+++ /dev/null
-/*
- *
- * Copyright (c) 1999-2000 Grant Erickson <grant@lcse.umn.edu>
- *
- * Module name: oaknet.c
- *
- * Description:
- * Driver for the National Semiconductor DP83902AV Ethernet controller
- * on-board the IBM PowerPC "Oak" evaluation board. Adapted from the
- * various other 8390 drivers written by Donald Becker and Paul Gortmaker.
- *
- * Additional inspiration from the "tcd8390.c" driver from TiVo, Inc.
- * and "enetLib.c" from IBM.
- *
- */
-
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/delay.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/init.h>
-#include <linux/jiffies.h>
-
-#include <asm/board.h>
-#include <asm/io.h>
-
-#include "8390.h"
-
-
-/* Preprocessor Defines */
-
-#if !defined(TRUE) || TRUE != 1
-#define TRUE 1
-#endif
-
-#if !defined(FALSE) || FALSE != 0
-#define FALSE 0
-#endif
-
-#define OAKNET_START_PG 0x20 /* First page of TX buffer */
-#define OAKNET_STOP_PG 0x40 /* Last pagge +1 of RX ring */
-
-#define OAKNET_WAIT (2 * HZ / 100) /* 20 ms */
-
-/* Experimenting with some fixes for a broken driver... */
-
-#define OAKNET_DISINT
-#define OAKNET_HEADCHECK
-#define OAKNET_RWFIX
-
-
-/* Global Variables */
-
-static const char *name = "National DP83902AV";
-
-static struct net_device *oaknet_devs;
-
-
-/* Function Prototypes */
-
-static int oaknet_open(struct net_device *dev);
-static int oaknet_close(struct net_device *dev);
-
-static void oaknet_reset_8390(struct net_device *dev);
-static void oaknet_get_8390_hdr(struct net_device *dev,
- struct e8390_pkt_hdr *hdr, int ring_page);
-static void oaknet_block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset);
-static void oaknet_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page);
-
-static void oaknet_dma_error(struct net_device *dev, const char *name);
-
-
-/*
- * int oaknet_init()
- *
- * Description:
- * This routine performs all the necessary platform-specific initiali-
- * zation and set-up for the IBM "Oak" evaluation board's National
- * Semiconductor DP83902AV "ST-NIC" Ethernet controller.
- *
- * Input(s):
- * N/A
- *
- * Output(s):
- * N/A
- *
- * Returns:
- * 0 if OK, otherwise system error number on error.
- *
- */
-static int __init oaknet_init(void)
-{
- register int i;
- int reg0, regd;
- int ret = -ENOMEM;
- struct net_device *dev;
-#if 0
- unsigned long ioaddr = OAKNET_IO_BASE;
-#else
- unsigned long ioaddr = ioremap(OAKNET_IO_BASE, OAKNET_IO_SIZE);
-#endif
- bd_t *bip = (bd_t *)__res;
-
- if (!ioaddr)
- return -ENOMEM;
-
- dev = alloc_ei_netdev();
- if (!dev)
- goto out_unmap;
-
- ret = -EBUSY;
- if (!request_region(OAKNET_IO_BASE, OAKNET_IO_SIZE, name))
- goto out_dev;
-
- /* Quick register check to see if the device is really there. */
-
- ret = -ENODEV;
- if ((reg0 = ei_ibp(ioaddr)) == 0xFF)
- goto out_region;
-
- /*
- * That worked. Now a more thorough check, using the multicast
- * address registers, that the device is definitely out there
- * and semi-functional.
- */
-
- ei_obp(E8390_NODMA + E8390_PAGE1 + E8390_STOP, ioaddr + E8390_CMD);
- regd = ei_ibp(ioaddr + 0x0D);
- ei_obp(0xFF, ioaddr + 0x0D);
- ei_obp(E8390_NODMA + E8390_PAGE0, ioaddr + E8390_CMD);
- ei_ibp(ioaddr + EN0_COUNTER0);
-
- /* It's no good. Fix things back up and leave. */
-
- ret = -ENODEV;
- if (ei_ibp(ioaddr + EN0_COUNTER0) != 0) {
- ei_obp(reg0, ioaddr);
- ei_obp(regd, ioaddr + 0x0D);
- goto out_region;
- }
-
- SET_MODULE_OWNER(dev);
-
- /*
- * This controller is on an embedded board, so the base address
- * and interrupt assignments are pre-assigned and unchageable.
- */
-
- dev->base_addr = ioaddr;
- dev->irq = OAKNET_INT;
-
- /*
- * Disable all chip interrupts for now and ACK all pending
- * interrupts.
- */
-
- ei_obp(0x0, ioaddr + EN0_IMR);
- ei_obp(0xFF, ioaddr + EN0_ISR);
-
- /* Attempt to get the interrupt line */
-
- ret = -EAGAIN;
- if (request_irq(dev->irq, ei_interrupt, 0, name, dev)) {
- printk("%s: unable to request interrupt %d.\n",
- name, dev->irq);
- goto out_region;
- }
-
- /* Tell the world about what and where we've found. */
-
- printk("%s: %s at", dev->name, name);
- for (i = 0; i < ETHER_ADDR_LEN; ++i) {
- dev->dev_addr[i] = bip->bi_enetaddr[i];
- printk("%c%.2x", (i ? ':' : ' '), dev->dev_addr[i]);
- }
- printk(", found at %#lx, using IRQ %d.\n", dev->base_addr, dev->irq);
-
- /* Set up some required driver fields and then we're done. */
-
- ei_status.name = name;
- ei_status.word16 = FALSE;
- ei_status.tx_start_page = OAKNET_START_PG;
- ei_status.rx_start_page = OAKNET_START_PG + TX_PAGES;
- ei_status.stop_page = OAKNET_STOP_PG;
-
- ei_status.reset_8390 = &oaknet_reset_8390;
- ei_status.block_input = &oaknet_block_input;
- ei_status.block_output = &oaknet_block_output;
- ei_status.get_8390_hdr = &oaknet_get_8390_hdr;
-
- dev->open = oaknet_open;
- dev->stop = oaknet_close;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = ei_poll;
-#endif
-
- NS8390_init(dev, FALSE);
- ret = register_netdev(dev);
- if (ret)
- goto out_irq;
-
- oaknet_devs = dev;
- return 0;
-
-out_irq;
- free_irq(dev->irq, dev);
-out_region:
- release_region(OAKNET_IO_BASE, OAKNET_IO_SIZE);
-out_dev:
- free_netdev(dev);
-out_unmap:
- iounmap(ioaddr);
- return ret;
-}
-
-/*
- * static int oaknet_open()
- *
- * Description:
- * This routine is a modest wrapper around ei_open, the 8390-generic,
- * driver open routine. This just increments the module usage count
- * and passes along the status from ei_open.
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- *
- * Output(s):
- * *dev - Pointer to the device structure for this driver, potentially
- * modified by ei_open.
- *
- * Returns:
- * 0 if OK, otherwise < 0 on error.
- *
- */
-static int
-oaknet_open(struct net_device *dev)
-{
- int status = ei_open(dev);
- return (status);
-}
-
-/*
- * static int oaknet_close()
- *
- * Description:
- * This routine is a modest wrapper around ei_close, the 8390-generic,
- * driver close routine. This just decrements the module usage count
- * and passes along the status from ei_close.
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- *
- * Output(s):
- * *dev - Pointer to the device structure for this driver, potentially
- * modified by ei_close.
- *
- * Returns:
- * 0 if OK, otherwise < 0 on error.
- *
- */
-static int
-oaknet_close(struct net_device *dev)
-{
- int status = ei_close(dev);
- return (status);
-}
-
-/*
- * static void oaknet_reset_8390()
- *
- * Description:
- * This routine resets the DP83902 chip.
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- *
- * Output(s):
- * N/A
- *
- * Returns:
- * N/A
- *
- */
-static void
-oaknet_reset_8390(struct net_device *dev)
-{
- int base = E8390_BASE;
-
- /*
- * We have no provision of reseting the controller as is done
- * in other drivers, such as "ne.c". However, the following
- * seems to work well enough in the TiVo driver.
- */
-
- printk("Resetting %s...\n", dev->name);
- ei_obp(E8390_STOP | E8390_NODMA | E8390_PAGE0, base + E8390_CMD);
- ei_status.txing = 0;
- ei_status.dmaing = 0;
-}
-
-/*
- * static void oaknet_get_8390_hdr()
- *
- * Description:
- * This routine grabs the 8390-specific header. It's similar to the
- * block input routine, but we don't need to be concerned with ring wrap
- * as the header will be at the start of a page, so we optimize accordingly.
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- * *hdr - Pointer to storage for the 8390-specific packet header.
- * ring_page - ?
- *
- * Output(s):
- * *hdr - Pointer to the 8390-specific packet header for the just-
- * received frame.
- *
- * Returns:
- * N/A
- *
- */
-static void
-oaknet_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
- int ring_page)
-{
- int base = dev->base_addr;
-
- /*
- * This should NOT happen. If it does, it is the LAST thing you'll
- * see.
- */
-
- if (ei_status.dmaing) {
- oaknet_dma_error(dev, "oaknet_get_8390_hdr");
- return;
- }
-
- ei_status.dmaing |= 0x01;
- outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START, base + OAKNET_CMD);
- outb_p(sizeof(struct e8390_pkt_hdr), base + EN0_RCNTLO);
- outb_p(0, base + EN0_RCNTHI);
- outb_p(0, base + EN0_RSARLO); /* On page boundary */
- outb_p(ring_page, base + EN0_RSARHI);
- outb_p(E8390_RREAD + E8390_START, base + OAKNET_CMD);
-
- if (ei_status.word16)
- insw(base + OAKNET_DATA, hdr,
- sizeof(struct e8390_pkt_hdr) >> 1);
- else
- insb(base + OAKNET_DATA, hdr,
- sizeof(struct e8390_pkt_hdr));
-
- /* Byte-swap the packet byte count */
-
- hdr->count = le16_to_cpu(hdr->count);
-
- outb_p(ENISR_RDC, base + EN0_ISR); /* ACK Remote DMA interrupt */
- ei_status.dmaing &= ~0x01;
-}
-
-/*
- * XXX - Document me.
- */
-static void
-oaknet_block_input(struct net_device *dev, int count, struct sk_buff *skb,
- int ring_offset)
-{
- int base = OAKNET_BASE;
- char *buf = skb->data;
-
- /*
- * This should NOT happen. If it does, it is the LAST thing you'll
- * see.
- */
-
- if (ei_status.dmaing) {
- oaknet_dma_error(dev, "oaknet_block_input");
- return;
- }
-
-#ifdef OAKNET_DISINT
- save_flags(flags);
- cli();
-#endif
-
- ei_status.dmaing |= 0x01;
- ei_obp(E8390_NODMA + E8390_PAGE0 + E8390_START, base + E8390_CMD);
- ei_obp(count & 0xff, base + EN0_RCNTLO);
- ei_obp(count >> 8, base + EN0_RCNTHI);
- ei_obp(ring_offset & 0xff, base + EN0_RSARLO);
- ei_obp(ring_offset >> 8, base + EN0_RSARHI);
- ei_obp(E8390_RREAD + E8390_START, base + E8390_CMD);
- if (ei_status.word16) {
- ei_isw(base + E8390_DATA, buf, count >> 1);
- if (count & 0x01) {
- buf[count - 1] = ei_ib(base + E8390_DATA);
-#ifdef OAKNET_HEADCHECK
- bytes++;
-#endif
- }
- } else {
- ei_isb(base + E8390_DATA, buf, count);
- }
-#ifdef OAKNET_HEADCHECK
- /*
- * This was for the ALPHA version only, but enough people have
- * been encountering problems so it is still here. If you see
- * this message you either 1) have a slightly incompatible clone
- * or 2) have noise/speed problems with your bus.
- */
-
- /* DMA termination address check... */
- {
- int addr, tries = 20;
- do {
- /* DON'T check for 'ei_ibp(EN0_ISR) & ENISR_RDC' here
- -- it's broken for Rx on some cards! */
- int high = ei_ibp(base + EN0_RSARHI);
- int low = ei_ibp(base + EN0_RSARLO);
- addr = (high << 8) + low;
- if (((ring_offset + bytes) & 0xff) == low)
- break;
- } while (--tries > 0);
- if (tries <= 0)
- printk("%s: RX transfer address mismatch,"
- "%#4.4x (expected) vs. %#4.4x (actual).\n",
- dev->name, ring_offset + bytes, addr);
- }
-#endif
- ei_obp(ENISR_RDC, base + EN0_ISR); /* ACK Remote DMA interrupt */
- ei_status.dmaing &= ~0x01;
-
-#ifdef OAKNET_DISINT
- restore_flags(flags);
-#endif
-}
-
-/*
- * static void oaknet_block_output()
- *
- * Description:
- * This routine...
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- * count - Number of bytes to be transferred.
- * *buf -
- * start_page -
- *
- * Output(s):
- * N/A
- *
- * Returns:
- * N/A
- *
- */
-static void
-oaknet_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page)
-{
- int base = E8390_BASE;
-#if 0
- int bug;
-#endif
- unsigned long start;
-#ifdef OAKNET_DISINT
- unsigned long flags;
-#endif
-#ifdef OAKNET_HEADCHECK
- int retries = 0;
-#endif
-
- /* Round the count up for word writes. */
-
- if (ei_status.word16 && (count & 0x1))
- count++;
-
- /*
- * This should NOT happen. If it does, it is the LAST thing you'll
- * see.
- */
-
- if (ei_status.dmaing) {
- oaknet_dma_error(dev, "oaknet_block_output");
- return;
- }
-
-#ifdef OAKNET_DISINT
- save_flags(flags);
- cli();
-#endif
-
- ei_status.dmaing |= 0x01;
-
- /* Make sure we are in page 0. */
-
- ei_obp(E8390_PAGE0 + E8390_START + E8390_NODMA, base + E8390_CMD);
-
-#ifdef OAKNET_HEADCHECK
-retry:
-#endif
-
-#if 0
- /*
- * The 83902 documentation states that the processor needs to
- * do a "dummy read" before doing the remote write to work
- * around a chip bug they don't feel like fixing.
- */
-
- bug = 0;
- while (1) {
- unsigned int rdhi;
- unsigned int rdlo;
-
- /* Now the normal output. */
- ei_obp(ENISR_RDC, base + EN0_ISR);
- ei_obp(count & 0xff, base + EN0_RCNTLO);
- ei_obp(count >> 8, base + EN0_RCNTHI);
- ei_obp(0x00, base + EN0_RSARLO);
- ei_obp(start_page, base + EN0_RSARHI);
-
- if (bug++)
- break;
-
- /* Perform the dummy read */
- rdhi = ei_ibp(base + EN0_CRDAHI);
- rdlo = ei_ibp(base + EN0_CRDALO);
- ei_obp(E8390_RREAD + E8390_START, base + E8390_CMD);
-
- while (1) {
- unsigned int nrdhi;
- unsigned int nrdlo;
- nrdhi = ei_ibp(base + EN0_CRDAHI);
- nrdlo = ei_ibp(base + EN0_CRDALO);
- if ((rdhi != nrdhi) || (rdlo != nrdlo))
- break;
- }
- }
-#else
-#ifdef OAKNET_RWFIX
- /*
- * Handle the read-before-write bug the same way as the
- * Crynwr packet driver -- the Nat'l Semi. method doesn't work.
- * Actually this doesn't always work either, but if you have
- * problems with your 83902 this is better than nothing!
- */
-
- ei_obp(0x42, base + EN0_RCNTLO);
- ei_obp(0x00, base + EN0_RCNTHI);
- ei_obp(0x42, base + EN0_RSARLO);
- ei_obp(0x00, base + EN0_RSARHI);
- ei_obp(E8390_RREAD + E8390_START, base + E8390_CMD);
- /* Make certain that the dummy read has occurred. */
- udelay(6);
-#endif
-
- ei_obp(ENISR_RDC, base + EN0_ISR);
-
- /* Now the normal output. */
- ei_obp(count & 0xff, base + EN0_RCNTLO);
- ei_obp(count >> 8, base + EN0_RCNTHI);
- ei_obp(0x00, base + EN0_RSARLO);
- ei_obp(start_page, base + EN0_RSARHI);
-#endif /* 0/1 */
-
- ei_obp(E8390_RWRITE + E8390_START, base + E8390_CMD);
- if (ei_status.word16) {
- ei_osw(E8390_BASE + E8390_DATA, buf, count >> 1);
- } else {
- ei_osb(E8390_BASE + E8390_DATA, buf, count);
- }
-
-#ifdef OAKNET_DISINT
- restore_flags(flags);
-#endif
-
- start = jiffies;
-
-#ifdef OAKNET_HEADCHECK
- /*
- * This was for the ALPHA version only, but enough people have
- * been encountering problems so it is still here.
- */
-
- {
- /* DMA termination address check... */
- int addr, tries = 20;
- do {
- int high = ei_ibp(base + EN0_RSARHI);
- int low = ei_ibp(base + EN0_RSARLO);
- addr = (high << 8) + low;
- if ((start_page << 8) + count == addr)
- break;
- } while (--tries > 0);
-
- if (tries <= 0) {
- printk("%s: Tx packet transfer address mismatch,"
- "%#4.4x (expected) vs. %#4.4x (actual).\n",
- dev->name, (start_page << 8) + count, addr);
- if (retries++ == 0)
- goto retry;
- }
- }
-#endif
-
- while ((ei_ibp(base + EN0_ISR) & ENISR_RDC) == 0) {
- if (time_after(jiffies, start + OAKNET_WAIT)) {
- printk("%s: timeout waiting for Tx RDC.\n", dev->name);
- oaknet_reset_8390(dev);
- NS8390_init(dev, TRUE);
- break;
- }
- }
-
- ei_obp(ENISR_RDC, base + EN0_ISR); /* Ack intr. */
- ei_status.dmaing &= ~0x01;
-}
-
-/*
- * static void oaknet_dma_error()
- *
- * Description:
- * This routine prints out a last-ditch informative message to the console
- * indicating that a DMA error occurred. If you see this, it's the last
- * thing you'll see.
- *
- * Input(s):
- * *dev - Pointer to the device structure for this driver.
- * *name - Informative text (e.g. function name) indicating where the
- * DMA error occurred.
- *
- * Output(s):
- * N/A
- *
- * Returns:
- * N/A
- *
- */
-static void
-oaknet_dma_error(struct net_device *dev, const char *name)
-{
- printk(KERN_EMERG "%s: DMAing conflict in %s."
- "[DMAstat:%d][irqlock:%d][intr:%ld]\n",
- dev->name, name, ei_status.dmaing, ei_status.irqlock,
- dev->interrupt);
-}
-
-/*
- * Oak Ethernet module unload interface.
- */
-static void __exit oaknet_cleanup_module (void)
-{
- /* Convert to loop once driver supports multiple devices. */
- unregister_netdev(oaknet_dev);
- free_irq(oaknet_devs->irq, oaknet_devs);
- release_region(oaknet_devs->base_addr, OAKNET_IO_SIZE);
- iounmap(ioaddr);
- free_netdev(oaknet_devs);
-}
-
-module_init(oaknet_init);
-module_exit(oaknet_cleanup_module);
-MODULE_LICENSE("GPL");
projects / linux-2.6-omap-h63xx.git / commitdiff