ide-cd: convert ide_cd_queue_pc to use blk_execute_rq
This converts ide_cd_queue_pc to use blk_execute_rq, necessitating
changing the ide_cd_queue_pc prototype into a form that doesn't takes
a pointer to request struct. ide_cd_queue_pc works like scsi_execute.
ide: use __generic_unplug_device() in ide_do_drive_cmd() (take 2)
* Call __elv_add_request() with 'plug' == 1 (so the device will be
plugged) and then use __generic_unplug_device() instead of calling
ide_do_request() directly.
v2:
* For blk_pm_resume_request() requests the queue is stopped so we
need to call ->request_fn explicitly.
Thanks to:
- Rafael for reporting/bisecting the bug
- Borislav/Rafael for testing the fix
This is a preparation for converting IDE to use blk_execute_rq().
ide: disable drive interrupts in ide_driveid_update()
Since ide_driveid_update() uses polling to execute the IDENTIFY DEVICE command
but clears nIEN bit in the control register and doesn't mask the IDE interrupt,
the latter does happen and lead to the corresponding message to appear:
ide0: unexpected interrupt, status=0x58, count=1
when e.g. running hdparm with option -X with a non-PCI IDE driver...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
jfs: remove DIRENTSIZ
JFS: diAlloc() should return -EIO rather than EIO
JFS: skip bad iput() call in error path
JFS: switch to seq_files
JFS: 0 is not valid errno value so return NULL from jfs_lookup
Split out PCIC dependent code and SoC dependent code from board dependent
code. Now TX4927 PCIC code is independent from TX4927/TX4938 SoC code.
Also fix some build problems on CONFIG_PCI=n.
As a bonus, "FPCIB0 Backplane Support" is available for all TX39/TX49 boards
and PCI66 support is available for all TX49 boards.
[MIPS] txx9: Make gpio_txx9 entirely spinlock-safe
TXx9 GPIO set/get routines are spinlock-safe. This patch make
gpio_direction_{input,output} routines also spinlock-safe so that they
can be used during early board setup.
-ffunction-sections serves as a workaround for the problems caused by the
limited branch range in some inline assembler fragments for very large
compilation units.
[MIPS] IP28: switch to "normal" mode after PROM no longer needed
SGI-IP28 is running in so called slow mode, when kernel is started
from the PROM. PROM calls must be done in slow mode otherwise the
PROM will issue an error. To get better memory performance we now
switch to normal mode, when the PROM is no longer needed.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dmitri Vorobiev [Wed, 18 Jun 2008 07:18:23 +0000 (10:18 +0300)]
[MIPS] Add an appropriate header into display.c
The following errors were caught by sparse:
>>>>>>>>>>>
arch/mips/mips-boards/generic/display.c:30:6: warning: symbol
'mips_display_message' was not declared. Should it be static?
arch/mips/mips-boards/generic/display.c:58:6: warning: symbol
'mips_scroll_message' was not declared. Should it be static?
>>>>>>>>>>>
This patch includes the asm/mips-boards/prom.h header file into
arch/mips/mips-boards/generic/display.c. This adds the needed
function declarations, and the errors are gone.
Compile-tested using defconfigs for Malta, Atlas and SEAD boards.
Runtime test was successfully performed by booting a Malta 4Kc
board up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dmitri Vorobiev [Wed, 18 Jun 2008 07:18:21 +0000 (10:18 +0300)]
[MIPS] A few cleanups in malta_int.c
Both the fill_ipi_map() routine and the gic_intr_map array defined
in arch/mips/mips-boards/malta/malta_int.c are not used outside of
the latter file. Thus, these objects can become static. Moreover,
these two objects are used by the MT code only, which is why this
patch adds the appropriate ifdef.
While at it, this patch removes an unnecessary preprocessing macro
in favor of the commonly used ARRAY_SIZE.
Successfully tested using a Qemu-emulated Malta board for both SMP
and UP kernels.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both onboard controller of the O2 support FAST-20 transfer speeds,
but the bit, which signals that to the aic driver, isn't set. Instead
of adding detection code to the scsi driver, we just fake the missing
bit in the PCI config space of the scsi chips.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
because gcc was not able to figure out that the "i" constraint was possibly
at the early stage when the constraint are getting verified. The solution
was using "ri" instead of "i". The "ri" would keep gcc happy but in the
end for code generation always the "i" constraint would be satisfied. The
problem afair originally appeared in the i386 io.h and also hit it's mips
equivalent. From there the workaround spread to many of the inline
assembler functions.]
Signed-off-by: David Daney <ddaney@avtrex.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[MIPS] DECstation: Document more MB ASIC register bits
Document a few more register bits provided by the MB ASIC used on R4000SC
(KN04) and R4400SC (KN05) CPU daughtercards with the DECstation.
Reverse-engineered and not documented anywhere else to the best of my
knowledge. Bit names appended to the last underscore the same as reported
by the firmware in register dumps.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dmitri Vorobiev [Thu, 29 May 2008 14:57:09 +0000 (17:57 +0300)]
[MIPS] Make two functions static
The following routines
uasm_rel_highest()
uasm_rel_higher()
are needlessly defined global. This patch makes them static.
Compile-tested using a customized config for the Malta board. Booting
the same board up to the shell prompt was also successful with this
patch applied.
Spotted by sparse.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The isa_slot_offset variable and its __ISA_IO_base macro is not used
anywhere anymore. It does not look like a decent interface per today's
standards either. Remove both including all places of initialization.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge branch 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add PCI ID for 6300ESB force hpet
x86: add another PCI ID for ICH6 force-hpet
kernel-paramaters: document pmtmr= command line option
acpi_pm clccksource: fix printk format warning
nohz: don't stop idle tick if softirqs are pending.
pmtmr: allow command line override of ioport
nohz: reduce jiffies polling overhead
hrtimer: Remove unused variables in ktime_divns()
hrtimer: remove warning in hres_timers_resume
posix-timers: print RT watchdog message
Rabin Vincent [Thu, 3 Jul 2008 19:10:32 +0000 (00:40 +0530)]
slab: rename slab_destroy_objs
With the removal of destructors, slab_destroy_objs no longer actually
destroys any objects, making the kernel doc incorrect and the function
name misleading.
In keeping with the other debug functions, rename it to
slab_destroy_debugcheck and drop the kernel doc.
Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
We can detect kfree()s on non slab objects by checking for PageCompound().
Works in the same way as for ksize. This helped me catch an invalid
kfree().
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Merge branch 'core/topology' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/topology' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cputopology: always define CPU topology information, clean up
cpu topology: always define CPU topology information
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix compile error with CONFIG_AS_CFI=n
Documentation: document debugpat commandline option
x86: sanitize Kconfig
x86, suspend, acpi: correct and add comments about Big Real Mode
x86, suspend, acpi: enter Big Real Mode
Fixed trivial conflict in include/asm-x86/dwarf2.h due to just using
different names for "cfi_ignore" (vs "__cfi_ignore") macro.
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (61 commits)
ext4: Documention update for new ordered mode and delayed allocation
ext4: do not set extents feature from the kernel
ext4: Don't allow nonextenst mount option for large filesystem
ext4: Enable delalloc by default.
ext4: delayed allocation i_blocks fix for stat
ext4: fix delalloc i_disksize early update issue
ext4: Handle page without buffers in ext4_*_writepage()
ext4: Add ordered mode support for delalloc
ext4: Invert lock ordering of page_lock and transaction start in delalloc
mm: Add range_cont mode for writeback
ext4: delayed allocation ENOSPC handling
percpu_counter: new function percpu_counter_sum_and_set
ext4: Add delayed allocation support in data=writeback mode
vfs: add hooks for ext4's delayed allocation support
jbd2: Remove data=ordered mode support using jbd buffer heads
ext4: Use new framework for data=ordered mode in JBD2
jbd2: Implement data=ordered mode handling via inodes
vfs: export filemap_fdatawrite_range()
ext4: Fix lock inversion in ext4_ext_truncate()
ext4: Invert the locking order of page_lock and transaction start
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
Revert "SELinux: allow fstype unknown to policy to use xattrs if present"
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/mlx4: Use kzalloc() for new QPs so flags are initialized to 0
mlx4_core: Use MOD_STAT_CFG command to get minimal page size
RDMA/cma: Simplify locking needed for serialization of callbacks
RDMA/addr: Keep pointer to netdevice in struct rdma_dev_addr
RDMA/cxgb3: Fixes for zero STag
RDMA/core: Add local DMA L_Key support
IB/mthca: Fix check of max_send_sge for special QPs
IB/mthca: Use round_jiffies() for catastrophic error polling timer
IB/mthca: Remove "stop" flag for catastrophic error polling timer
IPoIB: Double default RX/TX ring sizes
IPoIB/cm: Reduce connected mode TX object size
IB/ipath: Use IEEE OUI for vendor_id reported by ibv_query_device()
IPoIB: Use dev_set_mtu() to change mtu
IPoIB: Use rtnl lock/unlock when changing device flags
IPoIB: Get rid of ipoib_mcast_detach() wrapper
IPoIB: Only set Q_Key once: after joining broadcast group
IPoIB: Remove priv->mcast_mutex
IPoIB: Remove unused IPOIB_MCAST_STARTED code
RDMA/cxgb3: Set rkey field for new memory windows in iwch_alloc_mw()
RDMA/nes: Get rid of ring_doorbell parameter of nes_post_cqp_request()
...
Kevin Winchester [Tue, 15 Jul 2008 00:36:13 +0000 (21:36 -0300)]
x86: Fix compile error with CONFIG_AS_CFI=n
AS arch/x86/lib/csum-copy_64.o
arch/x86/lib/csum-copy_64.S: Assembler messages:
arch/x86/lib/csum-copy_64.S:48: Error: Macro `ignore' was already defined
make[1]: *** [arch/x86/lib/csum-copy_64.o] Error 1
make: *** [arch/x86/lib] Error 2
It appears that csum-copy_64.S and dwarf2.h both define an ignore macro.
I would expect one of them can be renamed quite easily, unless they
are references elsewhere.
Eli Cohen [Tue, 15 Jul 2008 06:48:53 +0000 (23:48 -0700)]
IB/mlx4: Use kzalloc() for new QPs so flags are initialized to 0
Current code uses kmalloc() and then just does a bitwise OR operation on
qp->flags in create_qp_common(), which means that qp->flags may
potentially have some unintended bits set. This patch uses kzalloc()
and avoids further explicit clearing of structure members, which also
shrinks the code:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-65 (-65)
function old new delta
create_qp_common 2024 1959 -65
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_core: Use MOD_STAT_CFG command to get minimal page size
There was a bug in some versions of the mlx4 driver in
mlx4_alloc_fmr(), which hardcoded the minimum acceptable page_shift to
be 12. However, new ConnectX firmware can support a minimum
page_shift of 9 (log_pg_sz of 9 returned by QUERY_DEV_LIM) -- so with
old drivers, ib_fmr_alloc() would fail for ULPs using the device
minimum when creating FMRs.
To preserve firmware compatibility with released mlx4 drivers, the
firmware will continue to return 12 as before for log_page_sz in
QUERY_DEV_CAP for these drivers. However, to enable new drivers to
take advantage of the available smaller page size, the mlx4 driver now
first sets the log_pg_sz to the device minimum by setting a
log_page_sz value to 0 via the MOD_STAT_CFG command and then reading
the real minimum via QUERY_DEV_CAP.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il> Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz [Tue, 15 Jul 2008 06:48:53 +0000 (23:48 -0700)]
RDMA/cma: Simplify locking needed for serialization of callbacks
The RDMA CM has some logic in place to make sure that callbacks on a
given CM ID are delivered to the consumer in a serialized manner.
Specifically it has code to protect against a device removal racing
with a running callback function.
This patch simplifies this logic by using a mutex per ID instead of a
wait queue and atomic variable. This means that cma_disable_remove()
now is more properly named to cma_disable_callback(), and
cma_enable_remove() can now be removed because it just would become a
trivial wrapper around mutex_unlock().
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz [Tue, 15 Jul 2008 06:48:53 +0000 (23:48 -0700)]
RDMA/addr: Keep pointer to netdevice in struct rdma_dev_addr
Keep a pointer to the local (src) netdevice in struct rdma_dev_addr,
and copy it in as part of rdma_copy_addr(). Use rdma_translate_ip()
in cma_new_conn_id() to reduce some code duplication and also make
sure the src_dev member gets set.
In a high-availability configuration the netdevice pointer can be used
by the RDMA CM to align RDMA sessions to use the same links as the IP
stack does under fail-over and route change cases.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Steve Wise [Tue, 15 Jul 2008 06:48:53 +0000 (23:48 -0700)]
RDMA/cxgb3: Fixes for zero STag
Handling the zero STag in receive work request requires some extra
logic in the driver:
- Only set the QP_PRIV bit for kernel mode QPs.
- Add a zero STag build function for recv wrs. The uP needs a PBL
allocated and passed down in the recv WR so it can construct a HW
PBL for the zero STag S/G entries. Note: we need to place a few
restrictions on zero STag usage because of this:
1) all SGEs in a recv WR must either be zero STag or not. No mixing.
2) an individual SGE length cannot exceed 128MB for a zero-stag SGE.
This should be OK since it's not really practical to allocate
such a large chunk of pinned contiguous DMA mapped memory.
- Add an optimized non-zero-STag recv wr format for kernel users.
This is needed to optimize both zero and non-zero STag cracking in
the recv path for kernel users.
- Remove the iwch_ prefix from the static build functions.
- Bump required FW version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Steve Wise [Tue, 15 Jul 2008 06:48:53 +0000 (23:48 -0700)]
RDMA/core: Add local DMA L_Key support
- Change the IB_DEVICE_ZERO_STAG flag to the transport-neutral name
IB_DEVICE_LOCAL_DMA_LKEY, which is used by iWARP RNICs to indicate 0
STag support and IB HCAs to indicate reserved L_Key support.
- Add a u32 local_dma_lkey member to struct ib_device. Drivers fill
this in with the appropriate local DMA L_Key (if they support it).
- Fix up the drivers using this flag.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Tue, 15 Jul 2008 06:48:52 +0000 (23:48 -0700)]
IB/mthca: Fix check of max_send_sge for special QPs
The MLX transport requires two extra gather entries for sends (one for
the header and one for the checksum at the end, as the comment says).
However the code checked that max_recv_sge was not too big, instead of
checking max_send_sge as it should have. Fix the code to check the
correct condition.
Eli Cohen [Tue, 15 Jul 2008 06:48:52 +0000 (23:48 -0700)]
IPoIB: Double default RX/TX ring sizes
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks. With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput. Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Tue, 15 Jul 2008 06:48:52 +0000 (23:48 -0700)]
IPoIB/cm: Reduce connected mode TX object size
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array. Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell [Tue, 15 Jul 2008 06:48:52 +0000 (23:48 -0700)]
IB/ipath: Use IEEE OUI for vendor_id reported by ibv_query_device()
The IB spe. for SubnGet(NodeInfo) and query HCA says that the vendor
ID field should be the IEEE OUI assigned to the vendor. The ipath
driver was returning the PCI vendor ID instead. This will affect
applications which call ibv_query_device(). The old value was
0x001fc1 or 0x001077, the new value is 0x001175.
The vendor ID doesn't appear to be exported via /sys so that should
reduce possible compatibility issues. I'm only aware of Open MPI as a
major application which depends on this change, and they have made
necessary adjustments.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Tue, 15 Jul 2008 06:48:51 +0000 (23:48 -0700)]
IPoIB: Use dev_set_mtu() to change mtu
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice. Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Tue, 15 Jul 2008 06:48:51 +0000 (23:48 -0700)]
IPoIB: Use rtnl lock/unlock when changing device flags
Use of this lock is required to synchronize changes to the netdvice's
data structs. Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
projects / linux-2.6-omap-h63xx.git / log