From: David Brownell Date: Tue, 6 Jan 2009 22:42:26 +0000 (-0800) Subject: twl4030-gpio: cleanup debounce X-Git-Tag: v2.6.29-rc1~276 X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=commitdiff_plain;h=cabb3fc4bd1628c37c37e054960eb3e4bf30dc26;p=linux-2.6-omap-h63xx.git twl4030-gpio: cleanup debounce Provide a static debounce configuration mechanism for twl4030 GPIOs, replacing the previous dynamic one. The single user of that mechanism was for MMC card detect debouncing. Boards can provide a bitmask saying which GPIOs to debounce (30 msec). It's always enabled for pins with the MMC card-detect/VMMCx link active, so most boards won't need to set the debounce mask. This is a net code shrink, including runtime footprint. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- diff --git a/drivers/gpio/twl4030-gpio.c b/drivers/gpio/twl4030-gpio.c index 37d3eec8730..afad1479214 100644 --- a/drivers/gpio/twl4030-gpio.c +++ b/drivers/gpio/twl4030-gpio.c @@ -202,37 +202,6 @@ static int twl4030_get_gpio_datain(int gpio) return ret; } -/* - * Configure debounce timing value for a GPIO pin on TWL4030 - */ -int twl4030_set_gpio_debounce(int gpio, int enable) -{ - u8 d_bnk = gpio >> 3; - u8 d_msk = BIT(gpio & 0x7); - u8 reg = 0; - u8 base = 0; - int ret = 0; - - if (unlikely((gpio >= TWL4030_GPIO_MAX) - || !(gpio_usage_count & BIT(gpio)))) - return -EPERM; - - base = REG_GPIO_DEBEN1 + d_bnk; - mutex_lock(&gpio_lock); - ret = gpio_twl4030_read(base); - if (ret >= 0) { - if (enable) - reg = ret | d_msk; - else - reg = ret & ~d_msk; - - ret = gpio_twl4030_write(base, reg); - } - mutex_unlock(&gpio_lock); - return ret; -} -EXPORT_SYMBOL(twl4030_set_gpio_debounce); - /*----------------------------------------------------------------------*/ static int twl_request(struct gpio_chip *chip, unsigned offset) @@ -405,6 +374,23 @@ static int __devinit gpio_twl4030_pulls(u32 ups, u32 downs) REG_GPIOPUPDCTR1, 5); } +static int __devinit gpio_twl4030_debounce(u32 debounce, u8 mmc_cd) +{ + u8 message[4]; + + /* 30 msec of debouncing is always used for MMC card detect, + * and is optional for everything else. + */ + message[1] = (debounce & 0xff) | (mmc_cd & 0x03); + debounce >>= 8; + message[2] = (debounce & 0xff); + debounce >>= 8; + message[3] = (debounce & 0x03); + + return twl4030_i2c_write(TWL4030_MODULE_GPIO, message, + REG_GPIO_DEBEN1, 3); +} + static int gpio_twl4030_remove(struct platform_device *pdev); static int __devinit gpio_twl4030_probe(struct platform_device *pdev) @@ -439,6 +425,12 @@ no_irqs: pdata->pullups, pdata->pulldowns, ret); + ret = gpio_twl4030_debounce(pdata->debounce, pdata->mmc_cd); + if (ret) + dev_dbg(&pdev->dev, "debounce %.03x %.01x --> %d\n", + pdata->debounce, pdata->mmc_cd, + ret); + twl_gpiochip.base = pdata->gpio_base; twl_gpiochip.ngpio = TWL4030_GPIO_MAX; twl_gpiochip.dev = &pdev->dev; diff --git a/include/linux/i2c/twl4030.h b/include/linux/i2c/twl4030.h index a8f84c01f82..8137f660a5c 100644 --- a/include/linux/i2c/twl4030.h +++ b/include/linux/i2c/twl4030.h @@ -234,6 +234,9 @@ struct twl4030_gpio_platform_data { /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ u8 mmc_cd; + /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ + u32 debounce; + /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup * should be enabled. Else, if that bit is set in "pulldowns", * that pulldown is enabled. Don't waste power by letting any @@ -307,12 +310,6 @@ int twl4030_sih_setup(int module); #define TWL4030_VAUX3_DEV_GRP 0x1F #define TWL4030_VAUX3_DEDICATED 0x22 -/* - * Exported TWL4030 GPIO APIs - * - * WARNING -- use standard GPIO and IRQ calls instead; these will vanish. - */ -int twl4030_set_gpio_debounce(int gpio, int enable); #if defined(CONFIG_TWL4030_BCI_BATTERY) || \ defined(CONFIG_TWL4030_BCI_BATTERY_MODULE)