* RTS/CTS frame should use the length of the frame plus any
* encryption overhead that will be added by the hardware.
*/
- if (!frag_skb->do_not_encrypt)
- data_length += rt2x00crypto_tx_overhead(tx_info);
+ data_length += rt2x00crypto_tx_overhead(rt2x00dev, skb);
if (tx_info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT)
ieee80211_ctstoself_get(rt2x00dev->hw, tx_info->control.vif,
EXPORT_SYMBOL_GPL(rt2x00mac_configure_filter);
#ifdef CONFIG_RT2X00_LIB_CRYPTO
+static void memcpy_tkip(struct rt2x00lib_crypto *crypto, u8 *key, u8 key_len)
+{
+ if (key_len > NL80211_TKIP_DATA_OFFSET_ENCR_KEY)
+ memcpy(&crypto->key,
+ &key[NL80211_TKIP_DATA_OFFSET_ENCR_KEY],
+ sizeof(crypto->key));
+
+ if (key_len > NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY)
+ memcpy(&crypto->tx_mic,
+ &key[NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY],
+ sizeof(crypto->tx_mic));
+
+ if (key_len > NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY)
+ memcpy(&crypto->rx_mic,
+ &key[NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY],
+ sizeof(crypto->rx_mic));
+}
+
int rt2x00mac_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
const u8 *local_address, const u8 *address,
struct ieee80211_key_conf *key)
crypto.cmd = cmd;
crypto.address = address;
- if (crypto.cipher == CIPHER_TKIP) {
- if (key->keylen > NL80211_TKIP_DATA_OFFSET_ENCR_KEY)
- memcpy(&crypto.key,
- &key->key[NL80211_TKIP_DATA_OFFSET_ENCR_KEY],
- sizeof(crypto.key));
-
- if (key->keylen > NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY)
- memcpy(&crypto.tx_mic,
- &key->key[NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY],
- sizeof(crypto.tx_mic));
-
- if (key->keylen > NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY)
- memcpy(&crypto.rx_mic,
- &key->key[NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY],
- sizeof(crypto.rx_mic));
- } else
+ if (crypto.cipher == CIPHER_TKIP)
+ memcpy_tkip(&crypto, &key->key[0], key->keylen);
+ else
memcpy(&crypto.key, &key->key[0], key->keylen);
/*
dev_kfree_skb_any(skb);
}
+static void rt2x00queue_create_tx_descriptor_seq(struct queue_entry *entry,
+ struct txentry_desc *txdesc)
+{
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
+ struct rt2x00_intf *intf = vif_to_intf(tx_info->control.vif);
+ unsigned long irqflags;
+
+ if (!(tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) ||
+ unlikely(!tx_info->control.vif))
+ return;
+
+ /*
+ * Hardware should insert sequence counter.
+ * FIXME: We insert a software sequence counter first for
+ * hardware that doesn't support hardware sequence counting.
+ *
+ * This is wrong because beacons are not getting sequence
+ * numbers assigned properly.
+ *
+ * A secondary problem exists for drivers that cannot toggle
+ * sequence counting per-frame, since those will override the
+ * sequence counter given by mac80211.
+ */
+ spin_lock_irqsave(&intf->seqlock, irqflags);
+
+ if (test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags))
+ intf->seqno += 0x10;
+ hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
+ hdr->seq_ctrl |= cpu_to_le16(intf->seqno);
+
+ spin_unlock_irqrestore(&intf->seqlock, irqflags);
+
+ __set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
+}
+
+static void rt2x00queue_create_tx_descriptor_plcp(struct queue_entry *entry,
+ struct txentry_desc *txdesc,
+ const struct rt2x00_rate *hwrate)
+{
+ struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
+ struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
+ unsigned int data_length;
+ unsigned int duration;
+ unsigned int residual;
+
+ /* Data length + CRC + Crypto overhead (IV/EIV/ICV/MIC) */
+ data_length = entry->skb->len + 4;
+ data_length += rt2x00crypto_tx_overhead(rt2x00dev, entry->skb);
+
+ /*
+ * PLCP setup
+ * Length calculation depends on OFDM/CCK rate.
+ */
+ txdesc->signal = hwrate->plcp;
+ txdesc->service = 0x04;
+
+ if (hwrate->flags & DEV_RATE_OFDM) {
+ txdesc->length_high = (data_length >> 6) & 0x3f;
+ txdesc->length_low = data_length & 0x3f;
+ } else {
+ /*
+ * Convert length to microseconds.
+ */
+ residual = GET_DURATION_RES(data_length, hwrate->bitrate);
+ duration = GET_DURATION(data_length, hwrate->bitrate);
+
+ if (residual != 0) {
+ duration++;
+
+ /*
+ * Check if we need to set the Length Extension
+ */
+ if (hwrate->bitrate == 110 && residual <= 30)
+ txdesc->service |= 0x80;
+ }
+
+ txdesc->length_high = (duration >> 8) & 0xff;
+ txdesc->length_low = duration & 0xff;
+
+ /*
+ * When preamble is enabled we should set the
+ * preamble bit for the signal.
+ */
+ if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
+ txdesc->signal |= 0x08;
+ }
+}
+
static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry,
struct txentry_desc *txdesc)
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
- struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
struct ieee80211_rate *rate =
ieee80211_get_tx_rate(rt2x00dev->hw, tx_info);
const struct rt2x00_rate *hwrate;
- unsigned int data_length;
- unsigned int duration;
- unsigned int residual;
- unsigned long irqflags;
memset(txdesc, 0, sizeof(*txdesc));
txdesc->cw_max = entry->queue->cw_max;
txdesc->aifs = entry->queue->aifs;
- /* Data length + CRC */
- data_length = entry->skb->len + 4;
-
/*
* Check whether this frame is to be acked.
*/
if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK))
__set_bit(ENTRY_TXD_ACK, &txdesc->flags);
- if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags) &&
- !entry->skb->do_not_encrypt) {
- /* Apply crypto specific descriptor information */
- rt2x00crypto_create_tx_descriptor(entry, txdesc);
-
- /*
- * Extend frame length to include all encryption overhead
- * that will be added by the hardware.
- */
- data_length += rt2x00crypto_tx_overhead(tx_info);
- }
-
/*
* Check if this is a RTS/CTS frame
*/
* Set ifs to IFS_SIFS when the this is not the first fragment,
* or this fragment came after RTS/CTS.
*/
- if (test_bit(ENTRY_TXD_RTS_FRAME, &txdesc->flags)) {
- txdesc->ifs = IFS_SIFS;
- } else if (tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) {
+ if ((tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) &&
+ !test_bit(ENTRY_TXD_RTS_FRAME, &txdesc->flags)) {
__set_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags);
txdesc->ifs = IFS_BACKOFF;
- } else {
+ } else
txdesc->ifs = IFS_SIFS;
- }
- /*
- * Hardware should insert sequence counter.
- * FIXME: We insert a software sequence counter first for
- * hardware that doesn't support hardware sequence counting.
- *
- * This is wrong because beacons are not getting sequence
- * numbers assigned properly.
- *
- * A secondary problem exists for drivers that cannot toggle
- * sequence counting per-frame, since those will override the
- * sequence counter given by mac80211.
- */
- if (tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- if (likely(tx_info->control.vif)) {
- struct rt2x00_intf *intf;
-
- intf = vif_to_intf(tx_info->control.vif);
-
- spin_lock_irqsave(&intf->seqlock, irqflags);
-
- if (test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags))
- intf->seqno += 0x10;
- hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
- hdr->seq_ctrl |= cpu_to_le16(intf->seqno);
-
- spin_unlock_irqrestore(&intf->seqlock, irqflags);
-
- __set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
- }
- }
-
- /*
- * PLCP setup
- * Length calculation depends on OFDM/CCK rate.
- */
hwrate = rt2x00_get_rate(rate->hw_value);
- txdesc->signal = hwrate->plcp;
- txdesc->service = 0x04;
-
- if (hwrate->flags & DEV_RATE_OFDM) {
+ if (hwrate->flags & DEV_RATE_OFDM)
__set_bit(ENTRY_TXD_OFDM_RATE, &txdesc->flags);
- txdesc->length_high = (data_length >> 6) & 0x3f;
- txdesc->length_low = data_length & 0x3f;
- } else {
- /*
- * Convert length to microseconds.
- */
- residual = GET_DURATION_RES(data_length, hwrate->bitrate);
- duration = GET_DURATION(data_length, hwrate->bitrate);
-
- if (residual != 0) {
- duration++;
-
- /*
- * Check if we need to set the Length Extension
- */
- if (hwrate->bitrate == 110 && residual <= 30)
- txdesc->service |= 0x80;
- }
-
- txdesc->length_high = (duration >> 8) & 0xff;
- txdesc->length_low = duration & 0xff;
-
- /*
- * When preamble is enabled we should set the
- * preamble bit for the signal.
- */
- if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
- txdesc->signal |= 0x08;
- }
+ /*
+ * Apply TX descriptor handling by components
+ */
+ rt2x00crypto_create_tx_descriptor(entry, txdesc);
+ rt2x00queue_create_tx_descriptor_seq(entry, txdesc);
+ rt2x00queue_create_tx_descriptor_plcp(entry, txdesc, hwrate);
}
static void rt2x00queue_write_tx_descriptor(struct queue_entry *entry,
projects / linux-2.6-omap-h63xx.git / commitdiff