# AT91 Board Options
#
CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ONENAND is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-# CONFIG_MTD_NAND_AT91_ECC_SOFT is not set
-CONFIG_MTD_NAND_AT91_ECC_HW=y
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+# CONFIG_MTD_NAND_ATMEL_ECC_SOFT is not set
+CONFIG_MTD_NAND_ATMEL_ECC_HW=y
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_ONENAND is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_ALAUDA is not set
help
Enable support for the DataFlash card.
-config MTD_NAND_AT91_BUSWIDTH_16
+config MTD_NAND_ATMEL_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
help
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
// .rdy_pin = ... not connected
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
.rdy_pin = AT91_PIN_PC15,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
}
/* det_pin is not connected */
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
/* AMD */
-#define AM29DL800BB 0x22C8
+#define AM29DL800BB 0x22CB
#define AM29DL800BT 0x224A
#define AM29F800BB 0x2258
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/mutex.h>
+#include <linux/err.h>
+
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
device->write = dataflash_write;
device->priv = priv;
- dev_info(&spi->dev, "%s (%d KBytes) pagesize %d bytes, "
- "erasesize %d bytes\n", name, device->size/1024,
- pagesize, pagesize * 8); /* 8 pages = 1 block */
+ dev_info(&spi->dev, "%s (%d KBytes) pagesize %d bytes\n",
+ name, DIV_ROUND_UP(device->size, 1024), pagesize);
dev_set_drvdata(&spi->dev, priv);
if (mtd_has_partitions()) {
return add_mtd_device(device) == 1 ? -ENODEV : 0;
}
-/*
- * Detect and initialize DataFlash device:
- *
- * Device Density ID code #Pages PageSize Offset
- * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
- * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
- * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
- * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
- * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
- * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
- * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
- * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
- */
-
struct flash_info {
char *name;
- /* JEDEC id zero means "no ID" (most older chips); otherwise it has
- * a high byte of zero plus three data bytes: the manufacturer id,
- * then a two byte device id.
+ /* JEDEC id has a high byte of zero plus three data bytes:
+ * the manufacturer id, then a two byte device id.
*/
uint32_t jedec_id;
- /* The size listed here is what works with OPCODE_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
+ /* The size listed here is what works with OP_ERASE_PAGE. */
unsigned nr_pages;
uint16_t pagesize;
uint16_t pageoffset;
uint16_t flags;
-#define SUP_POW2PS 0x02
-#define IS_POW2PS 0x01
+#define SUP_POW2PS 0x0002 /* supports 2^N byte pages */
+#define IS_POW2PS 0x0001 /* uses 2^N byte pages */
};
static struct flash_info __devinitdata dataflash_data [] = {
- { "at45db011d", 0x1f2200, 512, 264, 9, SUP_POW2PS},
+ /*
+ * NOTE: chips with SUP_POW2PS (rev D and up) need two entries,
+ * one with IS_POW2PS and the other without. The entry with the
+ * non-2^N byte page size can't name exact chip revisions without
+ * losing backwards compatibility for cmdlinepart.
+ *
+ * These newer chips also support 128-byte security registers (with
+ * 64 bytes one-time-programmable) and software write-protection.
+ */
+ { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS},
{ "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db021d", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
+ { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
{ "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db041d", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
+ { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
{ "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db081d", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
+ { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
{ "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db161d", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
+ { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
{ "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
- { "at45db321c", 0x1f2700, 8192, 528, 10, },
+ { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */
- { "at45db321d", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
+ { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
{ "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
- { "at45db641d", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
- { "at45db641d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
+ { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
+ { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
};
static struct flash_info *__devinit jedec_probe(struct spi_device *spi)
struct flash_info *info;
int status;
-
/* JEDEC also defines an optional "extended device information"
* string for after vendor-specific data, after the three bytes
* we use here. Supporting some chips might require using it.
+ *
+ * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
+ * That's not an error; only rev C and newer chips handle it, and
+ * only Atmel sells these chips.
*/
tmp = spi_write_then_read(spi, &code, 1, id, 3);
if (tmp < 0) {
DEBUG(MTD_DEBUG_LEVEL0, "%s: error %d reading JEDEC ID\n",
spi->dev.bus_id, tmp);
- return NULL;
+ return ERR_PTR(tmp);
}
+ if (id[0] != 0x1f)
+ return NULL;
+
jedec = id[0];
jedec = jedec << 8;
jedec |= id[1];
tmp < ARRAY_SIZE(dataflash_data);
tmp++, info++) {
if (info->jedec_id == jedec) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: OTP, sector protect%s\n",
+ dev_name(&spi->dev),
+ (info->flags & SUP_POW2PS)
+ ? ", binary pagesize" : ""
+ );
if (info->flags & SUP_POW2PS) {
status = dataflash_status(spi);
- if (status & 0x1)
- /* return power of 2 pagesize */
- return ++info;
- else
- return info;
+ if (status < 0) {
+ DEBUG(MTD_DEBUG_LEVEL1,
+ "%s: status error %d\n",
+ dev_name(&spi->dev), status);
+ return ERR_PTR(status);
+ }
+ if (status & 0x1) {
+ if (info->flags & IS_POW2PS)
+ return info;
+ } else {
+ if (!(info->flags & IS_POW2PS))
+ return info;
+ }
}
}
}
- return NULL;
+
+ /*
+ * Treat other chips as errors ... we won't know the right page
+ * size (it might be binary) even when we can tell which density
+ * class is involved (legacy chip id scheme).
+ */
+ dev_warn(&spi->dev, "JEDEC id %06x not handled\n", jedec);
+ return ERR_PTR(-ENODEV);
}
+/*
+ * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
+ * or else the ID code embedded in the status bits:
+ *
+ * Device Density ID code #Pages PageSize Offset
+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
+ * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
+ */
static int __devinit dataflash_probe(struct spi_device *spi)
{
int status;
* If it succeeds we know we have either a C or D part.
* D will support power of 2 pagesize option.
*/
-
info = jedec_probe(spi);
-
+ if (IS_ERR(info))
+ return PTR_ERR(info);
if (info != NULL)
return add_dataflash(spi, info->name, info->nr_pages,
info->pagesize, info->pageoffset);
-
+ /*
+ * Older chips support only legacy commands, identifing
+ * capacity using bits in the status byte.
+ */
status = dataflash_status(spi);
if (status <= 0 || status == 0xff) {
DEBUG(MTD_DEBUG_LEVEL1, "%s: status error %d\n",
status = add_dataflash(spi, "AT45DB021B", 1024, 264, 9);
break;
case 0x1c: /* 0 1 1 1 x x */
- status = add_dataflash(spi, "AT45DB041B", 2048, 264, 9);
+ status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9);
break;
case 0x24: /* 1 0 0 1 x x */
status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9);
break;
case 0x2c: /* 1 0 1 1 x x */
- status = add_dataflash(spi, "AT45DB161B", 4096, 528, 10);
+ status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10);
break;
case 0x34: /* 1 1 0 1 x x */
status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10);
config MTD_NAND_BF5XX_HWECC
bool "BF5XX NAND Hardware ECC"
+ default y
depends on MTD_NAND_BF5XX
help
Enable the use of the BF5XX's internal ECC generator when
using NAND.
+config MTD_NAND_BF5XX_BOOTROM_ECC
+ bool "Use Blackfin BootROM ECC Layout"
+ default n
+ depends on MTD_NAND_BF5XX_HWECC
+ help
+ If you wish to modify NAND pages and allow the Blackfin on-chip
+ BootROM to boot from them, say Y here. This is only necessary
+ if you are booting U-Boot out of NAND and you wish to update
+ U-Boot from Linux' userspace. Otherwise, you should say N here.
+
+ If unsure, say N.
+
config MTD_NAND_RTC_FROM4
tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
depends on SH_SOLUTION_ENGINE
P_NAND_ALE,
0};
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+static uint8_t bbt_pattern[] = { 0xff };
+
+static struct nand_bbt_descr bootrom_bbt = {
+ .options = 0,
+ .offs = 63,
+ .len = 1,
+ .pattern = bbt_pattern,
+};
+
+static struct nand_ecclayout bootrom_ecclayout = {
+ .eccbytes = 24,
+ .eccpos = {
+ 0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
+ 0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
+ 0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
+ 0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
+ 0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
+ 0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
+ 0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
+ 0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
+ },
+ .oobfree = {
+ { 0x8 * 0 + 3, 5 },
+ { 0x8 * 1 + 3, 5 },
+ { 0x8 * 2 + 3, 5 },
+ { 0x8 * 3 + 3, 5 },
+ { 0x8 * 4 + 3, 5 },
+ { 0x8 * 5 + 3, 5 },
+ { 0x8 * 6 + 3, 5 },
+ { 0x8 * 7 + 3, 5 },
+ }
+};
+#endif
+
/*
* Data structures for bf5xx nand flash controller driver
*/
dat += 256;
read_ecc += 8;
calc_ecc += 8;
- ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
+ ret |= bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
}
return ret;
ecc0 = bfin_read_NFC_ECC0();
ecc1 = bfin_read_NFC_ECC1();
- code[0] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
+ code[0] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
dev_dbg(info->device, "returning ecc 0x%08x\n", code[0]);
if (page_size == 512) {
ecc0 = bfin_read_NFC_ECC2();
ecc1 = bfin_read_NFC_ECC3();
- code[1] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
+ code[1] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
/* second 3 bytes in ecc_code for second 256
* bytes of 512 page size
/*
* System initialization functions
*/
-
static int bf5xx_nand_dma_init(struct bf5xx_nand_info *info)
{
int ret;
return 0;
}
+static void bf5xx_nand_dma_remove(struct bf5xx_nand_info *info)
+{
+ /* Free NFC DMA channel */
+ if (hardware_ecc)
+ free_dma(CH_NFC);
+}
+
/*
* BF5XX NFC hardware initialization
* - pin mux setup
#endif
}
-static int bf5xx_nand_remove(struct platform_device *pdev)
+static int __devexit bf5xx_nand_remove(struct platform_device *pdev)
{
struct bf5xx_nand_info *info = to_nand_info(pdev);
struct mtd_info *mtd = NULL;
}
peripheral_free_list(bfin_nfc_pin_req);
+ bf5xx_nand_dma_remove(info);
/* free the common resources */
kfree(info);
* it can allocate all necessary resources then calls the
* nand layer to look for devices
*/
-static int bf5xx_nand_probe(struct platform_device *pdev)
+static int __devinit bf5xx_nand_probe(struct platform_device *pdev)
{
struct bf5xx_nand_platform *plat = to_nand_plat(pdev);
struct bf5xx_nand_info *info = NULL;
dev_dbg(&pdev->dev, "(%p)\n", pdev);
- if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
- printk(KERN_ERR DRV_NAME
- ": Requesting Peripherals failed\n");
- return -EFAULT;
- }
-
if (!plat) {
dev_err(&pdev->dev, "no platform specific information\n");
- goto exit_error;
+ return -EINVAL;
+ }
+
+ if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
+ dev_err(&pdev->dev, "requesting Peripherals failed\n");
+ return -EFAULT;
}
info = kzalloc(sizeof(*info), GFP_KERNEL);
if (info == NULL) {
dev_err(&pdev->dev, "no memory for flash info\n");
err = -ENOMEM;
- goto exit_error;
+ goto out_err_kzalloc;
}
platform_set_drvdata(pdev, info);
/* initialise the hardware */
err = bf5xx_nand_hw_init(info);
- if (err != 0)
- goto exit_error;
+ if (err)
+ goto out_err_hw_init;
/* setup hardware ECC data struct */
if (hardware_ecc) {
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+ chip->badblock_pattern = &bootrom_bbt;
+ chip->ecc.layout = &bootrom_ecclayout;
+#endif
+
if (plat->page_size == NFC_PG_SIZE_256) {
chip->ecc.bytes = 3;
chip->ecc.size = 256;
/* scan hardware nand chip and setup mtd info data struct */
if (nand_scan(mtd, 1)) {
err = -ENXIO;
- goto exit_error;
+ goto out_err_nand_scan;
}
/* add NAND partition */
dev_dbg(&pdev->dev, "initialised ok\n");
return 0;
-exit_error:
- bf5xx_nand_remove(pdev);
+out_err_nand_scan:
+ bf5xx_nand_dma_remove(info);
+out_err_hw_init:
+ platform_set_drvdata(pdev, NULL);
+ kfree(info);
+out_err_kzalloc:
+ peripheral_free_list(bfin_nfc_pin_req);
- if (err == 0)
- err = -EINVAL;
return err;
}
/* driver device registration */
static struct platform_driver bf5xx_nand_driver = {
.probe = bf5xx_nand_probe,
- .remove = bf5xx_nand_remove,
+ .remove = __devexit_p(bf5xx_nand_remove),
.suspend = bf5xx_nand_suspend,
.resume = bf5xx_nand_resume,
.driver = {
goto out;
mh = (struct NFTLMediaHeader *)buf;
- mh->NumEraseUnits = le16_to_cpu(mh->NumEraseUnits);
- mh->FirstPhysicalEUN = le16_to_cpu(mh->FirstPhysicalEUN);
- mh->FormattedSize = le32_to_cpu(mh->FormattedSize);
+ le16_to_cpus(&mh->NumEraseUnits);
+ le16_to_cpus(&mh->FirstPhysicalEUN);
+ le32_to_cpus(&mh->FormattedSize);
printk(KERN_INFO " DataOrgID = %s\n"
" NumEraseUnits = %d\n"
doc->mh1_page = doc->mh0_page + (4096 >> this->page_shift);
mh = (struct INFTLMediaHeader *)buf;
- mh->NoOfBootImageBlocks = le32_to_cpu(mh->NoOfBootImageBlocks);
- mh->NoOfBinaryPartitions = le32_to_cpu(mh->NoOfBinaryPartitions);
- mh->NoOfBDTLPartitions = le32_to_cpu(mh->NoOfBDTLPartitions);
- mh->BlockMultiplierBits = le32_to_cpu(mh->BlockMultiplierBits);
- mh->FormatFlags = le32_to_cpu(mh->FormatFlags);
- mh->PercentUsed = le32_to_cpu(mh->PercentUsed);
+ le32_to_cpus(&mh->NoOfBootImageBlocks);
+ le32_to_cpus(&mh->NoOfBinaryPartitions);
+ le32_to_cpus(&mh->NoOfBDTLPartitions);
+ le32_to_cpus(&mh->BlockMultiplierBits);
+ le32_to_cpus(&mh->FormatFlags);
+ le32_to_cpus(&mh->PercentUsed);
printk(KERN_INFO " bootRecordID = %s\n"
" NoOfBootImageBlocks = %d\n"
/* Scan the partitions */
for (i = 0; (i < 4); i++) {
ip = &(mh->Partitions[i]);
- ip->virtualUnits = le32_to_cpu(ip->virtualUnits);
- ip->firstUnit = le32_to_cpu(ip->firstUnit);
- ip->lastUnit = le32_to_cpu(ip->lastUnit);
- ip->flags = le32_to_cpu(ip->flags);
- ip->spareUnits = le32_to_cpu(ip->spareUnits);
- ip->Reserved0 = le32_to_cpu(ip->Reserved0);
+ le32_to_cpus(&ip->virtualUnits);
+ le32_to_cpus(&ip->firstUnit);
+ le32_to_cpus(&ip->lastUnit);
+ le32_to_cpus(&ip->flags);
+ le32_to_cpus(&ip->spareUnits);
+ le32_to_cpus(&ip->Reserved0);
printk(KERN_INFO " PARTITION[%d] ->\n"
" virtualUnits = %d\n"
goto err;
}
- priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", res.start);
+ priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start);
if (!priv->mtd.name) {
ret = -ENOMEM;
goto err;
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/vmalloc.h>
+#include <asm/div64.h>
#include <linux/slab.h>
#include <linux/errno.h>
#include <linux/string.h>
#define STATE_CMD_READID 0x0000000A /* read ID */
#define STATE_CMD_ERASE2 0x0000000B /* sector erase second command */
#define STATE_CMD_RESET 0x0000000C /* reset */
+#define STATE_CMD_RNDOUT 0x0000000D /* random output command */
+#define STATE_CMD_RNDOUTSTART 0x0000000E /* random output start command */
#define STATE_CMD_MASK 0x0000000F /* command states mask */
/* After an address is input, the simulator goes to one of these states */
#define STATE_ADDR_PAGE 0x00000010 /* full (row, column) address is accepted */
#define STATE_ADDR_SEC 0x00000020 /* sector address was accepted */
-#define STATE_ADDR_ZERO 0x00000030 /* one byte zero address was accepted */
-#define STATE_ADDR_MASK 0x00000030 /* address states mask */
+#define STATE_ADDR_COLUMN 0x00000030 /* column address was accepted */
+#define STATE_ADDR_ZERO 0x00000040 /* one byte zero address was accepted */
+#define STATE_ADDR_MASK 0x00000070 /* address states mask */
/* Durind data input/output the simulator is in these states */
#define STATE_DATAIN 0x00000100 /* waiting for data input */
#define ACTION_OOBOFF 0x00600000 /* add to address OOB offset */
#define ACTION_MASK 0x00700000 /* action mask */
-#define NS_OPER_NUM 12 /* Number of operations supported by the simulator */
+#define NS_OPER_NUM 13 /* Number of operations supported by the simulator */
#define NS_OPER_STATES 6 /* Maximum number of states in operation */
#define OPT_ANY 0xFFFFFFFF /* any chip supports this operation */
{OPT_ANY, {STATE_CMD_READID, STATE_ADDR_ZERO, STATE_DATAOUT_ID, STATE_READY}},
/* Large page devices read page */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART | ACTION_CPY,
- STATE_DATAOUT, STATE_READY}}
+ STATE_DATAOUT, STATE_READY}},
+ /* Large page devices random page read */
+ {OPT_LARGEPAGE, {STATE_CMD_RNDOUT, STATE_ADDR_COLUMN, STATE_CMD_RNDOUTSTART | ACTION_CPY,
+ STATE_DATAOUT, STATE_READY}},
};
struct weak_block {
if (ns->busw == 16)
NS_WARN("16-bit flashes support wasn't tested\n");
- printk("flash size: %llu MiB\n", ns->geom.totsz >> 20);
+ printk("flash size: %llu MiB\n",
+ (unsigned long long)ns->geom.totsz >> 20);
printk("page size: %u bytes\n", ns->geom.pgsz);
printk("OOB area size: %u bytes\n", ns->geom.oobsz);
printk("sector size: %u KiB\n", ns->geom.secsz >> 10);
printk("bus width: %u\n", ns->busw);
printk("bits in sector size: %u\n", ns->geom.secshift);
printk("bits in page size: %u\n", ns->geom.pgshift);
- printk("bits in OOB size: %u\n", ns->geom.oobshift);
- printk("flash size with OOB: %llu KiB\n", ns->geom.totszoob >> 10);
+ printk("bits in OOB size: %u\n", ns->geom.oobshift);
+ printk("flash size with OOB: %llu KiB\n",
+ (unsigned long long)ns->geom.totszoob >> 10);
printk("page address bytes: %u\n", ns->geom.pgaddrbytes);
printk("sector address bytes: %u\n", ns->geom.secaddrbytes);
printk("options: %#x\n", ns->options);
return "STATE_CMD_ERASE2";
case STATE_CMD_RESET:
return "STATE_CMD_RESET";
+ case STATE_CMD_RNDOUT:
+ return "STATE_CMD_RNDOUT";
+ case STATE_CMD_RNDOUTSTART:
+ return "STATE_CMD_RNDOUTSTART";
case STATE_ADDR_PAGE:
return "STATE_ADDR_PAGE";
case STATE_ADDR_SEC:
return "STATE_ADDR_SEC";
case STATE_ADDR_ZERO:
return "STATE_ADDR_ZERO";
+ case STATE_ADDR_COLUMN:
+ return "STATE_ADDR_COLUMN";
case STATE_DATAIN:
return "STATE_DATAIN";
case STATE_DATAOUT:
switch (cmd) {
case NAND_CMD_READ0:
+ case NAND_CMD_READ1:
case NAND_CMD_READSTART:
case NAND_CMD_PAGEPROG:
case NAND_CMD_READOOB:
case NAND_CMD_READID:
case NAND_CMD_ERASE2:
case NAND_CMD_RESET:
- case NAND_CMD_READ1:
+ case NAND_CMD_RNDOUT:
+ case NAND_CMD_RNDOUTSTART:
return 0;
case NAND_CMD_STATUS_MULTI:
return STATE_CMD_ERASE2;
case NAND_CMD_RESET:
return STATE_CMD_RESET;
+ case NAND_CMD_RNDOUT:
+ return STATE_CMD_RNDOUT;
+ case NAND_CMD_RNDOUTSTART:
+ return STATE_CMD_RNDOUTSTART;
}
NS_ERR("get_state_by_command: unknown command, BUG\n");
ns->regs.num = 1;
break;
+ case STATE_ADDR_COLUMN:
+ /* Column address is always 2 bytes */
+ ns->regs.num = ns->geom.pgaddrbytes - ns->geom.secaddrbytes;
+ break;
+
default:
NS_ERR("switch_state: BUG! unknown address state\n");
}
return;
}
- /*
- * Chip might still be in STATE_DATAOUT
- * (if OPT_AUTOINCR feature is supported), STATE_DATAOUT_STATUS or
- * STATE_DATAOUT_STATUS_M state. If so, switch state.
- */
+ /* Check that the command byte is correct */
+ if (check_command(byte)) {
+ NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
+ return;
+ }
+
if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS
|| NS_STATE(ns->state) == STATE_DATAOUT_STATUS_M
- || ((ns->options & OPT_AUTOINCR) && NS_STATE(ns->state) == STATE_DATAOUT))
+ || NS_STATE(ns->state) == STATE_DATAOUT) {
+ int row = ns->regs.row;
+
switch_state(ns);
+ if (byte == NAND_CMD_RNDOUT)
+ ns->regs.row = row;
+ }
/* Check if chip is expecting command */
if (NS_STATE(ns->nxstate) != STATE_UNKNOWN && !(ns->nxstate & STATE_CMD_MASK)) {
switch_to_ready_state(ns, NS_STATUS_FAILED(ns));
}
- /* Check that the command byte is correct */
- if (check_command(byte)) {
- NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
- return;
- }
-
NS_DBG("command byte corresponding to %s state accepted\n",
get_state_name(get_state_by_command(byte)));
ns->regs.command = byte;
int jffs2_sum_init(struct jffs2_sb_info *c)
{
+ uint32_t sum_size = max_t(uint32_t, c->sector_size, MAX_SUMMARY_SIZE);
+
c->summary = kzalloc(sizeof(struct jffs2_summary), GFP_KERNEL);
if (!c->summary) {
return -ENOMEM;
}
- c->summary->sum_buf = vmalloc(c->sector_size);
+ c->summary->sum_buf = kmalloc(sum_size, GFP_KERNEL);
if (!c->summary->sum_buf) {
JFFS2_WARNING("Can't allocate buffer for writing out summary information!\n");
jffs2_sum_disable_collecting(c->summary);
- vfree(c->summary->sum_buf);
+ kfree(c->summary->sum_buf);
c->summary->sum_buf = NULL;
kfree(c->summary);
/* Write summary data to flash - helper function for jffs2_sum_write_sumnode() */
static int jffs2_sum_write_data(struct jffs2_sb_info *c, struct jffs2_eraseblock *jeb,
- uint32_t infosize, uint32_t datasize, int padsize)
+ uint32_t infosize, uint32_t datasize, int padsize)
{
struct jffs2_raw_summary isum;
union jffs2_sum_mem *temp;
int ret;
size_t retlen;
+ if (padsize + datasize > MAX_SUMMARY_SIZE) {
+ /* It won't fit in the buffer. Abort summary for this jeb */
+ jffs2_sum_disable_collecting(c->summary);
+
+ JFFS2_WARNING("Summary too big (%d data, %d pad) in eraseblock at %08x\n",
+ datasize, padsize, jeb->offset);
+ /* Non-fatal */
+ return 0;
+ }
+ /* Is there enough space for summary? */
+ if (padsize < 0) {
+ /* don't try to write out summary for this jeb */
+ jffs2_sum_disable_collecting(c->summary);
+
+ JFFS2_WARNING("Not enough space for summary, padsize = %d\n",
+ padsize);
+ /* Non-fatal */
+ return 0;
+ }
+
memset(c->summary->sum_buf, 0xff, datasize);
memset(&isum, 0, sizeof(isum));
{
int datasize, infosize, padsize;
struct jffs2_eraseblock *jeb;
- int ret;
+ int ret = 0;
dbg_summary("called\n");
infosize += padsize;
datasize += padsize;
- /* Is there enough space for summary? */
- if (padsize < 0) {
- /* don't try to write out summary for this jeb */
- jffs2_sum_disable_collecting(c->summary);
-
- JFFS2_WARNING("Not enough space for summary, padsize = %d\n", padsize);
- spin_lock(&c->erase_completion_lock);
- return 0;
- }
-
ret = jffs2_sum_write_data(c, jeb, infosize, datasize, padsize);
spin_lock(&c->erase_completion_lock);
return ret;
#ifndef JFFS2_SUMMARY_H
#define JFFS2_SUMMARY_H
+/* Limit summary size to 64KiB so that we can kmalloc it. If the summary
+ is larger than that, we have to just ditch it and avoid using summary
+ for the eraseblock in question... and it probably doesn't hurt us much
+ anyway. */
+#define MAX_SUMMARY_SIZE 65536
+
#include <linux/uio.h>
#include <linux/jffs2.h>
printk(KERN_INFO args); \
} while(0)
#else /* CONFIG_MTD_DEBUG */
-#define DEBUG(n, args...) do { } while(0)
+#define DEBUG(n, args...) \
+ do { \
+ if (0) \
+ printk(KERN_INFO args); \
+ } while(0)
#endif /* CONFIG_MTD_DEBUG */
#define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING))
#define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
#define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK))
-#define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT))
+/* Large page NAND with SOFT_ECC should support subpage reads */
+#define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \
+ && (chip->page_shift > 9))
/* Mask to zero out the chip options, which come from the id table */
#define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR)