Darrick J. Wong [Fri, 15 Aug 2008 07:40:41 +0000 (00:40 -0700)]
ibmaem: don't query the entire sensor repository when reading energy meter
Currently, all sensors are read when the energy meter is queried via
sysfs. This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use. Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 15 Aug 2008 07:40:40 +0000 (00:40 -0700)]
ibmaem: prevent infinite probing loop on x3650 M2 systems
On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing. On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes. This causes the probe function to run
in an infinite loop. To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 15 Aug 2008 07:40:40 +0000 (00:40 -0700)]
ibmaem: update the documentation to reflect the current name
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards. However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp. the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.
At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards. This patch only implements DMI
probing for the IP35 Pro. For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.
The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards). Ideally in the longer term this manual probing method
would be removed.
This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hans passed maintainership of the abituguru3 hwmon driver onto me. Add
a new entry to the MAINTAINERS file for the abituguru3 driver and assign
it to me. Also update the existing UGURU entry to indicate that Hans is
only responsible for the abituguru driver.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl> Cc: Jean Delvare <khali@linux-fr.org> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darrick J. Wong [Fri, 15 Aug 2008 07:40:36 +0000 (00:40 -0700)]
i5k_amb: provide labels for temperature sensors
Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marc Pignat [Fri, 15 Aug 2008 07:40:34 +0000 (00:40 -0700)]
hwmon: ADC124S501 generic driver
SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...
Code for 8 channels by Tobias Himmer.
This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Cc: Tobias Himmer <tobias@himmer-online.de> Cc: "Mark M. Hoffman" <mhoffman@lightlink.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roberto De Ioris [Fri, 15 Aug 2008 07:40:30 +0000 (00:40 -0700)]
applesmc: support for Intel iMac
This adds support for fans and temperature sensors on intel iMac.
Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors:
cpu A
ambient
gpu
gpu diode
gpu heatsink
hd bay 1
memory controller
optical drive
power
Signed-off-by: Roberto De Ioris <roberto@unbit.it> Cc: Nicolas Boichat <nicolas@boichat.ch> Cc: Jean Delvare <khali@linux-fr.org> Cc: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
York Sun [Fri, 15 Aug 2008 07:40:29 +0000 (00:40 -0700)]
freescale DIU: bug fix: add sanity check for AOI position
AOI position cannot be negative.
Signed-off-by: York Sun <yorksun@freescale.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
York Sun [Fri, 15 Aug 2008 07:40:28 +0000 (00:40 -0700)]
freescale DIU: add virtual resolution and panning support
Application can now have the virtual resoltuion and use FBIOPAN_DISPLAY
ioctl to pan.
Signed-off-by: York Sun <yorksun@freescale.com> Cc: Kumar Gala <galak@gate.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Fri, 15 Aug 2008 07:40:26 +0000 (00:40 -0700)]
kexec jump: fix for ftrace
Ftrace depends on some processor state that we destroyed during kexec and
restored by restore_processor_state(). So save_processor_state() and
restore_processor_state() are moved into machine_kexec() and ftrace is
restored after restore_processor_state().
Signed-off-by: Huang Ying <ying.huang@intel.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Fri, 15 Aug 2008 07:40:25 +0000 (00:40 -0700)]
kexec jump: __ftrace_enabled_save/restore
Add __ftrace_enabled_save/restore, used to disable ftrace for a while.
Now, this is used by kexec jump, which need a version without lock, for
general situation, a locked version should be used.
Signed-off-by: Huang Ying <ying.huang@intel.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Fri, 15 Aug 2008 07:40:22 +0000 (00:40 -0700)]
kexec jump: rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE
Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control
page is used for not only code on some platform. For example in kexec
jump, it is used for data and stack too.
[akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion] Signed-off-by: Huang Ying <ying.huang@intel.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.text+0xe684): Section mismatch in reference from the function register_nosave_region() to the function .init.text:__register_nosave_region()
The function register_nosave_region() references
the function __init __register_nosave_region().
This is often because register_nosave_region lacks a __init
annotation or the annotation of __register_nosave_region is wrong.
register_nosave_region calls __init function and is called only from
__init functions
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Kerrisk [Fri, 15 Aug 2008 07:40:18 +0000 (00:40 -0700)]
Documentation/vm/page_migration: update reference to numa_maps + fix download URI
With man-pages-3.07, the numa_maps documentation home is now proc(5), so
the reference in Documentation/vm/page_migration needs updating.
(Cliff/Lee are removing numa_maps.5 from the numactl package.) Also, the
download location for the numactl package changed a while back. This
patch fixes both things, as well as a typo (provided-->provides).
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Cliff Wickman <cpw@sgi.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-you can see that the condition is true, so it assigns start_off =
ALIGN(bdata->last_end_off, align); (that is PAGE_SIZE) and allocates
over already allocated block.
With the patch it tries to continue at the end of previous allocation only
if the previous allocation ended in the middle of the page.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Johannes Weiner <hannes@saeurebad.de> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Rottmann [Mon, 4 Aug 2008 12:40:16 +0000 (14:40 +0200)]
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
Adds a simple IRQ autodetection to the AMD Geode MFGPT driver, and more
importantly, adds some checks, if IRQs can actually be received on the
chosen line. This fixes cases where MFGPT is selected as clocksource
though not producing any ticks, so the kernel simply starves during
boot.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de> Cc: Andres Salomon <dilinger@debian.org> Cc: linux-geode@bombadil.infradead.org Cc: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hugh Dickins [Fri, 15 Aug 2008 12:58:32 +0000 (13:58 +0100)]
x86: fix /proc/meminfo DirectMap
Do we actually want these DirectMap lines in the x86 /proc/meminfo?
I can see they're interesting to CPA developers and TLB optimizers,
but they don't fit its usual "where has all my memory gone?" usage.
If they are to stay, here are some fixes.
1. On x86_32 without PAE, they're not 2M but 4M pages: no need to
mess with the internal enum, but show the right name to users.
2. Many machines can never show anything but 0 for DirectMap1G,
so suppress that line unless direct_gbpages are really enabled.
3. The unit in /proc/meminfo is kB not number of pages: HugePages
messed that up, but they're an example to regret not to follow.
4. Once we use kB, it's easy to see that 1GB has gone missing (which
explains why CONFIG_CPA_DEBUG=y soon wraps DirectMap2M negative):
because head_64.S's level2_ident_pgt entries were not counted.
My fix is not ideal, but works for more and for less than 1G,
and avoids interfering with early bootup pagetable contortions.
x86: fix readb() et al compile error with gcc-3.2.3
Building 2.6.27-rc1 on x86 with gcc-3.2.3 fails with:
In file included from include/asm/dma.h:12,
from include/linux/bootmem.h:8,
from init/main.c:26:
include/asm/io.h: In function `readb':
include/asm/io.h:32: syntax error before string constant
include/asm/io.h: In function `readw':
include/asm/io.h:33: syntax error before string constant
include/asm/io.h: In function `readl':
include/asm/io.h:34: syntax error before string constant
include/asm/io.h: In function `__readb':
include/asm/io.h:36: syntax error before string constant
include/asm/io.h: In function `__readw':
include/asm/io.h:37: syntax error before string constant
include/asm/io.h: In function `__readl':
include/asm/io.h:38: syntax error before string constant
make[1]: *** [init/main.o] Error 1
make: *** [init] Error 2
Starting with 2.6.27-rc1 readb() et al are generated by a
build_mmio_read() macro, which generates asm() statements with
output register constraints like "=" "q", i.e. as two adjacent
string literals. This doesn't work with gcc-3.2.3.
Fixed by moving the "=" part into the callers' reg parameter
(as suggested by Ingo).
Build and boot-tested with gcc-3.2.3 on 32 and 64-bit x86.
Mark Langsdorf [Thu, 14 Aug 2008 14:11:26 +0000 (09:11 -0500)]
x86: invalidate caches before going into suspend
When a CPU core is shut down, all of its caches need to be flushed
to prevent stale data from causing errors if the core is resumed.
Current Linux suspend code performs an assignment after the flush,
which can add dirty data back to the cache. Â On some AMD platforms,
additional speculative reads have caused crashes on resume because
of this dirty data.
Relocate the cache flush to be the very last thing done before
halting. Â Tie into an assembly line so the compile will not
reorder it. Â Add some documentation explaining what is going
on and why we're doing this.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Acked-by: Mark Borden <mark.borden@amd.com> Acked-by: Michael Hohmuth <michael.hohmuth@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Aristeu Rozanski [Thu, 14 Aug 2008 20:32:15 +0000 (16:32 -0400)]
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
Currently, setup_p4_watchdog() use CCCR_OVF_PMI1 to enable the counter
overflow interrupts to the second logical core. But this bit doesn't work
on Pentium 4 Ds (model 4, stepping 4) and this patch avoids its use on
these processors. Tested on 4 different machines that have this
specific model with success.
Joerg Roedel [Thu, 14 Aug 2008 17:55:18 +0000 (19:55 +0200)]
x86, AMD IOMMU: initialize dma_ops after sysfs registration
If sysfs registration fails all memory used by IOMMU is freed. This
happens after dma_ops initialization and the functions will access the
freed memory then.
Fix this by initializing dma_ops after the sysfs registration.
Dave Jones [Thu, 14 Aug 2008 19:07:03 +0000 (15:07 -0400)]
x86: silence mmconfig printk
There's so much broken mmconfig hardware/bios'es out there,
that classing this as an error seems a little extreme.
Lower its priority to KERN_INFO so that it isn't so noisy
when booting with 'quiet'
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Darrick J. Wong [Thu, 14 Aug 2008 22:43:33 +0000 (15:43 -0700)]
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
msr_open tests for someone trying to open a device for a nonexistent CPU.
However, the function always returns 0, not ret like it should, hence
userspace can BUG the kernel trivially. This bug was introduced by the
cdev lock_kernel pushdown patch last May.
The BUG can be reproduced with these commands:
# mknod fubar c 202 8 <-- pick a number less than NR_CPUS that is not
the number of an online CPU
# cat fubar
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Zhao Yakui [Mon, 11 Aug 2008 02:33:31 +0000 (10:33 +0800)]
ACPI: Avoid bogus EC timeout when EC is in Polling mode
When EC is in Polling mode, OS will check the EC status continually by using
the following source code:
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
while (time_before(jiffies, delay)) {
if (acpi_ec_check_status(ec, event))
return 0;
msleep(1);
}
But msleep is realized by the function of schedule_timeout. At the same time
although one process is already waken up by some events, it won't be scheduled
immediately. So maybe there exists the following phenomena:
a. The current jiffies is already after the predefined jiffies.
But before timeout happens, OS has no chance to check the EC
status again.
b. If preemptible schedule is enabled, maybe preempt schedule will happen
before checking loop. When the process is resumed again, maybe
timeout already happens, which means that OS has no chance to check
the EC status.
In such case maybe EC status is already what OS expects when timeout happens.
But OS has no chance to check the EC status and regards it as AE_TIME.
So it will be more appropriate that OS will try to check the EC status again
when timeout happens. If the EC status is what we expect, it won't be regarded
as timeout. Only when the EC status is not what we expect, it will be regarded
as timeout, which means that EC controller can't give a response in time.
Zhao Yakui [Tue, 12 Aug 2008 02:40:10 +0000 (10:40 +0800)]
ACPI : Add the EC dmi table to fix the incorrect ECDT table
On some ASUS laptops the ECDT gives the incorrect command/status & Data I/O
register address.
AK: it seems like the command/data addresses are exchanged.
In such case it will cause that EC device can't be
initialized correctly.
To add the EC dmi table is to fix this issue. If the laptop falls into the
EC dmi table, the EC command/data I/O address will be fixed.
Holger Macht [Wed, 6 Aug 2008 15:56:01 +0000 (17:56 +0200)]
ACPI: Properly clear flags on false-positives and send uevent on sudden unplug
Some devices emit a ACPI_NOTIFY_DEVICE_CHECK while physically unplugging
even if the software undock has already been done and dock_present() check
fails. However, the internal flags need to be cleared (complete_undock()).
Also, even notify userspace if the dock station suddently went away
without proper software undocking.
Carlos Corbacho [Wed, 6 Aug 2008 18:13:56 +0000 (19:13 +0100)]
acer-wmi: Fix wireless and bluetooth on early AMW0 v2 laptops
In the old acer_acpi, I discovered that on some of the newer AMW0 laptops
that supported the WMID methods, they don't work properly for setting the
wireless and bluetooth values.
So for the AMW0 V2 laptops, we want to use both the 'old' AMW0 and the
'new' WMID methods for setting wireless & bluetooth to guarantee we always
enable it.
This was fixed in acer_acpi some time ago, but I forgot to port the patch
over to acer-wmi when it was merged.
(Without this patch, early AMW0 V2 laptops such as the Aspire 5040 won't
work with acer-wmi, where-as they did with the old acer_acpi).
AK: fix compilation
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> CC: stable@kernel.org Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Mon, 4 Aug 2008 03:13:01 +0000 (11:13 +0800)]
ACPICA: Additional error checking for pathname utilities
Add error check after all calls to acpi_ns_get_pathname_length.
Add status return from acpi_ns_build_external_path and check after
all calls. Add parameter validation to acpi_ut_initialize_buffer.
Reported by and initial patch by Ingo Molnar.
http://lkml.org/lkml/2008/7/21/176
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Fri, 4 Jul 2008 02:41:41 +0000 (10:41 +0800)]
ACPICA: Fix memory leak when deleting thermal/processor objects
Fixes a possible memory leak when thermal and processor objects
are deleted. Any associated notify handlers (and objects) were
not being deleted. Fiodor Suietov. BZ 506
Signed-off-by: Fiodor Suietov <fiodor.f.suietov@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Peter Zijlstra [Thu, 14 Aug 2008 13:49:00 +0000 (15:49 +0200)]
sched: fix rt-bandwidth hotplug race
When we hot-unplug a cpu and rebuild the sched-domain, all cpus will be
detatched. Alex observed the case where a runqueue was stealing bandwidth
from an already disabled runqueue to satisfy its own needs.
Stop this by skipping over already disabled runqueues.
Reported-by: Alex Nixon <alex.nixon@citrix.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Tested-by: Alex Nixon <alex.nixon@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Howells [Thu, 14 Aug 2008 10:37:28 +0000 (11:37 +0100)]
security: Fix setting of PF_SUPERPRIV by __capable()
Fix the setting of PF_SUPERPRIV by __capable() as it could corrupt the flags
the target process if that is not the current process and it is trying to
change its own flags in a different way at the same time.
__capable() is using neither atomic ops nor locking to protect t->flags. This
patch removes __capable() and introduces has_capability() that doesn't set
PF_SUPERPRIV on the process being queried.
This patch further splits security_ptrace() in two:
(1) security_ptrace_may_access(). This passes judgement on whether one
process may access another only (PTRACE_MODE_ATTACH for ptrace() and
PTRACE_MODE_READ for /proc), and takes a pointer to the child process.
current is the parent.
(2) security_ptrace_traceme(). This passes judgement on PTRACE_TRACEME only,
and takes only a pointer to the parent process. current is the child.
In Smack and commoncap, this uses has_capability() to determine whether
the parent will be permitted to use PTRACE_ATTACH if normal checks fail.
This does not set PF_SUPERPRIV.
Two of the instances of __capable() actually only act on current, and so have
been changed to calls to capable().
Of the places that were using __capable():
(1) The OOM killer calls __capable() thrice when weighing the killability of a
process. All of these now use has_capability().
(2) cap_ptrace() and smack_ptrace() were using __capable() to check to see
whether the parent was allowed to trace any process. As mentioned above,
these have been split. For PTRACE_ATTACH and /proc, capable() is now
used, and for PTRACE_TRACEME, has_capability() is used.
(3) cap_safe_nice() only ever saw current, so now uses capable().
(4) smack_setprocattr() rejected accesses to tasks other than current just
after calling __capable(), so the order of these two tests have been
switched and capable() is used instead.
(5) In smack_file_send_sigiotask(), we need to allow privileged processes to
receive SIGIO on files they're manipulating.
(6) In smack_task_wait(), we let a process wait for a privileged process,
whether or not the process doing the waiting is privileged.
I've tested this with the LTP SELinux and syscalls testscripts.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: James Morris <jmorris@namei.org>
Thomas Gleixner [Thu, 14 Aug 2008 10:17:06 +0000 (12:17 +0200)]
x86: hpet: workaround SB700 BIOS
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Artem Bityutskiy [Tue, 12 Aug 2008 13:30:12 +0000 (16:30 +0300)]
UBIFS: xattr bugfixes
Xattr code has not been tested for a while and there were
serveral bugs. One of them is using wrong inode in
'ubifs_jnl_change_xattr()'. The other is a deadlock in
'ubifs_setxattr()': the i_mutex is locked in
'cap_inode_need_killpriv()' path, so deadlock happens when
'ubifs_setxattr()' tries to lock it again.
Yinghai Lu [Thu, 14 Aug 2008 09:16:30 +0000 (02:16 -0700)]
x86: check bigsmp in smp_sanity_check instead of cpu_up
clear bits for cpu nr > 8.
This allows us to boot the full range of possible CPUs that the
supported APIC model will allow. Previously we'd hang or boot up
with less than 8 CPUs.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Max Krasnyansky [Mon, 11 Aug 2008 21:55:31 +0000 (14:55 -0700)]
x86: resurrect proper handling of maxcpus= kernel option (v2)
For some reason we had two parsers registered for maxcpus=. One in init/main.c
and another in arch/x86/smpboot.c. So I nuked the one in arch/x86.
Also 64-bit kernels used to handle maxcpus= as documented in
Documentation/cpu-hotplug.txt. CPUs with 'id > maxcpus' are initialized
but not booted. 32-bit version for some reason ignored them even though
all the infrastructure for booting them later is there.
In the current mainline both 64 and 32 bit versions are broken.
This patch restores the correct behaviour. I've tested x86_64 version on
4- and 8- way Core2 and 2-way Opteron based machines. Various config
combinations SMP, !SMP, CPU_HOTPLUG, !CPU_HOTPLUG.
Booted with maxcpus=1 and maxcpus=4, etc. Everything is working as expected.
So far we've received two reports from different people confirming that 32-bit
version also works fine, both on dual core laptops and 16way server machines.
[v2: This version fixes visws breakage pointed out by Ingo.]
Zhang, Yanmin [Wed, 14 Aug 2030 07:56:40 +0000 (15:56 +0800)]
sched: fix the race between walk_tg_tree and sched_create_group
With 2.6.27-rc3, I hit a kernel panic when running volanoMark on my
new x86_64 machine. I also hit it with other 2.6.27-rc kernels.
See below log.
Basically, function walk_tg_tree and sched_create_group have a race
between accessing and initiating tg->children. Below patch fixes it
by moving tg->children initiation to the front of linking tg->siblings
to parent->children.
David S. Miller [Thu, 14 Aug 2008 08:45:41 +0000 (01:45 -0700)]
sparc64: Fix cmdline_memory_size handling bugs.
First, lmb_enforce_memory_limit() interprets it's argument
(mostly, heh) as a size limit not an address limit. So pass
the raw cmdline_memory_size value into it. And we don't
need to check it against zero, lmb_enforce_memory_limit() does
that for us.
Next, free_initmem() needs special handling when the kernel
command line trims the available memory. The problem case is
if the trimmed out memory is where the kernel image itself
resides.
When that memory is trimmed out, we don't add those physical
ram areas to the sparsemem active ranges, amongst other things.
Which means that this free_initmem() code will free up invalid
page structs, resulting in either crashes or hangs.
Just quick fix this by not freeing initmem at all if "mem="
was given on the boot command line.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger [Thu, 14 Aug 2008 06:29:57 +0000 (14:29 +0800)]
Blackfin arch: cleanup cache lock code
- remove cheesy read_iloc() function
- move invalidate_entire_icache function to lock.S
- export proper prototypes for functions in lock.S
- only build lock.S when BFIN_ICACHE_LOCK is enabled
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
usb: musb: pass configuration specifics via pdata
usb: musb: fix hanging when rmmod gadget driver
USB: Add MUSB and TUSB support
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
USB: Add vendor/product id of ZTE MF628 to option
USB: quirk PLL power down mode
USB: omap_udc: fix compilation with debug enabled
usb: cdc-acm: drain writes on close
usb: cdc-acm: stop dropping tx buffers
usb: cdc-acm: bugfix release()
usb gadget: issue notifications from ACM function
usb gadget: remove needless struct members
USB: sh: r8a66597-hcd: fix disconnect regression
USB: isp1301: fix compilation
USB: fix compiler warning fix
usb-storage: unusual_devs entry for Nokia 5300
USB: cdc-acm.c: Fix compile warnings
USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
usb: isp1760: don't be noisy about short packets.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
netns: Fix crash by making igmp per namespace
bnx2x: Version update
bnx2x: Checkpatch compliance
bnx2x: Spelling mistakes
bnx2x: Minor code improvements
bnx2x: Driver info
bnx2x: 1G LED does not turn off
bnx2x: 8073 PHY changes
bnx2x: Change GPIO for any port
bnx2x: Pause settings
bnx2x: Link order with external PHY
bnx2x: No LRO without Rx checksum
bnx2x: Wrong structure size
bnx2x: WoL capability
bnx2x: Clearing MAC addresses filters
bnx2x: Delay in while loops
bnx2x: PBA Table Page Alignment Workaround
bnx2x: Self-test false positive
bnx2x: Memory allocation
bnx2x: HW attention lock
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Felipe Balbi [Mon, 4 Aug 2008 10:53:52 +0000 (13:53 +0300)]
usb: musb: fix hanging when rmmod gadget driver
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Oliver Martin [Sat, 9 Aug 2008 02:49:26 +0000 (04:49 +0200)]
USB: Add vendor/product id of ZTE MF628 to option
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Libin Yang [Fri, 8 Aug 2008 07:03:31 +0000 (15:03 +0800)]
USB: quirk PLL power down mode
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:46:10 +0000 (18:46 -0700)]
usb: cdc-acm: drain writes on close
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:44:12 +0000 (18:44 -0700)]
usb: cdc-acm: stop dropping tx buffers
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Engraf <david.engraf@netcom.eu> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:49:57 +0000 (18:49 -0700)]
usb gadget: issue notifications from ACM function
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 7 Aug 2008 17:02:40 +0000 (13:02 -0400)]
usb-storage: unusual_devs entry for Nokia 5300
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.