sk98lin: kill bogus check and convert to use ARRAY_SIZE()
This converts uses of ARRAY_SIZE(), and while at it also kills
unreachable code as far as I can say. I can't tell what was the author
trying to do with the following check. First we have:
Holger Schurig [Fri, 26 Oct 2007 08:12:14 +0000 (10:12 +0200)]
libertas: move wlan_*_association_work from header to c file
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.
Renamed those two functions to to libertas_XXX as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jes Sorensen [Fri, 26 Oct 2007 14:10:39 +0000 (16:10 +0200)]
iwlwifi: disable interrupts before calling request_irq
Disable interrupts in the iwl4965 before calling request_irq() for
the case that the previous OS or the BIOS left a pending interrupt in
the chip. This behavior has been observed on some laptops such as T61
Thinkpads and Toshiba Portege R500
Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dmitry Torokhov [Fri, 2 Nov 2007 05:55:36 +0000 (01:55 -0400)]
P54: use temporary variables to reduce size of generated code
When there are 2 linked structures, using a temporary variable to hold a pointer
to the often used structure usually produces better code (smaller and faster)
since compiler does not have to constantly re-fetch data from the first structure.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Thu, 11 Oct 2007 03:56:25 +0000 (23:56 -0400)]
orinoco: more reliable scan handling
Bring scan result handling more in line with drivers like ipw. Scan
results are aggregated and a BSS dropped after 15 seconds if no beacon
is received. This allows the driver to interact better with userspace
where more than one process may request scans or results at any time.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 11 Oct 2007 05:05:57 +0000 (00:05 -0500)]
b43legacy: Rewrite pwork locking
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: cleanup Kconfig and ifdefs to split 3945 and 4965
Currently the iwl3945 & iwl4965 drivers share some common Kconfig
symbols. This split it up into options for the individual drivers
and gets rid of all the CONFIG_IWLWIFI cruft.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl3945 and iwl4965 devices share some common structure, but with a
lot of difference split all over. Currently the two drivers share a lot
of headers and use ugly preprocessor magic to manage the difference.
This patch keeps two entirely separate copies of the headers to get rid
of these hacks an ease future development.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mabbas [Thu, 25 Oct 2007 09:15:42 +0000 (17:15 +0800)]
iwl4965: exclude 60M rate from probe request
This patch do the following 2 things:
1. Make sure we don't add rate 60M part of supported rate in proble request,
some AP does not like that.
2. It is wrong to set priv->active_rate in this function, this will set
it to all avialable rates which might overwrite the mode supported rate.
priv->active_rate should be set by only from iwl_set_rate.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:41 +0000 (17:15 +0800)]
iwlwifi: Renames struct fw_image_desc to struct fw_desc
This patche shortens the name of struct fw_image_desc to be struct
fw_desc.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 3945 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves 4965 SCD registers to iwl-prph.h. These registers
are assigned from the periphery bus
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:37 +0000 (17:15 +0800)]
iwlwifi: replacing wording restricted to nic access in iwl-io
This patch replaces wording 'restricted' with more appropriate 'nic access'
NIC access is grabbed to prevent NIC entering power save mode
General cleanup of iwl-io.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mabbas [Thu, 25 Oct 2007 09:15:34 +0000 (17:15 +0800)]
iwlwifi: accept up to 4K frame size on Rx side to fit A-MSDU frame
The driver drops any Rx frame larger than 2332 bytes, but with A-MSDU
frame, it could be up to 4K. This patch makes sure we can process larger
A-MSDU frame.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:32 +0000 (17:15 +0800)]
iwlwifi: using PCI_DEVICE macro
PCI_DEVICE macro is more concise when using defualt values
in device definitions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:31 +0000 (17:15 +0800)]
iwlwifi: remove cck_power_index_compensation
cck_power_index_compensation variable was never used
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ian Schram [Thu, 25 Oct 2007 09:15:30 +0000 (17:15 +0800)]
iwlwifi: remove late null-check and duplicate bug_on
These pieces of code appear to be useless. The BUG_ON is also performed in
iwl_send_cmd_async.
Serious karma would be needed to enter iwl_ativate_qos with a null priv.
I had a deja vu when patching this, but for the life of me I couldn't track
down a similar patch.
Signed-off-by: Ian Schram <ischram@telenet.be> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ian Schram [Thu, 25 Oct 2007 09:15:29 +0000 (17:15 +0800)]
iwlwifi: Beautify by removing superfluous newlines and code
Moving code around, lindent, and whatnot created several places where
there appeared to be an 75 column "rule" instead of 80. This patch removes
those that I can spot, hopefully increasing readability.
Signed-off-by: Ian Schram <ischram@telenet.be> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:27 +0000 (17:15 +0800)]
iwlwifi: remove cck_flag from iwl_driver_hw_info
This patch remove cck_flag from iwl_driver_hw_info, this flag
is unused after spliting the iwl-base.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:26 +0000 (17:15 +0800)]
iwlwifi: add TGN flag to qos parameters
This patch adds TGN flag to QoS parameters. This flag governs enablement of
NAV shortening with CF-End and filters in 4 or 8K RX AMSDU packets
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:25 +0000 (17:15 +0800)]
iwlwifi: rs-4965 fix return values
This patch cleans up style of 'return' of rate scale 4965 functions.
It renames return name variables rc to ret, change functions to void if no
meaningful value was returned it add return of -EINVAL for checks of wrong
arguments.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 25 Oct 2007 09:15:24 +0000 (17:15 +0800)]
iwlwifi: renaming last_used and first_empty
This patch renames queue pointers to write_ptr and read_ptr
instead of first_empty and last_used. This is closer to technical
terminology we everyday use
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 27 Oct 2007 11:44:08 +0000 (13:44 +0200)]
rt2x00: Release rt2x00 2.0.12
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mattias Nissler [Sat, 27 Oct 2007 11:43:49 +0000 (13:43 +0200)]
rt2x00: Correctly set ACK bit in tx descriptors
Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adam Baker [Sat, 27 Oct 2007 11:43:29 +0000 (13:43 +0200)]
rt2x00: Place mutex around USB register access
There is a buffer, csr_cache which is used to hold copies of data being passed
to the USB stack which can get corrupted if multiple threads attempt to access
CSR registers simultaneously. There is also the possibility if multiple
threads try to access BBP or RF registers for the multiple USB operations
needed to get interleaved leading to incorrect results. This patch introduces
a mutex to prevent such simultaneous access. The interleaved access problem
may also affect the PCI devices but if so that will be handled in a follow-up
patch.
Signed-off-by: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Thu, 24 Jan 2008 08:48:03 +0000 (00:48 -0800)]
rt2x00: Remove data_desc structure
Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mattias Nissler [Sat, 27 Oct 2007 11:42:37 +0000 (13:42 +0200)]
rt2x00: Rework rt73 antenna selection
This patch changes rt73 antenna selection to what I believe is the correct way.
It also fixes a small selection bug that switched the antennas by accident.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 27 Oct 2007 11:42:18 +0000 (13:42 +0200)]
rt2x00: Remove unused variables
With the updated antenna setup the following
variables are no longer used.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mattias Nissler [Sat, 27 Oct 2007 11:41:53 +0000 (13:41 +0200)]
rt2x00: Rework rt61 antenna selection.
This patch changes rt61 antenna selection again. It helps at least with the
rt61 pci card in my box, I hope I haven't broken behaviour on other RF chips.
RF 2529 antenna setup is incomplete, we need to at code for diversity when we
figure out how it is done properly.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adam Baker [Sat, 27 Oct 2007 11:41:25 +0000 (13:41 +0200)]
rt2x00: Unconstify rt2x00dev
Some register accesses need rt2x00dev to be non-const
they all need modifying so the prototype is consistent.
Signed-off-by: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 27 Oct 2007 11:40:51 +0000 (13:40 +0200)]
rt2x00: Detect initial rfkill state on register
When registering rfkill, make sure a initial
poll event is directly executed to detect the initial
rfkill state and send the event to the rfkill layer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 27 Oct 2007 11:40:25 +0000 (13:40 +0200)]
rt2x00: Input-polldev requires input device
input-polldev requires a correctly allocated
and initialized input device to be set for the
input_polled_dev->input field.
Failure to do that will prevent correct polling
of the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 27 Oct 2007 11:39:57 +0000 (13:39 +0200)]
rt2x00: Split rt61/rt73 antenna selection into RX and TX antenna
Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
- R77 is the TX antenna configuration
- RF2529 fetches default antenna selection from NIC eeprom word
With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 27 Oct 2007 11:39:28 +0000 (13:39 +0200)]
rt2x00: Disable RX when switching antenna
Antenna switching will be ignored when RX is enabled
during the switch. Make sure we disable the RX during
the switch and don't forget to reenable it later.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:27:16 +0000 (16:27 +0200)]
[PATCH] rt2x00: Release rt2x00 2.0.11
Version bump.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mattias Nissler [Sat, 13 Oct 2007 14:26:57 +0000 (16:26 +0200)]
[PATCH] rt2x00: Fix antenna selection.
In the config() handler, make sure that we do configure an antenna if the
current active antenna is uninitialized. Furthermore, don't overwrite the
active antenna with bogus values if we didn't touch the antenna setup.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:42 +0000 (16:26 +0200)]
[PATCH] rt2x00: Cleanup if-statements
Cleanup if-statements for simple 1/0 register field values.
This also fixes a endian bug in rt2500usb when working
with the PHY_CSR2 initialization. As well as a bug
in the enabling of the LED in rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:36 +0000 (16:26 +0200)]
[PATCH] rt2x00: Implement SW diversity
When mac80211 indicates that the default antenna setup
should be used _and_ that this default setup is SW_DIVERSITY.
This requires sampling and storing the RSSI per antenna
and check once every 2 seconds to determine if the RSSI
has changed significantly. Once this is the case we should sample
the other antenna for a short period and evaluate if
we need to swap antenna or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:32 +0000 (16:26 +0200)]
[PATCH] rt2x00: Remove rt2x00_clear_link
rt2x00_clear_link() was becoming too large for statically inline,
also it was used on a single location and shouldn't really be
used anywhere else. So move the entire code into the function
rt2x00lib_start_link_tuner()
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:27 +0000 (16:26 +0200)]
[PATCH] rt2x00: SW diversity should default to antenna B
Although ANTENNA_SW_DIVERSITY should never be send
to the driver, we should still handle it to prevent bugs.
But instead of defaulting to ANTENNA_HW_DIVERSITY we
should default to ANTENNA_B instead.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:23 +0000 (16:26 +0200)]
[PATCH] rt2x00: Correctly translate mac80211 antenna setup to rt2x00
mac80211 has 3 values for the antenna setup:
0 - default
1 - use antenna 1
2 - use antenna 2
This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.
This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:18 +0000 (16:26 +0200)]
[PATCH] rt2x00: Use enum defines
When setting the default EEPROM values use
the values from the enums instead of "magic" values.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Sat, 13 Oct 2007 14:26:12 +0000 (16:26 +0200)]
[PATCH] rt2x00: Move quality statistics into seperate structure
Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 18 Jan 2008 11:58:07 +0000 (03:58 -0800)]
[NETNS][DST]: Add the network namespace pointer in dst_ops
The network namespace pointer can be stored into the dst_ops structure.
This is usefull when there are multiple instances of the dst_ops for a
protocol. When there are no several instances, this field will be never
used in the protocol. So there is no impact for the protocols which do
implement the network namespaces.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Fri, 18 Jan 2008 11:56:57 +0000 (03:56 -0800)]
[NETNS][DST] dst: pass the dst_ops as parameter to the gc functions
The garbage collection function receive the dst_ops structure as
parameter. This is useful for the next incoming patchset because it
will need the dst_ops (there will be several instances) and the
network namespace pointer (contained in the dst_ops).
The protocols which do not take care of the namespaces will not be
impacted by this change (expect for the function signature), they do
just ignore the parameter.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Jan 2008 11:33:26 +0000 (03:33 -0800)]
[IPV4] FIB_HASH: Reduce memory needs and speedup lookups
Currently, sizeof(struct fib_alias) is 24 or 48 bytes on 32/64 bits
arches.
Because of SLAB_HWCACHE_ALIGN requirement, these are rounded to 32 and
64 bytes respectively.
This patch moves rcu to the end of fib_alias, and conditionally
defines it only for CONFIG_IP_FIB_TRIE.
We also remove SLAB_HWCACHE_ALIGN requirement for fib_alias and
fib_node objects because it is not necessary.
(BTW SLUB currently denies it for objects smaller than
cache_line_size() / 2, but not SLAB)
Finally, sizeof(fib_alias) go back to 16 and 32 bytes.
Then, we can embed one fib_alias on each fib_node, to favor locality.
Most of the time access to the fib_alias will be free because one
cache line contains both the list head (fn_alias) and (one of) the
list element.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Jan 2008 11:31:36 +0000 (03:31 -0800)]
[FIB]: Fix rcu_dereference() abuses in fib_trie.c
node_parent() and tnode_get_child() currently use rcu_dereference().
These functions are called from both
- readers only paths (where rcu_dereference() is needed), and
- writer path (where rcu_dereference() is not needed)
To make explicit where rcu_dereference() is really needed, I
introduced new node_parent_rcu() and tnode_get_child_rcu() functions
which use rcu_dereference(), while node_parent() and tnode_get_child()
dont use it.
Then I changed calling sites where rcu_dereference() was really needed
to call the _rcu() variants.
This should have no impact but for alpha architecture, and may help
future sparse checks.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jan 2008 07:48:57 +0000 (23:48 -0800)]
[NETFILTER]: nf_conntrack: clean up a few header files
- Remove declarations of non-existing variables and functions
- Move helper init/cleanup function declarations to nf_conntrack_helper.h
- Remove unneeded __nf_conntrack_attach declaration and make it static
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jan 2008 07:48:39 +0000 (23:48 -0800)]
[NETFILTER]: kill nf_sysctl.c
Since there now is generic support for shared sysctl paths, the only
remains are the net/netfilter and net/ipv4/netfilter paths. Move them
to net/netfilter/core.c and net/ipv4/netfilter.c and kill nf_sysctl.c.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jan 2008 07:45:48 +0000 (23:45 -0800)]
[NETFILTER]: nf_conntrack_sctp: basic cleanups
Reindent switch cases properly, get rid of weird constructs like "!(x == y)",
put logical operations on the end of the line instead of the next line, get
rid of superfluous braces.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jan 2008 07:45:11 +0000 (23:45 -0800)]
[NETFILTER]: nf_conntrack_{tcp,sctp}: shrink state table
The TCP and SCTP conntrack state transition tables only holds
small numbers, but gcc uses 4 byte per entry for the enum. Switching
to an u8 reduces the size from 480 to 120 bytes for TCP and from
576 to 144 bytes for SCTP.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Denys Vlasenko [Tue, 15 Jan 2008 07:44:26 +0000 (23:44 -0800)]
[NETFILTER]: ipt_REJECT: properly handle IP options
The current TCP RST construction reuses the old packet and can't
deal with IP options as a consequence of that. Construct the
RST from scratch instead.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Denys Vlasenko [Tue, 15 Jan 2008 07:44:05 +0000 (23:44 -0800)]
[NETFILTER]: {ip,ip6}_tables: remove some inlines
This patch removes inlines except those which are used
by packet matching code and thus are performance-critical.
Before:
$ size */*/*/ip*tables*.o
text data bss dec hex filename
6402 500 16 6918 1b06 net/ipv4/netfilter/ip_tables.o
7130 500 16 7646 1dde net/ipv6/netfilter/ip6_tables.o
After:
$ size */*/*/ip*tables*.o
text data bss dec hex filename
6307 500 16 6823 1aa7 net/ipv4/netfilter/ip_tables.o
7010 500 16 7526 1d66 net/ipv6/netfilter/ip6_tables.o
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 15 Jan 2008 07:43:34 +0000 (23:43 -0800)]
[NETFILTER]: Update feature-removal-schedule.txt
With all the newly introduced features, there is a lot to remove
later on after a compatibility grace period of 2 years.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 15 Jan 2008 07:43:03 +0000 (23:43 -0800)]
[NETFILTER]: xt_iprange match, revision 1
Adds IPv6 support to xt_iprange, making it possible to match on IPv6
address ranges with ip6tables.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 15 Jan 2008 07:42:47 +0000 (23:42 -0800)]
[NETFILTER]: Rename ipt_iprange to xt_iprange
This patch moves ipt_iprange to xt_iprange, in preparation for adding
IPv6 support to xt_iprange.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 15 Jan 2008 07:42:28 +0000 (23:42 -0800)]
[NETFILTER]: Update modules' descriptions
Updates the MODULE_DESCRIPTION() tags for all Netfilter modules,
actually describing what the module does and not just
"netfilter XYZ target".
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Tue, 15 Jan 2008 07:42:06 +0000 (23:42 -0800)]
[NETFILTER]: xt_policy: use the new union nf_inet_addr
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log