struct ubi_vid_hdr *vh = NULL;
unsigned long long sqnum2 = be64_to_cpu(vid_hdr->sqnum);
- if (seb->sqnum == 0 && sqnum2 == 0) {
- long long abs;
- long long v1 = seb->leb_ver, v2 = be32_to_cpu(vid_hdr->leb_ver);
-
+ if (sqnum2 == seb->sqnum) {
/*
- * UBI constantly increases the logical eraseblock version
- * number and it can overflow. Thus, we have to bear in mind
- * that versions that are close to %0xFFFFFFFF are less then
- * versions that are close to %0.
- *
- * The UBI WL sub-system guarantees that the number of pending
- * tasks is not greater then %0x7FFFFFFF. So, if the difference
- * between any two versions is greater or equivalent to
- * %0x7FFFFFFF, there was an overflow and the logical
- * eraseblock with lower version is actually newer then the one
- * with higher version.
- *
- * FIXME: but this is anyway obsolete and will be removed at
- * some point.
+ * This must be a really ancient UBI image which has been
+ * created before sequence numbers support has been added. At
+ * that times we used 32-bit LEB versions stored in logical
+ * eraseblocks. That was before UBI got into mainline. We do not
+ * support these images anymore. Well, those images will work
+ * still work, but only if no unclean reboots happened.
*/
- dbg_bld("using old crappy leb_ver stuff");
-
- if (v1 == v2) {
- ubi_err("PEB %d and PEB %d have the same version %lld",
- seb->pnum, pnum, v1);
- return -EINVAL;
- }
+ ubi_err("unsupported on-flash UBI format\n");
+ return -EINVAL;
+ }
- abs = v1 - v2;
- if (abs < 0)
- abs = -abs;
-
- if (abs < 0x7FFFFFFF)
- /* Non-overflow situation */
- second_is_newer = (v2 > v1);
- else
- second_is_newer = (v2 < v1);
- } else
- /* Obviously the LEB with lower sequence counter is older */
- second_is_newer = sqnum2 > seb->sqnum;
+ /* Obviously the LEB with lower sequence counter is older */
+ second_is_newer = !!(sqnum2 > seb->sqnum);
/*
* Now we know which copy is newer. If the copy flag of the PEB with
* check data CRC. For the second PEB we already have the VID header,
* for the first one - we'll need to re-read it from flash.
*
- * FIXME: this may be optimized so that we wouldn't read twice.
+ * Note: this may be optimized so that we wouldn't read twice.
*/
if (second_is_newer) {
int bitflips)
{
int err, vol_id, lnum;
- uint32_t leb_ver;
unsigned long long sqnum;
struct ubi_scan_volume *sv;
struct ubi_scan_leb *seb;
vol_id = be32_to_cpu(vid_hdr->vol_id);
lnum = be32_to_cpu(vid_hdr->lnum);
sqnum = be64_to_cpu(vid_hdr->sqnum);
- leb_ver = be32_to_cpu(vid_hdr->leb_ver);
- dbg_bld("PEB %d, LEB %d:%d, EC %d, sqnum %llu, ver %u, bitflips %d",
- pnum, vol_id, lnum, ec, sqnum, leb_ver, bitflips);
+ dbg_bld("PEB %d, LEB %d:%d, EC %d, sqnum %llu, bitflips %d",
+ pnum, vol_id, lnum, ec, sqnum, bitflips);
sv = add_volume(si, vol_id, pnum, vid_hdr);
if (IS_ERR(sv) < 0)
*/
dbg_bld("this LEB already exists: PEB %d, sqnum %llu, "
- "LEB ver %u, EC %d", seb->pnum, seb->sqnum,
- seb->leb_ver, seb->ec);
-
- /*
- * Make sure that the logical eraseblocks have different
- * versions. Otherwise the image is bad.
- */
- if (seb->leb_ver == leb_ver && leb_ver != 0) {
- ubi_err("two LEBs with same version %u", leb_ver);
- ubi_dbg_dump_seb(seb, 0);
- ubi_dbg_dump_vid_hdr(vid_hdr);
- return -EINVAL;
- }
+ "EC %d", seb->pnum, seb->sqnum, seb->ec);
/*
* Make sure that the logical eraseblocks have different
* sequence numbers. Otherwise the image is bad.
*
- * FIXME: remove 'sqnum != 0' check when leb_ver is removed.
+ * However, if the sequence number is zero, we assume it must
+ * be an ancient UBI image from the era when UBI did not have
+ * sequence numbers. We still can attach these images, unless
+ * there is a need to distinguish between old and new
+ * eraseblocks, in which case we'll refuse the image in
+ * 'compare_lebs()'. In other words, we attach old clean
+ * images, but refuse attaching old images with duplicated
+ * logical eraseblocks because there was an unclean reboot.
*/
if (seb->sqnum == sqnum && sqnum != 0) {
ubi_err("two LEBs with same sequence number %llu",
seb->pnum = pnum;
seb->scrub = ((cmp_res & 2) || bitflips);
seb->sqnum = sqnum;
- seb->leb_ver = leb_ver;
if (sv->highest_lnum == lnum)
sv->last_data_size =
seb->lnum = lnum;
seb->sqnum = sqnum;
seb->scrub = bitflips;
- seb->leb_ver = leb_ver;
if (sv->highest_lnum <= lnum) {
sv->highest_lnum = lnum;
ubi_err("bad data_pad %d", sv->data_pad);
goto bad_vid_hdr;
}
-
- if (seb->leb_ver != be32_to_cpu(vidh->leb_ver)) {
- ubi_err("bad leb_ver %u", seb->leb_ver);
- goto bad_vid_hdr;
- }
}
if (!last_seb)
* %UBI_COMPAT_IGNORE, %UBI_COMPAT_PRESERVE, or %UBI_COMPAT_REJECT)
* @vol_id: ID of this volume
* @lnum: logical eraseblock number
- * @leb_ver: version of this logical eraseblock (IMPORTANT: obsolete, to be
- * removed, kept only for not breaking older UBI users)
+ * @padding1: reserved for future, zeroes
* @data_size: how many bytes of data this logical eraseblock contains
* @used_ebs: total number of used logical eraseblocks in this volume
* @data_pad: how many bytes at the end of this physical eraseblock are not
* used
* @data_crc: CRC checksum of the data stored in this logical eraseblock
- * @padding1: reserved for future, zeroes
- * @sqnum: sequence number
* @padding2: reserved for future, zeroes
+ * @sqnum: sequence number
+ * @padding3: reserved for future, zeroes
* @hdr_crc: volume identifier header CRC checksum
*
* The @sqnum is the value of the global sequence counter at the time when this
* checksum is correct, this physical eraseblock is selected (P1). Otherwise
* the older one (P) is selected.
*
- * Note, there is an obsolete @leb_ver field which was used instead of @sqnum
- * in the past. But it is not used anymore and we keep it in order to be able
- * to deal with old UBI images. It will be removed at some point.
- *
* There are 2 sorts of volumes in UBI: user volumes and internal volumes.
* Internal volumes are not seen from outside and are used for various internal
* UBI purposes. In this implementation there is only one internal volume - the
__u8 compat;
__be32 vol_id;
__be32 lnum;
- __be32 leb_ver; /* obsolete, to be removed, don't use */
+ __u8 padding1[4];
__be32 data_size;
__be32 used_ebs;
__be32 data_pad;
__be32 data_crc;
- __u8 padding1[4];
+ __u8 padding2[4];
__be64 sqnum;
- __u8 padding2[12];
+ __u8 padding3[12];
__be32 hdr_crc;
} __attribute__ ((packed));
projects / linux-2.6-omap-h63xx.git / commitdiff