From: Larry Finger Date: Tue, 5 Aug 2008 16:23:16 +0000 (-0500) Subject: p54: Fix for TX sequence number problem X-Git-Tag: v2.6.27-rc3~69^2~10 X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=commitdiff_plain;h=eda0c003d1ff14c99d8476b482377ccfaf967b6c;p=linux-2.6-omap-h63xx.git p54: Fix for TX sequence number problem Following "mac80211: fix TX sequence numbers", if a packet has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be supplied, either by hardware or software. AFAIK, no such hardware exists for the p54, thus it must be done in software. With this patch, a connection qith p54usb is stable, whereas the interface went off-line in 2-3 hours without this change. Note that this code will have to be reworked for proper sequence numbers on beacons. In addition, the sequence number has been placed in the hardware state, not the vif state. Signed-off-by: Larry Finger Signed-off-by: John W. Linville --- diff --git a/drivers/net/wireless/p54/p54.h b/drivers/net/wireless/p54/p54.h index cac9a515b82..4801a363507 100644 --- a/drivers/net/wireless/p54/p54.h +++ b/drivers/net/wireless/p54/p54.h @@ -52,6 +52,7 @@ struct p54_common { int (*open)(struct ieee80211_hw *dev); void (*stop)(struct ieee80211_hw *dev); int mode; + u16 seqno; struct mutex conf_mutex; u8 mac_addr[ETH_ALEN]; u8 bssid[ETH_ALEN]; diff --git a/drivers/net/wireless/p54/p54common.c b/drivers/net/wireless/p54/p54common.c index 4da89ea9b56..2d2d33612ae 100644 --- a/drivers/net/wireless/p54/p54common.c +++ b/drivers/net/wireless/p54/p54common.c @@ -553,6 +553,7 @@ static int p54_tx(struct ieee80211_hw *dev, struct sk_buff *skb) struct ieee80211_tx_queue_stats *current_queue; struct p54_common *priv = dev->priv; struct p54_control_hdr *hdr; + struct ieee80211_hdr *ieee80211hdr = (struct ieee80211_hdr *)skb->data; struct p54_tx_control_allocdata *txhdr; size_t padding, len; u8 rate; @@ -605,6 +606,19 @@ static int p54_tx(struct ieee80211_hw *dev, struct sk_buff *skb) if (padding) txhdr->align[0] = padding; + /* FIXME: The sequence that follows is needed for this driver to + * work with mac80211 since "mac80211: fix TX sequence numbers". + * As with the temporary code in rt2x00, changes will be needed + * to get proper sequence numbers on beacons. In addition, this + * patch places the sequence number in the hardware state, which + * limits us to a single virtual state. + */ + if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { + if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) + priv->seqno += 0x10; + ieee80211hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); + ieee80211hdr->seq_ctrl |= cpu_to_le16(priv->seqno); + } /* modifies skb->cb and with it info, so must be last! */ p54_assign_address(dev, skb, hdr, skb->len);