#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
+#include <linux/regulator/machine.h>
#include <linux/i2c/twl4030.h>
#include <mach/hardware.h>
#include <asm/mach/flash.h>
#include <mach/board.h>
+#include <mach/usb-musb.h>
+#include <mach/usb-ehci.h>
#include <mach/common.h>
#include <mach/gpmc.h>
#include <mach/nand.h>
#include <mach/mux.h>
+#include "twl4030-generic-scripts.h"
#include "mmc-twl4030.h"
+
#define GPMC_CS0_BASE 0x60
#define GPMC_CS_SIZE 0x30
.resource = &omap3beagle_nand_resource,
};
+#include "sdram-micron-mt46h32m32lf-6.h"
+
static struct omap_uart_config omap3_beagle_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
+static struct twl4030_usb_data beagle_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
static struct twl4030_hsmmc_info mmc[] = {
{
.mmc = 1,
.setup = beagle_twl_gpio_setup,
};
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data beagle_vmmc1 = {
+ .constraints = {
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data beagle_vsim = {
+ .constraints = {
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
+/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
+static struct regulator_init_data beagle_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+};
+
static struct twl4030_platform_data beagle_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
+ .usb = &beagle_usb_data,
.gpio = &beagle_gpio_data,
+ .power = GENERIC3430_T2SCRIPTS_DATA,
+ .vmmc1 = &beagle_vmmc1,
+ .vsim = &beagle_vsim,
+ .vdac = &beagle_vdac,
};
static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
static void __init omap3_beagle_init_irq(void)
{
- omap2_init_common_hw();
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
omap_init_irq();
omap_gpio_init();
}
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(170, true);
+ usb_musb_init();
+ usb_ehci_init();
omap3beagle_flash_init();
}