This option enables support for the LEDs on Sharp Locomo.
Zaurus models SL-5500 and SL-5600.
+config LEDS_MIKROTIK_RB532
+ tristate "LED Support for Mikrotik Routerboard 532"
+ depends on LEDS_CLASS && MIKROTIK_RB532
+ help
+ This option enables support for the so called "User LED" of
+ Mikrotik's Routerboard 532.
+
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
tristate "LED Support for the HP Jornada 6xx"
depends on LEDS_CLASS && SH_HP6XX
help
- This option enables led support for the handheld
+ This option enables LED support for the handheld
HP Jornada 620/660/680/690.
config LEDS_PCA9532
depends on LEDS_CLASS && I2C && INPUT && EXPERIMENTAL
help
This option enables support for NXP pca9532
- led controller. It is generally only usefull
+ LED controller. It is generally only useful
as a platform driver
config LEDS_GPIO
help
This option enables support for the LEDs connected to GPIO
outputs. To be useful the particular board must have LEDs
- and they must be connected to the GPIO lines.
+ and they must be connected to the GPIO lines. The LEDs must be
+ defined as platform devices and/or OpenFirmware platform devices.
+ The code to use these bindings can be selected below.
+
+config LEDS_GPIO_PLATFORM
+ bool "Platform device bindings for GPIO LEDs"
+ depends on LEDS_GPIO
+ default y
+ help
+ Let the leds-gpio driver drive LEDs which have been defined as
+ platform devices. If you don't know what this means, say yes.
+
+config LEDS_GPIO_OF
+ bool "OpenFirmware platform device bindings for GPIO LEDs"
+ depends on LEDS_GPIO && OF_DEVICE
+ default y
+ help
+ Let the leds-gpio driver drive LEDs which have been defined as
+ of_platform devices. For instance, LEDs which are listed in a "dts"
+ file.
+
+config LEDS_LP5521
+ tristate "LED Support for the LP5521 LEDs"
+ depends on LEDS_CLASS && I2C
+ help
+ If you say 'Y' here you get support for the National Semiconductor
+ LP5521 LED driver used in n8x0 boards.
+
+ This driver can be built as a module by choosing 'M'. The module
+ will be called leds-lp5521.
config LEDS_LP5521
tristate "LED Support for the LP5521 LEDs"
will be called leds-lp5521.
config LEDS_CLEVO_MAIL
- tristate "Mail LED on Clevo notebook (EXPERIMENTAL)"
- depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI && EXPERIMENTAL
+ tristate "Mail LED on Clevo notebook"
+ depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI
help
This driver makes the mail LED accessible from userspace
programs through the leds subsystem. This LED have three
Positivo Mobile (Clevo M5x0V)
If your model is not listed here you can try the "nodetect"
- module paramter.
+ module parameter.
To compile this driver as a module, choose M here: the
module will be called leds-clevo-mail.
This option enables support for on-chip LED drivers found
on Dialog Semiconductor DA9030/DA9034 PMICs.
+config LEDS_DAC124S085
+ tristate "LED Support for DAC124S085 SPI DAC"
+ depends on LEDS_CLASS && SPI
+ help
+ This option enables support for DAC124S085 SPI DAC from NatSemi,
+ which can be used to control up to four LEDs.
+
+config LEDS_PWM
+ tristate "PWM driven LED Support"
+ depends on LEDS_CLASS && HAVE_PWM
+ help
+ This option enables support for pwm driven LEDs
+
+config LEDS_BD2802
+ tristate "LED driver for BD2802 RGB LED"
+ depends on LEDS_CLASS && I2C
+ help
+ This option enables support for BD2802GU RGB LED driver chips
+ accessed via the I2C bus.
+
comment "LED Triggers"
config LEDS_TRIGGERS
If unsure, say N.
+config LEDS_TRIGGER_GPIO
+ tristate "LED GPIO Trigger"
+ depends on LEDS_TRIGGERS
+ depends on GPIOLIB
+ help
+ This allows LEDs to be controlled by gpio events. It's good
+ when using gpios as switches and triggering the needed LEDs
+ from there. One use case is n810's keypad LEDs that could
+ be triggered by this trigger when user slides up to show
+ keypad.
+
+ If unsure, say N.
+
config LEDS_TRIGGER_DEFAULT_ON
tristate "LED Default ON Trigger"
depends on LEDS_TRIGGERS