Adrian Bunk [Wed, 18 Jun 2008 00:36:50 +0000 (03:36 +0300)]
sh/kernel/ cleanups
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 3 Jun 2008 09:54:02 +0000 (18:54 +0900)]
sh: Add support for 16kB PAGE_SIZE.
16kB is a useful size on nommu, while 64kB still tends to be too big to
be useful. Newer MMUs are likely to support this as well, so plug it
in in anticipation of those, too.
Paul Mundt [Mon, 19 May 2008 05:00:44 +0000 (14:00 +0900)]
sh: Make dump_task dependent on ELF core.
Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.
Paul Mundt [Mon, 19 May 2008 04:34:45 +0000 (13:34 +0900)]
binfmt_elf_fdpic: Magical stack pointer index, for NEW_AUX_ENT compat.
While implementing binfmt_elf_fdpic on SH it quickly became apparent
that SH was the first platform to support both binfmt_elf_fdpic and
binfmt_elf, as well as the only of the FDPIC platforms to make use of the
auxvt.
Currently binfmt_elf_fdpic uses a special version of NEW_AUX_ENT() where
the first argument is the entry displacement after csp has been adjusted,
being reset after each adjustment. As we have no ability to sort this out
through the platform's ARCH_DLINFO, this index needs to be managed
entirely in create_elf_fdpic_tables(). Presently none of the platforms
that set their own auxvt entries are able to do so through their
respective ARCH_DLINFOs when using binfmt_elf_fdpic.
In addition to this, binfmt_elf_fdpic has been looking at
DLINFO_ARCH_ITEMS for the number of architecture-specific entries in the
auxvt. This is legacy cruft, and is not defined by any platforms in-tree,
even those that make heavy use of the auxvt. AT_VECTOR_SIZE_ARCH is
always available, and contains the number that is of interest here, so we
switch to using that unconditionally as well.
As this has direct bearing on how much stack is used, platforms that have
configurable (or dynamically adjustable) NEW_AUX_ENT calls need to either
make AT_VECTOR_SIZE_ARCH more fine-grained, or leave it as a worst-case
and live with some lost stack space if those entries aren't pushed (some
platforms may also need to purposely sacrifice some space here for
alignment considerations, as noted in the code -- although not an issue
for any FDPIC-capable platform today).
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: David Howells <dhowells@redhat.com>
powerpc: Disable 64K hugetlb support when doing 64K SPU mappings
The 64K SPU local store mapping feature is incompatible with the
64K huge pages support due to the inability of some parts of
the memory management to differenciate between them while they
use a different page table format.
For now, disable 64K huge pages when CONFIG_SPU_FS_64K_LS,
in the long run, this can be fixed by making this feature use
the hugetlb page table format.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/powermac: Fixup default serial port device for pmac_zilog
This removes the non-working code in legacy_serial that tried to handle
the powermac SCC ports, and instead add a (now working) function to the
powermac platform code to find the default serial console if any.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/powermac: Use sane default baudrate for SCC debugging
When using the "sccdbg" option to route early kernel messages and
xmon to the SCC serial port on PowerMacs, when this wasn't the
configured output port of Open Firmware, we initialize the baudrate
to 57600bps. This isn't a very good default on some powermacs where
both the FW and pmac_zilog will default to 38400. This fixes it to
use the same logic as pmac_zilog to pick a default speed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nick Piggin [Mon, 28 Jul 2008 03:28:03 +0000 (20:28 -0700)]
powerpc/mm: Implement _PAGE_SPECIAL & pte_special() for 64-bit
Implement _PAGE_SPECIAL and pte_special() for 64-bit powerpc. This bit will
be used by the fast get_user_pages() to differenciate PTEs that correspond
to a valid struct page from special mappings that don't such as IO mappings
obtained via io_remap_pfn_ranges().
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Hugh Dickins <hugh@veritas.com> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Show processor cache information in sysfs
Collect cache information from the OF device tree and display it in
the cpu hierarchy in sysfs. This is intended to be compatible at the
userspace level with x86's implementation[1], hence some of the funny
attribute names. The arrangement of cache info is not immediately
intuitive, but (again) it's for compatibility's sake.
The cache attributes exposed are:
type (Data, Instruction, or Unified)
level (1, 2, 3...)
size
coherency_line_size
number_of_sets
ways_of_associativity
All of these can be derived on platforms that follow the OF PowerPC
Processor binding. The code "publishes" only those attributes for
which it is able to determine values; attributes for values which
cannot be determined are not created at all.
[1] arch/x86/kernel/cpu/intel_cacheinfo.c
BenH: Turned some printk's into pr_debug, added better NULL checking
in a couple of places.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make core id information available to userspace
Existing Open Firmware practice is to report each processor core as a
separate node in the device tree. Report the value of the "reg" OF
property corresponding to a logical CPU's device node as the core_id
attribute in /sys/devices/system/cpu/cpu*/topology/core_id.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Make core sibling information available to userspace
Implement the notion of "core siblings" for powerpc. This makes
/sys/devices/system/cpu/cpu*/topology/core_siblings present sensible
values, indicating online CPUs which share an L2 cache.
BenH: Made cpu_to_l2cache() use of_find_node_by_phandle() instead
of IBM-specific open coded search
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Sun, 27 Jul 2008 16:14:24 +0000 (02:14 +1000)]
ibmveth: Fix multiple errors with dma_mapping_error conversion
The addition of an argument to dma_mapping_error() in commit 8d8bb39b9eba32dd70e87fd5ad5c5dd4ba118e06 "dma-mapping: add the device
argument to dma_mapping_error()" left a bit of fallout:
drivers/net/ibmveth.c:263: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:264: error: expected ')' before 'goto'
drivers/net/ibmveth.c:284: error: expected expression before '}' token
drivers/net/ibmveth.c:297: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:298: error: expected ')' before 'dma_unmap_single'
drivers/net/ibmveth.c:306: error: expected expression before '}' token
drivers/net/ibmveth.c:491: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: too few arguments to function 'dma_mapping_error'
drivers/net/ibmveth.c:927: error: expected ')' before '{' token
drivers/net/ibmveth.c:974: error: expected expression before '}' token
drivers/net/ibmveth.c:914: error: label 'out' used but not defined m
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Rothwell [Sun, 27 Jul 2008 14:51:02 +0000 (00:51 +1000)]
powerpc/pseries: Fix CMO sysdev attribute API change fallout
Noticed due to these wanings:
arch/powerpc/platforms/pseries/cmm.c:298: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:299: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Roland McGrath [Sun, 27 Jul 2008 06:52:52 +0000 (16:52 +1000)]
powerpc: Add TIF_NOTIFY_RESUME support for tracehook
This adds TIF_NOTIFY_RESUME support for powerpc. When set,
we call tracehook_notify_resume() on the way to user mode.
This overloads do_signal() to do the work, but changes its
arguments to it has the TIF_* bits handy in a register and
drops the useless first argument that was always zero.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Roland McGrath [Sun, 27 Jul 2008 06:49:50 +0000 (16:49 +1000)]
powerpc: Call tracehook_signal_handler() when setting up signal frames
This makes the powerpc signal handling code call tracehook_signal_handler()
after a handler is set up. This means that using PTRACE_SINGLESTEP to
enter a signal handler will report to ptrace on the first instruction of
the handler, instead of the second. This is consistent with what x86 and
other machines do, and what users and debuggers want.
BenH: Fixed up the test for the trap value.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rather doing one initialization pass over all the per-cpu
cpu_sibling_maps at boot, update the maps at cpu online/offline time.
This is a behavior change -- the thread_siblings attribute now
reflects only online siblings, whereas it would display offline
siblings before. The new behavior matches that of x86, and is
arguably more useful.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This piece of code is broken for >2 threads, and possibly in some
other subtle ways (such as comparing a value obtained from an
"ibm,ppc-interrupt-server#s" property to a value obtained from a
"reg" property) and doesn't seem to have any useful purpose in the
first place other than a dubious warning in case NR_CPUS is too
small, which probably isn't the right place to do so.
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kumar Gala [Sat, 26 Jul 2008 17:57:30 +0000 (03:57 +1000)]
powerpc: Fix 8xx build failure
The 'powerpc ioremap_prot' broke 8xx builds:
include2/asm/pgtable-ppc32.h:555: error: '_PAGE_WRITETHRU' undeclared (first use in this function)
include2/asm/pgtable-ppc32.h:555: error: (Each undeclared identifier is reported only once
include2/asm/pgtable-ppc32.h:555: error: for each function it appears in.)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kernel/vio.c:1034: warning: function declaration isnâ\80\99t a prototype
arch/powerpc/kernel/vio.c:1035: warning: function declaration isnâ\80\99t a prototype
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kumar Gala [Fri, 25 Jul 2008 19:27:33 +0000 (05:27 +1000)]
powerpc/booke: Clean up the hardware watchpoint support
* CONFIG_BOOKE is selected by CONFIG_44x so we dont need both
* Fixed a few comments
* Go back to only using DBCR0_IDM to determine if we are using
debug resources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rusty Russell [Mon, 28 Jul 2008 17:16:30 +0000 (12:16 -0500)]
stop_machine(): stop_machine_run() changed to use cpu mask
Instead of a "cpu" arg with magic values NR_CPUS (any cpu) and ~0 (all
cpus), pass a cpumask_t. Allow NULL for the common case (where we
don't care which CPU the function is run on): temporary cpumask_t's
are usually considered bad for stack space.
This deprecates stop_machine_run, to be removed soon when all the
callers are dead.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Mon, 28 Jul 2008 17:16:29 +0000 (12:16 -0500)]
Hotplug CPU: don't check cpu_online after take_cpu_down
Akinobu points out that if take_cpu_down() succeeds, the cpu must be offline.
Remove the cpu_online() check, and put a BUG_ON().
Quoting Akinobu Mita:
Actually the cpu_online() check was necessary before appling this
stop_machine: simplify patch.
With old __stop_machine_run(), __stop_machine_run() could succeed
(return !IS_ERR(p) value) even if take_cpu_down() returned non-zero value.
The return value of take_cpu_down() was obtained through kthread_stop()..
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: "Akinobu Mita" <akinobu.mita@gmail.com>
Rusty Russell [Mon, 28 Jul 2008 17:16:28 +0000 (12:16 -0500)]
Simplify stop_machine
stop_machine creates a kthread which creates kernel threads. We can
create those threads directly and simplify things a little. Some care
must be taken with CPU hotunplug, which has special needs, but that code
seems more robust than it was in the past.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Jason Baron [Thu, 28 Feb 2008 16:33:03 +0000 (11:33 -0500)]
stop_machine: add ALL_CPUS option
-allow stop_mahcine_run() to call a function on all cpus. Calling
stop_machine_run() with a 'ALL_CPUS' invokes this new behavior.
stop_machine_run() proceeds as normal until the calling cpu has
invoked 'fn'. Then, we tell all the other cpus to call 'fn'.
Signed-off-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> CC: Adrian Bunk <bunk@stusta.de> CC: Andi Kleen <andi@firstfloor.org> CC: Alexey Dobriyan <adobriyan@gmail.com> CC: Christoph Hellwig <hch@infradead.org> CC: mingo@elte.hu CC: akpm@osdl.org
Merge branch 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure we call nfs_sb_deactive() after releasing the directory inode
nfs_remount oops when rebooting + possible fix
V4L/DVB (8549): mxl5007: Fix an error at include file
mxl5007 was forcing for its compilation:
In file included from drivers/media/common/tuners/mxl5007t.c:25:drivers/media/common/tuners/mxl5007t.h:80:1: warning: "CONFIG_MEDIA_TUNER_MXL5007T" redefined
In file included from <command-line>:0:
./include/linux/autoconf.h:2782:1: warning: this is the location of the previous definition
Probably, some temporary hack for testing.
Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
NFS: Ensure we call nfs_sb_deactive() after releasing the directory inode
In order to avoid the "Busy inodes after unmount" error message, we need to
ensure that nfs_async_unlink_release() releases the super block after the
call to nfs_free_unlinkdata().
The new super.c:nfs_remount function doesn't check the validity of the
options/options4 pointers. Unfortunately, this seems to happend.
The obvious patch seems to check the pointers, and not to do anything if
the happend to be NULL.
Tested on an XScale PXA255 system, latest git.
Regards,
M.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hans Verkuil [Sun, 27 Jul 2008 17:08:54 +0000 (14:08 -0300)]
V4L/DVB (8546): saa7146: fix read from uninitialized memory
The offset field of the scatterlist entry *after* the last valid scatterlist
entry was used instead of the first scatterlist entry (as was the intention
of this code).
This worked fine until the kzalloc of the sglist was replaced with kmalloc
and sg_init_table only zeroed the exact needed length. Apparently kzalloc
zeroes a bit more than is strictly necessary so the offset field was
always 0 in the past.
But now the offset field was suddenly random and this led to broken captures.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Neukum [Sun, 27 Jul 2008 17:01:59 +0000 (14:01 -0300)]
V4L/DVB (8544): gspca: probe/open race.
The device is flagged present after it is registered. During that window calls
to open() that should work fail with -ENODEV. Reversing the order fixes
the race.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The rest was an update of the top-level Makefile to use sparc
for header files when sparc64 is being build.
And a small fixlet to pick up the correct unistd.h from
sparc64 code.
Thomas Gleixner [Sun, 27 Jul 2008 19:43:11 +0000 (21:43 +0200)]
x86: fix cpu hotplug on 32bit
commit 3e9704739daf46a8ba6593d749c67b5f7cd633d2 ("x86: boot secondary
cpus through initial_code") causes the kernel to crash when a CPU is
brought online after the read only sections have been write
protected. The write to initial_code in do_boot_cpu() fails.
Move inital_code to .cpuinit.data section.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: H. Peter Anvin <hpa@zytor.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: state userland requirements in Kconfig help
firewire: avoid memleak after phy config transmit failure
firewire: fw-ohci: TSB43AB22/A dualbuffer workaround
firewire: queue the right number of data
firewire: warn on unfinished transactions during card removal
firewire: small fw_fill_request cleanup
firewire: fully initialize fw_transaction before marking it pending
firewire: fix race of bus reset with request transmission
V4L/DVB (8539): em28xx-cards: New supported IDs for analog models
- New supported IDs for analog models
(Based on Markus Rechberger <mrechberger@gmail.com> version of em28xx driver)
- Validation field for new em28xx boards.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
[mchehab@infradead.org: Need to fix some merge conflicts] Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (59 commits)
[SCSI] replace __FUNCTION__ with __func__
[SCSI] extend the last_sector_bug flag to cover more sectors
[SCSI] qla2xxx: Update version number to 8.02.01-k6.
[SCSI] qla2xxx: Additional NPIV corrections.
[SCSI] qla2xxx: suppress uninitialized-var warning
[SCSI] qla2xxx: use memory_read_from_buffer()
[SCSI] qla2xxx: Issue proper ISP callbacks during stop-firmware.
[SCSI] ch: fix ch_remove oops
[SCSI] 3w-9xxx: add MSI support and misc fixes
[SCSI] scsi_lib: use blk_rq_tagged in scsi_request_fn
[SCSI] ibmvfc: Update driver version to 1.0.1
[SCSI] ibmvfc: Add ADISC support
[SCSI] ibmvfc: Miscellaneous fixes
[SCSI] ibmvfc: Fix hang on module removal
[SCSI] ibmvfc: Target refcounting fixes
[SCSI] ibmvfc: Reduce unnecessary log noise
[SCSI] sym53c8xx: free luntbl in sym_hcb_free
[SCSI] scsi_scan.c: Release mutex in error handling code
[SCSI] scsi_eh_prep_cmnd should save scmd->underflow
[SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: some mmc/sd cleanups
include/video/atmel_lcdc.h must #include <linux/workqueue.h>
avr32: allow system timer to share interrupt to make OProfile work
drivers/misc/atmel-ssc.c: Removed duplicated include
avr32: Add platform data for AC97C platform device
avr32: clean up mci platform code
fix avr32 build errors
Merge branch 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: ppc: fix invalidation of large guest pages
KVM: s390: Fix possible host kernel bug on lctl(g) handling
KVM: s390: Fix instruction naming for lctlg
KVM: s390: Fix program check on interrupt delivery handling
KVM: s390: Change guestaddr type in gaccess
KVM: s390: Fix guest kconfig
KVM: s390: Advertise KVM_CAP_USER_MEMORY
KVM: ia64: Fix irq disabling leak in error handling code
KVM: VMX: Fix undefined beaviour of EPT after reload kvm-intel.ko
KVM: VMX: Fix bypass_guest_pf enabling when disable EPT in module parameter
KVM: task switch: translate guest segment limit to virt-extension byte granular field
KVM: Avoid instruction emulation when event delivery is pending
KVM: task switch: use seg regs provided by subarch instead of reading from GDT
KVM: task switch: segment base is linear address
KVM: SVM: allow enabling/disabling NPT by reloading only the architecture module
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
setlocalversion: do not describe if there is nothing to describe
kconfig: fix typos: "Suport" -> "Support"
kconfig: make defconfig is no longer chatty
kconfig: make oldconfig is now less chatty
kconfig: speed up all*config + randconfig
kconfig: set all new symbols automatically
kconfig: add diffconfig utility
kbuild: remove Module.markers during mrproper
kbuild: sparse needs CF not CHECKFLAGS
kernel-doc: handle/strip __init
vmlinux.lds: move __attribute__((__cold__)) functions back into final .text section
init: fix URL of "The GNU Accounting Utilities"
kbuild: add arch/$ARCH/include to search path
kbuild: asm symlink support for arch/$ARCH/include
kbuild: support arch/$ARCH/include for tags, cscope
kbuild: prepare headers_* for arch/$ARCH/include
kbuild: install all headers when arch is changed
kbuild: make clean removes *.o.* as well
kbuild: optimize headers_* targets
kbuild: only one call for include/ in make headers_*
...
Andrea Righi [Sun, 27 Jul 2008 15:29:15 +0000 (17:29 +0200)]
task IO accounting: improve code readability
Put all i/o statistics in struct proc_io_accounting and use inline functions to
initialize and increment statistics, removing a lot of single variable
assignments.
This also reduces the kernel size as following (with CONFIG_TASK_XACCT=y and
CONFIG_TASK_IO_ACCOUNTING=y).
text data bss dec hex filename
11651 0 0 11651 2d83 kernel/exit.o.before
11619 0 0 11619 2d63 kernel/exit.o.after
10886 132 136 11154 2b92 kernel/fork.o.before
10758 132 136 11026 2b12 kernel/fork.o.after
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Allow to force model to intel-mac-v3 in snd_hda_intel (sigmatel).
ALSA: cs4232: fix crash during chip PNP detection
ALSA: hda - Add automatic model setting for the Acer Aspire 5920G laptop
ALSA: make snd_ac97_add_vmaster() static
ALSA: sound/pci/azt3328.h: no variables for enums
ALSA: soc - wm9712 mono mixer
ALSA: hda - Add support of ASUS Eeepc P90*
ALSA: opti9xx: no isapnp param for !CONFIG_PNP
ALSA: opti93x - Fix NULL dereference
ALSA: hda - Added support for Asus V1Sn
ALSA: ASoC: Factor PGA DAPM handling into main
ALSA: ASoC: Refactor DAPM event handler
ALSA: ALSA: ens1370: communicate PCI device to AC97
ALSA: ens1370: SRC stands for Sample Rate Converter
ALSA: hda - Align BDL position adjustment parameter
ALSA: Au1xpsc: psc not disabled when TX is idle
ALSA: add TriTech 28023 AC97 codec ID and Wolfson 9701 name.
projects / linux-2.6-omap-h63xx.git / log