--- /dev/null
+/*
+ * arch/arm/mach-lh7a40x/clcd.c
+ *
+ * Copyright (C) 2004 Marc Singer
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+
+//#include <linux/module.h>
+//#include <linux/time.h>
+//#include <asm/hardware.h>
+
+//#include <asm/mach/time.h>
+#include <asm/irq.h>
+#include <asm/mach/irq.h>
+
+#include <asm/system.h>
+#include <asm/hardware.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/clcd.h>
+
+#define HRTFTC_HRSETUP __REG(HRTFTC_PHYS + 0x00)
+#define HRTFTC_HRCON __REG(HRTFTC_PHYS + 0x04)
+#define HRTFTC_HRTIMING1 __REG(HRTFTC_PHYS + 0x08)
+#define HRTFTC_HRTIMING2 __REG(HRTFTC_PHYS + 0x0c)
+
+#define ALI_SETUP __REG(ALI_PHYS + 0x00)
+#define ALI_CONTROL __REG(ALI_PHYS + 0x04)
+#define ALI_TIMING1 __REG(ALI_PHYS + 0x08)
+#define ALI_TIMING2 __REG(ALI_PHYS + 0x0c)
+
+#include "lcd-panel.h"
+
+static void lh7a40x_clcd_disable (struct clcd_fb *fb)
+{
+#if defined (CONFIG_MACH_LPD7A400)
+ CPLD_CONTROL &= ~(1<<1); /* Disable LCD Vee */
+#endif
+
+#if defined (CONFIG_MACH_LPD7A404)
+ GPIO_PCD &= ~(1<<3); /* Disable LCD Vee */
+#endif
+
+#if defined (CONFIG_ARCH_LH7A400)
+ HRTFTC_HRSETUP &= ~(1<<13); /* Disable HRTFT controller */
+#endif
+
+#if defined (CONFIG_ARCH_LH7A404)
+ ALI_SETUP &= ~(1<<13); /* Disable ALI */
+#endif
+}
+
+static void lh7a40x_clcd_enable (struct clcd_fb *fb)
+{
+ struct clcd_panel_extra* extra
+ = (struct clcd_panel_extra*) fb->board_data;
+
+#if defined (CONFIG_MACH_LPD7A400)
+ CPLD_CONTROL |= (1<<1); /* Enable LCD Vee */
+#endif
+
+#if defined (CONFIG_MACH_LPD7A404)
+ GPIO_PCDD &= ~(1<<3); /* Enable LCD Vee */
+ GPIO_PCD |= (1<<3);
+#endif
+
+#if defined (CONFIG_ARCH_LH7A400)
+
+ if (extra) {
+ HRTFTC_HRSETUP
+ = (1 << 13)
+ | ((fb->fb.var.xres - 1) << 4)
+ | 0xc
+ | (extra->hrmode ? 1 : 0);
+ HRTFTC_HRCON
+ = ((extra->clsen ? 1 : 0) << 1)
+ | ((extra->spsen ? 1 : 0) << 0);
+ HRTFTC_HRTIMING1
+ = (extra->pcdel << 8)
+ | (extra->revdel << 4)
+ | (extra->lpdel << 0);
+ HRTFTC_HRTIMING2
+ = (extra->spldel << 9)
+ | (extra->pc2del << 0);
+ }
+ else
+ HRTFTC_HRSETUP
+ = (1 << 13)
+ | 0xc;
+#endif
+
+#if defined (CONFIG_ARCH_LH7A404)
+
+ if (extra) {
+ ALI_SETUP
+ = (1 << 13)
+ | ((fb->fb.var.xres - 1) << 4)
+ | 0xc
+ | (extra->hrmode ? 1 : 0);
+ ALI_CONTROL
+ = ((extra->clsen ? 1 : 0) << 1)
+ | ((extra->spsen ? 1 : 0) << 0);
+ ALI_TIMING1
+ = (extra->pcdel << 8)
+ | (extra->revdel << 4)
+ | (extra->lpdel << 0);
+ ALI_TIMING2
+ = (extra->spldel << 9)
+ | (extra->pc2del << 0);
+ }
+ else
+ ALI_SETUP
+ = (1 << 13)
+ | 0xc;
+#endif
+
+}
+
+#define FRAMESIZE(s) (((s) + PAGE_SIZE - 1)&PAGE_MASK)
+
+static int lh7a40x_clcd_setup (struct clcd_fb *fb)
+{
+ dma_addr_t dma;
+ u32 len = FRAMESIZE (lcd_panel.mode.xres*lcd_panel.mode.yres
+ *(lcd_panel.bpp/8));
+
+ fb->panel = &lcd_panel;
+
+ /* Enforce the sync polarity defaults */
+ if (!(fb->panel->tim2 & TIM2_IHS))
+ fb->fb.var.sync |= FB_SYNC_HOR_HIGH_ACT;
+ if (!(fb->panel->tim2 & TIM2_IVS))
+ fb->fb.var.sync |= FB_SYNC_VERT_HIGH_ACT;
+
+#if defined (HAS_LCD_PANEL_EXTRA)
+ fb->board_data = &lcd_panel_extra;
+#endif
+
+ fb->fb.screen_base
+ = dma_alloc_writecombine (&fb->dev->dev, len,
+ &dma, GFP_KERNEL);
+ printk ("CLCD: LCD setup fb virt 0x%p phys 0x%p l %x io 0x%p \n",
+ fb->fb.screen_base, (void*) dma, len,
+ (void*) io_p2v (CLCDC_PHYS));
+ printk ("CLCD: pixclock %d\n", lcd_panel.mode.pixclock);
+
+ if (!fb->fb.screen_base) {
+ printk(KERN_ERR "CLCD: unable to map framebuffer\n");
+ return -ENOMEM;
+ }
+
+#if defined (USE_RGB555)
+ fb->fb.var.green.length = 5; /* Panel uses RGB 5:5:5 */
+#endif
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = len;
+
+ /* Drive PE4 high to prevent CPLD crash */
+ GPIO_PEDD |= (1<<4);
+ GPIO_PED |= (1<<4);
+
+ GPIO_PINMUX |= (1<<1) | (1<<0); /* LCDVD[15:4] */
+
+// fb->fb.fbops->fb_check_var (&fb->fb.var, &fb->fb);
+// fb->fb.fbops->fb_set_par (&fb->fb);
+
+ return 0;
+}
+
+static int lh7a40x_clcd_mmap (struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ return dma_mmap_writecombine(&fb->dev->dev, vma,
+ fb->fb.screen_base,
+ fb->fb.fix.smem_start,
+ fb->fb.fix.smem_len);
+}
+
+static void lh7a40x_clcd_remove (struct clcd_fb *fb)
+{
+ dma_free_writecombine (&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+static struct clcd_board clcd_platform_data = {
+ .name = "lh7a40x FB",
+ .check = clcdfb_check,
+ .decode = clcdfb_decode,
+ .enable = lh7a40x_clcd_enable,
+ .setup = lh7a40x_clcd_setup,
+ .mmap = lh7a40x_clcd_mmap,
+ .remove = lh7a40x_clcd_remove,
+ .disable = lh7a40x_clcd_disable,
+};
+
+#define IRQ_CLCDC (IRQ_LCDINTR)
+
+#define AMBA_DEVICE(name,busid,base,plat,pid) \
+static struct amba_device name##_device = { \
+ .dev = { \
+ .coherent_dma_mask = ~0, \
+ .bus_id = busid, \
+ .platform_data = plat, \
+ }, \
+ .res = { \
+ .start = base##_PHYS, \
+ .end = (base##_PHYS) + (4*1024) - 1, \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ .dma_mask = ~0, \
+ .irq = { IRQ_##base, }, \
+ /* .dma = base##_DMA,*/ \
+ .periphid = pid, \
+}
+
+AMBA_DEVICE(clcd, "cldc-lh7a40x", CLCDC, &clcd_platform_data, 0x41110);
+
+static struct amba_device *amba_devs[] __initdata = {
+ &clcd_device,
+};
+
+void __init lh7a40x_clcd_init (void)
+{
+ int i;
+ int result;
+ printk ("CLCD: registering amba devices\n");
+ for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
+ struct amba_device *d = amba_devs[i];
+ result = amba_device_register(d, &iomem_resource);
+ printk (" %d -> %d\n", i ,result);
+ }
+}
here and read <file:Documentation/modules.txt>. The module
will be called amba-clcd.
+choice
+
+ depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
+ prompt "LCD Panel"
+ default FB_ARMCLCD_SHARP_LQ035Q7DB02
+
+config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
+ bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
+ help
+ This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
+ color QVGA, HRTFT panel. The LogicPD device includes an
+ an integrated HRTFT controller IC.
+ The native resolution is 240x320.
+
+config FB_ARMCLCD_SHARP_LQ057Q3DC02
+ bool "LogicPD LCD 5.7\" QVGA"
+ help
+ This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
+ color QVGA, TFT panel. The LogicPD device includes an
+ The native resolution is 320x240.
+
+config FB_ARMCLCD_SHARP_LQ64D343
+ bool "LogicPD LCD 6.4\" VGA"
+ help
+ This is an implementation of the Sharp LQ64D343, a 6.4"
+ color VGA, TFT panel. The LogicPD device includes an
+ The native resolution is 640x480.
+
+config FB_ARMCLCD_SHARP_LQ10D368
+ bool "LogicPD LCD 10.4\" VGA"
+ help
+ This is an implementation of the Sharp LQ10D368, a 10.4"
+ color VGA, TFT panel. The LogicPD device includes an
+ The native resolution is 640x480.
+
+
+config FB_ARMCLCD_SHARP_LQ121S1DG41
+ bool "LogicPD LCD 12.1\" SVGA"
+ help
+ This is an implementation of the Sharp LQ121S1DG41, a 12.1"
+ color SVGA, TFT panel. The LogicPD device includes an
+ The native resolution is 800x600.
+
+ This panel requires a clock rate may be an integer fraction
+ of the base LCDCLK frequency. The driver will select the
+ highest frequency available that is lower than the maximum
+ allowed. The panel may flicker if the clock rate is
+ slower than the recommended minimum.
+
+config FB_ARMCLCD_AUO_A070VW01_WIDE
+ bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
+ help
+ This is an implementation of the AU Optronics, a 7.0"
+ WIDE Color. The native resolution is 234x480.
+
+config FB_ARMCLCD_HITACHI
+ bool "Hitachi Wide Screen 800x480"
+ help
+ This is an implementation of the Hitachi 800x480.
+
+endchoice
+
+
config FB_ACORN
bool "Acorn VIDC support"
depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500)
projects / linux-2.6-omap-h63xx.git / commitdiff