From: David Brownell Date: Tue, 6 Jan 2009 22:41:41 +0000 (-0800) Subject: spi_gpio driver X-Git-Tag: v2.6.29-rc1~322 X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=commitdiff_plain;h=d29389de0b0ee1715333bafc6ac3f22a75aa4313;p=linux-2.6-omap-h63xx.git spi_gpio driver Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as "spi_gpio", so it works with arbitrary GPIOs and can be configured through platform_data. Such SPI masters support: - any number of bus instances (bus_num is the platform_device.id) - any number of chipselects (one GPIO per spi_device) - all four SPI_MODE values, and SPI_CS_HIGH - i/o word sizes from 1 to 32 bits; - devices configured as with any other spi_master controller When configured using platform_data, this provides relatively low clock rates. On platforms that support inlined GPIO calls, significantly improved transfer speeds are also possible with a semi-custom driver. (It's still painful when accessing flash memory, but less so.) Sanity checked by using this version to replace both native controllers on a board with six different SPI slaves, relying on three different SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation. [akpm@linux-foundation.org: cleanups] Signed-off-by: David Brownell Acked-by: Magnus Damm Tested-by: Magnus Damm Cc: Torgil Svensson Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index b9d0efb6803..4a6fe01831a 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -78,7 +78,7 @@ config SPI_AU1550 will be called au1550_spi. config SPI_BITBANG - tristate "Bitbanging SPI master" + tristate "Utilities for Bitbanging SPI masters" help With a few GPIO pins, your system can bitbang the SPI protocol. Select this to get SPI support through I/O pins (GPIO, parallel @@ -100,6 +100,22 @@ config SPI_BUTTERFLY inexpensive battery powered microcontroller evaluation board. This same cable can be used to flash new firmware. +config SPI_GPIO + tristate "GPIO-based bitbanging SPI Master" + depends on GENERIC_GPIO + select SPI_BITBANG + help + This simple GPIO bitbanging SPI master uses the arch-neutral GPIO + interface to manage MOSI, MISO, SCK, and chipselect signals. SPI + slaves connected to a bus using this driver are configured as usual, + except that the spi_board_info.controller_data holds the GPIO number + for the chipselect used by this controller driver. + + Note that this driver often won't achieve even 1 Mbit/sec speeds, + making it unusually slow for SPI. If your platform can inline + GPIO operations, you should be able to leverage that for better + speed with a custom version of this driver; see the source code. + config SPI_IMX tristate "Freescale iMX SPI controller" depends on ARCH_IMX && EXPERIMENTAL diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index ccf18de34e1..5e9f521b884 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o obj-$(CONFIG_SPI_AU1550) += au1550_spi.o obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o +obj-$(CONFIG_SPI_GPIO) += spi_gpio.o obj-$(CONFIG_SPI_IMX) += spi_imx.o obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o diff --git a/drivers/spi/spi_gpio.c b/drivers/spi/spi_gpio.c new file mode 100644 index 00000000000..49698cabc30 --- /dev/null +++ b/drivers/spi/spi_gpio.c @@ -0,0 +1,360 @@ +/* + * spi_gpio.c - SPI master driver using generic bitbanged GPIO + * + * Copyright (C) 2006,2008 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include +#include +#include +#include + +#include +#include +#include + + +/* + * This bitbanging SPI master driver should help make systems usable + * when a native hardware SPI engine is not available, perhaps because + * its driver isn't yet working or because the I/O pins it requires + * are used for other purposes. + * + * platform_device->driver_data ... points to spi_gpio + * + * spi->controller_state ... reserved for bitbang framework code + * spi->controller_data ... holds chipselect GPIO + * + * spi->master->dev.driver_data ... points to spi_gpio->bitbang + */ + +struct spi_gpio { + struct spi_bitbang bitbang; + struct spi_gpio_platform_data pdata; + struct platform_device *pdev; +}; + +/*----------------------------------------------------------------------*/ + +/* + * Because the overhead of going through four GPIO procedure calls + * per transferred bit can make performance a problem, this code + * is set up so that you can use it in either of two ways: + * + * - The slow generic way: set up platform_data to hold the GPIO + * numbers used for MISO/MOSI/SCK, and issue procedure calls for + * each of them. This driver can handle several such busses. + * + * - The quicker inlined way: only helps with platform GPIO code + * that inlines operations for constant GPIOs. This can give + * you tight (fast!) inner loops, but each such bus needs a + * new driver. You'll define a new C file, with Makefile and + * Kconfig support; the C code can be a total of six lines: + * + * #define DRIVER_NAME "myboard_spi2" + * #define SPI_MISO_GPIO 119 + * #define SPI_MOSI_GPIO 120 + * #define SPI_SCK_GPIO 121 + * #define SPI_N_CHIPSEL 4 + * #include "spi_gpio.c" + */ + +#ifndef DRIVER_NAME +#define DRIVER_NAME "spi_gpio" + +#define GENERIC_BITBANG /* vs tight inlines */ + +/* all functions referencing these symbols must define pdata */ +#define SPI_MISO_GPIO ((pdata)->miso) +#define SPI_MOSI_GPIO ((pdata)->mosi) +#define SPI_SCK_GPIO ((pdata)->sck) + +#define SPI_N_CHIPSEL ((pdata)->num_chipselect) + +#endif + +/*----------------------------------------------------------------------*/ + +static inline const struct spi_gpio_platform_data * __pure +spi_to_pdata(const struct spi_device *spi) +{ + const struct spi_bitbang *bang; + const struct spi_gpio *spi_gpio; + + bang = spi_master_get_devdata(spi->master); + spi_gpio = container_of(bang, struct spi_gpio, bitbang); + return &spi_gpio->pdata; +} + +/* this is #defined to avoid unused-variable warnings when inlining */ +#define pdata spi_to_pdata(spi) + +static inline void setsck(const struct spi_device *spi, int is_on) +{ + gpio_set_value(SPI_SCK_GPIO, is_on); +} + +static inline void setmosi(const struct spi_device *spi, int is_on) +{ + gpio_set_value(SPI_MOSI_GPIO, is_on); +} + +static inline int getmiso(const struct spi_device *spi) +{ + return gpio_get_value(SPI_MISO_GPIO); +} + +#undef pdata + +/* + * NOTE: this clocks "as fast as we can". It "should" be a function of the + * requested device clock. Software overhead means we usually have trouble + * reaching even one Mbit/sec (except when we can inline bitops), so for now + * we'll just assume we never need additional per-bit slowdowns. + */ +#define spidelay(nsecs) do {} while (0) + +#define EXPAND_BITBANG_TXRX +#include + +/* + * These functions can leverage inline expansion of GPIO calls to shrink + * costs for a txrx bit, often by factors of around ten (by instruction + * count). That is particularly visible for larger word sizes, but helps + * even with default 8-bit words. + * + * REVISIT overheads calling these functions for each word also have + * significant performance costs. Having txrx_bufs() calls that inline + * the txrx_word() logic would help performance, e.g. on larger blocks + * used with flash storage or MMC/SD. There should also be ways to make + * GCC be less stupid about reloading registers inside the I/O loops, + * even without inlined GPIO calls; __attribute__((hot)) on GCC 4.3? + */ + +static u32 spi_gpio_txrx_word_mode0(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits); +} + +static u32 spi_gpio_txrx_word_mode1(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, bits); +} + +static u32 spi_gpio_txrx_word_mode2(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha0(spi, nsecs, 1, word, bits); +} + +static u32 spi_gpio_txrx_word_mode3(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha1(spi, nsecs, 1, word, bits); +} + +/*----------------------------------------------------------------------*/ + +static void spi_gpio_chipselect(struct spi_device *spi, int is_active) +{ + unsigned long cs = (unsigned long) spi->controller_data; + + /* set initial clock polarity */ + if (is_active) + setsck(spi, spi->mode & SPI_CPOL); + + /* SPI is normally active-low */ + gpio_set_value(cs, (spi->mode & SPI_CS_HIGH) ? is_active : !is_active); +} + +static int spi_gpio_setup(struct spi_device *spi) +{ + unsigned long cs = (unsigned long) spi->controller_data; + int status = 0; + + if (spi->bits_per_word > 32) + return -EINVAL; + + if (!spi->controller_state) { + status = gpio_request(cs, spi->dev.bus_id); + if (status) + return status; + status = gpio_direction_output(cs, spi->mode & SPI_CS_HIGH); + } + if (!status) + status = spi_bitbang_setup(spi); + if (status) { + if (!spi->controller_state) + gpio_free(cs); + } + return status; +} + +static void spi_gpio_cleanup(struct spi_device *spi) +{ + unsigned long cs = (unsigned long) spi->controller_data; + + gpio_free(cs); + spi_bitbang_cleanup(spi); +} + +static int __init spi_gpio_alloc(unsigned pin, const char *label, bool is_in) +{ + int value; + + value = gpio_request(pin, label); + if (value == 0) { + if (is_in) + value = gpio_direction_input(pin); + else + value = gpio_direction_output(pin, 0); + } + return value; +} + +static int __init +spi_gpio_request(struct spi_gpio_platform_data *pdata, const char *label) +{ + int value; + + /* NOTE: SPI_*_GPIO symbols may reference "pdata" */ + + value = spi_gpio_alloc(SPI_MOSI_GPIO, label, false); + if (value) + goto done; + + value = spi_gpio_alloc(SPI_MISO_GPIO, label, true); + if (value) + goto free_mosi; + + value = spi_gpio_alloc(SPI_SCK_GPIO, label, false); + if (value) + goto free_miso; + + goto done; + +free_miso: + gpio_free(SPI_MISO_GPIO); +free_mosi: + gpio_free(SPI_MOSI_GPIO); +done: + return value; +} + +static int __init spi_gpio_probe(struct platform_device *pdev) +{ + int status; + struct spi_master *master; + struct spi_gpio *spi_gpio; + struct spi_gpio_platform_data *pdata; + + pdata = pdev->dev.platform_data; +#ifdef GENERIC_BITBANG + if (!pdata || !pdata->num_chipselect) + return -ENODEV; +#endif + + status = spi_gpio_request(pdata, dev_name(&pdev->dev)); + if (status < 0) + return status; + + master = spi_alloc_master(&pdev->dev, sizeof *spi_gpio); + if (!master) { + status = -ENOMEM; + goto gpio_free; + } + spi_gpio = spi_master_get_devdata(master); + platform_set_drvdata(pdev, spi_gpio); + + spi_gpio->pdev = pdev; + if (pdata) + spi_gpio->pdata = *pdata; + + master->bus_num = pdev->id; + master->num_chipselect = SPI_N_CHIPSEL; + master->setup = spi_gpio_setup; + master->cleanup = spi_gpio_cleanup; + + spi_gpio->bitbang.master = spi_master_get(master); + spi_gpio->bitbang.chipselect = spi_gpio_chipselect; + spi_gpio->bitbang.txrx_word[SPI_MODE_0] = spi_gpio_txrx_word_mode0; + spi_gpio->bitbang.txrx_word[SPI_MODE_1] = spi_gpio_txrx_word_mode1; + spi_gpio->bitbang.txrx_word[SPI_MODE_2] = spi_gpio_txrx_word_mode2; + spi_gpio->bitbang.txrx_word[SPI_MODE_3] = spi_gpio_txrx_word_mode3; + spi_gpio->bitbang.setup_transfer = spi_bitbang_setup_transfer; + spi_gpio->bitbang.flags = SPI_CS_HIGH; + + status = spi_bitbang_start(&spi_gpio->bitbang); + if (status < 0) { + spi_master_put(spi_gpio->bitbang.master); +gpio_free: + gpio_free(SPI_MISO_GPIO); + gpio_free(SPI_MOSI_GPIO); + gpio_free(SPI_SCK_GPIO); + spi_master_put(master); + } + + return status; +} + +static int __exit spi_gpio_remove(struct platform_device *pdev) +{ + struct spi_gpio *spi_gpio; + struct spi_gpio_platform_data *pdata; + int status; + + spi_gpio = platform_get_drvdata(pdev); + pdata = pdev->dev.platform_data; + + /* stop() unregisters child devices too */ + status = spi_bitbang_stop(&spi_gpio->bitbang); + spi_master_put(spi_gpio->bitbang.master); + + platform_set_drvdata(pdev, NULL); + + gpio_free(SPI_MISO_GPIO); + gpio_free(SPI_MOSI_GPIO); + gpio_free(SPI_SCK_GPIO); + + return status; +} + +MODULE_ALIAS("platform:" DRIVER_NAME); + +static struct platform_driver spi_gpio_driver = { + .driver.name = DRIVER_NAME, + .driver.owner = THIS_MODULE, + .remove = __exit_p(spi_gpio_remove), +}; + +static int __init spi_gpio_init(void) +{ + return platform_driver_probe(&spi_gpio_driver, spi_gpio_probe); +} +module_init(spi_gpio_init); + +static void __exit spi_gpio_exit(void) +{ + platform_driver_unregister(&spi_gpio_driver); +} +module_exit(spi_gpio_exit); + + +MODULE_DESCRIPTION("SPI master driver using generic bitbanged GPIO "); +MODULE_AUTHOR("David Brownell"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/spi/spi_gpio.h b/include/linux/spi/spi_gpio.h new file mode 100644 index 00000000000..0f01a0f1f40 --- /dev/null +++ b/include/linux/spi/spi_gpio.h @@ -0,0 +1,60 @@ +#ifndef __LINUX_SPI_GPIO_H +#define __LINUX_SPI_GPIO_H + +/* + * For each bitbanged SPI bus, set up a platform_device node with: + * - name "spi_gpio" + * - id the same as the SPI bus number it implements + * - dev.platform data pointing to a struct spi_gpio_platform_data + * + * Or, see the driver code for information about speedups that are + * possible on platforms that support inlined access for GPIOs (no + * spi_gpio_platform_data is used). + * + * Use spi_board_info with these busses in the usual way, being sure + * that the controller_data being the GPIO used for each device's + * chipselect: + * + * static struct spi_board_info ... [] = { + * ... + * // this slave uses GPIO 42 for its chipselect + * .controller_data = (void *) 42, + * ... + * // this one uses GPIO 86 for its chipselect + * .controller_data = (void *) 86, + * ... + * }; + * + * If the bitbanged bus is later switched to a "native" controller, + * that platform_device and controller_data should be removed. + */ + +/** + * struct spi_gpio_platform_data - parameter for bitbanged SPI master + * @sck: number of the GPIO used for clock output + * @mosi: number of the GPIO used for Master Output, Slave In (MOSI) data + * @miso: number of the GPIO used for Master Input, Slave Output (MISO) data + * @num_chipselect: how many slaves to allow + * + * All GPIO signals used with the SPI bus managed through this driver + * (chipselects, MOSI, MISO, SCK) must be configured as GPIOs, instead + * of some alternate function. + * + * It can be convenient to use this driver with pins that have alternate + * functions associated with a "native" SPI controller if a driver for that + * controller is not available, or is missing important functionality. + * + * On platforms which can do so, configure MISO with a weak pullup unless + * there's an external pullup on that signal. That saves power by avoiding + * floating signals. (A weak pulldown would save power too, but many + * drivers expect to see all-ones data as the no slave "response".) + */ +struct spi_gpio_platform_data { + unsigned sck; + unsigned mosi; + unsigned miso; + + u16 num_chipselect; +}; + +#endif /* __LINUX_SPI_GPIO_H */