Nicolas Pitre [Tue, 9 Sep 2008 19:54:13 +0000 (15:54 -0400)]
[ARM] make page_to_dma() highmem aware
If a machine class has a custom __virt_to_bus() implementation then it
must provide a __arch_page_to_dma() implementation as well which is
_not_ based on page_address() to support highmem.
This patch fixes existing __arch_page_to_dma() and provide a default
implementation otherwise. The default implementation for highmem is
based on __pfn_to_bus() which is defined only when no custom
__virt_to_bus() is provided by the machine class.
That leaves only ebsa110 and footbridge which cannot support highmem
until they provide their own __arch_page_to_dma() implementation.
But highmem support on those legacy platforms with limited memory is
certainly not a priority.
Nicolas Pitre [Fri, 13 Mar 2009 02:52:09 +0000 (22:52 -0400)]
[ARM] introduce dma_cache_maint_page()
This is a helper to be used by the DMA mapping API to handle cache
maintenance for memory identified by a page structure instead of a
virtual address. Those pages may or may not be highmem pages, and
when they're highmem pages, they may or may not be virtually mapped.
When they're not mapped then there is no L1 cache to worry about. But
even in that case the L2 cache must be processed since unmapped highmem
pages can still be L2 cached.
Nicolas Pitre [Thu, 5 Mar 2009 03:49:41 +0000 (22:49 -0500)]
highmem: atomic highmem kmap page pinning
Most ARM machines have a non IO coherent cache, meaning that the
dma_map_*() set of functions must clean and/or invalidate the affected
memory manually before DMA occurs. And because the majority of those
machines have a VIVT cache, the cache maintenance operations must be
performed using virtual
addresses.
When a highmem page is kunmap'd, its mapping (and cache) remains in place
in case it is kmap'd again. However if dma_map_page() is then called with
such a page, some cache maintenance on the remaining mapping must be
performed. In that case, page_address(page) is non null and we can use
that to synchronize the cache.
It is unlikely but still possible for kmap() to race and recycle the
virtual address obtained above, and use it for another page before some
on-going cache invalidation loop in dma_map_page() is done. In that case,
the new mapping could end up with dirty cache lines for another page,
and the unsuspecting cache invalidation loop in dma_map_page() might
simply discard those dirty cache lines resulting in data loss.
For example, let's consider this sequence of events:
- dma_map_page(..., DMA_FROM_DEVICE) is called on a highmem page.
--> - vaddr = page_address(page) is non null. In this case
it is likely that the page has valid cache lines
associated with vaddr. Remember that the cache is VIVT.
--> for (i = vaddr; i < vaddr + PAGE_SIZE; i += 32)
invalidate_cache_line(i);
*** preemption occurs in the middle of the loop above ***
- kmap_high() is called for a different page.
--> - last_pkmap_nr wraps to zero and flush_all_zero_pkmaps()
is called. The pkmap_count value for the page passed
to dma_map_page() above happens to be 1, so the page
is unmapped. But prior to that, flush_cache_kmaps()
cleared the cache for it. So far so good.
- A fresh pkmap entry is assigned for this kmap request.
The Murphy law says this pkmap entry will eventually
happen to use the same vaddr as the one which used to
belong to the other page being processed by
dma_map_page() in the preempted thread above.
- The kmap_high() caller start dirtying the cache using the
just assigned virtual mapping for its page.
*** the first thread is rescheduled ***
- The for(...) loop is resumed, but now cached
data belonging to a different physical page is
being discarded !
And this is not only a preemption issue as ARM can be SMP as well,
making the above scenario just as likely. Hence the need for some kind
of pkmap page pinning which can be used in any context, primarily for
the benefit of dma_map_page() on ARM.
This provides the necessary interface to cope with the above issue if
ARCH_NEEDS_KMAP_HIGH_GET is defined, otherwise the resulting code is
unchanged.
Signed-off-by: Nicolas Pitre <nico@marvell.com> Reviewed-by: MinChan Kim <minchan.kim@gmail.com> Acked-by: Andrew Morton <akpm@linux-foundation.org>
Nicolas Pitre [Mon, 15 Sep 2008 20:44:55 +0000 (16:44 -0400)]
[ARM] kmap support
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Nicolas Pitre [Tue, 16 Sep 2008 17:05:53 +0000 (13:05 -0400)]
[ARM] fixmap support
This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.
We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000. Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.
However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.
So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.
The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Ingo Molnar [Thu, 12 Mar 2009 14:15:31 +0000 (15:15 +0100)]
kconfig: improve seed in randconfig
'make randconfig' uses glibc's rand function, and the seed of
that PRNG is set via:
srand(time(NULL));
But 'time()' only increases once every second - freezing the
randconfig result within a single second.
My Nehalem testbox does randconfig much faster than 1 second
and i have a few scripts that do 'randconfig until condition X'
loops.
Those scripts currently waste a lot of CPU time due to randconfig
changing its seed only once per second currently.
Change the seed to be micrseconds based. (I checked the statistical
spread of the seed - the now.tv_sec*now.tv_usec multiplication
there further improves it.)
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Roman Zippel <zippel@linux-m68k.org>
[sam: fix for systems where usec is zero - noticed by Geert Uytterhoeven] Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sam Ravnborg [Sun, 15 Mar 2009 10:05:12 +0000 (11:05 +0100)]
kconfig: fix randconfig for choice blocks
Ingo Molnar reported that 'make randconfig' was not covering
choice blocks properly, resulting in certain config options
being left out of randconfig testing altogether.
With the following patch we:
- properly randomize choice value for normal choice blocks
- properly randomize for multi choice blocks
- added several comments to explain what is going on
The root cause of the bug was that SYMBOL_VALID was set on the
symbol representing the choice block so clearing this did
the trick initially.
But testign revealed a few more issues that is now fixed.
Reported-by: Ingo Molnar <mingo@elte.hu> Cc: Ingo Molnar <mingo@elte.hu> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus Torvalds [Sun, 15 Mar 2009 20:34:56 +0000 (13:34 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
Robert Jarzmik [Sun, 15 Mar 2009 13:10:54 +0000 (14:10 +0100)]
ASoC: Allow choice of ac97 gpio reset line
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dmitry Artamonow [Sun, 15 Mar 2009 18:09:50 +0000 (19:09 +0100)]
[ARM] 5424/1: h3600: clean up mtd partitions table
Right now iPaq h3600's default MTD partitions table is a mess. It has
two #ifdefs with #else, giving total 3 variants, depending on your
kernel config. Replace all this with simple two-partitions scheme
(bootloader + rootfs), that used by both shipped WindowsCE and
most of the linux distributions (Familiar, Angstrom)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Felix Blyakher [Thu, 12 Mar 2009 14:33:37 +0000 (09:33 -0500)]
Fix xfs debug build breakage by pushing xfs_error.h after
xfs_mount.h, which it depends on.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Alex Elder <aelder@sgi.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
Alexander Duyck [Sun, 15 Mar 2009 05:26:40 +0000 (22:26 -0700)]
igb: remove ASPM L0s workaround
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yinghai Lu [Mon, 9 Mar 2009 08:15:57 +0000 (01:15 -0700)]
x86: put initial_pg_tables into .bss
Impact: makes vmlinux section information more useful
Don't use ram after _end blindly for pagetables. aka init pages is before _end
put those pg table into .bss
[Adapted to use brk segment - Jeremy]
v2: keep initial page table up to 512M only.
v4: put initial page tables just before _end
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add RESERVE_BRK(name, size) macro to reserve space in the brk
area. This should be a conservative (ie, larger) estimate of
how much space might possibly be required from the brk area.
Any unused space will be freed, so there's no real downside
on making the reservation too large (within limits).
The name should be unique within a given file, and somewhat
descriptive.
The C definition of RESERVE_BRK() ends up being more complex than
one would expect to work around a cluster of gcc infelicities:
The first attempt was to simply try putting __section(.brk_reservation)
on a variable. This doesn't work because it ends up making it a
@progbits section, which gets actual space allocated in the vmlinux
executable.
The second attempt was to emit the space into a section using asm,
but gcc doesn't allow arguments to be passed to file-level asm()
statements, making it hard to pass in the size.
The final attempt is to wrap the asm() in a function to allow
it to have arguments, and put the function itself into the
.discard section, which vmlinux*.lds drops entirely from the
emitted vmlinux.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Yinghai Lu [Thu, 12 Mar 2009 23:04:42 +0000 (16:04 -0700)]
x86-32: compute initial mapping size more accurately
Impact: simplification
We only need to map the kernel in head_32.S, not the whole of
lowmem. We use 512MB as a reasonable (but arbitrary) limit on
the maximum size of the kernel image.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x86-32: use brk segment for allocating initial kernel pagetable
Impact: use new interface instead of previous ad hoc implementation
Rather than having special purpose init_pg_table_start/end variables
to delimit the kernel pagetable built by head_32.S, just use the brk
mechanism to extend the bss for the new pagetable.
This patch removes init_pg_table_start/end and pg0, defines __brk_base
(which is page-aligned and immediately follows _end), initializes
the brk region to start there, and uses it for the 32-bit pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Sun, 15 Mar 2009 00:19:51 +0000 (17:19 -0700)]
x86: move brk initialization out of #ifdef CONFIG_BLK_DEV_INITRD
Impact: build fix
The brk initialization functions were incorrectly located inside
an #ifdef CONFIG_VLK_DEV_INITRD block, causing the obvious build failure in
minimal configurations.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
x86: add brk allocation for very, very early allocations
Impact: new interface
Add a brk()-like allocator which effectively extends the bss in order
to allow very early code to do dynamic allocations. This is better than
using statically allocated arrays for data in subsystems which may never
get used.
The space for brk allocations is in the bss ELF segment, so that the
space is mapped properly by the code which maps the kernel, and so
that bootloaders keep the space free rather than putting a ramdisk or
something into it.
The bss itself, delimited by __bss_stop, ends before the brk area
(__brk_base to __brk_limit). The kernel text, data and bss is reserved
up to __bss_stop.
Any brk-allocated data is reserved separately just before the kernel
pagetable is built, as that code allocates from unreserved spaces
in the e820 map, potentially allocating from any unused brk memory.
Ultimately any unused memory in the brk area is used in the general
kernel memory pool.
Initially the brk space is set to 1MB, which is probably much larger
than any user needs (the largest current user is i386 head_32.S's code
to build the pagetables to map the kernel, which can get fairly large
with a big kernel image and no PSE support). So long as the system
has sufficient memory for the bootloader to reserve the kernel+1MB brk,
there are no bad effects resulting from an over-large brk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x86: make section delimiter symbols part of their section
Impact: cleanup
Move the symbols delimiting a section part of the section
(section relative) rather than absolute. This avoids any
unexpected gaps between the section-start symbol and the first
data in the section, which could be caused by implicit
alignment of the section data. It also makes the general
form of vmlinux_64.lds.S consistent with vmlinux_32.lds.S.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Dhananjay Phadke [Fri, 13 Mar 2009 14:52:05 +0000 (14:52 +0000)]
netxen: add receive side scaling (rss) support
This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.
The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 13 Mar 2009 14:52:03 +0000 (14:52 +0000)]
netxen: sanitize variable names
o remove max_ prefix from ring sizes, since they don't really
represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
rx ring of 10 gig ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Likely [Mon, 9 Mar 2009 12:42:24 +0000 (13:42 +0100)]
Fix Xilinx SystemACE driver to handle empty CF slot
The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
un'ichi Nomura [Mon, 9 Mar 2009 09:40:52 +0000 (10:40 +0100)]
block: Add gfp_mask parameter to bio_integrity_clone()
Stricter gfp_mask might be required for clone allocation.
For example, request-based dm may clone bio in interrupt context
so it has to use GFP_ATOMIC.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com> Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
PJ Waskiewicz [Fri, 13 Mar 2009 22:15:54 +0000 (22:15 +0000)]
ixgbe: Add documentation for the driver
Documentation for the ixgbe driver in the kernel docs area is missing.
This adds that documentation.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:15:31 +0000 (22:15 +0000)]
ixgbe: Cleanup some whitespace issues, fixup and add some comments
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PJ Waskiewicz [Fri, 13 Mar 2009 22:15:10 +0000 (22:15 +0000)]
ixgbe: Two small fixes for 82599 when bringing the device down and for WoL
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:14:50 +0000 (22:14 +0000)]
ixgbe: Add a few safety nets for register writes and descriptor cleanups
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:14:30 +0000 (22:14 +0000)]
ixgbe: Cleanup on the Rx init path
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:14:10 +0000 (22:14 +0000)]
ixgbe: Fix the Tx clean logic to return proper status
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:13:49 +0000 (22:13 +0000)]
ixgbe: fix bug with napi add before request_irq
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 13 Mar 2009 22:13:28 +0000 (22:13 +0000)]
ixgbe: Fix interrupt configuration for 82599
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PJ Waskiewicz [Fri, 13 Mar 2009 22:13:08 +0000 (22:13 +0000)]
ixgbe: Disable DROP_EN for Rx queues
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PJ Waskiewicz [Fri, 13 Mar 2009 22:12:48 +0000 (22:12 +0000)]
ixgbe: Fix an accounting problem when the Rx FIFO is full
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PJ Waskiewicz [Fri, 13 Mar 2009 22:12:29 +0000 (22:12 +0000)]
ixgbe: Fix get_supported_physical_layer() due to new 82599 PHY types
A purely cosmetic change. Report which physical layer is present, instead
of PHY unknown. 82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:42:35 +0000 (20:42 +0000)]
igb: add support for 82576 quad copper adapter
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:42:15 +0000 (20:42 +0000)]
igb: add support for another dual port 82576 non-security nic
Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:41:55 +0000 (20:41 +0000)]
igb: correct typo that was setting vfta mask to 1
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.
This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:41:37 +0000 (20:41 +0000)]
igb: add PF to pool
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.
This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:41:17 +0000 (20:41 +0000)]
igb: support wol on second port
We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:40:58 +0000 (20:40 +0000)]
igb: resolve warning of unused adapter struct
If DCA is undefined then the adapter struct becomes unnecessary. To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 13 Mar 2009 20:40:38 +0000 (20:40 +0000)]
igb: remove netif running call from igb_poll
The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24. It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Sosnowski [Fri, 13 Mar 2009 20:40:21 +0000 (20:40 +0000)]
igb: switch to new dca API
With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().
Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Mar 2009 19:02:21 +0000 (12:02 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Mark Eins: Fix configuration.
MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
Linus Torvalds [Sat, 14 Mar 2009 19:00:42 +0000 (12:00 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: add workaround for Samsung DB-P70
libata: Keep shadow last_ctl up to date during resets
sata_mv: fix MSI irq race condition
Linus Torvalds [Sat, 14 Mar 2009 19:00:18 +0000 (12:00 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
SUNRPC: Fix an Oops due to socket not set up yet...
Bug 11061, NFS mounts dropped
NFS: Handle -ESTALE error in access()
NLM: Fix GRANT callback address comparison when IPv6 is enabled
NLM: Shrink the IPv4-only version of nlm_cmp_addr()
NFSv3: Fix posix ACL code
NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
SUNRPC: Tighten up the task locking rules in __rpc_execute()
Linus Torvalds [Sat, 14 Mar 2009 18:59:22 +0000 (11:59 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Use xs->bucket to set xattr value outside
ocfs2: Fix a bug found by sparse check.
ocfs2: tweak to get the maximum inline data size with xattr
ocfs2: reserve xattr block for new directory with inline data
Linus Torvalds [Sat, 14 Mar 2009 18:59:05 +0000 (11:59 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (10978): Report tuning algorith correctly
V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
V4L/DVB (10974): Use Diseqc 3/3 mode to send data
V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
V4L/DVB (10834): zoran: auto-select bt866 for AverMedia 6 Eyes
V4L/DVB (10832): tvaudio: Avoid breakage with tda9874a
V4L/DVB (10789): m5602-s5k4aa: Split up the initial sensor probe in chunks.
Tyler Hicks [Fri, 13 Mar 2009 20:51:59 +0000 (13:51 -0700)]
eCryptfs: don't encrypt file key with filename key
eCryptfs has file encryption keys (FEK), file encryption key encryption
keys (FEKEK), and filename encryption keys (FNEK). The per-file FEK is
encrypted with one or more FEKEKs and stored in the header of the
encrypted file. I noticed that the FEK is also being encrypted by the
FNEK. This is a problem if a user wants to use a different FNEK than
their FEKEK, as their file contents will still be accessible with the
FNEK.
This is a minimalistic patch which prevents the FNEKs signatures from
being copied to the inode signatures list. Ultimately, it keeps the FEK
from being encrypted with a FNEK.
Johannes Weiner [Fri, 13 Mar 2009 20:51:58 +0000 (13:51 -0700)]
nommu: ramfs: don't leak pages when adding to page cache fails
When a ramfs nommu mapping is expanded, contiguous pages are allocated
and added to the pagecache. The caller's reference is then passed on
by moving whole pagevecs to the file lru list.
If the page cache adding fails, make sure that the error path also
moves the pagevec contents which might still contain up to PAGEVEC_SIZE
successfully added pages, of which we would leak references otherwise.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: David Howells <dhowells@redhat.com> Cc: Enrik Berkhan <Enrik.Berkhan@ge.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enrik Berkhan [Fri, 13 Mar 2009 20:51:56 +0000 (13:51 -0700)]
nommu: ramfs: pages allocated to an inode's pagecache may get wrongly discarded
The pages attached to a ramfs inode's pagecache by truncation from nothing
- as done by SYSV SHM for example - may get discarded under memory
pressure.
The problem is that the pages are not marked dirty. Anything that creates
data in an MMU-based ramfs will cause the pages holding that data will
cause the set_page_dirty() aop to be called.
For the NOMMU-based mmap, set_page_dirty() may be called by write(), but
it won't be called by page-writing faults on writable mmaps, and it isn't
called by ramfs_nommu_expand_for_mapping() when a file is being truncated
from nothing to allocate a contiguous run.
The solution is to mark the pages dirty at the point of allocation by the
truncation code.
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com> Signed-off-by: David Howells <dhowells@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
oopsed, with a BUG_ON in ext4_mb_normalize_request because
size == EXT4_BLOCKS_PER_GROUP
It appears to me (esp. after talking to Andreas) that the BUG_ON
is bogus; a request of exactly EXT4_BLOCKS_PER_GROUP should
be allowed, though larger sizes do indicate a problem.
Fix that an another (apparently rare) codepath with a similar check.
* the 64bit variant now also initializes the padlock unit.
* ->c_early_init() is executed again from ->c_init()
* the 64bit fixups made into 32bit path.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Cc: herbert@gondor.apana.org.au
LKML-Reference: <1237029843-28076-2-git-send-email-sebastian@breakpoint.cc> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adrian Hunter [Mon, 23 Feb 2009 10:47:25 +0000 (12:47 +0200)]
UBIFS: fix bug where page is marked uptodate when out of space
UBIFS fast path in write_begin may mark a page up to date
and then discover that there may not be enough space to do
the write, and so fall back to a slow path. The slow path
tries harder, but may still find no space - leaving the page
marked up to date, when it is not. This patch ensures that
the page is marked not up to date in that case.
The bug that this patch fixes becomes evident when the write
is into a hole (sparse file) or is at the end of the file
and a subsequent read is off the end of the file. In both
cases, the file system should return zeros but was instead
returning the page that had not been written because the
file system was out of space.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Matthew Wilcox [Thu, 12 Mar 2009 18:20:29 +0000 (14:20 -0400)]
[SCSI] sd: Refactor sd_read_capacity()
The sd_read_capacity() function was about 180 lines long and
included a backwards goto and a tricky state variable. Splitting out
read_capacity_10() and read_capacity_16() (about 50 lines each) reduces
sd_read_capacity to about 100 lines and gets rid of the backwards goto
and the state variable. I've tried to avoid any behaviour change with
this patch.
[jejb: upped transfer request to standard recommended 32 for RC16] Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mark Brown [Fri, 13 Mar 2009 14:26:08 +0000 (14:26 +0000)]
ASoC: Fix non-networked I2S mode for PXA SSP
Two issues are fixed here:
- I2S transmits the left frame with the clock low but I don't seem to
get LRCLK out without SFRMDLY being set so invert SFRMP and set a
delay.
- I2S has a clock cycle prior to the first data byte in each channel
so we need to delay the data by one cycle.
Tested-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Vegard Nossum [Sat, 14 Mar 2009 11:08:50 +0000 (12:08 +0100)]
fix regression from "vsprintf: unify the format decoding layer for its 3 users"
Jeremy Fitzhardinge reported:
> Change fef20d9c1380f04ba9492d6463148db07b413708, "vsprintf:
> unify the format decoding layer for its 3 users", causes a
> regression in xenbus which results in no devices getting
> attached to a new domain.
Yinghai Lu [Fri, 13 Mar 2009 19:46:07 +0000 (12:46 -0700)]
x86: fix get_mtrr() warning about smp_processor_id() with CONFIG_PREEMPT=y
Impact: fix debug warning
Jaswinder noticed that there is a warning about smp_processor_id()
in get_mtrr().
Fix it by wrapping the printout into a get/put_cpu() pair.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <49BAB7FF.4030107@kernel.org>
[ changed to get/put_cpu(), cleaned up surrounding code a it. ] Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Sat, 14 Mar 2009 07:46:17 +0000 (08:46 +0100)]
x86: cpu/common.c more cleanups
Complete/fix the cleanups of cpu/common.c:
- fix ugly warning due to asm/topology.h -> linux/topology.h change
- standardize the style across the file
- simplify/refactor the code flow where possible
Lai Jiangshan [Fri, 13 Mar 2009 07:10:26 +0000 (15:10 +0800)]
kallsyms, tracing: output more proper symbol name
Impact: bugfix, output more reliable symbol lookup result
Debug tools(dump_stack(), ftrace...) are like to print out symbols.
But it is always print out the first aliased symbol.(Aliased symbols
are symbols with the same address), and the first aliased symbol is
sometime not proper.
It's very embarrassing, it ouputs "__irqentry_text_start()",
actually, it should output "smp_apic_timer_interrupt()".
(these two symbol are the same address, but "__irqentry_text_start"
is deemed to the first aliased symbol by scripts/kallsyms)
This patch puts symbols like "__irqentry_text_start" to the second
aliased symbols. And a more proper symbol name becomes the first.
Aliased symbols mostly come from linker script. The solution is
guessing "is this symbol defined in linker script", the symbols
defined in linker script will not become the first aliased symbol.
And if symbols are found to be equal in this "linker script provided"
criteria, symbols are sorted by the number of prefix underscores.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Paulo Marques <pmarques@grupopie.com>
LKML-Reference: <49BA06E2.7080807@cn.fujitsu.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
VM, x86, PAT: add a new vm flag to track full pfnmap at mmap
Impact: cleanup
Add a new vm flag VM_PFN_AT_MMAP to identify a PFNMAP that is
fully mapped with remap_pfn_range. Patch removes the overloading
of VM_INSERTPAGE from the earlier patch.
Gabriele Paoloni [Fri, 13 Mar 2009 23:09:12 +0000 (16:09 -0700)]
ppp: ppp_mp_explode() redesign
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.
Problem Description:
As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.
Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).
Problem Solution:
The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g . 10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel). The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: arp announce, arp_proxy and windows ip conflict verification
Windows (XP at least) hosts on boot, with configured static ip, performing
address conflict detection, which is defined in RFC3927.
Here is quote of important information:
"
An ARP announcement is identical to the ARP Probe described above,
except that now the sender and target IP addresses are both set
to the host's newly selected IPv4 address.
"
But it same time this goes wrong with RFC5227.
"
The 'sender IP address' field MUST be set to all zeroes; this is to avoid
polluting ARP caches in other hosts on the same link in the case
where the address turns out to be already in use by another host.
"
When ARP proxy configured, it must not answer to both cases, because
it is address conflict verification in any case. For Windows it is just
causing to detect false "ip conflict". Already there is code for RFC5227, so
just trivially we just check also if source ip == target ip.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: David S. Miller <davem@davemloft.net>
mv643xx_eth: fix unicast address filter corruption on mtu change
When mv643xx_eth_open() is called to up an interface, port_start()
will first re-program the unicast address filter, and then
re-initialise the PORT_CONFIG register, but that will disable unicast
promiscuous mode if it was enabled by the unicast address filter setup.
This isn't a problem on ifconfig up, as ->set_rx_mode() will be called
shortly afterwards which will program the filters again, but it does
trigger when changing the MTU, which calls mv643xx_eth_stop() and then
mv643xx_eth_open() by hand to repopulate the receive rings with skbuffs
of the new size.
Swap the initialisation of the PORT_START register and the call to
the unicast filter setup function to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Lemiech [Fri, 13 Mar 2009 22:43:38 +0000 (15:43 -0700)]
tulip: Fix for MTU problems with 802.1q tagged frames
The original patch was submitted last year but wasn't discussed or applied
because of missing maintainer's CCs. I only fixed some formatting errors,
but as I saw tulip is very badly formatted and needs further work.
Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We
should allow receiving frames of up to 1518 bytes in length, instead of
1514.
Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived
at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.
Tested on D-Link DFE-570TX quad-fastethernet card.
Signed-off-by: Tomasz Lemiech <szpajder@staszic.waw.pl> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Ben McKeegan <ben@netservers.co.uk> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Slusarz [Fri, 13 Mar 2009 22:41:19 +0000 (15:41 -0700)]
phylib: convert state_queue work to delayed_work
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log