If a mesh or ad-hoc interface is brought up and later it is replaced
by managed interface, the managed interface will keep transmitting
the beacons that were configured for the former interface. This patch
fixes that behaviour.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 8 Jul 2008 11:45:20 +0000 (13:45 +0200)]
rt2x00: Disable synchronization during initialization
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the fast_start parameter from the rc_pid parameters
information and instead uses the parameter macro when initializing
the rc_pid state. Since the parameter is only used on initialization,
there is no point of making exporting it via debugfs. This also fixes
uninitialized memory references to the fast_start and norm_offset
parameters detected by the kmemcheck utility. Thanks to Vegard Nossum
for reporting the bug.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefan Roese [Wed, 9 Jul 2008 15:09:23 +0000 (01:09 +1000)]
powerpc: Fix problems with 32bit PPC's running with >= 4GB of RAM
This patch enables 32bit PPC's (with 36bit physical address space, e.g.
IBM/AMCC PPC44x) to run with >= 4GB of RAM. Mostly its just replacing types
(unsigned long -> phys_addr_t).
Tested on an AMCC Katmai with 4GB of DDR2.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is some preliminary work to improve TLB management on SW loaded
TLB powerpc platforms. This introduce support for non-atomic PTE
operations in pgtable-ppc32.h and removes write back to the PTE from
the TLB miss handlers. In addition, the DSI interrupt code no longer
tries to fixup write permission, this is left to generic code, and
_PAGE_HWWRITE is gone.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Grant Likely [Wed, 9 Jul 2008 15:41:52 +0000 (09:41 -0600)]
powerpc/bootwrapper: Allow user to specify additional default targets
It is inconvenient to add additional default targets to the bootwrapper
Makefile for each new board supported which just needs a different dts
file. This change allows the defconfig to specify additional build
targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Mike Mason [Tue, 8 Jul 2008 16:04:35 +0000 (02:04 +1000)]
powerpc/eeh: PERR/SERR bit settings during EEH device recovery
The following patch restores the PERR and SERR bits in the PCI
command register during an EEH device recovery. We have found
at least one case (an Agilent test card) where the PERR/SERR
bits are set to 1 by firmware at boot time, but are not restored
to 1 during EEH recovery. The patch fixes the Agilent card
problem. It has been tested on several other EEH-enabled cards
with no regressions.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com> Acked-by: Linas Vepstas <linasvepstas@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Tue, 8 Jul 2008 08:43:41 +0000 (18:43 +1000)]
powerpc: fix swapcontext backwards compat. with VSX ucontext changes
When the ucontext changed to add the VSX context, this broke backwards
compatibly on swapcontext. swapcontext only compares the ucontext size
passed in from the user to the new kernel ucontext size.
This adds a check against the old ucontext size (with VMX but without
VSX). It also adds some sanity check for ucontexts without VSX, but
where VSX is used according the MSR. Fixes for both 32 and 64bit
processes on 64bit kernels
Kudos to Paulus for noticing.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Grant Erickson [Mon, 7 Jul 2008 22:03:11 +0000 (08:03 +1000)]
ibm_newemac: Parameterize EMAC Multicast Match Handling
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.
As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.
The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.
This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.
The code has further been reworked where appropriate to use those macros
and inlines.
In addition, the register size passed to ioremap is now taken from the
device tree:
c4 for EMAC4SYNC cores
74 for EMAC4 cores
70 for EMAC cores
rather than sizeof (emac_regs).
Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.
This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Mon, 7 Jul 2008 14:28:55 +0000 (00:28 +1000)]
powerpc/mm: Don't clear _PAGE_COHERENT when _PAGE_SAO is set
The current low level hash code on LPAR configurations clears
_PAGE_COHERENT (M) when either _PAGE_GUARDED (G) or _PAGE_NO_CACHE (I)
is set. This conflicts with _PAGE_SAO which has M, I and W bits sets at
once (normally invalid combo) to indicate the new SAO attribute.
This changes the code to allow that case.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Mon, 7 Jul 2008 14:28:54 +0000 (00:28 +1000)]
powerpc/mm: Add Strong Access Ordering support
Allow an application to enable Strong Access Ordering on specific pages of
memory on Power 7 hardware. Currently, power has a weaker memory model than
x86. Implementing a stronger memory model allows an emulator to more
efficiently translate x86 code into power code, resulting in faster code
execution.
On Power 7 hardware, storing 0b1110 in the WIMG bits of the hpte enables
strong access ordering mode for the memory page. This patchset allows a
user to specify which pages are thus enabled by passing a new protection
bit through mmap() and mprotect(). I have defined PROT_SAO to be 0x10.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Mon, 7 Jul 2008 14:28:53 +0000 (00:28 +1000)]
powerpc/mm: Add SAO Feature bit to the cputable
Add the CPU feature bit for the new Strong Access Ordering
facility of Power7
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Mon, 7 Jul 2008 14:28:52 +0000 (00:28 +1000)]
powerpc/mm: Define flags for Strong Access Ordering
This patch defines:
- PROT_SAO, which is passed into mmap() and mprotect() in the prot field
- VM_SAO in vma->vm_flags, and
- _PAGE_SAO, the combination of WIMG bits in the pte that enables strong
access ordering for the page.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dave Kleikamp [Mon, 7 Jul 2008 14:28:51 +0000 (00:28 +1000)]
mm: Allow architectures to define additional protection bits
This patch allows architectures to define functions to deal with
additional protections bits for mmap() and mprotect().
arch_calc_vm_prot_bits() maps additonal protection bits to vm_flags
arch_vm_get_page_prot() maps additional vm_flags to the vma's vm_page_prot
arch_validate_prot() checks for valid values of the protection bits
Note: vm_get_page_prot() is now pretty ugly, but the generated code
should be identical for architectures that don't define additional
protection bits.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Acked-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark Nelson [Fri, 4 Jul 2008 19:05:45 +0000 (05:05 +1000)]
powerpc: move device_to_mask() to dma-mapping.h
Move device_to_mask() to dma-mapping.h because we need to use it from
outside dma_64.c in a later patch.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark Nelson [Fri, 4 Jul 2008 19:05:44 +0000 (05:05 +1000)]
powerpc/cell: cell_dma_dev_setup_iommu() return the iommu table
Make cell_dma_dev_setup_iommu() return a pointer to the struct iommu_table
(or NULL if no table can be found) rather than putting this pointer into
dev->archdata.dma_data (let the caller do that), and rename this function
to cell_get_iommu_table() to reflect this change.
This will allow us to get the iommu table for a device that doesn't have
the table in the archdata.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark Nelson [Fri, 4 Jul 2008 19:05:42 +0000 (05:05 +1000)]
powerpc/dma: implement new dma_*map*_attrs() interfaces
Update powerpc to use the new dma_*map*_attrs() interfaces. In doing so
update struct dma_mapping_ops to accept a struct dma_attrs and propagate
these changes through to all users of the code (generic IOMMU and the
64bit DMA code, and the iseries and ps3 platform code).
The old dma_*map_*() interfaces are reimplemented as calls to the
corresponding new interfaces.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark Nelson [Fri, 4 Jul 2008 19:05:41 +0000 (05:05 +1000)]
powerpc/dma: Add struct iommu_table argument to iommu_map_sg()
Make iommu_map_sg take a struct iommu_table. It did so before commit 740c3ce66700640a6e6136ff679b067e92125794 (iommu sg merging: ppc: make
iommu respect the segment size limits).
This stops the function looking in the archdata.dma_data for the iommu
table because in the future it will be called with a device that has
no table there.
This also has the nice side effect of making iommu_map_sg() match the
other map functions.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/spufs: add atomic busy_spus counter to struct cbe_spu_info
As nr_active counter includes also spus waiting for syscalls to return
we need a seperate counter that only counts spus that are currently running
on spu side. This counter shall be used by a cpufreq governor that targets
a frequency dependent from the number of running spus.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Add missing reference to coherent_dma_mask
There is dma_mask in of_device upon of_platform_device_create()
but we don't actually set coherent_dma_mask. This may cause weird
behavior of USB subsystem using of_device USB host drivers.
Jeremy Kerr [Thu, 3 Jul 2008 01:42:20 +0000 (11:42 +1000)]
powerpc/spufs: only add ".ctx" file with "debug" mount option
Currently, the .ctx debug file in spu context directories is always
present.
We'd prefer to prevent users from relying on this file, so add a
"debug" mount option to spufs. The .ctx file will only be added to
the context directories when this option is present.
Jeremy Kerr [Mon, 30 Jun 2008 04:38:37 +0000 (14:38 +1000)]
powerpc/spufs: add sizes for context files
Populate the size member of a few context files. Leave out files that
have different semantics with read vs mmap, or contain a
variable-length hex string.
Jeremy Kerr [Mon, 30 Jun 2008 02:17:28 +0000 (12:17 +1000)]
powerpc/spufs: allow spufs files to specify sizes
Currently, spufs never specifies the i_size for the files in context
directories, so stat() always reports 0-byte files.
This change adds allows the spufs_dir_(nosched_)contents arrays to
specify a file size. This allows stat() to report correct file sizes,
and makes SEEK_END work.
Luke Browning [Fri, 6 Jun 2008 03:26:54 +0000 (11:26 +0800)]
powerpc/spufs: don't extend time time slice if context is not in spu_run
An spu context shouldn't get an extra tick if the time slice code
couldn't find something else to run. This means contexts that are not
within spu_run (ie, SPU_SCHED_SPU_RUN is cleared) will not receive
extra ticks while we have no other contexts waiting.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Luke Browning [Mon, 16 Jun 2008 01:36:43 +0000 (11:36 +1000)]
powerpc/spufs: provide context debug file
Add a ctxt file to spufs that shows spu context information that is used
in scheduling. This info can be used for debugging spufs scheduler
issues, and to isolate between application and spufs problems as it
shows a lot of state such as priorities and dispatch counts.
This file contains internal spufs state and is subject to change at any
time, and therefore no applications should depend on it. The file is
intended for the use of spufs kernel developers.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After this we have an ifp->rt inserted into fib6 lists, but
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught
only the oops in gc so far.
The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Wise [Tue, 8 Jul 2008 21:40:05 +0000 (14:40 -0700)]
RDMA/cxgb3: Fix regression caused by class_device -> device conversion
The change to iwch_provider.c in commit f4e91eb4 ("IB: convert struct
class_device to struct device") undid the fix done in commit 7f049f2f
("RDMA/cxgb3: Hold rtnl_lock() around ethtool get_drvinfo call"). It
removed the calls to rtnl_lock() that serialized the iw_cxgb3 ethtool
ops calls into the cxgb3 driver. This locking is needed to avoid
messing up the internal state of the cxgb3 driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Merge branch 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix an rpcbind breakage for the case of IPv6 lookups
SUNRPC: Fix a double-free in rpcbind
NFS: Fix readdir cache invalidation
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix 32bit kernels on R4k with 128 byte cache line size
[MIPS] Atlas, decstation: Fix section mismatches triggered by defconfigs
Jeff Mahoney [Tue, 8 Jul 2008 18:37:06 +0000 (14:37 -0400)]
reiserfs: discard prealloc in reiserfs_delete_inode
With the removal of struct file from the xattr code,
reiserfs_file_release() isn't used anymore, so the prealloc isn't
discarded. This causes hangs later down the line.
This patch adds it to reiserfs_delete_inode. In most cases it will be a
no-op due to it already having been called, but will avoid hangs with
xattrs.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SUNRPC: Fix an rpcbind breakage for the case of IPv6 lookups
Now that rpcb_next_version has been split into an IPv4 version and an IPv6
version, we Oops when rpcb_call_async attempts to look up the IPv6-specific
RPC procedure in rpcb_next_version.
Fix the Oops simply by having rpcb_getport_async pass the correct RPC
procedure as an argument.
It is wrong to be freeing up the rpcbind arguments if the call to
rpcb_call_async() fails, since they should already have been freed up by
rpcb_map_release().
invalidate_inode_pages2_range() takes page offset arguments, not byte
ranges.
Another thought is that individual pages might perhaps get evicted by VM
pressure, in which case we might perhaps want to re-read not only the
evicted page, but all subsequent pages too (in case the server returns
more/less data per page so that the alignment of the next entry
changes). We should therefore remove the condition that we only do this on
page->index==0.
[MIPS] Fix 32bit kernels on R4k with 128 byte cache line size
The generated copy_page for R4k CPU with a 128 byte cache line size used
Create Dirty Exclusive cache line operations even if only part of the
cache line was filled. This change avoids generating cache operations,
if only part of the cache line size is copied in one loop. It also
increases the maxmimum loop size, because the generated code even fits
into the available space for r4k CPUs with 128 byte cache line size.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sergei Shtylyov [Tue, 8 Jul 2008 17:27:22 +0000 (19:27 +0200)]
palm_bk3710: fix IDECLK period calculation
The driver uses completely bogus rounding formula for calculating period from
the IDECLK frequency which gives one-off period values (e.g. 11 ns with 100 MHz
IDECLK) which in turn can lead to overclocked IDE transfer timings. Actually,
rounding is just wrong in this case, so use a mere division for a safe result.
While at it, also:
- give 'ide_palm_clk' variable a more suitable name;
- get rid of the useless 'ideclkp' variable;
- drop the LISP stype 'p' postfix from the 'clkp' variable's name. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: mcherkashin@ru.mvista.com Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add __ide_default_irq() inline helper and use it instead of
ide_default_irq() in ide-probe.c and ns87415.c (all host drivers
except IDE PCI ones always setup hwif->irq so it is enough to
check only for I/O bases 0x1f0 and 0x170).
This fixes post-2.6.25 regression since ide_default_irq()
define could shadow ide_default_irq() inline.
David Gibson [Tue, 8 Jul 2008 05:58:16 +0000 (15:58 +1000)]
Correct hash flushing from huge_ptep_set_wrprotect()
As Andy Whitcroft recently pointed out, the current powerpc version of
huge_ptep_set_wrprotect() has a bug. It just calls ptep_set_wrprotect()
which in turn calls pte_update() then hpte_need_flush() with the 'huge'
argument set to 0. This will cause hpte_need_flush() to flush the wrong
hash entries (of any). Andy's fix for this is already in the powerpc
tree as commit 016b33c4958681c24056abed8ec95844a0da80a3.
I have confirmed this is a real bug, not masked by some other
synchronization, with a new testcase for libhugetlbfs. A process write
a (MAP_PRIVATE) hugepage mapping, fork(), then alter the mapping and
have the child incorrectly see the second write.
Therefore, this should be fixed for 2.6.26, and for the stable tree.
Here is a suitable patch for 2.6.26, which I think will also be suitable
for the stable tree (neither of the headers in question has been changed
much recently).
It is cut down slighlty from Andy's original version, in that it does
not include a 32-bit version of huge_ptep_set_wrprotect(). Currently,
hugepages are not supported on any 32-bit powerpc platform. When they
are, a suitable 32-bit version can be added - the only 32-bit hardware
which supports hugepages does not use the conventional hashtable MMU and
so will have different needs anyway.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Mon, 7 Jul 2008 16:24:06 +0000 (11:24 -0500)]
[SCSI] mptspi: fix oops in mptspi_dv_renegotiate_work()
The problem here is that if the ioc faults too early in the bring up
sequence (as it usually does for an irq routing problem), ioc_reset gets
called before the scsi host is even allocated. This causes an oops when
it later schedules a renegotiation. Fix this by checking ioc->sh before
trying to renegotiate.
Cc: "Moore, Eric" <Eric.Moore@lsi.com> Cc: Stable Tree <stable@kernel.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Julius Volz [Tue, 8 Jul 2008 10:07:43 +0000 (03:07 -0700)]
irda: Fix netlink error path return value
Fix an incorrect return value check of genlmsg_put() in irda_nl_get_mode().
genlmsg_put() does not use ERR_PTR() to encode return values, it just
returns NULL on error.
Signed-off-by: Julius Volz <juliusv@google.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ville Syrjala [Tue, 8 Jul 2008 10:07:16 +0000 (03:07 -0700)]
irda: New device ID for nsc-ircc
HP OmniBook 500's DSDT code changes the HID of the FIR device from
NSC6001 to HWPC224 when run under an "NT" operating system. Add the
new ID to the pnp device id table.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 8 Jul 2008 10:06:46 +0000 (03:06 -0700)]
irda: via-ircc proper dma freeing
1. dma should be freed when dma2 request fail.
2. dma2 should be freed too when device close.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: Mark the tsn as received after all allocations finish
If we don't have the buffer space or memory allocations fail,
the data chunk is dropped, but TSN is still reported as received.
This introduced a data loss that can't be recovered. We should
only mark TSNs are received after memory allocations finish.
The one exception is the invalid stream identifier, but that's
due to user error and is reported back to the user.
This was noticed by Michael Tuexen.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Darren Jenkins [Tue, 8 Jul 2008 07:51:44 +0000 (15:51 +0800)]
crypto: tcrypt - Fix memory leak in test_cipher
Coverity CID: 2306 & 2307 RESOURCE_LEAK
In the second for loop in test_cipher(), data is allocated space with
kzalloc() and is only ever freed in an error case.
Looking at this loop, data is written to this memory but nothing seems
to read from it.
So here is a patch removing the allocation, I think this is the right
fix.
Only compile tested.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmailcom> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Firat Birlik [Fri, 4 Jul 2008 03:31:50 +0000 (04:31 +0100)]
zd1211rw: add ID for AirTies WUS-201
I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 3 Jul 2008 17:02:44 +0000 (19:02 +0200)]
mac80211: Only flush workqueue when last interface was removed
Currently the ieee80211_hw->workqueue is flushed each time
an interface is being removed. However most scheduled work
is not interface specific but device specific, for example things like
periodic work for link tuners.
This patch will move the flush_workqueue() call to directly behind
the call to ops->stop() to make sure the workqueue is only flushed
when all interfaces are gone and there really shouldn't be any scheduled
work in the drivers left.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Guy Cohen [Thu, 3 Jul 2008 16:56:13 +0000 (19:56 +0300)]
mac80211: move netif_carrier_on to after ieee80211_bss_info_change_notify
Putting netif_carrier_on before configuring the driver/device with the
new association state may cause a race (tx frames may be sent before
configuration is done)
Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Benny Halevy is seeing extern inlines not resolved with gcc 4.3 with
no-unit-at-a-time
This patch reintroduces unit-at-a-time for gcc >= 4.0, bringing back the
possibility of Uli's crash. If that happens, we'll debug it.
I started seeing both the internal compiler errors and unresolved
inlines on Fedora 9. This patch fixes both problems, without so far
reintroducing the crash reported by Uli.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Cc: Benny Halevy <bhalevy@panasas.com> Cc: Adrian Bunk <bunk@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Ulrich Drepper <drepper@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc: Fix unterminated of_device_id array in legacy_serial.c
A recent patch to legacy_serial.c factored out some code by
using the of_match_node() facility to match a node against
an array of possible matches. However, the patch didn't properly
terminate the array causing potential crashes in cases where no
match is found. In addition, the name of the array was poorly
chosen for a static symbol making debugging harder.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vsprintf: add support for '%pS' and '%pF' pointer formats
They print out a pointer in symbolic format, if possible (ie using
symbolic KALLSYMS information). The '%pS' format is for regular direct
pointers (which can point to data or code and that you find on the stack
during backtraces etc), while '%pF' is for C function pointer types.
On most architectures, the two mean exactly the same thing, but some
architectures use an indirect pointer for C function pointers, where the
function pointer points to a function descriptor (which in turn contains
the actual pointer to the code). The '%pF' code automatically does the
appropriate function descriptor dereference on such architectures.
vsprintf: add infrastructure support for extended '%p' specifiers
This expands the kernel '%p' handling with an arbitrary alphanumberic
specifier extension string immediately following the '%p'. Right now
it's just being ignored, but the next commit will start adding some
specific pointer type extensions.
NOTE! The reason the extension is appended to the '%p' is to allow
minimal gcc type checking: gcc will still see the '%p' and will check
that the argument passed in is indeed a pointer, and yet will not
complain about the extended information that gcc doesn't understand
about (on the other hand, it also won't actually check that the pointer
type and the extension are compatible).
Alphanumeric characters were chosen because there is no sane existing
use for a string format with a hex pointer representation immediately
followed by alphanumerics (which is what such a format string would have
traditionally resulted in).
The actual code is the same, just split out into a helper function.
This makes it easier to read, and allows for simple future extension
of %p handling.
Philipp Zabel [Sat, 5 Jul 2008 23:15:34 +0000 (01:15 +0200)]
pxamci: fix byte aligned DMA transfers
The pxa27x DMA controller defaults to 64-bit alignment. This caused
the SCR reads to fail (and, depending on card type, error out) when
card->raw_scr was not aligned on a 8-byte boundary.
For performance reasons all scatter-gather addresses passed to
pxamci_request should be aligned on 8-byte boundaries, but if
this can't be guaranteed, byte aligned DMA transfers in the
have to be enabled in the controller to get correct behaviour.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Tue, 24 Jun 2008 18:03:14 +0000 (14:03 -0400)]
[SCSI] erase invalid data returned by device
This patch (as1108) fixes a problem that can occur with certain USB
mass-storage devices: They return invalid data together with a residue
indicating that the data should be ignored. Rather than leave the
invalid data in a transfer buffer, where it can get misinterpreted,
the patch clears the invalid portion of the buffer.
This solves a problem (wrong write-protect setting detected) reported
by Maciej Rutecki and Peter Teoh.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Peter Teoh <htmldeveloper@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mark McLoughlin [Fri, 4 Jul 2008 17:23:15 +0000 (18:23 +0100)]
KVM: IOAPIC: Fix level-triggered irq injection hang
The "remote_irr" variable is used to indicate an interrupt
which has been received by the LAPIC, but not acked.
In our EOI handler, we unset remote_irr and re-inject the
interrupt if the interrupt line is still asserted.
However, we do not set remote_irr here, leading to a
situation where if kvm_ioapic_set_irq() is called, then we go
ahead and call ioapic_service(). This means that IRR is
re-asserted even though the interrupt is currently in service
(i.e. LAPIC IRR is cleared and ISR/TMR set)
The issue with this is that when the currently executing
interrupt handler finishes and writes LAPIC EOI, then TMR is
unset and EOI sent to the IOAPIC. Since IRR is now asserted,
but TMR is not, then when the second interrupt is handled,
no EOI is sent and if there is any pending interrupt, it is
not re-injected.
This fixes a hang only seen while running mke2fs -j on an
8Gb virtio disk backed by a fully sparse raw file, with
aliguori "avoid fragmented virtio-blk transfers by copying"
changes.
Signed-off-by: Mark McLoughlin <markmc@redhat.com> Acked-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Anthony Liguori [Thu, 3 Jul 2008 16:02:36 +0000 (19:02 +0300)]
x86: KVM guest: Add memory clobber to hypercalls
Hypercalls can modify arbitrary regions of memory. Make sure to indicate this
in the clobber list. This fixes a hang when using KVM_GUEST kernel built with
GCC 4.3.0.
This was originally spotted and analyzed by Marcelo.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Oliver Hartkopp [Sun, 6 Jul 2008 06:38:43 +0000 (23:38 -0700)]
can: add sanity checks
Even though the CAN netlayer only deals with CAN netdevices, the
netlayer interface to the userspace and to the device layer should
perform some sanity checks.
This patch adds several sanity checks that mainly prevent userspace apps
to send broken content into the system that may be misinterpreted by
some other userspace application.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de> Acked-by: Andre Naujoks <nautsch@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Sat, 5 Jul 2008 08:02:01 +0000 (01:02 -0700)]
Fix pagemap_read() use of struct mm_walk
Fix some issues in pagemap_read noted by Alexey:
- initialize pagemap_walk.mm to "mm" , so the code starts working as
advertised
- initialize ->private to "&pm" so it wouldn't immediately oops in
pagemap_pte_hole()
- unstatic struct pagemap_walk, so two threads won't fsckup each other
(including those started by root, including flipping ->mm when you don't
have permissions)
- pagemap_read() contains two calls to ptrace_may_attach(), second one
looks unneeded.
- avoid possible kmalloc(0) and integer wraparound.
Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Personally, I'd just remove the functionality entirely - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move _RET_IP_ and _THIS_IP_ to include/linux/kernel.h
These two macros are useful beyond lock debugging. Moved definitions from
include/linux/debug_locks.h to include/linux/kernel.h, so code that needs
them does not have to include the former, which would have been a less
intuitive choice of a header.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 ACPI: fix resume from suspend to RAM on uniprocessor x86-64
x86 ACPI: normalize segment descriptor register on resume
ahci: give another shot at clearing all bits in irq_stat
Commit ea0c62f7cf70f13a67830471b613337bd0c9a62e tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read. This patch makes ahci driver
always use the unmasked value to clear irq_status.
While at it, add explanation on the peculiarities of ahci IRQ
clearing.
class->dev_release is called by device_release() iff dev->release
is not present so ide_port_class_release() is never called and the
last hwif->gendev reference is not dropped.
Fix it by removing ide_port_class_release() and get_device() call
from ide_register_port() (device_create_drvdata() takes a hwif->gendev
reference anyway).
This patch fixes hang on wait_for_completion(&hwif->gendev_rel_comp)
in ide_unregister() reported by Pavel Machek.
Cc: Pavel Machek <pavel@suse.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Greg KH <greg@kroah.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Arjan van de Ven [Mon, 16 Jun 2008 22:51:08 +0000 (15:51 -0700)]
softlockup: print a module list on being stuck
Most places in the kernel that go BUG: print a module list
(which is very useful for doing statistics and finding patterns),
however the softlockup detector does not do this yet.
This patch adds the one line change to fix this gap.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>