S: Beaverton, Oregon 97005
S: USA
-N: Li Yang
-E: leoli@freescale.com
-D: Freescale Highspeed USB device driver
-D: Freescale QE SoC support and Ethernet driver
-S: B-1206 Jingmao Guojigongyu
-S: 16 Baliqiao Nanjie, Beijing 101100
-S: People's Repulic of China
-
N: Marcelo Tosatti
E: marcelo@kvack.org
D: v2.4 kernel maintainer
S: New York, New York 10025
S: USA
+N: Li Yang
+E: leoli@freescale.com
+D: Freescale Highspeed USB device driver
+D: Freescale QE SoC support and Ethernet driver
+S: B-1206 Jingmao Guojigongyu
+S: 16 Baliqiao Nanjie, Beijing 101100
+S: People's Repulic of China
+
N: Victor Yodaiken
E: yodaiken@fsmlabs.com
D: RTLinux (RealTime Linux)
--- /dev/null
+ SM501 Driver
+ ============
+
+Copyright 2006, 2007 Simtec Electronics
+
+Core
+----
+
+The core driver in drivers/mfd provides common services for the
+drivers which manage the specific hardware blocks. These services
+include locking for common registers, clock control and resource
+management.
+
+The core registers drivers for both PCI and generic bus based
+chips via the platform device and driver system.
+
+On detection of a device, the core initialises the chip (which may
+be specified by the platform data) and then exports the selected
+peripheral set as platform devices for the specific drivers.
+
+The core re-uses the platform device system as the platform device
+system provides enough features to support the drivers without the
+need to create a new bus-type and the associated code to go with it.
+
+
+Resources
+---------
+
+Each peripheral has a view of the device which is implicitly narrowed to
+the specific set of resources that peripheral requires in order to
+function correctly.
+
+The centralised memory allocation allows the driver to ensure that the
+maximum possible resource allocation can be made to the video subsystem
+as this is by-far the most resource-sensitive of the on-chip functions.
+
+The primary issue with memory allocation is that of moving the video
+buffers once a display mode is chosen. Indeed when a video mode change
+occurs the memory footprint of the video subsystem changes.
+
+Since video memory is difficult to move without changing the display
+(unless sufficient contiguous memory can be provided for the old and new
+modes simultaneously) the video driver fully utilises the memory area
+given to it by aligning fb0 to the start of the area and fb1 to the end
+of it. Any memory left over in the middle is used for the acceleration
+functions, which are transient and thus their location is less critical
+as it can be moved.
+
+
+Configuration
+-------------
+
+The platform device driver uses a set of platform data to pass
+configurations through to the core and the subsidiary drivers
+so that there can be support for more than one system carrying
+an SM501 built into a single kernel image.
+
+The PCI driver assumes that the PCI card behaves as per the Silicon
+Motion reference design.
+
+There is an errata (AB-5) affecting the selection of the
+of the M1XCLK and M1CLK frequencies. These two clocks
+must be sourced from the same PLL, although they can then
+be divided down individually. If this is not set, then SM501 may
+lock and hang the whole system. The driver will refuse to
+attach if the PLL selection is different.
--- /dev/null
+Why the "volatile" type class should not be used
+------------------------------------------------
+
+C programmers have often taken volatile to mean that the variable could be
+changed outside of the current thread of execution; as a result, they are
+sometimes tempted to use it in kernel code when shared data structures are
+being used. In other words, they have been known to treat volatile types
+as a sort of easy atomic variable, which they are not. The use of volatile in
+kernel code is almost never correct; this document describes why.
+
+The key point to understand with regard to volatile is that its purpose is
+to suppress optimization, which is almost never what one really wants to
+do. In the kernel, one must protect shared data structures against
+unwanted concurrent access, which is very much a different task. The
+process of protecting against unwanted concurrency will also avoid almost
+all optimization-related problems in a more efficient way.
+
+Like volatile, the kernel primitives which make concurrent access to data
+safe (spinlocks, mutexes, memory barriers, etc.) are designed to prevent
+unwanted optimization. If they are being used properly, there will be no
+need to use volatile as well. If volatile is still necessary, there is
+almost certainly a bug in the code somewhere. In properly-written kernel
+code, volatile can only serve to slow things down.
+
+Consider a typical block of kernel code:
+
+ spin_lock(&the_lock);
+ do_something_on(&shared_data);
+ do_something_else_with(&shared_data);
+ spin_unlock(&the_lock);
+
+If all the code follows the locking rules, the value of shared_data cannot
+change unexpectedly while the_lock is held. Any other code which might
+want to play with that data will be waiting on the lock. The spinlock
+primitives act as memory barriers - they are explicitly written to do so -
+meaning that data accesses will not be optimized across them. So the
+compiler might think it knows what will be in shared_data, but the
+spin_lock() call, since it acts as a memory barrier, will force it to
+forget anything it knows. There will be no optimization problems with
+accesses to that data.
+
+If shared_data were declared volatile, the locking would still be
+necessary. But the compiler would also be prevented from optimizing access
+to shared_data _within_ the critical section, when we know that nobody else
+can be working with it. While the lock is held, shared_data is not
+volatile. When dealing with shared data, proper locking makes volatile
+unnecessary - and potentially harmful.
+
+The volatile storage class was originally meant for memory-mapped I/O
+registers. Within the kernel, register accesses, too, should be protected
+by locks, but one also does not want the compiler "optimizing" register
+accesses within a critical section. But, within the kernel, I/O memory
+accesses are always done through accessor functions; accessing I/O memory
+directly through pointers is frowned upon and does not work on all
+architectures. Those accessors are written to prevent unwanted
+optimization, so, once again, volatile is unnecessary.
+
+Another situation where one might be tempted to use volatile is
+when the processor is busy-waiting on the value of a variable. The right
+way to perform a busy wait is:
+
+ while (my_variable != what_i_want)
+ cpu_relax();
+
+The cpu_relax() call can lower CPU power consumption or yield to a
+hyperthreaded twin processor; it also happens to serve as a memory barrier,
+so, once again, volatile is unnecessary. Of course, busy-waiting is
+generally an anti-social act to begin with.
+
+There are still a few rare situations where volatile makes sense in the
+kernel:
+
+ - The above-mentioned accessor functions might use volatile on
+ architectures where direct I/O memory access does work. Essentially,
+ each accessor call becomes a little critical section on its own and
+ ensures that the access happens as expected by the programmer.
+
+ - Inline assembly code which changes memory, but which has no other
+ visible side effects, risks being deleted by GCC. Adding the volatile
+ keyword to asm statements will prevent this removal.
+
+ - The jiffies variable is special in that it can have a different value
+ every time it is referenced, but it can be read without any special
+ locking. So jiffies can be volatile, but the addition of other
+ variables of this type is strongly frowned upon. Jiffies is considered
+ to be a "stupid legacy" issue (Linus's words) in this regard; fixing it
+ would be more trouble than it is worth.
+
+ - Pointers to data structures in coherent memory which might be modified
+ by I/O devices can, sometimes, legitimately be volatile. A ring buffer
+ used by a network adapter, where that adapter changes pointers to
+ indicate which descriptors have been processed, is an example of this
+ type of situation.
+
+For most code, none of the above justifications for volatile apply. As a
+result, the use of volatile is likely to be seen as a bug and will bring
+additional scrutiny to the code. Developers who are tempted to use
+volatile should take a step back and think about what they are truly trying
+to accomplish.
+
+Patches to remove volatile variables are generally welcome - as long as
+they come with a justification which shows that the concurrency issues have
+been properly thought through.
+
+
+NOTES
+-----
+
+[1] http://lwn.net/Articles/233481/
+[2] http://lwn.net/Articles/233482/
+
+CREDITS
+-------
+
+Original impetus and research by Randy Dunlap
+Written by Jonathan Corbet
+Improvements via coments from Satyam Sharma, Johannes Stezenbach, Jesper
+ Juhl, Heikki Orsila, H. Peter Anvin, Philipp Hahn, and Stefan
+ Richter.
XFS FILESYSTEM
P: Silicon Graphics Inc
-P: Tim Shimmin, David Chatterton
+P: Tim Shimmin
M: xfs-masters@oss.sgi.com
L: xfs@oss.sgi.com
W: http://oss.sgi.com/projects/xfs
-T: git git://oss.sgi.com:8090/xfs/xfs-2.6
+T: git git://oss.sgi.com:8090/xfs/xfs-2.6.git
S: Supported
XILINX UARTLITE SERIAL DRIVER
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 22
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
NAME = Holy Dancing Manatees, Batman!
# *DOCUMENTATION*
* __u32 len,
* unsigned short proto,
* unsigned int csum);
+ *
+ * Misalignment handling (which costs 16 instructions / 8 cycles)
+ * added by Ivan Kokshaysky <ink@jurassic.park.msu.ru>
*/
.globl csum_ipv6_magic
csum_ipv6_magic:
.prologue 0
- ldq $0,0($16) # e0 : load src & dst addr words
+ ldq_u $0,0($16) # e0 : load src & dst addr words
zapnot $20,15,$20 # .. e1 : zero extend incoming csum
extqh $18,1,$4 # e0 : byte swap len & proto while we wait
- ldq $1,8($16) # .. e1 :
+ ldq_u $21,7($16) # .. e1 : handle misalignment
extbl $18,1,$5 # e0 :
- ldq $2,0($17) # .. e1 :
+ ldq_u $1,8($16) # .. e1 :
extbl $18,2,$6 # e0 :
- ldq $3,8($17) # .. e1 :
+ ldq_u $22,15($16) # .. e1 :
extbl $18,3,$18 # e0 :
+ ldq_u $2,0($17) # .. e1 :
sra $4,32,$4 # e0 :
+ ldq_u $23,7($17) # .. e1 :
+
+ extql $0,$16,$0 # e0 :
+ ldq_u $3,8($17) # .. e1 :
+ extqh $21,$16,$21 # e0 :
+ ldq_u $24,15($17) # .. e1 :
+
sll $5,16,$5 # e0 :
+ or $0,$21,$0 # .. e1 : 1st src word complete
+ extql $1,$16,$1 # e0 :
addq $20,$0,$20 # .. e1 : begin summing the words
- sll $6,8,$6 # e0 :
+ extqh $22,$16,$22 # e0 :
cmpult $20,$0,$0 # .. e1 :
- extwh $19,7,$7 # e0 :
- or $4,$18,$18 # .. e1 :
+ sll $6,8,$6 # e0 :
+ or $1,$22,$1 # .. e1 : 2nd src word complete
- extbl $19,1,$19 # e0 :
+ extql $2,$17,$2 # e0 :
+ or $4,$18,$18 # .. e1 :
+ extqh $23,$17,$23 # e0 :
or $5,$6,$5 # .. e1 :
- or $18,$5,$18 # e0 : len complete
- or $19,$7,$19 # .. e1 :
- sll $19,48,$19 # e0 :
+ extql $3,$17,$3 # e0 :
+ or $2,$23,$2 # .. e1 : 1st dst word complete
+ extqh $24,$17,$24 # e0 :
+ or $18,$5,$18 # .. e1 : len complete
+
+ extwh $19,7,$7 # e0 :
+ or $3,$24,$3 # .. e1 : 2nd dst word complete
+ extbl $19,1,$19 # e0 :
addq $20,$1,$20 # .. e1 :
- sra $19,32,$19 # e0 : proto complete
+
+ or $19,$7,$19 # e0 :
cmpult $20,$1,$1 # .. e1 :
+ sll $19,48,$19 # e0 :
+ nop # .. e0 :
- nop # e0 :
+ sra $19,32,$19 # e0 : proto complete
addq $20,$2,$20 # .. e1 :
cmpult $20,$2,$2 # e0 :
addq $20,$3,$20 # .. e1 :
extwl $0,2,$1 # e0 : fold 17-bit value
zapnot $0,3,$0 # .. e1 :
addq $0,$1,$0 # e0 :
- not $0,$0 # e1 : and complement.
+ not $0,$0 # .. e1 : and complement.
zapnot $0,3,$0 # e0 :
ret # .. e1 :
* add the 3 low ushorts together, generating a uint
* a final add of the 2 lower ushorts
* truncating the result.
+ *
+ * Misalignment handling added by Ivan Kokshaysky <ink@jurassic.park.msu.ru>
+ * The cost is 16 instructions (~8 cycles), including two extra loads which
+ * may cause additional delay in rare cases (load-load replay traps).
*/
.globl csum_ipv6_magic
csum_ipv6_magic:
.prologue 0
- ldq $0,0($16) # L : Latency: 3
+ ldq_u $0,0($16) # L : Latency: 3
inslh $18,7,$4 # U : 0000000000AABBCC
- ldq $1,8($16) # L : Latency: 3
+ ldq_u $1,8($16) # L : Latency: 3
sll $19,8,$7 # U : U L U L : 0x00000000 00aabb00
+ and $16,7,$6 # E : src misalignment
+ ldq_u $5,15($16) # L : Latency: 3
zapnot $20,15,$20 # U : zero extend incoming csum
- ldq $2,0($17) # L : Latency: 3
- sll $19,24,$19 # U : U L L U : 0x000000aa bb000000
+ ldq_u $2,0($17) # L : U L U L : Latency: 3
+
+ extql $0,$6,$0 # U :
+ extqh $1,$6,$22 # U :
+ ldq_u $3,8($17) # L : Latency: 3
+ sll $19,24,$19 # U : U U L U : 0x000000aa bb000000
+
+ cmoveq $6,$31,$22 # E : src aligned?
+ ldq_u $23,15($17) # L : Latency: 3
inswl $18,3,$18 # U : 000000CCDD000000
+ addl $19,$7,$19 # E : U L U L : <sign bits>bbaabb00
- ldq $3,8($17) # L : Latency: 3
- bis $18,$4,$18 # E : 000000CCDDAABBCC
- addl $19,$7,$19 # E : <sign bits>bbaabb00
- nop # E : U L U L
+ or $0,$22,$0 # E : 1st src word complete
+ extql $1,$6,$1 # U :
+ or $18,$4,$18 # E : 000000CCDDAABBCC
+ extqh $5,$6,$5 # U : L U L U
+ and $17,7,$6 # E : dst misalignment
+ extql $2,$6,$2 # U :
+ or $1,$5,$1 # E : 2nd src word complete
+ extqh $3,$6,$22 # U : L U L U :
+
+ cmoveq $6,$31,$22 # E : dst aligned?
+ extql $3,$6,$3 # U :
addq $20,$0,$20 # E : begin summing the words
+ extqh $23,$6,$23 # U : L U L U :
+
srl $18,16,$4 # U : 0000000000CCDDAA
+ or $2,$22,$2 # E : 1st dst word complete
zap $19,0x3,$19 # U : <sign bits>bbaa0000
- nop # E : L U U L
+ or $3,$23,$3 # E : U L U L : 2nd dst word complete
cmpult $20,$0,$0 # E :
addq $20,$1,$20 # E :
clk_put(pclk);
}
-struct platform_device *at32_usart_map[1];
-unsigned int at32_nr_usarts = 1;
-
void __init setup_board(void)
{
at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21-rc6
-# Thu Apr 12 16:35:07 2007
+# Linux kernel version: 2.6.22-rc5
+# Sat Jun 23 15:40:05 2007
#
CONFIG_AVR32=y
CONFIG_GENERIC_GPIO=y
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
# CONFIG_BASE_FULL is not set
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=1
-# CONFIG_SLOB is not set
#
# Loadable module support
#
# Bus options
#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=y
CONFIG_INET6_ESP=y
CONFIG_INET6_IPCOMP=y
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_HL=m
CONFIG_IP6_NF_RAW=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Misc devices
#
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_MACB=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
# CONFIG_I2C is not set
#
# SPI Protocol Masters
#
# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
#
# Multifunction device drivers
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc6
-# Fri Jan 26 13:12:59 2007
+# Linux kernel version: 2.6.22-rc5
+# Sat Jun 23 15:32:08 2007
#
CONFIG_AVR32=y
+CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_BUG=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
+# CONFIG_TASK_XACCT is not set
# CONFIG_UTS_NS is not set
CONFIG_AUDIT=y
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-# CONFIG_TASK_XACCT is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_ELF_CORE=y
# CONFIG_BASE_FULL is not set
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=1
-# CONFIG_SLOB is not set
#
# Loadable module support
CONFIG_CPU_AT32AP7000=y
CONFIG_BOARD_ATSTK1002=y
CONFIG_BOARD_ATSTK1000=y
+# CONFIG_BOARD_ATNGW100 is not set
CONFIG_LOADER_U_BOOT=y
+
+#
+# Atmel AVR32 AP options
+#
+# CONFIG_AP7000_32_BIT_SMC is not set
+CONFIG_AP7000_16_BIT_SMC=y
+# CONFIG_AP7000_8_BIT_SMC is not set
CONFIG_LOAD_ADDRESS=0x10000000
CONFIG_ENTRY_ADDRESS=0x90000000
CONFIG_PHYS_OFFSET=0x10000000
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
# CONFIG_OWNERSHIP_TRACE is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
#
# Bus options
#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
-# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# CONFIG_MD is not set
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
#
# Network device support
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
CONFIG_MACB=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
#
# Network File Systems
#
-# CONFIG_NFS_FS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
-# CONFIG_DEBUG_SLAB is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_FRAME_POINTER=y
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
# CONFIG_KPROBES is not set
#
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
#include <asm/io.h>
.flags = IORESOURCE_IRQ, \
}
+/* REVISIT these assume *every* device supports DMA, but several
+ * don't ... tc, smc, pio, rtc, watchdog, pwm, ps2, and more.
+ */
#define DEFINE_DEV(_name, _id) \
+static u64 _name##_id##_dma_mask = DMA_32BIT_MASK; \
static struct platform_device _name##_id##_device = { \
.name = #_name, \
.id = _id, \
+ .dev = { \
+ .dma_mask = &_name##_id##_dma_mask, \
+ .coherent_dma_mask = DMA_32BIT_MASK, \
+ }, \
.resource = _name##_id##_resource, \
.num_resources = ARRAY_SIZE(_name##_id##_resource), \
}
#define DEFINE_DEV_DATA(_name, _id) \
+static u64 _name##_id##_dma_mask = DMA_32BIT_MASK; \
static struct platform_device _name##_id##_device = { \
.name = #_name, \
.id = _id, \
.dev = { \
+ .dma_mask = &_name##_id##_dma_mask, \
.platform_data = &_name##_id##_data, \
+ .coherent_dma_mask = DMA_32BIT_MASK, \
}, \
.resource = _name##_id##_resource, \
.num_resources = ARRAY_SIZE(_name##_id##_resource), \
void invalidate_dcache_region(void *start, size_t size)
{
unsigned long v, begin, end, linesz, mask;
- int flush = 0;
linesz = boot_cpu_data.dcache.linesz;
mask = linesz - 1;
* instead of invalidating ... never discard valid data!
*/
begin = (unsigned long)start;
- end = begin + size - 1;
+ end = begin + size;
if (begin & mask) {
flush_dcache_line(start);
begin += linesz;
- flush = 1;
}
- if ((end & mask) != mask) {
+ if (end & mask) {
flush_dcache_line((void *)end);
- end -= linesz;
- flush = 1;
+ end &= ~mask;
}
/* remaining cachelines only need invalidation */
- for (v = begin; v <= end; v += linesz)
+ for (v = begin; v < end; v += linesz)
invalidate_dcache_line((void *)v);
- if (flush)
- flush_write_buffer();
+ flush_write_buffer();
}
void clean_dcache_region(void *start, size_t size)
printk(KERN_INFO "Memory map:\n"
KERN_INFO " text = 0x%p-0x%p\n"
- KERN_INFO " init = 0x%p-0x%p\n"
+ KERN_INFO " rodata = 0x%p-0x%p\n"
KERN_INFO " data = 0x%p-0x%p\n"
- KERN_INFO " stack = 0x%p-0x%p\n"
+ KERN_INFO " stack = 0x%p-0x%p\n"
+ KERN_INFO " init = 0x%p-0x%p\n"
KERN_INFO " bss = 0x%p-0x%p\n"
KERN_INFO " available = 0x%p-0x%p\n"
#ifdef CONFIG_MTD_UCLINUX
KERN_INFO " DMA Zone = 0x%p-0x%p\n"
#endif
, _stext, _etext,
- __init_begin, __init_end,
+ __start_rodata, __end_rodata,
_sdata, _edata,
(void*)&init_thread_union, (void*)((int)(&init_thread_union) + 0x2000),
+ __init_begin, __init_end,
__bss_start, __bss_stop,
(void*)_ramstart, (void*)memory_end
#ifdef CONFIG_MTD_UCLINUX
unsigned long trapnr = fp->seqstat & SEQSTAT_EXCAUSE;
#ifdef CONFIG_KGDB
-# define CHK_DEBUGGER_TRAP() do { CHK_DEBUGGER(trapnr, sig, info.si_code, fp,); } while (0)
-# define CHK_DEBUGGER_TRAP_MAYBE() do { if (kgdb_connected) CHK_DEBUGGER_TRAP(); } while (0)
+# define CHK_DEBUGGER_TRAP() \
+ do { \
+ CHK_DEBUGGER(trapnr, sig, info.si_code, fp); \
+ } while (0)
+# define CHK_DEBUGGER_TRAP_MAYBE() \
+ do { \
+ if (kgdb_connected) \
+ CHK_DEBUGGER_TRAP(); \
+ } while (0)
#else
# define CHK_DEBUGGER_TRAP() do { } while (0)
# define CHK_DEBUGGER_TRAP_MAYBE() do { } while (0)
info.si_code = ILL_CPLB_MULHIT;
#ifdef CONFIG_DEBUG_HUNT_FOR_ZERO
sig = SIGSEGV;
- printk(KERN_EMERG "\n\nNULL pointer access (probably)\n");
+ printk(KERN_EMERG "\n"
+ KERN_EMERG "NULL pointer access (probably)\n");
#else
sig = SIGILL;
printk(KERN_EMERG EXC_0x27);
if (current->mm) {
fp->pc = current->mm->start_code;
} else {
- printk(KERN_EMERG "I can't return to memory that doesn't exist - bad things happen\n");
+ printk(KERN_EMERG
+ "I can't return to memory that doesn't exist"
+ " - bad things happen\n");
panic("Help - I've fallen and can't get up\n");
}
}
void dump_bfin_regs(struct pt_regs *fp, void *retaddr)
{
if (current->pid) {
- printk("\nCURRENT PROCESS:\n\n");
- printk("COMM=%s PID=%d\n", current->comm, current->pid);
+ printk(KERN_EMERG "\n" KERN_EMERG "CURRENT PROCESS:\n"
+ KERN_EMERG "\n");
+ printk(KERN_EMERG "COMM=%s PID=%d\n",
+ current->comm, current->pid);
} else {
printk
- ("\nNo Valid pid - Either things are really messed up, or you are in the kernel\n");
+ (KERN_EMERG "\n" KERN_EMERG
+ "No Valid pid - Either things are really messed up,"
+ " or you are in the kernel\n");
}
if (current->mm) {
- printk("TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
+ printk(KERN_EMERG "TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
"BSS = 0x%p-0x%p USER-STACK = 0x%p\n\n",
(void*)current->mm->start_code,
(void*)current->mm->end_code,
(void*)current->mm->start_stack);
}
- printk("return address: 0x%p; contents of [PC-16...PC+8]:\n", retaddr);
+ printk(KERN_EMERG "return address: [0x%p]; contents of:", retaddr);
if (retaddr != 0 && retaddr <= (void*)physical_mem_end
#if L1_CODE_LENGTH != 0
/* FIXME: Copy the code out of L1 Instruction SRAM through dma
&& retaddr < (void*)(L1_CODE_START + L1_CODE_LENGTH))
#endif
) {
- int i = 0;
+ int i = ((unsigned int)retaddr & 0xFFFFFFF0) - 32;
unsigned short x = 0;
- for (i = -16; i < 8; i++) {
- if (get_user(x, (unsigned short *)retaddr + i))
+ for (; i < ((unsigned int)retaddr & 0xFFFFFFF0 ) + 32 ;
+ i += 2) {
+ if ( !(i & 0xF) )
+ printk(KERN_EMERG "\n" KERN_EMERG
+ "0x%08x: ", i);
+
+ if (get_user(x, (unsigned short *)i))
break;
#ifndef CONFIG_DEBUG_HWERR
/* If one of the last few instructions was a STI
* and we just noticed
*/
if (x >= 0x0040 && x <= 0x0047 && i <= 0)
- panic("\n\nWARNING : You should reconfigure the kernel to turn on\n"
- " 'Hardware error interrupt debugging'\n"
- " The rest of this error is meanless\n");
+ panic("\n\nWARNING : You should reconfigure"
+ " the kernel to turn on\n"
+ " 'Hardware error interrupt"
+ " debugging'\n"
+ " The rest of this error"
+ " is meanless\n");
#endif
-
- if (i == -8)
- printk("\n");
- if (i == 0)
- printk("X\n");
- printk("%04x ", x);
+ if ( i == (unsigned int)retaddr )
+ printk("[%04x]", x);
+ else
+ printk(" %04x ", x);
}
+ printk("\n" KERN_EMERG "\n");
} else
- printk("Cannot look at the [PC] for it is in unreadable L1 SRAM - sorry\n");
-
- printk("\n\n");
-
- printk("RETE: %08lx RETN: %08lx RETX: %08lx RETS: %08lx\n",
- fp->rete, fp->retn, fp->retx, fp->rets);
- printk("IPEND: %04lx SYSCFG: %04lx\n", fp->ipend, fp->syscfg);
- printk("SEQSTAT: %08lx SP: %08lx\n", (long)fp->seqstat, (long)fp);
- printk("R0: %08lx R1: %08lx R2: %08lx R3: %08lx\n",
- fp->r0, fp->r1, fp->r2, fp->r3);
- printk("R4: %08lx R5: %08lx R6: %08lx R7: %08lx\n",
- fp->r4, fp->r5, fp->r6, fp->r7);
- printk("P0: %08lx P1: %08lx P2: %08lx P3: %08lx\n",
- fp->p0, fp->p1, fp->p2, fp->p3);
- printk("P4: %08lx P5: %08lx FP: %08lx\n", fp->p4, fp->p5, fp->fp);
- printk("A0.w: %08lx A0.x: %08lx A1.w: %08lx A1.x: %08lx\n",
- fp->a0w, fp->a0x, fp->a1w, fp->a1x);
-
- printk("LB0: %08lx LT0: %08lx LC0: %08lx\n", fp->lb0, fp->lt0,
- fp->lc0);
- printk("LB1: %08lx LT1: %08lx LC1: %08lx\n", fp->lb1, fp->lt1,
- fp->lc1);
- printk("B0: %08lx L0: %08lx M0: %08lx I0: %08lx\n", fp->b0, fp->l0,
- fp->m0, fp->i0);
- printk("B1: %08lx L1: %08lx M1: %08lx I1: %08lx\n", fp->b1, fp->l1,
- fp->m1, fp->i1);
- printk("B2: %08lx L2: %08lx M2: %08lx I2: %08lx\n", fp->b2, fp->l2,
- fp->m2, fp->i2);
- printk("B3: %08lx L3: %08lx M3: %08lx I3: %08lx\n", fp->b3, fp->l3,
- fp->m3, fp->i3);
-
- printk("\nUSP: %08lx ASTAT: %08lx\n", rdusp(), fp->astat);
+ printk(KERN_EMERG
+ "Cannot look at the [PC] for it is"
+ "in unreadable L1 SRAM - sorry\n");
+
+
+ printk(KERN_EMERG
+ "RETE: %08lx RETN: %08lx RETX: %08lx RETS: %08lx\n",
+ fp->rete, fp->retn, fp->retx, fp->rets);
+ printk(KERN_EMERG "IPEND: %04lx SYSCFG: %04lx\n",
+ fp->ipend, fp->syscfg);
+ printk(KERN_EMERG "SEQSTAT: %08lx SP: %08lx\n",
+ (long)fp->seqstat, (long)fp);
+ printk(KERN_EMERG "R0: %08lx R1: %08lx R2: %08lx R3: %08lx\n",
+ fp->r0, fp->r1, fp->r2, fp->r3);
+ printk(KERN_EMERG "R4: %08lx R5: %08lx R6: %08lx R7: %08lx\n",
+ fp->r4, fp->r5, fp->r6, fp->r7);
+ printk(KERN_EMERG "P0: %08lx P1: %08lx P2: %08lx P3: %08lx\n",
+ fp->p0, fp->p1, fp->p2, fp->p3);
+ printk(KERN_EMERG
+ "P4: %08lx P5: %08lx FP: %08lx\n",
+ fp->p4, fp->p5, fp->fp);
+ printk(KERN_EMERG
+ "A0.w: %08lx A0.x: %08lx A1.w: %08lx A1.x: %08lx\n",
+ fp->a0w, fp->a0x, fp->a1w, fp->a1x);
+
+ printk(KERN_EMERG "LB0: %08lx LT0: %08lx LC0: %08lx\n",
+ fp->lb0, fp->lt0, fp->lc0);
+ printk(KERN_EMERG "LB1: %08lx LT1: %08lx LC1: %08lx\n",
+ fp->lb1, fp->lt1, fp->lc1);
+ printk(KERN_EMERG "B0: %08lx L0: %08lx M0: %08lx I0: %08lx\n",
+ fp->b0, fp->l0, fp->m0, fp->i0);
+ printk(KERN_EMERG "B1: %08lx L1: %08lx M1: %08lx I1: %08lx\n",
+ fp->b1, fp->l1, fp->m1, fp->i1);
+ printk(KERN_EMERG "B2: %08lx L2: %08lx M2: %08lx I2: %08lx\n",
+ fp->b2, fp->l2, fp->m2, fp->i2);
+ printk(KERN_EMERG "B3: %08lx L3: %08lx M3: %08lx I3: %08lx\n",
+ fp->b3, fp->l3, fp->m3, fp->i3);
+
+ printk(KERN_EMERG "\n" KERN_EMERG "USP: %08lx ASTAT: %08lx\n",
+ rdusp(), fp->astat);
if ((long)fp->seqstat & SEQSTAT_EXCAUSE) {
- printk(KERN_EMERG "DCPLB_FAULT_ADDR=%p\n", (void*)bfin_read_DCPLB_FAULT_ADDR());
- printk(KERN_EMERG "ICPLB_FAULT_ADDR=%p\n", (void*)bfin_read_ICPLB_FAULT_ADDR());
+ printk(KERN_EMERG "DCPLB_FAULT_ADDR=%p\n",
+ (void *)bfin_read_DCPLB_FAULT_ADDR());
+ printk(KERN_EMERG "ICPLB_FAULT_ADDR=%p\n",
+ (void *)bfin_read_ICPLB_FAULT_ADDR());
}
printk("\n\n");
LSETUP (.Lquad_loop_s, .Lquad_loop_e) LC0=P1;
.Lquad_loop_s:
+#ifdef ANOMALY_05000202
+ R0 = [P0++];
+ R1 = [I0++];
+#else
MNOP || R0 = [P0++] || R1 = [I0++];
+#endif
CC = R0 == R1;
IF !CC JUMP .Lquad_different;
.Lquad_loop_e:
.Lmore_than_seven:
/* There's at least eight bytes to copy. */
P2 += -1; /* because we unroll one iteration */
- LSETUP(.Lword_loop, .Lword_loop) LC0=P2;
+ LSETUP(.Lword_loops, .Lword_loope) LC0=P2;
R0 = R1;
I1 = P1;
R3 = [I1++];
-.Lword_loop:
+#ifdef ANOMALY_05000202
+.Lword_loops:
+ [P0++] = R3;
+.Lword_loope:
+ R3 = [I1++];
+#else
+.Lword_loops:
+.Lword_loope:
MNOP || [P0++] = R3 || R3 = [I1++];
-
+#endif
[P0++] = R3;
/* Any remaining bytes to copy? */
R3 = 0x3;
P2 = R2; /* set remainder */
R1 = [I0++];
- LSETUP (.Lquad_loop, .Lquad_loop) LC0=P1;
-.Lquad_loop: MNOP || [P0++] = R1 || R1 = [I0++];
+ LSETUP (.Lquad_loops, .Lquad_loope) LC0=P1;
+#ifdef ANOMALY_05000202
+.Lquad_loops:
+ [P0++] = R1;
+.Lquad_loope:
+ R1 = [I0++];
+#else
+.Lquad_loops:
+.Lquad_loope:
+ MNOP || [P0++] = R1 || R1 = [I0++];
+#endif
[P0++] = R1;
CC = P2 == 0; /* any remaining bytes? */
R1 = B[P3--] (Z);
CC = P2 == 0;
IF CC JUMP .Lno_loop;
+#ifdef ANOMALY_05000245
+ NOP;
+ NOP;
+#endif
LSETUP (.Lol_s, .Lol_e) LC0 = P2;
.Lol_s: B[P0--] = R1;
.Lol_e: R1 = B[P3--] (Z);
R2 = R0 & R2;
P0 = R2;
P1 = R1;
- CSYNC;
+ CSYNC(R3);
IFLUSH [P0];
1:
IFLUSH [P0++];
CC = P0 < P1 (iu);
IF CC JUMP 1b (bp);
IFLUSH [P0];
- SSYNC;
+ SSYNC(R3);
RTS;
ENDPROC(_blackfin_icache_flush_range)
R2 = R0 & R2;
P0 = R2;
P1 = R1;
- CSYNC;
+ CSYNC(R3);
IFLUSH [P0];
1:
FLUSH [P0];
IF CC JUMP 1b (bp);
IFLUSH [P0];
FLUSH [P0];
- SSYNC;
+ SSYNC(R3);
RTS;
ENDPROC(_blackfin_icache_dcache_flush_range)
R2 = R0 & R2;
P0 = R2;
P1 = R1;
- CSYNC;
+ CSYNC(R3);
FLUSHINV[P0];
1:
FLUSHINV[P0++];
* so do one more.
*/
FLUSHINV[P0];
- SSYNC;
+ SSYNC(R3);
RTS;
ENDPROC(_blackfin_dcache_invalidate_range)
R2 = R0 & R2;
P0 = R2;
P1 = R1;
- CSYNC;
+ CSYNC(R3);
FLUSH[P0];
1:
FLUSH[P0++];
* one more.
*/
FLUSH[P0];
- SSYNC;
+ SSYNC(R3);
RTS;
ENDPROC(_blackfin_dcache_flush_range)
ENTRY(_blackfin_dflush_page)
P1 = 1 << (PAGE_SHIFT - L1_CACHE_SHIFT);
P0 = R0;
- CSYNC;
+ CSYNC(R3);
FLUSH[P0];
LSETUP (.Lfl1, .Lfl1) LC0 = P1;
.Lfl1: FLUSH [P0++];
- SSYNC;
+ SSYNC(R3);
RTS;
ENDPROC(_blackfin_dflush_page)
fp = 0;
#endif
-#ifdef ANOMALY_05000283
+#if defined (ANOMALY_05000283) || defined (ANOMALY_05000315)
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
config HIGHMEM64G
bool "64GB"
- depends on X86_CMPXCHG64
+ depends on !M386 && !M486
help
Select this if you have a 32-bit processor and more than 4
gigabytes of physical RAM.
config X86_CMPXCHG64
bool
- depends on !M386 && !M486
+ depends on X86_PAE
default y
config X86_ALIGNMENT_16
#
ENTRY(acpi_copy_wakeup_routine)
+ pushl %ebx
sgdt saved_gdt
sidt saved_idt
sldt saved_ldt
movl %edx, video_flags - wakeup_start (%eax)
movl $0x12345678, real_magic - wakeup_start (%eax)
movl $0x12345678, saved_magic
+ popl %ebx
ret
save_registers:
module_param_named(show, mtrr_show, bool, 0);
/* Get the MSR pair relating to a var range */
-static void __init
+static void
get_mtrr_var_range(unsigned int index, struct mtrr_var_range *vr)
{
rdmsr(MTRRphysBase_MSR(index), vr->base_lo, vr->base_hi);
get_fixed_ranges(mtrr_state.fixed_ranges);
}
-static void __cpuinit print_fixed(unsigned base, unsigned step, const mtrr_type*types)
+static void print_fixed(unsigned base, unsigned step, const mtrr_type*types)
{
unsigned i;
* initialized (i.e. before smp_init()).
*
*/
-void mtrr_bp_init(void)
+__init void mtrr_bp_init(void)
{
init_ifs();
#include <linux/string.h>
#include <linux/pci.h>
#include <linux/module.h>
+#include <linux/pci.h>
#include <asm/io.h>
struct dma_coherent_mem {
return mem->virt_base + (pos << PAGE_SHIFT);
}
EXPORT_SYMBOL(dma_mark_declared_memory_occupied);
+
+#ifdef CONFIG_PCI
+/* Many VIA bridges seem to corrupt data for DAC. Disable it here */
+
+int forbid_dac;
+EXPORT_SYMBOL(forbid_dac);
+
+static __devinit void via_no_dac(struct pci_dev *dev)
+{
+ if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI && forbid_dac == 0) {
+ printk(KERN_INFO "PCI: VIA PCI bridge detected. Disabling DAC.\n");
+ forbid_dac = 1;
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_ANY_ID, via_no_dac);
+
+static int check_iommu(char *s)
+{
+ if (!strcmp(s, "usedac")) {
+ forbid_dac = -1;
+ return 1;
+ }
+ return 0;
+}
+__setup("iommu=", check_iommu);
+#endif
unsigned long start = PFN_ALIGN(_text);
unsigned long size = PFN_ALIGN(_etext) - start;
+#ifndef CONFIG_KPROBES
#ifdef CONFIG_HOTPLUG_CPU
/* It must still be possible to apply SMP alternatives. */
if (num_possible_cpus() <= 1)
size >> PAGE_SHIFT, PAGE_KERNEL_RX);
printk("Write protecting the kernel text: %luk\n", size >> 10);
}
-
+#endif
start += size;
size = (unsigned long)__end_rodata - start;
change_page_attr(virt_to_page(start),
return base;
}
-static void flush_kernel_map(void *arg)
+static void cache_flush_page(struct page *p)
{
- unsigned long adr = (unsigned long)arg;
+ unsigned long adr = (unsigned long)page_address(p);
+ int i;
+ for (i = 0; i < PAGE_SIZE; i += boot_cpu_data.x86_clflush_size)
+ asm volatile("clflush (%0)" :: "r" (adr + i));
+}
+
+static void flush_kernel_map(void *arg)
+{
+ struct list_head *lh = (struct list_head *)arg;
+ struct page *p;
- if (adr && cpu_has_clflush) {
- int i;
- for (i = 0; i < PAGE_SIZE; i += boot_cpu_data.x86_clflush_size)
- asm volatile("clflush (%0)" :: "r" (adr + i));
+ /* High level code is not ready for clflush yet */
+ if (0 && cpu_has_clflush) {
+ list_for_each_entry (p, lh, lru)
+ cache_flush_page(p);
} else if (boot_cpu_data.x86_model >= 4)
wbinvd();
return 0;
}
-static inline void flush_map(void *adr)
+static inline void flush_map(struct list_head *l)
{
- on_each_cpu(flush_kernel_map, adr, 1, 1);
+ on_each_cpu(flush_kernel_map, l, 1, 1);
}
/*
spin_lock_irq(&cpa_lock);
list_replace_init(&df_list, &l);
spin_unlock_irq(&cpa_lock);
- if (!cpu_has_clflush)
- flush_map(NULL);
+ flush_map(&l);
list_for_each_entry_safe(pg, next, &l, lru) {
- if (cpu_has_clflush)
- flush_map(page_address(pg));
__free_page(pg);
}
}
help
Say Y here to report ST-RAM usage statistics in /proc/stram.
-config ATARI_KBD_CORE
- bool
-
config HEARTBEAT
bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40
default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300
select SYS_SUPPORTS_LITTLE_ENDIAN
config PNX8550_STB810
- bool "Support for Philips PNX8550 based STB810 board"
+ bool "Philips PNX8550 based STB810 board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
can be found at http://www.linux-mips.org/wiki/Qemu.
config MARKEINS
- bool "Support for NEC EMMA2RH Mark-eins"
+ bool "NEC EMMA2RH Mark-eins"
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
depends on SYS_SUPPORTS_MULTITHREADING
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
+ select CPU_MIPSR2_SRS
select MIPS_MT
help
Includes a loader for loading an elf relocatable object
prom_argc = fw_arg0;
prom_argv = (char **) fw_arg1;
- prom_envp = (int *) fw_arg3;
+ prom_envp = (char **) fw_arg3;
mips_machgroup = MACH_GROUP_ALCHEMY;
mips_machtype = MACH_PB1100;
au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
}
/* Put the clock in BCD mode */
- if (readl(0xac00002C) & 0x4) { /* reg B */
+ if (au_readl(0xac00002C) & 0x4) { /* reg B */
au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
au_sync();
}
.mem_resource = &cobalt_mem_resource,
.io_resource = &cobalt_io_resource,
.io_offset = 0 - GT_DEF_PCI0_IO_BASE,
+ .io_map_base = CKSEG1ADDR(GT_DEF_PCI0_IO_BASE),
};
static int __init cobalt_pci_init(void)
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_RTC=m
-CONFIG_GEN_RTC=m
-CONFIG_GEN_RTC_X=y
+# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
case CPU_4KEC:
case CPU_4KSC:
case CPU_5KC:
-/* case CPU_20KC:*/
case CPU_24K:
case CPU_25KF:
case CPU_34K:
if (allow_au1k_wait)
cpu_wait = au1k_wait;
break;
+ case CPU_20KC:
+ /*
+ * WAIT on Rev1.0 has E1, E2, E3 and E16.
+ * WAIT on Rev2.0 and Rev3.0 has E16.
+ * Rev3.1 WAIT is nop, why bother
+ */
+ if ((c->processor_id & 0xff) <= 0x64)
+ break;
+
+ cpu_wait = r4k_wait;
+ break;
case CPU_RM9000:
if ((c->processor_id & 0x00ff) >= 0x40)
cpu_wait = r4k_wait;
#include "signal-common.h"
-#define SI_PAD_SIZE32 ((SI_MAX_SIZE/sizeof(int)) - 3)
-
-typedef struct compat_siginfo {
- int si_signo;
- int si_code;
- int si_errno;
-
- union {
- int _pad[SI_PAD_SIZE32];
-
- /* kill() */
- struct {
- compat_pid_t _pid; /* sender's pid */
- compat_uid_t _uid; /* sender's uid */
- } _kill;
-
- /* SIGCHLD */
- struct {
- compat_pid_t _pid; /* which child */
- compat_uid_t _uid; /* sender's uid */
- int _status; /* exit code */
- compat_clock_t _utime;
- compat_clock_t _stime;
- } _sigchld;
-
- /* IRIX SIGCHLD */
- struct {
- compat_pid_t _pid; /* which child */
- compat_clock_t _utime;
- int _status; /* exit code */
- compat_clock_t _stime;
- } _irix_sigchld;
-
- /* SIGILL, SIGFPE, SIGSEGV, SIGBUS */
- struct {
- s32 _addr; /* faulting insn/memory ref. */
- } _sigfault;
-
- /* SIGPOLL, SIGXFSZ (To do ...) */
- struct {
- int _band; /* POLL_IN, POLL_OUT, POLL_MSG */
- int _fd;
- } _sigpoll;
-
- /* POSIX.1b timers */
- struct {
- timer_t _tid; /* timer id */
- int _overrun; /* overrun count */
- compat_sigval_t _sigval;/* same as below */
- int _sys_private; /* not to be passed to user */
- } _timer;
-
- /* POSIX.1b signals */
- struct {
- compat_pid_t _pid; /* sender's pid */
- compat_uid_t _uid; /* sender's uid */
- compat_sigval_t _sigval;
- } _rt;
-
- } _sifields;
-} compat_siginfo_t;
-
/*
* Including <asm/unistd.h> would give use the 64-bit syscall numbers ...
*/
struct rt_sigframe_n32 {
u32 rs_ass[4]; /* argument save space for o32 */
u32 rs_code[2]; /* signal trampoline */
- struct siginfo rs_info;
+ struct compat_siginfo rs_info;
struct ucontextn32 rs_uc;
};
struct rt_sigframe_n32 {
u32 rs_ass[4]; /* argument save space for o32 */
u32 rs_pad[2];
- struct siginfo rs_info;
+ struct compat_siginfo rs_info;
struct ucontextn32 rs_uc;
u32 rs_code[8] ____cacheline_aligned; /* signal trampoline */
};
install_sigtramp(frame->rs_code, __NR_N32_rt_sigreturn);
/* Create siginfo. */
- err |= copy_siginfo_to_user(&frame->rs_info, info);
+ err |= copy_siginfo_to_user32(&frame->rs_info, info);
/* Create the ucontext. */
err |= __put_user(0, &frame->rs_uc.uc_flags);
#include <asm/system.h>
#include <asm/hardirq.h>
#include <asm/hazards.h>
+#include <asm/irq.h>
#include <asm/mmu_context.h>
#include <asm/smp.h>
-#include <asm/mips-boards/maltaint.h>
#include <asm/mipsregs.h>
#include <asm/cacheflush.h>
#include <asm/time.h>
#ifdef CONFIG_SMTC_IDLE_HOOK_DEBUG
unsigned int vpe = current_cpu_data.vpe_id;
- vpemask[vpe][irq - MIPSCPU_INT_BASE] = 1;
+ vpemask[vpe][irq - MIPS_CPU_IRQ_BASE] = 1;
#endif
irq_hwmask[irq] = hwmask;
switch (type_copy) {
case SMTC_CLOCK_TICK:
irq_enter();
- kstat_this_cpu.irqs[MIPSCPU_INT_BASE + MIPSCPU_INT_CPUCTR]++;
+ kstat_this_cpu.irqs[MIPS_CPU_IRQ_BASE + cp0_compare_irq]++;
/* Invoke Clock "Interrupt" */
ipi_timer_latch[dest_copy] = 0;
#ifdef CONFIG_SMTC_IDLE_HOOK_DEBUG
EXPORT_SYMBOL(null_perf_irq);
EXPORT_SYMBOL(perf_irq);
+/*
+ * Timer interrupt
+ */
+int cp0_compare_irq;
+
/*
* Performance counter IRQ or -1 if shared with timer
*/
-int mipsxx_perfcount_irq;
-EXPORT_SYMBOL(mipsxx_perfcount_irq);
+int cp0_perfcount_irq;
+EXPORT_SYMBOL_GPL(cp0_perfcount_irq);
/*
* Possibly handle a performance counter interrupt.
{
/*
* The performance counter overflow interrupt may be shared with the
- * timer interrupt (mipsxx_perfcount_irq < 0). If it is and a
+ * timer interrupt (cp0_perfcount_irq < 0). If it is and a
* performance counter has overflowed (perf_irq() == IRQ_HANDLED)
* and we can't reliably determine if a counter interrupt has also
* happened (!r2) then don't check for a timer interrupt.
*/
- return (mipsxx_perfcount_irq < 0) &&
+ return (cp0_perfcount_irq < 0) &&
perf_irq() == IRQ_HANDLED &&
!r2;
}
if (!secondaryTC) {
#endif /* CONFIG_MIPS_MT_SMTC */
- /*
- * Interrupt handling.
- */
if (cpu_has_veic || cpu_has_vint) {
write_c0_ebase (ebase);
/* Setting vector spacing enables EI/VI mode */
} else
set_c0_cause(CAUSEF_IV);
}
+
+ /*
+ * Before R2 both interrupt numbers were fixed to 7, so on R2 only:
+ *
+ * o read IntCtl.IPTI to determine the timer interrupt
+ * o read IntCtl.IPPCI to determine the performance counter interrupt
+ */
+ if (cpu_has_mips_r2) {
+ cp0_compare_irq = (read_c0_intctl () >> 29) & 7;
+ cp0_perfcount_irq = -1;
+ } else {
+ cp0_compare_irq = CP0_LEGACY_COMPARE_IRQ;
+ cp0_perfcount_irq = (read_c0_intctl () >> 26) & 7;
+ if (cp0_perfcount_irq != cp0_compare_irq)
+ cp0_perfcount_irq = -1;
+ }
+
#ifdef CONFIG_MIPS_MT_SMTC
}
#endif /* CONFIG_MIPS_MT_SMTC */
#include "libgcc.h"
-word_type __ucmpdi2 (unsigned long a, unsigned long b)
+word_type __ucmpdi2 (unsigned long long a, unsigned long long b)
{
const DWunion au = {.ll = a};
const DWunion bu = {.ll = b};
if (irq == MIPSCPU_INT_ATLAS)
atlas_hw0_irqdispatch();
else if (irq >= 0)
- do_IRQ(MIPSCPU_INT_BASE + irq);
+ do_IRQ(MIPS_CPU_IRQ_BASE + irq);
else
spurious_interrupt();
}
} else if (cpu_has_vint) {
set_vi_handler (MIPSCPU_INT_ATLAS, atlas_hw0_irqdispatch);
#ifdef CONFIG_MIPS_MT_SMTC
- setup_irq_smtc (MIPSCPU_INT_BASE + MIPSCPU_INT_ATLAS,
+ setup_irq_smtc (MIPS_CPU_IRQ_BASE + MIPSCPU_INT_ATLAS,
&atlasirq, (0x100 << MIPSCPU_INT_ATLAS));
#else /* Not SMTC */
- setup_irq(MIPSCPU_INT_BASE + MIPSCPU_INT_ATLAS, &atlasirq);
+ setup_irq(MIPS_CPU_IRQ_BASE + MIPSCPU_INT_ATLAS, &atlasirq);
#endif /* CONFIG_MIPS_MT_SMTC */
} else
- setup_irq(MIPSCPU_INT_BASE + MIPSCPU_INT_ATLAS, &atlasirq);
+ setup_irq(MIPS_CPU_IRQ_BASE + MIPSCPU_INT_ATLAS, &atlasirq);
}
unsigned long cpu_khz;
static int mips_cpu_timer_irq;
-extern int mipsxx_perfcount_irq;
+extern int cp0_perfcount_irq;
extern void smtc_timer_broadcast(int);
static void mips_timer_dispatch(void)
static void mips_perf_dispatch(void)
{
- do_IRQ(mipsxx_perfcount_irq);
+ do_IRQ(cp0_perfcount_irq);
}
/*
{
/*
* The performance counter overflow interrupt may be shared with the
- * timer interrupt (mipsxx_perfcount_irq < 0). If it is and a
+ * timer interrupt (cp0_perfcount_irq < 0). If it is and a
* performance counter has overflowed (perf_irq() == IRQ_HANDLED)
* and we can't reliably determine if a counter interrupt has also
* happened (!r2) then don't check for a timer interrupt.
*/
- return (mipsxx_perfcount_irq < 0) &&
+ return (cp0_perfcount_irq < 0) &&
perf_irq() == IRQ_HANDLED &&
!r2;
}
void __init plat_perf_setup(struct irqaction *irq)
{
- int hwint = 0;
- mipsxx_perfcount_irq = -1;
+ cp0_perfcount_irq = -1;
#ifdef MSC01E_INT_BASE
if (cpu_has_veic) {
set_vi_handler (MSC01E_INT_PERFCTR, mips_perf_dispatch);
- mipsxx_perfcount_irq = MSC01E_INT_BASE + MSC01E_INT_PERFCTR;
+ cp0_perfcount_irq = MSC01E_INT_BASE + MSC01E_INT_PERFCTR;
} else
#endif
- if (cpu_has_mips_r2) {
- /*
- * Read IntCtl.IPPCI to determine the performance
- * counter interrupt
- */
- hwint = (read_c0_intctl () >> 26) & 7;
- if (hwint != MIPSCPU_INT_CPUCTR) {
- if (cpu_has_vint)
- set_vi_handler (hwint, mips_perf_dispatch);
- mipsxx_perfcount_irq = MIPSCPU_INT_BASE + hwint;
- }
- }
- if (mipsxx_perfcount_irq >= 0) {
+ if (cp0_perfcount_irq >= 0) {
+ if (cpu_has_vint)
+ set_vi_handler(cp0_perfcount_irq, mips_perf_dispatch);
#ifdef CONFIG_MIPS_MT_SMTC
- setup_irq_smtc(mipsxx_perfcount_irq, irq, 0x100 << hwint);
+ setup_irq_smtc(cp0_perfcount_irq, irq,
+ 0x100 << cp0_perfcount_irq);
#else
- setup_irq(mipsxx_perfcount_irq, irq);
+ setup_irq(cp0_perfcount_irq, irq);
#endif /* CONFIG_MIPS_MT_SMTC */
#ifdef CONFIG_SMP
- set_irq_handler(mipsxx_perfcount_irq, handle_percpu_irq);
+ set_irq_handler(cp0_perfcount_irq, handle_percpu_irq);
#endif
}
}
void __init plat_timer_setup(struct irqaction *irq)
{
- int hwint = 0;
#ifdef MSC01E_INT_BASE
if (cpu_has_veic) {
set_vi_handler (MSC01E_INT_CPUCTR, mips_timer_dispatch);
else
#endif
{
- if (cpu_has_mips_r2)
- /*
- * Read IntCtl.IPTI to determine the timer interrupt
- */
- hwint = (read_c0_intctl () >> 29) & 7;
- else
- hwint = MIPSCPU_INT_CPUCTR;
if (cpu_has_vint)
- set_vi_handler (hwint, mips_timer_dispatch);
- mips_cpu_timer_irq = MIPSCPU_INT_BASE + hwint;
+ set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
+ mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
}
/* we are using the cpu counter for timer interrupts */
irq->handler = mips_timer_interrupt; /* we use our own handler */
#ifdef CONFIG_MIPS_MT_SMTC
- setup_irq_smtc(mips_cpu_timer_irq, irq, 0x100 << hwint);
+ setup_irq_smtc(mips_cpu_timer_irq, irq, 0x100 << cp0_compare_irq);
#else
setup_irq(mips_cpu_timer_irq, irq);
#endif /* CONFIG_MIPS_MT_SMTC */
if (irq == MIPSCPU_INT_I8259A)
malta_hw0_irqdispatch();
else if (irq > 0)
- do_IRQ(MIPSCPU_INT_BASE + irq);
+ do_IRQ(MIPS_CPU_IRQ_BASE + irq);
else
spurious_interrupt();
}
set_vi_handler (MIPSCPU_INT_I8259A, malta_hw0_irqdispatch);
set_vi_handler (MIPSCPU_INT_COREHI, corehi_irqdispatch);
#ifdef CONFIG_MIPS_MT_SMTC
- setup_irq_smtc (MIPSCPU_INT_BASE+MIPSCPU_INT_I8259A, &i8259irq,
+ setup_irq_smtc (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_I8259A, &i8259irq,
(0x100 << MIPSCPU_INT_I8259A));
- setup_irq_smtc (MIPSCPU_INT_BASE+MIPSCPU_INT_COREHI,
+ setup_irq_smtc (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_COREHI,
&corehi_irqaction, (0x100 << MIPSCPU_INT_COREHI));
#else /* Not SMTC */
- setup_irq (MIPSCPU_INT_BASE+MIPSCPU_INT_I8259A, &i8259irq);
- setup_irq (MIPSCPU_INT_BASE+MIPSCPU_INT_COREHI, &corehi_irqaction);
+ setup_irq (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_I8259A, &i8259irq);
+ setup_irq (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_COREHI, &corehi_irqaction);
#endif /* CONFIG_MIPS_MT_SMTC */
}
else {
- setup_irq (MIPSCPU_INT_BASE+MIPSCPU_INT_I8259A, &i8259irq);
- setup_irq (MIPSCPU_INT_BASE+MIPSCPU_INT_COREHI, &corehi_irqaction);
+ setup_irq (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_I8259A, &i8259irq);
+ setup_irq (MIPS_CPU_IRQ_BASE+MIPSCPU_INT_COREHI, &corehi_irqaction);
}
}
irq = irq_ffs(pending);
if (irq >= 0)
- do_IRQ(MIPSCPU_INT_BASE + irq);
+ do_IRQ(MIPS_CPU_IRQ_BASE + irq);
else
spurious_interrupt();
}
#else
s.iobase = SEAD_UART0_REGS_BASE+3;
#endif
- s.irq = MIPSCPU_INT_BASE + MIPSCPU_INT_UART0;
+ s.irq = MIPS_CPU_IRQ_BASE + MIPSCPU_INT_UART0;
s.uartclk = SEAD_BASE_BAUD * 16;
s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ;
s.iotype = UPIO_PORT;
irq = irq_ffs(pending);
if (irq > 0)
- do_IRQ(MIPSCPU_INT_BASE + irq);
+ do_IRQ(MIPS_CPU_IRQ_BASE + irq);
else
spurious_interrupt();
}
int vpflags = dvpe();
write_c0_compare (read_c0_count() - 1);
- clear_c0_cause(0x100 << MIPSCPU_INT_CPUCTR);
- set_c0_status(0x100 << MIPSCPU_INT_CPUCTR);
+ clear_c0_cause(0x100 << cp0_compare_irq);
+ set_c0_status(0x100 << cp0_compare_irq);
irq_enable_hazard();
evpe(vpflags);
}
else {
if (cpu_has_vint)
- set_vi_handler(MIPSCPU_INT_CPUCTR, mips_timer_dispatch);
- mips_cpu_timer_irq = MIPSCPU_INT_BASE + MIPSCPU_INT_CPUCTR;
+ set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
+ mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
}
/* we are using the cpu counter for timer interrupts */
#include <asm/uaccess.h>
#include <asm/assembly.h>
+#include <asm/asm-offsets.h>
+#include <asm/ptrace.h>
#include <asm/unwind.h>
#define dbg(x...)
#endif
+#define KERNEL_START (KERNEL_BINARY_TEXT_START - 0x1000)
+
extern struct unwind_table_entry __start___unwind[];
extern struct unwind_table_entry __stop___unwind[];
return 0;
}
+#ifdef CONFIG_64BIT
+#define get_func_addr(fptr) fptr[2]
+#else
+#define get_func_addr(fptr) fptr[0]
+#endif
+
+static int unwind_special(struct unwind_frame_info *info, unsigned long pc, int frame_size)
+{
+ void handle_interruption(int, struct pt_regs *);
+ static unsigned long *hi = (unsigned long)&handle_interruption;
+
+ if (pc == get_func_addr(hi)) {
+ struct pt_regs *regs = (struct pt_regs *)(info->sp - frame_size - PT_SZ_ALGN);
+ dbg("Unwinding through handle_interruption()\n");
+ info->prev_sp = regs->gr[30];
+ info->prev_ip = regs->iaoq[0];
+
+ return 1;
+ }
+
+ return 0;
+}
+
static void unwind_frame_regs(struct unwind_frame_info *info)
{
const struct unwind_table_entry *e;
}
}
- info->prev_sp = info->sp - frame_size;
- if (e->Millicode)
- info->rp = info->r31;
- else if (rpoffset)
- info->rp = *(unsigned long *)(info->prev_sp - rpoffset);
- info->prev_ip = info->rp;
- info->rp = 0;
+ if (!unwind_special(info, e->region_start, frame_size)) {
+ info->prev_sp = info->sp - frame_size;
+ if (e->Millicode)
+ info->rp = info->r31;
+ else if (rpoffset)
+ info->rp = *(unsigned long *)(info->prev_sp - rpoffset);
+ info->prev_ip = info->rp;
+ info->rp = 0;
+ }
dbg("analyzing func @ %lx, setting prev_sp=%lx "
"prev_ip=%lx npc=%lx\n", info->ip, info->prev_sp,
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21-rc6
-# Mon Apr 23 20:46:48 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 12:32:34 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_PPC_OF_PLATFORM_PCI=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=4
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
CONFIG_CPUSETS=y
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
CONFIG_SPU_BASE=y
CONFIG_CBE_RAS=y
CONFIG_CBE_THERM=m
+CONFIG_CBE_CPUFREQ=m
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
CONFIG_UDBG_RTAS_CONSOLE=y
CONFIG_PPC_UDBG_BEAT=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
# CONFIG_U3_DART is not set
CONFIG_PPC_RTAS=y
# CONFIG_RTAS_ERROR_LOGGING is not set
# CONFIG_PPC_970_NAP is not set
CONFIG_PPC_INDIRECT_IO=y
CONFIG_GENERIC_IOMAP=y
-# CONFIG_CPU_FREQ_PMAC64 is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+
+#
+# CPU Frequency drivers
+#
+# CONFIG_CPM2 is not set
#
# Kernel options
CONFIG_ZONE_DMA_FLAG=1
CONFIG_ARCH_MEMORY_PROBE=y
CONFIG_NODES_SPAN_OTHER_NODES=y
+CONFIG_PPC_HAS_HASH_64K=y
CONFIG_PPC_64K_PAGES=y
CONFIG_SCHED_SMT=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
#
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_IPV6_OPTIMISTIC_DAD is not set
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NF_CONNTRACK is not set
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
CONFIG_NETFILTER_XT_TARGET_DSCP=m
#
# CONFIG_IP6_NF_QUEUE is not set
# CONFIG_IP6_NF_IPTABLES is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
# CONFIG_DM_MULTIPATH_EMC is not set
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=m
CONFIG_SKGE=m
CONFIG_SKY2=m
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
CONFIG_SPIDER_NET=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_PASEMI_MAC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
#
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PASEMI is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
#
# Multifunction device drivers
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
CONFIG_HID=m
# CONFIG_HID_DEBUG is not set
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+
#
# USB support
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-# CONFIG_USB_HID is not set
-
-#
-# USB HID Boot Protocol drivers
-#
-# CONFIG_USB_KBD is not set
-# CONFIG_USB_MOUSE is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-# CONFIG_USB_GTCO is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
+CONFIG_INFINIBAND_USER_MEM=y
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
# CONFIG_INFINIBAND_AMSO1100 is not set
+# CONFIG_MLX4_INFINIBAND is not set
CONFIG_INFINIBAND_IPOIB=m
# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=15
# CONFIG_DETECT_SOFTLOCKUP is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Tue May 8 12:32:16 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 12:33:17 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_PPC_OF_PLATFORM_PCI=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=4
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# Cell Broadband Engine options
#
CONFIG_SPU_FS=y
+CONFIG_SPU_FS_64K_LS=y
CONFIG_SPU_BASE=y
# CONFIG_PQ2ADS is not set
CONFIG_PPC_UDBG_BEAT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_ARCH_MEMORY_PROBE=y
CONFIG_NODES_SPAN_OTHER_NODES=y
+CONFIG_PPC_HAS_HASH_64K=y
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_SCHED_SMT is not set
CONFIG_PROC_DEVICETREE=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
#
# CONFIG_IP6_NF_QUEUE is not set
# CONFIG_IP6_NF_IPTABLES is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
# CONFIG_DM_MULTIPATH_EMC is not set
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
CONFIG_SPIDER_NET=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_PASEMI_MAC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
#
# Multifunction device drivers
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-# CONFIG_USB_GTCO is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=15
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set
CONFIG_PPC_EARLY_DEBUG_BEAT=y
+# CONFIG_PPC_EARLY_DEBUG_44x is not set
#
# Security options
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:12:58 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 12:36:45 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
-# CONFIG_8xx is not set
# CONFIG_E200 is not set
CONFIG_6xx=y
CONFIG_PPC_FPU=y
# CONFIG_ALTIVEC is not set
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
CONFIG_SMP=y
CONFIG_NR_CPUS=4
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_APUS is not set
CONFIG_PPC_CHRP=y
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
# CONFIG_PPC_EFIKA is not set
# CONFIG_PPC_LITE5200 is not set
# CONFIG_PPC_PMAC is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
# CONFIG_UDBG_RTAS_CONSOLE is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+CONFIG_PPC_I8259=y
CONFIG_PPC_RTAS=y
# CONFIG_RTAS_ERROR_LOGGING is not set
CONFIG_RTAS_PROC=y
# CONFIG_GENERIC_IOMAP is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_TAU is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
CONFIG_ISA=y
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-CONFIG_PPC_I8259=y
CONFIG_PPC_INDIRECT_PCI=y
+# CONFIG_PPC_INDIRECT_PCI_BE is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
# CONFIG_NF_CT_ACCT is not set
# CONFIG_NF_CONNTRACK_MARK is not set
CONFIG_NF_CONNTRACK_IRC=m
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
+# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
-# CONFIG_NETFILTER_XTABLES is not set
+CONFIG_NETFILTER_XTABLES=m
+# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
+# CONFIG_NETFILTER_XT_TARGET_MARK is not set
+# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
+# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
+# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
+# CONFIG_NETFILTER_XT_MATCH_ESP is not set
+# CONFIG_NETFILTER_XT_MATCH_HELPER is not set
+# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
+# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set
+# CONFIG_NETFILTER_XT_MATCH_MAC is not set
+# CONFIG_NETFILTER_XT_MATCH_MARK is not set
+# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set
+# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set
+# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
+# CONFIG_NETFILTER_XT_MATCH_REALM is not set
+# CONFIG_NETFILTER_XT_MATCH_SCTP is not set
+# CONFIG_NETFILTER_XT_MATCH_STATE is not set
+# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
+# CONFIG_NETFILTER_XT_MATCH_STRING is not set
+# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
+# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
#
# IP: Netfilter Configuration
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
# CONFIG_IP_NF_QUEUE is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
+CONFIG_IP_NF_IPTABLES=m
+# CONFIG_IP_NF_MATCH_IPRANGE is not set
+# CONFIG_IP_NF_MATCH_TOS is not set
+# CONFIG_IP_NF_MATCH_RECENT is not set
+# CONFIG_IP_NF_MATCH_ECN is not set
+# CONFIG_IP_NF_MATCH_AH is not set
+# CONFIG_IP_NF_MATCH_TTL is not set
+# CONFIG_IP_NF_MATCH_OWNER is not set
+# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+# CONFIG_IP_NF_TARGET_ULOG is not set
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+# CONFIG_IP_NF_TARGET_NETMAP is not set
+# CONFIG_IP_NF_TARGET_SAME is not set
+# CONFIG_NF_NAT_SNMP_BASIC is not set
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+CONFIG_NF_NAT_TFTP=m
+# CONFIG_NF_NAT_AMANDA is not set
+# CONFIG_NF_NAT_PPTP is not set
+# CONFIG_NF_NAT_H323 is not set
+CONFIG_NF_NAT_SIP=m
+# CONFIG_IP_NF_MANGLE is not set
+# CONFIG_IP_NF_RAW is not set
+# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
# Plug and Play support
#
# CONFIG_PNP is not set
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
CONFIG_VIA_RHINE=y
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_VIA_RHINE_NAPI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+# CONFIG_SC92031 is not set
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
CONFIG_MV643XX_ETH=y
-# CONFIG_MV643XX_ETH_0 is not set
-# CONFIG_MV643XX_ETH_1 is not set
-# CONFIG_MV643XX_ETH_2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
# CONFIG_INPUT_PCSPKR is not set
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=y
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=y
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_CLASS_DEVICE=m
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+CONFIG_DISPLAY_SUPPORT=m
+
+#
+# Display hardware drivers
+#
+# CONFIG_VGASTATE is not set
CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
-# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_MATROX_MULTIHEAD is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
+CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
CONFIG_FB_ATY=y
CONFIG_FB_ATY_CT=y
# CONFIG_FB_ATY_GENERIC_LCD is not set
CONFIG_FB_ATY_GX=y
+CONFIG_FB_ATY_BACKLIGHT=y
+# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
CONFIG_FB_3DFX=y
# CONFIG_FB_3DFX_ACCEL is not set
# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-
-#
-# Logo configuration
-#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
-# CONFIG_USB_HIDDEV is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
+# CONFIG_KPROBES is not set
#
# Kernel hacking
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=15
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_RWSEMS is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_DEBUGGER=y
CONFIG_XMON=y
CONFIG_XMON_DEFAULT=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Fri May 4 13:47:08 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 12:38:33 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
CONFIG_BOOKE=y
CONFIG_PTE_64BIT=y
CONFIG_PHYS_64BIT=y
+# CONFIG_PPC_MM_SLICES is not set
CONFIG_NOT_COHERENT_CACHE=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-#
-# PHY device support
-#
-
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
-CONFIG_IBM_NEW_EMAC=y
-CONFIG_IBM_NEW_EMAC_RXB=128
-CONFIG_IBM_NEW_EMAC_TXB=64
-CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
-CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
-CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
-# CONFIG_IBM_NEW_EMAC_DEBUG is not set
-CONFIG_IBM_NEW_EMAC_ZMII=y
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_IBM_EMAC=y
+CONFIG_IBM_EMAC_RXB=128
+CONFIG_IBM_EMAC_TXB=64
+CONFIG_IBM_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_EMAC_DEBUG is not set
+CONFIG_IBM_EMAC_ZMII=y
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
#
# Multifunction device drivers
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUGGER is not set
# CONFIG_BDI_SWITCH is not set
# CONFIG_BOOTX_TEXT is not set
-# CONFIG_SERIAL_TEXT_DEBUG is not set
# CONFIG_PPC_EARLY_DEBUG is not set
#
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=y
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:15:04 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 12:38:34 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC64_SWSUSP=y
#
# Processor support
# CONFIG_PPC_OF_PLATFORM_PCI is not set
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=4
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_PPC_PSERIES is not set
# CONFIG_PPC_ISERIES is not set
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
CONFIG_PPC_PMAC=y
CONFIG_PPC_PMAC64=y
# CONFIG_PPC_MAPLE is not set
# CONFIG_PPC_PASEMI is not set
+# CONFIG_PPC_CELLEB is not set
+# CONFIG_PPC_PS3 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_IBM_CELL_BLADE is not set
-# CONFIG_PPC_PS3 is not set
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
CONFIG_U3_DART=y
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+
+#
+# CPU Frequency drivers
+#
CONFIG_CPU_FREQ_PMAC64=y
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+# CONFIG_PPC_HAS_HASH_64K is not set
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_SCHED_SMT is not set
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
# CONFIG_NF_CT_ACCT is not set
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_IRC=m
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
+# CONFIG_NF_CONNTRACK_SANE is not set
# CONFIG_NF_CONNTRACK_SIP is not set
CONFIG_NF_CONNTRACK_TFTP=m
# CONFIG_NETFILTER_XTABLES is not set
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_SVW=y
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
# CONFIG_DM_MULTIPATH is not set
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
-CONFIG_IEEE1394_OUI_DB=y
-CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
-CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
-# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
-# Device Drivers
+# Controllers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
#
-# Protocol Drivers
+# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
+CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=y
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
+CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB_PMU=y
# CONFIG_ADB_PMU_LED is not set
CONFIG_PMAC_SMU=y
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
CONFIG_ACENIC=y
CONFIG_ACENIC_OMIT_TIGON_I=y
# CONFIG_DL2K is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_PASEMI_MAC is not set
+# CONFIG_MLX4_CORE is not set
CONFIG_TR=y
CONFIG_IBMOL=y
# CONFIG_3C359 is not set
# CONFIG_TMS380TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+# CONFIG_USB_USBNET_MII is not set
+CONFIG_USB_USBNET=m
+# CONFIG_USB_NET_AX8817X is not set
+CONFIG_USB_NET_CDCETHER=m
+# CONFIG_USB_NET_DM9601 is not set
+# CONFIG_USB_NET_GL620A is not set
+# CONFIG_USB_NET_NET1080 is not set
+# CONFIG_USB_NET_PLUSB is not set
+# CONFIG_USB_NET_MCS7830 is not set
+# CONFIG_USB_NET_RNDIS_HOST is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+# CONFIG_USB_NET_ZAURUS is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=y
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_AGP=m
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+# CONFIG_USB_DABUSB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_CLASS_DEVICE=m
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+# CONFIG_DISPLAY_SUPPORT is not set
+CONFIG_VGASTATE=y
CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
-# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
+# CONFIG_FB_NVIDIA_DEBUG is not set
+CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
+CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-
-#
-# Logo configuration
-#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=m
-CONFIG_BACKLIGHT_DEVICE=y
-CONFIG_LCD_CLASS_DEVICE=m
-CONFIG_LCD_DEVICE=y
#
# Sound
#
CONFIG_SND_USB_AUDIO=m
# CONFIG_SND_USB_USX2Y is not set
+# CONFIG_SND_USB_CAIAQ is not set
+
+#
+# System on Chip audio support
+#
+# CONFIG_SND_SOC is not set
#
# Open Sound System
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+CONFIG_HID_FF=y
+CONFIG_HID_PID=y
+CONFIG_LOGITECH_FF=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_THRUSTMASTER_FF=y
+# CONFIG_ZEROPLUS_FF is not set
+CONFIG_USB_HIDDEV=y
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
+CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PCI=y
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-CONFIG_HID_FF=y
-CONFIG_HID_PID=y
-CONFIG_LOGITECH_FF=y
-CONFIG_THRUSTMASTER_FF=y
-# CONFIG_ZEROPLUS_FF is not set
-CONFIG_USB_HIDDEV=y
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-CONFIG_USB_CATC=m
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_RTL8150=m
-# CONFIG_USB_USBNET_MII is not set
-CONFIG_USB_USBNET=m
-# CONFIG_USB_NET_AX8817X is not set
-CONFIG_USB_NET_CDCETHER=m
-# CONFIG_USB_NET_GL620A is not set
-# CONFIG_USB_NET_NET1080 is not set
-# CONFIG_USB_NET_PLUSB is not set
-# CONFIG_USB_NET_MCS7830 is not set
-# CONFIG_USB_NET_RNDIS_HOST is not set
-# CONFIG_USB_NET_CDC_SUBSET is not set
-# CONFIG_USB_NET_ZAURUS is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
-CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUGGER is not set
CONFIG_IRQSTACKS=y
CONFIG_BOOTX_TEXT=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_TEST=m
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Sat May 5 11:02:35 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:22:36 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
# CONFIG_ALTIVEC is not set
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_LINKSTATION is not set
# CONFIG_MPC7448HPC2 is not set
CONFIG_PPC_HOLLY=y
+# CONFIG_PPC_PRPMC2800 is not set
CONFIG_TSI108_BRIDGE=y
CONFIG_MPIC=y
CONFIG_MPIC_WEIRD=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
CONFIG_PHYLIB=y
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
CONFIG_TSI108_ETH=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_LOCKD=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22-rc1
-# Mon May 14 14:27:46 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:22:39 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
CONFIG_IP_SCTP=m
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_BLINK is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_ATA is not set
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_PASEMI_MAC is not set
# CONFIG_MLX4_CORE is not set
-CONFIG_MLX4_DEBUG=y
-
-#
-# Token Ring devices
-#
CONFIG_TR=y
CONFIG_IBMOL=y
# CONFIG_3C359 is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_DLM=m
# CONFIG_DLM_DEBUG is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc6
-# Sun Jan 28 23:13:56 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:25:19 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
-# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_DEFAULT_UIMAGE=y
#
# Processor support
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
-# CONFIG_8xx is not set
# CONFIG_E200 is not set
CONFIG_6xx=y
CONFIG_PPC_FPU=y
# CONFIG_ALTIVEC is not set
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
CONFIG_EMBEDDED6xx=y
# CONFIG_APUS is not set
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_LINKSTATION=y
+# CONFIG_MPC7448HPC2 is not set
+# CONFIG_PPC_HOLLY is not set
+# CONFIG_PPC_PRPMC2800 is not set
+CONFIG_MPC10X_BRIDGE=y
+CONFIG_MPC10X_OPENPIC=y
+# CONFIG_MPC10X_STORE_GATHERING is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
# CONFIG_PPC_MPC106 is not set
# CONFIG_GENERIC_IOMAP is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_TAU is not set
-# CONFIG_KATANA is not set
-# CONFIG_WILLOW is not set
-# CONFIG_CPCI690 is not set
-# CONFIG_POWERPMC250 is not set
-# CONFIG_CHESTNUT is not set
-# CONFIG_SPRUCE is not set
-# CONFIG_HDPU is not set
-# CONFIG_EV64260 is not set
-# CONFIG_LOPEC is not set
-# CONFIG_MVME5100 is not set
-# CONFIG_PPLUS is not set
-# CONFIG_PRPMC750 is not set
-# CONFIG_PRPMC800 is not set
-# CONFIG_SANDPOINT is not set
-CONFIG_LINKSTATION=y
-# CONFIG_MPC7448HPC2 is not set
-# CONFIG_RADSTONE_PPC7D is not set
-# CONFIG_PAL4 is not set
-# CONFIG_GEMINI is not set
-# CONFIG_EST8260 is not set
-# CONFIG_SBC82xx is not set
-# CONFIG_SBS8260 is not set
-# CONFIG_RPX8260 is not set
-# CONFIG_TQM8260 is not set
-# CONFIG_ADS8272 is not set
-# CONFIG_PQ2FADS is not set
-# CONFIG_EV64360 is not set
-CONFIG_PPC_GEN550=y
-CONFIG_MPC10X_BRIDGE=y
-CONFIG_MPC10X_OPENPIC=y
-# CONFIG_MPC10X_STORE_GATHERING is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
CONFIG_PPC_INDIRECT_PCI=y
+# CONFIG_PPC_INDIRECT_PCI_BE is not set
CONFIG_FSL_SOC=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
# CONFIG_NF_CT_ACCT is not set
# CONFIG_NF_CONNTRACK_MARK is not set
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
+# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NETFILTER_XTABLES=m
# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
+# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
# CONFIG_NETFILTER_XT_TARGET_MARK is not set
# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
+# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
# CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
CONFIG_IP_NF_TARGET_REJECT=m
# CONFIG_IP_NF_TARGET_LOG is not set
# CONFIG_IP_NF_TARGET_ULOG is not set
-# CONFIG_IP_NF_TARGET_TCPMSS is not set
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
+# CONFIG_IP_NF_TARGET_CLUSTERIP is not set
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+CONFIG_WIRELESS_EXT=y
+# CONFIG_MAC80211 is not set
CONFIG_IEEE80211=m
CONFIG_IEEE80211_DEBUG=y
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
CONFIG_IEEE80211_SOFTMAC=m
CONFIG_IEEE80211_SOFTMAC_DEBUG=y
-CONFIG_WIRELESS_EXT=y
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-
-#
-# NAND Flash Device Drivers
-#
# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_CAFE is not set
+# CONFIG_MTD_ONENAND is not set
#
-# OneNAND Flash Device Drivers
+# UBI - Unsorted block images
#
-# CONFIG_MTD_ONENAND is not set
+# CONFIG_MTD_UBI is not set
#
# Parallel port support
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=2
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
CONFIG_PATA_IT821X=y
+# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
-#
-CONFIG_NET_RADIO=y
-# CONFIG_NET_WIRELESS_RTNETLINK is not set
-
-#
-# Obsolete Wireless cards support (pre-802.11)
-#
-# CONFIG_STRIP is not set
-
-#
-# Wireless 802.11b ISA/PCI cards support
-#
-# CONFIG_IPW2100 is not set
-# CONFIG_IPW2200 is not set
-# CONFIG_AIRO is not set
-# CONFIG_HERMES is not set
-# CONFIG_ATMEL is not set
-
-#
-# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
+# Wireless LAN
#
-# CONFIG_PRISM54 is not set
-# CONFIG_USB_ZD1201 is not set
-# CONFIG_HOSTAP is not set
-# CONFIG_BCM43XX is not set
-CONFIG_ZD1211RW=m
-# CONFIG_ZD1211RW_DEBUG is not set
-CONFIG_NET_WIRELESS=y
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
CONFIG_NETPOLL=y
-# CONFIG_NETPOLL_RX is not set
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
CONFIG_INPUT_UINPUT=m
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
# HID Devices
#
CONFIG_HID=m
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
+CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PCI=y
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-# CONFIG_USB_HID is not set
-
-#
-# USB HID Boot Protocol drivers
-#
-# CONFIG_USB_KBD is not set
-# CONFIG_USB_MOUSE is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
#
-# RTC drivers
+# I2C RTC drivers
#
-# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_DS1307 is not set
-# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
-# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+CONFIG_RTC_DRV_RS5C372=y
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
-CONFIG_RTC_DRV_RS5C372=y
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_TEST is not set
# CONFIG_RTC_DRV_V3020 is not set
+#
+# on-CPU RTC drivers
+#
+
#
# DMA Engine support
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
-CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
+# CONFIG_KPROBES is not set
#
# Kernel hacking
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUGGER is not set
# CONFIG_BDI_SWITCH is not set
# CONFIG_BOOTX_TEXT is not set
-# CONFIG_SERIAL_TEXT_DEBUG is not set
# CONFIG_PPC_EARLY_DEBUG is not set
#
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:18:18 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:26:09 2007
#
# CONFIG_PPC64 is not set
+CONFIG_PPC_PM_NEEDS_RTC_LIB=y
CONFIG_PPC32=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
-# CONFIG_8xx is not set
# CONFIG_E200 is not set
CONFIG_6xx=y
CONFIG_PPC_FPU=y
# CONFIG_ALTIVEC is not set
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
# CONFIG_EPOLL is not set
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_APUS is not set
# CONFIG_PPC_CHRP is not set
CONFIG_PPC_MPC52xx=y
+CONFIG_PPC_MPC5200=y
+CONFIG_PPC_MPC5200_BUGFIX=y
# CONFIG_PPC_EFIKA is not set
CONFIG_PPC_LITE5200=y
# CONFIG_PPC_PMAC is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
# CONFIG_PPC_MPC106 is not set
# CONFIG_GENERIC_IOMAP is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_TAU is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-# CONFIG_MPIC is not set
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_PM=y
# CONFIG_PM_SYSFS_DEPRECATED is not set
# CONFIG_SOFTWARE_SUSPEND is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_INDIRECT_PCI is not set
+CONFIG_FSL_SOC=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
+CONFIG_PATA_MPC52xx=y
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-#
-# PHY device support
-#
-
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
+# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_MV643XX_ETH is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
#
# Real Time Clock
#
+CONFIG_RTC_LIB=y
# CONFIG_RTC_CLASS is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUGGER is not set
# CONFIG_BDI_SWITCH is not set
# CONFIG_BOOTX_TEXT is not set
-# CONFIG_SERIAL_TEXT_DEBUG is not set
# CONFIG_PPC_EARLY_DEBUG is not set
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:19:02 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:27:35 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
# CONFIG_PPC_OF_PLATFORM_PCI is not set
# CONFIG_ALTIVEC is not set
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=4
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
# CONFIG_CPUSETS is not set
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
-CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_PPC_PSERIES is not set
# CONFIG_PPC_ISERIES is not set
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
# CONFIG_PPC_PMAC is not set
CONFIG_PPC_MAPLE=y
# CONFIG_PPC_PASEMI is not set
+# CONFIG_PPC_CELLEB is not set
+# CONFIG_PPC_PS3 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_IBM_CELL_BLADE is not set
-# CONFIG_PPC_PS3 is not set
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
CONFIG_UDBG_RTAS_CONSOLE=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
CONFIG_U3_DART=y
CONFIG_PPC_RTAS=y
# CONFIG_RTAS_ERROR_LOGGING is not set
CONFIG_RTAS_PROC=y
# CONFIG_RTAS_FLASH is not set
-# CONFIG_MMIO_NVRAM is not set
+CONFIG_MMIO_NVRAM=y
CONFIG_MPIC_U3_HT_IRQS=y
# CONFIG_PPC_MPC106 is not set
CONFIG_PPC_970_NAP=y
# CONFIG_PPC_INDIRECT_IO is not set
# CONFIG_GENERIC_IOMAP is not set
# CONFIG_CPU_FREQ is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+# CONFIG_PPC_HAS_HASH_64K is not set
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_SCHED_SMT is not set
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
CONFIG_KERNEL_START=0xc000000000000000
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_IDE_TASK_IOCTL=y
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+# CONFIG_SC92031 is not set
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_PASEMI_MAC is not set
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+CONFIG_USB_PEGASUS=y
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
# CONFIG_FB is not set
# CONFIG_FB_IBM_GXT4500 is not set
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
#
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
-# CONFIG_USB_HIDDEV is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-CONFIG_USB_PEGASUS=y
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
CONFIG_DEBUG_SLAB=y
# CONFIG_DEBUG_SLAB_LEAK is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
+# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_DEBUGGER=y
CONFIG_XMON=y
CONFIG_XMON_DEFAULT=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Mon May 14 12:55:04 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 13:51:39 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_BLINK is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
# CONFIG_SCSI_SRP is not set
#
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
CONFIG_PHYLIB=y
#
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_NETXEN_NIC is not set
CONFIG_PASEMI_MAC=y
# CONFIG_MLX4_CORE is not set
-CONFIG_MLX4_DEBUG=y
-
-#
-# Token Ring devices
-#
# CONFIG_TR is not set
#
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
-
-#
-# PCMCIA network device support
-#
# CONFIG_NET_PCMCIA is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:28:56 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 14:11:36 2007
#
# CONFIG_PPC64 is not set
+CONFIG_PPC_PM_NEEDS_RTC_LIB=y
CONFIG_PPC32=y
CONFIG_PPC_MERGE=y
CONFIG_MMU=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
# CONFIG_DEFAULT_UIMAGE is not set
#
# CONFIG_PPC_83xx is not set
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
# CONFIG_40x is not set
# CONFIG_44x is not set
-# CONFIG_8xx is not set
# CONFIG_E200 is not set
CONFIG_6xx=y
CONFIG_PPC_FPU=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
# CONFIG_SMP is not set
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_APUS is not set
# CONFIG_PPC_CHRP is not set
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
# CONFIG_PPC_EFIKA is not set
# CONFIG_PPC_LITE5200 is not set
CONFIG_PPC_PMAC=y
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
CONFIG_PPC_MPC106=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+
+#
+# CPU Frequency drivers
+#
CONFIG_CPU_FREQ_PMAC=y
CONFIG_PPC601_SYNC_FIX=y
# CONFIG_TAU is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
CONFIG_PM=y
CONFIG_PM_SYSFS_DEPRECATED=y
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_PM_STD_PARTITION=""
+CONFIG_APM_EMULATION=y
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-# CONFIG_PPC_I8259 is not set
CONFIG_PPC_INDIRECT_PCI=y
+# CONFIG_PPC_INDIRECT_PCI_BE is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
# CONFIG_PCI_DEBUG is not set
#
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
CONFIG_PCCARD_NONSTATIC=m
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
#
# CONFIG_NETFILTER_NETLINK is not set
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
# CONFIG_NF_CT_ACCT is not set
# CONFIG_NF_CONNTRACK_MARK is not set
CONFIG_NF_CONNTRACK_IRC=m
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
+# CONFIG_NF_CONNTRACK_SANE is not set
# CONFIG_NF_CONNTRACK_SIP is not set
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
CONFIG_NETFILTER_XT_TARGET_MARK=m
CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+# CONFIG_NETFILTER_XT_MATCH_CONNBYTES is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNMARK is not set
CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
+# CONFIG_IP_NF_TARGET_CLUSTERIP is not set
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
CONFIG_IP_DCCP=m
CONFIG_INET_DCCP_DIAG=m
CONFIG_IP_DCCP_ACKVEC=y
# DCCP Kernel Hacking
#
# CONFIG_IP_DCCP_DEBUG is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
+CONFIG_NET_SCH_FIFO=y
CONFIG_NET_CLS_ROUTE=y
#
# Dongle support
#
# CONFIG_DONGLE is not set
+# CONFIG_KINGSUN_DONGLE is not set
#
# Old SIR device drivers
# CONFIG_BT_HCIBLUECARD is not set
# CONFIG_BT_HCIBTUART is not set
# CONFIG_BT_HCIVHCI is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+CONFIG_CFG80211=m
+CONFIG_WIRELESS_EXT=y
+CONFIG_MAC80211=m
+CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUG is not set
CONFIG_IEEE80211=m
# CONFIG_IEEE80211_DEBUG is not set
CONFIG_IEEE80211_CRYPT_WEP=m
CONFIG_IEEE80211_CRYPT_CCMP=m
CONFIG_IEEE80211_CRYPT_TKIP=m
# CONFIG_IEEE80211_SOFTMAC is not set
-CONFIG_WIRELESS_EXT=y
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
#
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECS=m
+# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
# CONFIG_IDE_GENERIC is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
# CONFIG_DM_MULTIPATH is not set
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
-# CONFIG_IEEE1394_OUI_DB is not set
-CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
-CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
-# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
-# Device Drivers
+# Controllers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
-# Protocol Drivers
+# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
+# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
# CONFIG_IEEE1394_ETH1394 is not set
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
+CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB=y
CONFIG_ADB_CUDA=y
CONFIG_ADB_PMU=y
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+# CONFIG_SC92031 is not set
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_BNX2 is not set
# CONFIG_MV643XX_ETH is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
-#
-CONFIG_NET_RADIO=y
-# CONFIG_NET_WIRELESS_RTNETLINK is not set
-
-#
-# Obsolete Wireless cards support (pre-802.11)
-#
-# CONFIG_STRIP is not set
-# CONFIG_PCMCIA_WAVELAN is not set
-# CONFIG_PCMCIA_NETWAVE is not set
-
-#
-# Wireless 802.11 Frequency Hopping cards support
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+CONFIG_WLAN_80211=y
# CONFIG_PCMCIA_RAYCS is not set
-
-#
-# Wireless 802.11b ISA/PCI cards support
-#
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
+# CONFIG_LIBERTAS is not set
# CONFIG_AIRO is not set
CONFIG_HERMES=m
CONFIG_APPLE_AIRPORT=m
# CONFIG_PLX_HERMES is not set
# CONFIG_TMD_HERMES is not set
# CONFIG_NORTEL_HERMES is not set
-# CONFIG_PCI_HERMES is not set
+CONFIG_PCI_HERMES=m
# CONFIG_ATMEL is not set
-
-#
-# Wireless 802.11b Pcmcia/Cardbus cards support
-#
-# CONFIG_PCMCIA_HERMES is not set
+CONFIG_PCMCIA_HERMES=m
# CONFIG_PCMCIA_SPECTRUM is not set
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set
-
-#
-# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
-#
CONFIG_PRISM54=m
# CONFIG_USB_ZD1201 is not set
# CONFIG_HOSTAP is not set
-CONFIG_NET_WIRELESS=y
#
-# PCMCIA network device support
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+CONFIG_USB_USBNET_MII=m
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_AX8817X=m
+CONFIG_USB_NET_CDCETHER=m
+# CONFIG_USB_NET_DM9601 is not set
+# CONFIG_USB_NET_GL620A is not set
+CONFIG_USB_NET_NET1080=m
+# CONFIG_USB_NET_PLUSB is not set
+# CONFIG_USB_NET_MCS7830 is not set
+# CONFIG_USB_NET_RNDIS_HOST is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+CONFIG_USB_NET_ZAURUS=m
# CONFIG_NET_PCMCIA is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_PMACZILOG=m
# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=y
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
CONFIG_AGP=m
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_CLASS_DEVICE=m
#
-# Graphics support
+# Display device support
#
-# CONFIG_FIRMWARE_EDID is not set
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+CONFIG_VGASTATE=y
CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
+# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
CONFIG_FB_MATROX=y
# CONFIG_FB_ATY_GENERIC_LCD is not set
CONFIG_FB_ATY_GX=y
CONFIG_FB_ATY_BACKLIGHT=y
+# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
CONFIG_FB_3DFX=y
# CONFIG_FB_3DFX_ACCEL is not set
# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
# CONFIG_FB_IBM_GXT4500 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-
-#
-# Logo configuration
-#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_DEVICE=y
-CONFIG_LCD_CLASS_DEVICE=m
-CONFIG_LCD_DEVICE=y
#
# Sound
#
CONFIG_SOUND=m
-CONFIG_DMASOUND_PMAC=m
-CONFIG_DMASOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND_USB_AUDIO=m
# CONFIG_SND_USB_USX2Y is not set
+# CONFIG_SND_USB_CAIAQ is not set
#
# PCMCIA devices
# CONFIG_SND_VXPOCKET is not set
# CONFIG_SND_PDAUDIOCF is not set
+#
+# System on Chip audio support
+#
+# CONFIG_SND_SOC is not set
+
#
# Open Sound System
#
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+CONFIG_USB_HIDINPUT_POWERBOOK=y
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
CONFIG_USB_DYNAMIC_MINORS=y
# CONFIG_USB_SUSPEND is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-CONFIG_USB_HIDINPUT_POWERBOOK=y
-# CONFIG_HID_FF is not set
-# CONFIG_USB_HIDDEV is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-CONFIG_USB_APPLETOUCH=y
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-CONFIG_USB_USBNET_MII=m
-CONFIG_USB_USBNET=m
-CONFIG_USB_NET_AX8817X=m
-CONFIG_USB_NET_CDCETHER=m
-# CONFIG_USB_NET_GL620A is not set
-CONFIG_USB_NET_NET1080=m
-# CONFIG_USB_NET_PLUSB is not set
-# CONFIG_USB_NET_MCS7830 is not set
-# CONFIG_USB_NET_RNDIS_HOST is not set
-# CONFIG_USB_NET_CDC_SUBSET is not set
-CONFIG_USB_NET_ZAURUS=m
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
#
# Real Time Clock
#
+CONFIG_RTC_LIB=y
# CONFIG_RTC_CLASS is not set
#
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
-CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_TEXTSEARCH_BM=m
CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
+# CONFIG_KPROBES is not set
#
# Kernel hacking
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUGGER=y
CONFIG_XMON=y
CONFIG_XMON_DEFAULT=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:28:58 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 14:15:02 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_AUDIT_ARCH=y
CONFIG_GENERIC_BUG=y
# CONFIG_DEFAULT_UIMAGE is not set
+CONFIG_PPC64_SWSUSP=y
#
# Processor support
CONFIG_PPC_OF_PLATFORM_PCI=y
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=32
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_TASKSTATS=y
CONFIG_TASK_DELAY_ACCT=y
+# CONFIG_TASK_XACCT is not set
# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
CONFIG_CPUSETS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-# CONFIG_TASK_XACCT is not set
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_EMBEDDED6xx is not set
# CONFIG_APUS is not set
CONFIG_PPC_PSERIES=y
+CONFIG_PPC_SPLPAR=y
+CONFIG_EEH=y
+CONFIG_SCANLOG=m
+CONFIG_LPARCFG=y
CONFIG_PPC_ISERIES=y
+
+#
+# iSeries device drivers
+#
+CONFIG_VIODASD=y
+CONFIG_VIOCD=m
+CONFIG_VIOTAPE=m
+CONFIG_VIOPATH=y
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
CONFIG_PPC_PMAC=y
CONFIG_PPC_PMAC64=y
CONFIG_PPC_MAPLE=y
# CONFIG_PPC_PASEMI is not set
+CONFIG_PPC_CELLEB=y
+# CONFIG_PPC_PS3 is not set
CONFIG_PPC_CELL=y
CONFIG_PPC_CELL_NATIVE=y
CONFIG_PPC_IBM_CELL_BLADE=y
-# CONFIG_PPC_PS3 is not set
+
+#
+# Cell Broadband Engine options
+#
+CONFIG_SPU_FS=m
+CONFIG_SPU_FS_64K_LS=y
+CONFIG_SPU_BASE=y
+CONFIG_CBE_RAS=y
+CONFIG_CBE_THERM=m
+CONFIG_CBE_CPUFREQ=m
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
CONFIG_UDBG_RTAS_CONSOLE=y
+CONFIG_PPC_UDBG_BEAT=y
CONFIG_XICS=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+CONFIG_PPC_I8259=y
CONFIG_U3_DART=y
CONFIG_PPC_RTAS=y
CONFIG_RTAS_ERROR_LOGGING=y
CONFIG_RTAS_PROC=y
CONFIG_RTAS_FLASH=m
+CONFIG_PPC_PMI=m
CONFIG_MMIO_NVRAM=y
CONFIG_MPIC_U3_HT_IRQS=y
CONFIG_IBMVIO=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
-CONFIG_CPU_FREQ_PMAC64=y
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
#
-# Cell Broadband Engine options
+# CPU Frequency drivers
#
-CONFIG_SPU_FS=m
-CONFIG_SPU_BASE=y
-CONFIG_CBE_RAS=y
-CONFIG_CBE_THERM=m
-CONFIG_CBE_CPUFREQ=m
+CONFIG_CPU_FREQ_PMAC64=y
+# CONFIG_CPM2 is not set
#
# Kernel options
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
-CONFIG_PPC_SPLPAR=y
-CONFIG_EEH=y
-CONFIG_SCANLOG=m
-CONFIG_LPARCFG=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_MEMORY_HOTPLUG_SPARSE=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_ARCH_MEMORY_PROBE=y
+CONFIG_PPC_HAS_HASH_64K=y
# CONFIG_PPC_64K_PAGES is not set
# CONFIG_SCHED_SMT is not set
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-CONFIG_PPC_I8259=y
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
CONFIG_HOTPLUG_PCI=m
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_IRC=m
CONFIG_NF_CONNTRACK_NETBIOS_NS=m
CONFIG_NF_CONNTRACK_PPTP=m
+# CONFIG_NF_CONNTRACK_SANE is not set
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
-# CONFIG_NETFILTER_XTABLES is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
#
# IP: Netfilter Configuration
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_IPRANGE=m
+CONFIG_IP_NF_MATCH_TOS=m
+CONFIG_IP_NF_MATCH_RECENT=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_MATCH_OWNER=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_SAME=m
+CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_PROTO_GRE=m
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+CONFIG_NF_NAT_TFTP=m
+CONFIG_NF_NAT_AMANDA=m
+CONFIG_NF_NAT_PPTP=m
+CONFIG_NF_NAT_H323=m
+CONFIG_NF_NAT_SIP=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_TOS=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
+CONFIG_NET_CLS_ROUTE=y
#
# Network testing
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
+CONFIG_BLK_DEV_CELLEB=y
CONFIG_BLK_DEV_IDE_PMAC=y
CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
CONFIG_BLK_DEV_IDEDMA_PMAC=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
CONFIG_SCSI_DEBUG=m
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
+CONFIG_ATA_NONSTANDARD=y
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_SVW=y
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
CONFIG_PATA_WINBOND=y
+CONFIG_PATA_SCC=y
#
# Multi-device support (RAID and LVM)
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
-# CONFIG_IEEE1394_OUI_DB is not set
-CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
-CONFIG_IEEE1394_CONFIG_ROM_IP1394=y
-# CONFIG_IEEE1394_EXPORT_FULL_API is not set
#
-# Device Drivers
+# Controllers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=y
#
-# Protocol Drivers
+# Protocols
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
+CONFIG_IEEE1394_ETH1394_ROM_ENTRY=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=y
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
+CONFIG_MACINTOSH_DRIVERS=y
CONFIG_ADB_PMU=y
# CONFIG_ADB_PMU_LED is not set
CONFIG_PMAC_SMU=y
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=m
#
-# PHY device support
+# MII PHY device drivers
#
-# CONFIG_PHYLIB is not set
+CONFIG_MARVELL_PHY=m
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=m
+CONFIG_FIXED_PHY=m
+CONFIG_FIXED_MII_10_FDX=y
+CONFIG_FIXED_MII_100_FDX=y
#
# Ethernet (10 or 100Mbit)
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+# CONFIG_SC92031 is not set
+CONFIG_NETDEV_1000=y
CONFIG_ACENIC=y
CONFIG_ACENIC_OMIT_TIGON_I=y
# CONFIG_DL2K is not set
# CONFIG_BNX2 is not set
CONFIG_SPIDER_NET=m
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+CONFIG_PASEMI_MAC=m
+# CONFIG_MLX4_CORE is not set
CONFIG_TR=y
CONFIG_IBMOL=y
# CONFIG_3C359 is not set
# CONFIG_TMS380TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
CONFIG_ISERIES_VETH=m
# CONFIG_FDDI is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
CONFIG_NETPOLL=y
-CONFIG_NETPOLL_RX=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
#
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_PMACZILOG is not set
CONFIG_SERIAL_ICOM=m
+CONFIG_SERIAL_TXX9=y
+CONFIG_HAS_TXX9_SERIAL=y
+CONFIG_SERIAL_TXX9_NR_UARTS=6
+CONFIG_SERIAL_TXX9_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_HVC_CONSOLE=y
CONFIG_HVC_ISERIES=y
CONFIG_HVC_RTAS=y
+CONFIG_HVC_BEAT=y
CONFIG_HVCS=m
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_CLASS_DEVICE=y
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+# CONFIG_VGASTATE is not set
CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
-# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
+CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
CONFIG_FB_IBM_GXT4500=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-
-#
-# Logo configuration
-#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_DEVICE=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_LCD_DEVICE=y
#
# Sound
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
+# CONFIG_SND_USB_CAIAQ is not set
+
+#
+# System on Chip audio support
+#
+# CONFIG_SND_SOC is not set
#
# Open Sound System
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+CONFIG_USB_HIDDEV=y
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_EHCI_TT_NEWSCHED=y
+CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
-CONFIG_USB_HIDDEV=y
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
+# CONFIG_INFINIBAND_IPATH is not set
# CONFIG_INFINIBAND_AMSO1100 is not set
+# CONFIG_MLX4_INFINIBAND is not set
CONFIG_INFINIBAND_IPOIB=m
+# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
# CONFIG_INFINIBAND_SRP is not set
# DMA Devices
#
-#
-# Virtualization
-#
-
#
# File systems
#
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
#
# Native Language Support
# Distributed Lock Manager
#
# CONFIG_DLM is not set
-
-#
-# iSeries device drivers
-#
-# CONFIG_VIOCONS is not set
-CONFIG_VIODASD=y
-CONFIG_VIOCD=m
-CONFIG_VIOTAPE=m
-CONFIG_VIOPATH=y
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
+CONFIG_TEXTSEARCH_BM=m
+CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
+# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_HCALL_STATS is not set
CONFIG_DEBUGGER=y
CONFIG_XMON=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_TEST=m
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Wed May 9 09:42:46 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 14:15:11 2007
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
-# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_BLINK is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
CONFIG_PHYLIB=y
#
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
CONFIG_MV643XX_ETH=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_MLX4_CORE is not set
# CONFIG_TR is not set
#
# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
# Graphics support
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# DMA Devices
#
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
#
# File systems
#
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21
-# Fri May 11 10:16:27 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 14:15:19 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Misc devices
#
# CONFIG_BLINK is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
# CONFIG_IDE is not set
#
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_ESP_CORE is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
#
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-#
-# PHY device support
-#
-
#
# Ethernet (10 or 100Mbit)
#
# CONFIG_NET_ETHERNET is not set
CONFIG_MII=m
-
-#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-CONFIG_MLX4_DEBUG=y
-
-#
-# Token Ring devices
-#
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
# Wireless LAN
# CONFIG_USB_NET_RNDIS_HOST is not set
# CONFIG_USB_NET_CDC_SUBSET is not set
# CONFIG_USB_NET_ZAURUS is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
# Graphics support
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+CONFIG_FB_SYS_FILLRECT=y
+CONFIG_FB_SYS_COPYAREA=y
+CONFIG_FB_SYS_IMAGEBLIT=y
+CONFIG_FB_SYS_FOPS=y
CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set
+# CONFIG_SND_USB_CAIAQ is not set
#
-# SoC audio support
+# System on Chip audio support
#
# CONFIG_SND_SOC is not set
#
# CONFIG_DLM is not set
# CONFIG_UCC_SLOW is not set
-# CONFIG_UCC_FAST is not set
#
# Library routines
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.20-rc5
-# Mon Jan 22 22:31:27 2007
+# Linux kernel version: 2.6.22-rc6
+# Tue Jun 26 14:17:45 2007
#
CONFIG_PPC64=y
CONFIG_64BIT=y
# CONFIG_PPC_OF_PLATFORM_PCI is not set
CONFIG_ALTIVEC=y
CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_MM_SLICES=y
CONFIG_VIRT_CPU_ACCOUNTING=y
CONFIG_SMP=y
CONFIG_NR_CPUS=128
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
# CONFIG_UTS_NS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=17
CONFIG_CPUSETS=y
CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_EMBEDDED6xx is not set
# CONFIG_APUS is not set
CONFIG_PPC_PSERIES=y
+CONFIG_PPC_SPLPAR=y
+CONFIG_EEH=y
+CONFIG_SCANLOG=m
+CONFIG_LPARCFG=y
# CONFIG_PPC_ISERIES is not set
# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
# CONFIG_PPC_PMAC is not set
# CONFIG_PPC_MAPLE is not set
# CONFIG_PPC_PASEMI is not set
+# CONFIG_PPC_CELLEB is not set
+# CONFIG_PPC_PS3 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_IBM_CELL_BLADE is not set
-# CONFIG_PPC_PS3 is not set
+# CONFIG_PQ2ADS is not set
CONFIG_PPC_NATIVE=y
# CONFIG_UDBG_RTAS_CONSOLE is not set
CONFIG_XICS=y
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+CONFIG_PPC_I8259=y
# CONFIG_U3_DART is not set
CONFIG_PPC_RTAS=y
CONFIG_RTAS_ERROR_LOGGING=y
# CONFIG_PPC_INDIRECT_IO is not set
# CONFIG_GENERIC_IOMAP is not set
# CONFIG_CPU_FREQ is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_MPIC=y
+# CONFIG_CPM2 is not set
#
# Kernel options
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
-CONFIG_PPC_SPLPAR=y
-CONFIG_EEH=y
-CONFIG_SCANLOG=m
-CONFIG_LPARCFG=y
CONFIG_NUMA=y
CONFIG_NODES_SHIFT=4
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_NODES_SPAN_OTHER_NODES=y
+# CONFIG_PPC_HAS_HASH_64K is not set
# CONFIG_PPC_64K_PAGES is not set
CONFIG_SCHED_SMT=y
CONFIG_PROC_DEVICETREE=y
# CONFIG_CMDLINE_BOOL is not set
# CONFIG_PM is not set
CONFIG_SECCOMP=y
+# CONFIG_WANT_DEVICE_TREE is not set
CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
-# CONFIG_MPIC_WEIRD is not set
-CONFIG_PPC_I8259=y
# CONFIG_PPC_INDIRECT_PCI is not set
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
-
-#
-# PCI Hotplug Support
-#
CONFIG_HOTPLUG_PCI=m
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
CONFIG_NF_CONNTRACK_ENABLED=m
-CONFIG_NF_CONNTRACK_SUPPORT=y
-# CONFIG_IP_NF_CONNTRACK_SUPPORT is not set
CONFIG_NF_CONNTRACK=m
-# CONFIG_NF_CT_ACCT is not set
+CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
# CONFIG_NF_CT_PROTO_SCTP is not set
CONFIG_NF_CONNTRACK_IRC=m
# CONFIG_NF_CONNTRACK_NETBIOS_NS is not set
# CONFIG_NF_CONNTRACK_PPTP is not set
+# CONFIG_NF_CONNTRACK_SANE is not set
# CONFIG_NF_CONNTRACK_SIP is not set
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
-# CONFIG_NETFILTER_XTABLES is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
#
# IP: Netfilter Configuration
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_IPRANGE=m
+CONFIG_IP_NF_MATCH_TOS=m
+CONFIG_IP_NF_MATCH_RECENT=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_MATCH_OWNER=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_SAME=m
+CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+CONFIG_NF_NAT_TFTP=m
+# CONFIG_NF_NAT_AMANDA is not set
+# CONFIG_NF_NAT_PPTP is not set
+# CONFIG_NF_NAT_H323 is not set
+# CONFIG_NF_NAT_SIP is not set
+# CONFIG_IP_NF_MANGLE is not set
+# CONFIG_IP_NF_RAW is not set
+# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
+CONFIG_NET_CLS_ROUTE=y
#
# Network testing
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
#
# Device Drivers
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
#
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# Misc devices
#
+# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLINK is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
#
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
CONFIG_ATA=y
+# CONFIG_ATA_NONSTANDARD is not set
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
CONFIG_DM_MULTIPATH_EMC=m
+# CONFIG_DM_DELAY is not set
#
# Fusion MPT device support
#
# IEEE 1394 (FireWire) support
#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
#
# Network device support
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
#
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
+# CONFIG_SC92031 is not set
# CONFIG_NET_POCKET is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
CONFIG_ACENIC=y
CONFIG_ACENIC_OMIT_TIGON_I=y
# CONFIG_DL2K is not set
CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
CONFIG_EHEA=m
CONFIG_IXGB=m
# CONFIG_IXGB_NAPI is not set
# CONFIG_S2IO_NAPI is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_PASEMI_MAC is not set
+# CONFIG_MLX4_CORE is not set
CONFIG_TR=y
CONFIG_IBMOL=y
# CONFIG_3C359 is not set
# CONFIG_TMS380TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
#
-# Wan interfaces
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
CONFIG_NETPOLL=y
-CONFIG_NETPOLL_RX=y
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_LIFEBOOK=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_UINPUT is not set
#
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_ICOM=m
CONFIG_SERIAL_JSM=m
+# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_AGP is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
-# CONFIG_I2C_PCA_ISA is not set
#
# Miscellaneous I2C Chip support
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
+# CONFIG_HWMON is not set
#
-# Hardware Monitoring support
+# Multifunction device drivers
#
-# CONFIG_HWMON is not set
-# CONFIG_HWMON_VID is not set
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-# CONFIG_USB_DABUSB is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_LCD_CLASS_DEVICE=m
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+# CONFIG_VGASTATE is not set
CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_SYS_FOPS is not set
+CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SVGALIB is not set
CONFIG_FB_MACMODES=y
-# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_MATROX_MULTIHEAD=y
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
+CONFIG_FB_RADEON_BACKLIGHT=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
CONFIG_FB_IBM_GXT4500=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-
-#
-# Logo configuration
-#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=m
-CONFIG_BACKLIGHT_DEVICE=y
-CONFIG_LCD_CLASS_DEVICE=m
-CONFIG_LCD_DEVICE=y
#
# Sound
# HID Devices
#
CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+CONFIG_USB_HIDDEV=y
#
# USB support
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_ISP116X_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
-CONFIG_USB_HIDDEV=y
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
#
CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
+CONFIG_INFINIBAND_USER_MEM=y
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
+# CONFIG_INFINIBAND_IPATH is not set
CONFIG_INFINIBAND_EHCA=m
-CONFIG_INFINIBAND_EHCA_SCALING=y
# CONFIG_INFINIBAND_AMSO1100 is not set
+# CONFIG_MLX4_INFINIBAND is not set
CONFIG_INFINIBAND_IPOIB=m
+# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
CONFIG_INFINIBAND_SRP=m
#
#
-# Virtualization
+# Auxiliary Display support
#
+# CONFIG_KS0108 is not set
#
# File systems
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
-CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_RPCSEC_GSS_SPKM3=m
# CONFIG_SMB_FS is not set
# Distributed Lock Manager
#
# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
#
# Library routines
CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
+CONFIG_TEXTSEARCH=y
+CONFIG_TEXTSEARCH_KMP=m
+CONFIG_TEXTSEARCH_BM=m
+CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
-CONFIG_IOMAP_COPY=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Instrumentation Support
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
-CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
+# CONFIG_FAULT_INJECTION is not set
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_HCALL_STATS=y
CONFIG_DEBUGGER=y
CONFIG_XMON=y
# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_TWOFISH_COMMON=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_TEST=m
#
*/
discard_lazy_cpu_state();
+ /*
+ * Force reload of FP/VEC.
+ * This has to be done before copying stuff into current->thread.fpr/vr
+ * for the reasons explained in the previous comment.
+ */
+ regs->msr &= ~(MSR_FP | MSR_FE0 | MSR_FE1 | MSR_VEC);
+
err |= __copy_from_user(¤t->thread.fpr, &sc->fp_regs, FP_REGS_SIZE);
#ifdef CONFIG_ALTIVEC
current->thread.vrsave = 0;
#endif /* CONFIG_ALTIVEC */
- /* Force reload of FP/VEC */
- regs->msr &= ~(MSR_FP | MSR_FE0 | MSR_FE1 | MSR_VEC);
-
return err;
}
mr r11,r4 /* r11 saves tz */
bl __get_datapage@local /* get data page */
mr r9, r3 /* datapage ptr in r9 */
+ cmplwi r10,0 /* check if tv is NULL */
+ beq 3f
bl __do_get_xsec@local /* get xsec from tb & kernel */
bne- 2f /* out of line -> do syscall */
mulhwu r5,r5,r6
stw r5,TVAL32_TV_USEC(r10)
- cmpli cr0,r11,0 /* check if tz is NULL */
+3: cmplwi r11,0 /* check if tz is NULL */
beq 1f
lwz r4,CFG_TZ_MINUTEWEST(r9)/* fill tz */
lwz r5,CFG_TZ_DSTTIME(r9)
-
- /*
+/*
* Userland implementation of gettimeofday() for 64 bits processes in a
* ppc64 kernel for use in the vDSO
*
mr r11,r3 /* r11 holds tv */
mr r10,r4 /* r10 holds tz */
bl V_LOCAL_FUNC(__get_datapage) /* get data page */
+ cmpldi r10,0 /* check if tv is NULL */
+ beq 2f
bl V_LOCAL_FUNC(__do_get_xsec) /* get xsec from tb & kernel */
lis r7,15 /* r7 = 1000000 = USEC_PER_SEC */
ori r7,r7,16960
* XSEC_PER_SEC
*/
rldicl r0,r0,44,20
- cmpldi cr0,r10,0 /* check if tz is NULL */
std r0,TVAL64_TV_USEC(r11) /* store usec in tv */
+2: cmpldi r10,0 /* check if tz is NULL */
beq 1f
lwz r4,CFG_TZ_MINUTEWEST(r3)/* fill tz */
lwz r5,CFG_TZ_DSTTIME(r3)
struct list_head *l;
rh_block_t *blk;
rh_block_t *newblk;
- unsigned long start;
+ unsigned long start, sp_size;
/* Validate size, and alignment must be power of two */
if (size <= 0 || (alignment & (alignment - 1)) != 0)
return (unsigned long) -EINVAL;
- /* given alignment larger that default rheap alignment */
- if (alignment > info->alignment)
- size += alignment - 1;
-
/* Align to configured alignment */
size = (size + (info->alignment - 1)) & ~(info->alignment - 1);
- if (assure_empty(info, 1) < 0)
+ if (assure_empty(info, 2) < 0)
return (unsigned long) -ENOMEM;
blk = NULL;
list_for_each(l, &info->free_list) {
blk = list_entry(l, rh_block_t, list);
- if (size <= blk->size)
- break;
+ if (size <= blk->size) {
+ start = (blk->start + alignment - 1) & ~(alignment - 1);
+ if (start + size <= blk->start + blk->size)
+ break;
+ }
blk = NULL;
}
list_del(&blk->list);
newblk = blk;
} else {
+ /* Fragment caused, split if needed */
+ /* Create block for fragment in the beginning */
+ sp_size = start - blk->start;
+ if (sp_size) {
+ rh_block_t *spblk;
+
+ spblk = get_slot(info);
+ spblk->start = blk->start;
+ spblk->size = sp_size;
+ /* add before the blk */
+ list_add(&spblk->list, blk->list.prev);
+ }
newblk = get_slot(info);
- newblk->start = blk->start;
+ newblk->start = start;
newblk->size = size;
- /* blk still in free list, with updated start, size */
- blk->start += size;
- blk->size -= size;
+ /* blk still in free list, with updated start and size
+ * for fragment in the end */
+ blk->start = start + size;
+ blk->size -= sp_size + size;
+ /* No fragment in the end, remove blk */
+ if (blk->size == 0) {
+ list_del(&blk->list);
+ release_slot(info, blk);
+ }
}
newblk->owner = owner;
- start = newblk->start;
attach_taken_block(info, newblk);
- /* for larger alignment return fixed up pointer */
- /* this is no problem with the deallocator since */
- /* we scan for pointers that lie in the blocks */
- if (alignment > info->alignment)
- start = (start + alignment - 1) & ~(alignment - 1);
-
return start;
}
#endif /* CONFIG_8xx */
if (is_exec) {
-#ifdef CONFIG_PPC64
+#if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE))
/* protection fault */
if (error_code & DSISR_PROTFAULT)
goto bad_area;
if (!(vma->vm_flags & VM_EXEC))
goto bad_area;
-#endif
-#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
+#else
pte_t *ptep;
pmd_t *pmdp;
static int pmac_late_init(void)
{
+ if (!machine_is(powermac))
+ return -ENODEV;
+
initializing = 0;
/* this is udbg (which is __init) and we can later use it during
* cpu hotplug (in smp_core99_kick_cpu) */
/******************************* init / exit *********************************/
-static void
-appldata_online_cpu(int cpu)
+static void __cpuinit appldata_online_cpu(int cpu)
{
init_virt_timer(&per_cpu(appldata_timer, cpu));
per_cpu(appldata_timer, cpu).function = appldata_timer_function;
return NOTIFY_OK;
}
-static struct notifier_block appldata_nb = {
+static struct notifier_block __cpuinitdata appldata_nb = {
.notifier_call = appldata_cpu_notify,
};
RESTORE_ALL __LC_RETURN_MCCK_PSW,0
-#ifdef CONFIG_SMP
/*
* Restart interruption handler, kick starter for additional CPUs
*/
+#ifdef CONFIG_SMP
+#ifndef CONFIG_HOTPLUG_CPU
+ .section .init.text,"ax"
+#endif
.globl restart_int_handler
restart_int_handler:
l %r15,__LC_SAVE_AREA+60 # load ksp
br %r14 # branch to start_secondary
restart_addr:
.long start_secondary
+#ifndef CONFIG_HOTPLUG_CPU
+ .previous
+#endif
#else
/*
* If we do not run with SMP enabled, let the new CPU crash ...
#endif
lpswe __LC_RETURN_MCCK_PSW # back to caller
-#ifdef CONFIG_SMP
/*
* Restart interruption handler, kick starter for additional CPUs
*/
+#ifdef CONFIG_SMP
+#ifndef CONFIG_HOTPLUG_CPU
+ .section .init.text,"ax"
+#endif
.globl restart_int_handler
restart_int_handler:
lg %r15,__LC_SAVE_AREA+120 # load ksp
lmg %r6,%r15,__SF_GPRS(%r15) # load registers from clone
stosm __SF_EMPTY(%r15),0x04 # now we can turn dat on
jg start_secondary
+#ifndef CONFIG_HOTPLUG_CPU
+ .previous
+#endif
#else
/*
* If we do not run with SMP enabled, let the new CPU crash ...
else
sprintf(str, "cio_ignore=all,!0.0.%04x",
ipl_info.data.fcp.dev_id.devno);
+ strcat(COMMAND_LINE, " ");
strcat(COMMAND_LINE, str);
console_loglevel = 2;
}
{
static int die_counter;
+ oops_enter();
debug_stop_all();
console_verbose();
spin_lock_irq(&die_lock);
bust_spinlocks(1);
printk("%s: %04lx [#%d]\n", str, err & 0xffff, ++die_counter);
- show_regs(regs);
+ print_modules();
+ show_regs(regs);
bust_spinlocks(0);
- spin_unlock_irq(&die_lock);
+ spin_unlock_irq(&die_lock);
if (in_interrupt())
panic("Fatal exception in interrupt");
if (panic_on_oops)
panic("Fatal exception: panic_on_oops");
- do_exit(SIGSEGV);
+ oops_exit();
+ do_exit(SIGSEGV);
}
static void inline
badframe:
force_sig(SIGSEGV, current);
return 0;
-}
+}
/*
* Set up a signal frame.
static int
handle_signal(unsigned long sig, struct k_sigaction *ka, siginfo_t *info,
- sigset_t *oldset, struct pt_regs *regs)
+ sigset_t *oldset, struct pt_regs *regs, unsigned int save_r0)
{
int ret;
if (regs->tra >= 0) {
/* If so, check system call restarting.. */
switch (regs->regs[0]) {
+ case -ERESTART_RESTARTBLOCK:
case -ERESTARTNOHAND:
regs->regs[0] = -EINTR;
break;
}
/* fallthrough */
case -ERESTARTNOINTR:
+ regs->regs[0] = save_r0;
regs->pc -= instruction_size(
ctrl_inw(regs->pc - 4));
break;
signr = get_signal_to_deliver(&info, &ka, regs, NULL);
if (signr > 0) {
/* Whee! Actually deliver the signal. */
- if (handle_signal(signr, &ka, &info, oldset, regs) == 0) {
+ if (handle_signal(signr, &ka, &info, oldset,
+ regs, save_r0) == 0) {
/* a signal was successfully delivered; the saved
* sigmask will have been stored in the signal frame,
* and will be restored by sigreturn, so we can simply
{
static int die_counter;
+ oops_enter();
+
console_verbose();
spin_lock_irq(&die_lock);
bust_spinlocks(1);
if (panic_on_oops)
panic("Fatal exception");
+ oops_exit();
do_exit(SIGSEGV);
}
if (regs->syscall_nr >= 0) {
/* If so, check system call restarting.. */
switch (regs->regs[REG_RET]) {
+ case -ERESTART_RESTARTBLOCK:
case -ERESTARTNOHAND:
regs->regs[REG_RET] = -EINTR;
break;
.quad quiet_ni_syscall /* tux */
.quad quiet_ni_syscall /* security */
.quad sys_gettid
- .quad sys_readahead /* 225 */
+ .quad sys32_readahead /* 225 */
.quad sys_setxattr
.quad sys_lsetxattr
.quad sys_fsetxattr
.quad compat_sys_io_getevents
.quad compat_sys_io_submit
.quad sys_io_cancel
- .quad sys_fadvise64 /* 250 */
+ .quad sys32_fadvise64 /* 250 */
.quad quiet_ni_syscall /* free_huge_pages */
.quad sys_exit_group
.quad sys32_lookup_dcookie
.quad compat_sys_set_robust_list
.quad compat_sys_get_robust_list
.quad sys_splice
- .quad sys_sync_file_range
+ .quad sys32_sync_file_range
.quad sys_tee /* 315 */
.quad compat_sys_vmsplice
.quad compat_sys_move_pages
return sys_lookup_dcookie(((u64)addr_high << 32) | addr_low, buf, len);
}
+asmlinkage ssize_t sys32_readahead(int fd, unsigned off_lo, unsigned off_hi, size_t count)
+{
+ return sys_readahead(fd, ((u64)off_hi << 32) | off_lo, count);
+}
+
+asmlinkage long sys32_sync_file_range(int fd, unsigned off_low, unsigned off_hi,
+ unsigned n_low, unsigned n_hi, int flags)
+{
+ return sys_sync_file_range(fd,
+ ((u64)off_hi << 32) | off_low,
+ ((u64)n_hi << 32) | n_low, flags);
+}
+
+asmlinkage long sys32_fadvise64(int fd, unsigned offset_lo, unsigned offset_hi, size_t len,
+ int advice)
+{
+ return sys_fadvise64_64(fd, ((u64)offset_hi << 32) | offset_lo,
+ len, advice);
+}
ret
CFI_ENDPROC
ENDPROC(call_softirq)
+
+KPROBE_ENTRY(ignore_sysret)
+ CFI_STARTPROC
+ mov $-ENOSYS,%eax
+ sysret
+ CFI_ENDPROC
+ENDPROC(ignore_sysret)
for (i = 0; i < next; i++) {
unsigned long start = jiffies;
while (!mcelog.entry[i].finished) {
- if (!time_before(jiffies, start + 2)) {
+ if (time_after_eq(jiffies, start + 2)) {
memset(mcelog.entry + i,0, sizeof(struct mce));
- continue;
+ goto timeout;
}
cpu_relax();
}
smp_rmb();
err |= copy_to_user(buf, mcelog.entry + i, sizeof(struct mce));
buf += sizeof(struct mce);
+ timeout:
+ ;
}
memset(mcelog.entry, 0, next * sizeof(struct mce));
return 0;
}
+#ifdef CONFIG_PCI
+/* Many VIA bridges seem to corrupt data for DAC. Disable it here */
+
+static __devinit void via_no_dac(struct pci_dev *dev)
+{
+ if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI && forbid_dac == 0) {
+ printk(KERN_INFO "PCI: VIA PCI bridge detected. Disabling DAC.\n");
+ forbid_dac = 1;
+ }
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_ANY_ID, via_no_dac);
+#endif
/* Must execute after PCI subsystem */
fs_initcall(pci_iommu_init);
char boot_exception_stacks[(N_EXCEPTION_STACKS - 1) * EXCEPTION_STKSZ + DEBUG_STKSZ]
__attribute__((section(".bss.page_aligned")));
+extern asmlinkage void ignore_sysret(void);
+
/* May not be marked __init: used by software suspend */
void syscall_init(void)
{
*/
wrmsrl(MSR_STAR, ((u64)__USER32_CS)<<48 | ((u64)__KERNEL_CS)<<32);
wrmsrl(MSR_LSTAR, system_call);
+ wrmsrl(MSR_CSTAR, ignore_sysret);
#ifdef CONFIG_IA32_EMULATION
syscall32_cpu_init ();
if (num_possible_cpus() > 1)
start = (unsigned long)_etext;
#endif
+
+#ifdef CONFIG_KPROBES
+ start = (unsigned long)__start_rodata;
+#endif
+
end = (unsigned long)__end_rodata;
start = (start + PAGE_SIZE - 1) & PAGE_MASK;
end &= PAGE_MASK;
struct page *pg;
/* When clflush is available always use it because it is
- much cheaper than WBINVD */
- if (!cpu_has_clflush)
+ much cheaper than WBINVD. Disable clflush for now because
+ the high level code is not ready yet */
+ if (1 || !cpu_has_clflush)
asm volatile("wbinvd" ::: "memory");
- list_for_each_entry(pg, l, lru) {
+ else list_for_each_entry(pg, l, lru) {
void *adr = page_address(pg);
if (cpu_has_clflush)
cache_flush_page(adr);
int sleep_ticks = 0;
u32 t1, t2 = 0;
- pr = processors[smp_processor_id()];
- if (!pr)
- return;
-
/*
* Interrupts must be disabled during bus mastering calculations and
* for C2/C3 transitions.
*/
local_irq_disable();
+ pr = processors[smp_processor_id()];
+ if (!pr) {
+ local_irq_enable();
+ return;
+ }
+
/*
* Check whether we truly need to go idle, or should
* reschedule:
{
struct acpi_thermal *tz = seq->private;
struct acpi_device *device;
+ acpi_status status;
+
int i = 0;
int j = 0;
tz->trips.passive.tc1, tz->trips.passive.tc2,
tz->trips.passive.tsp);
for (j = 0; j < tz->trips.passive.devices.count; j++) {
- acpi_bus_get_device(tz->trips.passive.devices.handles[j], &device);
- seq_printf(seq, "%4.4s ", acpi_device_bid(device));
+ status = acpi_bus_get_device(tz->trips.passive.devices.
+ handles[j], &device);
+ seq_printf(seq, "%4.4s ", status ? "" :
+ acpi_device_bid(device));
}
seq_puts(seq, "\n");
}
i,
KELVIN_TO_CELSIUS(tz->trips.active[i].temperature));
for (j = 0; j < tz->trips.active[i].devices.count; j++){
- acpi_bus_get_device(tz->trips.active[i].devices.handles[j], &device);
- seq_printf(seq, "%4.4s ", acpi_device_bid(device));
+ status = acpi_bus_get_device(tz->trips.active[i].
+ devices.handles[j],
+ &device);
+ seq_printf(seq, "%4.4s ", status ? "" :
+ acpi_device_bid(device));
}
seq_puts(seq, "\n");
}
package_elements = ACPI_ALLOCATE_ZEROED((acpi_size)
(count + 1) * sizeof(void *));
if (!package_elements) {
- ACPI_FREE(package_desc);
+ acpi_ut_remove_reference(package_desc);
return_PTR(NULL);
}
/* fixup zero port_map */
if (!port_map) {
- port_map = (1 << ahci_nr_ports(hpriv->cap)) - 1;
+ port_map = (1 << ahci_nr_ports(cap)) - 1;
dev_printk(KERN_WARNING, &pdev->dev,
"PORTS_IMPL is zero, forcing 0x%x\n", port_map);
/**
* ata_dev_reread_id - Re-read IDENTIFY data
- * @adev: target ATA device
+ * @dev: target ATA device
* @readid_flags: read ID flags
*
* Re-read IDENTIFY page and make sure @dev is still attached to
{ "HTS541010G9SA00", "MBZOC60D", ATA_HORKAGE_NONCQ, },
/* Drives which do spurious command completion */
{ "HTS541680J9SA00", "SB2IC7EP", ATA_HORKAGE_NONCQ, },
+ { "HTS541612J9SA00", "SBDIC7JP", ATA_HORKAGE_NONCQ, },
+ { "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, },
/* Devices with NCQ limits */
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 8 },
+ { PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 8 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 9 },
{ },
* pata_it821x.c - IT821x PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@redhat.com>
+ * (C) 2007 Bartlomiej Zolnierkiewicz
*
* based upon
*
#define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.3.6"
+#define DRV_VERSION "0.3.7"
struct it821x_dev
{
static int it821x_smart_set_mode(struct ata_port *ap, struct ata_device **unused)
{
- int dma_enabled = 0;
int i;
- /* Bits 5 and 6 indicate if DMA is active on master/slave */
- /* It is possible that BMDMA isn't allocated */
- if (ap->ioaddr.bmdma_addr)
- dma_enabled = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
-
for (i = 0; i < ATA_MAX_DEVICES; i++) {
struct ata_device *dev = &ap->device[i];
if (ata_dev_enabled(dev)) {
dev->dma_mode = XFER_MW_DMA_0;
/* We do need the right mode information for DMA or PIO
and this comes from the current configuration flags */
- if (dma_enabled & (1 << (5 + i))) {
+ if (ata_id_has_dma(dev->id)) {
ata_dev_printk(dev, KERN_INFO, "configured for DMA\n");
dev->xfer_mode = XFER_MW_DMA_0;
dev->xfer_shift = ATA_SHIFT_MWDMA;
module_param_named(noraid, it8212_noraid, int, S_IRUGO);
-MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
+MODULE_PARM_DESC(noraid, "Force card into bypass mode");
module_init(it821x_init);
module_exit(it821x_exit);
&intel_845_driver, &intel_830_driver },
{ PCI_DEVICE_ID_INTEL_82875_HB, 0, 0, "i875", &intel_845_driver, NULL },
{ PCI_DEVICE_ID_INTEL_82915G_HB, PCI_DEVICE_ID_INTEL_82915G_IG, 0, "915G",
- &intel_845_driver, &intel_915_driver },
+ NULL, &intel_915_driver },
{ PCI_DEVICE_ID_INTEL_82915GM_HB, PCI_DEVICE_ID_INTEL_82915GM_IG, 0, "915GM",
- &intel_845_driver, &intel_915_driver },
+ NULL, &intel_915_driver },
{ PCI_DEVICE_ID_INTEL_82945G_HB, PCI_DEVICE_ID_INTEL_82945G_IG, 0, "945G",
- &intel_845_driver, &intel_915_driver },
+ NULL, &intel_915_driver },
{ PCI_DEVICE_ID_INTEL_82945GM_HB, PCI_DEVICE_ID_INTEL_82945GM_IG, 1, "945GM",
- &intel_845_driver, &intel_915_driver },
+ NULL, &intel_915_driver },
{ PCI_DEVICE_ID_INTEL_82945GM_HB, PCI_DEVICE_ID_INTEL_82945GME_IG, 0, "945GME",
- &intel_845_driver, &intel_915_driver },
+ NULL, &intel_915_driver },
{ PCI_DEVICE_ID_INTEL_82946GZ_HB, PCI_DEVICE_ID_INTEL_82946GZ_IG, 0, "946GZ",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_82965G_1_HB, PCI_DEVICE_ID_INTEL_82965G_1_IG, 0, "965G",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_82965Q_HB, PCI_DEVICE_ID_INTEL_82965Q_IG, 0, "965Q",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_82965G_HB, PCI_DEVICE_ID_INTEL_82965G_IG, 0, "965G",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_82965GM_HB, PCI_DEVICE_ID_INTEL_82965GM_IG, 1, "965GM",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_82965GM_HB, PCI_DEVICE_ID_INTEL_82965GME_IG, 0, "965GME/GLE",
- &intel_845_driver, &intel_i965_driver },
+ NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_7505_0, 0, 0, "E7505", &intel_7505_driver, NULL },
{ PCI_DEVICE_ID_INTEL_7205_0, 0, 0, "E7205", &intel_7505_driver, NULL },
{ PCI_DEVICE_ID_INTEL_G33_HB, PCI_DEVICE_ID_INTEL_G33_IG, 0, "G33",
- &intel_845_driver, &intel_g33_driver },
+ NULL, &intel_g33_driver },
{ PCI_DEVICE_ID_INTEL_Q35_HB, PCI_DEVICE_ID_INTEL_Q35_IG, 0, "Q35",
- &intel_845_driver, &intel_g33_driver },
+ NULL, &intel_g33_driver },
{ PCI_DEVICE_ID_INTEL_Q33_HB, PCI_DEVICE_ID_INTEL_Q33_IG, 0, "Q33",
- &intel_845_driver, &intel_g33_driver },
+ NULL, &intel_g33_driver },
{ 0, 0, 0, NULL, NULL, NULL }
};
}
if (bridge->driver == NULL) {
- printk(KERN_WARNING PFX "Failed to find bridge device "
- "(chip_id: %04x)\n", intel_agp_chipsets[i].gmch_chip_id);
+ /* bridge has no AGP and no IGD detected */
+ if (cap_ptr)
+ printk(KERN_WARNING PFX "Failed to find bridge device "
+ "(chip_id: %04x)\n",
+ intel_agp_chipsets[i].gmch_chip_id);
agp_put_bridge(bridge);
return -ENODEV;
}
brdp->ioaddr2 = conf.ioaddr2;
brdp->irq = conf.irq;
brdp->irqtype = conf.irqtype;
- if (stl_brdinit(brdp))
+ stl_brds[brdp->brdnr] = brdp;
+ if (stl_brdinit(brdp)) {
+ stl_brds[brdp->brdnr] = NULL;
kfree(brdp);
- else {
+ } else {
for (j = 0; j < brdp->nrports; j++)
tty_register_device(stl_serial,
brdp->brdnr * STL_MAXPORTS + j, NULL);
- stl_brds[brdp->brdnr] = brdp;
stl_nrbrds = i + 1;
}
}
DEFINE_MUTEX(con_buf_mtx);
/* is_double_width() is based on the wcwidth() implementation by
- * Markus Kuhn -- 2003-05-20 (Unicode 4.0)
+ * Markus Kuhn -- 2007-05-26 (Unicode 5.0)
* Latest version: http://www.cl.cam.ac.uk/~mgk25/ucs/wcwidth.c
*/
struct interval {
static const struct interval double_width[] = {
{ 0x1100, 0x115F }, { 0x2329, 0x232A }, { 0x2E80, 0x303E },
{ 0x3040, 0xA4CF }, { 0xAC00, 0xD7A3 }, { 0xF900, 0xFAFF },
- { 0xFE30, 0xFE6F }, { 0xFF00, 0xFF60 }, { 0xFFE0, 0xFFE6 },
- { 0x20000, 0x2FFFD }, { 0x30000, 0x3FFFD }
+ { 0xFE10, 0xFE19 }, { 0xFE30, 0xFE6F }, { 0xFF00, 0xFF60 },
+ { 0xFFE0, 0xFFE6 }, { 0x20000, 0x2FFFD }, { 0x30000, 0x3FFFD }
};
return bisearch(ucs, double_width,
sizeof(double_width) / sizeof(*double_width) - 1);
continue; /* nothing to display */
}
/* Glyph not found */
- if (!(vc->vc_utf && !vc->vc_disp_ctrl) && !(c & ~charmask)) {
+ if ((!(vc->vc_utf && !vc->vc_disp_ctrl) || c < 128) && !(c & ~charmask)) {
/* In legacy mode use the glyph we get by a 1:1 mapping.
- This would make absolutely no sense with Unicode in mind. */
+ This would make absolutely no sense with Unicode in mind,
+ but do this for ASCII characters since a font may lack
+ Unicode mapping info and we don't want to end up with
+ having question marks only. */
tc = c;
} else {
/* Display U+FFFD. If it's not found, display an inverse question mark. */
} else {
vc_attr = ((vc->vc_attr) & 0x88) | (((vc->vc_attr) & 0x70) >> 4) | (((vc->vc_attr) & 0x07) << 4);
}
+ FLUSH
}
while (1) {
if (tc < 0) tc = ' ';
}
+ if (inverse) {
+ FLUSH
+ }
+
if (rescan) {
rescan = 0;
inverse = 0;
static int ioctl_create_iso_context(struct client *client, void *buffer)
{
struct fw_cdev_create_iso_context *request = buffer;
+ struct fw_iso_context *context;
if (request->channel > 63)
return -EINVAL;
return -EINVAL;
}
+ context = fw_iso_context_create(client->device->card,
+ request->type,
+ request->channel,
+ request->speed,
+ request->header_size,
+ iso_callback, client);
+ if (IS_ERR(context))
+ return PTR_ERR(context);
+
client->iso_closure = request->closure;
- client->iso_context = fw_iso_context_create(client->device->card,
- request->type,
- request->channel,
- request->speed,
- request->header_size,
- iso_callback, client);
- if (IS_ERR(client->iso_context))
- return PTR_ERR(client->iso_context);
+ client->iso_context = context;
/* We only support one context at this time. */
request->handle = 0;
event = reg_read(ohci, OHCI1394_IntEventClear);
- if (!event)
+ if (!event || !~event)
return IRQ_NONE;
reg_write(ohci, OHCI1394_IntEventClear, event);
/* check for microcode update */
rdmsr_on_cpu(data->id, MSR_IA32_UCODE_REV, &eax, &edx);
if (edx < 0x39) {
+ err = -ENODEV;
dev_err(&pdev->dev,
"Errata AE18 not fixed, update BIOS or "
"microcode of the CPU!\n");
/* Transmit a packet (called by kernel) */
static int ether1394_tx(struct sk_buff *skb, struct net_device *dev)
{
- struct eth1394hdr *eth;
+ struct eth1394hdr hdr_buf;
struct eth1394_priv *priv = netdev_priv(dev);
__be16 proto;
unsigned long flags;
if (!skb)
goto fail;
- /* Get rid of the fake eth1394 header, but save a pointer */
- eth = (struct eth1394hdr *)skb->data;
+ /* Get rid of the fake eth1394 header, but first make a copy.
+ * We might need to rebuild the header on tx failure. */
+ memcpy(&hdr_buf, skb->data, sizeof(hdr_buf));
skb_pull(skb, ETH1394_HLEN);
- proto = eth->h_proto;
+ proto = hdr_buf.h_proto;
dg_size = skb->len;
/* Set the transmission type for the packet. ARP packets and IP
* broadcast packets are sent via GASP. */
- if (memcmp(eth->h_dest, dev->broadcast, ETH1394_ALEN) == 0 ||
+ if (memcmp(hdr_buf.h_dest, dev->broadcast, ETH1394_ALEN) == 0 ||
proto == htons(ETH_P_ARP) ||
(proto == htons(ETH_P_IP) &&
IN_MULTICAST(ntohl(ip_hdr(skb)->daddr)))) {
if (max_payload < dg_size + hdr_type_len[ETH1394_HDR_LF_UF])
priv->bc_dgl++;
} else {
- __be64 guid = get_unaligned((u64 *)eth->h_dest);
+ __be64 guid = get_unaligned((u64 *)hdr_buf.h_dest);
node = eth1394_find_node_guid(&priv->ip_node_list,
be64_to_cpu(guid));
if (dest_node == (LOCAL_BUS | ALL_NODES))
goto fail;
+ /* At this point we want to restore the packet. When we return
+ * here with NETDEV_TX_BUSY we will get another entrance in this
+ * routine with the same skb and we need it to look the same.
+ * So we pull 4 more bytes, then build the header again. */
+ skb_pull(skb, 4);
+ ether1394_header(skb, dev, ntohs(hdr_buf.h_proto),
+ hdr_buf.h_dest, NULL, 0);
+
/* Most failures of ether1394_send_packet are recoverable. */
netif_stop_queue(dev);
priv->wake_node = dest_node;
* up here and not be able to take the mmap_sem. In that case
* we defer the vm_locked accounting to the system workqueue.
*/
- if (context->closing && !down_write_trylock(&mm->mmap_sem)) {
- INIT_WORK(&umem->work, ib_umem_account);
- umem->mm = mm;
- umem->diff = diff;
-
- schedule_work(&umem->work);
- return;
+ if (context->closing) {
+ if (!down_write_trylock(&mm->mmap_sem)) {
+ INIT_WORK(&umem->work, ib_umem_account);
+ umem->mm = mm;
+ umem->diff = diff;
+
+ schedule_work(&umem->work);
+ return;
+ }
} else
down_write(&mm->mmap_sem);
if (is_send) {
wq = &(*cur_qp)->sq;
wqe_ctr = be16_to_cpu(cqe->wqe_index);
- wq->tail += wqe_ctr - (u16) wq->tail;
- wc->wr_id = wq->wrid[wq->tail & (wq->max - 1)];
+ wq->tail += (u16) (wqe_ctr - (u16) wq->tail);
+ wc->wr_id = wq->wrid[wq->tail & (wq->wqe_cnt - 1)];
++wq->tail;
} else if ((*cur_qp)->ibqp.srq) {
srq = to_msrq((*cur_qp)->ibqp.srq);
mlx4_ib_free_srq_wqe(srq, wqe_ctr);
} else {
wq = &(*cur_qp)->rq;
- wc->wr_id = wq->wrid[wq->tail & (wq->max - 1)];
+ wc->wr_id = wq->wrid[wq->tail & (wq->wqe_cnt - 1)];
++wq->tail;
}
{
u32 prod_index;
int nfreed = 0;
- struct mlx4_cqe *cqe;
+ struct mlx4_cqe *cqe, *dest;
+ u8 owner_bit;
/*
* First we need to find the current producer index, so we
if (srq && !(cqe->owner_sr_opcode & MLX4_CQE_IS_SEND_MASK))
mlx4_ib_free_srq_wqe(srq, be16_to_cpu(cqe->wqe_index));
++nfreed;
- } else if (nfreed)
- memcpy(get_cqe(cq, (prod_index + nfreed) & cq->ibcq.cqe),
- cqe, sizeof *cqe);
+ } else if (nfreed) {
+ dest = get_cqe(cq, (prod_index + nfreed) & cq->ibcq.cqe);
+ owner_bit = dest->owner_sr_opcode & MLX4_CQE_OWNER_MASK;
+ memcpy(dest, cqe, sizeof *cqe);
+ dest->owner_sr_opcode = owner_bit |
+ (dest->owner_sr_opcode & ~MLX4_CQE_OWNER_MASK);
+ }
}
if (nfreed) {
props->max_qp_init_rd_atom = dev->dev->caps.max_qp_init_rdma;
props->max_res_rd_atom = props->max_qp_rd_atom * props->max_qp;
props->max_srq = dev->dev->caps.num_srqs - dev->dev->caps.reserved_srqs;
- props->max_srq_wr = dev->dev->caps.max_srq_wqes;
+ props->max_srq_wr = dev->dev->caps.max_srq_wqes - 1;
props->max_srq_sge = dev->dev->caps.max_srq_sge;
props->local_ca_ack_delay = dev->dev->caps.local_ca_ack_delay;
props->atomic_cap = dev->dev->caps.flags & MLX4_DEV_CAP_FLAG_ATOMIC ?
IB_ATOMIC_HCA : IB_ATOMIC_NONE;
- props->max_pkeys = dev->dev->caps.pkey_table_len;
+ props->max_pkeys = dev->dev->caps.pkey_table_len[1];
props->max_mcast_grp = dev->dev->caps.num_mgms + dev->dev->caps.num_amgms;
props->max_mcast_qp_attach = dev->dev->caps.num_qp_per_mgm;
props->max_total_mcast_qp_attach = props->max_mcast_qp_attach *
props->state = out_mad->data[32] & 0xf;
props->phys_state = out_mad->data[33] >> 4;
props->port_cap_flags = be32_to_cpup((__be32 *) (out_mad->data + 20));
- props->gid_tbl_len = to_mdev(ibdev)->dev->caps.gid_table_len;
+ props->gid_tbl_len = to_mdev(ibdev)->dev->caps.gid_table_len[port];
props->max_msg_sz = 0x80000000;
- props->pkey_tbl_len = to_mdev(ibdev)->dev->caps.pkey_table_len;
+ props->pkey_tbl_len = to_mdev(ibdev)->dev->caps.pkey_table_len[port];
props->bad_pkey_cntr = be16_to_cpup((__be16 *) (out_mad->data + 46));
props->qkey_viol_cntr = be16_to_cpup((__be16 *) (out_mad->data + 48));
props->active_width = out_mad->data[31] & 0xf;
return PTR_ERR(mailbox);
memset(mailbox->buf, 0, 256);
- *(u8 *) mailbox->buf = !!reset_qkey_viols << 6;
- ((__be32 *) mailbox->buf)[2] = cpu_to_be32(cap_mask);
+
+ if (dev->dev->flags & MLX4_FLAG_OLD_PORT_CMDS) {
+ *(u8 *) mailbox->buf = !!reset_qkey_viols << 6;
+ ((__be32 *) mailbox->buf)[2] = cpu_to_be32(cap_mask);
+ } else {
+ ((u8 *) mailbox->buf)[3] = !!reset_qkey_viols;
+ ((__be32 *) mailbox->buf)[1] = cpu_to_be32(cap_mask);
+ }
err = mlx4_cmd(dev->dev, mailbox->dma, port, 0, MLX4_CMD_SET_PORT,
MLX4_CMD_TIME_CLASS_B);
struct mlx4_ib_wq {
u64 *wrid;
spinlock_t lock;
- int max;
+ int wqe_cnt;
+ int max_post;
int max_gs;
int offset;
int wqe_shift;
u32 doorbell_qpn;
__be32 sq_signal_bits;
+ int sq_spare_wqes;
struct mlx4_ib_wq sq;
struct ib_umem *umem;
u8 alt_port;
u8 atomic_rd_en;
u8 resp_depth;
+ u8 sq_no_prefetch;
u8 state;
};
return get_wqe(qp, qp->sq.offset + (n << qp->sq.wqe_shift));
}
+/*
+ * Stamp a SQ WQE so that it is invalid if prefetched by marking the
+ * first four bytes of every 64 byte chunk with 0xffffffff, except for
+ * the very first chunk of the WQE.
+ */
+static void stamp_send_wqe(struct mlx4_ib_qp *qp, int n)
+{
+ u32 *wqe = get_send_wqe(qp, n);
+ int i;
+
+ for (i = 16; i < 1 << (qp->sq.wqe_shift - 2); i += 16)
+ wqe[i] = 0xffffffff;
+}
+
static void mlx4_ib_qp_event(struct mlx4_qp *qp, enum mlx4_event type)
{
struct ib_event event;
case IB_QPT_GSI:
return sizeof (struct mlx4_wqe_ctrl_seg) +
ALIGN(MLX4_IB_UD_HEADER_SIZE +
+ DIV_ROUND_UP(MLX4_IB_UD_HEADER_SIZE,
+ MLX4_INLINE_ALIGN) *
sizeof (struct mlx4_wqe_inline_seg),
sizeof (struct mlx4_wqe_data_seg)) +
ALIGN(4 +
if (cap->max_recv_wr)
return -EINVAL;
- qp->rq.max = qp->rq.max_gs = 0;
+ qp->rq.wqe_cnt = qp->rq.max_gs = 0;
} else {
/* HW requires >= 1 RQ entry with >= 1 gather entry */
if (is_user && (!cap->max_recv_wr || !cap->max_recv_sge))
return -EINVAL;
- qp->rq.max = roundup_pow_of_two(max(1, cap->max_recv_wr));
- qp->rq.max_gs = roundup_pow_of_two(max(1, cap->max_recv_sge));
+ qp->rq.wqe_cnt = roundup_pow_of_two(max(1U, cap->max_recv_wr));
+ qp->rq.max_gs = roundup_pow_of_two(max(1U, cap->max_recv_sge));
qp->rq.wqe_shift = ilog2(qp->rq.max_gs * sizeof (struct mlx4_wqe_data_seg));
}
- cap->max_recv_wr = qp->rq.max;
+ cap->max_recv_wr = qp->rq.max_post = qp->rq.wqe_cnt;
cap->max_recv_sge = qp->rq.max_gs;
return 0;
cap->max_send_sge + 2 > dev->dev->caps.max_sq_sg)
return -EINVAL;
- qp->sq.max = cap->max_send_wr ? roundup_pow_of_two(cap->max_send_wr) : 1;
-
qp->sq.wqe_shift = ilog2(roundup_pow_of_two(max(cap->max_send_sge *
sizeof (struct mlx4_wqe_data_seg),
cap->max_inline_data +
qp->sq.max_gs = ((1 << qp->sq.wqe_shift) - send_wqe_overhead(type)) /
sizeof (struct mlx4_wqe_data_seg);
- qp->buf_size = (qp->rq.max << qp->rq.wqe_shift) +
- (qp->sq.max << qp->sq.wqe_shift);
+ /*
+ * We need to leave 2 KB + 1 WQE of headroom in the SQ to
+ * allow HW to prefetch.
+ */
+ qp->sq_spare_wqes = (2048 >> qp->sq.wqe_shift) + 1;
+ qp->sq.wqe_cnt = roundup_pow_of_two(cap->max_send_wr + qp->sq_spare_wqes);
+
+ qp->buf_size = (qp->rq.wqe_cnt << qp->rq.wqe_shift) +
+ (qp->sq.wqe_cnt << qp->sq.wqe_shift);
if (qp->rq.wqe_shift > qp->sq.wqe_shift) {
qp->rq.offset = 0;
- qp->sq.offset = qp->rq.max << qp->rq.wqe_shift;
+ qp->sq.offset = qp->rq.wqe_cnt << qp->rq.wqe_shift;
} else {
- qp->rq.offset = qp->sq.max << qp->sq.wqe_shift;
+ qp->rq.offset = qp->sq.wqe_cnt << qp->sq.wqe_shift;
qp->sq.offset = 0;
}
- cap->max_send_wr = qp->sq.max;
- cap->max_send_sge = qp->sq.max_gs;
- cap->max_inline_data = (1 << qp->sq.wqe_shift) - send_wqe_overhead(type) -
- sizeof (struct mlx4_wqe_inline_seg);
+ cap->max_send_wr = qp->sq.max_post = qp->sq.wqe_cnt - qp->sq_spare_wqes;
+ cap->max_send_sge = qp->sq.max_gs;
+ /* We don't support inline sends for kernel QPs (yet) */
+ cap->max_inline_data = 0;
return 0;
}
static int set_user_sq_size(struct mlx4_ib_qp *qp,
struct mlx4_ib_create_qp *ucmd)
{
- qp->sq.max = 1 << ucmd->log_sq_bb_count;
+ qp->sq.wqe_cnt = 1 << ucmd->log_sq_bb_count;
qp->sq.wqe_shift = ucmd->log_sq_stride;
- qp->buf_size = (qp->rq.max << qp->rq.wqe_shift) +
- (qp->sq.max << qp->sq.wqe_shift);
+ qp->buf_size = (qp->rq.wqe_cnt << qp->rq.wqe_shift) +
+ (qp->sq.wqe_cnt << qp->sq.wqe_shift);
return 0;
}
goto err;
}
+ qp->sq_no_prefetch = ucmd.sq_no_prefetch;
+
err = set_user_sq_size(qp, &ucmd);
if (err)
goto err;
goto err_mtt;
}
} else {
+ qp->sq_no_prefetch = 0;
+
err = set_kernel_sq_size(dev, &init_attr->cap, init_attr->qp_type, qp);
if (err)
goto err;
if (err)
goto err_mtt;
- qp->sq.wrid = kmalloc(qp->sq.max * sizeof (u64), GFP_KERNEL);
- qp->rq.wrid = kmalloc(qp->rq.max * sizeof (u64), GFP_KERNEL);
+ qp->sq.wrid = kmalloc(qp->sq.wqe_cnt * sizeof (u64), GFP_KERNEL);
+ qp->rq.wrid = kmalloc(qp->rq.wqe_cnt * sizeof (u64), GFP_KERNEL);
if (!qp->sq.wrid || !qp->rq.wrid) {
err = -ENOMEM;
goto err_wrid;
}
-
- /* We don't support inline sends for kernel QPs (yet) */
- init_attr->cap.max_inline_data = 0;
}
err = mlx4_qp_alloc(dev->dev, sqpn, &qp->mqp);
return 0;
}
-static void init_port(struct mlx4_ib_dev *dev, int port)
-{
- struct mlx4_init_port_param param;
- int err;
-
- memset(¶m, 0, sizeof param);
-
- param.port_width_cap = dev->dev->caps.port_width_cap;
- param.vl_cap = dev->dev->caps.vl_cap;
- param.mtu = ib_mtu_enum_to_int(dev->dev->caps.mtu_cap);
- param.max_gid = dev->dev->caps.gid_table_len;
- param.max_pkey = dev->dev->caps.pkey_table_len;
-
- err = mlx4_INIT_PORT(dev->dev, ¶m, port);
- if (err)
- printk(KERN_WARNING "INIT_PORT failed, return code %d.\n", err);
-}
-
static int to_mlx4_st(enum ib_qp_type type)
{
switch (type) {
path->counter_index = 0xff;
if (ah->ah_flags & IB_AH_GRH) {
- if (ah->grh.sgid_index >= dev->dev->caps.gid_table_len) {
+ if (ah->grh.sgid_index >= dev->dev->caps.gid_table_len[port]) {
printk(KERN_ERR "sgid_index (%u) too large. max is %d\n",
- ah->grh.sgid_index, dev->dev->caps.gid_table_len - 1);
+ ah->grh.sgid_index, dev->dev->caps.gid_table_len[port] - 1);
return -1;
}
context->mtu_msgmax = (attr->path_mtu << 5) | 31;
}
- if (qp->rq.max)
- context->rq_size_stride = ilog2(qp->rq.max) << 3;
+ if (qp->rq.wqe_cnt)
+ context->rq_size_stride = ilog2(qp->rq.wqe_cnt) << 3;
context->rq_size_stride |= qp->rq.wqe_shift - 4;
- if (qp->sq.max)
- context->sq_size_stride = ilog2(qp->sq.max) << 3;
+ if (qp->sq.wqe_cnt)
+ context->sq_size_stride = ilog2(qp->sq.wqe_cnt) << 3;
context->sq_size_stride |= qp->sq.wqe_shift - 4;
+ if (cur_state == IB_QPS_RESET && new_state == IB_QPS_INIT)
+ context->sq_size_stride |= !!qp->sq_no_prefetch << 7;
+
if (qp->ibqp.uobject)
context->usr_page = cpu_to_be32(to_mucontext(ibqp->uobject->context)->uar.index);
else
}
if (attr_mask & IB_QP_ALT_PATH) {
- if (attr->alt_pkey_index >= dev->dev->caps.pkey_table_len)
- return -EINVAL;
-
if (attr->alt_port_num == 0 ||
attr->alt_port_num > dev->dev->caps.num_ports)
return -EINVAL;
+ if (attr->alt_pkey_index >=
+ dev->dev->caps.pkey_table_len[attr->alt_port_num])
+ return -EINVAL;
+
if (mlx4_set_path(dev, &attr->alt_ah_attr, &context->alt_path,
attr->alt_port_num))
return -EINVAL;
/*
* Before passing a kernel QP to the HW, make sure that the
- * ownership bits of the send queue are set so that the
- * hardware doesn't start processing stale work requests.
+ * ownership bits of the send queue are set and the SQ
+ * headroom is stamped so that the hardware doesn't start
+ * processing stale work requests.
*/
if (!ibqp->uobject && cur_state == IB_QPS_RESET && new_state == IB_QPS_INIT) {
struct mlx4_wqe_ctrl_seg *ctrl;
int i;
- for (i = 0; i < qp->sq.max; ++i) {
+ for (i = 0; i < qp->sq.wqe_cnt; ++i) {
ctrl = get_send_wqe(qp, i);
ctrl->owner_opcode = cpu_to_be32(1 << 31);
+
+ stamp_send_wqe(qp, i);
}
}
*/
if (is_qp0(dev, qp)) {
if (cur_state != IB_QPS_RTR && new_state == IB_QPS_RTR)
- init_port(dev, qp->port);
+ if (mlx4_INIT_PORT(dev->dev, qp->port))
+ printk(KERN_WARNING "INIT_PORT failed for port %d\n",
+ qp->port);
if (cur_state != IB_QPS_RESET && cur_state != IB_QPS_ERR &&
(new_state == IB_QPS_RESET || new_state == IB_QPS_ERR))
if (!ib_modify_qp_is_ok(cur_state, new_state, ibqp->qp_type, attr_mask))
goto out;
- if ((attr_mask & IB_QP_PKEY_INDEX) &&
- attr->pkey_index >= dev->dev->caps.pkey_table_len) {
- goto out;
- }
-
if ((attr_mask & IB_QP_PORT) &&
(attr->port_num == 0 || attr->port_num > dev->dev->caps.num_ports)) {
goto out;
}
+ if (attr_mask & IB_QP_PKEY_INDEX) {
+ int p = attr_mask & IB_QP_PORT ? attr->port_num : qp->port;
+ if (attr->pkey_index >= dev->dev->caps.pkey_table_len[p])
+ goto out;
+ }
+
if (attr_mask & IB_QP_MAX_QP_RD_ATOMIC &&
attr->max_rd_atomic > dev->dev->caps.max_qp_init_rdma) {
goto out;
u16 pkey;
int send_size;
int header_size;
+ int spc;
int i;
send_size = 0;
printk("\n");
}
- inl->byte_count = cpu_to_be32(1 << 31 | header_size);
- memcpy(inl + 1, sqp->header_buf, header_size);
+ /*
+ * Inline data segments may not cross a 64 byte boundary. If
+ * our UD header is bigger than the space available up to the
+ * next 64 byte boundary in the WQE, use two inline data
+ * segments to hold the UD header.
+ */
+ spc = MLX4_INLINE_ALIGN -
+ ((unsigned long) (inl + 1) & (MLX4_INLINE_ALIGN - 1));
+ if (header_size <= spc) {
+ inl->byte_count = cpu_to_be32(1 << 31 | header_size);
+ memcpy(inl + 1, sqp->header_buf, header_size);
+ i = 1;
+ } else {
+ inl->byte_count = cpu_to_be32(1 << 31 | spc);
+ memcpy(inl + 1, sqp->header_buf, spc);
- return ALIGN(sizeof (struct mlx4_wqe_inline_seg) + header_size, 16);
+ inl = (void *) (inl + 1) + spc;
+ memcpy(inl + 1, sqp->header_buf + spc, header_size - spc);
+ /*
+ * Need a barrier here to make sure all the data is
+ * visible before the byte_count field is set.
+ * Otherwise the HCA prefetcher could grab the 64-byte
+ * chunk with this inline segment and get a valid (!=
+ * 0xffffffff) byte count but stale data, and end up
+ * generating a packet with bad headers.
+ *
+ * The first inline segment's byte_count field doesn't
+ * need a barrier, because it comes after a
+ * control/MLX segment and therefore is at an offset
+ * of 16 mod 64.
+ */
+ wmb();
+ inl->byte_count = cpu_to_be32(1 << 31 | (header_size - spc));
+ i = 2;
+ }
+
+ return ALIGN(i * sizeof (struct mlx4_wqe_inline_seg) + header_size, 16);
}
static int mlx4_wq_overflow(struct mlx4_ib_wq *wq, int nreq, struct ib_cq *ib_cq)
struct mlx4_ib_cq *cq;
cur = wq->head - wq->tail;
- if (likely(cur + nreq < wq->max))
+ if (likely(cur + nreq < wq->max_post))
return 0;
cq = to_mcq(ib_cq);
cur = wq->head - wq->tail;
spin_unlock(&cq->lock);
- return cur + nreq >= wq->max;
+ return cur + nreq >= wq->max_post;
}
int mlx4_ib_post_send(struct ib_qp *ibqp, struct ib_send_wr *wr,
goto out;
}
- ctrl = wqe = get_send_wqe(qp, ind & (qp->sq.max - 1));
- qp->sq.wrid[ind & (qp->sq.max - 1)] = wr->wr_id;
+ ctrl = wqe = get_send_wqe(qp, ind & (qp->sq.wqe_cnt - 1));
+ qp->sq.wrid[ind & (qp->sq.wqe_cnt - 1)] = wr->wr_id;
ctrl->srcrb_flags =
(wr->send_flags & IB_SEND_SIGNALED ?
}
ctrl->owner_opcode = mlx4_ib_opcode[wr->opcode] |
- (ind & qp->sq.max ? cpu_to_be32(1 << 31) : 0);
+ (ind & qp->sq.wqe_cnt ? cpu_to_be32(1 << 31) : 0);
+
+ /*
+ * We can improve latency by not stamping the last
+ * send queue WQE until after ringing the doorbell, so
+ * only stamp here if there are still more WQEs to post.
+ */
+ if (wr->next)
+ stamp_send_wqe(qp, (ind + qp->sq_spare_wqes) &
+ (qp->sq.wqe_cnt - 1));
++ind;
}
* and reach the HCA out of order.
*/
mmiowb();
+
+ stamp_send_wqe(qp, (ind + qp->sq_spare_wqes - 1) &
+ (qp->sq.wqe_cnt - 1));
}
spin_unlock_irqrestore(&qp->rq.lock, flags);
spin_lock_irqsave(&qp->rq.lock, flags);
- ind = qp->rq.head & (qp->rq.max - 1);
+ ind = qp->rq.head & (qp->rq.wqe_cnt - 1);
for (nreq = 0; wr; ++nreq, wr = wr->next) {
if (mlx4_wq_overflow(&qp->rq, nreq, qp->ibqp.send_cq)) {
qp->rq.wrid[ind] = wr->wr_id;
- ind = (ind + 1) & (qp->rq.max - 1);
+ ind = (ind + 1) & (qp->rq.wqe_cnt - 1);
}
out:
* Increment this value if any changes that break userspace ABI
* compatibility are made.
*/
-#define MLX4_IB_UVERBS_ABI_VERSION 2
+#define MLX4_IB_UVERBS_ABI_VERSION 3
/*
* Make sure that all structs defined in this file remain laid out so
struct mlx4_ib_create_qp {
__u64 buf_addr;
__u64 db_addr;
- __u8 log_sq_bb_count;
- __u8 log_sq_stride;
- __u8 reserved[6];
+ __u8 log_sq_bb_count;
+ __u8 log_sq_stride;
+ __u8 sq_no_prefetch;
+ __u8 reserved[5];
};
#endif /* MLX4_IB_USER_H */
#define IPOIB_CM_RX_DELAY (3 * 256 * HZ)
#define IPOIB_CM_RX_UPDATE_MASK (0x3)
-struct ipoib_cm_id {
- struct ib_cm_id *id;
- int flags;
- u32 remote_qpn;
- u32 remote_mtu;
-};
-
static struct ib_qp_attr ipoib_cm_err_attr = {
.qp_state = IB_QPS_ERR
};
return -ENOMEM;
p->dev = dev;
p->id = cm_id;
+ cm_id->context = p;
+ p->state = IPOIB_CM_RX_LIVE;
+ p->jiffies = jiffies;
+ INIT_LIST_HEAD(&p->list);
+
p->qp = ipoib_cm_create_rx_qp(dev, p);
if (IS_ERR(p->qp)) {
ret = PTR_ERR(p->qp);
if (ret)
goto err_modify;
+ spin_lock_irq(&priv->lock);
+ queue_delayed_work(ipoib_workqueue,
+ &priv->cm.stale_task, IPOIB_CM_RX_DELAY);
+ /* Add this entry to passive ids list head, but do not re-add it
+ * if IB_EVENT_QP_LAST_WQE_REACHED has moved it to flush list. */
+ p->jiffies = jiffies;
+ if (p->state == IPOIB_CM_RX_LIVE)
+ list_move(&p->list, &priv->cm.passive_ids);
+ spin_unlock_irq(&priv->lock);
+
ret = ipoib_cm_send_rep(dev, cm_id, p->qp, &event->param.req_rcvd, psn);
if (ret) {
ipoib_warn(priv, "failed to send REP: %d\n", ret);
- goto err_rep;
+ if (ib_modify_qp(p->qp, &ipoib_cm_err_attr, IB_QP_STATE))
+ ipoib_warn(priv, "unable to move qp to error state\n");
}
-
- cm_id->context = p;
- p->jiffies = jiffies;
- p->state = IPOIB_CM_RX_LIVE;
- spin_lock_irq(&priv->lock);
- if (list_empty(&priv->cm.passive_ids))
- queue_delayed_work(ipoib_workqueue,
- &priv->cm.stale_task, IPOIB_CM_RX_DELAY);
- list_add(&p->list, &priv->cm.passive_ids);
- spin_unlock_irq(&priv->lock);
return 0;
-err_rep:
err_modify:
ib_destroy_qp(p->qp);
err_qp:
p->mtu = be32_to_cpu(data->mtu);
- if (p->mtu < priv->dev->mtu + IPOIB_ENCAP_LEN) {
- ipoib_warn(priv, "Rejecting connection: mtu %d < device mtu %d + 4\n",
- p->mtu, priv->dev->mtu);
+ if (p->mtu <= IPOIB_ENCAP_LEN) {
+ ipoib_warn(priv, "Rejecting connection: mtu %d <= %d\n",
+ p->mtu, IPOIB_ENCAP_LEN);
return -EINVAL;
}
To compile this driver as a module, choose M here: the
module will be called amikbd.
+config ATARI_KBD_CORE
+ bool
+
config KEYBOARD_ATARI
tristate "Atari keyboard"
depends on ATARI
menuconfig MACINTOSH_DRIVERS
bool "Macintosh device drivers"
depends on PPC || MAC || X86
- default y
+ default y if (PPC_PMAC || MAC)
if MACINTOSH_DRIVERS
struct _MPT_SCSI_HOST *hd =
(struct _MPT_SCSI_HOST *)sdev->host->hostdata;
VirtTarget *vtarget = scsi_target(sdev)->hostdata;
- int ret = mptscsih_slave_configure(sdev);
+ int ret;
+
+ mptspi_initTarget(hd, vtarget, sdev);
+
+ ret = mptscsih_slave_configure(sdev);
if (ret)
return ret;
- mptspi_initTarget(hd, vtarget, sdev);
-
ddvprintk((MYIOC_s_INFO_FMT "id=%d min_period=0x%02x"
" max_offset=0x%02x max_width=%d\n", hd->ioc->name,
sdev->id, spi_min_period(scsi_target(sdev)),
struct resource *regs_claim;
struct sm501_platdata *platdata;
+ unsigned int in_suspend;
+ unsigned long pm_misc;
+
int unit_power[20];
unsigned int pdev_id;
unsigned int irq;
fmt_freq(decode_div(pll2, pm1, 8, 1<<12, 15, misc_div)),
fmt_freq(decode_div(pll2, pm1, 0, 1<<4, 15, misc_div)));
}
-#else
-static void sm501_dump_clk(struct sm501_devdata *sm)
+
+static void sm501_dump_regs(struct sm501_devdata *sm)
{
+ void __iomem *regs = sm->regs;
+
+ dev_info(sm->dev, "System Control %08x\n",
+ readl(regs + SM501_SYSTEM_CONTROL));
+ dev_info(sm->dev, "Misc Control %08x\n",
+ readl(regs + SM501_MISC_CONTROL));
+ dev_info(sm->dev, "GPIO Control Low %08x\n",
+ readl(regs + SM501_GPIO31_0_CONTROL));
+ dev_info(sm->dev, "GPIO Control Hi %08x\n",
+ readl(regs + SM501_GPIO63_32_CONTROL));
+ dev_info(sm->dev, "DRAM Control %08x\n",
+ readl(regs + SM501_DRAM_CONTROL));
+ dev_info(sm->dev, "Arbitration Ctrl %08x\n",
+ readl(regs + SM501_ARBTRTN_CONTROL));
+ dev_info(sm->dev, "Misc Timing %08x\n",
+ readl(regs + SM501_MISC_TIMING));
}
+
+static void sm501_dump_gate(struct sm501_devdata *sm)
+{
+ dev_info(sm->dev, "CurrentGate %08x\n",
+ readl(sm->regs + SM501_CURRENT_GATE));
+ dev_info(sm->dev, "CurrentClock %08x\n",
+ readl(sm->regs + SM501_CURRENT_CLOCK));
+ dev_info(sm->dev, "PowerModeControl %08x\n",
+ readl(sm->regs + SM501_POWER_MODE_CONTROL));
+}
+
+#else
+static inline void sm501_dump_gate(struct sm501_devdata *sm) { }
+static inline void sm501_dump_regs(struct sm501_devdata *sm) { }
+static inline void sm501_dump_clk(struct sm501_devdata *sm) { }
#endif
/* sm501_sync_regs
readl(sm->regs);
}
+static inline void sm501_mdelay(struct sm501_devdata *sm, unsigned int delay)
+{
+ /* during suspend/resume, we are currently not allowed to sleep,
+ * so change to using mdelay() instead of msleep() if we
+ * are in one of these paths */
+
+ if (sm->in_suspend)
+ mdelay(delay);
+ else
+ msleep(delay);
+}
+
/* sm501_misc_control
*
- * alters the misceleneous control parameters
+ * alters the miscellaneous control parameters
*/
int sm501_misc_control(struct device *dev,
dev_dbg(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n",
gate, clock, mode);
- msleep(16);
+ sm501_mdelay(sm, 16);
already:
mutex_unlock(&sm->clock_lock);
dev_info(sm->dev, "gate %08lx, clock %08lx, mode %08lx\n",
gate, clock, mode);
- msleep(16);
+ sm501_mdelay(sm, 16);
mutex_unlock(&sm->clock_lock);
sm501_dump_clk(sm);
/* sm501_init_reg
*
* Helper function for the init code to setup a register
+ *
+ * clear the bits which are set in r->mask, and then set
+ * the bits set in r->set.
*/
static inline void sm501_init_reg(struct sm501_devdata *sm,
unsigned long tmp;
tmp = readl(sm->regs + reg);
- tmp |= r->set;
tmp &= ~r->mask;
+ tmp |= r->set;
writel(tmp, sm->regs + reg);
}
sm501_init_reg(sm, SM501_GPIO31_0_CONTROL, &init->gpio_low);
sm501_init_reg(sm, SM501_GPIO63_32_CONTROL, &init->gpio_high);
+ if (init->m1xclk) {
+ dev_info(sm->dev, "setting M1XCLK to %ld\n", init->m1xclk);
+ sm501_set_clock(sm->dev, SM501_CLOCK_M1XCLK, init->m1xclk);
+ }
+
if (init->mclk) {
dev_info(sm->dev, "setting MCLK to %ld\n", init->mclk);
sm501_set_clock(sm->dev, SM501_CLOCK_MCLK, init->mclk);
}
- if (init->m1xclk) {
- dev_info(sm->dev, "setting M1XCLK to %ld\n", init->m1xclk);
- sm501_set_clock(sm->dev, SM501_CLOCK_M1XCLK, init->m1xclk);
- }
+}
+
+/* Check the PLL sources for the M1CLK and M1XCLK
+ *
+ * If the M1CLK and M1XCLKs are not sourced from the same PLL, then
+ * there is a risk (see errata AB-5) that the SM501 will cease proper
+ * function. If this happens, then it is likely the SM501 will
+ * hang the system.
+*/
+
+static int sm501_check_clocks(struct sm501_devdata *sm)
+{
+ unsigned long pwrmode = readl(sm->regs + SM501_CURRENT_CLOCK);
+ unsigned long msrc = (pwrmode & SM501_POWERMODE_M_SRC);
+ unsigned long m1src = (pwrmode & SM501_POWERMODE_M1_SRC);
+
+ return ((msrc == 0 && m1src != 0) || (msrc != 0 && m1src == 0));
}
static unsigned int sm501_mem_local[] = {
{
resource_size_t mem_avail;
unsigned long dramctrl;
+ unsigned long devid;
int ret;
mutex_init(&sm->clock_lock);
INIT_LIST_HEAD(&sm->devices);
- dramctrl = readl(sm->regs + SM501_DRAM_CONTROL);
+ devid = readl(sm->regs + SM501_DEVICEID);
+
+ if ((devid & SM501_DEVICEID_IDMASK) != SM501_DEVICEID_SM501) {
+ dev_err(sm->dev, "incorrect device id %08lx\n", devid);
+ return -EINVAL;
+ }
+ dramctrl = readl(sm->regs + SM501_DRAM_CONTROL);
mem_avail = sm501_mem_local[(dramctrl >> 13) & 0x7];
- dev_info(sm->dev, "SM501 At %p: Version %08x, %ld Mb, IRQ %d\n",
- sm->regs, readl(sm->regs + SM501_DEVICEID),
- (unsigned long)mem_avail >> 20, sm->irq);
+ dev_info(sm->dev, "SM501 At %p: Version %08lx, %ld Mb, IRQ %d\n",
+ sm->regs, devid, (unsigned long)mem_avail >> 20, sm->irq);
- dev_info(sm->dev, "CurrentGate %08x\n", readl(sm->regs+0x38));
- dev_info(sm->dev, "CurrentClock %08x\n", readl(sm->regs+0x3c));
- dev_info(sm->dev, "PowerModeControl %08x\n", readl(sm->regs+0x54));
+ sm501_dump_gate(sm);
ret = device_create_file(sm->dev, &dev_attr_dbg_regs);
if (ret)
}
}
+ ret = sm501_check_clocks(sm);
+ if (ret) {
+ dev_err(sm->dev, "M1X and M clocks sourced from different "
+ "PLLs\n");
+ return -EINVAL;
+ }
+
/* always create a framebuffer */
sm501_register_display(sm, &mem_avail);
}
+#ifdef CONFIG_PM
+/* power management support */
+
+static int sm501_plat_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct sm501_devdata *sm = platform_get_drvdata(pdev);
+
+ sm->in_suspend = 1;
+ sm->pm_misc = readl(sm->regs + SM501_MISC_CONTROL);
+
+ sm501_dump_regs(sm);
+ return 0;
+}
+
+static int sm501_plat_resume(struct platform_device *pdev)
+{
+ struct sm501_devdata *sm = platform_get_drvdata(pdev);
+
+ sm501_dump_regs(sm);
+ sm501_dump_gate(sm);
+ sm501_dump_clk(sm);
+
+ /* check to see if we are in the same state as when suspended */
+
+ if (readl(sm->regs + SM501_MISC_CONTROL) != sm->pm_misc) {
+ dev_info(sm->dev, "SM501_MISC_CONTROL changed over sleep\n");
+ writel(sm->pm_misc, sm->regs + SM501_MISC_CONTROL);
+
+ /* our suspend causes the controller state to change,
+ * either by something attempting setup, power loss,
+ * or an external reset event on power change */
+
+ if (sm->platdata && sm->platdata->init) {
+ sm501_init_regs(sm, sm->platdata->init);
+ }
+ }
+
+ /* dump our state from resume */
+
+ sm501_dump_regs(sm);
+ sm501_dump_clk(sm);
+
+ sm->in_suspend = 0;
+
+ return 0;
+}
+#else
+#define sm501_plat_suspend NULL
+#define sm501_plat_resume NULL
+#endif
+
/* Initialisation data for PCI devices */
static struct sm501_initdata sm501_pci_initdata = {
},
.devices = SM501_USE_ALL,
- .mclk = 100 * MHZ,
- .m1xclk = 160 * MHZ,
+
+ /* Errata AB-3 says that 72MHz is the fastest available
+ * for 33MHZ PCI with proper bus-mastering operation */
+
+ .mclk = 72 * MHZ,
+ .m1xclk = 144 * MHZ,
};
static struct sm501_platdata_fbsub sm501_pdata_fbsub = {
},
.probe = sm501_plat_probe,
.remove = sm501_plat_remove,
+ .suspend = sm501_plat_suspend,
+ .resume = sm501_plat_resume,
};
static int __init sm501_base_init(void)
}
/*
- * set link state for bonding master: if we have an active partnered
+ * set link state for bonding master: if we have an active
* aggregator, we're up, if not, we're down. Presumes that we cannot
* have an active aggregator if there are no slaves with link up.
*
+ * This behavior complies with IEEE 802.3 section 43.3.9.
+ *
* Called by bond_set_carrier(). Return zero if carrier state does not
* change, nonzero if it does.
*/
int bond_3ad_set_carrier(struct bonding *bond)
{
- struct aggregator *agg;
-
- agg = __get_active_agg(&(SLAVE_AD_INFO(bond->first_slave).aggregator));
- if (agg && MAC_ADDRESS_COMPARE(&agg->partner_system, &null_mac_addr)) {
+ if (__get_active_agg(&(SLAVE_AD_INFO(bond->first_slave).aggregator))) {
if (!netif_carrier_ok(bond->dev)) {
netif_carrier_on(bond->dev);
return 1;
bond_mc_list_destroy(bond);
/* Release the bonded slaves */
bond_release_all(bond_dev);
- unregister_netdevice(bond_dev);
bond_deinit(bond_dev);
+ unregister_netdevice(bond_dev);
}
#ifdef CONFIG_PROC_FS
printk(KERN_INFO DRV_NAME
": %s is being deleted...\n",
bond->dev->name);
- unregister_netdevice(bond->dev);
bond_deinit(bond->dev);
bond_destroy_sysfs_entry(bond);
+ unregister_netdevice(bond->dev);
rtnl_unlock();
goto out;
}
#include "bond_3ad.h"
#include "bond_alb.h"
-#define DRV_VERSION "3.1.2"
-#define DRV_RELDATE "January 20, 2007"
+#define DRV_VERSION "3.1.3"
+#define DRV_RELDATE "June 13, 2007"
#define DRV_NAME "bonding"
#define DRV_DESCRIPTION "Ethernet Channel Bonding Driver"
unsigned int status;
status = t3_read_reg(phy->adapter,
- XGM_REG(A_XGM_SERDES_STAT0, phy->addr));
+ XGM_REG(A_XGM_SERDES_STAT0, phy->addr)) |
+ t3_read_reg(phy->adapter,
+ XGM_REG(A_XGM_SERDES_STAT1, phy->addr)) |
+ t3_read_reg(phy->adapter,
+ XGM_REG(A_XGM_SERDES_STAT2, phy->addr)) |
+ t3_read_reg(phy->adapter,
+ XGM_REG(A_XGM_SERDES_STAT3, phy->addr));
*link_ok = !(status & F_LOWSIG0);
}
if (speed)
void t3_xaui_direct_phy_prep(struct cphy *phy, struct adapter *adapter,
int phy_addr, const struct mdio_ops *mdio_ops)
{
- cphy_init(phy, adapter, 1, &xaui_direct_ops, mdio_ops);
+ cphy_init(phy, adapter, phy_addr, &xaui_direct_ops, mdio_ops);
}
static void cxgb_netpoll(struct net_device *dev)
{
struct adapter *adapter = dev->priv;
- struct sge_qset *qs = dev2qset(dev);
+ struct port_info *pi = netdev_priv(dev);
+ int qidx;
- t3_intr_handler(adapter, qs->rspq.polling) (adapter->pdev->irq,
- adapter);
+ for (qidx = pi->first_qset; qidx < pi->first_qset + pi->nqsets; qidx++) {
+ struct sge_qset *qs = &adapter->sge.qs[qidx];
+ void *source;
+
+ if (adapter->flags & USING_MSIX)
+ source = qs;
+ else
+ source = adapter;
+
+ t3_intr_handler(adapter, qs->rspq.polling) (0, source);
+ }
}
#endif
#define V_COPYALLFRAMES(x) ((x) << S_COPYALLFRAMES)
#define F_COPYALLFRAMES V_COPYALLFRAMES(1U)
+#define S_DISBCAST 1
+#define V_DISBCAST(x) ((x) << S_DISBCAST)
+#define F_DISBCAST V_DISBCAST(1U)
+
#define A_XGM_RX_HASH_LOW 0x814
#define A_XGM_RX_HASH_HIGH 0x818
#define F_RESETPLL01 V_RESETPLL01(1U)
#define A_XGM_SERDES_STAT0 0x8f0
+#define A_XGM_SERDES_STAT1 0x8f4
+#define A_XGM_SERDES_STAT2 0x8f8
#define S_LOWSIG0 0
#define V_LOWSIG0(x) ((x) << S_LOWSIG0)
struct port_info *pi;
skb_pull(skb, sizeof(*p) + pad);
- skb->dev->last_rx = jiffies;
skb->protocol = eth_type_trans(skb, adap->port[p->iff]);
+ skb->dev->last_rx = jiffies;
pi = netdev_priv(skb->dev);
if (pi->rx_csum_offload && p->csum_valid && p->csum == 0xffff &&
!p->fragment) {
struct sge_rspq *q = &qs->rspq;
spin_lock(&q->lock);
- BUG_ON(napi_is_scheduled(qs->netdev));
if (handle_responses(adap, q) < 0)
q->unhandled_irqs++;
return 0;
}
+static void disable_exact_filters(struct cmac *mac)
+{
+ unsigned int i, reg = mac->offset + A_XGM_RX_EXACT_MATCH_LOW_1;
+
+ for (i = 0; i < EXACT_ADDR_FILTERS; i++, reg += 8) {
+ u32 v = t3_read_reg(mac->adapter, reg);
+ t3_write_reg(mac->adapter, reg, v);
+ }
+ t3_read_reg(mac->adapter, A_XGM_RX_EXACT_MATCH_LOW_1); /* flush */
+}
+
+static void enable_exact_filters(struct cmac *mac)
+{
+ unsigned int i, reg = mac->offset + A_XGM_RX_EXACT_MATCH_HIGH_1;
+
+ for (i = 0; i < EXACT_ADDR_FILTERS; i++, reg += 8) {
+ u32 v = t3_read_reg(mac->adapter, reg);
+ t3_write_reg(mac->adapter, reg, v);
+ }
+ t3_read_reg(mac->adapter, A_XGM_RX_EXACT_MATCH_LOW_1); /* flush */
+}
+
/* Calculate the RX hash filter index of an Ethernet address */
static int hash_hw_addr(const u8 * addr)
{
return 0;
}
+static int rx_fifo_hwm(int mtu)
+{
+ int hwm;
+
+ hwm = max(MAC_RXFIFO_SIZE - 3 * mtu, (MAC_RXFIFO_SIZE * 38) / 100);
+ return min(hwm, MAC_RXFIFO_SIZE - 8192);
+}
+
int t3_mac_set_mtu(struct cmac *mac, unsigned int mtu)
{
int hwm, lwm;
lwm = min(3 * (int)mtu, MAC_RXFIFO_SIZE / 4);
v = t3_read_reg(adap, A_XGM_RXFIFO_CFG + mac->offset);
+ if (adap->params.rev == T3_REV_B2 &&
+ (t3_read_reg(adap, A_XGM_RX_CTRL + mac->offset) & F_RXEN)) {
+ disable_exact_filters(mac);
+ t3_set_reg_field(adap, A_XGM_RXFIFO_CFG + mac->offset,
+ F_ENHASHMCAST | F_COPYALLFRAMES, F_DISBCAST);
+
+ /* drain rx FIFO */
+ if (t3_wait_op_done(adap,
+ A_XGM_RX_MAX_PKT_SIZE_ERR_CNT +
+ mac->offset,
+ 1 << 31, 1, 20, 5)) {
+ t3_write_reg(adap, A_XGM_RXFIFO_CFG + mac->offset, v);
+ enable_exact_filters(mac);
+ return -EIO;
+ }
+ t3_write_reg(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, mtu);
+ enable_exact_filters(mac);
+ } else
+ t3_write_reg(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, mtu);
+
+ /*
+ * Adjust the PAUSE frame watermarks. We always set the LWM, and the
+ * HWM only if flow-control is enabled.
+ */
+ hwm = rx_fifo_hwm(mtu);
+ lwm = min(3 * (int)mtu, MAC_RXFIFO_SIZE / 4);
v &= ~V_RXFIFOPAUSELWM(M_RXFIFOPAUSELWM);
v |= V_RXFIFOPAUSELWM(lwm / 8);
if (G_RXFIFOPAUSEHWM(v))
v = (v & ~V_RXFIFOPAUSEHWM(M_RXFIFOPAUSEHWM)) |
V_RXFIFOPAUSEHWM(hwm / 8);
+
t3_write_reg(adap, A_XGM_RXFIFO_CFG + mac->offset, v);
/* Adjust the TX FIFO threshold based on the MTU */
(hwm - lwm) * 4 / 8);
t3_write_reg(adap, A_XGM_TX_PAUSE_QUANTA + mac->offset,
MAC_RXFIFO_SIZE * 4 * 8 / 512);
-
return 0;
}
V_PORTSPEED(M_PORTSPEED), val);
}
+ val = t3_read_reg(adap, A_XGM_RXFIFO_CFG + oft);
+ val &= ~V_RXFIFOPAUSEHWM(M_RXFIFOPAUSEHWM);
+ if (fc & PAUSE_TX)
+ val |= V_RXFIFOPAUSEHWM(rx_fifo_hwm(
+ t3_read_reg(adap,
+ A_XGM_RX_MAX_PKT_SIZE
+ + oft)) / 8);
+ t3_write_reg(adap, A_XGM_RXFIFO_CFG + oft, val);
+
t3_set_reg_field(adap, A_XGM_TX_CFG + oft, F_TXPAUSEEN,
(fc & PAUSE_RX) ? F_TXPAUSEEN : 0);
return 0;
unsigned int rx_xcnt;
int status;
+ status = 0;
+ tx_xcnt = 1; /* By default tx_xcnt is making progress */
+ tx_tcnt = mac->tx_tcnt; /* If tx_mcnt is progressing ignore tx_tcnt */
+ rx_xcnt = 1; /* By default rx_xcnt is making progress */
if (tx_mcnt == mac->tx_mcnt) {
tx_xcnt = (G_TXSPI4SOPCNT(t3_read_reg(adap,
A_XGM_TX_SPI4_SOP_EOP_CNT +
tx_tcnt = (G_TXDROPCNTCH0RCVD(t3_read_reg(adap,
A_TP_PIO_DATA)));
} else {
- mac->toggle_cnt = 0;
- return 0;
+ goto rxcheck;
}
} else {
mac->toggle_cnt = 0;
- return 0;
+ goto rxcheck;
}
if (((tx_tcnt != mac->tx_tcnt) &&
(tx_xcnt == 0) && (mac->tx_xcnt == 0)) ||
((mac->tx_mcnt == tx_mcnt) &&
(tx_xcnt != 0) && (mac->tx_xcnt != 0))) {
- if (mac->toggle_cnt > 4)
+ if (mac->toggle_cnt > 4) {
status = 2;
- else
+ goto out;
+ } else {
status = 1;
+ goto out;
+ }
} else {
mac->toggle_cnt = 0;
- return 0;
+ goto rxcheck;
}
+rxcheck:
if (rx_mcnt != mac->rx_mcnt)
rx_xcnt = (G_TXSPI4SOPCNT(t3_read_reg(adap,
A_XGM_RX_SPI4_SOP_EOP_CNT +
mac->offset)));
- else
- return 0;
+ else
+ goto out;
- if (mac->rx_mcnt != s->rx_frames && rx_xcnt == 0 && mac->rx_xcnt == 0)
+ if (mac->rx_mcnt != s->rx_frames && rx_xcnt == 0 &&
+ mac->rx_xcnt == 0) {
status = 2;
-
+ goto out;
+ }
+
+out:
mac->tx_tcnt = tx_tcnt;
mac->tx_xcnt = tx_xcnt;
mac->tx_mcnt = s->tx_frames;
drain_ring(dev);
- if (np->wolenabled)
+ if (np->wolenabled) {
+ writel(NVREG_PFF_ALWAYS|NVREG_PFF_MYADDR, base + NvRegPacketFilterFlags);
nv_start_rx(dev);
+ }
/* FIXME: power down nic */
* TODO: probe for these or load them from PARAM
*/
netdev->base_addr = 0x4200;
- netdev->irq = MIPSCPU_INT_BASE + MIPSCPU_INT_MB0 +
+ netdev->irq = MIPS_CPU_IRQ_BASE + MIPSCPU_INT_MB0 +
inl(mipsnet_reg_address(netdev, interruptInfo));
// Get the io region now, get irq on open()
#include "icm.h"
enum {
- MLX4_COMMAND_INTERFACE_REV = 1
+ MLX4_COMMAND_INTERFACE_MIN_REV = 2,
+ MLX4_COMMAND_INTERFACE_MAX_REV = 3,
+ MLX4_COMMAND_INTERFACE_NEW_PORT_CMDS = 3,
};
extern void __buggy_use_of_MLX4_GET(void);
u16 size;
u16 stat_rate;
int err;
+ int i;
#define QUERY_DEV_CAP_OUT_SIZE 0x100
#define QUERY_DEV_CAP_MAX_SRQ_SZ_OFFSET 0x10
err = mlx4_cmd_box(dev, 0, mailbox->dma, 0, 0, MLX4_CMD_QUERY_DEV_CAP,
MLX4_CMD_TIME_CLASS_A);
-
if (err)
goto out;
dev_cap->max_rdma_global = 1 << (field & 0x3f);
MLX4_GET(field, outbox, QUERY_DEV_CAP_ACK_DELAY_OFFSET);
dev_cap->local_ca_ack_delay = field & 0x1f;
- MLX4_GET(field, outbox, QUERY_DEV_CAP_MTU_WIDTH_OFFSET);
- dev_cap->max_mtu = field >> 4;
- dev_cap->max_port_width = field & 0xf;
MLX4_GET(field, outbox, QUERY_DEV_CAP_VL_PORT_OFFSET);
- dev_cap->max_vl = field >> 4;
dev_cap->num_ports = field & 0xf;
- MLX4_GET(field, outbox, QUERY_DEV_CAP_MAX_GID_OFFSET);
- dev_cap->max_gids = 1 << (field & 0xf);
MLX4_GET(stat_rate, outbox, QUERY_DEV_CAP_RATE_SUPPORT_OFFSET);
dev_cap->stat_rate_support = stat_rate;
- MLX4_GET(field, outbox, QUERY_DEV_CAP_MAX_PKEY_OFFSET);
- dev_cap->max_pkeys = 1 << (field & 0xf);
MLX4_GET(dev_cap->flags, outbox, QUERY_DEV_CAP_FLAGS_OFFSET);
MLX4_GET(field, outbox, QUERY_DEV_CAP_RSVD_UAR_OFFSET);
dev_cap->reserved_uars = field >> 4;
MLX4_GET(dev_cap->max_icm_sz, outbox,
QUERY_DEV_CAP_MAX_ICM_SZ_OFFSET);
+ if (dev->flags & MLX4_FLAG_OLD_PORT_CMDS) {
+ for (i = 1; i <= dev_cap->num_ports; ++i) {
+ MLX4_GET(field, outbox, QUERY_DEV_CAP_VL_PORT_OFFSET);
+ dev_cap->max_vl[i] = field >> 4;
+ MLX4_GET(field, outbox, QUERY_DEV_CAP_MTU_WIDTH_OFFSET);
+ dev_cap->max_mtu[i] = field >> 4;
+ dev_cap->max_port_width[i] = field & 0xf;
+ MLX4_GET(field, outbox, QUERY_DEV_CAP_MAX_GID_OFFSET);
+ dev_cap->max_gids[i] = 1 << (field & 0xf);
+ MLX4_GET(field, outbox, QUERY_DEV_CAP_MAX_PKEY_OFFSET);
+ dev_cap->max_pkeys[i] = 1 << (field & 0xf);
+ }
+ } else {
+#define QUERY_PORT_MTU_OFFSET 0x01
+#define QUERY_PORT_WIDTH_OFFSET 0x06
+#define QUERY_PORT_MAX_GID_PKEY_OFFSET 0x07
+#define QUERY_PORT_MAX_VL_OFFSET 0x0b
+
+ for (i = 1; i <= dev_cap->num_ports; ++i) {
+ err = mlx4_cmd_box(dev, 0, mailbox->dma, i, 0, MLX4_CMD_QUERY_PORT,
+ MLX4_CMD_TIME_CLASS_B);
+ if (err)
+ goto out;
+
+ MLX4_GET(field, outbox, QUERY_PORT_MTU_OFFSET);
+ dev_cap->max_mtu[i] = field & 0xf;
+ MLX4_GET(field, outbox, QUERY_PORT_WIDTH_OFFSET);
+ dev_cap->max_port_width[i] = field & 0xf;
+ MLX4_GET(field, outbox, QUERY_PORT_MAX_GID_PKEY_OFFSET);
+ dev_cap->max_gids[i] = 1 << (field >> 4);
+ dev_cap->max_pkeys[i] = 1 << (field & 0xf);
+ MLX4_GET(field, outbox, QUERY_PORT_MAX_VL_OFFSET);
+ dev_cap->max_vl[i] = field & 0xf;
+ }
+ }
+
if (dev_cap->bmme_flags & 1)
mlx4_dbg(dev, "Base MM extensions: yes "
"(flags %d, rsvd L_Key %08x)\n",
mlx4_dbg(dev, "Max CQEs: %d, max WQEs: %d, max SRQ WQEs: %d\n",
dev_cap->max_cq_sz, dev_cap->max_qp_sz, dev_cap->max_srq_sz);
mlx4_dbg(dev, "Local CA ACK delay: %d, max MTU: %d, port width cap: %d\n",
- dev_cap->local_ca_ack_delay, 128 << dev_cap->max_mtu,
- dev_cap->max_port_width);
+ dev_cap->local_ca_ack_delay, 128 << dev_cap->max_mtu[1],
+ dev_cap->max_port_width[1]);
mlx4_dbg(dev, "Max SQ desc size: %d, max SQ S/G: %d\n",
dev_cap->max_sq_desc_sz, dev_cap->max_sq_sg);
mlx4_dbg(dev, "Max RQ desc size: %d, max RQ S/G: %d\n",
((fw_ver & 0x0000ffffull) << 16);
MLX4_GET(cmd_if_rev, outbox, QUERY_FW_CMD_IF_REV_OFFSET);
- if (cmd_if_rev != MLX4_COMMAND_INTERFACE_REV) {
+ if (cmd_if_rev < MLX4_COMMAND_INTERFACE_MIN_REV ||
+ cmd_if_rev > MLX4_COMMAND_INTERFACE_MAX_REV) {
mlx4_err(dev, "Installed FW has unsupported "
"command interface revision %d.\n",
cmd_if_rev);
(int) (dev->caps.fw_ver >> 32),
(int) (dev->caps.fw_ver >> 16) & 0xffff,
(int) dev->caps.fw_ver & 0xffff);
- mlx4_err(dev, "This driver version supports only revision %d.\n",
- MLX4_COMMAND_INTERFACE_REV);
+ mlx4_err(dev, "This driver version supports only revisions %d to %d.\n",
+ MLX4_COMMAND_INTERFACE_MIN_REV, MLX4_COMMAND_INTERFACE_MAX_REV);
err = -ENODEV;
goto out;
}
+ if (cmd_if_rev < MLX4_COMMAND_INTERFACE_NEW_PORT_CMDS)
+ dev->flags |= MLX4_FLAG_OLD_PORT_CMDS;
+
MLX4_GET(lg, outbox, QUERY_FW_MAX_CMD_OFFSET);
cmd->max_cmds = 1 << lg;
return err;
}
-int mlx4_INIT_PORT(struct mlx4_dev *dev, struct mlx4_init_port_param *param, int port)
+int mlx4_INIT_PORT(struct mlx4_dev *dev, int port)
{
struct mlx4_cmd_mailbox *mailbox;
u32 *inbox;
int err;
u32 flags;
+ u16 field;
+ if (dev->flags & MLX4_FLAG_OLD_PORT_CMDS) {
#define INIT_PORT_IN_SIZE 256
#define INIT_PORT_FLAGS_OFFSET 0x00
#define INIT_PORT_FLAG_SIG (1 << 18)
#define INIT_PORT_NODE_GUID_OFFSET 0x18
#define INIT_PORT_SI_GUID_OFFSET 0x20
- mailbox = mlx4_alloc_cmd_mailbox(dev);
- if (IS_ERR(mailbox))
- return PTR_ERR(mailbox);
- inbox = mailbox->buf;
+ mailbox = mlx4_alloc_cmd_mailbox(dev);
+ if (IS_ERR(mailbox))
+ return PTR_ERR(mailbox);
+ inbox = mailbox->buf;
- memset(inbox, 0, INIT_PORT_IN_SIZE);
+ memset(inbox, 0, INIT_PORT_IN_SIZE);
- flags = 0;
- flags |= param->set_guid0 ? INIT_PORT_FLAG_G0 : 0;
- flags |= param->set_node_guid ? INIT_PORT_FLAG_NG : 0;
- flags |= param->set_si_guid ? INIT_PORT_FLAG_SIG : 0;
- flags |= (param->vl_cap & 0xf) << INIT_PORT_VL_SHIFT;
- flags |= (param->port_width_cap & 0xf) << INIT_PORT_PORT_WIDTH_SHIFT;
- MLX4_PUT(inbox, flags, INIT_PORT_FLAGS_OFFSET);
+ flags = 0;
+ flags |= (dev->caps.vl_cap[port] & 0xf) << INIT_PORT_VL_SHIFT;
+ flags |= (dev->caps.port_width_cap[port] & 0xf) << INIT_PORT_PORT_WIDTH_SHIFT;
+ MLX4_PUT(inbox, flags, INIT_PORT_FLAGS_OFFSET);
- MLX4_PUT(inbox, param->mtu, INIT_PORT_MTU_OFFSET);
- MLX4_PUT(inbox, param->max_gid, INIT_PORT_MAX_GID_OFFSET);
- MLX4_PUT(inbox, param->max_pkey, INIT_PORT_MAX_PKEY_OFFSET);
- MLX4_PUT(inbox, param->guid0, INIT_PORT_GUID0_OFFSET);
- MLX4_PUT(inbox, param->node_guid, INIT_PORT_NODE_GUID_OFFSET);
- MLX4_PUT(inbox, param->si_guid, INIT_PORT_SI_GUID_OFFSET);
+ field = 128 << dev->caps.mtu_cap[port];
+ MLX4_PUT(inbox, field, INIT_PORT_MTU_OFFSET);
+ field = dev->caps.gid_table_len[port];
+ MLX4_PUT(inbox, field, INIT_PORT_MAX_GID_OFFSET);
+ field = dev->caps.pkey_table_len[port];
+ MLX4_PUT(inbox, field, INIT_PORT_MAX_PKEY_OFFSET);
- err = mlx4_cmd(dev, mailbox->dma, port, 0, MLX4_CMD_INIT_PORT,
- MLX4_CMD_TIME_CLASS_A);
+ err = mlx4_cmd(dev, mailbox->dma, port, 0, MLX4_CMD_INIT_PORT,
+ MLX4_CMD_TIME_CLASS_A);
- mlx4_free_cmd_mailbox(dev, mailbox);
+ mlx4_free_cmd_mailbox(dev, mailbox);
+ } else
+ err = mlx4_cmd(dev, 0, port, 0, MLX4_CMD_INIT_PORT,
+ MLX4_CMD_TIME_CLASS_A);
return err;
}
int max_responder_per_qp;
int max_rdma_global;
int local_ca_ack_delay;
- int max_mtu;
- int max_port_width;
- int max_vl;
int num_ports;
- int max_gids;
+ int max_mtu[MLX4_MAX_PORTS + 1];
+ int max_port_width[MLX4_MAX_PORTS + 1];
+ int max_vl[MLX4_MAX_PORTS + 1];
+ int max_gids[MLX4_MAX_PORTS + 1];
+ int max_pkeys[MLX4_MAX_PORTS + 1];
u16 stat_rate_support;
- int max_pkeys;
u32 flags;
int reserved_uars;
int uar_size;
static int __devinit mlx4_dev_cap(struct mlx4_dev *dev, struct mlx4_dev_cap *dev_cap)
{
int err;
+ int i;
err = mlx4_QUERY_DEV_CAP(dev, dev_cap);
if (err) {
}
dev->caps.num_ports = dev_cap->num_ports;
+ for (i = 1; i <= dev->caps.num_ports; ++i) {
+ dev->caps.vl_cap[i] = dev_cap->max_vl[i];
+ dev->caps.mtu_cap[i] = dev_cap->max_mtu[i];
+ dev->caps.gid_table_len[i] = dev_cap->max_gids[i];
+ dev->caps.pkey_table_len[i] = dev_cap->max_pkeys[i];
+ dev->caps.port_width_cap[i] = dev_cap->max_port_width[i];
+ }
+
dev->caps.num_uars = dev_cap->uar_size / PAGE_SIZE;
- dev->caps.vl_cap = dev_cap->max_vl;
- dev->caps.mtu_cap = dev_cap->max_mtu;
- dev->caps.gid_table_len = dev_cap->max_gids;
- dev->caps.pkey_table_len = dev_cap->max_pkeys;
dev->caps.local_ca_ack_delay = dev_cap->local_ca_ack_delay;
dev->caps.bf_reg_size = dev_cap->bf_reg_size;
dev->caps.bf_regs_per_page = dev_cap->bf_regs_per_page;
dev->caps.reserved_mrws = dev_cap->reserved_mrws;
dev->caps.reserved_uars = dev_cap->reserved_uars;
dev->caps.reserved_pds = dev_cap->reserved_pds;
- dev->caps.port_width_cap = dev_cap->max_port_width;
dev->caps.mtt_entry_sz = MLX4_MTT_ENTRY_PER_SEG * dev_cap->mtt_entry_sz;
dev->caps.page_size_cap = ~(u32) (dev_cap->min_page_sz - 1);
dev->caps.flags = dev_cap->flags;
{
struct netdev_private *np = netdev_priv(to_net_dev(dev));
int new_setting;
- u32 flags;
+ unsigned long flags;
/* Find out the new setting */
if (!strncmp("on", buf, count - 1) || !strncmp("1", buf, count - 1))
goto err;
if (proto == PPP_COMP) {
- ns = dev_alloc_skb(ppp->mru + PPP_HDRLEN);
+ int obuff_size;
+
+ switch(ppp->rcomp->compress_proto) {
+ case CI_MPPE:
+ obuff_size = ppp->mru + PPP_HDRLEN + 1;
+ break;
+ default:
+ obuff_size = ppp->mru + PPP_HDRLEN;
+ break;
+ }
+
+ ns = dev_alloc_skb(obuff_size);
if (ns == 0) {
printk(KERN_ERR "ppp_decompress_frame: no memory\n");
goto err;
/*
* Make sure we have enough room to decrypt the packet.
- * To account for possible PFC we should only subtract 1
- * byte whereas in mppe_compress() we added 2 bytes (+MPPE_OVHD);
- * However, we assume no PFC, thus subtracting 2 bytes.
+ * Note that for our test we only subtract 1 byte whereas in
+ * mppe_compress() we added 2 bytes (+MPPE_OVHD);
+ * this is to account for possible PFC.
*/
- if (osize < isize - MPPE_OVHD - 2) {
+ if (osize < isize - MPPE_OVHD - 1) {
printk(KERN_DEBUG "mppe_decompress[%d]: osize too small! "
"(have: %d need: %d)\n", state->unit,
- osize, isize - MPPE_OVHD - 2);
+ osize, isize - MPPE_OVHD - 1);
return DECOMP_ERROR;
}
osize = isize - MPPE_OVHD - 2; /* assume no PFC */
hwdescr->dmac_cmd_status = SPIDER_NET_DESCR_NOT_IN_USE;
} else {
hwdescr->buf_addr = buf;
- hwdescr->next_descr_addr = 0;
wmb();
hwdescr->dmac_cmd_status = SPIDER_NET_DESCR_CARDOWNED |
SPIDER_NET_DMAC_NOINTR_COMPLETE;
-
- wmb();
- descr->prev->hwdescr->next_descr_addr = descr->bus_addr;
}
return 0;
static int
spider_net_alloc_rx_skbs(struct spider_net_card *card)
{
- int result;
- struct spider_net_descr_chain *chain;
+ struct spider_net_descr_chain *chain = &card->rx_chain;
+ struct spider_net_descr *start = chain->tail;
+ struct spider_net_descr *descr = start;
- result = -ENOMEM;
+ /* Link up the hardware chain pointers */
+ do {
+ descr->prev->hwdescr->next_descr_addr = descr->bus_addr;
+ descr = descr->next;
+ } while (descr != start);
- chain = &card->rx_chain;
/* Put at least one buffer into the chain. if this fails,
* we've got a problem. If not, spider_net_refill_rx_chain
* will do the rest at the end of this function. */
error:
spider_net_free_rx_chain_contents(card);
- return result;
+ return -ENOMEM;
}
/**
SPIDER_NET_DESCR_CARDOWNED | SPIDER_NET_DMAC_NOCS;
spin_unlock_irqrestore(&chain->lock, flags);
- if (skb->protocol == htons(ETH_P_IP) && skb->ip_summed == CHECKSUM_PARTIAL)
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
switch (ip_hdr(skb)->protocol) {
case IPPROTO_TCP:
hwdescr->dmac_cmd_status |= SPIDER_NET_DMAC_TCP;
}
#endif
+/**
+ * spider_net_resync_head_ptr - Advance head ptr past empty descrs
+ *
+ * If the driver fails to keep up and empty the queue, then the
+ * hardware wil run out of room to put incoming packets. This
+ * will cause the hardware to skip descrs that are full (instead
+ * of halting/retrying). Thus, once the driver runs, it wil need
+ * to "catch up" to where the hardware chain pointer is at.
+ */
+static void spider_net_resync_head_ptr(struct spider_net_card *card)
+{
+ unsigned long flags;
+ struct spider_net_descr_chain *chain = &card->rx_chain;
+ struct spider_net_descr *descr;
+ int i, status;
+
+ /* Advance head pointer past any empty descrs */
+ descr = chain->head;
+ status = spider_net_get_descr_status(descr->hwdescr);
+
+ if (status == SPIDER_NET_DESCR_NOT_IN_USE)
+ return;
+
+ spin_lock_irqsave(&chain->lock, flags);
+
+ descr = chain->head;
+ status = spider_net_get_descr_status(descr->hwdescr);
+ for (i=0; i<chain->num_desc; i++) {
+ if (status != SPIDER_NET_DESCR_CARDOWNED) break;
+ descr = descr->next;
+ status = spider_net_get_descr_status(descr->hwdescr);
+ }
+ chain->head = descr;
+
+ spin_unlock_irqrestore(&chain->lock, flags);
+}
+
+static int spider_net_resync_tail_ptr(struct spider_net_card *card)
+{
+ struct spider_net_descr_chain *chain = &card->rx_chain;
+ struct spider_net_descr *descr;
+ int i, status;
+
+ /* Advance tail pointer past any empty and reaped descrs */
+ descr = chain->tail;
+ status = spider_net_get_descr_status(descr->hwdescr);
+
+ for (i=0; i<chain->num_desc; i++) {
+ if ((status != SPIDER_NET_DESCR_CARDOWNED) &&
+ (status != SPIDER_NET_DESCR_NOT_IN_USE)) break;
+ descr = descr->next;
+ status = spider_net_get_descr_status(descr->hwdescr);
+ }
+ chain->tail = descr;
+
+ if ((i == chain->num_desc) || (i == 0))
+ return 1;
+ return 0;
+}
+
/**
* spider_net_decode_one_descr - processes an RX descriptor
* @card: card structure
goto bad_desc;
}
- if (hwdescr->dmac_cmd_status & 0xfefe) {
+ if (hwdescr->dmac_cmd_status & 0xfcf4) {
pr_err("%s: bad status, cmd_status=x%08x\n",
card->netdev->name,
hwdescr->dmac_cmd_status);
/* Ok, we've got a packet in descr */
spider_net_pass_skb_up(descr, card);
+ descr->skb = NULL;
hwdescr->dmac_cmd_status = SPIDER_NET_DESCR_NOT_IN_USE;
return 1;
}
}
+ if ((packets_done == 0) && (card->num_rx_ints != 0)) {
+ no_more_packets = spider_net_resync_tail_ptr(card);
+ spider_net_resync_head_ptr(card);
+ }
+ card->num_rx_ints = 0;
+
netdev->quota -= packets_done;
*budget -= packets_done;
spider_net_refill_rx_chain(card);
if (no_more_packets) {
netif_rx_complete(netdev);
spider_net_rx_irq_on(card);
+ card->ignore_rx_ramfull = 0;
return 0;
}
case SPIDER_NET_GRFBFLLINT: /* fallthrough */
case SPIDER_NET_GRFAFLLINT: /* fallthrough */
case SPIDER_NET_GRMFLLINT:
- if (netif_msg_intr(card) && net_ratelimit())
- pr_err("Spider RX RAM full, incoming packets "
- "might be discarded!\n");
- spider_net_rx_irq_off(card);
- netif_rx_schedule(card->netdev);
+ /* Could happen when rx chain is full */
+ if (card->ignore_rx_ramfull == 0) {
+ card->ignore_rx_ramfull = 1;
+ spider_net_resync_head_ptr(card);
+ spider_net_refill_rx_chain(card);
+ spider_net_enable_rxdmac(card);
+ card->num_rx_ints ++;
+ netif_rx_schedule(card->netdev);
+ }
show_error = 0;
break;
case SPIDER_NET_GDCDCEINT: /* fallthrough */
case SPIDER_NET_GDBDCEINT: /* fallthrough */
case SPIDER_NET_GDADCEINT:
- if (netif_msg_intr(card) && net_ratelimit())
- pr_err("got descriptor chain end interrupt, "
- "restarting DMAC %c.\n",
- 'D'-(i-SPIDER_NET_GDDDCEINT)/3);
+ spider_net_resync_head_ptr(card);
spider_net_refill_rx_chain(card);
spider_net_enable_rxdmac(card);
+ card->num_rx_ints ++;
+ netif_rx_schedule(card->netdev);
show_error = 0;
break;
case SPIDER_NET_GDCINVDINT: /* fallthrough */
case SPIDER_NET_GDBINVDINT: /* fallthrough */
case SPIDER_NET_GDAINVDINT:
- /* could happen when rx chain is full */
+ /* Could happen when rx chain is full */
+ spider_net_resync_head_ptr(card);
spider_net_refill_rx_chain(card);
spider_net_enable_rxdmac(card);
+ card->num_rx_ints ++;
+ netif_rx_schedule(card->netdev);
show_error = 0;
break;
if (status_reg & SPIDER_NET_RXINT ) {
spider_net_rx_irq_off(card);
netif_rx_schedule(netdev);
+ card->num_rx_ints ++;
}
if (status_reg & SPIDER_NET_TXINT)
netif_rx_schedule(netdev);
spider_net_setup_netdev_ops(netdev);
- netdev->features = NETIF_F_HW_CSUM | NETIF_F_LLTX;
+ netdev->features = NETIF_F_IP_CSUM | NETIF_F_LLTX;
/* some time: NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX |
* NETIF_F_HW_VLAN_FILTER */
netdev->irq = card->pdev->irq;
+ card->num_rx_ints = 0;
+ card->ignore_rx_ramfull = 0;
dn = pci_device_to_OF_node(card->pdev);
if (!dn)
#ifndef _SPIDER_NET_H
#define _SPIDER_NET_H
-#define VERSION "2.0 A"
+#define VERSION "2.0 B"
#include "sungem_phy.h"
#define SPIDER_NET_GDTBSTA 0x00000300
#define SPIDER_NET_GDTDCEIDIS 0x00000002
#define SPIDER_NET_DMA_TX_VALUE SPIDER_NET_TX_DMA_EN | \
+ SPIDER_NET_GDTDCEIDIS | \
SPIDER_NET_GDTBSTA
#define SPIDER_NET_DMA_TX_FEND_VALUE 0x00030003
SPIDER_NET_GRISPDNGINT
};
-#define SPIDER_NET_TXINT ( (1 << SPIDER_NET_GDTFDCINT) | \
- (1 << SPIDER_NET_GDTDCEINT) )
+#define SPIDER_NET_TXINT (1 << SPIDER_NET_GDTFDCINT)
/* We rely on flagged descriptor interrupts */
#define SPIDER_NET_RXINT ( (1 << SPIDER_NET_GDAFDCINT) )
struct work_struct tx_timeout_task;
atomic_t tx_timeout_task_counter;
wait_queue_head_t waitq;
+ int num_rx_ints;
+ int ignore_rx_ramfull;
/* for ethtool */
int msg_enable;
return 0;
}
-static uint32_t
-spider_net_ethtool_get_tx_csum(struct net_device *netdev)
-{
- return (netdev->features & NETIF_F_HW_CSUM) != 0;
-}
-
-static int
-spider_net_ethtool_set_tx_csum(struct net_device *netdev, uint32_t data)
-{
- if (data)
- netdev->features |= NETIF_F_HW_CSUM;
- else
- netdev->features &= ~NETIF_F_HW_CSUM;
-
- return 0;
-}
static void
spider_net_ethtool_get_ringparam(struct net_device *netdev,
.get_wol = spider_net_ethtool_get_wol,
.get_msglevel = spider_net_ethtool_get_msglevel,
.set_msglevel = spider_net_ethtool_set_msglevel,
+ .get_link = ethtool_op_get_link,
.nway_reset = spider_net_ethtool_nway_reset,
.get_rx_csum = spider_net_ethtool_get_rx_csum,
.set_rx_csum = spider_net_ethtool_set_rx_csum,
- .get_tx_csum = spider_net_ethtool_get_tx_csum,
- .set_tx_csum = spider_net_ethtool_set_tx_csum,
+ .get_tx_csum = ethtool_op_get_tx_csum,
+ .set_tx_csum = ethtool_op_set_tx_csum,
.get_ringparam = spider_net_ethtool_get_ringparam,
.get_strings = spider_net_get_strings,
.get_stats_count = spider_net_get_stats_count,
cur = lbuf;
- /* skip initial spaces */
- while (*cur && isspace(*cur))
- {
- cur++;
- }
-
switch ((long)data)
{
case LED_NOLCD:
u64 tod;
cpuid_t cpu_id;
u32 arch_id;
+ u32 volnr;
u32 build_arch;
+ u64 rmem_size;
char pad2[4016];
} __attribute__((packed,__aligned__(16)));
else
hdr->arch_id = DUMP_ARCH_S390;
hdr->mem_size = sys_info.mem_size;
+ hdr->rmem_size = sys_info.mem_size;
hdr->mem_end = sys_info.mem_size;
hdr->num_pages = sys_info.mem_size / PAGE_SIZE;
hdr->tod = get_clock();
add_channel(struct ccw_device *cdev,int i,struct claw_privbk *privptr)
{
struct chbk *p_ch;
+ struct ccw_dev_id dev_id;
#ifdef FUNCTRACE
printk(KERN_INFO "%s:%s Enter\n",cdev->dev.bus_id,__FUNCTION__);
p_ch = &privptr->channel[i];
p_ch->cdev = cdev;
snprintf(p_ch->id, CLAW_ID_SIZE, "cl-%s", cdev->dev.bus_id);
- sscanf(cdev->dev.bus_id+4,"%x",&p_ch->devno);
+ ccw_device_get_id(cdev, &dev_id);
+ p_ch->devno = dev_id.devno;
if ((p_ch->irb = kmalloc(sizeof (struct irb),GFP_KERNEL)) == NULL) {
printk(KERN_WARNING "%s Out of memory in %s for irb\n",
p_ch->id,__FUNCTION__);
struct claw_env *p_env;
struct net_device *dev;
int ret;
+ struct ccw_dev_id dev_id;
pr_debug("%s() called\n", __FUNCTION__);
printk(KERN_INFO "claw: add for %s\n",cgdev->cdev[READ]->dev.bus_id);
if (!privptr)
return -ENODEV;
p_env = privptr->p_env;
- sscanf(cgdev->cdev[READ]->dev.bus_id+4,"%x",
- &p_env->devno[READ]);
- sscanf(cgdev->cdev[WRITE]->dev.bus_id+4,"%x",
- &p_env->devno[WRITE]);
+ ccw_device_get_id(cgdev->cdev[READ], &dev_id);
+ p_env->devno[READ] = dev_id.devno;
+ ccw_device_get_id(cgdev->cdev[WRITE], &dev_id);
+ p_env->devno[WRITE] = dev_id.devno;
ret = add_channel(cgdev->cdev[0],0,privptr);
if (ret == 0)
ret = add_channel(cgdev->cdev[1],1,privptr);
*(((char*)ptr)+28),*(((char*)ptr)+29), \
*(((char*)ptr)+30),*(((char*)ptr)+31));
-static inline void iucv_hex_dump(unsigned char *buf, size_t len)
-{
- size_t i;
-
- for (i = 0; i < len; i++) {
- if (i && !(i % 16))
- printk("\n");
- printk("%02x ", *(buf + i));
- }
- printk("\n");
-}
-
#define PRINTK_HEADER " iucv: " /* for debugging */
static struct device_driver netiucv_driver = {
*/
static struct list_head iucv_connection_list =
LIST_HEAD_INIT(iucv_connection_list);
-static rwlock_t iucv_connection_rwlock = RW_LOCK_UNLOCKED;
+static DEFINE_RWLOCK(iucv_connection_rwlock);
/**
* Representation of event-data for the
*
* @returns The printable string (static data!!)
*/
-static inline char *netiucv_printname(char *name)
+static char *netiucv_printname(char *name)
{
static char tmp[9];
char *p = tmp;
* and throw away packet.
*/
if (fsm_getstate(privptr->fsm) != DEV_STATE_RUNNING) {
- fsm_event(privptr->fsm, DEV_EVENT_START, dev);
+ if (!in_atomic())
+ fsm_event(privptr->fsm, DEV_EVENT_START, dev);
dev_kfree_skb(skb);
privptr->stats.tx_dropped++;
privptr->stats.tx_errors++;
.attrs = netiucv_stat_attrs,
};
-static inline int netiucv_add_files(struct device *dev)
+static int netiucv_add_files(struct device *dev)
{
int ret;
return ret;
}
-static inline void netiucv_remove_files(struct device *dev)
+static void netiucv_remove_files(struct device *dev)
{
IUCV_DBF_TEXT(trace, 3, __FUNCTION__);
sysfs_remove_group(&dev->kobj, &netiucv_stat_attr_group);
/* prepare qdio hdr */
if (eddp->qh.hdr.l2.id == QETH_HEADER_TYPE_LAYER2){
eddp->qh.hdr.l2.pkt_length = data_len + ETH_HLEN +
- eddp->nhl + eddp->thl -
- sizeof(struct qeth_hdr);
+ eddp->nhl + eddp->thl;
#ifdef CONFIG_QETH_VLAN
if (eddp->mac.h_proto == __constant_htons(ETH_P_8021Q))
eddp->qh.hdr.l2.pkt_length += VLAN_HLEN;
card->use_hard_stop = 1;
__qeth_set_offline(card->gdev,1);
rc = __qeth_set_online(card->gdev,1);
+ /* don't run another scheduled recovery */
+ qeth_clear_thread_start_bit(card, QETH_RECOVER_THREAD);
+ qeth_clear_thread_running_bit(card, QETH_RECOVER_THREAD);
if (!rc)
PRINT_INFO("Device %s successfully recovered!\n",
CARD_BUS_ID(card));
else
PRINT_INFO("Device %s could not be recovered!\n",
CARD_BUS_ID(card));
- /* don't run another scheduled recovery */
- qeth_clear_thread_start_bit(card, QETH_RECOVER_THREAD);
- qeth_clear_thread_running_bit(card, QETH_RECOVER_THREAD);
return 0;
}
}
-static inline __u16
-__raw_devno_from_bus_id(char *id)
-{
- id += (strlen(id) - 4);
- return (__u16) simple_strtoul(id, &id, 16);
-}
-
static int
qeth_ulp_setup_cb(struct qeth_card *card, struct qeth_reply *reply,
unsigned long data)
int rc;
__u16 temp;
struct qeth_cmd_buffer *iob;
+ struct ccw_dev_id dev_id;
QETH_DBF_TEXT(setup,2,"ulpsetup");
memcpy(QETH_ULP_SETUP_FILTER_TOKEN(iob->data),
&card->token.ulp_filter_r, QETH_MPC_TOKEN_LENGTH);
- temp = __raw_devno_from_bus_id(CARD_DDEV_ID(card));
- memcpy(QETH_ULP_SETUP_CUA(iob->data), &temp, 2);
+ ccw_device_get_id(CARD_DDEV(card), &dev_id);
+ memcpy(QETH_ULP_SETUP_CUA(iob->data), &dev_id.devno, 2);
temp = (card->info.cula << 8) + card->info.unit_addr2;
memcpy(QETH_ULP_SETUP_REAL_DEVADDR(iob->data), &temp, 2);
rc = qeth_send_control_data(card, ULP_SETUP_SIZE, iob,
in_dev = in6_dev_get(netdev);
if (!in_dev)
continue;
- read_lock(&in_dev->lock);
+ read_lock_bh(&in_dev->lock);
qeth_add_mc6(card,in_dev);
- read_unlock(&in_dev->lock);
+ read_unlock_bh(&in_dev->lock);
in6_dev_put(in_dev);
}
#endif /* CONFIG_QETH_VLAN */
in6_dev = in6_dev_get(card->dev);
if (in6_dev == NULL)
return;
- read_lock(&in6_dev->lock);
+ read_lock_bh(&in6_dev->lock);
qeth_add_mc6(card, in6_dev);
qeth_add_vlan_mc6(card);
- read_unlock(&in6_dev->lock);
+ read_unlock_bh(&in6_dev->lock);
in6_dev_put(in6_dev);
}
#endif /* CONFIG_QETH_IPV6 */
QETH_DBF_TEXT_(setup, 2, "1err%d", rc);
if (rc == 0xe080){
PRINT_WARN("LAN on card %s if offline! "
- "Continuing softsetup.\n",
+ "Waiting for STARTLAN from card.\n",
CARD_BUS_ID(card));
card->lan_online = 0;
- } else
- return rc;
+ }
+ return rc;
} else
card->lan_online = 1;
if (card->info.type==QETH_CARD_TYPE_OSN)
}
/* fallthrough */
case QETH_CARD_TYPE_IQD:
- card->info.mcl_level[0] = (char) _ebcasc[(__u8)
- card->info.mcl_level[0]];
- card->info.mcl_level[1] = (char) _ebcasc[(__u8)
- card->info.mcl_level[1]];
- card->info.mcl_level[2] = (char) _ebcasc[(__u8)
- card->info.mcl_level[2]];
- card->info.mcl_level[3] = (char) _ebcasc[(__u8)
- card->info.mcl_level[3]];
- card->info.mcl_level[QETH_MCL_LENGTH] = 0;
+ if (card->info.guestlan) {
+ card->info.mcl_level[0] = (char) _ebcasc[(__u8)
+ card->info.mcl_level[0]];
+ card->info.mcl_level[1] = (char) _ebcasc[(__u8)
+ card->info.mcl_level[1]];
+ card->info.mcl_level[2] = (char) _ebcasc[(__u8)
+ card->info.mcl_level[2]];
+ card->info.mcl_level[3] = (char) _ebcasc[(__u8)
+ card->info.mcl_level[3]];
+ card->info.mcl_level[QETH_MCL_LENGTH] = 0;
+ }
break;
default:
memset(&card->info.mcl_level[0], 0, QETH_MCL_LENGTH + 1);
starget_for_each_device(tp->starget, NULL,
esp_clear_hold);
}
+ esp->flags &= ~ESP_FLAG_RESETTING;
}
/* Runs under host->lock */
int thread_wakeup_needed;
struct completion thread_notifier;
struct task_struct *thread_task;
- sigset_t thread_signal_mask;
int cmnd_size;
u8 cmnd[MAX_COMMAND_SIZE];
/* Clear the existing signals. Anything but SIGUSR1 is converted
* into a high-priority EXIT exception. */
for (;;) {
- sig = dequeue_signal_lock(current, &fsg->thread_signal_mask,
- &info);
+ sig = dequeue_signal_lock(current, ¤t->blocked, &info);
if (!sig)
break;
if (sig != SIGUSR1) {
/* Allow the thread to be killed by a signal, but set the signal mask
* to block everything but INT, TERM, KILL, and USR1. */
- siginitsetinv(&fsg->thread_signal_mask, sigmask(SIGINT) |
- sigmask(SIGTERM) | sigmask(SIGKILL) |
- sigmask(SIGUSR1));
- sigprocmask(SIG_SETMASK, &fsg->thread_signal_mask, NULL);
+ allow_signal(SIGINT);
+ allow_signal(SIGTERM);
+ allow_signal(SIGKILL);
+ allow_signal(SIGUSR1);
/* Arrange for userspace references to be interpreted as kernel
* pointers. That way we can pass a kernel pointer to a routine
/* verify that the device wasn't unplugged */
if (!dev->present) {
- mutex_unlock(&dev->mutex);
- return -ENODEV;
+ retval = -ENODEV;
+ goto error_out;
}
dbg("%s - minor %d, cmd 0x%.4x, arg %ld", __func__, dev->minor, cmd,
retval = -ENOTTY;
break;
}
-
+error_out:
/* unlock the device */
mutex_unlock(&dev->mutex);
+ kfree(buffer);
return retval;
}
size_t bulk_in_size; /* the size of the receive buffer */
__u8 bulk_in_endpointAddr; /* the address of the bulk in endpoint */
__u8 bulk_out_endpointAddr; /* the address of the bulk out endpoint */
- struct kref kref;
+ struct kref kref;
+ struct semaphore limit_sem; /* to stop writes at full throttle from
+ * using up all RAM */
};
#define to_lcd_dev(d) container_of(d, struct usb_lcd, kref)
+#define USB_LCD_CONCURRENT_WRITES 5
+
static struct usb_driver lcd_driver;
static DEFINE_MUTEX(usb_lcd_open_mutex);
/* free up our allocated buffer */
usb_buffer_free(urb->dev, urb->transfer_buffer_length,
urb->transfer_buffer, urb->transfer_dma);
+ up(&dev->limit_sem);
}
static ssize_t lcd_write(struct file *file, const char __user * user_buffer, size_t count, loff_t *ppos)
{
struct usb_lcd *dev;
- int retval = 0;
+ int retval = 0, r;
struct urb *urb = NULL;
char *buf = NULL;
if (count == 0)
goto exit;
+ r = down_interruptible(&dev->limit_sem);
+ if (r < 0)
+ return -EINTR;
+
/* create a urb, and a buffer for it, and copy the data to the urb */
urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!urb)
- return -ENOMEM;
+ if (!urb) {
+ retval = -ENOMEM;
+ goto err_no_buf;
+ }
buf = usb_buffer_alloc(dev->udev, count, GFP_KERNEL, &urb->transfer_dma);
if (!buf) {
error:
usb_buffer_free(dev->udev, count, buf, urb->transfer_dma);
usb_free_urb(urb);
+err_no_buf:
+ up(&dev->limit_sem);
return retval;
}
goto error;
}
kref_init(&dev->kref);
+ sema_init(&dev->limit_sem, USB_LCD_CONCURRENT_WRITES);
dev->udev = usb_get_dev(interface_to_usbdev(interface));
dev->interface = interface;
{ USB_DEVICE(FTDI_VID, FTDI_ACTZWAVE_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_IRTRANS_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_IPLUS_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_IPLUS2_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_DMX4ALL) },
{ USB_DEVICE(FTDI_VID, FTDI_SIO_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) },
/* iPlus device */
#define FTDI_IPLUS_PID 0xD070 /* Product Id */
+#define FTDI_IPLUS2_PID 0xD071 /* Product Id */
/* DMX4ALL DMX Interfaces */
#define FTDI_DMX4ALL 0xC850
}
/* free up our endpoint stuff */
if (edge_serial->is_epic) {
- usb_unlink_urb(edge_serial->interrupt_read_urb);
+ usb_kill_urb(edge_serial->interrupt_read_urb);
usb_free_urb(edge_serial->interrupt_read_urb);
kfree(edge_serial->interrupt_in_buffer);
- usb_unlink_urb(edge_serial->read_urb);
+ usb_kill_urb(edge_serial->read_urb);
usb_free_urb(edge_serial->read_urb);
kfree(edge_serial->bulk_in_buffer);
}
#define NOVATELWIRELESS_VENDOR_ID 0x1410
#define ANYDATA_VENDOR_ID 0x16d5
-#define ANYDATA_PRODUCT_ID 0x6501
+#define ANYDATA_PRODUCT_ADU_E100A 0x6501
+#define ANYDATA_PRODUCT_ADU_500A 0x6502
#define BANDRICH_VENDOR_ID 0x1A8D
#define BANDRICH_PRODUCT_C100_1 0x1002
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, 0x2110) }, /* Novatel Merlin ES620 / Merlin ES720 / Ovation U720 */
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, 0x2130) }, /* Novatel Merlin ES620 SM Bus */
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, 0x2410) }, /* Novatel EU740 */
- { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ID) },
+ { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_E100A) },
+ { USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) },
{ USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) },
{ USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) },
{ USB_DEVICE(DELL_VENDOR_ID, 0x8118) }, /* Dell Wireless 5510 Mobile Broadband HSDPA ExpressCard */
spin_lock_irqsave(&tport->tp_lock, flags);
if (tport->tp_read_urb_state == TI_READ_URB_STOPPED) {
+ tport->tp_read_urb_state = TI_READ_URB_RUNNING;
urb = tport->tp_port->read_urb;
+ spin_unlock_irqrestore(&tport->tp_lock, flags);
urb->complete = ti_bulk_in_callback;
urb->context = tport;
urb->dev = tport->tp_port->serial->dev;
status = usb_submit_urb(urb, GFP_KERNEL);
+ } else {
+ tport->tp_read_urb_state = TI_READ_URB_RUNNING;
+ spin_unlock_irqrestore(&tport->tp_lock, flags);
}
- tport->tp_read_urb_state = TI_READ_URB_RUNNING;
-
- spin_unlock_irqrestore(&tport->tp_lock, flags);
return status;
}
sb->s_flags = (sb->s_flags & ~MS_POSIXACL) |
((sbi->s_mount_opt & EXT2_MOUNT_POSIX_ACL) ? MS_POSIXACL : 0);
+ ext2_xip_verify_sb(sb); /* see if bdev supports xip, unset
+ EXT2_MOUNT_XIP if not */
+
+ if ((ext2_use_xip(sb)) && (sb->s_blocksize != PAGE_SIZE)) {
+ printk("XIP: Unsupported blocksize\n");
+ goto restore_opts;
+ }
+
es = sbi->s_es;
if (((sbi->s_mount_opt & EXT2_MOUNT_XIP) !=
(old_mount_opt & EXT2_MOUNT_XIP)) &&
*/
ei->i_extra_isize = le16_to_cpu(raw_inode->i_extra_isize);
if (EXT3_GOOD_OLD_INODE_SIZE + ei->i_extra_isize >
- EXT3_INODE_SIZE(inode->i_sb))
+ EXT3_INODE_SIZE(inode->i_sb)) {
+ brelse (bh);
goto bad_inode;
+ }
if (ei->i_extra_isize == 0) {
/* The extra space is currently unused. Use it. */
ei->i_extra_isize = sizeof(struct ext3_inode) -
*/
ei->i_extra_isize = le16_to_cpu(raw_inode->i_extra_isize);
if (EXT4_GOOD_OLD_INODE_SIZE + ei->i_extra_isize >
- EXT4_INODE_SIZE(inode->i_sb))
+ EXT4_INODE_SIZE(inode->i_sb)) {
+ brelse (bh);
goto bad_inode;
+ }
if (ei->i_extra_isize == 0) {
/* The extra space is currently unused. Use it. */
ei->i_extra_isize = sizeof(struct ext4_inode) -
if (status)
goto unlock;
- memclear_highpage_flush(page, offset, bytes);
+ zero_user_page(page, offset, bytes, KM_USER0);
status = mapping->a_ops->commit_write(NULL, page, offset,
offset + bytes);
#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
static inline void SSYNC (void)
{
- __builtin_bfin_ssync();
+ __asm__ __volatile__ ("nop; nop; nop;\n\t"
+ "ssync;\n\t"
+ ::);
}
#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
static inline void SSYNC (void)
#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
static inline void CSYNC (void)
{
- __builtin_bfin_csync();
+ __asm__ __volatile__ ("nop; nop; nop;\n\t"
+ "ssync;\n\t"
+ ::);
}
#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
static inline void CSYNC (void)
}
#endif
+#else /* __ASSEMBLY__ */
+
+/* SSYNC & CSYNC implementations for assembly files */
+
+#define ssync(x) SSYNC(x)
+#define csync(x) CSYNC(x)
+
+#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
+#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
+
+#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
+#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
+#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
+
+#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#define SSYNC(scratch) nop; nop; nop; SSYNC;
+#define CSYNC(scratch) nop; nop; nop; CSYNC;
+
+#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
+#define SSYNC(scratch) SSYNC;
+#define CSYNC(scratch) CSYNC;
+
+#endif /* ANOMALY_05000312 & ANOMALY_05000244 handling */
+
#endif /* __ASSEMBLY__ */
#endif /* _BLACKFIN_H_ */
#define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent(d, s, h, f)
#define dma_free_noncoherent(d, s, v, h) dma_free_coherent(d, s, v, h)
+#define dma_mapping_error
+
/*
* Map a single buffer of the indicated size for DMA in streaming mode.
* The 32-bit bus address to use is returned.
*/
#ifndef __ASSEMBLY__
-static inline unsigned char readb(void __iomem *addr)
+static inline unsigned char readb(const volatile void __iomem *addr)
{
unsigned int val;
int tmp;
return (unsigned char) val;
}
-static inline unsigned short readw(void __iomem *addr)
+static inline unsigned short readw(const volatile void __iomem *addr)
{
unsigned int val;
int tmp;
return (unsigned short) val;
}
-static inline unsigned int readl(void __iomem *addr)
+static inline unsigned int readl(const volatile void __iomem *addr)
{
unsigned int val;
int tmp;
#endif
/* Issues that are common to 0.5, 0.4, and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
+#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) \
+ || defined(CONFIG_BF_REV_0_3))
#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
slot1 and store of a P register in slot 2 is not
supported */
control */
#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
killed in a particular stage*/
+#define ANOMALY_05000311 /* Erroneous flag pin operations under specific
+ sequences */
#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
registers are interrupted */
-#define ANOMALY_05000311 /* Erroneous flag pin operations under specific sequences*/
-
-#endif
+#define ANOMALY_05000313 /* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously On
+ * Next System MMR Access */
+#define ANOMALY_05000319 /* Internal Voltage Regulator Values of 1.05V, 1.10V
+ * and 1.15V Not Allowed for LQFP Packages */
+#endif /* Issues that are common to 0.5, 0.4, and 0.3 silicon */
/* These issues only occur on 0.3 or 0.4 BF533 */
#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
internal voltage regulator (VDDint) to increase. */
#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
internal voltage regulator (VDDint) to decrease */
-#endif
+#endif /* issues only occur on 0.3 or 0.4 BF533 */
/* These issues are only on 0.4 silicon */
#if (defined(CONFIG_BF_REV_0_4))
#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */
#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
(TDM) */
-#endif
+#endif /* issues are only on 0.4 silicon */
/* These issues are only on 0.3 silicon */
#if defined(CONFIG_BF_REV_0_3)
#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame
Sync Transmit Mode */
#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */
+#endif /* only on 0.3 silicon */
+
+#if defined(CONFIG_BF_REV_0_2)
+#define ANOMALY_05000067 /* Watchpoints (Hardware Breakpoints) are not
+ * supported */
+#define ANOMALY_05000109 /* Reserved bits in SYSCFG register not set at
+ * power on */
+#define ANOMALY_05000116 /* Trace Buffers may record discontinuities into
+ * emulation mode and/or exception, NMI, reset
+ * handlers */
+#define ANOMALY_05000123 /* DTEST_COMMAND initiated memory access may be
+ * incorrect if data cache or DMA is active */
+#define ANOMALY_05000124 /* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1,
+ * or 1:1 */
+#define ANOMALY_05000125 /* Erroneous exception when enabling cache */
+#define ANOMALY_05000126 /* SPI clock polarity and phase bits incorrect
+ * during booting */
+#define ANOMALY_05000137 /* DMEM_CONTROL is not set on Reset */
+#define ANOMALY_05000138 /* SPI boot will not complete if there is a zero fill
+ * block in the loader file */
+#define ANOMALY_05000140 /* Allowing the SPORT RX FIFO to fill will cause an
+ * overflow */
+#define ANOMALY_05000141 /* An Infinite Stall occurs with a particular sequence
+ * of consecutive dual dag events */
+#define ANOMALY_05000142 /* Interrupts may be lost when a programmable input
+ * flag is configured to be edge sensitive */
+#define ANOMALY_05000143 /* A read from external memory may return a wrong
+ * value with data cache enabled */
+#define ANOMALY_05000144 /* DMA and TESTSET conflict when both are accessing
+ * external memory */
+#define ANOMALY_05000145 /* In PWM_OUT mode, you must enable the PPI block to
+ * generate a waveform from PPI_CLK */
+#define ANOMALY_05000146 /* MDMA may lose the first few words of a descriptor
+ * chain */
+#define ANOMALY_05000147 /* The source MDMA descriptor may stop with a DMA
+ * Error */
+#define ANOMALY_05000148 /* When booting from a 16-bit asynchronous memory
+ * device, the upper 8-bits of each word must be
+ * 0x00 */
+#define ANOMALY_05000153 /* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000154 /* SPORT TFS signal is active in Multi-channel mode
+ * outside of valid channels */
+#define ANOMALY_05000155 /* Timer1 can not be used for PWMOUT mode when a
+ * certain PPI mode is in use */
+#define ANOMALY_05000157 /* A killed 32-bit System MMR write will lead to
+ * the next system MMR access thinking it should be
+ * 32-bit. */
+#define ANOMALY_05000163 /* SPORT transmit data is not gated by external frame
+ * sync in certain conditions */
+#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost
+ * write-through cache data writes */
+#define ANOMALY_05000173 /* DMA vs Core accesses to external memory */
+#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
+#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
+ * accumulator saturation */
+#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
+ * registers */
+#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000191 /* PPI does not invert the Driving PPICLK edge in
+ * Transmit Modes */
+#define ANOMALY_05000192 /* In PPI Transmit Modes with External Frame Syncs
+ * POLC */
+#define ANOMALY_05000206 /* Internal Voltage Regulator may not start up */
+
#endif
#endif /* _MACH_ANOMALY_H_ */
};
struct bfin_serial_res bfin_serial_resource[] = {
+ {
0xFFC00400,
IRQ_UART_RX,
#ifdef CONFIG_SERIAL_BFIN_DMA
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
+ }
};
control */
#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
killed in a particular stage*/
+#define ANOMALY_05000310 /* False hardware errors caused by fetches at the
+ * boundary of reserved memory */
#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
registers are interrupted */
+#define ANOMALY_05000313 /* PPI is level sensitive on first transfer */
+#define ANOMALY_05000322 /* EMAC RMII mode at 10-Base-T speed: RX frames not
+ * received properly */
#endif
#if defined(CONFIG_BF_REV_0_2)
DMA system instability */
#define ANOMALY_05000280 /* SPI Master boot mode does not work well with
Atmel Dataflash devices */
-
+#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context
+ * is not restored */
+#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
+ * control */
+#define ANOMALY_05000283 /* System MMR Write Is Stalled Indefinitely When
+ * Killed in a Particular Stage */
+#define ANOMALY_05000285 /* New Feature: EMAC TX DMA Word Alignment
+ * (Not Available On Older Silicon) */
+#define ANOMALY_05000288 /* SPORTs may receive bad data if FIFOs fill up */
+#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously
+ * On Next System MMR Access */
+#define ANOMALY_05000316 /* EMAC RMII mode: collisions occur in Full Duplex
+ * mode */
+#define ANOMALY_05000321 /* EMAC RMII mode: TX frames in half duplex fail with
+ * status No Carrier */
#endif /* CONFIG_BF_REV_0_2 */
#endif /* _MACH_ANOMALY_H_ */
};
struct bfin_serial_res bfin_serial_resource[] = {
+ {
0xFFC00400,
IRQ_UART_RX,
#ifdef CONFIG_SERIAL_BFIN_DMA
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
+ }
};
#define bfin_read_SRAM_BASE_ADDRESS() bfin_read32(SRAM_BASE_ADDRESS)
#define bfin_write_SRAM_BASE_ADDRESS(val) bfin_write32(SRAM_BASE_ADDRESS,val)
#define bfin_read_DMEM_CONTROL() bfin_read32(DMEM_CONTROL)
+#ifdef ANOMALY_05000125
+static __inline__ void bfin_write_DMEM_CONTROL(unsigned int val)
+{
+ unsigned long flags, iwr;
+
+ local_irq_save(flags);
+ __asm__(".align 8\n");
+ bfin_write32(IMEM_CONTROL, val);
+ __builtin_bfin_ssync();
+ local_irq_restore(flags);
+}
+#else
#define bfin_write_DMEM_CONTROL(val) bfin_write32(DMEM_CONTROL,val)
+#endif
#define bfin_read_DCPLB_STATUS() bfin_read32(DCPLB_STATUS)
#define bfin_write_DCPLB_STATUS(val) bfin_write32(DCPLB_STATUS,val)
#define bfin_read_DCPLB_FAULT_ADDR() bfin_read32(DCPLB_FAULT_ADDR)
#define DTEST_DATA3 0xFFE0040C
*/
#define bfin_read_IMEM_CONTROL() bfin_read32(IMEM_CONTROL)
+#ifdef ANOMALY_05000125
+static __inline__ void bfin_write_IMEM_CONTROL(unsigned int val)
+{
+ unsigned long flags, iwr;
+
+ local_irq_save(flags);
+ __asm__(".align 8\n");
+ bfin_write32(IMEM_CONTROL, val);
+ __builtin_bfin_ssync();
+ local_irq_restore(flags);
+
+}
+#else
#define bfin_write_IMEM_CONTROL(val) bfin_write32(IMEM_CONTROL,val)
+#endif
#define bfin_read_ICPLB_STATUS() bfin_read32(ICPLB_STATUS)
#define bfin_write_ICPLB_STATUS(val) bfin_write32(ICPLB_STATUS,val)
#define bfin_read_ICPLB_FAULT_ADDR() bfin_read32(ICPLB_FAULT_ADDR)
#define __ARCH_WANT_SYS_NICE
#define __ARCH_WANT_SYS_RT_SIGACTION
#define __ARCH_WANT_SYS_RT_SIGSUSPEND
-#endif
/*
* "Conditional" syscalls
*/
#define cond_syscall(x) asm(".weak\t_" #x "\n\t.set\t_" #x ",_sys_ni_syscall");
+#endif /* __KERNEL__ */
+
#endif /* __ASM_BFIN_UNISTD_H */
return 0;
}
+extern int forbid_dac;
+
static inline int
dma_supported(struct device *dev, u64 mask)
{
if(mask < 0x00ffffff)
return 0;
+ /* Work around chipset bugs */
+ if (forbid_dac > 0 && mask > 0xffffffffULL)
+ return 0;
+
return 1;
}
val = paravirt_read_msr(msr, &_err); \
} while(0)
-#define wrmsrl(msr,val) ((void)paravirt_write_msr(msr, val, 0))
+#define wrmsrl(msr,val) wrmsr(msr, (u32)((u64)(val)), ((u64)(val))>>32)
#define wrmsr_safe(msr,a,b) paravirt_write_msr(msr, a, b)
/* rdmsr with exception handling */
if (cpu_has_llsc && R10000_LLSC_WAR) {
unsigned long *m = ((unsigned long *) addr) + (nr >> SZLONG_LOG);
- unsigned long temp, res;
+ unsigned long temp;
__asm__ __volatile__(
" .set mips3 \n"
#include <asm/uaccess.h>
+#define SI_PAD_SIZE32 ((SI_MAX_SIZE/sizeof(int)) - 3)
+
+typedef struct compat_siginfo {
+ int si_signo;
+ int si_code;
+ int si_errno;
+
+ union {
+ int _pad[SI_PAD_SIZE32];
+
+ /* kill() */
+ struct {
+ compat_pid_t _pid; /* sender's pid */
+ compat_uid_t _uid; /* sender's uid */
+ } _kill;
+
+ /* SIGCHLD */
+ struct {
+ compat_pid_t _pid; /* which child */
+ compat_uid_t _uid; /* sender's uid */
+ int _status; /* exit code */
+ compat_clock_t _utime;
+ compat_clock_t _stime;
+ } _sigchld;
+
+ /* IRIX SIGCHLD */
+ struct {
+ compat_pid_t _pid; /* which child */
+ compat_clock_t _utime;
+ int _status; /* exit code */
+ compat_clock_t _stime;
+ } _irix_sigchld;
+
+ /* SIGILL, SIGFPE, SIGSEGV, SIGBUS */
+ struct {
+ s32 _addr; /* faulting insn/memory ref. */
+ } _sigfault;
+
+ /* SIGPOLL, SIGXFSZ (To do ...) */
+ struct {
+ int _band; /* POLL_IN, POLL_OUT, POLL_MSG */
+ int _fd;
+ } _sigpoll;
+
+ /* POSIX.1b timers */
+ struct {
+ timer_t _tid; /* timer id */
+ int _overrun; /* overrun count */
+ compat_sigval_t _sigval;/* same as below */
+ int _sys_private; /* not to be passed to user */
+ } _timer;
+
+ /* POSIX.1b signals */
+ struct {
+ compat_pid_t _pid; /* sender's pid */
+ compat_uid_t _uid; /* sender's uid */
+ compat_sigval_t _sigval;
+ } _rt;
+
+ } _sifields;
+} compat_siginfo_t;
+
static inline int __copy_conv_sigset_to_user(compat_sigset_t __user *d,
const sigset_t *s)
{
extern void alloc_legacy_irqno(void);
extern void free_irqno(unsigned int irq);
+/*
+ * Before R2 the timer and performance counter interrupts were both fixed to
+ * IE7. Since R2 their number has to be read from the c0_intctl register.
+ */
+#define CP0_LEGACY_COMPARE_IRQ 7
+
+extern int cp0_compare_irq;
+extern int cp0_perfcount_irq;
+
#endif /* _ASM_IRQ_H */
#include <irq.h>
-/*
- * Interrupts 0..7 are used for Atlas CPU interrupts (nonEIC mode)
- */
-#define MIPSCPU_INT_BASE MIPS_CPU_IRQ_BASE
-
/* CPU interrupt offsets */
#define MIPSCPU_INT_SW0 0
#define MIPSCPU_INT_SW1 1
#define MIPSCPU_INT_MB2 4
#define MIPSCPU_INT_MB3 5
#define MIPSCPU_INT_MB4 6
-#define MIPSCPU_INT_CPUCTR 7
/*
* Interrupts 8..39 are used for Atlas interrupt controller interrupts
*/
#define MALTA_INT_BASE 0
-/*
- * Interrupts 16..23 are used for Malta CPU interrupts (nonEIC mode)
- */
-#define MIPSCPU_INT_BASE MIPS_CPU_IRQ_BASE
-
/* CPU interrupt offsets */
#define MIPSCPU_INT_SW0 0
#define MIPSCPU_INT_SW1 1
#define MIPSCPU_INT_COREHI MIPSCPU_INT_MB3
#define MIPSCPU_INT_MB4 6
#define MIPSCPU_INT_CORELO MIPSCPU_INT_MB4
-#define MIPSCPU_INT_CPUCTR 7
/*
* Interrupts 64..127 are used for Soc-it Classic interrupts
#include <irq.h>
-/*
- * Interrupts 0..7 are used for SEAD CPU interrupts
- */
-#define MIPSCPU_INT_BASE MIPS_CPU_IRQ_BASE
-
#define MIPSCPU_INT_UART0 2
#define MIPSCPU_INT_UART1 3
-#define MIPSCPU_INT_CPUCTR 7
-
#endif /* !(_MIPS_SEADINT_H) */
#define SIM_INT_BASE 0
#define MIPSCPU_INT_MB0 2
-#define MIPSCPU_INT_BASE MIPS_CPU_IRQ_BASE
#define MIPS_CPU_TIMER_IRQ 7
-#define MIPSCPU_INT_CPUCTR 7
-
#define MSC01E_INT_BASE 64
-#define MIPSCPU_INT_CPUCTR 7
#define MSC01E_INT_CPUCTR 11
#endif
#define MODULE_KERNEL_TYPE "64BIT "
#endif
-#define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY MODULE_KERNEL_TYPE
+#ifdef CONFIG_MIPS_MT_SMTC
+#define MODULE_KERNEL_SMTC "MT_SMTC "
+#else
+#define MODULE_KERNEL_SMTC ""
+#endif
+
+#define MODULE_ARCH_VERMAGIC \
+ MODULE_PROC_FAMILY MODULE_KERNEL_TYPE MODULE_KERNEL_SMTC
#endif /* _ASM_MODULE_H */
# define __lock_aligned __attribute__((__section__(".data.lock_aligned")))
#endif
-#define KERNEL_START (0x10100000 - 0x1000)
#define arch_align_stack(x) (x)
#endif
barrier();
}
+static inline void psw_set_key(unsigned int key)
+{
+ asm volatile("spka 0(%0)" : : "d" (key));
+}
+
/*
* Set PSW to specified value.
*/
#define regs_return_value(regs)((regs)->gprs[2])
#define profile_pc(regs) instruction_pointer(regs)
extern void show_regs(struct pt_regs * regs);
-#endif
-
-static inline void
-psw_set_key(unsigned int key)
-{
- asm volatile("spka 0(%0)" : : "d" (key));
-}
-
+#endif /* __KERNEL__ */
#endif /* __ASSEMBLY__ */
#endif /* _S390_PTRACE_H */
#ifndef __UM_BUG_H
#define __UM_BUG_H
-#include <asm/arch/bug.h>
+#include <asm-generic/bug.h>
#endif
__ex_table : { *(__ex_table) }
__stop___ex_table = .;
+ BUG_TABLE
+
__uml_setup_start = .;
.uml.setup.init : { *(.uml.setup.init) }
__uml_setup_end = .;
--- /dev/null
+#ifndef __UM_PARAVIRT_H
+#define __UM_PARAVIRT_H
+
+#include "asm/arch/paravirt.h"
+
+#endif
__SYSCALL(__NR_epoll_pwait, sys_epoll_pwait)
#define __NR_signalfd 282
__SYSCALL(__NR_signalfd, sys_signalfd)
-#define __NR_timerfd 282
+#define __NR_timerfd 283
__SYSCALL(__NR_timerfd, sys_timerfd)
-#define __NR_eventfd 283
+#define __NR_eventfd 284
__SYSCALL(__NR_eventfd, sys_eventfd)
#ifndef __NO_STUBS
__mark_inode_dirty(inode, I_DIRTY_SYNC);
}
+/**
+ * inc_nlink - directly increment an inode's link count
+ * @inode: inode
+ *
+ * This is a low-level filesystem helper to replace any
+ * direct filesystem manipulation of i_nlink. Currently,
+ * it is only here for parity with dec_nlink().
+ */
static inline void inc_nlink(struct inode *inode)
{
inode->i_nlink++;
mark_inode_dirty(inode);
}
+/**
+ * drop_nlink - directly drop an inode's link count
+ * @inode: inode
+ *
+ * This is a low-level filesystem helper to replace any
+ * direct filesystem manipulation of i_nlink. In cases
+ * where we are attempting to track writes to the
+ * filesystem, a decrement to zero means an imminent
+ * write when the file is truncated and actually unlinked
+ * on the filesystem.
+ */
static inline void drop_nlink(struct inode *inode)
{
inode->i_nlink--;
}
+/**
+ * clear_nlink - directly zero an inode's link count
+ * @inode: inode
+ *
+ * This is a low-level filesystem helper to replace any
+ * direct filesystem manipulation of i_nlink. See
+ * drop_nlink() for why we care about i_nlink hitting zero.
+ */
static inline void clear_nlink(struct inode *inode)
{
inode->i_nlink = 0;
#define FUTEX_LOCK_PI 6
#define FUTEX_UNLOCK_PI 7
#define FUTEX_TRYLOCK_PI 8
-#define FUTEX_CMP_REQUEUE_PI 9
#define FUTEX_PRIVATE_FLAG 128
#define FUTEX_CMD_MASK ~FUTEX_PRIVATE_FLAG
*/
#define FUTEX_OWNER_DIED 0x40000000
-/*
- * Some processes have been requeued on this PI-futex
- */
-#define FUTEX_WAITER_REQUEUED 0x20000000
-
/*
* The rest of the robust-futex field is for the TID:
*/
-#define FUTEX_TID_MASK 0x0fffffff
+#define FUTEX_TID_MASK 0x3fffffff
/*
* This limit protects against a deliberately circular list.
#define FUT_OFF_MMSHARED 2 /* We set bit 1 if key has a reference on mm */
union futex_key {
- u32 __user *uaddr;
struct {
unsigned long pgoff;
struct inode *inode;
#include <linux/netdevice.h>
#include <linux/rcupdate.h>
#include <linux/timer.h>
+#include <linux/sysctl.h>
struct ipv4_devconf
{
MLX4_CMD_INIT_PORT = 0x9,
MLX4_CMD_CLOSE_PORT = 0xa,
MLX4_CMD_QUERY_HCA = 0xb,
+ MLX4_CMD_QUERY_PORT = 0x43,
MLX4_CMD_SET_PORT = 0xc,
MLX4_CMD_ACCESS_DDR = 0x2e,
MLX4_CMD_MAP_ICM = 0xffa,
enum {
MLX4_FLAG_MSI_X = 1 << 0,
+ MLX4_FLAG_OLD_PORT_CMDS = 1 << 1,
};
enum {
struct mlx4_caps {
u64 fw_ver;
int num_ports;
- int vl_cap;
- int mtu_cap;
- int gid_table_len;
- int pkey_table_len;
+ int vl_cap[MLX4_MAX_PORTS + 1];
+ int mtu_cap[MLX4_MAX_PORTS + 1];
+ int gid_table_len[MLX4_MAX_PORTS + 1];
+ int pkey_table_len[MLX4_MAX_PORTS + 1];
int local_ca_ack_delay;
int num_uars;
int bf_reg_size;
u32 page_size_cap;
u32 flags;
u16 stat_rate_support;
- u8 port_width_cap;
+ u8 port_width_cap[MLX4_MAX_PORTS + 1];
};
struct mlx4_buf_list {
void mlx4_srq_free(struct mlx4_dev *dev, struct mlx4_srq *srq);
int mlx4_srq_arm(struct mlx4_dev *dev, struct mlx4_srq *srq, int limit_watermark);
-int mlx4_INIT_PORT(struct mlx4_dev *dev, struct mlx4_init_port_param *param, int port);
+int mlx4_INIT_PORT(struct mlx4_dev *dev, int port);
int mlx4_CLOSE_PORT(struct mlx4_dev *dev, int port);
int mlx4_multicast_attach(struct mlx4_dev *dev, struct mlx4_qp *qp, u8 gid[16]);
__be64 addr;
};
+enum {
+ MLX4_INLINE_ALIGN = 64,
+};
+
struct mlx4_wqe_inline_seg {
__be32 byte_count;
};
if (unlikely(PageSwapCache(page)))
mapping = &swapper_space;
+#ifdef CONFIG_SLUB
+ else if (unlikely(PageSlab(page)))
+ mapping = NULL;
+#endif
else if (unlikely((unsigned long)mapping & PAGE_MAPPING_ANON))
mapping = NULL;
return mapping;
* to do various tricks to work around compiler limitations in order to
* ensure proper constant folding.
*/
-#define KMALLOC_SHIFT_HIGH ((MAX_ORDER + PAGE_SHIFT) <= 25 ? \
- (MAX_ORDER + PAGE_SHIFT) : 25)
+#define KMALLOC_SHIFT_HIGH ((MAX_ORDER + PAGE_SHIFT - 1) <= 25 ? \
+ (MAX_ORDER + PAGE_SHIFT - 1) : 25)
#define KMALLOC_MAX_SIZE (1UL << KMALLOC_SHIFT_HIGH)
#define KMALLOC_MAX_ORDER (KMALLOC_SHIFT_HIGH - PAGE_SHIFT)
#define SM501_DEBUG_CONTROL (0x000034)
/* power management */
+#define SM501_POWERMODE_P2X_SRC (1<<29)
+#define SM501_POWERMODE_V2X_SRC (1<<20)
+#define SM501_POWERMODE_M_SRC (1<<12)
+#define SM501_POWERMODE_M1_SRC (1<<4)
+
#define SM501_CURRENT_GATE (0x000038)
#define SM501_CURRENT_CLOCK (0x00003C)
#define SM501_POWER_MODE_0_GATE (0x000040)
#define SM501_DEVICEID (0x000060)
/* 0x050100A0 */
+#define SM501_DEVICEID_SM501 (0x05010000)
+#define SM501_DEVICEID_IDMASK (0xffff0000)
+
#define SM501_PLLCLOCK_COUNT (0x000064)
#define SM501_MISC_TIMING (0x000068)
#define SM501_CURRENT_SDRAM_CLOCK (0x00006C)
/* If the update involves invalidating rules, do the inode-based
* filtering now, so we don't omit records. */
- if (invalidating &&
+ if (invalidating && current->audit_context &&
audit_filter_inodes(current, current->audit_context) == AUDIT_RECORD_CONTEXT)
audit_set_auditable(current->audit_context);
#include "rtmutex_common.h"
-#ifdef CONFIG_DEBUG_RT_MUTEXES
-# include "rtmutex-debug.h"
-#else
-# include "rtmutex.h"
-#endif
-
#define FUTEX_HASHBITS (CONFIG_BASE_SMALL ? 4 : 8)
/*
/* Optional priority inheritance state: */
struct futex_pi_state *pi_state;
struct task_struct *task;
-
- /*
- * This waiter is used in case of requeue from a
- * normal futex to a PI-futex
- */
- struct rt_mutex_waiter waiter;
};
/*
if (unlikely((vma->vm_flags & (VM_IO|VM_READ)) != VM_READ))
return (vma->vm_flags & VM_IO) ? -EPERM : -EACCES;
- /* Save the user address in the ley */
- key->uaddr = uaddr;
-
/*
* Private mappings are handled in a simple way.
*
rcu_read_lock();
p = find_task_by_pid(pid);
- if (!p)
- goto out_unlock;
- if ((current->euid != p->euid) && (current->euid != p->uid)) {
- p = NULL;
- goto out_unlock;
- }
- get_task_struct(p);
-out_unlock:
+
+ if (!p || ((current->euid != p->euid) && (current->euid != p->uid)))
+ p = ERR_PTR(-ESRCH);
+ else
+ get_task_struct(p);
+
rcu_read_unlock();
return p;
int ret = 0;
newval = FUTEX_WAITERS | new_owner->pid;
- /* Keep the FUTEX_WAITER_REQUEUED flag if it was set */
- newval |= (uval & FUTEX_WAITER_REQUEUED);
pagefault_disable();
curval = futex_atomic_cmpxchg_inatomic(uaddr, uval, newval);
return ret;
}
-/*
- * Called from futex_requeue_pi.
- * Set FUTEX_WAITERS and FUTEX_WAITER_REQUEUED flags on the
- * PI-futex value; search its associated pi_state if an owner exist
- * or create a new one without owner.
- */
-static inline int
-lookup_pi_state_for_requeue(u32 __user *uaddr, struct futex_hash_bucket *hb,
- union futex_key *key,
- struct futex_pi_state **pi_state)
-{
- u32 curval, uval, newval;
-
-retry:
- /*
- * We can't handle a fault cleanly because we can't
- * release the locks here. Simply return the fault.
- */
- if (get_futex_value_locked(&curval, uaddr))
- return -EFAULT;
-
- /* set the flags FUTEX_WAITERS and FUTEX_WAITER_REQUEUED */
- if ((curval & (FUTEX_WAITERS | FUTEX_WAITER_REQUEUED))
- != (FUTEX_WAITERS | FUTEX_WAITER_REQUEUED)) {
- /*
- * No waiters yet, we prepare the futex to have some waiters.
- */
-
- uval = curval;
- newval = uval | FUTEX_WAITERS | FUTEX_WAITER_REQUEUED;
-
- pagefault_disable();
- curval = futex_atomic_cmpxchg_inatomic(uaddr, uval, newval);
- pagefault_enable();
-
- if (unlikely(curval == -EFAULT))
- return -EFAULT;
- if (unlikely(curval != uval))
- goto retry;
- }
-
- if (!(curval & FUTEX_TID_MASK)
- || lookup_pi_state(curval, hb, key, pi_state)) {
- /* the futex has no owner (yet) or the lookup failed:
- allocate one pi_state without owner */
-
- *pi_state = alloc_pi_state();
-
- /* Already stores the key: */
- (*pi_state)->key = *key;
-
- /* init the mutex without owner */
- __rt_mutex_init(&(*pi_state)->pi_mutex, NULL);
- }
-
- return 0;
-}
-
-/*
- * Keep the first nr_wake waiter from futex1, wake up one,
- * and requeue the next nr_requeue waiters following hashed on
- * one physical page to another physical page (PI-futex uaddr2)
- */
-static int futex_requeue_pi(u32 __user *uaddr1,
- struct rw_semaphore *fshared,
- u32 __user *uaddr2,
- int nr_wake, int nr_requeue, u32 *cmpval)
-{
- union futex_key key1, key2;
- struct futex_hash_bucket *hb1, *hb2;
- struct plist_head *head1;
- struct futex_q *this, *next;
- struct futex_pi_state *pi_state2 = NULL;
- struct rt_mutex_waiter *waiter, *top_waiter = NULL;
- struct rt_mutex *lock2 = NULL;
- int ret, drop_count = 0;
-
- if (refill_pi_state_cache())
- return -ENOMEM;
-
-retry:
- /*
- * First take all the futex related locks:
- */
- if (fshared)
- down_read(fshared);
-
- ret = get_futex_key(uaddr1, fshared, &key1);
- if (unlikely(ret != 0))
- goto out;
- ret = get_futex_key(uaddr2, fshared, &key2);
- if (unlikely(ret != 0))
- goto out;
-
- hb1 = hash_futex(&key1);
- hb2 = hash_futex(&key2);
-
- double_lock_hb(hb1, hb2);
-
- if (likely(cmpval != NULL)) {
- u32 curval;
-
- ret = get_futex_value_locked(&curval, uaddr1);
-
- if (unlikely(ret)) {
- spin_unlock(&hb1->lock);
- if (hb1 != hb2)
- spin_unlock(&hb2->lock);
-
- /*
- * If we would have faulted, release mmap_sem, fault
- * it in and start all over again.
- */
- if (fshared)
- up_read(fshared);
-
- ret = get_user(curval, uaddr1);
-
- if (!ret)
- goto retry;
-
- return ret;
- }
- if (curval != *cmpval) {
- ret = -EAGAIN;
- goto out_unlock;
- }
- }
-
- head1 = &hb1->chain;
- plist_for_each_entry_safe(this, next, head1, list) {
- if (!match_futex (&this->key, &key1))
- continue;
- if (++ret <= nr_wake) {
- wake_futex(this);
- } else {
- /*
- * FIRST: get and set the pi_state
- */
- if (!pi_state2) {
- int s;
- /* do this only the first time we requeue someone */
- s = lookup_pi_state_for_requeue(uaddr2, hb2,
- &key2, &pi_state2);
- if (s) {
- ret = s;
- goto out_unlock;
- }
-
- lock2 = &pi_state2->pi_mutex;
- spin_lock(&lock2->wait_lock);
-
- /* Save the top waiter of the wait_list */
- if (rt_mutex_has_waiters(lock2))
- top_waiter = rt_mutex_top_waiter(lock2);
- } else
- atomic_inc(&pi_state2->refcount);
-
-
- this->pi_state = pi_state2;
-
- /*
- * SECOND: requeue futex_q to the correct hashbucket
- */
-
- /*
- * If key1 and key2 hash to the same bucket, no need to
- * requeue.
- */
- if (likely(head1 != &hb2->chain)) {
- plist_del(&this->list, &hb1->chain);
- plist_add(&this->list, &hb2->chain);
- this->lock_ptr = &hb2->lock;
-#ifdef CONFIG_DEBUG_PI_LIST
- this->list.plist.lock = &hb2->lock;
-#endif
- }
- this->key = key2;
- get_futex_key_refs(&key2);
- drop_count++;
-
-
- /*
- * THIRD: queue it to lock2
- */
- spin_lock_irq(&this->task->pi_lock);
- waiter = &this->waiter;
- waiter->task = this->task;
- waiter->lock = lock2;
- plist_node_init(&waiter->list_entry, this->task->prio);
- plist_node_init(&waiter->pi_list_entry, this->task->prio);
- plist_add(&waiter->list_entry, &lock2->wait_list);
- this->task->pi_blocked_on = waiter;
- spin_unlock_irq(&this->task->pi_lock);
-
- if (ret - nr_wake >= nr_requeue)
- break;
- }
- }
-
- /* If we've requeued some tasks and the top_waiter of the rt_mutex
- has changed, we must adjust the priority of the owner, if any */
- if (drop_count) {
- struct task_struct *owner = rt_mutex_owner(lock2);
- if (owner &&
- (top_waiter != (waiter = rt_mutex_top_waiter(lock2)))) {
- int chain_walk = 0;
-
- spin_lock_irq(&owner->pi_lock);
- if (top_waiter)
- plist_del(&top_waiter->pi_list_entry, &owner->pi_waiters);
- else
- /*
- * There was no waiters before the requeue,
- * the flag must be updated
- */
- mark_rt_mutex_waiters(lock2);
-
- plist_add(&waiter->pi_list_entry, &owner->pi_waiters);
- __rt_mutex_adjust_prio(owner);
- if (owner->pi_blocked_on) {
- chain_walk = 1;
- get_task_struct(owner);
- }
-
- spin_unlock_irq(&owner->pi_lock);
- spin_unlock(&lock2->wait_lock);
-
- if (chain_walk)
- rt_mutex_adjust_prio_chain(owner, 0, lock2, NULL,
- current);
- } else {
- /* No owner or the top_waiter does not change */
- mark_rt_mutex_waiters(lock2);
- spin_unlock(&lock2->wait_lock);
- }
- }
-
-out_unlock:
- spin_unlock(&hb1->lock);
- if (hb1 != hb2)
- spin_unlock(&hb2->lock);
-
- /* drop_futex_key_refs() must be called outside the spinlocks. */
- while (--drop_count >= 0)
- drop_futex_key_refs(&key1);
-
-out:
- if (fshared)
- up_read(fshared);
- return ret;
-}
-
/*
* Wake up all waiters hashed on the physical page that is mapped
* to this virtual address:
while (!ret) {
newval = (uval & FUTEX_OWNER_DIED) | newtid;
- newval |= (uval & FUTEX_WAITER_REQUEUED);
pagefault_disable();
curval = futex_atomic_cmpxchg_inatomic(uaddr,
struct futex_q q;
u32 uval;
int ret;
- struct hrtimer_sleeper t, *to = NULL;
+ struct hrtimer_sleeper t;
int rem = 0;
q.pi_state = NULL;
if (uval != val)
goto out_unlock_release_sem;
- /*
- * This rt_mutex_waiter structure is prepared here and will
- * be used only if this task is requeued from a normal futex to
- * a PI-futex with futex_requeue_pi.
- */
- debug_rt_mutex_init_waiter(&q.waiter);
- q.waiter.task = NULL;
-
/* Only actually queue if *uaddr contained val. */
__queue_me(&q, hb);
if (!abs_time)
schedule();
else {
- to = &t;
hrtimer_init(&t.timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
hrtimer_init_sleeper(&t, current);
t.timer.expires = *abs_time;
* we are the only user of it.
*/
- if (q.pi_state) {
- /*
- * We were woken but have been requeued on a PI-futex.
- * We have to complete the lock acquisition by taking
- * the rtmutex.
- */
-
- struct rt_mutex *lock = &q.pi_state->pi_mutex;
-
- spin_lock(&lock->wait_lock);
- if (unlikely(q.waiter.task)) {
- remove_waiter(lock, &q.waiter);
- }
- spin_unlock(&lock->wait_lock);
-
- if (rem)
- ret = -ETIMEDOUT;
- else
- ret = rt_mutex_timed_lock(lock, to, 1);
-
- if (fshared)
- down_read(fshared);
- spin_lock(q.lock_ptr);
-
- /*
- * Got the lock. We might not be the anticipated owner if we
- * did a lock-steal - fix up the PI-state in that case.
- */
- if (!ret && q.pi_state->owner != curr) {
- /*
- * We MUST play with the futex we were requeued on,
- * NOT the current futex.
- * We can retrieve it from the key of the pi_state
- */
- uaddr = q.pi_state->key.uaddr;
-
- ret = fixup_pi_state_owner(uaddr, &q, curr);
- } else {
- /*
- * Catch the rare case, where the lock was released
- * when we were on the way back before we locked
- * the hash bucket.
- */
- if (ret && q.pi_state->owner == curr) {
- if (rt_mutex_trylock(&q.pi_state->pi_mutex))
- ret = 0;
- }
- }
-
- /* Unqueue and drop the lock */
- unqueue_me_pi(&q);
- if (fshared)
- up_read(fshared);
-
- debug_rt_mutex_free_waiter(&q.waiter);
-
- return ret;
- }
-
- debug_rt_mutex_free_waiter(&q.waiter);
-
/* If we were woken (and unqueued), we succeeded, whatever. */
if (!unqueue_me(&q))
return 0;
}
-static void set_pi_futex_owner(struct futex_hash_bucket *hb,
- union futex_key *key, struct task_struct *p)
-{
- struct plist_head *head;
- struct futex_q *this, *next;
- struct futex_pi_state *pi_state = NULL;
- struct rt_mutex *lock;
-
- /* Search a waiter that should already exists */
-
- head = &hb->chain;
-
- plist_for_each_entry_safe(this, next, head, list) {
- if (match_futex (&this->key, key)) {
- pi_state = this->pi_state;
- break;
- }
- }
-
- BUG_ON(!pi_state);
-
- /* set p as pi_state's owner */
- lock = &pi_state->pi_mutex;
-
- spin_lock(&lock->wait_lock);
- spin_lock_irq(&p->pi_lock);
-
- list_add(&pi_state->list, &p->pi_state_list);
- pi_state->owner = p;
-
-
- /* set p as pi_mutex's owner */
- debug_rt_mutex_proxy_lock(lock, p);
- WARN_ON(rt_mutex_owner(lock));
- rt_mutex_set_owner(lock, p, 0);
- rt_mutex_deadlock_account_lock(lock, p);
-
- plist_add(&rt_mutex_top_waiter(lock)->pi_list_entry,
- &p->pi_waiters);
- __rt_mutex_adjust_prio(p);
-
- spin_unlock_irq(&p->pi_lock);
- spin_unlock(&lock->wait_lock);
-}
-
/*
* Userspace tried a 0 -> TID atomic transition of the futex value
* and failed. The kernel side here does the whole locking operation:
* situation and we return success to user space.
*/
if (unlikely((curval & FUTEX_TID_MASK) == current->pid)) {
- if (!(curval & FUTEX_WAITER_REQUEUED))
- ret = -EDEADLK;
+ ret = -EDEADLK;
goto out_unlock_release_sem;
}
/*
* There are two cases, where a futex might have no owner (the
- * owner TID is 0): OWNER_DIED or REQUEUE. We take over the
- * futex in this case. We also do an unconditional take over,
- * when the owner of the futex died.
+ * owner TID is 0): OWNER_DIED. We take over the futex in this
+ * case. We also do an unconditional take over, when the owner
+ * of the futex died.
*
* This is safe as we are protected by the hash bucket lock !
*/
if (unlikely(ownerdied || !(curval & FUTEX_TID_MASK))) {
- /* Keep the OWNER_DIED and REQUEUE bits */
+ /* Keep the OWNER_DIED bit */
newval = (curval & ~FUTEX_TID_MASK) | current->pid;
ownerdied = 0;
lock_taken = 1;
goto retry_locked;
/*
- * We took the lock due to requeue or owner died take over.
+ * We took the lock due to owner died take over.
*/
- if (unlikely(lock_taken)) {
- /* For requeue we need to fixup the pi_futex */
- if (curval & FUTEX_WAITER_REQUEUED)
- set_pi_futex_owner(hb, &q.key, curr);
+ if (unlikely(lock_taken))
goto out_unlock_release_sem;
- }
/*
* We dont have the lock. Look up the PI state (or create it if
* userspace.
*/
mval = (uval & FUTEX_WAITERS) | FUTEX_OWNER_DIED;
- /* Also keep the FUTEX_WAITER_REQUEUED flag if set */
- mval |= (uval & FUTEX_WAITER_REQUEUED);
nval = futex_atomic_cmpxchg_inatomic(uaddr, uval, mval);
if (nval == -EFAULT)
case FUTEX_TRYLOCK_PI:
ret = futex_lock_pi(uaddr, fshared, 0, timeout, 1);
break;
- case FUTEX_CMP_REQUEUE_PI:
- ret = futex_requeue_pi(uaddr, fshared, uaddr2, val, val2, &val3);
- break;
default:
ret = -ENOSYS;
}
/*
* requeue parameter in 'utime' if cmd == FUTEX_REQUEUE.
*/
- if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE
- || cmd == FUTEX_CMP_REQUEUE_PI)
+ if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE)
val2 = (u32) (unsigned long) utime;
return do_futex(uaddr, op, val, tp, uaddr2, val2, val3);
t = ktime_add(ktime_get(), t);
tp = &t;
}
- if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE
- || cmd == FUTEX_CMP_REQUEUE_PI)
+ if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE)
val2 = (int) (unsigned long) utime;
return do_futex(uaddr, op, val, tp, uaddr2, val2, val3);
/*
* Called from unshare. Unshare all the namespaces part of nsproxy.
- * On sucess, returns the new nsproxy and a reference to old nsproxy
- * to make sure it stays around.
+ * On success, returns the new nsproxy.
*/
int unshare_nsproxy_namespaces(unsigned long unshare_flags,
struct nsproxy **new_nsp, struct fs_struct *new_fs)
{
- struct nsproxy *old_ns = current->nsproxy;
int err = 0;
if (!(unshare_flags & (CLONE_NEWNS | CLONE_NEWUTS | CLONE_NEWIPC)))
if (!capable(CAP_SYS_ADMIN))
return -EPERM;
- get_nsproxy(old_ns);
-
*new_nsp = create_new_namespaces(unshare_flags, current,
new_fs ? new_fs : current->fs);
- if (IS_ERR(*new_nsp)) {
+ if (IS_ERR(*new_nsp))
err = PTR_ERR(*new_nsp);
- put_nsproxy(old_ns);
- }
return err;
}
* it should be restarted.
*/
if (timr->it.real.interval.tv64 != 0) {
+ ktime_t now = hrtimer_cb_get_time(timer);
+
+ /*
+ * FIXME: What we really want, is to stop this
+ * timer completely and restart it in case the
+ * SIG_IGN is removed. This is a non trivial
+ * change which involves sighand locking
+ * (sigh !), which we don't want to do late in
+ * the release cycle.
+ *
+ * For now we just let timers with an interval
+ * less than a jiffie expire every jiffie to
+ * avoid softirq starvation in case of SIG_IGN
+ * and a very small interval, which would put
+ * the timer right back on the softirq pending
+ * list. By moving now ahead of time we trick
+ * hrtimer_forward() to expire the timer
+ * later, while we still maintain the overrun
+ * accuracy, but have some inconsistency in
+ * the timer_gettime() case. This is at least
+ * better than a starved softirq. A more
+ * complex fix which solves also another related
+ * inconsistency is already in the pipeline.
+ */
+#ifdef CONFIG_HIGH_RES_TIMERS
+ {
+ ktime_t kj = ktime_set(0, NSEC_PER_SEC / HZ);
+
+ if (timr->it.real.interval.tv64 < kj.tv64)
+ now = ktime_add(now, kj);
+ }
+#endif
timr->it_overrun +=
- hrtimer_forward(timer,
- hrtimer_cb_get_time(timer),
+ hrtimer_forward(timer, now,
timr->it.real.interval);
ret = HRTIMER_RESTART;
++timr->it_requeue_pending;
* state.
*/
-void
+static void
rt_mutex_set_owner(struct rt_mutex *lock, struct task_struct *owner,
unsigned long mask)
{
clear_rt_mutex_waiters(lock);
}
+/*
+ * We can speed up the acquire/release, if the architecture
+ * supports cmpxchg and if there's no debugging state to be set up
+ */
+#if defined(__HAVE_ARCH_CMPXCHG) && !defined(CONFIG_DEBUG_RT_MUTEXES)
+# define rt_mutex_cmpxchg(l,c,n) (cmpxchg(&l->owner, c, n) == c)
+static inline void mark_rt_mutex_waiters(struct rt_mutex *lock)
+{
+ unsigned long owner, *p = (unsigned long *) &lock->owner;
+
+ do {
+ owner = *p;
+ } while (cmpxchg(p, owner, owner | RT_MUTEX_HAS_WAITERS) != owner);
+}
+#else
+# define rt_mutex_cmpxchg(l,c,n) (0)
+static inline void mark_rt_mutex_waiters(struct rt_mutex *lock)
+{
+ lock->owner = (struct task_struct *)
+ ((unsigned long)lock->owner | RT_MUTEX_HAS_WAITERS);
+}
+#endif
+
/*
* Calculate task priority from the waiter list priority
*
*
* This can be both boosting and unboosting. task->pi_lock must be held.
*/
-void __rt_mutex_adjust_prio(struct task_struct *task)
+static void __rt_mutex_adjust_prio(struct task_struct *task)
{
int prio = rt_mutex_getprio(task);
* Decreases task's usage by one - may thus free the task.
* Returns 0 or -EDEADLK.
*/
-int rt_mutex_adjust_prio_chain(struct task_struct *task,
- int deadlock_detect,
- struct rt_mutex *orig_lock,
- struct rt_mutex_waiter *orig_waiter,
- struct task_struct *top_task)
+static int rt_mutex_adjust_prio_chain(struct task_struct *task,
+ int deadlock_detect,
+ struct rt_mutex *orig_lock,
+ struct rt_mutex_waiter *orig_waiter,
+ struct task_struct *top_task)
{
struct rt_mutex *lock;
struct rt_mutex_waiter *waiter, *top_waiter = orig_waiter;
*
* Must be called with lock->wait_lock held
*/
-void remove_waiter(struct rt_mutex *lock,
- struct rt_mutex_waiter *waiter)
+static void remove_waiter(struct rt_mutex *lock,
+ struct rt_mutex_waiter *waiter)
{
int first = (waiter == rt_mutex_top_waiter(lock));
struct task_struct *owner = rt_mutex_owner(lock);
return (unsigned long)lock->owner & RT_MUTEX_OWNER_PENDING;
}
-/*
- * We can speed up the acquire/release, if the architecture
- * supports cmpxchg and if there's no debugging state to be set up
- */
-#if defined(__HAVE_ARCH_CMPXCHG) && !defined(CONFIG_DEBUG_RT_MUTEXES)
-# define rt_mutex_cmpxchg(l,c,n) (cmpxchg(&l->owner, c, n) == c)
-static inline void mark_rt_mutex_waiters(struct rt_mutex *lock)
-{
- unsigned long owner, *p = (unsigned long *) &lock->owner;
-
- do {
- owner = *p;
- } while (cmpxchg(p, owner, owner | RT_MUTEX_HAS_WAITERS) != owner);
-}
-#else
-# define rt_mutex_cmpxchg(l,c,n) (0)
-static inline void mark_rt_mutex_waiters(struct rt_mutex *lock)
-{
- lock->owner = (struct task_struct *)
- ((unsigned long)lock->owner | RT_MUTEX_HAS_WAITERS);
-}
-#endif
-
/*
* PI-futex support (proxy locking functions, etc.):
*/
struct task_struct *proxy_owner);
extern void rt_mutex_proxy_unlock(struct rt_mutex *lock,
struct task_struct *proxy_owner);
-
-extern void rt_mutex_set_owner(struct rt_mutex *lock, struct task_struct *owner,
- unsigned long mask);
-extern void __rt_mutex_adjust_prio(struct task_struct *task);
-extern int rt_mutex_adjust_prio_chain(struct task_struct *task,
- int deadlock_detect,
- struct rt_mutex *orig_lock,
- struct rt_mutex_waiter *orig_waiter,
- struct task_struct *top_task);
-extern void remove_waiter(struct rt_mutex *lock,
- struct rt_mutex_waiter *waiter);
#endif
{
unsigned long flags;
struct rq *rq;
- int preempted;
+ struct prio_array *array;
+ int running;
repeat:
+ /*
+ * We do the initial early heuristics without holding
+ * any task-queue locks at all. We'll only try to get
+ * the runqueue lock when things look like they will
+ * work out!
+ */
+ rq = task_rq(p);
+
+ /*
+ * If the task is actively running on another CPU
+ * still, just relax and busy-wait without holding
+ * any locks.
+ *
+ * NOTE! Since we don't hold any locks, it's not
+ * even sure that "rq" stays as the right runqueue!
+ * But we don't care, since "task_running()" will
+ * return false if the runqueue has changed and p
+ * is actually now running somewhere else!
+ */
+ while (task_running(rq, p))
+ cpu_relax();
+
+ /*
+ * Ok, time to look more closely! We need the rq
+ * lock now, to be *sure*. If we're wrong, we'll
+ * just go back and repeat.
+ */
rq = task_rq_lock(p, &flags);
- /* Must be off runqueue entirely, not preempted. */
- if (unlikely(p->array || task_running(rq, p))) {
- /* If it's preempted, we yield. It could be a while. */
- preempted = !task_running(rq, p);
- task_rq_unlock(rq, &flags);
+ running = task_running(rq, p);
+ array = p->array;
+ task_rq_unlock(rq, &flags);
+
+ /*
+ * Was it really running after all now that we
+ * checked with the proper locks actually held?
+ *
+ * Oops. Go back and try again..
+ */
+ if (unlikely(running)) {
cpu_relax();
- if (preempted)
- yield();
goto repeat;
}
- task_rq_unlock(rq, &flags);
+
+ /*
+ * It's not enough that it's not actively running,
+ * it must be off the runqueue _entirely_, and not
+ * preempted!
+ *
+ * So if it wa still runnable (but just not actively
+ * running right now), it's preempted, and we should
+ * yield - it could be a while.
+ */
+ if (unlikely(array)) {
+ yield();
+ goto repeat;
+ }
+
+ /*
+ * Ahh, all good. It wasn't running, and it wasn't
+ * runnable, which means that it will never become
+ * running in the future either. We're all done!
+ */
}
/***
unsigned long next_balance = jiffies + 60 * HZ;
for_each_domain(this_cpu, sd) {
- if (sd->flags & SD_BALANCE_NEWIDLE) {
+ unsigned long interval;
+
+ if (!(sd->flags & SD_LOAD_BALANCE))
+ continue;
+
+ if (sd->flags & SD_BALANCE_NEWIDLE)
/* If we've pulled tasks over stop searching: */
pulled_task = load_balance_newidle(this_cpu,
- this_rq, sd);
- if (time_after(next_balance,
- sd->last_balance + sd->balance_interval))
- next_balance = sd->last_balance
- + sd->balance_interval;
- if (pulled_task)
- break;
- }
+ this_rq, sd);
+
+ interval = msecs_to_jiffies(sd->balance_interval);
+ if (time_after(next_balance, sd->last_balance + interval))
+ next_balance = sd->last_balance + interval;
+ if (pulled_task)
+ break;
}
if (!pulled_task)
/*
void normalize_rt_tasks(void)
{
struct prio_array *array;
- struct task_struct *p;
+ struct task_struct *g, *p;
unsigned long flags;
struct rq *rq;
read_lock_irq(&tasklist_lock);
- for_each_process(p) {
+
+ do_each_thread(g, p) {
if (!rt_task(p))
continue;
__task_rq_unlock(rq);
spin_unlock_irqrestore(&p->pi_lock, flags);
- }
+ } while_each_thread(g, p);
+
read_unlock_irq(&tasklist_lock);
}
*/
int dequeue_signal(struct task_struct *tsk, sigset_t *mask, siginfo_t *info)
{
- int signr = __dequeue_signal(&tsk->pending, mask, info);
+ int signr = 0;
+
+ /* We only dequeue private signals from ourselves, we don't let
+ * signalfd steal them
+ */
+ if (tsk == current)
+ signr = __dequeue_signal(&tsk->pending, mask, info);
if (!signr) {
signr = __dequeue_signal(&tsk->signal->shared_pending,
mask, info);
* vma->vm_start/vm_end cannot change under us because the caller
* is required to hold the mmap_sem in read mode. We need the
* anon_vma lock to serialize against concurrent expand_stacks.
+ * Also guard against wrapping around to address 0.
*/
- address += 4 + PAGE_SIZE - 1;
- address &= PAGE_MASK;
+ if (address < PAGE_ALIGN(address+4))
+ address = PAGE_ALIGN(address+4);
+ else {
+ anon_vma_unlock(vma);
+ return -ENOMEM;
+ }
error = 0;
/* Somebody else might have raced and expanded it already */
n += sprintf(buf + n, " pid=%ld",
l->min_pid);
- if (num_online_cpus() > 1 && !cpus_empty(l->cpus)) {
+ if (num_online_cpus() > 1 && !cpus_empty(l->cpus) &&
+ n < PAGE_SIZE - 60) {
n += sprintf(buf + n, " cpus=");
n += cpulist_scnprintf(buf + n, PAGE_SIZE - n - 50,
l->cpus);
}
- if (num_online_nodes() > 1 && !nodes_empty(l->nodes)) {
+ if (num_online_nodes() > 1 && !nodes_empty(l->nodes) &&
+ n < PAGE_SIZE - 60) {
n += sprintf(buf + n, " nodes=");
n += nodelist_scnprintf(buf + n, PAGE_SIZE - n - 50,
l->nodes);
}
}
out:
+ local_irq_enable();
#ifdef CONFIG_NET_DMA
/*
* There may not be any more sk_buffs coming right now, so push
rcu_read_unlock();
}
#endif
- local_irq_enable();
return;
softnet_break:
n->tc_verd = CLR_TC_MUNGED(n->tc_verd);
C(iif);
#endif
- skb_copy_secmark(n, skb);
#endif
+ skb_copy_secmark(n, skb);
C(truesize);
atomic_set(&n->users, 1);
C(head);
st->stepped_offset += frag->size;
}
+ if (st->frag_data) {
+ kunmap_skb_frag(st->frag_data);
+ st->frag_data = NULL;
+ }
+
if (st->cur_skb->next) {
st->cur_skb = st->cur_skb->next;
st->frag_idx = 0;
struct ip_vs_seq out_seq; /* outgoing seq. struct */
};
+struct ip_vs_sync_thread_data {
+ struct completion *startup;
+ int state;
+};
+
#define IP_VS_SYNC_CONN_TIMEOUT (3*60*HZ)
#define SIMPLE_CONN_SIZE (sizeof(struct ip_vs_sync_conn))
#define FULL_CONN_SIZE \
mm_segment_t oldmm;
int state;
const char *name;
+ struct ip_vs_sync_thread_data *tinfo = startup;
/* increase the module use count */
ip_vs_use_count_inc();
add_wait_queue(&sync_wait, &wait);
set_sync_pid(state, current->pid);
- complete((struct completion *)startup);
+ complete(tinfo->startup);
+
+ /*
+ * once we call the completion queue above, we should
+ * null out that reference, since its allocated on the
+ * stack of the creating kernel thread
+ */
+ tinfo->startup = NULL;
/* processing master/backup loop here */
if (state == IP_VS_STATE_MASTER)
remove_wait_queue(&sync_wait, &wait);
/* thread exits */
+
+ /*
+ * If we weren't explicitly stopped, then we
+ * exited in error, and should undo our state
+ */
+ if ((!stop_master_sync) && (!stop_backup_sync))
+ ip_vs_sync_state -= tinfo->state;
+
set_sync_pid(state, 0);
IP_VS_INFO("sync thread stopped!\n");
set_stop_sync(state, 0);
wake_up(&stop_sync_wait);
+ /*
+ * we need to free the structure that was allocated
+ * for us in start_sync_thread
+ */
+ kfree(tinfo);
return 0;
}
{
DECLARE_COMPLETION_ONSTACK(startup);
pid_t pid;
+ struct ip_vs_sync_thread_data *tinfo;
if ((state == IP_VS_STATE_MASTER && sync_master_pid) ||
(state == IP_VS_STATE_BACKUP && sync_backup_pid))
return -EEXIST;
+ /*
+ * Note that tinfo will be freed in sync_thread on exit
+ */
+ tinfo = kmalloc(sizeof(struct ip_vs_sync_thread_data), GFP_KERNEL);
+ if (!tinfo)
+ return -ENOMEM;
+
IP_VS_DBG(7, "%s: pid %d\n", __FUNCTION__, current->pid);
IP_VS_DBG(7, "Each ip_vs_sync_conn entry need %Zd bytes\n",
sizeof(struct ip_vs_sync_conn));
ip_vs_backup_syncid = syncid;
}
+ tinfo->state = state;
+ tinfo->startup = &startup;
+
repeat:
- if ((pid = kernel_thread(fork_sync_thread, &startup, 0)) < 0) {
+ if ((pid = kernel_thread(fork_sync_thread, tinfo, 0)) < 0) {
IP_VS_ERR("could not create fork_sync_thread due to %d... "
"retrying.\n", pid);
msleep_interruptible(1000);
break;
}
used = recv_actor(desc, skb, offset, len);
- if (used <= len) {
+ if (used < 0) {
+ if (!copied)
+ copied = used;
+ break;
+ } else if (used <= len) {
seq += used;
copied += used;
offset += used;
tcp_rcv_space_adjust(sk);
/* Clean up data we have read: This will do ACK frames. */
- if (copied)
+ if (copied > 0)
tcp_cleanup_rbuf(sk, copied);
return copied;
}
pref = ra_msg->icmph.icmp6_router_pref;
/* 10b is handled as if it were 00b (medium) */
if (pref == ICMPV6_ROUTER_PREF_INVALID ||
- in6_dev->cnf.accept_ra_rtr_pref)
+ !in6_dev->cnf.accept_ra_rtr_pref)
pref = ICMPV6_ROUTER_PREF_MEDIUM;
#endif
return 0;
if (help->helper)
- /* we had a helper before ... */
- nf_ct_remove_expectations(ct);
+ return -EBUSY;
/* need to zero data of old helper */
memset(&help->help, 0, sizeof(help->help));
/* RTP info only in some SDP pkts */
if (memcmp(dptr, "INVITE", sizeof("INVITE") - 1) != 0 &&
+ memcmp(dptr, "UPDATE", sizeof("UPDATE") - 1) != 0 &&
+ memcmp(dptr, "SIP/2.0 180", sizeof("SIP/2.0 180") - 1) != 0 &&
+ memcmp(dptr, "SIP/2.0 183", sizeof("SIP/2.0 183") - 1) != 0 &&
memcmp(dptr, "SIP/2.0 200", sizeof("SIP/2.0 200") - 1) != 0) {
goto out;
}
goto efault;
sp->remain -= copy;
skb->mark += copy;
+ copied += copy;
len -= copy;
segment -= copy;
} while (segment > 0);
+success:
+ ret = copied;
out:
call->tx_pending = skb;
_leave(" = %d", ret);
maybe_error:
if (copied)
- ret = copied;
+ goto success;
goto out;
efault:
rep_nlh = nlmsg_hdr(rep_buf);
memcpy(rep_nlh, req_nlh, hdr_space);
rep_nlh->nlmsg_len = rep_buf->len;
- genlmsg_unicast(rep_buf, req_nlh->nlmsg_pid);
+ genlmsg_unicast(rep_buf, NETLINK_CB(skb).pid);
}
return 0;
x->type && x->type->get_mtu)
res = x->type->get_mtu(x, mtu);
else
- res = mtu;
+ res = mtu - x->props.header_len;
spin_unlock_bh(&x->lock);
return res;
}
my $P = $0;
$P =~ s@.*/@@g;
-my $V = '0.04';
+my $V = '0.06';
use Getopt::Long qw(:config no_auto_abbrev);
my $tree = 1;
my $chk_signoff = 1;
my $chk_patch = 1;
+my $tst_type = 0;
GetOptions(
'q|quiet' => \$quiet,
'tree!' => \$tree,
'signoff!' => \$chk_signoff,
'patch!' => \$chk_patch,
+ 'test-type!' => \$tst_type,
) or exit;
my $exit = 0;
}
sub ctx_block_get {
- my ($linenr, $remain, $outer) = @_;
+ my ($linenr, $remain, $outer, $open, $close) = @_;
my $line;
my $start = $linenr - 1;
my $blk = '';
$blk .= $rawlines[$line];
- @o = ($blk =~ /\{/g);
- @c = ($blk =~ /\}/g);
+ @o = ($blk =~ /$open/g);
+ @c = ($blk =~ /$close/g);
if (!$outer || (scalar(@o) - scalar(@c)) == 1) {
push(@res, $rawlines[$line]);
sub ctx_block_outer {
my ($linenr, $remain) = @_;
- return ctx_block_get($linenr, $remain, 1);
+ return ctx_block_get($linenr, $remain, 1, '\{', '\}');
}
sub ctx_block {
my ($linenr, $remain) = @_;
- return ctx_block_get($linenr, $remain, 0);
+ return ctx_block_get($linenr, $remain, 0, '\{', '\}');
+}
+sub ctx_statement {
+ my ($linenr, $remain) = @_;
+
+ return ctx_block_get($linenr, $remain, 0, '\(', '\)');
}
sub ctx_locate_comment {
my $in_comment = 0;
my $first_line = 0;
+ my $Ident = qr{[A-Za-z\d_]+};
+ my $Storage = qr{extern|static};
+ my $Sparse = qr{__user|__kernel|__force|__iomem};
+ my $NonptrType = qr{
+ \b
+ (?:const\s+)?
+ (?:unsigned\s+)?
+ (?:
+ void|
+ char|
+ short|
+ int|
+ long|
+ unsigned|
+ float|
+ double|
+ long\s+int|
+ long\s+long|
+ long\s+long\s+int|
+ struct\s+$Ident|
+ union\s+$Ident|
+ ${Ident}_t
+ )
+ (?:\s+$Sparse)*
+ \b
+ }x;
+ my $Type = qr{
+ \b$NonptrType\b
+ (?:\s*\*+\s*const|\s*\*+)?
+ }x;
+ my $Declare = qr{(?:$Storage\s+)?$Type};
+ my $Attribute = qr{__read_mostly|__init|__initdata};
+
foreach my $line (@lines) {
$linenr++;
+ my $rawline = $line;
+
#extract the filename as it passes
if ($line=~/^\+\+\+\s+(\S+)/) {
$realfile=$1;
# blank context lines so we need to count that too.
if ($line =~ /^( |\+|$)/) {
$realline++;
+ $realcnt-- if ($realcnt != 0);
# track any sort of multi-line comment. Obviously if
# the added text or context do not include the whole
# Track the previous line.
($prevline, $stashline) = ($stashline, $line);
($previndent, $stashindent) = ($stashindent, $indent);
+ } elsif ($realcnt == 1) {
+ $realcnt--;
}
- $realcnt-- if ($realcnt != 0);
#make up the handle for any error we report on this line
$here = "#$linenr: ";
my $hereprev = "$here\n$prevline\n$line\n\n";
#check the patch for a signoff:
- if ($line =~ /^\s*Signed-off-by:\s/) {
- $signoff++;
-
- } elsif ($line =~ /^\s*signed-off-by:/i) {
+ if ($line =~ /^\s*signed-off-by:/i) {
# This is a signoff, if ugly, so do not double report.
$signoff++;
if (!($line =~ /^\s*Signed-off-by:/)) {
- print "use Signed-off-by:\n";
+ print "Signed-off-by: is the preferred form\n";
print "$herecurr";
$clean = 0;
}
next if ($realfile !~ /\.(h|c|s|S|pl|sh)$/);
#trailing whitespace
- if ($line=~/\+.*\S\s+$/) {
+ if ($line =~ /^\+.*\S\s+$/ || $line =~ /^\+\s+$/) {
my $herevet = "$here\n" . cat_vet($line) . "\n\n";
print "trailing whitespace\n";
print "$herevet";
#
next if ($in_comment);
- # Remove comments from the line before processing.
+# Remove comments from the line before processing.
$line =~ s@/\*.*\*/@@g;
$line =~ s@/\*.*@@;
$line =~ s@.*\*/@@;
- #
- # Checks which may be anchored in the context.
- #
+# Standardise the strings and chars within the input to simplify matching.
+ $line = sanitise_line($line);
- # Check for switch () and associated case and default
- # statements should be at the same indent.
+#
+# Checks which may be anchored in the context.
+#
+
+# Check for switch () and associated case and default
+# statements should be at the same indent.
if ($line=~/\bswitch\s*\(.*\)/) {
my $err = '';
my $sep = '';
#ignore lines not being added
if ($line=~/^[^\+]/) {next;}
- #
- # Checks which are anchored on the added line.
- #
+# TEST: allow direct testing of the type matcher.
+ if ($tst_type && $line =~ /^.$Declare$/) {
+ print "TEST: is type $Declare\n";
+ print "$herecurr";
+ $clean = 0;
+ next;
+ }
+
+#
+# Checks which are anchored on the added line.
+#
+
+# check for malformed paths in #include statements (uses RAW line)
+ if ($rawline =~ m{^.#\s*include\s+[<"](.*)[">]}) {
+ my $path = $1;
+ if ($path =~ m{//}) {
+ print "malformed #include filename\n";
+ print "$herecurr";
+ $clean = 0;
+ }
+ # Sanitise this special form of string.
+ $path = 'X' x length($path);
+ $line =~ s{\<.*\>}{<$path>};
+ }
# no C99 // comments
if ($line =~ m{//}) {
# Remove C99 comments.
$line =~ s@//.*@@;
- # Standardise the strings and chars within the input
- # to simplify matching.
- $line = sanitise_line($line);
-
#EXPORT_SYMBOL should immediately follow its function closing }.
- if (($line =~ /EXPORT_SYMBOL.*\(.*\)/) ||
- ($line =~ /EXPORT_UNUSED_SYMBOL.*\(.*\)/)) {
+ if (($line =~ /EXPORT_SYMBOL.*\((.*)\)/) ||
+ ($line =~ /EXPORT_UNUSED_SYMBOL.*\((.*)\)/)) {
+ my $name = $1;
if (($prevline !~ /^}/) &&
($prevline !~ /^\+}/) &&
- ($prevline !~ /^ }/)) {
- print "EXPORT_SYMBOL(func); should immediately follow its function\n";
+ ($prevline !~ /^ }/) &&
+ ($prevline !~ /\s$name(?:\s+$Attribute)?\s*(?:;|=)/)) {
+ print "EXPORT_SYMBOL(foo); should immediately follow its function/variable\n";
print "$herecurr";
$clean = 0;
}
}
- # check for static initialisers.
+# check for static initialisers.
if ($line=~/\s*static\s.*=\s+(0|NULL);/) {
print "do not initialise statics to 0 or NULL\n";
print "$herecurr";
$clean = 0;
}
- # check for new typedefs.
- if ($line=~/\s*typedef\s/) {
+# check for new typedefs, only function parameters and sparse annotations
+# make sense.
+ if ($line =~ /\btypedef\s/ &&
+ $line !~ /\btypedef\s+$Type\s+\(\s*$Ident\s*\)\s*\(/ &&
+ $line !~ /\b__bitwise(?:__|)\b/) {
print "do not add new typedefs\n";
print "$herecurr";
$clean = 0;
}
# * goes on variable not on type
- my $type = '(?:char|short|int|long|unsigned|float|double|' .
- 'struct\s+[A-Za-z\d_]+|' .
- 'union\s+[A-Za-z\d_]+)';
-
- if ($line =~ m{[A-Za-z\d_]+(\*+) [A-Za-z\d_]+}) {
- print "\"foo$1 bar\" should be \"foo $1bar\"\n";
+ if ($line =~ m{\($NonptrType(\*+)(?:\s+const)?\)}) {
+ print "\"(foo$1)\" should be \"(foo $1)\"\n";
print "$herecurr";
$clean = 0;
- }
- if ($line =~ m{$type (\*) [A-Za-z\d_]+} ||
- $line =~ m{[A-Za-z\d_]+ (\*\*+) [A-Za-z\d_]+}) {
- print "\"foo $1 bar\" should be \"foo $1bar\"\n";
+
+ } elsif ($line =~ m{\($NonptrType\s+(\*+)(?!\s+const)\s+\)}) {
+ print "\"(foo $1 )\" should be \"(foo $1)\"\n";
print "$herecurr";
$clean = 0;
- }
- if ($line =~ m{\([A-Za-z\d_\s]+[A-Za-z\d_](\*+)\)}) {
- print "\"(foo$1)\" should be \"(foo $1)\"\n";
+
+ } elsif ($line =~ m{$NonptrType(\*+)(?:\s+const)?\s+[A-Za-z\d_]+}) {
+ print "\"foo$1 bar\" should be \"foo $1bar\"\n";
print "$herecurr";
$clean = 0;
- }
- if ($line =~ m{\([A-Za-z\d_\s]+[A-Za-z\d_]\s+(\*+)\s+\)}) {
- print "\"(foo $1 )\" should be \"(foo $1)\"\n";
+
+ } elsif ($line =~ m{$NonptrType\s+(\*+)(?!\s+const)\s+[A-Za-z\d_]+}) {
+ print "\"foo $1 bar\" should be \"foo $1bar\"\n";
print "$herecurr";
$clean = 0;
}
}
}
-#function brace can't be on same line, except for #defines of do while, or if closed on same line
- if (($line=~/[A-Za-z\d_]+\**\s+\**[A-Za-z\d_]+\(.*\).* {/) and
+# function brace can't be on same line, except for #defines of do while,
+# or if closed on same line
+ if (($line=~/$Type\s*[A-Za-z\d_]+\(.*\).* {/) and
!($line=~/\#define.*do\s{/) and !($line=~/}/)) {
print "braces following function declarations go on the next line\n";
print "$herecurr";
$clean = 0;
}
+
+# Check operator spacing.
# Note we expand the line with the leading + as the real
# line will be displayed with the leading + and the tabs
# will therefore also expand that way.
$opline = expand_tabs($opline);
$opline =~ s/^./ /;
if (!($line=~/\#\s*include/)) {
- # Check operator spacing.
my @elements = split(/(<<=|>>=|<=|>=|==|!=|\+=|-=|\*=|\/=|%=|\^=|\|=|&=|->|<<|>>|<|>|=|!|~|&&|\|\||,|\^|\+\+|--|;|&|\||\+|-|\*|\/\/|\/)/, $opline);
my $off = 0;
for (my $n = 0; $n < $#elements; $n += 2) {
# Pick up the preceeding and succeeding characters.
my $ca = substr($opline, $off - 1, 1);
my $cc = '';
- if (length($opline) > ($off + length($elements[$n]))) {
- $cc = substr($opline, $off + 1 + length($elements[$n]), 1);
+ if (length($opline) >= ($off + length($elements[$n + 1]))) {
+ $cc = substr($opline, $off + length($elements[$n + 1]));
}
my $ctx = "${a}x${c}";
##print "<$s1:$op:$s2> <$elements[$n]:$elements[$n + 1]:$elements[$n + 2]>\n";
- # We need ; as an operator. // is a comment.
- if ($op eq ';' or $op eq '//') {
+ # ; should have either the end of line or a space or \ after it
+ if ($op eq ';') {
+ if ($ctx !~ /.x[WE]/ && $cc !~ /^\\/) {
+ print "need space after that '$op' $at\n";
+ print "$hereptr";
+ $clean = 0;
+ }
+
+ # // is a comment
+ } elsif ($op eq '//') {
# -> should have no spaces
} elsif ($op eq '->') {
# , must have a space on the right.
} elsif ($op eq ',') {
- if ($ctx !~ /.xW|.xE/) {
+ if ($ctx !~ /.xW|.xE/ && $cc !~ /^}/) {
print "need space after that '$op' $at\n";
print "$hereptr";
$clean = 0;
# unary ++ and unary -- are allowed no space on one side.
} elsif ($op eq '++' or $op eq '--') {
- if ($ctx !~ /[WOB]x[^W]|[^W]x[WOB]/) {
+ if ($ctx !~ /[WOB]x[^W]/ && $ctx !~ /[^W]x[WOBE]/) {
print "need space one side of that '$op' $at\n";
print "$hereptr";
$clean = 0;
}
+ if ($ctx =~ /Wx./ && $cc =~ /^;/) {
+ print "no space before that '$op' $at\n";
+ print "$hereptr";
+ $clean = 0;
+ }
# & is both unary and binary
# unary:
#
} elsif ($op eq '*') {
if ($ca eq '*') {
- if ($cc =~ /\s/) {
+ if ($cc =~ /^\s(?!\s*const)/) {
print "no space after that '$op' $at\n";
print "$hereptr";
$clean = 0;
}
- } elsif ($ctx !~ /VxV|[EW]x[WE]|[EWB]x[VO]|OxV|WxB/) {
+ } elsif ($ctx !~ /VxV|[EW]x[WE]|[EWB]x[VO]|OxV|WxB|BxB/) {
print "need space before that '$op' $at\n";
print "$hereptr";
$clean = 0;
}
# Check for illegal assignment in if conditional.
- if ($line=~/\b(if|while)\s*\(.*[^<>!=]=[^=].*\)/) {
+ if ($line=~/\bif\s*\(.*[^<>!=]=[^=].*\)/) {
#next if ($line=~/\".*\Q$op\E.*\"/ or $line=~/\'\Q$op\E\'/);
- print "do not use assignment in condition\n";
+ print "do not use assignment in if condition\n";
print "$herecurr";
$clean = 0;
}
$clean = 0;
}
-#warn if <asm/foo.h> is #included and <linux/foo.h> is available.
- if ($tree && $line =~ qr|\s*\#\s*include\s*\<asm\/(.*)\.h\>|) {
+#warn if <asm/foo.h> is #included and <linux/foo.h> is available (uses RAW line)
+ if ($tree && $rawline =~ m{^.\#\s*include\s*\<asm\/(.*)\.h\>}) {
my $checkfile = "include/linux/$1.h";
if (-f $checkfile) {
print "Use #include <linux/$1.h> instead of <asm/$1.h>\n";
}
}
-#if/while/etc brace do not go on next line, unless #defining a do while loop, or if that brace on the next line is for something else
- if ($prevline=~/\b(if|while|for|switch)\s*\(/) {
+# if/while/etc brace do not go on next line, unless defining a do while loop,
+# or if that brace on the next line is for something else
+ if ($prevline=~/\b(?:(if|while|for|switch)\s*\(|do\b|else\b)/) {
my @opened = $prevline=~/\(/g;
my @closed = $prevline=~/\)/g;
my $nr_line = $linenr;
@closed = $prevline=~/\)/g;
}
- if (($prevline=~/\b(if|while|for|switch)\s*\(.*\)\s*$/) and ($next_line=~/{/) and
- !($next_line=~/\b(if|while|for)/) and !($next_line=~/\#define.*do.*while/)) {
+ if (($prevline=~/\b(?:(if|while|for|switch)\s*\(.*\)|do|else)\s*$/) and ($next_line=~/{/) and
+ !($next_line=~/\b(?:if|while|for|switch|do|else)\b/) and !($next_line=~/\#define.*do.*while/)) {
print "That { should be on the previous line\n";
print "$here\n$display_segment\n$next_line\n\n";
$clean = 0;
}
}
-#multiline macros should be enclosed in a do while loop
- if (($prevline=~/\#define.*\\/) and !($prevline=~/do\s+{/) and
- !($prevline=~/\(\{/) and ($line=~/;\s*\\/) and
- !($line=~/do.*{/) and !($line=~/\(\{/)) {
- print "Macros with multiple statements should be enclosed in a do - while loop\n";
- print "$hereprev";
+# if and else should not have general statements after it
+ if ($line =~ /^.\s*(?:}\s*)?else\b(.*)/ &&
+ $1 !~ /^\s*(?:\sif|{|$)/) {
+ print "trailing statements should be on next line\n";
+ print "$herecurr";
$clean = 0;
}
-# don't include deprecated include files
+# multi-statement macros should be enclosed in a do while loop, grab the
+# first statement and ensure its the whole macro if its not enclosed
+# in a known goot container
+ if (($prevline=~/\#define.*\\/) and
+ !($prevline=~/do\s+{/) and !($prevline=~/\(\{/) and
+ !($line=~/do.*{/) and !($line=~/\(\{/) and
+ !($line=~/^.\s*$Declare\s/)) {
+ # Grab the first statement, if that is the entire macro
+ # its ok. This may start either on the #define line
+ # or the one below.
+ my $ln = $linenr;
+ my $cnt = $realcnt;
+
+ # If the macro starts on the define line start there.
+ if ($prevline !~ m{^.#\s*define\s*$Ident(?:\([^\)]*\))?\s*\\\s*$}) {
+ $ln--;
+ $cnt++;
+ }
+ my $ctx = join('', ctx_statement($ln, $cnt));
+
+ if ($ctx =~ /\\$/) {
+ if ($ctx =~ /;/) {
+ print "Macros with multiple statements should be enclosed in a do - while loop\n";
+ } else {
+ print "Macros with complex values should be enclosed in parenthesis\n";
+ }
+ print "$hereprev";
+ $clean = 0;
+ }
+ }
+
+# don't include deprecated include files (uses RAW line)
for my $inc (@dep_includes) {
- if ($line =~ m@\#\s*include\s*\<$inc>@) {
+ if ($rawline =~ m@\#\s*include\s*\<$inc>@) {
print "Don't use <$inc>: see Documentation/feature-removal-schedule.txt\n";
print "$herecurr";
$clean = 0;
print "$herecurr";
$clean = 0;
}
+
+ if ($line =~ /$Type\s+(?:inline|__always_inline)\b/ ||
+ $line =~ /\b(?:inline|always_inline)\s+$Storage/) {
+ print "inline keyword should sit between storage class and type\n";
+ print "$herecurr";
+ $clean = 0;
+ }
}
if ($chk_patch && !$is_patch) {
out_le32(&chip->awacs->control, in_le32(&chip->awacs->control) & 0xfff);
}
- snd_pmac_sound_feature(chip, 0);
+ if (chip->node)
+ snd_pmac_sound_feature(chip, 0);
/* clean up mixer if any */
if (chip->mixer_free)
}
if (! sound) {
of_node_put(chip->node);
+ chip->node = NULL;
return -ENODEV;
}
prop = of_get_property(sound, "sub-frame", NULL);
printk(KERN_INFO "snd-powermac no longer handles any "
"machines with a layout-id property "
"in the device-tree, use snd-aoa.\n");
+ of_node_put(sound);
of_node_put(chip->node);
+ chip->node = NULL;
return -ENODEV;
}
/* This should be verified on older screamers */
return 0;
__error:
- if (chip->pdev)
- pci_dev_put(chip->pdev);
snd_pmac_free(chip);
return err;
}
projects / linux-2.6-omap-h63xx.git / commitdiff