M: mickflemm@gmail.com
P: Luis R. Rodriguez
M: mcgrof@gmail.com
+P: Bob Copeland
+M: me@bobcopeland.com
L: linux-wireless@vger.kernel.org
L: ath5k-devel@lists.ath5k.org
S: Maintained
sc->opmode != NL80211_IFTYPE_MESH_POINT &&
test_bit(ATH_STAT_PROMISC, sc->status))
rfilt |= AR5K_RX_FILTER_PROM;
- if (sc->opmode == NL80211_IFTYPE_STATION ||
- sc->opmode == NL80211_IFTYPE_ADHOC) {
+ if (sc->opmode == NL80211_IFTYPE_ADHOC)
rfilt |= AR5K_RX_FILTER_BEACON;
- }
/* Set filters */
ath5k_hw_set_rx_filter(ah,rfilt);
{ ATH5K_DEBUG_BEACON, "beacon", "beacon handling" },
{ ATH5K_DEBUG_CALIBRATE, "calib", "periodic calibration" },
{ ATH5K_DEBUG_TXPOWER, "txpower", "transmit power setting" },
- { ATH5K_DEBUG_LED, "led", "LED mamagement" },
+ { ATH5K_DEBUG_LED, "led", "LED management" },
{ ATH5K_DEBUG_DUMP_RX, "dumprx", "print received skb content" },
{ ATH5K_DEBUG_DUMP_TX, "dumptx", "print transmit skb content" },
{ ATH5K_DEBUG_DUMPBANDS, "dumpbands", "dump bands" },
{ 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 } },
{ AR5K_PHY(642),
{ 0xd03e6788, 0xd03e6788, 0xd03e6788, 0xd03e6788, 0xd03e6788 } },
+ { 0xa228,
+ { 0x000001b5, 0x000001b5, 0x000001b5, 0x000001b5, 0x000001b5 } },
{ 0xa23c,
{ 0x13c889af, 0x13c889af, 0x13c889af, 0x13c889af, 0x13c889af } },
};
mdelay(1);
/*
- * Write some more initial register settings
+ * Write some more initial register settings for revised chips
*/
- if (ah->ah_version == AR5K_AR5212) {
+ if (ah->ah_version == AR5K_AR5212 &&
+ ah->ah_phy_revision > 0x41) {
ath5k_hw_reg_write(ah, 0x0002a002, 0x982c);
if (channel->hw_value == CHANNEL_G)
else
ath5k_hw_reg_write(ah, 0x00000000, 0x994c);
- /* Some bits are disabled here, we know nothing about
- * register 0xa228 yet, most of the times this ends up
- * with a value 0x9b5 -haven't seen any dump with
- * a different value- */
- /* Got this from decompiling binary HAL */
- data = ath5k_hw_reg_read(ah, 0xa228);
- data &= 0xfffffdff;
- ath5k_hw_reg_write(ah, data, 0xa228);
-
- data = ath5k_hw_reg_read(ah, 0xa228);
- data &= 0xfffe03ff;
- ath5k_hw_reg_write(ah, data, 0xa228);
- data = 0;
+ /* Got this from legacy-hal */
+ AR5K_REG_DISABLE_BITS(ah, 0xa228, 0x200);
+
+ AR5K_REG_MASKED_BITS(ah, 0xa228, 0x800, 0xfffe03ff);
/* Just write 0x9b5 ? */
/* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */
iwl4965_error_recovery(priv);
iwl_power_update_mode(priv, 1);
- ieee80211_notify_mac(priv->hw, IEEE80211_NOTIFY_RE_ASSOC);
if (test_and_clear_bit(STATUS_MODE_PENDING, &priv->status))
iwl4965_set_mode(priv, priv->iw_mode);
mutex_lock(&priv->mutex);
iwl_alive_start(priv);
mutex_unlock(&priv->mutex);
+ ieee80211_notify_mac(priv->hw, IEEE80211_NOTIFY_RE_ASSOC);
}
static void iwl4965_bg_rf_kill(struct work_struct *work)
if (ret == 0) {
*curlevel = le16_to_cpu(cmd.curlevel);
if (minlevel)
- *minlevel = le16_to_cpu(cmd.minlevel);
+ *minlevel = cmd.minlevel;
if (maxlevel)
- *maxlevel = le16_to_cpu(cmd.maxlevel);
+ *maxlevel = cmd.maxlevel;
}
lbs_deb_leave(LBS_DEB_CMD);
switch (elem->id) {
case MFIE_TYPE_SSID:
- bss->ssid_len = elem->len;
- memcpy(bss->ssid, elem->data, elem->len);
+ bss->ssid_len = min_t(int, 32, elem->len);
+ memcpy(bss->ssid, elem->data, bss->ssid_len);
lbs_deb_scan("got SSID IE: '%s', len %u\n",
escape_essid(bss->ssid, bss->ssid_len),
bss->ssid_len);
menuconfig RT2X00
- bool "Ralink driver support"
+ tristate "Ralink driver support"
depends on MAC80211 && WLAN_80211 && EXPERIMENTAL
---help---
This will enable the experimental support for the Ralink drivers,