--- /dev/null
+/*
+ * am200epd.c -- Platform device for AM200 EPD kit
+ *
+ * Copyright (C) 2008, Jaya Kumar
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
+ *
+ * This work was made possible by help and equipment support from E-Ink
+ * Corporation. http://support.eink.com/community
+ *
+ * This driver is written to be used with the Metronome display controller.
+ * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600
+ * Vizplex EPD on a Gumstix board using the Lyre interface board.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+
+#include <mach/pxafb.h>
+
+#include <video/metronomefb.h>
+
+static unsigned int panel_type = 6;
+static struct platform_device *am200_device;
+static struct metronome_board am200_board;
+
+static struct pxafb_mode_info am200_fb_mode_9inch7 = {
+ .pixclock = 40000,
+ .xres = 1200,
+ .yres = 842,
+ .bpp = 16,
+ .hsync_len = 2,
+ .left_margin = 2,
+ .right_margin = 2,
+ .vsync_len = 1,
+ .upper_margin = 2,
+ .lower_margin = 25,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+};
+
+static struct pxafb_mode_info am200_fb_mode_8inch = {
+ .pixclock = 40000,
+ .xres = 1088,
+ .yres = 791,
+ .bpp = 16,
+ .hsync_len = 28,
+ .left_margin = 8,
+ .right_margin = 30,
+ .vsync_len = 8,
+ .upper_margin = 10,
+ .lower_margin = 8,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+};
+
+static struct pxafb_mode_info am200_fb_mode_6inch = {
+ .pixclock = 40189,
+ .xres = 832,
+ .yres = 622,
+ .bpp = 16,
+ .hsync_len = 28,
+ .left_margin = 34,
+ .right_margin = 34,
+ .vsync_len = 25,
+ .upper_margin = 0,
+ .lower_margin = 2,
+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+};
+
+static struct pxafb_mach_info am200_fb_info = {
+ .modes = &am200_fb_mode_6inch,
+ .num_modes = 1,
+ .lcd_conn = LCD_TYPE_COLOR_TFT | LCD_PCLK_EDGE_FALL |
+ LCD_AC_BIAS_FREQ(24),
+};
+
+/* register offsets for gpio control */
+#define LED_GPIO_PIN 51
+#define STDBY_GPIO_PIN 48
+#define RST_GPIO_PIN 49
+#define RDY_GPIO_PIN 32
+#define ERR_GPIO_PIN 17
+#define PCBPWR_GPIO_PIN 16
+static int gpios[] = { LED_GPIO_PIN , STDBY_GPIO_PIN , RST_GPIO_PIN,
+ RDY_GPIO_PIN, ERR_GPIO_PIN, PCBPWR_GPIO_PIN };
+static char *gpio_names[] = { "LED" , "STDBY" , "RST", "RDY", "ERR", "PCBPWR" };
+
+static int am200_init_gpio_regs(struct metronomefb_par *par)
+{
+ int i;
+ int err;
+
+ for (i = 0; i < ARRAY_SIZE(gpios); i++) {
+ err = gpio_request(gpios[i], gpio_names[i]);
+ if (err) {
+ dev_err(&am200_device->dev, "failed requesting "
+ "gpio %s, err=%d\n", gpio_names[i], err);
+ goto err_req_gpio;
+ }
+ }
+
+ gpio_direction_output(LED_GPIO_PIN, 0);
+ gpio_direction_output(STDBY_GPIO_PIN, 0);
+ gpio_direction_output(RST_GPIO_PIN, 0);
+
+ gpio_direction_input(RDY_GPIO_PIN);
+ gpio_direction_input(ERR_GPIO_PIN);
+
+ gpio_direction_output(PCBPWR_GPIO_PIN, 0);
+
+ return 0;
+
+err_req_gpio:
+ while (i > 0)
+ gpio_free(gpios[i--]);
+
+ return err;
+}
+
+static void am200_cleanup(struct metronomefb_par *par)
+{
+ int i;
+
+ free_irq(IRQ_GPIO(RDY_GPIO_PIN), par);
+
+ for (i = 0; i < ARRAY_SIZE(gpios); i++)
+ gpio_free(gpios[i]);
+}
+
+static int am200_share_video_mem(struct fb_info *info)
+{
+ /* rough check if this is our desired fb and not something else */
+ if ((info->var.xres != am200_fb_info.modes->xres)
+ || (info->var.yres != am200_fb_info.modes->yres))
+ return 0;
+
+ /* we've now been notified that we have our new fb */
+ am200_board.metromem = info->screen_base;
+ am200_board.host_fbinfo = info;
+
+ /* try to refcount host drv since we are the consumer after this */
+ if (!try_module_get(info->fbops->owner))
+ return -ENODEV;
+
+ return 0;
+}
+
+static int am200_unshare_video_mem(struct fb_info *info)
+{
+ dev_dbg(&am200_device->dev, "ENTER %s\n", __func__);
+
+ if (info != am200_board.host_fbinfo)
+ return 0;
+
+ module_put(am200_board.host_fbinfo->fbops->owner);
+ return 0;
+}
+
+static int am200_fb_notifier_callback(struct notifier_block *self,
+ unsigned long event, void *data)
+{
+ struct fb_event *evdata = data;
+ struct fb_info *info = evdata->info;
+
+ dev_dbg(&am200_device->dev, "ENTER %s\n", __func__);
+
+ if (event == FB_EVENT_FB_REGISTERED)
+ return am200_share_video_mem(info);
+ else if (event == FB_EVENT_FB_UNREGISTERED)
+ return am200_unshare_video_mem(info);
+
+ return 0;
+}
+
+static struct notifier_block am200_fb_notif = {
+ .notifier_call = am200_fb_notifier_callback,
+};
+
+/* this gets called as part of our init. these steps must be done now so
+ * that we can use set_pxa_fb_info */
+static void __init am200_presetup_fb(void)
+{
+ int fw;
+ int fh;
+ int padding_size;
+ int totalsize;
+
+ switch (panel_type) {
+ case 6:
+ am200_fb_info.modes = &am200_fb_mode_6inch;
+ break;
+ case 8:
+ am200_fb_info.modes = &am200_fb_mode_8inch;
+ break;
+ case 97:
+ am200_fb_info.modes = &am200_fb_mode_9inch7;
+ break;
+ default:
+ dev_err(&am200_device->dev, "invalid panel_type selection,"
+ " setting to 6\n");
+ am200_fb_info.modes = &am200_fb_mode_6inch;
+ break;
+ }
+
+ /* the frame buffer is divided as follows:
+ command | CRC | padding
+ 16kb waveform data | CRC | padding
+ image data | CRC
+ */
+
+ fw = am200_fb_info.modes->xres;
+ fh = am200_fb_info.modes->yres;
+
+ /* waveform must be 16k + 2 for checksum */
+ am200_board.wfm_size = roundup(16*1024 + 2, fw);
+
+ padding_size = PAGE_SIZE + (4 * fw);
+
+ /* total is 1 cmd , 1 wfm, padding and image */
+ totalsize = fw + am200_board.wfm_size + padding_size + (fw*fh);
+
+ /* save this off because we're manipulating fw after this and
+ * we'll need it when we're ready to setup the framebuffer */
+ am200_board.fw = fw;
+ am200_board.fh = fh;
+
+ /* the reason we do this adjustment is because we want to acquire
+ * more framebuffer memory without imposing custom awareness on the
+ * underlying pxafb driver */
+ am200_fb_info.modes->yres = DIV_ROUND_UP(totalsize, fw);
+
+ /* we divide since we told the LCD controller we're 16bpp */
+ am200_fb_info.modes->xres /= 2;
+
+ set_pxa_fb_info(&am200_fb_info);
+
+}
+
+/* this gets called by metronomefb as part of its init, in our case, we
+ * have already completed initial framebuffer init in presetup_fb so we
+ * can just setup the fb access pointers */
+static int am200_setup_fb(struct metronomefb_par *par)
+{
+ int fw;
+ int fh;
+
+ fw = am200_board.fw;
+ fh = am200_board.fh;
+
+ /* metromem was set up by the notifier in share_video_mem so now
+ * we can use its value to calculate the other entries */
+ par->metromem_cmd = (struct metromem_cmd *) am200_board.metromem;
+ par->metromem_wfm = am200_board.metromem + fw;
+ par->metromem_img = par->metromem_wfm + am200_board.wfm_size;
+ par->metromem_img_csum = (u16 *) (par->metromem_img + (fw * fh));
+ par->metromem_dma = am200_board.host_fbinfo->fix.smem_start;
+
+ return 0;
+}
+
+static int am200_get_panel_type(void)
+{
+ return panel_type;
+}
+
+static irqreturn_t am200_handle_irq(int irq, void *dev_id)
+{
+ struct metronomefb_par *par = dev_id;
+
+ wake_up_interruptible(&par->waitq);
+ return IRQ_HANDLED;
+}
+
+static int am200_setup_irq(struct fb_info *info)
+{
+ int ret;
+
+ ret = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq,
+ IRQF_DISABLED|IRQF_TRIGGER_FALLING,
+ "AM200", info->par);
+ if (ret)
+ dev_err(&am200_device->dev, "request_irq failed: %d\n", ret);
+
+ return ret;
+}
+
+static void am200_set_rst(struct metronomefb_par *par, int state)
+{
+ gpio_set_value(RST_GPIO_PIN, state);
+}
+
+static void am200_set_stdby(struct metronomefb_par *par, int state)
+{
+ gpio_set_value(STDBY_GPIO_PIN, state);
+}
+
+static int am200_wait_event(struct metronomefb_par *par)
+{
+ return wait_event_timeout(par->waitq, gpio_get_value(RDY_GPIO_PIN), HZ);
+}
+
+static int am200_wait_event_intr(struct metronomefb_par *par)
+{
+ return wait_event_interruptible_timeout(par->waitq,
+ gpio_get_value(RDY_GPIO_PIN), HZ);
+}
+
+static struct metronome_board am200_board = {
+ .owner = THIS_MODULE,
+ .setup_irq = am200_setup_irq,
+ .setup_io = am200_init_gpio_regs,
+ .setup_fb = am200_setup_fb,
+ .set_rst = am200_set_rst,
+ .set_stdby = am200_set_stdby,
+ .met_wait_event = am200_wait_event,
+ .met_wait_event_intr = am200_wait_event_intr,
+ .get_panel_type = am200_get_panel_type,
+ .cleanup = am200_cleanup,
+};
+
+static int __init am200_init(void)
+{
+ int ret;
+
+ /* before anything else, we request notification for any fb
+ * creation events */
+ fb_register_client(&am200_fb_notif);
+
+ /* request our platform independent driver */
+ request_module("metronomefb");
+
+ am200_device = platform_device_alloc("metronomefb", -1);
+ if (!am200_device)
+ return -ENOMEM;
+
+ /* the am200_board that will be seen by metronomefb is a copy */
+ platform_device_add_data(am200_device, &am200_board,
+ sizeof(am200_board));
+
+ /* this _add binds metronomefb to am200. metronomefb refcounts am200 */
+ ret = platform_device_add(am200_device);
+
+ if (ret) {
+ platform_device_put(am200_device);
+ fb_unregister_client(&am200_fb_notif);
+ return ret;
+ }
+
+ am200_presetup_fb();
+
+ return 0;
+}
+
+module_param(panel_type, uint, 0);
+MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97");
+
+module_init(am200_init);
+
+MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
+MODULE_AUTHOR("Jaya Kumar");
+MODULE_LICENSE("GPL");
+++ /dev/null
-/*
- * linux/drivers/video/am200epd.c -- Platform device for AM200 EPD kit
- *
- * Copyright (C) 2008, Jaya Kumar
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file COPYING in the main directory of this archive for
- * more details.
- *
- * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
- *
- * This work was made possible by help and equipment support from E-Ink
- * Corporation. http://support.eink.com/community
- *
- * This driver is written to be used with the Metronome display controller.
- * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600
- * Vizplex EPD on a Gumstix board using the Lyre interface board.
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/fb.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/list.h>
-#include <linux/uaccess.h>
-#include <linux/irq.h>
-
-#include <video/metronomefb.h>
-
-#include <mach/pxa-regs.h>
-
-/* register offsets for gpio control */
-#define LED_GPIO_PIN 51
-#define STDBY_GPIO_PIN 48
-#define RST_GPIO_PIN 49
-#define RDY_GPIO_PIN 32
-#define ERR_GPIO_PIN 17
-#define PCBPWR_GPIO_PIN 16
-
-#define AF_SEL_GPIO_N 0x3
-#define GAFR0_U_OFFSET(pin) ((pin - 16) * 2)
-#define GAFR1_L_OFFSET(pin) ((pin - 32) * 2)
-#define GAFR1_U_OFFSET(pin) ((pin - 48) * 2)
-#define GPDR1_OFFSET(pin) (pin - 32)
-#define GPCR1_OFFSET(pin) (pin - 32)
-#define GPSR1_OFFSET(pin) (pin - 32)
-#define GPCR0_OFFSET(pin) (pin)
-#define GPSR0_OFFSET(pin) (pin)
-
-static void am200_set_gpio_output(int pin, int val)
-{
- u8 index;
-
- index = pin >> 4;
-
- switch (index) {
- case 1:
- if (val)
- GPSR0 |= (1 << GPSR0_OFFSET(pin));
- else
- GPCR0 |= (1 << GPCR0_OFFSET(pin));
- break;
- case 2:
- break;
- case 3:
- if (val)
- GPSR1 |= (1 << GPSR1_OFFSET(pin));
- else
- GPCR1 |= (1 << GPCR1_OFFSET(pin));
- break;
- default:
- printk(KERN_ERR "unimplemented\n");
- }
-}
-
-static void __devinit am200_init_gpio_pin(int pin, int dir)
-{
- u8 index;
- /* dir 0 is output, 1 is input
- - do 2 things here:
- - set gpio alternate function to standard gpio
- - set gpio direction to input or output */
-
- index = pin >> 4;
- switch (index) {
- case 1:
- GAFR0_U &= ~(AF_SEL_GPIO_N << GAFR0_U_OFFSET(pin));
-
- if (dir)
- GPDR0 &= ~(1 << pin);
- else
- GPDR0 |= (1 << pin);
- break;
- case 2:
- GAFR1_L &= ~(AF_SEL_GPIO_N << GAFR1_L_OFFSET(pin));
-
- if (dir)
- GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
- else
- GPDR1 |= (1 << GPDR1_OFFSET(pin));
- break;
- case 3:
- GAFR1_U &= ~(AF_SEL_GPIO_N << GAFR1_U_OFFSET(pin));
-
- if (dir)
- GPDR1 &= ~(1 << GPDR1_OFFSET(pin));
- else
- GPDR1 |= (1 << GPDR1_OFFSET(pin));
- break;
- default:
- printk(KERN_ERR "unimplemented\n");
- }
-}
-
-static void am200_init_gpio_regs(struct metronomefb_par *par)
-{
- am200_init_gpio_pin(LED_GPIO_PIN, 0);
- am200_set_gpio_output(LED_GPIO_PIN, 0);
-
- am200_init_gpio_pin(STDBY_GPIO_PIN, 0);
- am200_set_gpio_output(STDBY_GPIO_PIN, 0);
-
- am200_init_gpio_pin(RST_GPIO_PIN, 0);
- am200_set_gpio_output(RST_GPIO_PIN, 0);
-
- am200_init_gpio_pin(RDY_GPIO_PIN, 1);
-
- am200_init_gpio_pin(ERR_GPIO_PIN, 1);
-
- am200_init_gpio_pin(PCBPWR_GPIO_PIN, 0);
- am200_set_gpio_output(PCBPWR_GPIO_PIN, 0);
-}
-
-static void am200_disable_lcd_controller(struct metronomefb_par *par)
-{
- LCSR = 0xffffffff; /* Clear LCD Status Register */
- LCCR0 |= LCCR0_DIS; /* Disable LCD Controller */
-
- /* we reset and just wait for things to settle */
- msleep(200);
-}
-
-static void am200_enable_lcd_controller(struct metronomefb_par *par)
-{
- LCSR = 0xffffffff;
- FDADR0 = par->metromem_desc_dma;
- LCCR0 |= LCCR0_ENB;
-}
-
-static void am200_init_lcdc_regs(struct metronomefb_par *par)
-{
- /* here we do:
- - disable the lcd controller
- - setup lcd control registers
- - setup dma descriptor
- - reenable lcd controller
- */
-
- /* disable the lcd controller */
- am200_disable_lcd_controller(par);
-
- /* setup lcd control registers */
- LCCR0 = LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM | LCCR0_PAS
- | LCCR0_QDM | LCCR0_BM | LCCR0_OUM;
-
- LCCR1 = (par->info->var.xres/2 - 1) /* pixels per line */
- | (27 << 10) /* hsync pulse width - 1 */
- | (33 << 16) /* eol pixel count */
- | (33 << 24); /* bol pixel count */
-
- LCCR2 = (par->info->var.yres - 1) /* lines per panel */
- | (24 << 10) /* vsync pulse width - 1 */
- | (2 << 16) /* eof pixel count */
- | (0 << 24); /* bof pixel count */
-
- LCCR3 = 2 /* pixel clock divisor */
- | (24 << 8) /* AC Bias pin freq */
- | LCCR3_16BPP /* BPP */
- | LCCR3_PCP; /* PCP falling edge */
-
-}
-
-static void am200_post_dma_setup(struct metronomefb_par *par)
-{
- par->metromem_desc->mFDADR0 = par->metromem_desc_dma;
- par->metromem_desc->mFSADR0 = par->metromem_dma;
- par->metromem_desc->mFIDR0 = 0;
- par->metromem_desc->mLDCMD0 = par->info->var.xres
- * par->info->var.yres;
- am200_enable_lcd_controller(par);
-}
-
-static void am200_free_irq(struct fb_info *info)
-{
- free_irq(IRQ_GPIO(RDY_GPIO_PIN), info);
-}
-
-static irqreturn_t am200_handle_irq(int irq, void *dev_id)
-{
- struct fb_info *info = dev_id;
- struct metronomefb_par *par = info->par;
-
- wake_up_interruptible(&par->waitq);
- return IRQ_HANDLED;
-}
-
-static int am200_setup_irq(struct fb_info *info)
-{
- int retval;
-
- retval = request_irq(IRQ_GPIO(RDY_GPIO_PIN), am200_handle_irq,
- IRQF_DISABLED, "AM200", info);
- if (retval) {
- printk(KERN_ERR "am200epd: request_irq failed: %d\n", retval);
- return retval;
- }
-
- return set_irq_type(IRQ_GPIO(RDY_GPIO_PIN), IRQ_TYPE_EDGE_FALLING);
-}
-
-static void am200_set_rst(struct metronomefb_par *par, int state)
-{
- am200_set_gpio_output(RST_GPIO_PIN, state);
-}
-
-static void am200_set_stdby(struct metronomefb_par *par, int state)
-{
- am200_set_gpio_output(STDBY_GPIO_PIN, state);
-}
-
-static int am200_wait_event(struct metronomefb_par *par)
-{
- return wait_event_timeout(par->waitq, (GPLR1 & 0x01), HZ);
-}
-
-static int am200_wait_event_intr(struct metronomefb_par *par)
-{
- return wait_event_interruptible_timeout(par->waitq, (GPLR1 & 0x01), HZ);
-}
-
-static struct metronome_board am200_board = {
- .owner = THIS_MODULE,
- .free_irq = am200_free_irq,
- .setup_irq = am200_setup_irq,
- .init_gpio_regs = am200_init_gpio_regs,
- .init_lcdc_regs = am200_init_lcdc_regs,
- .post_dma_setup = am200_post_dma_setup,
- .set_rst = am200_set_rst,
- .set_stdby = am200_set_stdby,
- .met_wait_event = am200_wait_event,
- .met_wait_event_intr = am200_wait_event_intr,
-};
-
-static struct platform_device *am200_device;
-
-static int __init am200_init(void)
-{
- int ret;
-
- /* request our platform independent driver */
- request_module("metronomefb");
-
- am200_device = platform_device_alloc("metronomefb", -1);
- if (!am200_device)
- return -ENOMEM;
-
- platform_device_add_data(am200_device, &am200_board,
- sizeof(am200_board));
-
- /* this _add binds metronomefb to am200. metronomefb refcounts am200 */
- ret = platform_device_add(am200_device);
-
- if (ret)
- platform_device_put(am200_device);
-
- return ret;
-}
-
-static void __exit am200_exit(void)
-{
- platform_device_unregister(am200_device);
-}
-
-module_init(am200_init);
-module_exit(am200_exit);
-
-MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
-MODULE_AUTHOR("Jaya Kumar");
-MODULE_LICENSE("GPL");
projects / linux-2.6-omap-h63xx.git / commitdiff