David Brownell [Fri, 7 Nov 2008 05:15:30 +0000 (21:15 -0800)]
hsmmc gpio updates
Rework card detect GPIO handling in the twl4030 MMC glue: drive
it *only* from the hsmmc_info passed; remove most of remaining
"we know we're always a twl4030 GPIO" logic.
Add write-protect switch detection support to that glue. Stub
in a not-present WP GPIO into most boards. (Beagle's is real.)
Teach the hsmmc driver how to use the card detect and writeprotect
methods, and move some data structure init earlier so that when IRQs
come in, more of the data used by their handlers is initialized.
Verified on Beagle (WP, card detect events) and Overo (boots, both
card and wlan are seen). Beagle behaves fully, and is the model
to follow for the common case where the TWL4030 gpio-0 card detect
magic is used.
Most hsmmc boards need to list what GPIOs they use with MMC...
Note that supporting card detect and writeprotect GPIOs on a
second MMC slot, or using the MMC3 controller, requires some
interface updates that aren't part of this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 6 Nov 2008 17:06:21 +0000 (09:06 -0800)]
HSMMC: Build fixes for earlier patches
Build fixes for "HSMMC: Improve the interface for hsmmc_init()".
The header file needs to work without MMC support enabled, and
some board files needed to include it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 6 Nov 2008 11:08:44 +0000 (04:08 -0700)]
OMAP3 powerdomains: remove RET from SGX power states list
On Wed, 5 Nov 2008, Tony Lindgren wrote:
> * Paul Walmsley <paul@pwsan.com> [081105 11:39]:
> >
> > The SGX device on OMAP3 does not support retention, so remove RET from the
> > list of possible SGX power states. Problem debugged by Richard Woodruff
> > <r-woodruff2@ti.com>.
>
> Pushing.
Just FYI, that patch prevents the kernel from booting due to a bug in
pm34xx.c; patch below.
Even with the follwoing patch, the initial power state setup code in
pm34xx.c will bail out early since it still tries to set the SGX next
power state to retention, which it does not support.
- Paul
OMAP3 PM: use list_for_each_entry_safe() when deleting list entries
From: Paul Walmsley <paul@pwsan.com>
The error path in clkdms_setup() needs to use list_for_each_entry_safe()
when deleting entries from the list, or the kernel will crash.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Jouni Högander <jouni.hogander@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Wed, 5 Nov 2008 19:39:27 +0000 (12:39 -0700)]
OMAP3 powerdomains: remove RET from SGX power states list
The SGX device on OMAP3 does not support retention, so remove RET from the
list of possible SGX power states. Problem debugged by Richard Woodruff
<r-woodruff2@ti.com>.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Lauri Leukkunen [Sat, 1 Nov 2008 11:07:04 +0000 (13:07 +0200)]
OMAP: Use omap_rev() instead of system_rev
system_rev is meant for board revision, this patch changes
all relevant instances to use the new omap_rev() function
liberating system_rev to be used with ATAG_REVISION as it
has been designed.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Russell King [Tue, 4 Nov 2008 10:52:28 +0000 (10:52 +0000)]
mm: fix page table initialization
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Acked-by: Tony Lindgren <tony@atomide.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Tested-by: Mike Rapoport <mike@compulab.co.il> Tested-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Russell King - ARM Linux <linux@arm.linux.org.uk> [081103 07:09]:
> Solving ARMv7 seems to be fairly simple, at the expense of making
> build_mem_types_table() slightly more complex. If that was the only
> problem, then I wouldn't be mentioning the idea of dropping the
> patchset.
Well, this is the fix for ARMv7 (and a few others). In making these
changes, I went back to DDI0100I (ARMv6 ARM), DDI0406A (ARMv7 ARM)
and the Marvell Xscale3 documentation.
...
Note that this version has a bug with xscale handling, but works
for omap. This patch will get reverted once the final patch is
available.
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-gd: re-get capacity on revalidate
tx4938ide: Avoid underflow on calculation of a wait cycle
tx4938ide: Do not call devm_ioremap for whole 128KB
tx4938ide: Check minimum cycle time and SHWT range (v2)
ide: Switch to a common address
ide-cd: fix DMA alignment regression
Atsushi Nemoto [Sun, 2 Nov 2008 20:40:09 +0000 (21:40 +0100)]
tx4938ide: Check minimum cycle time and SHWT range (v2)
SHWT value is used as address valid to -CSx assertion and -CSx to -DIOx
assertion setup time, and contrarywise, -DIOx to -CSx release and -CSx
release to address invalid hold time, so it actualy applies 4 times and
so constitutes -DIOx recovery time. Check requirement of the recovery
time and cycle time. Also check SHWT maximum value.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: ralf@linux-mips.org Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Sun, 2 Nov 2008 20:40:07 +0000 (21:40 +0100)]
ide-cd: fix DMA alignment regression
e5318b531b008c79d2a0c0df06a7b8628da38e2f ("ide: use the dma safe check for
REQ_TYPE_ATA_PC") introduced a regression which caused some ATAPI drives to
turn off DMA for REQ_TYPE_BLOCK_PC commands while burning and thus degrading
performance and ultimately causing an excessive amount of underruns.
The issue is documented also in:
http://bugzilla.kernel.org/show_bug.cgi?id=11742.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Tested-by: Valerio Passini <valerio.passini@unicam.it>
[bart: fixup patch description per comments from Sergei Shtylyov] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
There is a problem discovered in recent versions of ATI Mach64 driver
in X.org on sparc64 architecture. In short, the driver fails to mmap
MMIO aperture (PCI resource #2).
I've found that kernel's __pci_mmap_make_offset() returns EINVAL. It
checks whether user attempts to mmap more than the resource length,
which is 0x1000 bytes in our case. But PAGE_SIZE on SPARC64 is 0x2000
and this is what actually is being mmaped. So __pci_mmap_make_offset()
failed for this PCI resource.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Beregalov reports oops in __bzero() called from
copy_from_user_fixup() called from iov_iter_copy_from_user_atomic(),
when running dbench on tmpfs on sparc64: its __copy_from_user_inatomic
and __copy_to_user_inatomic should be avoiding, not calling, the fixups.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04a4bb55bcf35b63d40fd2725e58599ff8310dd7 ("net: add
skb_recycle_check() to enable netdriver skb recycling") added a
method for network drivers to recycle skbuffs, but while use of
this mechanism was documented in the commit message, it should
really have been added as a docbook comment as well -- this
patch does that.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Sat, 1 Nov 2008 18:20:39 +0000 (18:20 +0000)]
section fixes for cirrusfb
cirrusfb_zorro_unmap() may be called both from __devexit and (on
cleanup path) from __devinit. So it needs to be a normal function,
same as for cirrusfb_pci_unmap()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 1 Nov 2008 18:19:49 +0000 (18:19 +0000)]
oss: fix O_NONBLOCK in dmasound_core
We broke O_NONBLOCK handling in OSS dmasound_core in 2.3.11-pre3 - the
original code copied f_flags to open_mode and then checked for
O_NONBLOCK in there, but that got changed to copying f_mode and
O_NONBLOCK has not reached that field in any kernel version.
Since we do not care for any other bits, the fix is obvious...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 1 Nov 2008 17:36:30 +0000 (10:36 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix AMDC1E and XTOPOLOGY conflict in cpufeature
x86: build fix
by people adding the <linux/delay.h> include in two slightly different
places. Andrew's quilt scripts happily ignore the fuzz, and will
re-apply the patch even though they had conflicts.
Linus Torvalds [Sat, 1 Nov 2008 17:17:22 +0000 (10:17 -0700)]
x86: Clean up late e820 resource allocation
This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.
This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions. It also
makes for a simpler and more accurate resource tree.
Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.
With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:
and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:
e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]
with this patch, the resource tree instead becomes
ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: Jonathan Corbet <corbet@lwn.net> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 1 Nov 2008 16:53:58 +0000 (09:53 -0700)]
reserve_region_with_split: Fix GFP_KERNEL usage under spinlock
This one apparently doesn't generate any warnings, because the function
is only used during system bootup, when the warnings are disabled. But
it's still very wrong.
The __reserve_region_with_split() function is called with the
resource_lock held for writing, so it must only ever do GFP_ATOMIC
allocations.
Al Viro [Fri, 31 Oct 2008 23:28:30 +0000 (23:28 +0000)]
saner FASYNC handling on file close
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serge Hallyn [Thu, 30 Oct 2008 16:52:23 +0000 (11:52 -0500)]
file caps: always start with clear bprm->caps_*
While Linux doesn't honor setuid on scripts. However, it mistakenly
behaves differently for file capabilities.
This patch fixes that behavior by making sure that get_file_caps()
begins with empty bprm->caps_*. That way when a script is loaded,
its bprm->caps_* may be filled when binfmt_misc calls prepare_binprm(),
but they will be cleared again when binfmt_elf calls prepare_binprm()
next to read the interpreter's file capabilities.
Signed-off-by: Serge Hallyn <serue@us.ibm.com> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2008 22:44:08 +0000 (15:44 -0700)]
Merge branch 'for-2.6.28' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
NLM: Set address family before calling nlm_host_rebooted()
nfsd: fix failure to set eof in readdir in some situations
Eric Paris [Fri, 31 Oct 2008 21:40:00 +0000 (17:40 -0400)]
SELinux: properly handle empty tty_files list
SELinux has wrongly (since 2004) had an incorrect test for an empty
tty->tty_files list. With an empty list selinux would be pointing to part
of the tty struct itself and would then proceed to dereference that value
and again dereference that result. An F10 change to plymouth on a ppc64
system is actually currently triggering this bug. This patch uses
list_empty() to handle empty lists rather than looking at a meaningless
location.
[note, this fixes the oops reported in
https://bugzilla.redhat.com/show_bug.cgi?id=469079]
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Jesper Nilsson [Wed, 22 Oct 2008 21:57:53 +0000 (23:57 +0200)]
[CRIS] Remove links from CRIS build
Remove the links to architecture and machine dependent directories
(boot, lib, drivers, arch, mach)
The links were created and used mostly from the arch/cris/Makefile,
so why not dispense with them altogether?
Changed $(ARCH) to "cris" in Makefile, it is easier to read this way.
The CRISv32 head.S common files for the kernel and compressed images
needed to be modified to use ifdefs instead of using the now removed
mach link. Since there are only two versions, this is not a huge loss
in readability.
The link to vmlinux.lds.S is also replaced with a merged version
which uses ifdefs to select the correct layout.
System.map before and after are identical.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Linus Torvalds [Fri, 31 Oct 2008 15:14:15 +0000 (08:14 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (21 commits)
sh: fix sh2a cache entry_mask
sh: Enable NFS root in Migo-R defconfig.
sh: FTRACE renamed to FUNCTION_TRACER.
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Define SCSPTR1 for SH 7751R
sh: Add sci_rxd_in of SH4-202
Add support usb setting on sh 7366
sh: Change register name SCSPTR to SCSPTR2
sh: use the new byteorder headers.
sh: SHmedia ISA tuning fixups.
sh: Kill off long-dead HD64465 cchip support.
sh: Revert "SH 7366 needs SCIF_ONLY"
sh: Simplify and lock down the ISA tuning.
sh: sh7785lcr: Select uImage as default image target.
sh: Add on-chip RTC support for SH7722.
SH 7366 needs SCIF_ONLY
gdrom: Fix compile error
sh: Provide a sample defconfig for the UL2 (SH7366) board.
sh: Fix FPU tuning on toolchains with mismatched multilib targets.
sh: oprofile: Fix up the SH7750 performance counter name.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add missing null terminating entry to bq4802_match[].
sparc: use the new byteorder headers
rtc-m48t59: shift zero year to 1968 on sparc (rev 2)
dbri: check dma_alloc_coherent errors
sparc64: remove byteshifting from out* helpers
Linus Torvalds [Fri, 31 Oct 2008 14:52:12 +0000 (07:52 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
delay capable() check in ext4_has_free_blocks()
merge ext4_claim_free_blocks & ext4_has_free_blocks
jbd2: Call the commit callback before the transaction could get dropped
ext4: fix a bug accessing freed memory in ext4_abort
ext3: fix a bug accessing freed memory in ext3_abort
Linus Torvalds [Fri, 31 Oct 2008 14:47:57 +0000 (07:47 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: add whitelist for devices with known good pata-sata bridges
sata_via: fix support for 5287
libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
ATA: remove excess kernel-doc notation
Paul Mackerras [Fri, 31 Oct 2008 10:34:09 +0000 (21:34 +1100)]
powerpc: Fix compile errors with CONFIG_BUG=n
This makes sure we don't try to call find_bug or is_warning_bug when
CONFIG_BUG=n and CONFIG_XMON=y. Otherwise we get these errors:
arch/powerpc/xmon/xmon.c: In function ‘print_bug_trap’:
arch/powerpc/xmon/xmon.c:1364: error: implicit declaration of function ‘find_bug’
arch/powerpc/xmon/xmon.c:1364: warning: assignment makes pointer from integer without a cast
arch/powerpc/xmon/xmon.c:1367: error: implicit declaration of function ‘is_warning_bug’
arch/powerpc/xmon/xmon.c:1374: error: dereferencing pointer to incomplete type
make[2]: *** [arch/powerpc/xmon/xmon.o] Error 1
make[1]: *** [arch/powerpc/xmon] Error 2
make: *** [sub-make] Error 2
Jon Smirl [Thu, 30 Oct 2008 16:51:32 +0000 (16:51 +0000)]
powerpc: Fix format string warning in arch/powerpc/boot/main.c
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 30 Oct 2008 16:37:05 +0000 (16:37 +0000)]
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450dcbfeb45ffc9d39b1747aee82b49a51 ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Ingo Molnar [Fri, 31 Oct 2008 08:31:38 +0000 (09:31 +0100)]
x86: build fix
Impact: build fix on certain UP configs
fix:
arch/x86/kernel/cpu/common.c: In function 'cpu_init':
arch/x86/kernel/cpu/common.c:1141: error: 'boot_cpu_id' undeclared (first use in this function)
arch/x86/kernel/cpu/common.c:1141: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/common.c:1141: error: for each function it appears in.)
Pull in asm/smp.h on UP, so that we get the definition of
boot_cpu_id.
Ilpo Järvinen [Fri, 31 Oct 2008 07:40:19 +0000 (00:40 -0700)]
bpa10x: free sk_buff with kfree_skb
Inspired by Sergio Luis' similar patches, I finally found
a case which is trivial enough that spatch won't choke
on it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Matt Fleming [Wed, 29 Oct 2008 07:16:02 +0000 (07:16 +0000)]
Define SCSPTR1 for SH 7751R
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I noticed that, under certain conditions, ESRCH can be leaked from the
xfrm layer to user space through sys_connect. In particular, this seems
to happen reliably when the kernel fails to resolve a template either
because the AF_KEY receive buffer being used by racoon is full or
because the SA entry we are trying to use is in XFRM_STATE_EXPIRED
state.
However, since this could be a transient issue it could be argued that
EAGAIN would be more appropriate. Besides this error code is not even
documented in the man page for sys_connect (as of man-pages 3.07).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Fri, 31 Oct 2008 07:01:22 +0000 (16:01 +0900)]
sh: use the new byteorder headers.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
David S. Miller [Fri, 31 Oct 2008 07:00:33 +0000 (00:00 -0700)]
net: Really remove all of LOOPBACK_TSO code.
As noticed by Saikiran Madugula, commit 7447ef63cf2dfdc444f4c72ae13f604350b2e25f
("loopback: Remove rest of LOOPBACK_TSO code.") got rid of
emulate_large_send_offload() but didn't get rid of the call
site as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Fri, 31 Oct 2008 06:55:44 +0000 (23:55 -0700)]
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
register_pernet_gen_device() can't be used is nf_conntrack_pptp module is
also used (compiled in or loaded).
Right now, proto_gre_net_exit() is called before nf_conntrack_pptp_net_exit().
The former shutdowns and frees GRE piece of netns, however the latter
absolutely needs it to flush keymap. Oops is inevitable.
Switch to shiny new register_pernet_gen_subsys() to get correct ordering in
netns ops list.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netns ops which are registered with register_pernet_gen_device() are
shutdown strictly before those which are registered with
register_pernet_subsys(). Sometimes this leads to opposite (read: buggy)
shutdown ordering between two modules.
Add register_pernet_gen_subsys()/unregister_pernet_gen_subsys() for modules
which aren't elite enough for entry in struct net, and which can't use
register_pernet_gen_device(). PPTP conntracking module is such one.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 31 Oct 2008 06:54:35 +0000 (23:54 -0700)]
net: delete excess kernel-doc notation
Remove excess kernel-doc function parameters from networking header
& driver files:
Warning(include/net/sock.h:946): Excess function parameter or struct member 'sk' description in 'sk_filter_release'
Warning(include/linux/netdevice.h:1545): Excess function parameter or struct member 'cpu' description in 'netif_tx_lock'
Warning(drivers/net/wan/z85230.c:712): Excess function parameter or struct member 'regs' description in 'z8530_interrupt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jens Axboe [Wed, 27 Aug 2008 13:23:18 +0000 (15:23 +0200)]
libata: add whitelist for devices with known good pata-sata bridges
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Tejun Heo [Tue, 21 Oct 2008 15:46:36 +0000 (00:46 +0900)]
sata_via: fix support for 5287
5287 used to be treated as vt6420 but it didn't work. It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports. This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata. Another controller
which falls into this category is ata_piix w/ SIDPR access.
libata now has facility to deal with this class of controllers named
slave_link. A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.
This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.
This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.
projects / linux-2.6-omap-h63xx.git / log