David Brownell [Mon, 11 Dec 2006 21:25:08 +0000 (13:25 -0800)]
ARM: OMAP: musb_hdrc: tusb dma patch, minor
Move all DMAREQ for TUSB6010 into its chip setup; it shouldn't be in
either the board-specific code, or the tusb6010 glue. (Note, we still
aren't passing the "which channels" info to the driver...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Hiroshi DOYU [Thu, 7 Dec 2006 23:43:59 +0000 (15:43 -0800)]
ARM: OMAP: Add mailbox support for IVA
This patch adds a generic mailbox interface considering IVA
(Image Video Accelerator) use on 2420, but this patch itself
doesn't contain any IVA driver.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 7 Dec 2006 22:01:23 +0000 (14:01 -0800)]
ARM: OMAP: Avoid updating system time for sub-jiffy interrupts
Updating system time and reprogramming timer can cause latency
issues on busy systems with lots of interrupts with constant
updating of time and reprogramming the system timer.
If a non-timer dyntick interrupt happens within a jiffy from
the last interrupt, updating time and reprogramming the timer
is unnecessary as we will get a timer interrupt soon anyways.
David Brownell [Thu, 7 Dec 2006 01:14:11 +0000 (17:14 -0800)]
ARM: OMAP: MPUIO wake updates
GPIO and MPUIO wake updates:
- Hook MPUIOs into the irq wakeup framework too. This uses a platform
device to update irq enables during system sleep states, instead of
a sys_device, since the latter is no longer needed for such things.
- Also forward enable/disable irq wake requests to the relevant GPIO
controller, so the top level IRQ dispatcher can (eventually) handle
these wakeup events automatically if more than one GPIO pin needs to
be a wakeup event source.
- Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
read-only data under the spinlock.
This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.
Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong: omap1
saves the flags but ignores them, omap2 doesn't even save it. (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:10 +0000 (17:14 -0800)]
ARM: OMAP: speed up gpio irq handling
Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function. On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods. Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Wait a fixed amount of time between writing to the columns
register and reading rows state to allow the keypad to respond
on Palm Tungsten E and Zire 71. The value for Zire 71 keypad
was tested by Marek Vasut.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic support for Siemens SX1. More patches are available,
with video driver, mixer, and serial ports working. That is enough to
do gsm calls with right userland.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
Marek Vašut [Thu, 7 Dec 2006 01:14:07 +0000 (17:14 -0800)]
ARM: OMAP: Palm Zire71 minor fixes
This patch makes minor changes in palmz71 board file (formating changes) and
renames one GPIO (PALMZ71_PINTDAV_GPIO to PALMZ71_PENIRQ_GPIO) in
board-palmz71.h and board-palmz71.c .
Signed-off-by: Marek Vašut <marek.vasut@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: abstract debug card setup (smc, leds)
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: h4 must have blinky leds!!
This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.
It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.
In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO). Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
On Fri, Oct 27, 2006 at 05:16:59PM +0100, Jonathan McDowell wrote:
> However having prodded further I'm seeing incorrect key parsing with
> the omap-keypad driver under both -rc2 and -rc3 (works fine in
> 2.6.18-omap1). Numerous keys now returns strings of characters rather
> than the single expected character. A few keys still work as expected
> however. Before I dig in further is anyone else seeing anything similar?
This appears to be due to the addition of keymapsize to the
omap_kp_platform_data structure. The patch below fixes things up for
the Delta; other boards appear to have already had this done.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:59 +0000 (17:13 -0800)]
ARM: OMAP: gpio object shrinkage, cleanup
More GPIO/IRQ cleanup:
- compile-time removal of much useless code
* mpuio support on non-OMAP1.
* 15xx/730/24xx gpio support on 1610
* 15xx/730/16xx gpio support on 24xx
* etc
- remove all BUG() calls, which are always bad news ... replaced some
with normal fault reports for that call, others with WARN_ON(1).
- small mpuio bugfix: add missing set_type() method
Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:55 +0000 (17:13 -0800)]
ARM: OMAP: omap2/gpmc updates
GPMC updates:
- bugfixes: wrong/missing flags, omitted write, wrong test
- don't map memory segments starting at zero
- improve debug messaging
- export gpmc_get_fclk_perio]d() since it's needed to calc timings
- expect gpmc_cs_set_timings() caller to have initialized sync vs async
Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kyungmin Park [Thu, 7 Dec 2006 01:13:54 +0000 (17:13 -0800)]
ARM: OMAP: 24xx pinmux updates
Add some OMAP 24xx pin mux declarations to support:
- TUSB 6010 EVM (on H4)
- All three full speed USB ports
- GPIOs used with USB0 on Apollon and H4
For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:53 +0000 (17:13 -0800)]
ARM: OMAP: /sys/kernel/debug/omap_gpio
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.
Includes minor bugfixes: recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Thu, 7 Dec 2006 01:13:52 +0000 (17:13 -0800)]
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Deak [Thu, 7 Dec 2006 01:13:50 +0000 (17:13 -0800)]
ARM: OMAP: FB: add controller platform data
Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:13:51 +0000 (17:13 -0800)]
ARM: OMAP: Fix warning in clock.c
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following compiler warning (only visible with
CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Thomas Gleixner [Sun, 25 Mar 2007 12:42:51 +0000 (14:42 +0200)]
[PATCH] clocksource: Fix thinko in watchdog selection
The watchdog implementation excludes low res / non continuous
clocksources from being selected as a watchdog reference
unintentionally.
Allow using jiffies/PIT as a watchdog reference as long as no better
clocksource is available. This is necessary to detect TSC breakage on
systems, which have no pmtimer/hpet.
The main goal of the initial patch (preventing to switch to highres/nohz
when no reliable fallback clocksource is available) is still guaranteed
by the checks in clocksource_watchdog().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sun, 25 Mar 2007 12:31:17 +0000 (14:31 +0200)]
[PATCH] dynticks: fix hrtimer rounding error in next_timer_interrupt
The rework of next_timer_interrupt() fixed the timer wheel bugs, but
invented a rounding error versus the next hrtimer event. This is caused
by the conversion of the hrtimer internal representation to relative
jiffies.
This causes bug #8100:
http://bugzilla.kernel.org/show_bug.cgi?id=8100
next_timer_interrupt() returns "now" in such a case and causes the code
in tick_nohz_stop_sched_tick() to trigger the timer softirq, which is
bogus as no timer is due for expiry. This results in an endless context
switching between idle and ksoftirqd until a timer is due for expiry.
Modify the hrtimer evaluation so that, it returns now + 1, when the
conversion results in a delta < 1 jiffie.
It's confirmed to resolve bug #8100
Reported-by: Emil Karlson <jkarlson@cc.hut.fi> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Krufky [Sat, 24 Mar 2007 17:21:53 +0000 (13:21 -0400)]
[PATCH] cx88-dvb: fix nxt200x rf input switching
After dvb tuner refactoring, the pllbuff has been altered such that the pll
address is now stored in buf[0]. Instead of sending buf to set_pll_input,
we should send buf+1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Ivan Andrewjeski <ivan@fiero-gt.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been reported by Julian Deng that configuring the pxa27x i2c SCL line as output generates a short negative pulse on it during the call to pxa_gpio_mode(GPIO117_I2CSCL_MD); as it first switches it to output and then configures it for the alternate function. The SCL line is in fact bidirectional and can also be configured as 117 | GPIO_ALT_FN_1_IN, in which case the pulse is not generated. This is exactly what this patch does.
Author: Julian Deng <dengtj@sitek.cn>
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ralf Baechle [Sat, 24 Mar 2007 14:09:59 +0000 (14:09 +0000)]
[MIPS] SB1: Fix pile of gcc's bogus format string warnings.
CC arch/mips/mm/cerr-sb1.o
arch/mips/mm/cerr-sb1.c: In function 'sb1_cache_error':
arch/mips/mm/cerr-sb1.c:235: warning: format '%010llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_ic':
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:385: warning: format '%016llX' expects type 'long long unsigned int', but argument 6 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c: In function 'extract_dc':
arch/mips/mm/cerr-sb1.c:523: warning: format '%010llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:523: warning: format '%016llX' expects type 'long long unsigned int', but argument 7 has type 'uint64_t'
arch/mips/mm/cerr-sb1.c:570: warning: format '%016llX' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
LD arch/mips/mm/built-in.o
Ralf Baechle [Sat, 24 Mar 2007 13:06:43 +0000 (13:06 +0000)]
[MIPS] ARC: Fix warning.
The missing cast did result a warning when calling an 32-bit ARC firmware
function that takes 5 arguments where the 5th argument is a pointer from a
64-bit kernel.
Ralf Baechle [Tue, 20 Mar 2007 13:56:50 +0000 (13:56 +0000)]
[MIPS] Fix pipeline hazard.
In the the sequence:
ei
..
mfc0 $x, $status
the mfc0 may not see the SR_IE bit set. This was a deliberate bug in the
kernel code because we knew this was a safe thing to do on all R2 silicon
so far but new silicon is changing this.
Franck Bui-Huu [Mon, 19 Mar 2007 16:36:42 +0000 (17:36 +0100)]
[MIPS] Always use virt_to_phys() when translating kernel addresses
This patch fixes two places where we used plain 'x - PAGE_OFFSET' to
achieve virtual to physical address convertions. This type of convertion
is no more allowed since commit 6f284a2ce7b8bc49cb8455b1763357897a899abb.
Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
[Build fixes for machines that don't use the generic dma-coherence.h]
Thomas Gleixner [Sat, 24 Mar 2007 00:14:37 +0000 (17:14 -0700)]
[PATCH] x86_64: avoid sending LOCAL_TIMER_VECTOR IPI to itself
Ray Lee reported, that on an UP kernel with "noapic" command line option
set, the box locks hard during boot.
Adding some debug printks revealed, that the last action on the box
before stalling was "Send IPI" - a debug printk which was put into
smp_send_timer_broadcast_ipi().
It seems that send_IPI_mask(mask, LOCAL_TIMER_VECTOR) fails when
"noapic" is set on the command line on an UP kernel.
Aside of that it does not make much sense to trigger an interrupt
instead of calling the function directly on the CPU which gets the
PIT/HPET interrupt in case of broadcasting.
Reported-by: Ray Lee <ray-lk@madrabbit.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ray Lee <ray-lk@madrabbit.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Fri, 23 Mar 2007 21:26:33 +0000 (14:26 -0700)]
[PATCH] i386: clear segment register padding in core dumps
The segment register slots in struct pt_regs are padded to 32 bits.
Some of these are stored with instructions like "pushl %es", which
leaves the high 16 bits as they were. So the high bits of these
fields in struct pt_regs contain kernel stack garbage. These bits are
ignored by everything and never leak to user space, except in core
dumps. The user struct pt_regs is always at the base of the thread's
kernel stack and so it seems unlikely the information that leaks from
here is ever worthwhile so as to be a security concern, but I'm not
sure about that. It has been this way for ages; userland consumers of
core dumps all mask off these high bits themselves. So it is not urgent.
This change masks off the padding bits of the segment register slots
in core dumps. ptrace already masks off these high bits, so this
makes the values in core dumps consistent with what ptrace would
report just before the process died.
As I read the processor manuals, the cs and ss values will always be
padded with zero bits rather than stack garbage. But unlike "pushl %es",
this is not simple to test with a userland program. So I added the two
instructions rather than wonder if they are really never necessary.
I think that x86_64 does not have this problem (for either 32-bit or
64-bit processes). It only uses "mov" instructions from segment
registers, which zero-extend.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 23 Mar 2007 18:02:45 +0000 (11:02 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: fix oops on "modprobe -r ohci1394" after network class_device conversion
Linus Torvalds [Fri, 23 Mar 2007 18:01:41 +0000 (11:01 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] ewrk3: correct card detection bug
cxgb3 - fix white spaces in drivers/net/Kconfig
myri10ge: update driver version to 1.3.0-1.226
myri10ge: fix management of >4kB allocated pages
myri10ge: update wcfifo and intr_coal_delay default values
myri10ge: Serverworks HT2100 provides aligned PCIe completion
mv643xx_eth: add mv643xx_eth_shutdown function
SAA9730: Fix large pile of warnings
Revert "ucc_geth: returns NETDEV_TX_BUSY when BD ring is full"
cxgb3 - T3B2 pcie config space
cxgb3 - Fix potential MAC hang
cxgb3 - Auto-load FW if mismatch detected
cxgb3 - fix ethtool cmd on multiple queues port
Fix return code in pci-skeleton.c
skge: use per-port phy locking
skge: mask irqs when device down
skge: deadlock on tx timeout
[PATCH] airo: Fix an error path memory leak
[PATCH] bcm43xx: MANUALWLAN fixes
Guido Guenther [Fri, 23 Mar 2007 07:10:01 +0000 (00:10 -0700)]
[PATCH] rivafb: fix initial brightness
This is the rivafb equivalent of 238576e12fef1d52751c6e08db2d0bdb0e248caf.
It fixes rivafb having a default backlight brightness of 0 (no picture at
all) on a PBook 6,1.
Signed-off-by: Guido Guenther <agx@sigxcpu.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Acked-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Danny Kukawka [Fri, 23 Mar 2007 07:10:01 +0000 (00:10 -0700)]
[PATCH] add Fujitsu Siemens Tablet PC devices to 8250_pnp.c
Adds device ids of two Fujitsu Siemens Tablet PCs to pnp_dev_table
Signed-off-by: Danny Kukawka <dkukawka@suse.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 23 Mar 2007 07:10:00 +0000 (00:10 -0700)]
[PATCH] FDPIC: fix the /proc/pid/stat representation of executable boundaries
Fix the /proc/pid/stat representation of executable boundaries. It should
show the bounds of the executable, but instead shows the bounds of the
loader.
Before the patch is applied, the bug can be seen by examining, say, inetd:
Which is wrong. After the patch is applied, the maps file is pretty much
identical (there's some minor shuffling of the location of some of the
anonymous VMAs), but the stat file is now:
Thomas Gleixner [Fri, 23 Mar 2007 15:08:01 +0000 (16:08 +0100)]
[PATCH] i386: add command line option "local_apic_timer_c2_ok"
It turned out that it is almost impossible to trust ACPI, BIOS & Co.
regarding the C states. This was the reason to switch the local apic
timer off in C2 state already. OTOH there are sane and well behaving
systems, which get punished by that decision.
Allow the user to confirm that the local apic timer is trustworthy in C2
state. This keeps the default behaviour on the safe side.
Linus Torvalds [Fri, 23 Mar 2007 15:03:47 +0000 (08:03 -0700)]
Revert "ACPI: Only use IPI on known broken machines (AMD, Dothan/BaniasPentium M)"
This reverts commit 25496caec111481161e7f06bbfa12a533c43cc6f, which
broke bootup on at least Ingo's ThinkPad T60. Need to figure out
exactly what is wrong before we can re-do the logic.
Requested-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Renninger <trenn@suse.de> Cc: Len Brown <len.brown@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Richter [Tue, 20 Mar 2007 21:43:22 +0000 (22:43 +0100)]
ieee1394: fix oops on "modprobe -r ohci1394" after network class_device conversion
The networking subsystem has been converted from class_device to device
but ieee1394 hasn't. This results in a 100% reproducible NULL pointer
dereference if the ohci1394 driver module is unloaded while the eth1394
module is still loaded.
http://lkml.org/lkml/2006/11/16/147
http://lkml.org/lkml/2007/3/14/4
This is a regression in 2.6.21-rc1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Tested-by: Ismail Dönmez <ismail@pardus.org.tr>
Jeff Garzik [Fri, 23 Mar 2007 06:03:29 +0000 (02:03 -0400)]
[netdrvr] ewrk3: correct card detection bug
Arwin Vosselman pointed out:
> The ewrk3-driver doesn't function with 2.6.16-kernels (used 2.6.16.41 for
> my tests). Cards will never be detected due to this bug.
>
> drivers/net/ewrks3.c:
> Line 417 reads:
>
> if (nicsr == (CSR_TXD | CSR_RXD))
>
> that should be:
>
> if (nicsr != (CSR_TXD | CSR_RXD))
>
> Comparison with the same line in v2.4 shows why:
>
> 2.4:
> if (nicsr == (CSR_TXD | CSR_RXD)){
>
> blah, blah
> ==========
> 2.6:
> if (nicsr == (CSR_TXD | CSR_RXD))
> return -ENXIO;
>
> blah, blah
> ==========
>
> blah,blah will not, but should, be executed in 2.6 with a card being present.
>
> The fix mentioned above solves this bug.
projects / linux-2.6-omap-h63xx.git / log