]> www.pilppa.org Git - linux-2.6-omap-h63xx.git/commitdiff
atmel-mci: Don't stop the clock between transfers
authorHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Fri, 3 Oct 2008 15:48:16 +0000 (17:48 +0200)
committerHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Sun, 5 Oct 2008 18:39:20 +0000 (20:39 +0200)
Some cards might get upset if we turn off the clock for extended periods
of time. So keep the clock running until the mmc core tells us to turn
it off.

Also, don't reset the controller between each transfer. That was an
attempt to work around earlier bugs, and it never really worked very
well.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
drivers/mmc/host/atmel-mci.c

index d834e3756aefef25d2ddde908ef12e29acea4028..14ab28da7fa86c38b8f2b94b94235c855a9184df 100644 (file)
@@ -279,23 +279,6 @@ err:
                "failed to initialize debugfs for controller\n");
 }
 
-static void atmci_enable(struct atmel_mci *host)
-{
-       clk_enable(host->mck);
-       mci_writel(host, CR, MCI_CR_MCIEN);
-       mci_writel(host, MR, host->mode_reg);
-       mci_writel(host, SDCR, host->sdc_reg);
-}
-
-static void atmci_disable(struct atmel_mci *host)
-{
-       mci_writel(host, CR, MCI_CR_SWRST);
-
-       /* Stall until write is complete, then disable the bus clock */
-       mci_readl(host, SR);
-       clk_disable(host->mck);
-}
-
 static inline unsigned int ns_to_clocks(struct atmel_mci *host,
                                        unsigned int ns)
 {
@@ -408,8 +391,6 @@ static void atmci_request_end(struct mmc_host *mmc, struct mmc_request *mrq)
        WARN_ON(host->cmd || host->data);
        host->mrq = NULL;
 
-       atmci_disable(host);
-
        mmc_request_done(mmc, mrq);
 }
 
@@ -476,8 +457,6 @@ static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
        host->completed_events = 0;
        host->state = STATE_SENDING_CMD;
 
-       atmci_enable(host);
-
        /* We don't support multiple blocks of weird lengths. */
        data = mrq->data;
        if (data) {
@@ -520,7 +499,6 @@ static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
        return;
 
 fail:
-       atmci_disable(host);
        host->mrq = NULL;
        mrq->cmd->error = -EINVAL;
        mmc_request_done(mmc, mrq);
@@ -530,9 +508,21 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
        struct atmel_mci        *host = mmc_priv(mmc);
 
+       switch (ios->bus_width) {
+       case MMC_BUS_WIDTH_1:
+               host->sdc_reg = 0;
+               break;
+       case MMC_BUS_WIDTH_4:
+               host->sdc_reg = MCI_SDCBUS_4BIT;
+               break;
+       }
+
        if (ios->clock) {
                u32 clkdiv;
 
+               if (!host->mode_reg)
+                       clk_enable(host->mck);
+
                /* Set clock rate */
                clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * ios->clock) - 1;
                if (clkdiv > 255) {
@@ -544,26 +534,20 @@ static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
                host->mode_reg = MCI_MR_CLKDIV(clkdiv) | MCI_MR_WRPROOF
                                        | MCI_MR_RDPROOF;
-       }
 
-       switch (ios->bus_width) {
-       case MMC_BUS_WIDTH_1:
-               host->sdc_reg = 0;
-               break;
-       case MMC_BUS_WIDTH_4:
-               host->sdc_reg = MCI_SDCBUS_4BIT;
-               break;
+               mci_writel(host, CR, MCI_CR_MCIEN);
+               mci_writel(host, MR, host->mode_reg);
+               mci_writel(host, SDCR, host->sdc_reg);
+       } else {
+               mci_writel(host, CR, MCI_CR_MCIDIS);
+               if (host->mode_reg) {
+                       mci_readl(host, MR);
+                       clk_disable(host->mck);
+               }
+               host->mode_reg = 0;
        }
 
        switch (ios->power_mode) {
-       case MMC_POWER_ON:
-               /* Send init sequence (74 clock cycles) */
-               atmci_enable(host);
-               mci_writel(host, CMDR, MCI_CMDR_SPCMD_INIT);
-               while (!(mci_readl(host, SR) & MCI_CMDRDY))
-                       cpu_relax();
-               atmci_disable(host);
-               break;
        default:
                /*
                 * TODO: None of the currently available AVR32-based