From a30d46c042c8a17ef25de02f439fbd120ab8a8de Mon Sep 17 00:00:00 2001 From: David Brownell Date: Mon, 20 Oct 2008 23:46:28 +0200 Subject: [PATCH] mfd: twl4030 IRQ handling update - Move it into a separate file; clean and streamline it - Restructure the init code for reuse during secondary dispatch - Support both levels (primary, secondary) of IRQ dispatch - Use a workqueue for irq mask/unmask and trigger configuration Code for two subchips currently share that secondary handler code. One is the power subchip; its IRQs are now handled by this core, courtesy of this patch. The other is the GPIO module, which will be supported through a later patch. There are also minor changes to the header file, mostly related to GPIO support; nothing yet in mainline cares about those. A few references to OMAP-specific symbols are disabled; when they can all be removed, the TWL4030 support ceases being OMAP-specific. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren Signed-off-by: Samuel Ortiz --- drivers/mfd/Makefile | 2 +- drivers/mfd/twl4030-core.c | 421 +------------------- drivers/mfd/twl4030-irq.c | 743 ++++++++++++++++++++++++++++++++++++ include/linux/i2c/twl4030.h | 28 +- 4 files changed, 777 insertions(+), 417 deletions(-) create mode 100644 drivers/mfd/twl4030-irq.c diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 68e237b830a..0acefe8aff8 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -17,7 +17,7 @@ wm8350-objs := wm8350-core.o wm8350-regmap.o wm8350-gpio.o obj-$(CONFIG_MFD_WM8350) += wm8350.o obj-$(CONFIG_MFD_WM8350_I2C) += wm8350-i2c.o -obj-$(CONFIG_TWL4030_CORE) += twl4030-core.o +obj-$(CONFIG_TWL4030_CORE) += twl4030-core.o twl4030-irq.o obj-$(CONFIG_MFD_CORE) += mfd-core.o diff --git a/drivers/mfd/twl4030-core.c b/drivers/mfd/twl4030-core.c index fd9a0160202..dd843c4fbcc 100644 --- a/drivers/mfd/twl4030-core.c +++ b/drivers/mfd/twl4030-core.c @@ -27,15 +27,11 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#include #include #include -#include -#include -#include -#include #include #include +#include #include #include @@ -93,26 +89,6 @@ #define twl_has_usb() false #endif -static inline void activate_irq(int irq) -{ -#ifdef CONFIG_ARM - /* ARM requires an extra step to clear IRQ_NOREQUEST, which it - * sets on behalf of every irq_chip. Also sets IRQ_NOPROBE. - */ - set_irq_flags(irq, IRQF_VALID); -#else - /* same effect on other architectures */ - set_irq_noprobe(irq); -#endif -} - -/* Primary Interrupt Handler on TWL4030 Registers */ - -/* Register Definitions */ - -#define REG_PIH_ISR_P1 (0x1) -#define REG_PIH_ISR_P2 (0x2) -#define REG_PIH_SIR (0x3) /* Triton Core internal information (BEGIN) */ @@ -175,138 +151,6 @@ static inline void activate_irq(int irq) /*----------------------------------------------------------------------*/ -/** - * struct twl4030_mod_iregs - TWL module IMR/ISR regs to mask/clear at init - * @mod_no: TWL4030 module number (e.g., TWL4030_MODULE_GPIO) - * @sih_ctrl: address of module SIH_CTRL register - * @reg_cnt: number of IMR/ISR regs - * @imrs: pointer to array of TWL module interrupt mask register indices - * @isrs: pointer to array of TWL module interrupt status register indices - * - * Ties together TWL4030 modules and lists of IMR/ISR registers to mask/clear - * during twl_init_irq(). - */ -struct twl4030_mod_iregs { - const u8 mod_no; - const u8 sih_ctrl; - const u8 reg_cnt; - const u8 *imrs; - const u8 *isrs; -}; - -/* TWL4030 INT module interrupt mask registers */ -static const u8 __initconst twl4030_int_imr_regs[] = { - TWL4030_INT_PWR_IMR1, - TWL4030_INT_PWR_IMR2, -}; - -/* TWL4030 INT module interrupt status registers */ -static const u8 __initconst twl4030_int_isr_regs[] = { - TWL4030_INT_PWR_ISR1, - TWL4030_INT_PWR_ISR2, -}; - -/* TWL4030 INTERRUPTS module interrupt mask registers */ -static const u8 __initconst twl4030_interrupts_imr_regs[] = { - TWL4030_INTERRUPTS_BCIIMR1A, - TWL4030_INTERRUPTS_BCIIMR1B, - TWL4030_INTERRUPTS_BCIIMR2A, - TWL4030_INTERRUPTS_BCIIMR2B, -}; - -/* TWL4030 INTERRUPTS module interrupt status registers */ -static const u8 __initconst twl4030_interrupts_isr_regs[] = { - TWL4030_INTERRUPTS_BCIISR1A, - TWL4030_INTERRUPTS_BCIISR1B, - TWL4030_INTERRUPTS_BCIISR2A, - TWL4030_INTERRUPTS_BCIISR2B, -}; - -/* TWL4030 MADC module interrupt mask registers */ -static const u8 __initconst twl4030_madc_imr_regs[] = { - TWL4030_MADC_IMR1, - TWL4030_MADC_IMR2, -}; - -/* TWL4030 MADC module interrupt status registers */ -static const u8 __initconst twl4030_madc_isr_regs[] = { - TWL4030_MADC_ISR1, - TWL4030_MADC_ISR2, -}; - -/* TWL4030 keypad module interrupt mask registers */ -static const u8 __initconst twl4030_keypad_imr_regs[] = { - TWL4030_KEYPAD_KEYP_IMR1, - TWL4030_KEYPAD_KEYP_IMR2, -}; - -/* TWL4030 keypad module interrupt status registers */ -static const u8 __initconst twl4030_keypad_isr_regs[] = { - TWL4030_KEYPAD_KEYP_ISR1, - TWL4030_KEYPAD_KEYP_ISR2, -}; - -/* TWL4030 GPIO module interrupt mask registers */ -static const u8 __initconst twl4030_gpio_imr_regs[] = { - REG_GPIO_IMR1A, - REG_GPIO_IMR1B, - REG_GPIO_IMR2A, - REG_GPIO_IMR2B, - REG_GPIO_IMR3A, - REG_GPIO_IMR3B, -}; - -/* TWL4030 GPIO module interrupt status registers */ -static const u8 __initconst twl4030_gpio_isr_regs[] = { - REG_GPIO_ISR1A, - REG_GPIO_ISR1B, - REG_GPIO_ISR2A, - REG_GPIO_ISR2B, - REG_GPIO_ISR3A, - REG_GPIO_ISR3B, -}; - -/* TWL4030 modules that have IMR/ISR registers that must be masked/cleared */ -static const struct twl4030_mod_iregs __initconst twl4030_mod_regs[] = { - { - .mod_no = TWL4030_MODULE_INT, - .sih_ctrl = TWL4030_INT_PWR_SIH_CTRL, - .reg_cnt = ARRAY_SIZE(twl4030_int_imr_regs), - .imrs = twl4030_int_imr_regs, - .isrs = twl4030_int_isr_regs, - }, - { - .mod_no = TWL4030_MODULE_INTERRUPTS, - .sih_ctrl = TWL4030_INTERRUPTS_BCISIHCTRL, - .reg_cnt = ARRAY_SIZE(twl4030_interrupts_imr_regs), - .imrs = twl4030_interrupts_imr_regs, - .isrs = twl4030_interrupts_isr_regs, - }, - { - .mod_no = TWL4030_MODULE_MADC, - .sih_ctrl = TWL4030_MADC_SIH_CTRL, - .reg_cnt = ARRAY_SIZE(twl4030_madc_imr_regs), - .imrs = twl4030_madc_imr_regs, - .isrs = twl4030_madc_isr_regs, - }, - { - .mod_no = TWL4030_MODULE_KEYPAD, - .sih_ctrl = TWL4030_KEYPAD_KEYP_SIH_CTRL, - .reg_cnt = ARRAY_SIZE(twl4030_keypad_imr_regs), - .imrs = twl4030_keypad_imr_regs, - .isrs = twl4030_keypad_isr_regs, - }, - { - .mod_no = TWL4030_MODULE_GPIO, - .sih_ctrl = REG_GPIO_SIH_CTRL, - .reg_cnt = ARRAY_SIZE(twl4030_gpio_imr_regs), - .imrs = twl4030_gpio_imr_regs, - .isrs = twl4030_gpio_isr_regs, - }, -}; - -/*----------------------------------------------------------------*/ - /* is driver active, bound to a chip? */ static bool inuse; @@ -367,33 +211,6 @@ static struct twl4030mapping twl4030_map[TWL4030_MODULE_LAST + 1] = { /*----------------------------------------------------------------------*/ -/* - * TWL4030 doesn't have PIH mask, hence dummy function for mask - * and unmask of the (eight) interrupts reported at that level ... - * masking is only available from SIH (secondary) modules. - */ - -static void twl4030_i2c_ackirq(unsigned int irq) -{ -} - -static void twl4030_i2c_disableint(unsigned int irq) -{ -} - -static void twl4030_i2c_enableint(unsigned int irq) -{ -} - -static struct irq_chip twl4030_irq_chip = { - .name = "twl4030", - .ack = twl4030_i2c_ackirq, - .mask = twl4030_i2c_disableint, - .unmask = twl4030_i2c_enableint, -}; - -/*----------------------------------------------------------------------*/ - /* Exported Functions */ /** @@ -535,108 +352,11 @@ EXPORT_SYMBOL(twl4030_i2c_read_u8); /*----------------------------------------------------------------------*/ -static unsigned twl4030_irq_base; - -static struct completion irq_event; - -/* - * This thread processes interrupts reported by the Primary Interrupt Handler. - */ -static int twl4030_irq_thread(void *data) -{ - long irq = (long)data; - irq_desc_t *desc = irq_desc + irq; - static unsigned i2c_errors; - const static unsigned max_i2c_errors = 100; - - current->flags |= PF_NOFREEZE; - - while (!kthread_should_stop()) { - int ret; - int module_irq; - u8 pih_isr; - - /* Wait for IRQ, then read PIH irq status (also blocking) */ - wait_for_completion_interruptible(&irq_event); - - ret = twl4030_i2c_read_u8(TWL4030_MODULE_PIH, &pih_isr, - REG_PIH_ISR_P1); - if (ret) { - pr_warning("%s: I2C error %d reading PIH ISR\n", - DRIVER_NAME, ret); - if (++i2c_errors >= max_i2c_errors) { - printk(KERN_ERR "Maximum I2C error count" - " exceeded. Terminating %s.\n", - __func__); - break; - } - complete(&irq_event); - continue; - } - - /* these handlers deal with the relevant SIH irq status */ - local_irq_disable(); - for (module_irq = twl4030_irq_base; - pih_isr; - pih_isr >>= 1, module_irq++) { - if (pih_isr & 0x1) { - irq_desc_t *d = irq_desc + module_irq; - - d->handle_irq(module_irq, d); - } - } - local_irq_enable(); - - desc->chip->unmask(irq); - } - - return 0; -} - /* - * do_twl4030_irq() is the desc->handle method for the twl4030 interrupt. - * This is a chained interrupt, so there is no desc->action method for it. - * Now we need to query the interrupt controller in the twl4030 to determine - * which module is generating the interrupt request. However, we can't do i2c - * transactions in interrupt context, so we must defer that work to a kernel - * thread. All we do here is acknowledge and mask the interrupt and wakeup - * the kernel thread. + * NOTE: We know the first 8 IRQs after pdata->base_irq are + * for the PIH, and the next are for the PWR_INT SIH, since + * that's how twl_init_irq() sets things up. */ -static void do_twl4030_irq(unsigned int irq, irq_desc_t *desc) -{ - const unsigned int cpu = smp_processor_id(); - - /* - * Earlier this was desc->triggered = 1; - */ - desc->status |= IRQ_LEVEL; - - /* - * Acknowledge, clear _AND_ disable the interrupt. - */ - desc->chip->ack(irq); - - if (!desc->depth) { - kstat_cpu(cpu).irqs[irq]++; - - complete(&irq_event); - } -} - -static struct task_struct * __init start_twl4030_irq_thread(long irq) -{ - struct task_struct *thread; - - init_completion(&irq_event); - thread = kthread_run(twl4030_irq_thread, (void *)irq, "twl4030-irq"); - if (!thread) - pr_err("%s: could not create twl4030 irq %ld thread!\n", - DRIVER_NAME, irq); - - return thread; -} - -/*----------------------------------------------------------------------*/ static int add_children(struct twl4030_platform_data *pdata) { @@ -668,7 +388,7 @@ static int add_children(struct twl4030_platform_data *pdata) if (status == 0) { struct resource r = { - .start = TWL4030_PWRIRQ_CHG_PRES, + .start = pdata->irq_base + 8 + 1, .flags = IORESOURCE_IRQ, }; @@ -817,8 +537,7 @@ static int add_children(struct twl4030_platform_data *pdata) /* RTC module IRQ */ if (status == 0) { struct resource r = { - /* REVISIT don't hard-wire this stuff */ - .start = TWL4030_PWRIRQ_RTC, + .start = pdata->irq_base + 8 + 3, .flags = IORESOURCE_IRQ, }; @@ -863,7 +582,7 @@ static int add_children(struct twl4030_platform_data *pdata) if (status == 0) { struct resource r = { - .start = TWL4030_PWRIRQ_USB_PRES, + .start = pdata->irq_base + 8 + 2, .flags = IORESOURCE_IRQ, }; @@ -965,123 +684,17 @@ static void __init clocks_init(void) /*----------------------------------------------------------------------*/ -/** - * twl4030_i2c_clear_isr - clear TWL4030 SIH ISR regs via read + write - * @mod_no: TWL4030 module number - * @reg: register index to clear - * @cor: value of the _SIH_CTRL.COR bit (1 or 0) - * - * Either reads (cor == 1) or writes (cor == 0) to a TWL4030 interrupt - * status register to ensure that any prior interrupts are cleared. - * Returns the status from the I2C read operation. - */ -static int __init twl4030_i2c_clear_isr(u8 mod_no, u8 reg, u8 cor) -{ - u8 tmp; - - return (cor) ? twl4030_i2c_read_u8(mod_no, &tmp, reg) : - twl4030_i2c_write_u8(mod_no, 0xff, reg); -} - -/** - * twl4030_read_cor_bit - are TWL module ISRs cleared by reads or writes? - * @mod_no: TWL4030 module number - * @reg: register index to clear - * - * Returns 1 if the TWL4030 SIH interrupt status registers (ISRs) for - * the specified TWL module are cleared by reads, or 0 if cleared by - * writes. - */ -static int twl4030_read_cor_bit(u8 mod_no, u8 reg) -{ - u8 tmp = 0; - - WARN_ON(twl4030_i2c_read_u8(mod_no, &tmp, reg) < 0); - - tmp &= TWL4030_SIH_CTRL_COR_MASK; - tmp >>= __ffs(TWL4030_SIH_CTRL_COR_MASK); - - return tmp; -} - -/** - * twl4030_mask_clear_intrs - mask and clear all TWL4030 interrupts - * @t: pointer to twl4030_mod_iregs array - * @t_sz: ARRAY_SIZE(t) (starting at 1) - * - * Mask all TWL4030 interrupt mask registers (IMRs) and clear all - * interrupt status registers (ISRs). No return value, but will WARN if - * any I2C operations fail. - */ -static void __init twl4030_mask_clear_intrs(const struct twl4030_mod_iregs *t, - const u8 t_sz) -{ - int i, j; - - /* - * N.B. - further efficiency is possible here. Eight I2C - * operations on BCI and GPIO modules are avoidable if I2C - * burst read/write transactions were implemented. Would - * probably save about 1ms of boot time and a small amount of - * power. - */ - for (i = 0; i < t_sz; i++) { - const struct twl4030_mod_iregs tmr = t[i]; - int cor; - - /* Are ISRs cleared by reads or writes? */ - cor = twl4030_read_cor_bit(tmr.mod_no, tmr.sih_ctrl); - - for (j = 0; j < tmr.reg_cnt; j++) { - - /* Mask interrupts at the TWL4030 */ - WARN_ON(twl4030_i2c_write_u8(tmr.mod_no, 0xff, - tmr.imrs[j]) < 0); - - /* Clear TWL4030 ISRs */ - WARN_ON(twl4030_i2c_clear_isr(tmr.mod_no, - tmr.isrs[j], cor) < 0); - } - } -} - - -static void twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end) -{ - int i; - - /* - * Mask and clear all TWL4030 interrupts since initially we do - * not have any TWL4030 module interrupt handlers present - */ - twl4030_mask_clear_intrs(twl4030_mod_regs, - ARRAY_SIZE(twl4030_mod_regs)); - - twl4030_irq_base = irq_base; - - /* install an irq handler for each of the PIH modules */ - for (i = irq_base; i < irq_end; i++) { - set_irq_chip_and_handler(i, &twl4030_irq_chip, - handle_simple_irq); - activate_irq(i); - } - - /* install an irq handler to demultiplex the TWL4030 interrupt */ - set_irq_data(irq_num, start_twl4030_irq_thread(irq_num)); - set_irq_chained_handler(irq_num, do_twl4030_irq); -} - -/*----------------------------------------------------------------------*/ +int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end); +int twl_exit_irq(void); static int twl4030_remove(struct i2c_client *client) { unsigned i; + int status; - /* FIXME undo twl_init_irq() */ - if (twl4030_irq_base) { - dev_err(&client->dev, "can't yet clean up IRQs?\n"); - return -ENOSYS; - } + status = twl_exit_irq(); + if (status < 0) + return status; for (i = 0; i < TWL4030_NUM_SLAVES; i++) { struct twl4030_client *twl = &twl4030_modules[i]; @@ -1112,7 +725,7 @@ twl4030_probe(struct i2c_client *client, const struct i2c_device_id *id) return -EIO; } - if (inuse || twl4030_irq_base) { + if (inuse) { dev_dbg(&client->dev, "driver is already in use\n"); return -EBUSY; } @@ -1146,9 +759,9 @@ twl4030_probe(struct i2c_client *client, const struct i2c_device_id *id) if (client->irq && pdata->irq_base && pdata->irq_end > pdata->irq_base) { - twl_init_irq(client->irq, pdata->irq_base, pdata->irq_end); - dev_info(&client->dev, "IRQ %d chains IRQs %d..%d\n", - client->irq, pdata->irq_base, pdata->irq_end - 1); + status = twl_init_irq(client->irq, pdata->irq_base, pdata->irq_end); + if (status < 0) + goto fail; } status = add_children(pdata); diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c new file mode 100644 index 00000000000..fae868a8d49 --- /dev/null +++ b/drivers/mfd/twl4030-irq.c @@ -0,0 +1,743 @@ +/* + * twl4030-irq.c - TWL4030/TPS659x0 irq support + * + * Copyright (C) 2005-2006 Texas Instruments, Inc. + * + * Modifications to defer interrupt handling to a kernel thread: + * Copyright (C) 2006 MontaVista Software, Inc. + * + * Based on tlv320aic23.c: + * Copyright (c) by Kai Svahn + * + * Code cleanup and modifications to IRQ handler. + * by syed khasim + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include +#include +#include +#include + +#include + + +/* + * TWL4030 IRQ handling has two stages in hardware, and thus in software. + * The Primary Interrupt Handler (PIH) stage exposes status bits saying + * which Secondary Interrupt Handler (SIH) stage is raising an interrupt. + * SIH modules are more traditional IRQ components, which support per-IRQ + * enable/disable and trigger controls; they do most of the work. + * + * These chips are designed to support IRQ handling from two different + * I2C masters. Each has a dedicated IRQ line, and dedicated IRQ status + * and mask registers in the PIH and SIH modules. + * + * We set up IRQs starting at a platform-specified base, always starting + * with PIH and the SIH for PWR_INT and then usually adding GPIO: + * base + 0 .. base + 7 PIH + * base + 8 .. base + 15 SIH for PWR_INT + * base + 16 .. base + 33 SIH for GPIO + */ + +/* PIH register offsets */ +#define REG_PIH_ISR_P1 0x01 +#define REG_PIH_ISR_P2 0x02 +#define REG_PIH_SIR 0x03 /* for testing */ + + +/* Linux could (eventually) use either IRQ line */ +static int irq_line; + +struct sih { + char name[8]; + u8 module; /* module id */ + u8 control_offset; /* for SIH_CTRL */ + bool set_cor; + + u8 bits; /* valid in isr/imr */ + u8 bytes_ixr; /* bytelen of ISR/IMR/SIR */ + + u8 edr_offset; + u8 bytes_edr; /* bytelen of EDR */ + + /* SIR ignored -- set interrupt, for testing only */ + struct irq_data { + u8 isr_offset; + u8 imr_offset; + } mask[2]; + /* + 2 bytes padding */ +}; + +#define SIH_INITIALIZER(modname, nbits) \ + .module = TWL4030_MODULE_ ## modname, \ + .control_offset = TWL4030_ ## modname ## _SIH_CTRL, \ + .bits = nbits, \ + .bytes_ixr = DIV_ROUND_UP(nbits, 8), \ + .edr_offset = TWL4030_ ## modname ## _EDR, \ + .bytes_edr = DIV_ROUND_UP((2*(nbits)), 8), \ + .mask = { { \ + .isr_offset = TWL4030_ ## modname ## _ISR1, \ + .imr_offset = TWL4030_ ## modname ## _IMR1, \ + }, \ + { \ + .isr_offset = TWL4030_ ## modname ## _ISR2, \ + .imr_offset = TWL4030_ ## modname ## _IMR2, \ + }, }, + +/* register naming policies are inconsistent ... */ +#define TWL4030_INT_PWR_EDR TWL4030_INT_PWR_EDR1 +#define TWL4030_MODULE_KEYPAD_KEYP TWL4030_MODULE_KEYPAD +#define TWL4030_MODULE_INT_PWR TWL4030_MODULE_INT + + +/* Order in this table matches order in PIH_ISR. That is, + * BIT(n) in PIH_ISR is sih_modules[n]. + */ +static const struct sih sih_modules[6] = { + [0] = { + .name = "gpio", + .module = TWL4030_MODULE_GPIO, + .control_offset = REG_GPIO_SIH_CTRL, + .set_cor = true, + .bits = TWL4030_GPIO_MAX, + .bytes_ixr = 3, + /* Note: *all* of these IRQs default to no-trigger */ + .edr_offset = REG_GPIO_EDR1, + .bytes_edr = 5, + .mask = { { + .isr_offset = REG_GPIO_ISR1A, + .imr_offset = REG_GPIO_IMR1A, + }, { + .isr_offset = REG_GPIO_ISR1B, + .imr_offset = REG_GPIO_IMR1B, + }, }, + }, + [1] = { + .name = "keypad", + .set_cor = true, + SIH_INITIALIZER(KEYPAD_KEYP, 4) + }, + [2] = { + .name = "bci", + .module = TWL4030_MODULE_INTERRUPTS, + .control_offset = TWL4030_INTERRUPTS_BCISIHCTRL, + .bits = 12, + .bytes_ixr = 2, + .edr_offset = TWL4030_INTERRUPTS_BCIEDR1, + /* Note: most of these IRQs default to no-trigger */ + .bytes_edr = 3, + .mask = { { + .isr_offset = TWL4030_INTERRUPTS_BCIISR1A, + .imr_offset = TWL4030_INTERRUPTS_BCIIMR1A, + }, { + .isr_offset = TWL4030_INTERRUPTS_BCIISR1B, + .imr_offset = TWL4030_INTERRUPTS_BCIIMR1B, + }, }, + }, + [3] = { + .name = "madc", + SIH_INITIALIZER(MADC, 4) + }, + [4] = { + /* USB doesn't use the same SIH organization */ + .name = "usb", + }, + [5] = { + .name = "power", + .set_cor = true, + SIH_INITIALIZER(INT_PWR, 8) + }, + /* there are no SIH modules #6 or #7 ... */ +}; + +#undef TWL4030_MODULE_KEYPAD_KEYP +#undef TWL4030_MODULE_INT_PWR +#undef TWL4030_INT_PWR_EDR + +/*----------------------------------------------------------------------*/ + +static unsigned twl4030_irq_base; + +static struct completion irq_event; + +/* + * This thread processes interrupts reported by the Primary Interrupt Handler. + */ +static int twl4030_irq_thread(void *data) +{ + long irq = (long)data; + irq_desc_t *desc = irq_desc + irq; + static unsigned i2c_errors; + const static unsigned max_i2c_errors = 100; + + current->flags |= PF_NOFREEZE; + + while (!kthread_should_stop()) { + int ret; + int module_irq; + u8 pih_isr; + + /* Wait for IRQ, then read PIH irq status (also blocking) */ + wait_for_completion_interruptible(&irq_event); + + ret = twl4030_i2c_read_u8(TWL4030_MODULE_PIH, &pih_isr, + REG_PIH_ISR_P1); + if (ret) { + pr_warning("twl4030: I2C error %d reading PIH ISR\n", + ret); + if (++i2c_errors >= max_i2c_errors) { + printk(KERN_ERR "Maximum I2C error count" + " exceeded. Terminating %s.\n", + __func__); + break; + } + complete(&irq_event); + continue; + } + + /* these handlers deal with the relevant SIH irq status */ + local_irq_disable(); + for (module_irq = twl4030_irq_base; + pih_isr; + pih_isr >>= 1, module_irq++) { + if (pih_isr & 0x1) { + irq_desc_t *d = irq_desc + module_irq; + + /* These can't be masked ... always warn + * if we get any surprises. + */ + if (d->status & IRQ_DISABLED) + note_interrupt(module_irq, d, + IRQ_NONE); + else + d->handle_irq(module_irq, d); + } + } + local_irq_enable(); + + desc->chip->unmask(irq); + } + + return 0; +} + +/* + * handle_twl4030_pih() is the desc->handle method for the twl4030 interrupt. + * This is a chained interrupt, so there is no desc->action method for it. + * Now we need to query the interrupt controller in the twl4030 to determine + * which module is generating the interrupt request. However, we can't do i2c + * transactions in interrupt context, so we must defer that work to a kernel + * thread. All we do here is acknowledge and mask the interrupt and wakeup + * the kernel thread. + */ +static void handle_twl4030_pih(unsigned int irq, irq_desc_t *desc) +{ + /* Acknowledge, clear *AND* mask the interrupt... */ + desc->chip->ack(irq); + complete(&irq_event); +} + +static struct task_struct *start_twl4030_irq_thread(long irq) +{ + struct task_struct *thread; + + init_completion(&irq_event); + thread = kthread_run(twl4030_irq_thread, (void *)irq, "twl4030-irq"); + if (!thread) + pr_err("twl4030: could not create irq %ld thread!\n", irq); + + return thread; +} + +/*----------------------------------------------------------------------*/ + +/* + * twl4030_init_sih_modules() ... start from a known state where no + * IRQs will be coming in, and where we can quickly enable them then + * handle them as they arrive. Mask all IRQs: maybe init SIH_CTRL. + * + * NOTE: we don't touch EDR registers here; they stay with hardware + * defaults or whatever the last value was. Note that when both EDR + * bits for an IRQ are clear, that's as if its IMR bit is set... + */ +static int twl4030_init_sih_modules(unsigned line) +{ + const struct sih *sih; + u8 buf[4]; + int i; + int status; + + /* line 0 == int1_n signal; line 1 == int2_n signal */ + if (line > 1) + return -EINVAL; + + irq_line = line; + + /* disable all interrupts on our line */ + memset(buf, 0xff, sizeof buf); + sih = sih_modules; + for (i = 0; i < ARRAY_SIZE(sih_modules); i++, sih++) { + + /* skip USB -- it's funky */ + if (!sih->bytes_ixr) + continue; + + status = twl4030_i2c_write(sih->module, buf, + sih->mask[line].imr_offset, sih->bytes_ixr); + if (status < 0) + pr_err("twl4030: err %d initializing %s %s\n", + status, sih->name, "IMR"); + + /* Maybe disable "exclusive" mode; buffer second pending irq; + * set Clear-On-Read (COR) bit. + * + * NOTE that sometimes COR polarity is documented as being + * inverted: for MADC and BCI, COR=1 means "clear on write". + * And for PWR_INT it's not documented... + */ + if (sih->set_cor) { + status = twl4030_i2c_write_u8(sih->module, + TWL4030_SIH_CTRL_COR_MASK, + sih->control_offset); + if (status < 0) + pr_err("twl4030: err %d initializing %s %s\n", + status, sih->name, "SIH_CTRL"); + } + } + + sih = sih_modules; + for (i = 0; i < ARRAY_SIZE(sih_modules); i++, sih++) { + u8 rxbuf[4]; + int j; + + /* skip USB */ + if (!sih->bytes_ixr) + continue; + + /* Clear pending interrupt status. Either the read was + * enough, or we need to write those bits. Repeat, in + * case an IRQ is pending (PENDDIS=0) ... that's not + * uncommon with PWR_INT.PWRON. + */ + for (j = 0; j < 2; j++) { + status = twl4030_i2c_read(sih->module, rxbuf, + sih->mask[line].isr_offset, sih->bytes_ixr); + if (status < 0) + pr_err("twl4030: err %d initializing %s %s\n", + status, sih->name, "ISR"); + + if (!sih->set_cor) + status = twl4030_i2c_write(sih->module, buf, + sih->mask[line].isr_offset, + sih->bytes_ixr); + /* else COR=1 means read sufficed. + * (for most SIH modules...) + */ + } + } + + return 0; +} + +static inline void activate_irq(int irq) +{ +#ifdef CONFIG_ARM + /* ARM requires an extra step to clear IRQ_NOREQUEST, which it + * sets on behalf of every irq_chip. Also sets IRQ_NOPROBE. + */ + set_irq_flags(irq, IRQF_VALID); +#else + /* same effect on other architectures */ + set_irq_noprobe(irq); +#endif +} + +/*----------------------------------------------------------------------*/ + +static DEFINE_SPINLOCK(sih_agent_lock); + +static struct workqueue_struct *wq; + +struct sih_agent { + int irq_base; + const struct sih *sih; + + u32 imr; + bool imr_change_pending; + struct work_struct mask_work; + + u32 edge_change; + struct work_struct edge_work; +}; + +static void twl4030_sih_do_mask(struct work_struct *work) +{ + struct sih_agent *agent; + const struct sih *sih; + union { + u8 bytes[4]; + u32 word; + } imr; + int status; + + agent = container_of(work, struct sih_agent, mask_work); + + /* see what work we have */ + spin_lock_irq(&sih_agent_lock); + if (agent->imr_change_pending) { + sih = agent->sih; + /* byte[0] gets overwritten as we write ... */ + imr.word = cpu_to_le32(agent->imr << 8); + agent->imr_change_pending = false; + } else + sih = NULL; + spin_unlock_irq(&sih_agent_lock); + if (!sih) + return; + + /* write the whole mask ... simpler than subsetting it */ + status = twl4030_i2c_write(sih->module, imr.bytes, + sih->mask[irq_line].imr_offset, sih->bytes_ixr); + if (status) + pr_err("twl4030: %s, %s --> %d\n", __func__, + "write", status); +} + +static void twl4030_sih_do_edge(struct work_struct *work) +{ + struct sih_agent *agent; + const struct sih *sih; + u8 bytes[6]; + u32 edge_change; + int status; + + agent = container_of(work, struct sih_agent, edge_work); + + /* see what work we have */ + spin_lock_irq(&sih_agent_lock); + edge_change = agent->edge_change; + agent->edge_change = 0;; + sih = edge_change ? agent->sih : NULL; + spin_unlock_irq(&sih_agent_lock); + if (!sih) + return; + + /* Read, reserving first byte for write scratch. Yes, this + * could be cached for some speedup ... but be careful about + * any processor on the other IRQ line, EDR registers are + * shared. + */ + status = twl4030_i2c_read(sih->module, bytes + 1, + sih->edr_offset, sih->bytes_edr); + if (status) { + pr_err("twl4030: %s, %s --> %d\n", __func__, + "read", status); + return; + } + + /* Modify only the bits we know must change */ + while (edge_change) { + int i = fls(edge_change) - 1; + struct irq_desc *d = irq_desc + i + agent->irq_base; + int byte = 1 + (i >> 2); + int off = (i & 0x3) * 2; + + bytes[byte] &= ~(0x03 << off); + + spin_lock_irq(&d->lock); + if (d->status & IRQ_TYPE_EDGE_RISING) + bytes[byte] |= BIT(off + 1); + if (d->status & IRQ_TYPE_EDGE_FALLING) + bytes[byte] |= BIT(off + 0); + spin_unlock_irq(&d->lock); + + edge_change &= ~BIT(i); + } + + /* Write */ + status = twl4030_i2c_write(sih->module, bytes, + sih->edr_offset, sih->bytes_edr); + if (status) + pr_err("twl4030: %s, %s --> %d\n", __func__, + "write", status); +} + +/*----------------------------------------------------------------------*/ + +/* + * All irq_chip methods get issued from code holding irq_desc[irq].lock, + * which can't perform the underlying I2C operations (because they sleep). + * So we must hand them off to a thread (workqueue) and cope with asynch + * completion, potentially including some re-ordering, of these requests. + */ + +static void twl4030_sih_mask(unsigned irq) +{ + struct sih_agent *sih = get_irq_chip_data(irq); + unsigned long flags; + + spin_lock_irqsave(&sih_agent_lock, flags); + sih->imr |= BIT(irq - sih->irq_base); + sih->imr_change_pending = true; + queue_work(wq, &sih->mask_work); + spin_unlock_irqrestore(&sih_agent_lock, flags); +} + +static void twl4030_sih_unmask(unsigned irq) +{ + struct sih_agent *sih = get_irq_chip_data(irq); + unsigned long flags; + + spin_lock_irqsave(&sih_agent_lock, flags); + sih->imr &= ~BIT(irq - sih->irq_base); + sih->imr_change_pending = true; + queue_work(wq, &sih->mask_work); + spin_unlock_irqrestore(&sih_agent_lock, flags); +} + +static int twl4030_sih_set_type(unsigned irq, unsigned trigger) +{ + struct sih_agent *sih = get_irq_chip_data(irq); + struct irq_desc *desc = irq_desc + irq; + unsigned long flags; + + if (trigger & ~(IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) + return -EINVAL; + + spin_lock_irqsave(&sih_agent_lock, flags); + if ((desc->status & IRQ_TYPE_SENSE_MASK) != trigger) { + desc->status &= ~IRQ_TYPE_SENSE_MASK; + desc->status |= trigger; + sih->edge_change |= BIT(irq - sih->irq_base); + queue_work(wq, &sih->edge_work); + } + spin_unlock_irqrestore(&sih_agent_lock, flags); + return 0; +} + +static struct irq_chip twl4030_sih_irq_chip = { + .name = "twl4030", + .mask = twl4030_sih_mask, + .unmask = twl4030_sih_unmask, + .set_type = twl4030_sih_set_type, +}; + +/*----------------------------------------------------------------------*/ + +static inline int sih_read_isr(const struct sih *sih) +{ + int status; + union { + u8 bytes[4]; + u32 word; + } isr; + + /* FIXME need retry-on-error ... */ + + isr.word = 0; + status = twl4030_i2c_read(sih->module, isr.bytes, + sih->mask[irq_line].isr_offset, sih->bytes_ixr); + + return (status < 0) ? status : le32_to_cpu(isr.word); +} + +/* + * Generic handler for SIH interrupts ... we "know" this is called + * in task context, with IRQs enabled. + */ +static void handle_twl4030_sih(unsigned irq, struct irq_desc *desc) +{ + struct sih_agent *agent = get_irq_data(irq); + const struct sih *sih = agent->sih; + int isr; + + /* reading ISR acks the IRQs, using clear-on-read mode */ + local_irq_enable(); + isr = sih_read_isr(sih); + local_irq_disable(); + + if (isr < 0) { + pr_err("twl4030: %s SIH, read ISR error %d\n", + sih->name, isr); + /* REVISIT: recover; eventually mask it all, etc */ + return; + } + + while (isr) { + irq = fls(isr); + irq--; + isr &= ~BIT(irq); + + if (irq < sih->bits) + generic_handle_irq(agent->irq_base + irq); + else + pr_err("twl4030: %s SIH, invalid ISR bit %d\n", + sih->name, irq); + } +} + +static unsigned twl4030_irq_next; + +/* returns the first IRQ used by this SIH bank, + * or negative errno + */ +int twl4030_sih_setup(int module) +{ + int sih_mod; + const struct sih *sih = NULL; + struct sih_agent *agent; + int i, irq; + int status = -EINVAL; + unsigned irq_base = twl4030_irq_next; + + /* only support modules with standard clear-on-read for now */ + for (sih_mod = 0, sih = sih_modules; + sih_mod < ARRAY_SIZE(sih_modules); + sih_mod++, sih++) { + if (sih->module == module && sih->set_cor) { + if (!WARN((irq_base + sih->bits) > NR_IRQS, + "irq %d for %s too big\n", + irq_base + sih->bits, + sih->name)) + status = 0; + break; + } + } + if (status < 0) + return status; + + agent = kzalloc(sizeof *agent, GFP_KERNEL); + if (!agent) + return -ENOMEM; + + status = 0; + + agent->irq_base = irq_base; + agent->sih = sih; + agent->imr = ~0; + INIT_WORK(&agent->mask_work, twl4030_sih_do_mask); + INIT_WORK(&agent->edge_work, twl4030_sih_do_edge); + + for (i = 0; i < sih->bits; i++) { + irq = irq_base + i; + + set_irq_chip_and_handler(irq, &twl4030_sih_irq_chip, + handle_edge_irq); + set_irq_chip_data(irq, agent); + activate_irq(irq); + } + + status = irq_base; + twl4030_irq_next += i; + + /* replace generic PIH handler (handle_simple_irq) */ + irq = sih_mod + twl4030_irq_base; + set_irq_data(irq, agent); + set_irq_chained_handler(irq, handle_twl4030_sih); + + pr_info("twl4030: %s (irq %d) chaining IRQs %d..%d\n", sih->name, + irq, irq_base, twl4030_irq_next - 1); + + return status; +} + +/* FIXME need a call to reverse twl4030_sih_setup() ... */ + + +/*----------------------------------------------------------------------*/ + +/* FIXME pass in which interrupt line we'll use ... */ +#define twl_irq_line 0 + +int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end) +{ + static struct irq_chip twl4030_irq_chip; + + int status; + int i; + struct task_struct *task; + + /* + * Mask and clear all TWL4030 interrupts since initially we do + * not have any TWL4030 module interrupt handlers present + */ + status = twl4030_init_sih_modules(twl_irq_line); + if (status < 0) + return status; + + wq = create_singlethread_workqueue("twl4030-irqchip"); + if (!wq) { + pr_err("twl4030: workqueue FAIL\n"); + return -ESRCH; + } + + twl4030_irq_base = irq_base; + + /* install an irq handler for each of the SIH modules; + * clone dummy irq_chip since PIH can't *do* anything + */ + twl4030_irq_chip = dummy_irq_chip; + twl4030_irq_chip.name = "twl4030"; + + twl4030_sih_irq_chip.ack = dummy_irq_chip.ack; + + for (i = irq_base; i < irq_end; i++) { + set_irq_chip_and_handler(i, &twl4030_irq_chip, + handle_simple_irq); + activate_irq(i); + } + twl4030_irq_next = i; + pr_info("twl4030: %s (irq %d) chaining IRQs %d..%d\n", "PIH", + irq_num, irq_base, twl4030_irq_next - 1); + + /* ... and the PWR_INT module ... */ + status = twl4030_sih_setup(TWL4030_MODULE_INT); + if (status < 0) { + pr_err("twl4030: sih_setup PWR INT --> %d\n", status); + goto fail; + } + + /* install an irq handler to demultiplex the TWL4030 interrupt */ + task = start_twl4030_irq_thread(irq_num); + if (!task) { + pr_err("twl4030: irq thread FAIL\n"); + status = -ESRCH; + goto fail; + } + + set_irq_data(irq_num, task); + set_irq_chained_handler(irq_num, handle_twl4030_pih); + + return status; + +fail: + for (i = irq_base; i < irq_end; i++) + set_irq_chip_and_handler(i, NULL, NULL); + destroy_workqueue(wq); + wq = NULL; + return status; +} + +int twl_exit_irq(void) +{ + /* FIXME undo twl_init_irq() */ + if (twl4030_irq_base) { + pr_err("twl4030: can't yet clean up IRQs?\n"); + return -ENOSYS; + } + return 0; +} diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h index cdb453162a9..fb604dcd38f 100644 --- a/include/linux/i2c/twl4030.h +++ b/include/linux/i2c/twl4030.h @@ -228,6 +228,12 @@ struct twl4030_gpio_platform_data { int gpio_base; unsigned irq_base, irq_end; + /* package the two LED signals as output-only GPIOs? */ + bool use_leds; + + /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ + u8 mmc_cd; + /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup * should be enabled. Else, if that bit is set in "pulldowns", * that pulldown is enabled. Don't waste power by letting any @@ -277,6 +283,8 @@ struct twl4030_platform_data { /*----------------------------------------------------------------------*/ +int twl4030_sih_setup(int module); + /* * FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the * IRQ data to subsidiary devices using platform device resources. @@ -291,16 +299,16 @@ struct twl4030_platform_data { #define TWL4030_MODIRQ_BCI (TWL4030_IRQ_BASE + 2) #define TWL4030_MODIRQ_MADC (TWL4030_IRQ_BASE + 3) /* #define TWL4030_MODIRQ_USB (TWL4030_IRQ_BASE + 4) */ -#define TWL4030_MODIRQ_PWR (TWL4030_IRQ_BASE + 5) +/* #define TWL4030_MODIRQ_PWR (TWL4030_IRQ_BASE + 5) */ #define TWL4030_PWRIRQ_PWRBTN (TWL4030_PWR_IRQ_BASE + 0) -#define TWL4030_PWRIRQ_CHG_PRES (TWL4030_PWR_IRQ_BASE + 1) -#define TWL4030_PWRIRQ_USB_PRES (TWL4030_PWR_IRQ_BASE + 2) -#define TWL4030_PWRIRQ_RTC (TWL4030_PWR_IRQ_BASE + 3) -#define TWL4030_PWRIRQ_HOT_DIE (TWL4030_PWR_IRQ_BASE + 4) -#define TWL4030_PWRIRQ_PWROK_TIMEOUT (TWL4030_PWR_IRQ_BASE + 5) -#define TWL4030_PWRIRQ_MBCHG (TWL4030_PWR_IRQ_BASE + 6) -#define TWL4030_PWRIRQ_SC_DETECT (TWL4030_PWR_IRQ_BASE + 7) +/* #define TWL4030_PWRIRQ_CHG_PRES (TWL4030_PWR_IRQ_BASE + 1) */ +/* #define TWL4030_PWRIRQ_USB_PRES (TWL4030_PWR_IRQ_BASE + 2) */ +/* #define TWL4030_PWRIRQ_RTC (TWL4030_PWR_IRQ_BASE + 3) */ +/* #define TWL4030_PWRIRQ_HOT_DIE (TWL4030_PWR_IRQ_BASE + 4) */ +/* #define TWL4030_PWRIRQ_PWROK_TIMEOUT (TWL4030_PWR_IRQ_BASE + 5) */ +/* #define TWL4030_PWRIRQ_MBCHG (TWL4030_PWR_IRQ_BASE + 6) */ +/* #define TWL4030_PWRIRQ_SC_DETECT (TWL4030_PWR_IRQ_BASE + 7) */ /* Rest are unsued currently*/ @@ -317,17 +325,13 @@ struct twl4030_platform_data { /* TWL4030 GPIO interrupt definitions */ #define TWL4030_GPIO_IRQ_NO(n) (TWL4030_GPIO_IRQ_BASE + (n)) -#define TWL4030_GPIO_IS_ENABLE 1 /* * Exported TWL4030 GPIO APIs * * WARNING -- use standard GPIO and IRQ calls instead; these will vanish. */ -int twl4030_get_gpio_datain(int gpio); -int twl4030_request_gpio(int gpio); int twl4030_set_gpio_debounce(int gpio, int enable); -int twl4030_free_gpio(int gpio); #if defined(CONFIG_TWL4030_BCI_BATTERY) || \ defined(CONFIG_TWL4030_BCI_BATTERY_MODULE) -- 2.41.0