ide: Add tx4938ide driver (v2)

[linux-2.6-omap-h63xx.git] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 74a369a6116fc7fbeb7bea0c68c629ec4cfb1102..6d7401772a8f6d7530a89331a16cace5528b4623 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -84,21 +84,40 @@ config BLK_DEV_IDE_SATA
 
          If unsure, say N.
 
-config BLK_DEV_IDEDISK
-       tristate "Include IDE/ATA-2 DISK support"
-       ---help---
-         This will include enhanced support for MFM/RLL/IDE hard disks.  If
-         you have a MFM/RLL/IDE disk, and there is no special reason to use
-         the old hard disk driver instead, say Y.  If you have an SCSI-only
-         system, you can say N here.
+config IDE_GD
+       tristate "generic ATA/ATAPI disk support"
+       default y
+       help
+         Support for ATA/ATAPI disks (including ATAPI floppy drives).
 
-         To compile this driver as a module, choose M here: the
-         module will be called ide-disk.
-         Do not compile this driver as a module if your root file system
-         (the one containing the directory /) is located on the IDE disk.
+         To compile this driver as a module, choose M here.
+         The module will be called ide-gd_mod.
+
+         If unsure, say Y.
+
+config IDE_GD_ATA
+       bool "ATA disk support"
+       depends on IDE_GD
+       default y
+       help
+         This will include support for ATA hard disks.
 
          If unsure, say Y.
 
+config IDE_GD_ATAPI
+       bool "ATAPI floppy support"
+       depends on IDE_GD
+       select IDE_ATAPI
+       help
+         This will include support for ATAPI floppy drives
+         (i.e. Iomega ZIP or MKE LS-120).
+
+         For information about jumper settings and the question
+         of when a ZIP drive uses a partition table, see
+         <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
+
+         If unsure, say N.
+
 config BLK_DEV_IDECS
        tristate "PCMCIA IDE support"
        depends on PCMCIA
@@ -163,29 +182,6 @@ config BLK_DEV_IDETAPE
          To compile this driver as a module, choose M here: the
          module will be called ide-tape.
 
-config BLK_DEV_IDEFLOPPY
-       tristate "Include IDE/ATAPI FLOPPY support"
-       select IDE_ATAPI
-       ---help---
-         If you have an IDE floppy drive which uses the ATAPI protocol,
-         answer Y.  ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
-         drives, similar to the SCSI protocol.
-
-         The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by
-         this driver. For information about jumper settings and the question
-         of when a ZIP drive uses a partition table, see
-         <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
-         (ATAPI PD-CD/CDR drives are not supported by this driver; support
-         for PD-CD/CDR drives is available if you answer Y to
-         "SCSI emulation support", below).
-
-         If you say Y here, the FLOPPY drive will be identified along with
-         other IDE devices, as "hdb" or "hdc", or something similar (check
-         the boot messages with dmesg).
-
-         To compile this driver as a module, choose M here: the
-         module will be called ide-floppy.
-
 config BLK_DEV_IDESCSI
        tristate "SCSI emulation support (DEPRECATED)"
        depends on SCSI
@@ -332,7 +328,7 @@ config IDEPCI_PCIBUS_ORDER
 # TODO: split it on per host driver config options (or module parameters)
 config BLK_DEV_OFFBOARD
        bool "Boot off-board chipsets first support (DEPRECATED)"
-       depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
+       depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
        help
          Normally, IDE controllers built into the motherboard (on-board
          controllers) are assigned to ide0 and ide1 while those on add-in PCI
@@ -482,28 +478,6 @@ config BLK_DEV_CS5535
 
          It is safe to say Y to this question.
 
-config BLK_DEV_HPT34X
-       tristate "HPT34X chipset support"
-       depends on BROKEN
-       select BLK_DEV_IDEDMA_PCI
-       help
-         This driver adds up to 4 more EIDE devices sharing a single
-         interrupt. The HPT343 chipset in its current form is a non-bootable
-         controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX)
-         PCI UDMA controllers. This driver requires dynamic tuning of the
-         chipset during the ide-probe at boot time. It is reported to support
-         DVD II drives, by the manufacturer.
-
-config HPT34X_AUTODMA
-       bool "HPT34X AUTODMA support (EXPERIMENTAL)"
-       depends on BLK_DEV_HPT34X && EXPERIMENTAL
-       help
-         This is a dangerous thing to attempt currently! Please read the
-         comments at the top of <file:drivers/ide/pci/hpt34x.c>.  If you say Y
-         here, then say Y to "Use DMA by default when available" as well.
-
-         If unsure, say N.
-
 config BLK_DEV_HPT366
        tristate "HPT36X/37X chipset support"
        select BLK_DEV_IDEDMA_PCI
@@ -746,6 +720,16 @@ config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
        default "128"
        depends on BLK_DEV_IDE_AU1XXX
 
+config BLK_DEV_IDE_TX4938
+       tristate "TX4938 internal IDE support"
+       depends on SOC_TX4938
+       select IDE_TIMINGS
+
+config BLK_DEV_IDE_TX4939
+       tristate "TX4939 internal IDE support"
+       depends on SOC_TX4939
+       select BLK_DEV_IDEDMA_SFF
+
 config IDE_ARM
        tristate "ARM IDE support"
        depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)