Following recent changes to ide_hwif_t update the SWARM IDE driver to use
hw_regs_t to initialize port mapping. Plus minor layout adjustments along
the lines of other drivers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Wed, 14 May 2008 20:32:43 +0000 (13:32 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb3: Wrap the software send queue pointer as needed on flush
IB/ipath: Change ipath_devdata.ipath_sdma_status to be unsigned long
IB/ipath: Make ipath_portdata work with struct pid * not pid_t
IB/ipath: Fix RDMA read response sequence checking
IB/ipath: Fix many locking issues when switching to error state
IB/ipath: Fix RC and UC error handling
RDMA/nes: Fix up nes_lro_max_aggr module parameter
Harvey Harrison [Wed, 14 May 2008 01:13:35 +0000 (18:13 -0700)]
b43: use the bitrev helpers rather than rolling a private one
The 4-bit reversal flip_4bit is replaced with the bitrev helper
bitrev8 and a 4-bit shift. The B43_WARN is moved to the location
where a register is read from for checking there. The other caller
explicitly passes an array index which is guaranteed to be within range
and so a B43_WARN is not added there.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Reviewed-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 13 May 2008 01:16:44 +0000 (21:16 -0400)]
ath5k: Fix loop variable initializations
In ath5k_tasklet_rx, both status structures 'rxs' and 'rs' are
initialized at the top of the tasklet, but not within the loop.
If the loop is executed multiple times in the tasklet then the
variables may see changes from previous packets.
For TKIP, this results in 'Invalid Michael MIC' errors if two packets
are processed in the tasklet: rxs.flag gets set to RX_DECRYPTED by
mac80211 when it decrypts the first encrypted packet. The subsequent
packet will have RX_DECRYPTED set upon entry to mac80211, so mac80211
will not try to decrypt it.
We currently initialize all but two fields in the structures, so fix
the other two.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 13 May 2008 13:03:02 +0000 (15:03 +0200)]
mac80211: Set IEEE80211_TXPD_REQ_TX_STATUS for all TX frames
All interfaces should set the IEEE80211_TXPD_REQ_TX_STATUS flag for all TX frames
which will force the master interface to set the IEEE80211_TX_CTL_REQ_TX_STATUS
flag. This in turn will allow drivers to check for that flag before reporting
the TX status to mac80211.
This is very usefull when frames (like beacons, RTS and CTS-to-self) should not
be reported back to mac80211. Later we could add more extensive checks to
exclude more frames from being reported, or let mac80211 decide if it wants
the frame for status reporting or not.
v2: Monitor interfaces should also set IEEE80211_TXPD_REQ_TX_STATUS
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Huang Weiyi [Sat, 10 May 2008 09:12:31 +0000 (11:12 +0200)]
b43: nphy.c remove duplicated include
Remove duplicated include <linux/delay.h> in
drivers/net/wireless/b43/nphy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: Add missing locking to cfg80211_dev_rename
device_rename only performs useful and race free validity
checking at the optional sysfs level so depending on it
for all of the validity checking in cfg80211_dev_rename
is racy.
Instead implement all of the needed validity checking
and locking in cfg80211_dev_rename.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Thu, 8 May 2008 17:15:40 +0000 (19:15 +0200)]
mac80211: use hardware flags for signal/noise units
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
Johannes Berg [Wed, 7 May 2008 21:18:09 +0000 (23:18 +0200)]
mac80211: fix queue constant confusion
In commit 31ccc476b77234f6afb3 (mac80211: QoS related cleanups) I
accidentally changed these to use IEEE80211_MAX_AMPDU_QUEUES twice
which obviously is wrong, it should be IEEE80211_MAX_QUEUES once.
Currently harmless as they're both the same value anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use net_device_stats from net_device structure instead of local.
Kill atmel_get_stats function, because by default it is used
identical internal_stats function from net/core/dev.c
No need to memset stats to 0, because they are allocated by kzalloc.
P.S. Someone should cleanup init_atmel_card function from unneeded
initializations to 0/NULL. Out of scope for this patch.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a hardware scan is completed and another scan is requested in less
than two seconds, iwlwifi will not do the second scan and will pass the
error code -EAGAIN back to mac80211 where it quickly dies. The error
code is not passed along to the calling program wpa_supplicant. After a
timeout, wpa_supplicant will just give up but it will not know why the
scan failed. This is a weakness in the design.
I ran into this issue when I was trying to figure out why it takes more
an a minute for NetworkManager to connect after Networking has been
disabled and then re-enabled. I found a good deal of unnecessary work
being done because mac80211 requests authentication when the interface
is not configured, the ANY mode. I created an experimental passive
(NOTANY) mode for mac80211 to eliminate this case. Then NetworkManager
became so fast that I ran into the iwlwifi 2 second delay next scan
issue which we are discussing.
The patch resolves the problem by bypassing the delay if the scan request
is a direct scan. It should do less harm to the hardware.
Signed-off-by: Bill Moss <bmoss@CLEMSON.EDU> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ester Kummer [Tue, 6 May 2008 03:05:14 +0000 (11:05 +0800)]
iwlwifi: adding parameter of fw_restart
This patch adds a module parameter of fw_restart which determine if
the uCode will be restarted or not in case of error.
Signed-off-by: Ester Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ester Kummer [Tue, 6 May 2008 03:05:12 +0000 (11:05 +0800)]
iwlwifi: update levels of debug prints
This patch updates the levels of debug prints, leaving only one level
in each debug print.
It was anoying and caused unnecessary prints on hot path.
Signed-off-by: Ester Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ester Kummer [Tue, 6 May 2008 03:05:11 +0000 (11:05 +0800)]
iwlwifi: move debug_level to sysfs/bus/pci/devices
This patch ports the debug_level from sysfs/bus/pci/drivers/iwl4965
to /sys/class/net/wlanX/device/debug_level
Signed-off-by: Ester Kummer <ester.kummer@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Mon, 5 May 2008 02:22:51 +0000 (10:22 +0800)]
iwlwifi: fix spinlock used before initialized
The patch fixes spinlock priv->lock (apm_ops.init) is used before it has
been initialized.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: move iwl4965_init_alive_start to iwl-4965.c
This patch moves iwl_4965_init_alive_start to iwl-4965.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Mon, 5 May 2008 02:22:43 +0000 (10:22 +0800)]
iwlwifi: move NIC init and Tx queues init to iwlcore
This patch does the following:
1 - change hw_nic_init from a handler to a function
2 - move hw_nic_init function to iwlcore
3 - open a new file - iwl-tx.c
4 - move all Tx queues initialization (part of NIC init) to iwl-tx.c
5 - move iwl_rx_init, previously as part of the NIC init, to iwl-rx.c
6 - iwl4965_tfd_frame rename to iwl_tfd_frame
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Mon, 5 May 2008 02:22:42 +0000 (10:22 +0800)]
iwlwifi: create disable SCD Tx FIFOs handler
This patch moves disabeling Tx FIFOs in NIC SCD to seperate handlers
in 4965 and 5000 cards.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 5 May 2008 02:22:41 +0000 (10:22 +0800)]
iwlwifi: move iwl4965_set_rxon_ht into iwlcore
This patch moves iwl4965_set_rxon_ht to iwlcore under name
iwl_set_rxon_ht. It also moves collateral changes
iwl_is_channel_extension and iwl_is_fat_tx_allowed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 5 May 2008 02:22:34 +0000 (10:22 +0800)]
iwlwifi: generalize iwl4965_send_add_station function
This patch moves iwl4965_send_add_station to iwlcore
under new name iwl_send_add_sta.
Function uses build command handler in order to support
multiple HWs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 5 May 2008 02:22:32 +0000 (10:22 +0800)]
iwlwifi: debugfs EEPROM dump
This patch adds EEPROM dump in debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 5 May 2008 02:22:30 +0000 (10:22 +0800)]
iwlwifi: don't override association channel with control channel
This patch fixes override of association channel with HT control channel.
The scenario is currently happening because disassociation flow
doesn't clean previous association information (such as is_ht and control
channel).
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Mon, 5 May 2008 02:22:29 +0000 (10:22 +0800)]
iwlwifi-5000: rename iwl5000_init_nic to iwl5000_init_config
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Sun, 4 May 2008 11:48:18 +0000 (14:48 +0300)]
iwlwifi: map A-MPDU HW queue to mac80211 A-MPDU SW queue
This patch maps A-MPDU HW queue to mac80211 SW queue scheme (as introduced
in patch "mac80211: QoS related cleanups"), when trying to perform
ieee80211_wake_queue.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 May 2008 23:02:02 +0000 (01:02 +0200)]
mac80211: proper STA info locking
As discussed earlier, we can unify locking in struct sta_info
and use just a single spinlock protecting all members of the
structure that need protection. Many don't, but one of the
especially bad ones is the 'flags' member that can currently
be clobbered when RX and TX is being processed on different
CPUs at the same time.
Because having four spinlocks for different, mostly exclusive
parts of a single structure is overkill, this patch also kills
the ampdu and mesh plink spinlocks and uses just a single one
for everything. Because none of the spinlocks are nested, this
is safe.
It remains to be seen whether or not we should make the sta
flags use atomic bit operations instead, for now though this
is a safe thing and using atomic operations instead will be
very simple using the new static inline functions this patch
introduces for accessing sta->flags.
Since spin_lock_bh() is used with this lock, there shouldn't
be any contention even if aggregation is enabled at around the
same time as both requires frame transmission/reception which
is in a bh context.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Tomas Winkler <tomasw@gmail.com> Cc: Ron Rindjunsky <ron.rindjunsky@intel.com> Cc: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 May 2008 22:59:37 +0000 (00:59 +0200)]
mac80211: require four hardware queues for QoS/HT
This patch makes mac80211 only announce QoS/HT support when
the underlying hardware has four (or more) queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Ron Rindjunksi <ron.rindjunksi@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Fri, 2 May 2008 20:47:49 +0000 (13:47 -0700)]
b43legacy: replace limit_value macro with clamp_val
kernel-provided clamp_val is identical, delete the private limit_value helper.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Michael Buesch <mb@bu3sch.de> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Fri, 2 May 2008 20:47:48 +0000 (13:47 -0700)]
b43: replace limit_value macro with clamp_val
kernel-provided clamp_val is identical, delete the private limit_value helper.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Michael Buesch <mb@bu3sch.de> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Fri, 2 May 2008 20:47:45 +0000 (13:47 -0700)]
mac80211: tkip.c use kernel-provided infrastructure
Use kernel-provided bit rotation and unaligned access infrastructure rather
than opencoding it.
Some minor spacing adjustments as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Morton [Wed, 14 May 2008 04:05:50 +0000 (21:05 -0700)]
wireless: fix "iwlwifi: unify init driver flow"
drivers/net/wireless/iwlwifi/iwl-core.c: In function 'iwlcore_init_geos':
drivers/net/wireless/iwlwifi/iwl-core.c:323: error: implicit declaration of function 'iwlcore_init_ht_hw_capab'
This (or something like it) should be folded into the base patch to avoid
breaking bisection, please.
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com> Cc: Tomas Winkler <tomas.winkler@intel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
Driver core: struct class remove children list
block: do_mounts - accept root=<non-existant partition>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
USB: atmel_usba_udc fixes, mostly disconnect()
USB: pxa27x_udc: minor fixes
usbtest: comment on why this code "expects" negative and positive errnos
USB: remove PICDEM FS USB demo (04d8:000c) device from ldusb
USB: option: add new Dell 5520 HSDPA variant
USB: unusual_devs: Add support for GI 0401 SD-Card interface
USB: serial gadget: descriptor cleanup
USB: serial gadget: simplify endpoint handling
USB: serial gadget: remove needless data structure
USB: serial gadget: cleanup/reorg
usb: fix compile warning in isp1760
USB: do not handle device 1410:5010 in 'option' driver
USB: Fix unusual_devs.h ordering
USB: add Zoom Telephonics Model 3095F V.92 USB Mini External modem to cdc-acm
USB: Support for the ET502HS HDSPA modem in option driver
USB: Support for the ET502HS HDSPA modem
usb: fix integer as NULL pointer warnings found by sparse
USB: isp1760: fix printk format
USB: add Telstra NextG CDMA id to option driver
USB: add association.h
...
Some devices, like md, may create partitions only at first access,
so allow root= to be set to a valid non-existant partition of an
existing disk. This applies only to non-initramfs root mounting.
This fixes a regression from 2.6.24 which did allow this to happen and
broke some users machines :(
Acked-by: Neil Brown <neilb@suse.de> Tested-by: Joao Luis Meloni Assirati <assirati@nonada.if.usp.br> Cc: stable <stable@kernel.org> Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (73 commits)
net: Fix typo in net/core/sock.c.
ppp: Do not free not yet unregistered net device.
netfilter: xt_iprange: module aliases for xt_iprange
netfilter: ctnetlink: dump conntrack ID in event messages
irda: Fix a misalign access issue. (v2)
sctp: Fix use of uninitialized pointer
cipso: Relax too much careful cipso hash function.
tcp FRTO: work-around inorder receivers
tcp FRTO: Fix fallback to conventional recovery
New maintainer for Intel ethernet adapters
DM9000: Use delayed work to update MII PHY state
DM9000: Update and fix driver debugging messages
DM9000: Add __devinit and __devexit attributes to probe and remove
sky2: fix simple define thinko
[netdrvr] sfc: sfc: Add self-test support
[netdrvr] sfc: Increment rx_reset when reported as driver event
[netdrvr] sfc: Remove unused macro EFX_XAUI_RETRAIN_MAX
[netdrvr] sfc: Fix code formatting
[netdrvr] sfc: Remove kernel-doc comments for removed members of struct efx_nic
[netdrvr] sfc: Remove garbage from comment
...
Nick Piggin [Wed, 14 May 2008 04:37:36 +0000 (06:37 +0200)]
fix SMP data race in pagetable setup vs walking
There is a possible data race in the page table walking code. After the split
ptlock patches, it actually seems to have been introduced to the core code, but
even before that I think it would have impacted some architectures (powerpc
and sparc64, at least, walk the page tables without taking locks eg. see
find_linux_pte()).
The race is as follows:
The pte page is allocated, zeroed, and its struct page gets its spinlock
initialized. The mm-wide ptl is then taken, and then the pte page is inserted
into the pagetables.
At this point, the spinlock is not guaranteed to have ordered the previous
stores to initialize the pte page with the subsequent store to put it in the
page tables. So another Linux page table walker might be walking down (without
any locks, because we have split-leaf-ptls), and find that new pte we've
inserted. It might try to take the spinlock before the store from the other
CPU initializes it. And subsequently it might read a pte_t out before stores
from the other CPU have cleared the memory.
There are also similar races in higher levels of the page tables. They
obviously don't involve the spinlock, but could see uninitialized memory.
Arch code and hardware pagetable walkers that walk the pagetables without
locks could see similar uninitialized memory problems, regardless of whether
split ptes are enabled or not.
I prefer to put the barriers in core code, because that's where the higher
level logic happens, but the page table accessors are per-arch, and open-coding
them everywhere I don't think is an option. I'll put the read-side barriers
in alpha arch code for now (other architectures perform data-dependent loads
in order).
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Wed, 14 May 2008 04:35:11 +0000 (06:35 +0200)]
read_barrier_depends arch fixlets
read_barrie_depends has always been a noop (not a compiler barrier) on all
architectures except SMP alpha. This brings UP alpha and frv into line with all
other architectures, and fixes incorrect documentation.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Sun, 11 May 2008 05:46:38 +0000 (22:46 -0700)]
USB: atmel_usba_udc fixes, mostly disconnect()
Various fixes to Atmel's high speed UDC driver.
* Issue some missing disconnect() calls. Currently they are only made
when VBUS power goes away (on boards where the driver can sense such
changes), but that's not enough for gadget drivers to clean out all
the state that's needed. Missing calls were:
- After USB reset, before starting enumeration.
- When unregistering a gadget driver, before unbind().
* Don't assume gadget drivers provide disconnect callbacks; make sure
to not call through a null pointer!
* When the driver doesn't provide an unbind() callback, refuse to
unregister it.
Also remove two bogus "error" messages:
* Related to mis-handling of disconnect() ... don't emit error messages
for disconnect() handlers that disable endpoints. All of them should
be doing that; the problem is (unfixed) oddness in atmel_usba_udc.
* Don't emit a diagnostic for a curious and transient nonfatal error
that shows up sometimes with EP0.
Those messages spammed syslog, for no good reason.
Robert Jarzmik [Mon, 12 May 2008 17:47:56 +0000 (10:47 -0700)]
USB: pxa27x_udc: minor fixes
Minor fixes to pxa27x udc driver :
- don't clobber driver model bus_id field
- wrong endianess fix (no functional change; cpu is little-endian)
- double udc disable fix
- resume/suspend fix (OTG hold bit)
- make driver pxa27x dependant (check cpu at runtime)
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcin Slusarz [Mon, 12 May 2008 18:17:25 +0000 (20:17 +0200)]
usbtest: comment on why this code "expects" negative and positive errnos
On Mon, May 12, 2008 at 01:02:22AM -0700, David Brownell wrote:
> On Sunday 11 May 2008, Marcin Slusarz wrote:
> >
> > test_ctrl_queue expects (?) positive and negative errnos.
> > what is going on here?
>
> The sign is just a way to flag something:
>
> /* some faults are allowed, not required */
>
> The negative ones are required. Positive codes are optional,
> in the sense that, depending on how the peripheral happens
> to be implemented, they won't necessarily be triggered.
>
> For example, the test to fetch a device qualifier desriptor
> must succeed if the device is running at high speed. So that
> test is marked as negative. But when it's full speed, it
> could legitimately fail; marked as positive. And so on for
> other tests.
>
> Look at how the codes are *interpreted* to see it work.
Lets document it.
Based on comment from David Brownell <david-b@pacbell.net>.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Xiaofan Chen [Tue, 13 May 2008 13:52:00 +0000 (21:52 +0800)]
USB: remove PICDEM FS USB demo (04d8:000c) device from ldusb
Microchip has changed the PICDEM FS USB demo device (0x04d8:000c)
to use bulk transfer and not interrupt transfer. So I've updated the libusb
based program here (Post #31).
http://forum.microchip.com/tm.aspx?m=106426&mpage=2
So I believe that the in-kernel ldusb driver will no longer work with the
demo firmware. It should be removed.
Filip Aben [Thu, 8 May 2008 17:48:12 +0000 (10:48 -0700)]
USB: unusual_devs: Add support for GI 0401 SD-Card interface
Enables the SD-Card interface on the GI 0401 HSUPA card from Option.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.
This revised patch adds a small comment explaining why and reduces the
rev range.
David Brownell [Wed, 7 May 2008 21:27:37 +0000 (14:27 -0700)]
USB: serial gadget: descriptor cleanup
Bugfix some serial gadget descriptors:
- Stop mangling the low bits (controller type ID) of bcdDevice;
just use the high bits for a driver revision code.
- Serial numbers that aren't specific to individual devices
are useless; stop reporting "0" for this.
- Since it's not part of a CDC-conformant function, the "bulk only"
configuration shouldn't be using "CDC Data" as its interface class.
Switch over to using CLASS_VENDOR_SPEC (different value, 0xff).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 21:25:24 +0000 (14:25 -0700)]
USB: serial gadget: simplify endpoint handling
Switch serial gadget away from a *very* old idiom: just remember
the endpoints we'll be using, instead of looking them up by name
each time. This is a net code and data (globals) shrink.
Also fix a small memory leak in the rmmod path, by working the
same as the disconnect code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 21:24:10 +0000 (14:24 -0700)]
USB: serial gadget: remove needless data structure
This removes a needless data structure from the serial gadget code;
it's a small code shrink, and a larger data shrink.
Since "struct usb_request" already has a "struct list_head" reserved
for use by gadget drivers, the serial gadget code doesn't need to
allocate wrapper structs to hold that list ... it can (and should!)
just use the list_head provided for that exact use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 7 May 2008 23:00:36 +0000 (16:00 -0700)]
USB: serial gadget: cleanup/reorg
Some cleanup/reorg of g_serial ... simplifying it, and disentangling
its structure so morphing it into a "function" driver (combinable with
other interfaces) should be less painful.
- Remove most forward declarations
* put tty and gadget driver structs after their contents
* snug module init/exit decls next to their functions
* reordered some functions
- Other cleanup:
* convert a funky macro to an inline function
* snug up module params next to their declarations
* add missing driver.owner
* add separator lines between major driver sections
- Add comments re potential parameter/#define changes:
* only supports one port (shrank GS_NUM_PORTS)
* changing from 9600-8-N-1 affects multiple sites
- Remove net2280-specific optimization ... it was being done
way too late, can be done by net2280 module options, and in
any case doesn't matter at any sane serial data rates.
There are no behavioral changes, but the macro thing saves I-space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Al Borchers <alborchers@steinerpoint.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:
% lsusb -v -d 1410:4400 | grep InterfaceClass
bInterfaceClass 255 Vendor Specific Class
bInterfaceClass 255 Vendor Specific Class
Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Iain McFarlane [Sat, 3 May 2008 23:13:49 +0000 (00:13 +0100)]
USB: add Zoom Telephonics Model 3095F V.92 USB Mini External modem to cdc-acm
The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:
May 3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May 3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22
Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
USB: Support for the ET502HS HDSPA modem in option driver
the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Harvey Harrison [Wed, 30 Apr 2008 22:03:41 +0000 (15:03 -0700)]
usb: fix integer as NULL pointer warnings found by sparse
drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Wed, 30 Apr 2008 20:53:54 +0000 (13:53 -0700)]
USB: isp1760: fix printk format
Fix printk format warnings in isp1760 (in linux-next):
next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 Apr 2008 19:37:19 +0000 (15:37 -0400)]
USB: create attributes before sending uevent
This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.
Unfortunately there are a few attributes which cannot be created that
early. The "descriptors" attribute is binary and so must be created
separately. The power-management attributes can't be created until
the dev/power/ group exists. And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Oester [Wed, 14 May 2008 06:27:48 +0000 (23:27 -0700)]
netfilter: xt_iprange: module aliases for xt_iprange
Using iptables 1.3.8 with kernel 2.6.25, rules which include '-m
iprange' don't automatically pull in xt_iprange module. Below patch
adds module aliases to fix that. Patch against latest -git, but seems
like a good candidate for -stable also.
Signed-off-by: Phil Oester <kernel@linuxace.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Wed, 14 May 2008 06:27:11 +0000 (23:27 -0700)]
netfilter: ctnetlink: dump conntrack ID in event messages
Conntrack ID is not put (anymore ?) in event messages. This causes
current ulogd2 code to fail because it uses the ID to build a hash in
userspace. This hash is used to be able to output the starting time of
a connection.
Conntrack ID can be used in userspace application to maintain an easy
match between kernel connections list and userspace one. It may worth
to add it if there is no performance related issue.
[ Patrick: it was never included in events, but really should be ]
Signed-off-by: Eric Leblond <eric@inl.fr> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 14 May 2008 06:25:00 +0000 (23:25 -0700)]
sctp: Fix use of uninitialized pointer
Introduced by c4492586 (sctp: Add address type check while process
paramaters of ASCONF chunk):
net/sctp/sm_make_chunk.c: In function 'sctp_process_asconf':
net/sctp/sm_make_chunk.c:2828: warning: 'addr_param' may be used uninitialized in this function
net/sctp/sm_make_chunk.c:2828: note: 'addr_param' was declared here
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 14 May 2008 06:23:55 +0000 (23:23 -0700)]
cipso: Relax too much careful cipso hash function.
The cipso_v4_cache is allocated to contain CIPSO_V4_CACHE_BUCKETS
buckets. The CIPSO_V4_CACHE_BUCKETS = 1 << CIPSO_V4_CACHE_BUCKETBITS,
where CIPSO_V4_CACHE_BUCKETBITS = 7.
The bucket-selection function for this hash is calculated like this:
bkt = hash & (CIPSO_V4_CACHE_BUCKETBITS - 1);
^^^
i.e. picking only 4 buckets of possible 128 :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
V4L/DVB (7900): pvrusb: Fix Kconfig if DVB=m V4L_core=y
As reported by Ingo Molnar:
x86.git testing found the following build failure:
drivers/built-in.o: In function `pvr2_dvb_feed_thread':
pvrusb2-dvb.c:(.text+0x127e78): undefined reference to `dvb_dmx_swfilter'
drivers/built-in.o: In function `pvr2_dvb_adapter_exit':
pvrusb2-dvb.c:(.text+0x128357): undefined reference to `dvb_net_release'
pvrusb2-dvb.c:(.text+0x12836f): undefined reference to `dvb_dmxdev_release'
[...]
If one of DVB_CORE or VIDEO_DEV is a module, the modules that can be used by
both DVB and V4L cores should also be a module, otherwise, it will break its
dependencies. This Kconfig logic implements the following:
CONFIG_VIDEO_DEV CONFIG_DVB_CORE CONFIG_VIDEO_MEDIA
N N N
N M M
N Y Y
M N M
M M M
M Y M
Y N Y
Y M M
Y Y Y
Michael Krufky [Sat, 10 May 2008 17:34:09 +0000 (14:34 -0300)]
V4L/DVB (7893): xc5000: bug-fix: allow multiple devices in a single system
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Mon, 12 May 2008 18:01:27 +0000 (15:01 -0300)]
V4L/DVB (7891): cx18/ivtv: fix open() kernel oops
Upon error conditions in cx18/ivtv_probe(), the code at the 'err:' label
leaves a NULL entry in cx18/ivtv_cards[]. This can cause a NULL pointer
de-reference in cx18/ivtv_v4l2_open() which is fixed by this patch.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6-omap-h63xx.git / log