initialized and attempts to bring up the supplied dev at the supplied
address.
-The remote host can run either 'netcat -u -l -p <port>' or syslogd.
+The remote host can run either 'netcat -u -l -p <port>',
+'nc -l -u <port>' or syslogd.
Dynamic reconfiguration:
========================
return 0;
}
+#ifdef CONFIG_IPPP_FILTER
static int get_filter(void __user *arg, struct sock_filter **p)
{
struct sock_fprog uprog;
*p = code;
return uprog.len;
}
+#endif /* CONFIG_IPPP_FILTER */
/*
* ippp device ioctl
/* bnx2x.h: Broadcom Everest network driver.
*
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#define bnx2x_fp(bp, nr, var) (bp->fp[nr].var)
-#define BNX2X_HAS_TX_WORK(fp) \
- ((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || \
- (fp->tx_pkt_prod != fp->tx_pkt_cons))
-
-#define BNX2X_HAS_RX_WORK(fp) \
- (fp->rx_comp_cons != rx_cons_sb)
-
-#define BNX2X_HAS_WORK(fp) (BNX2X_HAS_RX_WORK(fp) || BNX2X_HAS_TX_WORK(fp))
+#define BNX2X_HAS_WORK(fp) (bnx2x_has_rx_work(fp) || bnx2x_has_tx_work(fp))
/* MC hsi */
-/* Copyright 2008 Broadcom Corporation
+/* Copyright 2008-2009 Broadcom Corporation
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
val &= ~0x810;
EMAC_WR(bp, EMAC_REG_EMAC_MODE, val);
+ /* enable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
+
/* enable emac for jumbo packets */
EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE,
(EMAC_RX_MTU_SIZE_JUMBO_ENA |
u32 gp_status)
{
struct bnx2x *bp = params->bp;
-
+ u16 new_line_speed;
u8 rc = 0;
vars->link_status = 0;
switch (gp_status & GP_STATUS_SPEED_MASK) {
case GP_STATUS_10M:
- vars->line_speed = SPEED_10;
+ new_line_speed = SPEED_10;
if (vars->duplex == DUPLEX_FULL)
vars->link_status |= LINK_10TFD;
else
break;
case GP_STATUS_100M:
- vars->line_speed = SPEED_100;
+ new_line_speed = SPEED_100;
if (vars->duplex == DUPLEX_FULL)
vars->link_status |= LINK_100TXFD;
else
case GP_STATUS_1G:
case GP_STATUS_1G_KX:
- vars->line_speed = SPEED_1000;
+ new_line_speed = SPEED_1000;
if (vars->duplex == DUPLEX_FULL)
vars->link_status |= LINK_1000TFD;
else
break;
case GP_STATUS_2_5G:
- vars->line_speed = SPEED_2500;
+ new_line_speed = SPEED_2500;
if (vars->duplex == DUPLEX_FULL)
vars->link_status |= LINK_2500TFD;
else
case GP_STATUS_10G_KX4:
case GP_STATUS_10G_HIG:
case GP_STATUS_10G_CX4:
- vars->line_speed = SPEED_10000;
+ new_line_speed = SPEED_10000;
vars->link_status |= LINK_10GTFD;
break;
case GP_STATUS_12G_HIG:
- vars->line_speed = SPEED_12000;
+ new_line_speed = SPEED_12000;
vars->link_status |= LINK_12GTFD;
break;
case GP_STATUS_12_5G:
- vars->line_speed = SPEED_12500;
+ new_line_speed = SPEED_12500;
vars->link_status |= LINK_12_5GTFD;
break;
case GP_STATUS_13G:
- vars->line_speed = SPEED_13000;
+ new_line_speed = SPEED_13000;
vars->link_status |= LINK_13GTFD;
break;
case GP_STATUS_15G:
- vars->line_speed = SPEED_15000;
+ new_line_speed = SPEED_15000;
vars->link_status |= LINK_15GTFD;
break;
case GP_STATUS_16G:
- vars->line_speed = SPEED_16000;
+ new_line_speed = SPEED_16000;
vars->link_status |= LINK_16GTFD;
break;
break;
}
+ /* Upon link speed change set the NIG into drain mode.
+ Comes to deals with possible FIFO glitch due to clk change
+ when speed is decreased without link down indicator */
+ if (new_line_speed != vars->line_speed) {
+ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE
+ + params->port*4, 0);
+ msleep(1);
+ }
+ vars->line_speed = new_line_speed;
vars->link_status |= LINK_STATUS_SERDES_LINK;
if ((params->req_line_speed == SPEED_AUTO_NEG) &&
(MDIO_REG_BANK_CL73_IEEEB0 +
(MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)),
0x6041);
-
+ msleep(200);
/* set aer mmd back */
bnx2x_set_aer_mmd(params, vars);
}
if (vars->phy_flags & PHY_XGXS_FLAG) {
- if (params->req_line_speed &&
+ if ((params->req_line_speed &&
((params->req_line_speed == SPEED_100) ||
- (params->req_line_speed == SPEED_10))) {
+ (params->req_line_speed == SPEED_10))) ||
+ (!params->req_line_speed &&
+ (params->speed_cap_mask >=
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) &&
+ (params->speed_cap_mask <
+ PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)
+ )) {
vars->phy_flags |= PHY_SGMII_FLAG;
} else {
vars->phy_flags &= ~PHY_SGMII_FLAG;
/* activate nig drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1);
+ /* disable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
+ msleep(10);
+
/* reset BigMac */
bnx2x_bmac_rx_disable(bp, params->port);
REG_WR(bp, GRCBASE_MISC +
/* update shared memory */
bnx2x_update_mng(params, vars->link_status);
+ msleep(20);
return rc;
}
/* This function should called upon link interrupt */
REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68),
REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68));
+ /* disable emac */
+ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0);
+
ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config);
/* Check external link change only for non-direct */
ext_phy_addr[port],
MDIO_PMA_DEVAD,
MDIO_PMA_REG_ROM_VER1, &fw_ver1);
- if (fw_ver1 == 0) {
+ if (fw_ver1 == 0 || fw_ver1 == 0x4321) {
DP(NETIF_MSG_LINK,
- "bnx2x_8073_common_init_phy port %x "
- "fw Download failed\n", port);
+ "bnx2x_8073_common_init_phy port %x:"
+ "Download failed. fw version = 0x%x\n",
+ port, fw_ver1);
return -EINVAL;
}
/* bnx2x_main.c: Broadcom Everest network driver.
*
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include "bnx2x.h"
#include "bnx2x_init.h"
-#define DRV_MODULE_VERSION "1.45.23"
-#define DRV_MODULE_RELDATE "2008/11/03"
+#define DRV_MODULE_VERSION "1.45.26"
+#define DRV_MODULE_RELDATE "2009/01/26"
#define BNX2X_BC_VER 0x040200
/* Time in jiffies before concluding the transmitter is hung */
DRV_MODULE_NAME " " DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n";
MODULE_AUTHOR("Eliezer Tamir");
-MODULE_DESCRIPTION("Broadcom NetXtreme II BCM57710 Driver");
+MODULE_DESCRIPTION("Broadcom NetXtreme II BCM57710/57711/57711E Driver");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_MODULE_VERSION);
* fast path service functions
*/
+static inline int bnx2x_has_tx_work(struct bnx2x_fastpath *fp)
+{
+ u16 tx_cons_sb;
+
+ /* Tell compiler that status block fields can change */
+ barrier();
+ tx_cons_sb = le16_to_cpu(*fp->tx_cons_sb);
+ return (fp->tx_pkt_cons != tx_cons_sb);
+}
+
+static inline int bnx2x_has_tx_work_unload(struct bnx2x_fastpath *fp)
+{
+ /* Tell compiler that consumer and producer can change */
+ barrier();
+ return (fp->tx_pkt_prod != fp->tx_pkt_cons);
+
+}
+
/* free skb in the packet ring at pos idx
* return idx of last bd freed
*/
}
+static void bnx2x_reset_common(struct bnx2x *bp)
+{
+ /* reset_common */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR,
+ 0xd3ffff7f);
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 0x1403);
+}
+
static int bnx2x_init_common(struct bnx2x *bp)
{
u32 val, i;
DP(BNX2X_MSG_MCP, "starting common init func %d\n", BP_FUNC(bp));
+ bnx2x_reset_common(bp);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0xffffffff);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 0xfffc);
static void bnx2x_netif_stop(struct bnx2x *bp, int disable_hw)
{
bnx2x_int_disable_sync(bp, disable_hw);
+ bnx2x_napi_disable(bp);
if (netif_running(bp->dev)) {
- bnx2x_napi_disable(bp);
netif_tx_disable(bp->dev);
bp->dev->trans_start = jiffies; /* prevent tx timeout */
}
* multicast 64-127:port0 128-191:port1
*/
config->hdr.length_6b = 2;
- config->hdr.offset = port ? 31 : 0;
+ config->hdr.offset = port ? 32 : 0;
config->hdr.client_id = BP_CL_ID(bp);
config->hdr.reserved1 = 0;
static int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
{
u32 load_code;
- int i, rc;
+ int i, rc = 0;
#ifdef BNX2X_STOP_ON_ERROR
if (unlikely(bp->panic))
return -EPERM;
bp->state = BNX2X_STATE_OPENING_WAIT4_LOAD;
- /* Send LOAD_REQUEST command to MCP
- Returns the type of LOAD command:
- if it is the first port to be initialized
- common blocks should be initialized, otherwise - not
- */
- if (!BP_NOMCP(bp)) {
- load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_REQ);
- if (!load_code) {
- BNX2X_ERR("MCP response failure, aborting\n");
- return -EBUSY;
- }
- if (load_code == FW_MSG_CODE_DRV_LOAD_REFUSED)
- return -EBUSY; /* other port in diagnostic mode */
-
- } else {
- int port = BP_PORT(bp);
-
- DP(NETIF_MSG_IFUP, "NO MCP load counts before us %d, %d, %d\n",
- load_count[0], load_count[1], load_count[2]);
- load_count[0]++;
- load_count[1 + port]++;
- DP(NETIF_MSG_IFUP, "NO MCP new load counts %d, %d, %d\n",
- load_count[0], load_count[1], load_count[2]);
- if (load_count[0] == 1)
- load_code = FW_MSG_CODE_DRV_LOAD_COMMON;
- else if (load_count[1 + port] == 1)
- load_code = FW_MSG_CODE_DRV_LOAD_PORT;
- else
- load_code = FW_MSG_CODE_DRV_LOAD_FUNCTION;
- }
-
- if ((load_code == FW_MSG_CODE_DRV_LOAD_COMMON) ||
- (load_code == FW_MSG_CODE_DRV_LOAD_PORT))
- bp->port.pmf = 1;
- else
- bp->port.pmf = 0;
- DP(NETIF_MSG_LINK, "pmf %d\n", bp->port.pmf);
-
- /* if we can't use MSI-X we only need one fp,
- * so try to enable MSI-X with the requested number of fp's
- * and fallback to inta with one fp
- */
if (use_inta) {
bp->num_queues = 1;
else
bp->num_queues = 1;
- if (bnx2x_enable_msix(bp)) {
+ DP(NETIF_MSG_IFUP,
+ "set number of queues to %d\n", bp->num_queues);
+
+ /* if we can't use MSI-X we only need one fp,
+ * so try to enable MSI-X with the requested number of fp's
+ * and fallback to MSI or legacy INTx with one fp
+ */
+ rc = bnx2x_enable_msix(bp);
+ if (rc) {
/* failed to enable MSI-X */
bp->num_queues = 1;
if (use_multi)
" to enable MSI-X\n");
}
}
- DP(NETIF_MSG_IFUP,
- "set number of queues to %d\n", bp->num_queues);
if (bnx2x_alloc_mem(bp))
return -ENOMEM;
bnx2x_fp(bp, i, disable_tpa) =
((bp->flags & TPA_ENABLE_FLAG) == 0);
+ for_each_queue(bp, i)
+ netif_napi_add(bp->dev, &bnx2x_fp(bp, i, napi),
+ bnx2x_poll, 128);
+
+#ifdef BNX2X_STOP_ON_ERROR
+ for_each_queue(bp, i) {
+ struct bnx2x_fastpath *fp = &bp->fp[i];
+
+ fp->poll_no_work = 0;
+ fp->poll_calls = 0;
+ fp->poll_max_calls = 0;
+ fp->poll_complete = 0;
+ fp->poll_exit = 0;
+ }
+#endif
+ bnx2x_napi_enable(bp);
+
if (bp->flags & USING_MSIX_FLAG) {
rc = bnx2x_req_msix_irqs(bp);
if (rc) {
pci_disable_msix(bp->pdev);
- goto load_error;
+ goto load_error1;
}
+ printk(KERN_INFO PFX "%s: using MSI-X\n", bp->dev->name);
} else {
bnx2x_ack_int(bp);
rc = bnx2x_req_irq(bp);
if (rc) {
- BNX2X_ERR("IRQ request failed, aborting\n");
- goto load_error;
+ BNX2X_ERR("IRQ request failed rc %d, aborting\n", rc);
+ goto load_error1;
}
}
- for_each_queue(bp, i)
- netif_napi_add(bp->dev, &bnx2x_fp(bp, i, napi),
- bnx2x_poll, 128);
+ /* Send LOAD_REQUEST command to MCP
+ Returns the type of LOAD command:
+ if it is the first port to be initialized
+ common blocks should be initialized, otherwise - not
+ */
+ if (!BP_NOMCP(bp)) {
+ load_code = bnx2x_fw_command(bp, DRV_MSG_CODE_LOAD_REQ);
+ if (!load_code) {
+ BNX2X_ERR("MCP response failure, aborting\n");
+ rc = -EBUSY;
+ goto load_error2;
+ }
+ if (load_code == FW_MSG_CODE_DRV_LOAD_REFUSED) {
+ rc = -EBUSY; /* other port in diagnostic mode */
+ goto load_error2;
+ }
+
+ } else {
+ int port = BP_PORT(bp);
+
+ DP(NETIF_MSG_IFUP, "NO MCP load counts before us %d, %d, %d\n",
+ load_count[0], load_count[1], load_count[2]);
+ load_count[0]++;
+ load_count[1 + port]++;
+ DP(NETIF_MSG_IFUP, "NO MCP new load counts %d, %d, %d\n",
+ load_count[0], load_count[1], load_count[2]);
+ if (load_count[0] == 1)
+ load_code = FW_MSG_CODE_DRV_LOAD_COMMON;
+ else if (load_count[1 + port] == 1)
+ load_code = FW_MSG_CODE_DRV_LOAD_PORT;
+ else
+ load_code = FW_MSG_CODE_DRV_LOAD_FUNCTION;
+ }
+
+ if ((load_code == FW_MSG_CODE_DRV_LOAD_COMMON) ||
+ (load_code == FW_MSG_CODE_DRV_LOAD_PORT))
+ bp->port.pmf = 1;
+ else
+ bp->port.pmf = 0;
+ DP(NETIF_MSG_LINK, "pmf %d\n", bp->port.pmf);
/* Initialize HW */
rc = bnx2x_init_hw(bp, load_code);
if (rc) {
BNX2X_ERR("HW init failed, aborting\n");
- goto load_int_disable;
+ goto load_error2;
}
/* Setup NIC internals and enable interrupts */
if (!load_code) {
BNX2X_ERR("MCP response failure, aborting\n");
rc = -EBUSY;
- goto load_rings_free;
+ goto load_error3;
}
}
rc = bnx2x_setup_leading(bp);
if (rc) {
BNX2X_ERR("Setup leading failed!\n");
- goto load_netif_stop;
+ goto load_error3;
}
if (CHIP_IS_E1H(bp))
for_each_nondefault_queue(bp, i) {
rc = bnx2x_setup_multi(bp, i);
if (rc)
- goto load_netif_stop;
+ goto load_error3;
}
if (CHIP_IS_E1(bp))
case LOAD_NORMAL:
/* Tx queue should be only reenabled */
netif_wake_queue(bp->dev);
+ /* Initialize the receive filter. */
bnx2x_set_rx_mode(bp->dev);
break;
case LOAD_OPEN:
netif_start_queue(bp->dev);
+ /* Initialize the receive filter. */
bnx2x_set_rx_mode(bp->dev);
- if (bp->flags & USING_MSIX_FLAG)
- printk(KERN_INFO PFX "%s: using MSI-X\n",
- bp->dev->name);
break;
case LOAD_DIAG:
+ /* Initialize the receive filter. */
bnx2x_set_rx_mode(bp->dev);
bp->state = BNX2X_STATE_DIAG;
break;
return 0;
-load_netif_stop:
- bnx2x_napi_disable(bp);
-load_rings_free:
+load_error3:
+ bnx2x_int_disable_sync(bp, 1);
+ if (!BP_NOMCP(bp)) {
+ bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_REQ_WOL_MCP);
+ bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE);
+ }
+ bp->port.pmf = 0;
/* Free SKBs, SGEs, TPA pool and driver internals */
bnx2x_free_skbs(bp);
for_each_queue(bp, i)
bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE);
-load_int_disable:
- bnx2x_int_disable_sync(bp, 1);
+load_error2:
/* Release IRQs */
bnx2x_free_irq(bp);
-load_error:
+load_error1:
+ bnx2x_napi_disable(bp);
+ for_each_queue(bp, i)
+ netif_napi_del(&bnx2x_fp(bp, i, napi));
bnx2x_free_mem(bp);
- bp->port.pmf = 0;
/* TBD we really need to reset the chip
if we want to recover from this */
}
cnt--;
msleep(1);
+ rmb(); /* Refresh the dsb_sp_prod */
}
bp->state = BNX2X_STATE_CLOSING_WAIT4_UNLOAD;
bp->fp[0].state = BNX2X_FP_STATE_CLOSED;
/* TODO: Close Doorbell port? */
}
-static void bnx2x_reset_common(struct bnx2x *bp)
-{
- /* reset_common */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR,
- 0xd3ffff7f);
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 0x1403);
-}
-
static void bnx2x_reset_chip(struct bnx2x *bp, u32 reset_code)
{
DP(BNX2X_MSG_MCP, "function %d reset_code %x\n",
bnx2x_set_storm_rx_mode(bp);
bnx2x_netif_stop(bp, 1);
- if (!netif_running(bp->dev))
- bnx2x_napi_disable(bp);
+
del_timer_sync(&bp->timer);
SHMEM_WR(bp, func_mb[BP_FUNC(bp)].drv_pulse_mb,
(DRV_PULSE_ALWAYS_ALIVE | bp->fw_drv_pulse_wr_seq));
bnx2x_stats_handle(bp, STATS_EVENT_STOP);
+ /* Release IRQs */
+ bnx2x_free_irq(bp);
+
/* Wait until tx fast path tasks complete */
for_each_queue(bp, i) {
struct bnx2x_fastpath *fp = &bp->fp[i];
cnt = 1000;
smp_rmb();
- while (BNX2X_HAS_TX_WORK(fp)) {
+ while (bnx2x_has_tx_work_unload(fp)) {
bnx2x_tx_int(fp, 1000);
if (!cnt) {
/* Give HW time to discard old tx messages */
msleep(1);
- /* Release IRQs */
- bnx2x_free_irq(bp);
-
if (CHIP_IS_E1(bp)) {
struct mac_configuration_cmd *config =
bnx2x_sp(bp, mcast_config);
bnx2x_free_skbs(bp);
for_each_queue(bp, i)
bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE);
+ for_each_queue(bp, i)
+ netif_napi_del(&bnx2x_fp(bp, i, napi));
bnx2x_free_mem(bp);
bp->state = BNX2X_STATE_CLOSED;
*/
bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
val = REG_RD(bp, DORQ_REG_NORM_CID_OFST);
- if (val == 0x7)
- REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0);
- bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
-
if (val == 0x7) {
u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
/* save our func */
u32 swap_en;
u32 swap_val;
+ /* clear the UNDI indication */
+ REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0);
+
BNX2X_DEV_INFO("UNDI is active! reset device\n");
/* try unload UNDI on port 0 */
bnx2x_fw_command(bp, reset_code);
}
+ /* now it's safe to release the lock */
+ bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
+
REG_WR(bp, (BP_PORT(bp) ? HC_REG_CONFIG_1 :
HC_REG_CONFIG_0), 0x1000);
bp->fw_seq =
(SHMEM_RD(bp, func_mb[bp->func].drv_mb_header) &
DRV_MSG_SEQ_NUMBER_MASK);
- }
+
+ } else
+ bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
}
}
id |= ((val & 0xf) << 12);
val = REG_RD(bp, MISC_REG_CHIP_METAL);
id |= ((val & 0xff) << 4);
- REG_RD(bp, MISC_REG_BOND_ID);
+ val = REG_RD(bp, MISC_REG_BOND_ID);
id |= (val & 0xf);
bp->common.chip_id = id;
bp->link_params.chip_id = bp->common.chip_id;
struct bnx2x *bp = netdev_priv(dev);
int rc;
+ if (!netif_running(dev))
+ return -EAGAIN;
+
DP(BNX2X_MSG_NVM, "ethtool_eeprom: cmd %d\n"
DP_LEVEL " magic 0x%x offset 0x%x (%d) len 0x%x (%d)\n",
eeprom->cmd, eeprom->magic, eeprom->offset, eeprom->offset,
if (loopback_mode == BNX2X_MAC_LOOPBACK) {
bp->link_params.loopback_mode = LOOPBACK_BMAC;
- bnx2x_acquire_phy_lock(bp);
bnx2x_phy_init(&bp->link_params, &bp->link_vars);
- bnx2x_release_phy_lock(bp);
} else if (loopback_mode == BNX2X_PHY_LOOPBACK) {
+ u16 cnt = 1000;
bp->link_params.loopback_mode = LOOPBACK_XGXS_10;
- bnx2x_acquire_phy_lock(bp);
bnx2x_phy_init(&bp->link_params, &bp->link_vars);
- bnx2x_release_phy_lock(bp);
/* wait until link state is restored */
- bnx2x_wait_for_link(bp, link_up);
-
+ if (link_up)
+ while (cnt-- && bnx2x_test_link(&bp->link_params,
+ &bp->link_vars))
+ msleep(10);
} else
return -EINVAL;
return BNX2X_LOOPBACK_FAILED;
bnx2x_netif_stop(bp, 1);
+ bnx2x_acquire_phy_lock(bp);
if (bnx2x_run_loopback(bp, BNX2X_MAC_LOOPBACK, link_up)) {
DP(NETIF_MSG_PROBE, "MAC loopback failed\n");
rc |= BNX2X_PHY_LOOPBACK_FAILED;
}
+ bnx2x_release_phy_lock(bp);
bnx2x_netif_start(bp);
return rc;
return -ENODEV;
config->hdr.length_6b = 0;
- config->hdr.offset = 0;
+ if (CHIP_IS_E1(bp))
+ config->hdr.offset = (BP_PORT(bp) ? 32 : 0);
+ else
+ config->hdr.offset = BP_FUNC(bp);
config->hdr.client_id = BP_CL_ID(bp);
config->hdr.reserved1 = 0;
return 0;
}
+static inline int bnx2x_has_rx_work(struct bnx2x_fastpath *fp)
+{
+ u16 rx_cons_sb;
+
+ /* Tell compiler that status block fields can change */
+ barrier();
+ rx_cons_sb = le16_to_cpu(*fp->rx_cons_sb);
+ if ((rx_cons_sb & MAX_RCQ_DESC_CNT) == MAX_RCQ_DESC_CNT)
+ rx_cons_sb++;
+ return (fp->rx_comp_cons != rx_cons_sb);
+}
+
/*
* net_device service functions
*/
napi);
struct bnx2x *bp = fp->bp;
int work_done = 0;
- u16 rx_cons_sb;
#ifdef BNX2X_STOP_ON_ERROR
if (unlikely(bp->panic))
bnx2x_update_fpsb_idx(fp);
- if (BNX2X_HAS_TX_WORK(fp))
+ if (bnx2x_has_tx_work(fp))
bnx2x_tx_int(fp, budget);
- rx_cons_sb = le16_to_cpu(*fp->rx_cons_sb);
- if ((rx_cons_sb & MAX_RCQ_DESC_CNT) == MAX_RCQ_DESC_CNT)
- rx_cons_sb++;
- if (BNX2X_HAS_RX_WORK(fp))
+ if (bnx2x_has_rx_work(fp))
work_done = bnx2x_rx_int(fp, budget);
-
rmb(); /* BNX2X_HAS_WORK() reads the status block */
- rx_cons_sb = le16_to_cpu(*fp->rx_cons_sb);
- if ((rx_cons_sb & MAX_RCQ_DESC_CNT) == MAX_RCQ_DESC_CNT)
- rx_cons_sb++;
/* must not complete if we consumed full budget */
if ((work_done < budget) && !BNX2X_HAS_WORK(fp)) {
return rc;
}
+#if (MAX_SKB_FRAGS >= MAX_FETCH_BD - 3)
/* check if packet requires linearization (packet is too fragmented) */
static int bnx2x_pkt_req_lin(struct bnx2x *bp, struct sk_buff *skb,
u32 xmit_type)
return to_copy;
}
+#endif
/* called with netif_tx_lock
* bnx2x_tx_int() runs without netif_tx_lock unless it needs to call
skb->ip_summed, skb->protocol, ipv6_hdr(skb)->nexthdr,
ip_hdr(skb)->protocol, skb_shinfo(skb)->gso_type, xmit_type);
+#if (MAX_SKB_FRAGS >= MAX_FETCH_BD - 3)
/* First, check if we need to linearize the skb
(due to FW restrictions) */
if (bnx2x_pkt_req_lin(bp, skb, xmit_type)) {
return NETDEV_TX_OK;
}
}
+#endif
/*
Please read carefully. First we use one BD which we mark as start,
{
struct bnx2x *bp = netdev_priv(dev);
+ netif_carrier_off(dev);
+
bnx2x_set_power_state(bp, PCI_D0);
return bnx2x_nic_load(bp, LOAD_OPEN);
for (; i < old; i++) {
if (CAM_IS_INVALID(config->
config_table[i])) {
- i--; /* already invalidated */
+ /* already invalidated */
break;
}
/* invalidate */
return rc;
}
- rc = register_netdev(dev);
- if (rc) {
- dev_err(&pdev->dev, "Cannot register net device\n");
- goto init_one_exit;
- }
-
pci_set_drvdata(pdev, dev);
rc = bnx2x_init_bp(bp);
+ if (rc)
+ goto init_one_exit;
+
+ rc = register_netdev(dev);
if (rc) {
- unregister_netdev(dev);
+ dev_err(&pdev->dev, "Cannot register net device\n");
goto init_one_exit;
}
- netif_carrier_off(dev);
-
bp->common.name = board_info[ent->driver_data].name;
printk(KERN_INFO "%s: %s (%c%d) PCI-E x%d %s found at mem %lx,"
" IRQ %d, ", dev->name, bp->common.name,
bnx2x_free_skbs(bp);
for_each_queue(bp, i)
bnx2x_free_rx_sge_range(bp, bp->fp + i, NUM_RX_SGE);
+ for_each_queue(bp, i)
+ netif_napi_del(&bnx2x_fp(bp, i, napi));
bnx2x_free_mem(bp);
bp->state = BNX2X_STATE_CLOSED;
/* bnx2x_reg.h: Broadcom Everest network driver.
*
- * Copyright (c) 2007-2008 Broadcom Corporation
+ * Copyright (c) 2007-2009 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
{
lro_mgr->dev = qs->netdev;
lro_mgr->features = LRO_F_NAPI;
+ lro_mgr->frag_align_pad = NET_IP_ALIGN;
lro_mgr->ip_summed = CHECKSUM_UNNECESSARY;
lro_mgr->ip_summed_aggr = CHECKSUM_UNNECESSARY;
lro_mgr->max_desc = T3_MAX_LRO_SES;
ew32(PBA_ECC, reg);
}
- /* PCI-Ex Control Register */
+ /* PCI-Ex Control Registers */
if (hw->mac.type == e1000_82574) {
reg = er32(GCR);
reg |= (1 << 22);
ew32(GCR, reg);
+
+ reg = er32(GCR2);
+ reg |= 1;
+ ew32(GCR2, reg);
}
return;
E1000_MANC2H = 0x05860, /* Management Control To Host - RW */
E1000_SW_FW_SYNC = 0x05B5C, /* Software-Firmware Synchronization - RW */
E1000_GCR = 0x05B00, /* PCI-Ex Control */
+ E1000_GCR2 = 0x05B64, /* PCI-Ex Control #2 */
E1000_FACTPS = 0x05B30, /* Function Active and Power State to MNG */
E1000_SWSM = 0x05B50, /* SW Semaphore */
E1000_FWSM = 0x05B54, /* FW Semaphore */
{
struct gfar_private *priv = netdev_priv(dev);
unsigned long flags;
- struct vlan_group *old_grp;
u32 tempval;
spin_lock_irqsave(&priv->rxlock, flags);
- old_grp = priv->vlgrp;
-
- if (old_grp == grp)
- return;
+ priv->vlgrp = grp;
if (grp) {
/* Enable VLAN tag insertion */
rxctrl |= dca3_get_tag(&adapter->pdev->dev, cpu);
rxctrl |= IXGBE_DCA_RXCTRL_DESC_DCA_EN;
rxctrl |= IXGBE_DCA_RXCTRL_HEAD_DCA_EN;
+ rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_RRO_EN);
+ rxctrl &= ~(IXGBE_DCA_RXCTRL_DESC_WRO_EN |
+ IXGBE_DCA_RXCTRL_DESC_HSRO_EN);
IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_RXCTRL(q), rxctrl);
rx_ring->cpu = cpu;
}
IXGBE_WRITE_REG(hw, IXGBE_RXCSUM, rxcsum);
}
+static void ixgbe_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ /* add VID to filter table */
+ hw->mac.ops.set_vfta(&adapter->hw, vid, 0, true);
+}
+
+static void ixgbe_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(netdev);
+ struct ixgbe_hw *hw = &adapter->hw;
+
+ if (!test_bit(__IXGBE_DOWN, &adapter->state))
+ ixgbe_irq_disable(adapter);
+
+ vlan_group_set_device(adapter->vlgrp, vid, NULL);
+
+ if (!test_bit(__IXGBE_DOWN, &adapter->state))
+ ixgbe_irq_enable(adapter);
+
+ /* remove VID from filter table */
+ hw->mac.ops.set_vfta(&adapter->hw, vid, 0, false);
+}
+
static void ixgbe_vlan_rx_register(struct net_device *netdev,
struct vlan_group *grp)
{
ctrl |= IXGBE_VLNCTRL_VME;
ctrl &= ~IXGBE_VLNCTRL_CFIEN;
IXGBE_WRITE_REG(&adapter->hw, IXGBE_VLNCTRL, ctrl);
+ ixgbe_vlan_rx_add_vid(netdev, 0);
if (grp) {
/* enable VLAN tag insert/strip */
ixgbe_irq_enable(adapter);
}
-static void ixgbe_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
-{
- struct ixgbe_adapter *adapter = netdev_priv(netdev);
- struct ixgbe_hw *hw = &adapter->hw;
-
- /* add VID to filter table */
- hw->mac.ops.set_vfta(&adapter->hw, vid, 0, true);
-}
-
-static void ixgbe_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
-{
- struct ixgbe_adapter *adapter = netdev_priv(netdev);
- struct ixgbe_hw *hw = &adapter->hw;
-
- if (!test_bit(__IXGBE_DOWN, &adapter->state))
- ixgbe_irq_disable(adapter);
-
- vlan_group_set_device(adapter->vlgrp, vid, NULL);
-
- if (!test_bit(__IXGBE_DOWN, &adapter->state))
- ixgbe_irq_enable(adapter);
-
- /* remove VID from filter table */
- hw->mac.ops.set_vfta(&adapter->hw, vid, 0, false);
-}
-
static void ixgbe_restore_vlan(struct ixgbe_adapter *adapter)
{
ixgbe_vlan_rx_register(adapter->netdev, adapter->vlgrp);
ixgbe_irq_enable(adapter);
+ /* enable transmits */
+ netif_tx_start_all_queues(netdev);
+
/* bring the link up in the watchdog, this could race with our first
* link up interrupt but shouldn't be a problem */
adapter->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
(FLOW_TX ? "TX" : "None"))));
netif_carrier_on(netdev);
- netif_tx_wake_all_queues(netdev);
} else {
/* Force detection of hung controller */
adapter->detect_tx_hung = true;
printk(KERN_INFO "ixgbe: %s NIC Link is Down\n",
netdev->name);
netif_carrier_off(netdev);
- netif_tx_stop_all_queues(netdev);
}
}
}
netif_carrier_off(netdev);
- netif_tx_stop_all_queues(netdev);
strcpy(netdev->name, "eth%d");
err = register_netdev(netdev);
#define IXGBE_DCA_RXCTRL_DESC_DCA_EN (1 << 5) /* DCA Rx Desc enable */
#define IXGBE_DCA_RXCTRL_HEAD_DCA_EN (1 << 6) /* DCA Rx Desc header enable */
#define IXGBE_DCA_RXCTRL_DATA_DCA_EN (1 << 7) /* DCA Rx Desc payload enable */
+#define IXGBE_DCA_RXCTRL_DESC_RRO_EN (1 << 9) /* DCA Rx rd Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_WRO_EN (1 << 13) /* DCA Rx wr Desc Relax Order */
+#define IXGBE_DCA_RXCTRL_DESC_HSRO_EN (1 << 15) /* DCA Rx Split Header RO */
#define IXGBE_DCA_TXCTRL_CPUID_MASK 0x0000001F /* Tx CPUID Mask */
#define IXGBE_DCA_TXCTRL_DESC_DCA_EN (1 << 5) /* DCA Tx Desc enable */
if (devcs & ETH_RX_MP)
dev->stats.multicast++;
+ /* 16 bit align */
+ skb_reserve(skb_new, 2);
+
lp->rx_skb[lp->rx_next_done] = skb_new;
}
static void korina_alloc_ring(struct net_device *dev)
{
struct korina_private *lp = netdev_priv(dev);
+ struct sk_buff *skb;
int i;
/* Initialize the transmit descriptors */
/* Initialize the receive descriptors */
for (i = 0; i < KORINA_NUM_RDS; i++) {
- struct sk_buff *skb = lp->rx_skb[i];
-
skb = dev_alloc_skb(KORINA_RBSIZE + 2);
if (!skb)
break;
lp->rd_ring[i].link = CPHYSADDR(&lp->rd_ring[i+1]);
}
- /* loop back */
- lp->rd_ring[i].link = CPHYSADDR(&lp->rd_ring[0]);
- lp->rx_next_done = 0;
+ /* loop back receive descriptors, so the last
+ * descriptor points to the first one */
+ lp->rd_ring[i - 1].link = CPHYSADDR(&lp->rd_ring[0]);
+ lp->rd_ring[i - 1].control |= DMA_DESC_COD;
- lp->rd_ring[i].control |= DMA_DESC_COD;
+ lp->rx_next_done = 0;
lp->rx_chain_head = 0;
lp->rx_chain_tail = 0;
lp->rx_chain_status = desc_empty;
printk(KERN_ERR "%s: TX underrun, resetting buffers\n",
bp->dev->name);
+ /* Transfer ongoing, disable transmitter, to avoid confusion */
+ if (status & MACB_BIT(TGO))
+ macb_writel(bp, NCR, macb_readl(bp, NCR) & ~MACB_BIT(TE));
+
head = bp->tx_head;
/*Mark all the buffer as used to avoid sending a lost buffer*/
}
bp->tx_head = bp->tx_tail = 0;
+
+ /* Enable the transmitter again */
+ if (status & MACB_BIT(TGO))
+ macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(TE));
}
if (!(status & MACB_BIT(COMP)))
/*
* SDMA configuration register.
*/
+#define RX_BURST_SIZE_4_64BIT (2 << 1)
#define RX_BURST_SIZE_16_64BIT (4 << 1)
#define BLM_RX_NO_SWAP (1 << 4)
#define BLM_TX_NO_SWAP (1 << 5)
+#define TX_BURST_SIZE_4_64BIT (2 << 22)
#define TX_BURST_SIZE_16_64BIT (4 << 22)
#if defined(__BIG_ENDIAN)
#define PORT_SDMA_CONFIG_DEFAULT_VALUE \
- (RX_BURST_SIZE_16_64BIT | \
- TX_BURST_SIZE_16_64BIT)
+ (RX_BURST_SIZE_4_64BIT | \
+ TX_BURST_SIZE_4_64BIT)
#elif defined(__LITTLE_ENDIAN)
#define PORT_SDMA_CONFIG_DEFAULT_VALUE \
- (RX_BURST_SIZE_16_64BIT | \
- BLM_RX_NO_SWAP | \
- BLM_TX_NO_SWAP | \
- TX_BURST_SIZE_16_64BIT)
+ (RX_BURST_SIZE_4_64BIT | \
+ BLM_RX_NO_SWAP | \
+ BLM_TX_NO_SWAP | \
+ TX_BURST_SIZE_4_64BIT)
#else
#error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined
#endif
entry = addr_crc(a);
}
- table[entry >> 2] |= 1 << (entry & 3);
+ table[entry >> 2] |= 1 << (8 * (entry & 3));
}
for (i = 0; i < 0x100; i += 4) {
struct mv643xx_eth_private *mp = netdev_priv(dev);
int i;
+ wrlp(mp, INT_MASK_EXT, 0x00000000);
wrlp(mp, INT_MASK, 0x00000000);
rdlp(mp, INT_MASK);
/*************************************************************************
* myri10ge.c: Myricom Myri-10G Ethernet driver.
*
- * Copyright (C) 2005 - 2007 Myricom, Inc.
+ * Copyright (C) 2005 - 2009 Myricom, Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
#include "myri10ge_mcp.h"
#include "myri10ge_mcp_gen_header.h"
-#define MYRI10GE_VERSION_STR "1.4.4-1.398"
+#define MYRI10GE_VERSION_STR "1.4.4-1.401"
MODULE_DESCRIPTION("Myricom 10G driver (10GbE)");
MODULE_AUTHOR("Maintainer: help@myri.com");
if (status != 0) {
dev_err(&pdev->dev, "Error %d writing PCI_EXP_DEVCTL\n",
status);
- goto abort_with_netdev;
+ goto abort_with_enabled;
}
pci_set_master(pdev);
}
if (status != 0) {
dev_err(&pdev->dev, "Error %d setting DMA mask\n", status);
- goto abort_with_netdev;
+ goto abort_with_enabled;
}
(void)pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
mgp->cmd = dma_alloc_coherent(&pdev->dev, sizeof(*mgp->cmd),
&mgp->cmd_bus, GFP_KERNEL);
if (mgp->cmd == NULL)
- goto abort_with_netdev;
+ goto abort_with_enabled;
mgp->board_span = pci_resource_len(pdev, 0);
mgp->iomem_base = pci_resource_start(pdev, 0);
dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd),
mgp->cmd, mgp->cmd_bus);
-abort_with_netdev:
+abort_with_enabled:
+ pci_disable_device(pdev);
+abort_with_netdev:
free_netdev(netdev);
return status;
}
mgp->cmd, mgp->cmd_bus);
free_netdev(netdev);
+ pci_disable_device(pdev);
pci_set_drvdata(pdev, NULL);
}
#define MAX_RX_BUFFER_LENGTH 1760
#define MAX_RX_JUMBO_BUFFER_LENGTH 8062
-#define MAX_RX_LRO_BUFFER_LENGTH ((48*1024)-512)
+#define MAX_RX_LRO_BUFFER_LENGTH (8062)
#define RX_DMA_MAP_LEN (MAX_RX_BUFFER_LENGTH - 2)
#define RX_JUMBO_DMA_MAP_LEN \
(MAX_RX_JUMBO_BUFFER_LENGTH - 2)
#define MAX_CMD_DESCRIPTORS 4096
#define MAX_RCV_DESCRIPTORS 16384
-#define MAX_CMD_DESCRIPTORS_HOST (MAX_CMD_DESCRIPTORS / 4)
-#define MAX_RCV_DESCRIPTORS_1G (MAX_RCV_DESCRIPTORS / 4)
-#define MAX_RCV_DESCRIPTORS_10G 8192
-#define MAX_JUMBO_RCV_DESCRIPTORS 1024
-#define MAX_LRO_RCV_DESCRIPTORS 64
+#define MAX_CMD_DESCRIPTORS_HOST 1024
+#define MAX_RCV_DESCRIPTORS_1G 2048
+#define MAX_RCV_DESCRIPTORS_10G 4096
+#define MAX_JUMBO_RCV_DESCRIPTORS 512
+#define MAX_LRO_RCV_DESCRIPTORS 8
#define MAX_RCVSTATUS_DESCRIPTORS MAX_RCV_DESCRIPTORS
#define MAX_JUMBO_RCV_DESC MAX_JUMBO_RCV_DESCRIPTORS
#define MAX_RCV_DESC MAX_RCV_DESCRIPTORS
}
ring->tx_pending = adapter->max_tx_desc_count;
- ring->rx_max_pending = MAX_RCV_DESCRIPTORS;
+ if (adapter->ahw.board_type == NETXEN_NIC_GBE)
+ ring->rx_max_pending = MAX_RCV_DESCRIPTORS_1G;
+ else
+ ring->rx_max_pending = MAX_RCV_DESCRIPTORS_10G;
ring->tx_max_pending = MAX_CMD_DESCRIPTORS_HOST;
ring->rx_jumbo_max_pending = MAX_JUMBO_RCV_DESCRIPTORS;
ring->rx_mini_max_pending = 0;
SET_ETHTOOL_OPS(netdev, &netxen_nic_ethtool_ops);
- /* ScatterGather support */
- netdev->features = NETIF_F_SG;
- netdev->features |= NETIF_F_IP_CSUM;
- netdev->features |= NETIF_F_TSO;
+ netdev->features |= (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO);
+ netdev->vlan_features |= (NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO);
+
if (NX_IS_REVISION_P3(revision_id)) {
- netdev->features |= NETIF_F_IPV6_CSUM;
- netdev->features |= NETIF_F_TSO6;
+ netdev->features |= (NETIF_F_IPV6_CSUM | NETIF_F_TSO6);
+ netdev->vlan_features |= (NETIF_F_IPV6_CSUM | NETIF_F_TSO6);
}
- if (adapter->pci_using_dac)
+ if (adapter->pci_using_dac) {
netdev->features |= NETIF_F_HIGHDMA;
+ netdev->vlan_features |= NETIF_F_HIGHDMA;
+ }
/*
* Set the CRB window to invalid. If any register in window 0 is
{
bool tso = false;
u8 opcode = TX_ETHER_PKT;
+ __be16 protocol = skb->protocol;
+ u16 flags = 0;
+
+ if (protocol == __constant_htons(ETH_P_8021Q)) {
+ struct vlan_ethhdr *vh = (struct vlan_ethhdr *)skb->data;
+ protocol = vh->h_vlan_encapsulated_proto;
+ flags = FLAGS_VLAN_TAGGED;
+ }
if ((netdev->features & (NETIF_F_TSO | NETIF_F_TSO6)) &&
skb_shinfo(skb)->gso_size > 0) {
desc->total_hdr_length =
skb_transport_offset(skb) + tcp_hdrlen(skb);
- opcode = (skb->protocol == htons(ETH_P_IPV6)) ?
+ opcode = (protocol == __constant_htons(ETH_P_IPV6)) ?
TX_TCP_LSO6 : TX_TCP_LSO;
tso = true;
} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
u8 l4proto;
- if (skb->protocol == htons(ETH_P_IP)) {
+ if (protocol == __constant_htons(ETH_P_IP)) {
l4proto = ip_hdr(skb)->protocol;
if (l4proto == IPPROTO_TCP)
opcode = TX_TCP_PKT;
else if(l4proto == IPPROTO_UDP)
opcode = TX_UDP_PKT;
- } else if (skb->protocol == htons(ETH_P_IPV6)) {
+ } else if (protocol == __constant_htons(ETH_P_IPV6)) {
l4proto = ipv6_hdr(skb)->nexthdr;
if (l4proto == IPPROTO_TCP)
}
desc->tcp_hdr_offset = skb_transport_offset(skb);
desc->ip_hdr_offset = skb_network_offset(skb);
- netxen_set_tx_flags_opcode(desc, 0, opcode);
+ netxen_set_tx_flags_opcode(desc, flags, opcode);
return tso;
}
struct phy_driver *phydrv = to_phy_driver(drv);
struct phy_device *phydev = to_phy_device(dev);
- if ((!device_may_wakeup(phydev->dev.parent)) &&
- (phydrv && phydrv->suspend))
- ret = phydrv->suspend(phydev);
+ if (drv && phydrv->suspend && !device_may_wakeup(phydev->dev.parent))
+ ret = phydrv->suspend(phydev);
return ret;
}
struct phy_driver *phydrv = to_phy_driver(drv);
struct phy_device *phydev = to_phy_device(dev);
- if ((!device_may_wakeup(phydev->dev.parent)) &&
- (phydrv && phydrv->resume))
+ if (drv && phydrv->resume && !device_may_wakeup(phydev->dev.parent))
ret = phydrv->resume(phydev);
return ret;
.ack_interrupt = smsc_phy_ack_interrupt,
.config_intr = smsc_phy_config_intr,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+
.driver = { .owner = THIS_MODULE, }
};
.ack_interrupt = smsc_phy_ack_interrupt,
.config_intr = smsc_phy_config_intr,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+
.driver = { .owner = THIS_MODULE, }
};
.ack_interrupt = smsc_phy_ack_interrupt,
.config_intr = smsc_phy_config_intr,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+
.driver = { .owner = THIS_MODULE, }
};
.ack_interrupt = smsc_phy_ack_interrupt,
.config_intr = smsc_phy_config_intr,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+
.driver = { .owner = THIS_MODULE, }
};
return err;
}
+static int tg3_request_firmware(struct tg3 *tp)
+{
+ const __be32 *fw_data;
+
+ if (request_firmware(&tp->fw, tp->fw_needed, &tp->pdev->dev)) {
+ printk(KERN_ERR "%s: Failed to load firmware \"%s\"\n",
+ tp->dev->name, tp->fw_needed);
+ return -ENOENT;
+ }
+
+ fw_data = (void *)tp->fw->data;
+
+ /* Firmware blob starts with version numbers, followed by
+ * start address and _full_ length including BSS sections
+ * (which must be longer than the actual data, of course
+ */
+
+ tp->fw_len = be32_to_cpu(fw_data[2]); /* includes bss */
+ if (tp->fw_len < (tp->fw->size - 12)) {
+ printk(KERN_ERR "%s: bogus length %d in \"%s\"\n",
+ tp->dev->name, tp->fw_len, tp->fw_needed);
+ release_firmware(tp->fw);
+ tp->fw = NULL;
+ return -EINVAL;
+ }
+
+ /* We no longer need firmware; we have it. */
+ tp->fw_needed = NULL;
+ return 0;
+}
+
static int tg3_open(struct net_device *dev)
{
struct tg3 *tp = netdev_priv(dev);
int err;
+ if (tp->fw_needed) {
+ err = tg3_request_firmware(tp);
+ if (tp->pci_chip_rev_id == CHIPREV_ID_5701_A0) {
+ if (err)
+ return err;
+ } else if (err) {
+ printk(KERN_WARNING "%s: TSO capability disabled.\n",
+ tp->dev->name);
+ tp->tg3_flags2 &= ~TG3_FLG2_TSO_CAPABLE;
+ } else if (!(tp->tg3_flags2 & TG3_FLG2_TSO_CAPABLE)) {
+ printk(KERN_NOTICE "%s: TSO capability restored.\n",
+ tp->dev->name);
+ tp->tg3_flags2 |= TG3_FLG2_TSO_CAPABLE;
+ }
+ }
+
netif_carrier_off(tp->dev);
err = tg3_set_power_state(tp, PCI_D0);
struct net_device *dev;
struct tg3 *tp;
int err, pm_cap;
- const char *fw_name = NULL;
char str[40];
u64 dma_mask, persist_dma_mask;
tg3_init_bufmgr_config(tp);
if (tp->pci_chip_rev_id == CHIPREV_ID_5701_A0)
- fw_name = FIRMWARE_TG3;
+ tp->fw_needed = FIRMWARE_TG3;
if (tp->tg3_flags2 & TG3_FLG2_HW_TSO) {
tp->tg3_flags2 |= TG3_FLG2_TSO_CAPABLE;
tp->tg3_flags2 &= ~TG3_FLG2_TSO_CAPABLE;
} else {
tp->tg3_flags2 |= TG3_FLG2_TSO_CAPABLE | TG3_FLG2_TSO_BUG;
- }
- if (tp->tg3_flags2 & TG3_FLG2_TSO_CAPABLE) {
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5705)
- fw_name = FIRMWARE_TG3TSO5;
+ tp->fw_needed = FIRMWARE_TG3TSO5;
else
- fw_name = FIRMWARE_TG3TSO;
- }
-
- if (fw_name) {
- const __be32 *fw_data;
-
- err = request_firmware(&tp->fw, fw_name, &tp->pdev->dev);
- if (err) {
- printk(KERN_ERR "tg3: Failed to load firmware \"%s\"\n",
- fw_name);
- goto err_out_iounmap;
- }
-
- fw_data = (void *)tp->fw->data;
-
- /* Firmware blob starts with version numbers, followed by
- start address and _full_ length including BSS sections
- (which must be longer than the actual data, of course */
-
- tp->fw_len = be32_to_cpu(fw_data[2]); /* includes bss */
- if (tp->fw_len < (tp->fw->size - 12)) {
- printk(KERN_ERR "tg3: bogus length %d in \"%s\"\n",
- tp->fw_len, fw_name);
- err = -EINVAL;
- goto err_out_fw;
- }
+ tp->fw_needed = FIRMWARE_TG3TSO;
}
/* TSO is on by default on chips that support hardware TSO.
struct ethtool_coalesce coal;
/* firmware info */
+ const char *fw_needed;
const struct firmware *fw;
u32 fw_len; /* includes BSS */
};
{
struct usb_device *xdev = dev->udev;
int ret;
+ void *buffer;
+
+ buffer = kmalloc(size, GFP_NOIO);
+ if (buffer == NULL)
+ return -ENOMEM;
ret = usb_control_msg(xdev, usb_rcvctrlpipe(xdev, 0), MCS7830_RD_BREQ,
- MCS7830_RD_BMREQ, 0x0000, index, data,
+ MCS7830_RD_BMREQ, 0x0000, index, buffer,
size, MCS7830_CTRL_TIMEOUT);
+ memcpy(data, buffer, size);
+ kfree(buffer);
+
return ret;
}
{
struct usb_device *xdev = dev->udev;
int ret;
+ void *buffer;
+
+ buffer = kmalloc(size, GFP_NOIO);
+ if (buffer == NULL)
+ return -ENOMEM;
+
+ memcpy(buffer, data, size);
ret = usb_control_msg(xdev, usb_sndctrlpipe(xdev, 0), MCS7830_WR_BREQ,
- MCS7830_WR_BMREQ, 0x0000, index, data,
+ MCS7830_WR_BMREQ, 0x0000, index, buffer,
size, MCS7830_CTRL_TIMEOUT);
+ kfree(buffer);
return ret;
}
static int velocity_init_td_ring(struct velocity_info *vptr)
{
dma_addr_t curr;
- unsigned int j;
+ int j;
/* Init the TD ring entries */
for (j = 0; j < vptr->tx.numq; j++) {
#include <linux/virtio.h>
#include <linux/virtio_net.h>
#include <linux/scatterlist.h>
+#include <linux/if_vlan.h>
static int napi_weight = 128;
module_param(napi_weight, int, 0444);
module_param(gso, bool, 0444);
/* FIXME: MTU in config. */
-#define MAX_PACKET_LEN (ETH_HLEN+ETH_DATA_LEN)
+#define MAX_PACKET_LEN (ETH_HLEN + VLAN_HLEN + ETH_DATA_LEN)
#define GOOD_COPY_LEN 128
struct virtnet_info
spin_lock_irqsave(&i2400m->rx_lock, flags);
ack_skb = i2400m->ack_skb;
if (ack_skb && !IS_ERR(ack_skb))
- kfree(ack_skb);
+ kfree_skb(ack_skb);
i2400m->ack_skb = ERR_PTR(code);
spin_unlock_irqrestore(&i2400m->rx_lock, flags);
}
* NOTE: this function might realloc the skb (if it is too small),
* so always update with the one returned.
* ERR_PTR() is < 0 on error.
+ * Will return NULL if it cannot reallocate -- this can be
+ * considered a transient retryable error.
*/
static
struct sk_buff *i2400mu_rx(struct i2400mu *i2400mu, struct sk_buff *rx_skb)
if (printk_ratelimit())
dev_err(dev, "RX: Can't reallocate skb to %d; "
"RX dropped\n", rx_size);
- kfree(rx_skb);
- result = 0;
+ kfree_skb(rx_skb);
+ rx_skb = NULL;
goto out; /* drop it...*/
}
kfree_skb(rx_skb);
if (IS_ERR(rx_skb))
goto out;
atomic_dec(&i2400mu->rx_pending_count);
- if (rx_skb->len == 0) { /* some ignorable condition */
+ if (rx_skb == NULL || rx_skb->len == 0) {
+ /* some "ignorable" condition */
kfree_skb(rx_skb);
continue;
}
static int ath_rc_valid_phyrate(u32 phy, u32 capflag, int ignore_cw)
{
- if (WLAN_RC_PHY_HT(phy) & !(capflag & WLAN_RC_HT_FLAG))
+ if (WLAN_RC_PHY_HT(phy) && !(capflag & WLAN_RC_HT_FLAG))
return 0;
if (WLAN_RC_PHY_DS(phy) && !(capflag & WLAN_RC_DS_FLAG))
return 0;
};
#define REG_DOMAIN_2GHZ_MASK (REQ_MASK & \
- (!(ADHOC_NO_11A | DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB)))
+ (~(ADHOC_NO_11A | DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB)))
#define REG_DOMAIN_5GHZ_MASK REQ_MASK
static struct reg_dmn_pair_mapping regDomainPairs[] = {
s8 scale_action = 0;
unsigned long flags;
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
- u16 fc, rate_mask;
+ u16 fc;
+ u16 rate_mask = 0;
struct iwl3945_priv *priv = (struct iwl3945_priv *)priv_r;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
IWL_DEBUG_RATE("enter\n");
+ if (sta)
+ rate_mask = sta->supp_rates[sband->band];
+
/* Send management frames and broadcast/multicast data using lowest
* rate. */
fc = le16_to_cpu(hdr->frame_control);
is_multicast_ether_addr(hdr->addr1) ||
!sta || !priv_sta) {
IWL_DEBUG_RATE("leave: No STA priv data to update!\n");
- info->control.rates[0].idx = rate_lowest_index(sband, sta);
+ if (!rate_mask)
+ info->control.rates[0].idx =
+ rate_lowest_index(sband, NULL);
+ else
+ info->control.rates[0].idx =
+ rate_lowest_index(sband, sta);
return;
}
- rate_mask = sta->supp_rates[sband->band];
index = min(rs_sta->last_txrate_idx & 0xffff, IWL_RATE_COUNT - 1);
if (sband->band == IEEE80211_BAND_5GHZ)
}
/* See if there's a better rate or modulation mode to try. */
- rs_rate_scale_perform(priv, hdr, sta, lq_sta);
+ if (sta && sta->supp_rates[sband->band])
+ rs_rate_scale_perform(priv, hdr, sta, lq_sta);
out:
return;
}
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct iwl_lq_sta *lq_sta = priv_sta;
int rate_idx;
+ u64 mask_bit = 0;
IWL_DEBUG_RATE_LIMIT("rate scale calculate new rate for skb\n");
+ if (sta)
+ mask_bit = sta->supp_rates[sband->band];
+
/* Send management frames and broadcast/multicast data using lowest
* rate. */
if (!ieee80211_is_data(hdr->frame_control) ||
is_multicast_ether_addr(hdr->addr1) || !sta || !lq_sta) {
- info->control.rates[0].idx = rate_lowest_index(sband, sta);
+ if (!mask_bit)
+ info->control.rates[0].idx =
+ rate_lowest_index(sband, NULL);
+ else
+ info->control.rates[0].idx =
+ rate_lowest_index(sband, sta);
return;
}
dev_kfree_skb_any(skb);
IWL_DEBUG_MACDUMP("leave\n");
- return 0;
+ return NETDEV_TX_OK;
}
static int iwl_mac_add_interface(struct ieee80211_hw *hw,
IWL_ERROR("Error: Response NULL in '%s'\n",
get_cmd_string(cmd->id));
ret = -EIO;
- goto out;
+ goto cancel;
}
ret = 0;
IWL_ERROR("Error: Response NULL in '%s'\n",
get_cmd_string(cmd->id));
ret = -EIO;
- goto out;
+ goto cancel;
}
ret = 0;
dev_kfree_skb_any(skb);
IWL_DEBUG_MAC80211("leave\n");
- return 0;
+ return NETDEV_TX_OK;
}
static int iwl3945_mac_add_interface(struct ieee80211_hw *hw,
u8 pktdelay_2ms;
/* reserved */
u8 reserved1;
-};
+} __attribute__ ((packed));
/* RxPD Descriptor */
struct rxpd {
/* Pkt Priority */
u8 priority;
u8 reserved[3];
-};
+} __attribute__ ((packed));
struct cmd_header {
__le16 command;
struct lbs_offset_value {
u32 offset;
u32 value;
-};
+} __attribute__ ((packed));
/* Define general data structure */
/* cmd_DS_GEN */
__le16 seqnum;
__le16 result;
void *cmdresp[0];
-};
+} __attribute__ ((packed));
#define S_DS_GEN sizeof(struct cmd_ds_gen)
* bump this up a bit.
*/
uint8_t tlv[128];
-};
+} __attribute__ ((packed));
/*
* This scan handle Country Information IE(802.11d compliant)
mrvlietypes_chanlistparamset_t ChanListParamSet;
mrvlietypes_ratesparamset_t OpRateSet;
#endif
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_scan_rsp {
struct cmd_header hdr;
__le16 bssdescriptsize;
uint8_t nr_sets;
uint8_t bssdesc_and_tlvbuffer[0];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_get_log {
struct cmd_header hdr;
__le32 fcserror;
__le32 txframe;
__le32 wepundecryptable;
-};
+} __attribute__ ((packed));
struct cmd_ds_mac_control {
struct cmd_header hdr;
__le16 action;
u16 reserved;
-};
+} __attribute__ ((packed));
struct cmd_ds_mac_multicast_adr {
struct cmd_header hdr;
__le16 action;
__le16 nr_of_adrs;
u8 maclist[ETH_ALEN * MRVDRV_MAX_MULTICAST_LIST_SIZE];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_authenticate {
u8 macaddr[ETH_ALEN];
u8 authtype;
u8 reserved[10];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_deauthenticate {
struct cmd_header hdr;
u8 macaddr[ETH_ALEN];
__le16 reasoncode;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_associate {
u8 peerstaaddr[6];
struct cmd_ds_802_11_associate_rsp {
struct ieeetypes_assocrsp assocRsp;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_set_wep {
struct cmd_header hdr;
/* 40, 128bit or TXWEP */
uint8_t keytype[4];
uint8_t keymaterial[4][16];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_3_get_stat {
__le32 xmitok;
__le32 rcverror;
__le32 rcvnobuffer;
__le32 rcvcrcerror;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_get_stat {
__le32 txfragmentcnt;
__le32 txbeacon;
__le32 rxbeacon;
__le32 wepundecryptable;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_snmp_mib {
struct cmd_header hdr;
__le16 oid;
__le16 bufsize;
u8 value[128];
-};
+} __attribute__ ((packed));
struct cmd_ds_mac_reg_map {
__le16 buffersize;
u8 regmap[128];
__le16 reserved;
-};
+} __attribute__ ((packed));
struct cmd_ds_bbp_reg_map {
__le16 buffersize;
u8 regmap[128];
__le16 reserved;
-};
+} __attribute__ ((packed));
struct cmd_ds_rf_reg_map {
__le16 buffersize;
u8 regmap[64];
__le16 reserved;
-};
+} __attribute__ ((packed));
struct cmd_ds_mac_reg_access {
__le16 action;
__le16 offset;
__le32 value;
-};
+} __attribute__ ((packed));
struct cmd_ds_bbp_reg_access {
__le16 action;
__le16 offset;
u8 value;
u8 reserved[3];
-};
+} __attribute__ ((packed));
struct cmd_ds_rf_reg_access {
__le16 action;
__le16 offset;
u8 value;
u8 reserved[3];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_radio_control {
struct cmd_header hdr;
__le16 action;
__le16 control;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_beacon_control {
__le16 action;
__le16 beacon_enable;
__le16 beacon_period;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_sleep_params {
struct cmd_header hdr;
/* reserved field, should be set to zero */
__le16 reserved;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_inactivity_timeout {
struct cmd_header hdr;
/* Inactivity timeout in msec */
__le16 timeout;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rf_channel {
struct cmd_header hdr;
__le16 rftype; /* unused */
__le16 reserved; /* unused */
u8 channellist[32]; /* unused */
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rssi {
/* weighting factor */
__le16 reserved_0;
__le16 reserved_1;
__le16 reserved_2;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rssi_rsp {
__le16 SNR;
__le16 noisefloor;
__le16 avgSNR;
__le16 avgnoisefloor;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_mac_address {
struct cmd_header hdr;
__le16 action;
u8 macadd[ETH_ALEN];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rf_tx_power {
struct cmd_header hdr;
__le16 curlevel;
s8 maxlevel;
s8 minlevel;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rf_antenna {
__le16 action;
/* Number of antennas or 0xffff(diversity) */
__le16 antennamode;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_monitor_mode {
__le16 action;
__le16 mode;
-};
+} __attribute__ ((packed));
struct cmd_ds_set_boot2_ver {
struct cmd_header hdr;
__le16 action;
__le16 version;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_fw_wake_method {
struct cmd_header hdr;
__le16 action;
__le16 method;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_sleep_period {
struct cmd_header hdr;
__le16 action;
__le16 period;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_ps_mode {
__le16 action;
__le16 multipledtim;
__le16 reserved;
__le16 locallisteninterval;
-};
+} __attribute__ ((packed));
struct cmd_confirm_sleep {
struct cmd_header hdr;
__le16 multipledtim;
__le16 reserved;
__le16 locallisteninterval;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_data_rate {
struct cmd_header hdr;
__le16 action;
__le16 reserved;
u8 rates[MAX_RATES];
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_rate_adapt_rateset {
struct cmd_header hdr;
__le16 action;
__le16 enablehwauto;
__le16 bitmap;
-};
+} __attribute__ ((packed));
struct cmd_ds_802_11_ad_hoc_start {
struct cmd_header hdr;
u8 pad[3];
u8 bssid[ETH_ALEN];
-};
+} __attribute__ ((packed));
struct adhoc_bssdesc {
u8 bssid[ETH_ALEN];
/* key material of size keylen */
u8 key[32];
-};
+} __attribute__ ((packed));
#define MAX_WOL_RULES 16
__le16 reserve;
__be32 sig_mask;
__be32 signature;
-};
+} __attribute__ ((packed));
struct wol_config {
uint8_t action;
uint8_t no_rules_in_cmd;
uint8_t result;
struct host_wol_rule rule[MAX_WOL_RULES];
-};
-
+} __attribute__ ((packed));
struct cmd_ds_host_sleep {
struct cmd_header hdr;
s = "UNKNOWN";
}
- printk(KERN_INFO "%s: New link status: %s (%04x)\n",
+ printk(KERN_DEBUG "%s: New link status: %s (%04x)\n",
dev->name, s, status);
}
struct orinoco_private *priv = netdev_priv(dev);
u8 *buf;
unsigned long flags;
- int err = 0;
/* cut off at IEEE80211_MAX_DATA_LEN */
if ((wrqu->data.length > IEEE80211_MAX_DATA_LEN) ||
(wrqu->data.length && (extra == NULL)))
return -EINVAL;
- if (orinoco_lock(priv, &flags) != 0)
- return -EBUSY;
-
if (wrqu->data.length) {
buf = kmalloc(wrqu->data.length, GFP_KERNEL);
- if (buf == NULL) {
- err = -ENOMEM;
- goto out;
- }
+ if (buf == NULL)
+ return -ENOMEM;
memcpy(buf, extra, wrqu->data.length);
- kfree(priv->wpa_ie);
- priv->wpa_ie = buf;
- priv->wpa_ie_len = wrqu->data.length;
- } else {
- kfree(priv->wpa_ie);
- priv->wpa_ie = NULL;
- priv->wpa_ie_len = 0;
+ } else
+ buf = NULL;
+
+ if (orinoco_lock(priv, &flags) != 0) {
+ kfree(buf);
+ return -EBUSY;
}
+ kfree(priv->wpa_ie);
+ priv->wpa_ie = buf;
+ priv->wpa_ie_len = wrqu->data.length;
+
if (priv->wpa_ie) {
/* Looks like wl_lkm wants to check the auth alg, and
* somehow pass it to the firmware.
*/
}
-out:
orinoco_unlock(priv, &flags);
- return err;
+ return 0;
}
static int orinoco_ioctl_get_genie(struct net_device *dev,
}
if (err)
goto err;
-
- }
+ }
+ break;
case PDR_PRISM_ZIF_TX_IQ_CALIBRATION:
priv->iq_autocal = kmalloc(data_len, GFP_KERNEL);
if (!priv->iq_autocal) {
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(entry);
struct p54_hdr *entry_hdr;
struct p54_tx_data *entry_data;
- int pad = 0;
+ unsigned int pad = 0, frame_len;
range = (void *)info->rate_driver_data;
if (range->start_addr != addr) {
__skb_unlink(entry, &priv->tx_queue);
spin_unlock_irqrestore(&priv->tx_queue.lock, flags);
+ frame_len = entry->len;
entry_hdr = (struct p54_hdr *) entry->data;
entry_data = (struct p54_tx_data *) entry_hdr->data;
priv->tx_stats[entry_data->hw_queue].len--;
info->status.ack_signal = p54_rssi_to_dbm(dev,
(int)payload->ack_rssi);
- if (entry_data->key_type == P54_CRYPTO_TKIPMICHAEL) {
+ /* Undo all changes to the frame. */
+ switch (entry_data->key_type) {
+ case P54_CRYPTO_TKIPMICHAEL: {
u8 *iv = (u8 *)(entry_data->align + pad +
- entry_data->crypt_offset);
+ entry_data->crypt_offset);
/* Restore the original TKIP IV. */
iv[2] = iv[0];
iv[0] = iv[1];
iv[1] = (iv[0] | 0x20) & 0x7f; /* WEPSeed - 8.3.2.2 */
+
+ frame_len -= 12; /* remove TKIP_MMIC + TKIP_ICV */
+ break;
+ }
+ case P54_CRYPTO_AESCCMP:
+ frame_len -= 8; /* remove CCMP_MIC */
+ break;
+ case P54_CRYPTO_WEP:
+ frame_len -= 4; /* remove WEP_ICV */
+ break;
}
+ skb_trim(entry, frame_len);
skb_pull(entry, sizeof(*hdr) + pad + sizeof(*entry_data));
ieee80211_tx_status_irqsafe(dev, entry);
goto out;
skb = p54_alloc_skb(dev, P54_HDR_FLAG_CONTROL_OPSET,
sizeof(struct p54_hdr) + sizeof(*tim),
- P54_CONTROL_TYPE_TIM, GFP_KERNEL);
+ P54_CONTROL_TYPE_TIM, GFP_ATOMIC);
if (!skb)
return -ENOMEM;
err:
printk(KERN_ERR "%s: frequency change failed\n", wiphy_name(dev->wiphy));
- kfree_skb(skb);
+ p54_free_skb(dev, skb);
return -EINVAL;
}
algo = P54_CRYPTO_AESCCMP;
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
}
struct sk_buff *skb = urb->context;
struct ieee80211_hw *dev = (struct ieee80211_hw *)
usb_get_intfdata(usb_ifnum_to_if(urb->dev, 0));
- struct p54u_priv *priv = dev->priv;
- skb_pull(skb, priv->common.tx_hdr_len);
- if (FREE_AFTER_TX(skb))
- p54_free_skb(dev, skb);
+ p54_free_skb(dev, skb);
}
static void p54u_tx_dummy_cb(struct urb *urb) { }
p54u_tx_dummy_cb, dev);
usb_fill_bulk_urb(data_urb, priv->udev,
usb_sndbulkpipe(priv->udev, P54U_PIPE_DATA),
- skb->data, skb->len, p54u_tx_cb, skb);
+ skb->data, skb->len, FREE_AFTER_TX(skb) ?
+ p54u_tx_cb : p54u_tx_dummy_cb, skb);
+ addr_urb->transfer_flags |= URB_ZERO_PACKET;
+ data_urb->transfer_flags |= URB_ZERO_PACKET;
usb_anchor_urb(addr_urb, &priv->submitted);
err = usb_submit_urb(addr_urb, GFP_ATOMIC);
goto out;
}
- usb_anchor_urb(addr_urb, &priv->submitted);
+ usb_anchor_urb(data_urb, &priv->submitted);
err = usb_submit_urb(data_urb, GFP_ATOMIC);
if (err)
usb_unanchor_urb(data_urb);
{
struct p54u_priv *priv = dev->priv;
struct urb *data_urb;
- struct lm87_tx_hdr *hdr;
- __le32 checksum;
- __le32 addr = ((struct p54_hdr *)skb->data)->req_id;
+ struct lm87_tx_hdr *hdr = (void *)skb->data - sizeof(*hdr);
data_urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!data_urb)
return;
- checksum = p54u_lm87_chksum((__le32 *)skb->data, skb->len);
- hdr = (struct lm87_tx_hdr *)skb_push(skb, sizeof(*hdr));
- hdr->chksum = checksum;
- hdr->device_addr = addr;
+ hdr->chksum = p54u_lm87_chksum((__le32 *)skb->data, skb->len);
+ hdr->device_addr = ((struct p54_hdr *)skb->data)->req_id;
usb_fill_bulk_urb(data_urb, priv->udev,
usb_sndbulkpipe(priv->udev, P54U_PIPE_DATA),
- skb->data, skb->len, p54u_tx_cb, skb);
+ hdr, skb->len + sizeof(*hdr), FREE_AFTER_TX(skb) ?
+ p54u_tx_cb : p54u_tx_dummy_cb, skb);
data_urb->transfer_flags |= URB_ZERO_PACKET;
usb_anchor_urb(data_urb, &priv->submitted);
if (usb_submit_urb(data_urb, GFP_ATOMIC)) {
usb_unanchor_urb(data_urb);
- skb_pull(skb, sizeof(*hdr));
p54_free_skb(dev, skb);
}
usb_free_urb(data_urb);
{
struct p54u_priv *priv = dev->priv;
struct urb *int_urb, *data_urb;
- struct net2280_tx_hdr *hdr;
+ struct net2280_tx_hdr *hdr = (void *)skb->data - sizeof(*hdr);
struct net2280_reg_write *reg;
int err = 0;
- __le32 addr = ((struct p54_hdr *) skb->data)->req_id;
- __le16 len = cpu_to_le16(skb->len);
reg = kmalloc(sizeof(*reg), GFP_ATOMIC);
if (!reg)
reg->addr = cpu_to_le32(P54U_DEV_BASE);
reg->val = cpu_to_le32(ISL38XX_DEV_INT_DATA);
- hdr = (void *)skb_push(skb, sizeof(*hdr));
memset(hdr, 0, sizeof(*hdr));
- hdr->len = len;
- hdr->device_addr = addr;
+ hdr->len = cpu_to_le16(skb->len);
+ hdr->device_addr = ((struct p54_hdr *) skb->data)->req_id;
usb_fill_bulk_urb(int_urb, priv->udev,
usb_sndbulkpipe(priv->udev, P54U_PIPE_DEV), reg, sizeof(*reg),
* free what's inside the transfer_buffer after the callback routine
* has completed.
*/
- int_urb->transfer_flags |= URB_FREE_BUFFER;
+ int_urb->transfer_flags |= URB_FREE_BUFFER | URB_ZERO_PACKET;
usb_fill_bulk_urb(data_urb, priv->udev,
usb_sndbulkpipe(priv->udev, P54U_PIPE_DATA),
- skb->data, skb->len, p54u_tx_cb, skb);
+ hdr, skb->len + sizeof(*hdr), FREE_AFTER_TX(skb) ?
+ p54u_tx_cb : p54u_tx_dummy_cb, skb);
+ data_urb->transfer_flags |= URB_ZERO_PACKET;
usb_anchor_urb(int_urb, &priv->submitted);
err = usb_submit_urb(int_urb, GFP_ATOMIC);
char *end_buf,
struct ndis_80211_bssid_ex *bssid)
{
-#ifdef DEBUG
struct usbnet *usbdev = netdev_priv(dev);
-#endif
u8 *ie;
char *current_val;
int bssid_len, ie_len, i;
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
+ struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
struct ieee80211_rate *rate =
ieee80211_get_tx_rate(rt2x00dev->hw, tx_info);
const struct rt2x00_rate *hwrate;
* When preamble is enabled we should set the
* preamble bit for the signal.
*/
- if (rate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
+ if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
txdesc->signal |= 0x08;
}
}
void rt2x00rfkill_free(struct rt2x00_dev *rt2x00dev)
{
- if (!test_bit(RFKILL_STATE_ALLOCATED, &rt2x00dev->flags))
+ if (!test_bit(RFKILL_STATE_ALLOCATED, &rt2x00dev->rfkill_state))
return;
cancel_delayed_work_sync(&rt2x00dev->rfkill_work);
usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep),
buf, skb->len, rtl8187_tx_cb, skb);
+ urb->transfer_flags |= URB_ZERO_PACKET;
usb_anchor_urb(urb, &priv->anchored);
rc = usb_submit_urb(urb, GFP_ATOMIC);
if (rc < 0) {
{ USB_DEVICE(0x0586, 0x340a), .driver_info = DEVICE_ZD1211B },
{ USB_DEVICE(0x0471, 0x1237), .driver_info = DEVICE_ZD1211B },
{ USB_DEVICE(0x07fa, 0x1196), .driver_info = DEVICE_ZD1211B },
+ { USB_DEVICE(0x0df6, 0x0036), .driver_info = DEVICE_ZD1211B },
/* "Driverless" devices that need ejecting */
{ USB_DEVICE(0x0ace, 0x2011), .driver_info = DEVICE_INSTALLER },
{ USB_DEVICE(0x0ace, 0x20ff), .driver_info = DEVICE_INSTALLER },
static void lcs_tasklet(unsigned long);
static void lcs_start_kernel_thread(struct work_struct *);
static void lcs_get_frames_cb(struct lcs_channel *, struct lcs_buffer *);
+#ifdef CONFIG_IP_MULTICAST
static int lcs_send_delipm(struct lcs_card *, struct lcs_ipm_list *);
+#endif /* CONFIG_IP_MULTICAST */
static int lcs_recovery(void *ptr);
/**
lcs_clear_thread_running_bit(card, LCS_SET_MC_THREAD);
return 0;
}
+#endif /* CONFIG_IP_MULTICAST */
+
/**
* function called by net device to
* handle multicast address relevant things
static void
lcs_set_multicast_list(struct net_device *dev)
{
+#ifdef CONFIG_IP_MULTICAST
struct lcs_card *card;
LCS_DBF_TEXT(4, trace, "setmulti");
if (!lcs_set_thread_start_bit(card, LCS_SET_MC_THREAD))
schedule_work(&card->kernel_thread_starter);
-}
-
#endif /* CONFIG_IP_MULTICAST */
+}
static long
lcs_check_irb_error(struct ccw_device *cdev, struct irb *irb)
#include <linux/if.h>
-#if defined(CONFIG_DLCI) || defined(CONFIG_DLCI_MODULE)
-
/* Structures and constants associated with the DLCI device driver */
struct dlci_add
#ifdef __KERNEL__
+#if defined(CONFIG_DLCI) || defined(CONFIG_DLCI_MODULE)
+
/* these are the fields of an RFC 1490 header */
struct frhdr
{
int buffer; /* current buffer for S508 firmware */
};
-#endif /* __KERNEL__ */
-
#endif /* CONFIG_DLCI || CONFIG_DLCI_MODULE */
-#ifdef __KERNEL__
extern void dlci_ioctl_set(int (*hook)(unsigned int, void __user *));
-#endif
+
+#endif /* __KERNEL__ */
#endif
#define devdbg(usbnet, fmt, arg...) \
printk(KERN_DEBUG "%s: " fmt "\n" , (usbnet)->net->name , ## arg)
#else
-#define devdbg(usbnet, fmt, arg...) do {} while(0)
+#define devdbg(usbnet, fmt, arg...) \
+ ({ if (0) printk(KERN_DEBUG "%s: " fmt "\n" , (usbnet)->net->name , \
+ ## arg); 0; })
#endif
#define deverr(usbnet, fmt, arg...) \
* @control: union for control data
* @status: union for status data
* @driver_data: array of driver_data pointers
- * @retry_count: number of retries
* @ampdu_ack_len: number of aggregated frames.
* relevant only if IEEE80211_TX_STATUS_AMPDU was set.
* @ampdu_ack_map: block ack bit map for the aggregation.
static inline __be32 sctp_end_cksum(__be32 crc32)
{
- return ~crc32;
+ return (__force __be32)~cpu_to_le32((__force u32)crc32);
}
Unless you want to work with an experimental feature
say N here.
+config NET_NS
+ bool "Network namespace"
+ default n
+ depends on NAMESPACES && EXPERIMENTAL && NET
+ help
+ Allow user space to create what appear to be multiple instances
+ of the network stack.
+
config BLK_DEV_INITRD
bool "Initial RAM filesystem and RAM disk (initramfs/initrd) support"
depends on BROKEN || !FRV
{
return vlan_dev_info(dev)->real_dev;
}
-EXPORT_SYMBOL_GPL(vlan_dev_real_dev);
+EXPORT_SYMBOL(vlan_dev_real_dev);
u16 vlan_dev_vlan_id(const struct net_device *dev)
{
return vlan_dev_info(dev)->vlan_id;
}
-EXPORT_SYMBOL_GPL(vlan_dev_vlan_id);
+EXPORT_SYMBOL(vlan_dev_vlan_id);
static int vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp,
unsigned int vlan_tci, struct sk_buff *skb)
return ERR_PTR(-ENOMEM);
ret = p9_idpool_get(clnt->fidpool);
- if (fid->fid < 0) {
+ if (ret < 0) {
ret = -ENOSPC;
goto error;
}
menu "Networking options"
-config NET_NS
- bool "Network namespace support"
- default n
- depends on EXPERIMENTAL && NAMESPACES
- help
- Allow user space to create what appear to be multiple instances
- of the network stack.
-
config COMPAT_NET_DEV_OPS
def_bool y
skb->mac_len = skb->network_header - skb->mac_header;
__skb_pull(skb, skb->mac_len);
- if (WARN_ON(skb->ip_summed != CHECKSUM_PARTIAL)) {
+ if (unlikely(skb->ip_summed != CHECKSUM_PARTIAL)) {
+ struct net_device *dev = skb->dev;
+ struct ethtool_drvinfo info = {};
+
+ if (dev && dev->ethtool_ops && dev->ethtool_ops->get_drvinfo)
+ dev->ethtool_ops->get_drvinfo(dev, &info);
+
+ WARN(1, "%s: caps=(0x%lx, 0x%lx) len=%d data_len=%d "
+ "ip_summed=%d",
+ info.driver, dev ? dev->features : 0L,
+ skb->sk ? skb->sk->sk_route_caps : 0L,
+ skb->len, skb->data_len, skb->ip_summed);
+
if (skb_header_cloned(skb) &&
(err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC)))
return ERR_PTR(err);
if (!pskb_may_pull(skb, ETH_HLEN)) {
napi_reuse_skb(napi, skb);
+ skb = NULL;
goto out;
}
rv = register_pernet_operations(first_device, ops);
if (rv < 0)
ida_remove(&net_generic_ids, *id);
- mutex_unlock(&net_mutex);
out:
+ mutex_unlock(&net_mutex);
return rv;
}
EXPORT_SYMBOL_GPL(register_pernet_gen_subsys);
static void sock_pipe_buf_release(struct pipe_inode_info *pipe,
struct pipe_buffer *buf)
{
- struct sk_buff *skb = (struct sk_buff *) buf->private;
-
- kfree_skb(skb);
+ put_page(buf->page);
}
static void sock_pipe_buf_get(struct pipe_inode_info *pipe,
struct pipe_buffer *buf)
{
- struct sk_buff *skb = (struct sk_buff *) buf->private;
-
- skb_get(skb);
+ get_page(buf->page);
}
static int sock_pipe_buf_steal(struct pipe_inode_info *pipe,
*/
static void sock_spd_release(struct splice_pipe_desc *spd, unsigned int i)
{
- struct sk_buff *skb = (struct sk_buff *) spd->partial[i].private;
+ put_page(spd->pages[i]);
+}
- kfree_skb(skb);
+static inline struct page *linear_to_page(struct page *page, unsigned int len,
+ unsigned int offset)
+{
+ struct page *p = alloc_pages(GFP_KERNEL, 0);
+
+ if (!p)
+ return NULL;
+ memcpy(page_address(p) + offset, page_address(page) + offset, len);
+
+ return p;
}
/*
*/
static inline int spd_fill_page(struct splice_pipe_desc *spd, struct page *page,
unsigned int len, unsigned int offset,
- struct sk_buff *skb)
+ struct sk_buff *skb, int linear)
{
if (unlikely(spd->nr_pages == PIPE_BUFFERS))
return 1;
+ if (linear) {
+ page = linear_to_page(page, len, offset);
+ if (!page)
+ return 1;
+ } else
+ get_page(page);
+
spd->pages[spd->nr_pages] = page;
spd->partial[spd->nr_pages].len = len;
spd->partial[spd->nr_pages].offset = offset;
- spd->partial[spd->nr_pages].private = (unsigned long) skb_get(skb);
spd->nr_pages++;
+
return 0;
}
static inline int __splice_segment(struct page *page, unsigned int poff,
unsigned int plen, unsigned int *off,
unsigned int *len, struct sk_buff *skb,
- struct splice_pipe_desc *spd)
+ struct splice_pipe_desc *spd, int linear)
{
if (!*len)
return 1;
/* the linear region may spread across several pages */
flen = min_t(unsigned int, flen, PAGE_SIZE - poff);
- if (spd_fill_page(spd, page, flen, poff, skb))
+ if (spd_fill_page(spd, page, flen, poff, skb, linear))
return 1;
__segment_seek(&page, &poff, &plen, flen);
if (__splice_segment(virt_to_page(skb->data),
(unsigned long) skb->data & (PAGE_SIZE - 1),
skb_headlen(skb),
- offset, len, skb, spd))
+ offset, len, skb, spd, 1))
return 1;
/*
const skb_frag_t *f = &skb_shinfo(skb)->frags[seg];
if (__splice_segment(f->page, f->page_offset, f->size,
- offset, len, skb, spd))
+ offset, len, skb, spd, 0))
return 1;
}
* the frag list, if such a thing exists. We'd probably need to recurse to
* handle that cleanly.
*/
-int skb_splice_bits(struct sk_buff *__skb, unsigned int offset,
+int skb_splice_bits(struct sk_buff *skb, unsigned int offset,
struct pipe_inode_info *pipe, unsigned int tlen,
unsigned int flags)
{
.ops = &sock_pipe_buf_ops,
.spd_release = sock_spd_release,
};
- struct sk_buff *skb;
-
- /*
- * I'd love to avoid the clone here, but tcp_read_sock()
- * ignores reference counts and unconditonally kills the sk_buff
- * on return from the actor.
- */
- skb = skb_clone(__skb, GFP_KERNEL);
- if (unlikely(!skb))
- return -ENOMEM;
/*
* __skb_splice_bits() only fails if the output has no room left,
}
done:
- /*
- * drop our reference to the clone, the pipe consumption will
- * drop the rest.
- */
- kfree_skb(skb);
-
if (spd.nr_pages) {
+ struct sock *sk = skb->sk;
int ret;
- struct sock *sk = __skb->sk;
/*
* Drop the socket lock, otherwise we have reverse
struct sk_buff *nskb;
unsigned int headroom;
unsigned int hlen = p->data - skb_mac_header(p);
+ unsigned int len = skb->len;
- if (hlen + p->len + skb->len >= 65536)
+ if (hlen + p->len + len >= 65536)
return -E2BIG;
if (skb_shinfo(p)->frag_list)
done:
NAPI_GRO_CB(p)->count++;
- p->data_len += skb->len;
- p->truesize += skb->len;
- p->len += skb->len;
+ p->data_len += len;
+ p->truesize += len;
+ p->len += len;
NAPI_GRO_CB(skb)->same_flow = 1;
return 0;
unsigned int nlen;
int flush = 1;
int proto;
+ __wsum csum;
if (unlikely(!pskb_may_pull(skb, sizeof(*iph))))
goto out;
rcu_read_lock();
proto = ipv6_gso_pull_exthdrs(skb, iph->nexthdr);
+ iph = ipv6_hdr(skb);
IPV6_GRO_CB(skb)->proto = proto;
ops = rcu_dereference(inet6_protos[proto]);
if (!ops || !ops->gro_receive)
NAPI_GRO_CB(skb)->flush |= flush;
+ csum = skb->csum;
+ skb_postpull_rcsum(skb, iph, skb_network_header_len(skb));
+
pp = ops->gro_receive(head, skb);
+ skb->csum = csum;
+
out_unlock:
rcu_read_unlock();
ext_hdrs[SADB_X_EXT_NAT_T_DPORT-1];
natt->encap_dport = n_port->sadb_x_nat_t_port_port;
}
+ memset(&natt->encap_oa, 0, sizeof(natt->encap_oa));
}
err = xfrm_init_state(x);
if (use_short_slot != bss_conf->use_short_slot) {
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
if (net_ratelimit()) {
- printk(KERN_DEBUG "%s: switched to %s slot"
- " (BSSID=%s)\n",
+ printk(KERN_DEBUG "%s: switched to %s slot time"
+ " (BSSID=%pM)\n",
sdata->dev->name,
use_short_slot ? "short" : "long",
ifsta->bssid);
* @tx_packets: number of RX/TX MSDUs
* @tx_bytes: number of bytes transmitted to this STA
* @tx_fragments: number of transmitted MPDUs
- * @last_txrate: description of the last used transmit rate
* @tid_seq: per-TID sequence numbers for sending to this STA
* @ampdu_mlme: A-MPDU state machine state
* @timer_to_tid: identity mapping to ID timers
if (is_multicast_ether_addr(hdr->addr3))
memcpy(hdr->addr1, hdr->addr3, ETH_ALEN);
else
- if (mesh_nexthop_lookup(skb, osdata))
- return 0;
+ if (mesh_nexthop_lookup(skb, osdata)) {
+ dev_put(odev);
+ return 0;
+ }
if (memcmp(odev->dev_addr, hdr->addr4, ETH_ALEN) != 0)
IEEE80211_IFSTA_MESH_CTR_INC(&osdata->u.mesh,
fwded_frames);
if (!parse_nat_setup) {
#ifdef CONFIG_MODULES
rcu_read_unlock();
+ spin_unlock_bh(&nf_conntrack_lock);
nfnl_unlock();
if (request_module("nf-nat-ipv4") < 0) {
nfnl_lock();
+ spin_lock_bh(&nf_conntrack_lock);
rcu_read_lock();
return -EOPNOTSUPP;
}
nfnl_lock();
+ spin_lock_bh(&nf_conntrack_lock);
rcu_read_lock();
if (nfnetlink_parse_nat_setup_hook)
return -EAGAIN;
*/
sctp_bh_lock_sock(sk);
+ if (sk != rcvr->sk) {
+ /* Our cached sk is different from the rcvr->sk. This is
+ * because migrate()/accept() may have moved the association
+ * to a new socket and released all the sockets. So now we
+ * are holding a lock on the old socket while the user may
+ * be doing something with the new socket. Switch our veiw
+ * of the current sk.
+ */
+ sctp_bh_unlock_sock(sk);
+ sk = rcvr->sk;
+ sctp_bh_lock_sock(sk);
+ }
+
if (sock_owned_by_user(sk)) {
SCTP_INC_STATS_BH(SCTP_MIB_IN_PKT_BACKLOG);
sctp_add_backlog(sk, skb);
switch (chunk->chunk_hdr->type) {
case SCTP_CID_DATA:
retval = sctp_packet_append_data(packet, chunk);
+ if (SCTP_XMIT_OK != retval)
+ goto finish;
/* Disallow SACK bundling after DATA. */
packet->has_sack = 1;
/* Disallow AUTH bundling after DATA */
packet->has_auth = 1;
/* Let it be knows that packet has DATA in it */
packet->has_data = 1;
- if (SCTP_XMIT_OK != retval)
- goto finish;
+ /* timestamp the chunk for rtx purposes */
+ chunk->sent_at = jiffies;
break;
case SCTP_CID_COOKIE_ECHO:
packet->has_cookie_echo = 1;
} else
chunk->resent = 1;
- chunk->sent_at = jiffies;
has_data = 1;
}
}
/* Finally, transmit new packets. */
- start_timer = 0;
while ((chunk = sctp_outq_dequeue_data(q)) != NULL) {
/* RFC 2960 6.5 Every DATA chunk MUST carry a valid
* stream identifier.
list_add_tail(&chunk->transmitted_list,
&transport->transmitted);
- sctp_transport_reset_timers(transport, start_timer-1);
+ sctp_transport_reset_timers(transport, 0);
q->empty = 0;
return 0;
}
+/**
+ * freq_in_rule_band - tells us if a frequency is in a frequency band
+ * @freq_range: frequency rule we want to query
+ * @freq_khz: frequency we are inquiring about
+ *
+ * This lets us know if a specific frequency rule is or is not relevant to
+ * a specific frequency's band. Bands are device specific and artificial
+ * definitions (the "2.4 GHz band" and the "5 GHz band"), however it is
+ * safe for now to assume that a frequency rule should not be part of a
+ * frequency's band if the start freq or end freq are off by more than 2 GHz.
+ * This resolution can be lowered and should be considered as we add
+ * regulatory rule support for other "bands".
+ **/
+static bool freq_in_rule_band(const struct ieee80211_freq_range *freq_range,
+ u32 freq_khz)
+{
+#define ONE_GHZ_IN_KHZ 1000000
+ if (abs(freq_khz - freq_range->start_freq_khz) <= (2 * ONE_GHZ_IN_KHZ))
+ return true;
+ if (abs(freq_khz - freq_range->end_freq_khz) <= (2 * ONE_GHZ_IN_KHZ))
+ return true;
+ return false;
+#undef ONE_GHZ_IN_KHZ
+}
+
/* Converts a country IE to a regulatory domain. A regulatory domain
* structure has a lot of information which the IE doesn't yet have,
* so for the other values we use upper max values as we will intersect
/* This time around we fill in the rd */
while (country_ie_len >= 3) {
+ int end_channel = 0;
struct ieee80211_country_ie_triplet *triplet =
(struct ieee80211_country_ie_triplet *) country_ie;
struct ieee80211_reg_rule *reg_rule = NULL;
reg_rule->flags = flags;
+ /* 2 GHz */
+ if (triplet->chans.first_channel <= 14)
+ end_channel = triplet->chans.first_channel +
+ triplet->chans.num_channels;
+ else
+ /*
+ * 5 GHz -- For example in country IEs if the first
+ * channel given is 36 and the number of channels is 4
+ * then the individual channel numbers defined for the
+ * 5 GHz PHY by these parameters are: 36, 40, 44, and 48
+ * and not 36, 37, 38, 39.
+ *
+ * See: http://tinyurl.com/11d-clarification
+ */
+ end_channel = triplet->chans.first_channel +
+ (4 * (triplet->chans.num_channels - 1));
+
/* The +10 is since the regulatory domain expects
* the actual band edge, not the center of freq for
* its start and end freqs, assuming 20 MHz bandwidth on
triplet->chans.first_channel) - 10);
freq_range->end_freq_khz =
MHZ_TO_KHZ(ieee80211_channel_to_frequency(
- triplet->chans.first_channel +
- triplet->chans.num_channels) + 10);
+ end_channel) + 10);
/* Large arbitrary values, we intersect later */
/* Increment this if we ever support >= 40 MHz channels
* this value to the maximum allowed bandwidth.
* @reg_rule: the regulatory rule which we have for this frequency
*
- * Use this function to get the regulatory rule for a specific frequency.
+ * Use this function to get the regulatory rule for a specific frequency on
+ * a given wireless device. If the device has a specific regulatory domain
+ * it wants to follow we respect that unless a country IE has been received
+ * and processed already.
+ *
+ * Returns 0 if it was able to find a valid regulatory rule which does
+ * apply to the given center_freq otherwise it returns non-zero. It will
+ * also return -ERANGE if we determine the given center_freq does not even have
+ * a regulatory rule for a frequency range in the center_freq's band. See
+ * freq_in_rule_band() for our current definition of a band -- this is purely
+ * subjective and right now its 802.11 specific.
*/
static int freq_reg_info(u32 center_freq, u32 *bandwidth,
const struct ieee80211_reg_rule **reg_rule)
{
int i;
+ bool band_rule_found = false;
u32 max_bandwidth = 0;
if (!cfg80211_regdomain)
rr = &cfg80211_regdomain->reg_rules[i];
fr = &rr->freq_range;
pr = &rr->power_rule;
+
+ /* We only need to know if one frequency rule was
+ * was in center_freq's band, that's enough, so lets
+ * not overwrite it once found */
+ if (!band_rule_found)
+ band_rule_found = freq_in_rule_band(fr, center_freq);
+
max_bandwidth = freq_max_bandwidth(fr, center_freq);
+
if (max_bandwidth && *bandwidth <= max_bandwidth) {
*reg_rule = rr;
*bandwidth = max_bandwidth;
}
}
+ if (!band_rule_found)
+ return -ERANGE;
+
return !max_bandwidth;
}
-static void handle_channel(struct ieee80211_channel *chan)
+static void handle_channel(struct wiphy *wiphy, enum ieee80211_band band,
+ unsigned int chan_idx)
{
int r;
- u32 flags = chan->orig_flags;
+ u32 flags;
u32 max_bandwidth = 0;
const struct ieee80211_reg_rule *reg_rule = NULL;
const struct ieee80211_power_rule *power_rule = NULL;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_channel *chan;
+
+ sband = wiphy->bands[band];
+ BUG_ON(chan_idx >= sband->n_channels);
+ chan = &sband->channels[chan_idx];
+
+ flags = chan->orig_flags;
r = freq_reg_info(MHZ_TO_KHZ(chan->center_freq),
&max_bandwidth, ®_rule);
if (r) {
- flags |= IEEE80211_CHAN_DISABLED;
- chan->flags = flags;
+ /* This means no regulatory rule was found in the country IE
+ * with a frequency range on the center_freq's band, since
+ * IEEE-802.11 allows for a country IE to have a subset of the
+ * regulatory information provided in a country we ignore
+ * disabling the channel unless at least one reg rule was
+ * found on the center_freq's band. For details see this
+ * clarification:
+ *
+ * http://tinyurl.com/11d-clarification
+ */
+ if (r == -ERANGE &&
+ last_request->initiator == REGDOM_SET_BY_COUNTRY_IE) {
+#ifdef CONFIG_CFG80211_REG_DEBUG
+ printk(KERN_DEBUG "cfg80211: Leaving channel %d MHz "
+ "intact on %s - no rule found in band on "
+ "Country IE\n",
+ chan->center_freq, wiphy_name(wiphy));
+#endif
+ } else {
+ /* In this case we know the country IE has at least one reg rule
+ * for the band so we respect its band definitions */
+#ifdef CONFIG_CFG80211_REG_DEBUG
+ if (last_request->initiator == REGDOM_SET_BY_COUNTRY_IE)
+ printk(KERN_DEBUG "cfg80211: Disabling "
+ "channel %d MHz on %s due to "
+ "Country IE\n",
+ chan->center_freq, wiphy_name(wiphy));
+#endif
+ flags |= IEEE80211_CHAN_DISABLED;
+ chan->flags = flags;
+ }
return;
}
chan->max_power = (int) MBM_TO_DBM(power_rule->max_eirp);
}
-static void handle_band(struct ieee80211_supported_band *sband)
+static void handle_band(struct wiphy *wiphy, enum ieee80211_band band)
{
- int i;
+ unsigned int i;
+ struct ieee80211_supported_band *sband;
+
+ BUG_ON(!wiphy->bands[band]);
+ sband = wiphy->bands[band];
for (i = 0; i < sband->n_channels; i++)
- handle_channel(&sband->channels[i]);
+ handle_channel(wiphy, band, i);
}
static bool ignore_reg_update(struct wiphy *wiphy, enum reg_set_by setby)
enum ieee80211_band band;
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
if (wiphy->bands[band])
- handle_band(wiphy->bands[band]);
+ handle_band(wiphy, band);
if (wiphy->reg_notifier)
wiphy->reg_notifier(wiphy, setby);
}
}
#endif
-/* For the xfrm_usersa_info cases we have to work around some 32-bit vs.
- * 64-bit compatability issues. On 32-bit the structure is 220 bytes, but
- * for 64-bit it gets padded out to 224 bytes. Those bytes are just
- * padding and don't have any content we care about. Therefore as long
- * as we have enough bytes for the content we can make both cases work.
- */
-
#define XMSGSIZE(type) sizeof(struct type)
static const int xfrm_msg_min[XFRM_NR_MSGTYPES] = {
- [XFRM_MSG_NEWSA - XFRM_MSG_BASE] = 220, /* see above */
+ [XFRM_MSG_NEWSA - XFRM_MSG_BASE] = XMSGSIZE(xfrm_usersa_info),
[XFRM_MSG_DELSA - XFRM_MSG_BASE] = XMSGSIZE(xfrm_usersa_id),
[XFRM_MSG_GETSA - XFRM_MSG_BASE] = XMSGSIZE(xfrm_usersa_id),
[XFRM_MSG_NEWPOLICY - XFRM_MSG_BASE] = XMSGSIZE(xfrm_userpolicy_info),
[XFRM_MSG_ACQUIRE - XFRM_MSG_BASE] = XMSGSIZE(xfrm_user_acquire),
[XFRM_MSG_EXPIRE - XFRM_MSG_BASE] = XMSGSIZE(xfrm_user_expire),
[XFRM_MSG_UPDPOLICY - XFRM_MSG_BASE] = XMSGSIZE(xfrm_userpolicy_info),
- [XFRM_MSG_UPDSA - XFRM_MSG_BASE] = 220, /* see above */
+ [XFRM_MSG_UPDSA - XFRM_MSG_BASE] = XMSGSIZE(xfrm_usersa_info),
[XFRM_MSG_POLEXPIRE - XFRM_MSG_BASE] = XMSGSIZE(xfrm_user_polexpire),
[XFRM_MSG_FLUSHSA - XFRM_MSG_BASE] = XMSGSIZE(xfrm_usersa_flush),
[XFRM_MSG_FLUSHPOLICY - XFRM_MSG_BASE] = 0,
projects / linux-2.6-omap-h63xx.git / commitdiff