/ getpagesize();
p = get_pages(pages);
+ /* Initialize the virtqueue */
+ vq->next = NULL;
+ vq->last_avail_idx = 0;
+ vq->dev = dev;
+
/* Initialize the configuration. */
vq->config.num = num_descs;
vq->config.irq = devices.next_irq++;
for (i = &dev->vq; *i; i = &(*i)->next);
*i = vq;
- /* Link virtqueue back to device. */
- vq->dev = dev;
-
/* Set the routine to call when the Guest does something to this
* virtqueue. */
vq->handle_output = handle_output;
dev->desc = new_dev_desc(type);
dev->handle_input = handle_input;
dev->name = name;
+ dev->vq = NULL;
return dev;
}
('port'). Once you have done that, you will be able to use
parport_claim and parport_release in order to use the port.
+The ('name') argument is the name of the device that appears in /proc
+filesystem. The string must be valid for the whole lifetime of the
+device (until parport_unregister_device is called).
+
This function will register three callbacks into your driver:
'preempt', 'wakeup' and 'irq'. Each of these may be NULL in order to
indicate that you do not want a callback.
MAC addresses passed by the firmware when no information other
than indices is available to associate an address with a device.
- phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "tbi",
- or "rtbi".
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+ Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+ "tbi", or "rtbi".
Example:
ucc@2000 {
ThinkPad ACPI Extras Driver
- Version 0.16
- August 2nd, 2007
+ Version 0.17
+ October 04th, 2007
Borislav Deianov <borislav@users.sf.net>
Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This feature allows software control of the LCD brightness on ThinkPad
models which don't have a hardware brightness slider.
-It has some limitations: the LCD backlight cannot be actually turned on or off
-by this interface, and in many ThinkPad models, the "dim while on battery"
-functionality will be enabled by the BIOS when this interface is used, and
-cannot be controlled.
-
-The backlight control has eight levels, ranging from 0 to 7. Some of the
-levels may not be distinct.
-
-There are two interfaces to the firmware for brightness control, EC and CMOS.
-To select which one should be used, use the brightness_mode module parameter:
-brightness_mode=1 selects EC mode, brightness_mode=2 selects CMOS mode,
-brightness_mode=3 selects both EC and CMOS. The driver tries to autodetect
-which interface to use.
+It has some limitations: the LCD backlight cannot be actually turned on or
+off by this interface, and in many ThinkPad models, the "dim while on
+battery" functionality will be enabled by the BIOS when this interface is
+used, and cannot be controlled.
+
+On IBM (and some of the earlier Lenovo) ThinkPads, the backlight control
+has eight brightness levels, ranging from 0 to 7. Some of the levels
+may not be distinct. Later Lenovo models that implement the ACPI
+display backlight brightness control methods have 16 levels, ranging
+from 0 to 15.
+
+There are two interfaces to the firmware for direct brightness control,
+EC and CMOS. To select which one should be used, use the
+brightness_mode module parameter: brightness_mode=1 selects EC mode,
+brightness_mode=2 selects CMOS mode, brightness_mode=3 selects both EC
+and CMOS. The driver tries to autodetect which interface to use.
+
+When display backlight brightness controls are available through the
+standard ACPI interface, it is best to use it instead of this direct
+ThinkPad-specific interface. The driver will disable its native
+backlight brightness control interface if it detects that the standard
+ACPI interface is available in the ThinkPad.
+
+The brightness_enable module parameter can be used to control whether
+the LCD brightness control feature will be enabled when available.
+brightness_enable=0 forces it to be disabled. brightness_enable=1
+forces it to be enabled when available, even if the standard ACPI
+interface is also available.
Procfs notes:
Sysfs notes:
-The interface is implemented through the backlight sysfs class, which is poorly
-documented at this time.
+The interface is implemented through the backlight sysfs class, which is
+poorly documented at this time.
-Locate the thinkpad_screen device under /sys/class/backlight, and inside it
-there will be the following attributes:
+Locate the thinkpad_screen device under /sys/class/backlight, and inside
+it there will be the following attributes:
max_brightness:
Reads the maximum brightness the hardware can be set to.
Reads what brightness the screen is set to at this instant.
brightness:
- Writes request the driver to change brightness to the given
- value. Reads will tell you what brightness the driver is trying
- to set the display to when "power" is set to zero and the display
- has not been dimmed by a kernel power management event.
+ Writes request the driver to change brightness to the
+ given value. Reads will tell you what brightness the
+ driver is trying to set the display to when "power" is set
+ to zero and the display has not been dimmed by a kernel
+ power management event.
power:
- power management mode, where 0 is "display on", and 1 to 3 will
- dim the display backlight to brightness level 0 because
- thinkpad-acpi cannot really turn the backlight off. Kernel
- power management events can temporarily increase the current
- power management level, i.e. they can dim the display.
+ power management mode, where 0 is "display on", and 1 to 3
+ will dim the display backlight to brightness level 0
+ because thinkpad-acpi cannot really turn the backlight
+ off. Kernel power management events can temporarily
+ increase the current power management level, i.e. they can
+ dim the display.
Volume control -- /proc/acpi/ibm/volume
S: Maintained
IMS TWINTURBO FRAMEBUFFER DRIVER
-P: Paul Mundt
-M: lethal@chaoticdreams.org
L: linux-fbdev-devel@lists.sourceforge.net (subscribers-only)
-S: Maintained
+S: Orphan
INFINIBAND SUBSYSTEM
P: Roland Dreier
P: Joshua Thompson
M: funaho@jurai.org
W: http://www.mac.linux-m68k.org/
-L: linux-mac68k@mac.linux-m68k.org
+L: linux-m68k@lists.linux-m68k.org
S: Maintained
M68K ON HP9000/300
W: http://www.stradis.com/
S: Maintained
-SUPERH (sh)
-P: Paul Mundt
-M: lethal@linux-sh.org
-L: linuxsh-dev@lists.sourceforge.net (subscribers-only)
-W: http://www.linux-sh.org
-S: Maintained
-
-SUPERH64 (sh64)
+SUPERH
P: Paul Mundt
M: lethal@linux-sh.org
-L: linuxsh-shmedia-dev@lists.sourceforge.net
+L: linux-sh@vger.kernel.org
W: http://www.linux-sh.org
+T: git kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.git
S: Maintained
SUN3/3X
TLAN NETWORK DRIVER
P: Samuel Chessman
M: chessman@tux.org
-L: tlan-devel@lists.sourceforge.net
+L: tlan-devel@lists.sourceforge.net (subscribers-only)
W: http://sourceforge.net/projects/tlan/
S: Maintained
#include <linux/errno.h>
#include <linux/sched.h>
#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
#include "proto.h"
EXPORT_SYMBOL(dma_alloc_coherent);
int
-dma_map_sg(struct device *dev, struct scatterlist *sg, int nents,
+dma_map_sg(struct device *dev, struct scatterlist *sgl, int nents,
enum dma_data_direction direction)
{
int i;
+ struct scatterlist *sg;
- for (i = 0; i < nents; i++ ) {
+ for_each_sg(sgl, sg, nents, i) {
void *va;
- BUG_ON(!sg[i].page);
- va = page_address(sg[i].page) + sg[i].offset;
- sg_dma_address(sg + i) = (dma_addr_t)virt_to_bus(va);
- sg_dma_len(sg + i) = sg[i].length;
+ BUG_ON(!sg_page(sg));
+ va = sg_virt(sg);
+ sg_dma_address(sg) = (dma_addr_t)virt_to_bus(va);
+ sg_dma_len(sg) = sg->length;
}
return nents;
# see Documentation/kbuild/kconfig-language.txt.
#
-mainmenu "uClinux/Blackfin (w/o MMU) Kernel Configuration"
+mainmenu "Blackfin Kernel Configuration"
config MMU
bool
bool
default y
-config BFIN
- bool
- default y
-
config SEMAPHORE_SLEEPERS
bool
default y
default y
config GENERIC_IRQ_PROBE
- bool
+ bool
default y
config GENERIC_TIME
bool
default y
-config IRQCHIP_DEMUX_GPIO
- bool
- depends on (BF52x || BF53x || BF561 || BF54x)
- default y
-
source "init/Kconfig"
source "kernel/Kconfig.preempt"
help
BF544 Processor Support.
+config BF547
+ bool "BF547"
+ help
+ BF547 Processor Support.
+
config BF548
bool "BF548"
help
config BF_REV_0_0
bool "0.0"
- depends on (BF549 || BF527)
+ depends on (BF52x || BF54x)
config BF_REV_0_1
- bool "0.2"
- depends on (BF549 || BF527)
+ bool "0.1"
+ depends on (BF52x || BF54x)
config BF_REV_0_2
bool "0.2"
config BF54x
bool
- depends on (BF542 || BF544 || BF548 || BF549)
+ depends on (BF542 || BF544 || BF547 || BF548 || BF549)
default y
config BFIN_DUAL_CORE
depends on !BFIN_DUAL_CORE
default y
-choice
- prompt "System type"
- default BFIN533_STAMP
- help
- Do NOT change the board here. Please use the top level
- configuration to ensure that all the other settings are
- correct.
-
-config BFIN527_EZKIT
- bool "BF527-EZKIT"
- depends on (BF522 || BF525 || BF527)
- help
- BF533-EZKIT-LITE board Support.
-
-config BFIN533_EZKIT
- bool "BF533-EZKIT"
- depends on (BF533 || BF532 || BF531)
- help
- BF533-EZKIT-LITE board Support.
-
-config BFIN533_STAMP
- bool "BF533-STAMP"
- depends on (BF533 || BF532 || BF531)
- help
- BF533-STAMP board Support.
-
-config BFIN537_STAMP
- bool "BF537-STAMP"
- depends on (BF537 || BF536 || BF534)
- help
- BF537-STAMP board Support.
-
-config BFIN533_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF533"
- depends on (BF533)
- help
- CM-BF533 support for EVAL- and DEV-Board.
-
-config BFIN537_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF537"
- depends on (BF537)
- help
- CM-BF537 support for EVAL- and DEV-Board.
-
-config BFIN548_EZKIT
- bool "BF548-EZKIT"
- depends on (BF548 || BF549)
- help
- BFIN548-EZKIT board Support.
-
-config BFIN561_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF561"
- depends on (BF561)
- help
- CM-BF561 support for EVAL- and DEV-Board.
-
-config BFIN561_EZKIT
- bool "BF561-EZKIT"
- depends on (BF561)
- help
- BF561-EZKIT-LITE board Support.
-
-config BFIN561_TEPLA
- bool "BF561-TEPLA"
- depends on (BF561)
- help
- BF561-TEPLA board Support.
-
-config PNAV10
- bool "PNAV 1.0 board"
- depends on (BF537)
- help
- PNAV 1.0 board Support.
-
-config H8606_HVSISTEMAS
- bool "HV Sistemas H8606"
- depends on (BF532)
- help
- HV Sistemas H8606 board support.
-
-config GENERIC_BOARD
- bool "Custom"
- depends on (BF537 || BF536 \
- || BF534 || BF561 || BF535 || BF533 || BF532 || BF531)
- help
- GENERIC or Custom board Support.
-
-endchoice
-
config MEM_GENERIC_BOARD
bool
depends on GENERIC_BOARD
configuration.
config PLL_BYPASS
- bool "Bypass PLL"
- depends on BFIN_KERNEL_CLOCK
- default n
+ bool "Bypass PLL"
+ depends on BFIN_KERNEL_CLOCK
+ default n
config CLKIN_HALF
bool "Half Clock In"
default 500000000 if BF534
default 400000000 if BF536
default 600000000 if BF537
- default 533000000 if BF538
- default 533000000 if BF539
+ default 533333333 if BF538
+ default 533333333 if BF539
default 600000000 if BF542
- default 533000000 if BF544
- default 533000000 if BF549
+ default 533333333 if BF544
+ default 533333333 if BF549
default 600000000 if BF561
config MIN_VCO_HZ
config MAX_SCLK_HZ
int
- default 133000000
+ default 133333333
config MIN_SCLK_HZ
int
default 0x99B3
endmenu
+config EBIU_MBSCTLVAL
+ hex "EBIU Bank Select Control Register"
+ depends on BF54x
+ default 0
+
+config EBIU_MODEVAL
+ hex "Flash Memory Mode Control Register"
+ depends on BF54x
+ default 1
+
+config EBIU_FCTLVAL
+ hex "Flash Memory Bank Control Register"
+ depends on BF54x
+ default 6
endmenu
#############################################################################
source "kernel/Kconfig.instrumentation"
-menu "Kernel hacking"
-
-source "lib/Kconfig.debug"
-
-config DEBUG_HWERR
- bool "Hardware error interrupt debugging"
- depends on DEBUG_KERNEL
- help
- When enabled, the hardware error interrupt is never disabled, and
- will happen immediately when an error condition occurs. This comes
- at a slight cost in code size, but is necessary if you are getting
- hardware error interrupts and need to know where they are coming
- from.
-
-config DEBUG_ICACHE_CHECK
- bool "Check Instruction cache coherency"
- depends on DEBUG_KERNEL
- depends on DEBUG_HWERR
- help
- Say Y here if you are getting weird unexplained errors. This will
- ensure that icache is what SDRAM says it should be by doing a
- byte wise comparison between SDRAM and instruction cache. This
- also relocates the irq_panic() function to L1 memory, (which is
- un-cached).
-
-config DEBUG_HUNT_FOR_ZERO
- bool "Catch NULL pointer reads/writes"
- default y
- help
- Say Y here to catch reads/writes to anywhere in the memory range
- from 0x0000 - 0x0FFF (the first 4k) of memory. This is useful in
- catching common programming errors such as NULL pointer dereferences.
-
- Misbehaving applications will be killed (generate a SEGV) while the
- kernel will trigger a panic.
-
- Enabling this option will take up an extra entry in CPLB table.
- Otherwise, there is no extra overhead.
-
-config DEBUG_BFIN_HWTRACE_ON
- bool "Turn on Blackfin's Hardware Trace"
- default y
- help
- All Blackfins include a Trace Unit which stores a history of the last
- 16 changes in program flow taken by the program sequencer. The history
- allows the user to recreate the program sequencer’s recent path. This
- can be handy when an application dies - we print out the execution
- path of how it got to the offending instruction.
-
- By turning this off, you may save a tiny amount of power.
-
-choice
- prompt "Omit loop Tracing"
- default DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
- depends on DEBUG_BFIN_HWTRACE_ON
- help
- The trace buffer can be configured to omit recording of changes in
- program flow that match either the last entry or one of the last
- two entries. Omitting one of these entries from the record prevents
- the trace buffer from overflowing because of any sort of loop (for, do
- while, etc) in the program.
-
- Because zero-overhead Hardware loops are not recorded in the trace buffer,
- this feature can be used to prevent trace overflow from loops that
- are nested four deep.
-
-config DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
- bool "Trace all Loops"
- help
- The trace buffer records all changes of flow
-
-config DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
- bool "Compress single-level loops"
- help
- The trace buffer does not record single loops - helpful if trace
- is spinning on a while or do loop.
-
-config DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
- bool "Compress two-level loops"
- help
- The trace buffer does not record loops two levels deep. Helpful if
- the trace is spinning in a nested loop
-
-endchoice
-
-config DEBUG_BFIN_HWTRACE_COMPRESSION
- int
- depends on DEBUG_BFIN_HWTRACE_ON
- default 0 if DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
- default 1 if DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
- default 2 if DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
-
-
-config DEBUG_BFIN_HWTRACE_EXPAND
- bool "Expand Trace Buffer greater than 16 entries"
- depends on DEBUG_BFIN_HWTRACE_ON
- default n
- help
- By selecting this option, every time the 16 hardware entries in
- the Blackfin's HW Trace buffer are full, the kernel will move them
- into a software buffer, for dumping when there is an issue. This
- has a great impact on performance, (an interrupt every 16 change of
- flows) and should normally be turned off, except in those nasty
- debugging sessions
-
-config DEBUG_BFIN_HWTRACE_EXPAND_LEN
- int "Size of Trace buffer (in power of 2k)"
- range 0 4
- depends on DEBUG_BFIN_HWTRACE_EXPAND
- default 1
- help
- This sets the size of the software buffer that the trace information
- is kept in.
- 0 for (2^0) 1k, or 256 entries,
- 1 for (2^1) 2k, or 512 entries,
- 2 for (2^2) 4k, or 1024 entries,
- 3 for (2^3) 8k, or 2048 entries,
- 4 for (2^4) 16k, or 4096 entries
-
-config DEBUG_BFIN_NO_KERN_HWTRACE
- bool "Trace user apps (turn off hwtrace in kernel)"
- depends on DEBUG_BFIN_HWTRACE_ON
- default n
- help
- Some pieces of the kernel contain a lot of flow changes which can
- quickly fill up the hardware trace buffer. When debugging crashes,
- the hardware trace may indicate that the problem lies in kernel
- space when in reality an application is buggy.
-
- Say Y here to disable hardware tracing in some known "jumpy" pieces
- of code so that the trace buffer will extend further back.
-
-config EARLY_PRINTK
- bool "Early printk"
- default n
- help
- This option enables special console drivers which allow the kernel
- to print messages very early in the bootup process.
-
- This is useful for kernel debugging when your machine crashes very
- early before the console code is initialized. After enabling this
- feature, you must add "earlyprintk=serial,uart0,57600" to the
- command line (bootargs). It is safe to say Y here in all cases, as
- all of this lives in the init section and is thrown away after the
- kernel boots completely.
-
-config DUAL_CORE_TEST_MODULE
- tristate "Dual Core Test Module"
- depends on (BF561)
- default n
- help
- Say Y here to build-in dual core test module for dual core test.
-
-config CPLB_INFO
- bool "Display the CPLB information"
- help
- Display the CPLB information.
-
-config ACCESS_CHECK
- bool "Check the user pointer address"
- default y
- help
- Usually the pointer transfer from user space is checked to see if its
- address is in the kernel space.
-
- Say N here to disable that check to improve the performance.
-
-endmenu
+source "arch/blackfin/Kconfig.debug"
source "security/Kconfig"
--- /dev/null
+menu "Kernel hacking"
+
+source "lib/Kconfig.debug"
+
+config DEBUG_MMRS
+ bool "Generate Blackfin MMR tree"
+ select DEBUG_FS
+ help
+ Create a tree of Blackfin MMRs via the debugfs tree. If
+ you enable this, you will find all MMRs laid out in the
+ /sys/kernel/debug/blackfin/ directory where you can read/write
+ MMRs directly from userspace. This is obviously just a debug
+ feature.
+
+config DEBUG_HWERR
+ bool "Hardware error interrupt debugging"
+ depends on DEBUG_KERNEL
+ help
+ When enabled, the hardware error interrupt is never disabled, and
+ will happen immediately when an error condition occurs. This comes
+ at a slight cost in code size, but is necessary if you are getting
+ hardware error interrupts and need to know where they are coming
+ from.
+
+config DEBUG_ICACHE_CHECK
+ bool "Check Instruction cache coherency"
+ depends on DEBUG_KERNEL
+ depends on DEBUG_HWERR
+ help
+ Say Y here if you are getting weird unexplained errors. This will
+ ensure that icache is what SDRAM says it should be by doing a
+ byte wise comparison between SDRAM and instruction cache. This
+ also relocates the irq_panic() function to L1 memory, (which is
+ un-cached).
+
+config DEBUG_HUNT_FOR_ZERO
+ bool "Catch NULL pointer reads/writes"
+ default y
+ help
+ Say Y here to catch reads/writes to anywhere in the memory range
+ from 0x0000 - 0x0FFF (the first 4k) of memory. This is useful in
+ catching common programming errors such as NULL pointer dereferences.
+
+ Misbehaving applications will be killed (generate a SEGV) while the
+ kernel will trigger a panic.
+
+ Enabling this option will take up an extra entry in CPLB table.
+ Otherwise, there is no extra overhead.
+
+config DEBUG_BFIN_HWTRACE_ON
+ bool "Turn on Blackfin's Hardware Trace"
+ default y
+ help
+ All Blackfins include a Trace Unit which stores a history of the last
+ 16 changes in program flow taken by the program sequencer. The history
+ allows the user to recreate the program sequencer’s recent path. This
+ can be handy when an application dies - we print out the execution
+ path of how it got to the offending instruction.
+
+ By turning this off, you may save a tiny amount of power.
+
+choice
+ prompt "Omit loop Tracing"
+ default DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ depends on DEBUG_BFIN_HWTRACE_ON
+ help
+ The trace buffer can be configured to omit recording of changes in
+ program flow that match either the last entry or one of the last
+ two entries. Omitting one of these entries from the record prevents
+ the trace buffer from overflowing because of any sort of loop (for, do
+ while, etc) in the program.
+
+ Because zero-overhead Hardware loops are not recorded in the trace buffer,
+ this feature can be used to prevent trace overflow from loops that
+ are nested four deep.
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ bool "Trace all Loops"
+ help
+ The trace buffer records all changes of flow
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
+ bool "Compress single-level loops"
+ help
+ The trace buffer does not record single loops - helpful if trace
+ is spinning on a while or do loop.
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
+ bool "Compress two-level loops"
+ help
+ The trace buffer does not record loops two levels deep. Helpful if
+ the trace is spinning in a nested loop
+
+endchoice
+
+config DEBUG_BFIN_HWTRACE_COMPRESSION
+ int
+ depends on DEBUG_BFIN_HWTRACE_ON
+ default 0 if DEBUG_BFIN_HWTRACE_COMPRESSION_OFF
+ default 1 if DEBUG_BFIN_HWTRACE_COMPRESSION_ONE
+ default 2 if DEBUG_BFIN_HWTRACE_COMPRESSION_TWO
+
+
+config DEBUG_BFIN_HWTRACE_EXPAND
+ bool "Expand Trace Buffer greater than 16 entries"
+ depends on DEBUG_BFIN_HWTRACE_ON
+ default n
+ help
+ By selecting this option, every time the 16 hardware entries in
+ the Blackfin's HW Trace buffer are full, the kernel will move them
+ into a software buffer, for dumping when there is an issue. This
+ has a great impact on performance, (an interrupt every 16 change of
+ flows) and should normally be turned off, except in those nasty
+ debugging sessions
+
+config DEBUG_BFIN_HWTRACE_EXPAND_LEN
+ int "Size of Trace buffer (in power of 2k)"
+ range 0 4
+ depends on DEBUG_BFIN_HWTRACE_EXPAND
+ default 1
+ help
+ This sets the size of the software buffer that the trace information
+ is kept in.
+ 0 for (2^0) 1k, or 256 entries,
+ 1 for (2^1) 2k, or 512 entries,
+ 2 for (2^2) 4k, or 1024 entries,
+ 3 for (2^3) 8k, or 2048 entries,
+ 4 for (2^4) 16k, or 4096 entries
+
+config DEBUG_BFIN_NO_KERN_HWTRACE
+ bool "Trace user apps (turn off hwtrace in kernel)"
+ depends on DEBUG_BFIN_HWTRACE_ON
+ default n
+ help
+ Some pieces of the kernel contain a lot of flow changes which can
+ quickly fill up the hardware trace buffer. When debugging crashes,
+ the hardware trace may indicate that the problem lies in kernel
+ space when in reality an application is buggy.
+
+ Say Y here to disable hardware tracing in some known "jumpy" pieces
+ of code so that the trace buffer will extend further back.
+
+config EARLY_PRINTK
+ bool "Early printk"
+ default n
+ help
+ This option enables special console drivers which allow the kernel
+ to print messages very early in the bootup process.
+
+ This is useful for kernel debugging when your machine crashes very
+ early before the console code is initialized. After enabling this
+ feature, you must add "earlyprintk=serial,uart0,57600" to the
+ command line (bootargs). It is safe to say Y here in all cases, as
+ all of this lives in the init section and is thrown away after the
+ kernel boots completely.
+
+config DUAL_CORE_TEST_MODULE
+ tristate "Dual Core Test Module"
+ depends on (BF561)
+ default n
+ help
+ Say Y here to build-in dual core test module for dual core test.
+
+config CPLB_INFO
+ bool "Display the CPLB information"
+ help
+ Display the CPLB information.
+
+config ACCESS_CHECK
+ bool "Check the user pointer address"
+ default y
+ help
+ Usually the pointer transfer from user space is checked to see if its
+ address is in the kernel space.
+
+ Say N here to disable that check to improve the performance.
+
+endmenu
machine-$(CONFIG_BF537) := bf537
machine-$(CONFIG_BF542) := bf548
machine-$(CONFIG_BF544) := bf548
+machine-$(CONFIG_BF547) := bf548
machine-$(CONFIG_BF548) := bf548
machine-$(CONFIG_BF549) := bf548
machine-$(CONFIG_BF561) := bf561
cpu-$(CONFIG_BF537) := bf537
cpu-$(CONFIG_BF542) := bf542
cpu-$(CONFIG_BF544) := bf544
+cpu-$(CONFIG_BF547) := bf547
cpu-$(CONFIG_BF548) := bf548
cpu-$(CONFIG_BF549) := bf549
cpu-$(CONFIG_BF561) := bf561
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.9
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# CONFIG_BF537 is not set
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
# CONFIG_BF561 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF52x=y
CONFIG_BFIN_SINGLE_CORE=y
-CONFIG_BFIN527_EZKIT=y
-# CONFIG_BFIN533_EZKIT is not set
-# CONFIG_BFIN533_STAMP is not set
-# CONFIG_BFIN537_STAMP is not set
-# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_GENERIC_BOARD is not set
CONFIG_MEM_MT48LC32M16A2TG_75=y
+CONFIG_BFIN527_EZKIT=y
#
# BF527 Specific Configuration
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=600000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
CONFIG_BFIN_NAND_ALE=1
CONFIG_BFIN_NAND_READY=3
CONFIG_MTD_NAND_IDS=m
+# CONFIG_MTD_NAND_BF5XX is not set
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
# CONFIG_SPI_ADC_BF533 is not set
# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
# CONFIG_BFIN_SPORT is not set
# CONFIG_BFIN_TIMER_LATENCY is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.6
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
#
# Processor and Board Settings
#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
# CONFIG_BF531 is not set
# CONFIG_BF532 is not set
CONFIG_BF533=y
# CONFIG_BF537 is not set
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
# CONFIG_BF561 is not set
# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
# CONFIG_BF_REV_0_2 is not set
CONFIG_BF_REV_0_3=y
# CONFIG_BF_REV_0_4 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF53x=y
CONFIG_BFIN_SINGLE_CORE=y
+CONFIG_MEM_MT48LC16M16A2TG_75=y
CONFIG_BFIN533_EZKIT=y
# CONFIG_BFIN533_STAMP is not set
-# CONFIG_BFIN537_STAMP is not set
# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_GENERIC_BOARD is not set
-CONFIG_MEM_MT48LC16M16A2TG_75=y
+# CONFIG_H8606_HVSISTEMAS is not set
+# CONFIG_GENERIC_BF533_BOARD is not set
#
# BF533/2/1 Specific Configuration
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=750000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
CONFIG_MTD_BF5xx=m
CONFIG_BFIN_FLASH_SIZE=0x400000
CONFIG_EBIU_FLASH_BASE=0x20000000
-
-#
-# FLASH_EBIU_AMBCTL Control
-#
-CONFIG_BFIN_FLASH_BANK_0=0x7BB0
-CONFIG_BFIN_FLASH_BANK_1=0x7BB0
-CONFIG_BFIN_FLASH_BANK_2=0x7BB0
-CONFIG_BFIN_FLASH_BANK_3=0x7BB0
# CONFIG_MTD_UCLINUX is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BFIN_PFLAGS is not set
+# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
CONFIG_BFIN_SPORT=y
# CONFIG_BFIN_TIMER_LATENCY is not set
# CONFIG_SERIAL_BFIN_PIO is not set
CONFIG_SERIAL_BFIN_UART0=y
# CONFIG_BFIN_UART0_CTSRTS is not set
+# CONFIG_SERIAL_BFIN_UART1 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_BFIN_SPORT is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.6
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
#
# Processor and Board Settings
#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
# CONFIG_BF531 is not set
# CONFIG_BF532 is not set
CONFIG_BF533=y
# CONFIG_BF537 is not set
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
# CONFIG_BF561 is not set
# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
# CONFIG_BF_REV_0_2 is not set
CONFIG_BF_REV_0_3=y
# CONFIG_BF_REV_0_4 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF53x=y
CONFIG_BFIN_SINGLE_CORE=y
+CONFIG_MEM_MT48LC64M4A2FB_7E=y
+CONFIG_BFIN_SHARED_FLASH_ENET=y
# CONFIG_BFIN533_EZKIT is not set
CONFIG_BFIN533_STAMP=y
-# CONFIG_BFIN537_STAMP is not set
# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_GENERIC_BOARD is not set
-CONFIG_MEM_MT48LC64M4A2FB_7E=y
-CONFIG_BFIN_SHARED_FLASH_ENET=y
+# CONFIG_H8606_HVSISTEMAS is not set
+# CONFIG_GENERIC_BF533_BOARD is not set
#
# BF533/2/1 Specific Configuration
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=750000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BFIN_PFLAGS is not set
+# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
CONFIG_BFIN_SPORT=y
# CONFIG_BFIN_TIMER_LATENCY is not set
# CONFIG_SERIAL_BFIN_PIO is not set
CONFIG_SERIAL_BFIN_UART0=y
# CONFIG_BFIN_UART0_CTSRTS is not set
+# CONFIG_SERIAL_BFIN_UART1 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_BFIN_SPORT is not set
# CONFIG_PAL_YCBCR is not set
CONFIG_ADV7393_1XMEM=y
# CONFIG_ADV7393_2XMEM is not set
+# CONFIG_FB_BFIN_T350MCQB is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_LOGO is not set
#
# CONFIG_SND_SOC is not set
-#
-# SoC Audio for the ADI Blackfin
-#
-# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
-
#
# Open Sound System
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.6
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
#
# Processor and Board Settings
#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
# CONFIG_BF531 is not set
# CONFIG_BF532 is not set
# CONFIG_BF533 is not set
CONFIG_BF537=y
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
# CONFIG_BF561 is not set
# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
CONFIG_BF_REV_0_2=y
# CONFIG_BF_REV_0_3 is not set
# CONFIG_BF_REV_0_4 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF53x=y
CONFIG_BFIN_SINGLE_CORE=y
-# CONFIG_BFIN533_EZKIT is not set
-# CONFIG_BFIN533_STAMP is not set
-CONFIG_BFIN537_STAMP=y
-# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_GENERIC_BOARD is not set
CONFIG_MEM_MT48LC32M8A2_75=y
CONFIG_IRQ_PLL_WAKEUP=7
-
-#
-# BF537 Specific Configuration
-#
-
-#
-# Interrupt Priority Assignment
-#
-
-#
-# Priority
-#
-CONFIG_IRQ_DMA_ERROR=7
-CONFIG_IRQ_ERROR=7
CONFIG_IRQ_RTC=8
CONFIG_IRQ_PPI=8
CONFIG_IRQ_SPORT0_RX=9
CONFIG_IRQ_UART0_TX=10
CONFIG_IRQ_UART1_RX=10
CONFIG_IRQ_UART1_TX=10
-CONFIG_IRQ_CAN_RX=11
-CONFIG_IRQ_CAN_TX=11
CONFIG_IRQ_MAC_RX=11
CONFIG_IRQ_MAC_TX=11
CONFIG_IRQ_TMR0=12
CONFIG_IRQ_TMR5=12
CONFIG_IRQ_TMR6=12
CONFIG_IRQ_TMR7=12
-CONFIG_IRQ_PROG_INTA=12
CONFIG_IRQ_PORTG_INTB=12
CONFIG_IRQ_MEM_DMA0=13
CONFIG_IRQ_MEM_DMA1=13
CONFIG_IRQ_WATCH=13
+CONFIG_BFIN537_STAMP=y
+# CONFIG_BFIN537_BLUETECHNIX_CM is not set
+# CONFIG_PNAV10 is not set
+# CONFIG_GENERIC_BF537_BOARD is not set
+
+#
+# BF537 Specific Configuration
+#
+
+#
+# Interrupt Priority Assignment
+#
+
+#
+# Priority
+#
+CONFIG_IRQ_DMA_ERROR=7
+CONFIG_IRQ_ERROR=7
+CONFIG_IRQ_CAN_RX=11
+CONFIG_IRQ_CAN_TX=11
+CONFIG_IRQ_PROG_INTA=12
#
# Board customizations
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=600000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
CONFIG_MTD_BF5xx=m
CONFIG_BFIN_FLASH_SIZE=0x400000
CONFIG_EBIU_FLASH_BASE=0x20000000
-
-#
-# FLASH_EBIU_AMBCTL Control
-#
-CONFIG_BFIN_FLASH_BANK_0=0x7BB0
-CONFIG_BFIN_FLASH_BANK_1=0x7BB0
-CONFIG_BFIN_FLASH_BANK_2=0x7BB0
-CONFIG_BFIN_FLASH_BANK_3=0x7BB0
# CONFIG_MTD_UCLINUX is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BFIN_PFLAGS is not set
+# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
CONFIG_BFIN_SPORT=y
# CONFIG_BFIN_TIMER_LATENCY is not set
CONFIG_LQ035_SLAVE_ADDR=0x58
# CONFIG_FB_BFIN_LANDSCAPE is not set
# CONFIG_FB_BFIN_BGR is not set
+# CONFIG_FB_BFIN_T350MCQB is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_LOGO is not set
#
# CONFIG_SND_SOC is not set
-#
-# SoC Audio for the ADI Blackfin
-#
-# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
-
#
# Open Sound System
#
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.10
-# Sat Oct 27 02:34:07 2007
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# CONFIG_BF537 is not set
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
CONFIG_BF549=y
# CONFIG_BF561 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF54x=y
CONFIG_BFIN_SINGLE_CORE=y
-# CONFIG_BFIN527_EZKIT is not set
-# CONFIG_BFIN533_EZKIT is not set
-# CONFIG_BFIN533_STAMP is not set
-# CONFIG_BFIN537_STAMP is not set
-# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-CONFIG_BFIN548_EZKIT=y
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_H8606_HVSISTEMAS is not set
-# CONFIG_GENERIC_BOARD is not set
CONFIG_IRQ_PLL_WAKEUP=7
CONFIG_IRQ_RTC=8
CONFIG_IRQ_SPORT0_RX=9
CONFIG_IRQ_TIMER8=11
CONFIG_IRQ_TIMER9=11
CONFIG_IRQ_TIMER10=11
+CONFIG_BFIN548_EZKIT=y
#
# BF548 Specific Configuration
#
CONFIG_CLKIN_HZ=25000000
# CONFIG_BFIN_KERNEL_CLOCK is not set
-CONFIG_MAX_VCO_HZ=533333333
+CONFIG_MAX_VCO_HZ=533000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
CONFIG_BANK_1=0x5554
CONFIG_BANK_2=0x7BB0
CONFIG_BANK_3=0x99B3
+CONFIG_EBUI_MBSCTLVAL=0x0
+CONFIG_EBUI_MODEVAL=0x1
+CONFIG_EBUI_FCTLVAL=0x6
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
CONFIG_SND_BF5XX_SOC=y
CONFIG_SND_BF5XX_SOC_AC97=y
CONFIG_SND_BF5XX_SOC_BF548_EZKIT=y
+# CONFIG_SND_BF5XX_SOC_WM8750 is not set
+# CONFIG_SND_BF5XX_SOC_WM8731 is not set
CONFIG_SND_BF5XX_SPORT_NUM=0
# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
CONFIG_SND_SOC_AD1980=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.6
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
#
# Processor and Board Settings
#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
# CONFIG_BF531 is not set
# CONFIG_BF532 is not set
# CONFIG_BF533 is not set
# CONFIG_BF537 is not set
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
CONFIG_BF561=y
# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
# CONFIG_BF_REV_0_2 is not set
CONFIG_BF_REV_0_3=y
# CONFIG_BF_REV_0_4 is not set
# CONFIG_BF_REV_ANY is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BFIN_DUAL_CORE=y
-# CONFIG_BFIN533_EZKIT is not set
-# CONFIG_BFIN533_STAMP is not set
-# CONFIG_BFIN537_STAMP is not set
-# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
+CONFIG_MEM_MT48LC16M16A2TG_75=y
+CONFIG_IRQ_PLL_WAKEUP=7
+CONFIG_IRQ_SPORT0_ERROR=7
+CONFIG_IRQ_SPORT1_ERROR=7
+CONFIG_IRQ_SPI_ERROR=7
CONFIG_BFIN561_EZKIT=y
# CONFIG_BFIN561_TEPLA is not set
-# CONFIG_PNAV10 is not set
-# CONFIG_GENERIC_BOARD is not set
-CONFIG_MEM_MT48LC16M16A2TG_75=y
+# CONFIG_BFIN561_BLUETECHNIX_CM is not set
+# CONFIG_GENERIC_BF561_BOARD is not set
#
# BF561 Specific Configuration
#
# Priority
#
-CONFIG_IRQ_PLL_WAKEUP=7
CONFIG_IRQ_DMA1_ERROR=7
CONFIG_IRQ_DMA2_ERROR=7
CONFIG_IRQ_IMDMA_ERROR=7
CONFIG_IRQ_PPI0_ERROR=7
CONFIG_IRQ_PPI1_ERROR=7
-CONFIG_IRQ_SPORT0_ERROR=7
-CONFIG_IRQ_SPORT1_ERROR=7
-CONFIG_IRQ_SPI_ERROR=7
CONFIG_IRQ_UART_ERROR=7
CONFIG_IRQ_RESERVED_ERROR=7
CONFIG_IRQ_DMA1_0=8
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=600000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
CONFIG_MTD_BF5xx=m
CONFIG_BFIN_FLASH_SIZE=0x0400000
CONFIG_EBIU_FLASH_BASE=0x20000000
-
-#
-# FLASH_EBIU_AMBCTL Control
-#
-CONFIG_BFIN_FLASH_BANK_0=0x7BB0
-CONFIG_BFIN_FLASH_BANK_1=0x7BB0
-CONFIG_BFIN_FLASH_BANK_2=0x7BB0
-CONFIG_BFIN_FLASH_BANK_3=0x7BB0
# CONFIG_MTD_UCLINUX is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BFIN_PFLAGS is not set
+# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
# CONFIG_BFIN_SPORT is not set
# CONFIG_BFIN_TIMER_LATENCY is not set
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.22.12
+#
+# CONFIG_MMU is not set
+# CONFIG_FPU is not set
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
+CONFIG_BLACKFIN=y
+CONFIG_ZONE_DMA=y
+CONFIG_SEMAPHORE_SLEEPERS=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_GPIO=y
+CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
+# CONFIG_NP2 is not set
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+CONFIG_TINY_SHMEM=y
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+
+#
+# Blackfin Processor Options
+#
+
+#
+# Processor and Board Settings
+#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
+# CONFIG_BF531 is not set
+CONFIG_BF532=y
+# CONFIG_BF533 is not set
+# CONFIG_BF534 is not set
+# CONFIG_BF536 is not set
+# CONFIG_BF537 is not set
+# CONFIG_BF542 is not set
+# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
+# CONFIG_BF548 is not set
+# CONFIG_BF549 is not set
+# CONFIG_BF561 is not set
+# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
+# CONFIG_BF_REV_0_2 is not set
+# CONFIG_BF_REV_0_3 is not set
+# CONFIG_BF_REV_0_4 is not set
+CONFIG_BF_REV_0_5=y
+# CONFIG_BF_REV_ANY is not set
+# CONFIG_BF_REV_NONE is not set
+CONFIG_BF53x=y
+CONFIG_BFIN_SINGLE_CORE=y
+CONFIG_MEM_MT48LC16M16A2TG_75=y
+# CONFIG_BFIN533_EZKIT is not set
+# CONFIG_BFIN533_STAMP is not set
+# CONFIG_BFIN533_BLUETECHNIX_CM is not set
+CONFIG_H8606_HVSISTEMAS=y
+# CONFIG_GENERIC_BF533_BOARD is not set
+
+#
+# BF533/2/1 Specific Configuration
+#
+
+#
+# Interrupt Priority Assignment
+#
+
+#
+# Priority
+#
+CONFIG_UART_ERROR=7
+CONFIG_SPORT0_ERROR=7
+CONFIG_SPI_ERROR=7
+CONFIG_SPORT1_ERROR=7
+CONFIG_PPI_ERROR=7
+CONFIG_DMA_ERROR=7
+CONFIG_PLLWAKE_ERROR=7
+CONFIG_RTC_ERROR=8
+CONFIG_DMA0_PPI=8
+CONFIG_DMA1_SPORT0RX=9
+CONFIG_DMA2_SPORT0TX=9
+CONFIG_DMA3_SPORT1RX=9
+CONFIG_DMA4_SPORT1TX=9
+CONFIG_DMA5_SPI=10
+CONFIG_DMA6_UARTRX=10
+CONFIG_DMA7_UARTTX=10
+CONFIG_TIMER0=11
+CONFIG_TIMER1=11
+CONFIG_TIMER2=11
+CONFIG_PFA=12
+CONFIG_PFB=12
+CONFIG_MEMDMA0=13
+CONFIG_MEMDMA1=13
+CONFIG_WDTIMER=13
+
+#
+# Board customizations
+#
+# CONFIG_CMDLINE_BOOL is not set
+
+#
+# Clock/PLL Setup
+#
+CONFIG_CLKIN_HZ=25000000
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=400000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133000000
+CONFIG_MIN_SCLK_HZ=27000000
+
+#
+# Kernel Timer/Scheduler
+#
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+
+#
+# Memory Setup
+#
+CONFIG_MEM_SIZE=32
+CONFIG_MEM_ADD_WIDTH=9
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
+#
+# Memory Optimizations
+#
+CONFIG_I_ENTRY_L1=y
+CONFIG_EXCPT_IRQ_SYSC_L1=y
+CONFIG_DO_IRQ_L1=y
+CONFIG_CORE_TIMER_IRQ_L1=y
+CONFIG_IDLE_L1=y
+CONFIG_SCHEDULE_L1=y
+CONFIG_ARITHMETIC_OPS_L1=y
+CONFIG_ACCESS_OK_L1=y
+CONFIG_MEMSET_L1=y
+CONFIG_MEMCPY_L1=y
+CONFIG_SYS_BFIN_SPINLOCK_L1=y
+# CONFIG_IP_CHECKSUM_L1 is not set
+# CONFIG_CACHELINE_ALIGNED_L1 is not set
+# CONFIG_SYSCALL_TAB_L1 is not set
+# CONFIG_CPLB_SWITCH_TAB_L1 is not set
+CONFIG_RAMKERNEL=y
+# CONFIG_ROMKERNEL is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_LARGE_ALLOCS=y
+CONFIG_BFIN_GPTIMERS=y
+CONFIG_BFIN_DMA_5XX=y
+# CONFIG_DMA_UNCACHED_2M is not set
+CONFIG_DMA_UNCACHED_1M=y
+# CONFIG_DMA_UNCACHED_NONE is not set
+
+#
+# Cache Support
+#
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+CONFIG_BFIN_ICACHE_LOCK=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
+CONFIG_L1_MAX_PIECE=16
+
+#
+# Asynchonous Memory Configuration
+#
+
+#
+# EBIU_AMGCTL Global Control
+#
+CONFIG_C_AMCKEN=y
+CONFIG_C_CDPRIO=y
+# CONFIG_C_AMBEN is not set
+# CONFIG_C_AMBEN_B0 is not set
+# CONFIG_C_AMBEN_B0_B1 is not set
+# CONFIG_C_AMBEN_B0_B1_B2 is not set
+CONFIG_C_AMBEN_ALL=y
+
+#
+# EBIU_AMBCTL Control
+#
+CONFIG_BANK_0=0x7BB0
+CONFIG_BANK_1=0x7BB0
+CONFIG_BANK_2=0x7BB0
+CONFIG_BANK_3=0x99B3
+
+#
+# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
+#
+# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF_FDPIC=y
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+# CONFIG_BINFMT_SHARED_FLAT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+CONFIG_PM=y
+CONFIG_PM_LEGACY=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_PM_SYSFS_DEPRECATED is not set
+CONFIG_PM_WAKEUP_GPIO_BY_SIC_IWR=y
+# CONFIG_PM_WAKEUP_BY_GPIO is not set
+# CONFIG_PM_WAKEUP_GPIO_API is not set
+CONFIG_PM_WAKEUP_SIC_IWR=0x100000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETLABEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+CONFIG_IRDA=m
+
+#
+# IrDA protocols
+#
+CONFIG_IRLAN=m
+CONFIG_IRCOMM=m
+# CONFIG_IRDA_ULTRA is not set
+
+#
+# IrDA options
+#
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+# CONFIG_IRDA_FAST_RR is not set
+# CONFIG_IRDA_DEBUG is not set
+
+#
+# Infrared-port device drivers
+#
+
+#
+# SIR device drivers
+#
+CONFIG_IRTTY_SIR=m
+
+#
+# Dongle support
+#
+# CONFIG_DONGLE is not set
+
+#
+# Old SIR device drivers
+#
+# CONFIG_IRPORT_SIR is not set
+
+#
+# Old Serial dongle support
+#
+
+#
+# FIR device drivers
+#
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_BF5xx is not set
+# CONFIG_MTD_UCLINUX is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+CONFIG_MTD_M25P80=y
+CONFIG_M25PXX_USE_FAST_READ=y
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_SMC91X is not set
+# CONFIG_SMSC911X is not set
+CONFIG_DM9000=y
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+CONFIG_INPUT_EVDEV=m
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_UINPUT is not set
+# CONFIG_BF53X_PFBUTTONS is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_AD9960 is not set
+# CONFIG_SPI_ADC_BF533 is not set
+CONFIG_BF5xx_PFLAGS=y
+# CONFIG_BF5xx_PFLAGS_PROC is not set
+# CONFIG_BF5xx_PPIFCD is not set
+CONFIG_BFIN_SIMPLE_TIMER=y
+# CONFIG_BF5xx_PPI is not set
+CONFIG_BFIN_SPORT=y
+CONFIG_BFIN_TIMER_LATENCY=y
+# CONFIG_AD5304 is not set
+# CONFIG_BF5xx_FBDMA is not set
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_DMA=y
+# CONFIG_SERIAL_BFIN_PIO is not set
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_BFIN_UART0_CTSRTS is not set
+# CONFIG_SERIAL_BFIN_UART1 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_BFIN_SPORT is not set
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+
+#
+# CAN, the car bus and industrial fieldbus
+#
+# CONFIG_CAN4LINUX is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_BFIN_WDT is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_GEN_RTC is not set
+CONFIG_BLACKFIN_DPMC=y
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BFIN=y
+# CONFIG_SPI_BITBANG is not set
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_AT25=y
+CONFIG_SPI_SPIDEV=y
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_LM70 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+CONFIG_SOUND=m
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+# CONFIG_SND_SEQUENCER is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+
+#
+# ALSA Blackfin devices
+#
+CONFIG_SND_BLACKFIN_AD1836=m
+CONFIG_SND_BLACKFIN_AD1836_TDM=y
+# CONFIG_SND_BLACKFIN_AD1836_I2S is not set
+CONFIG_SND_BLACKFIN_AD1836_MULSUB=y
+# CONFIG_SND_BLACKFIN_AD1836_5P1 is not set
+CONFIG_SND_BLACKFIN_SPORT=0
+CONFIG_SND_BLACKFIN_SPI_PFBIT=4
+# CONFIG_SND_BFIN_AD73311 is not set
+
+#
+# System on Chip audio support
+#
+# CONFIG_SND_SOC is not set
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
+
+#
+# HID Devices
+#
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+
+#
+# Enable Host or Gadget support to see Inventra options
+#
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_BFIN=y
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# PBX support
+#
+# CONFIG_PBX is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+# CONFIG_EXT2_FS_POSIX_ACL is not set
+# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_YAFFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MMRS is not set
+CONFIG_DEBUG_HUNT_FOR_ZERO=y
+CONFIG_DEBUG_BFIN_HWTRACE_ON=y
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set
+# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set
+CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0
+# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set
+# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set
+# CONFIG_EARLY_PRINTK is not set
+CONFIG_CPLB_INFO=y
+CONFIG_ACCESS_CHECK=y
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+CONFIG_SECURITY=y
+# CONFIG_SECURITY_NETWORK is not set
+CONFIG_SECURITY_CAPABILITIES=y
+
+#
+# Cryptographic options
+#
+# CONFIG_CRYPTO is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_CRC_CCITT=m
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22.6
+# Linux kernel version: 2.6.22.12
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_BLACKFIN=y
CONFIG_ZONE_DMA=y
-CONFIG_BFIN=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_IRQCHIP_DEMUX_GPIO=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=9
#
# Processor and Board Settings
#
+# CONFIG_BF522 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF527 is not set
# CONFIG_BF531 is not set
# CONFIG_BF532 is not set
# CONFIG_BF533 is not set
CONFIG_BF537=y
# CONFIG_BF542 is not set
# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
# CONFIG_BF548 is not set
# CONFIG_BF549 is not set
# CONFIG_BF561 is not set
# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
CONFIG_BF_REV_0_2=y
# CONFIG_BF_REV_0_3 is not set
# CONFIG_BF_REV_0_4 is not set
# CONFIG_BF_REV_NONE is not set
CONFIG_BF53x=y
CONFIG_BFIN_SINGLE_CORE=y
-# CONFIG_BFIN533_EZKIT is not set
-# CONFIG_BFIN533_STAMP is not set
-# CONFIG_BFIN537_STAMP is not set
-# CONFIG_BFIN533_BLUETECHNIX_CM is not set
-# CONFIG_BFIN537_BLUETECHNIX_CM is not set
-# CONFIG_BFIN548_EZKIT is not set
-# CONFIG_BFIN561_BLUETECHNIX_CM is not set
-# CONFIG_BFIN561_EZKIT is not set
-# CONFIG_BFIN561_TEPLA is not set
-CONFIG_PNAV10=y
-# CONFIG_GENERIC_BOARD is not set
CONFIG_MEM_MT48LC32M8A2_75=y
CONFIG_IRQ_PLL_WAKEUP=7
-
-#
-# BF537 Specific Configuration
-#
-
-#
-# Interrupt Priority Assignment
-#
-
-#
-# Priority
-#
-CONFIG_IRQ_DMA_ERROR=7
-CONFIG_IRQ_ERROR=7
CONFIG_IRQ_RTC=8
CONFIG_IRQ_PPI=8
CONFIG_IRQ_SPORT0_RX=9
CONFIG_IRQ_UART0_TX=10
CONFIG_IRQ_UART1_RX=10
CONFIG_IRQ_UART1_TX=10
-CONFIG_IRQ_CAN_RX=11
-CONFIG_IRQ_CAN_TX=11
CONFIG_IRQ_MAC_RX=11
CONFIG_IRQ_MAC_TX=11
CONFIG_IRQ_TMR0=12
CONFIG_IRQ_TMR5=12
CONFIG_IRQ_TMR6=12
CONFIG_IRQ_TMR7=12
-CONFIG_IRQ_PROG_INTA=12
CONFIG_IRQ_PORTG_INTB=12
CONFIG_IRQ_MEM_DMA0=13
CONFIG_IRQ_MEM_DMA1=13
CONFIG_IRQ_WATCH=13
+# CONFIG_BFIN537_STAMP is not set
+# CONFIG_BFIN537_BLUETECHNIX_CM is not set
+CONFIG_PNAV10=y
+# CONFIG_GENERIC_BF537_BOARD is not set
+
+#
+# BF537 Specific Configuration
+#
+
+#
+# Interrupt Priority Assignment
+#
+
+#
+# Priority
+#
+CONFIG_IRQ_DMA_ERROR=7
+CONFIG_IRQ_ERROR=7
+CONFIG_IRQ_CAN_RX=11
+CONFIG_IRQ_CAN_TX=11
+CONFIG_IRQ_PROG_INTA=12
#
# Board customizations
# CONFIG_BFIN_KERNEL_CLOCK is not set
CONFIG_MAX_VCO_HZ=600000000
CONFIG_MIN_VCO_HZ=50000000
-CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MAX_SCLK_HZ=133000000
CONFIG_MIN_SCLK_HZ=27000000
#
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
CONFIG_BFIN_DMA_5XX=y
# CONFIG_DMA_UNCACHED_2M is not set
CONFIG_DMA_UNCACHED_1M=y
#
#
-# EBIU_AMBCTL Global Control
+# EBIU_AMGCTL Global Control
#
CONFIG_C_AMCKEN=y
CONFIG_C_CDPRIO=y
# CONFIG_DM9000 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
+# CONFIG_AX88180 is not set
#
# Wireless LAN
#
# CONFIG_AD9960 is not set
# CONFIG_SPI_ADC_BF533 is not set
-# CONFIG_BFIN_PFLAGS is not set
+# CONFIG_BF5xx_PFLAGS is not set
# CONFIG_BF5xx_PPIFCD is not set
-# CONFIG_BF5xx_TIMERS is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
# CONFIG_BF5xx_PPI is not set
CONFIG_BFIN_SPORT=y
# CONFIG_BFIN_TIMER_LATENCY is not set
CONFIG_LQ035_SLAVE_ADDR=0x58
CONFIG_FB_BFIN_LANDSCAPE=y
# CONFIG_FB_BFIN_BGR is not set
+# CONFIG_FB_BFIN_T350MCQB is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_LOGO is not set
#
# CONFIG_SND_SOC is not set
-#
-# SoC Audio for the ADI Blackfin
-#
-# CONFIG_SND_BF5XX_HAVE_COLD_RESET is not set
-
#
# Open Sound System
#
return dma_ch[channel].regs->curr_desc_ptr;
}
+EXPORT_SYMBOL(get_dma_curr_desc_ptr);
unsigned long get_dma_curr_addr(unsigned int channel)
{
/* platform dependent support */
EXPORT_SYMBOL(__ioremap);
-EXPORT_SYMBOL(strcmp);
-EXPORT_SYMBOL(strncmp);
-EXPORT_SYMBOL(dump_thread);
EXPORT_SYMBOL(ip_fast_csum);
EXPORT_SYMBOL(__down_interruptible);
EXPORT_SYMBOL(is_in_rom);
+EXPORT_SYMBOL(bfin_return_from_exception);
/* Networking helper routines. */
EXPORT_SYMBOL(csum_partial_copy);
* their interface isn't gonna change any time soon now, so
* it's OK to leave it out of version control.
*/
-EXPORT_SYMBOL(strcpy);
EXPORT_SYMBOL(memcpy);
EXPORT_SYMBOL(memset);
EXPORT_SYMBOL(memcmp);
EXPORT_SYMBOL(memmove);
EXPORT_SYMBOL(memchr);
-EXPORT_SYMBOL(get_wchan);
/*
* libgcc functions - functions that are used internally by the
EXPORT_SYMBOL(insw);
EXPORT_SYMBOL(outsl);
EXPORT_SYMBOL(insl);
+EXPORT_SYMBOL(insl_16);
EXPORT_SYMBOL(irq_flags);
EXPORT_SYMBOL(iounmap);
EXPORT_SYMBOL(blackfin_dcache_invalidate_range);
#include <asm/cplb.h>
#include <asm/cplbinit.h>
-u_long icplb_table[MAX_CPLBS+1];
-u_long dcplb_table[MAX_CPLBS+1];
+u_long icplb_table[MAX_CPLBS + 1];
+u_long dcplb_table[MAX_CPLBS + 1];
#ifdef CONFIG_CPLB_SWITCH_TAB_L1
-u_long ipdt_table[MAX_SWITCH_I_CPLBS+1]__attribute__((l1_data));
-u_long dpdt_table[MAX_SWITCH_D_CPLBS+1]__attribute__((l1_data));
-
-#ifdef CONFIG_CPLB_INFO
-u_long ipdt_swapcount_table[MAX_SWITCH_I_CPLBS]__attribute__((l1_data));
-u_long dpdt_swapcount_table[MAX_SWITCH_D_CPLBS]__attribute__((l1_data));
-#endif /* CONFIG_CPLB_INFO */
-
+# define PDT_ATTR __attribute__((l1_data))
#else
+# define PDT_ATTR
+#endif
-u_long ipdt_table[MAX_SWITCH_I_CPLBS+1];
-u_long dpdt_table[MAX_SWITCH_D_CPLBS+1];
+u_long ipdt_table[MAX_SWITCH_I_CPLBS + 1] PDT_ATTR;
+u_long dpdt_table[MAX_SWITCH_D_CPLBS + 1] PDT_ATTR;
#ifdef CONFIG_CPLB_INFO
-u_long ipdt_swapcount_table[MAX_SWITCH_I_CPLBS];
-u_long dpdt_swapcount_table[MAX_SWITCH_D_CPLBS];
-#endif /* CONFIG_CPLB_INFO */
-
-#endif /*CONFIG_CPLB_SWITCH_TAB_L1*/
+u_long ipdt_swapcount_table[MAX_SWITCH_I_CPLBS] PDT_ATTR;
+u_long dpdt_swapcount_table[MAX_SWITCH_D_CPLBS] PDT_ATTR;
+#endif
struct s_cplb {
struct cplb_tab init_i;
#else
.valid = 0,
#endif
- .name = "ZERO Pointer Saveguard",
+ .name = "Zero Pointer Guard Page",
},
{
.start = L1_CODE_START,
.end = 0, /* dynamic */
.psize = 0,
.attr = INITIAL_T | SWITCH_T | I_CPLB | D_CPLB,
- .i_conf = SDRAM_IGENERIC,
- .d_conf = SDRAM_DGENERIC,
+ .i_conf = SDRAM_IGENERIC,
+ .d_conf = SDRAM_DGENERIC,
.valid = 1,
- .name = "SDRAM Kernel",
+ .name = "Kernel Memory",
},
{
.start = 0, /* dynamic */
.end = 0, /* dynamic */
.psize = 0,
.attr = INITIAL_T | SWITCH_T | D_CPLB,
- .i_conf = SDRAM_IGENERIC,
- .d_conf = SDRAM_DNON_CHBL,
+ .i_conf = SDRAM_IGENERIC,
+ .d_conf = SDRAM_DNON_CHBL,
.valid = 1,
- .name = "SDRAM RAM MTD",
+ .name = "uClinux MTD Memory",
},
{
.start = 0, /* dynamic */
.attr = INITIAL_T | SWITCH_T | D_CPLB,
.d_conf = SDRAM_DNON_CHBL,
.valid = 1,
- .name = "SDRAM Uncached DMA ZONE",
+ .name = "Uncached DMA Zone",
},
{
.start = 0, /* dynamic */
.i_conf = 0, /* dynamic */
.d_conf = 0, /* dynamic */
.valid = 1,
- .name = "SDRAM Reserved Memory",
+ .name = "Reserved Memory",
},
{
.start = ASYNC_BANK0_BASE,
.attr = SWITCH_T | D_CPLB,
.d_conf = SDRAM_EBIU,
.valid = 1,
- .name = "ASYNC Memory",
+ .name = "Asynchronous Memory Banks",
},
{
-#if defined(CONFIG_BF561)
- .start = L2_SRAM,
- .end = L2_SRAM_END,
+#ifdef L2_START
+ .start = L2_START,
+ .end = L2_START + L2_LENGTH,
.psize = SIZE_1M,
- .attr = SWITCH_T | D_CPLB,
+ .attr = SWITCH_T | I_CPLB | D_CPLB,
.i_conf = L2_MEMORY,
.d_conf = L2_MEMORY,
.valid = 1,
.valid = 0,
#endif
.name = "L2 Memory",
- }
+ },
+ {
+ .start = BOOT_ROM_START,
+ .end = BOOT_ROM_START + BOOT_ROM_LENGTH,
+ .psize = SIZE_1M,
+ .attr = SWITCH_T | I_CPLB | D_CPLB,
+ .i_conf = SDRAM_IGENERIC,
+ .d_conf = SDRAM_DGENERIC,
+ .valid = 1,
+ .name = "On-Chip BootROM",
+ },
};
static u16 __init lock_kernel_check(u32 start, u32 end)
{
- if ((start <= (u32) _stext && end >= (u32) _end)
- || (start >= (u32) _stext && end <= (u32) _end))
+ if ((end <= (u32) _end && end >= (u32)_stext) ||
+ (start <= (u32) _end && start >= (u32)_stext))
return IN_KERNEL;
return 0;
}
else
cplb_data[RES_MEM].i_conf = SDRAM_INON_CHBL;
- for (i = ZERO_P; i <= L2_MEM; i++) {
+ for (i = ZERO_P; i < ARRAY_SIZE(cplb_data); ++i) {
if (!cplb_data[i].valid)
continue;
if (likely(early_console == NULL))
setup_early_printk(DEFAULT_EARLY_PORT);
- dump_bfin_regs(fp, retaddr);
+ dump_bfin_mem((void *)fp->retx);
+ show_regs(fp);
dump_bfin_trace_buffer();
panic("Died early");
}
}
-void show_regs(struct pt_regs *regs)
-{
- printk(KERN_NOTICE "\n");
- printk(KERN_NOTICE
- "PC: %08lu Status: %04lu SysStatus: %04lu RETS: %08lu\n",
- regs->pc, regs->astat, regs->seqstat, regs->rets);
- printk(KERN_NOTICE
- "A0.x: %08lx A0.w: %08lx A1.x: %08lx A1.w: %08lx\n",
- regs->a0x, regs->a0w, regs->a1x, regs->a1w);
- printk(KERN_NOTICE "P0: %08lx P1: %08lx P2: %08lx P3: %08lx\n",
- regs->p0, regs->p1, regs->p2, regs->p3);
- printk(KERN_NOTICE "P4: %08lx P5: %08lx\n", regs->p4, regs->p5);
- printk(KERN_NOTICE "R0: %08lx R1: %08lx R2: %08lx R3: %08lx\n",
- regs->r0, regs->r1, regs->r2, regs->r3);
- printk(KERN_NOTICE "R4: %08lx R5: %08lx R6: %08lx R7: %08lx\n",
- regs->r4, regs->r5, regs->r6, regs->r7);
-
- if (!regs->ipend)
- printk(KERN_NOTICE "USP: %08lx\n", rdusp());
-}
-
/* Fill in the fpu structure for a core dump. */
int dump_fpu(struct pt_regs *regs, elf_fpregset_t * fpregs)
return 0;
}
-/*
- * fill in the user structure for a core dump..
- */
-void dump_thread(struct pt_regs *regs, struct user *dump)
-{
- dump->magic = CMAGIC;
- dump->start_code = 0;
- dump->start_stack = rdusp() & ~(PAGE_SIZE - 1);
- dump->u_tsize = ((unsigned long)current->mm->end_code) >> PAGE_SHIFT;
- dump->u_dsize = ((unsigned long)(current->mm->brk +
- (PAGE_SIZE - 1))) >> PAGE_SHIFT;
- dump->u_dsize -= dump->u_tsize;
- dump->u_ssize = 0;
-
- if (dump->start_stack < TASK_SIZE)
- dump->u_ssize =
- ((unsigned long)(TASK_SIZE -
- dump->start_stack)) >> PAGE_SHIFT;
-
- dump->u_ar0 = (struct user_regs_struct *)((int)&dump->regs - (int)dump);
-
- dump->regs.r0 = regs->r0;
- dump->regs.r1 = regs->r1;
- dump->regs.r2 = regs->r2;
- dump->regs.r3 = regs->r3;
- dump->regs.r4 = regs->r4;
- dump->regs.r5 = regs->r5;
- dump->regs.r6 = regs->r6;
- dump->regs.r7 = regs->r7;
- dump->regs.p0 = regs->p0;
- dump->regs.p1 = regs->p1;
- dump->regs.p2 = regs->p2;
- dump->regs.p3 = regs->p3;
- dump->regs.p4 = regs->p4;
- dump->regs.p5 = regs->p5;
- dump->regs.orig_p0 = regs->orig_p0;
- dump->regs.a0w = regs->a0w;
- dump->regs.a1w = regs->a1w;
- dump->regs.a0x = regs->a0x;
- dump->regs.a1x = regs->a1x;
- dump->regs.rets = regs->rets;
- dump->regs.astat = regs->astat;
- dump->regs.pc = regs->pc;
-}
-
/*
* sys_execve() executes a new program.
*/
#include <asm/cacheflush.h>
#include <asm/blackfin.h>
#include <asm/cplbinit.h>
+#include <asm/div64.h>
#include <asm/fixed_code.h>
#include <asm/early_printk.h>
unsigned long sclk_to_usecs(unsigned long sclk)
{
- return (USEC_PER_SEC * (u64)sclk) / get_sclk();
+ u64 tmp = USEC_PER_SEC * (u64)sclk;
+ do_div(tmp, get_sclk());
+ return tmp;
}
EXPORT_SYMBOL(sclk_to_usecs);
unsigned long usecs_to_sclk(unsigned long usecs)
{
- return (get_sclk() * (u64)usecs) / USEC_PER_SEC;
+ u64 tmp = get_sclk() * (u64)usecs;
+ do_div(tmp, USEC_PER_SEC);
+ return tmp;
}
EXPORT_SYMBOL(usecs_to_sclk);
}
/* we were unable to find this address anywhere */
- sprintf(buf, "[<0x%p>]", (void *)address);
+ sprintf(buf, "<0x%p> /* unknown address */", (void *)address);
done:
write_unlock_irqrestore(&tasklist_lock, flags);
console_verbose();
oops_in_progress = 1;
printk(KERN_EMERG "\n" KERN_EMERG "Double Fault\n");
- dump_bfin_regs(fp, (void *)fp->retx);
+ dump_bfin_process(fp);
+ dump_bfin_mem((void *)fp->retx);
+ show_regs(fp);
panic("Double Fault - unrecoverable event\n");
}
case VEC_EXCPT03:
info.si_code = SEGV_STACKFLOW;
sig = SIGSEGV;
- printk(KERN_NOTICE EXC_0x03);
+ printk(KERN_NOTICE EXC_0x03(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x04 - User Defined, Caught by default */
case VEC_OVFLOW:
info.si_code = TRAP_TRACEFLOW;
sig = SIGTRAP;
- printk(KERN_NOTICE EXC_0x11);
+ printk(KERN_NOTICE EXC_0x11(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x12 - Reserved, Caught by default */
case VEC_UNDEF_I:
info.si_code = ILL_ILLOPC;
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x21);
+ printk(KERN_NOTICE EXC_0x21(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x22 - Illegal Instruction Combination, handled here */
case VEC_ILGAL_I:
info.si_code = ILL_ILLPARAOP;
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x22);
+ printk(KERN_NOTICE EXC_0x22(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
- /* 0x23 - Data CPLB Protection Violation,
- normal case is handled in _cplb_hdr */
+ /* 0x23 - Data CPLB protection violation, handled here */
case VEC_CPLB_VL:
info.si_code = ILL_CPLB_VI;
- sig = SIGILL;
- printk(KERN_NOTICE EXC_0x23);
+ sig = SIGBUS;
+ printk(KERN_NOTICE EXC_0x23(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x24 - Data access misaligned, handled here */
case VEC_MISALI_D:
info.si_code = BUS_ADRALN;
sig = SIGBUS;
- printk(KERN_NOTICE EXC_0x24);
+ printk(KERN_NOTICE EXC_0x24(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x25 - Unrecoverable Event, handled here */
case VEC_UNCOV:
info.si_code = ILL_ILLEXCPT;
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x25);
+ printk(KERN_NOTICE EXC_0x25(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x26 - Data CPLB Miss, normal case is handled in _cplb_hdr,
case VEC_CPLB_M:
info.si_code = BUS_ADRALN;
sig = SIGBUS;
- printk(KERN_NOTICE EXC_0x26);
+ printk(KERN_NOTICE EXC_0x26(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x27 - Data CPLB Multiple Hits - Linux Trap Zero, handled here */
printk(KERN_NOTICE "NULL pointer access (probably)\n");
#else
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x27);
+ printk(KERN_NOTICE EXC_0x27(KERN_NOTICE));
#endif
CHK_DEBUGGER_TRAP();
break;
case VEC_WATCH:
info.si_code = TRAP_WATCHPT;
sig = SIGTRAP;
- pr_debug(EXC_0x28);
+ pr_debug(EXC_0x28(KERN_DEBUG));
CHK_DEBUGGER_TRAP_MAYBE();
/* Check if this is a watchpoint in kernel space */
if (fp->ipend & 0xffc0)
case VEC_MISALI_I:
info.si_code = BUS_ADRALN;
sig = SIGBUS;
- printk(KERN_NOTICE EXC_0x2A);
+ printk(KERN_NOTICE EXC_0x2A(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
- /* 0x2B - Instruction CPLB protection Violation,
- handled in _cplb_hdr */
+ /* 0x2B - Instruction CPLB protection violation, handled here */
case VEC_CPLB_I_VL:
info.si_code = ILL_CPLB_VI;
- sig = SIGILL;
- printk(KERN_NOTICE EXC_0x2B);
+ sig = SIGBUS;
+ printk(KERN_NOTICE EXC_0x2B(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x2C - Instruction CPLB miss, handled in _cplb_hdr */
case VEC_CPLB_I_M:
info.si_code = ILL_CPLB_MISS;
sig = SIGBUS;
- printk(KERN_NOTICE EXC_0x2C);
+ printk(KERN_NOTICE EXC_0x2C(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x2D - Instruction CPLB Multiple Hits, handled here */
printk(KERN_NOTICE "Jump to address 0 - 0x0fff\n");
#else
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x2D);
+ printk(KERN_NOTICE EXC_0x2D(KERN_NOTICE));
#endif
CHK_DEBUGGER_TRAP();
break;
case VEC_ILL_RES:
info.si_code = ILL_PRVOPC;
sig = SIGILL;
- printk(KERN_NOTICE EXC_0x2E);
+ printk(KERN_NOTICE EXC_0x2E(KERN_NOTICE));
CHK_DEBUGGER_TRAP();
break;
/* 0x2F - Reserved, Caught by default */
if (sig != SIGTRAP) {
unsigned long stack;
- dump_bfin_regs(fp, (void *)fp->retx);
+ dump_bfin_process(fp);
+ dump_bfin_mem((void *)fp->retx);
+ show_regs(fp);
/* Print out the trace buffer if it makes sense */
#ifndef CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE
show_stack(current, &stack);
if (oops_in_progress) {
#ifndef CONFIG_ACCESS_CHECK
- printk(KERN_EMERG "Hey - dork - please turn on "
- "CONFIG_ACCESS_CHECK\n");
+ printk(KERN_EMERG "Please turn on "
+ "CONFIG_ACCESS_CHECK\n");
#endif
panic("Kernel exception");
}
-
- /* Ensure that bad return addresses don't end up in an infinite
- * loop, due to speculative loads/reads
- */
- fp->pc = SAFE_USER_INSTRUCTION;
}
+
info.si_signo = sig;
info.si_errno = 0;
info.si_addr = (void *)fp->pc;
force_sig_info(sig, &info, current);
+ /* Ensure that bad return addresses don't end up in an infinite
+ * loop, due to speculative loads/reads. This needs to be done after
+ * the signal has been sent.
+ */
+ if (trapnr == VEC_CPLB_I_M && sig != SIGTRAP)
+ fp->pc = SAFE_USER_INSTRUCTION;
+
trace_buffer_restore(j);
return;
}
show_stack(current, &stack);
trace_buffer_restore(tflags);
}
-
EXPORT_SYMBOL(dump_stack);
-void dump_bfin_regs(struct pt_regs *fp, void *retaddr)
+void dump_bfin_process(struct pt_regs *fp)
{
- char buf [150];
+ /* We should be able to look at fp->ipend, but we don't push it on the
+ * stack all the time, so do this until we fix that */
+ unsigned int context = bfin_read_IPEND();
+
+ if (oops_in_progress)
+ printk(KERN_EMERG "Kernel OOPS in progress\n");
+
+ if (context & 0x0020)
+ printk(KERN_NOTICE "Deferred excecption or HW Error context\n");
+ else if (context & 0x3FC0)
+ printk(KERN_NOTICE "Interrupt context\n");
+ else if (context & 0x4000)
+ printk(KERN_NOTICE "Deferred Interrupt context\n");
+ else if (context & 0x8000)
+ printk(KERN_NOTICE "Kernel process context\n");
+
+ if (current->pid && current->mm) {
+ printk(KERN_NOTICE "CURRENT PROCESS:\n");
+ printk(KERN_NOTICE "COMM=%s PID=%d\n",
+ current->comm, current->pid);
+
+ printk(KERN_NOTICE "TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
+ KERN_NOTICE "BSS = 0x%p-0x%p USER-STACK = 0x%p\n"
+ KERN_NOTICE "\n",
+ (void *)current->mm->start_code,
+ (void *)current->mm->end_code,
+ (void *)current->mm->start_data,
+ (void *)current->mm->end_data,
+ (void *)current->mm->end_data,
+ (void *)current->mm->brk,
+ (void *)current->mm->start_stack);
+ } else
+ printk(KERN_NOTICE "\n" KERN_NOTICE
+ "No Valid process in current context\n");
+}
- if (!oops_in_progress) {
- if (current->pid && current->mm) {
- printk(KERN_NOTICE "\n" KERN_NOTICE "CURRENT PROCESS:\n");
- printk(KERN_NOTICE "COMM=%s PID=%d\n",
- current->comm, current->pid);
-
- printk(KERN_NOTICE "TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
- KERN_NOTICE "BSS = 0x%p-0x%p USER-STACK = 0x%p\n"
- KERN_NOTICE "\n",
- (void *)current->mm->start_code,
- (void *)current->mm->end_code,
- (void *)current->mm->start_data,
- (void *)current->mm->end_data,
- (void *)current->mm->end_data,
- (void *)current->mm->brk,
- (void *)current->mm->start_stack);
- } else {
- printk (KERN_NOTICE "\n" KERN_NOTICE
- "No Valid pid - Either things are really messed up,"
- " or you are in the kernel\n");
- }
- } else {
- printk(KERN_NOTICE "Kernel or interrupt exception\n");
- }
+void dump_bfin_mem(void *retaddr)
+{
if (retaddr >= (void *)FIXED_CODE_START && retaddr < (void *)physical_mem_end
#if L1_CODE_LENGTH != 0
printk("\n");
} else
printk("\n" KERN_NOTICE
- "Cannot look at the [PC] for it is"
- " in unreadable memory - sorry\n");
+ "Cannot look at the [PC] <%p> for it is"
+ " in unreadable memory - sorry\n", retaddr);
+}
+
+void show_regs(struct pt_regs *fp)
+{
+ char buf [150];
printk(KERN_NOTICE "\n" KERN_NOTICE "SEQUENCER STATUS:\n");
printk(KERN_NOTICE " SEQSTAT: %08lx IPEND: %04lx SYSCFG: %04lx\n",
printk(KERN_NOTICE " RETX: %s\n", buf);
decode_address(buf, fp->rets);
printk(KERN_NOTICE " RETS: %s\n", buf);
+ decode_address(buf, fp->pc);
+ printk(KERN_NOTICE " PC: %s\n", buf);
if ((long)fp->seqstat & SEQSTAT_EXCAUSE) {
decode_address(buf, bfin_read_DCPLB_FAULT_ADDR());
printk(KERN_EMERG "DCPLB_FAULT_ADDR=%p\n", (void *)bfin_read_DCPLB_FAULT_ADDR());
printk(KERN_EMERG "ICPLB_FAULT_ADDR=%p\n", (void *)bfin_read_ICPLB_FAULT_ADDR());
- dump_bfin_regs(fp, (void *)fp->retx);
+ dump_bfin_process(fp);
+ dump_bfin_mem((void *)fp->retx);
+ show_regs(fp);
dump_stack();
panic("Unrecoverable event\n");
}
lib-y := \
ashldi3.o ashrdi3.o lshrdi3.o \
- muldi3.o divsi3.o udivsi3.o udivdi3.o modsi3.o umodsi3.o \
+ muldi3.o divsi3.o udivsi3.o modsi3.o umodsi3.o \
checksum.o memcpy.o memset.o memcmp.o memchr.o memmove.o \
strcmp.o strcpy.o strncmp.o strncpy.o \
umulsi3_highpart.o smulsi3_highpart.o \
sti R3;
RTS;
ENDPROC(_insb)
+
+
+
+ENTRY(_insl_16)
+ P0 = R0; /* P0 = port */
+ cli R3;
+ P1 = R1; /* P1 = address */
+ P2 = R2; /* P2 = count */
+ SSYNC;
+ LSETUP( .Llong16_loop_s, .Llong16_loop_e) LC0 = P2;
+.Llong16_loop_s: R0 = [P0];
+ W[P1++] = R0;
+ R0 = R0 >> 16;
+ W[P1++] = R0;
+ NOP;
+.Llong16_loop_e: NOP;
+ sti R3;
+ RTS;
+ENDPROC(_insl_16)
-#include <linux/types.h>
+/*
+ * Provide symbol in case str func is not inlined.
+ *
+ * Copyright (c) 2006-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
#define strcmp __inline_strcmp
#include <asm/string.h>
#undef strcmp
+#include <linux/module.h>
+
int strcmp(const char *dest, const char *src)
{
return __inline_strcmp(dest, src);
}
+EXPORT_SYMBOL(strcmp);
-#include <linux/types.h>
+/*
+ * Provide symbol in case str func is not inlined.
+ *
+ * Copyright (c) 2006-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
#define strcpy __inline_strcpy
#include <asm/string.h>
#undef strcpy
+#include <linux/module.h>
+
char *strcpy(char *dest, const char *src)
{
return __inline_strcpy(dest, src);
}
+EXPORT_SYMBOL(strcpy);
-#include <linux/types.h>
+/*
+ * Provide symbol in case str func is not inlined.
+ *
+ * Copyright (c) 2006-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
#define strncmp __inline_strncmp
#include <asm/string.h>
#undef strncmp
+#include <linux/module.h>
+
int strncmp(const char *cs, const char *ct, size_t count)
{
return __inline_strncmp(cs, ct, count);
}
+EXPORT_SYMBOL(strncmp);
-#include <linux/types.h>
+/*
+ * Provide symbol in case str func is not inlined.
+ *
+ * Copyright (c) 2006-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
#define strncpy __inline_strncpy
#include <asm/string.h>
#undef strncpy
+#include <linux/module.h>
+
char *strncpy(char *dest, const char *src, size_t n)
{
return __inline_strncpy(dest, src, n);
}
+EXPORT_SYMBOL(strncpy);
+++ /dev/null
-/*
- * udivdi3.S - unsigned long long division
- *
- * Copyright 2003-2007 Analog Devices Inc.
- * Enter bugs at http://blackfin.uclinux.org/
- *
- * Licensed under the GPLv2 or later.
- */
-
-#include <linux/linkage.h>
-
-#define CARRY AC0
-
-#ifdef CONFIG_ARITHMETIC_OPS_L1
-.section .l1.text
-#else
-.text
-#endif
-
-
-ENTRY(___udivdi3)
- R3 = [SP + 12];
- [--SP] = (R7:4, P5:3);
-
- /* Attempt to use divide primitive first; these will handle
- ** most cases, and they're quick - avoids stalls incurred by
- ** testing for identities.
- */
-
- R4 = R2 | R3;
- CC = R4 == 0;
- IF CC JUMP .LDIV_BY_ZERO;
-
- R4.H = 0x8000;
- R4 >>>= 16; // R4 now 0xFFFF8000
- R5 = R0 | R2; // If either dividend or
- R4 = R5 & R4; // divisor have bits in
- CC = R4; // top half or low half's sign
- IF CC JUMP .LIDENTS; // bit, skip builtins.
- R4 = R1 | R3; // Also check top halves
- CC = R4;
- IF CC JUMP .LIDENTS;
-
- /* Can use the builtins. */
-
- AQ = CC; // Clear AQ (CC==0)
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- DIVQ(R0, R2);
- R0 = R0.L (Z);
- R1 = 0;
- (R7:4, P5:3) = [SP++];
- RTS;
-
-.LIDENTS:
- /* Test for common identities. Value to be returned is
- ** placed in R6,R7.
- */
- // Check for 0/y, return 0
- R4 = R0 | R1;
- CC = R4 == 0;
- IF CC JUMP .LRETURN_R0;
-
- // Check for x/x, return 1
- R6 = R0 - R2; // If x == y, then both R6 and R7 will be zero
- R7 = R1 - R3;
- R4 = R6 | R7; // making R4 zero.
- R6 += 1; // which would now make R6:R7==1.
- CC = R4 == 0;
- IF CC JUMP .LRETURN_IDENT;
-
- // Check for x/1, return x
- R6 = R0;
- R7 = R1;
- CC = R3 == 0;
- IF !CC JUMP .Lnexttest;
- CC = R2 == 1;
- IF CC JUMP .LRETURN_IDENT;
-
-.Lnexttest:
- R4.L = ONES R2; // check for div by power of two which
- R5.L = ONES R3; // can be done using a shift
- R6 = PACK (R5.L, R4.L);
- CC = R6 == 1;
- IF CC JUMP .Lpower_of_two_upper_zero;
- R6 = PACK (R4.L, R5.L);
- CC = R6 == 1;
- IF CC JUMP .Lpower_of_two_lower_zero;
-
- // Check for x < y, return 0
- R6 = 0;
- R7 = R6;
- CC = R1 < R3 (IU);
- IF CC JUMP .LRETURN_IDENT;
- CC = R1 == R3;
- IF !CC JUMP .Lno_idents;
- CC = R0 < R2 (IU);
- IF CC JUMP .LRETURN_IDENT;
-
-.Lno_idents: // Idents don't match. Go for the full operation
-
-
- // If X, or X and Y have high bit set, it'll affect the
- // results, so shift right one to stop this. Note: we've already
- // checked that X >= Y, so Y's msb won't be set unless X's
- // is.
-
- R4 = 0;
- CC = R1 < 0;
- IF !CC JUMP .Lx_msb_clear;
- CC = !CC; // 1 -> 0;
- R1 = ROT R1 BY -1; // Shift X >> 1
- R0 = ROT R0 BY -1; // lsb -> CC
- BITSET(R4,31); // to record only x msb was set
- CC = R3 < 0;
- IF !CC JUMP .Ly_msb_clear;
- CC = !CC;
- R3 = ROT R3 BY -1; // Shift Y >> 1
- R2 = ROT R2 BY -1;
- BITCLR(R4,31); // clear bit to record only x msb was set
-
-.Ly_msb_clear:
-.Lx_msb_clear:
- // Bit 31 in R4 indicates X msb set, but Y msb wasn't, and no bits
- // were lost, so we should shift result left by one.
-
- [--SP] = R4; // save for later
-
- // In the loop that follows, each iteration we add
- // either Y' or -Y' to the Remainder. We compute the
- // negated Y', and store, for convenience. Y' goes
- // into P0:P1, while -Y' goes into P2:P3.
-
- P0 = R2;
- P1 = R3;
- R2 = -R2;
- CC = CARRY;
- CC = !CC;
- R4 = CC;
- R3 = -R3;
- R3 = R3 - R4;
-
- R6 = 0; // remainder = 0
- R7 = R6;
-
- [--SP] = R2; P2 = SP;
- [--SP] = R3; P3 = SP;
- [--SP] = R6; P5 = SP; // AQ = 0
- [--SP] = P1;
-
- /* In the loop that follows, we use the following
- ** register assignments:
- ** R0,R1 X, workspace
- ** R2,R3 Y, workspace
- ** R4,R5 partial Div
- ** R6,R7 partial remainder
- ** P5 AQ
- ** The remainder and div form a 128-bit number, with
- ** the remainder in the high 64-bits.
- */
- R4 = R0; // Div = X'
- R5 = R1;
- R3 = 0;
-
- P4 = 64; // Iterate once per bit
- LSETUP(.LULST,.LULEND) LC0 = P4;
-.LULST:
- /* Shift Div and remainder up by one. The bit shifted
- ** out of the top of the quotient is shifted into the bottom
- ** of the remainder.
- */
- CC = R3;
- R4 = ROT R4 BY 1;
- R5 = ROT R5 BY 1 || // low q to high q
- R2 = [P5]; // load saved AQ
- R6 = ROT R6 BY 1 || // high q to low r
- R0 = [P2]; // load -Y'
- R7 = ROT R7 BY 1 || // low r to high r
- R1 = [P3];
-
- // Assume add -Y'
- CC = R2 < 0; // But if AQ is set...
- IF CC R0 = P0; // then add Y' instead
- IF CC R1 = P1;
-
- R6 = R6 + R0; // Rem += (Y' or -Y')
- CC = CARRY;
- R0 = CC;
- R7 = R7 + R1;
- R7 = R7 + R0 (NS) ||
- R1 = [SP];
- // Set the next AQ bit
- R1 = R7 ^ R1; // from Remainder and Y'
- R1 = R1 >> 31 || // Negate AQ's value, and
- [P5] = R1; // save next AQ
- BITTGL(R1, 0); // add neg AQ to the Div
-.LULEND: R4 = R4 + R1;
-
- R6 = [SP + 16];
-
- R0 = R4;
- R1 = R5;
- CC = BITTST(R6,30); // Just set CC=0
- R4 = ROT R0 BY 1; // but if we had to shift X,
- R5 = ROT R1 BY 1; // and didn't shift any bits out,
- CC = BITTST(R6,31); // then the result will be half as
- IF CC R0 = R4; // much as required, so shift left
- IF CC R1 = R5; // one space.
-
- SP += 20;
- (R7:4, P5:3) = [SP++];
- RTS;
-
-.Lpower_of_two:
- /* Y has a single bit set, which means it's a power of two.
- ** That means we can perform the division just by shifting
- ** X to the right the appropriate number of bits
- */
-
- /* signbits returns the number of sign bits, minus one.
- ** 1=>30, 2=>29, ..., 0x40000000=>0. Which means we need
- ** to shift right n-signbits spaces. It also means 0x80000000
- ** is a special case, because that *also* gives a signbits of 0
- */
-.Lpower_of_two_lower_zero:
- R7 = 0;
- R6 = R1 >> 31;
- CC = R3 < 0;
- IF CC JUMP .LRETURN_IDENT;
-
- R2.L = SIGNBITS R3;
- R2 = R2.L (Z);
- R2 += -62;
- (R7:4, P5:3) = [SP++];
- JUMP ___lshftli;
-
-.Lpower_of_two_upper_zero:
- CC = R2 < 0;
- IF CC JUMP .Lmaxint_shift;
-
- R2.L = SIGNBITS R2;
- R2 = R2.L (Z);
- R2 += -30;
- (R7:4, P5:3) = [SP++];
- JUMP ___lshftli;
-
-.Lmaxint_shift:
- R2 = -31;
- (R7:4, P5:3) = [SP++];
- JUMP ___lshftli;
-
-.LRETURN_IDENT:
- R0 = R6;
- R1 = R7;
-.LRETURN_R0:
- (R7:4, P5:3) = [SP++];
- RTS;
-.LDIV_BY_ZERO:
- R0 = ~R2;
- R1 = R0;
- (R7:4, P5:3) = [SP++];
- RTS;
-
-ENDPROC(___udivdi3)
-
-
-ENTRY(___lshftli)
- CC = R2 == 0;
- IF CC JUMP .Lfinished; // nothing to do
- CC = R2 < 0;
- IF CC JUMP .Lrshift;
- R3 = 64;
- CC = R2 < R3;
- IF !CC JUMP .Lretzero;
-
- // We're shifting left, and it's less than 64 bits, so
- // a valid result will be returned.
-
- R3 >>= 1; // R3 now 32
- CC = R2 < R3;
-
- IF !CC JUMP .Lzerohalf;
-
- // We're shifting left, between 1 and 31 bits, which means
- // some of the low half will be shifted into the high half.
- // Work out how much.
-
- R3 = R3 - R2;
-
- // Save that much data from the bottom half.
-
- P1 = R7;
- R7 = R0;
- R7 >>= R3;
-
- // Adjust both parts of the parameter.
-
- R0 <<= R2;
- R1 <<= R2;
-
- // And include the bits moved across.
-
- R1 = R1 | R7;
- R7 = P1;
- RTS;
-
-.Lzerohalf:
- // We're shifting left, between 32 and 63 bits, so the
- // bottom half will become zero, and the top half will
- // lose some bits. How many?
-
- R2 = R2 - R3; // N - 32
- R1 = LSHIFT R0 BY R2.L;
- R0 = R0 - R0;
- RTS;
-
-.Lretzero:
- R0 = R0 - R0;
- R1 = R0;
-.Lfinished:
- RTS;
-
-.Lrshift:
- // We're shifting right, but by how much?
- R2 = -R2;
- R3 = 64;
- CC = R2 < R3;
- IF !CC JUMP .Lretzero;
-
- // Shifting right less than 64 bits, so some result bits will
- // be retained.
-
- R3 >>= 1; // R3 now 32
- CC = R2 < R3;
- IF !CC JUMP .Lsignhalf;
-
- // Shifting right between 1 and 31 bits, so need to copy
- // data across words.
-
- P1 = R7;
- R3 = R3 - R2;
- R7 = R1;
- R7 <<= R3;
- R1 >>= R2;
- R0 >>= R2;
- R0 = R7 | R0;
- R7 = P1;
- RTS;
-
-.Lsignhalf:
- // Shifting right between 32 and 63 bits, so the top half
- // will become all zero-bits, and the bottom half is some
- // of the top half. But how much?
-
- R2 = R2 - R3;
- R0 = R1;
- R0 >>= R2;
- R1 = 0;
- RTS;
-
-ENDPROC(___lshftli)
if (BF52x)
+source "arch/blackfin/mach-bf527/boards/Kconfig"
+
menu "BF527 Specific Configuration"
comment "Alternative Multiplexing Scheme"
--- /dev/null
+choice
+ prompt "System type"
+ default BFIN527_EZKIT
+ help
+ Select your board!
+
+config BFIN527_EZKIT
+ bool "BF527-EZKIT"
+ help
+ BF527-EZKIT-LITE board support.
+
+endchoice
#
-# arch/blackfin/mach-bf532/boards/Makefile
+# arch/blackfin/mach-bf527/boards/Makefile
#
-obj-y += eth_mac.o
-obj-$(CONFIG_BFIN527_EZKIT) += ezkit.o
-
+obj-$(CONFIG_BFIN527_EZKIT) += ezkit.o
+++ /dev/null
-/*
- * arch/blackfin/mach-bf537/board/eth_mac.c
- *
- * Copyright (C) 2007 Analog Devices, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#include <linux/module.h>
-#include <asm/blackfin.h>
-
-#if defined(CONFIG_GENERIC_BOARD) || defined(CONFIG_BFIN537_STAMP)
-
-/*
- * Currently the MAC address is saved in Flash by U-Boot
- */
-#define FLASH_MAC 0x203f0000
-
-void get_bf537_ether_addr(char *addr)
-{
- unsigned int flash_mac = (unsigned int) FLASH_MAC;
- *(u32 *)(&(addr[0])) = bfin_read32(flash_mac);
- flash_mac += 4;
- *(u16 *)(&(addr[4])) = bfin_read16(flash_mac);
-}
-
-#else
-
-/*
- * Provide MAC address function for other specific board setting
- */
-void get_bf537_ether_addr(char *addr)
-{
- printk(KERN_WARNING "%s: No valid Ethernet MAC address found\n", __FILE__);
-}
-
-#endif
-
-EXPORT_SYMBOL(get_bf537_ether_addr);
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <linux/usb_sl811.h>
+#include <linux/usb/sl811.h>
#include <asm/cplb.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
#include <asm/nand.h>
+#include <asm/portmux.h>
#include <linux/spi/ad7877.h>
/*
};
#endif
+#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+ && defined(CONFIG_SND_SOC_WM8731_SPI)
+static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
.platform_data = &bfin_ad7877_ts_info,
.irq = IRQ_PF6,
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7877_chip_info,
},
#endif
+#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
+ && defined(CONFIG_SND_SOC_WM8731_SPI)
+ {
+ .modalias = "wm8731",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 5,
+ .controller_data = &spi_wm8731_chip_info,
+ .mode = SPI_MODE_0,
+ },
+#endif
};
/* SPI controller data */
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
/* SPI (0) */
if ((bfin_read_SYSCR() & 0x7) == 0x3)
bfin_gpio_reset_spi0_ssel1();
}
+
+/*
+ * Currently the MAC address is saved in Flash by U-Boot
+ */
+#define FLASH_MAC 0x203f0000
+void bfin_get_ether_addr(char *addr)
+{
+ *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
+ *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
if (BF533 || BF532 || BF531)
+source "arch/blackfin/mach-bf533/boards/Kconfig"
+
menu "BF533/2/1 Specific Configuration"
comment "Interrupt Priority Assignment"
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
*/
const char bfin_board_name[] = "HV Sistemas H8606";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_BFIN_MODULE)
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
.end = IRQ_PROG_INTB,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}, {
- /*
- * denotes the flag pin and is used directly if
- * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
- */
.start = IRQ_PF7,
.end = IRQ_PF7,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
return 0;
}
-arch_initcall(H8606_init);
\ No newline at end of file
+arch_initcall(H8606_init);
--- /dev/null
+choice
+ prompt "System type"
+ default BFIN533_STAMP
+ help
+ Select your board!
+
+config BFIN533_EZKIT
+ bool "BF533-EZKIT"
+ help
+ BF533-EZKIT-LITE board support.
+
+config BFIN533_STAMP
+ bool "BF533-STAMP"
+ help
+ BF533-STAMP board support.
+
+config BFIN533_BLUETECHNIX_CM
+ bool "Bluetechnix CM-BF533"
+ depends on (BF533)
+ help
+ CM-BF533 support for EVAL- and DEV-Board.
+
+config H8606_HVSISTEMAS
+ bool "HV Sistemas H8606"
+ depends on (BF532)
+ help
+ HV Sistemas H8606 board support.
+
+config GENERIC_BF533_BOARD
+ bool "Generic"
+ help
+ Generic or Custom board support.
+
+endchoice
# arch/blackfin/mach-bf533/boards/Makefile
#
-obj-$(CONFIG_GENERIC_BOARD) += generic_board.o
+obj-$(CONFIG_GENERIC_BF533_BOARD) += generic_board.o
obj-$(CONFIG_BFIN533_STAMP) += stamp.o
obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o
obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
.end = IRQ_PROG_INTB,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}, {
- /*
- * denotes the flag pin and is used directly if
- * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
- */
.start = IRQ_PF7,
.end = IRQ_PF7,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
if (BF537 || BF534 || BF536)
+source "arch/blackfin/mach-bf537/boards/Kconfig"
+
menu "BF537 Specific Configuration"
comment "Interrupt Priority Assignment"
--- /dev/null
+choice
+ prompt "System type"
+ default BFIN537_STAMP
+ help
+ Select your board!
+
+config BFIN537_STAMP
+ bool "BF537-STAMP"
+ help
+ BF537-STAMP board support.
+
+config BFIN537_BLUETECHNIX_CM
+ bool "Bluetechnix CM-BF537"
+ depends on (BF537)
+ help
+ CM-BF537 support for EVAL- and DEV-Board.
+
+config PNAV10
+ bool "PNAV board"
+ depends on (BF537)
+ help
+ PNAV board support.
+
+config GENERIC_BF537_BOARD
+ bool "Generic"
+ help
+ Generic or Custom board support.
+
+endchoice
# arch/blackfin/mach-bf537/boards/Makefile
#
-obj-y += eth_mac.o
-obj-$(CONFIG_GENERIC_BOARD) += generic_board.o
-obj-$(CONFIG_BFIN537_STAMP) += stamp.o led.o
-obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o
-obj-$(CONFIG_PNAV10) += pnav10.o
+obj-$(CONFIG_GENERIC_BF537_BOARD) += generic_board.o
+obj-$(CONFIG_BFIN537_STAMP) += stamp.o led.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o
+obj-$(CONFIG_PNAV10) += pnav10.o
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
}
arch_initcall(cm_bf537_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+ random_ether_addr(addr);
+ printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
+++ /dev/null
-/*
- * arch/blackfin/mach-bf537/board/eth_mac.c
- *
- * Copyright (C) 2007 Analog Devices, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#include <linux/module.h>
-#include <asm/blackfin.h>
-
-#if defined(CONFIG_GENERIC_BOARD) || defined(CONFIG_BFIN537_STAMP)
-
-/*
- * Currently the MAC address is saved in Flash by U-Boot
- */
-#define FLASH_MAC 0x203f0000
-
-void get_bf537_ether_addr(char *addr)
-{
- unsigned int flash_mac = (unsigned int) FLASH_MAC;
- *(u32 *)(&(addr[0])) = bfin_read32(flash_mac);
- flash_mac += 4;
- *(u16 *)(&(addr[4])) = bfin_read16(flash_mac);
-}
-
-#else
-
-/*
- * Provide MAC address function for other specific board setting
- */
-void get_bf537_ether_addr(char *addr)
-{
- printk(KERN_WARNING "%s: No valid Ethernet MAC address found\n", __FILE__);
-}
-
-#endif
-
-EXPORT_SYMBOL(get_bf537_ether_addr);
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
+#include <asm/portmux.h>
#include <linux/spi/ad7877.h>
/*
.platform_data = &bfin_ad7877_ts_info,
.irq = IRQ_PF6,
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7877_chip_info,
},
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
/* SPI (0) */
if ((bfin_read_SYSCR() & 0x7) == 0x3)
bfin_gpio_reset_spi0_ssel1();
}
+
+void bfin_get_ether_addr(char *addr)
+{
+ random_ether_addr(addr);
+ printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
#include <linux/usb/sl811.h>
#include <linux/spi/ad7877.h>
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
- .cs_change_per_word = 1,
+ .cs_change_per_word = 0,
.enable_dma = 0,
.bits_per_word = 16,
};
.platform_data = &bfin_ad7877_ts_info,
.irq = IRQ_PF2,
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 5,
.controller_data = &spi_ad7877_chip_info,
},
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
}
arch_initcall(stamp_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+ random_ether_addr(addr);
+ printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#endif
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
+#include <asm/portmux.h>
#include <linux/spi/ad7877.h>
/*
};
#endif
+#if defined(CONFIG_AX88180) || defined(CONFIG_AX88180_MODULE)
+static struct resource ax88180_resources[] = {
+ [0] = {
+ .start = 0x20300000,
+ .end = 0x20300000 + 0x8000,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_PF7,
+ .end = IRQ_PF7,
+ .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL),
+ },
+};
+
+static struct platform_device ax88180_device = {
+ .name = "ax88180",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(ax88180_resources),
+ .resource = ax88180_resources,
+};
+#endif
+
#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
static struct resource sl811_hcd_resources[] = {
{
.platform_data = &bfin_ad7877_ts_info,
.irq = IRQ_PF6,
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 1,
+ .bus_num = 0,
.chip_select = 1,
.controller_data = &spi_ad7877_chip_info,
},
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
/* SPI (0) */
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
{
.start = 0xFFC00400,
.end = 0xFFC004FF,
.flags = IORESOURCE_MEM,
- }, {
+ },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ {
.start = 0xFFC02000,
.end = 0xFFC020FF,
.flags = IORESOURCE_MEM,
},
+#endif
};
static struct platform_device bfin_uart_device = {
&dm9000_device,
#endif
+#if defined(CONFIG_AX88180) || defined(CONFIG_AX88180_MODULE)
+ &ax88180_device,
+#endif
+
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
&bfin_mac_device,
#endif
if ((bfin_read_SYSCR() & 0x7) == 0x3)
bfin_gpio_reset_spi0_ssel1();
}
+
+/*
+ * Currently the MAC address is saved in Flash by U-Boot
+ */
+#define FLASH_MAC 0x203f0000
+void bfin_get_ether_addr(char *addr)
+{
+ *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
+ *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
if (BF54x)
+source "arch/blackfin/mach-bf548/boards/Kconfig"
+
menu "BF548 Specific Configuration"
config DEB_DMA_URGENT
--- /dev/null
+choice
+ prompt "System type"
+ default BFIN548_EZKIT
+ help
+ Select your board!
+
+config BFIN548_EZKIT
+ bool "BF548-EZKIT"
+ help
+ BFIN548-EZKIT board support.
+
+endchoice
# arch/blackfin/mach-bf548/boards/Makefile
#
-obj-$(CONFIG_BFIN548_EZKIT) += ezkit.o led.o
+obj-$(CONFIG_BFIN548_EZKIT) += ezkit.o led.o
#include <asm/dma.h>
#include <asm/gpio.h>
#include <asm/nand.h>
+#include <asm/portmux.h>
#include <asm/mach/bf54x_keys.h>
#include <linux/input.h>
#include <linux/spi/ad7877.h>
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
- .cs_change_per_word = 1,
+ .cs_change_per_word = 0,
.enable_dma = 0,
.bits_per_word = 16,
};
};
/* SPI controller data */
-static struct bfin5xx_spi_master bf54x_spi_master_info = {
+static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bf54x_spi_master0 = {
.num_resources = ARRAY_SIZE(bfin_spi0_resource),
.resource = bfin_spi0_resource,
.dev = {
- .platform_data = &bf54x_spi_master_info, /* Passed to driver */
+ .platform_data = &bf54x_spi_master_info0, /* Passed to driver */
},
};
+static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
+};
+
static struct platform_device bf54x_spi_master1 = {
.name = "bfin-spi",
.id = 1, /* Bus number */
.num_resources = ARRAY_SIZE(bfin_spi1_resource),
.resource = bfin_spi1_resource,
.dev = {
- .platform_data = &bf54x_spi_master_info, /* Passed to driver */
+ .platform_data = &bf54x_spi_master_info1, /* Passed to driver */
},
};
#endif /* spi master and devices */
.resource = bfin_twi0_resource,
};
+#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
static struct resource bfin_twi1_resource[] = {
[0] = {
.start = TWI1_REGBASE,
.resource = bfin_twi1_resource,
};
#endif
+#endif
static struct platform_device *ezkit_devices[] __initdata = {
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
&i2c_bfin_twi0_device,
+#if !defined(CONFIG_BF542)
&i2c_bfin_twi1_device,
#endif
+#endif
};
static int __init stamp_init(void)
w[p2] = r0;
ssync;
+ p2.h = hi(EBIU_MBSCTL);
+ p2.l = lo(EBIU_MBSCTL);
+ r0.h = hi(CONFIG_EBIU_MBSCTLVAL);
+ r0.l = lo(CONFIG_EBIU_MBSCTLVAL);
+ [p2] = r0;
+ ssync;
+
+ p2.h = hi(EBIU_MODE);
+ p2.l = lo(EBIU_MODE);
+ r0.h = hi(CONFIG_EBIU_MODEVAL);
+ r0.l = lo(CONFIG_EBIU_MODEVAL);
+ [p2] = r0;
+ ssync;
+
+ p2.h = hi(EBIU_FCTL);
+ p2.l = lo(EBIU_FCTL);
+ r0.h = hi(CONFIG_EBIU_FCTLVAL);
+ r0.l = lo(CONFIG_EBIU_FCTLVAL);
+ [p2] = r0;
+ ssync;
+
/* This section keeps the processor in supervisor mode
* during kernel boot. Switches to user mode at end of boot.
* See page 3-9 of Hardware Reference manual for documentation.
-if BF561
+if (BF561)
+
+source "arch/blackfin/mach-bf561/boards/Kconfig"
menu "BF561 Specific Configuration"
--- /dev/null
+choice
+ prompt "System type"
+ default BFIN561_EZKIT
+ help
+ Select your board!
+
+config BFIN561_EZKIT
+ bool "BF561-EZKIT"
+ help
+ BF561-EZKIT-LITE board support.
+
+config BFIN561_TEPLA
+ bool "BF561-TEPLA"
+ help
+ BF561-TEPLA board support.
+
+config BFIN561_BLUETECHNIX_CM
+ bool "Bluetechnix CM-BF561"
+ help
+ CM-BF561 support for EVAL- and DEV-Board.
+
+config GENERIC_BF561_BOARD
+ bool "Generic"
+ help
+ Generic or Custom board support.
+
+endchoice
# arch/blackfin/mach-bf561/boards/Makefile
#
-obj-$(CONFIG_GENERIC_BOARD) += generic_board.o
+obj-$(CONFIG_GENERIC_BF561_BOARD) += generic_board.o
obj-$(CONFIG_BFIN561_BLUETECHNIX_CM) += cm_bf561.o
obj-$(CONFIG_BFIN561_EZKIT) += ezkit.o
obj-$(CONFIG_BFIN561_TEPLA) += tepla.o
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <linux/usb_isp1362.h>
+#include <linux/usb/isp1362.h>
#include <linux/pata_platform.h>
#include <linux/irq.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
#include <linux/pata_platform.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
/*
* Name the Board for the /proc/cpuinfo
};
#endif
+#if defined(CONFIG_AX88180) || defined(CONFIG_AX88180_MODULE)
+static struct resource ax88180_resources[] = {
+ [0] = {
+ .start = 0x2c000000,
+ .end = 0x2c000000 + 0x8000,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_PF10,
+ .end = IRQ_PF10,
+ .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL),
+ },
+};
+
+static struct platform_device ax88180_device = {
+ .name = "ax88180",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(ax88180_resources),
+ .resource = ax88180_resources,
+};
+#endif
+
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
static struct resource bfin_uart_resources[] = {
{
static struct bfin5xx_spi_master bfin_spi0_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device bfin_spi0_device = {
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
&smc91x_device,
#endif
+
+#if defined(CONFIG_AX88180) || defined(CONFIG_AX88180_MODULE)
+ &ax88180_device,
+#endif
+
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&bfin_spi0_device,
#endif
.end = IRQ_PROG_INTB,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}, {
- /*
- * denotes the flag pin and is used directly if
- * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
- */
.start = IRQ_PF9,
.end = IRQ_PF9,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
.end = IRQ_PROG_INTB,
.flags = IORESOURCE_IRQ|IORESOURCE_IRQ_HIGHLEVEL,
}, {
- /*
- * denotes the flag pin and is used directly if
- * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
- */
.start = IRQ_PF7,
.end = IRQ_PF7,
.flags = IORESOURCE_IRQ|IORESOURCE_IRQ_HIGHLEVEL,
} else
buf += sprintf(buf, "Data CPLB entry:\n");
- buf += sprintf(buf, "Address\t\tData\tSize\tValid\tLocked\tSwapin\n\tiCount\toCount\n");
+ buf += sprintf(buf, "Address\t\tData\tSize\tValid\tLocked\tSwapin\tiCount\toCount\n");
while (*p_addr != 0xffffffff) {
entry = cplb_find_entry(cplb_addr, cplb_data, *p_addr, *p_data);
/* ICPLB Miss Exception. We need to choose one of the
* currently-installed CPLBs, and replace it with one
* from the configuration table.
- */
+ */
P4.L = LO(ICPLB_FAULT_ADDR);
P4.H = HI(ICPLB_FAULT_ADDR);
/* See if failed address > start address */
CC = R4 <= R0(IU);
- IF !CC JUMP .Linext;
+ IF !CC JUMP .Linext;
/* extract page size (17:16)*/
R3 = EXTRACT(R2, R1.L) (Z);
/* FAILED CASES*/
.Lno_page_in_table:
- ( R7:4,P5:3 ) = [SP++];
R0 = CPLB_NO_ADDR_MATCH;
- RTS;
+ JUMP .Lfail_ret;
+
.Lall_locked:
- ( R7:4,P5:3 ) = [SP++];
R0 = CPLB_NO_UNLOCKED;
- RTS;
+ JUMP .Lfail_ret;
+
.Lprot_violation:
- ( R7:4,P5:3 ) = [SP++];
R0 = CPLB_PROT_VIOL;
+
+.Lfail_ret:
+ /* Make sure we turn protection/cache back on, even in the failing case */
+ BITSET(R5,ENICPLB_P);
+ CLI R2;
+ SSYNC; /* SSYNC required before writing to IMEM_CONTROL. */
+ .align 8;
+ [P4] = R5;
+ SSYNC;
+ STI R2;
+
+ ( R7:4,P5:3 ) = [SP++];
RTS;
.Ldcplb_write:
* after a timer-interrupt and after each system call.
*/
-
+#include <linux/init.h>
#include <linux/linkage.h>
#include <linux/unistd.h>
#include <asm/blackfin.h>
* This one does not lower the level to IRQ5, and thus can be used to
* patch up CPLB misses on the kernel stack.
*/
-ENTRY(_ex_dcplb)
#if ANOMALY_05000261
+#define _ex_dviol _ex_workaround_261
+#define _ex_dmiss _ex_workaround_261
+#define _ex_dmult _ex_workaround_261
+
+ENTRY(_ex_workaround_261)
/*
* Work around an anomaly: if we see a new DCPLB fault, return
* without doing anything. Then, if we get the same fault again,
* handle it.
*/
+ P4 = R7; /* Store EXCAUSE */
p5.l = _last_cplb_fault_retx;
p5.h = _last_cplb_fault_retx;
r7 = [p5];
r6 = retx;
[p5] = r6;
cc = r6 == r7;
- if !cc jump _return_from_exception;
+ if !cc jump _bfin_return_from_exception;
/* fall through */
+ R7 = P4;
+ R6 = 0x26; /* Data CPLB Miss */
+ cc = R6 == R7;
+ if cc jump _ex_dcplb_miss (BP);
+ /* Handle 0x23 Data CPLB Protection Violation
+ * and Data CPLB Multiple Hits - Linux Trap Zero
+ */
+ jump _ex_trap_c;
+ENDPROC(_ex_workaround_261)
+
+#else
+#define _ex_dviol _ex_trap_c
+#define _ex_dmiss _ex_dcplb_miss
+#define _ex_dmult _ex_trap_c
#endif
-ENDPROC(_ex_dcplb)
-ENTRY(_ex_icplb)
+ENTRY(_ex_dcplb_miss)
+ENTRY(_ex_icplb_miss)
(R7:6,P5:4) = [sp++];
ASTAT = [sp++];
SAVE_ALL_SYS
RESTORE_ALL_SYS
SP = EX_SCRATCH_REG;
rtx;
-ENDPROC(_ex_icplb)
+ENDPROC(_ex_icplb_miss)
ENTRY(_ex_syscall)
DEBUG_START_HWTRACE(p5, r7)
r7 = retx;
r6 = reti;
cc = r7 == r6;
- if cc jump _return_from_exception
+ if cc jump _bfin_return_from_exception
r7 = syscfg;
bitclr (r7, 0);
syscfg = R7;
r7 = [p4];
cc = r6 == r7;
if !cc jump _ex_trap_c;
+ENDPROC(_ex_single_step)
-ENTRY(_return_from_exception)
+ENTRY(_bfin_return_from_exception)
DEBUG_START_HWTRACE(p5, r7)
#if ANOMALY_05000257
R7=LC0;
ASTAT = [sp++];
sp = EX_SCRATCH_REG;
rtx;
-ENDPROC(_ex_soft_bp)
+ENDPROC(_bfin_return_from_exception)
ENTRY(_handle_bad_cplb)
/* To get here, we just tried and failed to change a CPLB
LC0 = [sp++];
P2 = [sp++];
P3 = [sp++];
- jump _return_from_exception;
+ jump _bfin_return_from_exception;
ENDPROC(_ex_trace_buff_full)
#if CONFIG_DEBUG_BFIN_HWTRACE_EXPAND_LEN == 4
#endif /* CONFIG_DEBUG_BFIN_HWTRACE_EXPAND */
#if CONFIG_EARLY_PRINTK
-.section .init.text
+__INIT
ENTRY(_early_trap)
SAVE_ALL_SYS
trace_buffer_stop(p0,r0);
call _early_trap_c;
SP += 12;
ENDPROC(_early_trap)
+__FINIT
#endif /* CONFIG_EARLY_PRINTK */
/*
#else
.data
#endif
+
ENTRY(_ex_table)
/* entry for each EXCAUSE[5:0]
* This table must be in sync with the table in ./kernel/traps.c
.long _ex_trap_c /* 0x20 - Reserved */
.long _ex_trap_c /* 0x21 - Undefined Instruction */
.long _ex_trap_c /* 0x22 - Illegal Instruction Combination */
- .long _ex_dcplb /* 0x23 - Data CPLB Protection Violation */
+ .long _ex_dviol /* 0x23 - Data CPLB Protection Violation */
.long _ex_trap_c /* 0x24 - Data access misaligned */
.long _ex_trap_c /* 0x25 - Unrecoverable Event */
- .long _ex_dcplb /* 0x26 - Data CPLB Miss */
- .long _ex_trap_c /* 0x27 - Data CPLB Multiple Hits - Linux Trap Zero */
+ .long _ex_dmiss /* 0x26 - Data CPLB Miss */
+ .long _ex_dmult /* 0x27 - Data CPLB Multiple Hits - Linux Trap Zero */
.long _ex_trap_c /* 0x28 - Emulation Watchpoint */
.long _ex_trap_c /* 0x29 - Instruction fetch access error (535 only) */
.long _ex_trap_c /* 0x2A - Instruction fetch misaligned */
- .long _ex_icplb /* 0x2B - Instruction CPLB protection Violation */
- .long _ex_icplb /* 0x2C - Instruction CPLB miss */
+ .long _ex_trap_c /* 0x2B - Instruction CPLB protection Violation */
+ .long _ex_icplb_miss /* 0x2C - Instruction CPLB miss */
.long _ex_trap_c /* 0x2D - Instruction CPLB Multiple Hits */
.long _ex_trap_c /* 0x2E - Illegal use of Supervisor Resource */
.long _ex_trap_c /* 0x2E - Illegal use of Supervisor Resource */
#include <asm/blackfin.h>
#include <asm/mach/irq.h>
-#include <linux/autoconf.h>
#include <linux/linkage.h>
#include <asm/entry.h>
#include <asm/asm-offsets.h>
.unmask = bf561_internal_unmask_irq,
};
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
static unsigned short gpio_enabled[gpio_bank(MAX_BLACKFIN_GPIOS)];
static unsigned short gpio_edge_triggered[gpio_bank(MAX_BLACKFIN_GPIOS)];
}
-#endif /* CONFIG_IRQCHIP_DEMUX_GPIO */
-
void __init init_exception_vectors(void)
{
SSYNC();
set_irq_chip(irq, &bf561_core_irqchip);
else
set_irq_chip(irq, &bf561_internal_irqchip);
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
+
if ((irq != IRQ_PROG0_INTA) &&
- (irq != IRQ_PROG1_INTA) && (irq != IRQ_PROG2_INTA)) {
-#endif
+ (irq != IRQ_PROG1_INTA) &&
+ (irq != IRQ_PROG2_INTA))
set_irq_handler(irq, handle_simple_irq);
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
- } else {
+ else
set_irq_chained_handler(irq, bf561_demux_gpio_irq);
- }
-#endif
-
}
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
for (irq = IRQ_PF0; irq <= IRQ_PF47; irq++) {
set_irq_chip(irq, &bf561_gpio_irqchip);
/* if configured as edge, then will be changed to do_edge_IRQ */
set_irq_handler(irq, handle_level_irq);
}
-#endif
+
bfin_write_IMASK(0);
CSYNC();
ilat = bfin_read_ILAT();
}
#ifdef CONFIG_DO_IRQ_L1
-void do_irq(int vec, struct pt_regs *fp)__attribute__((l1_text));
+__attribute__((l1_text))
#endif
-
void do_irq(int vec, struct pt_regs *fp)
{
if (vec == EVT_IVTMR_P) {
}
#endif /* BF537_GENERIC_ERROR_INT_DEMUX */
-#if defined(CONFIG_IRQCHIP_DEMUX_GPIO) && !defined(CONFIG_BF54x)
+#if !defined(CONFIG_BF54x)
static unsigned short gpio_enabled[gpio_bank(MAX_BLACKFIN_GPIOS)];
static unsigned short gpio_edge_triggered[gpio_bank(MAX_BLACKFIN_GPIOS)];
}
}
-#else /* CONFIG_IRQCHIP_DEMUX_GPIO */
+#else /* CONFIG_BF54x */
#define NR_PINT_SYS_IRQS 4
#define NR_PINT_BITS 32
}
}
-#endif /* CONFIG_IRQCHIP_DEMUX_GPIO */
+#endif
void __init init_exception_vectors(void)
{
bfin_write_SIC_IMASK1(SIC_UNMASK_ALL);
bfin_write_SIC_IWR0(IWR_ENABLE_ALL);
bfin_write_SIC_IWR1(IWR_ENABLE_ALL);
-#ifdef CONFIG_BF54x
+# ifdef CONFIG_BF54x
bfin_write_SIC_IMASK2(SIC_UNMASK_ALL);
bfin_write_SIC_IWR2(IWR_ENABLE_ALL);
-#endif
+# endif
#else
bfin_write_SIC_IMASK(SIC_UNMASK_ALL);
bfin_write_SIC_IWR(IWR_ENABLE_ALL);
local_irq_disable();
-#if defined(CONFIG_IRQCHIP_DEMUX_GPIO) && defined(CONFIG_BF54x)
-#ifdef CONFIG_PINTx_REASSIGN
+#ifdef CONFIG_BF54x
+# ifdef CONFIG_PINTx_REASSIGN
pint[0]->assign = CONFIG_PINT0_ASSIGN;
pint[1]->assign = CONFIG_PINT1_ASSIGN;
pint[2]->assign = CONFIG_PINT2_ASSIGN;
pint[3]->assign = CONFIG_PINT3_ASSIGN;
-#endif
+# endif
/* Whenever PINTx_ASSIGN is altered init_pint_lut() must be executed! */
init_pint_lut();
#endif
#endif
switch (irq) {
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#if defined(CONFIG_BF53x)
case IRQ_PROG_INTA:
set_irq_chained_handler(irq,
bfin_demux_gpio_irq);
break;
-#if defined(BF537_FAMILY) && !(defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE))
+# if defined(BF537_FAMILY) && !(defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE))
case IRQ_MAC_RX:
set_irq_chained_handler(irq,
bfin_demux_gpio_irq);
break;
-#endif
+# endif
#elif defined(CONFIG_BF54x)
case IRQ_PINT0:
set_irq_chained_handler(irq,
set_irq_chained_handler(irq,
bfin_demux_gpio_irq);
break;
-#endif
#endif
default:
set_irq_handler(irq, handle_simple_irq);
}
#endif
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#ifndef CONFIG_BF54x
for (irq = IRQ_PF0; irq < NR_IRQS; irq++) {
#else
/* if configured as edge, then will be changed to do_edge_IRQ */
set_irq_handler(irq, handle_level_irq);
}
-#endif
+
bfin_write_IMASK(0);
CSYNC();
ilat = bfin_read_ILAT();
}
#ifdef CONFIG_DO_IRQ_L1
-void do_irq(int vec, struct pt_regs *fp) __attribute__((l1_text));
+__attribute__((l1_text))
#endif
-
void do_irq(int vec, struct pt_regs *fp)
{
if (vec == EVT_IVTMR_P) {
case (SEQSTAT_HWERRCAUSE_SYSTEM_MMR): /* System MMR Error */
info.si_code = BUS_ADRALN;
sig = SIGBUS;
- printk(KERN_EMERG HWC_x2);
+ printk(KERN_EMERG HWC_x2(KERN_EMERG));
break;
case (SEQSTAT_HWERRCAUSE_EXTERN_ADDR): /* External Memory Addressing Error */
info.si_code = BUS_ADRERR;
sig = SIGBUS;
- printk(KERN_EMERG HWC_x3);
+ printk(KERN_EMERG HWC_x3(KERN_EMERG));
break;
case (SEQSTAT_HWERRCAUSE_PERF_FLOW): /* Performance Monitor Overflow */
- printk(KERN_EMERG HWC_x12);
+ printk(KERN_EMERG HWC_x12(KERN_EMERG));
break;
case (SEQSTAT_HWERRCAUSE_RAISE_5): /* RAISE 5 instruction */
- printk(KERN_EMERG HWC_x18);
+ printk(KERN_EMERG HWC_x18(KERN_EMERG));
break;
default: /* Reserved */
- printk(KERN_EMERG HWC_default);
+ printk(KERN_EMERG HWC_default(KERN_EMERG));
break;
}
}
regs->ipend = bfin_read_IPEND();
- dump_bfin_regs(regs, (void *)regs->pc);
+ dump_bfin_process(regs);
+ dump_bfin_mem((void *)regs->pc);
+ show_regs(regs);
if (0 == (info.si_signo = sig) || 0 == user_mode(regs)) /* in kernelspace */
panic("Unhandled IRQ or exceptions!\n");
else { /* in userspace */
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#include <linux/autoconf.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
loopback. Not all products are able to do this in software only.
Axis 2400/2401 must disable receiver.
-config ETRAX_IDE
- bool "ATA/IDE support"
- select IDE
- select BLK_DEV_IDE
- select BLK_DEV_IDEDISK
- select BLK_DEV_IDECD
- select BLK_DEV_IDEDMA
- select IDE_GENERIC
- help
- Enable this to get support for ATA/IDE.
- You can't use parallel ports or SCSI ports
- at the same time.
-
-
-config ETRAX_IDE_DELAY
- int "Delay for drives to regain consciousness"
- depends on ETRAX_IDE
- default 15
- help
- Number of seconds to wait for IDE drives to spin up after an IDE
- reset.
-choice
- prompt "IDE reset pin"
- depends on ETRAX_IDE
- default ETRAX_IDE_PB7_RESET
-
-config ETRAX_IDE_PB7_RESET
- bool "Port_PB_Bit_7"
- help
- IDE reset on pin 7 on port B
-
-config ETRAX_IDE_G27_RESET
- bool "Port_G_Bit_27"
- help
- IDE reset on pin 27 on port G
-
-endchoice
-
-
config ETRAX_USB_HOST
bool "USB host"
select USB
that a user can change the value on using ioctl's.
Bit set = changeable.
-config ETRAX_IDE
- bool "ATA/IDE support"
- depends on ETRAX_ARCH_V32
- select IDE
- select BLK_DEV_IDE
- select BLK_DEV_IDEDISK
- select BLK_DEV_IDECD
- select BLK_DEV_IDEDMA
- select IDE_GENERIC
- help
- Enables the ETRAX IDE driver.
-
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
unsigned long r2, unsigned long r3, unsigned long r4,
unsigned long r5, unsigned long r6, struct pt_regs *regs)
{
- sigset_t saveset, newset;
+ sigset_t newset;
/* XXX: Don't preclude handling different sized sigset_t's. */
if (sigsetsize != sizeof(sigset_t))
if (copy_from_user(&newset, unewset, sizeof(newset)))
return -EFAULT;
- sigdelsetmask(&newset, ~_BLOCKABLE);
+ sigdelsetmask(&newset, sigmask(SIGKILL)|sigmask(SIGSTOP));
spin_lock_irq(¤t->sighand->siglock);
- saveset = current->blocked;
+ current->saved_sigmask = current->blocked;
current->blocked = newset;
recalc_sigpending();
spin_unlock_irq(¤t->sighand->siglock);
- regs->r0 = -EINTR;
- while (1) {
- current->state = TASK_INTERRUPTIBLE;
- schedule();
- if (do_signal(regs, &saveset))
- return regs->r0;
- }
+ current->state = TASK_INTERRUPTIBLE;
+ schedule();
+ set_thread_flag(TIF_RESTORE_SIGMASK);
+ return -ERESTARTNOHAND;
}
asmlinkage int
.long sys_mq_getsetattr
.long sys_ni_syscall /* reserved for kexec */
.long sys_waitid
+ .long sys_ni_syscall /* 285 */ /* available */
+ .long sys_add_key
+ .long sys_request_key
+ .long sys_keyctl
+ .long sys_ioprio_set
+ .long sys_ioprio_get /* 290 */
+ .long sys_inotify_init
+ .long sys_inotify_add_watch
+ .long sys_inotify_rm_watch
+ .long sys_migrate_pages
+ .long sys_openat /* 295 */
+ .long sys_mkdirat
+ .long sys_mknodat
+ .long sys_fchownat
+ .long sys_futimesat
+ .long sys_fstatat64 /* 300 */
+ .long sys_unlinkat
+ .long sys_renameat
+ .long sys_linkat
+ .long sys_symlinkat
+ .long sys_readlinkat /* 305 */
+ .long sys_fchmodat
+ .long sys_faccessat
+ .long sys_pselect6
+ .long sys_ppoll
+ .long sys_unshare /* 310 */
+ .long sys_set_robust_list
+ .long sys_get_robust_list
+ .long sys_splice
+ .long sys_sync_file_range
+ .long sys_tee /* 315 */
+ .long sys_vmsplice
+ .long sys_move_pages
+ .long sys_getcpu
+ .long sys_epoll_pwait
+ .long sys_utimensat /* 320 */
+ .long sys_signalfd
+ .long sys_timerfd
+ .long sys_eventfd
+ .long sys_fallocate
static int atari_keyb_done = 0;
-int __init atari_keyb_init(void)
+int atari_keyb_init(void)
{
if (atari_keyb_done)
return 0;
atari_keyb_done = 1;
return 0;
}
+EXPORT_SYMBOL_GPL(atari_keyb_init);
int atari_kbd_translate(unsigned char keycode, unsigned char *keycodep, char raw_mode)
{
config BASLER_EXCITE
bool "Basler eXcite smart camera"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
config BCM47XX
bool "BCM47XX based boards"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
config MIPS_COBALT
bool "Cobalt Server"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_GT641XX
select DMA_NONCOHERENT
select HW_HAS_PCI
bool "DECstations"
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select NO_IOPORT
select IRQ_CPU
select ARC32
select ARCH_MAY_HAVE_PC_FDC
select CEVT_R4K
+ select CSRC_R4K
select GENERIC_ISA_DMA
select IRQ_CPU
select I8253
config LASAT
bool "LASAT Networks platforms"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select HW_HAS_PCI
bool "Lemote Fulong mini-PC"
select ARCH_SPARSEMEM_ENABLE
select CEVT_R4K
+ select CSRC_R4K
select SYS_HAS_CPU_LOONGSON2
select DMA_NONCOHERENT
select BOOT_ELF32
bool "MIPS Atlas board"
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select IRQ_CPU
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select IRQ_CPU
config MIPS_SEAD
bool "MIPS SEAD board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
config MIPS_SIM
bool 'MIPS simulator (MIPSsim)'
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select IRQ_CPU
config MARKEINS
bool "NEC EMMA2RH Mark-eins"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
config MACH_VR41XX
bool "NEC VR4100 series based machines"
select CEVT_R4K
+ select CSRC_R4K
select SYS_HAS_CPU_VR41XX
select GENERIC_HARDIRQS_NO__DO_IRQ
config PMC_YOSEMITE
bool "PMC-Sierra Yosemite eval board"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
config QEMU
bool "Qemu"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select GENERIC_ISA_DMA
select HAVE_STD_PC_SERIAL_PORT
select ARC32
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_EISA
select I8253
+ select I8259
select IP22_CPU_SCACHE
select IRQ_CPU
select GENERIC_ISA_DMA_SUPPORT_BROKEN
select ARC32
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select ZONE_DMA32 if 64BIT
config SIBYTE_LITTLESUR
bool "Sibyte BCM91250C2-LittleSur"
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select ZONE_DMA32 if 64BIT
config SNI_RM
bool "SNI RM200/300/400"
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select HW_HAS_EISA
config TOSHIBA_RBTX4927
bool "Toshiba RBTX49[23]7 board"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_TXX9
select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
config TOSHIBA_RBTX4938
bool "Toshiba RBTX4938 board"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_TXX9
select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
config WR_PPMC
bool "Wind River PPMC board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select BOOT_ELF32
select DMA_NONCOHERENT
config CSRC_BCM1480
bool
+config CSRC_R4K
+ bool
+
config CSRC_SB1250
bool
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
+config ARCH_POPULATES_NODE_MAP
+ def_bool y
+
config ARCH_SPARSEMEM_ENABLE
bool
select SPARSEMEM_STATIC
config PCSPEAKER
bool
+config ZONE_DMA32
+ bool
+
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
bool
select 64BIT_PHYS_ADDR
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
obj-$(CONFIG_CEVT_SB1250) += cevt-sb1250.o
obj-$(CONFIG_CEVT_TXX9) += cevt-txx9.o
obj-$(CONFIG_CSRC_BCM1480) += csrc-bcm1480.o
+obj-$(CONFIG_CSRC_R4K) += csrc-r4k.o
obj-$(CONFIG_CSRC_SB1250) += csrc-sb1250.o
binfmt_irix-objs := irixelf.o irixinv.o irixioctl.o irixsig.o \
obj-$(CONFIG_CPU_VR41XX) += r4k_fpu.o r4k_switch.o
obj-$(CONFIG_SMP) += smp.o
+obj-$(CONFIG_SMP_UP) += smp-up.o
obj-$(CONFIG_MIPS_MT) += mips-mt.o
obj-$(CONFIG_MIPS_MT_FPAFF) += mips-mt-fpaff.o
return 1;
}
-void __cpuinit mips_clockevent_init(void)
+int __cpuinit mips_clockevent_init(void)
{
uint64_t mips_freq = mips_hpt_frequency;
unsigned int cpu = smp_processor_id();
unsigned int irq;
if (!cpu_has_counter || !mips_hpt_frequency)
- return;
+ return -ENXIO;
#ifdef CONFIG_MIPS_MT_SMTC
setup_smtc_dummy_clockevent_device();
* device.
*/
if (cpu)
- return;
+ return 0;
#endif
if (!c0_compare_int_usable())
- return;
+ return -ENXIO;
/*
* With vectored interrupts things are getting platform specific.
clockevents_register_device(cd);
- if (!cp0_timer_irq_installed)
- return;
+ if (cp0_timer_irq_installed)
+ return 0;
cp0_timer_irq_installed = 1;
#else
setup_irq(irq, &c0_compare_irqaction);
#endif
+
+ return 0;
}
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+
+static cycle_t c0_hpt_read(void)
+{
+ return read_c0_count();
+}
+
+static struct clocksource clocksource_mips = {
+ .name = "MIPS",
+ .read = c0_hpt_read,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static void __init init_mips_clocksource(void)
+{
+ /* Calclate a somewhat reasonable rating value */
+ clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
+
+ clocksource_set_clock(&clocksource_mips, mips_hpt_frequency);
+
+ clocksource_register(&clocksource_mips);
+}
static void __init bootmem_init(void)
{
- unsigned long reserved_end;
+ unsigned long init_begin, reserved_end;
unsigned long mapstart = ~0UL;
unsigned long bootmap_size;
int i;
*/
bootmap_size = init_bootmem_node(NODE_DATA(0), mapstart,
min_low_pfn, max_low_pfn);
+
+
+ init_begin = PFN_UP(__pa_symbol(&__init_begin));
+ for (i = 0; i < boot_mem_map.nr_map; i++) {
+ unsigned long start, end;
+
+ start = PFN_UP(boot_mem_map.map[i].addr);
+ end = PFN_DOWN(boot_mem_map.map[i].addr
+ + boot_mem_map.map[i].size);
+
+ if (start <= init_begin)
+ start = init_begin;
+ if (start >= end)
+ continue;
+
+#ifndef CONFIG_HIGHMEM
+ if (end > max_low_pfn)
+ end = max_low_pfn;
+
+ /*
+ * ... finally, is the area going away?
+ */
+ if (end <= start)
+ continue;
+#endif
+
+ add_active_range(0, start, end);
+ }
+
/*
* Register fully available low RAM pages with the bootmem allocator.
*/
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006, 07 by Ralf Baechle (ralf@linux-mips.org)
+ *
+ * Symmetric Uniprocessor (TM) Support
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+/*
+ * Send inter-processor interrupt
+ */
+void up_send_ipi_single(int cpu, unsigned int action)
+{
+ panic(KERN_ERR "%s called", __func__);
+}
+
+static inline void up_send_ipi_mask(cpumask_t mask, unsigned int action)
+{
+ panic(KERN_ERR "%s called", __func__);
+}
+
+/*
+ * After we've done initial boot, this function is called to allow the
+ * board code to clean up state, if needed
+ */
+void __cpuinit up_init_secondary(void)
+{
+}
+
+void __cpuinit up_smp_finish(void)
+{
+}
+
+/* Hook for after all CPUs are online */
+void up_cpus_done(void)
+{
+}
+
+/*
+ * Firmware CPU startup hook
+ */
+void __cpuinit up_boot_secondary(int cpu, struct task_struct *idle)
+{
+}
+
+void __init up_smp_setup(void)
+{
+}
+
+void __init up_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+struct plat_smp_ops up_smp_ops = {
+ .send_ipi_single = up_send_ipi_single,
+ .send_ipi_mask = up_send_ipi_mask,
+ .init_secondary = up_init_secondary,
+ .smp_finish = up_smp_finish,
+ .cpus_done = up_cpus_done,
+ .boot_secondary = up_boot_secondary,
+ .smp_setup = up_smp_setup,
+ .prepare_cpus = up_prepare_cpus,
+};
return rtc_mips_set_mmss(now.tv_sec);
}
-/*
- * High precision timer functions for a R4k-compatible timer.
- */
-static cycle_t c0_hpt_read(void)
-{
- return read_c0_count();
-}
-
int (*mips_timer_state)(void);
int null_perf_irq(void)
unsigned int mips_hpt_frequency;
-static struct clocksource clocksource_mips = {
- .name = "MIPS",
- .read = c0_hpt_read,
- .mask = CLOCKSOURCE_MASK(32),
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static unsigned int __init calibrate_hpt(void)
-{
- cycle_t frequency, hpt_start, hpt_end, hpt_count, hz;
-
- const int loops = HZ / 10;
- int log_2_loops = 0;
- int i;
-
- /*
- * We want to calibrate for 0.1s, but to avoid a 64-bit
- * division we round the number of loops up to the nearest
- * power of 2.
- */
- while (loops > 1 << log_2_loops)
- log_2_loops++;
- i = 1 << log_2_loops;
-
- /*
- * Wait for a rising edge of the timer interrupt.
- */
- while (mips_timer_state());
- while (!mips_timer_state());
-
- /*
- * Now see how many high precision timer ticks happen
- * during the calculated number of periods between timer
- * interrupts.
- */
- hpt_start = clocksource_mips.read();
- do {
- while (mips_timer_state());
- while (!mips_timer_state());
- } while (--i);
- hpt_end = clocksource_mips.read();
-
- hpt_count = (hpt_end - hpt_start) & clocksource_mips.mask;
- hz = HZ;
- frequency = hpt_count * hz;
-
- return frequency >> log_2_loops;
-}
-
void __init clocksource_set_clock(struct clocksource *cs, unsigned int clock)
{
u64 temp;
cd->mult = (u32) temp;
}
-static void __init init_mips_clocksource(void)
-{
- /* Calclate a somewhat reasonable rating value */
- clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
-
- clocksource_set_clock(&clocksource_mips, mips_hpt_frequency);
-
- clocksource_register(&clocksource_mips);
-}
-
void __init __weak plat_time_init(void)
{
}
BUG();
}
+static __init int cpu_has_mfc0_count_bug(void)
+{
+ switch (current_cpu_type()) {
+ case CPU_R4000PC:
+ case CPU_R4000SC:
+ case CPU_R4000MC:
+ /*
+ * V3.0 is documented as suffering from the mfc0 from count bug.
+ * Afaik this is the last version of the R4000. Later versions
+ * were marketed as R4400.
+ */
+ return 1;
+
+ case CPU_R4400PC:
+ case CPU_R4400SC:
+ case CPU_R4400MC:
+ /*
+ * The published errata for the R4400 upto 3.0 say the CPU
+ * has the mfc0 from count bug.
+ */
+ if ((current_cpu_data.processor_id & 0xff) <= 0x30)
+ return 1;
+
+ /*
+ * I don't have erratas for newer R4400 so be paranoid.
+ */
+ return 1;
+ }
+
+ return 0;
+}
+
void __init time_init(void)
{
plat_time_init();
- if (cpu_has_counter && (mips_hpt_frequency || mips_timer_state)) {
- /* We know counter frequency. Or we can get it. */
- if (!mips_hpt_frequency)
- mips_hpt_frequency = calibrate_hpt();
-
- /* Report the high precision timer rate for a reference. */
- printk("Using %u.%03u MHz high precision timer.\n",
- ((mips_hpt_frequency + 500) / 1000) / 1000,
- ((mips_hpt_frequency + 500) / 1000) % 1000);
+ if (mips_clockevent_init() || !cpu_has_mfc0_count_bug())
init_mips_clocksource();
- }
-
- mips_clockevent_init();
}
*/
if (v != l->value) {
printk(KERN_DEBUG "VPE loader: "
- "apply_r_mips_lo16/hi16: "
+ "apply_r_mips_lo16/hi16: \t"
"inconsistent value information\n");
return -ENOEXEC;
}
break;
case SHN_MIPS_SCOMMON:
- printk(KERN_DEBUG "simplify_symbols: ignoring SHN_MIPS_SCOMMON"
+ printk(KERN_DEBUG "simplify_symbols: ignoring SHN_MIPS_SCOMMON "
"symbol <%s> st_shndx %d\n", strtab + sym[i].st_name,
sym[i].st_shndx);
// .sbss section
ax.rv.si = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.si;
}
ax.rv.di = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.di;
}
ax.rv.dp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.dp;
}
ax.rv.dp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.dp;
}
ax.rv.sp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.sp;
}
ax.rv.sp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.sp;
}
void __init plat_time_init(void)
{
- unsigned int est_freq, flags;
-
- local_irq_save(flags);
+ unsigned int est_freq;
/* Set Data mode - binary. */
CMOS_WRITE(CMOS_READ(RTC_CONTROL) | RTC_DM_BINARY, RTC_CONTROL);
(est_freq % 1000000) * 100 / 1000000);
cpu_khz = est_freq / 1000;
-
- local_irq_restore(flags);
}
current_cpu_type() == CPU_R12000);
}
+static gfp_t massage_gfp_flags(const struct device *dev, gfp_t gfp)
+{
+ /* ignore region specifiers */
+ gfp &= ~(__GFP_DMA | __GFP_DMA32 | __GFP_HIGHMEM);
+
+#ifdef CONFIG_ZONE_DMA32
+ if (dev == NULL)
+ gfp |= __GFP_DMA;
+ else if (dev->coherent_dma_mask < DMA_BIT_MASK(24))
+ gfp |= __GFP_DMA;
+ else
+#endif
+#ifdef CONFIG_ZONE_DMA32
+ if (dev->coherent_dma_mask < DMA_BIT_MASK(32))
+ gfp |= __GFP_DMA32;
+ else
+#endif
+ ;
+
+ /* Don't invoke OOM killer */
+ gfp |= __GFP_NORETRY;
+
+ return gfp;
+}
+
void *dma_alloc_noncoherent(struct device *dev, size_t size,
dma_addr_t * dma_handle, gfp_t gfp)
{
void *ret;
- /* ignore region specifiers */
- gfp &= ~(__GFP_DMA | __GFP_HIGHMEM);
+ gfp = massage_gfp_flags(dev, gfp);
- if (dev == NULL || (dev->coherent_dma_mask < 0xffffffff))
- gfp |= GFP_DMA;
ret = (void *) __get_free_pages(gfp, get_order(size));
if (ret != NULL) {
{
void *ret;
- /* ignore region specifiers */
- gfp &= ~(__GFP_DMA | __GFP_HIGHMEM);
+ gfp = massage_gfp_flags(dev, gfp);
- if (dev == NULL || (dev->coherent_dma_mask < 0xffffffff))
- gfp |= GFP_DMA;
ret = (void *) __get_free_pages(gfp, get_order(size));
if (ret) {
* so we can't guarantee allocations that must be
* within a tighter range than GFP_DMA..
*/
- if (mask < 0x00ffffff)
+ if (mask < DMA_BIT_MASK(24))
return 0;
return 1;
void __init paging_init(void)
{
- unsigned long zones_size[MAX_NR_ZONES] = { 0, };
-#ifndef CONFIG_FLATMEM
- unsigned long zholes_size[MAX_NR_ZONES] = { 0, };
- unsigned long i, j, pfn;
-#endif
+ unsigned long max_zone_pfns[MAX_NR_ZONES];
+ unsigned long lastpfn;
pagetable_init();
kmap_coherent_init();
#ifdef CONFIG_ZONE_DMA
- if (min_low_pfn < MAX_DMA_PFN && MAX_DMA_PFN <= max_low_pfn) {
- zones_size[ZONE_DMA] = MAX_DMA_PFN - min_low_pfn;
- zones_size[ZONE_NORMAL] = max_low_pfn - MAX_DMA_PFN;
- } else if (max_low_pfn < MAX_DMA_PFN)
- zones_size[ZONE_DMA] = max_low_pfn - min_low_pfn;
- else
+ max_zone_pfns[ZONE_DMA] = MAX_DMA_PFN;
#endif
- zones_size[ZONE_NORMAL] = max_low_pfn - min_low_pfn;
-
+#ifdef CONFIG_ZONE_DMA32
+ max_zone_pfns[ZONE_DMA32] = MAX_DMA32_PFN;
+#endif
+ max_zone_pfns[ZONE_NORMAL] = max_low_pfn;
+ lastpfn = max_low_pfn;
#ifdef CONFIG_HIGHMEM
- zones_size[ZONE_HIGHMEM] = highend_pfn - highstart_pfn;
+ max_zone_pfns[ZONE_HIGHMEM] = highend_pfn;
+ lastpfn = highend_pfn;
- if (cpu_has_dc_aliases && zones_size[ZONE_HIGHMEM]) {
+ if (cpu_has_dc_aliases && max_low_pfn != highend_pfn) {
printk(KERN_WARNING "This processor doesn't support highmem."
- " %ldk highmem ignored\n", zones_size[ZONE_HIGHMEM]);
- zones_size[ZONE_HIGHMEM] = 0;
+ " %ldk highmem ignored\n",
+ (highend_pfn - max_low_pfn) << (PAGE_SHIFT - 10));
+ max_zone_pfns[ZONE_HIGHMEM] = max_low_pfn;
+ lastpfn = max_low_pfn;
}
#endif
-#ifdef CONFIG_FLATMEM
- free_area_init(zones_size);
-#else
- pfn = min_low_pfn;
- for (i = 0; i < MAX_NR_ZONES; i++)
- for (j = 0; j < zones_size[i]; j++, pfn++)
- if (!page_is_ram(pfn))
- zholes_size[i]++;
- free_area_init_node(0, NODE_DATA(0), zones_size, 0, zholes_size);
-#endif
+ free_area_init_nodes(max_zone_pfns);
}
static struct kcore_list kcore_mem, kcore_vmalloc;
config PMC_MSP4200_EVAL
bool "PMC-Sierra MSP4200 Eval Board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_MSP_SLP
select HW_HAS_PCI
config PMC_MSP4200_GW
bool "PMC-Sierra MSP4200 VoIP Gateway"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_MSP_SLP
select HW_HAS_PCI
#include <asm/sgi/ioc.h>
#include <asm/sgi/mc.h>
#include <asm/sgi/ip22.h>
+#include <asm/i8259.h>
/* I2 has four EISA slots. */
#define IP22_EISA_MAX_SLOTS 4
return IRQ_NONE;
}
-static void enable_eisa1_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT1_MASK);
- mask &= ~((u8) (1 << irq));
- outb(mask, EISA_INT1_MASK);
-}
-
-static unsigned int startup_eisa1_irq(unsigned int irq)
-{
- u8 edge;
-
- /* Only use edge interrupts for EISA */
-
- edge = inb(EISA_INT1_EDGE_LEVEL);
- edge &= ~((u8) (1 << irq));
- outb(edge, EISA_INT1_EDGE_LEVEL);
-
- enable_eisa1_irq(irq);
- return 0;
-}
-
-static void disable_eisa1_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT1_MASK);
- mask |= ((u8) (1 << irq));
- outb(mask, EISA_INT1_MASK);
-}
-
-static void mask_and_ack_eisa1_irq(unsigned int irq)
-{
- disable_eisa1_irq(irq);
-
- outb(0x20, EISA_INT1_CTRL);
-}
-
-static void end_eisa1_irq(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- enable_eisa1_irq(irq);
-}
-
-static struct irq_chip ip22_eisa1_irq_type = {
- .name = "IP22 EISA",
- .startup = startup_eisa1_irq,
- .ack = mask_and_ack_eisa1_irq,
- .mask = disable_eisa1_irq,
- .mask_ack = mask_and_ack_eisa1_irq,
- .unmask = enable_eisa1_irq,
- .end = end_eisa1_irq,
-};
-
-static void enable_eisa2_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT2_MASK);
- mask &= ~((u8) (1 << (irq - 8)));
- outb(mask, EISA_INT2_MASK);
-}
-
-static unsigned int startup_eisa2_irq(unsigned int irq)
-{
- u8 edge;
-
- /* Only use edge interrupts for EISA */
-
- edge = inb(EISA_INT2_EDGE_LEVEL);
- edge &= ~((u8) (1 << (irq - 8)));
- outb(edge, EISA_INT2_EDGE_LEVEL);
-
- enable_eisa2_irq(irq);
- return 0;
-}
-
-static void disable_eisa2_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT2_MASK);
- mask |= ((u8) (1 << (irq - 8)));
- outb(mask, EISA_INT2_MASK);
-}
-
-static void mask_and_ack_eisa2_irq(unsigned int irq)
-{
- disable_eisa2_irq(irq);
-
- outb(0x20, EISA_INT2_CTRL);
-}
-
-static void end_eisa2_irq(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- enable_eisa2_irq(irq);
-}
-
-static struct irq_chip ip22_eisa2_irq_type = {
- .name = "IP22 EISA",
- .startup = startup_eisa2_irq,
- .ack = mask_and_ack_eisa2_irq,
- .mask = disable_eisa2_irq,
- .mask_ack = mask_and_ack_eisa2_irq,
- .unmask = enable_eisa2_irq,
- .end = end_eisa2_irq,
-};
-
static struct irqaction eisa_action = {
.handler = ip22_eisa_intr,
.name = "EISA",
};
-static struct irqaction cascade_action = {
- .handler = no_action,
- .name = "EISA cascade",
-};
-
int __init ip22_eisa_init(void)
{
int i, c;
outb(1, EISA_EXT_NMI_RESET_CTRL);
udelay(50); /* Wait long enough for the dust to settle */
outb(0, EISA_EXT_NMI_RESET_CTRL);
- outb(0x11, EISA_INT1_CTRL);
- outb(0x11, EISA_INT2_CTRL);
- outb(0, EISA_INT1_MASK);
- outb(8, EISA_INT2_MASK);
- outb(4, EISA_INT1_MASK);
- outb(2, EISA_INT2_MASK);
- outb(1, EISA_INT1_MASK);
- outb(1, EISA_INT2_MASK);
- outb(0xfb, EISA_INT1_MASK);
- outb(0xff, EISA_INT2_MASK);
outb(0, EISA_DMA2_WRITE_SINGLE);
- for (i = SGINT_EISA; i < (SGINT_EISA + EISA_MAX_IRQ); i++) {
- if (i < (SGINT_EISA + 8))
- set_irq_chip(i, &ip22_eisa1_irq_type);
- else
- set_irq_chip(i, &ip22_eisa2_irq_type);
- }
+ init_i8259_irqs();
/* Cannot use request_irq because of kmalloc not being ready at such
* an early stage. Yes, I've been bitten... */
setup_irq(SGI_EISA_IRQ, &eisa_action);
- setup_irq(SGINT_EISA + 2, &cascade_action);
EISA_bus = 1;
return 0;
for (x=0; x<100000; x++) __asm__ __volatile__(""); })
#define eeprom_cs_on(ptr) ({ \
- *ptr &= ~EEPROM_DATO; \
- *ptr &= ~EEPROM_ECLK; \
- *ptr &= ~EEPROM_EPROT; \
- delay(); \
- *ptr |= EEPROM_CSEL; \
- *ptr |= EEPROM_ECLK; })
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_DATO, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_EPROT, ptr); \
+ delay(); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_CSEL, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
#define eeprom_cs_off(ptr) ({ \
- *ptr &= ~EEPROM_ECLK; \
- *ptr &= ~EEPROM_CSEL; \
- *ptr |= EEPROM_EPROT; \
- *ptr |= EEPROM_ECLK; })
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_CSEL, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_EPROT, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
#define BITS_IN_COMMAND 11
/*
ser_cmd = cmd | (reg << (16 - BITS_IN_COMMAND));
for (i = 0; i < BITS_IN_COMMAND; i++) {
if (ser_cmd & (1<<15)) /* if high order bit set */
- writel(readl(ctrl) | EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) | EEPROM_DATO, ctrl);
else
- writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
- writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
- writel(readl(ctrl) | EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
+ delay();
+ __raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
+ delay();
ser_cmd <<= 1;
}
/* see data sheet timing diagram */
- writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
}
unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg)
unsigned short res = 0;
int i;
- writel(readl(ctrl) & ~EEPROM_EPROT, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_EPROT, ctrl);
eeprom_cs_on(ctrl);
eeprom_cmd(ctrl, EEPROM_READ, reg);
/* clock the data ouf of serial mem */
for (i = 0; i < 16; i++) {
- writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
delay();
- writel(readl(ctrl) | EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
delay();
res <<= 1;
- if (readl(ctrl) & EEPROM_DATI)
+ if (__raw_readl(ctrl) & EEPROM_DATI)
res |= 1;
}
static void enable_macepci_irq(unsigned int irq)
{
- macepci_mask |= MACEPCI_CONTROL_INT(irq - 9);
+ macepci_mask |= MACEPCI_CONTROL_INT(irq - MACEPCI_SCSI0_IRQ);
mace->pci.control = macepci_mask;
- crime_mask |= 1 << (irq - 1);
+ crime_mask |= 1 << (irq - CRIME_IRQ_BASE);
crime->imask = crime_mask;
}
static void disable_macepci_irq(unsigned int irq)
{
- crime_mask &= ~(1 << (irq - 1));
+ crime_mask &= ~(1 << (irq - CRIME_IRQ_BASE));
crime->imask = crime_mask;
flush_crime_bus();
- macepci_mask &= ~MACEPCI_CONTROL_INT(irq - 9);
+ macepci_mask &= ~MACEPCI_CONTROL_INT(irq - MACEPCI_SCSI0_IRQ);
mace->pci.control = macepci_mask;
flush_mace_bus();
}
pr_debug("crime_int %08x enabled\n", crime_int);
crime_mask |= crime_int;
crime->imask = crime_mask;
- maceisa_mask |= 1 << (irq - 33);
+ maceisa_mask |= 1 << (irq - MACEISA_AUDIO_SW_IRQ);
mace->perif.ctrl.imask = maceisa_mask;
}
{
unsigned int crime_int = 0;
- maceisa_mask &= ~(1 << (irq - 33));
+ maceisa_mask &= ~(1 << (irq - MACEISA_AUDIO_SW_IRQ));
if (!(maceisa_mask & MACEISA_AUDIO_INT))
crime_int |= MACE_AUDIO_INT;
if (!(maceisa_mask & MACEISA_MISC_INT))
case MACEISA_SERIAL2_TDMAPR_IRQ:
/* edge triggered */
mace_int = mace->perif.ctrl.istat;
- mace_int &= ~(1 << (irq - 33));
+ mace_int &= ~(1 << (irq - MACEISA_AUDIO_SW_IRQ));
mace->perif.ctrl.istat = mace_int;
break;
}
static void enable_mace_irq(unsigned int irq)
{
- crime_mask |= 1 << (irq - 1);
+ unsigned int bit = irq - CRIME_IRQ_BASE;
+
+ crime_mask |= (1 << bit);
crime->imask = crime_mask;
}
static void disable_mace_irq(unsigned int irq)
{
- crime_mask &= ~(1 << (irq - 1));
+ unsigned int bit = irq - CRIME_IRQ_BASE;
+
+ crime_mask &= ~(1 << bit);
crime->imask = crime_mask;
flush_crime_bus();
}
mace->perif.ctrl.imask = 0;
mips_cpu_irq_init();
- for (irq = MIPS_CPU_IRQ_BASE + 8; irq <= IP32_IRQ_MAX; irq++) {
+ for (irq = CRIME_IRQ_BASE; irq <= IP32_IRQ_MAX; irq++) {
switch (irq) {
case MACE_VID_IN1_IRQ ... MACE_PCI_BRIDGE_IRQ:
set_irq_chip(irq, &ip32_mace_interrupt);
config CASIO_E55
bool "CASIO CASSIOPEIA E-10/15/55/65"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select ISA
config IBM_WORKPAD
bool "IBM WorkPad z50"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select ISA
config NEC_CMBVR4133
bool "NEC CMB-VR4133"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config TANBAC_TB022X
bool "TANBAC VR4131 multichip module and TANBAC VR4131DIMM"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config VICTOR_MPC30X
bool "Victor MP-C303/304"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config ZAO_CAPCELLA
bool "ZAO Networks Capcella"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
serial@4500 {
reg = <700 100>;
device_type = "ipic";
};
-
+
par_io@1400 {
reg = <1400 100>;
device_type = "par_io";
3 5 1 0 2 0 /* MDC */
0 d 2 0 1 0 /* RX_CLK (CLK9) */
3 18 2 0 1 0 /* TX_CLK (CLK10) */
- 1 1 1 0 1 0 /* TxD1 */
1 0 1 0 1 0 /* TxD0 */
1 1 1 0 1 0 /* TxD1 */
1 2 1 0 1 0 /* TxD2 */
reg = <e0100000 480>;
brg-frequency = <0>;
bus-frequency = <BCD3D80>;
-
+
muram@10000 {
device_type = "muram";
ranges = <0 00010000 00004000>;
-
+
data-only@0 {
reg = <0 4000>;
};
compatible = "ucc_geth";
model = "UCC";
device-id = <4>;
- reg = <3000 200>;
+ reg = <3200 200>;
interrupts = <23>;
interrupt-parent = < &qeic >;
/*
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1b 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 1>;
interrupt-map = <
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
pcie@0 {
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 7>;
interrupt-map = <
- /* IDSEL 0x11 - PCI slot 1 */
+ /* IDSEL 0x11 func 0 - PCI slot 1 */
8800 0 0 1 &mpic 2 1
8800 0 0 2 &mpic 3 1
8800 0 0 3 &mpic 4 1
8800 0 0 4 &mpic 1 1
- /* IDSEL 0x12 - PCI slot 2 */
+ /* IDSEL 0x11 func 1 - PCI slot 1 */
+ 8900 0 0 1 &mpic 2 1
+ 8900 0 0 2 &mpic 3 1
+ 8900 0 0 3 &mpic 4 1
+ 8900 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 2 - PCI slot 1 */
+ 8a00 0 0 1 &mpic 2 1
+ 8a00 0 0 2 &mpic 3 1
+ 8a00 0 0 3 &mpic 4 1
+ 8a00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 3 - PCI slot 1 */
+ 8b00 0 0 1 &mpic 2 1
+ 8b00 0 0 2 &mpic 3 1
+ 8b00 0 0 3 &mpic 4 1
+ 8b00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 4 - PCI slot 1 */
+ 8c00 0 0 1 &mpic 2 1
+ 8c00 0 0 2 &mpic 3 1
+ 8c00 0 0 3 &mpic 4 1
+ 8c00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 5 - PCI slot 1 */
+ 8d00 0 0 1 &mpic 2 1
+ 8d00 0 0 2 &mpic 3 1
+ 8d00 0 0 3 &mpic 4 1
+ 8d00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 6 - PCI slot 1 */
+ 8e00 0 0 1 &mpic 2 1
+ 8e00 0 0 2 &mpic 3 1
+ 8e00 0 0 3 &mpic 4 1
+ 8e00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 7 - PCI slot 1 */
+ 8f00 0 0 1 &mpic 2 1
+ 8f00 0 0 2 &mpic 3 1
+ 8f00 0 0 3 &mpic 4 1
+ 8f00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 func 0 - PCI slot 2 */
9000 0 0 1 &mpic 3 1
9000 0 0 2 &mpic 4 1
9000 0 0 3 &mpic 1 1
9000 0 0 4 &mpic 2 1
+ /* IDSEL 0x12 func 1 - PCI slot 2 */
+ 9100 0 0 1 &mpic 3 1
+ 9100 0 0 2 &mpic 4 1
+ 9100 0 0 3 &mpic 1 1
+ 9100 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 2 - PCI slot 2 */
+ 9200 0 0 1 &mpic 3 1
+ 9200 0 0 2 &mpic 4 1
+ 9200 0 0 3 &mpic 1 1
+ 9200 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 3 - PCI slot 2 */
+ 9300 0 0 1 &mpic 3 1
+ 9300 0 0 2 &mpic 4 1
+ 9300 0 0 3 &mpic 1 1
+ 9300 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 4 - PCI slot 2 */
+ 9400 0 0 1 &mpic 3 1
+ 9400 0 0 2 &mpic 4 1
+ 9400 0 0 3 &mpic 1 1
+ 9400 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 5 - PCI slot 2 */
+ 9500 0 0 1 &mpic 3 1
+ 9500 0 0 2 &mpic 4 1
+ 9500 0 0 3 &mpic 1 1
+ 9500 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 6 - PCI slot 2 */
+ 9600 0 0 1 &mpic 3 1
+ 9600 0 0 2 &mpic 4 1
+ 9600 0 0 3 &mpic 1 1
+ 9600 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 7 - PCI slot 2 */
+ 9700 0 0 1 &mpic 3 1
+ 9700 0 0 2 &mpic 4 1
+ 9700 0 0 3 &mpic 1 1
+ 9700 0 0 4 &mpic 2 1
+
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 7>;
interrupt-map = <
- /* IDSEL 0x11 */
- 8800 0 0 1 &i8259 9 2
- 8800 0 0 2 &i8259 a 2
- 8800 0 0 3 &i8259 b 2
- 8800 0 0 4 &i8259 c 2
-
- /* IDSEL 0x12 */
- 9000 0 0 1 &i8259 a 2
- 9000 0 0 2 &i8259 b 2
- 9000 0 0 3 &i8259 c 2
- 9000 0 0 4 &i8259 9 2
+ /* IDSEL 0x11 func 0 - PCI slot 1 */
+ 8800 0 0 1 &mpic 2 1
+ 8800 0 0 2 &mpic 3 1
+ 8800 0 0 3 &mpic 4 1
+ 8800 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 1 - PCI slot 1 */
+ 8900 0 0 1 &mpic 2 1
+ 8900 0 0 2 &mpic 3 1
+ 8900 0 0 3 &mpic 4 1
+ 8900 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 2 - PCI slot 1 */
+ 8a00 0 0 1 &mpic 2 1
+ 8a00 0 0 2 &mpic 3 1
+ 8a00 0 0 3 &mpic 4 1
+ 8a00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 3 - PCI slot 1 */
+ 8b00 0 0 1 &mpic 2 1
+ 8b00 0 0 2 &mpic 3 1
+ 8b00 0 0 3 &mpic 4 1
+ 8b00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 4 - PCI slot 1 */
+ 8c00 0 0 1 &mpic 2 1
+ 8c00 0 0 2 &mpic 3 1
+ 8c00 0 0 3 &mpic 4 1
+ 8c00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 5 - PCI slot 1 */
+ 8d00 0 0 1 &mpic 2 1
+ 8d00 0 0 2 &mpic 3 1
+ 8d00 0 0 3 &mpic 4 1
+ 8d00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 6 - PCI slot 1 */
+ 8e00 0 0 1 &mpic 2 1
+ 8e00 0 0 2 &mpic 3 1
+ 8e00 0 0 3 &mpic 4 1
+ 8e00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 7 - PCI slot 1 */
+ 8f00 0 0 1 &mpic 2 1
+ 8f00 0 0 2 &mpic 3 1
+ 8f00 0 0 3 &mpic 4 1
+ 8f00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 func 0 - PCI slot 2 */
+ 9000 0 0 1 &mpic 3 1
+ 9000 0 0 2 &mpic 4 1
+ 9000 0 0 3 &mpic 1 1
+ 9000 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 1 - PCI slot 2 */
+ 9100 0 0 1 &mpic 3 1
+ 9100 0 0 2 &mpic 4 1
+ 9100 0 0 3 &mpic 1 1
+ 9100 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 2 - PCI slot 2 */
+ 9200 0 0 1 &mpic 3 1
+ 9200 0 0 2 &mpic 4 1
+ 9200 0 0 3 &mpic 1 1
+ 9200 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 3 - PCI slot 2 */
+ 9300 0 0 1 &mpic 3 1
+ 9300 0 0 2 &mpic 4 1
+ 9300 0 0 3 &mpic 1 1
+ 9300 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 4 - PCI slot 2 */
+ 9400 0 0 1 &mpic 3 1
+ 9400 0 0 2 &mpic 4 1
+ 9400 0 0 3 &mpic 1 1
+ 9400 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 5 - PCI slot 2 */
+ 9500 0 0 1 &mpic 3 1
+ 9500 0 0 2 &mpic 4 1
+ 9500 0 0 3 &mpic 1 1
+ 9500 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 6 - PCI slot 2 */
+ 9600 0 0 1 &mpic 3 1
+ 9600 0 0 2 &mpic 4 1
+ 9600 0 0 3 &mpic 1 1
+ 9600 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 7 - PCI slot 2 */
+ 9700 0 0 1 &mpic 3 1
+ 9700 0 0 2 &mpic 4 1
+ 9700 0 0 3 &mpic 1 1
+ 9700 0 0 4 &mpic 2 1
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
pcie@0 {
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
#
# SPI support
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_MPC83xx=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+
+#
+# MMC/SD Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_WBSD is not set
+# CONFIG_MMC_TIFM_SD is not set
+CONFIG_MMC_SPI=y
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
+CONFIG_CRC7=y
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_USB_EHCI_FSL=y
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
-# CONFIG_USB_UHCI_HCD is not set
+CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_SPLIT_ISO is not set
CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
CONFIG_USB_EHCI_FSL=y
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+CONFIG_USB_UHCI_HCD=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+
+#
+# USB DSL modem support
+#
+
#
# USB Gadget Support
#
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
DEFINE(CFG_SYSCALL_MAP32, offsetof(struct vdso_data, syscall_map_32));
DEFINE(WTOM_CLOCK_SEC, offsetof(struct vdso_data, wtom_clock_sec));
DEFINE(WTOM_CLOCK_NSEC, offsetof(struct vdso_data, wtom_clock_nsec));
+ DEFINE(CFG_ICACHE_BLOCKSZ, offsetof(struct vdso_data, icache_block_size));
+ DEFINE(CFG_DCACHE_BLOCKSZ, offsetof(struct vdso_data, dcache_block_size));
+ DEFINE(CFG_ICACHE_LOGBLOCKSZ, offsetof(struct vdso_data, icache_log_block_size));
+ DEFINE(CFG_DCACHE_LOGBLOCKSZ, offsetof(struct vdso_data, dcache_log_block_size));
#ifdef CONFIG_PPC64
DEFINE(CFG_SYSCALL_MAP64, offsetof(struct vdso_data, syscall_map_64));
DEFINE(TVAL64_TV_SEC, offsetof(struct timeval, tv_sec));
#include <linux/init.h>
#include <linux/capability.h>
#include <linux/delay.h>
+#include <linux/smp.h>
+#include <linux/completion.h>
+#include <linux/cpumask.h>
#include <asm/prom.h>
#include <asm/rtas.h>
#include <asm/lmb.h>
#include <asm/udbg.h>
#include <asm/syscalls.h>
+#include <asm/smp.h>
+#include <asm/atomic.h>
struct rtas_t rtas = {
.lock = SPIN_LOCK_UNLOCKED
EXPORT_SYMBOL(rtas);
struct rtas_suspend_me_data {
- long waiting;
- struct rtas_args *args;
+ atomic_t working; /* number of cpus accessing this struct */
+ int token; /* ibm,suspend-me */
+ int error;
+ struct completion *complete; /* wait on this until working == 0 */
};
DEFINE_SPINLOCK(rtas_data_buf_lock);
/* Must be in the RMO region, so we place it here */
static char rtas_os_term_buf[2048];
-void rtas_os_term(char *str)
+void rtas_panic_msg(char *str)
{
- int status;
+ snprintf(rtas_os_term_buf, 2048, "OS panic: %s", str);
+}
- if (panic_timeout)
- return;
+void rtas_os_term(void)
+{
+ int status;
if (RTAS_UNKNOWN_SERVICE == rtas_token("ibm,os-term"))
return;
- snprintf(rtas_os_term_buf, 2048, "OS panic: %s", str);
-
do {
status = rtas_call(rtas_token("ibm,os-term"), 1, 1, NULL,
__pa(rtas_os_term_buf));
#ifdef CONFIG_PPC_PSERIES
static void rtas_percpu_suspend_me(void *info)
{
- int i;
long rc;
- long flags;
+ unsigned long msr_save;
+ int cpu;
struct rtas_suspend_me_data *data =
(struct rtas_suspend_me_data *)info;
- /*
- * We use "waiting" to indicate our state. As long
- * as it is >0, we are still trying to all join up.
- * If it goes to 0, we have successfully joined up and
- * one thread got H_CONTINUE. If any error happens,
- * we set it to <0.
- */
- local_irq_save(flags);
- do {
- rc = plpar_hcall_norets(H_JOIN);
- smp_rmb();
- } while (rc == H_SUCCESS && data->waiting > 0);
- if (rc == H_SUCCESS)
- goto out;
+ atomic_inc(&data->working);
+
+ /* really need to ensure MSR.EE is off for H_JOIN */
+ msr_save = mfmsr();
+ mtmsr(msr_save & ~(MSR_EE));
+
+ rc = plpar_hcall_norets(H_JOIN);
- if (rc == H_CONTINUE) {
- data->waiting = 0;
- data->args->args[data->args->nargs] =
- rtas_call(ibm_suspend_me_token, 0, 1, NULL);
- for_each_possible_cpu(i)
- plpar_hcall_norets(H_PROD,i);
+ mtmsr(msr_save);
+
+ if (rc == H_SUCCESS) {
+ /* This cpu was prodded and the suspend is complete. */
+ goto out;
+ } else if (rc == H_CONTINUE) {
+ /* All other cpus are in H_JOIN, this cpu does
+ * the suspend.
+ */
+ printk(KERN_DEBUG "calling ibm,suspend-me on cpu %i\n",
+ smp_processor_id());
+ data->error = rtas_call(data->token, 0, 1, NULL);
+
+ if (data->error)
+ printk(KERN_DEBUG "ibm,suspend-me returned %d\n",
+ data->error);
} else {
- data->waiting = -EBUSY;
- printk(KERN_ERR "Error on H_JOIN hypervisor call\n");
+ printk(KERN_ERR "H_JOIN on cpu %i failed with rc = %ld\n",
+ smp_processor_id(), rc);
+ data->error = rc;
}
-
+ /* This cpu did the suspend or got an error; in either case,
+ * we need to prod all other other cpus out of join state.
+ * Extra prods are harmless.
+ */
+ for_each_online_cpu(cpu)
+ plpar_hcall_norets(H_PROD, get_hard_smp_processor_id(cpu));
out:
- local_irq_restore(flags);
- return;
+ if (atomic_dec_return(&data->working) == 0)
+ complete(data->complete);
}
static int rtas_ibm_suspend_me(struct rtas_args *args)
{
- int i;
long state;
long rc;
unsigned long retbuf[PLPAR_HCALL_BUFSIZE];
struct rtas_suspend_me_data data;
+ DECLARE_COMPLETION_ONSTACK(done);
+
+ if (!rtas_service_present("ibm,suspend-me"))
+ return -ENOSYS;
/* Make sure the state is valid */
rc = plpar_hcall(H_VASI_STATE, retbuf,
return 0;
}
- data.waiting = 1;
- data.args = args;
+ atomic_set(&data.working, 0);
+ data.token = rtas_token("ibm,suspend-me");
+ data.error = 0;
+ data.complete = &done;
/* Call function on all CPUs. One of us will make the
* rtas call
*/
if (on_each_cpu(rtas_percpu_suspend_me, &data, 1, 0))
- data.waiting = -EINVAL;
+ data.error = -EINVAL;
- if (data.waiting != 0)
- printk(KERN_ERR "Error doing global join\n");
+ wait_for_completion(&done);
- /* Prod each CPU. This won't hurt, and will wake
- * anyone we successfully put to sleep with H_JOIN.
- */
- for_each_possible_cpu(i)
- plpar_hcall_norets(H_PROD, i);
+ if (data.error != 0)
+ printk(KERN_ERR "Error doing global join\n");
- return data.waiting;
+ return data.error;
}
#else /* CONFIG_PPC_PSERIES */
static int rtas_ibm_suspend_me(struct rtas_args *args)
/* deltascaled includes both user and system time.
* Hence scale it based on the purr ratio to estimate
* the system time */
- deltascaled = deltascaled * get_paca()->system_time /
- (get_paca()->system_time + get_paca()->user_time);
+ if (get_paca()->user_time)
+ deltascaled = deltascaled * get_paca()->system_time /
+ (get_paca()->system_time + get_paca()->user_time);
delta += get_paca()->system_time;
get_paca()->system_time = 0;
}
vdso_data->icache_size = ppc64_caches.isize;
vdso_data->icache_line_size = ppc64_caches.iline_size;
+ /* XXXOJN: Blocks should be added to ppc64_caches and used instead */
+ vdso_data->dcache_block_size = ppc64_caches.dline_size;
+ vdso_data->icache_block_size = ppc64_caches.iline_size;
+ vdso_data->dcache_log_block_size = ppc64_caches.log_dline_size;
+ vdso_data->icache_log_block_size = ppc64_caches.log_iline_size;
+
/*
* Calculate the size of the 64 bits vDSO
*/
vdso64_pages = (&vdso64_end - &vdso64_start) >> PAGE_SHIFT;
DBG("vdso64_kbase: %p, 0x%x pages\n", vdso64_kbase, vdso64_pages);
+#else
+ vdso_data->dcache_block_size = L1_CACHE_BYTES;
+ vdso_data->dcache_log_block_size = L1_CACHE_SHIFT;
+ vdso_data->icache_block_size = L1_CACHE_BYTES;
+ vdso_data->icache_log_block_size = L1_CACHE_SHIFT;
#endif /* CONFIG_PPC64 */
*
* Flushes the data cache & invalidate the instruction cache for the
* provided range [start, end[
- *
- * Note: all CPUs supported by this kernel have a 128 bytes cache
- * line size so we don't have to peek that info from the datapage
*/
V_FUNCTION_BEGIN(__kernel_sync_dicache)
.cfi_startproc
- li r5,127
- andc r6,r3,r5 /* round low to line bdy */
+ mflr r12
+ .cfi_register lr,r12
+ mr r11,r3
+ bl __get_datapage@local
+ mtlr r12
+ mr r10,r3
+
+ lwz r7,CFG_DCACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
subf r8,r6,r4 /* compute length */
add r8,r8,r5 /* ensure we get enough */
- srwi. r8,r8,7 /* compute line count */
+ lwz r9,CFG_DCACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
crclr cr0*4+so
beqlr /* nothing to do? */
mtctr r8
- mr r3,r6
-1: dcbst 0,r3
- addi r3,r3,128
+1: dcbst 0,r6
+ add r6,r6,r7
bdnz 1b
sync
+
+/* Now invalidate the instruction cache */
+
+ lwz r7,CFG_ICACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
+ subf r8,r6,r4 /* compute length */
+ add r8,r8,r5
+ lwz r9,CFG_ICACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
+ crclr cr0*4+so
+ beqlr /* nothing to do? */
mtctr r8
-1: icbi 0,r6
- addi r6,r6,128
- bdnz 1b
+2: icbi 0,r6
+ add r6,r6,r7
+ bdnz 2b
isync
li r3,0
blr
*
* Flushes the data cache & invalidate the instruction cache for the
* provided range [start, end[
- *
- * Note: all CPUs supported by this kernel have a 128 bytes cache
- * line size so we don't have to peek that info from the datapage
*/
V_FUNCTION_BEGIN(__kernel_sync_dicache)
.cfi_startproc
- li r5,127
- andc r6,r3,r5 /* round low to line bdy */
+ mflr r12
+ .cfi_register lr,r12
+ mr r11,r3
+ bl V_LOCAL_FUNC(__get_datapage)
+ mtlr r12
+ mr r10,r3
+
+ lwz r7,CFG_DCACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
subf r8,r6,r4 /* compute length */
add r8,r8,r5 /* ensure we get enough */
- srwi. r8,r8,7 /* compute line count */
+ lwz r9,CFG_DCACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
crclr cr0*4+so
beqlr /* nothing to do? */
mtctr r8
- mr r3,r6
-1: dcbst 0,r3
- addi r3,r3,128
+1: dcbst 0,r6
+ add r6,r6,r7
bdnz 1b
sync
+
+/* Now invalidate the instruction cache */
+
+ lwz r7,CFG_ICACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
+ subf r8,r6,r4 /* compute length */
+ add r8,r8,r5
+ lwz r9,CFG_ICACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
+ crclr cr0*4+so
+ beqlr /* nothing to do? */
mtctr r8
-1: icbi 0,r6
- addi r6,r6,128
- bdnz 1b
+2: icbi 0,r6
+ add r6,r6,r7
+ bdnz 2b
isync
li r3,0
blr
* we invalidate the TLB here, thus avoiding dcbst
* misbehaviour.
*/
- _tlbie(address);
+ _tlbie(address, 0 /* 8xx doesn't care about PID */);
#endif
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
* architectures. -- Dan
*/
#if defined(CONFIG_8xx)
-#define flush_HPTE(X, va, pg) _tlbie(va)
+#define flush_HPTE(X, va, pg) _tlbie(va, 0 /* 8xx doesn't care about PID */)
#define MMU_init_hw() do { } while(0)
#define mmu_mapin_ram() (0UL)
#include <asm/lmb.h>
#include <asm/abs_addr.h>
#include <asm/firmware.h>
+#include <asm/iseries/hv_call.h>
struct stab_entry {
unsigned long esid_data;
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
static struct of_device_id walnut_of_bus[] = {
{ .compatible = "ibm,plb3", },
* option) any later version.
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
static struct of_device_id bamboo_of_bus[] = {
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
* option) any later version.
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
static struct of_device_id sequoia_of_bus[] = {
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
!= NULL){
- /* Reset the Ethernet PHY */
- bcsr_regs[9] &= ~0x20;
+ /* Reset the Ethernet PHYs */
+#define BCSR8_FETH_RST 0x50
+ bcsr_regs[8] &= ~BCSR8_FETH_RST;
udelay(1000);
- bcsr_regs[9] |= 0x20;
+ bcsr_regs[8] |= BCSR8_FETH_RST;
iounmap(bcsr_regs);
of_node_put(np);
}
#endif /* CONFIG_QUICC_ENGINE */
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc832x_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc832x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc832x_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
*/
#include <linux/pci.h>
+#include <linux/interrupt.h>
#include <linux/spi/spi.h>
+#include <linux/spi/mmc_spi.h>
+#include <linux/mmc/host.h>
#include <asm/of_platform.h>
#include <asm/time.h>
par_io_data_set(3, 13, !polarity);
}
+static struct mmc_spi_platform_data mpc832x_mmc_pdata = {
+ .ocr_mask = MMC_VDD_33_34,
+};
+
static struct spi_board_info mpc832x_spi_boardinfo = {
.bus_num = 0x4c0,
.chip_select = 0,
.max_speed_hz = 50000000,
- /*
- * XXX: This is spidev (spi in userspace) stub, should
- * be replaced by "mmc_spi" when mmc_spi will hit mainline.
- */
- .modalias = "spidev",
+ .modalias = "mmc_spi",
+ .platform_data = &mpc832x_mmc_pdata,
};
static int __init mpc832x_spi_init(void)
ipic_set_default_priority();
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc834x_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc834x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc834x_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
!= NULL){
+ uint svid;
+
/* Reset the Ethernet PHY */
- bcsr_regs[9] &= ~0x20;
+#define BCSR9_GETHRST 0x20
+ clrbits8(&bcsr_regs[9], BCSR9_GETHRST);
udelay(1000);
- bcsr_regs[9] |= 0x20;
+ setbits8(&bcsr_regs[9], BCSR9_GETHRST);
+
+ /* handle mpc8360ea rev.2.1 erratum 2: RGMII Timing */
+ svid = mfspr(SPRN_SVR);
+ if (svid == 0x80480021) {
+ void __iomem *immap;
+
+ immap = ioremap(get_immrbase() + 0x14a8, 8);
+
+ /*
+ * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
+ * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
+ */
+ setbits32(immap, 0x0c003000);
+
+ /*
+ * IMMR + 0x14AC[20:27] = 10101010
+ * (data delay for both UCC's)
+ */
+ clrsetbits_be32(immap + 4, 0xff0, 0xaa0);
+
+ iounmap(immap);
+ }
+
iounmap(bcsr_regs);
of_node_put(np);
}
-
#endif /* CONFIG_QUICC_ENGINE */
}
#endif /* CONFIG_QUICC_ENGINE */
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc8360_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc836x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc8360_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
out_be32(immap + MPC83XX_SCCR_OFFS, temp);
/* Configure pin mux for ULPI. There is no pin mux for UTMI */
- if (!strcmp(prop, "ulpi")) {
+ if (prop && !strcmp(prop, "ulpi")) {
temp = in_be32(immap + MPC83XX_SICRL_OFFS);
temp &= ~MPC831X_SICRL_USB_MASK;
temp |= MPC831X_SICRL_USB_ULPI;
usb_regs = ioremap(res.start, res.end - res.start + 1);
/* Using on-chip PHY */
- if (!strcmp(prop, "utmi_wide") ||
- !strcmp(prop, "utmi")) {
+ if (prop && (!strcmp(prop, "utmi_wide") ||
+ !strcmp(prop, "utmi"))) {
/* Set UTMI_PHY_EN, REFSEL to 48MHZ */
out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
CONTROL_UTMI_PHY_EN | CONTROL_REFSEL_48MHZ);
/* Using external UPLI PHY */
- } else if (!strcmp(prop, "ulpi")) {
+ } else if (prop && !strcmp(prop, "ulpi")) {
/* Set PHY_CLK_SEL to ULPI */
temp = CONTROL_PHY_CLK_SEL_ULPI;
#ifdef CONFIG_USB_OTG
{
/* remove all entries */
spufs_prune_dir(dir);
+ d_drop(dir);
return simple_rmdir(parent, dir);
}
strncpy(prpmc2800_platform_name, m,
min((int)len, PLATFORM_NAME_MAX - 1));
+ _set_L2CR(_get_L2CR() | L2CR_L2E);
return 1;
}
printk(KERN_DEBUG "OpenPIC addr: %lx\n", openpic_addr);
mpic = mpic_alloc(mpic_node, openpic_addr,
- MPIC_PRIMARY|MPIC_LARGE_VECTORS|MPIC_WANTS_RESET,
+ MPIC_PRIMARY|MPIC_LARGE_VECTORS,
0, 0, " PAS-OPIC ");
BUG_ON(!mpic);
config EEH
bool "PCI Extended Error Handling (EEH)" if EMBEDDED
- depends on PPC_PSERIES
+ depends on PPC_PSERIES && PCI
default y if !EMBEDDED
config SCANLOG
.restart = rtas_restart,
.power_off = pSeries_power_off,
.halt = rtas_halt,
- .panic = rtas_os_term,
+ .panic = rtas_panic_msg,
+ .machine_shutdown = rtas_os_term,
.get_boot_time = rtas_get_boot_time,
.get_rtc_time = rtas_get_rtc_time,
.set_rtc_time = rtas_set_rtc_time,
spin_unlock_irqrestore(&uic->lock, flags);
}
+static void uic_mask_ack_irq(unsigned int virq)
+{
+ struct uic *uic = get_irq_chip_data(virq);
+ unsigned int src = uic_irq_to_hw(virq);
+ unsigned long flags;
+ u32 er, sr;
+
+ sr = 1 << (31-src);
+ spin_lock_irqsave(&uic->lock, flags);
+ er = mfdcr(uic->dcrbase + UIC_ER);
+ er &= ~sr;
+ mtdcr(uic->dcrbase + UIC_ER, er);
+ mtdcr(uic->dcrbase + UIC_SR, sr);
+ spin_unlock_irqrestore(&uic->lock, flags);
+}
+
static int uic_set_irq_type(unsigned int virq, unsigned int flow_type)
{
struct uic *uic = get_irq_chip_data(virq);
.typename = " UIC ",
.unmask = uic_unmask_irq,
.mask = uic_mask_irq,
-/* .mask_ack = uic_mask_irq_and_ack, */
+ .mask_ack = uic_mask_ack_irq,
.ack = uic_ack_irq,
.set_type = uic_set_irq_type,
};
* Identify the CPU type and fix up code sections
* that depend on which cpu we have.
*/
+#if defined(CONFIG_440EP) && defined(CONFIG_PPC_FPU)
+ /* We pass the virtual PVR here for 440EP as 440EP and 440GR have
+ * identical PVRs and there is no reliable way to check for the FPU
+ */
+ spec = identify_cpu(offset, (mfspr(SPRN_PVR) | 0x8));
+#else
spec = identify_cpu(offset, mfspr(SPRN_PVR));
+#endif
do_feature_fixups(spec->cpu_features,
PTRRELOC(&__start___ftr_fixup),
PTRRELOC(&__stop___ftr_fixup));
* That means the zeroed TLB has to be invalidated
* whenever a page miss occurs.
*/
- _tlbie(address);
+ _tlbie(address, 0 /* 8xx doesn't care about PID */);
#endif
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
* architectures. -- Dan
*/
#if defined(CONFIG_8xx)
-#define flush_HPTE(X, va, pg) _tlbie(va)
+#define flush_HPTE(X, va, pg) _tlbie(va, 0 /* 8xx doesn't care about PID */)
#define MMU_init_hw() do { } while(0)
#define mmu_mapin_ram() (0UL)
break;
default:
+ iounmap(pcie_reg_fpga_base);
return;
}
}, \
}
+#define XPAR_AC97_CONTROLLER_REFERENCE(num) { \
+ .name = "ml403_ac97cr", \
+ .id = num, \
+ .num_resources = 3, \
+ .resource = (struct resource[]) { \
+ { \
+ .start = XPAR_OPB_AC97_CONTROLLER_REF_##num##_BASEADDR, \
+ .end = XPAR_OPB_AC97_CONTROLLER_REF_##num##_HIGHADDR, \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \
+ .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ { \
+ .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \
+ .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ }, \
+}
+
/* UART 8250 driver platform data table */
struct plat_serial8250_port virtex_serial_platform_data[] = {
#if defined(XPAR_UARTNS550_0_BASEADDR)
#if defined(XPAR_TFT_3_BASEADDR)
XPAR_TFT(3),
#endif
+
+ /* AC97 Controller Reference instances */
+#if defined(XPAR_OPB_AC97_CONTROLLER_REF_0_BASEADDR)
+ XPAR_AC97_CONTROLLER_REFERENCE(0),
+#endif
+#if defined(XPAR_OPB_AC97_CONTROLLER_REF_1_BASEADDR)
+ XPAR_AC97_CONTROLLER_REFERENCE(1),
+#endif
};
/* Early serial support functions */
int active; /* monitoring status */
/* fill in from here */
- unsigned int ctl_nr; /* sysctl ID */
char name[APPLDATA_PROC_NAME_LENGTH]; /* name of /proc fs node */
unsigned char record_nr; /* Record Nr. for Product ID */
void (*callback)(void *data); /* callback function */
static struct ctl_table_header *appldata_sysctl_header;
static struct ctl_table appldata_table[] = {
{
- .ctl_name = CTL_APPLDATA_TIMER,
.procname = "timer",
.mode = S_IRUGO | S_IWUSR,
.proc_handler = &appldata_timer_handler,
},
{
- .ctl_name = CTL_APPLDATA_INTERVAL,
.procname = "interval",
.mode = S_IRUGO | S_IWUSR,
.proc_handler = &appldata_interval_handler,
},
- { .ctl_name = 0 }
+ { },
};
static struct ctl_table appldata_dir_table[] = {
{
- .ctl_name = CTL_APPLDATA,
.procname = appldata_proc_name,
.maxlen = 0,
.mode = S_IRUGO | S_IXUGO,
.child = appldata_table,
},
- { .ctl_name = 0 }
+ { },
};
/*
*/
int appldata_register_ops(struct appldata_ops *ops)
{
- struct list_head *lh;
- struct appldata_ops *tmp_ops;
- int i;
-
- i = 0;
+ if ((ops->size > APPLDATA_MAX_REC_SIZE) || (ops->size < 0))
+ return -EINVAL;
- if ((ops->size > APPLDATA_MAX_REC_SIZE) ||
- (ops->size < 0)){
- P_ERROR("Invalid size of %s record = %i, maximum = %i!\n",
- ops->name, ops->size, APPLDATA_MAX_REC_SIZE);
- return -ENOMEM;
- }
- if ((ops->ctl_nr == CTL_APPLDATA) ||
- (ops->ctl_nr == CTL_APPLDATA_TIMER) ||
- (ops->ctl_nr == CTL_APPLDATA_INTERVAL)) {
- P_ERROR("ctl_nr %i already in use!\n", ops->ctl_nr);
- return -EBUSY;
- }
- ops->ctl_table = kzalloc(4*sizeof(struct ctl_table), GFP_KERNEL);
- if (ops->ctl_table == NULL) {
- P_ERROR("Not enough memory for %s ctl_table!\n", ops->name);
+ ops->ctl_table = kzalloc(4 * sizeof(struct ctl_table), GFP_KERNEL);
+ if (!ops->ctl_table)
return -ENOMEM;
- }
spin_lock(&appldata_ops_lock);
- list_for_each(lh, &appldata_ops_list) {
- tmp_ops = list_entry(lh, struct appldata_ops, list);
- P_DEBUG("register_ops loop: %i) name = %s, ctl = %i\n",
- ++i, tmp_ops->name, tmp_ops->ctl_nr);
- P_DEBUG("Comparing %s (ctl %i) with %s (ctl %i)\n",
- tmp_ops->name, tmp_ops->ctl_nr, ops->name,
- ops->ctl_nr);
- if (strncmp(tmp_ops->name, ops->name,
- APPLDATA_PROC_NAME_LENGTH) == 0) {
- P_ERROR("Name \"%s\" already registered!\n", ops->name);
- kfree(ops->ctl_table);
- spin_unlock(&appldata_ops_lock);
- return -EBUSY;
- }
- if (tmp_ops->ctl_nr == ops->ctl_nr) {
- P_ERROR("ctl_nr %i already registered!\n", ops->ctl_nr);
- kfree(ops->ctl_table);
- spin_unlock(&appldata_ops_lock);
- return -EBUSY;
- }
- }
list_add(&ops->list, &appldata_ops_list);
spin_unlock(&appldata_ops_lock);
- ops->ctl_table[0].ctl_name = CTL_APPLDATA;
ops->ctl_table[0].procname = appldata_proc_name;
ops->ctl_table[0].maxlen = 0;
ops->ctl_table[0].mode = S_IRUGO | S_IXUGO;
ops->ctl_table[0].child = &ops->ctl_table[2];
- ops->ctl_table[1].ctl_name = 0;
-
- ops->ctl_table[2].ctl_name = ops->ctl_nr;
ops->ctl_table[2].procname = ops->name;
ops->ctl_table[2].mode = S_IRUGO | S_IWUSR;
ops->ctl_table[2].proc_handler = appldata_generic_handler;
ops->ctl_table[2].data = ops;
- ops->ctl_table[3].ctl_name = 0;
-
ops->sysctl_header = register_sysctl_table(ops->ctl_table);
-
+ if (!ops->sysctl_header)
+ goto out;
P_INFO("%s-ops registered!\n", ops->name);
return 0;
+out:
+ spin_lock(&appldata_ops_lock);
+ list_del(&ops->list);
+ spin_unlock(&appldata_ops_lock);
+ kfree(ops->ctl_table);
+ return -ENOMEM;
}
/*
*/
void appldata_unregister_ops(struct appldata_ops *ops)
{
- void *table;
spin_lock(&appldata_ops_lock);
list_del(&ops->list);
- /* at that point any incoming access will fail */
- table = ops->ctl_table;
- ops->ctl_table = NULL;
spin_unlock(&appldata_ops_lock);
unregister_sysctl_table(ops->sysctl_header);
- kfree(table);
+ kfree(ops->ctl_table);
P_INFO("%s-ops unregistered!\n", ops->name);
}
/********************** module-ops management <END> **************************/
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_MEM,
.name = "mem",
.record_nr = APPLDATA_RECORD_MEM_ID,
.size = sizeof(struct appldata_mem_data),
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_NET_SUM,
.name = "net_sum",
.record_nr = APPLDATA_RECORD_NET_SUM_ID,
.size = sizeof(struct appldata_net_sum_data),
static struct appldata_os_data *appldata_os_data;
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_OS,
.name = "os",
.record_nr = APPLDATA_RECORD_OS_ID,
.owner = THIS_MODULE,
cc = __tprot(addr);
while (cc == old_cc) {
addr += CHUNK_INCR;
- if (addr >= memsize)
+ if (memsize && addr >= memsize)
break;
#ifndef CONFIG_64BIT
if (addr == ADDR2G)
basr %r14,%r1
.endm
- .macro LOCKDEP_SYS_EXIT
- l %r1,BASED(.Llockdep_sys_exit)
+ .macro TRACE_IRQS_CHECK
+ tm SP_PSW(%r15),0x03 # irqs enabled?
+ jz 0f
+ l %r1,BASED(.Ltrace_irq_on)
basr %r14,%r1
+ j 1f
+0: l %r1,BASED(.Ltrace_irq_off)
+ basr %r14,%r1
+1:
.endm
#else
#define TRACE_IRQS_ON
#define TRACE_IRQS_OFF
+#define TRACE_IRQS_CHECK
+#endif
+
+#ifdef CONFIG_LOCKDEP
+ .macro LOCKDEP_SYS_EXIT
+ tm SP_PSW+1(%r15),0x01 # returning to user ?
+ jz 0f
+ l %r1,BASED(.Llockdep_sys_exit)
+ basr %r14,%r1
+0:
+ .endm
+#else
#define LOCKDEP_SYS_EXIT
#endif
lh %r7,0x8a # get svc number from lowcore
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
sysc_vtime:
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(sysc_do_svc)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
sysc_stime:
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
sysc_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
- bno BASED(sysc_leave)
+ bno BASED(sysc_restore)
tm __TI_flags+3(%r9),_TIF_WORK_SVC
bnz BASED(sysc_work) # there is work to do (signals etc.)
+sysc_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ la %r1,BASED(sysc_restore_trace_psw)
+ lpsw 0(%r1)
+sysc_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
sysc_leave:
RESTORE_ALL __LC_RETURN_PSW,1
+sysc_done:
+
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl sysc_restore_trace_psw
+sysc_restore_trace_psw:
+ .long 0, sysc_restore_trace + 0x80000000
+#endif
#
# recheck if there is more work to do
#
sysc_work_loop:
tm __TI_flags+3(%r9),_TIF_WORK_SVC
- bz BASED(sysc_leave) # there is no work to do
+ bz BASED(sysc_restore) # there is no work to do
#
# One of the work bits is on. Find out which one.
#
bo BASED(sysc_restart)
tm __TI_flags+3(%r9),_TIF_SINGLE_STEP
bo BASED(sysc_singlestep)
- LOCKDEP_SYS_EXIT
- b BASED(sysc_leave)
+ b BASED(sysc_restore)
+sysc_work_done:
#
# _TIF_NEED_RESCHED is set, call schedule
pgm_no_vtime:
#endif
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r3,__LC_PGM_ILC # load program interruption code
la %r8,0x7f
nr %r8,%r3
pgm_no_vtime2:
#endif
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r1,__TI_task(%r9)
mvc __THREAD_per+__PER_atmid(2,%r1),__LC_PER_ATMID
mvc __THREAD_per+__PER_address(4,%r1),__LC_PER_ADDRESS
SAVE_ALL_SYNC __LC_SVC_OLD_PSW,__LC_SAVE_AREA
CREATE_STACK_FRAME __LC_SVC_OLD_PSW,__LC_SAVE_AREA
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(pgm_no_vtime3)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-pgm_no_vtime3:
#endif
lh %r7,0x8a # get svc number from lowcore
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r1,__TI_task(%r9)
mvc __THREAD_per+__PER_atmid(2,%r1),__LC_PER_ATMID
mvc __THREAD_per+__PER_address(4,%r1),__LC_PER_ADDRESS
mvi SP_TRAP+1(%r15),0x28 # set trap indication to pgm check
la %r2,SP_PTREGS(%r15) # address of register-save area
l %r1,BASED(.Lhandle_per) # load adr. of per handler
- la %r14,BASED(sysc_leave) # load adr. of system return
+ la %r14,BASED(sysc_restore)# load adr. of system return
br %r1 # branch to do_single_step
/*
l %r1,BASED(.Ldo_IRQ) # load address of do_IRQ
la %r2,SP_PTREGS(%r15) # address of register-save area
basr %r14,%r1 # branch to standard irq handler
- TRACE_IRQS_ON
-
io_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
#ifdef CONFIG_PREEMPT
bno BASED(io_preempt) # no -> check for preemptive scheduling
#else
- bno BASED(io_leave) # no-> skip resched & signal
+ bno BASED(io_restore) # no-> skip resched & signal
#endif
tm __TI_flags+3(%r9),_TIF_WORK_INT
bnz BASED(io_work) # there is work to do (signals etc.)
+io_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ la %r1,BASED(io_restore_trace_psw)
+ lpsw 0(%r1)
+io_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
io_leave:
RESTORE_ALL __LC_RETURN_PSW,0
io_done:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl io_restore_trace_psw
+io_restore_trace_psw:
+ .long 0, io_restore_trace + 0x80000000
+#endif
+
#ifdef CONFIG_PREEMPT
io_preempt:
icm %r0,15,__TI_precount(%r9)
- bnz BASED(io_leave)
+ bnz BASED(io_restore)
l %r1,SP_R15(%r15)
s %r1,BASED(.Lc_spsize)
mvc SP_PTREGS(__PT_SIZE,%r1),SP_PTREGS(%r15)
lr %r15,%r1
io_resume_loop:
tm __TI_flags+3(%r9),_TIF_NEED_RESCHED
- bno BASED(io_leave)
- mvc __TI_precount(4,%r9),BASED(.Lc_pactive)
- stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
- l %r1,BASED(.Lschedule)
- basr %r14,%r1 # call schedule
- stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
- xc __TI_precount(4,%r9),__TI_precount(%r9)
- b BASED(io_resume_loop)
+ bno BASED(io_restore)
+ l %r1,BASED(.Lpreempt_schedule_irq)
+ la %r14,BASED(io_resume_loop)
+ br %r1 # call schedule
#endif
#
bo BASED(io_reschedule)
tm __TI_flags+3(%r9),(_TIF_SIGPENDING | _TIF_RESTORE_SIGMASK)
bnz BASED(io_sigpending)
- LOCKDEP_SYS_EXIT
- b BASED(io_leave)
+ b BASED(io_restore)
+io_work_done:
#
# _TIF_MCCK_PENDING is set, call handler
#
io_mcck_pending:
- TRACE_IRQS_OFF
l %r1,BASED(.Ls390_handle_mcck)
basr %r14,%r1 # TIF bit will be cleared by handler
- TRACE_IRQS_ON
b BASED(io_work_loop)
#
# _TIF_NEED_RESCHED is set, call schedule
#
io_reschedule:
+ TRACE_IRQS_ON
l %r1,BASED(.Lschedule)
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
basr %r14,%r1 # call scheduler
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
tm __TI_flags+3(%r9),_TIF_WORK_INT
- bz BASED(io_leave) # there is no work to do
+ bz BASED(io_restore) # there is no work to do
b BASED(io_work_loop)
#
# _TIF_SIGPENDING or _TIF_RESTORE_SIGMASK is set, call do_signal
#
io_sigpending:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
la %r2,SP_PTREGS(%r15) # load pt_regs
l %r1,BASED(.Ldo_signal)
basr %r14,%r1 # call do_signal
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
b BASED(io_work_loop)
/*
lh %r3,__LC_EXT_INT_CODE # get interruption code
l %r1,BASED(.Ldo_extint)
basr %r14,%r1
- TRACE_IRQS_ON
b BASED(io_return)
__critical_end:
cleanup_table_sysc_return:
.long sysc_return + 0x80000000, sysc_leave + 0x80000000
cleanup_table_sysc_leave:
- .long sysc_leave + 0x80000000, sysc_work_loop + 0x80000000
+ .long sysc_leave + 0x80000000, sysc_done + 0x80000000
cleanup_table_sysc_work_loop:
- .long sysc_work_loop + 0x80000000, sysc_reschedule + 0x80000000
+ .long sysc_work_loop + 0x80000000, sysc_work_done + 0x80000000
cleanup_table_io_return:
.long io_return + 0x80000000, io_leave + 0x80000000
cleanup_table_io_leave:
.long io_leave + 0x80000000, io_done + 0x80000000
cleanup_table_io_work_loop:
- .long io_work_loop + 0x80000000, io_mcck_pending + 0x80000000
+ .long io_work_loop + 0x80000000, io_work_done + 0x80000000
cleanup_critical:
clc 4(4,%r12),BASED(cleanup_table_system_call)
cleanup_vtime:
clc __LC_RETURN_PSW+4(4),BASED(cleanup_system_call_insn+12)
bhe BASED(cleanup_stime)
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(cleanup_novtime)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
cleanup_stime:
clc __LC_RETURN_PSW+4(4),BASED(cleanup_system_call_insn+16)
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
cleanup_update:
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-cleanup_novtime:
#endif
mvc __LC_RETURN_PSW+4(4),BASED(cleanup_table_system_call+4)
la %r12,__LC_RETURN_PSW
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_sysc_leave_insn:
+ .long sysc_done - 4 + 0x80000000
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .long sysc_leave + 14 + 0x80000000
+ .long sysc_done - 8 + 0x80000000
#endif
- .long sysc_leave + 10 + 0x80000000
cleanup_io_return:
mvc __LC_RETURN_PSW(4),0(%r12)
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_io_leave_insn:
+ .long io_done - 4 + 0x80000000
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .long io_leave + 18 + 0x80000000
+ .long io_done - 8 + 0x80000000
#endif
- .long io_leave + 14 + 0x80000000
/*
* Integer constants
.align 4
.Lc_spsize: .long SP_SIZE
.Lc_overhead: .long STACK_FRAME_OVERHEAD
-.Lc_pactive: .long PREEMPT_ACTIVE
.Lnr_syscalls: .long NR_syscalls
.L0x018: .short 0x018
.L0x020: .short 0x020
.Lexecve_tail: .long execve_tail
.Ljump_table: .long pgm_check_table
.Lschedule: .long schedule
+.Lpreempt_schedule_irq:
+ .long preempt_schedule_irq
.Ltrace: .long syscall_trace
.Lschedtail: .long schedule_tail
.Lsysc_table: .long sys_call_table
brasl %r14,trace_hardirqs_off
.endm
- .macro LOCKDEP_SYS_EXIT
- brasl %r14,lockdep_sys_exit
+ .macro TRACE_IRQS_CHECK
+ tm SP_PSW(%r15),0x03 # irqs enabled?
+ jz 0f
+ brasl %r14,trace_hardirqs_on
+ j 1f
+0: brasl %r14,trace_hardirqs_off
+1:
.endm
#else
#define TRACE_IRQS_ON
#define TRACE_IRQS_OFF
+#define TRACE_IRQS_CHECK
+#endif
+
+#ifdef CONFIG_LOCKDEP
+ .macro LOCKDEP_SYS_EXIT
+ tm SP_PSW+1(%r15),0x01 # returning to user ?
+ jz 0f
+ brasl %r14,lockdep_sys_exit
+0:
+ .endm
+#else
#define LOCKDEP_SYS_EXIT
#endif
llgh %r7,__LC_SVC_INT_CODE # get svc number from lowcore
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
sysc_vtime:
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz sysc_do_svc
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
sysc_stime:
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
sysc_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
- jno sysc_leave
+ jno sysc_restore
tm __TI_flags+7(%r9),_TIF_WORK_SVC
jnz sysc_work # there is work to do (signals etc.)
+sysc_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ larl %r1,sysc_restore_trace_psw
+ lpswe 0(%r1)
+sysc_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
sysc_leave:
RESTORE_ALL __LC_RETURN_PSW,1
+sysc_done:
+
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl sysc_restore_trace_psw
+sysc_restore_trace_psw:
+ .quad 0, sysc_restore_trace
+#endif
#
# recheck if there is more work to do
#
sysc_work_loop:
tm __TI_flags+7(%r9),_TIF_WORK_SVC
- jz sysc_leave # there is no work to do
+ jz sysc_restore # there is no work to do
#
# One of the work bits is on. Find out which one.
#
jo sysc_restart
tm __TI_flags+7(%r9),_TIF_SINGLE_STEP
jo sysc_singlestep
- LOCKDEP_SYS_EXIT
- j sysc_leave
+ j sysc_restore
+sysc_work_done:
#
# _TIF_NEED_RESCHED is set, call schedule
pgm_no_vtime:
#endif
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
lgf %r3,__LC_PGM_ILC # load program interruption code
lghi %r8,0x7f
ngr %r8,%r3
pgm_no_vtime2:
#endif
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
lg %r1,__TI_task(%r9)
tm SP_PSW+1(%r15),0x01 # kernel per event ?
jz kernel_per
SAVE_ALL_SYNC __LC_SVC_OLD_PSW,__LC_SAVE_AREA
CREATE_STACK_FRAME __LC_SVC_OLD_PSW,__LC_SAVE_AREA
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz pgm_no_vtime3
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-pgm_no_vtime3:
#endif
llgh %r7,__LC_SVC_INT_CODE # get svc number from lowcore
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
lhi %r0,__LC_PGM_OLD_PSW
sth %r0,SP_TRAP(%r15) # set trap indication to pgm check
la %r2,SP_PTREGS(%r15) # address of register-save area
- larl %r14,sysc_leave # load adr. of system ret, no work
+ larl %r14,sysc_restore # load adr. of system ret, no work
jg do_single_step # branch to do_single_step
/*
TRACE_IRQS_OFF
la %r2,SP_PTREGS(%r15) # address of register-save area
brasl %r14,do_IRQ # call standard irq handler
- TRACE_IRQS_ON
-
io_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
#ifdef CONFIG_PREEMPT
jno io_preempt # no -> check for preemptive scheduling
#else
- jno io_leave # no-> skip resched & signal
+ jno io_restore # no-> skip resched & signal
#endif
tm __TI_flags+7(%r9),_TIF_WORK_INT
jnz io_work # there is work to do (signals etc.)
+io_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ larl %r1,io_restore_trace_psw
+ lpswe 0(%r1)
+io_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
io_leave:
RESTORE_ALL __LC_RETURN_PSW,0
io_done:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl io_restore_trace_psw
+io_restore_trace_psw:
+ .quad 0, io_restore_trace
+#endif
+
#ifdef CONFIG_PREEMPT
io_preempt:
icm %r0,15,__TI_precount(%r9)
- jnz io_leave
+ jnz io_restore
# switch to kernel stack
lg %r1,SP_R15(%r15)
aghi %r1,-SP_SIZE
lgr %r15,%r1
io_resume_loop:
tm __TI_flags+7(%r9),_TIF_NEED_RESCHED
- jno io_leave
- larl %r1,.Lc_pactive
- mvc __TI_precount(4,%r9),0(%r1)
- stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
- brasl %r14,schedule # call schedule
- stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
- xc __TI_precount(4,%r9),__TI_precount(%r9)
- j io_resume_loop
+ jno io_restore
+ larl %r14,io_resume_loop
+ jg preempt_schedule_irq
#endif
#
jo io_reschedule
tm __TI_flags+7(%r9),(_TIF_SIGPENDING | _TIF_RESTORE_SIGMASK)
jnz io_sigpending
- LOCKDEP_SYS_EXIT
- j io_leave
+ j io_restore
+io_work_done:
#
# _TIF_MCCK_PENDING is set, call handler
#
io_mcck_pending:
- TRACE_IRQS_OFF
brasl %r14,s390_handle_mcck # TIF bit will be cleared by handler
- TRACE_IRQS_ON
j io_work_loop
#
# _TIF_NEED_RESCHED is set, call schedule
#
io_reschedule:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
brasl %r14,schedule # call scheduler
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
tm __TI_flags+7(%r9),_TIF_WORK_INT
- jz io_leave # there is no work to do
+ jz io_restore # there is no work to do
j io_work_loop
#
# _TIF_SIGPENDING or _TIF_RESTORE_SIGMASK is set, call do_signal
#
io_sigpending:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
la %r2,SP_PTREGS(%r15) # load pt_regs
brasl %r14,do_signal # call do_signal
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
j io_work_loop
/*
la %r2,SP_PTREGS(%r15) # address of register-save area
llgh %r3,__LC_EXT_INT_CODE # get interruption code
brasl %r14,do_extint
- TRACE_IRQS_ON
j io_return
__critical_end:
cleanup_table_sysc_return:
.quad sysc_return, sysc_leave
cleanup_table_sysc_leave:
- .quad sysc_leave, sysc_work_loop
+ .quad sysc_leave, sysc_done
cleanup_table_sysc_work_loop:
- .quad sysc_work_loop, sysc_reschedule
+ .quad sysc_work_loop, sysc_work_done
cleanup_table_io_return:
.quad io_return, io_leave
cleanup_table_io_leave:
.quad io_leave, io_done
cleanup_table_io_work_loop:
- .quad io_work_loop, io_mcck_pending
+ .quad io_work_loop, io_work_done
cleanup_critical:
clc 8(8,%r12),BASED(cleanup_table_system_call)
cleanup_vtime:
clc __LC_RETURN_PSW+8(8),BASED(cleanup_system_call_insn+24)
jhe cleanup_stime
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz cleanup_novtime
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
cleanup_stime:
clc __LC_RETURN_PSW+8(8),BASED(cleanup_system_call_insn+32)
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
cleanup_update:
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-cleanup_novtime:
#endif
mvc __LC_RETURN_PSW+8(8),BASED(cleanup_table_system_call+8)
la %r12,__LC_RETURN_PSW
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_sysc_leave_insn:
+ .quad sysc_done - 4
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .quad sysc_leave + 16
+ .quad sysc_done - 8
#endif
- .quad sysc_leave + 12
cleanup_io_return:
mvc __LC_RETURN_PSW(8),0(%r12)
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_io_leave_insn:
+ .quad io_done - 4
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .quad io_leave + 20
+ .quad io_done - 8
#endif
- .quad io_leave + 16
/*
* Integer constants
*/
.align 4
.Lconst:
-.Lc_pactive: .long PREEMPT_ACTIVE
.Lnr_syscalls: .long NR_syscalls
.L0x0130: .short 0x130
.L0x0140: .short 0x140
void machine_restart(char *command)
{
- if (!in_interrupt() || oops_in_progress)
+ if ((!in_interrupt() && !in_atomic()) || oops_in_progress)
/*
* Only unblank the console if we are called in enabled
* context or a bust_spinlocks cleared the way for us.
printk("S390 address spaces switched, ");
set_amode_and_uaccess(PSW_ASC_PRIMARY, PSW32_ASC_PRIMARY);
}
+#ifdef CONFIG_TRACE_IRQFLAGS
+ sysc_restore_trace_psw.mask = psw_kernel_bits & ~PSW_MASK_MCHECK;
+ io_restore_trace_psw.mask = psw_kernel_bits & ~PSW_MASK_MCHECK;
+#endif
}
static void __init
}
EXPORT_SYMBOL(smp_call_function_single);
-static void do_send_stop(void)
+void smp_send_stop(void)
{
int cpu, rc;
- /* stop all processors */
- for_each_online_cpu(cpu) {
- if (cpu == smp_processor_id())
- continue;
- do {
- rc = signal_processor(cpu, sigp_stop);
- } while (rc == sigp_busy);
- }
-}
+ /* Disable all interrupts/machine checks */
+ __load_psw_mask(psw_kernel_bits & ~PSW_MASK_MCHECK);
-static void do_store_status(void)
-{
- int cpu, rc;
+ /* write magic number to zero page (absolute 0) */
+ lowcore_ptr[smp_processor_id()]->panic_magic = __PANIC_MAGIC;
- /* store status of all processors in their lowcores (real 0) */
+ /* stop all processors */
for_each_online_cpu(cpu) {
if (cpu == smp_processor_id())
continue;
do {
- rc = signal_processor_p(
- (__u32)(unsigned long) lowcore_ptr[cpu], cpu,
- sigp_store_status_at_address);
+ rc = signal_processor(cpu, sigp_stop);
} while (rc == sigp_busy);
- }
-}
-static void do_wait_for_stop(void)
-{
- int cpu;
-
- /* Wait for all other cpus to enter stopped state */
- for_each_online_cpu(cpu) {
- if (cpu == smp_processor_id())
- continue;
while (!smp_cpu_not_running(cpu))
cpu_relax();
}
}
-/*
- * this function sends a 'stop' sigp to all other CPUs in the system.
- * it goes straight through.
- */
-void smp_send_stop(void)
-{
- /* Disable all interrupts/machine checks */
- __load_psw_mask(psw_kernel_bits & ~PSW_MASK_MCHECK);
-
- /* write magic number to zero page (absolute 0) */
- lowcore_ptr[smp_processor_id()]->panic_magic = __PANIC_MAGIC;
-
- /* stop other processors. */
- do_send_stop();
-
- /* wait until other processors are stopped */
- do_wait_for_stop();
-
- /* store status of other processors. */
- do_store_status();
-}
-
/*
* Reboot, halt and power_off routines for SMP.
*/
bust_spinlocks(1);
printk("%s: %04lx [#%d]\n", str, err & 0xffff, ++die_counter);
print_modules();
+ notify_die(DIE_OOPS, str, regs, err, current->thread.trap_no, SIGSEGV);
show_regs(regs);
bust_spinlocks(0);
add_taint(TAINT_DIE);
static struct ctl_table cmm_table[] = {
{
- .ctl_name = VM_CMM_PAGES,
.procname = "cmm_pages",
.mode = 0644,
.proc_handler = &cmm_pages_handler,
},
{
- .ctl_name = VM_CMM_TIMED_PAGES,
.procname = "cmm_timed_pages",
.mode = 0644,
.proc_handler = &cmm_pages_handler,
},
{
- .ctl_name = VM_CMM_TIMEOUT,
.procname = "cmm_timeout",
.mode = 0644,
.proc_handler = &cmm_timeout_handler,
.end = PA_AREA5_IO + 0x80c,
.flags = IORESOURCE_MEM,
},
+#ifndef CONFIG_RTS7751R2D_1 /* For R2D-1 polling is preferred */
[2] = {
.start = IRQ_CF_IDE,
.flags = IORESOURCE_IRQ,
},
+#endif
};
static struct pata_platform_info pata_info = {
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22-rc4
-# Mon Jun 11 10:24:57 2007
+# Linux kernel version: 2.6.24-rc2
+# Tue Nov 13 20:32:39 2007
#
CONFIG_SUPERH=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_SYS_SUPPORTS_PCI=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
+# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_ANON_INODES=y
# CONFIG_EPOLL is not set
CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_SLOB is not set
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-
-#
-# Loadable module support
-#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
#
# IO Schedulers
CONFIG_CPU_SH4A=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
-# CONFIG_CPU_SUBTYPE_SH7300 is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
+# CONFIG_CPU_SUBTYPE_SH7720 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
# CONFIG_CPU_SUBTYPE_SH7785 is not set
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
-# CONFIG_SH_WRITETHROUGH is not set
-# CONFIG_SH_OCRAM is not set
+CONFIG_CACHE_WRITEBACK=y
+# CONFIG_CACHE_WRITETHROUGH is not set
+# CONFIG_CACHE_OFF is not set
#
# Processor features
CONFIG_CPU_LITTLE_ENDIAN=y
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_SH_FPU=y
-# CONFIG_SH_DSP is not set
CONFIG_SH_STORE_QUEUES=y
CONFIG_SPECULATIVE_EXECUTION=y
CONFIG_CPU_HAS_INTEVT=y
-CONFIG_CPU_HAS_INTC_IRQ=y
CONFIG_CPU_HAS_SR_RB=y
+CONFIG_CPU_HAS_FPU=y
#
# Board support
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
# Companion Chips
#
-# CONFIG_HD6446X_SERIES is not set
#
# Additional SuperH Device Drivers
CONFIG_HZ=250
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
-# CONFIG_SMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
+CONFIG_GUSA=y
#
# Boot options
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
-# CONFIG_UBC_WAKEUP is not set
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
CONFIG_PCI_AUTO=y
CONFIG_PCI_AUTO_UPDATE_RESOURCES=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
-#
-# Power management options (EXPERIMENTAL)
-#
-# CONFIG_PM is not set
-
#
# Networking
#
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_CPQ_DA is not set
+CONFIG_BLK_DEV=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
+CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
+CONFIG_EEPROM_93CX6=y
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-# CONFIG_BLINK is not set
# CONFIG_IDE is not set
#
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
-# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
-
-#
-# SCSI low-level drivers
-#
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
-# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_PATA_PLATFORM=y
-
-#
-# Multi-device support (RAID and LVM)
-#
# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
# CONFIG_I2O is not set
-
-#
-# Network device support
-#
CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_AX88796=y
+CONFIG_AX88796_93CX6=y
# CONFIG_STNIC is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
-
-#
-# Tulip family network device support
-#
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
# CONFIG_PCNET32_NAPI is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
CONFIG_E1000=m
# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
# CONFIG_TR is not set
#
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
# Graphics support
#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_FB is not set
#
# Sound
# Open Sound System
#
CONFIG_SOUND_PRIME=m
-# CONFIG_OSS_OBSOLETE is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
-
-#
-# HID Devices
-#
+CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set
-#
-# I2C RTC drivers
-#
-
#
# SPI RTC drivers
#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
CONFIG_RTC_DRV_SH=y
#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
+# Userspace I/O
#
+# CONFIG_UIO is not set
#
# File systems
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=m
#
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-
-#
-# Profiling support
-#
+CONFIG_INSTRUMENTATION=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
+# CONFIG_MARKERS is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
+# CONFIG_IRQSTACKS is not set
# CONFIG_SH_KGDB is not set
#
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_PCBC=m
# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_TEST is not set
-
-#
-# Hardware crypto devices
-#
+# CONFIG_CRYPTO_AUTHENC is not set
+CONFIG_CRYPTO_HW=y
#
# Library routines
# CONFIG_CRC16 is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc1
-# Fri Nov 2 14:30:49 2007
+# Linux kernel version: 2.6.24-rc2
+# Tue Nov 13 20:34:57 2007
#
CONFIG_SUPERH=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_CPU_SUBTYPE_SH7785=y
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
-# CONFIG_UBC_WAKEUP is not set
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
CONFIG_PCI_AUTO=y
CONFIG_PCI_AUTO_UPDATE_RESOURCES=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_AX88796=y
+CONFIG_AX88796_93CX6=y
# CONFIG_STNIC is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
pmd_t *pmd;
pte_t *pte;
pte_t entry;
- struct mm_struct *mm = current->mm;
- spinlock_t *ptl = NULL;
- int ret = 1;
#ifdef CONFIG_SH_KGDB
if (kgdb_nofault && kgdb_bus_err_hook)
*/
if (address >= P3SEG && address < P3_ADDR_MAX) {
pgd = pgd_offset_k(address);
- mm = NULL;
} else {
- if (unlikely(address >= TASK_SIZE || !mm))
+ if (unlikely(address >= TASK_SIZE || !current->mm))
return 1;
- pgd = pgd_offset(mm, address);
+ pgd = pgd_offset(current->mm, address);
}
pud = pud_offset(pgd, address);
if (pmd_none_or_clear_bad(pmd))
return 1;
- if (mm)
- pte = pte_offset_map_lock(mm, pmd, address, &ptl);
- else
- pte = pte_offset_kernel(pmd, address);
-
+ pte = pte_offset_kernel(pmd, address);
entry = *pte;
if (unlikely(pte_none(entry) || pte_not_present(entry)))
- goto unlock;
+ return 1;
if (unlikely(writeaccess && !pte_write(entry)))
- goto unlock;
+ return 1;
if (writeaccess)
entry = pte_mkdirty(entry);
entry = pte_mkyoung(entry);
-#ifdef CONFIG_CPU_SH4
- /*
- * ITLB is not affected by "ldtlb" instruction.
- * So, we need to flush the entry by ourselves.
- */
- local_flush_tlb_one(get_asid(), address & PAGE_MASK);
-#endif
-
set_pte(pte, entry);
update_mmu_cache(NULL, address, entry);
- ret = 0;
-unlock:
- if (mm)
- pte_unmap_unlock(pte, ptl);
- return ret;
+
+ return 0;
}
$(srctree)/arch/x86/Makefile%: ;
ifeq ($(CONFIG_X86_32),y)
+ UTS_MACHINE := i386
include $(srctree)/arch/x86/Makefile_32
else
+ UTS_MACHINE := x86_64
include $(srctree)/arch/x86/Makefile_64
endif
-
-
-
if (cpu_has(c, X86_FEATURE_EST))
buf[2] |= ACPI_PDC_EST_CAPABILITY_SWSMP;
+ if (cpu_has(c, X86_FEATURE_ACPI))
+ buf[2] |= ACPI_PDC_T_FFH;
+
obj->type = ACPI_TYPE_BUFFER;
obj->buffer.length = 12;
obj->buffer.pointer = (u8 *) buf;
__setup("acpi_sleep=", acpi_sleep_setup);
-void acpi_pci_link_exit(void)
-{
-}
* Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
* needed on AMD.
*/
- if (modern_apic())
+ if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
return;
/*
* Wait for idle.
#include <asm/semaphore.h>
#include <asm/checksum.h>
#include <asm/desc.h>
+#include <asm/pgtable.h>
EXPORT_SYMBOL(__down_failed);
EXPORT_SYMBOL(__down_failed_interruptible);
#endif
EXPORT_SYMBOL(csum_partial);
+EXPORT_SYMBOL(empty_zero_page);
#define default_MCA_trigger(idx) (1)
#define default_MCA_polarity(idx) (0)
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].mpc_srcbus;
int polarity;
{
int apic1, pin1, apic2, pin2;
int vector;
+ unsigned int ver;
+
+ ver = apic_read(APIC_LVR);
+ ver = GET_APIC_VERSION(ver);
/*
* get/set the timer IRQ vector:
* mode for the 8259A whenever interrupts are routed
* through I/O APICs. Also IRQ0 has to be enabled in
* the 8259A which implies the virtual wire has to be
- * disabled in the local APIC.
+ * disabled in the local APIC. Finally timer interrupts
+ * need to be acknowledged manually in the 8259A for
+ * timer_interrupt() and for the i82489DX when using
+ * the NMI watchdog.
*/
apic_write_around(APIC_LVT0, APIC_LVT_MASKED | APIC_DM_EXTINT);
init_8259A(1);
- timer_ack = 1;
+ timer_ack = !cpu_has_tsc;
+ timer_ack |= (nmi_watchdog == NMI_IO_APIC && !APIC_INTEGRATED(ver));
if (timer_over_8254 > 0)
enable_8259A_irq(0);
return 0;
}
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+ int i;
+
+ if (skip_ioapic_setup)
+ return -1;
+
+ for (i = 0; i < mp_irq_entries; i++)
+ if (mp_irqs[i].mpc_irqtype == mp_INT &&
+ mp_irqs[i].mpc_srcbusirq == bus_irq)
+ break;
+ if (i >= mp_irq_entries)
+ return -1;
+
+ *trigger = irq_trigger(i);
+ *polarity = irq_polarity(i);
+ return 0;
+}
+
#endif /* CONFIG_ACPI */
static int __init parse_disable_timer_pin_1(char *arg)
#define default_PCI_trigger(idx) (1)
#define default_PCI_polarity(idx) (1)
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].mpc_srcbus;
int polarity;
return 0;
}
-#endif /* CONFIG_ACPI */
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+ int i;
+
+ if (skip_ioapic_setup)
+ return -1;
+
+ for (i = 0; i < mp_irq_entries; i++)
+ if (mp_irqs[i].mpc_irqtype == mp_INT &&
+ mp_irqs[i].mpc_srcbusirq == bus_irq)
+ break;
+ if (i >= mp_irq_entries)
+ return -1;
+
+ *trigger = irq_trigger(i);
+ *polarity = irq_polarity(i);
+ return 0;
+}
+
+#endif /* CONFIG_ACPI */
/*
* This function currently is only a helper for the i386 smp boot process where
}
}
#endif
+
/*
* returns non-zero if opcode modifies the interrupt flag.
*/
-static __always_inline int is_IF_modifier(kprobe_opcode_t *insn)
+static int __kprobes is_IF_modifier(kprobe_opcode_t *insn)
{
switch (*insn) {
case 0xfa: /* cli */
#include <asm/smp.h>
#include <asm/nmi.h>
+#include <asm/timer.h>
#include "mach_traps.h"
prev_nmi_count = kmalloc(NR_CPUS * sizeof(int), GFP_KERNEL);
if (!prev_nmi_count)
- return -1;
+ goto error;
printk(KERN_INFO "Testing NMI watchdog ... ");
if (!atomic_read(&nmi_active)) {
kfree(prev_nmi_count);
atomic_set(&nmi_active, -1);
- return -1;
+ goto error;
}
printk("OK.\n");
kfree(prev_nmi_count);
return 0;
+error:
+ timer_ack = !cpu_has_tsc;
+
+ return -1;
}
/* This needs to happen later in boot so counters are working */
late_initcall(check_nmi_watchdog);
#include <asm/gart.h>
#include <asm/calgary.h>
-int iommu_merge __read_mostly = 1;
+int iommu_merge __read_mostly = 0;
EXPORT_SYMBOL(iommu_merge);
dma_addr_t bad_dma_address __read_mostly;
{
unsigned long stack;
+ printk("Pid: %d, comm: %.20s %s %s %.*s\n",
+ current->pid, current->comm, print_tainted(),
+ init_utsname()->release,
+ (int)strcspn(init_utsname()->version, " "),
+ init_utsname()->version);
show_trace(current, NULL, &stack);
}
unsigned int condition;
struct task_struct *tsk = current;
+ trace_hardirqs_fixup();
+
get_debugreg(condition, 6);
if (notify_die(DIE_DEBUG, "debug", regs, condition, error_code,
#include <linux/uaccess.h>
#include <linux/bug.h>
#include <linux/kdebug.h>
+#include <linux/utsname.h>
#if defined(CONFIG_EDAC)
#include <linux/edac.h>
void dump_stack(void)
{
unsigned long dummy;
+
+ printk("Pid: %d, comm: %.20s %s %s %.*s\n",
+ current->pid, current->comm, print_tainted(),
+ init_utsname()->release,
+ (int)strcspn(init_utsname()->version, " "),
+ init_utsname()->version);
show_trace(NULL, NULL, &dummy);
}
struct task_struct *tsk = current;
siginfo_t info;
+ trace_hardirqs_fixup();
+
get_debugreg(condition, 6);
if (notify_die(DIE_DEBUG, "debug", regs, condition, error_code,
return 0;
}
-static struct dmi_system_id acpi_pciprobe_dmi_table[] = {
+static struct dmi_system_id acpi_pciprobe_dmi_table[] __devinitdata = {
/*
* Systems where PCI IO resource ISA alignment can be skipped
* when the ISA enable bit in the bridge control is not set
},
},
#endif
+ {
+ .callback = set_bf_sort,
+ .ident = "HP ProLiant DL385 G2",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "HP"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "ProLiant DL385 G2"),
+ },
+ },
+ {
+ .callback = set_bf_sort,
+ .ident = "HP ProLiant DL585 G2",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "HP"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "ProLiant DL585 G2"),
+ },
+ },
{}
};
static struct dentry *blk_create_tree(const char *blk_name)
{
struct dentry *dir = NULL;
+ int created = 0;
mutex_lock(&blk_tree_mutex);
blk_tree_root = debugfs_create_dir("block", NULL);
if (!blk_tree_root)
goto err;
+ created = 1;
}
dir = debugfs_create_dir(blk_name, blk_tree_root);
if (dir)
root_users++;
- else
- blk_remove_root();
+ else {
+ /* Delete root only if we created it */
+ if (created)
+ blk_remove_root();
+ }
err:
mutex_unlock(&blk_tree_mutex);
disk->part = kmalloc_node(size,
GFP_KERNEL | __GFP_ZERO, node_id);
if (!disk->part) {
+ free_disk_stats(disk);
kfree(disk);
return NULL;
}
return queue_var_show(max_hw_sectors_kb, (page));
}
-static ssize_t queue_max_segments_show(struct request_queue *q, char *page)
-{
- return queue_var_show(q->max_phys_segments, page);
-}
-
-static ssize_t queue_max_segments_store(struct request_queue *q,
- const char *page, size_t count)
-{
- unsigned long segments;
- ssize_t ret = queue_var_store(&segments, page, count);
- spin_lock_irq(q->queue_lock);
- q->max_phys_segments = segments;
- spin_unlock_irq(q->queue_lock);
-
- return ret;
-}
static struct queue_sysfs_entry queue_requests_entry = {
.attr = {.name = "nr_requests", .mode = S_IRUGO | S_IWUSR },
.show = queue_requests_show,
.show = queue_max_hw_sectors_show,
};
-static struct queue_sysfs_entry queue_max_segments_entry = {
- .attr = {.name = "max_segments", .mode = S_IRUGO | S_IWUSR },
- .show = queue_max_segments_show,
- .store = queue_max_segments_store,
-};
-
static struct queue_sysfs_entry queue_iosched_entry = {
.attr = {.name = "scheduler", .mode = S_IRUGO | S_IWUSR },
.show = elv_iosched_show,
&queue_ra_entry.attr,
&queue_max_hw_sectors_entry.attr,
&queue_max_sectors_entry.attr,
- &queue_max_segments_entry.attr,
&queue_iosched_entry.attr,
NULL,
};
return;
inst->alg.cra_flags |= CRYPTO_ALG_DEAD;
+ if (hlist_unhashed(&inst->list))
+ return;
+
if (!tmpl || !crypto_tmpl_get(tmpl))
return;
LIST_HEAD(list);
int err = -EINVAL;
- if (inst->alg.cra_destroy)
- goto err;
-
err = crypto_check_alg(&inst->alg);
if (err)
goto err;
.tfm = auth,
};
u8 *hash = aead_request_ctx(req);
- struct scatterlist *dst;
- unsigned int cryptlen;
+ struct scatterlist *dst = req->dst;
+ unsigned int cryptlen = req->cryptlen;
int err;
hash = (u8 *)ALIGN((unsigned long)hash + crypto_hash_alignmask(auth),
if (err)
goto auth_unlock;
- cryptlen = req->cryptlen;
- dst = req->dst;
err = crypto_hash_update(&desc, dst, cryptlen);
if (err)
goto auth_unlock;
};
u8 *ohash = aead_request_ctx(req);
u8 *ihash;
- struct scatterlist *src;
- unsigned int cryptlen;
+ struct scatterlist *src = req->src;
+ unsigned int cryptlen = req->cryptlen;
unsigned int authsize;
int err;
if (err)
goto auth_unlock;
- cryptlen = req->cryptlen;
- src = req->src;
err = crypto_hash_update(&desc, src, cryptlen);
if (err)
goto auth_unlock;
config ACPI_PROCFS
bool "Deprecated /proc/acpi files"
depends on PROC_FS
- default y
---help---
For backwards compatibility, this option allows
deprecated /proc/acpi/ files to exist, even when
/proc/acpi/info (/sys/modules/acpi/parameters/acpica_version)
/proc/acpi/dsdt (/sys/firmware/acpi/tables/DSDT)
/proc/acpi/fadt (/sys/firmware/acpi/tables/FACP)
- /proc/acpi/battery (/sys/class/power_supply)
/proc/acpi/debug_layer (/sys/module/acpi/parameters/debug_layer)
/proc/acpi/debug_level (/sys/module/acpi/parameters/debug_level)
and functions which do not yet exist in /sys.
Say N to delete /proc/acpi/ files that have moved to /sys/
-
+config ACPI_PROCFS_POWER
+ bool "Deprecated power /proc/acpi folders"
+ depends on PROC_FS
+ default y
+ ---help---
+ For backwards compatibility, this option allows
+ deprecated power /proc/acpi/ folders to exist, even when
+ they have been replaced by functions in /sys.
+ The deprecated folders (and their replacements) include:
+ /proc/acpi/battery/* (/sys/class/power_supply/*)
+ /proc/acpi/ac_adapter/* (sys/class/power_supply/*)
+ This option has no effect on /proc/acpi/ folders
+ and functions, which do not yet exist in /sys
+
+ Say N to delete power /proc/acpi/ folders that have moved to /sys/
config ACPI_PROC_EVENT
bool "Deprecated /proc/acpi/event support"
depends on PROC_FS
obj-$(CONFIG_ACPI_ASUS) += asus_acpi.o
obj-$(CONFIG_ACPI_TOSHIBA) += toshiba_acpi.o
obj-$(CONFIG_ACPI_HOTPLUG_MEMORY) += acpi_memhotplug.o
-obj-y += cm_sbs.o
+obj-$(CONFIG_ACPI_PROCFS_POWER) += cm_sbs.o
obj-$(CONFIG_ACPI_SBS) += sbs.o
obj-$(CONFIG_ACPI_SBS) += sbshc.o
#include <linux/module.h>
#include <linux/init.h>
#include <linux/types.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#endif
MODULE_DESCRIPTION("ACPI AC Adapter Driver");
MODULE_LICENSE("GPL");
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
extern struct proc_dir_entry *acpi_lock_ac_dir(void);
extern void *acpi_unlock_ac_dir(struct proc_dir_entry *acpi_ac_dir);
static int acpi_ac_open_fs(struct inode *inode, struct file *file);
#define to_acpi_ac(x) container_of(x, struct acpi_ac, charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
static const struct file_operations acpi_ac_fops = {
.open = acpi_ac_open_fs,
.read = seq_read,
return 0;
}
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
/* --------------------------------------------------------------------------
FS Interface (/proc)
-------------------------------------------------------------------------- */
if (result)
goto end;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_ac_add_fs(device);
#endif
if (result)
end:
if (result) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_remove_fs(device);
#endif
kfree(ac);
ACPI_ALL_NOTIFY, acpi_ac_notify);
if (ac->charger.dev)
power_supply_unregister(&ac->charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_remove_fs(device);
#endif
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_dir = acpi_lock_ac_dir();
if (!acpi_ac_dir)
return -ENODEV;
result = acpi_bus_register_driver(&acpi_ac_driver);
if (result < 0) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_ac_dir(acpi_ac_dir);
#endif
return -ENODEV;
acpi_bus_unregister_driver(&acpi_ac_driver);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_ac_dir(acpi_ac_dir);
#endif
#include <linux/types.h>
#include <linux/jiffies.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <asm/uaccess.h>
module_param(cache_time, uint, 0644);
MODULE_PARM_DESC(cache_time, "cache time in milliseconds");
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
extern struct proc_dir_entry *acpi_lock_battery_dir(void);
extern void *acpi_unlock_battery_dir(struct proc_dir_entry *acpi_battery_dir);
val->intval = POWER_SUPPLY_STATUS_CHARGING;
else if (battery->state == 0)
val->intval = POWER_SUPPLY_STATUS_FULL;
+ else
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
break;
case POWER_SUPPLY_PROP_PRESENT:
val->intval = acpi_battery_present(battery);
POWER_SUPPLY_PROP_MANUFACTURER,
};
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
inline char *acpi_battery_units(struct acpi_battery *battery)
{
return (battery->power_unit)?"mA":"mW";
FS Interface (/proc)
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
static struct proc_dir_entry *acpi_battery_dir;
static int acpi_battery_print_info(struct seq_file *seq, int result)
acpi_driver_data(device) = battery;
mutex_init(&battery->lock);
acpi_battery_update(battery);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_battery_add_fs(device);
if (result)
goto end;
device->status.battery_present ? "present" : "absent");
end:
if (result) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_remove_fs(device);
#endif
kfree(battery);
status = acpi_remove_notify_handler(device->handle,
ACPI_ALL_NOTIFY,
acpi_battery_notify);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_remove_fs(device);
#endif
sysfs_remove_battery(battery);
{
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_dir = acpi_lock_battery_dir();
if (!acpi_battery_dir)
return -ENODEV;
#endif
if (acpi_bus_register_driver(&acpi_battery_driver) < 0) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_battery_dir(acpi_battery_dir);
#endif
return -ENODEV;
static void __exit acpi_battery_exit(void)
{
acpi_bus_unregister_driver(&acpi_battery_driver);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_battery_dir(acpi_battery_dir);
#endif
}
#undef PREFIX
#define PREFIX "ACPI: EC: "
+/* Uncomment next line to get verbose print outs*/
+/* #define DEBUG */
+
/* EC status register */
#define ACPI_EC_FLAG_OBF 0x01 /* Output buffer full */
#define ACPI_EC_FLAG_IBF 0x02 /* Input buffer full */
EC_FLAGS_WAIT_GPE = 0, /* Don't check status until GPE arrives */
EC_FLAGS_QUERY_PENDING, /* Query is pending */
EC_FLAGS_GPE_MODE, /* Expect GPE to be sent for status change */
- EC_FLAGS_ONLY_IBF_GPE, /* Expect GPE only for IBF = 0 event */
+ EC_FLAGS_NO_ADDRESS_GPE, /* Expect GPE only for non-address event */
+ EC_FLAGS_ADDRESS, /* Address is being written */
+ EC_FLAGS_NO_WDATA_GPE, /* Don't expect WDATA GPE event */
+ EC_FLAGS_WDATA, /* Data is being written */
};
static int acpi_ec_remove(struct acpi_device *device, int type);
static inline u8 acpi_ec_read_status(struct acpi_ec *ec)
{
- return inb(ec->command_addr);
+ u8 x = inb(ec->command_addr);
+ pr_debug(PREFIX "---> status = 0x%2x\n", x);
+ return x;
}
static inline u8 acpi_ec_read_data(struct acpi_ec *ec)
{
+ u8 x = inb(ec->data_addr);
+ pr_debug(PREFIX "---> data = 0x%2x\n", x);
return inb(ec->data_addr);
}
static inline void acpi_ec_write_cmd(struct acpi_ec *ec, u8 command)
{
+ pr_debug(PREFIX "<--- command = 0x%2x\n", command);
outb(command, ec->command_addr);
}
static inline void acpi_ec_write_data(struct acpi_ec *ec, u8 data)
{
+ pr_debug(PREFIX "<--- data = 0x%2x\n", data);
outb(data, ec->data_addr);
}
static int acpi_ec_wait(struct acpi_ec *ec, enum ec_event event, int force_poll)
{
+ int ret = 0;
+ if (unlikely(test_bit(EC_FLAGS_ADDRESS, &ec->flags) &&
+ test_bit(EC_FLAGS_NO_ADDRESS_GPE, &ec->flags)))
+ force_poll = 1;
+ if (unlikely(test_bit(EC_FLAGS_WDATA, &ec->flags) &&
+ test_bit(EC_FLAGS_NO_WDATA_GPE, &ec->flags)))
+ force_poll = 1;
if (likely(test_bit(EC_FLAGS_GPE_MODE, &ec->flags)) &&
likely(!force_poll)) {
if (wait_event_timeout(ec->wait, acpi_ec_check_status(ec, event),
msecs_to_jiffies(ACPI_EC_DELAY)))
- return 0;
+ goto end;
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
if (acpi_ec_check_status(ec, event)) {
- if (event == ACPI_EC_EVENT_OBF_1) {
- /* miss OBF = 1 GPE, don't expect it anymore */
- printk(KERN_INFO PREFIX "missing OBF_1 confirmation,"
- "switching to degraded mode.\n");
- set_bit(EC_FLAGS_ONLY_IBF_GPE, &ec->flags);
+ if (test_bit(EC_FLAGS_ADDRESS, &ec->flags)) {
+ /* miss address GPE, don't expect it anymore */
+ pr_info(PREFIX "missing address confirmation, "
+ "don't expect it any longer.\n");
+ set_bit(EC_FLAGS_NO_ADDRESS_GPE, &ec->flags);
+ } else if (test_bit(EC_FLAGS_WDATA, &ec->flags)) {
+ /* miss write data GPE, don't expect it */
+ pr_info(PREFIX "missing write data confirmation, "
+ "don't expect it any longer.\n");
+ set_bit(EC_FLAGS_NO_WDATA_GPE, &ec->flags);
} else {
/* missing GPEs, switch back to poll mode */
- printk(KERN_INFO PREFIX "missing IBF_1 confirmations,"
- "switch off interrupt mode.\n");
+ if (printk_ratelimit())
+ pr_info(PREFIX "missing confirmations, "
+ "switch off interrupt mode.\n");
clear_bit(EC_FLAGS_GPE_MODE, &ec->flags);
}
- return 0;
+ goto end;
}
} else {
unsigned long delay = jiffies + msecs_to_jiffies(ACPI_EC_DELAY);
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
while (time_before(jiffies, delay)) {
if (acpi_ec_check_status(ec, event))
- return 0;
+ goto end;
}
}
- printk(KERN_ERR PREFIX "acpi_ec_wait timeout,"
+ pr_err(PREFIX "acpi_ec_wait timeout,"
" status = %d, expect_event = %d\n",
acpi_ec_read_status(ec), event);
- return -ETIME;
+ ret = -ETIME;
+ end:
+ clear_bit(EC_FLAGS_ADDRESS, &ec->flags);
+ return ret;
}
static int acpi_ec_transaction_unlocked(struct acpi_ec *ec, u8 command,
int result = 0;
set_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
acpi_ec_write_cmd(ec, command);
-
+ pr_debug(PREFIX "transaction start\n");
for (; wdata_len > 0; --wdata_len) {
result = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, force_poll);
if (result) {
- printk(KERN_ERR PREFIX
+ pr_err(PREFIX
"write_cmd timeout, command = %d\n", command);
goto end;
}
+ /* mark the address byte written to EC */
+ if (rdata_len + wdata_len > 1)
+ set_bit(EC_FLAGS_ADDRESS, &ec->flags);
set_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
acpi_ec_write_data(ec, *(wdata++));
}
if (!rdata_len) {
+ set_bit(EC_FLAGS_WDATA, &ec->flags);
result = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, force_poll);
if (result) {
- printk(KERN_ERR PREFIX
+ pr_err(PREFIX
"finish-write timeout, command = %d\n", command);
goto end;
}
clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
for (; rdata_len > 0; --rdata_len) {
- if (test_bit(EC_FLAGS_ONLY_IBF_GPE, &ec->flags))
- force_poll = 1;
result = acpi_ec_wait(ec, ACPI_EC_EVENT_OBF_1, force_poll);
if (result) {
- printk(KERN_ERR PREFIX "read timeout, command = %d\n",
- command);
+ pr_err(PREFIX "read timeout, command = %d\n", command);
goto end;
}
/* Don't expect GPE after last read */
*(rdata++) = acpi_ec_read_data(ec);
}
end:
+ pr_debug(PREFIX "transaction end\n");
return result;
}
status = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, 0);
if (status) {
- printk(KERN_ERR PREFIX
- "input buffer is not empty, aborting transaction\n");
+ pr_err(PREFIX "input buffer is not empty, "
+ "aborting transaction\n");
goto end;
}
acpi_status status = AE_OK;
struct acpi_ec *ec = data;
+ pr_debug(PREFIX "~~~> interrupt\n");
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
if (test_bit(EC_FLAGS_GPE_MODE, &ec->flags))
wake_up(&ec->wait);
acpi_ec_gpe_query, ec);
} else if (unlikely(!test_bit(EC_FLAGS_GPE_MODE, &ec->flags))) {
/* this is non-query, must be confirmation */
- printk(KERN_INFO PREFIX "non-query interrupt received,"
- " switching to interrupt mode\n");
+ if (printk_ratelimit())
+ pr_info(PREFIX "non-query interrupt received,"
+ " switching to interrupt mode\n");
set_bit(EC_FLAGS_GPE_MODE, &ec->flags);
}
{
if (ACPI_FAILURE(acpi_remove_address_space_handler(ec->handle,
ACPI_ADR_SPACE_EC, &acpi_ec_space_handler)))
- printk(KERN_ERR PREFIX "failed to remove space handler\n");
+ pr_err(PREFIX "failed to remove space handler\n");
if (ACPI_FAILURE(acpi_remove_gpe_handler(NULL, ec->gpe,
&acpi_ec_gpe_handler)))
- printk(KERN_ERR PREFIX "failed to remove gpe handler\n");
+ pr_err(PREFIX "failed to remove gpe handler\n");
ec->handlers_installed = 0;
}
first_ec = ec;
acpi_driver_data(device) = ec;
acpi_ec_add_fs(device);
- printk(KERN_INFO PREFIX "GPE = 0x%lx, I/O: command/status = 0x%lx, data = 0x%lx\n",
+ pr_info(PREFIX "GPE = 0x%lx, I/O: command/status = 0x%lx, data = 0x%lx\n",
ec->gpe, ec->command_addr, ec->data_addr);
- printk(KERN_INFO PREFIX "driver started in %s mode\n",
+ pr_info(PREFIX "driver started in %s mode\n",
(test_bit(EC_FLAGS_GPE_MODE, &ec->flags))?"interrupt":"poll");
return 0;
}
status = acpi_get_table(ACPI_SIG_ECDT, 1,
(struct acpi_table_header **)&ecdt_ptr);
if (ACPI_SUCCESS(status)) {
- printk(KERN_INFO PREFIX "EC description table is found, configuring boot EC\n");
+ pr_info(PREFIX "EC description table is found, configuring boot EC\n");
boot_ec->command_addr = ecdt_ptr->control.address;
boot_ec->data_addr = ecdt_ptr->data.address;
boot_ec->gpe = ecdt_ptr->gpe;
boot_ec->handle = ACPI_ROOT_OBJECT;
} else {
+ /* This workaround is needed only on some broken machines,
+ * which require early EC, but fail to provide ECDT */
+ acpi_handle x;
printk(KERN_DEBUG PREFIX "Look up EC in DSDT\n");
status = acpi_get_devices(ec_device_ids[0].id, ec_parse_device,
boot_ec, NULL);
/* Check that acpi_get_devices actually find something */
if (ACPI_FAILURE(status) || !boot_ec->handle)
goto error;
+ /* We really need to limit this workaround, the only ASUS,
+ * which needs it, has fake EC._INI method, so use it as flag.
+ */
+ if (ACPI_FAILURE(acpi_get_handle(boot_ec->handle, "_INI", &x)))
+ goto error;
}
ret = ec_install_handlers(boot_ec);
if (!value)
value = &dummy;
- switch (width) {
- case 8:
+ *value = 0;
+ if (width <= 8) {
*(u8 *) value = inb(port);
- break;
- case 16:
+ } else if (width <= 16) {
*(u16 *) value = inw(port);
- break;
- case 32:
+ } else if (width <= 32) {
*(u32 *) value = inl(port);
- break;
- default:
+ } else {
BUG();
}
acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
{
- switch (width) {
- case 8:
+ if (width <= 8) {
outb(value, port);
- break;
- case 16:
+ } else if (width <= 16) {
outw(value, port);
- break;
- case 32:
+ } else if (width <= 32) {
outl(value, port);
- break;
- default:
+ } else {
BUG();
}
request_region(pr->throttling.address, 6, "ACPI CPU throttle");
}
-#ifdef CONFIG_CPU_FREQ
- acpi_processor_ppc_has_changed(pr);
-#endif
- acpi_processor_get_throttling_info(pr);
- acpi_processor_get_limit_info(pr);
-
return 0;
}
*/
if (processor_device_array[pr->id] != NULL &&
processor_device_array[pr->id] != device) {
- printk(KERN_WARNING "BIOS reported wrong ACPI id"
+ printk(KERN_WARNING "BIOS reported wrong ACPI id "
"for the processor\n");
return -ENODEV;
}
/* _PDC call should be done before doing anything else (if reqd.). */
arch_acpi_processor_init_pdc(pr);
acpi_processor_set_pdc(pr);
+#ifdef CONFIG_CPU_FREQ
+ acpi_processor_ppc_has_changed(pr);
+#endif
+ acpi_processor_get_throttling_info(pr);
+ acpi_processor_get_limit_info(pr);
+
acpi_processor_power_init(pr, device);
{
struct acpi_processor *pr = data;
struct acpi_device *device = NULL;
-
+ int saved;
if (!pr)
return;
switch (event) {
case ACPI_PROCESSOR_NOTIFY_PERFORMANCE:
+ saved = pr->performance_platform_limit;
acpi_processor_ppc_has_changed(pr);
+ if (saved == pr->performance_platform_limit)
+ break;
acpi_bus_generate_proc_event(device, event,
pr->performance_platform_limit);
acpi_bus_generate_netlink_event(device->pnp.device_class,
return PM_TIMER_TICKS_TO_US((0xFFFFFFFF - t1) + t2);
}
+static void acpi_safe_halt(void)
+{
+ current_thread_info()->status &= ~TS_POLLING;
+ /*
+ * TS_POLLING-cleared state must be visible before we
+ * test NEED_RESCHED:
+ */
+ smp_mb();
+ if (!need_resched())
+ safe_halt();
+ current_thread_info()->status |= TS_POLLING;
+}
+
#ifndef CONFIG_CPU_IDLE
static void
return;
}
-static void acpi_safe_halt(void)
-{
- current_thread_info()->status &= ~TS_POLLING;
- /*
- * TS_POLLING-cleared state must be visible before we
- * test NEED_RESCHED:
- */
- smp_mb();
- if (!need_resched())
- safe_halt();
- current_thread_info()->status |= TS_POLLING;
-}
-
static atomic_t c3_cpu_count;
/* Common C-state entry for C2, C3, .. */
if (pr->flags.bm_check)
acpi_idle_update_bm_rld(pr, cx);
- current_thread_info()->status &= ~TS_POLLING;
- /*
- * TS_POLLING-cleared state must be visible before we test
- * NEED_RESCHED:
- */
- smp_mb();
- if (!need_resched())
- safe_halt();
- current_thread_info()->status |= TS_POLLING;
+ acpi_safe_halt();
cx->usage++;
struct acpi_processor *pr;
struct acpi_processor_cx *cx = cpuidle_get_statedata(state);
u32 t1, t2;
+ int sleep_ticks = 0;
+
pr = processors[smp_processor_id()];
if (unlikely(!pr))
ACPI_FLUSH_CPU_CACHE();
t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ /* Tell the scheduler that we are going deep-idle: */
+ sched_clock_idle_sleep_event();
acpi_state_timer_broadcast(pr, cx, 1);
acpi_idle_do_entry(cx);
t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
/* TSC could halt in idle, so notify users */
mark_tsc_unstable("TSC halts in idle");;
#endif
+ sleep_ticks = ticks_elapsed(t1, t2);
+
+ /* Tell the scheduler how much we idled: */
+ sched_clock_idle_wakeup_event(sleep_ticks*PM_TIMER_TICK_NS);
local_irq_enable();
current_thread_info()->status |= TS_POLLING;
cx->usage++;
acpi_state_timer_broadcast(pr, cx, 0);
- cx->time += ticks_elapsed(t1, t2);
+ cx->time += sleep_ticks;
return ticks_elapsed_in_us(t1, t2);
}
struct acpi_processor *pr;
struct acpi_processor_cx *cx = cpuidle_get_statedata(state);
u32 t1, t2;
+ int sleep_ticks = 0;
+
pr = processors[smp_processor_id()];
if (unlikely(!pr))
if (acpi_idle_suspend)
return(acpi_idle_enter_c1(dev, state));
+ if (acpi_idle_bm_check()) {
+ if (dev->safe_state) {
+ return dev->safe_state->enter(dev, dev->safe_state);
+ } else {
+ acpi_safe_halt();
+ return 0;
+ }
+ }
+
local_irq_disable();
current_thread_info()->status &= ~TS_POLLING;
/*
return 0;
}
+ /* Tell the scheduler that we are going deep-idle: */
+ sched_clock_idle_sleep_event();
/*
* Must be done before busmaster disable as we might need to
* access HPET !
*/
acpi_state_timer_broadcast(pr, cx, 1);
- if (acpi_idle_bm_check()) {
- cx = pr->power.bm_state;
-
- acpi_idle_update_bm_rld(pr, cx);
-
- t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- acpi_idle_do_entry(cx);
- t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- } else {
- acpi_idle_update_bm_rld(pr, cx);
+ acpi_idle_update_bm_rld(pr, cx);
+ /*
+ * disable bus master
+ * bm_check implies we need ARB_DIS
+ * !bm_check implies we need cache flush
+ * bm_control implies whether we can do ARB_DIS
+ *
+ * That leaves a case where bm_check is set and bm_control is
+ * not set. In that case we cannot do much, we enter C3
+ * without doing anything.
+ */
+ if (pr->flags.bm_check && pr->flags.bm_control) {
spin_lock(&c3_lock);
c3_cpu_count++;
/* Disable bus master arbitration when all CPUs are in C3 */
if (c3_cpu_count == num_online_cpus())
acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1);
spin_unlock(&c3_lock);
+ } else if (!pr->flags.bm_check) {
+ ACPI_FLUSH_CPU_CACHE();
+ }
- t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- acpi_idle_do_entry(cx);
- t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ acpi_idle_do_entry(cx);
+ t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ /* Re-enable bus master arbitration */
+ if (pr->flags.bm_check && pr->flags.bm_control) {
spin_lock(&c3_lock);
- /* Re-enable bus master arbitration */
- if (c3_cpu_count == num_online_cpus())
- acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0);
+ acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0);
c3_cpu_count--;
spin_unlock(&c3_lock);
}
/* TSC could halt in idle, so notify users */
mark_tsc_unstable("TSC halts in idle");
#endif
+ sleep_ticks = ticks_elapsed(t1, t2);
+ /* Tell the scheduler how much we idled: */
+ sched_clock_idle_wakeup_event(sleep_ticks*PM_TIMER_TICK_NS);
local_irq_enable();
current_thread_info()->status |= TS_POLLING;
cx->usage++;
acpi_state_timer_broadcast(pr, cx, 0);
- cx->time += ticks_elapsed(t1, t2);
+ cx->time += sleep_ticks;
return ticks_elapsed_in_us(t1, t2);
}
case ACPI_STATE_C1:
state->flags |= CPUIDLE_FLAG_SHALLOW;
state->enter = acpi_idle_enter_c1;
+ dev->safe_state = state;
break;
case ACPI_STATE_C2:
state->flags |= CPUIDLE_FLAG_BALANCED;
state->flags |= CPUIDLE_FLAG_TIME_VALID;
state->enter = acpi_idle_enter_simple;
+ dev->safe_state = state;
break;
case ACPI_STATE_C3:
if (!count)
return -EINVAL;
- /* find the deepest state that can handle active BM */
- if (pr->flags.bm_check) {
- for (i = 1; i < ACPI_PROCESSOR_MAX_POWER && i <= max_cstate; i++)
- if (pr->power.states[i].type == ACPI_STATE_C3)
- break;
- pr->power.bm_state = &pr->power.states[i-1];
- }
-
return 0;
}
if (!first_run) {
dmi_check_system(processor_power_dmi_table);
+ max_cstate = acpi_processor_cstate_check(max_cstate);
if (max_cstate < ACPI_C_STATES_MAX)
printk(KERN_NOTICE
"ACPI: processor limited to max C-state %d\n",
int acpi_processor_tstate_has_changed(struct acpi_processor *pr)
{
- return acpi_processor_get_platform_limit(pr);
+ int result = 0;
+ int throttling_limit;
+ int current_state;
+ struct acpi_processor_limit *limit;
+ int target_state;
+
+ result = acpi_processor_get_platform_limit(pr);
+ if (result) {
+ /* Throttling Limit is unsupported */
+ return result;
+ }
+
+ throttling_limit = pr->throttling_platform_limit;
+ if (throttling_limit >= pr->throttling.state_count) {
+ /* Uncorrect Throttling Limit */
+ return -EINVAL;
+ }
+
+ current_state = pr->throttling.state;
+ if (current_state > throttling_limit) {
+ /*
+ * The current state can meet the requirement of
+ * _TPC limit. But it is reasonable that OSPM changes
+ * t-states from high to low for better performance.
+ * Of course the limit condition of thermal
+ * and user should be considered.
+ */
+ limit = &pr->limit;
+ target_state = throttling_limit;
+ if (limit->thermal.tx > target_state)
+ target_state = limit->thermal.tx;
+ if (limit->user.tx > target_state)
+ target_state = limit->user.tx;
+ } else if (current_state == throttling_limit) {
+ /*
+ * Unnecessary to change the throttling state
+ */
+ return 0;
+ } else {
+ /*
+ * If the current state is lower than the limit of _TPC, it
+ * will be forced to switch to the throttling state defined
+ * by throttling_platfor_limit.
+ * Because the previous state meets with the limit condition
+ * of thermal and user, it is unnecessary to check it again.
+ */
+ target_state = throttling_limit;
+ }
+ return acpi_processor_set_throttling(pr, target_state);
}
/*
struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
union acpi_object *ptc = NULL;
union acpi_object obj = { 0 };
+ struct acpi_processor_throttling *throttling;
status = acpi_evaluate_object(pr->handle, "_PTC", NULL, &buffer);
if (ACPI_FAILURE(status)) {
memcpy(&pr->throttling.status_register, obj.buffer.pointer,
sizeof(struct acpi_ptc_register));
+ throttling = &pr->throttling;
+
+ if ((throttling->control_register.bit_width +
+ throttling->control_register.bit_offset) > 32) {
+ printk(KERN_ERR PREFIX "Invalid _PTC control register\n");
+ result = -EFAULT;
+ goto end;
+ }
+
+ if ((throttling->status_register.bit_width +
+ throttling->status_register.bit_offset) > 32) {
+ printk(KERN_ERR PREFIX "Invalid _PTC status register\n");
+ result = -EFAULT;
+ goto end;
+ }
+
end:
kfree(buffer.pointer);
return 0;
}
-static int acpi_read_throttling_status(struct acpi_processor_throttling
- *throttling)
+#ifdef CONFIG_X86
+static int acpi_throttling_rdmsr(struct acpi_processor *pr,
+ acpi_integer * value)
{
- int value = -1;
+ struct cpuinfo_x86 *c;
+ u64 msr_high, msr_low;
+ unsigned int cpu;
+ u64 msr = 0;
+ int ret = -1;
+
+ cpu = pr->id;
+ c = &cpu_data(cpu);
+
+ if ((c->x86_vendor != X86_VENDOR_INTEL) ||
+ !cpu_has(c, X86_FEATURE_ACPI)) {
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ } else {
+ msr_low = 0;
+ msr_high = 0;
+ rdmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL,
+ (u32 *)&msr_low , (u32 *) &msr_high);
+ msr = (msr_high << 32) | msr_low;
+ *value = (acpi_integer) msr;
+ ret = 0;
+ }
+ return ret;
+}
+
+static int acpi_throttling_wrmsr(struct acpi_processor *pr, acpi_integer value)
+{
+ struct cpuinfo_x86 *c;
+ unsigned int cpu;
+ int ret = -1;
+ u64 msr;
+
+ cpu = pr->id;
+ c = &cpu_data(cpu);
+
+ if ((c->x86_vendor != X86_VENDOR_INTEL) ||
+ !cpu_has(c, X86_FEATURE_ACPI)) {
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ } else {
+ msr = value;
+ wrmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL,
+ msr & 0xffffffff, msr >> 32);
+ ret = 0;
+ }
+ return ret;
+}
+#else
+static int acpi_throttling_rdmsr(struct acpi_processor *pr,
+ acpi_integer * value)
+{
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ return -1;
+}
+
+static int acpi_throttling_wrmsr(struct acpi_processor *pr, acpi_integer value)
+{
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ return -1;
+}
+#endif
+
+static int acpi_read_throttling_status(struct acpi_processor *pr,
+ acpi_integer *value)
+{
+ u32 bit_width, bit_offset;
+ u64 ptc_value;
+ u64 ptc_mask;
+ struct acpi_processor_throttling *throttling;
+ int ret = -1;
+
+ throttling = &pr->throttling;
switch (throttling->status_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
+ ptc_value = 0;
+ bit_width = throttling->status_register.bit_width;
+ bit_offset = throttling->status_register.bit_offset;
+
acpi_os_read_port((acpi_io_address) throttling->status_register.
- address, &value,
- (u32) throttling->status_register.bit_width *
- 8);
+ address, (u32 *) &ptc_value,
+ (u32) (bit_width + bit_offset));
+ ptc_mask = (1 << bit_width) - 1;
+ *value = (acpi_integer) ((ptc_value >> bit_offset) & ptc_mask);
+ ret = 0;
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
- printk(KERN_ERR PREFIX
- "HARDWARE addr space,NOT supported yet\n");
+ ret = acpi_throttling_rdmsr(pr, value);
break;
default:
printk(KERN_ERR PREFIX "Unknown addr space %d\n",
(u32) (throttling->status_register.space_id));
}
- return value;
+ return ret;
}
-static int acpi_write_throttling_state(struct acpi_processor_throttling
- *throttling, int value)
+static int acpi_write_throttling_state(struct acpi_processor *pr,
+ acpi_integer value)
{
+ u32 bit_width, bit_offset;
+ u64 ptc_value;
+ u64 ptc_mask;
+ struct acpi_processor_throttling *throttling;
int ret = -1;
+ throttling = &pr->throttling;
switch (throttling->control_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
+ bit_width = throttling->control_register.bit_width;
+ bit_offset = throttling->control_register.bit_offset;
+ ptc_mask = (1 << bit_width) - 1;
+ ptc_value = value & ptc_mask;
+
acpi_os_write_port((acpi_io_address) throttling->
- control_register.address, value,
- (u32) throttling->control_register.
- bit_width * 8);
+ control_register.address,
+ (u32) (ptc_value << bit_offset),
+ (u32) (bit_width + bit_offset));
ret = 0;
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
- printk(KERN_ERR PREFIX
- "HARDWARE addr space,NOT supported yet\n");
+ ret = acpi_throttling_wrmsr(pr, value);
break;
default:
printk(KERN_ERR PREFIX "Unknown addr space %d\n",
return ret;
}
-static int acpi_get_throttling_state(struct acpi_processor *pr, int value)
+static int acpi_get_throttling_state(struct acpi_processor *pr,
+ acpi_integer value)
{
int i;
return i;
}
-static int acpi_get_throttling_value(struct acpi_processor *pr, int state)
+static int acpi_get_throttling_value(struct acpi_processor *pr,
+ int state, acpi_integer *value)
{
- int value = -1;
+ int ret = -1;
+
if (state >= 0 && state <= pr->throttling.state_count) {
struct acpi_processor_tx_tss *tx =
(struct acpi_processor_tx_tss *)&(pr->throttling.
states_tss[state]);
- value = tx->control;
+ *value = tx->control;
+ ret = 0;
}
- return value;
+ return ret;
}
static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr)
{
int state = 0;
- u32 value = 0;
+ int ret;
+ acpi_integer value;
if (!pr)
return -EINVAL;
pr->throttling.state = 0;
local_irq_disable();
- value = acpi_read_throttling_status(&pr->throttling);
- if (value >= 0) {
+ value = 0;
+ ret = acpi_read_throttling_status(pr, &value);
+ if (ret >= 0) {
state = acpi_get_throttling_state(pr, value);
pr->throttling.state = state;
}
return pr->throttling.acpi_processor_get_throttling(pr);
}
+static int acpi_processor_get_fadt_info(struct acpi_processor *pr)
+{
+ int i, step;
+
+ if (!pr->throttling.address) {
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling register\n"));
+ return -EINVAL;
+ } else if (!pr->throttling.duty_width) {
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling states\n"));
+ return -EINVAL;
+ }
+ /* TBD: Support duty_cycle values that span bit 4. */
+ else if ((pr->throttling.duty_offset + pr->throttling.duty_width) > 4) {
+ printk(KERN_WARNING PREFIX "duty_cycle spans bit 4\n");
+ return -EINVAL;
+ }
+
+ pr->throttling.state_count = 1 << acpi_gbl_FADT.duty_width;
+
+ /*
+ * Compute state values. Note that throttling displays a linear power
+ * performance relationship (at 50% performance the CPU will consume
+ * 50% power). Values are in 1/10th of a percent to preserve accuracy.
+ */
+
+ step = (1000 / pr->throttling.state_count);
+
+ for (i = 0; i < pr->throttling.state_count; i++) {
+ pr->throttling.states[i].performance = 1000 - step * i;
+ pr->throttling.states[i].power = 1000 - step * i;
+ }
+ return 0;
+}
+
static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr,
int state)
{
static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr,
int state)
{
- u32 value = 0;
+ int ret;
+ acpi_integer value;
if (!pr)
return -EINVAL;
return -EPERM;
local_irq_disable();
-
- value = acpi_get_throttling_value(pr, state);
- if (value >= 0) {
- acpi_write_throttling_state(&pr->throttling, value);
+ value = 0;
+ ret = acpi_get_throttling_value(pr, state, &value);
+ if (ret >= 0) {
+ acpi_write_throttling_state(pr, value);
pr->throttling.state = state;
}
local_irq_enable();
int acpi_processor_get_throttling_info(struct acpi_processor *pr)
{
int result = 0;
- int step = 0;
- int i = 0;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"pblk_address[0x%08x] duty_offset[%d] duty_width[%d]\n",
acpi_processor_get_throttling_states(pr) ||
acpi_processor_get_platform_limit(pr))
{
+ if (acpi_processor_get_fadt_info(pr))
+ return 0;
pr->throttling.acpi_processor_get_throttling =
&acpi_processor_get_throttling_fadt;
pr->throttling.acpi_processor_set_throttling =
acpi_processor_get_tsd(pr);
- if (!pr->throttling.address) {
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling register\n"));
- return 0;
- } else if (!pr->throttling.duty_width) {
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling states\n"));
- return 0;
- }
- /* TBD: Support duty_cycle values that span bit 4. */
- else if ((pr->throttling.duty_offset + pr->throttling.duty_width) > 4) {
- printk(KERN_WARNING PREFIX "duty_cycle spans bit 4\n");
- return 0;
- }
-
/*
* PIIX4 Errata: We don't support throttling on the original PIIX4.
* This shouldn't be an issue as few (if any) mobile systems ever
return 0;
}
- pr->throttling.state_count = 1 << acpi_gbl_FADT.duty_width;
-
- /*
- * Compute state values. Note that throttling displays a linear power/
- * performance relationship (at 50% performance the CPU will consume
- * 50% power). Values are in 1/10th of a percent to preserve accuracy.
- */
-
- step = (1000 / pr->throttling.state_count);
-
- for (i = 0; i < pr->throttling.state_count; i++) {
- pr->throttling.states[i].performance = step * i;
- pr->throttling.states[i].power = step * i;
- }
-
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Found %d throttling states\n",
pr->throttling.state_count));
#include <linux/moduleparam.h>
#include <linux/kernel.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <asm/uaccess.h>
struct acpi_battery {
struct power_supply bat;
struct acpi_sbs *sbs;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
struct proc_dir_entry *proc_entry;
#endif
unsigned long update_time;
u16 spec;
u8 id;
u8 present:1;
+ u8 have_sysfs_alarm:1;
};
#define to_acpi_battery(x) container_of(x, struct acpi_battery, bat);
struct acpi_device *device;
struct acpi_smb_hc *hc;
struct mutex lock;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
struct proc_dir_entry *charger_entry;
#endif
struct acpi_battery battery[MAX_SBS_BAT];
FS Interface (/proc/acpi)
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
/* Generic Routines */
static int
acpi_sbs_add_fs(struct proc_dir_entry **dir,
return result;
sprintf(battery->name, ACPI_BATTERY_DIR_NAME, id);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_sbs_add_fs(&battery->proc_entry, acpi_battery_dir,
battery->name, &acpi_battery_info_fops,
&acpi_battery_state_fops, &acpi_battery_alarm_fops,
}
battery->bat.get_property = acpi_sbs_battery_get_property;
result = power_supply_register(&sbs->device->dev, &battery->bat);
- device_create_file(battery->bat.dev, &alarm_attr);
+ if (result)
+ goto end;
+ result = device_create_file(battery->bat.dev, &alarm_attr);
+ if (result)
+ goto end;
+ battery->have_sysfs_alarm = 1;
+ end:
printk(KERN_INFO PREFIX "%s [%s]: Battery Slot [%s] (battery %s)\n",
ACPI_SBS_DEVICE_NAME, acpi_device_bid(sbs->device),
battery->name, sbs->battery->present ? "present" : "absent");
static void acpi_battery_remove(struct acpi_sbs *sbs, int id)
{
- if (sbs->battery[id].bat.dev)
- device_remove_file(sbs->battery[id].bat.dev, &alarm_attr);
- power_supply_unregister(&sbs->battery[id].bat);
-#ifdef CONFIG_ACPI_PROCFS
- if (sbs->battery[id].proc_entry) {
- acpi_sbs_remove_fs(&(sbs->battery[id].proc_entry),
- acpi_battery_dir);
+ struct acpi_battery *battery = &sbs->battery[id];
+
+ if (battery->bat.dev) {
+ if (battery->have_sysfs_alarm)
+ device_remove_file(battery->bat.dev, &alarm_attr);
+ power_supply_unregister(&battery->bat);
}
+#ifdef CONFIG_ACPI_PROCFS_POWER
+ if (battery->proc_entry)
+ acpi_sbs_remove_fs(&battery->proc_entry, acpi_battery_dir);
#endif
}
result = acpi_ac_get_present(sbs);
if (result)
goto end;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_sbs_add_fs(&sbs->charger_entry, acpi_ac_dir,
ACPI_AC_DIR_NAME, NULL,
&acpi_ac_state_fops, NULL, sbs);
{
if (sbs->charger.dev)
power_supply_unregister(&sbs->charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
if (sbs->charger_entry)
acpi_sbs_remove_fs(&sbs->charger_entry, acpi_ac_dir);
#endif
static void acpi_sbs_rmdirs(void)
{
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
if (acpi_ac_dir) {
acpi_unlock_ac_dir(acpi_ac_dir);
acpi_ac_dir = NULL;
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_dir = acpi_lock_ac_dir();
if (!acpi_ac_dir)
return -ENODEV;
/* XSDT has NULL entry, RSDT is used */
address = rsdt_address;
table_entry_size = sizeof(u32);
- ACPI_WARNING((AE_INFO, "BIOS XSDT has NULL entry,"
+ ACPI_WARNING((AE_INFO, "BIOS XSDT has NULL entry, "
"using RSDT"));
}
}
#include <linux/init.h>
#include <linux/types.h>
#include <linux/list.h>
+#include <linux/mutex.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <linux/input.h>
u8 attached_count;
struct acpi_video_bus_cap cap;
struct acpi_video_bus_flags flags;
- struct semaphore sem;
struct list_head video_device_list;
+ struct mutex device_list_lock; /* protects video_device_list */
struct proc_dir_entry *dir;
struct input_dev *input;
char phys[32]; /* for input device */
{
struct seq_file *m = file->private_data;
struct acpi_video_device *dev = m->private;
- char str[4] = { 0 };
+ char str[5] = { 0 };
unsigned int level = 0;
int i;
return -ENODEV;
}
- down(&video->sem);
+ mutex_lock(&video->device_list_lock);
list_add_tail(&data->entry, &video->video_device_list);
- up(&video->sem);
+ mutex_unlock(&video->device_list_lock);
acpi_video_device_add_fs(device);
static void acpi_video_device_rebind(struct acpi_video_bus *video)
{
- struct list_head *node, *next;
- list_for_each_safe(node, next, &video->video_device_list) {
- struct acpi_video_device *dev =
- container_of(node, struct acpi_video_device, entry);
+ struct acpi_video_device *dev;
+
+ mutex_lock(&video->device_list_lock);
+
+ list_for_each_entry(dev, &video->video_device_list, entry)
acpi_video_device_bind(video, dev);
- }
+
+ mutex_unlock(&video->device_list_lock);
}
/*
static int acpi_video_switch_output(struct acpi_video_bus *video, int event)
{
- struct list_head *node, *next;
+ struct list_head *node;
struct acpi_video_device *dev = NULL;
struct acpi_video_device *dev_next = NULL;
struct acpi_video_device *dev_prev = NULL;
unsigned long state;
int status = 0;
+ mutex_lock(&video->device_list_lock);
- list_for_each_safe(node, next, &video->video_device_list) {
+ list_for_each(node, &video->video_device_list) {
dev = container_of(node, struct acpi_video_device, entry);
status = acpi_video_device_get_state(dev, &state);
if (state & 0x2) {
- dev_next =
- container_of(node->next, struct acpi_video_device,
- entry);
- dev_prev =
- container_of(node->prev, struct acpi_video_device,
- entry);
+ dev_next = container_of(node->next,
+ struct acpi_video_device, entry);
+ dev_prev = container_of(node->prev,
+ struct acpi_video_device, entry);
goto out;
}
}
+
dev_next = container_of(node->next, struct acpi_video_device, entry);
dev_prev = container_of(node->prev, struct acpi_video_device, entry);
- out:
+
+ out:
+ mutex_unlock(&video->device_list_lock);
+
switch (event) {
case ACPI_VIDEO_NOTIFY_CYCLE:
case ACPI_VIDEO_NOTIFY_NEXT_OUTPUT:
struct acpi_device *device)
{
int status = 0;
- struct list_head *node, *next;
-
+ struct acpi_device *dev;
acpi_video_device_enumerate(video);
- list_for_each_safe(node, next, &device->children) {
- struct acpi_device *dev =
- list_entry(node, struct acpi_device, node);
-
- if (!dev)
- continue;
+ list_for_each_entry(dev, &device->children, node) {
status = acpi_video_bus_get_one_device(dev, video);
if (ACPI_FAILURE(status)) {
ACPI_EXCEPTION((AE_INFO, status, "Cant attach device"));
continue;
}
-
}
return status;
}
video = device->video;
- down(&video->sem);
- list_del(&device->entry);
- up(&video->sem);
acpi_video_device_remove_fs(device->dev);
status = acpi_remove_notify_handler(device->dev->handle,
acpi_video_device_notify);
backlight_device_unregister(device->backlight);
video_output_unregister(device->output_dev);
+
return 0;
}
static int acpi_video_bus_put_devices(struct acpi_video_bus *video)
{
int status;
- struct list_head *node, *next;
+ struct acpi_video_device *dev, *next;
+ mutex_lock(&video->device_list_lock);
- list_for_each_safe(node, next, &video->video_device_list) {
- struct acpi_video_device *data =
- list_entry(node, struct acpi_video_device, entry);
- if (!data)
- continue;
+ list_for_each_entry_safe(dev, next, &video->video_device_list, entry) {
- status = acpi_video_bus_put_one_device(data);
+ status = acpi_video_bus_put_one_device(dev);
if (ACPI_FAILURE(status))
printk(KERN_WARNING PREFIX
"hhuuhhuu bug in acpi video driver.\n");
- if (data->brightness)
- kfree(data->brightness->levels);
- kfree(data->brightness);
- kfree(data);
+ if (dev->brightness) {
+ kfree(dev->brightness->levels);
+ kfree(dev->brightness);
+ }
+ list_del(&dev->entry);
+ kfree(dev);
}
+ mutex_unlock(&video->device_list_lock);
+
return 0;
}
struct input_dev *input;
int keycode;
-
- printk("video bus notify\n");
-
if (!video)
return;
static int instance;
static int acpi_video_bus_add(struct acpi_device *device)
{
- int result = 0;
- acpi_status status = 0;
- struct acpi_video_bus *video = NULL;
+ acpi_status status;
+ struct acpi_video_bus *video;
struct input_dev *input;
-
-
- if (!device)
- return -EINVAL;
+ int error;
video = kzalloc(sizeof(struct acpi_video_bus), GFP_KERNEL);
if (!video)
acpi_driver_data(device) = video;
acpi_video_bus_find_cap(video);
- result = acpi_video_bus_check(video);
- if (result)
- goto end;
+ error = acpi_video_bus_check(video);
+ if (error)
+ goto err_free_video;
- result = acpi_video_bus_add_fs(device);
- if (result)
- goto end;
+ error = acpi_video_bus_add_fs(device);
+ if (error)
+ goto err_free_video;
- init_MUTEX(&video->sem);
+ mutex_init(&video->device_list_lock);
INIT_LIST_HEAD(&video->video_device_list);
acpi_video_bus_get_devices(video, device);
if (ACPI_FAILURE(status)) {
ACPI_DEBUG_PRINT((ACPI_DB_ERROR,
"Error installing notify handler\n"));
- acpi_video_bus_stop_devices(video);
- acpi_video_bus_put_devices(video);
- kfree(video->attached_array);
- acpi_video_bus_remove_fs(device);
- result = -ENODEV;
- goto end;
+ error = -ENODEV;
+ goto err_stop_video;
}
-
video->input = input = input_allocate_device();
+ if (!input) {
+ error = -ENOMEM;
+ goto err_uninstall_notify;
+ }
snprintf(video->phys, sizeof(video->phys),
"%s/video/input0", acpi_device_hid(video->device));
input->phys = video->phys;
input->id.bustype = BUS_HOST;
input->id.product = 0x06;
+ input->dev.parent = &device->dev;
input->evbit[0] = BIT(EV_KEY);
set_bit(KEY_SWITCHVIDEOMODE, input->keybit);
set_bit(KEY_VIDEO_NEXT, input->keybit);
set_bit(KEY_BRIGHTNESS_ZERO, input->keybit);
set_bit(KEY_DISPLAY_OFF, input->keybit);
set_bit(KEY_UNKNOWN, input->keybit);
- result = input_register_device(input);
- if (result) {
- acpi_remove_notify_handler(video->device->handle,
- ACPI_DEVICE_NOTIFY,
- acpi_video_bus_notify);
- acpi_video_bus_stop_devices(video);
- acpi_video_bus_put_devices(video);
- kfree(video->attached_array);
- acpi_video_bus_remove_fs(device);
- goto end;
- }
+ error = input_register_device(input);
+ if (error)
+ goto err_free_input_dev;
printk(KERN_INFO PREFIX "%s [%s] (multi-head: %s rom: %s post: %s)\n",
ACPI_VIDEO_DEVICE_NAME, acpi_device_bid(device),
video->flags.rom ? "yes" : "no",
video->flags.post ? "yes" : "no");
- end:
- if (result)
- kfree(video);
+ return 0;
+
+ err_free_input_dev:
+ input_free_device(input);
+ err_uninstall_notify:
+ acpi_remove_notify_handler(device->handle, ACPI_DEVICE_NOTIFY,
+ acpi_video_bus_notify);
+ err_stop_video:
+ acpi_video_bus_stop_devices(video);
+ acpi_video_bus_put_devices(video);
+ kfree(video->attached_array);
+ acpi_video_bus_remove_fs(device);
+ err_free_video:
+ kfree(video);
+ acpi_driver_data(device) = NULL;
- return result;
+ return error;
}
static int acpi_video_bus_remove(struct acpi_device *device, int type)
PIIX_80C_SEC = (1 << 7) | (1 << 6),
/* controller IDs */
- piix_pata_33 = 0, /* PIIX4 at 33Mhz */
- ich_pata_33 = 1, /* ICH up to UDMA 33 only */
- ich_pata_66 = 2, /* ICH up to 66 Mhz */
- ich_pata_100 = 3, /* ICH up to UDMA 100 */
- ich5_sata = 5,
- ich6_sata = 6,
- ich6_sata_ahci = 7,
- ich6m_sata_ahci = 8,
- ich8_sata_ahci = 9,
- piix_pata_mwdma = 10, /* PIIX3 MWDMA only */
- tolapai_sata_ahci = 11,
- ich9_2port_sata = 12,
+ piix_pata_mwdma = 0, /* PIIX3 MWDMA only */
+ piix_pata_33, /* PIIX4 at 33Mhz */
+ ich_pata_33, /* ICH up to UDMA 33 only */
+ ich_pata_66, /* ICH up to 66 Mhz */
+ ich_pata_100, /* ICH up to UDMA 100 */
+ ich5_sata,
+ ich6_sata,
+ ich6_sata_ahci,
+ ich6m_sata_ahci,
+ ich8_sata_ahci,
+ ich8_2port_sata,
+ ich8m_apple_sata_ahci, /* locks up on second port enable */
+ tolapai_sata_ahci,
/* constants for mapping table */
P0 = 0, /* port 0 */
/* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller 2 IDE (ICH8) */
- { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* Mobile SATA Controller IDE (ICH8M), Apple */
+ { 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata_ahci },
/* SATA Controller IDE (ICH9) */
{ 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
{ 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (Tolapai) */
static const struct piix_map_db ich8_map_db = {
.mask = 0x3,
- .port_enable = 0x3,
+ .port_enable = 0xf,
.map = {
/* PM PS SM SS MAP */
{ P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
},
};
-static const struct piix_map_db tolapai_map_db = {
+static const struct piix_map_db ich8_2port_map_db = {
.mask = 0x3,
.port_enable = 0x3,
.map = {
},
};
-static const struct piix_map_db ich9_2port_map_db = {
+static const struct piix_map_db ich8m_apple_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x1,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, NA, NA }, /* 00b */
+ { RV, RV, RV, RV },
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db tolapai_map_db = {
.mask = 0x3,
.port_enable = 0x3,
.map = {
[ich6_sata_ahci] = &ich6_map_db,
[ich6m_sata_ahci] = &ich6m_map_db,
[ich8_sata_ahci] = &ich8_map_db,
+ [ich8_2port_sata] = &ich8_2port_map_db,
+ [ich8m_apple_sata_ahci] = &ich8m_apple_map_db,
[tolapai_sata_ahci] = &tolapai_map_db,
- [ich9_2port_sata] = &ich9_2port_map_db,
};
static struct ata_port_info piix_port_info[] = {
+ [piix_pata_mwdma] = /* PIIX3 MWDMA only */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .port_ops = &piix_pata_ops,
+ },
+
[piix_pata_33] = /* PIIX4 at 33MHz */
{
.sht = &piix_sht,
.port_ops = &piix_sata_ops,
},
- [piix_pata_mwdma] = /* PIIX3 MWDMA only */
+ [ich8_2port_sata] =
{
.sht = &piix_sht,
- .flags = PIIX_PATA_FLAGS,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
- .port_ops = &piix_pata_ops,
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &piix_sata_ops,
},
[tolapai_sata_ahci] =
.port_ops = &piix_sata_ops,
},
- [ich9_2port_sata] =
+ [ich8m_apple_sata_ahci] =
{
.sht = &piix_sht,
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
+
};
static struct pci_bits piix_enable_bits[] = {
DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
},
},
+ {
+ .ident = "SATELLITE U205",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U205"),
+ },
+ },
{
.ident = "Portege M500",
.matches = {
if (!mmio)
return -ENOMEM;
- tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
if (tmp & AHCI_ENABLE) {
tmp &= ~AHCI_ENABLE;
- writel(tmp, mmio + AHCI_GLOBAL_CTL);
+ iowrite32(tmp, mmio + AHCI_GLOBAL_CTL);
- tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
if (tmp & AHCI_ENABLE)
rc = -EIO;
}
* Hardware documentation available from http://www.t13.org/ and
* http://www.sata-io.org/
*
+ * Standards documents from:
+ * http://www.t13.org (ATA standards, PCI DMA IDE spec)
+ * http://www.t10.org (SCSI MMC - for ATAPI MMC)
+ * http://www.sata-io.org (SATA)
+ * http://www.compactflash.org (CF)
+ * http://www.qic.org (QIC157 - Tape and DSC)
+ * http://www.ce-ata.org (CE-ATA: not supported)
+ *
*/
#include <linux/kernel.h>
}
if ((dev->class == ATA_DEV_ATAPI) &&
- (atapi_command_packet_set(id) == TYPE_TAPE))
+ (atapi_command_packet_set(id) == TYPE_TAPE)) {
dev->max_sectors = ATA_MAX_SECTORS_TAPE;
+ dev->horkage |= ATA_HORKAGE_STUCK_ERR;
+ }
if (dev->horkage & ATA_HORKAGE_MAX_SEC_128)
dev->max_sectors = min_t(unsigned int, ATA_MAX_SECTORS_128,
}
}
-/**
- * __sata_phy_reset - Wake/reset a low-level SATA PHY
- * @ap: SATA port associated with target SATA PHY.
- *
- * This function issues commands to standard SATA Sxxx
- * PHY registers, to wake up the phy (and device), and
- * clear any reset condition.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- */
-void __sata_phy_reset(struct ata_port *ap)
-{
- struct ata_link *link = &ap->link;
- unsigned long timeout = jiffies + (HZ * 5);
- u32 sstatus;
-
- if (ap->flags & ATA_FLAG_SATA_RESET) {
- /* issue phy wake/reset */
- sata_scr_write_flush(link, SCR_CONTROL, 0x301);
- /* Couldn't find anything in SATA I/II specs, but
- * AHCI-1.1 10.4.2 says at least 1 ms. */
- mdelay(1);
- }
- /* phy wake/clear reset */
- sata_scr_write_flush(link, SCR_CONTROL, 0x300);
-
- /* wait for phy to become ready, if necessary */
- do {
- msleep(200);
- sata_scr_read(link, SCR_STATUS, &sstatus);
- if ((sstatus & 0xf) != 1)
- break;
- } while (time_before(jiffies, timeout));
-
- /* print link status */
- sata_print_link_status(link);
-
- /* TODO: phy layer with polling, timeouts, etc. */
- if (!ata_link_offline(link))
- ata_port_probe(ap);
- else
- ata_port_disable(ap);
-
- if (ap->flags & ATA_FLAG_DISABLED)
- return;
-
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
- ata_port_disable(ap);
- return;
- }
-
- ap->cbl = ATA_CBL_SATA;
-}
-
-/**
- * sata_phy_reset - Reset SATA bus.
- * @ap: SATA port associated with target SATA PHY.
- *
- * This function resets the SATA bus, and then probes
- * the bus for devices.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- */
-void sata_phy_reset(struct ata_port *ap)
-{
- __sata_phy_reset(ap);
- if (ap->flags & ATA_FLAG_DISABLED)
- return;
- ata_bus_reset(ap);
-}
-
/**
* ata_dev_pair - return other device on cable
* @adev: device
* let the EH abort the command or reset the device.
*/
if (unlikely(status & (ATA_ERR | ATA_DF))) {
- ata_port_printk(ap, KERN_WARNING, "DRQ=1 with device "
- "error, dev_stat 0x%X\n", status);
- qc->err_mask |= AC_ERR_HSM;
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
+ /* Some ATAPI tape drives forget to clear the ERR bit
+ * when doing the next command (mostly request sense).
+ * We ignore ERR here to workaround and proceed sending
+ * the CDB.
+ */
+ if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "DRQ=1 with device error, "
+ "dev_stat 0x%X\n", status);
+ qc->err_mask |= AC_ERR_HSM;
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
}
/* Send the CDB (atapi) or the first data block (ata pio out).
EXPORT_SYMBOL_GPL(sata_set_spd);
EXPORT_SYMBOL_GPL(sata_link_debounce);
EXPORT_SYMBOL_GPL(sata_link_resume);
-EXPORT_SYMBOL_GPL(sata_phy_reset);
-EXPORT_SYMBOL_GPL(__sata_phy_reset);
EXPORT_SYMBOL_GPL(ata_bus_reset);
EXPORT_SYMBOL_GPL(ata_std_prereset);
EXPORT_SYMBOL_GPL(ata_std_softreset);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(ata_port_pbar_desc);
#endif /* CONFIG_PCI */
-EXPORT_SYMBOL_GPL(ata_eng_timeout);
EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
EXPORT_SYMBOL_GPL(ata_link_abort);
EXPORT_SYMBOL_GPL(ata_port_abort);
}
}
-/**
- * ata_qc_timeout - Handle timeout of queued command
- * @qc: Command that timed out
- *
- * Some part of the kernel (currently, only the SCSI layer)
- * has noticed that the active command on port @ap has not
- * completed after a specified length of time. Handle this
- * condition by disabling DMA (if necessary) and completing
- * transactions, with error if necessary.
- *
- * This also handles the case of the "lost interrupt", where
- * for some reason (possibly hardware bug, possibly driver bug)
- * an interrupt was not delivered to the driver, even though the
- * transaction completed successfully.
- *
- * TODO: kill this function once old EH is gone.
- *
- * LOCKING:
- * Inherited from SCSI layer (none, can sleep)
- */
-static void ata_qc_timeout(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- u8 host_stat = 0, drv_stat;
- unsigned long flags;
-
- DPRINTK("ENTER\n");
-
- ap->hsm_task_state = HSM_ST_IDLE;
-
- spin_lock_irqsave(ap->lock, flags);
-
- switch (qc->tf.protocol) {
-
- case ATA_PROT_DMA:
- case ATA_PROT_ATAPI_DMA:
- host_stat = ap->ops->bmdma_status(ap);
-
- /* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(qc);
-
- /* fall through */
-
- default:
- ata_altstatus(ap);
- drv_stat = ata_chk_status(ap);
-
- /* ack bmdma irq events */
- ap->ops->irq_clear(ap);
-
- ata_dev_printk(qc->dev, KERN_ERR, "command 0x%x timeout, "
- "stat 0x%x host_stat 0x%x\n",
- qc->tf.command, drv_stat, host_stat);
-
- /* complete taskfile transaction */
- qc->err_mask |= AC_ERR_TIMEOUT;
- break;
- }
-
- spin_unlock_irqrestore(ap->lock, flags);
-
- ata_eh_qc_complete(qc);
-
- DPRINTK("EXIT\n");
-}
-
-/**
- * ata_eng_timeout - Handle timeout of queued command
- * @ap: Port on which timed-out command is active
- *
- * Some part of the kernel (currently, only the SCSI layer)
- * has noticed that the active command on port @ap has not
- * completed after a specified length of time. Handle this
- * condition by disabling DMA (if necessary) and completing
- * transactions, with error if necessary.
- *
- * This also handles the case of the "lost interrupt", where
- * for some reason (possibly hardware bug, possibly driver bug)
- * an interrupt was not delivered to the driver, even though the
- * transaction completed successfully.
- *
- * TODO: kill this function once old EH is gone.
- *
- * LOCKING:
- * Inherited from SCSI layer (none, can sleep)
- */
-void ata_eng_timeout(struct ata_port *ap)
-{
- DPRINTK("ENTER\n");
-
- ata_qc_timeout(ata_qc_from_tag(ap, ap->link.active_tag));
-
- DPRINTK("EXIT\n");
-}
-
static int ata_eh_nr_in_flight(struct ata_port *ap)
{
unsigned int tag;
if (!using_pio && ata_check_atapi_dma(qc))
using_pio = 1;
- /* Some controller variants snoop this value for Packet transfers
- to do state machine and FIFO management. Thus we want to set it
- properly, and for DMA where it is effectively meaningless */
+ /* Some controller variants snoop this value for Packet
+ * transfers to do state machine and FIFO management. Thus we
+ * want to set it properly, and for DMA where it is
+ * effectively meaningless.
+ */
nbytes = min(qc->nbytes, (unsigned int)63 * 1024);
+ /* Most ATAPI devices which honor transfer chunk size don't
+ * behave according to the spec when odd chunk size which
+ * matches the transfer length is specified. If the number of
+ * bytes to transfer is 2n+1. According to the spec, what
+ * should happen is to indicate that 2n+1 is going to be
+ * transferred and transfer 2n+2 bytes where the last byte is
+ * padding.
+ *
+ * In practice, this doesn't happen. ATAPI devices first
+ * indicate and transfer 2n bytes and then indicate and
+ * transfer 2 bytes where the last byte is padding.
+ *
+ * This inconsistency confuses several controllers which
+ * perform PIO using DMA such as Intel AHCIs and sil3124/32.
+ * These controllers use actual number of transferred bytes to
+ * update DMA poitner and transfer of 4n+2 bytes make those
+ * controller push DMA pointer by 4n+4 bytes because SATA data
+ * FISes are aligned to 4 bytes. This causes data corruption
+ * and buffer overrun.
+ *
+ * Always setting nbytes to even number solves this problem
+ * because then ATAPI devices don't have to split data at 2n
+ * boundaries.
+ */
+ if (nbytes & 0x1)
+ nbytes++;
+
qc->tf.lbam = (nbytes & 0xFF);
qc->tf.lbah = (nbytes >> 8);
xlat_func = NULL;
if (likely((scsi_op != ATA_16) || !atapi_passthru16)) {
/* relay SCSI command to ATAPI device */
- if (unlikely(scmd->cmd_len > dev->cdb_len))
+ int len = COMMAND_SIZE(scsi_op);
+ if (unlikely(len > scmd->cmd_len || len > dev->cdb_len))
goto bad_cdb_len;
xlat_func = atapi_xlat;
/* Fujitsu P2000 */
if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
return 1;
+ /* Mitac 8317 (Winbook-A) and relatives */
+ if (pdev->subsystem_vendor == 0x1071 && pdev->subsystem_device == 0x8317)
+ return 1;
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
adev->max_sectors = 255;
}
+/**
+ * ali_check_atapi_dma - DMA check for most ALi controllers
+ * @adev: Device
+ *
+ * Called to decide whether commands should be sent by DMA or PIO
+ */
+
+static int ali_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ /* If its not a media command, its not worth it */
+ if (qc->nbytes < 2048)
+ return -EOPNOTSUPP;
+ return 0;
+}
+
static struct scsi_host_template ali_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
+ .check_atapi_dma = ali_check_atapi_dma,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
+ .check_atapi_dma = ali_check_atapi_dma,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
unsigned short int_status = ATAPI_GET_INT_STATUS(base);
if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON|ULTRA_XFER_ON)) {
- host_stat = ATA_DMA_ACTIVE;
+ host_stat |= ATA_DMA_ACTIVE;
}
if (int_status & (MULTI_DONE_INT|UDMAIN_DONE_INT|UDMAOUT_DONE_INT)) {
- host_stat = ATA_DMA_INTR;
+ host_stat |= ATA_DMA_INTR;
}
if (int_status & (MULTI_TERM_INT|UDMAIN_TERM_INT|UDMAOUT_TERM_INT)) {
- host_stat = ATA_DMA_ERR;
+ host_stat |= ATA_DMA_ERR;
}
return host_stat;
/* Restore state */
pci_write_config_byte(pdev, 0x5B, scr2);
- if (ata66 & (1 << ap->port_no))
+ if (ata66 & (2 >> ap->port_no))
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
struct ata_host *host;
struct ata_port *ap;
void __iomem *cmd_addr, *ctl_addr;
+ int irq = 0;
+ irq_handler_t handler = NULL;
if (pnp_port_valid(idev, 0) == 0)
return -ENODEV;
- /* FIXME: Should selected polled PIO here not fail */
- if (pnp_irq_valid(idev, 0) == 0)
- return -ENODEV;
+ if (pnp_irq_valid(idev, 0)) {
+ irq = pnp_irq(idev, 0);
+ handler = ata_interrupt;
+ }
/* allocate host */
host = ata_host_alloc(&idev->dev, 1);
(unsigned long long)pnp_port_start(idev, 1));
/* activate */
- return ata_host_activate(host, pnp_irq(idev, 0), ata_interrupt, 0,
+ return ata_host_activate(host, irq, handler, 0,
&isapnp_sht);
}
* actually do our cable checking etc. Thankfully we don't need
* to do the plumbing for other cases.
*/
- switch (port_map[port])
- {
+ switch (port_map[port]) {
case PORT_PATA0:
- if (control & (1 << 5))
- return 0;
+ if ((control & (1 << 5)) == 0)
+ return -ENOENT;
if (control & (1 << 3)) /* 40/80 pin primary */
ap->cbl = ATA_CBL_PATA40;
else
case PORT_PATA1:
/* Bit 21 is set if the port is enabled */
if ((control5 & (1 << 21)) == 0)
- return 0;
+ return -ENOENT;
if (control5 & (1 << 19)) /* 40/80 pin secondary */
ap->cbl = ATA_CBL_PATA40;
else
#include <linux/libata.h>
#define DRV_NAME "pata_sil680"
-#define DRV_VERSION "0.4.7"
+#define DRV_VERSION "0.4.8"
#define SIL680_MMIO_BAR 5
return ATA_CBL_PATA40;
}
-/**
- * sil680_bus_reset - reset the SIL680 bus
- * @link: ATA link to reset
- * @deadline: deadline jiffies for the operation
- *
- * Perform the SIL680 housekeeping when doing an ATA bus reset
- */
-
-static int sil680_bus_reset(struct ata_link *link, unsigned int *classes,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned long addr = sil680_selreg(ap, 0);
- u8 reset;
-
- pci_read_config_byte(pdev, addr, &reset);
- pci_write_config_byte(pdev, addr, reset | 0x03);
- udelay(25);
- pci_write_config_byte(pdev, addr, reset);
- return ata_std_softreset(link, classes, deadline);
-}
-
-static void sil680_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, ata_std_prereset, sil680_bus_reset, NULL, ata_std_postreset);
-}
-
/**
* sil680_set_piomode - set initial PIO mode data
* @ap: ATA interface
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sil680_error_handler,
+ .error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = sil680_cable_detect,
/* devid, subvendor, subdev */
{ 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
{ 0x5513, 0x1734, 0x105F }, /* FSC Amilo A1630 */
+ { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
/* end marker */
{ 0, }
};
SIL24_HOST_BAR = 0,
SIL24_PORT_BAR = 2,
+ /* sil24 fetches in chunks of 64bytes. The first block
+ * contains the PRB and two SGEs. From the second block, it's
+ * consisted of four SGEs and called SGT. Calculate the
+ * number of SGTs that fit into one page.
+ */
+ SIL24_PRB_SZ = sizeof(struct sil24_prb)
+ + 2 * sizeof(struct sil24_sge),
+ SIL24_MAX_SGT = (PAGE_SIZE - SIL24_PRB_SZ)
+ / (4 * sizeof(struct sil24_sge)),
+
+ /* This will give us one unused SGEs for ATA. This extra SGE
+ * will be used to store CDB for ATAPI devices.
+ */
+ SIL24_MAX_SGE = 4 * SIL24_MAX_SGT + 1,
+
/*
* Global controller registers (128 bytes @ BAR0)
*/
struct sil24_ata_block {
struct sil24_prb prb;
- struct sil24_sge sge[LIBATA_MAX_PRD];
+ struct sil24_sge sge[SIL24_MAX_SGE];
};
struct sil24_atapi_block {
struct sil24_prb prb;
u8 cdb[16];
- struct sil24_sge sge[LIBATA_MAX_PRD - 1];
+ struct sil24_sge sge[SIL24_MAX_SGE];
};
union sil24_cmd_block {
.change_queue_depth = ata_scsi_change_queue_depth,
.can_queue = SIL24_MAX_CMDS,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = SIL24_MAX_SGE,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
+ extern int __MARKER__sil24_cmd_block_is_sized_wrongly;
static int printed_version;
struct ata_port_info pi = sil24_port_info[ent->driver_data];
const struct ata_port_info *ppi[] = { &pi, NULL };
int i, rc;
u32 tmp;
+ /* cause link error if sil24_cmd_block is sized wrongly */
+ if (sizeof(union sil24_cmd_block) != PAGE_SIZE)
+ __MARKER__sil24_cmd_block_is_sized_wrongly = 1;
+
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
he_dev->atm_dev->dev_data = he_dev;
atm_dev->dev_data = he_dev;
he_dev->number = atm_dev->number;
+#ifdef USE_TASKLET
+ tasklet_init(&he_dev->tasklet, he_tasklet, (unsigned long) he_dev);
+#endif
+ spin_lock_init(&he_dev->global_lock);
+
if (he_start(atm_dev)) {
he_stop(he_dev);
err = -ENODEV;
if ((err = he_init_irq(he_dev)) != 0)
return err;
-#ifdef USE_TASKLET
- tasklet_init(&he_dev->tasklet, he_tasklet, (unsigned long) he_dev);
-#endif
- spin_lock_init(&he_dev->global_lock);
-
/* 4.11 enable pci bus controller state machines */
host_cntl |= (OUTFF_ENB | CMDFF_ENB |
QUICK_RD_RETRY | QUICK_WR_RETRY | PERR_INT_ENB);
err = virtio_config_val(vdev, VIRTIO_CONFIG_BLK_F_CAPACITY, &cap);
if (err) {
dev_err(&vdev->dev, "Bad/missing capacity in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
/* If capacity is too big, truncate with warning. */
blk_queue_max_segment_size(vblk->disk->queue, v);
else if (err != -ENOENT) {
dev_err(&vdev->dev, "Bad SIZE_MAX in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
err = virtio_config_val(vdev, VIRTIO_CONFIG_BLK_F_SEG_MAX, &v);
blk_queue_max_hw_segments(vblk->disk->queue, v);
else if (err != -ENOENT) {
dev_err(&vdev->dev, "Bad SEG_MAX in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
add_disk(vblk->disk);
return 0;
+out_cleanup_queue:
+ blk_cleanup_queue(vblk->disk->queue);
out_put_disk:
put_disk(vblk->disk);
out_unregister_blkdev:
put_disk(vblk->disk);
unregister_blkdev(major, "virtblk");
mempool_destroy(vblk->pool);
+ /* There should be nothing in the queue now, so no need to shutdown */
+ vdev->config->del_vq(vblk->vq);
kfree(vblk);
}
};
#endif
-static int __devinit sonypi_create_input_devices(void)
+static int __devinit sonypi_create_input_devices(struct platform_device *pdev)
{
struct input_dev *jog_dev;
struct input_dev *key_dev;
jog_dev->name = "Sony Vaio Jogdial";
jog_dev->id.bustype = BUS_ISA;
jog_dev->id.vendor = PCI_VENDOR_ID_SONY;
+ jog_dev->dev.parent = &pdev->dev;
jog_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL);
jog_dev->keybit[BIT_WORD(BTN_MOUSE)] = BIT_MASK(BTN_MIDDLE);
key_dev->name = "Sony Vaio Keys";
key_dev->id.bustype = BUS_ISA;
key_dev->id.vendor = PCI_VENDOR_ID_SONY;
+ key_dev->dev.parent = &pdev->dev;
/* Initialize the Input Drivers: special keys */
key_dev->evbit[0] = BIT_MASK(EV_KEY);
if (useinput) {
- error = sonypi_create_input_devices();
+ error = sonypi_create_input_devices(dev);
if (error) {
printk(KERN_ERR
"sonypi: failed to create input devices\n");
{
sonypi_disable();
- synchronize_sched(); /* Allow sonypi interrupt to complete. */
+ synchronize_irq(sonypi_device.irq);
flush_scheduled_work();
if (useinput) {
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- default H8300
help
If unsure, say N.
config BLK_DEV_AMD74XX
tristate "AMD and nVidia IDE support"
+ depends on !ARM
select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for AMD-7xx and AMD-8111 chips
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
+config ETRAX_IDE
+ bool "ETRAX IDE support"
+ depends on CRIS && BROKEN
+ select BLK_DEV_IDEDMA
+ select IDE_GENERIC
+ help
+ Enables the ETRAX IDE driver.
+
+ You can't use parallel ports or SCSI ports at the same time.
+
+config ETRAX_IDE_DELAY
+ int "Delay for drives to regain consciousness"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default 15
+ help
+ Number of seconds to wait for IDE drives to spin up after an IDE
+ reset.
+
+choice
+ prompt "IDE reset pin"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default ETRAX_IDE_PB7_RESET
+
+config ETRAX_IDE_PB7_RESET
+ bool "Port_PB_Bit_7"
+ help
+ IDE reset on pin 7 on port B
+
+config ETRAX_IDE_G27_RESET
+ bool "Port_G_Bit_27"
+ help
+ IDE reset on pin 27 on port G
+
+endchoice
+
+config IDE_H8300
+ bool "H8300 IDE support"
+ depends on H8300
+ select IDE_GENERIC
+ default y
+ help
+ Enables the H8300 IDE driver.
+
config BLK_DEV_GAYLE
bool "Amiga Gayle IDE interface support"
depends on AMIGA
config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on 8xx && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
+ depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
select IDE_GENERIC
help
This option provides support for IDE on Motorola MPC8xx Systems.
ide-core-$(CONFIG_BLK_DEV_IDE_PMAC) += ppc/pmac.o
# built-in only drivers from h8300/
-ide-core-$(CONFIG_H8300) += h8300/ide-h8300.o
+ide-core-$(CONFIG_IDE_H8300) += h8300/ide-h8300.o
obj-$(CONFIG_BLK_DEV_IDE) += ide-core.o
obj-$(CONFIG_IDE_GENERIC) += ide-generic.o
/* the IDE control register is at ATA address 6, with CS1 active instead of CS0 */
ide_offsets[IDE_CONTROL_OFFSET] = cris_ide_reg_addr(6, 1, 0);
- /* first fill in some stuff in the ide_hwifs fields */
+ for (h = 0; h < 4; h++) {
+ ide_hwif_t *hwif = NULL;
- for(h = 0; h < MAX_HWIFS; h++) {
- ide_hwif_t *hwif = &ide_hwifs[h];
ide_setup_ports(&hw, cris_ide_base_address(h),
ide_offsets,
0, 0, cris_ide_ack_intr,
ide_default_irq(0));
ide_register_hw(&hw, NULL, 1, &hwif);
+ if (hwif == NULL)
+ continue;
hwif->mmio = 1;
hwif->chipset = ide_etrax100;
hwif->set_pio_mode = &cris_set_pio_mode;
{ "_NEC DV5800A", NULL },
{ "SAMSUNG CD-ROM SN-124", "N001" },
{ "Seagate STT20000A", NULL },
+ { "CD-ROM CDR_U200", "1.09" },
{ NULL , NULL }
};
hwif->atapi_output_bytes = atapi_output_bytes;
}
-/*
- * Beginning of Taskfile OPCODE Library and feature sets.
- */
void ide_fix_driveid (struct hd_driveid *id)
{
#ifndef __LITTLE_ENDIAN
static const struct drive_list_entry ivb_list[] = {
{ "QUANTUM FIREBALLlct10 05" , "A03.0900" },
{ "TSSTcorp CDDVDW SH-S202J" , "SB00" },
+ { "TSSTcorp CDDVDW SH-S202J" , "SB01" },
+ { "TSSTcorp CDDVDW SH-S202N" , "SB00" },
+ { "TSSTcorp CDDVDW SH-S202N" , "SB01" },
{ NULL , NULL }
};
int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
{
ide_hwif_t *hwif = drive->hwif;
- int error;
+ int error = 0;
u8 stat;
// while (HWGROUP(drive)->busy)
hwif->dma_host_off(drive);
#endif
+ /* Skip setting PIO flow-control modes on pre-EIDE drives */
+ if ((speed & 0xf8) == XFER_PIO_0 && !(drive->id->capability & 0x08))
+ goto skip;
+
/*
* Don't use ide_wait_cmd here - it will
* attempt to set_geometry and recalibrate,
drive->id->dma_mword &= ~0x0F00;
drive->id->dma_1word &= ~0x0F00;
+ skip:
#ifdef CONFIG_BLK_DEV_IDEDMA
if (speed >= XFER_SW_DMA_0)
hwif->dma_host_on(drive);
static int wait_hwif_ready(ide_hwif_t *hwif)
{
- int rc;
+ int unit, rc;
printk(KERN_DEBUG "Probing IDE interface %s...\n", hwif->name);
return rc;
/* Now make sure both master & slave are ready */
- SELECT_DRIVE(&hwif->drives[0]);
- hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
- mdelay(2);
- rc = ide_wait_not_busy(hwif, 35000);
- if (rc)
- return rc;
- SELECT_DRIVE(&hwif->drives[1]);
- hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
- mdelay(2);
- rc = ide_wait_not_busy(hwif, 35000);
+ for (unit = 0; unit < MAX_DRIVES; unit++) {
+ ide_drive_t *drive = &hwif->drives[unit];
+ /* Ignore disks that we will not probe for later. */
+ if (!drive->noprobe || drive->present) {
+ SELECT_DRIVE(drive);
+ hwif->OUTB(8, hwif->io_ports[IDE_CONTROL_OFFSET]);
+ mdelay(2);
+ rc = ide_wait_not_busy(hwif, 35000);
+ if (rc)
+ goto out;
+ } else
+ printk(KERN_DEBUG "%s: ide_wait_not_busy() skipped\n",
+ drive->name);
+ }
+out:
/* Exit function with master reselected (let's be sane) */
- SELECT_DRIVE(&hwif->drives[0]);
-
+ if (unit)
+ SELECT_DRIVE(&hwif->drives[0]);
+
return rc;
}
/* port addresses for auto-detection */
#define ALI_NUM_PORTS 4
-static int ports[ALI_NUM_PORTS] __initdata = {0x074, 0x0f4, 0x034, 0x0e4};
+static const int ports[ALI_NUM_PORTS] __initdata =
+ { 0x074, 0x0f4, 0x034, 0x0e4 };
/* register initialization data */
typedef struct { u8 reg, data; } RegInitializer;
-static RegInitializer initData[] __initdata = {
+static const RegInitializer initData[] __initdata = {
{0x01, 0x0f}, {0x02, 0x00}, {0x03, 0x00}, {0x04, 0x00},
{0x05, 0x00}, {0x06, 0x00}, {0x07, 0x2b}, {0x0a, 0x0f},
{0x25, 0x00}, {0x26, 0x00}, {0x27, 0x00}, {0x28, 0x00},
* Initialize controller registers with default values.
*/
static int __init initRegisters (void) {
- RegInitializer *p;
+ const RegInitializer *p;
u8 t;
unsigned long flags;
* Probe for a Macintosh IDE interface
*/
-void macide_init(void)
+void __init macide_init(void)
{
hw_regs_t hw;
ide_hwif_t *hwif;
* Probe for Q40 IDE interfaces
*/
-void q40ide_init(void)
+void __init q40ide_init(void)
{
int i;
ide_hwif_t *hwif;
{
struct ide_port_info d;
u8 idx = id->driver_data;
+ int err;
+
+ err = pci_enable_device(dev);
+ if (err)
+ return err;
d = aec62xx_chipsets[idx];
}
}
- return ide_setup_pci_device(dev, &d);
+ err = ide_setup_pci_device(dev, &d);
+ if (err)
+ pci_disable_device(dev);
+
+ return err;
}
static const struct pci_device_id aec62xx_pci_tbl[] = {
pdev->subsystem_device == 0x10AF)
return 1;
+ /* Mitac 8317 (Winbook-A) and relatives */
+ if (pdev->subsystem_vendor == 0x1071 &&
+ pdev->subsystem_device == 0x8317)
+ return 1;
+
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
{ 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
{ 0x27DF, 0x1025, 0x0110 }, /* ICH7 on Acer 3682WLMi */
{ 0x27DF, 0x1043, 0x1267 }, /* ICH7 on Asus W5F */
+ { 0x27DF, 0x103C, 0x30A1 }, /* ICH7 on HP Compaq nc2400 */
{ 0x24CA, 0x1025, 0x0061 }, /* ICH4 on Acer Aspire 2023WLMi */
/* end marker */
{ 0, }
/*
- * linux/drivers/ide/pci/siimage.c Version 1.18 Oct 18 2007
+ * linux/drivers/ide/pci/siimage.c Version 1.19 Nov 16 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
}
}
-/**
- * siimage_reset - reset a device on an siimage controller
- * @drive: drive to reset
- *
- * Perform a controller level reset fo the device. For
- * SATA we must also check the PHY.
- */
-
-static void siimage_reset (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = HWIF(drive);
- u8 reset = 0;
- unsigned long addr = siimage_selreg(hwif, 0);
-
- if (hwif->mmio) {
- reset = hwif->INB(addr);
- hwif->OUTB((reset|0x03), addr);
- /* FIXME:posting */
- udelay(25);
- hwif->OUTB(reset, addr);
- (void) hwif->INB(addr);
- } else {
- pci_read_config_byte(hwif->pci_dev, addr, &reset);
- pci_write_config_byte(hwif->pci_dev, addr, reset|0x03);
- udelay(25);
- pci_write_config_byte(hwif->pci_dev, addr, reset);
- pci_read_config_byte(hwif->pci_dev, addr, &reset);
- }
-
- if (SATA_STATUS_REG) {
- /* SATA_STATUS_REG is valid only when in MMIO mode */
- u32 sata_stat = readl((void __iomem *)SATA_STATUS_REG);
- printk(KERN_WARNING "%s: reset phy, status=0x%08x, %s\n",
- hwif->name, sata_stat, __FUNCTION__);
- if (!(sata_stat)) {
- printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
- hwif->name, sata_stat);
- drive->failures++;
- }
- }
-}
-
/**
* proc_reports_siimage - add siimage controller to proc
* @dev: PCI device
{
u8 sata = is_sata(hwif);
- hwif->resetproc = &siimage_reset;
hwif->set_pio_mode = &sil_set_pio_mode;
hwif->set_dma_mode = &sil_set_dma_mode;
/* devid, subvendor, subdev */
{ 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
{ 0x5513, 0x1734, 0x105f }, /* FSC Amilo A1630 */
+ { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
/* end marker */
{ 0, }
};
return (status == 0x00ff);
}
-/*
- * Invoked from ide-dma.c at boot time.
- */
static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
{
unsigned int cfgbase = 0;
if (pmif->broken_dma && cur_addr & (L1_CACHE_BYTES - 1)) {
if (pmif->broken_dma_warn == 0) {
- printk(KERN_WARNING "%s: DMA on non aligned address,"
+ printk(KERN_WARNING "%s: DMA on non aligned address, "
"switching to PIO on Ohare chipset\n", drive->name);
pmif->broken_dma_warn = 1;
}
mqpcb->service_level = attr->ah_attr.sl;
update_mask |= EHCA_BMASK_SET(MQPCB_MASK_SERVICE_LEVEL, 1);
- if (ehca_calc_ipd(shca, my_qp->init_attr.port_num,
+ if (ehca_calc_ipd(shca, mqpcb->prim_phys_port,
attr->ah_attr.static_rate,
&mqpcb->max_static_rate)) {
ret = -EINVAL;
mqpcb->source_path_bits_al = attr->alt_ah_attr.src_path_bits;
mqpcb->service_level_al = attr->alt_ah_attr.sl;
- if (ehca_calc_ipd(shca, my_qp->init_attr.port_num,
+ if (ehca_calc_ipd(shca, mqpcb->alt_phys_port,
attr->alt_ah_attr.static_rate,
&mqpcb->max_static_rate_al)) {
ret = -EINVAL;
goto bail;
}
- /*
- * Return the address of the WC as the offset to mmap.
- * See ipath_mmap() for details.
- */
+ /* Check that we can write the offset to mmap. */
if (udata && udata->outlen >= sizeof(__u64)) {
- __u64 offset = (__u64) wc;
+ __u64 offset = 0;
ret = ib_copy_to_udata(udata, &offset, sizeof(offset));
if (ret)
struct ipath_mmap_info *ip = cq->ip;
ipath_update_mmap_info(dev, ip, sz, wc);
+
+ /*
+ * Return the offset to mmap.
+ * See ipath_mmap() for details.
+ */
+ if (udata && udata->outlen >= sizeof(__u64)) {
+ ret = ib_copy_to_udata(udata, &ip->offset,
+ sizeof(ip->offset));
+ if (ret)
+ goto bail;
+ }
+
spin_lock_irq(&dev->pending_lock);
if (list_empty(&ip->pending_mmaps))
list_add(&ip->pending_mmaps, &dev->pending_mmaps);
init_attr->qp_type);
if (err) {
ret = ERR_PTR(err);
- goto bail_rwq;
+ vfree(qp->r_rq.wq);
+ goto bail_qp;
}
qp->ip = NULL;
ipath_reset_qp(qp);
sizeof(offset));
if (err) {
ret = ERR_PTR(err);
- goto bail_rwq;
+ goto bail_ip;
}
} else {
u32 s = sizeof(struct ipath_rwq) +
qp->r_rq.wq);
if (!qp->ip) {
ret = ERR_PTR(-ENOMEM);
- goto bail_rwq;
+ goto bail_ip;
}
err = ib_copy_to_udata(udata, &(qp->ip->offset),
goto bail;
bail_ip:
- kfree(qp->ip);
-bail_rwq:
- vfree(qp->r_rq.wq);
+ if (qp->ip)
+ kref_put(&qp->ip->ref, ipath_release_mmap_info);
+ else
+ vfree(qp->r_rq.wq);
+ ipath_free_qp(&dev->qp_table, qp);
bail_qp:
kfree(qp);
bail_swq:
if ((unsigned) wr->num_sge > srq->rq.max_sge) {
*bad_wr = wr;
- ret = -ENOMEM;
+ ret = -EINVAL;
goto bail;
}
struct ib_udata *udata)
{
struct ipath_srq *srq = to_isrq(ibsrq);
+ struct ipath_rwq *wq;
int ret = 0;
if (attr_mask & IB_SRQ_MAX_WR) {
struct ipath_rwq *owq;
- struct ipath_rwq *wq;
struct ipath_rwqe *p;
u32 sz, size, n, head, tail;
goto bail;
}
- /*
- * Return the address of the RWQ as the offset to mmap.
- * See ipath_mmap() for details.
- */
+ /* Check that we can write the offset to mmap. */
if (udata && udata->inlen >= sizeof(__u64)) {
__u64 offset_addr;
- __u64 offset = (__u64) wq;
+ __u64 offset = 0;
ret = ib_copy_from_udata(&offset_addr, udata,
sizeof(offset_addr));
- if (ret) {
- vfree(wq);
- goto bail;
- }
+ if (ret)
+ goto bail_free;
udata->outbuf = (void __user *) offset_addr;
ret = ib_copy_to_udata(udata, &offset,
sizeof(offset));
- if (ret) {
- vfree(wq);
- goto bail;
- }
+ if (ret)
+ goto bail_free;
}
spin_lock_irq(&srq->rq.lock);
else
n -= tail;
if (size <= n) {
- spin_unlock_irq(&srq->rq.lock);
- vfree(wq);
ret = -EINVAL;
- goto bail;
+ goto bail_unlock;
}
n = 0;
p = wq->wq;
u32 s = sizeof(struct ipath_rwq) + size * sz;
ipath_update_mmap_info(dev, ip, s, wq);
+
+ /*
+ * Return the offset to mmap.
+ * See ipath_mmap() for details.
+ */
+ if (udata && udata->inlen >= sizeof(__u64)) {
+ ret = ib_copy_to_udata(udata, &ip->offset,
+ sizeof(ip->offset));
+ if (ret)
+ goto bail;
+ }
+
spin_lock_irq(&dev->pending_lock);
if (list_empty(&ip->pending_mmaps))
list_add(&ip->pending_mmaps,
srq->limit = attr->srq_limit;
spin_unlock_irq(&srq->rq.lock);
}
+ goto bail;
+bail_unlock:
+ spin_unlock_irq(&srq->rq.lock);
+bail_free:
+ vfree(wq);
bail:
return ret;
}
next = qp->s_head + 1;
if (next >= qp->s_size)
next = 0;
- if (next == qp->s_last)
- goto bail_inval;
+ if (next == qp->s_last) {
+ ret = -ENOMEM;
+ goto bail;
+ }
wqe = get_swqe_ptr(qp, qp->s_head);
wqe->wr = *wr;
if ((unsigned) wr->num_sge > qp->r_rq.max_sge) {
*bad_wr = wr;
- ret = -ENOMEM;
+ ret = -EINVAL;
goto bail;
}
if (i + 1 < data->dma_nents) {
next_addr = ib_sg_dma_address(ibdev, sg_next(sg));
/* are i, i+1 fragments of the same page? */
- if (end_addr == next_addr)
+ if (end_addr == next_addr) {
+ cnt++;
continue;
- else if (!IS_4K_ALIGNED(end_addr)) {
+ } else if (!IS_4K_ALIGNED(end_addr)) {
ret_len = cnt + 1;
break;
}
}
+ cnt++;
}
if (i == data->dma_nents)
ret_len = cnt; /* loop ended */
config KEYBOARD_BFIN
tristate "Blackfin BF54x keypad support"
- depends on BF54x
+ depends on (BF54x && !BF544)
help
Say Y here if you want to use the BF54x keypad.
for (i = 0; i < pdata->nbuttons; i++) {
struct gpio_keys_button *button = &pdata->buttons[i];
- int irq = gpio_to_irq(button->gpio);
+ int irq;
unsigned int type = button->type ?: EV_KEY;
+ error = gpio_request(button->gpio, button->desc ?: "gpio_keys");
+ if (error < 0) {
+ pr_err("gpio-keys: failed to request GPIO %d,"
+ " error %d\n", button->gpio, error);
+ goto fail;
+ }
+
+ error = gpio_direction_input(button->gpio);
+ if (error < 0) {
+ pr_err("gpio-keys: failed to configure input"
+ " direction for GPIO %d, error %d\n",
+ button->gpio, error);
+ gpio_free(button->gpio);
+ goto fail;
+ }
+
+ irq = gpio_to_irq(button->gpio);
if (irq < 0) {
error = irq;
- printk(KERN_ERR
- "gpio-keys: "
- "Unable to get irq number for GPIO %d,"
- "error %d\n",
+ pr_err("gpio-keys: Unable to get irq number"
+ " for GPIO %d, error %d\n",
button->gpio, error);
+ gpio_free(button->gpio);
goto fail;
}
button->desc ? button->desc : "gpio_keys",
pdev);
if (error) {
- printk(KERN_ERR
- "gpio-keys: Unable to claim irq %d; error %d\n",
+ pr_err("gpio-keys: Unable to claim irq %d; error %d\n",
irq, error);
+ gpio_free(button->gpio);
goto fail;
}
error = input_register_device(input);
if (error) {
- printk(KERN_ERR
- "gpio-keys: Unable to register input device, "
+ pr_err("gpio-keys: Unable to register input device, "
"error: %d\n", error);
goto fail;
}
return 0;
fail:
- while (--i >= 0)
+ while (--i >= 0) {
free_irq(gpio_to_irq(pdata->buttons[i].gpio), pdev);
+ gpio_free(pdata->buttons[i].gpio);
+ }
platform_set_drvdata(pdev, NULL);
input_free_device(input);
for (i = 0; i < pdata->nbuttons; i++) {
int irq = gpio_to_irq(pdata->buttons[i].gpio);
free_irq(irq, pdev);
+ gpio_free(pdata->buttons[i].gpio);
}
input_unregister_device(input);
config SERIO_I8042
tristate "i8042 PC Keyboard controller" if EMBEDDED || !X86
default y
- depends on !PARISC && (!ARM || ARCH_SHARK || FOOTBRIDGE_HOST) && !M68K && !BFIN
+ depends on !PARISC && (!ARM || ARCH_SHARK || FOOTBRIDGE_HOST) && !M68K && !BLACKFIN
---help---
i8042 is the chip over which the standard AT keyboard and PS/2
mouse are connected to the computer. If you use these devices,
DMI_MATCH(DMI_PRODUCT_VERSION, "5a"),
},
},
+ {
+ .ident = "Microsoft Virtual Machine",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Virtual Machine"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "VS2005R2"),
+ },
+ },
{ }
};
u_long flags;
isdn_net_dev *p;
isdn_net_phone *n;
- char nr[32];
+ char nr[ISDN_MSNLEN];
char *my_eaz;
/* Search name in netdev-chain */
nr[1] = '\0';
printk(KERN_INFO "isdn_net: Incoming call without OAD, assuming '0'\n");
} else
- strcpy(nr, setup->phone);
+ strlcpy(nr, setup->phone, ISDN_MSNLEN);
si1 = (int) setup->si1;
si2 = (int) setup->si2;
if (!setup->eazmsn[0]) {
chidx = -1;
}
}
- strcpy(lp->msn, cfg->eaz);
+ strlcpy(lp->msn, cfg->eaz, sizeof(lp->msn));
lp->pre_device = drvidx;
lp->pre_channel = chidx;
lp->onhtime = cfg->onhtime;
if (p) {
if (!(n = kmalloc(sizeof(isdn_net_phone), GFP_KERNEL)))
return -ENOMEM;
- strcpy(n->num, phone->phone);
+ strlcpy(n->num, phone->phone, sizeof(n->num));
n->next = p->local->phone[phone->outgoing & 1];
p->local->phone[phone->outgoing & 1] = n;
return 0;
int emulate_clts(struct kvm_vcpu *vcpu)
{
- vcpu->cr0 &= ~X86_CR0_TS;
- kvm_x86_ops->set_cr0(vcpu, vcpu->cr0);
+ kvm_x86_ops->set_cr0(vcpu, vcpu->cr0 & ~X86_CR0_TS);
return X86EMUL_CONTINUE;
}
wrmsrl(host_save_user_msrs[i], svm->host_user_msrs[i]);
rdtscll(vcpu->host_tsc);
+ kvm_put_guest_fpu(vcpu);
}
static void svm_vcpu_decache(struct kvm_vcpu *vcpu)
#define JMP_REL(rel) \
do { \
- _eip += (int)(rel); \
- _eip = ((op_bytes == 2) ? (uint16_t)_eip : (uint32_t)_eip); \
+ register_address_increment(_eip, rel); \
} while (0)
/*
}
register_address_increment(_regs[VCPU_REGS_RSP],
-dst.bytes);
- if ((rc = ops->write_std(
+ if ((rc = ops->write_emulated(
register_address(ctxt->ss_base,
_regs[VCPU_REGS_RSP]),
&dst.val, dst.bytes, ctxt->vcpu)) != 0)
}
src.val = (unsigned long) _eip;
JMP_REL(rel);
+ op_bytes = ad_bytes;
goto push;
}
case 0xe9: /* jmp rel */
{
struct lguest_vq_info *lvq = vq->priv;
+ /* Release the interrupt */
+ free_irq(lvq->config.irq, vq);
/* Tell virtio_ring.c to free the virtqueue. */
vring_del_virtqueue(vq);
/* Unmap the pages containing the ring. */
dprintk("unknown input event %.2x\n", event);
}
-static int sony_laptop_setup_input(void)
+static int sony_laptop_setup_input(struct acpi_device *acpi_device)
{
struct input_dev *jog_dev;
struct input_dev *key_dev;
key_dev->name = "Sony Vaio Keys";
key_dev->id.bustype = BUS_ISA;
key_dev->id.vendor = PCI_VENDOR_ID_SONY;
+ key_dev->dev.parent = &acpi_device->dev;
/* Initialize the Input Drivers: special keys */
set_bit(EV_KEY, key_dev->evbit);
jog_dev->name = "Sony Vaio Jogdial";
jog_dev->id.bustype = BUS_ISA;
jog_dev->id.vendor = PCI_VENDOR_ID_SONY;
+ key_dev->dev.parent = &acpi_device->dev;
jog_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL);
jog_dev->keybit[BIT_WORD(BTN_MOUSE)] = BIT_MASK(BTN_MIDDLE);
}
/* setup input devices and helper fifo */
- result = sony_laptop_setup_input();
+ result = sony_laptop_setup_input(device);
if (result) {
printk(KERN_ERR DRV_PFX
"Unabe to create input devices.\n");
sony_backlight_device->props.brightness =
sony_backlight_get_brightness
(sony_backlight_device);
- sony_backlight_device->props.max_brightness =
+ sony_backlight_device->props.max_brightness =
SONY_MAX_BRIGHTNESS - 1;
}
}
/* setup input devices and helper fifo */
- result = sony_laptop_setup_input();
+ result = sony_laptop_setup_input(device);
if (result) {
printk(KERN_ERR DRV_PFX
"Unabe to create input devices.\n");
* 02110-1301, USA.
*/
-#define IBM_VERSION "0.16"
+#define IBM_VERSION "0.17"
#define TPACPI_SYSFS_VERSION 0x020000
/*
KEY_UNKNOWN, /* 0x0C: FN+BACKSPACE */
KEY_UNKNOWN, /* 0x0D: FN+INSERT */
KEY_UNKNOWN, /* 0x0E: FN+DELETE */
- KEY_BRIGHTNESSUP, /* 0x0F: FN+HOME (brightness up) */
+ KEY_RESERVED, /* 0x0F: FN+HOME (brightness up) */
/* Scan codes 0x10 to 0x1F: Extended ACPI HKEY hot keys */
- KEY_BRIGHTNESSDOWN, /* 0x10: FN+END (brightness down) */
+ KEY_RESERVED, /* 0x10: FN+END (brightness down) */
KEY_RESERVED, /* 0x11: FN+PGUP (thinklight toggle) */
KEY_UNKNOWN, /* 0x12: FN+PGDOWN */
KEY_ZOOM, /* 0x13: FN+SPACE (zoom) */
- KEY_VOLUMEUP, /* 0x14: VOLUME UP */
- KEY_VOLUMEDOWN, /* 0x15: VOLUME DOWN */
- KEY_MUTE, /* 0x16: MUTE */
+ KEY_RESERVED, /* 0x14: VOLUME UP */
+ KEY_RESERVED, /* 0x15: VOLUME DOWN */
+ KEY_RESERVED, /* 0x16: MUTE */
KEY_VENDOR, /* 0x17: Thinkpad/AccessIBM/Lenovo */
/* (assignments unknown, please report if found) */
KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN,
KEY_RESERVED, /* 0x11: FN+PGUP (thinklight toggle) */
KEY_UNKNOWN, /* 0x12: FN+PGDOWN */
KEY_ZOOM, /* 0x13: FN+SPACE (zoom) */
- KEY_VOLUMEUP, /* 0x14: VOLUME UP */
- KEY_VOLUMEDOWN, /* 0x15: VOLUME DOWN */
- KEY_MUTE, /* 0x16: MUTE */
+ KEY_RESERVED, /* 0x14: VOLUME UP */
+ KEY_RESERVED, /* 0x15: VOLUME DOWN */
+ KEY_RESERVED, /* 0x16: MUTE */
KEY_VENDOR, /* 0x17: Thinkpad/AccessIBM/Lenovo */
/* (assignments unknown, please report if found) */
KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN,
return len;
}
- res = mutex_lock_interruptible(&hotkey_mutex);
- if (res < 0)
- return res;
+ if (mutex_lock_interruptible(&hotkey_mutex))
+ return -ERESTARTSYS;
res = hotkey_get(&status, &mask);
mutex_unlock(&hotkey_mutex);
if (res)
if (!tp_features.hotkey)
return -ENODEV;
- res = mutex_lock_interruptible(&hotkey_mutex);
- if (res < 0)
- return res;
+ if (mutex_lock_interruptible(&hotkey_mutex))
+ return -ERESTARTSYS;
res = hotkey_get(&status, &mask);
if (res)
static struct mutex brightness_mutex;
+static int __init tpacpi_query_bcll_levels(acpi_handle handle)
+{
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ union acpi_object *obj;
+ int rc;
+
+ if (ACPI_SUCCESS(acpi_evaluate_object(handle, NULL, NULL, &buffer))) {
+ obj = (union acpi_object *)buffer.pointer;
+ if (!obj || (obj->type != ACPI_TYPE_PACKAGE)) {
+ printk(IBM_ERR "Unknown BCLL data, "
+ "please report this to %s\n", IBM_MAIL);
+ rc = 0;
+ } else {
+ rc = obj->package.count;
+ }
+ } else {
+ return 0;
+ }
+
+ kfree(buffer.pointer);
+ return rc;
+}
+
+static acpi_status __init brightness_find_bcll(acpi_handle handle, u32 lvl,
+ void *context, void **rv)
+{
+ char name[ACPI_PATH_SEGMENT_LENGTH];
+ struct acpi_buffer buffer = { sizeof(name), &name };
+
+ if (ACPI_SUCCESS(acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer)) &&
+ !strncmp("BCLL", name, sizeof(name) - 1)) {
+ if (tpacpi_query_bcll_levels(handle) == 16) {
+ *rv = handle;
+ return AE_CTRL_TERMINATE;
+ } else {
+ return AE_OK;
+ }
+ } else {
+ return AE_OK;
+ }
+}
+
+static int __init brightness_check_levels(void)
+{
+ int status;
+ void *found_node = NULL;
+
+ if (!vid_handle) {
+ IBM_ACPIHANDLE_INIT(vid);
+ }
+ if (!vid_handle)
+ return 0;
+
+ /* Search for a BCLL package with 16 levels */
+ status = acpi_walk_namespace(ACPI_TYPE_PACKAGE, vid_handle, 3,
+ brightness_find_bcll, NULL, &found_node);
+
+ return (ACPI_SUCCESS(status) && found_node != NULL);
+}
+
+static acpi_status __init brightness_find_bcl(acpi_handle handle, u32 lvl,
+ void *context, void **rv)
+{
+ char name[ACPI_PATH_SEGMENT_LENGTH];
+ struct acpi_buffer buffer = { sizeof(name), &name };
+
+ if (ACPI_SUCCESS(acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer)) &&
+ !strncmp("_BCL", name, sizeof(name) - 1)) {
+ *rv = handle;
+ return AE_CTRL_TERMINATE;
+ } else {
+ return AE_OK;
+ }
+}
+
+static int __init brightness_check_std_acpi_support(void)
+{
+ int status;
+ void *found_node = NULL;
+
+ if (!vid_handle) {
+ IBM_ACPIHANDLE_INIT(vid);
+ }
+ if (!vid_handle)
+ return 0;
+
+ /* Search for a _BCL method, but don't execute it */
+ status = acpi_walk_namespace(ACPI_TYPE_METHOD, vid_handle, 3,
+ brightness_find_bcl, NULL, &found_node);
+
+ return (ACPI_SUCCESS(status) && found_node != NULL);
+}
+
static int __init brightness_init(struct ibm_init_struct *iibm)
{
int b;
mutex_init(&brightness_mutex);
+ if (!brightness_enable) {
+ dbg_printk(TPACPI_DBG_INIT,
+ "brightness support disabled by module parameter\n");
+ return 1;
+ } else if (brightness_enable > 1) {
+ if (brightness_check_std_acpi_support()) {
+ printk(IBM_NOTICE
+ "standard ACPI backlight interface available, not loading native one...\n");
+ return 1;
+ }
+ }
+
if (!brightness_mode) {
if (thinkpad_id.vendor == PCI_VENDOR_ID_LENOVO)
brightness_mode = 2;
if (brightness_mode > 3)
return -EINVAL;
+ tp_features.bright_16levels =
+ thinkpad_id.vendor == PCI_VENDOR_ID_LENOVO &&
+ brightness_check_levels();
+
b = brightness_get(NULL);
if (b < 0)
return 1;
+ if (tp_features.bright_16levels)
+ printk(IBM_INFO "detected a 16-level brightness capable ThinkPad\n");
+
ibm_backlight_device = backlight_device_register(
TPACPI_BACKLIGHT_DEV_NAME, NULL, NULL,
&ibm_backlight_data);
}
vdbg_printk(TPACPI_DBG_INIT, "brightness is supported\n");
- ibm_backlight_device->props.max_brightness = 7;
+ ibm_backlight_device->props.max_brightness =
+ (tp_features.bright_16levels)? 15 : 7;
ibm_backlight_device->props.brightness = b;
backlight_update_status(ibm_backlight_device);
static int brightness_update_status(struct backlight_device *bd)
{
+ /* it is the backlight class's job (caller) to handle
+ * EINTR and other errors properly */
return brightness_set(
(bd->props.fb_blank == FB_BLANK_UNBLANK &&
bd->props.power == FB_BLANK_UNBLANK) ?
if (brightness_mode & 1) {
if (!acpi_ec_read(brightness_offset, &lec))
return -EIO;
- lec &= 7;
+ lec &= (tp_features.bright_16levels)? 0x0f : 0x07;
level = lec;
};
if (brightness_mode & 2) {
lcmos = (nvram_read_byte(TP_NVRAM_ADDR_BRIGHTNESS)
& TP_NVRAM_MASK_LEVEL_BRIGHTNESS)
>> TP_NVRAM_POS_LEVEL_BRIGHTNESS;
+ lcmos &= (tp_features.bright_16levels)? 0x0f : 0x07;
level = lcmos;
}
return level;
}
+/* May return EINTR which can always be mapped to ERESTARTSYS */
static int brightness_set(int value)
{
int cmos_cmd, inc, i, res;
int current_value;
- if (value > 7)
+ if (value > ((tp_features.bright_16levels)? 15 : 7))
return -EINVAL;
res = mutex_lock_interruptible(&brightness_mutex);
cmos_cmd = value > current_value ?
TP_CMOS_BRIGHTNESS_UP :
TP_CMOS_BRIGHTNESS_DOWN;
- inc = value > current_value ? 1 : -1;
+ inc = (value > current_value)? 1 : -1;
res = 0;
for (i = current_value; i != value; i += inc) {
if ((level = brightness_get(NULL)) < 0) {
len += sprintf(p + len, "level:\t\tunreadable\n");
} else {
- len += sprintf(p + len, "level:\t\t%d\n", level & 0x7);
+ len += sprintf(p + len, "level:\t\t%d\n", level);
len += sprintf(p + len, "commands:\tup, down\n");
len += sprintf(p + len, "commands:\tlevel <level>"
- " (<level> is 0-7)\n");
+ " (<level> is 0-%d)\n",
+ (tp_features.bright_16levels) ? 15 : 7);
}
return len;
static int brightness_write(char *buf)
{
int level;
- int new_level;
+ int rc;
char *cmd;
+ int max_level = (tp_features.bright_16levels) ? 15 : 7;
- while ((cmd = next_cmd(&buf))) {
- if ((level = brightness_get(NULL)) < 0)
- return level;
- level &= 7;
+ level = brightness_get(NULL);
+ if (level < 0)
+ return level;
+ while ((cmd = next_cmd(&buf))) {
if (strlencmp(cmd, "up") == 0) {
- new_level = level == 7 ? 7 : level + 1;
+ if (level < max_level)
+ level++;
} else if (strlencmp(cmd, "down") == 0) {
- new_level = level == 0 ? 0 : level - 1;
- } else if (sscanf(cmd, "level %d", &new_level) == 1 &&
- new_level >= 0 && new_level <= 7) {
- /* new_level set */
+ if (level > 0)
+ level--;
+ } else if (sscanf(cmd, "level %d", &level) == 1 &&
+ level >= 0 && level <= max_level) {
+ /* new level set */
} else
return -EINVAL;
-
- brightness_set(new_level);
}
- return 0;
+ /*
+ * Now we know what the final level should be, so we try to set it.
+ * Doing it this way makes the syscall restartable in case of EINTR
+ */
+ rc = brightness_set(level);
+ return (rc == -EINTR)? ERESTARTSYS : rc;
}
static struct ibm_struct brightness_driver_data = {
/* scale down from 0-255 to 0-7 */
newlevel = (s >> 5) & 0x07;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = fan_get_status(&status);
if (!rc && (status &
int rc;
u8 s;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = fan_get_status(&s);
if (!rc)
fan_update_desired_level(s);
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
if (level == TPACPI_FAN_LAST_LEVEL)
level = fan_control_desired_level;
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
switch (fan_control_access_mode) {
case TPACPI_FAN_WR_ACPI_FANS:
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = 0;
switch (fan_control_access_mode) {
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = 0;
switch (fan_control_access_mode) {
unsigned int i;
struct ibm_struct *ibm;
+ if (!kp || !kp->name || !val)
+ return -EINVAL;
+
for (i = 0; i < ARRAY_SIZE(ibms_init); i++) {
ibm = ibms_init[i].data;
- BUG_ON(ibm == NULL);
+ WARN_ON(ibm == NULL);
+
+ if (!ibm || !ibm->name)
+ continue;
if (strcmp(ibm->name, kp->name) == 0 && ibm->write) {
if (strlen(val) > sizeof(ibms_init[i].param) - 2)
static int brightness_mode;
module_param_named(brightness_mode, brightness_mode, int, 0);
+static unsigned int brightness_enable = 2; /* 2 = auto, 0 = no, 1 = yes */
+module_param(brightness_enable, uint, 0);
+
static unsigned int hotkey_report_mode;
module_param(hotkey_report_mode, uint, 0);
/* ThinkPad CMOS NVRAM constants */
#define TP_NVRAM_ADDR_BRIGHTNESS 0x5e
-#define TP_NVRAM_MASK_LEVEL_BRIGHTNESS 0x07
+#define TP_NVRAM_MASK_LEVEL_BRIGHTNESS 0x0f
#define TP_NVRAM_POS_LEVEL_BRIGHTNESS 0
#define onoff(status,bit) ((status) & (1 << (bit)) ? "on" : "off")
u32 hotkey_wlsw:1;
u32 light:1;
u32 light_status:1;
+ u32 bright_16levels:1;
u32 wan:1;
u32 fan_ctrl_status_undef:1;
u32 input_device_registered:1;
static struct backlight_device *ibm_backlight_device;
static int brightness_offset = 0x31;
static int brightness_mode;
+static unsigned int brightness_enable; /* 0 = no, 1 = yes, 2 = auto */
static int brightness_init(struct ibm_init_struct *iibm);
static void brightness_exit(void);
* max 8 partitions per card
*/
#define MMC_SHIFT 3
+#define MMC_NUM_MINORS (256 >> MMC_SHIFT)
+
+static unsigned long dev_use[MMC_NUM_MINORS/(8*sizeof(unsigned long))];
/*
* There is one mmc_blk_data per slot.
mutex_lock(&open_lock);
md->usage--;
if (md->usage == 0) {
+ int devidx = md->disk->first_minor >> MMC_SHIFT;
+ __clear_bit(devidx, dev_use);
+
put_disk(md->disk);
kfree(md);
}
req->rq_disk->disk_name, err);
goto cmd_err;
}
- } while (!(cmd.resp[0] & R1_READY_FOR_DATA));
+ /*
+ * Some cards mishandle the status bits,
+ * so make sure to check both the busy
+ * indication and the card state.
+ */
+ } while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
+ (R1_CURRENT_STATE(cmd.resp[0]) == 7));
#if 0
if (cmd.resp[0] & ~0x00000900)
return 0;
}
-#define MMC_NUM_MINORS (256 >> MMC_SHIFT)
-
-static unsigned long dev_use[MMC_NUM_MINORS/(8*sizeof(unsigned long))];
static inline int mmc_blk_readonly(struct mmc_card *card)
{
struct mmc_blk_data *md = mmc_get_drvdata(card);
if (md) {
- int devidx;
-
/* Stop new requests from getting into the queue */
del_gendisk(md->disk);
/* Then flush out any already in there */
mmc_cleanup_queue(&md->queue);
- devidx = md->disk->first_minor >> MMC_SHIFT;
- __clear_bit(devidx, dev_use);
-
mmc_blk_put(md);
}
mmc_set_drvdata(card, NULL);
blk_queue_max_hw_segments(mq->queue, host->max_hw_segs);
blk_queue_max_segment_size(mq->queue, host->max_seg_size);
- mq->sg = kzalloc(sizeof(struct scatterlist) *
+ mq->sg = kmalloc(sizeof(struct scatterlist) *
host->max_phys_segs, GFP_KERNEL);
if (!mq->sg) {
ret = -ENOMEM;
goto cleanup_queue;
}
+ sg_init_table(mq->sg, host->max_phys_segs);
}
init_MUTEX(&mq->thread_sem);
#include <linux/mmc/host.h>
#include <linux/highmem.h>
#include <linux/scatterlist.h>
-#include <linux/log2.h>
#include <asm/io.h>
#define DRIVER_NAME "tifm_sd"
goto err_out;
}
- if (mrq->data && !is_power_of_2(mrq->data->blksz)) {
- printk(KERN_ERR "%s: Unsupported block size (%d bytes)\n",
- sock->dev.bus_id, mrq->data->blksz);
- mrq->cmd->error = -EINVAL;
- goto err_out;
- }
-
host->cmd_flags = 0;
host->block_pos = 0;
host->sg_pos = 0;
+ if (mrq->data && !is_power_of_2(mrq->data->blksz))
+ host->no_dma = 1;
+ else
+ host->no_dma = no_dma ? 1 : 0;
+
if (r_data) {
tifm_sd_set_data_timeout(host, r_data);
: PCI_DMA_FROMDEVICE)) {
printk(KERN_ERR "%s : scatterlist map failed\n",
sock->dev.bus_id);
- spin_unlock_irqrestore(&sock->lock, flags);
+ mrq->cmd->error = -ENOMEM;
goto err_out;
}
host->sg_len = tifm_map_sg(sock, r_data->sg,
r_data->flags & MMC_DATA_WRITE
? PCI_DMA_TODEVICE
: PCI_DMA_FROMDEVICE);
- spin_unlock_irqrestore(&sock->lock, flags);
+ mrq->cmd->error = -ENOMEM;
goto err_out;
}
return -ENOMEM;
host = mmc_priv(mmc);
- host->no_dma = no_dma;
tifm_set_drvdata(sock, mmc);
host->dev = sock;
host->timeout_jiffies = msecs_to_jiffies(1000);
if (!is_valid_ether_addr(dev->dev_addr)) {
/* Grab the MAC from the board somehow - this is done in the
arch/blackfin/mach-bf537/boards/eth_mac.c */
- get_bf537_ether_addr(dev->dev_addr);
+ bfin_get_ether_addr(dev->dev_addr);
}
/* If still not valid, get a random one */
struct mii_bus mii_bus;
};
-extern void get_bf537_ether_addr(char *addr);
+extern void bfin_get_ether_addr(char *addr);
struct mlx4_cmd_mailbox *mailbox;
int ret = 0;
- if (cur_state >= MLX4_QP_NUM_STATE || cur_state >= MLX4_QP_NUM_STATE ||
+ if (cur_state >= MLX4_QP_NUM_STATE || new_state >= MLX4_QP_NUM_STATE ||
!op[cur_state][new_state])
return -EINVAL;
case PLIP_PK_DONE:
/* Inform the upper layer for the arrival of a packet. */
rcv->skb->protocol=plip_type_trans(rcv->skb, dev);
- netif_rx(rcv->skb);
+ netif_rx_ni(rcv->skb);
dev->last_rx = jiffies;
dev->stats.rx_bytes += rcv->length.h;
dev->stats.rx_packets++;
nl = netdev_priv(dev);
nl->dev = dev;
- nl->pardev = parport_register_device(port, name, plip_preempt,
+ nl->pardev = parport_register_device(port, dev->name, plip_preempt,
plip_wakeup, plip_interrupt,
0, dev);
if (vi->num < vi->max / 2)
try_fill_recv(vi);
- /* All done? */
- if (!skb) {
+ /* Out of packets? */
+ if (received < budget) {
netif_rx_complete(vi->dev, napi);
if (unlikely(!vi->rvq->vq_ops->restart(vi->rvq))
&& netif_rx_reschedule(vi->dev, napi))
static void virtnet_remove(struct virtio_device *vdev)
{
- unregister_netdev(vdev->priv);
- free_netdev(vdev->priv);
+ struct virtnet_info *vi = vdev->priv;
+
+ vdev->config->del_vq(vi->svq);
+ vdev->config->del_vq(vi->rvq);
+ unregister_netdev(vi->dev);
+ free_netdev(vi->dev);
}
static struct virtio_device_id id_table[] = {
}
static int rt2500usb_get_tx_data_len(struct rt2x00_dev *rt2x00dev,
- int maxpacket, struct sk_buff *skb)
+ struct sk_buff *skb)
{
int length;
* but it must _not_ be a multiple of the USB packet size.
*/
length = roundup(skb->len, 2);
- length += (2 * !(length % maxpacket));
+ length += (2 * !(length % rt2x00dev->usb_maxpacket));
return length;
}
struct data_entry *beacon;
struct data_entry *guardian;
int pipe = usb_sndbulkpipe(usb_dev, 1);
- int max_packet = usb_maxpacket(usb_dev, pipe, 1);
int length;
/*
ring->desc_size),
skb->len - ring->desc_size, control);
- length = rt2500usb_get_tx_data_len(rt2x00dev, max_packet, skb);
+ length = rt2500usb_get_tx_data_len(rt2x00dev, skb);
usb_fill_bulk_urb(beacon->priv, usb_dev, pipe,
skb->data, length, rt2500usb_beacondone, beacon);
int (*write_tx_data) (struct rt2x00_dev *rt2x00dev,
struct data_ring *ring, struct sk_buff *skb,
struct ieee80211_tx_control *control);
- int (*get_tx_data_len) (struct rt2x00_dev *rt2x00dev, int maxpacket,
+ int (*get_tx_data_len) (struct rt2x00_dev *rt2x00dev,
struct sk_buff *skb);
void (*kick_tx_queue) (struct rt2x00_dev *rt2x00dev,
unsigned int queue);
*/
u32 *rf;
+ /*
+ * USB Max frame size (for rt2500usb & rt73usb).
+ */
+ u16 usb_maxpacket;
+
/*
* Current TX power value.
*/
interface_to_usbdev(rt2x00dev_usb(rt2x00dev));
struct data_entry *entry = rt2x00_get_data_entry(ring);
int pipe = usb_sndbulkpipe(usb_dev, 1);
- int max_packet = usb_maxpacket(usb_dev, pipe, 1);
u32 length;
if (rt2x00_ring_full(ring)) {
* length of the data to usb_fill_bulk_urb. Pass the skb
* to the driver to determine what the length should be.
*/
- length = rt2x00dev->ops->lib->get_tx_data_len(rt2x00dev,
- max_packet, skb);
+ length = rt2x00dev->ops->lib->get_tx_data_len(rt2x00dev, skb);
/*
* Initialize URB and send the frame to the device.
rt2x00dev->ops = ops;
rt2x00dev->hw = hw;
+ rt2x00dev->usb_maxpacket =
+ usb_maxpacket(usb_dev, usb_sndbulkpipe(usb_dev, 1), 1);
+ if (!rt2x00dev->usb_maxpacket)
+ rt2x00dev->usb_maxpacket = 1;
+
retval = rt2x00usb_alloc_reg(rt2x00dev);
if (retval)
goto exit_free_device;
}
static int rt73usb_get_tx_data_len(struct rt2x00_dev *rt2x00dev,
- int maxpacket, struct sk_buff *skb)
+ struct sk_buff *skb)
{
int length;
* but it must _not_ be a multiple of the USB packet size.
*/
length = roundup(skb->len, 4);
- length += (4 * !(length % maxpacket));
+ length += (4 * !(length % rt2x00dev->usb_maxpacket));
return length;
}
{
int i = 0;
int irq;
+ int p, t;
if (!valid_IRQ(gsi))
return;
if (i >= PNP_MAX_IRQ)
return;
-#ifdef CONFIG_X86
- if (gsi < 16 && (triggering != ACPI_EDGE_SENSITIVE ||
- polarity != ACPI_ACTIVE_HIGH)) {
- pnp_warn("BIOS BUG: legacy PNP IRQ %d should be edge trigger, "
- "active high", gsi);
- triggering = ACPI_EDGE_SENSITIVE;
- polarity = ACPI_ACTIVE_HIGH;
+ /*
+ * in IO-APIC mode, use overrided attribute. Two reasons:
+ * 1. BIOS bug in DSDT
+ * 2. BIOS uses IO-APIC mode Interrupt Source Override
+ */
+ if (!acpi_get_override_irq(gsi, &t, &p)) {
+ t = t ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
+ p = p ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
+
+ if (triggering != t || polarity != p) {
+ pnp_warn("IRQ %d override to %s, %s",
+ gsi, t ? "edge":"level", p ? "low":"high");
+ triggering = t;
+ polarity = p;
+ }
}
-#endif
res->irq_resource[i].flags = IORESOURCE_IRQ; // Also clears _UNSET flag
res->irq_resource[i].flags |= irq_flags(triggering, polarity);
config RTC_DRV_BFIN
tristate "Blackfin On-Chip RTC"
- depends on BFIN
+ depends on BLACKFIN
help
If you say yes here you will get support for the
Blackfin On-Chip Real Time Clock.
void css_schedule_reprobe(void)
{
need_reprobe = 1;
- queue_work(ccw_device_work, &css_reprobe_work);
+ queue_work(slow_path_wq, &css_reprobe_work);
}
EXPORT_SYMBOL_GPL(css_schedule_reprobe);
if (sch->schib.pmcw.dev != cdev->private->dev_id.devno) {
PREPARE_WORK(&cdev->private->kick_work,
ccw_device_move_to_orphanage);
- queue_work(ccw_device_work, &cdev->private->kick_work);
+ queue_work(slow_path_wq, &cdev->private->kick_work);
} else
ccw_device_start_id(cdev, 0);
}
{
struct subchannel *sch;
struct ccw1 *ccw;
- int ret;
sch = to_subchannel(cdev->dev.parent);
/* Setup sense channel program. */
ccw = cdev->private->iccws;
- if (sch->schib.pmcw.pim != 0x80) {
- /* more than one path installed. */
- ccw->cmd_code = CCW_CMD_SUSPEND_RECONN;
- ccw->cda = 0;
- ccw->count = 0;
- ccw->flags = CCW_FLAG_SLI | CCW_FLAG_CC;
- ccw++;
- }
ccw->cmd_code = CCW_CMD_SENSE_ID;
ccw->cda = (__u32) __pa (&cdev->private->senseid);
ccw->count = sizeof (struct senseid);
/* Reset device status. */
memset(&cdev->private->irb, 0, sizeof(struct irb));
+ cdev->private->flags.intretry = 0;
- /* Try on every path. */
- ret = -ENODEV;
- while (cdev->private->imask != 0) {
- if ((sch->opm & cdev->private->imask) != 0 &&
- cdev->private->iretry > 0) {
- cdev->private->iretry--;
- /* Reset internal retry indication. */
- cdev->private->flags.intretry = 0;
- ret = cio_start (sch, cdev->private->iccws,
- cdev->private->imask);
- /* ret is 0, -EBUSY, -EACCES or -ENODEV */
- if (ret != -EACCES)
- return ret;
- }
- cdev->private->imask >>= 1;
- cdev->private->iretry = 5;
- }
- return ret;
+ return cio_start(sch, ccw, LPM_ANYPATH);
}
void
memset (&cdev->private->senseid, 0, sizeof (struct senseid));
cdev->private->senseid.cu_type = 0xFFFF;
- cdev->private->imask = 0x80;
- cdev->private->iretry = 5;
+ cdev->private->iretry = 3;
ret = __ccw_device_sense_id_start(cdev);
if (ret && ret != -EBUSY)
ccw_device_sense_id_done(cdev, ret);
ccw_device_sense_id_done(cdev, ret);
break;
case -EACCES: /* channel is not operational. */
- sch->lpm &= ~cdev->private->imask;
- cdev->private->imask >>= 1;
- cdev->private->iretry = 5;
- /* fall through. */
case -EAGAIN: /* try again. */
- ret = __ccw_device_sense_id_start(cdev);
- if (ret == 0 || ret == -EBUSY)
- break;
+ cdev->private->iretry--;
+ if (cdev->private->iretry > 0) {
+ ret = __ccw_device_sense_id_start(cdev);
+ if (ret == 0 || ret == -EBUSY)
+ break;
+ }
/* fall through. */
default: /* Sense ID failed. Try asking VM. */
if (MACHINE_IS_VM) {
}
}
-static void hexdump(u8 *x, int len)
-{
- int i;
-
- printk("[ ");
- for (i = 0; i < len; i++)
- printk("%x ", x[i]);
- printk("]\n");
-}
-
static int idescsi_check_condition(ide_drive_t *drive, struct request *failed_command)
{
idescsi_scsi_t *scsi = drive_to_idescsi(drive);
pc->scsi_cmd = ((idescsi_pc_t *) failed_command->special)->scsi_cmd;
if (test_bit(IDESCSI_LOG_CMD, &scsi->log)) {
printk ("ide-scsi: %s: queue cmd = ", drive->name);
- hexdump(pc->c, 6);
+ print_hex_dump(KERN_CONT, "", DUMP_PREFIX_NONE, 16, 1, pc->c,
+ 6, 0);
}
rq->rq_disk = scsi->disk;
return ide_do_drive_cmd(drive, rq, ide_preempt);
idescsi_pc_t *opc = (idescsi_pc_t *) rq->buffer;
if (log) {
printk ("ide-scsi: %s: wrap up check %lu, rst = ", drive->name, opc->scsi_cmd->serial_number);
- hexdump(pc->buffer,16);
+ print_hex_dump(KERN_CONT, "", DUMP_PREFIX_NONE, 16, 1,
+ pc->buffer, 16, 0);
}
memcpy((void *) opc->scsi_cmd->sense_buffer, pc->buffer, SCSI_SENSE_BUFFERSIZE);
kfree(pc->buffer);
if (test_bit(IDESCSI_LOG_CMD, &scsi->log)) {
printk ("ide-scsi: %s: que %lu, cmd = ", drive->name, cmd->serial_number);
- hexdump(cmd->cmnd, cmd->cmd_len);
+ print_hex_dump(KERN_CONT, "", DUMP_PREFIX_NONE, 16, 1,
+ cmd->cmnd, cmd->cmd_len, 0);
if (memcmp(pc->c, cmd->cmnd, cmd->cmd_len)) {
printk ("ide-scsi: %s: que %lu, tsl = ", drive->name, cmd->serial_number);
- hexdump(pc->c, 12);
+ print_hex_dump(KERN_CONT, "", DUMP_PREFIX_NONE, 16, 1,
+ pc->c, 12, 0);
}
}
config SERIAL_BFIN
tristate "Blackfin serial port support"
- depends on BFIN
+ depends on BLACKFIN
select SERIAL_CORE
select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
help
config SPI_BFIN
tristate "SPI controller driver for ADI Blackfin5xx"
- depends on SPI_MASTER && BFIN
+ depends on SPI_MASTER && BLACKFIN
help
This is the SPI controller master driver for Blackfin 5xx processor.
CHIP_DEF(PCI_CHIP_RV380_3154, RV380, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
CHIP_DEF(PCI_CHIP_RV370_5B60, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B62, RV380, CHIP_HAS_CRTC2),
+ CHIP_DEF(PCI_CHIP_RV370_5B63, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B64, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B65, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5460, RV380, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
config VGA_CONSOLE
bool "VGA text console" if EMBEDDED || !X86
- depends on !ARCH_ACORN && !ARCH_EBSA110 && !4xx && !8xx && !SPARC && !M68K && !PARISC && !FRV && !ARCH_VERSATILE && !SUPERH && !BFIN
+ depends on !ARCH_ACORN && !ARCH_EBSA110 && !4xx && !8xx && !SPARC && !M68K && !PARISC && !FRV && !ARCH_VERSATILE && !SUPERH && !BLACKFIN
default y
help
Saying Y here will allow you to use Linux in text mode through a
return err;
}
+static int virtio_dev_remove(struct device *_d)
+{
+ struct virtio_device *dev = container_of(_d,struct virtio_device,dev);
+ struct virtio_driver *drv = container_of(dev->dev.driver,
+ struct virtio_driver, driver);
+
+ dev->config->set_status(dev, dev->config->get_status(dev)
+ & ~VIRTIO_CONFIG_S_DRIVER);
+ drv->remove(dev);
+ return 0;
+}
+
int register_virtio_driver(struct virtio_driver *driver)
{
driver->driver.bus = &virtio_bus;
driver->driver.probe = virtio_dev_probe;
+ driver->driver.remove = virtio_dev_remove;
return driver_register(&driver->driver);
}
EXPORT_SYMBOL_GPL(register_virtio_driver);
}
+static int zorro_device_remove(struct device *dev)
+{
+ struct zorro_dev *z = to_zorro_dev(dev);
+ struct zorro_driver *drv = to_zorro_driver(dev->driver);
+
+ if (drv) {
+ if (drv->remove)
+ drv->remove(z);
+ z->driver = NULL;
+ }
+ return 0;
+}
+
+
/**
* zorro_register_driver - register a new Zorro driver
* @drv: the driver structure to register
.name = "zorro",
.match = zorro_bus_match,
.probe = zorro_device_probe,
+ .remove = zorro_device_remove,
};
This option will enlarge your kernel, but it allows debugging of
ocfs2 filesystem issues.
+config OCFS2_DEBUG_FS
+ bool "OCFS2 expensive checks"
+ depends on OCFS2_FS
+ default n
+ help
+ This option will enable expensive consistency checks. Enable
+ this option for debugging only as it is likely to decrease
+ performance of the filesystem.
+
config MINIX_FS
tristate "Minix fs support"
help
Version 1.52
------------
Fix oops on second mount to server when null auth is used.
+Enable experimental Kerberos support. Return writebehind errors on flush
+and sync so that events like out of disk space get reported properly on
+cached files.
Version 1.51
------------
Restrictions
============
-Servers must support the NTLM SMB dialect (which is the most recent, supported
-by Samba and Windows NT version 4, 2000 and XP and many other SMB/CIFS servers)
Servers must support either "pure-TCP" (port 445 TCP/IP CIFS connections) or RFC
-1001/1002 support for "Netbios-Over-TCP/IP." Neither of these is likely to be a
-problem as most servers support this. IPv6 support is planned for the future,
-and is almost complete.
+1001/1002 support for "Netbios-Over-TCP/IP." This is not likely to be a
+problem as most servers support this.
Valid filenames differ between Windows and Linux. Windows typically restricts
filenames which contain certain reserved characters (e.g.the character :
byte range locks).
remount remount the share (often used to change from ro to rw mounts
or vice versa)
+ cifsacl Report mode bits (e.g. on stat) based on the Windows ACL for
+ the file. (EXPERIMENTAL)
servern Specify the server 's netbios name (RFC1001 name) to use
when attempting to setup a session to the server. This is
This is needed for mounting to some older servers (such
performance enhancement was disabled when
signing turned on in case buffer was modified
just before it was sent, also this flag will
- be used to use the new experimental sessionsetup
- code).
+ be used to use the new experimental directory change
+ notification code).
These experimental features and tracing can be enabled by changing flags in
/proc/fs/cifs (after the cifs module has been installed or built into the
Two other experimental features are under development. To test these
requires enabling CONFIG_CIFS_EXPERIMENTAL
- ipv6 enablement
+ cifsacl support needed to retrieve approximated mode bits based on
+ the contents on the CIFS ACL.
DNOTIFY fcntl: needed for support of directory change
notification and perhaps later for file leases)
returned success.
Also note that "cat /proc/fs/cifs/DebugData" will display information about
-the active sessions and the shares that are mounted. Note: NTLMv2 enablement
-will not work since its implementation is not quite complete yet. Do not alter
-the ExtendedSecurity configuration value unless you are doing specific testing.
-Enabling extended security works to Windows 2000 Workstations and XP but not to
-Windows 2000 server or Samba since it does not usually send "raw NTLMSSP"
-(instead it sends NTLMSSP encapsulated in SPNEGO/GSSAPI, which support is not
-complete in the CIFS VFS yet).
+the active sessions and the shares that are mounted.
+Enabling Kerberos (extended security) works when CONFIG_CIFS_EXPERIMENTAL is enabled
+but requires a user space helper (from the Samba project). NTLM and NTLMv2 and
+LANMAN support do not require this helpr.
c) Better pam/winbind integration (e.g. to handle uid mapping
better)
-d) Kerberos/SPNEGO session setup support - (started)
+d) Verify that Kerberos signing works
e) Cleanup now unneeded SessSetup code in
fs/cifs/connect.c and add back in NTLMSSP code if any servers
.describe = user_describe,
};
+#define MAX_VER_STR_LEN 9 /* length of longest version string e.g.
+ strlen(";ver=0xFF") */
+#define MAX_MECH_STR_LEN 13 /* length of longest security mechanism name, eg
+ in future could have strlen(";sec=ntlmsspi") */
+#define MAX_IPV6_ADDR_LEN 42 /* eg FEDC:BA98:7654:3210:FEDC:BA98:7654:3210/60 */
/* get a key struct with a SPNEGO security blob, suitable for session setup */
struct key *
-cifs_get_spnego_key(struct cifsSesInfo *sesInfo, const char *hostname)
+cifs_get_spnego_key(struct cifsSesInfo *sesInfo)
{
struct TCP_Server_Info *server = sesInfo->server;
char *description, *dp;
size_t desc_len;
struct key *spnego_key;
+ const char *hostname = server->hostname;
-
- /* version + ;ip{4|6}= + address + ;host=hostname +
- ;sec= + ;uid= + NULL */
- desc_len = 4 + 5 + 32 + 1 + 5 + strlen(hostname) +
- strlen(";sec=krb5") + 7 + sizeof(uid_t)*2 + 1;
+ /* BB: come up with better scheme for determining length */
+ /* length of fields (with semicolons): ver=0xyz ipv4= ipaddress host=
+ hostname sec=mechanism uid=0x uid */
+ desc_len = MAX_VER_STR_LEN + 5 + MAX_IPV6_ADDR_LEN + 1 + 6 +
+ strlen(hostname) + MAX_MECH_STR_LEN + 8 + (sizeof(uid_t) * 2);
spnego_key = ERR_PTR(-ENOMEM);
description = kzalloc(desc_len, GFP_KERNEL);
if (description == NULL)
dp = description;
/* start with version and hostname portion of UNC string */
spnego_key = ERR_PTR(-EINVAL);
- sprintf(dp, "0x%2.2x;host=%s;", CIFS_SPNEGO_UPCALL_VERSION,
+ sprintf(dp, "ver=0x%x;host=%s;", CIFS_SPNEGO_UPCALL_VERSION,
hostname);
dp = description + strlen(description);
#ifdef __KERNEL__
extern struct key_type cifs_spnego_key_type;
+extern struct key *cifs_get_spnego_key(struct cifsSesInfo *sesInfo);
#endif /* KERNEL */
#endif /* _CIFS_SPNEGO_H */
/* BB need to add parm so we can store the SID BB */
+ if (!pdacl) {
+ /* no DACL in the security descriptor, set
+ all the permissions for user/group/other */
+ inode->i_mode |= S_IRWXUGO;
+ return;
+ }
+
/* validate that we do not go past end of acl */
if (end_of_acl < (char *)pdacl + le16_to_cpu(pdacl->size)) {
cERROR(1, ("ACL too small to parse DACL"));
user/group/other have no permissions */
inode->i_mode &= ~(S_IRWXUGO);
- if (!pdacl) {
- /* no DACL in the security descriptor, set
- all the permissions for user/group/other */
- inode->i_mode |= S_IRWXUGO;
- return;
- }
acl_base = (char *)pdacl;
acl_size = sizeof(struct cifs_acl);
cifs_inode->cifsAttrs = 0x20; /* default */
atomic_set(&cifs_inode->inUse, 0);
cifs_inode->time = 0;
+ cifs_inode->write_behind_rc = 0;
/* Until the file is open and we have gotten oplock
info back from the server, can not assume caching of
file data or metadata */
struct cifsTconInfo *pTcon;
struct inode *inode;
__u16 netfid;
- int rc;
+ int rc, waitrc = 0;
set_freezable();
do {
filemap_fdatawrite(inode->i_mapping);
if (CIFS_I(inode)->clientCanCacheRead
== 0) {
- filemap_fdatawait(inode->i_mapping);
+ waitrc = filemap_fdatawait(inode->i_mapping);
invalidate_remote_inode(inode);
}
+ if (rc == 0)
+ rc = waitrc;
} else
rc = 0;
/* mutex_unlock(&inode->i_mutex);*/
unsigned int len;
union {
char ntlm[CIFS_SESS_KEY_SIZE + 16];
+ char krb5[CIFS_SESS_KEY_SIZE + 16]; /* BB: length correct? */
struct {
char key[16];
struct ntlmv2_resp resp;
/* 15 character server name + 0x20 16th byte indicating type = srv */
char server_RFC1001_name[SERVER_NAME_LEN_WITH_NULL];
char unicode_server_Name[SERVER_NAME_LEN_WITH_NULL * 2];
+ char *hostname; /* hostname portion of UNC string */
struct socket *ssocket;
union {
struct sockaddr_in sockAddr;
#define CIFS_LARGE_BUFFER 2
#define CIFS_IOVEC 4 /* array of response buffers */
+/* Type of Request to SendReceive2 */
+#define CIFS_STD_OP 0 /* normal request timeout */
+#define CIFS_LONG_OP 1 /* long op (up to 45 sec, oplock time) */
+#define CIFS_VLONG_OP 2 /* sloow op - can take up to 180 seconds */
+#define CIFS_BLOCKING_OP 4 /* operation can block */
+#define CIFS_ASYNC_OP 8 /* do not wait for response */
+#define CIFS_TIMEOUT_MASK 0x00F /* only one of 5 above set in req */
+#define CIFS_LOG_ERROR 0x010 /* log NT STATUS if non-zero */
+#define CIFS_LARGE_BUF_OP 0x020 /* large request buffer */
+#define CIFS_NO_RESP 0x040 /* no response buffer required */
+
/* Security Flags: indicate type of session setup needed */
#define CIFSSEC_MAY_SIGN 0x00001
#define CIFSSEC_MAY_NTLM 0x00002
struct smb_hdr * /* input */ ,
struct smb_hdr * /* out */ ,
int * /* bytes returned */ , const int long_op);
+extern int SendReceiveNoRsp(const unsigned int xid, struct cifsSesInfo *ses,
+ struct smb_hdr *in_buf, int flags);
extern int SendReceive2(const unsigned int /* xid */ , struct cifsSesInfo *,
struct kvec *, int /* nvec to send */,
- int * /* type of buf returned */ , const int long_op,
- const int logError /* whether to log status code*/ );
+ int * /* type of buf returned */ , const int flags);
extern int SendReceiveBlockingLock(const unsigned int /* xid */ ,
struct cifsTconInfo *,
struct smb_hdr * /* input */ ,
extern int small_smb_init_no_tc(const int smb_cmd, const int wct,
struct cifsSesInfo *ses,
void **request_buf);
-extern struct key *cifs_get_spnego_key(struct cifsSesInfo *sesInfo,
- const char *hostname);
extern int CIFS_SessSetup(unsigned int xid, struct cifsSesInfo *ses,
const int stage,
const struct nls_table *nls_cp);
extern int CIFSSMBOpen(const int xid, struct cifsTconInfo *tcon,
const char *fileName, const int disposition,
const int access_flags, const int omode,
- __u16 * netfid, int *pOplock, FILE_ALL_INFO *,
+ __u16 *netfid, int *pOplock, FILE_ALL_INFO *,
const struct nls_table *nls_codepage, int remap);
extern int SMBLegacyOpen(const int xid, struct cifsTconInfo *tcon,
const char *fileName, const int disposition,
const int access_flags, const int omode,
- __u16 * netfid, int *pOplock, FILE_ALL_INFO *,
+ __u16 *netfid, int *pOplock, FILE_ALL_INFO *,
const struct nls_table *nls_codepage, int remap);
extern int CIFSPOSIXCreate(const int xid, struct cifsTconInfo *tcon,
- u32 posix_flags, __u64 mode, __u16 * netfid,
+ u32 posix_flags, __u64 mode, __u16 *netfid,
FILE_UNIX_BASIC_INFO *pRetData,
__u32 *pOplock, const char *name,
const struct nls_table *nls_codepage, int remap);
const __u64 offset, unsigned int *nbytes,
struct kvec *iov, const int nvec, const int long_op);
extern int CIFSGetSrvInodeNumber(const int xid, struct cifsTconInfo *tcon,
- const unsigned char *searchName, __u64 * inode_number,
+ const unsigned char *searchName, __u64 *inode_number,
const struct nls_table *nls_codepage,
int remap_special_chars);
extern int cifs_convertUCSpath(char *target, const __le16 *source, int maxlen,
const char *local_acl, const int buflen, const int acl_type,
const struct nls_table *nls_codepage, int remap_special_chars);
extern int CIFSGetExtAttr(const int xid, struct cifsTconInfo *tcon,
- const int netfid, __u64 * pExtAttrBits, __u64 *pMask);
+ const int netfid, __u64 *pExtAttrBits, __u64 *pMask);
#endif /* _CIFSPROTO_H */
CIFSSMBTDis(const int xid, struct cifsTconInfo *tcon)
{
struct smb_hdr *smb_buffer;
- struct smb_hdr *smb_buffer_response; /* BB removeme BB */
int rc = 0;
- int length;
cFYI(1, ("In tree disconnect"));
/*
if (rc) {
up(&tcon->tconSem);
return rc;
- } else {
- smb_buffer_response = smb_buffer; /* BB removeme BB */
}
- rc = SendReceive(xid, tcon->ses, smb_buffer, smb_buffer_response,
- &length, 0);
+
+ rc = SendReceiveNoRsp(xid, tcon->ses, smb_buffer, 0);
if (rc)
cFYI(1, ("Tree disconnect failed %d", rc));
- if (smb_buffer)
- cifs_small_buf_release(smb_buffer);
up(&tcon->tconSem);
/* No need to return error on this operation if tid invalidated and
int
CIFSSMBLogoff(const int xid, struct cifsSesInfo *ses)
{
- struct smb_hdr *smb_buffer_response;
LOGOFF_ANDX_REQ *pSMB;
int rc = 0;
- int length;
cFYI(1, ("In SMBLogoff for session disconnect"));
if (ses)
return rc;
}
- smb_buffer_response = (struct smb_hdr *)pSMB; /* BB removeme BB */
-
if (ses->server) {
pSMB->hdr.Mid = GetNextMid(ses->server);
pSMB->hdr.Uid = ses->Suid;
pSMB->AndXCommand = 0xFF;
- rc = SendReceive(xid, ses, (struct smb_hdr *) pSMB,
- smb_buffer_response, &length, 0);
+ rc = SendReceiveNoRsp(xid, ses, (struct smb_hdr *) pSMB, 0);
if (ses->server) {
atomic_dec(&ses->server->socketUseCount);
if (atomic_read(&ses->server->socketUseCount) == 0) {
}
}
up(&ses->sesSem);
- cifs_small_buf_release(pSMB);
/* if session dead then we do not need to do ulogoff,
since server closed smb session, no sense reporting
pSMB->ByteCount = cpu_to_le16(count);
/* long_op set to 1 to allow for oplock break timeouts */
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 1);
+ (struct smb_hdr *)pSMBr, &bytes_returned, CIFS_LONG_OP);
cifs_stats_inc(&tcon->num_opens);
if (rc) {
cFYI(1, ("Error in Open = %d", rc));
pSMB->ByteCount = cpu_to_le16(count);
/* long_op set to 1 to allow for oplock break timeouts */
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 1);
+ (struct smb_hdr *)pSMBr, &bytes_returned, CIFS_LONG_OP);
cifs_stats_inc(&tcon->num_opens);
if (rc) {
cFYI(1, ("Error in Open = %d", rc));
iov[0].iov_base = (char *)pSMB;
iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovecs */,
- &resp_buf_type, 0 /* not long op */, 1 /* log err */ );
+ &resp_buf_type, CIFS_STD_OP | CIFS_LOG_ERROR);
cifs_stats_inc(&tcon->num_reads);
pSMBr = (READ_RSP *)iov[0].iov_base;
if (rc) {
rc = SendReceive2(xid, tcon->ses, iov, n_vec + 1, &resp_buf_type,
- long_op, 0 /* do not log STATUS code */ );
+ long_op);
cifs_stats_inc(&tcon->num_writes);
if (rc) {
cFYI(1, ("Send error Write2 = %d", rc));
int timeout = 0;
__u16 count;
- cFYI(1, ("In CIFSSMBLock - timeout %d numLock %d", waitFlag, numLock));
+ cFYI(1, ("CIFSSMBLock timeout %d numLock %d", waitFlag, numLock));
rc = small_smb_init(SMB_COM_LOCKING_ANDX, 8, tcon, (void **) &pSMB);
if (rc)
pSMBr = (LOCK_RSP *)pSMB; /* BB removeme BB */
if (lockType == LOCKING_ANDX_OPLOCK_RELEASE) {
- timeout = -1; /* no response expected */
+ timeout = CIFS_ASYNC_OP; /* no response expected */
pSMB->Timeout = 0;
} else if (waitFlag == TRUE) {
- timeout = 3; /* blocking operation, no timeout */
+ timeout = CIFS_BLOCKING_OP; /* blocking operation, no timeout */
pSMB->Timeout = cpu_to_le32(-1);/* blocking - do not time out */
} else {
pSMB->Timeout = 0;
if (waitFlag) {
rc = SendReceiveBlockingLock(xid, tcon, (struct smb_hdr *) pSMB,
(struct smb_hdr *) pSMBr, &bytes_returned);
+ cifs_small_buf_release(pSMB);
} else {
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, timeout);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *)pSMB,
+ timeout);
+ /* SMB buffer freed by function above */
}
cifs_stats_inc(&tcon->num_locks);
if (rc) {
cFYI(1, ("Send error in Lock = %d", rc));
}
- cifs_small_buf_release(pSMB);
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
int rc = 0;
int timeout = 0;
int bytes_returned = 0;
+ int resp_buf_type = 0;
__u16 params, param_offset, offset, byte_count, count;
+ struct kvec iov[1];
cFYI(1, ("Posix Lock"));
parm_data->lock_type = cpu_to_le16(lock_type);
if (waitFlag) {
- timeout = 3; /* blocking operation, no timeout */
+ timeout = CIFS_BLOCKING_OP; /* blocking operation, no timeout */
parm_data->lock_flags = cpu_to_le16(1);
pSMB->Timeout = cpu_to_le32(-1);
} else
rc = SendReceiveBlockingLock(xid, tcon, (struct smb_hdr *) pSMB,
(struct smb_hdr *) pSMBr, &bytes_returned);
} else {
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, timeout);
+ iov[0].iov_base = (char *)pSMB;
+ iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
+ rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovecs */,
+ &resp_buf_type, timeout);
+ pSMB = NULL; /* request buf already freed by SendReceive2. Do
+ not try to free it twice below on exit */
+ pSMBr = (struct smb_com_transaction2_sfi_rsp *)iov[0].iov_base;
}
if (rc) {
if (pSMB)
cifs_small_buf_release(pSMB);
+ if (resp_buf_type == CIFS_SMALL_BUFFER)
+ cifs_small_buf_release(iov[0].iov_base);
+ else if (resp_buf_type == CIFS_LARGE_BUFFER)
+ cifs_buf_release(iov[0].iov_base);
+
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
{
int rc = 0;
CLOSE_REQ *pSMB = NULL;
- CLOSE_RSP *pSMBr = NULL;
- int bytes_returned;
cFYI(1, ("In CIFSSMBClose"));
/* do not retry on dead session on close */
if (rc)
return rc;
- pSMBr = (CLOSE_RSP *)pSMB; /* BB removeme BB */
-
pSMB->FileID = (__u16) smb_file_id;
pSMB->LastWriteTime = 0xFFFFFFFF;
pSMB->ByteCount = 0;
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
cifs_stats_inc(&tcon->num_closes);
if (rc) {
if (rc != -EINTR) {
}
}
- cifs_small_buf_release(pSMB);
-
/* Since session is dead, file will be closed on server already */
if (rc == -EAGAIN)
rc = 0;
iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovec */, &buf_type,
- 0 /* not long op */, 0 /* do not log STATUS codes */ );
+ CIFS_STD_OP);
cifs_stats_inc(&tcon->num_acl_get);
if (rc) {
cFYI(1, ("Send error in QuerySecDesc = %d", rc));
{
int rc = 0;
FINDCLOSE_REQ *pSMB = NULL;
- CLOSE_RSP *pSMBr = NULL; /* BB removeme BB */
- int bytes_returned;
cFYI(1, ("In CIFSSMBFindClose"));
rc = small_smb_init(SMB_COM_FIND_CLOSE2, 1, tcon, (void **)&pSMB);
if (rc)
return rc;
- pSMBr = (CLOSE_RSP *)pSMB; /* BB removeme BB */
pSMB->FileID = searchHandle;
pSMB->ByteCount = 0;
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cERROR(1, ("Send error in FindClose = %d", rc));
}
cifs_stats_inc(&tcon->num_fclose);
- cifs_small_buf_release(pSMB);
/* Since session is dead, search handle closed on server already */
if (rc == -EAGAIN)
__u16 fid, __u32 pid_of_opener, int SetAllocation)
{
struct smb_com_transaction2_sfi_req *pSMB = NULL;
- struct smb_com_transaction2_sfi_rsp *pSMBr = NULL;
char *data_offset;
struct file_end_of_file_info *parm_data;
int rc = 0;
- int bytes_returned = 0;
__u16 params, param_offset, offset, byte_count, count;
cFYI(1, ("SetFileSize (via SetFileInfo) %lld",
if (rc)
return rc;
- pSMBr = (struct smb_com_transaction2_sfi_rsp *)pSMB;
-
pSMB->hdr.Pid = cpu_to_le16((__u16)pid_of_opener);
pSMB->hdr.PidHigh = cpu_to_le16((__u16)(pid_of_opener >> 16));
pSMB->Reserved4 = 0;
pSMB->hdr.smb_buf_length += byte_count;
pSMB->ByteCount = cpu_to_le16(byte_count);
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cFYI(1,
("Send error in SetFileInfo (SetFileSize) = %d",
rc));
}
- if (pSMB)
- cifs_small_buf_release(pSMB);
-
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
const FILE_BASIC_INFO *data, __u16 fid)
{
struct smb_com_transaction2_sfi_req *pSMB = NULL;
- struct smb_com_transaction2_sfi_rsp *pSMBr = NULL;
char *data_offset;
int rc = 0;
- int bytes_returned = 0;
__u16 params, param_offset, offset, byte_count, count;
cFYI(1, ("Set Times (via SetFileInfo)"));
if (rc)
return rc;
- pSMBr = (struct smb_com_transaction2_sfi_rsp *)pSMB;
-
/* At this point there is no need to override the current pid
with the pid of the opener, but that could change if we someday
use an existing handle (rather than opening one on the fly) */
pSMB->hdr.smb_buf_length += byte_count;
pSMB->ByteCount = cpu_to_le16(byte_count);
memcpy(data_offset, data, sizeof(FILE_BASIC_INFO));
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cFYI(1, ("Send error in Set Time (SetFileInfo) = %d", rc));
}
- cifs_small_buf_release(pSMB);
-
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
pSMB->ByteCount = 0;
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, -1);
+ (struct smb_hdr *)pSMBr, &bytes_returned,
+ CIFS_ASYNC_OP);
if (rc) {
cFYI(1, ("Error in Notify = %d", rc));
} else {
csocket = server->ssocket;
wake_up(&server->response_q);
continue;
- } else if (length < 4) {
- cFYI(1, ("less than four bytes received (%d bytes)",
- length));
+ } else if (length < pdu_length) {
+ cFYI(1, ("requested %d bytes but only got %d bytes",
+ pdu_length, length));
pdu_length -= length;
msleep(1);
goto incomplete_rcv;
}
write_unlock(&GlobalSMBSeslock);
+ kfree(server->hostname);
kfree(server);
if (length > 0)
mempool_resize(cifs_req_poolp, length + cifs_min_rcv,
return 0;
}
+/* extract the host portion of the UNC string */
+static char *
+extract_hostname(const char *unc)
+{
+ const char *src;
+ char *dst, *delim;
+ unsigned int len;
+
+ /* skip double chars at beginning of string */
+ /* BB: check validity of these bytes? */
+ src = unc + 2;
+
+ /* delimiter between hostname and sharename is always '\\' now */
+ delim = strchr(src, '\\');
+ if (!delim)
+ return ERR_PTR(-EINVAL);
+
+ len = delim - src;
+ dst = kmalloc((len + 1), GFP_KERNEL);
+ if (dst == NULL)
+ return ERR_PTR(-ENOMEM);
+
+ memcpy(dst, src, len);
+ dst[len] = '\0';
+
+ return dst;
+}
+
static int
cifs_parse_mount_options(char *options, const char *devname,
struct smb_vol *vol)
memset(&volume_info, 0, sizeof(struct smb_vol));
if (cifs_parse_mount_options(mount_data, devname, &volume_info)) {
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (volume_info.nullauth) {
cifserror("No username specified");
/* In userspace mount helper we can get user name from alternate
locations such as env variables and files on disk */
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (volume_info.UNCip && volume_info.UNC) {
if (rc <= 0) {
/* we failed translating address */
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
cFYI(1, ("UNC: %s ip: %s", volume_info.UNC, volume_info.UNCip));
/* BB using ip addr as server name to connect to the
DFS root below */
cERROR(1, ("Connecting to DFS root not implemented yet"));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
} else /* which servers DFS root would we conect to */ {
cERROR(1,
("CIFS mount error: No UNC path (e.g. -o "
"unc=//192.168.1.100/public) specified"));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
/* this is needed for ASCII cp to Unicode converts */
if (cifs_sb->local_nls == NULL) {
cERROR(1, ("CIFS mount error: iocharset %s not found",
volume_info.iocharset));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -ELIBACC;
+ rc = -ELIBACC;
+ goto out;
}
}
&sin_server6.sin6_addr,
volume_info.username, &srvTcp);
} else {
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (srvTcp) {
"Aborting operation"));
if (csocket != NULL)
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ goto out;
}
srvTcp = kzalloc(sizeof(struct TCP_Server_Info), GFP_KERNEL);
if (!srvTcp) {
rc = -ENOMEM;
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ goto out;
} else {
memcpy(&srvTcp->addr.sockAddr, &sin_server,
sizeof(struct sockaddr_in));
/* BB Add code for ipv6 case too */
srvTcp->ssocket = csocket;
srvTcp->protocolType = IPV4;
+ srvTcp->hostname = extract_hostname(volume_info.UNC);
+ if (IS_ERR(srvTcp->hostname)) {
+ rc = PTR_ERR(srvTcp->hostname);
+ sock_release(csocket);
+ goto out;
+ }
init_waitqueue_head(&srvTcp->response_q);
init_waitqueue_head(&srvTcp->request_q);
INIT_LIST_HEAD(&srvTcp->pending_mid_q);
srvTcp->tcpStatus = CifsNew;
init_MUTEX(&srvTcp->tcpSem);
srvTcp->tsk = kthread_run((void *)(void *)cifs_demultiplex_thread, srvTcp, "cifsd");
- if ( IS_ERR(srvTcp->tsk) ) {
+ if (IS_ERR(srvTcp->tsk)) {
rc = PTR_ERR(srvTcp->tsk);
cERROR(1, ("error %d create cifsd thread", rc));
srvTcp->tsk = NULL;
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ kfree(srvTcp->hostname);
+ goto out;
}
wait_for_completion(&cifsd_complete);
rc = 0;
if (existingCifsSes) {
pSesInfo = existingCifsSes;
cFYI(1, ("Existing smb sess found"));
- kfree(volume_info.password);
- /* volume_info.UNC freed at end of function */
} else if (!rc) {
cFYI(1, ("Existing smb sess not found"));
pSesInfo = sesInfoAlloc();
if (!rc) {
/* volume_info.password freed at unmount */
- if (volume_info.password)
+ if (volume_info.password) {
pSesInfo->password = volume_info.password;
+ /* set to NULL to prevent freeing on exit */
+ volume_info.password = NULL;
+ }
if (volume_info.username)
strncpy(pSesInfo->userName,
volume_info.username,
up(&pSesInfo->sesSem);
if (!rc)
atomic_inc(&srvTcp->socketUseCount);
- } else
- kfree(volume_info.password);
+ }
}
/* search for existing tcon to this server share */
"", cifs_sb->local_nls,
cifs_sb->mnt_cifs_flags &
CIFS_MOUNT_MAP_SPECIAL_CHR);
- kfree(volume_info.UNC);
- FreeXid(xid);
- return -ENODEV;
+ rc = -ENODEV;
+ goto out;
} else {
/* BB Do we need to wrap sesSem around
* this TCon call and Unix SetFS as
(in which case it is not needed anymore) but when new sesion is created
the password ptr is put in the new session structure (in which case the
password will be freed at unmount time) */
+out:
+ /* zero out password before freeing */
+ if (volume_info.password != NULL) {
+ memset(volume_info.password, 0, strlen(volume_info.password));
+ kfree(volume_info.password);
+ }
kfree(volume_info.UNC);
kfree(volume_info.prepath);
FreeXid(xid);
pSMB->req_no_secext.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (rc) {
/* rc = map_smb_to_linux_error(smb_buffer_response); now done in SendReceive */
} else if ((smb_buffer_response->WordCount == 3)
pSMB->req.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (smb_buffer_response->Status.CifsError ==
cpu_to_le32(NT_STATUS_MORE_PROCESSING_REQUIRED))
pSMB->req.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (rc) {
/* rc = map_smb_to_linux_error(smb_buffer_response) done in SendReceive now */
} else if ((smb_buffer_response->WordCount == 3) ||
pSMB->hdr.smb_buf_length += count;
pSMB->ByteCount = cpu_to_le16(count);
- rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response, &length, 0);
+ rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response, &length,
+ CIFS_STD_OP);
/* if (rc) rc = map_smb_to_linux_error(smb_buffer_response); */
/* above now done in SendReceive */
if (file->f_path.dentry->d_inode->i_mapping) {
/* BB no need to lock inode until after invalidate
since namei code should already have it locked? */
- filemap_write_and_wait(file->f_path.dentry->d_inode->i_mapping);
+ rc = filemap_write_and_wait(file->f_path.dentry->d_inode->i_mapping);
+ if (rc != 0)
+ CIFS_I(file->f_path.dentry->d_inode)->write_behind_rc = rc;
}
cFYI(1, ("invalidating remote inode since open detected it "
"changed"));
pCifsInode = CIFS_I(inode);
if (pCifsInode) {
if (can_flush) {
- filemap_write_and_wait(inode->i_mapping);
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc != 0)
+ CIFS_I(inode)->write_behind_rc = rc;
/* temporarily disable caching while we
go to server to get inode info */
pCifsInode->clientCanCacheAll = FALSE;
xid = GetXid();
if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = 2; /* writes past end of file can take a long time */
+ long_op = CIFS_VLONG_OP; /* writes past EOF take long time */
else
- long_op = 1;
+ long_op = CIFS_LONG_OP;
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
}
} else
*poffset += bytes_written;
- long_op = FALSE; /* subsequent writes fast -
+ long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
xid = GetXid();
if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = 2; /* writes past end of file can take a long time */
+ long_op = CIFS_VLONG_OP; /* writes past EOF can be slow */
else
- long_op = 1;
+ long_op = CIFS_LONG_OP;
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
}
} else
*poffset += bytes_written;
- long_op = FALSE; /* subsequent writes fast -
+ long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
read_unlock(&GlobalSMBSeslock);
return open_file;
}
-
+
read_unlock(&GlobalSMBSeslock);
/* Had to unlock since following call can block */
rc = cifs_reopen_file(open_file->pfile, FALSE);
- if (!rc) {
+ if (!rc) {
if (!open_file->closePend)
return open_file;
else { /* start over in case this was deleted */
/* can not use this handle, no write
pending on this one after all */
atomic_dec(&open_file->wrtPending);
-
+
if (open_file->closePend) /* list could have changed */
goto refind_writable;
/* else we simply continue to the next entry. Thus
open_file->netfid,
bytes_to_write, offset,
&bytes_written, iov, n_iov,
- 1);
+ CIFS_LONG_OP);
atomic_dec(&open_file->wrtPending);
if (rc || bytes_written < bytes_to_write) {
cERROR(1, ("Write2 ret %d, wrote %d",
rc, bytes_written));
/* BB what if continued retry is
requested via mount flags? */
- set_bit(AS_EIO, &mapping->flags);
+ if (rc == -ENOSPC)
+ set_bit(AS_ENOSPC, &mapping->flags);
+ else
+ set_bit(AS_EIO, &mapping->flags);
} else {
cifs_stats_bytes_written(cifs_sb->tcon,
bytes_written);
cFYI(1, ("Sync file - name: %s datasync: 0x%x",
dentry->d_name.name, datasync));
- rc = filemap_fdatawrite(inode->i_mapping);
- if (rc == 0)
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc == 0) {
+ rc = CIFS_I(inode)->write_behind_rc;
CIFS_I(inode)->write_behind_rc = 0;
+ }
FreeXid(xid);
return rc;
}
filemapfdatawrite appears easier for the time being */
rc = filemap_fdatawrite(inode->i_mapping);
- if (!rc) /* reset wb rc if we were able to write out dirty pages */
+ /* reset wb rc if we were able to write out dirty pages */
+ if (!rc) {
+ rc = CIFS_I(inode)->write_behind_rc;
CIFS_I(inode)->write_behind_rc = 0;
+ }
cFYI(1, ("Flush inode %p file %p rc %d", inode, file, rc));
int cifs_revalidate(struct dentry *direntry)
{
int xid;
- int rc = 0;
+ int rc = 0, wbrc = 0;
char *full_path;
struct cifs_sb_info *cifs_sb;
struct cifsInodeInfo *cifsInode;
if (direntry->d_inode->i_mapping) {
/* do we need to lock inode until after invalidate completes
below? */
- filemap_fdatawrite(direntry->d_inode->i_mapping);
+ wbrc = filemap_fdatawrite(direntry->d_inode->i_mapping);
+ if (wbrc)
+ CIFS_I(direntry->d_inode)->write_behind_rc = wbrc;
}
if (invalidate_inode) {
/* shrink_dcache not necessary now that cifs dentry ops
shrink_dcache_parent(direntry); */
if (S_ISREG(direntry->d_inode->i_mode)) {
if (direntry->d_inode->i_mapping)
- filemap_fdatawait(direntry->d_inode->i_mapping);
+ wbrc = filemap_fdatawait(direntry->d_inode->i_mapping);
+ if (wbrc)
+ CIFS_I(direntry->d_inode)->write_behind_rc = wbrc;
/* may eventually have to do this for open files too */
if (list_empty(&(cifsInode->openFileList))) {
/* changed on server - flush read ahead pages */
/* BB check if we need to refresh inode from server now ? BB */
- /* need to flush data before changing file size on server */
- filemap_write_and_wait(direntry->d_inode->i_mapping);
-
if (attrs->ia_valid & ATTR_SIZE) {
+ /*
+ Flush data before changing file size on server. If the
+ flush returns error, store it to report later and continue.
+ BB: This should be smarter. Why bother flushing pages that
+ will be truncated anyway? Also, should we error out here if
+ the flush returns error?
+ */
+ rc = filemap_write_and_wait(direntry->d_inode->i_mapping);
+ if (rc != 0) {
+ CIFS_I(direntry->d_inode)->write_behind_rc = rc;
+ rc = 0;
+ }
+
/* To avoid spurious oplock breaks from server, in the case of
inodes that we already have open, avoid doing path based
setting of file size if we can do it by handle.
#include "ntlmssp.h"
#include "nterr.h"
#include <linux/utsname.h>
+#include "cifs_spnego.h"
extern void SMBNTencrypt(unsigned char *passwd, unsigned char *c8,
unsigned char *p24);
SESSION_SETUP_ANDX *pSMB;
__u32 capabilities;
int count;
- int resp_buf_type = 0;
- struct kvec iov[2];
+ int resp_buf_type;
+ struct kvec iov[3];
enum securityEnum type;
__u16 action;
int bytes_remaining;
+ struct key *spnego_key = NULL;
if (ses == NULL)
return -EINVAL;
capabilities = cifs_ssetup_hdr(ses, pSMB);
- /* we will send the SMB in two pieces,
- a fixed length beginning part, and a
- second part which will include the strings
- and rest of bcc area, in order to avoid having
- to do a large buffer 17K allocation */
+ /* we will send the SMB in three pieces:
+ a fixed length beginning part, an optional
+ SPNEGO blob (which can be zero length), and a
+ last part which will include the strings
+ and rest of bcc area. This allows us to avoid
+ a large buffer 17K allocation */
iov[0].iov_base = (char *)pSMB;
iov[0].iov_len = smb_buf->smb_buf_length + 4;
+ /* setting this here allows the code at the end of the function
+ to free the request buffer if there's an error */
+ resp_buf_type = CIFS_SMALL_BUFFER;
+
/* 2000 big enough to fit max user, domain, NOS name etc. */
str_area = kmalloc(2000, GFP_KERNEL);
if (str_area == NULL) {
- cifs_small_buf_release(smb_buf);
- return -ENOMEM;
+ rc = -ENOMEM;
+ goto ssetup_exit;
}
bcc_ptr = str_area;
ses->flags &= ~CIFS_SES_LANMAN;
+ iov[1].iov_base = NULL;
+ iov[1].iov_len = 0;
+
if (type == LANMAN) {
#ifdef CONFIG_CIFS_WEAK_PW_HASH
char lnm_session_key[CIFS_SESS_KEY_SIZE];
struct ntlmv2_resp */
if (v2_sess_key == NULL) {
- cifs_small_buf_release(smb_buf);
- return -ENOMEM;
+ rc = -ENOMEM;
+ goto ssetup_exit;
}
pSMB->req_no_secext.Capabilities = cpu_to_le32(capabilities);
unicode_ssetup_strings(&bcc_ptr, ses, nls_cp);
} else
ascii_ssetup_strings(&bcc_ptr, ses, nls_cp);
- } else /* NTLMSSP or SPNEGO */ {
+ } else if (type == Kerberos) {
+#ifdef CONFIG_CIFS_UPCALL
+ struct cifs_spnego_msg *msg;
+ spnego_key = cifs_get_spnego_key(ses);
+ if (IS_ERR(spnego_key)) {
+ rc = PTR_ERR(spnego_key);
+ spnego_key = NULL;
+ goto ssetup_exit;
+ }
+
+ msg = spnego_key->payload.data;
+ /* bail out if key is too long */
+ if (msg->sesskey_len >
+ sizeof(ses->server->mac_signing_key.data.krb5)) {
+ cERROR(1, ("Kerberos signing key too long (%u bytes)",
+ msg->sesskey_len));
+ rc = -EOVERFLOW;
+ goto ssetup_exit;
+ }
+ ses->server->mac_signing_key.len = msg->sesskey_len;
+ memcpy(ses->server->mac_signing_key.data.krb5, msg->data,
+ msg->sesskey_len);
pSMB->req.hdr.Flags2 |= SMBFLG2_EXT_SEC;
capabilities |= CAP_EXTENDED_SECURITY;
pSMB->req.Capabilities = cpu_to_le32(capabilities);
- /* BB set password lengths */
+ iov[1].iov_base = msg->data + msg->sesskey_len;
+ iov[1].iov_len = msg->secblob_len;
+ pSMB->req.SecurityBlobLength = cpu_to_le16(iov[1].iov_len);
+
+ if (ses->capabilities & CAP_UNICODE) {
+ /* unicode strings must be word aligned */
+ if (iov[0].iov_len % 2) {
+ *bcc_ptr = 0;
+ bcc_ptr++;
+ }
+ unicode_oslm_strings(&bcc_ptr, nls_cp);
+ unicode_domain_string(&bcc_ptr, ses, nls_cp);
+ } else
+ /* BB: is this right? */
+ ascii_ssetup_strings(&bcc_ptr, ses, nls_cp);
+#else /* ! CONFIG_CIFS_UPCALL */
+ cERROR(1, ("Kerberos negotiated but upcall support disabled!"));
+ rc = -ENOSYS;
+ goto ssetup_exit;
+#endif /* CONFIG_CIFS_UPCALL */
+ } else {
+ cERROR(1, ("secType %d not supported!", type));
+ rc = -ENOSYS;
+ goto ssetup_exit;
}
- count = (long) bcc_ptr - (long) str_area;
+ iov[2].iov_base = str_area;
+ iov[2].iov_len = (long) bcc_ptr - (long) str_area;
+
+ count = iov[1].iov_len + iov[2].iov_len;
smb_buf->smb_buf_length += count;
BCC_LE(smb_buf) = cpu_to_le16(count);
- iov[1].iov_base = str_area;
- iov[1].iov_len = count;
- rc = SendReceive2(xid, ses, iov, 2 /* num_iovecs */, &resp_buf_type,
- 0 /* not long op */, 1 /* log NT STATUS if any */ );
+ rc = SendReceive2(xid, ses, iov, 3 /* num_iovecs */, &resp_buf_type,
+ CIFS_STD_OP /* not long */ | CIFS_LOG_ERROR);
/* SMB request buf freed in SendReceive2 */
cFYI(1, ("ssetup rc from sendrecv2 is %d", rc));
ses, nls_cp);
ssetup_exit:
+ if (spnego_key)
+ key_put(spnego_key);
kfree(str_area);
if (resp_buf_type == CIFS_SMALL_BUFFER) {
cFYI(1, ("ssetup freeing small buf %p", iov[0].iov_base));
static int wait_for_free_request(struct cifsSesInfo *ses, const int long_op)
{
- if (long_op == -1) {
+ if (long_op == CIFS_ASYNC_OP) {
/* oplock breaks must not be held up */
atomic_inc(&ses->server->inFlight);
} else {
as they are allowed to block on server */
/* update # of requests on the wire to server */
- if (long_op < 3)
+ if (long_op != CIFS_BLOCKING_OP)
atomic_inc(&ses->server->inFlight);
spin_unlock(&GlobalMid_Lock);
break;
}
}
+
+/*
+ *
+ * Send an SMB Request. No response info (other than return code)
+ * needs to be parsed.
+ *
+ * flags indicate the type of request buffer and how long to wait
+ * and whether to log NT STATUS code (error) before mapping it to POSIX error
+ *
+ */
+int
+SendReceiveNoRsp(const unsigned int xid, struct cifsSesInfo *ses,
+ struct smb_hdr *in_buf, int flags)
+{
+ int rc;
+ struct kvec iov[1];
+ int resp_buf_type;
+
+ iov[0].iov_base = (char *)in_buf;
+ iov[0].iov_len = in_buf->smb_buf_length + 4;
+ flags |= CIFS_NO_RESP;
+ rc = SendReceive2(xid, ses, iov, 1, &resp_buf_type, flags);
+#ifdef CONFIG_CIFS_DEBUG2
+ cFYI(1, ("SendRcvNoR flags %d rc %d", flags, rc));
+#endif
+ return rc;
+}
+
int
SendReceive2(const unsigned int xid, struct cifsSesInfo *ses,
struct kvec *iov, int n_vec, int *pRespBufType /* ret */,
- const int long_op, const int logError)
+ const int flags)
{
int rc = 0;
+ int long_op;
unsigned int receive_len;
unsigned long timeout;
struct mid_q_entry *midQ;
struct smb_hdr *in_buf = iov[0].iov_base;
+ long_op = flags & CIFS_TIMEOUT_MASK;
+
*pRespBufType = CIFS_NO_BUFFER; /* no response buf yet */
if ((ses == NULL) || (ses->server == NULL)) {
if (rc < 0)
goto out;
- if (long_op == -1)
- goto out;
- else if (long_op == 2) /* writes past end of file can take loong time */
+ if (long_op == CIFS_STD_OP)
+ timeout = 15 * HZ;
+ else if (long_op == CIFS_VLONG_OP) /* e.g. slow writes past EOF */
timeout = 180 * HZ;
- else if (long_op == 1)
+ else if (long_op == CIFS_LONG_OP)
timeout = 45 * HZ; /* should be greater than
servers oplock break timeout (about 43 seconds) */
- else
- timeout = 15 * HZ;
+ else if (long_op == CIFS_ASYNC_OP)
+ goto out;
+ else if (long_op == CIFS_BLOCKING_OP)
+ timeout = 0x7FFFFFFF; /* large, but not so large as to wrap */
+ else {
+ cERROR(1, ("unknown timeout flag %d", long_op));
+ rc = -EIO;
+ goto out;
+ }
/* wait for 15 seconds or until woken up due to response arriving or
due to last connection to this server being unmounted */
}
/* BB special case reconnect tid and uid here? */
- rc = map_smb_to_linux_error(midQ->resp_buf, logError);
+ rc = map_smb_to_linux_error(midQ->resp_buf,
+ flags & CIFS_LOG_ERROR);
/* convert ByteCount if necessary */
if (receive_len >= sizeof(struct smb_hdr) - 4
(2 * midQ->resp_buf->WordCount) + 2 /* bcc */ )
BCC(midQ->resp_buf) =
le16_to_cpu(BCC_LE(midQ->resp_buf));
- midQ->resp_buf = NULL; /* mark it so will not be freed
- by DeleteMidQEntry */
+ if ((flags & CIFS_NO_RESP) == 0)
+ midQ->resp_buf = NULL; /* mark it so buf will
+ not be freed by
+ DeleteMidQEntry */
} else {
rc = -EIO;
cFYI(1, ("Bad MID state?"));
if (rc < 0)
goto out;
- if (long_op == -1)
+ if (long_op == CIFS_STD_OP)
+ timeout = 15 * HZ;
+ /* wait for 15 seconds or until woken up due to response arriving or
+ due to last connection to this server being unmounted */
+ else if (long_op == CIFS_ASYNC_OP)
goto out;
- else if (long_op == 2) /* writes past end of file can take loong time */
+ else if (long_op == CIFS_VLONG_OP) /* writes past EOF can be slow */
timeout = 180 * HZ;
- else if (long_op == 1)
+ else if (long_op == CIFS_LONG_OP)
timeout = 45 * HZ; /* should be greater than
servers oplock break timeout (about 43 seconds) */
- else
- timeout = 15 * HZ;
- /* wait for 15 seconds or until woken up due to response arriving or
- due to last connection to this server being unmounted */
+ else if (long_op == CIFS_BLOCKING_OP)
+ timeout = 0x7FFFFFFF; /* large but no so large as to wrap */
+ else {
+ cERROR(1, ("unknown timeout flag %d", long_op));
+ rc = -EIO;
+ goto out;
+ }
+
if (signal_pending(current)) {
/* if signal pending do not hold up user for full smb timeout
but we still give response a chance to complete */
pSMB->hdr.Mid = GetNextMid(ses->server);
return SendReceive(xid, ses, in_buf, out_buf,
- &bytes_returned, 0);
+ &bytes_returned, CIFS_STD_OP);
}
int
to the same server. We may make this configurable later or
use ses->maxReq */
- rc = wait_for_free_request(ses, 3);
+ rc = wait_for_free_request(ses, CIFS_BLOCKING_OP);
if (rc)
return rc;
#include "nfs4_fs.h"
#include "delegation.h"
#include "iostat.h"
+#include "internal.h"
/* #define NFS_DEBUG_VERBOSE 1 */
* handled automatically by nfs_direct_read_result(). Otherwise, if
* no requests have been sent, just return an error.
*/
-static ssize_t nfs_direct_read_schedule(struct nfs_direct_req *dreq, unsigned long user_addr, size_t count, loff_t pos)
+static ssize_t nfs_direct_read_schedule_segment(struct nfs_direct_req *dreq,
+ const struct iovec *iov,
+ loff_t pos)
{
struct nfs_open_context *ctx = dreq->ctx;
struct inode *inode = ctx->path.dentry->d_inode;
+ unsigned long user_addr = (unsigned long)iov->iov_base;
+ size_t count = iov->iov_len;
size_t rsize = NFS_SERVER(inode)->rsize;
unsigned int pgbase;
int result;
ssize_t started = 0;
- get_dreq(dreq);
-
do {
struct nfs_read_data *data;
size_t bytes;
count -= bytes;
} while (count != 0);
+ if (started)
+ return started;
+ return result < 0 ? (ssize_t) result : -EFAULT;
+}
+
+static ssize_t nfs_direct_read_schedule_iovec(struct nfs_direct_req *dreq,
+ const struct iovec *iov,
+ unsigned long nr_segs,
+ loff_t pos)
+{
+ ssize_t result = -EINVAL;
+ size_t requested_bytes = 0;
+ unsigned long seg;
+
+ get_dreq(dreq);
+
+ for (seg = 0; seg < nr_segs; seg++) {
+ const struct iovec *vec = &iov[seg];
+ result = nfs_direct_read_schedule_segment(dreq, vec, pos);
+ if (result < 0)
+ break;
+ requested_bytes += result;
+ if ((size_t)result < vec->iov_len)
+ break;
+ pos += vec->iov_len;
+ }
+
if (put_dreq(dreq))
nfs_direct_complete(dreq);
- if (started)
+ if (requested_bytes != 0)
return 0;
- return result < 0 ? (ssize_t) result : -EFAULT;
+
+ if (result < 0)
+ return result;
+ return -EIO;
}
-static ssize_t nfs_direct_read(struct kiocb *iocb, unsigned long user_addr, size_t count, loff_t pos)
+static ssize_t nfs_direct_read(struct kiocb *iocb, const struct iovec *iov,
+ unsigned long nr_segs, loff_t pos)
{
ssize_t result = 0;
sigset_t oldset;
if (!is_sync_kiocb(iocb))
dreq->iocb = iocb;
- nfs_add_stats(inode, NFSIOS_DIRECTREADBYTES, count);
rpc_clnt_sigmask(clnt, &oldset);
- result = nfs_direct_read_schedule(dreq, user_addr, count, pos);
+ result = nfs_direct_read_schedule_iovec(dreq, iov, nr_segs, pos);
if (!result)
result = nfs_direct_wait(dreq);
rpc_clnt_sigunmask(clnt, &oldset);
* handled automatically by nfs_direct_write_result(). Otherwise, if
* no requests have been sent, just return an error.
*/
-static ssize_t nfs_direct_write_schedule(struct nfs_direct_req *dreq, unsigned long user_addr, size_t count, loff_t pos, int sync)
+static ssize_t nfs_direct_write_schedule_segment(struct nfs_direct_req *dreq,
+ const struct iovec *iov,
+ loff_t pos, int sync)
{
struct nfs_open_context *ctx = dreq->ctx;
struct inode *inode = ctx->path.dentry->d_inode;
+ unsigned long user_addr = (unsigned long)iov->iov_base;
+ size_t count = iov->iov_len;
size_t wsize = NFS_SERVER(inode)->wsize;
unsigned int pgbase;
int result;
ssize_t started = 0;
- get_dreq(dreq);
-
do {
struct nfs_write_data *data;
size_t bytes;
count -= bytes;
} while (count != 0);
+ if (started)
+ return started;
+ return result < 0 ? (ssize_t) result : -EFAULT;
+}
+
+static ssize_t nfs_direct_write_schedule_iovec(struct nfs_direct_req *dreq,
+ const struct iovec *iov,
+ unsigned long nr_segs,
+ loff_t pos, int sync)
+{
+ ssize_t result = 0;
+ size_t requested_bytes = 0;
+ unsigned long seg;
+
+ get_dreq(dreq);
+
+ for (seg = 0; seg < nr_segs; seg++) {
+ const struct iovec *vec = &iov[seg];
+ result = nfs_direct_write_schedule_segment(dreq, vec,
+ pos, sync);
+ if (result < 0)
+ break;
+ requested_bytes += result;
+ if ((size_t)result < vec->iov_len)
+ break;
+ pos += vec->iov_len;
+ }
+
if (put_dreq(dreq))
- nfs_direct_write_complete(dreq, inode);
+ nfs_direct_write_complete(dreq, dreq->inode);
- if (started)
+ if (requested_bytes != 0)
return 0;
- return result < 0 ? (ssize_t) result : -EFAULT;
+
+ if (result < 0)
+ return result;
+ return -EIO;
}
-static ssize_t nfs_direct_write(struct kiocb *iocb, unsigned long user_addr, size_t count, loff_t pos)
+static ssize_t nfs_direct_write(struct kiocb *iocb, const struct iovec *iov,
+ unsigned long nr_segs, loff_t pos,
+ size_t count)
{
ssize_t result = 0;
sigset_t oldset;
if (!is_sync_kiocb(iocb))
dreq->iocb = iocb;
- nfs_add_stats(inode, NFSIOS_DIRECTWRITTENBYTES, count);
-
rpc_clnt_sigmask(clnt, &oldset);
- result = nfs_direct_write_schedule(dreq, user_addr, count, pos, sync);
+ result = nfs_direct_write_schedule_iovec(dreq, iov, nr_segs, pos, sync);
if (!result)
result = nfs_direct_wait(dreq);
rpc_clnt_sigunmask(clnt, &oldset);
ssize_t retval = -EINVAL;
struct file *file = iocb->ki_filp;
struct address_space *mapping = file->f_mapping;
- /* XXX: temporary */
- const char __user *buf = iov[0].iov_base;
- size_t count = iov[0].iov_len;
+ size_t count;
+
+ count = iov_length(iov, nr_segs);
+ nfs_add_stats(mapping->host, NFSIOS_DIRECTREADBYTES, count);
- dprintk("nfs: direct read(%s/%s, %lu@%Ld)\n",
+ dprintk("nfs: direct read(%s/%s, %zd@%Ld)\n",
file->f_path.dentry->d_parent->d_name.name,
file->f_path.dentry->d_name.name,
- (unsigned long) count, (long long) pos);
-
- if (nr_segs != 1)
- goto out;
+ count, (long long) pos);
- retval = -EFAULT;
- if (!access_ok(VERIFY_WRITE, buf, count))
- goto out;
retval = 0;
if (!count)
goto out;
if (retval)
goto out;
- retval = nfs_direct_read(iocb, (unsigned long) buf, count, pos);
+ retval = nfs_direct_read(iocb, iov, nr_segs, pos);
if (retval > 0)
iocb->ki_pos = pos + retval;
ssize_t retval = -EINVAL;
struct file *file = iocb->ki_filp;
struct address_space *mapping = file->f_mapping;
- /* XXX: temporary */
- const char __user *buf = iov[0].iov_base;
- size_t count = iov[0].iov_len;
+ size_t count;
+
+ count = iov_length(iov, nr_segs);
+ nfs_add_stats(mapping->host, NFSIOS_DIRECTWRITTENBYTES, count);
- dprintk("nfs: direct write(%s/%s, %lu@%Ld)\n",
+ dfprintk(VFS, "nfs: direct write(%s/%s, %zd@%Ld)\n",
file->f_path.dentry->d_parent->d_name.name,
file->f_path.dentry->d_name.name,
- (unsigned long) count, (long long) pos);
-
- if (nr_segs != 1)
- goto out;
+ count, (long long) pos);
retval = generic_write_checks(file, &pos, &count, 0);
if (retval)
goto out;
+ if (!count)
+ goto out; /* return 0 */
retval = -EINVAL;
if ((ssize_t) count < 0)
if (!count)
goto out;
- retval = -EFAULT;
- if (!access_ok(VERIFY_READ, buf, count))
- goto out;
-
retval = nfs_sync_mapping(mapping);
if (retval)
goto out;
- retval = nfs_direct_write(iocb, (unsigned long) buf, count, pos);
+ retval = nfs_direct_write(iocb, iov, nr_segs, pos, count);
if (retval > 0)
iocb->ki_pos = pos + retval;
#define NFSDBG_FACILITY NFSDBG_CLIENT
+/*
+ * Set the superblock root dentry.
+ * Note that this function frees the inode in case of error.
+ */
+static int nfs_superblock_set_dummy_root(struct super_block *sb, struct inode *inode)
+{
+ /* The mntroot acts as the dummy root dentry for this superblock */
+ if (sb->s_root == NULL) {
+ sb->s_root = d_alloc_root(inode);
+ if (sb->s_root == NULL) {
+ iput(inode);
+ return -ENOMEM;
+ }
+ /* Circumvent igrab(): we know the inode is not being freed */
+ atomic_inc(&inode->i_count);
+ }
+ return 0;
+}
+
/*
* get an NFS2/NFS3 root dentry from the root filehandle
*/
struct inode *inode;
int error;
- /* create a dummy root dentry with dummy inode for this superblock */
- if (!sb->s_root) {
- struct nfs_fh dummyfh;
- struct dentry *root;
- struct inode *iroot;
-
- memset(&dummyfh, 0, sizeof(dummyfh));
- memset(&fattr, 0, sizeof(fattr));
- nfs_fattr_init(&fattr);
- fattr.valid = NFS_ATTR_FATTR;
- fattr.type = NFDIR;
- fattr.mode = S_IFDIR | S_IRUSR | S_IWUSR;
- fattr.nlink = 2;
-
- iroot = nfs_fhget(sb, &dummyfh, &fattr);
- if (IS_ERR(iroot))
- return ERR_PTR(PTR_ERR(iroot));
-
- root = d_alloc_root(iroot);
- if (!root) {
- iput(iroot);
- return ERR_PTR(-ENOMEM);
- }
-
- sb->s_root = root;
- }
-
/* get the actual root for this mount */
fsinfo.fattr = &fattr;
return ERR_PTR(PTR_ERR(inode));
}
+ error = nfs_superblock_set_dummy_root(sb, inode);
+ if (error != 0)
+ return ERR_PTR(error);
+
/* root dentries normally start off anonymous and get spliced in later
* if the dentry tree reaches them; however if the dentry already
* exists, we'll pick it up at this point and use it as the root
dprintk("--> nfs4_get_root()\n");
- /* create a dummy root dentry with dummy inode for this superblock */
- if (!sb->s_root) {
- struct nfs_fh dummyfh;
- struct dentry *root;
- struct inode *iroot;
-
- memset(&dummyfh, 0, sizeof(dummyfh));
- memset(&fattr, 0, sizeof(fattr));
- nfs_fattr_init(&fattr);
- fattr.valid = NFS_ATTR_FATTR;
- fattr.type = NFDIR;
- fattr.mode = S_IFDIR | S_IRUSR | S_IWUSR;
- fattr.nlink = 2;
-
- iroot = nfs_fhget(sb, &dummyfh, &fattr);
- if (IS_ERR(iroot))
- return ERR_PTR(PTR_ERR(iroot));
-
- root = d_alloc_root(iroot);
- if (!root) {
- iput(iroot);
- return ERR_PTR(-ENOMEM);
- }
-
- sb->s_root = root;
- }
-
/* get the info about the server and filesystem */
error = nfs4_server_capabilities(server, mntfh);
if (error < 0) {
return ERR_PTR(PTR_ERR(inode));
}
+ error = nfs_superblock_set_dummy_root(sb, inode);
+ if (error != 0)
+ return ERR_PTR(error);
+
/* root dentries normally start off anonymous and get spliced in later
* if the dentry tree reaches them; however if the dentry already
* exists, we'll pick it up at this point and use it as the root
{
struct nfs_mount_data *data = (struct nfs_mount_data *)options;
+ memset(args, 0, sizeof(*args));
+
if (data == NULL)
goto out_no_data;
- memset(args, 0, sizeof(*args));
args->flags = (NFS_MOUNT_VER3 | NFS_MOUNT_TCP);
args->rsize = NFS_MAX_FILE_IO_SIZE;
args->wsize = NFS_MAX_FILE_IO_SIZE;
error = PTR_ERR(mntroot);
goto error_splat_super;
}
+ if (mntroot->d_inode->i_op != &nfs_dir_inode_operations) {
+ dput(mntroot);
+ error = -ESTALE;
+ goto error_splat_super;
+ }
s->s_flags |= MS_ACTIVE;
mnt->mnt_sb = s;
struct nfs4_mount_data *data = (struct nfs4_mount_data *)options;
char *c;
+ memset(args, 0, sizeof(*args));
+
if (data == NULL)
goto out_no_data;
- memset(args, 0, sizeof(*args));
args->rsize = NFS_MAX_FILE_IO_SIZE;
args->wsize = NFS_MAX_FILE_IO_SIZE;
args->timeo = 600;
return ret;
}
-int nfs_wb_page_priority(struct inode *inode, struct page *page, int how)
+static int nfs_wb_page_priority(struct inode *inode, struct page *page,
+ int how)
{
loff_t range_start = page_offset(page);
loff_t range_end = range_start + (loff_t)(PAGE_CACHE_SIZE - 1);
{
struct ocfs2_dinode *di = (struct ocfs2_dinode *)di_bh->b_data;
- if (new_size < le16_to_cpu(di->id2.i_data.id_count))
+ if (new_size <= le16_to_cpu(di->id2.i_data.id_count))
return 1;
return 0;
}
#define mlog_errno(st) do { \
int _st = (st); \
if (_st != -ERESTARTSYS && _st != -EINTR && \
- _st != AOP_TRUNCATED_PAGE) \
+ _st != AOP_TRUNCATED_PAGE && _st != -ENOSPC) \
mlog(ML_ERROR, "status = %lld\n", (long long)_st); \
} while (0)
{
struct ocfs2_dentry_lock *dl = dentry->d_fsdata;
- mlog_bug_on_msg(!dl && !(dentry->d_flags & DCACHE_DISCONNECTED),
- "dentry: %.*s\n", dentry->d_name.len,
- dentry->d_name.name);
+ if (!dl) {
+ /*
+ * No dentry lock is ok if we're disconnected or
+ * unhashed.
+ */
+ if (!(dentry->d_flags & DCACHE_DISCONNECTED) &&
+ !d_unhashed(dentry)) {
+ unsigned long long ino = 0ULL;
+ if (inode)
+ ino = (unsigned long long)OCFS2_I(inode)->ip_blkno;
+ mlog(ML_ERROR, "Dentry is missing cluster lock. "
+ "inode: %llu, d_flags: 0x%x, d_name: %.*s\n",
+ ino, dentry->d_flags, dentry->d_name.len,
+ dentry->d_name.name);
+ }
- if (!dl)
goto out;
+ }
mlog_bug_on_msg(dl->dl_count == 0, "dentry: %.*s, count: %u\n",
dentry->d_name.len, dentry->d_name.name,
* but they might own this lockres. wait on them. */
bit = find_next_bit(dlm->recovery_map, O2NM_MAX_NODES, 0);
if (bit < O2NM_MAX_NODES) {
- mlog(ML_NOTICE, "%s:%.*s: at least one node (%d) to"
+ mlog(ML_NOTICE, "%s:%.*s: at least one node (%d) to "
"recover before lock mastery can begin\n",
dlm->name, namelen, (char *)lockid, bit);
wait_on_recovery = 1;
spin_lock(&dlm->spinlock);
bit = find_next_bit(dlm->recovery_map, O2NM_MAX_NODES, 0);
if (bit < O2NM_MAX_NODES) {
- mlog(ML_NOTICE, "%s:%.*s: at least one node (%d) to"
+ mlog(ML_NOTICE, "%s:%.*s: at least one node (%d) to "
"recover before lock mastery can begin\n",
dlm->name, namelen, (char *)lockid, bit);
wait_on_recovery = 1;
if (OCFS2_I(inode)->ip_dyn_features & OCFS2_INLINE_DATA_FL) {
status = ocfs2_truncate_inline(inode, di_bh, new_i_size,
- i_size_read(inode), 0);
+ i_size_read(inode), 1);
if (status)
mlog_errno(status);
u32 trunc_start, trunc_len, cpos, phys_cpos, alloc_size;
struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);
struct ocfs2_cached_dealloc_ctxt dealloc;
+ struct address_space *mapping = inode->i_mapping;
ocfs2_init_dealloc_ctxt(&dealloc);
if (OCFS2_I(inode)->ip_dyn_features & OCFS2_INLINE_DATA_FL) {
ret = ocfs2_truncate_inline(inode, di_bh, byte_start,
- byte_start + byte_len, 1);
- if (ret)
+ byte_start + byte_len, 0);
+ if (ret) {
mlog_errno(ret);
- return ret;
+ goto out;
+ }
+ /*
+ * There's no need to get fancy with the page cache
+ * truncate of an inline-data inode. We're talking
+ * about less than a page here, which will be cached
+ * in the dinode buffer anyway.
+ */
+ unmap_mapping_range(mapping, 0, 0, 0);
+ truncate_inode_pages(mapping, 0);
+ goto out;
}
trunc_start = ocfs2_clusters_for_bytes(osb->sb, byte_start);
status = -EINVAL;
fe = (struct ocfs2_dinode *) bh->b_data;
if (!OCFS2_IS_VALID_DINODE(fe)) {
- mlog(ML_ERROR, "Invalid dinode #%llu: signature = %.*s\n",
- (unsigned long long)le64_to_cpu(fe->i_blkno), 7,
+ mlog(0, "Invalid dinode #%llu: signature = %.*s\n",
+ (unsigned long long)args->fi_blkno, 7,
fe->i_signature);
goto bail;
}
status = ocfs2_try_open_lock(inode, 1);
if (status == -EAGAIN) {
status = 0;
- mlog(0, "Skipping delete of %llu because it is in use on"
+ mlog(0, "Skipping delete of %llu because it is in use on "
"other nodes\n", (unsigned long long)oi->ip_blkno);
goto bail;
}
alloc = (struct ocfs2_dinode *) osb->local_alloc_bh->b_data;
+#ifdef OCFS2_DEBUG_FS
if (le32_to_cpu(alloc->id1.bitmap1.i_used) !=
ocfs2_local_alloc_count_bits(alloc)) {
ocfs2_error(osb->sb, "local alloc inode %llu says it has "
status = -EIO;
goto bail;
}
+#endif
free_bits = le32_to_cpu(alloc->id1.bitmap1.i_total) -
le32_to_cpu(alloc->id1.bitmap1.i_used);
void *bitmap;
struct ocfs2_local_alloc *la = OCFS2_LOCAL_ALLOC(alloc);
- mlog_entry("total = %u, COUNT = %u, used = %u\n",
+ mlog_entry("total = %u, used = %u\n",
le32_to_cpu(alloc->id1.bitmap1.i_total),
- ocfs2_local_alloc_count_bits(alloc),
le32_to_cpu(alloc->id1.bitmap1.i_used));
if (!alloc->id1.bitmap1.i_total) {
}
if (!ret) {
- if (!ocfs2_is_hard_readonly(osb))
- ocfs2_set_journal_params(osb);
-
/* Only save off the new mount options in case of a successful
* remount. */
osb->s_mount_opt = parsed_options.mount_opt;
osb->s_atime_quantum = parsed_options.atime_quantum;
osb->preferred_slot = parsed_options.slot;
+
+ if (!ocfs2_is_hard_readonly(osb))
+ ocfs2_set_journal_params(osb);
}
out:
return ret;
stime = nsec_to_clock_t(p->se.sum_exec_runtime) -
cputime_to_clock_t(task_utime(p));
- p->prev_stime = max(p->prev_stime, clock_t_to_cputime(stime));
+ if (stime >= 0)
+ p->prev_stime = max(p->prev_stime, clock_t_to_cputime(stime));
+
return p->prev_stime;
}
#endif
struct acpi_processor_power {
struct cpuidle_device dev;
struct acpi_processor_cx *state;
- struct acpi_processor_cx *bm_state;
unsigned long bm_check_timestamp;
u32 default_state;
u32 bm_activity;
extern unsigned long sclk_to_usecs(unsigned long sclk);
extern unsigned long usecs_to_sclk(unsigned long usecs);
-extern void dump_thread(struct pt_regs *regs, struct user *dump);
-extern void dump_bfin_regs(struct pt_regs *fp, void *retaddr);
+extern void dump_bfin_process(struct pt_regs *regs);
+extern void dump_bfin_mem(void *retaddr);
extern void dump_bfin_trace_buffer(void);
extern int init_arch_irq(void);
extern int read_iloc(void);
extern int bfin_console_init(void);
extern asmlinkage void lower_to_irq14(void);
+extern asmlinkage void bfin_return_from_exception(void);
extern void init_exception_vectors(void);
extern void init_dma(void);
extern void program_IAR(void);
* 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
+#ifndef __ASM_CPLBINIT_H__
+#define __ASM_CPLBINIT_H__
+
#include <asm/blackfin.h>
#include <asm/cplb.h>
u16 size;
};
-extern u_long icplb_table[MAX_CPLBS+1];
-extern u_long dcplb_table[MAX_CPLBS+1];
+extern u_long icplb_table[];
+extern u_long dcplb_table[];
/* Till here we are discussing about the static memory management model.
* However, the operating envoronments commonly define more CPLB
* This is how Page descriptor Table is implemented in uClinux/Blackfin.
*/
-#ifdef CONFIG_CPLB_SWITCH_TAB_L1
-extern u_long ipdt_table[MAX_SWITCH_I_CPLBS+1]__attribute__((l1_data));
-extern u_long dpdt_table[MAX_SWITCH_D_CPLBS+1]__attribute__((l1_data));
-
-#ifdef CONFIG_CPLB_INFO
-extern u_long ipdt_swapcount_table[MAX_SWITCH_I_CPLBS]__attribute__((l1_data));
-extern u_long dpdt_swapcount_table[MAX_SWITCH_D_CPLBS]__attribute__((l1_data));
-#endif /* CONFIG_CPLB_INFO */
-
-#else
-
-extern u_long ipdt_table[MAX_SWITCH_I_CPLBS+1];
-extern u_long dpdt_table[MAX_SWITCH_D_CPLBS+1];
-
+extern u_long ipdt_table[];
+extern u_long dpdt_table[];
#ifdef CONFIG_CPLB_INFO
-extern u_long ipdt_swapcount_table[MAX_SWITCH_I_CPLBS];
-extern u_long dpdt_swapcount_table[MAX_SWITCH_D_CPLBS];
-#endif /* CONFIG_CPLB_INFO */
-
-#endif /*CONFIG_CPLB_SWITCH_TAB_L1*/
+extern u_long ipdt_swapcount_table[];
+extern u_long dpdt_swapcount_table[];
+#endif
extern unsigned long reserved_mem_dcache_on;
extern unsigned long reserved_mem_icache_on;
extern void generate_cpl_tables(void);
+
+#endif
-#ifndef _BLACKFIN_DELAY_H
-#define _BLACKFIN_DELAY_H
-
-static inline void __delay(unsigned long loops)
-{
-
-/* FIXME: Currently the assembler doesn't recognize Loop Register Clobbers,
- uncomment this as soon those are implemented */
/*
- __asm__ __volatile__ ( "\t LSETUP (1f,1f) LC0= %0\n\t"
- "1:\t NOP;\n\t"
- : :"a" (loops)
- : "LT0","LB0","LC0");
+ * delay.h - delay functions
+ *
+ * Copyright (c) 2004-2007 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __ASM_DELAY_H__
+#define __ASM_DELAY_H__
-*/
+#include <asm/mach/anomaly.h>
- __asm__ __volatile__("[--SP] = LC0;\n\t"
- "[--SP] = LT0;\n\t"
- "[--SP] = LB0;\n\t"
- "LSETUP (1f,1f) LC0 = %0;\n\t"
- "1:\t NOP;\n\t"
- "LB0 = [SP++];\n\t"
- "LT0 = [SP++];\n\t"
- "LC0 = [SP++];\n"
- :
- :"a" (loops));
+static inline void __delay(unsigned long loops)
+{
+ if (ANOMALY_05000312) {
+ /* Interrupted loads to loop registers -> bad */
+ unsigned long tmp;
+ __asm__ __volatile__(
+ "[--SP] = LC0;"
+ "[--SP] = LT0;"
+ "[--SP] = LB0;"
+ "LSETUP (1f,1f) LC0 = %1;"
+ "1: NOP;"
+ /* We take advantage of the fact that LC0 is 0 at
+ * the end of the loop. Otherwise we'd need some
+ * NOPs after the CLI here.
+ */
+ "CLI %0;"
+ "LB0 = [SP++];"
+ "LT0 = [SP++];"
+ "LC0 = [SP++];"
+ "STI %0;"
+ : "=d" (tmp)
+ : "a" (loops)
+ );
+ } else
+ __asm__ __volatile__ (
+ "LSETUP(1f, 1f) LC0 = %0;"
+ "1: NOP;"
+ :
+ : "a" (loops)
+ : "LT0", "LB0", "LC0"
+ );
}
#include <linux/param.h> /* needed for HZ */
__delay(usecs * loops_per_jiffy / (1000000 / HZ));
}
-#endif /* defined(_BLACKFIN_DELAY_H) */
+#endif
extern void insb(unsigned long port, void *addr, unsigned long count);
extern void insw(unsigned long port, void *addr, unsigned long count);
extern void insl(unsigned long port, void *addr, unsigned long count);
+extern void insl_16(unsigned long port, void *addr, unsigned long count);
extern void dma_outsb(unsigned long port, const void *addr, unsigned short count);
extern void dma_outsw(unsigned long port, const void *addr, unsigned short count);
#define GPIO_IRQ_BASE IRQ_PF0
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PH15+1)
-#else
-#define NR_IRQS (SYS_IRQS+1)
-#endif
#define IVG7 7
#define IVG8 8
/* Boot ROM Memory */
#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x8000
/* Level 1 Memory */
/* Scratch Pad Memory */
-#if defined(CONFIG_BF527) || defined(CONFIG_BF536) || defined(CONFIG_BF534)
#define L1_SCRATCH_START 0xFFB00000
#define L1_SCRATCH_LENGTH 0x1000
-#endif
#endif /* _MEM_MAP_527_H_ */
#define GPIO_IRQ_BASE IRQ_PF0
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PF15+1)
-#else
-#define NR_IRQS SYS_IRQS
-#endif
#define IVG7 7
#define IVG8 8
-
/*
* File: include/asm-blackfin/mach-bf533/mem_map.h
* Based on:
/* Boot ROM Memory */
#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x400
/* Level 1 Memory */
/* Scratch Pad Memory */
-#if defined(CONFIG_BF533) || defined(CONFIG_BF532) || defined(CONFIG_BF531)
#define L1_SCRATCH_START 0xFFB00000
#define L1_SCRATCH_LENGTH 0x1000
-#endif
#endif /* _MEM_MAP_533_H_ */
#define GPIO_IRQ_BASE IRQ_PF0
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PH15+1)
-#else
-#define NR_IRQS (IRQ_UART1_ERROR+1)
-#endif
#define IVG7 7
#define IVG8 8
/* Boot ROM Memory */
#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x800
/* Level 1 Memory */
/* Scratch Pad Memory */
-#if defined(CONFIG_BF537) || defined(CONFIG_BF536) || defined(CONFIG_BF534)
#define L1_SCRATCH_START 0xFFB00000
#define L1_SCRATCH_LENGTH 0x1000
-#endif
#endif /* _MEM_MAP_537_H_ */
#define AMGCTLVAL (V_AMBEN | V_AMCKEN)
-#ifdef CONFIG_BF542
-#define CPU "BF542"
-#define CPUID 0x027c8000
-#endif
-#ifdef CONFIG_BF544
-#define CPU "BF544"
-#define CPUID 0x027c8000
-#endif
-#ifdef CONFIG_BF548
-#define CPU "BF548"
-#define CPUID 0x027c6000
-#endif
-#ifdef CONFIG_BF549
-#define CPU "BF549"
-#endif
-#ifndef CPU
-#define CPU "UNKNOWN"
-#define CPUID 0x0
+#if defined(CONFIG_BF542)
+# define CPU "BF542"
+# define CPUID 0x027c8000
+#elif defined(CONFIG_BF544)
+# define CPU "BF544"
+# define CPUID 0x027c8000
+#elif defined(CONFIG_BF547)
+# define CPU "BF547"
+#elif defined(CONFIG_BF548)
+# define CPU "BF548"
+# define CPUID 0x027c6000
+#elif defined(CONFIG_BF549)
+# define CPU "BF549"
+#else
+# define CPU "UNKNOWN"
+# define CPUID 0x0
#endif
#endif /* __MACH_BF48_H__ */
/* Bit masks for HOST_STATUS */
-#define READY 0x1 /* DMA Ready */
+#define DMA_READY 0x1 /* DMA Ready */
#define FIFOFULL 0x2 /* FIFO Full */
#define FIFOEMPTY 0x4 /* FIFO Empty */
#define COMPLETE 0x8 /* DMA Complete */
/* Bit masks for HOST_STATUS */
-#define READY 0x1 /* DMA Ready */
+#define DMA_READY 0x1 /* DMA Ready */
#define FIFOFULL 0x2 /* FIFO Full */
#define FIFOEMPTY 0x4 /* FIFO Empty */
#define COMPLETE 0x8 /* DMA Complete */
#define GPIO_IRQ_BASE IRQ_PA0
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PJ15+1)
-#else
-#define NR_IRQS (SYS_IRQS+1)
-#endif
/* For compatibility reasons with existing code */
/* Boot ROM Memory */
#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x1000
+
+/* L1 Instruction ROM */
+
+#define L1_ROM_START 0xFFA14000
+#define L1_ROM_LENGTH 0x10000
/* Level 1 Memory */
#define BFIN_DSUPBANKS 0
#endif /*CONFIG_BFIN_DCACHE*/
+/* Level 2 Memory */
+#if !defined(CONFIG_BF542)
+# define L2_START 0xFEB00000
+# if defined(CONFIG_BF544)
+# define L2_LENGTH 0x10000
+# else
+# define L2_LENGTH 0x20000
+# endif
+#endif
+
/* Scratch Pad Memory */
-#if defined(CONFIG_BF54x)
#define L1_SCRATCH_START 0xFFB00000
#define L1_SCRATCH_LENGTH 0x1000
-#endif
#endif/* _MEM_MAP_548_H_ */
#define SUPPORTED_REVID 0x3
#define OFFSET_(x) ((x) & 0x0000FFFF)
-#define L1_ISRAM 0xFFA00000
-#define L1_ISRAM_END 0xFFA04000
-#define DATA_BANKA_SRAM 0xFF800000
-#define DATA_BANKA_SRAM_END 0xFF804000
-#define DATA_BANKB_SRAM 0xFF900000
-#define DATA_BANKB_SRAM_END 0xFF904000
-#define L1_DSRAMA 0xFF800000
-#define L1_DSRAMA_END 0xFF804000
-#define L1_DSRAMB 0xFF900000
-#define L1_DSRAMB_END 0xFF904000
-#define L2_SRAM 0xFEB00000
-#define L2_SRAM_END 0xFEB20000
-#define AMB_FLASH 0x20000000
-#define AMB_FLASH_END 0x21000000
-#define AMB_FLASH_LENGTH 0x01000000
-#define L1_ISRAM_LENGTH 0x4000
-#define L1_DSRAMA_LENGTH 0x4000
-#define L1_DSRAMB_LENGTH 0x4000
-#define L2_SRAM_LENGTH 0x20000
/*some misc defines*/
#define IMASK_IVG15 0x8000
/* For MMR's that are reserved on Core B, set up defines to better integrate with other ports */
#define SWRST SICA_SWRST
#define SYSCR SICA_SYSCR
+#define DOUBLE_FAULT (DOUBLE_FAULT_B|DOUBLE_FAULT_A)
#define RESET_DOUBLE (SWRST_DBL_FAULT_B|SWRST_DBL_FAULT_A)
#define RESET_WDOG (SWRST_WDT_B|SWRST_WDT_A)
#define RESET_SOFTWARE (SWRST_OCCURRED)
#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
/* SWRST Mask */
-#define SYSTEM_RESET 0x00000007 /* Initiates a system software reset */
-#define SWRST_DBL_FAULT_B 0x00000800 /* SWRST Core B Double Fault */
-#define SWRST_DBL_FAULT_A 0x00001000 /* SWRST Core A Double Fault */
-#define SWRST_WDT_B 0x00002000 /* SWRST Watchdog B */
-#define SWRST_WDT_A 0x00004000 /* SWRST Watchdog A */
-#define SWRST_OCCURRED 0x00008000 /* SWRST Status */
+#define SYSTEM_RESET 0x0007 /* Initiates a system software reset */
+#define DOUBLE_FAULT_A 0x0008 /* Core A Double Fault Causes Reset */
+#define DOUBLE_FAULT_B 0x0010 /* Core B Double Fault Causes Reset */
+#define SWRST_DBL_FAULT_A 0x0800 /* SWRST Core A Double Fault */
+#define SWRST_DBL_FAULT_B 0x1000 /* SWRST Core B Double Fault */
+#define SWRST_WDT_B 0x2000 /* SWRST Watchdog B */
+#define SWRST_WDT_A 0x4000 /* SWRST Watchdog A */
+#define SWRST_OCCURRED 0x8000 /* SWRST Status */
/* ************* SYSTEM INTERRUPT CONTROLLER MASKS ***************** */
#define GPIO_IRQ_BASE IRQ_PF0
-#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
#define NR_IRQS (IRQ_PF47 + 1)
-#else
-#define NR_IRQS SYS_IRQS
-#endif
#define IVG7 7
#define IVG8 8
#define ASYNC_BANK0_BASE 0x20000000 /* Async Bank 0 */
#define ASYNC_BANK0_SIZE 0x04000000 /* 64M */
+/* Boot ROM Memory */
+
+#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x800
+
/* Level 1 Memory */
#ifdef CONFIG_BFIN_ICACHE
/* Scratch Pad Memory */
-#if defined(CONFIG_BF561)
#define L1_SCRATCH_START 0xFFB00000
#define L1_SCRATCH_LENGTH 0x1000
-#endif
#endif /* _MEM_MAP_533_H_ */
#endif
#define bfin_read8(addr) ({ \
- uint8_t __v; \
+ uint32_t __v; \
__asm__ __volatile__( \
NOP_PAD_ANOMALY_05000198 \
"%0 = b[%1] (z);" \
__v; })
#define bfin_read16(addr) ({ \
- uint16_t __v; \
+ uint32_t __v; \
__asm__ __volatile__( \
NOP_PAD_ANOMALY_05000198 \
"%0 = w[%1] (z);" \
NOP_PAD_ANOMALY_05000198 \
"b[%0] = %1;" \
: \
- : "a" (addr), "d" (val) \
+ : "a" (addr), "d" ((uint8_t)(val)) \
: "memory" \
)
NOP_PAD_ANOMALY_05000198 \
"w[%0] = %1;" \
: \
- : "a" (addr), "d" (val) \
+ : "a" (addr), "d" ((uint16_t)(val)) \
: "memory" \
)
/* This handles the memory map.. */
-#ifdef CONFIG_BFIN
+#ifdef CONFIG_BLACKFIN
#define PAGE_OFFSET_RAW 0x00000000
#endif
#ifndef _BLACKFIN_STRING_H_
#define _BLACKFIN_STRING_H_
+#include <linux/types.h>
+
#ifdef __KERNEL__ /* only set these up for kernel code */
#define __HAVE_ARCH_STRCPY
#ifndef __ASSEMBLY__
-#define HWC_x2 "System MMR Error\nAn error occurred due to an invalid access to an System MMR location\nPossible reason: a 32-bit register is accessed with a 16-bit instruction,\nor a 16-bit register is accessed with a 32-bit instruction.\n"
-#define HWC_x3 "External Memory Addressing Error\n"
-#define HWC_x12 "Performance Monitor Overflow\n"
-#define HWC_x18 "RAISE 5 instruction\n Software issued a RAISE 5 instruction to invoke the Hardware\n"
-#define HWC_default "Reserved\n"
-
-#define EXC_0x03 "Application stack overflow\n - Please increase the stack size of the application using elf2flt -s option,\n and/or reduce the stack use of the application.\n"
-#define EXC_0x10 "Single step\n - When the processor is in single step mode, every instruction\n generates an exception. Primarily used for debugging.\n"
-#define EXC_0x11 "Exception caused by a trace buffer full condition\n - The processor takes this exception when the trace\n buffer overflows (only when enabled by the Trace Unit Control register).\n"
-#define EXC_0x21 "Undefined instruction\n - May be used to emulate instructions that are not defined for\n a particular processor implementation.\n"
-#define EXC_0x22 "Illegal instruction combination\n - See section for multi-issue rules in the ADSP-BF53x Blackfin\n Processor Instruction Set Reference.\n"
-#define EXC_0x23 "Data access CPLB protection violation\n - Attempted read or write to Supervisor resource,\n or illegal data memory access. \n"
-#define EXC_0x24 "Data access misaligned address violation\n - Attempted misaligned data memory or data cache access.\n"
-#define EXC_0x25 "Unrecoverable event\n - For example, an exception generated while processing a previous exception.\n"
-#define EXC_0x26 "Data access CPLB miss\n - Used by the MMU to signal a CPLB miss on a data access.\n"
-#define EXC_0x27 "Data access multiple CPLB hits\n - More than one CPLB entry matches data fetch address.\n"
-#define EXC_0x28 "Program Sequencer Exception caused by an emulation watchpoint match\n - There is a watchpoint match, and one of the EMUSW\n bits in the Watchpoint Instruction Address Control register (WPIACTL) is set.\n"
-#define EXC_0x2A "Instruction fetch misaligned address violation\n - Attempted misaligned instruction cache fetch. On a misaligned instruction fetch exception,\n the return address provided in RETX is the destination address which is misaligned, rather than the address of the offending instruction.\n"
-#define EXC_0x2B "CPLB protection violation\n - Illegal instruction fetch access (memory protection violation).\n"
-#define EXC_0x2C "Instruction fetch CPLB miss\n - CPLB miss on an instruction fetch.\n"
-#define EXC_0x2D "Instruction fetch multiple CPLB hits\n - More than one CPLB entry matches instruction fetch address.\n"
-#define EXC_0x2E "Illegal use of supervisor resource\n - Attempted to use a Supervisor register or instruction from User mode.\n Supervisor resources are registers and instructions that are reserved\n for Supervisor use: Supervisor only registers, all MMRs, and Supervisor\n only instructions.\n"
+#define HWC_x2(level) \
+ "System MMR Error\n" \
+ level " - An error occurred due to an invalid access to an System MMR location\n" \
+ level " Possible reason: a 32-bit register is accessed with a 16-bit instruction\n" \
+ level " or a 16-bit register is accessed with a 32-bit instruction.\n"
+#define HWC_x3(level) \
+ "External Memory Addressing Error\n"
+#define HWC_x12(level) \
+ "Performance Monitor Overflow\n"
+#define HWC_x18(level) \
+ "RAISE 5 instruction\n" \
+ level " Software issued a RAISE 5 instruction to invoke the Hardware\n"
+#define HWC_default(level) \
+ "Reserved\n"
+#define EXC_0x03(level) \
+ "Application stack overflow\n" \
+ level " - Please increase the stack size of the application using elf2flt -s option,\n" \
+ level " and/or reduce the stack use of the application.\n"
+#define EXC_0x10(level) \
+ "Single step\n" \
+ level " - When the processor is in single step mode, every instruction\n" \
+ level " generates an exception. Primarily used for debugging.\n"
+#define EXC_0x11(level) \
+ "Exception caused by a trace buffer full condition\n" \
+ level " - The processor takes this exception when the trace\n" \
+ level " buffer overflows (only when enabled by the Trace Unit Control register).\n"
+#define EXC_0x21(level) \
+ "Undefined instruction\n" \
+ level " - May be used to emulate instructions that are not defined for\n" \
+ level " a particular processor implementation.\n"
+#define EXC_0x22(level) \
+ "Illegal instruction combination\n" \
+ level " - See section for multi-issue rules in the ADSP-BF53x Blackfin\n" \
+ level " Processor Instruction Set Reference.\n"
+#define EXC_0x23(level) \
+ "Data access CPLB protection violation\n" \
+ level " - Attempted read or write to Supervisor resource,\n" \
+ level " or illegal data memory access. \n"
+#define EXC_0x24(level) \
+ "Data access misaligned address violation\n" \
+ level " - Attempted misaligned data memory or data cache access.\n"
+#define EXC_0x25(level) \
+ "Unrecoverable event\n" \
+ level " - For example, an exception generated while processing a previous exception.\n"
+#define EXC_0x26(level) \
+ "Data access CPLB miss\n" \
+ level " - Used by the MMU to signal a CPLB miss on a data access.\n"
+#define EXC_0x27(level) \
+ "Data access multiple CPLB hits\n" \
+ level " - More than one CPLB entry matches data fetch address.\n"
+#define EXC_0x28(level) \
+ "Program Sequencer Exception caused by an emulation watchpoint match\n" \
+ level " - There is a watchpoint match, and one of the EMUSW\n" \
+ level " bits in the Watchpoint Instruction Address Control register (WPIACTL) is set.\n"
+#define EXC_0x2A(level) \
+ "Instruction fetch misaligned address violation\n" \
+ level " - Attempted misaligned instruction cache fetch. On a misaligned instruction fetch\n" \
+ level " exception, the return address provided in RETX is the destination address which is\n" \
+ level " misaligned, rather than the address of the offending instruction.\n"
+#define EXC_0x2B(level) \
+ "CPLB protection violation\n" \
+ level " - Illegal instruction fetch access (memory protection violation).\n"
+#define EXC_0x2C(level) \
+ "Instruction fetch CPLB miss\n" \
+ level " - CPLB miss on an instruction fetch.\n"
+#define EXC_0x2D(level) \
+ "Instruction fetch multiple CPLB hits\n" \
+ level " - More than one CPLB entry matches instruction fetch address.\n"
+#define EXC_0x2E(level) \
+ "Illegal use of supervisor resource\n" \
+ level " - Attempted to use a Supervisor register or instruction from User mode.\n" \
+ level " Supervisor resources are registers and instructions that are reserved\n" \
+ level " for Supervisor use: Supervisor only registers, all MMRs, and Supervisor\n" \
+ level " only instructions.\n"
#endif /* __ASSEMBLY__ */
#endif /* _BFIN_TRAPS_H */
* then it defines them prior including asm-generic/resource.h. )
*/
-#define RLIMIT_CPU 0 /* CPU time in ms */
+#define RLIMIT_CPU 0 /* CPU time in sec */
#define RLIMIT_FSIZE 1 /* Maximum filesize */
#define RLIMIT_DATA 2 /* max data size */
#define RLIMIT_STACK 3 /* max stack size */
#define acpi_noirq 0 /* ACPI always enabled on IA64 */
#define acpi_pci_disabled 0 /* ACPI PCI always enabled on IA64 */
#define acpi_strict 1 /* no ACPI spec workarounds on IA64 */
+#define acpi_processor_cstate_check(x) (x) /* no idle limits on IA64 :) */
static inline void disable_acpi(void) { }
const char *acpi_get_sysname (void);
#define TIF_NEED_RESCHED 2 /* rescheduling necessary */
#define TIF_SINGLESTEP 3 /* restore singlestep on return to user mode */
#define TIF_IRET 4 /* return with iret */
-#define TIF_POLLING_NRFLAG 16 /* true if poll_idle() is polling TIF_NEED_RESCHED */
- /* 31..28 fault code */
-#define TIF_MEMDIE 17
+#define TIF_RESTORE_SIGMASK 8 /* restore signal mask in do_signal() */
+#define TIF_USEDFPU 16 /* FPU was used by this task this quantum (SMP) */
+#define TIF_POLLING_NRFLAG 17 /* true if poll_idle() is polling TIF_NEED_RESCHED */
+#define TIF_MEMDIE 18 /* OOM killer killed process */
+#define TIF_FREEZE 19 /* is freezing for suspend */
#define _TIF_SYSCALL_TRACE (1<<TIF_SYSCALL_TRACE)
#define _TIF_SIGPENDING (1<<TIF_SIGPENDING)
#define _TIF_NEED_RESCHED (1<<TIF_NEED_RESCHED)
#define _TIF_SINGLESTEP (1<<TIF_SINGLESTEP)
#define _TIF_IRET (1<<TIF_IRET)
+#define _TIF_RESTORE_SIGMASK (1<<TIF_RESTORE_SIGMASK)
+#define _TIF_USEDFPU (1<<TIF_USEDFPU)
#define _TIF_POLLING_NRFLAG (1<<TIF_POLLING_NRFLAG)
+#define _TIF_FREEZE (1<<TIF_FREEZE)
#define _TIF_WORK_MASK 0x0000FFFE /* work to do on interrupt/exception return */
#define _TIF_ALLWORK_MASK 0x0000FFFF /* work to do on any return to u-space */
#define __NR_mq_getsetattr (__NR_mq_open+5)
#define __NR_kexec_load 283
#define __NR_waitid 284
+/* 285 is unused */
+#define __NR_add_key 286
+#define __NR_request_key 287
+#define __NR_keyctl 288
+#define __NR_ioprio_set 289
+#define __NR_ioprio_get 290
+#define __NR_inotify_init 291
+#define __NR_inotify_add_watch 292
+#define __NR_inotify_rm_watch 293
+#define __NR_migrate_pages 294
+#define __NR_openat 295
+#define __NR_mkdirat 296
+#define __NR_mknodat 297
+#define __NR_fchownat 298
+#define __NR_futimesat 299
+#define __NR_fstatat64 300
+#define __NR_unlinkat 301
+#define __NR_renameat 302
+#define __NR_linkat 303
+#define __NR_symlinkat 304
+#define __NR_readlinkat 305
+#define __NR_fchmodat 306
+#define __NR_faccessat 307
+#define __NR_pselect6 308
+#define __NR_ppoll 309
+#define __NR_unshare 310
+#define __NR_set_robust_list 311
+#define __NR_get_robust_list 312
+#define __NR_splice 313
+#define __NR_sync_file_range 314
+#define __NR_tee 315
+#define __NR_vmsplice 316
+#define __NR_move_pages 317
+#define __NR_getcpu 318
+#define __NR_epoll_pwait 319
+#define __NR_utimensat 320
+#define __NR_signalfd 321
+#define __NR_timerfd 322
+#define __NR_eventfd 323
+#define __NR_fallocate 324
#ifdef __KERNEL__
-#define NR_syscalls 285
+#define NR_syscalls 325
#define __ARCH_WANT_IPC_PARSE_VERSION
#define __ARCH_WANT_STAT64
#define __ARCH_WANT_SYS_OLDUMOUNT
#define __ARCH_WANT_SYS_RT_SIGACTION
+#define __IGNORE_lchown
+#define __IGNORE_setuid
+#define __IGNORE_getuid
+#define __IGNORE_setgid
+#define __IGNORE_getgid
+#define __IGNORE_geteuid
+#define __IGNORE_getegid
+#define __IGNORE_fcntl
+#define __IGNORE_setreuid
+#define __IGNORE_setregid
+#define __IGNORE_getrlimit
+#define __IGNORE_getgroups
+#define __IGNORE_setgroups
+#define __IGNORE_select
+#define __IGNORE_mmap
+#define __IGNORE_fchown
+#define __IGNORE_setfsuid
+#define __IGNORE_setfsgid
+#define __IGNORE_setresuid
+#define __IGNORE_getresuid
+#define __IGNORE_setresgid
+#define __IGNORE_getresgid
+#define __IGNORE_chown
+
/*
* "Conditional" syscalls
*
+++ /dev/null
-/*
- * 8253/8254 Programmable Interval Timer
- */
-
-#ifndef _8253PIT_H
-#define _8253PIT_H
-
-#define PIT_TICK_RATE 1193182UL
-
-#endif
#define MAX_DMA_ADDRESS (PAGE_OFFSET + 0x01000000)
#endif
#define MAX_DMA_PFN PFN_DOWN(virt_to_phys((void *)MAX_DMA_ADDRESS))
+#define MAX_DMA32_PFN (1UL << (32 - PAGE_SHIFT))
/* 8237 DMA controllers */
#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
" .set mips0 \n" \
" .section .fixup,\"ax\" \n" \
"4: li %0, %6 \n" \
- " j 2b \n" \
+ " j 3b \n" \
" .previous \n" \
" .section __ex_table,\"a\" \n" \
" "__UA_ADDR "\t1b, 4b \n" \
" .set mips0 \n" \
" .section .fixup,\"ax\" \n" \
"4: li %0, %6 \n" \
- " j 2b \n" \
+ " j 3b \n" \
" .previous \n" \
" .section __ex_table,\"a\" \n" \
" "__UA_ADDR "\t1b, 4b \n" \
}
#endif
-#endif
+#endif /* _ASM_FUTEX_H */
#define PIT_CH0 0x40
#define PIT_CH2 0x42
+#define PIT_TICK_RATE 1193182UL
+
extern spinlock_t i8253_lock;
extern void setup_pit_timer(void);
* CPU interrupts are 0 ... 7
*/
- CRIME_IRQ_BASE = MIPS_CPU_IRQ_BASE,
+ CRIME_IRQ_BASE = MIPS_CPU_IRQ_BASE + 8,
/*
* MACE
if (cpu_has_dsp) \
__save_dsp(prev); \
(last) = resume(prev, next, task_thread_info(next)); \
+} while (0)
+
+#define finish_arch_switch(prev) \
+do { \
if (cpu_has_dsp) \
__restore_dsp(current); \
if (cpu_has_userlocal) \
- write_c0_userlocal(task_thread_info(current)->tp_value);\
-} while(0)
+ write_c0_userlocal(current_thread_info()->tp_value); \
+} while (0)
static inline unsigned long __xchg_u32(volatile int * m, unsigned int val)
{
* Initialize the calling CPU's compare interrupt as clockevent device
*/
#ifdef CONFIG_CEVT_R4K
-extern void mips_clockevent_init(void);
+extern int mips_clockevent_init(void);
extern unsigned int __weak get_c0_compare_int(void);
#else
-static inline void mips_clockevent_init(void)
+static inline int mips_clockevent_init(void)
+{
+ return -ENXIO;
+}
+#endif
+
+/*
+ * Initialize the count register as a clocksource
+ */
+#ifdef CONFIG_CEVT_R4K
+extern void init_mips_clocksource(void);
+#else
+static inline void init_mips_clocksource(void)
{
}
#endif
#define PPC_MEMSTART 0
+#ifdef CONFIG_NOT_COHERENT_CACHE
+#define ARCH_KMALLOC_MINALIGN L1_CACHE_BYTES
+#endif
+
#ifndef __ASSEMBLY__
/*
* The basic type of a PTE - 64 bits for those CPUs with > 32 bit
return PCI_DN(busdn)->phb;
}
-extern void pcibios_free_controller(struct pci_controller *phb);
extern void isa_bridge_find_early(struct pci_controller *hose);
pci_process_bridge_OF_ranges(struct pci_controller *hose,
struct device_node *dev, int primary);
-/* Allocate a new PCI host bridge structure */
+/* Allocate & free a PCI host bridge structure */
extern struct pci_controller *
pcibios_alloc_controller(struct device_node *dev);
+extern void pcibios_free_controller(struct pci_controller *phb);
+
#ifdef CONFIG_PCI
extern unsigned long pci_address_to_pio(phys_addr_t address);
extern int pcibios_vaddr_is_ioport(void __iomem *address);
extern void rtas_restart(char *cmd);
extern void rtas_power_off(void);
extern void rtas_halt(void);
-extern void rtas_os_term(char *str);
+extern void rtas_panic_msg(char *str);
+extern void rtas_os_term(void);
extern int rtas_get_sensor(int sensor, int index, int *state);
extern int rtas_get_power_level(int powerdomain, int *level);
extern int rtas_set_power_level(int powerdomain, int level, int *setlevel);
/* those additional ones don't have to be located anywhere
* special as they were not part of the original systemcfg
*/
+ __u32 dcache_block_size; /* L1 d-cache block size */
+ __u32 icache_block_size; /* L1 i-cache block size */
+ __u32 dcache_log_block_size; /* L1 d-cache log block size */
+ __u32 icache_log_block_size; /* L1 i-cache log block size */
__s32 wtom_clock_sec; /* Wall to monotonic clock */
__s32 wtom_clock_nsec;
__u32 syscall_map_64[SYSCALL_MAP_SIZE]; /* map of syscalls */
__s32 wtom_clock_sec; /* Wall to monotonic clock */
__s32 wtom_clock_nsec;
__u32 syscall_map_32[SYSCALL_MAP_SIZE]; /* map of syscalls */
+ __u32 dcache_block_size; /* L1 d-cache block size */
+ __u32 icache_block_size; /* L1 i-cache block size */
+ __u32 dcache_log_block_size; /* L1 d-cache log block size */
+ __u32 icache_log_block_size; /* L1 i-cache log block size */
};
#endif /* CONFIG_PPC64 */
#define arch_align_stack(x) (x)
+#ifdef CONFIG_TRACE_IRQFLAGS
+extern psw_t sysc_restore_trace_psw;
+extern psw_t io_restore_trace_psw;
+#endif
+
#endif /* __KERNEL__ */
#endif
extern void __flush_invalidate_region(void *start, int size);
#endif
-#ifdef CONFIG_CPU_SH4
+#if defined(CONFIG_CPU_SH4) && !defined(CONFIG_CACHE_OFF)
extern void copy_to_user_page(struct vm_area_struct *vma,
struct page *page, unsigned long vaddr, void *dst, const void *src,
unsigned long len);
+#ifndef _ASM_X86_ACPI_H
+#define _ASM_X86_ACPI_H
+
#ifdef CONFIG_X86_32
# include "acpi_32.h"
#else
# include "acpi_64.h"
#endif
+
+#include <asm/processor.h>
+
+/*
+ * Check if the CPU can handle C2 and deeper
+ */
+static inline unsigned int acpi_processor_cstate_check(unsigned int max_cstate)
+{
+ /*
+ * Early models (<=5) of AMD Opterons are not supposed to go into
+ * C2 state.
+ *
+ * Steppings 0x0A and later are good
+ */
+ if (boot_cpu_data.x86 == 0x0F &&
+ boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
+ boot_cpu_data.x86_model <= 0x05 &&
+ boot_cpu_data.x86_mask < 0x0A)
+ return 1;
+ else
+ return max_cstate;
+}
+
+#endif
#else /* !CONFIG_X86_LOCAL_APIC */
static inline void lapic_shutdown(void) { }
+#define local_apic_timer_c2_ok 1
#endif /* !CONFIG_X86_LOCAL_APIC */
int acpi_register_gsi (u32 gsi, int triggering, int polarity);
int acpi_gsi_to_irq (u32 gsi, unsigned int *irq);
+#ifdef CONFIG_X86_IO_APIC
+extern int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity);
+#else
+#define acpi_get_override_irq(bus, trigger, polarity) (-1)
+#endif
/*
* This function undoes the effect of one call to acpi_register_gsi().
* If this matches the last registration, any IRQ resources for gsi
struct kobject kobj;
struct completion kobj_unregister;
void *governor_data;
+ struct cpuidle_state *safe_state;
};
DECLARE_PER_CPU(struct cpuidle_device *, cpuidle_devices);
#define KEY_DOLLAR 0x1b2
#define KEY_EURO 0x1b3
+#define KEY_FRAMEBACK 0x1b4 /* Consumer - transport controls */
+#define KEY_FRAMEFORWARD 0x1b5
+
+#define KEY_CONTEXT_MENU 0x1b6 /* GenDesc - system context menu */
+
#define KEY_DEL_EOL 0x1c0
#define KEY_DEL_EOS 0x1c1
#define KEY_INS_LINE 0x1c2
ATA_HORKAGE_HPA_SIZE = (1 << 6), /* native size off by one */
ATA_HORKAGE_IPM = (1 << 7), /* Link PM problems */
ATA_HORKAGE_IVB = (1 << 8), /* cbl det validity bit bugs */
+ ATA_HORKAGE_STUCK_ERR = (1 << 9), /* stuck ERR on next PACKET */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
extern void sata_print_link_status(struct ata_link *link);
extern void ata_port_probe(struct ata_port *);
-extern void __sata_phy_reset(struct ata_port *ap);
-extern void sata_phy_reset(struct ata_port *ap);
extern void ata_bus_reset(struct ata_port *ap);
extern int sata_set_spd(struct ata_link *link);
extern int sata_link_debounce(struct ata_link *link,
/*
* EH
*/
-extern void ata_eng_timeout(struct ata_port *ap);
-
extern void ata_port_schedule_eh(struct ata_port *ap);
extern int ata_link_abort(struct ata_link *link);
extern int ata_port_abort(struct ata_port *ap);
extern int nfs_wb_all(struct inode *inode);
extern int nfs_wb_nocommit(struct inode *inode);
extern int nfs_wb_page(struct inode *inode, struct page* page);
-extern int nfs_wb_page_priority(struct inode *inode, struct page* page, int how);
extern int nfs_wb_page_cancel(struct inode *inode, struct page* page);
#if defined(CONFIG_NFS_V3) || defined(CONFIG_NFS_V4)
extern int nfs_commit_inode(struct inode *, int);
#define SG_MAGIC 0x87654321
+/*
+ * We overload the LSB of the page pointer to indicate whether it's
+ * a valid sg entry, or whether it points to the start of a new scatterlist.
+ * Those low bits are there for everyone! (thanks mason :-)
+ */
+#define sg_is_chain(sg) ((sg)->page_link & 0x01)
+#define sg_is_last(sg) ((sg)->page_link & 0x02)
+#define sg_chain_ptr(sg) \
+ ((struct scatterlist *) ((sg)->page_link & ~0x03))
+
/**
* sg_assign_page - Assign a given page to an SG entry
* @sg: SG entry
BUG_ON((unsigned long) page & 0x03);
#ifdef CONFIG_DEBUG_SG
BUG_ON(sg->sg_magic != SG_MAGIC);
+ BUG_ON(sg_is_chain(sg));
#endif
sg->page_link = page_link | (unsigned long) page;
}
sg->length = len;
}
-#define sg_page(sg) ((struct page *) ((sg)->page_link & ~0x3))
+static inline struct page *sg_page(struct scatterlist *sg)
+{
+#ifdef CONFIG_DEBUG_SG
+ BUG_ON(sg->sg_magic != SG_MAGIC);
+ BUG_ON(sg_is_chain(sg));
+#endif
+ return (struct page *)((sg)->page_link & ~0x3);
+}
/**
* sg_set_buf - Set sg entry to point at given data
sg_set_page(sg, virt_to_page(buf), buflen, offset_in_page(buf));
}
-/*
- * We overload the LSB of the page pointer to indicate whether it's
- * a valid sg entry, or whether it points to the start of a new scatterlist.
- * Those low bits are there for everyone! (thanks mason :-)
- */
-#define sg_is_chain(sg) ((sg)->page_link & 0x01)
-#define sg_is_last(sg) ((sg)->page_link & 0x02)
-#define sg_chain_ptr(sg) \
- ((struct scatterlist *) ((sg)->page_link & ~0x03))
-
/**
* sg_next - return the next scatterlist entry in a list
* @sg: The current sg entry
#ifndef ARCH_HAS_SG_CHAIN
BUG();
#endif
+
+ /*
+ * offset and length are unused for chain entry. Clear them.
+ */
+ prv->offset = 0;
+ prv->length = 0;
+
/*
* Set lowest bit to indicate a link pointer, and make sure to clear
* the termination bit if it happens to be set.
return __alloc_skb(size, priority, 1, -1);
}
-extern void kfree_skbmem(struct sk_buff *skb);
extern struct sk_buff *skb_morph(struct sk_buff *dst, struct sk_buff *src);
extern struct sk_buff *skb_clone(struct sk_buff *skb,
gfp_t priority);
CTL_SLOTTABLE_TCP,
CTL_MIN_RESVPORT,
CTL_MAX_RESVPORT,
- CTL_SLOTTABLE_RDMA,
- CTL_RDMA_MAXINLINEREAD,
- CTL_RDMA_MAXINLINEWRITE,
- CTL_RDMA_WRITEPADDING,
- CTL_RDMA_MEMREG,
};
#endif /* _LINUX_SUNRPC_DEBUG_H_ */
#ifdef __KERNEL__
-/*
- * Socket transport setup operations
- */
-struct rpc_xprt *xs_setup_udp(struct xprt_create *args);
-struct rpc_xprt *xs_setup_tcp(struct xprt_create *args);
-
int init_socket_xprt(void);
void cleanup_socket_xprt(void);
CTL_ABI=9, /* Binary emulation */
CTL_CPU=10, /* CPU stuff (speed scaling, etc) */
CTL_ARLAN=254, /* arlan wireless driver */
- CTL_APPLDATA=2120, /* s390 appldata */
CTL_S390DBF=5677, /* s390 debug */
CTL_SUNRPC=7249, /* sunrpc debug */
CTL_PM=9899, /* frv power management */
VM_PANIC_ON_OOM=33, /* panic at out-of-memory */
VM_VDSO_ENABLED=34, /* map VDSO into new processes? */
VM_MIN_SLAB=35, /* Percent pages ignored by zone reclaim */
-
- /* s390 vm cmm sysctls */
- VM_CMM_PAGES=1111,
- VM_CMM_TIMED_PAGES=1112,
- VM_CMM_TIMEOUT=1113,
};
#define ADJ_TIMECONST 0x0020 /* pll time constant */
#define ADJ_TICK 0x4000 /* tick value */
#define ADJ_OFFSET_SINGLESHOT 0x8001 /* old-fashioned adjtime */
+#define ADJ_OFFSET_SS_READ 0xa001 /* read-only adjtime */
/* xntp 3.4 compatibility names */
#define MOD_OFFSET ADJ_OFFSET
do { if (ieee80211_debug_level & (level)) \
printk(KERN_DEBUG "ieee80211: %c %s " fmt, \
in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0)
+static inline bool ieee80211_ratelimit_debug(u32 level)
+{
+ return (ieee80211_debug_level & level) && net_ratelimit();
+}
#else
#define IEEE80211_DEBUG(level, fmt, args...) do {} while (0)
+static inline bool ieee80211_ratelimit_debug(u32 level)
+{
+ return false;
+}
#endif /* CONFIG_IEEE80211_DEBUG */
/* escape_essid() is intended to be used in debug (and possibly error)
if (size > PAGE_SIZE)
vfree(hashinfo->ehash_locks);
else
-#else
- kfree(hashinfo->ehash_locks);
#endif
+ kfree(hashinfo->ehash_locks);
hashinfo->ehash_locks = NULL;
}
}
#define FTPPORT __constant_htons(21)
#define FTPDATA __constant_htons(20)
-/*
- * IPVS sysctl variables under the /proc/sys/net/ipv4/vs/
- */
-#define NET_IPV4_VS 21
-
-enum {
- NET_IPV4_VS_DEBUG_LEVEL=1,
- NET_IPV4_VS_AMEMTHRESH=2,
- NET_IPV4_VS_AMDROPRATE=3,
- NET_IPV4_VS_DROP_ENTRY=4,
- NET_IPV4_VS_DROP_PACKET=5,
- NET_IPV4_VS_SECURE_TCP=6,
- NET_IPV4_VS_TO_ES=7,
- NET_IPV4_VS_TO_SS=8,
- NET_IPV4_VS_TO_SR=9,
- NET_IPV4_VS_TO_FW=10,
- NET_IPV4_VS_TO_TW=11,
- NET_IPV4_VS_TO_CL=12,
- NET_IPV4_VS_TO_CW=13,
- NET_IPV4_VS_TO_LA=14,
- NET_IPV4_VS_TO_LI=15,
- NET_IPV4_VS_TO_SA=16,
- NET_IPV4_VS_TO_UDP=17,
- NET_IPV4_VS_TO_ICMP=18,
- NET_IPV4_VS_LBLC_EXPIRE=19,
- NET_IPV4_VS_LBLCR_EXPIRE=20,
- NET_IPV4_VS_CACHE_BYPASS=22,
- NET_IPV4_VS_EXPIRE_NODEST_CONN=23,
- NET_IPV4_VS_SYNC_THRESHOLD=24,
- NET_IPV4_VS_NAT_ICMP_SEND=25,
- NET_IPV4_VS_EXPIRE_QUIESCENT_TEMPLATE=26,
- NET_IPV4_VS_LAST
-};
-
/*
* TCP State Values
*/
{
struct sk_buff *skb;
+ /* The TCP header must be at least 32-bit aligned. */
+ size = ALIGN(size, 4);
+
skb = alloc_skb_fclone(size + sk->sk_prot->max_header, gfp);
if (skb) {
skb->truesize += mem;
struct sock *sk)
{
__skb_insert(new, skb->prev, skb, &sk->sk_write_queue);
+
+ if (sk->sk_send_head == skb)
+ sk->sk_send_head = new;
}
static inline void tcp_unlink_write_queue(struct sk_buff *skb, struct sock *sk)
/* include/version.h. Generated by alsa/ksync script. */
#define CONFIG_SND_VERSION "1.0.15"
-#define CONFIG_SND_DATE " (Tue Oct 23 06:09:18 2007 UTC)"
+#define CONFIG_SND_DATE " (Tue Nov 20 19:16:42 2007 UTC)"
config UID16
bool "Enable 16-bit UID system calls" if EMBEDDED
- depends on ARM || BFIN || CRIS || FRV || H8300 || X86_32 || M68K || (S390 && !64BIT) || SUPERH || SPARC32 || (SPARC64 && SPARC32_COMPAT) || UML || (X86_64 && IA32_EMULATION)
+ depends on ARM || BLACKFIN || CRIS || FRV || H8300 || X86_32 || M68K || (S390 && !64BIT) || SUPERH || SPARC32 || (SPARC64 && SPARC32_COMPAT) || UML || (X86_64 && IA32_EMULATION)
default y
help
This enables the legacy 16-bit UID syscall wrappers.
* The acct_process() call is the workhorse of the process
* accounting system. The struct acct is built here and then written
* into the accounting file. This function should only be called from
- * do_exit().
+ * do_exit() or when switching to a different output file.
*/
/*
}
EXPORT_SYMBOL(unregister_module_notifier);
-/* We require a truly strong try_module_get() */
+/* We require a truly strong try_module_get(): 0 means failure due to
+ ongoing or failed initialization etc. */
static inline int strong_try_module_get(struct module *mod)
{
if (mod && mod->state == MODULE_STATE_COMING)
ret = __find_symbol(name, &owner, &crc,
!(mod->taints & TAINT_PROPRIETARY_MODULE));
if (ret) {
- /* use_module can fail due to OOM, or module unloading */
+ /* use_module can fail due to OOM,
+ or module initialization or unloading */
if (!check_version(sechdrs, versindex, name, mod, crc) ||
!use_module(mod, owner))
ret = 0;
return ret;
}
-/* Change all symbols so that sh_value encodes the pointer directly. */
+/* Change all symbols so that st_value encodes the pointer directly. */
static int simplify_symbols(Elf_Shdr *sechdrs,
unsigned int symindex,
const char *strtab,
u64 now = ktime_to_ns(ktime_get());
int cpu;
- SEQ_printf(m, "Sched Debug Version: v0.06-v22, %s %.*s\n",
+ SEQ_printf(m, "Sched Debug Version: v0.07, %s %.*s\n",
init_utsname()->release,
(int)strcspn(init_utsname()->version, " "),
init_utsname()->version);
/*
* Targeted preemption latency for CPU-bound tasks:
- * (default: 20ms * ilog(ncpus), units: nanoseconds)
+ * (default: 20ms * (1 + ilog(ncpus)), units: nanoseconds)
*
* NOTE: this latency value is not the same as the concept of
* 'timeslice length' - timeslices in CFS are of variable length
/*
* Minimal preemption granularity for CPU-bound tasks:
- * (default: 1 msec * ilog(ncpus), units: nanoseconds)
+ * (default: 4 msec * (1 + ilog(ncpus)), units: nanoseconds)
*/
-unsigned int sysctl_sched_min_granularity = 1000000ULL;
+unsigned int sysctl_sched_min_granularity = 4000000ULL;
/*
* is kept at sysctl_sched_latency / sysctl_sched_min_granularity
*/
-static unsigned int sched_nr_latency = 20;
+static unsigned int sched_nr_latency = 5;
/*
* After fork, child runs first. (default) If set to 0 then
/*
* SCHED_BATCH wake-up granularity.
- * (default: 10 msec * ilog(ncpus), units: nanoseconds)
+ * (default: 10 msec * (1 + ilog(ncpus)), units: nanoseconds)
*
* This option delays the preemption effects of decoupled workloads
* and reduces their over-scheduling. Synchronous workloads will still
/*
* SCHED_OTHER wake-up granularity.
- * (default: 10 msec * ilog(ncpus), units: nanoseconds)
+ * (default: 10 msec * (1 + ilog(ncpus)), units: nanoseconds)
*
* This option delays the preemption effects of decoupled workloads
* and reduces their over-scheduling. Synchronous workloads will still
{ VM_PANIC_ON_OOM, "panic_on_oom" },
{ VM_VDSO_ENABLED, "vdso_enabled" },
{ VM_MIN_SLAB, "min_slab_ratio" },
- { VM_CMM_PAGES, "cmm_pages" },
- { VM_CMM_TIMED_PAGES, "cmm_timed_pages" },
- { VM_CMM_TIMEOUT, "cmm_timeout" },
{}
};
{}
};
-
-static struct trans_ctl_table trans_net_ipv4_vs_table[] = {
- { NET_IPV4_VS_AMEMTHRESH, "amemthresh" },
- { NET_IPV4_VS_DEBUG_LEVEL, "debug_level" },
- { NET_IPV4_VS_AMDROPRATE, "am_droprate" },
- { NET_IPV4_VS_DROP_ENTRY, "drop_entry" },
- { NET_IPV4_VS_DROP_PACKET, "drop_packet" },
- { NET_IPV4_VS_SECURE_TCP, "secure_tcp" },
- { NET_IPV4_VS_TO_ES, "timeout_established" },
- { NET_IPV4_VS_TO_SS, "timeout_synsent" },
- { NET_IPV4_VS_TO_SR, "timeout_synrecv" },
- { NET_IPV4_VS_TO_FW, "timeout_finwait" },
- { NET_IPV4_VS_TO_TW, "timeout_timewait" },
- { NET_IPV4_VS_TO_CL, "timeout_close" },
- { NET_IPV4_VS_TO_CW, "timeout_closewait" },
- { NET_IPV4_VS_TO_LA, "timeout_lastack" },
- { NET_IPV4_VS_TO_LI, "timeout_listen" },
- { NET_IPV4_VS_TO_SA, "timeout_synack" },
- { NET_IPV4_VS_TO_UDP, "timeout_udp" },
- { NET_IPV4_VS_TO_ICMP, "timeout_icmp" },
- { NET_IPV4_VS_CACHE_BYPASS, "cache_bypass" },
- { NET_IPV4_VS_EXPIRE_NODEST_CONN, "expire_nodest_conn" },
- { NET_IPV4_VS_EXPIRE_QUIESCENT_TEMPLATE, "expire_quiescent_template" },
- { NET_IPV4_VS_SYNC_THRESHOLD, "sync_threshold" },
- { NET_IPV4_VS_NAT_ICMP_SEND, "nat_icmp_send" },
- { NET_IPV4_VS_LBLC_EXPIRE, "lblc_expiration" },
- { NET_IPV4_VS_LBLCR_EXPIRE, "lblcr_expiration" },
- {}
-};
-
static struct trans_ctl_table trans_net_neigh_vars_table[] = {
{ NET_NEIGH_MCAST_SOLICIT, "mcast_solicit" },
{ NET_NEIGH_UCAST_SOLICIT, "ucast_solicit" },
{ NET_IPV4_ROUTE, "route", trans_net_ipv4_route_table },
/* NET_IPV4_FIB_HASH unused */
{ NET_IPV4_NETFILTER, "netfilter", trans_net_ipv4_netfilter_table },
- { NET_IPV4_VS, "vs", trans_net_ipv4_vs_table },
{ NET_IPV4_TCP_TIMESTAMPS, "tcp_timestamps" },
{ NET_IPV4_TCP_WINDOW_SCALING, "tcp_window_scaling" },
{}
};
-static struct trans_ctl_table trans_appldata_table[] = {
- { CTL_APPLDATA_TIMER, "timer" },
- { CTL_APPLDATA_INTERVAL, "interval" },
- { CTL_APPLDATA_OS, "os" },
- { CTL_APPLDATA_NET_SUM, "net_sum" },
- { CTL_APPLDATA_MEM, "mem" },
- {}
-
-};
-
static struct trans_ctl_table trans_s390dbf_table[] = {
{ 5678 /* CTL_S390DBF_STOPPABLE */, "debug_stoppable" },
{ 5679 /* CTL_S390DBF_ACTIVE */, "debug_active" },
{ CTL_ABI, "abi" },
/* CTL_CPU not used */
{ CTL_ARLAN, "arlan", trans_arlan_table },
- { CTL_APPLDATA, "appldata", trans_appldata_table },
{ CTL_S390DBF, "s390dbf", trans_s390dbf_table },
{ CTL_SUNRPC, "sunrpc", trans_sunrpc_table },
{ CTL_PM, "pm", trans_pm_table },
/* Now we validate the data before disabling interrupts */
- if ((txc->modes & ADJ_OFFSET_SINGLESHOT) == ADJ_OFFSET_SINGLESHOT)
+ if ((txc->modes & ADJ_OFFSET_SINGLESHOT) == ADJ_OFFSET_SINGLESHOT) {
/* singleshot must not be used with any other mode bits */
- if (txc->modes != ADJ_OFFSET_SINGLESHOT)
+ if (txc->modes != ADJ_OFFSET_SINGLESHOT &&
+ txc->modes != ADJ_OFFSET_SS_READ)
return -EINVAL;
+ }
if (txc->modes != ADJ_OFFSET_SINGLESHOT && (txc->modes & ADJ_OFFSET))
/* adjustment Offset limited to +- .512 seconds */
leave: if ((time_status & (STA_UNSYNC|STA_CLOCKERR)) != 0)
result = TIME_ERROR;
- if ((txc->modes & ADJ_OFFSET_SINGLESHOT) == ADJ_OFFSET_SINGLESHOT)
+ if ((txc->modes == ADJ_OFFSET_SINGLESHOT) ||
+ (txc->modes == ADJ_OFFSET_SS_READ))
txc->offset = save_adjust;
else
txc->offset = ((long)shift_right(time_offset, SHIFT_UPDATE)) *
struct user_struct *new;
new = kmem_cache_alloc(uid_cachep, GFP_KERNEL);
- if (!new)
+ if (!new) {
+ uids_mutex_unlock();
return NULL;
+ }
+
new->uid = uid;
atomic_set(&new->__count, 1);
atomic_set(&new->processes, 0);
if (alloc_uid_keyring(new, current) < 0) {
kmem_cache_free(uid_cachep, new);
+ uids_mutex_unlock();
return NULL;
}
key_put(new->uid_keyring);
key_put(new->session_keyring);
kmem_cache_free(uid_cachep, new);
+ uids_mutex_unlock();
return NULL;
}
config DEBUG_BUGVERBOSE
bool "Verbose BUG() reporting (adds 70K)" if DEBUG_KERNEL && EMBEDDED
depends on BUG
- depends on ARM || AVR32 || M32R || M68K || SPARC32 || SPARC64 || FRV || SUPERH || GENERIC_BUG || BFIN
+ depends on ARM || AVR32 || M32R || M68K || SPARC32 || SPARC64 || FRV || SUPERH || GENERIC_BUG || BLACKFIN
default !EMBEDDED
help
Say Y here to make BUG() panics output the file name and line number
config FRAME_POINTER
bool "Compile the kernel with frame pointers"
- depends on DEBUG_KERNEL && (X86 || CRIS || M68K || M68KNOMMU || FRV || UML || S390 || AVR32 || SUPERH || BFIN)
+ depends on DEBUG_KERNEL && (X86 || CRIS || M68K || M68KNOMMU || FRV || UML || S390 || AVR32 || SUPERH || BLACKFIN)
default y if DEBUG_INFO && UML
help
If you say Y here the resulting kernel image will be slightly larger
if (page_mapped(page)) {
struct address_space *mapping = page_mapping(page);
- if (mapping)
+ if (mapping) {
ret = page_mkclean_file(mapping, page);
- if (page_test_dirty(page)) {
- page_clear_dirty(page);
- ret = 1;
+ if (page_test_dirty(page)) {
+ page_clear_dirty(page);
+ ret = 1;
+ }
}
}
if (datalen != EBT_ALIGN(expected_length)) {
printk(KERN_WARNING
- "ebtables: among: wrong size: %d"
+ "ebtables: among: wrong size: %d "
"against expected %d, rounded to %Zd\n",
datalen, expected_length,
EBT_ALIGN(expected_length));
x->curlft.bytes +=skb->len;
x->curlft.packets++;
- spin_unlock(&x->lock);
-
error:
spin_unlock(&x->lock);
return err;
/*
* Free an skbuff by memory without cleaning the state.
*/
-void kfree_skbmem(struct sk_buff *skb)
+static void kfree_skbmem(struct sk_buff *skb)
{
struct sk_buff *other;
atomic_t *fclone_ref;
- skb_release_data(skb);
switch (skb->fclone) {
case SKB_FCLONE_UNAVAILABLE:
kmem_cache_free(skbuff_head_cache, skb);
}
}
-/**
- * __kfree_skb - private function
- * @skb: buffer
- *
- * Free an sk_buff. Release anything attached to the buffer.
- * Clean the state. This is an internal helper function. Users should
- * always call kfree_skb
- */
-
-void __kfree_skb(struct sk_buff *skb)
+/* Free everything but the sk_buff shell. */
+static void skb_release_all(struct sk_buff *skb)
{
dst_release(skb->dst);
#ifdef CONFIG_XFRM
skb->tc_verd = 0;
#endif
#endif
+ skb_release_data(skb);
+}
+
+/**
+ * __kfree_skb - private function
+ * @skb: buffer
+ *
+ * Free an sk_buff. Release anything attached to the buffer.
+ * Clean the state. This is an internal helper function. Users should
+ * always call kfree_skb
+ */
+void __kfree_skb(struct sk_buff *skb)
+{
+ skb_release_all(skb);
kfree_skbmem(skb);
}
*/
struct sk_buff *skb_morph(struct sk_buff *dst, struct sk_buff *src)
{
- skb_release_data(dst);
+ skb_release_all(dst);
return __skb_clone(dst, src);
}
EXPORT_SYMBOL_GPL(skb_morph);
}
if (unlikely(interval == 0)) {
- DCCP_WARN("%s(%p), Could not find a win_count interval > 0."
+ DCCP_WARN("%s(%p), Could not find a win_count interval > 0. "
"Defaulting to 1\n", dccp_role(sk), sk);
interval = 1;
}
pos += 8;
if (ccmp_replay_check(pn, key->rx_pn)) {
- if (net_ratelimit()) {
+ if (ieee80211_ratelimit_debug(IEEE80211_DL_DROP)) {
IEEE80211_DEBUG_DROP("CCMP: replay detected: STA=%s "
"previous PN %02x%02x%02x%02x%02x%02x "
"received PN %02x%02x%02x%02x%02x%02x\n",
pos += 8;
if (tkip_replay_check(iv32, iv16, tkey->rx_iv32, tkey->rx_iv16)) {
- if (net_ratelimit()) {
+ if (ieee80211_ratelimit_debug(IEEE80211_DL_DROP)) {
IEEE80211_DEBUG_DROP("TKIP: replay detected: STA=%s"
" previous TSC %08x%04x received TSC "
"%08x%04x\n", print_mac(mac, hdr->addr2),
* it needs to be recalculated for the next packet. */
tkey->rx_phase1_done = 0;
}
- if (net_ratelimit()) {
+ if (ieee80211_ratelimit_debug(IEEE80211_DL_DROP)) {
IEEE80211_DEBUG_DROP("TKIP: ICV error detected: STA="
"%s\n", print_mac(mac, hdr->addr2));
}
#include <net/tcp.h>
#include <net/sock.h>
#include <net/arp.h>
-#if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE)
#include <net/ax25.h>
-#if defined(CONFIG_NETROM) || defined(CONFIG_NETROM_MODULE)
#include <net/netrom.h>
-#endif
-#endif
#if defined(CONFIG_ATM_CLIP) || defined(CONFIG_ATM_CLIP_MODULE)
#include <net/atmclip.h>
struct neigh_table *clip_tbl_hook;
htons(dev_type) != arp->ar_hrd)
goto out;
break;
-#ifdef CONFIG_NET_ETHERNET
case ARPHRD_ETHER:
-#endif
-#ifdef CONFIG_TR
case ARPHRD_IEEE802_TR:
-#endif
-#ifdef CONFIG_FDDI
case ARPHRD_FDDI:
-#endif
-#ifdef CONFIG_NET_FC
case ARPHRD_IEEE802:
-#endif
-#if defined(CONFIG_NET_ETHERNET) || defined(CONFIG_TR) || \
- defined(CONFIG_FDDI) || defined(CONFIG_NET_FC)
/*
* ETHERNET, Token Ring and Fibre Channel (which are IEEE 802
* devices, according to RFC 2625) devices will accept ARP
arp->ar_pro != htons(ETH_P_IP))
goto out;
break;
-#endif
-#if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE)
case ARPHRD_AX25:
if (arp->ar_pro != htons(AX25_P_IP) ||
arp->ar_hrd != htons(ARPHRD_AX25))
goto out;
break;
-#if defined(CONFIG_NETROM) || defined(CONFIG_NETROM_MODULE)
case ARPHRD_NETROM:
if (arp->ar_pro != htons(AX25_P_IP) ||
arp->ar_hrd != htons(ARPHRD_NETROM))
goto out;
break;
-#endif
-#endif
}
/* Understand only these message types */
if (arp->ar_op == htons(ARPOP_REQUEST) &&
inet_addr_type(tip) == RTN_LOCAL &&
!arp_ignore(in_dev,dev,sip,tip))
- arp_send(ARPOP_REPLY,ETH_P_ARP,tip,dev,tip,sha,dev->dev_addr,dev->dev_addr);
+ arp_send(ARPOP_REPLY, ETH_P_ARP, sip, dev, tip, sha,
+ dev->dev_addr, sha);
goto out;
}
verdict = NF_DROP;
if (IP_VS_FWD_METHOD(cp) != 0) {
- IP_VS_ERR("shouldn't reach here, because the box is on the"
+ IP_VS_ERR("shouldn't reach here, because the box is on the "
"half connection in the tun/dr module.\n");
}
static struct ctl_table vs_vars[] = {
{
- .ctl_name = NET_IPV4_VS_AMEMTHRESH,
.procname = "amemthresh",
.data = &sysctl_ip_vs_amemthresh,
.maxlen = sizeof(int),
},
#ifdef CONFIG_IP_VS_DEBUG
{
- .ctl_name = NET_IPV4_VS_DEBUG_LEVEL,
.procname = "debug_level",
.data = &sysctl_ip_vs_debug_level,
.maxlen = sizeof(int),
},
#endif
{
- .ctl_name = NET_IPV4_VS_AMDROPRATE,
.procname = "am_droprate",
.data = &sysctl_ip_vs_am_droprate,
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec,
},
{
- .ctl_name = NET_IPV4_VS_DROP_ENTRY,
.procname = "drop_entry",
.data = &sysctl_ip_vs_drop_entry,
.maxlen = sizeof(int),
.proc_handler = &proc_do_defense_mode,
},
{
- .ctl_name = NET_IPV4_VS_DROP_PACKET,
.procname = "drop_packet",
.data = &sysctl_ip_vs_drop_packet,
.maxlen = sizeof(int),
.proc_handler = &proc_do_defense_mode,
},
{
- .ctl_name = NET_IPV4_VS_SECURE_TCP,
.procname = "secure_tcp",
.data = &sysctl_ip_vs_secure_tcp,
.maxlen = sizeof(int),
},
#if 0
{
- .ctl_name = NET_IPV4_VS_TO_ES,
.procname = "timeout_established",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_ESTABLISHED],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_SS,
.procname = "timeout_synsent",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_SYN_SENT],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_SR,
.procname = "timeout_synrecv",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_SYN_RECV],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_FW,
.procname = "timeout_finwait",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_FIN_WAIT],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_TW,
.procname = "timeout_timewait",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_TIME_WAIT],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_CL,
.procname = "timeout_close",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_CLOSE],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_CW,
.procname = "timeout_closewait",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_CLOSE_WAIT],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_LA,
.procname = "timeout_lastack",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_LAST_ACK],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_LI,
.procname = "timeout_listen",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_LISTEN],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_SA,
.procname = "timeout_synack",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_SYNACK],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_UDP,
.procname = "timeout_udp",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_UDP],
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec_jiffies,
},
{
- .ctl_name = NET_IPV4_VS_TO_ICMP,
.procname = "timeout_icmp",
.data = &vs_timeout_table_dos.timeout[IP_VS_S_ICMP],
.maxlen = sizeof(int),
},
#endif
{
- .ctl_name = NET_IPV4_VS_CACHE_BYPASS,
.procname = "cache_bypass",
.data = &sysctl_ip_vs_cache_bypass,
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec,
},
{
- .ctl_name = NET_IPV4_VS_EXPIRE_NODEST_CONN,
.procname = "expire_nodest_conn",
.data = &sysctl_ip_vs_expire_nodest_conn,
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec,
},
{
- .ctl_name = NET_IPV4_VS_EXPIRE_QUIESCENT_TEMPLATE,
.procname = "expire_quiescent_template",
.data = &sysctl_ip_vs_expire_quiescent_template,
.maxlen = sizeof(int),
.proc_handler = &proc_dointvec,
},
{
- .ctl_name = NET_IPV4_VS_SYNC_THRESHOLD,
.procname = "sync_threshold",
.data = &sysctl_ip_vs_sync_threshold,
.maxlen = sizeof(sysctl_ip_vs_sync_threshold),
.proc_handler = &proc_do_sync_threshold,
},
{
- .ctl_name = NET_IPV4_VS_NAT_ICMP_SEND,
.procname = "nat_icmp_send",
.data = &sysctl_ip_vs_nat_icmp_send,
.maxlen = sizeof(int),
static ctl_table vs_table[] = {
{
- .ctl_name = NET_IPV4_VS,
.procname = "vs",
.mode = 0555,
.child = vs_vars
static ctl_table vs_vars_table[] = {
{
- .ctl_name = NET_IPV4_VS_LBLC_EXPIRE,
.procname = "lblc_expiration",
.data = &sysctl_ip_vs_lblc_expiration,
.maxlen = sizeof(int),
static ctl_table vs_table[] = {
{
- .ctl_name = NET_IPV4_VS,
.procname = "vs",
.mode = 0555,
.child = vs_vars_table
static ctl_table vs_vars_table[] = {
{
- .ctl_name = NET_IPV4_VS_LBLCR_EXPIRE,
.procname = "lblcr_expiration",
.data = &sysctl_ip_vs_lblcr_expiration,
.maxlen = sizeof(int),
static ctl_table vs_table[] = {
{
- .ctl_name = NET_IPV4_VS,
.procname = "vs",
.mode = 0555,
.child = vs_vars_table
/*
* register an ipvs protocol
*/
-static int register_ip_vs_protocol(struct ip_vs_protocol *pp)
+static int __used register_ip_vs_protocol(struct ip_vs_protocol *pp)
{
unsigned hash = IP_VS_PROTO_HASH(pp->protocol);
if (skb->len < sizeof(struct iphdr) ||
ip_hdrlen(skb) < sizeof(struct iphdr)) {
if (net_ratelimit())
- printk("iptable_raw: ignoring short SOCK_RAW"
+ printk("iptable_raw: ignoring short SOCK_RAW "
"packet.\n");
return NF_ACCEPT;
}
struct nf_conn_nat *new_nat = nf_ct_ext_find(conntrack, NF_CT_EXT_NAT);
struct nf_conn_nat *old_nat = (struct nf_conn_nat *)old;
struct nf_conn *ct = old_nat->ct;
- unsigned int srchash;
- if (!(ct->status & IPS_NAT_DONE_MASK))
+ if (!ct || !(ct->status & IPS_NAT_DONE_MASK))
return;
- srchash = hash_by_src(&ct->tuplehash[IP_CT_DIR_ORIGINAL].tuple);
-
write_lock_bh(&nf_nat_lock);
hlist_replace_rcu(&old_nat->bysource, &new_nat->bysource);
new_nat->ct = ct;
offset /= sizeof(u32);
if (length > 0) {
- u32 *src = ((u32 *) IP_RT_ACCT_CPU(0)) + offset;
u32 *dst = (u32 *) buffer;
- /* Copy first cpu. */
*start = buffer;
- memcpy(dst, src, length);
+ memset(dst, 0, length);
- /* Add the other cpus in, one int at a time */
for_each_possible_cpu(i) {
unsigned int j;
-
- src = ((u32 *) IP_RT_ACCT_CPU(i)) + offset;
+ u32 *src = ((u32 *) IP_RT_ACCT_CPU(i)) + offset;
for (j = 0; j < length/4; j++)
dst[j] += src[j];
tcp_get_default_congestion_control(val);
ret = sysctl_string(&tbl, name, nlen, oldval, oldlenp, newval, newlen);
- if (ret == 0 && newval && newlen)
+ if (ret == 1 && newval && newlen)
ret = tcp_set_default_congestion_control(val);
return ret;
}
sizeof(*keys) * md5sig->entries4);
/* Free old key list, and reference new one */
- if (md5sig->keys4)
- kfree(md5sig->keys4);
+ kfree(md5sig->keys4);
md5sig->keys4 = keys;
md5sig->alloced4++;
}
tp->md5sig_info->alloced4 = 0;
} else if (tp->md5sig_info->entries4 != i) {
/* Need to do some manipulation */
- memcpy(&tp->md5sig_info->keys4[i],
- &tp->md5sig_info->keys4[i+1],
- (tp->md5sig_info->entries4 - i) *
- sizeof(struct tcp4_md5sig_key));
+ memmove(&tp->md5sig_info->keys4[i],
+ &tp->md5sig_info->keys4[i+1],
+ (tp->md5sig_info->entries4 - i) *
+ sizeof(struct tcp4_md5sig_key));
}
tcp_free_md5sig_pool();
return 0;
struct sk_buff *skb, *nskb, *next;
int len;
int probe_size;
+ int size_needed;
unsigned int pif;
int copy;
int mss_now;
/* Very simple search strategy: just double the MSS. */
mss_now = tcp_current_mss(sk, 0);
probe_size = 2*tp->mss_cache;
+ size_needed = probe_size + (tp->reordering + 1) * tp->mss_cache;
if (probe_size > tcp_mtu_to_mss(sk, icsk->icsk_mtup.search_high)) {
/* TODO: set timer for probe_converge_event */
return -1;
}
/* Have enough data in the send queue to probe? */
- len = 0;
- if ((skb = tcp_send_head(sk)) == NULL)
- return -1;
- while ((len += skb->len) < probe_size && !tcp_skb_is_last(sk, skb))
- skb = tcp_write_queue_next(sk, skb);
- if (len < probe_size)
+ if (tp->write_seq - tp->snd_nxt < size_needed)
return -1;
- /* Receive window check. */
- if (after(TCP_SKB_CB(skb)->seq + probe_size, tp->snd_una + tp->snd_wnd)) {
- if (tp->snd_wnd < probe_size)
- return -1;
- else
- return 0;
- }
+ if (tp->snd_wnd < size_needed)
+ return -1;
+ if (after(tp->snd_nxt + size_needed, tp->snd_una + tp->snd_wnd))
+ return 0;
/* Do we need to wait to drain cwnd? */
pif = tcp_packets_in_flight(tp);
skb = tcp_send_head(sk);
tcp_insert_write_queue_before(nskb, skb, sk);
- tcp_advance_send_head(sk, skb);
TCP_SKB_CB(nskb)->seq = TCP_SKB_CB(skb)->seq;
TCP_SKB_CB(nskb)->end_seq = TCP_SKB_CB(skb)->seq + probe_size;
if (unlikely(score.addr_type == IPV6_ADDR_ANY ||
score.addr_type & IPV6_ADDR_MULTICAST)) {
LIMIT_NETDEBUG(KERN_DEBUG
- "ADDRCONF: unspecified / multicast address"
+ "ADDRCONF: unspecified / multicast address "
"assigned as unicast address on %s",
dev->name);
continue;
}
sk->sk_route_caps &= ~NETIF_F_GSO_MASK;
}
- tcp_alloc_md5sig_pool();
+ if (tcp_alloc_md5sig_pool() == NULL) {
+ kfree(newkey);
+ return -ENOMEM;
+ }
if (tp->md5sig_info->alloced6 == tp->md5sig_info->entries6) {
keys = kmalloc((sizeof (tp->md5sig_info->keys6[0]) *
(tp->md5sig_info->entries6 + 1)), GFP_ATOMIC);
kfree(tp->md5sig_info->keys6);
tp->md5sig_info->keys6 = NULL;
tp->md5sig_info->alloced6 = 0;
-
- tcp_free_md5sig_pool();
-
- return 0;
} else {
/* shrink the database */
if (tp->md5sig_info->entries6 != i)
(tp->md5sig_info->entries6 - i)
* sizeof (tp->md5sig_info->keys6[0]));
}
+ tcp_free_md5sig_pool();
+ return 0;
}
}
return -ENOENT;
opcode = fp[0];
if (~opcode & 0x80) {
- IRDA_WARNING("%s: IrIAS multiframe commands or results"
+ IRDA_WARNING("%s: IrIAS multiframe commands or results "
"is not implemented yet!\n", __FUNCTION__);
return;
}
*/
void irlan_eth_send_gratuitous_arp(struct net_device *dev)
{
+#ifdef CONFIG_INET
struct in_device *in_dev;
/*
* is useful if we have changed access points on the same
* subnet.
*/
-#ifdef CONFIG_INET
IRDA_DEBUG(4, "IrLAN: Sending gratuitous ARP\n");
rcu_read_lock();
in_dev = __in_dev_get_rcu(dev);
struct iucv_irq_data data;
};
-static struct iucv_irq_data *iucv_irq_data;
+static struct iucv_irq_data *iucv_irq_data[NR_CPUS];
static cpumask_t iucv_buffer_cpumask = CPU_MASK_NONE;
static cpumask_t iucv_irq_cpumask = CPU_MASK_NONE;
/*
* Anchor for per-cpu IUCV command parameter block.
*/
-static union iucv_param *iucv_param;
+static union iucv_param *iucv_param[NR_CPUS];
/**
* iucv_call_b2f0
* 0x10 - Flag to allow priority message completion interrupts
* 0x08 - Flag to allow IUCV control interrupts
*/
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
parm->set_mask.ipmask = 0xf8;
iucv_call_b2f0(IUCV_SETMASK, parm);
union iucv_param *parm;
/* Disable all iucv interrupts. */
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
iucv_call_b2f0(IUCV_SETMASK, parm);
return;
/* Declare interrupt buffer. */
- parm = percpu_ptr(iucv_param, cpu);
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
- parm->db.ipbfadr1 = virt_to_phys(percpu_ptr(iucv_irq_data, cpu));
+ parm->db.ipbfadr1 = virt_to_phys(iucv_irq_data[cpu]);
rc = iucv_call_b2f0(IUCV_DECLARE_BUFFER, parm);
if (rc) {
char *err = "Unknown";
iucv_block_cpu(NULL);
/* Retrieve interrupt buffer. */
- parm = percpu_ptr(iucv_param, cpu);
+ parm = iucv_param[cpu];
iucv_call_b2f0(IUCV_RETRIEVE_BUFFER, parm);
/* Clear indication that an iucv buffer exists for this cpu. */
switch (action) {
case CPU_UP_PREPARE:
case CPU_UP_PREPARE_FROZEN:
- if (!percpu_populate(iucv_irq_data,
- sizeof(struct iucv_irq_data),
- GFP_KERNEL|GFP_DMA, cpu))
+ iucv_irq_data[cpu] = kmalloc_node(sizeof(struct iucv_irq_data),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_irq_data[cpu])
return NOTIFY_BAD;
- if (!percpu_populate(iucv_param, sizeof(union iucv_param),
- GFP_KERNEL|GFP_DMA, cpu)) {
- percpu_depopulate(iucv_irq_data, cpu);
+ iucv_param[cpu] = kmalloc_node(sizeof(union iucv_param),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_param[cpu])
return NOTIFY_BAD;
- }
break;
case CPU_UP_CANCELED:
case CPU_UP_CANCELED_FROZEN:
case CPU_DEAD:
case CPU_DEAD_FROZEN:
- percpu_depopulate(iucv_param, cpu);
- percpu_depopulate(iucv_irq_data, cpu);
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
break;
case CPU_ONLINE:
case CPU_ONLINE_FROZEN:
{
union iucv_param *parm;
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
local_bh_disable();
/* Prepare parameter block. */
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->ctrl.ippathid = path->pathid;
parm->ctrl.ipmsglim = path->msglim;
BUG_ON(in_atomic());
spin_lock_bh(&iucv_table_lock);
iucv_cleanup_queue();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->ctrl.ipmsglim = path->msglim;
parm->ctrl.ipflags1 = path->flags;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->purge.ippathid = path->pathid;
parm->purge.ipmsgid = msg->id;
}
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->db.ipbfadr1 = (u32)(addr_t) buffer;
parm->db.ipbfln1f = (u32) size;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->db.ippathid = path->pathid;
parm->db.ipmsgid = msg->id;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
parm->dpl.ippathid = path->pathid;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
/* Message of 8 bytes can be placed into the parameter list. */
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
parm->dpl.ippathid = path->pathid;
struct iucv_irq_data *p;
struct iucv_irq_list *work;
- p = percpu_ptr(iucv_irq_data, smp_processor_id());
+ p = iucv_irq_data[smp_processor_id()];
if (p->ippathid >= iucv_max_pathid) {
printk(KERN_WARNING "iucv_do_int: Got interrupt with "
"pathid %d > max_connections (%ld)\n",
static int __init iucv_init(void)
{
int rc;
+ int cpu;
if (!MACHINE_IS_VM) {
rc = -EPROTONOSUPPORT;
rc = PTR_ERR(iucv_root);
goto out_bus;
}
- /* Note: GFP_DMA used to get memory below 2G */
- iucv_irq_data = percpu_alloc(sizeof(struct iucv_irq_data),
- GFP_KERNEL|GFP_DMA);
- if (!iucv_irq_data) {
- rc = -ENOMEM;
- goto out_root;
- }
- /* Allocate parameter blocks. */
- iucv_param = percpu_alloc(sizeof(union iucv_param),
- GFP_KERNEL|GFP_DMA);
- if (!iucv_param) {
- rc = -ENOMEM;
- goto out_extint;
+
+ for_each_online_cpu(cpu) {
+ /* Note: GFP_DMA used to get memory below 2G */
+ iucv_irq_data[cpu] = kmalloc_node(sizeof(struct iucv_irq_data),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_irq_data[cpu]) {
+ rc = -ENOMEM;
+ goto out_free;
+ }
+
+ /* Allocate parameter blocks. */
+ iucv_param[cpu] = kmalloc_node(sizeof(union iucv_param),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_param[cpu]) {
+ rc = -ENOMEM;
+ goto out_free;
+ }
}
register_hotcpu_notifier(&iucv_cpu_notifier);
ASCEBC(iucv_error_no_listener, 16);
iucv_available = 1;
return 0;
-out_extint:
- percpu_free(iucv_irq_data);
-out_root:
+out_free:
+ for_each_possible_cpu(cpu) {
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
+ }
s390_root_dev_unregister(iucv_root);
out_bus:
bus_unregister(&iucv_bus);
static void __exit iucv_exit(void)
{
struct iucv_irq_list *p, *n;
+ int cpu;
spin_lock_irq(&iucv_queue_lock);
list_for_each_entry_safe(p, n, &iucv_task_queue, list)
kfree(p);
spin_unlock_irq(&iucv_queue_lock);
unregister_hotcpu_notifier(&iucv_cpu_notifier);
- percpu_free(iucv_param);
- percpu_free(iucv_irq_data);
+ for_each_possible_cpu(cpu) {
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
+ }
s390_root_dev_unregister(iucv_root);
bus_unregister(&iucv_bus);
unregister_external_interrupt(0x4000, iucv_external_interrupt);
{
struct sk_buff *skb;
- spin_lock_bh(&x->lock);
skb = __pfkey_xfrm_state2msg(x, 1, 3);
- spin_unlock_bh(&x->lock);
return skb;
}
out_hdr = (struct sadb_msg *) out_skb->data;
out_hdr->sadb_msg_version = hdr->sadb_msg_version;
- out_hdr->sadb_msg_type = SADB_DUMP;
+ out_hdr->sadb_msg_type = SADB_GET;
out_hdr->sadb_msg_satype = pfkey_proto2satype(proto);
out_hdr->sadb_msg_errno = 0;
out_hdr->sadb_msg_reserved = 0;
tasklet_enable(&local->tasklet);
}
+ /*
+ * set_multicast_list will be invoked by the networking core
+ * which will check whether any increments here were done in
+ * error and sync them down to the hardware as filter flags.
+ */
+ if (sdata->flags & IEEE80211_SDATA_ALLMULTI)
+ atomic_inc(&local->iff_allmultis);
+
+ if (sdata->flags & IEEE80211_SDATA_PROMISC)
+ atomic_inc(&local->iff_promiscs);
+
local->open_count++;
netif_start_queue(dev);
netif_stop_queue(dev);
+ /*
+ * Don't count this interface for promisc/allmulti while it
+ * is down. dev_mc_unsync() will invoke set_multicast_list
+ * on the master interface which will sync these down to the
+ * hardware as filter flags.
+ */
+ if (sdata->flags & IEEE80211_SDATA_ALLMULTI)
+ atomic_dec(&local->iff_allmultis);
+
+ if (sdata->flags & IEEE80211_SDATA_PROMISC)
+ atomic_dec(&local->iff_promiscs);
+
dev_mc_unsync(local->mdev, dev);
/* down all dependent devices, that is VLANs */
allmulti = !!(dev->flags & IFF_ALLMULTI);
promisc = !!(dev->flags & IFF_PROMISC);
- sdata_allmulti = sdata->flags & IEEE80211_SDATA_ALLMULTI;
- sdata_promisc = sdata->flags & IEEE80211_SDATA_PROMISC;
+ sdata_allmulti = !!(sdata->flags & IEEE80211_SDATA_ALLMULTI);
+ sdata_promisc = !!(sdata->flags & IEEE80211_SDATA_PROMISC);
if (allmulti != sdata_allmulti) {
if (dev->flags & IFF_ALLMULTI)
local->sta_scanning = 0;
if (ieee80211_hw_config(local))
- printk(KERN_DEBUG "%s: failed to restore operational"
+ printk(KERN_DEBUG "%s: failed to restore operational "
"channel after scan\n", dev->name);
/* Check if the timestamp looks valid. */
if (time_after(hbinfo->sent_at, jiffies) ||
time_after(jiffies, hbinfo->sent_at + max_interval)) {
- SCTP_DEBUG_PRINTK("%s: HEARTBEAT ACK with invalid timestamp"
+ SCTP_DEBUG_PRINTK("%s: HEARTBEAT ACK with invalid timestamp "
"received for transport: %p\n",
__FUNCTION__, link);
return SCTP_DISPOSITION_DISCARD;
p = gss_fill_context(p, end, ctx, gss_msg->auth->mech);
if (IS_ERR(p)) {
err = PTR_ERR(p);
- gss_msg->msg.errno = (err == -EACCES) ? -EACCES : -EAGAIN;
+ gss_msg->msg.errno = (err == -EAGAIN) ? -EAGAIN : -EACCES;
goto err_release_msg;
}
gss_msg->ctx = gss_get_ctx(ctx);
if (maj_stat == GSS_S_CONTEXT_EXPIRED)
clear_bit(RPCAUTH_CRED_UPTODATE, &cred->cr_flags);
if (maj_stat) {
- dprintk("RPC: %5u gss_validate: gss_verify_mic returned"
+ dprintk("RPC: %5u gss_validate: gss_verify_mic returned "
"error 0x%08x\n", task->tk_pid, maj_stat);
goto out_bad;
}
p = simple_get_bytes(p, end, &tmp, sizeof(tmp));
if (IS_ERR(p))
goto out_err_free_ctx;
- if (tmp != SGN_ALG_DES_MAC_MD5)
+ if (tmp != SGN_ALG_DES_MAC_MD5) {
+ p = ERR_PTR(-ENOSYS);
goto out_err_free_ctx;
+ }
p = simple_get_bytes(p, end, &tmp, sizeof(tmp));
if (IS_ERR(p))
goto out_err_free_ctx;
- if (tmp != SEAL_ALG_DES)
+ if (tmp != SEAL_ALG_DES) {
+ p = ERR_PTR(-ENOSYS);
goto out_err_free_ctx;
+ }
p = simple_get_bytes(p, end, &ctx->endtime, sizeof(ctx->endtime));
if (IS_ERR(p))
goto out_err_free_ctx;
u32 seq_send;
dprintk("RPC: gss_krb5_seal\n");
+ BUG_ON(ctx == NULL);
now = get_seconds();
mask = POLLOUT | POLLWRNORM;
if (rpci->ops == NULL)
mask |= POLLERR | POLLHUP;
- if (!list_empty(&rpci->pipe))
+ if (filp->private_data || !list_empty(&rpci->pipe))
mask |= POLLIN | POLLRDNORM;
return mask;
}
static void xprt_connect_status(struct rpc_task *task);
static int __xprt_get_cong(struct rpc_xprt *, struct rpc_task *);
-static spinlock_t xprt_list_lock = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(xprt_list_lock);
static LIST_HEAD(xprt_list);
/*
static ctl_table xr_tunables_table[] = {
{
- .ctl_name = CTL_SLOTTABLE_RDMA,
+ .ctl_name = CTL_UNNUMBERED,
.procname = "rdma_slot_table_entries",
.data = &xprt_rdma_slot_table_entries,
.maxlen = sizeof(unsigned int),
.extra2 = &max_slot_table_size
},
{
- .ctl_name = CTL_RDMA_MAXINLINEREAD,
+ .ctl_name = CTL_UNNUMBERED,
.procname = "rdma_max_inline_read",
.data = &xprt_rdma_max_inline_read,
.maxlen = sizeof(unsigned int),
.strategy = &sysctl_intvec,
},
{
- .ctl_name = CTL_RDMA_MAXINLINEWRITE,
+ .ctl_name = CTL_UNNUMBERED,
.procname = "rdma_max_inline_write",
.data = &xprt_rdma_max_inline_write,
.maxlen = sizeof(unsigned int),
.strategy = &sysctl_intvec,
},
{
- .ctl_name = CTL_RDMA_WRITEPADDING,
+ .ctl_name = CTL_UNNUMBERED,
.procname = "rdma_inline_write_padding",
.data = &xprt_rdma_inline_write_padding,
.maxlen = sizeof(unsigned int),
.extra2 = &max_padding,
},
{
- .ctl_name = CTL_RDMA_MEMREG,
+ .ctl_name = CTL_UNNUMBERED,
.procname = "rdma_memreg_strategy",
.data = &xprt_rdma_memreg_strategy,
.maxlen = sizeof(unsigned int),
* @args: rpc transport creation arguments
*
*/
-struct rpc_xprt *xs_setup_udp(struct xprt_create *args)
+static struct rpc_xprt *xs_setup_udp(struct xprt_create *args)
{
struct sockaddr *addr = args->dstaddr;
struct rpc_xprt *xprt;
* @args: rpc transport creation arguments
*
*/
-struct rpc_xprt *xs_setup_tcp(struct xprt_create *args)
+static struct rpc_xprt *xs_setup_tcp(struct xprt_create *args)
{
struct sockaddr *addr = args->dstaddr;
struct rpc_xprt *xprt;
rtnl_lock();
ret = wireless_process_ioctl(net, ifr, cmd);
rtnl_unlock();
- if (IW_IS_GET(cmd) && copy_to_user(arg, ifr, sizeof(struct ifreq)))
+ if (IW_IS_GET(cmd) && copy_to_user(arg, ifr, sizeof(struct iwreq)))
return -EFAULT;
return ret;
}
* The xfrm_state_alloc call gives a reference, and that
* is what we are dropping here.
*/
- __xfrm_state_put(x);
+ xfrm_state_put(x);
err = 0;
}
struct xfrm_usersa_info *p,
struct sk_buff *skb)
{
- spin_lock_bh(&x->lock);
copy_to_user_state(x, p);
if (x->coaddr)
if (x->lastused)
NLA_PUT_U64(skb, XFRMA_LASTUSED, x->lastused);
- spin_unlock_bh(&x->lock);
if (x->aalg)
NLA_PUT(skb, XFRMA_ALG_AUTH, alg_len(x->aalg), x->aalg);
static void uart_interrupt_tx(struct snd_mpu401 *mpu)
{
+ unsigned long flags;
+
if (test_bit(MPU401_MODE_BIT_OUTPUT, &mpu->mode) &&
test_bit(MPU401_MODE_BIT_OUTPUT_TRIGGER, &mpu->mode)) {
- spin_lock(&mpu->output_lock);
+ spin_lock_irqsave(&mpu->output_lock, flags);
snd_mpu401_uart_output_write(mpu);
- spin_unlock(&mpu->output_lock);
+ spin_unlock_irqrestore(&mpu->output_lock, flags);
}
}
static void _snd_mpu401_uart_interrupt(struct snd_mpu401 *mpu)
{
+ unsigned long flags;
+
if (mpu->info_flags & MPU401_INFO_INPUT) {
- spin_lock(&mpu->input_lock);
+ spin_lock_irqsave(&mpu->input_lock, flags);
if (test_bit(MPU401_MODE_BIT_INPUT, &mpu->mode))
snd_mpu401_uart_input_read(mpu);
else
snd_mpu401_uart_clear_rx(mpu);
- spin_unlock(&mpu->input_lock);
+ spin_unlock_irqrestore(&mpu->input_lock, flags);
}
if (! (mpu->info_flags & MPU401_INFO_TX_IRQ))
/* ok. for better Tx performance try do some output
parport_release(pardev);
parport_unregister_device(pardev);
- return res;
+ return res ? -EIO : 0;
}
static void __devinit snd_portman_attach(struct parport *p)
{
struct snd_ca0106 *emu = snd_kcontrol_chip(kcontrol);
- ucontrol->value.enumerated.item[0] = emu->spdif_enable;
+ ucontrol->value.integer.value[0] = emu->spdif_enable;
return 0;
}
int change = 0;
u32 mask;
- val = ucontrol->value.enumerated.item[0] ;
+ val = !!ucontrol->value.integer.value[0];
change = (emu->spdif_enable != val);
if (change) {
emu->spdif_enable = val;
- if (val == 1) {
+ if (val) {
/* Digital */
snd_ca0106_ptr_write(emu, SPDIF_SELECT1, 0, 0xf);
snd_ca0106_ptr_write(emu, SPDIF_SELECT2, 0, 0x0b000000);
u32 source;
val = ucontrol->value.enumerated.item[0] ;
+ if (val >= 6)
+ return -EINVAL;
change = (emu->capture_source != val);
if (change) {
emu->capture_source = val;
* for the particular source.
*/
source_id = ucontrol->value.enumerated.item[0] ;
+ if (source_id >= 4)
+ return -EINVAL;
change = (emu->i2c_capture_source != source_id);
if (change) {
snd_ca0106_i2c_write(emu, ADC_MUX, 0); /* Mute input */
u32 tmp;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 1)
+ return -EINVAL;
change = (emu->capture_mic_line_in != val);
if (change) {
emu->capture_mic_line_in = val;
ogain = emu->i2c_capture_volume[source_id][0]; /* Left */
ngain = ucontrol->value.integer.value[0];
if (ngain > 0xff)
- return 0;
+ return -EINVAL;
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_ca0106_i2c_write(emu, ADC_ATTEN_ADCL, ((ngain) & 0xff) );
ogain = emu->i2c_capture_volume[source_id][1]; /* Right */
ngain = ucontrol->value.integer.value[1];
if (ngain > 0xff)
- return 0;
+ return -EINVAL;
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_ca0106_i2c_write(emu, ADC_ATTEN_ADCR, ((ngain) & 0xff));
}
ret = snd_ca0106_spi_write(emu, emu->spi_dac_reg[reg]);
- return ret ? -1 : 1;
+ return ret ? -EINVAL : 1;
}
#define CA_VOLUME(xname,chid,reg) \
snd_info_set_text_ops(entry, emu, snd_ca0106_proc_reg_read1);
entry->c.text.write = snd_ca0106_proc_reg_write;
entry->mode |= S_IWUSR;
-// entry->private_data = emu;
}
if(! snd_card_proc_new(emu->card, "ca0106_i2c", &entry)) {
- snd_info_set_text_ops(entry, emu, snd_ca0106_proc_i2c_write);
entry->c.text.write = snd_ca0106_proc_i2c_write;
+ entry->private_data = emu;
entry->mode |= S_IWUSR;
-// entry->private_data = emu;
}
if(! snd_card_proc_new(emu->card, "ca0106_regs2", &entry))
snd_info_set_text_ops(entry, emu, snd_ca0106_proc_reg_read2);
#define CM_MMODE_MASK 0x00000E00 /* model DAA interface mode */
#define CM_SPDIF_SELECT2 0x00000100 /* for model > 039 ? */
#define CM_ENCENTER 0x00000080
-#define CM_FLINKON 0x00000080 /* force modem link detection on, model 037 */
+#define CM_FLINKON 0x00000040 /* force modem link detection on, model 037 */
#define CM_MUTECH1 0x00000040 /* mute PCI ch1 to DAC */
-#define CM_FLINKOFF 0x00000040 /* force modem link detection off, model 037 */
-#define CM_UNKNOWN_18_5 0x00000020 /* ? */
+#define CM_FLINKOFF 0x00000020 /* force modem link detection off, model 037 */
#define CM_MIDSMP 0x00000010 /* 1/2 interpolation at front end DAC */
#define CM_UPDDMA_MASK 0x0000000C /* TDMA position update notification */
#define CM_UPDDMA_2048 0x00000000
unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
unsigned long flags;
+ /* Limit: emu->spdif_bits */
+ if (idx >= 3)
+ return -EINVAL;
spin_lock_irqsave(&emu->reg_lock, flags);
ucontrol->value.iec958.status[0] = (emu->spdif_bits[idx] >> 0) & 0xff;
ucontrol->value.iec958.status[1] = (emu->spdif_bits[idx] >> 8) & 0xff;
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int channel;
+ unsigned int channel;
channel = (kcontrol->private_value) & 0xff;
+ /* Limit: emu1010_output_dst, emu->emu1010.output_source */
+ if (channel >= 24)
+ return -EINVAL;
ucontrol->value.enumerated.item[0] = emu->emu1010.output_source[channel];
return 0;
}
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
int change = 0;
unsigned int val;
- int channel;
+ unsigned int channel;
+ val = ucontrol->value.enumerated.item[0];
+ if (val >= 53)
+ return -EINVAL;
channel = (kcontrol->private_value) & 0xff;
- if (emu->emu1010.output_source[channel] != ucontrol->value.enumerated.item[0]) {
- val = emu->emu1010.output_source[channel] = ucontrol->value.enumerated.item[0];
+ /* Limit: emu1010_output_dst, emu->emu1010.output_source */
+ if (channel >= 24)
+ return -EINVAL;
+ if (emu->emu1010.output_source[channel] != val) {
+ emu->emu1010.output_source[channel] = val;
change = 1;
snd_emu1010_fpga_link_dst_src_write(emu,
emu1010_output_dst[channel], emu1010_src_regs[val]);
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int channel;
+ unsigned int channel;
channel = (kcontrol->private_value) & 0xff;
+ /* Limit: emu1010_input_dst, emu->emu1010.input_source */
+ if (channel >= 22)
+ return -EINVAL;
ucontrol->value.enumerated.item[0] = emu->emu1010.input_source[channel];
return 0;
}
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
int change = 0;
unsigned int val;
- int channel;
+ unsigned int channel;
+ val = ucontrol->value.enumerated.item[0];
+ if (val >= 53)
+ return -EINVAL;
channel = (kcontrol->private_value) & 0xff;
- if (emu->emu1010.input_source[channel] != ucontrol->value.enumerated.item[0]) {
- val = emu->emu1010.input_source[channel] = ucontrol->value.enumerated.item[0];
+ /* Limit: emu1010_input_dst, emu->emu1010.input_source */
+ if (channel >= 22)
+ return -EINVAL;
+ if (emu->emu1010.input_source[channel] != val) {
+ emu->emu1010.input_source[channel] = val;
change = 1;
snd_emu1010_fpga_link_dst_src_write(emu,
emu1010_input_dst[channel], emu1010_src_regs[val]);
int change = 0;
val = ucontrol->value.enumerated.item[0] ;
+ /* Limit: uinfo->value.enumerated.items = 4; */
+ if (val >= 4)
+ return -EINVAL;
change = (emu->emu1010.internal_clock != val);
if (change) {
emu->emu1010.internal_clock = val;
* update the capture volume from the cached value
* for the particular source.
*/
- source_id = ucontrol->value.enumerated.item[0]; /* Use 2 and 3 */
+ source_id = ucontrol->value.enumerated.item[0];
+ /* Limit: uinfo->value.enumerated.items = 2; */
+ /* emu->i2c_capture_volume */
+ if (source_id >= 2)
+ return -EINVAL;
change = (emu->i2c_capture_source != source_id);
if (change) {
snd_emu10k1_i2c_write(emu, ADC_MUX, 0); /* Mute input */
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int source_id;
+ unsigned int source_id;
source_id = kcontrol->private_value;
+ /* Limit: emu->i2c_capture_volume */
+ /* capture_source: uinfo->value.enumerated.items = 2 */
+ if (source_id >= 2)
+ return -EINVAL;
ucontrol->value.integer.value[0] = emu->i2c_capture_volume[source_id][0];
ucontrol->value.integer.value[1] = emu->i2c_capture_volume[source_id][1];
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
unsigned int ogain;
unsigned int ngain;
- int source_id;
+ unsigned int source_id;
int change = 0;
source_id = kcontrol->private_value;
+ /* Limit: emu->i2c_capture_volume */
+ /* capture_source: uinfo->value.enumerated.items = 2 */
+ if (source_id >= 2)
+ return -EINVAL;
ogain = emu->i2c_capture_volume[source_id][0]; /* Left */
ngain = ucontrol->value.integer.value[0];
if (ngain > 0xff)
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCL, ((ngain) & 0xff) );
- emu->i2c_capture_volume[source_id][0] = ucontrol->value.integer.value[0];
+ emu->i2c_capture_volume[source_id][0] = ngain;
change = 1;
}
ogain = emu->i2c_capture_volume[source_id][1]; /* Right */
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCR, ((ngain) & 0xff));
- emu->i2c_capture_volume[source_id][1] = ucontrol->value.integer.value[1];
+ emu->i2c_capture_volume[source_id][1] = ngain;
change = 1;
}
unsigned int val;
unsigned long flags;
+ /* Limit: emu->spdif_bits */
+ if (idx >= 3)
+ return -EINVAL;
val = (ucontrol->value.iec958.status[0] << 0) |
(ucontrol->value.iec958.status[1] << 8) |
(ucontrol->value.iec958.status[2] << 16) |
u32 source;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 7)
+ return -EINVAL;
change = (emu->p16v_capture_source != val);
if (change) {
emu->p16v_capture_source = val;
u32 tmp;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 3)
+ return -EINVAL;
change = (emu->p16v_capture_channel != val);
if (change) {
emu->p16v_capture_channel = val;
nid = codec->start_nid;
for (i = 0; i < codec->num_nodes; i++, nid++) {
- if (get_wcaps(codec, nid) & AC_WCAP_POWER) {
- unsigned int pincap;
- /*
- * don't power down the widget if it controls eapd
- * and EAPD_BTLENABLE is set.
- */
- pincap = snd_hda_param_read(codec, nid, AC_PAR_PIN_CAP);
- if (pincap & AC_PINCAP_EAPD) {
- int eapd = snd_hda_codec_read(codec, nid,
- 0, AC_VERB_GET_EAPD_BTLENABLE, 0);
- eapd &= 0x02;
- if (power_state == AC_PWRST_D3 && eapd)
- continue;
+ unsigned int wcaps = get_wcaps(codec, nid);
+ if (wcaps & AC_WCAP_POWER) {
+ unsigned int wid_type = (wcaps & AC_WCAP_TYPE) >>
+ AC_WCAP_TYPE_SHIFT;
+ if (wid_type == AC_WID_PIN) {
+ unsigned int pincap;
+ /*
+ * don't power down the widget if it controls
+ * eapd and EAPD_BTLENABLE is set.
+ */
+ pincap = snd_hda_param_read(codec, nid,
+ AC_PAR_PIN_CAP);
+ if (pincap & AC_PINCAP_EAPD) {
+ int eapd = snd_hda_codec_read(codec,
+ nid, 0,
+ AC_VERB_GET_EAPD_BTLENABLE, 0);
+ eapd &= 0x02;
+ if (power_state == AC_PWRST_D3 && eapd)
+ continue;
+ }
}
snd_hda_codec_write(codec, nid, 0,
AC_VERB_SET_POWER_STATE,
/* front */
snd_hda_codec_setup_stream(codec, nids[HDA_FRONT], stream_tag,
0, format);
- if (mout->hp_nid && mout->hp_nid != nids[HDA_FRONT])
+ if (!mout->no_share_stream &&
+ mout->hp_nid && mout->hp_nid != nids[HDA_FRONT])
/* headphone out will just decode front left/right (stereo) */
snd_hda_codec_setup_stream(codec, mout->hp_nid, stream_tag,
0, format);
/* extra outputs copied from front */
for (i = 0; i < ARRAY_SIZE(mout->extra_out_nid); i++)
- if (mout->extra_out_nid[i])
+ if (!mout->no_share_stream && mout->extra_out_nid[i])
snd_hda_codec_setup_stream(codec,
mout->extra_out_nid[i],
stream_tag, 0, format);
if (chs >= (i + 1) * 2) /* independent out */
snd_hda_codec_setup_stream(codec, nids[i], stream_tag,
i * 2, format);
- else /* copy front */
+ else if (!mout->no_share_stream) /* copy front */
snd_hda_codec_setup_stream(codec, nids[i], stream_tag,
0, format);
}
hda_nid_t dig_out_nid; /* digital out audio widget */
int max_channels; /* currently supported analog channels */
int dig_out_used; /* current usage of digital out (HDA_DIG_XXX) */
+ int no_share_stream; /* don't share a stream with multiple pins */
};
int snd_hda_multi_out_dig_open(struct hda_codec *codec,
break;
}
+ /* AD1986A has a hardware problem that it can't share a stream
+ * with multiple output pins. The copy of front to surrounds
+ * causes noisy or silent outputs at a certain timing, e.g.
+ * changing the volume.
+ * So, let's disable the shared stream.
+ */
+ spec->multiout.no_share_stream = 1;
+
return 0;
}
unsigned int alt_switch: 1;
unsigned int hp_detect: 1;
unsigned int gpio_mute: 1;
- unsigned int no_vol_knob :1;
unsigned int gpio_mask, gpio_data;
return 1;
}
-static int stac92xx_volknob_info(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_info *uinfo)
-{
- uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
- uinfo->count = 1;
- uinfo->value.integer.min = 0;
- uinfo->value.integer.max = 127;
- return 0;
-}
-
-static int stac92xx_volknob_get(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- ucontrol->value.integer.value[0] = kcontrol->private_value & 0xff;
- return 0;
-}
-
-static int stac92xx_volknob_put(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
- unsigned int val = kcontrol->private_value & 0xff;
-
- if (val == ucontrol->value.integer.value[0])
- return 0;
-
- val = ucontrol->value.integer.value[0];
- kcontrol->private_value &= ~0xff;
- kcontrol->private_value |= val;
-
- snd_hda_codec_write_cache(codec, kcontrol->private_value >> 16, 0,
- AC_VERB_SET_VOLUME_KNOB_CONTROL, val | 0x80);
- return 1;
-}
-
-
static struct hda_verb stac9200_core_init[] = {
/* set dac0mux for dac converter */
{ 0x07, AC_VERB_SET_CONNECT_SEL, 0x00},
.private_value = verb_read | (verb_write << 16), \
}
-#define STAC_VOLKNOB(knob_nid) \
- { \
- .iface = SNDRV_CTL_ELEM_IFACE_MIXER, \
- .name = "Master Playback Volume", \
- .count = 1, \
- .info = stac92xx_volknob_info, \
- .get = stac92xx_volknob_get, \
- .put = stac92xx_volknob_put, \
- .private_value = 127 | (knob_nid << 16), \
- }
-
-
static struct snd_kcontrol_new stac9200_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0xb, 0, HDA_OUTPUT),
HDA_CODEC_MUTE("Master Playback Switch", 0xb, 0, HDA_OUTPUT),
},
STAC_INPUT_SOURCE(2),
STAC_ANALOG_LOOPBACK(0xFE0, 0x7E0),
- STAC_VOLKNOB(0x24),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x1b, 0x0, HDA_INPUT),
HDA_CODEC_MUTE_IDX("Capture Switch", 0x0, 0x1d, 0x0, HDA_OUTPUT),
/* This needs to be generated dynamically based on sequence */
static struct snd_kcontrol_new stac922x_mixer[] = {
STAC_INPUT_SOURCE(2),
- STAC_VOLKNOB(0x16),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x17, 0x0, HDA_INPUT),
HDA_CODEC_MUTE_IDX("Capture Switch", 0x0, 0x17, 0x0, HDA_INPUT),
HDA_CODEC_VOLUME_IDX("Mux Capture Volume", 0x0, 0x12, 0x0, HDA_OUTPUT),
static struct snd_kcontrol_new stac927x_mixer[] = {
STAC_INPUT_SOURCE(3),
- STAC_VOLKNOB(0x24),
STAC_ANALOG_LOOPBACK(0xFEB, 0x7EB),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x18, 0x0, HDA_INPUT),
}
if (spec->multiout.hp_nid) {
const char *pfx;
- if (old_num_dacs == spec->multiout.num_dacs &&
- spec->no_vol_knob)
+ if (old_num_dacs == spec->multiout.num_dacs)
pfx = "Master";
else
pfx = "Headphone";
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac9200_pin_nids);
spec->pin_nids = stac9200_pin_nids;
- spec->no_vol_knob = 1;
spec->board_config = snd_hda_check_board_config(codec, STAC_9200_MODELS,
stac9200_models,
stac9200_cfg_tbl);
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac925x_pin_nids);
spec->pin_nids = stac925x_pin_nids;
- spec->no_vol_knob = 1;
spec->board_config = snd_hda_check_board_config(codec, STAC_925x_MODELS,
stac925x_models,
stac925x_cfg_tbl);
codec->owner = THIS_MODULE;
codec->dai = &cs4270_dai;
codec->num_dai = 1;
- codec->private_data = codec + ALIGN(sizeof(struct snd_soc_codec), 4);
+ codec->private_data = (void *) codec +
+ ALIGN(sizeof(struct snd_soc_codec), 4);
socdev->codec = codec;
#include <asm/hardware.h>
#include <asm/io.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/regs-clock.h>
#include <asm/arch/audio.h>
projects / linux-2.6-omap-h63xx.git / commitdiff