]> www.pilppa.org Git - linux-2.6-omap-h63xx.git/commitdiff
[MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom...
authorMike Frysinger <vapier.adi@gmail.com>
Wed, 30 Jul 2008 19:35:01 +0000 (12:35 -0700)
committerDavid Woodhouse <David.Woodhouse@intel.com>
Fri, 1 Aug 2008 14:42:55 +0000 (15:42 +0100)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/Kconfig
drivers/mtd/nand/bf5xx_nand.c

index 71406e517857c456384ddd95ef51633119fe562a..c075b47e11ad912b6a4d1cf5053d1428e67dfbd6 100644 (file)
@@ -109,6 +109,18 @@ config MTD_NAND_BF5XX_HWECC
          Enable the use of the BF5XX's internal ECC generator when
          using NAND.
 
+config MTD_NAND_BF5XX_BOOTROM_ECC
+       bool "Use Blackfin BootROM ECC Layout"
+       default n
+       depends on MTD_NAND_BF5XX_HWECC
+       help
+         If you wish to modify NAND pages and allow the Blackfin on-chip
+         BootROM to boot from them, say Y here.  This is only necessary
+         if you are booting U-Boot out of NAND and you wish to update
+         U-Boot from Linux' userspace.  Otherwise, you should say N here.
+
+         If unsure, say N.
+
 config MTD_NAND_RTC_FROM4
        tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
        depends on SH_SOLUTION_ENGINE
index fc58afe4733ae1754b960d36459ee5ae49418d40..3555f6b3ebe00832a6ef6da7258d2ed3ce3b0bc5 100644 (file)
@@ -91,6 +91,41 @@ static const unsigned short bfin_nfc_pin_req[] =
         P_NAND_ALE,
         0};
 
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+static uint8_t bbt_pattern[] = { 0xff };
+
+static struct nand_bbt_descr bootrom_bbt = {
+       .options = 0,
+       .offs = 63,
+       .len = 1,
+       .pattern = bbt_pattern,
+};
+
+static struct nand_ecclayout bootrom_ecclayout = {
+       .eccbytes = 24,
+       .eccpos = {
+               0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
+               0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
+               0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
+               0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
+               0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
+               0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
+               0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
+               0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
+       },
+       .oobfree = {
+               { 0x8 * 0 + 3, 5 },
+               { 0x8 * 1 + 3, 5 },
+               { 0x8 * 2 + 3, 5 },
+               { 0x8 * 3 + 3, 5 },
+               { 0x8 * 4 + 3, 5 },
+               { 0x8 * 5 + 3, 5 },
+               { 0x8 * 6 + 3, 5 },
+               { 0x8 * 7 + 3, 5 },
+       }
+};
+#endif
+
 /*
  * Data structures for bf5xx nand flash controller driver
  */
@@ -712,6 +747,11 @@ static int bf5xx_nand_probe(struct platform_device *pdev)
 
        /* setup hardware ECC data struct */
        if (hardware_ecc) {
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+               chip->badblock_pattern = &bootrom_bbt;
+               chip->ecc.layout = &bootrom_ecclayout;
+#endif
+
                if (plat->page_size == NFC_PG_SIZE_256) {
                        chip->ecc.bytes = 3;
                        chip->ecc.size = 256;