* published by the Free Software Foundation.
*/
+#include <linux/platform_device.h>
+
+#include <linux/i2c/tps65010.h>
+
#include <mach/mmc.h>
#include <mach/gpio.h>
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+
+static int mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+ if (power_on)
+ gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 1);
+ else
+ gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0);
+
+ return 0;
+}
+
+static int mmc_late_init(struct device *dev)
+{
+ int ret;
+
+ ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power");
+ if (ret < 0)
+ return ret;
+
+ gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0);
+
+ return ret;
+}
+
+static void mmc_shutdown(struct device *dev)
+{
+ gpio_free(H2_TPS_GPIO_MMC_PWR_EN);
+}
+
+/*
+ * H2 could use the following functions tested:
+ * - mmc_get_cover_state that uses OMAP_MPUIO(1)
+ * - mmc_get_wp that uses OMAP_MPUIO(3)
+ */
+static struct omap_mmc_platform_data mmc1_data = {
+ .nr_slots = 1,
+ .init = mmc_late_init,
+ .shutdown = mmc_shutdown,
+ .dma_mask = 0xffffffff,
+ .slots[0] = {
+ .set_power = mmc_set_power,
+ .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .name = "mmcblk",
+ },
+};
+
+static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
+
void __init h2_mmc_init(void)
{
+ mmc_data[0] = &mmc1_data;
+ omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
}
-void h2_mmc_slot_cover_handler(void *arg, int state)
+#else
+
+void __init h2_mmc_init(void)
{
}
+
+#endif
}
}
+static int tps_setup(struct i2c_client *client, void *context)
+{
+ tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
+ TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
+
+ return 0;
+}
+
+static struct tps65010_board tps_board = {
+ .base = H2_TPS_GPIO_BASE,
+ .outmask = 0x0f,
+ .setup = tps_setup,
+};
+
static struct i2c_board_info __initdata h2_i2c_board_info[] = {
{
I2C_BOARD_INFO("tps65010", 0x48),
.irq = OMAP_GPIO_IRQ(58),
+ .platform_data = &tps_board,
}, {
I2C_BOARD_INFO("isp1301_omap", 0x2d),
.irq = OMAP_GPIO_IRQ(2),
* published by the Free Software Foundation.
*/
+#include <linux/platform_device.h>
+
+#include <linux/i2c/tps65010.h>
+
#include <mach/mmc.h>
#include <mach/gpio.h>
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+
+static int mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+ if (power_on)
+ gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 1);
+ else
+ gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0);
+
+ return 0;
+}
+
+/*
+ * H3 could use the following functions tested:
+ * - mmc_get_cover_state that uses OMAP_MPUIO(1)
+ * - mmc_get_wp that maybe uses OMAP_MPUIO(3)
+ */
+static struct omap_mmc_platform_data mmc1_data = {
+ .nr_slots = 1,
+ .dma_mask = 0xffffffff,
+ .slots[0] = {
+ .set_power = mmc_set_power,
+ .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .name = "mmcblk",
+ },
+};
+
+static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
+
void __init h3_mmc_init(void)
{
+ int ret;
+
+ ret = gpio_request(H3_TPS_GPIO_MMC_PWR_EN, "MMC power");
+ if (ret < 0)
+ return;
+ gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0);
+
+ mmc_data[0] = &mmc1_data;
+ omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC);
}
-void h3_mmc_slot_cover_handler(void *arg, int state)
+#else
+
+void __init h3_mmc_init(void)
{
}
+
+#endif
#include <mach/common.h>
#include <mach/mcbsp.h>
#include <mach/omap-alsa.h>
+#include <mach/mmc.h>
static int innovator_keymap[] = {
KEY(0, 0, KEY_F1),
};
#endif
-static struct omap_mmc_config innovator_mmc_config __initdata = {
- .mmc [0] = {
- .enabled = 1,
- .wire4 = 1,
- .wp_pin = OMAP_MPUIO(3),
- .power_pin = -1, /* FPGA F3 UIO42 */
- .switch_pin = -1, /* FPGA F4 UIO43 */
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+
+static int mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+ if (power_on)
+ fpga_write(fpga_read(OMAP1510_FPGA_POWER) | (1 << 3),
+ OMAP1510_FPGA_POWER);
+ else
+ fpga_write(fpga_read(OMAP1510_FPGA_POWER) & ~(1 << 3),
+ OMAP1510_FPGA_POWER);
+
+ return 0;
+}
+
+/*
+ * Innovator could use the following functions tested:
+ * - mmc_get_wp that uses OMAP_MPUIO(3)
+ * - mmc_get_cover_state that uses FPGA F4 UIO43
+ */
+static struct omap_mmc_platform_data mmc1_data = {
+ .nr_slots = 1,
+ .slots[0] = {
+ .set_power = mmc_set_power,
+ .wire4 = 1,
+ .name = "mmcblk",
},
};
+static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC];
+
+void __init innovator_mmc_init(void)
+{
+ mmc_data[0] = &mmc1_data;
+ omap1_init_mmc(mmc_data, OMAP15XX_NR_MMC);
+}
+
+#else
+static inline void innovator_mmc_init(void)
+{
+}
+#endif
+
static struct omap_uart_config innovator_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel innovator_config[] = {
{ OMAP_TAG_USB, NULL },
{ OMAP_TAG_LCD, NULL },
- { OMAP_TAG_MMC, &innovator_mmc_config },
{ OMAP_TAG_UART, &innovator_uart_config },
};
omap_board_config_size = ARRAY_SIZE(innovator_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
+ innovator_mmc_init();
}
static void __init innovator_map_io(void)
#include <mach/aic23.h>
#include <mach/omapfb.h>
#include <mach/lcd_mipid.h>
+#include <mach/mmc.h>
#define ADS7846_PENDOWN_GPIO 15
.pins[0] = 6,
};
-static struct omap_mmc_config nokia770_mmc_config __initdata = {
- .mmc[0] = {
- .enabled = 0,
- .wire4 = 0,
- .wp_pin = -1,
- .power_pin = -1,
- .switch_pin = -1,
- },
- .mmc[1] = {
- .enabled = 0,
- .wire4 = 0,
- .wp_pin = -1,
- .power_pin = -1,
- .switch_pin = -1,
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+
+#define NOKIA770_GPIO_MMC_POWER 41
+#define NOKIA770_GPIO_MMC_SWITCH 23
+
+static int nokia770_mmc_set_power(struct device *dev, int slot, int power_on,
+ int vdd)
+{
+ if (power_on)
+ gpio_set_value(NOKIA770_GPIO_MMC_POWER, 1);
+ else
+ gpio_set_value(NOKIA770_GPIO_MMC_POWER, 0);
+
+ return 0;
+}
+
+static int nokia770_mmc_get_cover_state(struct device *dev, int slot)
+{
+ return gpio_get_value(NOKIA770_GPIO_MMC_SWITCH);
+}
+
+static struct omap_mmc_platform_data nokia770_mmc2_data = {
+ .nr_slots = 1,
+ .dma_mask = 0xffffffff,
+ .slots[0] = {
+ .set_power = nokia770_mmc_set_power,
+ .get_cover_state = nokia770_mmc_get_cover_state,
+ .name = "mmcblk",
},
};
+static struct omap_mmc_platform_data *nokia770_mmc_data[OMAP16XX_NR_MMC];
+
+static void __init nokia770_mmc_init(void)
+{
+ int ret;
+
+ ret = gpio_request(NOKIA770_GPIO_MMC_POWER, "MMC power");
+ if (ret < 0)
+ return;
+ gpio_direction_output(NOKIA770_GPIO_MMC_POWER, 0);
+
+ ret = gpio_request(NOKIA770_GPIO_MMC_SWITCH, "MMC cover");
+ if (ret < 0) {
+ gpio_free(NOKIA770_GPIO_MMC_POWER);
+ return;
+ }
+ gpio_direction_input(NOKIA770_GPIO_MMC_SWITCH);
+
+ /* Only the second MMC controller is used */
+ nokia770_mmc_data[1] = &nokia770_mmc2_data;
+ omap1_init_mmc(nokia770_mmc_data, OMAP16XX_NR_MMC);
+}
+
+#else
+static inline void nokia770_mmc_init(void)
+{
+}
+#endif
+
static struct omap_board_config_kernel nokia770_config[] __initdata = {
{ OMAP_TAG_USB, NULL },
- { OMAP_TAG_MMC, &nokia770_mmc_config },
};
#if defined(CONFIG_OMAP_DSP)
omap_dsp_init();
ads7846_dev_init();
mipid_dev_init();
+ nokia770_mmc_init();
}
static void __init omap_nokia770_map_io(void)
* published by the Free Software Foundation.
*/
+#include <linux/platform_device.h>
+
#include <mach/hardware.h>
#include <mach/mmc.h>
#include <mach/gpio.h>
-#ifdef CONFIG_MMC_OMAP
-static int slot_cover_open;
-static struct device *mmc_device;
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-static int sx1_mmc_set_power(struct device *dev, int slot, int power_on,
+static int mmc_set_power(struct device *dev, int slot, int power_on,
int vdd)
{
int err;
u8 dat = 0;
-#ifdef CONFIG_MMC_DEBUG
- dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
- power_on ? "on" : "off", vdd);
-#endif
-
- if (slot != 0) {
- dev_err(dev, "No such slot %d\n", slot + 1);
- return -ENODEV;
- }
-
err = sx1_i2c_read_byte(SOFIA_I2C_ADDR, SOFIA_POWER1_REG, &dat);
if (err < 0)
return err;
return sx1_i2c_write_byte(SOFIA_I2C_ADDR, SOFIA_POWER1_REG, dat);
}
-static struct omap_mmc_platform_data sx1_mmc_data = {
+/* Cover switch is at OMAP_MPUIO(3) */
+static struct omap_mmc_platform_data mmc1_data = {
.nr_slots = 1,
.slots[0] = {
- .set_power = sx1_mmc_set_power,
+ .set_power = mmc_set_power,
.ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 |
MMC_VDD_32_33 | MMC_VDD_33_34,
.name = "mmcblk",
},
};
+static struct omap_mmc_platform_data *mmc_data[OMAP15XX_NR_MMC];
+
void __init sx1_mmc_init(void)
{
- omap_set_mmc_info(1, &sx1_mmc_data);
+ mmc_data[0] = &mmc1_data;
+ omap1_init_mmc(mmc_data, OMAP15XX_NR_MMC);
}
#else
{
}
-void sx1_mmc_slot_cover_handler(void *arg, int state)
-{
-}
#endif
static struct clk mmc1_ck = {
.name = "mmc_ck",
- .id = 1,
/* Functional clock is direct from ULPD, interface clock is ARMPER */
.parent = &armper_ck.clk,
.rate = 48000000,
static struct clk mmc2_ck = {
.name = "mmc_ck",
- .id = 2,
+ .id = 1,
/* Functional clock is direct from ULPD, interface clock is ARMPER */
.parent = &armper_ck.clk,
.rate = 48000000,
#include <mach/board.h>
#include <mach/mux.h>
#include <mach/gpio.h>
+#include <mach/mmc.h>
/*-------------------------------------------------------------------------*/
static inline void omap_init_mbox(void) { }
#endif
+/*-------------------------------------------------------------------------*/
+
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
+
+static inline void omap1_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
+ int controller_nr)
+{
+ if (controller_nr == 0) {
+ omap_cfg_reg(MMC_CMD);
+ omap_cfg_reg(MMC_CLK);
+ omap_cfg_reg(MMC_DAT0);
+ if (cpu_is_omap1710()) {
+ omap_cfg_reg(M15_1710_MMC_CLKI);
+ omap_cfg_reg(P19_1710_MMC_CMDDIR);
+ omap_cfg_reg(P20_1710_MMC_DATDIR0);
+ }
+ if (mmc_controller->slots[0].wire4) {
+ omap_cfg_reg(MMC_DAT1);
+ /* NOTE: DAT2 can be on W10 (here) or M15 */
+ if (!mmc_controller->slots[0].nomux)
+ omap_cfg_reg(MMC_DAT2);
+ omap_cfg_reg(MMC_DAT3);
+ }
+ }
+
+ /* Block 2 is on newer chips, and has many pinout options */
+ if (cpu_is_omap16xx() && controller_nr == 1) {
+ if (!mmc_controller->slots[1].nomux) {
+ omap_cfg_reg(Y8_1610_MMC2_CMD);
+ omap_cfg_reg(Y10_1610_MMC2_CLK);
+ omap_cfg_reg(R18_1610_MMC2_CLKIN);
+ omap_cfg_reg(W8_1610_MMC2_DAT0);
+ if (mmc_controller->slots[1].wire4) {
+ omap_cfg_reg(V8_1610_MMC2_DAT1);
+ omap_cfg_reg(W15_1610_MMC2_DAT2);
+ omap_cfg_reg(R10_1610_MMC2_DAT3);
+ }
+
+ /* These are needed for the level shifter */
+ omap_cfg_reg(V9_1610_MMC2_CMDDIR);
+ omap_cfg_reg(V5_1610_MMC2_DATDIR0);
+ omap_cfg_reg(W19_1610_MMC2_DATDIR1);
+ }
+
+ /* Feedback clock must be set on OMAP-1710 MMC2 */
+ if (cpu_is_omap1710())
+ omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
+ MOD_CONF_CTRL_1);
+ }
+}
+
+void __init omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers)
+{
+ int i;
+
+ for (i = 0; i < nr_controllers; i++) {
+ unsigned long base, size;
+ unsigned int irq = 0;
+
+ if (!mmc_data[i])
+ continue;
+
+ omap1_mmc_mux(mmc_data[i], i);
+
+ switch (i) {
+ case 0:
+ base = OMAP1_MMC1_BASE;
+ irq = INT_MMC;
+ break;
+ case 1:
+ if (!cpu_is_omap16xx())
+ return;
+ base = OMAP1_MMC2_BASE;
+ irq = INT_1610_MMC2;
+ break;
+ default:
+ continue;
+ }
+ size = OMAP1_MMC_SIZE;
+
+ omap_mmc_add(i, base, size, irq, mmc_data[i]);
+ };
+}
+
+#endif
+
+/*-------------------------------------------------------------------------*/
+
#if defined(CONFIG_OMAP_STI)
#define OMAP1_STI_BASE 0xfffea000
static struct clk mmchs1_ick = {
.name = "mmchs_ick",
- .id = 1,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP243X,
.clkdm_name = "core_l4_clkdm",
static struct clk mmchs1_fck = {
.name = "mmchs_fck",
- .id = 1,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP243X,
.clkdm_name = "core_l3_clkdm",
static struct clk mmchs2_ick = {
.name = "mmchs_ick",
- .id = 2,
+ .id = 1,
.parent = &l4_ck,
.flags = CLOCK_IN_OMAP243X,
.clkdm_name = "core_l4_clkdm",
static struct clk mmchs2_fck = {
.name = "mmchs_fck",
- .id = 2,
+ .id = 1,
.parent = &func_96m_ck,
.flags = CLOCK_IN_OMAP243X,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2),
static struct clk mmchsdb1_fck = {
.name = "mmchsdb_fck",
- .id = 1,
.parent = &func_32k_ck,
.flags = CLOCK_IN_OMAP243X,
.clkdm_name = "core_l4_clkdm",
static struct clk mmchsdb2_fck = {
.name = "mmchsdb_fck",
- .id = 2,
+ .id = 1,
.parent = &func_32k_ck,
.flags = CLOCK_IN_OMAP243X,
.clkdm_name = "core_l4_clkdm",
static struct clk mmchs3_fck = {
.name = "mmchs_fck",
- .id = 3,
+ .id = 2,
.parent = &core_96m_fck,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
.enable_bit = OMAP3430ES2_EN_MMC3_SHIFT,
static struct clk mmchs2_fck = {
.name = "mmchs_fck",
- .id = 2,
+ .id = 1,
.parent = &core_96m_fck,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
.enable_bit = OMAP3430_EN_MMC2_SHIFT,
static struct clk mmchs1_fck = {
.name = "mmchs_fck",
- .id = 1,
.parent = &core_96m_fck,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
.enable_bit = OMAP3430_EN_MMC1_SHIFT,
static struct clk mmchs3_ick = {
.name = "mmchs_ick",
- .id = 3,
+ .id = 2,
.parent = &core_l4_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430ES2_EN_MMC3_SHIFT,
static struct clk mmchs2_ick = {
.name = "mmchs_ick",
- .id = 2,
+ .id = 1,
.parent = &core_l4_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_MMC2_SHIFT,
static struct clk mmchs1_ick = {
.name = "mmchs_ick",
- .id = 1,
.parent = &core_l4_ick,
.enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
.enable_bit = OMAP3430_EN_MMC1_SHIFT,
#include <mach/mux.h>
#include <mach/gpio.h>
#include <mach/eac.h>
+#include <mach/mmc.h>
#if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE)
#define OMAP2_MBOX_BASE IO_ADDRESS(OMAP24XX_MAILBOX_BASE)
static inline void omap_init_sha1_md5(void) { }
#endif
+/*-------------------------------------------------------------------------*/
+
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+ defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+
+static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
+ int controller_nr)
+{
+ if (cpu_is_omap2420() && controller_nr == 0) {
+ omap_cfg_reg(H18_24XX_MMC_CMD);
+ omap_cfg_reg(H15_24XX_MMC_CLKI);
+ omap_cfg_reg(G19_24XX_MMC_CLKO);
+ omap_cfg_reg(F20_24XX_MMC_DAT0);
+ omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
+ omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
+ if (mmc_controller->slots[0].wire4) {
+ omap_cfg_reg(H14_24XX_MMC_DAT1);
+ omap_cfg_reg(E19_24XX_MMC_DAT2);
+ omap_cfg_reg(D19_24XX_MMC_DAT3);
+ omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
+ omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
+ omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
+ }
+
+ /*
+ * Use internal loop-back in MMC/SDIO Module Input Clock
+ * selection
+ */
+ if (mmc_controller->slots[0].internal_clock) {
+ u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+ v |= (1 << 24);
+ omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
+ }
+ }
+}
+
+void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers)
+{
+ int i;
+
+ for (i = 0; i < nr_controllers; i++) {
+ unsigned long base, size;
+ unsigned int irq = 0;
+
+ if (!mmc_data[i])
+ continue;
+
+ omap2_mmc_mux(mmc_data[i], i);
+
+ switch (i) {
+ case 0:
+ base = OMAP2_MMC1_BASE;
+ irq = INT_24XX_MMC_IRQ;
+ break;
+ case 1:
+ base = OMAP2_MMC2_BASE;
+ irq = INT_24XX_MMC2_IRQ;
+ break;
+ case 2:
+ if (!cpu_is_omap34xx())
+ return;
+ base = OMAP3_MMC3_BASE;
+ irq = INT_34XX_MMC3_IRQ;
+ break;
+ default:
+ continue;
+ }
+
+ if (cpu_is_omap2420())
+ size = OMAP2420_MMC_SIZE;
+ else
+ size = HSMMC_SIZE;
+
+ omap_mmc_add(i, base, size, irq, mmc_data[i]);
+ };
+}
+
+#endif
+
+/*-------------------------------------------------------------------------*/
+
#if defined(CONFIG_HDQ_MASTER_OMAP) || defined(CONFIG_HDQ_MASTER_OMAP_MODULE)
#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430)
#define OMAP_HDQ_BASE 0x480B2000
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
-#define OMAP_MMC1_BASE 0x4809c000
-#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x1fc)
-#define OMAP_MMC1_INT INT_24XX_MMC_IRQ
+#define OMAP_MMC_NR_RES 2
-#define OMAP_MMC2_BASE 0x480b4000
-#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x1fc)
-#define OMAP_MMC2_INT INT_24XX_MMC2_IRQ
-
-#else
-
-#define OMAP_MMC1_BASE 0xfffb7800
-#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x7f)
-#define OMAP_MMC1_INT INT_MMC
-
-#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */
-#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x7f)
-#define OMAP_MMC2_INT INT_1610_MMC2
-
-#endif
-
-static struct omap_mmc_platform_data mmc1_data;
-
-static u64 mmc1_dmamask = 0xffffffff;
-
-static struct resource mmc1_resources[] = {
- {
- .start = OMAP_MMC1_BASE,
- .end = OMAP_MMC1_END,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_MMC1_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mmc_omap_device1 = {
- .name = "mmci-omap",
- .id = 1,
- .dev = {
- .dma_mask = &mmc1_dmamask,
- .platform_data = &mmc1_data,
- },
- .num_resources = ARRAY_SIZE(mmc1_resources),
- .resource = mmc1_resources,
-};
-
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
- defined(CONFIG_ARCH_OMAP34XX)
-
-static struct omap_mmc_platform_data mmc2_data;
-
-static u64 mmc2_dmamask = 0xffffffff;
-
-static struct resource mmc2_resources[] = {
- {
- .start = OMAP_MMC2_BASE,
- .end = OMAP_MMC2_END,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_MMC2_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device mmc_omap_device2 = {
- .name = "mmci-omap",
- .id = 2,
- .dev = {
- .dma_mask = &mmc2_dmamask,
- .platform_data = &mmc2_data,
- },
- .num_resources = ARRAY_SIZE(mmc2_resources),
- .resource = mmc2_resources,
-};
-#endif
-
-static inline void omap_init_mmc_conf(const struct omap_mmc_config *mmc_conf)
-{
- if (cpu_is_omap2430() || cpu_is_omap34xx())
- return;
-
- if (mmc_conf->mmc[0].enabled) {
- if (cpu_is_omap24xx()) {
- omap_cfg_reg(H18_24XX_MMC_CMD);
- omap_cfg_reg(H15_24XX_MMC_CLKI);
- omap_cfg_reg(G19_24XX_MMC_CLKO);
- omap_cfg_reg(F20_24XX_MMC_DAT0);
- omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
- omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
- } else {
- omap_cfg_reg(MMC_CMD);
- omap_cfg_reg(MMC_CLK);
- omap_cfg_reg(MMC_DAT0);
- if (cpu_is_omap1710()) {
- omap_cfg_reg(M15_1710_MMC_CLKI);
- omap_cfg_reg(P19_1710_MMC_CMDDIR);
- omap_cfg_reg(P20_1710_MMC_DATDIR0);
- }
- }
- if (mmc_conf->mmc[0].wire4) {
- if (cpu_is_omap24xx()) {
- omap_cfg_reg(H14_24XX_MMC_DAT1);
- omap_cfg_reg(E19_24XX_MMC_DAT2);
- omap_cfg_reg(D19_24XX_MMC_DAT3);
- omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
- omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
- omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
- } else {
- omap_cfg_reg(MMC_DAT1);
- /* NOTE: DAT2 can be on W10 (here) or M15 */
- if (!mmc_conf->mmc[0].nomux)
- omap_cfg_reg(MMC_DAT2);
- omap_cfg_reg(MMC_DAT3);
- }
- }
- }
-
-#ifdef CONFIG_ARCH_OMAP16XX
- /* block 2 is on newer chips, and has many pinout options */
- if (mmc_conf->mmc[1].enabled) {
- if (!mmc_conf->mmc[1].nomux) {
- omap_cfg_reg(Y8_1610_MMC2_CMD);
- omap_cfg_reg(Y10_1610_MMC2_CLK);
- omap_cfg_reg(R18_1610_MMC2_CLKIN);
- omap_cfg_reg(W8_1610_MMC2_DAT0);
- if (mmc_conf->mmc[1].wire4) {
- omap_cfg_reg(V8_1610_MMC2_DAT1);
- omap_cfg_reg(W15_1610_MMC2_DAT2);
- omap_cfg_reg(R10_1610_MMC2_DAT3);
- }
-
- /* These are needed for the level shifter */
- omap_cfg_reg(V9_1610_MMC2_CMDDIR);
- omap_cfg_reg(V5_1610_MMC2_DATDIR0);
- omap_cfg_reg(W19_1610_MMC2_DATDIR1);
- }
-
- /* Feedback clock must be set on OMAP-1710 MMC2 */
- if (cpu_is_omap1710())
- omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
- MOD_CONF_CTRL_1);
- }
-#endif
-}
-
-static void __init omap_init_mmc(void)
+/*
+ * Register MMC devices. Called from mach-omap1 and mach-omap2 device init.
+ */
+int __init omap_mmc_add(int id, unsigned long base, unsigned long size,
+ unsigned int irq, struct omap_mmc_platform_data *data)
{
- const struct omap_mmc_config *mmc_conf;
-
- /* NOTE: assumes MMC was never (wrongly) enabled */
- mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
- if (!mmc_conf)
- return;
-
- omap_init_mmc_conf(mmc_conf);
-
- if (mmc_conf->mmc[0].enabled) {
- mmc1_data.conf = mmc_conf->mmc[0];
- (void) platform_device_register(&mmc_omap_device1);
- }
-
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
- defined(CONFIG_ARCH_OMAP34XX)
- if (mmc_conf->mmc[1].enabled) {
- mmc2_data.conf = mmc_conf->mmc[1];
- (void) platform_device_register(&mmc_omap_device2);
- }
-#endif
-}
+ struct platform_device *pdev;
+ struct resource res[OMAP_MMC_NR_RES];
+ int ret;
+
+ pdev = platform_device_alloc("mmci-omap", id);
+ if (!pdev)
+ return -ENOMEM;
+
+ memset(res, 0, OMAP_MMC_NR_RES * sizeof(struct resource));
+ res[0].start = base;
+ res[0].end = base + size - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = res[1].end = irq;
+ res[1].flags = IORESOURCE_IRQ;
+
+ ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res));
+ if (ret == 0)
+ ret = platform_device_add_data(pdev, data, sizeof(*data));
+ if (ret)
+ goto fail;
+
+ ret = platform_device_add(pdev);
+ if (ret)
+ goto fail;
+ return 0;
-void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info)
-{
- switch (host) {
- case 1:
- mmc1_data = *info;
- break;
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \
- defined(CONFIG_ARCH_OMAP34XX)
- case 2:
- mmc2_data = *info;
- break;
-#endif
- default:
- BUG();
- }
+fail:
+ platform_device_put(pdev);
+ return ret;
}
-#else
-static inline void omap_init_mmc(void) {}
-void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info) {}
#endif
/*-------------------------------------------------------------------------*/
*/
omap_init_dsp();
omap_init_kp();
- omap_init_mmc();
omap_init_uwire();
omap_init_wdt();
omap_init_rng();
#ifndef __ASM_ARCH_OMAP_H2_H
#define __ASM_ARCH_OMAP_H2_H
-/* Placeholder for H2 specific defines */
-
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define OMAP1610_ETHR_START 0x04000300
+#define H2_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
+# define H2_TPS_GPIO_MMC_PWR_EN (H2_TPS_GPIO_BASE + 3)
+
extern void h2_mmc_init(void);
-extern void h2_mmc_slot_cover_handler(void *arg, int state);
#endif /* __ASM_ARCH_OMAP_H2_H */
/* Different peripheral ids */
#define OMAP_TAG_CLOCK 0x4f01
-#define OMAP_TAG_MMC 0x4f02
#define OMAP_TAG_SERIAL_CONSOLE 0x4f03
#define OMAP_TAG_USB 0x4f04
#define OMAP_TAG_LCD 0x4f05
u8 system_clock_type;
};
-struct omap_mmc_conf {
- unsigned enabled:1;
- /* nomux means "standard" muxing is wrong on this board, and that
- * board-specific code handled it before common init logic.
- */
- unsigned nomux:1;
- /* switch pin can be for card detect (default) or card cover */
- unsigned cover:1;
- /* 4 wire signaling is optional, and is only used for SD/SDIO */
- unsigned wire4:1;
- /* use the internal clock */
- unsigned internal_clock:1;
- s16 power_pin;
- s16 switch_pin;
- s16 wp_pin;
-};
-
-struct omap_mmc_config {
- struct omap_mmc_conf mmc[2];
-};
-
struct omap_serial_console_config {
u8 console_uart;
u32 console_speed;
#include <mach/board.h>
+#define OMAP15XX_NR_MMC 1
+#define OMAP16XX_NR_MMC 2
+#define OMAP1_MMC_SIZE 0x080
+#define OMAP1_MMC1_BASE 0xfffb7800
+#define OMAP1_MMC2_BASE 0xfffb7c00 /* omap16xx only */
+
+#define OMAP24XX_NR_MMC 2
+#define OMAP34XX_NR_MMC 3
+#define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE
+#define HSMMC_SIZE 0x200
+#define OMAP2_MMC1_BASE 0x4809c000
+#define OMAP2_MMC2_BASE 0x480b4000
+#define OMAP3_MMC3_BASE 0x480ad000
+#define HSMMC3 (1 << 2)
+#define HSMMC2 (1 << 1)
+#define HSMMC1 (1 << 0)
+
#define OMAP_MMC_MAX_SLOTS 2
struct omap_mmc_platform_data {
- struct omap_mmc_conf conf;
- /* number of slots on board */
+ /* number of slots per controller */
unsigned nr_slots:2;
/* set if your board has components or wiring that limits the
int (*suspend)(struct device *dev, int slot);
int (*resume)(struct device *dev, int slot);
+ u64 dma_mask;
+
struct omap_mmc_slot_data {
+
+ /*
+ * nomux means "standard" muxing is wrong on this board, and
+ * that board-specific code handled it before common init logic.
+ */
+ unsigned nomux:1;
+
+ /* switch pin can be for card detect (default) or card cover */
+ unsigned cover:1;
+
+ /* 4 wire signaling is optional, and is only used for SD/SDIO */
+ unsigned wire4:1;
+
+ /* use the internal clock */
+ unsigned internal_clock:1;
+ s16 power_pin;
+ s16 switch_pin;
+
int (* set_bus_mode)(struct device *dev, int slot, int bus_mode);
int (* set_power)(struct device *dev, int slot, int power_on, int vdd);
int (* get_ro)(struct device *dev, int slot);
/* return MMC cover switch state, can be NULL if not supported.
*
* possible return values:
- * 0 - open
- * 1 - closed
+ * 0 - closed
+ * 1 - open
*/
int (* get_cover_state)(struct device *dev, int slot);
} slots[OMAP_MMC_MAX_SLOTS];
};
-extern void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info);
-
/* called from board-specific card detection service routine */
extern void omap_mmc_notify_cover_event(struct device *dev, int slot, int is_closed);
+#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+ defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers);
+void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers);
+void hsmmc_init(int controller_mask);
+int omap_mmc_add(int id, unsigned long base, unsigned long size,
+ unsigned int irq, struct omap_mmc_platform_data *data);
+#else
+static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers)
+{
+}
+static inline void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data,
+ int nr_controllers)
+{
+}
+static inline void hsmmc_init(int controller_mask)
+{
+}
+static inline int omap_mmc_add(int id, unsigned long base, unsigned long size,
+ unsigned int irq, struct omap_mmc_platform_data *data)
+{
+ return 0;
+}
+
+#endif
#endif
}
if (is_read) {
- if (host->id == 1) {
+ if (host->id == 0) {
sync_dev = OMAP_DMA_MMC_RX;
dma_dev_name = "MMC1 read";
} else {
dma_dev_name = "MMC2 read";
}
} else {
- if (host->id == 1) {
+ if (host->id == 0) {
sync_dev = OMAP_DMA_MMC_TX;
dma_dev_name = "MMC1 write";
} else {
host->slots[id] = slot;
mmc->caps = 0;
- if (host->pdata->conf.wire4)
+ if (host->pdata->slots[id].wire4)
mmc->caps |= MMC_CAP_4_BIT_DATA;
mmc->ops = &mmc_omap_ops;
host->irq = irq;
host->use_dma = 1;
+ host->dev->dma_mask = &pdata->dma_mask;
host->dma_ch = -1;
host->irq = irq;
projects / linux-2.6-omap-h63xx.git / commitdiff