Boaz Harrosh [Tue, 5 Dec 2006 09:19:14 +0000 (10:19 +0100)]
[PATCH] remove blk_queue_activity_fn
While working on bidi support at struct request level
I have found that blk_queue_activity_fn is actually never used.
The only user is in ide-probe.c with this code:
/* enable led activity for disk drives only */
if (drive->media == ide_disk && hwif->led_act)
blk_queue_activity_fn(q, hwif->led_act, drive);
And led_act is never initialized anywhere.
(Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18)
Unless it is all for future use off course.
(this patch is against linux-2.6-block.git as off 2006/12/4)
Linus Torvalds [Tue, 12 Dec 2006 02:28:59 +0000 (18:28 -0800)]
Merge branch 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Add missing #include <linux/param.h> to delay.c
[AVR32] Pass dev parameter to dma_cache_sync()
[AVR32] Implement intc_get_pending()
[AVR32] Don't include <asm/delay.h>
[AVR32] Put the chip in "stop" mode when halting the system
[AVR32] Set flow handler for external interrupts
[AVR32] Remove unused file
[AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data
[AVR32] Move ethernet tag parsing to board-specific code
[AVR32] Add macb1 platform_device
[AVR32] Portmux API update
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
Ralf Baechle [Mon, 11 Dec 2006 11:54:52 +0000 (11:54 +0000)]
[MIPS] Discard .exit.text and .exit.data at runtime.
While the recent cset 86384d544157db23879064cde36061cdcafc6794 did improve
things it didn't resolve all the problems. So bite the bullet and discard
.exit.text and .exit.data at runtime. Which of course sucks because it
bloats binaries with code that will never ever be used but it's the only
thing that will work reliable as demonstrated by the function sd_major() in
drivers/scsi/sd.c.
Gcc may compile sd_major() using a jump table which it will put into
.rodata. If it also inlines sd_major's function body into exit_sd() which
gcc > 3.4.x does. If CONFIG_BLK_DEV_SD has been set to y we would like ld
to discard exit_sd's code at link time. However sd_major happens to
contain a switch statement which gcc will compile using a jump table in
.rodata on the architectures I checked. So, when ld later discards
.exit.text only the jump table in .rodata with its stale references to
the discard .exit.text will be left which any no antique ld will honor
with a link error.
Andrew Morton [Tue, 12 Dec 2006 01:24:46 +0000 (17:24 -0800)]
[NETPOLL]: Fix local_bh_enable() warning.
During boot we get:
netconsole: device eth0 not up yet, forcing it
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
WARNING (!__warned) at kernel/softirq.c:137 local_bh_enable()
Normally networking isn't invoked with interrupts turned off, but I
suppose we don't have a choice here. This is unique being a place where you
can get called with BH on, off, or IRQs off.
Given that this is only used for printk, the easiest solution is probably
just to disable local IRQs instead of BH.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Mon, 11 Dec 2006 06:35:24 +0000 (22:35 -0800)]
[IPVS]: Use msleep_interruptable() instead of ssleep() aka msleep()
Dean Manners notices that when an IPVS synchonisation daemons are
started the system load slowly climbs up to 1. This seems to be related
to the call to ssleep(1) (aka msleep(1000) in the main loop. Replacing
this with a call to msleep_interruptable() seems to make the problem go
away. Though I'm not sure that it is correct.
This is the second edition of this patch, which replaces ssleep()
in the main loop for both the master and backup threads, as well
as some thread synchronisation code. The latter is just for thorougness
as it shouldn't be causing any problems.
Signed-Off-By: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[DCCP] ccid3: Fixup some type conversions related to rtts
Spotted by David Miller when compiling on sparc64, I reproduced it here on
parisc64, that are the only platforms to define __kernel_suseconds_t as an
'int', all the others, x86_64 and x86 included typedef it as a 'long', but from
the definition of suseconds_t it should just be an 'int' on platforms where it
is >= 32bits, it would not require all the castings from suseconds_t to (int)
when printking variables of this type, that are not needed on parisc64 and
sparc64.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:24:57 +0000 (00:24 -0200)]
[DCCP] ccid3: BUG-FIX - conversion errors
This fixes conversion errors which arose by not properly type-casting
from u32 to __u64. Fixed by explicitly casting each type which is not
__u64, or by performing operation after assignment.
The patch further adds missing debug information to track the current
value of X_recv.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:24:11 +0000 (00:24 -0200)]
[DCCP] ccid3: Reorder packet history header file
No code change at all.
To make the header file easier to read, the following ordering is established
among the declarations:
* hist_new
* hist_delete
* hist_entry_new
* hist_head
* hist_find_entry
* hist_add_entry
* hist_entry_delete
* hist_purge
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:09:21 +0000 (00:09 -0200)]
[DCCP] ccid3: Perform history operations only after packet has been sent
This migrates all packet history operations into the routine
ccid3_hc_tx_packet_sent, thereby removing synchronization problems
that occur when, as before, the operations are spread over multiple
routines.
The following minor simplifications are also applied:
* several simplifications now follow from this change - several tests
are now no longer required
* removal of one unnecessary variable (dp)
Justification:
Currently packet history operations span two different routines,
one of which is likely to pass through several iterations of sleeping
and awakening.
The first routine, ccid3_hc_tx_send_packet, allocates an entry and
sets a few fields. The remaining fields are filled in when the second
routine (which is not within a sleeping context), ccid3_hc_tx_packet_sent,
is called. This has several strong drawbacks:
* it is not necessary to split history operations - all fields can be
filled in by the second routine
* the first routine is called multiple times, until a packet can be sent,
and sleeps meanwhile - this causes a lot of difficulties with regard to
keeping the list consistent
* since both routines do not have a producer-consumer like synchronization,
it is very difficult to maintain data across calls to these routines
* the fact that the routines are called in different contexts (sleeping, not
sleeping) adds further problems
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:07:37 +0000 (00:07 -0200)]
[DCCP] ccid3: Shift window counter computation
This puts the window counter computation [RFC 4342, 8.1] into a separate
function which is called whenever a new packet is ready for immediate
transmission in ccid3_hc_tx_send_packet.
Justification:
The window counter update was previously computed after the packet was sent. This has
two drawbacks, both fixed by this patch:
1) re-compute another timestamp almost directly after the packet was sent (expensive),
2) the CCVal for the window counter is needed at the instant the packet is sent.
Further details:
The initialisation of the window counter is left in the state NO_SENT, as before.
The algorithm will do nothing if either RTT is initialised to 0 (which is ok) or if
the RTT value remains below 4 microseconds (which is almost pathological).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:06:32 +0000 (00:06 -0200)]
[DCCP] ccid3: Sanity-check RTT samples
CCID3 performance depends much on the accuracy of RTT samples. If RTT
samples grow too large, performance can be catastrophically poor.
To limit the amount of possible damage in such cases, the patch
* introduces an upper limit which identifies a maximum `sane' RTT value;
* uses a macro to enforce this upper limit.
Using a macro was given preference, since it is necessary to identify the
calling function in the warning message. Since exceeding this threshold
identifies a critical condition, DCCP_CRIT is used and not DCCP_WARN.
Many thanks to Ian McDonald for collaboration on this issue.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:06:01 +0000 (00:06 -0200)]
[DCCP] ccid3: Initialise RTT values
In both the sender and the receiver it is possible that the stored
RTT value is accessed before an actual RTT estimate has been computed.
This patch
* initialises the sender RTT to 0
- the sender always accesses the RTT in ccid3_hc_tx_packet_sent
- the RTT is further needed for the window counter algorithm
* replaces the receiver initialisation of 5msec with 0
- which has the same effect and removes an `XXX'
- the RTT value is needed in ccid3_hc_rx_packet_recv as rtt_prev
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
is already performed _unconditionally_ in ccid3_hc_tx_send_packet.
Since there is further no current need for this function, it is removed
entirely. Since furthermore, there is actually no present need for the
entire interface function ccid_hc_tx_insert_options, it was decided to
remove it also, to clean up the interface.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:05:12 +0000 (00:05 -0200)]
[DCCP]: Warn when discarding packet due to internal errors
This adds a (debug) warning message which is triggered whenever a packet is
discarded due to send failure.
It also adds a conditional, so that an interruption during dccp_wait_for_ccid
is not treated as a `BUG': the rationale is that interruptions are external,
whereas bug warnings are concerned with the internals.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:04:43 +0000 (00:04 -0200)]
[DCCP]: Only deliver to the CCID rx side in charge
This is an optimisation to reduce CPU load. The received feedback is now
only directed to the active CCID component, without requiring processing
also by the inactive one.
As a consequence, a similar test in ccid3.c is now redundant and is
also removed.
Justification:
Currently DCCP works as a unidirectional service, i.e. a listening server
is not at the same time a connecting client.
As far as I can see, several modifications are necessary until that
becomes possible.
At the present time, received feedback is both fed to the rx/tx CCID
modules. In unidirectional service, only one of these is active at any
one time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:04:16 +0000 (00:04 -0200)]
[DCCP]: Simplify TFRC calculation
In migrating towards using the newer functions scaled_div/scaled_div32
for TFRC computations mapped from floating-point onto integer arithmetic,
this completes the last stage of modifications.
In particular, the overflow case for computing X_calc is circumvented by
* breaking the computation into two stages
* the first stage, res = (s*1E6)/R, cannot overflow due to use of u64
* in the second stage, res = (res*1E6)/f, overflow on u32 is avoided due
to (i) returning UINT_MAX in this case (which is logically appropriate)
and (ii) issuing a warning message into the system log (since very likely
there is a problem somewhere else with the parameters)
Lastly, all such scaling operations are now exported into tfrc.h, since
actually this form of scaled computation is specific to TFRC and not to CCID3.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:03:51 +0000 (00:03 -0200)]
[DCCP]: Debug timeval operations
Problem:
Most target types in the CCID3 code are u32, so subtle conversion errors
can occur if signed time calculations yield negative results: the original
values are lost in the conversion to unsigned, calculation errors go undetected.
This patch therefore
* sets all critical time types from unsigned to suseconds_t
* avoids comparison between signed/unsigned via type-casting
* provides ample warning messages in case time calculations are negative
These warning messages can be removed at a later stage when the code
has undergone more testing.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:03:30 +0000 (00:03 -0200)]
[DCCP] ccid3: Simplify calculation for reverse lookup of p
This simplifies the calculation of a value p for a given fval when the
first loss interval is computed (RFC 3448, 6.3.1). It makes use of the
two new functions scaled_div/scaled_div32 to provide overflow protection.
Additionally, protection against divide-by-zero is extended - in this
case the function will return the maximally possible value of p=100%.
Background:
The maximum fval, f(100%), is approximately 244, i.e. the scaled value of fval
should never exceed 244E6, which fits easily into u32. The problem is the scaling
by 10^6, since additionally R(TT) is in microseconds.
This is resolved by breaking the division into two stages: the first stage
computes fval=(s*10^6)/R, stores that into u64; the second stage computes
fval = (fval*10^6)/X_recv and complains if overflow is reached for u32.
This case is safe since the TFRC reverse-lookup routine then returns p=100%.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:02:12 +0000 (00:02 -0200)]
[DCCP] ccid3: Finer-grained resolution of sending rates
This patch
* resolves a bug where packets smaller than 32/64 bytes resulted in sending rates of 0
* supports all sending rates from 1/64 bytes/second up to 4Gbyte/second
* simplifies the present overflow problems in calculations
Current sending rate X and the cached value X_recv of the receiver-estimated
sending rate are both scaled by 64 (2^6) in order to
* cope with low sending rates (minimally 1 byte/second)
* allow upgrading to use a packets-per-second implementation of CCID 3
* avoid calculation errors due to integer arithmetic cut-off
The patch implements a revised strategy from
http://www.mail-archive.com/dccp@vger.kernel.org/msg01040.html
The only difference with regard to that strategy is that t_ipi is already
used in the calculation of the nofeedback timeout, which saves one division.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:01:22 +0000 (00:01 -0200)]
[DCCP] ccid3: Fix two bugs in sending rate computation
This fixes
1) a bug in the recomputation of the sending rate by the nofeedback
timer when no feedback at all has so far been sent by the receiver:
min_t was used instead of max_t, which is wrong (cf. RFC 3448, p. 10);
2) an error in the computation of larger initial windows: instead of
min(... max()) (cf. RFC 4342, 5.), the code had used max(... max()).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 02:00:14 +0000 (00:00 -0200)]
[DCCP] ccid3: Two optimisations for sending rate recomputation
This performs two optimisations for the recomputation of the sending rate.
1) Currently the target sending rate X_calc is recalculated whenever
a) the nofeedback timer expires, or
b) a feedback packet is received.
In the (a) case, recomputing X_calc is redundant, since
* the parameters p and RTT do not change in between the
reception of feedback packets;
* the parameter X_recv is either modified from received
feedback or via the nofeedback timer;
* a test (`p == 0') in the nofeedback timer avoids using
a stale/undefined value of X_calc if p was previously 0.
2) The nofeedback timer now only recomputes a timestamp when p == 0.
This is according to step (4) of [RFC 3448, 4.3] and avoids
unnecessarily determining a timestamp.
A debug statement about not updating X is also removed - it helps very
little in debugging and just clutters the logs.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Gerrit Renker [Sun, 10 Dec 2006 01:59:14 +0000 (23:59 -0200)]
[DCCP] ccid3: Check against too large p
This patch follows a suggestion by Ian McDonald and ensures that in
the current code the value of p can not exceed 100%. Such a value is
illegal and would consequently cause a bug condition in tfrc_calc_x().
The receiver case is also tested, and a warning message is added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Ian McDonald [Sun, 10 Dec 2006 01:56:09 +0000 (23:56 -0200)]
[DCCP]: Remove timeo from output.c
It simplifies waiting for the CCID module to signal that a packet
is ready to be sent. Other simplifications flow on from this such as
removing constants.
As a result of this EAGAIN is not returned any more by dccp_wait_for_ccid
(which would otherwise lead to unnecessarily discarding the packet in
dccp_write_xmit).
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Randy Dunlap [Sat, 9 Dec 2006 21:58:42 +0000 (13:58 -0800)]
[NET]: Fix WAN routers kconfig dependency.
Currently WAN router drivers can be built in-kernel while the
register/unregister_wan_device interfaces are built as modules.
This causes:
drivers/built-in.o: In function `cycx_init':
cycx_main.c:(.init.text+0x5c4b): undefined reference to `register_wan_device'
drivers/built-in.o: In function `cycx_exit':
cycx_main.c:(.exit.text+0x560): undefined reference to `unregister_wan_device'
make: *** [.tmp_vmlinux1] Error 1
The problem is caused by tristate -> bool conversion (y or m => y),
so convert WAN_ROUTER_DRIVERS to a tristate so that the correct
dependency is preserved.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 11 Dec 2006 20:12:04 +0000 (12:12 -0800)]
Make sure we populate the initroot filesystem late enough
We should not initialize rootfs before all the core initializers have
run. So do it as a separate stage just before starting the regular
driver initializers.
Linus Torvalds [Mon, 11 Dec 2006 17:28:46 +0000 (09:28 -0800)]
Make SLES9 "get_kernel_version" work on the kernel binary again
As reported by Andy Whitcroft, at least the SLES9 initrd build process
depends on getting the kernel version from the kernel binary. It does
that by simply trawling the binary and looking for the signature of the
"linux_banner" string (the string "Linux version " to be exact. Which
is really broken in itself, but whatever..)
That got broken when the string was changed to allow /proc/version to
change the UTS release information dynamically, and "get_kernel_version"
thus returned "%s" (see commit a2ee8649ba6d71416712e798276bf7c40b64e6e5:
"[PATCH] Fix linux banner utsname information").
This just restores "linux_banner" as a static string, which should fix
the version finding. And /proc/version simply uses a different string.
To avoid wasting even that miniscule amount of memory, the early boot
string should really be marked __initdata, but that just causes the same
bug in SLES9 to re-appear, since it will then find other occurrences of
"Linux version " first.
Cc: Andy Whitcroft <apw@shadowen.org> Acked-by: Herbert Poetzl <herbert@13thfloor.at> Cc: Andi Kleen <ak@suse.de> Cc: Andrew Morton <akpm@osdl.org> Cc: Steve Fox <drfickle@us.ibm.com> Acked-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brice Goglin [Mon, 11 Dec 2006 10:27:19 +0000 (11:27 +0100)]
[PATCH] myri10ge: fix big_bytes in case of vlan frames
Fix sizing of big_bytes in the case of vlan frames. The 4
VLAN_HLEN bytes were omitted, leading to sizing the big buffer
4 bytes smaller than it should be. Due to how rx buffers are
carved from pages, this was harmless for the common (9000, 1500)
byte MTUs, but could lead to data corruption for some MTUs.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brice Goglin [Mon, 11 Dec 2006 10:26:12 +0000 (11:26 +0100)]
[PATCH] myri10ge: drop contiguous skb routines
Drop the old routines that used the physically contigous skb now
that we use the physical pages. And rename myri10ge_page_rx_done()
to myri10ge_rx_done() as it was previously.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since macb is a chip-internal device, use __raw_readl and
__raw_writel instead of readl/writel. This will perform native-endian
accesses, which is the right thing to do on both AVR32 and ARM devices.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] MACB: Use struct delayed_work instead of struct work_struct
The macb driver calls schedule_delayed_work() and friends, so we need
to use a struct delayed_work along with it. The conversion was
explained by David Howells on lkml Dec 5 2006:
http://lkml.org/lkml/2006/12/5/269
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Victor [Mon, 11 Dec 2006 11:40:23 +0000 (12:40 +0100)]
AT91 MMC update for 2.6.19
The driver is usable on the newer SAM9 processors so replace all text
references to AT91RM9200 with just AT91.
The controller bug where all the words are byte-swapped is fixed on the
AT91SAM9 processors. The byte-swapping work-around therefore only needs
to be done if cpu_is_at91rm9200().
[Original patch from Wojtek Kaniewski]
The AT91RM9200 and AT91SAM9260 processors support two MMC/SD slots - the
slot which is connected is now passed via the platform_data and the
correct slot selected in the AT91_MCI_SDCR register.
The driver should not be calling at91_set_gpio_output() since the VCC
pin should have already been configured as an output in the
processor/board setup code. The driver should call
at91_set_gpio_value().
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pierre Ossman [Thu, 7 Dec 2006 18:17:20 +0000 (19:17 +0100)]
mmc: Change SDHCI iomem error to a warning
Some controllers report an invalid iomem size, but seem to work
correctly anyway. Change our current error to just a warning and
hope it doesn't cause too much problems.
Andrew Victor [Mon, 23 Oct 2006 12:50:09 +0000 (14:50 +0200)]
AT91 MMC 4 : Interrupt handler cleanup
This patch simplifies the AT91RM9200 MMC interrupt handler code so that
it doesn't re-read the Interrupt Status and Interrupt Mask registers
multiple times.
Also defined AT91_MCI_ERRORS instead of using the hard-coded 0xffff0000.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This makes powerpc use the generic BUG machinery. The biggest reports the
function name, since it is redundant with kallsyms, and not needed in general.
There is an overall reduction of code, since module_32/64 duplicated several
functions.
Unfortunately there's no way to tell gcc that BUG won't return, so the BUG
macro includes a goto loop. This will generate a real jmp instruction, which
is never used.
[akpm@osdl.org: build fix]
[paulus@samba.org: remove infinite loop in BUG_ON] Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Andi Kleen <ak@muc.de> Cc: Hugh Dickens <hugh@veritas.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Mon, 11 Dec 2006 05:15:47 +0000 (23:15 -0600)]
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
On 85xx we don't build in dcr support because the core doesn't implement the
instructions. This caused problems when building an 85xx kernel. Additionally
made it so we only build __mtdcr/__mfdcr if we are CONFIG_PPC_DCR_NATIVE.
The 85xx build issue wasPointed out by Dai Haruki.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
[POWERPC] Fix irq routing on some 32-bit PowerMacs
The changes to use pci_read_irq_line() broke interrupt parsing
on some 32-bit powermacs (oops). The reason is a bit obscure.
The code to parse interrupts happens earlier now, during
pcibios_fixup() as the PCI bus is being probed. However, the
current implementation pci_device_to_OF_node() for 32-bit
powerpc relies, on machines like PowerMac which renumber PCI buses,
on a table called pci_OF_bus_map containing a map of bus numbers
between the kernel and the firmware which is setup only later.
Thus, it fails to match the device node. In addition, some of
Apple internal PCI devices lack a proper PCI_INTERRUPT_PIN, thus
preventing the fallback mapping code to work.
This patch fixes it by making pci_device_to_OF_node() 32-bit
implementation use a different algorithm that works without
using the pci_OF_bus_map thing (which I intend to deprecate
anyway). It's a bit slower but that function isn't called in
any hot path hopefully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Wed, 29 Nov 2006 11:27:42 +0000 (22:27 +1100)]
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
For PAPR partitions with large amounts of memory, the firmware has an
alternative, more compact representation for the information about the
memory in the partition and its NUMA associativity information. This
adds the code to the kernel to parse this alternative representation.
The other part of this patch is telling the firmware that we can
handle the alternative representation. There is however a subtlety
here, because the firmware will invoke a reboot if the memory
representation we request is different from the representation that
firmware is currently using. This is because firmware can't change
the representation on the fly. Further, some firmware versions used
on POWER5+ machines have a bug where this reboot leaves the machine
with an altered value of load-base, which will prevent any kernel
booting until it is reset to the normal value (0x4000). Because of
this bug, we do NOT set fake_elf.rpanote.new_mem_def = 1, and thus we
do not request the new representation on POWER5+ and earlier machines.
We do request the new representation on POWER6, which uses the
ibm,client-architecture-support call.
Ralf Baechle [Sun, 10 Dec 2006 18:43:59 +0000 (18:43 +0000)]
[MIPS] Export local_flush_data_cache_page for sake of IDE.
On a CPU with aliases the IDE core needs to flush caches in the special
IDE variants of insw, insl etc. If IDE support is built as a module this
will only work if local_flush_data_cache_page happens is exported as a
module.
As per policy export local_flush_data_cache_page as GPL symbol only.
Linus Torvalds [Sun, 10 Dec 2006 17:59:18 +0000 (09:59 -0800)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (132 commits)
V4L/DVB 4949b: Fix container_of pointer retreival
V4L/DVB (4949a): Fix INIT_WORK
V4L/DVB (4949): Cxusb: codingstyle cleanups
V4L/DVB (4948): Cxusb: Convert tuner functions to use dvb_pll_attach
V4L/DVB (4947): Cx88: trivial cleanups
V4L/DVB (4946): Cx88: Move cx88_dvb_bus_ctrl out of the card-specific area
V4L/DVB (4945): Cx88: consolidate cx22702_config structs
V4L/DVB (4944): Cx88: Convert DViCO FusionHDTV Hybrid to use dvb_pll_attach
V4L/DVB (4943): Cx88: cleanup dvb_pll_attach for lgdt3302 tuners
V4L/DVB (4953): Usbvision minor fixes
V4L/DVB (4951): Add version.h, since it is required for VIDIOC_QUERYCAP
V4L/DVB (4940): Or51211: Changed SNR and signal strength calculations
V4L/DVB (4939): Or51132: Changed SNR and signal strength reporting
V4L/DVB (4938): Cx88: Convert lgdt3302 tuning function to use dvb_pll_attach
V4L/DVB (4941): Remove LINUX_VERSION_CODE and fix identations
V4L/DVB (4942): Whitespace cleanups
V4L/DVB (4937): Usbvision cleanup and code reorganization
V4L/DVB (4936): Make MT4049FM5 tuner to set FM Gain to Normal
V4L/DVB (4935): Added the capability of selecting fm gain by tuner
V4L/DVB (4934): Usbvision radio requires GainNormal at e register
...
The following patchset adds a driver for Intel's hardware virtualization
extensions to the x86 architecture. The driver adds a character device
(/dev/kvm) that exposes the virtualization capabilities to userspace. Using
this driver, a process can run a virtual machine (a "guest") in a fully
virtualized PC containing its own virtual hard disks, network adapters, and
display.
Using this driver, one can start multiple virtual machines on a host.
Each virtual machine is a process on the host; a virtual cpu is a thread in
that process. kill(1), nice(1), top(1) work as expected. In effect, the
driver adds a third execution mode to the existing two: we now have kernel
mode, user mode, and guest mode. Guest mode has its own address space mapping
guest physical memory (which is accessible to user mode by mmap()ing
/dev/kvm). Guest mode has no access to any I/O devices; any such access is
intercepted and directed to user mode for emulation.
The driver supports i386 and x86_64 hosts and guests. All combinations are
allowed except x86_64 guest on i386 host. For i386 guests and hosts, both pae
and non-pae paging modes are supported.
SMP hosts and UP guests are supported. At the moment only Intel
hardware is supported, but AMD virtualization support is being worked on.
Performance currently is non-stellar due to the naive implementation of the
mmu virtualization, which throws away most of the shadow page table entries
every context switch. We plan to address this in two ways:
- cache shadow page tables across tlb flushes
- wait until AMD and Intel release processors with nested page tables
Currently a virtual desktop is responsive but consumes a lot of CPU. Under
Windows I tried playing pinball and watching a few flash movies; with a recent
CPU one can hardly feel the virtualization. Linux/X is slower, probably due
to X being in a separate process.
In addition to the driver, you need a slightly modified qemu to provide I/O
device emulation and the BIOS.
Caveats (akpm: might no longer be true):
- The Windows install currently bluescreens due to a problem with the
virtual APIC. We are working on a fix. A temporary workaround is to
use an existing image or install through qemu
- Windows 64-bit does not work. That's also true for qemu, so it's
probably a problem with the device model.
[bero@arklinux.org: build fix]
[simon.kagstrom@bth.se: build fix, other fixes]
[uril@qumranet.com: KVM: Expose interrupt bitmap]
[akpm@osdl.org: i386 build fix]
[mingo@elte.hu: i386 fixes]
[rdreier@cisco.com: add log levels to all printks]
[randy.dunlap@oracle.com: Fix sparse NULL and C99 struct init warnings]
[anthony@codemonkey.ws: KVM: AMD SVM: 32-bit host support] Signed-off-by: Yaniv Kamay <yaniv@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Cc: Simon Kagstrom <simon.kagstrom@bth.se> Cc: Bernhard Rosenkraenzer <bero@arklinux.org> Signed-off-by: Uri Lublin <uril@qumranet.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Roland Dreier <rolandd@cisco.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Anthony Liguori <anthony@codemonkey.ws> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6-omap-h63xx.git / log