sata_promise: fix hardreset hotplug events, take 2
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.
This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.
The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)
This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().
Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.
Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sun, 23 Mar 2008 12:05:15 +0000 (21:05 +0900)]
libata: improve HPA error handling
There's no point in retrying and eventually failing device detection
when the device rejects READ_NATIVE_MAX[_EXT]. Disable HPA unlocking
if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is
rejected.
This allows some old drives to work even if they aren't blacklisted.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sun, 23 Mar 2008 06:16:53 +0000 (15:16 +0900)]
libata: assume no device is attached if both IDENTIFYs are aborted
This is to fix bugzilla #10254. QSI cdrom attached to pata_sis as
secondary master appears as phantom device for the slave.
Interestingly, instead of not setting DRQ after IDENTIFY which
triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which
makes EH retry.
Modify EH such that it assumes no device is attached if both flavors
of IDENTIFY are aborted by the device. There really isn't much point
in retrying when the device actively aborts the commands.
While at it, convert NODEV detection message to ata_dev_printk() to
help debugging obscure detection problems.
This problem was reported by Jan Bücken.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Jan Bücken <jb.faq@gmx.de> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Mon, 24 Mar 2008 20:09:34 +0000 (13:09 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix Oops with TQM5200 on TQM5200
[POWERPC] mpc5200: Fix null dereference if bestcomm fails to initialize
[POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver
[POWERPC] Fix crash in init_ipic_sysfs on efika
[POWERPC] Don't use 64k pages for ioremap on pSeries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: exec PT_DTRACE
[SPARC64]: Use shorter list_splice_init() for brevity.
[SPARC64]: Remove most limitations to kernel image size.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sch_htb: fix "too many events" situation
connector: convert to single-threaded workqueue
[ATM]: When proc_create() fails, do some error handling work and return -ENOMEM.
[SUNGEM]: Fix NAPI assertion failure.
BNX2X: prevent ethtool from setting port type
[9P] net/9p/trans_fd.c: remove unused variable
[IPV6] net/ipv6/ndisc.c: remove unused variable
[IPV4] fib_trie: fix warning from rcu_assign_poinger
[TCP]: Let skbs grow over a page on fast peers
[DLCI]: Fix tiny race between module unload and sock_ioctl.
[SCTP]: Fix build warnings with IPV6 disabled.
[IPV4]: Fix null dereference in ip_defrag
Roland Dreier [Mon, 24 Mar 2008 16:03:03 +0000 (12:03 -0400)]
SVCRDMA: Use only 1 RDMA read scatter entry for iWARP adapters
The iWARP protocol limits RDMA read requests to a single scatter
entry. NFS/RDMA has code in rdma_read_max_sge() that is supposed to
limit the sge_count for RDMA read requests to 1, but the code to do
that is inside an #ifdef RDMA_TRANSPORT_IWARP block. In the mainline
kernel at least, RDMA_TRANSPORT_IWARP is an enum and not a
preprocessor #define, so the #ifdef'ed code is never compiled.
In my test of a kernel build with -j8 on an NFS/RDMA mount, this
problem eventually leads to trouble starting with:
The trivial fix is to delete the #ifdef guard. The check seems to be
a remnant of when the NFS/RDMA code was not merged and needed to
compile against multiple kernel versions, although I don't think it
ever worked as intended. In any case now that the code is upstream
there's no need to test whether the RDMA_TRANSPORT_IWARP constant is
defined or not.
Without this patch, my kernel build on an NFS/RDMA mount using NetEffect
adapters quickly and 100% reproducibly failed with an error like:
ld: final link failed: Software caused connection abort
With the patch applied I was able to complete a kernel build on the
same setup.
(Tom Tucker says this is "actually an _ancient_ remnant when it had to
compile against iWARP vs. non-iWARP enabled OFA trees.")
Signed-off-by: Roland Dreier <rolandd@cisco.com> Acked-by: Tom Tucker <tom@opengridcomputing.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 24 Mar 2008 18:22:39 +0000 (11:22 -0700)]
x86-32: Pass the full resource data to ioremap()
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org> Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property. Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.
Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.
This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Sat, 22 Mar 2008 03:20:29 +0000 (14:20 +1100)]
[POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver
If the reg property is missing from the phy node (unlikely, but possible),
then the kernel will oops with a NULL pointer dereference. This fixes
it by checking the pointer first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Mon, 17 Mar 2008 19:53:05 +0000 (06:53 +1100)]
[POWERPC] Fix crash in init_ipic_sysfs on efika
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller. init_ipic_sysfs() will crash in that case.
Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Mon, 24 Mar 2008 06:41:22 +0000 (17:41 +1100)]
[POWERPC] Don't use 64k pages for ioremap on pSeries
On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured. This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.
Martin Devera [Mon, 24 Mar 2008 05:00:38 +0000 (22:00 -0700)]
sch_htb: fix "too many events" situation
HTB is event driven algorithm and part of its work is to apply
scheduled events at proper times. It tried to defend itself from
livelock by processing only limited number of events per dequeue.
Because of faster computers some users already hit this hardcoded
limit.
This patch limits processing up to 2 jiffies (why not 1 jiffie ?
because it might stop prematurely when only fraction of jiffie
remains).
Signed-off-by: Martin Devera <devik@cdi.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Evgeniy Polyakov [Mon, 24 Mar 2008 04:51:12 +0000 (21:51 -0700)]
connector: convert to single-threaded workqueue
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
We don't need one cqueue thread for each CPU. cqueue is used for
receiving userspace datagrams, which are very rare and thus will
happily live with a single queue.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 23 Mar 2008 10:35:12 +0000 (03:35 -0700)]
[SUNGEM]: Fix NAPI assertion failure.
As reported by Johannes Berg:
I started getting this warning with recent kernels:
[ 773.908927] ------------[ cut here ]------------
[ 773.908954] Badness at net/core/dev.c:2204
...
If we loop more than once in gem_poll(), we'll
use more than the real budget in our gem_rx()
calls, thus eventually trigger the caller's
assertions in net_rx_action().
Subtract "work_done" from "budget" for the second
arg to gem_rx() to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Sun, 23 Mar 2008 10:07:45 +0000 (03:07 -0700)]
BNX2X: prevent ethtool from setting port type
On 10GBaseT boards setting the type to TP will cause the driver to try
to configure 1GBaseT.
Since there are currently no boards that support setting of the port
type, disable this for now.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV4] fib_trie: fix warning from rcu_assign_poinger
This gets rid of a warning caused by the test in rcu_assign_pointer.
I tried to fix rcu_assign_pointer, but that devolved into a long set
of discussions about doing it right that came to no real solution.
Since the test in rcu_assign_pointer for constant NULL would never
succeed in fib_trie, just open code instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
Revert "ide-tape: schedule driver for removal after 6 months"
ide: mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
ide: mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
ide: Documentation/ide/ide.txt fixes
ide: mark special "ide0=" kernel parameters as obsoleted
ide: remove commented out entries from ide_pio_blacklist[]
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix mem leak on dfs referral
[CIFS] file create with acl support enabled is slow
[CIFS] Fix mtime on cp -p when file data cached but written out too late
[CIFS] Fix build problem
[CIFS] cifs: replace remaining __FUNCTION__ occurrences
[CIFS] DFS patch that connects inode with dfs handling ops
Pierre Ossman [Fri, 21 Mar 2008 22:54:50 +0000 (23:54 +0100)]
mmc: use sysfs groups to handle conditional attributes
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.
This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darren Salt [Thu, 13 Mar 2008 15:35:49 +0000 (15:35 +0000)]
PNP: increase the number of PnP memory resources from 12 to 24
Increase the number of PnP memory resources from 12 to 24.
This removes an "exceeded the max num of mem resources" warning on boot. I
also noticed the reservation of two more iomem ranges on the computer on
which this was tested.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk> Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bjorn Helgaas [Fri, 21 Mar 2008 18:08:37 +0000 (12:08 -0600)]
ISAPNP: fix limits of logical device register set
PNP_MAX_MEM and PNP_MAX_PORT are mainly used to size tables of PNP
device resources. In 2.6.24, we increased their values to accomodate
ACPI devices that have many resources:
However, ISAPNP also used these constants as the size of parts of the
logical device register set. This register set is fixed by hardware,
so increasing the constants meant that we were reading and writing
unintended parts of the register set.
This patch changes ISAPNP to use the correct register set sizes (the
same values we used prior to 2.6.24).
Herbert Xu [Sat, 22 Mar 2008 22:47:05 +0000 (15:47 -0700)]
[TCP]: Let skbs grow over a page on fast peers
While testing the virtio-net driver on KVM with TSO I noticed
that TSO performance with a 1500 MTU is significantly worse
compared to the performance of non-TSO with a 16436 MTU. The
packet dump shows that most of the packets sent are smaller
than a page.
Looking at the code this actually is quite obvious as it always
stop extending the packet if it's the first packet yet to be
sent and if it's larger than the MSS. Since each extension is
bound by the page size, this means that (given a 1500 MTU) we're
very unlikely to construct packets greater than a page, provided
that the receiver and the path is fast enough so that packets can
always be sent immediately.
The fix is also quite obvious. The push calls inside the loop
is just an optimisation so that we don't end up doing all the
sending at the end of the loop. Therefore there is no specific
reason why it has to do so at MSS boundaries. For TSO, the
most natural extension of this optimisation is to do the pushing
once the skb exceeds the TSO size goal.
This is what the patch does and testing with KVM shows that the
TSO performance with a 1500 MTU easily surpasses that of a 16436
MTU and indeed the packet sizes sent are generally larger than
16436.
I don't see any obvious downsides for slower peers or connections,
but it would be prudent to test this extensively to ensure that
those cases don't regress.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ide: mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
Mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
(they are layering violation and should be dealt with in the same
way as done by libata - device-mapper should be used instead).
ide: mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
Mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
(nowadays device-driver binding can be changed at runtime through sysfs
and it can also be dealt with using per device driver parameters).
ide: mark special "ide0=" kernel parameters as obsoleted
Mark "ide0=ali14xx|cmd640_vlb|dtc2278|ht6560b|qd65xx|umc8672" kernel
parameters as obsoleted (per host driver replacements have been available
for a long time).
David S. Miller [Sat, 22 Mar 2008 00:01:38 +0000 (17:01 -0700)]
[SPARC64]: Remove most limitations to kernel image size.
Currently kernel images are limited to 8MB in size, and this causes
problems especially when enabling features that take up a lot of
kernel image space such as lockdep.
The code now will align the kernel image size up to 4MB and map that
many locked TLB entries. So, the only practical limitation is the
number of available locked TLB entries which is 16 on Cheetah and 64
on pre-Cheetah sparc64 cpus. Niagara cpus don't actually have hw
locked TLB entry support. Rather, the hypervisor transparently
provides support for "locked" TLB entries since it runs with physical
addressing and does the initial TLB miss processing.
Fully utilizing this change requires some help from SILO, a patch for
which will be submitted to the maintainer. Essentially, SILO will
only currently map up to 8MB for the kernel image and that needs to be
increased.
Note that neither this patch nor the SILO bits will help with network
booting. The openfirmware code will only map up to a certain amount
of kernel image during a network boot and there isn't much we can to
about that other than to implemented a layered network booting
facility. Solaris has this, and calls it "wanboot" and we may
implement something similar at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/sctp/sm_statetable.c:50:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
In file included from net/sctp/sm_statefuns.c:62:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
...
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Oester [Fri, 21 Mar 2008 22:01:50 +0000 (15:01 -0700)]
[IPV4]: Fix null dereference in ip_defrag
Been seeing occasional panics in my testing of 2.6.25-rc in ip_defrag.
Offending line in ip_defrag is here:
net = skb->dev->nd_net
where dev is NULL. Bisected the problem down to commit ac18e7509e7df327e30d6e073a787d922eaf211d ([NETNS][FRAGS]: Make the
inet_frag_queue lookup work in namespaces).
Below patch (idea from Patrick McHardy) fixes the problem for me.
Signed-off-by: Phil Oester <kernel@linuxace.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 21 Mar 2008 17:05:19 +0000 (10:05 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel:
sched: add arch_update_cpu_topology hook.
sched: add exported arch_reinit_sched_domains() to header file.
sched: remove double unlikely from schedule()
sched: cleanup old and rarely used 'debug' features.
x86: fix reboot problem with Dell Optiplex 745, 0KW626 board
we have seen a little problem in rebooting Dell Optiplex 745 with the
0KW626 board. Here is a small patch enabling reboot with this board,
which forces the default reboot path it into the BIOS reboot mode.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pavel Machek [Thu, 13 Mar 2008 22:05:41 +0000 (23:05 +0100)]
x86: fix long standing bug with usb after hibernation with 4GB ram
aperture_64.c takes a piece of memory and makes it into iommu
window... but such window may not be saved by swsusp -- that leads to
oops during hibernation.
Signed-off-by: Pavel Machek <pavel@suse.cz> Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this patch allows hpet=force on nVidia nForce 430 southbridge.
This patch was tested by me on my old Asus A8N-VM CSM (where bios does not
support hpet and does not advertise it via acpi entry). My nForce430 version:
lspci -nn | grep LPC
00:0a.0 ISA bridge [0601]: nVidia Corporation MCP51 LPC Bridge [10de:0260]
(rev a2)
Kernel 2.6.24.3 after patching and using hpet=force reports this:
dmesg | grep -i hpet
Kernel command line: root=/dev/sda8 ro vga=773 video=vesafb:mtrr:4,ywrap
vt.default_utf8=0 hpet=force
Force enabled HPET at base address 0xfed00000
hpet clockevent registered
Time: hpet clocksource has been installed.
Yinghai Lu [Fri, 7 Mar 2008 23:02:50 +0000 (15:02 -0800)]
x86: reserve dma32 early for gart
a system with 256 GB of RAM, when NUMA is disabled crashes the
following way:
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Cannot allocate aperture memory hole (ffff8101c0000000,65536K)
Kernel panic - not syncing: Not enough memory for aperture
Pid: 0, comm: swapper Not tainted 2.6.25-rc4-x86-latest.git #33
solution will be:
1. make memmap allocation get memory above 4G...
2. reserve some dma32 range early before we try to set up memmap for all.
and release that before pci_iommu_alloc, so gart or swiotlb could get some
range under 4g limit for sure.
the patch is using method 2.
because method1 may need more code to handle SPARSEMEM and SPASEMEM_VMEMMAP
will get
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 264245736k/268959744k available (8484k kernel code, 4187464k reserved, 4004k data, 724k init)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Coleman Kane [Tue, 4 Mar 2008 23:05:41 +0000 (15:05 -0800)]
x86: add the DFF (Desktop Form Factor) Dell Optiplex 745 to the reboot errata list
We recently got some of the "Desktop Form Factor" Optiplex 745's in. I
noticed that there's an entry for the SFF one's, but the BIOS model number
of the DFF differs from that of the SFF. We have been reliably
experiencing the same (as far as I can tell) reboot bug as the SFF boxes.
Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Randy Dunlap [Tue, 4 Mar 2008 22:55:47 +0000 (14:55 -0800)]
x86/visws: fix printk format warnings
Fix visws printk format warnings:
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 2 has type 'u32'
/local/linsrc/linux-2.6.24-git15/arch/x86/mach-visws/traps.c:50: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chuck Lever [Tue, 4 Mar 2008 22:55:45 +0000 (14:55 -0800)]
x86: fix {clear,copy}_user_page() declarations in page.h
Clean up: eliminate some compiler noise on x86 when building with strict
warnings enabled, introduced by commit 345b904c.
In file included from include2/asm/thread_info_64.h:12,
from include2/asm/thread_info.h:4,
from
/home/cel/src/linux/nfs-2.6/include/linux/thread_info.h:35,
from
/home/cel/src/linux/nfs-2.6/include/linux/preempt.h:9,
from
/home/cel/src/linux/nfs-2.6/include/linux/spinlock.h:49,
from /home/cel/src/linux/nfs-2.6/include/linux/mmzone.h:7,
from /home/cel/src/linux/nfs-2.6/include/linux/gfp.h:4,
from /home/cel/src/linux/nfs-2.6/include/linux/slab.h:14,
from /home/cel/src/linux/nfs-2.6/fs/nfsd/nfs4acl.c:40:
include2/asm/page.h:55: warning: `inline' is not at beginning of
declaration
include2/asm/page.h:61: warning: `inline' is not at beginning of
declaration
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86: cast cmpxchg and cmpxchg_local result for 386 and 486
mm/slub.c: In function 'slab_alloc':
mm/slub.c:1637: warning: assignment makes pointer from integer without a cast
mm/slub.c:1637: warning: assignment makes pointer from integer without a cast
mm/slub.c: In function 'slab_free':
mm/slub.c:1796: warning: assignment makes pointer from integer without a cast
mm/slub.c:1796: warning: assignment makes pointer from integer without a cast
A cast is needed in the 386 and 486 code because the type is a pointer. In
every other integer case the original cmpxchg code (and the cmpxchg_local
which has been copied from it) worked fine, but since we touch a pointer,
the type needs to be casted in the cmpxchg_local and cmpxchg macros.
The more recent code (586+) does not have this problem (the cast is already
there).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Christoph Lameter <clameter@sgi.com> Cc: Vegard Nossum <vegard.nossum@gmail.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yinghai Lu [Fri, 7 Mar 2008 02:25:16 +0000 (18:25 -0800)]
x86: tight online check in setup_per_cpu_areas
when numa disabled I got this compile warning:
arch/x86/kernel/setup64.c: In function setup_per_cpu_areas:
arch/x86/kernel/setup64.c:147: warning: the address of
contig_page_data will always evaluate as true
it seems we missed checking if the node is online before we try to refer
NODE_DATA. Fix it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
sh: Use relative paths for mach/cpu symlinks.
SH: Use newer, non-deprecated __SPIN_LOCK_UNLOCKED macro.
sh: Fix more user header breakage from sh64 integration.
sh: Fix uImage build error.
sh: Fix up the timer IRQ definition for SH7203.
sh: Fix up the address error exception handler for SH-2.
serial: sh-sci: Fix fifo stall on SH7760/SH7780/SH7785 SCIF.
Jarek Poplawski [Fri, 21 Mar 2008 00:05:13 +0000 (17:05 -0700)]
[NET] ifb: set separate lockdep classes for queue locks
[ 10.536424] =======================================================
[ 10.536424] [ INFO: possible circular locking dependency detected ]
[ 10.536424] 2.6.25-rc3-devel #3
[ 10.536424] -------------------------------------------------------
[ 10.536424] swapper/0 is trying to acquire lock:
[ 10.536424] (&dev->queue_lock){-+..}, at: [<c0299b4a>]
dev_queue_xmit+0x175/0x2f3
[ 10.536424]
[ 10.536424] but task is already holding lock:
[ 10.536424] (&p->tcfc_lock){-+..}, at: [<f8a67154>] tcf_mirred+0x20/0x178
[act_mirred]
[ 10.536424]
[ 10.536424] which lock already depends on the new lock.
lockdep warns of locking order while using ifb with sch_ingress and
act_mirred: ingress_lock, tcfc_lock, queue_lock (usually queue_lock
is at the beginning). This patch is only to tell lockdep that ifb is
a different device (e.g. from eth) and has its own pair of queue
locks. (This warning is a false-positive in common scenario of using
ifb; yet there are possible situations, when this order could be
dangerous; lockdep should warn in such a case.) (With suggestions by
David S. Miller)
Reported-and-tested-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 20 Mar 2008 23:11:27 +0000 (16:11 -0700)]
[TCP]: Fix shrinking windows with window scaling
When selecting a new window, tcp_select_window() tries not to shrink
the offered window by using the maximum of the remaining offered window
size and the newly calculated window size. The newly calculated window
size is always a multiple of the window scaling factor, the remaining
window size however might not be since it depends on rcv_wup/rcv_nxt.
This means we're effectively shrinking the window when scaling it down.
The dump below shows the problem (scaling factor 2^7):
- Window size of 557 (71296) is advertised, up to 3111907257:
IP 172.2.2.3.33000 > 172.2.2.2.33000: . ack 3111835961 win 557 <...>
- New window size of 514 (65792) is advertised, up to 3111907217, 40 bytes
below the last end:
If the sender uses up the entire window before it is shrunk, this can have
chaotic effects on the connection. When sending ACKs, tcp_acceptable_seq()
will notice that the window has been shrunk since tcp_wnd_end() is before
tp->snd_nxt, which makes it choose tcp_wnd_end() as sequence number.
This will fail the receivers checks in tcp_sequence() however since it
is before it's tp->rcv_wup, making it respond with a dupack.
If both sides are in this condition, this leads to a constant flood of
ACKs until the connection times out.
Make sure the window is never shrunk by aligning the remaining window to
the window scaling factor.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
zap_completion_queue() retrieves skbs from completion_queue where they have
zero skb->users counter. Before dev_kfree_skb_any() it should be non-zero
yet, so it's increased now.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Checconi [Thu, 20 Mar 2008 22:54:58 +0000 (15:54 -0700)]
bridge: use time_before() in br_fdb_cleanup()
In br_fdb_cleanup() next_timer and this_timer are in jiffies, so they
should be compared using the time_after() macro.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it> Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Thu, 20 Mar 2008 22:39:41 +0000 (15:39 -0700)]
audit: netlink socket can be auto-bound to pid other than current->pid (v2)
From: Pavel Emelyanov <xemul@openvz.org>
This patch is based on the one from Thomas.
The kauditd_thread() calls the netlink_unicast() and passes
the audit_pid to it. The audit_pid, in turn, is received from
the user space and the tool (I've checked the audit v1.6.9)
uses getpid() to pass one in the kernel. Besides, this tool
doesn't bind the netlink socket to this id, but simply creates
it allowing the kernel to auto-bind one.
That's the preamble.
The problem is that netlink_autobind() _does_not_ guarantees
that the socket will be auto-bound to the current pid. Instead
it uses the current pid as a hint to start looking for a free
id. So, in case of conflict, the audit messages can be sent
to a wrong socket. This can happen (it's unlikely, but can be)
in case some task opens more than one netlink sockets and then
the audit one starts - in this case the audit's pid can be busy
and its socket will be bound to another id.
The proposal is to introduce an audit_nlk_pid in audit subsys,
that will point to the netlink socket to send packets to. It
will most often be equal to audit_pid. The socket id can be
got from the skb's netlink CB right in the audit_receive_msg.
The audit_nlk_pid reset to 0 is not required, since all the
decisions are taken based on audit_pid value only.
Later, if the audit tools will bind the socket themselves, the
kernel will have to provide a way to setup the audit_nlk_pid
as well.
A good side effect of this patch is that audit_pid can later
be converted to struct pid, as it is not longer safe to use
pid_t-s in the presence of pid namespaces. But audit code still
uses the tgid from task_struct in the audit_signal_info and in
the audit_filter_syscall.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 20 Mar 2008 22:17:14 +0000 (15:17 -0700)]
[SCTP]: Fix a race between module load and protosw access
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If a rule using ipt_recent is created with a hit count greater than
ip_pkt_list_tot, the rule will never match as it cannot keep track
of enough timestamps. This patch makes ipt_recent refuse to create such
rules.
With ip_pkt_list_tot's default value of 20, the following can be used
to reproduce the problem.
nc -u -l 0.0.0.0 1234 &
for i in `seq 1 100`; do echo $i | nc -w 1 -u 127.0.0.1 1234; done
This limits it to 20 packets:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 20 --name test --rsource -j DROP
While this is unlimited:
iptables -A OUTPUT -p udp --dport 1234 -m recent --set --name test \
--rsource
iptables -A OUTPUT -p udp --dport 1234 -m recent --update --seconds \
60 --hitcount 21 --name test --rsource -j DROP
With the patch the second rule-set will throw an EINVAL.
Reported-by: Sean Kennedy <skennedy@vcn.com> Signed-off-by: Daniel Hokka Zakrisson <daniel@hozac.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] a100u2w: fix bitmap lookup routine
[SCSI] fix media change events for polled devices
[SCSI] sd, sr: do not emit change event at device add
[SCSI] mpt fusion: Power Management fixes for MPT SAS PCI-E controllers
[SCSI] gdth: Allocate sense_buffer to prevent NULL pointer dereference
[SCSI] arcmsr: fix iounmap error for Type B adapter
[SCSI] isd200: Allocate sense_buffer for hacked up scsi_cmnd
[SCSI] fix bsg queue oops with iscsi logout
[SCSI] Fix dependency problems in SCSI drivers
[SCSI] advansys: Fix bug in AdvLoadMicrocode
Stefan Richter [Sat, 15 Mar 2008 23:56:41 +0000 (00:56 +0100)]
firewire: fix panic in handle_at_packet
This fixes a use-after-free bug in the handling of split transactions.
The AT DMA handler of the request was occasionally executed after the
AR DMA handler of the response. The AT DMA handler then accessed an
already freed packet.
Reported by Johannes Berg.
http://bugzilla.kernel.org/show_bug.cgi?id=9617
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (7367): bug #10211: Fix depencencies for cx2341x
V4L/DVB (7362): tvp5150.c: logical-bitwise and confusion
V4L/DVB (7334): usb video: add a device link to usbvideo devices, else hal will ignore them
V4L/DVB (7330): V4L1 - fix v4l_compat_translate_ioctl possible NULL deref
V4L/DVB (7328): usb/opera1.c: fix a memory leak
V4L/DVB (7291): em28xx: correct use of and fix
V4L/DVB (7285): em28xx: Correct use of ! and &
V4L/DVB (7279): ivtv: Add missing sg_init_table()
V4L/DVB (7268): saa7134: fix: tuner should be loaded before calling saa7134_board_init2()
V4L/DVB (7267): cx88: Fix: Loads tuner module before sending commands to it
V4L/DVB (7251): VIDEO_VIVI must depend on VIDEO_DEV
V4L/DVB (7242): ivtv: fix for yuv filter table check
V4L/DVB (7236): bttv: struct member initialized twice
V4L/DVB (7228): saa7134: fix FM radio support for the Pinnacle PCTV 110i
Serge Hallyn [Fri, 29 Feb 2008 15:14:57 +0000 (15:14 +0000)]
file capabilities: remove cap_task_kill()
The original justification for cap_task_kill() was as follows:
check_kill_permission() does appropriate uid equivalence checks.
However with file capabilities it becomes possible for an
unprivileged user to execute a file with file capabilities
resulting in a more privileged task with the same uid.
However now that cap_task_kill() always returns 0 (permission
granted) when p->uid==current->uid, the whole hook is worthless,
and only likely to create more subtle problems in the corner cases
where it might still be called but return -EPERM. Those cases
are basically when uids are different but euid/suid is equivalent
as per the check in check_kill_permission().
One example of a still-broken application is 'at' for non-root users.
This patch removes cap_task_kill().
Signed-off-by: Serge Hallyn <serge@hallyn.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Earlier-version-tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Thu, 20 Mar 2008 16:33:38 +0000 (17:33 +0100)]
[S390] futex: let futex_atomic_cmpxchg_pt survive early functional tests.
a0c1e9073ef7428a14309cba010633a6cd6719ea "futex: runtime enable pi and
robust functionality" introduces a test wether futex in atomic stuff
works or not.
It does that by writing to address 0 of the kernel address space. This
will crash on older machines where addressing mode switching is enabled
but where the mvcos instruction is not available. Page table walking is
done by hand and therefore the code tries to access current->mm which
is NULL.
Therefore add an extra check, so we survive the early test.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ARM] 4865/1: Register the F75375 device in the GLAN Tank platform code
This patch adds the code required to register the F75375 device on the
GLAN Tank.
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6-omap-h63xx.git / log