- info, major/minor #'s for Compaq's SMART Array Controllers.
cdrom/
- directory with information on the CD-ROM drivers that Linux has.
-cli-sti-removal.txt
- - cli()/sti() removal guide.
computone.txt
- info on Computone Intelliport II/Plus Multiport Serial Driver.
connector/
--- /dev/null
+What: /sys/class/regulator/.../state
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ state. This holds the regulator output state.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'unknown'
+
+ 'enabled' means the regulator output is ON and is supplying
+ power to the system.
+
+ 'disabled' means the regulator output is OFF and is not
+ supplying power to the system..
+
+ 'unknown' means software cannot determine the state.
+
+ NOTE: this field can be used in conjunction with microvolts
+ and microamps to determine regulator output levels.
+
+
+What: /sys/class/regulator/.../type
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ type. This holds the regulator type.
+
+ This will be one of the following strings:
+
+ 'voltage'
+ 'current'
+ 'unknown'
+
+ 'voltage' means the regulator output voltage can be controlled
+ by software.
+
+ 'current' means the regulator output current limit can be
+ controlled by software.
+
+ 'unknown' means software cannot control either voltage or
+ current limit.
+
+
+What: /sys/class/regulator/.../microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ microvolts. This holds the regulator output voltage setting
+ measured in microvolts (i.e. E-6 Volts).
+
+ NOTE: This value should not be used to determine the regulator
+ output voltage level as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ microamps. This holds the regulator output current limit
+ setting measured in microamps (i.e. E-6 Amps).
+
+ NOTE: This value should not be used to determine the regulator
+ output current level as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../opmode
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ opmode. This holds the regulator operating mode setting.
+
+ The opmode value can be one of the following strings:
+
+ 'fast'
+ 'normal'
+ 'idle'
+ 'standby'
+ 'unknown'
+
+ The modes are described in include/linux/regulator/regulator.h
+
+ NOTE: This value should not be used to determine the regulator
+ output operating mode as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../min_microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ min_microvolts. This holds the minimum safe working regulator
+ output voltage setting for this domain measured in microvolts.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no min microvolts constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../max_microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ max_microvolts. This holds the maximum safe working regulator
+ output voltage setting for this domain measured in microvolts.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no max microvolts constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../min_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ min_microamps. This holds the minimum safe working regulator
+ output current limit setting for this domain measured in
+ microamps.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no min microamps constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../max_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ max_microamps. This holds the maximum safe working regulator
+ output current limit setting for this domain measured in
+ microamps.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no max microamps constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../num_users
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ num_users. This holds the number of consumer devices that
+ have called regulator_enable() on this regulator.
+
+
+What: /sys/class/regulator/.../requested_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ requested_microamps. This holds the total requested load
+ current in microamps for this regulator from all its consumer
+ devices.
+
+
+What: /sys/class/regulator/.../parent
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Some regulator directories will contain a link called parent.
+ This points to the parent or supply regulator if one exists.
+
+What: /sys/class/regulator/.../suspend_mem_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to memory.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to memory voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_disk_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to disk.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to disk voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_standby_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to standby.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to standby voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_mem_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to
+ memory.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to memory mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_disk_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to disk.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to disk mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_standby_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to
+ standby.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to standby mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_mem_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_state. This holds the regulator operating state
+ when suspended to memory.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
+
+What: /sys/class/regulator/.../suspend_disk_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_state. This holds the regulator operating state
+ when suspended to disk.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
+
+What: /sys/class/regulator/.../suspend_standby_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_state. This holds the regulator operating
+ state when suspended to standby.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
kernel-api.xml filesystems.xml lsm.xml usb.xml kgdb.xml \
gadget.xml libata.xml mtdnand.xml librs.xml rapidio.xml \
genericirq.xml s390-drivers.xml uio-howto.xml scsi.xml \
- mac80211.xml debugobjects.xml
+ mac80211.xml debugobjects.xml sh.xml
###
# The build process is as follows (targets):
"Kernel debugging" select "KGDB: kernel debugging with remote gdb".
</para>
<para>
+ It is advised, but not required that you turn on the
+ CONFIG_FRAME_POINTER kernel option. This option inserts code to
+ into the compiled executable which saves the frame information in
+ registers or on the stack at different points which will allow a
+ debugger such as gdb to more accurately construct stack back traces
+ while debugging the kernel.
+ </para>
+ <para>
+ If the architecture that you are using supports the kernel option
+ CONFIG_DEBUG_RODATA, you should consider turning it off. This
+ option will prevent the use of software breakpoints because it
+ marks certain regions of the kernel's memory space as read-only.
+ If kgdb supports it for the architecture you are using, you can
+ use hardware breakpoints if you desire to run with the
+ CONFIG_DEBUG_RODATA option turned on, else you need to turn off
+ this option.
+ </para>
+ <para>
Next you should choose one of more I/O drivers to interconnect debugging
host and debugged target. Early boot debugging requires a KGDB
I/O driver that supports early debugging and the driver must be
the hardware structures represented here, please consult the Principles
of Operation.
</para>
-!Iinclude/asm-s390/cio.h
+!Iarch/s390/include/asm/cio.h
</sect1>
<sect1 id="ccwdev">
<title>ccw devices</title>
ccw device structure. Device drivers must not bypass those functions
or strange side effects may happen.
</para>
-!Iinclude/asm-s390/ccwdev.h
+!Iarch/s390/include/asm/ccwdev.h
!Edrivers/s390/cio/device.c
!Edrivers/s390/cio/device_ops.c
</sect1>
measurement data which is made available by the channel subsystem
for each channel attached device.
</para>
-!Iinclude/asm-s390/cmb.h
+!Iarch/s390/include/asm/cmb.h
!Edrivers/s390/cio/cmf.c
</sect1>
</chapter>
</para>
<sect1 id="ccwgroupdevices">
<title>ccw group devices</title>
-!Iinclude/asm-s390/ccwgroup.h
+!Iarch/s390/include/asm/ccwgroup.h
!Edrivers/s390/cio/ccwgroup.c
</sect1>
</chapter>
--- /dev/null
+<?xml version="1.0" encoding="UTF-8"?>
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.1.2//EN"
+ "http://www.oasis-open.org/docbook/xml/4.1.2/docbookx.dtd" []>
+
+<book id="sh-drivers">
+ <bookinfo>
+ <title>SuperH Interfaces Guide</title>
+
+ <authorgroup>
+ <author>
+ <firstname>Paul</firstname>
+ <surname>Mundt</surname>
+ <affiliation>
+ <address>
+ <email>lethal@linux-sh.org</email>
+ </address>
+ </affiliation>
+ </author>
+ </authorgroup>
+
+ <copyright>
+ <year>2008</year>
+ <holder>Paul Mundt</holder>
+ </copyright>
+ <copyright>
+ <year>2008</year>
+ <holder>Renesas Technology Corp.</holder>
+ </copyright>
+
+ <legalnotice>
+ <para>
+ This documentation is free software; you can redistribute
+ it and/or modify it under the terms of the GNU General Public
+ License version 2 as published by the Free Software Foundation.
+ </para>
+
+ <para>
+ This program is distributed in the hope that it will be
+ useful, but WITHOUT ANY WARRANTY; without even the implied
+ warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ See the GNU General Public License for more details.
+ </para>
+
+ <para>
+ You should have received a copy of the GNU General Public
+ License along with this program; if not, write to the Free
+ Software Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ MA 02111-1307 USA
+ </para>
+
+ <para>
+ For more details see the file COPYING in the source
+ distribution of Linux.
+ </para>
+ </legalnotice>
+ </bookinfo>
+
+<toc></toc>
+
+ <chapter id="mm">
+ <title>Memory Management</title>
+ <sect1 id="sh4">
+ <title>SH-4</title>
+ <sect2 id="sq">
+ <title>Store Queue API</title>
+!Earch/sh/kernel/cpu/sh4/sq.c
+ </sect2>
+ </sect1>
+ <sect1 id="sh5">
+ <title>SH-5</title>
+ <sect2 id="tlb">
+ <title>TLB Interfaces</title>
+!Iarch/sh/mm/tlb-sh5.c
+!Iarch/sh/include/asm/tlb_64.h
+ </sect2>
+ </sect1>
+ </chapter>
+ <chapter id="clk">
+ <title>Clock Framework Extensions</title>
+!Iarch/sh/include/asm/clock.h
+ </chapter>
+ <chapter id="mach">
+ <title>Machine Specific Interfaces</title>
+ <sect1 id="dreamcast">
+ <title>mach-dreamcast</title>
+!Iarch/sh/boards/mach-dreamcast/rtc.c
+ </sect1>
+ <sect1 id="x3proto">
+ <title>mach-x3proto</title>
+!Earch/sh/boards/mach-x3proto/ilsel.c
+ </sect1>
+ </chapter>
+ <chapter id="busses">
+ <title>Busses</title>
+ <sect1 id="superhyway">
+ <title>SuperHyway</title>
+!Edrivers/sh/superhyway/superhyway.c
+ </sect1>
+
+ <sect1 id="maple">
+ <title>Maple</title>
+!Edrivers/sh/maple/maple.c
+ </sect1>
+ </chapter>
+</book>
<chapter id="pubfunctions">
<title>Public Functions Provided</title>
-!Edrivers/media/video/videodev.c
+!Edrivers/media/video/v4l2-dev.c
</chapter>
</book>
device to be used as both a tty interface and as a synchronous
controller is a project for Linux post the 2.4 release
</para>
- <para>
- The support code handles most common card configurations and
- supports running both Cisco HDLC and Synchronous PPP. With extra
- glue the frame relay and X.25 protocols can also be used with this
- driver.
- </para>
</chapter>
<chapter id="Driver_Modes">
<para>
If you wish to use the network interface facilities of the driver,
then you need to attach a network device to each channel that is
- present and in use. In addition to use the SyncPPP and Cisco HDLC
+ present and in use. In addition to use the generic HDLC
you need to follow some additional plumbing rules. They may seem
complex but a look at the example hostess_sv11 driver should
reassure you.
</para>
<para>
The network device used for each channel should be pointed to by
- the netdevice field of each channel. The dev-> priv field of the
+ the netdevice field of each channel. The hdlc-> priv field of the
network device points to your private data - you will need to be
- able to find your ppp device from this. In addition to use the
- sync ppp layer the private data must start with a void * pointer
- to the syncppp structures.
+ able to find your private data from this.
</para>
<para>
The way most drivers approach this particular problem is to
create a structure holding the Z8530 device definition and
- put that and the syncppp pointer into the private field of
- the network device. The network device fields of the channels
- then point back to the network devices. The ppp_device can also
- be put in the private structure conveniently.
+ put that into the private field of the network device. The
+ network device fields of the channels then point back to the
+ network devices.
</para>
<para>
- If you wish to use the synchronous ppp then you need to attach
- the syncppp layer to the network device. You should do this before
- you register the network device. The
- <function>sppp_attach</function> requires that the first void *
- pointer in your private data is pointing to an empty struct
- ppp_device. The function fills in the initial data for the
- ppp/hdlc layer.
+ If you wish to use the generic HDLC then you need to register
+ the HDLC device.
</para>
<para>
Before you register your network device you will also need to
buffer in sk_buff format and queues it for transmission. The
caller must provide the entire packet with the exception of the
bitstuffing and CRC. This is normally done by the caller via
- the syncppp interface layer. It returns 0 if the buffer has been
- queued and non zero values for queue full. If the function accepts
- the buffer it becomes property of the Z8530 layer and the caller
- should not free it.
+ the generic HDLC interface layer. It returns 0 if the buffer has been
+ queued and non zero values for queue full. If the function accepts
+ the buffer it becomes property of the Z8530 layer and the caller
+ should not free it.
</para>
<para>
The function <function>z8530_get_stats</function> returns a pointer
- Flash access (MTD/JFFS)
- I2C through GPIO on IXP42x
- GPIO for input/output/interrupts
- See include/asm-arm/arch-ixp4xx/platform.h for access functions.
+ See arch/arm/mach-ixp4xx/include/mach/platform.h for access functions.
- Timers (watchdog, OS)
The following components of the chips are not supported by Linux and
be re-checked for pending events. (see the Neponset IRQ handler for
details).
-7. fixup_irq() is gone, as is include/asm-arm/arch-*/irq.h
+7. fixup_irq() is gone, as is arch/arm/mach-*/include/mach/irq.h
Please note that this will not solve all problems - some of them are
hardware based. Mixing level-based and edge-based IRQs on the same
To this end, we now have arch/arm/mach-$(MACHINE) directories which are
designed to house the non-driver files for a particular machine (eg, PCI,
memory management, architecture definitions etc). For all future
- machines, there should be a corresponding include/asm-arm/arch-$(MACHINE)
+ machines, there should be a corresponding arch/arm/mach-$(MACHINE)/include/mach
directory.
class typically based around one or more system on a chip devices, and
acts as a natural container around the actual implementations. These
classes are given directories - arch/arm/mach-<class> and
- include/asm-arm/arch-<class> - which contain the source files to
+ arch/arm/mach-<class> - which contain the source files to/include/mach
support the machine class. This directories also contain any machine
specific supporting code.
Headers
-------
- See include/asm-arm/arch-s3c2410/regs-gpio.h for the list
+ See arch/arm/mach-s3c2410/include/mach/regs-gpio.h for the list
of GPIO pins, and the configuration values for them. This
- is included by using #include <asm/arch/regs-gpio.h>
+ is included by using #include <mach/regs-gpio.h>
The GPIO management functions are defined in the hardware
- header include/asm-arm/arch-s3c2410/hardware.h which can be
- included by #include <asm/arch/hardware.h>
+ header arch/arm/mach-s3c2410/include/mach/hardware.h which can be
+ included by #include <mach/hardware.h>
A useful amount of documentation can be found in the hardware
header on how the GPIO functions (and others) work.
in arch/arm/mach-s3c2410 and S3C2440 in arch/arm/mach-s3c2440
Register, kernel and platform data definitions are held in the
- include/asm-arm/arch-s3c2410 directory.
+ arch/arm/mach-s3c2410 directory./include/mach
Machines
Platform Data
-------------
- See linux/include/asm-arm/arch-s3c2410/usb-control.h for the
+ See arch/arm/mach-s3c2410/include/mach/usb-control.h for the
descriptions of the platform device data. An implementation
can be found in linux/arch/arm/mach-s3c2410/usb-simtec.c .
Hot plugging of SCSI tape drives is supported, with some caveats.
The cciss driver must be informed that changes to the SCSI bus
-have been made, in addition to and prior to informing the SCSI
-mid layer. This may be done via the /proc filesystem. For example:
+have been made. This may be done via the /proc filesystem.
+For example:
echo "rescan" > /proc/scsi/cciss0/1
-This causes the adapter to query the adapter about changes to the
-physical SCSI buses and/or fibre channel arbitrated loop and the
+This causes the driver to query the adapter about changes to the
+physical SCSI buses and/or fibre channel arbitrated loop and the
driver to make note of any new or removed sequential access devices
or medium changers. The driver will output messages indicating what
devices have been added or removed and the controller, bus, target and
-lun used to address the device. Once this is done, the SCSI mid layer
-can be informed of changes to the virtual SCSI bus which the driver
-presents to it in the usual way. For example:
-
- echo scsi add-single-device 3 2 1 0 > /proc/scsi/scsi
-
-to add a device on controller 3, bus 2, target 1, lun 0. Note that
-the driver makes an effort to preserve the devices positions
-in the virtual SCSI bus, so if you are only moving tape drives
-around on the same adapter and not adding or removing tape drives
-from the adapter, informing the SCSI mid layer may not be necessary.
+lun used to address the device. It then notifies the SCSI mid layer
+of these changes.
Note that the naming convention of the /proc filesystem entries
contains a number in addition to the driver name. (E.g. "cciss0"
+++ /dev/null
-
-#### cli()/sti() removal guide, started by Ingo Molnar <mingo@redhat.com>
-
-
-as of 2.5.28, five popular macros have been removed on SMP, and
-are being phased out on UP:
-
- cli(), sti(), save_flags(flags), save_flags_cli(flags), restore_flags(flags)
-
-until now it was possible to protect driver code against interrupt
-handlers via a cli(), but from now on other, more lightweight methods
-have to be used for synchronization, such as spinlocks or semaphores.
-
-for example, driver code that used to do something like:
-
- struct driver_data;
-
- irq_handler (...)
- {
- ....
- driver_data.finish = 1;
- driver_data.new_work = 0;
- ....
- }
-
- ...
-
- ioctl_func (...)
- {
- ...
- cli();
- ...
- driver_data.finish = 0;
- driver_data.new_work = 2;
- ...
- sti();
- ...
- }
-
-was SMP-correct because the cli() function ensured that no
-interrupt handler (amongst them the above irq_handler()) function
-would execute while the cli()-ed section is executing.
-
-but from now on a more direct method of locking has to be used:
-
- DEFINE_SPINLOCK(driver_lock);
- struct driver_data;
-
- irq_handler (...)
- {
- unsigned long flags;
- ....
- spin_lock_irqsave(&driver_lock, flags);
- ....
- driver_data.finish = 1;
- driver_data.new_work = 0;
- ....
- spin_unlock_irqrestore(&driver_lock, flags);
- ....
- }
-
- ...
-
- ioctl_func (...)
- {
- ...
- spin_lock_irq(&driver_lock);
- ...
- driver_data.finish = 0;
- driver_data.new_work = 2;
- ...
- spin_unlock_irq(&driver_lock);
- ...
- }
-
-the above code has a number of advantages:
-
-- the locking relation is easier to understand - actual lock usage
- pinpoints the critical sections. cli() usage is too opaque.
- Easier to understand means it's easier to debug.
-
-- it's faster, because spinlocks are faster to acquire than the
- potentially heavily-used IRQ lock. Furthermore, your driver does
- not have to wait eg. for a big heavy SCSI interrupt to finish,
- because the driver_lock spinlock is only used by your driver.
- cli() on the other hand was used by many drivers, and extended
- the critical section to the whole IRQ handler function - creating
- serious lock contention.
-
-
-to make the transition easier, we've still kept the cli(), sti(),
-save_flags(), save_flags_cli() and restore_flags() macros defined
-on UP systems - but their usage will be phased out until 2.6 is
-released.
-
-drivers that want to disable local interrupts (interrupts on the
-current CPU), can use the following five macros:
-
- local_irq_disable(), local_irq_enable(), local_save_flags(flags),
- local_irq_save(flags), local_irq_restore(flags)
-
-but beware, their meaning and semantics are much simpler, far from
-that of the old cli(), sti(), save_flags(flags) and restore_flags(flags)
-SMP meaning:
-
- local_irq_disable() => turn local IRQs off
-
- local_irq_enable() => turn local IRQs on
-
- local_save_flags(flags) => save the current IRQ state into flags. The
- state can be on or off. (on some
- architectures there's even more bits in it.)
-
- local_irq_save(flags) => save the current IRQ state into flags and
- disable interrupts.
-
- local_irq_restore(flags) => restore the IRQ state from flags.
-
-(local_irq_save can save both irqs on and irqs off state, and
-local_irq_restore can restore into both irqs on and irqs off state.)
-
-another related change is that synchronize_irq() now takes a parameter:
-synchronize_irq(irq). This change too has the purpose of making SMP
-synchronization more lightweight - this way you can wait for your own
-interrupt handler to finish, no need to wait for other IRQ sources.
-
-
-why were these changes done? The main reason was the architectural burden
-of maintaining the cli()/sti() interface - it became a real problem. The
-new interrupt system is much more streamlined, easier to understand, debug,
-and it's also a bit faster - the same happened to it that will happen to
-cli()/sti() using drivers once they convert to spinlocks :-)
-
[An Example]
The best example of these basic concepts is the simple_children
-subsystem/group and the simple_child item in configfs_example.c It
-shows a trivial object displaying and storing an attribute, and a simple
-group creating and destroying these children.
+subsystem/group and the simple_child item in configfs_example_explicit.c
+and configfs_example_macros.c. It shows a trivial object displaying and
+storing an attribute, and a simple group creating and destroying these
+children.
+
+The only difference between configfs_example_explicit.c and
+configfs_example_macros.c is how the attributes of the childless item
+are defined. The childless item has extended attributes, each with
+their own show()/store() operation. This follows a convention commonly
+used in sysfs. configfs_example_explicit.c creates these attributes
+by explicitly defining the structures involved. Conversely
+configfs_example_macros.c uses some convenience macros from configfs.h
+to define the attributes. These macros are similar to their sysfs
+counterparts.
[Hierarchy Navigation and the Subsystem Mutex]
/*
* vim: noexpandtab ts=8 sts=0 sw=8:
*
- * configfs_example.c - This file is a demonstration module containing
- * a number of configfs subsystems.
+ * configfs_example_explicit.c - This file is a demonstration module
+ * containing a number of configfs subsystems. It explicitly defines
+ * each structure without using the helper macros defined in
+ * configfs.h.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public
if (!simple_child)
return ERR_PTR(-ENOMEM);
-
config_item_init_type_name(&simple_child->item, name,
&simple_child_type);
};
static ssize_t simple_children_attr_show(struct config_item *item,
- struct configfs_attribute *attr,
- char *page)
+ struct configfs_attribute *attr,
+ char *page)
{
return sprintf(page,
"[02-simple-children]\n"
}
static struct configfs_item_operations simple_children_item_ops = {
- .release = simple_children_release,
+ .release = simple_children_release,
.show_attribute = simple_children_attr_show,
};
if (!simple_children)
return ERR_PTR(-ENOMEM);
-
config_group_init_type_name(&simple_children->group, name,
&simple_children_type);
};
static ssize_t group_children_attr_show(struct config_item *item,
- struct configfs_attribute *attr,
- char *page)
+ struct configfs_attribute *attr,
+ char *page)
{
return sprintf(page,
"[03-group-children]\n"
--- /dev/null
+/*
+ * vim: noexpandtab ts=8 sts=0 sw=8:
+ *
+ * configfs_example_macros.c - This file is a demonstration module
+ * containing a number of configfs subsystems. It uses the helper
+ * macros defined by configfs.h
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this program; if not, write to the
+ * Free Software Foundation, Inc., 59 Temple Place - Suite 330,
+ * Boston, MA 021110-1307, USA.
+ *
+ * Based on sysfs:
+ * sysfs is Copyright (C) 2001, 2002, 2003 Patrick Mochel
+ *
+ * configfs Copyright (C) 2005 Oracle. All rights reserved.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#include <linux/configfs.h>
+
+
+
+/*
+ * 01-childless
+ *
+ * This first example is a childless subsystem. It cannot create
+ * any config_items. It just has attributes.
+ *
+ * Note that we are enclosing the configfs_subsystem inside a container.
+ * This is not necessary if a subsystem has no attributes directly
+ * on the subsystem. See the next example, 02-simple-children, for
+ * such a subsystem.
+ */
+
+struct childless {
+ struct configfs_subsystem subsys;
+ int showme;
+ int storeme;
+};
+
+static inline struct childless *to_childless(struct config_item *item)
+{
+ return item ? container_of(to_configfs_subsystem(to_config_group(item)), struct childless, subsys) : NULL;
+}
+
+CONFIGFS_ATTR_STRUCT(childless);
+#define CHILDLESS_ATTR(_name, _mode, _show, _store) \
+struct childless_attribute childless_attr_##_name = __CONFIGFS_ATTR(_name, _mode, _show, _store)
+#define CHILDLESS_ATTR_RO(_name, _show) \
+struct childless_attribute childless_attr_##_name = __CONFIGFS_ATTR_RO(_name, _show);
+
+static ssize_t childless_showme_read(struct childless *childless,
+ char *page)
+{
+ ssize_t pos;
+
+ pos = sprintf(page, "%d\n", childless->showme);
+ childless->showme++;
+
+ return pos;
+}
+
+static ssize_t childless_storeme_read(struct childless *childless,
+ char *page)
+{
+ return sprintf(page, "%d\n", childless->storeme);
+}
+
+static ssize_t childless_storeme_write(struct childless *childless,
+ const char *page,
+ size_t count)
+{
+ unsigned long tmp;
+ char *p = (char *) page;
+
+ tmp = simple_strtoul(p, &p, 10);
+ if (!p || (*p && (*p != '\n')))
+ return -EINVAL;
+
+ if (tmp > INT_MAX)
+ return -ERANGE;
+
+ childless->storeme = tmp;
+
+ return count;
+}
+
+static ssize_t childless_description_read(struct childless *childless,
+ char *page)
+{
+ return sprintf(page,
+"[01-childless]\n"
+"\n"
+"The childless subsystem is the simplest possible subsystem in\n"
+"configfs. It does not support the creation of child config_items.\n"
+"It only has a few attributes. In fact, it isn't much different\n"
+"than a directory in /proc.\n");
+}
+
+CHILDLESS_ATTR_RO(showme, childless_showme_read);
+CHILDLESS_ATTR(storeme, S_IRUGO | S_IWUSR, childless_storeme_read,
+ childless_storeme_write);
+CHILDLESS_ATTR_RO(description, childless_description_read);
+
+static struct configfs_attribute *childless_attrs[] = {
+ &childless_attr_showme.attr,
+ &childless_attr_storeme.attr,
+ &childless_attr_description.attr,
+ NULL,
+};
+
+CONFIGFS_ATTR_OPS(childless);
+static struct configfs_item_operations childless_item_ops = {
+ .show_attribute = childless_attr_show,
+ .store_attribute = childless_attr_store,
+};
+
+static struct config_item_type childless_type = {
+ .ct_item_ops = &childless_item_ops,
+ .ct_attrs = childless_attrs,
+ .ct_owner = THIS_MODULE,
+};
+
+static struct childless childless_subsys = {
+ .subsys = {
+ .su_group = {
+ .cg_item = {
+ .ci_namebuf = "01-childless",
+ .ci_type = &childless_type,
+ },
+ },
+ },
+};
+
+
+/* ----------------------------------------------------------------- */
+
+/*
+ * 02-simple-children
+ *
+ * This example merely has a simple one-attribute child. Note that
+ * there is no extra attribute structure, as the child's attribute is
+ * known from the get-go. Also, there is no container for the
+ * subsystem, as it has no attributes of its own.
+ */
+
+struct simple_child {
+ struct config_item item;
+ int storeme;
+};
+
+static inline struct simple_child *to_simple_child(struct config_item *item)
+{
+ return item ? container_of(item, struct simple_child, item) : NULL;
+}
+
+static struct configfs_attribute simple_child_attr_storeme = {
+ .ca_owner = THIS_MODULE,
+ .ca_name = "storeme",
+ .ca_mode = S_IRUGO | S_IWUSR,
+};
+
+static struct configfs_attribute *simple_child_attrs[] = {
+ &simple_child_attr_storeme,
+ NULL,
+};
+
+static ssize_t simple_child_attr_show(struct config_item *item,
+ struct configfs_attribute *attr,
+ char *page)
+{
+ ssize_t count;
+ struct simple_child *simple_child = to_simple_child(item);
+
+ count = sprintf(page, "%d\n", simple_child->storeme);
+
+ return count;
+}
+
+static ssize_t simple_child_attr_store(struct config_item *item,
+ struct configfs_attribute *attr,
+ const char *page, size_t count)
+{
+ struct simple_child *simple_child = to_simple_child(item);
+ unsigned long tmp;
+ char *p = (char *) page;
+
+ tmp = simple_strtoul(p, &p, 10);
+ if (!p || (*p && (*p != '\n')))
+ return -EINVAL;
+
+ if (tmp > INT_MAX)
+ return -ERANGE;
+
+ simple_child->storeme = tmp;
+
+ return count;
+}
+
+static void simple_child_release(struct config_item *item)
+{
+ kfree(to_simple_child(item));
+}
+
+static struct configfs_item_operations simple_child_item_ops = {
+ .release = simple_child_release,
+ .show_attribute = simple_child_attr_show,
+ .store_attribute = simple_child_attr_store,
+};
+
+static struct config_item_type simple_child_type = {
+ .ct_item_ops = &simple_child_item_ops,
+ .ct_attrs = simple_child_attrs,
+ .ct_owner = THIS_MODULE,
+};
+
+
+struct simple_children {
+ struct config_group group;
+};
+
+static inline struct simple_children *to_simple_children(struct config_item *item)
+{
+ return item ? container_of(to_config_group(item), struct simple_children, group) : NULL;
+}
+
+static struct config_item *simple_children_make_item(struct config_group *group, const char *name)
+{
+ struct simple_child *simple_child;
+
+ simple_child = kzalloc(sizeof(struct simple_child), GFP_KERNEL);
+ if (!simple_child)
+ return ERR_PTR(-ENOMEM);
+
+ config_item_init_type_name(&simple_child->item, name,
+ &simple_child_type);
+
+ simple_child->storeme = 0;
+
+ return &simple_child->item;
+}
+
+static struct configfs_attribute simple_children_attr_description = {
+ .ca_owner = THIS_MODULE,
+ .ca_name = "description",
+ .ca_mode = S_IRUGO,
+};
+
+static struct configfs_attribute *simple_children_attrs[] = {
+ &simple_children_attr_description,
+ NULL,
+};
+
+static ssize_t simple_children_attr_show(struct config_item *item,
+ struct configfs_attribute *attr,
+ char *page)
+{
+ return sprintf(page,
+"[02-simple-children]\n"
+"\n"
+"This subsystem allows the creation of child config_items. These\n"
+"items have only one attribute that is readable and writeable.\n");
+}
+
+static void simple_children_release(struct config_item *item)
+{
+ kfree(to_simple_children(item));
+}
+
+static struct configfs_item_operations simple_children_item_ops = {
+ .release = simple_children_release,
+ .show_attribute = simple_children_attr_show,
+};
+
+/*
+ * Note that, since no extra work is required on ->drop_item(),
+ * no ->drop_item() is provided.
+ */
+static struct configfs_group_operations simple_children_group_ops = {
+ .make_item = simple_children_make_item,
+};
+
+static struct config_item_type simple_children_type = {
+ .ct_item_ops = &simple_children_item_ops,
+ .ct_group_ops = &simple_children_group_ops,
+ .ct_attrs = simple_children_attrs,
+ .ct_owner = THIS_MODULE,
+};
+
+static struct configfs_subsystem simple_children_subsys = {
+ .su_group = {
+ .cg_item = {
+ .ci_namebuf = "02-simple-children",
+ .ci_type = &simple_children_type,
+ },
+ },
+};
+
+
+/* ----------------------------------------------------------------- */
+
+/*
+ * 03-group-children
+ *
+ * This example reuses the simple_children group from above. However,
+ * the simple_children group is not the subsystem itself, it is a
+ * child of the subsystem. Creation of a group in the subsystem creates
+ * a new simple_children group. That group can then have simple_child
+ * children of its own.
+ */
+
+static struct config_group *group_children_make_group(struct config_group *group, const char *name)
+{
+ struct simple_children *simple_children;
+
+ simple_children = kzalloc(sizeof(struct simple_children),
+ GFP_KERNEL);
+ if (!simple_children)
+ return ERR_PTR(-ENOMEM);
+
+ config_group_init_type_name(&simple_children->group, name,
+ &simple_children_type);
+
+ return &simple_children->group;
+}
+
+static struct configfs_attribute group_children_attr_description = {
+ .ca_owner = THIS_MODULE,
+ .ca_name = "description",
+ .ca_mode = S_IRUGO,
+};
+
+static struct configfs_attribute *group_children_attrs[] = {
+ &group_children_attr_description,
+ NULL,
+};
+
+static ssize_t group_children_attr_show(struct config_item *item,
+ struct configfs_attribute *attr,
+ char *page)
+{
+ return sprintf(page,
+"[03-group-children]\n"
+"\n"
+"This subsystem allows the creation of child config_groups. These\n"
+"groups are like the subsystem simple-children.\n");
+}
+
+static struct configfs_item_operations group_children_item_ops = {
+ .show_attribute = group_children_attr_show,
+};
+
+/*
+ * Note that, since no extra work is required on ->drop_item(),
+ * no ->drop_item() is provided.
+ */
+static struct configfs_group_operations group_children_group_ops = {
+ .make_group = group_children_make_group,
+};
+
+static struct config_item_type group_children_type = {
+ .ct_item_ops = &group_children_item_ops,
+ .ct_group_ops = &group_children_group_ops,
+ .ct_attrs = group_children_attrs,
+ .ct_owner = THIS_MODULE,
+};
+
+static struct configfs_subsystem group_children_subsys = {
+ .su_group = {
+ .cg_item = {
+ .ci_namebuf = "03-group-children",
+ .ci_type = &group_children_type,
+ },
+ },
+};
+
+/* ----------------------------------------------------------------- */
+
+/*
+ * We're now done with our subsystem definitions.
+ * For convenience in this module, here's a list of them all. It
+ * allows the init function to easily register them. Most modules
+ * will only have one subsystem, and will only call register_subsystem
+ * on it directly.
+ */
+static struct configfs_subsystem *example_subsys[] = {
+ &childless_subsys.subsys,
+ &simple_children_subsys,
+ &group_children_subsys,
+ NULL,
+};
+
+static int __init configfs_example_init(void)
+{
+ int ret;
+ int i;
+ struct configfs_subsystem *subsys;
+
+ for (i = 0; example_subsys[i]; i++) {
+ subsys = example_subsys[i];
+
+ config_group_init(&subsys->su_group);
+ mutex_init(&subsys->su_mutex);
+ ret = configfs_register_subsystem(subsys);
+ if (ret) {
+ printk(KERN_ERR "Error %d while registering subsystem %s\n",
+ ret,
+ subsys->su_group.cg_item.ci_namebuf);
+ goto out_unregister;
+ }
+ }
+
+ return 0;
+
+out_unregister:
+ for (; i >= 0; i--) {
+ configfs_unregister_subsystem(example_subsys[i]);
+ }
+
+ return ret;
+}
+
+static void __exit configfs_example_exit(void)
+{
+ int i;
+
+ for (i = 0; example_subsys[i]; i++) {
+ configfs_unregister_subsystem(example_subsys[i]);
+ }
+}
+
+module_init(configfs_example_init);
+module_exit(configfs_example_exit);
+MODULE_LICENSE("GPL");
Copyright 2008 Red Hat Inc.
Author: Steven Rostedt <srostedt@redhat.com>
License: The GNU Free Documentation License, Version 1.2
+ (dual licensed under the GPL v2)
Reviewers: Elias Oltmanns, Randy Dunlap, Andrew Morton,
John Kacur, and David Teigland.
Prefix: 'sch311x'
Addresses scanned: none, address read from Super-I/O config space
Datasheet: http://www.nuhorizons.com/FeaturedProducts/Volume1/SMSC/311x.pdf
+ * SMSC SCH5027
+ Prefix: 'sch5027'
+ Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+ Datasheet: Provided by SMSC upon request and under NDA
Authors:
Juerg Haefliger <juergh@gmail.com>
and PWM output control functions. Using this parameter
shouldn't be required since the BIOS usually takes care
of this.
-
-Note that there is no need to use this parameter if the driver loads without
-complaining. The driver will say so if it is necessary.
+* probe_all_addr: bool Include non-standard LPC addresses 0x162e and 0x164e
+ when probing for ISA devices. This is required for the
+ following boards:
+ - VIA EPIA SN18000
Description
-----------
This driver implements support for the hardware monitoring capabilities of the
-SMSC DME1737 and Asus A8000 (which are the same) and SMSC SCH311x Super-I/O
-chips. These chips feature monitoring of 3 temp sensors temp[1-3] (2 remote
-diodes and 1 internal), 7 voltages in[0-6] (6 external and 1 internal) and up
-to 6 fan speeds fan[1-6]. Additionally, the chips implement up to 5 PWM
-outputs pwm[1-3,5-6] for controlling fan speeds both manually and
+SMSC DME1737 and Asus A8000 (which are the same), SMSC SCH5027, and SMSC
+SCH311x Super-I/O chips. These chips feature monitoring of 3 temp sensors
+temp[1-3] (2 remote diodes and 1 internal), 7 voltages in[0-6] (6 external and
+1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement
+up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and
automatically.
-For the DME1737 and A8000, fan[1-2] and pwm[1-2] are always present. Fan[3-6]
-and pwm[3,5-6] are optional features and their availability depends on the
-configuration of the chip. The driver will detect which features are present
-during initialization and create the sysfs attributes accordingly.
+For the DME1737, A8000 and SCH5027, fan[1-2] and pwm[1-2] are always present.
+Fan[3-6] and pwm[3,5-6] are optional features and their availability depends on
+the configuration of the chip. The driver will detect which features are
+present during initialization and create the sysfs attributes accordingly.
For the SCH311x, fan[1-3] and pwm[1-3] are always present and fan[4-6] and
pwm[5-6] don't exist.
-The hardware monitoring features of the DME1737 and A8000 are only accessible
-via SMBus, while the SCH311x only provides access via the ISA bus. The driver
-will therefore register itself as an I2C client driver if it detects a DME1737
-or A8000 and as a platform driver if it detects a SCH311x chip.
+The hardware monitoring features of the DME1737, A8000, and SCH5027 are only
+accessible via SMBus, while the SCH311x only provides access via the ISA bus.
+The driver will therefore register itself as an I2C client driver if it detects
+a DME1737, A8000, or SCH5027 and as a platform driver if it detects a SCH311x
+chip.
Voltage Monitoring
millivolts and don't need scaling. The voltage inputs are mapped as follows
(the last column indicates the input ranges):
+DME1737, A8000:
in0: +5VTR (+5V standby) 0V - 6.64V
in1: Vccp (processor core) 0V - 3V
in2: VCC (internal +3.3V) 0V - 4.38V
in5: VTR (+3.3V standby) 0V - 4.38V
in6: Vbat (+3.0V) 0V - 4.38V
+SCH311x:
+ in0: +2.5V 0V - 6.64V
+ in1: Vccp (processor core) 0V - 2V
+ in2: VCC (internal +3.3V) 0V - 4.38V
+ in3: +5V 0V - 6.64V
+ in4: +12V 0V - 16V
+ in5: VTR (+3.3V standby) 0V - 4.38V
+ in6: Vbat (+3.0V) 0V - 4.38V
+
+SCH5027:
+ in0: +5VTR (+5V standby) 0V - 6.64V
+ in1: Vccp (processor core) 0V - 3V
+ in2: VCC (internal +3.3V) 0V - 4.38V
+ in3: V2_IN 0V - 1.5V
+ in4: V1_IN 0V - 1.5V
+ in5: VTR (+3.3V standby) 0V - 4.38V
+ in6: Vbat (+3.0V) 0V - 4.38V
+
Each voltage input has associated min and max limits which trigger an alarm
when crossed.
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
- http://www.ite.com.tw/
+ http://www.ite.com.tw/product_info/file/pc/IT8705F_V.0.4.1.pdf
* IT8712F
Prefix: 'it8712'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Publicly available at the ITE website
- http://www.ite.com.tw/
+ http://www.ite.com.tw/product_info/file/pc/IT8712F_V0.9.1.pdf
+ http://www.ite.com.tw/product_info/file/pc/Errata%20V0.1%20for%20IT8712F%20V0.9.1.pdf
+ http://www.ite.com.tw/product_info/file/pc/IT8712F_V0.9.3.pdf
* IT8716F/IT8726F
Prefix: 'it8716'
Addresses scanned: from Super I/O config space (8 I/O ports)
can't have both on a given board.
The IT8716F, IT8718F and later IT8712F revisions have support for
-2 additional fans. They are supported by the driver for the IT8716F and
-IT8718F but not for the IT8712F
+2 additional fans. The additional fans are supported by the driver.
The IT8716F and IT8718F, and late IT8712F and IT8705F also have optional
16-bit tachometer counters for fans 1 to 3. This is better (no more fan
clock divider mess) but not compatible with the older chips and
-revisions. For now, the driver only uses the 16-bit mode on the
-IT8716F and IT8718F.
+revisions. The 16-bit tachometer mode is enabled by the driver when one
+of the above chips is detected.
The IT8726F is just bit enhanced IT8716F with additional hardware
for AMD power sequencing. Therefore the chip will appear as IT8716F
confirmed this "bug". The ADT7463 is reported to work as described in the
documentation. The current lm85 driver does not show the offset register.
-The ADT7463 has a THERM asserted counter. This counter has a 22.76ms
-resolution and a range of 5.8 seconds. The driver implements a 32-bit
-accumulator of the counter value to extend the range to over a year. The
-counter will stay at it's max value until read.
-
See the vendor datasheets for more information. There is application note
from National (AN-1260) with some additional information about the LM85.
The Analog Devices datasheet is very detailed and describes a procedure for
The National LM85's have two vendor specific configuration
features. Tach. mode and Spinup Control. For more details on these,
-see the LM85 datasheet or Application Note AN-1260.
+see the LM85 datasheet or Application Note AN-1260. These features
+are not currently supported by the lm85 driver.
The Analog Devices ADM1027 has several vendor specific enhancements.
The number of pulses-per-rev of the fans can be set, Tach monitoring
can be optimized for PWM operation, and an offset can be applied to
the temperatures to compensate for systemic errors in the
-measurements.
+measurements. These features are not currently supported by the lm85
+driver.
In addition to the ADM1027 features, the ADT7463 also has Tmin control
and THERM asserted counts. Automatic Tmin control acts to adjust the
(default is 1)
Use 'init=0' to bypass initializing the chip.
Try this if your computer crashes when you load the module.
-* reset: int
- (default is 0)
- The driver used to reset the chip on load, but does no more. Use
- 'reset=1' to restore the old behavior. Report if you need to do this.
Description
-----------
Additional contributors:
Sven Anders <anders@anduras.de>
+ Marc Hulsman <m.hulsman@tudelft.nl>
Module Parameters
-----------------
Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
triggered if the rotation speed has dropped below a programmable limit. Fan
-readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3
-and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more
-range or accuracy.
+readings can be divided by a programmable divider (1, 2, 4, 8, 16,
+32, 64 or 128 for all fans) to give the readings more range or accuracy.
Voltage sensors (also known as IN sensors) report their values in millivolts.
An alarm is triggered if the voltage has crossed a programmable minimum
-PM quality of Service interface.
+PM Quality Of Service Interface.
This interface provides a kernel and user mode interface for registering
performance expectations by drivers, subsystems and user space applications on
Currently we have {cpu_dma_latency, network_latency, network_throughput} as the
initial set of pm_qos parameters.
+Each parameters have defined units:
+ * latency: usec
+ * timeout: usec
+ * throughput: kbs (kilo bit / sec)
+
The infrastructure exposes multiple misc device nodes one per implemented
parameter. The set of parameters implement is defined by pm_qos_power_init()
and pm_qos_params.h. This is done because having the available parameters
charge when battery considered full/empty at given conditions (temperature,
age)". I.e. these attributes represents real thresholds, not design values.
+CHARGE_COUNTER - the current charge counter (in µAh). This could easily
+be negative; there is no empty or full value. It is only useful for
+relative, time-based measurements.
+
ENERGY_FULL, ENERGY_EMPTY - same as above but for energy.
CAPACITY - capacity in percents.
--- /dev/null
+Regulator Consumer Driver Interface
+===================================
+
+This text describes the regulator interface for consumer device drivers.
+Please see overview.txt for a description of the terms used in this text.
+
+
+1. Consumer Regulator Access (static & dynamic drivers)
+=======================================================
+
+A consumer driver can get access to it's supply regulator by calling :-
+
+regulator = regulator_get(dev, "Vcc");
+
+The consumer passes in it's struct device pointer and power supply ID. The core
+then finds the correct regulator by consulting a machine specific lookup table.
+If the lookup is successful then this call will return a pointer to the struct
+regulator that supplies this consumer.
+
+To release the regulator the consumer driver should call :-
+
+regulator_put(regulator);
+
+Consumers can be supplied by more than one regulator e.g. codec consumer with
+analog and digital supplies :-
+
+digital = regulator_get(dev, "Vcc"); /* digital core */
+analog = regulator_get(dev, "Avdd"); /* analog */
+
+The regulator access functions regulator_get() and regulator_put() will
+usually be called in your device drivers probe() and remove() respectively.
+
+
+2. Regulator Output Enable & Disable (static & dynamic drivers)
+====================================================================
+
+A consumer can enable it's power supply by calling:-
+
+int regulator_enable(regulator);
+
+NOTE: The supply may already be enabled before regulator_enabled() is called.
+This may happen if the consumer shares the regulator or the regulator has been
+previously enabled by bootloader or kernel board initialization code.
+
+A consumer can determine if a regulator is enabled by calling :-
+
+int regulator_is_enabled(regulator);
+
+This will return > zero when the regulator is enabled.
+
+
+A consumer can disable it's supply when no longer needed by calling :-
+
+int regulator_disable(regulator);
+
+NOTE: This may not disable the supply if it's shared with other consumers. The
+regulator will only be disabled when the enabled reference count is zero.
+
+Finally, a regulator can be forcefully disabled in the case of an emergency :-
+
+int regulator_force_disable(regulator);
+
+NOTE: this will immediately and forcefully shutdown the regulator output. All
+consumers will be powered off.
+
+
+3. Regulator Voltage Control & Status (dynamic drivers)
+======================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+voltage to match system operating points. e.g. CPUfreq drivers can scale
+voltage along with frequency to save power, SD drivers may need to select the
+correct card voltage, etc.
+
+Consumers can control their supply voltage by calling :-
+
+int regulator_set_voltage(regulator, min_uV, max_uV);
+
+Where min_uV and max_uV are the minimum and maximum acceptable voltages in
+microvolts.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the voltage changes instantly, otherwise the voltage
+configuration changes and the voltage is physically set when the regulator is
+next enabled.
+
+The regulators configured voltage output can be found by calling :-
+
+int regulator_get_voltage(regulator);
+
+NOTE: get_voltage() will return the configured output voltage whether the
+regulator is enabled or disabled and should NOT be used to determine regulator
+output state. However this can be used in conjunction with is_enabled() to
+determine the regulator physical output voltage.
+
+
+4. Regulator Current Limit Control & Status (dynamic drivers)
+===========================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+current limit to match system operating points. e.g. LCD backlight driver can
+change the current limit to vary the backlight brightness, USB drivers may want
+to set the limit to 500mA when supplying power.
+
+Consumers can control their supply current limit by calling :-
+
+int regulator_set_current_limit(regulator, min_uV, max_uV);
+
+Where min_uA and max_uA are the minimum and maximum acceptable current limit in
+microamps.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the current limit changes instantly, otherwise the current
+limit configuration changes and the current limit is physically set when the
+regulator is next enabled.
+
+A regulators current limit can be found by calling :-
+
+int regulator_get_current_limit(regulator);
+
+NOTE: get_current_limit() will return the current limit whether the regulator
+is enabled or disabled and should not be used to determine regulator current
+load.
+
+
+5. Regulator Operating Mode Control & Status (dynamic drivers)
+=============================================================
+
+Some consumers can further save system power by changing the operating mode of
+their supply regulator to be more efficient when the consumers operating state
+changes. e.g. consumer driver is idle and subsequently draws less current
+
+Regulator operating mode can be changed indirectly or directly.
+
+Indirect operating mode control.
+--------------------------------
+Consumer drivers can request a change in their supply regulator operating mode
+by calling :-
+
+int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);
+
+This will cause the core to recalculate the total load on the regulator (based
+on all it's consumers) and change operating mode (if necessary and permitted)
+to best match the current operating load.
+
+The load_uA value can be determined from the consumers datasheet. e.g.most
+datasheets have tables showing the max current consumed in certain situations.
+
+Most consumers will use indirect operating mode control since they have no
+knowledge of the regulator or whether the regulator is shared with other
+consumers.
+
+Direct operating mode control.
+------------------------------
+Bespoke or tightly coupled drivers may want to directly control regulator
+operating mode depending on their operating point. This can be achieved by
+calling :-
+
+int regulator_set_mode(struct regulator *regulator, unsigned int mode);
+unsigned int regulator_get_mode(struct regulator *regulator);
+
+Direct mode will only be used by consumers that *know* about the regulator and
+are not sharing the regulator with other consumers.
+
+
+6. Regulator Events
+===================
+Regulators can notify consumers of external events. Events could be received by
+consumers under regulator stress or failure conditions.
+
+Consumers can register interest in regulator events by calling :-
+
+int regulator_register_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+
+Consumers can uregister interest by calling :-
+
+int regulator_unregister_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+
+Regulators use the kernel notifier framework to send event to thier interested
+consumers.
--- /dev/null
+Regulator Machine Driver Interface
+===================================
+
+The regulator machine driver interface is intended for board/machine specific
+initialisation code to configure the regulator subsystem. Typical things that
+machine drivers would do are :-
+
+ 1. Regulator -> Device mapping.
+ 2. Regulator supply configuration.
+ 3. Power Domain constraint setting.
+
+
+
+1. Regulator -> device mapping
+==============================
+Consider the following machine :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+The drivers for consumers A & B must be mapped to the correct regulator in
+order to control their power supply. This mapping can be achieved in machine
+initialisation code by calling :-
+
+int regulator_set_device_supply(const char *regulator, struct device *dev,
+ const char *supply);
+
+and is shown with the following code :-
+
+regulator_set_device_supply("Regulator-1", devB, "Vcc");
+regulator_set_device_supply("Regulator-2", devA, "Vcc");
+
+This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2
+to the 'Vcc' supply for Consumer A.
+
+
+2. Regulator supply configuration.
+==================================
+Consider the following machine (again) :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+Regulator-1 supplies power to Regulator-2. This relationship must be registered
+with the core so that Regulator-1 is also enabled when Consumer A enables it's
+supply (Regulator-2).
+
+This relationship can be register with the core via :-
+
+int regulator_set_supply(const char *regulator, const char *regulator_supply);
+
+In this example we would use the following code :-
+
+regulator_set_supply("Regulator-2", "Regulator-1");
+
+Relationships can be queried by calling :-
+
+const char *regulator_get_supply(const char *regulator);
+
+
+3. Power Domain constraint setting.
+===================================
+Each power domain within a system has physical constraints on voltage and
+current. This must be defined in software so that the power domain is always
+operated within specifications.
+
+Consider the following machine (again) :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+This gives us two regulators and two power domains:
+
+ Domain 1: Regulator-2, Consumer B.
+ Domain 2: Consumer A.
+
+Constraints can be registered by calling :-
+
+int regulator_set_platform_constraints(const char *regulator,
+ struct regulation_constraints *constraints);
+
+The example is defined as follows :-
+
+struct regulation_constraints domain_1 = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+struct regulation_constraints domain_2 = {
+ .min_uV = 1800000,
+ .max_uV = 2000000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+regulator_set_platform_constraints("Regulator-1", &domain_1);
+regulator_set_platform_constraints("Regulator-2", &domain_2);
--- /dev/null
+Linux voltage and current regulator framework
+=============================================
+
+About
+=====
+
+This framework is designed to provide a standard kernel interface to control
+voltage and current regulators.
+
+The intention is to allow systems to dynamically control regulator power output
+in order to save power and prolong battery life. This applies to both voltage
+regulators (where voltage output is controllable) and current sinks (where
+current limit is controllable).
+
+(C) 2008 Wolfson Microelectronics PLC.
+Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+
+
+Nomenclature
+============
+
+Some terms used in this document:-
+
+ o Regulator - Electronic device that supplies power to other devices.
+ Most regulators can enable and disable their output whilst
+ some can control their output voltage and or current.
+
+ Input Voltage -> Regulator -> Output Voltage
+
+
+ o PMIC - Power Management IC. An IC that contains numerous regulators
+ and often contains other susbsystems.
+
+
+ o Consumer - Electronic device that is supplied power by a regulator.
+ Consumers can be classified into two types:-
+
+ Static: consumer does not change it's supply voltage or
+ current limit. It only needs to enable or disable it's
+ power supply. It's supply voltage is set by the hardware,
+ bootloader, firmware or kernel board initialisation code.
+
+ Dynamic: consumer needs to change it's supply voltage or
+ current limit to meet operation demands.
+
+
+ o Power Domain - Electronic circuit that is supplied it's input power by the
+ output power of a regulator, switch or by another power
+ domain.
+
+ The supply regulator may be behind a switch(s). i.e.
+
+ Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A]
+ | |
+ | +-> [Consumer B], [Consumer C]
+ |
+ +-> [Consumer D], [Consumer E]
+
+ That is one regulator and three power domains:
+
+ Domain 1: Switch-1, Consumers D & E.
+ Domain 2: Switch-2, Consumers B & C.
+ Domain 3: Consumer A.
+
+ and this represents a "supplies" relationship:
+
+ Domain-1 --> Domain-2 --> Domain-3.
+
+ A power domain may have regulators that are supplied power
+ by other regulators. i.e.
+
+ Regulator-1 -+-> Regulator-2 -+-> [Consumer A]
+ |
+ +-> [Consumer B]
+
+ This gives us two regulators and two power domains:
+
+ Domain 1: Regulator-2, Consumer B.
+ Domain 2: Consumer A.
+
+ and a "supplies" relationship:
+
+ Domain-1 --> Domain-2
+
+
+ o Constraints - Constraints are used to define power levels for performance
+ and hardware protection. Constraints exist at three levels:
+
+ Regulator Level: This is defined by the regulator hardware
+ operating parameters and is specified in the regulator
+ datasheet. i.e.
+
+ - voltage output is in the range 800mV -> 3500mV.
+ - regulator current output limit is 20mA @ 5V but is
+ 10mA @ 10V.
+
+ Power Domain Level: This is defined in software by kernel
+ level board initialisation code. It is used to constrain a
+ power domain to a particular power range. i.e.
+
+ - Domain-1 voltage is 3300mV
+ - Domain-2 voltage is 1400mV -> 1600mV
+ - Domain-3 current limit is 0mA -> 20mA.
+
+ Consumer Level: This is defined by consumer drivers
+ dynamically setting voltage or current limit levels.
+
+ e.g. a consumer backlight driver asks for a current increase
+ from 5mA to 10mA to increase LCD illumination. This passes
+ to through the levels as follows :-
+
+ Consumer: need to increase LCD brightness. Lookup and
+ request next current mA value in brightness table (the
+ consumer driver could be used on several different
+ personalities based upon the same reference device).
+
+ Power Domain: is the new current limit within the domain
+ operating limits for this domain and system state (e.g.
+ battery power, USB power)
+
+ Regulator Domains: is the new current limit within the
+ regulator operating parameters for input/ouput voltage.
+
+ If the regulator request passes all the constraint tests
+ then the new regulator value is applied.
+
+
+Design
+======
+
+The framework is designed and targeted at SoC based devices but may also be
+relevant to non SoC devices and is split into the following four interfaces:-
+
+
+ 1. Consumer driver interface.
+
+ This uses a similar API to the kernel clock interface in that consumer
+ drivers can get and put a regulator (like they can with clocks atm) and
+ get/set voltage, current limit, mode, enable and disable. This should
+ allow consumers complete control over their supply voltage and current
+ limit. This also compiles out if not in use so drivers can be reused in
+ systems with no regulator based power control.
+
+ See Documentation/power/regulator/consumer.txt
+
+ 2. Regulator driver interface.
+
+ This allows regulator drivers to register their regulators and provide
+ operations to the core. It also has a notifier call chain for propagating
+ regulator events to clients.
+
+ See Documentation/power/regulator/regulator.txt
+
+ 3. Machine interface.
+
+ This interface is for machine specific code and allows the creation of
+ voltage/current domains (with constraints) for each regulator. It can
+ provide regulator constraints that will prevent device damage through
+ overvoltage or over current caused by buggy client drivers. It also
+ allows the creation of a regulator tree whereby some regulators are
+ supplied by others (similar to a clock tree).
+
+ See Documentation/power/regulator/machine.txt
+
+ 4. Userspace ABI.
+
+ The framework also exports a lot of useful voltage/current/opmode data to
+ userspace via sysfs. This could be used to help monitor device power
+ consumption and status.
+
+ See Documentation/ABI/testing/regulator-sysfs.txt
--- /dev/null
+Regulator Driver Interface
+==========================
+
+The regulator driver interface is relatively simple and designed to allow
+regulator drivers to register their services with the core framework.
+
+
+Registration
+============
+
+Drivers can register a regulator by calling :-
+
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+ void *reg_data);
+
+This will register the regulators capabilities and operations the regulator
+core. The core does not touch reg_data (private to regulator driver).
+
+Regulators can be unregistered by calling :-
+
+void regulator_unregister(struct regulator_dev *rdev);
+
+
+Regulator Events
+================
+Regulators can send events (e.g. over temp, under voltage, etc) to consumer
+drivers by calling :-
+
+int regulator_notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data);
- MPC5200 Device Tree Bindings
ppc_htab.txt
- info about the Linux/PPC /proc/ppc_htab entry
-SBC8260_memory_mapping.txt
- - EST SBC8260 board info
smp.txt
- use and state info about Linux/PPC on MP machines
sound.txt
+++ /dev/null
-Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com)
-if you have questions, comments or corrections.
-
- * EST SBC8260 Linux memory mapping rules
-
- http://www.estc.com/
- http://www.estc.com/products/boards/SBC8260-8240_ds.html
-
- Initial conditions:
- -------------------
-
- Tasks that need to be perform by the boot ROM before control is
- transferred to zImage (compressed Linux kernel):
-
- - Define the IMMR to 0xf0000000
-
- - Initialize the memory controller so that RAM is available at
- physical address 0x00000000. On the SBC8260 is this 16M (64M)
- SDRAM.
-
- - The boot ROM should only clear the RAM that it is using.
-
- The reason for doing this is to enhances the chances of a
- successful post mortem on a Linux panic. One of the first
- items to examine is the 16k (LOG_BUF_LEN) circular console
- buffer called log_buf which is defined in kernel/printk.c.
-
- - To enhance boot ROM performance, the I-cache can be enabled.
-
- Date: Mon, 22 May 2000 14:21:10 -0700
- From: Neil Russell <caret@c-side.com>
-
- LiMon (LInux MONitor) runs with and starts Linux with MMU
- off, I-cache enabled, D-cache disabled. The I-cache doesn't
- need hints from the MMU to work correctly as the D-cache
- does. No D-cache means no special code to handle devices in
- the presence of cache (no snooping, etc). The use of the
- I-cache means that the monitor can run acceptably fast
- directly from ROM, rather than having to copy it to RAM.
-
- - Build the board information structure (see
- include/asm-ppc/est8260.h for its definition)
-
- - The compressed Linux kernel (zImage) contains a bootstrap loader
- that is position independent; you can load it into any RAM,
- ROM or FLASH memory address >= 0x00500000 (above 5 MB), or
- at its link address of 0x00400000 (4 MB).
-
- Note: If zImage is loaded at its link address of 0x00400000 (4 MB),
- then zImage will skip the step of moving itself to
- its link address.
-
- - Load R3 with the address of the board information structure
-
- - Transfer control to zImage
-
- - The Linux console port is SMC1, and the baud rate is controlled
- from the bi_baudrate field of the board information structure.
- On thing to keep in mind when picking the baud rate, is that
- there is no flow control on the SMC ports. I would stick
- with something safe and standard like 19200.
-
- On the EST SBC8260, the SMC1 port is on the COM1 connector of
- the board.
-
-
- EST SBC8260 defaults:
- ---------------------
-
- Chip
- Memory Sel Bus Use
- --------------------- --- --- ----------------------------------
- 0x00000000-0x03FFFFFF CS2 60x (16M or 64M)/64M SDRAM
- 0x04000000-0x04FFFFFF CS4 local 4M/16M SDRAM (soldered to the board)
- 0x21000000-0x21000000 CS7 60x 1B/64K Flash present detect (from the flash SIMM)
- 0x21000001-0x21000001 CS7 60x 1B/64K Switches (read) and LEDs (write)
- 0x22000000-0x2200FFFF CS5 60x 8K/64K EEPROM
- 0xFC000000-0xFCFFFFFF CS6 60x 2M/16M flash (8 bits wide, soldered to the board)
- 0xFE000000-0xFFFFFFFF CS0 60x 4M/16M flash (SIMM)
-
- Notes:
- ------
-
- - The chip selects can map 32K blocks and up (powers of 2)
-
- - The SDRAM machine can handled up to 128Mbytes per chip select
-
- - Linux uses the 60x bus memory (the SDRAM DIMM) for the
- communications buffers.
-
- - BATs can map 128K-256Mbytes each. There are four data BATs and
- four instruction BATs. Generally the data and instruction BATs
- are mapped the same.
-
- - The IMMR must be set above the kernel virtual memory addresses,
- which start at 0xC0000000. Otherwise, the kernel may crash as
- soon as you start any threads or processes due to VM collisions
- in the kernel or user process space.
-
-
- Details from Dan Malek <dan_malek@mvista.com> on 10/29/1999:
-
- The user application virtual space consumes the first 2 Gbytes
- (0x00000000 to 0x7FFFFFFF). The kernel virtual text starts at
- 0xC0000000, with data following. There is a "protection hole"
- between the end of kernel data and the start of the kernel
- dynamically allocated space, but this space is still within
- 0xCxxxxxxx.
-
- Obviously the kernel can't map any physical addresses 1:1 in
- these ranges.
-
-
- Details from Dan Malek <dan_malek@mvista.com> on 5/19/2000:
-
- During the early kernel initialization, the kernel virtual
- memory allocator is not operational. Prior to this KVM
- initialization, we choose to map virtual to physical addresses
- 1:1. That is, the kernel virtual address exactly matches the
- physical address on the bus. These mappings are typically done
- in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c. Only
- absolutely necessary mappings should be done at this time, for
- example board control registers or a serial uart. Normal device
- driver initialization should map resources later when necessary.
-
- Although platform dependent, and certainly the case for embedded
- 8xx, traditionally memory is mapped at physical address zero,
- and I/O devices above physical address 0x80000000. The lowest
- and highest (above 0xf0000000) I/O addresses are traditionally
- used for devices or registers we need to map during kernel
- initialization and prior to KVM operation. For this reason,
- and since it followed prior PowerPC platform examples, I chose
- to map the embedded 8xx kernel to the 0xc0000000 virtual address.
- This way, we can enable the MMU to map the kernel for proper
- operation, and still map a few windows before the KVM is operational.
-
- On some systems, you could possibly run the kernel at the
- 0x80000000 or any other virtual address. It just depends upon
- mapping that must be done prior to KVM operational. You can never
- map devices or kernel spaces that overlap with the user virtual
- space. This is why default IMMR mapping used by most BDM tools
- won't work. They put the IMMR at something like 0x10000000 or
- 0x02000000 for example. You simply can't map these addresses early
- in the kernel, and continue proper system operation.
-
- The embedded 8xx/82xx kernel is mature enough that all you should
- need to do is map the IMMR someplace at or above 0xf0000000 and it
- should boot far enough to get serial console messages and KGDB
- connected on any platform. There are lots of other subtle memory
- management design features that you simply don't need to worry
- about. If you are changing functions related to MMU initialization,
- you are likely breaking things that are known to work and are
- heading down a path of disaster and frustration. Your changes
- should be to make the flexibility of the processor fit Linux,
- not force arbitrary and non-workable memory mappings into Linux.
-
- - You don't want to change KERNELLOAD or KERNELBASE, otherwise the
- virtual memory and MMU code will get confused.
-
- arch/ppc/Makefile:KERNELLOAD = 0xc0000000
-
- include/asm-ppc/page.h:#define PAGE_OFFSET 0xc0000000
- include/asm-ppc/page.h:#define KERNELBASE PAGE_OFFSET
-
- - RAM is at physical address 0x00000000, and gets mapped to
- virtual address 0xC0000000 for the kernel.
-
-
- Physical addresses used by the Linux kernel:
- --------------------------------------------
-
- 0x00000000-0x3FFFFFFF 1GB reserved for RAM
- 0xF0000000-0xF001FFFF 128K IMMR 64K used for dual port memory,
- 64K for 8260 registers
-
-
- Logical addresses used by the Linux kernel:
- -------------------------------------------
-
- 0xF0000000-0xFFFFFFFF 256M BAT0 (IMMR: dual port RAM, registers)
- 0xE0000000-0xEFFFFFFF 256M BAT1 (I/O space for custom boards)
- 0xC0000000-0xCFFFFFFF 256M BAT2 (RAM)
- 0xD0000000-0xDFFFFFFF 256M BAT3 (if RAM > 256MByte)
-
-
- EST SBC8260 Linux mapping:
- --------------------------
-
- DBAT0, IBAT0, cache inhibited:
-
- Chip
- Memory Sel Use
- --------------------- --- ---------------------------------
- 0xF0000000-0xF001FFFF n/a IMMR: dual port RAM, registers
-
- DBAT1, IBAT1, cache inhibited:
-
a 64-bit platform.
d) request and get assigned a platform number (see PLATFORM_*
- constants in include/asm-powerpc/processor.h
+ constants in arch/powerpc/include/asm/processor.h
32-bit embedded kernels:
---------
The kernel is entered with r3 pointing to an area of memory that is
- roughly described in include/asm-powerpc/prom.h by the structure
+ roughly described in arch/powerpc/include/asm/prom.h by the structure
boot_param_header:
struct boot_param_header {
- fsl,cpm2-scc-uart
- fsl,qe-uart
+Modem control lines connected to GPIO controllers are listed in the gpios
+property as described in booting-without-of.txt, section IX.1 in the following
+order:
+
+CTS, RTS, DCD, DSR, DTR, and RI.
+
+The gpios property is optional and can be left out when control lines are
+not used.
+
Example:
serial@11a00 {
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
fsl,cpm-command = <00800000>;
+ gpios = <&gpio_c 15 0
+ &gpio_d 29 0>;
};
pci_get_device_by_addr() will find the pci device associated
with that address (if any).
-The default include/asm-powerpc/io.h macros readb(), inb(), insb(),
+The default arch/powerpc/include/asm/io.h macros readb(), inb(), insb(),
etc. include a check to see if the i/o read returned all-0xff's.
If so, these make a call to eeh_dn_check_failure(), which in turn
asks the firmware if the all-ff's value is the sign of a true EEH
rfkill input line is active. Only if none of the rfkill input lines are
active, will it return RFKILL_STATE_UNBLOCKED.
-If it doesn't implement the get_state() hook, it must make sure that its calls
-to rfkill_force_state() are enough to keep the status always up-to-date, and it
-must do a rfkill_force_state() on resume from sleep.
+Since the device has a hardware rfkill line, it IS subject to state changes
+external to rfkill. Therefore, the driver must make sure that it calls
+rfkill_force_state() to keep the status always up-to-date, and it must do a
+rfkill_force_state() on resume from sleep.
Every time the driver gets a notification from the card that one of its rfkill
lines changed state (polling might be needed on badly designed cards that don't
about its current state).
The rfkill class will call the get_state hook of a device every time it needs
-to know the *real* current state of the hardware. This can happen often.
+to know the *real* current state of the hardware. This can happen often, but
+it does not do any polling, so it is not enough on hardware that is subject
+to state changes outside of the rfkill subsystem.
+
+Therefore, calling rfkill_force_state() when a state change happens is
+mandatory when the device has a hardware rfkill line, or when something else
+like the firmware could cause its state to be changed without going through the
+rfkill class.
Some hardware provides events when its status changes. In these cases, it is
best for the driver to not provide a get_state hook, and instead register the
rfkill class *already* with the correct status, and keep it updated using
rfkill_force_state() when it gets an event from the hardware.
+rfkill_force_state() must be used on the device resume handlers to update the
+rfkill status, should there be any chance of the device status changing during
+the sleep.
+
There is no provision for a statically-allocated rfkill struct. You must
use rfkill_allocate() to allocate one.
-----------------------------------
Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
"platform device". The master configuration is passed to the driver via a table
-found in include/asm-arm/arch-pxa/pxa2xx_spi.h:
+found in arch/arm/mach-pxa/include/mach/pxa2xx_spi.h:
struct pxa2xx_spi_master {
enum pxa_ssp_type ssp_type;
Each slave device attached to the PXA must provide slave specific configuration
information via the structure "pxa2xx_spi_chip" found in
-"include/asm-arm/arch-pxa/pxa2xx_spi.h". The pxa2xx_spi master controller driver
+"arch/arm/mach-pxa/include/mach/pxa2xx_spi.h". The pxa2xx_spi master controller driver
will uses the configuration whenever the driver communicates with the slave
device.
So for example arch/.../mach-*/board-*.c files might have code like:
- #include <asm/arch/spi.h> /* for mysoc_spi_data */
+ #include <mach/spi.h> /* for mysoc_spi_data */
/* if your mach-* infrastructure doesn't support kernels that can
* run on multiple boards, pdata wouldn't benefit from "__init".
And SOC-specific utility code might look something like:
- #include <asm/arch/spi.h>
+ #include <mach/spi.h>
static struct platform_device spi2 = { ... };
sonixj 0c45:6138 Sn9c120 Mo4000
sonixj 0c45:613b Surfer SN-206
sonixj 0c45:613c Sonix Pccam168
+sonixj 0c45:6143 Sonix Pccam168
sunplus 0d64:0303 Sunplus FashionCam DXG
etoms 102c:6151 Qcam Sangha CIF
etoms 102c:6251 Qcam xxxxxx VGA
W: http://www.openezx.org/
S: Maintained
+ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
+P: Sascha Hauer
+M: kernel@pengutronix.de
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+S: Maintained
+
ARM/GLOMATION GESBC9312SX MACHINE SUPPORT
P: Lennert Buytenhek
M: kernel@wantstofly.org
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
+ARM/MAGICIAN MACHINE SUPPORT
+P: Philipp Zabel
+M: philipp.zabel@gmail.com
+S: Maintained
+
ARM/TOSA MACHINE SUPPORT
P: Dmitry Baryshkov
M: dbaryshkov@gmail.com
L: ath5k-devel@lists.ath5k.org
S: Maintained
+ATHEROS ATH9K WIRELESS DRIVER
+P: Luis R. Rodriguez
+M: lrodriguez@atheros.com
+P: Jouni Malinen
+M: jmalinen@atheros.com
+L: linux-wireless@vger.kernel.org
+L: ath9k-devel@lists.ath9k.org
+S: Supported
+
ATI_REMOTE2 DRIVER
P: Ville Syrjala
M: syrjala@sci.fi
S: Maintained
HARDWARE MONITORING
-P: Mark M. Hoffman
-M: mhoffman@lightlink.com
L: lm-sensors@lm-sensors.org
W: http://www.lm-sensors.org/
-T: git lm-sensors.org:/kernel/mhoffman/hwmon-2.6.git testing
-T: git lm-sensors.org:/kernel/mhoffman/hwmon-2.6.git release
-S: Maintained
+S: Orphaned
HARDWARE RANDOM NUMBER GENERATOR CORE
S: Orphaned
L: linux-sh@vger.kernel.org
W: http://www.linux-sh.org
T: git kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.git
-S: Maintained
+S: Supported
SUN3/3X
P: Sam Creasey
L: netdev@vger.kernel.org
S: Maintained
+VOLTAGE AND CURRENT REGULATOR FRAMEWORK
+P: Liam Girdwood
+M: lg@opensource.wolfsonmicro.com
+P: Mark Brown
+M: broonie@opensource.wolfsonmicro.com
+W: http://opensource.wolfsonmicro.com/node/15
+T: git kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6.git
+S: Supported
+
VT1211 HARDWARE MONITOR DRIVER
P: Juerg Haefliger
M: juergh@gmail.com
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 27
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc2
NAME = Rotary Wombat
# *DOCUMENTATION*
echo " in the '$(srctree)' directory.";\
/bin/false; \
fi;
- $(Q)if [ ! -d include2 ]; then mkdir -p include2; fi;
- $(Q)if [ -e $(srctree)/include/asm-$(SRCARCH)/system.h ]; then \
+ $(Q)if [ ! -d include2 ]; then \
+ mkdir -p include2; \
ln -fsn $(srctree)/include/asm-$(SRCARCH) include2/asm; \
- fi
+ fi
endif
# prepare2 creates a makefile if using a separate output directory
cmd_cscope-file = (echo \-k; echo \-q; $(all-sources)) > cscope.files
quiet_cmd_cscope = MAKE cscope.out
- cmd_cscope = cscope -b
+ cmd_cscope = cscope -b -f cscope.out
cscope: FORCE
$(call cmd,cscope-file)
source "drivers/dca/Kconfig"
+source "drivers/regulator/Kconfig"
+
source "drivers/uio/Kconfig"
endmenu
machine-$(CONFIG_ARCH_RPC) := rpc
machine-$(CONFIG_ARCH_EBSA110) := ebsa110
machine-$(CONFIG_ARCH_CLPS7500) := clps7500
- incdir-$(CONFIG_ARCH_CLPS7500) := cl7500
machine-$(CONFIG_FOOTBRIDGE) := footbridge
- incdir-$(CONFIG_FOOTBRIDGE) := ebsa285
machine-$(CONFIG_ARCH_SHARK) := shark
machine-$(CONFIG_ARCH_SA1100) := sa1100
ifeq ($(CONFIG_ARCH_SA1100),y)
machine-$(CONFIG_ARCH_IOP32X) := iop32x
machine-$(CONFIG_ARCH_IOP33X) := iop33x
machine-$(CONFIG_ARCH_IOP13XX) := iop13xx
+ plat-$(CONFIG_PLAT_IOP) := iop
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_IXP2000) := ixp2000
machine-$(CONFIG_ARCH_IXP23XX) := ixp23xx
machine-$(CONFIG_ARCH_OMAP1) := omap1
machine-$(CONFIG_ARCH_OMAP2) := omap2
- incdir-$(CONFIG_ARCH_OMAP) := omap
- machine-$(CONFIG_ARCH_S3C2410) := s3c2410
+ plat-$(CONFIG_ARCH_OMAP) := omap
+ machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2400 s3c2412 s3c2440 s3c2442 s3c2443
+ plat-$(CONFIG_PLAT_S3C24XX) := s3c24xx
machine-$(CONFIG_ARCH_LH7A40X) := lh7a40x
machine-$(CONFIG_ARCH_VERSATILE) := versatile
machine-$(CONFIG_ARCH_IMX) := imx
machine-$(CONFIG_ARCH_DAVINCI) := davinci
machine-$(CONFIG_ARCH_KIRKWOOD) := kirkwood
machine-$(CONFIG_ARCH_KS8695) := ks8695
- incdir-$(CONFIG_ARCH_MXC) := mxc
+ plat-$(CONFIG_ARCH_MXC) := mxc
machine-$(CONFIG_ARCH_MX2) := mx2
machine-$(CONFIG_ARCH_MX3) := mx3
machine-$(CONFIG_ARCH_ORION5X) := orion5x
+ plat-$(CONFIG_PLAT_ORION) := orion
machine-$(CONFIG_ARCH_MSM7X00A) := msm
machine-$(CONFIG_ARCH_LOKI) := loki
machine-$(CONFIG_ARCH_MV78XX0) := mv78xx0
# The byte offset of the kernel image in RAM from the start of RAM.
TEXT_OFFSET := $(textofs-y)
-ifeq ($(incdir-y),)
-incdir-y := $(machine-y)
-endif
-INCDIR := arch-$(incdir-y)
-
+# The first directory contains additional information for the boot setup code
ifneq ($(machine-y),)
-MACHINE := arch/arm/mach-$(machine-y)/
+MACHINE := arch/arm/mach-$(word 1,$(machine-y))/
else
MACHINE :=
endif
+machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
+platdirs := $(patsubst %,arch/arm/plat-%/,$(plat-y))
+
+ifeq ($(KBUILD_SRC),)
+KBUILD_CPPFLAGS += $(patsubst %,-I%include,$(machdirs) $(platdirs))
+else
+KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%include,$(machdirs) $(platdirs))
+endif
+
export TEXT_OFFSET GZFLAGS MMUEXT
# Do we have FASTFPE?
# If we have a machine-specific directory, then include it in the build.
core-y += arch/arm/kernel/ arch/arm/mm/ arch/arm/common/
-core-y += $(MACHINE)
-core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2400/
-core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2412/
-core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2440/
-core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2442/
-core-$(CONFIG_ARCH_S3C2410) += arch/arm/mach-s3c2443/
+core-y += $(machdirs) $(platdirs)
core-$(CONFIG_FPE_NWFPE) += arch/arm/nwfpe/
core-$(CONFIG_FPE_FASTFPE) += $(FASTFPE_OBJ)
core-$(CONFIG_VFP) += arch/arm/vfp/
-# If we have a common platform directory, then include it in the build.
-core-$(CONFIG_PLAT_IOP) += arch/arm/plat-iop/
-core-$(CONFIG_PLAT_ORION) += arch/arm/plat-orion/
-core-$(CONFIG_ARCH_OMAP) += arch/arm/plat-omap/
-core-$(CONFIG_PLAT_S3C24XX) += arch/arm/plat-s3c24xx/
-core-$(CONFIG_ARCH_MXC) += arch/arm/plat-mxc/
-
drivers-$(CONFIG_OPROFILE) += arch/arm/oprofile/
libs-y := arch/arm/lib/ $(libs-y)
# them changed. We use .arch to indicate when they were updated
# last, otherwise make uses the target directory mtime.
-include/asm-arm/.arch: $(wildcard include/config/arch/*.h) include/config/auto.conf
- @echo ' SYMLINK include/asm-arm/arch -> include/asm-arm/$(INCDIR)'
-ifneq ($(KBUILD_SRC),)
- $(Q)mkdir -p include/asm-arm
- $(Q)ln -fsn $(srctree)/include/asm-arm/$(INCDIR) include/asm-arm/arch
-else
- $(Q)ln -fsn $(INCDIR) include/asm-arm/arch
-endif
- @touch $@
-
archprepare: maketools
PHONY += maketools FORCE
-maketools: include/linux/version.h include/asm-arm/.arch FORCE
+maketools: include/linux/version.h FORCE
$(Q)$(MAKE) $(build)=arch/arm/tools include/asm-arm/mach-types.h
# Convert bzImage to zImage
$(obj)/vmlinux.lds: $(obj)/vmlinux.lds.in arch/arm/boot/Makefile .config
@sed "$(SEDFLAGS)" < $< > $@
-
-$(obj)/misc.o: $(obj)/misc.c include/asm/arch/uncompress.h lib/inflate.c
-
*/
#include <linux/linkage.h>
-#include <asm/mach-types.h>
.section ".start", "ax"
#else
-#include <asm/arch/debug-macro.S>
+#include <mach/debug-macro.S>
.macro writeb, ch, rb
senduart \ch, \rb
static void putstr(const char *ptr);
#include <linux/compiler.h>
-#include <asm/arch/uncompress.h>
+#include <mach/uncompress.h>
#ifdef CONFIG_DEBUG_ICEDCC
#include <linux/slab.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <linux/dma-mapping.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/apm-emulation.h>
#include <linux/suspend.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/sharpsl.h>
+#include <mach/pm.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/sharpsl.h>
#include <asm/hardware/sharpsl_pm.h>
/*
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/hardware/ioc.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/string.h>
-#include <asm/hardware.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/uengine.h>
#include <asm/io.h>
# AT91 Board Options
#
CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# AT91 Board Options
#
# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
-# CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
+# CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16 is not set
#
# AT91 Feature Selections
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ONENAND is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-# CONFIG_MTD_NAND_AT91_ECC_SOFT is not set
-CONFIG_MTD_NAND_AT91_ECC_HW=y
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+# CONFIG_MTD_NAND_ATMEL_ECC_SOFT is not set
+CONFIG_MTD_NAND_ATMEL_ECC_HW=y
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_ONENAND is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
-CONFIG_MTD_NAND_AT91=y
-CONFIG_MTD_NAND_AT91_ECC_SOFT=y
-# CONFIG_MTD_NAND_AT91_ECC_HW is not set
-# CONFIG_MTD_NAND_AT91_ECC_NONE is not set
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
+# CONFIG_MTD_NAND_ATMEL_ECC_HW is not set
+# CONFIG_MTD_NAND_ATMEL_ECC_NONE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
# CONFIG_MTD_NAND_MUSEUM_IDS is not set
CONFIG_MTD_NAND_IDS=y
-CONFIG_MTD_NAND_AT91=y
+CONFIG_MTD_NAND_ATMEL=y
# CONFIG_MTD_NAND_NANDSIM is not set
CONFIG_MTD_NAND_PLATFORM=y
# CONFIG_MTD_ALAUDA is not set
/*
- * linux/include/asm-arm/assembler.h
+ * arch/arm/include/asm/assembler.h
*
* Copyright (C) 1996-2000 Russell King
*
/*
- * linux/include/asm-arm/atomic.h
+ * arch/arm/include/asm/atomic.h
*
* Copyright (C) 1996 Russell King.
* Copyright (C) 2002 Deep Blue Solutions Ltd.
/*
- * linux/include/asm-arm/bugs.h
+ * arch/arm/include/asm/bugs.h
*
* Copyright (C) 1995-2003 Russell King
*
/*
- * linux/include/asm-arm/byteorder.h
+ * arch/arm/include/asm/byteorder.h
*
* ARM Endian-ness. In little endian mode, the data bus is connected such
* that byte accesses appear as:
/*
- * linux/include/asm-arm/cache.h
+ * arch/arm/include/asm/cache.h
*/
#ifndef __ASMARM_CACHE_H
#define __ASMARM_CACHE_H
/*
- * linux/include/asm-arm/cacheflush.h
+ * arch/arm/include/asm/cacheflush.h
*
* Copyright (C) 1999-2002 Russell King
*
/*
- * linux/include/asm-arm/checksum.h
+ * arch/arm/include/asm/checksum.h
*
* IP checksum routines
*
/*
- * linux/include/asm-arm/cpu-multi32.h
+ * arch/arm/include/asm/cpu-multi32.h
*
* Copyright (C) 2000 Russell King
*
/*
- * linux/include/asm-arm/cpu-single.h
+ * arch/arm/include/asm/cpu-single.h
*
* Copyright (C) 2000 Russell King
*
/*
- * linux/include/asm-arm/cpu.h
+ * arch/arm/include/asm/cpu.h
*
* Copyright (C) 2004-2005 ARM Ltd.
*
#include <linux/spinlock.h>
#include <asm/system.h>
#include <asm/scatterlist.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
/*
* This is the maximum virtual address which can be DMA'd from.
/*
- * linux/include/asm-arm/domain.h
+ * arch/arm/include/asm/domain.h
*
* Copyright (C) 1999 Russell King.
*
/*
- * linux/include/asm-arm/ecard.h
+ * arch/arm/include/asm/ecard.h
*
* definitions for expansion cards
*
/*
- * linux/include/asm-arm/fiq.h
+ * arch/arm/include/asm/fiq.h
*
* Support for FIQ on ARM architectures.
* Written by Philip Blundell <philb@gnu.org>, 1998
/*
- * include/asm-arm/flat.h -- uClinux flat-format executables
+ * arch/arm/include/asm/flat.h -- uClinux flat-format executables
*/
#ifndef __ARM_FLAT_H__
/*
- * linux/include/asm-arm/floppy.h
+ * arch/arm/include/asm/floppy.h
*
* Copyright (C) 1996-2000 Russell King
*
#ifndef __ASM_ARM_FLOPPY_H
#define __ASM_ARM_FLOPPY_H
#if 0
-#include <asm/arch/floppy.h>
+#include <mach/floppy.h>
#endif
#define fd_outb(val,port) \
/*
- * linux/include/asm-arm/fpstate.h
+ * arch/arm/include/asm/fpstate.h
*
* Copyright (C) 1995 Russell King
*
/*
- * linux/include/asm-arm/glue.h
+ * arch/arm/include/asm/glue.h
*
* Copyright (C) 1997-1999 Russell King
* Copyright (C) 2000-2002 Deep Blue Solutions Ltd.
#define _ARCH_ARM_GPIO_H
/* not all ARM platforms necessarily support this API ... */
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#endif /* _ARCH_ARM_GPIO_H */
/*
- * include/asm-arm/hardware/cache-l2x0.h
+ * arch/arm/include/asm/hardware/cache-l2x0.h
*
* Copyright (C) 2007 ARM Limited
*
/*
- * linux/include/asm-arm/hardware/clps7111.h
+ * arch/arm/include/asm/hardware/clps7111.h
*
* This file contains the hardware definitions of the CLPS7111 internal
* registers.
/*
- * linux/include/asm-arm/hardware/cs89712.h
+ * arch/arm/include/asm/hardware/cs89712.h
*
* This file contains the hardware definitions of the CS89712
* additional internal registers.
/*
- * linux/include/asm-arm/hardware/debug-8250.S
+ * arch/arm/include/asm/hardware/debug-8250.S
*
* Copyright (C) 1994-1999 Russell King
*
-/* linux/include/asm-arm/hardware/debug-pl01x.S
+/* arch/arm/include/asm/hardware/debug-pl01x.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/hardware/dec21285.h
+ * arch/arm/include/asm/hardware/dec21285.h
*
* Copyright (C) 1998 Russell King
*
#define DC21285_PCI_MEM 0x80000000
#ifndef __ASSEMBLY__
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define DC21285_IO(x) ((volatile unsigned long *)(ARMCSR_BASE+(x)))
#else
#define DC21285_IO(x) (x)
/*
- * include/asm-arm/hardware/entry-macro-iomd.S
+ * arch/arm/include/asm/hardware/entry-macro-iomd.S
*
* Low-level IRQ helper macros for IOC/IOMD based platforms
*
/*
- * linux/include/asm-arm/hardware/ep7211.h
+ * arch/arm/include/asm/hardware/ep7211.h
*
* This file contains the hardware definitions of the EP7211 internal
* registers.
/*
- * linux/include/asm-arm/hardware/ep7212.h
+ * arch/arm/include/asm/hardware/ep7212.h
*
* This file contains the hardware definitions of the EP7212 internal
* registers.
/*
- * linux/include/asm-arm/hardware/gic.h
+ * arch/arm/include/asm/hardware/gic.h
*
* Copyright (C) 2002 ARM Limited, All Rights Reserved.
*
/*
- * linux/include/asm-arm/hardware/icst307.h
+ * arch/arm/include/asm/hardware/icst307.h
*
* Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
*
/*
- * linux/include/asm-arm/hardware/icst525.h
+ * arch/arm/include/asm/hardware/icst525.h
*
* Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
*
/*
- * linux/include/asm-arm/hardware/ioc.h
+ * arch/arm/include/asm/hardware/ioc.h
*
* Copyright (C) Russell King
*
/*
- * linux/include/asm-arm/hardware/iomd.h
+ * arch/arm/include/asm/hardware/iomd.h
*
* Copyright (C) 1999 Russell King
*
#define _ADMA_H
#include <linux/types.h>
#include <linux/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iop_adma.h>
/* Memory copy units */
/*
- * linux/include/asm-arm/hardware/iop3xx-gpio.h
+ * arch/arm/include/asm/hardware/iop3xx-gpio.h
*
* IOP3xx GPIO wrappers
*
#ifndef __ASM_ARM_HARDWARE_IOP3XX_GPIO_H
#define __ASM_ARM_HARDWARE_IOP3XX_GPIO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm-generic/gpio.h>
#define IOP3XX_N_GPIOS 8
/*
- * include/asm-arm/hardware/iop3xx.h
+ * arch/arm/include/asm/hardware/iop3xx.h
*
* Intel IOP32X and IOP33X register definitions
*
/*
- * linux/include/asm-arm/hardware/locomo.h
+ * arch/arm/include/asm/hardware/locomo.h
*
* This file contains the definitions for the LoCoMo G/A Chip
*
/*
- * linux/include/asm-arm/hardware/memc.h
+ * arch/arm/include/asm/hardware/memc.h
*
* Copyright (C) Russell King.
*
/*
- * linux/include/asm-arm/hardware/pci_v3.h
+ * arch/arm/include/asm/hardware/pci_v3.h
*
* Internal header file PCI V3 chip
*
/*
- * linux/include/asm-arm/hardware/sa1111.h
+ * arch/arm/include/asm/hardware/sa1111.h
*
* Copyright (C) 2000 John G Dorsey <john+@cs.cmu.edu>
*
#ifndef _ASM_ARCH_SA1111
#define _ASM_ARCH_SA1111
-#include <asm/arch/bitfield.h>
+#include <mach/bitfield.h>
/*
* The SA1111 is always located at virtual 0xf4000000, and is always
/*
- * linux/include/asm-arm/hardware/vic.h
+ * arch/arm/include/asm/hardware/vic.h
*
* Copyright (c) ARM Limited 2003. All rights reserved.
*
--- /dev/null
+/*
+ * Nothing to see here yet
+ */
+#ifndef _ARCH_ARM_HW_IRQ_H
+#define _ARCH_ARM_HW_IRQ_H
+
+static inline void ack_bad_irq(int irq)
+{
+ extern unsigned long irq_err_count;
+ irq_err_count++;
+}
+
+/*
+ * Obsolete inline function for calling irq descriptor handlers.
+ */
+static inline void desc_handle_irq(unsigned int irq, struct irq_desc *desc)
+{
+ desc->handle_irq(irq, desc);
+}
+
+void set_irq_flags(unsigned int irq, unsigned int flags);
+
+#define IRQF_VALID (1 << 0)
+#define IRQF_PROBE (1 << 1)
+#define IRQF_NOAUTOEN (1 << 2)
+
+#endif
/*
- * linux/include/asm-arm/ide.h
+ * arch/arm/include/asm/ide.h
*
* Copyright (C) 1994-1996 Linus Torvalds & authors
*/
/*
- * linux/include/asm-arm/io.h
+ * arch/arm/include/asm/io.h
*
* Copyright (C) 1996-2000 Russell King
*
/*
* Now, pick up the machine-defined IO definitions
*/
-#include <asm/arch/io.h>
+#include <mach/io.h>
/*
* IO port access primitives
#ifndef __ASM_ARM_IRQ_H
#define __ASM_ARM_IRQ_H
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#ifndef irq_canonicalize
#define irq_canonicalize(i) (i)
/*
- * include/asm-arm/kprobes.h
+ * arch/arm/include/asm/kprobes.h
*
* Copyright (C) 2006, 2007 Motorola Inc.
*
/*
- * linux/include/asm-arm/leds.h
+ * arch/arm/include/asm/leds.h
*
* Copyright (C) 1998 Russell King
*
/*
- * linux/include/asm-arm/locks.h
+ * arch/arm/include/asm/locks.h
*
* Copyright (C) 2000 Russell King
*
/*
- * linux/include/asm-arm/mach/arch.h
+ * arch/arm/include/asm/mach/arch.h
*
* Copyright (C) 2000 Russell King
*
/*
- * linux/include/asm-arm/mach/dma.h
+ * arch/arm/include/asm/mach/dma.h
*
* Copyright (C) 1998-2000 Russell King
*
/*
- * linux/include/asm-arm/mach/flash.h
+ * arch/arm/include/asm/mach/flash.h
*
* Copyright (C) 2003 Russell King, All Rights Reserved.
*
/*
- * linux/include/asm-arm/mach/irda.h
+ * arch/arm/include/asm/mach/irda.h
*
* Copyright (C) 2004 Russell King.
*
/*
- * linux/include/asm-arm/mach/irq.h
+ * arch/arm/include/asm/mach/irq.h
*
* Copyright (C) 1995-2000 Russell King.
*
extern void init_FIQ(void);
extern int show_fiq_list(struct seq_file *, void *);
-/*
- * Obsolete inline function for calling irq descriptor handlers.
- */
-static inline void desc_handle_irq(unsigned int irq, struct irq_desc *desc)
-{
- desc->handle_irq(irq, desc);
-}
-
-void set_irq_flags(unsigned int irq, unsigned int flags);
-
-#define IRQF_VALID (1 << 0)
-#define IRQF_PROBE (1 << 1)
-#define IRQF_NOAUTOEN (1 << 2)
-
/*
* This is for easy migration, but should be changed in the source
*/
spin_unlock(&desc->lock); \
} while(0)
-extern unsigned long irq_err_count;
-static inline void ack_bad_irq(int irq)
-{
- irq_err_count++;
-}
-
#endif
/*
- * linux/include/asm-arm/map.h
+ * arch/arm/include/asm/map.h
*
* Copyright (C) 1999-2000 Russell King
*
/*
- * linux/include/asm-arm/mach/mmc.h
+ * arch/arm/include/asm/mach/mmc.h
*/
#ifndef ASMARM_MACH_MMC_H
#define ASMARM_MACH_MMC_H
/*
- * linux/include/asm-arm/mach/pci.h
+ * arch/arm/include/asm/mach/pci.h
*
* Copyright (C) 2000 Russell King
*
/*
- * linux/include/asm-arm/mach/serial_at91.h
+ * arch/arm/include/asm/mach/serial_at91.h
*
* Based on serial_sa1100.h by Nicolas Pitre
*
/*
- * linux/include/asm-arm/mach/serial_sa1100.h
+ * arch/arm/include/asm/mach/serial_sa1100.h
*
* Author: Nicolas Pitre
*
- * Moved to include/asm-arm/mach and changed lots, Russell King
+ * Moved and changed lots, Russell King
*
* Low level machine dependent UART functions.
*/
/*
- * linux/include/asm-arm/mach/time.h
+ * arch/arm/include/asm/mach/time.h
*
* Copyright (C) 2004 MontaVista Software, Inc.
*
/*
- * linux/include/asm-arm/mach/udc_pxa2xx.h
+ * arch/arm/include/asm/mach/udc_pxa2xx.h
*
* This supports machine-specific differences in how the PXA2xx
* USB Device Controller (UDC) is wired.
#ifndef _ASM_MC146818RTC_H
#define _ASM_MC146818RTC_H
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/io.h>
#ifndef RTC_PORT
/*
- * linux/include/asm-arm/memory.h
+ * arch/arm/include/asm/memory.h
*
* Copyright (C) 2000-2002 Russell King
* modification for nommu, Hyok S. Choi, 2004
#endif
#include <linux/compiler.h>
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
#include <asm/sizes.h>
#ifdef CONFIG_MMU
/*
- * linux/include/asm-arm/mmu_context.h
+ * arch/arm/include/asm/mmu_context.h
*
* Copyright (C) 1996 Russell King.
*
/*
- * linux/include/asm-arm/mmzone.h
+ * arch/arm/include/asm/mmzone.h
*
* 1999-12-29 Nicolas Pitre Created
*
*/
#define NODE_MEM_MAP(nid) (NODE_DATA(nid)->node_mem_map)
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
#endif
#ifndef __ARM_MTD_XIP_H__
#define __ARM_MTD_XIP_H__
-#include <asm/hardware.h>
-#include <asm/arch/mtd-xip.h>
+#include <mach/hardware.h>
+#include <mach/mtd-xip.h>
/* fill instruction prefetch */
#define xip_iprefetch() do { asm volatile (".rep 8; nop; .endr"); } while (0)
/*
- * include/asm-arm/mutex.h
+ * arch/arm/include/asm/mutex.h
*
* ARM optimized mutex locking primitives
*
/*
- * linux/include/asm-arm/page-nommu.h
+ * arch/arm/include/asm/page-nommu.h
*
* Copyright (C) 2004 Hyok S. Choi
*
/*
- * linux/include/asm-arm/page.h
+ * arch/arm/include/asm/page.h
*
* Copyright (C) 1995-2003 Russell King
*
/*
- * linux/include/asm-arm/param.h
+ * arch/arm/include/asm/param.h
*
* Copyright (C) 1995-1999 Russell King
*
/*
- * linux/include/asm-arm/parport.h: ARM-specific parport initialisation
+ * arch/arm/include/asm/parport.h: ARM-specific parport initialisation
*
* Copyright (C) 1999, 2000 Tim Waugh <tim@cyberelk.demon.co.uk>
*
#ifdef __KERNEL__
#include <asm-generic/pci-dma-compat.h>
-#include <asm/hardware.h> /* for PCIBIOS_MIN_* */
+#include <mach/hardware.h> /* for PCIBIOS_MIN_* */
#define pcibios_scan_all_fns(a, b) 0
/*
- * linux/include/asm-arm/pgalloc.h
+ * arch/arm/include/asm/pgalloc.h
*
* Copyright (C) 2000-2001 Russell King
*
/*
- * linux/include/asm-arm/pgtable-hwdef.h
+ * arch/arm/include/asm/pgtable-hwdef.h
*
* Copyright (C) 1995-2002 Russell King
*
/*
- * linux/include/asm-arm/pgtable-nommu.h
+ * arch/arm/include/asm/pgtable-nommu.h
*
* Copyright (C) 1995-2002 Russell King
* Copyright (C) 2004 Hyok S. Choi
/*
- * linux/include/asm-arm/pgtable.h
+ * arch/arm/include/asm/pgtable.h
*
* Copyright (C) 1995-2002 Russell King
*
#else
#include <asm/memory.h>
-#include <asm/arch/vmalloc.h>
+#include <mach/vmalloc.h>
#include <asm/pgtable-hwdef.h>
/*
/*
- * linux/include/asm-arm/posix_types.h
+ * arch/arm/include/asm/posix_types.h
*
* Copyright (C) 1996-1998 Russell King.
*
/*
- * linux/include/asm-arm/proc-fns.h
+ * arch/arm/include/asm/proc-fns.h
*
* Copyright (C) 1997-1999 Russell King
* Copyright (C) 2000 Deep Blue Solutions Ltd
/*
- * linux/include/asm-arm/processor.h
+ * arch/arm/include/asm/processor.h
*
* Copyright (C) 1995-1999 Russell King
*
/*
- * linux/include/asm-arm/procinfo.h
+ * arch/arm/include/asm/procinfo.h
*
* Copyright (C) 1996-1999 Russell King
*
/*
- * linux/include/asm-arm/ptrace.h
+ * arch/arm/include/asm/ptrace.h
*
* Copyright (C) 1996-2003 Russell King
*
/*
- * linux/include/asm-arm/serial.h
+ * arch/arm/include/asm/serial.h
*
* Copyright (C) 1996 Russell King.
*
/*
- * linux/include/asm-arm/smp.h
+ * arch/arm/include/asm/smp.h
*
* Copyright (C) 2004-2005 ARM Ltd.
*
#include <linux/cpumask.h>
#include <linux/thread_info.h>
-#include <asm/arch/smp.h>
+#include <mach/smp.h>
#ifndef CONFIG_SMP
-# error "<asm-arm/smp.h> included in non-SMP build"
+# error "<asm/smp.h> included in non-SMP build"
#endif
#define raw_smp_processor_id() (current_thread_info()->cpu)
/*
- * linux/include/asm-arm/therm.h: Definitions for Dallas Semiconductor
+ * arch/arm/include/asm/therm.h: Definitions for Dallas Semiconductor
* DS1620 thermometer driver (as used in the Rebel.com NetWinder)
*/
#ifndef __ASM_THERM_H
/*
- * linux/include/asm-arm/thread_info.h
+ * arch/arm/include/asm/thread_info.h
*
* Copyright (C) 2002 Russell King.
*
/*
* We use bit 30 of the preempt_count to indicate that kernel
- * preemption is occurring. See include/asm-arm/hardirq.h.
+ * preemption is occurring. See <asm/hardirq.h>.
*/
#define PREEMPT_ACTIVE 0x40000000
/*
- * linux/include/asm-arm/thread_notify.h
+ * arch/arm/include/asm/thread_notify.h
*
* Copyright (C) 2006 Russell King.
*
/*
- * linux/include/asm-arm/timex.h
+ * arch/arm/include/asm/timex.h
*
* Copyright (C) 1997,1998 Russell King
*
#ifndef _ASMARM_TIMEX_H
#define _ASMARM_TIMEX_H
-#include <asm/arch/timex.h>
+#include <mach/timex.h>
typedef unsigned long cycles_t;
/*
- * linux/include/asm-arm/tlb.h
+ * arch/arm/include/asm/tlb.h
*
* Copyright (C) 2002 Russell King
*
/*
- * linux/include/asm-arm/tlbflush.h
+ * arch/arm/include/asm/tlbflush.h
*
* Copyright (C) 1999-2003 Russell King
*
/*
- * linux/include/asm-arm/uaccess.h
+ * arch/arm/include/asm/uaccess.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * linux/include/asm-arm/unistd.h
+ * arch/arm/include/asm/unistd.h
*
* Copyright (C) 2001-2005 Russell King
*
/*
- * linux/include/asm-arm/vfp.h
+ * arch/arm/include/asm/vfp.h
*
* VFP register definitions.
* First, the standard VFP set.
/*
- * linux/include/asm-arm/vfpmacros.h
+ * arch/arm/include/asm/vfpmacros.h
*
* Assembler-only file containing VFP macros and register definitions.
*/
#ifndef ASMARM_VGA_H
#define ASMARM_VGA_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#define VGA_MAP_MEM(x,s) (PCIMEM_BASE + (x))
/*
- * linux/include/asm-arm/xor.h
+ * arch/arm/include/asm/xor.h
*
* Copyright (C) 2001 Russell King
*
#include <asm/ptrace.h>
#include <asm/thread_info.h>
#include <asm/asm-offsets.h>
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
/*
* We can't use hex constants here due to a bug in gas.
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/init.h>
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
#include <asm/thread_notify.h>
#include <asm/io.h>
#endif /* CONFIG_CPU_V6 */
#else
-#include <asm/arch/debug-macro.S>
+#include <mach/debug-macro.S>
#endif /* CONFIG_DEBUG_ICEDCC */
/*
#include <asm/dma.h>
#include <asm/ecard.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mmu_context.h>
#include <asm/mach/irq.h>
#include <asm/memory.h>
#include <asm/glue.h>
#include <asm/vfpmacros.h>
-#include <asm/arch/entry-macro.S>
+#include <mach/entry-macro.S>
#include <asm/thread_notify.h>
#include "entry-header.S"
#include <asm/unistd.h>
#include <asm/ftrace.h>
-#include <asm/arch/entry-macro.S>
+#include <mach/entry-macro.S>
#include "entry-header.S"
ldmfd sp!, {r4 - r7, r9, pc}
/*
- * Look in include/asm-arm/procinfo.h and arch/arm/kernel/arch.[ch] for
+ * Look in <asm/procinfo.h> and arch/arm/kernel/arch.[ch] for
* more information about the __proc_info and __arch_info structures.
*/
.long __proc_info_begin
#include <linux/init.h>
#include <asm/assembler.h>
-#include <asm/mach-types.h>
#include <asm/ptrace.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
#include <linux/proc_fs.h>
#include <asm/system.h>
+#include <asm/mach/irq.h>
#include <asm/mach/time.h>
/*
static volatile int hlt_counter;
-#include <asm/arch/system.h>
+#include <mach/system.h>
void disable_hlt(void)
{
* a 1:1 mapping for the physical address of the kernel.
*/
pgd = pgd_alloc(&init_mm);
- pmd = pmd_offset(pgd, PHYS_OFFSET);
+ pmd = pmd_offset(pgd + pgd_index(PHYS_OFFSET), PHYS_OFFSET);
*pmd = __pmd((PHYS_OFFSET & PGDIR_MASK) |
PMD_TYPE_SECT | PMD_SECT_AP_WRITE);
secondary_data.stack = NULL;
secondary_data.pgdir = 0;
- *pmd_offset(pgd, PHYS_OFFSET) = __pmd(0);
+ *pmd = __pmd(0);
pgd_free(&init_mm, pgd);
if (ret) {
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define CPSR2SPSR(rt) \
mrs rt, cpsr; \
* r2, r3 contains the zero-extended value
* lr corrupted
*
- * No other registers must be altered. (see include/asm-arm/uaccess.h
+ * No other registers must be altered. (see <asm/uaccess.h>
* for specific ASM register usage).
*
* Note that ADDR_LIMIT is either 0 or 0xc0000000.
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.Linsw_bad_alignment:
adr r0, .Linsw_bad_align_msg
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.Loutsw_bad_alignment:
adr r0, .Loutsw_bad_align_msg
* Outputs: r0 is the error code
* lr corrupted
*
- * No other registers must be altered. (see include/asm-arm/uaccess.h
+ * No other registers must be altered. (see <asm/uaccess.h>
* for specific ASM register usage).
*
* Note that ADDR_LIMIT is either 0 or 0xc0000000
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/aaed2000.h>
+#include <mach/aaed2000.h>
#include "core.h"
#include <linux/timex.h>
#include <linux/signal.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
/*
- * linux/include/asm-arm/arch-aaec2000/aaec2000.h
+ * arch/arm/mach-aaec2000/include/mach/aaec2000.h
*
* AAEC-2000 registers definition
*
/*
- * linux/include/asm-arm/arch-aaec2000/aaed2000.h
+ * arch/arm/mach-aaec2000/include/mach/aaed2000.h
*
* AAED-2000 specific bits definition
*
-/* linux/include/asm-arm/arch-aaec2000/debug-macro.S
+/* arch/arm/mach-aaec2000/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-aaec2000/dma.h
+ * arch/arm/mach-aaec2000/include/mach/dma.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
/*
- * linux/include/asm-arm/arch-aaec2000/entry-macro.S
+ * arch/arm/mach-aaec2000/include/mach/entry-macro.S
*
* Low-level IRQ helper for aaec-2000 based platforms
*
* published by the Free Software Foundation.
*
*/
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
.macro disable_fiq
.endm
/*
- * linux/include/asm-arm/arch-aaec2000/hardware.h
+ * arch/arm/mach-aaec2000/include/mach/hardware.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
-#include <asm/arch/aaec2000.h>
+#include <mach/aaec2000.h>
/* The kernel is loaded at physical address 0xf8000000.
* We map the IO space a bit after
/*
- * linux/include/asm-arm/arch-aaec2000/io.h
+ * arch/arm/mach-aaec2000/include/mach/io.h
*
* Copied from asm/arch/sa1100/io.h
*/
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-aaec2000/irqs.h
+ * arch/arm/mach-aaec2000/include/mach/irqs.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
/*
- * linux/include/asm-arm/arch-aaec2000/memory.h
+ * arch/arm/mach-aaec2000/include/mach/memory.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
/*
- * linux/include/asm-arm/arch-aaed2000/system.h
+ * arch/arm/mach-aaed2000/include/mach/system.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
/*
- * linux/include/asm-arm/arch-aaec2000/timex.h
+ * arch/arm/mach-aaec2000/include/mach/timex.h
*
* AAEC-2000 Architecture timex specification
*
/*
- * linux/include/asm-arm/arch-aaec2000/uncompress.h
+ * arch/arm/mach-aaec2000/include/mach/uncompress.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
/*
- * linux/include/asm-arm/arch-aaec2000/vmalloc.h
+ * arch/arm/mach-aaec2000/include/mach/vmalloc.h
*
* Copyright (c) 2005 Nicolas Bellido Y Ortega
*
help
Enable support for the DataFlash card.
-config MTD_NAND_AT91_BUSWIDTH_16
+config MTD_NAND_ATMEL_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
help
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/at91cap9.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/at91cap9.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
#include "clock.h"
#include <video/atmel_lcdc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91cap9.h>
-#include <asm/arch/at91cap9_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91cap9.h>
+#include <mach/at91cap9_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/at91rm9200.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_st.h>
+#include <mach/at91rm9200.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_st.h>
#include "generic.h"
#include "clock.h"
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <asm/mach/time.h>
-#include <asm/arch/at91_st.h>
+#include <mach/at91_st.h>
static unsigned long last_crtr;
static u32 irqmask;
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/at91sam9260.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/cpu.h>
+#include <mach/at91sam9260.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
#include "clock.h"
#include <linux/platform_device.h>
#include <linux/i2c-gpio.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/at91sam9260.h>
-#include <asm/arch/at91sam9260_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/cpu.h>
+#include <mach/at91sam9260.h>
+#include <mach/at91sam9260_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/at91sam9261.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/at91sam9261.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
#include "clock.h"
#include <linux/fb.h>
#include <video/atmel_lcdc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9261.h>
-#include <asm/arch/at91sam9261_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9261.h>
+#include <mach/at91sam9261_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/at91sam9263.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
#include "clock.h"
#include <linux/fb.h>
#include <video/atmel_lcdc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9263.h>
-#include <asm/arch/at91sam9263_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91sam9263_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <asm/mach/time.h>
-#include <asm/arch/at91_pit.h>
+#include <mach/at91_pit.h>
#define PIT_CPIV(x) ((x) & AT91_PIT_CPIV)
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/at91sam9rl.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/cpu.h>
+#include <mach/at91sam9rl.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
#include "clock.h"
#include <linux/fb.h>
#include <video/atmel_lcdc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9rl.h>
-#include <asm/arch/at91sam9rl_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9rl.h>
+#include <mach/at91sam9rl_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
* NAND / SmartMedia
* -------------------------------------------------------------------- */
-#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
#include <linux/init.h>
#include <linux/irq.h>
#include <asm/mach/arch.h>
-#include <asm/arch/at91x40.h>
-#include <asm/arch/at91_st.h>
-#include <asm/arch/timex.h>
+#include <mach/at91x40.h>
+#include <mach/at91_st.h>
+#include <mach/timex.h>
#include "generic.h"
/*
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach/time.h>
-#include <asm/arch/at91_tc.h>
+#include <mach/at91_tc.h>
/*
* 3 counter/timer units present.
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <video/atmel_lcdc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91cap9_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91cap9_matrix.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
// .rdy_pin = ... not connected
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/input.h>
#include <linux/gpio_keys.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
#include <linux/platform_device.h>
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#include "generic.h"
static void __init at91eb01_map_io(void)
#include <linux/module.h>
#include <linux/device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/mtd/physmap.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
#include <linux/input.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/spi/at73c213.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <video/atmel_lcdc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
.rdy_pin = AT91_PIN_PC15,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <video/atmel_lcdc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/spi/at73c213.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
#include "generic.h"
}
/* det_pin is not connected */
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <video/atmel_lcdc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91sam9_smc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9_smc.h>
#include "generic.h"
#include <linux/input.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/gpio_keys.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91_shdwc.h>
#include "generic.h"
return ek_nand_partition;
}
-static struct at91_nand_data __initdata ek_nand_data = {
+static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#include <linux/gpio_keys.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
#include "generic.h"
#include <linux/clk.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/cpu.h>
+#include <mach/hardware.h>
+#include <mach/at91_pmc.h>
+#include <mach/cpu.h>
#include "clock.h"
#include <linux/module.h>
#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/at91_pio.h>
-#include <asm/arch/gpio.h>
+#include <mach/hardware.h>
+#include <mach/at91_pio.h>
+#include <mach/gpio.h>
#include "generic.h"
/*
- * include/asm-arm/arch-at91/at91_adc.h
+ * arch/arm/mach-at91/include/mach/at91_adc.h
*
* Copyright (C) SAN People
*
/*
- * include/asm-arm/arch-at91/at91_aic.h
+ * arch/arm/mach-at91/include/mach/at91_aic.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_dbgu.h
+ * arch/arm/mach-at91/include/mach/at91_dbgu.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_mci.h
+ * arch/arm/mach-at91/include/mach/at91_mci.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_pio.h
+ * arch/arm/mach-at91/include/mach/at91_pio.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_pit.h
+ * arch/arm/mach-at91/include/mach/at91_pit.h
*
* Periodic Interval Timer (PIT) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91_pmc.h
+ * arch/arm/mach-at91/include/mach/at91_pmc.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_rstc.h
+ * arch/arm/mach-at91/include/mach/at91_rstc.h
*
* Reset Controller (RSTC) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91_rtc.h
+ * arch/arm/mach-at91/include/mach/at91_rtc.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_rtt.h
+ * arch/arm/mach-at91/include/mach/at91_rtt.h
*
* Real-time Timer (RTT) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91_shdwc.h
+ * arch/arm/mach-at91/include/mach/at91_shdwc.h
*
* Shutdown Controller (SHDWC) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91_spi.h
+ * arch/arm/mach-at91/include/mach/at91_spi.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_ssc.h
+ * arch/arm/mach-at91/include/mach/at91_ssc.h
*
* Copyright (C) SAN People
*
/*
- * include/asm-arm/arch-at91/at91_st.h
+ * arch/arm/mach-at91/include/mach/at91_st.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_tc.h
+ * arch/arm/mach-at91/include/mach/at91_tc.h
*
* Copyright (C) SAN People
*
/*
- * include/asm-arm/arch-at91/at91_twi.h
+ * arch/arm/mach-at91/include/mach/at91_twi.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91_wdt.h
+ * arch/arm/mach-at91/include/mach/at91_wdt.h
*
* Watchdog Timer (WDT) - System peripherals regsters.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91cap9.h
+ * arch/arm/mach-at91/include/mach/at91cap9.h
*
* Copyright (C) 2007 Stelian Pop <stelian.pop@leadtechdesign.com>
* Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
/*
- * include/asm-arm/arch-at91/at91cap9_ddrsdr.h
+ * arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h
*
* DDR/SDR Controller (DDRSDRC) - System peripherals registers.
* Based on AT91CAP9 datasheet revision B.
/*
- * include/asm-arm/arch-at91/at91cap9_matrix.h
+ * arch/arm/mach-at91/include/mach/at91cap9_matrix.h
*
* Copyright (C) 2007 Stelian Pop <stelian.pop@leadtechdesign.com>
* Copyright (C) 2007 Lead Tech Design <www.leadtechdesign.com>
/*
- * include/asm-arm/arch-at91/at91rm9200.h
+ * arch/arm/mach-at91/include/mach/at91rm9200.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91rm9200_emac.h
+ * arch/arm/mach-at91/include/mach/at91rm9200_emac.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91rm9200_mc.h
+ * arch/arm/mach-at91/include/mach/at91rm9200_mc.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
/*
- * include/asm-arm/arch-at91/at91sam9260.h
+ * arch/arm/mach-at91/include/mach/at91sam9260.h
*
* (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-at91/at91sam9260_matrix.h
+ * arch/arm/mach-at91/include/mach/at91sam9260_matrix.h
*
* Memory Controllers (MATRIX, EBI) - System peripherals registers.
* Based on AT91SAM9260 datasheet revision B.
/*
- * include/asm-arm/arch-at91/at91sam9261.h
+ * arch/arm/mach-at91/include/mach/at91sam9261.h
*
* Copyright (C) SAN People
*
/*
- * include/asm-arm/arch-at91/at91sam9261_matrix.h
+ * arch/arm/mach-at91/include/mach/at91sam9261_matrix.h
*
* Memory Controllers (MATRIX, EBI) - System peripherals registers.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91sam9263.h
+ * arch/arm/mach-at91/include/mach/at91sam9263.h
*
* (C) 2007 Atmel Corporation.
*
/*
- * include/asm-arm/arch-at91/at91sam9263_matrix.h
+ * arch/arm/mach-at91/include/mach/at91sam9263_matrix.h
*
* Copyright (C) 2006 Atmel Corporation.
*
/*
- * include/asm-arm/arch-at91/at91sam9_sdramc.h
+ * arch/arm/mach-at91/include/mach/at91sam9_sdramc.h
*
* SDRAM Controllers (SDRAMC) - System peripherals registers.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91sam9_smc.h
+ * arch/arm/mach-at91/include/mach/at91sam9_smc.h
*
* Static Memory Controllers (SMC) - System peripherals registers.
* Based on AT91SAM9261 datasheet revision D.
/*
- * include/asm-arm/arch-at91/at91sam9260.h
+ * arch/arm/mach-at91/include/mach/at91sam9260.h
*
* Copyright (C) 2007 Atmel Corporation
*
/*
- * include/asm-arm/arch-at91/at91sam9rl_matrix.h
+ * arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h
*
* Copyright (C) 2007 Atmel Corporation
*
/*
- * include/asm-arm/arch-at91/at91x40.h
+ * arch/arm/mach-at91/include/mach/at91x40.h
*
* (C) Copyright 2007, Greg Ungerer <gerg@snapgear.com>
*
/*
- * include/asm-arm/arch-at91/board.h
+ * arch/arm/mach-at91/include/mach/board.h
*
* Copyright (C) 2005 HP Labs
*
/*
- * include/asm-arm/arch-at91/cpu.h
+ * arch/arm/mach-at91/include/mach/cpu.h
*
* Copyright (C) 2006 SAN People
*
#ifndef __ASM_ARCH_CPU_H
#define __ASM_ARCH_CPU_H
-#include <asm/hardware.h>
-#include <asm/arch/at91_dbgu.h>
+#include <mach/hardware.h>
+#include <mach/at91_dbgu.h>
#define ARCH_ID_AT91RM9200 0x09290780
/*
- * include/asm-arm/arch-at91/debug-macro.S
+ * arch/arm/mach-at91/include/mach/debug-macro.S
*
* Copyright (C) 2003-2005 SAN People
*
*
*/
-#include <asm/hardware.h>
-#include <asm/arch/at91_dbgu.h>
+#include <mach/hardware.h>
+#include <mach/at91_dbgu.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-at91/dma.h
+ * arch/arm/mach-at91/include/mach/dma.h
*
* Copyright (C) 2003 SAN People
*
/*
- * include/asm-arm/arch-at91/entry-macro.S
+ * arch/arm/mach-at91/include/mach/entry-macro.S
*
* Copyright (C) 2003-2005 SAN People
*
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/at91_aic.h>
+#include <mach/hardware.h>
+#include <mach/at91_aic.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-at91/gpio.h
+ * arch/arm/mach-at91/include/mach/gpio.h
*
* Copyright (C) 2005 HP Labs
*
/*
- * include/asm-arm/arch-at91/hardware.h
+ * arch/arm/mach-at91/include/mach/hardware.h
*
* Copyright (C) 2003 SAN People
* Copyright (C) 2003 ATMEL
#include <asm/sizes.h>
#if defined(CONFIG_ARCH_AT91RM9200)
-#include <asm/arch/at91rm9200.h>
+#include <mach/at91rm9200.h>
#elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
-#include <asm/arch/at91sam9260.h>
+#include <mach/at91sam9260.h>
#elif defined(CONFIG_ARCH_AT91SAM9261)
-#include <asm/arch/at91sam9261.h>
+#include <mach/at91sam9261.h>
#elif defined(CONFIG_ARCH_AT91SAM9263)
-#include <asm/arch/at91sam9263.h>
+#include <mach/at91sam9263.h>
#elif defined(CONFIG_ARCH_AT91SAM9RL)
-#include <asm/arch/at91sam9rl.h>
+#include <mach/at91sam9rl.h>
#elif defined(CONFIG_ARCH_AT91CAP9)
-#include <asm/arch/at91cap9.h>
+#include <mach/at91cap9.h>
#elif defined(CONFIG_ARCH_AT91X40)
-#include <asm/arch/at91x40.h>
+#include <mach/at91x40.h>
#else
#error "Unsupported AT91 processor"
#endif
/*
- * include/asm-arm/arch-at91/io.h
+ * arch/arm/mach-at91/include/mach/io.h
*
* Copyright (C) 2003 SAN People
*
/*
- * include/asm-arm/arch-at91/irqs.h
+ * arch/arm/mach-at91/include/mach/irqs.h
*
* Copyright (C) 2004 SAN People
*
#define __ASM_ARCH_IRQS_H
#include <asm/io.h>
-#include <asm/arch/at91_aic.h>
+#include <mach/at91_aic.h>
#define NR_AIC_IRQS 32
/*
- * include/asm-arm/arch-at91/memory.h
+ * arch/arm/mach-at91/include/mach/memory.h
*
* Copyright (C) 2004 SAN People
*
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define PHYS_OFFSET (AT91_SDRAM_BASE)
/*
- * include/asm-arm/arch-at91/system.h
+ * arch/arm/mach-at91/include/mach/system.h
*
* Copyright (C) 2003 SAN People
*
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
-#include <asm/arch/at91_st.h>
-#include <asm/arch/at91_dbgu.h>
+#include <mach/hardware.h>
+#include <mach/at91_st.h>
+#include <mach/at91_dbgu.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-at91/timex.h
+ * arch/arm/mach-at91/include/mach/timex.h
*
* Copyright (C) 2003 SAN People
*
#ifndef __ASM_ARCH_TIMEX_H
#define __ASM_ARCH_TIMEX_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#if defined(CONFIG_ARCH_AT91RM9200)
/*
- * include/asm-arm/arch-at91/uncompress.h
+ * arch/arm/mach-at91/include/mach/uncompress.h
*
* Copyright (C) 2003 SAN People
*
/*
- * include/asm-arm/arch-at91/vmalloc.h
+ * arch/arm/mach-at91/include/mach/vmalloc.h
*
* Copyright (C) 2003 SAN People
*
#include <linux/mm.h>
#include <linux/types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/mach/arch.h>
#include <linux/module.h>
#include <linux/init.h>
-#include <asm/mach-types.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
/* ------------------------------------------------------------------------- */
#include <asm/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <asm/mach-types.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/cpu.h>
+#include <mach/at91_pmc.h>
+#include <mach/gpio.h>
+#include <mach/cpu.h>
#include "generic.h"
#ifdef CONFIG_ARCH_AT91RM9200
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/at91rm9200_mc.h>
/*
* The AT91RM9200 goes into self-refresh mode with this command, and will
#define sdram_selfrefresh_disable() do {} while (0)
#elif defined(CONFIG_ARCH_AT91CAP9)
-#include <asm/arch/at91cap9_ddrsdr.h>
+#include <mach/at91cap9_ddrsdr.h>
static u32 saved_lpr;
#define sdram_selfrefresh_disable() at91_sys_write(AT91_DDRSDRC_LPR, saved_lpr)
#else
-#include <asm/arch/at91sam9_sdramc.h>
+#include <mach/at91sam9_sdramc.h>
#ifdef CONFIG_ARCH_AT91SAM9263
/*
*/
#if defined(AT91_SHDWC)
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/at91_shdwc.h>
+#include <mach/at91_rstc.h>
+#include <mach/at91_shdwc.h>
static void __init show_reset_status(void)
{
#include <linux/string.h>
#include <linux/mm.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/sizes.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/page.h>
#include <asm/mach/map.h>
-#include <asm/arch/autcpu12.h>
+#include <mach/autcpu12.h>
#include "common.h"
#include <linux/string.h>
#include <linux/mm.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <linux/kernel.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/sizes.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/sizes.h>
#include <linux/init.h>
#include <linux/initrd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
-/* linux/include/asm-arm/arch-clps711x/debug-macro.S
+/* arch/arm/mach-clps711x/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-clps711x/dma.h
+ * arch/arm/mach-clps711x/include/mach/dma.h
*
* Copyright (C) 1997,1998 Russell King
*
/*
- * include/asm-arm/arch-clps711x/entry-macro.S
+ * arch/arm/mach-clps711x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for CLPS711X-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/clps7111.h>
.macro disable_fiq
/*
- * linux/include/asm-arm/arch-clps711x/hardware.h
+ * arch/arm/mach-clps711x/include/mach/hardware.h
*
* This file contains the hardware definitions of the Prospector P720T.
*
/*
- * linux/include/asm-arm/arch-clps711x/io.h
+ * arch/arm/mach-clps711x/include/mach/io.h
*
* Copyright (C) 1999 ARM Limited
*
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-clps711x/irqs.h
+ * arch/arm/mach-clps711x/include/mach/irqs.h
*
* Copyright (C) 2000 Deep Blue Solutions Ltd.
*
/*
- * linux/include/asm-arm/arch-clps711x/memory.h
+ * arch/arm/mach-clps711x/include/mach/memory.h
*
* Copyright (C) 1999 ARM Limited
*
/*
- * linux/include/asm-arm/arch-clps711x/syspld.h
+ * arch/arm/mach-clps711x/include/mach/syspld.h
*
* System Control PLD register definitions.
*
/*
- * linux/include/asm-arm/arch-clps711x/system.h
+ * arch/arm/mach-clps711x/include/mach/system.h
*
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/clps7111.h>
#include <asm/io.h>
/*
- * linux/include/asm-arm/arch-clps711x/time.h
+ * arch/arm/mach-clps711x/include/mach/time.h
*
* Copyright (C) 2000 Deep Blue Solutions Ltd.
*
/*
- * linux/include/asm-arm/arch-clps711x/timex.h
+ * arch/arm/mach-clps711x/include/mach/timex.h
*
* Prospector 720T architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-clps711x/uncompress.h
+ * arch/arm/mach-clps711x/include/mach/uncompress.h
*
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <asm/arch/io.h>
-#include <asm/hardware.h>
+#include <mach/io.h>
+#include <mach/hardware.h>
#include <asm/hardware/clps7111.h>
#undef CLPS7111_BASE
/*
- * linux/include/asm-arm/arch-clps711x/vmalloc.h
+ * arch/arm/mach-clps711x/include/mach/vmalloc.h
*
* Copyright (C) 2000 Deep Blue Solutions Ltd.
*
#include <linux/list.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/bootmem.h>
#include <asm/sizes.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/mach/map.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <linux/string.h>
#include <linux/mm.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/syspld.h>
+#include <mach/syspld.h>
#include "common.h"
#include <linux/irq.h>
#include <linux/sched.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/leds.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iomd.h>
#include <asm/io.h>
#include <asm/irq.h>
-/* linux/include/asm-arm/arch-cl7500/debug-macro.S
+/* arch/arm/mach-clps7500/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-cl7500/dma.h
+ * arch/arm/mach-clps7500/include/mach/dma.h
*
* Copyright (C) 1999 Nexus Electronics Ltd.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/entry-macro-iomd.S>
.equ ioc_base_high, IOC_BASE & 0xff000000
/*
- * linux/include/asm-arm/arch-cl7500/hardware.h
+ * arch/arm/mach-clps7500/include/mach/hardware.h
*
* Copyright (C) 1996-1999 Russell King.
* Copyright (C) 1999 Nexus Electronics Ltd.
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
#include <asm/hardware/iomd.h>
#ifdef __ASSEMBLY__
/*
- * linux/include/asm-arm/arch-cl7500/io.h
- * from linux/include/asm-arm/arch-rpc/io.h
+ * arch/arm/mach-clps7500/include/mach/io.h
+ * from arch/arm/mach-rpc/include/mach/io.h
*
* Copyright (C) 1997 Russell King
*
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * include/asm-arm/arch-cl7500/irq.h
+ * arch/arm/mach-clps7500/include/mach/irq.h
*
* Copyright (C) 1996 Russell King
* Copyright (C) 1999, 2001 Nexus Electronics Ltd.
/*
- * linux/include/asm-arm/arch-cl7500/irqs.h
+ * arch/arm/mach-clps7500/include/mach/irqs.h
*
* Copyright (C) 1999 Nexus Electronics Ltd
*/
/*
- * linux/include/asm-arm/arch-cl7500/memory.h
+ * arch/arm/mach-clps7500/include/mach/memory.h
*
* Copyright (c) 1996,1997,1998 Russell King.
*
/*
- * linux/include/asm-arm/arch-cl7500/system.h
+ * arch/arm/mach-clps7500/include/mach/system.h
*
* Copyright (c) 1999 Nexus Electronics Ltd.
*/
/*
- * linux/include/asm-arm/arch-cl7500/timex.h
+ * arch/arm/mach-clps7500/include/mach/timex.h
*
* CL7500 architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-cl7500/uncompress.h
+ * arch/arm/mach-clps7500/include/mach/uncompress.h
*
* Copyright (C) 1999, 2000 Nexus Electronics Ltd.
*/
/*
- * linux/include/asm-arm/arch-cl7500/vmalloc.h
+ * arch/arm/mach-clps7500/include/mach/vmalloc.h
*/
#define VMALLOC_END (PAGE_OFFSET + 0x1c000000)
#include <asm/setup.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/common.h>
+#include <mach/common.h>
/* other misc. init functions */
void __init davinci_psc_init(void);
#include <linux/mutex.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/psc.h>
+#include <mach/psc.h>
#include "clock.h"
/* PLL/Reset register offsets */
#include <linux/irq.h>
#include <linux/bitops.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/gpio.h>
+#include <mach/irqs.h>
+#include <mach/hardware.h>
+#include <mach/gpio.h>
#include <asm/mach/irq.h>
/*
- * include/asm-arm/arch-davinci/clock.h
+ * arch/arm/mach-davinci/include/mach/clock.h
*
* Clock control driver for DaVinci - header file
*
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <asm/arch/io.h>
-#include <asm/arch/irqs.h>
+#include <mach/io.h>
+#include <mach/irqs.h>
.macro disable_fiq
.endm
#define __DAVINCI_GPIO_H
#include <linux/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* basic gpio routines
#ifndef __ASM_ARCH_SERIAL_H
#define __ASM_ARCH_SERIAL_H
-#include <asm/arch/io.h>
+#include <mach/io.h>
#define DAVINCI_UART0_BASE (IO_PHYS + 0x20000)
#define DAVINCI_UART1_BASE (IO_PHYS + 0x20400)
#define __ASM_ARCH_SYSTEM_H
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
extern void davinci_watchdog_reset(void);
#include <linux/types.h>
#include <linux/serial_reg.h>
-#include <asm/arch/serial.h>
+#include <mach/serial.h>
/* PORT_16C550A, in polled non-fifo mode */
* or implied.
*/
#include <asm/memory.h>
-#include <asm/arch/io.h>
+#include <mach/io.h>
/* Allow vmalloc range until the IO virtual range minus a 2M "hole" */
#define VMALLOC_END (IO_VIRT - (2<<20))
#include <asm/memory.h>
#include <asm/mach/map.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
extern void davinci_check_revision(void);
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
#include <linux/io.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
/* System control register offsets */
#define PINMUX0 0x00
#include <linux/init.h>
#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/psc.h>
-#include <asm/arch/mux.h>
+#include <mach/hardware.h>
+#include <mach/psc.h>
+#include <mach/mux.h>
/* PSC register offsets */
#define EPCPR 0x070
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/arch/serial.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/serial.h>
+#include <mach/irqs.h>
#define UART_DAVINCI_PWREMU 0x0c
#include <linux/spinlock.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <asm/errno.h>
-#include <asm/arch/io.h>
+#include <mach/io.h>
static struct clock_event_device clockevent_davinci;
#include <linux/serial_8250.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/setup.h>
-/* linux/include/asm-arm/arch-ebsa110/debug-macro.S
+/* arch/arm/mach-ebsa110/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-ebsa110/dma.h
+ * arch/arm/mach-ebsa110/include/mach/dma.h
*
* Copyright (C) 1997,1998 Russell King
*
/*
- * include/asm-arm/arch-ebsa110/entry-macro.S
+ * arch/arm/mach-ebsa110/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for ebsa110 platform.
*
/*
- * linux/include/asm-arm/arch-ebsa110/hardware.h
+ * arch/arm/mach-ebsa110/include/mach/hardware.h
*
* Copyright (C) 1996-2000 Russell King.
*
/*
- * linux/include/asm-arm/arch-ebsa110/io.h
+ * arch/arm/mach-ebsa110/include/mach/io.h
*
* Copyright (C) 1997,1998 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa110/irqs.h
+ * arch/arm/mach-ebsa110/include/mach/irqs.h
*
* Copyright (C) 1996 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa110/memory.h
+ * arch/arm/mach-ebsa110/include/mach/memory.h
*
* Copyright (C) 1996-1999 Russell King.
*
/*
- * linux/include/asm-arm/arch-ebsa110/system.h
+ * arch/arm/mach-ebsa110/include/mach/system.h
*
* Copyright (C) 1996-2000 Russell King.
*
/*
- * linux/include/asm-arm/arch-ebsa110/timex.h
+ * arch/arm/mach-ebsa110/include/mach/timex.h
*
* Copyright (C) 1997, 1998 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa110/uncompress.h
+ * arch/arm/mach-ebsa110/include/mach/uncompress.h
*
* Copyright (C) 1996,1997,1998 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa110/vmalloc.h
+ * arch/arm/mach-ebsa110/include/mach/vmalloc.h
*
* Copyright (C) 1998 Russell King
*
#include <linux/kernel.h>
#include <linux/types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/page.h>
#include <linux/spinlock.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <asm/mach-types.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/module.h>
#include <linux/string.h>
#include <asm/div64.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
struct clk {
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/tlbflush.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#include <asm/hardware/vic.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/module.h>
#include <linux/seq_file.h>
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
#include <asm/io.h>
#include <asm/gpio.h>
/*
- * linux/include/asm-arm/arch-ep93xx/debug-macro.S
+ * arch/arm/mach-ep93xx/include/mach/debug-macro.S
* Debugging macro include header
*
* Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/dma.h
+ */
/*
- * linux/include/asm-arm/arch-ep93xx/entry-macro.S
+ * arch/arm/mach-ep93xx/include/mach/entry-macro.S
* IRQ demultiplexing for EP93xx
*
* Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
.macro disable_fiq
.endm
/*
- * linux/include/asm-arm/arch-ep93xx/ep93xx-regs.h
+ * arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
*/
#ifndef __ASM_ARCH_EP93XX_REGS_H
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/gesbc9312.h
+ */
/*
- * linux/include/asm-arm/arch-ep93xx/gpio.h
+ * arch/arm/mach-ep93xx/include/mach/gpio.h
*/
#ifndef __ASM_ARCH_GPIO_H
/*
- * linux/include/asm-arm/arch-ep93xx/hardware.h
+ * arch/arm/mach-ep93xx/include/mach/hardware.h
*/
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
#include "ep93xx-regs.h"
#include "gesbc9312.h"
#include "ts72xx.h"
+
+#endif
/*
- * linux/include/asm-arm/arch-ep93xx/io.h
+ * arch/arm/mach-ep93xx/include/mach/io.h
*/
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-ep93xx/irqs.h
+ * arch/arm/mach-ep93xx/include/mach/irqs.h
*/
#ifndef __ASM_ARCH_IRQS_H
/*
- * include/asm-arm/arch-kirkwood/memory.h
+ * arch/arm/mach-ep93xx/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
#define PHYS_OFFSET UL(0x00000000)
-#define __virt_to_bus(x) __virt_to_phys(x)
#define __bus_to_virt(x) __phys_to_virt(x)
+#define __virt_to_bus(x) __virt_to_phys(x)
#endif
/*
- * linux/include/asm-arm/arch-ep93xx/platform.h
+ * arch/arm/mach-ep93xx/include/mach/platform.h
*/
#ifndef __ASSEMBLY__
/*
- * linux/include/asm-arm/arch-ep93xx/system.h
+ * arch/arm/mach-ep93xx/include/mach/system.h
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static inline void arch_idle(void)
{
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/timex.h
+ */
+
+#define CLOCK_TICK_RATE 983040
/*
- * linux/include/asm-arm/arch-ep93xx/ts72xx.h
+ * arch/arm/mach-ep93xx/include/mach/ts72xx.h
*/
/*
/*
- * linux/include/asm-arm/arch-ep93xx/uncompress.h
+ * arch/arm/mach-ep93xx/include/mach/uncompress.h
*
* Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
*
* your option) any later version.
*/
-#include <asm/arch/ep93xx-regs.h>
+#include <mach/ep93xx-regs.h>
static unsigned char __raw_readb(unsigned int ptr)
{
--- /dev/null
+/*
+ * arch/arm/mach-ep93xx/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe800000
#include <linux/mtd/physmap.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <linux/platform_device.h>
#include <linux/m48t86.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/init.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
#include <asm/system.h>
-/* linux/include/asm-arm/arch-ebsa285/debug-macro.S
+/* arch/arm/mach-footbridge/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-ebsa285/dma.h
+ * arch/arm/mach-footbridge/include/mach/dma.h
*
* Architecture DMA routines
*
/*
- * include/asm-arm/arch-ebsa285/entry-macro.S
+ * arch/arm/mach-footbridge/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for footbridge-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
#include <asm/hardware/dec21285.h>
.equ dc21285_high, ARMCSR_BASE & 0xff000000
/*
- * linux/include/asm-arm/arch-ebsa285/hardware.h
+ * arch/arm/mach-footbridge/include/mach/hardware.h
*
* Copyright (C) 1998-1999 Russell King.
*
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
/* Virtual Physical Size
* 0xff800000 0x40000000 1MB X-Bus
/*
- * linux/include/asm-arm/arch-ebsa285/io.h
+ * arch/arm/mach-footbridge/include/mach/io.h
*
* Copyright (C) 1997-1999 Russell King
*
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffff
/*
- * linux/include/asm-arm/arch-ebsa285/irqs.h
+ * arch/arm/mach-footbridge/include/mach/irqs.h
*
* Copyright (C) 1998 Russell King
* Copyright (C) 1998 Phil Blundell
/*
- * linux/include/asm-arm/arch-ebsa285/memory.h
+ * arch/arm/mach-footbridge/include/mach/memory.h
*
* Copyright (C) 1996-1999 Russell King.
*
/*
- * linux/include/asm-arm/arch-ebsa285/system.h
+ * arch/arm/mach-footbridge/include/mach/system.h
*
* Copyright (C) 1996-1999 Russell King.
*
*/
#include <asm/hardware/dec21285.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
/*
- * linux/include/asm-arm/arch-ebsa285/timex.h
+ * arch/arm/mach-footbridge/include/mach/timex.h
*
* Copyright (C) 1998 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa285/uncompress.h
+ * arch/arm/mach-footbridge/include/mach/uncompress.h
*
* Copyright (C) 1996-1999 Russell King
*
/*
- * linux/include/asm-arm/arch-ebsa285/vmalloc.h
+ * arch/arm/mach-footbridge/include/mach/vmalloc.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/dec21285.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <linux/init.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/mach-types.h>
#include <asm/system.h>
/*
- * linux/include/asm-arm/arch-ebsa285/time.h
+ * arch/arm/mach-footbridge/include/mach/time.h
*
* Copyright (C) 1998 Russell King.
* Copyright (C) 1998 Phil Blundell
#include <linux/mc146818rtc.h>
#include <linux/bcd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach/time.h>
#include <asm/pgtable.h>
#include <asm/dma.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/mach/dma.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <asm/types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include "common.h"
#include <linux/interrupt.h>
#include <linux/module.h>
#include <asm/types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <linux/device.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/mach/arch.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "common.h"
MACHINE_START(H7201, "Hynix GMS30C7201")
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/mach/arch.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "common.h"
static struct resource cirrus_resources[] = {
/*
- * linux/include/asm-arm/arch-h720x/boards.h
+ * arch/arm/mach-h720x/include/mach/boards.h
*
* Copyright (C) 2003 Thomas Gleixner <tglx@linutronix.de>
* (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
-/* linux/include/asm-arm/arch-h720x/debug-macro.S
+/* arch/arm/mach-h720x/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-h720x/dma.h
+ * arch/arm/mach-h720x/include/mach/dma.h
*
* Architecture DMA routes
*
/*
- * include/asm-arm/arch-h720x/entry-macro.S
+ * arch/arm/mach-h720x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Hynix HMS720x based platforms
*
/*
- * linux/include/asm-arm/arch-h720x/h7201-regs.h
+ * arch/arm/mach-h720x/include/mach/h7201-regs.h
*
* Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
* (C) 2003 Thomas Gleixner <tglx@linutronix.de>
/*
- * linux/include/asm-arm/arch-h720x/h7202-regs.h
+ * arch/arm/mach-h720x/include/mach/h7202-regs.h
*
* Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
* (C) 2003 Thomas Gleixner <tglx@linutronix.de>
/*
- * linux/include/asm-arm/arch-h720x/hardware.h
+ * arch/arm/mach-h720x/include/mach/hardware.h
*
* Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
* (C) 2003 Thomas Gleixner <tglx@linutronix.de>
/*
- * linux/include/asm-arm/arch-h720x/io.h
+ * arch/arm/mach-h720x/include/mach/io.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
* Changelog:
*
* 09-19-2001 JJKIM
- * Created from linux/include/asm-arm/arch-l7200/io.h
+ * Created from arch/arm/mach-l7200/include/mach/io.h
*
* 03-27-2003 Robert Schwebel <r.schwebel@pengutronix.de>:
* re-unified header files for h720x
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-h720x/irqs.h
+ * arch/arm/mach-h720x/include/mach/irqs.h
*
* Copyright (C) 2000 Jungjun Kim
* (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
/*
- * linux/include/asm-arm/arch-h720x/memory.h
+ * arch/arm/mach-h720x/include/mach/memory.h
*
* Copyright (c) 2000 Jungjun Kim
*
/*
- * linux/include/asm-arm/arch-h720x/system.h
+ * arch/arm/mach-h720x/include/mach/system.h
*
* Copyright (C) 2001-2002 Jungjun Kim, Hynix Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- * linux/include/asm-arm/arch-h720x/system.h
+ * arch/arm/mach-h720x/include/mach/system.h
*
*/
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-h720x/timex.h
+ * arch/arm/mach-h720x/include/mach/timex.h
* Copyright (C) 2000 Jungjun Kim, Hynix Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify
/*
- * linux/include/asm-arm/arch-h720x/uncompress.h
+ * arch/arm/mach-h720x/include/mach/uncompress.h
*
* Copyright (C) 2001-2002 Jungjun Kim
*/
#ifndef __ASM_ARCH_UNCOMPRESS_H
#define __ASM_ARCH_UNCOMPRESS_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define LSR 0x14
#define TEMPTY 0x40
/*
- * linux/include/asm-arm/arch-h720x/vmalloc.h
+ * arch/arm/mach-h720x/include/mach/vmalloc.h
*/
#ifndef __ARCH_ARM_VMALLOC_H
#include <linux/err.h>
#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
+#include <mach/imx-regs.h>
/*
* Very simple approach: We can't disable clocks, so we do
return clk;
}
+EXPORT_SYMBOL(clk_get);
void clk_put(struct clk *clk)
{
}
+EXPORT_SYMBOL(clk_put);
int clk_enable(struct clk *clk)
{
return 0;
}
+EXPORT_SYMBOL(clk_enable);
void clk_disable(struct clk *clk)
{
}
+EXPORT_SYMBOL(clk_disable);
unsigned long clk_get_rate(struct clk *clk)
{
return clk->get_rate();
}
+EXPORT_SYMBOL(clk_get_rate);
int imx_clocks_init(void)
{
#include <linux/err.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "generic.h"
#include <asm/system.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
-#include <asm/arch/imx-dma.h>
+#include <mach/imx-dma.h>
struct imx_dma_channel imx_dma_channels[IMX_DMA_CHANNELS];
#include <linux/string.h>
#include <asm/errno.h>
-#include <asm/arch/imxfb.h>
-#include <asm/hardware.h>
-#include <asm/arch/imx-regs.h>
+#include <mach/imxfb.h>
+#include <mach/hardware.h>
+#include <mach/imx-regs.h>
#include <asm/mach/map.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/gpio.h>
+#include <mach/mmc.h>
+#include <mach/gpio.h>
unsigned long imx_gpio_alloc_map[(GPIO_PORT_MAX + 1) * 32 / BITS_PER_LONG];
{
memcpy(&imx_fb_info,hard_imx_fb_info,sizeof(struct imxfb_mach_info));
}
-EXPORT_SYMBOL(set_imx_fb_info);
static struct resource imxfb_resources[] = {
[0] = {
-/* linux/include/asm-arm/arch-imx/debug-macro.S
+/* arch/arm/mach-imx/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * include/asm-arm/arch-imx/entry-macro.S
+ * arch/arm/mach-imx/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for iMX-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.macro disable_fiq
.endm
#ifndef _IMX_GPIO_H
-#include <asm/arch/imx-regs.h>
+#include <mach/imx-regs.h>
#define IMX_GPIO_ALLOC_MODE_NORMAL 0
#define IMX_GPIO_ALLOC_MODE_NO_ALLOC 1
/*
- * linux/include/asm-arm/arch-imx/hardware.h
+ * arch/arm/mach-imx/include/mach/hardware.h
*
* Copyright (C) 1999 ARM Limited.
*
/*
- * linux/include/asm-arm/arch-imxads/io.h
+ * arch/arm/mach-imxads/include/mach/io.h
*
* Copyright (C) 1999 ARM Limited
*
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-imxads/irqs.h
+ * arch/arm/mach-imxads/include/mach/irqs.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
#define __ARM_IRQS_H__
/* Use the imx definitions */
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* IMX Interrupt numbers
/*
- * linux/include/asm-arm/arch-imx/memory.h
+ * arch/arm/mach-imx/include/mach/memory.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2002 Shane Nay (shane@minirl.com)
/*
- * linux/include/asm-arm/arch-imx/mx1ads.h
+ * arch/arm/mach-imx/include/mach/mx1ads.h
*
* Copyright (C) 2004 Robert Schwebel, Pengutronix
*
/*
- * include/asm-arm/arch-imx/spi_imx.h
+ * arch/arm/mach-imx/include/mach/spi_imx.h
*
* Copyright (C) 2006 SWAPP
* Andrea Paterniani <a.paterniani@swapp-eng.it>
*
* Initial version inspired by:
- * linux-2.6.17-rc3-mm1/include/asm-arm/arch-pxa/pxa2xx_spi.h
+ * linux-2.6.17-rc3-mm1/arch/arm/mach-pxa/include/mach/pxa2xx_spi.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
/*
- * linux/include/asm-arm/arch-imxads/system.h
+ * arch/arm/mach-imxads/include/mach/system.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
/*
- * linux/include/asm-arm/arch-imxads/uncompress.h
+ * arch/arm/mach-imxads/include/mach/uncompress.h
*
*
*
/*
- * linux/include/asm-arm/arch-imx/vmalloc.h
+ * arch/arm/mach-imx/include/mach/vmalloc.h
*
* Copyright (C) 2000 Russell King.
*
#include <linux/list.h>
#include <linux/timer.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/imx-uart.h>
+#include <mach/mmc.h>
+#include <mach/imx-uart.h>
#include <linux/interrupt.h>
#include "generic.h"
&imx_uart2_device,
};
-#ifdef CONFIG_MMC_IMX
+#if defined(CONFIG_MMC_IMX) || defined(CONFIG_MMC_IMX_MODULE)
static int mx1ads_mmc_card_present(struct device *dev)
{
/* MMC/SD Card Detect is PB 20 on MX1ADS V1.0.7 */
#ifdef CONFIG_LEDS
imx_gpio_mode(GPIO_PORTA | GPIO_OUT | 2);
#endif
-#ifdef CONFIG_MMC_IMX
+#if defined(CONFIG_MMC_IMX) || defined(CONFIG_MMC_IMX_MODULE)
/* SD/MMC card detect */
imx_gpio_mode(GPIO_PORTB | GPIO_GIUS | GPIO_IN | 20);
imx_set_mmc_info(&mx1ads_mmc_info);
#include <linux/clockchips.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <linux/amba/bus.h>
#include <linux/amba/serial.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/hardware/arm_timer.h>
-#include <asm/arch/cm.h>
+#include <mach/cm.h>
#include <asm/system.h>
#include <asm/leds.h>
#include <asm/mach/time.h>
#include <linux/smp.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/hardware/icst525.h>
#include <asm/io.h>
#include <asm/hardware/icst525.h>
-#include <asm/arch/lm.h>
-#include <asm/arch/impd1.h>
+#include <mach/lm.h>
+#include <mach/impd1.h>
#include <asm/sizes.h>
#include "clock.h"
-/* linux/include/asm-arm/arch-integrator/debug-macro.S
+/* arch/arm/mach-integrator/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-integrator/dma.h
+ * arch/arm/mach-integrator/include/mach/dma.h
*
* Copyright (C) 1997,1998 Russell King
*
/*
- * include/asm-arm/arch-integrator/entry-macro.S
+ * arch/arm/mach-integrator/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Integrator platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
.macro disable_fiq
.endm
/*
- * linux/include/asm-arm/arch-integrator/hardware.h
+ * arch/arm/mach-integrator/include/mach/hardware.h
*
* This file contains the hardware definitions of the Integrator.
*
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* Where in virtual memory the IO devices (timers, system controllers
/*
- * linux/include/asm-arm/arch-integrator/io.h
+ * arch/arm/mach-integrator/include/mach/io.h
*
* Copyright (C) 1999 ARM Limited
*
/*
- * linux/include/asm-arm/arch-integrator/irqs.h
+ * arch/arm/mach-integrator/include/mach/irqs.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
/*
- * linux/include/asm-arm/arch-integrator/memory.h
+ * arch/arm/mach-integrator/include/mach/memory.h
*
* Copyright (C) 1999 ARM Limited
*
/*
- * linux/include/asm-arm/arch-integrator/system.h
+ * arch/arm/mach-integrator/include/mach/system.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/arch/cm.h>
+#include <mach/cm.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-integrator/timex.h
+ * arch/arm/mach-integrator/include/mach/timex.h
*
* Integrator architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-integrator/uncompress.h
+ * arch/arm/mach-integrator/include/mach/uncompress.h
*
* Copyright (C) 1999 ARM Limited
*
/*
- * linux/include/asm-arm/arch-integrator/vmalloc.h
+ * arch/arm/mach-integrator/include/mach/vmalloc.h
*
* Copyright (C) 2000 Russell King.
*
#include <linux/amba/bus.h>
#include <linux/amba/kmi.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/param.h> /* HZ */
#include <asm/mach-types.h>
-#include <asm/arch/lm.h>
+#include <mach/lm.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <linux/amba/kmi.h>
#include <linux/amba/clcd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/hardware/icst525.h>
-#include <asm/arch/cm.h>
-#include <asm/arch/lm.h>
+#include <mach/cm.h>
+#include <mach/lm.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <linux/smp.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <asm/mach-types.h>
-#include <asm/arch/cm.h>
+#include <mach/cm.h>
static int saved_leds;
#include <linux/device.h>
#include <linux/slab.h>
-#include <asm/arch/lm.h>
+#include <mach/lm.h>
#define to_lm_device(d) container_of(d, struct lm_device, dev)
#define to_lm_driver(d) container_of(d, struct lm_driver, drv)
#include <linux/spinlock.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#define _ADMA_H
#include <linux/types.h>
#include <linux/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iop_adma.h>
#define ADMA_ACCR(chan) (chan->mmr_base + 0x0)
/*
- * include/asm-arm/arch-iop13xx/debug-macro.S
+ * arch/arm/mach-iop13xx/include/mach/debug-macro.S
*
* Debugging macro include header
*
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
/*
* Physical DRAM offset.
#ifndef _IOP13XX_PCI_H_
#define _IOP13XX_PCI_H_
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/io.h>
struct pci_sys_data;
/*
- * linux/include/asm-arm/arch-iop13xx/system.h
+ * arch/arm/mach-iop13xx/include/mach/system.h
*
* Copyright (C) 2004 Intel Corp.
*
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/arch/iop13xx.h>
+#include <mach/iop13xx.h>
static inline void arch_idle(void)
{
cpu_do_idle();
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define CLOCK_TICK_RATE (100 * HZ)
#include <asm/types.h>
#include <linux/serial_reg.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define UART_BASE ((volatile u32 *)IOP13XX_UART1_PHYS)
#define TX_DONE (UART_LSR_TEMT | UART_LSR_THRE)
*/
#include <linux/kernel.h>
#include <linux/module.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
void * __iomem __iop13xx_io(unsigned long io_addr)
*/
#include <linux/pci.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/pci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/pci.h>
+#include <mach/pci.h>
#include <asm/mach/time.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
extern int init_atu; /* Flag to select which ATU(s) to initialize / disable */
*/
#include <linux/pci.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/pci.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/pci.h>
+#include <mach/pci.h>
#include <asm/mach/time.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
extern int init_atu;
#include <asm/uaccess.h>
#include <asm/mach/irq.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/msi.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/msi.h>
/* INTCTL0 CP6 R0 Page 4
*/
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/sizes.h>
#include <asm/signal.h>
#include <asm/mach/pci.h>
-#include <asm/arch/pci.h>
+#include <mach/pci.h>
#define IOP13XX_PCI_DEBUG 0
#define PRINTK(x...) ((void)(IOP13XX_PCI_DEBUG && printk(x)))
#include <linux/mtd/physmap.h>
#endif
#include <asm/mach/map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/hardware/iop_adma.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <asm/mach/time.h>
#include <asm/mach-types.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
static void __init em7210_timer_init(void)
{
#include <linux/mtd/physmap.h>
#include <linux/i2c.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach-types.h>
#include <asm/page.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* GLAN Tank timer tick configuration.
/*
- * include/asm-arm/arch-iop32x/debug-macro.S
+ * arch/arm/mach-iop32x/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * include/asm-arm/arch-iop33x/dma.h
+ * arch/arm/mach-iop32x/include/mach/dma.h
*
* Copyright (C) 2004 Intel Corp.
*
/*
- * include/asm-arm/arch-iop32x/entry-macro.S
+ * arch/arm/mach-iop32x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for IOP32x-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/iop32x.h>
+#include <mach/iop32x.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-iop32x/glantank.h
+ * arch/arm/mach-iop32x/include/mach/glantank.h
*
* IO-Data GLAN Tank board registers
*/
/*
- * include/asm-arm/arch-iop32x/hardware.h
+ * arch/arm/mach-iop32x/include/mach/hardware.h
*/
#ifndef __HARDWARE_H
/*
- * include/asm-arm/arch-iop32x/io.h
+ * arch/arm/mach-iop32x/include/mach/io.h
*
* Copyright (C) 2001 MontaVista Software, Inc.
*
#ifndef __IO_H
#define __IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
extern void __iomem *__iop3xx_ioremap(unsigned long cookie, size_t size,
unsigned int mtype);
/*
- * include/asm-arm/arch-iop32x/iop32x.h
+ * arch/arm/mach-iop32x/include/mach/iop32x.h
*
* Intel IOP32X Chip definitions
*
/*
- * include/asm-arm/arch-iop32x/iq31244.h
+ * arch/arm/mach-iop32x/include/mach/iq31244.h
*
* Intel IQ31244 evaluation board registers
*/
/*
- * include/asm-arm/arch-iop32x/iq80321.h
+ * arch/arm/mach-iop32x/include/mach/iq80321.h
*
* Intel IQ80321 evaluation board registers
*/
/*
- * include/asm-arm/arch-iop32x/irqs.h
+ * arch/arm/mach-iop32x/include/mach/irqs.h
*
* Author: Rory Bolt <rorybolt@pacbell.net>
* Copyright: (C) 2002 Rory Bolt
/*
- * include/asm-arm/arch-iop32x/memory.h
+ * arch/arm/mach-iop32x/include/mach/memory.h
*/
#ifndef __MEMORY_H
#define __MEMORY_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Physical DRAM offset.
/*
- * include/asm-arm/arch-iop32x/n2100.h
+ * arch/arm/mach-iop32x/include/mach/n2100.h
*
* Thecus N2100 board registers
*/
/*
- * include/asm-arm/arch-iop32x/system.h
+ * arch/arm/mach-iop32x/include/mach/system.h
*
* Copyright (C) 2001 MontaVista Software, Inc.
*
/*
- * include/asm-arm/arch-iop32x/timex.h
+ * arch/arm/mach-iop32x/include/mach/timex.h
*
* IOP32x architecture timex specifications
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define CLOCK_TICK_RATE (100 * HZ)
/*
- * include/asm-arm/arch-iop32x/uncompress.h
+ * arch/arm/mach-iop32x/include/mach/uncompress.h
*/
#include <asm/types.h>
#include <asm/mach-types.h>
#include <linux/serial_reg.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static volatile u8 *uart_base;
--- /dev/null
+/*
+ * arch/arm/mach-iop32x/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe000000
#include <linux/serial_8250.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/pgtable.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* Until March of 2007 iq31244 platforms and ep80219 platforms shared the
#include <linux/serial_8250.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/pgtable.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* IQ80321 timer tick configuration.
#include <linux/list.h>
#include <asm/mach/irq.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
static u32 iop32x_mask;
#include <linux/i2c.h>
#include <linux/platform_device.h>
#include <linux/reboot.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/pgtable.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* N2100 timer tick configuration.
/*
- * include/asm-arm/arch-iop33x/debug-macro.S
+ * arch/arm/mach-iop33x/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * include/asm-arm/arch-iop32x/dma.h
+ * arch/arm/mach-iop33x/include/mach/dma.h
*
* Copyright (C) 2004 Intel Corp.
*
/*
- * include/asm-arm/arch-iop33x/entry-macro.S
+ * arch/arm/mach-iop33x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for IOP33x-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/iop33x.h>
+#include <mach/iop33x.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-iop33x/hardware.h
+ * arch/arm/mach-iop33x/include/mach/hardware.h
*/
#ifndef __HARDWARE_H
/*
- * include/asm-arm/arch-iop33x/io.h
+ * arch/arm/mach-iop33x/include/mach/io.h
*
* Copyright (C) 2001 MontaVista Software, Inc.
*
#ifndef __IO_H
#define __IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
extern void __iomem *__iop3xx_ioremap(unsigned long cookie, size_t size,
unsigned int mtype);
/*
- * include/asm-arm/arch-iop33x/iop33x.h
+ * arch/arm/mach-iop33x/include/mach/iop33x.h
*
* Intel IOP33X Chip definitions
*
/*
- * include/asm-arm/arch-iop33x/iq80331.h
+ * arch/arm/mach-iop33x/include/mach/iq80331.h
*
* Intel IQ80331 evaluation board registers
*/
/*
- * include/asm-arm/arch-iop33x/iq80332.h
+ * arch/arm/mach-iop33x/include/mach/iq80332.h
*
* Intel IQ80332 evaluation board registers
*/
/*
- * include/asm-arm/arch-iop33x/irqs.h
+ * arch/arm/mach-iop33x/include/mach/irqs.h
*
* Author: Dave Jiang (dave.jiang@intel.com)
* Copyright: (C) 2003 Intel Corp.
/*
- * include/asm-arm/arch-iop33x/memory.h
+ * arch/arm/mach-iop33x/include/mach/memory.h
*/
#ifndef __MEMORY_H
#define __MEMORY_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Physical DRAM offset.
/*
- * include/asm-arm/arch-iop33x/system.h
+ * arch/arm/mach-iop33x/include/mach/system.h
*
* Copyright (C) 2001 MontaVista Software, Inc.
*
/*
- * include/asm-arm/arch-iop33x/timex.h
+ * arch/arm/mach-iop33x/include/mach/timex.h
*
* IOP3xx architecture timex specifications
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define CLOCK_TICK_RATE (100 * HZ)
/*
- * include/asm-arm/arch-iop33x/uncompress.h
+ * arch/arm/mach-iop33x/include/mach/uncompress.h
*/
#include <asm/types.h>
#include <asm/mach-types.h>
#include <linux/serial_reg.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static volatile u32 *uart_base;
--- /dev/null
+/*
+ * arch/arm/mach-iop33x/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe000000
#include <linux/serial_8250.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/pgtable.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* IQ80331 timer tick configuration.
#include <linux/serial_8250.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/page.h>
#include <asm/pgtable.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
/*
* IQ80332 timer tick configuration.
#include <linux/list.h>
#include <asm/mach/irq.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
static u32 iop33x_mask0;
#include <asm/setup.h>
#include <asm/system.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iop3xx.h>
-#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#define IOP33X_UART_XTAL 33334000
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/tlbflush.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
static DEFINE_SPINLOCK(ixp2000_slowport_lock);
static unsigned long ixp2000_slowport_irq_flags;
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
-/* linux/include/asm-arm/arch-ixp2000/debug-macro.S
+/* arch/arm/mach-ixp2000/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-ixp2000/dma.h
+ * arch/arm/mach-ixp2000/include/mach/dma.h
*
* Copyright (C) 2002 Intel Corp.
*
/*
- * include/asm-arm/arch-ixp2000/enp2611.h
+ * arch/arm/mach-ixp2000/include/mach/enp2611.h
*
* Register and other defines for Radisys ENP-2611
*
/*
- * include/asm-arm/arch-ixp2000/entry-macro.S
+ * arch/arm/mach-ixp2000/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for IXP2000-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-ixp2000/gpio.h
+ * arch/arm/mach-ixp2000/include/mach/gpio.h
*
* Copyright (C) 2002 Intel Corporation.
*
/*
- * linux/include/asm-arm/arch-ixp2000/hardware.h
+ * arch/arm/mach-ixp2000/include/mach/hardware.h
*
* Hardware definitions for IXP2400/2800 based systems
*
/*
- * linux/include/asm-arm/arch-ixp2000/io.h
+ * arch/arm/mach-ixp2000/include/mach/io.h
*
* Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
* Maintainer: Deepak Saxena <dsaxena@plexity.net>
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
#define __mem_pci(a) (a)
/*
- * linux/include/asm-arm/arch-ixp2000/irqs.h
+ * arch/arm/mach-ixp2000/include/mach/irqs.h
*
* Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
* Maintainer: Deepak Saxena <dsaxena@plexity.net>
/*
- * include/asm-arm/arch-ixp2000/ixdp2x00.h
+ * arch/arm/mach-ixp2000/include/mach/ixdp2x00.h
*
* Register and other defines for IXDP2[48]00 platforms
*
/*
- * include/asm-arm/arch-ixp2000/ixdp2x01.h
+ * arch/arm/mach-ixp2000/include/mach/ixdp2x01.h
*
* Platform definitions for IXDP2X01 && IXDP2801 systems
*
/*
- * include/asm-arm/arch-ixp2000/ixp2000-regs.h
+ * arch/arm/mach-ixp2000/include/mach/ixp2000-regs.h
*
* Chipset register definitions for IXP2400/2800 based systems.
*
/*
- * linux/include/asm-arm/arch-ixp2000/memory.h
+ * arch/arm/mach-ixp2000/include/mach/memory.h
*
* Copyright (c) 2002 Intel Corp.
* Copyright (c) 2003-2004 MontaVista Software, Inc.
* bus_to_virt: Used to convert an address for DMA operations
* to an address that the kernel can use.
*/
-#include <asm/arch/ixp2000-regs.h>
+#include <mach/ixp2000-regs.h>
#define __virt_to_bus(v) \
(((__virt_to_phys(v) - 0x0) + (*IXP2000_PCI_SDRAM_BAR & 0xfffffff0)))
/*
- * include/asm-arm/arch-ixp2000/platform.h
+ * arch/arm/mach-ixp2000/include/mach/platform.h
*
* Various bits of code used by platform-level code.
*
/*
- * linux/include/asm-arm/arch-ixp2000/system.h
+ * arch/arm/mach-ixp2000/include/mach/system.h
*
* Copyright (C) 2002 Intel Corp.
* Copyricht (C) 2003-2005 MontaVista Software, Inc.
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
static inline void arch_idle(void)
/*
- * linux/include/asm-arm/arch-ixp2000/timex.h
+ * arch/arm/mach-ixp2000/include/mach/timex.h
*
* IXP2000 architecture timex specifications
*/
/*
- * linux/include/asm-arm/arch-ixp2000/uncompress.h
+ * arch/arm/mach-ixp2000/include/mach/uncompress.h
*
*
* Original Author: Naeem Afzal <naeem.m.afzal@intel.com>
/*
- * linux/include/asm-arm/arch-ixp2000/vmalloc.h
+ * arch/arm/mach-ixp2000/include/mach/vmalloc.h
*
* Author: Naeem Afzal <naeem.m.afzal@intel.com>
*
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
#include <asm/mach/flash.h>
#include <asm/mach/arch.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
/*************************************************************************
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/pci.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/tlbflush.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/system.h>
/*
- * include/asm-arm/arch-ixp23xx/debug-macro.S
+ * arch/arm/mach-ixp23xx/include/mach/debug-macro.S
*
* Debugging macro include header
*
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/arch/ixp23xx.h>
+#include <mach/ixp23xx.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
--- /dev/null
+/*
+ * arch/arm/mach-ixp23xx/include/mach/dma.h
+ */
/*
- * include/asm-arm/arch-ixp23xx/entry-macro.S
+ * arch/arm/mach-ixp23xx/include/mach/entry-macro.S
*/
.macro disable_fiq
/*
- * include/asm-arm/arch-ixp23xx/hardware.h
+ * arch/arm/mach-ixp23xx/include/mach/hardware.h
*
* Copyright (C) 2002-2004 Intel Corporation.
* Copyricht (C) 2005 MontaVista Software, Inc.
/*
- * include/asm-arm/arch-ixp23xx/io.h
+ * arch/arm/mach-ixp23xx/include/mach/io.h
*
* Original Author: Naeem M Afzal <naeem.m.afzal@intel.com>
* Maintainer: Deepak Saxena <dsaxena@plexity.net>
/*
- * include/asm-arm/arch-ixp23xx/irqs.h
+ * arch/arm/mach-ixp23xx/include/mach/irqs.h
*
* IRQ definitions for IXP23XX based systems
*
/*
- * include/asm-arm/arch-ixp23xx/ixdp2351.h
+ * arch/arm/mach-ixp23xx/include/mach/ixdp2351.h
*
* Register and other defines for IXDP2351
*
/*
- * include/asm-arm/arch-ixp23xx/ixp23xx.h
+ * arch/arm/mach-ixp23xx/include/mach/ixp23xx.h
*
* Register definitions for IXP23XX
*
/*
- * include/asm-arm/arch-ixp23xx/memory.h
+ * arch/arm/mach-ixp23xx/include/mach/memory.h
*
* Copyright (c) 2003-2004 Intel Corp.
*
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Physical DRAM offset.
* to an address that the kernel can use.
*/
#ifndef __ASSEMBLY__
-#include <asm/mach-types.h>
#define __virt_to_bus(v) \
({ unsigned int ret; \
/*
- * include/asm-arm/arch-ixp23xx/platform.h
+ * arch/arm/mach-ixp23xx/include/mach/platform.h
*
* Various bits of code used by platform-level code.
*
/*
- * include/asm-arm/arch-ixp23xx/system.h
+ * arch/arm/mach-ixp23xx/include/mach/system.h
*
* Copyright (C) 2003 Intel Corporation.
*
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
static inline void arch_idle(void)
--- /dev/null
+/*
+ * arch/arm/mach-ixp23xx/include/mach/time.h
+ */
/*
- * include/asm-arm/arch-ixp23xx/timex.h
+ * arch/arm/mach-ixp23xx/include/mach/timex.h
*
* XScale architecture timex specifications
*/
/*
- * include/asm-arm/arch-ixp23xx/uncompress.h
+ * arch/arm/mach-ixp23xx/include/mach/uncompress.h
*
* Copyright (C) 2002-2004 Intel Corporation.
*
#ifndef __ASM_ARCH_UNCOMPRESS_H
#define __ASM_ARCH_UNCOMPRESS_H
-#include <asm/arch/ixp23xx.h>
+#include <mach/ixp23xx.h>
#include <linux/serial_reg.h>
#define UART_BASE ((volatile u32 *)IXP23XX_UART1_PHYS)
/*
- * include/asm-arm/arch-ixp23xx/vmalloc.h
+ * arch/arm/mach-ixp23xx/include/mach/vmalloc.h
*
* Copyright (c) 2005 MontaVista Software, Inc.
*
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/system.h>
#include <asm/tlbflush.h>
#include <asm/sizes.h>
#include <asm/system.h>
#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
extern int (*external_fault) (unsigned long, struct pt_regs *);
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/mach/pci.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
void __init avila_pci_preinit(void)
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/sizes.h>
#include <asm/system.h>
#include <asm/mach/pci.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
#include <linux/clocksource.h>
#include <linux/clockchips.h>
-#include <asm/arch/udc.h>
-#include <asm/hardware.h>
+#include <mach/udc.h>
+#include <mach/hardware.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/pgtable.h>
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/pci.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/pci.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
-#include <asm/arch/gtwx5715.h>
+#include <mach/hardware.h>
+#include <mach/gtwx5715.h>
#include <asm/mach/pci.h>
/*
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/arch/gtwx5715.h>
+#include <mach/gtwx5715.h>
/*
* Xscale UART registers are 32 bits wide with only the least
/*
- * include/asm-arm/arch-ixp4xx/avila.h
+ * arch/arm/mach-ixp4xx/include/mach/avila.h
*
* Gateworks Avila platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define AVILA_SDA_PIN 7
/*
- * include/asm-arm/arch-ixp4xx/coyote.h
+ * arch/arm/mach-ixp4xx/include/mach/coyote.h
*
* ADI Engineering platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
/* PCI controller GPIO to IRQ pin mappings */
/*
- * include/asm-arm/arch-ixp4xx/cpu.h
+ * arch/arm/mach-ixp4xx/include/mach/cpu.h
*
* IXP4XX cpu type detection
*
-/* linux/include/asm-arm/arch-ixp4xx/debug-macro.S
+/* arch/arm/mach-ixp4xx/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * include/asm-arm/arch-ixp4xx/dma.h
+ * arch/arm/mach-ixp4xx/include/mach/dma.h
*
* Copyright (C) 2001-2004 MontaVista Software, Inc.
*
#include <linux/device.h>
#include <asm/page.h>
#include <asm/sizes.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define MAX_DMA_ADDRESS (PAGE_OFFSET + SZ_64M)
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define DSMG600_SDA_PIN 5
/*
- * include/asm-arm/arch-ixp4xx/entry-macro.S
+ * arch/arm/mach-ixp4xx/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for IXP4xx-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-ixp4xx/fsg.h
+ * arch/arm/mach-ixp4xx/include/mach/fsg.h
*
* Freecom FSG-3 platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define FSG_SDA_PIN 12
/*
- * linux/include/asm-arm/arch-ixp4xx/gpio.h
+ * arch/arm/mach-ixp4xx/include/mach/gpio.h
*
* IXP4XX GPIO wrappers for arch-neutral GPIO calls
*
#ifndef __ASM_ARCH_IXP4XX_GPIO_H
#define __ASM_ARCH_IXP4XX_GPIO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static inline int gpio_request(unsigned gpio, const char *label)
{
/*
- * include/asm-arm/arch-ixp4xx/gtwx5715.h
+ * arch/arm/mach-ixp4xx/include/mach/gtwx5715.h
*
* Gemtek GTWX5715 Gateway (Linksys WRV54G)
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#include "irqs.h"
/*
- * include/asm-arm/arch-ixp4xx/hardware.h
+ * arch/arm/mach-ixp4xx/include/mach/hardware.h
*
* Copyright (C) 2002 Intel Corporation.
* Copyright (C) 2003-2004 MontaVista Software, Inc.
#include "ixp4xx-regs.h"
#ifndef __ASSEMBLER__
-#include <asm/arch/cpu.h>
+#include <mach/cpu.h>
#endif
/* Platform helper functions and definitions */
/*
- * linux/include/asm-arm/arch-ixp4xx/io.h
+ * arch/arm/mach-ixp4xx/include/mach/io.h
*
* Author: Deepak Saxena <dsaxena@plexity.net>
*
#include <linux/bitops.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffff0000
/*
- * include/asm-arm/arch-ixp4xx/irqs.h
+ * arch/arm/mach-ixp4xx/include/mach/irqs.h
*
* IRQ definitions for IXP4XX based systems
*
/*
- * include/asm-arm/arch-ixp4xx/ixdp425.h
+ * arch/arm/mach-ixp4xx/include/mach/ixdp425.h
*
* IXDP425 platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define IXDP425_SDA_PIN 7
/*
- * include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
+ * arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
*
* Register definitions for IXP4xx chipset. This file contains
* register location and bit definitions only. Platform specific
/*
- * linux/include/asm-arm/arch-ixp4xx/memory.h
+ * arch/arm/mach-ixp4xx/include/mach/memory.h
*
* Copyright (c) 2001-2004 MontaVista Software, Inc.
*/
/*
- * include/asm-arm/arch-ixp4xx/nas100d.h
+ * arch/arm/mach-ixp4xx/include/mach/nas100d.h
*
* NAS100D platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define NAS100D_SDA_PIN 5
/*
- * include/asm-arm/arch-ixp4xx/nslu2.h
+ * arch/arm/mach-ixp4xx/include/mach/nslu2.h
*
* NSLU2 platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define NSLU2_SDA_PIN 7
/*
- * include/asm-arm/arch-ixp4xx/platform.h
+ * arch/arm/mach-ixp4xx/include/mach/platform.h
*
* Constants and functions that are useful to IXP4xx platform-specific code
* and device drivers.
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#ifndef __ASSEMBLY__
/*
- * include/asm-arm/arch-ixp4xx/prpmc1100.h
+ * arch/arm/mach-ixp4xx/include/mach/prpmc1100.h
*
* Motorolla PrPMC1100 platform specific definitions
*
*/
#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <asm/hardware.h>"
+#error "Do not include this directly, instead #include <mach/hardware.h>"
#endif
#define PRPMC1100_FLASH_BASE IXP4XX_EXP_BUS_CS0_BASE_PHYS
/*
- * include/asm-arm/arch-ixp4xx/system.h
+ * arch/arm/mach-ixp4xx/include/mach/system.h
*
* Copyright (C) 2002 Intel Corporation.
*
*
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-ixp4xx/timex.h
+ * arch/arm/mach-ixp4xx/include/mach/timex.h
*
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* We use IXP425 General purpose timer for our timer needs, it runs at
/*
- * linux/include/asm-arm/arch-ixp4xx/udc.h
+ * arch/arm/mach-ixp4xx/include/mach/udc.h
*
*/
#include <asm/mach/udc_pxa2xx.h>
/*
- * include/asm-arm/arch-ixp4xx/uncompress.h
+ * arch/arm/mach-ixp4xx/include/mach/uncompress.h
*
* Copyright (C) 2002 Intel Corporation.
* Copyright (C) 2003-2004 MontaVista Software, Inc.
/*
- * linux/include/asm-arm/arch-ixp4xx/vmalloc.h
+ * arch/arm/mach-ixp4xx/include/mach/vmalloc.h
*/
#define VMALLOC_END (0xFF000000)
#include <asm/mach/pci.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
void __init ixdp425_pci_preinit(void)
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/pci.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
-#include <asm/arch/npe.h>
+#include <mach/npe.h>
#define DEBUG_MSG 0
#define DEBUG_FW 0
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
-#include <asm/arch/qmgr.h>
+#include <mach/qmgr.h>
#define DEBUG 0
#include <linux/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/pci.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/init.h>
#include <linux/mbus.h>
#include <linux/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "common.h"
/*
#include <asm/timex.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
#include <asm/plat-orion/cache-feroceon-l2.h>
#include <asm/plat-orion/ehci-orion.h>
#include <asm/plat-orion/orion_nand.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
#include "common.h"
static struct mv643xx_eth_platform_data db88f6281_ge00_data = {
/*
- * include/asm-arm/arch-kirkwood/debug-macro.S
+ * arch/arm/mach-kirkwood/include/mach/debug-macro.S
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-kirkwood/entry-macro.S
+ * arch/arm/mach-kirkwood/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Marvell Kirkwood platforms
*
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-kirkwood/hardware.h
+ * arch/arm/mach-kirkwood/include/mach/hardware.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * include/asm-arm/arch-kirkwood/io.h
+ * arch/arm/mach-kirkwood/include/mach/io.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-kirkwood/irqs.h
+ * arch/arm/mach-kirkwood/include/mach/irqs.h
*
* IRQ definitions for Marvell Kirkwood SoCs
*
/*
- * include/asm-arm/arch-kirkwood/kirkwood.h
+ * arch/arm/mach-kirkwood/include/mach/kirkwood.h
*
* Generic definitions for Marvell Kirkwood SoC flavors:
* 88F6180, 88F6192 and 88F6281.
/*
- * include/asm-arm/arch-loki/memory.h
+ * arch/arm/mach-kirkwood/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
/*
- * include/asm-arm/arch-mv78xx0/system.h
+ * arch/arm/mach-kirkwood/include/mach/system.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/arch/hardware.h>
-#include <asm/arch/mv78xx0.h>
+#include <mach/hardware.h>
+#include <mach/kirkwood.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-kirkwood/timex.h
+ * arch/arm/mach-kirkwood/include/mach/timex.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-kirkwood/uncompress.h
+ * arch/arm/mach-kirkwood/include/mach/uncompress.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
*/
#include <linux/serial_reg.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE)
--- /dev/null
+/*
+ * arch/arm/mach-kirkwood/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe800000
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
#include "common.h"
#define RD88F6192_GPIO_USB_VBUS 10
#include <linux/timer.h>
#include <linux/ata_platform.h>
#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/kirkwood.h>
#include <asm/plat-orion/orion_nand.h>
#include "common.h"
static struct mv643xx_eth_platform_data rd88f6281_ge00_data = {
.phy_addr = -1,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
};
static struct mv_sata_platform_data rd88f6281_sata_data = {
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/devices.h>
+#include <mach/devices.h>
#include "generic.h"
#include <linux/module.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/regs-sys.h>
-#include <asm/arch/regs-misc.h>
+#include <mach/regs-sys.h>
+#include <mach/regs-misc.h>
static struct __initdata map_desc ks8695_io_desc[] = {
#include <linux/platform_device.h>
-#include <asm/arch/regs-wan.h>
-#include <asm/arch/regs-lan.h>
-#include <asm/arch/regs-hpna.h>
+#include <mach/regs-wan.h>
+#include <mach/regs-lan.h>
+#include <mach/regs-hpna.h>
/* --------------------------------------------------------------------
#include <linux/module.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/gpio.h>
+#include <mach/regs-gpio.h>
+#include <mach/gpio.h>
/*
* Configure a GPIO line for either GPIO function, or its internal
/*
- * include/asm-arm/arch-ks8695/debug-macro.S
+ * arch/arm/mach-ks8695/include/mach/debug-macro.S
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
-#include <asm/arch/regs-uart.h>
+#include <mach/hardware.h>
+#include <mach/regs-uart.h>
.macro addruart, rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-ks8695/devices.h
+ * arch/arm/mach-ks8695/include/mach/devices.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/dma.h
+ * arch/arm/mach-ks8695/include/mach/dma.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
/*
- * include/asm-arm/arch-ks8695/entry-macro.S
+ * arch/arm/mach-ks8695/include/mach/entry-macro.S
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/hardware.h>
+#include <mach/regs-irq.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-ks8695/gpio.h
+ * arch/arm/mach-ks8695/include/mach/gpio.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/hardware.h
+ * arch/arm/mach-ks8695/include/mach/hardware.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * include/asm-arm/arch-ks8695/io.h
+ * arch/arm/mach-ks8695/include/mach/io.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * linux/include/asm-arm/arch-ks8695/irqs.h
+ * arch/arm/mach-ks8695/include/mach/irqs.h
*
* Copyright (C) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
/*
- * include/asm-arm/arch-ks8695/memory.h
+ * arch/arm/mach-ks8695/include/mach/memory.h
*
* Copyright (C) 2006 Andrew Victor
*
#ifndef __ASM_ARCH_MEMORY_H
#define __ASM_ARCH_MEMORY_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Physical SRAM offset.
/*
- * include/asm-arm/arch-ks8695/regs-gpio.h
+ * arch/arm/mach-ks8695/include/mach/regs-gpio.h
*
* Copyright (C) 2007 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-wan.h
+ * arch/arm/mach-ks8695/include/mach/regs-wan.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-irq.h
+ * arch/arm/mach-ks8695/include/mach/regs-irq.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * include/asm-arm/arch-ks8695/regs-lan.h
+ * arch/arm/mach-ks8695/include/mach/regs-lan.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-mem.h
+ * arch/arm/mach-ks8695/include/mach/regs-mem.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-misc.h
+ * arch/arm/mach-ks8695/include/mach/regs-misc.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-pci.h
+ * arch/arm/mach-ks8695/include/mach/regs-pci.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * include/asm-arm/arch-ks8695/regs-switch.h
+ * arch/arm/mach-ks8695/include/mach/regs-switch.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-ks8695/regs-sys.h
+ * arch/arm/mach-ks8695/include/mach/regs-sys.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * include/asm-arm/arch-ks8695/regs-timer.h
+ * arch/arm/mach-ks8695/include/mach/regs-timer.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * linux/include/asm-arm/arch-ks8695/regs-uart.h
+ * arch/arm/mach-ks8695/include/mach/regs-uart.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
/*
- * include/asm-arm/arch-ks8695/regs-wan.h
+ * arch/arm/mach-ks8695/include/mach/regs-wan.h
*
* Copyright (C) 2006 Andrew Victor
*
/*
- * include/asm-arm/arch-s3c2410/system.h
+ * arch/arm/mach-s3c2410/include/mach/system.h
*
* Copyright (C) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
#define __ASM_ARCH_SYSTEM_H
#include <asm/io.h>
-#include <asm/arch/regs-timer.h>
+#include <mach/regs-timer.h>
static void arch_idle(void)
{
/*
- * include/asm-arm/arch-ks8695/timex.h
+ * arch/arm/mach-ks8695/include/mach/timex.h
*
* Copyright (C) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
/*
- * include/asm-arm/arch-ks8695/uncompress.h
+ * arch/arm/mach-ks8695/include/mach/uncompress.h
*
* Copyright (C) 2006 Ben Dooks <ben@simtec.co.uk>
* Copyright (C) 2006 Simtec Electronics
#define __ASM_ARCH_UNCOMPRESS_H
#include <asm/io.h>
-#include <asm/arch/regs-uart.h>
+#include <mach/regs-uart.h>
static void putc(char c)
{
/*
- * include/asm-arm/arch-ks8695/vmalloc.h
+ * arch/arm/mach-ks8695/include/mach/vmalloc.h
*
* Copyright (C) 2006 Ben Dooks
* Copyright (C) 2006 Simtec Electronics <linux@simtec.co.uk>
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
static void ks8695_irq_mask(unsigned int irqno)
{
#include <linux/module.h>
#include <linux/init.h>
-#include <asm/mach-types.h>
#include <asm/leds.h>
-#include <asm/arch/devices.h>
-#include <asm/arch/gpio.h>
+#include <mach/devices.h>
+#include <mach/gpio.h>
static inline void ks8695_led_on(unsigned int led)
#include <asm/io.h>
#include <asm/signal.h>
#include <asm/mach/pci.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/devices.h>
-#include <asm/arch/regs-pci.h>
+#include <mach/devices.h>
+#include <mach/regs-pci.h>
static int pci_dbg;
#include <asm/io.h>
#include <asm/mach/time.h>
-#include <asm/arch/regs-timer.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-timer.h>
+#include <mach/regs-irq.h>
#include "generic.h"
#include <asm/types.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include <asm/mach/arch.h>
/*
- * linux/include/asm-arm/arch-l7200/aux_reg.h
+ * arch/arm/mach-l7200/include/mach/aux_reg.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
#ifndef _ASM_ARCH_AUXREG_H
#define _ASM_ARCH_AUXREG_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define l7200aux_reg *((volatile unsigned int *) (AUX_BASE))
-/* linux/include/asm-arm/arch-l7200/debug-macro.S
+/* arch/arm/mach-l7200/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-l7200/dma.h
+ * arch/arm/mach-l7200/include/mach/dma.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
/*
- * include/asm-arm/arch-l7200/entry-macro.S
+ * arch/arm/mach-l7200/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for L7200-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.equ irq_base_addr, IO_BASE_2
/*
- * linux/include/asm-arm/arch-l7200/gp_timers.h
+ * arch/arm/mach-l7200/include/mach/gp_timers.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
#ifndef _ASM_ARCH_GPTIMERS_H
#define _ASM_ARCH_GPTIMERS_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Layout of L7200 general purpose timer registers
/****************************************************************************/
/*
- * linux/include/asm-arm/arch-l7200/gpio.h
+ * arch/arm/mach-l7200/include/mach/gpio.h
*
* Registers and helper functions for the L7200 Link-Up Systems
* GPIO.
/*
- * linux/include/asm-arm/arch-l7200/hardware.h
+ * arch/arm/mach-l7200/include/mach/hardware.h
*
* Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
* Steve Hill (sjhill@cotw.com)
/*
- * linux/include/asm-arm/arch-l7200/io.h
+ * arch/arm/mach-l7200/include/mach/io.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
* Changelog:
- * 03-21-2000 SJH Created from linux/include/asm-arm/arch-nexuspci/io.h
+ * 03-21-2000 SJH Created from arch/arm/mach-nexuspci/include/mach/io.h
* 08-31-2000 SJH Added in IO functions necessary for new drivers
*/
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * include/asm-arm/arch-l7200/irqs.h
+ * arch/arm/mach-l7200/include/mach/irqs.h
*
* Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
* Steve Hill (sjhill@cotw.com)
/*
- * linux/include/asm-arm/arch-l7200/memory.h
+ * arch/arm/mach-l7200/include/mach/memory.h
*
* Copyright (c) 2000 Steve Hill (sjhill@cotw.com)
* Copyright (c) 2000 Rob Scott (rscott@mtrob.fdns.net)
/****************************************************************************/
/*
- * linux/include/asm-arm/arch-l7200/pmpcon.h
+ * arch/arm/mach-l7200/include/mach/pmpcon.h
*
* Registers and helper functions for the L7200 Link-Up Systems
* DC/DC converter register.
/****************************************************************************/
/*
- * linux/include/asm-arm/arch-l7200/pmu.h
+ * arch/arm/mach-l7200/include/mach/pmu.h
*
* Registers and helper functions for the L7200 Link-Up Systems
* Power Management Unit (PMU).
/*
- * linux/include/asm-arm/arch-l7200/serial.h
+ * arch/arm/mach-l7200/include/mach/serial.h
*
* Copyright (c) 2000 Rob Scott (rscott@mtrob.fdns.net)
* Steve Hill (sjhill@cotw.com)
/*
- * linux/include/asm-arm/arch-l7200/serial_l7200.h
+ * arch/arm/mach-l7200/include/mach/serial_l7200.h
*
* Copyright (c) 2000 Steven Hill (sjhill@cotw.com)
*
#ifndef __ASM_ARCH_SERIAL_L7200_H
#define __ASM_ARCH_SERIAL_L7200_H
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
/*
* This assumes you have a 3.6864 MHz clock for your UART.
/****************************************************************************/
/*
- * linux/include/asm-arm/arch-l7200/sib.h
+ * arch/arm/mach-l7200/include/mach/sib.h
*
* Registers and helper functions for the Serial Interface Bus.
*
/****************************************************************************/
/*
- * linux/include/asm-arm/arch-l7200/sys-clock.h
+ * arch/arm/mach-l7200/include/mach/sys-clock.h
*
* Registers and helper functions for the L7200 Link-Up Systems
* System clocks.
/*
- * linux/include/asm-arm/arch-l7200/system.h
+ * arch/arm/mach-l7200/include/mach/system.h
*
* Copyright (c) 2000 Steve Hill (sjhill@cotw.com)
*
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-l7200/time.h
+ * arch/arm/mach-l7200/include/mach/time.h
*
* Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
* Steve Hill (sjhill@cotw.com)
#ifndef _ASM_ARCH_TIME_H
#define _ASM_ARCH_TIME_H
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
/*
* RTC base register address
/*
- * linux/include/asm-arm/arch-l7200/timex.h
+ * arch/arm/mach-l7200/include/mach/timex.h
*
* Copyright (C) 2000 Rob Scott (rscott@mtrob.fdns.net)
* Steve Hill (sjhill@cotw.com)
/*
- * linux/include/asm-arm/arch-l7200/uncompress.h
+ * arch/arm/mach-l7200/include/mach/uncompress.h
*
* Copyright (C) 2000 Steve Hill (sjhill@cotw.com)
*
* 07-26-2000 SJH Removed hard coded baud rate
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_UART IO_START + 0x00044000
/*
- * linux/include/asm-arm/arch-l7200/vmalloc.h
+ * arch/arm/mach-l7200/include/mach/vmalloc.h
*/
#define VMALLOC_END (PAGE_OFFSET + 0x10000000)
#include <linux/device.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
//#include <linux/module.h>
//#include <linux/time.h>
-//#include <asm/hardware.h>
//#include <asm/mach/time.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
*/
#include <linux/cpufreq.h>
-#include <asm/hardware.h>
-#include <asm/arch/clocks.h>
+#include <mach/hardware.h>
+#include <mach/clocks.h>
#include <linux/err.h>
struct module;
-/* include/asm-arm/arch-lh7a40x/clocks.h
+/* arch/arm/mach-lh7a40x/include/mach/clocks.h
*
* Copyright (C) 2004 Marc Singer
*
-/* include/asm-arm/arch-lh7a40x/constants.h
+/* arch/arm/mach-lh7a40x/include/mach/constants.h
*
* Copyright (C) 2004 Coastal Environmental Systems
* Copyright (C) 2004 Logic Product Development
-/* linux/include/asm-arm/arch-lh7a40x/debug-macro.S
+/* arch/arm/mach-lh7a40x/include/mach/debug-macro.S
*
* Debugging macro include header
*
-/* include/asm-arm/arch-lh7a40x/dma.h
+/* arch/arm/mach-lh7a40x/include/mach/dma.h
*
* Copyright (C) 2005 Marc Singer
*
/*
- * include/asm-arm/arch-lh7a40x/entry-macro.S
+ * arch/arm/mach-lh7a40x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for LH7A40x platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
/* In order to allow there to be support for both of the processor
classes at the same time, we make a hack here that isn't very
-/* include/asm-arm/arch-lh7a40x/hardware.h
+/* arch/arm/mach-lh7a40x/include/mach/hardware.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
- * [ Substantially cribbed from include/asm-arm/arch-pxa/hardware.h ]
+ * [ Substantially cribbed from arch/arm/mach-pxa/include/mach/hardware.h ]
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
-/* include/asm-arm/arch-lh7a40x/io.h
+/* arch/arm/mach-lh7a40x/include/mach/io.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
#ifndef __ASM_ARCH_IO_H
#define __ASM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
-/* include/asm-arm/arch-lh7a40x/irqs.h
+/* arch/arm/mach-lh7a40x/include/mach/irqs.h
*
* Copyright (C) 2004 Coastal Environmental Systems
* Copyright (C) 2004 Logic Product Development
-/* include/asm-arm/arch-lh7a40x/memory.h
+/* arch/arm/mach-lh7a40x/include/mach/memory.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
-/* include/asm-arm/arch-lh7a40x/registers.h
+/* arch/arm/mach-lh7a40x/include/mach/registers.h
*
* Copyright (C) 2004 Coastal Environmental Systems
* Copyright (C) 2004 Logic Product Development
*
*/
-#include <asm/arch/constants.h>
+#include <mach/constants.h>
#ifndef __ASM_ARCH_REGISTERS_H
#define __ASM_ARCH_REGISTERS_H
-/* include/asm-arm/arch-lh7a40x/system.h
+/* arch/arm/mach-lh7a40x/include/mach/system.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
-/* include/asm-arm/arch-lh7a40x/timex.h
+/* arch/arm/mach-lh7a40x/include/mach/timex.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
*
*/
-#include <asm/arch/constants.h>
+#include <mach/constants.h>
#define CLOCK_TICK_RATE (PLL_CLOCK/6/16)
-/* include/asm-arm/arch-lh7a40x/uncompress.h
+/* arch/arm/mach-lh7a40x/include/mach/uncompress.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
*
*/
-#include <asm/arch/registers.h>
+#include <mach/registers.h>
#ifndef UART_R_DATA
# define UART_R_DATA (0x00)
-/* include/asm-arm/arch-lh7a40x/vmalloc.h
+/* arch/arm/mach-lh7a40x/include/mach/vmalloc.h
*
* Copyright (C) 2004 Coastal Environmental Systems
*
#include <linux/module.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include "common.h"
#include <linux/module.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include "common.h"
#include <linux/module.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include "common.h"
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/ssp.h>
+#include <mach/ssp.h>
//#define TALK
#include <linux/irq.h>
#include <linux/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include "common.h"
#include <asm/timex.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/arch/loki.h>
+#include <mach/loki.h>
#include <asm/plat-orion/orion_nand.h>
#include <asm/plat-orion/time.h>
#include "common.h"
/*
- * include/asm-arm/arch-loki/debug-macro.S
+ * arch/arm/mach-loki/include/mach/debug-macro.S
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/arch/loki.h>
+#include <mach/loki.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-loki/entry-macro.S
+ * arch/arm/mach-loki/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Marvell Loki (88RC8480) platforms
*
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/loki.h>
+#include <mach/loki.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-loki/hardware.h
+ * arch/arm/mach-loki/include/mach/hardware.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * include/asm-arm/arch-loki/io.h
+ * arch/arm/mach-loki/include/mach/io.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-loki/irqs.h
+ * arch/arm/mach-loki/include/mach/irqs.h
*
* IRQ definitions for Marvell Loki (88RC8480) SoCs
*
/*
- * include/asm-arm/arch-loki/loki.h
+ * arch/arm/mach-loki/include/mach/loki.h
*
* Generic definitions for Marvell Loki (88RC8480) SoC flavors
*
/*
- * include/asm-arm/arch-mv78xx0/memory.h
+ * arch/arm/mach-loki/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
/*
- * include/asm-arm/arch-loki/system.h
+ * arch/arm/mach-loki/include/mach/system.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/arch/hardware.h>
-#include <asm/arch/loki.h>
+#include <mach/hardware.h>
+#include <mach/loki.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-loki/timex.h
+ * arch/arm/mach-loki/include/mach/timex.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-loki/uncompress.h
+ * arch/arm/mach-loki/include/mach/uncompress.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
*/
#include <linux/serial_reg.h>
-#include <asm/arch/loki.h>
+#include <mach/loki.h>
#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE)
--- /dev/null
+/*
+ * arch/arm/mach-loki/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe800000
#include <linux/mv643xx_eth.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/loki.h>
+#include <mach/loki.h>
#include "common.h"
#define LB88RC8480_FLASH_BOOT_CS_BASE 0xf8000000
#include <linux/platform_device.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/board.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/board.h>
+#include <mach/msm_iomap.h>
#include <asm/io.h>
#include <asm/delay.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
struct flash_platform_data msm_nand_data = {
.parts = 0,
#include <asm/io.h>
#include <linux/interrupt.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#define MSM_DMOV_CHANNEL_COUNT 16
-/* linux/include/asm-arm/arch-msm/idle.S
+/* arch/arm/mach-msm/include/mach/idle.S
*
* Idle processing for MSM7K - work around bugs with SWFI.
*
-/* linux/include/asm-arm/arch-msm/board.h
+/* arch/arm/mach-msm/include/mach/board.h
*
* Copyright (C) 2007 Google, Inc.
* Author: Brian Swetland <swetland@google.com>
-/* include/asm-arm/arch-msm7200/debug-macro.S
+/* arch/arm/mach-msm7200/include/mach/debug-macro.S
*
* Copyright (C) 2007 Google, Inc.
* Author: Brian Swetland <swetland@google.com>
*
*/
-#include <asm/hardware.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/hardware.h>
+#include <mach/msm_iomap.h>
.macro addruart,rx
@ see if the MMU is enabled and select appropriate base address
-/* linux/include/asm-arm/arch-msm/dma.h
+/* arch/arm/mach-msm/include/mach/dma.h
*
* Copyright (C) 2007 Google, Inc.
*
#ifndef __ASM_ARCH_MSM_DMA_H
#include <linux/list.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
struct msm_dmov_cmd {
struct list_head list;
-/* include/asm-arm/arch-msm7200/entry-macro.S
+/* arch/arm/mach-msm7200/include/mach/entry-macro.S
*
* Copyright (C) 2007 Google, Inc.
* Author: Brian Swetland <swetland@google.com>
*
*/
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
.macro disable_fiq
.endm
-/* linux/include/asm-arm/arch-msm/hardware.h
+/* arch/arm/mach-msm/include/mach/hardware.h
*
* Copyright (C) 2007 Google, Inc.
*
-/* include/asm-arm/arch-msm/io.h
+/* arch/arm/mach-msm/include/mach/io.h
*
* Copyright (C) 2007 Google, Inc.
*
-/* linux/include/asm-arm/arch-msm/irqs.h
+/* arch/arm/mach-msm/include/mach/irqs.h
*
* Copyright (C) 2007 Google, Inc.
* Author: Brian Swetland <swetland@google.com>
-/* linux/include/asm-arm/arch-msm/memory.h
+/* arch/arm/mach-msm/include/mach/memory.h
*
* Copyright (C) 2007 Google, Inc.
*
-/* linux/include/asm-arm/arch-msm/msm_iomap.h
+/* arch/arm/mach-msm/include/mach/msm_iomap.h
*
* Copyright (C) 2007 Google, Inc.
* Author: Brian Swetland <swetland@google.com>
-/* linux/include/asm-arm/arch-msm/system.h
+/* arch/arm/mach-msm/include/mach/system.h
*
* Copyright (C) 2007 Google, Inc.
*
*
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
void arch_idle(void);
-/* linux/include/asm-arm/arch-msm/timex.h
+/* arch/arm/mach-msm/include/mach/timex.h
*
* Copyright (C) 2007 Google, Inc.
*
-/* linux/include/asm-arm/arch-msm/uncompress.h
+/* arch/arm/mach-msm/include/mach/uncompress.h
*
* Copyright (C) 2007 Google, Inc.
*
-/* linux/include/asm-arm/arch-msm/vmalloc.h
+/* arch/arm/mach-msm/include/mach/vmalloc.h
*
* Copyright (C) 2007 Google, Inc.
*
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/page.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
#include <asm/mach/map.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#define MSM_DEVICE(name) { \
.virtual = MSM_##name##_BASE, \
#include <linux/timer.h>
#include <linux/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
#define VIC_REG(off) (MSM_VIC_BASE + (off))
#include <linux/delay.h>
#include <asm/mach/time.h>
-#include <asm/arch/msm_iomap.h>
+#include <mach/msm_iomap.h>
#include <asm/io.h>
#include <linux/ata_platform.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
#include <asm/plat-orion/cache-feroceon-l2.h>
#include <asm/plat-orion/ehci-orion.h>
#include <asm/plat-orion/orion_nand.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
#include <linux/mv643xx_eth.h>
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include "common.h"
/*
- * include/asm-arm/arch-mv78xx0/debug-macro.S
+ * arch/arm/mach-mv78xx0/include/mach/debug-macro.S
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-mv78xx0/entry-macro.S
+ * arch/arm/mach-mv78xx0/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Marvell MV78xx0 platforms
*
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-mv78xx0/hardware.h
+ * arch/arm/mach-mv78xx0/include/mach/hardware.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-mv78xx0/io.h
+ * arch/arm/mach-mv78xx0/include/mach/io.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-mv78xx0/irqs.h
+ * arch/arm/mach-mv78xx0/include/mach/irqs.h
*
* IRQ definitions for Marvell MV78xx0 SoCs
*
/*
- * linux/include/asm-arm/arch-ep93xx/memory.h
+ * arch/arm/mach-mv78xx0/include/mach/memory.h
*/
#ifndef __ASM_ARCH_MEMORY_H
#define PHYS_OFFSET UL(0x00000000)
-#define __bus_to_virt(x) __phys_to_virt(x)
#define __virt_to_bus(x) __virt_to_phys(x)
+#define __bus_to_virt(x) __phys_to_virt(x)
#endif
/*
- * include/asm-arm/arch-mv78xx0/mv78xx0.h
+ * arch/arm/mach-mv78xx0/include/mach/mv78xx0.h
*
* Generic definitions for Marvell MV78xx0 SoC flavors:
* MV781x0 and MV782x0.
/*
- * include/asm-arm/arch-kirkwood/system.h
+ * arch/arm/mach-mv78xx0/include/mach/system.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/arch/hardware.h>
-#include <asm/arch/kirkwood.h>
+#include <mach/hardware.h>
+#include <mach/mv78xx0.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-mv78xx0/timex.h
+ * arch/arm/mach-mv78xx0/include/mach/timex.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-mv78xx0/uncompress.h
+ * arch/arm/mach-mv78xx0/include/mach/uncompress.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
*/
#include <linux/serial_reg.h>
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE)
--- /dev/null
+/*
+ * arch/arm/mach-mv78xx0/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfe000000
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/pci.h>
-#include <asm/arch/mv78xx0.h>
+#include <mach/mv78xx0.h>
#include <asm/plat-orion/irq.h>
#include "common.h"
#include <linux/module.h>
#include <linux/spinlock.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/common.h>
+#include <mach/clock.h>
+#include <mach/common.h>
#include <asm/div64.h>
-#include <asm/mach-types.h>
#include "crm_regs.h"
#include <linux/io.h>
#include <linux/module.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "crm_regs.h"
#ifndef __ARCH_ARM_MACH_MX2_CRM_REGS_H__
#define __ARCH_ARM_MACH_MX2_CRM_REGS_H__
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
/* Register offsets */
#define CCM_CSCR (IO_ADDRESS(CCM_BASE_ADDR) + 0x0)
#include <linux/platform_device.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Resource definition for the MXC IrDA
#include <linux/mm.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable.h>
#include <asm/mach/map.h>
#include <linux/mtd/map.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-#include <asm/arch/common.h>
-#include <asm/hardware.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/imx-uart.h>
-#include <asm/arch/iomux-mx1-mx2.h>
-#include <asm/arch/board-mx27ads.h>
+#include <mach/gpio.h>
+#include <mach/imx-uart.h>
+#include <mach/iomux-mx1-mx2.h>
+#include <mach/board-mx27ads.h>
/* ADS's NOR flash */
static struct physmap_flash_data mx27ads_flash_data = {
#include <linux/mtd/physmap.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
-#include <asm/arch/common.h>
-#include <asm/hardware.h>
-#include <asm/arch/iomux-mx1-mx2.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+#include <mach/iomux-mx1-mx2.h>
#include <asm/mach/time.h>
-#include <asm/arch/imx-uart.h>
-#include <asm/arch/board-pcm038.h>
+#include <mach/imx-uart.h>
+#include <mach/board-pcm038.h>
/*
* Phytec's phyCORE-i.MX27 comes with 32MiB flash,
*/
#include <linux/platform_device.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
+#include <mach/hardware.h>
#include <asm/mach/arch.h>
/*
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/serial.h>
-#include <asm/hardware.h>
-#include <asm/arch/imx-uart.h>
+#include <mach/hardware.h>
+#include <mach/imx-uart.h>
static struct resource uart0[] = {
{
#include <linux/clk.h>
#include <linux/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/proc-fns.h>
#include <asm/system.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
#include <asm/div64.h>
#include "crm_regs.h"
#include <linux/platform_device.h>
#include <linux/serial.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
-#include <asm/arch/imx-uart.h>
+#include <mach/hardware.h>
+#include <mach/imx-uart.h>
static struct resource uart0[] = {
{
#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/iomux-mx3.h>
+#include <mach/hardware.h>
+#include <mach/gpio.h>
+#include <mach/iomux-mx3.h>
/*
* IOMUX register (base) addresses
#include <linux/mm.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable.h>
#include <asm/mach/map.h>
-#include <asm/arch/common.h>
+#include <mach/common.h>
/*!
* @file mm.c
#include <linux/clk.h>
#include <linux/serial_8250.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/memory.h>
#include <asm/mach/map.h>
-#include <asm/arch/common.h>
-#include <asm/arch/board-mx31ads.h>
+#include <mach/common.h>
+#include <mach/board-mx31ads.h>
/*!
* @file mx31ads.c
#include <linux/kernel.h>
#include <linux/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/arch/common.h>
+#include <mach/common.h>
#include <asm/page.h>
#include <asm/setup.h>
-#include <asm/arch/board-mx31lite.h>
+#include <mach/board-mx31lite.h>
/*
* This file contains the board-specific initialization routines.
#include <linux/mtd/physmap.h>
#include <linux/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/arch/common.h>
-#include <asm/arch/imx-uart.h>
-#include <asm/arch/iomux-mx3.h>
-#include <asm/arch/board-pcm037.h>
+#include <mach/common.h>
+#include <mach/imx-uart.h>
+#include <mach/iomux-mx3.h>
+#include <mach/board-pcm037.h>
static struct physmap_flash_data pcm037_flash_data = {
.width = 2,
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/hardware.h>
+#include <mach/netx-regs.h>
+#include <mach/hardware.h>
struct clk {};
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/map.h>
#include <asm/hardware/vic.h>
#include <asm/io.h>
-#include <asm/arch/netx-regs.h>
+#include <mach/netx-regs.h>
#include <asm/mach/irq.h>
static struct map_desc netx_io_desc[] __initdata = {
-/* linux/include/asm-arm/arch-netx/debug-macro.S
+/* arch/arm/mach-netx/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-netx/dma.h
+ * arch/arm/mach-netx/include/mach/dma.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/entry-macro.S
+ * arch/arm/mach-netx/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Hilscher netX based platforms
*
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-netx/eth.h
+ * arch/arm/mach-netx/include/mach/eth.h
*
* Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/hardware.h
+ * arch/arm/mach-netx/include/mach/hardware.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * linux/include/asm-arm/arch-netx/io.h
+ * arch/arm/mach-netx/include/mach/io.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/irqs.h
+ * arch/arm/mach-netx/include/mach/irqs.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * linux/include/asm-arm/arch-netx/memory.h
+ * arch/arm/mach-netx/include/mach/memory.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/netx-regs.h
+ * arch/arm/mach-netx/include/mach/netx-regs.h
*
* Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * linux/include/asm-arm/arch-netx/param.h
+ * arch/arm/mach-netx/include/mach/param.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/pfifo.h
+ * arch/arm/mach-netx/include/mach/pfifo.h
*
* Copyright (c) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/system.h
+ * arch/arm/mach-netx/include/mach/system.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
#define __ASM_ARCH_SYSTEM_H
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "netx-regs.h"
static inline void arch_idle(void)
/*
- * include/asm-arm/arch-netx/timex.h
+ * arch/arm/mach-netx/include/mach/timex.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * include/asm-arm/arch-netx/uncompress.h
+ * arch/arm/mach-netx/include/mach/uncompress.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * linux/include/asm-arm/arch-netx/vmalloc.h
+ * arch/arm/mach-netx/include/mach/vmalloc.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
/*
- * linux/include/asm-arm/arch-netx/xc.h
+ * arch/arm/mach-netx/include/mach/xc.h
*
* Copyright (C) 2005 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
*
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/arch/eth.h>
+#include <mach/netx-regs.h>
+#include <mach/eth.h>
#include "generic.h"
#include "fb.h"
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/arch/eth.h>
+#include <mach/netx-regs.h>
+#include <mach/eth.h>
#include "generic.h"
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/arch/eth.h>
+#include <mach/netx-regs.h>
+#include <mach/eth.h>
#include "generic.h"
#include "fb.h"
#include <linux/mutex.h>
#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/arch/pfifo.h>
+#include <mach/hardware.h>
+#include <mach/netx-regs.h>
+#include <mach/pfifo.h>
static DEFINE_MUTEX(pfifo_lock);
#include <linux/irq.h>
#include <linux/clocksource.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach/time.h>
-#include <asm/arch/netx-regs.h>
+#include <mach/netx-regs.h>
/*
* IRQ handler for the timer
#include <linux/mutex.h>
#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/netx-regs.h>
+#include <mach/hardware.h>
+#include <mach/netx-regs.h>
-#include <asm/arch/xc.h>
+#include <mach/xc.h>
static DEFINE_MUTEX(xc_lock);
#include <asm/mach/map.h>
#include <asm/gpio.h>
-#include <asm/arch-ns9xxx/board.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
-#include <asm/arch-ns9xxx/regs-sys-ns9360.h>
-#include <asm/arch-ns9xxx/regs-mem.h>
-#include <asm/arch-ns9xxx/regs-bbu.h>
-#include <asm/arch-ns9xxx/regs-board-a9m9750dev.h>
+#include <mach/board.h>
+#include <mach/processor-ns9360.h>
+#include <mach/regs-sys-ns9360.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-bbu.h>
+#include <mach/regs-board-a9m9750dev.h>
#include "board-a9m9750dev.h"
#include <linux/kernel.h>
#include <linux/module.h>
-#include <asm/arch-ns9xxx/regs-bbu.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
+#include <mach/regs-bbu.h>
+#include <mach/processor-ns9360.h>
#include "gpio-ns9360.h"
#include <linux/spinlock.h>
#include <linux/module.h>
-#include <asm/arch-ns9xxx/gpio.h>
-#include <asm/arch-ns9xxx/processor.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
+#include <mach/gpio.h>
+#include <mach/processor.h>
+#include <mach/processor-ns9360.h>
#include <asm/bug.h>
#include <asm/types.h>
#include <asm/bitops.h>
/*
- * include/asm-arm/arch-ns9xxx/board.h
+ * arch/arm/mach-ns9xxx/include/mach/board.h
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/debug-macro.S
+ * arch/arm/mach-ns9xxx/include/mach/debug-macro.S
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
*
* under the terms of the GNU General Public License version 2 as published by
* the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch-ns9xxx/regs-board-a9m9750dev.h>
+#include <mach/regs-board-a9m9750dev.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-ns9xxx/dma.h
+ * arch/arm/mach-ns9xxx/include/mach/dma.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/entry-macro.S
+ * arch/arm/mach-ns9xxx/include/mach/entry-macro.S
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
* under the terms of the GNU General Public License version 2 as published by
* the Free Software Foundation.
*/
-#include <asm/hardware.h>
-#include <asm/arch-ns9xxx/regs-sys-common.h>
+#include <mach/hardware.h>
+#include <mach/regs-sys-common.h>
.macro get_irqnr_preamble, base, tmp
ldr \base, =SYS_ISRADDR
/*
- * include/asm-arm/arch-ns9xxx/gpio.h
+ * arch/arm/mach-ns9xxx/include/mach/gpio.h
*
* Copyright (C) 2007 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/hardware.h
+ * arch/arm/mach-ns9xxx/include/mach/hardware.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/io.h
+ * arch/arm/mach-ns9xxx/include/mach/io.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/irqs.h
+ * arch/arm/mach-ns9xxx/include/mach/irqs.h
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/memory.h
+ * arch/arm/mach-ns9xxx/include/mach/memory.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/module.h
+ * arch/arm/mach-ns9xxx/include/mach/module.h
*
* Copyright (C) 2007 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/processor-ns9360.h
+ * arch/arm/mach-ns9xxx/include/mach/processor-ns9360.h
*
* Copyright (C) 2007 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/processor.h
+ * arch/arm/mach-ns9xxx/include/mach/processor.h
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_PROCESSOR_H
#define __ASM_ARCH_PROCESSOR_H
-#include <asm/arch-ns9xxx/module.h>
+#include <mach/module.h>
#define processor_is_ns9210() (0 \
|| module_is_cc7ucamry() \
/*
- * include/asm-arm/arch-ns9xxx/regs-bbu.h
+ * arch/arm/mach-ns9xxx/include/mach/regs-bbu.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_REGSBBU_H
#define __ASM_ARCH_REGSBBU_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/* BBus Utility */
/*
- * include/asm-arm/arch-ns9xxx/regs-board-a9m9750dev.h
+ * arch/arm/mach-ns9xxx/include/mach/regs-board-a9m9750dev.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_REGSBOARDA9M9750_H
#define __ASM_ARCH_REGSBOARDA9M9750_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define FPGA_UARTA_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0))
#define FPGA_UARTB_BASE io_p2v(NS9XXX_CSxSTAT_PHYS(0) + 0x08)
/*
- * include/asm-arm/arch-ns9xxx/regs-mem.h
+ * arch/arm/mach-ns9xxx/include/mach/regs-mem.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_REGSMEM_H
#define __ASM_ARCH_REGSMEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/* Memory Module */
/*
- * include/asm-arm/arch-ns9xxx/regs-sys-common.h
+ * arch/arm/mach-ns9xxx/include/mach/regs-sys-common.h
*
* Copyright (C) 2007 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_REGSSYSCOMMON_H
#define __ASM_ARCH_REGSSYSCOMMON_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/* Interrupt Vector Address Register Level x */
#define SYS_IVA(x) __REG2(0xa09000c4, (x))
/*
- * include/asm-arm/arch-ns9xxx/regs-sys-ns9360.h
+ * arch/arm/mach-ns9xxx/include/mach/regs-sys-ns9360.h
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
#ifndef __ASM_ARCH_REGSSYSNS9360_H
#define __ASM_ARCH_REGSSYSNS9360_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/* System Control Module */
/*
- * include/asm-arm/arch-ns9xxx/system.h
+ * arch/arm/mach-ns9xxx/include/mach/system.h
*
* Copyright (C) 2006,2007 by Digi International Inc.
* All rights reserved.
#define __ASM_ARCH_SYSTEM_H
#include <asm/proc-fns.h>
-#include <asm/arch-ns9xxx/processor.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
+#include <mach/processor.h>
+#include <mach/processor-ns9360.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-ns9xxx/timex.h
+ * arch/arm/mach-ns9xxx/include/mach/timex.h
*
* Copyright (C) 2005-2006 by Digi International Inc.
* All rights reserved.
#define __ASM_ARCH_TIMEX_H
/*
- * value for CLOCK_TICK_RATE stolen from include/asm-arm/arch-s3c2410/timex.h.
+ * value for CLOCK_TICK_RATE stolen from arch/arm/mach-s3c2410/include/mach/timex.h.
* See there for an explanation.
*/
#define CLOCK_TICK_RATE 12000000
/*
- * include/asm-arm/arch-ns9xxx/uncompress.h
+ * arch/arm/mach-ns9xxx/include/mach/uncompress.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
/*
- * include/asm-arm/arch-ns9xxx/vmalloc.h
+ * arch/arm/mach-ns9xxx/include/mach/vmalloc.h
*
* Copyright (C) 2006 by Digi International Inc.
* All rights reserved.
#include <linux/kernel_stat.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/mach-types.h>
-#include <asm/arch-ns9xxx/regs-sys-common.h>
-#include <asm/arch-ns9xxx/irqs.h>
-#include <asm/arch-ns9xxx/board.h>
+#include <mach/regs-sys-common.h>
+#include <mach/irqs.h>
+#include <mach/board.h>
#include "generic.h"
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
+#include <mach/processor-ns9360.h>
#include "board-a9m9750dev.h"
#include "generic.h"
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
+#include <mach/processor-ns9360.h>
#include "board-jscc9p9360.h"
#include "generic.h"
#include <linux/platform_device.h>
#include <linux/serial_8250.h>
-#include <asm/arch-ns9xxx/regs-board-a9m9750dev.h>
-#include <asm/arch-ns9xxx/board.h>
+#include <mach/regs-board-a9m9750dev.h>
+#include <mach/board.h>
#define DRIVER_NAME "serial8250"
#include <asm/page.h>
#include <asm/mach/map.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
-#include <asm/arch-ns9xxx/regs-sys-ns9360.h>
+#include <mach/processor-ns9360.h>
+#include <mach/regs-sys-ns9360.h>
void ns9360_reset(char mode)
{
#include <linux/clocksource.h>
#include <linux/clockchips.h>
-#include <asm/arch-ns9xxx/processor-ns9360.h>
-#include <asm/arch-ns9xxx/regs-sys-ns9360.h>
-#include <asm/arch-ns9xxx/irqs.h>
-#include <asm/arch/system.h>
+#include <mach/processor-ns9360.h>
+#include <mach/regs-sys-ns9360.h>
+#include <mach/irqs.h>
+#include <mach/system.h>
#include "generic.h"
#define TIMER_CLOCKSOURCE 0
#include <linux/input.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/board-ams-delta.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
+#include <mach/board-ams-delta.h>
+#include <mach/gpio.h>
+#include <mach/keypad.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
+#include <mach/common.h>
static u8 ams_delta_latch1_reg;
static u16 ams_delta_latch2_reg;
#include <linux/mtd/partitions.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/nand.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/board.h>
-#include <asm/arch/board-fsample.h>
+#include <mach/tc.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/fpga.h>
+#include <mach/nand.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/board.h>
+#include <mach/board-fsample.h>
static int fsample_keymap[] = {
KEY(0,0,KEY_UP),
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
+#include <mach/common.h>
static void __init omap_generic_init_irq(void)
{
* published by the Free Software Foundation.
*/
-#include <asm/arch/mmc.h>
-#include <asm/arch/gpio.h>
+#include <mach/mmc.h>
+#include <mach/gpio.h>
#ifdef CONFIG_MMC_OMAP
static int slot_cover_open;
#include <linux/input.h>
#include <linux/i2c/tps65010.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio-switch.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/nand.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/gpio-switch.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
+#include <mach/nand.h>
+#include <mach/irda.h>
+#include <mach/usb.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
static int h2_keymap[] = {
KEY(0, 0, KEY_LEFT),
* published by the Free Software Foundation.
*/
-#include <asm/arch/mmc.h>
-#include <asm/arch/gpio.h>
+#include <mach/mmc.h>
+#include <mach/gpio.h>
#ifdef CONFIG_MMC_OMAP
static int slot_cover_open;
#include <asm/setup.h>
#include <asm/page.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpioexpander.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/nand.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/gpioexpander.h>
+#include <mach/irqs.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
+#include <mach/nand.h>
+#include <mach/irda.h>
+#include <mach/usb.h>
+#include <mach/keypad.h>
+#include <mach/dma.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
#define H3_TS_GPIO 48
#include <linux/mtd/partitions.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/mux.h>
+#include <mach/fpga.h>
+#include <mach/gpio.h>
+#include <mach/tc.h>
+#include <mach/usb.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
static int innovator_keymap[] = {
KEY(0, 0, KEY_F1),
#include <linux/workqueue.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/dsp_common.h>
-#include <asm/arch/aic23.h>
-#include <asm/arch/omapfb.h>
-#include <asm/arch/lcd_mipid.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/dsp_common.h>
+#include <mach/aic23.h>
+#include <mach/omapfb.h>
+#include <mach/lcd_mipid.h>
#define ADS7846_PENDOWN_GPIO 15
#include <linux/i2c/tps65010.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/usb.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
static struct mtd_partition osk_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
-#include <asm/arch/keypad.h>
+#include <mach/keypad.h>
static const int osk_keymap[] = {
/* KEY(col, row, code) */
#include <linux/interrupt.h>
#include <linux/apm-emulation.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/board.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/tc.h>
+#include <mach/dma.h>
+#include <mach/board.h>
+#include <mach/irda.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
static void __init omap_palmte_init_irq(void)
{
#include <linux/mtd/partitions.h>
#include <linux/leds.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/led.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/led.h>
+#include <mach/mcbsp.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/dma.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/irda.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/omap-alsa.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/omap-alsa.h>
+#include <mach/mcbsp.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/dma.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/irda.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/omap-alsa.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/nand.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/common.h>
-#include <asm/arch/board.h>
+#include <mach/tc.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/fpga.h>
+#include <mach/nand.h>
+#include <mach/keypad.h>
+#include <mach/common.h>
+#include <mach/board.h>
static int p2_keymap[] = {
KEY(0,0,KEY_UP),
* published by the Free Software Foundation.
*/
-#include <asm/arch/hardware.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/gpio.h>
+#include <mach/hardware.h>
+#include <mach/mmc.h>
+#include <mach/gpio.h>
#ifdef CONFIG_MMC_OMAP
static int slot_cover_open;
#include <linux/i2c.h>
#include <linux/errno.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/omap-alsa.h>
-#include <asm/arch/keypad.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/irda.h>
+#include <mach/usb.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/mcbsp.h>
+#include <mach/omap-alsa.h>
+#include <mach/keypad.h>
/* Write to I2C device */
int sx1_i2c_write_byte(u8 devaddr, u8 regoffset, u8 value)
#include <linux/serial_8250.h>
#include <linux/serial_reg.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/arch/common.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/usb.h>
+#include <mach/common.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
+#include <mach/usb.h>
static struct plat_serial8250_port voiceblue_ports[] = {
{
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
+#include <mach/cpu.h>
+#include <mach/usb.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
#include "clock.h"
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/gpio.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/mux.h>
+#include <mach/gpio.h>
/*-------------------------------------------------------------------------*/
#include <linux/device.h>
#include <linux/errno.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/gpio.h>
+#include <mach/fpga.h>
+#include <mach/gpio.h>
static void fpga_mask_irq(unsigned int irq)
{
#include <asm/tlb.h>
#include <asm/mach/map.h>
#include <asm/io.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
extern int omap1_clk_init(void);
extern void omap_check_revision(void);
#include <linux/sched.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/cpu.h>
+#include <mach/gpio.h>
+#include <mach/cpu.h>
#include <asm/io.h>
#include <linux/sched.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <asm/mach-types.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/gpio.h>
+#include <mach/fpga.h>
+#include <mach/gpio.h>
#include "leds.h"
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#include "leds.h"
#include <asm/leds.h>
#include <asm/mach-types.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
#include "leds.h"
#include <linux/resource.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
-#include <asm/arch/mailbox.h>
-#include <asm/arch/irqs.h>
+#include <mach/mailbox.h>
+#include <mach/irqs.h>
#include <asm/io.h>
#define MAILBOX_ARM2DSP1 0x00
#include <linux/io.h>
#include <linux/platform_device.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/dsp_common.h>
+#include <mach/dma.h>
+#include <mach/mux.h>
+#include <mach/cpu.h>
+#include <mach/mcbsp.h>
+#include <mach/dsp_common.h>
#define DPS_RSTCT2_PER_EN (1 << 0)
#define DSP_RSTCT2_WD_PER_EN (1 << 1)
#include <asm/io.h>
#include <linux/spinlock.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
#ifdef CONFIG_OMAP_MUX
#include <asm/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <asm/mach-types.h>
-
-#include <asm/arch/cpu.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/dmtimer.h>
+
+#include <mach/cpu.h>
+#include <mach/irqs.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
+#include <mach/tc.h>
+#include <mach/pm.h>
+#include <mach/mux.h>
+#include <mach/dma.h>
+#include <mach/dmtimer.h>
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
static unsigned short dsp_sleep_save[DSP_SLEEP_SAVE_SIZE];
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/fpga.h>
+#include <mach/board.h>
+#include <mach/mux.h>
+#include <mach/gpio.h>
+#include <mach/fpga.h>
#ifdef CONFIG_PM
-#include <asm/arch/pm.h>
+#include <mach/pm.h>
#endif
static struct clk * uart1_ck;
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/arch/pm.h>
+#include <mach/io.h>
+#include <mach/pm.h>
.text
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/hardware.h>
+#include <mach/io.h>
+#include <mach/hardware.h>
.text
#include <linux/clockchips.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <linux/clockchips.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include <asm/arch/dmtimer.h>
+#include <mach/dmtimer.h>
struct sys_timer omap_timer;
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
-#include <asm/arch/gpmc.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/gpmc.h>
#include <asm/io.h>
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/led.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
-#include <asm/arch/gpmc.h>
-#include <asm/arch/control.h>
+#include <mach/gpio.h>
+#include <mach/led.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/gpmc.h>
+#include <mach/control.h>
/* LED & Switch macros */
#define LED0_GPIO13 13
#include <linux/init.h>
#include <linux/device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
+#include <mach/common.h>
static void __init omap_generic_init_irq(void)
{
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
-#include <asm/arch/control.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/gpioexpander.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/board.h>
-#include <asm/arch/common.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/menelaus.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/gpmc.h>
+#include <mach/control.h>
+#include <mach/gpio.h>
+#include <mach/gpioexpander.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/irda.h>
+#include <mach/board.h>
+#include <mach/common.h>
+#include <mach/keypad.h>
+#include <mach/menelaus.h>
+#include <mach/dma.h>
+#include <mach/gpmc.h>
#include <asm/io.h>
#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/cpu.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
+#include <mach/cpu.h>
#include <asm/div64.h>
#include "memory.h"
#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK_H
#define __ARCH_ARM_MACH_OMAP2_CLOCK_H
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
/* The maximum error between a target DPLL rate and the rounded rate in Hz */
#define DEFAULT_DPLL_RATE_TOLERANCE 50000
#include <linux/io.h>
#include <linux/cpufreq.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
#include <asm/div64.h>
#include <asm/bitops.h>
#include <linux/io.h>
#include <linux/limits.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
#include <asm/div64.h>
#include <asm/bitops.h>
#ifndef __ARCH_ARM_MACH_OMAP2_CLOCK34XX_H
#define __ARCH_ARM_MACH_OMAP2_CLOCK34XX_H
-#include <asm/arch/control.h>
+#include <mach/control.h>
#include "clock.h"
#include "cm.h"
#include <linux/kernel.h>
#include <linux/io.h>
-#include <asm/arch/common.h>
-#include <asm/arch/control.h>
+#include <mach/common.h>
+#include <mach/control.h>
static void __iomem *omap2_ctrl_base;
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/gpio.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/mux.h>
+#include <mach/gpio.h>
#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
#if defined(CONFIG_SPI_OMAP24XX)
-#include <asm/arch/mcspi.h>
+#include <mach/mcspi.h>
#define OMAP2_MCSPI1_BASE 0x48098000
#define OMAP2_MCSPI2_BASE 0x4809a000
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/gpmc.h>
+#include <mach/gpmc.h>
#undef DEBUG
#include <asm/io.h>
-#include <asm/arch/control.h>
-#include <asm/arch/cpu.h>
+#include <mach/control.h>
+#include <mach/cpu.h>
#if defined(CONFIG_ARCH_OMAP2420)
#define TAP_BASE io_p2v(0x48014000)
#include <asm/mach/map.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/omapfb.h>
+#include <mach/mux.h>
+#include <mach/omapfb.h>
extern void omap_sram_init(void);
extern int omap2_clk_init(void);
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/irq.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/platform_device.h>
-#include <asm/arch/mailbox.h>
-#include <asm/arch/irqs.h>
+#include <mach/mailbox.h>
+#include <mach/irqs.h>
#include <asm/io.h>
#define MAILBOX_REVISION 0x00
#include <linux/io.h>
#include <linux/platform_device.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/dma.h>
+#include <mach/mux.h>
+#include <mach/cpu.h>
+#include <mach/mcbsp.h>
struct mcbsp_internal_clk {
struct clk clk;
#include <asm/io.h>
-#include <asm/arch/common.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
+#include <mach/common.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
#include "prm.h"
#include <asm/io.h>
#include <linux/spinlock.h>
-#include <asm/arch/control.h>
-#include <asm/arch/mux.h>
+#include <mach/control.h>
+#include <mach/mux.h>
#ifdef CONFIG_OMAP_MUX
#include <asm/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
-#include <asm/mach-types.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/pm.h>
+#include <mach/irqs.h>
+#include <mach/clock.h>
+#include <mach/sram.h>
+#include <mach/pm.h>
static struct clk *vclk;
static void (*omap2_sram_idle)(void);
#include <linux/clk.h>
#include <linux/io.h>
-#include <asm/arch/common.h>
-#include <asm/arch/prcm.h>
+#include <mach/common.h>
+#include <mach/prcm.h>
#include "clock.h"
#include "prm.h"
*/
#undef DEBUG
-#include <asm/arch/sdrc.h>
+#include <mach/sdrc.h>
#ifndef __ASSEMBLER__
extern void __iomem *omap2_sdrc_base;
#include <asm/io.h>
-#include <asm/arch/common.h>
-#include <asm/arch/board.h>
+#include <mach/common.h>
+#include <mach/board.h>
static struct clk * uart1_ick = NULL;
static struct clk * uart1_fck = NULL;
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/arch/pm.h>
+#include <mach/io.h>
+#include <mach/pm.h>
#include "sdrc.h"
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/hardware.h>
+#include <mach/io.h>
+#include <mach/hardware.h>
#include "prm.h"
#include "cm.h"
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/hardware.h>
+#include <mach/io.h>
+#include <mach/hardware.h>
#include "prm.h"
#include "cm.h"
#include <linux/clockchips.h>
#include <asm/mach/time.h>
-#include <asm/arch/dmtimer.h>
+#include <mach/dmtimer.h>
static struct omap_dm_timer *gptimer;
static struct clock_event_device clockevent_gpt;
#include <linux/usb/musb.h>
-#include <asm/arch/gpmc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
+#include <mach/gpmc.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
static u8 async_cs, sync_cs;
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include "common.h"
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/orion5x.h>
+#include <mach/hardware.h>
+#include <mach/orion5x.h>
#include <asm/plat-orion/ehci-orion.h>
#include <asm/plat-orion/orion_nand.h>
#include <asm/plat-orion/time.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include <asm/plat-orion/orion_nand.h>
#include "common.h"
#include "mpp.h"
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include <linux/bitops.h>
#include <asm/gpio.h>
#include <asm/io.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
static DEFINE_SPINLOCK(gpio_lock);
/*
- * include/asm-arm/arch-orion5x/debug-macro.S
+ * arch/arm/mach-orion5x/include/mach/debug-macro.S
*
* Debugging macro include header
*
* published by the Free Software Foundation.
*/
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
/*
- * include/asm-arm/arch-orion5x/entry-macro.S
+ * arch/arm/mach-orion5x/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Orion platforms
*
* warranty of any kind, whether express or implied.
*/
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
.macro disable_fiq
.endm
/*
- * include/asm-arm/arch-orion5x/gpio.h
+ * arch/arm/mach-orion5x/include/mach/gpio.h
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
/*
- * include/asm-arm/arch-orion5x/hardware.h
+ * arch/arm/mach-orion5x/include/mach/hardware.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * include/asm-arm/arch-orion5x/io.h
+ * arch/arm/mach-orion5x/include/mach/io.h
*
* Tzachi Perelstein <tzachi@marvell.com>
*
/*
- * include/asm-arm/arch-orion5x/irqs.h
+ * arch/arm/mach-orion5x/include/mach/irqs.h
*
* IRQ definitions for Orion SoC
*
/*
- * include/asm-arm/arch-orion5x/memory.h
+ * arch/arm/mach-orion5x/include/mach/memory.h
*
* Marvell Orion memory definitions
*/
/*
- * include/asm-arm/arch-orion5x/orion5x.h
+ * arch/arm/mach-orion5x/include/mach/orion5x.h
*
* Generic definitions of Orion SoC flavors:
* Orion-1, Orion-VoIP, Orion-NAS, and Orion-2.
/*
- * include/asm-arm/arch-orion5x/system.h
+ * arch/arm/mach-orion5x/include/mach/system.h
*
* Tzachi Perelstein <tzachi@marvell.com>
*
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/arch/hardware.h>
-#include <asm/arch/orion5x.h>
+#include <mach/hardware.h>
+#include <mach/orion5x.h>
static inline void arch_idle(void)
{
/*
- * include/asm-arm/arch-orion5x/timex.h
+ * arch/arm/mach-orion5x/include/mach/timex.h
*
* Tzachi Perelstein <tzachi@marvell.com>
*
/*
- * include/asm-arm/arch-orion5x/uncompress.h
+ * arch/arm/mach-orion5x/include/mach/uncompress.h
*
* Tzachi Perelstein <tzachi@marvell.com>
*
*/
#include <linux/serial_reg.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE)
--- /dev/null
+/*
+ * arch/arm/mach-orion5x/include/mach/vmalloc.h
+ */
+
+#define VMALLOC_END 0xfd800000
#include <linux/irq.h>
#include <asm/gpio.h>
#include <asm/io.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include <asm/plat-orion/irq.h>
#include "common.h"
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include <asm/plat-orion/orion_nand.h>
#include "common.h"
#include "mpp.h"
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mbus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data rd88f5181l_fxo_eth_data = {
.phy_addr = -1,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
};
static void __init rd88f5181l_fxo_init(void)
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
#include <linux/i2c.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data rd88f5181l_ge_eth_data = {
.phy_addr = -1,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
};
static struct i2c_board_info __initdata rd88f5181l_ge_i2c_rtc = {
#include <asm/leds.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include "tsx09-common.h"
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include "tsx09-common.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data wnr854t_eth_data = {
.phy_addr = -1,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
};
static void __init wnr854t_init(void)
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
-#include <asm/arch/orion5x.h>
+#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data wrt350n_v2_eth_data = {
.phy_addr = -1,
+ .speed = SPEED_1000,
+ .duplex = DUPLEX_FULL,
};
static void __init wrt350n_v2_init(void)
#include <linux/err.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
#include "clock.h"
/*forward declaration*/
#include <linux/device.h>
#include <linux/spi/spi.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/arch/irq.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/dma.h>
+#include <mach/irq.h>
+#include <mach/clock.h>
+#include <mach/dma.h>
struct resource spipnx_0_resources[] = {
{
#include <linux/clk.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
#include <asm/dma-mapping.h>
#include <asm/io.h>
#include <asm/mach/dma.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
static struct dma_channel {
char *name;
#include <linux/kernel.h>
#include <linux/module.h>
#include <asm/io.h>
-#include <asm/arch/platform.h>
-#include <asm/arch/gpio.h>
+#include <mach/platform.h>
+#include <mach/gpio.h>
/* register definitions */
#define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE)
#include <linux/i2c-pnx.h>
#include <linux/platform_device.h>
#include <linux/err.h>
-#include <asm/arch/platform.h>
-#include <asm/arch/i2c.h>
+#include <mach/platform.h>
+#include <mach/i2c.h>
static int set_clock_run(struct platform_device *pdev)
{
/*
- * include/asm-arm/arch-pnx4008/clock.h
+ * arch/arm/mach-pnx4008/include/mach/clock.h
*
* Clock control driver for PNX4008 - header file
*
-/* linux/include/asm-arm/arch-pnx4008/debug-macro.S
+/* arch/arm/mach-pnx4008/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-pnx4008/dma.h
+ * arch/arm/mach-pnx4008/include/mach/dma.h
*
* PNX4008 DMA header file
*
/*
- * include/asm-arm/arch-pnx4008/entry-macro.S
+ * arch/arm/mach-pnx4008/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for PNX4008-based platforms
*
/*
- * include/asm-arm/arch-pnx4008/gpio.h
+ * arch/arm/mach-pnx4008/include/mach/gpio.h
*
* PNX4008 GPIO driver - header file
*
/*
- * linux/include/asm-arm/arch-pnx4008/hardware.h
+ * arch/arm/mach-pnx4008/include/mach/hardware.h
*
* Copyright (c) 2005 MontaVista Software, Inc. <source@mvista.com>
*
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/* Start of virtual addresses for IO devices */
#define IO_BASE 0xF0000000
#ifndef __ASM_ARCH_I2C_H__
#define __ASM_ARCH_I2C_H__
-#include <linux/pm.h>
-#include <linux/platform_device.h>
-
enum {
mstatus_tdi = 0x00000001,
mstatus_afi = 0x00000002,
/*
- * include/asm-arm/arch-pnx4008/io.h
+ * arch/arm/mach-pnx4008/include/mach/io.h
*
* Author: Dmitry Chigirev <chigirev@ru.mvista.com>
*
/*
- * include/asm-arm/arch-pnx4008/irq.h
+ * arch/arm/mach-pnx4008/include/mach/irq.h
*
* PNX4008 IRQ controller driver - header file
* this one is used in entry-arnv.S as well so it cannot contain C code
/*
- * include/asm-arm/arch-pnx4008/irqs.h
+ * arch/arm/mach-pnx4008/include/mach/irqs.h
*
* PNX4008 IRQ controller driver - header file
*
/*
- * linux/include/asm-arm/arch-pnx4008/memory.h
+ * arch/arm/mach-pnx4008/include/mach/memory.h
*
* Copyright (c) 2005 Philips Semiconductors
* Copyright (c) 2005 MontaVista Software, Inc.
/*
- * linux/include/asm-arm/arch-pnx4008/param.h
+ * arch/arm/mach-pnx4008/include/mach/param.h
*
* Copyright (C) 1999 ARM Limited
*
/*
- * include/asm-arm/arch-pnx4008/platform.h
+ * arch/arm/mach-pnx4008/include/mach/platform.h
*
* PNX4008 Base addresses - header file
*
/*
- * include/asm-arm/arch-pnx4008/pm.h
+ * arch/arm/mach-pnx4008/include/mach/pm.h
*
* PNX4008 Power Management Routiness - header file
*
/*
- * linux/include/asm-arm/arch-pnx4008/system.h
+ * arch/arm/mach-pnx4008/include/mach/system.h
*
* Copyright (C) 2003 Philips Semiconductors
* Copyright (C) 2005 MontaVista Software, Inc.
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
static void arch_idle(void)
{
/*
- * include/asm-arm/arch-pnx4008/timex.h
+ * arch/arm/mach-pnx4008/include/mach/timex.h
*
* PNX4008 timers header file
*
#ifndef __PNX4008_TIMEX_H
#define __PNX4008_TIMEX_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#define CLOCK_TICK_RATE 1000000
/*
- * linux/include/asm-arm/arch-pnx4008/uncompress.h
+ * arch/arm/mach-pnx4008/include/mach/uncompress.h
*
* Copyright (C) 1999 ARM Limited
* Copyright (C) 2006 MontaVista Software, Inc.
/*
- * include/asm-arm/arch-pnx4008/vmalloc.h
+ * arch/arm/mach-pnx4008/include/mach/vmalloc.h
*
* Author: Vitaly Wool <source@mvista.com>
*
#include <linux/ioport.h>
#include <linux/device.h>
#include <linux/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/mach-types.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/arch/irq.h>
+#include <mach/irq.h>
static u8 pnx4008_irq_type[NR_IRQS] = PNX4008_IRQ_TYPES;
#include <linux/clk.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
#include <asm/cacheflush.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/clock.h>
+#include <mach/pm.h>
+#include <mach/clock.h>
#define SRAM_VA IO_ADDRESS(PNX4008_IRAM_BASE)
#include <asm/io.h>
-#include <asm/arch/platform.h>
-#include <asm/hardware.h>
+#include <mach/platform.h>
+#include <mach/hardware.h>
#include <linux/serial_core.h>
#include <linux/serial_reg.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
#define UART_3 0
#define UART_4 1
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE)
#define PWR_CTRL_REG_OFFS 0x44
#include <linux/irq.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/leds.h>
#include <asm/mach/time.h>
#include <linux/i2c.h>
#include <linux/slab.h>
#include <linux/workqueue.h>
-#include <asm/arch/akita.h>
+#include <mach/akita.h>
/* MAX7310 Regiser Map */
#define MAX7310_INPUT 0x00
#include <linux/platform_device.h>
#include <linux/delay.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/hardware.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/hardware.h>
#include "devices.h"
#include "generic.h"
#include <linux/gpio.h>
#include <asm/mach/pci.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include <asm/mach-types.h>
#include <asm/hardware/it8152.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/bitfield.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/pxa-regs.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/ohci.h>
+#include <mach/mmc.h>
+#include <mach/bitfield.h>
#include <asm/hardware/it8152.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/colibri.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/colibri.h>
#include "generic.h"
#include "devices.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/corgi.h>
-#include <asm/arch/sharpsl.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/irda.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/corgi.h>
+#include <mach/sharpsl.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/scoop.h>
#include <linux/platform_device.h>
#include <linux/module.h>
#include <linux/string.h>
-#include <asm/arch/akita.h>
-#include <asm/arch/corgi.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/sharpsl.h>
-#include <asm/arch/spitz.h>
+#include <mach/akita.h>
+#include <mach/corgi.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/sharpsl.h>
+#include <mach/spitz.h>
#include <asm/hardware/scoop.h>
#include <asm/mach/sharpsl_param.h>
#include "generic.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/scoop.h>
-#include <asm/arch/sharpsl.h>
-#include <asm/arch/corgi.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/sharpsl.h>
+#include <mach/corgi.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
#include "sharpsl.h"
#define SHARPSL_CHARGE_ON_VOLT 0x99 /* 2.9V */
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/ssp.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/regs-ssp.h>
+#include <mach/ssp.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/regs-ssp.h>
#include "sharpsl.h"
static DEFINE_SPINLOCK(corgi_ssp_lock);
#include <linux/init.h>
#include <linux/cpufreq.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
#ifdef DEBUG
static unsigned int freq_debug;
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pxa27x_keypad.h>
-#include <asm/arch/pxa2xx_spi.h>
-#include <asm/arch/camera.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxa3xx_nand.h>
+#include <mach/gpio.h>
+#include <mach/udc.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/irda.h>
+#include <mach/i2c.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/ohci.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/pxa2xx_spi.h>
+#include <mach/camera.h>
+#include <mach/audio.h>
+#include <mach/pxa3xx_nand.h>
#include "devices.h"
#include "generic.h"
#include <asm/system.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
struct dma_channel {
char *name;
#include <linux/module.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxafb.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxafb.h>
static struct pxafb_mode_info e400_pxafb_mode_info = {
.pixclock = 140703,
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa27x-udc.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/pxa27x_keypad.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/ohci.h>
+#include <mach/mmc.h>
+#include <mach/pxa27x_keypad.h>
#include "generic.h"
#include <asm/setup.h>
#include <asm/mach/arch.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include "generic.h"
#include <linux/init.h>
#include <linux/device.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/eseries-gpio.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/udc.h>
+#include <mach/eseries-gpio.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <linux/pwm_backlight.h>
#include <asm/setup.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/i2c.h>
+#include <mach/pxafb.h>
+#include <mach/ohci.h>
+#include <mach/i2c.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/pgtable.h>
#include <asm/mach/map.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
+#include <mach/reset.h>
#include "generic.h"
+void clear_reset_status(unsigned int mask)
+{
+ if (cpu_is_pxa2xx())
+ pxa2xx_clear_reset_status(mask);
+
+ if (cpu_is_pxa3xx())
+ pxa3xx_clear_reset_status(mask);
+}
+
/*
* Get the clock frequency as reflected by CCCR and the turbo flag.
* We assume these values have been applied via a fcs.
#define pxa27x_get_memclk_frequency_10khz() (0)
#endif
+#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x)
+extern void pxa2xx_clear_reset_status(unsigned int);
+#else
+static inline void pxa2xx_clear_reset_status(unsigned int mask) {}
+#endif
+
#ifdef CONFIG_PXA3xx
extern unsigned pxa3xx_get_clk_frequency_khz(int);
extern unsigned pxa3xx_get_memclk_frequency_10khz(void);
+extern void pxa3xx_clear_reset_status(unsigned int);
#else
#define pxa3xx_get_clk_frequency_khz(x) (0)
#define pxa3xx_get_memclk_frequency_10khz() (0)
+static inline void pxa3xx_clear_reset_status(unsigned int mask) {}
#endif
extern struct sysdev_class pxa_irq_sysclass;
#include <linux/sysdev.h>
#include <asm/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
#include "generic.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/gumstix.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/gumstix.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
#include "generic.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/idp.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/bitfield.h>
-#include <asm/arch/mmc.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/idp.h>
+#include <mach/pxafb.h>
+#include <mach/bitfield.h>
+#include <mach/mmc.h>
#include "generic.h"
#include "devices.h"
-/* linux/include/asm-arm/arch-pxa/debug-macro.S
+/* arch/arm/mach-pxa/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-pxa/dma.h
+ * arch/arm/mach-pxa/include/mach/dma.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
/*
- * include/asm-arm/arch-pxa/entry-macro.S
+ * arch/arm/mach-pxa/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for PXA-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
.macro disable_fiq
.endm
/*
- * linux/include/asm-arm/arch-pxa/gpio.h
+ * arch/arm/mach-pxa/include/mach/gpio.h
*
* PXA GPIO wrappers for arch-neutral GPIO calls
*
#ifndef __ASM_ARCH_PXA_GPIO_H
#define __ASM_ARCH_PXA_GPIO_H
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm-generic/gpio.h>
/*
- * linux/include/asm-arm/arch-pxa/gumstix.h
+ * arch/arm/mach-pxa/include/mach/gumstix.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * linux/include/asm-arm/arch-pxa/hardware.h
+ * arch/arm/mach-pxa/include/mach/hardware.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
*/
extern unsigned int get_memclk_frequency_10khz(void);
-/*
- * register GPIO as reset generator
- */
-extern int init_gpio_reset(int gpio);
-
#endif
#if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI)
/*
- * linux/include/asm-arm/arch-pxa/idp.h
+ * arch/arm/mach-pxa/include/mach/idp.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * linux/include/asm-arm/arch-pxa/io.h
+ * arch/arm/mach-pxa/include/mach/io.h
*
* Copied from asm/arch/sa1100/io.h
*/
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-pxa/irqs.h
+ * arch/arm/mach-pxa/include/mach/irqs.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
/*
- * include/asm-arm/arch-pxa/lpd270.h
+ * arch/arm/mach-pxa/include/mach/lpd270.h
*
* Author: Lennert Buytenhek
* Created: Feb 10, 2006
/*
- * linux/include/asm-arm/arch-pxa/lubbock.h
+ * arch/arm/mach-pxa/include/mach/lubbock.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
#ifndef _MAGICIAN_H_
#define _MAGICIAN_H_
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
/*
* PXA GPIOs
/*
- * linux/include/asm-arm/arch-pxa/mainstone.h
+ * arch/arm/mach-pxa/include/mach/mainstone.h
*
* Author: Nicolas Pitre
* Created: Nov 14, 2002
/*
- * linux/include/asm-arm/arch-pxa/memory.h
+ * arch/arm/mach-pxa/include/mach/memory.h
*
* Author: Nicolas Pitre
* Copyright: (C) 2001 MontaVista Software Inc.
#ifndef __ASM_ARCH_MFP_PXA25X_H
#define __ASM_ARCH_MFP_PXA25X_H
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa2xx.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa2xx.h>
/* GPIO */
#define GPIO2_GPIO MFP_CFG_IN(GPIO2, AF0)
* specific controller, and this should work in most cases.
*/
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa2xx.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa2xx.h>
/* GPIO */
#define GPIO85_GPIO MFP_CFG_IN(GPIO85, AF0)
#ifndef __ASM_ARCH_MFP_PXA2XX_H
#define __ASM_ARCH_MFP_PXA2XX_H
-#include <asm/arch/mfp.h>
+#include <mach/mfp.h>
/*
* the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx:
/*
- * linux/include/asm-arm/arch-pxa/mfp-pxa300.h
+ * arch/arm/mach-pxa/include/mach/mfp-pxa300.h
*
* PXA300/PXA310 specific MFP configuration definitions
*
#ifndef __ASM_ARCH_MFP_PXA300_H
#define __ASM_ARCH_MFP_PXA300_H
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa3xx.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa3xx.h>
/* GPIO */
#define GPIO46_GPIO MFP_CFG(GPIO46, AF1)
/*
- * linux/include/asm-arm/arch-pxa/mfp-pxa320.h
+ * arch/arm/mach-pxa/include/mach/mfp-pxa320.h
*
* PXA320 specific MFP configuration definitions
*
#ifndef __ASM_ARCH_MFP_PXA320_H
#define __ASM_ARCH_MFP_PXA320_H
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa3xx.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa3xx.h>
/* GPIO */
#define GPIO46_GPIO MFP_CFG(GPIO46, AF0)
/*
- * linux/include/asm-arm/arch-pxa/mfp-pxa930.h
+ * arch/arm/mach-pxa/include/mach/mfp-pxa930.h
*
* PXA930 specific MFP configuration definitions
*
#ifndef __ASM_ARCH_MFP_PXA9xx_H
#define __ASM_ARCH_MFP_PXA9xx_H
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa3xx.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa3xx.h>
/* GPIO */
#define GPIO46_GPIO MFP_CFG(GPIO46, AF0)
/*
- * linux/include/asm-arm/arch-pxa/mfp.h
+ * arch/arm/mach-pxa/include/mach/mfp.h
*
* Multi-Function Pin Definitions
*
#ifndef __ARCH_PXA_MTD_XIP_H__
#define __ARCH_PXA_MTD_XIP_H__
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#define xip_irqpending() (ICIP & ICMR)
/*
- * linux/include/asm-arm/arch-pxa/pcm027.h
+ * arch/arm/mach-pxa/include/mach/pcm027.h
*
* (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
* (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
/*
- * include/asm-arm/arch-pxa/pcm990_baseboard.h
+ * arch/arm/mach-pxa/include/mach/pcm990_baseboard.h
*
* (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
* (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <asm/arch/pcm027.h>
+#include <mach/pcm027.h>
/*
* definitions relevant only when the PCM-990
/*
- * linux/include/asm-arm/arch-pxa/poodle.h
+ * arch/arm/mach-pxa/include/mach/poodle.h
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
* Based on:
- * linux/include/asm-arm/arch-sa1100/collie.h
+ * arch/arm/mach-sa1100/include/mach/collie.h
*
* ChangeLog:
* 04-06-2001 Lineo Japan, Inc.
/*
- * linux/include/asm-arm/arch-pxa/pxa-regs.h
+ * arch/arm/mach-pxa/include/mach/pxa-regs.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
*/
/*
- * SSP Serial Port Registers - see include/asm-arm/arch-pxa/regs-ssp.h
+ * SSP Serial Port Registers - see arch/arm/mach-pxa/include/mach/regs-ssp.h
*/
/*
*/
/*
- * Core Clock - see include/asm-arm/arch-pxa/pxa2xx-regs.h
+ * Core Clock - see arch/arm/mach-pxa/include/mach/pxa2xx-regs.h
*/
#ifdef CONFIG_PXA27x
/*
- * linux/include/asm-arm/arch-pxa/pxa2xx-regs.h
+ * arch/arm/mach-pxa/include/mach/pxa2xx-regs.h
*
* Taken from pxa-regs.h by Russell King
*
/*
- * linux/include/asm-arm/arch-pxa/pxa3xx-regs.h
+ * arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
*
* PXA3xx specific register definitions
*
/*
- * linux/include/asm-arm/arch-pxa/pxafb.h
+ * arch/arm/mach-pxa/include/mach/pxafb.h
*
* Support for the xscale frame buffer.
*
*/
#include <linux/fb.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-lcd.h>
/*
* Supported LCD connections
#ifndef __ASM_ARCH_REGS_LCD_H
#define __ASM_ARCH_REGS_LCD_H
-#include <asm/arch/bitfield.h>
+#include <mach/bitfield.h>
/*
* LCD Controller Registers and Bits Definitions
--- /dev/null
+#ifndef __ASM_ARCH_RESET_H
+#define __ASM_ARCH_RESET_H
+
+#define RESET_STATUS_HARDWARE (1 << 0) /* Hardware Reset */
+#define RESET_STATUS_WATCHDOG (1 << 1) /* Watchdog Reset */
+#define RESET_STATUS_LOWPOWER (1 << 2) /* Low Power/Sleep Exit */
+#define RESET_STATUS_GPIO (1 << 3) /* GPIO Reset */
+#define RESET_STATUS_ALL (0xf)
+
+extern unsigned int reset_status;
+extern void clear_reset_status(unsigned int mask);
+
+/*
+ * register GPIO as reset generator
+ */
+extern int init_gpio_reset(int gpio);
+
+#endif /* __ASM_ARCH_RESET_H */
/*
- * linux/include/asm-arm/arch-pxa/system.h
+ * arch/arm/mach-pxa/include/mach/system.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
/*
- * linux/include/asm-arm/arch-pxa/timex.h
+ * arch/arm/mach-pxa/include/mach/timex.h
*
* Author: Nicolas Pitre
* Created: Jun 15, 2001
/*
- * linux/include/asm-arm/arch-pxa/udc.h
+ * arch/arm/mach-pxa/include/mach/udc.h
*
*/
#include <asm/mach/udc_pxa2xx.h>
/*
- * linux/include/asm-arm/arch-pxa/uncompress.h
+ * arch/arm/mach-pxa/include/mach/uncompress.h
*
* Author: Nicolas Pitre
* Copyright: (C) 2001 MontaVista Software Inc.
*/
#include <linux/serial_reg.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include <asm/mach-types.h>
#define __REG(x) ((volatile unsigned long *)x)
/*
- * linux/include/asm-arm/arch-pxa/vmalloc.h
+ * arch/arm/mach-pxa/include/mach/vmalloc.h
*
* Author: Nicolas Pitre
* Copyright: (C) 2001 MontaVista Software Inc.
#include <linux/interrupt.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include "generic.h"
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/idp.h>
+#include <mach/pxa-regs.h>
+#include <mach/idp.h>
#include "leds.h"
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/lubbock.h>
+#include <mach/pxa-regs.h>
+#include <mach/lubbock.h>
#include "leds.h"
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mainstone.h>
+#include <mach/pxa-regs.h>
+#include <mach/mainstone.h>
#include "leds.h"
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/types.h>
#include <asm/leds.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/trizeps4.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/trizeps4.h>
#include "leds.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mfp-pxa300.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/ssp.h>
-#include <asm/arch/pxa27x_keypad.h>
-#include <asm/arch/pxa3xx_nand.h>
-#include <asm/arch/littleton.h>
+#include <mach/pxa-regs.h>
+#include <mach/mfp-pxa300.h>
+#include <mach/gpio.h>
+#include <mach/pxafb.h>
+#include <mach/ssp.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/pxa3xx_nand.h>
+#include <mach/littleton.h>
#include "generic.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/lpd270.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/ohci.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/lpd270.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
#include "generic.h"
#include "devices.h"
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
-#include <asm/arch/pxa2xx_spi.h>
+#include <mach/pxa2xx_spi.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/hardware/sa1111.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa25x.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/lubbock.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mmc.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/audio.h>
+#include <mach/lubbock.h>
+#include <mach/udc.h>
+#include <mach/irda.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
#include "generic.h"
#include "devices.h"
* for the temperature sensors.
*/
static struct pxa2xx_spi_master pxa_ssp_master_info = {
- .num_chipselect = 0,
+ .num_chipselect = 1,
};
static int lubbock_ads7846_pendown_state(void)
#include <linux/pda_power.h>
#include <linux/pwm_backlight.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/magician.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/ohci.h>
+#include <mach/magician.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxafb.h>
+#include <mach/i2c.h>
+#include <mach/mmc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
#include "devices.h"
#include "generic.h"
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/mainstone.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pxa27x_keypad.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/mainstone.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/i2c.h>
+#include <mach/mmc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
+#include <mach/pxa27x_keypad.h>
#include "generic.h"
#include "devices.h"
#include <linux/init.h>
#include <linux/sysdev.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa2xx.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa2xx.h>
#include "generic.h"
#include <linux/io.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
-#include <asm/arch/mfp.h>
-#include <asm/arch/mfp-pxa3xx.h>
-#include <asm/arch/pxa3xx-regs.h>
+#include <mach/hardware.h>
+#include <mach/mfp.h>
+#include <mach/mfp-pxa3xx.h>
+#include <mach/pxa3xx-regs.h>
/* mfp_spin_lock is used to ensure that MFP register configuration
* (most likely a read-modify-write operation) is atomic, and that
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/palmtx.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/pxa27x_keypad.h>
-#include <asm/arch/udc.h>
+#include <mach/audio.h>
+#include <mach/palmtx.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/pxa-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/irda.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/udc.h>
#include "generic.h"
#include "devices.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx_spi.h>
-#include <asm/arch/pcm027.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx_spi.h>
+#include <mach/pcm027.h>
#include "generic.h"
/*
#include <linux/irq.h>
#include <linux/platform_device.h>
-#include <linux/ide.h>
#include <linux/i2c.h>
#include <linux/pwm_backlight.h>
#include <media/soc_camera.h>
#include <asm/gpio.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/camera.h>
+#include <mach/i2c.h>
+#include <mach/camera.h>
#include <asm/mach/map.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pcm990_baseboard.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mfp-pxa27x.h>
+#include <mach/pxa-regs.h>
+#include <mach/audio.h>
+#include <mach/mmc.h>
+#include <mach/ohci.h>
+#include <mach/pcm990_baseboard.h>
+#include <mach/pxafb.h>
+#include <mach/mfp-pxa27x.h>
#include "devices.h"
#include "generic.h"
#include <linux/errno.h>
#include <linux/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/memory.h>
#include <asm/system.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/lubbock.h>
+#include <mach/pm.h>
+#include <mach/pxa-regs.h>
+#include <mach/lubbock.h>
#include <asm/mach/time.h>
struct pxa_cpu_pm_fns *pxa_cpu_pm_fns;
#include <linux/pm.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/poodle.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/sharpsl.h>
-#include <asm/arch/ssp.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/irda.h>
+#include <mach/poodle.h>
+#include <mach/pxafb.h>
+#include <mach/sharpsl.h>
+#include <mach/ssp.h>
#include <asm/hardware/scoop.h>
#include <asm/hardware/locomo.h>
#include <linux/pwm.h>
#include <asm/div64.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
/* PWM registers and bits definitions */
#define PWMCR (0x00)
#include <linux/suspend.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa25x.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/dma.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/reset.h>
+#include <mach/pm.h>
+#include <mach/dma.h>
#include "generic.h"
#include "devices.h"
clks_register(&pxa25x_hwuart_clk, 1);
if (cpu_is_pxa21x() || cpu_is_pxa25x()) {
+
+ reset_status = RCSR;
+
clks_register(pxa25x_clks, ARRAY_SIZE(pxa25x_clks));
if ((ret = pxa_init_dma(16)))
#include <linux/platform_device.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa27x.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/i2c.h>
+#include <mach/irqs.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/reset.h>
+#include <mach/ohci.h>
+#include <mach/pm.h>
+#include <mach/dma.h>
+#include <mach/i2c.h>
#include "generic.h"
#include "devices.h"
int i, ret = 0;
if (cpu_is_pxa27x()) {
+
+ reset_status = RCSR;
+
clks_register(pxa27x_clks, ARRAY_SIZE(pxa27x_clks));
if ((ret = pxa_init_dma(32)))
#include <linux/kernel.h>
#include <linux/device.h>
-#include <asm/arch/mfp-pxa2xx.h>
-#include <asm/arch/mfp-pxa25x.h>
-#include <asm/arch/irda.h>
+#include <mach/hardware.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa2xx.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/reset.h>
+#include <mach/irda.h>
+
+void pxa2xx_clear_reset_status(unsigned int mask)
+{
+ /* RESET_STATUS_* has a 1:1 mapping with RCSR */
+ RCSR = mask;
+}
static unsigned long pxa2xx_mfp_fir[] = {
GPIO46_FICP_RXD,
#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa3xx-regs.h>
-#include <asm/arch/mfp-pxa300.h>
+#include <mach/hardware.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/mfp-pxa300.h>
#include "generic.h"
#include "devices.h"
#include <linux/kernel.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
-#include <asm/arch/mfp.h>
-#include <asm/arch/pxa3xx-regs.h>
-#include <asm/arch/mfp-pxa320.h>
+#include <mach/hardware.h>
+#include <mach/mfp.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/mfp-pxa320.h>
#include "generic.h"
#include "devices.h"
#include <linux/io.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa3xx-regs.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/ssp.h>
+#include <mach/hardware.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/reset.h>
+#include <mach/ohci.h>
+#include <mach/pm.h>
+#include <mach/dma.h>
+#include <mach/ssp.h>
#include "generic.h"
#include "devices.h"
return (clk / 10000);
}
+void pxa3xx_clear_reset_status(unsigned int mask)
+{
+ /* RESET_STATUS_* has a 1:1 mapping with ARSR */
+ ARSR = mask;
+}
+
/*
* Return the current AC97 clock frequency.
*/
int i, ret = 0;
if (cpu_is_pxa3xx()) {
+
+ reset_status = ARSR;
+
/*
* clear RDH bit every time after reset
*
#include <linux/irq.h>
#include <linux/dma-mapping.h>
-#include <asm/hardware.h>
-#include <asm/arch/mfp-pxa930.h>
+#include <mach/hardware.h>
+#include <mach/mfp-pxa930.h>
static struct pxa3xx_mfp_addr_map pxa930_mfp_addr_map[] __initdata = {
#include <asm/io.h>
#include <asm/proc-fns.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/pxa-regs.h>
+#include <mach/reset.h>
+
+unsigned int reset_status;
+EXPORT_SYMBOL(reset_status);
static void do_hw_reset(void);
void arch_reset(char mode)
{
- if (cpu_is_pxa2xx())
- RCSR = RCSR_HWR | RCSR_WDR | RCSR_SMR | RCSR_GPR;
+ clear_reset_status(RESET_STATUS_ALL);
switch (mode) {
case 's':
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa3xx-regs.h>
-#include <asm/arch/mfp-pxa930.h>
+#include <mach/hardware.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/mfp-pxa930.h>
#include "devices.h"
#include "generic.h"
#include <linux/platform_device.h>
#include <linux/apm-emulation.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/sharpsl.h>
+#include <mach/pm.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/sharpsl.h>
#include "sharpsl.h"
struct battery_thresh spitz_battery_levels_acin[] = {
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
#define MDREFR_KDIV 0x200a4000 // all banks
#define CCCR_SLEEP 0x00000107 // L=7 2N=2 A=0 PPDIS=0 CPDIS=0
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/pxa27x-udc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/ohci.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/akita.h>
-#include <asm/arch/spitz.h>
-#include <asm/arch/sharpsl.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/reset.h>
+#include <mach/irda.h>
+#include <mach/mmc.h>
+#include <mach/ohci.h>
+#include <mach/udc.h>
+#include <mach/pxafb.h>
+#include <mach/akita.h>
+#include <mach/spitz.h>
+#include <mach/sharpsl.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/scoop.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/scoop.h>
-#include <asm/arch/sharpsl.h>
-#include <asm/arch/spitz.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/sharpsl.h>
+#include <mach/spitz.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
#include "sharpsl.h"
#define SHARPSL_CHARGE_ON_VOLT 0x99 /* 2.9V */
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/arch/ssp.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/regs-ssp.h>
+#include <mach/hardware.h>
+#include <mach/ssp.h>
+#include <mach/pxa-regs.h>
+#include <mach/regs-ssp.h>
#define TIMEOUT 100000
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
.text
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa3xx-regs.h>
-#include <asm/arch/mfp-pxa930.h>
+#include <mach/hardware.h>
+#include <mach/pxa3xx-regs.h>
+#include <mach/mfp-pxa930.h>
#include "devices.h"
#include "generic.h"
#include <asm/cnt32_to_63.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include <asm/mach-types.h>
/*
#include <linux/delay.h>
#include <linux/rfkill.h>
-#include <asm/arch/tosa_bt.h>
+#include <mach/tosa_bt.h>
static void tosa_bt_on(struct tosa_bt_data *data)
{
#include <asm/setup.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/mfp-pxa25x.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/udc.h>
-#include <asm/arch/tosa_bt.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/reset.h>
+#include <mach/irda.h>
+#include <mach/i2c.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/tosa_bt.h>
#include <asm/mach/arch.h>
-#include <asm/arch/tosa.h>
+#include <mach/tosa.h>
#include <asm/hardware/scoop.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/trizeps4.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/ohci.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/trizeps4.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
#include "generic.h"
#include "devices.h"
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/hardware.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/pxafb.h>
-#include <asm/arch/zylonite.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/pxa27x_keypad.h>
-#include <asm/arch/pxa3xx_nand.h>
+#include <mach/hardware.h>
+#include <mach/audio.h>
+#include <mach/gpio.h>
+#include <mach/pxafb.h>
+#include <mach/zylonite.h>
+#include <mach/mmc.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/pxa3xx_nand.h>
#include "devices.h"
#include "generic.h"
#include <linux/i2c/pca953x.h>
#include <asm/gpio.h>
-#include <asm/arch/mfp-pxa300.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/zylonite.h>
+#include <mach/mfp-pxa300.h>
+#include <mach/i2c.h>
+#include <mach/zylonite.h>
#include "generic.h"
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mfp-pxa320.h>
-#include <asm/arch/zylonite.h>
+#include <mach/gpio.h>
+#include <mach/mfp-pxa320.h>
+#include <mach/zylonite.h>
#include "generic.h"
#include <linux/clockchips.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
/*
- * include/asm-arm/arch-realview/board-eb.h
+ * arch/arm/mach-realview/include/mach/board-eb.h
*
* Copyright (C) 2007 ARM Limited
*
#ifndef __ASM_ARCH_BOARD_EB_H
#define __ASM_ARCH_BOARD_EB_H
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* RealView EB + ARM11MPCore peripheral addresses
/*
- * include/asm-arm/arch-realview/board-pb1176.h
+ * arch/arm/mach-realview/include/mach/board-pb1176.h
*
* Copyright (C) 2008 ARM Limited
*
#ifndef __ASM_ARCH_BOARD_PB1176_H
#define __ASM_ARCH_BOARD_PB1176_H
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* Peripheral addresses
/*
- * include/asm-arm/arch-realview/board-pb11mp.h
+ * arch/arm/mach-realview/include/mach/board-pb11mp.h
*
* Copyright (C) 2008 ARM Limited
*
#ifndef __ASM_ARCH_BOARD_PB11MP_H
#define __ASM_ARCH_BOARD_PB11MP_H
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* Peripheral addresses
-/* linux/include/asm-arm/arch-realview/debug-macro.S
+/* arch/arm/mach-realview/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-realview/dma.h
+ * arch/arm/mach-realview/include/mach/dma.h
*
* Copyright (C) 2003 ARM Limited.
* Copyright (C) 1997,1998 Russell King
/*
- * include/asm-arm/arch-realview/entry-macro.S
+ * arch/arm/mach-realview/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for RealView platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/gic.h>
.macro disable_fiq
/*
- * linux/include/asm-arm/arch-realview/hardware.h
+ * arch/arm/mach-realview/include/mach/hardware.h
*
* This file contains the hardware definitions of the RealView boards.
*
/*
- * linux/include/asm-arm/arch-realview/io.h
+ * arch/arm/mach-realview/include/mach/io.h
*
* Copyright (C) 2003 ARM Limited
*
/*
- * linux/include/asm-arm/arch-realview/irqs.h
+ * arch/arm/mach-realview/include/mach/irqs.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
#ifndef __ASM_ARCH_IRQS_H
#define __ASM_ARCH_IRQS_H
-#include <asm/arch/board-eb.h>
-#include <asm/arch/board-pb11mp.h>
-#include <asm/arch/board-pb1176.h>
+#include <mach/board-eb.h>
+#include <mach/board-pb11mp.h>
+#include <mach/board-pb1176.h>
#define IRQ_LOCALTIMER 29
#define IRQ_LOCALWDOG 30
/*
- * linux/include/asm-arm/arch-realview/memory.h
+ * arch/arm/mach-realview/include/mach/memory.h
*
* Copyright (C) 2003 ARM Limited
*
/*
- * linux/include/asm-arm/arch-realview/platform.h
+ * arch/arm/mach-realview/include/mach/platform.h
*
* Copyright (c) ARM Limited 2003. All rights reserved.
*
/*
- * linux/include/asm-arm/arch-realview/system.h
+ * arch/arm/mach-realview/include/mach/system.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-realview/timex.h
+ * arch/arm/mach-realview/include/mach/timex.h
*
* RealView architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-realview/uncompress.h
+ * arch/arm/mach-realview/include/mach/uncompress.h
*
* Copyright (C) 2003 ARM Limited
*
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/board-eb.h>
-#include <asm/arch/board-pb11mp.h>
-#include <asm/arch/board-pb1176.h>
+#include <mach/board-eb.h>
+#include <mach/board-pb11mp.h>
+#include <mach/board-pb1176.h>
#define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00))
#define AMBA_UART_LCRH(base) (*(volatile unsigned char *)((base) + 0x2c))
/*
- * linux/include/asm-arm/arch-realview/vmalloc.h
+ * arch/arm/mach-realview/include/mach/vmalloc.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Russell King.
#include <asm/hardware/arm_twd.h>
#include <asm/hardware/gic.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/smp.h>
#include <asm/cacheflush.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/board-eb.h>
-#include <asm/arch/board-pb11mp.h>
-#include <asm/arch/scu.h>
+#include <mach/board-eb.h>
+#include <mach/board-pb11mp.h>
+#include <mach/scu.h>
extern void realview_secondary_startup(void);
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
-#include <asm/arch/board-eb.h>
-#include <asm/arch/irqs.h>
+#include <mach/board-eb.h>
+#include <mach/irqs.h>
#include "core.h"
#include "clock.h"
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
-#include <asm/arch/board-pb1176.h>
-#include <asm/arch/irqs.h>
+#include <mach/board-pb1176.h>
+#include <mach/irqs.h>
#include "core.h"
#include "clock.h"
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
-#include <asm/arch/board-pb11mp.h>
-#include <asm/arch/irqs.h>
+#include <mach/board-pb11mp.h>
+#include <mach/irqs.h>
#include "core.h"
#include "clock.h"
#include <asm/fiq.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/uaccess.h>
#include <asm/mach/dma.h>
/*
- * linux/include/asm-arm/arch-rpc/acornfb.h
+ * arch/arm/mach-rpc/include/mach/acornfb.h
*
* Copyright (C) 1999 Russell King
*
-/* linux/include/asm-arm/arch-rpc/debug-macro.S
+/* arch/arm/mach-rpc/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-rpc/dma.h
+ * arch/arm/mach-rpc/include/mach/dma.h
*
* Copyright (C) 1997 Russell King
*
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/entry-macro-iomd.S>
.equ ioc_base_high, IOC_BASE & 0xff000000
/*
- * linux/include/asm-arm/arch-rpc/hardware.h
+ * arch/arm/mach-rpc/include/mach/hardware.h
*
* Copyright (C) 1996-1999 Russell King.
*
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
-#include <asm/arch/memory.h>
+#include <mach/memory.h>
#ifndef __ASSEMBLY__
#define IOMEM(x) ((void __iomem *)(unsigned long)(x))
/*
- * linux/include/asm-arm/arch-rpc/io.h
+ * arch/arm/mach-rpc/include/mach/io.h
*
* Copyright (C) 1997 Russell King
*
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-rpc/irqs.h
+ * arch/arm/mach-rpc/include/mach/irqs.h
*
* Copyright (C) 1996 Russell King
*
/*
- * linux/include/asm-arm/arch-rpc/memory.h
+ * arch/arm/mach-rpc/include/mach/memory.h
*
* Copyright (C) 1996,1997,1998 Russell King.
*
/*
- * linux/include/asm-arm/arch-rpc/system.h
+ * arch/arm/mach-rpc/include/mach/system.h
*
* Copyright (C) 1996-1999 Russell King.
*
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iomd.h>
#include <asm/io.h>
/*
- * linux/include/asm-arm/arch-rpc/timex.h
+ * arch/arm/mach-rpc/include/mach/timex.h
*
* Copyright (C) 1997, 1998 Russell King
*
/*
- * linux/include/asm-arm/arch-rpc/uncompress.h
+ * arch/arm/mach-rpc/include/mach/uncompress.h
*
* Copyright (C) 1996 Russell King
*
*/
#define VIDMEM ((char *)SCREEN_START)
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/page.h>
/*
- * linux/include/asm-arm/arch-rpc/vmalloc.h
+ * arch/arm/mach-rpc/include/mach/vmalloc.h
*
* Copyright (C) 1997 Russell King
*
#include <asm/elf.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include <asm/domain.h>
#include <asm/setup.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
int s3c2400_gpio_getirq(unsigned int pin)
{
-/* linux/include/asm-arm/arch-s3c2400/map.h
+/* arch/arm/mach-s3c2400/include/mach/map.h
*
* Copyright 2003,2007 Simtec Electronics
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2400/memory.h
- * from linux/include/asm-arm/arch-rpc/memory.h
+/* arch/arm/mach-s3c2400/include/mach/memory.h
+ * from arch/arm/mach-rpc/include/mach/memory.h
*
* Copyright 2007 Simtec Electronics
* http://armlinux.simtec.co.uk/
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/map.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-irq.h>
+#include <mach/map.h>
+#include <mach/bast-map.h>
+#include <mach/bast-irq.h>
/* IDE ports */
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-irq.h>
+#include <mach/regs-irq.h>
+#include <mach/bast-map.h>
+#include <mach/bast-irq.h>
#include <asm/plat-s3c24xx/irq.h>
#include <asm/mach/map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/clock.h>
#include <linux/serial_core.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/dma.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-ac97.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-sdi.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-sdi.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <asm/plat-s3c24xx/regs-spi.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on,
unsigned int config)
#include <linux/string.h>
#include <linux/ctype.h>
#include <linux/leds.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/hardware.h>
-#include <asm/arch/h1940-latch.h>
+#include <mach/regs-gpio.h>
+#include <mach/hardware.h>
+#include <mach/h1940-latch.h>
#define DRV_NAME "h1940-bt"
-/* linux/include/asm-arm/arch-s3c2410/anubis-cpld.h
+/* arch/arm/mach-s3c2410/include/mach/anubis-cpld.h
*
* Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
-/* linux/include/asm-arm/arch-s3c2410/anubis-irq.h
+/* arch/arm/mach-s3c2410/include/mach/anubis-irq.h
*
* Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
-/* linux/include/asm-arm/arch-s3c2410/anubis-map.h
+/* arch/arm/mach-s3c2410/include/mach/anubis-map.h
*
* Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
-/* linux/include/asm-arm/arch-s3c2410/audio.h
+/* arch/arm/mach-s3c2410/include/mach/audio.h
*
* Copyright (c) 2004-2005 Simtec Electronics
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/bast-cpld.h
+/* arch/arm/mach-s3c2410/include/mach/bast-cpld.h
*
* Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/bast-irq.h
+/* arch/arm/mach-s3c2410/include/mach/bast-irq.h
*
* Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/bast-map.h
+/* arch/arm/mach-s3c2410/include/mach/bast-map.h
*
* Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/bast-pmu.h
+/* arch/arm/mach-s3c2410/include/mach/bast-pmu.h
*
* Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/debug-macro.S
+/* arch/arm/mach-s3c2410/include/mach/debug-macro.S
*
* Debugging macro include header
*
* published by the Free Software Foundation.
*/
-#include <asm/arch/map.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/map.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-serial.h>
#define S3C2410_UART1_OFF (0x4000)
-/* linux/include/asm-arm/arch-s3c2410/dma.h
+/* arch/arm/mach-s3c2410/include/mach/dma.h
*
* Copyright (C) 2003,2004,2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
#define __ASM_ARCH_DMA_H __FILE__
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* This is the maximum DMA address(physical address) that can be DMAd to.
/*
- * include/asm-arm/arch-s3c2410/entry-macro.S
+ * arch/arm/mach-s3c2410/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for S3C2410-based platforms
*
#define INTPND (0x10)
#define INTOFFSET (0x14)
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
.macro get_irqnr_preamble, base, tmp
-/* linux/include/asm-arm/arch-s3c2410/fb.h
+/* arch/arm/mach-s3c2410/include/mach/fb.h
*
* Copyright (c) 2004 Arnaud Patard <arnaud.patard@rtp-net.org>
*
#ifndef __ASM_ARM_FB_H
#define __ASM_ARM_FB_H
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-lcd.h>
struct s3c2410fb_hw {
unsigned long lcdcon1;
-/* linux/include/asm-arm/arch-s3c2410/gpio.h
+/* arch/arm/mach-s3c2410/include/mach/gpio.h
*
* Copyright (c) 2008 Simtec Electronics
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/h1940-latch.h
+/* arch/arm/mach-s3c2410/include/mach/h1940-latch.h
*
* Copyright (c) 2005 Simtec Electronics
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/h1940.h
+/* arch/arm/mach-s3c2410/include/mach/h1940.h
*
* Copyright 2006 Ben Dooks <ben-linux@fluff.org>
*
-/* linux/include/asm-arm/arch-s3c2410/hardware.h
+/* arch/arm/mach-s3c2410/include/mach/hardware.h
*
* Copyright (c) 2003 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
-#ifndef __ASM_HARDWARE_H
-#error "Do not include this directly, instead #include <asm/hardware.h>"
-#endif
-
#ifndef __ASSEMBLY__
/* external functions for GPIO support
#endif /* __ASSEMBLY__ */
#include <asm/sizes.h>
-#include <asm/arch/map.h>
+#include <mach/map.h>
/* machine specific hardware definitions should go after this */
-/* linux/include/asm-arm/arch-s3c2410/idle.h
+/* arch/arm/mach-s3c2410/include/mach/idle.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
/*
- * linux/include/asm-arm/arch-s3c2410/io.h
- * from linux/include/asm-arm/arch-rpc/io.h
+ * arch/arm/mach-s3c2410/include/mach/io.h
+ * from arch/arm/mach-rpc/include/mach/io.h
*
* Copyright (C) 1997 Russell King
* (C) 2003 Simtec Electronics
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
-/* linux/include/asm-arm/arch-s3c2410/irqs.h
+/* arch/arm/mach-s3c2410/include/mach/irqs.h
*
* Copyright (c) 2003-2005 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/leds-gpio.h
+/* arch/arm/mach-s3c2410/include/mach/leds-gpio.h
*
* Copyright (c) 2006 Simtec Electronics
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/map.h
+/* arch/arm/mach-s3c2410/include/mach/map.h
*
* Copyright (c) 2003 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/memory.h
- * from linux/include/asm-arm/arch-rpc/memory.h
+/* arch/arm/mach-s3c2410/include/mach/memory.h
+ * from arch/arm/mach-rpc/include/mach/memory.h
*
* Copyright (C) 1996,1997,1998 Russell King.
*
-/* linux/include/asm-arm/arch-s3c2410/osiris-cpld.h
+/* arch/arm/mach-s3c2410/include/mach/osiris-cpld.h
*
* Copyright 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
-/* linux/include/asm-arm/arch-s3c2410/osiris-map.h
+/* arch/arm/mach-s3c2410/include/mach/osiris-map.h
*
* (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
-/* linux/include/asm-arm/arch-s3c2410/otom-map.h
+/* arch/arm/mach-s3c2410/include/mach/otom-map.h
*
* (c) 2005 Guillaume GOURAT / NexVision
* guillaume.gourat@nexvision.fr
-/* linux/include/asm-arm/arch-s3c2410/regs-clock.h
+/* arch/arm/mach-s3c2410/include/mach/regs-clock.h
*
* Copyright (c) 2003,2004,2005,2006 Simtec Electronics <linux@simtec.co.uk>
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/regs-dsc.h
+/* arch/arm/mach-s3c2410/include/mach/regs-dsc.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-gpio.h
+/* arch/arm/mach-s3c2410/include/mach/regs-gpio.h
*
* Copyright (c) 2003,2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-gpioj.h
+/* arch/arm/mach-s3c2410/include/mach/regs-gpioj.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-irq.h
+/* arch/arm/mach-s3c2410/include/mach/regs-irq.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-lcd.h
+/* arch/arm/mach-s3c2410/include/mach/regs-lcd.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-mem.h
+/* arch/arm/mach-s3c2410/include/mach/regs-mem.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-power.h
+/* arch/arm/mach-s3c2410/include/mach/regs-power.h
*
* Copyright (c) 2003,2004,2005,2006 Simtec Electronics <linux@simtec.co.uk>
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/regs-s3c2412-mem.h
+/* arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h
*
* Copyright (c) 2008 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/regs-s3c2412.h
+/* arch/arm/mach-s3c2410/include/mach/regs-s3c2412.h
*
* Copyright 2007 Simtec Electronics
* http://armlinux.simtec.co.uk/
-/* linux/include/asm-arm/arch-s3c2410/regs-s3c2443-clock.h
+/* arch/arm/mach-s3c2410/include/mach/regs-s3c2443-clock.h
*
* Copyright (c) 2007 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/regs-sdi.h
+/* arch/arm/mach-s3c2410/include/mach/regs-sdi.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/reset.h
+/* arch/arm/mach-s3c2410/include/mach/reset.h
*
* Copyright (c) 2007 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/spi-gpio.h
+/* arch/arm/mach-s3c2410/include/mach/spi-gpio.h
*
* Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/spi.h
+/* arch/arm/mach-s3c2410/include/mach/spi.h
*
* Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/system-reset.h
+/* arch/arm/mach-s3c2410/include/mach/system-reset.h
*
* Copyright (c) 2008 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/plat-s3c/regs-watchdog.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <linux/clk.h>
#include <linux/err.h>
-/* linux/include/asm-arm/arch-s3c2410/system.h
+/* arch/arm/mach-s3c2410/include/mach/system.h
*
* Copyright (c) 2003 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
* published by the Free Software Foundation.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/map.h>
-#include <asm/arch/idle.h>
-#include <asm/arch/reset.h>
+#include <mach/map.h>
+#include <mach/idle.h>
+#include <mach/reset.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
void (*s3c24xx_idle)(void);
void (*s3c24xx_reset_hook)(void);
s3c24xx_default_idle();
}
-#include <asm/arch/system-reset.h>
+#include <mach/system-reset.h>
-/* linux/include/asm-arm/arch-s3c2410/timex.h
+/* arch/arm/mach-s3c2410/include/mach/timex.h
*
* Copyright (c) 2003-2005 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/uncompress.h
+/* arch/arm/mach-s3c2410/include/mach/uncompress.h
*
* Copyright (c) 2003, 2007 Simtec Electronics
* http://armlinux.simtec.co.uk/
#ifndef __ASM_ARCH_UNCOMPRESS_H
#define __ASM_ARCH_UNCOMPRESS_H
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/map.h>
+#include <mach/regs-gpio.h>
+#include <mach/map.h>
/* working in physical space... */
#undef S3C2410_GPIOREG
-/* linux/include/asm-arm/arch-s3c2410/usb-control.h
+/* arch/arm/mach-s3c2410/include/mach/usb-control.h
*
* Copyright (c) 2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*/
#ifndef __ASM_ARCH_USBCONTROL_H
-#define __ASM_ARCH_USBCONTROL_H "include/asm-arm/arch-s3c2410/usb-control.h"
+#define __ASM_ARCH_USBCONTROL_H "arch/arm/mach-s3c2410/include/mach/usb-control.h"
#define S3C_HCDFLG_USED (1)
-/* linux/include/asm-arm/arch-s3c2410/vmalloc.h
+/* arch/arm/mach-s3c2410/include/mach/vmalloc.h
*
- * from linux/include/asm-arm/arch-iop3xx/vmalloc.h
+ * from arch/arm/mach-iop3xx/include/mach/vmalloc.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/vr1000-cpld.h
+/* arch/arm/mach-s3c2410/include/mach/vr1000-cpld.h
*
* Copyright (c) 2003 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/vr1000-irq.h
+/* arch/arm/mach-s3c2410/include/mach/vr1000-irq.h
*
* Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/vr1000-map.h
+/* arch/arm/mach-s3c2410/include/mach/vr1000-map.h
*
* Copyright (c) 2003-2005 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
#ifndef __ASM_ARCH_VR1000MAP_H
#define __ASM_ARCH_VR1000MAP_H
-#include <asm/arch/bast-map.h>
+#include <mach/bast-map.h>
#define VR1000_IOADDR(x) BAST_IOADDR(x)
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/arch/fb.h>
+#include <mach/fb.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/devs.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-irq.h>
-#include <asm/arch/bast-cpld.h>
+#include <mach/bast-map.h>
+#include <mach/bast-irq.h>
+#include <mach/bast-cpld.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
//#include <asm/debug-ll.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
#include <asm/plat-s3c/nand.h>
#include <asm/plat-s3c/iic.h>
-#include <asm/arch/fb.h>
+#include <mach/fb.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-clock.h>
-#include <asm/arch/h1940.h>
-#include <asm/arch/h1940-latch.h>
-#include <asm/arch/fb.h>
+#include <mach/h1940.h>
+#include <mach/h1940-latch.h>
+#include <mach/fb.h>
#include <asm/plat-s3c24xx/udc.h>
#include <asm/plat-s3c24xx/clock.h>
#include <linux/serial_core.h>
#include <linux/timer.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/arch/fb.h>
-#include <asm/arch/leds-gpio.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/fb.h>
+#include <mach/leds-gpio.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/otom-map.h>
+#include <mach/otom-map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/leds-gpio.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/fb.h>
+#include <mach/fb.h>
#include <asm/plat-s3c/nand.h>
#include <asm/plat-s3c24xx/udc.h>
-#include <asm/arch/spi.h>
-#include <asm/arch/spi-gpio.h>
+#include <mach/spi.h>
+#include <mach/spi-gpio.h>
#include <asm/plat-s3c24xx/common-smdk.h>
#include <asm/plat-s3c24xx/devs.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/irq.h>
#include <asm/mach/flash.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/vr1000-map.h>
-#include <asm/arch/vr1000-irq.h>
-#include <asm/arch/vr1000-cpld.h>
+#include <mach/bast-map.h>
+#include <mach/vr1000-map.h>
+#include <mach/vr1000-irq.h>
+#include <mach/vr1000-cpld.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/leds-gpio.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/devs.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/map.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-cpld.h>
+#include <mach/map.h>
+#include <mach/bast-map.h>
+#include <mach/bast-cpld.h>
static void simtec_nor_vpp(struct map_info *map, int vpp)
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
-#include <asm/arch/map.h>
+#include <mach/hardware.h>
+#include <mach/map.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
.text
.global h1940_pm_return
#include <linux/time.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/h1940.h>
+#include <mach/regs-gpio.h>
+#include <mach/h1940.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c/regs-serial.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
-#include <asm/arch/map.h>
+#include <mach/hardware.h>
+#include <mach/map.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-mem.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-mem.h>
#include <asm/plat-s3c/regs-serial.h>
/* s3c2410_cpu_suspend
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/bast-map.h>
-#include <asm/arch/bast-irq.h>
-#include <asm/arch/usb-control.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/bast-map.h>
+#include <mach/bast-irq.h>
+#include <mach/usb-control.h>
+#include <mach/regs-gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/s3c2412.h>
#include <asm/plat-s3c24xx/clock.h>
#include <linux/serial_core.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <asm/io.h>
#include <asm/plat-s3c24xx/dma.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-ac97.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-sdi.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-sdi.h>
#include <asm/plat-s3c24xx/regs-s3c2412-iis.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <asm/plat-s3c24xx/regs-spi.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
int s3c2412_gpio_set_sleepcfg(unsigned int pin, unsigned int state)
{
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-power.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-power.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/irq.h>
#include <asm/plat-s3c/nand.h>
#include <asm/plat-s3c/iic.h>
-#include <asm/arch/regs-power.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/spi-gpio.h>
-#include <asm/arch/fb.h>
+#include <mach/regs-power.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/spi-gpio.h>
+#include <mach/fb.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iomd.h>
#include <asm/setup.h>
#include <asm/io.h>
//#include <asm/debug-ll.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
-#include <asm/arch/idle.h>
+#include <mach/idle.h>
#include <asm/plat-s3c24xx/udc.h>
-#include <asm/arch/fb.h>
+#include <mach/fb.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/s3c2412.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
-#include <asm/arch/idle.h>
-#include <asm/arch/fb.h>
+#include <mach/idle.h>
+#include <mach/fb.h>
#include <asm/plat-s3c/nand.h>
#include <linux/sysdev.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-power.h>
-#include <asm/arch/regs-gpioj.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-dsc.h>
+#include <mach/regs-power.h>
+#include <mach/regs-gpioj.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-dsc.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/proc-fns.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/reset.h>
-#include <asm/arch/idle.h>
+#include <mach/reset.h>
+#include <mach/idle.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-power.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-gpioj.h>
-#include <asm/arch/regs-dsc.h>
+#include <mach/regs-power.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-gpioj.h>
+#include <mach/regs-dsc.h>
#include <asm/plat-s3c24xx/regs-spi.h>
-#include <asm/arch/regs-s3c2412.h>
+#include <mach/regs-s3c2412.h>
#include <asm/plat-s3c24xx/s3c2412.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
-#include <asm/arch/map.h>
+#include <mach/hardware.h>
+#include <mach/map.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-irq.h>
.text
#include <linux/mutex.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/atomic.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <linux/serial_core.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <asm/plat-s3c24xx/dma.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-ac97.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-sdi.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-sdi.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <asm/plat-s3c24xx/regs-spi.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-dsc.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-dsc.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/s3c2440.h>
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/anubis-map.h>
-#include <asm/arch/anubis-irq.h>
-#include <asm/arch/anubis-cpld.h>
+#include <mach/anubis-map.h>
+#include <mach/anubis-irq.h>
+#include <mach/anubis-cpld.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
#include <asm/plat-s3c/nand.h>
#include <linux/mtd/mtd.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
#include <asm/plat-s3c/nand.h>
#include <linux/mtd/mtd.h>
#include <asm/mach/irq.h>
#include <asm/setup.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
//#include <asm/debug-ll.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-serial.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/osiris-map.h>
-#include <asm/arch/osiris-cpld.h>
+#include <mach/osiris-map.h>
+#include <mach/osiris-cpld.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
#include <asm/plat-s3c/nand.h>
#include <linux/mtd/mtd.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
-#include <asm/arch/h1940.h>
+#include <mach/h1940.h>
#include <asm/plat-s3c/nand.h>
-#include <asm/arch/fb.h>
+#include <mach/fb.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/devs.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
-#include <asm/arch/idle.h>
-#include <asm/arch/fb.h>
+#include <mach/idle.h>
+#include <mach/fb.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/s3c2440.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/mutex.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/atomic.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/mach/map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/regs-s3c2443-clock.h>
+#include <mach/regs-s3c2443-clock.h>
#include <asm/plat-s3c24xx/s3c2443.h>
#include <asm/plat-s3c24xx/clock.h>
#include <linux/serial_core.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <asm/io.h>
#include <asm/plat-s3c24xx/dma.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-ac97.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-sdi.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-sdi.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <asm/plat-s3c24xx/regs-spi.h>
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
-#include <asm/arch/idle.h>
-#include <asm/arch/fb.h>
+#include <mach/idle.h>
+#include <mach/fb.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/s3c2440.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-s3c2443-clock.h>
-#include <asm/arch/reset.h>
+#include <mach/regs-s3c2443-clock.h>
+#include <mach/reset.h>
#include <asm/plat-s3c24xx/s3c2443.h>
#include <asm/plat-s3c24xx/devs.h>
# LEDs support
obj-$(CONFIG_LEDS) += $(led-y)
-# SA1110 USB client support
-#obj-$(CONFIG_SA1100_USB) += usb/
-
# Miscelaneous functions
obj-$(CONFIG_PM) += pm.o sleep.o
obj-$(CONFIG_SA1100_SSP) += ssp.o
#include <linux/delay.h>
#include <linux/mm.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach/irda.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/assabet.h>
-#include <asm/arch/mcp.h>
+#include <mach/assabet.h>
+#include <mach/mcp.h>
#include "generic.h"
#include <linux/mtd/partitions.h>
#include <linux/errno.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/hardware/sa1111.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/badge4.h>
+#include <mach/badge4.h>
#include "generic.h"
#include <linux/mtd/partitions.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/cerf.h>
-#include <asm/arch/mcp.h>
+#include <mach/cerf.h>
+#include <mach/mcp.h>
#include "generic.h"
static struct resource cerfuart2_resources[] = {
#include <linux/spinlock.h>
#include <linux/mutex.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Very simple clock implementation - we only have one clock to
#include <linux/mtd/partitions.h>
#include <linux/timer.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/setup.h>
-#include <asm/arch/collie.h>
+#include <mach/collie.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/hardware/scoop.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/locomo.h>
-#include <asm/arch/mcp.h>
+#include <mach/mcp.h>
#include "generic.h"
#include <linux/platform_device.h>
#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/scoop.h>
#include <asm/dma.h>
-#include <asm/arch/collie.h>
+#include <mach/collie.h>
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/sharpsl_pm.h>
#include <linux/init.h>
#include <linux/cpufreq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "generic.h"
#include <linux/delay.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/system.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
* address of the hardware registers for that channel as the channel
* identifier. This identifier is written to the location pointed by
* @dma_regs. The list of possible values for @device are listed into
- * linux/include/asm-arm/arch-sa1100/dma.h as a dma_device_t enum.
+ * arch/arm/mach-sa1100/include/mach/dma.h as a dma_device_t enum.
*
* Note that reading from a port and writing to the same port are
* actually considered as two different streams requiring separate
#include <asm/div64.h>
#include <asm/cnt32_to_63.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/pgtable.h>
#include <asm/mach/map.h>
#include "generic.h"
+unsigned int reset_status;
+EXPORT_SYMBOL(reset_status);
+
#define NR_FREQS 16
/*
#include <linux/module.h>
#include <asm/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "generic.h"
static int sa1100_gpio_get(struct gpio_chip *chip, unsigned offset)
#include <linux/serial_core.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/h3600.h>
+#include <mach/h3600.h>
#if defined (CONFIG_SA1100_H3600) || defined (CONFIG_SA1100_H3100)
-#include <asm/arch/h3600_gpio.h>
+#include <mach/h3600_gpio.h>
#endif
#ifdef CONFIG_SA1100_H3800
-#include <asm/arch/h3600_asic.h>
+#include <mach/h3600_asic.h>
#endif
#include "generic.h"
#define MAX_ASIC_ISR_LOOPS 20
-/* The order of these is important - see #include <asm/arch/irqs.h> */
+/* The order of these is important - see #include <mach/irqs.h> */
static u32 kpio_irq_mask[] = {
KPIO_KEY_ALL,
KPIO_SPI_INT,
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/page.h>
#define SA1101_p2v(PhAdd) (PhAdd)
#endif
-#include <asm/arch/bitfield.h>
+#include <mach/bitfield.h>
#define C 0
#define Assembly 1
/*
- * linux/include/asm-arm/arch-sa1100/assabet.h
+ * arch/arm/mach-sa1100/include/mach/assabet.h
*
* Created 2000/06/05 by Nicolas Pitre <nico@cam.org>
*
/*
- * linux/include/asm-arm/arch-sa1100/badge4.h
+ * arch/arm/mach-sa1100/include/mach/badge4.h
*
* Tim Connors <connors@hpl.hp.com>
* Christopher Hoover <ch@hpl.hp.com>
*/
#ifndef __ASM_ARCH_HARDWARE_H
-#error "include <asm/hardware.h> instead"
+#error "include <mach/hardware.h> instead"
#endif
#define BADGE4_SA1111_BASE (0x48000000)
/*
- * include/asm-arm/arch-sa1100/cerf.h
+ * arch/arm/mach-sa1100/include/mach/cerf.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
/*
- * linux/include/asm-arm/arch-sa1100/collie.h
+ * arch/arm/mach-sa1100/include/mach/collie.h
*
* This file contains the hardware specific definitions for Assabet
* Only include this file from SA1100-specific files.
-/* linux/include/asm-arm/arch-sa1100/debug-macro.S
+/* arch/arm/mach-sa1100/include/mach/debug-macro.S
*
* Debugging macro include header
*
* published by the Free Software Foundation.
*
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
movne \rx, #0xf8000000 @ virtual address
@ We probe for the active serial port here, coherently with
- @ the comment in include/asm-arm/arch-sa1100/uncompress.h.
+ @ the comment in arch/arm/mach-sa1100/include/mach/uncompress.h.
@ We assume r1 can be clobbered.
@ see if Ser3 is active
/*
- * linux/include/asm-arm/arch-sa1100/dma.h
+ * arch/arm/mach-sa1100/include/mach/dma.h
*
* Generic SA1100 DMA support
*
/*
- * include/asm-arm/arch-sa1100/entry-macro.S
+ * arch/arm/mach-sa1100/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for SA1100-based platforms
*
/*
- * linux/include/asm-arm/arch-sa1100/gpio.h
+ * arch/arm/mach-sa1100/include/mach/gpio.h
*
* SA1100 GPIO wrappers for arch-neutral GPIO calls
*
#ifndef __ASM_ARCH_SA1100_GPIO_H
#define __ASM_ARCH_SA1100_GPIO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm-generic/gpio.h>
/*
- * linux/include/asm-arm/arch-sa1100/hardware.h
+ * arch/arm/mach-sa1100/include/mach/hardware.h
*
* Copyright (C) 1998 Nicolas Pitre <nico@cam.org>
*
/*
- * linux/include/asm-arm/arch-sa1100/ide.h
+ * arch/arm/mach-sa1100/include/mach/ide.h
*
* Copyright (c) 1998 Hugo Fiennes & Nicolas Pitre
*
*/
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#error "This code is broken and needs update to match with current ide support"
/*
- * linux/include/asm-arm/arch-sa1100/io.h
+ * arch/arm/mach-sa1100/include/mach/io.h
*
* Copyright (C) 1997-1999 Russell King
*
/*
- * linux/include/asm-arm/arch-sa1100/irqs.h
+ * arch/arm/mach-sa1100/include/mach/irqs.h
*
* Copyright (C) 1996 Russell King
* Copyright (C) 1998 Deborah Wallach (updates for SA1100/Brutus).
/*
- * include/asm-arm/arch-sa1100/jornada720.h
+ * arch/arm/mach-sa1100/include/mach/jornada720.h
*
* This file contains SSP/MCU communication definitions for HP Jornada 710/720/728
*
/*
- * linux/include/asm-arm/arch-sa1100/mcp.h
+ * arch/arm/mach-sa1100/include/mach/mcp.h
*
* Copyright (C) 2005 Russell King.
*
/*
- * linux/include/asm-arm/arch-sa1100/memory.h
+ * arch/arm/mach-sa1100/include/mach/memory.h
*
* Copyright (C) 1999-2000 Nicolas Pitre <nico@cam.org>
*/
/*
- * linux/include/asm-arm/arch-sa1100/neponset.h
+ * arch/arm/mach-sa1100/include/mach/neponset.h
*
* Created 2000/06/05 by Nicolas Pitre <nico@cam.org>
*
--- /dev/null
+#ifndef __ASM_ARCH_RESET_H
+#define __ASM_ARCH_RESET_H
+
+#include "hardware.h"
+
+#define RESET_STATUS_HARDWARE (1 << 0) /* Hardware Reset */
+#define RESET_STATUS_WATCHDOG (1 << 1) /* Watchdog Reset */
+#define RESET_STATUS_LOWPOWER (1 << 2) /* Exit from Low Power/Sleep */
+#define RESET_STATUS_GPIO (1 << 3) /* GPIO Reset */
+#define RESET_STATUS_ALL (0xf)
+
+extern unsigned int reset_status;
+static inline void clear_reset_status(unsigned int mask)
+{
+ RCSR = mask;
+}
+
+#endif /* __ASM_ARCH_RESET_H */
/*
- * linux/include/asm-arm/arch-sa1100/simpad.h
+ * arch/arm/mach-sa1100/include/mach/simpad.h
*
* based of assabet.h same as HUW_Webpanel
*
/*
- * linux/include/asm-arm/arch-sa1100/system.h
+ * arch/arm/mach-sa1100/include/mach/system.h
*
* Copyright (c) 1999 Nicolas Pitre <nico@cam.org>
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-sa1100/timex.h
+ * arch/arm/mach-sa1100/include/mach/timex.h
*
* SA1100 architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-sa1100/uncompress.h
+ * arch/arm/mach-sa1100/include/mach/uncompress.h
*
* (C) 1999 Nicolas Pitre <nico@cam.org>
*
--- /dev/null
+/*
+ * arch/arm/mach-sa1100/include/mach/vmalloc.h
+ */
+#define VMALLOC_END (0xe8000000)
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/irq.h>
#include "generic.h"
#include <linux/mtd/partitions.h>
#include <video/s1d13xxxfb.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/sa1111.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/sched.h>
#include <linux/slab.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/ssp.h>
-#include <asm/arch/jornada720.h>
+#include <mach/jornada720.h>
static DEFINE_SPINLOCK(jornada_ssp_lock);
static unsigned long jornada_ssp_flags;
#include <linux/kernel.h>
#include <linux/tty.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/mcp.h>
+#include <mach/mcp.h>
#include "generic.h"
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/assabet.h>
+#include <mach/assabet.h>
#include "leds.h"
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
*/
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
-#include <asm/arch/simpad.h>
+#include <mach/simpad.h>
#include "leds.h"
#include <linux/platform_device.h>
#include <linux/slab.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/assabet.h>
-#include <asm/arch/neponset.h>
+#include <mach/assabet.h>
+#include <mach/neponset.h>
#include <asm/hardware/sa1111.h>
#include <asm/sizes.h>
#include <linux/mtd/partitions.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include "generic.h"
#include <linux/errno.h>
#include <linux/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/memory.h>
#include <asm/system.h>
#include <asm/mach/time.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/mcp.h>
-#include <asm/arch/shannon.h>
+#include <mach/mcp.h>
+#include <mach/shannon.h>
#include "generic.h"
#include <linux/mtd/partitions.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/serial_sa1100.h>
-#include <asm/arch/mcp.h>
-#include <asm/arch/simpad.h>
+#include <mach/mcp.h>
+#include <mach/simpad.h>
#include <linux/serial_core.h>
#include <linux/ioport.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/ssp.h>
#define TIMEOUT 100000
#include <linux/clockchips.h>
#include <asm/mach/time.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define MIN_OSCR_DELTA 2
-/* linux/include/asm-arm/arch-shark/debug-macro.S
+/* arch/arm/mach-shark/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-shark/dma.h
+ * arch/arm/mach-shark/include/mach/dma.h
*
* by Alexander Schulz
*/
/*
- * include/asm-arm/arch-shark/entry-macro.S
+ * arch/arm/mach-shark/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Shark platform
*
/*
- * linux/include/asm-arm/arch-shark/hardware.h
+ * arch/arm/mach-shark/include/mach/hardware.h
*
* by Alexander Schulz
*
* derived from:
- * linux/include/asm-arm/arch-ebsa110/hardware.h
+ * arch/arm/mach-ebsa110/include/mach/hardware.h
* Copyright (C) 1996-1999 Russell King.
*/
#ifndef __ASM_ARCH_HARDWARE_H
/*
- * linux/include/asm-arm/arch-shark/io.h
+ * arch/arm/mach-shark/include/mach/io.h
*
* by Alexander Schulz
*
* derived from:
- * linux/include/asm-arm/arch-ebsa110/io.h
+ * arch/arm/mach-ebsa110/include/mach/io.h
* Copyright (C) 1997,1998 Russell King
*/
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-shark/irqs.h
+ * arch/arm/mach-shark/include/mach/irqs.h
*
* by Alexander Schulz
*/
/*
- * linux/include/asm-arm/arch-shark/memory.h
+ * arch/arm/mach-shark/include/mach/memory.h
*
* by Alexander Schulz
*
* derived from:
- * linux/include/asm-arm/arch-ebsa110/memory.h
+ * arch/arm/mach-ebsa110/include/mach/memory.h
* Copyright (c) 1996-1999 Russell King.
*/
#ifndef __ASM_ARCH_MEMORY_H
/*
- * linux/include/asm-arm/arch-shark/system.h
+ * arch/arm/mach-shark/include/mach/system.h
*
* by Alexander Schulz
*/
/*
- * linux/include/asm-arm/arch-shark/timex.h
+ * arch/arm/mach-shark/include/mach/timex.h
*
* by Alexander Schulz
*/
/*
- * linux/include/asm-arm/arch-shark/uncompress.h
+ * arch/arm/mach-shark/include/mach/uncompress.h
* by Alexander Schulz
*
* derived from:
- * linux/include/asm-arm/arch-ebsa285/uncompress.h
+ * arch/arm/mach-footbridge/include/mach/uncompress.h
* Copyright (C) 1996,1997,1998 Russell King
*/
/*
- * linux/include/asm-arm/arch-shark/vmalloc.h
+ * arch/arm/mach-shark/include/mach/vmalloc.h
*/
#define VMALLOC_END (PAGE_OFFSET + 0x10000000)
* by Alexander Schulz
*
* derived from linux/arch/ppc/kernel/i8259.c and:
- * include/asm-arm/arch-ebsa110/irq.h
+ * arch/arm/mach-ebsa110/include/mach/irq.h
* Copyright (C) 1996-1998 Russell King
*/
#include <linux/spinlock.h>
#include <linux/ioport.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/cnt32_to_63.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/leds.h>
-/* linux/include/asm-arm/arch-versatile/debug-macro.S
+/* arch/arm/mach-versatile/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-versatile/dma.h
+ * arch/arm/mach-versatile/include/mach/dma.h
*
* Copyright (C) 2003 ARM Limited.
* Copyright (C) 1997,1998 Russell King
/*
- * include/asm-arm/arch-versatile/entry-macro.S
+ * arch/arm/mach-versatile/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for Versatile platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/vic.h>
.macro disable_fiq
/*
- * linux/include/asm-arm/arch-versatile/hardware.h
+ * arch/arm/mach-versatile/include/mach/hardware.h
*
* This file contains the hardware definitions of the Versatile boards.
*
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* PCI space virtual addresses
/*
- * linux/include/asm-arm/arch-versatile/io.h
+ * arch/arm/mach-versatile/include/mach/io.h
*
* Copyright (C) 2003 ARM Limited
*
/*
- * linux/include/asm-arm/arch-versatile/irqs.h
+ * arch/arm/mach-versatile/include/mach/irqs.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
/*
* IRQ interrupts definitions are the same as the INT definitions
/*
- * linux/include/asm-arm/arch-versatile/memory.h
+ * arch/arm/mach-versatile/include/mach/memory.h
*
* Copyright (C) 2003 ARM Limited
*
/*
- * linux/include/asm-arm/arch-versatile/platform.h
+ * arch/arm/mach-versatile/include/mach/platform.h
*
* Copyright (c) ARM Limited 2003. All rights reserved.
*
/*
- * linux/include/asm-arm/arch-versatile/system.h
+ * arch/arm/mach-versatile/include/mach/system.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
static inline void arch_idle(void)
{
/*
- * linux/include/asm-arm/arch-versatile/timex.h
+ * arch/arm/mach-versatile/include/mach/timex.h
*
* Versatile architecture timex specifications
*
/*
- * linux/include/asm-arm/arch-versatile/uncompress.h
+ * arch/arm/mach-versatile/include/mach/uncompress.h
*
* Copyright (C) 2003 ARM Limited
*
/*
- * linux/include/asm-arm/arch-versatile/vmalloc.h
+ * arch/arm/mach-versatile/include/mach/vmalloc.h
*
* Copyright (C) 2003 ARM Limited
* Copyright (C) 2000 Russell King.
#include <linux/spinlock.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || \
ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || \
ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || \
- ARCH_NS9XXX || ARCH_DAVINCI
+ ARCH_NS9XXX || ARCH_DAVINCI || ARCH_MX2
default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || \
ARCH_OMAP730 || ARCH_OMAP16XX || \
ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || \
select OUTER_CACHE
help
This option enables the L2x0 PrimeCell.
+
+config CACHE_XSC3L2
+ bool "Enable the L2 cache on XScale3"
+ depends on CPU_XSC3
+ default y
+ select OUTER_CACHE
+ help
+ This option enables the L2 cache on XScale3.
*/
#include <linux/linkage.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include "proc-macros.S"
*/
#include <linux/linkage.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include "proc-macros.S"
*/
#include <linux/linkage.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/page.h>
#include "proc-macros.S"
--- /dev/null
+/*
+ * arch/arm/mm/cache-xsc3l2.c - XScale3 L2 cache controller support
+ *
+ * Copyright (C) 2007 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#include <linux/init.h>
+#include <linux/spinlock.h>
+
+#include <asm/system.h>
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+
+#define CR_L2 (1 << 26)
+
+#define CACHE_LINE_SIZE 32
+#define CACHE_LINE_SHIFT 5
+#define CACHE_WAY_PER_SET 8
+
+#define CACHE_WAY_SIZE(l2ctype) (8192 << (((l2ctype) >> 8) & 0xf))
+#define CACHE_SET_SIZE(l2ctype) (CACHE_WAY_SIZE(l2ctype) >> CACHE_LINE_SHIFT)
+
+static inline int xsc3_l2_present(void)
+{
+ unsigned long l2ctype;
+
+ __asm__("mrc p15, 1, %0, c0, c0, 1" : "=r" (l2ctype));
+
+ return !!(l2ctype & 0xf8);
+}
+
+static inline void xsc3_l2_clean_mva(unsigned long addr)
+{
+ __asm__("mcr p15, 1, %0, c7, c11, 1" : : "r" (addr));
+}
+
+static inline void xsc3_l2_clean_pa(unsigned long addr)
+{
+ xsc3_l2_clean_mva(__phys_to_virt(addr));
+}
+
+static inline void xsc3_l2_inv_mva(unsigned long addr)
+{
+ __asm__("mcr p15, 1, %0, c7, c7, 1" : : "r" (addr));
+}
+
+static inline void xsc3_l2_inv_pa(unsigned long addr)
+{
+ xsc3_l2_inv_mva(__phys_to_virt(addr));
+}
+
+static inline void xsc3_l2_inv_all(void)
+{
+ unsigned long l2ctype, set_way;
+ int set, way;
+
+ __asm__("mrc p15, 1, %0, c0, c0, 1" : "=r" (l2ctype));
+
+ for (set = 0; set < CACHE_SET_SIZE(l2ctype); set++) {
+ for (way = 0; way < CACHE_WAY_PER_SET; way++) {
+ set_way = (way << 29) | (set << 5);
+ __asm__("mcr p15, 1, %0, c7, c11, 2" : : "r"(set_way));
+ }
+ }
+
+ dsb();
+}
+
+static void xsc3_l2_inv_range(unsigned long start, unsigned long end)
+{
+ if (start == 0 && end == -1ul) {
+ xsc3_l2_inv_all();
+ return;
+ }
+
+ /*
+ * Clean and invalidate partial first cache line.
+ */
+ if (start & (CACHE_LINE_SIZE - 1)) {
+ xsc3_l2_clean_pa(start & ~(CACHE_LINE_SIZE - 1));
+ xsc3_l2_inv_pa(start & ~(CACHE_LINE_SIZE - 1));
+ start = (start | (CACHE_LINE_SIZE - 1)) + 1;
+ }
+
+ /*
+ * Clean and invalidate partial last cache line.
+ */
+ if (end & (CACHE_LINE_SIZE - 1)) {
+ xsc3_l2_clean_pa(end & ~(CACHE_LINE_SIZE - 1));
+ xsc3_l2_inv_pa(end & ~(CACHE_LINE_SIZE - 1));
+ end &= ~(CACHE_LINE_SIZE - 1);
+ }
+
+ /*
+ * Invalidate all full cache lines between 'start' and 'end'.
+ */
+ while (start != end) {
+ xsc3_l2_inv_pa(start);
+ start += CACHE_LINE_SIZE;
+ }
+
+ dsb();
+}
+
+static void xsc3_l2_clean_range(unsigned long start, unsigned long end)
+{
+ start &= ~(CACHE_LINE_SIZE - 1);
+ while (start < end) {
+ xsc3_l2_clean_pa(start);
+ start += CACHE_LINE_SIZE;
+ }
+
+ dsb();
+}
+
+/*
+ * optimize L2 flush all operation by set/way format
+ */
+static inline void xsc3_l2_flush_all(void)
+{
+ unsigned long l2ctype, set_way;
+ int set, way;
+
+ __asm__("mrc p15, 1, %0, c0, c0, 1" : "=r" (l2ctype));
+
+ for (set = 0; set < CACHE_SET_SIZE(l2ctype); set++) {
+ for (way = 0; way < CACHE_WAY_PER_SET; way++) {
+ set_way = (way << 29) | (set << 5);
+ __asm__("mcr p15, 1, %0, c7, c15, 2" : : "r"(set_way));
+ }
+ }
+
+ dsb();
+}
+
+static void xsc3_l2_flush_range(unsigned long start, unsigned long end)
+{
+ if (start == 0 && end == -1ul) {
+ xsc3_l2_flush_all();
+ return;
+ }
+
+ start &= ~(CACHE_LINE_SIZE - 1);
+ while (start < end) {
+ xsc3_l2_clean_pa(start);
+ xsc3_l2_inv_pa(start);
+ start += CACHE_LINE_SIZE;
+ }
+
+ dsb();
+}
+
+static int __init xsc3_l2_init(void)
+{
+ if (!cpu_is_xsc3() || !xsc3_l2_present())
+ return 0;
+
+ if (!(get_cr() & CR_L2)) {
+ pr_info("XScale3 L2 cache enabled.\n");
+ adjust_cr(CR_L2, CR_L2);
+ xsc3_l2_inv_all();
+ }
+
+ outer_cache.inv_range = xsc3_l2_inv_range;
+ outer_cache.clean_range = xsc3_l2_clean_range;
+ outer_cache.flush_range = xsc3_l2_flush_range;
+
+ return 0;
+}
+core_initcall(xsc3_l2_init);
}
if (initrd_node == -1) {
- printk(KERN_ERR "initrd (0x%08lx - 0x%08lx) extends beyond "
+ printk(KERN_ERR "INITRD: 0x%08lx+0x%08lx extends beyond "
"physical memory - disabling initrd\n",
- phys_initrd_start, end);
+ phys_initrd_start, phys_initrd_size);
phys_initrd_start = phys_initrd_size = 0;
}
#endif
reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT,
boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT);
+ /*
+ * Reserve any special node zero regions.
+ */
+ if (node == 0)
+ reserve_node_zero(pgdat);
+
#ifdef CONFIG_BLK_DEV_INITRD
/*
* If the initrd is in this node, reserve its memory.
*/
if (node == initrd_node) {
- reserve_bootmem_node(pgdat, phys_initrd_start,
- phys_initrd_size, BOOTMEM_DEFAULT);
- initrd_start = __phys_to_virt(phys_initrd_start);
- initrd_end = initrd_start + phys_initrd_size;
+ int res = reserve_bootmem_node(pgdat, phys_initrd_start,
+ phys_initrd_size, BOOTMEM_EXCLUSIVE);
+
+ if (res == 0) {
+ initrd_start = __phys_to_virt(phys_initrd_start);
+ initrd_end = initrd_start + phys_initrd_size;
+ } else {
+ printk(KERN_ERR
+ "INITRD: 0x%08lx+0x%08lx overlaps in-use "
+ "memory region - disabling initrd\n",
+ phys_initrd_start, phys_initrd_size);
+ }
}
#endif
- /*
- * Finally, reserve any node zero regions.
- */
- if (node == 0)
- reserve_node_zero(pgdat);
-
/*
* initialise the zones within this node.
*/
* caller shouldn't need to know that small detail.
*
* 'flags' are the extra L_PTE_ flags that you want to specify for this
- * mapping. See include/asm-arm/proc-armv/pgtable.h for more information.
+ * mapping. See <asm/pgtable.h> for more information.
*/
void __iomem *
__arm_ioremap_pfn(unsigned long pfn, unsigned long offset, size_t size,
.align
/*
- * See linux/include/asm-arm/procinfo.h for a definition of this structure.
+ * See <asm/procinfo.h> for a definition of this structure.
*/
.section ".proc.info.init", #alloc, #execinstr
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
#include <asm/elf.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable-hwdef.h>
#include <asm/pgtable.h>
#include <asm/ptrace.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
#include <asm/elf.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable-hwdef.h>
#include <asm/pgtable.h>
#include <linux/init.h>
#include <asm/assembler.h>
#include <asm/elf.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/pgtable.h>
#include <asm/pgtable-hwdef.h>
#include <asm/page.h>
*/
#define CACHESIZE 32768
-/*
- * Run with L2 enabled.
- */
-#define L2_CACHE_ENABLE 1
-
/*
* This macro is used to wait for a CP15 write and is needed when we
* have to ensure that the last operation to the coprocessor was
tst r0, #CACHELINESIZE - 1
bic r0, r0, #CACHELINESIZE - 1
mcrne p15, 0, r0, c7, c10, 1 @ clean L1 D line
- mcrne p15, 1, r0, c7, c11, 1 @ clean L2 line
tst r1, #CACHELINESIZE - 1
mcrne p15, 0, r1, c7, c10, 1 @ clean L1 D line
- mcrne p15, 1, r1, c7, c11, 1 @ clean L2 line
1: mcr p15, 0, r0, c7, c6, 1 @ invalidate L1 D line
- mcr p15, 1, r0, c7, c7, 1 @ invalidate L2 line
add r0, r0, #CACHELINESIZE
cmp r0, r1
blo 1b
ENTRY(xsc3_dma_clean_range)
bic r0, r0, #CACHELINESIZE - 1
1: mcr p15, 0, r0, c7, c10, 1 @ clean L1 D line
- mcr p15, 1, r0, c7, c11, 1 @ clean L2 line
add r0, r0, #CACHELINESIZE
cmp r0, r1
blo 1b
ENTRY(xsc3_dma_flush_range)
bic r0, r0, #CACHELINESIZE - 1
1: mcr p15, 0, r0, c7, c14, 1 @ clean/invalidate L1 D line
- mcr p15, 1, r0, c7, c11, 1 @ clean L2 line
- mcr p15, 1, r0, c7, c7, 1 @ invalidate L2 line
add r0, r0, #CACHELINESIZE
cmp r0, r1
blo 1b
mcr p15, 0, ip, c7, c5, 0 @ invalidate L1 I cache and BTB
mcr p15, 0, ip, c7, c10, 4 @ data write barrier
mcr p15, 0, ip, c7, c5, 4 @ prefetch flush
-#ifdef L2_CACHE_ENABLE
orr r0, r0, #0x18 @ cache the page table in L2
-#endif
mcr p15, 0, r0, c2, c0, 0 @ load page table pointer
mcr p15, 0, ip, c8, c7, 0 @ invalidate I and D TLBs
cpwait_ret lr, ip
orreq r2, r2, #PTE_EXT_AP_UNO_SRW @ yes -> user n/a, system r/w
@ combined with user -> user r/w
-#if L2_CACHE_ENABLE
@ If it's cacheable, it needs to be in L2 also.
eor ip, r1, #L_PTE_CACHEABLE
tst ip, #L_PTE_CACHEABLE
orreq r2, r2, #PTE_EXT_TEX(0x5)
-#endif
tst r3, #L_PTE_PRESENT | L_PTE_YOUNG @ present and young?
movne r2, #0 @ no -> fault
mcr p15, 0, ip, c7, c10, 4 @ data write barrier
mcr p15, 0, ip, c7, c5, 4 @ prefetch flush
mcr p15, 0, ip, c8, c7, 0 @ invalidate I and D TLBs
-#if L2_CACHE_ENABLE
orr r4, r4, #0x18 @ cache the page table in L2
-#endif
mcr p15, 0, r4, c2, c0, 0 @ load page table pointer
mov r0, #0 @ don't allow CP access
mrc p15, 0, r0, c1, c0, 1 @ get auxiliary control reg
and r0, r0, #2 @ preserve bit P bit setting
-#if L2_CACHE_ENABLE
orr r0, r0, #(1 << 10) @ enable L2 for LLR cache
-#endif
mcr p15, 0, r0, c1, c0, 1 @ set auxiliary control reg
adr r5, xsc3_crval
bic r0, r0, r5 @ ..V. ..R. .... ..A.
orr r0, r0, r6 @ ..VI Z..S .... .C.M (mmu)
@ ...I Z..S .... .... (uc)
-#if L2_CACHE_ENABLE
- orr r0, r0, #0x04000000 @ L2 enable
-#endif
mov pc, lr
.size __xsc3_setup, . - __xsc3_setup
* This structure is exported to user space. Do not re-order.
* Only add new stuff to the end, and do not change the size of
* any element. Elements of this structure are used by user
- * space, and must match struct user_fp in include/asm-arm/user.h.
+ * space, and must match struct user_fp in <asm/user.h>.
* We include the byte offsets below for documentation purposes.
*
* The size of this structure and FPREG are checked by fpmodule.c
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include "op_counter.h"
#include <linux/platform_device.h>
#include <asm/hardware/iop3xx.h>
#include <linux/dma-mapping.h>
-#include <asm/arch/adma.h>
+#include <mach/adma.h>
#include <asm/hardware/iop_adma.h>
#ifdef CONFIG_ARCH_IOP32X
#include <asm/setup.h>
#include <asm/system.h>
#include <asm/memory.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iop3xx.h>
-#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#ifdef CONFIG_ARCH_IOP32X
*/
#include <linux/kernel.h>
#include <linux/module.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
void * __iomem __iop3xx_ioremap(unsigned long cookie, size_t size,
#include <asm/irq.h>
#include <asm/signal.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/pci.h>
#include <asm/hardware/iop3xx.h>
-#include <asm/mach-types.h>
// #define DEBUG
#include <linux/time.h>
#include <linux/init.h>
#include <linux/timex.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include <asm/arch/time.h>
+#include <mach/time.h>
static unsigned long ticks_per_jiffy;
static unsigned long ticks_per_usec;
#include <linux/string.h>
#include <linux/version.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
static LIST_HEAD(clocks);
static DEFINE_MUTEX(clocks_mutex);
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm-generic/bug.h>
static struct mxc_gpio_port *mxc_gpio_ports;
-/* linux/include/asm-arm/arch-imx/debug-macro.S
+/* arch/arm/mach-imx/include/mach/debug-macro.S
*
* Debugging macro include header
*
*
*/
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#ifdef CONFIG_MACH_MX31ADS
-#include <asm/arch/board-mx31ads.h>
+#include <mach/board-mx31ads.h>
#endif
#ifdef CONFIG_MACH_PCM037
-#include <asm/arch/board-pcm037.h>
+#include <mach/board-pcm037.h>
#endif
#ifdef CONFIG_MACH_MX31LITE
-#include <asm/arch/board-mx31lite.h>
+#include <mach/board-mx31lite.h>
#endif
#ifdef CONFIG_MACH_MX27ADS
-#include <asm/arch/board-mx27ads.h>
+#include <mach/board-mx27ads.h>
#endif
#ifdef CONFIG_MACH_PCM038
-#include <asm/arch/board-pcm038.h>
+#include <mach/board-pcm038.h>
#endif
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
#ifndef __ASM_ARCH_MXC_GPIO_H__
#define __ASM_ARCH_MXC_GPIO_H__
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm-generic/gpio.h>
/* use gpiolib dispatchers */
#include <asm/sizes.h>
#ifdef CONFIG_ARCH_MX3
-# include <asm/arch/mx31.h>
+# include <mach/mx31.h>
#endif
#ifdef CONFIG_ARCH_MX2
# ifdef CONFIG_MACH_MX27
-# include <asm/arch/mx27.h>
+# include <mach/mx27.h>
# endif
#endif
-#include <asm/arch/mxc.h>
+#include <mach/mxc.h>
#endif /* __ASM_ARCH_MXC_HARDWARE_H__ */
#ifndef __ASM_ARCH_MXC_IRQS_H__
#define __ASM_ARCH_MXC_IRQS_H__
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#endif /* __ASM_ARCH_MXC_IRQS_H__ */
#ifndef __ASM_ARCH_MXC_MEMORY_H__
#define __ASM_ARCH_MXC_MEMORY_H__
-#include <asm/hardware.h>
+#include <mach/hardware.h>
/*
* Virtual view <-> DMA view memory address translations
#define __PLAT_MXC_TIMER_H
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#ifdef CONFIG_ARCH_IMX
#define TIMER_BASE IO_ADDRESS(TIM1_BASE_ADDR)
#ifndef __ASM_ARCH_MXC_TIMEX_H__
#define __ASM_ARCH_MXC_TIMEX_H__
-#include <asm/hardware.h> /* for CLOCK_TICK_RATE */
+#include <mach/hardware.h> /* for CLOCK_TICK_RATE */
#endif /* __ASM_ARCH_MXC_TIMEX_H__ */
/*
- * include/asm-arm/arch-mxc/uncompress.h
+ * arch/arm/plat-mxc/include/mach/uncompress.h
*
*
*
#define __MXC_BOOT_UNCOMPRESS
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define UART(x) (*(volatile unsigned long *)(serial_port + (x)))
#include <linux/string.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/map.h>
-#include <asm/arch/iomux-mx1-mx2.h>
+#include <mach/iomux-mx1-mx2.h>
void mxc_gpio_mode(int gpio_mode)
{
#include <linux/irq.h>
#include <asm/io.h>
-#include <asm/arch/common.h>
+#include <mach/common.h>
#define AVIC_BASE IO_ADDRESS(AVIC_BASE_ADDR)
#define AVIC_INTCNTL (AVIC_BASE + 0x00) /* int control reg */
#include <linux/clockchips.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/time.h>
-#include <asm/arch/common.h>
-#include <asm/arch/mxc_timer.h>
+#include <mach/common.h>
+#include <mach/mxc_timer.h>
static struct clock_event_device clockevent_mxc;
static enum clock_event_mode clockevent_mode = CLOCK_EVT_MODE_UNUSED;
#include <asm/io.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
static LIST_HEAD(clocks);
static DEFINE_MUTEX(clocks_mutex);
#include <linux/serial_reg.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/system.h>
#include <asm/pgtable.h>
#include <asm/mach/map.h>
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/arch/common.h>
-#include <asm/arch/board.h>
-#include <asm/arch/control.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
+#include <mach/common.h>
+#include <mach/board.h>
+#include <mach/control.h>
+#include <mach/mux.h>
+#include <mach/fpga.h>
-#include <asm/arch/clock.h>
+#include <mach/clock.h>
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
# include "../mach-omap2/sdrc.h"
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/system.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
/* Many OMAP development platforms reuse the same "debug board"; these
#include <linux/leds.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <asm/mach-types.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/gpio.h>
+#include <mach/fpga.h>
+#include <mach/gpio.h>
/* Many OMAP development platforms reuse the same "debug board"; these
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <asm/arch/tc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/menelaus.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/tc.h>
+#include <mach/board.h>
+#include <mach/mux.h>
+#include <mach/gpio.h>
+#include <mach/menelaus.h>
+#include <mach/mcbsp.h>
#if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE)
#include <linux/io.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
-#include <asm/arch/tc.h>
+#include <mach/tc.h>
#undef DEBUG
#include <linux/list.h>
#include <linux/clk.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
-#include <asm/arch/dmtimer.h>
+#include <mach/hardware.h>
+#include <mach/dmtimer.h>
#include <asm/io.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
/* register offsets */
#define _OMAP_TIMER_ID_OFFSET 0x00
#include <linux/platform_device.h>
#include <linux/bootmem.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
#include <asm/mach/map.h>
-#include <asm/arch/board.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/omapfb.h>
+#include <mach/board.h>
+#include <mach/sram.h>
+#include <mach/omapfb.h>
#if defined(CONFIG_FB_OMAP) || defined(CONFIG_FB_OMAP_MODULE)
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/gpio.h>
+#include <mach/irqs.h>
+#include <mach/gpio.h>
#include <asm/mach/irq.h>
#include <asm/io.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
-#include <asm/mach-types.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
#define OMAP_I2C_SIZE 0x3f
#define OMAP1_I2C_BASE 0xfffb3800
/*
- * linux/include/asm-arm/arch-omap/aic23.h
+ * arch/arm/plat-omap/include/mach/aic23.h
*
* Hardware definitions for TI TLV320AIC23 audio codec
*
/*
- * linux/include/asm-arm/arch-omap/board-2430sdp.h
+ * arch/arm/plat-omap/include/mach/board-2430sdp.h
*
* Hardware definitions for TI OMAP2430 SDP board.
*
/*
- * linux/include/asm-arm/arch-omap/board-ams-delta.h
+ * arch/arm/plat-omap/include/mach/board-ams-delta.h
*
* Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
*
/*
- * linux/include/asm-arm/arch-omap/board-apollon.h
+ * arch/arm/plat-omap/include/mach/board-apollon.h
*
* Hardware definitions for Samsung OMAP24XX Apollon board.
*
/*
- * linux/include/asm-arm/arch-omap/board-fsample.h
+ * arch/arm/plat-omap/include/mach/board-fsample.h
*
* Board-specific goodies for TI F-Sample.
*
#define __ASM_ARCH_OMAP_FSAMPLE_H
/* fsample is pretty close to p2-sample */
-#include <asm/arch/board-perseus2.h>
+#include <mach/board-perseus2.h>
#define fsample_cpld_read(reg) __raw_readb(reg)
#define fsample_cpld_write(val, reg) __raw_writeb(val, reg)
/*
- * linux/include/asm-arm/arch-omap/board-h2.h
+ * arch/arm/plat-omap/include/mach/board-h2.h
*
* Hardware definitions for TI OMAP1610 H2 board.
*
/*
- * linux/include/asm-arm/arch-omap/board-h3.h
+ * arch/arm/plat-omap/include/mach/board-h3.h
*
* Copyright (C) 2001 RidgeRun, Inc.
* Copyright (C) 2004 Texas Instruments, Inc.
/*
- * linux/include/asm-arm/arch-omap/board-h4.h
+ * arch/arm/plat-omap/include/mach/board-h4.h
*
* Hardware definitions for TI OMAP1610 H4 board.
*
/*
- * linux/include/asm-arm/arch-omap/board-innovator.h
+ * arch/arm/plat-omap/include/mach/board-innovator.h
*
* Copyright (C) 2001 RidgeRun, Inc.
*
/*
- * linux/include/asm-arm/arch-omap/board-nokia.h
+ * arch/arm/plat-omap/include/mach/board-nokia.h
*
* Information structures for Nokia-specific board config data
*
/*
- * linux/include/asm-arm/arch-omap/board-osk.h
+ * arch/arm/plat-omap/include/mach/board-osk.h
*
* Hardware definitions for TI OMAP5912 OSK board.
*
/*
- * linux/include/asm-arm/arch-omap/board-palmte.h
+ * arch/arm/plat-omap/include/mach/board-palmte.h
*
* Hardware definitions for the Palm Tungsten E device.
*
/*
- * linux/include/asm-arm/arch-omap/board-palmte.h
+ * arch/arm/plat-omap/include/mach/board-palmte.h
*
* Hardware definitions for the Palm Tungsten|T device.
*
/*
- * linux/include/asm-arm/arch-omap/board-palmz71.h
+ * arch/arm/plat-omap/include/mach/board-palmz71.h
*
* Hardware definitions for the Palm Zire71 device.
*
/*
- * linux/include/asm-arm/arch-omap/board-perseus2.h
+ * arch/arm/plat-omap/include/mach/board-perseus2.h
*
* Copyright 2003 by Texas Instruments Incorporated
* OMAP730 / Perseus2 support by Jean Pihet
#ifndef __ASM_ARCH_OMAP_PERSEUS2_H
#define __ASM_ARCH_OMAP_PERSEUS2_H
-#include <asm/arch/fpga.h>
+#include <mach/fpga.h>
#ifndef OMAP_SDRAM_DEVICE
#define OMAP_SDRAM_DEVICE D256M_1X16_4B
/*
- * linux/include/asm-arm/arch-omap/board.h
+ * arch/arm/plat-omap/include/mach/board.h
*
* Information structures for board-specific data
*
#include <linux/types.h>
-#include <asm/arch/gpio-switch.h>
+#include <mach/gpio-switch.h>
/* Different peripheral ids */
#define OMAP_TAG_CLOCK 0x4f01
void (*set_power)(struct omap_pwm_led_platform_data *self, int on_off);
};
-/* See include/asm-arm/arch-omap/gpio-switch.h for definitions */
+/* See arch/arm/plat-omap/include/mach/gpio-switch.h for definitions */
struct omap_gpio_switch_config {
char name[12];
u16 gpio;
};
-#include <asm-arm/arch-omap/board-nokia.h>
+#include <mach/board-nokia.h>
struct omap_board_config_entry {
u16 tag;
/*
- * linux/include/asm-arm/arch-omap/clock.h
+ * arch/arm/plat-omap/include/mach/clock.h
*
* Copyright (C) 2004 - 2005 Nokia corporation
* Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com>
/*
- * linux/include/asm-arm/arch-omap/common.h
+ * arch/arm/plat-omap/include/mach/common.h
*
* Header for code common to all OMAP machines.
*
#define __ASM_ARCH_CONTROL_H
/*
- * include/asm-arm/arch-omap/control.h
+ * arch/arm/plat-omap/include/mach/control.h
*
* OMAP2/3 System Control Module definitions
*
* the Free Software Foundation.
*/
-#include <asm/arch/io.h>
+#include <mach/io.h>
#define OMAP242X_CTRL_REGADDR(reg) \
(void __iomem *)IO_ADDRESS(OMAP242X_CTRL_BASE + (reg))
/*
- * linux/include/asm-arm/arch-omap/cpu.h
+ * arch/arm/plat-omap/include/mach/cpu.h
*
* OMAP cpu type detection
*
-/* linux/include/asm-arm/arch-omap/debug-macro.S
+/* arch/arm/plat-omap/include/mach/debug-macro.S
*
* Debugging macro include header
*
/*
- * linux/include/asm-arm/arch-omap/dma.h
+ * arch/arm/plat-omap/include/mach/dma.h
*
* Copyright (C) 2003 Nokia Corporation
* Author: Juha Yrjölä <juha.yrjola@nokia.com>
/*
- * linux/include/asm-arm/arch-omap/dmtimer.h
+ * arch/arm/plat-omap/include/mach/dmtimer.h
*
* OMAP Dual-Mode Timers
*
/*
- * linux/include/asm-arm/arch-omap2/eac.h
+ * arch/arm/plat-omap/include/mach2/eac.h
*
* Defines for Enhanced Audio Controller
*
#ifndef __ASM_ARM_ARCH_OMAP2_EAC_H
#define __ASM_ARM_ARCH_OMAP2_EAC_H
-#include <asm/arch/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/io.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <sound/core.h>
/*
- * include/asm-arm/arch-omap/entry-macro.S
+ * arch/arm/plat-omap/include/mach/entry-macro.S
*
* Low-level IRQ helper macros for OMAP-based platforms
*
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
-#include <asm/hardware.h>
-#include <asm/arch/io.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/io.h>
+#include <mach/irqs.h>
#if defined(CONFIG_ARCH_OMAP1)
#elif defined(CONFIG_ARCH_OMAP24XX)
-#include <asm/arch/omap24xx.h>
+#include <mach/omap24xx.h>
.macro disable_fiq
.endm
/*
- * linux/include/asm-arm/arch-omap/fpga.h
+ * arch/arm/plat-omap/include/mach/fpga.h
*
* Interrupt handler for OMAP-1510 FPGA
*
/*
- * linux/include/asm-arm/arch-omap/gpio.h
+ * arch/arm/plat-omap/include/mach/gpio.h
*
* OMAP GPIO handling defines and functions
*
#ifndef __ASM_ARCH_OMAP_GPIO_H
#define __ASM_ARCH_OMAP_GPIO_H
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
#include <asm/io.h>
#define OMAP_MPUIO_BASE (void __iomem *)0xfffb5000
/*
- * linux/include/asm-arm/arch-omap/gpioexpander.h
+ * arch/arm/plat-omap/include/mach/gpioexpander.h
*
*
* Copyright (C) 2004 Texas Instruments, Inc.
/*
- * linux/include/asm-arm/arch-omap/hardware.h
+ * arch/arm/plat-omap/include/mach/hardware.h
*
* Hardware definitions for TI OMAP processors and boards
*
#include <asm/sizes.h>
#ifndef __ASSEMBLER__
#include <asm/types.h>
-#include <asm/arch/cpu.h>
+#include <mach/cpu.h>
#endif
-#include <asm/arch/serial.h>
+#include <mach/serial.h>
/*
* ---------------------------------------------------------------------------
/*
- * linux/include/asm-arm/arch-omap/io.h
+ * arch/arm/plat-omap/include/mach/io.h
*
* IO definitions for TI OMAP processors and boards
*
- * Copied from linux/include/asm-arm/arch-sa1100/io.h
+ * Copied from arch/arm/mach-sa1100/include/mach/io.h
* Copyright (C) 1997-1999 Russell King
*
* This program is free software; you can redistribute it and/or modify it
#ifndef __ASM_ARM_ARCH_IO_H
#define __ASM_ARM_ARCH_IO_H
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define IO_SPACE_LIMIT 0xffffffff
/*
- * linux/include/asm-arm/arch-omap/irda.h
+ * arch/arm/plat-omap/include/mach/irda.h
*
* Copyright (C) 2005-2006 Komal Shah <komal_shah802003@yahoo.com>
*
/*
- * linux/include/asm-arm/arch-omap/irqs.h
+ * arch/arm/plat-omap/include/mach/irqs.h
*
* Copyright (C) Greg Lonnon 2001
* Updated for OMAP-1610 by Tony Lindgren <tony@atomide.com>
extern void omap_init_irq(void);
#endif
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#endif
/*
- * linux/include/asm-arm/arch-omap/keypad.h
+ * arch/arm/plat-omap/include/mach/keypad.h
*
* Copyright (C) 2006 Komal Shah <komal_shah802003@yahoo.com>
*
/*
- * linux/include/asm-arm/arch-omap/led.h
+ * arch/arm/plat-omap/include/mach/led.h
*
* Copyright (C) 2006 Samsung Electronics
* Kyungmin Park <kyungmin.park@samsung.com>
/*
- * linux/include/asm-arm/arch-omap/mcbsp.h
+ * arch/arm/plat-omap/include/mach/mcbsp.h
*
* Defines for Multi-Channel Buffered Serial Port
*
#include <linux/completion.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
-#include <asm/arch/clock.h>
+#include <mach/hardware.h>
+#include <mach/clock.h>
#define OMAP730_MCBSP1_BASE 0xfffb1000
#define OMAP730_MCBSP2_BASE 0xfffb1800
/*
- * linux/include/asm-arm/arch-omap/memory.h
+ * arch/arm/plat-omap/include/mach/memory.h
*
* Memory map for OMAP-1510 and 1610
*
* Copyright (C) 2000 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
*
- * This file was derived from linux/include/asm-arm/arch-intergrator/memory.h
+ * This file was derived from arch/arm/mach-intergrator/include/mach/memory.h
* Copyright (C) 1999 ARM Limited
*
* This program is free software; you can redistribute it and/or modify it
/*
- * linux/include/asm-arm/arch-omap/menelaus.h
+ * arch/arm/plat-omap/include/mach/menelaus.h
*
* Functions to access Menelaus power management chip
*/
#include <linux/device.h>
#include <linux/mmc/host.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#define OMAP_MMC_MAX_SLOTS 2
#ifndef __ARCH_OMAP_MTD_XIP_H__
#define __ARCH_OMAP_MTD_XIP_H__
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define OMAP_MPU_TIMER_BASE (0xfffec500)
#define OMAP_MPU_TIMER_OFFSET 0x100
/*
- * linux/include/asm-arm/arch-omap/mux.h
+ * arch/arm/plat-omap/include/mach/mux.h
*
* Table of the Omap register configurations for the FUNC_MUX and
* PULL_DWN combinations.
/*
- * include/asm-arm/arch-omap/nand.h
+ * arch/arm/plat-omap/include/mach/nand.h
*
* Copyright (C) 2006 Micron Technology Inc.
*
/*
- * linux/include/asm-arm/arch-omap/omap-alsa.h
+ * arch/arm/plat-omap/include/mach/omap-alsa.h
*
* Alsa Driver for AIC23 and TSC2101 codecs on OMAP platform boards.
*
#ifndef __OMAP_ALSA_H
#define __OMAP_ALSA_H
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <sound/core.h>
#include <sound/pcm.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/mcbsp.h>
#include <linux/platform_device.h>
#define DMA_BUF_SIZE (1024 * 8)
-/* linux/include/asm-arm/arch-omap/omap1510.h
+/* arch/arm/plat-omap/include/mach/omap1510.h
*
* Hardware definitions for TI OMAP1510 processor.
*
-/* linux/include/asm-arm/arch-omap/omap16xx.h
+/* arch/arm/plat-omap/include/mach/omap16xx.h
*
* Hardware definitions for TI OMAP1610/5912/1710 processors.
*
/*
- * include/asm-arm/arch-omap/omap24xx.h
+ * arch/arm/plat-omap/include/mach/omap24xx.h
*
* This file contains the processor specific definitions
* of the TI OMAP24XX.
/*
- * include/asm-arm/arch-omap/omap34xx.h
+ * arch/arm/plat-omap/include/mach/omap34xx.h
*
* This file contains the processor specific definitions of the TI OMAP34XX.
*
-/* linux/include/asm-arm/arch-omap/omap730.h
+/* arch/arm/plat-omap/include/mach/omap730.h
*
* Hardware definitions for TI OMAP730 processor.
*
/*
- * File: include/asm-arm/arch-omap/omapfb.h
+ * File: arch/arm/plat-omap/include/mach/omapfb.h
*
* Framebuffer driver for TI OMAP boards
*
#include <linux/fb.h>
#include <linux/mutex.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#define OMAP_LCDC_INV_VSYNC 0x0001
#define OMAP_LCDC_INV_HSYNC 0x0002
/*
- * include/asm-arm/arch-omap/onenand.h
+ * arch/arm/plat-omap/include/mach/onenand.h
*
* Copyright (C) 2006 Nokia Corporation
* Author: Juha Yrjola
/*
- * linux/include/asm-arm/arch-omap/param.h
+ * arch/arm/plat-omap/include/mach/param.h
*
*/
/*
- * linux/include/asm-arm/arch-omap/pm.h
+ * arch/arm/plat-omap/include/mach/pm.h
*
* Header file for OMAP Power Management Routines
*
/*
- * linux/include/asm-arm/arch-omap/prcm.h
+ * arch/arm/plat-omap/include/mach/prcm.h
*
* Access definations for use in OMAP24XX clock and power management
*
* published by the Free Software Foundation.
*/
-#include <asm/arch/io.h>
+#include <mach/io.h>
/* SDRC register offsets - read/write with sdrc_{read,write}_reg() */
/*
- * linux/include/asm-arm/arch-omap/serial.h
+ * arch/arm/plat-omap/include/mach/serial.h
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
/*
- * linux/include/asm-arm/arch-omap/sram.h
+ * arch/arm/plat-omap/include/mach/sram.h
*
* Interface for functions that need to be run in internal SRAM
*
/*
- * Copied from linux/include/asm-arm/arch-sa1100/system.h
+ * Copied from arch/arm/mach-sa1100/include/mach/system.h
* Copyright (c) 1999 Nicolas Pitre <nico@cam.org>
*/
#ifndef __ASM_ARCH_SYSTEM_H
#include <linux/clk.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#ifndef CONFIG_MACH_VOICEBLUE
#define voiceblue_reset() do {} while (0)
/*
- * linux/include/asm-arm/arch-omap/tc.h
+ * arch/arm/plat-omap/include/mach/tc.h
*
* OMAP Traffic Controller
*
/*
- * linux/include/asm-arm/arch-omap/timex.h
+ * arch/arm/plat-omap/include/mach/timex.h
*
* Copyright (C) 2000 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
/*
- * linux/include/asm-arm/arch-omap/uncompress.h
+ * arch/arm/plat-omap/include/mach/uncompress.h
*
* Serial port stubs for kernel decompress status messages
*
* Initially based on:
- * linux-2.4.15-rmk1-dsplinux1.6/include/asm-arm/arch-omap1510/uncompress.h
+ * linux-2.4.15-rmk1-dsplinux1.6/arch/arm/plat-omap/include/mach1510/uncompress.h
* Copyright (C) 2000 RidgeRun, Inc.
* Author: Greg Lonnon <glonnon@ridgerun.com>
*
#include <linux/types.h>
#include <linux/serial_reg.h>
-#include <asm/arch/serial.h>
+#include <mach/serial.h>
unsigned int system_rev;
#ifndef __ASM_ARCH_OMAP_USB_H
#define __ASM_ARCH_OMAP_USB_H
-#include <asm/arch/board.h>
+#include <mach/board.h>
/*-------------------------------------------------------------------------*/
/*
- * linux/include/asm-arm/arch-omap/vmalloc.h
+ * arch/arm/plat-omap/include/mach/vmalloc.h
*
* Copyright (C) 2000 Russell King.
*
#include <linux/err.h>
#include <linux/delay.h>
#include <asm/io.h>
-#include <asm/arch/mailbox.h>
+#include <mach/mailbox.h>
#include "mailbox.h"
static struct omap_mbox *mboxes;
#include <linux/delay.h>
#include <linux/io.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/dma.h>
+#include <mach/mcbsp.h>
static struct omap_mcbsp mcbsp[OMAP_MAX_MCBSP_COUNT];
#include <asm/system.h>
#include <asm/io.h>
#include <linux/spinlock.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
#ifdef CONFIG_OMAP_MUX
#include <linux/clk.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define OCPI_BASE 0xfffec320
#define OCPI_FAULT (OCPI_BASE + 0x00)
#include <asm/mach/map.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/board.h>
+#include <mach/sram.h>
+#include <mach/board.h>
-#include <asm/arch/control.h>
+#include <mach/control.h>
#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
# include "../mach-omap2/prm.h"
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/control.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/usb.h>
-#include <asm/arch/board.h>
+#include <mach/control.h>
+#include <mach/mux.h>
+#include <mach/usb.h>
+#include <mach/board.h>
#ifdef CONFIG_ARCH_OMAP1
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <asm/mach/time.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
/*
* Number of timer ticks per jiffy.
#include <linux/mutex.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/leds-gpio.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
#include <asm/plat-s3c/nand.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/delay.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/system-reset.h>
+#include <mach/system-reset.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-serial.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/arch/fb.h>
-#include <asm/hardware.h>
+#include <mach/fb.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/mach/dma.h>
-#include <asm/arch/map.h>
+#include <mach/map.h>
#include <asm/plat-s3c24xx/dma.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function)
{
#include <linux/io.h>
#include <linux/gpio.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
struct s3c24xx_gpio_chip {
struct gpio_chip chip;
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/map.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
+#include <mach/map.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
#include <asm/mach-types.h>
#include <linux/serial_core.h>
#include <asm/cacheflush.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-mem.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-irq.h>
#include <asm/mach/time.h>
#include <linux/err.h>
#include <linux/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <linux/mutex.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/atomic.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c24xx/clock.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <linux/ioport.h>
#include <linux/sysdev.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-irq.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/cpu.h>
#include <asm/plat-s3c24xx/pm.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-clock.h>
+#include <mach/regs-clock.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-gpioj.h>
-#include <asm/arch/regs-dsc.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-gpioj.h>
+#include <mach/regs-dsc.h>
#include <asm/plat-s3c24xx/s3c2410.h>
#include <asm/plat-s3c24xx/s3c2440.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
-#include <asm/arch/map.h>
+#include <mach/hardware.h>
+#include <mach/map.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-mem.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-mem.h>
#include <asm/plat-s3c/regs-serial.h>
/* CONFIG_DEBUG_RESUME is dangerous if your bootloader does not
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/map.h>
+#include <mach/map.h>
#include <asm/plat-s3c/regs-timer.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-irq.h>
#include <asm/mach/time.h>
#include <asm/plat-s3c24xx/clock.h>
include/asm-arm/mach-types.h: $(src)/gen-mach-types $(src)/mach-types
@echo ' Generating $@'
+ @mkdir -p $(dir $@)
$(Q)$(AWK) -f $^ > $@ || { rm -f $@; /bin/false; }
CHECKFLAGS += -D__avr32__ -D__BIG_ENDIAN
+machine-$(CONFIG_PLATFORM_AT32AP) := at32ap
+machdirs := $(patsubst %,arch/avr32/mach-%/, $(machine-y))
+
+KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%include,$(machdirs))
+
head-$(CONFIG_LOADER_U_BOOT) += arch/avr32/boot/u-boot/head.o
head-y += arch/avr32/kernel/head.o
-core-$(CONFIG_PLATFORM_AT32AP) += arch/avr32/mach-at32ap/
+core-y += $(machdirs)
core-$(CONFIG_BOARD_ATSTK1000) += arch/avr32/boards/atstk1000/
core-$(CONFIG_BOARD_ATNGW100) += arch/avr32/boards/atngw100/
core-$(CONFIG_LOADER_U_BOOT) += arch/avr32/boot/u-boot/
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-#include <asm/arch/smc.h>
+#include <mach/smc.h>
static struct smc_timing flash_timing __initdata = {
.ncs_read_setup = 0,
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/init.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
/* Oscillator frequencies. These are board-specific */
unsigned long at32_board_osc_rates[3] = {
#include <asm/setup.h>
#include <asm/atmel-mci.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/init.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
#include "atstk1000.h"
*/
#ifdef CONFIG_BOARD_ATSTK1006
#include <linux/mtd/partitions.h>
-#include <asm/arch/smc.h>
+#include <mach/smc.h>
static struct smc_timing nand_timing __initdata = {
.ncs_read_setup = 0,
#include <asm/setup.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/init.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
#include "atstk1000.h"
#include <asm/setup.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/init.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
#include "atstk1000.h"
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-#include <asm/arch/smc.h>
+#include <mach/smc.h>
static struct smc_timing flash_timing __initdata = {
.ncs_read_setup = 0,
#include <asm/setup.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/portmux.h>
#include "atstk1000.h"
#ifndef __ASM_AVR32_GPIO_H
#define __ASM_AVR32_GPIO_H
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#endif /* __ASM_AVR32_GPIO_H */
#include <asm/addrspace.h>
#include <asm/byteorder.h>
-#include <asm/arch/io.h>
+#include <mach/io.h>
/* virt_to_phys will only work when address is in P1 or P2 */
static __inline__ unsigned long virt_to_phys(volatile void *address)
#define NR_INTERNAL_IRQS 64
-#include <asm/arch/irq.h>
+#include <mach/irq.h>
#ifndef NR_IRQS
#define NR_IRQS (NR_INTERNAL_IRQS)
#include <asm/sysreg.h>
#include <asm/ocd.h>
-#include <asm/arch/pm.h>
+#include <mach/pm.h>
void (*pm_power_off)(void) = NULL;
EXPORT_SYMBOL(pm_power_off);
#include <asm/setup.h>
#include <asm/sysreg.h>
-#include <asm/arch/board.h>
-#include <asm/arch/init.h>
+#include <mach/board.h>
+#include <mach/init.h>
extern int root_mountflags;
#include <asm/sysreg.h>
-#include <asm/arch/pm.h>
+#include <mach/pm.h>
static cycle_t read_cycle_count(void)
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/board.h>
-#include <asm/arch/portmux.h>
-#include <asm/arch/sram.h>
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/portmux.h>
+#include <mach/sram.h>
#include <video/atmel_lcdc.h>
#include <linux/platform_device.h>
#include <asm/io.h>
-#include <asm/arch/smc.h>
+#include <mach/smc.h>
#include "hsmc.h"
--- /dev/null
+/*
+ * Pin definitions for AT32AP7000.
+ *
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARCH_AT32AP700X_H__
+#define __ASM_ARCH_AT32AP700X_H__
+
+#define GPIO_PERIPH_A 0
+#define GPIO_PERIPH_B 1
+
+/*
+ * Pin numbers identifying specific GPIO pins on the chip. They can
+ * also be converted to IRQ numbers by passing them through
+ * gpio_to_irq().
+ */
+#define GPIO_PIOA_BASE (0)
+#define GPIO_PIOB_BASE (GPIO_PIOA_BASE + 32)
+#define GPIO_PIOC_BASE (GPIO_PIOB_BASE + 32)
+#define GPIO_PIOD_BASE (GPIO_PIOC_BASE + 32)
+#define GPIO_PIOE_BASE (GPIO_PIOD_BASE + 32)
+
+#define GPIO_PIN_PA(N) (GPIO_PIOA_BASE + (N))
+#define GPIO_PIN_PB(N) (GPIO_PIOB_BASE + (N))
+#define GPIO_PIN_PC(N) (GPIO_PIOC_BASE + (N))
+#define GPIO_PIN_PD(N) (GPIO_PIOD_BASE + (N))
+#define GPIO_PIN_PE(N) (GPIO_PIOE_BASE + (N))
+
+
+/*
+ * DMAC peripheral hardware handshaking interfaces, used with dw_dmac
+ */
+#define DMAC_MCI_RX 0
+#define DMAC_MCI_TX 1
+#define DMAC_DAC_TX 2
+#define DMAC_AC97_A_RX 3
+#define DMAC_AC97_A_TX 4
+#define DMAC_AC97_B_RX 5
+#define DMAC_AC97_B_TX 6
+#define DMAC_DMAREQ_0 7
+#define DMAC_DMAREQ_1 8
+#define DMAC_DMAREQ_2 9
+#define DMAC_DMAREQ_3 10
+
+#endif /* __ASM_ARCH_AT32AP700X_H__ */
--- /dev/null
+/*
+ * Platform data definitions.
+ */
+#ifndef __ASM_ARCH_BOARD_H
+#define __ASM_ARCH_BOARD_H
+
+#include <linux/types.h>
+
+#define GPIO_PIN_NONE (-1)
+
+/*
+ * Clock rates for various on-board oscillators. The number of entries
+ * in this array is chip-dependent.
+ */
+extern unsigned long at32_board_osc_rates[];
+
+/* Add basic devices: system manager, interrupt controller, portmuxes, etc. */
+void at32_add_system_devices(void);
+
+#define ATMEL_MAX_UART 4
+extern struct platform_device *atmel_default_console_device;
+
+struct atmel_uart_data {
+ short use_dma_tx; /* use transmit DMA? */
+ short use_dma_rx; /* use receive DMA? */
+ void __iomem *regs; /* virtual base address, if any */
+};
+void at32_map_usart(unsigned int hw_id, unsigned int line);
+struct platform_device *at32_add_device_usart(unsigned int id);
+
+struct eth_platform_data {
+ u32 phy_mask;
+ u8 is_rmii;
+};
+struct platform_device *
+at32_add_device_eth(unsigned int id, struct eth_platform_data *data);
+
+struct spi_board_info;
+struct platform_device *
+at32_add_device_spi(unsigned int id, struct spi_board_info *b, unsigned int n);
+
+struct atmel_lcdfb_info;
+struct platform_device *
+at32_add_device_lcdc(unsigned int id, struct atmel_lcdfb_info *data,
+ unsigned long fbmem_start, unsigned long fbmem_len,
+ unsigned int pin_config);
+
+struct usba_platform_data;
+struct platform_device *
+at32_add_device_usba(unsigned int id, struct usba_platform_data *data);
+
+struct ide_platform_data {
+ u8 cs;
+};
+struct platform_device *
+at32_add_device_ide(unsigned int id, unsigned int extint,
+ struct ide_platform_data *data);
+
+/* mask says which PWM channels to mux */
+struct platform_device *at32_add_device_pwm(u32 mask);
+
+/* depending on what's hooked up, not all SSC pins will be used */
+#define ATMEL_SSC_TK 0x01
+#define ATMEL_SSC_TF 0x02
+#define ATMEL_SSC_TD 0x04
+#define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
+
+#define ATMEL_SSC_RK 0x10
+#define ATMEL_SSC_RF 0x20
+#define ATMEL_SSC_RD 0x40
+#define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
+
+struct platform_device *
+at32_add_device_ssc(unsigned int id, unsigned int flags);
+
+struct i2c_board_info;
+struct platform_device *at32_add_device_twi(unsigned int id,
+ struct i2c_board_info *b,
+ unsigned int n);
+
+struct mci_platform_data;
+struct platform_device *
+at32_add_device_mci(unsigned int id, struct mci_platform_data *data);
+
+struct ac97c_platform_data {
+ unsigned short dma_rx_periph_id;
+ unsigned short dma_tx_periph_id;
+ unsigned short dma_controller_id;
+ int reset_pin;
+};
+struct platform_device *
+at32_add_device_ac97c(unsigned int id, struct ac97c_platform_data *data);
+
+struct platform_device *at32_add_device_abdac(unsigned int id);
+struct platform_device *at32_add_device_psif(unsigned int id);
+
+struct cf_platform_data {
+ int detect_pin;
+ int reset_pin;
+ int vcc_pin;
+ int ready_pin;
+ u8 cs;
+};
+struct platform_device *
+at32_add_device_cf(unsigned int id, unsigned int extint,
+ struct cf_platform_data *data);
+
+/* NAND / SmartMedia */
+struct atmel_nand_data {
+ int enable_pin; /* chip enable */
+ int det_pin; /* card detect */
+ int rdy_pin; /* ready/busy */
+ u8 ale; /* address line number connected to ALE */
+ u8 cle; /* address line number connected to CLE */
+ u8 bus_width_16; /* buswidth is 16 bit */
+ struct mtd_partition *(*partition_info)(int size, int *num_partitions);
+};
+struct platform_device *
+at32_add_device_nand(unsigned int id, struct atmel_nand_data *data);
+
+#endif /* __ASM_ARCH_BOARD_H */
--- /dev/null
+/*
+ * AVR32 and (fake) AT91 CPU identification
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARCH_CPU_H
+#define __ASM_ARCH_CPU_H
+
+/*
+ * Only AT32AP7000 is defined for now. We can identify the specific
+ * chip at runtime, but I'm not sure if it's really worth it.
+ */
+#ifdef CONFIG_CPU_AT32AP700X
+# define cpu_is_at32ap7000() (1)
+#else
+# define cpu_is_at32ap7000() (0)
+#endif
+
+/*
+ * Since this is AVR32, we will never run on any AT91 CPU. But these
+ * definitions may reduce clutter in common drivers.
+ */
+#define cpu_is_at91rm9200() (0)
+#define cpu_is_at91sam9xe() (0)
+#define cpu_is_at91sam9260() (0)
+#define cpu_is_at91sam9261() (0)
+#define cpu_is_at91sam9263() (0)
+#define cpu_is_at91sam9rl() (0)
+#define cpu_is_at91cap9() (0)
+
+#endif /* __ASM_ARCH_CPU_H */
--- /dev/null
+#ifndef __ASM_AVR32_ARCH_GPIO_H
+#define __ASM_AVR32_ARCH_GPIO_H
+
+#include <linux/compiler.h>
+#include <asm/irq.h>
+
+
+/* Some GPIO chips can manage IRQs; some can't. The exact numbers can
+ * be changed if needed, but for the moment they're not configurable.
+ */
+#define ARCH_NR_GPIOS (NR_GPIO_IRQS + 2 * 32)
+
+
+/* Arch-neutral GPIO API, supporting both "native" and external GPIOs. */
+#include <asm-generic/gpio.h>
+
+static inline int gpio_get_value(unsigned int gpio)
+{
+ return __gpio_get_value(gpio);
+}
+
+static inline void gpio_set_value(unsigned int gpio, int value)
+{
+ __gpio_set_value(gpio, value);
+}
+
+static inline int gpio_cansleep(unsigned int gpio)
+{
+ return __gpio_cansleep(gpio);
+}
+
+
+static inline int gpio_to_irq(unsigned int gpio)
+{
+ if (gpio < NR_GPIO_IRQS)
+ return gpio + GPIO_IRQ_BASE;
+ return -EINVAL;
+}
+
+static inline int irq_to_gpio(unsigned int irq)
+{
+ return irq - GPIO_IRQ_BASE;
+}
+
+#endif /* __ASM_AVR32_ARCH_GPIO_H */
--- /dev/null
+/*
+ * AT32AP platform initialization calls.
+ *
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_AVR32_AT32AP_INIT_H__
+#define __ASM_AVR32_AT32AP_INIT_H__
+
+void setup_platform(void);
+void setup_board(void);
+
+void at32_setup_serial_console(unsigned int usart_id);
+
+#endif /* __ASM_AVR32_AT32AP_INIT_H__ */
--- /dev/null
+#ifndef __ASM_AVR32_ARCH_AT32AP_IO_H
+#define __ASM_AVR32_ARCH_AT32AP_IO_H
+
+/* For "bizarre" halfword swapping */
+#include <linux/byteorder/swabb.h>
+
+#if defined(CONFIG_AP700X_32_BIT_SMC)
+# define __swizzle_addr_b(addr) (addr ^ 3UL)
+# define __swizzle_addr_w(addr) (addr ^ 2UL)
+# define __swizzle_addr_l(addr) (addr)
+# define ioswabb(a, x) (x)
+# define ioswabw(a, x) (x)
+# define ioswabl(a, x) (x)
+# define __mem_ioswabb(a, x) (x)
+# define __mem_ioswabw(a, x) swab16(x)
+# define __mem_ioswabl(a, x) swab32(x)
+#elif defined(CONFIG_AP700X_16_BIT_SMC)
+# define __swizzle_addr_b(addr) (addr ^ 1UL)
+# define __swizzle_addr_w(addr) (addr)
+# define __swizzle_addr_l(addr) (addr)
+# define ioswabb(a, x) (x)
+# define ioswabw(a, x) (x)
+# define ioswabl(a, x) swahw32(x)
+# define __mem_ioswabb(a, x) (x)
+# define __mem_ioswabw(a, x) swab16(x)
+# define __mem_ioswabl(a, x) swahb32(x)
+#else
+# define __swizzle_addr_b(addr) (addr)
+# define __swizzle_addr_w(addr) (addr)
+# define __swizzle_addr_l(addr) (addr)
+# define ioswabb(a, x) (x)
+# define ioswabw(a, x) swab16(x)
+# define ioswabl(a, x) swab32(x)
+# define __mem_ioswabb(a, x) (x)
+# define __mem_ioswabw(a, x) (x)
+# define __mem_ioswabl(a, x) (x)
+#endif
+
+#endif /* __ASM_AVR32_ARCH_AT32AP_IO_H */
--- /dev/null
+#ifndef __ASM_AVR32_ARCH_IRQ_H
+#define __ASM_AVR32_ARCH_IRQ_H
+
+#define EIM_IRQ_BASE NR_INTERNAL_IRQS
+#define NR_EIM_IRQS 32
+#define AT32_EXTINT(n) (EIM_IRQ_BASE + (n))
+
+#define GPIO_IRQ_BASE (EIM_IRQ_BASE + NR_EIM_IRQS)
+#define NR_GPIO_CTLR (5 /*internal*/ + 1 /*external*/)
+#define NR_GPIO_IRQS (NR_GPIO_CTLR * 32)
+
+#define NR_IRQS (GPIO_IRQ_BASE + NR_GPIO_IRQS)
+
+#endif /* __ASM_AVR32_ARCH_IRQ_H */
--- /dev/null
+/*
+ * AVR32 AP Power Management.
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_AVR32_ARCH_PM_H
+#define __ASM_AVR32_ARCH_PM_H
+
+/* Possible arguments to the "sleep" instruction */
+#define CPU_SLEEP_IDLE 0
+#define CPU_SLEEP_FROZEN 1
+#define CPU_SLEEP_STANDBY 2
+#define CPU_SLEEP_STOP 3
+#define CPU_SLEEP_STATIC 5
+
+#ifndef __ASSEMBLY__
+extern void cpu_enter_idle(void);
+extern void cpu_enter_standby(unsigned long sdramc_base);
+
+extern bool disable_idle_sleep;
+
+static inline void cpu_disable_idle_sleep(void)
+{
+ disable_idle_sleep = true;
+}
+
+static inline void cpu_enable_idle_sleep(void)
+{
+ disable_idle_sleep = false;
+}
+
+static inline void cpu_idle_sleep(void)
+{
+ /*
+ * If we're using the COUNT and COMPARE registers for
+ * timekeeping, we can't use the IDLE state.
+ */
+ if (disable_idle_sleep)
+ cpu_relax();
+ else
+ cpu_enter_idle();
+}
+
+void intc_set_suspend_handler(unsigned long offset);
+#endif
+
+#endif /* __ASM_AVR32_ARCH_PM_H */
--- /dev/null
+/*
+ * AT32 portmux interface.
+ *
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARCH_PORTMUX_H__
+#define __ASM_ARCH_PORTMUX_H__
+
+/*
+ * Set up pin multiplexing, called from board init only.
+ *
+ * The following flags determine the initial state of the pin.
+ */
+#define AT32_GPIOF_PULLUP 0x00000001 /* (not-OUT) Enable pull-up */
+#define AT32_GPIOF_OUTPUT 0x00000002 /* (OUT) Enable output driver */
+#define AT32_GPIOF_HIGH 0x00000004 /* (OUT) Set output high */
+#define AT32_GPIOF_DEGLITCH 0x00000008 /* (IN) Filter glitches */
+#define AT32_GPIOF_MULTIDRV 0x00000010 /* Enable multidriver option */
+
+void at32_select_periph(unsigned int pin, unsigned int periph,
+ unsigned long flags);
+void at32_select_gpio(unsigned int pin, unsigned long flags);
+void at32_reserve_pin(unsigned int pin);
+
+#endif /* __ASM_ARCH_PORTMUX_H__ */
--- /dev/null
+/*
+ * Static Memory Controller for AT32 chips
+ *
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * Inspired by the OMAP2 General-Purpose Memory Controller interface
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ARCH_AT32AP_SMC_H
+#define __ARCH_AT32AP_SMC_H
+
+/*
+ * All timing parameters are in nanoseconds.
+ */
+struct smc_timing {
+ /* Delay from address valid to assertion of given strobe */
+ int ncs_read_setup;
+ int nrd_setup;
+ int ncs_write_setup;
+ int nwe_setup;
+
+ /* Pulse length of given strobe */
+ int ncs_read_pulse;
+ int nrd_pulse;
+ int ncs_write_pulse;
+ int nwe_pulse;
+
+ /* Total cycle length of given operation */
+ int read_cycle;
+ int write_cycle;
+
+ /* Minimal recovery times, will extend cycle if needed */
+ int ncs_read_recover;
+ int nrd_recover;
+ int ncs_write_recover;
+ int nwe_recover;
+};
+
+/*
+ * All timing parameters are in clock cycles.
+ */
+struct smc_config {
+
+ /* Delay from address valid to assertion of given strobe */
+ u8 ncs_read_setup;
+ u8 nrd_setup;
+ u8 ncs_write_setup;
+ u8 nwe_setup;
+
+ /* Pulse length of given strobe */
+ u8 ncs_read_pulse;
+ u8 nrd_pulse;
+ u8 ncs_write_pulse;
+ u8 nwe_pulse;
+
+ /* Total cycle length of given operation */
+ u8 read_cycle;
+ u8 write_cycle;
+
+ /* Bus width in bytes */
+ u8 bus_width;
+
+ /*
+ * 0: Data is sampled on rising edge of NCS
+ * 1: Data is sampled on rising edge of NRD
+ */
+ unsigned int nrd_controlled:1;
+
+ /*
+ * 0: Data is driven on falling edge of NCS
+ * 1: Data is driven on falling edge of NWR
+ */
+ unsigned int nwe_controlled:1;
+
+ /*
+ * 0: NWAIT is disabled
+ * 1: Reserved
+ * 2: NWAIT is frozen mode
+ * 3: NWAIT in ready mode
+ */
+ unsigned int nwait_mode:2;
+
+ /*
+ * 0: Byte select access type
+ * 1: Byte write access type
+ */
+ unsigned int byte_write:1;
+
+ /*
+ * Number of clock cycles before data is released after
+ * the rising edge of the read controlling signal
+ *
+ * Total cycles from SMC is tdf_cycles + 1
+ */
+ unsigned int tdf_cycles:4;
+
+ /*
+ * 0: TDF optimization disabled
+ * 1: TDF optimization enabled
+ */
+ unsigned int tdf_mode:1;
+};
+
+extern void smc_set_timing(struct smc_config *config,
+ const struct smc_timing *timing);
+
+extern int smc_set_configuration(int cs, const struct smc_config *config);
+extern struct smc_config *smc_get_configuration(int cs);
+
+#endif /* __ARCH_AT32AP_SMC_H */
--- /dev/null
+/*
+ * Simple SRAM allocator
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_AVR32_ARCH_SRAM_H
+#define __ASM_AVR32_ARCH_SRAM_H
+
+#include <linux/genalloc.h>
+
+extern struct gen_pool *sram_pool;
+
+static inline unsigned long sram_alloc(size_t len)
+{
+ if (!sram_pool)
+ return 0UL;
+
+ return gen_pool_alloc(sram_pool, len);
+}
+
+static inline void sram_free(unsigned long addr, size_t len)
+{
+ return gen_pool_free(sram_pool, addr, len);
+}
+
+#endif /* __ASM_AVR32_ARCH_SRAM_H */
#include <asm/gpio.h>
#include <asm/io.h>
-#include <asm/arch/portmux.h>
+#include <mach/portmux.h>
#include "pio.h"
#include <asm/asm.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
-#include <asm/arch/pm.h>
+#include <mach/pm.h>
#include "pm.h"
#include "sdramc.h"
#include <asm/cacheflush.h>
#include <asm/sysreg.h>
-#include <asm/arch/pm.h>
-#include <asm/arch/sram.h>
+#include <mach/pm.h>
+#include <mach/sram.h>
/* FIXME: This is only valid for AP7000 */
#define SDRAMC_BASE 0xfff03800
.long sys_fallocate
.long sys_timerfd_settime /* 325 */
.long sys_timerfd_gettime
-
+ .long sys_signalfd4
+ .long sys_eventfd2
+ .long sys_epoll_create1
+ .long sys_dup3 /* 330 */
+ .long sys_pipe2
+ .long sys_inotify_init1
syscall_table_size = (. - sys_call_table)
to select this option. If in doubt, select ia64 generic support
instead.
-config IA64_SGI_UV`
- bool "SGI-UV`"
+config IA64_SGI_UV
+ bool "SGI-UV"
select NUMA
select ACPI_NUMA
select SWIOTLB
If you don't know what to do here, say N.
config NR_CPUS
- int "Maximum number of CPUs (2-1024)"
- range 2 1024
+ int "Maximum number of CPUs (2-4096)"
+ range 2 4096
depends on SMP
- default "1024"
+ default "4096"
help
You should set this to the number of CPUs in your system, but
keep in mind that a kernel compiled for, e.g., 2 CPUs will boot but
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22
-# Thu Jul 19 13:55:32 2007
+# Linux kernel version: 2.6.27-rc1
+# Mon Aug 4 15:38:01 2008
#
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=20
-# CONFIG_CPUSETS is not set
+CONFIG_CGROUPS=y
+# CONFIG_CGROUP_DEBUG is not set
+# CONFIG_CGROUP_NS is not set
+# CONFIG_CGROUP_DEVICE is not set
+CONFIG_CPUSETS=y
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUP_CPUACCT is not set
+# CONFIG_RESOURCE_COUNTERS is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_PROC_PID_CPUSET=y
# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_USE_GENERIC_SMP_HELPERS=y
+# CONFIG_HAVE_CLK is not set
+CONFIG_PROC_PAGE_MONITOR=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
CONFIG_BLOCK=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+CONFIG_BLOCK_COMPAT=y
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# Processor type and features
CONFIG_QUICKLIST=y
CONFIG_MMU=y
CONFIG_SWIOTLB=y
+CONFIG_IOMMU_HELPER=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_HAVE_SETUP_PER_CPU_AREA=y
CONFIG_DMI=y
CONFIG_EFI=y
CONFIG_GENERIC_IOMAP=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_IA64_UNCACHED_ALLOCATOR=y
CONFIG_AUDIT_ARCH=y
CONFIG_IA64_GENERIC=y
# CONFIG_IA64_DIG is not set
# CONFIG_IA64_HP_ZX1 is not set
# CONFIG_IA64_HP_ZX1_SWIOTLB is not set
# CONFIG_IA64_SGI_SN2 is not set
+# CONFIG_IA64_SGI_UV is not set
# CONFIG_IA64_HP_SIM is not set
# CONFIG_ITANIUM is not set
CONFIG_MCKINLEY=y
CONFIG_IA64_PAGE_SIZE_64KB=y
CONFIG_PGTABLE_3=y
# CONFIG_PGTABLE_4 is not set
+CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
-CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
CONFIG_IA64_L1_CACHE_SHIFT=7
CONFIG_IA64_CYCLONE=y
CONFIG_IOSAPIC=y
-# CONFIG_IA64_SGI_SN_XP is not set
CONFIG_FORCE_MAX_ZONEORDER=17
+# CONFIG_VIRT_CPU_ACCOUNTING is not set
CONFIG_SMP=y
-CONFIG_NR_CPUS=512
+CONFIG_NR_CPUS=4096
CONFIG_HOTPLUG_CPU=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
# CONFIG_SCHED_SMT is not set
# CONFIG_PERMIT_BSP_REMOVE is not set
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_NEED_MULTIPLE_NODES=y
# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
CONFIG_RESOURCES_64BIT=y
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
+CONFIG_MMU_NOTIFIER=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_HAVE_ARCH_NODEDATA_EXTENSION=y
CONFIG_IA32_SUPPORT=y
CONFIG_COMPAT=y
+CONFIG_COMPAT_FOR_U64_ALIGNMENT=y
CONFIG_IA64_MCA_RECOVERY=y
CONFIG_PERFMON=y
CONFIG_IA64_PALINFO=y
# CONFIG_IA64_MC_ERR_INJECT is not set
CONFIG_SGI_SN=y
# CONFIG_IA64_ESI is not set
+# CONFIG_IA64_HP_AML_NFW is not set
#
# SN Devices
#
# Firmware Drivers
#
+# CONFIG_FIRMWARE_MEMMAP is not set
CONFIG_EFI_VARS=y
CONFIG_EFI_PCDP=y
CONFIG_DMIID=y
# Power management and ACPI
#
CONFIG_PM=y
-CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
-
-#
-# ACPI (Advanced Configuration and Power Interface) Support
-#
CONFIG_ACPI=y
CONFIG_ACPI_PROCFS=y
+CONFIG_ACPI_PROCFS_POWER=y
+CONFIG_ACPI_SYSFS_POWER=y
+CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_BUTTON=m
CONFIG_ACPI_FAN=m
-# CONFIG_ACPI_DOCK is not set
+CONFIG_ACPI_DOCK=y
+# CONFIG_ACPI_BAY is not set
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=m
CONFIG_ACPI_NUMA=y
+# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
+# CONFIG_ACPI_PCI_SLOT is not set
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_ACPI_CONTAINER=m
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HOTPLUG_PCI=m
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set
# CONFIG_HOTPLUG_PCI_SGI is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
# CONFIG_PCCARD is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_LRO=m
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
CONFIG_SGI_IOC4=y
# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_SGI_XP=m
+# CONFIG_HP_ILO is not set
+CONFIG_SGI_GRU=m
+# CONFIG_SGI_GRU_DEBUG is not set
+CONFIG_HAVE_IDE=y
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=4
CONFIG_BLK_DEV_IDE=y
#
-# Please see Documentation/ide.txt for help/info on IDE drives
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_TIMINGS=y
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
+# CONFIG_BLK_DEV_PLATFORM is not set
# CONFIG_BLK_DEV_IDEPNP is not set
+CONFIG_BLK_DEV_IDEDMA_SFF=y
+
+#
+# PCI IDE chipsets support
+#
CONFIG_BLK_DEV_IDEPCI=y
-CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
-# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
CONFIG_BLK_DEV_CMD64X=y
# CONFIG_BLK_DEV_TRIFLEX is not set
-# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
-# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
-# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
-# CONFIG_IDEDMA_IVB is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
# CONFIG_SCSI_ISCSI_ATTRS is not set
CONFIG_SCSI_SAS_ATTRS=y
# CONFIG_SCSI_SAS_LIBSAS is not set
-
-#
-# SCSI low-level drivers
-#
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
CONFIG_SCSI_SYM53C8XX_MMIO=y
+# CONFIG_SCSI_IPR is not set
CONFIG_SCSI_QLOGIC_1280=y
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-# CONFIG_ATA is not set
+# CONFIG_SCSI_DH is not set
+CONFIG_ATA=y
+CONFIG_ATA_NONSTANDARD=y
+CONFIG_ATA_ACPI=y
+CONFIG_SATA_PMP=y
+# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
+# CONFIG_SATA_SVW is not set
+CONFIG_ATA_PIIX=y
+# CONFIG_SATA_MV is not set
+# CONFIG_SATA_NV is not set
+# CONFIG_PDC_ADMA is not set
+# CONFIG_SATA_QSTOR is not set
+# CONFIG_SATA_PROMISE is not set
+# CONFIG_SATA_SX4 is not set
+# CONFIG_SATA_SIL is not set
+# CONFIG_SATA_SIS is not set
+# CONFIG_SATA_ULI is not set
+# CONFIG_SATA_VIA is not set
+# CONFIG_SATA_VITESSE is not set
+# CONFIG_SATA_INIC162X is not set
+# CONFIG_PATA_ACPI is not set
+# CONFIG_PATA_ALI is not set
+# CONFIG_PATA_AMD is not set
+# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
+# CONFIG_PATA_CMD64X is not set
+# CONFIG_PATA_CS5520 is not set
+# CONFIG_PATA_CS5530 is not set
+# CONFIG_PATA_CYPRESS is not set
+# CONFIG_PATA_EFAR is not set
+# CONFIG_ATA_GENERIC is not set
+# CONFIG_PATA_HPT366 is not set
+# CONFIG_PATA_HPT37X is not set
+# CONFIG_PATA_HPT3X2N is not set
+# CONFIG_PATA_HPT3X3 is not set
+# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_IT8213 is not set
+# CONFIG_PATA_JMICRON is not set
+# CONFIG_PATA_TRIFLEX is not set
+# CONFIG_PATA_MARVELL is not set
+# CONFIG_PATA_MPIIX is not set
+# CONFIG_PATA_OLDPIIX is not set
+# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
+# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
+# CONFIG_PATA_OPTI is not set
+# CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RZ1000 is not set
+# CONFIG_PATA_SC1200 is not set
+# CONFIG_PATA_SERVERWORKS is not set
+# CONFIG_PATA_PDC2027X is not set
+# CONFIG_PATA_SIL680 is not set
+# CONFIG_PATA_SIS is not set
+# CONFIG_PATA_VIA is not set
+# CONFIG_PATA_WINBOND is not set
+# CONFIG_PATA_SCH is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_DM_MIRROR=m
CONFIG_DM_ZERO=m
CONFIG_DM_MULTIPATH=m
-# CONFIG_DM_MULTIPATH_EMC is not set
-# CONFIG_DM_MULTIPATH_RDAC is not set
# CONFIG_DM_DELAY is not set
-
-#
-# Fusion MPT device support
-#
+# CONFIG_DM_UEVENT is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=y
CONFIG_FUSION_FC=m
CONFIG_FUSION_SAS=y
CONFIG_FUSION_MAX_SGE=128
# CONFIG_FUSION_CTL is not set
+# CONFIG_FUSION_LOGGING is not set
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
-# CONFIG_PHYLIB is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
CONFIG_EEPRO100=m
CONFIG_E100=m
# CONFIG_FEALNX is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
+# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
+# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
-# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+CONFIG_IGB=y
+# CONFIG_IGB_LRO is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
+# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
-# CONFIG_MOXA_SMARTIO_NEW is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_SYNCLINK_GT is not set
# CONFIG_N_HDLC is not set
+# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
+# CONFIG_NOZOMI is not set
CONFIG_SGI_SNSC=y
CONFIG_SGI_TIOCX=y
CONFIG_SGI_MBCS=m
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_EFI_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-CONFIG_AGP=m
-CONFIG_AGP_I460=m
-CONFIG_AGP_HP_ZX1=m
-CONFIG_AGP_SGI_TIOCA=m
-CONFIG_DRM=m
-CONFIG_DRM_TDFX=m
-CONFIG_DRM_R128=m
-CONFIG_DRM_RADEON=m
-CONFIG_DRM_MGA=m
-CONFIG_DRM_SIS=m
-# CONFIG_DRM_VIA is not set
-# CONFIG_DRM_SAVAGE is not set
CONFIG_RAW_DRIVER=m
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
-# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set
CONFIG_MMTIMER=y
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
+CONFIG_POWER_SUPPLY=y
+# CONFIG_POWER_SUPPLY_DEBUG is not set
+# CONFIG_PDA_POWER is not set
+# CONFIG_BATTERY_DS2760 is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_THERMAL=m
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
CONFIG_DAB=y
# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
+CONFIG_AGP=m
+CONFIG_AGP_I460=m
+CONFIG_AGP_HP_ZX1=m
+CONFIG_AGP_SGI_TIOCA=m
+CONFIG_DRM=m
+CONFIG_DRM_TDFX=m
+CONFIG_DRM_R128=m
+CONFIG_DRM_RADEON=m
+CONFIG_DRM_MGA=m
+CONFIG_DRM_SIS=m
+# CONFIG_DRM_VIA is not set
+# CONFIG_DRM_SAVAGE is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_FB is not set
#
# Console display driver support
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_VERBOSE_PROCFS=y
CONFIG_SND_VERBOSE_PRINTK=y
# CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
+CONFIG_SND_VMASTER=y
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_MTPAV=m
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m
-
-#
-# PCI devices
-#
+# CONFIG_SND_AC97_POWER_SAVE is not set
+CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
+# CONFIG_SND_OXYGEN is not set
CONFIG_SND_CS4281=m
CONFIG_SND_CS46XX=m
CONFIG_SND_CS46XX_NEW_DSP=y
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
CONFIG_SND_FM801=m
-# CONFIG_SND_FM801_TEA575X_BOOL is not set
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
+# CONFIG_SND_HIFIER is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
+# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
-# CONFIG_SND_AC97_POWER_SAVE is not set
-
-#
-# USB devices
-#
+CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not set
-
-#
-# System on Chip audio support
-#
# CONFIG_SND_SOC is not set
-
-#
-# Open Sound System
-#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
#
# USB Input Devices
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
-# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=m
-# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
#
#
# USB port drivers
#
-
-#
-# USB Serial Converter support
-#
# CONFIG_USB_SERIAL is not set
#
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
-
-#
-# USB DSL modem support
-#
-
-#
-# USB Gadget Support
-#
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
+# CONFIG_ACCESSIBILITY is not set
CONFIG_INFINIBAND=m
# CONFIG_INFINIBAND_USER_MAD is not set
# CONFIG_INFINIBAND_USER_ACCESS is not set
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_MTHCA=m
CONFIG_INFINIBAND_MTHCA_DEBUG=y
+# CONFIG_INFINIBAND_IPATH is not set
# CONFIG_INFINIBAND_AMSO1100 is not set
# CONFIG_MLX4_INFINIBAND is not set
+# CONFIG_INFINIBAND_NES is not set
CONFIG_INFINIBAND_IPOIB=m
# CONFIG_INFINIBAND_IPOIB_CM is not set
CONFIG_INFINIBAND_IPOIB_DEBUG=y
# CONFIG_INFINIBAND_IPOIB_DEBUG_DATA is not set
# CONFIG_INFINIBAND_SRP is not set
# CONFIG_INFINIBAND_ISER is not set
-
-#
-# Real Time Clock
-#
# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
-# CONFIG_MSPEC is not set
+CONFIG_MSPEC=m
#
# File systems
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=y
# CONFIG_XFS_QUOTA is not set
-# CONFIG_XFS_SECURITY is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_XFS_RT is not set
+# CONFIG_XFS_DEBUG is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
-CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
+CONFIG_SUNRPC_XPRT_RDMA=m
+CONFIG_RPCSEC_GSS_KRB5=m
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
+CONFIG_HAVE_KVM=y
+CONFIG_VIRTUALIZATION=y
+# CONFIG_KVM is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC_T10DIF=y
+CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
+CONFIG_GENERIC_ALLOCATOR=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
# CONFIG_HP_SIMSERIAL is not set
# CONFIG_HP_SIMSCSI is not set
-#
-# Instrumentation Support
-#
-# CONFIG_PROFILING is not set
-# CONFIG_KPROBES is not set
-
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=2048
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
-CONFIG_FORCED_INLINING=y
+# CONFIG_DEBUG_SG is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
CONFIG_IA64_GRANULE_16MB=y
# CONFIG_IA64_GRANULE_64MB is not set
# CONFIG_IA64_PRINT_HAZARDS is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_MANAGER=m
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=m
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_PCBC=m
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=m
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+CONFIG_CRYPTO_DES=m
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
+# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
/*
- * asm-ia64/acpi.h
- *
* Copyright (C) 1999 VA Linux Systems
* Copyright (C) 1999 Walt Drummond <drummond@valinux.com>
* Copyright (C) 2000,2001 J.I. Lee <jung-ik.lee@intel.com>
/*
- * include/asm-ia64/cputime.h:
- * Definitions for measuring cputime on ia64 machines.
+ * Definitions for measuring cputime on ia64 machines.
*
* Based on <asm-powerpc/cputime.h>.
*
#ifndef _IA64_KDEBUG_H
#define _IA64_KDEBUG_H 1
/*
- * include/asm-ia64/kdebug.h
- *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
#define _ASM_KPROBES_H
/*
* Kernel Probes (KProbes)
- * include/asm-ia64/kprobes.h
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#define __ASM_IA64_KVM_H
/*
- * asm-ia64/kvm.h: kvm structure definitions for ia64
+ * kvm structure definitions for ia64
*
* Copyright (C) 2007 Xiantao Zhang <xiantao.zhang@intel.com>
*
#define __IA64_KVM_PARA_H
/*
- * asm-ia64/kvm_para.h
- *
* Copyright (C) 2007 Xiantao Zhang <xiantao.zhang@intel.com>
*
* This program is free software; you can redistribute it and/or modify it
extern void machvec_init_from_cmdline(const char *cmdline);
# else
-# error Unknown configuration. Update asm-ia64/machvec.h.
+# error Unknown configuration. Update arch/ia64/include/asm/machvec.h.
# endif /* CONFIG_IA64_GENERIC */
/*
/******************************************************************************
- * include/asm-ia64/native/inst.h
+ * arch/ia64/include/asm/native/inst.h
*
* Copyright (c) 2008 Isaku Yamahata <yamahata at valinux co jp>
* VA Linux Systems Japan K.K.
/******************************************************************************
- * include/asm-ia64/native/irq.h
+ * arch/ia64/include/asm/native/irq.h
*
* Copyright (c) 2008 Isaku Yamahata <yamahata at valinux co jp>
* VA Linux Systems Japan K.K.
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * moved from linux/include/asm-ia64/irq.h.
*/
#ifndef _ASM_IA64_NATIVE_IRQ_H
/******************************************************************************
- * include/asm-ia64/paravirt.h
- *
* Copyright (c) 2008 Isaku Yamahata <yamahata at valinux co jp>
* VA Linux Systems Japan K.K.
*
/******************************************************************************
- * include/asm-ia64/paravirt_privops.h
- *
* Copyright (c) 2008 Isaku Yamahata <yamahata at valinux co jp>
* VA Linux Systems Japan K.K.
*
/*
- * asm-ia64/rwsem.h: R/W semaphores for ia64
+ * R/W semaphores for ia64
*
* Copyright (C) 2003 Ken Chen <kenneth.w.chen@intel.com>
* Copyright (C) 2003 Asit Mallick <asit.k.mallick@intel.com>
/*
- * include/asm-ia64/serial.h
- *
* Derived from the i386 version.
*/
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
- * Copyright (c) 2001-2004 Silicon Graphics, Inc. All rights reserved.
+ * Copyright (c) 2001-2008 Silicon Graphics, Inc. All rights reserved.
*/
#ifndef _ASM_IA64_SN_MSPEC_H
#ifdef __KERNEL__
/*
- * Each Atomic Memory Operation (AMO formerly known as fetchop)
+ * Each Atomic Memory Operation (amo, formerly known as fetchop)
* variable is 64 bytes long. The first 8 bytes are used. The
* remaining 56 bytes are unaddressable due to the operation taking
* that portion of the address.
*
- * NOTE: The AMO_t _MUST_ be placed in either the first or second half
- * of the cache line. The cache line _MUST NOT_ be used for anything
- * other than additional AMO_t entries. This is because there are two
+ * NOTE: The amo structure _MUST_ be placed in either the first or second
+ * half of the cache line. The cache line _MUST NOT_ be used for anything
+ * other than additional amo entries. This is because there are two
* addresses which reference the same physical cache line. One will
* be a cached entry with the memory type bits all set. This address
- * may be loaded into processor cache. The AMO_t will be referenced
+ * may be loaded into processor cache. The amo will be referenced
* uncached via the memory special memory type. If any portion of the
* cached cache-line is modified, when that line is flushed, it will
* overwrite the uncached value in physical memory and lead to
* inconsistency.
*/
-typedef struct {
+struct amo {
u64 variable;
u64 unused[7];
-} AMO_t;
+};
#endif /* __KERNEL__ */
/*
* This is the access point to the Altix PROM hardware performance
* and status monitoring interface. For info on using this, see
- * include/asm-ia64/sn/sn2/sn_hwperf.h
+ * arch/ia64/include/asm/sn/sn2/sn_hwperf.h
*/
static inline int
ia64_sn_hwperf_op(nasid_t nasid, u64 opcode, u64 a0, u64 a1, u64 a2,
/*
- * linux/include/asm-ia64/topology.h
- *
* Copyright (C) 2002, Erich Focht, NEC
*
* All rights reserved.
/*
- * include/asm-ia64/xor.h
- *
* Optimized RAID-5 checksumming functions for IA-64.
*
* This program is free software; you can redistribute it and/or modify
#include <linux/pid.h>
#include <linux/clocksource.h>
#include <linux/kbuild.h>
-#include <asm-ia64/processor.h>
-#include <asm-ia64/ptrace.h>
-#include <asm-ia64/siginfo.h>
-#include <asm-ia64/sigcontext.h>
-#include <asm-ia64/mca.h>
+#include <asm/processor.h>
+#include <asm/ptrace.h>
+#include <asm/siginfo.h>
+#include <asm/sigcontext.h>
+#include <asm/mca.h>
#include "../kernel/sigframe.h"
#include "../kernel/fsyscall_gtod_data.h"
* p15 - used to track flag status.
*
* If you patch this code to use more registers, do not forget to update
- * the clobber lists for spin_lock() in include/asm-ia64/spinlock.h.
+ * the clobber lists for spin_lock() in arch/ia64/include/asm/spinlock.h.
*/
#if (__GNUC__ == 3 && __GNUC_MINOR__ < 3)
* systems, we use one-to-one mapping between IA-64 vector and IRQ. A
* platform can implement platform_irq_to_vector(irq) and
* platform_local_vector_to_irq(vector) APIs to differentiate the mapping.
- * Please see also include/asm-ia64/hw_irq.h for those APIs.
+ * Please see also arch/ia64/include/asm/hw_irq.h for those APIs.
*
* To sum up, there are three levels of mappings involved:
*
add r17=r17,r18 // now add the offset
;;
- MOV_FROM_IIP(r17)
+ MOV_TO_IIP(r17, r19)
dep r16=0,r16,41,2 // clear EI
;;
- MOV_FROM_IPSR(p0, r16)
+ MOV_TO_IPSR(p0, r16, r19)
;;
RFI
* to the correct location.
*/
#include <asm/asmmacro.h>
-#include <asm-ia64/break.h>
+#include <asm/break.h>
/*
* void jprobe_break(void)
#include <linux/kbuild.h>
#include <linux/threads.h>
-#include <asm-ia64/native/irq.h>
+#include <asm/native/irq.h>
void foo(void)
{
*
* Setup the reserved memory areas set aside for the boot parameters,
* initrd, etc. There are currently %IA64_MAX_RSVD_REGIONS defined,
- * see include/asm-ia64/meminit.h if you need to define more.
+ * see arch/ia64/include/asm/meminit.h if you need to define more.
*/
void __init
reserve_memory (void)
#include <linux/mm.h>
#include <linux/hugetlb.h>
#include <linux/pagemap.h>
+#include <linux/module.h>
#include <linux/slab.h>
#include <linux/sysctl.h>
#include <linux/log2.h>
#include <asm/tlb.h>
#include <asm/tlbflush.h>
-unsigned int hpage_shift=HPAGE_SHIFT_DEFAULT;
+unsigned int hpage_shift = HPAGE_SHIFT_DEFAULT;
+EXPORT_SYMBOL(hpage_shift);
pte_t *
huge_pte_alloc(struct mm_struct *mm, unsigned long addr, unsigned long sz)
/**
* __sn_mmiowb - I/O space memory barrier
*
- * See include/asm-ia64/io.h and Documentation/DocBook/deviceiobook.tmpl
+ * See arch/ia64/include/asm/io.h and Documentation/DocBook/deviceiobook.tmpl
* for details.
*
* On SN2, we wait for the PIO_WRITE_STATUS SHub register to clear.
#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/init.h>
-#include <linux/ide.h>
#include <asm/traps.h>
#include <asm/bootinfo.h>
#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/init.h>
-#include <linux/ide.h>
#include <linux/module.h>
#include <asm/bootinfo.h>
default y
select HAVE_IDE
select HAVE_OPROFILE
+ select HAVE_ARCH_KGDB
# Horrible source of confusion. Die, die, die ...
select EMBEDDED
select RTC_LIB
select SYS_HAS_CPU_RM9000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
help
The eXcite is a smart camera platform manufactured by
Basler Vision Technologies AG.
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select IRQ_CPU
select SERIAL_8250
select SERIAL_8250_CONSOLE
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_SMP
help
Yosemite is an evaluation board for the RM9000x2 processor
select SYS_HAS_CPU_R10000
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_SMP
select GENERIC_HARDIRQS_NO__DO_IRQ
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_LITTLE_ENDIAN
select ZONE_DMA32 if 64BIT
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select GENERIC_HARDIRQS_NO__DO_IRQ
- select SYS_SUPPORTS_KGDB
select GENERIC_GPIO
config SWAP_IO_SPACE
arch/mips/kernel/smtc.c. This debugging option result in significant
overhead so should be disabled in production kernels.
-config KGDB
- bool "Remote GDB kernel debugging"
- depends on DEBUG_KERNEL && SYS_SUPPORTS_KGDB
- select DEBUG_INFO
- help
- If you say Y here, it will be possible to remotely debug the MIPS
- kernel using gdb. This enlarges your kernel image disk size by
- several megabytes and requires a machine with more than 16 MB,
- better 32 MB RAM to avoid excessive linking time. This is only
- useful for kernel hackers. If unsure, say N.
-
-config SYS_SUPPORTS_KGDB
- bool
-
-config GDB_CONSOLE
- bool "Console output to GDB"
- depends on KGDB
- help
- If you are using GDB for remote debugging over a serial port and
- would like kernel messages to be formatted into GDB $O packets so
- that GDB prints them as program output, say 'Y'.
-
config SB1XXX_CORELIS
bool "Corelis Debugger"
depends on SIBYTE_SB1xxx_SOC
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_APM_EMULATION
- select SYS_SUPPORTS_KGDB
au1xxx_irqmap.o clocks.o platform.o power.o setup.o \
sleeper.o cputable.o dma.o dbdma.o gpio.o
-obj-$(CONFIG_KGDB) += dbg_io.o
obj-$(CONFIG_PCI) += pci.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-#include <linux/types.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_KGDB
-
-/*
- * FIXME the user should be able to select the
- * uart to be used for debugging.
- */
-#define DEBUG_BASE UART_DEBUG_BASE
-
-#define UART16550_BAUD_2400 2400
-#define UART16550_BAUD_4800 4800
-#define UART16550_BAUD_9600 9600
-#define UART16550_BAUD_19200 19200
-#define UART16550_BAUD_38400 38400
-#define UART16550_BAUD_57600 57600
-#define UART16550_BAUD_115200 115200
-
-#define UART16550_PARITY_NONE 0
-#define UART16550_PARITY_ODD 0x08
-#define UART16550_PARITY_EVEN 0x18
-#define UART16550_PARITY_MARK 0x28
-#define UART16550_PARITY_SPACE 0x38
-
-#define UART16550_DATA_5BIT 0x0
-#define UART16550_DATA_6BIT 0x1
-#define UART16550_DATA_7BIT 0x2
-#define UART16550_DATA_8BIT 0x3
-
-#define UART16550_STOP_1BIT 0x0
-#define UART16550_STOP_2BIT 0x4
-
-
-#define UART_RX 0 /* Receive buffer */
-#define UART_TX 4 /* Transmit buffer */
-#define UART_IER 8 /* Interrupt Enable Register */
-#define UART_IIR 0xC /* Interrupt ID Register */
-#define UART_FCR 0x10 /* FIFO Control Register */
-#define UART_LCR 0x14 /* Line Control Register */
-#define UART_MCR 0x18 /* Modem Control Register */
-#define UART_LSR 0x1C /* Line Status Register */
-#define UART_MSR 0x20 /* Modem Status Register */
-#define UART_CLK 0x28 /* Baud Rat4e Clock Divider */
-#define UART_MOD_CNTRL 0x100 /* Module Control */
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y) (au_readl(DEBUG_BASE + y) & 0xff)
-#define UART16550_WRITE(y, z) (au_writel(z & 0xff, DEBUG_BASE + y))
-
-extern unsigned long calc_clock(void);
-
-void debugInit(u32 baud, u8 data, u8 parity, u8 stop)
-{
- if (UART16550_READ(UART_MOD_CNTRL) != 0x3)
- UART16550_WRITE(UART_MOD_CNTRL, 3);
- calc_clock();
-
- /* disable interrupts */
- UART16550_WRITE(UART_IER, 0);
-
- /* set up baud rate */
- {
- u32 divisor;
-
- /* set divisor */
- divisor = get_au1x00_uart_baud_base() / baud;
- UART16550_WRITE(UART_CLK, divisor & 0xffff);
- }
-
- /* set data format */
- UART16550_WRITE(UART_LCR, (data | parity | stop));
-}
-
-static int remoteDebugInitialized;
-
-u8 getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_115200,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE,
- UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(UART_LSR) & 0x1) == 0);
- return UART16550_READ(UART_RX);
-}
-
-
-int putDebugChar(u8 byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_115200,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE,
- UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(UART_LSR) & 0x40) == 0);
- UART16550_WRITE(UART_TX, byte);
-
- return 1;
-}
-
-#endif
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x08000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x08000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
obj-$(CONFIG_BASLER_EXCITE) += excite_irq.o excite_prom.o excite_setup.o \
excite_device.o excite_procfs.o
-obj-$(CONFIG_KGDB) += excite_dbg_io.o
obj-m += excite_iodev.o
+++ /dev/null
-/*
- * Copyright (C) 2004 by Basler Vision Technologies AG
- * Author: Thomas Koeller <thomas.koeller@baslerweb.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/linkage.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <asm/gdb-stub.h>
-#include <asm/rm9k-ocd.h>
-#include <excite.h>
-
-#if defined(CONFIG_SERIAL_8250) && CONFIG_SERIAL_8250_NR_UARTS > 1
-#error Debug port used by serial driver
-#endif
-
-#define UART_CLK 25000000
-#define BASE_BAUD (UART_CLK / 16)
-#define REGISTER_BASE_0 0x0208UL
-#define REGISTER_BASE_1 0x0238UL
-
-#define REGISTER_BASE_DBG REGISTER_BASE_1
-
-#define CPRR 0x0004
-#define UACFG 0x0200
-#define UAINTS 0x0204
-#define UARBR (REGISTER_BASE_DBG + 0x0000)
-#define UATHR (REGISTER_BASE_DBG + 0x0004)
-#define UADLL (REGISTER_BASE_DBG + 0x0008)
-#define UAIER (REGISTER_BASE_DBG + 0x000c)
-#define UADLH (REGISTER_BASE_DBG + 0x0010)
-#define UAIIR (REGISTER_BASE_DBG + 0x0014)
-#define UAFCR (REGISTER_BASE_DBG + 0x0018)
-#define UALCR (REGISTER_BASE_DBG + 0x001c)
-#define UAMCR (REGISTER_BASE_DBG + 0x0020)
-#define UALSR (REGISTER_BASE_DBG + 0x0024)
-#define UAMSR (REGISTER_BASE_DBG + 0x0028)
-#define UASCR (REGISTER_BASE_DBG + 0x002c)
-
-#define PARITY_NONE 0
-#define PARITY_ODD 0x08
-#define PARITY_EVEN 0x18
-#define PARITY_MARK 0x28
-#define PARITY_SPACE 0x38
-
-#define DATA_5BIT 0x0
-#define DATA_6BIT 0x1
-#define DATA_7BIT 0x2
-#define DATA_8BIT 0x3
-
-#define STOP_1BIT 0x0
-#define STOP_2BIT 0x4
-
-#define BAUD_DBG 57600
-#define PARITY_DBG PARITY_NONE
-#define DATA_DBG DATA_8BIT
-#define STOP_DBG STOP_1BIT
-
-/* Initialize the serial port for KGDB debugging */
-void __init excite_kgdb_init(void)
-{
- const u32 divisor = BASE_BAUD / BAUD_DBG;
-
- /* Take the UART out of reset */
- titan_writel(0x00ff1cff, CPRR);
- titan_writel(0x00000000, UACFG);
- titan_writel(0x00000002, UACFG);
-
- titan_writel(0x0, UALCR);
- titan_writel(0x0, UAIER);
-
- /* Disable FIFOs */
- titan_writel(0x00, UAFCR);
-
- titan_writel(0x80, UALCR);
- titan_writel(divisor & 0xff, UADLL);
- titan_writel((divisor & 0xff00) >> 8, UADLH);
- titan_writel(0x0, UALCR);
-
- titan_writel(DATA_DBG | PARITY_DBG | STOP_DBG, UALCR);
-
- /* Enable receiver interrupt */
- titan_readl(UARBR);
- titan_writel(0x1, UAIER);
-}
-
-int getDebugChar(void)
-{
- while (!(titan_readl(UALSR) & 0x1));
- return titan_readl(UARBR);
-}
-
-int putDebugChar(int data)
-{
- while (!(titan_readl(UALSR) & 0x20));
- titan_writel(data, UATHR);
- return 1;
-}
-
-/* KGDB interrupt handler */
-asmlinkage void excite_kgdb_inthdl(void)
-{
- if (unlikely(
- ((titan_readl(UAIIR) & 0x7) == 4)
- && ((titan_readl(UARBR) & 0xff) == 0x3)))
- set_async_breakpoint(®s->cp0_epc);
-}
mips_cpu_irq_init();
rm7k_cpu_irq_init();
rm9k_cpu_irq_init();
-
-#ifdef CONFIG_KGDB
- excite_kgdb_init();
-#endif
}
asmlinkage void plat_irq_dispatch(void)
msgint = msgintflags & msgintmask & (0x1 << (TITAN_MSGINT % 0x20));
if ((pending & (1 << TITAN_IRQ)) && msgint) {
ocd_writel(msgint, INTP0Clear0 + (TITAN_MSGINT / 0x20 * 0x10));
-#if defined(CONFIG_KGDB)
- excite_kgdb_inthdl();
-#endif
do_IRQ(TITAN_IRQ);
return;
}
/* Take the DUART out of reset */
titan_writel(0x00ff1cff, CPRR);
-#if defined(CONFIG_KGDB) || (CONFIG_SERIAL_8250_NR_UARTS > 1)
+#if (CONFIG_SERIAL_8250_NR_UARTS > 1)
/* Enable both ports */
titan_writel(MASK_SER0 | MASK_SER1, UACFG);
#else
/* Enable port #0 only */
titan_writel(MASK_SER0, UACFG);
-#endif /* defined(CONFIG_KGDB) */
+#endif
/*
* Set up serial port #0. Do not use autodetection; the result is
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc5
-# Thu Sep 6 13:14:29 2007
+# Linux kernel version: 2.6.26
+# Fri Jul 25 10:25:34 2008
#
CONFIG_MIPS=y
#
# CONFIG_MACH_ALCHEMY is not set
# CONFIG_BASLER_EXCITE is not set
+# CONFIG_BCM47XX is not set
CONFIG_MIPS_COBALT=y
# CONFIG_MACH_DECSTATION is not set
# CONFIG_MACH_JAZZ is not set
+# CONFIG_LASAT is not set
# CONFIG_LEMOTE_FULONG is not set
# CONFIG_MIPS_MALTA is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_SGI_IP22 is not set
# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
# CONFIG_SGI_IP32 is not set
# CONFIG_SIBYTE_CRHINE is not set
# CONFIG_SIBYTE_CARMEL is not set
# CONFIG_SIBYTE_SENTOSA is not set
# CONFIG_SIBYTE_BIGSUR is not set
# CONFIG_SNI_RM is not set
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
+# CONFIG_MACH_TX39XX is not set
+# CONFIG_MACH_TX49XX is not set
+# CONFIG_MIKROTIK_RB532 is not set
# CONFIG_WR_PPMC is not set
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_CEVT_GT641XX=y
+CONFIG_CEVT_R4K=y
+CONFIG_CSRC_R4K=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_DMA_NEED_PCI_MAP_STATE=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_48 is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_128 is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
CONFIG_RELAY=y
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_PCSPKR_PLATFORM=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# Bus options (PCI, PCMCIA, EISA, ISA, TC)
#
CONFIG_HW_HAS_PCI=y
CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
CONFIG_MMU=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+CONFIG_I8253=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Power management options
#
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
#
# Networking
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
+# CONFIG_XFRM_STATISTICS is not set
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
CONFIG_MTD_PHYSMAP_START=0x0
CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=0
+# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
#
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
CONFIG_PATA_VIA=y
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
+# CONFIG_FUSION is not set
#
-# Fusion MPT device support
+# IEEE 1394 (FireWire) support
#
-# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
-# IEEE 1394 (FireWire) support
+# Enable only one of the two stacks, unless you know what you are doing
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
-# CONFIG_RTC is not set
-CONFIG_COBALT_LCD=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
# CONFIG_DAB is not set
#
# Graphics support
#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+# CONFIG_FB_ASILIANT is not set
+# CONFIG_FB_IMSTT is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_NVIDIA is not set
+# CONFIG_FB_RIVA is not set
+# CONFIG_FB_MATROX is not set
+# CONFIG_FB_RADEON is not set
+# CONFIG_FB_ATY128 is not set
+# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
+# CONFIG_FB_SAVAGE is not set
+# CONFIG_FB_SIS is not set
+# CONFIG_FB_NEOMAGIC is not set
+# CONFIG_FB_KYRO is not set
+# CONFIG_FB_3DFX is not set
+# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
+# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_COBALT=y
+# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+# CONFIG_LOGO is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
#
# USB Input Devices
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=m
-# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
#
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-CONFIG_USB_MON=y
+# CONFIG_USB_MON is not set
#
# USB port drivers
#
-
-#
-# USB Serial Converter support
-#
# CONFIG_USB_SERIAL is not set
#
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
-
-#
-# USB DSL modem support
-#
-
-#
-# USB Gadget Support
-#
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_TRIGGERS=y
# CONFIG_LEDS_TRIGGER_TIMER is not set
# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
+# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4DEV_FS=y
+CONFIG_EXT4DEV_FS_XATTR=y
+CONFIG_EXT4DEV_FS_POSIX_ACL=y
+CONFIG_EXT4DEV_FS_SECURITY=y
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
+CONFIG_JBD2=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
CONFIG_CONFIGFS_FS=y
#
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
# CONFIG_NFSD_V4 is not set
-CONFIG_NFSD_TCP=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_CROSSCOMPILE=y
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
CONFIG_CMDLINE=""
#
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
-# CONFIG_CRYPTO is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=y
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE="mem=48M"
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
# CONFIG_DEBUG_KERNEL is not set
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
# CONFIG_RUNTIME_DEBUG is not set
# CONFIG_MIPS_UNCACHED is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
+CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
# CONFIG_RUNTIME_DEBUG is not set
#
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_CROSSCOMPILE=y
-CONFIG_CMDLINE="console=ttyS1,38400n8 kgdb=ttyS0 root=/dev/nfs ip=bootp"
+CONFIG_CMDLINE="console=ttyS1,38400n8 root=/dev/nfs ip=bootp"
# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
# CONFIG_RUNTIME_DEBUG is not set
#
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_SAMPLES is not set
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
#
# Security options
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_SAMPLES is not set
CONFIG_CMDLINE=""
-CONFIG_SYS_SUPPORTS_KGDB=y
# CONFIG_SB1XXX_CORELIS is not set
#
CONFIG_CROSSCOMPILE=y
CONFIG_CMDLINE=""
# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_KGDB is not set
-CONFIG_SYS_SUPPORTS_KGDB=y
# CONFIG_RUNTIME_DEBUG is not set
#
#include <asm/bcache.h>
#include <asm/irq.h>
#include <asm/reboot.h>
-#include <asm/gdb-stub.h>
#include <asm/traps.h>
#include <asm/debug.h>
#include <linux/types.h>
#include <linux/initrd.h>
#include <linux/irq.h>
-#include <linux/ide.h>
#include <linux/ioport.h>
#include <linux/param.h> /* for HZ */
#include <linux/root_dev.h>
#include <asm/bcache.h>
#include <asm/irq.h>
#include <asm/reboot.h>
-#include <asm/gdb-stub.h>
#include <asm/traps.h>
#include <asm/debug.h>
* Copyright (C) 2007 by Thomas Bogendoerfer
*/
#include <linux/eisa.h>
-#include <linux/hdreg.h>
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/sched.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/fb.h>
-#include <linux/ide.h>
#include <linux/pm.h>
#include <linux/screen_info.h>
#include <linux/platform_device.h>
obj-$(CONFIG_MIPS32_N32) += binfmt_elfn32.o scall64-n32.o signal_n32.o
obj-$(CONFIG_MIPS32_O32) += binfmt_elfo32.o scall64-o32.o
-obj-$(CONFIG_KGDB) += gdb-low.o gdb-stub.o
+obj-$(CONFIG_KGDB) += kgdb.o
obj-$(CONFIG_PROC_FS) += proc.o
obj-$(CONFIG_64BIT) += cpu-bugs64.o
+++ /dev/null
-/*
- * gdb-low.S contains the low-level trap handler for the GDB stub.
- *
- * Copyright (C) 1995 Andreas Busse
- */
-#include <linux/sys.h>
-
-#include <asm/asm.h>
-#include <asm/errno.h>
-#include <asm/irqflags.h>
-#include <asm/mipsregs.h>
-#include <asm/regdef.h>
-#include <asm/stackframe.h>
-#include <asm/gdb-stub.h>
-
-#ifdef CONFIG_32BIT
-#define DMFC0 mfc0
-#define DMTC0 mtc0
-#define LDC1 lwc1
-#define SDC1 lwc1
-#endif
-#ifdef CONFIG_64BIT
-#define DMFC0 dmfc0
-#define DMTC0 dmtc0
-#define LDC1 ldc1
-#define SDC1 ldc1
-#endif
-
-/*
- * [jsun] We reserves about 2x GDB_FR_SIZE in stack. The lower (addressed)
- * part is used to store registers and passed to exception handler.
- * The upper part is reserved for "call func" feature where gdb client
- * saves some of the regs, setups call frame and passes args.
- *
- * A trace shows about 200 bytes are used to store about half of all regs.
- * The rest should be big enough for frame setup and passing args.
- */
-
-/*
- * The low level trap handler
- */
- .align 5
- NESTED(trap_low, GDB_FR_SIZE, sp)
- .set noat
- .set noreorder
-
- mfc0 k0, CP0_STATUS
- sll k0, 3 /* extract cu0 bit */
- bltz k0, 1f
- move k1, sp
-
- /*
- * Called from user mode, go somewhere else.
- */
- mfc0 k0, CP0_CAUSE
- andi k0, k0, 0x7c
-#ifdef CONFIG_64BIT
- dsll k0, k0, 1
-#endif
- PTR_L k1, saved_vectors(k0)
- jr k1
- nop
-1:
- move k0, sp
- PTR_SUBU sp, k1, GDB_FR_SIZE*2 # see comment above
- LONG_S k0, GDB_FR_REG29(sp)
- LONG_S $2, GDB_FR_REG2(sp)
-
-/*
- * First save the CP0 and special registers
- */
-
- mfc0 v0, CP0_STATUS
- LONG_S v0, GDB_FR_STATUS(sp)
- mfc0 v0, CP0_CAUSE
- LONG_S v0, GDB_FR_CAUSE(sp)
- DMFC0 v0, CP0_EPC
- LONG_S v0, GDB_FR_EPC(sp)
- DMFC0 v0, CP0_BADVADDR
- LONG_S v0, GDB_FR_BADVADDR(sp)
- mfhi v0
- LONG_S v0, GDB_FR_HI(sp)
- mflo v0
- LONG_S v0, GDB_FR_LO(sp)
-
-/*
- * Now the integer registers
- */
-
- LONG_S zero, GDB_FR_REG0(sp) /* I know... */
- LONG_S $1, GDB_FR_REG1(sp)
- /* v0 already saved */
- LONG_S $3, GDB_FR_REG3(sp)
- LONG_S $4, GDB_FR_REG4(sp)
- LONG_S $5, GDB_FR_REG5(sp)
- LONG_S $6, GDB_FR_REG6(sp)
- LONG_S $7, GDB_FR_REG7(sp)
- LONG_S $8, GDB_FR_REG8(sp)
- LONG_S $9, GDB_FR_REG9(sp)
- LONG_S $10, GDB_FR_REG10(sp)
- LONG_S $11, GDB_FR_REG11(sp)
- LONG_S $12, GDB_FR_REG12(sp)
- LONG_S $13, GDB_FR_REG13(sp)
- LONG_S $14, GDB_FR_REG14(sp)
- LONG_S $15, GDB_FR_REG15(sp)
- LONG_S $16, GDB_FR_REG16(sp)
- LONG_S $17, GDB_FR_REG17(sp)
- LONG_S $18, GDB_FR_REG18(sp)
- LONG_S $19, GDB_FR_REG19(sp)
- LONG_S $20, GDB_FR_REG20(sp)
- LONG_S $21, GDB_FR_REG21(sp)
- LONG_S $22, GDB_FR_REG22(sp)
- LONG_S $23, GDB_FR_REG23(sp)
- LONG_S $24, GDB_FR_REG24(sp)
- LONG_S $25, GDB_FR_REG25(sp)
- LONG_S $26, GDB_FR_REG26(sp)
- LONG_S $27, GDB_FR_REG27(sp)
- LONG_S $28, GDB_FR_REG28(sp)
- /* sp already saved */
- LONG_S $30, GDB_FR_REG30(sp)
- LONG_S $31, GDB_FR_REG31(sp)
-
- CLI /* disable interrupts */
- TRACE_IRQS_OFF
-
-/*
- * Followed by the floating point registers
- */
- mfc0 v0, CP0_STATUS /* FPU enabled? */
- srl v0, v0, 16
- andi v0, v0, (ST0_CU1 >> 16)
-
- beqz v0,2f /* disabled, skip */
- nop
-
- SDC1 $0, GDB_FR_FPR0(sp)
- SDC1 $1, GDB_FR_FPR1(sp)
- SDC1 $2, GDB_FR_FPR2(sp)
- SDC1 $3, GDB_FR_FPR3(sp)
- SDC1 $4, GDB_FR_FPR4(sp)
- SDC1 $5, GDB_FR_FPR5(sp)
- SDC1 $6, GDB_FR_FPR6(sp)
- SDC1 $7, GDB_FR_FPR7(sp)
- SDC1 $8, GDB_FR_FPR8(sp)
- SDC1 $9, GDB_FR_FPR9(sp)
- SDC1 $10, GDB_FR_FPR10(sp)
- SDC1 $11, GDB_FR_FPR11(sp)
- SDC1 $12, GDB_FR_FPR12(sp)
- SDC1 $13, GDB_FR_FPR13(sp)
- SDC1 $14, GDB_FR_FPR14(sp)
- SDC1 $15, GDB_FR_FPR15(sp)
- SDC1 $16, GDB_FR_FPR16(sp)
- SDC1 $17, GDB_FR_FPR17(sp)
- SDC1 $18, GDB_FR_FPR18(sp)
- SDC1 $19, GDB_FR_FPR19(sp)
- SDC1 $20, GDB_FR_FPR20(sp)
- SDC1 $21, GDB_FR_FPR21(sp)
- SDC1 $22, GDB_FR_FPR22(sp)
- SDC1 $23, GDB_FR_FPR23(sp)
- SDC1 $24, GDB_FR_FPR24(sp)
- SDC1 $25, GDB_FR_FPR25(sp)
- SDC1 $26, GDB_FR_FPR26(sp)
- SDC1 $27, GDB_FR_FPR27(sp)
- SDC1 $28, GDB_FR_FPR28(sp)
- SDC1 $29, GDB_FR_FPR29(sp)
- SDC1 $30, GDB_FR_FPR30(sp)
- SDC1 $31, GDB_FR_FPR31(sp)
-
-/*
- * FPU control registers
- */
-
- cfc1 v0, CP1_STATUS
- LONG_S v0, GDB_FR_FSR(sp)
- cfc1 v0, CP1_REVISION
- LONG_S v0, GDB_FR_FIR(sp)
-
-/*
- * Current stack frame ptr
- */
-
-2:
- LONG_S sp, GDB_FR_FRP(sp)
-
-/*
- * CP0 registers (R4000/R4400 unused registers skipped)
- */
-
- mfc0 v0, CP0_INDEX
- LONG_S v0, GDB_FR_CP0_INDEX(sp)
- mfc0 v0, CP0_RANDOM
- LONG_S v0, GDB_FR_CP0_RANDOM(sp)
- DMFC0 v0, CP0_ENTRYLO0
- LONG_S v0, GDB_FR_CP0_ENTRYLO0(sp)
- DMFC0 v0, CP0_ENTRYLO1
- LONG_S v0, GDB_FR_CP0_ENTRYLO1(sp)
- DMFC0 v0, CP0_CONTEXT
- LONG_S v0, GDB_FR_CP0_CONTEXT(sp)
- mfc0 v0, CP0_PAGEMASK
- LONG_S v0, GDB_FR_CP0_PAGEMASK(sp)
- mfc0 v0, CP0_WIRED
- LONG_S v0, GDB_FR_CP0_WIRED(sp)
- DMFC0 v0, CP0_ENTRYHI
- LONG_S v0, GDB_FR_CP0_ENTRYHI(sp)
- mfc0 v0, CP0_PRID
- LONG_S v0, GDB_FR_CP0_PRID(sp)
-
- .set at
-
-/*
- * Continue with the higher level handler
- */
-
- move a0,sp
-
- jal handle_exception
- nop
-
-/*
- * Restore all writable registers, in reverse order
- */
-
- .set noat
-
- LONG_L v0, GDB_FR_CP0_ENTRYHI(sp)
- LONG_L v1, GDB_FR_CP0_WIRED(sp)
- DMTC0 v0, CP0_ENTRYHI
- mtc0 v1, CP0_WIRED
- LONG_L v0, GDB_FR_CP0_PAGEMASK(sp)
- LONG_L v1, GDB_FR_CP0_ENTRYLO1(sp)
- mtc0 v0, CP0_PAGEMASK
- DMTC0 v1, CP0_ENTRYLO1
- LONG_L v0, GDB_FR_CP0_ENTRYLO0(sp)
- LONG_L v1, GDB_FR_CP0_INDEX(sp)
- DMTC0 v0, CP0_ENTRYLO0
- LONG_L v0, GDB_FR_CP0_CONTEXT(sp)
- mtc0 v1, CP0_INDEX
- DMTC0 v0, CP0_CONTEXT
-
-
-/*
- * Next, the floating point registers
- */
- mfc0 v0, CP0_STATUS /* check if the FPU is enabled */
- srl v0, v0, 16
- andi v0, v0, (ST0_CU1 >> 16)
-
- beqz v0, 3f /* disabled, skip */
- nop
-
- LDC1 $31, GDB_FR_FPR31(sp)
- LDC1 $30, GDB_FR_FPR30(sp)
- LDC1 $29, GDB_FR_FPR29(sp)
- LDC1 $28, GDB_FR_FPR28(sp)
- LDC1 $27, GDB_FR_FPR27(sp)
- LDC1 $26, GDB_FR_FPR26(sp)
- LDC1 $25, GDB_FR_FPR25(sp)
- LDC1 $24, GDB_FR_FPR24(sp)
- LDC1 $23, GDB_FR_FPR23(sp)
- LDC1 $22, GDB_FR_FPR22(sp)
- LDC1 $21, GDB_FR_FPR21(sp)
- LDC1 $20, GDB_FR_FPR20(sp)
- LDC1 $19, GDB_FR_FPR19(sp)
- LDC1 $18, GDB_FR_FPR18(sp)
- LDC1 $17, GDB_FR_FPR17(sp)
- LDC1 $16, GDB_FR_FPR16(sp)
- LDC1 $15, GDB_FR_FPR15(sp)
- LDC1 $14, GDB_FR_FPR14(sp)
- LDC1 $13, GDB_FR_FPR13(sp)
- LDC1 $12, GDB_FR_FPR12(sp)
- LDC1 $11, GDB_FR_FPR11(sp)
- LDC1 $10, GDB_FR_FPR10(sp)
- LDC1 $9, GDB_FR_FPR9(sp)
- LDC1 $8, GDB_FR_FPR8(sp)
- LDC1 $7, GDB_FR_FPR7(sp)
- LDC1 $6, GDB_FR_FPR6(sp)
- LDC1 $5, GDB_FR_FPR5(sp)
- LDC1 $4, GDB_FR_FPR4(sp)
- LDC1 $3, GDB_FR_FPR3(sp)
- LDC1 $2, GDB_FR_FPR2(sp)
- LDC1 $1, GDB_FR_FPR1(sp)
- LDC1 $0, GDB_FR_FPR0(sp)
-
-/*
- * Now the CP0 and integer registers
- */
-
-3:
-#ifdef CONFIG_MIPS_MT_SMTC
- /* Read-modify write of Status must be atomic */
- mfc0 t2, CP0_TCSTATUS
- ori t1, t2, TCSTATUS_IXMT
- mtc0 t1, CP0_TCSTATUS
- andi t2, t2, TCSTATUS_IXMT
- _ehb
- DMT 9 # dmt t1
- jal mips_ihb
- nop
-#endif /* CONFIG_MIPS_MT_SMTC */
- mfc0 t0, CP0_STATUS
- ori t0, 0x1f
- xori t0, 0x1f
- mtc0 t0, CP0_STATUS
-#ifdef CONFIG_MIPS_MT_SMTC
- andi t1, t1, VPECONTROL_TE
- beqz t1, 9f
- nop
- EMT # emt
-9:
- mfc0 t1, CP0_TCSTATUS
- xori t1, t1, TCSTATUS_IXMT
- or t1, t1, t2
- mtc0 t1, CP0_TCSTATUS
- _ehb
-#endif /* CONFIG_MIPS_MT_SMTC */
- LONG_L v0, GDB_FR_STATUS(sp)
- LONG_L v1, GDB_FR_EPC(sp)
- mtc0 v0, CP0_STATUS
- DMTC0 v1, CP0_EPC
- LONG_L v0, GDB_FR_HI(sp)
- LONG_L v1, GDB_FR_LO(sp)
- mthi v0
- mtlo v1
- LONG_L $31, GDB_FR_REG31(sp)
- LONG_L $30, GDB_FR_REG30(sp)
- LONG_L $28, GDB_FR_REG28(sp)
- LONG_L $27, GDB_FR_REG27(sp)
- LONG_L $26, GDB_FR_REG26(sp)
- LONG_L $25, GDB_FR_REG25(sp)
- LONG_L $24, GDB_FR_REG24(sp)
- LONG_L $23, GDB_FR_REG23(sp)
- LONG_L $22, GDB_FR_REG22(sp)
- LONG_L $21, GDB_FR_REG21(sp)
- LONG_L $20, GDB_FR_REG20(sp)
- LONG_L $19, GDB_FR_REG19(sp)
- LONG_L $18, GDB_FR_REG18(sp)
- LONG_L $17, GDB_FR_REG17(sp)
- LONG_L $16, GDB_FR_REG16(sp)
- LONG_L $15, GDB_FR_REG15(sp)
- LONG_L $14, GDB_FR_REG14(sp)
- LONG_L $13, GDB_FR_REG13(sp)
- LONG_L $12, GDB_FR_REG12(sp)
- LONG_L $11, GDB_FR_REG11(sp)
- LONG_L $10, GDB_FR_REG10(sp)
- LONG_L $9, GDB_FR_REG9(sp)
- LONG_L $8, GDB_FR_REG8(sp)
- LONG_L $7, GDB_FR_REG7(sp)
- LONG_L $6, GDB_FR_REG6(sp)
- LONG_L $5, GDB_FR_REG5(sp)
- LONG_L $4, GDB_FR_REG4(sp)
- LONG_L $3, GDB_FR_REG3(sp)
- LONG_L $2, GDB_FR_REG2(sp)
- LONG_L $1, GDB_FR_REG1(sp)
-#if defined(CONFIG_CPU_R3000) || defined(CONFIG_CPU_TX39XX)
- LONG_L k0, GDB_FR_EPC(sp)
- LONG_L $29, GDB_FR_REG29(sp) /* Deallocate stack */
- jr k0
- rfe
-#else
- LONG_L sp, GDB_FR_REG29(sp) /* Deallocate stack */
-
- .set mips3
- eret
- .set mips0
-#endif
- .set at
- .set reorder
- END(trap_low)
-
-LEAF(kgdb_read_byte)
-4: lb t0, (a0)
- sb t0, (a1)
- li v0, 0
- jr ra
- .section __ex_table,"a"
- PTR 4b, kgdbfault
- .previous
- END(kgdb_read_byte)
-
-LEAF(kgdb_write_byte)
-5: sb a0, (a1)
- li v0, 0
- jr ra
- .section __ex_table,"a"
- PTR 5b, kgdbfault
- .previous
- END(kgdb_write_byte)
-
- .type kgdbfault@function
- .ent kgdbfault
-
-kgdbfault: li v0, -EFAULT
- jr ra
- .end kgdbfault
+++ /dev/null
-/*
- * arch/mips/kernel/gdb-stub.c
- *
- * Originally written by Glenn Engel, Lake Stevens Instrument Division
- *
- * Contributed by HP Systems
- *
- * Modified for SPARC by Stu Grossman, Cygnus Support.
- *
- * Modified for Linux/MIPS (and MIPS in general) by Andreas Busse
- * Send complaints, suggestions etc. to <andy@waldorf-gmbh.de>
- *
- * Copyright (C) 1995 Andreas Busse
- *
- * Copyright (C) 2003 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- */
-
-/*
- * To enable debugger support, two things need to happen. One, a
- * call to set_debug_traps() is necessary in order to allow any breakpoints
- * or error conditions to be properly intercepted and reported to gdb.
- * Two, a breakpoint needs to be generated to begin communication. This
- * is most easily accomplished by a call to breakpoint(). Breakpoint()
- * simulates a breakpoint by executing a BREAK instruction.
- *
- *
- * The following gdb commands are supported:
- *
- * command function Return value
- *
- * g return the value of the CPU registers hex data or ENN
- * G set the value of the CPU registers OK or ENN
- *
- * mAA..AA,LLLL Read LLLL bytes at address AA..AA hex data or ENN
- * MAA..AA,LLLL: Write LLLL bytes at address AA.AA OK or ENN
- *
- * c Resume at current address SNN ( signal NN)
- * cAA..AA Continue at address AA..AA SNN
- *
- * s Step one instruction SNN
- * sAA..AA Step one instruction from AA..AA SNN
- *
- * k kill
- *
- * ? What was the last sigval ? SNN (signal NN)
- *
- * bBB..BB Set baud rate to BB..BB OK or BNN, then sets
- * baud rate
- *
- * All commands and responses are sent with a packet which includes a
- * checksum. A packet consists of
- *
- * $<packet info>#<checksum>.
- *
- * where
- * <packet info> :: <characters representing the command or response>
- * <checksum> :: < two hex digits computed as modulo 256 sum of <packetinfo>>
- *
- * When a packet is received, it is first acknowledged with either '+' or '-'.
- * '+' indicates a successful transfer. '-' indicates a failed transfer.
- *
- * Example:
- *
- * Host: Reply:
- * $m0,10#2a +$00010203040506070809101112131415#42
- *
- *
- * ==============
- * MORE EXAMPLES:
- * ==============
- *
- * For reference -- the following are the steps that one
- * company took (RidgeRun Inc) to get remote gdb debugging
- * going. In this scenario the host machine was a PC and the
- * target platform was a Galileo EVB64120A MIPS evaluation
- * board.
- *
- * Step 1:
- * First download gdb-5.0.tar.gz from the internet.
- * and then build/install the package.
- *
- * Example:
- * $ tar zxf gdb-5.0.tar.gz
- * $ cd gdb-5.0
- * $ ./configure --target=mips-linux-elf
- * $ make
- * $ install
- * $ which mips-linux-elf-gdb
- * /usr/local/bin/mips-linux-elf-gdb
- *
- * Step 2:
- * Configure linux for remote debugging and build it.
- *
- * Example:
- * $ cd ~/linux
- * $ make menuconfig <go to "Kernel Hacking" and turn on remote debugging>
- * $ make
- *
- * Step 3:
- * Download the kernel to the remote target and start
- * the kernel running. It will promptly halt and wait
- * for the host gdb session to connect. It does this
- * since the "Kernel Hacking" option has defined
- * CONFIG_KGDB which in turn enables your calls
- * to:
- * set_debug_traps();
- * breakpoint();
- *
- * Step 4:
- * Start the gdb session on the host.
- *
- * Example:
- * $ mips-linux-elf-gdb vmlinux
- * (gdb) set remotebaud 115200
- * (gdb) target remote /dev/ttyS1
- * ...at this point you are connected to
- * the remote target and can use gdb
- * in the normal fasion. Setting
- * breakpoints, single stepping,
- * printing variables, etc.
- */
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/init.h>
-#include <linux/smp.h>
-#include <linux/spinlock.h>
-#include <linux/slab.h>
-#include <linux/reboot.h>
-
-#include <asm/asm.h>
-#include <asm/cacheflush.h>
-#include <asm/mipsregs.h>
-#include <asm/pgtable.h>
-#include <asm/system.h>
-#include <asm/gdb-stub.h>
-#include <asm/inst.h>
-
-/*
- * external low-level support routines
- */
-
-extern int putDebugChar(char c); /* write a single character */
-extern char getDebugChar(void); /* read and return a single char */
-extern void trap_low(void);
-
-/*
- * breakpoint and test functions
- */
-extern void breakpoint(void);
-extern void breakinst(void);
-extern void async_breakpoint(void);
-extern void async_breakinst(void);
-extern void adel(void);
-
-/*
- * local prototypes
- */
-
-static void getpacket(char *buffer);
-static void putpacket(char *buffer);
-static int computeSignal(int tt);
-static int hex(unsigned char ch);
-static int hexToInt(char **ptr, int *intValue);
-static int hexToLong(char **ptr, long *longValue);
-static unsigned char *mem2hex(char *mem, char *buf, int count, int may_fault);
-void handle_exception(struct gdb_regs *regs);
-
-int kgdb_enabled;
-
-/*
- * spin locks for smp case
- */
-static DEFINE_SPINLOCK(kgdb_lock);
-static raw_spinlock_t kgdb_cpulock[NR_CPUS] = {
- [0 ... NR_CPUS-1] = __RAW_SPIN_LOCK_UNLOCKED,
-};
-
-/*
- * BUFMAX defines the maximum number of characters in inbound/outbound buffers
- * at least NUMREGBYTES*2 are needed for register packets
- */
-#define BUFMAX 2048
-
-static char input_buffer[BUFMAX];
-static char output_buffer[BUFMAX];
-static int initialized; /* !0 means we've been initialized */
-static int kgdb_started;
-static const char hexchars[]="0123456789abcdef";
-
-/* Used to prevent crashes in memory access. Note that they'll crash anyway if
- we haven't set up fault handlers yet... */
-int kgdb_read_byte(unsigned char *address, unsigned char *dest);
-int kgdb_write_byte(unsigned char val, unsigned char *dest);
-
-/*
- * Convert ch from a hex digit to an int
- */
-static int hex(unsigned char ch)
-{
- if (ch >= 'a' && ch <= 'f')
- return ch-'a'+10;
- if (ch >= '0' && ch <= '9')
- return ch-'0';
- if (ch >= 'A' && ch <= 'F')
- return ch-'A'+10;
- return -1;
-}
-
-/*
- * scan for the sequence $<data>#<checksum>
- */
-static void getpacket(char *buffer)
-{
- unsigned char checksum;
- unsigned char xmitcsum;
- int i;
- int count;
- unsigned char ch;
-
- do {
- /*
- * wait around for the start character,
- * ignore all other characters
- */
- while ((ch = (getDebugChar() & 0x7f)) != '$') ;
-
- checksum = 0;
- xmitcsum = -1;
- count = 0;
-
- /*
- * now, read until a # or end of buffer is found
- */
- while (count < BUFMAX) {
- ch = getDebugChar();
- if (ch == '#')
- break;
- checksum = checksum + ch;
- buffer[count] = ch;
- count = count + 1;
- }
-
- if (count >= BUFMAX)
- continue;
-
- buffer[count] = 0;
-
- if (ch == '#') {
- xmitcsum = hex(getDebugChar() & 0x7f) << 4;
- xmitcsum |= hex(getDebugChar() & 0x7f);
-
- if (checksum != xmitcsum)
- putDebugChar('-'); /* failed checksum */
- else {
- putDebugChar('+'); /* successful transfer */
-
- /*
- * if a sequence char is present,
- * reply the sequence ID
- */
- if (buffer[2] == ':') {
- putDebugChar(buffer[0]);
- putDebugChar(buffer[1]);
-
- /*
- * remove sequence chars from buffer
- */
- count = strlen(buffer);
- for (i=3; i <= count; i++)
- buffer[i-3] = buffer[i];
- }
- }
- }
- }
- while (checksum != xmitcsum);
-}
-
-/*
- * send the packet in buffer.
- */
-static void putpacket(char *buffer)
-{
- unsigned char checksum;
- int count;
- unsigned char ch;
-
- /*
- * $<packet info>#<checksum>.
- */
-
- do {
- putDebugChar('$');
- checksum = 0;
- count = 0;
-
- while ((ch = buffer[count]) != 0) {
- if (!(putDebugChar(ch)))
- return;
- checksum += ch;
- count += 1;
- }
-
- putDebugChar('#');
- putDebugChar(hexchars[checksum >> 4]);
- putDebugChar(hexchars[checksum & 0xf]);
-
- }
- while ((getDebugChar() & 0x7f) != '+');
-}
-
-
-/*
- * Convert the memory pointed to by mem into hex, placing result in buf.
- * Return a pointer to the last char put in buf (null), in case of mem fault,
- * return 0.
- * may_fault is non-zero if we are reading from arbitrary memory, but is currently
- * not used.
- */
-static unsigned char *mem2hex(char *mem, char *buf, int count, int may_fault)
-{
- unsigned char ch;
-
- while (count-- > 0) {
- if (kgdb_read_byte(mem++, &ch) != 0)
- return 0;
- *buf++ = hexchars[ch >> 4];
- *buf++ = hexchars[ch & 0xf];
- }
-
- *buf = 0;
-
- return buf;
-}
-
-/*
- * convert the hex array pointed to by buf into binary to be placed in mem
- * return a pointer to the character AFTER the last byte written
- * may_fault is non-zero if we are reading from arbitrary memory, but is currently
- * not used.
- */
-static char *hex2mem(char *buf, char *mem, int count, int binary, int may_fault)
-{
- int i;
- unsigned char ch;
-
- for (i=0; i<count; i++)
- {
- if (binary) {
- ch = *buf++;
- if (ch == 0x7d)
- ch = 0x20 ^ *buf++;
- }
- else {
- ch = hex(*buf++) << 4;
- ch |= hex(*buf++);
- }
- if (kgdb_write_byte(ch, mem++) != 0)
- return 0;
- }
-
- return mem;
-}
-
-/*
- * This table contains the mapping between SPARC hardware trap types, and
- * signals, which are primarily what GDB understands. It also indicates
- * which hardware traps we need to commandeer when initializing the stub.
- */
-static struct hard_trap_info {
- unsigned char tt; /* Trap type code for MIPS R3xxx and R4xxx */
- unsigned char signo; /* Signal that we map this trap into */
-} hard_trap_info[] = {
- { 6, SIGBUS }, /* instruction bus error */
- { 7, SIGBUS }, /* data bus error */
- { 9, SIGTRAP }, /* break */
- { 10, SIGILL }, /* reserved instruction */
-/* { 11, SIGILL }, */ /* CPU unusable */
- { 12, SIGFPE }, /* overflow */
- { 13, SIGTRAP }, /* trap */
- { 14, SIGSEGV }, /* virtual instruction cache coherency */
- { 15, SIGFPE }, /* floating point exception */
- { 23, SIGSEGV }, /* watch */
- { 31, SIGSEGV }, /* virtual data cache coherency */
- { 0, 0} /* Must be last */
-};
-
-/* Save the normal trap handlers for user-mode traps. */
-void *saved_vectors[32];
-
-/*
- * Set up exception handlers for tracing and breakpoints
- */
-void set_debug_traps(void)
-{
- struct hard_trap_info *ht;
- unsigned long flags;
- unsigned char c;
-
- local_irq_save(flags);
- for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
- saved_vectors[ht->tt] = set_except_vector(ht->tt, trap_low);
-
- putDebugChar('+'); /* 'hello world' */
- /*
- * In case GDB is started before us, ack any packets
- * (presumably "$?#xx") sitting there.
- */
- while((c = getDebugChar()) != '$');
- while((c = getDebugChar()) != '#');
- c = getDebugChar(); /* eat first csum byte */
- c = getDebugChar(); /* eat second csum byte */
- putDebugChar('+'); /* ack it */
-
- initialized = 1;
- local_irq_restore(flags);
-}
-
-void restore_debug_traps(void)
-{
- struct hard_trap_info *ht;
- unsigned long flags;
-
- local_irq_save(flags);
- for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
- set_except_vector(ht->tt, saved_vectors[ht->tt]);
- local_irq_restore(flags);
-}
-
-/*
- * Convert the MIPS hardware trap type code to a Unix signal number.
- */
-static int computeSignal(int tt)
-{
- struct hard_trap_info *ht;
-
- for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
- if (ht->tt == tt)
- return ht->signo;
-
- return SIGHUP; /* default for things we don't know about */
-}
-
-/*
- * While we find nice hex chars, build an int.
- * Return number of chars processed.
- */
-static int hexToInt(char **ptr, int *intValue)
-{
- int numChars = 0;
- int hexValue;
-
- *intValue = 0;
-
- while (**ptr) {
- hexValue = hex(**ptr);
- if (hexValue < 0)
- break;
-
- *intValue = (*intValue << 4) | hexValue;
- numChars ++;
-
- (*ptr)++;
- }
-
- return (numChars);
-}
-
-static int hexToLong(char **ptr, long *longValue)
-{
- int numChars = 0;
- int hexValue;
-
- *longValue = 0;
-
- while (**ptr) {
- hexValue = hex(**ptr);
- if (hexValue < 0)
- break;
-
- *longValue = (*longValue << 4) | hexValue;
- numChars ++;
-
- (*ptr)++;
- }
-
- return numChars;
-}
-
-
-#if 0
-/*
- * Print registers (on target console)
- * Used only to debug the stub...
- */
-void show_gdbregs(struct gdb_regs * regs)
-{
- /*
- * Saved main processor registers
- */
- printk("$0 : %08lx %08lx %08lx %08lx %08lx %08lx %08lx %08lx\n",
- regs->reg0, regs->reg1, regs->reg2, regs->reg3,
- regs->reg4, regs->reg5, regs->reg6, regs->reg7);
- printk("$8 : %08lx %08lx %08lx %08lx %08lx %08lx %08lx %08lx\n",
- regs->reg8, regs->reg9, regs->reg10, regs->reg11,
- regs->reg12, regs->reg13, regs->reg14, regs->reg15);
- printk("$16: %08lx %08lx %08lx %08lx %08lx %08lx %08lx %08lx\n",
- regs->reg16, regs->reg17, regs->reg18, regs->reg19,
- regs->reg20, regs->reg21, regs->reg22, regs->reg23);
- printk("$24: %08lx %08lx %08lx %08lx %08lx %08lx %08lx %08lx\n",
- regs->reg24, regs->reg25, regs->reg26, regs->reg27,
- regs->reg28, regs->reg29, regs->reg30, regs->reg31);
-
- /*
- * Saved cp0 registers
- */
- printk("epc : %08lx\nStatus: %08lx\nCause : %08lx\n",
- regs->cp0_epc, regs->cp0_status, regs->cp0_cause);
-}
-#endif /* dead code */
-
-/*
- * We single-step by setting breakpoints. When an exception
- * is handled, we need to restore the instructions hoisted
- * when the breakpoints were set.
- *
- * This is where we save the original instructions.
- */
-static struct gdb_bp_save {
- unsigned long addr;
- unsigned int val;
-} step_bp[2];
-
-#define BP 0x0000000d /* break opcode */
-
-/*
- * Set breakpoint instructions for single stepping.
- */
-static void single_step(struct gdb_regs *regs)
-{
- union mips_instruction insn;
- unsigned long targ;
- int is_branch, is_cond, i;
-
- targ = regs->cp0_epc;
- insn.word = *(unsigned int *)targ;
- is_branch = is_cond = 0;
-
- switch (insn.i_format.opcode) {
- /*
- * jr and jalr are in r_format format.
- */
- case spec_op:
- switch (insn.r_format.func) {
- case jalr_op:
- case jr_op:
- targ = *(®s->reg0 + insn.r_format.rs);
- is_branch = 1;
- break;
- }
- break;
-
- /*
- * This group contains:
- * bltz_op, bgez_op, bltzl_op, bgezl_op,
- * bltzal_op, bgezal_op, bltzall_op, bgezall_op.
- */
- case bcond_op:
- is_branch = is_cond = 1;
- targ += 4 + (insn.i_format.simmediate << 2);
- break;
-
- /*
- * These are unconditional and in j_format.
- */
- case jal_op:
- case j_op:
- is_branch = 1;
- targ += 4;
- targ >>= 28;
- targ <<= 28;
- targ |= (insn.j_format.target << 2);
- break;
-
- /*
- * These are conditional.
- */
- case beq_op:
- case beql_op:
- case bne_op:
- case bnel_op:
- case blez_op:
- case blezl_op:
- case bgtz_op:
- case bgtzl_op:
- case cop0_op:
- case cop1_op:
- case cop2_op:
- case cop1x_op:
- is_branch = is_cond = 1;
- targ += 4 + (insn.i_format.simmediate << 2);
- break;
- }
-
- if (is_branch) {
- i = 0;
- if (is_cond && targ != (regs->cp0_epc + 8)) {
- step_bp[i].addr = regs->cp0_epc + 8;
- step_bp[i++].val = *(unsigned *)(regs->cp0_epc + 8);
- *(unsigned *)(regs->cp0_epc + 8) = BP;
- }
- step_bp[i].addr = targ;
- step_bp[i].val = *(unsigned *)targ;
- *(unsigned *)targ = BP;
- } else {
- step_bp[0].addr = regs->cp0_epc + 4;
- step_bp[0].val = *(unsigned *)(regs->cp0_epc + 4);
- *(unsigned *)(regs->cp0_epc + 4) = BP;
- }
-}
-
-/*
- * If asynchronously interrupted by gdb, then we need to set a breakpoint
- * at the interrupted instruction so that we wind up stopped with a
- * reasonable stack frame.
- */
-static struct gdb_bp_save async_bp;
-
-/*
- * Swap the interrupted EPC with our asynchronous breakpoint routine.
- * This is safer than stuffing the breakpoint in-place, since no cache
- * flushes (or resulting smp_call_functions) are required. The
- * assumption is that only one CPU will be handling asynchronous bp's,
- * and only one can be active at a time.
- */
-extern spinlock_t smp_call_lock;
-
-void set_async_breakpoint(unsigned long *epc)
-{
- /* skip breaking into userland */
- if ((*epc & 0x80000000) == 0)
- return;
-
-#ifdef CONFIG_SMP
- /* avoid deadlock if someone is make IPC */
- if (spin_is_locked(&smp_call_lock))
- return;
-#endif
-
- async_bp.addr = *epc;
- *epc = (unsigned long)async_breakpoint;
-}
-
-#ifdef CONFIG_SMP
-static void kgdb_wait(void *arg)
-{
- unsigned flags;
- int cpu = smp_processor_id();
-
- local_irq_save(flags);
-
- __raw_spin_lock(&kgdb_cpulock[cpu]);
- __raw_spin_unlock(&kgdb_cpulock[cpu]);
-
- local_irq_restore(flags);
-}
-#endif
-
-/*
- * GDB stub needs to call kgdb_wait on all processor with interrupts
- * disabled, so it uses it's own special variant.
- */
-static int kgdb_smp_call_kgdb_wait(void)
-{
-#ifdef CONFIG_SMP
- cpumask_t mask = cpu_online_map;
- struct call_data_struct data;
- int cpu = smp_processor_id();
- int cpus;
-
- /*
- * Can die spectacularly if this CPU isn't yet marked online
- */
- BUG_ON(!cpu_online(cpu));
-
- cpu_clear(cpu, mask);
- cpus = cpus_weight(mask);
- if (!cpus)
- return 0;
-
- if (spin_is_locked(&smp_call_lock)) {
- /*
- * Some other processor is trying to make us do something
- * but we're not going to respond... give up
- */
- return -1;
- }
-
- /*
- * We will continue here, accepting the fact that
- * the kernel may deadlock if another CPU attempts
- * to call smp_call_function now...
- */
-
- data.func = kgdb_wait;
- data.info = NULL;
- atomic_set(&data.started, 0);
- data.wait = 0;
-
- spin_lock(&smp_call_lock);
- call_data = &data;
- mb();
-
- core_send_ipi_mask(mask, SMP_CALL_FUNCTION);
-
- /* Wait for response */
- /* FIXME: lock-up detection, backtrace on lock-up */
- while (atomic_read(&data.started) != cpus)
- barrier();
-
- call_data = NULL;
- spin_unlock(&smp_call_lock);
-#endif
-
- return 0;
-}
-
-/*
- * This function does all command processing for interfacing to gdb. It
- * returns 1 if you should skip the instruction at the trap address, 0
- * otherwise.
- */
-void handle_exception(struct gdb_regs *regs)
-{
- int trap; /* Trap type */
- int sigval;
- long addr;
- int length;
- char *ptr;
- unsigned long *stack;
- int i;
- int bflag = 0;
-
- kgdb_started = 1;
-
- /*
- * acquire the big kgdb spinlock
- */
- if (!spin_trylock(&kgdb_lock)) {
- /*
- * some other CPU has the lock, we should go back to
- * receive the gdb_wait IPC
- */
- return;
- }
-
- /*
- * If we're in async_breakpoint(), restore the real EPC from
- * the breakpoint.
- */
- if (regs->cp0_epc == (unsigned long)async_breakinst) {
- regs->cp0_epc = async_bp.addr;
- async_bp.addr = 0;
- }
-
- /*
- * acquire the CPU spinlocks
- */
- for_each_online_cpu(i)
- if (__raw_spin_trylock(&kgdb_cpulock[i]) == 0)
- panic("kgdb: couldn't get cpulock %d\n", i);
-
- /*
- * force other cpus to enter kgdb
- */
- kgdb_smp_call_kgdb_wait();
-
- /*
- * If we're in breakpoint() increment the PC
- */
- trap = (regs->cp0_cause & 0x7c) >> 2;
- if (trap == 9 && regs->cp0_epc == (unsigned long)breakinst)
- regs->cp0_epc += 4;
-
- /*
- * If we were single_stepping, restore the opcodes hoisted
- * for the breakpoint[s].
- */
- if (step_bp[0].addr) {
- *(unsigned *)step_bp[0].addr = step_bp[0].val;
- step_bp[0].addr = 0;
-
- if (step_bp[1].addr) {
- *(unsigned *)step_bp[1].addr = step_bp[1].val;
- step_bp[1].addr = 0;
- }
- }
-
- stack = (long *)regs->reg29; /* stack ptr */
- sigval = computeSignal(trap);
-
- /*
- * reply to host that an exception has occurred
- */
- ptr = output_buffer;
-
- /*
- * Send trap type (converted to signal)
- */
- *ptr++ = 'T';
- *ptr++ = hexchars[sigval >> 4];
- *ptr++ = hexchars[sigval & 0xf];
-
- /*
- * Send Error PC
- */
- *ptr++ = hexchars[REG_EPC >> 4];
- *ptr++ = hexchars[REG_EPC & 0xf];
- *ptr++ = ':';
- ptr = mem2hex((char *)®s->cp0_epc, ptr, sizeof(long), 0);
- *ptr++ = ';';
-
- /*
- * Send frame pointer
- */
- *ptr++ = hexchars[REG_FP >> 4];
- *ptr++ = hexchars[REG_FP & 0xf];
- *ptr++ = ':';
- ptr = mem2hex((char *)®s->reg30, ptr, sizeof(long), 0);
- *ptr++ = ';';
-
- /*
- * Send stack pointer
- */
- *ptr++ = hexchars[REG_SP >> 4];
- *ptr++ = hexchars[REG_SP & 0xf];
- *ptr++ = ':';
- ptr = mem2hex((char *)®s->reg29, ptr, sizeof(long), 0);
- *ptr++ = ';';
-
- *ptr++ = 0;
- putpacket(output_buffer); /* send it off... */
-
- /*
- * Wait for input from remote GDB
- */
- while (1) {
- output_buffer[0] = 0;
- getpacket(input_buffer);
-
- switch (input_buffer[0])
- {
- case '?':
- output_buffer[0] = 'S';
- output_buffer[1] = hexchars[sigval >> 4];
- output_buffer[2] = hexchars[sigval & 0xf];
- output_buffer[3] = 0;
- break;
-
- /*
- * Detach debugger; let CPU run
- */
- case 'D':
- putpacket(output_buffer);
- goto finish_kgdb;
- break;
-
- case 'd':
- /* toggle debug flag */
- break;
-
- /*
- * Return the value of the CPU registers
- */
- case 'g':
- ptr = output_buffer;
- ptr = mem2hex((char *)®s->reg0, ptr, 32*sizeof(long), 0); /* r0...r31 */
- ptr = mem2hex((char *)®s->cp0_status, ptr, 6*sizeof(long), 0); /* cp0 */
- ptr = mem2hex((char *)®s->fpr0, ptr, 32*sizeof(long), 0); /* f0...31 */
- ptr = mem2hex((char *)®s->cp1_fsr, ptr, 2*sizeof(long), 0); /* cp1 */
- ptr = mem2hex((char *)®s->frame_ptr, ptr, 2*sizeof(long), 0); /* frp */
- ptr = mem2hex((char *)®s->cp0_index, ptr, 16*sizeof(long), 0); /* cp0 */
- break;
-
- /*
- * set the value of the CPU registers - return OK
- */
- case 'G':
- {
- ptr = &input_buffer[1];
- hex2mem(ptr, (char *)®s->reg0, 32*sizeof(long), 0, 0);
- ptr += 32*(2*sizeof(long));
- hex2mem(ptr, (char *)®s->cp0_status, 6*sizeof(long), 0, 0);
- ptr += 6*(2*sizeof(long));
- hex2mem(ptr, (char *)®s->fpr0, 32*sizeof(long), 0, 0);
- ptr += 32*(2*sizeof(long));
- hex2mem(ptr, (char *)®s->cp1_fsr, 2*sizeof(long), 0, 0);
- ptr += 2*(2*sizeof(long));
- hex2mem(ptr, (char *)®s->frame_ptr, 2*sizeof(long), 0, 0);
- ptr += 2*(2*sizeof(long));
- hex2mem(ptr, (char *)®s->cp0_index, 16*sizeof(long), 0, 0);
- strcpy(output_buffer, "OK");
- }
- break;
-
- /*
- * mAA..AA,LLLL Read LLLL bytes at address AA..AA
- */
- case 'm':
- ptr = &input_buffer[1];
-
- if (hexToLong(&ptr, &addr)
- && *ptr++ == ','
- && hexToInt(&ptr, &length)) {
- if (mem2hex((char *)addr, output_buffer, length, 1))
- break;
- strcpy(output_buffer, "E03");
- } else
- strcpy(output_buffer, "E01");
- break;
-
- /*
- * XAA..AA,LLLL: Write LLLL escaped binary bytes at address AA.AA
- */
- case 'X':
- bflag = 1;
- /* fall through */
-
- /*
- * MAA..AA,LLLL: Write LLLL bytes at address AA.AA return OK
- */
- case 'M':
- ptr = &input_buffer[1];
-
- if (hexToLong(&ptr, &addr)
- && *ptr++ == ','
- && hexToInt(&ptr, &length)
- && *ptr++ == ':') {
- if (hex2mem(ptr, (char *)addr, length, bflag, 1))
- strcpy(output_buffer, "OK");
- else
- strcpy(output_buffer, "E03");
- }
- else
- strcpy(output_buffer, "E02");
- break;
-
- /*
- * cAA..AA Continue at address AA..AA(optional)
- */
- case 'c':
- /* try to read optional parameter, pc unchanged if no parm */
-
- ptr = &input_buffer[1];
- if (hexToLong(&ptr, &addr))
- regs->cp0_epc = addr;
-
- goto exit_kgdb_exception;
- break;
-
- /*
- * kill the program; let us try to restart the machine
- * Reset the whole machine.
- */
- case 'k':
- case 'r':
- machine_restart("kgdb restarts machine");
- break;
-
- /*
- * Step to next instruction
- */
- case 's':
- /*
- * There is no single step insn in the MIPS ISA, so we
- * use breakpoints and continue, instead.
- */
- single_step(regs);
- goto exit_kgdb_exception;
- /* NOTREACHED */
- break;
-
- /*
- * Set baud rate (bBB)
- * FIXME: Needs to be written
- */
- case 'b':
- {
-#if 0
- int baudrate;
- extern void set_timer_3();
-
- ptr = &input_buffer[1];
- if (!hexToInt(&ptr, &baudrate))
- {
- strcpy(output_buffer, "B01");
- break;
- }
-
- /* Convert baud rate to uart clock divider */
-
- switch (baudrate)
- {
- case 38400:
- baudrate = 16;
- break;
- case 19200:
- baudrate = 33;
- break;
- case 9600:
- baudrate = 65;
- break;
- default:
- baudrate = 0;
- strcpy(output_buffer, "B02");
- goto x1;
- }
-
- if (baudrate) {
- putpacket("OK"); /* Ack before changing speed */
- set_timer_3(baudrate); /* Set it */
- }
-#endif
- }
- break;
-
- } /* switch */
-
- /*
- * reply to the request
- */
-
- putpacket(output_buffer);
-
- } /* while */
-
- return;
-
-finish_kgdb:
- restore_debug_traps();
-
-exit_kgdb_exception:
- /* release locks so other CPUs can go */
- for_each_online_cpu(i)
- __raw_spin_unlock(&kgdb_cpulock[i]);
- spin_unlock(&kgdb_lock);
-
- __flush_cache_all();
- return;
-}
-
-/*
- * This function will generate a breakpoint exception. It is used at the
- * beginning of a program to sync up with a debugger and can be used
- * otherwise as a quick means to stop program execution and "break" into
- * the debugger.
- */
-void breakpoint(void)
-{
- if (!initialized)
- return;
-
- __asm__ __volatile__(
- ".globl breakinst\n\t"
- ".set\tnoreorder\n\t"
- "nop\n"
- "breakinst:\tbreak\n\t"
- "nop\n\t"
- ".set\treorder"
- );
-}
-
-/* Nothing but the break; don't pollute any registers */
-void async_breakpoint(void)
-{
- __asm__ __volatile__(
- ".globl async_breakinst\n\t"
- ".set\tnoreorder\n\t"
- "nop\n"
- "async_breakinst:\tbreak\n\t"
- "nop\n\t"
- ".set\treorder"
- );
-}
-
-void adel(void)
-{
- __asm__ __volatile__(
- ".globl\tadel\n\t"
- "lui\t$8,0x8000\n\t"
- "lw\t$9,1($8)\n\t"
- );
-}
-
-/*
- * malloc is needed by gdb client in "call func()", even a private one
- * will make gdb happy
- */
-static void __used *malloc(size_t size)
-{
- return kmalloc(size, GFP_ATOMIC);
-}
-
-static void __used free(void *where)
-{
- kfree(where);
-}
-
-#ifdef CONFIG_GDB_CONSOLE
-
-void gdb_putsn(const char *str, int l)
-{
- char outbuf[18];
-
- if (!kgdb_started)
- return;
-
- outbuf[0]='O';
-
- while(l) {
- int i = (l>8)?8:l;
- mem2hex((char *)str, &outbuf[1], i, 0);
- outbuf[(i*2)+1]=0;
- putpacket(outbuf);
- str += i;
- l -= i;
- }
-}
-
-static void gdb_console_write(struct console *con, const char *s, unsigned n)
-{
- gdb_putsn(s, n);
-}
-
-static struct console gdb_console = {
- .name = "gdb",
- .write = gdb_console_write,
- .flags = CON_PRINTBUFFER,
- .index = -1
-};
-
-static int __init register_gdb_console(void)
-{
- register_console(&gdb_console);
-
- return 0;
-}
-
-console_initcall(register_gdb_console);
-
-#endif
#include <linux/sched.h>
#include <linux/seq_file.h>
#include <linux/kallsyms.h>
+#include <linux/kgdb.h>
#include <asm/atomic.h>
#include <asm/system.h>
#include <asm/uaccess.h>
+#ifdef CONFIG_KGDB
+int kgdb_early_setup;
+#endif
+
static unsigned long irq_map[NR_IRQS / BITS_PER_LONG];
int allocate_irqno(void)
atomic_inc(&irq_err_count);
}
-#ifdef CONFIG_KGDB
-extern void breakpoint(void);
-extern void set_debug_traps(void);
-
-static int kgdb_flag = 1;
-static int __init nokgdb(char *str)
-{
- kgdb_flag = 0;
- return 1;
-}
-__setup("nokgdb", nokgdb);
-#endif
-
void __init init_IRQ(void)
{
int i;
+#ifdef CONFIG_KGDB
+ if (kgdb_early_setup)
+ return;
+#endif
+
for (i = 0; i < NR_IRQS; i++)
set_irq_noprobe(i);
arch_init_irq();
#ifdef CONFIG_KGDB
- if (kgdb_flag) {
- printk("Wait for gdb client connection ...\n");
- set_debug_traps();
- breakpoint();
- }
+ if (!kgdb_early_setup)
+ kgdb_early_setup = 1;
#endif
}
--- /dev/null
+/*
+ * Originally written by Glenn Engel, Lake Stevens Instrument Division
+ *
+ * Contributed by HP Systems
+ *
+ * Modified for Linux/MIPS (and MIPS in general) by Andreas Busse
+ * Send complaints, suggestions etc. to <andy@waldorf-gmbh.de>
+ *
+ * Copyright (C) 1995 Andreas Busse
+ *
+ * Copyright (C) 2003 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ *
+ * Copyright (C) 2004-2005 MontaVista Software Inc.
+ * Author: Manish Lachwani, mlachwani@mvista.com or manish@koffee-break.com
+ *
+ * Copyright (C) 2007-2008 Wind River Systems, Inc.
+ * Author/Maintainer: Jason Wessel, jason.wessel@windriver.com
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/ptrace.h> /* for linux pt_regs struct */
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
+#include <linux/sched.h>
+#include <asm/inst.h>
+#include <asm/fpu.h>
+#include <asm/cacheflush.h>
+#include <asm/processor.h>
+#include <asm/sigcontext.h>
+
+static struct hard_trap_info {
+ unsigned char tt; /* Trap type code for MIPS R3xxx and R4xxx */
+ unsigned char signo; /* Signal that we map this trap into */
+} hard_trap_info[] = {
+ { 6, SIGBUS }, /* instruction bus error */
+ { 7, SIGBUS }, /* data bus error */
+ { 9, SIGTRAP }, /* break */
+/* { 11, SIGILL }, */ /* CPU unusable */
+ { 12, SIGFPE }, /* overflow */
+ { 13, SIGTRAP }, /* trap */
+ { 14, SIGSEGV }, /* virtual instruction cache coherency */
+ { 15, SIGFPE }, /* floating point exception */
+ { 23, SIGSEGV }, /* watch */
+ { 31, SIGSEGV }, /* virtual data cache coherency */
+ { 0, 0} /* Must be last */
+};
+
+void arch_kgdb_breakpoint(void)
+{
+ __asm__ __volatile__(
+ ".globl breakinst\n\t"
+ ".set\tnoreorder\n\t"
+ "nop\n"
+ "breakinst:\tbreak\n\t"
+ "nop\n\t"
+ ".set\treorder");
+}
+
+static void kgdb_call_nmi_hook(void *ignored)
+{
+ kgdb_nmicallback(raw_smp_processor_id(), (void *)0);
+}
+
+void kgdb_roundup_cpus(unsigned long flags)
+{
+ local_irq_enable();
+ smp_call_function(kgdb_call_nmi_hook, NULL, NULL);
+ local_irq_disable();
+}
+
+static int compute_signal(int tt)
+{
+ struct hard_trap_info *ht;
+
+ for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
+ if (ht->tt == tt)
+ return ht->signo;
+
+ return SIGHUP; /* default for things we don't know about */
+}
+
+void pt_regs_to_gdb_regs(unsigned long *gdb_regs, struct pt_regs *regs)
+{
+ int reg;
+
+#if (KGDB_GDB_REG_SIZE == 32)
+ u32 *ptr = (u32 *)gdb_regs;
+#else
+ u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+ for (reg = 0; reg < 32; reg++)
+ *(ptr++) = regs->regs[reg];
+
+ *(ptr++) = regs->cp0_status;
+ *(ptr++) = regs->lo;
+ *(ptr++) = regs->hi;
+ *(ptr++) = regs->cp0_badvaddr;
+ *(ptr++) = regs->cp0_cause;
+ *(ptr++) = regs->cp0_epc;
+
+ /* FP REGS */
+ if (!(current && (regs->cp0_status & ST0_CU1)))
+ return;
+
+ save_fp(current);
+ for (reg = 0; reg < 32; reg++)
+ *(ptr++) = current->thread.fpu.fpr[reg];
+}
+
+void gdb_regs_to_pt_regs(unsigned long *gdb_regs, struct pt_regs *regs)
+{
+ int reg;
+
+#if (KGDB_GDB_REG_SIZE == 32)
+ const u32 *ptr = (u32 *)gdb_regs;
+#else
+ const u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+ for (reg = 0; reg < 32; reg++)
+ regs->regs[reg] = *(ptr++);
+
+ regs->cp0_status = *(ptr++);
+ regs->lo = *(ptr++);
+ regs->hi = *(ptr++);
+ regs->cp0_badvaddr = *(ptr++);
+ regs->cp0_cause = *(ptr++);
+ regs->cp0_epc = *(ptr++);
+
+ /* FP REGS from current */
+ if (!(current && (regs->cp0_status & ST0_CU1)))
+ return;
+
+ for (reg = 0; reg < 32; reg++)
+ current->thread.fpu.fpr[reg] = *(ptr++);
+ restore_fp(current);
+}
+
+/*
+ * Similar to regs_to_gdb_regs() except that process is sleeping and so
+ * we may not be able to get all the info.
+ */
+void sleeping_thread_to_gdb_regs(unsigned long *gdb_regs, struct task_struct *p)
+{
+ int reg;
+ struct thread_info *ti = task_thread_info(p);
+ unsigned long ksp = (unsigned long)ti + THREAD_SIZE - 32;
+ struct pt_regs *regs = (struct pt_regs *)ksp - 1;
+#if (KGDB_GDB_REG_SIZE == 32)
+ u32 *ptr = (u32 *)gdb_regs;
+#else
+ u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+ for (reg = 0; reg < 16; reg++)
+ *(ptr++) = regs->regs[reg];
+
+ /* S0 - S7 */
+ for (reg = 16; reg < 24; reg++)
+ *(ptr++) = regs->regs[reg];
+
+ for (reg = 24; reg < 28; reg++)
+ *(ptr++) = 0;
+
+ /* GP, SP, FP, RA */
+ for (reg = 28; reg < 32; reg++)
+ *(ptr++) = regs->regs[reg];
+
+ *(ptr++) = regs->cp0_status;
+ *(ptr++) = regs->lo;
+ *(ptr++) = regs->hi;
+ *(ptr++) = regs->cp0_badvaddr;
+ *(ptr++) = regs->cp0_cause;
+ *(ptr++) = regs->cp0_epc;
+}
+
+/*
+ * Calls linux_debug_hook before the kernel dies. If KGDB is enabled,
+ * then try to fall into the debugger
+ */
+static int kgdb_mips_notify(struct notifier_block *self, unsigned long cmd,
+ void *ptr)
+{
+ struct die_args *args = (struct die_args *)ptr;
+ struct pt_regs *regs = args->regs;
+ int trap = (regs->cp0_cause & 0x7c) >> 2;
+
+ if (fixup_exception(regs))
+ return NOTIFY_DONE;
+
+ /* Userpace events, ignore. */
+ if (user_mode(regs))
+ return NOTIFY_DONE;
+
+ if (atomic_read(&kgdb_active) != -1)
+ kgdb_nmicallback(smp_processor_id(), regs);
+
+ if (kgdb_handle_exception(trap, compute_signal(trap), 0, regs))
+ return NOTIFY_DONE;
+
+ if (atomic_read(&kgdb_setting_breakpoint))
+ if ((trap == 9) && (regs->cp0_epc == (unsigned long)breakinst))
+ regs->cp0_epc += 4;
+
+ /* In SMP mode, __flush_cache_all does IPI */
+ local_irq_enable();
+ __flush_cache_all();
+
+ return NOTIFY_STOP;
+}
+
+static struct notifier_block kgdb_notifier = {
+ .notifier_call = kgdb_mips_notify,
+};
+
+/*
+ * Handle the 's' and 'c' commands
+ */
+int kgdb_arch_handle_exception(int vector, int signo, int err_code,
+ char *remcom_in_buffer, char *remcom_out_buffer,
+ struct pt_regs *regs)
+{
+ char *ptr;
+ unsigned long address;
+ int cpu = smp_processor_id();
+
+ switch (remcom_in_buffer[0]) {
+ case 's':
+ case 'c':
+ /* handle the optional parameter */
+ ptr = &remcom_in_buffer[1];
+ if (kgdb_hex2long(&ptr, &address))
+ regs->cp0_epc = address;
+
+ atomic_set(&kgdb_cpu_doing_single_step, -1);
+ if (remcom_in_buffer[0] == 's')
+ if (kgdb_contthread)
+ atomic_set(&kgdb_cpu_doing_single_step, cpu);
+
+ return 0;
+ }
+
+ return -1;
+}
+
+struct kgdb_arch arch_kgdb_ops;
+
+/*
+ * We use kgdb_early_setup so that functions we need to call now don't
+ * cause trouble when called again later.
+ */
+int kgdb_arch_init(void)
+{
+ union mips_instruction insn = {
+ .r_format = {
+ .opcode = spec_op,
+ .func = break_op,
+ }
+ };
+ memcpy(arch_kgdb_ops.gdb_bpt_instr, insn.byte, BREAK_INSTR_SIZE);
+
+ register_die_notifier(&kgdb_notifier);
+
+ return 0;
+}
+
+/*
+ * kgdb_arch_exit - Perform any architecture specific uninitalization.
+ *
+ * This function will handle the uninitalization of any architecture
+ * specific callbacks, for dynamic registration and unregistration.
+ */
+void kgdb_arch_exit(void)
+{
+ unregister_die_notifier(&kgdb_notifier);
+}
#include <linux/bootmem.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
#include <asm/bootinfo.h>
#include <asm/branch.h>
printk(KERN_ALERT "%s bus error, epc == %0*lx, ra == %0*lx\n",
data ? "Data" : "Instruction",
field, regs->cp0_epc, field, regs->regs[31]);
+ if (notify_die(DIE_OOPS, "bus error", regs, SIGBUS, 0, 0)
+ == NOTIFY_STOP)
+ return;
+
die_if_kernel("Oops", regs);
force_sig(SIGBUS, current);
}
{
siginfo_t info;
+ if (notify_die(DIE_FP, "FP exception", regs, SIGFPE, 0, 0)
+ == NOTIFY_STOP)
+ return;
die_if_kernel("FP exception in kernel code", regs);
if (fcr31 & FPU_CSR_UNI_X) {
siginfo_t info;
char b[40];
+ if (notify_die(DIE_TRAP, str, regs, code, 0, 0) == NOTIFY_STOP)
+ return;
+
/*
* A short test says that IRIX 5.3 sends SIGTRAP for all trap
* insns, even for trap and break codes that indicate arithmetic
unsigned int opcode = 0;
int status = -1;
+ if (notify_die(DIE_RI, "RI Fault", regs, SIGSEGV, 0, 0)
+ == NOTIFY_STOP)
+ return;
+
die_if_kernel("Reserved instruction in kernel code", regs);
if (unlikely(compute_return_epc(regs) < 0))
extern char except_vec4;
unsigned long i;
+#if defined(CONFIG_KGDB)
+ if (kgdb_early_setup)
+ return; /* Already done */
+#endif
+
if (cpu_has_veic || cpu_has_vint)
ebase = (unsigned long) alloc_bootmem_low_pages(0x200 + VECTORSPACING*64);
else
old_pagemask = read_c0_pagemask();
w = read_c0_wired();
write_c0_wired(w + 1);
- if (read_c0_wired() != w + 1) {
- printk("[tlbwired] No WIRED reg?\n");
- return;
- }
write_c0_index(w << 8);
write_c0_pagemask(pagemask);
write_c0_entryhi(entryhi);
obj-$(CONFIG_EARLY_PRINTK) += malta-console.o
obj-$(CONFIG_PCI) += malta-pci.o
-obj-$(CONFIG_KGDB) += malta-kgdb.o
# FIXME FIXME FIXME
obj-$(CONFIG_MIPS_MT_SMTC) += malta_smtc.o
#include <asm/mips-boards/malta.h>
-#ifdef CONFIG_KGDB
-extern int rs_kgdb_hook(int, int);
-extern int rs_putDebugChar(char);
-extern char rs_getDebugChar(void);
-extern int saa9730_kgdb_hook(int);
-extern int saa9730_putDebugChar(char);
-extern char saa9730_getDebugChar(void);
-#endif
-
int prom_argc;
int *_prom_argv, *_prom_envp;
}
#endif
-#ifdef CONFIG_KGDB
-void __init kgdb_config(void)
-{
- extern int (*generic_putDebugChar)(char);
- extern char (*generic_getDebugChar)(void);
- char *argptr;
- int line, speed;
-
- argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
- argptr += strlen("kgdb=ttyS");
- if (*argptr != '0' && *argptr != '1')
- printk("KGDB: Unknown serial line /dev/ttyS%c, "
- "falling back to /dev/ttyS1\n", *argptr);
- line = *argptr == '0' ? 0 : 1;
- printk("KGDB: Using serial line /dev/ttyS%d for session\n", line);
-
- speed = 0;
- if (*++argptr == ',')
- {
- int c;
- while ((c = *++argptr) && ('0' <= c && c <= '9'))
- speed = speed * 10 + c - '0';
- }
- {
- speed = rs_kgdb_hook(line, speed);
- generic_putDebugChar = rs_putDebugChar;
- generic_getDebugChar = rs_getDebugChar;
- }
-
- pr_info("KGDB: Using serial line /dev/ttyS%d at %d for "
- "session, please connect your debugger\n",
- line ? 1 : 0, speed);
-
- {
- char *s;
- for (s = "Please connect GDB to this port\r\n"; *s; )
- generic_putDebugChar(*s++);
- }
-
- /* Breakpoint is invoked after interrupts are initialised */
- }
-}
-#endif
-
static void __init mips_nmi_setup(void)
{
void *base;
+++ /dev/null
-/*
- * Carsten Langgaard, carstenl@mips.com
- * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * This is the interface to the remote debugger stub.
- */
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/serial_reg.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-
-static struct serial_state rs_table[] = {
- SERIAL_PORT_DFNS /* Defined in serial.h */
-};
-
-static struct async_struct kdb_port_info = {0};
-
-int (*generic_putDebugChar)(char);
-char (*generic_getDebugChar)(void);
-
-static __inline__ unsigned int serial_in(struct async_struct *info, int offset)
-{
- return inb(info->port + offset);
-}
-
-static __inline__ void serial_out(struct async_struct *info, int offset,
- int value)
-{
- outb(value, info->port+offset);
-}
-
-int rs_kgdb_hook(int tty_no, int speed) {
- int t;
- struct serial_state *ser = &rs_table[tty_no];
-
- kdb_port_info.state = ser;
- kdb_port_info.magic = SERIAL_MAGIC;
- kdb_port_info.port = ser->port;
- kdb_port_info.flags = ser->flags;
-
- /*
- * Clear all interrupts
- */
- serial_in(&kdb_port_info, UART_LSR);
- serial_in(&kdb_port_info, UART_RX);
- serial_in(&kdb_port_info, UART_IIR);
- serial_in(&kdb_port_info, UART_MSR);
-
- /*
- * Now, initialize the UART
- */
- serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8); /* reset DLAB */
- if (kdb_port_info.flags & ASYNC_FOURPORT) {
- kdb_port_info.MCR = UART_MCR_DTR | UART_MCR_RTS;
- t = UART_MCR_DTR | UART_MCR_OUT1;
- } else {
- kdb_port_info.MCR
- = UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2;
- t = UART_MCR_DTR | UART_MCR_RTS;
- }
-
- kdb_port_info.MCR = t; /* no interrupts, please */
- serial_out(&kdb_port_info, UART_MCR, kdb_port_info.MCR);
-
- /*
- * and set the speed of the serial port
- */
- if (speed == 0)
- speed = 9600;
-
- t = kdb_port_info.state->baud_base / speed;
- /* set DLAB */
- serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8 | UART_LCR_DLAB);
- serial_out(&kdb_port_info, UART_DLL, t & 0xff);/* LS of divisor */
- serial_out(&kdb_port_info, UART_DLM, t >> 8); /* MS of divisor */
- /* reset DLAB */
- serial_out(&kdb_port_info, UART_LCR, UART_LCR_WLEN8);
-
- return speed;
-}
-
-int putDebugChar(char c)
-{
- return generic_putDebugChar(c);
-}
-
-char getDebugChar(void)
-{
- return generic_getDebugChar();
-}
-
-int rs_putDebugChar(char c)
-{
-
- if (!kdb_port_info.state) { /* need to init device first */
- return 0;
- }
-
- while ((serial_in(&kdb_port_info, UART_LSR) & UART_LSR_THRE) == 0)
- ;
-
- serial_out(&kdb_port_info, UART_TX, c);
-
- return 1;
-}
-
-char rs_getDebugChar(void)
-{
- if (!kdb_port_info.state) { /* need to init device first */
- return 0;
- }
-
- while (!(serial_in(&kdb_port_info, UART_LSR) & 1))
- ;
-
- return serial_in(&kdb_port_info, UART_RX);
-}
*/
enable_dma(4);
-#ifdef CONFIG_KGDB
- kgdb_config();
-#endif
-
#ifdef CONFIG_DMA_COHERENT
if (mips_revision_sconid != MIPS_REVISION_SCON_BONITO)
panic("Hardware DMA cache coherency not supported");
obj-y := setup.o prom.o int.o reset.o time.o proc.o platform.o
obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_KGDB) += gdb_hook.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- * Carsten Langgaard, carstenl@mips.com
- * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- * This is the interface to the remote debugger stub.
- *
- */
-#include <linux/types.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/serial_reg.h>
-#include <linux/serial_ip3106.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-
-#include <uart.h>
-
-static struct serial_state rs_table[IP3106_NR_PORTS] = {
-};
-static struct async_struct kdb_port_info = {0};
-
-void rs_kgdb_hook(int tty_no)
-{
- struct serial_state *ser = &rs_table[tty_no];
-
- kdb_port_info.state = ser;
- kdb_port_info.magic = SERIAL_MAGIC;
- kdb_port_info.port = tty_no;
- kdb_port_info.flags = ser->flags;
-
- /*
- * Clear all interrupts
- */
- /* Clear all the transmitter FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_TX_RST;
- /* Clear all the receiver FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, tty_no) |= IP3106_UART_LCR_RX_RST;
- /* Clear all interrupts */
- ip3106_iclr(UART_BASE, tty_no) = IP3106_UART_INT_ALLRX |
- IP3106_UART_INT_ALLTX;
-
- /*
- * Now, initialize the UART
- */
- ip3106_lcr(UART_BASE, tty_no) = IP3106_UART_LCR_8BIT;
- ip3106_baud(UART_BASE, tty_no) = 5; // 38400 Baud
-}
-
-int putDebugChar(char c)
-{
- /* Wait until FIFO not full */
- while (((ip3106_fifo(UART_BASE, kdb_port_info.port) & IP3106_UART_FIFO_TXFIFO) >> 16) >= 16)
- ;
- /* Send one char */
- ip3106_fifo(UART_BASE, kdb_port_info.port) = c;
-
- return 1;
-}
-
-char getDebugChar(void)
-{
- char ch;
-
- /* Wait until there is a char in the FIFO */
- while (!((ip3106_fifo(UART_BASE, kdb_port_info.port) &
- IP3106_UART_FIFO_RXFIFO) >> 8))
- ;
- /* Read one char */
- ch = ip3106_fifo(UART_BASE, kdb_port_info.port) &
- IP3106_UART_FIFO_RBRTHR;
- /* Advance the RX FIFO read pointer */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_NEXT;
- return (ch);
-}
-
-void rs_disable_debug_interrupts(void)
-{
- ip3106_ien(UART_BASE, kdb_port_info.port) = 0; /* Disable all interrupts */
-}
-
-void rs_enable_debug_interrupts(void)
-{
- /* Clear all the transmitter FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_TX_RST;
- /* Clear all the receiver FIFO counters (pointer and status) */
- ip3106_lcr(UART_BASE, kdb_port_info.port) |= IP3106_UART_LCR_RX_RST;
- /* Clear all interrupts */
- ip3106_iclr(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX |
- IP3106_UART_INT_ALLTX;
- ip3106_ien(UART_BASE, kdb_port_info.port) = IP3106_UART_INT_ALLRX; /* Enable RX interrupts */
-}
#include <linux/module.h>
#include <asm/io.h>
-#include <asm/gdb-stub.h>
#include <int.h>
#include <uart.h>
#include <linux/random.h>
#include <asm/io.h>
-#include <asm/gdb-stub.h>
#include <int.h>
#include <uart.h>
extern void pnx8550_machine_power_off(void);
extern struct resource ioport_resource;
extern struct resource iomem_resource;
-extern void rs_kgdb_hook(int tty_no);
extern char *prom_getcmdline(void);
struct resource standard_io_resources[] = {
ip3106_baud(UART_BASE, pnx8550_console_port) = 5;
}
-#ifdef CONFIG_KGDB
- argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "kgdb=ttyS")) != NULL) {
- int line;
- argptr += strlen("kgdb=ttyS");
- line = *argptr == '0' ? 0 : 1;
- rs_kgdb_hook(line);
- pr_info("KGDB: Using ttyS%i for session, "
- "please connect your debugger\n", line ? 1 : 0);
- }
-#endif
return;
}
#include <linux/pci.h>
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <asm/addrspace.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/pci.h>
#include <asm/txx9/tx3927.h>
-static inline int mkaddr(unsigned char bus, unsigned char dev_fn,
- unsigned char where)
+static int mkaddr(struct pci_bus *bus, unsigned char devfn, unsigned char where)
{
- if (bus == 0 && dev_fn >= PCI_DEVFN(TX3927_PCIC_MAX_DEVNU, 0))
- return PCIBIOS_DEVICE_NOT_FOUND;
-
- tx3927_pcicptr->ica = ((bus & 0xff) << 0x10) |
- ((dev_fn & 0xff) << 0x08) |
- (where & 0xfc);
+ if (bus->parent == NULL &&
+ devfn >= PCI_DEVFN(TX3927_PCIC_MAX_DEVNU, 0))
+ return -1;
+ tx3927_pcicptr->ica =
+ ((bus->number & 0xff) << 0x10) |
+ ((devfn & 0xff) << 0x08) |
+ (where & 0xfc) | (bus->parent ? 1 : 0);
/* clear M_ABORT and Disable M_ABORT Int. */
tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
tx3927_pcicptr->pcistatim &= ~PCI_STATUS_REC_MASTER_ABORT;
-
- return PCIBIOS_SUCCESSFUL;
+ return 0;
}
static inline int check_abort(void)
{
- if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT)
+ if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT) {
tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
tx3927_pcicptr->pcistatim |= PCI_STATUS_REC_MASTER_ABORT;
+ /* flush write buffer */
+ iob();
return PCIBIOS_DEVICE_NOT_FOUND;
-
+ }
return PCIBIOS_SUCCESSFUL;
}
static int tx3927_pci_read_config(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 * val)
{
- int ret;
-
- ret = mkaddr(bus->number, devfn, where);
- if (ret)
- return ret;
+ if (mkaddr(bus, devfn, where)) {
+ *val = 0xffffffff;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
switch (size) {
case 1:
static int tx3927_pci_write_config(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 val)
{
- int ret;
-
- ret = mkaddr(bus->number, devfn, where);
- if (ret)
- return ret;
+ if (mkaddr(bus, devfn, where))
+ return PCIBIOS_DEVICE_NOT_FOUND;
switch (size) {
case 1:
tx3927_pcicptr->icd = cpu_to_le32(val);
}
- if (tx3927_pcicptr->pcistat & PCI_STATUS_REC_MASTER_ABORT)
- tx3927_pcicptr->pcistat |= PCI_STATUS_REC_MASTER_ABORT;
- tx3927_pcicptr->pcistatim |= PCI_STATUS_REC_MASTER_ABORT;
- return PCIBIOS_DEVICE_NOT_FOUND;
-
return check_abort();
}
PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
local_irq_restore(flags);
}
+
+static irqreturn_t tx3927_pcierr_interrupt(int irq, void *dev_id)
+{
+ struct pt_regs *regs = get_irq_regs();
+
+ if (txx9_pci_err_action != TXX9_PCI_ERR_IGNORE) {
+ printk(KERN_WARNING "PCI error interrupt at 0x%08lx.\n",
+ regs->cp0_epc);
+ printk(KERN_WARNING "pcistat:%02x, lbstat:%04lx\n",
+ tx3927_pcicptr->pcistat, tx3927_pcicptr->lbstat);
+ }
+ if (txx9_pci_err_action != TXX9_PCI_ERR_PANIC) {
+ /* clear all pci errors */
+ tx3927_pcicptr->pcistat |= TX3927_PCIC_PCISTATIM_ALL;
+ tx3927_pcicptr->istat = TX3927_PCIC_IIM_ALL;
+ tx3927_pcicptr->tstat = TX3927_PCIC_TIM_ALL;
+ tx3927_pcicptr->lbstat = TX3927_PCIC_LBIM_ALL;
+ return IRQ_HANDLED;
+ }
+ console_verbose();
+ panic("PCI error.");
+}
+
+void __init tx3927_setup_pcierr_irq(void)
+{
+ if (request_irq(TXX9_IRQ_BASE + TX3927_IR_PCI,
+ tx3927_pcierr_interrupt,
+ IRQF_DISABLED, "PCI error",
+ (void *)TX3927_PCIC_REG))
+ printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}
* option) any later version.
*/
#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <asm/txx9/pci.h>
#include <asm/txx9/tx4927pcic.h>
static struct {
__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
| (PCI_STATUS_REC_MASTER_ABORT << 16),
&pcicptr->pcistatus);
+ /* flush write buffer */
+ iob();
code = PCIBIOS_DEVICE_NOT_FOUND;
}
return code;
.gbwc = 0xfe0, /* 4064 GBUSCLK for CCFG.GTOT=0b11 */
};
+char *__devinit tx4927_pcibios_setup(char *str)
+{
+ unsigned long val;
+
+ if (!strncmp(str, "trdyto=", 7)) {
+ if (strict_strtoul(str + 7, 0, &val) == 0)
+ tx4927_pci_opts.trdyto = val;
+ return NULL;
+ }
+ if (!strncmp(str, "retryto=", 8)) {
+ if (strict_strtoul(str + 8, 0, &val) == 0)
+ tx4927_pci_opts.retryto = val;
+ return NULL;
+ }
+ if (!strncmp(str, "gbwc=", 5)) {
+ if (strict_strtoul(str + 5, 0, &val) == 0)
+ tx4927_pci_opts.gbwc = val;
+ return NULL;
+ }
+ return str;
+}
+
void __init tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
struct pci_controller *channel, int extarb)
{
tx4927_report_pcic_status1(pcicptrs[i].pcicptr);
}
}
+
+static void tx4927_dump_pcic_settings1(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+ int i;
+ __u32 __iomem *preg = (__u32 __iomem *)pcicptr;
+
+ printk(KERN_INFO "tx4927 pcic (0x%p) settings:", pcicptr);
+ for (i = 0; i < sizeof(struct tx4927_pcic_reg); i += 4, preg++) {
+ if (i % 32 == 0) {
+ printk(KERN_CONT "\n");
+ printk(KERN_INFO "%04x:", i);
+ }
+ /* skip registers with side-effects */
+ if (i == offsetof(struct tx4927_pcic_reg, g2pintack)
+ || i == offsetof(struct tx4927_pcic_reg, g2pspc)
+ || i == offsetof(struct tx4927_pcic_reg, g2pcfgadrs)
+ || i == offsetof(struct tx4927_pcic_reg, g2pcfgdata)) {
+ printk(KERN_CONT " XXXXXXXX");
+ continue;
+ }
+ printk(KERN_CONT " %08x", __raw_readl(preg));
+ }
+ printk(KERN_CONT "\n");
+}
+
+void tx4927_dump_pcic_settings(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+ if (pcicptrs[i].pcicptr)
+ tx4927_dump_pcic_settings1(pcicptrs[i].pcicptr);
+ }
+}
+
+irqreturn_t tx4927_pcierr_interrupt(int irq, void *dev_id)
+{
+ struct pt_regs *regs = get_irq_regs();
+ struct tx4927_pcic_reg __iomem *pcicptr =
+ (struct tx4927_pcic_reg __iomem *)(unsigned long)dev_id;
+
+ if (txx9_pci_err_action != TXX9_PCI_ERR_IGNORE) {
+ printk(KERN_WARNING "PCIERR interrupt at 0x%0*lx\n",
+ (int)(2 * sizeof(unsigned long)), regs->cp0_epc);
+ tx4927_report_pcic_status1(pcicptr);
+ }
+ if (txx9_pci_err_action != TXX9_PCI_ERR_PANIC) {
+ /* clear all pci errors */
+ __raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+ | (TX4927_PCIC_PCISTATUS_ALL << 16),
+ &pcicptr->pcistatus);
+ __raw_writel(TX4927_PCIC_G2PSTATUS_ALL, &pcicptr->g2pstatus);
+ __raw_writel(TX4927_PCIC_PBASTATUS_ALL, &pcicptr->pbastatus);
+ __raw_writel(TX4927_PCIC_PCICSTATUS_ALL, &pcicptr->pcicstatus);
+ return IRQ_HANDLED;
+ }
+ console_verbose();
+ tx4927_dump_pcic_settings1(pcicptr);
+ panic("PCI error.");
+}
+
+#ifdef CONFIG_TOSHIBA_FPCIB0
+static void __init tx4927_quirk_slc90e66_bridge(struct pci_dev *dev)
+{
+ struct tx4927_pcic_reg __iomem *pcicptr = pci_bus_to_pcicptr(dev->bus);
+
+ if (!pcicptr)
+ return;
+ if (__raw_readl(&pcicptr->pbacfg) & TX4927_PCIC_PBACFG_PBAEN) {
+ /* Reset Bus Arbiter */
+ __raw_writel(TX4927_PCIC_PBACFG_RPBA, &pcicptr->pbacfg);
+ /*
+ * swap reqBP and reqXP (raise priority of SLC90E66).
+ * SLC90E66(PCI-ISA bridge) is connected to REQ2 on
+ * PCI Backplane board.
+ */
+ __raw_writel(0x72543610, &pcicptr->pbareqport);
+ __raw_writel(0, &pcicptr->pbabm);
+ /* Use Fixed ParkMaster (required by SLC90E66) */
+ __raw_writel(TX4927_PCIC_PBACFG_FIXPA, &pcicptr->pbacfg);
+ /* Enable Bus Arbiter */
+ __raw_writel(TX4927_PCIC_PBACFG_FIXPA |
+ TX4927_PCIC_PBACFG_PBAEN,
+ &pcicptr->pbacfg);
+ printk(KERN_INFO "PCI: Use Fixed Park Master (REQPORT %08x)\n",
+ __raw_readl(&pcicptr->pbareqport));
+ }
+}
+#define PCI_DEVICE_ID_EFAR_SLC90E66_0 0x9460
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_0,
+ tx4927_quirk_slc90e66_bridge);
+#endif
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/kernel.h>
+#include <linux/interrupt.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/tx4927.h>
pciclk = -1;
return pciclk;
}
+
+void __init tx4927_setup_pcierr_irq(void)
+{
+ if (request_irq(TXX9_IRQ_BASE + TX4927_IR_PCIERR,
+ tx4927_pcierr_interrupt,
+ IRQF_DISABLED, "PCI error",
+ (void *)TX4927_PCIC_REG))
+ printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/kernel.h>
+#include <linux/interrupt.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/tx4938.h>
}
return -1;
}
+
+void __init tx4938_setup_pcierr_irq(void)
+{
+ if (request_irq(TXX9_IRQ_BASE + TX4938_IR_PCIERR,
+ tx4927_pcierr_interrupt,
+ IRQF_DISABLED, "PCI error",
+ (void *)TX4927_PCIC_REG))
+ printk(KERN_WARNING "Failed to request irq for PCIERR\n");
+}
EXPORT_SYMBOL(PCIBIOS_MIN_MEM);
#endif
-char *pcibios_setup(char *str)
+char * (*pcibios_plat_setup)(char *str) __devinitdata;
+
+char *__devinit pcibios_setup(char *str)
{
+ if (pcibios_plat_setup)
+ return pcibios_plat_setup(str);
return str;
}
#include <msp_int.h>
#include <msp_regs.h>
-#ifdef CONFIG_KGDB
-/*
- * kgdb uses serial port 1 so the console can remain on port 0.
- * To use port 0 change the definition to read as follows:
- * #define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART0_BASE)
- */
-#define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART1_BASE)
-
-int putDebugChar(char c)
-{
- volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
- uint32_t val = (uint32_t)c;
-
- local_irq_disable();
- while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
- uart[0] = val;
- while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
- local_irq_enable();
-
- return 1;
-}
-
-char getDebugChar(void)
-{
- volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
- uint32_t val;
-
- while( !(uart[5] & 0x01) ); /* Wait for RXRDY */
- val = uart[0];
-
- return (char)val;
-}
-
-void initDebugPort(unsigned int uartclk, unsigned int baudrate)
-{
- unsigned int baud_divisor = (uartclk + 8 * baudrate)/(16 * baudrate);
-
- /* Enable FIFOs */
- writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
- UART_FCR_CLEAR_XMIT | UART_FCR_TRIGGER_4,
- (char *)DEBUG_PORT_BASE + (UART_FCR * 4));
-
- /* Select brtc divisor */
- writeb(UART_LCR_DLAB, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
-
- /* Store divisor lsb */
- writeb(baud_divisor, (char *)DEBUG_PORT_BASE + (UART_TX * 4));
-
- /* Store divisor msb */
- writeb(baud_divisor >> 8, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
-
- /* Set 8N1 mode */
- writeb(UART_LCR_WLEN8, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
-
- /* Disable flow control */
- writeb(0, (char *)DEBUG_PORT_BASE + (UART_MCR * 4));
-
- /* Disable receive interrupt(!) */
- writeb(0, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
-}
-#endif
-
void __init msp_serial_setup(void)
{
char *s;
case MACH_MSP7120_FPGA:
/* Enable UART1 on MSP4200 and MSP7120 */
*GPIO_CFG2_REG = 0x00002299;
-
-#ifdef CONFIG_KGDB
- /* Initialize UART1 for kgdb since PMON doesn't */
- if( DEBUG_PORT_BASE == KSEG1ADDR(MSP_UART1_BASE) ) {
- if( mips_machtype == MACH_MSP4200_FPGA
- || mips_machtype == MACH_MSP7120_FPGA )
- initDebugPort(uartclk, 19200);
- else
- initDebugPort(uartclk, 57600);
- }
-#endif
break;
default:
obj-y += irq.o prom.o py-console.o setup.o
-obj-$(CONFIG_KGDB) += dbg_io.o
obj-$(CONFIG_SMP) += smp.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- * Copyright 2003 PMC-Sierra
- * Author: Manish Lachwani (lachwani@pmc-sierra.com)
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-/*
- * Support for KGDB for the Yosemite board. We make use of single serial
- * port to be used for KGDB as well as console. The second serial port
- * seems to be having a problem. Single IRQ is allocated for both the
- * ports. Hence, the interrupt routing code needs to figure out whether
- * the interrupt came from channel A or B.
- */
-
-#include <asm/serial.h>
-
-/*
- * Baud rate, Parity, Data and Stop bit settings for the
- * serial port on the Yosemite. Note that the Early printk
- * patch has been added. So, we should be all set to go
- */
-#define YOSEMITE_BAUD_2400 2400
-#define YOSEMITE_BAUD_4800 4800
-#define YOSEMITE_BAUD_9600 9600
-#define YOSEMITE_BAUD_19200 19200
-#define YOSEMITE_BAUD_38400 38400
-#define YOSEMITE_BAUD_57600 57600
-#define YOSEMITE_BAUD_115200 115200
-
-#define YOSEMITE_PARITY_NONE 0
-#define YOSEMITE_PARITY_ODD 0x08
-#define YOSEMITE_PARITY_EVEN 0x18
-#define YOSEMITE_PARITY_MARK 0x28
-#define YOSEMITE_PARITY_SPACE 0x38
-
-#define YOSEMITE_DATA_5BIT 0x0
-#define YOSEMITE_DATA_6BIT 0x1
-#define YOSEMITE_DATA_7BIT 0x2
-#define YOSEMITE_DATA_8BIT 0x3
-
-#define YOSEMITE_STOP_1BIT 0x0
-#define YOSEMITE_STOP_2BIT 0x4
-
-/* This is crucial */
-#define SERIAL_REG_OFS 0x1
-
-#define SERIAL_RCV_BUFFER 0x0
-#define SERIAL_TRANS_HOLD 0x0
-#define SERIAL_SEND_BUFFER 0x0
-#define SERIAL_INTR_ENABLE (1 * SERIAL_REG_OFS)
-#define SERIAL_INTR_ID (2 * SERIAL_REG_OFS)
-#define SERIAL_DATA_FORMAT (3 * SERIAL_REG_OFS)
-#define SERIAL_LINE_CONTROL (3 * SERIAL_REG_OFS)
-#define SERIAL_MODEM_CONTROL (4 * SERIAL_REG_OFS)
-#define SERIAL_RS232_OUTPUT (4 * SERIAL_REG_OFS)
-#define SERIAL_LINE_STATUS (5 * SERIAL_REG_OFS)
-#define SERIAL_MODEM_STATUS (6 * SERIAL_REG_OFS)
-#define SERIAL_RS232_INPUT (6 * SERIAL_REG_OFS)
-#define SERIAL_SCRATCH_PAD (7 * SERIAL_REG_OFS)
-
-#define SERIAL_DIVISOR_LSB (0 * SERIAL_REG_OFS)
-#define SERIAL_DIVISOR_MSB (1 * SERIAL_REG_OFS)
-
-/*
- * Functions to READ and WRITE to serial port 0
- */
-#define SERIAL_READ(ofs) (*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE + ofs)))
-
-#define SERIAL_WRITE(ofs, val) ((*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE + ofs))) = val)
-
-/*
- * Functions to READ and WRITE to serial port 1
- */
-#define SERIAL_READ_1(ofs) (*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE_1 + ofs)))
-
-#define SERIAL_WRITE_1(ofs, val) ((*((volatile unsigned char*) \
- (TITAN_SERIAL_BASE_1 + ofs))) = val)
-
-/*
- * Second serial port initialization
- */
-void init_second_port(void)
-{
- /* Disable Interrupts */
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
- SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0x0);
-
- {
- unsigned int divisor;
-
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x80);
- divisor = TITAN_SERIAL_BASE_BAUD / YOSEMITE_BAUD_115200;
- SERIAL_WRITE_1(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
- SERIAL_WRITE_1(SERIAL_DIVISOR_MSB,
- (divisor & 0xff00) >> 8);
- SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
- }
-
- SERIAL_WRITE_1(SERIAL_DATA_FORMAT, YOSEMITE_DATA_8BIT |
- YOSEMITE_PARITY_NONE | YOSEMITE_STOP_1BIT);
-
- /* Enable Interrupts */
- SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0xf);
-}
-
-/* Initialize the serial port for KGDB debugging */
-void debugInit(unsigned int baud, unsigned char data, unsigned char parity,
- unsigned char stop)
-{
- /* Disable Interrupts */
- SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
- SERIAL_WRITE(SERIAL_INTR_ENABLE, 0x0);
-
- {
- unsigned int divisor;
-
- SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x80);
-
- divisor = TITAN_SERIAL_BASE_BAUD / baud;
- SERIAL_WRITE(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
- SERIAL_WRITE(SERIAL_DIVISOR_MSB, (divisor & 0xff00) >> 8);
- SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
- }
-
- SERIAL_WRITE(SERIAL_DATA_FORMAT, data | parity | stop);
-}
-
-static int remoteDebugInitialized = 0;
-
-unsigned char getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(YOSEMITE_BAUD_115200,
- YOSEMITE_DATA_8BIT,
- YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
- }
-
- while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x1) == 0);
- return SERIAL_READ(SERIAL_RCV_BUFFER);
-}
-
-int putDebugChar(unsigned char byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(YOSEMITE_BAUD_115200,
- YOSEMITE_DATA_8BIT,
- YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
- }
-
- while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x20) == 0);
- SERIAL_WRITE(SERIAL_SEND_BUFFER, byte);
-
- return 1;
-}
}
}
-#ifdef CONFIG_KGDB
-extern void init_second_port(void);
-#endif
-
/*
* Initialize the next level interrupt handler
*/
rm7k_cpu_irq_init();
rm9k_cpu_irq_init();
-#ifdef CONFIG_KGDB
- /* At this point, initialize the second serial port */
- init_second_port();
-#endif
-
#ifdef CONFIG_GDB_CONSOLE
register_gdb_console();
#endif
void set_434_reg(unsigned reg_offs, unsigned bit, unsigned len, unsigned val)
{
- unsigned flags, data;
+ unsigned long flags;
+ unsigned data;
unsigned i = 0;
spin_lock_irqsave(&dev3.lock, flags);
void set_latch_u5(unsigned char or_mask, unsigned char nand_mask)
{
- unsigned flags;
+ unsigned long flags;
spin_lock_irqsave(&dev3.lock, flags);
void __init plat_time_init(void)
{
- unsigned int est_freq, flags;
- unsigned long r4k_offset;
+ unsigned int est_freq;
+ unsigned long flags, r4k_offset;
local_irq_save(flags);
#include <asm/irq.h>
#include <asm/reboot.h>
#include <asm/time.h>
-#include <asm/gdb-stub.h>
#include <asm/io.h>
#include <asm/traps.h>
#include <asm/sgialib.h>
add_preferred_console("arc", 0, NULL);
}
-#ifdef CONFIG_KGDB
- {
- char *kgdb_ttyd = prom_getcmdline();
-
- if ((kgdb_ttyd = strstr(kgdb_ttyd, "kgdb=ttyd")) != NULL) {
- int line;
- kgdb_ttyd += strlen("kgdb=ttyd");
- if (*kgdb_ttyd != '1' && *kgdb_ttyd != '2')
- printk(KERN_INFO "KGDB: Uknown serial line /dev/ttyd%c"
- ", falling back to /dev/ttyd1\n", *kgdb_ttyd);
- line = *kgdb_ttyd == '2' ? 0 : 1;
- printk(KERN_INFO "KGDB: Using serial line /dev/ttyd%d for "
- "session\n", line ? 1 : 2);
- rs_kgdb_hook(line);
-
- printk(KERN_INFO "KGDB: Using serial line /dev/ttyd%d for "
- "session, please connect your debugger\n", line ? 1:2);
-
- kgdb_enabled = 1;
- /* Breakpoints and stuff are in sgi_irq_setup() */
- }
- }
-#endif
-
#if defined(CONFIG_VT) && defined(CONFIG_SGI_NEWPORT_CONSOLE)
{
ULONG *gfxinfo;
ip27-xtalk.o
obj-$(CONFIG_EARLY_PRINTK) += ip27-console.o
-obj-$(CONFIG_KGDB) += ip27-dbgio.o
obj-$(CONFIG_SMP) += ip27-smp.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Copyright 2004 Ralf Baechle <ralf@linux-mips.org>
- */
-#include <asm/sn/addrs.h>
-#include <asm/sn/sn0/hub.h>
-#include <asm/sn/klconfig.h>
-#include <asm/sn/ioc3.h>
-#include <asm/sn/sn_private.h>
-
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-#include <linux/serial_reg.h>
-
-#define IOC3_CLK (22000000 / 3)
-#define IOC3_FLAGS (0)
-
-static inline struct ioc3_uartregs *console_uart(void)
-{
- struct ioc3 *ioc3;
-
- ioc3 = (struct ioc3 *)KL_CONFIG_CH_CONS_INFO(get_nasid())->memory_base;
-
- return &ioc3->sregs.uarta;
-}
-
-unsigned char getDebugChar(void)
-{
- struct ioc3_uartregs *uart = console_uart();
-
- while ((uart->iu_lsr & UART_LSR_DR) == 0);
- return uart->iu_rbr;
-}
-
-void putDebugChar(unsigned char c)
-{
- struct ioc3_uartregs *uart = console_uart();
-
- while ((uart->iu_lsr & UART_LSR_THRE) == 0);
- uart->iu_thr = c;
-}
extern unsigned long ht_eoi_space;
#endif
-#ifdef CONFIG_KGDB
-#include <asm/gdb-stub.h>
-extern void breakpoint(void);
-static int kgdb_irq;
-#ifdef CONFIG_GDB_CONSOLE
-extern void register_gdb_console(void);
-#endif
-
-/* kgdb is on when configured. Pass "nokgdb" kernel arg to turn it off */
-static int kgdb_flag = 1;
-static int __init nokgdb(char *str)
-{
- kgdb_flag = 0;
- return 1;
-}
-__setup("nokgdb", nokgdb);
-
-/* Default to UART1 */
-int kgdb_port = 1;
-#ifdef CONFIG_SERIAL_SB1250_DUART
-extern char sb1250_duart_present[];
-#endif
-#endif
-
static struct irq_chip bcm1480_irq_type = {
.name = "BCM1480-IMR",
.ack = ack_bcm1480_irq,
* does its own management of IP7.
*/
-#ifdef CONFIG_KGDB
- imask |= STATUSF_IP6;
-#endif
/* Enable necessary IPs, disable the rest */
change_c0_status(ST0_IM, imask);
-
-#ifdef CONFIG_KGDB
- if (kgdb_flag) {
- kgdb_irq = K_BCM1480_INT_UART_0 + kgdb_port;
-
-#ifdef CONFIG_SERIAL_SB1250_DUART
- sb1250_duart_present[kgdb_port] = 0;
-#endif
- /* Setup uart 1 settings, mapper */
- /* QQQ FIXME */
- __raw_writeq(M_DUART_IMR_BRK, IOADDR(A_DUART_IMRREG(kgdb_port)));
-
- __raw_writeq(IMR_IP6_VAL,
- IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
- (kgdb_irq << 3)));
- bcm1480_unmask_irq(0, kgdb_irq);
-
-#ifdef CONFIG_GDB_CONSOLE
- register_gdb_console();
-#endif
- printk("Waiting for GDB on UART port %d\n", kgdb_port);
- set_debug_traps();
- breakpoint();
- }
-#endif
-}
-
-#ifdef CONFIG_KGDB
-
-#include <linux/delay.h>
-
-#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-static void bcm1480_kgdb_interrupt(void)
-{
- /*
- * Clear break-change status (allow some time for the remote
- * host to stop the break, since we would see another
- * interrupt on the end-of-break too)
- */
- kstat.irqs[smp_processor_id()][kgdb_irq]++;
- mdelay(500);
- duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT |
- M_DUART_RX_EN | M_DUART_TX_EN);
- set_async_breakpoint(&get_irq_regs()->cp0_epc);
}
-#endif /* CONFIG_KGDB */
-
extern void bcm1480_mailbox_interrupt(void);
static inline void dispatch_ip2(void)
bcm1480_mailbox_interrupt();
#endif
-#ifdef CONFIG_KGDB
- else if (pending & CAUSEF_IP6)
- bcm1480_kgdb_interrupt(); /* KGDB (uart 1) */
-#endif
-
else if (pending & CAUSEF_IP2)
dispatch_ip2();
}
extern unsigned long initrd_start, initrd_end;
#endif
-#ifdef CONFIG_KGDB
-extern int kgdb_port;
-#endif
-
static void __noreturn cfe_linux_exit(void *arg)
{
int warm = *(int *)arg;
int argc = fw_arg0;
char **envp = (char **) fw_arg2;
int *prom_vec = (int *) fw_arg3;
-#ifdef CONFIG_KGDB
- char *arg;
-#endif
_machine_restart = cfe_linux_restart;
_machine_halt = cfe_linux_halt;
}
}
-#ifdef CONFIG_KGDB
- if ((arg = strstr(arcs_cmdline, "kgdb=duart")) != NULL)
- kgdb_port = (arg[10] == '0') ? 0 : 1;
- else
- kgdb_port = 1;
-#endif
-
#ifdef CONFIG_BLK_DEV_INITRD
{
char *ptr;
extern unsigned long ldt_eoi_space;
#endif
-#ifdef CONFIG_KGDB
-static int kgdb_irq;
-
-/* Default to UART1 */
-int kgdb_port = 1;
-#ifdef CONFIG_SERIAL_SB1250_DUART
-extern char sb1250_duart_present[];
-#endif
-#endif
-
static struct irq_chip sb1250_irq_type = {
.name = "SB1250-IMR",
.ack = ack_sb1250_irq,
* does its own management of IP7.
*/
-#ifdef CONFIG_KGDB
- imask |= STATUSF_IP6;
-#endif
/* Enable necessary IPs, disable the rest */
change_c0_status(ST0_IM, imask);
-
-#ifdef CONFIG_KGDB
- if (kgdb_flag) {
- kgdb_irq = K_INT_UART_0 + kgdb_port;
-
-#ifdef CONFIG_SERIAL_SB1250_DUART
- sb1250_duart_present[kgdb_port] = 0;
-#endif
- /* Setup uart 1 settings, mapper */
- __raw_writeq(M_DUART_IMR_BRK,
- IOADDR(A_DUART_IMRREG(kgdb_port)));
-
- __raw_writeq(IMR_IP6_VAL,
- IOADDR(A_IMR_REGISTER(0,
- R_IMR_INTERRUPT_MAP_BASE) +
- (kgdb_irq << 3)));
- sb1250_unmask_irq(0, kgdb_irq);
- }
-#endif
-}
-
-#ifdef CONFIG_KGDB
-
-#include <linux/delay.h>
-
-#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-static void sb1250_kgdb_interrupt(void)
-{
- /*
- * Clear break-change status (allow some time for the remote
- * host to stop the break, since we would see another
- * interrupt on the end-of-break too)
- */
- kstat_this_cpu.irqs[kgdb_irq]++;
- mdelay(500);
- duart_out(R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT |
- M_DUART_RX_EN | M_DUART_TX_EN);
- set_async_breakpoint(&get_irq_regs()->cp0_epc);
}
-#endif /* CONFIG_KGDB */
-
extern void sb1250_mailbox_interrupt(void);
static inline void dispatch_ip2(void)
sb1250_mailbox_interrupt();
#endif
-#ifdef CONFIG_KGDB
- else if (pending & CAUSEF_IP6) /* KGDB (uart 1) */
- sb1250_kgdb_interrupt();
-#endif
-
else if (pending & CAUSEF_IP2)
dispatch_ip2();
else
obj-y := setup.o rtc_xicor1241.o rtc_m41t81.o
obj-$(CONFIG_I2C_BOARDINFO) += swarm-i2c.o
-obj-$(CONFIG_KGDB) += dbg_io.o
+++ /dev/null
-/*
- * kgdb debug routines for SiByte boards.
- *
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-/* -------------------- BEGINNING OF CONFIG --------------------- */
-
-#include <linux/delay.h>
-#include <asm/io.h>
-#include <asm/sibyte/sb1250.h>
-#include <asm/sibyte/sb1250_regs.h>
-#include <asm/sibyte/sb1250_uart.h>
-#include <asm/sibyte/sb1250_int.h>
-#include <asm/addrspace.h>
-
-/*
- * We use the second serial port for kgdb traffic.
- * 115200, 8, N, 1.
- */
-
-#define BAUD_RATE 115200
-#define CLK_DIVISOR V_DUART_BAUD_RATE(BAUD_RATE)
-#define DATA_BITS V_DUART_BITS_PER_CHAR_8 /* or 7 */
-#define PARITY V_DUART_PARITY_MODE_NONE /* or even */
-#define STOP_BITS M_DUART_STOP_BIT_LEN_1 /* or 2 */
-
-static int duart_initialized = 0; /* 0: need to be init'ed by kgdb */
-
-/* -------------------- END OF CONFIG --------------------- */
-extern int kgdb_port;
-
-#define duart_out(reg, val) csr_out32(val, IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-#define duart_in(reg) csr_in32(IOADDR(A_DUART_CHANREG(kgdb_port, reg)))
-
-void putDebugChar(unsigned char c);
-unsigned char getDebugChar(void);
-static void
-duart_init(int clk_divisor, int data, int parity, int stop)
-{
- duart_out(R_DUART_MODE_REG_1, data | parity);
- duart_out(R_DUART_MODE_REG_2, stop);
- duart_out(R_DUART_CLK_SEL, clk_divisor);
-
- duart_out(R_DUART_CMD, M_DUART_RX_EN | M_DUART_TX_EN); /* enable rx and tx */
-}
-
-void
-putDebugChar(unsigned char c)
-{
- if (!duart_initialized) {
- duart_initialized = 1;
- duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS);
- }
- while ((duart_in(R_DUART_STATUS) & M_DUART_TX_RDY) == 0);
- duart_out(R_DUART_TX_HOLD, c);
-}
-
-unsigned char
-getDebugChar(void)
-{
- if (!duart_initialized) {
- duart_initialized = 1;
- duart_init(CLK_DIVISOR, DATA_BITS, PARITY, STOP_BITS);
- }
- while ((duart_in(R_DUART_STATUS) & M_DUART_RX_RDY) == 0) ;
- return duart_in(R_DUART_RX_HOLD);
-}
-
+config MACH_TX39XX
+ bool
+ select MACH_TXX9
+ select SYS_HAS_CPU_TX39XX
+
+config MACH_TX49XX
+ bool
+ select MACH_TXX9
+ select CEVT_R4K
+ select CSRC_R4K
+ select IRQ_CPU
+ select SYS_HAS_CPU_TX49XX
+ select SYS_SUPPORTS_64BIT_KERNEL
+
+config MACH_TXX9
+ bool
+ select DMA_NONCOHERENT
+ select SWAP_IO_SPACE
+ select SYS_HAS_EARLY_PRINTK
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select GENERIC_HARDIRQS_NO__DO_IRQ
+
config TOSHIBA_JMR3927
bool "Toshiba JMR-TX3927 board"
depends on MACH_TX39XX
config SOC_TX3927
bool
select CEVT_TXX9
- select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
select HW_HAS_PCI
select IRQ_TXX9
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX39XX
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select GENERIC_HARDIRQS_NO__DO_IRQ
select GPIO_TXX9
config SOC_TX4927
bool
- select CEVT_R4K
- select CSRC_R4K
select CEVT_TXX9
- select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
select HW_HAS_PCI
- select IRQ_CPU
select IRQ_TXX9
select PCI_TX4927
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX49XX
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
- select GENERIC_HARDIRQS_NO__DO_IRQ
select GPIO_TXX9
config SOC_TX4938
bool
- select CEVT_R4K
- select CSRC_R4K
select CEVT_TXX9
- select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
select HW_HAS_PCI
- select IRQ_CPU
select IRQ_TXX9
select PCI_TX4927
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX49XX
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
- select GENERIC_HARDIRQS_NO__DO_IRQ
select GPIO_TXX9
config TOSHIBA_FPCIB0
bool "FPCIB0 Backplane Support"
- depends on PCI && (MACH_TX39XX || MACH_TX49XX)
+ depends on PCI && MACH_TXX9
select I8259
config PICMG_PCI_BACKPLANE_DEFAULT
bool "Support for PICMG PCI Backplane"
- depends on PCI && (MACH_TX39XX || MACH_TX49XX)
+ depends on PCI && MACH_TXX9
default y if !TOSHIBA_FPCIB0
if TOSHIBA_RBTX4938
obj-y += setup.o
obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_SOC_TX3927) += setup_tx3927.o irq_tx3927.o
obj-$(CONFIG_SOC_TX4927) += mem_tx4927.o setup_tx4927.o irq_tx4927.o
obj-$(CONFIG_SOC_TX4938) += mem_tx4927.o setup_tx4938.o irq_tx4938.o
obj-$(CONFIG_TOSHIBA_FPCIB0) += smsc_fdc37m81x.o
-obj-$(CONFIG_KGDB) += dbgio.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-/*
- * linux/arch/mips/tx4938/common/dbgio.c
- *
- * kgdb interface for gdb
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
- * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
- * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
- * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
- * TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
- * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Support for TX4938 in 2.6 - Hiroshi DOYU <Hiroshi_DOYU@montavista.co.jp>
- */
-
-#include <linux/types>
-
-extern u8 txx9_sio_kdbg_rd(void);
-extern int txx9_sio_kdbg_wr( u8 ch );
-
-u8 getDebugChar(void)
-{
- return (txx9_sio_kdbg_rd());
-}
-
-int putDebugChar(u8 byte)
-{
- return (txx9_sio_kdbg_wr(byte));
-}
-
--- /dev/null
+/*
+ * Common tx3927 irq handler
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ */
+#include <linux/init.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/tx3927.h>
+
+void __init tx3927_irq_init(void)
+{
+ int i;
+
+ txx9_irq_init(TX3927_IRC_REG);
+ /* raise priority for timers, sio */
+ for (i = 0; i < TX3927_NR_TMR; i++)
+ txx9_irq_set_pri(TX3927_IR_TMR(i), 6);
+ for (i = 0; i < TX3927_NR_SIO; i++)
+ txx9_irq_set_pri(TX3927_IR_SIO(i), 7);
+}
{
return txx9_board_vec->pci_map_irq(dev, slot, pin);
}
+
+char * (*txx9_board_pcibios_setup)(char *str) __devinitdata;
+
+char *__devinit txx9_pcibios_setup(char *str)
+{
+ if (txx9_board_pcibios_setup && !txx9_board_pcibios_setup(str))
+ return NULL;
+ if (!strcmp(str, "picmg")) {
+ /* PICMG compliant backplane (TOSHIBA JMB-PICMG-ATX
+ (5V or 3.3V), JMB-PICMG-L2 (5V only), etc.) */
+ txx9_pci_option |= TXX9_PCI_OPT_PICMG;
+ return NULL;
+ } else if (!strcmp(str, "nopicmg")) {
+ /* non-PICMG compliant backplane (TOSHIBA
+ RBHBK4100,RBHBK4200, Interface PCM-PCM05, etc.) */
+ txx9_pci_option &= ~TXX9_PCI_OPT_PICMG;
+ return NULL;
+ } else if (!strncmp(str, "clk=", 4)) {
+ char *val = str + 4;
+ txx9_pci_option &= ~TXX9_PCI_OPT_CLK_MASK;
+ if (strcmp(val, "33") == 0)
+ txx9_pci_option |= TXX9_PCI_OPT_CLK_33;
+ else if (strcmp(val, "66") == 0)
+ txx9_pci_option |= TXX9_PCI_OPT_CLK_66;
+ else /* "auto" */
+ txx9_pci_option |= TXX9_PCI_OPT_CLK_AUTO;
+ return NULL;
+ } else if (!strncmp(str, "err=", 4)) {
+ if (!strcmp(str + 4, "panic"))
+ txx9_pci_err_action = TXX9_PCI_ERR_PANIC;
+ else if (!strcmp(str + 4, "ignore"))
+ txx9_pci_err_action = TXX9_PCI_ERR_IGNORE;
+ return NULL;
+ }
+ return str;
+}
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
#include <asm/bootinfo.h>
#include <asm/time.h>
+#include <asm/reboot.h>
#include <asm/txx9/generic.h>
+#include <asm/txx9/pci.h>
#ifdef CONFIG_CPU_TX49XX
#include <asm/txx9/tx4938.h>
#endif
return &(arcs_cmdline[0]);
}
+static void __noreturn txx9_machine_halt(void)
+{
+ local_irq_disable();
+ clear_c0_status(ST0_IM);
+ while (1) {
+ if (cpu_wait) {
+ (*cpu_wait)();
+ if (cpu_has_counter) {
+ /*
+ * Clear counter interrupt while it
+ * breaks WAIT instruction even if
+ * masked.
+ */
+ write_c0_compare(0);
+ }
+ }
+ }
+}
+
+/* Watchdog support */
+void __init txx9_wdt_init(unsigned long base)
+{
+ struct resource res = {
+ .start = base,
+ .end = base + 0x100 - 1,
+ .flags = IORESOURCE_MEM,
+ };
+ platform_device_register_simple("txx9wdt", -1, &res, 1);
+}
+
+/* SPI support */
+void __init txx9_spi_init(int busid, unsigned long base, int irq)
+{
+ struct resource res[] = {
+ {
+ .start = base,
+ .end = base + 0x20 - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = irq,
+ .flags = IORESOURCE_IRQ,
+ },
+ };
+ platform_device_register_simple("spi_txx9", busid,
+ res, ARRAY_SIZE(res));
+}
+
+void __init txx9_ethaddr_init(unsigned int id, unsigned char *ethaddr)
+{
+ struct platform_device *pdev =
+ platform_device_alloc("tc35815-mac", id);
+ if (!pdev ||
+ platform_device_add_data(pdev, ethaddr, 6) ||
+ platform_device_add(pdev))
+ platform_device_put(pdev);
+}
+
+void __init txx9_sio_init(unsigned long baseaddr, int irq,
+ unsigned int line, unsigned int sclk, int nocts)
+{
+#ifdef CONFIG_SERIAL_TXX9
+ struct uart_port req;
+
+ memset(&req, 0, sizeof(req));
+ req.line = line;
+ req.iotype = UPIO_MEM;
+ req.membase = ioremap(baseaddr, 0x24);
+ req.mapbase = baseaddr;
+ req.irq = irq;
+ if (!nocts)
+ req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
+ if (sclk) {
+ req.flags |= UPF_MAGIC_MULTIPLIER /*USE_SCLK*/;
+ req.uartclk = sclk;
+ } else
+ req.uartclk = TXX9_IMCLK;
+ early_serial_txx9_setup(&req);
+#endif /* CONFIG_SERIAL_TXX9 */
+}
+
+#ifdef CONFIG_EARLY_PRINTK
+static void __init null_prom_putchar(char c)
+{
+}
+void (*txx9_prom_putchar)(char c) __initdata = null_prom_putchar;
+
+void __init prom_putchar(char c)
+{
+ txx9_prom_putchar(c);
+}
+
+static void __iomem *early_txx9_sio_port;
+
+static void __init early_txx9_sio_putchar(char c)
+{
+#define TXX9_SICISR 0x0c
+#define TXX9_SITFIFO 0x1c
+#define TXX9_SICISR_TXALS 0x00000002
+ while (!(__raw_readl(early_txx9_sio_port + TXX9_SICISR) &
+ TXX9_SICISR_TXALS))
+ ;
+ __raw_writel(c, early_txx9_sio_port + TXX9_SITFIFO);
+}
+
+void __init txx9_sio_putchar_init(unsigned long baseaddr)
+{
+ early_txx9_sio_port = ioremap(baseaddr, 0x24);
+ txx9_prom_putchar = early_txx9_sio_putchar;
+}
+#endif /* CONFIG_EARLY_PRINTK */
+
/* wrappers */
void __init plat_mem_setup(void)
{
ioport_resource.end = ~0UL; /* no limit */
iomem_resource.start = 0;
iomem_resource.end = ~0UL; /* no limit */
+
+ /* fallback restart/halt routines */
+ _machine_restart = (void (*)(char *))txx9_machine_halt;
+ _machine_halt = txx9_machine_halt;
+ pm_power_off = txx9_machine_halt;
+
+#ifdef CONFIG_PCI
+ pcibios_plat_setup = txx9_pcibios_setup;
+#endif
txx9_board_vec->mem_setup();
}
--- /dev/null
+/*
+ * TX3927 setup routines
+ * Based on linux/arch/mips/txx9/jmr3927/setup.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/param.h>
+#include <linux/io.h>
+#include <asm/mipsregs.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9tmr.h>
+#include <asm/txx9pio.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/tx3927.h>
+
+void __init tx3927_wdt_init(void)
+{
+ txx9_wdt_init(TX3927_TMR_REG(2));
+}
+
+void __init tx3927_setup(void)
+{
+ int i;
+ unsigned int conf;
+
+ /* don't enable - see errata */
+ txx9_ccfg_toeon = 0;
+ if (strstr(prom_getcmdline(), "toeon") != NULL)
+ txx9_ccfg_toeon = 1;
+
+ txx9_reg_res_init(TX3927_REV_PCODE(), TX3927_REG_BASE,
+ TX3927_REG_SIZE);
+
+ /* SDRAMC,ROMC are configured by PROM */
+ for (i = 0; i < 8; i++) {
+ if (!(tx3927_romcptr->cr[i] & 0x8))
+ continue; /* disabled */
+ txx9_ce_res[i].start = (unsigned long)TX3927_ROMC_BA(i);
+ txx9_ce_res[i].end =
+ txx9_ce_res[i].start + TX3927_ROMC_SIZE(i) - 1;
+ request_resource(&iomem_resource, &txx9_ce_res[i]);
+ }
+
+ /* clocks */
+ txx9_gbus_clock = txx9_cpu_clock / 2;
+ /* change default value to udelay/mdelay take reasonable time */
+ loops_per_jiffy = txx9_cpu_clock / HZ / 2;
+
+ /* CCFG */
+ /* enable Timeout BusError */
+ if (txx9_ccfg_toeon)
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_TOE;
+
+ /* clear BusErrorOnWrite flag */
+ tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_BEOW;
+ if (read_c0_conf() & TX39_CONF_WBON)
+ /* Disable PCI snoop */
+ tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_PSNP;
+ else
+ /* Enable PCI SNOOP - with write through only */
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_PSNP;
+ /* do reset on watchdog */
+ tx3927_ccfgptr->ccfg |= TX3927_CCFG_WR;
+
+ printk(KERN_INFO "TX3927 -- CRIR:%08lx CCFG:%08lx PCFG:%08lx\n",
+ tx3927_ccfgptr->crir,
+ tx3927_ccfgptr->ccfg, tx3927_ccfgptr->pcfg);
+
+ /* TMR */
+ for (i = 0; i < TX3927_NR_TMR; i++)
+ txx9_tmr_init(TX3927_TMR_REG(i));
+
+ /* DMA */
+ tx3927_dmaptr->mcr = 0;
+ for (i = 0; i < ARRAY_SIZE(tx3927_dmaptr->ch); i++) {
+ /* reset channel */
+ tx3927_dmaptr->ch[i].ccr = TX3927_DMA_CCR_CHRST;
+ tx3927_dmaptr->ch[i].ccr = 0;
+ }
+ /* enable DMA */
+#ifdef __BIG_ENDIAN
+ tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN;
+#else
+ tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN | TX3927_DMA_MCR_LE;
+#endif
+
+ /* PIO */
+ __raw_writel(0, &tx3927_pioptr->maskcpu);
+ __raw_writel(0, &tx3927_pioptr->maskext);
+ txx9_gpio_init(TX3927_PIO_REG, 0, 16);
+
+ conf = read_c0_conf();
+ if (!(conf & TX39_CONF_ICE))
+ printk(KERN_INFO "TX3927 I-Cache disabled.\n");
+ if (!(conf & TX39_CONF_DCE))
+ printk(KERN_INFO "TX3927 D-Cache disabled.\n");
+ else if (!(conf & TX39_CONF_WBON))
+ printk(KERN_INFO "TX3927 D-Cache WriteThrough.\n");
+ else if (!(conf & TX39_CONF_CWFON))
+ printk(KERN_INFO "TX3927 D-Cache WriteBack.\n");
+ else
+ printk(KERN_INFO "TX3927 D-Cache WriteBack (CWF) .\n");
+}
+
+void __init tx3927_time_init(unsigned int evt_tmrnr, unsigned int src_tmrnr)
+{
+ txx9_clockevent_init(TX3927_TMR_REG(evt_tmrnr),
+ TXX9_IRQ_BASE + TX3927_IR_TMR(evt_tmrnr),
+ TXX9_IMCLK);
+ txx9_clocksource_init(TX3927_TMR_REG(src_tmrnr), TXX9_IMCLK);
+}
+
+void __init tx3927_sio_init(unsigned int sclk, unsigned int cts_mask)
+{
+ int i;
+
+ for (i = 0; i < 2; i++)
+ txx9_sio_init(TX3927_SIO_REG(i),
+ TXX9_IRQ_BASE + TX3927_IR_SIO(i),
+ i, sclk, (1 << i) & cts_mask);
+}
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/delay.h>
-#include <linux/serial_core.h>
#include <linux/param.h>
#include <asm/txx9irq.h>
#include <asm/txx9tmr.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/tx4927.h>
-void __init tx4927_wdr_init(void)
+static void __init tx4927_wdr_init(void)
{
/* clear WatchDogReset (W1C) */
tx4927_ccfg_set(TX4927_CCFG_WDRST);
tx4927_ccfg_set(TX4927_CCFG_WR);
}
+void __init tx4927_wdt_init(void)
+{
+ txx9_wdt_init(TX4927_TMR_REG(2) & 0xfffffffffULL);
+}
+
static struct resource tx4927_sdram_resource[4];
void __init tx4927_setup(void)
TXX9_IMCLK);
}
-void __init tx4927_setup_serial(void)
+void __init tx4927_sio_init(unsigned int sclk, unsigned int cts_mask)
{
-#ifdef CONFIG_SERIAL_TXX9
int i;
- struct uart_port req;
-
- for (i = 0; i < 2; i++) {
- memset(&req, 0, sizeof(req));
- req.line = i;
- req.iotype = UPIO_MEM;
- req.membase = (unsigned char __iomem *)TX4927_SIO_REG(i);
- req.mapbase = TX4927_SIO_REG(i) & 0xfffffffffULL;
- req.irq = TXX9_IRQ_BASE + TX4927_IR_SIO(i);
- req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
- req.uartclk = TXX9_IMCLK;
- early_serial_txx9_setup(&req);
- }
-#endif /* CONFIG_SERIAL_TXX9 */
+
+ for (i = 0; i < 2; i++)
+ txx9_sio_init(TX4927_SIO_REG(i) & 0xfffffffffULL,
+ TXX9_IRQ_BASE + TX4927_IR_SIO(i),
+ i, sclk, (1 << i) & cts_mask);
}
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/delay.h>
-#include <linux/serial_core.h>
#include <linux/param.h>
#include <asm/txx9irq.h>
#include <asm/txx9tmr.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/tx4938.h>
-void __init tx4938_wdr_init(void)
+static void __init tx4938_wdr_init(void)
{
/* clear WatchDogReset (W1C) */
tx4938_ccfg_set(TX4938_CCFG_WDRST);
tx4938_ccfg_set(TX4938_CCFG_WR);
}
+void __init tx4938_wdt_init(void)
+{
+ txx9_wdt_init(TX4938_TMR_REG(2) & 0xfffffffffULL);
+}
+
static struct resource tx4938_sdram_resource[4];
static struct resource tx4938_sram_resource;
TXX9_IMCLK);
}
-void __init tx4938_setup_serial(void)
+void __init tx4938_sio_init(unsigned int sclk, unsigned int cts_mask)
{
-#ifdef CONFIG_SERIAL_TXX9
int i;
- struct uart_port req;
unsigned int ch_mask = 0;
if (__raw_readq(&tx4938_ccfgptr->pcfg) & TX4938_PCFG_ETH0_SEL)
for (i = 0; i < 2; i++) {
if ((1 << i) & ch_mask)
continue;
- memset(&req, 0, sizeof(req));
- req.line = i;
- req.iotype = UPIO_MEM;
- req.membase = (unsigned char __iomem *)TX4938_SIO_REG(i);
- req.mapbase = TX4938_SIO_REG(i) & 0xfffffffffULL;
- req.irq = TXX9_IRQ_BASE + TX4938_IR_SIO(i);
- req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
- req.uartclk = TXX9_IMCLK;
- early_serial_txx9_setup(&req);
+ txx9_sio_init(TX4938_SIO_REG(i) & 0xfffffffffULL,
+ TXX9_IRQ_BASE + TX4938_IR_SIO(i),
+ i, sclk, (1 << i) & cts_mask);
}
-#endif /* CONFIG_SERIAL_TXX9 */
+}
+
+void __init tx4938_spi_init(int busid)
+{
+ txx9_spi_init(busid, TX4938_SPI_REG & 0xfffffffffULL,
+ TXX9_IRQ_BASE + TX4938_IR_SPI);
+}
+
+void __init tx4938_ethaddr_init(unsigned char *addr0, unsigned char *addr1)
+{
+ u64 pcfg = __raw_readq(&tx4938_ccfgptr->pcfg);
+
+ if (addr0 && (pcfg & TX4938_PCFG_ETH0_SEL))
+ txx9_ethaddr_init(TXX9_IRQ_BASE + TX4938_IR_ETH0, addr0);
+ if (addr1 && (pcfg & TX4938_PCFG_ETH1_SEL))
+ txx9_ethaddr_init(TXX9_IRQ_BASE + TX4938_IR_ETH1, addr1);
}
#include <asm/io.h>
#include <asm/txx9/smsc_fdc37m81x.h>
-#define DEBUG
-
/* Common Registers */
#define SMSC_FDC37M81X_CONFIG_INDEX 0x00
#define SMSC_FDC37M81X_CONFIG_DATA 0x01
#define SMSC_FDC37M81X_CONFIG_EXIT 0xaa
#define SMSC_FDC37M81X_CHIP_ID 0x4d
-static unsigned long g_smsc_fdc37m81x_base = 0;
+static unsigned long g_smsc_fdc37m81x_base;
static inline unsigned char smsc_fdc37m81x_rd(unsigned char index)
{
u8 chip_id;
if (g_smsc_fdc37m81x_base)
- printk("smsc_fdc37m81x_init() stepping on old base=0x%0*lx\n",
+ printk(KERN_WARNING "%s: stepping on old base=0x%0*lx\n",
+ __func__,
field, g_smsc_fdc37m81x_base);
g_smsc_fdc37m81x_base = port;
if (chip_id == SMSC_FDC37M81X_CHIP_ID)
smsc_fdc37m81x_config_end();
else {
- printk("smsc_fdc37m81x_init() unknow chip id 0x%02x\n",
+ printk(KERN_WARNING "%s: unknow chip id 0x%02x\n", __func__,
chip_id);
g_smsc_fdc37m81x_base = 0;
}
}
#ifdef DEBUG
-void smsc_fdc37m81x_config_dump_one(char *key, u8 dev, u8 reg)
+static void smsc_fdc37m81x_config_dump_one(const char *key, u8 dev, u8 reg)
{
- printk("%s: dev=0x%02x reg=0x%02x val=0x%02x\n", key, dev, reg,
+ printk(KERN_INFO "%s: dev=0x%02x reg=0x%02x val=0x%02x\n",
+ key, dev, reg,
smsc_fdc37m81x_rd(reg));
}
void smsc_fdc37m81x_config_dump(void)
{
u8 orig;
- char *fname = "smsc_fdc37m81x_config_dump()";
+ const char *fname = __func__;
smsc_fdc37m81x_config_beg();
orig = smsc_fdc37m81x_rd(SMSC_FDC37M81X_DNUM);
- printk("%s: common\n", fname);
+ printk(KERN_INFO "%s: common\n", fname);
smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
SMSC_FDC37M81X_DNUM);
smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
SMSC_FDC37M81X_PMGT);
- printk("%s: keyboard\n", fname);
+ printk(KERN_INFO "%s: keyboard\n", fname);
smsc_dc37m81x_wr(SMSC_FDC37M81X_DNUM, SMSC_FDC37M81X_KBD);
smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_KBD,
SMSC_FDC37M81X_ACTIVE);
#
obj-y += prom.o irq.o setup.o
-obj-$(CONFIG_KGDB) += kgdb_io.o
EXTRA_CFLAGS += -Werror
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
-#include <linux/sched.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <asm/io.h>
#include <asm/mipsregs.h>
-#include <asm/system.h>
-
-#include <asm/processor.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/jmr3927.h>
#error JMR3927_IRQ_END > NR_IRQS
#endif
-static unsigned char irc_level[TX3927_NUM_IR] = {
- 5, 5, 5, 5, 5, 5, /* INT[5:0] */
- 7, 7, /* SIO */
- 5, 5, 5, 0, 0, /* DMA, PIO, PCI */
- 6, 6, 6 /* TMR */
-};
-
/*
* CP0_STATUS is a thread's resource (saved/restored on context switch).
* So disable_irq/enable_irq MUST handle IOC/IRC registers.
return irq;
}
-#ifdef CONFIG_PCI
-static irqreturn_t jmr3927_pcierr_interrupt(int irq, void *dev_id)
-{
- printk(KERN_WARNING "PCI error interrupt (irq 0x%x).\n", irq);
- printk(KERN_WARNING "pcistat:%02x, lbstat:%04lx\n",
- tx3927_pcicptr->pcistat, tx3927_pcicptr->lbstat);
-
- return IRQ_HANDLED;
-}
-static struct irqaction pcierr_action = {
- .handler = jmr3927_pcierr_interrupt,
- .mask = CPU_MASK_NONE,
- .name = "PCI error",
+static struct irq_chip jmr3927_irq_ioc = {
+ .name = "jmr3927_ioc",
+ .ack = mask_irq_ioc,
+ .mask = mask_irq_ioc,
+ .mask_ack = mask_irq_ioc,
+ .unmask = unmask_irq_ioc,
};
-#endif
-
-static void __init jmr3927_irq_init(void);
void __init jmr3927_irq_setup(void)
{
+ int i;
+
txx9_irq_dispatch = jmr3927_irq_dispatch;
/* Now, interrupt control disabled, */
/* all IRC interrupts are masked, */
/* clear PCI Reset interrupts */
jmr3927_ioc_reg_out(0, JMR3927_IOC_RESET_ADDR);
- jmr3927_irq_init();
+ tx3927_irq_init();
+ for (i = JMR3927_IRQ_IOC; i < JMR3927_IRQ_IOC + JMR3927_NR_IRQ_IOC; i++)
+ set_irq_chip_and_handler(i, &jmr3927_irq_ioc, handle_level_irq);
/* setup IOC interrupt 1 (PCI, MODEM) */
set_irq_chained_handler(JMR3927_IRQ_IOCINT, handle_simple_irq);
-
-#ifdef CONFIG_PCI
- setup_irq(JMR3927_IRQ_IRC_PCI, &pcierr_action);
-#endif
-
- /* enable all CPU interrupt bits. */
- set_c0_status(ST0_IM); /* IE bit is still 0. */
-}
-
-static struct irq_chip jmr3927_irq_ioc = {
- .name = "jmr3927_ioc",
- .ack = mask_irq_ioc,
- .mask = mask_irq_ioc,
- .mask_ack = mask_irq_ioc,
- .unmask = unmask_irq_ioc,
-};
-
-static void __init jmr3927_irq_init(void)
-{
- u32 i;
-
- txx9_irq_init(TX3927_IRC_REG);
- for (i = 0; i < TXx9_MAX_IR; i++)
- txx9_irq_set_pri(i, irc_level[i]);
- for (i = JMR3927_IRQ_IOC; i < JMR3927_IRQ_IOC + JMR3927_NR_IRQ_IOC; i++)
- set_irq_chip_and_handler(i, &jmr3927_irq_ioc, handle_level_irq);
}
+++ /dev/null
-/*
- * BRIEF MODULE DESCRIPTION
- * Low level uart routines to directly access a TX[34]927 SIO.
- *
- * Copyright 2001 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ahennessy@mvista.com or source@mvista.com
- *
- * Based on arch/mips/ddb5xxx/ddb5477/kgdb_io.c
- *
- * Copyright (C) 2000-2001 Toshiba Corporation
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <asm/txx9/jmr3927.h>
-
-#define TIMEOUT 0xffffff
-
-static int remoteDebugInitialized = 0;
-static void debugInit(int baud);
-
-int putDebugChar(unsigned char c)
-{
- int i = 0;
-
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(38400);
- }
-
- do {
- slow_down();
- i++;
- if (i>TIMEOUT) {
- break;
- }
- } while (!(tx3927_sioptr(0)->cisr & TXx927_SICISR_TXALS));
- tx3927_sioptr(0)->tfifo = c;
-
- return 1;
-}
-
-unsigned char getDebugChar(void)
-{
- int i = 0;
- int dicr;
- char c;
-
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(38400);
- }
-
- /* diable RX int. */
- dicr = tx3927_sioptr(0)->dicr;
- tx3927_sioptr(0)->dicr = 0;
-
- do {
- slow_down();
- i++;
- if (i>TIMEOUT) {
- break;
- }
- } while (tx3927_sioptr(0)->disr & TXx927_SIDISR_UVALID)
- ;
- c = tx3927_sioptr(0)->rfifo;
-
- /* clear RX int. status */
- tx3927_sioptr(0)->disr &= ~TXx927_SIDISR_RDIS;
- /* enable RX int. */
- tx3927_sioptr(0)->dicr = dicr;
-
- return c;
-}
-
-static void debugInit(int baud)
-{
- tx3927_sioptr(0)->lcr = 0x020;
- tx3927_sioptr(0)->dicr = 0;
- tx3927_sioptr(0)->disr = 0x4100;
- tx3927_sioptr(0)->cisr = 0x014;
- tx3927_sioptr(0)->fcr = 0;
- tx3927_sioptr(0)->flcr = 0x02;
- tx3927_sioptr(0)->bgr = ((JMR3927_BASE_BAUD + baud / 2) / baud) |
- TXx927_SIBGR_BCLK_T0;
-}
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
+#include <linux/kernel.h>
#include <asm/bootinfo.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/jmr3927.h>
-#define TIMEOUT 0xffffff
-
-void
-prom_putchar(char c)
-{
- int i = 0;
-
- do {
- i++;
- if (i>TIMEOUT)
- break;
- } while (!(tx3927_sioptr(1)->cisr & TXx927_SICISR_TXALS));
- tx3927_sioptr(1)->tfifo = c;
- return;
-}
-
-void
-puts(const char *cp)
-{
- while (*cp)
- prom_putchar(*cp++);
- prom_putchar('\r');
- prom_putchar('\n');
-}
-
void __init jmr3927_prom_init(void)
{
/* CCFG */
if ((tx3927_ccfgptr->ccfg & TX3927_CCFG_TLBOFF) == 0)
- puts("Warning: TX3927 TLB off\n");
+ printk(KERN_ERR "TX3927 TLB off\n");
prom_init_cmdline();
add_memory_region(0, JMR3927_SDRAM_SIZE, BOOT_MEM_RAM);
+ txx9_sio_putchar_init(TX3927_SIO_REG(1));
}
#include <linux/types.h>
#include <linux/ioport.h>
#include <linux/delay.h>
-#include <linux/pm.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
-#ifdef CONFIG_SERIAL_TXX9
-#include <linux/serial_core.h>
-#endif
-#include <asm/txx9tmr.h>
-#include <asm/txx9pio.h>
#include <asm/reboot.h>
+#include <asm/txx9pio.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/pci.h>
#include <asm/txx9/jmr3927.h>
#include <asm/mipsregs.h>
-extern void puts(const char *cp);
-
-/* don't enable - see errata */
-static int jmr3927_ccfg_toeon;
-
-static inline void do_reset(void)
+static void jmr3927_machine_restart(char *command)
{
+ local_irq_disable();
#if 1 /* Resetting PCI bus */
jmr3927_ioc_reg_out(0, JMR3927_IOC_RESET_ADDR);
jmr3927_ioc_reg_out(JMR3927_IOC_RESET_PCI, JMR3927_IOC_RESET_ADDR);
jmr3927_ioc_reg_out(0, JMR3927_IOC_RESET_ADDR);
#endif
jmr3927_ioc_reg_out(JMR3927_IOC_RESET_CPU, JMR3927_IOC_RESET_ADDR);
-}
-
-static void jmr3927_machine_restart(char *command)
-{
- local_irq_disable();
- puts("Rebooting...");
- do_reset();
-}
-
-static void jmr3927_machine_halt(void)
-{
- puts("JMR-TX3927 halted.\n");
- while (1);
-}
-
-static void jmr3927_machine_power_off(void)
-{
- puts("JMR-TX3927 halted. Please turn off the power.\n");
- while (1);
+ /* fallback */
+ (*_machine_halt)();
}
static void __init jmr3927_time_init(void)
{
- txx9_clockevent_init(TX3927_TMR_REG(0),
- TXX9_IRQ_BASE + JMR3927_IRQ_IRC_TMR(0),
- JMR3927_IMCLK);
- txx9_clocksource_init(TX3927_TMR_REG(1), JMR3927_IMCLK);
+ tx3927_time_init(0, 1);
}
#define DO_WRITE_THROUGH
set_io_port_base(JMR3927_PORT_BASE + JMR3927_PCIIO);
_machine_restart = jmr3927_machine_restart;
- _machine_halt = jmr3927_machine_halt;
- pm_power_off = jmr3927_machine_power_off;
-
- /* Reboot on panic */
- panic_timeout = 180;
/* cache setup */
{
#endif
conf = read_c0_conf();
- conf &= ~(TX39_CONF_ICE | TX39_CONF_DCE | TX39_CONF_WBON | TX39_CONF_CWFON);
+ conf &= ~(TX39_CONF_ICE | TX39_CONF_DCE |
+ TX39_CONF_WBON | TX39_CONF_CWFON);
conf |= mips_ic_disable ? 0 : TX39_CONF_ICE;
conf |= mips_dc_disable ? 0 : TX39_CONF_DCE;
conf |= mips_config_wbon ? TX39_CONF_WBON : 0;
/* initialize board */
jmr3927_board_init();
- argptr = prom_getcmdline();
-
- if ((argptr = strstr(argptr, "toeon")) != NULL)
- jmr3927_ccfg_toeon = 1;
- argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "ip=")) == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " ip=bootp");
- }
-
-#ifdef CONFIG_SERIAL_TXX9
- {
- extern int early_serial_txx9_setup(struct uart_port *port);
- int i;
- struct uart_port req;
- for(i = 0; i < 2; i++) {
- memset(&req, 0, sizeof(req));
- req.line = i;
- req.iotype = UPIO_MEM;
- req.membase = (unsigned char __iomem *)TX3927_SIO_REG(i);
- req.mapbase = TX3927_SIO_REG(i);
- req.irq = i == 0 ?
- JMR3927_IRQ_IRC_SIO0 : JMR3927_IRQ_IRC_SIO1;
- if (i == 0)
- req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
- req.uartclk = JMR3927_IMCLK;
- early_serial_txx9_setup(&req);
- }
- }
+ tx3927_sio_init(0, 1 << 1); /* ch1: noCTS */
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
argptr = prom_getcmdline();
- if ((argptr = strstr(argptr, "console=")) == NULL) {
- argptr = prom_getcmdline();
+ if (!strstr(argptr, "console="))
strcat(argptr, " console=ttyS1,115200");
- }
-#endif
#endif
}
-static void tx3927_setup(void);
-
static void __init jmr3927_pci_setup(void)
{
#ifdef CONFIG_PCI
jmr3927_ioc_reg_out(0, JMR3927_IOC_RESET_ADDR);
}
tx3927_pcic_setup(c, JMR3927_SDRAM_SIZE, extarb);
+ tx3927_setup_pcierr_irq();
#endif /* CONFIG_PCI */
}
static void __init jmr3927_board_init(void)
{
- tx3927_setup();
- jmr3927_pci_setup();
-
- /* SIO0 DTR on */
- jmr3927_ioc_reg_out(0, JMR3927_IOC_DTR_ADDR);
-
- jmr3927_led_set(0);
-
- printk("JMR-TX3927 (Rev %d) --- IOC(Rev %d) DIPSW:%d,%d,%d,%d\n",
- jmr3927_ioc_reg_in(JMR3927_IOC_BREV_ADDR) & JMR3927_REV_MASK,
- jmr3927_ioc_reg_in(JMR3927_IOC_REV_ADDR) & JMR3927_REV_MASK,
- jmr3927_dipsw1(), jmr3927_dipsw2(),
- jmr3927_dipsw3(), jmr3927_dipsw4());
-}
-
-static void __init tx3927_setup(void)
-{
- int i;
-
txx9_cpu_clock = JMR3927_CORECLK;
- txx9_gbus_clock = JMR3927_GBUSCLK;
/* SDRAMC are configured by PROM */
/* ROMC */
tx3927_romcptr->cr[3] = JMR3927_ROMCE3 | 0x0003f698;
tx3927_romcptr->cr[5] = JMR3927_ROMCE5 | 0x0000f218;
- /* CCFG */
- /* enable Timeout BusError */
- if (jmr3927_ccfg_toeon)
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_TOE;
-
- /* clear BusErrorOnWrite flag */
- tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_BEOW;
- /* Disable PCI snoop */
- tx3927_ccfgptr->ccfg &= ~TX3927_CCFG_PSNP;
- /* do reset on watchdog */
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_WR;
-
-#ifdef DO_WRITE_THROUGH
- /* Enable PCI SNOOP - with write through only */
- tx3927_ccfgptr->ccfg |= TX3927_CCFG_PSNP;
-#endif
-
/* Pin selection */
tx3927_ccfgptr->pcfg &= ~TX3927_PCFG_SELALL;
tx3927_ccfgptr->pcfg |=
TX3927_PCFG_SELSIOC(0) | TX3927_PCFG_SELSIO_ALL |
(TX3927_PCFG_SELDMA_ALL & ~TX3927_PCFG_SELDMA(1));
- printk("TX3927 -- CRIR:%08lx CCFG:%08lx PCFG:%08lx\n",
- tx3927_ccfgptr->crir,
- tx3927_ccfgptr->ccfg, tx3927_ccfgptr->pcfg);
-
- /* TMR */
- for (i = 0; i < TX3927_NR_TMR; i++)
- txx9_tmr_init(TX3927_TMR_REG(i));
-
- /* DMA */
- tx3927_dmaptr->mcr = 0;
- for (i = 0; i < ARRAY_SIZE(tx3927_dmaptr->ch); i++) {
- /* reset channel */
- tx3927_dmaptr->ch[i].ccr = TX3927_DMA_CCR_CHRST;
- tx3927_dmaptr->ch[i].ccr = 0;
- }
- /* enable DMA */
-#ifdef __BIG_ENDIAN
- tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN;
-#else
- tx3927_dmaptr->mcr = TX3927_DMA_MCR_MSTEN | TX3927_DMA_MCR_LE;
-#endif
+ tx3927_setup();
- /* PIO */
/* PIO[15:12] connected to LEDs */
__raw_writel(0x0000f000, &tx3927_pioptr->dir);
- __raw_writel(0, &tx3927_pioptr->maskcpu);
- __raw_writel(0, &tx3927_pioptr->maskext);
- txx9_gpio_init(TX3927_PIO_REG, 0, 16);
gpio_request(11, "dipsw1");
gpio_request(10, "dipsw2");
- {
- unsigned int conf;
- conf = read_c0_conf();
- if (!(conf & TX39_CONF_ICE))
- printk("TX3927 I-Cache disabled.\n");
- if (!(conf & TX39_CONF_DCE))
- printk("TX3927 D-Cache disabled.\n");
- else if (!(conf & TX39_CONF_WBON))
- printk("TX3927 D-Cache WriteThrough.\n");
- else if (!(conf & TX39_CONF_CWFON))
- printk("TX3927 D-Cache WriteBack.\n");
- else
- printk("TX3927 D-Cache WriteBack (CWF) .\n");
- }
+ jmr3927_pci_setup();
+
+ /* SIO0 DTR on */
+ jmr3927_ioc_reg_out(0, JMR3927_IOC_DTR_ADDR);
+
+ jmr3927_led_set(0);
+
+ printk(KERN_INFO
+ "JMR-TX3927 (Rev %d) --- IOC(Rev %d) DIPSW:%d,%d,%d,%d\n",
+ jmr3927_ioc_reg_in(JMR3927_IOC_BREV_ADDR) & JMR3927_REV_MASK,
+ jmr3927_ioc_reg_in(JMR3927_IOC_REV_ADDR) & JMR3927_REV_MASK,
+ jmr3927_dipsw1(), jmr3927_dipsw2(),
+ jmr3927_dipsw3(), jmr3927_dipsw4());
}
/* This trick makes rtc-ds1742 driver usable as is. */
#endif
}
-static int __init jmr3927_rtc_init(void)
+static void __init jmr3927_rtc_init(void)
{
static struct resource __initdata res = {
.start = JMR3927_IOC_NVRAMB_ADDR - IO_BASE,
.end = JMR3927_IOC_NVRAMB_ADDR - IO_BASE + 0x800 - 1,
.flags = IORESOURCE_MEM,
};
- struct platform_device *dev;
- dev = platform_device_register_simple("rtc-ds1742", -1, &res, 1);
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
-}
-
-/* Watchdog support */
-
-static int __init txx9_wdt_init(unsigned long base)
-{
- struct resource res = {
- .start = base,
- .end = base + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- };
- struct platform_device *dev =
- platform_device_register_simple("txx9wdt", -1, &res, 1);
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
-}
-
-static int __init jmr3927_wdt_init(void)
-{
- return txx9_wdt_init(TX3927_TMR_REG(2));
+ platform_device_register_simple("rtc-ds1742", -1, &res, 1);
}
static void __init jmr3927_device_init(void)
{
__swizzle_addr_b = jmr3927_swizzle_addr_b;
jmr3927_rtc_init();
- jmr3927_wdt_init();
+ tx3927_wdt_init();
}
struct txx9_board_vec jmr3927_vec __initdata = {
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
-IRQ Device
-00 RBTX4927-ISA/00
-01 RBTX4927-ISA/01 PS2/Keyboard
-02 RBTX4927-ISA/02 Cascade RBTX4927-ISA (irqs 8-15)
-03 RBTX4927-ISA/03
-04 RBTX4927-ISA/04
-05 RBTX4927-ISA/05
-06 RBTX4927-ISA/06
-07 RBTX4927-ISA/07
-08 RBTX4927-ISA/08
-09 RBTX4927-ISA/09
-10 RBTX4927-ISA/10
-11 RBTX4927-ISA/11
-12 RBTX4927-ISA/12 PS2/Mouse (not supported at this time)
-13 RBTX4927-ISA/13
-14 RBTX4927-ISA/14 IDE
-15 RBTX4927-ISA/15
-
-16 TX4927-CP0/00 Software 0
-17 TX4927-CP0/01 Software 1
-18 TX4927-CP0/02 Cascade TX4927-CP0
-19 TX4927-CP0/03 Multiplexed -- do not use
-20 TX4927-CP0/04 Multiplexed -- do not use
-21 TX4927-CP0/05 Multiplexed -- do not use
-22 TX4927-CP0/06 Multiplexed -- do not use
-23 TX4927-CP0/07 CPU TIMER
-
-24 TX4927-PIC/00
-25 TX4927-PIC/01
-26 TX4927-PIC/02
-27 TX4927-PIC/03 Cascade RBTX4927-IOC
-28 TX4927-PIC/04
-29 TX4927-PIC/05 RBTX4927 RTL-8019AS ethernet
-30 TX4927-PIC/06
-31 TX4927-PIC/07
-32 TX4927-PIC/08 TX4927 SerialIO Channel 0
-33 TX4927-PIC/09 TX4927 SerialIO Channel 1
-34 TX4927-PIC/10
-35 TX4927-PIC/11
-36 TX4927-PIC/12
-37 TX4927-PIC/13
-38 TX4927-PIC/14
-39 TX4927-PIC/15
-40 TX4927-PIC/16 TX4927 PCI PCI-C
-41 TX4927-PIC/17
-42 TX4927-PIC/18
-43 TX4927-PIC/19
-44 TX4927-PIC/20
-45 TX4927-PIC/21
-46 TX4927-PIC/22 TX4927 PCI PCI-ERR
-47 TX4927-PIC/23 TX4927 PCI PCI-PMA (not used)
-48 TX4927-PIC/24
-49 TX4927-PIC/25
-50 TX4927-PIC/26
-51 TX4927-PIC/27
-52 TX4927-PIC/28
-53 TX4927-PIC/29
-54 TX4927-PIC/30
-55 TX4927-PIC/31
-
-56 RBTX4927-IOC/00 FPCIB0 PCI-D PJ4/A PJ5/B SB/C PJ6/D PJ7/A (SouthBridge/NotUsed) [RTL-8139=PJ4]
-57 RBTX4927-IOC/01 FPCIB0 PCI-C PJ4/D PJ5/A SB/B PJ6/C PJ7/D (SouthBridge/NotUsed) [RTL-8139=PJ5]
-58 RBTX4927-IOC/02 FPCIB0 PCI-B PJ4/C PJ5/D SB/A PJ6/B PJ7/C (SouthBridge/IDE/pin=1,INTR) [RTL-8139=NotSupported]
-59 RBTX4927-IOC/03 FPCIB0 PCI-A PJ4/B PJ5/C SB/D PJ6/A PJ7/B (SouthBridge/USB/pin=4) [RTL-8139=PJ6]
-60 RBTX4927-IOC/04
-61 RBTX4927-IOC/05
-62 RBTX4927-IOC/06
-63 RBTX4927-IOC/07
-
-NOTES:
-SouthBridge/INTR is mapped to SouthBridge/A=PCI-B/#58
-SouthBridge/ISA/pin=0 no pci irq used by this device
-SouthBridge/IDE/pin=1 no pci irq used by this device, using INTR via ISA IRQ14
-SouthBridge/USB/pin=4 using pci irq SouthBridge/D=PCI-A=#59
-SouthBridge/PMC/pin=0 no pci irq used by this device
-SuperIO/PS2/Keyboard, using INTR via ISA IRQ1
-SuperIO/PS2/Mouse, using INTR via ISA IRQ12 (mouse not currently supported)
-JP7 is not bus master -- do NOT use -- only 4 pci bus master's allowed -- SouthBridge, JP4, JP5, JP6
-*/
+ * I8259A_IRQ_BASE+00
+ * I8259A_IRQ_BASE+01 PS2/Keyboard
+ * I8259A_IRQ_BASE+02 Cascade RBTX4927-ISA (irqs 8-15)
+ * I8259A_IRQ_BASE+03
+ * I8259A_IRQ_BASE+04
+ * I8259A_IRQ_BASE+05
+ * I8259A_IRQ_BASE+06
+ * I8259A_IRQ_BASE+07
+ * I8259A_IRQ_BASE+08
+ * I8259A_IRQ_BASE+09
+ * I8259A_IRQ_BASE+10
+ * I8259A_IRQ_BASE+11
+ * I8259A_IRQ_BASE+12 PS2/Mouse (not supported at this time)
+ * I8259A_IRQ_BASE+13
+ * I8259A_IRQ_BASE+14 IDE
+ * I8259A_IRQ_BASE+15
+ *
+ * MIPS_CPU_IRQ_BASE+00 Software 0
+ * MIPS_CPU_IRQ_BASE+01 Software 1
+ * MIPS_CPU_IRQ_BASE+02 Cascade TX4927-CP0
+ * MIPS_CPU_IRQ_BASE+03 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+04 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+05 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+06 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+07 CPU TIMER
+ *
+ * TXX9_IRQ_BASE+00
+ * TXX9_IRQ_BASE+01
+ * TXX9_IRQ_BASE+02
+ * TXX9_IRQ_BASE+03 Cascade RBTX4927-IOC
+ * TXX9_IRQ_BASE+04
+ * TXX9_IRQ_BASE+05 RBTX4927 RTL-8019AS ethernet
+ * TXX9_IRQ_BASE+06
+ * TXX9_IRQ_BASE+07
+ * TXX9_IRQ_BASE+08 TX4927 SerialIO Channel 0
+ * TXX9_IRQ_BASE+09 TX4927 SerialIO Channel 1
+ * TXX9_IRQ_BASE+10
+ * TXX9_IRQ_BASE+11
+ * TXX9_IRQ_BASE+12
+ * TXX9_IRQ_BASE+13
+ * TXX9_IRQ_BASE+14
+ * TXX9_IRQ_BASE+15
+ * TXX9_IRQ_BASE+16 TX4927 PCI PCI-C
+ * TXX9_IRQ_BASE+17
+ * TXX9_IRQ_BASE+18
+ * TXX9_IRQ_BASE+19
+ * TXX9_IRQ_BASE+20
+ * TXX9_IRQ_BASE+21
+ * TXX9_IRQ_BASE+22 TX4927 PCI PCI-ERR
+ * TXX9_IRQ_BASE+23 TX4927 PCI PCI-PMA (not used)
+ * TXX9_IRQ_BASE+24
+ * TXX9_IRQ_BASE+25
+ * TXX9_IRQ_BASE+26
+ * TXX9_IRQ_BASE+27
+ * TXX9_IRQ_BASE+28
+ * TXX9_IRQ_BASE+29
+ * TXX9_IRQ_BASE+30
+ * TXX9_IRQ_BASE+31
+ *
+ * RBTX4927_IRQ_IOC+00 FPCIB0 PCI-D (SouthBridge)
+ * RBTX4927_IRQ_IOC+01 FPCIB0 PCI-C (SouthBridge)
+ * RBTX4927_IRQ_IOC+02 FPCIB0 PCI-B (SouthBridge/IDE/pin=1,INTR)
+ * RBTX4927_IRQ_IOC+03 FPCIB0 PCI-A (SouthBridge/USB/pin=4)
+ * RBTX4927_IRQ_IOC+04
+ * RBTX4927_IRQ_IOC+05
+ * RBTX4927_IRQ_IOC+06
+ * RBTX4927_IRQ_IOC+07
+ *
+ * NOTES:
+ * SouthBridge/INTR is mapped to SouthBridge/A=PCI-B/#58
+ * SouthBridge/ISA/pin=0 no pci irq used by this device
+ * SouthBridge/IDE/pin=1 no pci irq used by this device, using INTR
+ * via ISA IRQ14
+ * SouthBridge/USB/pin=4 using pci irq SouthBridge/D=PCI-A=#59
+ * SouthBridge/PMC/pin=0 no pci irq used by this device
+ * SuperIO/PS2/Keyboard, using INTR via ISA IRQ1
+ * SuperIO/PS2/Mouse, using INTR via ISA IRQ12 (mouse not currently supported)
+ * JP7 is not bus master -- do NOT use -- only 4 pci bus master's
+ * allowed -- SouthBridge, JP4, JP5, JP6
+ */
#include <linux/init.h>
#include <linux/types.h>
level3 = readb(rbtx4927_imstat_addr) & 0x1f;
if (level3)
sw_irq = RBTX4927_IRQ_IOC + fls(level3) - 1;
- return (sw_irq);
+ return sw_irq;
}
static void __init toshiba_rbtx4927_irq_ioc_init(void)
{
prom_init_cmdline();
add_memory_region(0, tx4927_get_mem_size(), BOOT_MEM_RAM);
+ txx9_sio_putchar_init(TX4927_SIO_REG(0) & 0xfffffffffULL);
}
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/pm.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <asm/io.h>
-#include <asm/processor.h>
#include <asm/reboot.h>
#include <asm/txx9/generic.h>
#include <asm/txx9/pci.h>
tx4927_report_pciclk();
tx4927_pcic_setup(tx4927_pcicptr, c, extarb);
}
+ tx4927_setup_pcierr_irq();
}
static void __init tx4937_pci_setup(void)
tx4938_report_pciclk();
tx4927_pcic_setup(tx4938_pcicptr, c, extarb);
}
+ tx4938_setup_pcierr_irq();
}
static void __init rbtx4927_arch_init(void)
#define rbtx4937_arch_init NULL
#endif /* CONFIG_PCI */
-static void __noreturn wait_forever(void)
-{
- while (1)
- if (cpu_wait)
- (*cpu_wait)();
-}
-
static void toshiba_rbtx4927_restart(char *command)
{
- printk(KERN_NOTICE "System Rebooting...\n");
-
/* enable the s/w reset register */
writeb(1, rbtx4927_softresetlock_addr);
/* do a s/w reset */
writeb(1, rbtx4927_softreset_addr);
- /* do something passive while waiting for reset */
- local_irq_disable();
- wait_forever();
- /* no return */
-}
-
-static void toshiba_rbtx4927_halt(void)
-{
- printk(KERN_NOTICE "System Halted\n");
- local_irq_disable();
- wait_forever();
- /* no return */
-}
-
-static void toshiba_rbtx4927_power_off(void)
-{
- toshiba_rbtx4927_halt();
- /* no return */
+ /* fallback */
+ (*_machine_halt)();
}
static void __init rbtx4927_clock_init(void);
u32 cp0_config;
char *argptr;
- /* f/w leaves this on at startup */
- clear_c0_status(ST0_ERL);
-
/* enable caches -- HCP5 does this, pmon does not */
cp0_config = read_c0_config();
cp0_config = cp0_config & ~(TX49_CONF_IC | TX49_CONF_DC);
}
_machine_restart = toshiba_rbtx4927_restart;
- _machine_halt = toshiba_rbtx4927_halt;
- pm_power_off = toshiba_rbtx4927_power_off;
#ifdef CONFIG_PCI
txx9_alloc_pci_controller(&txx9_primary_pcic,
RBTX4927_PCIMEM, RBTX4927_PCIMEM_SIZE,
RBTX4927_PCIIO, RBTX4927_PCIIO_SIZE);
+ txx9_board_pcibios_setup = tx4927_pcibios_setup;
#else
set_io_port_base(KSEG1 + RBTX4927_ISA_IO_OFFSET);
#endif
- tx4927_setup_serial();
+ tx4927_sio_init(0, 0);
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
- argptr = prom_getcmdline();
- if (strstr(argptr, "console=") == NULL) {
- strcat(argptr, " console=ttyS0,38400");
- }
-#endif
-
-#ifdef CONFIG_ROOT_NFS
- argptr = prom_getcmdline();
- if (strstr(argptr, "root=") == NULL) {
- strcat(argptr, " root=/dev/nfs rw");
- }
-#endif
-
-#ifdef CONFIG_IP_PNP
- argptr = prom_getcmdline();
- if (strstr(argptr, "ip=") == NULL) {
- strcat(argptr, " ip=any");
- }
+ argptr = prom_getcmdline();
+ if (!strstr(argptr, "console="))
+ strcat(argptr, " console=ttyS0,38400");
#endif
}
tx4927_time_init(0);
}
-static int __init toshiba_rbtx4927_rtc_init(void)
+static void __init toshiba_rbtx4927_rtc_init(void)
{
struct resource res = {
.start = RBTX4927_BRAMRTC_BASE - IO_BASE,
.end = RBTX4927_BRAMRTC_BASE - IO_BASE + 0x800 - 1,
.flags = IORESOURCE_MEM,
};
- struct platform_device *dev =
- platform_device_register_simple("rtc-ds1742", -1, &res, 1);
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
+ platform_device_register_simple("rtc-ds1742", -1, &res, 1);
}
-static int __init rbtx4927_ne_init(void)
+static void __init rbtx4927_ne_init(void)
{
struct resource res[] = {
{
.flags = IORESOURCE_IRQ,
}
};
- struct platform_device *dev =
- platform_device_register_simple("ne", -1,
- res, ARRAY_SIZE(res));
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
-}
-
-/* Watchdog support */
-
-static int __init txx9_wdt_init(unsigned long base)
-{
- struct resource res = {
- .start = base,
- .end = base + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- };
- struct platform_device *dev =
- platform_device_register_simple("txx9wdt", -1, &res, 1);
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
-}
-
-static int __init rbtx4927_wdt_init(void)
-{
- return txx9_wdt_init(TX4927_TMR_REG(2) & 0xfffffffffULL);
+ platform_device_register_simple("ne", -1, res, ARRAY_SIZE(res));
}
static void __init rbtx4927_device_init(void)
{
toshiba_rbtx4927_rtc_init();
rbtx4927_ne_init();
- rbtx4927_wdt_init();
+ tx4927_wdt_init();
}
struct txx9_board_vec rbtx4927_vec __initdata = {
*/
/*
-IRQ Device
-
-16 TX4938-CP0/00 Software 0
-17 TX4938-CP0/01 Software 1
-18 TX4938-CP0/02 Cascade TX4938-CP0
-19 TX4938-CP0/03 Multiplexed -- do not use
-20 TX4938-CP0/04 Multiplexed -- do not use
-21 TX4938-CP0/05 Multiplexed -- do not use
-22 TX4938-CP0/06 Multiplexed -- do not use
-23 TX4938-CP0/07 CPU TIMER
-
-24 TX4938-PIC/00
-25 TX4938-PIC/01
-26 TX4938-PIC/02 Cascade RBTX4938-IOC
-27 TX4938-PIC/03 RBTX4938 RTL-8019AS Ethernet
-28 TX4938-PIC/04
-29 TX4938-PIC/05 TX4938 ETH1
-30 TX4938-PIC/06 TX4938 ETH0
-31 TX4938-PIC/07
-32 TX4938-PIC/08 TX4938 SIO 0
-33 TX4938-PIC/09 TX4938 SIO 1
-34 TX4938-PIC/10 TX4938 DMA0
-35 TX4938-PIC/11 TX4938 DMA1
-36 TX4938-PIC/12 TX4938 DMA2
-37 TX4938-PIC/13 TX4938 DMA3
-38 TX4938-PIC/14
-39 TX4938-PIC/15
-40 TX4938-PIC/16 TX4938 PCIC
-41 TX4938-PIC/17 TX4938 TMR0
-42 TX4938-PIC/18 TX4938 TMR1
-43 TX4938-PIC/19 TX4938 TMR2
-44 TX4938-PIC/20
-45 TX4938-PIC/21
-46 TX4938-PIC/22 TX4938 PCIERR
-47 TX4938-PIC/23
-48 TX4938-PIC/24
-49 TX4938-PIC/25
-50 TX4938-PIC/26
-51 TX4938-PIC/27
-52 TX4938-PIC/28
-53 TX4938-PIC/29
-54 TX4938-PIC/30
-55 TX4938-PIC/31 TX4938 SPI
-
-56 RBTX4938-IOC/00 PCI-D
-57 RBTX4938-IOC/01 PCI-C
-58 RBTX4938-IOC/02 PCI-B
-59 RBTX4938-IOC/03 PCI-A
-60 RBTX4938-IOC/04 RTC
-61 RBTX4938-IOC/05 ATA
-62 RBTX4938-IOC/06 MODEM
-63 RBTX4938-IOC/07 SWINT
-*/
+ * MIPS_CPU_IRQ_BASE+00 Software 0
+ * MIPS_CPU_IRQ_BASE+01 Software 1
+ * MIPS_CPU_IRQ_BASE+02 Cascade TX4938-CP0
+ * MIPS_CPU_IRQ_BASE+03 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+04 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+05 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+06 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+07 CPU TIMER
+ *
+ * TXX9_IRQ_BASE+00
+ * TXX9_IRQ_BASE+01
+ * TXX9_IRQ_BASE+02 Cascade RBTX4938-IOC
+ * TXX9_IRQ_BASE+03 RBTX4938 RTL-8019AS Ethernet
+ * TXX9_IRQ_BASE+04
+ * TXX9_IRQ_BASE+05 TX4938 ETH1
+ * TXX9_IRQ_BASE+06 TX4938 ETH0
+ * TXX9_IRQ_BASE+07
+ * TXX9_IRQ_BASE+08 TX4938 SIO 0
+ * TXX9_IRQ_BASE+09 TX4938 SIO 1
+ * TXX9_IRQ_BASE+10 TX4938 DMA0
+ * TXX9_IRQ_BASE+11 TX4938 DMA1
+ * TXX9_IRQ_BASE+12 TX4938 DMA2
+ * TXX9_IRQ_BASE+13 TX4938 DMA3
+ * TXX9_IRQ_BASE+14
+ * TXX9_IRQ_BASE+15
+ * TXX9_IRQ_BASE+16 TX4938 PCIC
+ * TXX9_IRQ_BASE+17 TX4938 TMR0
+ * TXX9_IRQ_BASE+18 TX4938 TMR1
+ * TXX9_IRQ_BASE+19 TX4938 TMR2
+ * TXX9_IRQ_BASE+20
+ * TXX9_IRQ_BASE+21
+ * TXX9_IRQ_BASE+22 TX4938 PCIERR
+ * TXX9_IRQ_BASE+23
+ * TXX9_IRQ_BASE+24
+ * TXX9_IRQ_BASE+25
+ * TXX9_IRQ_BASE+26
+ * TXX9_IRQ_BASE+27
+ * TXX9_IRQ_BASE+28
+ * TXX9_IRQ_BASE+29
+ * TXX9_IRQ_BASE+30
+ * TXX9_IRQ_BASE+31 TX4938 SPI
+ *
+ * RBTX4938_IRQ_IOC+00 PCI-D
+ * RBTX4938_IRQ_IOC+01 PCI-C
+ * RBTX4938_IRQ_IOC+02 PCI-B
+ * RBTX4938_IRQ_IOC+03 PCI-A
+ * RBTX4938_IRQ_IOC+04 RTC
+ * RBTX4938_IRQ_IOC+05 ATA
+ * RBTX4938_IRQ_IOC+06 MODEM
+ * RBTX4938_IRQ_IOC+07 SWINT
+ */
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mipsregs.h>
return sw_irq;
}
-/**********************************************************************************/
-/* Functions for ioc */
-/**********************************************************************************/
static void __init
toshiba_rbtx4938_irq_ioc_init(void)
{
prom_init_cmdline();
#endif
add_memory_region(0, tx4938_get_mem_size(), BOOT_MEM_RAM);
+ txx9_sio_putchar_init(TX4938_SIO_REG(0) & 0xfffffffffULL);
}
#include <linux/types.h>
#include <linux/ioport.h>
#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/console.h>
-#include <linux/pm.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <asm/txx9/spi.h>
#include <asm/txx9pio.h>
-static void rbtx4938_machine_halt(void)
-{
- printk(KERN_NOTICE "System Halted\n");
- local_irq_disable();
-
- while (1)
- __asm__(".set\tmips3\n\t"
- "wait\n\t"
- ".set\tmips0");
-}
-
-static void rbtx4938_machine_power_off(void)
-{
- rbtx4938_machine_halt();
- /* no return */
-}
-
static void rbtx4938_machine_restart(char *command)
{
local_irq_disable();
-
- printk("Rebooting...");
writeb(1, rbtx4938_softresetlock_addr);
writeb(1, rbtx4938_sfvol_addr);
writeb(1, rbtx4938_softreset_addr);
- while(1)
- ;
+ /* fallback */
+ (*_machine_halt)();
}
static void __init rbtx4938_pci_setup(void)
register_pci_controller(c);
tx4927_pcic_setup(tx4938_pcic1ptr, c, 0);
}
+ tx4938_setup_pcierr_irq();
#endif /* CONFIG_PCI */
}
if (sum)
printk(KERN_WARNING "seeprom: bad checksum.\n");
}
- for (i = 0; i < 2; i++) {
- unsigned int id =
- TXX9_IRQ_BASE + (i ? TX4938_IR_ETH1 : TX4938_IR_ETH0);
- struct platform_device *pdev;
- if (!(__raw_readq(&tx4938_ccfgptr->pcfg) &
- (i ? TX4938_PCFG_ETH1_SEL : TX4938_PCFG_ETH0_SEL)))
- continue;
- pdev = platform_device_alloc("tc35815-mac", id);
- if (!pdev ||
- platform_device_add_data(pdev, &dat[4 + 6 * i], 6) ||
- platform_device_add(pdev))
- platform_device_put(pdev);
- }
+ tx4938_ethaddr_init(&dat[4], &dat[4 + 6]);
#endif /* CONFIG_PCI */
return 0;
}
#ifdef CONFIG_PCI
txx9_alloc_pci_controller(&txx9_primary_pcic, 0, 0, 0, 0);
+ txx9_board_pcibios_setup = tx4927_pcibios_setup;
#else
set_io_port_base(RBTX4938_ETHER_BASE);
#endif
- tx4938_setup_serial();
+ tx4938_sio_init(7372800, 0);
#ifdef CONFIG_SERIAL_TXX9_CONSOLE
- argptr = prom_getcmdline();
- if (strstr(argptr, "console=") == NULL) {
- strcat(argptr, " console=ttyS0,38400");
- }
+ argptr = prom_getcmdline();
+ if (!strstr(argptr, "console="))
+ strcat(argptr, " console=ttyS0,38400");
#endif
#ifdef CONFIG_TOSHIBA_RBTX4938_MPLEX_PIO58_61
- printk("PIOSEL: disabling both ata and nand selection\n");
- local_irq_disable();
+ printk(KERN_INFO "PIOSEL: disabling both ata and nand selection\n");
txx9_clear64(&tx4938_ccfgptr->pcfg,
TX4938_PCFG_NDF_SEL | TX4938_PCFG_ATA_SEL);
#endif
#ifdef CONFIG_TOSHIBA_RBTX4938_MPLEX_NAND
- printk("PIOSEL: enabling nand selection\n");
+ printk(KERN_INFO "PIOSEL: enabling nand selection\n");
txx9_set64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_NDF_SEL);
txx9_clear64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_ATA_SEL);
#endif
#ifdef CONFIG_TOSHIBA_RBTX4938_MPLEX_ATA
- printk("PIOSEL: enabling ata selection\n");
+ printk(KERN_INFO "PIOSEL: enabling ata selection\n");
txx9_set64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_ATA_SEL);
txx9_clear64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_NDF_SEL);
#endif
-#ifdef CONFIG_IP_PNP
- argptr = prom_getcmdline();
- if (strstr(argptr, "ip=") == NULL) {
- strcat(argptr, " ip=any");
- }
-#endif
-
-
-#ifdef CONFIG_FB
- {
- conswitchp = &dummy_con;
- }
-#endif
-
rbtx4938_spi_setup();
pcfg = ____raw_readq(&tx4938_ccfgptr->pcfg); /* updated */
/* fixup piosel */
rbtx4938_fpga_resource.end = CPHYSADDR(RBTX4938_FPGA_REG_ADDR) + 0xffff;
rbtx4938_fpga_resource.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
if (request_resource(&txx9_ce_res[2], &rbtx4938_fpga_resource))
- printk("request resource for fpga failed\n");
+ printk(KERN_ERR "request resource for fpga failed\n");
_machine_restart = rbtx4938_machine_restart;
- _machine_halt = rbtx4938_machine_halt;
- pm_power_off = rbtx4938_machine_power_off;
writeb(0xff, rbtx4938_led_addr);
printk(KERN_INFO "RBTX4938 --- FPGA(Rev %02x) DIPSW:%02x,%02x\n",
readb(rbtx4938_dipsw_addr), readb(rbtx4938_bdipsw_addr));
}
-static int __init rbtx4938_ne_init(void)
+static void __init rbtx4938_ne_init(void)
{
struct resource res[] = {
{
.flags = IORESOURCE_IRQ,
}
};
- struct platform_device *dev =
- platform_device_register_simple("ne", -1,
- res, ARRAY_SIZE(res));
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
+ platform_device_register_simple("ne", -1, res, ARRAY_SIZE(res));
}
static DEFINE_SPINLOCK(rbtx4938_spi_gpio_lock);
.ngpio = 3,
};
-/* SPI support */
-
-static void __init txx9_spi_init(unsigned long base, int irq)
-{
- struct resource res[] = {
- {
- .start = base,
- .end = base + 0x20 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = irq,
- .flags = IORESOURCE_IRQ,
- },
- };
- platform_device_register_simple("spi_txx9", 0,
- res, ARRAY_SIZE(res));
-}
-
static int __init rbtx4938_spi_init(void)
{
struct spi_board_info srtc_info = {
gpio_direction_output(16 + SEEPROM2_CS, 1);
gpio_request(16 + SEEPROM3_CS, "seeprom3");
gpio_direction_output(16 + SEEPROM3_CS, 1);
- txx9_spi_init(TX4938_SPI_REG & 0xfffffffffULL, RBTX4938_IRQ_IRC_SPI);
+ tx4938_spi_init(0);
return 0;
}
rbtx4938_spi_init();
}
-/* Watchdog support */
-
-static int __init txx9_wdt_init(unsigned long base)
-{
- struct resource res = {
- .start = base,
- .end = base + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- };
- struct platform_device *dev =
- platform_device_register_simple("txx9wdt", -1, &res, 1);
- return IS_ERR(dev) ? PTR_ERR(dev) : 0;
-}
-
-static int __init rbtx4938_wdt_init(void)
-{
- return txx9_wdt_init(TX4938_TMR_REG(2) & 0xfffffffffULL);
-}
-
static void __init rbtx4938_device_init(void)
{
rbtx4938_ethaddr_init();
rbtx4938_ne_init();
- rbtx4938_wdt_init();
+ tx4938_wdt_init();
}
struct txx9_board_vec rbtx4938_vec __initdata = {
.long sys_fallocate /* 325 */
.long sys_timerfd_settime
.long sys_timerfd_gettime
+ .long sys_signalfd4
+ .long sys_eventfd2
+ .long sys_epoll_create1 /* 330 */
+ .long sys_dup3
+ .long sys_pipe2
+ .long sys_inotify_init1
nr_syscalls=(.-sys_call_table)/4
#include <linux/fs.h>
#include <linux/string.h>
#include <linux/kernel.h>
+#include <linux/bug.h>
#if 0
#define DEBUGP printk
const Elf_Shdr *sechdrs,
struct module *me)
{
- return 0;
+ return module_bug_finalize(hdr, sechdrs, me);
}
/*
*/
void module_arch_cleanup(struct module *mod)
{
+ module_bug_cleanup(mod);
}
bool
default y
+config HAVE_GET_USER_PAGES_FAST
+ def_bool PPC64
+
config HAVE_SETUP_PER_CPU_AREA
def_bool PPC64
config VIRQ_DEBUG
bool "Expose hardware/virtual IRQ mapping via debugfs"
- depends on DEBUG_FS && PPC_MERGE
+ depends on DEBUG_FS
help
This option will show the mapping relationship between hardware irq
numbers and virtual irq numbers. The mapping is exposed via debugfs
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <132000000>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>; // from bootloader
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>; // from bootloader
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <264000000>;
};
crypto@30000 {
- compatible = "fsl,sec2-crypto";
+ compatible = "fsl,sec2.0";
reg = <0x30000 0x10000>;
- interrupts = <11 8>;
+ interrupts = <11 0x8>;
interrupt-parent = <&ipic>;
- num-channels = <4>;
- channel-fifo-len = <24>;
- exec-units-mask = <0x7e>;
- /*
- * desc mask is for rev1.x, we need runtime fixup
- * for >=2.x
- */
- descriptor-types-mask = <0x1010ebf>;
+ fsl,num-channels = <4>;
+ fsl,channel-fifo-len = <24>;
+ fsl,exec-units-mask = <0x7e>;
+ fsl,descriptor-types-mask = <0x01010ebf>;
};
ipic: interrupt-controller@700 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xffe00000 0x100000>;
reg = <0xffe00000 0x1000>;
bus-frequency = <0>; // Filled out by uboot.
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x100000>; // CCSRBAR 1M
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x1000>; // CCSRBAR 1M
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x1000>; // CCSRBAR 1M
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x1000>; // CCSRBAR
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x1000>; // CCSRBAR 1M
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x200>;
bus-frequency = <330000000>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x100000>;
reg = <0xe0000000 0x1000>;
bus-frequency = <0>;
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
+ compatible = "simple-bus";
ranges = <0x0 0xffe00000 0x100000>;
reg = <0xffe00000 0x1000>; // CCSRBAR & soc regs, remove once parse code for immrbase fixed
bus-frequency = <0>; // Filled out by uboot.
fsl,has-rstcr;
};
+ wdt@e4000 {
+ compatible = "fsl,mpc8610-wdt";
+ reg = <0xe4000 0x100>;
+ };
+
i2s@16000 {
compatible = "fsl,mpc8610-ssi";
cell-index = <0>;
/*
* Low-level I/O routines.
*
- * Copied from <file:include/asm-powerpc/io.h> (which has no copyright)
+ * Copied from <file:arch/powerpc/include/asm/io.h> (which has no copyright)
*/
static inline int in_8(const volatile unsigned char *addr)
{
#include <linux/compiler.h>
#include <linux/types.h>
+#include <linux/of.h>
/* Opcodes common to CPM1 and CPM2
*/
dma_addr_t cpm_muram_dma(void __iomem *addr);
int cpm_command(u32 command, u8 opcode);
+int cpm2_gpiochip_add32(struct device_node *np);
+
#endif
#include <asm/immap_cpm2.h>
#include <asm/cpm.h>
+#include <sysdev/fsl_soc.h>
#ifdef CONFIG_PPC_85xx
#define CPM_MAP_ADDR (get_immrbase() + 0x80000)
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
-extern void cpm_setbrg(uint brg, uint rate);
-extern void cpm2_fastbrg(uint brg, uint rate, int div16);
extern void cpm2_reset(void);
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST ((uint)0x00020000)
+#define CPM_BRG_EN ((uint)0x00010000)
+#define CPM_BRG_EXTC_INT ((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
+#define CPM_BRG_ATB ((uint)0x00002000)
+#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
+#define CPM_BRG_DIV16 ((uint)0x00000001)
+
+#define CPM2_BRG_INT_CLK (get_brgfreq())
+#define CPM2_BRG_UART_CLK (CPM2_BRG_INT_CLK/16)
+
+extern void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src);
+
+/* This function is used by UARTS, or anything else that uses a 16x
+ * oversampled clock.
+ */
+static inline void cpm_setbrg(uint brg, uint rate)
+{
+ __cpm2_setbrg(brg, rate, CPM2_BRG_UART_CLK, 0, CPM_BRG_EXTC_INT);
+}
+
+/* This function is used to set high speed synchronous baud rate
+ * clocks.
+ */
+static inline void cpm2_fastbrg(uint brg, uint rate, int div16)
+{
+ __cpm2_setbrg(brg, rate, CPM2_BRG_INT_CLK, div16, CPM_BRG_EXTC_INT);
+}
+
/* Function code bits, usually generic to devices.
*/
#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */
#define SMCM_TX ((unsigned char)0x02)
#define SMCM_RX ((unsigned char)0x01)
-/* Baud rate generators.
-*/
-#define CPM_BRG_RST ((uint)0x00020000)
-#define CPM_BRG_EN ((uint)0x00010000)
-#define CPM_BRG_EXTC_INT ((uint)0x00000000)
-#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000)
-#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000)
-#define CPM_BRG_ATB ((uint)0x00002000)
-#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
-#define CPM_BRG_DIV16 ((uint)0x00000001)
-
/* SCCs.
*/
#define SCC_GSMRH_IRP ((uint)0x00040000)
#endif /* defined(CONFIG_PPC_DCR_NATIVE) && defined(CONFIG_PPC_DCR_MMIO) */
/*
- * On CONFIG_PPC_MERGE, we have additional helpers to read the DCR
- * base from the device-tree
+ * additional helpers to read the DCR * base from the device-tree
*/
-#ifdef CONFIG_PPC_MERGE
struct device_node;
extern unsigned int dcr_resource_start(struct device_node *np,
unsigned int index);
extern unsigned int dcr_resource_len(struct device_node *np,
unsigned int index);
-#endif /* CONFIG_PPC_MERGE */
-
#endif /* CONFIG_PPC_DCR */
#endif /* __ASSEMBLY__ */
#endif /* __KERNEL__ */
#include <linux/irq.h>
-#ifdef CONFIG_PPC_MERGE
extern void i8259_init(struct device_node *node, unsigned long intack_addr);
extern unsigned int i8259_irq(void);
extern struct irq_host *i8259_get_host(void);
-#else
-extern void i8259_init(unsigned long intack_addr, int offset);
-extern int i8259_irq(void);
-#endif
#endif /* __KERNEL__ */
#endif /* _ASM_POWERPC_I8259_H */
#define __ide_mm_outsl(p, a, c) writesl((void __iomem *)(p), (a), (c))
#ifndef __powerpc64__
-#include <linux/hdreg.h>
#include <linux/ioport.h>
/* FIXME: use ide_platform host driver */
/*
- * include/asm-powerpc/immap_qe.h
- *
* QUICC Engine (QE) Internal Memory Map.
* The Internal Memory Map for devices with QE on them. This
* is the superset of all QE devices (8360, etc.).
/*
- * include/asm-powerpc/ipic.h
- *
* IPIC external definitions and structure.
*
* Maintainer: Kumar Gala <galak@kernel.crashing.org>
extern u32 ipic_get_mcp_status(void);
extern void ipic_clear_mcp_status(u32 mask);
-#ifdef CONFIG_PPC_MERGE
extern struct ipic * ipic_init(struct device_node *node, unsigned int flags);
extern unsigned int ipic_get_irq(void);
-#else
-extern void ipic_init(phys_addr_t phys_addr, unsigned int flags,
- unsigned int irq_offset,
- unsigned char *senses, unsigned int senses_count);
-extern int ipic_get_irq(void);
-#endif
#endif /* __ASM_IPIC_H__ */
#endif /* __KERNEL__ */
extern atomic_t ppc_n_lost_interrupts;
-#ifdef CONFIG_PPC_MERGE
-
/* This number is used when no interrupt has been assigned */
#define NO_IRQ (0)
return irq;
}
-
-#else /* CONFIG_PPC_MERGE */
-
-/* This number is used when no interrupt has been assigned */
-#define NO_IRQ (-1)
-#define NO_IRQ_IGNORE (-2)
-
-
-/*
- * These constants are used for passing information about interrupt
- * signal polarity and level/edge sensing to the low-level PIC chip
- * drivers.
- */
-#define IRQ_SENSE_MASK 0x1
-#define IRQ_SENSE_LEVEL 0x1 /* interrupt on active level */
-#define IRQ_SENSE_EDGE 0x0 /* interrupt triggered by edge */
-
-#define IRQ_POLARITY_MASK 0x2
-#define IRQ_POLARITY_POSITIVE 0x2 /* high level or low->high edge */
-#define IRQ_POLARITY_NEGATIVE 0x0 /* low level or high->low edge */
-
-
-#if defined(CONFIG_40x)
-#include <asm/ibm4xx.h>
-
-#ifndef NR_BOARD_IRQS
-#define NR_BOARD_IRQS 0
-#endif
-
-#ifndef UIC_WIDTH /* Number of interrupts per device */
-#define UIC_WIDTH 32
-#endif
-
-#ifndef NR_UICS /* number of UIC devices */
-#define NR_UICS 1
-#endif
-
-#if defined (CONFIG_403)
-/*
- * The PowerPC 403 cores' Asynchronous Interrupt Controller (AIC) has
- * 32 possible interrupts, a majority of which are not implemented on
- * all cores. There are six configurable, external interrupt pins and
- * there are eight internal interrupts for the on-chip serial port
- * (SPU), DMA controller, and JTAG controller.
- *
- */
-
-#define NR_AIC_IRQS 32
-#define NR_IRQS (NR_AIC_IRQS + NR_BOARD_IRQS)
-
-#elif !defined (CONFIG_403)
-
-/*
- * The PowerPC 405 cores' Universal Interrupt Controller (UIC) has 32
- * possible interrupts as well. There are seven, configurable external
- * interrupt pins and there are 17 internal interrupts for the on-chip
- * serial port, DMA controller, on-chip Ethernet controller, PCI, etc.
- *
- */
-
-
-#define NR_UIC_IRQS UIC_WIDTH
-#define NR_IRQS ((NR_UIC_IRQS * NR_UICS) + NR_BOARD_IRQS)
-#endif
-
-#elif defined(CONFIG_44x)
-#include <asm/ibm44x.h>
-
-#define NR_UIC_IRQS 32
-#define NR_IRQS ((NR_UIC_IRQS * NR_UICS) + NR_BOARD_IRQS)
-
-#elif defined(CONFIG_8xx)
-
-/* Now include the board configuration specific associations.
-*/
-#include <asm/mpc8xx.h>
-
-/* The MPC8xx cores have 16 possible interrupts. There are eight
- * possible level sensitive interrupts assigned and generated internally
- * from such devices as CPM, PCMCIA, RTC, PIT, TimeBase and Decrementer.
- * There are eight external interrupts (IRQs) that can be configured
- * as either level or edge sensitive.
- *
- * On some implementations, there is also the possibility of an 8259
- * through the PCI and PCI-ISA bridges.
- *
- * We are "flattening" the interrupt vectors of the cascaded CPM
- * and 8259 interrupt controllers so that we can uniquely identify
- * any interrupt source with a single integer.
- */
-#define NR_SIU_INTS 16
-#define NR_CPM_INTS 32
-#ifndef NR_8259_INTS
-#define NR_8259_INTS 0
-#endif
-
-#define SIU_IRQ_OFFSET 0
-#define CPM_IRQ_OFFSET (SIU_IRQ_OFFSET + NR_SIU_INTS)
-#define I8259_IRQ_OFFSET (CPM_IRQ_OFFSET + NR_CPM_INTS)
-
-#define NR_IRQS (NR_SIU_INTS + NR_CPM_INTS + NR_8259_INTS)
-
-/* These values must be zero-based and map 1:1 with the SIU configuration.
- * They are used throughout the 8xx I/O subsystem to generate
- * interrupt masks, flags, and other control patterns. This is why the
- * current kernel assumption of the 8259 as the base controller is such
- * a pain in the butt.
- */
-#define SIU_IRQ0 (0) /* Highest priority */
-#define SIU_LEVEL0 (1)
-#define SIU_IRQ1 (2)
-#define SIU_LEVEL1 (3)
-#define SIU_IRQ2 (4)
-#define SIU_LEVEL2 (5)
-#define SIU_IRQ3 (6)
-#define SIU_LEVEL3 (7)
-#define SIU_IRQ4 (8)
-#define SIU_LEVEL4 (9)
-#define SIU_IRQ5 (10)
-#define SIU_LEVEL5 (11)
-#define SIU_IRQ6 (12)
-#define SIU_LEVEL6 (13)
-#define SIU_IRQ7 (14)
-#define SIU_LEVEL7 (15)
-
-#define MPC8xx_INT_FEC1 SIU_LEVEL1
-#define MPC8xx_INT_FEC2 SIU_LEVEL3
-
-#define MPC8xx_INT_SCC1 (CPM_IRQ_OFFSET + CPMVEC_SCC1)
-#define MPC8xx_INT_SCC2 (CPM_IRQ_OFFSET + CPMVEC_SCC2)
-#define MPC8xx_INT_SCC3 (CPM_IRQ_OFFSET + CPMVEC_SCC3)
-#define MPC8xx_INT_SCC4 (CPM_IRQ_OFFSET + CPMVEC_SCC4)
-#define MPC8xx_INT_SMC1 (CPM_IRQ_OFFSET + CPMVEC_SMC1)
-#define MPC8xx_INT_SMC2 (CPM_IRQ_OFFSET + CPMVEC_SMC2)
-
-/* The internal interrupts we can configure as we see fit.
- * My personal preference is CPM at level 2, which puts it above the
- * MBX PCI/ISA/IDE interrupts.
- */
-#ifndef PIT_INTERRUPT
-#define PIT_INTERRUPT SIU_LEVEL0
-#endif
-#ifndef CPM_INTERRUPT
-#define CPM_INTERRUPT SIU_LEVEL2
-#endif
-#ifndef PCMCIA_INTERRUPT
-#define PCMCIA_INTERRUPT SIU_LEVEL6
-#endif
-#ifndef DEC_INTERRUPT
-#define DEC_INTERRUPT SIU_LEVEL7
-#endif
-
-/* Some internal interrupt registers use an 8-bit mask for the interrupt
- * level instead of a number.
- */
-#define mk_int_int_mask(IL) (1 << (7 - (IL/2)))
-
-#else /* CONFIG_40x + CONFIG_8xx */
-/*
- * this is the # irq's for all ppc arch's (pmac/chrp/prep)
- * so it is the max of them all
- */
-#define NR_IRQS 256
-#define __DO_IRQ_CANON 1
-
-#ifndef CONFIG_8260
-
-#define NUM_8259_INTERRUPTS 16
-
-#else /* CONFIG_8260 */
-
-/* The 8260 has an internal interrupt controller with a maximum of
- * 64 IRQs. We will use NR_IRQs from above since it is large enough.
- * Don't be confused by the 8260 documentation where they list an
- * "interrupt number" and "interrupt vector". We are only interested
- * in the interrupt vector. There are "reserved" holes where the
- * vector number increases, but the interrupt number in the table does not.
- * (Document errata updates have fixed this...make sure you have up to
- * date processor documentation -- Dan).
- */
-
-#ifndef CPM_IRQ_OFFSET
-#define CPM_IRQ_OFFSET 0
-#endif
-
-#define NR_CPM_INTS 64
-
-#define SIU_INT_ERROR ((uint)0x00 + CPM_IRQ_OFFSET)
-#define SIU_INT_I2C ((uint)0x01 + CPM_IRQ_OFFSET)
-#define SIU_INT_SPI ((uint)0x02 + CPM_IRQ_OFFSET)
-#define SIU_INT_RISC ((uint)0x03 + CPM_IRQ_OFFSET)
-#define SIU_INT_SMC1 ((uint)0x04 + CPM_IRQ_OFFSET)
-#define SIU_INT_SMC2 ((uint)0x05 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA1 ((uint)0x06 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA2 ((uint)0x07 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA3 ((uint)0x08 + CPM_IRQ_OFFSET)
-#define SIU_INT_IDMA4 ((uint)0x09 + CPM_IRQ_OFFSET)
-#define SIU_INT_SDMA ((uint)0x0a + CPM_IRQ_OFFSET)
-#define SIU_INT_USB ((uint)0x0b + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER1 ((uint)0x0c + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER2 ((uint)0x0d + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER3 ((uint)0x0e + CPM_IRQ_OFFSET)
-#define SIU_INT_TIMER4 ((uint)0x0f + CPM_IRQ_OFFSET)
-#define SIU_INT_TMCNT ((uint)0x10 + CPM_IRQ_OFFSET)
-#define SIU_INT_PIT ((uint)0x11 + CPM_IRQ_OFFSET)
-#define SIU_INT_PCI ((uint)0x12 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ1 ((uint)0x13 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ2 ((uint)0x14 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ3 ((uint)0x15 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ4 ((uint)0x16 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ5 ((uint)0x17 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ6 ((uint)0x18 + CPM_IRQ_OFFSET)
-#define SIU_INT_IRQ7 ((uint)0x19 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC1 ((uint)0x20 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC2 ((uint)0x21 + CPM_IRQ_OFFSET)
-#define SIU_INT_FCC3 ((uint)0x22 + CPM_IRQ_OFFSET)
-#define SIU_INT_MCC1 ((uint)0x24 + CPM_IRQ_OFFSET)
-#define SIU_INT_MCC2 ((uint)0x25 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC1 ((uint)0x28 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC2 ((uint)0x29 + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC3 ((uint)0x2a + CPM_IRQ_OFFSET)
-#define SIU_INT_SCC4 ((uint)0x2b + CPM_IRQ_OFFSET)
-#define SIU_INT_PC15 ((uint)0x30 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC14 ((uint)0x31 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC13 ((uint)0x32 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC12 ((uint)0x33 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC11 ((uint)0x34 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC10 ((uint)0x35 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC9 ((uint)0x36 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC8 ((uint)0x37 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC7 ((uint)0x38 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC6 ((uint)0x39 + CPM_IRQ_OFFSET)
-#define SIU_INT_PC5 ((uint)0x3a + CPM_IRQ_OFFSET)
-#define SIU_INT_PC4 ((uint)0x3b + CPM_IRQ_OFFSET)
-#define SIU_INT_PC3 ((uint)0x3c + CPM_IRQ_OFFSET)
-#define SIU_INT_PC2 ((uint)0x3d + CPM_IRQ_OFFSET)
-#define SIU_INT_PC1 ((uint)0x3e + CPM_IRQ_OFFSET)
-#define SIU_INT_PC0 ((uint)0x3f + CPM_IRQ_OFFSET)
-
-#endif /* CONFIG_8260 */
-
-#endif /* Whatever way too big #ifdef */
-
-#define NR_MASK_WORDS ((NR_IRQS + 31) / 32)
-/* pedantic: these are long because they are used with set_bit --RR */
-extern unsigned long ppc_cached_irq_mask[NR_MASK_WORDS];
-
-/*
- * Because many systems have two overlapping names spaces for
- * interrupts (ISA and XICS for example), and the ISA interrupts
- * have historically not been easy to renumber, we allow ISA
- * interrupts to take values 0 - 15, and shift up the remaining
- * interrupts by 0x10.
- */
-#define NUM_ISA_INTERRUPTS 0x10
-extern int __irq_offset_value;
-
-static inline int irq_offset_up(int irq)
-{
- return(irq + __irq_offset_value);
-}
-
-static inline int irq_offset_down(int irq)
-{
- return(irq - __irq_offset_value);
-}
-
-static inline int irq_offset_value(void)
-{
- return __irq_offset_value;
-}
-
-#ifdef __DO_IRQ_CANON
-extern int ppc_do_canonicalize_irqs;
-#else
-#define ppc_do_canonicalize_irqs 0
-#endif
-
-static __inline__ int irq_canonicalize(int irq)
-{
- if (ppc_do_canonicalize_irqs && irq == 2)
- irq = 9;
- return irq;
-}
-#endif /* CONFIG_PPC_MERGE */
-
extern int distribute_irqs;
struct irqaction;
/*
- * include/asm-powerpc/irqflags.h
- *
* IRQ flags handling
*/
#ifndef _ASM_IRQFLAGS_H
/*
* Get definitions for raw_local_save_flags(x), etc.
*/
-#include <asm-powerpc/hw_irq.h>
+#include <asm/hw_irq.h>
#else
#ifdef CONFIG_TRACE_IRQFLAGS
/*
- * include/asm-powerpc/kgdb.h
- *
* The PowerPC (32/64) specific defines / externs for KGDB. Based on
* the previous 32bit and 64bit specific files, which had the following
* copyrights:
/*
- * include/asm-powerpc/paca.h
- *
* This control block defines the PACA which defines the processor
* specific data for each logical processor on the system.
* There are some pointers defined that are utilized by PLIC.
#define _PAGE_WRENABLE (_PAGE_RW | _PAGE_DIRTY)
-/* __pgprot defined in asm-powerpc/page.h */
+/* __pgprot defined in arch/powerpc/incliude/asm/page.h */
#define PAGE_NONE __pgprot(_PAGE_PRESENT | _PAGE_ACCESSED)
#define PAGE_SHARED __pgprot(_PAGE_BASE | _PAGE_RW | _PAGE_USER)
return pt;
}
+pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long address);
+
#endif /* __ASSEMBLY__ */
#endif /* _ASM_POWERPC_PGTABLE_PPC64_H_ */
/*
- * include/asm-powerpc/qe_ic.h
- *
* Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved.
*
* Authors: Shlomi Gridish <gridish@freescale.com>
#ifdef __KERNEL__
/*
- * include/asm-powerpc/rwsem.h: R/W semaphores for PPC using the stuff
- * in lib/rwsem.c. Adapted largely from include/asm-i386/rwsem.h
+ * R/W semaphores for PPC using the stuff in lib/rwsem.c.
+ * Adapted largely from include/asm-i386/rwsem.h
* by Paul Mackerras <paulus@samba.org>.
*/
/*
- * include/asm-powerpc/ucc_fast.h
- *
* Internal header file for UCC FAST unit routines.
*
* Copyright (C) 2006 Freescale Semicondutor, Inc. All rights reserved.
/*
- * include/asm-powerpc/uic.h
- *
* IBM PPC4xx UIC external definitions and structure.
*
* Maintainer: David Gibson <dwg@au1.ibm.com>
obj-$(CONFIG_MODULES) += module.o module_$(CONFIG_WORD_SIZE).o
obj-$(CONFIG_44x) += cpu_setup_44x.o
-ifeq ($(CONFIG_PPC_MERGE),y)
-
extra-$(CONFIG_PPC_STD_MMU) := head_32.o
extra-$(CONFIG_PPC64) := head_64.o
extra-$(CONFIG_40x) := head_40x.o
obj-y += iomap.o
endif
-else
-# stuff used from here for ARCH=ppc
-smpobj-$(CONFIG_SMP) += smp.o
-
-endif
-
obj-$(CONFIG_PPC64) += $(obj64-y)
extra-$(CONFIG_PPC_FPU) += fpu.o
systbl_chk: $(src)/systbl_chk.sh $(obj)/systbl_chk.i
$(call cmd,systbl_chk)
-
-ifeq ($(CONFIG_PPC_MERGE),y)
-
$(obj)/built-in.o: prom_init_check
quiet_cmd_prom_init_check = CALL $<
prom_init_check: $(src)/prom_init_check.sh $(obj)/prom_init.o
$(call cmd,prom_init_check)
-endif
-
-
clean-files := vmlinux.lds
_GLOBAL(__setup_cpu_440spe)
b __fixup_440A_mcheck
- /* Temporary fixup for arch/ppc until we kill the whole thing */
-#ifndef CONFIG_PPC_MERGE
-_GLOBAL(__fixup_440A_mcheck)
- blr
-#endif
-
/* enable APU between CPU and FPU */
_GLOBAL(__init_fpu_44x)
mfspr r3,SPRN_CCR0
EXPORT_SYMBOL(__irq_offset_value);
atomic_t ppc_n_lost_interrupts;
-#ifndef CONFIG_PPC_MERGE
-#define NR_MASK_WORDS ((NR_IRQS + 31) / 32)
-unsigned long ppc_cached_irq_mask[NR_MASK_WORDS];
-#endif
-
#ifdef CONFIG_TAU_INT
extern int tau_initialized;
extern int tau_interrupts(int);
#endif
#endif /* CONFIG_PPC32 */
-#if defined(CONFIG_SMP) && !defined(CONFIG_PPC_MERGE)
-extern atomic_t ipi_recv;
-extern atomic_t ipi_sent;
-#endif
-
#ifdef CONFIG_PPC64
EXPORT_SYMBOL(irq_desc);
skip:
spin_unlock_irqrestore(&desc->lock, flags);
} else if (i == NR_IRQS) {
-#ifdef CONFIG_PPC32
-#ifdef CONFIG_TAU_INT
+#if defined(CONFIG_PPC32) && defined(CONFIG_TAU_INT)
if (tau_initialized){
seq_puts(p, "TAU: ");
for_each_online_cpu(j)
seq_printf(p, "%10u ", tau_interrupts(j));
seq_puts(p, " PowerPC Thermal Assist (cpu temp)\n");
}
-#endif
-#if defined(CONFIG_SMP) && !defined(CONFIG_PPC_MERGE)
- /* should this be per processor send/receive? */
- seq_printf(p, "IPI (recv/sent): %10u/%u\n",
- atomic_read(&ipi_recv), atomic_read(&ipi_sent));
-#endif
-#endif /* CONFIG_PPC32 */
+#endif /* CONFIG_PPC32 && CONFIG_TAU_INT*/
seq_printf(p, "BAD: %10u\n", ppc_spurious_interrupts);
}
return 0;
* IRQ controller and virtual interrupts
*/
-#ifdef CONFIG_PPC_MERGE
-
static LIST_HEAD(irq_hosts);
static DEFINE_SPINLOCK(irq_big_lock);
static DEFINE_PER_CPU(unsigned int, irq_radix_reader);
__initcall(irq_debugfs_init);
#endif /* CONFIG_VIRQ_DEBUG */
-#endif /* CONFIG_PPC_MERGE */
-
#ifdef CONFIG_PPC64
static int __init setup_noirqdistrib(char *str)
{
retval = -EIO;
} else if (retval == H_PARAMETER) {
retval = -EINVAL;
- } else {
- printk(KERN_WARNING "%s: received unknown hv return code %ld",
- __func__, retval);
- retval = -EIO;
}
return retval;
{
__get_cpu_var(current_dabr) = dabr;
-#ifdef CONFIG_PPC_MERGE /* XXX for now */
if (ppc_md.set_dabr)
return ppc_md.set_dabr(dabr);
-#endif
/* XXX should we have a CPU_FTR_HAS_DABR ? */
#if defined(CONFIG_PPC64) || defined(CONFIG_6xx)
flush_vsx_to_thread(target);
for (i = 0; i < 32 ; i++)
- buf[i] = current->thread.fpr[i][TS_VSRLOWOFFSET];
+ buf[i] = target->thread.fpr[i][TS_VSRLOWOFFSET];
ret = user_regset_copyout(&pos, &count, &kbuf, &ubuf,
buf, 0, 32 * sizeof(double));
ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
buf, 0, 32 * sizeof(double));
for (i = 0; i < 32 ; i++)
- current->thread.fpr[i][TS_VSRLOWOFFSET] = buf[i];
+ target->thread.fpr[i][TS_VSRLOWOFFSET] = buf[i];
return ret;
case PTRACE_GETVSRREGS:
return copy_regset_to_user(child, &user_ppc_native_view,
REGSET_VSX,
- 0, (32 * sizeof(vector128) +
- sizeof(u32)),
+ 0, 32 * sizeof(double),
(void __user *) data);
case PTRACE_SETVSRREGS:
return copy_regset_from_user(child, &user_ppc_native_view,
REGSET_VSX,
- 0, (32 * sizeof(vector128) +
- sizeof(u32)),
+ 0, 32 * sizeof(double),
(const void __user *) data);
#endif
#ifdef CONFIG_SPE
case PTRACE_SETFPREGS:
case PTRACE_GETVRREGS:
case PTRACE_SETVRREGS:
+ case PTRACE_GETVSRREGS:
+ case PTRACE_SETVSRREGS:
case PTRACE_GETREGS64:
case PTRACE_SETREGS64:
case PPC_PTRACE_GETFPREGS:
return 0;
}
-#ifdef CONFIG_PPC_MERGE
arch_initcall(vdso_init);
-#endif
int in_gate_area_no_task(unsigned long addr)
{
EXTRA_CFLAGS += -mno-minimal-toc
endif
-ifeq ($(CONFIG_PPC_MERGE),y)
obj-y := string.o alloc.o \
checksum_$(CONFIG_WORD_SIZE).o
obj-$(CONFIG_PPC32) += div64.o copy_32.o crtsavres.o
obj-$(CONFIG_HAS_IOMEM) += devres.o
-endif
obj-$(CONFIG_PPC64) += copypage_64.o copyuser_64.o \
memcpy_64.o usercopy_64.o mem_64.o string.o
mmu_context_$(CONFIG_WORD_SIZE).o
hash-$(CONFIG_PPC_NATIVE) := hash_native_64.o
obj-$(CONFIG_PPC64) += hash_utils_64.o \
- slb_low.o slb.o stab.o mmap.o $(hash-y)
+ slb_low.o slb.o stab.o \
+ gup.o mmap.o $(hash-y)
obj-$(CONFIG_PPC_STD_MMU_32) += ppc_mmu_32.o
obj-$(CONFIG_PPC_STD_MMU) += hash_low_$(CONFIG_WORD_SIZE).o \
tlb_$(CONFIG_WORD_SIZE).o
--- /dev/null
+/*
+ * Lockless get_user_pages_fast for powerpc
+ *
+ * Copyright (C) 2008 Nick Piggin
+ * Copyright (C) 2008 Novell Inc.
+ */
+#undef DEBUG
+
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/vmstat.h>
+#include <linux/pagemap.h>
+#include <linux/rwsem.h>
+#include <asm/pgtable.h>
+
+/*
+ * The performance critical leaf functions are made noinline otherwise gcc
+ * inlines everything into a single function which results in too much
+ * register pressure.
+ */
+static noinline int gup_pte_range(pmd_t pmd, unsigned long addr,
+ unsigned long end, int write, struct page **pages, int *nr)
+{
+ unsigned long mask, result;
+ pte_t *ptep;
+
+ result = _PAGE_PRESENT|_PAGE_USER;
+ if (write)
+ result |= _PAGE_RW;
+ mask = result | _PAGE_SPECIAL;
+
+ ptep = pte_offset_kernel(&pmd, addr);
+ do {
+ pte_t pte = *ptep;
+ struct page *page;
+
+ if ((pte_val(pte) & mask) != result)
+ return 0;
+ VM_BUG_ON(!pfn_valid(pte_pfn(pte)));
+ page = pte_page(pte);
+ if (!page_cache_get_speculative(page))
+ return 0;
+ if (unlikely(pte != *ptep)) {
+ put_page(page);
+ return 0;
+ }
+ pages[*nr] = page;
+ (*nr)++;
+
+ } while (ptep++, addr += PAGE_SIZE, addr != end);
+
+ return 1;
+}
+
+#ifdef CONFIG_HUGETLB_PAGE
+static noinline int gup_huge_pte(pte_t *ptep, struct hstate *hstate,
+ unsigned long *addr, unsigned long end,
+ int write, struct page **pages, int *nr)
+{
+ unsigned long mask;
+ unsigned long pte_end;
+ struct page *head, *page;
+ pte_t pte;
+ int refs;
+
+ pte_end = (*addr + huge_page_size(hstate)) & huge_page_mask(hstate);
+ if (pte_end < end)
+ end = pte_end;
+
+ pte = *ptep;
+ mask = _PAGE_PRESENT|_PAGE_USER;
+ if (write)
+ mask |= _PAGE_RW;
+ if ((pte_val(pte) & mask) != mask)
+ return 0;
+ /* hugepages are never "special" */
+ VM_BUG_ON(!pfn_valid(pte_pfn(pte)));
+
+ refs = 0;
+ head = pte_page(pte);
+ page = head + ((*addr & ~huge_page_mask(hstate)) >> PAGE_SHIFT);
+ do {
+ VM_BUG_ON(compound_head(page) != head);
+ pages[*nr] = page;
+ (*nr)++;
+ page++;
+ refs++;
+ } while (*addr += PAGE_SIZE, *addr != end);
+
+ if (!page_cache_add_speculative(head, refs)) {
+ *nr -= refs;
+ return 0;
+ }
+ if (unlikely(pte != *ptep)) {
+ /* Could be optimized better */
+ while (*nr) {
+ put_page(page);
+ (*nr)--;
+ }
+ }
+
+ return 1;
+}
+#endif /* CONFIG_HUGETLB_PAGE */
+
+static int gup_pmd_range(pud_t pud, unsigned long addr, unsigned long end,
+ int write, struct page **pages, int *nr)
+{
+ unsigned long next;
+ pmd_t *pmdp;
+
+ pmdp = pmd_offset(&pud, addr);
+ do {
+ pmd_t pmd = *pmdp;
+
+ next = pmd_addr_end(addr, end);
+ if (pmd_none(pmd))
+ return 0;
+ if (!gup_pte_range(pmd, addr, next, write, pages, nr))
+ return 0;
+ } while (pmdp++, addr = next, addr != end);
+
+ return 1;
+}
+
+static int gup_pud_range(pgd_t pgd, unsigned long addr, unsigned long end,
+ int write, struct page **pages, int *nr)
+{
+ unsigned long next;
+ pud_t *pudp;
+
+ pudp = pud_offset(&pgd, addr);
+ do {
+ pud_t pud = *pudp;
+
+ next = pud_addr_end(addr, end);
+ if (pud_none(pud))
+ return 0;
+ if (!gup_pmd_range(pud, addr, next, write, pages, nr))
+ return 0;
+ } while (pudp++, addr = next, addr != end);
+
+ return 1;
+}
+
+int get_user_pages_fast(unsigned long start, int nr_pages, int write,
+ struct page **pages)
+{
+ struct mm_struct *mm = current->mm;
+ unsigned long addr, len, end;
+ unsigned long next;
+ pgd_t *pgdp;
+ int psize, nr = 0;
+ unsigned int shift;
+
+ pr_debug("%s(%lx,%x,%s)\n", __func__, start, nr_pages, write ? "write" : "read");
+
+ start &= PAGE_MASK;
+ addr = start;
+ len = (unsigned long) nr_pages << PAGE_SHIFT;
+ end = start + len;
+
+ if (unlikely(!access_ok(write ? VERIFY_WRITE : VERIFY_READ,
+ start, len)))
+ goto slow_irqon;
+
+ pr_debug(" aligned: %lx .. %lx\n", start, end);
+
+#ifdef CONFIG_HUGETLB_PAGE
+ /* We bail out on slice boundary crossing when hugetlb is
+ * enabled in order to not have to deal with two different
+ * page table formats
+ */
+ if (addr < SLICE_LOW_TOP) {
+ if (end > SLICE_LOW_TOP)
+ goto slow_irqon;
+
+ if (unlikely(GET_LOW_SLICE_INDEX(addr) !=
+ GET_LOW_SLICE_INDEX(end - 1)))
+ goto slow_irqon;
+ } else {
+ if (unlikely(GET_HIGH_SLICE_INDEX(addr) !=
+ GET_HIGH_SLICE_INDEX(end - 1)))
+ goto slow_irqon;
+ }
+#endif /* CONFIG_HUGETLB_PAGE */
+
+ /*
+ * XXX: batch / limit 'nr', to avoid large irq off latency
+ * needs some instrumenting to determine the common sizes used by
+ * important workloads (eg. DB2), and whether limiting the batch size
+ * will decrease performance.
+ *
+ * It seems like we're in the clear for the moment. Direct-IO is
+ * the main guy that batches up lots of get_user_pages, and even
+ * they are limited to 64-at-a-time which is not so many.
+ */
+ /*
+ * This doesn't prevent pagetable teardown, but does prevent
+ * the pagetables from being freed on powerpc.
+ *
+ * So long as we atomically load page table pointers versus teardown,
+ * we can follow the address down to the the page and take a ref on it.
+ */
+ local_irq_disable();
+
+ psize = get_slice_psize(mm, addr);
+ shift = mmu_psize_defs[psize].shift;
+
+#ifdef CONFIG_HUGETLB_PAGE
+ if (unlikely(mmu_huge_psizes[psize])) {
+ pte_t *ptep;
+ unsigned long a = addr;
+ unsigned long sz = ((1UL) << shift);
+ struct hstate *hstate = size_to_hstate(sz);
+
+ BUG_ON(!hstate);
+ /*
+ * XXX: could be optimized to avoid hstate
+ * lookup entirely (just use shift)
+ */
+
+ do {
+ VM_BUG_ON(shift != mmu_psize_defs[get_slice_psize(mm, a)].shift);
+ ptep = huge_pte_offset(mm, a);
+ pr_debug(" %016lx: huge ptep %p\n", a, ptep);
+ if (!ptep || !gup_huge_pte(ptep, hstate, &a, end, write, pages,
+ &nr))
+ goto slow;
+ } while (a != end);
+ } else
+#endif /* CONFIG_HUGETLB_PAGE */
+ {
+ pgdp = pgd_offset(mm, addr);
+ do {
+ pgd_t pgd = *pgdp;
+
+ VM_BUG_ON(shift != mmu_psize_defs[get_slice_psize(mm, addr)].shift);
+ pr_debug(" %016lx: normal pgd %p\n", addr, (void *)pgd);
+ next = pgd_addr_end(addr, end);
+ if (pgd_none(pgd))
+ goto slow;
+ if (!gup_pud_range(pgd, addr, next, write, pages, &nr))
+ goto slow;
+ } while (pgdp++, addr = next, addr != end);
+ }
+ local_irq_enable();
+
+ VM_BUG_ON(nr != (end - start) >> PAGE_SHIFT);
+ return nr;
+
+ {
+ int ret;
+
+slow:
+ local_irq_enable();
+slow_irqon:
+ pr_debug(" slow path ! nr = %d\n", nr);
+
+ /* Try to get the remaining pages with get_user_pages */
+ start += nr << PAGE_SHIFT;
+ pages += nr;
+
+ down_read(&mm->mmap_sem);
+ ret = get_user_pages(current, mm, start,
+ (end - start) >> PAGE_SHIFT, write, 0, pages, NULL);
+ up_read(&mm->mmap_sem);
+
+ /* Have to be a bit careful with return values */
+ if (nr > 0) {
+ if (ret < 0)
+ ret = nr;
+ else
+ ret += nr;
+ }
+
+ return ret;
+ }
+}
#endif /* CONFIG_HIGHMEM */
printk(KERN_DEBUG "Top of RAM: 0x%llx, Total RAM: 0x%lx\n",
- (u64)top_of_ram, total_ram);
+ (unsigned long long)top_of_ram, total_ram);
printk(KERN_DEBUG "Memory hole size: %ldMB\n",
(long int)((top_of_ram - total_ram) >> 20));
memset(max_zone_pfns, 0, sizeof(max_zone_pfns));
Hash_end = (struct hash_pte *) ((unsigned long)Hash + Hash_size);
- printk("Total memory = %ldMB; using %ldkB for hash table (at %p)\n",
- total_memory >> 20, Hash_size >> 10, Hash);
+ printk("Total memory = %lldMB; using %ldkB for hash table (at %p)\n",
+ (unsigned long long)(total_memory >> 20), Hash_size >> 10, Hash);
/*
DEFINE_PER_CPU(struct ppc64_tlb_batch, ppc64_tlb_batch);
/* This is declared as we are using the more or less generic
- * include/asm-powerpc/tlb.h file -- tgall
+ * arch/powerpc/include/asm/tlb.h file -- tgall
*/
DEFINE_PER_CPU(struct mmu_gather, mmu_gathers);
static DEFINE_PER_CPU(struct pte_freelist_batch *, pte_freelist_cur);
#
# Makefile for 52xx based boards
#
-ifeq ($(CONFIG_PPC_MERGE),y)
obj-y += mpc52xx_pic.o mpc52xx_common.o
obj-$(CONFIG_PCI) += mpc52xx_pci.o
-endif
obj-$(CONFIG_PPC_MPC5200_SIMPLE) += mpc5200_simple.o
obj-$(CONFIG_PPC_EFIKA) += efika.o
obj-$(CONFIG_PM) += lite5200_sleep.o lite5200_pm.o
endif
-obj-$(CONFIG_PPC_MPC5200_GPIO) += mpc52xx_gpio.o
\ No newline at end of file
+obj-$(CONFIG_PPC_MPC5200_GPIO) += mpc52xx_gpio.o
static struct of_device_id mpc832x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{ .type = "qe", },
{ .compatible = "fsl,qe", },
{},
static struct of_device_id mpc832x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{ .type = "qe", },
{ .compatible = "fsl,qe", },
{},
static struct of_device_id __initdata mpc834x_itx_ids[] = {
{ .compatible = "fsl,pq2pro-localbus", },
+ { .compatible = "simple-bus", },
{},
};
static struct of_device_id mpc834x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{},
};
static struct of_device_id mpc836x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{ .type = "qe", },
{ .compatible = "fsl,qe", },
{},
static struct __initdata of_device_id sbc834x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{},
};
static struct of_device_id __initdata of_bus_ids[] = {
{ .type = "soc", },
+ { .type = "simple-bus", },
{ .name = "cpm", },
{ .name = "localbus", },
{},
static struct of_device_id __initdata mpc8536_ds_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{},
};
{ .type = "soc", },
{ .name = "cpm", },
{ .name = "localbus", },
+ { .compatible = "simple-bus", },
{},
};
static struct of_device_id __initdata mpc85xxds_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{},
};
static struct of_device_id mpc85xx_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
+ { .compatible = "simple-bus", },
{ .type = "qe", },
{ .compatible = "fsl,qe", },
{},
{ .type = "soc", },
{ .name = "cpm", },
{ .name = "localbus", },
+ { .compatible = "simple-bus", },
{},
};
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/pci-bridge.h>
-#include <asm-powerpc/mpic.h>
+#include <asm/mpic.h>
#include <asm/mpc86xx.h>
#include <asm/cacheflush.h>
If in doubt, say Y here.
+config 8xx_GPIO
+ bool "GPIO API Support"
+ select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
+ help
+ Saying Y here will cause the ports on an MPC8xx processor to be used
+ with the GPIO API. If you say N here, the kernel needs less memory.
+
+ If in doubt, say Y here.
+
config 8xx_CPU6
bool "CPU6 Silicon Errata (860 Pre Rev. C)"
help
select CPM
select PPC_LIB_RHEAP
select PPC_PCI_CHOICE
+ select ARCH_REQUIRE_GPIOLIB
+ select GENERIC_GPIO
help
The CPM2 (Communications Processor Module) is a coprocessor on
embedded CPUs made by Freescale. Selecting this option means that
config CPM
bool
+ select PPC_CLOCK
config OF_RTC
bool
obj-$(CONFIG_FSL_ULI1575) += fsl_uli1575.o
-ifeq ($(CONFIG_PPC_MERGE),y)
obj-$(CONFIG_PPC_PMAC) += powermac/
-else
-ifeq ($(CONFIG_PPC64),y)
-obj-$(CONFIG_PPC_PMAC) += powermac/
-endif
-endif
obj-$(CONFIG_PPC_CHRP) += chrp/
obj-$(CONFIG_40x) += 40x/
obj-$(CONFIG_44x) += 44x/
struct cpufreq_frequency_table *cbe_freqs;
u8 node;
+ /* Should this really be called for CPUFREQ_ADJUST, CPUFREQ_INCOMPATIBLE
+ * and CPUFREQ_NOTIFY policy events?)
+ */
+ if (event == CPUFREQ_START)
+ return 0;
+
cbe_freqs = cpufreq_frequency_get_table(policy->cpu);
node = cbe_cpu_to_node(policy->cpu);
menu "iSeries device drivers"
depends on PPC_ISERIES
-config VIOCONS
- bool "iSeries Virtual Console Support (Obsolete)"
- depends on !HVC_ISERIES
- default n
- help
- This is the old virtual console driver for legacy iSeries.
- You should use the iSeries Hypervisor Virtual Console
- support instead.
-
config VIODASD
tristate "iSeries Virtual I/O disk support"
help
config VIOPATH
bool
- depends on VIOCONS || VIODASD || VIOCD || VIOTAPE || ISERIES_VETH
+ depends on VIODASD || VIOCD || VIOTAPE || ISERIES_VETH
default y
obj-y += pic.o setup.o time.o feature.o pci.o \
sleep.o low_i2c.o cache.o pfunc_core.o \
- pfunc_base.o
+ pfunc_base.o udbg_scc.o udbg_adb.o
obj-$(CONFIG_PMAC_BACKLIGHT) += backlight.o
obj-$(CONFIG_CPU_FREQ_PMAC) += cpufreq_32.o
obj-$(CONFIG_CPU_FREQ_PMAC64) += cpufreq_64.o
obj-$(CONFIG_PPC64) += nvram.o
obj-$(CONFIG_PPC32) += bootx_init.o
obj-$(CONFIG_SMP) += smp.o
-obj-$(CONFIG_PPC_MERGE) += udbg_scc.o udbg_adb.o
obj-$(CONFIG_RTC_DRV_CMOS) += rtc_cmos_setup.o
obj-$(CONFIG_AXON_RAM) += axonram.o
-ifeq ($(CONFIG_PPC_MERGE),y)
obj-$(CONFIG_PPC_INDIRECT_PCI) += indirect_pci.o
obj-$(CONFIG_PPC_I8259) += i8259.o
obj-$(CONFIG_IPIC) += ipic.o
ifeq ($(CONFIG_PCI),y)
obj-$(CONFIG_4xx) += ppc4xx_pci.o
endif
-endif
# Temporary hack until we have migrated to asm-powerpc
ifeq ($(ARCH),powerpc)
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/module.h>
+#include <linux/spinlock.h>
#include <asm/page.h>
#include <asm/pgtable.h>
#include <asm/8xx_immap.h>
#include <asm/fs_pd.h>
+#ifdef CONFIG_8xx_GPIO
+#include <linux/of_gpio.h>
+#endif
+
#define CPM_MAP_SIZE (0x4000)
cpm8xx_t __iomem *cpmp; /* Pointer to comm processor space */
__be16 res[3];
};
-struct cpm_ioport32 {
- __be32 dir, par, sor;
+struct cpm_ioport32b {
+ __be32 dir, par, odr, dat;
+};
+
+struct cpm_ioport32e {
+ __be32 dir, par, sor, odr, dat;
};
static void cpm1_set_pin32(int port, int pin, int flags)
{
- struct cpm_ioport32 __iomem *iop;
+ struct cpm_ioport32e __iomem *iop;
pin = 1 << (31 - pin);
if (port == CPM_PORTB)
- iop = (struct cpm_ioport32 __iomem *)
+ iop = (struct cpm_ioport32e __iomem *)
&mpc8xx_immr->im_cpm.cp_pbdir;
else
- iop = (struct cpm_ioport32 __iomem *)
+ iop = (struct cpm_ioport32e __iomem *)
&mpc8xx_immr->im_cpm.cp_pedir;
if (flags & CPM_PIN_OUTPUT)
return 0;
}
+
+/*
+ * GPIO LIB API implementation
+ */
+#ifdef CONFIG_8xx_GPIO
+
+struct cpm1_gpio16_chip {
+ struct of_mm_gpio_chip mm_gc;
+ spinlock_t lock;
+
+ /* shadowed data register to clear/set bits safely */
+ u16 cpdata;
+};
+
+static inline struct cpm1_gpio16_chip *
+to_cpm1_gpio16_chip(struct of_mm_gpio_chip *mm_gc)
+{
+ return container_of(mm_gc, struct cpm1_gpio16_chip, mm_gc);
+}
+
+static void cpm1_gpio16_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+ struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+ struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+
+ cpm1_gc->cpdata = in_be16(&iop->dat);
+}
+
+static int cpm1_gpio16_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+ u16 pin_mask;
+
+ pin_mask = 1 << (15 - gpio);
+
+ return !!(in_be16(&iop->dat) & pin_mask);
+}
+
+static void cpm1_gpio16_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm1_gpio16_chip *cpm1_gc = to_cpm1_gpio16_chip(mm_gc);
+ struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+ unsigned long flags;
+ u16 pin_mask = 1 << (15 - gpio);
+
+ spin_lock_irqsave(&cpm1_gc->lock, flags);
+
+ if (value)
+ cpm1_gc->cpdata |= pin_mask;
+ else
+ cpm1_gc->cpdata &= ~pin_mask;
+
+ out_be16(&iop->dat, cpm1_gc->cpdata);
+
+ spin_unlock_irqrestore(&cpm1_gc->lock, flags);
+}
+
+static int cpm1_gpio16_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+ u16 pin_mask;
+
+ pin_mask = 1 << (15 - gpio);
+
+ setbits16(&iop->dir, pin_mask);
+
+ cpm1_gpio16_set(gc, gpio, val);
+
+ return 0;
+}
+
+static int cpm1_gpio16_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport16 __iomem *iop = mm_gc->regs;
+ u16 pin_mask;
+
+ pin_mask = 1 << (15 - gpio);
+
+ clrbits16(&iop->dir, pin_mask);
+
+ return 0;
+}
+
+int cpm1_gpiochip_add16(struct device_node *np)
+{
+ struct cpm1_gpio16_chip *cpm1_gc;
+ struct of_mm_gpio_chip *mm_gc;
+ struct of_gpio_chip *of_gc;
+ struct gpio_chip *gc;
+
+ cpm1_gc = kzalloc(sizeof(*cpm1_gc), GFP_KERNEL);
+ if (!cpm1_gc)
+ return -ENOMEM;
+
+ spin_lock_init(&cpm1_gc->lock);
+
+ mm_gc = &cpm1_gc->mm_gc;
+ of_gc = &mm_gc->of_gc;
+ gc = &of_gc->gc;
+
+ mm_gc->save_regs = cpm1_gpio16_save_regs;
+ of_gc->gpio_cells = 2;
+ gc->ngpio = 16;
+ gc->direction_input = cpm1_gpio16_dir_in;
+ gc->direction_output = cpm1_gpio16_dir_out;
+ gc->get = cpm1_gpio16_get;
+ gc->set = cpm1_gpio16_set;
+
+ return of_mm_gpiochip_add(np, mm_gc);
+}
+
+struct cpm1_gpio32_chip {
+ struct of_mm_gpio_chip mm_gc;
+ spinlock_t lock;
+
+ /* shadowed data register to clear/set bits safely */
+ u32 cpdata;
+};
+
+static inline struct cpm1_gpio32_chip *
+to_cpm1_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
+{
+ return container_of(mm_gc, struct cpm1_gpio32_chip, mm_gc);
+}
+
+static void cpm1_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+ struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+ struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+
+ cpm1_gc->cpdata = in_be32(&iop->dat);
+}
+
+static int cpm1_gpio32_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ return !!(in_be32(&iop->dat) & pin_mask);
+}
+
+static void cpm1_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm1_gpio32_chip *cpm1_gc = to_cpm1_gpio32_chip(mm_gc);
+ struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+ unsigned long flags;
+ u32 pin_mask = 1 << (31 - gpio);
+
+ spin_lock_irqsave(&cpm1_gc->lock, flags);
+
+ if (value)
+ cpm1_gc->cpdata |= pin_mask;
+ else
+ cpm1_gc->cpdata &= ~pin_mask;
+
+ out_be32(&iop->dat, cpm1_gc->cpdata);
+
+ spin_unlock_irqrestore(&cpm1_gc->lock, flags);
+}
+
+static int cpm1_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ setbits32(&iop->dir, pin_mask);
+
+ cpm1_gpio32_set(gc, gpio, val);
+
+ return 0;
+}
+
+static int cpm1_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm_ioport32b __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ clrbits32(&iop->dir, pin_mask);
+
+ return 0;
+}
+
+int cpm1_gpiochip_add32(struct device_node *np)
+{
+ struct cpm1_gpio32_chip *cpm1_gc;
+ struct of_mm_gpio_chip *mm_gc;
+ struct of_gpio_chip *of_gc;
+ struct gpio_chip *gc;
+
+ cpm1_gc = kzalloc(sizeof(*cpm1_gc), GFP_KERNEL);
+ if (!cpm1_gc)
+ return -ENOMEM;
+
+ spin_lock_init(&cpm1_gc->lock);
+
+ mm_gc = &cpm1_gc->mm_gc;
+ of_gc = &mm_gc->of_gc;
+ gc = &of_gc->gc;
+
+ mm_gc->save_regs = cpm1_gpio32_save_regs;
+ of_gc->gpio_cells = 2;
+ gc->ngpio = 32;
+ gc->direction_input = cpm1_gpio32_dir_in;
+ gc->direction_output = cpm1_gpio32_dir_out;
+ gc->get = cpm1_gpio32_get;
+ gc->set = cpm1_gpio32_set;
+
+ return of_mm_gpiochip_add(np, mm_gc);
+}
+
+static int cpm_init_par_io(void)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-a")
+ cpm1_gpiochip_add16(np);
+
+ for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-b")
+ cpm1_gpiochip_add32(np);
+
+ for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-c")
+ cpm1_gpiochip_add16(np);
+
+ for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-d")
+ cpm1_gpiochip_add16(np);
+
+ /* Port E uses CPM2 layout */
+ for_each_compatible_node(np, NULL, "fsl,cpm1-pario-bank-e")
+ cpm2_gpiochip_add32(np);
+ return 0;
+}
+arch_initcall(cpm_init_par_io);
+
+#endif /* CONFIG_8xx_GPIO */
* Baud rate clocks are zero-based in the driver code (as that maps
* to port numbers). Documentation uses 1-based numbering.
*/
-#define BRG_INT_CLK (get_brgfreq())
-#define BRG_UART_CLK (BRG_INT_CLK/16)
-
-/* This function is used by UARTS, or anything else that uses a 16x
- * oversampled clock.
- */
-void
-cpm_setbrg(uint brg, uint rate)
+void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src)
{
u32 __iomem *bp;
+ u32 val;
/* This is good enough to get SMCs running.....
*/
brg -= 4;
}
bp += brg;
- out_be32(bp, (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN);
-
- cpm2_unmap(bp);
-}
-
-/* This function is used to set high speed synchronous baud rate
- * clocks.
- */
-void
-cpm2_fastbrg(uint brg, uint rate, int div16)
-{
- u32 __iomem *bp;
- u32 val;
-
- if (brg < 4) {
- bp = cpm2_map_size(im_brgc1, 16);
- } else {
- bp = cpm2_map_size(im_brgc5, 16);
- brg -= 4;
- }
- bp += brg;
- val = ((BRG_INT_CLK / rate) << 1) | CPM_BRG_EN;
+ val = (((clk / rate) - 1) << 1) | CPM_BRG_EN | src;
if (div16)
val |= CPM_BRG_DIV16;
out_be32(bp, val);
cpm2_unmap(bp);
}
+EXPORT_SYMBOL(__cpm2_setbrg);
int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode)
{
else
clrbits32(&iop[port].odr, pin);
}
+
+static int cpm_init_par_io(void)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, "fsl,cpm2-pario-bank")
+ cpm2_gpiochip_add32(np);
+ return 0;
+}
+arch_initcall(cpm_init_par_io);
+
#include <linux/init.h>
#include <linux/of_device.h>
+#include <linux/spinlock.h>
+#include <linux/of.h>
#include <asm/udbg.h>
#include <asm/io.h>
#include <mm/mmu_decl.h>
+#if defined(CONFIG_CPM2) || defined(CONFIG_8xx_GPIO)
+#include <linux/of_gpio.h>
+#endif
+
#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
static u32 __iomem *cpm_udbg_txdesc =
(u32 __iomem __force *)CONFIG_PPC_EARLY_DEBUG_CPM_ADDR;
return muram_pbase + ((u8 __iomem *)addr - muram_vbase);
}
EXPORT_SYMBOL(cpm_muram_dma);
+
+#if defined(CONFIG_CPM2) || defined(CONFIG_8xx_GPIO)
+
+struct cpm2_ioports {
+ u32 dir, par, sor, odr, dat;
+ u32 res[3];
+};
+
+struct cpm2_gpio32_chip {
+ struct of_mm_gpio_chip mm_gc;
+ spinlock_t lock;
+
+ /* shadowed data register to clear/set bits safely */
+ u32 cpdata;
+};
+
+static inline struct cpm2_gpio32_chip *
+to_cpm2_gpio32_chip(struct of_mm_gpio_chip *mm_gc)
+{
+ return container_of(mm_gc, struct cpm2_gpio32_chip, mm_gc);
+}
+
+static void cpm2_gpio32_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+ struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+ struct cpm2_ioports __iomem *iop = mm_gc->regs;
+
+ cpm2_gc->cpdata = in_be32(&iop->dat);
+}
+
+static int cpm2_gpio32_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm2_ioports __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ return !!(in_be32(&iop->dat) & pin_mask);
+}
+
+static void cpm2_gpio32_set(struct gpio_chip *gc, unsigned int gpio, int value)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm2_gpio32_chip *cpm2_gc = to_cpm2_gpio32_chip(mm_gc);
+ struct cpm2_ioports __iomem *iop = mm_gc->regs;
+ unsigned long flags;
+ u32 pin_mask = 1 << (31 - gpio);
+
+ spin_lock_irqsave(&cpm2_gc->lock, flags);
+
+ if (value)
+ cpm2_gc->cpdata |= pin_mask;
+ else
+ cpm2_gc->cpdata &= ~pin_mask;
+
+ out_be32(&iop->dat, cpm2_gc->cpdata);
+
+ spin_unlock_irqrestore(&cpm2_gc->lock, flags);
+}
+
+static int cpm2_gpio32_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm2_ioports __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ setbits32(&iop->dir, pin_mask);
+
+ cpm2_gpio32_set(gc, gpio, val);
+
+ return 0;
+}
+
+static int cpm2_gpio32_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct cpm2_ioports __iomem *iop = mm_gc->regs;
+ u32 pin_mask;
+
+ pin_mask = 1 << (31 - gpio);
+
+ clrbits32(&iop->dir, pin_mask);
+
+ return 0;
+}
+
+int cpm2_gpiochip_add32(struct device_node *np)
+{
+ struct cpm2_gpio32_chip *cpm2_gc;
+ struct of_mm_gpio_chip *mm_gc;
+ struct of_gpio_chip *of_gc;
+ struct gpio_chip *gc;
+
+ cpm2_gc = kzalloc(sizeof(*cpm2_gc), GFP_KERNEL);
+ if (!cpm2_gc)
+ return -ENOMEM;
+
+ spin_lock_init(&cpm2_gc->lock);
+
+ mm_gc = &cpm2_gc->mm_gc;
+ of_gc = &mm_gc->of_gc;
+ gc = &of_gc->gc;
+
+ mm_gc->save_regs = cpm2_gpio32_save_regs;
+ of_gc->gpio_cells = 2;
+ gc->ngpio = 32;
+ gc->direction_input = cpm2_gpio32_dir_in;
+ gc->direction_output = cpm2_gpio32_dir_out;
+ gc->get = cpm2_gpio32_get;
+ gc->set = cpm2_gpio32_set;
+
+ return of_mm_gpiochip_add(np, mm_gc);
+}
+#endif /* CONFIG_CPM2 || CONFIG_8xx_GPIO */
struct device_node *np;
struct platform_device *pd;
struct resource res[2];
+ unsigned int num_res = 1;
int ret;
memset(&res, 0, sizeof(res));
if (res[0].start != RTC_PORT(0))
return -EINVAL;
- /* Use a fixed interrupt value of 8 since on PPC if we are using this
- * its off an i8259 which we ensure has interrupt numbers 0..15. */
- res[1].start = 8;
- res[1].end = 8;
- res[1].flags = IORESOURCE_IRQ;
+ np = of_find_compatible_node(NULL, NULL, "chrp,iic");
+ if (!np)
+ np = of_find_compatible_node(NULL, NULL, "pnpPNP,000");
+ if (np) {
+ of_node_put(np);
+ /*
+ * Use a fixed interrupt value of 8 since on PPC if we are
+ * using this its off an i8259 which we ensure has interrupt
+ * numbers 0..15.
+ */
+ res[1].start = 8;
+ res[1].end = 8;
+ res[1].flags = IORESOURCE_IRQ;
+ num_res++;
+ }
pd = platform_device_register_simple("rtc_cmos", -1,
- &res[0], 2);
+ &res[0], num_res);
if (IS_ERR(pd))
return PTR_ERR(pd);
def_bool y
depends on SPARSEMEM
+config ARCH_ENABLE_MEMORY_HOTREMOVE
+ def_bool y
+
source "mm/Kconfig"
comment "I/O subsystem configuration"
void clock_comparator_work(void);
+static inline unsigned long long local_tick_disable(void)
+{
+ unsigned long long old;
+
+ old = S390_lowcore.clock_comparator;
+ S390_lowcore.clock_comparator = -1ULL;
+ return old;
+}
+
+static inline void local_tick_enable(unsigned long long comp)
+{
+ S390_lowcore.clock_comparator = comp;
+}
+
#endif /* __ASM_HARDIRQ_H */
};
enum diag308_rc {
- DIAG308_RC_OK = 1,
+ DIAG308_RC_OK = 0x0001,
+ DIAG308_RC_NOCONFIG = 0x0102,
};
extern int diag308(unsigned long subcode, void *addr);
} __attribute__ ((packed, aligned(4)));
#ifdef __KERNEL__
+#include <linux/string.h>
/* Helper function for sane state of pre-allocated subchannel_id. */
static inline void
#define MACHINE_FLAG_VM (1UL << 0)
#define MACHINE_FLAG_IEEE (1UL << 1)
-#define MACHINE_FLAG_P390 (1UL << 2)
#define MACHINE_FLAG_CSP (1UL << 3)
#define MACHINE_FLAG_MVPG (1UL << 4)
#define MACHINE_FLAG_DIAG44 (1UL << 5)
#define __NR_timerfd_create 319
#define __NR_timerfd_settime 320
#define __NR_timerfd_gettime 321
-#define NR_syscalls 322
+#define __NR_signalfd4 322
+#define __NR_eventfd2 323
+#define __NR_inotify_init1 324
+#define __NR_pipe2 325
+#define __NR_dup3 326
+#define __NR_epoll_create1 327
+#define NR_syscalls 328
/*
* There are some system calls that are not present on 64 bit, some
lgfr %r2,%r2 # int
llgtr %r3,%r3 # struct compat_itimerspec *
jg compat_sys_timerfd_gettime
+
+ .globl compat_sys_signalfd4_wrapper
+compat_sys_signalfd4_wrapper:
+ lgfr %r2,%r2 # int
+ llgtr %r3,%r3 # compat_sigset_t *
+ llgfr %r4,%r4 # compat_size_t
+ lgfr %r5,%r5 # int
+ jg compat_sys_signalfd4
+
+ .globl sys_eventfd2_wrapper
+sys_eventfd2_wrapper:
+ llgfr %r2,%r2 # unsigned int
+ lgfr %r3,%r3 # int
+ jg sys_eventfd2
+
+ .globl sys_inotify_init1_wrapper
+sys_inotify_init1_wrapper:
+ lgfr %r2,%r2 # int
+ jg sys_inotify_init1
+
+ .globl sys_pipe2_wrapper
+sys_pipe2_wrapper:
+ llgtr %r2,%r2 # u32 *
+ lgfr %r3,%r3 # int
+ jg sys_pipe2 # branch to system call
+
+ .globl sys_dup3_wrapper
+sys_dup3_wrapper:
+ llgfr %r2,%r2 # unsigned int
+ llgfr %r3,%r3 # unsigned int
+ lgfr %r4,%r4 # int
+ jg sys_dup3 # branch to system call
+
+ .globl sys_epoll_create1_wrapper
+sys_epoll_create1_wrapper:
+ lgfr %r2,%r2 # int
+ jg sys_epoll_create1 # branch to system call
void __init ipl_update_parameters(void)
{
- if (diag308(DIAG308_STORE, &ipl_block) == DIAG308_RC_OK)
+ int rc;
+
+ rc = diag308(DIAG308_STORE, &ipl_block);
+ if ((rc == DIAG308_RC_OK) || (rc == DIAG308_RC_NOCONFIG))
diag308_set_works = 1;
}
#include <asm/sclp.h>
#include <asm/setup.h>
-static int memory_fast_detect(struct mem_chunk *chunk)
-{
- unsigned long val0 = 0;
- unsigned long val1 = 0xc;
- int rc = -EOPNOTSUPP;
-
- if (ipl_flags & IPL_NSS_VALID)
- return -EOPNOTSUPP;
- asm volatile(
- " diag %1,%2,0x260\n"
- "0: lhi %0,0\n"
- "1:\n"
- EX_TABLE(0b,1b)
- : "+d" (rc), "+d" (val0), "+d" (val1) : : "cc");
-
- if (rc || val0 != val1)
- return -EOPNOTSUPP;
- chunk->size = val0 + 1;
- return 0;
-}
-
static inline int tprot(unsigned long addr)
{
int rc = -EFAULT;
unsigned long flags, cr0;
memset(chunk, 0, MEMORY_CHUNKS * sizeof(struct mem_chunk));
- if (memory_fast_detect(&chunk[0]) == 0)
- return;
/* Disable IRQs, DAT and low address protection so tprot does the
* right thing and we don't get scheduled away with low address
* protection disabled.
SYSCALL(sys_timerfd_create,sys_timerfd_create,sys_timerfd_create_wrapper)
SYSCALL(sys_timerfd_settime,sys_timerfd_settime,compat_sys_timerfd_settime_wrapper) /* 320 */
SYSCALL(sys_timerfd_gettime,sys_timerfd_gettime,compat_sys_timerfd_gettime_wrapper)
+SYSCALL(sys_signalfd4,sys_signalfd4,compat_sys_signalfd4_wrapper)
+SYSCALL(sys_eventfd2,sys_eventfd2,sys_eventfd2_wrapper)
+SYSCALL(sys_inotify_init1,sys_inotify_init1,sys_inotify_init1_wrapper)
+SYSCALL(sys_pipe2,sys_pipe2,sys_pipe2_wrapper) /* 325 */
+SYSCALL(sys_dup3,sys_dup3,sys_dup3_wrapper)
+SYSCALL(sys_epoll_create1,sys_epoll_create1,sys_epoll_create1_wrapper)
/*
* Reset STP attachment.
*/
-static void stp_reset(void)
+static void __init stp_reset(void)
{
int rc;
vcpu->stat.instruction_stfl++;
facility_list &= ~(1UL<<24); /* no stfle */
+ facility_list &= ~(1UL<<23); /* no large pages */
rc = copy_to_guest(vcpu, offsetof(struct _lowcore, stfl_fac_list),
&facility_list, sizeof(facility_list));
local_bh_disable();
local_irq_save(flags);
if (raw_irqs_disabled_flags(flags)) {
- old_cc = S390_lowcore.clock_comparator;
+ old_cc = local_tick_disable();
S390_lowcore.clock_comparator = -1ULL;
__ctl_store(cr0, 0, 0);
dummy = (cr0 & 0xffff00e0) | 0x00000800;
if (raw_irqs_disabled_flags(flags)) {
__ctl_load(cr0, 0, 0);
- S390_lowcore.clock_comparator = old_cc;
+ local_tick_enable(old_cc);
}
if (!irq_context)
_local_bh_enable();
int rc;
pgdat = NODE_DATA(nid);
- zone = pgdat->node_zones + ZONE_NORMAL;
+ zone = pgdat->node_zones + ZONE_MOVABLE;
rc = vmem_add_mapping(start, size);
if (rc)
return rc;
return rc;
}
#endif /* CONFIG_MEMORY_HOTPLUG */
+
+#ifdef CONFIG_MEMORY_HOTREMOVE
+int remove_memory(u64 start, u64 size)
+{
+ unsigned long start_pfn, end_pfn;
+
+ start_pfn = PFN_DOWN(start);
+ end_pfn = start_pfn + PFN_DOWN(size);
+ return offline_pages(start_pfn, end_pfn, 120 * HZ);
+}
+#endif /* CONFIG_MEMORY_HOTREMOVE */
config SUPERH64
def_bool y if CPU_SH5
+config ARCH_DEFCONFIG
+ string
+ default "arch/sh/configs/shx3_defconfig" if SUPERH32
+ default "arch/sh/configs/cayman_defconfig" if SUPERH64
+
config RWSEM_GENERIC_SPINLOCK
def_bool y
config GENERIC_HARDIRQS
def_bool y
+config GENERIC_HARDIRQS_NO__DO_IRQ
+ def_bool y
+
config GENERIC_IRQ_PROBE
def_bool y
config GENERIC_CLOCKEVENTS
def_bool n
+config GENERIC_LOCKBREAK
+ def_bool y
+ depends on SMP && PREEMPT
+
config SYS_SUPPORTS_PM
bool
config ARCH_NO_VIRT_TO_BUS
def_bool y
-config ARCH_SUPPORTS_AOUT
- def_bool y
-
config IO_TRAPPED
bool
endchoice
source "arch/sh/mm/Kconfig"
+
source "arch/sh/Kconfig.cpu"
-menu "Board support"
-
-config SOLUTION_ENGINE
- bool
-
-config SH_SOLUTION_ENGINE
- bool "SolutionEngine"
- select SOLUTION_ENGINE
- select CPU_HAS_IPR_IRQ
- depends on CPU_SUBTYPE_SH7705 || CPU_SUBTYPE_SH7709 || CPU_SUBTYPE_SH7710 || \
- CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \
- CPU_SUBTYPE_SH7750R
- help
- Select SolutionEngine if configuring for a Hitachi SH7705, SH7709,
- SH7710, SH7712, SH7750, SH7750S or SH7750R evaluation board.
-
-config SH_7206_SOLUTION_ENGINE
- bool "SolutionEngine7206"
- select SOLUTION_ENGINE
- depends on CPU_SUBTYPE_SH7206
- help
- Select 7206 SolutionEngine if configuring for a Hitachi SH7206
- evaluation board.
-
-config SH_7619_SOLUTION_ENGINE
- bool "SolutionEngine7619"
- select SOLUTION_ENGINE
- depends on CPU_SUBTYPE_SH7619
- help
- Select 7619 SolutionEngine if configuring for a Hitachi SH7619
- evaluation board.
-
-config SH_7721_SOLUTION_ENGINE
- bool "SolutionEngine7721"
- select SOLUTION_ENGINE
- depends on CPU_SUBTYPE_SH7721
- help
- Select 7721 SolutionEngine if configuring for a Hitachi SH7721
- evaluation board.
-
-config SH_7722_SOLUTION_ENGINE
- bool "SolutionEngine7722"
- select SOLUTION_ENGINE
- depends on CPU_SUBTYPE_SH7722
- help
- Select 7722 SolutionEngine if configuring for a Hitachi SH772
- evaluation board.
-
-config SH_7751_SOLUTION_ENGINE
- bool "SolutionEngine7751"
- select SOLUTION_ENGINE
- select CPU_HAS_IPR_IRQ
- depends on CPU_SUBTYPE_SH7751
- help
- Select 7751 SolutionEngine if configuring for a Hitachi SH7751
- evaluation board.
-
-config SH_7780_SOLUTION_ENGINE
- bool "SolutionEngine7780"
- select SOLUTION_ENGINE
- select SYS_SUPPORTS_PCI
- depends on CPU_SUBTYPE_SH7780
- help
- Select 7780 SolutionEngine if configuring for a Renesas SH7780
- evaluation board.
-
-config SH_7343_SOLUTION_ENGINE
- bool "SolutionEngine7343"
- select SOLUTION_ENGINE
- depends on CPU_SUBTYPE_SH7343
- help
- Select 7343 SolutionEngine if configuring for a Hitachi
- SH7343 (SH-Mobile 3AS) evaluation board.
-
-config SH_7751_SYSTEMH
- bool "SystemH7751R"
- depends on CPU_SUBTYPE_SH7751R
- help
- Select SystemH if you are configuring for a Renesas SystemH
- 7751R evaluation board.
-
-config SH_HP6XX
- bool "HP6XX"
- select SYS_SUPPORTS_APM_EMULATION
- select HD6446X_SERIES
- depends on CPU_SUBTYPE_SH7709
- help
- Select HP6XX if configuring for a HP jornada HP6xx.
- More information (hardware only) at
- <http://www.hp.com/jornada/>.
-
-config SH_DREAMCAST
- bool "Dreamcast"
- select SYS_SUPPORTS_PCI
- depends on CPU_SUBTYPE_SH7091
- help
- Select Dreamcast if configuring for a SEGA Dreamcast.
- More information at <http://www.linux-sh.org>
-
-config SH_SH03
- bool "Interface CTP/PCI-SH03"
- depends on CPU_SUBTYPE_SH7751
- select CPU_HAS_IPR_IRQ
- select SYS_SUPPORTS_PCI
- help
- CTP/PCI-SH03 is a CPU module computer that is produced
- by Interface Corporation.
- More information at <http://www.interface.co.jp>
-
-config SH_SECUREEDGE5410
- bool "SecureEdge5410"
- depends on CPU_SUBTYPE_SH7751R
- select CPU_HAS_IPR_IRQ
- select SYS_SUPPORTS_PCI
- help
- Select SecureEdge5410 if configuring for a SnapGear SH board.
- This includes both the OEM SecureEdge products as well as the
- SME product line.
-
-config SH_RTS7751R2D
- bool "RTS7751R2D"
- depends on CPU_SUBTYPE_SH7751R
- select SYS_SUPPORTS_PCI
- select IO_TRAPPED
- help
- Select RTS7751R2D if configuring for a Renesas Technology
- Sales SH-Graphics board.
-
-config SH_RSK7203
- bool "RSK7203"
- depends on CPU_SUBTYPE_SH7203
-
-config SH_SDK7780
- bool "SDK7780R3"
- depends on CPU_SUBTYPE_SH7780
- select SYS_SUPPORTS_PCI
- help
- Select SDK7780 if configuring for a Renesas SH7780 SDK7780R3
- evaluation board.
-
-config SH_HIGHLANDER
- bool "Highlander"
- depends on CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785
- select SYS_SUPPORTS_PCI
- select IO_TRAPPED
-
-config SH_SH7785LCR
- bool "SH7785LCR"
- depends on CPU_SUBTYPE_SH7785
- select SYS_SUPPORTS_PCI
- select IO_TRAPPED
-
-config SH_SH7785LCR_29BIT_PHYSMAPS
- bool "SH7785LCR 29bit physmaps"
- depends on SH_SH7785LCR
- default y
- help
- This board has 2 physical memory maps. It can be changed with
- DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
- you can access all on-board device in 29bit address mode.
-
-config SH_MIGOR
- bool "Migo-R"
- depends on CPU_SUBTYPE_SH7722
- help
- Select Migo-R if configuring for the SH7722 Migo-R platform
- by Renesas System Solutions Asia Pte. Ltd.
-
-config SH_AP325RXA
- bool "AP-325RXA"
- depends on CPU_SUBTYPE_SH7723
- help
- Renesas "AP-325RXA" support.
- Compatible with ALGO SYSTEM CO.,LTD. "AP-320A"
-
-config SH_SH7763RDP
- bool "SH7763RDP"
- depends on CPU_SUBTYPE_SH7763
- help
- Select SH7763RDP if configuring for a Renesas SH7763
- evaluation board.
-
-config SH_EDOSK7705
- bool "EDOSK7705"
- depends on CPU_SUBTYPE_SH7705
-
-config SH_SH4202_MICRODEV
- bool "SH4-202 MicroDev"
- depends on CPU_SUBTYPE_SH4_202
- help
- Select SH4-202 MicroDev if configuring for a SuperH MicroDev board
- with an SH4-202 CPU.
-
-config SH_LANDISK
- bool "LANDISK"
- depends on CPU_SUBTYPE_SH7751R
- select SYS_SUPPORTS_PCI
- help
- I-O DATA DEVICE, INC. "LANDISK Series" support.
-
-config SH_TITAN
- bool "TITAN"
- depends on CPU_SUBTYPE_SH7751R
- select CPU_HAS_IPR_IRQ
- select SYS_SUPPORTS_PCI
- help
- Select Titan if you are configuring for a Nimble Microsystems
- NetEngine NP51R.
-
-config SH_SHMIN
- bool "SHMIN"
- depends on CPU_SUBTYPE_SH7706
- select CPU_HAS_IPR_IRQ
- help
- Select SHMIN if configuring for the SHMIN board.
-
-config SH_LBOX_RE2
- bool "L-BOX RE2"
- depends on CPU_SUBTYPE_SH7751R
- select SYS_SUPPORTS_PCI
- help
- Select L-BOX RE2 if configuring for the NTT COMWARE L-BOX RE2.
-
-config SH_X3PROTO
- bool "SH-X3 Prototype board"
- depends on CPU_SUBTYPE_SHX3
-
-config SH_MAGIC_PANEL_R2
- bool "Magic Panel R2"
- depends on CPU_SUBTYPE_SH7720
- help
- Select Magic Panel R2 if configuring for Magic Panel R2.
-
-config SH_CAYMAN
- bool "Hitachi Cayman"
- depends on CPU_SUBTYPE_SH5_101 || CPU_SUBTYPE_SH5_103
- select SYS_SUPPORTS_PCI
-
-endmenu
-
-source "arch/sh/boards/renesas/rts7751r2d/Kconfig"
-source "arch/sh/boards/renesas/r7780rp/Kconfig"
-source "arch/sh/boards/renesas/sdk7780/Kconfig"
-source "arch/sh/boards/renesas/migor/Kconfig"
-source "arch/sh/boards/magicpanelr2/Kconfig"
+source "arch/sh/boards/Kconfig"
menu "Timer and clock configuration"
For more details see Documentation/kdump/kdump.txt
+config SECCOMP
+ bool "Enable seccomp to safely compute untrusted bytecode"
+ depends on PROC_FS
+ default y
+ help
+ This kernel feature is useful for number crunching applications
+ that may need to compute untrusted bytecode during their
+ execution. By using pipes or other transports made available to
+ the process as file descriptors supporting the read/write
+ syscalls, it's possible to isolate those applications in
+ their own address space using seccomp. Once seccomp is
+ enabled via prctl, it cannot be disabled and the task is only
+ allowed to execute a few safe syscalls defined by each seccomp
+ mode.
+
+ If unsure, say N.
+
config SMP
bool "Symmetric multi-processing support"
depends on SYS_SUPPORTS_SMP
config SH64_PROC_ASIDS
bool "Debug: report ASIDs through /proc/asids"
- depends on PROC_FS
+ depends on PROC_FS && MMU
config SH64_SR_WATCH
bool "Debug: set SR.WATCH to enable hardware watchpoints and trace"
defaultimage-$(CONFIG_SUPERH32) := zImage
# Set some sensible Kbuild defaults
-KBUILD_DEFCONFIG := r7780mp_defconfig
+KBUILD_DEFCONFIG := shx3_defconfig
KBUILD_IMAGE := $(defaultimage-y)
#
LDFLAGS += -EB
endif
-KBUILD_CFLAGS += -pipe $(cflags-y)
-KBUILD_AFLAGS += $(cflags-y)
-
head-y := arch/sh/kernel/init_task.o
head-$(CONFIG_SUPERH32) += arch/sh/kernel/head_32.o
head-$(CONFIG_SUPERH64) += arch/sh/kernel/head_64.o
-LIBGCC := $(shell $(CC) $(KBUILD_CFLAGS) -print-libgcc-file-name)
-
-core-y += arch/sh/kernel/ arch/sh/mm/
+core-y += arch/sh/kernel/ arch/sh/mm/ arch/sh/boards/
core-$(CONFIG_SH_FPU_EMU) += arch/sh/math-emu/
-# Boards
-machdir-$(CONFIG_SH_SOLUTION_ENGINE) += se/770x
-machdir-$(CONFIG_SH_7722_SOLUTION_ENGINE) += se/7722
-machdir-$(CONFIG_SH_7751_SOLUTION_ENGINE) += se/7751
-machdir-$(CONFIG_SH_7780_SOLUTION_ENGINE) += se/7780
-machdir-$(CONFIG_SH_7343_SOLUTION_ENGINE) += se/7343
-machdir-$(CONFIG_SH_7721_SOLUTION_ENGINE) += se/7721
-machdir-$(CONFIG_SH_HP6XX) += hp6xx
-machdir-$(CONFIG_SH_DREAMCAST) += dreamcast
-machdir-$(CONFIG_SH_SH03) += sh03
-machdir-$(CONFIG_SH_SECUREEDGE5410) += snapgear
-machdir-$(CONFIG_SH_RTS7751R2D) += renesas/rts7751r2d
-machdir-$(CONFIG_SH_7751_SYSTEMH) += renesas/systemh
-machdir-$(CONFIG_SH_EDOSK7705) += renesas/edosk7705
-machdir-$(CONFIG_SH_HIGHLANDER) += renesas/r7780rp
-machdir-$(CONFIG_SH_MIGOR) += renesas/migor
-machdir-$(CONFIG_SH_SDK7780) += renesas/sdk7780
-machdir-$(CONFIG_SH_X3PROTO) += renesas/x3proto
-machdir-$(CONFIG_SH_RSK7203) += renesas/rsk7203
-machdir-$(CONFIG_SH_AP325RXA) += renesas/ap325rxa
-machdir-$(CONFIG_SH_SH7763RDP) += renesas/sh7763rdp
-machdir-$(CONFIG_SH_SH7785LCR) += renesas/sh7785lcr
-machdir-$(CONFIG_SH_SH4202_MICRODEV) += superh/microdev
-machdir-$(CONFIG_SH_LANDISK) += landisk
-machdir-$(CONFIG_SH_TITAN) += titan
-machdir-$(CONFIG_SH_SHMIN) += shmin
-machdir-$(CONFIG_SH_7206_SOLUTION_ENGINE) += se/7206
-machdir-$(CONFIG_SH_7619_SOLUTION_ENGINE) += se/7619
-machdir-$(CONFIG_SH_LBOX_RE2) += lboxre2
-machdir-$(CONFIG_SH_MAGIC_PANEL_R2) += magicpanelr2
-machdir-$(CONFIG_SH_CAYMAN) += cayman
-
-incdir-y := $(notdir $(machdir-y))
+# Mach groups
+machdir-$(CONFIG_SOLUTION_ENGINE) += mach-se
+machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx
+machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast
+machdir-$(CONFIG_SH_SH03) += mach-sh03
+machdir-$(CONFIG_SH_SECUREEDGE5410) += mach-snapgear
+machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d
+machdir-$(CONFIG_SH_7751_SYSTEMH) += mach-systemh
+machdir-$(CONFIG_SH_EDOSK7705) += mach-edosk7705
+machdir-$(CONFIG_SH_HIGHLANDER) += mach-highlander
+machdir-$(CONFIG_SH_MIGOR) += mach-migor
+machdir-$(CONFIG_SH_SDK7780) += mach-sdk7780
+machdir-$(CONFIG_SH_X3PROTO) += mach-x3proto
+machdir-$(CONFIG_SH_SH7763RDP) += mach-sh7763rdp
+machdir-$(CONFIG_SH_SH4202_MICRODEV) += mach-microdev
+machdir-$(CONFIG_SH_LANDISK) += mach-landisk
+machdir-$(CONFIG_SH_TITAN) += mach-titan
+machdir-$(CONFIG_SH_LBOX_RE2) += mach-lboxre2
+machdir-$(CONFIG_SH_CAYMAN) += mach-cayman
ifneq ($(machdir-y),)
core-y += $(addprefix arch/sh/boards/, \
# Companion chips
core-$(CONFIG_HD6446X_SERIES) += arch/sh/cchips/hd6446x/
-cpuincdir-$(CONFIG_CPU_SH2) := cpu-sh2
-cpuincdir-$(CONFIG_CPU_SH2A) := cpu-sh2a
-cpuincdir-$(CONFIG_CPU_SH3) := cpu-sh3
-cpuincdir-$(CONFIG_CPU_SH4) := cpu-sh4
-cpuincdir-$(CONFIG_CPU_SH5) := cpu-sh5
-
-libs-$(CONFIG_SUPERH32) := arch/sh/lib/ $(libs-y)
-libs-$(CONFIG_SUPERH64) := arch/sh/lib64/ $(libs-y)
-libs-y += $(LIBGCC)
+#
+# CPU header paths
+#
+# These are ordered by optimization level. A CPU family that is a subset
+# of another (ie, SH-2A / SH-2), is picked up first, with increasing
+# levels of genericness if nothing more suitable is situated in the
+# hierarchy.
+#
+# As an example, in order of preference, SH-2A > SH-2 > common definitions.
+#
+cpuincdir-$(CONFIG_CPU_SH2A) += cpu-sh2a
+cpuincdir-$(CONFIG_CPU_SH2) += cpu-sh2
+cpuincdir-$(CONFIG_CPU_SH3) += cpu-sh3
+cpuincdir-$(CONFIG_CPU_SH4) += cpu-sh4
+cpuincdir-$(CONFIG_CPU_SH5) += cpu-sh5
+cpuincdir-y += cpu-common # Must be last
drivers-y += arch/sh/drivers/
drivers-$(CONFIG_OPROFILE) += arch/sh/oprofile/
boot := arch/sh/boot
-ifneq ($(KBUILD_SRC),)
-incdir-prefix := $(srctree)/include/asm-sh/
-else
-incdir-prefix :=
-endif
+cflags-y += $(foreach d, $(cpuincdir-y), -Iarch/sh/include/$(d)) \
+ $(foreach d, $(machdir-y), -Iarch/sh/include/$(d))
-# Update machine arch and proc symlinks if something which affects
-# them changed. We use .arch and .mach to indicate when they were
-# updated last, otherwise make uses the target directory mtime.
+KBUILD_CFLAGS += -pipe $(cflags-y)
+KBUILD_CPPFLAGS += $(cflags-y)
+KBUILD_AFLAGS += $(cflags-y)
-include/asm-sh/.cpu: $(wildcard include/config/cpu/*.h) \
- include/config/auto.conf FORCE
- @echo ' SYMLINK include/asm-sh/cpu -> include/asm-sh/$(cpuincdir-y)'
- $(Q)if [ ! -d include/asm-sh ]; then mkdir -p include/asm-sh; fi
- $(Q)ln -fsn $(incdir-prefix)$(cpuincdir-y) include/asm-sh/cpu
- @touch $@
+LIBGCC := $(shell $(CC) $(KBUILD_CFLAGS) -print-libgcc-file-name)
-# Most boards have their own mach directories. For the ones that
-# don't, just reference the parent directory so the semantics are
-# kept roughly the same.
-#
-# When multiple boards are compiled in at the same time, preference
-# for the mach link is given to whichever has a directory for its
-# headers. However, this is only a workaround until platforms that
-# can live in the same kernel image back away from relying on the
-# mach link.
-
-include/asm-sh/.mach: $(wildcard include/config/sh/*.h) \
- include/config/auto.conf FORCE
- $(Q)if [ ! -d include/asm-sh ]; then mkdir -p include/asm-sh; fi
- $(Q)rm -f include/asm-sh/mach
- $(Q)for i in $(incdir-y); do \
- if [ -d $(srctree)/include/asm-sh/$$i ]; then \
- echo -n ' SYMLINK include/asm-sh/mach -> '; \
- echo -e "include/asm-sh/$$i"; \
- ln -fsn $(incdir-prefix)$$i \
- include/asm-sh/mach; \
- else \
- if [ ! -d include/asm-sh/mach ]; then \
- echo -n ' SYMLINK include/asm-sh/mach -> '; \
- echo -e 'include/asm-sh'; \
- ln -fsn $(incdir-prefix)../asm-sh include/asm-sh/mach; \
- fi; \
- fi; \
- done
- @touch $@
+libs-$(CONFIG_SUPERH32) := arch/sh/lib/ $(libs-y)
+libs-$(CONFIG_SUPERH64) := arch/sh/lib64/ $(libs-y)
+libs-y += $(LIBGCC)
PHONY += maketools FORCE
compressed: zImage
-archprepare: include/asm-sh/.cpu include/asm-sh/.mach maketools \
- arch/sh/lib64/syscalltab.h
+archprepare: maketools arch/sh/lib64/syscalltab.h
archclean:
$(Q)$(MAKE) $(clean)=$(boot)
$(call filechk,gen-syscalltab)
CLEAN_FILES += arch/sh/lib64/syscalltab.h \
- include/asm-sh/machtypes.h \
- include/asm-sh/cpu include/asm-sh/.cpu \
- include/asm-sh/mach include/asm-sh/.mach
+ include/asm-sh/machtypes.h
--- /dev/null
+menu "Board support"
+
+config SOLUTION_ENGINE
+ bool
+
+config SH_SOLUTION_ENGINE
+ bool "SolutionEngine"
+ select SOLUTION_ENGINE
+ select CPU_HAS_IPR_IRQ
+ depends on CPU_SUBTYPE_SH7705 || CPU_SUBTYPE_SH7709 || CPU_SUBTYPE_SH7710 || \
+ CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \
+ CPU_SUBTYPE_SH7750R
+ help
+ Select SolutionEngine if configuring for a Hitachi SH7705, SH7709,
+ SH7710, SH7712, SH7750, SH7750S or SH7750R evaluation board.
+
+config SH_7206_SOLUTION_ENGINE
+ bool "SolutionEngine7206"
+ select SOLUTION_ENGINE
+ depends on CPU_SUBTYPE_SH7206
+ help
+ Select 7206 SolutionEngine if configuring for a Hitachi SH7206
+ evaluation board.
+
+config SH_7619_SOLUTION_ENGINE
+ bool "SolutionEngine7619"
+ select SOLUTION_ENGINE
+ depends on CPU_SUBTYPE_SH7619
+ help
+ Select 7619 SolutionEngine if configuring for a Hitachi SH7619
+ evaluation board.
+
+config SH_7721_SOLUTION_ENGINE
+ bool "SolutionEngine7721"
+ select SOLUTION_ENGINE
+ depends on CPU_SUBTYPE_SH7721
+ help
+ Select 7721 SolutionEngine if configuring for a Hitachi SH7721
+ evaluation board.
+
+config SH_7722_SOLUTION_ENGINE
+ bool "SolutionEngine7722"
+ select SOLUTION_ENGINE
+ depends on CPU_SUBTYPE_SH7722
+ help
+ Select 7722 SolutionEngine if configuring for a Hitachi SH772
+ evaluation board.
+
+config SH_7751_SOLUTION_ENGINE
+ bool "SolutionEngine7751"
+ select SOLUTION_ENGINE
+ select CPU_HAS_IPR_IRQ
+ depends on CPU_SUBTYPE_SH7751
+ help
+ Select 7751 SolutionEngine if configuring for a Hitachi SH7751
+ evaluation board.
+
+config SH_7780_SOLUTION_ENGINE
+ bool "SolutionEngine7780"
+ select SOLUTION_ENGINE
+ select SYS_SUPPORTS_PCI
+ depends on CPU_SUBTYPE_SH7780
+ help
+ Select 7780 SolutionEngine if configuring for a Renesas SH7780
+ evaluation board.
+
+config SH_7343_SOLUTION_ENGINE
+ bool "SolutionEngine7343"
+ select SOLUTION_ENGINE
+ depends on CPU_SUBTYPE_SH7343
+ help
+ Select 7343 SolutionEngine if configuring for a Hitachi
+ SH7343 (SH-Mobile 3AS) evaluation board.
+
+config SH_7751_SYSTEMH
+ bool "SystemH7751R"
+ depends on CPU_SUBTYPE_SH7751R
+ help
+ Select SystemH if you are configuring for a Renesas SystemH
+ 7751R evaluation board.
+
+config SH_HP6XX
+ bool "HP6XX"
+ select SYS_SUPPORTS_APM_EMULATION
+ select HD6446X_SERIES
+ depends on CPU_SUBTYPE_SH7709
+ help
+ Select HP6XX if configuring for a HP jornada HP6xx.
+ More information (hardware only) at
+ <http://www.hp.com/jornada/>.
+
+config SH_DREAMCAST
+ bool "Dreamcast"
+ select SYS_SUPPORTS_PCI
+ depends on CPU_SUBTYPE_SH7091
+ help
+ Select Dreamcast if configuring for a SEGA Dreamcast.
+ More information at <http://www.linux-sh.org>
+
+config SH_SH03
+ bool "Interface CTP/PCI-SH03"
+ depends on CPU_SUBTYPE_SH7751
+ select CPU_HAS_IPR_IRQ
+ select SYS_SUPPORTS_PCI
+ help
+ CTP/PCI-SH03 is a CPU module computer that is produced
+ by Interface Corporation.
+ More information at <http://www.interface.co.jp>
+
+config SH_SECUREEDGE5410
+ bool "SecureEdge5410"
+ depends on CPU_SUBTYPE_SH7751R
+ select CPU_HAS_IPR_IRQ
+ select SYS_SUPPORTS_PCI
+ help
+ Select SecureEdge5410 if configuring for a SnapGear SH board.
+ This includes both the OEM SecureEdge products as well as the
+ SME product line.
+
+config SH_RTS7751R2D
+ bool "RTS7751R2D"
+ depends on CPU_SUBTYPE_SH7751R
+ select SYS_SUPPORTS_PCI
+ select IO_TRAPPED
+ help
+ Select RTS7751R2D if configuring for a Renesas Technology
+ Sales SH-Graphics board.
+
+config SH_RSK7203
+ bool "RSK7203"
+ depends on CPU_SUBTYPE_SH7203
+
+config SH_SDK7780
+ bool "SDK7780R3"
+ depends on CPU_SUBTYPE_SH7780
+ select SYS_SUPPORTS_PCI
+ help
+ Select SDK7780 if configuring for a Renesas SH7780 SDK7780R3
+ evaluation board.
+
+config SH_HIGHLANDER
+ bool "Highlander"
+ depends on CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785
+ select SYS_SUPPORTS_PCI
+ select IO_TRAPPED
+
+config SH_SH7785LCR
+ bool "SH7785LCR"
+ depends on CPU_SUBTYPE_SH7785
+ select SYS_SUPPORTS_PCI
+ select IO_TRAPPED
+
+config SH_SH7785LCR_29BIT_PHYSMAPS
+ bool "SH7785LCR 29bit physmaps"
+ depends on SH_SH7785LCR
+ default y
+ help
+ This board has 2 physical memory maps. It can be changed with
+ DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
+ you can access all on-board device in 29bit address mode.
+
+config SH_MIGOR
+ bool "Migo-R"
+ depends on CPU_SUBTYPE_SH7722
+ help
+ Select Migo-R if configuring for the SH7722 Migo-R platform
+ by Renesas System Solutions Asia Pte. Ltd.
+
+config SH_AP325RXA
+ bool "AP-325RXA"
+ depends on CPU_SUBTYPE_SH7723
+ help
+ Renesas "AP-325RXA" support.
+ Compatible with ALGO SYSTEM CO.,LTD. "AP-320A"
+
+config SH_SH7763RDP
+ bool "SH7763RDP"
+ depends on CPU_SUBTYPE_SH7763
+ help
+ Select SH7763RDP if configuring for a Renesas SH7763
+ evaluation board.
+
+config SH_EDOSK7705
+ bool "EDOSK7705"
+ depends on CPU_SUBTYPE_SH7705
+
+config SH_SH4202_MICRODEV
+ bool "SH4-202 MicroDev"
+ depends on CPU_SUBTYPE_SH4_202
+ help
+ Select SH4-202 MicroDev if configuring for a SuperH MicroDev board
+ with an SH4-202 CPU.
+
+config SH_LANDISK
+ bool "LANDISK"
+ depends on CPU_SUBTYPE_SH7751R
+ select SYS_SUPPORTS_PCI
+ help
+ I-O DATA DEVICE, INC. "LANDISK Series" support.
+
+config SH_TITAN
+ bool "TITAN"
+ depends on CPU_SUBTYPE_SH7751R
+ select CPU_HAS_IPR_IRQ
+ select SYS_SUPPORTS_PCI
+ help
+ Select Titan if you are configuring for a Nimble Microsystems
+ NetEngine NP51R.
+
+config SH_SHMIN
+ bool "SHMIN"
+ depends on CPU_SUBTYPE_SH7706
+ select CPU_HAS_IPR_IRQ
+ help
+ Select SHMIN if configuring for the SHMIN board.
+
+config SH_LBOX_RE2
+ bool "L-BOX RE2"
+ depends on CPU_SUBTYPE_SH7751R
+ select SYS_SUPPORTS_PCI
+ help
+ Select L-BOX RE2 if configuring for the NTT COMWARE L-BOX RE2.
+
+config SH_X3PROTO
+ bool "SH-X3 Prototype board"
+ depends on CPU_SUBTYPE_SHX3
+
+config SH_MAGIC_PANEL_R2
+ bool "Magic Panel R2"
+ depends on CPU_SUBTYPE_SH7720
+ help
+ Select Magic Panel R2 if configuring for Magic Panel R2.
+
+config SH_CAYMAN
+ bool "Hitachi Cayman"
+ depends on CPU_SUBTYPE_SH5_101 || CPU_SUBTYPE_SH5_103
+ select SYS_SUPPORTS_PCI
+
+endmenu
+
+source "arch/sh/boards/mach-r2d/Kconfig"
+source "arch/sh/boards/mach-highlander/Kconfig"
+source "arch/sh/boards/mach-sdk7780/Kconfig"
+source "arch/sh/boards/mach-migor/Kconfig"
+
+if SH_MAGIC_PANEL_R2
+
+menu "Magic Panel R2 options"
+
+config SH_MAGIC_PANEL_R2_VERSION
+ int SH_MAGIC_PANEL_R2_VERSION
+ default "3"
+ help
+ Set the version of the Magic Panel R2
+
+endmenu
+
+endif
--- /dev/null
+#
+# Specific board support, not covered by a mach group.
+#
+obj-$(CONFIG_SH_AP325RXA) += board-ap325rxa.o
+obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o
+obj-$(CONFIG_SH_RSK7203) += board-rsk7203.o
+obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o
+obj-$(CONFIG_SH_SHMIN) += board-shmin.o
#include <linux/mtd/physmap.h>
#include <linux/delay.h>
#include <linux/i2c.h>
-#include <linux/delay.h>
#include <linux/smc911x.h>
#include <media/soc_camera_platform.h>
#include <media/sh_mobile_ceu.h>
},
};
+#ifdef CONFIG_I2C
static unsigned char camera_ncm03j_magic[] =
{
0x87, 0x00, 0x88, 0x08, 0x89, 0x01, 0x8A, 0xE8,
.platform_data = &camera_info,
},
};
+#endif /* CONFIG_I2C */
static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
.flags = SOCAM_PCLK_SAMPLE_RISING | SOCAM_HSYNC_ACTIVE_HIGH |
&ap325rxa_nor_flash_device,
&lcdc_device,
&ceu_device,
+#ifdef CONFIG_I2C
&camera_device,
+#endif
};
static struct i2c_board_info __initdata ap325rxa_i2c_devices[] = {
#include <linux/init.h>
#include <linux/types.h>
#include <linux/platform_device.h>
+#include <linux/interrupt.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/map.h>
+#include <linux/smc911x.h>
#include <asm/machvec.h>
#include <asm/io.h>
+static struct smc911x_platdata smc911x_info = {
+ .flags = SMC911X_USE_16BIT,
+ .irq_flags = IRQF_TRIGGER_LOW,
+};
+
static struct resource smc911x_resources[] = {
[0] = {
.start = 0x24000000,
.id = -1,
.num_resources = ARRAY_SIZE(smc911x_resources),
.resource = smc911x_resources,
+ .dev = {
+ .platform_data = &smc911x_info,
+ },
};
static const char *probes[] = { "cmdlinepart", NULL };
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/signal.h>
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
#include <asm/page.h>
/* Setup for the SMSC FDC37C935 / LAN91C100FD */
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
/*
* Platform Dependent Interrupt Priorities.
#include <linux/irq.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/dreamcast/sysasic.h>
+#include <mach/sysasic.h>
/* Dreamcast System ASIC Hardware Events -
#include <asm/irq.h>
#include <asm/rtc.h>
#include <asm/machvec.h>
-#include <asm/mach/sysasic.h>
+#include <mach/sysasic.h>
extern struct hw_interrupt_type systemasic_int;
extern void aica_time_init(void);
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
-#include <asm/mach/r7780rp.h>
+#include <asm/r7780rp.h>
#include <asm/push-switch.h>
static irqreturn_t psw_irq_handler(int irq, void *arg)
#include <asm/io.h>
#include <asm/hd64461.h>
#include <asm/hp6xx.h>
-#include <asm/cpu/dac.h>
+#include <cpu/dac.h>
#include <asm/pm.h>
#define STBCR 0xffffff82
*/
#include <linux/linkage.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
#define k0 r0
#define k1 r1
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/hp6xx.h>
-#include <asm/cpu/dac.h>
+#include <cpu/dac.h>
#define SCPCR 0xa4000116
#define SCPDR 0xa4000136
#include <linux/fs.h>
#include <asm/io.h>
#include <asm/uaccess.h>
-#include <asm/landisk/gio.h>
-#include <asm/landisk/iodata_landisk.h>
+#include <mach-landisk/mach/gio.h>
+#include <mach-landisk/mach/iodata_landisk.h>
#define DEVCOUNT 4
#define GIO_MINOR 2 /* GIO minor no. */
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <asm/landisk/iodata_landisk.h>
+#include <mach-landisk/mach/iodata_landisk.h>
static void disable_landisk_irq(unsigned int irq)
{
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
-#include <asm/landisk/iodata_landisk.h>
+#include <mach-landisk/mach/iodata_landisk.h>
#include <asm/push-switch.h>
static irqreturn_t psw_irq_handler(int irq, void *arg)
#include <linux/pm.h>
#include <linux/mm.h>
#include <asm/machvec.h>
-#include <asm/landisk/iodata_landisk.h>
+#include <mach-landisk/mach/iodata_landisk.h>
#include <asm/io.h>
void init_landisk_IRQ(void);
ctrl_outb(ctrl_inb(PORT_PTDR) & ~0x08, PORT_PTDR);
}
+#ifdef CONFIG_I2C
static unsigned char camera_ov772x_magic[] =
{
0x09, 0x01, 0x0c, 0x10, 0x0d, 0x41, 0x0e, 0x01,
.platform_data = &ov772x_info,
},
};
+#endif /* CONFIG_I2C */
static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
.flags = SOCAM_MASTER | SOCAM_DATAWIDTH_8 | SOCAM_PCLK_SAMPLE_RISING \
&sh_keysc_device,
&migor_lcdc_device,
&migor_ceu_device,
+#ifdef CONFIG_I2C
&migor_camera_device,
+#endif
&migor_nor_flash_device,
&migor_nand_flash_device,
};
#include <linux/kernel.h>
#include <linux/types.h>
#include <asm/io.h>
-#include <asm/se7206.h>
+#include <mach-se/mach/se7206.h>
static inline void delay(void)
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/interrupt.h>
-#include <asm/se7206.h>
+#include <mach-se/mach/se7206.h>
#define INTSTS0 0x31800000
#define INTSTS1 0x31800002
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/smc91x.h>
-#include <asm/se7206.h>
+#include <mach-se/mach/se7206.h>
#include <asm/io.h>
#include <asm/machvec.h>
#include <asm/heartbeat.h>
*/
#include <linux/kernel.h>
#include <asm/io.h>
-#include <asm/mach/se7343.h>
+#include <mach-se/mach/se7343.h>
#define badio(fn, a) panic("bad i/o operation %s for %08lx.", #fn, a)
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/se7343.h>
+#include <linux/io.h>
+#include <mach-se/mach/se7343.h>
static void disable_se7343_irq(unsigned int irq)
{
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <asm/machvec.h>
-#include <asm/mach/se7343.h>
+#include <mach-se/mach/se7343.h>
#include <asm/heartbeat.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <asm/io.h>
-#include <asm/se.h>
+#include <mach-se/mach/se.h>
/* MS7750 requires special versions of in*, out* routines, since
PC-like io ports are located at upper half byte of 16-bit word which
#include <linux/irq.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/se.h>
+#include <mach-se/mach/se.h>
static struct ipr_data ipr_irq_table[] = {
/*
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/machvec.h>
-#include <asm/se.h>
+#include <mach-se/mach/se.h>
#include <asm/io.h>
#include <asm/smc37c93x.h>
#include <asm/heartbeat.h>
.resource = heartbeat_resources,
};
+#if defined(CONFIG_CPU_SUBTYPE_SH7710) ||\
+ defined(CONFIG_CPU_SUBTYPE_SH7712)
/* SH771X Ethernet driver */
static struct resource sh_eth0_resources[] = {
[0] = {
.num_resources = ARRAY_SIZE(sh_eth1_resources),
.resource = sh_eth1_resources,
};
+#endif
static struct platform_device *se_devices[] __initdata = {
&heartbeat_device,
&cf_ide_device,
+#if defined(CONFIG_CPU_SUBTYPE_SH7710) ||\
+ defined(CONFIG_CPU_SUBTYPE_SH7712)
&sh_eth0_device,
&sh_eth1_device,
+#endif
};
static int __init se_devices_setup(void)
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <asm/se7721.h>
+#include <mach-se/mach/se7721.h>
enum {
UNUSED = 0,
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/machvec.h>
-#include <asm/se7721.h>
+#include <mach-se/mach/se7721.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/se7722.h>
+#include <mach-se/mach/se7722.h>
static void disable_se7722_irq(unsigned int irq)
{
#include <linux/smc91x.h>
#include <asm/machvec.h>
#include <asm/clock.h>
-#include <asm/se7722.h>
+#include <mach-se/mach/se7722.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <asm/sh_keysc.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <asm/io.h>
-#include <asm/se7751.h>
+#include <mach-se/mach/se7751.h>
#include <asm/addrspace.h>
static inline volatile u16 *port2adr(unsigned int port)
#include <linux/init.h>
#include <linux/irq.h>
#include <asm/irq.h>
-#include <asm/se7751.h>
+#include <mach-se/mach/se7751.h>
static struct ipr_data ipr_irq_table[] = {
{ 13, 3, 3, 2 },
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/machvec.h>
-#include <asm/se7751.h>
+#include <mach-se/mach/se7751.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/se7780.h>
+#include <mach-se/mach/se7780.h>
/*
* Initialize IRQ setting
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/machvec.h>
-#include <asm/se7780.h>
+#include <mach-se/mach/se7780.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
--- /dev/null
+obj-$(CONFIG_SH_7619_SOLUTION_ENGINE) += board-se7619.o
+
+obj-$(CONFIG_SH_SOLUTION_ENGINE) += 770x/
+obj-$(CONFIG_SH_7206_SOLUTION_ENGINE) += 7206/
+obj-$(CONFIG_SH_7722_SOLUTION_ENGINE) += 7722/
+obj-$(CONFIG_SH_7751_SOLUTION_ENGINE) += 7751/
+obj-$(CONFIG_SH_7780_SOLUTION_ENGINE) += 7780/
+obj-$(CONFIG_SH_7343_SOLUTION_ENGINE) += 7343/
+obj-$(CONFIG_SH_7721_SOLUTION_ENGINE) += 7721/
#include <linux/platform_device.h>
#include <asm/io.h>
#include <asm/rtc.h>
-#include <asm/sh03/io.h>
-#include <asm/sh03/sh03.h>
+#include <mach-sh03/mach/io.h>
+#include <mach-sh03/mach/sh03.h>
#include <asm/addrspace.h>
static void __init init_sh03_IRQ(void)
#include <asm/snapgear.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/cpu/timer.h>
+#include <cpu/timer.h>
/*
* EraseConfig handling functions
#include <linux/init.h>
#include <linux/irq.h>
+#include <linux/interrupt.h>
-#include <linux/hdreg.h>
-#include <linux/ide.h>
#include <asm/io.h>
#include <asm/systemh7751.h>
#include <asm/smc37c93x.h>
+++ /dev/null
-if SH_MAGIC_PANEL_R2
-
-menu "Magic Panel R2 options"
-
-config SH_MAGIC_PANEL_R2_VERSION
- int SH_MAGIC_PANEL_R2_VERSION
- default "3"
- help
- Set the version of the Magic Panel R2
-
-endmenu
-
-endif
+++ /dev/null
-#
-# Makefile for the Magic Panel specific parts
-#
-
-obj-y := setup.o
\ No newline at end of file
+++ /dev/null
-obj-y := setup.o
+++ /dev/null
-obj-y := setup.o
+++ /dev/null
-obj-y := setup.o
+++ /dev/null
-#
-# Makefile for the 7619 SolutionEngine specific parts of the kernel
-#
-
-obj-y := setup.o
+++ /dev/null
-#
-# Makefile for the SHMIN board.
-#
-
-obj-y := setup.o
CONFIG_MEMORY_START ?= 0x0c000000
CONFIG_BOOT_LINK_OFFSET ?= 0x00800000
CONFIG_ZERO_PAGE_OFFSET ?= 0x00001000
+CONFIG_ENTRY_OFFSET ?= 0x00001000
export CONFIG_PAGE_OFFSET CONFIG_MEMORY_START CONFIG_BOOT_LINK_OFFSET \
- CONFIG_ZERO_PAGE_OFFSET
+ CONFIG_ZERO_PAGE_OFFSET CONFIG_ENTRY_OFFSET
targets := zImage vmlinux.srec uImage uImage.srec
subdir- := compressed
* Copyright (C) 2002 Stuart Menefy (stuart.menefy@st.com)
*/
#include <asm/cache.h>
-#include <asm/cpu/mmu_context.h>
-#include <asm/cpu/registers.h>
+#include <cpu/mmu_context.h>
+#include <cpu/registers.h>
/*
* Fixed TLB entries to identity map the beginning of RAM
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Wed Jun 4 17:30:00 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:18:59 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_PAGE_SIZE_8KB is not set
# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc7
-# Fri Sep 21 15:46:27 2007
+# Linux kernel version: 2.6.27-rc1
+# Mon Aug 4 16:49:13 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_TIME=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+CONFIG_PROFILING=y
+# CONFIG_MARKERS is not set
+# CONFIG_OPROFILE is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
CONFIG_CPU_SH4=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
CONFIG_CPU_SUBTYPE_SH7091=y
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x0c000000
CONFIG_MEMORY_SIZE=0x01000000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_HUGETLB_PAGE_SIZE_64K=y
# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
# CONFIG_HUGETLB_PAGE_SIZE_4MB is not set
# CONFIG_HUGETLB_PAGE_SIZE_64MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_512MB is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
+CONFIG_SECCOMP=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_PREEMPT_BKL=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
CONFIG_SH_PCIDMA_NONCOHERENT=y
CONFIG_PCI_AUTO=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+CONFIG_PCI_LEGACY=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
-
-#
-# Networking
-#
CONFIG_NET=y
#
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
+CONFIG_GDROM=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_NETLINK is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
+# CONFIG_FUSION is not set
#
-# Fusion MPT device support
+# IEEE 1394 (FireWire) support
#
-# CONFIG_FUSION is not set
#
-# IEEE 1394 (FireWire) support
+# Enable only one of the two stacks, unless you know what you are doing
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
+# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_MAPLE=y
+# CONFIG_KEYBOARD_SH_KEYSC is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+# CONFIG_SPI is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set
-CONFIG_HW_RANDOM=y
-# CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-CONFIG_DEVPORT=y
-# CONFIG_I2C is not set
#
-# SPI support
+# Sonics Silicon Backplane
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
+# CONFIG_VIDEO_MEDIA is not set
#
-# Graphics support
+# Multimedia drivers
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DAB is not set
#
-# Display device support
+# Graphics support
#
-# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+# CONFIG_FB_SH_MOBILE_LCDC is not set
# CONFIG_FB_VIRTUAL is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
# CONFIG_LOGO_SUPERH_MONO is not set
# CONFIG_LOGO_SUPERH_VGA16 is not set
CONFIG_LOGO_SUPERH_CLUT224=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-
-#
-# USB Gadget Support
-#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+# CONFIG_DNOTIFY is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_SMB_FS is not set
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-#
-# Profiling support
-#
-CONFIG_PROFILING=y
-# CONFIG_OPROFILE is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_SH_KGDB is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
-# CONFIG_CRYPTO is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc4
-# Tue Sep 11 19:42:44 2007
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:24:57 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# CONFIG_SYSVIPC is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
-# CONFIG_USER_NS is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
CONFIG_CPU_SH3=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x0d000000
CONFIG_MEMORY_SIZE=0x00400000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
#
CONFIG_ISA=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=y
#
# Power management options (EXPERIMENTAL)
#
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_PM=y
-CONFIG_PM_LEGACY=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
CONFIG_APM_EMULATION=y
#
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_PAS16 is not set
-# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
+CONFIG_ATA_SFF=y
+# CONFIG_SATA_MV is not set
# CONFIG_PATA_LEGACY is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_QDI is not set
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
-CONFIG_INPUT_TSDEV=y
-CONFIG_INPUT_TSDEV_SCREEN_X=240
-CONFIG_INPUT_TSDEV_SCREEN_Y=320
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
+# CONFIG_INPUT_APMPOWER is not set
#
# Input Device Drivers
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_KEYBOARD_HP6XX=y
+# CONFIG_KEYBOARD_SH_KEYSC is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
CONFIG_TOUCHSCREEN_HP600=y
+# CONFIG_TOUCHSCREEN_HTCPEN is not set
# CONFIG_TOUCHSCREEN_PENMOUNT is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_UCB1400 is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=64
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
-# CONFIG_DAB is not set
+# CONFIG_VIDEO_MEDIA is not set
#
-# Graphics support
+# Multimedia drivers
#
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_HP680=y
+# CONFIG_DAB is not set
#
-# Display device support
+# Graphics support
#
-# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=y
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
#
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_HIT=y
+CONFIG_FB_SH_MOBILE_LCDC=y
# CONFIG_FB_VIRTUAL is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_CORGI is not set
+CONFIG_BACKLIGHT_HP680=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
# CONFIG_LOGO is not set
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
#
# Platform RTC drivers
#
+# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_SH_KGDB is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=y
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-# CONFIG_CRYPTO_DES is not set
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_LZO is not set
# CONFIG_CRYPTO_HW is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.19
-# Thu Dec 7 17:13:04 2006
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:35:07 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_SYS_SUPPORTS_PCI=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
-CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_NAMESPACES is not set
+# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
-# CONFIG_SH_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SOLUTION_ENGINE is not set
-# CONFIG_SH_7300_SOLUTION_ENGINE is not set
-# CONFIG_SH_7343_SOLUTION_ENGINE is not set
-# CONFIG_SH_73180_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SYSTEMH is not set
-# CONFIG_SH_HP6XX is not set
-# CONFIG_SH_EC3104 is not set
-# CONFIG_SH_SATURN is not set
-# CONFIG_SH_DREAMCAST is not set
-# CONFIG_SH_BIGSUR is not set
-# CONFIG_SH_MPC1211 is not set
-# CONFIG_SH_SH03 is not set
-# CONFIG_SH_SECUREEDGE5410 is not set
-# CONFIG_SH_HS7751RVOIP is not set
-# CONFIG_SH_7710VOIPGW is not set
-# CONFIG_SH_RTS7751R2D is not set
-# CONFIG_SH_R7780RP is not set
-# CONFIG_SH_EDOSK7705 is not set
-# CONFIG_SH_SH4202_MICRODEV is not set
-CONFIG_SH_LANDISK=y
-# CONFIG_SH_TITAN is not set
-# CONFIG_SH_SHMIN is not set
-# CONFIG_SH_7206_SOLUTION_ENGINE is not set
-# CONFIG_SH_7619_SOLUTION_ENGINE is not set
-# CONFIG_SH_UNKNOWN is not set
-
-#
-# Processor selection
-#
CONFIG_CPU_SH4=y
-
-#
-# SH-2 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7604 is not set
# CONFIG_CPU_SUBTYPE_SH7619 is not set
-
-#
-# SH-2A Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
-
-#
-# SH-3 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7300 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7708 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
-
-#
-# SH-4 Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7712 is not set
+# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
CONFIG_CPU_SUBTYPE_SH7751R=y
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-
-#
-# ST40 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
-
-#
-# SH-4A Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
-
-#
-# SH4AL-DSP Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
+# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
#
+CONFIG_QUICKLIST=y
CONFIG_MMU=y
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x0c000000
CONFIG_MEMORY_SIZE=0x04000000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_DEFAULT=y
+CONFIG_MAX_ACTIVE_REGIONS=1
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
#
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
-# CONFIG_SH_WRITETHROUGH is not set
-# CONFIG_SH_OCRAM is not set
+CONFIG_CACHE_WRITEBACK=y
+# CONFIG_CACHE_WRITETHROUGH is not set
+# CONFIG_CACHE_OFF is not set
#
# Processor features
CONFIG_CPU_LITTLE_ENDIAN=y
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_SH_FPU=y
-# CONFIG_SH_DSP is not set
# CONFIG_SH_STORE_QUEUES is not set
CONFIG_CPU_HAS_INTEVT=y
-CONFIG_CPU_HAS_INTC_IRQ=y
CONFIG_CPU_HAS_SR_RB=y
CONFIG_CPU_HAS_PTEA=y
+CONFIG_CPU_HAS_FPU=y
#
-# Timer support
+# Board support
+#
+# CONFIG_SH_7751_SYSTEMH is not set
+# CONFIG_SH_SECUREEDGE5410 is not set
+# CONFIG_SH_RTS7751R2D is not set
+CONFIG_SH_LANDISK=y
+# CONFIG_SH_TITAN is not set
+# CONFIG_SH_LBOX_RE2 is not set
+
+#
+# Timer and clock configuration
#
CONFIG_SH_TMU=y
CONFIG_SH_TIMER_IRQ=16
CONFIG_SH_PCLK_FREQ=33333333
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
# Companion Chips
#
-# CONFIG_HD6446X_SERIES is not set
-CONFIG_HEARTBEAT=y
#
# Additional SuperH Device Drivers
#
+CONFIG_HEARTBEAT=y
# CONFIG_PUSH_SWITCH is not set
#
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
CONFIG_KEXEC=y
-# CONFIG_SMP is not set
+# CONFIG_CRASH_DUMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
#
# Bus options
#
-CONFIG_ISA=y
CONFIG_PCI=y
CONFIG_SH_PCIDMA_NONCOHERENT=y
CONFIG_PCI_AUTO=y
CONFIG_PCI_AUTO_UPDATE_RESOURCES=y
-# CONFIG_PCI_MULTITHREAD_PROBE is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=y
CONFIG_YENTA_TOSHIBA=y
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
-# CONFIG_I82365 is not set
-# CONFIG_TCIC is not set
-CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=y
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_FLAT is not set
# CONFIG_BINFMT_MISC is not set
-#
-# Power management options (EXPERIMENTAL)
-#
-# CONFIG_PM is not set
-
#
# Networking
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
#
# Core Netfilter Configuration
#
-# CONFIG_NETFILTER_NETLINK is not set
-# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
# CONFIG_NETFILTER_XTABLES is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_QUEUE=m
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNP is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_CPQ_DA is not set
+CONFIG_BLK_DEV=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=4
CONFIG_BLK_DEV_IDE=y
#
-# Please see Documentation/ide.txt for help/info on IDE drives
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
+CONFIG_IDE_ATAPI=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDECS is not set
+# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
#
-CONFIG_IDE_GENERIC=y
+# CONFIG_BLK_DEV_PLATFORM is not set
+CONFIG_BLK_DEV_IDEDMA_SFF=y
+
+#
+# PCI IDE chipsets support
+#
CONFIG_BLK_DEV_IDEPCI=y
-CONFIG_IDEPCI_SHARE_IRQ=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
-# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-CONFIG_IDEDMA_PCI_AUTO=y
-CONFIG_IDEDMA_ONLYDISK=y
CONFIG_BLK_DEV_AEC62XX=y
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
-# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
-# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
-# CONFIG_IDE_ARM is not set
-# CONFIG_IDE_CHIPSETS is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDEDMA=y
-# CONFIG_IDEDMA_IVB is not set
-CONFIG_IDEDMA_AUTO=y
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
-# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
-
-#
-# SCSI low-level drivers
-#
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
-# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
-# CONFIG_SCSI_DPT_I2O is not set
-# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
-# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
-# CONFIG_SCSI_GENERIC_NCR5380 is not set
-# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_NCR53C406A is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
-# CONFIG_SCSI_PAS16 is not set
-# CONFIG_SCSI_PSI240I is not set
-# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
-# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
-# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# PCMCIA SCSI adapter support
-#
-# CONFIG_PCMCIA_AHA152X is not set
-# CONFIG_PCMCIA_FDOMAIN is not set
-# CONFIG_PCMCIA_NINJA_SCSI is not set
-# CONFIG_PCMCIA_QLOGIC is not set
-# CONFIG_PCMCIA_SYM53C500 is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
+# CONFIG_SCSI_DH is not set
# CONFIG_ATA is not set
-
-#
-# Old CD-ROM drivers (not SCSI, not IDE)
-#
-# CONFIG_CD_NO_IDESCSI is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set
-
-#
-# Fusion MPT device support
-#
# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
-# CONFIG_IEEE1394 is not set
#
-# I2O device support
+# Enable only one of the two stacks, unless you know what you are doing
#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
-
-#
-# Network device support
-#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
-
-#
-# ARCnet devices
-#
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_SMC91X is not set
-# CONFIG_NET_VENDOR_RACAL is not set
-
-#
-# Tulip family network device support
-#
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
-# CONFIG_AT1700 is not set
-# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
-# CONFIG_NET_ISA is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
-# CONFIG_AC3200 is not set
-# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_CS89x0 is not set
-# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NE2K_PCI is not set
CONFIG_8139CP=y
# CONFIG_8139TOO is not set
+# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+# CONFIG_SC92031 is not set
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_NIU is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
+# Wireless LAN
#
-# CONFIG_NET_RADIO is not set
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
-# PCMCIA network device support
+# USB Network Adapters
#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+# CONFIG_USB_USBNET is not set
# CONFIG_NET_PCMCIA is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
#
# PCMCIA character devices
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
+# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
-CONFIG_VIDEO_DEV=m
-CONFIG_VIDEO_V4L1=y
-CONFIG_VIDEO_V4L1_COMPAT=y
-CONFIG_VIDEO_V4L2=y
#
-# Video Capture Adapters
+# Multimedia core support
#
+CONFIG_VIDEO_DEV=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VIDEO_ALLOW_V4L1=y
+CONFIG_VIDEO_V4L1_COMPAT=y
+# CONFIG_DVB_CORE is not set
+CONFIG_VIDEO_MEDIA=m
#
-# Video Capture Adapters
+# Multimedia drivers
#
+# CONFIG_MEDIA_ATTACH is not set
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L1=m
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
# CONFIG_VIDEO_ADV_DEBUG is not set
CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
# CONFIG_VIDEO_VIVI is not set
-# CONFIG_VIDEO_PMS is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_CPIA2 is not set
-# CONFIG_VIDEO_STRADIS is not set
-
-#
-# V4L USB devices
-#
+CONFIG_V4L_USB_DRIVERS=y
+# CONFIG_USB_VIDEO_CLASS is not set
+# CONFIG_USB_GSPCA is not set
CONFIG_VIDEO_USBVIDEO=m
CONFIG_USB_VICAM=m
CONFIG_USB_IBMCAM=m
# CONFIG_USB_ZC0301 is not set
CONFIG_USB_PWC=m
# CONFIG_USB_PWC_DEBUG is not set
-
-#
-# Radio Adapters
-#
-# CONFIG_RADIO_CADET is not set
-# CONFIG_RADIO_RTRACK is not set
-# CONFIG_RADIO_RTRACK2 is not set
-# CONFIG_RADIO_AZTECH is not set
-# CONFIG_RADIO_GEMTEK is not set
+# CONFIG_USB_ZR364XX is not set
+# CONFIG_USB_STKWEBCAM is not set
+# CONFIG_USB_S2255 is not set
+# CONFIG_SOC_CAMERA is not set
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
+CONFIG_RADIO_ADAPTERS=y
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set
-# CONFIG_RADIO_SF16FMI is not set
-# CONFIG_RADIO_SF16FMR2 is not set
-# CONFIG_RADIO_TERRATEC is not set
-# CONFIG_RADIO_TRUST is not set
-# CONFIG_RADIO_TYPHOON is not set
-# CONFIG_RADIO_ZOLTRIX is not set
CONFIG_USB_DSBR=m
+# CONFIG_USB_SI470X is not set
+# CONFIG_DAB is not set
#
-# Digital Video Broadcasting Devices
+# Graphics support
#
-# CONFIG_DVB is not set
-CONFIG_USB_DABUSB=m
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Graphics support
+# Display device support
#
-CONFIG_FIRMWARE_EDID=y
-# CONFIG_FB is not set
+# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
#
-# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FONT_8x16=y
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Sound
-#
CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
# CONFIG_SND is not set
+CONFIG_SOUND_PRIME=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
#
-# Open Sound System
+# USB Input Devices
#
-CONFIG_SOUND_PRIME=m
-# CONFIG_OSS_OBSOLETE_DRIVER is not set
-# CONFIG_SOUND_BT878 is not set
-# CONFIG_SOUND_ES1371 is not set
-# CONFIG_SOUND_ICH is not set
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
-# CONFIG_SOUND_VIA82CXXX is not set
+CONFIG_USB_HID=m
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
#
-# USB support
+# USB HID Boot Protocol drivers
#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-# CONFIG_USB_BANDWIDTH is not set
+CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=y
-# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
-# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
-#
-# USB Input Devices
-#
-CONFIG_USB_HID=m
-CONFIG_USB_HIDINPUT=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
-# CONFIG_USB_HIDDEV is not set
-
-#
-# USB HID Boot Protocol drivers
-#
-# CONFIG_USB_KBD is not set
-# CONFIG_USB_MOUSE is not set
-# CONFIG_USB_AIPTEK is not set
-# CONFIG_USB_WACOM is not set
-# CONFIG_USB_ACECAD is not set
-# CONFIG_USB_KBTAB is not set
-# CONFIG_USB_POWERMATE is not set
-# CONFIG_USB_TOUCHSCREEN is not set
-# CONFIG_USB_YEALINK is not set
-# CONFIG_USB_XPAD is not set
-# CONFIG_USB_ATI_REMOTE is not set
-# CONFIG_USB_ATI_REMOTE2 is not set
-# CONFIG_USB_KEYSPAN_REMOTE is not set
-# CONFIG_USB_APPLETOUCH is not set
-
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-
-#
-# USB Network Adapters
-#
-# CONFIG_USB_CATC is not set
-# CONFIG_USB_KAWETH is not set
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_RTL8150=m
-# CONFIG_USB_USBNET_MII is not set
-# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# USB port drivers
#
-
-#
-# USB Serial Converter support
-#
CONFIG_USB_SERIAL=m
+# CONFIG_USB_EZUSB is not set
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_AIRCABLE is not set
-# CONFIG_USB_SERIAL_AIRPRIME is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP2101 is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
+# CONFIG_USB_SERIAL_IUU is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_MOS7720 is not set
# CONFIG_USB_SERIAL_MOS7840 is not set
+# CONFIG_USB_SERIAL_MOTOROLA is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
CONFIG_USB_SERIAL_PL2303=m
+# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
CONFIG_USB_SISUSBVGA_CON=y
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
-
-#
-# USB DSL modem support
-#
-
-#
-# USB Gadget Support
-#
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
#
# File systems
# CONFIG_EXT3_FS_SECURITY is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-CONFIG_ROMFS_FS=y
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_NFSD_TCP=y
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
+# CONFIG_DLM is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
-# CONFIG_KGDB is not set
+# CONFIG_SH_KGDB is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
#
-# Cryptographic options
+# Compression
#
-# CONFIG_CRYPTO is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
+CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21-rc4
-# Sat Mar 24 22:04:27 2007
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:39:41 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_SYS_SUPPORTS_PCI=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
-# CONFIG_SH_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SOLUTION_ENGINE is not set
-# CONFIG_SH_7300_SOLUTION_ENGINE is not set
-# CONFIG_SH_7343_SOLUTION_ENGINE is not set
-# CONFIG_SH_73180_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SYSTEMH is not set
-# CONFIG_SH_HP6XX is not set
-# CONFIG_SH_SATURN is not set
-# CONFIG_SH_DREAMCAST is not set
-# CONFIG_SH_MPC1211 is not set
-# CONFIG_SH_SH03 is not set
-# CONFIG_SH_SECUREEDGE5410 is not set
-# CONFIG_SH_HS7751RVOIP is not set
-# CONFIG_SH_7710VOIPGW is not set
-# CONFIG_SH_RTS7751R2D is not set
-# CONFIG_SH_HIGHLANDER is not set
-# CONFIG_SH_EDOSK7705 is not set
-# CONFIG_SH_SH4202_MICRODEV is not set
-# CONFIG_SH_LANDISK is not set
-# CONFIG_SH_TITAN is not set
-# CONFIG_SH_SHMIN is not set
-# CONFIG_SH_7206_SOLUTION_ENGINE is not set
-# CONFIG_SH_7619_SOLUTION_ENGINE is not set
-CONFIG_SH_LBOX_RE2=y
-# CONFIG_SH_UNKNOWN is not set
-
-#
-# Processor selection
-#
CONFIG_CPU_SH4=y
-
-#
-# SH-2 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7604 is not set
# CONFIG_CPU_SUBTYPE_SH7619 is not set
-
-#
-# SH-2A Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
-
-#
-# SH-3 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7300 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7708 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
-
-#
-# SH-4 Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7712 is not set
+# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
CONFIG_CPU_SUBTYPE_SH7751R=y
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-
-#
-# ST40 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
-
-#
-# SH-4A Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
-
-#
-# SH4AL-DSP Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
#
+CONFIG_QUICKLIST=y
CONFIG_MMU=y
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x0c000000
CONFIG_MEMORY_SIZE=0x04000000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_DEFAULT=y
+CONFIG_MAX_ACTIVE_REGIONS=1
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
#
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
-# CONFIG_SH_WRITETHROUGH is not set
-# CONFIG_SH_OCRAM is not set
+CONFIG_CACHE_WRITEBACK=y
+# CONFIG_CACHE_WRITETHROUGH is not set
+# CONFIG_CACHE_OFF is not set
#
# Processor features
CONFIG_CPU_LITTLE_ENDIAN=y
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_SH_FPU=y
-# CONFIG_SH_DSP is not set
# CONFIG_SH_STORE_QUEUES is not set
CONFIG_CPU_HAS_INTEVT=y
-CONFIG_CPU_HAS_INTC_IRQ=y
CONFIG_CPU_HAS_SR_RB=y
CONFIG_CPU_HAS_PTEA=y
+CONFIG_CPU_HAS_FPU=y
+
+#
+# Board support
+#
+# CONFIG_SH_7751_SYSTEMH is not set
+# CONFIG_SH_SECUREEDGE5410 is not set
+# CONFIG_SH_RTS7751R2D is not set
+# CONFIG_SH_LANDISK is not set
+# CONFIG_SH_TITAN is not set
+CONFIG_SH_LBOX_RE2=y
#
# Timer and clock configuration
CONFIG_SH_TMU=y
CONFIG_SH_TIMER_IRQ=16
CONFIG_SH_PCLK_FREQ=40000000
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
# Companion Chips
#
-# CONFIG_HD6446X_SERIES is not set
#
# Additional SuperH Device Drivers
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
CONFIG_KEXEC=y
-# CONFIG_SMP is not set
+# CONFIG_CRASH_DUMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
#
# Bus options
#
-CONFIG_ISA=y
CONFIG_PCI=y
CONFIG_SH_PCIDMA_NONCOHERENT=y
CONFIG_PCI_AUTO=y
CONFIG_PCI_AUTO_UPDATE_RESOURCES=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
CONFIG_PCCARD=y
CONFIG_PCMCIA_DEBUG=y
CONFIG_PCMCIA=y
# CONFIG_YENTA_TOSHIBA is not set
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
-# CONFIG_I82365 is not set
-# CONFIG_TCIC is not set
-CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=y
-
-#
-# PCI Hotplug Support
-#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_FLAT is not set
# CONFIG_BINFMT_MISC is not set
-#
-# Power management options (EXPERIMENTAL)
-#
-# CONFIG_PM is not set
-
#
# Networking
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
-
-#
-# IP: Virtual Server Configuration
-#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
#
# Core Netfilter Configuration
#
-# CONFIG_NETFILTER_NETLINK is not set
-# CONFIG_NF_CONNTRACK_ENABLED is not set
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
# CONFIG_NETFILTER_XTABLES is not set
#
# CONFIG_IP_NF_QUEUE is not set
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_ARPTABLES is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNP is not set
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_CPQ_DA is not set
+CONFIG_BLK_DEV=y
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
-# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
-
-#
-# SCSI low-level drivers
-#
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
-# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
-# CONFIG_SCSI_DPT_I2O is not set
-# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
-# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
-# CONFIG_SCSI_GENERIC_NCR5380 is not set
-# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_NCR53C406A is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
-# CONFIG_SCSI_PAS16 is not set
-# CONFIG_SCSI_PSI240I is not set
-# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
-# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
-# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
-
-#
-# PCMCIA SCSI adapter support
-#
-# CONFIG_PCMCIA_AHA152X is not set
-# CONFIG_PCMCIA_FDOMAIN is not set
-# CONFIG_PCMCIA_NINJA_SCSI is not set
-# CONFIG_PCMCIA_QLOGIC is not set
-# CONFIG_PCMCIA_SYM53C500 is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_JMICRON is not set
-# CONFIG_PATA_LEGACY is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC_OLD is not set
-# CONFIG_PATA_QDI is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
-# CONFIG_PATA_WINBOND_VLB is not set
CONFIG_PATA_PLATFORM=y
-
-#
-# Old CD-ROM drivers (not SCSI, not IDE)
-#
-# CONFIG_CD_NO_IDESCSI is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
-# CONFIG_IEEE1394 is not set
#
-# I2O device support
+# Enable only one of the two stacks, unless you know what you are doing
#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
-
-#
-# Network device support
-#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
# CONFIG_PHYLIB is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_SMC91X is not set
-# CONFIG_NET_VENDOR_RACAL is not set
-
-#
-# Tulip family network device support
-#
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
-# CONFIG_AT1700 is not set
-# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
-# CONFIG_NET_ISA is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
-# CONFIG_AC3200 is not set
-# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_CS89x0 is not set
-# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
CONFIG_8139TOO_TUNE_TWISTER=y
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
+# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
-
-#
-# Ethernet (1000 Mbit)
-#
+CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
+# CONFIG_ATL1E is not set
+CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
+# CONFIG_NIU is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# PCMCIA network device support
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
CONFIG_NET_PCMCIA=y
# CONFIG_PCMCIA_3C589 is not set
# CONFIG_PCMCIA_3C574 is not set
# CONFIG_PCMCIA_SMC91C92 is not set
# CONFIG_PCMCIA_XIRC2PS is not set
# CONFIG_PCMCIA_AXNET is not set
-
-#
-# Wan interfaces
-#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
#
# PCMCIA character devices
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
+CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
+# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
#
-# Digital Video Broadcasting Devices
+# Multimedia drivers
#
-# CONFIG_DVB is not set
+# CONFIG_DAB is not set
#
# Graphics support
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Console display driver support
+# Display device support
#
-# CONFIG_MDA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
+# CONFIG_DISPLAY_SUPPORT is not set
#
-# Sound
+# Console display driver support
#
+CONFIG_DUMMY_CONSOLE=y
# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
+CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-
-#
-# USB Gadget Support
-#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
-
-#
-# RTC drivers
-#
-# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_DS1742 is not set
-# CONFIG_RTC_DRV_M48T86 is not set
-# CONFIG_RTC_DRV_SH is not set
# CONFIG_RTC_DRV_TEST is not set
-# CONFIG_RTC_DRV_V3020 is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
#
-# DMA Devices
+# SPI RTC drivers
#
#
-# Auxiliary Display support
+# Platform RTC drivers
#
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
#
-# Virtualization
+# on-CPU RTC drivers
#
+# CONFIG_RTC_DRV_SH is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
#
# File systems
# CONFIG_EXT3_FS_SECURITY is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-CONFIG_ROMFS_FS=y
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_SMB_FS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
#
-# Cryptographic options
+# Compression
#
-# CONFIG_CRYPTO is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc2
-# Fri Aug 17 12:15:16 2007
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:41:08 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
CONFIG_AUDIT=y
+# CONFIG_AUDITSYSCALL is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_RELAY=y
+# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
CONFIG_CPU_SH3=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
CONFIG_CPU_SUBTYPE_SH7720=y
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x0C000000
CONFIG_MEMORY_SIZE=0x03F00000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_SH_DSP=y
CONFIG_SH_ADC=y
CONFIG_CPU_HAS_INTEVT=y
-CONFIG_CPU_HAS_INTC_IRQ=y
CONFIG_CPU_HAS_SR_RB=y
CONFIG_CPU_HAS_DSP=y
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
# Bus options
#
# CONFIG_ARCH_SUPPORTS_MSI is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
# CONFIG_PCCARD is not set
#
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
CONFIG_MTD_PHYSMAP_START=0x0000000
CONFIG_MTD_PHYSMAP_LEN=0
CONFIG_MTD_PHYSMAP_BANKWIDTH=0
-# CONFIG_MTD_SOLUTIONENGINE is not set
# CONFIG_MTD_PLATRAM is not set
#
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
# CONFIG_SMC91X is not set
CONFIG_SMC911X=y
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SH_KEYSC is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
CONFIG_DAB=y
#
# Graphics support
#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
# CONFIG_RTC_HCTOSYS is not set
#
# Platform RTC drivers
#
+# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_EXT3_FS_XATTR is not set
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_JFFS2_FS_XATTR is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-CONFIG_SUNRPC_BIND34=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_FORCED_INLINING is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xa4430000
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
+# CONFIG_IRQSTACKS is not set
CONFIG_SH_KGDB=y
#
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18
-# Tue Oct 3 11:27:01 2006
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:47:16 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
CONFIG_SHMEM=y
-CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
-# CONFIG_SH_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SOLUTION_ENGINE is not set
-# CONFIG_SH_7300_SOLUTION_ENGINE is not set
-# CONFIG_SH_7343_SOLUTION_ENGINE is not set
-# CONFIG_SH_73180_SOLUTION_ENGINE is not set
-# CONFIG_SH_7751_SYSTEMH is not set
-# CONFIG_SH_HP6XX is not set
-# CONFIG_SH_EC3104 is not set
-# CONFIG_SH_SATURN is not set
-# CONFIG_SH_DREAMCAST is not set
-# CONFIG_SH_BIGSUR is not set
-# CONFIG_SH_MPC1211 is not set
-# CONFIG_SH_SH03 is not set
-# CONFIG_SH_SECUREEDGE5410 is not set
-# CONFIG_SH_HS7751RVOIP is not set
-# CONFIG_SH_7710VOIPGW is not set
-# CONFIG_SH_RTS7751R2D is not set
-# CONFIG_SH_R7780RP is not set
-# CONFIG_SH_EDOSK7705 is not set
-CONFIG_SH_SH4202_MICRODEV=y
-# CONFIG_SH_LANDISK is not set
-# CONFIG_SH_TITAN is not set
-# CONFIG_SH_SHMIN is not set
-# CONFIG_SH_UNKNOWN is not set
-
-#
-# Processor selection
-#
CONFIG_CPU_SH4=y
-
-#
-# SH-2 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7604 is not set
-
-#
-# SH-3 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH7300 is not set
+# CONFIG_CPU_SUBTYPE_SH7619 is not set
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
+# CONFIG_CPU_SUBTYPE_SH7206 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7708 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
-
-#
-# SH-4 Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7712 is not set
+# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
CONFIG_CPU_SUBTYPE_SH4_202=y
-
-#
-# ST40 Processor Support
-#
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
-
-#
-# SH-4A Processor Support
-#
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
-
-#
-# SH4AL-DSP Processor Support
-#
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SH7785 is not set
+# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
+# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
#
+CONFIG_QUICKLIST=y
CONFIG_MMU=y
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x08000000
CONFIG_MEMORY_SIZE=0x04000000
+CONFIG_29BIT=y
CONFIG_VSYSCALL=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SPARSEMEM_DEFAULT=y
+CONFIG_MAX_ACTIVE_REGIONS=1
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
+# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_HUGETLB_PAGE_SIZE_64K=y
+# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_4MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_64MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_512MB is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_NR_QUICK=2
#
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
-CONFIG_SH_WRITETHROUGH=y
-# CONFIG_SH_OCRAM is not set
+CONFIG_CACHE_WRITEBACK=y
+# CONFIG_CACHE_WRITETHROUGH is not set
+# CONFIG_CACHE_OFF is not set
#
# Processor features
#
CONFIG_CPU_LITTLE_ENDIAN=y
+# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_SH_FPU=y
-# CONFIG_SH_DSP is not set
# CONFIG_SH_STORE_QUEUES is not set
CONFIG_CPU_HAS_INTEVT=y
CONFIG_CPU_HAS_SR_RB=y
+CONFIG_CPU_HAS_PTEA=y
+CONFIG_CPU_HAS_FPU=y
#
-# Timer support
+# Board support
+#
+CONFIG_SH_SH4202_MICRODEV=y
+
+#
+# Timer and clock configuration
#
CONFIG_SH_TMU=y
+CONFIG_SH_TIMER_IRQ=16
CONFIG_SH_PCLK_FREQ=66000000
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
# DMA support
#
+CONFIG_SH_DMA_API=y
CONFIG_SH_DMA=y
CONFIG_NR_ONCHIP_DMA_CHANNELS=4
# CONFIG_NR_DMA_CHANNELS_BOOL is not set
#
# Companion Chips
#
-# CONFIG_HD6446X_SERIES is not set
+
+#
+# Additional SuperH Device Drivers
+#
CONFIG_HEARTBEAT=y
+# CONFIG_PUSH_SWITCH is not set
#
# Kernel features
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
-# CONFIG_SMP is not set
+# CONFIG_CRASH_DUMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_PREEMPT_BKL=y
+# CONFIG_PREEMPT_RCU is not set
+CONFIG_GUSA=y
+# CONFIG_GUSA_RB is not set
#
# Boot options
# Bus options
#
CONFIG_SUPERHYWAY=y
-# CONFIG_PCI is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+# CONFIG_ARCH_SUPPORTS_MSI is not set
# CONFIG_PCCARD is not set
-#
-# PCI Hotplug Support
-#
-
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_FLAT is not set
# CONFIG_BINFMT_MISC is not set
-#
-# Power management options (EXPERIMENTAL)
-#
-# CONFIG_PM is not set
-
#
# Networking
#
#
# Networking options
#
-# CONFIG_NETDEBUG is not set
# CONFIG_PACKET is not set
# CONFIG_UNIX is not set
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
#
# Device Drivers
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-
-#
-# Block devices
-#
+CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-CONFIG_BLK_DEV_INITRD=y
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=1
CONFIG_BLK_DEV_IDE=y
#
-# Please see Documentation/ide.txt for help/info on IDE drives
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
#
# IDE chipset support/bugfixes
#
-CONFIG_IDE_GENERIC=y
-# CONFIG_IDE_ARM is not set
+# CONFIG_BLK_DEV_PLATFORM is not set
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_IDEDMA_AUTO is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-
-#
-# I2O device support
-#
-
-#
-# Network device support
-#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
-
-#
-# PHY device support
-#
+# CONFIG_VETH is not set
# CONFIG_PHYLIB is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
CONFIG_SMC91X=y
+# CONFIG_SMC911X is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+CONFIG_NETDEV_10000=y
#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
+# Wireless LAN
#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
# Character devices
#
# CONFIG_VT is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
-
-#
-# I2C support
-#
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
-
-#
-# Hardware Monitoring support
-#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
#
-# Misc devices
+# Sonics Silicon Backplane
#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
#
-# Digital Video Broadcasting Devices
+# Multimedia drivers
#
-# CONFIG_DVB is not set
+# CONFIG_DAB is not set
#
# Graphics support
#
-CONFIG_FIRMWARE_EDID=y
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Sound
+# Display device support
#
+# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_SOUND is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-
-#
-# USB Gadget Support
-#
# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
#
# File systems
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
# CONFIG_NLS_CODEPAGE_437 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
+# CONFIG_DLM is not set
#
# Kernel hacking
#
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_UNWIND_INFO is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_KGDB is not set
+# CONFIG_SH_KGDB is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
#
-# Cryptographic options
+# Crypto core or helper
#
-CONFIG_CRYPTO=y
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=y
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
#
-# Hardware crypto devices
+# Compression
#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
#
# Library routines
#
+CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc3
-# Thu May 22 14:30:07 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:44:41 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODULE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
#
# CONFIG_SH_7722_SOLUTION_ENGINE is not set
CONFIG_SH_MIGOR=y
+CONFIG_SH_MIGOR_QVGA=y
+# CONFIG_SH_MIGOR_RTA_WVGA is not set
#
# Timer and clock configuration
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
CONFIG_SMC91X=y
+# CONFIG_SMC911X is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
#
# I2C Hardware Bus support
#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
+CONFIG_I2C_SH_MOBILE=y
# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
# CONFIG_I2C_PCA_PLATFORM is not set
-CONFIG_I2C_SH_MOBILE=y
+# CONFIG_I2C_STUB is not set
#
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
+# CONFIG_AT24 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_USB_GADGET_ATMEL_USBA is not set
# CONFIG_USB_GADGET_FSL_USB2 is not set
# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA2XX is not set
+# CONFIG_USB_GADGET_PXA25X is not set
CONFIG_USB_GADGET_M66592=y
CONFIG_USB_M66592=y
CONFIG_SUPERH_BUILT_IN_M66592=y
CONFIG_USB_G_SERIAL=y
# CONFIG_USB_MIDI_GADGET is not set
# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
#
# SPI RTC drivers
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.25-rc4
-# Thu Mar 6 15:39:59 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:51:13 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=m
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
CONFIG_CLASSIC_RCU=y
-# CONFIG_PREEMPT_RCU is not set
#
# System type
# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_HUGETLB_PAGE_SIZE_64K=y
# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_RCU_TRACE=y
+# CONFIG_PREEMPT_RCU is not set
CONFIG_GUSA=y
#
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
+CONFIG_STP=m
CONFIG_BRIDGE=m
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
CONFIG_EEPROM_93CX6=y
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
CONFIG_SATA_SIL=y
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_PATA_PLATFORM=y
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
-# CONFIG_PCNET32_NAPI is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_TLAN is not set
CONFIG_VIA_RHINE=m
CONFIG_VIA_RHINE_MMIO=y
-# CONFIG_VIA_RHINE_NAPI is not set
# CONFIG_SC92031 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=m
-# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_E1000E is not set
-# CONFIG_E1000E_ENABLED is not set
# CONFIG_IP1000 is not set
# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=y
-# CONFIG_R8169_NAPI is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SH_KEYSC is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# Character devices
#
# CONFIG_VT is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL=y
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
CONFIG_DAB=y
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
# CONFIG_SND is not set
-
-#
-# Open Sound System
-#
CONFIG_SOUND_PRIME=m
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
-CONFIG_NFSD_TCP=y
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
-# CONFIG_CRYPTO_SEQIV is not set
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=m
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CTR is not set
-# CONFIG_CRYPTO_GCM is not set
-# CONFIG_CRYPTO_CCM is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc3
-# Fri Nov 23 14:03:57 2007
+# Linux kernel version: 2.6.26
+# Wed Jul 30 00:59:19 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
+CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-# CONFIG_SYSFS_DEPRECATED is not set
+# CONFIG_GROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
# CONFIG_FUTEX is not set
CONFIG_ANON_INODES=y
# CONFIG_EPOLL is not set
CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+CONFIG_PROFILING=y
+# CONFIG_MARKERS is not set
+CONFIG_OPROFILE=m
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_CLASSIC_RCU=y
#
# System type
CONFIG_CPU_SH4A=y
CONFIG_CPU_SHX2=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_CPU_SUBTYPE_SH7785=y
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
# CONFIG_CPU_SUBTYPE_SH5_101 is not set
# CONFIG_CPU_SUBTYPE_SH5_103 is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_HUGETLB_PAGE_SIZE_64K is not set
# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
CONFIG_HUGETLB_PAGE_SIZE_1MB=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
# CONFIG_MEMORY_HOTPLUG is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# Board support
#
CONFIG_SH_HIGHLANDER=y
+# CONFIG_SH_SH7785LCR is not set
# CONFIG_SH_R7780RP is not set
# CONFIG_SH_R7780MP is not set
CONFIG_SH_R7785RP=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_PREEMPT_BKL=y
+# CONFIG_PREEMPT_RCU is not set
CONFIG_GUSA=y
#
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
+CONFIG_STP=m
CONFIG_BRIDGE=m
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
CONFIG_EEPROM_93CX6=y
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
CONFIG_SATA_SIL=y
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_PATA_PLATFORM=y
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
-# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=y
-# CONFIG_R8169_NAPI is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SH_KEYSC is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# Character devices
#
# CONFIG_VT is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
# CONFIG_DAB is not set
#
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_SH_MOBILE_LCDC=m
# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_LOGO is not set
-
-#
-# Sound
-#
CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
# CONFIG_SND is not set
-
-#
-# Open Sound System
-#
CONFIG_SOUND_PRIME=m
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-
-#
-# USB Gadget Support
-#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
#
# Platform RTC drivers
#
+# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_V3020 is not set
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-CONFIG_MINIX_FS=y
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
-CONFIG_NFSD_TCP=y
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
# CONFIG_DLM is not set
-CONFIG_INSTRUMENTATION=y
-CONFIG_PROFILING=y
-CONFIG_OPROFILE=m
-# CONFIG_MARKERS is not set
#
# Kernel hacking
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SAMPLES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=m
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Tue Jun 3 13:02:42 2008
+# Linux kernel version: 2.6.26
+# Mon Jul 28 22:23:03 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
-# CONFIG_BSD_PROCESS_ACCT is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
+CONFIG_IKCONFIG=y
+# CONFIG_IKCONFIG_PROC is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
-# CONFIG_NAMESPACES is not set
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+CONFIG_USER_NS=y
+CONFIG_PID_NS=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
+# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
+CONFIG_SLOB=y
CONFIG_PROFILING=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
-CONFIG_SLABINFO=y
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
#
# Board support
#
+CONFIG_SH_RSK7203=y
#
# Timer and clock configuration
#
# Executable file formats
#
+CONFIG_BINFMT_ELF_FDPIC=y
CONFIG_BINFMT_FLAT=y
CONFIG_BINFMT_ZFLAT=y
CONFIG_BINFMT_SHARED_FLAT=y
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0x20000000
-CONFIG_MTD_PHYSMAP_LEN=0x01000000
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=4
# CONFIG_MTD_UCLINUX is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
CONFIG_MII=y
# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
-CONFIG_SMC91X=y
+# CONFIG_SMC91X is not set
+CONFIG_SMC911X=y
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_B44 is not set
-CONFIG_NETDEV_1000=y
-# CONFIG_E1000E_ENABLED is not set
-CONFIG_NETDEV_10000=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
#
# Wireless LAN
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# Multimedia drivers
#
CONFIG_DAB=y
+# CONFIG_USB_DABUSB is not set
#
# Graphics support
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
+# CONFIG_HID_FF is not set
+# CONFIG_USB_HIDDEV is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_ARCH_HAS_EHCI is not set
-# CONFIG_USB is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+CONFIG_USB_R8A66597_HCD=y
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
+
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SHIRQ=y
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_OBJECTS is not set
-# CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_OBJECTS=y
+# CONFIG_DEBUG_OBJECTS_SELFTEST is not set
+# CONFIG_DEBUG_OBJECTS_FREE is not set
+# CONFIG_DEBUG_OBJECTS_TIMERS is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_WRITECOUNT is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
+CONFIG_DEBUG_VM=y
+CONFIG_DEBUG_WRITECOUNT=y
+# CONFIG_DEBUG_MEMORY_INIT is not set
+CONFIG_DEBUG_LIST=y
+CONFIG_DEBUG_SG=y
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SAMPLES is not set
# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24
-# Thu Feb 7 16:25:55 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:55:52 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
+CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
# CONFIG_MODULE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
CONFIG_CLASSIC_RCU=y
-# CONFIG_PREEMPT_RCU is not set
#
# System type
# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
CONFIG_CPU_SUBTYPE_SH7751R=y
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
# CONFIG_CPU_SUBTYPE_SH5_101 is not set
# CONFIG_CPU_SUBTYPE_SH5_103 is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
-CONFIG_RCU_TRACE=y
CONFIG_GUSA=y
# CONFIG_GUSA_RB is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_PATA_PLATFORM=y
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
# CONFIG_ENC28J60 is not set
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
-# CONFIG_E1000E_ENABLED is not set
# CONFIG_IP1000 is not set
# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
CONFIG_MFD_SM501=y
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
CONFIG_DAB=y
# CONFIG_USB_DABUSB is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_SH_MOBILE_LCDC=m
CONFIG_FB_SM501=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
# CONFIG_LOGO_SUPERH_MONO is not set
# CONFIG_LOGO_SUPERH_VGA16 is not set
CONFIG_LOGO_SUPERH_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=y
-
-#
-# Advanced Linux Sound Architecture
-#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
+CONFIG_SND_VMASTER=y
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
-
-#
-# PCI devices
-#
+# CONFIG_SND_AC97_POWER_SAVE is not set
+CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
CONFIG_SND_YMFPCI=m
-CONFIG_SND_YMFPCI_FIRMWARE_IN_KERNEL=y
-# CONFIG_SND_AC97_POWER_SAVE is not set
-
-#
-# SPI devices
-#
-
-#
-# SUPERH devices
-#
-
-#
-# USB devices
-#
+CONFIG_SND_SPI=y
+CONFIG_SND_SUPERH=y
+CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not set
-
-#
-# System on Chip audio support
-#
# CONFIG_SND_SOC is not set
-
-#
-# SoC Audio support for SuperH
-#
-
-#
-# ALSA SoC audio for Freescale SOCs
-#
-
-#
-# Open Sound System
-#
CONFIG_SOUND_PRIME=m
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_EHCI_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
CONFIG_USB_LIBUSUAL=y
#
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
CONFIG_RTC_DRV_R9701=y
# CONFIG_RTC_DRV_RS5C348 is not set
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_SH is not set
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-CONFIG_MINIX_FS=y
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
-# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Crypto core or helper
+#
# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-# CONFIG_CRYPTO_CBC is not set
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CTR is not set
-# CONFIG_CRYPTO_GCM is not set
-# CONFIG_CRYPTO_CCM is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-# CONFIG_CRYPTO_DES is not set
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24
-# Thu Feb 7 16:17:47 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 01:59:18 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
+CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
# CONFIG_MODULE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
CONFIG_CLASSIC_RCU=y
-# CONFIG_PREEMPT_RCU is not set
#
# System type
# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
CONFIG_CPU_SUBTYPE_SH7751R=y
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
# CONFIG_CPU_SUBTYPE_SH5_101 is not set
# CONFIG_CPU_SUBTYPE_SH5_103 is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
-CONFIG_RCU_TRACE=y
CONFIG_GUSA=y
# CONFIG_GUSA_RB is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
#
# CONFIG_CFG80211 is not set
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
CONFIG_PATA_PLATFORM=y
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
# CONFIG_ENC28J60 is not set
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
-# CONFIG_E1000E_ENABLED is not set
# CONFIG_IP1000 is not set
# CONFIG_IGB is not set
# CONFIG_NS83820 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
CONFIG_MFD_SM501=y
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
CONFIG_DAB=y
# CONFIG_USB_DABUSB is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_SH_MOBILE_LCDC=m
CONFIG_FB_SM501=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
# CONFIG_LOGO_SUPERH_MONO is not set
# CONFIG_LOGO_SUPERH_VGA16 is not set
CONFIG_LOGO_SUPERH_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=y
-
-#
-# Advanced Linux Sound Architecture
-#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
+CONFIG_SND_VMASTER=y
CONFIG_SND_MPU401_UART=m
CONFIG_SND_OPL3_LIB=m
CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
-
-#
-# PCI devices
-#
+# CONFIG_SND_AC97_POWER_SAVE is not set
+CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
CONFIG_SND_YMFPCI=m
-CONFIG_SND_YMFPCI_FIRMWARE_IN_KERNEL=y
-# CONFIG_SND_AC97_POWER_SAVE is not set
-
-#
-# SPI devices
-#
-
-#
-# SUPERH devices
-#
-
-#
-# USB devices
-#
+CONFIG_SND_SPI=y
+CONFIG_SND_SUPERH=y
+CONFIG_SND_USB=y
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_CAIAQ is not set
-
-#
-# System on Chip audio support
-#
# CONFIG_SND_SOC is not set
-
-#
-# SoC Audio support for SuperH
-#
-
-#
-# ALSA SoC audio for Freescale SOCs
-#
-
-#
-# Open Sound System
-#
CONFIG_SOUND_PRIME=m
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
# CONFIG_USB_EHCI_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
CONFIG_USB_LIBUSUAL=y
#
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
CONFIG_RTC_DRV_R9701=y
# CONFIG_RTC_DRV_RS5C348 is not set
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_SH is not set
-
-#
-# Userspace I/O
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-CONFIG_MINIX_FS=y
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
-# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Crypto core or helper
+#
# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-# CONFIG_CRYPTO_CBC is not set
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CTR is not set
-# CONFIG_CRYPTO_GCM is not set
-# CONFIG_CRYPTO_CCM is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-# CONFIG_CRYPTO_DES is not set
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc7
-# Tue Jan 22 11:34:03 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 02:00:12 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=18
# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
+# CONFIG_GROUP_SCHED is not set
CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_RELAY=y
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
# CONFIG_CPU_SUBTYPE_SH5_101 is not set
# CONFIG_CPU_SUBTYPE_SH5_103 is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_HUGETLB_PAGE_SIZE_64K=y
# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=0
# CONFIG_SH_7780_SOLUTION_ENGINE is not set
CONFIG_SH_SDK7780=y
# CONFIG_SH_HIGHLANDER is not set
-# CONFIG_SH_SDK7780_STANDALONE is not set
CONFIG_SH_SDK7780_BASE=y
#
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_PREEMPT_BKL=y
+# CONFIG_PREEMPT_RCU is not set
CONFIG_GUSA=y
#
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_INET6_XFRM_MODE_BEET is not set
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=y
+CONFIG_IPV6_NDISC_NODETYPE=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
+# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_NET_SCH_HTB is not set
# CONFIG_NET_SCH_HFSC is not set
# CONFIG_NET_SCH_PRIO is not set
-# CONFIG_NET_SCH_RR is not set
# CONFIG_NET_SCH_RED is not set
# CONFIG_NET_SCH_SFQ is not set
# CONFIG_NET_SCH_TEQL is not set
# CONFIG_NET_SCH_GRED is not set
# CONFIG_NET_SCH_DSMARK is not set
# CONFIG_NET_SCH_NETEM is not set
-# CONFIG_NET_SCH_INGRESS is not set
#
# Classification
# CONFIG_NET_CLS_U32 is not set
# CONFIG_NET_CLS_RSVP is not set
# CONFIG_NET_CLS_RSVP6 is not set
+# CONFIG_NET_CLS_FLOW is not set
# CONFIG_NET_EMATCH is not set
# CONFIG_NET_CLS_ACT is not set
-# CONFIG_NET_CLS_POLICE is not set
CONFIG_NET_SCH_FIFO=y
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
CONFIG_IDE=y
CONFIG_IDE_MAX_HWIFS=4
CONFIG_BLK_DEV_IDE=y
#
-# Please see Documentation/ide.txt for help/info on IDE drives
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_BLK_DEV_IDECS is not set
# CONFIG_BLK_DEV_DELKIN is not set
CONFIG_BLK_DEV_IDECD=y
+CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
#
# IDE chipset support/bugfixes
#
-CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_PLATFORM=y
#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
-# CONFIG_IDEPCI_SHARE_IRQ is not set
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
-# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
-# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
-# CONFIG_IDE_ARM is not set
# CONFIG_BLK_DEV_IDEDMA is not set
-# CONFIG_IDE_ARCH_OBSOLETE_INIT is not set
-# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
+# CONFIG_PATA_SCH is not set
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
#
# IEEE 1394 (FireWire) support
#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
CONFIG_SMC91X=y
+# CONFIG_SMC911X is not set
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SH_KEYSC is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
# CONFIG_SYNCLINK_CS is not set
# CONFIG_CARDMAN_4000 is not set
# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=y
+CONFIG_SSB_SPROM=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
+# CONFIG_SSB_B43_PCI_BRIDGE is not set
CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
# CONFIG_SSB_PCMCIAHOST is not set
# CONFIG_SSB_SILENT is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
# CONFIG_DAB is not set
#
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_SH_MOBILE_LCDC=m
# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
CONFIG_LOGO_SUPERH_MONO=y
CONFIG_LOGO_SUPERH_VGA16=y
CONFIG_LOGO_SUPERH_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=y
-
-#
-# Advanced Linux Sound Architecture
-#
# CONFIG_SND is not set
-
-#
-# Open Sound System
-#
CONFIG_SOUND_PRIME=y
-# CONFIG_SOUND_TRIDENT is not set
-# CONFIG_SOUND_MSNDCLAS is not set
-# CONFIG_SOUND_MSNDPIN is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=y
-# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_EHCI_TT_NEWSCHED is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
#
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
+# CONFIG_USB_WDM is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
-
-#
-# USB Serial Converter support
-#
# CONFIG_USB_SERIAL is not set
#
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
-
-#
-# USB DSL modem support
-#
-
-#
-# USB Gadget Support
-#
+# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
-
-#
-# Userspace I/O
-#
# CONFIG_UIO is not set
#
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-CONFIG_MINIX_FS=y
-# CONFIG_ROMFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+CONFIG_MINIX_FS=y
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-CONFIG_NFSD_TCP=y
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
#
# Kernel hacking
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_DEBUG_FS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
CONFIG_TIMER_STATS=y
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_FRAME_POINTER is not set
-# CONFIG_FORCED_INLINING is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SAMPLES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
CONFIG_CRYPTO_ALGAPI=y
# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-# CONFIG_CRYPTO_CBC is not set
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_LZO is not set
CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+CONFIG_CRC_T10DIF=y
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc4
-# Tue Jun 3 20:27:08 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 02:06:07 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_RT_MUTEXES=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
#
# Executable file formats
#
+CONFIG_BINFMT_ELF_FDPIC=y
CONFIG_BINFMT_FLAT=y
CONFIG_BINFMT_ZFLAT=y
CONFIG_BINFMT_SHARED_FLAT=y
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
CONFIG_EEPROM_93CX6=y
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
CONFIG_SMC91X=y
+# CONFIG_SMC911X is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_SH=y
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_VM=y
# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
CONFIG_DEBUG_LIST=y
# CONFIG_DEBUG_SG is not set
CONFIG_FRAME_POINTER=y
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_GENERIC_FIND_FIRST_BIT is not set
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
+# CONFIG_CRC_T10DIF is not set
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
CONFIG_CRC7=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.26-rc8
-# Mon Jul 7 13:12:45 2008
+# Linux kernel version: 2.6.26
+# Wed Jul 30 02:08:38 2008
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
# CONFIG_PROFILING is not set
# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
# CONFIG_HAVE_KPROBES is not set
# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SLABINFO=y
CONFIG_TINY_SHMEM=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_PAGE_SIZE_8KB is not set
# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_AX88796 is not set
# CONFIG_STNIC is not set
CONFIG_SMC91X=y
+# CONFIG_SMC911X is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_B44 is not set
CONFIG_NETDEV_1000=y
-# CONFIG_E1000E_ENABLED is not set
CONFIG_NETDEV_10000=y
#
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_SOC_CAMERA is not set
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
CONFIG_RADIO_ADAPTERS=y
# CONFIG_DAB is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+CONFIG_FB_CFB_FILLRECT=m
+CONFIG_FB_CFB_COPYAREA=m
+CONFIG_FB_CFB_IMAGEBLIT=m
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# Frame buffer hardware drivers
#
# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_SH_MOBILE_LCDC=m
# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set
# CONFIG_LOGO is not set
-
-#
-# Sound
-#
CONFIG_SOUND=y
-
-#
-# Advanced Linux Sound Architecture
-#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
+CONFIG_SND_DRIVERS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
-
-#
-# SUPERH devices
-#
-
-#
-# System on Chip audio support
-#
+CONFIG_SND_SUPERH=y
# CONFIG_SND_SOC is not set
-
-#
-# SoC Audio support for SuperH
-#
-
-#
-# ALSA SoC audio for Freescale SOCs
-#
-
-#
-# SoC Audio for the Texas Instruments OMAP
-#
-
-#
-# Open Sound System
-#
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
#
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.22-rc4
-# Fri Jun 15 19:43:06 2007
+# Linux kernel version: 2.6.26
+# Wed Jul 30 02:12:32 2008
#
CONFIG_SUPERH=y
+CONFIG_SUPERH32=y
+CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_LOCKDEP_SUPPORT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_NO_VIRT_TO_BUS=y
+CONFIG_ARCH_SUPPORTS_AOUT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
-# Code maturity level options
+# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_UTS_NS is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
# CONFIG_ELF_CORE is not set
+CONFIG_COMPAT_BRK=y
# CONFIG_BASE_FULL is not set
# CONFIG_FUTEX is not set
CONFIG_ANON_INODES=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_ARCH_TRACEHOOK is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+CONFIG_HAVE_CLK=y
+CONFIG_SLABINFO=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=1
-
-#
-# Loadable module support
-#
# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_CLASSIC_RCU=y
#
# System type
#
CONFIG_CPU_SH2=y
CONFIG_CPU_SUBTYPE_SH7619=y
+# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
-# CONFIG_CPU_SUBTYPE_SH7300 is not set
+# CONFIG_CPU_SUBTYPE_SH7263 is not set
+# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
+# CONFIG_CPU_SUBTYPE_SH7720 is not set
+# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
-# CONFIG_CPU_SUBTYPE_ST40STB1 is not set
-# CONFIG_CPU_SUBTYPE_ST40GX1 is not set
+# CONFIG_CPU_SUBTYPE_SH7723 is not set
+# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
-# CONFIG_CPU_SUBTYPE_SH73180 is not set
+# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
+# CONFIG_CPU_SUBTYPE_SH7366 is not set
+# CONFIG_CPU_SUBTYPE_SH5_101 is not set
+# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
CONFIG_PAGE_OFFSET=0x00000000
CONFIG_MEMORY_START=0x0c000000
CONFIG_MEMORY_SIZE=0x04000000
+CONFIG_29BIT=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
-CONFIG_SH_WRITETHROUGH=y
+# CONFIG_CACHE_WRITEBACK is not set
+CONFIG_CACHE_WRITETHROUGH=y
+# CONFIG_CACHE_OFF is not set
#
# Processor features
# CONFIG_CPU_LITTLE_ENDIAN is not set
CONFIG_CPU_BIG_ENDIAN=y
# CONFIG_SH_FPU_EMU is not set
-# CONFIG_SH_DSP is not set
-CONFIG_CPU_HAS_IPR_IRQ=y
#
# Board support
#
# DMA support
#
-# CONFIG_SH_DMA is not set
#
# Companion Chips
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=100
+# CONFIG_SCHED_HRTICK is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
+CONFIG_GUSA=y
#
# Boot options
#
# Bus options
#
+# CONFIG_CF_ENABLER is not set
# CONFIG_ARCH_SUPPORTS_MSI is not set
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-
#
# Executable file formats
#
+CONFIG_BINFMT_ELF_FDPIC=y
CONFIG_BINFMT_FLAT=y
CONFIG_BINFMT_ZFLAT=y
# CONFIG_BINFMT_SHARED_FLAT is not set
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=y
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
-
-#
-# Parallel port support
-#
# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
+CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
-
-#
-# Misc devices
-#
-# CONFIG_BLINK is not set
+# CONFIG_BLK_DEV_HD is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
# CONFIG_MD is not set
-
-#
-# ISDN subsystem
-#
-
-#
-# Telephony Support
-#
# CONFIG_PHONE is not set
#
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
# Character devices
#
# CONFIG_VT is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_UNIX98_PTYS is not set
# CONFIG_LEGACY_PTYS is not set
-
-#
-# IPMI
-#
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
#
-# Dallas's 1-wire bus
+# Sonics Silicon Backplane
#
-# CONFIG_W1 is not set
-# CONFIG_HWMON is not set
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
-CONFIG_DAB=y
+# CONFIG_VIDEO_MEDIA is not set
#
-# Graphics support
+# Multimedia drivers
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_DAB=y
#
-# Display device support
+# Graphics support
#
-# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
-# Sound
+# Display device support
#
+# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
+CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
-
-#
-# USB Gadget Support
-#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
-
-#
-# LED devices
-#
+# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
#
# File systems
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-CONFIG_ROMFS_FS=y
+# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_SYSFS is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
#
# Miscellaneous filesystems
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
# CONFIG_NLS is not set
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_SAMPLES is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
# Security options
#
# CONFIG_KEYS is not set
-
-#
-# Cryptographic options
-#
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_HAS_IOMEM=y
#include <linux/module.h>
#include <linux/interrupt.h>
#include <asm/cacheflush.h>
-#include <asm/mach/sysasic.h>
-#include <asm/mach/dma.h>
+#include <mach/sysasic.h>
+#include <mach/dma.h>
#include <asm/dma.h>
struct g2_channel {
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
-#include <asm/mach/sysasic.h>
-#include <asm/mach/dma.h>
+#include <mach/sysasic.h>
+#include <mach/dma.h>
#include <asm/dma.h>
#include <asm/io.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/module.h>
-#include <asm/dreamcast/dma.h>
+#include <mach-dreamcast/mach/dma.h>
#include <asm/dma.h>
#include <asm/io.h>
#include "dma-sh.h"
#ifndef __DMA_SH_H
#define __DMA_SH_H
-#include <asm/cpu/dma.h>
+#include <cpu/dma.h>
/* Definitions for the SuperH DMAC */
#define REQ_L 0x00000000
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/mach/pci.h>
+#include <mach/pci.h>
static void __init gapspci_fixup_resources(struct pci_dev *dev)
{
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/types.h>
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
#include "pci-sh5.h"
static inline u8 bridge_swizzle(u8 pin, u8 slot)
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/mach/pci.h>
+#include <mach/pci.h>
static struct resource gapspci_io_resource = {
.name = "GAPSPCI IO",
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pci.h>
-#include <asm/se7780.h>
+#include <mach-se/mach/se7780.h>
#include <asm/io.h>
#include "pci-sh4.h"
#include <linux/delay.h>
#include <linux/types.h>
#include <linux/irq.h>
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
#include <asm/pci.h>
#include <asm/io.h>
#include "pci-sh5.h"
* Copyright (C) 2004 Andriy Skulysh
*/
-#include <asm/cpu/adc.h>
+#include <cpu/adc.h>
int adc_single(unsigned int channel);
#ifdef __KERNEL__
-#include <asm/cpu/addrspace.h>
+#include <cpu/addrspace.h>
/* If this CPU supports segmentation, hook up the helpers */
#ifdef P1SEG
*/
#define AT_FPUCW 18 /* Used FPU control word. */
-#ifdef CONFIG_VSYSCALL
+#if defined(CONFIG_VSYSCALL) || !defined(__KERNEL__)
/*
* Only define this in the vsyscall case, the entry point to
* the vsyscall page gets placed here. The kernel will attempt
#ifdef __KERNEL__
#include <linux/init.h>
-#include <asm/cpu/cache.h>
+#include <cpu/cache.h>
#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT)
#define __flush_purge_region(start, size) do { (void)(start); } while (0)
#define __flush_invalidate_region(start, size) do { (void)(start); } while (0)
#else
-#include <asm/cpu/cacheflush.h>
+#include <cpu/cacheflush.h>
/*
* Consistent DMA requires that the __flush_xxx() primitives must be set
#include <linux/wait.h>
#include <linux/sched.h>
#include <linux/sysdev.h>
-#include <asm/cpu/dma.h>
+#include <cpu/dma.h>
/* The maximum address that we can perform a DMA transfer to on this platform */
/* Don't define MAX_DMA_ADDRESS; it's useless on the SuperH and any
#define __ASM_SH_FREQ_H
#ifdef __KERNEL__
-#include <asm/cpu/freq.h>
+#include <cpu/freq.h>
#endif /* __KERNEL__ */
#endif /* __ASM_SH_FREQ_H */
#define __ASM_SH_GPIO_H
#if defined(CONFIG_CPU_SH3)
-#include <asm/cpu/gpio.h>
+#include <cpu/gpio.h>
#endif
#endif /* __ASM_SH_GPIO_H */
#endif
#ifdef CONFIG_CPU_SH5
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
#endif
#endif /* __ASM_SH_IRQ_H */
#ifndef __ASM_SH_IRQFLAGS_64_H
#define __ASM_SH_IRQFLAGS_64_H
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
#define SR_MASK_LL 0x00000000000000f0LL
#define SR_BL_LL 0x0000000010000000LL
#define __ASM_SH_MMU_CONTEXT_H
#ifdef __KERNEL__
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
#include <asm/tlbflush.h>
#include <asm/uaccess.h>
#include <asm/io.h>
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
#include <asm/cacheflush.h>
#define SR_ASID_MASK 0xffffffffff00ffffULL
* Default implementation of macro that returns current
* instruction pointer ("program counter").
*/
-#define current_text_addr() ({ void *pc; __asm__("mova 1f, %0\n1:":"=z" (pc)); pc; })
+#define current_text_addr() ({ void *pc; __asm__("mova 1f, %0\n.align 2\n1:":"=z" (pc)); pc; })
/* Core Processor Version Register */
#define CCN_PVR 0xff000030
#include <asm/types.h>
#include <asm/cache.h>
#include <asm/ptrace.h>
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
/*
* Default implementation of macro that returns current
extern void show_regs(struct pt_regs *);
+/*
+ * These are defined as per linux/ptrace.h.
+ */
+struct task_struct;
+
+#define arch_has_single_step() (1)
+extern void user_enable_single_step(struct task_struct *);
+extern void user_disable_single_step(struct task_struct *);
+
#ifdef CONFIG_SH_DSP
#define task_pt_regs(task) \
((struct pt_regs *) (task_stack_page(task) + THREAD_SIZE \
unsigned long capabilities;
};
-#include <asm/cpu/rtc.h>
+#include <cpu/rtc.h>
#endif /* _ASM_RTC_H */
--- /dev/null
+#ifndef __ASM_SECCOMP_H
+
+#include <linux/unistd.h>
+
+#define __NR_seccomp_read __NR_read
+#define __NR_seccomp_write __NR_write
+#define __NR_seccomp_exit __NR_exit
+#define __NR_seccomp_sigreturn __NR_rt_sigreturn
+
+#endif /* __ASM_SECCOMP_H */
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
#ifdef CONFIG_HD64465
-#include <asm/hd64465.h>
+#include <asm/hd64465/hd64465.h>
#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
--- /dev/null
+#ifndef __ASM_SH_ETH_H__
+#define __ASM_SH_ETH_H__
+
+enum {EDMAC_LITTLE_ENDIAN, EDMAC_BIG_ENDIAN};
+
+struct sh_eth_plat_data {
+ int phy;
+ int edmac_endian;
+};
+
+#endif
#define TIF_NEED_RESCHED 2 /* rescheduling necessary */
#define TIF_RESTORE_SIGMASK 3 /* restore signal mask in do_signal() */
#define TIF_SINGLESTEP 4 /* singlestepping active */
-#define TIF_SYSCALL_AUDIT 5
+#define TIF_SYSCALL_AUDIT 5 /* syscall auditing active */
+#define TIF_SECCOMP 6 /* secure computing */
+#define TIF_NOTIFY_RESUME 7 /* callback before returning to user */
#define TIF_USEDFPU 16 /* FPU was used by this task this quantum (SMP) */
#define TIF_POLLING_NRFLAG 17 /* true if poll_idle() is polling TIF_NEED_RESCHED */
#define TIF_MEMDIE 18
-#define TIF_FREEZE 19
-
-#define _TIF_SYSCALL_TRACE (1<<TIF_SYSCALL_TRACE)
-#define _TIF_SIGPENDING (1<<TIF_SIGPENDING)
-#define _TIF_NEED_RESCHED (1<<TIF_NEED_RESCHED)
-#define _TIF_RESTORE_SIGMASK (1<<TIF_RESTORE_SIGMASK)
-#define _TIF_SINGLESTEP (1<<TIF_SINGLESTEP)
-#define _TIF_SYSCALL_AUDIT (1<<TIF_SYSCALL_AUDIT)
-#define _TIF_USEDFPU (1<<TIF_USEDFPU)
-#define _TIF_POLLING_NRFLAG (1<<TIF_POLLING_NRFLAG)
-#define _TIF_FREEZE (1<<TIF_FREEZE)
-
-#define _TIF_WORK_MASK 0x000000FE /* work to do on interrupt/exception return */
-#define _TIF_ALLWORK_MASK 0x000000FF /* work to do on any return to u-space */
+#define TIF_FREEZE 19 /* Freezing for suspend */
+
+#define _TIF_SYSCALL_TRACE (1 << TIF_SYSCALL_TRACE)
+#define _TIF_SIGPENDING (1 << TIF_SIGPENDING)
+#define _TIF_NEED_RESCHED (1 << TIF_NEED_RESCHED)
+#define _TIF_RESTORE_SIGMASK (1 << TIF_RESTORE_SIGMASK)
+#define _TIF_SINGLESTEP (1 << TIF_SINGLESTEP)
+#define _TIF_SYSCALL_AUDIT (1 << TIF_SYSCALL_AUDIT)
+#define _TIF_SECCOMP (1 << TIF_SECCOMP)
+#define _TIF_NOTIFY_RESUME (1 << TIF_NOTIFY_RESUME)
+#define _TIF_USEDFPU (1 << TIF_USEDFPU)
+#define _TIF_POLLING_NRFLAG (1 << TIF_POLLING_NRFLAG)
+#define _TIF_FREEZE (1 << TIF_FREEZE)
+
+/*
+ * _TIF_ALLWORK_MASK and _TIF_WORK_MASK need to fit within a byte, or we
+ * blow the tst immediate size constraints and need to fix up
+ * arch/sh/kernel/entry-common.S.
+ */
+
+/* work to do in syscall trace */
+#define _TIF_WORK_SYSCALL_MASK (_TIF_SYSCALL_TRACE | _TIF_SINGLESTEP | \
+ _TIF_SYSCALL_AUDIT | _TIF_SECCOMP)
+
+/* work to do on any return to u-space */
+#define _TIF_ALLWORK_MASK (_TIF_SYSCALL_TRACE | _TIF_SIGPENDING | \
+ _TIF_NEED_RESCHED | _TIF_SYSCALL_AUDIT | \
+ _TIF_SINGLESTEP | _TIF_RESTORE_SIGMASK | \
+ _TIF_NOTIFY_RESUME)
+
+/* work to do on interrupt/exception return */
+#define _TIF_WORK_MASK (_TIF_ALLWORK_MASK & ~(_TIF_SYSCALL_TRACE | \
+ _TIF_SYSCALL_AUDIT | _TIF_SINGLESTEP))
#endif /* __KERNEL__ */
#include <linux/sysdev.h>
#include <linux/clocksource.h>
-#include <asm/cpu/timer.h>
+#include <cpu/timer.h>
struct sys_timer_ops {
int (*init)(void);
#ifndef __ASSEMBLY__
/**
- * for_each_dtlb_entry
+ * for_each_dtlb_entry - Iterate over free (non-wired) DTLB entries
*
* @tlb: TLB entry
- *
- * Iterate over free (non-wired) DTLB entries
*/
#define for_each_dtlb_entry(tlb) \
for (tlb = cpu_data->dtlb.first; \
tlb += cpu_data->dtlb.step)
/**
- * for_each_itlb_entry
+ * for_each_itlb_entry - Iterate over free (non-wired) ITLB entries
*
* @tlb: TLB entry
- *
- * Iterate over free (non-wired) ITLB entries
*/
#define for_each_itlb_entry(tlb) \
for (tlb = cpu_data->itlb.first; \
tlb += cpu_data->itlb.step)
/**
- * __flush_tlb_slot
+ * __flush_tlb_slot - Flushes TLB slot @slot.
*
* @slot: Address of TLB slot.
- *
- * Flushes TLB slot @slot.
*/
static inline void __flush_tlb_slot(unsigned long long slot)
{
({ \
long __pu_err; \
__typeof__(*(ptr)) __user *__pu_addr = (ptr); \
+ __typeof__(*(ptr)) __pu_val = x; \
__chk_user_ptr(ptr); \
- __put_user_size((x), __pu_addr, (size), __pu_err); \
+ __put_user_size(__pu_val, __pu_addr, (size), __pu_err); \
__pu_err; \
})
({ \
long __pu_err = -EFAULT; \
__typeof__(*(ptr)) __user *__pu_addr = (ptr); \
+ __typeof__(*(ptr)) __pu_val = x; \
if (likely(access_ok(VERIFY_WRITE, __pu_addr, size))) \
- __put_user_size((x), __pu_addr, (size), \
+ __put_user_size(__pu_val, __pu_addr, (size), \
__pu_err); \
__pu_err; \
})
__put_user_asm(x, ptr, retval, "w"); \
break; \
case 4: \
- __put_user_asm((u32)x, ptr, \
- retval, "l"); \
+ __put_user_asm(x, ptr, retval, "l"); \
break; \
case 8: \
__put_user_u64(x, ptr, retval); \
#define __ASM_SH_UBC_H
#ifdef __KERNEL__
-#include <asm/cpu/ubc.h>
+#include <cpu/ubc.h>
/* User Break Controller */
#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
#ifdef __KERNEL__
#include <linux/types.h>
-#include <asm/cpu/watchdog.h>
+#include <cpu/watchdog.h>
#include <asm/io.h>
/*
- * See asm/cpu-sh2/watchdog.h for explanation of this stupidity..
+ * See cpu-sh2/watchdog.h for explanation of this stupidity..
*/
#ifndef WTCNT_R
# define WTCNT_R WTCNT
#ifndef __ASM_CPU_SH2_CACHEFLUSH_H
#define __ASM_CPU_SH2_CACHEFLUSH_H
-/*
+/*
* Cache flushing:
*
* - flush_cache_all() flushes entire cache
#define flush_cache_sigtramp(vaddr) do { } while (0)
#define p3_cache_init() do { } while (0)
-#endif /* __ASM_CPU_SH2_CACHEFLUSH_H */
+#endif /* __ASM_CPU_SH2_CACHEFLUSH_H */
#define CCR 0xffffffec
#define CCR_CACHE_CE 0x01 /* Cache enable */
-#define CCR_CACHE_WT 0x06 /* CCR[bit1=1,bit2=1] */
+#define CCR_CACHE_WT 0x02 /* CCR[bit1=1,bit2=1] */
/* 0x00000000-0x7fffffff: Write-through */
/* 0x80000000-0x9fffffff: Write-back */
/* 0xc0000000-0xdfffffff: Write-through */
-#define CCR_CACHE_CB 0x00 /* CCR[bit1=0,bit2=0] */
+#define CCR_CACHE_CB 0x04 /* CCR[bit1=0,bit2=0] */
/* 0x00000000-0x7fffffff: Write-back */
/* 0x80000000-0x9fffffff: Write-through */
/* 0xc0000000-0xdfffffff: Write-back */
#define CCR_CACHE_ENABLE CCR_CACHE_CE
#define CCR_CACHE_INVALIDATE CCR_CACHE_CF
+#define CACHE_PHYSADDR_MASK 0x1ffffc00
+
#endif
#endif /* __ASM_CPU_SH2_CACHE_H */
#define P0SEG 0x00000000
#define P1SEG 0x00000000
#define P2SEG 0x20000000
-#define P3SEG 0x00000000
-#define P4SEG 0x80000000
+#define P3SEG 0x40000000
+#define P4SEG 0x60000000
#endif /* __ASM_SH_CPU_SH2A_ADDRSPACE_H */
#define CCR_CACHE_ENABLE (CCR_CACHE_OCE | CCR_CACHE_ICE)
#define CCR_CACHE_INVALIDATE (CCR_CACHE_OCI | CCR_CACHE_ICI)
+#define CCR_ICACHE_INVALIDATE CCR_CACHE_ICI
+#define CCR_OCACHE_INVALIDATE CCR_CACHE_OCI
+#define CACHE_PHYSADDR_MASK 0x1ffffc00
#endif /* __ASM_CPU_SH2A_CACHE_H */
--- /dev/null
+#ifndef __ASM_CPU_SH2A_CACHEFLUSH_H
+#define __ASM_CPU_SH2A_CACHEFLUSH_H
+
+/*
+ * Cache flushing:
+ *
+ * - flush_cache_all() flushes entire cache
+ * - flush_cache_mm(mm) flushes the specified mm context's cache lines
+ * - flush_cache_dup mm(mm) handles cache flushing when forking
+ * - flush_cache_page(mm, vmaddr, pfn) flushes a single page
+ * - flush_cache_range(vma, start, end) flushes a range of pages
+ *
+ * - flush_dcache_page(pg) flushes(wback&invalidates) a page for dcache
+ * - flush_icache_range(start, end) flushes(invalidates) a range for icache
+ * - flush_icache_page(vma, pg) flushes(invalidates) a page for icache
+ *
+ * Caches are indexed (effectively) by physical address on SH-2, so
+ * we don't need them.
+ */
+#define flush_cache_all() do { } while (0)
+#define flush_cache_mm(mm) do { } while (0)
+#define flush_cache_dup_mm(mm) do { } while (0)
+#define flush_cache_range(vma, start, end) do { } while (0)
+#define flush_cache_page(vma, vmaddr, pfn) do { } while (0)
+#define flush_dcache_page(page) do { } while (0)
+#define flush_dcache_mmap_lock(mapping) do { } while (0)
+#define flush_dcache_mmap_unlock(mapping) do { } while (0)
+void flush_icache_range(unsigned long start, unsigned long end);
+#define flush_icache_page(vma,pg) do { } while (0)
+#define flush_icache_user_range(vma,pg,adr,len) do { } while (0)
+#define flush_cache_sigtramp(vaddr) do { } while (0)
+
+#define p3_cache_init() do { } while (0)
+#endif /* __ASM_CPU_SH2A_CACHEFLUSH_H */
--- /dev/null
+#include <cpu-sh2/cpu/dma.h>
--- /dev/null
+#include <cpu-sh2/cpu/ubc.h>
--- /dev/null
+#include <cpu-sh2/cpu/watchdog.h>
--- /dev/null
+/*
+ * include/asm-sh/cpu-sh3/cacheflush.h
+ *
+ * Copyright (C) 1999 Niibe Yutaka
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_CPU_SH3_CACHEFLUSH_H
+#define __ASM_CPU_SH3_CACHEFLUSH_H
+
+#if defined(CONFIG_SH7705_CACHE_32KB)
+/* SH7705 is an SH3 processor with 32KB cache. This has alias issues like the
+ * SH4. Unlike the SH4 this is a unified cache so we need to do some work
+ * in mmap when 'exec'ing a new binary
+ */
+ /* 32KB cache, 4kb PAGE sizes need to check bit 12 */
+#define CACHE_ALIAS 0x00001000
+
+#define PG_mapped PG_arch_1
+
+void flush_cache_all(void);
+void flush_cache_mm(struct mm_struct *mm);
+#define flush_cache_dup_mm(mm) flush_cache_mm(mm)
+void flush_cache_range(struct vm_area_struct *vma, unsigned long start,
+ unsigned long end);
+void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned long pfn);
+void flush_dcache_page(struct page *pg);
+void flush_icache_range(unsigned long start, unsigned long end);
+void flush_icache_page(struct vm_area_struct *vma, struct page *page);
+#else
+#include <cpu-common/cpu/cacheflush.h>
+#endif
+
+#endif /* __ASM_CPU_SH3_CACHEFLUSH_H */
#define CHCR_TS_MASK 0x18
#define CHCR_TS_SHIFT 3
-#include <asm/cpu/dma-sh7780.h>
+#include <cpu/dma-sh7780.h>
#else
#define SH_DMAC_BASE 0xffa00000
#ifndef __ASM_SH_DREAMCAST_PCI_H
#define __ASM_SH_DREAMCAST_PCI_H
-#include <asm/mach/sysasic.h>
+#include <mach-dreamcast/mach/sysasic.h>
#define GAPSPCI_REGS 0x01001400
#define GAPSPCI_DMA_BASE 0x01840000
--- /dev/null
+vmlinux.lds
}
#if defined(CONFIG_SH_SOLUTION_ENGINE)
-#include <asm/se.h>
+#include <mach-se/mach/se.h>
#elif defined(CONFIG_SH_7722_SOLUTION_ENGINE)
-#include <asm/se7722.h>
+#include <mach-se/mach/se7722.h>
#elif defined(CONFIG_SH_7721_SOLUTION_ENGINE)
-#include <asm/se7721.h>
+#include <mach-se/mach/se7721.h>
#endif
/*
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/bitops.h>
-#include <asm/cpu/irq.h>
+#include <cpu/irq.h>
#include <asm/page.h>
/*
#include <linux/linkage.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
#include <asm/unistd.h>
#include <asm/errno.h>
#include <asm/page.h>
#include <linux/linkage.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
#include <asm/unistd.h>
#include <asm/errno.h>
#include <asm/page.h>
#include <asm/asm-offsets.h>
#include <asm/thread_info.h>
#include <asm/unistd.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
#include <asm/page.h>
! NOTE:
#include <linux/sched.h>
#include <linux/signal.h>
#include <linux/io.h>
-#include <asm/cpu/fpu.h>
+#include <cpu/fpu.h>
#include <asm/processor.h>
#include <asm/system.h>
#include <asm/fpu.h>
* and Kamel Khelifi <kamel.khelifi@st.com>
*/
#include <linux/kernel.h>
-#include <asm/cpu/fpu.h>
+#include <cpu/fpu.h>
#define LIT64( a ) a##LL
#include <linux/io.h>
#include <asm/page.h>
#include <asm/cacheflush.h>
-#include <asm/cpu/sq.h>
+#include <cpu/sq.h>
struct sq_mapping;
/**
* sq_unmap - Unmap a Store Queue allocation
- * @map: Pre-allocated Store Queue mapping.
+ * @vaddr: Pre-allocated Store Queue mapping.
*
* Unmaps the store queue allocation @map that was previously created by
* sq_remap(). Also frees up the pte that was previously inserted into
*/
#include <linux/errno.h>
#include <linux/sys.h>
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
#include <asm/processor.h>
#include <asm/unistd.h>
#include <asm/thread_info.h>
work_notifysig:
gettr tr1, LINK
- movi do_signal, r6
+ movi do_notify_resume, r6
ptabs r6, tr0
or SP, ZERO, r2
- or ZERO, ZERO, r3
- blink tr0, LINK /* Call do_signal(regs, 0), return here */
+ or r7, ZERO, r3
+ blink tr0, LINK /* Call do_notify_resume(regs, current_thread_info->flags), return here */
restore_all:
/* Do prefetches */
getcon KCR0, r2
ld.l r2, TI_FLAGS, r4
- movi (_TIF_SYSCALL_TRACE | _TIF_SINGLESTEP | _TIF_SYSCALL_AUDIT), r6
+ movi _TIF_WORK_SYSCALL_MASK, r6
and r6, r4, r6
beq/l r6, ZERO, tr0
/* Trace it by calling syscall_trace before and after */
- movi syscall_trace, r4
+ movi do_syscall_trace_enter, r4
or SP, ZERO, r2
- or ZERO, ZERO, r3
ptabs r4, tr0
blink tr0, LINK
- /* Reload syscall number as r5 is trashed by syscall_trace */
+ /* Save the retval */
+ st.q SP, FRAME_R(2), r2
+
+ /* Reload syscall number as r5 is trashed by do_syscall_trace_enter */
ld.q SP, FRAME_S(FSYSCALL_ID), r5
andi r5, 0x1ff, r5
/* We get back here only if under trace */
st.q SP, FRAME_R(9), r2 /* Save return value */
- movi syscall_trace, LINK
+ movi do_syscall_trace_leave, LINK
or SP, ZERO, r2
- movi 1, r3
ptabs LINK, tr0
blink tr0, LINK
syscall_exit_work:
! r0: current_thread_info->flags
! r8: current_thread_info
- tst #_TIF_SYSCALL_TRACE | _TIF_SINGLESTEP | _TIF_SYSCALL_AUDIT, r0
+ tst #_TIF_WORK_SYSCALL_MASK, r0
bt/s work_pending
tst #_TIF_NEED_RESCHED, r0
#ifdef CONFIG_TRACE_IRQFLAGS
nop
#endif
sti
- ! XXX setup arguments...
mov r15, r4
- mov #1, r5
- mov.l 4f, r0 ! do_syscall_trace
+ mov.l 8f, r0 ! do_syscall_trace_leave
jsr @r0
nop
bra resume_userspace
.align 2
syscall_trace_entry:
! Yes it is traced.
- ! XXX setup arguments...
mov r15, r4
- mov #0, r5
- mov.l 4f, r11 ! Call do_syscall_trace which notifies
+ mov.l 7f, r11 ! Call do_syscall_trace_enter which notifies
jsr @r11 ! superior (will chomp R[0-7])
nop
+ mov.l r0, @(OFF_R0,r15) ! Save return value
! Reload R0-R4 from kernel stack, where the
! parent may have modified them using
! ptrace(POKEUSR). (Note that R0-R2 are
!
get_current_thread_info r8, r10
mov.l @(TI_FLAGS,r8), r8
- mov #(_TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT), r10
+ mov #_TIF_WORK_SYSCALL_MASK, r10
tst r10, r8
bf syscall_trace_entry
!
#endif
2: .long NR_syscalls
3: .long sys_call_table
-4: .long do_syscall_trace
#ifdef CONFIG_TRACE_IRQFLAGS
5: .long trace_hardirqs_on
6: .long trace_hardirqs_off
#endif
+7: .long do_syscall_trace_enter
+8: .long do_syscall_trace_leave
#include <asm/page.h>
#include <asm/cache.h>
#include <asm/tlb.h>
-#include <asm/cpu/registers.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/registers.h>
+#include <cpu/mmu_context.h>
#include <asm/thread_info.h>
/*
#include <asm/machvec.h>
#include <asm/uaccess.h>
#include <asm/thread_info.h>
-#include <asm/cpu/mmu_context.h>
+#include <cpu/mmu_context.h>
atomic_t irq_err_count;
#include <linux/kexec.h>
#include <linux/delay.h>
#include <linux/reboot.h>
+#include <linux/numa.h>
#include <asm/pgtable.h>
#include <asm/pgalloc.h>
#include <asm/mmu_context.h>
(*rnk)(page_list, reboot_code_buffer, image->start, vbr_reg);
}
+void arch_crash_save_vmcoreinfo(void)
+{
+#ifdef CONFIG_NUMA
+ VMCOREINFO_SYMBOL(node_data);
+ VMCOREINFO_LENGTH(node_data, MAX_NUMNODES);
+#endif
+}
#include <linux/moduleloader.h>
#include <linux/elf.h>
#include <linux/vmalloc.h>
+#include <linux/bug.h>
#include <linux/fs.h>
#include <linux/string.h>
#include <linux/kernel.h>
{
if (size == 0)
return NULL;
- return vmalloc(size);
+
+ return vmalloc_exec(size);
}
const Elf_Shdr *sechdrs,
struct module *me)
{
- return 0;
+ return module_bug_finalize(hdr, sechdrs, me);
}
void module_arch_cleanup(struct module *mod)
{
+ module_bug_cleanup(mod);
}
#include <linux/signal.h>
#include <linux/io.h>
#include <linux/audit.h>
+#include <linux/seccomp.h>
+#include <linux/tracehook.h>
#include <asm/uaccess.h>
#include <asm/pgtable.h>
#include <asm/system.h>
return 0;
}
-static void ptrace_disable_singlestep(struct task_struct *child)
+void user_enable_single_step(struct task_struct *child)
+{
+ struct pt_regs *regs = task_pt_regs(child);
+ long pc;
+
+ pc = get_stack_long(child, (long)®s->pc);
+
+ /* Next scheduling will set up UBC */
+ if (child->thread.ubc_pc == 0)
+ ubc_usercnt += 1;
+
+ child->thread.ubc_pc = pc;
+
+ set_tsk_thread_flag(child, TIF_SINGLESTEP);
+}
+
+void user_disable_single_step(struct task_struct *child)
{
clear_tsk_thread_flag(child, TIF_SINGLESTEP);
*/
void ptrace_disable(struct task_struct *child)
{
- ptrace_disable_singlestep(child);
+ user_disable_single_step(child);
}
long arch_ptrace(struct task_struct *child, long request, long addr, long data)
int ret;
switch (request) {
- /* when I and D space are separate, these will need to be fixed. */
- case PTRACE_PEEKTEXT: /* read word at location addr. */
- case PTRACE_PEEKDATA:
- ret = generic_ptrace_peekdata(child, addr, data);
- break;
-
/* read the word at location addr in the USER area. */
case PTRACE_PEEKUSR: {
unsigned long tmp;
break;
}
- /* when I and D space are separate, this will have to be fixed. */
- case PTRACE_POKETEXT: /* write the word at location addr. */
- case PTRACE_POKEDATA:
- ret = generic_ptrace_pokedata(child, addr, data);
- break;
-
case PTRACE_POKEUSR: /* write the word at location addr in the USER area */
ret = -EIO;
if ((addr & 3) || addr < 0 ||
}
break;
- case PTRACE_SYSCALL: /* continue and stop at next (return from) syscall */
- case PTRACE_CONT: { /* restart after signal. */
- ret = -EIO;
- if (!valid_signal(data))
- break;
- if (request == PTRACE_SYSCALL)
- set_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- else
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
-
- ptrace_disable_singlestep(child);
-
- child->exit_code = data;
- wake_up_process(child);
- ret = 0;
- break;
- }
-
-/*
- * make the child exit. Best I can do is send it a sigkill.
- * perhaps it should be put in the status that it wants to
- * exit.
- */
- case PTRACE_KILL: {
- ret = 0;
- if (child->exit_state == EXIT_ZOMBIE) /* already dead */
- break;
- ptrace_disable_singlestep(child);
- child->exit_code = SIGKILL;
- wake_up_process(child);
- break;
- }
-
- case PTRACE_SINGLESTEP: { /* set the trap flag. */
- long pc;
- struct pt_regs *regs = NULL;
-
- ret = -EIO;
- if (!valid_signal(data))
- break;
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- if ((child->ptrace & PT_DTRACE) == 0) {
- /* Spurious delayed TF traps may occur */
- child->ptrace |= PT_DTRACE;
- }
-
- pc = get_stack_long(child, (long)®s->pc);
-
- /* Next scheduling will set up UBC */
- if (child->thread.ubc_pc == 0)
- ubc_usercnt += 1;
- child->thread.ubc_pc = pc;
-
- set_tsk_thread_flag(child, TIF_SINGLESTEP);
- child->exit_code = data;
- /* give it a chance to run. */
- wake_up_process(child);
- ret = 0;
- break;
- }
-
#ifdef CONFIG_SH_DSP
case PTRACE_GETDSPREGS: {
unsigned long dp;
return ret;
}
-asmlinkage void do_syscall_trace(struct pt_regs *regs, int entryexit)
+static inline int audit_arch(void)
{
- struct task_struct *tsk = current;
+ int arch = EM_SH;
- if (unlikely(current->audit_context) && entryexit)
- audit_syscall_exit(AUDITSC_RESULT(regs->regs[0]),
- regs->regs[0]);
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+ arch |= __AUDIT_ARCH_LE;
+#endif
- if (!test_thread_flag(TIF_SYSCALL_TRACE) &&
- !test_thread_flag(TIF_SINGLESTEP))
- goto out;
- if (!(tsk->ptrace & PT_PTRACED))
- goto out;
+ return arch;
+}
- /* the 0x80 provides a way for the tracing parent to distinguish
- between a syscall stop and SIGTRAP delivery */
- ptrace_notify(SIGTRAP | ((current->ptrace & PT_TRACESYSGOOD) &&
- !test_thread_flag(TIF_SINGLESTEP) ? 0x80 : 0));
+asmlinkage long do_syscall_trace_enter(struct pt_regs *regs)
+{
+ long ret = 0;
- /*
- * this isn't the same as continuing with a signal, but it will do
- * for normal use. strace only continues with a signal if the
- * stopping signal is not SIGTRAP. -brl
- */
- if (tsk->exit_code) {
- send_sig(tsk->exit_code, tsk, 1);
- tsk->exit_code = 0;
- }
+ secure_computing(regs->regs[0]);
+
+ if (test_thread_flag(TIF_SYSCALL_TRACE) &&
+ tracehook_report_syscall_entry(regs))
+ /*
+ * Tracing decided this syscall should not happen.
+ * We'll return a bogus call number to get an ENOSYS
+ * error, but leave the original number in regs->regs[0].
+ */
+ ret = -1L;
-out:
- if (unlikely(current->audit_context) && !entryexit)
- audit_syscall_entry(AUDIT_ARCH_SH, regs->regs[3],
+ if (unlikely(current->audit_context))
+ audit_syscall_entry(audit_arch(), regs->regs[3],
regs->regs[4], regs->regs[5],
regs->regs[6], regs->regs[7]);
+ return ret ?: regs->regs[0];
+}
+
+asmlinkage void do_syscall_trace_leave(struct pt_regs *regs)
+{
+ int step;
+
+ if (unlikely(current->audit_context))
+ audit_syscall_exit(AUDITSC_RESULT(regs->regs[0]),
+ regs->regs[0]);
+
+ step = test_thread_flag(TIF_SINGLESTEP);
+ if (step || test_thread_flag(TIF_SYSCALL_TRACE))
+ tracehook_report_syscall_exit(regs, step);
}
#include <linux/signal.h>
#include <linux/syscalls.h>
#include <linux/audit.h>
+#include <linux/seccomp.h>
+#include <linux/tracehook.h>
#include <asm/io.h>
#include <asm/uaccess.h>
#include <asm/pgtable.h>
return 0;
}
+void user_enable_single_step(struct task_struct *child)
+{
+ struct pt_regs *regs = child->thread.uregs;
+
+ regs->sr |= SR_SSTEP; /* auto-resetting upon exception */
+}
+
+void user_disable_single_step(struct task_struct *child)
+{
+ regs->sr &= ~SR_SSTEP;
+}
long arch_ptrace(struct task_struct *child, long request, long addr, long data)
{
int ret;
switch (request) {
- /* when I and D space are separate, these will need to be fixed. */
- case PTRACE_PEEKTEXT: /* read word at location addr. */
- case PTRACE_PEEKDATA:
- ret = generic_ptrace_peekdata(child, addr, data);
- break;
-
/* read the word at location addr in the USER area. */
case PTRACE_PEEKUSR: {
unsigned long tmp;
break;
}
- /* when I and D space are separate, this will have to be fixed. */
- case PTRACE_POKETEXT: /* write the word at location addr. */
- case PTRACE_POKEDATA:
- ret = generic_ptrace_pokedata(child, addr, data);
- break;
-
case PTRACE_POKEUSR:
/* write the word at location addr in the USER area. We must
disallow any changes to certain SR bits or u_fpvalid, since
}
break;
- case PTRACE_SYSCALL: /* continue and stop at next (return from) syscall */
- case PTRACE_CONT: { /* restart after signal. */
- ret = -EIO;
- if (!valid_signal(data))
- break;
- if (request == PTRACE_SYSCALL)
- set_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- else
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- child->exit_code = data;
- wake_up_process(child);
- ret = 0;
- break;
- }
-
-/*
- * make the child exit. Best I can do is send it a sigkill.
- * perhaps it should be put in the status that it wants to
- * exit.
- */
- case PTRACE_KILL: {
- ret = 0;
- if (child->exit_state == EXIT_ZOMBIE) /* already dead */
- break;
- child->exit_code = SIGKILL;
- wake_up_process(child);
- break;
- }
-
- case PTRACE_SINGLESTEP: { /* set the trap flag. */
- struct pt_regs *regs;
-
- ret = -EIO;
- if (!valid_signal(data))
- break;
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- if ((child->ptrace & PT_DTRACE) == 0) {
- /* Spurious delayed TF traps may occur */
- child->ptrace |= PT_DTRACE;
- }
-
- regs = child->thread.uregs;
-
- regs->sr |= SR_SSTEP; /* auto-resetting upon exception */
-
- child->exit_code = data;
- /* give it a chance to run. */
- wake_up_process(child);
- ret = 0;
- break;
- }
-
default:
ret = ptrace_request(child, request, addr, data);
break;
return sys_ptrace(request, pid, addr, data);
}
-asmlinkage void syscall_trace(struct pt_regs *regs, int entryexit)
+static inline int audit_arch(void)
{
- struct task_struct *tsk = current;
+ int arch = EM_SH;
- if (unlikely(current->audit_context) && entryexit)
- audit_syscall_exit(AUDITSC_RESULT(regs->regs[9]),
- regs->regs[9]);
+#ifdef CONFIG_64BIT
+ arch |= __AUDIT_ARCH_64BIT;
+#endif
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+ arch |= __AUDIT_ARCH_LE;
+#endif
- if (!test_thread_flag(TIF_SYSCALL_TRACE) &&
- !test_thread_flag(TIF_SINGLESTEP))
- goto out;
- if (!(tsk->ptrace & PT_PTRACED))
- goto out;
-
- ptrace_notify(SIGTRAP | ((current->ptrace & PT_TRACESYSGOOD) &&
- !test_thread_flag(TIF_SINGLESTEP) ? 0x80 : 0));
-
- /*
- * this isn't the same as continuing with a signal, but it will do
- * for normal use. strace only continues with a signal if the
- * stopping signal is not SIGTRAP. -brl
- */
- if (tsk->exit_code) {
- send_sig(tsk->exit_code, tsk, 1);
- tsk->exit_code = 0;
- }
+ return arch;
+}
-out:
- if (unlikely(current->audit_context) && !entryexit)
- audit_syscall_entry(AUDIT_ARCH_SH, regs->regs[1],
+asmlinkage long long do_syscall_trace_enter(struct pt_regs *regs)
+{
+ long long ret = 0;
+
+ secure_computing(regs->regs[9]);
+
+ if (test_thread_flag(TIF_SYSCALL_TRACE) &&
+ tracehook_report_syscall_entry(regs))
+ /*
+ * Tracing decided this syscall should not happen.
+ * We'll return a bogus call number to get an ENOSYS
+ * error, but leave the original number in regs->regs[0].
+ */
+ ret = -1LL;
+
+ if (unlikely(current->audit_context))
+ audit_syscall_entry(audit_arch(), regs->regs[1],
regs->regs[2], regs->regs[3],
regs->regs[4], regs->regs[5]);
+
+ return ret ?: regs->regs[9];
+}
+
+asmlinkage void do_syscall_trace_leave(struct pt_regs *regs)
+{
+ if (unlikely(current->audit_context))
+ audit_syscall_exit(AUDITSC_RESULT(regs->regs[9]),
+ regs->regs[9]);
+
+ if (test_thread_flag(TIF_SYSCALL_TRACE))
+ tracehook_report_syscall_exit(regs, 0);
}
/* Called with interrupts disabled */
*/
void ptrace_disable(struct task_struct *child)
{
- /* nothing to do.. */
+ user_disable_single_step(child);
}
#include <linux/smp.h>
#include <linux/err.h>
#include <linux/debugfs.h>
+#include <linux/crash_dump.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/page.h>
extern void __init setup_memory(void);
#endif
+/*
+ * Note: elfcorehdr_addr is not just limited to vmcore. It is also used by
+ * is_kdump_kernel() to determine if we are booting after a panic. Hence
+ * ifdef it under CONFIG_CRASH_DUMP and not CONFIG_PROC_VMCORE.
+ */
+#ifdef CONFIG_CRASH_DUMP
+/* elfcorehdr= specifies the location of elf core header
+ * stored by the crashed kernel.
+ */
+static int __init parse_elfcorehdr(char *arg)
+{
+ if (!arg)
+ return -EINVAL;
+ elfcorehdr_addr = memparse(arg, &arg);
+ return 0;
+}
+early_param("elfcorehdr", parse_elfcorehdr);
+#endif
+
void __init setup_arch(char **cmdline_p)
{
enable_mmu();
#include <linux/binfmts.h>
#include <linux/freezer.h>
#include <linux/io.h>
+#include <linux/tracehook.h>
#include <asm/system.h>
#include <asm/ucontext.h>
#include <asm/uaccess.h>
switch (regs->regs[0]) {
case -ERESTART_RESTARTBLOCK:
case -ERESTARTNOHAND:
+ no_system_call_restart:
regs->regs[0] = -EINTR;
break;
case -ERESTARTSYS:
- if (!(ka->sa.sa_flags & SA_RESTART)) {
- regs->regs[0] = -EINTR;
- break;
- }
+ if (!(ka->sa.sa_flags & SA_RESTART))
+ goto no_system_call_restart;
/* fallthrough */
case -ERESTARTNOINTR:
regs->regs[0] = save_r0;
* clear the TIF_RESTORE_SIGMASK flag */
if (test_thread_flag(TIF_RESTORE_SIGMASK))
clear_thread_flag(TIF_RESTORE_SIGMASK);
+
+ tracehook_signal_handler(signr, &info, &ka, regs,
+ test_thread_flag(TIF_SINGLESTEP));
}
return;
}
- no_signal:
+no_signal:
/* Did we come from a system call? */
if (regs->tra >= 0) {
/* Restart the system call - no handlers present */
}
asmlinkage void do_notify_resume(struct pt_regs *regs, unsigned int save_r0,
- __u32 thread_info_flags)
+ unsigned long thread_info_flags)
{
/* deal with pending signal delivery */
- if (thread_info_flags & (_TIF_SIGPENDING | _TIF_RESTORE_SIGMASK))
+ if (thread_info_flags & _TIF_SIGPENDING)
do_signal(regs, save_r0);
+
+ if (thread_info_flags & _TIF_NOTIFY_RESUME) {
+ clear_thread_flag(TIF_NOTIFY_RESUME);
+ tracehook_notify_resume(regs);
+ }
}
#include <linux/ptrace.h>
#include <linux/unistd.h>
#include <linux/stddef.h>
+#include <linux/tracehook.h>
#include <asm/ucontext.h>
#include <asm/uaccess.h>
#include <asm/pgtable.h>
#define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP)))
-asmlinkage int do_signal(struct pt_regs *regs, sigset_t *oldset);
+/*
+ * Note that 'init' is a special process: it doesn't get signals it doesn't
+ * want to handle. Thus you cannot kill init even with a SIGKILL even by
+ * mistake.
+ *
+ * Note that we go through the signals twice: once to check the signals that
+ * the kernel can handle, and then we build all the user-level signal handling
+ * stack-frames in one go after that.
+ */
+static int do_signal(struct pt_regs *regs, sigset_t *oldset)
+{
+ siginfo_t info;
+ int signr;
+ struct k_sigaction ka;
+
+ /*
+ * We want the common case to go fast, which
+ * is why we may in certain cases get here from
+ * kernel mode. Just return without doing anything
+ * if so.
+ */
+ if (!user_mode(regs))
+ return 1;
+
+ if (try_to_freeze())
+ goto no_signal;
+
+ if (test_thread_flag(TIF_RESTORE_SIGMASK))
+ oldset = ¤t->saved_sigmask;
+ else if (!oldset)
+ oldset = ¤t->blocked;
+
+ signr = get_signal_to_deliver(&info, &ka, regs, 0);
+
+ if (signr > 0) {
+ /* Whee! Actually deliver the signal. */
+ handle_signal(signr, &info, &ka, oldset, regs);
+
+ /*
+ * If a signal was successfully delivered, the saved sigmask
+ * is in its frame, and we can clear the TIF_RESTORE_SIGMASK
+ * flag.
+ */
+ if (test_thread_flag(TIF_RESTORE_SIGMASK))
+ clear_thread_flag(TIF_RESTORE_SIGMASK);
+
+ tracehook_signal_handler(signr, &info, &ka, regs, 0);
+ return 1;
+ }
+
+no_signal:
+ /* Did we come from a system call? */
+ if (regs->syscall_nr >= 0) {
+ /* Restart the system call - no handlers present */
+ switch (regs->regs[REG_RET]) {
+ case -ERESTARTNOHAND:
+ case -ERESTARTSYS:
+ case -ERESTARTNOINTR:
+ /* Decode Syscall # */
+ regs->regs[REG_RET] = regs->syscall_nr;
+ regs->pc -= 4;
+ break;
+
+ case -ERESTART_RESTARTBLOCK:
+ regs->regs[REG_RET] = __NR_restart_syscall;
+ regs->pc -= 4;
+ break;
+ }
+ }
+
+ /* No signal to deliver -- put the saved sigmask back */
+ if (test_thread_flag(TIF_RESTORE_SIGMASK)) {
+ clear_thread_flag(TIF_RESTORE_SIGMASK);
+ sigprocmask(SIG_SETMASK, ¤t->saved_sigmask, NULL);
+ }
+
+ return 0;
+}
/*
* Atomically swap in the new signal mask, and wait for a signal.
switch (regs->regs[REG_RET]) {
case -ERESTART_RESTARTBLOCK:
case -ERESTARTNOHAND:
+ no_system_call_restart:
regs->regs[REG_RET] = -EINTR;
break;
case -ERESTARTSYS:
- if (!(ka->sa.sa_flags & SA_RESTART)) {
- regs->regs[REG_RET] = -EINTR;
- break;
- }
+ if (!(ka->sa.sa_flags & SA_RESTART))
+ goto no_system_call_restart;
/* fallthrough */
case -ERESTARTNOINTR:
/* Decode syscall # */
spin_unlock_irq(¤t->sighand->siglock);
}
-/*
- * Note that 'init' is a special process: it doesn't get signals it doesn't
- * want to handle. Thus you cannot kill init even with a SIGKILL even by
- * mistake.
- *
- * Note that we go through the signals twice: once to check the signals that
- * the kernel can handle, and then we build all the user-level signal handling
- * stack-frames in one go after that.
- */
-int do_signal(struct pt_regs *regs, sigset_t *oldset)
+asmlinkage void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
{
- siginfo_t info;
- int signr;
- struct k_sigaction ka;
-
- /*
- * We want the common case to go fast, which
- * is why we may in certain cases get here from
- * kernel mode. Just return without doing anything
- * if so.
- */
- if (!user_mode(regs))
- return 1;
-
- if (try_to_freeze())
- goto no_signal;
-
- if (test_thread_flag(TIF_RESTORE_SIGMASK))
- oldset = ¤t->saved_sigmask;
- else if (!oldset)
- oldset = ¤t->blocked;
-
- signr = get_signal_to_deliver(&info, &ka, regs, 0);
-
- if (signr > 0) {
- /* Whee! Actually deliver the signal. */
- handle_signal(signr, &info, &ka, oldset, regs);
+ if (thread_info_flags & _TIF_SIGPENDING)
+ do_signal(regs, 0);
- /*
- * If a signal was successfully delivered, the saved sigmask
- * is in its frame, and we can clear the TIF_RESTORE_SIGMASK
- * flag.
- */
- if (test_thread_flag(TIF_RESTORE_SIGMASK))
- clear_thread_flag(TIF_RESTORE_SIGMASK);
-
- return 1;
+ if (thread_info_flags & _TIF_NOTIFY_RESUME) {
+ clear_thread_flag(TIF_NOTIFY_RESUME);
+ tracehook_notify_resume(regs);
}
-
-no_signal:
- /* Did we come from a system call? */
- if (regs->syscall_nr >= 0) {
- /* Restart the system call - no handlers present */
- switch (regs->regs[REG_RET]) {
- case -ERESTARTNOHAND:
- case -ERESTARTSYS:
- case -ERESTARTNOINTR:
- /* Decode Syscall # */
- regs->regs[REG_RET] = regs->syscall_nr;
- regs->pc -= 4;
- break;
-
- case -ERESTART_RESTARTBLOCK:
- regs->regs[REG_RET] = __NR_restart_syscall;
- regs->pc -= 4;
- break;
- }
- }
-
- /* No signal to deliver -- put the saved sigmask back */
- if (test_thread_flag(TIF_RESTORE_SIGMASK)) {
- clear_thread_flag(TIF_RESTORE_SIGMASK);
- sigprocmask(SIG_SETMASK, ¤t->saved_sigmask, NULL);
- }
-
- return 0;
}
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/platform_device.h>
-#include <asm/cpu/registers.h> /* required by inline __asm__ stmt. */
-#include <asm/cpu/irq.h>
+#include <cpu/registers.h> /* required by inline __asm__ stmt. */
+#include <cpu/irq.h>
#include <asm/addrspace.h>
#include <asm/processor.h>
#include <asm/uaccess.h>
#include <linux/kernel.h>
#include <asm/io.h>
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
/* THIS IS A PHYSICAL ADDRESS */
#define HDSP2534_ADDR (0x04002100)
config CACHE_WRITEBACK
bool "Write-back"
- depends on CPU_SH2A || CPU_SH3 || CPU_SH4 || CPU_SH5
config CACHE_WRITETHROUGH
bool "Write-through"
obj-y := init.o extable_32.o consistent.o
ifndef CONFIG_CACHE_OFF
-obj-$(CONFIG_CPU_SH2) += cache-sh2.o
-obj-$(CONFIG_CPU_SH3) += cache-sh3.o
-obj-$(CONFIG_CPU_SH4) += cache-sh4.o
-obj-$(CONFIG_SH7705_CACHE_32KB) += cache-sh7705.o
+cache-$(CONFIG_CPU_SH2) := cache-sh2.o
+cache-$(CONFIG_CPU_SH2A) := cache-sh2a.o
+cache-$(CONFIG_CPU_SH3) := cache-sh3.o
+cache-$(CONFIG_CPU_SH4) := cache-sh4.o
+cache-$(CONFIG_SH7705_CACHE_32KB) += cache-sh7705.o
endif
+obj-y += $(cache-y)
+
mmu-y := tlb-nommu.o pg-nommu.o
mmu-$(CONFIG_MMU) := fault_32.o tlbflush_32.o ioremap_32.o
* arch/sh/mm/cache-sh2.c
*
* Copyright (C) 2002 Paul Mundt
+ * Copyright (C) 2008 Yoshinori Sato
*
* Released under the terms of the GNU GPL v2.0.
*/
end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
& ~(L1_CACHE_BYTES-1);
for (v = begin; v < end; v+=L1_CACHE_BYTES) {
- /* FIXME cache purge */
- ctrl_outl((v & 0x1ffffc00), (v & 0x00000ff0) | 0x00000008);
+ unsigned long addr = CACHE_OC_ADDRESS_ARRAY | (v & 0x00000ff0);
+ int way;
+ for (way = 0; way < 4; way++) {
+ unsigned long data = ctrl_inl(addr | (way << 12));
+ if ((data & CACHE_PHYSADDR_MASK) == (v & CACHE_PHYSADDR_MASK)) {
+ data &= ~SH_CACHE_UPDATED;
+ ctrl_outl(data, addr | (way << 12));
+ }
+ }
}
}
begin = (unsigned long)start & ~(L1_CACHE_BYTES-1);
end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
& ~(L1_CACHE_BYTES-1);
- for (v = begin; v < end; v+=L1_CACHE_BYTES) {
- ctrl_outl((v & 0x1ffffc00), (v & 0x00000ff0) | 0x00000008);
- }
+
+ for (v = begin; v < end; v+=L1_CACHE_BYTES)
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_OC_ADDRESS_ARRAY | (v & 0x00000ff0) | 0x00000008);
}
void __flush_invalidate_region(void *start, int size)
{
+#ifdef CONFIG_CACHE_WRITEBACK
+ /*
+ * SH-2 does not support individual line invalidation, only a
+ * global invalidate.
+ */
+ unsigned long ccr;
+ unsigned long flags;
+ local_irq_save(flags);
+ jump_to_uncached();
+
+ ccr = ctrl_inl(CCR);
+ ccr |= CCR_CACHE_INVALIDATE;
+ ctrl_outl(ccr, CCR);
+
+ back_to_cached();
+ local_irq_restore(flags);
+#else
unsigned long v;
unsigned long begin, end;
begin = (unsigned long)start & ~(L1_CACHE_BYTES-1);
end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
& ~(L1_CACHE_BYTES-1);
- for (v = begin; v < end; v+=L1_CACHE_BYTES) {
- ctrl_outl((v & 0x1ffffc00), (v & 0x00000ff0) | 0x00000008);
- }
-}
+ for (v = begin; v < end; v+=L1_CACHE_BYTES)
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_OC_ADDRESS_ARRAY | (v & 0x00000ff0) | 0x00000008);
+#endif
+}
--- /dev/null
+/*
+ * arch/sh/mm/cache-sh2a.c
+ *
+ * Copyright (C) 2008 Yoshinori Sato
+ *
+ * Released under the terms of the GNU GPL v2.0.
+ */
+
+#include <linux/init.h>
+#include <linux/mm.h>
+
+#include <asm/cache.h>
+#include <asm/addrspace.h>
+#include <asm/processor.h>
+#include <asm/cacheflush.h>
+#include <asm/io.h>
+
+void __flush_wback_region(void *start, int size)
+{
+ unsigned long v;
+ unsigned long begin, end;
+ unsigned long flags;
+
+ begin = (unsigned long)start & ~(L1_CACHE_BYTES-1);
+ end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
+ & ~(L1_CACHE_BYTES-1);
+
+ local_irq_save(flags);
+ jump_to_uncached();
+
+ for (v = begin; v < end; v+=L1_CACHE_BYTES) {
+ unsigned long addr = CACHE_OC_ADDRESS_ARRAY | (v & 0x000007f0);
+ int way;
+ for (way = 0; way < 4; way++) {
+ unsigned long data = ctrl_inl(addr | (way << 11));
+ if ((data & CACHE_PHYSADDR_MASK) == (v & CACHE_PHYSADDR_MASK)) {
+ data &= ~SH_CACHE_UPDATED;
+ ctrl_outl(data, addr | (way << 11));
+ }
+ }
+ }
+
+ back_to_cached();
+ local_irq_restore(flags);
+}
+
+void __flush_purge_region(void *start, int size)
+{
+ unsigned long v;
+ unsigned long begin, end;
+ unsigned long flags;
+
+ begin = (unsigned long)start & ~(L1_CACHE_BYTES-1);
+ end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
+ & ~(L1_CACHE_BYTES-1);
+
+ local_irq_save(flags);
+ jump_to_uncached();
+
+ for (v = begin; v < end; v+=L1_CACHE_BYTES) {
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_OC_ADDRESS_ARRAY | (v & 0x000003f0) | 0x00000008);
+ }
+ back_to_cached();
+ local_irq_restore(flags);
+}
+
+void __flush_invalidate_region(void *start, int size)
+{
+ unsigned long v;
+ unsigned long begin, end;
+ unsigned long flags;
+
+ begin = (unsigned long)start & ~(L1_CACHE_BYTES-1);
+ end = ((unsigned long)start + size + L1_CACHE_BYTES-1)
+ & ~(L1_CACHE_BYTES-1);
+ local_irq_save(flags);
+ jump_to_uncached();
+
+#ifdef CONFIG_CACHE_WRITEBACK
+ ctrl_outl(ctrl_inl(CCR) | CCR_OCACHE_INVALIDATE, CCR);
+ /* I-cache invalidate */
+ for (v = begin; v < end; v+=L1_CACHE_BYTES) {
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_IC_ADDRESS_ARRAY | (v & 0x000003f0) | 0x00000008);
+ }
+#else
+ for (v = begin; v < end; v+=L1_CACHE_BYTES) {
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_IC_ADDRESS_ARRAY | (v & 0x000003f0) | 0x00000008);
+ ctrl_outl((v & CACHE_PHYSADDR_MASK),
+ CACHE_OC_ADDRESS_ARRAY | (v & 0x000003f0) | 0x00000008);
+ }
+#endif
+ back_to_cached();
+ local_irq_restore(flags);
+}
+
+/* WBack O-Cache and flush I-Cache */
+void flush_icache_range(unsigned long start, unsigned long end)
+{
+ unsigned long v;
+ unsigned long flags;
+
+ start = start & ~(L1_CACHE_BYTES-1);
+ end = (end + L1_CACHE_BYTES-1) & ~(L1_CACHE_BYTES-1);
+
+ local_irq_save(flags);
+ jump_to_uncached();
+
+ for (v = start; v < end; v+=L1_CACHE_BYTES) {
+ unsigned long addr = (v & 0x000007f0);
+ int way;
+ /* O-Cache writeback */
+ for (way = 0; way < 4; way++) {
+ unsigned long data = ctrl_inl(CACHE_OC_ADDRESS_ARRAY | addr | (way << 11));
+ if ((data & CACHE_PHYSADDR_MASK) == (v & CACHE_PHYSADDR_MASK)) {
+ data &= ~SH_CACHE_UPDATED;
+ ctrl_outl(data, CACHE_OC_ADDRESS_ARRAY | addr | (way << 11));
+ }
+ }
+ /* I-Cache invalidate */
+ ctrl_outl(addr,
+ CACHE_IC_ADDRESS_ARRAY | addr | 0x00000008);
+ }
+
+ back_to_cached();
+ local_irq_restore(flags);
+}
#include <asm/uaccess.h>
#include <asm/pgalloc.h>
#include <asm/mmu_context.h>
-#include <asm/cpu/registers.h>
+#include <cpu/registers.h>
/* Callable from fault.c, so not static */
inline void __do_tlb_refill(unsigned long address,
#include <asm/mmu_context.h>
/**
- * sh64_tlb_init
- *
- * Perform initial setup for the DTLB and ITLB.
+ * sh64_tlb_init - Perform initial setup for the DTLB and ITLB.
*/
int __init sh64_tlb_init(void)
{
}
/**
- * sh64_next_free_dtlb_entry
- *
- * Find the next available DTLB entry
+ * sh64_next_free_dtlb_entry - Find the next available DTLB entry
*/
unsigned long long sh64_next_free_dtlb_entry(void)
{
}
/**
- * sh64_get_wired_dtlb_entry
- *
- * Allocate a wired (locked-in) entry in the DTLB
+ * sh64_get_wired_dtlb_entry - Allocate a wired (locked-in) entry in the DTLB
*/
unsigned long long sh64_get_wired_dtlb_entry(void)
{
}
/**
- * sh64_put_wired_dtlb_entry
+ * sh64_put_wired_dtlb_entry - Free a wired (locked-in) entry in the DTLB.
*
* @entry: Address of TLB slot.
*
- * Free a wired (locked-in) entry in the DTLB.
- *
* Works like a stack, last one to allocate must be first one to free.
*/
int sh64_put_wired_dtlb_entry(unsigned long long entry)
}
/**
- * sh64_setup_tlb_slot
+ * sh64_setup_tlb_slot - Load up a translation in a wired slot.
*
* @config_addr: Address of TLB slot.
* @eaddr: Virtual address.
}
/**
- * sh64_teardown_tlb_slot
+ * sh64_teardown_tlb_slot - Teardown a translation.
*
* @config_addr: Address of TLB slot.
*
#ifndef _LINUX_IOPORT_H
#include <linux/ioport.h>
#endif
+#include <linux/of_device.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
struct linux_ebus_child {
struct linux_ebus_child *next;
#ifndef __SPARC64_EBUS_H
#define __SPARC64_EBUS_H
+#include <linux/of_device.h>
+
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
struct linux_ebus_child {
struct linux_ebus_child *next;
__futex_cas_op("or\t%2, %4, %1", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_ANDN:
- __futex_cas_op("and\t%2, %4, %1", ret, oldval, uaddr, oparg);
+ __futex_cas_op("andn\t%2, %4, %1", ret, oldval, uaddr, oparg);
break;
case FUTEX_OP_XOR:
__futex_cas_op("xor\t%2, %4, %1", ret, oldval, uaddr, oparg);
return retval;
}
+void __trigger_all_cpu_backtrace(void);
+#define trigger_all_cpu_backtrace() __trigger_all_cpu_backtrace()
+
#endif
#ifndef ___ASM_SPARC_OF_PLATFORM_H
#define ___ASM_SPARC_OF_PLATFORM_H
-#if defined(__sparc__) && defined(__arch64__)
-#include <asm/of_platform_64.h>
-#else
-#include <asm/of_platform_32.h>
-#endif
+/*
+ * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corp.
+ * <benh@kernel.crashing.org>
+ * Modified for Sparc by merging parts of asm/of_device.h
+ * by Stephen Rothwell
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ */
+
+extern struct bus_type ebus_bus_type;
+extern struct bus_type sbus_bus_type;
+
+#define of_bus_type of_platform_bus_type /* for compatibility */
+
#endif
+++ /dev/null
-#ifndef _ASM_SPARC_OF_PLATFORM_H
-#define _ASM_SPARC_OF_PLATFORM_H
-/*
- * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corp.
- * <benh@kernel.crashing.org>
- * Modified for Sparc by merging parts of asm/of_device.h
- * by Stephen Rothwell
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- *
- */
-
-/* This is just here during the transition */
-#include <linux/of_platform.h>
-
-extern struct bus_type ebus_bus_type;
-extern struct bus_type sbus_bus_type;
-
-#define of_bus_type of_platform_bus_type /* for compatibility */
-
-#endif /* _ASM_SPARC_OF_PLATFORM_H */
+++ /dev/null
-#ifndef _ASM_SPARC64_OF_PLATFORM_H
-#define _ASM_SPARC64_OF_PLATFORM_H
-/*
- * Copyright (C) 2006 Benjamin Herrenschmidt, IBM Corp.
- * <benh@kernel.crashing.org>
- * Modified for Sparc by merging parts of asm/of_device.h
- * by Stephen Rothwell
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- *
- */
-
-/* This is just here during the transition */
-#include <linux/of_platform.h>
-
-extern struct bus_type isa_bus_type;
-extern struct bus_type ebus_bus_type;
-extern struct bus_type sbus_bus_type;
-
-#define of_bus_type of_platform_bus_type /* for compatibility */
-
-#endif /* _ASM_SPARC64_OF_PLATFORM_H */
#ifndef _ASM_SPARC64_PARPORT_H
#define _ASM_SPARC64_PARPORT_H 1
+#include <linux/of_device.h>
+
#include <asm/ebus.h>
#include <asm/ns87303.h>
-#include <asm/of_device.h>
#include <asm/prom.h>
#define PARPORT_PC_MAX_PORTS PARPORT_MAX
#define UREG_FP UREG_I6
#define UREG_RETPC UREG_I7
-static inline bool pt_regs_is_syscall(struct pt_regs *regs)
-{
- return (regs->psr & PSR_SYSCALL);
-}
-
-static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
-{
- return (regs->psr &= ~PSR_SYSCALL);
-}
-
/* A register window */
struct reg_window {
unsigned long locals[8];
#ifdef __KERNEL__
+static inline bool pt_regs_is_syscall(struct pt_regs *regs)
+{
+ return (regs->psr & PSR_SYSCALL);
+}
+
+static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
+{
+ return (regs->psr &= ~PSR_SYSCALL);
+}
+
#define user_mode(regs) (!((regs)->psr & PSR_PS))
#define instruction_pointer(regs) ((regs)->pc)
#define user_stack_pointer(regs) ((regs)->u_regs[UREG_FP])
unsigned int magic;
};
-static inline int pt_regs_trap_type(struct pt_regs *regs)
-{
- return regs->magic & 0x1ff;
-}
-
-static inline bool pt_regs_is_syscall(struct pt_regs *regs)
-{
- return (regs->tstate & TSTATE_SYSCALL);
-}
-
-static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
-{
- return (regs->tstate &= ~TSTATE_SYSCALL);
-}
-
struct pt_regs32 {
unsigned int psr;
unsigned int pc;
#ifdef __KERNEL__
+static inline int pt_regs_trap_type(struct pt_regs *regs)
+{
+ return regs->magic & 0x1ff;
+}
+
+static inline bool pt_regs_is_syscall(struct pt_regs *regs)
+{
+ return (regs->tstate & TSTATE_SYSCALL);
+}
+
+static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
+{
+ return (regs->tstate &= ~TSTATE_SYSCALL);
+}
+
struct global_reg_snapshot {
unsigned long tstate;
unsigned long tpc;
unsigned long tnpc;
unsigned long o7;
unsigned long i7;
+ unsigned long rpc;
struct thread_info *thread;
unsigned long pad1;
- unsigned long pad2;
};
#define __ARCH_WANT_COMPAT_SYS_PTRACE
#define profile_pc(regs) instruction_pointer(regs)
#endif
extern void show_regs(struct pt_regs *);
-extern void __show_regs(struct pt_regs *);
#endif
#else /* __ASSEMBLY__ */
#define GR_SNAP_TNPC 0x10
#define GR_SNAP_O7 0x18
#define GR_SNAP_I7 0x20
-#define GR_SNAP_THREAD 0x28
-#define GR_SNAP_PAD1 0x30
-#define GR_SNAP_PAD2 0x38
+#define GR_SNAP_RPC 0x28
+#define GR_SNAP_THREAD 0x30
+#define GR_SNAP_PAD1 0x38
#endif /* __KERNEL__ */
#include <linux/dma-mapping.h>
#include <linux/ioport.h>
+#include <linux/of_device.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/scatterlist.h>
/* We scan which devices are on the SBus using the PROM node device
#include <linux/dma-mapping.h>
#include <linux/ioport.h>
+#include <linux/of_device.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/iommu.h>
#include <asm/scatterlist.h>
#include <linux/pci.h> /* struct pci_dev */
#include <linux/proc_fs.h>
#include <linux/scatterlist.h>
+#include <linux/of_device.h>
#include <asm/io.h>
#include <asm/vaddrs.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/sbus.h>
#include <asm/page.h>
#include <asm/pgalloc.h>
#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/profile.h>
+#include <linux/of_device.h>
#include <asm/oplib.h>
#include <asm/timer.h>
#include <asm/sun4paddr.h>
#include <asm/page.h>
#include <asm/pcic.h>
-#include <asm/of_device.h>
#include <asm/irq_regs.h>
#include "irq.h"
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/ioport.h>
+#include <linux/of_device.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/io.h>
#include <asm/auxio.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/pci.h>
+#include <linux/of_device.h>
#include <asm/system.h>
#include <asm/page.h>
#include <asm/ebus.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/bpp.h>
#include <asm/irq.h>
#include <asm/io.h>
alloc_one_mondo(&tb->nonresum_mondo_pa, tb->nonresum_qmask);
alloc_one_kbuf(&tb->nonresum_kernel_buf_pa,
tb->nonresum_qmask);
+ }
+}
+
+static void __init init_send_mondo_info(void)
+{
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ struct trap_per_cpu *tb = &trap_block[cpu];
init_cpu_send_mondo_info(tb);
}
-
- /* Load up the boot cpu's entries. */
- sun4v_register_mondo_queues(hard_smp_processor_id());
}
static struct irqaction timer_irq_action = {
if (tlb_type == hypervisor)
sun4v_init_mondo_queues();
+ init_send_mondo_info();
+
+ if (tlb_type == hypervisor) {
+ /* Load up the boot cpu's entries. */
+ sun4v_register_mondo_queues(hard_smp_processor_id());
+ }
+
/* We need to clear any IRQ's pending in the soft interrupt
* registers, a spurious one could be left around from the
* PROM timer which we just disabled.
EXPORT_SYMBOL(of_find_device_by_node);
#ifdef CONFIG_PCI
-struct bus_type isa_bus_type;
-EXPORT_SYMBOL(isa_bus_type);
-
struct bus_type ebus_bus_type;
EXPORT_SYMBOL(ebus_bus_type);
#endif
err = of_bus_type_init(&of_platform_bus_type, "of");
#ifdef CONFIG_PCI
- if (!err)
- err = of_bus_type_init(&isa_bus_type, "isa");
if (!err)
err = of_bus_type_init(&ebus_bus_type, "ebus");
#endif
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/device.h>
+#include <linux/of_device.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/oplib.h>
#include "pci_impl.h"
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
+#include <linux/of_device.h>
#include <asm/iommu.h>
#include <asm/irq.h>
#include <asm/starfire.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/oplib.h>
#include "pci_impl.h"
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
+#include <linux/of_device.h>
#include <asm/apb.h>
#include <asm/iommu.h>
#include <asm/smp.h>
#include <asm/oplib.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include "pci_impl.h"
#include "iommu_common.h"
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
+#include <linux/of_device.h>
#include <asm/iommu.h>
#include <asm/irq.h>
#include <asm/upa.h>
#include <asm/pstate.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/oplib.h>
#include "pci_impl.h"
#include <linux/pm.h>
#include <linux/syscalls.h>
#include <linux/reboot.h>
+#include <linux/of_device.h>
#include <asm/system.h>
#include <asm/auxio.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/io.h>
#include <asm/sstate.h>
#include <asm/reboot.h>
#include <asm/irq_regs.h>
#include <asm/smp.h>
-/* #define VERBOSE_SHOWREGS */
-
static void sparc64_yield(int cpu)
{
if (tlb_type != hypervisor)
printk("I7: <%pS>\n", (void *) rwk->ins[7]);
}
-#ifdef CONFIG_SMP
-static DEFINE_SPINLOCK(regdump_lock);
-#endif
-
-void __show_regs(struct pt_regs * regs)
+void show_regs(struct pt_regs *regs)
{
-#ifdef CONFIG_SMP
- unsigned long flags;
-
- /* Protect against xcall ipis which might lead to livelock on the lock */
- __asm__ __volatile__("rdpr %%pstate, %0\n\t"
- "wrpr %0, %1, %%pstate"
- : "=r" (flags)
- : "i" (PSTATE_IE));
- spin_lock(®dump_lock);
-#endif
printk("TSTATE: %016lx TPC: %016lx TNPC: %016lx Y: %08x %s\n", regs->tstate,
regs->tpc, regs->tnpc, regs->y, print_tainted());
printk("TPC: <%pS>\n", (void *) regs->tpc);
regs->u_regs[15]);
printk("RPC: <%pS>\n", (void *) regs->u_regs[15]);
show_regwindow(regs);
-#ifdef CONFIG_SMP
- spin_unlock(®dump_lock);
- __asm__ __volatile__("wrpr %0, 0, %%pstate"
- : : "r" (flags));
-#endif
}
-#ifdef VERBOSE_SHOWREGS
-static void idump_from_user (unsigned int *pc)
-{
- int i;
- int code;
-
- if((((unsigned long) pc) & 3))
- return;
-
- pc -= 3;
- for(i = -3; i < 6; i++) {
- get_user(code, pc);
- printk("%c%08x%c",i?' ':'<',code,i?' ':'>');
- pc++;
- }
- printk("\n");
-}
-#endif
+struct global_reg_snapshot global_reg_snapshot[NR_CPUS];
+static DEFINE_SPINLOCK(global_reg_snapshot_lock);
-void show_regs(struct pt_regs *regs)
+static bool kstack_valid(struct thread_info *tp, struct reg_window *rw)
{
-#ifdef VERBOSE_SHOWREGS
- extern long etrap, etraptl1;
-#endif
- __show_regs(regs);
-#if 0
-#ifdef CONFIG_SMP
- {
- extern void smp_report_regs(void);
+ unsigned long thread_base, fp;
- smp_report_regs();
- }
-#endif
-#endif
+ thread_base = (unsigned long) tp;
+ fp = (unsigned long) rw;
-#ifdef VERBOSE_SHOWREGS
- if (regs->tpc >= &etrap && regs->tpc < &etraptl1 &&
- regs->u_regs[14] >= (long)current - PAGE_SIZE &&
- regs->u_regs[14] < (long)current + 6 * PAGE_SIZE) {
- printk ("*********parent**********\n");
- __show_regs((struct pt_regs *)(regs->u_regs[14] + PTREGS_OFF));
- idump_from_user(((struct pt_regs *)(regs->u_regs[14] + PTREGS_OFF))->tpc);
- printk ("*********endpar**********\n");
- }
-#endif
+ if (fp < (thread_base + sizeof(struct thread_info)) ||
+ fp >= (thread_base + THREAD_SIZE))
+ return false;
+ return true;
}
-#ifdef CONFIG_MAGIC_SYSRQ
-struct global_reg_snapshot global_reg_snapshot[NR_CPUS];
-static DEFINE_SPINLOCK(global_reg_snapshot_lock);
-
static void __global_reg_self(struct thread_info *tp, struct pt_regs *regs,
int this_cpu)
{
global_reg_snapshot[this_cpu].o7 = regs->u_regs[UREG_I7];
if (regs->tstate & TSTATE_PRIV) {
+ struct thread_info *tp = current_thread_info();
struct reg_window *rw;
rw = (struct reg_window *)
(regs->u_regs[UREG_FP] + STACK_BIAS);
- global_reg_snapshot[this_cpu].i7 = rw->ins[6];
- } else
+ if (kstack_valid(tp, rw)) {
+ global_reg_snapshot[this_cpu].i7 = rw->ins[7];
+ rw = (struct reg_window *)
+ (rw->ins[6] + STACK_BIAS);
+ if (kstack_valid(tp, rw))
+ global_reg_snapshot[this_cpu].rpc = rw->ins[7];
+ }
+ } else {
global_reg_snapshot[this_cpu].i7 = 0;
-
+ global_reg_snapshot[this_cpu].rpc = 0;
+ }
global_reg_snapshot[this_cpu].thread = tp;
}
}
}
-static void sysrq_handle_globreg(int key, struct tty_struct *tty)
+void __trigger_all_cpu_backtrace(void)
{
struct thread_info *tp = current_thread_info();
struct pt_regs *regs = get_irq_regs();
((tp && tp->task) ? tp->task->pid : -1));
if (gp->tstate & TSTATE_PRIV) {
- printk(" TPC[%pS] O7[%pS] I7[%pS]\n",
+ printk(" TPC[%pS] O7[%pS] I7[%pS] RPC[%pS]\n",
(void *) gp->tpc,
(void *) gp->o7,
- (void *) gp->i7);
+ (void *) gp->i7,
+ (void *) gp->rpc);
} else {
- printk(" TPC[%lx] O7[%lx] I7[%lx]\n",
- gp->tpc, gp->o7, gp->i7);
+ printk(" TPC[%lx] O7[%lx] I7[%lx] RPC[%lx]\n",
+ gp->tpc, gp->o7, gp->i7, gp->rpc);
}
}
spin_unlock_irqrestore(&global_reg_snapshot_lock, flags);
}
+#ifdef CONFIG_MAGIC_SYSRQ
+
+static void sysrq_handle_globreg(int key, struct tty_struct *tty)
+{
+ __trigger_all_cpu_backtrace();
+}
+
static struct sysrq_key_op sparc_globalreg_op = {
.handler = sysrq_handle_globreg,
.help_msg = "Globalregs",
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/lmb.h>
+#include <linux/of_device.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/oplib.h>
#include <asm/irq.h>
#include <asm/asi.h>
* arch/sparc64/kernel/signal.c
*
* Copyright (C) 1991, 1992 Linus Torvalds
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ * Copyright (C) 1995, 2008 David S. Miller (davem@davemloft.net)
* Copyright (C) 1996 Miguel de Icaza (miguel@nuclecu.unam.mx)
* Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
* Copyright (C) 1997,1998 Jakub Jelinek (jj@sunsite.mff.cuni.cz)
#include <linux/tty.h>
#include <linux/binfmts.h>
#include <linux/bitops.h>
-#include <linux/tracehook.h>
#include <asm/uaccess.h>
#include <asm/ptrace.h>
err |= __get_user(regs->u_regs[UREG_G4], (&(*grp)[MC_G4]));
err |= __get_user(regs->u_regs[UREG_G5], (&(*grp)[MC_G5]));
err |= __get_user(regs->u_regs[UREG_G6], (&(*grp)[MC_G6]));
- err |= __get_user(regs->u_regs[UREG_G7], (&(*grp)[MC_G7]));
+
+ /* Skip %g7 as that's the thread register in userspace. */
+
err |= __get_user(regs->u_regs[UREG_I0], (&(*grp)[MC_O0]));
err |= __get_user(regs->u_regs[UREG_I1], (&(*grp)[MC_O1]));
err |= __get_user(regs->u_regs[UREG_I2], (&(*grp)[MC_O2]));
}
}
-static inline void spitfire_xcall_deliver(u64 data0, u64 data1, u64 data2, cpumask_t mask)
+static void spitfire_xcall_deliver(struct trap_per_cpu *tb, int cnt)
{
+ u64 *mondo, data0, data1, data2;
+ u16 *cpu_list;
u64 pstate;
int i;
__asm__ __volatile__("rdpr %%pstate, %0" : "=r" (pstate));
- for_each_cpu_mask(i, mask)
- spitfire_xcall_helper(data0, data1, data2, pstate, i);
+ cpu_list = __va(tb->cpu_list_pa);
+ mondo = __va(tb->cpu_mondo_block_pa);
+ data0 = mondo[0];
+ data1 = mondo[1];
+ data2 = mondo[2];
+ for (i = 0; i < cnt; i++)
+ spitfire_xcall_helper(data0, data1, data2, pstate, cpu_list[i]);
}
/* Cheetah now allows to send the whole 64-bytes of data in the interrupt
* packet, but we have no use for that. However we do take advantage of
* the new pipelining feature (ie. dispatch to multiple cpus simultaneously).
*/
-static void cheetah_xcall_deliver(u64 data0, u64 data1, u64 data2, cpumask_t mask)
+static void cheetah_xcall_deliver(struct trap_per_cpu *tb, int cnt)
{
- u64 pstate, ver, busy_mask;
int nack_busy_id, is_jbus, need_more;
+ u64 *mondo, pstate, ver, busy_mask;
+ u16 *cpu_list;
- if (cpus_empty(mask))
- return;
+ cpu_list = __va(tb->cpu_list_pa);
+ mondo = __va(tb->cpu_mondo_block_pa);
/* Unfortunately, someone at Sun had the brilliant idea to make the
* busy/nack fields hard-coded by ITID number for this Ultra-III
"stxa %2, [%5] %6\n\t"
"membar #Sync\n\t"
: /* no outputs */
- : "r" (data0), "r" (data1), "r" (data2),
+ : "r" (mondo[0]), "r" (mondo[1]), "r" (mondo[2]),
"r" (0x40), "r" (0x50), "r" (0x60),
"i" (ASI_INTR_W));
{
int i;
- for_each_cpu_mask(i, mask) {
- u64 target = (i << 14) | 0x70;
+ for (i = 0; i < cnt; i++) {
+ u64 target, nr;
+ nr = cpu_list[i];
+ if (nr == 0xffff)
+ continue;
+
+ target = (nr << 14) | 0x70;
if (is_jbus) {
- busy_mask |= (0x1UL << (i * 2));
+ busy_mask |= (0x1UL << (nr * 2));
} else {
target |= (nack_busy_id << 24);
busy_mask |= (0x1UL <<
__asm__ __volatile__("wrpr %0, 0x0, %%pstate"
: : "r" (pstate));
if (unlikely(need_more)) {
- int i, cnt = 0;
- for_each_cpu_mask(i, mask) {
- cpu_clear(i, mask);
- cnt++;
- if (cnt == 32)
+ int i, this_cnt = 0;
+ for (i = 0; i < cnt; i++) {
+ if (cpu_list[i] == 0xffff)
+ continue;
+ cpu_list[i] = 0xffff;
+ this_cnt++;
+ if (this_cnt == 32)
break;
}
goto retry;
/* Clear out the mask bits for cpus which did not
* NACK us.
*/
- for_each_cpu_mask(i, mask) {
- u64 check_mask;
+ for (i = 0; i < cnt; i++) {
+ u64 check_mask, nr;
+
+ nr = cpu_list[i];
+ if (nr == 0xffff)
+ continue;
if (is_jbus)
- check_mask = (0x2UL << (2*i));
+ check_mask = (0x2UL << (2*nr));
else
check_mask = (0x2UL <<
this_busy_nack);
if ((dispatch_stat & check_mask) == 0)
- cpu_clear(i, mask);
+ cpu_list[i] = 0xffff;
this_busy_nack += 2;
if (this_busy_nack == 64)
break;
}
/* Multi-cpu list version. */
-static void hypervisor_xcall_deliver(u64 data0, u64 data1, u64 data2, cpumask_t mask)
+static void hypervisor_xcall_deliver(struct trap_per_cpu *tb, int cnt)
{
- struct trap_per_cpu *tb;
+ int retries, this_cpu, prev_sent, i, saw_cpu_error;
+ unsigned long status;
u16 *cpu_list;
- u64 *mondo;
- cpumask_t error_mask;
- unsigned long flags, status;
- int cnt, retries, this_cpu, prev_sent, i;
-
- if (cpus_empty(mask))
- return;
-
- /* We have to do this whole thing with interrupts fully disabled.
- * Otherwise if we send an xcall from interrupt context it will
- * corrupt both our mondo block and cpu list state.
- *
- * One consequence of this is that we cannot use timeout mechanisms
- * that depend upon interrupts being delivered locally. So, for
- * example, we cannot sample jiffies and expect it to advance.
- *
- * Fortunately, udelay() uses %stick/%tick so we can use that.
- */
- local_irq_save(flags);
this_cpu = smp_processor_id();
- tb = &trap_block[this_cpu];
-
- mondo = __va(tb->cpu_mondo_block_pa);
- mondo[0] = data0;
- mondo[1] = data1;
- mondo[2] = data2;
- wmb();
cpu_list = __va(tb->cpu_list_pa);
- /* Setup the initial cpu list. */
- cnt = 0;
- for_each_cpu_mask(i, mask)
- cpu_list[cnt++] = i;
-
- cpus_clear(error_mask);
+ saw_cpu_error = 0;
retries = 0;
prev_sent = 0;
do {
continue;
err = sun4v_cpu_state(cpu);
- if (err >= 0 &&
- err == HV_CPU_STATE_ERROR) {
+ if (err == HV_CPU_STATE_ERROR) {
+ saw_cpu_error = (cpu + 1);
cpu_list[i] = 0xffff;
- cpu_set(cpu, error_mask);
}
}
} else if (unlikely(status != HV_EWOULDBLOCK))
}
} while (1);
- local_irq_restore(flags);
-
- if (unlikely(!cpus_empty(error_mask)))
+ if (unlikely(saw_cpu_error))
goto fatal_mondo_cpu_error;
return;
fatal_mondo_cpu_error:
printk(KERN_CRIT "CPU[%d]: SUN4V mondo cpu error, some target cpus "
- "were in error state\n",
- this_cpu);
- printk(KERN_CRIT "CPU[%d]: Error mask [ ", this_cpu);
- for_each_cpu_mask(i, error_mask)
- printk("%d ", i);
- printk("]\n");
+ "(including %d) were in error state\n",
+ this_cpu, saw_cpu_error - 1);
return;
fatal_mondo_timeout:
- local_irq_restore(flags);
printk(KERN_CRIT "CPU[%d]: SUN4V mondo timeout, no forward "
" progress after %d retries.\n",
this_cpu, retries);
goto dump_cpu_list_and_out;
fatal_mondo_error:
- local_irq_restore(flags);
printk(KERN_CRIT "CPU[%d]: Unexpected SUN4V mondo error %lu\n",
this_cpu, status);
printk(KERN_CRIT "CPU[%d]: Args were cnt(%d) cpulist_pa(%lx) "
printk("]\n");
}
-/* Send cross call to all processors mentioned in MASK
- * except self.
+static void (*xcall_deliver_impl)(struct trap_per_cpu *, int);
+
+static void xcall_deliver(u64 data0, u64 data1, u64 data2, const cpumask_t *mask)
+{
+ struct trap_per_cpu *tb;
+ int this_cpu, i, cnt;
+ unsigned long flags;
+ u16 *cpu_list;
+ u64 *mondo;
+
+ /* We have to do this whole thing with interrupts fully disabled.
+ * Otherwise if we send an xcall from interrupt context it will
+ * corrupt both our mondo block and cpu list state.
+ *
+ * One consequence of this is that we cannot use timeout mechanisms
+ * that depend upon interrupts being delivered locally. So, for
+ * example, we cannot sample jiffies and expect it to advance.
+ *
+ * Fortunately, udelay() uses %stick/%tick so we can use that.
+ */
+ local_irq_save(flags);
+
+ this_cpu = smp_processor_id();
+ tb = &trap_block[this_cpu];
+
+ mondo = __va(tb->cpu_mondo_block_pa);
+ mondo[0] = data0;
+ mondo[1] = data1;
+ mondo[2] = data2;
+ wmb();
+
+ cpu_list = __va(tb->cpu_list_pa);
+
+ /* Setup the initial cpu list. */
+ cnt = 0;
+ for_each_cpu_mask_nr(i, *mask) {
+ if (i == this_cpu || !cpu_online(i))
+ continue;
+ cpu_list[cnt++] = i;
+ }
+
+ if (cnt)
+ xcall_deliver_impl(tb, cnt);
+
+ local_irq_restore(flags);
+}
+
+/* Send cross call to all processors mentioned in MASK_P
+ * except self. Really, there are only two cases currently,
+ * "&cpu_online_map" and "&mm->cpu_vm_mask".
*/
-static void smp_cross_call_masked(unsigned long *func, u32 ctx, u64 data1, u64 data2, cpumask_t mask)
+static void smp_cross_call_masked(unsigned long *func, u32 ctx, u64 data1, u64 data2, const cpumask_t *mask)
{
u64 data0 = (((u64)ctx)<<32 | (((u64)func) & 0xffffffff));
- int this_cpu = get_cpu();
-
- cpus_and(mask, mask, cpu_online_map);
- cpu_clear(this_cpu, mask);
- if (tlb_type == spitfire)
- spitfire_xcall_deliver(data0, data1, data2, mask);
- else if (tlb_type == cheetah || tlb_type == cheetah_plus)
- cheetah_xcall_deliver(data0, data1, data2, mask);
- else
- hypervisor_xcall_deliver(data0, data1, data2, mask);
- /* NOTE: Caller runs local copy on master. */
+ xcall_deliver(data0, data1, data2, mask);
+}
- put_cpu();
+/* Send cross call to all processors except self. */
+static void smp_cross_call(unsigned long *func, u32 ctx, u64 data1, u64 data2)
+{
+ smp_cross_call_masked(func, ctx, data1, data2, &cpu_online_map);
}
extern unsigned long xcall_sync_tick;
static void smp_start_sync_tick_client(int cpu)
{
- cpumask_t mask = cpumask_of_cpu(cpu);
-
- smp_cross_call_masked(&xcall_sync_tick,
- 0, 0, 0, mask);
+ xcall_deliver((u64) &xcall_sync_tick, 0, 0,
+ &cpumask_of_cpu(cpu));
}
extern unsigned long xcall_call_function;
void arch_send_call_function_ipi(cpumask_t mask)
{
- smp_cross_call_masked(&xcall_call_function, 0, 0, 0, mask);
+ xcall_deliver((u64) &xcall_call_function, 0, 0, &mask);
}
extern unsigned long xcall_call_function_single;
void arch_send_call_function_single_ipi(int cpu)
{
- cpumask_t mask = cpumask_of_cpu(cpu);
-
- smp_cross_call_masked(&xcall_call_function_single, 0, 0, 0, mask);
+ xcall_deliver((u64) &xcall_call_function_single, 0, 0,
+ &cpumask_of_cpu(cpu));
}
-/* Send cross call to all processors except self. */
-#define smp_cross_call(func, ctx, data1, data2) \
- smp_cross_call_masked(func, ctx, data1, data2, cpu_online_map)
-
void smp_call_function_client(int irq, struct pt_regs *regs)
{
clear_softint(1 << irq);
extern unsigned long xcall_flush_tlb_mm;
extern unsigned long xcall_flush_tlb_pending;
extern unsigned long xcall_flush_tlb_kernel_range;
-extern unsigned long xcall_report_regs;
#ifdef CONFIG_MAGIC_SYSRQ
extern unsigned long xcall_fetch_glob_regs;
#endif
void smp_flush_dcache_page_impl(struct page *page, int cpu)
{
- cpumask_t mask = cpumask_of_cpu(cpu);
int this_cpu;
if (tlb_type == hypervisor)
__local_flush_dcache_page(page);
} else if (cpu_online(cpu)) {
void *pg_addr = page_address(page);
- u64 data0;
+ u64 data0 = 0;
if (tlb_type == spitfire) {
- data0 =
- ((u64)&xcall_flush_dcache_page_spitfire);
+ data0 = ((u64)&xcall_flush_dcache_page_spitfire);
if (page_mapping(page) != NULL)
data0 |= ((u64)1 << 32);
- spitfire_xcall_deliver(data0,
- __pa(pg_addr),
- (u64) pg_addr,
- mask);
} else if (tlb_type == cheetah || tlb_type == cheetah_plus) {
#ifdef DCACHE_ALIASING_POSSIBLE
- data0 =
- ((u64)&xcall_flush_dcache_page_cheetah);
- cheetah_xcall_deliver(data0,
- __pa(pg_addr),
- 0, mask);
+ data0 = ((u64)&xcall_flush_dcache_page_cheetah);
#endif
}
+ if (data0) {
+ xcall_deliver(data0, __pa(pg_addr),
+ (u64) pg_addr, &cpumask_of_cpu(cpu));
#ifdef CONFIG_DEBUG_DCFLUSH
- atomic_inc(&dcpage_flushes_xcall);
+ atomic_inc(&dcpage_flushes_xcall);
#endif
+ }
}
put_cpu();
void flush_dcache_page_all(struct mm_struct *mm, struct page *page)
{
- void *pg_addr = page_address(page);
- cpumask_t mask = cpu_online_map;
- u64 data0;
+ void *pg_addr;
int this_cpu;
+ u64 data0;
if (tlb_type == hypervisor)
return;
this_cpu = get_cpu();
- cpu_clear(this_cpu, mask);
-
#ifdef CONFIG_DEBUG_DCFLUSH
atomic_inc(&dcpage_flushes);
#endif
- if (cpus_empty(mask))
- goto flush_self;
+ data0 = 0;
+ pg_addr = page_address(page);
if (tlb_type == spitfire) {
data0 = ((u64)&xcall_flush_dcache_page_spitfire);
if (page_mapping(page) != NULL)
data0 |= ((u64)1 << 32);
- spitfire_xcall_deliver(data0,
- __pa(pg_addr),
- (u64) pg_addr,
- mask);
} else if (tlb_type == cheetah || tlb_type == cheetah_plus) {
#ifdef DCACHE_ALIASING_POSSIBLE
data0 = ((u64)&xcall_flush_dcache_page_cheetah);
- cheetah_xcall_deliver(data0,
- __pa(pg_addr),
- 0, mask);
#endif
}
+ if (data0) {
+ xcall_deliver(data0, __pa(pg_addr),
+ (u64) pg_addr, &cpu_online_map);
#ifdef CONFIG_DEBUG_DCFLUSH
- atomic_inc(&dcpage_flushes_xcall);
+ atomic_inc(&dcpage_flushes_xcall);
#endif
- flush_self:
+ }
__local_flush_dcache_page(page);
put_cpu();
}
-static void __smp_receive_signal_mask(cpumask_t mask)
-{
- smp_cross_call_masked(&xcall_receive_signal, 0, 0, 0, mask);
-}
-
-void smp_receive_signal(int cpu)
-{
- cpumask_t mask = cpumask_of_cpu(cpu);
-
- if (cpu_online(cpu))
- __smp_receive_signal_mask(mask);
-}
-
-void smp_receive_signal_client(int irq, struct pt_regs *regs)
-{
- clear_softint(1 << irq);
-}
-
void smp_new_mmu_context_version_client(int irq, struct pt_regs *regs)
{
struct mm_struct *mm;
}
#endif
-void smp_report_regs(void)
-{
- smp_cross_call(&xcall_report_regs, 0, 0, 0);
-}
-
#ifdef CONFIG_MAGIC_SYSRQ
void smp_fetch_global_regs(void)
{
smp_cross_call_masked(&xcall_flush_tlb_mm,
ctx, 0, 0,
- mm->cpu_vm_mask);
+ &mm->cpu_vm_mask);
local_flush_and_out:
__flush_tlb_mm(ctx, SECONDARY_CONTEXT);
else
smp_cross_call_masked(&xcall_flush_tlb_pending,
ctx, nr, (unsigned long) vaddrs,
- mm->cpu_vm_mask);
+ &mm->cpu_vm_mask);
__flush_tlb_pending(ctx, nr, vaddrs);
{
}
+void __init smp_setup_processor_id(void)
+{
+ if (tlb_type == spitfire)
+ xcall_deliver_impl = spitfire_xcall_deliver;
+ else if (tlb_type == cheetah || tlb_type == cheetah_plus)
+ xcall_deliver_impl = cheetah_xcall_deliver;
+ else
+ xcall_deliver_impl = hypervisor_xcall_deliver;
+}
+
void __devinit smp_fill_in_sib_core_maps(void)
{
unsigned int i;
void smp_send_reschedule(int cpu)
{
- smp_receive_signal(cpu);
+ xcall_deliver((u64) &xcall_receive_signal, 0, 0,
+ &cpumask_of_cpu(cpu));
+}
+
+void smp_receive_signal_client(int irq, struct pt_regs *regs)
+{
+ clear_softint(1 << irq);
}
/* This is a nop because we capture all other cpus
extern void *__memscan_generic(void *, int, size_t);
extern int __memcmp(const void *, const void *, __kernel_size_t);
extern __kernel_size_t strlen(const char *);
-extern void show_regs(struct pt_regs *);
extern void syscall_trace(struct pt_regs *, int);
extern void sys_sigsuspend(void);
extern int compat_sys_ioctl(unsigned int fd, unsigned int cmd, u32 arg);
/* Bogus frame pointer? */
if (fp < (thread_base + sizeof(struct thread_info)) ||
- fp >= (thread_base + THREAD_SIZE))
+ fp > (thread_base + THREAD_SIZE - sizeof(struct sparc_stackf)))
break;
sf = (struct sparc_stackf *) fp;
regs = (struct pt_regs *) (sf + 1);
- if ((regs->magic & ~0x1ff) == PT_REGS_MAGIC) {
+ if (((unsigned long)regs <=
+ (thread_base + THREAD_SIZE - sizeof(*regs))) &&
+ (regs->magic & ~0x1ff) == PT_REGS_MAGIC) {
if (!(regs->tstate & TSTATE_PRIV))
break;
pc = regs->tpc;
#include <asm/mmu_context.h>
#include <asm/compat_signal.h>
-asmlinkage long sys32_chown16(const char __user * filename, u16 user, u16 group)
-{
- return sys_chown(filename, low2highuid(user), low2highgid(group));
-}
-
-asmlinkage long sys32_lchown16(const char __user * filename, u16 user, u16 group)
-{
- return sys_lchown(filename, low2highuid(user), low2highgid(group));
-}
-
-asmlinkage long sys32_fchown16(unsigned int fd, u16 user, u16 group)
-{
- return sys_fchown(fd, low2highuid(user), low2highgid(group));
-}
-
-asmlinkage long sys32_setregid16(u16 rgid, u16 egid)
-{
- return sys_setregid(low2highgid(rgid), low2highgid(egid));
-}
-
-asmlinkage long sys32_setgid16(u16 gid)
-{
- return sys_setgid((gid_t)gid);
-}
-
-asmlinkage long sys32_setreuid16(u16 ruid, u16 euid)
-{
- return sys_setreuid(low2highuid(ruid), low2highuid(euid));
-}
-
-asmlinkage long sys32_setuid16(u16 uid)
-{
- return sys_setuid((uid_t)uid);
-}
-
-asmlinkage long sys32_setresuid16(u16 ruid, u16 euid, u16 suid)
-{
- return sys_setresuid(low2highuid(ruid), low2highuid(euid),
- low2highuid(suid));
-}
-
-asmlinkage long sys32_getresuid16(u16 __user *ruid, u16 __user *euid, u16 __user *suid)
-{
- int retval;
-
- if (!(retval = put_user(high2lowuid(current->uid), ruid)) &&
- !(retval = put_user(high2lowuid(current->euid), euid)))
- retval = put_user(high2lowuid(current->suid), suid);
-
- return retval;
-}
-
-asmlinkage long sys32_setresgid16(u16 rgid, u16 egid, u16 sgid)
-{
- return sys_setresgid(low2highgid(rgid), low2highgid(egid),
- low2highgid(sgid));
-}
-
-asmlinkage long sys32_getresgid16(u16 __user *rgid, u16 __user *egid, u16 __user *sgid)
-{
- int retval;
-
- if (!(retval = put_user(high2lowgid(current->gid), rgid)) &&
- !(retval = put_user(high2lowgid(current->egid), egid)))
- retval = put_user(high2lowgid(current->sgid), sgid);
-
- return retval;
-}
-
-asmlinkage long sys32_setfsuid16(u16 uid)
-{
- return sys_setfsuid((uid_t)uid);
-}
-
-asmlinkage long sys32_setfsgid16(u16 gid)
-{
- return sys_setfsgid((gid_t)gid);
-}
-
-static int groups16_to_user(u16 __user *grouplist, struct group_info *group_info)
-{
- int i;
- u16 group;
-
- for (i = 0; i < group_info->ngroups; i++) {
- group = (u16)GROUP_AT(group_info, i);
- if (put_user(group, grouplist+i))
- return -EFAULT;
- }
-
- return 0;
-}
-
-static int groups16_from_user(struct group_info *group_info, u16 __user *grouplist)
-{
- int i;
- u16 group;
-
- for (i = 0; i < group_info->ngroups; i++) {
- if (get_user(group, grouplist+i))
- return -EFAULT;
- GROUP_AT(group_info, i) = (gid_t)group;
- }
-
- return 0;
-}
-
-asmlinkage long sys32_getgroups16(int gidsetsize, u16 __user *grouplist)
-{
- int i;
-
- if (gidsetsize < 0)
- return -EINVAL;
-
- get_group_info(current->group_info);
- i = current->group_info->ngroups;
- if (gidsetsize) {
- if (i > gidsetsize) {
- i = -EINVAL;
- goto out;
- }
- if (groups16_to_user(grouplist, current->group_info)) {
- i = -EFAULT;
- goto out;
- }
- }
-out:
- put_group_info(current->group_info);
- return i;
-}
-
-asmlinkage long sys32_setgroups16(int gidsetsize, u16 __user *grouplist)
-{
- struct group_info *group_info;
- int retval;
-
- if (!capable(CAP_SETGID))
- return -EPERM;
- if ((unsigned)gidsetsize > NGROUPS_MAX)
- return -EINVAL;
-
- group_info = groups_alloc(gidsetsize);
- if (!group_info)
- return -ENOMEM;
- retval = groups16_from_user(group_info, grouplist);
- if (retval) {
- put_group_info(group_info);
- return retval;
- }
-
- retval = set_current_groups(group_info);
- put_group_info(group_info);
-
- return retval;
-}
-
-asmlinkage long sys32_getuid16(void)
-{
- return high2lowuid(current->uid);
-}
-
-asmlinkage long sys32_geteuid16(void)
-{
- return high2lowuid(current->euid);
-}
-
-asmlinkage long sys32_getgid16(void)
-{
- return high2lowgid(current->gid);
-}
-
-asmlinkage long sys32_getegid16(void)
-{
- return high2lowgid(current->egid);
-}
-
/* 32-bit timeval and related flotsam. */
static inline long put_tv32(struct compat_timeval __user *o, struct timeval *i)
sys_call_table32:
/*0*/ .word sys_restart_syscall, sys32_exit, sys_fork, sys_read, sys_write
/*5*/ .word sys32_open, sys_close, sys32_wait4, sys32_creat, sys_link
-/*10*/ .word sys_unlink, sunos_execv, sys_chdir, sys32_chown16, sys32_mknod
-/*15*/ .word sys_chmod, sys32_lchown16, sparc_brk, sys32_perfctr, sys32_lseek
-/*20*/ .word sys_getpid, sys_capget, sys_capset, sys32_setuid16, sys32_getuid16
+/*10*/ .word sys_unlink, sunos_execv, sys_chdir, sys_chown16, sys32_mknod
+/*15*/ .word sys_chmod, sys_lchown16, sparc_brk, sys32_perfctr, sys32_lseek
+/*20*/ .word sys_getpid, sys_capget, sys_capset, sys_setuid16, sys_getuid16
/*25*/ .word sys32_vmsplice, compat_sys_ptrace, sys_alarm, sys32_sigaltstack, sys32_pause
/*30*/ .word compat_sys_utime, sys_lchown, sys_fchown, sys32_access, sys32_nice
.word sys_chown, sys_sync, sys32_kill, compat_sys_newstat, sys32_sendfile
/*40*/ .word compat_sys_newlstat, sys_dup, sys_pipe, compat_sys_times, sys_getuid
- .word sys32_umount, sys32_setgid16, sys32_getgid16, sys32_signal, sys32_geteuid16
-/*50*/ .word sys32_getegid16, sys_acct, sys_nis_syscall, sys_getgid, compat_sys_ioctl
+ .word sys32_umount, sys_setgid16, sys_getgid16, sys32_signal, sys_geteuid16
+/*50*/ .word sys_getegid16, sys_acct, sys_nis_syscall, sys_getgid, compat_sys_ioctl
.word sys32_reboot, sys32_mmap2, sys_symlink, sys32_readlink, sys32_execve
/*60*/ .word sys32_umask, sys_chroot, compat_sys_newfstat, compat_sys_fstat64, sys_getpagesize
.word sys32_msync, sys_vfork, sys32_pread64, sys32_pwrite64, sys_geteuid
/*70*/ .word sys_getegid, sys_mmap, sys_setreuid, sys_munmap, sys_mprotect
- .word sys_madvise, sys_vhangup, sys32_truncate64, sys_mincore, sys32_getgroups16
-/*80*/ .word sys32_setgroups16, sys_getpgrp, sys32_setgroups, sys32_setitimer, sys32_ftruncate64
+ .word sys_madvise, sys_vhangup, sys32_truncate64, sys_mincore, sys_getgroups16
+/*80*/ .word sys_setgroups16, sys_getpgrp, sys32_setgroups, sys32_setitimer, sys32_ftruncate64
.word sys32_swapon, sys32_getitimer, sys_setuid, sys32_sethostname, sys_setgid
/*90*/ .word sys_dup2, sys_setfsuid, compat_sys_fcntl, sys32_select, sys_setfsgid
.word sys_fsync, sys32_setpriority, sys_nis_syscall, sys_nis_syscall, sys_nis_syscall
.word compat_sys_rt_sigtimedwait, sys32_rt_sigqueueinfo, compat_sys_rt_sigsuspend, sys_setresuid, sys_getresuid
/*110*/ .word sys_setresgid, sys_getresgid, sys_setregid, sys_nis_syscall, sys_nis_syscall
.word sys32_getgroups, sys32_gettimeofday, sys32_getrusage, sys_nis_syscall, sys_getcwd
-/*120*/ .word compat_sys_readv, compat_sys_writev, sys32_settimeofday, sys32_fchown16, sys_fchmod
- .word sys_nis_syscall, sys32_setreuid16, sys32_setregid16, sys_rename, sys_truncate
+/*120*/ .word compat_sys_readv, compat_sys_writev, sys32_settimeofday, sys_fchown16, sys_fchmod
+ .word sys_nis_syscall, sys_setreuid16, sys_setregid16, sys_rename, sys_truncate
/*130*/ .word sys_ftruncate, sys_flock, compat_sys_lstat64, sys_nis_syscall, sys_nis_syscall
.word sys_nis_syscall, sys32_mkdir, sys_rmdir, compat_sys_utimes, compat_sys_stat64
/*140*/ .word sys32_sendfile64, sys_nis_syscall, sys32_futex, sys_gettid, compat_sys_getrlimit
/*210*/ .word sys32_fadvise64_64, sys32_tgkill, sys32_waitpid, sys_swapoff, compat_sys_sysinfo
.word compat_sys_ipc, sys32_sigreturn, sys_clone, sys32_ioprio_get, compat_sys_adjtimex
/*220*/ .word sys32_sigprocmask, sys_ni_syscall, sys32_delete_module, sys_ni_syscall, sys32_getpgid
- .word sys32_bdflush, sys32_sysfs, sys_nis_syscall, sys32_setfsuid16, sys32_setfsgid16
+ .word sys32_bdflush, sys32_sysfs, sys_nis_syscall, sys_setfsuid16, sys_setfsgid16
/*230*/ .word sys32_select, compat_sys_time, sys32_splice, compat_sys_stime, compat_sys_statfs64
.word compat_sys_fstatfs64, sys_llseek, sys_mlock, sys_munlock, sys32_mlockall
/*240*/ .word sys_munlockall, sys32_sched_setparam, sys32_sched_getparam, sys32_sched_setscheduler, sys32_sched_getscheduler
#include <linux/kernel_stat.h>
#include <linux/clockchips.h>
#include <linux/clocksource.h>
+#include <linux/of_device.h>
#include <asm/oplib.h>
#include <asm/mostek.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/prom.h>
-#include <asm/of_device.h>
#include <asm/starfire.h>
#include <asm/smp.h>
#include <asm/sections.h>
pfx,
ent->err_raddr, ent->err_size, ent->err_cpu);
- __show_regs(regs);
+ show_regs(regs);
if ((cnt = atomic_read(ocnt)) != 0) {
atomic_set(ocnt, 0);
void die_if_kernel(char *str, struct pt_regs *regs)
{
static int die_counter;
- extern void smp_report_regs(void);
int count = 0;
/* Amuse the user. */
printk("%s(%d): %s [#%d]\n", current->comm, task_pid_nr(current), str, ++die_counter);
notify_die(DIE_OOPS, str, regs, 0, 255, SIGSEGV);
__asm__ __volatile__("flushw");
- __show_regs(regs);
+ show_regs(regs);
add_taint(TAINT_DIE);
if (regs->tstate & TSTATE_PRIV) {
struct reg_window *rw = (struct reg_window *)
}
user_instruction_dump ((unsigned int __user *) regs->tpc);
}
-#if 0
-#ifdef CONFIG_SMP
- smp_report_regs();
-#endif
-#endif
if (regs->tstate & TSTATE_PRIV)
do_exit(SIGKILL);
do_exit(SIGSEGV);
/* arch/sparc64/mm/tsb.c
*
- * Copyright (C) 2006 David S. Miller <davem@davemloft.net>
+ * Copyright (C) 2006, 2008 David S. Miller <davem@davemloft.net>
*/
#include <linux/kernel.h>
+#include <linux/preempt.h>
#include <asm/system.h>
#include <asm/page.h>
#include <asm/tlbflush.h>
tsb_context_switch(mm);
/* Now force other processors to do the same. */
+ preempt_disable();
smp_tsb_sync(mm);
+ preempt_enable();
/* Now it is safe to free the old tsb. */
kmem_cache_free(tsb_caches[old_cache_index], old_tsb);
b rtrap_xcall
ldx [%sp + PTREGS_OFF + PT_V9_TSTATE], %l1
- /* NOTE: This is SPECIAL!! We do etrap/rtrap however
- * we choose to deal with the "BH's run with
- * %pil==15" problem (described in asm/pil.h)
- * by just invoking rtrap directly past where
- * BH's are checked for.
- *
- * We do it like this because we do not want %pil==15
- * lockups to prevent regs being reported.
- */
- .globl xcall_report_regs
-xcall_report_regs:
-
-661: rdpr %pstate, %g2
- wrpr %g2, PSTATE_IG | PSTATE_AG, %pstate
- .section .sun4v_2insn_patch, "ax"
- .word 661b
- nop
- nop
- .previous
-
- rdpr %pil, %g2
- wrpr %g0, 15, %pil
- sethi %hi(109f), %g7
- b,pt %xcc, etrap_irq
-109: or %g7, %lo(109b), %g7
-#ifdef CONFIG_TRACE_IRQFLAGS
- call trace_hardirqs_off
- nop
-#endif
- call __show_regs
- add %sp, PTREGS_OFF, %o0
- /* Has to be a non-v9 branch due to the large distance. */
- b rtrap_xcall
- ldx [%sp + PTREGS_OFF + PT_V9_TSTATE], %l1
-
#ifdef CONFIG_MAGIC_SYSRQ
.globl xcall_fetch_glob_regs
xcall_fetch_glob_regs:
stx %g7, [%g1 + GR_SNAP_TNPC]
stx %o7, [%g1 + GR_SNAP_O7]
stx %i7, [%g1 + GR_SNAP_I7]
+ /* Don't try this at home kids... */
+ rdpr %cwp, %g2
+ sub %g2, 1, %g7
+ wrpr %g7, %cwp
+ mov %i7, %g7
+ wrpr %g2, %cwp
+ stx %g7, [%g1 + GR_SNAP_RPC]
sethi %hi(trap_block), %g7
or %g7, %lo(trap_block), %g7
sllx %g2, TRAP_BLOCK_SZ_SHIFT, %g2
if (tty == NULL)
return IRQ_NONE;
- if (test_bit(TTY_DO_WRITE_WAKEUP, &tty->flags) &&
- (tty->ldisc.write_wakeup != NULL))
- (tty->ldisc.write_wakeup)(tty);
-
- /*
- * BLOCKING mode
- * In blocking mode, everything sleeps on tty->write_wait.
- * Sleeping in the console driver would break non-blocking
- * writes.
- */
-
- if (waitqueue_active(&tty->write_wait))
- wake_up_interruptible(&tty->write_wait);
+ tty_wakeup(tty);
return IRQ_HANDLED;
}
{
return uv_system_type != UV_NONE;
}
+EXPORT_SYMBOL_GPL(is_uv_system);
pci_swiotlb_init();
}
+
+unsigned long iommu_num_pages(unsigned long addr, unsigned long len)
+{
+ unsigned long size = roundup((addr & ~PAGE_MASK) + len, PAGE_SIZE);
+
+ return size >> PAGE_SHIFT;
+}
+EXPORT_SYMBOL(iommu_num_pages);
#endif
/*
initmem_init(0, max_pfn);
-#ifdef CONFIG_X86_64
- dma32_reserve_bootmem();
-#endif
-
#ifdef CONFIG_ACPI_SLEEP
/*
* Reserve low memory region for sleep support.
#endif
reserve_crashkernel();
+#ifdef CONFIG_X86_64
+ /*
+ * dma32_reserve_bootmem() allocates bootmem which may conflict
+ * with the crashkernel command line, so do that after
+ * reserve_crashkernel()
+ */
+ dma32_reserve_bootmem();
+#endif
+
reserve_ibft_region();
#ifdef CONFIG_KVM_CLOCK
account_shadowed(kvm, gfn);
}
+static int kvm_unmap_rmapp(struct kvm *kvm, unsigned long *rmapp)
+{
+ u64 *spte;
+ int need_tlb_flush = 0;
+
+ while ((spte = rmap_next(kvm, rmapp, NULL))) {
+ BUG_ON(!(*spte & PT_PRESENT_MASK));
+ rmap_printk("kvm_rmap_unmap_hva: spte %p %llx\n", spte, *spte);
+ rmap_remove(kvm, spte);
+ set_shadow_pte(spte, shadow_trap_nonpresent_pte);
+ need_tlb_flush = 1;
+ }
+ return need_tlb_flush;
+}
+
+static int kvm_handle_hva(struct kvm *kvm, unsigned long hva,
+ int (*handler)(struct kvm *kvm, unsigned long *rmapp))
+{
+ int i;
+ int retval = 0;
+
+ /*
+ * If mmap_sem isn't taken, we can look the memslots with only
+ * the mmu_lock by skipping over the slots with userspace_addr == 0.
+ */
+ for (i = 0; i < kvm->nmemslots; i++) {
+ struct kvm_memory_slot *memslot = &kvm->memslots[i];
+ unsigned long start = memslot->userspace_addr;
+ unsigned long end;
+
+ /* mmu_lock protects userspace_addr */
+ if (!start)
+ continue;
+
+ end = start + (memslot->npages << PAGE_SHIFT);
+ if (hva >= start && hva < end) {
+ gfn_t gfn_offset = (hva - start) >> PAGE_SHIFT;
+ retval |= handler(kvm, &memslot->rmap[gfn_offset]);
+ retval |= handler(kvm,
+ &memslot->lpage_info[
+ gfn_offset /
+ KVM_PAGES_PER_HPAGE].rmap_pde);
+ }
+ }
+
+ return retval;
+}
+
+int kvm_unmap_hva(struct kvm *kvm, unsigned long hva)
+{
+ return kvm_handle_hva(kvm, hva, kvm_unmap_rmapp);
+}
+
+static int kvm_age_rmapp(struct kvm *kvm, unsigned long *rmapp)
+{
+ u64 *spte;
+ int young = 0;
+
+ spte = rmap_next(kvm, rmapp, NULL);
+ while (spte) {
+ int _young;
+ u64 _spte = *spte;
+ BUG_ON(!(_spte & PT_PRESENT_MASK));
+ _young = _spte & PT_ACCESSED_MASK;
+ if (_young) {
+ young = 1;
+ clear_bit(PT_ACCESSED_SHIFT, (unsigned long *)spte);
+ }
+ spte = rmap_next(kvm, rmapp, spte);
+ }
+ return young;
+}
+
+int kvm_age_hva(struct kvm *kvm, unsigned long hva)
+{
+ return kvm_handle_hva(kvm, hva, kvm_age_rmapp);
+}
+
#ifdef MMU_DEBUG
static int is_empty_shadow_page(u64 *spt)
{
int r;
int largepage = 0;
pfn_t pfn;
+ unsigned long mmu_seq;
down_read(¤t->mm->mmap_sem);
if (is_largepage_backed(vcpu, gfn & ~(KVM_PAGES_PER_HPAGE-1))) {
largepage = 1;
}
+ mmu_seq = vcpu->kvm->mmu_notifier_seq;
+ /* implicit mb(), we'll read before PT lock is unlocked */
pfn = gfn_to_pfn(vcpu->kvm, gfn);
up_read(¤t->mm->mmap_sem);
}
spin_lock(&vcpu->kvm->mmu_lock);
+ if (mmu_notifier_retry(vcpu, mmu_seq))
+ goto out_unlock;
kvm_mmu_free_some_pages(vcpu);
r = __direct_map(vcpu, v, write, largepage, gfn, pfn,
PT32E_ROOT_LEVEL);
return r;
+
+out_unlock:
+ spin_unlock(&vcpu->kvm->mmu_lock);
+ kvm_release_pfn_clean(pfn);
+ return 0;
}
int r;
int largepage = 0;
gfn_t gfn = gpa >> PAGE_SHIFT;
+ unsigned long mmu_seq;
ASSERT(vcpu);
ASSERT(VALID_PAGE(vcpu->arch.mmu.root_hpa));
gfn &= ~(KVM_PAGES_PER_HPAGE-1);
largepage = 1;
}
+ mmu_seq = vcpu->kvm->mmu_notifier_seq;
+ /* implicit mb(), we'll read before PT lock is unlocked */
pfn = gfn_to_pfn(vcpu->kvm, gfn);
up_read(¤t->mm->mmap_sem);
if (is_error_pfn(pfn)) {
return 1;
}
spin_lock(&vcpu->kvm->mmu_lock);
+ if (mmu_notifier_retry(vcpu, mmu_seq))
+ goto out_unlock;
kvm_mmu_free_some_pages(vcpu);
r = __direct_map(vcpu, gpa, error_code & PFERR_WRITE_MASK,
largepage, gfn, pfn, kvm_x86_ops->get_tdp_level());
spin_unlock(&vcpu->kvm->mmu_lock);
return r;
+
+out_unlock:
+ spin_unlock(&vcpu->kvm->mmu_lock);
+ kvm_release_pfn_clean(pfn);
+ return 0;
}
static void nonpaging_free(struct kvm_vcpu *vcpu)
gfn &= ~(KVM_PAGES_PER_HPAGE-1);
vcpu->arch.update_pte.largepage = 1;
}
+ vcpu->arch.update_pte.mmu_seq = vcpu->kvm->mmu_notifier_seq;
+ /* implicit mb(), we'll read before PT lock is unlocked */
pfn = gfn_to_pfn(vcpu->kvm, gfn);
up_read(¤t->mm->mmap_sem);
pfn = vcpu->arch.update_pte.pfn;
if (is_error_pfn(pfn))
return;
+ if (mmu_notifier_retry(vcpu, vcpu->arch.update_pte.mmu_seq))
+ return;
kvm_get_pfn(pfn);
mmu_set_spte(vcpu, spte, page->role.access, pte_access, 0, 0,
gpte & PT_DIRTY_MASK, NULL, largepage, gpte_to_gfn(gpte),
int r;
pfn_t pfn;
int largepage = 0;
+ unsigned long mmu_seq;
pgprintk("%s: addr %lx err %x\n", __func__, addr, error_code);
kvm_mmu_audit(vcpu, "pre page fault");
largepage = 1;
}
}
+ mmu_seq = vcpu->kvm->mmu_notifier_seq;
+ /* implicit mb(), we'll read before PT lock is unlocked */
pfn = gfn_to_pfn(vcpu->kvm, walker.gfn);
up_read(¤t->mm->mmap_sem);
}
spin_lock(&vcpu->kvm->mmu_lock);
+ if (mmu_notifier_retry(vcpu, mmu_seq))
+ goto out_unlock;
kvm_mmu_free_some_pages(vcpu);
shadow_pte = FNAME(fetch)(vcpu, addr, &walker, user_fault, write_fault,
largepage, &write_pt, pfn);
spin_unlock(&vcpu->kvm->mmu_lock);
return write_pt;
+
+out_unlock:
+ spin_unlock(&vcpu->kvm->mmu_lock);
+ kvm_release_pfn_clean(pfn);
+ return 0;
}
static gpa_t FNAME(gva_to_gpa)(struct kvm_vcpu *vcpu, gva_t vaddr)
case KVM_CAP_PIT:
case KVM_CAP_NOP_IO_DELAY:
case KVM_CAP_MP_STATE:
+ case KVM_CAP_SYNC_MMU:
r = 1;
break;
case KVM_CAP_COALESCED_MMIO:
goto out;
down_write(&kvm->slots_lock);
+ spin_lock(&kvm->mmu_lock);
p = &kvm->arch.aliases[alias->slot];
p->base_gfn = alias->guest_phys_addr >> PAGE_SHIFT;
break;
kvm->arch.naliases = n;
+ spin_unlock(&kvm->mmu_lock);
kvm_mmu_zap_all(kvm);
up_write(&kvm->slots_lock);
*/
if (!user_alloc) {
if (npages && !old.rmap) {
+ unsigned long userspace_addr;
+
down_write(¤t->mm->mmap_sem);
- memslot->userspace_addr = do_mmap(NULL, 0,
- npages * PAGE_SIZE,
- PROT_READ | PROT_WRITE,
- MAP_SHARED | MAP_ANONYMOUS,
- 0);
+ userspace_addr = do_mmap(NULL, 0,
+ npages * PAGE_SIZE,
+ PROT_READ | PROT_WRITE,
+ MAP_SHARED | MAP_ANONYMOUS,
+ 0);
up_write(¤t->mm->mmap_sem);
- if (IS_ERR((void *)memslot->userspace_addr))
- return PTR_ERR((void *)memslot->userspace_addr);
+ if (IS_ERR((void *)userspace_addr))
+ return PTR_ERR((void *)userspace_addr);
+
+ /* set userspace_addr atomically for kvm_hva_to_rmapp */
+ spin_lock(&kvm->mmu_lock);
+ memslot->userspace_addr = userspace_addr;
+ spin_unlock(&kvm->mmu_lock);
} else {
if (!old.user_alloc && old.rmap) {
int ret;
jnz 100b
102:
.section .fixup,"ax"
-103: addl %r8d,%edx /* ecx is zerorest also */
+103: addl %ecx,%edx /* ecx is zerorest also */
jmp copy_user_handle_tail
.previous
jnz 100b
102:
.section .fixup,"ax"
-103: addl %r8d,%edx /* ecx is zerorest also */
+103: addl %ecx,%edx /* ecx is zerorest also */
jmp copy_user_handle_tail
.previous
jmp 60f
50: movl %ecx,%edx
60: sfence
- movl %r8d,%ecx
jmp copy_user_handle_tail
.previous
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <linux/in6.h>
-#include <linux/ide.h>
#include <asm/uaccess.h>
#include <asm/checksum.h>
}
EXPORT_SYMBOL(blk_plug_device);
+/**
+ * blk_plug_device_unlocked - plug a device without queue lock held
+ * @q: The &struct request_queue to plug
+ *
+ * Description:
+ * Like @blk_plug_device(), but grabs the queue lock and disables
+ * interrupts.
+ **/
+void blk_plug_device_unlocked(struct request_queue *q)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(q->queue_lock, flags);
+ blk_plug_device(q);
+ spin_unlock_irqrestore(q->queue_lock, flags);
+}
+EXPORT_SYMBOL(blk_plug_device_unlocked);
+
/*
* remove the queue from the plugged list, if present. called with
* queue lock held and interrupts disabled.
hdr.sbp = cgc.sense;
if (hdr.sbp)
hdr.mx_sb_len = sizeof(struct request_sense);
- hdr.timeout = cgc.timeout;
+ hdr.timeout = jiffies_to_msecs(cgc.timeout);
hdr.cmdp = ((struct cdrom_generic_command __user*) arg)->cmd;
hdr.cmd_len = sizeof(cgc.cmd);
if (unlikely(!tx)) {
async_tx_quiesce(&depend_tx);
- while (!tx)
+ while (!tx) {
dma_async_issue_pending(chan);
tx = device->device_prep_dma_zero_sum(chan,
dma_src, src_cnt, len, result,
dma_prep_flags);
+ }
}
async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_VIRTIO) += virtio/
+obj-$(CONFIG_REGULATOR) += regulator/
static uid_t asus_uid;
static gid_t asus_gid;
module_param(asus_uid, uint, 0);
-MODULE_PARM_DESC(asus_uid, "UID for entries in /proc/acpi/asus.\n");
+MODULE_PARM_DESC(asus_uid, "UID for entries in /proc/acpi/asus");
module_param(asus_gid, uint, 0);
-MODULE_PARM_DESC(asus_gid, "GID for entries in /proc/acpi/asus.\n");
+MODULE_PARM_DESC(asus_gid, "GID for entries in /proc/acpi/asus");
/* For each model, all features implemented,
* those marked with R are relative to HOTK, A for absolute */
* policy is adjusted accordingly.
*/
-static unsigned int ignore_ppc = 0;
+/* ignore_ppc:
+ * -1 -> cpufreq low level drivers not initialized -> _PSS, etc. not called yet
+ * ignore _PPC
+ * 0 -> cpufreq low level drivers initialized -> consider _PPC values
+ * 1 -> ignore _PPC totally -> forced by user through boot param
+ */
+static unsigned int ignore_ppc = -1;
module_param(ignore_ppc, uint, 0644);
MODULE_PARM_DESC(ignore_ppc, "If the frequency of your machine gets wrongly" \
"limited by BIOS, this should help");
#define PPC_REGISTERED 1
#define PPC_IN_USE 2
-static int acpi_processor_ppc_status = 0;
+static int acpi_processor_ppc_status;
static int acpi_processor_ppc_notifier(struct notifier_block *nb,
unsigned long event, void *data)
struct acpi_processor *pr;
unsigned int ppc = 0;
- if (ignore_ppc)
+ if (event == CPUFREQ_START && ignore_ppc <= 0) {
+ ignore_ppc = 0;
return 0;
+ }
- mutex_lock(&performance_mutex);
+ if (ignore_ppc)
+ return 0;
if (event != CPUFREQ_INCOMPATIBLE)
- goto out;
+ return 0;
+
+ mutex_lock(&performance_mutex);
pr = per_cpu(processors, policy->cpu);
if (!pr || !pr->performance)
/* Mobile SATA Controller IDE (ICH8M), Apple */
{ 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata },
{ 0x8086, 0x2828, 0x106b, 0x00a1, 0, 0, ich8m_apple_sata },
+ { 0x8086, 0x2828, 0x106b, 0x00a3, 0, 0, ich8m_apple_sata },
/* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata },
/* SATA Controller IDE (ICH9) */
module_param_string(force, ata_force_param_buf, sizeof(ata_force_param_buf), 0);
MODULE_PARM_DESC(force, "Force ATA configurations including cable type, link speed and transfer mode (see Documentation/kernel-parameters.txt for details)");
-int atapi_enabled = 1;
+static int atapi_enabled = 1;
module_param(atapi_enabled, int, 0444);
MODULE_PARM_DESC(atapi_enabled, "Enable discovery of ATAPI devices (0=off, 1=on)");
{
unsigned int c;
+ BUG_ON(len & 1);
+
while (len > 0) {
c = id[ofs] >> 8;
*s = c;
{
unsigned char *p;
- WARN_ON(!(len & 1));
-
ata_id_string(id, s, ofs, len - 1);
p = s + strnlen(s, len - 1);
return 3 << ATA_SHIFT_PIO;
}
+/**
+ * ata_do_dev_read_id - default ID read method
+ * @dev: device
+ * @tf: proposed taskfile
+ * @id: data buffer
+ *
+ * Issue the identify taskfile and hand back the buffer containing
+ * identify data. For some RAID controllers and for pre ATA devices
+ * this function is wrapped or replaced by the driver
+ */
+unsigned int ata_do_dev_read_id(struct ata_device *dev,
+ struct ata_taskfile *tf, u16 *id)
+{
+ return ata_exec_internal(dev, tf, NULL, DMA_FROM_DEVICE,
+ id, sizeof(id[0]) * ATA_ID_WORDS, 0);
+}
+
/**
* ata_dev_read_id - Read ID data from the specified device
* @dev: target device
if (ata_msg_ctl(ap))
ata_dev_printk(dev, KERN_DEBUG, "%s: ENTER\n", __func__);
- retry:
+retry:
ata_tf_init(dev, &tf);
switch (class) {
*/
tf.flags |= ATA_TFLAG_POLLING;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
- id, sizeof(id[0]) * ATA_ID_WORDS, 0);
+ if (ap->ops->read_id)
+ err_mask = ap->ops->read_id(dev, &tf, id);
+ else
+ err_mask = ata_do_dev_read_id(dev, &tf, id);
+
if (err_mask) {
if (err_mask & AC_ERR_NODEV_HINT) {
ata_dev_printk(dev, KERN_DEBUG,
return 0;
}
+ if ((!atapi_enabled || (ap->flags & ATA_FLAG_NO_ATAPI)) &&
+ dev->class == ATA_DEV_ATAPI) {
+ ata_dev_printk(dev, KERN_WARNING,
+ "WARNING: ATAPI is %s, device ignored.\n",
+ atapi_enabled ? "not supported with this driver"
+ : "disabled");
+ ata_dev_disable(dev);
+ return 0;
+ }
+
/* let ACPI work its magic */
rc = ata_acpi_on_devcfg(dev);
if (rc)
ata_wq = create_workqueue("ata");
if (!ata_wq)
- return -ENOMEM;
+ goto free_force_tbl;
ata_aux_wq = create_singlethread_workqueue("ata_aux");
- if (!ata_aux_wq) {
- destroy_workqueue(ata_wq);
- return -ENOMEM;
- }
+ if (!ata_aux_wq)
+ goto free_wq;
printk(KERN_DEBUG "libata version " DRV_VERSION " loaded.\n");
return 0;
+
+free_wq:
+ destroy_workqueue(ata_wq);
+free_force_tbl:
+ kfree(ata_force_tbl);
+ return -ENOMEM;
}
static void __exit ata_exit(void)
#endif /* CONFIG_PM */
EXPORT_SYMBOL_GPL(ata_id_string);
EXPORT_SYMBOL_GPL(ata_id_c_string);
+EXPORT_SYMBOL_GPL(ata_do_dev_read_id);
EXPORT_SYMBOL_GPL(ata_scsi_simulate);
EXPORT_SYMBOL_GPL(ata_pio_need_iordy);
return ata_find_dev(ap, devno);
}
-/**
- * ata_scsi_dev_enabled - determine if device is enabled
- * @dev: ATA device
- *
- * Determine if commands should be sent to the specified device.
- *
- * LOCKING:
- * spin_lock_irqsave(host lock)
- *
- * RETURNS:
- * 0 if commands are not allowed / 1 if commands are allowed
- */
-
-static int ata_scsi_dev_enabled(struct ata_device *dev)
-{
- if (unlikely(!ata_dev_enabled(dev)))
- return 0;
-
- if (!atapi_enabled || (dev->link->ap->flags & ATA_FLAG_NO_ATAPI)) {
- if (unlikely(dev->class == ATA_DEV_ATAPI)) {
- ata_dev_printk(dev, KERN_WARNING,
- "WARNING: ATAPI is %s, device ignored.\n",
- atapi_enabled ? "not supported with this driver" : "disabled");
- return 0;
- }
- }
-
- return 1;
-}
-
/**
* ata_scsi_find_dev - lookup ata_device from scsi_cmnd
* @ap: ATA port to which the device is attached
{
struct ata_device *dev = __ata_scsi_find_dev(ap, scsidev);
- if (unlikely(!dev || !ata_scsi_dev_enabled(dev)))
+ if (unlikely(!dev || !ata_dev_enabled(dev)))
return NULL;
return dev;
ata_scsi_dump_cdb(ap, cmd);
- if (likely(ata_scsi_dev_enabled(ap->link.device)))
+ if (likely(ata_dev_enabled(ap->link.device)))
rc = __ata_scsi_queuecmd(cmd, done, ap->link.device);
else {
cmd->result = (DID_BAD_TARGET << 16);
extern unsigned int ata_print_id;
extern struct workqueue_struct *ata_aux_wq;
-extern int atapi_enabled;
extern int atapi_passthru16;
extern int libata_fua;
extern int libata_noacpi;
pci_read_config_byte(isa_bridge, 0x5E, &tmp);
if ((tmp & 0x1E) == 0x12)
ppi[0] = &info_20_udma;
- pci_dev_put(isa_bridge);
}
+ pci_dev_put(isa_bridge);
+
return ata_pci_sff_init_one(pdev, ppi, &ali_sht, NULL);
}
#include <linux/err.h>
#include <linux/io.h>
-#include <asm/arch/board.h>
-#include <asm/arch/smc.h>
+#include <mach/board.h>
+#include <mach/smc.h>
#define DRV_NAME "pata_at32"
#define DRV_VERSION "0.0.3"
#define DRV_NAME "pata_it821x"
-#define DRV_VERSION "0.3.8"
+#define DRV_VERSION "0.4.0"
struct it821x_dev
{
case ATA_CMD_WRITE_MULTI:
case ATA_CMD_WRITE_MULTI_EXT:
case ATA_CMD_ID_ATA:
+ case ATA_CMD_INIT_DEV_PARAMS:
+ case 0xFC: /* Internal 'report rebuild state' */
/* Arguably should just no-op this one */
case ATA_CMD_SET_FEATURES:
return ata_sff_qc_issue(qc);
if (strstr(model_num, "Integrated Technology Express")) {
/* RAID mode */
- printk(KERN_INFO "IT821x %sRAID%d volume",
+ ata_dev_printk(adev, KERN_INFO, "%sRAID%d volume",
adev->id[147]?"Bootable ":"",
adev->id[129]);
if (adev->id[129] != 1)
/* This is a controller firmware triggered funny, don't
report the drive faulty! */
adev->horkage &= ~ATA_HORKAGE_DIAGNOSTIC;
+ /* No HPA in 'smart' mode */
+ adev->horkage |= ATA_HORKAGE_BROKEN_HPA;
}
/**
- * it821x_ident_hack - Hack identify data up
- * @ap: Port
+ * it821x_read_id - Hack identify data up
+ * @adev: device to read
+ * @tf: proposed taskfile
+ * @id: buffer for returned ident data
*
- * Walk the devices on this firmware driven port and slightly
+ * Query the devices on this firmware driven port and slightly
* mash the identify data to stop us and common tools trying to
* use features not firmware supported. The firmware itself does
* some masking (eg SMART) but not enough.
- *
- * This is a bit of an abuse of the cable method, but it is the
- * only method called at the right time. We could modify the libata
- * core specifically for ident hacking but while we have one offender
- * it seems better to keep the fallout localised.
*/
-static int it821x_ident_hack(struct ata_port *ap)
+static unsigned int it821x_read_id(struct ata_device *adev,
+ struct ata_taskfile *tf, u16 *id)
{
- struct ata_device *adev;
- ata_link_for_each_dev(adev, &ap->link) {
- if (ata_dev_enabled(adev)) {
- adev->id[84] &= ~(1 << 6); /* No FUA */
- adev->id[85] &= ~(1 << 10); /* No HPA */
- adev->id[76] = 0; /* No NCQ/AN etc */
- }
+ unsigned int err_mask;
+ unsigned char model_num[ATA_ID_PROD_LEN + 1];
+
+ err_mask = ata_do_dev_read_id(adev, tf, id);
+ if (err_mask)
+ return err_mask;
+ ata_id_c_string(id, model_num, ATA_ID_PROD, sizeof(model_num));
+
+ id[83] &= ~(1 << 12); /* Cache flush is firmware handled */
+ id[83] &= ~(1 << 13); /* Ditto for LBA48 flushes */
+ id[84] &= ~(1 << 6); /* No FUA */
+ id[85] &= ~(1 << 10); /* No HPA */
+ id[76] = 0; /* No NCQ/AN etc */
+
+ if (strstr(model_num, "Integrated Technology Express")) {
+ /* Set feature bits the firmware neglects */
+ id[49] |= 0x0300; /* LBA, DMA */
+ id[82] |= 0x0400; /* LBA48 */
+ id[83] &= 0x7FFF;
+ id[83] |= 0x4000; /* Word 83 is valid */
+ id[86] |= 0x0400; /* LBA48 on */
+ id[ATA_ID_MAJOR_VER] |= 0x1F;
}
- return ata_cable_unknown(ap);
+ return err_mask;
}
-
/**
* it821x_check_atapi_dma - ATAPI DMA handler
* @qc: Command we are about to issue
return 0;
}
+/**
+ * it821x_display_disk - display disk setup
+ * @n: Device number
+ * @buf: Buffer block from firmware
+ *
+ * Produce a nice informative display of the device setup as provided
+ * by the firmware.
+ */
+
+static void it821x_display_disk(int n, u8 *buf)
+{
+ unsigned char id[41];
+ int mode = 0;
+ char *mtype;
+ char mbuf[8];
+ char *cbl = "(40 wire cable)";
+
+ static const char *types[5] = {
+ "RAID0", "RAID1" "RAID 0+1", "JBOD", "DISK"
+ };
+
+ if (buf[52] > 4) /* No Disk */
+ return;
+
+ ata_id_c_string((u16 *)buf, id, 0, 41);
+
+ if (buf[51]) {
+ mode = ffs(buf[51]);
+ mtype = "UDMA";
+ } else if (buf[49]) {
+ mode = ffs(buf[49]);
+ mtype = "MWDMA";
+ }
+
+ if (buf[76])
+ cbl = "";
+
+ if (mode)
+ snprintf(mbuf, 8, "%5s%d", mtype, mode - 1);
+ else
+ strcpy(mbuf, "PIO");
+ if (buf[52] == 4)
+ printk(KERN_INFO "%d: %-6s %-8s %s %s\n",
+ n, mbuf, types[buf[52]], id, cbl);
+ else
+ printk(KERN_INFO "%d: %-6s %-8s Volume: %1d %s %s\n",
+ n, mbuf, types[buf[52]], buf[53], id, cbl);
+ if (buf[125] < 100)
+ printk(KERN_INFO "%d: Rebuilding: %d%%\n", n, buf[125]);
+}
+
+/**
+ * it821x_firmware_command - issue firmware command
+ * @ap: IT821x port to interrogate
+ * @cmd: command
+ * @len: length
+ *
+ * Issue firmware commands expecting data back from the controller. We
+ * use this to issue commands that do not go via the normal paths. Other
+ * commands such as 0xFC can be issued normally.
+ */
+
+static u8 *it821x_firmware_command(struct ata_port *ap, u8 cmd, int len)
+{
+ u8 status;
+ int n = 0;
+ u16 *buf = kmalloc(len, GFP_KERNEL);
+ if (buf == NULL) {
+ printk(KERN_ERR "it821x_firmware_command: Out of memory\n");
+ return NULL;
+ }
+ /* This isn't quite a normal ATA command as we are talking to the
+ firmware not the drives */
+ ap->ctl |= ATA_NIEN;
+ iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
+ ata_wait_idle(ap);
+ iowrite8(ATA_DEVICE_OBS, ap->ioaddr.device_addr);
+ iowrite8(cmd, ap->ioaddr.command_addr);
+ udelay(1);
+ /* This should be almost immediate but a little paranoia goes a long
+ way. */
+ while(n++ < 10) {
+ status = ioread8(ap->ioaddr.status_addr);
+ if (status & ATA_ERR) {
+ kfree(buf);
+ printk(KERN_ERR "it821x_firmware_command: rejected\n");
+ return NULL;
+ }
+ if (status & ATA_DRQ) {
+ ioread16_rep(ap->ioaddr.data_addr, buf, len/2);
+ return (u8 *)buf;
+ }
+ mdelay(1);
+ }
+ kfree(buf);
+ printk(KERN_ERR "it821x_firmware_command: timeout\n");
+ return NULL;
+}
+
+/**
+ * it821x_probe_firmware - firmware reporting/setup
+ * @ap: IT821x port being probed
+ *
+ * Probe the firmware of the controller by issuing firmware command
+ * 0xFA and analysing the returned data.
+ */
+
+static void it821x_probe_firmware(struct ata_port *ap)
+{
+ u8 *buf;
+ int i;
+
+ /* This is a bit ugly as we can't just issue a task file to a device
+ as this is controller magic */
+
+ buf = it821x_firmware_command(ap, 0xFA, 512);
+
+ if (buf != NULL) {
+ printk(KERN_INFO "pata_it821x: Firmware %02X/%02X/%02X%02X\n",
+ buf[505],
+ buf[506],
+ buf[507],
+ buf[508]);
+ for (i = 0; i < 4; i++)
+ it821x_display_disk(i, buf + 128 * i);
+ kfree(buf);
+ }
+}
+
+
/**
* it821x_port_start - port setup
/* Long I/O's although allowed in LBA48 space cause the
onboard firmware to enter the twighlight zone */
/* No ATAPI DMA in this mode either */
+ if (ap->port_no == 0)
+ it821x_probe_firmware(ap);
}
/* Pull the current clocks from 0x50 */
if (conf & (1 << (1 + ap->port_no)))
return 0;
}
+/**
+ * it821x_rdc_cable - Cable detect for RDC1010
+ * @ap: port we are checking
+ *
+ * Return the RDC1010 cable type. Unlike the IT821x we know how to do
+ * this and can do host side cable detect
+ */
+
+static int it821x_rdc_cable(struct ata_port *ap)
+{
+ u16 r40;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ pci_read_config_word(pdev, 0x40, &r40);
+ if (r40 & (1 << (2 + ap->port_no)))
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
+}
+
static struct scsi_host_template it821x_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
.check_atapi_dma= it821x_check_atapi_dma,
.qc_issue = it821x_smart_qc_issue,
- .cable_detect = it821x_ident_hack,
+ .cable_detect = ata_cable_80wire,
.set_mode = it821x_smart_set_mode,
.dev_config = it821x_dev_config,
+ .read_id = it821x_read_id,
.port_start = it821x_port_start,
};
.port_start = it821x_port_start,
};
+static struct ata_port_operations it821x_rdc_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+
+ .check_atapi_dma= it821x_check_atapi_dma,
+ .sff_dev_select = it821x_passthru_dev_select,
+ .bmdma_start = it821x_passthru_bmdma_start,
+ .bmdma_stop = it821x_passthru_bmdma_stop,
+ .qc_issue = it821x_passthru_qc_issue,
+
+ .cable_detect = it821x_rdc_cable,
+ .set_piomode = it821x_passthru_set_piomode,
+ .set_dmamode = it821x_passthru_set_dmamode,
+
+ .port_start = it821x_port_start,
+};
+
static void it821x_disable_raid(struct pci_dev *pdev)
{
+ /* Neither the RDC nor the IT8211 */
+ if (pdev->vendor != PCI_VENDOR_ID_ITE ||
+ pdev->device != PCI_DEVICE_ID_ITE_8212)
+ return;
+
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(pdev, 0x5E, 0x01);
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
+ .udma_mask = ATA_UDMA6,
.port_ops = &it821x_smart_port_ops
};
static const struct ata_port_info info_passthru = {
.udma_mask = ATA_UDMA6,
.port_ops = &it821x_passthru_port_ops
};
+ static const struct ata_port_info info_rdc = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = 0x1f,
+ .mwdma_mask = 0x07,
+ /* No UDMA */
+ .port_ops = &it821x_rdc_port_ops
+ };
const struct ata_port_info *ppi[] = { NULL, NULL };
static char *mode[2] = { "pass through", "smart" };
rc = pcim_enable_device(pdev);
if (rc)
return rc;
+
+ if (pdev->vendor == PCI_VENDOR_ID_RDC) {
+ ppi[0] = &info_rdc;
+ } else {
+ /* Force the card into bypass mode if so requested */
+ if (it8212_noraid) {
+ printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
+ it821x_disable_raid(pdev);
+ }
+ pci_read_config_byte(pdev, 0x50, &conf);
+ conf &= 1;
- /* Force the card into bypass mode if so requested */
- if (it8212_noraid) {
- printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n");
- it821x_disable_raid(pdev);
+ printk(KERN_INFO DRV_NAME": controller in %s mode.\n",
+ mode[conf]);
+ if (conf == 0)
+ ppi[0] = &info_passthru;
+ else
+ ppi[0] = &info_smart;
}
- pci_read_config_byte(pdev, 0x50, &conf);
- conf &= 1;
-
- printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]);
- if (conf == 0)
- ppi[0] = &info_passthru;
- else
- ppi[0] = &info_smart;
-
return ata_pci_sff_init_one(pdev, ppi, &it821x_sht, NULL);
}
static const struct pci_device_id it821x[] = {
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), },
{ PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), },
+ { PCI_VDEVICE(RDC, 0x1010), },
{ },
};
u8 rev_max;
u16 flags;
} via_isa_bridges[] = {
- { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 |
+ VIA_BAD_AST | VIA_SATA_PATA },
{ "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]);
}
+/**
+ * via_ata_sff_tf_load - send taskfile registers to host controller
+ * @ap: Port to which output is sent
+ * @tf: ATA taskfile register set
+ *
+ * Outputs ATA taskfile to standard ATA host controller.
+ *
+ * Note: This is to fix the internal bug of via chipsets, which
+ * will reset the device register after changing the IEN bit on
+ * ctl register
+ */
+static void via_ata_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ iowrite8(tf->ctl, ioaddr->ctl_addr);
+ iowrite8(tf->device, ioaddr->device_addr);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ iowrite8(tf->hob_feature, ioaddr->feature_addr);
+ iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
+ iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
+ iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
+ iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ if (is_addr) {
+ iowrite8(tf->feature, ioaddr->feature_addr);
+ iowrite8(tf->nsect, ioaddr->nsect_addr);
+ iowrite8(tf->lbal, ioaddr->lbal_addr);
+ iowrite8(tf->lbam, ioaddr->lbam_addr);
+ iowrite8(tf->lbah, ioaddr->lbah_addr);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ iowrite8(tf->device, ioaddr->device_addr);
+ VPRINTK("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
static struct scsi_host_template via_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.prereset = via_pre_reset,
+ .sff_tf_load = via_ata_tf_load,
};
static struct ata_port_operations via_port_ops_noirq = {
.inherits = &via_port_ops,
.sff_data_xfer = ata_sff_data_xfer_noirq,
+ .sff_tf_load = via_ata_tf_load,
};
/**
}
iavcc_r->vc_desc_cnt--;
dev->desc_tbl[desc1 -1].timestamp = 0;
- IF_EVENT(printk("ia_hack: return_q skb = 0x%x desc = %d\n",
- (u32)dev->desc_tbl[desc1 -1].txskb, desc1);)
+ IF_EVENT(printk("ia_hack: return_q skb = 0x%p desc = %d\n",
+ dev->desc_tbl[desc1 -1].txskb, desc1);)
if (iavcc_r->pcr < dev->rate_limit) {
IA_SKB_STATE (dev->desc_tbl[desc1-1].txskb) |= IA_TX_DONE;
if (ia_enque_rtn_q(&dev->tx_return_q, dev->desc_tbl[desc1 -1]) < 0)
inc = 0;
testSlot = idealSlot;
TstSchedTbl = (u16*)(SchedTbl+testSlot); //set index and read in value
- IF_CBR(printk("CBR Testslot 0x%x AT Location 0x%x, NumToAssign=%d\n",
- testSlot, (u32)TstSchedTbl,toBeAssigned);)
+ IF_CBR(printk("CBR Testslot 0x%x AT Location 0x%p, NumToAssign=%d\n",
+ testSlot, TstSchedTbl,toBeAssigned);)
memcpy((caddr_t)&cbrVC,(caddr_t)TstSchedTbl,sizeof(cbrVC));
while (cbrVC) // If another VC at this location, we have to keep looking
{
testSlot = idealSlot - inc;
if (testSlot < 0) { // Wrap if necessary
testSlot += dev->CbrTotEntries;
- IF_CBR(printk("Testslot Wrap. STable Start=0x%x,Testslot=%d\n",
- (u32)SchedTbl,testSlot);)
+ IF_CBR(printk("Testslot Wrap. STable Start=0x%p,Testslot=%d\n",
+ SchedTbl,testSlot);)
}
TstSchedTbl = (u16 *)(SchedTbl + testSlot); // set table index
memcpy((caddr_t)&cbrVC,(caddr_t)TstSchedTbl,sizeof(cbrVC));
}
// set table index and read in value
TstSchedTbl = (u16*)(SchedTbl + testSlot);
- IF_CBR(printk("Reading CBR Tbl from 0x%x, CbrVal=0x%x Iteration %d\n",
- (u32)TstSchedTbl,cbrVC,inc);)
+ IF_CBR(printk("Reading CBR Tbl from 0x%p, CbrVal=0x%x Iteration %d\n",
+ TstSchedTbl,cbrVC,inc);)
memcpy((caddr_t)&cbrVC,(caddr_t)TstSchedTbl,sizeof(cbrVC));
} /* while */
// Move this VCI number into this location of the CBR Sched table.
/* We know this is 32bit bus addressed so the following is safe */
writel(iadev->rx_dle_dma & 0xfffff000,
iadev->dma + IPHASE5575_RX_LIST_ADDR);
- IF_INIT(printk("Tx Dle list addr: 0x%08x value: 0x%0x\n",
- (u32)(iadev->dma+IPHASE5575_TX_LIST_ADDR),
+ IF_INIT(printk("Tx Dle list addr: 0x%p value: 0x%0x\n",
+ iadev->dma+IPHASE5575_TX_LIST_ADDR,
*(u32*)(iadev->dma+IPHASE5575_TX_LIST_ADDR));
- printk("Rx Dle list addr: 0x%08x value: 0x%0x\n",
- (u32)(iadev->dma+IPHASE5575_RX_LIST_ADDR),
+ printk("Rx Dle list addr: 0x%p value: 0x%0x\n",
+ iadev->dma+IPHASE5575_RX_LIST_ADDR,
*(u32*)(iadev->dma+IPHASE5575_RX_LIST_ADDR));)
writew(0xffff, iadev->reass_reg+REASS_MASK_REG);
buf_desc_ptr++;
rx_pkt_start += iadev->rx_buf_sz;
}
- IF_INIT(printk("Rx Buffer desc ptr: 0x%0x\n", (u32)(buf_desc_ptr));)
+ IF_INIT(printk("Rx Buffer desc ptr: 0x%p\n", buf_desc_ptr);)
i = FREE_BUF_DESC_Q*iadev->memSize;
writew(i >> 16, iadev->reass_reg+REASS_QUEUE_BASE);
writew(i, iadev->reass_reg+FREEQ_ST_ADR);
*freeq_start = (u_short)i;
freeq_start++;
}
- IF_INIT(printk("freeq_start: 0x%0x\n", (u32)freeq_start);)
+ IF_INIT(printk("freeq_start: 0x%p\n", freeq_start);)
/* Packet Complete Queue */
i = (PKT_COMP_Q * iadev->memSize) & 0xffff;
writew(i, iadev->reass_reg+PCQ_ST_ADR);
IA_SKB_STATE(skb) |= IA_DLED;
skb_queue_tail(&iavcc->txing_skb, skb);
}
- IF_EVENT(printk("tx_dle_intr: enque skb = 0x%x \n", (u32)skb);)
+ IF_EVENT(printk("tx_dle_intr: enque skb = 0x%p \n", skb);)
if (++dle == iadev->tx_dle_q.end)
dle = iadev->tx_dle_q.start;
}
writew(tmp16, iadev->seg_reg+CBR_TAB_END+1); // CBR_PTR;
tmp16 = (CBR_SCHED_TABLE*iadev->memSize + iadev->num_vc*6 - 2) >> 1;
writew(tmp16, iadev->seg_reg+CBR_TAB_END);
- IF_INIT(printk("iadev->seg_reg = 0x%x CBR_PTR_BASE = 0x%x\n",
- (u32)iadev->seg_reg, readw(iadev->seg_reg+CBR_PTR_BASE));)
+ IF_INIT(printk("iadev->seg_reg = 0x%p CBR_PTR_BASE = 0x%x\n",
+ iadev->seg_reg, readw(iadev->seg_reg+CBR_PTR_BASE));)
IF_INIT(printk("CBR_TAB_BEG = 0x%x, CBR_TAB_END = 0x%x, CBR_PTR = 0x%x\n",
readw(iadev->seg_reg+CBR_TAB_BEG), readw(iadev->seg_reg+CBR_TAB_END),
readw(iadev->seg_reg+CBR_TAB_END+1));)
/* Put the packet in a tx buffer */
trailer = iadev->tx_buf[desc-1].cpcs;
- IF_TX(printk("Sent: skb = 0x%x skb->data: 0x%x len: %d, desc: %d\n",
- (u32)skb, (u32)skb->data, skb->len, desc);)
+ IF_TX(printk("Sent: skb = 0x%p skb->data: 0x%p len: %d, desc: %d\n",
+ skb, skb->data, skb->len, desc);)
trailer->control = 0;
/*big endian*/
trailer->length = ((skb->len & 0xff) << 8) | ((skb->len & 0xff00) >> 8);
}
dev->dev_data = iadev;
IF_INIT(printk(DEV_LABEL "registered at (itf :%d)\n", dev->number);)
- IF_INIT(printk("dev_id = 0x%x iadev->LineRate = %d \n", (u32)dev,
+ IF_INIT(printk("dev_id = 0x%p iadev->LineRate = %d \n", dev,
iadev->LineRate);)
pci_set_drvdata(pdev, dev);
* class_create - create a struct class structure
* @owner: pointer to the module that is to "own" this struct class
* @name: pointer to a string for the name of this class.
+ * @key: the lock_class_key for this class; used by mutex lock debugging
*
* This is used to create a struct class pointer that can then be used
* in calls to device_create().
static char aoe_iflist[IFLISTSZ];
module_param_string(aoe_iflist, aoe_iflist, IFLISTSZ, 0600);
-MODULE_PARM_DESC(aoe_iflist, "aoe_iflist=\"dev1 [dev2 ...]\"\n");
+MODULE_PARM_DESC(aoe_iflist, "aoe_iflist=\"dev1 [dev2 ...]\"");
#ifndef MODULE
static int __init aoe_iflist_setup(char *str)
static int cciss_getgeo(struct block_device *bdev, struct hd_geometry *geo);
static int cciss_revalidate(struct gendisk *disk);
-static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk);
+static int rebuild_lun_table(ctlr_info_t *h, int first_time);
static int deregister_disk(struct gendisk *disk, drive_info_struct *drv,
int clear_all);
int withirq, sector_t total_size,
unsigned int block_size, InquiryData_struct *inq_buff,
drive_info_struct *drv);
-static void cciss_getgeometry(int cntl_num);
static void __devinit cciss_interrupt_mode(ctlr_info_t *, struct pci_dev *,
__u32);
static void start_io(ctlr_info_t *h);
return 0;
}
+ case CCISS_DEREGDISK:
+ case CCISS_REGNEWD:
case CCISS_REVALIDVOLS:
- return rebuild_lun_table(host, NULL);
+ return rebuild_lun_table(host, 0);
case CCISS_GETLUNINFO:{
LogvolInfo_struct luninfo;
return -EFAULT;
return 0;
}
- case CCISS_DEREGDISK:
- return rebuild_lun_table(host, disk);
-
- case CCISS_REGNEWD:
- return rebuild_lun_table(host, NULL);
-
case CCISS_PASSTHRU:
{
IOCTL_Command_struct iocommand;
if (ioc->Request.Type.Direction == XFER_WRITE) {
if (copy_from_user
(buff[sg_used], data_ptr, sz)) {
- status = -ENOMEM;
+ status = -EFAULT;
goto cleanup1;
}
} else {
h->next_to_run = curr_queue;
break;
}
- } else {
- curr_queue = (curr_queue + 1) % (h->highest_lun + 1);
}
}
}
spin_unlock_irqrestore(&h->lock, flags);
}
+/* This function gets the serial number of a logical drive via
+ * inquiry page 0x83. Serial no. is 16 bytes. If the serial
+ * number cannot be had, for whatever reason, 16 bytes of 0xff
+ * are returned instead.
+ */
+static void cciss_get_serial_no(int ctlr, int logvol, int withirq,
+ unsigned char *serial_no, int buflen)
+{
+#define PAGE_83_INQ_BYTES 64
+ int rc;
+ unsigned char *buf;
+
+ if (buflen > 16)
+ buflen = 16;
+ memset(serial_no, 0xff, buflen);
+ buf = kzalloc(PAGE_83_INQ_BYTES, GFP_KERNEL);
+ if (!buf)
+ return;
+ memset(serial_no, 0, buflen);
+ if (withirq)
+ rc = sendcmd_withirq(CISS_INQUIRY, ctlr, buf,
+ PAGE_83_INQ_BYTES, 1, logvol, 0x83, TYPE_CMD);
+ else
+ rc = sendcmd(CISS_INQUIRY, ctlr, buf,
+ PAGE_83_INQ_BYTES, 1, logvol, 0x83, NULL, TYPE_CMD);
+ if (rc == IO_OK)
+ memcpy(serial_no, &buf[8], buflen);
+ kfree(buf);
+ return;
+}
+
+static void cciss_add_disk(ctlr_info_t *h, struct gendisk *disk,
+ int drv_index)
+{
+ disk->queue = blk_init_queue(do_cciss_request, &h->lock);
+ sprintf(disk->disk_name, "cciss/c%dd%d", h->ctlr, drv_index);
+ disk->major = h->major;
+ disk->first_minor = drv_index << NWD_SHIFT;
+ disk->fops = &cciss_fops;
+ disk->private_data = &h->drv[drv_index];
+
+ /* Set up queue information */
+ blk_queue_bounce_limit(disk->queue, h->pdev->dma_mask);
+
+ /* This is a hardware imposed limit. */
+ blk_queue_max_hw_segments(disk->queue, MAXSGENTRIES);
+
+ /* This is a limit in the driver and could be eliminated. */
+ blk_queue_max_phys_segments(disk->queue, MAXSGENTRIES);
+
+ blk_queue_max_sectors(disk->queue, h->cciss_max_sectors);
+
+ blk_queue_softirq_done(disk->queue, cciss_softirq_done);
+
+ disk->queue->queuedata = h;
+
+ blk_queue_hardsect_size(disk->queue,
+ h->drv[drv_index].block_size);
+
+ /* Make sure all queue data is written out before */
+ /* setting h->drv[drv_index].queue, as setting this */
+ /* allows the interrupt handler to start the queue */
+ wmb();
+ h->drv[drv_index].queue = disk->queue;
+ add_disk(disk);
+}
+
/* This function will check the usage_count of the drive to be updated/added.
- * If the usage_count is zero then the drive information will be updated and
- * the disk will be re-registered with the kernel. If not then it will be
- * left alone for the next reboot. The exception to this is disk 0 which
- * will always be left registered with the kernel since it is also the
- * controller node. Any changes to disk 0 will show up on the next
- * reboot.
+ * If the usage_count is zero and it is a heretofore unknown drive, or,
+ * the drive's capacity, geometry, or serial number has changed,
+ * then the drive information will be updated and the disk will be
+ * re-registered with the kernel. If these conditions don't hold,
+ * then it will be left alone for the next reboot. The exception to this
+ * is disk 0 which will always be left registered with the kernel since it
+ * is also the controller node. Any changes to disk 0 will show up on
+ * the next reboot.
*/
-static void cciss_update_drive_info(int ctlr, int drv_index)
+static void cciss_update_drive_info(int ctlr, int drv_index, int first_time)
{
ctlr_info_t *h = hba[ctlr];
struct gendisk *disk;
sector_t total_size;
unsigned long flags = 0;
int ret = 0;
+ drive_info_struct *drvinfo;
+ int was_only_controller_node;
+
+ /* Get information about the disk and modify the driver structure */
+ inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL);
+ drvinfo = kmalloc(sizeof(*drvinfo), GFP_KERNEL);
+ if (inq_buff == NULL || drvinfo == NULL)
+ goto mem_msg;
+
+ /* See if we're trying to update the "controller node"
+ * this will happen the when the first logical drive gets
+ * created by ACU.
+ */
+ was_only_controller_node = (drv_index == 0 &&
+ h->drv[0].raid_level == -1);
- /* if the disk already exists then deregister it before proceeding */
- if (h->drv[drv_index].raid_level != -1) {
+ /* testing to see if 16-byte CDBs are already being used */
+ if (h->cciss_read == CCISS_READ_16) {
+ cciss_read_capacity_16(h->ctlr, drv_index, 1,
+ &total_size, &block_size);
+
+ } else {
+ cciss_read_capacity(ctlr, drv_index, 1,
+ &total_size, &block_size);
+
+ /* if read_capacity returns all F's this volume is >2TB */
+ /* in size so we switch to 16-byte CDB's for all */
+ /* read/write ops */
+ if (total_size == 0xFFFFFFFFULL) {
+ cciss_read_capacity_16(ctlr, drv_index, 1,
+ &total_size, &block_size);
+ h->cciss_read = CCISS_READ_16;
+ h->cciss_write = CCISS_WRITE_16;
+ } else {
+ h->cciss_read = CCISS_READ_10;
+ h->cciss_write = CCISS_WRITE_10;
+ }
+ }
+
+ cciss_geometry_inquiry(ctlr, drv_index, 1, total_size, block_size,
+ inq_buff, drvinfo);
+ drvinfo->block_size = block_size;
+ drvinfo->nr_blocks = total_size + 1;
+
+ cciss_get_serial_no(ctlr, drv_index, 1, drvinfo->serial_no,
+ sizeof(drvinfo->serial_no));
+
+ /* Is it the same disk we already know, and nothing's changed? */
+ if (h->drv[drv_index].raid_level != -1 &&
+ ((memcmp(drvinfo->serial_no,
+ h->drv[drv_index].serial_no, 16) == 0) &&
+ drvinfo->block_size == h->drv[drv_index].block_size &&
+ drvinfo->nr_blocks == h->drv[drv_index].nr_blocks &&
+ drvinfo->heads == h->drv[drv_index].heads &&
+ drvinfo->sectors == h->drv[drv_index].sectors &&
+ drvinfo->cylinders == h->drv[drv_index].cylinders))
+ /* The disk is unchanged, nothing to update */
+ goto freeret;
+
+ /* If we get here it's not the same disk, or something's changed,
+ * so we need to * deregister it, and re-register it, if it's not
+ * in use.
+ * If the disk already exists then deregister it before proceeding
+ * (unless it's the first disk (for the controller node).
+ */
+ if (h->drv[drv_index].raid_level != -1 && drv_index != 0) {
+ printk(KERN_WARNING "disk %d has changed.\n", drv_index);
spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
h->drv[drv_index].busy_configuring = 1;
spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- /* deregister_disk sets h->drv[drv_index].queue = NULL */
- /* which keeps the interrupt handler from starting */
- /* the queue. */
+ /* deregister_disk sets h->drv[drv_index].queue = NULL
+ * which keeps the interrupt handler from starting
+ * the queue.
+ */
ret = deregister_disk(h->gendisk[drv_index],
&h->drv[drv_index], 0);
h->drv[drv_index].busy_configuring = 0;
/* If the disk is in use return */
if (ret)
- return;
+ goto freeret;
- /* Get information about the disk and modify the driver structure */
- inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL);
- if (inq_buff == NULL)
- goto mem_msg;
-
- /* testing to see if 16-byte CDBs are already being used */
- if (h->cciss_read == CCISS_READ_16) {
- cciss_read_capacity_16(h->ctlr, drv_index, 1,
- &total_size, &block_size);
- goto geo_inq;
- }
-
- cciss_read_capacity(ctlr, drv_index, 1,
- &total_size, &block_size);
-
- /* if read_capacity returns all F's this volume is >2TB in size */
- /* so we switch to 16-byte CDB's for all read/write ops */
- if (total_size == 0xFFFFFFFFULL) {
- cciss_read_capacity_16(ctlr, drv_index, 1,
- &total_size, &block_size);
- h->cciss_read = CCISS_READ_16;
- h->cciss_write = CCISS_WRITE_16;
- } else {
- h->cciss_read = CCISS_READ_10;
- h->cciss_write = CCISS_WRITE_10;
- }
-geo_inq:
- cciss_geometry_inquiry(ctlr, drv_index, 1, total_size, block_size,
- inq_buff, &h->drv[drv_index]);
+ /* Save the new information from cciss_geometry_inquiry
+ * and serial number inquiry.
+ */
+ h->drv[drv_index].block_size = drvinfo->block_size;
+ h->drv[drv_index].nr_blocks = drvinfo->nr_blocks;
+ h->drv[drv_index].heads = drvinfo->heads;
+ h->drv[drv_index].sectors = drvinfo->sectors;
+ h->drv[drv_index].cylinders = drvinfo->cylinders;
+ h->drv[drv_index].raid_level = drvinfo->raid_level;
+ memcpy(h->drv[drv_index].serial_no, drvinfo->serial_no, 16);
++h->num_luns;
disk = h->gendisk[drv_index];
set_capacity(disk, h->drv[drv_index].nr_blocks);
- /* if it's the controller it's already added */
- if (drv_index) {
- disk->queue = blk_init_queue(do_cciss_request, &h->lock);
- sprintf(disk->disk_name, "cciss/c%dd%d", ctlr, drv_index);
- disk->major = h->major;
- disk->first_minor = drv_index << NWD_SHIFT;
- disk->fops = &cciss_fops;
- disk->private_data = &h->drv[drv_index];
-
- /* Set up queue information */
- blk_queue_bounce_limit(disk->queue, hba[ctlr]->pdev->dma_mask);
-
- /* This is a hardware imposed limit. */
- blk_queue_max_hw_segments(disk->queue, MAXSGENTRIES);
-
- /* This is a limit in the driver and could be eliminated. */
- blk_queue_max_phys_segments(disk->queue, MAXSGENTRIES);
-
- blk_queue_max_sectors(disk->queue, h->cciss_max_sectors);
-
- blk_queue_softirq_done(disk->queue, cciss_softirq_done);
-
- disk->queue->queuedata = hba[ctlr];
-
- blk_queue_hardsect_size(disk->queue,
- hba[ctlr]->drv[drv_index].block_size);
-
- /* Make sure all queue data is written out before */
- /* setting h->drv[drv_index].queue, as setting this */
- /* allows the interrupt handler to start the queue */
- wmb();
- h->drv[drv_index].queue = disk->queue;
- add_disk(disk);
- }
+ /* If it's not disk 0 (drv_index != 0)
+ * or if it was disk 0, but there was previously
+ * no actual corresponding configured logical drive
+ * (raid_leve == -1) then we want to update the
+ * logical drive's information.
+ */
+ if (drv_index || first_time)
+ cciss_add_disk(h, disk, drv_index);
- freeret:
+freeret:
kfree(inq_buff);
+ kfree(drvinfo);
return;
- mem_msg:
+mem_msg:
printk(KERN_ERR "cciss: out of memory\n");
goto freeret;
}
* where new drives will be added. If the index to be returned is greater
* than the highest_lun index for the controller then highest_lun is set
* to this new index. If there are no available indexes then -1 is returned.
+ * "controller_node" is used to know if this is a real logical drive, or just
+ * the controller node, which determines if this counts towards highest_lun.
*/
-static int cciss_find_free_drive_index(int ctlr)
+static int cciss_find_free_drive_index(int ctlr, int controller_node)
{
int i;
for (i = 0; i < CISS_MAX_LUN; i++) {
if (hba[ctlr]->drv[i].raid_level == -1) {
if (i > hba[ctlr]->highest_lun)
- hba[ctlr]->highest_lun = i;
+ if (!controller_node)
+ hba[ctlr]->highest_lun = i;
return i;
}
}
return -1;
}
+/* cciss_add_gendisk finds a free hba[]->drv structure
+ * and allocates a gendisk if needed, and sets the lunid
+ * in the drvinfo structure. It returns the index into
+ * the ->drv[] array, or -1 if none are free.
+ * is_controller_node indicates whether highest_lun should
+ * count this disk, or if it's only being added to provide
+ * a means to talk to the controller in case no logical
+ * drives have yet been configured.
+ */
+static int cciss_add_gendisk(ctlr_info_t *h, __u32 lunid, int controller_node)
+{
+ int drv_index;
+
+ drv_index = cciss_find_free_drive_index(h->ctlr, controller_node);
+ if (drv_index == -1)
+ return -1;
+ /*Check if the gendisk needs to be allocated */
+ if (!h->gendisk[drv_index]) {
+ h->gendisk[drv_index] =
+ alloc_disk(1 << NWD_SHIFT);
+ if (!h->gendisk[drv_index]) {
+ printk(KERN_ERR "cciss%d: could not "
+ "allocate a new disk %d\n",
+ h->ctlr, drv_index);
+ return -1;
+ }
+ }
+ h->drv[drv_index].LunID = lunid;
+
+ /* Don't need to mark this busy because nobody */
+ /* else knows about this disk yet to contend */
+ /* for access to it. */
+ h->drv[drv_index].busy_configuring = 0;
+ wmb();
+ return drv_index;
+}
+
+/* This is for the special case of a controller which
+ * has no logical drives. In this case, we still need
+ * to register a disk so the controller can be accessed
+ * by the Array Config Utility.
+ */
+static void cciss_add_controller_node(ctlr_info_t *h)
+{
+ struct gendisk *disk;
+ int drv_index;
+
+ if (h->gendisk[0] != NULL) /* already did this? Then bail. */
+ return;
+
+ drv_index = cciss_add_gendisk(h, 0, 1);
+ if (drv_index == -1) {
+ printk(KERN_WARNING "cciss%d: could not "
+ "add disk 0.\n", h->ctlr);
+ return;
+ }
+ h->drv[drv_index].block_size = 512;
+ h->drv[drv_index].nr_blocks = 0;
+ h->drv[drv_index].heads = 0;
+ h->drv[drv_index].sectors = 0;
+ h->drv[drv_index].cylinders = 0;
+ h->drv[drv_index].raid_level = -1;
+ memset(h->drv[drv_index].serial_no, 0, 16);
+ disk = h->gendisk[drv_index];
+ cciss_add_disk(h, disk, drv_index);
+}
+
/* This function will add and remove logical drives from the Logical
* drive array of the controller and maintain persistency of ordering
* so that mount points are preserved until the next reboot. This allows
* without a re-ordering of those drives.
* INPUT
* h = The controller to perform the operations on
- * del_disk = The disk to remove if specified. If the value given
- * is NULL then no disk is removed.
*/
-static int rebuild_lun_table(ctlr_info_t *h, struct gendisk *del_disk)
+static int rebuild_lun_table(ctlr_info_t *h, int first_time)
{
int ctlr = h->ctlr;
int num_luns;
ReportLunData_struct *ld_buff = NULL;
- drive_info_struct *drv = NULL;
int return_code;
int listlength = 0;
int i;
__u32 lunid = 0;
unsigned long flags;
+ if (!capable(CAP_SYS_RAWIO))
+ return -EPERM;
+
/* Set busy_configuring flag for this operation */
spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
if (h->busy_configuring) {
return -EBUSY;
}
h->busy_configuring = 1;
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- /* if del_disk is NULL then we are being called to add a new disk
- * and update the logical drive table. If it is not NULL then
- * we will check if the disk is in use or not.
- */
- if (del_disk != NULL) {
- drv = get_drv(del_disk);
- drv->busy_configuring = 1;
- spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- return_code = deregister_disk(del_disk, drv, 1);
- drv->busy_configuring = 0;
- h->busy_configuring = 0;
- return return_code;
- } else {
- spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- if (!capable(CAP_SYS_RAWIO))
- return -EPERM;
+ ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL);
+ if (ld_buff == NULL)
+ goto mem_msg;
- ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL);
- if (ld_buff == NULL)
- goto mem_msg;
-
- return_code = sendcmd_withirq(CISS_REPORT_LOG, ctlr, ld_buff,
- sizeof(ReportLunData_struct), 0,
- 0, 0, TYPE_CMD);
-
- if (return_code == IO_OK) {
- listlength =
- be32_to_cpu(*(__be32 *) ld_buff->LUNListLength);
- } else { /* reading number of logical volumes failed */
- printk(KERN_WARNING "cciss: report logical volume"
- " command failed\n");
- listlength = 0;
- goto freeret;
- }
+ return_code = sendcmd_withirq(CISS_REPORT_LOG, ctlr, ld_buff,
+ sizeof(ReportLunData_struct), 0,
+ 0, 0, TYPE_CMD);
+
+ if (return_code == IO_OK)
+ listlength = be32_to_cpu(*(__be32 *) ld_buff->LUNListLength);
+ else { /* reading number of logical volumes failed */
+ printk(KERN_WARNING "cciss: report logical volume"
+ " command failed\n");
+ listlength = 0;
+ goto freeret;
+ }
+
+ num_luns = listlength / 8; /* 8 bytes per entry */
+ if (num_luns > CISS_MAX_LUN) {
+ num_luns = CISS_MAX_LUN;
+ printk(KERN_WARNING "cciss: more luns configured"
+ " on controller than can be handled by"
+ " this driver.\n");
+ }
- num_luns = listlength / 8; /* 8 bytes per entry */
- if (num_luns > CISS_MAX_LUN) {
- num_luns = CISS_MAX_LUN;
- printk(KERN_WARNING "cciss: more luns configured"
- " on controller than can be handled by"
- " this driver.\n");
+ if (num_luns == 0)
+ cciss_add_controller_node(h);
+
+ /* Compare controller drive array to driver's drive array
+ * to see if any drives are missing on the controller due
+ * to action of Array Config Utility (user deletes drive)
+ * and deregister logical drives which have disappeared.
+ */
+ for (i = 0; i <= h->highest_lun; i++) {
+ int j;
+ drv_found = 0;
+ for (j = 0; j < num_luns; j++) {
+ memcpy(&lunid, &ld_buff->LUN[j][0], 4);
+ lunid = le32_to_cpu(lunid);
+ if (h->drv[i].LunID == lunid) {
+ drv_found = 1;
+ break;
+ }
+ }
+ if (!drv_found) {
+ /* Deregister it from the OS, it's gone. */
+ spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
+ h->drv[i].busy_configuring = 1;
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return_code = deregister_disk(h->gendisk[i],
+ &h->drv[i], 1);
+ h->drv[i].busy_configuring = 0;
}
+ }
+
+ /* Compare controller drive array to driver's drive array.
+ * Check for updates in the drive information and any new drives
+ * on the controller due to ACU adding logical drives, or changing
+ * a logical drive's size, etc. Reregister any new/changed drives
+ */
+ for (i = 0; i < num_luns; i++) {
+ int j;
+
+ drv_found = 0;
+
+ memcpy(&lunid, &ld_buff->LUN[i][0], 4);
+ lunid = le32_to_cpu(lunid);
- /* Compare controller drive array to drivers drive array.
- * Check for updates in the drive information and any new drives
- * on the controller.
+ /* Find if the LUN is already in the drive array
+ * of the driver. If so then update its info
+ * if not in use. If it does not exist then find
+ * the first free index and add it.
*/
- for (i = 0; i < num_luns; i++) {
- int j;
-
- drv_found = 0;
-
- lunid = (0xff &
- (unsigned int)(ld_buff->LUN[i][3])) << 24;
- lunid |= (0xff &
- (unsigned int)(ld_buff->LUN[i][2])) << 16;
- lunid |= (0xff &
- (unsigned int)(ld_buff->LUN[i][1])) << 8;
- lunid |= 0xff & (unsigned int)(ld_buff->LUN[i][0]);
-
- /* Find if the LUN is already in the drive array
- * of the controller. If so then update its info
- * if not is use. If it does not exist then find
- * the first free index and add it.
- */
- for (j = 0; j <= h->highest_lun; j++) {
- if (h->drv[j].LunID == lunid) {
- drv_index = j;
- drv_found = 1;
- }
+ for (j = 0; j <= h->highest_lun; j++) {
+ if (h->drv[j].raid_level != -1 &&
+ h->drv[j].LunID == lunid) {
+ drv_index = j;
+ drv_found = 1;
+ break;
}
+ }
- /* check if the drive was found already in the array */
- if (!drv_found) {
- drv_index = cciss_find_free_drive_index(ctlr);
- if (drv_index == -1)
- goto freeret;
-
- /*Check if the gendisk needs to be allocated */
- if (!h->gendisk[drv_index]){
- h->gendisk[drv_index] = alloc_disk(1 << NWD_SHIFT);
- if (!h->gendisk[drv_index]){
- printk(KERN_ERR "cciss: could not allocate new disk %d\n", drv_index);
- goto mem_msg;
- }
- }
- }
- h->drv[drv_index].LunID = lunid;
- cciss_update_drive_info(ctlr, drv_index);
- } /* end for */
- } /* end else */
+ /* check if the drive was found already in the array */
+ if (!drv_found) {
+ drv_index = cciss_add_gendisk(h, lunid, 0);
+ if (drv_index == -1)
+ goto freeret;
+ }
+ cciss_update_drive_info(ctlr, drv_index, first_time);
+ } /* end for */
- freeret:
+freeret:
kfree(ld_buff);
h->busy_configuring = 0;
/* We return -1 here to tell the ACU that we have registered/updated
* additional times.
*/
return -1;
- mem_msg:
+mem_msg:
printk(KERN_ERR "cciss: out of memory\n");
+ h->busy_configuring = 0;
goto freeret;
}
* other than disk 0 we will call put_disk. We do not
* do this for disk 0 as we need it to be able to
* configure the controller.
- */
+ */
if (clear_all){
/* This isn't pretty, but we need to find the
* disk in our array and NULL our the pointer.
* This is so that we will call alloc_disk if
* this index is used again later.
- */
+ */
for (i=0; i < CISS_MAX_LUN; i++){
- if(h->gendisk[i] == disk){
+ if (h->gendisk[i] == disk) {
h->gendisk[i] = NULL;
break;
}
if (drv == h->drv + h->highest_lun) {
/* if so, find the new hightest lun */
int i, newhighest = -1;
- for (i = 0; i < h->highest_lun; i++) {
+ for (i = 0; i <= h->highest_lun; i++) {
/* if the disk has size > 0, it is available */
if (h->drv[i].heads)
newhighest = i;
return err;
}
-/*
- * Gets information about the local volumes attached to the controller.
+/* Function to find the first free pointer into our hba[] array
+ * Returns -1 if no free entries are left.
*/
-static void cciss_getgeometry(int cntl_num)
-{
- ReportLunData_struct *ld_buff;
- InquiryData_struct *inq_buff;
- int return_code;
- int i;
- int listlength = 0;
- __u32 lunid = 0;
- unsigned block_size;
- sector_t total_size;
-
- ld_buff = kzalloc(sizeof(ReportLunData_struct), GFP_KERNEL);
- if (ld_buff == NULL) {
- printk(KERN_ERR "cciss: out of memory\n");
- return;
- }
- inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL);
- if (inq_buff == NULL) {
- printk(KERN_ERR "cciss: out of memory\n");
- kfree(ld_buff);
- return;
- }
- /* Get the firmware version */
- return_code = sendcmd(CISS_INQUIRY, cntl_num, inq_buff,
- sizeof(InquiryData_struct), 0, 0, 0, NULL,
- TYPE_CMD);
- if (return_code == IO_OK) {
- hba[cntl_num]->firm_ver[0] = inq_buff->data_byte[32];
- hba[cntl_num]->firm_ver[1] = inq_buff->data_byte[33];
- hba[cntl_num]->firm_ver[2] = inq_buff->data_byte[34];
- hba[cntl_num]->firm_ver[3] = inq_buff->data_byte[35];
- } else { /* send command failed */
-
- printk(KERN_WARNING "cciss: unable to determine firmware"
- " version of controller\n");
- }
- /* Get the number of logical volumes */
- return_code = sendcmd(CISS_REPORT_LOG, cntl_num, ld_buff,
- sizeof(ReportLunData_struct), 0, 0, 0, NULL,
- TYPE_CMD);
-
- if (return_code == IO_OK) {
-#ifdef CCISS_DEBUG
- printk("LUN Data\n--------------------------\n");
-#endif /* CCISS_DEBUG */
-
- listlength |=
- (0xff & (unsigned int)(ld_buff->LUNListLength[0])) << 24;
- listlength |=
- (0xff & (unsigned int)(ld_buff->LUNListLength[1])) << 16;
- listlength |=
- (0xff & (unsigned int)(ld_buff->LUNListLength[2])) << 8;
- listlength |= 0xff & (unsigned int)(ld_buff->LUNListLength[3]);
- } else { /* reading number of logical volumes failed */
-
- printk(KERN_WARNING "cciss: report logical volume"
- " command failed\n");
- listlength = 0;
- }
- hba[cntl_num]->num_luns = listlength / 8; // 8 bytes pre entry
- if (hba[cntl_num]->num_luns > CISS_MAX_LUN) {
- printk(KERN_ERR
- "ciss: only %d number of logical volumes supported\n",
- CISS_MAX_LUN);
- hba[cntl_num]->num_luns = CISS_MAX_LUN;
- }
-#ifdef CCISS_DEBUG
- printk(KERN_DEBUG "Length = %x %x %x %x = %d\n",
- ld_buff->LUNListLength[0], ld_buff->LUNListLength[1],
- ld_buff->LUNListLength[2], ld_buff->LUNListLength[3],
- hba[cntl_num]->num_luns);
-#endif /* CCISS_DEBUG */
-
- hba[cntl_num]->highest_lun = hba[cntl_num]->num_luns - 1;
- for (i = 0; i < CISS_MAX_LUN; i++) {
- if (i < hba[cntl_num]->num_luns) {
- lunid = (0xff & (unsigned int)(ld_buff->LUN[i][3]))
- << 24;
- lunid |= (0xff & (unsigned int)(ld_buff->LUN[i][2]))
- << 16;
- lunid |= (0xff & (unsigned int)(ld_buff->LUN[i][1]))
- << 8;
- lunid |= 0xff & (unsigned int)(ld_buff->LUN[i][0]);
-
- hba[cntl_num]->drv[i].LunID = lunid;
-
-#ifdef CCISS_DEBUG
- printk(KERN_DEBUG "LUN[%d]: %x %x %x %x = %x\n", i,
- ld_buff->LUN[i][0], ld_buff->LUN[i][1],
- ld_buff->LUN[i][2], ld_buff->LUN[i][3],
- hba[cntl_num]->drv[i].LunID);
-#endif /* CCISS_DEBUG */
-
- /* testing to see if 16-byte CDBs are already being used */
- if(hba[cntl_num]->cciss_read == CCISS_READ_16) {
- cciss_read_capacity_16(cntl_num, i, 0,
- &total_size, &block_size);
- goto geo_inq;
- }
- cciss_read_capacity(cntl_num, i, 0, &total_size, &block_size);
-
- /* If read_capacity returns all F's the logical is >2TB */
- /* so we switch to 16-byte CDBs for all read/write ops */
- if(total_size == 0xFFFFFFFFULL) {
- cciss_read_capacity_16(cntl_num, i, 0,
- &total_size, &block_size);
- hba[cntl_num]->cciss_read = CCISS_READ_16;
- hba[cntl_num]->cciss_write = CCISS_WRITE_16;
- } else {
- hba[cntl_num]->cciss_read = CCISS_READ_10;
- hba[cntl_num]->cciss_write = CCISS_WRITE_10;
- }
-geo_inq:
- cciss_geometry_inquiry(cntl_num, i, 0, total_size,
- block_size, inq_buff,
- &hba[cntl_num]->drv[i]);
- } else {
- /* initialize raid_level to indicate a free space */
- hba[cntl_num]->drv[i].raid_level = -1;
- }
- }
- kfree(ld_buff);
- kfree(inq_buff);
-}
-
-/* Function to find the first free pointer into our hba[] array */
-/* Returns -1 if no free entries are left. */
static int alloc_cciss_hba(void)
{
int i;
p = kzalloc(sizeof(ctlr_info_t), GFP_KERNEL);
if (!p)
goto Enomem;
- p->gendisk[0] = alloc_disk(1 << NWD_SHIFT);
- if (!p->gendisk[0]) {
- kfree(p);
- goto Enomem;
- }
hba[i] = p;
return i;
}
((hba[i]->nr_cmds + BITS_PER_LONG -
1) / BITS_PER_LONG) * sizeof(unsigned long));
-#ifdef CCISS_DEBUG
- printk(KERN_DEBUG "Scanning for drives on controller cciss%d\n", i);
-#endif /* CCISS_DEBUG */
-
- cciss_getgeometry(i);
+ hba[i]->num_luns = 0;
+ hba[i]->highest_lun = -1;
+ for (j = 0; j < CISS_MAX_LUN; j++) {
+ hba[i]->drv[j].raid_level = -1;
+ hba[i]->drv[j].queue = NULL;
+ hba[i]->gendisk[j] = NULL;
+ }
cciss_scsi_setup(i);
hba[i]->busy_initializing = 0;
- do {
- drive_info_struct *drv = &(hba[i]->drv[j]);
- struct gendisk *disk = hba[i]->gendisk[j];
- struct request_queue *q;
-
- /* Check if the disk was allocated already */
- if (!disk){
- hba[i]->gendisk[j] = alloc_disk(1 << NWD_SHIFT);
- disk = hba[i]->gendisk[j];
- }
-
- /* Check that the disk was able to be allocated */
- if (!disk) {
- printk(KERN_ERR "cciss: unable to allocate memory for disk %d\n", j);
- goto clean4;
- }
-
- q = blk_init_queue(do_cciss_request, &hba[i]->lock);
- if (!q) {
- printk(KERN_ERR
- "cciss: unable to allocate queue for disk %d\n",
- j);
- goto clean4;
- }
- drv->queue = q;
-
- blk_queue_bounce_limit(q, hba[i]->pdev->dma_mask);
-
- /* This is a hardware imposed limit. */
- blk_queue_max_hw_segments(q, MAXSGENTRIES);
-
- /* This is a limit in the driver and could be eliminated. */
- blk_queue_max_phys_segments(q, MAXSGENTRIES);
-
- blk_queue_max_sectors(q, hba[i]->cciss_max_sectors);
-
- blk_queue_softirq_done(q, cciss_softirq_done);
-
- q->queuedata = hba[i];
- sprintf(disk->disk_name, "cciss/c%dd%d", i, j);
- disk->major = hba[i]->major;
- disk->first_minor = j << NWD_SHIFT;
- disk->fops = &cciss_fops;
- disk->queue = q;
- disk->private_data = drv;
- disk->driverfs_dev = &pdev->dev;
- /* we must register the controller even if no disks exist */
- /* this is for the online array utilities */
- if (!drv->heads && j)
- continue;
- blk_queue_hardsect_size(q, drv->block_size);
- set_capacity(disk, drv->nr_blocks);
- j++;
- } while (j <= hba[i]->highest_lun);
-
- /* Make sure all queue data is written out before */
- /* interrupt handler, triggered by add_disk, */
- /* is allowed to start them. */
- wmb();
-
- for (j = 0; j <= hba[i]->highest_lun; j++)
- add_disk(hba[i]->gendisk[j]);
-
- /* we must register the controller even if no disks exist */
- if (hba[i]->highest_lun == -1)
- add_disk(hba[i]->gendisk[0]);
-
+ rebuild_lun_table(hba[i], 1);
return 1;
- clean4:
+clean4:
#ifdef CONFIG_CISS_SCSI_TAPE
kfree(hba[i]->scsi_rejects.complete);
#endif
hba[i]->errinfo_pool,
hba[i]->errinfo_pool_dhandle);
free_irq(hba[i]->intr[SIMPLE_MODE_INT], hba[i]);
- clean2:
+clean2:
unregister_blkdev(hba[i]->major, hba[i]->devname);
- clean1:
+clean1:
hba[i]->busy_initializing = 0;
/* cleanup any queues that may have been initialized */
for (j=0; j <= hba[i]->highest_lun; j++){
}
}
+#ifdef CONFIG_CISS_SCSI_TAPE
cciss_unregister_scsi(i); /* unhook from SCSI subsystem */
+#endif
cciss_shutdown(pdev);
*to prevent it from being opened or it's queue
*from being started.
*/
+ __u8 serial_no[16]; /* from inquiry page 0x83, */
+ /* not necc. null terminated. */
} drive_info_struct;
#ifdef CONFIG_CISS_SCSI_TAPE
}
return (!found);
}
+struct scsi2map {
+ char scsi3addr[8];
+ int bus, target, lun;
+};
static int
cciss_scsi_add_entry(int ctlr, int hostno,
- unsigned char *scsi3addr, int devtype)
+ unsigned char *scsi3addr, int devtype,
+ struct scsi2map *added, int *nadded)
{
/* assumes hba[ctlr]->scsi_ctlr->lock is held */
int n = ccissscsi[ctlr].ndevices;
struct cciss_scsi_dev_t *sd;
+ int i, bus, target, lun;
+ unsigned char addr1[8], addr2[8];
if (n >= CCISS_MAX_SCSI_DEVS_PER_HBA) {
printk("cciss%d: Too many devices, "
"some will be inaccessible.\n", ctlr);
return -1;
}
+
+ bus = target = -1;
+ lun = 0;
+ /* Is this device a non-zero lun of a multi-lun device */
+ /* byte 4 of the 8-byte LUN addr will contain the logical unit no. */
+ if (scsi3addr[4] != 0) {
+ /* Search through our list and find the device which */
+ /* has the same 8 byte LUN address, excepting byte 4. */
+ /* Assign the same bus and target for this new LUN. */
+ /* Use the logical unit number from the firmware. */
+ memcpy(addr1, scsi3addr, 8);
+ addr1[4] = 0;
+ for (i = 0; i < n; i++) {
+ sd = &ccissscsi[ctlr].dev[i];
+ memcpy(addr2, sd->scsi3addr, 8);
+ addr2[4] = 0;
+ /* differ only in byte 4? */
+ if (memcmp(addr1, addr2, 8) == 0) {
+ bus = sd->bus;
+ target = sd->target;
+ lun = scsi3addr[4];
+ break;
+ }
+ }
+ }
+
sd = &ccissscsi[ctlr].dev[n];
- if (find_bus_target_lun(ctlr, &sd->bus, &sd->target, &sd->lun) != 0)
- return -1;
+ if (lun == 0) {
+ if (find_bus_target_lun(ctlr,
+ &sd->bus, &sd->target, &sd->lun) != 0)
+ return -1;
+ } else {
+ sd->bus = bus;
+ sd->target = target;
+ sd->lun = lun;
+ }
+ added[*nadded].bus = sd->bus;
+ added[*nadded].target = sd->target;
+ added[*nadded].lun = sd->lun;
+ (*nadded)++;
+
memcpy(&sd->scsi3addr[0], scsi3addr, 8);
sd->devtype = devtype;
ccissscsi[ctlr].ndevices++;
}
static void
-cciss_scsi_remove_entry(int ctlr, int hostno, int entry)
+cciss_scsi_remove_entry(int ctlr, int hostno, int entry,
+ struct scsi2map *removed, int *nremoved)
{
/* assumes hba[ctlr]->scsi_ctlr->lock is held */
int i;
if (entry < 0 || entry >= CCISS_MAX_SCSI_DEVS_PER_HBA) return;
sd = ccissscsi[ctlr].dev[entry];
+ removed[*nremoved].bus = sd.bus;
+ removed[*nremoved].target = sd.target;
+ removed[*nremoved].lun = sd.lun;
+ (*nremoved)++;
for (i=entry;i<ccissscsi[ctlr].ndevices-1;i++)
ccissscsi[ctlr].dev[i] = ccissscsi[ctlr].dev[i+1];
ccissscsi[ctlr].ndevices--;
(a)[1] == (b)[1] && \
(a)[0] == (b)[0])
+static void fixup_botched_add(int ctlr, char *scsi3addr)
+{
+ /* called when scsi_add_device fails in order to re-adjust */
+ /* ccissscsi[] to match the mid layer's view. */
+ unsigned long flags;
+ int i, j;
+ CPQ_TAPE_LOCK(ctlr, flags);
+ for (i = 0; i < ccissscsi[ctlr].ndevices; i++) {
+ if (memcmp(scsi3addr,
+ ccissscsi[ctlr].dev[i].scsi3addr, 8) == 0) {
+ for (j = i; j < ccissscsi[ctlr].ndevices-1; j++)
+ ccissscsi[ctlr].dev[j] =
+ ccissscsi[ctlr].dev[j+1];
+ ccissscsi[ctlr].ndevices--;
+ break;
+ }
+ }
+ CPQ_TAPE_UNLOCK(ctlr, flags);
+}
+
static int
adjust_cciss_scsi_table(int ctlr, int hostno,
struct cciss_scsi_dev_t sd[], int nsds)
int i,j, found, changes=0;
struct cciss_scsi_dev_t *csd;
unsigned long flags;
+ struct scsi2map *added, *removed;
+ int nadded, nremoved;
+ struct Scsi_Host *sh = NULL;
+
+ added = kzalloc(sizeof(*added) * CCISS_MAX_SCSI_DEVS_PER_HBA,
+ GFP_KERNEL);
+ removed = kzalloc(sizeof(*removed) * CCISS_MAX_SCSI_DEVS_PER_HBA,
+ GFP_KERNEL);
+
+ if (!added || !removed) {
+ printk(KERN_WARNING "cciss%d: Out of memory in "
+ "adjust_cciss_scsi_table\n", ctlr);
+ goto free_and_out;
+ }
CPQ_TAPE_LOCK(ctlr, flags);
+ if (hostno != -1) /* if it's not the first time... */
+ sh = ((struct cciss_scsi_adapter_data_t *)
+ hba[ctlr]->scsi_ctlr)->scsi_host;
+
/* find any devices in ccissscsi[] that are not in
sd[] and remove them from ccissscsi[] */
i = 0;
+ nremoved = 0;
+ nadded = 0;
while(i<ccissscsi[ctlr].ndevices) {
csd = &ccissscsi[ctlr].dev[i];
found=0;
/* printk("cciss%d: %s device c%db%dt%dl%d removed.\n",
ctlr, scsi_device_type(csd->devtype), hostno,
csd->bus, csd->target, csd->lun); */
- cciss_scsi_remove_entry(ctlr, hostno, i);
- /* note, i not incremented */
+ cciss_scsi_remove_entry(ctlr, hostno, i,
+ removed, &nremoved);
+ /* remove ^^^, hence i not incremented */
}
else if (found == 1) { /* device is different kind */
changes++;
"(device type now %s).\n",
ctlr, hostno, csd->bus, csd->target, csd->lun,
scsi_device_type(csd->devtype));
+ cciss_scsi_remove_entry(ctlr, hostno, i,
+ removed, &nremoved);
+ /* remove ^^^, hence i not incremented */
+ if (cciss_scsi_add_entry(ctlr, hostno,
+ &sd[j].scsi3addr[0], sd[j].devtype,
+ added, &nadded) != 0)
+ /* we just removed one, so add can't fail. */
+ BUG();
csd->devtype = sd[j].devtype;
- i++; /* so just move along. */
} else /* device is same as it ever was, */
i++; /* so just move along. */
}
if (!found) {
changes++;
if (cciss_scsi_add_entry(ctlr, hostno,
- &sd[i].scsi3addr[0], sd[i].devtype) != 0)
+
+ &sd[i].scsi3addr[0], sd[i].devtype,
+ added, &nadded) != 0)
break;
} else if (found == 1) {
/* should never happen... */
}
CPQ_TAPE_UNLOCK(ctlr, flags);
- if (!changes)
- printk("cciss%d: No device changes detected.\n", ctlr);
+ /* Don't notify scsi mid layer of any changes the first time through */
+ /* (or if there are no changes) scsi_scan_host will do it later the */
+ /* first time through. */
+ if (hostno == -1 || !changes)
+ goto free_and_out;
+
+ /* Notify scsi mid layer of any removed devices */
+ for (i = 0; i < nremoved; i++) {
+ struct scsi_device *sdev =
+ scsi_device_lookup(sh, removed[i].bus,
+ removed[i].target, removed[i].lun);
+ if (sdev != NULL) {
+ scsi_remove_device(sdev);
+ scsi_device_put(sdev);
+ } else {
+ /* We don't expect to get here. */
+ /* future cmds to this device will get selection */
+ /* timeout as if the device was gone. */
+ printk(KERN_WARNING "cciss%d: didn't find "
+ "c%db%dt%dl%d\n for removal.",
+ ctlr, hostno, removed[i].bus,
+ removed[i].target, removed[i].lun);
+ }
+ }
+
+ /* Notify scsi mid layer of any added devices */
+ for (i = 0; i < nadded; i++) {
+ int rc;
+ rc = scsi_add_device(sh, added[i].bus,
+ added[i].target, added[i].lun);
+ if (rc == 0)
+ continue;
+ printk(KERN_WARNING "cciss%d: scsi_add_device "
+ "c%db%dt%dl%d failed, device not added.\n",
+ ctlr, hostno,
+ added[i].bus, added[i].target, added[i].lun);
+ /* now we have to remove it from ccissscsi, */
+ /* since it didn't get added to scsi mid layer */
+ fixup_botched_add(ctlr, added[i].scsi3addr);
+ }
+free_and_out:
+ kfree(added);
+ kfree(removed);
return 0;
}
kfree(sa);
}
-static int
-cciss_register_scsi(int ctlr)
-{
- unsigned long flags;
-
- CPQ_TAPE_LOCK(ctlr, flags);
-
- /* Since this is really a block driver, the SCSI core may not be
- initialized at init time, in which case, calling scsi_register_host
- would hang. Instead, we do it later, via /proc filesystem
- and rc scripts, when we know SCSI core is good to go. */
-
- /* Only register if SCSI devices are detected. */
- if (ccissscsi[ctlr].ndevices != 0) {
- ((struct cciss_scsi_adapter_data_t *)
- hba[ctlr]->scsi_ctlr)->registered = 1;
- CPQ_TAPE_UNLOCK(ctlr, flags);
- return cciss_scsi_detect(ctlr);
- }
- CPQ_TAPE_UNLOCK(ctlr, flags);
- printk(KERN_INFO
- "cciss%d: No appropriate SCSI device detected, "
- "SCSI subsystem not engaged.\n", ctlr);
- return 0;
-}
-
static int
cciss_engage_scsi(int ctlr)
{
sa = (struct cciss_scsi_adapter_data_t *) hba[ctlr]->scsi_ctlr;
stk = &sa->cmd_stack;
- if (((struct cciss_scsi_adapter_data_t *)
- hba[ctlr]->scsi_ctlr)->registered) {
+ if (sa->registered) {
printk("cciss%d: SCSI subsystem already engaged.\n", ctlr);
spin_unlock_irqrestore(CCISS_LOCK(ctlr), flags);
return ENXIO;
}
+ sa->registered = 1;
spin_unlock_irqrestore(CCISS_LOCK(ctlr), flags);
cciss_update_non_disk_devices(ctlr, -1);
- cciss_register_scsi(ctlr);
+ cciss_scsi_detect(ctlr);
return 0;
}
/* If no tape support, then these become defined out of existence */
#define cciss_scsi_setup(cntl_num)
-#define cciss_unregister_scsi(ctlr)
-#define cciss_register_scsi(ctlr)
#endif /* CONFIG_CISS_SCSI_TAPE */
return 0;
}
-int blkif_ioctl(struct inode *inode, struct file *filep,
- unsigned command, unsigned long argument)
+static int blkif_ioctl(struct inode *inode, struct file *filep,
+ unsigned command, unsigned long argument)
{
struct blkfront_info *info =
inode->i_bdev->bd_disk->private_data;
#define BT_DBG(D...)
#endif
-#define VERSION "1.1"
-
-static int ignore = 0;
+#define VERSION "1.2"
static struct usb_device_id bcm203x_table[] = {
/* Broadcom Blutonium (BCM2033) */
BT_DBG("intf %p id %p", intf, id);
- if (ignore || (intf->cur_altsetting->desc.bInterfaceNumber != 0))
+ if (intf->cur_altsetting->desc.bInterfaceNumber != 0)
return -ENODEV;
data = kzalloc(sizeof(*data), GFP_KERNEL);
module_init(bcm203x_init);
module_exit(bcm203x_exit);
-module_param(ignore, bool, 0644);
-MODULE_PARM_DESC(ignore, "Ignore devices from the matching table");
-
MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
MODULE_DESCRIPTION("Broadcom Blutonium firmware driver ver " VERSION);
MODULE_VERSION(VERSION);
#define BT_DBG(D...)
#endif
-#define VERSION "1.1"
-
-static int ignore = 0;
+#define VERSION "1.2"
static struct usb_driver bfusb_driver;
BT_DBG("intf %p id %p", intf, id);
- if (ignore)
- return -ENODEV;
-
/* Check number of endpoints */
if (intf->cur_altsetting->desc.bNumEndpoints < 2)
return -EIO;
module_init(bfusb_init);
module_exit(bfusb_exit);
-module_param(ignore, bool, 0644);
-MODULE_PARM_DESC(ignore, "Ignore devices from the matching table");
-
MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
MODULE_DESCRIPTION("BlueFRITZ! USB driver ver " VERSION);
MODULE_VERSION(VERSION);
#define BT_DBG(D...)
#endif
-#define VERSION "0.9"
-
-static int ignore = 0;
+#define VERSION "0.10"
static struct usb_device_id bpa10x_table[] = {
/* Tektronix BPA 100/105 (Digianswer) */
BT_DBG("intf %p id %p", intf, id);
- if (ignore)
- return -ENODEV;
-
if (intf->cur_altsetting->desc.bInterfaceNumber != 0)
return -ENODEV;
module_init(bpa10x_init);
module_exit(bpa10x_exit);
-module_param(ignore, bool, 0644);
-MODULE_PARM_DESC(ignore, "Ignore devices from the matching table");
-
MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
MODULE_DESCRIPTION("Digianswer Bluetooth USB driver ver " VERSION);
MODULE_VERSION(VERSION);
#define BT_DBG(D...)
#endif
-#define VERSION "0.1"
+#define VERSION "0.2"
+
+static int ignore_dga;
+static int ignore_csr;
+static int ignore_sniffer;
+static int disable_scofix;
+static int force_scofix;
+static int reset;
+
+static struct usb_driver btusb_driver;
+
+#define BTUSB_IGNORE 0x01
+#define BTUSB_RESET 0x02
+#define BTUSB_DIGIANSWER 0x04
+#define BTUSB_CSR 0x08
+#define BTUSB_SNIFFER 0x10
+#define BTUSB_BCM92035 0x20
+#define BTUSB_BROKEN_ISOC 0x40
+#define BTUSB_WRONG_SCO_MTU 0x80
static struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
{ USB_DEVICE_INFO(0xe0, 0x01, 0x01) },
+ /* AVM BlueFRITZ! USB v2.0 */
+ { USB_DEVICE(0x057c, 0x3800) },
+
+ /* Bluetooth Ultraport Module from IBM */
+ { USB_DEVICE(0x04bf, 0x030a) },
+
+ /* ALPS Modules with non-standard id */
+ { USB_DEVICE(0x044e, 0x3001) },
+ { USB_DEVICE(0x044e, 0x3002) },
+
+ /* Ericsson with non-standard id */
+ { USB_DEVICE(0x0bdb, 0x1002) },
+
+ /* Canyon CN-BTU1 with HID interfaces */
+ { USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_RESET },
+
{ } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, btusb_table);
static struct usb_device_id blacklist_table[] = {
+ /* CSR BlueCore devices */
+ { USB_DEVICE(0x0a12, 0x0001), .driver_info = BTUSB_CSR },
+
+ /* Broadcom BCM2033 without firmware */
+ { USB_DEVICE(0x0a5c, 0x2033), .driver_info = BTUSB_IGNORE },
+
+ /* Broadcom BCM2035 */
+ { USB_DEVICE(0x0a5c, 0x2035), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+ { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Broadcom BCM2045 */
+ { USB_DEVICE(0x0a5c, 0x2039), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+ { USB_DEVICE(0x0a5c, 0x2101), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Broadcom BCM2046 */
+ { USB_DEVICE(0x0a5c, 0x2151), .driver_info = BTUSB_RESET },
+
+ /* IBM/Lenovo ThinkPad with Broadcom chip */
+ { USB_DEVICE(0x0a5c, 0x201e), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+ { USB_DEVICE(0x0a5c, 0x2110), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Targus ACB10US */
+ { USB_DEVICE(0x0a5c, 0x2100), .driver_info = BTUSB_RESET },
+
+ /* ANYCOM Bluetooth USB-200 and USB-250 */
+ { USB_DEVICE(0x0a5c, 0x2111), .driver_info = BTUSB_RESET },
+
+ /* HP laptop with Broadcom chip */
+ { USB_DEVICE(0x03f0, 0x171d), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Dell laptop with Broadcom chip */
+ { USB_DEVICE(0x413c, 0x8126), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Dell Wireless 370 */
+ { USB_DEVICE(0x413c, 0x8156), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Dell Wireless 410 */
+ { USB_DEVICE(0x413c, 0x8152), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Microsoft Wireless Transceiver for Bluetooth 2.0 */
+ { USB_DEVICE(0x045e, 0x009c), .driver_info = BTUSB_RESET },
+
+ /* Kensington Bluetooth USB adapter */
+ { USB_DEVICE(0x047d, 0x105d), .driver_info = BTUSB_RESET },
+ { USB_DEVICE(0x047d, 0x105e), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* ISSC Bluetooth Adapter v3.1 */
+ { USB_DEVICE(0x1131, 0x1001), .driver_info = BTUSB_RESET },
+
+ /* RTX Telecom based adapters with buggy SCO support */
+ { USB_DEVICE(0x0400, 0x0807), .driver_info = BTUSB_BROKEN_ISOC },
+ { USB_DEVICE(0x0400, 0x080a), .driver_info = BTUSB_BROKEN_ISOC },
+
+ /* CONWISE Technology based adapters with buggy SCO support */
+ { USB_DEVICE(0x0e5e, 0x6622), .driver_info = BTUSB_BROKEN_ISOC },
+
+ /* Belkin F8T012 and F8T013 devices */
+ { USB_DEVICE(0x050d, 0x0012), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+ { USB_DEVICE(0x050d, 0x0013), .driver_info = BTUSB_RESET | BTUSB_WRONG_SCO_MTU },
+
+ /* Digianswer devices */
+ { USB_DEVICE(0x08fd, 0x0001), .driver_info = BTUSB_DIGIANSWER },
+ { USB_DEVICE(0x08fd, 0x0002), .driver_info = BTUSB_IGNORE },
+
+ /* CSR BlueCore Bluetooth Sniffer */
+ { USB_DEVICE(0x0a12, 0x0002), .driver_info = BTUSB_SNIFFER },
+
+ /* Frontline ComProbe Bluetooth Sniffer */
+ { USB_DEVICE(0x16d3, 0x0002), .driver_info = BTUSB_SNIFFER },
+
{ } /* Terminating entry */
};
BT_DBG("intf %p id %p", intf, id);
+ /* interface numbers are hardcoded in the spec */
if (intf->cur_altsetting->desc.bInterfaceNumber != 0)
return -ENODEV;
id = match;
}
+ if (id->driver_info == BTUSB_IGNORE)
+ return -ENODEV;
+
+ if (ignore_dga && id->driver_info & BTUSB_DIGIANSWER)
+ return -ENODEV;
+
+ if (ignore_csr && id->driver_info & BTUSB_CSR)
+ return -ENODEV;
+
+ if (ignore_sniffer && id->driver_info & BTUSB_SNIFFER)
+ return -ENODEV;
+
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
hdev->owner = THIS_MODULE;
- set_bit(HCI_QUIRK_RESET_ON_INIT, &hdev->quirks);
+ if (reset || id->driver_info & BTUSB_RESET)
+ set_bit(HCI_QUIRK_RESET_ON_INIT, &hdev->quirks);
+
+ if (force_scofix || id->driver_info & BTUSB_WRONG_SCO_MTU) {
+ if (!disable_scofix)
+ set_bit(HCI_QUIRK_FIXUP_BUFFER_SIZE, &hdev->quirks);
+ }
+
+ if (id->driver_info & BTUSB_SNIFFER) {
+ struct usb_device *udev = interface_to_usbdev(intf);
+
+ if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x997)
+ set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
+ }
+
+ if (id->driver_info & BTUSB_BCM92035) {
+ unsigned char cmd[] = { 0x3b, 0xfc, 0x01, 0x00 };
+ struct sk_buff *skb;
+
+ skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
+ if (skb) {
+ memcpy(skb_put(skb, sizeof(cmd)), cmd, sizeof(cmd));
+ skb_queue_tail(&hdev->driver_init, skb);
+ }
+ }
err = hci_register_dev(hdev);
if (err < 0) {
module_init(btusb_init);
module_exit(btusb_exit);
+module_param(ignore_dga, bool, 0644);
+MODULE_PARM_DESC(ignore_dga, "Ignore devices with id 08fd:0001");
+
+module_param(ignore_csr, bool, 0644);
+MODULE_PARM_DESC(ignore_csr, "Ignore devices with id 0a12:0001");
+
+module_param(ignore_sniffer, bool, 0644);
+MODULE_PARM_DESC(ignore_sniffer, "Ignore devices with id 0a12:0002");
+
+module_param(disable_scofix, bool, 0644);
+MODULE_PARM_DESC(disable_scofix, "Disable fixup of wrong SCO buffer size");
+
+module_param(force_scofix, bool, 0644);
+MODULE_PARM_DESC(force_scofix, "Force fixup of wrong SCO buffers size");
+
+module_param(reset, bool, 0644);
+MODULE_PARM_DESC(reset, "Send HCI reset command on initialization");
+
MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
MODULE_DESCRIPTION("Generic Bluetooth USB driver ver " VERSION);
MODULE_VERSION(VERSION);
#define URB_ZERO_PACKET 0
#endif
-static int ignore;
static int ignore_dga;
static int ignore_csr;
static int ignore_sniffer;
static int isoc = 2;
#endif
-#define VERSION "2.9"
+#define VERSION "2.10"
static struct usb_driver hci_usb_driver;
/* Dell laptop with Broadcom chip */
{ USB_DEVICE(0x413c, 0x8126), .driver_info = HCI_RESET | HCI_WRONG_SCO_MTU },
+ /* Dell Wireless 370 */
+ { USB_DEVICE(0x413c, 0x8156), .driver_info = HCI_RESET | HCI_WRONG_SCO_MTU },
+ /* Dell Wireless 410 */
+ { USB_DEVICE(0x413c, 0x8152), .driver_info = HCI_RESET | HCI_WRONG_SCO_MTU },
+
+ /* Broadcom 2046 */
+ { USB_DEVICE(0x0a5c, 0x2151), .driver_info = HCI_RESET },
/* Microsoft Wireless Transceiver for Bluetooth 2.0 */
{ USB_DEVICE(0x045e, 0x009c), .driver_info = HCI_RESET },
id = match;
}
- if (ignore || id->driver_info & HCI_IGNORE)
+ if (id->driver_info & HCI_IGNORE)
return -ENODEV;
if (ignore_dga && id->driver_info & HCI_DIGIANSWER)
module_init(hci_usb_init);
module_exit(hci_usb_exit);
-module_param(ignore, bool, 0644);
-MODULE_PARM_DESC(ignore, "Ignore devices from the matching table");
-
module_param(ignore_dga, bool, 0644);
MODULE_PARM_DESC(ignore_dga, "Ignore devices with id 08fd:0001");
tracks->xa=0;
tracks->error=0;
cdinfo(CD_COUNT_TRACKS, "entering cdrom_count_tracks\n");
- if (!CDROM_CAN(CDC_PLAY_AUDIO)) {
- tracks->error=CDS_NO_INFO;
- return;
- }
/* Grab the TOC header so we can see how many tracks there are */
if ((ret = cdi->ops->audio_ioctl(cdi, CDROMREADTOCHDR, &header))) {
if (ret == -ENOMEDIUM)
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/delay.h>
-#include <asm/mach/dma.h>
-#include <asm/mach/sysasic.h>
+#include <mach/dma.h>
+#include <mach/sysasic.h>
#define GDROM_DEV_NAME "gdrom"
#define GD_SESSION_OFFSET 150
bool "Virtual terminal" if EMBEDDED
depends on !S390
select INPUT
- default y if !VIOCONS
+ default y
---help---
If you say Y here, you will get support for terminal devices with
display and keyboard devices. These are called "virtual" because you
obj-$(CONFIG_SGI_SNSC) += snsc.o snsc_event.o
obj-$(CONFIG_MSPEC) += mspec.o
obj-$(CONFIG_MMTIMER) += mmtimer.o
-obj-$(CONFIG_VIOCONS) += viocons.o
obj-$(CONFIG_VIOTAPE) += viotape.o
obj-$(CONFIG_HVCS) += hvcs.o
obj-$(CONFIG_IBM_BSR) += bsr.o
unsigned long flags;
if (serial_paranoia_check(info, tty->name, "rs_break"))
- return;
+ return -EINVAL;
local_irq_save(flags);
if (break_state == -1)
#include <linux/init.h>
#include <linux/smp_lock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/uaccess.h>
#include <asm/therm.h>
#include <linux/rtc.h>
#include <linux/proc_fs.h>
#include <linux/efi.h>
-#include <linux/smp_lock.h>
#include <linux/uaccess.h>
#include <asm/system.h>
* Ryan S. Arnold <rsa@us.ibm.com>
*
* hvc_console header information:
- * moved here from include/asm-powerpc/hvconsole.h
+ * moved here from arch/powerpc/include/asm/hvconsole.h
* and drivers/char/hvc_console.c
*
* This program is free software; you can redistribute it and/or modify
* the hvcs_final_close() function in order to get it out of the spinlock.
* Rearranged hvcs_close(). Cleaned up some printks and did some housekeeping
* on the changelog. Removed local CLC_LENGTH and used HVCS_CLC_LENGTH from
- * include/asm-powerpc/hvcserver.h
+ * arch/powerepc/include/asm/hvcserver.h
*
* 1.3.2 -> 1.3.3 Replaced yield() in hvcs_close() with tty_wait_until_sent() to
* prevent possible lockup with realtime scheduling as similarily pointed out by
#include <linux/hw_random.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static int ixp4xx_rng_data_read(struct hwrng *rng, u32 *buffer)
#include <linux/ctype.h>
#ifdef CONFIG_PPC_OF
-#include <asm/of_device.h>
-#include <asm/of_platform.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
#endif
#define PFX "ipmi_si: "
switch (cmd) {
case MOXA_GET_MAJOR:
- printk(KERN_WARNING "mxser: '%s' uses deprecated ioctl %x, fix "
- "your userspace\n", current->comm, cmd);
+ if (printk_ratelimit())
+ printk(KERN_WARNING "mxser: '%s' uses deprecated ioctl "
+ "%x (GET_MAJOR), fix your userspace\n",
+ current->comm, cmd);
return put_user(ttymajor, (int __user *)argp);
case MOXA_CHKPORTENABLE:
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
static int debug_level = 0;
static int maxframe[MAX_DEVICE_COUNT] = {0,};
-static int dosyncppp[MAX_DEVICE_COUNT] = {1,1,1,1};
module_param(break_on_load, bool, 0);
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
MODULE_LICENSE("GPL");
if (info->line < MAX_DEVICE_COUNT) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
mgslpc_device_count++;
/* generic HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
static int dma[MAX_ISA_DEVICES];
static int debug_level;
static int maxframe[MAX_TOTAL_DEVICES];
-static int dosyncppp[MAX_TOTAL_DEVICES];
static int txdmabufs[MAX_TOTAL_DEVICES];
static int txholdbufs[MAX_TOTAL_DEVICES];
module_param_array(dma, int, NULL, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
module_param_array(txdmabufs, int, NULL, 0);
module_param_array(txholdbufs, int, NULL, 0);
if (info->line < MAX_TOTAL_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
if (txdmabufs[info->line]) {
info->num_tx_dma_buffers = txdmabufs[info->line];
static int ttymajor;
static int debug_level;
static int maxframe[MAX_DEVICES];
-static int dosyncppp[MAX_DEVICES];
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
-MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
/*
* tty support and callbacks
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
struct net_device *netdev;
if (info->line < MAX_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
slgt_device_count++;
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
#if SYNCLINK_GENERIC_HDLC
*/
static int debug_level = 0;
static int maxframe[MAX_DEVICES] = {0,};
-static int dosyncppp[MAX_DEVICES] = {0,};
module_param(break_on_load, bool, 0);
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
static char *driver_name = "SyncLink MultiPort driver";
static char *driver_version = "$Revision: 4.38 $";
if (info->line < MAX_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
synclinkmp_device_count++;
if (disc < N_TTY || disc >= NR_LDISCS)
return -EINVAL;
err = tty_ldisc_try_get(disc, ld);
- if (err == -EAGAIN) {
+ if (err < 0) {
request_module("tty-ldisc-%d", disc);
err = tty_ldisc_try_get(disc, ld);
}
+++ /dev/null
-/* -*- linux-c -*-
- *
- * drivers/char/viocons.c
- *
- * iSeries Virtual Terminal
- *
- * Authors: Dave Boutcher <boutcher@us.ibm.com>
- * Ryan Arnold <ryanarn@us.ibm.com>
- * Colin Devilbiss <devilbis@us.ibm.com>
- * Stephen Rothwell
- *
- * (C) Copyright 2000, 2001, 2002, 2003, 2004 IBM Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) anyu later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software Foundation,
- * Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#include <linux/kernel.h>
-#include <linux/proc_fs.h>
-#include <linux/errno.h>
-#include <linux/vmalloc.h>
-#include <linux/mm.h>
-#include <linux/console.h>
-#include <linux/module.h>
-#include <asm/uaccess.h>
-#include <linux/init.h>
-#include <linux/wait.h>
-#include <linux/spinlock.h>
-#include <asm/ioctls.h>
-#include <linux/kd.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/sysrq.h>
-
-#include <asm/firmware.h>
-#include <asm/iseries/vio.h>
-#include <asm/iseries/hv_lp_event.h>
-#include <asm/iseries/hv_call_event.h>
-#include <asm/iseries/hv_lp_config.h>
-#include <asm/iseries/hv_call.h>
-
-#ifdef CONFIG_VT
-#error You must turn off CONFIG_VT to use CONFIG_VIOCONS
-#endif
-
-#define VIOTTY_MAGIC (0x0DCB)
-#define VTTY_PORTS 10
-
-#define VIOCONS_KERN_WARN KERN_WARNING "viocons: "
-#define VIOCONS_KERN_INFO KERN_INFO "viocons: "
-
-static DEFINE_SPINLOCK(consolelock);
-static DEFINE_SPINLOCK(consoleloglock);
-
-static int vio_sysrq_pressed;
-
-#define VIOCHAR_NUM_BUF 16
-
-/*
- * Our port information. We store a pointer to one entry in the
- * tty_driver_data
- */
-static struct port_info {
- int magic;
- struct tty_struct *tty;
- HvLpIndex lp;
- u8 vcons;
- u64 seq; /* sequence number of last HV send */
- u64 ack; /* last ack from HV */
-/*
- * When we get writes faster than we can send it to the partition,
- * buffer the data here. Note that used is a bit map of used buffers.
- * It had better have enough bits to hold VIOCHAR_NUM_BUF the bitops assume
- * it is a multiple of unsigned long
- */
- unsigned long used;
- u8 *buffer[VIOCHAR_NUM_BUF];
- int bufferBytes[VIOCHAR_NUM_BUF];
- int curbuf;
- int bufferOverflow;
- int overflowMessage;
-} port_info[VTTY_PORTS];
-
-#define viochar_is_console(pi) ((pi) == &port_info[0])
-#define viochar_port(pi) ((pi) - &port_info[0])
-
-static void initDataEvent(struct viocharlpevent *viochar, HvLpIndex lp);
-
-static struct tty_driver *viotty_driver;
-
-static void hvlog(char *fmt, ...)
-{
- int i;
- unsigned long flags;
- va_list args;
- static char buf[256];
-
- spin_lock_irqsave(&consoleloglock, flags);
- va_start(args, fmt);
- i = vscnprintf(buf, sizeof(buf) - 1, fmt, args);
- va_end(args);
- buf[i++] = '\r';
- HvCall_writeLogBuffer(buf, i);
- spin_unlock_irqrestore(&consoleloglock, flags);
-}
-
-static void hvlogOutput(const char *buf, int count)
-{
- unsigned long flags;
- int begin;
- int index;
- static const char cr = '\r';
-
- begin = 0;
- spin_lock_irqsave(&consoleloglock, flags);
- for (index = 0; index < count; index++) {
- if (buf[index] == '\n') {
- /*
- * Start right after the last '\n' or at the zeroth
- * array position and output the number of characters
- * including the newline.
- */
- HvCall_writeLogBuffer(&buf[begin], index - begin + 1);
- begin = index + 1;
- HvCall_writeLogBuffer(&cr, 1);
- }
- }
- if ((index - begin) > 0)
- HvCall_writeLogBuffer(&buf[begin], index - begin);
- spin_unlock_irqrestore(&consoleloglock, flags);
-}
-
-/*
- * Make sure we're pointing to a valid port_info structure. Shamelessly
- * plagerized from serial.c
- */
-static inline int viotty_paranoia_check(struct port_info *pi,
- char *name, const char *routine)
-{
- static const char *bad_pi_addr = VIOCONS_KERN_WARN
- "warning: bad address for port_info struct (%s) in %s\n";
- static const char *badmagic = VIOCONS_KERN_WARN
- "warning: bad magic number for port_info struct (%s) in %s\n";
-
- if ((pi < &port_info[0]) || (viochar_port(pi) > VTTY_PORTS)) {
- printk(bad_pi_addr, name, routine);
- return 1;
- }
- if (pi->magic != VIOTTY_MAGIC) {
- printk(badmagic, name, routine);
- return 1;
- }
- return 0;
-}
-
-/*
- * Add data to our pending-send buffers.
- *
- * NOTE: Don't use printk in here because it gets nastily recursive.
- * hvlog can be used to log to the hypervisor buffer
- */
-static int buffer_add(struct port_info *pi, const char *buf, size_t len)
-{
- size_t bleft;
- size_t curlen;
- const char *curbuf;
- int nextbuf;
-
- curbuf = buf;
- bleft = len;
- while (bleft > 0) {
- /*
- * If there is no space left in the current buffer, we have
- * filled everything up, so return. If we filled the previous
- * buffer we would already have moved to the next one.
- */
- if (pi->bufferBytes[pi->curbuf] == VIOCHAR_MAX_DATA) {
- hvlog ("\n\rviocons: No overflow buffer available for memcpy().\n");
- pi->bufferOverflow++;
- pi->overflowMessage = 1;
- break;
- }
-
- /*
- * Turn on the "used" bit for this buffer. If it's already on,
- * that's fine.
- */
- set_bit(pi->curbuf, &pi->used);
-
- /*
- * See if this buffer has been allocated. If not, allocate it.
- */
- if (pi->buffer[pi->curbuf] == NULL) {
- pi->buffer[pi->curbuf] =
- kmalloc(VIOCHAR_MAX_DATA, GFP_ATOMIC);
- if (pi->buffer[pi->curbuf] == NULL) {
- hvlog("\n\rviocons: kmalloc failed allocating spaces for buffer %d.",
- pi->curbuf);
- break;
- }
- }
-
- /* Figure out how much we can copy into this buffer. */
- if (bleft < (VIOCHAR_MAX_DATA - pi->bufferBytes[pi->curbuf]))
- curlen = bleft;
- else
- curlen = VIOCHAR_MAX_DATA - pi->bufferBytes[pi->curbuf];
-
- /* Copy the data into the buffer. */
- memcpy(pi->buffer[pi->curbuf] + pi->bufferBytes[pi->curbuf],
- curbuf, curlen);
-
- pi->bufferBytes[pi->curbuf] += curlen;
- curbuf += curlen;
- bleft -= curlen;
-
- /*
- * Now see if we've filled this buffer. If not then
- * we'll try to use it again later. If we've filled it
- * up then we'll advance the curbuf to the next in the
- * circular queue.
- */
- if (pi->bufferBytes[pi->curbuf] == VIOCHAR_MAX_DATA) {
- nextbuf = (pi->curbuf + 1) % VIOCHAR_NUM_BUF;
- /*
- * Move to the next buffer if it hasn't been used yet
- */
- if (test_bit(nextbuf, &pi->used) == 0)
- pi->curbuf = nextbuf;
- }
- }
- return len - bleft;
-}
-
-/*
- * Send pending data
- *
- * NOTE: Don't use printk in here because it gets nastily recursive.
- * hvlog can be used to log to the hypervisor buffer
- */
-static void send_buffers(struct port_info *pi)
-{
- HvLpEvent_Rc hvrc;
- int nextbuf;
- struct viocharlpevent *viochar;
- unsigned long flags;
-
- spin_lock_irqsave(&consolelock, flags);
-
- viochar = (struct viocharlpevent *)
- vio_get_event_buffer(viomajorsubtype_chario);
-
- /* Make sure we got a buffer */
- if (viochar == NULL) {
- hvlog("\n\rviocons: Can't get viochar buffer in sendBuffers().");
- spin_unlock_irqrestore(&consolelock, flags);
- return;
- }
-
- if (pi->used == 0) {
- hvlog("\n\rviocons: in sendbuffers(), but no buffers used.\n");
- vio_free_event_buffer(viomajorsubtype_chario, viochar);
- spin_unlock_irqrestore(&consolelock, flags);
- return;
- }
-
- /*
- * curbuf points to the buffer we're filling. We want to
- * start sending AFTER this one.
- */
- nextbuf = (pi->curbuf + 1) % VIOCHAR_NUM_BUF;
-
- /*
- * Loop until we find a buffer with the used bit on
- */
- while (test_bit(nextbuf, &pi->used) == 0)
- nextbuf = (nextbuf + 1) % VIOCHAR_NUM_BUF;
-
- initDataEvent(viochar, pi->lp);
-
- /*
- * While we have buffers with data, and our send window
- * is open, send them
- */
- while ((test_bit(nextbuf, &pi->used)) &&
- ((pi->seq - pi->ack) < VIOCHAR_WINDOW)) {
- viochar->len = pi->bufferBytes[nextbuf];
- viochar->event.xCorrelationToken = pi->seq++;
- viochar->event.xSizeMinus1 =
- offsetof(struct viocharlpevent, data) + viochar->len;
-
- memcpy(viochar->data, pi->buffer[nextbuf], viochar->len);
-
- hvrc = HvCallEvent_signalLpEvent(&viochar->event);
- if (hvrc) {
- /*
- * MUST unlock the spinlock before doing a printk
- */
- vio_free_event_buffer(viomajorsubtype_chario, viochar);
- spin_unlock_irqrestore(&consolelock, flags);
-
- printk(VIOCONS_KERN_WARN
- "error sending event! return code %d\n",
- (int)hvrc);
- return;
- }
-
- /*
- * clear the used bit, zero the number of bytes in
- * this buffer, and move to the next buffer
- */
- clear_bit(nextbuf, &pi->used);
- pi->bufferBytes[nextbuf] = 0;
- nextbuf = (nextbuf + 1) % VIOCHAR_NUM_BUF;
- }
-
- /*
- * If we have emptied all the buffers, start at 0 again.
- * this will re-use any allocated buffers
- */
- if (pi->used == 0) {
- pi->curbuf = 0;
-
- if (pi->overflowMessage)
- pi->overflowMessage = 0;
-
- if (pi->tty) {
- tty_wakeup(pi->tty);
- }
- }
-
- vio_free_event_buffer(viomajorsubtype_chario, viochar);
- spin_unlock_irqrestore(&consolelock, flags);
-}
-
-/*
- * Our internal writer. Gets called both from the console device and
- * the tty device. the tty pointer will be NULL if called from the console.
- * Return total number of bytes "written".
- *
- * NOTE: Don't use printk in here because it gets nastily recursive. hvlog
- * can be used to log to the hypervisor buffer
- */
-static int internal_write(struct port_info *pi, const char *buf, size_t len)
-{
- HvLpEvent_Rc hvrc;
- size_t bleft;
- size_t curlen;
- const char *curbuf;
- unsigned long flags;
- struct viocharlpevent *viochar;
-
- /*
- * Write to the hvlog of inbound data are now done prior to
- * calling internal_write() since internal_write() is only called in
- * the event that an lp event path is active, which isn't the case for
- * logging attempts prior to console initialization.
- *
- * If there is already data queued for this port, send it prior to
- * attempting to send any new data.
- */
- if (pi->used)
- send_buffers(pi);
-
- spin_lock_irqsave(&consolelock, flags);
-
- viochar = vio_get_event_buffer(viomajorsubtype_chario);
- if (viochar == NULL) {
- spin_unlock_irqrestore(&consolelock, flags);
- hvlog("\n\rviocons: Can't get vio buffer in internal_write().");
- return -EAGAIN;
- }
- initDataEvent(viochar, pi->lp);
-
- curbuf = buf;
- bleft = len;
-
- while ((bleft > 0) && (pi->used == 0) &&
- ((pi->seq - pi->ack) < VIOCHAR_WINDOW)) {
- if (bleft > VIOCHAR_MAX_DATA)
- curlen = VIOCHAR_MAX_DATA;
- else
- curlen = bleft;
-
- viochar->event.xCorrelationToken = pi->seq++;
- memcpy(viochar->data, curbuf, curlen);
- viochar->len = curlen;
- viochar->event.xSizeMinus1 =
- offsetof(struct viocharlpevent, data) + curlen;
-
- hvrc = HvCallEvent_signalLpEvent(&viochar->event);
- if (hvrc) {
- hvlog("viocons: error sending event! %d\n", (int)hvrc);
- goto out;
- }
- curbuf += curlen;
- bleft -= curlen;
- }
-
- /* If we didn't send it all, buffer as much of it as we can. */
- if (bleft > 0)
- bleft -= buffer_add(pi, curbuf, bleft);
-out:
- vio_free_event_buffer(viomajorsubtype_chario, viochar);
- spin_unlock_irqrestore(&consolelock, flags);
- return len - bleft;
-}
-
-static struct port_info *get_port_data(struct tty_struct *tty)
-{
- unsigned long flags;
- struct port_info *pi;
-
- spin_lock_irqsave(&consolelock, flags);
- if (tty) {
- pi = (struct port_info *)tty->driver_data;
- if (!pi || viotty_paranoia_check(pi, tty->name,
- "get_port_data")) {
- pi = NULL;
- }
- } else
- /*
- * If this is the console device, use the lp from
- * the first port entry
- */
- pi = &port_info[0];
- spin_unlock_irqrestore(&consolelock, flags);
- return pi;
-}
-
-/*
- * Initialize the common fields in a charLpEvent
- */
-static void initDataEvent(struct viocharlpevent *viochar, HvLpIndex lp)
-{
- struct HvLpEvent *hev = &viochar->event;
-
- memset(viochar, 0, sizeof(struct viocharlpevent));
-
- hev->flags = HV_LP_EVENT_VALID | HV_LP_EVENT_DEFERRED_ACK |
- HV_LP_EVENT_INT;
- hev->xType = HvLpEvent_Type_VirtualIo;
- hev->xSubtype = viomajorsubtype_chario | viochardata;
- hev->xSourceLp = HvLpConfig_getLpIndex();
- hev->xTargetLp = lp;
- hev->xSizeMinus1 = sizeof(struct viocharlpevent);
- hev->xSourceInstanceId = viopath_sourceinst(lp);
- hev->xTargetInstanceId = viopath_targetinst(lp);
-}
-
-/*
- * early console device write
- */
-static void viocons_write_early(struct console *co, const char *s, unsigned count)
-{
- hvlogOutput(s, count);
-}
-
-/*
- * console device write
- */
-static void viocons_write(struct console *co, const char *s, unsigned count)
-{
- int index;
- int begin;
- struct port_info *pi;
-
- static const char cr = '\r';
-
- /*
- * Check port data first because the target LP might be valid but
- * simply not active, in which case we want to hvlog the output.
- */
- pi = get_port_data(NULL);
- if (pi == NULL) {
- hvlog("\n\rviocons_write: unable to get port data.");
- return;
- }
-
- hvlogOutput(s, count);
-
- if (!viopath_isactive(pi->lp))
- return;
-
- /*
- * Any newline character found will cause a
- * carriage return character to be emitted as well.
- */
- begin = 0;
- for (index = 0; index < count; index++) {
- if (s[index] == '\n') {
- /*
- * Newline found. Print everything up to and
- * including the newline
- */
- internal_write(pi, &s[begin], index - begin + 1);
- begin = index + 1;
- /* Emit a carriage return as well */
- internal_write(pi, &cr, 1);
- }
- }
-
- /* If any characters left to write, write them now */
- if ((index - begin) > 0)
- internal_write(pi, &s[begin], index - begin);
-}
-
-/*
- * Work out the device associate with this console
- */
-static struct tty_driver *viocons_device(struct console *c, int *index)
-{
- *index = c->index;
- return viotty_driver;
-}
-
-/*
- * console device I/O methods
- */
-static struct console viocons_early = {
- .name = "viocons",
- .write = viocons_write_early,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-static struct console viocons = {
- .name = "viocons",
- .write = viocons_write,
- .device = viocons_device,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-/*
- * TTY Open method
- */
-static int viotty_open(struct tty_struct *tty, struct file *filp)
-{
- int port;
- unsigned long flags;
- struct port_info *pi;
-
- port = tty->index;
-
- if ((port < 0) || (port >= VTTY_PORTS))
- return -ENODEV;
-
- spin_lock_irqsave(&consolelock, flags);
-
- pi = &port_info[port];
- /* If some other TTY is already connected here, reject the open */
- if ((pi->tty) && (pi->tty != tty)) {
- spin_unlock_irqrestore(&consolelock, flags);
- printk(VIOCONS_KERN_WARN
- "attempt to open device twice from different ttys\n");
- return -EBUSY;
- }
- tty->driver_data = pi;
- pi->tty = tty;
- spin_unlock_irqrestore(&consolelock, flags);
-
- return 0;
-}
-
-/*
- * TTY Close method
- */
-static void viotty_close(struct tty_struct *tty, struct file *filp)
-{
- unsigned long flags;
- struct port_info *pi;
-
- spin_lock_irqsave(&consolelock, flags);
- pi = (struct port_info *)tty->driver_data;
-
- if (!pi || viotty_paranoia_check(pi, tty->name, "viotty_close")) {
- spin_unlock_irqrestore(&consolelock, flags);
- return;
- }
- if (tty->count == 1)
- pi->tty = NULL;
- spin_unlock_irqrestore(&consolelock, flags);
-}
-
-/*
- * TTY Write method
- */
-static int viotty_write(struct tty_struct *tty, const unsigned char *buf,
- int count)
-{
- struct port_info *pi;
-
- pi = get_port_data(tty);
- if (pi == NULL) {
- hvlog("\n\rviotty_write: no port data.");
- return -ENODEV;
- }
-
- if (viochar_is_console(pi))
- hvlogOutput(buf, count);
-
- /*
- * If the path to this LP is closed, don't bother doing anything more.
- * just dump the data on the floor and return count. For some reason
- * some user level programs will attempt to probe available tty's and
- * they'll attempt a viotty_write on an invalid port which maps to an
- * invalid target lp. If this is the case then ignore the
- * viotty_write call and, since the viopath isn't active to this
- * partition, return count.
- */
- if (!viopath_isactive(pi->lp))
- return count;
-
- return internal_write(pi, buf, count);
-}
-
-/*
- * TTY put_char method
- */
-static int viotty_put_char(struct tty_struct *tty, unsigned char ch)
-{
- struct port_info *pi;
-
- pi = get_port_data(tty);
- if (pi == NULL)
- return 0;
-
- /* This will append '\r' as well if the char is '\n' */
- if (viochar_is_console(pi))
- hvlogOutput(&ch, 1);
-
- if (viopath_isactive(pi->lp))
- internal_write(pi, &ch, 1);
- return 1;
-}
-
-/*
- * TTY write_room method
- */
-static int viotty_write_room(struct tty_struct *tty)
-{
- int i;
- int room = 0;
- struct port_info *pi;
- unsigned long flags;
-
- spin_lock_irqsave(&consolelock, flags);
- pi = (struct port_info *)tty->driver_data;
- if (!pi || viotty_paranoia_check(pi, tty->name, "viotty_write_room")) {
- spin_unlock_irqrestore(&consolelock, flags);
- return 0;
- }
-
- /* If no buffers are used, return the max size. */
- if (pi->used == 0) {
- spin_unlock_irqrestore(&consolelock, flags);
- return VIOCHAR_MAX_DATA * VIOCHAR_NUM_BUF;
- }
-
- /*
- * We retain the spinlock because we want to get an accurate
- * count and it can change on us between each operation if we
- * don't hold the spinlock.
- */
- for (i = 0; ((i < VIOCHAR_NUM_BUF) && (room < VIOCHAR_MAX_DATA)); i++)
- room += (VIOCHAR_MAX_DATA - pi->bufferBytes[i]);
- spin_unlock_irqrestore(&consolelock, flags);
-
- if (room > VIOCHAR_MAX_DATA)
- room = VIOCHAR_MAX_DATA;
- return room;
-}
-
-/*
- * TTY chars_in_buffer method
- */
-static int viotty_chars_in_buffer(struct tty_struct *tty)
-{
- return 0;
-}
-
-static int viotty_ioctl(struct tty_struct *tty, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- switch (cmd) {
- /*
- * the ioctls below read/set the flags usually shown in the leds
- * don't use them - they will go away without warning
- */
- case KDGETLED:
- case KDGKBLED:
- return put_user(0, (char *)arg);
-
- case KDSKBLED:
- return 0;
- }
- /* FIXME: WTF is this being called for ??? */
- lock_kernel();
- ret = n_tty_ioctl(tty, file, cmd, arg);
- unlock_kernel();
- return ret;
-}
-
-/*
- * Handle an open charLpEvent. Could be either interrupt or ack
- */
-static void vioHandleOpenEvent(struct HvLpEvent *event)
-{
- unsigned long flags;
- struct viocharlpevent *cevent = (struct viocharlpevent *)event;
- u8 port = cevent->virtual_device;
- struct port_info *pi;
- int reject = 0;
-
- if (hvlpevent_is_ack(event)) {
- if (port >= VTTY_PORTS)
- return;
-
- spin_lock_irqsave(&consolelock, flags);
- /* Got the lock, don't cause console output */
-
- pi = &port_info[port];
- if (event->xRc == HvLpEvent_Rc_Good) {
- pi->seq = pi->ack = 0;
- /*
- * This line allows connections from the primary
- * partition but once one is connected from the
- * primary partition nothing short of a reboot
- * of linux will allow access from the hosting
- * partition again without a required iSeries fix.
- */
- pi->lp = event->xTargetLp;
- }
-
- spin_unlock_irqrestore(&consolelock, flags);
- if (event->xRc != HvLpEvent_Rc_Good)
- printk(VIOCONS_KERN_WARN
- "handle_open_event: event->xRc == (%d).\n",
- event->xRc);
-
- if (event->xCorrelationToken != 0) {
- atomic_t *aptr= (atomic_t *)event->xCorrelationToken;
- atomic_set(aptr, 1);
- } else
- printk(VIOCONS_KERN_WARN
- "weird...got open ack without atomic\n");
- return;
- }
-
- /* This had better require an ack, otherwise complain */
- if (!hvlpevent_need_ack(event)) {
- printk(VIOCONS_KERN_WARN "viocharopen without ack bit!\n");
- return;
- }
-
- spin_lock_irqsave(&consolelock, flags);
- /* Got the lock, don't cause console output */
-
- /* Make sure this is a good virtual tty */
- if (port >= VTTY_PORTS) {
- event->xRc = HvLpEvent_Rc_SubtypeError;
- cevent->subtype_result_code = viorc_openRejected;
- /*
- * Flag state here since we can't printk while holding
- * a spinlock.
- */
- reject = 1;
- } else {
- pi = &port_info[port];
- if ((pi->lp != HvLpIndexInvalid) &&
- (pi->lp != event->xSourceLp)) {
- /*
- * If this is tty is already connected to a different
- * partition, fail.
- */
- event->xRc = HvLpEvent_Rc_SubtypeError;
- cevent->subtype_result_code = viorc_openRejected;
- reject = 2;
- } else {
- pi->lp = event->xSourceLp;
- event->xRc = HvLpEvent_Rc_Good;
- cevent->subtype_result_code = viorc_good;
- pi->seq = pi->ack = 0;
- reject = 0;
- }
- }
-
- spin_unlock_irqrestore(&consolelock, flags);
-
- if (reject == 1)
- printk(VIOCONS_KERN_WARN "open rejected: bad virtual tty.\n");
- else if (reject == 2)
- printk(VIOCONS_KERN_WARN
- "open rejected: console in exclusive use by another partition.\n");
-
- /* Return the acknowledgement */
- HvCallEvent_ackLpEvent(event);
-}
-
-/*
- * Handle a close charLpEvent. This should ONLY be an Interrupt because the
- * virtual console should never actually issue a close event to the hypervisor
- * because the virtual console never goes away. A close event coming from the
- * hypervisor simply means that there are no client consoles connected to the
- * virtual console.
- *
- * Regardless of the number of connections masqueraded on the other side of
- * the hypervisor ONLY ONE close event should be called to accompany the ONE
- * open event that is called. The close event should ONLY be called when NO
- * MORE connections (masqueraded or not) exist on the other side of the
- * hypervisor.
- */
-static void vioHandleCloseEvent(struct HvLpEvent *event)
-{
- unsigned long flags;
- struct viocharlpevent *cevent = (struct viocharlpevent *)event;
- u8 port = cevent->virtual_device;
-
- if (hvlpevent_is_int(event)) {
- if (port >= VTTY_PORTS) {
- printk(VIOCONS_KERN_WARN
- "close message from invalid virtual device.\n");
- return;
- }
-
- /* For closes, just mark the console partition invalid */
- spin_lock_irqsave(&consolelock, flags);
- /* Got the lock, don't cause console output */
-
- if (port_info[port].lp == event->xSourceLp)
- port_info[port].lp = HvLpIndexInvalid;
-
- spin_unlock_irqrestore(&consolelock, flags);
- printk(VIOCONS_KERN_INFO "close from %d\n", event->xSourceLp);
- } else
- printk(VIOCONS_KERN_WARN
- "got unexpected close acknowlegement\n");
-}
-
-/*
- * Handle a config charLpEvent. Could be either interrupt or ack
- */
-static void vioHandleConfig(struct HvLpEvent *event)
-{
- struct viocharlpevent *cevent = (struct viocharlpevent *)event;
-
- HvCall_writeLogBuffer(cevent->data, cevent->len);
-
- if (cevent->data[0] == 0x01)
- printk(VIOCONS_KERN_INFO "window resized to %d: %d: %d: %d\n",
- cevent->data[1], cevent->data[2],
- cevent->data[3], cevent->data[4]);
- else
- printk(VIOCONS_KERN_WARN "unknown config event\n");
-}
-
-/*
- * Handle a data charLpEvent.
- */
-static void vioHandleData(struct HvLpEvent *event)
-{
- struct tty_struct *tty;
- unsigned long flags;
- struct viocharlpevent *cevent = (struct viocharlpevent *)event;
- struct port_info *pi;
- int index;
- int num_pushed;
- u8 port = cevent->virtual_device;
-
- if (port >= VTTY_PORTS) {
- printk(VIOCONS_KERN_WARN "data on invalid virtual device %d\n",
- port);
- return;
- }
-
- /*
- * Hold the spinlock so that we don't take an interrupt that
- * changes tty between the time we fetch the port_info
- * pointer and the time we paranoia check.
- */
- spin_lock_irqsave(&consolelock, flags);
- pi = &port_info[port];
-
- /*
- * Change 05/01/2003 - Ryan Arnold: If a partition other than
- * the current exclusive partition tries to send us data
- * events then just drop them on the floor because we don't
- * want his stinking data. He isn't authorized to receive
- * data because he wasn't the first one to get the console,
- * therefore he shouldn't be allowed to send data either.
- * This will work without an iSeries fix.
- */
- if (pi->lp != event->xSourceLp) {
- spin_unlock_irqrestore(&consolelock, flags);
- return;
- }
-
- tty = pi->tty;
- if (tty == NULL) {
- spin_unlock_irqrestore(&consolelock, flags);
- printk(VIOCONS_KERN_WARN "no tty for virtual device %d\n",
- port);
- return;
- }
-
- if (tty->magic != TTY_MAGIC) {
- spin_unlock_irqrestore(&consolelock, flags);
- printk(VIOCONS_KERN_WARN "tty bad magic\n");
- return;
- }
-
- /*
- * Just to be paranoid, make sure the tty points back to this port
- */
- pi = (struct port_info *)tty->driver_data;
- if (!pi || viotty_paranoia_check(pi, tty->name, "vioHandleData")) {
- spin_unlock_irqrestore(&consolelock, flags);
- return;
- }
- spin_unlock_irqrestore(&consolelock, flags);
-
- /*
- * Change 07/21/2003 - Ryan Arnold: functionality added to
- * support sysrq utilizing ^O as the sysrq key. The sysrq
- * functionality will only work if built into the kernel and
- * then only if sysrq is enabled through the proc filesystem.
- */
- num_pushed = 0;
- for (index = 0; index < cevent->len; index++) {
- /*
- * Will be optimized away if !CONFIG_MAGIC_SYSRQ:
- */
- if (sysrq_on()) {
- /* 0x0f is the ascii character for ^O */
- if (cevent->data[index] == '\x0f') {
- vio_sysrq_pressed = 1;
- /*
- * continue because we don't want to add
- * the sysrq key into the data string.
- */
- continue;
- } else if (vio_sysrq_pressed) {
- handle_sysrq(cevent->data[index], tty);
- vio_sysrq_pressed = 0;
- /*
- * continue because we don't want to add
- * the sysrq sequence into the data string.
- */
- continue;
- }
- }
- /*
- * The sysrq sequence isn't included in this check if
- * sysrq is enabled and compiled into the kernel because
- * the sequence will never get inserted into the buffer.
- * Don't attempt to copy more data into the buffer than we
- * have room for because it would fail without indication.
- */
- if(tty_insert_flip_char(tty, cevent->data[index], TTY_NORMAL) == 0) {
- printk(VIOCONS_KERN_WARN "input buffer overflow!\n");
- break;
- }
- num_pushed++;
- }
-
- if (num_pushed)
- tty_flip_buffer_push(tty);
-}
-
-/*
- * Handle an ack charLpEvent.
- */
-static void vioHandleAck(struct HvLpEvent *event)
-{
- struct viocharlpevent *cevent = (struct viocharlpevent *)event;
- unsigned long flags;
- u8 port = cevent->virtual_device;
-
- if (port >= VTTY_PORTS) {
- printk(VIOCONS_KERN_WARN "data on invalid virtual device\n");
- return;
- }
-
- spin_lock_irqsave(&consolelock, flags);
- port_info[port].ack = event->xCorrelationToken;
- spin_unlock_irqrestore(&consolelock, flags);
-
- if (port_info[port].used)
- send_buffers(&port_info[port]);
-}
-
-/*
- * Handle charLpEvents and route to the appropriate routine
- */
-static void vioHandleCharEvent(struct HvLpEvent *event)
-{
- int charminor;
-
- if (event == NULL)
- return;
-
- charminor = event->xSubtype & VIOMINOR_SUBTYPE_MASK;
- switch (charminor) {
- case viocharopen:
- vioHandleOpenEvent(event);
- break;
- case viocharclose:
- vioHandleCloseEvent(event);
- break;
- case viochardata:
- vioHandleData(event);
- break;
- case viocharack:
- vioHandleAck(event);
- break;
- case viocharconfig:
- vioHandleConfig(event);
- break;
- default:
- if (hvlpevent_is_int(event) && hvlpevent_need_ack(event)) {
- event->xRc = HvLpEvent_Rc_InvalidSubtype;
- HvCallEvent_ackLpEvent(event);
- }
- }
-}
-
-/*
- * Send an open event
- */
-static int send_open(HvLpIndex remoteLp, void *sem)
-{
- return HvCallEvent_signalLpEventFast(remoteLp,
- HvLpEvent_Type_VirtualIo,
- viomajorsubtype_chario | viocharopen,
- HvLpEvent_AckInd_DoAck, HvLpEvent_AckType_ImmediateAck,
- viopath_sourceinst(remoteLp),
- viopath_targetinst(remoteLp),
- (u64)(unsigned long)sem, VIOVERSION << 16,
- 0, 0, 0, 0);
-}
-
-static const struct tty_operations serial_ops = {
- .open = viotty_open,
- .close = viotty_close,
- .write = viotty_write,
- .put_char = viotty_put_char,
- .write_room = viotty_write_room,
- .chars_in_buffer = viotty_chars_in_buffer,
- .ioctl = viotty_ioctl,
-};
-
-static int __init viocons_init2(void)
-{
- atomic_t wait_flag;
- int rc;
-
- if (!firmware_has_feature(FW_FEATURE_ISERIES))
- return -ENODEV;
-
- /* +2 for fudge */
- rc = viopath_open(HvLpConfig_getPrimaryLpIndex(),
- viomajorsubtype_chario, VIOCHAR_WINDOW + 2);
- if (rc)
- printk(VIOCONS_KERN_WARN "error opening to primary %d\n", rc);
-
- if (viopath_hostLp == HvLpIndexInvalid)
- vio_set_hostlp();
-
- /*
- * And if the primary is not the same as the hosting LP, open to the
- * hosting lp
- */
- if ((viopath_hostLp != HvLpIndexInvalid) &&
- (viopath_hostLp != HvLpConfig_getPrimaryLpIndex())) {
- printk(VIOCONS_KERN_INFO "open path to hosting (%d)\n",
- viopath_hostLp);
- rc = viopath_open(viopath_hostLp, viomajorsubtype_chario,
- VIOCHAR_WINDOW + 2); /* +2 for fudge */
- if (rc)
- printk(VIOCONS_KERN_WARN
- "error opening to partition %d: %d\n",
- viopath_hostLp, rc);
- }
-
- if (vio_setHandler(viomajorsubtype_chario, vioHandleCharEvent) < 0)
- printk(VIOCONS_KERN_WARN
- "error seting handler for console events!\n");
-
- /*
- * First, try to open the console to the hosting lp.
- * Wait on a semaphore for the response.
- */
- atomic_set(&wait_flag, 0);
- if ((viopath_isactive(viopath_hostLp)) &&
- (send_open(viopath_hostLp, (void *)&wait_flag) == 0)) {
- printk(VIOCONS_KERN_INFO "hosting partition %d\n",
- viopath_hostLp);
- while (atomic_read(&wait_flag) == 0)
- mb();
- atomic_set(&wait_flag, 0);
- }
-
- /*
- * If we don't have an active console, try the primary
- */
- if ((!viopath_isactive(port_info[0].lp)) &&
- (viopath_isactive(HvLpConfig_getPrimaryLpIndex())) &&
- (send_open(HvLpConfig_getPrimaryLpIndex(), (void *)&wait_flag)
- == 0)) {
- printk(VIOCONS_KERN_INFO "opening console to primary partition\n");
- while (atomic_read(&wait_flag) == 0)
- mb();
- }
-
- /* Initialize the tty_driver structure */
- viotty_driver = alloc_tty_driver(VTTY_PORTS);
- viotty_driver->owner = THIS_MODULE;
- viotty_driver->driver_name = "vioconsole";
- viotty_driver->name = "tty";
- viotty_driver->name_base = 1;
- viotty_driver->major = TTY_MAJOR;
- viotty_driver->minor_start = 1;
- viotty_driver->type = TTY_DRIVER_TYPE_CONSOLE;
- viotty_driver->subtype = 1;
- viotty_driver->init_termios = tty_std_termios;
- viotty_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_RESET_TERMIOS;
- tty_set_operations(viotty_driver, &serial_ops);
-
- if (tty_register_driver(viotty_driver)) {
- printk(VIOCONS_KERN_WARN "couldn't register console driver\n");
- put_tty_driver(viotty_driver);
- viotty_driver = NULL;
- }
-
- unregister_console(&viocons_early);
- register_console(&viocons);
-
- return 0;
-}
-
-static int __init viocons_init(void)
-{
- int i;
-
- if (!firmware_has_feature(FW_FEATURE_ISERIES))
- return -ENODEV;
-
- printk(VIOCONS_KERN_INFO "registering console\n");
- for (i = 0; i < VTTY_PORTS; i++) {
- port_info[i].lp = HvLpIndexInvalid;
- port_info[i].magic = VIOTTY_MAGIC;
- }
- HvCall_setLogBufferFormatAndCodepage(HvCall_LogBuffer_ASCII, 437);
- add_preferred_console("viocons", 0, NULL);
- register_console(&viocons_early);
- return 0;
-}
-
-console_initcall(viocons_init);
-module_init(viocons_init2);
ws.ws_col = vc->vc_cols;
ws.ws_ypixel = vc->vc_scan_lines;
- mutex_lock(&vc->vc_tty->termios_mutex);
spin_lock_irq(&vc->vc_tty->ctrl_lock);
if ((ws.ws_row != cws->ws_row || ws.ws_col != cws->ws_col))
pgrp = get_pid(vc->vc_tty->pgrp);
put_pid(pgrp);
}
*cws = ws;
- mutex_unlock(&vc->vc_tty->termios_mutex);
}
if (CON_IS_VISIBLE(vc))
policy->user_policy.min = policy->cpuinfo.min_freq;
policy->user_policy.max = policy->cpuinfo.max_freq;
+ blocking_notifier_call_chain(&cpufreq_policy_notifier_list,
+ CPUFREQ_START, policy);
+
#ifdef CONFIG_SMP
#ifdef CONFIG_HOTPLUG_CPU
#include <crypto/authenc.h>
#include <crypto/scatterwalk.h>
-#include <asm/arch/npe.h>
-#include <asm/arch/qmgr.h>
+#include <mach/npe.h>
+#include <mach/qmgr.h>
#define MAX_KEYLEN 32
/* write address into NextDescriptor field of last desc in chain */
to_ioat_desc(ioat_chan->used_desc.prev)->hw->next =
first->async_tx.phys;
- __list_splice(&new_chain, ioat_chan->used_desc.prev);
+ list_splice_tail(&new_chain, &ioat_chan->used_desc);
ioat_chan->dmacount += desc_count;
ioat_chan->pending += desc_count;
#include <linux/memory.h>
#include <linux/ioport.h>
-#include <asm/arch/adma.h>
+#include <mach/adma.h>
#define to_iop_adma_chan(chan) container_of(chan, struct iop_adma_chan, common)
#define to_iop_adma_device(dev) \
struct response *response = data;
struct client *client = response->client;
unsigned long flags;
+ struct fw_cdev_event_response *r = &response->response;
- if (length < response->response.length)
- response->response.length = length;
+ if (length < r->length)
+ r->length = length;
if (rcode == RCODE_COMPLETE)
- memcpy(response->response.data, payload,
- response->response.length);
+ memcpy(r->data, payload, r->length);
spin_lock_irqsave(&client->lock, flags);
list_del(&response->resource.link);
spin_unlock_irqrestore(&client->lock, flags);
- response->response.type = FW_CDEV_EVENT_RESPONSE;
- response->response.rcode = rcode;
- queue_event(client, &response->event, &response->response,
- sizeof(response->response) + response->response.length,
- NULL, 0);
+ r->type = FW_CDEV_EVENT_RESPONSE;
+ r->rcode = rcode;
+
+ /*
+ * In the case that sizeof(*r) doesn't align with the position of the
+ * data, and the read is short, preserve an extra copy of the data
+ * to stay compatible with a pre-2.6.27 bug. Since the bug is harmless
+ * for short reads and some apps depended on it, this is both safe
+ * and prudent for compatibility.
+ */
+ if (r->length <= sizeof(*r) - offsetof(typeof(*r), data))
+ queue_event(client, &response->event, r, sizeof(*r),
+ r->data, r->length);
+ else
+ queue_event(client, &response->event, r, sizeof(*r) + r->length,
+ NULL, 0);
}
static int ioctl_send_request(struct client *client, void *buffer)
if (ibft_addr)
reserve_bootmem(pos, PAGE_ALIGN(len), BOOTMEM_DEFAULT);
}
-EXPORT_SYMBOL_GPL(reserve_ibft_region);
int radeon_no_wb;
-MODULE_PARM_DESC(no_wb, "Disable AGP writeback for scratch registers\n");
+MODULE_PARM_DESC(no_wb, "Disable AGP writeback for scratch registers");
module_param_named(no_wb, radeon_no_wb, int, 0444);
static int dri_library_name(struct drm_device *dev, char *buf)
This driver can also be built as a module. If so, the module
will be called abituguru3.
+config SENSORS_AD7414
+ tristate "Analog Devices AD7414"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Analog Devices
+ AD7414 temperature monitoring chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad7414.
+
config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
depends on I2C && EXPERIMENTAL
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
- depends on I2C && EXPERIMENTAL
+ depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
tristate "National Semiconductor LM75 and compatibles"
depends on I2C
help
- If you say yes here you get support for National Semiconductor LM75
- sensor chips and clones: Dallas Semiconductor DS75 and DS1775 (in
- 9-bit precision mode), and TelCom (now Microchip) TCN75.
+ If you say yes here you get support for one common type of
+ temperature sensor chip, with models including:
+
+ - Dallas Semiconductor DS75 and DS1775
+ - Maxim MAX6625 and MAX6626
+ - Microchip MCP980x
+ - National Semiconductor LM75
+ - NXP's LM75A
+ - ST Microelectronics STDS75
+ - TelCom (now Microchip) TCN75
+ - Texas Instruments TMP100, TMP101, TMP75, TMP175, TMP275
+
+ This driver supports driver model based binding through board
+ specific I2C device tables.
- The DS75 and DS1775 in 10- to 12-bit precision modes will require
- a force module parameter. The driver will not handle the extra
- precision anyhow.
+ It also supports the "legacy" style of driver binding. To use
+ that with some chips which don't replicate LM75 quirks exactly,
+ you may need the "force" module parameter.
This driver can also be built as a module. If so, the module
will be called lm75.
select HWMON_VID
help
If you say yes here you get support for the hardware monitoring
- and fan control features of the SMSC DME1737 (and compatibles
- like the Asus A8000) and SCH311x Super-I/O chips.
+ and fan control features of the SMSC DME1737, SCH311x, SCH5027, and
+ Asus A8000 Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called dme1737.
obj-$(CONFIG_SENSORS_ABITUGURU) += abituguru.o
obj-$(CONFIG_SENSORS_ABITUGURU3)+= abituguru3.o
+obj-$(CONFIG_SENSORS_AD7414) += ad7414.o
obj-$(CONFIG_SENSORS_AD7418) += ad7418.o
obj-$(CONFIG_SENSORS_ADM1021) += adm1021.o
obj-$(CONFIG_SENSORS_ADM1025) += adm1025.o
--- /dev/null
+/*
+ * An hwmon driver for the Analog Devices AD7414
+ *
+ * Copyright 2006 Stefan Roese <sr at denx.de>, DENX Software Engineering
+ *
+ * Copyright (c) 2008 PIKA Technologies
+ * Sean MacLennan <smaclennan@pikatech.com>
+ *
+ * Copyright (c) 2008 Spansion Inc.
+ * Frank Edelhaeuser <frank.edelhaeuser at spansion.com>
+ * (converted to "new style" I2C driver model, removed checkpatch.pl warnings)
+ *
+ * Based on ad7418.c
+ * Copyright 2006 Tower Technologies, Alessandro Zummo <a.zummo at towertech.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+
+
+/* AD7414 registers */
+#define AD7414_REG_TEMP 0x00
+#define AD7414_REG_CONF 0x01
+#define AD7414_REG_T_HIGH 0x02
+#define AD7414_REG_T_LOW 0x03
+
+static u8 AD7414_REG_LIMIT[] = { AD7414_REG_T_HIGH, AD7414_REG_T_LOW };
+
+struct ad7414_data {
+ struct device *hwmon_dev;
+ struct mutex lock; /* atomic read data updates */
+ char valid; /* !=0 if following fields are valid */
+ unsigned long next_update; /* In jiffies */
+ s16 temp_input; /* Register values */
+ s8 temps[ARRAY_SIZE(AD7414_REG_LIMIT)];
+};
+
+/* REG: (0.25C/bit, two's complement) << 6 */
+static inline int ad7414_temp_from_reg(s16 reg)
+{
+ /* use integer division instead of equivalent right shift to
+ * guarantee arithmetic shift and preserve the sign
+ */
+ return ((int)reg / 64) * 250;
+}
+
+static inline int ad7414_read(struct i2c_client *client, u8 reg)
+{
+ if (reg == AD7414_REG_TEMP) {
+ int value = i2c_smbus_read_word_data(client, reg);
+ return (value < 0) ? value : swab16(value);
+ } else
+ return i2c_smbus_read_byte_data(client, reg);
+}
+
+static inline int ad7414_write(struct i2c_client *client, u8 reg, u8 value)
+{
+ return i2c_smbus_write_byte_data(client, reg, value);
+}
+
+struct ad7414_data *ad7414_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ad7414_data *data = i2c_get_clientdata(client);
+
+ mutex_lock(&data->lock);
+
+ if (time_after(jiffies, data->next_update) || !data->valid) {
+ int value, i;
+
+ dev_dbg(&client->dev, "starting ad7414 update\n");
+
+ value = ad7414_read(client, AD7414_REG_TEMP);
+ if (value < 0)
+ dev_dbg(&client->dev, "AD7414_REG_TEMP err %d\n",
+ value);
+ else
+ data->temp_input = value;
+
+ for (i = 0; i < ARRAY_SIZE(AD7414_REG_LIMIT); ++i) {
+ value = ad7414_read(client, AD7414_REG_LIMIT[i]);
+ if (value < 0)
+ dev_dbg(&client->dev, "AD7414 reg %d err %d\n",
+ AD7414_REG_LIMIT[i], value);
+ else
+ data->temps[i] = value;
+ }
+
+ data->next_update = jiffies + HZ + HZ / 2;
+ data->valid = 1;
+ }
+
+ mutex_unlock(&data->lock);
+
+ return data;
+}
+
+static ssize_t show_temp_input(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ad7414_data *data = ad7414_update_device(dev);
+ return sprintf(buf, "%d\n", ad7414_temp_from_reg(data->temp_input));
+}
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input, NULL, 0);
+
+static ssize_t show_max_min(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int index = to_sensor_dev_attr(attr)->index;
+ struct ad7414_data *data = ad7414_update_device(dev);
+ return sprintf(buf, "%d\n", data->temps[index] * 1000);
+}
+
+static ssize_t set_max_min(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ad7414_data *data = i2c_get_clientdata(client);
+ int index = to_sensor_dev_attr(attr)->index;
+ u8 reg = AD7414_REG_LIMIT[index];
+ long temp = simple_strtol(buf, NULL, 10);
+
+ temp = SENSORS_LIMIT(temp, -40000, 85000);
+ temp = (temp + (temp < 0 ? -500 : 500)) / 1000;
+
+ mutex_lock(&data->lock);
+ data->temps[index] = temp;
+ ad7414_write(client, reg, temp);
+ mutex_unlock(&data->lock);
+ return count;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
+ show_max_min, set_max_min, 0);
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO,
+ show_max_min, set_max_min, 1);
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ int bitnr = to_sensor_dev_attr(attr)->index;
+ struct ad7414_data *data = ad7414_update_device(dev);
+ int value = (data->temp_input >> bitnr) & 1;
+ return sprintf(buf, "%d\n", value);
+}
+
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 4);
+
+static struct attribute *ad7414_attributes[] = {
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp1_max.dev_attr.attr,
+ &sensor_dev_attr_temp1_min.dev_attr.attr,
+ &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group ad7414_group = {
+ .attrs = ad7414_attributes,
+};
+
+static int ad7414_probe(struct i2c_client *client,
+ const struct i2c_device_id *dev_id)
+{
+ struct ad7414_data *data;
+ int conf;
+ int err = 0;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_READ_WORD_DATA))
+ goto exit;
+
+ data = kzalloc(sizeof(struct ad7414_data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->lock);
+
+ dev_info(&client->dev, "chip found\n");
+
+ /* Make sure the chip is powered up. */
+ conf = i2c_smbus_read_byte_data(client, AD7414_REG_CONF);
+ if (conf < 0)
+ dev_warn(&client->dev,
+ "ad7414_probe unable to read config register.\n");
+ else {
+ conf &= ~(1 << 7);
+ i2c_smbus_write_byte_data(client, AD7414_REG_CONF, conf);
+ }
+
+ /* Register sysfs hooks */
+ err = sysfs_create_group(&client->dev.kobj, &ad7414_group);
+ if (err)
+ goto exit_free;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &ad7414_group);
+exit_free:
+ kfree(data);
+exit:
+ return err;
+}
+
+static int __devexit ad7414_remove(struct i2c_client *client)
+{
+ struct ad7414_data *data = i2c_get_clientdata(client);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &ad7414_group);
+ kfree(data);
+ return 0;
+}
+
+static const struct i2c_device_id ad7414_id[] = {
+ { "ad7414", 0 },
+ {}
+};
+
+static struct i2c_driver ad7414_driver = {
+ .driver = {
+ .name = "ad7414",
+ },
+ .probe = ad7414_probe,
+ .remove = __devexit_p(ad7414_remove),
+ .id_table = ad7414_id,
+};
+
+static int __init ad7414_init(void)
+{
+ return i2c_add_driver(&ad7414_driver);
+}
+module_init(ad7414_init);
+
+static void __exit ad7414_exit(void)
+{
+ i2c_del_driver(&ad7414_driver);
+}
+module_exit(ad7414_exit);
+
+MODULE_AUTHOR("Stefan Roese <sr at denx.de>, "
+ "Frank Edelhaeuser <frank.edelhaeuser at spansion.com>");
+
+MODULE_DESCRIPTION("AD7414 driver");
+MODULE_LICENSE("GPL");
#define ADT7473_REG_BASE_ADDR 0x20
#define ADT7473_REG_VOLT_BASE_ADDR 0x21
-#define ADT7473_REG_VOLT_MAX_ADDR 0x22
#define ADT7473_REG_VOLT_MIN_BASE_ADDR 0x46
-#define ADT7473_REG_VOLT_MIN_MAX_ADDR 0x49
#define ADT7473_REG_TEMP_BASE_ADDR 0x25
-#define ADT7473_REG_TEMP_MAX_ADDR 0x27
#define ADT7473_REG_TEMP_LIMITS_BASE_ADDR 0x4E
-#define ADT7473_REG_TEMP_LIMITS_MAX_ADDR 0x53
#define ADT7473_REG_TEMP_TMIN_BASE_ADDR 0x67
-#define ADT7473_REG_TEMP_TMIN_MAX_ADDR 0x69
#define ADT7473_REG_TEMP_TMAX_BASE_ADDR 0x6A
-#define ADT7473_REG_TEMP_TMAX_MAX_ADDR 0x6C
#define ADT7473_REG_FAN_BASE_ADDR 0x28
-#define ADT7473_REG_FAN_MAX_ADDR 0x2F
#define ADT7473_REG_FAN_MIN_BASE_ADDR 0x54
-#define ADT7473_REG_FAN_MIN_MAX_ADDR 0x5B
#define ADT7473_REG_PWM_BASE_ADDR 0x30
-#define ADT7473_REG_PWM_MAX_ADDR 0x32
#define ADT7473_REG_PWM_MIN_BASE_ADDR 0x64
-#define ADT7473_REG_PWM_MIN_MAX_ADDR 0x66
#define ADT7473_REG_PWM_MAX_BASE_ADDR 0x38
-#define ADT7473_REG_PWM_MAX_MAX_ADDR 0x3A
#define ADT7473_REG_PWM_BHVR_BASE_ADDR 0x5C
-#define ADT7473_REG_PWM_BHVR_MAX_ADDR 0x5E
#define ADT7473_PWM_BHVR_MASK 0xE0
#define ADT7473_PWM_BHVR_SHIFT 5
#define ADT7473_FAN4_ALARM 0x20
#define ADT7473_R1T_SHORT 0x40
#define ADT7473_R2T_SHORT 0x80
-#define ADT7473_REG_MAX_ADDR 0x80
#define ALARM2(x) ((x) << 8)
struct i2c_client *client = to_i2c_client(dev);
struct adt7473_data *data = i2c_get_clientdata(client);
int temp = simple_strtol(buf, NULL, 10);
- temp = temp && 0xFF;
mutex_lock(&data->lock);
- data->max_duty_at_overheat = temp;
+ data->max_duty_at_overheat = !!temp;
reg = i2c_smbus_read_byte_data(client, ADT7473_REG_CFG4);
if (temp)
reg |= ADT7473_CFG4_MAX_DUTY_AT_OVT;
/*
- * dme1737.c - Driver for the SMSC DME1737, Asus A8000, and SMSC SCH311x
- * Super-I/O chips integrated hardware monitoring features.
- * Copyright (c) 2007 Juerg Haefliger <juergh@gmail.com>
+ * dme1737.c - Driver for the SMSC DME1737, Asus A8000, SMSC SCH311x and
+ * SCH5027 Super-I/O chips integrated hardware monitoring features.
+ * Copyright (c) 2007, 2008 Juerg Haefliger <juergh@gmail.com>
*
* This driver is an I2C/ISA hybrid, meaning that it uses the I2C bus to access
- * the chip registers if a DME1737 (or A8000) is found and the ISA bus if a
- * SCH311x chip is found. Both types of chips have very similar hardware
+ * the chip registers if a DME1737, A8000, or SCH5027 is found and the ISA bus
+ * if a SCH311x chip is found. Both types of chips have very similar hardware
* monitoring capabilities but differ in the way they can be accessed.
*
* This program is free software; you can redistribute it and/or modify
module_param(force_id, ushort, 0);
MODULE_PARM_DESC(force_id, "Override the detected device ID");
+static int probe_all_addr;
+module_param(probe_all_addr, bool, 0);
+MODULE_PARM_DESC(probe_all_addr, "Include probing of non-standard LPC "
+ "addresses");
+
/* Addresses to scan */
static const unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END};
/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(dme1737);
+I2C_CLIENT_INSMOD_2(dme1737, sch5027);
+
+/* ISA chip types */
+enum isa_chips { sch311x = sch5027 + 1 };
/* ---------------------------------------------------------------------
* Registers
#define DME1737_VERSTEP 0x88
#define DME1737_VERSTEP_MASK 0xf8
#define SCH311X_DEVICE 0x8c
+#define SCH5027_VERSTEP 0x69
/* Length of ISA address segment */
#define DME1737_EXTENT 2
int valid; /* !=0 if following fields are valid */
unsigned long last_update; /* in jiffies */
unsigned long last_vbat; /* in jiffies */
+ enum chips type;
+ const int *in_nominal; /* pointer to IN_NOMINAL array */
u8 vid;
u8 pwm_rr_en;
};
/* Nominal voltage values */
-static const int IN_NOMINAL[] = {5000, 2250, 3300, 5000, 12000, 3300, 3300};
+static const int IN_NOMINAL_DME1737[] = {5000, 2250, 3300, 5000, 12000, 3300,
+ 3300};
+static const int IN_NOMINAL_SCH311x[] = {2500, 1500, 3300, 5000, 12000, 3300,
+ 3300};
+static const int IN_NOMINAL_SCH5027[] = {5000, 2250, 3300, 1125, 1125, 3300,
+ 3300};
+#define IN_NOMINAL(type) ((type) == sch311x ? IN_NOMINAL_SCH311x : \
+ (type) == sch5027 ? IN_NOMINAL_SCH5027 : \
+ IN_NOMINAL_DME1737)
/* Voltage input
* Voltage inputs have 16 bits resolution, limit values have 8 bits
* resolution. */
-static inline int IN_FROM_REG(int reg, int ix, int res)
+static inline int IN_FROM_REG(int reg, int nominal, int res)
{
- return (reg * IN_NOMINAL[ix] + (3 << (res - 3))) / (3 << (res - 2));
+ return (reg * nominal + (3 << (res - 3))) / (3 << (res - 2));
}
-static inline int IN_TO_REG(int val, int ix)
+static inline int IN_TO_REG(int val, int nominal)
{
- return SENSORS_LIMIT((val * 192 + IN_NOMINAL[ix] / 2) /
- IN_NOMINAL[ix], 0, 255);
+ return SENSORS_LIMIT((val * 192 + nominal / 2) / nominal, 0, 255);
}
/* Temperature input
/* Sample register contents every 1 sec */
if (time_after(jiffies, data->last_update + HZ) || !data->valid) {
- data->vid = dme1737_read(client, DME1737_REG_VID) & 0x3f;
+ if (data->type != sch5027) {
+ data->vid = dme1737_read(client, DME1737_REG_VID) &
+ 0x3f;
+ }
/* In (voltage) registers */
for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
DME1737_REG_TEMP_MIN(ix));
data->temp_max[ix] = dme1737_read(client,
DME1737_REG_TEMP_MAX(ix));
- data->temp_offset[ix] = dme1737_read(client,
- DME1737_REG_TEMP_OFFSET(ix));
+ if (data->type != sch5027) {
+ data->temp_offset[ix] = dme1737_read(client,
+ DME1737_REG_TEMP_OFFSET(ix));
+ }
}
/* In and temp LSB registers
data->zone_abs[ix] = dme1737_read(client,
DME1737_REG_ZONE_ABS(ix));
}
- for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) {
- data->zone_hyst[ix] = dme1737_read(client,
+ if (data->type != sch5027) {
+ for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) {
+ data->zone_hyst[ix] = dme1737_read(client,
DME1737_REG_ZONE_HYST(ix));
+ }
}
/* Alarm registers */
switch (fn) {
case SYS_IN_INPUT:
- res = IN_FROM_REG(data->in[ix], ix, 16);
+ res = IN_FROM_REG(data->in[ix], data->in_nominal[ix], 16);
break;
case SYS_IN_MIN:
- res = IN_FROM_REG(data->in_min[ix], ix, 8);
+ res = IN_FROM_REG(data->in_min[ix], data->in_nominal[ix], 8);
break;
case SYS_IN_MAX:
- res = IN_FROM_REG(data->in_max[ix], ix, 8);
+ res = IN_FROM_REG(data->in_max[ix], data->in_nominal[ix], 8);
break;
case SYS_IN_ALARM:
res = (data->alarms >> DME1737_BIT_ALARM_IN[ix]) & 0x01;
mutex_lock(&data->update_lock);
switch (fn) {
case SYS_IN_MIN:
- data->in_min[ix] = IN_TO_REG(val, ix);
+ data->in_min[ix] = IN_TO_REG(val, data->in_nominal[ix]);
dme1737_write(client, DME1737_REG_IN_MIN(ix),
data->in_min[ix]);
break;
case SYS_IN_MAX:
- data->in_max[ix] = IN_TO_REG(val, ix);
+ data->in_max[ix] = IN_TO_REG(val, data->in_nominal[ix]);
dme1737_write(client, DME1737_REG_IN_MAX(ix),
data->in_max[ix]);
break;
return sprintf(buf, "%d\n", res);
}
-static struct attribute *dme1737_attr_pwm[];
+static struct attribute *dme1737_pwm_chmod_attr[];
static void dme1737_chmod_file(struct device*, struct attribute*, mode_t);
static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
switch (val) {
case 0:
/* Change permissions of pwm[ix] to read-only */
- dme1737_chmod_file(dev, dme1737_attr_pwm[ix],
+ dme1737_chmod_file(dev, dme1737_pwm_chmod_attr[ix],
S_IRUGO);
/* Turn fan fully on */
data->pwm_config[ix] = PWM_EN_TO_REG(0,
dme1737_write(client, DME1737_REG_PWM_CONFIG(ix),
data->pwm_config[ix]);
/* Change permissions of pwm[ix] to read-writeable */
- dme1737_chmod_file(dev, dme1737_attr_pwm[ix],
+ dme1737_chmod_file(dev, dme1737_pwm_chmod_attr[ix],
S_IRUGO | S_IWUSR);
break;
case 2:
/* Change permissions of pwm[ix] to read-only */
- dme1737_chmod_file(dev, dme1737_attr_pwm[ix],
+ dme1737_chmod_file(dev, dme1737_pwm_chmod_attr[ix],
S_IRUGO);
/* Turn on auto mode using the saved zone channel
* assignment */
/* PWMs 5-6 */
#define SENSOR_DEVICE_ATTR_PWM_5TO6(ix) \
-static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO | S_IWUSR, \
+static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO, \
show_pwm, set_pwm, SYS_PWM, ix-1); \
-static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \
+static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO, \
show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \
static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \
show_pwm, NULL, SYS_PWM_ENABLE, ix-1)
static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); /* for ISA devices */
-#define SENSOR_DEV_ATTR_IN(ix) \
-&sensor_dev_attr_in##ix##_input.dev_attr.attr, \
-&sensor_dev_attr_in##ix##_min.dev_attr.attr, \
-&sensor_dev_attr_in##ix##_max.dev_attr.attr, \
-&sensor_dev_attr_in##ix##_alarm.dev_attr.attr
-
-/* These attributes are read-writeable only if the chip is *not* locked */
-#define SENSOR_DEV_ATTR_TEMP_LOCK(ix) \
-&sensor_dev_attr_temp##ix##_offset.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_TEMP(ix) \
-SENSOR_DEV_ATTR_TEMP_LOCK(ix), \
-&sensor_dev_attr_temp##ix##_input.dev_attr.attr, \
-&sensor_dev_attr_temp##ix##_min.dev_attr.attr, \
-&sensor_dev_attr_temp##ix##_max.dev_attr.attr, \
-&sensor_dev_attr_temp##ix##_alarm.dev_attr.attr, \
-&sensor_dev_attr_temp##ix##_fault.dev_attr.attr
-
-/* These attributes are read-writeable only if the chip is *not* locked */
-#define SENSOR_DEV_ATTR_ZONE_LOCK(ix) \
-&sensor_dev_attr_zone##ix##_auto_point1_temp_hyst.dev_attr.attr, \
-&sensor_dev_attr_zone##ix##_auto_point1_temp.dev_attr.attr, \
-&sensor_dev_attr_zone##ix##_auto_point2_temp.dev_attr.attr, \
-&sensor_dev_attr_zone##ix##_auto_point3_temp.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_ZONE(ix) \
-SENSOR_DEV_ATTR_ZONE_LOCK(ix), \
-&sensor_dev_attr_zone##ix##_auto_channels_temp.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_FAN_1TO4(ix) \
-&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_type.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_FAN_5TO6(ix) \
-&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \
-&sensor_dev_attr_fan##ix##_max.dev_attr.attr
-
-/* These attributes are read-writeable only if the chip is *not* locked */
-#define SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix) \
-&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_ramp_rate.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_auto_channels_zone.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_auto_pwm_min.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_auto_point1_pwm.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_PWM_1TO3(ix) \
-SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix), \
-&sensor_dev_attr_pwm##ix.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_auto_point2_pwm.dev_attr.attr
-
-/* These attributes are read-writeable only if the chip is *not* locked */
-#define SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix) \
-&sensor_dev_attr_pwm##ix.dev_attr.attr, \
-&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr
-
-#define SENSOR_DEV_ATTR_PWM_5TO6(ix) \
-SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix), \
-&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr
-
/* This struct holds all the attributes that are always present and need to be
* created unconditionally. The attributes that need modification of their
* permissions are created read-only and write permissions are added or removed
* on the fly when required */
static struct attribute *dme1737_attr[] ={
/* Voltages */
- SENSOR_DEV_ATTR_IN(0),
- SENSOR_DEV_ATTR_IN(1),
- SENSOR_DEV_ATTR_IN(2),
- SENSOR_DEV_ATTR_IN(3),
- SENSOR_DEV_ATTR_IN(4),
- SENSOR_DEV_ATTR_IN(5),
- SENSOR_DEV_ATTR_IN(6),
+ &sensor_dev_attr_in0_input.dev_attr.attr,
+ &sensor_dev_attr_in0_min.dev_attr.attr,
+ &sensor_dev_attr_in0_max.dev_attr.attr,
+ &sensor_dev_attr_in0_alarm.dev_attr.attr,
+ &sensor_dev_attr_in1_input.dev_attr.attr,
+ &sensor_dev_attr_in1_min.dev_attr.attr,
+ &sensor_dev_attr_in1_max.dev_attr.attr,
+ &sensor_dev_attr_in1_alarm.dev_attr.attr,
+ &sensor_dev_attr_in2_input.dev_attr.attr,
+ &sensor_dev_attr_in2_min.dev_attr.attr,
+ &sensor_dev_attr_in2_max.dev_attr.attr,
+ &sensor_dev_attr_in2_alarm.dev_attr.attr,
+ &sensor_dev_attr_in3_input.dev_attr.attr,
+ &sensor_dev_attr_in3_min.dev_attr.attr,
+ &sensor_dev_attr_in3_max.dev_attr.attr,
+ &sensor_dev_attr_in3_alarm.dev_attr.attr,
+ &sensor_dev_attr_in4_input.dev_attr.attr,
+ &sensor_dev_attr_in4_min.dev_attr.attr,
+ &sensor_dev_attr_in4_max.dev_attr.attr,
+ &sensor_dev_attr_in4_alarm.dev_attr.attr,
+ &sensor_dev_attr_in5_input.dev_attr.attr,
+ &sensor_dev_attr_in5_min.dev_attr.attr,
+ &sensor_dev_attr_in5_max.dev_attr.attr,
+ &sensor_dev_attr_in5_alarm.dev_attr.attr,
+ &sensor_dev_attr_in6_input.dev_attr.attr,
+ &sensor_dev_attr_in6_min.dev_attr.attr,
+ &sensor_dev_attr_in6_max.dev_attr.attr,
+ &sensor_dev_attr_in6_alarm.dev_attr.attr,
+ /* Temperatures */
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp1_min.dev_attr.attr,
+ &sensor_dev_attr_temp1_max.dev_attr.attr,
+ &sensor_dev_attr_temp1_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_fault.dev_attr.attr,
+ &sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_min.dev_attr.attr,
+ &sensor_dev_attr_temp2_max.dev_attr.attr,
+ &sensor_dev_attr_temp2_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_fault.dev_attr.attr,
+ &sensor_dev_attr_temp3_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_min.dev_attr.attr,
+ &sensor_dev_attr_temp3_max.dev_attr.attr,
+ &sensor_dev_attr_temp3_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_fault.dev_attr.attr,
+ /* Zones */
+ &sensor_dev_attr_zone1_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone1_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone1_auto_point3_temp.dev_attr.attr,
+ &sensor_dev_attr_zone1_auto_channels_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point3_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_channels_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point3_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_channels_temp.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group dme1737_group = {
+ .attrs = dme1737_attr,
+};
+
+/* The following struct holds misc attributes, which are not available in all
+ * chips. Their creation depends on the chip type which is determined during
+ * module load. */
+static struct attribute *dme1737_misc_attr[] = {
/* Temperatures */
- SENSOR_DEV_ATTR_TEMP(1),
- SENSOR_DEV_ATTR_TEMP(2),
- SENSOR_DEV_ATTR_TEMP(3),
+ &sensor_dev_attr_temp1_offset.dev_attr.attr,
+ &sensor_dev_attr_temp2_offset.dev_attr.attr,
+ &sensor_dev_attr_temp3_offset.dev_attr.attr,
/* Zones */
- SENSOR_DEV_ATTR_ZONE(1),
- SENSOR_DEV_ATTR_ZONE(2),
- SENSOR_DEV_ATTR_ZONE(3),
+ &sensor_dev_attr_zone1_auto_point1_temp_hyst.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point1_temp_hyst.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point1_temp_hyst.dev_attr.attr,
/* Misc */
&dev_attr_vrm.attr,
&dev_attr_cpu0_vid.attr,
NULL
};
-static const struct attribute_group dme1737_group = {
- .attrs = dme1737_attr,
+static const struct attribute_group dme1737_misc_group = {
+ .attrs = dme1737_misc_attr,
};
/* The following structs hold the PWM attributes, some of which are optional.
* Their creation depends on the chip configuration which is determined during
* module load. */
-static struct attribute *dme1737_attr_pwm1[] = {
- SENSOR_DEV_ATTR_PWM_1TO3(1),
+static struct attribute *dme1737_pwm1_attr[] = {
+ &sensor_dev_attr_pwm1.dev_attr.attr,
+ &sensor_dev_attr_pwm1_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm1_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm1_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm2[] = {
- SENSOR_DEV_ATTR_PWM_1TO3(2),
+static struct attribute *dme1737_pwm2_attr[] = {
+ &sensor_dev_attr_pwm2.dev_attr.attr,
+ &sensor_dev_attr_pwm2_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm2_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm2_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_point2_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm3[] = {
- SENSOR_DEV_ATTR_PWM_1TO3(3),
+static struct attribute *dme1737_pwm3_attr[] = {
+ &sensor_dev_attr_pwm3.dev_attr.attr,
+ &sensor_dev_attr_pwm3_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm3_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm3_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_point2_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm5[] = {
- SENSOR_DEV_ATTR_PWM_5TO6(5),
+static struct attribute *dme1737_pwm5_attr[] = {
+ &sensor_dev_attr_pwm5.dev_attr.attr,
+ &sensor_dev_attr_pwm5_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm5_enable.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm6[] = {
- SENSOR_DEV_ATTR_PWM_5TO6(6),
+static struct attribute *dme1737_pwm6_attr[] = {
+ &sensor_dev_attr_pwm6.dev_attr.attr,
+ &sensor_dev_attr_pwm6_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm6_enable.dev_attr.attr,
NULL
};
static const struct attribute_group dme1737_pwm_group[] = {
- { .attrs = dme1737_attr_pwm1 },
- { .attrs = dme1737_attr_pwm2 },
- { .attrs = dme1737_attr_pwm3 },
+ { .attrs = dme1737_pwm1_attr },
+ { .attrs = dme1737_pwm2_attr },
+ { .attrs = dme1737_pwm3_attr },
{ .attrs = NULL },
- { .attrs = dme1737_attr_pwm5 },
- { .attrs = dme1737_attr_pwm6 },
+ { .attrs = dme1737_pwm5_attr },
+ { .attrs = dme1737_pwm6_attr },
+};
+
+/* The following struct holds misc PWM attributes, which are not available in
+ * all chips. Their creation depends on the chip type which is determined
+ * during module load. */
+static struct attribute *dme1737_pwm_misc_attr[] = {
+ &sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr,
};
/* The following structs hold the fan attributes, some of which are optional.
* Their creation depends on the chip configuration which is determined during
* module load. */
-static struct attribute *dme1737_attr_fan1[] = {
- SENSOR_DEV_ATTR_FAN_1TO4(1),
+static struct attribute *dme1737_fan1_attr[] = {
+ &sensor_dev_attr_fan1_input.dev_attr.attr,
+ &sensor_dev_attr_fan1_min.dev_attr.attr,
+ &sensor_dev_attr_fan1_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan1_type.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_fan2[] = {
- SENSOR_DEV_ATTR_FAN_1TO4(2),
+static struct attribute *dme1737_fan2_attr[] = {
+ &sensor_dev_attr_fan2_input.dev_attr.attr,
+ &sensor_dev_attr_fan2_min.dev_attr.attr,
+ &sensor_dev_attr_fan2_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan2_type.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_fan3[] = {
- SENSOR_DEV_ATTR_FAN_1TO4(3),
+static struct attribute *dme1737_fan3_attr[] = {
+ &sensor_dev_attr_fan3_input.dev_attr.attr,
+ &sensor_dev_attr_fan3_min.dev_attr.attr,
+ &sensor_dev_attr_fan3_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan3_type.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_fan4[] = {
- SENSOR_DEV_ATTR_FAN_1TO4(4),
+static struct attribute *dme1737_fan4_attr[] = {
+ &sensor_dev_attr_fan4_input.dev_attr.attr,
+ &sensor_dev_attr_fan4_min.dev_attr.attr,
+ &sensor_dev_attr_fan4_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan4_type.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_fan5[] = {
- SENSOR_DEV_ATTR_FAN_5TO6(5),
+static struct attribute *dme1737_fan5_attr[] = {
+ &sensor_dev_attr_fan5_input.dev_attr.attr,
+ &sensor_dev_attr_fan5_min.dev_attr.attr,
+ &sensor_dev_attr_fan5_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan5_max.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_fan6[] = {
- SENSOR_DEV_ATTR_FAN_5TO6(6),
+static struct attribute *dme1737_fan6_attr[] = {
+ &sensor_dev_attr_fan6_input.dev_attr.attr,
+ &sensor_dev_attr_fan6_min.dev_attr.attr,
+ &sensor_dev_attr_fan6_alarm.dev_attr.attr,
+ &sensor_dev_attr_fan6_max.dev_attr.attr,
NULL
};
static const struct attribute_group dme1737_fan_group[] = {
- { .attrs = dme1737_attr_fan1 },
- { .attrs = dme1737_attr_fan2 },
- { .attrs = dme1737_attr_fan3 },
- { .attrs = dme1737_attr_fan4 },
- { .attrs = dme1737_attr_fan5 },
- { .attrs = dme1737_attr_fan6 },
+ { .attrs = dme1737_fan1_attr },
+ { .attrs = dme1737_fan2_attr },
+ { .attrs = dme1737_fan3_attr },
+ { .attrs = dme1737_fan4_attr },
+ { .attrs = dme1737_fan5_attr },
+ { .attrs = dme1737_fan6_attr },
};
-/* The permissions of all of the following attributes are changed to read-
+/* The permissions of the following zone attributes are changed to read-
* writeable if the chip is *not* locked. Otherwise they stay read-only. */
-static struct attribute *dme1737_attr_lock[] = {
- /* Temperatures */
- SENSOR_DEV_ATTR_TEMP_LOCK(1),
- SENSOR_DEV_ATTR_TEMP_LOCK(2),
- SENSOR_DEV_ATTR_TEMP_LOCK(3),
- /* Zones */
- SENSOR_DEV_ATTR_ZONE_LOCK(1),
- SENSOR_DEV_ATTR_ZONE_LOCK(2),
- SENSOR_DEV_ATTR_ZONE_LOCK(3),
+static struct attribute *dme1737_zone_chmod_attr[] = {
+ &sensor_dev_attr_zone1_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone1_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone1_auto_point3_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone2_auto_point3_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr,
+ &sensor_dev_attr_zone3_auto_point3_temp.dev_attr.attr,
NULL
};
-static const struct attribute_group dme1737_lock_group = {
- .attrs = dme1737_attr_lock,
+static const struct attribute_group dme1737_zone_chmod_group = {
+ .attrs = dme1737_zone_chmod_attr,
};
/* The permissions of the following PWM attributes are changed to read-
* writeable if the chip is *not* locked and the respective PWM is available.
* Otherwise they stay read-only. */
-static struct attribute *dme1737_attr_pwm1_lock[] = {
- SENSOR_DEV_ATTR_PWM_1TO3_LOCK(1),
+static struct attribute *dme1737_pwm1_chmod_attr[] = {
+ &sensor_dev_attr_pwm1_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm1_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm1_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm2_lock[] = {
- SENSOR_DEV_ATTR_PWM_1TO3_LOCK(2),
+static struct attribute *dme1737_pwm2_chmod_attr[] = {
+ &sensor_dev_attr_pwm2_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm2_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm2_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm3_lock[] = {
- SENSOR_DEV_ATTR_PWM_1TO3_LOCK(3),
+static struct attribute *dme1737_pwm3_chmod_attr[] = {
+ &sensor_dev_attr_pwm3_freq.dev_attr.attr,
+ &sensor_dev_attr_pwm3_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm3_ramp_rate.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_channels_zone.dev_attr.attr,
+ &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm5_lock[] = {
- SENSOR_DEV_ATTR_PWM_5TO6_LOCK(5),
+static struct attribute *dme1737_pwm5_chmod_attr[] = {
+ &sensor_dev_attr_pwm5.dev_attr.attr,
+ &sensor_dev_attr_pwm5_freq.dev_attr.attr,
NULL
};
-static struct attribute *dme1737_attr_pwm6_lock[] = {
- SENSOR_DEV_ATTR_PWM_5TO6_LOCK(6),
+static struct attribute *dme1737_pwm6_chmod_attr[] = {
+ &sensor_dev_attr_pwm6.dev_attr.attr,
+ &sensor_dev_attr_pwm6_freq.dev_attr.attr,
NULL
};
-static const struct attribute_group dme1737_pwm_lock_group[] = {
- { .attrs = dme1737_attr_pwm1_lock },
- { .attrs = dme1737_attr_pwm2_lock },
- { .attrs = dme1737_attr_pwm3_lock },
+static const struct attribute_group dme1737_pwm_chmod_group[] = {
+ { .attrs = dme1737_pwm1_chmod_attr },
+ { .attrs = dme1737_pwm2_chmod_attr },
+ { .attrs = dme1737_pwm3_chmod_attr },
{ .attrs = NULL },
- { .attrs = dme1737_attr_pwm5_lock },
- { .attrs = dme1737_attr_pwm6_lock },
+ { .attrs = dme1737_pwm5_chmod_attr },
+ { .attrs = dme1737_pwm6_chmod_attr },
};
/* Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the
* chip is not locked. Otherwise they are read-only. */
-static struct attribute *dme1737_attr_pwm[] = {
+static struct attribute *dme1737_pwm_chmod_attr[] = {
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_pwm2.dev_attr.attr,
&sensor_dev_attr_pwm3.dev_attr.attr,
if (data->has_pwm & (1 << ix)) {
sysfs_remove_group(&dev->kobj,
&dme1737_pwm_group[ix]);
+ if (data->type != sch5027 && ix < 3) {
+ sysfs_remove_file(&dev->kobj,
+ dme1737_pwm_misc_attr[ix]);
+ }
}
}
+ if (data->type != sch5027) {
+ sysfs_remove_group(&dev->kobj, &dme1737_misc_group);
+ }
+
sysfs_remove_group(&dev->kobj, &dme1737_group);
if (!data->client.driver) {
goto exit_remove;
}
+ /* Create misc sysfs attributes */
+ if ((data->type != sch5027) &&
+ (err = sysfs_create_group(&dev->kobj,
+ &dme1737_misc_group))) {
+ goto exit_remove;
+ }
+
/* Create fan sysfs attributes */
for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) {
if (data->has_fan & (1 << ix)) {
&dme1737_pwm_group[ix]))) {
goto exit_remove;
}
+ if (data->type != sch5027 && ix < 3 &&
+ (err = sysfs_create_file(&dev->kobj,
+ dme1737_pwm_misc_attr[ix]))) {
+ goto exit_remove;
+ }
}
}
dev_info(dev, "Device is locked. Some attributes "
"will be read-only.\n");
} else {
- /* Change permissions of standard attributes */
- dme1737_chmod_group(dev, &dme1737_lock_group,
+ /* Change permissions of zone sysfs attributes */
+ dme1737_chmod_group(dev, &dme1737_zone_chmod_group,
S_IRUGO | S_IWUSR);
- /* Change permissions of PWM attributes */
- for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_lock_group); ix++) {
+ /* Change permissions of misc sysfs attributes */
+ if (data->type != sch5027) {
+ dme1737_chmod_group(dev, &dme1737_misc_group,
+ S_IRUGO | S_IWUSR);
+ }
+
+ /* Change permissions of PWM sysfs attributes */
+ for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_chmod_group); ix++) {
if (data->has_pwm & (1 << ix)) {
dme1737_chmod_group(dev,
- &dme1737_pwm_lock_group[ix],
+ &dme1737_pwm_chmod_group[ix],
+ S_IRUGO | S_IWUSR);
+ if (data->type != sch5027 && ix < 3) {
+ dme1737_chmod_file(dev,
+ dme1737_pwm_misc_attr[ix],
S_IRUGO | S_IWUSR);
+ }
}
}
if ((data->has_pwm & (1 << ix)) &&
(PWM_EN_FROM_REG(data->pwm_config[ix]) == 1)) {
dme1737_chmod_file(dev,
- dme1737_attr_pwm[ix],
+ dme1737_pwm_chmod_attr[ix],
S_IRUGO | S_IWUSR);
}
}
int ix;
u8 reg;
+ /* Point to the right nominal voltages array */
+ data->in_nominal = IN_NOMINAL(data->type);
+
data->config = dme1737_read(client, DME1737_REG_CONFIG);
/* Inform if part is not monitoring/started */
if (!(data->config & 0x01)) {
data->pwm_acz[2] = 4; /* pwm3 -> zone3 */
/* Set VRM */
- data->vrm = vid_which_vrm();
+ if (data->type != sch5027) {
+ data->vrm = vid_which_vrm();
+ }
return 0;
}
dme1737_sio_enter(sio_cip);
/* Check device ID
- * The DME1737 can return either 0x78 or 0x77 as its device ID. */
+ * The DME1737 can return either 0x78 or 0x77 as its device ID.
+ * The SCH5027 returns 0x89 as its device ID. */
reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20);
- if (!(reg == 0x77 || reg == 0x78)) {
+ if (!(reg == 0x77 || reg == 0x78 || reg == 0x89)) {
err = -ENODEV;
goto exit;
}
company = dme1737_read(client, DME1737_REG_COMPANY);
verstep = dme1737_read(client, DME1737_REG_VERSTEP);
- if (!((company == DME1737_COMPANY_SMSC) &&
- ((verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP))) {
+ if (company == DME1737_COMPANY_SMSC &&
+ (verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP) {
+ kind = dme1737;
+ } else if (company == DME1737_COMPANY_SMSC &&
+ verstep == SCH5027_VERSTEP) {
+ kind = sch5027;
+ } else {
err = -ENODEV;
goto exit_kfree;
}
}
- kind = dme1737;
- name = "dme1737";
+ if (kind == sch5027) {
+ name = "sch5027";
+ } else {
+ kind = dme1737;
+ name = "dme1737";
+ }
+ data->type = kind;
/* Fill in the remaining client fields and put it into the global
* list */
goto exit_kfree;
}
- dev_info(dev, "Found a DME1737 chip at 0x%02x (rev 0x%02x).\n",
- client->addr, verstep);
+ dev_info(dev, "Found a %s chip at 0x%02x (rev 0x%02x).\n",
+ kind == sch5027 ? "SCH5027" : "DME1737", client->addr,
+ verstep);
/* Initialize the DME1737 chip */
if ((err = dme1737_init_device(dev))) {
client->addr = res->start;
platform_set_drvdata(pdev, data);
- company = dme1737_read(client, DME1737_REG_COMPANY);
- device = dme1737_read(client, DME1737_REG_DEVICE);
+ /* Skip chip detection if module is loaded with force_id parameter */
+ if (!force_id) {
+ company = dme1737_read(client, DME1737_REG_COMPANY);
+ device = dme1737_read(client, DME1737_REG_DEVICE);
- if (!((company == DME1737_COMPANY_SMSC) &&
- (device == SCH311X_DEVICE))) {
- err = -ENODEV;
- goto exit_kfree;
+ if (!((company == DME1737_COMPANY_SMSC) &&
+ (device == SCH311X_DEVICE))) {
+ err = -ENODEV;
+ goto exit_kfree;
+ }
}
+ data->type = sch311x;
/* Fill in the remaining client fields and initialize the mutex */
strlcpy(client->name, "sch311x", I2C_NAME_SIZE);
}
if (dme1737_isa_detect(0x2e, &addr) &&
- dme1737_isa_detect(0x4e, &addr)) {
+ dme1737_isa_detect(0x4e, &addr) &&
+ (!probe_all_addr ||
+ (dme1737_isa_detect(0x162e, &addr) &&
+ dme1737_isa_detect(0x164e, &addr)))) {
/* Return 0 if we didn't find an ISA device */
return 0;
}
static inline void superio_select(int base, int ld);
static inline void superio_exit(int base);
-static inline u16 fan_from_reg ( u16 reg );
-
struct f71882fg_data {
unsigned short addr;
struct device *hwmon_dev;
u8 temp_diode_open;
};
-static u8 f71882fg_read8(struct f71882fg_data *data, u8 reg);
-static u16 f71882fg_read16(struct f71882fg_data *data, u8 reg);
-static void f71882fg_write8(struct f71882fg_data *data, u8 reg, u8 val);
-
/* Sysfs in*/
static ssize_t show_in(struct device *dev, struct device_attribute *devattr,
char *buf);
/*
- hwmon-vid.c - VID/VRM/VRD voltage conversions
-
- Copyright (c) 2004 Rudolf Marek <r.marek@assembler.cz>
-
- Partly imported from i2c-vid.h of the lm_sensors project
- Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
- With assistance from Trent Piepho <xyzzy@speakeasy.org>
-
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
-
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
+ * hwmon-vid.c - VID/VRM/VRD voltage conversions
+ *
+ * Copyright (c) 2004 Rudolf Marek <r.marek@assembler.cz>
+ *
+ * Partly imported from i2c-vid.h of the lm_sensors project
+ * Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
+ * With assistance from Trent Piepho <xyzzy@speakeasy.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/hwmon-vid.h>
/*
- Common code for decoding VID pins.
-
- References:
-
- For VRM 8.4 to 9.1, "VRM x.y DC-DC Converter Design Guidelines",
- available at http://developer.intel.com/.
-
- For VRD 10.0 and up, "VRD x.y Design Guide",
- available at http://developer.intel.com/.
-
- AMD Opteron processors don't follow the Intel specifications.
- I'm going to "make up" 2.4 as the spec number for the Opterons.
- No good reason just a mnemonic for the 24x Opteron processor
- series.
-
- Opteron VID encoding is:
- 00000 = 1.550 V
- 00001 = 1.525 V
- . . . .
- 11110 = 0.800 V
- 11111 = 0.000 V (off)
-
- The 17 specification is in fact Intel Mobile Voltage Positioning -
- (IMVP-II). You can find more information in the datasheet of Max1718
- http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2452
-
- The 13 specification corresponds to the Intel Pentium M series. There
- doesn't seem to be any named specification for these. The conversion
- tables are detailed directly in the various Pentium M datasheets:
- http://www.intel.com/design/intarch/pentiumm/docs_pentiumm.htm
-
- The 14 specification corresponds to Intel Core series. There
- doesn't seem to be any named specification for these. The conversion
- tables are detailed directly in the various Pentium Core datasheets:
- http://www.intel.com/design/mobile/datashts/309221.htm
-
- The 110 (VRM 11) specification corresponds to Intel Conroe based series.
- http://www.intel.com/design/processor/applnots/313214.htm
-*/
-
-/* vrm is the VRM/VRD document version multiplied by 10.
- val is the 4-bit or more VID code.
- Returned value is in mV to avoid floating point in the kernel.
- Some VID have some bits in uV scale, this is rounded to mV */
+ * Common code for decoding VID pins.
+ *
+ * References:
+ *
+ * For VRM 8.4 to 9.1, "VRM x.y DC-DC Converter Design Guidelines",
+ * available at http://developer.intel.com/.
+ *
+ * For VRD 10.0 and up, "VRD x.y Design Guide",
+ * available at http://developer.intel.com/.
+ *
+ * AMD NPT 0Fh (Athlon64 & Opteron), AMD Publication 32559,
+ * http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
+ * Table 71. VID Code Voltages
+ * AMD Opteron processors don't follow the Intel specifications.
+ * I'm going to "make up" 2.4 as the spec number for the Opterons.
+ * No good reason just a mnemonic for the 24x Opteron processor
+ * series.
+ *
+ * The 17 specification is in fact Intel Mobile Voltage Positioning -
+ * (IMVP-II). You can find more information in the datasheet of Max1718
+ * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2452
+ *
+ * The 13 specification corresponds to the Intel Pentium M series. There
+ * doesn't seem to be any named specification for these. The conversion
+ * tables are detailed directly in the various Pentium M datasheets:
+ * http://www.intel.com/design/intarch/pentiumm/docs_pentiumm.htm
+ *
+ * The 14 specification corresponds to Intel Core series. There
+ * doesn't seem to be any named specification for these. The conversion
+ * tables are detailed directly in the various Pentium Core datasheets:
+ * http://www.intel.com/design/mobile/datashts/309221.htm
+ *
+ * The 110 (VRM 11) specification corresponds to Intel Conroe based series.
+ * http://www.intel.com/design/processor/applnots/313214.htm
+ */
+
+/*
+ * vrm is the VRM/VRD document version multiplied by 10.
+ * val is the 4-bit or more VID code.
+ * Returned value is in mV to avoid floating point in the kernel.
+ * Some VID have some bits in uV scale, this is rounded to mV.
+ */
int vid_from_reg(int val, u8 vrm)
{
int vid;
if (val < 0x02 || val > 0xb2)
return 0;
return((1600000 - (val - 2) * 6250 + 500) / 1000);
- case 24: /* Opteron processor */
- val &= 0x1f;
- return(val == 0x1f ? 0 : 1550 - val * 25);
+
+ case 24: /* AMD NPT 0Fh (Athlon64 & Opteron) */
+ val &= 0x3f;
+ return (val < 32) ? 1550 - 25 * val
+ : 775 - (25 * (val - 31)) / 2;
case 91: /* VRM 9.1 */
case 90: /* VRM 9.0 */
/*
- After this point is the code to automatically determine which
- VRM/VRD specification should be used depending on the CPU.
-*/
+ * After this point is the code to automatically determine which
+ * VRM/VRD specification should be used depending on the CPU.
+ */
struct vrm_model {
u8 vendor;
/* The IT8718F has the VID value in a different register, in Super-I/O
configuration space. */
#define IT87_REG_VID 0x0a
-/* Warning: register 0x0b is used for something completely different in
- new chips/revisions. I suspect only 16-bit tachometer mode will work
- for these. */
+/* The IT8705F and IT8712F earlier than revision 0x08 use register 0x0b
+ for fan divisors. Later IT8712F revisions must use 16-bit tachometer
+ mode. */
#define IT87_REG_FAN_DIV 0x0b
#define IT87_REG_FAN_16BIT 0x0c
struct it87_sio_data {
enum chips type;
/* Values read from Super-I/O config space */
+ u8 revision;
u8 vid_value;
};
struct it87_data {
struct device *hwmon_dev;
enum chips type;
+ u8 revision;
unsigned short addr;
const char *name;
u8 manual_pwm_ctl[3]; /* manual PWM value set by user */
};
+static inline int has_16bit_fans(const struct it87_data *data)
+{
+ /* IT8705F Datasheet 0.4.1, 3h == Version G.
+ IT8712F Datasheet 0.9.1, section 8.3.5 indicates 7h == Version I.
+ These are the first revisions with 16bit tachometer support. */
+ return (data->type == it87 && data->revision >= 0x03)
+ || (data->type == it8712 && data->revision >= 0x07)
+ || data->type == it8716
+ || data->type == it8718;
+}
static int it87_probe(struct platform_device *pdev);
static int __devexit it87_remove(struct platform_device *pdev);
}
err = 0;
+ sio_data->revision = superio_inb(DEVREV) & 0x0f;
pr_info("it87: Found IT%04xF chip at 0x%x, revision %d\n",
- chip_type, *address, superio_inb(DEVREV) & 0x0f);
+ chip_type, *address, sio_data->revision);
/* Read GPIO config and VID value from LDN 7 (GPIO) */
if (chip_type != IT8705F_DEVID) {
data->addr = res->start;
data->type = sio_data->type;
+ data->revision = sio_data->revision;
data->name = names[sio_data->type];
/* Now, we do the remaining detection. */
goto ERROR2;
/* Do not create fan files for disabled fans */
- if (data->type == it8716 || data->type == it8718) {
+ if (has_16bit_fans(data)) {
/* 16-bit tachometers */
if (data->has_fan & (1 << 0)) {
if ((err = device_create_file(dev,
data->has_fan = (data->fan_main_ctrl >> 4) & 0x07;
/* Set tachometers to 16-bit mode if needed */
- if (data->type == it8716 || data->type == it8718) {
+ if (has_16bit_fans(data)) {
tmp = it87_read_value(data, IT87_REG_FAN_16BIT);
if (~tmp & 0x07 & data->has_fan) {
dev_dbg(&pdev->dev,
it87_write_value(data, IT87_REG_FAN_16BIT,
tmp | 0x07);
}
- if (tmp & (1 << 4))
- data->has_fan |= (1 << 3); /* fan4 enabled */
- if (tmp & (1 << 5))
- data->has_fan |= (1 << 4); /* fan5 enabled */
+ /* IT8705F only supports three fans. */
+ if (data->type != it87) {
+ if (tmp & (1 << 4))
+ data->has_fan |= (1 << 3); /* fan4 enabled */
+ if (tmp & (1 << 5))
+ data->has_fan |= (1 << 4); /* fan5 enabled */
+ }
}
/* Set current fan mode registers and the default settings for the
data->fan[i] = it87_read_value(data,
IT87_REG_FAN[i]);
/* Add high byte if in 16-bit mode */
- if (data->type == it8716 || data->type == it8718) {
+ if (has_16bit_fans(data)) {
data->fan[i] |= it87_read_value(data,
IT87_REG_FANX[i]) << 8;
data->fan_min[i] |= it87_read_value(data,
}
/* Newer chips don't have clock dividers */
- if ((data->has_fan & 0x07) && data->type != it8716
- && data->type != it8718) {
+ if ((data->has_fan & 0x07) && !has_16bit_fans(data)) {
i = it87_read_value(data, IT87_REG_FAN_DIV);
data->fan_div[0] = i & 0x07;
data->fan_div[1] = (i >> 3) & 0x07;
data->fan_ctl = it87_read_value(data, IT87_REG_FAN_CTL);
data->sensor = it87_read_value(data, IT87_REG_TEMP_ENABLE);
- /* The 8705 does not have VID capability */
+ /* The 8705 does not have VID capability.
+ The 8718 does not use IT87_REG_VID for the same purpose. */
if (data->type == it8712 || data->type == it8716) {
data->vid = it87_read_value(data, IT87_REG_VID);
/* The older IT8712F revisions had only 5 VID pins,
#include "lm75.h"
-/* Addresses to scan */
+/*
+ * This driver handles the LM75 and compatible digital temperature sensors.
+ * Only types which are _not_ listed in I2C_CLIENT_INSMOD_*() need to be
+ * listed here. We start at 9 since I2C_CLIENT_INSMOD_*() currently allow
+ * definition of up to 8 chip types (plus zero).
+ */
+
+enum lm75_type { /* keep sorted in alphabetical order */
+ ds1775 = 9,
+ ds75,
+ /* lm75 -- in I2C_CLIENT_INSMOD_1() */
+ lm75a,
+ max6625,
+ max6626,
+ mcp980x,
+ stds75,
+ tcn75,
+ tmp100,
+ tmp101,
+ tmp175,
+ tmp275,
+ tmp75,
+};
+
+/* Addresses scanned by legacy style driver binding */
static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
-/* Insmod parameters */
+/* Insmod parameters (only for legacy style driver binding) */
I2C_CLIENT_INSMOD_1(lm75);
-/* Many LM75 constants specified below */
/* The LM75 registers */
#define LM75_REG_CONF 0x01
/* Each client has this additional data */
struct lm75_data {
- struct i2c_client client;
- struct device *hwmon_dev;
+ struct i2c_client *client;
+ struct device *hwmon_dev;
struct mutex update_lock;
- char valid; /* !=0 if following fields are valid */
+ u8 orig_conf;
+ char valid; /* !=0 if registers are valid */
unsigned long last_updated; /* In jiffies */
u16 temp[3]; /* Register values,
0 = input
2 = hyst */
};
-static int lm75_attach_adapter(struct i2c_adapter *adapter);
-static int lm75_detect(struct i2c_adapter *adapter, int address, int kind);
-static void lm75_init_client(struct i2c_client *client);
-static int lm75_detach_client(struct i2c_client *client);
static int lm75_read_value(struct i2c_client *client, u8 reg);
static int lm75_write_value(struct i2c_client *client, u8 reg, u16 value);
static struct lm75_data *lm75_update_device(struct device *dev);
-/* This is the driver that will be inserted */
-static struct i2c_driver lm75_driver = {
- .driver = {
- .name = "lm75",
- },
- .attach_adapter = lm75_attach_adapter,
- .detach_client = lm75_detach_client,
-};
+/*-----------------------------------------------------------------------*/
+
+/* sysfs attributes for hwmon */
static ssize_t show_temp(struct device *dev, struct device_attribute *da,
char *buf)
show_temp, set_temp, 2);
static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
-static int lm75_attach_adapter(struct i2c_adapter *adapter)
-{
- if (!(adapter->class & I2C_CLASS_HWMON))
- return 0;
- return i2c_probe(adapter, &addr_data, lm75_detect);
-}
-
static struct attribute *lm75_attributes[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
.attrs = lm75_attributes,
};
+/*-----------------------------------------------------------------------*/
+
+/* "New style" I2C driver binding -- following the driver model */
+
+static int
+lm75_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+ struct lm75_data *data;
+ int status;
+ u8 set_mask, clr_mask;
+ int new;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA))
+ return -EIO;
+
+ data = kzalloc(sizeof(struct lm75_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, data);
+
+ data->client = client;
+ mutex_init(&data->update_lock);
+
+ /* Set to LM75 resolution (9 bits, 1/2 degree C) and range.
+ * Then tweak to be more precise when appropriate.
+ */
+ set_mask = 0;
+ clr_mask = (1 << 0) /* continuous conversions */
+ | (1 << 6) | (1 << 5); /* 9-bit mode */
+
+ /* configure as specified */
+ status = lm75_read_value(client, LM75_REG_CONF);
+ if (status < 0) {
+ dev_dbg(&client->dev, "Can't read config? %d\n", status);
+ goto exit_free;
+ }
+ data->orig_conf = status;
+ new = status & ~clr_mask;
+ new |= set_mask;
+ if (status != new)
+ lm75_write_value(client, LM75_REG_CONF, new);
+ dev_dbg(&client->dev, "Config %02x\n", new);
+
+ /* Register sysfs hooks */
+ status = sysfs_create_group(&client->dev.kobj, &lm75_group);
+ if (status)
+ goto exit_free;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ status = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ dev_info(&client->dev, "%s: sensor '%s'\n",
+ data->hwmon_dev->bus_id, client->name);
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &lm75_group);
+exit_free:
+ i2c_set_clientdata(client, NULL);
+ kfree(data);
+ return status;
+}
+
+static int lm75_remove(struct i2c_client *client)
+{
+ struct lm75_data *data = i2c_get_clientdata(client);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &lm75_group);
+ lm75_write_value(client, LM75_REG_CONF, data->orig_conf);
+ i2c_set_clientdata(client, NULL);
+ kfree(data);
+ return 0;
+}
+
+static const struct i2c_device_id lm75_ids[] = {
+ { "ds1775", ds1775, },
+ { "ds75", ds75, },
+ { "lm75", lm75, },
+ { "lm75a", lm75a, },
+ { "max6625", max6625, },
+ { "max6626", max6626, },
+ { "mcp980x", mcp980x, },
+ { "stds75", stds75, },
+ { "tcn75", tcn75, },
+ { "tmp100", tmp100, },
+ { "tmp101", tmp101, },
+ { "tmp175", tmp175, },
+ { "tmp275", tmp275, },
+ { "tmp75", tmp75, },
+ { /* LIST END */ }
+};
+MODULE_DEVICE_TABLE(i2c, lm75_ids);
+
+static struct i2c_driver lm75_driver = {
+ .driver = {
+ .name = "lm75",
+ },
+ .probe = lm75_probe,
+ .remove = lm75_remove,
+ .id_table = lm75_ids,
+};
+
+/*-----------------------------------------------------------------------*/
+
+/* "Legacy" I2C driver binding */
+
+static struct i2c_driver lm75_legacy_driver;
+
/* This function is called by i2c_probe */
static int lm75_detect(struct i2c_adapter *adapter, int address, int kind)
{
int i;
struct i2c_client *new_client;
- struct lm75_data *data;
int err = 0;
- const char *name = "";
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_WORD_DATA))
goto exit;
- /* OK. For now, we presume we have a valid client. We now create the
- client structure, even though we cannot fill it completely yet.
- But it allows us to access lm75_{read,write}_value. */
- if (!(data = kzalloc(sizeof(struct lm75_data), GFP_KERNEL))) {
+ /* OK. For now, we presume we have a valid address. We create the
+ client structure, even though there may be no sensor present.
+ But it allows us to use i2c_smbus_read_*_data() calls. */
+ new_client = kzalloc(sizeof *new_client, GFP_KERNEL);
+ if (!new_client) {
err = -ENOMEM;
goto exit;
}
- new_client = &data->client;
- i2c_set_clientdata(new_client, data);
new_client->addr = address;
new_client->adapter = adapter;
- new_client->driver = &lm75_driver;
+ new_client->driver = &lm75_legacy_driver;
new_client->flags = 0;
/* Now, we do the remaining detection. There is no identification-
|| i2c_smbus_read_word_data(new_client, 5) != hyst
|| i2c_smbus_read_word_data(new_client, 6) != hyst
|| i2c_smbus_read_word_data(new_client, 7) != hyst)
- goto exit_free;
+ goto exit_free;
os = i2c_smbus_read_word_data(new_client, 3);
if (i2c_smbus_read_word_data(new_client, 4) != os
|| i2c_smbus_read_word_data(new_client, 5) != os
|| i2c_smbus_read_word_data(new_client, 6) != os
|| i2c_smbus_read_word_data(new_client, 7) != os)
- goto exit_free;
+ goto exit_free;
/* Unused bits */
if (conf & 0xe0)
- goto exit_free;
+ goto exit_free;
/* Addresses cycling */
for (i = 8; i < 0xff; i += 8)
goto exit_free;
}
- /* Determine the chip type - only one kind supported! */
- if (kind <= 0)
- kind = lm75;
-
- if (kind == lm75) {
- name = "lm75";
- }
-
- /* Fill in the remaining client fields and put it into the global list */
- strlcpy(new_client->name, name, I2C_NAME_SIZE);
- data->valid = 0;
- mutex_init(&data->update_lock);
+ /* NOTE: we treat "force=..." and "force_lm75=..." the same.
+ * Only new-style driver binding distinguishes chip types.
+ */
+ strlcpy(new_client->name, "lm75", I2C_NAME_SIZE);
/* Tell the I2C layer a new client has arrived */
- if ((err = i2c_attach_client(new_client)))
+ err = i2c_attach_client(new_client);
+ if (err)
goto exit_free;
- /* Initialize the LM75 chip */
- lm75_init_client(new_client);
-
- /* Register sysfs hooks */
- if ((err = sysfs_create_group(&new_client->dev.kobj, &lm75_group)))
+ err = lm75_probe(new_client, NULL);
+ if (err < 0)
goto exit_detach;
- data->hwmon_dev = hwmon_device_register(&new_client->dev);
- if (IS_ERR(data->hwmon_dev)) {
- err = PTR_ERR(data->hwmon_dev);
- goto exit_remove;
- }
-
return 0;
-exit_remove:
- sysfs_remove_group(&new_client->dev.kobj, &lm75_group);
exit_detach:
i2c_detach_client(new_client);
exit_free:
- kfree(data);
+ kfree(new_client);
exit:
return err;
}
+static int lm75_attach_adapter(struct i2c_adapter *adapter)
+{
+ if (!(adapter->class & I2C_CLASS_HWMON))
+ return 0;
+ return i2c_probe(adapter, &addr_data, lm75_detect);
+}
+
static int lm75_detach_client(struct i2c_client *client)
{
- struct lm75_data *data = i2c_get_clientdata(client);
- hwmon_device_unregister(data->hwmon_dev);
- sysfs_remove_group(&client->dev.kobj, &lm75_group);
+ lm75_remove(client);
i2c_detach_client(client);
- kfree(data);
+ kfree(client);
return 0;
}
+static struct i2c_driver lm75_legacy_driver = {
+ .driver = {
+ .name = "lm75_legacy",
+ },
+ .attach_adapter = lm75_attach_adapter,
+ .detach_client = lm75_detach_client,
+};
+
+/*-----------------------------------------------------------------------*/
+
+/* register access */
+
/* All registers are word-sized, except for the configuration register.
LM75 uses a high-byte first convention, which is exactly opposite to
the SMBus standard. */
return i2c_smbus_write_word_data(client, reg, swab16(value));
}
-static void lm75_init_client(struct i2c_client *client)
-{
- int reg;
-
- /* Enable if in shutdown mode */
- reg = lm75_read_value(client, LM75_REG_CONF);
- if (reg >= 0 && (reg & 0x01))
- lm75_write_value(client, LM75_REG_CONF, reg & 0xfe);
-}
-
static struct lm75_data *lm75_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
return data;
}
+/*-----------------------------------------------------------------------*/
+
+/* module glue */
+
static int __init sensors_lm75_init(void)
{
- return i2c_add_driver(&lm75_driver);
+ int status;
+
+ status = i2c_add_driver(&lm75_driver);
+ if (status < 0)
+ return status;
+
+ status = i2c_add_driver(&lm75_legacy_driver);
+ if (status < 0)
+ i2c_del_driver(&lm75_driver);
+
+ return status;
}
static void __exit sensors_lm75_exit(void)
{
+ i2c_del_driver(&lm75_legacy_driver);
i2c_del_driver(&lm75_driver);
}
/*
lm85.c - Part of lm_sensors, Linux kernel modules for hardware
monitoring
- Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
+ Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
Copyright (c) 2002, 2003 Philip Pokorny <ppokorny@penguincomputing.com>
Copyright (c) 2003 Margit Schubert-While <margitsw@t-online.de>
Copyright (c) 2004 Justin Thiessen <jthiessen@penguincomputing.com>
#define LM85_REG_TEMP_MAX(nr) (0x4f + (nr) * 2)
/* Fan speeds are LSB, MSB (2 bytes) */
-#define LM85_REG_FAN(nr) (0x28 + (nr) *2)
-#define LM85_REG_FAN_MIN(nr) (0x54 + (nr) *2)
+#define LM85_REG_FAN(nr) (0x28 + (nr) * 2)
+#define LM85_REG_FAN_MIN(nr) (0x54 + (nr) * 2)
#define LM85_REG_PWM(nr) (0x30 + (nr))
-#define ADT7463_REG_OPPOINT(nr) (0x33 + (nr))
-
-#define ADT7463_REG_TMIN_CTL1 0x36
-#define ADT7463_REG_TMIN_CTL2 0x37
-
-#define LM85_REG_DEVICE 0x3d
#define LM85_REG_COMPANY 0x3e
#define LM85_REG_VERSTEP 0x3f
/* These are the recognized values for the above regs */
-#define LM85_DEVICE_ADX 0x27
#define LM85_COMPANY_NATIONAL 0x01
#define LM85_COMPANY_ANALOG_DEV 0x41
-#define LM85_COMPANY_SMSC 0x5c
+#define LM85_COMPANY_SMSC 0x5c
#define LM85_VERSTEP_VMASK 0xf0
#define LM85_VERSTEP_GENERIC 0x60
#define LM85_VERSTEP_LM85C 0x60
#define LM85_REG_AFAN_CONFIG(nr) (0x5c + (nr))
#define LM85_REG_AFAN_RANGE(nr) (0x5f + (nr))
#define LM85_REG_AFAN_SPIKE1 0x62
-#define LM85_REG_AFAN_SPIKE2 0x63
#define LM85_REG_AFAN_MINPWM(nr) (0x64 + (nr))
#define LM85_REG_AFAN_LIMIT(nr) (0x67 + (nr))
#define LM85_REG_AFAN_CRITICAL(nr) (0x6a + (nr))
#define LM85_REG_AFAN_HYST1 0x6d
#define LM85_REG_AFAN_HYST2 0x6e
-#define LM85_REG_TACH_MODE 0x74
-#define LM85_REG_SPINUP_CTL 0x75
-
-#define ADM1027_REG_TEMP_OFFSET(nr) (0x70 + (nr))
-#define ADM1027_REG_CONFIG2 0x73
-#define ADM1027_REG_INTMASK1 0x74
-#define ADM1027_REG_INTMASK2 0x75
#define ADM1027_REG_EXTEND_ADC1 0x76
#define ADM1027_REG_EXTEND_ADC2 0x77
-#define ADM1027_REG_CONFIG3 0x78
-#define ADM1027_REG_FAN_PPR 0x7b
-
-#define ADT7463_REG_THERM 0x79
-#define ADT7463_REG_THERM_LIMIT 0x7A
#define EMC6D100_REG_ALARM3 0x7d
/* IN5, IN6 and IN7 */
-#define EMC6D100_REG_IN(nr) (0x70 + ((nr)-5))
-#define EMC6D100_REG_IN_MIN(nr) (0x73 + ((nr)-5) * 2)
-#define EMC6D100_REG_IN_MAX(nr) (0x74 + ((nr)-5) * 2)
+#define EMC6D100_REG_IN(nr) (0x70 + ((nr) - 5))
+#define EMC6D100_REG_IN_MIN(nr) (0x73 + ((nr) - 5) * 2)
+#define EMC6D100_REG_IN_MAX(nr) (0x74 + ((nr) - 5) * 2)
#define EMC6D102_REG_EXTEND_ADC1 0x85
#define EMC6D102_REG_EXTEND_ADC2 0x86
#define EMC6D102_REG_EXTEND_ADC3 0x87
#define EMC6D102_REG_EXTEND_ADC4 0x88
-/* Conversions. Rounding and limit checking is only done on the TO_REG
+/* Conversions. Rounding and limit checking is only done on the TO_REG
variants. Note that you should be a bit careful with which arguments
these macros are called: arguments may be evaluated more than once.
*/
/* IN are scaled acording to built-in resistors */
-static int lm85_scaling[] = { /* .001 Volts */
- 2500, 2250, 3300, 5000, 12000,
- 3300, 1500, 1800 /*EMC6D100*/
- };
-#define SCALE(val,from,to) (((val)*(to) + ((from)/2))/(from))
+static const int lm85_scaling[] = { /* .001 Volts */
+ 2500, 2250, 3300, 5000, 12000,
+ 3300, 1500, 1800 /*EMC6D100*/
+};
+#define SCALE(val, from, to) (((val) * (to) + ((from) / 2)) / (from))
-#define INS_TO_REG(n,val) \
- SENSORS_LIMIT(SCALE(val,lm85_scaling[n],192),0,255)
+#define INS_TO_REG(n, val) \
+ SENSORS_LIMIT(SCALE(val, lm85_scaling[n], 192), 0, 255)
-#define INSEXT_FROM_REG(n,val,ext) \
+#define INSEXT_FROM_REG(n, val, ext) \
SCALE(((val) << 4) + (ext), 192 << 4, lm85_scaling[n])
-#define INS_FROM_REG(n,val) SCALE((val), 192, lm85_scaling[n])
+#define INS_FROM_REG(n, val) SCALE((val), 192, lm85_scaling[n])
/* FAN speed is measured using 90kHz clock */
static inline u16 FAN_TO_REG(unsigned long val)
return 0xffff;
return SENSORS_LIMIT(5400000 / val, 1, 0xfffe);
}
-#define FAN_FROM_REG(val) ((val)==0?-1:(val)==0xffff?0:5400000/(val))
+#define FAN_FROM_REG(val) ((val) == 0 ? -1 : (val) == 0xffff ? 0 : \
+ 5400000 / (val))
/* Temperature is reported in .001 degC increments */
#define TEMP_TO_REG(val) \
- SENSORS_LIMIT(SCALE(val,1000,1),-127,127)
-#define TEMPEXT_FROM_REG(val,ext) \
+ SENSORS_LIMIT(SCALE(val, 1000, 1), -127, 127)
+#define TEMPEXT_FROM_REG(val, ext) \
SCALE(((val) << 4) + (ext), 16, 1000)
#define TEMP_FROM_REG(val) ((val) * 1000)
-#define PWM_TO_REG(val) (SENSORS_LIMIT(val,0,255))
+#define PWM_TO_REG(val) SENSORS_LIMIT(val, 0, 255)
#define PWM_FROM_REG(val) (val)
*/
/* These are the zone temperature range encodings in .001 degree C */
-static int lm85_range_map[] = {
- 2000, 2500, 3300, 4000, 5000, 6600,
- 8000, 10000, 13300, 16000, 20000, 26600,
- 32000, 40000, 53300, 80000
- };
-static int RANGE_TO_REG( int range )
+static const int lm85_range_map[] = {
+ 2000, 2500, 3300, 4000, 5000, 6600, 8000, 10000,
+ 13300, 16000, 20000, 26600, 32000, 40000, 53300, 80000
+};
+
+static int RANGE_TO_REG(int range)
{
int i;
if (range >= lm85_range_map[15])
- return 15 ;
+ return 15;
/* Find the closest match */
for (i = 14; i >= 0; --i) {
return 0;
}
-#define RANGE_FROM_REG(val) (lm85_range_map[(val)&0x0f])
+#define RANGE_FROM_REG(val) lm85_range_map[(val) & 0x0f]
-/* These are the Acoustic Enhancement, or Temperature smoothing encodings
- * NOTE: The enable/disable bit is INCLUDED in these encodings as the
- * MSB (bit 3, value 8). If the enable bit is 0, the encoded value
- * is ignored, or set to 0.
- */
/* These are the PWM frequency encodings */
-static int lm85_freq_map[] = { /* .1 Hz */
- 100, 150, 230, 300, 380, 470, 620, 940
- };
-static int FREQ_TO_REG( int freq )
+static const int lm85_freq_map[] = { /* .1 Hz */
+ 100, 150, 230, 300, 380, 470, 620, 940
+};
+
+static int FREQ_TO_REG(int freq)
{
int i;
- if( freq >= lm85_freq_map[7] ) { return 7 ; }
- for( i = 0 ; i < 7 ; ++i )
- if( freq <= lm85_freq_map[i] )
- break ;
- return( i & 0x07 );
+ if (freq >= lm85_freq_map[7])
+ return 7;
+ for (i = 0; i < 7; ++i)
+ if (freq <= lm85_freq_map[i])
+ break;
+ return i;
}
-#define FREQ_FROM_REG(val) (lm85_freq_map[(val)&0x07])
+#define FREQ_FROM_REG(val) lm85_freq_map[(val) & 0x07]
/* Since we can't use strings, I'm abusing these numbers
* to stand in for the following meanings:
* -2 -- PWM responds to manual control
*/
-static int lm85_zone_map[] = { 1, 2, 3, -1, 0, 23, 123, -2 };
-#define ZONE_FROM_REG(val) (lm85_zone_map[((val)>>5)&0x07])
+static const int lm85_zone_map[] = { 1, 2, 3, -1, 0, 23, 123, -2 };
+#define ZONE_FROM_REG(val) lm85_zone_map[(val) >> 5]
-static int ZONE_TO_REG( int zone )
+static int ZONE_TO_REG(int zone)
{
int i;
- for( i = 0 ; i <= 7 ; ++i )
- if( zone == lm85_zone_map[i] )
- break ;
- if( i > 7 ) /* Not found. */
+ for (i = 0; i <= 7; ++i)
+ if (zone == lm85_zone_map[i])
+ break;
+ if (i > 7) /* Not found. */
i = 3; /* Always 100% */
- return( (i & 0x07)<<5 );
+ return i << 5;
}
-#define HYST_TO_REG(val) (SENSORS_LIMIT(((val)+500)/1000,0,15))
-#define HYST_FROM_REG(val) ((val)*1000)
-
-#define OFFSET_TO_REG(val) (SENSORS_LIMIT((val)/25,-127,127))
-#define OFFSET_FROM_REG(val) ((val)*25)
-
-#define PPR_MASK(fan) (0x03<<(fan *2))
-#define PPR_TO_REG(val,fan) (SENSORS_LIMIT((val)-1,0,3)<<(fan *2))
-#define PPR_FROM_REG(val,fan) ((((val)>>(fan * 2))&0x03)+1)
+#define HYST_TO_REG(val) SENSORS_LIMIT(((val) + 500) / 1000, 0, 15)
+#define HYST_FROM_REG(val) ((val) * 1000)
/* Chip sampling rates
*
u8 hyst; /* Low limit hysteresis. (0-15) */
u8 range; /* Temp range, encoded */
s8 critical; /* "All fans ON" temp limit */
- u8 off_desired; /* Actual "off" temperature specified. Preserved
+ u8 off_desired; /* Actual "off" temperature specified. Preserved
* to prevent "drift" as other autofan control
* values change.
*/
- u8 max_desired; /* Actual "max" temperature specified. Preserved
+ u8 max_desired; /* Actual "max" temperature specified. Preserved
* to prevent "drift" as other autofan control
* values change.
*/
s8 temp[3]; /* Register value */
s8 temp_min[3]; /* Register value */
s8 temp_max[3]; /* Register value */
- s8 temp_offset[3]; /* Register value */
u16 fan[4]; /* Register value */
u16 fan_min[4]; /* Register value */
u8 pwm[3]; /* Register value */
- u8 spinup_ctl; /* Register encoding, combined */
- u8 tach_mode; /* Register encoding, combined */
u8 temp_ext[3]; /* Decoded values */
u8 in_ext[8]; /* Decoded values */
- u8 fan_ppr; /* Register value */
- u8 smooth[3]; /* Register encoding */
u8 vid; /* Register value */
u8 vrm; /* VRM version */
- u8 syncpwm3; /* Saved PWM3 for TACH 2,3,4 config */
- u8 oppoint[3]; /* Register value */
- u16 tmin_ctl; /* Register value */
- unsigned long therm_total; /* Cummulative therm count */
- u8 therm_limit; /* Register value */
u32 alarms; /* Register encoding, combined */
struct lm85_autofan autofan[3];
struct lm85_zone zone[3];
static int lm85_detach_client(struct i2c_client *client);
static int lm85_read_value(struct i2c_client *client, u8 reg);
-static int lm85_write_value(struct i2c_client *client, u8 reg, int value);
+static void lm85_write_value(struct i2c_client *client, u8 reg, int value);
static struct lm85_data *lm85_update_device(struct device *dev);
-static void lm85_init_client(struct i2c_client *client);
static struct i2c_driver lm85_driver = {
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan[nr]) );
+ return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr]));
}
static ssize_t show_fan_min(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", FAN_FROM_REG(data->fan_min[nr]) );
+ return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan_min[nr]));
}
static ssize_t set_fan_min(struct device *dev, struct device_attribute *attr,
/* vid, vrm, alarms */
-static ssize_t show_vid_reg(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_vid_reg(struct device *dev, struct device_attribute *attr,
+ char *buf)
{
struct lm85_data *data = lm85_update_device(dev);
int vid;
static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL);
-static ssize_t show_vrm_reg(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_vrm_reg(struct device *dev, struct device_attribute *attr,
+ char *buf)
{
struct lm85_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%ld\n", (long) data->vrm);
}
-static ssize_t store_vrm_reg(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
+static ssize_t store_vrm_reg(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
{
struct lm85_data *data = dev_get_drvdata(dev);
data->vrm = simple_strtoul(buf, NULL, 10);
static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm_reg, store_vrm_reg);
-static ssize_t show_alarms_reg(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_alarms_reg(struct device *dev, struct device_attribute
+ *attr, char *buf)
{
struct lm85_data *data = lm85_update_device(dev);
return sprintf(buf, "%u\n", data->alarms);
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", PWM_FROM_REG(data->pwm[nr]) );
+ return sprintf(buf, "%d\n", PWM_FROM_REG(data->pwm[nr]));
}
static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf( buf, "%d\n", INSEXT_FROM_REG(nr,
- data->in[nr],
- data->in_ext[nr]));
+ return sprintf(buf, "%d\n", INSEXT_FROM_REG(nr, data->in[nr],
+ data->in_ext[nr]));
}
-static ssize_t show_in_min(struct device *dev, struct device_attribute *attr,
+static ssize_t show_in_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_min[nr]) );
+ return sprintf(buf, "%d\n", INS_FROM_REG(nr, data->in_min[nr]));
}
static ssize_t set_in_min(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", INS_FROM_REG(nr, data->in_max[nr]) );
+ return sprintf(buf, "%d\n", INS_FROM_REG(nr, data->in_max[nr]));
}
static ssize_t set_in_max(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMPEXT_FROM_REG(data->temp[nr],
- data->temp_ext[nr]));
+ return sprintf(buf, "%d\n", TEMPEXT_FROM_REG(data->temp[nr],
+ data->temp_ext[nr]));
}
static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_min[nr]) );
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_min[nr]));
}
static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->temp_max[nr]) );
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp_max[nr]));
}
static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
int nr = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct lm85_data *data = i2c_get_clientdata(client);
- long val = simple_strtol(buf, NULL, 10);
+ long val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->temp_max[nr] = TEMP_TO_REG(val);
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", ZONE_FROM_REG(data->autofan[nr].config));
+ return sprintf(buf, "%d\n", ZONE_FROM_REG(data->autofan[nr].config));
}
static ssize_t set_pwm_auto_channels(struct device *dev,
int nr = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct lm85_data *data = i2c_get_clientdata(client);
- long val = simple_strtol(buf, NULL, 10);
+ long val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->autofan[nr].config = (data->autofan[nr].config & (~0xe0))
- | ZONE_TO_REG(val) ;
+ | ZONE_TO_REG(val);
lm85_write_value(client, LM85_REG_AFAN_CONFIG(nr),
data->autofan[nr].config);
mutex_unlock(&data->update_lock);
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", PWM_FROM_REG(data->autofan[nr].min_pwm));
+ return sprintf(buf, "%d\n", PWM_FROM_REG(data->autofan[nr].min_pwm));
}
static ssize_t set_pwm_auto_pwm_min(struct device *dev,
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", data->autofan[nr].min_off);
+ return sprintf(buf, "%d\n", data->autofan[nr].min_off);
}
static ssize_t set_pwm_auto_pwm_minctl(struct device *dev,
struct i2c_client *client = to_i2c_client(dev);
struct lm85_data *data = i2c_get_clientdata(client);
long val = simple_strtol(buf, NULL, 10);
+ u8 tmp;
mutex_lock(&data->update_lock);
data->autofan[nr].min_off = val;
- lm85_write_value(client, LM85_REG_AFAN_SPIKE1, data->smooth[0]
- | data->syncpwm3
- | (data->autofan[0].min_off ? 0x20 : 0)
- | (data->autofan[1].min_off ? 0x40 : 0)
- | (data->autofan[2].min_off ? 0x80 : 0)
- );
+ tmp = lm85_read_value(client, LM85_REG_AFAN_SPIKE1);
+ tmp &= ~(0x20 << nr);
+ if (data->autofan[nr].min_off)
+ tmp |= 0x20 << nr;
+ lm85_write_value(client, LM85_REG_AFAN_SPIKE1, tmp);
mutex_unlock(&data->update_lock);
return count;
}
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", FREQ_FROM_REG(data->autofan[nr].freq));
+ return sprintf(buf, "%d\n", FREQ_FROM_REG(data->autofan[nr].freq));
}
static ssize_t set_pwm_auto_pwm_freq(struct device *dev,
data->autofan[nr].freq = FREQ_TO_REG(val);
lm85_write_value(client, LM85_REG_AFAN_RANGE(nr),
(data->zone[nr].range << 4)
- | data->autofan[nr].freq
- );
+ | data->autofan[nr].freq);
mutex_unlock(&data->update_lock);
return count;
}
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) -
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->zone[nr].limit) -
HYST_FROM_REG(data->zone[nr].hyst));
}
min = TEMP_FROM_REG(data->zone[nr].limit);
data->zone[nr].off_desired = TEMP_TO_REG(val);
data->zone[nr].hyst = HYST_TO_REG(min - val);
- if ( nr == 0 || nr == 1 ) {
+ if (nr == 0 || nr == 1) {
lm85_write_value(client, LM85_REG_AFAN_HYST1,
(data->zone[0].hyst << 4)
- | data->zone[1].hyst
- );
+ | data->zone[1].hyst);
} else {
lm85_write_value(client, LM85_REG_AFAN_HYST2,
- (data->zone[2].hyst << 4)
- );
+ (data->zone[2].hyst << 4));
}
mutex_unlock(&data->update_lock);
return count;
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) );
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->zone[nr].limit));
}
static ssize_t set_temp_auto_temp_min(struct device *dev,
data->zone[nr].hyst = HYST_TO_REG(TEMP_FROM_REG(
data->zone[nr].limit) - TEMP_FROM_REG(
data->zone[nr].off_desired));
- if ( nr == 0 || nr == 1 ) {
+ if (nr == 0 || nr == 1) {
lm85_write_value(client, LM85_REG_AFAN_HYST1,
(data->zone[0].hyst << 4)
- | data->zone[1].hyst
- );
+ | data->zone[1].hyst);
} else {
lm85_write_value(client, LM85_REG_AFAN_HYST2,
- (data->zone[2].hyst << 4)
- );
+ (data->zone[2].hyst << 4));
}
mutex_unlock(&data->update_lock);
return count;
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].limit) +
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->zone[nr].limit) +
RANGE_FROM_REG(data->zone[nr].range));
}
{
int nr = to_sensor_dev_attr(attr)->index;
struct lm85_data *data = lm85_update_device(dev);
- return sprintf(buf,"%d\n", TEMP_FROM_REG(data->zone[nr].critical));
+ return sprintf(buf, "%d\n", TEMP_FROM_REG(data->zone[nr].critical));
}
static ssize_t set_temp_auto_temp_crit(struct device *dev,
- struct device_attribute *attr,const char *buf, size_t count)
+ struct device_attribute *attr, const char *buf, size_t count)
{
int nr = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = to_i2c_client(dev);
.attrs = lm85_attributes_in567,
};
+static void lm85_init_client(struct i2c_client *client)
+{
+ int value;
+
+ /* Start monitoring if needed */
+ value = lm85_read_value(client, LM85_REG_CONFIG);
+ if (!(value & 0x01)) {
+ dev_info(&client->dev, "Starting monitoring\n");
+ lm85_write_value(client, LM85_REG_CONFIG, value | 0x01);
+ }
+
+ /* Warn about unusual configuration bits */
+ if (value & 0x02)
+ dev_warn(&client->dev, "Device configuration is locked\n");
+ if (!(value & 0x04))
+ dev_warn(&client->dev, "Device is not ready\n");
+}
+
static int lm85_detect(struct i2c_adapter *adapter, int address,
int kind)
{
- int company, verstep ;
- struct i2c_client *new_client = NULL;
+ int company, verstep;
+ struct i2c_client *client;
struct lm85_data *data;
int err = 0;
- const char *type_name = "";
+ const char *type_name;
- if (!i2c_check_functionality(adapter,
- I2C_FUNC_SMBUS_BYTE_DATA)) {
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
/* We need to be able to do byte I/O */
- goto ERROR0 ;
- };
+ goto ERROR0;
+ }
/* OK. For now, we presume we have a valid client. We now create the
client structure, even though we cannot fill it completely yet.
goto ERROR0;
}
- new_client = &data->client;
- i2c_set_clientdata(new_client, data);
- new_client->addr = address;
- new_client->adapter = adapter;
- new_client->driver = &lm85_driver;
- new_client->flags = 0;
+ client = &data->client;
+ i2c_set_clientdata(client, data);
+ client->addr = address;
+ client->adapter = adapter;
+ client->driver = &lm85_driver;
/* Now, we do the remaining detection. */
- company = lm85_read_value(new_client, LM85_REG_COMPANY);
- verstep = lm85_read_value(new_client, LM85_REG_VERSTEP);
+ company = lm85_read_value(client, LM85_REG_COMPANY);
+ verstep = lm85_read_value(client, LM85_REG_VERSTEP);
dev_dbg(&adapter->dev, "Detecting device at %d,0x%02x with"
" COMPANY: 0x%02x and VERSTEP: 0x%02x\n",
- i2c_adapter_id(new_client->adapter), new_client->addr,
+ i2c_adapter_id(client->adapter), client->addr,
company, verstep);
/* If auto-detecting, Determine the chip type. */
if (kind <= 0) {
dev_dbg(&adapter->dev, "Autodetecting device at %d,0x%02x ...\n",
- i2c_adapter_id(adapter), address );
- if( company == LM85_COMPANY_NATIONAL
- && verstep == LM85_VERSTEP_LM85C ) {
- kind = lm85c ;
- } else if( company == LM85_COMPANY_NATIONAL
- && verstep == LM85_VERSTEP_LM85B ) {
- kind = lm85b ;
- } else if( company == LM85_COMPANY_NATIONAL
- && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC ) {
+ i2c_adapter_id(adapter), address);
+ if (company == LM85_COMPANY_NATIONAL
+ && verstep == LM85_VERSTEP_LM85C) {
+ kind = lm85c;
+ } else if (company == LM85_COMPANY_NATIONAL
+ && verstep == LM85_VERSTEP_LM85B) {
+ kind = lm85b;
+ } else if (company == LM85_COMPANY_NATIONAL
+ && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
dev_err(&adapter->dev, "Unrecognized version/stepping 0x%02x"
" Defaulting to LM85.\n", verstep);
- kind = any_chip ;
- } else if( company == LM85_COMPANY_ANALOG_DEV
- && verstep == LM85_VERSTEP_ADM1027 ) {
- kind = adm1027 ;
- } else if( company == LM85_COMPANY_ANALOG_DEV
+ kind = any_chip;
+ } else if (company == LM85_COMPANY_ANALOG_DEV
+ && verstep == LM85_VERSTEP_ADM1027) {
+ kind = adm1027;
+ } else if (company == LM85_COMPANY_ANALOG_DEV
&& (verstep == LM85_VERSTEP_ADT7463
- || verstep == LM85_VERSTEP_ADT7463C) ) {
- kind = adt7463 ;
- } else if( company == LM85_COMPANY_ANALOG_DEV
- && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC ) {
+ || verstep == LM85_VERSTEP_ADT7463C)) {
+ kind = adt7463;
+ } else if (company == LM85_COMPANY_ANALOG_DEV
+ && (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
dev_err(&adapter->dev, "Unrecognized version/stepping 0x%02x"
- " Defaulting to Generic LM85.\n", verstep );
- kind = any_chip ;
- } else if( company == LM85_COMPANY_SMSC
+ " Defaulting to Generic LM85.\n", verstep);
+ kind = any_chip;
+ } else if (company == LM85_COMPANY_SMSC
&& (verstep == LM85_VERSTEP_EMC6D100_A0
- || verstep == LM85_VERSTEP_EMC6D100_A1) ) {
+ || verstep == LM85_VERSTEP_EMC6D100_A1)) {
/* Unfortunately, we can't tell a '100 from a '101
* from the registers. Since a '101 is a '100
* in a package with fewer pins and therefore no
* 3.3V, 1.5V or 1.8V inputs, perhaps if those
* inputs read 0, then it's a '101.
*/
- kind = emc6d100 ;
- } else if( company == LM85_COMPANY_SMSC
+ kind = emc6d100;
+ } else if (company == LM85_COMPANY_SMSC
&& verstep == LM85_VERSTEP_EMC6D102) {
- kind = emc6d102 ;
- } else if( company == LM85_COMPANY_SMSC
+ kind = emc6d102;
+ } else if (company == LM85_COMPANY_SMSC
&& (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
dev_err(&adapter->dev, "lm85: Detected SMSC chip\n");
dev_err(&adapter->dev, "lm85: Unrecognized version/stepping 0x%02x"
- " Defaulting to Generic LM85.\n", verstep );
- kind = any_chip ;
- } else if( kind == any_chip
+ " Defaulting to Generic LM85.\n", verstep);
+ kind = any_chip;
+ } else if (kind == any_chip
&& (verstep & LM85_VERSTEP_VMASK) == LM85_VERSTEP_GENERIC) {
dev_err(&adapter->dev, "Generic LM85 Version 6 detected\n");
/* Leave kind as "any_chip" */
} else {
dev_dbg(&adapter->dev, "Autodetection failed\n");
- /* Not an LM85 ... */
- if( kind == any_chip ) { /* User used force=x,y */
+ /* Not an LM85... */
+ if (kind == any_chip) { /* User used force=x,y */
dev_err(&adapter->dev, "Generic LM85 Version 6 not"
" found at %d,0x%02x. Try force_lm85c.\n",
- i2c_adapter_id(adapter), address );
+ i2c_adapter_id(adapter), address);
}
- err = 0 ;
+ err = 0;
goto ERROR1;
}
}
/* Fill in the chip specific driver values */
- if ( kind == any_chip ) {
- type_name = "lm85";
- } else if ( kind == lm85b ) {
+ switch (kind) {
+ case lm85b:
type_name = "lm85b";
- } else if ( kind == lm85c ) {
+ break;
+ case lm85c:
type_name = "lm85c";
- } else if ( kind == adm1027 ) {
+ break;
+ case adm1027:
type_name = "adm1027";
- } else if ( kind == adt7463 ) {
+ break;
+ case adt7463:
type_name = "adt7463";
- } else if ( kind == emc6d100){
+ break;
+ case emc6d100:
type_name = "emc6d100";
- } else if ( kind == emc6d102 ) {
+ break;
+ case emc6d102:
type_name = "emc6d102";
+ break;
+ default:
+ type_name = "lm85";
}
- strlcpy(new_client->name, type_name, I2C_NAME_SIZE);
+ strlcpy(client->name, type_name, I2C_NAME_SIZE);
/* Fill in the remaining client fields */
data->type = kind;
- data->valid = 0;
mutex_init(&data->update_lock);
/* Tell the I2C layer a new client has arrived */
- if ((err = i2c_attach_client(new_client)))
+ err = i2c_attach_client(client);
+ if (err)
goto ERROR1;
/* Set the VRM version */
data->vrm = vid_which_vrm();
/* Initialize the LM85 chip */
- lm85_init_client(new_client);
+ lm85_init_client(client);
/* Register sysfs hooks */
- if ((err = sysfs_create_group(&new_client->dev.kobj, &lm85_group)))
+ err = sysfs_create_group(&client->dev.kobj, &lm85_group);
+ if (err)
goto ERROR2;
/* The ADT7463 has an optional VRM 10 mode where pin 21 is used
as a sixth digital VID input rather than an analog input. */
- data->vid = lm85_read_value(new_client, LM85_REG_VID);
+ data->vid = lm85_read_value(client, LM85_REG_VID);
if (!(kind == adt7463 && (data->vid & 0x80)))
- if ((err = sysfs_create_group(&new_client->dev.kobj,
+ if ((err = sysfs_create_group(&client->dev.kobj,
&lm85_group_in4)))
goto ERROR3;
/* The EMC6D100 has 3 additional voltage inputs */
if (kind == emc6d100)
- if ((err = sysfs_create_group(&new_client->dev.kobj,
+ if ((err = sysfs_create_group(&client->dev.kobj,
&lm85_group_in567)))
goto ERROR3;
- data->hwmon_dev = hwmon_device_register(&new_client->dev);
+ data->hwmon_dev = hwmon_device_register(&client->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto ERROR3;
return 0;
/* Error out and cleanup code */
- ERROR3:
- sysfs_remove_group(&new_client->dev.kobj, &lm85_group);
- sysfs_remove_group(&new_client->dev.kobj, &lm85_group_in4);
+ ERROR3:
+ sysfs_remove_group(&client->dev.kobj, &lm85_group);
+ sysfs_remove_group(&client->dev.kobj, &lm85_group_in4);
if (kind == emc6d100)
- sysfs_remove_group(&new_client->dev.kobj, &lm85_group_in567);
- ERROR2:
- i2c_detach_client(new_client);
- ERROR1:
+ sysfs_remove_group(&client->dev.kobj, &lm85_group_in567);
+ ERROR2:
+ i2c_detach_client(client);
+ ERROR1:
kfree(data);
- ERROR0:
+ ERROR0:
return err;
}
int res;
/* What size location is it? */
- switch( reg ) {
- case LM85_REG_FAN(0) : /* Read WORD data */
- case LM85_REG_FAN(1) :
- case LM85_REG_FAN(2) :
- case LM85_REG_FAN(3) :
- case LM85_REG_FAN_MIN(0) :
- case LM85_REG_FAN_MIN(1) :
- case LM85_REG_FAN_MIN(2) :
- case LM85_REG_FAN_MIN(3) :
- case LM85_REG_ALARM1 : /* Read both bytes at once */
- res = i2c_smbus_read_byte_data(client, reg) & 0xff ;
- res |= i2c_smbus_read_byte_data(client, reg+1) << 8 ;
- break ;
- case ADT7463_REG_TMIN_CTL1 : /* Read WORD MSB, LSB */
- res = i2c_smbus_read_byte_data(client, reg) << 8 ;
- res |= i2c_smbus_read_byte_data(client, reg+1) & 0xff ;
- break ;
+ switch (reg) {
+ case LM85_REG_FAN(0): /* Read WORD data */
+ case LM85_REG_FAN(1):
+ case LM85_REG_FAN(2):
+ case LM85_REG_FAN(3):
+ case LM85_REG_FAN_MIN(0):
+ case LM85_REG_FAN_MIN(1):
+ case LM85_REG_FAN_MIN(2):
+ case LM85_REG_FAN_MIN(3):
+ case LM85_REG_ALARM1: /* Read both bytes at once */
+ res = i2c_smbus_read_byte_data(client, reg) & 0xff;
+ res |= i2c_smbus_read_byte_data(client, reg + 1) << 8;
+ break;
default: /* Read BYTE data */
res = i2c_smbus_read_byte_data(client, reg);
- break ;
+ break;
}
- return res ;
+ return res;
}
-static int lm85_write_value(struct i2c_client *client, u8 reg, int value)
+static void lm85_write_value(struct i2c_client *client, u8 reg, int value)
{
- int res ;
-
- switch( reg ) {
- case LM85_REG_FAN(0) : /* Write WORD data */
- case LM85_REG_FAN(1) :
- case LM85_REG_FAN(2) :
- case LM85_REG_FAN(3) :
- case LM85_REG_FAN_MIN(0) :
- case LM85_REG_FAN_MIN(1) :
- case LM85_REG_FAN_MIN(2) :
- case LM85_REG_FAN_MIN(3) :
+ switch (reg) {
+ case LM85_REG_FAN(0): /* Write WORD data */
+ case LM85_REG_FAN(1):
+ case LM85_REG_FAN(2):
+ case LM85_REG_FAN(3):
+ case LM85_REG_FAN_MIN(0):
+ case LM85_REG_FAN_MIN(1):
+ case LM85_REG_FAN_MIN(2):
+ case LM85_REG_FAN_MIN(3):
/* NOTE: ALARM is read only, so not included here */
- res = i2c_smbus_write_byte_data(client, reg, value & 0xff) ;
- res |= i2c_smbus_write_byte_data(client, reg+1, (value>>8) & 0xff) ;
- break ;
- case ADT7463_REG_TMIN_CTL1 : /* Write WORD MSB, LSB */
- res = i2c_smbus_write_byte_data(client, reg, (value>>8) & 0xff);
- res |= i2c_smbus_write_byte_data(client, reg+1, value & 0xff) ;
- break ;
+ i2c_smbus_write_byte_data(client, reg, value & 0xff);
+ i2c_smbus_write_byte_data(client, reg + 1, value >> 8);
+ break;
default: /* Write BYTE data */
- res = i2c_smbus_write_byte_data(client, reg, value);
- break ;
+ i2c_smbus_write_byte_data(client, reg, value);
+ break;
}
-
- return res ;
-}
-
-static void lm85_init_client(struct i2c_client *client)
-{
- int value;
- struct lm85_data *data = i2c_get_clientdata(client);
-
- dev_dbg(&client->dev, "Initializing device\n");
-
- /* Warn if part was not "READY" */
- value = lm85_read_value(client, LM85_REG_CONFIG);
- dev_dbg(&client->dev, "LM85_REG_CONFIG is: 0x%02x\n", value);
- if( value & 0x02 ) {
- dev_err(&client->dev, "Client (%d,0x%02x) config is locked.\n",
- i2c_adapter_id(client->adapter), client->addr );
- };
- if( ! (value & 0x04) ) {
- dev_err(&client->dev, "Client (%d,0x%02x) is not ready.\n",
- i2c_adapter_id(client->adapter), client->addr );
- };
- if( value & 0x10
- && ( data->type == adm1027
- || data->type == adt7463 ) ) {
- dev_err(&client->dev, "Client (%d,0x%02x) VxI mode is set. "
- "Please report this to the lm85 maintainer.\n",
- i2c_adapter_id(client->adapter), client->addr );
- };
-
- /* WE INTENTIONALLY make no changes to the limits,
- * offsets, pwms, fans and zones. If they were
- * configured, we don't want to mess with them.
- * If they weren't, the default is 100% PWM, no
- * control and will suffice until 'sensors -s'
- * can be run by the user.
- */
-
- /* Start monitoring */
- value = lm85_read_value(client, LM85_REG_CONFIG);
- /* Try to clear LOCK, Set START, save everything else */
- value = (value & ~ 0x02) | 0x01 ;
- dev_dbg(&client->dev, "Setting CONFIG to: 0x%02x\n", value);
- lm85_write_value(client, LM85_REG_CONFIG, value);
}
static struct lm85_data *lm85_update_device(struct device *dev)
mutex_lock(&data->update_lock);
- if ( !data->valid ||
- time_after(jiffies, data->last_reading + LM85_DATA_INTERVAL) ) {
+ if (!data->valid ||
+ time_after(jiffies, data->last_reading + LM85_DATA_INTERVAL)) {
/* Things that change quickly */
dev_dbg(&client->dev, "Reading sensor values\n");
-
+
/* Have to read extended bits first to "freeze" the
* more significant bits that are read later.
* There are 2 additional resolution bits per channel and we
* have room for 4, so we shift them to the left.
*/
- if ( (data->type == adm1027) || (data->type == adt7463) ) {
+ if (data->type == adm1027 || data->type == adt7463) {
int ext1 = lm85_read_value(client,
ADM1027_REG_EXTEND_ADC1);
int ext2 = lm85_read_value(client,
ADM1027_REG_EXTEND_ADC2);
int val = (ext1 << 8) + ext2;
- for(i = 0; i <= 4; i++)
- data->in_ext[i] = ((val>>(i * 2))&0x03) << 2;
+ for (i = 0; i <= 4; i++)
+ data->in_ext[i] =
+ ((val >> (i * 2)) & 0x03) << 2;
- for(i = 0; i <= 2; i++)
- data->temp_ext[i] = (val>>((i + 4) * 2))&0x0c;
+ for (i = 0; i <= 2; i++)
+ data->temp_ext[i] =
+ (val >> ((i + 4) * 2)) & 0x0c;
}
data->vid = lm85_read_value(client, LM85_REG_VID);
for (i = 0; i <= 3; ++i) {
data->in[i] =
lm85_read_value(client, LM85_REG_IN(i));
+ data->fan[i] =
+ lm85_read_value(client, LM85_REG_FAN(i));
}
if (!(data->type == adt7463 && (data->vid & 0x80))) {
LM85_REG_IN(4));
}
- for (i = 0; i <= 3; ++i) {
- data->fan[i] =
- lm85_read_value(client, LM85_REG_FAN(i));
- }
-
for (i = 0; i <= 2; ++i) {
data->temp[i] =
lm85_read_value(client, LM85_REG_TEMP(i));
- }
-
- for (i = 0; i <= 2; ++i) {
data->pwm[i] =
lm85_read_value(client, LM85_REG_PWM(i));
}
data->alarms = lm85_read_value(client, LM85_REG_ALARM1);
- if ( data->type == adt7463 ) {
- if( data->therm_total < ULONG_MAX - 256 ) {
- data->therm_total +=
- lm85_read_value(client, ADT7463_REG_THERM );
- }
- } else if ( data->type == emc6d100 ) {
+ if (data->type == emc6d100) {
/* Three more voltage sensors */
for (i = 5; i <= 7; ++i) {
- data->in[i] =
- lm85_read_value(client, EMC6D100_REG_IN(i));
+ data->in[i] = lm85_read_value(client,
+ EMC6D100_REG_IN(i));
}
/* More alarm bits */
- data->alarms |=
- lm85_read_value(client, EMC6D100_REG_ALARM3) << 16;
- } else if (data->type == emc6d102 ) {
+ data->alarms |= lm85_read_value(client,
+ EMC6D100_REG_ALARM3) << 16;
+ } else if (data->type == emc6d102) {
/* Have to read LSB bits after the MSB ones because
the reading of the MSB bits has frozen the
LSBs (backward from the ADM1027).
EMC6D102_REG_EXTEND_ADC4);
data->in_ext[0] = ext3 & 0x0f;
data->in_ext[1] = ext4 & 0x0f;
- data->in_ext[2] = (ext4 >> 4) & 0x0f;
- data->in_ext[3] = (ext3 >> 4) & 0x0f;
- data->in_ext[4] = (ext2 >> 4) & 0x0f;
+ data->in_ext[2] = ext4 >> 4;
+ data->in_ext[3] = ext3 >> 4;
+ data->in_ext[4] = ext2 >> 4;
data->temp_ext[0] = ext1 & 0x0f;
data->temp_ext[1] = ext2 & 0x0f;
- data->temp_ext[2] = (ext1 >> 4) & 0x0f;
+ data->temp_ext[2] = ext1 >> 4;
}
- data->last_reading = jiffies ;
- }; /* last_reading */
+ data->last_reading = jiffies;
+ } /* last_reading */
- if ( !data->valid ||
- time_after(jiffies, data->last_config + LM85_CONFIG_INTERVAL) ) {
+ if (!data->valid ||
+ time_after(jiffies, data->last_config + LM85_CONFIG_INTERVAL)) {
/* Things that don't change often */
dev_dbg(&client->dev, "Reading config values\n");
lm85_read_value(client, LM85_REG_IN_MIN(i));
data->in_max[i] =
lm85_read_value(client, LM85_REG_IN_MAX(i));
+ data->fan_min[i] =
+ lm85_read_value(client, LM85_REG_FAN_MIN(i));
}
if (!(data->type == adt7463 && (data->vid & 0x80))) {
LM85_REG_IN_MAX(4));
}
- if ( data->type == emc6d100 ) {
+ if (data->type == emc6d100) {
for (i = 5; i <= 7; ++i) {
- data->in_min[i] =
- lm85_read_value(client, EMC6D100_REG_IN_MIN(i));
- data->in_max[i] =
- lm85_read_value(client, EMC6D100_REG_IN_MAX(i));
+ data->in_min[i] = lm85_read_value(client,
+ EMC6D100_REG_IN_MIN(i));
+ data->in_max[i] = lm85_read_value(client,
+ EMC6D100_REG_IN_MAX(i));
}
}
- for (i = 0; i <= 3; ++i) {
- data->fan_min[i] =
- lm85_read_value(client, LM85_REG_FAN_MIN(i));
- }
-
for (i = 0; i <= 2; ++i) {
+ int val;
+
data->temp_min[i] =
lm85_read_value(client, LM85_REG_TEMP_MIN(i));
data->temp_max[i] =
lm85_read_value(client, LM85_REG_TEMP_MAX(i));
- }
- for (i = 0; i <= 2; ++i) {
- int val ;
data->autofan[i].config =
lm85_read_value(client, LM85_REG_AFAN_CONFIG(i));
val = lm85_read_value(client, LM85_REG_AFAN_RANGE(i));
- data->autofan[i].freq = val & 0x07 ;
- data->zone[i].range = (val >> 4) & 0x0f ;
+ data->autofan[i].freq = val & 0x07;
+ data->zone[i].range = val >> 4;
data->autofan[i].min_pwm =
lm85_read_value(client, LM85_REG_AFAN_MINPWM(i));
data->zone[i].limit =
}
i = lm85_read_value(client, LM85_REG_AFAN_SPIKE1);
- data->smooth[0] = i & 0x0f ;
- data->syncpwm3 = i & 0x10 ; /* Save PWM3 config */
- data->autofan[0].min_off = (i & 0x20) != 0 ;
- data->autofan[1].min_off = (i & 0x40) != 0 ;
- data->autofan[2].min_off = (i & 0x80) != 0 ;
- i = lm85_read_value(client, LM85_REG_AFAN_SPIKE2);
- data->smooth[1] = (i>>4) & 0x0f ;
- data->smooth[2] = i & 0x0f ;
+ data->autofan[0].min_off = (i & 0x20) != 0;
+ data->autofan[1].min_off = (i & 0x40) != 0;
+ data->autofan[2].min_off = (i & 0x80) != 0;
i = lm85_read_value(client, LM85_REG_AFAN_HYST1);
- data->zone[0].hyst = (i>>4) & 0x0f ;
- data->zone[1].hyst = i & 0x0f ;
+ data->zone[0].hyst = i >> 4;
+ data->zone[1].hyst = i & 0x0f;
i = lm85_read_value(client, LM85_REG_AFAN_HYST2);
- data->zone[2].hyst = (i>>4) & 0x0f ;
-
- if ( (data->type == lm85b) || (data->type == lm85c) ) {
- data->tach_mode = lm85_read_value(client,
- LM85_REG_TACH_MODE );
- data->spinup_ctl = lm85_read_value(client,
- LM85_REG_SPINUP_CTL );
- } else if ( (data->type == adt7463) || (data->type == adm1027) ) {
- if ( data->type == adt7463 ) {
- for (i = 0; i <= 2; ++i) {
- data->oppoint[i] = lm85_read_value(client,
- ADT7463_REG_OPPOINT(i) );
- }
- data->tmin_ctl = lm85_read_value(client,
- ADT7463_REG_TMIN_CTL1 );
- data->therm_limit = lm85_read_value(client,
- ADT7463_REG_THERM_LIMIT );
- }
- for (i = 0; i <= 2; ++i) {
- data->temp_offset[i] = lm85_read_value(client,
- ADM1027_REG_TEMP_OFFSET(i) );
- }
- data->tach_mode = lm85_read_value(client,
- ADM1027_REG_CONFIG3 );
- data->fan_ppr = lm85_read_value(client,
- ADM1027_REG_FAN_PPR );
- }
-
+ data->zone[2].hyst = i >> 4;
+
data->last_config = jiffies;
- }; /* last_config */
+ } /* last_config */
data->valid = 1;
return i2c_add_driver(&lm85_driver);
}
-static void __exit sm_lm85_exit(void)
+static void __exit sm_lm85_exit(void)
{
i2c_del_driver(&lm85_driver);
}
-/* Thanks to Richard Barrington for adding the LM85 to sensors-detect.
- * Thanks to Margit Schubert-While <margitsw@t-online.de> for help with
- * post 2.7.0 CVS changes.
- */
MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Philip Pokorny <ppokorny@penguincomputing.com>, Margit Schubert-While <margitsw@t-online.de>, Justin Thiessen <jthiessen@penguincomputing.com");
+MODULE_AUTHOR("Philip Pokorny <ppokorny@penguincomputing.com>, "
+ "Margit Schubert-While <margitsw@t-online.de>, "
+ "Justin Thiessen <jthiessen@penguincomputing.com>");
MODULE_DESCRIPTION("LM85-B, LM85-C driver");
module_init(sm_lm85_init);
static const u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
static const u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
static const u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
+static const u8 THMC50_REG_TEMP_CRITICAL[] = { 0x13, 0x14, 0x14 };
+static const u8 THMC50_REG_TEMP_DEFAULT[] = { 0x17, 0x18, 0x18 };
#define THMC50_REG_CONF_nFANOFF 0x20
+#define THMC50_REG_CONF_PROGRAMMED 0x08
/* Each client has this additional data */
struct thmc50_data {
s8 temp_input[3];
s8 temp_max[3];
s8 temp_min[3];
+ s8 temp_critical[3];
u8 analog_out;
u8 alarms;
};
return count;
}
+static ssize_t show_temp_critical(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ int nr = to_sensor_dev_attr(attr)->index;
+ struct thmc50_data *data = thmc50_update_device(dev);
+ return sprintf(buf, "%d\n", data->temp_critical[nr] * 1000);
+}
+
static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
char *buf)
{
static SENSOR_DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR, \
show_temp_min, set_temp_min, offset - 1); \
static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR, \
- show_temp_max, set_temp_max, offset - 1);
+ show_temp_max, set_temp_max, offset - 1); \
+static SENSOR_DEVICE_ATTR(temp##offset##_crit, S_IRUGO, \
+ show_temp_critical, NULL, offset - 1);
temp_reg(1);
temp_reg(2);
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_min.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp1_crit.dev_attr.attr,
&sensor_dev_attr_temp1_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_max.dev_attr.attr,
&sensor_dev_attr_temp2_min.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_crit.dev_attr.attr,
&sensor_dev_attr_temp2_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_fault.dev_attr.attr,
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_temp3_max.dev_attr.attr,
&sensor_dev_attr_temp3_min.dev_attr.attr,
&sensor_dev_attr_temp3_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_crit.dev_attr.attr,
&sensor_dev_attr_temp3_alarm.dev_attr.attr,
&sensor_dev_attr_temp3_fault.dev_attr.attr,
NULL
int temps = data->has_temp3 ? 3 : 2;
int i;
+ int prog = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
+
+ prog &= THMC50_REG_CONF_PROGRAMMED;
+
for (i = 0; i < temps; i++) {
data->temp_input[i] = i2c_smbus_read_byte_data(client,
THMC50_REG_TEMP[i]);
THMC50_REG_TEMP_MAX[i]);
data->temp_min[i] = i2c_smbus_read_byte_data(client,
THMC50_REG_TEMP_MIN[i]);
+ data->temp_critical[i] =
+ i2c_smbus_read_byte_data(client,
+ prog ? THMC50_REG_TEMP_CRITICAL[i]
+ : THMC50_REG_TEMP_DEFAULT[i]);
}
data->analog_out =
i2c_smbus_read_byte_data(client, THMC50_REG_ANALOG_OUT);
MODULE_PARM_DESC(force_i2c,
"Initialize the i2c address of the sensors");
-static int reset;
-module_param(reset, bool, 0);
-MODULE_PARM_DESC(reset, "Set to one to reset chip on load");
-
static int init = 1;
module_param(init, bool, 0);
MODULE_PARM_DESC(init, "Set to zero to bypass chip initialization");
#define W83627HF_REG_PWM1 0x5A
#define W83627HF_REG_PWM2 0x5B
+static const u8 W83627THF_REG_PWM_ENABLE[] = {
+ 0x04, /* FAN 1 mode */
+ 0x04, /* FAN 2 mode */
+ 0x12, /* FAN AUX mode */
+};
+static const u8 W83627THF_PWM_ENABLE_SHIFT[] = { 2, 4, 1 };
+
#define W83627THF_REG_PWM1 0x01 /* 697HF/637HF/687THF too */
#define W83627THF_REG_PWM2 0x03 /* 697HF/637HF/687THF too */
#define W83627THF_REG_PWM3 0x11 /* 637HF/687THF too */
u32 alarms; /* Register encoding, combined */
u32 beep_mask; /* Register encoding, combined */
u8 pwm[3]; /* Register value */
+ u8 pwm_enable[3]; /* 1 = manual
+ 2 = thermal cruise (also called SmartFan I)
+ 3 = fan speed cruise */
u8 pwm_freq[3]; /* Register value */
u16 sens[3]; /* 1 = pentium diode; 2 = 3904 diode;
4 = thermistor */
static SENSOR_DEVICE_ATTR(pwm2, S_IRUGO|S_IWUSR, show_pwm, store_pwm, 1);
static SENSOR_DEVICE_ATTR(pwm3, S_IRUGO|S_IWUSR, show_pwm, store_pwm, 2);
+static ssize_t
+show_pwm_enable(struct device *dev, struct device_attribute *devattr, char *buf)
+{
+ int nr = to_sensor_dev_attr(devattr)->index;
+ struct w83627hf_data *data = w83627hf_update_device(dev);
+ return sprintf(buf, "%d\n", data->pwm_enable[nr]);
+}
+
+static ssize_t
+store_pwm_enable(struct device *dev, struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ int nr = to_sensor_dev_attr(devattr)->index;
+ struct w83627hf_data *data = dev_get_drvdata(dev);
+ unsigned long val = simple_strtoul(buf, NULL, 10);
+ u8 reg;
+
+ if (!val || (val > 3)) /* modes 1, 2 and 3 are supported */
+ return -EINVAL;
+ mutex_lock(&data->update_lock);
+ data->pwm_enable[nr] = val;
+ reg = w83627hf_read_value(data, W83627THF_REG_PWM_ENABLE[nr]);
+ reg &= ~(0x03 << W83627THF_PWM_ENABLE_SHIFT[nr]);
+ reg |= (val - 1) << W83627THF_PWM_ENABLE_SHIFT[nr];
+ w83627hf_write_value(data, W83627THF_REG_PWM_ENABLE[nr], reg);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static SENSOR_DEVICE_ATTR(pwm1_enable, S_IRUGO|S_IWUSR, show_pwm_enable,
+ store_pwm_enable, 0);
+static SENSOR_DEVICE_ATTR(pwm2_enable, S_IRUGO|S_IWUSR, show_pwm_enable,
+ store_pwm_enable, 1);
+static SENSOR_DEVICE_ATTR(pwm3_enable, S_IRUGO|S_IWUSR, show_pwm_enable,
+ store_pwm_enable, 2);
+
static ssize_t
show_pwm_freq(struct device *dev, struct device_attribute *devattr, char *buf)
{
&sensor_dev_attr_pwm1_freq.dev_attr.attr,
&sensor_dev_attr_pwm2_freq.dev_attr.attr,
&sensor_dev_attr_pwm3_freq.dev_attr.attr,
+
+ &sensor_dev_attr_pwm1_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm2_enable.dev_attr.attr,
+ &sensor_dev_attr_pwm3_enable.dev_attr.attr,
+
NULL
};
&sensor_dev_attr_pwm3_freq.dev_attr)))
goto ERROR4;
+ if (data->type != w83627hf)
+ if ((err = device_create_file(dev,
+ &sensor_dev_attr_pwm1_enable.dev_attr))
+ || (err = device_create_file(dev,
+ &sensor_dev_attr_pwm2_enable.dev_attr)))
+ goto ERROR4;
+
+ if (data->type == w83627thf || data->type == w83637hf
+ || data->type == w83687thf)
+ if ((err = device_create_file(dev,
+ &sensor_dev_attr_pwm3_enable.dev_attr)))
+ goto ERROR4;
+
data->hwmon_dev = hwmon_device_register(dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
enum chips type = data->type;
u8 tmp;
- if (reset) {
- /* Resetting the chip has been the default for a long time,
- but repeatedly caused problems (fans going to full
- speed...) so it is now optional. It might even go away if
- nobody reports it as being useful, as I see very little
- reason why this would be needed at all. */
- dev_info(&pdev->dev, "If reset=1 solved a problem you were "
- "having, please report!\n");
-
- /* save this register */
- i = w83627hf_read_value(data, W83781D_REG_BEEP_CONFIG);
- /* Reset all except Watchdog values and last conversion values
- This sets fan-divs to 2, among others */
- w83627hf_write_value(data, W83781D_REG_CONFIG, 0x80);
- /* Restore the register and disable power-on abnormal beep.
- This saves FAN 1/2/3 input/output values set by BIOS. */
- w83627hf_write_value(data, W83781D_REG_BEEP_CONFIG, i | 0x80);
- /* Disable master beep-enable (reset turns it on).
- Individual beeps should be reset to off but for some reason
- disabling this bit helps some people not get beeped */
- w83627hf_write_value(data, W83781D_REG_BEEP_INTS2, 0);
- }
-
/* Minimize conflicts with other winbond i2c-only clients... */
/* disable i2c subclients... how to disable main i2c client?? */
/* force i2c address to relatively uncommon address */
{
struct w83627hf_data *data = dev_get_drvdata(dev);
int i, num_temps = (data->type == w83697hf) ? 2 : 3;
+ int num_pwms = (data->type == w83697hf) ? 2 : 3;
mutex_lock(&data->update_lock);
break;
}
}
+ if (data->type != w83627hf) {
+ for (i = 0; i < num_pwms; i++) {
+ u8 tmp = w83627hf_read_value(data,
+ W83627THF_REG_PWM_ENABLE[i]);
+ data->pwm_enable[i] =
+ ((tmp >> W83627THF_PWM_ENABLE_SHIFT[i])
+ & 0x03) + 1;
+ }
+ }
for (i = 0; i < num_temps; i++) {
data->temp[i] = w83627hf_read_value(
data, w83627hf_reg_temp[i]);
static u8 div_to_reg(int nr, long val)
{
int i;
- int max;
- /* first three fan's divisor max out at 8, rest max out at 128 */
- max = (nr < 3) ? 8 : 128;
- val = SENSORS_LIMIT(val, 1, max) >> 1;
+ /* fan divisors max out at 128 */
+ val = SENSORS_LIMIT(val, 1, 128) >> 1;
for (i = 0; i < 7; i++) {
if (val == 0)
break;
unsigned long min;
u8 tmp_fan_div;
u8 fan_div_reg;
+ u8 vbat_reg;
int indx = 0;
u8 keep_mask = 0;
u8 new_shift = 0;
w83791d_write(client, W83791D_REG_FAN_DIV[indx],
fan_div_reg | tmp_fan_div);
+ /* Bit 2 of fans 0-2 is stored in the vbat register (bits 5-7) */
+ if (nr < 3) {
+ keep_mask = ~(1 << (nr + 5));
+ vbat_reg = w83791d_read(client, W83791D_REG_VBAT)
+ & keep_mask;
+ tmp_fan_div = (data->fan_div[nr] << (3 + nr)) & ~keep_mask;
+ w83791d_write(client, W83791D_REG_VBAT,
+ vbat_reg | tmp_fan_div);
+ }
+
/* Restore fan_min */
data->fan_min[nr] = fan_to_reg(min, DIV_FROM_REG(data->fan_div[nr]));
w83791d_write(client, W83791D_REG_FAN_MIN[nr], data->fan_min[nr]);
struct w83791d_data *data = i2c_get_clientdata(client);
int i, j;
u8 reg_array_tmp[3];
+ u8 vbat_reg;
mutex_lock(&data->update_lock);
data->fan_div[3] = reg_array_tmp[2] & 0x07;
data->fan_div[4] = (reg_array_tmp[2] >> 4) & 0x07;
+ /* The fan divisor for fans 0-2 get bit 2 from
+ bits 5-7 respectively of vbat register */
+ vbat_reg = w83791d_read(client, W83791D_REG_VBAT);
+ for (i = 0; i < 3; i++)
+ data->fan_div[i] |= (vbat_reg >> (3 + i)) & 0x04;
+
/* Update the first temperature sensor */
for (i = 0; i < 3; i++) {
data->temp1[i] = w83791d_read(client,
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/hardware/ioc.h>
#include <asm/system.h>
#include <asm/io.h>
-#include <asm/arch/at91_twi.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
+#include <mach/at91_twi.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
#define TWI_CLOCK 100000 /* Hz. max 400 Kbits/sec */
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
+#include <mach/hardware.h>
-#include <asm/arch/i2c.h>
+#include <mach/i2c.h>
/* ----- global defines ----------------------------------------------- */
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
-#include <asm/hardware.h> /* Pick up IXP2000-specific bits */
-#include <asm/arch/gpio.h>
+#include <mach/hardware.h> /* Pick up IXP2000-specific bits */
+#include <mach/gpio.h>
static inline int ixp2000_scl_pin(void *data)
{
#include <linux/completion.h>
#include <linux/platform_device.h>
#include <linux/i2c-pnx.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <linux/err.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/i2c.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/i2c.h>
+#include <mach/pxa-regs.h>
struct pxa_i2c {
spinlock_t lock;
#include <linux/clk.h>
#include <linux/cpufreq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c/regs-iic.h>
#include <asm/plat-s3c/iic.h>
#include <linux/workqueue.h>
#include <asm/irq.h>
-#include <asm/arch/usb.h>
+#include <mach/usb.h>
#ifndef DEBUG
/* board-specific PM hooks */
#include <asm/gpio.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
#include <asm/mach-types.h>
#include <linux/rtc.h>
#include <linux/bcd.h>
-#include <asm/mach-types.h>
#include <asm/mach/irq.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/menelaus.h>
+#include <mach/gpio.h>
+#include <mach/menelaus.h>
#define DRIVER_NAME "menelaus"
if IDE
-config IDE_MAX_HWIFS
- int "Max IDE interfaces"
- depends on ALPHA || SUPERH || IA64 || EMBEDDED
- range 1 10
- default 4
- help
- This is the maximum number of IDE hardware interfaces that will
- be supported by the driver. Make sure it is at least as high as
- the number of IDE interfaces in your system.
-
config BLK_DEV_IDE
tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
---help---
#include <linux/init.h>
#include <linux/ide.h>
-#include <asm/mach-types.h>
#include <asm/irq.h>
#define DRV_NAME "ide_arm"
#ifdef CONFIG_ARCH_CLPS7500
-# include <asm/arch/hardware.h>
+# include <mach/hardware.h>
#
# define IDE_ARM_IO (ISASLOT_IO + 0x1f0)
# define IDE_ARM_IRQ IRQ_ISA_14
palm_bk3710_setpiomode(base, NULL, 1, 600, 0);
}
-static u8 __devinit palm_bk3710_cable_detect(ide_hwif_t *hwif)
+static u8 palm_bk3710_cable_detect(ide_hwif_t *hwif)
{
return ATA_CBL_PATA80;
}
mutex_lock(&idecd_ref_mutex);
cd = ide_cd_g(disk);
if (cd) {
- kref_get(&cd->kref);
- if (ide_device_get(cd->drive)) {
- kref_put(&cd->kref, ide_cd_release);
+ if (ide_device_get(cd->drive))
cd = NULL;
- }
+ else
+ kref_get(&cd->kref);
+
}
mutex_unlock(&idecd_ref_mutex);
return cd;
static void ide_cd_put(struct cdrom_info *cd)
{
+ ide_drive_t *drive = cd->drive;
+
mutex_lock(&idecd_ref_mutex);
- ide_device_put(cd->drive);
kref_put(&cd->kref, ide_cd_release);
+ ide_device_put(drive);
mutex_unlock(&idecd_ref_mutex);
}
int stat;
unsigned char cmd[BLK_MAX_CDB];
unsigned len = sizeof(capbuf);
+ u32 blocklen;
memset(cmd, 0, BLK_MAX_CDB);
cmd[0] = GPCMD_READ_CDVD_CAPACITY;
/*
* Sanity check the given block size
*/
- switch (capbuf.blocklen) {
- case __constant_cpu_to_be32(512):
- case __constant_cpu_to_be32(1024):
- case __constant_cpu_to_be32(2048):
- case __constant_cpu_to_be32(4096):
+ blocklen = be32_to_cpu(capbuf.blocklen);
+ switch (blocklen) {
+ case 512:
+ case 1024:
+ case 2048:
+ case 4096:
break;
default:
printk(KERN_ERR "%s: weird block size %u\n",
- drive->name, capbuf.blocklen);
+ drive->name, blocklen);
printk(KERN_ERR "%s: default to 2kb block size\n",
drive->name);
- capbuf.blocklen = __constant_cpu_to_be32(2048);
+ blocklen = 2048;
break;
}
*capacity = 1 + be32_to_cpu(capbuf.lba);
- *sectors_per_frame = be32_to_cpu(capbuf.blocklen) >> SECTOR_BITS;
+ *sectors_per_frame = blocklen >> SECTOR_BITS;
return 0;
}
mutex_lock(&idedisk_ref_mutex);
idkp = ide_disk_g(disk);
if (idkp) {
- kref_get(&idkp->kref);
- if (ide_device_get(idkp->drive)) {
- kref_put(&idkp->kref, ide_disk_release);
+ if (ide_device_get(idkp->drive))
idkp = NULL;
- }
+ else
+ kref_get(&idkp->kref);
}
mutex_unlock(&idedisk_ref_mutex);
return idkp;
static void ide_disk_put(struct ide_disk_obj *idkp)
{
+ ide_drive_t *drive = idkp->drive;
+
mutex_lock(&idedisk_ref_mutex);
- ide_device_put(idkp->drive);
kref_put(&idkp->kref, ide_disk_release);
+ ide_device_put(drive);
mutex_unlock(&idedisk_ref_mutex);
}
if (id->field_valid & 2) {
mask = id->dma_1word & hwif->swdma_mask;
} else if (id->tDMA) {
- /*
- * ide_fix_driveid() doesn't convert ->tDMA to the
- * CPU endianness so we need to do it here
- */
- u8 mode = le16_to_cpu(id->tDMA);
+ u8 mode = id->tDMA;
/*
* if the mode is valid convert it to the mask
mutex_lock(&idefloppy_ref_mutex);
floppy = ide_floppy_g(disk);
if (floppy) {
- kref_get(&floppy->kref);
- if (ide_device_get(floppy->drive)) {
- kref_put(&floppy->kref, idefloppy_cleanup_obj);
+ if (ide_device_get(floppy->drive))
floppy = NULL;
- }
+ else
+ kref_get(&floppy->kref);
}
mutex_unlock(&idefloppy_ref_mutex);
return floppy;
static void ide_floppy_put(struct ide_floppy_obj *floppy)
{
+ ide_drive_t *drive = floppy->drive;
+
mutex_lock(&idefloppy_ref_mutex);
- ide_device_put(floppy->drive);
kref_put(&floppy->kref, idefloppy_cleanup_obj);
+ ide_device_put(drive);
mutex_unlock(&idefloppy_ref_mutex);
}
for (i = 0; i < 3; i++)
id->words157_159[i] = __le16_to_cpu(id->words157_159[i]);
id->cfa_power = __le16_to_cpu(id->cfa_power);
- for (i = 0; i < 14; i++)
+ for (i = 0; i < 15; i++)
id->words161_175[i] = __le16_to_cpu(id->words161_175[i]);
- for (i = 0; i < 31; i++)
+ for (i = 0; i < 30; i++)
id->words176_205[i] = __le16_to_cpu(id->words176_205[i]);
- for (i = 0; i < 48; i++)
+ for (i = 0; i < 49; i++)
id->words206_254[i] = __le16_to_cpu(id->words206_254[i]);
id->integrity_word = __le16_to_cpu(id->integrity_word);
# else
mutex_lock(&idetape_ref_mutex);
tape = ide_tape_g(disk);
if (tape) {
- kref_get(&tape->kref);
- if (ide_device_get(tape->drive)) {
- kref_put(&tape->kref, ide_tape_release);
+ if (ide_device_get(tape->drive))
tape = NULL;
- }
+ else
+ kref_get(&tape->kref);
}
mutex_unlock(&idetape_ref_mutex);
return tape;
static void ide_tape_put(struct ide_tape_obj *tape)
{
+ ide_drive_t *drive = tape->drive;
+
mutex_lock(&idetape_ref_mutex);
- ide_device_put(tape->drive);
kref_put(&tape->kref, ide_tape_release);
+ ide_device_put(drive);
mutex_unlock(&idetape_ref_mutex);
}
return dev->irq;
}
-static u8 __devinit atp86x_cable_detect(ide_hwif_t *hwif)
+static u8 atp86x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 ata66 = 0, mask = hwif->channel ? 0x02 : 0x01;
* FIXME: frobs bits that are not defined on newer ALi devicea
*/
-static u8 __devinit ali_cable_detect(ide_hwif_t *hwif)
+static u8 ali_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long flags;
return dev->irq;
}
-static u8 __devinit amd_cable_detect(ide_hwif_t *hwif)
+static u8 amd_cable_detect(ide_hwif_t *hwif)
{
if ((amd_80w >> hwif->channel) & 1)
return ATA_CBL_PATA80;
spin_unlock_irqrestore(&atiixp_lock, flags);
}
-static u8 __devinit atiixp_cable_detect(ide_hwif_t *hwif)
+static u8 atiixp_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
u8 udma_mode = 0, ch = hwif->channel;
return 0;
}
-static u8 __devinit cmd64x_cable_detect(ide_hwif_t *hwif)
+static u8 cmd64x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
static const struct ide_port_info cyrix_chipset __devinitdata = {
.name = DRV_NAME,
+ .enablebits = { { 0x60, 0x01, 0x01 }, { 0x60, 0x02, 0x02 } },
.port_ops = &cs5520_port_ops,
.host_flags = IDE_HFLAG_ISA_PORTS | IDE_HFLAG_CS5520,
.pio_mask = ATA_PIO4,
cs5535_set_speed(drive, XFER_PIO_0 + pio);
}
-static u8 __devinit cs5535_cable_detect(ide_hwif_t *hwif)
+static u8 cs5535_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 bit;
return dev->irq;
}
-static u8 __devinit hpt3xx_cable_detect(ide_hwif_t *hwif)
+static u8 hpt3xx_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
struct ide_host *host = pci_get_drvdata(dev);
}
}
-static u8 __devinit it8213_cable_detect(ide_hwif_t *hwif)
+static u8 it8213_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 reg42h = 0;
* the needed logic onboard.
*/
-static u8 __devinit it821x_cable_detect(ide_hwif_t *hwif)
+static u8 it821x_cable_detect(ide_hwif_t *hwif)
{
/* The reference driver also only does disk side */
return ATA_CBL_PATA80;
* final tuning that is needed, or fixups to work around bugs.
*/
-static void __devinit it821x_quirkproc(ide_drive_t *drive)
+static void it821x_quirkproc(ide_drive_t *drive)
{
struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif);
struct hd_driveid *id = drive->id;
* Returns the cable type.
*/
-static u8 __devinit jmicron_cable_detect(ide_hwif_t *hwif)
+static u8 jmicron_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
}
}
-static u8 __devinit pdcnew_cable_detect(ide_hwif_t *hwif)
+static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
{
if (get_indexed_reg(hwif, 0x0b) & 0x04)
return ATA_CBL_PATA40;
pdc202xx_set_mode(drive, XFER_PIO_0 + pio);
}
-static u8 __devinit pdc2026x_cable_detect(ide_hwif_t *hwif)
+static u8 pdc2026x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u16 CIS, mask = hwif->channel ? (1 << 11) : (1 << 10);
{ 0, }
};
-static u8 __devinit piix_cable_detect(ide_hwif_t *hwif)
+static u8 piix_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
const struct ich_laptop *lap = &ich_laptop[0];
init_mmio_iops_scc(hwif);
}
-static u8 __devinit scc_cable_detect(ide_hwif_t *hwif)
+static u8 scc_cable_detect(ide_hwif_t *hwif)
{
return ATA_CBL_PATA80;
}
return dev->irq;
}
-static u8 __devinit ata66_svwks_svwks(ide_hwif_t *hwif)
+static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
{
return ATA_CBL_PATA80;
}
* Bit 14 clear = primary IDE channel does not have 80-pin cable.
* Bit 14 set = primary IDE channel has 80-pin cable.
*/
-static u8 __devinit ata66_svwks_dell(ide_hwif_t *hwif)
+static u8 ata66_svwks_dell(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
*
* WARNING: this only works on Alpine hardware!
*/
-static u8 __devinit ata66_svwks_cobalt(ide_hwif_t *hwif)
+static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
return ATA_CBL_PATA40;
}
-static u8 __devinit svwks_cable_detect(ide_hwif_t *hwif)
+static u8 svwks_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
* that can occur before we know what drives are present.
*/
-static void __devinit sil_quirkproc(ide_drive_t *drive)
+static void sil_quirkproc(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
* Check for the presence of an ATA66 capable cable on the interface.
*/
-static u8 __devinit sil_cable_detect(ide_hwif_t *hwif)
+static u8 sil_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long addr = siimage_selreg(hwif, 0);
{ 0, }
};
-static u8 __devinit sis_cable_detect(ide_hwif_t *hwif)
+static u8 sis_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
const struct sis_laptop *lap = &sis_laptop[0];
}
}
-static u8 __devinit slc90e66_cable_detect(ide_hwif_t *hwif)
+static u8 slc90e66_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
u8 reg47 = 0, mask = hwif->channel ? 0x01 : 0x02;
ide_dma_start(drive);
}
-static u8 __devinit tc86c001_cable_detect(ide_hwif_t *hwif)
+static u8 tc86c001_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
unsigned long sc_base = pci_resource_start(dev, 5);
return 0;
}
-static u8 __devinit via82cxxx_cable_detect(ide_hwif_t *hwif)
+static u8 via82cxxx_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
struct ide_host *host = pci_get_drvdata(pdev);
/* Make sure we have sane timings */
sanitize_timings(pmif);
+ host = ide_host_alloc(&d, hws);
+ if (host == NULL)
+ return -ENOMEM;
+ hwif = host->ports[0];
+
#ifndef CONFIG_PPC64
/* XXX FIXME: Media bay stuff need re-organizing */
if (np->parent && np->parent->name
pmif->mdev ? "macio" : "PCI", pmif->aapl_bus_id,
pmif->mediabay ? " (mediabay)" : "", hw->irq);
- rc = ide_host_add(&d, hws, &host);
- if (rc)
+ rc = ide_host_register(host, &d, hws);
+ if (rc) {
+ ide_host_free(host);
return rc;
-
- hwif = host->ports[0];
+ }
return 0;
}
} multicast;
struct list_head list;
void *context;
- struct sockaddr addr;
- u8 pad[sizeof(struct sockaddr_in6) -
- sizeof(struct sockaddr)];
+ struct sockaddr_storage addr;
};
struct cma_work {
cma_cancel_route(id_priv);
break;
case CMA_LISTEN:
- if (cma_any_addr(&id_priv->id.route.addr.src_addr) &&
- !id_priv->cma_dev)
+ if (cma_any_addr((struct sockaddr *) &id_priv->id.route.addr.src_addr)
+ && !id_priv->cma_dev)
cma_cancel_listens(id_priv);
break;
default:
rt->path_rec[1] = *ib_event->param.req_rcvd.alternate_path;
ib_addr_set_dgid(&rt->addr.dev_addr, &rt->path_rec[0].dgid);
- ret = rdma_translate_ip(&id->route.addr.src_addr,
+ ret = rdma_translate_ip((struct sockaddr *) &id->route.addr.src_addr,
&id->route.addr.dev_addr);
if (ret)
goto destroy_id;
cma_save_net_info(&id->route.addr, &listen_id->route.addr,
ip_ver, port, src, dst);
- ret = rdma_translate_ip(&id->route.addr.src_addr,
+ ret = rdma_translate_ip((struct sockaddr *) &id->route.addr.src_addr,
&id->route.addr.dev_addr);
if (ret)
goto err;
if (IS_ERR(id_priv->cm_id.ib))
return PTR_ERR(id_priv->cm_id.ib);
- addr = &id_priv->id.route.addr.src_addr;
+ addr = (struct sockaddr *) &id_priv->id.route.addr.src_addr;
svc_id = cma_get_service_id(id_priv->id.ps, addr);
if (cma_any_addr(addr))
ret = ib_cm_listen(id_priv->cm_id.ib, svc_id, 0, NULL);
dev_id_priv->state = CMA_ADDR_BOUND;
memcpy(&id->route.addr.src_addr, &id_priv->id.route.addr.src_addr,
- ip_addr_size(&id_priv->id.route.addr.src_addr));
+ ip_addr_size((struct sockaddr *) &id_priv->id.route.addr.src_addr));
cma_attach_to_dev(dev_id_priv, cma_dev);
list_add_tail(&dev_id_priv->listen_list, &id_priv->listen_list);
path_rec.pkey = cpu_to_be16(ib_addr_get_pkey(&addr->dev_addr));
path_rec.numb_path = 1;
path_rec.reversible = 1;
- path_rec.service_id = cma_get_service_id(id_priv->id.ps, &addr->dst_addr);
+ path_rec.service_id = cma_get_service_id(id_priv->id.ps,
+ (struct sockaddr *) &addr->dst_addr);
comp_mask = IB_SA_PATH_REC_DGID | IB_SA_PATH_REC_SGID |
IB_SA_PATH_REC_PKEY | IB_SA_PATH_REC_NUMB_PATH |
IB_SA_PATH_REC_REVERSIBLE | IB_SA_PATH_REC_SERVICE_ID;
- if (addr->src_addr.sa_family == AF_INET) {
+ if (addr->src_addr.ss_family == AF_INET) {
path_rec.qos_class = cpu_to_be16((u16) id_priv->tos);
comp_mask |= IB_SA_PATH_REC_QOS_CLASS;
} else {
ib_addr_get_sgid(&id_priv->id.route.addr.dev_addr, &gid);
ib_addr_set_dgid(&id_priv->id.route.addr.dev_addr, &gid);
- if (cma_zero_addr(&id_priv->id.route.addr.src_addr)) {
+ if (cma_zero_addr((struct sockaddr *) &id_priv->id.route.addr.src_addr)) {
src_in = (struct sockaddr_in *)&id_priv->id.route.addr.src_addr;
dst_in = (struct sockaddr_in *)&id_priv->id.route.addr.dst_addr;
src_in->sin_family = dst_in->sin_family;
if (cma_any_addr(dst_addr))
ret = cma_resolve_loopback(id_priv);
else
- ret = rdma_resolve_ip(&addr_client, &id->route.addr.src_addr,
+ ret = rdma_resolve_ip(&addr_client, (struct sockaddr *) &id->route.addr.src_addr,
dst_addr, &id->route.addr.dev_addr,
timeout_ms, addr_handler, id_priv);
if (ret)
* We don't support binding to any address if anyone is bound to
* a specific address on the same port.
*/
- if (cma_any_addr(&id_priv->id.route.addr.src_addr))
+ if (cma_any_addr((struct sockaddr *) &id_priv->id.route.addr.src_addr))
return -EADDRNOTAVAIL;
hlist_for_each_entry(cur_id, node, &bind_list->owners, node) {
- if (cma_any_addr(&cur_id->id.route.addr.src_addr))
+ if (cma_any_addr((struct sockaddr *) &cur_id->id.route.addr.src_addr))
return -EADDRNOTAVAIL;
cur_sin = (struct sockaddr_in *) &cur_id->id.route.addr.src_addr;
}
mutex_lock(&lock);
- if (cma_any_port(&id_priv->id.route.addr.src_addr))
+ if (cma_any_port((struct sockaddr *) &id_priv->id.route.addr.src_addr))
ret = cma_alloc_any_port(ps, id_priv);
else
ret = cma_use_port(ps, id_priv);
req.path = route->path_rec;
req.service_id = cma_get_service_id(id_priv->id.ps,
- &route->addr.dst_addr);
+ (struct sockaddr *) &route->addr.dst_addr);
req.timeout_ms = 1 << (CMA_CM_RESPONSE_TIMEOUT - 8);
req.max_cm_retries = CMA_MAX_CM_RETRIES;
req.alternate_path = &route->path_rec[1];
req.service_id = cma_get_service_id(id_priv->id.ps,
- &route->addr.dst_addr);
+ (struct sockaddr *) &route->addr.dst_addr);
req.qp_num = id_priv->qp_num;
req.qp_type = IB_QPT_RC;
req.starting_psn = id_priv->seq_num;
if (ret)
return ret;
- cma_set_mgid(id_priv, &mc->addr, &rec.mgid);
+ cma_set_mgid(id_priv, (struct sockaddr *) &mc->addr, &rec.mgid);
if (id_priv->id.ps == RDMA_PS_UDP)
rec.qkey = cpu_to_be32(RDMA_UDP_QKEY);
ib_addr_get_sgid(dev_addr, &rec.port_gid);
msg = ib_create_send_mad(&rmpp_recv->agent->agent, recv_wc->wc->src_qp,
recv_wc->wc->pkey_index, 1, hdr_len,
0, GFP_KERNEL);
- if (!msg)
+ if (IS_ERR(msg))
return;
format_ack(msg, (struct ib_rmpp_mad *) recv_wc->recv_buf.mad, rmpp_recv);
u64 uid;
struct list_head list;
- struct sockaddr addr;
- u8 pad[sizeof(struct sockaddr_in6) -
- sizeof(struct sockaddr)];
+ struct sockaddr_storage addr;
};
struct ucma_event {
return PTR_ERR(ctx);
memset(&resp, 0, sizeof resp);
- addr = &ctx->cm_id->route.addr.src_addr;
+ addr = (struct sockaddr *) &ctx->cm_id->route.addr.src_addr;
memcpy(&resp.src_addr, addr, addr->sa_family == AF_INET ?
sizeof(struct sockaddr_in) :
sizeof(struct sockaddr_in6));
- addr = &ctx->cm_id->route.addr.dst_addr;
+ addr = (struct sockaddr *) &ctx->cm_id->route.addr.dst_addr;
memcpy(&resp.dst_addr, addr, addr->sa_family == AF_INET ?
sizeof(struct sockaddr_in) :
sizeof(struct sockaddr_in6));
mc->uid = cmd.uid;
memcpy(&mc->addr, &cmd.addr, sizeof cmd.addr);
- ret = rdma_join_multicast(ctx->cm_id, &mc->addr, mc);
+ ret = rdma_join_multicast(ctx->cm_id, (struct sockaddr *) &mc->addr, mc);
if (ret)
goto err2;
return 0;
err3:
- rdma_leave_multicast(ctx->cm_id, &mc->addr);
+ rdma_leave_multicast(ctx->cm_id, (struct sockaddr *) &mc->addr);
ucma_cleanup_mc_events(mc);
err2:
mutex_lock(&mut);
goto out;
}
- rdma_leave_multicast(mc->ctx->cm_id, &mc->addr);
+ rdma_leave_multicast(mc->ctx->cm_id, (struct sockaddr *) &mc->addr);
mutex_lock(&mc->ctx->file->mut);
ucma_cleanup_mc_events(mc);
list_del(&mc->list);
V_TPT_STAG_TYPE(type) | V_TPT_PDID(pdid));
BUG_ON(page_size >= 28);
tpt.flags_pagesize_qpid = cpu_to_be32(V_TPT_PERM(perm) |
- F_TPT_MW_BIND_ENABLE |
- V_TPT_ADDR_TYPE((zbva ? TPT_ZBTO : TPT_VATO)) |
- V_TPT_PAGE_SIZE(page_size));
+ ((perm & TPT_MW_BIND) ? F_TPT_MW_BIND_ENABLE : 0) |
+ V_TPT_ADDR_TYPE((zbva ? TPT_ZBTO : TPT_VATO)) |
+ V_TPT_PAGE_SIZE(page_size));
tpt.rsvd_pbl_addr = reset_tpt_entry ? 0 :
cpu_to_be32(V_TPT_PBL_ADDR(PBL_OFF(rdev_p, pbl_addr)>>3));
tpt.len = cpu_to_be32(len);
return sprintf(buf, "%d\n", iwch_dev->rdev.t3cdev_p->type);
}
-static int fw_supports_fastreg(struct iwch_dev *iwch_dev)
-{
- struct ethtool_drvinfo info;
- struct net_device *lldev = iwch_dev->rdev.t3cdev_p->lldev;
- char *cp, *next;
- unsigned fw_maj, fw_min;
-
- rtnl_lock();
- lldev->ethtool_ops->get_drvinfo(lldev, &info);
- rtnl_unlock();
-
- next = info.fw_version+1;
- cp = strsep(&next, ".");
- sscanf(cp, "%i", &fw_maj);
- cp = strsep(&next, ".");
- sscanf(cp, "%i", &fw_min);
-
- PDBG("%s maj %u min %u\n", __func__, fw_maj, fw_min);
-
- return fw_maj > 6 || (fw_maj == 6 && fw_min > 0);
-}
-
static ssize_t show_fw_ver(struct device *dev, struct device_attribute *attr, char *buf)
{
struct iwch_dev *iwch_dev = container_of(dev, struct iwch_dev,
memset(&dev->ibdev.node_guid, 0, sizeof(dev->ibdev.node_guid));
memcpy(&dev->ibdev.node_guid, dev->rdev.t3cdev_p->lldev->dev_addr, 6);
dev->ibdev.owner = THIS_MODULE;
- dev->device_cap_flags = IB_DEVICE_LOCAL_DMA_LKEY | IB_DEVICE_MEM_WINDOW;
+ dev->device_cap_flags = IB_DEVICE_LOCAL_DMA_LKEY |
+ IB_DEVICE_MEM_WINDOW |
+ IB_DEVICE_MEM_MGT_EXTENSIONS;
/* cxgb3 supports STag 0. */
dev->ibdev.local_dma_lkey = 0;
- if (fw_supports_fastreg(dev))
- dev->device_cap_flags |= IB_DEVICE_MEM_MGT_EXTENSIONS;
dev->ibdev.uverbs_cmd_mask =
(1ull << IB_USER_VERBS_CMD_GET_CONTEXT) |
return (acc & IB_ACCESS_REMOTE_WRITE ? TPT_REMOTE_WRITE : 0) |
(acc & IB_ACCESS_REMOTE_READ ? TPT_REMOTE_READ : 0) |
(acc & IB_ACCESS_LOCAL_WRITE ? TPT_LOCAL_WRITE : 0) |
+ (acc & IB_ACCESS_MW_BIND ? TPT_MW_BIND : 0) |
TPT_LOCAL_READ;
}
+static inline u32 iwch_ib_to_tpt_bind_access(int acc)
+{
+ return (acc & IB_ACCESS_REMOTE_WRITE ? TPT_REMOTE_WRITE : 0) |
+ (acc & IB_ACCESS_REMOTE_READ ? TPT_REMOTE_READ : 0);
+}
+
enum iwch_mmid_state {
IWCH_STAG_STATE_VALID,
IWCH_STAG_STATE_INVALID
wqe->bind.type = TPT_VATO;
/* TBD: check perms */
- wqe->bind.perms = iwch_ib_to_tpt_access(mw_bind->mw_access_flags);
+ wqe->bind.perms = iwch_ib_to_tpt_bind_access(mw_bind->mw_access_flags);
wqe->bind.mr_stag = cpu_to_be32(mw_bind->mr->lkey);
wqe->bind.mw_stag = cpu_to_be32(mw->rkey);
wqe->bind.mw_len = cpu_to_be32(mw_bind->length);
(qhp->attr.mpa_attr.xmit_marker_enabled << 1) |
(qhp->attr.mpa_attr.crc_enabled << 2);
- /*
- * XXX - The IWCM doesn't quite handle getting these
- * attrs set before going into RTS. For now, just turn
- * them on always...
- */
-#if 0
- init_attr.qpcaps = qhp->attr.enableRdmaRead |
- (qhp->attr.enableRdmaWrite << 1) |
- (qhp->attr.enableBind << 2) |
- (qhp->attr.enable_stag0_fastreg << 3) |
- (qhp->attr.enable_stag0_fastreg << 4);
-#else
- init_attr.qpcaps = 0x1f;
-#endif
+ init_attr.qpcaps = uP_RI_QP_RDMA_READ_ENABLE |
+ uP_RI_QP_RDMA_WRITE_ENABLE |
+ uP_RI_QP_BIND_ENABLE;
+ if (!qhp->ibqp.uobject)
+ init_attr.qpcaps |= uP_RI_QP_STAG0_ENABLE |
+ uP_RI_QP_FAST_REGISTER_ENABLE;
+
init_attr.tcp_emss = qhp->ep->emss;
init_attr.ord = qhp->attr.max_ord;
init_attr.ird = qhp->attr.max_ird;
init_attr.qp_dma_size = (1UL << qhp->wq.size_log2);
init_attr.rqe_count = iwch_rqes_posted(qhp);
init_attr.flags = qhp->attr.mpa_attr.initiator ? MPA_INITIATOR : 0;
- if (!qhp->ibqp.uobject)
- init_attr.flags |= PRIV_QP;
if (peer2peer) {
init_attr.rtr_type = RTR_READ;
if (init_attr.ord == 0 && qhp->attr.mpa_attr.initiator)
*/
-#include <asm-powerpc/system.h>
+#include <asm/system.h>
#include "ehca_classes.h"
#include "ehca_tools.h"
#include "ehca_qes.h"
*/
ipath_cdbg(ERRPKT, "Error Pkt, but no eflags! egrbuf"
" %x, len %x hdrq+%x rhf: %Lx\n",
- etail, tlen, l,
+ etail, tlen, l, (unsigned long long)
le64_to_cpu(*(__le64 *) rhf_addr));
if (ipath_debug & __IPATH_ERRPKTDBG) {
u32 j, *d, dw = rsize-2;
0xaaaaaaaaaaaaaaaaULL); /* All BUSY bits in qword */
if (oldval != dd->ipath_pioavailshadow[i])
ipath_dbg("shadow[%d] was %Lx, now %lx\n",
- i, oldval, dd->ipath_pioavailshadow[i]);
+ i, (unsigned long long) oldval,
+ dd->ipath_pioavailshadow[i]);
}
spin_unlock_irqrestore(&ipath_pioavail_lock, flags);
}
static char int_type[16] = "auto";
module_param_string(interrupt_type, int_type, sizeof(int_type), 0444);
-MODULE_PARM_DESC(int_type, " interrupt_type=auto|force_msi|force_intx\n");
+MODULE_PARM_DESC(int_type, " interrupt_type=auto|force_msi|force_intx");
/* packet rate matching delay; chip has support */
static u8 rate_to_delay[2][2] = {
ipath_cdbg(VERBOSE, "done: xgxs=%llx from %llx\n",
(unsigned long long)
ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig),
- prev_val);
+ (unsigned long long) prev_val);
guid = be64_to_cpu(dd->ipath_guid);
ipath_dbg("No GUID for heartbeat, faking %llx\n",
(unsigned long long)guid);
} else
- ipath_cdbg(VERBOSE, "Wrote %llX to HRTBT_GUID\n", guid);
+ ipath_cdbg(VERBOSE, "Wrote %llX to HRTBT_GUID\n",
+ (unsigned long long) guid);
ipath_write_kreg(dd, dd->ipath_kregs->kr_hrtbt_guid, guid);
return ret;
}
if (dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) {
ipath_dbg("Did not get to DDR INIT (%x) after %Lu msecs\n",
ipath_ib_state(dd, dd->ipath_lastibcstat),
- jiffies_to_msecs(jiffies)-startms);
+ (unsigned long long) jiffies_to_msecs(jiffies)-startms);
dd->ipath_flags &= ~IPATH_IB_AUTONEG_INPROG;
if (dd->ipath_autoneg_tries == IPATH_AUTONEG_TRIES) {
dd->ipath_flags |= IPATH_IB_AUTONEG_FAILED;
dd->ipath_cregs->cr_iblinkerrrecovcnt);
if (linkrecov != dd->ipath_lastlinkrecov) {
ipath_dbg("IB linkrecov up %Lx (%s %s) recov %Lu\n",
- ibcs, ib_linkstate(dd, ibcs),
+ (unsigned long long) ibcs,
+ ib_linkstate(dd, ibcs),
ipath_ibcstatus_str[ltstate],
- linkrecov);
+ (unsigned long long) linkrecov);
/* and no more until active again */
dd->ipath_lastlinkrecov = 0;
ipath_set_linkstate(dd, IPATH_IB_LINKDOWN);
if (unlikely(istat & ~dd->ipath_i_bitsextant))
ipath_dev_err(dd,
"interrupt with unknown interrupts %Lx set\n",
+ (unsigned long long)
istat & ~dd->ipath_i_bitsextant);
else if (istat & ~INFINIPATH_I_ERROR) /* errors do own printing */
- ipath_cdbg(VERBOSE, "intr stat=0x%Lx\n", istat);
+ ipath_cdbg(VERBOSE, "intr stat=0x%Lx\n",
+ (unsigned long long) istat);
if (istat & INFINIPATH_I_ERROR) {
ipath_stats.sps_errints++;
dd->ipath_kregs->kr_errorstatus);
if (!estat)
dev_info(&dd->pcidev->dev, "error interrupt (%Lx), "
- "but no error bits set!\n", istat);
+ "but no error bits set!\n",
+ (unsigned long long) istat);
else if (estat == -1LL)
/*
* should we try clearing all, or hope next read
struct ipath_verbs_txreq *tx = cookie;
struct ipath_qp *qp = tx->qp;
struct ipath_ibdev *dev = to_idev(qp->ibqp.device);
- unsigned int flags;
+ unsigned long flags;
enum ib_wc_status ibs = status == IPATH_SDMA_TXREQ_S_OK ?
IB_WC_SUCCESS : IB_WC_WR_FLUSH_ERR;
static void decrement_dma_busy(struct ipath_qp *qp)
{
- unsigned int flags;
+ unsigned long flags;
if (atomic_dec_and_test(&qp->s_dma_busy)) {
spin_lock_irqsave(&qp->s_lock, flags);
unsigned flush_wc;
u32 control;
int ret;
- unsigned int flags;
+ unsigned long flags;
piobuf = ipath_getpiobuf(dd, plen, NULL);
if (unlikely(piobuf == NULL)) {
wc->vendor_err = cqe->vendor_err_syndrome;
}
-static int mlx4_ib_ipoib_csum_ok(__be32 status, __be16 checksum)
+static int mlx4_ib_ipoib_csum_ok(__be16 status, __be16 checksum)
{
- return ((status & cpu_to_be32(MLX4_CQE_IPOIB_STATUS_IPV4 |
- MLX4_CQE_IPOIB_STATUS_IPV4F |
- MLX4_CQE_IPOIB_STATUS_IPV4OPT |
- MLX4_CQE_IPOIB_STATUS_IPV6 |
- MLX4_CQE_IPOIB_STATUS_IPOK)) ==
- cpu_to_be32(MLX4_CQE_IPOIB_STATUS_IPV4 |
- MLX4_CQE_IPOIB_STATUS_IPOK)) &&
- (status & cpu_to_be32(MLX4_CQE_IPOIB_STATUS_UDP |
- MLX4_CQE_IPOIB_STATUS_TCP)) &&
+ return ((status & cpu_to_be16(MLX4_CQE_STATUS_IPV4 |
+ MLX4_CQE_STATUS_IPV4F |
+ MLX4_CQE_STATUS_IPV4OPT |
+ MLX4_CQE_STATUS_IPV6 |
+ MLX4_CQE_STATUS_IPOK)) ==
+ cpu_to_be16(MLX4_CQE_STATUS_IPV4 |
+ MLX4_CQE_STATUS_IPOK)) &&
+ (status & cpu_to_be16(MLX4_CQE_STATUS_UDP |
+ MLX4_CQE_STATUS_TCP)) &&
checksum == cpu_to_be16(0xffff);
}
}
if (!*cur_qp ||
- (be32_to_cpu(cqe->my_qpn) & 0xffffff) != (*cur_qp)->mqp.qpn) {
+ (be32_to_cpu(cqe->vlan_my_qpn) & MLX4_CQE_QPN_MASK) != (*cur_qp)->mqp.qpn) {
/*
* We do not have to take the QP table lock here,
* because CQs will be locked while QPs are removed
* from the table.
*/
mqp = __mlx4_qp_lookup(to_mdev(cq->ibcq.device)->dev,
- be32_to_cpu(cqe->my_qpn));
+ be32_to_cpu(cqe->vlan_my_qpn));
if (unlikely(!mqp)) {
printk(KERN_WARNING "CQ %06x with entry for unknown QPN %06x\n",
- cq->mcq.cqn, be32_to_cpu(cqe->my_qpn) & 0xffffff);
+ cq->mcq.cqn, be32_to_cpu(cqe->vlan_my_qpn) & MLX4_CQE_QPN_MASK);
return -EINVAL;
}
}
wc->slid = be16_to_cpu(cqe->rlid);
- wc->sl = cqe->sl >> 4;
+ wc->sl = be16_to_cpu(cqe->sl_vid >> 12);
g_mlpath_rqpn = be32_to_cpu(cqe->g_mlpath_rqpn);
wc->src_qp = g_mlpath_rqpn & 0xffffff;
wc->dlid_path_bits = (g_mlpath_rqpn >> 24) & 0x7f;
wc->wc_flags |= g_mlpath_rqpn & 0x80000000 ? IB_WC_GRH : 0;
wc->pkey_index = be32_to_cpu(cqe->immed_rss_invalid) & 0x7f;
- wc->csum_ok = mlx4_ib_ipoib_csum_ok(cqe->ipoib_status,
- cqe->checksum);
+ wc->csum_ok = mlx4_ib_ipoib_csum_ok(cqe->status, cqe->checksum);
}
return 0;
*/
while ((int) --prod_index - (int) cq->mcq.cons_index >= 0) {
cqe = get_cqe(cq, prod_index & cq->ibcq.cqe);
- if ((be32_to_cpu(cqe->my_qpn) & 0xffffff) == qpn) {
+ if ((be32_to_cpu(cqe->vlan_my_qpn) & MLX4_CQE_QPN_MASK) == qpn) {
if (srq && !(cqe->owner_sr_opcode & MLX4_CQE_IS_SEND_MASK))
mlx4_ib_free_srq_wqe(srq, be16_to_cpu(cqe->wqe_index));
++nfreed;
context->mtu_msgmax = (IB_MTU_4096 << 5) |
ilog2(dev->dev->caps.max_gso_sz);
else
- context->mtu_msgmax = (IB_MTU_4096 << 5) | 11;
+ context->mtu_msgmax = (IB_MTU_4096 << 5) | 12;
} else if (attr_mask & IB_QP_PATH_MTU) {
if (attr->path_mtu < IB_MTU_256 || attr->path_mtu > IB_MTU_4096) {
printk(KERN_ERR "path MTU (%u) is invalid\n",
sge[i].length = PAGE_SIZE;
wr->next = NULL;
- wr->sg_list = priv->cm.rx_sge;
+ wr->sg_list = sge;
wr->num_sge = priv->cm.num_frags;
}
#include <linux/module.h>
#include <linux/slab.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/aaed2000.h>
+#include <mach/hardware.h>
+#include <mach/aaed2000.h>
#define KB_ROWS 12
#define KB_COLS 8
#include <linux/module.h>
#include <linux/slab.h>
-#include <asm/arch/corgi.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/corgi.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
#include <asm/hardware/scoop.h>
#define KB_ROWS 8
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/arch/jornada720.h>
-#include <asm/hardware.h>
+#include <mach/jornada720.h>
+#include <mach/hardware.h>
MODULE_AUTHOR("Kristoffer Ericson <Kristoffer.Ericson@gmail.com>");
MODULE_DESCRIPTION("HP Jornada 710/720/728 keyboard driver");
* SEGA Dreamcast keyboard driver
* Based on drivers/usb/usbkbd.c
* Copyright YAEGASHI Takeshi, 2001
- * Porting to 2.6 Copyright Adrian McMenamin, 2007
+ * Porting to 2.6 Copyright Adrian McMenamin, 2007, 2008
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <linux/init.h>
#include <linux/timer.h>
#include <linux/maple.h>
-#include <asm/mach/maple.h>
/* Very simple mutex to ensure proper cleanup */
static DEFINE_MUTEX(maple_keyb_mutex);
};
static const unsigned short dc_kbd_keycode[NR_SCANCODES] = {
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_A, KEY_B, KEY_C, KEY_D,
- KEY_E, KEY_F, KEY_G, KEY_H, KEY_I, KEY_J, KEY_K, KEY_L,
- KEY_M, KEY_N, KEY_O, KEY_P, KEY_Q, KEY_R, KEY_S, KEY_T,
- KEY_U, KEY_V, KEY_W, KEY_X, KEY_Y, KEY_Z, KEY_1, KEY_2,
- KEY_3, KEY_4, KEY_5, KEY_6, KEY_7, KEY_8, KEY_9, KEY_0,
- KEY_ENTER, KEY_ESC, KEY_BACKSPACE, KEY_TAB, KEY_SPACE, KEY_MINUS, KEY_EQUAL, KEY_LEFTBRACE,
- KEY_RIGHTBRACE, KEY_BACKSLASH, KEY_BACKSLASH, KEY_SEMICOLON, KEY_APOSTROPHE, KEY_GRAVE, KEY_COMMA,
- KEY_DOT, KEY_SLASH, KEY_CAPSLOCK, KEY_F1, KEY_F2, KEY_F3, KEY_F4, KEY_F5, KEY_F6,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_A, KEY_B,
+ KEY_C, KEY_D, KEY_E, KEY_F, KEY_G, KEY_H, KEY_I, KEY_J, KEY_K, KEY_L,
+ KEY_M, KEY_N, KEY_O, KEY_P, KEY_Q, KEY_R, KEY_S, KEY_T, KEY_U, KEY_V,
+ KEY_W, KEY_X, KEY_Y, KEY_Z, KEY_1, KEY_2, KEY_3, KEY_4, KEY_5, KEY_6,
+ KEY_7, KEY_8, KEY_9, KEY_0, KEY_ENTER, KEY_ESC, KEY_BACKSPACE,
+ KEY_TAB, KEY_SPACE, KEY_MINUS, KEY_EQUAL, KEY_LEFTBRACE,
+ KEY_RIGHTBRACE, KEY_BACKSLASH, KEY_BACKSLASH, KEY_SEMICOLON,
+ KEY_APOSTROPHE, KEY_GRAVE, KEY_COMMA, KEY_DOT, KEY_SLASH,
+ KEY_CAPSLOCK, KEY_F1, KEY_F2, KEY_F3, KEY_F4, KEY_F5, KEY_F6,
KEY_F7, KEY_F8, KEY_F9, KEY_F10, KEY_F11, KEY_F12, KEY_SYSRQ,
- KEY_SCROLLLOCK, KEY_PAUSE, KEY_INSERT, KEY_HOME, KEY_PAGEUP, KEY_DELETE,
- KEY_END, KEY_PAGEDOWN, KEY_RIGHT, KEY_LEFT, KEY_DOWN, KEY_UP,
- KEY_NUMLOCK, KEY_KPSLASH, KEY_KPASTERISK, KEY_KPMINUS, KEY_KPPLUS, KEY_KPENTER, KEY_KP1, KEY_KP2,
- KEY_KP3, KEY_KP4, KEY_KP5, KEY_KP6, KEY_KP7, KEY_KP8, KEY_KP9, KEY_KP0, KEY_KPDOT,
- KEY_102ND, KEY_COMPOSE, KEY_POWER, KEY_KPEQUAL, KEY_F13, KEY_F14, KEY_F15,
- KEY_F16, KEY_F17, KEY_F18, KEY_F19, KEY_F20,
- KEY_F21, KEY_F22, KEY_F23, KEY_F24, KEY_OPEN, KEY_HELP, KEY_PROPS, KEY_FRONT,
- KEY_STOP, KEY_AGAIN, KEY_UNDO, KEY_CUT, KEY_COPY, KEY_PASTE, KEY_FIND, KEY_MUTE,
- KEY_VOLUMEUP, KEY_VOLUMEDOWN, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_KPCOMMA, KEY_RESERVED, KEY_RO, KEY_KATAKANAHIRAGANA , KEY_YEN,
- KEY_HENKAN, KEY_MUHENKAN, KEY_KPJPCOMMA, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_HANGEUL, KEY_HANJA, KEY_KATAKANA, KEY_HIRAGANA, KEY_ZENKAKUHANKAKU, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
- KEY_LEFTCTRL, KEY_LEFTSHIFT, KEY_LEFTALT, KEY_LEFTMETA, KEY_RIGHTCTRL, KEY_RIGHTSHIFT, KEY_RIGHTALT, KEY_RIGHTMETA,
- KEY_PLAYPAUSE, KEY_STOPCD, KEY_PREVIOUSSONG, KEY_NEXTSONG, KEY_EJECTCD, KEY_VOLUMEUP, KEY_VOLUMEDOWN, KEY_MUTE,
- KEY_WWW, KEY_BACK, KEY_FORWARD, KEY_STOP, KEY_FIND, KEY_SCROLLUP, KEY_SCROLLDOWN, KEY_EDIT, KEY_SLEEP,
- KEY_SCREENLOCK, KEY_REFRESH, KEY_CALC, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED
+ KEY_SCROLLLOCK, KEY_PAUSE, KEY_INSERT, KEY_HOME, KEY_PAGEUP,
+ KEY_DELETE, KEY_END, KEY_PAGEDOWN, KEY_RIGHT, KEY_LEFT, KEY_DOWN,
+ KEY_UP, KEY_NUMLOCK, KEY_KPSLASH, KEY_KPASTERISK, KEY_KPMINUS,
+ KEY_KPPLUS, KEY_KPENTER, KEY_KP1, KEY_KP2, KEY_KP3, KEY_KP4, KEY_KP5,
+ KEY_KP6, KEY_KP7, KEY_KP8, KEY_KP9, KEY_KP0, KEY_KPDOT, KEY_102ND,
+ KEY_COMPOSE, KEY_POWER, KEY_KPEQUAL, KEY_F13, KEY_F14, KEY_F15,
+ KEY_F16, KEY_F17, KEY_F18, KEY_F19, KEY_F20, KEY_F21, KEY_F22,
+ KEY_F23, KEY_F24, KEY_OPEN, KEY_HELP, KEY_PROPS, KEY_FRONT, KEY_STOP,
+ KEY_AGAIN, KEY_UNDO, KEY_CUT, KEY_COPY, KEY_PASTE, KEY_FIND, KEY_MUTE,
+ KEY_VOLUMEUP, KEY_VOLUMEDOWN, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_KPCOMMA, KEY_RESERVED, KEY_RO, KEY_KATAKANAHIRAGANA , KEY_YEN,
+ KEY_HENKAN, KEY_MUHENKAN, KEY_KPJPCOMMA, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_HANGEUL, KEY_HANJA, KEY_KATAKANA, KEY_HIRAGANA,
+ KEY_ZENKAKUHANKAKU, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED,
+ KEY_RESERVED, KEY_RESERVED, KEY_LEFTCTRL, KEY_LEFTSHIFT, KEY_LEFTALT,
+ KEY_LEFTMETA, KEY_RIGHTCTRL, KEY_RIGHTSHIFT, KEY_RIGHTALT,
+ KEY_RIGHTMETA, KEY_PLAYPAUSE, KEY_STOPCD, KEY_PREVIOUSSONG,
+ KEY_NEXTSONG, KEY_EJECTCD, KEY_VOLUMEUP, KEY_VOLUMEDOWN, KEY_MUTE,
+ KEY_WWW, KEY_BACK, KEY_FORWARD, KEY_STOP, KEY_FIND, KEY_SCROLLUP,
+ KEY_SCROLLDOWN, KEY_EDIT, KEY_SLEEP, KEY_SCREENLOCK, KEY_REFRESH,
+ KEY_CALC, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED, KEY_RESERVED
};
static void dc_scan_kbd(struct dc_kbd *kbd)
static void dc_kbd_callback(struct mapleq *mq)
{
struct maple_device *mapledev = mq->dev;
- struct dc_kbd *kbd = mapledev->private_data;
+ struct dc_kbd *kbd = maple_get_drvdata(mapledev);
unsigned long *buf = mq->recvbuf;
/*
- * We should always be getting the lock because the only
- * time it may be locked if driver is in cleanup phase.
+ * We should always get the lock because the only
+ * time it may be locked is if the driver is in the cleanup phase.
*/
if (likely(mutex_trylock(&maple_keyb_mutex))) {
}
}
-static int dc_kbd_connect(struct maple_device *mdev)
+static int probe_maple_kbd(struct device *dev)
{
+ struct maple_device *mdev = to_maple_dev(dev);
+ struct maple_driver *mdrv = to_maple_driver(dev->driver);
int i, error;
struct dc_kbd *kbd;
- struct input_dev *dev;
+ struct input_dev *idev;
if (!(mdev->function & MAPLE_FUNC_KEYBOARD))
return -EINVAL;
kbd = kzalloc(sizeof(struct dc_kbd), GFP_KERNEL);
- dev = input_allocate_device();
- if (!kbd || !dev) {
+ idev = input_allocate_device();
+ if (!kbd || !idev) {
error = -ENOMEM;
goto fail;
}
- mdev->private_data = kbd;
-
- kbd->dev = dev;
+ kbd->dev = idev;
memcpy(kbd->keycode, dc_kbd_keycode, sizeof(kbd->keycode));
- dev->name = mdev->product_name;
- dev->evbit[0] = BIT(EV_KEY) | BIT(EV_REP);
- dev->keycode = kbd->keycode;
- dev->keycodesize = sizeof (unsigned short);
- dev->keycodemax = ARRAY_SIZE(kbd->keycode);
- dev->id.bustype = BUS_HOST;
- dev->dev.parent = &mdev->dev;
+ idev->name = mdev->product_name;
+ idev->evbit[0] = BIT(EV_KEY) | BIT(EV_REP);
+ idev->keycode = kbd->keycode;
+ idev->keycodesize = sizeof(unsigned short);
+ idev->keycodemax = ARRAY_SIZE(kbd->keycode);
+ idev->id.bustype = BUS_HOST;
+ idev->dev.parent = &mdev->dev;
for (i = 0; i < NR_SCANCODES; i++)
- __set_bit(dc_kbd_keycode[i], dev->keybit);
- __clear_bit(KEY_RESERVED, dev->keybit);
+ __set_bit(dc_kbd_keycode[i], idev->keybit);
+ __clear_bit(KEY_RESERVED, idev->keybit);
- input_set_capability(dev, EV_MSC, MSC_SCAN);
- input_set_drvdata(dev, kbd);
+ input_set_capability(idev, EV_MSC, MSC_SCAN);
+ input_set_drvdata(idev, kbd);
- error = input_register_device(dev);
+ error = input_register_device(idev);
if (error)
goto fail;
/* Maple polling is locked to VBLANK - which may be just 50/s */
- maple_getcond_callback(mdev, dc_kbd_callback, HZ/50, MAPLE_FUNC_KEYBOARD);
- return 0;
+ maple_getcond_callback(mdev, dc_kbd_callback, HZ/50,
+ MAPLE_FUNC_KEYBOARD);
- fail:
- input_free_device(dev);
+ mdev->driver = mdrv;
+
+ maple_set_drvdata(mdev, kbd);
+
+ return error;
+
+fail:
+ input_free_device(idev);
kfree(kbd);
- mdev->private_data = NULL;
+ maple_set_drvdata(mdev, NULL);
return error;
}
-static void dc_kbd_disconnect(struct maple_device *mdev)
+static int remove_maple_kbd(struct device *dev)
{
- struct dc_kbd *kbd;
+ struct maple_device *mdev = to_maple_dev(dev);
+ struct dc_kbd *kbd = maple_get_drvdata(mdev);
mutex_lock(&maple_keyb_mutex);
- kbd = mdev->private_data;
- mdev->private_data = NULL;
input_unregister_device(kbd->dev);
kfree(kbd);
- mutex_unlock(&maple_keyb_mutex);
-}
-
-/* allow the keyboard to be used */
-static int probe_maple_kbd(struct device *dev)
-{
- struct maple_device *mdev = to_maple_dev(dev);
- struct maple_driver *mdrv = to_maple_driver(dev->driver);
- int error;
-
- error = dc_kbd_connect(mdev);
- if (error)
- return error;
-
- mdev->driver = mdrv;
- mdev->registered = 1;
+ maple_set_drvdata(mdev, NULL);
+ mutex_unlock(&maple_keyb_mutex);
return 0;
}
static struct maple_driver dc_kbd_driver = {
.function = MAPLE_FUNC_KEYBOARD,
- .connect = dc_kbd_connect,
- .disconnect = dc_kbd_disconnect,
.drv = {
.name = "Dreamcast_keyboard",
.probe = probe_maple_kbd,
- },
+ .remove = remove_maple_kbd,
+ },
};
static int __init dc_kbd_init(void)
{
- return maple_driver_register(&dc_kbd_driver.drv);
+ return maple_driver_register(&dc_kbd_driver);
}
static void __exit dc_kbd_exit(void)
{
- driver_unregister(&dc_kbd_driver.drv);
+ maple_driver_unregister(&dc_kbd_driver);
}
module_init(dc_kbd_init);
#include <linux/platform_device.h>
#include <linux/mutex.h>
#include <linux/errno.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/keypad.h>
-#include <asm/arch/menelaus.h>
+#include <mach/gpio.h>
+#include <mach/keypad.h>
+#include <mach/menelaus.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/arch/mux.h>
+#include <mach/mux.h>
#undef NEW_BOARD_LEARNING_MODE
#include <linux/clk.h>
#include <linux/err.h>
-#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa27x_keypad.h>
+#include <mach/hardware.h>
+#include <mach/pxa27x_keypad.h>
/*
* Keypad Controller registers
#include <linux/module.h>
#include <linux/slab.h>
-#include <asm/arch/spitz.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/spitz.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
#define KB_ROWS 7
#define KB_COLS 11
#include <linux/delay.h>
#include <linux/interrupt.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/tosa.h>
+#include <mach/gpio.h>
+#include <mach/tosa.h>
#define KB_ROWMASK(r) (1 << (r))
#define SCANCODE(r, c) (((r)<<4) + (c) + 1)
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
MODULE_DESCRIPTION("ixp4xx beeper driver");
#include <linux/init.h>
#include <linux/input.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/hardware/iomd.h>
writeb(val, kbd_iobase + 0x64UL);
}
+#ifdef CONFIG_PCI
+
#define OBP_PS2KBD_NAME1 "kb_ps2"
#define OBP_PS2KBD_NAME2 "keyboard"
#define OBP_PS2MS_NAME1 "kdmouse"
static int __init i8042_platform_init(void)
{
-#ifndef CONFIG_PCI
- return -ENODEV;
-#else
struct device_node *root = of_find_node_by_path("/");
if (!strcmp(root->name, "SUNW,JavaStation-1")) {
i8042_reset = 1;
return 0;
-#endif /* CONFIG_PCI */
}
static inline void i8042_platform_exit(void)
{
-#ifdef CONFIG_PCI
struct device_node *root = of_find_node_by_path("/");
if (strcmp(root->name, "SUNW,JavaStation-1"))
of_unregister_driver(&sparc_i8042_driver);
-#endif
}
+#else /* !CONFIG_PCI */
+static int __init i8042_platform_init(void)
+{
+ return -ENODEV;
+}
+
+static inline void i8042_platform_exit(void)
+{
+}
+#endif /* !CONFIG_PCI */
+
#endif /* _I8042_SPARCIO_H */
#include <linux/platform_device.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/hardware/iomd.h>
#include <asm/system.h>
#include <linux/slab.h>
#include <linux/irq.h>
-#include <asm/arch/sharpsl.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <mach/sharpsl.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
#define PWR_MODE_ACTIVE 0
#include <linux/delay.h>
/* SA1100 serial defines */
-#include <asm/arch/hardware.h>
-#include <asm/arch/irqs.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
#define DRIVER_DESC "H3600 touchscreen driver"
#include <linux/interrupt.h>
#include <linux/module.h>
-#include <asm/hardware.h>
-#include <asm/arch/jornada720.h>
+#include <mach/hardware.h>
+#include <mach/jornada720.h>
MODULE_AUTHOR("Kristoffer Ericson <kristoffer.ericson@gmail.com>");
MODULE_DESCRIPTION("HP Jornada 710/720/728 touchscreen driver");
#include <linux/interrupt.h>
#include <linux/wm97xx.h>
#include <linux/io.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#define VERSION "0.13"
obj-$(CONFIG_ISDN_I4L) += i4l/
obj-$(CONFIG_ISDN_CAPI) += capi/
obj-$(CONFIG_MISDN) += mISDN/
-obj-$(CONFIG_ISDN_CAPI) += hardware/
+obj-$(CONFIG_ISDN) += hardware/
obj-$(CONFIG_ISDN_DIVERSION) += divert/
obj-$(CONFIG_ISDN_DRV_HISAX) += hisax/
obj-$(CONFIG_ISDN_DRV_ICN) += icn/
#ifdef CONFIG_GIGASET_DEBUG
unsigned char c;
static char dbgline[3 * 32 + 1];
- static const char hexdigit[] = "0123456789abcdef";
int i = 0;
while (count-- > 0) {
if (i > sizeof(dbgline) - 4) {
c = *bytes++;
dbgline[i] = (i && !(i % 12)) ? '-' : ' ';
i++;
- dbgline[i++] = hexdigit[(c >> 4) & 0x0f];
- dbgline[i++] = hexdigit[c & 0x0f];
+ dbgline[i++] = hex_asc_hi(c);
+ dbgline[i++] = hex_asc_lo(c);
}
dbgline[i] = '\0';
gig_dbg(level, "%s:%s", tag, dbgline);
* #define HFC_REGISTER_DEBUG
*/
-static const char *hfcmulti_revision = "2.00";
+static const char *hfcmulti_revision = "2.02";
#include <linux/module.h>
#include <linux/pci.h>
{
outb(A_FIFO_DATA0, (hc->pci_iobase)+4);
while (len>>2) {
- outl(*(u32 *)data, hc->pci_iobase);
+ outl(cpu_to_le32(*(u32 *)data), hc->pci_iobase);
data += 4;
len -= 4;
}
while (len>>1) {
- outw(*(u16 *)data, hc->pci_iobase);
+ outw(cpu_to_le16(*(u16 *)data), hc->pci_iobase);
data += 2;
len -= 2;
}
write_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len)
{
while (len>>2) {
- writel(*(u32 *)data, (hc->pci_membase)+A_FIFO_DATA0);
+ writel(cpu_to_le32(*(u32 *)data),
+ hc->pci_membase + A_FIFO_DATA0);
data += 4;
len -= 4;
}
while (len>>1) {
- writew(*(u16 *)data, (hc->pci_membase)+A_FIFO_DATA0);
+ writew(cpu_to_le16(*(u16 *)data),
+ hc->pci_membase + A_FIFO_DATA0);
data += 2;
len -= 2;
}
while (len) {
- writeb(*data, (hc->pci_membase)+A_FIFO_DATA0);
+ writeb(*data, hc->pci_membase + A_FIFO_DATA0);
data++;
len--;
}
{
outb(A_FIFO_DATA0, (hc->pci_iobase)+4);
while (len>>2) {
- *(u32 *)data = inl(hc->pci_iobase);
+ *(u32 *)data = le32_to_cpu(inl(hc->pci_iobase));
data += 4;
len -= 4;
}
while (len>>1) {
- *(u16 *)data = inw(hc->pci_iobase);
+ *(u16 *)data = le16_to_cpu(inw(hc->pci_iobase));
data += 2;
len -= 2;
}
{
while (len>>2) {
*(u32 *)data =
- readl((hc->pci_membase)+A_FIFO_DATA0);
+ le32_to_cpu(readl(hc->pci_membase + A_FIFO_DATA0));
data += 4;
len -= 4;
}
while (len>>1) {
*(u16 *)data =
- readw((hc->pci_membase)+A_FIFO_DATA0);
+ le16_to_cpu(readw(hc->pci_membase + A_FIFO_DATA0));
data += 2;
len -= 2;
}
while (len) {
- *data = readb((hc->pci_membase)+A_FIFO_DATA0);
+ *data = readb(hc->pci_membase + A_FIFO_DATA0);
data++;
len--;
}
struct bchannel *bch;
int ch;
- if (!test_bit(rq->adr.channel, &dch->dev.channelmap[0]))
+ if (!test_channelmap(rq->adr.channel, dch->dev.channelmap))
return -EINVAL;
if (rq->protocol == ISDN_P_NONE)
return -EINVAL;
list_add(&bch->ch.list, &dch->dev.bchannels);
hc->chan[ch].bch = bch;
hc->chan[ch].port = 0;
- test_and_set_bit(bch->nr, &dch->dev.channelmap[0]);
+ set_channelmap(bch->nr, dch->dev.channelmap);
}
/* set optical line type */
if (port[Port_cnt] & 0x001) {
list_add(&bch->ch.list, &dch->dev.bchannels);
hc->chan[i + ch].bch = bch;
hc->chan[i + ch].port = pt;
- test_and_set_bit(bch->nr, &dch->dev.channelmap[0]);
+ set_channelmap(bch->nr, dch->dev.channelmap);
}
/* set master clock */
if (port[Port_cnt] & 0x001) {
static const struct hm_map hfcm_map[] = {
/*0*/ {VENDOR_BN, "HFC-1S Card (mini PCI)", 4, 1, 1, 3, 0, DIP_4S, 0},
-/*1*/ {VENDOR_BN, "HFC-2S Card", 4, 2, 1, 3, 0, DIP_4S},
+/*1*/ {VENDOR_BN, "HFC-2S Card", 4, 2, 1, 3, 0, DIP_4S, 0},
/*2*/ {VENDOR_BN, "HFC-2S Card (mini PCI)", 4, 2, 1, 3, 0, DIP_4S, 0},
/*3*/ {VENDOR_BN, "HFC-4S Card", 4, 4, 1, 2, 0, DIP_4S, 0},
/*4*/ {VENDOR_BN, "HFC-4S Card (mini PCI)", 4, 4, 1, 2, 0, 0, 0},
/*5*/ {VENDOR_CCD, "HFC-4S Eval (old)", 4, 4, 0, 0, 0, 0, 0},
-/*6*/ {VENDOR_CCD, "HFC-4S IOB4ST", 4, 4, 1, 2, 0, 0, 0},
+/*6*/ {VENDOR_CCD, "HFC-4S IOB4ST", 4, 4, 1, 2, 0, DIP_4S, 0},
/*7*/ {VENDOR_CCD, "HFC-4S", 4, 4, 1, 2, 0, 0, 0},
/*8*/ {VENDOR_DIG, "HFC-4S Card", 4, 4, 0, 2, 0, 0, HFC_IO_MODE_REGIO},
/*9*/ {VENDOR_CCD, "HFC-4S Swyx 4xS0 SX2 QuadBri", 4, 4, 1, 2, 0, 0, 0},
if (debug & DEBUG_HFCMULTI_INIT)
printk(KERN_DEBUG "%s: init entered\n", __func__);
-#ifdef __BIG_ENDIAN
-#error "not running on big endian machines now"
-#endif
hfc_interrupt = symbol_get(ztdummy_extern_interrupt);
register_interrupt = symbol_get(ztdummy_register_interrupt);
unregister_interrupt = symbol_get(ztdummy_unregister_interrupt);
card->dch.dev.nrbchan = 2;
for (i = 0; i < 2; i++) {
card->bch[i].nr = i + 1;
- test_and_set_bit(i + 1, &card->dch.dev.channelmap[0]);
+ set_channelmap(i + 1, card->dch.dev.channelmap);
card->bch[i].debug = debug;
mISDN_initbchannel(&card->bch[i], MAX_DATA_MEM);
card->bch[i].hw = card;
typedef struct PofTimeStamp_tag {
/*00 */ unsigned long UnixTime __attribute__((packed));
- /*04 */ unsigned char DateTimeText[0x28] __attribute__((packed));
+ /*04 */ unsigned char DateTimeText[0x28];
/* =40 */
/*2C */
} tPofTimeStamp;
struct bchannel *bch;
int ch;
- if (!test_bit(rq->adr.channel & 0x1f,
- &dch->dev.channelmap[rq->adr.channel >> 5]))
+ if (!test_channelmap(rq->adr.channel, dch->dev.channelmap))
return -EINVAL;
if (rq->protocol == ISDN_P_NONE)
return -EINVAL;
bch->ch.nr = i + ch;
list_add(&bch->ch.list, &dch->dev.bchannels);
hc->chan[i + ch].bch = bch;
- test_and_set_bit(bch->nr & 0x1f,
- &dch->dev.channelmap[bch->nr >> 5]);
+ set_channelmap(bch->nr, dch->dev.channelmap);
}
ret = mISDN_register_device(&dch->dev, hc->name);
if (ret)
di.Bprotocols = dev->Bprotocols | get_all_Bprotocols();
di.protocol = dev->D.protocol;
memcpy(di.channelmap, dev->channelmap,
- MISDN_CHMAP_SIZE * 4);
+ sizeof(di.channelmap));
di.nrbchan = dev->nrbchan;
strcpy(di.name, dev->name);
if (copy_to_user((void __user *)arg, &di, sizeof(di)))
di.Bprotocols = dev->Bprotocols | get_all_Bprotocols();
di.protocol = dev->D.protocol;
memcpy(di.channelmap, dev->channelmap,
- MISDN_CHMAP_SIZE * 4);
+ sizeof(di.channelmap));
di.nrbchan = dev->nrbchan;
strcpy(di.name, dev->name);
if (copy_to_user((void __user *)arg, &di, sizeof(di)))
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
-#include <asm/arch/board-ams-delta.h>
+#include <mach/board-ams-delta.h>
/*
* Our context
#include <linux/platform_device.h>
#include <linux/leds.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
#define GPIO_RED_LED (93)
#define GPIO_GREEN_LED (94)
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
-#include <asm/mach-types.h>
-#include <asm/arch/corgi.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/corgi.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
#include <asm/hardware/scoop.h>
static void corgiled_amber_set(struct led_classdev *led_cdev,
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
static short __iomem *latch_address;
#include <linux/string.h>
#include <linux/ctype.h>
#include <linux/leds.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/hardware.h>
-#include <asm/arch/h1940-latch.h>
+#include <mach/regs-gpio.h>
+#include <mach/hardware.h>
+#include <mach/h1940-latch.h>
/*
* Green led.
#include <linux/device.h>
#include <linux/leds.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/locomo.h>
static void locomoled_brightness_set(struct led_classdev *led_cdev,
#include <linux/platform_device.h>
#include <linux/leds.h>
-#include <asm/hardware.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/leds-gpio.h>
+#include <mach/hardware.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
/* our context */
#include <linux/leds.h>
#include <asm/hardware/scoop.h>
#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/spitz.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/spitz.h>
static void spitzled_amber_set(struct led_classdev *led_cdev,
enum led_brightness value)
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/timer.h>
-#include <linux/hdreg.h>
#include <linux/stddef.h>
#include <linux/init.h>
#include <linux/ide.h>
case 0:
bitmap_file_set_bit(bitmap, offset);
bitmap_count_page(bitmap,offset, 1);
- blk_plug_device(bitmap->mddev->queue);
+ blk_plug_device_unlocked(bitmap->mddev->queue);
/* fall through */
case 1:
*bmc = 2;
*/
static int lookup_device(const char *path, dev_t *dev)
{
- int r;
- struct nameidata nd;
- struct inode *inode;
-
- if ((r = path_lookup(path, LOOKUP_FOLLOW, &nd)))
- return r;
-
- inode = nd.path.dentry->d_inode;
- if (!inode) {
- r = -ENOENT;
- goto out;
- }
-
- if (!S_ISBLK(inode->i_mode)) {
- r = -ENOTBLK;
- goto out;
- }
-
- *dev = inode->i_rdev;
-
- out:
- path_put(&nd.path);
- return r;
+ struct block_device *bdev = lookup_bdev(path);
+ if (IS_ERR(bdev))
+ return PTR_ERR(bdev);
+ *dev = bdev->bd_dev;
+ bdput(bdev);
+ return 0;
}
/*
if (!atomic_read(&mddev->writes_pending)) {
mddev->safemode = 1;
if (mddev->external)
- sysfs_notify(&mddev->kobj, NULL, "array_state");
+ set_bit(MD_NOTIFY_ARRAY_STATE, &mddev->flags);
}
md_wakeup_thread(mddev->thread);
}
if (mddev->degraded) {
rdev_for_each(rdev, rtmp, mddev) {
if (rdev->raid_disk >= 0 &&
- !test_bit(In_sync, &rdev->flags))
+ !test_bit(In_sync, &rdev->flags) &&
+ !test_bit(Blocked, &rdev->flags))
spares++;
if (rdev->raid_disk < 0
&& !test_bit(Faulty, &rdev->flags)) {
if (mddev->bitmap)
bitmap_daemon_work(mddev->bitmap);
+ if (test_and_clear_bit(MD_NOTIFY_ARRAY_STATE, &mddev->flags))
+ sysfs_notify(&mddev->kobj, NULL, "array_state");
+
if (mddev->ro)
return;
conf->nr_queued ++;
spin_unlock_irqrestore(&conf->device_lock, flags);
+ /* wake up frozen array... */
+ wake_up(&conf->wait_barrier);
+
md_wakeup_thread(mddev->thread);
}
*
*/
-static void handle_stripe5(struct stripe_head *sh)
+static bool handle_stripe5(struct stripe_head *sh)
{
raid5_conf_t *conf = sh->raid_conf;
int disks = sh->disks, i;
if (sh->reconstruct_state == reconstruct_state_result) {
sh->reconstruct_state = reconstruct_state_idle;
clear_bit(STRIPE_EXPANDING, &sh->state);
- for (i = conf->raid_disks; i--; )
+ for (i = conf->raid_disks; i--; ) {
set_bit(R5_Wantwrite, &sh->dev[i].flags);
- set_bit(R5_LOCKED, &dev->flags);
+ set_bit(R5_LOCKED, &sh->dev[i].flags);
s.locked++;
+ }
}
if (s.expanded && test_bit(STRIPE_EXPANDING, &sh->state) &&
ops_run_io(sh, &s);
return_io(return_bi);
+
+ return blocked_rdev == NULL;
}
-static void handle_stripe6(struct stripe_head *sh, struct page *tmp_page)
+static bool handle_stripe6(struct stripe_head *sh, struct page *tmp_page)
{
raid6_conf_t *conf = sh->raid_conf;
int disks = sh->disks;
ops_run_io(sh, &s);
return_io(return_bi);
+
+ return blocked_rdev == NULL;
}
-static void handle_stripe(struct stripe_head *sh, struct page *tmp_page)
+/* returns true if the stripe was handled */
+static bool handle_stripe(struct stripe_head *sh, struct page *tmp_page)
{
if (sh->raid_conf->level == 6)
- handle_stripe6(sh, tmp_page);
+ return handle_stripe6(sh, tmp_page);
else
- handle_stripe5(sh);
+ return handle_stripe5(sh);
}
clear_bit(STRIPE_INSYNC, &sh->state);
spin_unlock(&sh->lock);
- handle_stripe(sh, NULL);
+ /* wait for any blocked device to be handled */
+ while(unlikely(!handle_stripe(sh, NULL)))
+ ;
release_stripe(sh);
return STRIPE_SECTORS;
sh = __get_priority_stripe(conf);
- if (!sh) {
- async_tx_issue_pending_all();
+ if (!sh)
break;
- }
spin_unlock_irq(&conf->device_lock);
handled++;
spin_unlock_irq(&conf->device_lock);
+ async_tx_issue_pending_all();
unplug_slaves(mddev);
pr_debug("--- raid5d inactive\n");
static int dvico_bluebird_xc2028_callback(void *ptr, int command, int arg)
{
- struct dvb_usb_device *d = ptr;
+ struct dvb_usb_adapter *adap = ptr;
+ struct dvb_usb_device *d = adap->dev;
switch (command) {
case XC2028_TUNER_RESET:
.callback = dvico_bluebird_xc2028_callback,
};
static struct xc2028_ctrl ctl = {
- .fname = "xc3028-dvico-au-01.fw",
+ .fname = "xc3028-v27.fw",
.max_len = 64,
- .scode_table = XC3028_FE_ZARLINK456,
+ .demod = XC3028_FE_ZARLINK456,
};
fe = dvb_attach(xc2028_attach, adap->fe, &cfg);
config DVB_DRX397XD
tristate "Micronas DRX3975D/DRX3977D based"
- depends on DVB_CORE && I2C && HOTPLUG
+ depends on DVB_CORE && I2C
default m if DVB_FE_CUSTOMISE
- select FW_LOADER
help
A DVB-T tuner module. Say Y when you want to support this frontend.
depends on VIDEO_ZORAN
help
Say Y to support Zoran boards based on 36060 chips.
- This includes Iomega Bus, Pinnacle DC10, Linux media Labs 33
+ This includes Iomega Buz, Pinnacle DC10, Linux media Labs 33
and 33 R10 and AverMedia 6 boards.
config VIDEO_ZORAN_BUZ
#include <linux/sched.h>
#include <linux/videodev.h>
#include <media/v4l2-common.h>
+#include <media/v4l2-ioctl.h>
#include <linux/mutex.h>
#include <asm/uaccess.h>
static struct video_device ar_template = {
.name = "Colour AR VGA",
- .type = VID_TYPE_CAPTURE,
.fops = &ar_fops,
.release = ar_release,
.minor = -1,
module_param(debug, bool, 0644);
-MODULE_PARM_DESC(debug, "Debugging messages\n\t\t\t0=Off (default), 1=On");
+MODULE_PARM_DESC(debug, "Debugging messages, 0=Off (default), 1=On");
/* ----------------------------------------------------------------------- */
module_param(debug, bool, 0644);
-MODULE_PARM_DESC(debug, "Debugging messages\n\t\t\t0=Off (default), 1=On");
+MODULE_PARM_DESC(debug, "Debugging messages, 0=Off (default), 1=On");
static unsigned short normal_i2c[] = { 0x22 >> 1, I2C_CLIENT_END };
.valid = EM28XX_BOARD_NOT_VALIDATED,
.vchannels = 3,
.tuner_type = TUNER_XC2028,
+ .mts_firmware = 1,
.decoder = EM28XX_TVP5150,
.input = { {
.type = EM28XX_VMUX_TELEVISION,
{
struct usb_device *dev = gspca_dev->dev;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (len > sizeof gspca_dev->usb_buf) {
err("reg_r: buffer overflow");
return;
{
struct usb_device *dev = gspca_dev->dev;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (len > sizeof gspca_dev->usb_buf) {
err("reg_w: buffer overflow");
return;
{
struct usb_device *dev = gspca_dev->dev;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (len > sizeof gspca_dev->usb_buf) {
err("reg_r: buffer overflow");
return;
{
struct usb_device *dev = gspca_dev->dev;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (len > sizeof gspca_dev->usb_buf) {
err("reg_w: buffer overflow");
return;
reg_w_val(gspca_dev, 0x80, 0x20); /* 0x20; */
}
+static void setbrightness(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+ int i;
+ __u8 brightness = sd->brightness;
+
+ for (i = 0; i < 4; i++)
+ reg_w_val(gspca_dev, ET_O_RED + i, brightness);
+}
+
+static void getbrightness(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+ int i;
+ int brightness = 0;
+
+ for (i = 0; i < 4; i++) {
+ reg_r(gspca_dev, ET_O_RED + i, 1);
+ brightness += gspca_dev->usb_buf[0];
+ }
+ sd->brightness = brightness >> 3;
+}
+
+static void setcontrast(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+ __u8 RGBG[] = { 0x80, 0x80, 0x80, 0x80, 0x00, 0x00 };
+ __u8 contrast = sd->contrast;
+
+ memset(RGBG, contrast, sizeof(RGBG) - 2);
+ reg_w(gspca_dev, ET_G_RED, RGBG, 6);
+}
+
+static void getcontrast(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+ int i;
+ int contrast = 0;
+
+ for (i = 0; i < 4; i++) {
+ reg_r(gspca_dev, ET_G_RED + i, 1);
+ contrast += gspca_dev->usb_buf[0];
+ }
+ sd->contrast = contrast >> 2;
+}
+
static void setcolors(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
}
}
+static void setautogain(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ if (sd->autogain)
+ sd->ag_cnt = AG_CNT_START;
+ else
+ sd->ag_cnt = -1;
+}
+
static void Et_init1(struct gspca_dev *gspca_dev)
{
__u8 value;
sd->contrast = CONTRAST_DEF;
sd->colors = COLOR_DEF;
sd->autogain = AUTOGAIN_DEF;
+ sd->ag_cnt = -1;
return 0;
}
else
Et_init2(gspca_dev);
+ setautogain(gspca_dev);
+
reg_w_val(gspca_dev, ET_RESET_ALL, 0x08);
et_video(gspca_dev, 1); /* video on */
}
{
}
-static void setbrightness(struct gspca_dev *gspca_dev)
-{
- struct sd *sd = (struct sd *) gspca_dev;
- int i;
- __u8 brightness = sd->brightness;
-
- for (i = 0; i < 4; i++)
- reg_w_val(gspca_dev, ET_O_RED + i, brightness);
-}
-
-static void getbrightness(struct gspca_dev *gspca_dev)
-{
- struct sd *sd = (struct sd *) gspca_dev;
- int i;
- int brightness = 0;
-
- for (i = 0; i < 4; i++) {
- reg_r(gspca_dev, ET_O_RED + i, 1);
- brightness += gspca_dev->usb_buf[0];
- }
- sd->brightness = brightness >> 3;
-}
-
-static void setcontrast(struct gspca_dev *gspca_dev)
-{
- struct sd *sd = (struct sd *) gspca_dev;
- __u8 RGBG[] = { 0x80, 0x80, 0x80, 0x80, 0x00, 0x00 };
- __u8 contrast = sd->contrast;
-
- memset(RGBG, contrast, sizeof(RGBG) - 2);
- reg_w(gspca_dev, ET_G_RED, RGBG, 6);
-}
-
-static void getcontrast(struct gspca_dev *gspca_dev)
-{
- struct sd *sd = (struct sd *) gspca_dev;
- int i;
- int contrast = 0;
-
- for (i = 0; i < 4; i++) {
- reg_r(gspca_dev, ET_G_RED + i, 1);
- contrast += gspca_dev->usb_buf[0];
- }
- sd->contrast = contrast >> 2;
-}
-
static __u8 Et_getgainG(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
#define LIMIT(color) \
(unsigned char)((color > 0xff)?0xff:((color < 0)?0:color))
-static void setautogain(struct gspca_dev *gspca_dev)
+static void do_autogain(struct gspca_dev *gspca_dev)
{
- __u8 luma = 0;
+ struct sd *sd = (struct sd *) gspca_dev;
+ __u8 luma;
__u8 luma_mean = 128;
__u8 luma_delta = 20;
__u8 spring = 4;
- int Gbright = 0;
+ int Gbright;
__u8 r, g, b;
+ if (sd->ag_cnt < 0)
+ return;
+ if (--sd->ag_cnt >= 0)
+ return;
+ sd->ag_cnt = AG_CNT_START;
+
Gbright = Et_getgainG(gspca_dev);
reg_r(gspca_dev, ET_LUMA_CENTER, 4);
g = (gspca_dev->usb_buf[0] + gspca_dev->usb_buf[3]) >> 1;
__u8 *data, /* isoc packet */
int len) /* iso packet length */
{
- struct sd *sd;
int seqframe;
seqframe = data[0] & 0x3f;
frame = gspca_frame_add(gspca_dev, LAST_PACKET, frame,
data, 0);
gspca_frame_add(gspca_dev, FIRST_PACKET, frame, data, len);
- sd = (struct sd *) gspca_dev;
- if (sd->ag_cnt >= 0) {
- if (--sd->ag_cnt < 0) {
- sd->ag_cnt = AG_CNT_START;
- setautogain(gspca_dev);
- }
- }
return;
}
if (len) {
struct sd *sd = (struct sd *) gspca_dev;
sd->autogain = val;
- if (val)
- sd->ag_cnt = AG_CNT_START;
- else
- sd->ag_cnt = -1;
+ if (gspca_dev->streaming)
+ setautogain(gspca_dev);
return 0;
}
.stop0 = sd_stop0,
.close = sd_close,
.pkt_scan = sd_pkt_scan,
+ .dq_callback = do_autogain,
};
/* -- module initialisation -- */
static int video_nr = -1;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
int gspca_debug = D_ERR | D_PROBE;
EXPORT_SYMBOL(gspca_debug);
w = fmt->fmt.pix.width;
h = fmt->fmt.pix.height;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (gspca_debug & D_CONF)
PDEBUG_MODE("try fmt cap", fmt->fmt.pix.pixelformat, w, h);
#endif
}
gspca_dev->users++;
file->private_data = gspca_dev;
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
/* activate the v4l2 debug */
if (gspca_debug & D_V4L2)
gspca_dev->vdev.debug |= 3;
if (ctrl->id != ctrls->qctrl.id)
continue;
if (ctrl->value < ctrls->qctrl.minimum
- && ctrl->value > ctrls->qctrl.maximum)
+ || ctrl->value > ctrls->qctrl.maximum)
return -ERANGE;
PDEBUG(D_CONF, "set ctrl [%08x] = %d", ctrl->id, ctrl->value);
if (mutex_lock_interruptible(&gspca_dev->usb_lock))
if (ret < 0)
goto out;
}
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (gspca_debug & D_STREAM) {
PDEBUG_MODE("stream on OK",
gspca_dev->pixfmt,
module_init(gspca_init);
module_exit(gspca_exit);
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
module_param_named(debug, gspca_debug, int, 0644);
MODULE_PARM_DESC(debug,
"Debug (bit) 0x01:error 0x02:probe 0x04:config"
#include <media/v4l2-common.h>
#include <linux/mutex.h>
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+/* compilation option */
+#define GSPCA_DEBUG 1
+
+#ifdef GSPCA_DEBUG
/* GSPCA our debug messages */
extern int gspca_debug;
#define PDEBUG(level, fmt, args...) \
struct gspca_dev gspca_dev; /* !! must be the first item */
/* Determined by sensor type */
- short maxwidth;
- short maxheight;
+ char sif;
unsigned char primary_i2c_slave; /* I2C write id of sensor */
unsigned char brightness;
unsigned char contrast;
unsigned char colors;
+ __u8 hflip;
+ __u8 vflip;
char compress; /* Should the next frame be compressed? */
char compress_inited; /* Are compression params uploaded? */
static int sd_getcontrast(struct gspca_dev *gspca_dev, __s32 *val);
static int sd_setcolors(struct gspca_dev *gspca_dev, __s32 val);
static int sd_getcolors(struct gspca_dev *gspca_dev, __s32 *val);
+static int sd_sethflip(struct gspca_dev *gspca_dev, __s32 val);
+static int sd_gethflip(struct gspca_dev *gspca_dev, __s32 *val);
+static int sd_setvflip(struct gspca_dev *gspca_dev, __s32 val);
+static int sd_getvflip(struct gspca_dev *gspca_dev, __s32 *val);
static struct ctrl sd_ctrls[] = {
-#define SD_BRIGHTNESS 0
{
{
.id = V4L2_CID_BRIGHTNESS,
.minimum = 0,
.maximum = 255,
.step = 1,
- .default_value = 127,
+#define BRIGHTNESS_DEF 127
+ .default_value = BRIGHTNESS_DEF,
},
.set = sd_setbrightness,
.get = sd_getbrightness,
},
-#define SD_CONTRAST 1
{
{
.id = V4L2_CID_CONTRAST,
.minimum = 0,
.maximum = 255,
.step = 1,
- .default_value = 127,
+#define CONTRAST_DEF 127
+ .default_value = CONTRAST_DEF,
},
.set = sd_setcontrast,
.get = sd_getcontrast,
},
-#define SD_COLOR 2
{
{
.id = V4L2_CID_SATURATION,
.type = V4L2_CTRL_TYPE_INTEGER,
- .name = "Saturation",
+ .name = "Color",
.minimum = 0,
.maximum = 255,
.step = 1,
- .default_value = 127,
+#define COLOR_DEF 127
+ .default_value = COLOR_DEF,
},
.set = sd_setcolors,
.get = sd_getcolors,
},
+/* next controls work with ov7670 only */
+ {
+ {
+ .id = V4L2_CID_HFLIP,
+ .type = V4L2_CTRL_TYPE_BOOLEAN,
+ .name = "Mirror",
+ .minimum = 0,
+ .maximum = 1,
+ .step = 1,
+#define HFLIP_DEF 0
+ .default_value = HFLIP_DEF,
+ },
+ .set = sd_sethflip,
+ .get = sd_gethflip,
+ },
+ {
+ {
+ .id = V4L2_CID_VFLIP,
+ .type = V4L2_CTRL_TYPE_BOOLEAN,
+ .name = "Vflip",
+ .minimum = 0,
+ .maximum = 1,
+ .step = 1,
+#define VFLIP_DEF 0
+ .default_value = VFLIP_DEF,
+ },
+ .set = sd_setvflip,
+ .get = sd_getvflip,
+ },
};
static struct v4l2_pix_format vga_mode[] = {
{320, 240, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE,
.bytesperline = 320,
- .sizeimage = 320 * 240 * 3 / 8 + 589,
+ .sizeimage = 320 * 240 * 3 / 8 + 590,
.colorspace = V4L2_COLORSPACE_JPEG,
.priv = 1},
{640, 480, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE,
static struct v4l2_pix_format sif_mode[] = {
{176, 144, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE,
.bytesperline = 176,
- .sizeimage = 176 * 144 * 3 / 8 + 589,
+ .sizeimage = 176 * 144 * 3 / 8 + 590,
.colorspace = V4L2_COLORSPACE_JPEG,
.priv = 1},
{352, 288, V4L2_PIX_FMT_JPEG, V4L2_FIELD_NONE,
.bytesperline = 352,
- .sizeimage = 352 * 288 * 3 / 8 + 589,
+ .sizeimage = 352 * 288 * 3 / 8 + 590,
.colorspace = V4L2_COLORSPACE_JPEG,
.priv = 0},
};
#define OV7670_REG_VSTART 0x19 /* Vert start high bits */
#define OV7670_REG_VSTOP 0x1a /* Vert stop high bits */
#define OV7670_REG_MVFP 0x1e /* Mirror / vflip */
+#define OV7670_MVFP_VFLIP 0x10 /* vertical flip */
#define OV7670_MVFP_MIRROR 0x20 /* Mirror image */
#define OV7670_REG_AEW 0x24 /* AGC upper limit */
#define OV7670_REG_AEB 0x25 /* AGC lower limit */
#define OV7670_REG_HAECC7 0xaa /* Hist AEC/AGC control 7 */
#define OV7670_REG_BD60MAX 0xab /* 60hz banding step limit */
-struct ovsensor_window {
- short x;
- short y;
- short width;
- short height;
-/* int format; */
- short quarter; /* Scale width and height down 2x */
- short clockdiv; /* Clock divisor setting */
-};
-
static unsigned char ov7670_abs_to_sm(unsigned char v)
{
if (v > 127)
return 0;
}
-/* Switch on standard JPEG compression. Returns 0 for success. */
-static int ov519_init_compression(struct sd *sd)
-{
- if (!sd->compress_inited) {
- if (reg_w_mask(sd, OV519_SYS_EN_CLK1, 1 << 2, 1 << 2) < 0) {
- PDEBUG(D_ERR, "Error switching to compressed mode");
- return -EIO;
- }
- sd->compress_inited = 1;
- }
- return 0;
-}
-
/* Set the read and write slave IDs. The "slave" argument is the write slave,
* and the read slave will be set to (slave + 1).
* This should not be called from outside the i2c I/O functions.
return -1;
}
if ((rc & 3) == 1) {
- PDEBUG(D_PROBE, "Sensor is an OV8610");
sd->sensor = SEN_OV8610;
} else {
PDEBUG(D_ERR, "Unknown image sensor version: %d", rc & 3);
return -1;
}
PDEBUG(D_PROBE, "Writing 8610 registers");
- if (write_i2c_regvals(sd,
- norm_8610,
- sizeof norm_8610 / sizeof norm_8610[0]))
+ if (write_i2c_regvals(sd, norm_8610, ARRAY_SIZE(norm_8610)))
return -1;
/* Set sensor-specific vars */
- sd->maxwidth = 640;
- sd->maxheight = 480;
+/* sd->sif = 0; already done */
return 0;
}
{ OV7670_REG_COM7, OV7670_COM7_RESET },
{ OV7670_REG_TSLB, 0x04 }, /* OV */
{ OV7670_REG_COM7, OV7670_COM7_FMT_VGA }, /* VGA */
- { OV7670_REG_CLKRC, 0x1 },
+ { OV7670_REG_CLKRC, 0x01 },
/*
* Set the hardware window. These values from OV don't entirely
* make sense - hstop is less than hstart. But they work...
{ 0x70, 0x3a }, { 0x71, 0x35 },
{ 0x72, 0x11 }, { 0x73, 0xf0 },
{ 0xa2, 0x02 },
-/* jfm */
-/* { OV7670_REG_COM10, 0x0 }, */
+/* { OV7670_REG_COM10, 0x0 }, */
/* Gamma curve values */
{ 0x7a, 0x20 },
-/* jfm:win 7b=1c */
{ 0x7b, 0x10 },
-/* jfm:win 7c=28 */
{ 0x7c, 0x1e },
-/* jfm:win 7d=3c */
{ 0x7d, 0x35 },
{ 0x7e, 0x5a }, { 0x7f, 0x69 },
{ 0x80, 0x76 }, { 0x81, 0x80 },
| OV7670_COM8_BFILT },
{ OV7670_REG_GAIN, 0 }, { OV7670_REG_AECH, 0 },
{ OV7670_REG_COM4, 0x40 }, /* magic reserved bit */
-/* jfm:win 14=38 */
{ OV7670_REG_COM9, 0x18 }, /* 4x gain + magic rsvd bit */
{ OV7670_REG_BD50MAX, 0x05 }, { OV7670_REG_BD60MAX, 0x07 },
{ OV7670_REG_AEW, 0x95 }, { OV7670_REG_AEB, 0x33 },
{ OV7670_REG_VPT, 0xe3 }, { OV7670_REG_HAECC1, 0x78 },
{ OV7670_REG_HAECC2, 0x68 },
-/* jfm:win a1=0b */
{ 0xa1, 0x03 }, /* magic */
{ OV7670_REG_HAECC3, 0xd8 }, { OV7670_REG_HAECC4, 0xd8 },
{ OV7670_REG_HAECC5, 0xf0 }, { OV7670_REG_HAECC6, 0x90 },
/* Almost all of these are magic "reserved" values. */
{ OV7670_REG_COM5, 0x61 }, { OV7670_REG_COM6, 0x4b },
{ 0x16, 0x02 },
-/* jfm */
-/* { OV7670_REG_MVFP, 0x07|OV7670_MVFP_MIRROR }, */
{ OV7670_REG_MVFP, 0x07 },
{ 0x21, 0x02 }, { 0x22, 0x91 },
{ 0x29, 0x07 }, { 0x33, 0x0b },
{ OV7670_REG_EDGE, 0 },
{ 0x75, 0x05 }, { 0x76, 0xe1 },
{ 0x4c, 0 }, { 0x77, 0x01 },
- { OV7670_REG_COM13, 0xc3 }, { 0x4b, 0x09 },
+ { OV7670_REG_COM13, OV7670_COM13_GAMMA
+ | OV7670_COM13_UVSAT
+ | 2}, /* was 3 */
+ { 0x4b, 0x09 },
{ 0xc9, 0x60 }, { OV7670_REG_COM16, 0x38 },
{ 0x56, 0x40 },
{ 0x79, 0x03 }, { 0xc8, 0x40 },
{ 0x79, 0x05 }, { 0xc8, 0x30 },
{ 0x79, 0x26 },
-
- /* Format YUV422 */
- { OV7670_REG_COM7, OV7670_COM7_YUV }, /* Selects YUV mode */
- { OV7670_REG_RGB444, 0 }, /* No RGB444 please */
- { OV7670_REG_COM1, 0 },
- { OV7670_REG_COM15, OV7670_COM15_R00FF },
- { OV7670_REG_COM9, 0x18 },
- /* 4x gain ceiling; 0x8 is reserved bit */
- { 0x4f, 0x80 }, /* "matrix coefficient 1" */
- { 0x50, 0x80 }, /* "matrix coefficient 2" */
- { 0x52, 0x22 }, /* "matrix coefficient 4" */
- { 0x53, 0x5e }, /* "matrix coefficient 5" */
- { 0x54, 0x80 }, /* "matrix coefficient 6" */
- { OV7670_REG_COM13, OV7670_COM13_GAMMA|OV7670_COM13_UVSAT },
-};
+ };
PDEBUG(D_PROBE, "starting OV7xx0 configuration");
-/* jfm:already done? */
- if (init_ov_sensor(sd) < 0)
- PDEBUG(D_ERR, "Failed to read sensor ID");
- else
- PDEBUG(D_PROBE, "OV7xx0 initialized");
-
/* Detect sensor (sub)type */
rc = i2c_r(sd, OV7610_REG_COM_I);
return low;
}
if (high == 0x76) {
- if (low == 0x30) {
+ switch (low) {
+ case 0x30:
PDEBUG(D_PROBE, "Sensor is an OV7630/OV7635");
sd->sensor = SEN_OV7630;
- } else if (low == 0x40) {
+ break;
+ case 0x40:
PDEBUG(D_PROBE, "Sensor is an OV7645");
sd->sensor = SEN_OV7640; /* FIXME */
- } else if (low == 0x45) {
+ break;
+ case 0x45:
PDEBUG(D_PROBE, "Sensor is an OV7645B");
sd->sensor = SEN_OV7640; /* FIXME */
- } else if (low == 0x48) {
+ break;
+ case 0x48:
PDEBUG(D_PROBE, "Sensor is an OV7648");
sd->sensor = SEN_OV7640; /* FIXME */
- } else {
- PDEBUG(D_PROBE, "Unknown sensor: 0x76%X", low);
+ break;
+ default:
+ PDEBUG(D_PROBE, "Unknown sensor: 0x76%x", low);
return -1;
}
} else {
return -1;
}
- if (sd->sensor == SEN_OV7620) {
+ switch (sd->sensor) {
+ case SEN_OV7620:
PDEBUG(D_PROBE, "Writing 7620 registers");
- if (write_i2c_regvals(sd, norm_7620,
- sizeof norm_7620 / sizeof norm_7620[0]))
+ if (write_i2c_regvals(sd, norm_7620, ARRAY_SIZE(norm_7620)))
return -1;
- } else if (sd->sensor == SEN_OV7630) {
+ break;
+ case SEN_OV7630:
PDEBUG(D_ERR, "7630 is not supported by this driver version");
return -1;
- } else if (sd->sensor == SEN_OV7640) {
+ case SEN_OV7640:
PDEBUG(D_PROBE, "Writing 7640 registers");
- if (write_i2c_regvals(sd, norm_7640,
- sizeof norm_7640 / sizeof norm_7640[0]))
+ if (write_i2c_regvals(sd, norm_7640, ARRAY_SIZE(norm_7640)))
return -1;
- } else if (sd->sensor == SEN_OV7670) {
+ break;
+ case SEN_OV7670:
PDEBUG(D_PROBE, "Writing 7670 registers");
- if (write_i2c_regvals(sd, norm_7670,
- sizeof norm_7670 / sizeof norm_7670[0]))
+ if (write_i2c_regvals(sd, norm_7670, ARRAY_SIZE(norm_7670)))
return -1;
- } else {
+ break;
+ default:
PDEBUG(D_PROBE, "Writing 7610 registers");
- if (write_i2c_regvals(sd, norm_7610,
- sizeof norm_7610 / sizeof norm_7610[0]))
+ if (write_i2c_regvals(sd, norm_7610, ARRAY_SIZE(norm_7610)))
return -1;
+ break;
}
/* Set sensor-specific vars */
- sd->maxwidth = 640;
- sd->maxheight = 480;
+/* sd->sif = 0; already done */
return 0;
}
/* Ugh. The first two bits are the version bits, but
* the entire register value must be used. I guess OVT
* underestimated how many variants they would make. */
- if (rc == 0x00) {
+ switch (rc) {
+ case 0x00:
sd->sensor = SEN_OV6630;
PDEBUG(D_ERR,
"WARNING: Sensor is an OV66308. Your camera may have");
PDEBUG(D_ERR, "been misdetected in previous driver versions.");
- } else if (rc == 0x01) {
+ break;
+ case 0x01:
sd->sensor = SEN_OV6620;
- PDEBUG(D_PROBE, "Sensor is an OV6620");
- } else if (rc == 0x02) {
+ break;
+ case 0x02:
sd->sensor = SEN_OV6630;
PDEBUG(D_PROBE, "Sensor is an OV66308AE");
- } else if (rc == 0x03) {
+ break;
+ case 0x03:
sd->sensor = SEN_OV6630;
PDEBUG(D_PROBE, "Sensor is an OV66308AF");
- } else if (rc == 0x90) {
+ break;
+ case 0x90:
sd->sensor = SEN_OV6630;
PDEBUG(D_ERR,
"WARNING: Sensor is an OV66307. Your camera may have");
PDEBUG(D_ERR, "been misdetected in previous driver versions.");
- } else {
+ break;
+ default:
PDEBUG(D_ERR, "FATAL: Unknown sensor version: 0x%02x", rc);
return -1;
}
/* Set sensor-specific vars */
- sd->maxwidth = 352;
- sd->maxheight = 288;
+ sd->sif = 1;
if (sd->sensor == SEN_OV6620) {
PDEBUG(D_PROBE, "Writing 6x20 registers");
- if (write_i2c_regvals(sd, norm_6x20,
- sizeof norm_6x20 / sizeof norm_6x20[0]))
+ if (write_i2c_regvals(sd, norm_6x20, ARRAY_SIZE(norm_6x20)))
return -1;
} else {
PDEBUG(D_PROBE, "Writing 6x30 registers");
- if (write_i2c_regvals(sd, norm_6x30,
- sizeof norm_6x30 / sizeof norm_6x30[0]))
+ if (write_i2c_regvals(sd, norm_6x30, ARRAY_SIZE(norm_6x30)))
return -1;
}
return 0;
/* Turns on or off the LED. Only has an effect with OV511+/OV518(+)/OV519 */
static void ov51x_led_control(struct sd *sd, int on)
{
- PDEBUG(D_STREAM, "LED (%s)", on ? "on" : "off");
-
-/* if (sd->bridge == BRG_OV511PLUS) */
-/* reg_w(sd, R511_SYS_LED_CTL, on ? 1 : 0); */
-/* else if (sd->bridge == BRG_OV519) */
- reg_w_mask(sd, OV519_GPIO_DATA_OUT0, !on, 1); /* 0 / 1 */
-/* else if (sd->bclass == BCL_OV518) */
-/* reg_w_mask(sd, R518_GPIO_OUT, on ? 0x02 : 0x00, 0x02); */
+/* PDEBUG(D_STREAM, "LED (%s)", on ? "on" : "off"); */
+ reg_w_mask(sd, OV519_GPIO_DATA_OUT0, !on, 1); /* 0 / 1 */
}
/* this function is called at probe time */
struct sd *sd = (struct sd *) gspca_dev;
struct cam *cam;
-/* (from ov519_configure) */
static const struct ov_regvals init_519[] = {
{ 0x5a, 0x6d }, /* EnableSystem */
-/* jfm trace usbsnoop3-1.txt */
-/* jfm 53 = fb */
{ 0x53, 0x9b },
{ 0x54, 0xff }, /* set bit2 to enable jpeg */
{ 0x5d, 0x03 },
if (write_regvals(sd, init_519, ARRAY_SIZE(init_519)))
goto error;
-/* jfm: not seen in windows trace */
- if (ov519_init_compression(sd))
- goto error;
ov51x_led_control(sd, 0); /* turn LED off */
/* Test for 76xx */
cam = &gspca_dev->cam;
cam->epaddr = OV511_ENDPOINT_ADDRESS;
- if (sd->maxwidth == 640) {
+ if (!sd->sif) {
cam->cam_mode = vga_mode;
- cam->nmodes = sizeof vga_mode / sizeof vga_mode[0];
+ cam->nmodes = ARRAY_SIZE(vga_mode);
} else {
cam->cam_mode = sif_mode;
- cam->nmodes = sizeof sif_mode / sizeof sif_mode[0];
+ cam->nmodes = ARRAY_SIZE(sif_mode);
}
- sd->brightness = sd_ctrls[SD_BRIGHTNESS].qctrl.default_value;
- sd->contrast = sd_ctrls[SD_CONTRAST].qctrl.default_value;
- sd->colors = sd_ctrls[SD_COLOR].qctrl.default_value;
+ sd->brightness = BRIGHTNESS_DEF;
+ sd->contrast = CONTRAST_DEF;
+ sd->colors = COLOR_DEF;
+ sd->hflip = HFLIP_DEF;
+ sd->vflip = VFLIP_DEF;
return 0;
error:
PDEBUG(D_ERR, "OV519 Config failed");
*
* Do not put any sensor-specific code in here (including I2C I/O functions)
*/
-static int ov519_mode_init_regs(struct sd *sd,
- int width, int height)
+static int ov519_mode_init_regs(struct sd *sd)
{
static const struct ov_regvals mode_init_519_ov7670[] = {
{ 0x5d, 0x03 }, /* Turn off suspend mode */
/* windows reads 0x55 at this point, why? */
};
-/* int hi_res; */
-
- PDEBUG(D_CONF, "mode init %dx%d", width, height);
-
-/* if (width >= 800 && height >= 600)
- hi_res = 1;
- else
- hi_res = 0; */
-
-/* if (ov51x_stop(sd) < 0)
- return -EIO; */
-
/******** Set the mode ********/
if (sd->sensor != SEN_OV7670) {
if (write_regvals(sd, mode_init_519,
ARRAY_SIZE(mode_init_519)))
return -EIO;
+ if (sd->sensor == SEN_OV7640) {
+ /* Select 8-bit input mode */
+ reg_w_mask(sd, OV519_CAM_DFR, 0x10, 0x10);
+ }
} else {
if (write_regvals(sd, mode_init_519_ov7670,
ARRAY_SIZE(mode_init_519_ov7670)))
return -EIO;
}
- if (sd->sensor == SEN_OV7640) {
- /* Select 8-bit input mode */
- reg_w_mask(sd, OV519_CAM_DFR, 0x10, 0x10);
- }
-
- reg_w(sd, OV519_CAM_H_SIZE, width >> 4);
- reg_w(sd, OV519_CAM_V_SIZE, height >> 3);
+ reg_w(sd, OV519_CAM_H_SIZE, sd->gspca_dev.width >> 4);
+ reg_w(sd, OV519_CAM_V_SIZE, sd->gspca_dev.height >> 3);
reg_w(sd, OV519_CAM_X_OFFSETL, 0x00);
reg_w(sd, OV519_CAM_X_OFFSETH, 0x00);
reg_w(sd, OV519_CAM_Y_OFFSETL, 0x00);
/* FIXME: These are only valid at the max resolution. */
sd->clockdiv = 0;
- if (sd->sensor == SEN_OV7640) {
+ switch (sd->sensor) {
+ case SEN_OV7640:
switch (sd->frame_rate) {
-/*jfm: default was 30 fps */
+/*fixme: default was 30 fps */
case 30:
reg_w(sd, 0xa4, 0x0c);
reg_w(sd, 0x23, 0xff);
sd->clockdiv = 1;
break;
}
- } else if (sd->sensor == SEN_OV8610) {
+ break;
+ case SEN_OV8610:
switch (sd->frame_rate) {
default: /* 15 fps */
/* case 15: */
reg_w(sd, 0x23, 0x1b);
break;
}
- sd->clockdiv = 0;
- } else if (sd->sensor == SEN_OV7670) { /* guesses, based on 7640 */
+ break;
+ case SEN_OV7670: /* guesses, based on 7640 */
PDEBUG(D_STREAM, "Setting framerate to %d fps",
(sd->frame_rate == 0) ? 15 : sd->frame_rate);
+ reg_w(sd, 0xa4, 0x10);
switch (sd->frame_rate) {
case 30:
- reg_w(sd, 0xa4, 0x10);
reg_w(sd, 0x23, 0xff);
break;
case 20:
- reg_w(sd, 0xa4, 0x10);
reg_w(sd, 0x23, 0x1b);
break;
- default: /* 15 fps */
-/* case 15: */
- reg_w(sd, 0xa4, 0x10);
+ default:
+/* case 15: */
reg_w(sd, 0x23, 0xff);
sd->clockdiv = 1;
break;
}
+ break;
}
-/* if (ov51x_restart(sd) < 0)
- return -EIO; */
-
- /* Reset it just for good measure */
-/* if (ov51x_reset(sd, OV511_RESET_NOREGS) < 0)
- return -EIO; */
return 0;
}
-static int mode_init_ov_sensor_regs(struct sd *sd,
- struct ovsensor_window *win)
+static int mode_init_ov_sensor_regs(struct sd *sd)
{
- int qvga = win->quarter;
+ struct gspca_dev *gspca_dev;
+ int qvga;
+
+ gspca_dev = &sd->gspca_dev;
+ qvga = gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv;
/******** Mode (VGA/QVGA) and sensor specific regs ********/
switch (sd->sensor) {
OV7670_COM7_FMT_MASK);
break;
case SEN_OV6620:
- i2c_w_mask(sd, 0x14, qvga ? 0x20 : 0x00, 0x20);
- break;
case SEN_OV6630:
i2c_w_mask(sd, 0x14, qvga ? 0x20 : 0x00, 0x20);
break;
}
/******** Palette-specific regs ********/
-/* Need to do work here for the OV7670 */
-
- if (sd->sensor == SEN_OV7610 || sd->sensor == SEN_OV76BE) {
- /* not valid on the OV6620/OV7620/6630? */
- i2c_w_mask(sd, 0x0e, 0x00, 0x40);
- }
+ if (sd->sensor == SEN_OV7610 || sd->sensor == SEN_OV76BE) {
+ /* not valid on the OV6620/OV7620/6630? */
+ i2c_w_mask(sd, 0x0e, 0x00, 0x40);
+ }
- /* The OV518 needs special treatment. Although both the OV518
- * and the OV6630 support a 16-bit video bus, only the 8 bit Y
- * bus is actually used. The UV bus is tied to ground.
- * Therefore, the OV6630 needs to be in 8-bit multiplexed
- * output mode */
+ /* The OV518 needs special treatment. Although both the OV518
+ * and the OV6630 support a 16-bit video bus, only the 8 bit Y
+ * bus is actually used. The UV bus is tied to ground.
+ * Therefore, the OV6630 needs to be in 8-bit multiplexed
+ * output mode */
- /* OV7640 is 8-bit only */
+ /* OV7640 is 8-bit only */
- if (sd->sensor != SEN_OV6630 && sd->sensor != SEN_OV7640)
- i2c_w_mask(sd, 0x13, 0x00, 0x20);
-/* } */
+ if (sd->sensor != SEN_OV6630 && sd->sensor != SEN_OV7640)
+ i2c_w_mask(sd, 0x13, 0x00, 0x20);
/******** Clock programming ********/
/* The OV6620 needs special handling. This prevents the
/* Clock down */
i2c_w(sd, 0x2a, 0x04);
- i2c_w(sd, 0x11, win->clockdiv);
+ i2c_w(sd, 0x11, sd->clockdiv);
i2c_w(sd, 0x2a, 0x84);
/* This next setting is critical. It seems to improve
* the gain or the contrast. The "reserved" bits seem
* to have some effect in this case. */
i2c_w(sd, 0x2d, 0x85);
- } else if (win->clockdiv >= 0) {
- i2c_w(sd, 0x11, win->clockdiv);
+ } else if (sd->clockdiv >= 0) {
+ i2c_w(sd, 0x11, sd->clockdiv);
}
/******** Special Features ********/
/* is fully tested. */
/* 7620/6620/6630? don't have register 0x35, so play it safe */
if (sd->sensor == SEN_OV7610 || sd->sensor == SEN_OV76BE) {
- if (win->width == 640 /*&& win->height == 480*/)
+ if (!qvga)
i2c_w(sd, 0x35, 0x9e);
else
i2c_w(sd, 0x35, 0x1e);
return 0;
}
-static int set_ov_sensor_window(struct sd *sd,
- struct ovsensor_window *win)
+static void sethvflip(struct sd *sd)
{
+ if (sd->sensor != SEN_OV7670)
+ return;
+ if (sd->gspca_dev.streaming)
+ ov51x_stop(sd);
+ i2c_w_mask(sd, OV7670_REG_MVFP,
+ OV7670_MVFP_MIRROR * sd->hflip
+ | OV7670_MVFP_VFLIP * sd->vflip,
+ OV7670_MVFP_MIRROR | OV7670_MVFP_VFLIP);
+ if (sd->gspca_dev.streaming)
+ ov51x_restart(sd);
+}
+
+static int set_ov_sensor_window(struct sd *sd)
+{
+ struct gspca_dev *gspca_dev;
+ int qvga;
int hwsbase, hwebase, vwsbase, vwebase, hwscale, vwscale;
int ret, hstart, hstop, vstop, vstart;
__u8 v;
+ gspca_dev = &sd->gspca_dev;
+ qvga = gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv;
+
/* The different sensor ICs handle setting up of window differently.
* IF YOU SET IT WRONG, YOU WILL GET ALL ZERO ISOC DATA FROM OV51x!! */
switch (sd->sensor) {
switch (sd->sensor) {
case SEN_OV6620:
case SEN_OV6630:
- if (win->quarter) { /* QCIF */
+ if (qvga) { /* QCIF */
hwscale = 0;
vwscale = 0;
} else { /* CIF */
}
break;
case SEN_OV8610:
- if (win->quarter) { /* QSVGA */
+ if (qvga) { /* QSVGA */
hwscale = 1;
vwscale = 1;
} else { /* SVGA */
}
break;
default: /* SEN_OV7xx0 */
- if (win->quarter) { /* QVGA */
+ if (qvga) { /* QVGA */
hwscale = 1;
vwscale = 0;
} else { /* VGA */
}
}
- ret = mode_init_ov_sensor_regs(sd, win);
+ ret = mode_init_ov_sensor_regs(sd);
if (ret < 0)
return ret;
/* I can hard code this for OV7670s */
/* Yes, these numbers do look odd, but they're tested and work! */
if (sd->sensor == SEN_OV7670) {
- if (win->quarter) { /* QVGA from ov7670.c by
+ if (qvga) { /* QVGA from ov7670.c by
* Jonathan Corbet */
hstart = 164;
hstop = 20;
}
/* OV7670 hardware window registers are split across
* multiple locations */
- i2c_w(sd, OV7670_REG_HSTART, (hstart >> 3) & 0xff);
- i2c_w(sd, OV7670_REG_HSTOP, (hstop >> 3) & 0xff);
+ i2c_w(sd, OV7670_REG_HSTART, hstart >> 3);
+ i2c_w(sd, OV7670_REG_HSTOP, hstop >> 3);
v = i2c_r(sd, OV7670_REG_HREF);
v = (v & 0xc0) | ((hstop & 0x7) << 3) | (hstart & 0x07);
msleep(10); /* need to sleep between read and write to
* same reg! */
i2c_w(sd, OV7670_REG_HREF, v);
- i2c_w(sd, OV7670_REG_VSTART, (vstart >> 2) & 0xff);
- i2c_w(sd, OV7670_REG_VSTOP, (vstop >> 2) & 0xff);
+ i2c_w(sd, OV7670_REG_VSTART, vstart >> 2);
+ i2c_w(sd, OV7670_REG_VSTOP, vstop >> 2);
v = i2c_r(sd, OV7670_REG_VREF);
v = (v & 0xc0) | ((vstop & 0x3) << 2) | (vstart & 0x03);
msleep(10); /* need to sleep between read and write to
* same reg! */
i2c_w(sd, OV7670_REG_VREF, v);
-
+ sethvflip(sd);
} else {
- i2c_w(sd, 0x17, hwsbase + (win->x >> hwscale));
- i2c_w(sd, 0x18, hwebase + ((win->x + win->width) >> hwscale));
- i2c_w(sd, 0x19, vwsbase + (win->y >> vwscale));
- i2c_w(sd, 0x1a, vwebase + ((win->y + win->height) >> vwscale));
+ i2c_w(sd, 0x17, hwsbase);
+ i2c_w(sd, 0x18, hwebase + (sd->gspca_dev.width >> hwscale));
+ i2c_w(sd, 0x19, vwsbase);
+ i2c_w(sd, 0x1a, vwebase + (sd->gspca_dev.height >> vwscale));
}
return 0;
}
-static int ov_sensor_mode_setup(struct sd *sd,
- int width, int height)
-{
- struct ovsensor_window win;
-
-/* win.format = mode; */
-
- /* Unless subcapture is enabled,
- * center the image window and downsample
- * if possible to increase the field of view */
- /* NOTE: OV518(+) and OV519 does downsampling on its own */
- win.width = width;
- win.height = height;
- if (width == sd->maxwidth)
- win.quarter = 0;
- else
- win.quarter = 1;
-
- /* Center it */
- win.x = (win.width - width) / 2;
- win.y = (win.height - height) / 2;
-
- /* Clock is determined by OV519 frame rate code */
- win.clockdiv = sd->clockdiv;
-
- PDEBUG(D_CONF, "Setting clock divider to %d", win.clockdiv);
- return set_ov_sensor_window(sd, &win);
-}
-
/* -- start the camera -- */
static void sd_start(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
int ret;
-
- ret = ov519_mode_init_regs(sd, gspca_dev->width, gspca_dev->height);
+ ret = ov519_mode_init_regs(sd);
if (ret < 0)
goto out;
- ret = ov_sensor_mode_setup(sd, gspca_dev->width, gspca_dev->height);
+ ret = set_ov_sensor_window(sd);
if (ret < 0)
goto out;
- ret = ov51x_restart((struct sd *) gspca_dev);
+ ret = ov51x_restart(sd);
if (ret < 0)
goto out;
PDEBUG(D_STREAM, "camera started alt: 0x%02x", gspca_dev->alt);
{
struct sd *sd = (struct sd *) gspca_dev;
int val;
-/* int was_streaming; */
val = sd->brightness;
PDEBUG(D_CONF, "brightness:%d", val);
-/* was_streaming = gspca_dev->streaming;
- * if (was_streaming)
+/* if (gspca_dev->streaming)
* ov51x_stop(sd); */
switch (sd->sensor) {
case SEN_OV8610:
i2c_w(sd, OV7610_REG_BRT, val);
break;
case SEN_OV7670:
-/*jfm - from windblows
+/*win trace
* i2c_w_mask(sd, OV7670_REG_COM8, 0, OV7670_COM8_AEC); */
i2c_w(sd, OV7670_REG_BRIGHT, ov7670_abs_to_sm(val));
break;
}
-/* if (was_streaming)
+/* if (gspca_dev->streaming)
* ov51x_restart(sd); */
}
{
struct sd *sd = (struct sd *) gspca_dev;
int val;
-/* int was_streaming; */
val = sd->contrast;
PDEBUG(D_CONF, "contrast:%d", val);
-/* was_streaming = gspca_dev->streaming;
- if (was_streaming)
+/* if (gspca_dev->streaming)
ov51x_stop(sd); */
switch (sd->sensor) {
case SEN_OV7610:
i2c_w(sd, OV7670_REG_CONTRAS, val >> 1);
break;
}
-/* if (was_streaming)
+/* if (gspca_dev->streaming)
ov51x_restart(sd); */
}
{
struct sd *sd = (struct sd *) gspca_dev;
int val;
-/* int was_streaming; */
val = sd->colors;
PDEBUG(D_CONF, "saturation:%d", val);
-/* was_streaming = gspca_dev->streaming;
- if (was_streaming)
+/* if (gspca_dev->streaming)
ov51x_stop(sd); */
switch (sd->sensor) {
case SEN_OV8610:
/* set REG_COM13 values for UV sat auto mode */
break;
}
-/* if (was_streaming)
+/* if (gspca_dev->streaming)
ov51x_restart(sd); */
}
return 0;
}
+static int sd_sethflip(struct gspca_dev *gspca_dev, __s32 val)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ sd->hflip = val;
+ sethvflip(sd);
+ return 0;
+}
+
+static int sd_gethflip(struct gspca_dev *gspca_dev, __s32 *val)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ *val = sd->hflip;
+ return 0;
+}
+
+static int sd_setvflip(struct gspca_dev *gspca_dev, __s32 val)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ sd->vflip = val;
+ sethvflip(sd);
+ return 0;
+}
+
+static int sd_getvflip(struct gspca_dev *gspca_dev, __s32 *val)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ *val = sd->vflip;
+ return 0;
+}
+
/* sub-driver description */
static const struct sd_desc sd_desc = {
.name = MODULE_NAME,
module_param(frame_rate, int, 0644);
MODULE_PARM_DESC(frame_rate, "Frame rate (5, 10, 15, 20 or 30 fps)");
-
struct sd {
struct gspca_dev gspca_dev; /* !! must be the first item */
- int avg_lum;
+ int lum_sum;
+ atomic_t avg_lum;
+ atomic_t do_gain;
unsigned char brightness;
unsigned char contrast;
sd->contrast = CONTRAST_DEF;
sd->colors = COLOR_DEF;
sd->autogain = AUTOGAIN_DEF;
+ sd->ag_cnt = -1;
return 0;
}
PDEBUG(D_CONF|D_STREAM, "color: %i", sd->colors);
}
+static void setautogain(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ if (sd->autogain) {
+ sd->lum_sum = 0;
+ sd->ag_cnt = AG_CNT_START;
+ } else {
+ sd->ag_cnt = -1;
+ }
+}
+
/* this function is called at open time */
static int sd_open(struct gspca_dev *gspca_dev)
{
static void sd_start(struct gspca_dev *gspca_dev)
{
- struct sd *sd = (struct sd *) gspca_dev;
-
reg_w(gspca_dev, 0xff, 0x01);
reg_w_buf(gspca_dev, 0x0002, "\x48\x0a\x40\x08\x00\x00\x08\x00", 8);
reg_w_buf(gspca_dev, 0x000a, "\x06\xff\x11\xff\x5a\x30\x90\x4c", 8);
setcontrast(gspca_dev);
setbrightness(gspca_dev);
setcolors(gspca_dev);
+ setautogain(gspca_dev);
/* set correct resolution */
switch (gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv) {
reg_w(gspca_dev, 0xff, 0x01);
reg_w(gspca_dev, 0x78, 0x04);
reg_w(gspca_dev, 0x78, 0x05);
-
- if (sd->autogain) {
- sd->ag_cnt = AG_CNT_START;
- sd->avg_lum = 0;
- } else {
- sd->ag_cnt = -1;
- }
}
static void sd_stopN(struct gspca_dev *gspca_dev)
reg_w(gspca_dev, 0x78, 0x44); /* Bit_0=start stream, Bit_7=LED */
}
-static void setautogain(struct gspca_dev *gspca_dev, int luma)
+static void do_autogain(struct gspca_dev *gspca_dev)
{
+ struct sd *sd = (struct sd *) gspca_dev;
+ int luma;
int luma_mean = 128;
int luma_delta = 20;
__u8 spring = 5;
int Gbright;
+ if (!atomic_read(&sd->do_gain))
+ return;
+ atomic_set(&sd->do_gain, 0);
+
+ luma = atomic_read(&sd->avg_lum);
Gbright = reg_r(gspca_dev, 0x02);
PDEBUG(D_FRAM, "luma mean %d", luma);
if (luma < luma_mean - luma_delta ||
/* start of frame */
if (sd->ag_cnt >= 0 && p > 28) {
- sd->avg_lum += data[p - 23];
+ sd->lum_sum += data[p - 23];
if (--sd->ag_cnt < 0) {
sd->ag_cnt = AG_CNT_START;
- setautogain(gspca_dev,
- sd->avg_lum / AG_CNT_START);
- sd->avg_lum = 0;
+ atomic_set(&sd->avg_lum,
+ sd->lum_sum / AG_CNT_START);
+ sd->lum_sum = 0;
+ atomic_set(&sd->do_gain, 1);
}
}
struct sd *sd = (struct sd *) gspca_dev;
sd->autogain = val;
- if (val) {
- sd->ag_cnt = AG_CNT_START;
- sd->avg_lum = 0;
- } else {
- sd->ag_cnt = -1;
- }
+ if (gspca_dev->streaming)
+ setautogain(gspca_dev);
return 0;
}
.stop0 = sd_stop0,
.close = sd_close,
.pkt_scan = sd_pkt_scan,
+ .dq_callback = do_autogain,
};
/* -- module initialisation -- */
const __u8 *buffer,
int len)
{
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (len > sizeof gspca_dev->usb_buf) {
PDEBUG(D_ERR|D_PACK, "reg_w: buffer overflow");
return;
struct sd {
struct gspca_dev gspca_dev; /* !! must be the first item */
- int avg_lum;
+ atomic_t avg_lum;
unsigned int exposure;
unsigned short brightness;
/*Data from sn9c102p+hv71331r */
static const __u8 sn_hv7131[] = {
-/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 reg8 reg9 */
- 0x00, 0x03, 0x64, 0x00, 0x1A, 0x20, 0x20, 0x20, 0xA1, 0x11,
-/* rega regb regc regd rege regf reg10 reg11 */
- 0x02, 0x09, 0x00, 0x00, 0x00, 0x10, 0x03, 0x00, /* 00 */
-/* reg12 reg13 reg14 reg15 reg16 reg17 reg18 reg19 reg1a reg1b */
- 0x00, 0x01, 0x03, 0x28, 0x1e, 0x41, 0x0a, 0x00, 0x00, 0x00,
-/* reg1c reg1d reg1e reg1f reg20 reg21 reg22 reg23 */
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 */
+ 0x00, 0x03, 0x64, 0x00, 0x1a, 0x20, 0x20, 0x20,
+/* reg8 reg9 rega regb regc regd rege regf */
+ 0xa1, 0x11, 0x02, 0x09, 0x00, 0x00, 0x00, 0x10,
+/* reg10 reg11 reg12 reg13 reg14 reg15 reg16 reg17 */
+ 0x03, 0x00, 0x00, 0x01, 0x03, 0x28, 0x1e, 0x41,
+/* reg18 reg19 reg1a reg1b reg1c reg1d reg1e reg1f */
+ 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
static const __u8 sn_mi0360[] = {
-/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 reg8 reg9 */
- 0x00, 0x61, 0x44, 0x00, 0x1a, 0x20, 0x20, 0x20, 0xb1, 0x5d,
-/* rega regb regc regd rege regf reg10 reg11 */
- 0x07, 0x00, 0x00, 0x00, 0x00, 0x10, 0x03, 0x00,
-/* reg12 reg13 reg14 reg15 reg16 reg17 reg18 reg19 reg1a reg1b */
- 0x00, 0x02, 0x0a, 0x28, 0x1e, 0x61, 0x06, 0x00, 0x00, 0x00,
-/* reg1c reg1d reg1e reg1f reg20 reg21 reg22 reg23 */
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 */
+ 0x00, 0x61, 0x44, 0x00, 0x1a, 0x20, 0x20, 0x20,
+/* reg8 reg9 rega regb regc regd rege regf */
+ 0xb1, 0x5d, 0x07, 0x00, 0x00, 0x00, 0x00, 0x10,
+/* reg10 reg11 reg12 reg13 reg14 reg15 reg16 reg17 */
+ 0x03, 0x00, 0x00, 0x02, 0x0a, 0x28, 0x1e, 0x61,
+/* reg18 reg19 reg1a reg1b reg1c reg1d reg1e reg1f */
+ 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
static const __u8 sn_mo4000[] = {
-/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 reg8 */
- 0x12, 0x23, 0x60, 0x00, 0x1A, 0x00, 0x20, 0x18, 0x81,
-/* reg9 rega regb regc regd rege regf reg10 reg11*/
- 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x00,
-/* reg12 reg13 reg14 reg15 reg16 reg17 reg18 reg19 reg1a*/
- 0x0b, 0x0f, 0x14, 0x28, 0x1e, 0x40, 0x08, 0x00, 0x00,
-/* reg1b reg1c reg1d reg1e reg1f reg20 reg21 reg22 reg23*/
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x08, 0x25, 0x39, 0x4b,
- 0x5c, 0x6b, 0x79, 0x87, 0x95, 0xa2, 0xaf, 0xbb, 0xc7,
- 0xd3, 0xdf, 0xea, 0xf5
+/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 */
+ 0x12, 0x23, 0x60, 0x00, 0x1a, 0x00, 0x20, 0x18,
+/* reg8 reg9 rega regb regc regd rege regf */
+ 0x81, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/* reg10 reg11 reg12 reg13 reg14 reg15 reg16 reg17 */
+ 0x03, 0x00, 0x0b, 0x0f, 0x14, 0x28, 0x1e, 0x40,
+/* reg18 reg19 reg1a reg1b reg1c reg1d reg1e reg1f */
+ 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
static const __u8 sn_ov7648[] = {
- 0x00, 0x21, 0x62, 0x00, 0x1a, 0x20, 0x20, 0x20, 0xA1, 0x6E, 0x18, 0x65,
- 0x00, 0x00, 0x00, 0x10, 0x03, 0x00, 0x00, 0x06, 0x06, 0x28, 0x1E, 0x82,
- 0x07, 0x00, 0x00, 0x00, 0x00, 0x00
+/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 */
+ 0x00, 0x21, 0x62, 0x00, 0x1a, 0x20, 0x20, 0x20,
+/* reg8 reg9 rega regb regc regd rege regf */
+ 0xa1, 0x6e, 0x18, 0x65, 0x00, 0x00, 0x00, 0x10,
+/* reg10 reg11 reg12 reg13 reg14 reg15 reg16 reg17 */
+ 0x03, 0x00, 0x00, 0x06, 0x06, 0x28, 0x1e, 0x82,
+/* reg18 reg19 reg1a reg1b reg1c reg1d reg1e reg1f */
+ 0x07, 0x00, 0x00, 0x00, 0x00, 0x00
};
static const __u8 sn_ov7660[] = {
-/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 reg8 */
- 0x00, 0x61, 0x40, 0x00, 0x1a, 0x00, 0x00, 0x00, 0x81,
-/* reg9 rega regb regc regd rege regf reg10 reg11*/
- 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x00,
-/* reg12 reg13 reg14 reg15 reg16 reg17 reg18 reg19 reg1a*/
- 0x01, 0x01, 0x14, 0x28, 0x1e, 0x00, 0x07, 0x00, 0x00,
-/* reg1b reg1c reg1d reg1e reg1f reg20 reg21 reg22 reg23*/
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+/* reg0 reg1 reg2 reg3 reg4 reg5 reg6 reg7 */
+ 0x00, 0x61, 0x40, 0x00, 0x1a, 0x20, 0x20, 0x20,
+/* reg8 reg9 rega regb regc regd rege regf */
+ 0x81, 0x21, 0x07, 0x00, 0x00, 0x00, 0x00, 0x10,
+/* reg10 reg11 reg12 reg13 reg14 reg15 reg16 reg17 */
+ 0x03, 0x00, 0x01, 0x01, 0x08, 0x28, 0x1e, 0x20,
+/* reg18 reg19 reg1a reg1b reg1c reg1d reg1e reg1f */
+ 0x07, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
};
/* sequence specific to the sensors - !! index = SENSOR_xxx */
0x00, 0x2d, 0x46, 0x5a, 0x6c, 0x7c, 0x8b, 0x99,
0xa6, 0xb2, 0xbf, 0xca, 0xd5, 0xe0, 0xeb, 0xf5, 0xff
};
-static const __u8 regsn20_sn9c120[] = {
- 0x00, 0x25, 0x3c, 0x50, 0x62, 0x72, 0x81, 0x90,
- 0x9e, 0xab, 0xb8, 0xc5, 0xd1, 0xdd, 0xe9, 0xf4, 0xff
-};
static const __u8 regsn20_sn9c325[] = {
0x0a, 0x3a, 0x56, 0x6c, 0x7e, 0x8d, 0x9a, 0xa4,
0xaf, 0xbb, 0xc5, 0xcd, 0xd5, 0xde, 0xe8, 0xed, 0xf5
/* 0x00, 0x00, 0x00, 0x00, 0x00 */
0xf7, 0x0f, 0x0a, 0x00, 0x00
};
-static const __u8 reg84_sn9c120_1[] = {
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x0c, 0x00, 0x00
-};
-static const __u8 reg84_sn9c120_2[] = {
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
- 0x00, 0x00, 0x0c, 0x02, 0x3b
-};
-static const __u8 reg84_sn9c120_3[] = {
- 0x14, 0x00, 0x27, 0x00, 0x08, 0x00, 0xeb, 0x0f,
- 0xd5, 0x0f, 0x42, 0x00, 0x41, 0x00, 0xca, 0x0f,
- 0xf5, 0x0f, 0x0c, 0x02, 0x3b
-};
static const __u8 reg84_sn9c325[] = {
0x14, 0x00, 0x27, 0x00, 0x07, 0x00, 0xe4, 0x0f,
0xd3, 0x0f, 0x4b, 0x00, 0x48, 0x00, 0xc0, 0x0f,
{0xa1, 0x21, 0x12, 0x80, 0x00, 0x00, 0x00, 0x10}, /* reset SCCB */
/* (delay 20ms) */
{0xa1, 0x21, 0x12, 0x05, 0x00, 0x00, 0x00, 0x10},
- /* Outformat ?? rawRGB */
+ /* Outformat = rawRGB */
{0xa1, 0x21, 0x13, 0xb8, 0x00, 0x00, 0x00, 0x10}, /* init COM8 */
- {0xd1, 0x21, 0x00, 0x01, 0x74, 0x92, 0x00, 0x10},
-/* {0xd1, 0x21, 0x00, 0x01, 0x74, 0x74, 0x00, 0x10}, */
+ {0xd1, 0x21, 0x00, 0x01, 0x74, 0x74, 0x00, 0x10},
/* GAIN BLUE RED VREF */
{0xd1, 0x21, 0x04, 0x00, 0x7d, 0x62, 0x00, 0x10},
/* COM 1 BAVE GEAVE AECHH */
{0xb1, 0x21, 0x08, 0x83, 0x01, 0x00, 0x00, 0x10}, /* RAVE COM2 */
{0xd1, 0x21, 0x0c, 0x00, 0x08, 0x04, 0x4f, 0x10}, /* COM 3 4 5 6 */
- {0xd1, 0x21, 0x10, 0x7f, 0x40, 0x05, 0xf8, 0x10},
-/* {0xd1, 0x21, 0x10, 0x7f, 0x40, 0x05, 0xff, 0x10}, */
+ {0xd1, 0x21, 0x10, 0x7f, 0x40, 0x05, 0xff, 0x10},
/* AECH CLKRC COM7 COM8 */
{0xc1, 0x21, 0x14, 0x2c, 0x00, 0x02, 0x00, 0x10}, /* COM9 COM10 */
{0xd1, 0x21, 0x17, 0x10, 0x60, 0x02, 0x7b, 0x10},
{0xb1, 0x21, 0x1e, 0x01, 0x0e, 0x00, 0x00, 0x10}, /* MVFP LAEC */
{0xd1, 0x21, 0x20, 0x07, 0x07, 0x07, 0x07, 0x10},
/* BOS GBOS GROS ROS (BGGR offset) */
- {0xd1, 0x21, 0x24, 0x68, 0x58, 0xd4, 0x80, 0x10},
-/* {0xd1, 0x21, 0x24, 0x78, 0x68, 0xd4, 0x80, 0x10}, */
+/* {0xd1, 0x21, 0x24, 0x68, 0x58, 0xd4, 0x80, 0x10}, */
+ {0xd1, 0x21, 0x24, 0x78, 0x68, 0xd4, 0x80, 0x10},
/* AEW AEB VPT BBIAS */
{0xd1, 0x21, 0x28, 0x80, 0x30, 0x00, 0x00, 0x10},
/* GbBIAS RSVD EXHCH EXHCL */
{0xd1, 0x21, 0x62, 0x00, 0x00, 0x50, 0x30, 0x10},
/* LCC1 LCC2 LCC3 LCC4 */
{0xa1, 0x21, 0x66, 0x00, 0x00, 0x00, 0x00, 0x10}, /* LCC5 */
- {0xd1, 0x21, 0x67, 0x80, 0x7a, 0x90, 0x80, 0x10},
+ {0xd1, 0x21, 0x67, 0x80, 0x7a, 0x90, 0x80, 0x10}, /* MANU */
{0xa1, 0x21, 0x6b, 0x0a, 0x00, 0x00, 0x00, 0x10},
- /* band gap reference [0..3] DBLV */
+ /* band gap reference [0:3] DBLV */
{0xd1, 0x21, 0x6c, 0x30, 0x48, 0x80, 0x74, 0x10}, /* gamma curve */
{0xd1, 0x21, 0x70, 0x64, 0x60, 0x5c, 0x58, 0x10}, /* gamma curve */
{0xd1, 0x21, 0x74, 0x54, 0x4c, 0x40, 0x38, 0x10}, /* gamma curve */
{0xd1, 0x21, 0x84, 0x6e, 0x77, 0x87, 0x95, 0x10}, /* gamma curve */
{0xc1, 0x21, 0x88, 0xaf, 0xc7, 0xdf, 0x00, 0x10}, /* gamma curve */
{0xc1, 0x21, 0x8b, 0x99, 0x99, 0xcf, 0x00, 0x10}, /* reserved */
- {0xb1, 0x21, 0x92, 0x00, 0x00, 0x00, 0x00, 0x10},
+ {0xb1, 0x21, 0x92, 0x00, 0x00, 0x00, 0x00, 0x10}, /* DM_LNL/H */
/****** (some exchanges in the win trace) ******/
- {0xa1, 0x21, 0x1e, 0x01, 0x00, 0x00, 0x00, 0x10},
+ {0xa1, 0x21, 0x1e, 0x01, 0x00, 0x00, 0x00, 0x10}, /* MVFP */
/* bits[3..0]reserved */
{0xa1, 0x21, 0x1e, 0x01, 0x00, 0x00, 0x00, 0x10},
{0xa1, 0x21, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10},
/* VREF vertical frame ctrl */
{0xa1, 0x21, 0x03, 0x00, 0x00, 0x00, 0x00, 0x10},
- {0xa1, 0x21, 0x10, 0x20, 0x00, 0x00, 0x00, 0x10}, /* 0x20 */
- {0xa1, 0x21, 0x2d, 0x00, 0x00, 0x00, 0x00, 0x10},
- {0xa1, 0x21, 0x2e, 0x00, 0x00, 0x00, 0x00, 0x10},
-/* {0xa1, 0x21, 0x00, 0x1f, 0x00, 0x00, 0x00, 0x10}, */
- {0xa1, 0x21, 0x00, 0x0a, 0x00, 0x00, 0x00, 0x10},
- {0xb1, 0x21, 0x01, 0x78, 0x78, 0x00, 0x00, 0x10},
+ {0xa1, 0x21, 0x10, 0x20, 0x00, 0x00, 0x00, 0x10}, /* AECH 0x20 */
+ {0xa1, 0x21, 0x2d, 0x00, 0x00, 0x00, 0x00, 0x10}, /* ADVFL */
+ {0xa1, 0x21, 0x2e, 0x00, 0x00, 0x00, 0x00, 0x10}, /* ADVFH */
+ {0xa1, 0x21, 0x00, 0x1f, 0x00, 0x00, 0x00, 0x10}, /* GAIN */
+/* {0xb1, 0x21, 0x01, 0x78, 0x78, 0x00, 0x00, 0x10}, * BLUE */
/****** (some exchanges in the win trace) ******/
{0xa1, 0x21, 0x93, 0x00, 0x00, 0x00, 0x00, 0x10},/* dummy line hight */
- {0xa1, 0x21, 0x92, 0x25, 0x00, 0x00, 0x00, 0x10},/* dummy line low */
- {0xa1, 0x21, 0x2a, 0x00, 0x00, 0x00, 0x00, 0x10},
- {0xa1, 0x21, 0x2b, 0x00, 0x00, 0x00, 0x00, 0x10},
- {0xa1, 0x21, 0x02, 0x90, 0x00, 0x00, 0x00, 0x10},
+ {0xa1, 0x21, 0x92, 0x25, 0x00, 0x00, 0x00, 0x10}, /* dummy line low */
+ {0xa1, 0x21, 0x2a, 0x00, 0x00, 0x00, 0x00, 0x10}, /* EXHCH */
+ {0xa1, 0x21, 0x2b, 0x00, 0x00, 0x00, 0x00, 0x10}, /* EXHCL */
+/* {0xa1, 0x21, 0x02, 0x90, 0x00, 0x00, 0x00, 0x10}, * RED */
/****** (some exchanges in the win trace) ******/
-/**********startsensor KO if changed !!****/
+/******!! startsensor KO if changed !!****/
{0xa1, 0x21, 0x93, 0x01, 0x00, 0x00, 0x00, 0x10},
{0xa1, 0x21, 0x92, 0xff, 0x00, 0x00, 0x00, 0x10},
{0xa1, 0x21, 0x2a, 0x00, 0x00, 0x00, 0x00, 0x10},
{0xa1, 0x21, 0x2b, 0xc3, 0x00, 0x00, 0x00, 0x10},
-/* here may start the isoc exchanges */
{}
};
-/* reg0x04 reg0x07 reg 0x10 */
-/* expo = (COM1 & 0x02) | (AECHH & 0x2f <<10) [ (AECh << 2) */
+/* reg 0x04 reg 0x07 reg 0x10 */
+/* expo = (COM1 & 0x02) | ((AECHH & 0x2f) << 10) | (AECh << 2) */
static const __u8 ov7648_sensor_init[][8] = {
{0xC1, 0x00, 0x01, 0x00, 0x00, 0x00, 0x01, 0x00},
const __u8 *reg9a;
static const __u8 reg9a_def[] =
{0x08, 0x40, 0x20, 0x10, 0x00, 0x04};
- static const __u8 reg9a_sn9c120[] = /* from win trace */
- {0x00, 0x40, 0x38, 0x30, 0x00, 0x20};
static const __u8 reg9a_sn9c325[] =
{0x0a, 0x40, 0x38, 0x30, 0x00, 0x20};
+ static const __u8 regd4[] = {0x60, 0x00, 0x00};
reg_w1(gspca_dev, 0xf1, 0x00);
- reg_w1(gspca_dev, 0x01, sn9c1xx[0]); /*fixme:jfm was [1] en v1*/
+ reg_w1(gspca_dev, 0x01, 0x00); /*jfm was sn9c1xx[1] in v1*/
/* configure gpio */
reg_w(gspca_dev, 0x01, &sn9c1xx[1], 2);
case BRIDGE_SN9C325:
reg9a = reg9a_sn9c325;
break;
- case BRIDGE_SN9C120:
- reg9a = reg9a_sn9c120;
- break;
default:
reg9a = reg9a_def;
break;
}
reg_w(gspca_dev, 0x9a, reg9a, 6);
- reg_w1(gspca_dev, 0xd4, 0x60); /*fixme:jfm 60 00 00 (3) ? */
+ reg_w(gspca_dev, 0xd4, regd4, sizeof regd4); /*fixme:jfm was 60 only*/
reg_w(gspca_dev, 0x03, &sn9c1xx[3], 0x0f);
switch (sd->bridge) {
- case BRIDGE_SN9C120: /* from win trace */
- reg_w1(gspca_dev, 0x01, 0x61);
- reg_w1(gspca_dev, 0x17, 0x20);
- reg_w1(gspca_dev, 0x01, 0x60);
- break;
case BRIDGE_SN9C325:
reg_w1(gspca_dev, 0x01, 0x43);
reg_w1(gspca_dev, 0x17, 0xae);
sd->contrast = CONTRAST_DEF;
sd->colors = COLOR_DEF;
sd->autogain = AUTOGAIN_DEF;
+ sd->ag_cnt = -1;
+
return 0;
}
/* setup a selector by bridge */
reg_w1(gspca_dev, 0xf1, 0x01);
- reg_r(gspca_dev, 0x00, 1); /* -> regF1 = 0x00 */
- reg_w1(gspca_dev, 0xf1, gspca_dev->usb_buf[0]);
reg_r(gspca_dev, 0x00, 1);
+ reg_w1(gspca_dev, 0xf1, gspca_dev->usb_buf[0]);
+ reg_r(gspca_dev, 0x00, 1); /* get sonix chip id */
regF1 = gspca_dev->usb_buf[0];
+ PDEBUG(D_PROBE, "Sonix chip id: %02x", regF1);
switch (sd->bridge) {
case BRIDGE_SN9C102P:
if (regF1 != 0x11)
sd->exposure = setexposure(gspca_dev, expo);
break;
case SENSOR_MI0360:
- expo = sd->brightness >> 4;
- sd->exposure = setexposure(gspca_dev, expo);
- break;
case SENSOR_MO4000:
expo = sd->brightness >> 4;
sd->exposure = setexposure(gspca_dev, expo);
break;
- case SENSOR_OV7660:
- return; /*jfm??*/
}
k2 = sd->brightness >> 10;
__u8 k2;
__u8 contrast[] = { 0x00, 0x00, 0x28, 0x00, 0x07, 0x00 };
- if (sd->sensor == SENSOR_OV7660)
- return; /*jfm??*/
k2 = sd->contrast;
contrast[2] = k2;
contrast[0] = (k2 + 1) >> 1;
reg_w1(gspca_dev, 0x05, data);
}
+static void setautogain(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ switch (sd->sensor) {
+ case SENSOR_HV7131R:
+ case SENSOR_MO4000:
+ case SENSOR_MI0360:
+ if (sd->autogain)
+ sd->ag_cnt = AG_CNT_START;
+ else
+ sd->ag_cnt = -1;
+ break;
+ }
+}
+
/* -- start the camera -- */
static void sd_start(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
int i;
- __u8 data;
- __u8 reg1;
- __u8 reg17;
+ __u8 reg1, reg17, reg18;
const __u8 *sn9c1xx;
int mode;
static const __u8 C0[] = { 0x2d, 0x2d, 0x3a, 0x05, 0x04, 0x3f };
static const __u8 CA[] = { 0x28, 0xd8, 0x14, 0xec };
- static const __u8 CA_sn9c120[] =
- { 0x14, 0xec, 0x0a, 0xf6 }; /* SN9C120 */
static const __u8 CE[] = { 0x32, 0xdd, 0x2d, 0xdd }; /* MI0360 */
static const __u8 CE_sn9c325[] =
{ 0x32, 0xdd, 0x32, 0xdd }; /* OV7648 - SN9C325 */
sn9c1xx = sn_tb[(int) sd->sensor];
configure_gpio(gspca_dev, sn9c1xx);
-/*fixme:jfm this sequence should appear at end of sd_start */
-/* with
- reg_w1(gspca_dev, 0x01, 0x44); */
+/* reg_w1(gspca_dev, 0x01, 0x44); jfm from win trace*/
reg_w1(gspca_dev, 0x15, sn9c1xx[0x15]);
reg_w1(gspca_dev, 0x16, sn9c1xx[0x16]);
reg_w1(gspca_dev, 0x12, sn9c1xx[0x12]);
reg_w1(gspca_dev, 0xc7, 0x00);
reg_w1(gspca_dev, 0xc8, 0x50);
reg_w1(gspca_dev, 0xc9, 0x3c);
-/*fixme:jfm end of ending sequence */
reg_w1(gspca_dev, 0x18, sn9c1xx[0x18]);
switch (sd->bridge) {
case BRIDGE_SN9C325:
- data = 0xae;
- break;
- case BRIDGE_SN9C120:
- data = 0xa0;
+ reg17 = 0xae;
break;
default:
- data = 0x60;
+ reg17 = 0x60;
break;
}
- reg_w1(gspca_dev, 0x17, data);
+ reg_w1(gspca_dev, 0x17, reg17);
reg_w1(gspca_dev, 0x05, sn9c1xx[5]);
reg_w1(gspca_dev, 0x07, sn9c1xx[7]);
reg_w1(gspca_dev, 0x06, sn9c1xx[6]);
reg_w1(gspca_dev, 0x9a, 0x0a);
reg_w1(gspca_dev, 0x99, 0x60);
break;
- case BRIDGE_SN9C120:
- reg_w(gspca_dev, 0x20, regsn20_sn9c120,
- sizeof regsn20_sn9c120);
- for (i = 0; i < 2; i++)
- reg_w(gspca_dev, 0x84, reg84_sn9c120_1,
- sizeof reg84_sn9c120_1);
- for (i = 0; i < 6; i++)
- reg_w(gspca_dev, 0x84, reg84_sn9c120_2,
- sizeof reg84_sn9c120_2);
- reg_w(gspca_dev, 0x84, reg84_sn9c120_3,
- sizeof reg84_sn9c120_3);
- reg_w1(gspca_dev, 0x9a, 0x05);
- reg_w1(gspca_dev, 0x99, 0x5b);
- break;
default:
reg_w(gspca_dev, 0x20, regsn20, sizeof regsn20);
for (i = 0; i < 8; i++)
/* reg1 = 0x44; */
/* reg1 = 0x46; (done) */
} else {
- reg17 = 0xa2; /* 640 */
- reg1 = 0x40;
+ reg17 = 0x22; /* 640 MCKSIZE */
+ reg1 = 0x06;
}
break;
}
reg_w(gspca_dev, 0xc0, C0, 6);
+ reg_w(gspca_dev, 0xca, CA, 4);
switch (sd->bridge) {
- case BRIDGE_SN9C120: /*jfm ?? */
- reg_w(gspca_dev, 0xca, CA_sn9c120, 4);
- break;
- default:
- reg_w(gspca_dev, 0xca, CA, 4);
- break;
- }
- switch (sd->bridge) {
- case BRIDGE_SN9C120: /*jfm ?? */
case BRIDGE_SN9C325:
reg_w(gspca_dev, 0xce, CE_sn9c325, 4);
break;
}
/* here change size mode 0 -> VGA; 1 -> CIF */
- data = 0x40 | sn9c1xx[0x18] | (mode << 4);
- reg_w1(gspca_dev, 0x18, data);
+ reg18 = sn9c1xx[0x18] | (mode << 4);
+ reg_w1(gspca_dev, 0x18, reg18 | 0x40);
reg_w(gspca_dev, 0x100, qtable4, 0x40);
reg_w(gspca_dev, 0x140, qtable4 + 0x40, 0x40);
- data = sn9c1xx[0x18] | (mode << 4);
- reg_w1(gspca_dev, 0x18, data);
+ reg_w1(gspca_dev, 0x18, reg18);
reg_w1(gspca_dev, 0x17, reg17);
reg_w1(gspca_dev, 0x01, reg1);
setbrightness(gspca_dev);
setcontrast(gspca_dev);
+ setautogain(gspca_dev);
}
static void sd_stopN(struct gspca_dev *gspca_dev)
i2c_w8(gspca_dev, stopmi0360);
data = 0x29;
break;
- case SENSOR_MO4000:
- break;
case SENSOR_OV7648:
data = 0x29;
break;
default:
+/* case SENSOR_MO4000: */
/* case SENSOR_OV7660: */
break;
}
{
}
-static void setautogain(struct gspca_dev *gspca_dev)
+static void do_autogain(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
- /* Thanks S., without your advice, autobright should not work :) */
int delta;
- int expotimes = 0;
+ int expotimes;
__u8 luma_mean = 130;
__u8 luma_delta = 20;
- delta = sd->avg_lum;
+ /* Thanks S., without your advice, autobright should not work :) */
+ if (sd->ag_cnt < 0)
+ return;
+ if (--sd->ag_cnt >= 0)
+ return;
+ sd->ag_cnt = AG_CNT_START;
+
+ delta = atomic_read(&sd->avg_lum);
+ PDEBUG(D_FRAM, "mean lum %d", delta);
if (delta < luma_mean - luma_delta ||
delta > luma_mean + luma_delta) {
switch (sd->sensor) {
sd->exposure = setexposure(gspca_dev,
(unsigned int) (expotimes << 8));
break;
- case SENSOR_MO4000:
- case SENSOR_MI0360:
+ default:
+/* case SENSOR_MO4000: */
+/* case SENSOR_MI0360: */
expotimes = sd->exposure;
expotimes += (luma_mean - delta) >> 6;
if (expotimes < 0)
}
}
+/* scan the URB packets */
+/* This function is run at interrupt level. */
static void sd_pkt_scan(struct gspca_dev *gspca_dev,
struct gspca_frame *frame, /* target */
__u8 *data, /* isoc packet */
frame, data, sof + 2);
if (sd->ag_cnt < 0)
return;
- if (--sd->ag_cnt >= 0)
- return;
- sd->ag_cnt = AG_CNT_START;
/* w1 w2 w3 */
/* w4 w5 w6 */
/* w7 w8 */
/* w5 */
avg_lum += ((data[sof + 31] << 8) | data[sof + 32]) >> 4;
avg_lum >>= 4;
- sd->avg_lum = avg_lum;
- PDEBUG(D_PACK, "mean lum %d", avg_lum);
- setautogain(gspca_dev);
+ atomic_set(&sd->avg_lum, avg_lum);
return;
}
if (gspca_dev->last_packet_type == LAST_PACKET) {
(hexpo << 10) | (mexpo << 2) | lexpo);
return (hexpo << 10) | (mexpo << 2) | lexpo;
default:
+/* case SENSOR_OV7648: * jfm: is it ok for 7648? */
/* case SENSOR_OV7660: */
/* read sensor exposure */
i2c_r5(gspca_dev, 0x04);
/* hardcoded registers seem not readable */
switch (sd->sensor) {
case SENSOR_HV7131R:
-/* sd->brightness = 0x7fff; */
sd->brightness = getexposure(gspca_dev) >> 4;
break;
case SENSOR_MI0360:
sd->brightness = getexposure(gspca_dev) << 4;
break;
case SENSOR_MO4000:
-/* sd->brightness = 0x1fff; */
sd->brightness = getexposure(gspca_dev) << 4;
break;
}
struct sd *sd = (struct sd *) gspca_dev;
sd->autogain = val;
- if (val)
- sd->ag_cnt = AG_CNT_START;
- else
- sd->ag_cnt = -1;
+ if (gspca_dev->streaming)
+ setautogain(gspca_dev);
return 0;
}
.stop0 = sd_stop0,
.close = sd_close,
.pkt_scan = sd_pkt_scan,
+ .dq_callback = do_autogain,
};
/* -- module initialisation -- */
static struct v4l2_pix_format vga_mode[] = {
{160, 120, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 160 * 3,
+ .bytesperline = 160,
.sizeimage = 160 * 120 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 5},
{176, 144, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 176 * 3,
+ .bytesperline = 176,
.sizeimage = 176 * 144 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 4},
{320, 240, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 320 * 3,
+ .bytesperline = 320,
.sizeimage = 320 * 240 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 2},
{352, 288, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 352 * 3,
+ .bytesperline = 352,
.sizeimage = 352 * 288 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 1},
{640, 480, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 640 * 3,
+ .bytesperline = 640,
.sizeimage = 640 * 480 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 0},
default:
data += 1;
len -= 1;
- gspca_frame_add(gspca_dev, FIRST_PACKET, frame,
+ gspca_frame_add(gspca_dev, INTER_PACKET, frame,
data, len);
break;
}
static struct v4l2_pix_format vga_mode[] = {
{160, 120, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 160 * 3,
+ .bytesperline = 160,
.sizeimage = 160 * 120 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 5},
{176, 144, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 176 * 3,
+ .bytesperline = 176,
.sizeimage = 176 * 144 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 4},
{320, 240, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 320 * 3,
+ .bytesperline = 320,
.sizeimage = 320 * 240 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 2},
{352, 288, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 352 * 3,
+ .bytesperline = 352,
.sizeimage = 352 * 288 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 1},
{640, 480, V4L2_PIX_FMT_SPCA505, V4L2_FIELD_NONE,
- .bytesperline = 640 * 3,
+ .bytesperline = 640,
.sizeimage = 640 * 480 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 0},
default:
data += 1;
len -= 1;
- gspca_frame_add(gspca_dev, FIRST_PACKET, frame,
+ gspca_frame_add(gspca_dev, INTER_PACKET, frame,
data, len);
break;
}
};
static struct v4l2_pix_format sif_mode[] = {
- {160, 120, V4L2_PIX_FMT_YUYV, V4L2_FIELD_NONE,
- .bytesperline = 160 * 3,
+ {160, 120, V4L2_PIX_FMT_SPCA508, V4L2_FIELD_NONE,
+ .bytesperline = 160,
.sizeimage = 160 * 120 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 3},
- {176, 144, V4L2_PIX_FMT_YUYV, V4L2_FIELD_NONE,
- .bytesperline = 176 * 3,
+ {176, 144, V4L2_PIX_FMT_SPCA508, V4L2_FIELD_NONE,
+ .bytesperline = 176,
.sizeimage = 176 * 144 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 2},
- {320, 240, V4L2_PIX_FMT_YUYV, V4L2_FIELD_NONE,
- .bytesperline = 320 * 3,
+ {320, 240, V4L2_PIX_FMT_SPCA508, V4L2_FIELD_NONE,
+ .bytesperline = 320,
.sizeimage = 320 * 240 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 1},
- {352, 288, V4L2_PIX_FMT_YUYV, V4L2_FIELD_NONE,
- .bytesperline = 352 * 3,
+ {352, 288, V4L2_PIX_FMT_SPCA508, V4L2_FIELD_NONE,
+ .bytesperline = 352,
.sizeimage = 352 * 288 * 3 / 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 0},
default:
data += 1;
len -= 1;
- gspca_frame_add(gspca_dev, FIRST_PACKET, frame,
+ gspca_frame_add(gspca_dev, INTER_PACKET, frame,
data, len);
break;
}
}
}
+static void setautogain(struct gspca_dev *gspca_dev)
+{
+ struct sd *sd = (struct sd *) gspca_dev;
+
+ if (sd->chip_revision == Rev072A) {
+ if (sd->autogain)
+ sd->ag_cnt = AG_CNT_START;
+ else
+ sd->ag_cnt = -1;
+ }
+}
+
static void sd_start(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
reg_w_val(dev, 0x8500, mode); /* mode */
reg_w_val(dev, 0x8700, Clck); /* 0x27 clock */
reg_w_val(dev, 0x8112, 0x10 | 0x20);
+ setautogain(gspca_dev);
break;
default:
/* case Rev012A: */
reg_w_val(gspca_dev->dev, 0x8114, 0);
}
-static void setautogain(struct gspca_dev *gspca_dev)
+static void do_autogain(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
- int expotimes = 0;
- int pixelclk = 0;
- int gainG = 0;
+ int expotimes;
+ int pixelclk;
+ int gainG;
__u8 R, Gr, Gb, B;
int y;
__u8 luma_mean = 110;
__u8 luma_delta = 20;
__u8 spring = 4;
+ if (sd->ag_cnt < 0)
+ return;
+ if (--sd->ag_cnt >= 0)
+ return;
+ sd->ag_cnt = AG_CNT_START;
+
switch (sd->chip_revision) {
case Rev072A:
reg_r(gspca_dev, 0x8621, 1);
__u8 *data, /* isoc packet */
int len) /* iso packet length */
{
- struct sd *sd = (struct sd *) gspca_dev;
-
switch (data[0]) {
case 0: /* start of frame */
frame = gspca_frame_add(gspca_dev, LAST_PACKET, frame,
data, 0);
- if (sd->ag_cnt >= 0) {
- if (--sd->ag_cnt < 0) {
- sd->ag_cnt = AG_CNT_START;
- setautogain(gspca_dev);
- }
- }
data += SPCA561_OFFSET_DATA;
len -= SPCA561_OFFSET_DATA;
if (data[1] & 0x10) {
struct sd *sd = (struct sd *) gspca_dev;
sd->autogain = val;
- if (val)
- sd->ag_cnt = AG_CNT_START;
- else
- sd->ag_cnt = -1;
+ if (gspca_dev->streaming)
+ setautogain(gspca_dev);
return 0;
}
.stop0 = sd_stop0,
.close = sd_close,
.pkt_scan = sd_pkt_scan,
+ .dq_callback = do_autogain,
};
/* -- module initialisation -- */
static struct v4l2_pix_format vc0321_mode[] = {
{320, 240, V4L2_PIX_FMT_YUV420, V4L2_FIELD_NONE,
- .bytesperline = 320 * 2,
+ .bytesperline = 320,
.sizeimage = 320 * 240 * 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 1},
{640, 480, V4L2_PIX_FMT_YUV420, V4L2_FIELD_NONE,
- .bytesperline = 640 * 2,
+ .bytesperline = 640,
.sizeimage = 640 * 480 * 2,
.colorspace = V4L2_COLORSPACE_SRGB,
.priv = 0},
NULL, Tgradient_1, Tgradient_2,
Tgradient_3, Tgradient_4, Tgradient_5, Tgradient_6
};
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
__u8 v[16];
#endif
else if (g <= 0)
g = 1;
reg_w(dev, g, 0x0120 + i); /* gamma */
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (gspca_debug & D_CONF)
v[i] = g;
#endif
g = 1;
}
reg_w(dev, g, 0x0130 + i); /* gradient */
-#ifdef CONFIG_VIDEO_ADV_DEBUG
+#ifdef GSPCA_DEBUG
if (gspca_debug & D_CONF)
v[i] = g;
#endif
static char *sensor_type;
module_param(sensor_type, charp, S_IRUGO);
-MODULE_PARM_DESC(sensor_type, "Sensor type: \"colour\" or \"monochrome\"\n");
+MODULE_PARM_DESC(sensor_type, "Sensor type: \"colour\" or \"monochrome\"");
/* mt9v022 selected register addresses */
#define MT9V022_CHIP_VERSION 0x00
#include <linux/videodev2.h>
#include <asm/dma.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/camera.h>
+#include <mach/pxa-regs.h>
+#include <mach/camera.h>
#define PXA_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5)
#define PXA_CAM_DRV_NAME "pxa27x-camera"
struct pxa_buffer *active;
struct pxa_dma_desc *sg_tail[3];
+
+ u32 save_cicr[5];
};
static const char *pxa_cam_driver_description = "PXA_Camera";
return 0;
}
+static int pxa_camera_suspend(struct soc_camera_device *icd, pm_message_t state)
+{
+ struct soc_camera_host *ici =
+ to_soc_camera_host(icd->dev.parent);
+ struct pxa_camera_dev *pcdev = ici->priv;
+ int i = 0, ret = 0;
+
+ pcdev->save_cicr[i++] = CICR0;
+ pcdev->save_cicr[i++] = CICR1;
+ pcdev->save_cicr[i++] = CICR2;
+ pcdev->save_cicr[i++] = CICR3;
+ pcdev->save_cicr[i++] = CICR4;
+
+ if ((pcdev->icd) && (pcdev->icd->ops->suspend))
+ ret = pcdev->icd->ops->suspend(pcdev->icd, state);
+
+ return ret;
+}
+
+static int pxa_camera_resume(struct soc_camera_device *icd)
+{
+ struct soc_camera_host *ici =
+ to_soc_camera_host(icd->dev.parent);
+ struct pxa_camera_dev *pcdev = ici->priv;
+ int i = 0, ret = 0;
+
+ DRCMR68 = pcdev->dma_chans[0] | DRCMR_MAPVLD;
+ DRCMR69 = pcdev->dma_chans[1] | DRCMR_MAPVLD;
+ DRCMR70 = pcdev->dma_chans[2] | DRCMR_MAPVLD;
+
+ CICR0 = pcdev->save_cicr[i++] & ~CICR0_ENB;
+ CICR1 = pcdev->save_cicr[i++];
+ CICR2 = pcdev->save_cicr[i++];
+ CICR3 = pcdev->save_cicr[i++];
+ CICR4 = pcdev->save_cicr[i++];
+
+ if ((pcdev->icd) && (pcdev->icd->ops->resume))
+ ret = pcdev->icd->ops->resume(pcdev->icd);
+
+ /* Restart frame capture if active buffer exists */
+ if (!ret && pcdev->active) {
+ /* Reset the FIFOs */
+ CIFR |= CIFR_RESET_F;
+ /* Enable End-Of-Frame Interrupt */
+ CICR0 &= ~CICR0_EOFM;
+ /* Restart the Capture Interface */
+ CICR0 |= CICR0_ENB;
+ }
+
+ return ret;
+}
+
static struct soc_camera_host_ops pxa_soc_camera_host_ops = {
.owner = THIS_MODULE,
.add = pxa_camera_add_device,
.remove = pxa_camera_remove_device,
+ .suspend = pxa_camera_suspend,
+ .resume = pxa_camera_resume,
.set_fmt_cap = pxa_camera_set_fmt_cap,
.try_fmt_cap = pxa_camera_try_fmt_cap,
.init_videobuf = pxa_camera_init_videobuf,
static void __exit pxa_camera_exit(void)
{
- return platform_driver_unregister(&pxa_camera_driver);
+ platform_driver_unregister(&pxa_camera_driver);
}
module_init(pxa_camera_init);
static void __exit sh_mobile_ceu_exit(void)
{
- return platform_driver_unregister(&sh_mobile_ceu_driver);
+ platform_driver_unregister(&sh_mobile_ceu_driver);
}
module_init(sh_mobile_ceu_init);
return 0;
}
+static int soc_camera_suspend(struct device *dev, pm_message_t state)
+{
+ struct soc_camera_device *icd = to_soc_camera_dev(dev);
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ int ret = 0;
+
+ if (ici->ops->suspend)
+ ret = ici->ops->suspend(icd, state);
+
+ return ret;
+}
+
+static int soc_camera_resume(struct device *dev)
+{
+ struct soc_camera_device *icd = to_soc_camera_dev(dev);
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ int ret = 0;
+
+ if (ici->ops->resume)
+ ret = ici->ops->resume(icd);
+
+ return ret;
+}
+
static struct bus_type soc_camera_bus_type = {
.name = "soc-camera",
.probe = soc_camera_probe,
.remove = soc_camera_remove,
+ .suspend = soc_camera_suspend,
+ .resume = soc_camera_resume,
};
static struct device_driver ic_drv = {
static void __exit soc_camera_platform_module_exit(void)
{
- return platform_driver_unregister(&soc_camera_platform_driver);
+ platform_driver_unregister(&soc_camera_platform_driver);
}
module_init(soc_camera_platform_module_init);
struct uvc_control_mapping *mapping;
struct uvc_menu_info *menu;
unsigned int i;
- __u8 data[8];
+ __u8 *data;
int ret;
ctrl = uvc_find_control(video, v4l2_ctrl->id, &mapping);
if (ctrl == NULL)
return -EINVAL;
+ data = kmalloc(8, GFP_KERNEL);
+ if (data == NULL)
+ return -ENOMEM;
+
memset(v4l2_ctrl, 0, sizeof *v4l2_ctrl);
v4l2_ctrl->id = mapping->id;
v4l2_ctrl->type = mapping->v4l2_type;
if (ctrl->info->flags & UVC_CONTROL_GET_DEF) {
if ((ret = uvc_query_ctrl(video->dev, GET_DEF, ctrl->entity->id,
video->dev->intfnum, ctrl->info->selector,
- &data, ctrl->info->size)) < 0)
- return ret;
+ data, ctrl->info->size)) < 0)
+ goto out;
v4l2_ctrl->default_value = uvc_get_le_value(data, mapping);
}
}
}
- return 0;
+ ret = 0;
+ goto out;
case V4L2_CTRL_TYPE_BOOLEAN:
v4l2_ctrl->minimum = 0;
v4l2_ctrl->maximum = 1;
v4l2_ctrl->step = 1;
- return 0;
+ ret = 0;
+ goto out;
default:
break;
if (ctrl->info->flags & UVC_CONTROL_GET_MIN) {
if ((ret = uvc_query_ctrl(video->dev, GET_MIN, ctrl->entity->id,
video->dev->intfnum, ctrl->info->selector,
- &data, ctrl->info->size)) < 0)
- return ret;
+ data, ctrl->info->size)) < 0)
+ goto out;
v4l2_ctrl->minimum = uvc_get_le_value(data, mapping);
}
if (ctrl->info->flags & UVC_CONTROL_GET_MAX) {
if ((ret = uvc_query_ctrl(video->dev, GET_MAX, ctrl->entity->id,
video->dev->intfnum, ctrl->info->selector,
- &data, ctrl->info->size)) < 0)
- return ret;
+ data, ctrl->info->size)) < 0)
+ goto out;
v4l2_ctrl->maximum = uvc_get_le_value(data, mapping);
}
if (ctrl->info->flags & UVC_CONTROL_GET_RES) {
if ((ret = uvc_query_ctrl(video->dev, GET_RES, ctrl->entity->id,
video->dev->intfnum, ctrl->info->selector,
- &data, ctrl->info->size)) < 0)
- return ret;
+ data, ctrl->info->size)) < 0)
+ goto out;
v4l2_ctrl->step = uvc_get_le_value(data, mapping);
}
- return 0;
+ ret = 0;
+out:
+ kfree(data);
+ return ret;
}
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX },
- /* Packard Bell OEM Webcam */
+ /* Packard Bell OEM Webcam - Bison Electronics */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
.idVendor = 0x5986,
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX },
- /* Acer Crystal Eye webcam */
+ /* Acer Crystal Eye webcam - Bison Electronics */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
.idVendor = 0x5986,
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX },
- /* Medion Akoya Mini E1210 */
+ /* Medion Akoya Mini E1210 - Bison Electronics */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
.idVendor = 0x5986,
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX },
- /* Acer OrbiCam - Unknown vendor */
+ /* Acer OrbiCam - Bison Electronics */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
.idVendor = 0x5986,
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX },
+ /* Bison Electronics */
+ { .match_flags = USB_DEVICE_ID_MATCH_DEVICE
+ | USB_DEVICE_ID_MATCH_INT_INFO,
+ .idVendor = 0x5986,
+ .idProduct = 0x0300,
+ .bInterfaceClass = USB_CLASS_VIDEO,
+ .bInterfaceSubClass = 1,
+ .bInterfaceProtocol = 0,
+ .driver_info = UVC_QUIRK_PROBE_MINMAX },
+ /* Clevo M570TU - Bison Electronics */
+ { .match_flags = USB_DEVICE_ID_MATCH_DEVICE
+ | USB_DEVICE_ID_MATCH_INT_INFO,
+ .idVendor = 0x5986,
+ .idProduct = 0x0303,
+ .bInterfaceClass = USB_CLASS_VIDEO,
+ .bInterfaceSubClass = 1,
+ .bInterfaceProtocol = 0,
+ .driver_info = UVC_QUIRK_PROBE_MINMAX },
/* Generic USB Video Class */
{ USB_INTERFACE_INFO(USB_CLASS_VIDEO, 1, 0) },
{}
static int uvc_get_video_ctrl(struct uvc_video_device *video,
struct uvc_streaming_control *ctrl, int probe, __u8 query)
{
- __u8 data[34];
- __u8 size;
+ __u8 *data;
+ __u16 size;
int ret;
size = video->dev->uvc_version >= 0x0110 ? 34 : 26;
+ data = kmalloc(size, GFP_KERNEL);
+ if (data == NULL)
+ return -ENOMEM;
+
ret = __uvc_query_ctrl(video->dev, query, 0, video->streaming->intfnum,
- probe ? VS_PROBE_CONTROL : VS_COMMIT_CONTROL, &data, size,
+ probe ? VS_PROBE_CONTROL : VS_COMMIT_CONTROL, data, size,
UVC_CTRL_STREAMING_TIMEOUT);
-
if (ret < 0)
- return ret;
+ goto out;
ctrl->bmHint = le16_to_cpup((__le16 *)&data[0]);
ctrl->bFormatIndex = data[2];
*/
uvc_fixup_buffer_size(video, ctrl);
- return 0;
+out:
+ kfree(data);
+ return ret;
}
int uvc_set_video_ctrl(struct uvc_video_device *video,
struct uvc_streaming_control *ctrl, int probe)
{
- __u8 data[34];
- __u8 size;
+ __u8 *data;
+ __u16 size;
+ int ret;
size = video->dev->uvc_version >= 0x0110 ? 34 : 26;
- memset(data, 0, sizeof data);
+ data = kzalloc(size, GFP_KERNEL);
+ if (data == NULL)
+ return -ENOMEM;
*(__le16 *)&data[0] = cpu_to_le16(ctrl->bmHint);
data[2] = ctrl->bFormatIndex;
data[33] = ctrl->bMaxVersion;
}
- return __uvc_query_ctrl(video->dev, SET_CUR, 0,
+ ret = __uvc_query_ctrl(video->dev, SET_CUR, 0,
video->streaming->intfnum,
- probe ? VS_PROBE_CONTROL : VS_COMMIT_CONTROL, &data, size,
+ probe ? VS_PROBE_CONTROL : VS_COMMIT_CONTROL, data, size,
UVC_CTRL_STREAMING_TIMEOUT);
+
+ kfree(data);
+ return ret;
}
int uvc_probe_video(struct uvc_video_device *video,
EXPORT_SYMBOL(video_register_device);
/**
- * video_register_device - register video4linux devices
+ * video_register_device_index - register video4linux devices
* @vfd: video device structure we want to register
* @type: type of device to register
* @nr: which device number (0 == /dev/video0, 1 == /dev/video1, ...
* -1 == first free)
+ * @index: stream number based on parent device;
+ * -1 if auto assign, requested number otherwise
*
* The registration code assigns minor numbers based on the type
* requested. -ENFILE is returned in all the device slots for this
#include <linux/i2c-algo-sgi.h>
#include <linux/videodev2.h>
+#include <media/v4l2-ioctl.h>
#include <media/v4l2-common.h>
+#include <media/v4l2-ioctl.h>
#include <linux/video_decoder.h>
#include <linux/mutex.h>
#include <linux/platform_device.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/system.h>
-#include <asm/arch/mcp.h>
+#include <mach/mcp.h>
-#include <asm/arch/assabet.h>
+#include <mach/assabet.h>
#include "mcp.h"
#include <linux/mutex.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "ucb1x00.h"
#include <linux/kthread.h>
#include <asm/dma.h>
-#include <asm/arch/collie.h>
+#include <mach/collie.h>
#include <asm/mach-types.h>
#include "ucb1x00.h"
config SGI_XP
tristate "Support communication between SGI SSIs"
- depends on IA64_GENERIC || IA64_SGI_SN2
+ depends on NET
+ depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_64) && SMP
select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select SGI_GRU if (IA64_GENERIC || IA64_SGI_UV || X86_64) && SMP
---help---
An SGI machine can be divided into multiple Single System
Images which act independently of each other and have
To compile this driver as a module, choose M here: the
module will be called hpilo.
+config SGI_GRU
+ tristate "SGI GRU driver"
+ depends on (X86_64 || IA64_SGI_UV || IA64_GENERIC) && SMP
+ default n
+ select MMU_NOTIFIER
+ ---help---
+ The GRU is a hardware resource located in the system chipset. The GRU
+ contains memory that can be mmapped into the user address space. This memory is
+ used to communicate with the GRU to perform functions such as load/store,
+ scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
+ instructions using user virtual addresses. GRU instructions (ex., bcopy) use
+ user virtual addresses for operands.
+
+ If you are not running on a SGI UV system, say N.
+
+config SGI_GRU_DEBUG
+ bool "SGI GRU driver debug"
+ depends on SGI_GRU
+ default n
+ ---help---
+ This option enables addition debugging code for the SGI GRU driver. If
+ you are unsure, say N.
+
endif # MISC_DEVICES
obj-$(CONFIG_ENCLOSURE_SERVICES) += enclosure.o
obj-$(CONFIG_KGDB_TESTS) += kgdbts.o
obj-$(CONFIG_SGI_XP) += sgi-xp/
+obj-$(CONFIG_SGI_GRU) += sgi-gru/
obj-$(CONFIG_HP_ILO) += hpilo.o
--- /dev/null
+obj-$(CONFIG_SGI_GRU) := gru.o
+gru-y := grufile.o grumain.o grufault.o grutlbpurge.o gruprocfs.o grukservices.o
+
--- /dev/null
+/*
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU Lesser General Public License as published by
+ * the Free Software Foundation; either version 2.1 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __GRU_H__
+#define __GRU_H__
+
+/*
+ * GRU architectural definitions
+ */
+#define GRU_CACHE_LINE_BYTES 64
+#define GRU_HANDLE_STRIDE 256
+#define GRU_CB_BASE 0
+#define GRU_DS_BASE 0x20000
+
+/*
+ * Size used to map GRU GSeg
+ */
+#if defined CONFIG_IA64
+#define GRU_GSEG_PAGESIZE (256 * 1024UL)
+#elif defined CONFIG_X86_64
+#define GRU_GSEG_PAGESIZE (256 * 1024UL) /* ZZZ 2MB ??? */
+#else
+#error "Unsupported architecture"
+#endif
+
+/*
+ * Structure for obtaining GRU resource information
+ */
+struct gru_chiplet_info {
+ int node;
+ int chiplet;
+ int blade;
+ int total_dsr_bytes;
+ int total_cbr;
+ int total_user_dsr_bytes;
+ int total_user_cbr;
+ int free_user_dsr_bytes;
+ int free_user_cbr;
+};
+
+/* Flags for GRU options on the gru_create_context() call */
+/* Select one of the follow 4 options to specify how TLB misses are handled */
+#define GRU_OPT_MISS_DEFAULT 0x0000 /* Use default mode */
+#define GRU_OPT_MISS_USER_POLL 0x0001 /* User will poll CB for faults */
+#define GRU_OPT_MISS_FMM_INTR 0x0002 /* Send interrupt to cpu to
+ handle fault */
+#define GRU_OPT_MISS_FMM_POLL 0x0003 /* Use system polling thread */
+#define GRU_OPT_MISS_MASK 0x0003 /* Mask for TLB MISS option */
+
+
+
+#endif /* __GRU_H__ */
--- /dev/null
+/*
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU Lesser General Public License as published by
+ * the Free Software Foundation; either version 2.1 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __GRU_INSTRUCTIONS_H__
+#define __GRU_INSTRUCTIONS_H__
+
+#define gru_flush_cache_hook(p)
+#define gru_emulator_wait_hook(p, w)
+
+/*
+ * Architecture dependent functions
+ */
+
+#if defined CONFIG_IA64
+#include <linux/compiler.h>
+#include <asm/intrinsics.h>
+#define __flush_cache(p) ia64_fc(p)
+/* Use volatile on IA64 to ensure ordering via st4.rel */
+#define gru_ordered_store_int(p,v) \
+ do { \
+ barrier(); \
+ *((volatile int *)(p)) = v; /* force st.rel */ \
+ } while (0)
+#elif defined CONFIG_X86_64
+#define __flush_cache(p) clflush(p)
+#define gru_ordered_store_int(p,v) \
+ do { \
+ barrier(); \
+ *(int *)p = v; \
+ } while (0)
+#else
+#error "Unsupported architecture"
+#endif
+
+/*
+ * Control block status and exception codes
+ */
+#define CBS_IDLE 0
+#define CBS_EXCEPTION 1
+#define CBS_ACTIVE 2
+#define CBS_CALL_OS 3
+
+/* CB substatus bitmasks */
+#define CBSS_MSG_QUEUE_MASK 7
+#define CBSS_IMPLICIT_ABORT_ACTIVE_MASK 8
+
+/* CB substatus message queue values (low 3 bits of substatus) */
+#define CBSS_NO_ERROR 0
+#define CBSS_LB_OVERFLOWED 1
+#define CBSS_QLIMIT_REACHED 2
+#define CBSS_PAGE_OVERFLOW 3
+#define CBSS_AMO_NACKED 4
+#define CBSS_PUT_NACKED 5
+
+/*
+ * Structure used to fetch exception detail for CBs that terminate with
+ * CBS_EXCEPTION
+ */
+struct control_block_extended_exc_detail {
+ unsigned long cb;
+ int opc;
+ int ecause;
+ int exopc;
+ long exceptdet0;
+ int exceptdet1;
+};
+
+/*
+ * Instruction formats
+ */
+
+/*
+ * Generic instruction format.
+ * This definition has precise bit field definitions.
+ */
+struct gru_instruction_bits {
+ /* DW 0 - low */
+ unsigned int icmd: 1;
+ unsigned char ima: 3; /* CB_DelRep, unmapped mode */
+ unsigned char reserved0: 4;
+ unsigned int xtype: 3;
+ unsigned int iaa0: 2;
+ unsigned int iaa1: 2;
+ unsigned char reserved1: 1;
+ unsigned char opc: 8; /* opcode */
+ unsigned char exopc: 8; /* extended opcode */
+ /* DW 0 - high */
+ unsigned int idef2: 22; /* TRi0 */
+ unsigned char reserved2: 2;
+ unsigned char istatus: 2;
+ unsigned char isubstatus:4;
+ unsigned char reserved3: 2;
+ /* DW 1 */
+ unsigned long idef4; /* 42 bits: TRi1, BufSize */
+ /* DW 2-6 */
+ unsigned long idef1; /* BAddr0 */
+ unsigned long idef5; /* Nelem */
+ unsigned long idef6; /* Stride, Operand1 */
+ unsigned long idef3; /* BAddr1, Value, Operand2 */
+ unsigned long reserved4;
+ /* DW 7 */
+ unsigned long avalue; /* AValue */
+};
+
+/*
+ * Generic instruction with friendlier names. This format is used
+ * for inline instructions.
+ */
+struct gru_instruction {
+ /* DW 0 */
+ unsigned int op32; /* icmd,xtype,iaa0,ima,opc */
+ unsigned int tri0;
+ unsigned long tri1_bufsize; /* DW 1 */
+ unsigned long baddr0; /* DW 2 */
+ unsigned long nelem; /* DW 3 */
+ unsigned long op1_stride; /* DW 4 */
+ unsigned long op2_value_baddr1; /* DW 5 */
+ unsigned long reserved0; /* DW 6 */
+ unsigned long avalue; /* DW 7 */
+};
+
+/* Some shifts and masks for the low 32 bits of a GRU command */
+#define GRU_CB_ICMD_SHFT 0
+#define GRU_CB_ICMD_MASK 0x1
+#define GRU_CB_XTYPE_SHFT 8
+#define GRU_CB_XTYPE_MASK 0x7
+#define GRU_CB_IAA0_SHFT 11
+#define GRU_CB_IAA0_MASK 0x3
+#define GRU_CB_IAA1_SHFT 13
+#define GRU_CB_IAA1_MASK 0x3
+#define GRU_CB_IMA_SHFT 1
+#define GRU_CB_IMA_MASK 0x3
+#define GRU_CB_OPC_SHFT 16
+#define GRU_CB_OPC_MASK 0xff
+#define GRU_CB_EXOPC_SHFT 24
+#define GRU_CB_EXOPC_MASK 0xff
+
+/* GRU instruction opcodes (opc field) */
+#define OP_NOP 0x00
+#define OP_BCOPY 0x01
+#define OP_VLOAD 0x02
+#define OP_IVLOAD 0x03
+#define OP_VSTORE 0x04
+#define OP_IVSTORE 0x05
+#define OP_VSET 0x06
+#define OP_IVSET 0x07
+#define OP_MESQ 0x08
+#define OP_GAMXR 0x09
+#define OP_GAMIR 0x0a
+#define OP_GAMIRR 0x0b
+#define OP_GAMER 0x0c
+#define OP_GAMERR 0x0d
+#define OP_BSTORE 0x0e
+#define OP_VFLUSH 0x0f
+
+
+/* Extended opcodes values (exopc field) */
+
+/* GAMIR - AMOs with implicit operands */
+#define EOP_IR_FETCH 0x01 /* Plain fetch of memory */
+#define EOP_IR_CLR 0x02 /* Fetch and clear */
+#define EOP_IR_INC 0x05 /* Fetch and increment */
+#define EOP_IR_DEC 0x07 /* Fetch and decrement */
+#define EOP_IR_QCHK1 0x0d /* Queue check, 64 byte msg */
+#define EOP_IR_QCHK2 0x0e /* Queue check, 128 byte msg */
+
+/* GAMIRR - Registered AMOs with implicit operands */
+#define EOP_IRR_FETCH 0x01 /* Registered fetch of memory */
+#define EOP_IRR_CLR 0x02 /* Registered fetch and clear */
+#define EOP_IRR_INC 0x05 /* Registered fetch and increment */
+#define EOP_IRR_DEC 0x07 /* Registered fetch and decrement */
+#define EOP_IRR_DECZ 0x0f /* Registered fetch and decrement, update on zero*/
+
+/* GAMER - AMOs with explicit operands */
+#define EOP_ER_SWAP 0x00 /* Exchange argument and memory */
+#define EOP_ER_OR 0x01 /* Logical OR with memory */
+#define EOP_ER_AND 0x02 /* Logical AND with memory */
+#define EOP_ER_XOR 0x03 /* Logical XOR with memory */
+#define EOP_ER_ADD 0x04 /* Add value to memory */
+#define EOP_ER_CSWAP 0x08 /* Compare with operand2, write operand1 if match*/
+#define EOP_ER_CADD 0x0c /* Queue check, operand1*64 byte msg */
+
+/* GAMERR - Registered AMOs with explicit operands */
+#define EOP_ERR_SWAP 0x00 /* Exchange argument and memory */
+#define EOP_ERR_OR 0x01 /* Logical OR with memory */
+#define EOP_ERR_AND 0x02 /* Logical AND with memory */
+#define EOP_ERR_XOR 0x03 /* Logical XOR with memory */
+#define EOP_ERR_ADD 0x04 /* Add value to memory */
+#define EOP_ERR_CSWAP 0x08 /* Compare with operand2, write operand1 if match*/
+#define EOP_ERR_EPOLL 0x09 /* Poll for equality */
+#define EOP_ERR_NPOLL 0x0a /* Poll for inequality */
+
+/* GAMXR - SGI Arithmetic unit */
+#define EOP_XR_CSWAP 0x0b /* Masked compare exchange */
+
+
+/* Transfer types (xtype field) */
+#define XTYPE_B 0x0 /* byte */
+#define XTYPE_S 0x1 /* short (2-byte) */
+#define XTYPE_W 0x2 /* word (4-byte) */
+#define XTYPE_DW 0x3 /* doubleword (8-byte) */
+#define XTYPE_CL 0x6 /* cacheline (64-byte) */
+
+
+/* Instruction access attributes (iaa0, iaa1 fields) */
+#define IAA_RAM 0x0 /* normal cached RAM access */
+#define IAA_NCRAM 0x2 /* noncoherent RAM access */
+#define IAA_MMIO 0x1 /* noncoherent memory-mapped I/O space */
+#define IAA_REGISTER 0x3 /* memory-mapped registers, etc. */
+
+
+/* Instruction mode attributes (ima field) */
+#define IMA_MAPPED 0x0 /* Virtual mode */
+#define IMA_CB_DELAY 0x1 /* hold read responses until status changes */
+#define IMA_UNMAPPED 0x2 /* bypass the TLBs (OS only) */
+#define IMA_INTERRUPT 0x4 /* Interrupt when instruction completes */
+
+/* CBE ecause bits */
+#define CBE_CAUSE_RI (1 << 0)
+#define CBE_CAUSE_INVALID_INSTRUCTION (1 << 1)
+#define CBE_CAUSE_UNMAPPED_MODE_FORBIDDEN (1 << 2)
+#define CBE_CAUSE_PE_CHECK_DATA_ERROR (1 << 3)
+#define CBE_CAUSE_IAA_GAA_MISMATCH (1 << 4)
+#define CBE_CAUSE_DATA_SEGMENT_LIMIT_EXCEPTION (1 << 5)
+#define CBE_CAUSE_OS_FATAL_TLB_FAULT (1 << 6)
+#define CBE_CAUSE_EXECUTION_HW_ERROR (1 << 7)
+#define CBE_CAUSE_TLBHW_ERROR (1 << 8)
+#define CBE_CAUSE_RA_REQUEST_TIMEOUT (1 << 9)
+#define CBE_CAUSE_HA_REQUEST_TIMEOUT (1 << 10)
+#define CBE_CAUSE_RA_RESPONSE_FATAL (1 << 11)
+#define CBE_CAUSE_RA_RESPONSE_NON_FATAL (1 << 12)
+#define CBE_CAUSE_HA_RESPONSE_FATAL (1 << 13)
+#define CBE_CAUSE_HA_RESPONSE_NON_FATAL (1 << 14)
+#define CBE_CAUSE_ADDRESS_SPACE_DECODE_ERROR (1 << 15)
+#define CBE_CAUSE_RESPONSE_DATA_ERROR (1 << 16)
+#define CBE_CAUSE_PROTOCOL_STATE_DATA_ERROR (1 << 17)
+
+/*
+ * Exceptions are retried for the following cases. If any OTHER bits are set
+ * in ecause, the exception is not retryable.
+ */
+#define EXCEPTION_RETRY_BITS (CBE_CAUSE_RESPONSE_DATA_ERROR | \
+ CBE_CAUSE_RA_REQUEST_TIMEOUT | \
+ CBE_CAUSE_TLBHW_ERROR | \
+ CBE_CAUSE_HA_REQUEST_TIMEOUT)
+
+/* Message queue head structure */
+union gru_mesqhead {
+ unsigned long val;
+ struct {
+ unsigned int head;
+ unsigned int limit;
+ };
+};
+
+
+/* Generate the low word of a GRU instruction */
+static inline unsigned int
+__opword(unsigned char opcode, unsigned char exopc, unsigned char xtype,
+ unsigned char iaa0, unsigned char iaa1,
+ unsigned char ima)
+{
+ return (1 << GRU_CB_ICMD_SHFT) |
+ (iaa0 << GRU_CB_IAA0_SHFT) |
+ (iaa1 << GRU_CB_IAA1_SHFT) |
+ (ima << GRU_CB_IMA_SHFT) |
+ (xtype << GRU_CB_XTYPE_SHFT) |
+ (opcode << GRU_CB_OPC_SHFT) |
+ (exopc << GRU_CB_EXOPC_SHFT);
+}
+
+/*
+ * Architecture specific intrinsics
+ */
+static inline void gru_flush_cache(void *p)
+{
+ __flush_cache(p);
+}
+
+/*
+ * Store the lower 32 bits of the command including the "start" bit. Then
+ * start the instruction executing.
+ */
+static inline void gru_start_instruction(struct gru_instruction *ins, int op32)
+{
+ gru_ordered_store_int(ins, op32);
+}
+
+
+/* Convert "hints" to IMA */
+#define CB_IMA(h) ((h) | IMA_UNMAPPED)
+
+/* Convert data segment cache line index into TRI0 / TRI1 value */
+#define GRU_DINDEX(i) ((i) * GRU_CACHE_LINE_BYTES)
+
+/* Inline functions for GRU instructions.
+ * Note:
+ * - nelem and stride are in elements
+ * - tri0/tri1 is in bytes for the beginning of the data segment.
+ */
+static inline void gru_vload(void *cb, unsigned long mem_addr,
+ unsigned int tri0, unsigned char xtype, unsigned long nelem,
+ unsigned long stride, unsigned long hints)
+{
+ struct gru_instruction *ins = (struct gru_instruction *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ ins->op1_stride = stride;
+ gru_start_instruction(ins, __opword(OP_VLOAD, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_vstore(void *cb, unsigned long mem_addr,
+ unsigned int tri0, unsigned char xtype, unsigned long nelem,
+ unsigned long stride, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ ins->op1_stride = stride;
+ gru_start_instruction(ins, __opword(OP_VSTORE, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_ivload(void *cb, unsigned long mem_addr,
+ unsigned int tri0, unsigned int tri1, unsigned char xtype,
+ unsigned long nelem, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ ins->tri1_bufsize = tri1;
+ gru_start_instruction(ins, __opword(OP_IVLOAD, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_ivstore(void *cb, unsigned long mem_addr,
+ unsigned int tri0, unsigned int tri1,
+ unsigned char xtype, unsigned long nelem, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ ins->tri1_bufsize = tri1;
+ gru_start_instruction(ins, __opword(OP_IVSTORE, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_vset(void *cb, unsigned long mem_addr,
+ unsigned long value, unsigned char xtype, unsigned long nelem,
+ unsigned long stride, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->op2_value_baddr1 = value;
+ ins->nelem = nelem;
+ ins->op1_stride = stride;
+ gru_start_instruction(ins, __opword(OP_VSET, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_ivset(void *cb, unsigned long mem_addr,
+ unsigned int tri1, unsigned long value, unsigned char xtype,
+ unsigned long nelem, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->op2_value_baddr1 = value;
+ ins->nelem = nelem;
+ ins->tri1_bufsize = tri1;
+ gru_start_instruction(ins, __opword(OP_IVSET, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_vflush(void *cb, unsigned long mem_addr,
+ unsigned long nelem, unsigned char xtype, unsigned long stride,
+ unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)mem_addr;
+ ins->op1_stride = stride;
+ ins->nelem = nelem;
+ gru_start_instruction(ins, __opword(OP_VFLUSH, 0, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_nop(void *cb, int hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ gru_start_instruction(ins, __opword(OP_NOP, 0, 0, 0, 0, CB_IMA(hints)));
+}
+
+
+static inline void gru_bcopy(void *cb, const unsigned long src,
+ unsigned long dest,
+ unsigned int tri0, unsigned int xtype, unsigned long nelem,
+ unsigned int bufsize, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ ins->op2_value_baddr1 = (long)dest;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ ins->tri1_bufsize = bufsize;
+ gru_start_instruction(ins, __opword(OP_BCOPY, 0, xtype, IAA_RAM,
+ IAA_RAM, CB_IMA(hints)));
+}
+
+static inline void gru_bstore(void *cb, const unsigned long src,
+ unsigned long dest, unsigned int tri0, unsigned int xtype,
+ unsigned long nelem, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ ins->op2_value_baddr1 = (long)dest;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ gru_start_instruction(ins, __opword(OP_BSTORE, 0, xtype, 0, IAA_RAM,
+ CB_IMA(hints)));
+}
+
+static inline void gru_gamir(void *cb, int exopc, unsigned long src,
+ unsigned int xtype, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ gru_start_instruction(ins, __opword(OP_GAMIR, exopc, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_gamirr(void *cb, int exopc, unsigned long src,
+ unsigned int xtype, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ gru_start_instruction(ins, __opword(OP_GAMIRR, exopc, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_gamer(void *cb, int exopc, unsigned long src,
+ unsigned int xtype,
+ unsigned long operand1, unsigned long operand2,
+ unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ ins->op1_stride = operand1;
+ ins->op2_value_baddr1 = operand2;
+ gru_start_instruction(ins, __opword(OP_GAMER, exopc, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_gamerr(void *cb, int exopc, unsigned long src,
+ unsigned int xtype, unsigned long operand1,
+ unsigned long operand2, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ ins->op1_stride = operand1;
+ ins->op2_value_baddr1 = operand2;
+ gru_start_instruction(ins, __opword(OP_GAMERR, exopc, xtype, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline void gru_gamxr(void *cb, unsigned long src,
+ unsigned int tri0, unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)src;
+ ins->nelem = 4;
+ gru_start_instruction(ins, __opword(OP_GAMXR, EOP_XR_CSWAP, XTYPE_DW,
+ IAA_RAM, 0, CB_IMA(hints)));
+}
+
+static inline void gru_mesq(void *cb, unsigned long queue,
+ unsigned long tri0, unsigned long nelem,
+ unsigned long hints)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ ins->baddr0 = (long)queue;
+ ins->nelem = nelem;
+ ins->tri0 = tri0;
+ gru_start_instruction(ins, __opword(OP_MESQ, 0, XTYPE_CL, IAA_RAM, 0,
+ CB_IMA(hints)));
+}
+
+static inline unsigned long gru_get_amo_value(void *cb)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ return ins->avalue;
+}
+
+static inline int gru_get_amo_value_head(void *cb)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ return ins->avalue & 0xffffffff;
+}
+
+static inline int gru_get_amo_value_limit(void *cb)
+{
+ struct gru_instruction *ins = (void *)cb;
+
+ return ins->avalue >> 32;
+}
+
+static inline union gru_mesqhead gru_mesq_head(int head, int limit)
+{
+ union gru_mesqhead mqh;
+
+ mqh.head = head;
+ mqh.limit = limit;
+ return mqh;
+}
+
+/*
+ * Get struct control_block_extended_exc_detail for CB.
+ */
+extern int gru_get_cb_exception_detail(void *cb,
+ struct control_block_extended_exc_detail *excdet);
+
+#define GRU_EXC_STR_SIZE 256
+
+extern int gru_check_status_proc(void *cb);
+extern int gru_wait_proc(void *cb);
+extern void gru_wait_abort_proc(void *cb);
+
+/*
+ * Control block definition for checking status
+ */
+struct gru_control_block_status {
+ unsigned int icmd :1;
+ unsigned int unused1 :31;
+ unsigned int unused2 :24;
+ unsigned int istatus :2;
+ unsigned int isubstatus :4;
+ unsigned int inused3 :2;
+};
+
+/* Get CB status */
+static inline int gru_get_cb_status(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+
+ return cbs->istatus;
+}
+
+/* Get CB message queue substatus */
+static inline int gru_get_cb_message_queue_substatus(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+
+ return cbs->isubstatus & CBSS_MSG_QUEUE_MASK;
+}
+
+/* Get CB substatus */
+static inline int gru_get_cb_substatus(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+
+ return cbs->isubstatus;
+}
+
+/* Check the status of a CB. If the CB is in UPM mode, call the
+ * OS to handle the UPM status.
+ * Returns the CB status field value (0 for normal completion)
+ */
+static inline int gru_check_status(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+ int ret = cbs->istatus;
+
+ if (ret == CBS_CALL_OS)
+ ret = gru_check_status_proc(cb);
+ return ret;
+}
+
+/* Wait for CB to complete.
+ * Returns the CB status field value (0 for normal completion)
+ */
+static inline int gru_wait(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+ int ret = cbs->istatus;;
+
+ if (ret != CBS_IDLE)
+ ret = gru_wait_proc(cb);
+ return ret;
+}
+
+/* Wait for CB to complete. Aborts program if error. (Note: error does NOT
+ * mean TLB mis - only fatal errors such as memory parity error or user
+ * bugs will cause termination.
+ */
+static inline void gru_wait_abort(void *cb)
+{
+ struct gru_control_block_status *cbs = (void *)cb;
+
+ if (cbs->istatus != CBS_IDLE)
+ gru_wait_abort_proc(cb);
+}
+
+
+/*
+ * Get a pointer to a control block
+ * gseg - GSeg address returned from gru_get_thread_gru_segment()
+ * index - index of desired CB
+ */
+static inline void *gru_get_cb_pointer(void *gseg,
+ int index)
+{
+ return gseg + GRU_CB_BASE + index * GRU_HANDLE_STRIDE;
+}
+
+/*
+ * Get a pointer to a cacheline in the data segment portion of a GSeg
+ * gseg - GSeg address returned from gru_get_thread_gru_segment()
+ * index - index of desired cache line
+ */
+static inline void *gru_get_data_pointer(void *gseg, int index)
+{
+ return gseg + GRU_DS_BASE + index * GRU_CACHE_LINE_BYTES;
+}
+
+/*
+ * Convert a vaddr into the tri index within the GSEG
+ * vaddr - virtual address of within gseg
+ */
+static inline int gru_get_tri(void *vaddr)
+{
+ return ((unsigned long)vaddr & (GRU_GSEG_PAGESIZE - 1)) - GRU_DS_BASE;
+}
+#endif /* __GRU_INSTRUCTIONS_H__ */
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * FAULT HANDLER FOR GRU DETECTED TLB MISSES
+ *
+ * This file contains code that handles TLB misses within the GRU.
+ * These misses are reported either via interrupts or user polling of
+ * the user CB.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <asm/pgtable.h>
+#include "gru.h"
+#include "grutables.h"
+#include "grulib.h"
+#include "gru_instructions.h"
+#include <asm/uv/uv_hub.h>
+
+/*
+ * Test if a physical address is a valid GRU GSEG address
+ */
+static inline int is_gru_paddr(unsigned long paddr)
+{
+ return paddr >= gru_start_paddr && paddr < gru_end_paddr;
+}
+
+/*
+ * Find the vma of a GRU segment. Caller must hold mmap_sem.
+ */
+struct vm_area_struct *gru_find_vma(unsigned long vaddr)
+{
+ struct vm_area_struct *vma;
+
+ vma = find_vma(current->mm, vaddr);
+ if (vma && vma->vm_start <= vaddr && vma->vm_ops == &gru_vm_ops)
+ return vma;
+ return NULL;
+}
+
+/*
+ * Find and lock the gts that contains the specified user vaddr.
+ *
+ * Returns:
+ * - *gts with the mmap_sem locked for read and the GTS locked.
+ * - NULL if vaddr invalid OR is not a valid GSEG vaddr.
+ */
+
+static struct gru_thread_state *gru_find_lock_gts(unsigned long vaddr)
+{
+ struct mm_struct *mm = current->mm;
+ struct vm_area_struct *vma;
+ struct gru_thread_state *gts = NULL;
+
+ down_read(&mm->mmap_sem);
+ vma = gru_find_vma(vaddr);
+ if (vma)
+ gts = gru_find_thread_state(vma, TSID(vaddr, vma));
+ if (gts)
+ mutex_lock(>s->ts_ctxlock);
+ else
+ up_read(&mm->mmap_sem);
+ return gts;
+}
+
+static struct gru_thread_state *gru_alloc_locked_gts(unsigned long vaddr)
+{
+ struct mm_struct *mm = current->mm;
+ struct vm_area_struct *vma;
+ struct gru_thread_state *gts = NULL;
+
+ down_write(&mm->mmap_sem);
+ vma = gru_find_vma(vaddr);
+ if (vma)
+ gts = gru_alloc_thread_state(vma, TSID(vaddr, vma));
+ if (gts) {
+ mutex_lock(>s->ts_ctxlock);
+ downgrade_write(&mm->mmap_sem);
+ } else {
+ up_write(&mm->mmap_sem);
+ }
+
+ return gts;
+}
+
+/*
+ * Unlock a GTS that was previously locked with gru_find_lock_gts().
+ */
+static void gru_unlock_gts(struct gru_thread_state *gts)
+{
+ mutex_unlock(>s->ts_ctxlock);
+ up_read(¤t->mm->mmap_sem);
+}
+
+/*
+ * Set a CB.istatus to active using a user virtual address. This must be done
+ * just prior to a TFH RESTART. The new cb.istatus is an in-cache status ONLY.
+ * If the line is evicted, the status may be lost. The in-cache update
+ * is necessary to prevent the user from seeing a stale cb.istatus that will
+ * change as soon as the TFH restart is complete. Races may cause an
+ * occasional failure to clear the cb.istatus, but that is ok.
+ *
+ * If the cb address is not valid (should not happen, but...), nothing
+ * bad will happen.. The get_user()/put_user() will fail but there
+ * are no bad side-effects.
+ */
+static void gru_cb_set_istatus_active(unsigned long __user *cb)
+{
+ union {
+ struct gru_instruction_bits bits;
+ unsigned long dw;
+ } u;
+
+ if (cb) {
+ get_user(u.dw, cb);
+ u.bits.istatus = CBS_ACTIVE;
+ put_user(u.dw, cb);
+ }
+}
+
+/*
+ * Convert a interrupt IRQ to a pointer to the GRU GTS that caused the
+ * interrupt. Interrupts are always sent to a cpu on the blade that contains the
+ * GRU (except for headless blades which are not currently supported). A blade
+ * has N grus; a block of N consecutive IRQs is assigned to the GRUs. The IRQ
+ * number uniquely identifies the GRU chiplet on the local blade that caused the
+ * interrupt. Always called in interrupt context.
+ */
+static inline struct gru_state *irq_to_gru(int irq)
+{
+ return &gru_base[uv_numa_blade_id()]->bs_grus[irq - IRQ_GRU];
+}
+
+/*
+ * Read & clear a TFM
+ *
+ * The GRU has an array of fault maps. A map is private to a cpu
+ * Only one cpu will be accessing a cpu's fault map.
+ *
+ * This function scans the cpu-private fault map & clears all bits that
+ * are set. The function returns a bitmap that indicates the bits that
+ * were cleared. Note that sense the maps may be updated asynchronously by
+ * the GRU, atomic operations must be used to clear bits.
+ */
+static void get_clear_fault_map(struct gru_state *gru,
+ struct gru_tlb_fault_map *map)
+{
+ unsigned long i, k;
+ struct gru_tlb_fault_map *tfm;
+
+ tfm = get_tfm_for_cpu(gru, gru_cpu_fault_map_id());
+ prefetchw(tfm); /* Helps on hardware, required for emulator */
+ for (i = 0; i < BITS_TO_LONGS(GRU_NUM_CBE); i++) {
+ k = tfm->fault_bits[i];
+ if (k)
+ k = xchg(&tfm->fault_bits[i], 0UL);
+ map->fault_bits[i] = k;
+ }
+
+ /*
+ * Not functionally required but helps performance. (Required
+ * on emulator)
+ */
+ gru_flush_cache(tfm);
+}
+
+/*
+ * Atomic (interrupt context) & non-atomic (user context) functions to
+ * convert a vaddr into a physical address. The size of the page
+ * is returned in pageshift.
+ * returns:
+ * 0 - successful
+ * < 0 - error code
+ * 1 - (atomic only) try again in non-atomic context
+ */
+static int non_atomic_pte_lookup(struct vm_area_struct *vma,
+ unsigned long vaddr, int write,
+ unsigned long *paddr, int *pageshift)
+{
+ struct page *page;
+
+ /* ZZZ Need to handle HUGE pages */
+ if (is_vm_hugetlb_page(vma))
+ return -EFAULT;
+ *pageshift = PAGE_SHIFT;
+ if (get_user_pages
+ (current, current->mm, vaddr, 1, write, 0, &page, NULL) <= 0)
+ return -EFAULT;
+ *paddr = page_to_phys(page);
+ put_page(page);
+ return 0;
+}
+
+/*
+ *
+ * atomic_pte_lookup
+ *
+ * Convert a user virtual address to a physical address
+ * Only supports Intel large pages (2MB only) on x86_64.
+ * ZZZ - hugepage support is incomplete
+ */
+static int atomic_pte_lookup(struct vm_area_struct *vma, unsigned long vaddr,
+ int write, unsigned long *paddr, int *pageshift)
+{
+ pgd_t *pgdp;
+ pmd_t *pmdp;
+ pud_t *pudp;
+ pte_t pte;
+
+ WARN_ON(irqs_disabled()); /* ZZZ debug */
+
+ local_irq_disable();
+ pgdp = pgd_offset(vma->vm_mm, vaddr);
+ if (unlikely(pgd_none(*pgdp)))
+ goto err;
+
+ pudp = pud_offset(pgdp, vaddr);
+ if (unlikely(pud_none(*pudp)))
+ goto err;
+
+ pmdp = pmd_offset(pudp, vaddr);
+ if (unlikely(pmd_none(*pmdp)))
+ goto err;
+#ifdef CONFIG_X86_64
+ if (unlikely(pmd_large(*pmdp)))
+ pte = *(pte_t *) pmdp;
+ else
+#endif
+ pte = *pte_offset_kernel(pmdp, vaddr);
+
+ local_irq_enable();
+
+ if (unlikely(!pte_present(pte) ||
+ (write && (!pte_write(pte) || !pte_dirty(pte)))))
+ return 1;
+
+ *paddr = pte_pfn(pte) << PAGE_SHIFT;
+ *pageshift = is_vm_hugetlb_page(vma) ? HPAGE_SHIFT : PAGE_SHIFT;
+ return 0;
+
+err:
+ local_irq_enable();
+ return 1;
+}
+
+/*
+ * Drop a TLB entry into the GRU. The fault is described by info in an TFH.
+ * Input:
+ * cb Address of user CBR. Null if not running in user context
+ * Return:
+ * 0 = dropin, exception, or switch to UPM successful
+ * 1 = range invalidate active
+ * < 0 = error code
+ *
+ */
+static int gru_try_dropin(struct gru_thread_state *gts,
+ struct gru_tlb_fault_handle *tfh,
+ unsigned long __user *cb)
+{
+ struct mm_struct *mm = gts->ts_mm;
+ struct vm_area_struct *vma;
+ int pageshift, asid, write, ret;
+ unsigned long paddr, gpa, vaddr;
+
+ /*
+ * NOTE: The GRU contains magic hardware that eliminates races between
+ * TLB invalidates and TLB dropins. If an invalidate occurs
+ * in the window between reading the TFH and the subsequent TLB dropin,
+ * the dropin is ignored. This eliminates the need for additional locks.
+ */
+
+ /*
+ * Error if TFH state is IDLE or FMM mode & the user issuing a UPM call.
+ * Might be a hardware race OR a stupid user. Ignore FMM because FMM
+ * is a transient state.
+ */
+ if (tfh->state == TFHSTATE_IDLE)
+ goto failidle;
+ if (tfh->state == TFHSTATE_MISS_FMM && cb)
+ goto failfmm;
+
+ write = (tfh->cause & TFHCAUSE_TLB_MOD) != 0;
+ vaddr = tfh->missvaddr;
+ asid = tfh->missasid;
+ if (asid == 0)
+ goto failnoasid;
+
+ rmb(); /* TFH must be cache resident before reading ms_range_active */
+
+ /*
+ * TFH is cache resident - at least briefly. Fail the dropin
+ * if a range invalidate is active.
+ */
+ if (atomic_read(>s->ts_gms->ms_range_active))
+ goto failactive;
+
+ vma = find_vma(mm, vaddr);
+ if (!vma)
+ goto failinval;
+
+ /*
+ * Atomic lookup is faster & usually works even if called in non-atomic
+ * context.
+ */
+ ret = atomic_pte_lookup(vma, vaddr, write, &paddr, &pageshift);
+ if (ret) {
+ if (!cb)
+ goto failupm;
+ if (non_atomic_pte_lookup(vma, vaddr, write, &paddr,
+ &pageshift))
+ goto failinval;
+ }
+ if (is_gru_paddr(paddr))
+ goto failinval;
+
+ paddr = paddr & ~((1UL << pageshift) - 1);
+ gpa = uv_soc_phys_ram_to_gpa(paddr);
+ gru_cb_set_istatus_active(cb);
+ tfh_write_restart(tfh, gpa, GAA_RAM, vaddr, asid, write,
+ GRU_PAGESIZE(pageshift));
+ STAT(tlb_dropin);
+ gru_dbg(grudev,
+ "%s: tfh 0x%p, vaddr 0x%lx, asid 0x%x, ps %d, gpa 0x%lx\n",
+ ret ? "non-atomic" : "atomic", tfh, vaddr, asid,
+ pageshift, gpa);
+ return 0;
+
+failnoasid:
+ /* No asid (delayed unload). */
+ STAT(tlb_dropin_fail_no_asid);
+ gru_dbg(grudev, "FAILED no_asid tfh: 0x%p, vaddr 0x%lx\n", tfh, vaddr);
+ if (!cb)
+ tfh_user_polling_mode(tfh);
+ else
+ gru_flush_cache(tfh);
+ return -EAGAIN;
+
+failupm:
+ /* Atomic failure switch CBR to UPM */
+ tfh_user_polling_mode(tfh);
+ STAT(tlb_dropin_fail_upm);
+ gru_dbg(grudev, "FAILED upm tfh: 0x%p, vaddr 0x%lx\n", tfh, vaddr);
+ return 1;
+
+failfmm:
+ /* FMM state on UPM call */
+ STAT(tlb_dropin_fail_fmm);
+ gru_dbg(grudev, "FAILED fmm tfh: 0x%p, state %d\n", tfh, tfh->state);
+ return 0;
+
+failidle:
+ /* TFH was idle - no miss pending */
+ gru_flush_cache(tfh);
+ if (cb)
+ gru_flush_cache(cb);
+ STAT(tlb_dropin_fail_idle);
+ gru_dbg(grudev, "FAILED idle tfh: 0x%p, state %d\n", tfh, tfh->state);
+ return 0;
+
+failinval:
+ /* All errors (atomic & non-atomic) switch CBR to EXCEPTION state */
+ tfh_exception(tfh);
+ STAT(tlb_dropin_fail_invalid);
+ gru_dbg(grudev, "FAILED inval tfh: 0x%p, vaddr 0x%lx\n", tfh, vaddr);
+ return -EFAULT;
+
+failactive:
+ /* Range invalidate active. Switch to UPM iff atomic */
+ if (!cb)
+ tfh_user_polling_mode(tfh);
+ else
+ gru_flush_cache(tfh);
+ STAT(tlb_dropin_fail_range_active);
+ gru_dbg(grudev, "FAILED range active: tfh 0x%p, vaddr 0x%lx\n",
+ tfh, vaddr);
+ return 1;
+}
+
+/*
+ * Process an external interrupt from the GRU. This interrupt is
+ * caused by a TLB miss.
+ * Note that this is the interrupt handler that is registered with linux
+ * interrupt handlers.
+ */
+irqreturn_t gru_intr(int irq, void *dev_id)
+{
+ struct gru_state *gru;
+ struct gru_tlb_fault_map map;
+ struct gru_thread_state *gts;
+ struct gru_tlb_fault_handle *tfh = NULL;
+ int cbrnum, ctxnum;
+
+ STAT(intr);
+
+ gru = irq_to_gru(irq);
+ if (!gru) {
+ dev_err(grudev, "GRU: invalid interrupt: cpu %d, irq %d\n",
+ raw_smp_processor_id(), irq);
+ return IRQ_NONE;
+ }
+ get_clear_fault_map(gru, &map);
+ gru_dbg(grudev, "irq %d, gru %x, map 0x%lx\n", irq, gru->gs_gid,
+ map.fault_bits[0]);
+
+ for_each_cbr_in_tfm(cbrnum, map.fault_bits) {
+ tfh = get_tfh_by_index(gru, cbrnum);
+ prefetchw(tfh); /* Helps on hdw, required for emulator */
+
+ /*
+ * When hardware sets a bit in the faultmap, it implicitly
+ * locks the GRU context so that it cannot be unloaded.
+ * The gts cannot change until a TFH start/writestart command
+ * is issued.
+ */
+ ctxnum = tfh->ctxnum;
+ gts = gru->gs_gts[ctxnum];
+
+ /*
+ * This is running in interrupt context. Trylock the mmap_sem.
+ * If it fails, retry the fault in user context.
+ */
+ if (down_read_trylock(>s->ts_mm->mmap_sem)) {
+ gru_try_dropin(gts, tfh, NULL);
+ up_read(>s->ts_mm->mmap_sem);
+ } else {
+ tfh_user_polling_mode(tfh);
+ }
+ }
+ return IRQ_HANDLED;
+}
+
+
+static int gru_user_dropin(struct gru_thread_state *gts,
+ struct gru_tlb_fault_handle *tfh,
+ unsigned long __user *cb)
+{
+ struct gru_mm_struct *gms = gts->ts_gms;
+ int ret;
+
+ while (1) {
+ wait_event(gms->ms_wait_queue,
+ atomic_read(&gms->ms_range_active) == 0);
+ prefetchw(tfh); /* Helps on hdw, required for emulator */
+ ret = gru_try_dropin(gts, tfh, cb);
+ if (ret <= 0)
+ return ret;
+ STAT(call_os_wait_queue);
+ }
+}
+
+/*
+ * This interface is called as a result of a user detecting a "call OS" bit
+ * in a user CB. Normally means that a TLB fault has occurred.
+ * cb - user virtual address of the CB
+ */
+int gru_handle_user_call_os(unsigned long cb)
+{
+ struct gru_tlb_fault_handle *tfh;
+ struct gru_thread_state *gts;
+ unsigned long __user *cbp;
+ int ucbnum, cbrnum, ret = -EINVAL;
+
+ STAT(call_os);
+ gru_dbg(grudev, "address 0x%lx\n", cb);
+
+ /* sanity check the cb pointer */
+ ucbnum = get_cb_number((void *)cb);
+ if ((cb & (GRU_HANDLE_STRIDE - 1)) || ucbnum >= GRU_NUM_CB)
+ return -EINVAL;
+ cbp = (unsigned long *)cb;
+
+ gts = gru_find_lock_gts(cb);
+ if (!gts)
+ return -EINVAL;
+
+ if (ucbnum >= gts->ts_cbr_au_count * GRU_CBR_AU_SIZE) {
+ ret = -EINVAL;
+ goto exit;
+ }
+
+ /*
+ * If force_unload is set, the UPM TLB fault is phony. The task
+ * has migrated to another node and the GSEG must be moved. Just
+ * unload the context. The task will page fault and assign a new
+ * context.
+ */
+ ret = -EAGAIN;
+ cbrnum = thread_cbr_number(gts, ucbnum);
+ if (gts->ts_force_unload) {
+ gru_unload_context(gts, 1);
+ } else if (gts->ts_gru) {
+ tfh = get_tfh_by_index(gts->ts_gru, cbrnum);
+ ret = gru_user_dropin(gts, tfh, cbp);
+ }
+exit:
+ gru_unlock_gts(gts);
+ return ret;
+}
+
+/*
+ * Fetch the exception detail information for a CB that terminated with
+ * an exception.
+ */
+int gru_get_exception_detail(unsigned long arg)
+{
+ struct control_block_extended_exc_detail excdet;
+ struct gru_control_block_extended *cbe;
+ struct gru_thread_state *gts;
+ int ucbnum, cbrnum, ret;
+
+ STAT(user_exception);
+ if (copy_from_user(&excdet, (void __user *)arg, sizeof(excdet)))
+ return -EFAULT;
+
+ gru_dbg(grudev, "address 0x%lx\n", excdet.cb);
+ gts = gru_find_lock_gts(excdet.cb);
+ if (!gts)
+ return -EINVAL;
+
+ if (gts->ts_gru) {
+ ucbnum = get_cb_number((void *)excdet.cb);
+ cbrnum = thread_cbr_number(gts, ucbnum);
+ cbe = get_cbe_by_index(gts->ts_gru, cbrnum);
+ excdet.opc = cbe->opccpy;
+ excdet.exopc = cbe->exopccpy;
+ excdet.ecause = cbe->ecause;
+ excdet.exceptdet0 = cbe->idef1upd;
+ excdet.exceptdet1 = cbe->idef3upd;
+ ret = 0;
+ } else {
+ ret = -EAGAIN;
+ }
+ gru_unlock_gts(gts);
+
+ gru_dbg(grudev, "address 0x%lx, ecause 0x%x\n", excdet.cb,
+ excdet.ecause);
+ if (!ret && copy_to_user((void __user *)arg, &excdet, sizeof(excdet)))
+ ret = -EFAULT;
+ return ret;
+}
+
+/*
+ * User request to unload a context. Content is saved for possible reload.
+ */
+int gru_user_unload_context(unsigned long arg)
+{
+ struct gru_thread_state *gts;
+ struct gru_unload_context_req req;
+
+ STAT(user_unload_context);
+ if (copy_from_user(&req, (void __user *)arg, sizeof(req)))
+ return -EFAULT;
+
+ gru_dbg(grudev, "gseg 0x%lx\n", req.gseg);
+
+ gts = gru_find_lock_gts(req.gseg);
+ if (!gts)
+ return -EINVAL;
+
+ if (gts->ts_gru)
+ gru_unload_context(gts, 1);
+ gru_unlock_gts(gts);
+
+ return 0;
+}
+
+/*
+ * User request to flush a range of virtual addresses from the GRU TLB
+ * (Mainly for testing).
+ */
+int gru_user_flush_tlb(unsigned long arg)
+{
+ struct gru_thread_state *gts;
+ struct gru_flush_tlb_req req;
+
+ STAT(user_flush_tlb);
+ if (copy_from_user(&req, (void __user *)arg, sizeof(req)))
+ return -EFAULT;
+
+ gru_dbg(grudev, "gseg 0x%lx, vaddr 0x%lx, len 0x%lx\n", req.gseg,
+ req.vaddr, req.len);
+
+ gts = gru_find_lock_gts(req.gseg);
+ if (!gts)
+ return -EINVAL;
+
+ gru_flush_tlb_range(gts->ts_gms, req.vaddr, req.vaddr + req.len);
+ gru_unlock_gts(gts);
+
+ return 0;
+}
+
+/*
+ * Register the current task as the user of the GSEG slice.
+ * Needed for TLB fault interrupt targeting.
+ */
+int gru_set_task_slice(long address)
+{
+ struct gru_thread_state *gts;
+
+ STAT(set_task_slice);
+ gru_dbg(grudev, "address 0x%lx\n", address);
+ gts = gru_alloc_locked_gts(address);
+ if (!gts)
+ return -EINVAL;
+
+ gts->ts_tgid_owner = current->tgid;
+ gru_unlock_gts(gts);
+
+ return 0;
+}
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * FILE OPERATIONS & DRIVER INITIALIZATION
+ *
+ * This file supports the user system call for file open, close, mmap, etc.
+ * This also incudes the driver initialization code.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/io.h>
+#include <linux/smp_lock.h>
+#include <linux/spinlock.h>
+#include <linux/device.h>
+#include <linux/miscdevice.h>
+#include <linux/interrupt.h>
+#include <linux/proc_fs.h>
+#include <linux/uaccess.h>
+#include "gru.h"
+#include "grulib.h"
+#include "grutables.h"
+
+#if defined CONFIG_X86_64
+#include <asm/genapic.h>
+#include <asm/irq.h>
+#define IS_UV() is_uv_system()
+#elif defined CONFIG_IA64
+#include <asm/system.h>
+#include <asm/sn/simulator.h>
+/* temp support for running on hardware simulator */
+#define IS_UV() IS_MEDUSA() || ia64_platform_is("uv")
+#else
+#define IS_UV() 0
+#endif
+
+#include <asm/uv/uv_hub.h>
+#include <asm/uv/uv_mmrs.h>
+
+struct gru_blade_state *gru_base[GRU_MAX_BLADES] __read_mostly;
+unsigned long gru_start_paddr, gru_end_paddr __read_mostly;
+struct gru_stats_s gru_stats;
+
+/* Guaranteed user available resources on each node */
+static int max_user_cbrs, max_user_dsr_bytes;
+
+static struct file_operations gru_fops;
+static struct miscdevice gru_miscdev;
+
+
+/*
+ * gru_vma_close
+ *
+ * Called when unmapping a device mapping. Frees all gru resources
+ * and tables belonging to the vma.
+ */
+static void gru_vma_close(struct vm_area_struct *vma)
+{
+ struct gru_vma_data *vdata;
+ struct gru_thread_state *gts;
+ struct list_head *entry, *next;
+
+ if (!vma->vm_private_data)
+ return;
+
+ vdata = vma->vm_private_data;
+ vma->vm_private_data = NULL;
+ gru_dbg(grudev, "vma %p, file %p, vdata %p\n", vma, vma->vm_file,
+ vdata);
+ list_for_each_safe(entry, next, &vdata->vd_head) {
+ gts =
+ list_entry(entry, struct gru_thread_state, ts_next);
+ list_del(>s->ts_next);
+ mutex_lock(>s->ts_ctxlock);
+ if (gts->ts_gru)
+ gru_unload_context(gts, 0);
+ mutex_unlock(>s->ts_ctxlock);
+ gts_drop(gts);
+ }
+ kfree(vdata);
+ STAT(vdata_free);
+}
+
+/*
+ * gru_file_mmap
+ *
+ * Called when mmaping the device. Initializes the vma with a fault handler
+ * and private data structure necessary to allocate, track, and free the
+ * underlying pages.
+ */
+static int gru_file_mmap(struct file *file, struct vm_area_struct *vma)
+{
+ if ((vma->vm_flags & (VM_SHARED | VM_WRITE)) != (VM_SHARED | VM_WRITE))
+ return -EPERM;
+
+ if (vma->vm_start & (GRU_GSEG_PAGESIZE - 1) ||
+ vma->vm_end & (GRU_GSEG_PAGESIZE - 1))
+ return -EINVAL;
+
+ vma->vm_flags |=
+ (VM_IO | VM_DONTCOPY | VM_LOCKED | VM_DONTEXPAND | VM_PFNMAP |
+ VM_RESERVED);
+ vma->vm_page_prot = PAGE_SHARED;
+ vma->vm_ops = &gru_vm_ops;
+
+ vma->vm_private_data = gru_alloc_vma_data(vma, 0);
+ if (!vma->vm_private_data)
+ return -ENOMEM;
+
+ gru_dbg(grudev, "file %p, vaddr 0x%lx, vma %p, vdata %p\n",
+ file, vma->vm_start, vma, vma->vm_private_data);
+ return 0;
+}
+
+/*
+ * Create a new GRU context
+ */
+static int gru_create_new_context(unsigned long arg)
+{
+ struct gru_create_context_req req;
+ struct vm_area_struct *vma;
+ struct gru_vma_data *vdata;
+ int ret = -EINVAL;
+
+
+ if (copy_from_user(&req, (void __user *)arg, sizeof(req)))
+ return -EFAULT;
+
+ if (req.data_segment_bytes == 0 ||
+ req.data_segment_bytes > max_user_dsr_bytes)
+ return -EINVAL;
+ if (!req.control_blocks || !req.maximum_thread_count ||
+ req.control_blocks > max_user_cbrs)
+ return -EINVAL;
+
+ if (!(req.options & GRU_OPT_MISS_MASK))
+ req.options |= GRU_OPT_MISS_FMM_INTR;
+
+ down_write(¤t->mm->mmap_sem);
+ vma = gru_find_vma(req.gseg);
+ if (vma) {
+ vdata = vma->vm_private_data;
+ vdata->vd_user_options = req.options;
+ vdata->vd_dsr_au_count =
+ GRU_DS_BYTES_TO_AU(req.data_segment_bytes);
+ vdata->vd_cbr_au_count = GRU_CB_COUNT_TO_AU(req.control_blocks);
+ ret = 0;
+ }
+ up_write(¤t->mm->mmap_sem);
+
+ return ret;
+}
+
+/*
+ * Get GRU configuration info (temp - for emulator testing)
+ */
+static long gru_get_config_info(unsigned long arg)
+{
+ struct gru_config_info info;
+ int nodesperblade;
+
+ if (num_online_nodes() > 1 &&
+ (uv_node_to_blade_id(1) == uv_node_to_blade_id(0)))
+ nodesperblade = 2;
+ else
+ nodesperblade = 1;
+ info.cpus = num_online_cpus();
+ info.nodes = num_online_nodes();
+ info.blades = info.nodes / nodesperblade;
+ info.chiplets = GRU_CHIPLETS_PER_BLADE * info.blades;
+
+ if (copy_to_user((void __user *)arg, &info, sizeof(info)))
+ return -EFAULT;
+ return 0;
+}
+
+/*
+ * Get GRU chiplet status
+ */
+static long gru_get_chiplet_status(unsigned long arg)
+{
+ struct gru_state *gru;
+ struct gru_chiplet_info info;
+
+ if (copy_from_user(&info, (void __user *)arg, sizeof(info)))
+ return -EFAULT;
+
+ if (info.node == -1)
+ info.node = numa_node_id();
+ if (info.node >= num_possible_nodes() ||
+ info.chiplet >= GRU_CHIPLETS_PER_HUB ||
+ info.node < 0 || info.chiplet < 0)
+ return -EINVAL;
+
+ info.blade = uv_node_to_blade_id(info.node);
+ gru = get_gru(info.blade, info.chiplet);
+
+ info.total_dsr_bytes = GRU_NUM_DSR_BYTES;
+ info.total_cbr = GRU_NUM_CB;
+ info.total_user_dsr_bytes = GRU_NUM_DSR_BYTES -
+ gru->gs_reserved_dsr_bytes;
+ info.total_user_cbr = GRU_NUM_CB - gru->gs_reserved_cbrs;
+ info.free_user_dsr_bytes = hweight64(gru->gs_dsr_map) *
+ GRU_DSR_AU_BYTES;
+ info.free_user_cbr = hweight64(gru->gs_cbr_map) * GRU_CBR_AU_SIZE;
+
+ if (copy_to_user((void __user *)arg, &info, sizeof(info)))
+ return -EFAULT;
+ return 0;
+}
+
+/*
+ * gru_file_unlocked_ioctl
+ *
+ * Called to update file attributes via IOCTL calls.
+ */
+static long gru_file_unlocked_ioctl(struct file *file, unsigned int req,
+ unsigned long arg)
+{
+ int err = -EBADRQC;
+
+ gru_dbg(grudev, "file %p\n", file);
+
+ switch (req) {
+ case GRU_CREATE_CONTEXT:
+ err = gru_create_new_context(arg);
+ break;
+ case GRU_SET_TASK_SLICE:
+ err = gru_set_task_slice(arg);
+ break;
+ case GRU_USER_GET_EXCEPTION_DETAIL:
+ err = gru_get_exception_detail(arg);
+ break;
+ case GRU_USER_UNLOAD_CONTEXT:
+ err = gru_user_unload_context(arg);
+ break;
+ case GRU_GET_CHIPLET_STATUS:
+ err = gru_get_chiplet_status(arg);
+ break;
+ case GRU_USER_FLUSH_TLB:
+ err = gru_user_flush_tlb(arg);
+ break;
+ case GRU_USER_CALL_OS:
+ err = gru_handle_user_call_os(arg);
+ break;
+ case GRU_GET_CONFIG_INFO:
+ err = gru_get_config_info(arg);
+ break;
+ }
+ return err;
+}
+
+/*
+ * Called at init time to build tables for all GRUs that are present in the
+ * system.
+ */
+static void gru_init_chiplet(struct gru_state *gru, unsigned long paddr,
+ void *vaddr, int nid, int bid, int grunum)
+{
+ spin_lock_init(&gru->gs_lock);
+ spin_lock_init(&gru->gs_asid_lock);
+ gru->gs_gru_base_paddr = paddr;
+ gru->gs_gru_base_vaddr = vaddr;
+ gru->gs_gid = bid * GRU_CHIPLETS_PER_BLADE + grunum;
+ gru->gs_blade = gru_base[bid];
+ gru->gs_blade_id = bid;
+ gru->gs_cbr_map = (GRU_CBR_AU == 64) ? ~0 : (1UL << GRU_CBR_AU) - 1;
+ gru->gs_dsr_map = (1UL << GRU_DSR_AU) - 1;
+ gru_tgh_flush_init(gru);
+ gru_dbg(grudev, "bid %d, nid %d, gru %x, vaddr %p (0x%lx)\n",
+ bid, nid, gru->gs_gid, gru->gs_gru_base_vaddr,
+ gru->gs_gru_base_paddr);
+ gru_kservices_init(gru);
+}
+
+static int gru_init_tables(unsigned long gru_base_paddr, void *gru_base_vaddr)
+{
+ int pnode, nid, bid, chip;
+ int cbrs, dsrbytes, n;
+ int order = get_order(sizeof(struct gru_blade_state));
+ struct page *page;
+ struct gru_state *gru;
+ unsigned long paddr;
+ void *vaddr;
+
+ max_user_cbrs = GRU_NUM_CB;
+ max_user_dsr_bytes = GRU_NUM_DSR_BYTES;
+ for_each_online_node(nid) {
+ bid = uv_node_to_blade_id(nid);
+ pnode = uv_node_to_pnode(nid);
+ if (gru_base[bid])
+ continue;
+ page = alloc_pages_node(nid, GFP_KERNEL, order);
+ if (!page)
+ goto fail;
+ gru_base[bid] = page_address(page);
+ memset(gru_base[bid], 0, sizeof(struct gru_blade_state));
+ gru_base[bid]->bs_lru_gru = &gru_base[bid]->bs_grus[0];
+ spin_lock_init(&gru_base[bid]->bs_lock);
+
+ dsrbytes = 0;
+ cbrs = 0;
+ for (gru = gru_base[bid]->bs_grus, chip = 0;
+ chip < GRU_CHIPLETS_PER_BLADE;
+ chip++, gru++) {
+ paddr = gru_chiplet_paddr(gru_base_paddr, pnode, chip);
+ vaddr = gru_chiplet_vaddr(gru_base_vaddr, pnode, chip);
+ gru_init_chiplet(gru, paddr, vaddr, bid, nid, chip);
+ n = hweight64(gru->gs_cbr_map) * GRU_CBR_AU_SIZE;
+ cbrs = max(cbrs, n);
+ n = hweight64(gru->gs_dsr_map) * GRU_DSR_AU_BYTES;
+ dsrbytes = max(dsrbytes, n);
+ }
+ max_user_cbrs = min(max_user_cbrs, cbrs);
+ max_user_dsr_bytes = min(max_user_dsr_bytes, dsrbytes);
+ }
+
+ return 0;
+
+fail:
+ for (nid--; nid >= 0; nid--)
+ free_pages((unsigned long)gru_base[nid], order);
+ return -ENOMEM;
+}
+
+#ifdef CONFIG_IA64
+
+static int get_base_irq(void)
+{
+ return IRQ_GRU;
+}
+
+#elif defined CONFIG_X86_64
+
+static void noop(unsigned int irq)
+{
+}
+
+static struct irq_chip gru_chip = {
+ .name = "gru",
+ .mask = noop,
+ .unmask = noop,
+ .ack = noop,
+};
+
+static int get_base_irq(void)
+{
+ set_irq_chip(IRQ_GRU, &gru_chip);
+ set_irq_chip(IRQ_GRU + 1, &gru_chip);
+ return IRQ_GRU;
+}
+#endif
+
+/*
+ * gru_init
+ *
+ * Called at boot or module load time to initialize the GRUs.
+ */
+static int __init gru_init(void)
+{
+ int ret, irq, chip;
+ char id[10];
+ void *gru_start_vaddr;
+
+ if (!IS_UV())
+ return 0;
+
+#if defined CONFIG_IA64
+ gru_start_paddr = 0xd000000000UL; /* ZZZZZZZZZZZZZZZZZZZ fixme */
+#else
+ gru_start_paddr = uv_read_local_mmr(UVH_RH_GAM_GRU_OVERLAY_CONFIG_MMR) &
+ 0x7fffffffffffUL;
+
+#endif
+ gru_start_vaddr = __va(gru_start_paddr);
+ gru_end_paddr = gru_start_paddr + MAX_NUMNODES * GRU_SIZE;
+ printk(KERN_INFO "GRU space: 0x%lx - 0x%lx\n",
+ gru_start_paddr, gru_end_paddr);
+ irq = get_base_irq();
+ for (chip = 0; chip < GRU_CHIPLETS_PER_BLADE; chip++) {
+ ret = request_irq(irq + chip, gru_intr, 0, id, NULL);
+ if (ret) {
+ printk(KERN_ERR "%s: request_irq failed\n",
+ GRU_DRIVER_ID_STR);
+ goto exit1;
+ }
+ }
+
+ ret = misc_register(&gru_miscdev);
+ if (ret) {
+ printk(KERN_ERR "%s: misc_register failed\n",
+ GRU_DRIVER_ID_STR);
+ goto exit1;
+ }
+
+ ret = gru_proc_init();
+ if (ret) {
+ printk(KERN_ERR "%s: proc init failed\n", GRU_DRIVER_ID_STR);
+ goto exit2;
+ }
+
+ ret = gru_init_tables(gru_start_paddr, gru_start_vaddr);
+ if (ret) {
+ printk(KERN_ERR "%s: init tables failed\n", GRU_DRIVER_ID_STR);
+ goto exit3;
+ }
+
+ printk(KERN_INFO "%s: v%s\n", GRU_DRIVER_ID_STR,
+ GRU_DRIVER_VERSION_STR);
+ return 0;
+
+exit3:
+ gru_proc_exit();
+exit2:
+ misc_deregister(&gru_miscdev);
+exit1:
+ for (--chip; chip >= 0; chip--)
+ free_irq(irq + chip, NULL);
+ return ret;
+
+}
+
+static void __exit gru_exit(void)
+{
+ int i, bid;
+ int order = get_order(sizeof(struct gru_state) *
+ GRU_CHIPLETS_PER_BLADE);
+
+ for (i = 0; i < GRU_CHIPLETS_PER_BLADE; i++)
+ free_irq(IRQ_GRU + i, NULL);
+
+ for (bid = 0; bid < GRU_MAX_BLADES; bid++)
+ free_pages((unsigned long)gru_base[bid], order);
+
+ misc_deregister(&gru_miscdev);
+ gru_proc_exit();
+}
+
+static struct file_operations gru_fops = {
+ .owner = THIS_MODULE,
+ .unlocked_ioctl = gru_file_unlocked_ioctl,
+ .mmap = gru_file_mmap,
+};
+
+static struct miscdevice gru_miscdev = {
+ .minor = MISC_DYNAMIC_MINOR,
+ .name = "gru",
+ .fops = &gru_fops,
+};
+
+struct vm_operations_struct gru_vm_ops = {
+ .close = gru_vma_close,
+ .fault = gru_fault,
+};
+
+module_init(gru_init);
+module_exit(gru_exit);
+
+module_param(gru_options, ulong, 0644);
+MODULE_PARM_DESC(gru_options, "Various debug options");
+
+MODULE_AUTHOR("Silicon Graphics, Inc.");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION(GRU_DRIVER_ID_STR GRU_DRIVER_VERSION_STR);
+MODULE_VERSION(GRU_DRIVER_VERSION_STR);
+
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * GRU HANDLE DEFINITION
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __GRUHANDLES_H__
+#define __GRUHANDLES_H__
+#include "gru_instructions.h"
+
+/*
+ * Manifest constants for GRU Memory Map
+ */
+#define GRU_GSEG0_BASE 0
+#define GRU_MCS_BASE (64 * 1024 * 1024)
+#define GRU_SIZE (128UL * 1024 * 1024)
+
+/* Handle & resource counts */
+#define GRU_NUM_CB 128
+#define GRU_NUM_DSR_BYTES (32 * 1024)
+#define GRU_NUM_TFM 16
+#define GRU_NUM_TGH 24
+#define GRU_NUM_CBE 128
+#define GRU_NUM_TFH 128
+#define GRU_NUM_CCH 16
+#define GRU_NUM_GSH 1
+
+/* Maximum resource counts that can be reserved by user programs */
+#define GRU_NUM_USER_CBR GRU_NUM_CBE
+#define GRU_NUM_USER_DSR_BYTES GRU_NUM_DSR_BYTES
+
+/* Bytes per handle & handle stride. Code assumes all cb, tfh, cbe handles
+ * are the same */
+#define GRU_HANDLE_BYTES 64
+#define GRU_HANDLE_STRIDE 256
+
+/* Base addresses of handles */
+#define GRU_TFM_BASE (GRU_MCS_BASE + 0x00000)
+#define GRU_TGH_BASE (GRU_MCS_BASE + 0x08000)
+#define GRU_CBE_BASE (GRU_MCS_BASE + 0x10000)
+#define GRU_TFH_BASE (GRU_MCS_BASE + 0x18000)
+#define GRU_CCH_BASE (GRU_MCS_BASE + 0x20000)
+#define GRU_GSH_BASE (GRU_MCS_BASE + 0x30000)
+
+/* User gseg constants */
+#define GRU_GSEG_STRIDE (4 * 1024 * 1024)
+#define GSEG_BASE(a) ((a) & ~(GRU_GSEG_PAGESIZE - 1))
+
+/* Data segment constants */
+#define GRU_DSR_AU_BYTES 1024
+#define GRU_DSR_CL (GRU_NUM_DSR_BYTES / GRU_CACHE_LINE_BYTES)
+#define GRU_DSR_AU_CL (GRU_DSR_AU_BYTES / GRU_CACHE_LINE_BYTES)
+#define GRU_DSR_AU (GRU_NUM_DSR_BYTES / GRU_DSR_AU_BYTES)
+
+/* Control block constants */
+#define GRU_CBR_AU_SIZE 2
+#define GRU_CBR_AU (GRU_NUM_CBE / GRU_CBR_AU_SIZE)
+
+/* Convert resource counts to the number of AU */
+#define GRU_DS_BYTES_TO_AU(n) DIV_ROUND_UP(n, GRU_DSR_AU_BYTES)
+#define GRU_CB_COUNT_TO_AU(n) DIV_ROUND_UP(n, GRU_CBR_AU_SIZE)
+
+/* UV limits */
+#define GRU_CHIPLETS_PER_HUB 2
+#define GRU_HUBS_PER_BLADE 1
+#define GRU_CHIPLETS_PER_BLADE (GRU_HUBS_PER_BLADE * GRU_CHIPLETS_PER_HUB)
+
+/* User GRU Gseg offsets */
+#define GRU_CB_BASE 0
+#define GRU_CB_LIMIT (GRU_CB_BASE + GRU_HANDLE_STRIDE * GRU_NUM_CBE)
+#define GRU_DS_BASE 0x20000
+#define GRU_DS_LIMIT (GRU_DS_BASE + GRU_NUM_DSR_BYTES)
+
+/* Convert a GRU physical address to the chiplet offset */
+#define GSEGPOFF(h) ((h) & (GRU_SIZE - 1))
+
+/* Convert an arbitrary handle address to the beginning of the GRU segment */
+#ifndef __PLUGIN__
+#define GRUBASE(h) ((void *)((unsigned long)(h) & ~(GRU_SIZE - 1)))
+#else
+extern void *gmu_grubase(void *h);
+#define GRUBASE(h) gmu_grubase(h)
+#endif
+
+/* General addressing macros. */
+static inline void *get_gseg_base_address(void *base, int ctxnum)
+{
+ return (void *)(base + GRU_GSEG0_BASE + GRU_GSEG_STRIDE * ctxnum);
+}
+
+static inline void *get_gseg_base_address_cb(void *base, int ctxnum, int line)
+{
+ return (void *)(get_gseg_base_address(base, ctxnum) +
+ GRU_CB_BASE + GRU_HANDLE_STRIDE * line);
+}
+
+static inline void *get_gseg_base_address_ds(void *base, int ctxnum, int line)
+{
+ return (void *)(get_gseg_base_address(base, ctxnum) + GRU_DS_BASE +
+ GRU_CACHE_LINE_BYTES * line);
+}
+
+static inline struct gru_tlb_fault_map *get_tfm(void *base, int ctxnum)
+{
+ return (struct gru_tlb_fault_map *)(base + GRU_TFM_BASE +
+ ctxnum * GRU_HANDLE_STRIDE);
+}
+
+static inline struct gru_tlb_global_handle *get_tgh(void *base, int ctxnum)
+{
+ return (struct gru_tlb_global_handle *)(base + GRU_TGH_BASE +
+ ctxnum * GRU_HANDLE_STRIDE);
+}
+
+static inline struct gru_control_block_extended *get_cbe(void *base, int ctxnum)
+{
+ return (struct gru_control_block_extended *)(base + GRU_CBE_BASE +
+ ctxnum * GRU_HANDLE_STRIDE);
+}
+
+static inline struct gru_tlb_fault_handle *get_tfh(void *base, int ctxnum)
+{
+ return (struct gru_tlb_fault_handle *)(base + GRU_TFH_BASE +
+ ctxnum * GRU_HANDLE_STRIDE);
+}
+
+static inline struct gru_context_configuration_handle *get_cch(void *base,
+ int ctxnum)
+{
+ return (struct gru_context_configuration_handle *)(base +
+ GRU_CCH_BASE + ctxnum * GRU_HANDLE_STRIDE);
+}
+
+static inline unsigned long get_cb_number(void *cb)
+{
+ return (((unsigned long)cb - GRU_CB_BASE) % GRU_GSEG_PAGESIZE) /
+ GRU_HANDLE_STRIDE;
+}
+
+/* byte offset to a specific GRU chiplet. (p=pnode, c=chiplet (0 or 1)*/
+static inline unsigned long gru_chiplet_paddr(unsigned long paddr, int pnode,
+ int chiplet)
+{
+ return paddr + GRU_SIZE * (2 * pnode + chiplet);
+}
+
+static inline void *gru_chiplet_vaddr(void *vaddr, int pnode, int chiplet)
+{
+ return vaddr + GRU_SIZE * (2 * pnode + chiplet);
+}
+
+
+
+/*
+ * Global TLB Fault Map
+ * Bitmap of outstanding TLB misses needing interrupt/polling service.
+ *
+ */
+struct gru_tlb_fault_map {
+ unsigned long fault_bits[BITS_TO_LONGS(GRU_NUM_CBE)];
+ unsigned long fill0[2];
+ unsigned long done_bits[BITS_TO_LONGS(GRU_NUM_CBE)];
+ unsigned long fill1[2];
+};
+
+/*
+ * TGH - TLB Global Handle
+ * Used for TLB flushing.
+ *
+ */
+struct gru_tlb_global_handle {
+ unsigned int cmd:1; /* DW 0 */
+ unsigned int delresp:1;
+ unsigned int opc:1;
+ unsigned int fill1:5;
+
+ unsigned int fill2:8;
+
+ unsigned int status:2;
+ unsigned long fill3:2;
+ unsigned int state:3;
+ unsigned long fill4:1;
+
+ unsigned int cause:3;
+ unsigned long fill5:37;
+
+ unsigned long vaddr:64; /* DW 1 */
+
+ unsigned int asid:24; /* DW 2 */
+ unsigned int fill6:8;
+
+ unsigned int pagesize:5;
+ unsigned int fill7:11;
+
+ unsigned int global:1;
+ unsigned int fill8:15;
+
+ unsigned long vaddrmask:39; /* DW 3 */
+ unsigned int fill9:9;
+ unsigned int n:10;
+ unsigned int fill10:6;
+
+ unsigned int ctxbitmap:16; /* DW4 */
+ unsigned long fill11[3];
+};
+
+enum gru_tgh_cmd {
+ TGHCMD_START
+};
+
+enum gru_tgh_opc {
+ TGHOP_TLBNOP,
+ TGHOP_TLBINV
+};
+
+enum gru_tgh_status {
+ TGHSTATUS_IDLE,
+ TGHSTATUS_EXCEPTION,
+ TGHSTATUS_ACTIVE
+};
+
+enum gru_tgh_state {
+ TGHSTATE_IDLE,
+ TGHSTATE_PE_INVAL,
+ TGHSTATE_INTERRUPT_INVAL,
+ TGHSTATE_WAITDONE,
+ TGHSTATE_RESTART_CTX,
+};
+
+/*
+ * TFH - TLB Global Handle
+ * Used for TLB dropins into the GRU TLB.
+ *
+ */
+struct gru_tlb_fault_handle {
+ unsigned int cmd:1; /* DW 0 - low 32*/
+ unsigned int delresp:1;
+ unsigned int fill0:2;
+ unsigned int opc:3;
+ unsigned int fill1:9;
+
+ unsigned int status:2;
+ unsigned int fill2:1;
+ unsigned int color:1;
+ unsigned int state:3;
+ unsigned int fill3:1;
+
+ unsigned int cause:7; /* DW 0 - high 32 */
+ unsigned int fill4:1;
+
+ unsigned int indexway:12;
+ unsigned int fill5:4;
+
+ unsigned int ctxnum:4;
+ unsigned int fill6:12;
+
+ unsigned long missvaddr:64; /* DW 1 */
+
+ unsigned int missasid:24; /* DW 2 */
+ unsigned int fill7:8;
+ unsigned int fillasid:24;
+ unsigned int dirty:1;
+ unsigned int gaa:2;
+ unsigned long fill8:5;
+
+ unsigned long pfn:41; /* DW 3 */
+ unsigned int fill9:7;
+ unsigned int pagesize:5;
+ unsigned int fill10:11;
+
+ unsigned long fillvaddr:64; /* DW 4 */
+
+ unsigned long fill11[3];
+};
+
+enum gru_tfh_opc {
+ TFHOP_NOOP,
+ TFHOP_RESTART,
+ TFHOP_WRITE_ONLY,
+ TFHOP_WRITE_RESTART,
+ TFHOP_EXCEPTION,
+ TFHOP_USER_POLLING_MODE = 7,
+};
+
+enum tfh_status {
+ TFHSTATUS_IDLE,
+ TFHSTATUS_EXCEPTION,
+ TFHSTATUS_ACTIVE,
+};
+
+enum tfh_state {
+ TFHSTATE_INACTIVE,
+ TFHSTATE_IDLE,
+ TFHSTATE_MISS_UPM,
+ TFHSTATE_MISS_FMM,
+ TFHSTATE_HW_ERR,
+ TFHSTATE_WRITE_TLB,
+ TFHSTATE_RESTART_CBR,
+};
+
+/* TFH cause bits */
+enum tfh_cause {
+ TFHCAUSE_NONE,
+ TFHCAUSE_TLB_MISS,
+ TFHCAUSE_TLB_MOD,
+ TFHCAUSE_HW_ERROR_RR,
+ TFHCAUSE_HW_ERROR_MAIN_ARRAY,
+ TFHCAUSE_HW_ERROR_VALID,
+ TFHCAUSE_HW_ERROR_PAGESIZE,
+ TFHCAUSE_INSTRUCTION_EXCEPTION,
+ TFHCAUSE_UNCORRECTIBLE_ERROR,
+};
+
+/* GAA values */
+#define GAA_RAM 0x0
+#define GAA_NCRAM 0x2
+#define GAA_MMIO 0x1
+#define GAA_REGISTER 0x3
+
+/* GRU paddr shift for pfn. (NOTE: shift is NOT by actual pagesize) */
+#define GRU_PADDR_SHIFT 12
+
+/*
+ * Context Configuration handle
+ * Used to allocate resources to a GSEG context.
+ *
+ */
+struct gru_context_configuration_handle {
+ unsigned int cmd:1; /* DW0 */
+ unsigned int delresp:1;
+ unsigned int opc:3;
+ unsigned int unmap_enable:1;
+ unsigned int req_slice_set_enable:1;
+ unsigned int req_slice:2;
+ unsigned int cb_int_enable:1;
+ unsigned int tlb_int_enable:1;
+ unsigned int tfm_fault_bit_enable:1;
+ unsigned int tlb_int_select:4;
+
+ unsigned int status:2;
+ unsigned int state:2;
+ unsigned int reserved2:4;
+
+ unsigned int cause:4;
+ unsigned int tfm_done_bit_enable:1;
+ unsigned int unused:3;
+
+ unsigned int dsr_allocation_map;
+
+ unsigned long cbr_allocation_map; /* DW1 */
+
+ unsigned int asid[8]; /* DW 2 - 5 */
+ unsigned short sizeavail[8]; /* DW 6 - 7 */
+} __attribute__ ((packed));
+
+enum gru_cch_opc {
+ CCHOP_START = 1,
+ CCHOP_ALLOCATE,
+ CCHOP_INTERRUPT,
+ CCHOP_DEALLOCATE,
+ CCHOP_INTERRUPT_SYNC,
+};
+
+enum gru_cch_status {
+ CCHSTATUS_IDLE,
+ CCHSTATUS_EXCEPTION,
+ CCHSTATUS_ACTIVE,
+};
+
+enum gru_cch_state {
+ CCHSTATE_INACTIVE,
+ CCHSTATE_MAPPED,
+ CCHSTATE_ACTIVE,
+ CCHSTATE_INTERRUPTED,
+};
+
+/* CCH Exception cause */
+enum gru_cch_cause {
+ CCHCAUSE_REGION_REGISTER_WRITE_ERROR = 1,
+ CCHCAUSE_ILLEGAL_OPCODE = 2,
+ CCHCAUSE_INVALID_START_REQUEST = 3,
+ CCHCAUSE_INVALID_ALLOCATION_REQUEST = 4,
+ CCHCAUSE_INVALID_DEALLOCATION_REQUEST = 5,
+ CCHCAUSE_INVALID_INTERRUPT_REQUEST = 6,
+ CCHCAUSE_CCH_BUSY = 7,
+ CCHCAUSE_NO_CBRS_TO_ALLOCATE = 8,
+ CCHCAUSE_BAD_TFM_CONFIG = 9,
+ CCHCAUSE_CBR_RESOURCES_OVERSUBSCRIPED = 10,
+ CCHCAUSE_DSR_RESOURCES_OVERSUBSCRIPED = 11,
+ CCHCAUSE_CBR_DEALLOCATION_ERROR = 12,
+};
+/*
+ * CBE - Control Block Extended
+ * Maintains internal GRU state for active CBs.
+ *
+ */
+struct gru_control_block_extended {
+ unsigned int reserved0:1; /* DW 0 - low */
+ unsigned int imacpy:3;
+ unsigned int reserved1:4;
+ unsigned int xtypecpy:3;
+ unsigned int iaa0cpy:2;
+ unsigned int iaa1cpy:2;
+ unsigned int reserved2:1;
+ unsigned int opccpy:8;
+ unsigned int exopccpy:8;
+
+ unsigned int idef2cpy:22; /* DW 0 - high */
+ unsigned int reserved3:10;
+
+ unsigned int idef4cpy:22; /* DW 1 */
+ unsigned int reserved4:10;
+ unsigned int idef4upd:22;
+ unsigned int reserved5:10;
+
+ unsigned long idef1upd:64; /* DW 2 */
+
+ unsigned long idef5cpy:64; /* DW 3 */
+
+ unsigned long idef6cpy:64; /* DW 4 */
+
+ unsigned long idef3upd:64; /* DW 5 */
+
+ unsigned long idef5upd:64; /* DW 6 */
+
+ unsigned int idef2upd:22; /* DW 7 */
+ unsigned int reserved6:10;
+
+ unsigned int ecause:20;
+ unsigned int cbrstate:4;
+ unsigned int cbrexecstatus:8;
+};
+
+enum gru_cbr_state {
+ CBRSTATE_INACTIVE,
+ CBRSTATE_IDLE,
+ CBRSTATE_PE_CHECK,
+ CBRSTATE_QUEUED,
+ CBRSTATE_WAIT_RESPONSE,
+ CBRSTATE_INTERRUPTED,
+ CBRSTATE_INTERRUPTED_MISS_FMM,
+ CBRSTATE_BUSY_INTERRUPT_MISS_FMM,
+ CBRSTATE_INTERRUPTED_MISS_UPM,
+ CBRSTATE_BUSY_INTERRUPTED_MISS_UPM,
+ CBRSTATE_REQUEST_ISSUE,
+ CBRSTATE_BUSY_INTERRUPT,
+};
+
+/* CBE cbrexecstatus bits */
+#define CBR_EXS_ABORT_OCC_BIT 0
+#define CBR_EXS_INT_OCC_BIT 1
+#define CBR_EXS_PENDING_BIT 2
+#define CBR_EXS_QUEUED_BIT 3
+#define CBR_EXS_TLBHW_BIT 4
+#define CBR_EXS_EXCEPTION_BIT 5
+
+#define CBR_EXS_ABORT_OCC (1 << CBR_EXS_ABORT_OCC_BIT)
+#define CBR_EXS_INT_OCC (1 << CBR_EXS_INT_OCC_BIT)
+#define CBR_EXS_PENDING (1 << CBR_EXS_PENDING_BIT)
+#define CBR_EXS_QUEUED (1 << CBR_EXS_QUEUED_BIT)
+#define CBR_EXS_TLBHW (1 << CBR_EXS_TLBHW_BIT)
+#define CBR_EXS_EXCEPTION (1 << CBR_EXS_EXCEPTION_BIT)
+
+/* CBE ecause bits - defined in gru_instructions.h */
+
+/*
+ * Convert a processor pagesize into the strange encoded pagesize used by the
+ * GRU. Processor pagesize is encoded as log of bytes per page. (or PAGE_SHIFT)
+ * pagesize log pagesize grupagesize
+ * 4k 12 0
+ * 16k 14 1
+ * 64k 16 2
+ * 256k 18 3
+ * 1m 20 4
+ * 2m 21 5
+ * 4m 22 6
+ * 16m 24 7
+ * 64m 26 8
+ * ...
+ */
+#define GRU_PAGESIZE(sh) ((((sh) > 20 ? (sh) + 2: (sh)) >> 1) - 6)
+#define GRU_SIZEAVAIL(sh) (1UL << GRU_PAGESIZE(sh))
+
+/* minimum TLB purge count to ensure a full purge */
+#define GRUMAXINVAL 1024UL
+
+
+/* Extract the status field from a kernel handle */
+#define GET_MSEG_HANDLE_STATUS(h) (((*(unsigned long *)(h)) >> 16) & 3)
+
+static inline void start_instruction(void *h)
+{
+ unsigned long *w0 = h;
+
+ wmb(); /* setting CMD bit must be last */
+ *w0 = *w0 | 1;
+ gru_flush_cache(h);
+}
+
+static inline int wait_instruction_complete(void *h)
+{
+ int status;
+
+ do {
+ cpu_relax();
+ barrier();
+ status = GET_MSEG_HANDLE_STATUS(h);
+ } while (status == CCHSTATUS_ACTIVE);
+ return status;
+}
+
+#if defined CONFIG_IA64
+static inline void cch_allocate_set_asids(
+ struct gru_context_configuration_handle *cch, int asidval)
+{
+ int i;
+
+ for (i = 0; i <= RGN_HPAGE; i++) { /* assume HPAGE is last region */
+ cch->asid[i] = (asidval++);
+#if 0
+ /* ZZZ hugepages not supported yet */
+ if (i == RGN_HPAGE)
+ cch->sizeavail[i] = GRU_SIZEAVAIL(hpage_shift);
+ else
+#endif
+ cch->sizeavail[i] = GRU_SIZEAVAIL(PAGE_SHIFT);
+ }
+}
+#elif defined CONFIG_X86_64
+static inline void cch_allocate_set_asids(
+ struct gru_context_configuration_handle *cch, int asidval)
+{
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ cch->asid[i] = asidval++;
+ cch->sizeavail[i] = GRU_SIZEAVAIL(PAGE_SHIFT) |
+ GRU_SIZEAVAIL(21);
+ }
+}
+#endif
+
+static inline int cch_allocate(struct gru_context_configuration_handle *cch,
+ int asidval, unsigned long cbrmap,
+ unsigned long dsrmap)
+{
+ cch_allocate_set_asids(cch, asidval);
+ cch->dsr_allocation_map = dsrmap;
+ cch->cbr_allocation_map = cbrmap;
+ cch->opc = CCHOP_ALLOCATE;
+ start_instruction(cch);
+ return wait_instruction_complete(cch);
+}
+
+static inline int cch_start(struct gru_context_configuration_handle *cch)
+{
+ cch->opc = CCHOP_START;
+ start_instruction(cch);
+ return wait_instruction_complete(cch);
+}
+
+static inline int cch_interrupt(struct gru_context_configuration_handle *cch)
+{
+ cch->opc = CCHOP_INTERRUPT;
+ start_instruction(cch);
+ return wait_instruction_complete(cch);
+}
+
+static inline int cch_deallocate(struct gru_context_configuration_handle *cch)
+{
+ cch->opc = CCHOP_DEALLOCATE;
+ start_instruction(cch);
+ return wait_instruction_complete(cch);
+}
+
+static inline int cch_interrupt_sync(struct gru_context_configuration_handle
+ *cch)
+{
+ cch->opc = CCHOP_INTERRUPT_SYNC;
+ start_instruction(cch);
+ return wait_instruction_complete(cch);
+}
+
+static inline int tgh_invalidate(struct gru_tlb_global_handle *tgh,
+ unsigned long vaddr, unsigned long vaddrmask,
+ int asid, int pagesize, int global, int n,
+ unsigned short ctxbitmap)
+{
+ tgh->vaddr = vaddr;
+ tgh->asid = asid;
+ tgh->pagesize = pagesize;
+ tgh->n = n;
+ tgh->global = global;
+ tgh->vaddrmask = vaddrmask;
+ tgh->ctxbitmap = ctxbitmap;
+ tgh->opc = TGHOP_TLBINV;
+ start_instruction(tgh);
+ return wait_instruction_complete(tgh);
+}
+
+static inline void tfh_write_only(struct gru_tlb_fault_handle *tfh,
+ unsigned long pfn, unsigned long vaddr,
+ int asid, int dirty, int pagesize)
+{
+ tfh->fillasid = asid;
+ tfh->fillvaddr = vaddr;
+ tfh->pfn = pfn;
+ tfh->dirty = dirty;
+ tfh->pagesize = pagesize;
+ tfh->opc = TFHOP_WRITE_ONLY;
+ start_instruction(tfh);
+}
+
+static inline void tfh_write_restart(struct gru_tlb_fault_handle *tfh,
+ unsigned long paddr, int gaa,
+ unsigned long vaddr, int asid, int dirty,
+ int pagesize)
+{
+ tfh->fillasid = asid;
+ tfh->fillvaddr = vaddr;
+ tfh->pfn = paddr >> GRU_PADDR_SHIFT;
+ tfh->gaa = gaa;
+ tfh->dirty = dirty;
+ tfh->pagesize = pagesize;
+ tfh->opc = TFHOP_WRITE_RESTART;
+ start_instruction(tfh);
+}
+
+static inline void tfh_restart(struct gru_tlb_fault_handle *tfh)
+{
+ tfh->opc = TFHOP_RESTART;
+ start_instruction(tfh);
+}
+
+static inline void tfh_user_polling_mode(struct gru_tlb_fault_handle *tfh)
+{
+ tfh->opc = TFHOP_USER_POLLING_MODE;
+ start_instruction(tfh);
+}
+
+static inline void tfh_exception(struct gru_tlb_fault_handle *tfh)
+{
+ tfh->opc = TFHOP_EXCEPTION;
+ start_instruction(tfh);
+}
+
+#endif /* __GRUHANDLES_H__ */
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * KERNEL SERVICES THAT USE THE GRU
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/smp_lock.h>
+#include <linux/spinlock.h>
+#include <linux/device.h>
+#include <linux/miscdevice.h>
+#include <linux/proc_fs.h>
+#include <linux/interrupt.h>
+#include <linux/uaccess.h>
+#include "gru.h"
+#include "grulib.h"
+#include "grutables.h"
+#include "grukservices.h"
+#include "gru_instructions.h"
+#include <asm/uv/uv_hub.h>
+
+/*
+ * Kernel GRU Usage
+ *
+ * The following is an interim algorithm for management of kernel GRU
+ * resources. This will likely be replaced when we better understand the
+ * kernel/user requirements.
+ *
+ * At boot time, the kernel permanently reserves a fixed number of
+ * CBRs/DSRs for each cpu to use. The resources are all taken from
+ * the GRU chiplet 1 on the blade. This leaves the full set of resources
+ * of chiplet 0 available to be allocated to a single user.
+ */
+
+/* Blade percpu resources PERMANENTLY reserved for kernel use */
+#define GRU_NUM_KERNEL_CBR 1
+#define GRU_NUM_KERNEL_DSR_BYTES 256
+#define KERNEL_CTXNUM 15
+
+/* GRU instruction attributes for all instructions */
+#define IMA IMA_CB_DELAY
+
+/* GRU cacheline size is always 64 bytes - even on arches with 128 byte lines */
+#define __gru_cacheline_aligned__ \
+ __attribute__((__aligned__(GRU_CACHE_LINE_BYTES)))
+
+#define MAGIC 0x1234567887654321UL
+
+/* Default retry count for GRU errors on kernel instructions */
+#define EXCEPTION_RETRY_LIMIT 3
+
+/* Status of message queue sections */
+#define MQS_EMPTY 0
+#define MQS_FULL 1
+#define MQS_NOOP 2
+
+/*----------------- RESOURCE MANAGEMENT -------------------------------------*/
+/* optimized for x86_64 */
+struct message_queue {
+ union gru_mesqhead head __gru_cacheline_aligned__; /* CL 0 */
+ int qlines; /* DW 1 */
+ long hstatus[2];
+ void *next __gru_cacheline_aligned__;/* CL 1 */
+ void *limit;
+ void *start;
+ void *start2;
+ char data ____cacheline_aligned; /* CL 2 */
+};
+
+/* First word in every message - used by mesq interface */
+struct message_header {
+ char present;
+ char present2;
+ char lines;
+ char fill;
+};
+
+#define QLINES(mq) ((mq) + offsetof(struct message_queue, qlines))
+#define HSTATUS(mq, h) ((mq) + offsetof(struct message_queue, hstatus[h]))
+
+static int gru_get_cpu_resources(int dsr_bytes, void **cb, void **dsr)
+{
+ struct gru_blade_state *bs;
+ int lcpu;
+
+ BUG_ON(dsr_bytes > GRU_NUM_KERNEL_DSR_BYTES);
+ preempt_disable();
+ bs = gru_base[uv_numa_blade_id()];
+ lcpu = uv_blade_processor_id();
+ *cb = bs->kernel_cb + lcpu * GRU_HANDLE_STRIDE;
+ *dsr = bs->kernel_dsr + lcpu * GRU_NUM_KERNEL_DSR_BYTES;
+ return 0;
+}
+
+static void gru_free_cpu_resources(void *cb, void *dsr)
+{
+ preempt_enable();
+}
+
+int gru_get_cb_exception_detail(void *cb,
+ struct control_block_extended_exc_detail *excdet)
+{
+ struct gru_control_block_extended *cbe;
+
+ cbe = get_cbe(GRUBASE(cb), get_cb_number(cb));
+ excdet->opc = cbe->opccpy;
+ excdet->exopc = cbe->exopccpy;
+ excdet->ecause = cbe->ecause;
+ excdet->exceptdet0 = cbe->idef1upd;
+ excdet->exceptdet1 = cbe->idef3upd;
+ return 0;
+}
+
+char *gru_get_cb_exception_detail_str(int ret, void *cb,
+ char *buf, int size)
+{
+ struct gru_control_block_status *gen = (void *)cb;
+ struct control_block_extended_exc_detail excdet;
+
+ if (ret > 0 && gen->istatus == CBS_EXCEPTION) {
+ gru_get_cb_exception_detail(cb, &excdet);
+ snprintf(buf, size,
+ "GRU exception: cb %p, opc %d, exopc %d, ecause 0x%x,"
+ "excdet0 0x%lx, excdet1 0x%x",
+ gen, excdet.opc, excdet.exopc, excdet.ecause,
+ excdet.exceptdet0, excdet.exceptdet1);
+ } else {
+ snprintf(buf, size, "No exception");
+ }
+ return buf;
+}
+
+static int gru_wait_idle_or_exception(struct gru_control_block_status *gen)
+{
+ while (gen->istatus >= CBS_ACTIVE) {
+ cpu_relax();
+ barrier();
+ }
+ return gen->istatus;
+}
+
+static int gru_retry_exception(void *cb)
+{
+ struct gru_control_block_status *gen = (void *)cb;
+ struct control_block_extended_exc_detail excdet;
+ int retry = EXCEPTION_RETRY_LIMIT;
+
+ while (1) {
+ if (gru_get_cb_message_queue_substatus(cb))
+ break;
+ if (gru_wait_idle_or_exception(gen) == CBS_IDLE)
+ return CBS_IDLE;
+
+ gru_get_cb_exception_detail(cb, &excdet);
+ if (excdet.ecause & ~EXCEPTION_RETRY_BITS)
+ break;
+ if (retry-- == 0)
+ break;
+ gen->icmd = 1;
+ gru_flush_cache(gen);
+ }
+ return CBS_EXCEPTION;
+}
+
+int gru_check_status_proc(void *cb)
+{
+ struct gru_control_block_status *gen = (void *)cb;
+ int ret;
+
+ ret = gen->istatus;
+ if (ret != CBS_EXCEPTION)
+ return ret;
+ return gru_retry_exception(cb);
+
+}
+
+int gru_wait_proc(void *cb)
+{
+ struct gru_control_block_status *gen = (void *)cb;
+ int ret;
+
+ ret = gru_wait_idle_or_exception(gen);
+ if (ret == CBS_EXCEPTION)
+ ret = gru_retry_exception(cb);
+
+ return ret;
+}
+
+void gru_abort(int ret, void *cb, char *str)
+{
+ char buf[GRU_EXC_STR_SIZE];
+
+ panic("GRU FATAL ERROR: %s - %s\n", str,
+ gru_get_cb_exception_detail_str(ret, cb, buf, sizeof(buf)));
+}
+
+void gru_wait_abort_proc(void *cb)
+{
+ int ret;
+
+ ret = gru_wait_proc(cb);
+ if (ret)
+ gru_abort(ret, cb, "gru_wait_abort");
+}
+
+
+/*------------------------------ MESSAGE QUEUES -----------------------------*/
+
+/* Internal status . These are NOT returned to the user. */
+#define MQIE_AGAIN -1 /* try again */
+
+
+/*
+ * Save/restore the "present" flag that is in the second line of 2-line
+ * messages
+ */
+static inline int get_present2(void *p)
+{
+ struct message_header *mhdr = p + GRU_CACHE_LINE_BYTES;
+ return mhdr->present;
+}
+
+static inline void restore_present2(void *p, int val)
+{
+ struct message_header *mhdr = p + GRU_CACHE_LINE_BYTES;
+ mhdr->present = val;
+}
+
+/*
+ * Create a message queue.
+ * qlines - message queue size in cache lines. Includes 2-line header.
+ */
+int gru_create_message_queue(void *p, unsigned int bytes)
+{
+ struct message_queue *mq = p;
+ unsigned int qlines;
+
+ qlines = bytes / GRU_CACHE_LINE_BYTES - 2;
+ memset(mq, 0, bytes);
+ mq->start = &mq->data;
+ mq->start2 = &mq->data + (qlines / 2 - 1) * GRU_CACHE_LINE_BYTES;
+ mq->next = &mq->data;
+ mq->limit = &mq->data + (qlines - 2) * GRU_CACHE_LINE_BYTES;
+ mq->qlines = qlines;
+ mq->hstatus[0] = 0;
+ mq->hstatus[1] = 1;
+ mq->head = gru_mesq_head(2, qlines / 2 + 1);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(gru_create_message_queue);
+
+/*
+ * Send a NOOP message to a message queue
+ * Returns:
+ * 0 - if queue is full after the send. This is the normal case
+ * but various races can change this.
+ * -1 - if mesq sent successfully but queue not full
+ * >0 - unexpected error. MQE_xxx returned
+ */
+static int send_noop_message(void *cb,
+ unsigned long mq, void *mesg)
+{
+ const struct message_header noop_header = {
+ .present = MQS_NOOP, .lines = 1};
+ unsigned long m;
+ int substatus, ret;
+ struct message_header save_mhdr, *mhdr = mesg;
+
+ STAT(mesq_noop);
+ save_mhdr = *mhdr;
+ *mhdr = noop_header;
+ gru_mesq(cb, mq, gru_get_tri(mhdr), 1, IMA);
+ ret = gru_wait(cb);
+
+ if (ret) {
+ substatus = gru_get_cb_message_queue_substatus(cb);
+ switch (substatus) {
+ case CBSS_NO_ERROR:
+ STAT(mesq_noop_unexpected_error);
+ ret = MQE_UNEXPECTED_CB_ERR;
+ break;
+ case CBSS_LB_OVERFLOWED:
+ STAT(mesq_noop_lb_overflow);
+ ret = MQE_CONGESTION;
+ break;
+ case CBSS_QLIMIT_REACHED:
+ STAT(mesq_noop_qlimit_reached);
+ ret = 0;
+ break;
+ case CBSS_AMO_NACKED:
+ STAT(mesq_noop_amo_nacked);
+ ret = MQE_CONGESTION;
+ break;
+ case CBSS_PUT_NACKED:
+ STAT(mesq_noop_put_nacked);
+ m = mq + (gru_get_amo_value_head(cb) << 6);
+ gru_vstore(cb, m, gru_get_tri(mesg), XTYPE_CL, 1, 1,
+ IMA);
+ if (gru_wait(cb) == CBS_IDLE)
+ ret = MQIE_AGAIN;
+ else
+ ret = MQE_UNEXPECTED_CB_ERR;
+ break;
+ case CBSS_PAGE_OVERFLOW:
+ default:
+ BUG();
+ }
+ }
+ *mhdr = save_mhdr;
+ return ret;
+}
+
+/*
+ * Handle a gru_mesq full.
+ */
+static int send_message_queue_full(void *cb,
+ unsigned long mq, void *mesg, int lines)
+{
+ union gru_mesqhead mqh;
+ unsigned int limit, head;
+ unsigned long avalue;
+ int half, qlines, save;
+
+ /* Determine if switching to first/second half of q */
+ avalue = gru_get_amo_value(cb);
+ head = gru_get_amo_value_head(cb);
+ limit = gru_get_amo_value_limit(cb);
+
+ /*
+ * Fetch "qlines" from the queue header. Since the queue may be
+ * in memory that can't be accessed using socket addresses, use
+ * the GRU to access the data. Use DSR space from the message.
+ */
+ save = *(int *)mesg;
+ gru_vload(cb, QLINES(mq), gru_get_tri(mesg), XTYPE_W, 1, 1, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ goto cberr;
+ qlines = *(int *)mesg;
+ *(int *)mesg = save;
+ half = (limit != qlines);
+
+ if (half)
+ mqh = gru_mesq_head(qlines / 2 + 1, qlines);
+ else
+ mqh = gru_mesq_head(2, qlines / 2 + 1);
+
+ /* Try to get lock for switching head pointer */
+ gru_gamir(cb, EOP_IR_CLR, HSTATUS(mq, half), XTYPE_DW, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ goto cberr;
+ if (!gru_get_amo_value(cb)) {
+ STAT(mesq_qf_locked);
+ return MQE_QUEUE_FULL;
+ }
+
+ /* Got the lock. Send optional NOP if queue not full, */
+ if (head != limit) {
+ if (send_noop_message(cb, mq, mesg)) {
+ gru_gamir(cb, EOP_IR_INC, HSTATUS(mq, half),
+ XTYPE_DW, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ goto cberr;
+ STAT(mesq_qf_noop_not_full);
+ return MQIE_AGAIN;
+ }
+ avalue++;
+ }
+
+ /* Then flip queuehead to other half of queue. */
+ gru_gamer(cb, EOP_ERR_CSWAP, mq, XTYPE_DW, mqh.val, avalue, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ goto cberr;
+
+ /* If not successfully in swapping queue head, clear the hstatus lock */
+ if (gru_get_amo_value(cb) != avalue) {
+ STAT(mesq_qf_switch_head_failed);
+ gru_gamir(cb, EOP_IR_INC, HSTATUS(mq, half), XTYPE_DW, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ goto cberr;
+ }
+ return MQIE_AGAIN;
+cberr:
+ STAT(mesq_qf_unexpected_error);
+ return MQE_UNEXPECTED_CB_ERR;
+}
+
+
+/*
+ * Handle a gru_mesq failure. Some of these failures are software recoverable
+ * or retryable.
+ */
+static int send_message_failure(void *cb,
+ unsigned long mq,
+ void *mesg,
+ int lines)
+{
+ int substatus, ret = 0;
+ unsigned long m;
+
+ substatus = gru_get_cb_message_queue_substatus(cb);
+ switch (substatus) {
+ case CBSS_NO_ERROR:
+ STAT(mesq_send_unexpected_error);
+ ret = MQE_UNEXPECTED_CB_ERR;
+ break;
+ case CBSS_LB_OVERFLOWED:
+ STAT(mesq_send_lb_overflow);
+ ret = MQE_CONGESTION;
+ break;
+ case CBSS_QLIMIT_REACHED:
+ STAT(mesq_send_qlimit_reached);
+ ret = send_message_queue_full(cb, mq, mesg, lines);
+ break;
+ case CBSS_AMO_NACKED:
+ STAT(mesq_send_amo_nacked);
+ ret = MQE_CONGESTION;
+ break;
+ case CBSS_PUT_NACKED:
+ STAT(mesq_send_put_nacked);
+ m =mq + (gru_get_amo_value_head(cb) << 6);
+ gru_vstore(cb, m, gru_get_tri(mesg), XTYPE_CL, lines, 1, IMA);
+ if (gru_wait(cb) == CBS_IDLE)
+ ret = MQE_OK;
+ else
+ ret = MQE_UNEXPECTED_CB_ERR;
+ break;
+ default:
+ BUG();
+ }
+ return ret;
+}
+
+/*
+ * Send a message to a message queue
+ * cb GRU control block to use to send message
+ * mq message queue
+ * mesg message. ust be vaddr within a GSEG
+ * bytes message size (<= 2 CL)
+ */
+int gru_send_message_gpa(unsigned long mq, void *mesg, unsigned int bytes)
+{
+ struct message_header *mhdr;
+ void *cb;
+ void *dsr;
+ int istatus, clines, ret;
+
+ STAT(mesq_send);
+ BUG_ON(bytes < sizeof(int) || bytes > 2 * GRU_CACHE_LINE_BYTES);
+
+ clines = (bytes + GRU_CACHE_LINE_BYTES - 1) / GRU_CACHE_LINE_BYTES;
+ if (gru_get_cpu_resources(bytes, &cb, &dsr))
+ return MQE_BUG_NO_RESOURCES;
+ memcpy(dsr, mesg, bytes);
+ mhdr = dsr;
+ mhdr->present = MQS_FULL;
+ mhdr->lines = clines;
+ if (clines == 2) {
+ mhdr->present2 = get_present2(mhdr);
+ restore_present2(mhdr, MQS_FULL);
+ }
+
+ do {
+ ret = MQE_OK;
+ gru_mesq(cb, mq, gru_get_tri(mhdr), clines, IMA);
+ istatus = gru_wait(cb);
+ if (istatus != CBS_IDLE)
+ ret = send_message_failure(cb, mq, dsr, clines);
+ } while (ret == MQIE_AGAIN);
+ gru_free_cpu_resources(cb, dsr);
+
+ if (ret)
+ STAT(mesq_send_failed);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(gru_send_message_gpa);
+
+/*
+ * Advance the receive pointer for the queue to the next message.
+ */
+void gru_free_message(void *rmq, void *mesg)
+{
+ struct message_queue *mq = rmq;
+ struct message_header *mhdr = mq->next;
+ void *next, *pnext;
+ int half = -1;
+ int lines = mhdr->lines;
+
+ if (lines == 2)
+ restore_present2(mhdr, MQS_EMPTY);
+ mhdr->present = MQS_EMPTY;
+
+ pnext = mq->next;
+ next = pnext + GRU_CACHE_LINE_BYTES * lines;
+ if (next == mq->limit) {
+ next = mq->start;
+ half = 1;
+ } else if (pnext < mq->start2 && next >= mq->start2) {
+ half = 0;
+ }
+
+ if (half >= 0)
+ mq->hstatus[half] = 1;
+ mq->next = next;
+}
+EXPORT_SYMBOL_GPL(gru_free_message);
+
+/*
+ * Get next message from message queue. Return NULL if no message
+ * present. User must call next_message() to move to next message.
+ * rmq message queue
+ */
+void *gru_get_next_message(void *rmq)
+{
+ struct message_queue *mq = rmq;
+ struct message_header *mhdr = mq->next;
+ int present = mhdr->present;
+
+ /* skip NOOP messages */
+ STAT(mesq_receive);
+ while (present == MQS_NOOP) {
+ gru_free_message(rmq, mhdr);
+ mhdr = mq->next;
+ present = mhdr->present;
+ }
+
+ /* Wait for both halves of 2 line messages */
+ if (present == MQS_FULL && mhdr->lines == 2 &&
+ get_present2(mhdr) == MQS_EMPTY)
+ present = MQS_EMPTY;
+
+ if (!present) {
+ STAT(mesq_receive_none);
+ return NULL;
+ }
+
+ if (mhdr->lines == 2)
+ restore_present2(mhdr, mhdr->present2);
+
+ return mhdr;
+}
+EXPORT_SYMBOL_GPL(gru_get_next_message);
+
+/* ---------------------- GRU DATA COPY FUNCTIONS ---------------------------*/
+
+/*
+ * Copy a block of data using the GRU resources
+ */
+int gru_copy_gpa(unsigned long dest_gpa, unsigned long src_gpa,
+ unsigned int bytes)
+{
+ void *cb;
+ void *dsr;
+ int ret;
+
+ STAT(copy_gpa);
+ if (gru_get_cpu_resources(GRU_NUM_KERNEL_DSR_BYTES, &cb, &dsr))
+ return MQE_BUG_NO_RESOURCES;
+ gru_bcopy(cb, src_gpa, dest_gpa, gru_get_tri(dsr),
+ XTYPE_B, bytes, GRU_NUM_KERNEL_DSR_BYTES, IMA);
+ ret = gru_wait(cb);
+ gru_free_cpu_resources(cb, dsr);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(gru_copy_gpa);
+
+/* ------------------- KERNEL QUICKTESTS RUN AT STARTUP ----------------*/
+/* Temp - will delete after we gain confidence in the GRU */
+static __cacheline_aligned unsigned long word0;
+static __cacheline_aligned unsigned long word1;
+
+static int quicktest(struct gru_state *gru)
+{
+ void *cb;
+ void *ds;
+ unsigned long *p;
+
+ cb = get_gseg_base_address_cb(gru->gs_gru_base_vaddr, KERNEL_CTXNUM, 0);
+ ds = get_gseg_base_address_ds(gru->gs_gru_base_vaddr, KERNEL_CTXNUM, 0);
+ p = ds;
+ word0 = MAGIC;
+
+ gru_vload(cb, uv_gpa(&word0), 0, XTYPE_DW, 1, 1, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ BUG();
+
+ if (*(unsigned long *)ds != MAGIC)
+ BUG();
+ gru_vstore(cb, uv_gpa(&word1), 0, XTYPE_DW, 1, 1, IMA);
+ if (gru_wait(cb) != CBS_IDLE)
+ BUG();
+
+ if (word0 != word1 || word0 != MAGIC) {
+ printk
+ ("GRU quicktest err: gru %d, found 0x%lx, expected 0x%lx\n",
+ gru->gs_gid, word1, MAGIC);
+ BUG(); /* ZZZ should not be fatal */
+ }
+
+ return 0;
+}
+
+
+int gru_kservices_init(struct gru_state *gru)
+{
+ struct gru_blade_state *bs;
+ struct gru_context_configuration_handle *cch;
+ unsigned long cbr_map, dsr_map;
+ int err, num, cpus_possible;
+
+ /*
+ * Currently, resources are reserved ONLY on the second chiplet
+ * on each blade. This leaves ALL resources on chiplet 0 available
+ * for user code.
+ */
+ bs = gru->gs_blade;
+ if (gru != &bs->bs_grus[1])
+ return 0;
+
+ cpus_possible = uv_blade_nr_possible_cpus(gru->gs_blade_id);
+
+ num = GRU_NUM_KERNEL_CBR * cpus_possible;
+ cbr_map = gru_reserve_cb_resources(gru, GRU_CB_COUNT_TO_AU(num), NULL);
+ gru->gs_reserved_cbrs += num;
+
+ num = GRU_NUM_KERNEL_DSR_BYTES * cpus_possible;
+ dsr_map = gru_reserve_ds_resources(gru, GRU_DS_BYTES_TO_AU(num), NULL);
+ gru->gs_reserved_dsr_bytes += num;
+
+ gru->gs_active_contexts++;
+ __set_bit(KERNEL_CTXNUM, &gru->gs_context_map);
+ cch = get_cch(gru->gs_gru_base_vaddr, KERNEL_CTXNUM);
+
+ bs->kernel_cb = get_gseg_base_address_cb(gru->gs_gru_base_vaddr,
+ KERNEL_CTXNUM, 0);
+ bs->kernel_dsr = get_gseg_base_address_ds(gru->gs_gru_base_vaddr,
+ KERNEL_CTXNUM, 0);
+
+ lock_cch_handle(cch);
+ cch->tfm_fault_bit_enable = 0;
+ cch->tlb_int_enable = 0;
+ cch->tfm_done_bit_enable = 0;
+ cch->unmap_enable = 1;
+ err = cch_allocate(cch, 0, cbr_map, dsr_map);
+ if (err) {
+ gru_dbg(grudev,
+ "Unable to allocate kernel CCH: gru %d, err %d\n",
+ gru->gs_gid, err);
+ BUG();
+ }
+ if (cch_start(cch)) {
+ gru_dbg(grudev, "Unable to start kernel CCH: gru %d, err %d\n",
+ gru->gs_gid, err);
+ BUG();
+ }
+ unlock_cch_handle(cch);
+
+ if (gru_options & GRU_QUICKLOOK)
+ quicktest(gru);
+ return 0;
+}
--- /dev/null
+
+/*
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __GRU_KSERVICES_H_
+#define __GRU_KSERVICES_H_
+
+
+/*
+ * Message queues using the GRU to send/receive messages.
+ *
+ * These function allow the user to create a message queue for
+ * sending/receiving 1 or 2 cacheline messages using the GRU.
+ *
+ * Processes SENDING messages will use a kernel CBR/DSR to send
+ * the message. This is transparent to the caller.
+ *
+ * The receiver does not use any GRU resources.
+ *
+ * The functions support:
+ * - single receiver
+ * - multiple senders
+ * - cross partition message
+ *
+ * Missing features ZZZ:
+ * - user options for dealing with timeouts, queue full, etc.
+ * - gru_create_message_queue() needs interrupt vector info
+ */
+
+/*
+ * Initialize a user allocated chunk of memory to be used as
+ * a message queue. The caller must ensure that the queue is
+ * in contiguous physical memory and is cacheline aligned.
+ *
+ * Message queue size is the total number of bytes allocated
+ * to the queue including a 2 cacheline header that is used
+ * to manage the queue.
+ *
+ * Input:
+ * p pointer to user allocated memory.
+ * bytes size of message queue in bytes
+ *
+ * Errors:
+ * 0 OK
+ * >0 error
+ */
+extern int gru_create_message_queue(void *p, unsigned int bytes);
+
+/*
+ * Send a message to a message queue.
+ *
+ * Note: The message queue transport mechanism uses the first 32
+ * bits of the message. Users should avoid using these bits.
+ *
+ *
+ * Input:
+ * xmq message queue - must be a UV global physical address
+ * mesg pointer to message. Must be 64-bit aligned
+ * bytes size of message in bytes
+ *
+ * Output:
+ * 0 message sent
+ * >0 Send failure - see error codes below
+ *
+ */
+extern int gru_send_message_gpa(unsigned long mq_gpa, void *mesg,
+ unsigned int bytes);
+
+/* Status values for gru_send_message() */
+#define MQE_OK 0 /* message sent successfully */
+#define MQE_CONGESTION 1 /* temporary congestion, try again */
+#define MQE_QUEUE_FULL 2 /* queue is full */
+#define MQE_UNEXPECTED_CB_ERR 3 /* unexpected CB error */
+#define MQE_PAGE_OVERFLOW 10 /* BUG - queue overflowed a page */
+#define MQE_BUG_NO_RESOURCES 11 /* BUG - could not alloc GRU cb/dsr */
+
+/*
+ * Advance the receive pointer for the message queue to the next message.
+ * Note: current API requires messages to be gotten & freed in order. Future
+ * API extensions may allow for out-of-order freeing.
+ *
+ * Input
+ * mq message queue
+ * mesq message being freed
+ */
+extern void gru_free_message(void *mq, void *mesq);
+
+/*
+ * Get next message from message queue. Returns pointer to
+ * message OR NULL if no message present.
+ * User must call gru_free_message() after message is processed
+ * in order to move the queue pointers to next message.
+ *
+ * Input
+ * mq message queue
+ *
+ * Output:
+ * p pointer to message
+ * NULL no message available
+ */
+extern void *gru_get_next_message(void *mq);
+
+
+/*
+ * Copy data using the GRU. Source or destination can be located in a remote
+ * partition.
+ *
+ * Input:
+ * dest_gpa destination global physical address
+ * src_gpa source global physical address
+ * bytes number of bytes to copy
+ *
+ * Output:
+ * 0 OK
+ * >0 error
+ */
+extern int gru_copy_gpa(unsigned long dest_gpa, unsigned long src_gpa,
+ unsigned int bytes);
+
+#endif /* __GRU_KSERVICES_H_ */
--- /dev/null
+/*
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU Lesser General Public License as published by
+ * the Free Software Foundation; either version 2.1 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __GRULIB_H__
+#define __GRULIB_H__
+
+#define GRU_BASENAME "gru"
+#define GRU_FULLNAME "/dev/gru"
+#define GRU_IOCTL_NUM 'G'
+
+/*
+ * Maximum number of GRU segments that a user can have open
+ * ZZZ temp - set high for testing. Revisit.
+ */
+#define GRU_MAX_OPEN_CONTEXTS 32
+
+/* Set Number of Request Blocks */
+#define GRU_CREATE_CONTEXT _IOWR(GRU_IOCTL_NUM, 1, void *)
+
+/* Register task as using the slice */
+#define GRU_SET_TASK_SLICE _IOWR(GRU_IOCTL_NUM, 5, void *)
+
+/* Fetch exception detail */
+#define GRU_USER_GET_EXCEPTION_DETAIL _IOWR(GRU_IOCTL_NUM, 6, void *)
+
+/* For user call_os handling - normally a TLB fault */
+#define GRU_USER_CALL_OS _IOWR(GRU_IOCTL_NUM, 8, void *)
+
+/* For user unload context */
+#define GRU_USER_UNLOAD_CONTEXT _IOWR(GRU_IOCTL_NUM, 9, void *)
+
+/* For fetching GRU chiplet status */
+#define GRU_GET_CHIPLET_STATUS _IOWR(GRU_IOCTL_NUM, 10, void *)
+
+/* For user TLB flushing (primarily for tests) */
+#define GRU_USER_FLUSH_TLB _IOWR(GRU_IOCTL_NUM, 50, void *)
+
+/* Get some config options (primarily for tests & emulator) */
+#define GRU_GET_CONFIG_INFO _IOWR(GRU_IOCTL_NUM, 51, void *)
+
+#define CONTEXT_WINDOW_BYTES(th) (GRU_GSEG_PAGESIZE * (th))
+#define THREAD_POINTER(p, th) (p + GRU_GSEG_PAGESIZE * (th))
+
+/*
+ * Structure used to pass TLB flush parameters to the driver
+ */
+struct gru_create_context_req {
+ unsigned long gseg;
+ unsigned int data_segment_bytes;
+ unsigned int control_blocks;
+ unsigned int maximum_thread_count;
+ unsigned int options;
+};
+
+/*
+ * Structure used to pass unload context parameters to the driver
+ */
+struct gru_unload_context_req {
+ unsigned long gseg;
+};
+
+/*
+ * Structure used to pass TLB flush parameters to the driver
+ */
+struct gru_flush_tlb_req {
+ unsigned long gseg;
+ unsigned long vaddr;
+ size_t len;
+};
+
+/*
+ * GRU configuration info (temp - for testing)
+ */
+struct gru_config_info {
+ int cpus;
+ int blades;
+ int nodes;
+ int chiplets;
+ int fill[16];
+};
+
+#endif /* __GRULIB_H__ */
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * DRIVER TABLE MANAGER + GRU CONTEXT LOAD/UNLOAD
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/spinlock.h>
+#include <linux/sched.h>
+#include <linux/device.h>
+#include <linux/list.h>
+#include <asm/uv/uv_hub.h>
+#include "gru.h"
+#include "grutables.h"
+#include "gruhandles.h"
+
+unsigned long gru_options __read_mostly;
+
+static struct device_driver gru_driver = {
+ .name = "gru"
+};
+
+static struct device gru_device = {
+ .bus_id = {0},
+ .driver = &gru_driver,
+};
+
+struct device *grudev = &gru_device;
+
+/*
+ * Select a gru fault map to be used by the current cpu. Note that
+ * multiple cpus may be using the same map.
+ * ZZZ should "shift" be used?? Depends on HT cpu numbering
+ * ZZZ should be inline but did not work on emulator
+ */
+int gru_cpu_fault_map_id(void)
+{
+ return uv_blade_processor_id() % GRU_NUM_TFM;
+}
+
+/*--------- ASID Management -------------------------------------------
+ *
+ * Initially, assign asids sequentially from MIN_ASID .. MAX_ASID.
+ * Once MAX is reached, flush the TLB & start over. However,
+ * some asids may still be in use. There won't be many (percentage wise) still
+ * in use. Search active contexts & determine the value of the first
+ * asid in use ("x"s below). Set "limit" to this value.
+ * This defines a block of assignable asids.
+ *
+ * When "limit" is reached, search forward from limit+1 and determine the
+ * next block of assignable asids.
+ *
+ * Repeat until MAX_ASID is reached, then start over again.
+ *
+ * Each time MAX_ASID is reached, increment the asid generation. Since
+ * the search for in-use asids only checks contexts with GRUs currently
+ * assigned, asids in some contexts will be missed. Prior to loading
+ * a context, the asid generation of the GTS asid is rechecked. If it
+ * doesn't match the current generation, a new asid will be assigned.
+ *
+ * 0---------------x------------x---------------------x----|
+ * ^-next ^-limit ^-MAX_ASID
+ *
+ * All asid manipulation & context loading/unloading is protected by the
+ * gs_lock.
+ */
+
+/* Hit the asid limit. Start over */
+static int gru_wrap_asid(struct gru_state *gru)
+{
+ gru_dbg(grudev, "gru %p\n", gru);
+ STAT(asid_wrap);
+ gru->gs_asid_gen++;
+ gru_flush_all_tlb(gru);
+ return MIN_ASID;
+}
+
+/* Find the next chunk of unused asids */
+static int gru_reset_asid_limit(struct gru_state *gru, int asid)
+{
+ int i, gid, inuse_asid, limit;
+
+ gru_dbg(grudev, "gru %p, asid 0x%x\n", gru, asid);
+ STAT(asid_next);
+ limit = MAX_ASID;
+ if (asid >= limit)
+ asid = gru_wrap_asid(gru);
+ gid = gru->gs_gid;
+again:
+ for (i = 0; i < GRU_NUM_CCH; i++) {
+ if (!gru->gs_gts[i])
+ continue;
+ inuse_asid = gru->gs_gts[i]->ts_gms->ms_asids[gid].mt_asid;
+ gru_dbg(grudev, "gru %p, inuse_asid 0x%x, cxtnum %d, gts %p\n",
+ gru, inuse_asid, i, gru->gs_gts[i]);
+ if (inuse_asid == asid) {
+ asid += ASID_INC;
+ if (asid >= limit) {
+ /*
+ * empty range: reset the range limit and
+ * start over
+ */
+ limit = MAX_ASID;
+ if (asid >= MAX_ASID)
+ asid = gru_wrap_asid(gru);
+ goto again;
+ }
+ }
+
+ if ((inuse_asid > asid) && (inuse_asid < limit))
+ limit = inuse_asid;
+ }
+ gru->gs_asid_limit = limit;
+ gru->gs_asid = asid;
+ gru_dbg(grudev, "gru %p, new asid 0x%x, new_limit 0x%x\n", gru, asid,
+ limit);
+ return asid;
+}
+
+/* Assign a new ASID to a thread context. */
+static int gru_assign_asid(struct gru_state *gru)
+{
+ int asid;
+
+ spin_lock(&gru->gs_asid_lock);
+ gru->gs_asid += ASID_INC;
+ asid = gru->gs_asid;
+ if (asid >= gru->gs_asid_limit)
+ asid = gru_reset_asid_limit(gru, asid);
+ spin_unlock(&gru->gs_asid_lock);
+
+ gru_dbg(grudev, "gru %p, asid 0x%x\n", gru, asid);
+ return asid;
+}
+
+/*
+ * Clear n bits in a word. Return a word indicating the bits that were cleared.
+ * Optionally, build an array of chars that contain the bit numbers allocated.
+ */
+static unsigned long reserve_resources(unsigned long *p, int n, int mmax,
+ char *idx)
+{
+ unsigned long bits = 0;
+ int i;
+
+ do {
+ i = find_first_bit(p, mmax);
+ if (i == mmax)
+ BUG();
+ __clear_bit(i, p);
+ __set_bit(i, &bits);
+ if (idx)
+ *idx++ = i;
+ } while (--n);
+ return bits;
+}
+
+unsigned long gru_reserve_cb_resources(struct gru_state *gru, int cbr_au_count,
+ char *cbmap)
+{
+ return reserve_resources(&gru->gs_cbr_map, cbr_au_count, GRU_CBR_AU,
+ cbmap);
+}
+
+unsigned long gru_reserve_ds_resources(struct gru_state *gru, int dsr_au_count,
+ char *dsmap)
+{
+ return reserve_resources(&gru->gs_dsr_map, dsr_au_count, GRU_DSR_AU,
+ dsmap);
+}
+
+static void reserve_gru_resources(struct gru_state *gru,
+ struct gru_thread_state *gts)
+{
+ gru->gs_active_contexts++;
+ gts->ts_cbr_map =
+ gru_reserve_cb_resources(gru, gts->ts_cbr_au_count,
+ gts->ts_cbr_idx);
+ gts->ts_dsr_map =
+ gru_reserve_ds_resources(gru, gts->ts_dsr_au_count, NULL);
+}
+
+static void free_gru_resources(struct gru_state *gru,
+ struct gru_thread_state *gts)
+{
+ gru->gs_active_contexts--;
+ gru->gs_cbr_map |= gts->ts_cbr_map;
+ gru->gs_dsr_map |= gts->ts_dsr_map;
+}
+
+/*
+ * Check if a GRU has sufficient free resources to satisfy an allocation
+ * request. Note: GRU locks may or may not be held when this is called. If
+ * not held, recheck after acquiring the appropriate locks.
+ *
+ * Returns 1 if sufficient resources, 0 if not
+ */
+static int check_gru_resources(struct gru_state *gru, int cbr_au_count,
+ int dsr_au_count, int max_active_contexts)
+{
+ return hweight64(gru->gs_cbr_map) >= cbr_au_count
+ && hweight64(gru->gs_dsr_map) >= dsr_au_count
+ && gru->gs_active_contexts < max_active_contexts;
+}
+
+/*
+ * TLB manangment requires tracking all GRU chiplets that have loaded a GSEG
+ * context.
+ */
+static int gru_load_mm_tracker(struct gru_state *gru, struct gru_mm_struct *gms,
+ int ctxnum)
+{
+ struct gru_mm_tracker *asids = &gms->ms_asids[gru->gs_gid];
+ unsigned short ctxbitmap = (1 << ctxnum);
+ int asid;
+
+ spin_lock(&gms->ms_asid_lock);
+ asid = asids->mt_asid;
+
+ if (asid == 0 || asids->mt_asid_gen != gru->gs_asid_gen) {
+ asid = gru_assign_asid(gru);
+ asids->mt_asid = asid;
+ asids->mt_asid_gen = gru->gs_asid_gen;
+ STAT(asid_new);
+ } else {
+ STAT(asid_reuse);
+ }
+
+ BUG_ON(asids->mt_ctxbitmap & ctxbitmap);
+ asids->mt_ctxbitmap |= ctxbitmap;
+ if (!test_bit(gru->gs_gid, gms->ms_asidmap))
+ __set_bit(gru->gs_gid, gms->ms_asidmap);
+ spin_unlock(&gms->ms_asid_lock);
+
+ gru_dbg(grudev,
+ "gru %x, gms %p, ctxnum 0x%d, asid 0x%x, asidmap 0x%lx\n",
+ gru->gs_gid, gms, ctxnum, asid, gms->ms_asidmap[0]);
+ return asid;
+}
+
+static void gru_unload_mm_tracker(struct gru_state *gru,
+ struct gru_mm_struct *gms, int ctxnum)
+{
+ struct gru_mm_tracker *asids;
+ unsigned short ctxbitmap;
+
+ asids = &gms->ms_asids[gru->gs_gid];
+ ctxbitmap = (1 << ctxnum);
+ spin_lock(&gms->ms_asid_lock);
+ BUG_ON((asids->mt_ctxbitmap & ctxbitmap) != ctxbitmap);
+ asids->mt_ctxbitmap ^= ctxbitmap;
+ gru_dbg(grudev, "gru %x, gms %p, ctxnum 0x%d, asidmap 0x%lx\n",
+ gru->gs_gid, gms, ctxnum, gms->ms_asidmap[0]);
+ spin_unlock(&gms->ms_asid_lock);
+}
+
+/*
+ * Decrement the reference count on a GTS structure. Free the structure
+ * if the reference count goes to zero.
+ */
+void gts_drop(struct gru_thread_state *gts)
+{
+ if (gts && atomic_dec_return(>s->ts_refcnt) == 0) {
+ gru_drop_mmu_notifier(gts->ts_gms);
+ kfree(gts);
+ STAT(gts_free);
+ }
+}
+
+/*
+ * Locate the GTS structure for the current thread.
+ */
+static struct gru_thread_state *gru_find_current_gts_nolock(struct gru_vma_data
+ *vdata, int tsid)
+{
+ struct gru_thread_state *gts;
+
+ list_for_each_entry(gts, &vdata->vd_head, ts_next)
+ if (gts->ts_tsid == tsid)
+ return gts;
+ return NULL;
+}
+
+/*
+ * Allocate a thread state structure.
+ */
+static struct gru_thread_state *gru_alloc_gts(struct vm_area_struct *vma,
+ struct gru_vma_data *vdata,
+ int tsid)
+{
+ struct gru_thread_state *gts;
+ int bytes;
+
+ bytes = DSR_BYTES(vdata->vd_dsr_au_count) +
+ CBR_BYTES(vdata->vd_cbr_au_count);
+ bytes += sizeof(struct gru_thread_state);
+ gts = kzalloc(bytes, GFP_KERNEL);
+ if (!gts)
+ return NULL;
+
+ STAT(gts_alloc);
+ atomic_set(>s->ts_refcnt, 1);
+ mutex_init(>s->ts_ctxlock);
+ gts->ts_cbr_au_count = vdata->vd_cbr_au_count;
+ gts->ts_dsr_au_count = vdata->vd_dsr_au_count;
+ gts->ts_user_options = vdata->vd_user_options;
+ gts->ts_tsid = tsid;
+ gts->ts_user_options = vdata->vd_user_options;
+ gts->ts_ctxnum = NULLCTX;
+ gts->ts_mm = current->mm;
+ gts->ts_vma = vma;
+ gts->ts_tlb_int_select = -1;
+ gts->ts_gms = gru_register_mmu_notifier();
+ if (!gts->ts_gms)
+ goto err;
+
+ gru_dbg(grudev, "alloc vdata %p, new gts %p\n", vdata, gts);
+ return gts;
+
+err:
+ gts_drop(gts);
+ return NULL;
+}
+
+/*
+ * Allocate a vma private data structure.
+ */
+struct gru_vma_data *gru_alloc_vma_data(struct vm_area_struct *vma, int tsid)
+{
+ struct gru_vma_data *vdata = NULL;
+
+ vdata = kmalloc(sizeof(*vdata), GFP_KERNEL);
+ if (!vdata)
+ return NULL;
+
+ INIT_LIST_HEAD(&vdata->vd_head);
+ spin_lock_init(&vdata->vd_lock);
+ gru_dbg(grudev, "alloc vdata %p\n", vdata);
+ return vdata;
+}
+
+/*
+ * Find the thread state structure for the current thread.
+ */
+struct gru_thread_state *gru_find_thread_state(struct vm_area_struct *vma,
+ int tsid)
+{
+ struct gru_vma_data *vdata = vma->vm_private_data;
+ struct gru_thread_state *gts;
+
+ spin_lock(&vdata->vd_lock);
+ gts = gru_find_current_gts_nolock(vdata, tsid);
+ spin_unlock(&vdata->vd_lock);
+ gru_dbg(grudev, "vma %p, gts %p\n", vma, gts);
+ return gts;
+}
+
+/*
+ * Allocate a new thread state for a GSEG. Note that races may allow
+ * another thread to race to create a gts.
+ */
+struct gru_thread_state *gru_alloc_thread_state(struct vm_area_struct *vma,
+ int tsid)
+{
+ struct gru_vma_data *vdata = vma->vm_private_data;
+ struct gru_thread_state *gts, *ngts;
+
+ gts = gru_alloc_gts(vma, vdata, tsid);
+ if (!gts)
+ return NULL;
+
+ spin_lock(&vdata->vd_lock);
+ ngts = gru_find_current_gts_nolock(vdata, tsid);
+ if (ngts) {
+ gts_drop(gts);
+ gts = ngts;
+ STAT(gts_double_allocate);
+ } else {
+ list_add(>s->ts_next, &vdata->vd_head);
+ }
+ spin_unlock(&vdata->vd_lock);
+ gru_dbg(grudev, "vma %p, gts %p\n", vma, gts);
+ return gts;
+}
+
+/*
+ * Free the GRU context assigned to the thread state.
+ */
+static void gru_free_gru_context(struct gru_thread_state *gts)
+{
+ struct gru_state *gru;
+
+ gru = gts->ts_gru;
+ gru_dbg(grudev, "gts %p, gru %p\n", gts, gru);
+
+ spin_lock(&gru->gs_lock);
+ gru->gs_gts[gts->ts_ctxnum] = NULL;
+ free_gru_resources(gru, gts);
+ BUG_ON(test_bit(gts->ts_ctxnum, &gru->gs_context_map) == 0);
+ __clear_bit(gts->ts_ctxnum, &gru->gs_context_map);
+ gts->ts_ctxnum = NULLCTX;
+ gts->ts_gru = NULL;
+ spin_unlock(&gru->gs_lock);
+
+ gts_drop(gts);
+ STAT(free_context);
+}
+
+/*
+ * Prefetching cachelines help hardware performance.
+ * (Strictly a performance enhancement. Not functionally required).
+ */
+static void prefetch_data(void *p, int num, int stride)
+{
+ while (num-- > 0) {
+ prefetchw(p);
+ p += stride;
+ }
+}
+
+static inline long gru_copy_handle(void *d, void *s)
+{
+ memcpy(d, s, GRU_HANDLE_BYTES);
+ return GRU_HANDLE_BYTES;
+}
+
+/* rewrite in assembly & use lots of prefetch */
+static void gru_load_context_data(void *save, void *grubase, int ctxnum,
+ unsigned long cbrmap, unsigned long dsrmap)
+{
+ void *gseg, *cb, *cbe;
+ unsigned long length;
+ int i, scr;
+
+ gseg = grubase + ctxnum * GRU_GSEG_STRIDE;
+ length = hweight64(dsrmap) * GRU_DSR_AU_BYTES;
+ prefetch_data(gseg + GRU_DS_BASE, length / GRU_CACHE_LINE_BYTES,
+ GRU_CACHE_LINE_BYTES);
+
+ cb = gseg + GRU_CB_BASE;
+ cbe = grubase + GRU_CBE_BASE;
+ for_each_cbr_in_allocation_map(i, &cbrmap, scr) {
+ prefetch_data(cb, 1, GRU_CACHE_LINE_BYTES);
+ prefetch_data(cbe + i * GRU_HANDLE_STRIDE, 1,
+ GRU_CACHE_LINE_BYTES);
+ cb += GRU_HANDLE_STRIDE;
+ }
+
+ cb = gseg + GRU_CB_BASE;
+ for_each_cbr_in_allocation_map(i, &cbrmap, scr) {
+ save += gru_copy_handle(cb, save);
+ save += gru_copy_handle(cbe + i * GRU_HANDLE_STRIDE, save);
+ cb += GRU_HANDLE_STRIDE;
+ }
+
+ memcpy(gseg + GRU_DS_BASE, save, length);
+}
+
+static void gru_unload_context_data(void *save, void *grubase, int ctxnum,
+ unsigned long cbrmap, unsigned long dsrmap)
+{
+ void *gseg, *cb, *cbe;
+ unsigned long length;
+ int i, scr;
+
+ gseg = grubase + ctxnum * GRU_GSEG_STRIDE;
+
+ cb = gseg + GRU_CB_BASE;
+ cbe = grubase + GRU_CBE_BASE;
+ for_each_cbr_in_allocation_map(i, &cbrmap, scr) {
+ save += gru_copy_handle(save, cb);
+ save += gru_copy_handle(save, cbe + i * GRU_HANDLE_STRIDE);
+ cb += GRU_HANDLE_STRIDE;
+ }
+ length = hweight64(dsrmap) * GRU_DSR_AU_BYTES;
+ memcpy(save, gseg + GRU_DS_BASE, length);
+}
+
+void gru_unload_context(struct gru_thread_state *gts, int savestate)
+{
+ struct gru_state *gru = gts->ts_gru;
+ struct gru_context_configuration_handle *cch;
+ int ctxnum = gts->ts_ctxnum;
+
+ zap_vma_ptes(gts->ts_vma, UGRUADDR(gts), GRU_GSEG_PAGESIZE);
+ cch = get_cch(gru->gs_gru_base_vaddr, ctxnum);
+
+ lock_cch_handle(cch);
+ if (cch_interrupt_sync(cch))
+ BUG();
+ gru_dbg(grudev, "gts %p\n", gts);
+
+ gru_unload_mm_tracker(gru, gts->ts_gms, gts->ts_ctxnum);
+ if (savestate)
+ gru_unload_context_data(gts->ts_gdata, gru->gs_gru_base_vaddr,
+ ctxnum, gts->ts_cbr_map,
+ gts->ts_dsr_map);
+
+ if (cch_deallocate(cch))
+ BUG();
+ gts->ts_force_unload = 0; /* ts_force_unload locked by CCH lock */
+ unlock_cch_handle(cch);
+
+ gru_free_gru_context(gts);
+ STAT(unload_context);
+}
+
+/*
+ * Load a GRU context by copying it from the thread data structure in memory
+ * to the GRU.
+ */
+static void gru_load_context(struct gru_thread_state *gts)
+{
+ struct gru_state *gru = gts->ts_gru;
+ struct gru_context_configuration_handle *cch;
+ int err, asid, ctxnum = gts->ts_ctxnum;
+
+ gru_dbg(grudev, "gts %p\n", gts);
+ cch = get_cch(gru->gs_gru_base_vaddr, ctxnum);
+
+ lock_cch_handle(cch);
+ asid = gru_load_mm_tracker(gru, gts->ts_gms, gts->ts_ctxnum);
+ cch->tfm_fault_bit_enable =
+ (gts->ts_user_options == GRU_OPT_MISS_FMM_POLL
+ || gts->ts_user_options == GRU_OPT_MISS_FMM_INTR);
+ cch->tlb_int_enable = (gts->ts_user_options == GRU_OPT_MISS_FMM_INTR);
+ if (cch->tlb_int_enable) {
+ gts->ts_tlb_int_select = gru_cpu_fault_map_id();
+ cch->tlb_int_select = gts->ts_tlb_int_select;
+ }
+ cch->tfm_done_bit_enable = 0;
+ err = cch_allocate(cch, asid, gts->ts_cbr_map, gts->ts_dsr_map);
+ if (err) {
+ gru_dbg(grudev,
+ "err %d: cch %p, gts %p, cbr 0x%lx, dsr 0x%lx\n",
+ err, cch, gts, gts->ts_cbr_map, gts->ts_dsr_map);
+ BUG();
+ }
+
+ gru_load_context_data(gts->ts_gdata, gru->gs_gru_base_vaddr, ctxnum,
+ gts->ts_cbr_map, gts->ts_dsr_map);
+
+ if (cch_start(cch))
+ BUG();
+ unlock_cch_handle(cch);
+
+ STAT(load_context);
+}
+
+/*
+ * Update fields in an active CCH:
+ * - retarget interrupts on local blade
+ * - force a delayed context unload by clearing the CCH asids. This
+ * forces TLB misses for new GRU instructions. The context is unloaded
+ * when the next TLB miss occurs.
+ */
+static int gru_update_cch(struct gru_thread_state *gts, int int_select)
+{
+ struct gru_context_configuration_handle *cch;
+ struct gru_state *gru = gts->ts_gru;
+ int i, ctxnum = gts->ts_ctxnum, ret = 0;
+
+ cch = get_cch(gru->gs_gru_base_vaddr, ctxnum);
+
+ lock_cch_handle(cch);
+ if (cch->state == CCHSTATE_ACTIVE) {
+ if (gru->gs_gts[gts->ts_ctxnum] != gts)
+ goto exit;
+ if (cch_interrupt(cch))
+ BUG();
+ if (int_select >= 0) {
+ gts->ts_tlb_int_select = int_select;
+ cch->tlb_int_select = int_select;
+ } else {
+ for (i = 0; i < 8; i++)
+ cch->asid[i] = 0;
+ cch->tfm_fault_bit_enable = 0;
+ cch->tlb_int_enable = 0;
+ gts->ts_force_unload = 1;
+ }
+ if (cch_start(cch))
+ BUG();
+ ret = 1;
+ }
+exit:
+ unlock_cch_handle(cch);
+ return ret;
+}
+
+/*
+ * Update CCH tlb interrupt select. Required when all the following is true:
+ * - task's GRU context is loaded into a GRU
+ * - task is using interrupt notification for TLB faults
+ * - task has migrated to a different cpu on the same blade where
+ * it was previously running.
+ */
+static int gru_retarget_intr(struct gru_thread_state *gts)
+{
+ if (gts->ts_tlb_int_select < 0
+ || gts->ts_tlb_int_select == gru_cpu_fault_map_id())
+ return 0;
+
+ gru_dbg(grudev, "retarget from %d to %d\n", gts->ts_tlb_int_select,
+ gru_cpu_fault_map_id());
+ return gru_update_cch(gts, gru_cpu_fault_map_id());
+}
+
+
+/*
+ * Insufficient GRU resources available on the local blade. Steal a context from
+ * a process. This is a hack until a _real_ resource scheduler is written....
+ */
+#define next_ctxnum(n) ((n) < GRU_NUM_CCH - 2 ? (n) + 1 : 0)
+#define next_gru(b, g) (((g) < &(b)->bs_grus[GRU_CHIPLETS_PER_BLADE - 1]) ? \
+ ((g)+1) : &(b)->bs_grus[0])
+
+static void gru_steal_context(struct gru_thread_state *gts)
+{
+ struct gru_blade_state *blade;
+ struct gru_state *gru, *gru0;
+ struct gru_thread_state *ngts = NULL;
+ int ctxnum, ctxnum0, flag = 0, cbr, dsr;
+
+ cbr = gts->ts_cbr_au_count;
+ dsr = gts->ts_dsr_au_count;
+
+ preempt_disable();
+ blade = gru_base[uv_numa_blade_id()];
+ spin_lock(&blade->bs_lock);
+
+ ctxnum = next_ctxnum(blade->bs_lru_ctxnum);
+ gru = blade->bs_lru_gru;
+ if (ctxnum == 0)
+ gru = next_gru(blade, gru);
+ ctxnum0 = ctxnum;
+ gru0 = gru;
+ while (1) {
+ if (check_gru_resources(gru, cbr, dsr, GRU_NUM_CCH))
+ break;
+ spin_lock(&gru->gs_lock);
+ for (; ctxnum < GRU_NUM_CCH; ctxnum++) {
+ if (flag && gru == gru0 && ctxnum == ctxnum0)
+ break;
+ ngts = gru->gs_gts[ctxnum];
+ /*
+ * We are grabbing locks out of order, so trylock is
+ * needed. GTSs are usually not locked, so the odds of
+ * success are high. If trylock fails, try to steal a
+ * different GSEG.
+ */
+ if (ngts && mutex_trylock(&ngts->ts_ctxlock))
+ break;
+ ngts = NULL;
+ flag = 1;
+ }
+ spin_unlock(&gru->gs_lock);
+ if (ngts || (flag && gru == gru0 && ctxnum == ctxnum0))
+ break;
+ ctxnum = 0;
+ gru = next_gru(blade, gru);
+ }
+ blade->bs_lru_gru = gru;
+ blade->bs_lru_ctxnum = ctxnum;
+ spin_unlock(&blade->bs_lock);
+ preempt_enable();
+
+ if (ngts) {
+ STAT(steal_context);
+ ngts->ts_steal_jiffies = jiffies;
+ gru_unload_context(ngts, 1);
+ mutex_unlock(&ngts->ts_ctxlock);
+ } else {
+ STAT(steal_context_failed);
+ }
+ gru_dbg(grudev,
+ "stole gru %x, ctxnum %d from gts %p. Need cb %d, ds %d;"
+ " avail cb %ld, ds %ld\n",
+ gru->gs_gid, ctxnum, ngts, cbr, dsr, hweight64(gru->gs_cbr_map),
+ hweight64(gru->gs_dsr_map));
+}
+
+/*
+ * Scan the GRUs on the local blade & assign a GRU context.
+ */
+static struct gru_state *gru_assign_gru_context(struct gru_thread_state *gts)
+{
+ struct gru_state *gru, *grux;
+ int i, max_active_contexts;
+
+ preempt_disable();
+
+again:
+ gru = NULL;
+ max_active_contexts = GRU_NUM_CCH;
+ for_each_gru_on_blade(grux, uv_numa_blade_id(), i) {
+ if (check_gru_resources(grux, gts->ts_cbr_au_count,
+ gts->ts_dsr_au_count,
+ max_active_contexts)) {
+ gru = grux;
+ max_active_contexts = grux->gs_active_contexts;
+ if (max_active_contexts == 0)
+ break;
+ }
+ }
+
+ if (gru) {
+ spin_lock(&gru->gs_lock);
+ if (!check_gru_resources(gru, gts->ts_cbr_au_count,
+ gts->ts_dsr_au_count, GRU_NUM_CCH)) {
+ spin_unlock(&gru->gs_lock);
+ goto again;
+ }
+ reserve_gru_resources(gru, gts);
+ gts->ts_gru = gru;
+ gts->ts_ctxnum =
+ find_first_zero_bit(&gru->gs_context_map, GRU_NUM_CCH);
+ BUG_ON(gts->ts_ctxnum == GRU_NUM_CCH);
+ atomic_inc(>s->ts_refcnt);
+ gru->gs_gts[gts->ts_ctxnum] = gts;
+ __set_bit(gts->ts_ctxnum, &gru->gs_context_map);
+ spin_unlock(&gru->gs_lock);
+
+ STAT(assign_context);
+ gru_dbg(grudev,
+ "gseg %p, gts %p, gru %x, ctx %d, cbr %d, dsr %d\n",
+ gseg_virtual_address(gts->ts_gru, gts->ts_ctxnum), gts,
+ gts->ts_gru->gs_gid, gts->ts_ctxnum,
+ gts->ts_cbr_au_count, gts->ts_dsr_au_count);
+ } else {
+ gru_dbg(grudev, "failed to allocate a GTS %s\n", "");
+ STAT(assign_context_failed);
+ }
+
+ preempt_enable();
+ return gru;
+}
+
+/*
+ * gru_nopage
+ *
+ * Map the user's GRU segment
+ *
+ * Note: gru segments alway mmaped on GRU_GSEG_PAGESIZE boundaries.
+ */
+int gru_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
+{
+ struct gru_thread_state *gts;
+ unsigned long paddr, vaddr;
+
+ vaddr = (unsigned long)vmf->virtual_address;
+ gru_dbg(grudev, "vma %p, vaddr 0x%lx (0x%lx)\n",
+ vma, vaddr, GSEG_BASE(vaddr));
+ STAT(nopfn);
+
+ /* The following check ensures vaddr is a valid address in the VMA */
+ gts = gru_find_thread_state(vma, TSID(vaddr, vma));
+ if (!gts)
+ return VM_FAULT_SIGBUS;
+
+again:
+ preempt_disable();
+ mutex_lock(>s->ts_ctxlock);
+ if (gts->ts_gru) {
+ if (gts->ts_gru->gs_blade_id != uv_numa_blade_id()) {
+ STAT(migrated_nopfn_unload);
+ gru_unload_context(gts, 1);
+ } else {
+ if (gru_retarget_intr(gts))
+ STAT(migrated_nopfn_retarget);
+ }
+ }
+
+ if (!gts->ts_gru) {
+ if (!gru_assign_gru_context(gts)) {
+ mutex_unlock(>s->ts_ctxlock);
+ preempt_enable();
+ schedule_timeout(GRU_ASSIGN_DELAY); /* true hack ZZZ */
+ if (gts->ts_steal_jiffies + GRU_STEAL_DELAY < jiffies)
+ gru_steal_context(gts);
+ goto again;
+ }
+ gru_load_context(gts);
+ paddr = gseg_physical_address(gts->ts_gru, gts->ts_ctxnum);
+ remap_pfn_range(vma, vaddr & ~(GRU_GSEG_PAGESIZE - 1),
+ paddr >> PAGE_SHIFT, GRU_GSEG_PAGESIZE,
+ vma->vm_page_prot);
+ }
+
+ mutex_unlock(>s->ts_ctxlock);
+ preempt_enable();
+
+ return VM_FAULT_NOPAGE;
+}
+
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * PROC INTERFACES
+ *
+ * This file supports the /proc interfaces for the GRU driver
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/proc_fs.h>
+#include <linux/device.h>
+#include <linux/seq_file.h>
+#include <linux/uaccess.h>
+#include "gru.h"
+#include "grulib.h"
+#include "grutables.h"
+
+#define printstat(s, f) printstat_val(s, &gru_stats.f, #f)
+
+static void printstat_val(struct seq_file *s, atomic_long_t *v, char *id)
+{
+ unsigned long val = atomic_long_read(v);
+
+ if (val)
+ seq_printf(s, "%16lu %s\n", val, id);
+}
+
+static int statistics_show(struct seq_file *s, void *p)
+{
+ printstat(s, vdata_alloc);
+ printstat(s, vdata_free);
+ printstat(s, gts_alloc);
+ printstat(s, gts_free);
+ printstat(s, vdata_double_alloc);
+ printstat(s, gts_double_allocate);
+ printstat(s, assign_context);
+ printstat(s, assign_context_failed);
+ printstat(s, free_context);
+ printstat(s, load_context);
+ printstat(s, unload_context);
+ printstat(s, steal_context);
+ printstat(s, steal_context_failed);
+ printstat(s, nopfn);
+ printstat(s, break_cow);
+ printstat(s, asid_new);
+ printstat(s, asid_next);
+ printstat(s, asid_wrap);
+ printstat(s, asid_reuse);
+ printstat(s, intr);
+ printstat(s, call_os);
+ printstat(s, call_os_check_for_bug);
+ printstat(s, call_os_wait_queue);
+ printstat(s, user_flush_tlb);
+ printstat(s, user_unload_context);
+ printstat(s, user_exception);
+ printstat(s, set_task_slice);
+ printstat(s, migrate_check);
+ printstat(s, migrated_retarget);
+ printstat(s, migrated_unload);
+ printstat(s, migrated_unload_delay);
+ printstat(s, migrated_nopfn_retarget);
+ printstat(s, migrated_nopfn_unload);
+ printstat(s, tlb_dropin);
+ printstat(s, tlb_dropin_fail_no_asid);
+ printstat(s, tlb_dropin_fail_upm);
+ printstat(s, tlb_dropin_fail_invalid);
+ printstat(s, tlb_dropin_fail_range_active);
+ printstat(s, tlb_dropin_fail_idle);
+ printstat(s, tlb_dropin_fail_fmm);
+ printstat(s, mmu_invalidate_range);
+ printstat(s, mmu_invalidate_page);
+ printstat(s, mmu_clear_flush_young);
+ printstat(s, flush_tlb);
+ printstat(s, flush_tlb_gru);
+ printstat(s, flush_tlb_gru_tgh);
+ printstat(s, flush_tlb_gru_zero_asid);
+ printstat(s, copy_gpa);
+ printstat(s, mesq_receive);
+ printstat(s, mesq_receive_none);
+ printstat(s, mesq_send);
+ printstat(s, mesq_send_failed);
+ printstat(s, mesq_noop);
+ printstat(s, mesq_send_unexpected_error);
+ printstat(s, mesq_send_lb_overflow);
+ printstat(s, mesq_send_qlimit_reached);
+ printstat(s, mesq_send_amo_nacked);
+ printstat(s, mesq_send_put_nacked);
+ printstat(s, mesq_qf_not_full);
+ printstat(s, mesq_qf_locked);
+ printstat(s, mesq_qf_noop_not_full);
+ printstat(s, mesq_qf_switch_head_failed);
+ printstat(s, mesq_qf_unexpected_error);
+ printstat(s, mesq_noop_unexpected_error);
+ printstat(s, mesq_noop_lb_overflow);
+ printstat(s, mesq_noop_qlimit_reached);
+ printstat(s, mesq_noop_amo_nacked);
+ printstat(s, mesq_noop_put_nacked);
+ return 0;
+}
+
+static ssize_t statistics_write(struct file *file, const char __user *userbuf,
+ size_t count, loff_t *data)
+{
+ memset(&gru_stats, 0, sizeof(gru_stats));
+ return count;
+}
+
+static int options_show(struct seq_file *s, void *p)
+{
+ seq_printf(s, "0x%lx\n", gru_options);
+ return 0;
+}
+
+static ssize_t options_write(struct file *file, const char __user *userbuf,
+ size_t count, loff_t *data)
+{
+ unsigned long val;
+ char buf[80];
+
+ if (copy_from_user
+ (buf, userbuf, count < sizeof(buf) ? count : sizeof(buf)))
+ return -EFAULT;
+ if (!strict_strtoul(buf, 10, &val))
+ gru_options = val;
+
+ return count;
+}
+
+static int cch_seq_show(struct seq_file *file, void *data)
+{
+ long gid = *(long *)data;
+ int i;
+ struct gru_state *gru = GID_TO_GRU(gid);
+ struct gru_thread_state *ts;
+ const char *mode[] = { "??", "UPM", "INTR", "OS_POLL" };
+
+ if (gid == 0)
+ seq_printf(file, "#%5s%5s%6s%9s%6s%8s%8s\n", "gid", "bid",
+ "ctx#", "pid", "cbrs", "dsbytes", "mode");
+ if (gru)
+ for (i = 0; i < GRU_NUM_CCH; i++) {
+ ts = gru->gs_gts[i];
+ if (!ts)
+ continue;
+ seq_printf(file, " %5d%5d%6d%9d%6d%8d%8s\n",
+ gru->gs_gid, gru->gs_blade_id, i,
+ ts->ts_tgid_owner,
+ ts->ts_cbr_au_count * GRU_CBR_AU_SIZE,
+ ts->ts_cbr_au_count * GRU_DSR_AU_BYTES,
+ mode[ts->ts_user_options &
+ GRU_OPT_MISS_MASK]);
+ }
+
+ return 0;
+}
+
+static int gru_seq_show(struct seq_file *file, void *data)
+{
+ long gid = *(long *)data, ctxfree, cbrfree, dsrfree;
+ struct gru_state *gru = GID_TO_GRU(gid);
+
+ if (gid == 0) {
+ seq_printf(file, "#%5s%5s%7s%6s%6s%8s%6s%6s\n", "gid", "nid",
+ "ctx", "cbr", "dsr", "ctx", "cbr", "dsr");
+ seq_printf(file, "#%5s%5s%7s%6s%6s%8s%6s%6s\n", "", "", "busy",
+ "busy", "busy", "free", "free", "free");
+ }
+ if (gru) {
+ ctxfree = GRU_NUM_CCH - gru->gs_active_contexts;
+ cbrfree = hweight64(gru->gs_cbr_map) * GRU_CBR_AU_SIZE;
+ dsrfree = hweight64(gru->gs_dsr_map) * GRU_DSR_AU_BYTES;
+ seq_printf(file, " %5d%5d%7ld%6ld%6ld%8ld%6ld%6ld\n",
+ gru->gs_gid, gru->gs_blade_id, GRU_NUM_CCH - ctxfree,
+ GRU_NUM_CBE - cbrfree, GRU_NUM_DSR_BYTES - dsrfree,
+ ctxfree, cbrfree, dsrfree);
+ }
+
+ return 0;
+}
+
+static void seq_stop(struct seq_file *file, void *data)
+{
+}
+
+static void *seq_start(struct seq_file *file, loff_t *gid)
+{
+ if (*gid < GRU_MAX_GRUS)
+ return gid;
+ return NULL;
+}
+
+static void *seq_next(struct seq_file *file, void *data, loff_t *gid)
+{
+ (*gid)++;
+ if (*gid < GRU_MAX_GRUS)
+ return gid;
+ return NULL;
+}
+
+static const struct seq_operations cch_seq_ops = {
+ .start = seq_start,
+ .next = seq_next,
+ .stop = seq_stop,
+ .show = cch_seq_show
+};
+
+static const struct seq_operations gru_seq_ops = {
+ .start = seq_start,
+ .next = seq_next,
+ .stop = seq_stop,
+ .show = gru_seq_show
+};
+
+static int statistics_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, statistics_show, NULL);
+}
+
+static int options_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, options_show, NULL);
+}
+
+static int cch_open(struct inode *inode, struct file *file)
+{
+ return seq_open(file, &cch_seq_ops);
+}
+
+static int gru_open(struct inode *inode, struct file *file)
+{
+ return seq_open(file, &gru_seq_ops);
+}
+
+/* *INDENT-OFF* */
+static const struct file_operations statistics_fops = {
+ .open = statistics_open,
+ .read = seq_read,
+ .write = statistics_write,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations options_fops = {
+ .open = options_open,
+ .read = seq_read,
+ .write = options_write,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static const struct file_operations cch_fops = {
+ .open = cch_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = seq_release,
+};
+static const struct file_operations gru_fops = {
+ .open = gru_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = seq_release,
+};
+
+static struct proc_entry {
+ char *name;
+ int mode;
+ const struct file_operations *fops;
+ struct proc_dir_entry *entry;
+} proc_files[] = {
+ {"statistics", 0644, &statistics_fops},
+ {"debug_options", 0644, &options_fops},
+ {"cch_status", 0444, &cch_fops},
+ {"gru_status", 0444, &gru_fops},
+ {NULL}
+};
+/* *INDENT-ON* */
+
+static struct proc_dir_entry *proc_gru __read_mostly;
+
+static int create_proc_file(struct proc_entry *p)
+{
+ p->entry = create_proc_entry(p->name, p->mode, proc_gru);
+ if (!p->entry)
+ return -1;
+ p->entry->proc_fops = p->fops;
+ return 0;
+}
+
+static void delete_proc_files(void)
+{
+ struct proc_entry *p;
+
+ if (proc_gru) {
+ for (p = proc_files; p->name; p++)
+ if (p->entry)
+ remove_proc_entry(p->name, proc_gru);
+ remove_proc_entry("gru", NULL);
+ }
+}
+
+int gru_proc_init(void)
+{
+ struct proc_entry *p;
+
+ proc_mkdir("sgi_uv", NULL);
+ proc_gru = proc_mkdir("sgi_uv/gru", NULL);
+
+ for (p = proc_files; p->name; p++)
+ if (create_proc_file(p))
+ goto err;
+ return 0;
+
+err:
+ delete_proc_files();
+ return -1;
+}
+
+void gru_proc_exit(void)
+{
+ delete_proc_files();
+}
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * GRU DRIVER TABLES, MACROS, externs, etc
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __GRUTABLES_H__
+#define __GRUTABLES_H__
+
+/*
+ * GRU Chiplet:
+ * The GRU is a user addressible memory accelerator. It provides
+ * several forms of load, store, memset, bcopy instructions. In addition, it
+ * contains special instructions for AMOs, sending messages to message
+ * queues, etc.
+ *
+ * The GRU is an integral part of the node controller. It connects
+ * directly to the cpu socket. In its current implementation, there are 2
+ * GRU chiplets in the node controller on each blade (~node).
+ *
+ * The entire GRU memory space is fully coherent and cacheable by the cpus.
+ *
+ * Each GRU chiplet has a physical memory map that looks like the following:
+ *
+ * +-----------------+
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * |/////////////////|
+ * +-----------------+
+ * | system control |
+ * +-----------------+ _______ +-------------+
+ * |/////////////////| / | |
+ * |/////////////////| / | |
+ * |/////////////////| / | instructions|
+ * |/////////////////| / | |
+ * |/////////////////| / | |
+ * |/////////////////| / |-------------|
+ * |/////////////////| / | |
+ * +-----------------+ | |
+ * | context 15 | | data |
+ * +-----------------+ | |
+ * | ...... | \ | |
+ * +-----------------+ \____________ +-------------+
+ * | context 1 |
+ * +-----------------+
+ * | context 0 |
+ * +-----------------+
+ *
+ * Each of the "contexts" is a chunk of memory that can be mmaped into user
+ * space. The context consists of 2 parts:
+ *
+ * - an instruction space that can be directly accessed by the user
+ * to issue GRU instructions and to check instruction status.
+ *
+ * - a data area that acts as normal RAM.
+ *
+ * User instructions contain virtual addresses of data to be accessed by the
+ * GRU. The GRU contains a TLB that is used to convert these user virtual
+ * addresses to physical addresses.
+ *
+ * The "system control" area of the GRU chiplet is used by the kernel driver
+ * to manage user contexts and to perform functions such as TLB dropin and
+ * purging.
+ *
+ * One context may be reserved for the kernel and used for cross-partition
+ * communication. The GRU will also be used to asynchronously zero out
+ * large blocks of memory (not currently implemented).
+ *
+ *
+ * Tables:
+ *
+ * VDATA-VMA Data - Holds a few parameters. Head of linked list of
+ * GTS tables for threads using the GSEG
+ * GTS - Gru Thread State - contains info for managing a GSEG context. A
+ * GTS is allocated for each thread accessing a
+ * GSEG.
+ * GTD - GRU Thread Data - contains shadow copy of GRU data when GSEG is
+ * not loaded into a GRU
+ * GMS - GRU Memory Struct - Used to manage TLB shootdowns. Tracks GRUs
+ * where a GSEG has been loaded. Similar to
+ * an mm_struct but for GRU.
+ *
+ * GS - GRU State - Used to manage the state of a GRU chiplet
+ * BS - Blade State - Used to manage state of all GRU chiplets
+ * on a blade
+ *
+ *
+ * Normal task tables for task using GRU.
+ * - 2 threads in process
+ * - 2 GSEGs open in process
+ * - GSEG1 is being used by both threads
+ * - GSEG2 is used only by thread 2
+ *
+ * task -->|
+ * task ---+---> mm ->------ (notifier) -------+-> gms
+ * | |
+ * |--> vma -> vdata ---> gts--->| GSEG1 (thread1)
+ * | | |
+ * | +-> gts--->| GSEG1 (thread2)
+ * | |
+ * |--> vma -> vdata ---> gts--->| GSEG2 (thread2)
+ * .
+ * .
+ *
+ * GSEGs are marked DONTCOPY on fork
+ *
+ * At open
+ * file.private_data -> NULL
+ *
+ * At mmap,
+ * vma -> vdata
+ *
+ * After gseg reference
+ * vma -> vdata ->gts
+ *
+ * After fork
+ * parent
+ * vma -> vdata -> gts
+ * child
+ * (vma is not copied)
+ *
+ */
+
+#include <linux/rmap.h>
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/wait.h>
+#include <linux/mmu_notifier.h>
+#include "gru.h"
+#include "gruhandles.h"
+
+extern struct gru_stats_s gru_stats;
+extern struct gru_blade_state *gru_base[];
+extern unsigned long gru_start_paddr, gru_end_paddr;
+
+#define GRU_MAX_BLADES MAX_NUMNODES
+#define GRU_MAX_GRUS (GRU_MAX_BLADES * GRU_CHIPLETS_PER_BLADE)
+
+#define GRU_DRIVER_ID_STR "SGI GRU Device Driver"
+#define GRU_DRIVER_VERSION_STR "0.80"
+
+/*
+ * GRU statistics.
+ */
+struct gru_stats_s {
+ atomic_long_t vdata_alloc;
+ atomic_long_t vdata_free;
+ atomic_long_t gts_alloc;
+ atomic_long_t gts_free;
+ atomic_long_t vdata_double_alloc;
+ atomic_long_t gts_double_allocate;
+ atomic_long_t assign_context;
+ atomic_long_t assign_context_failed;
+ atomic_long_t free_context;
+ atomic_long_t load_context;
+ atomic_long_t unload_context;
+ atomic_long_t steal_context;
+ atomic_long_t steal_context_failed;
+ atomic_long_t nopfn;
+ atomic_long_t break_cow;
+ atomic_long_t asid_new;
+ atomic_long_t asid_next;
+ atomic_long_t asid_wrap;
+ atomic_long_t asid_reuse;
+ atomic_long_t intr;
+ atomic_long_t call_os;
+ atomic_long_t call_os_check_for_bug;
+ atomic_long_t call_os_wait_queue;
+ atomic_long_t user_flush_tlb;
+ atomic_long_t user_unload_context;
+ atomic_long_t user_exception;
+ atomic_long_t set_task_slice;
+ atomic_long_t migrate_check;
+ atomic_long_t migrated_retarget;
+ atomic_long_t migrated_unload;
+ atomic_long_t migrated_unload_delay;
+ atomic_long_t migrated_nopfn_retarget;
+ atomic_long_t migrated_nopfn_unload;
+ atomic_long_t tlb_dropin;
+ atomic_long_t tlb_dropin_fail_no_asid;
+ atomic_long_t tlb_dropin_fail_upm;
+ atomic_long_t tlb_dropin_fail_invalid;
+ atomic_long_t tlb_dropin_fail_range_active;
+ atomic_long_t tlb_dropin_fail_idle;
+ atomic_long_t tlb_dropin_fail_fmm;
+ atomic_long_t mmu_invalidate_range;
+ atomic_long_t mmu_invalidate_page;
+ atomic_long_t mmu_clear_flush_young;
+ atomic_long_t flush_tlb;
+ atomic_long_t flush_tlb_gru;
+ atomic_long_t flush_tlb_gru_tgh;
+ atomic_long_t flush_tlb_gru_zero_asid;
+
+ atomic_long_t copy_gpa;
+
+ atomic_long_t mesq_receive;
+ atomic_long_t mesq_receive_none;
+ atomic_long_t mesq_send;
+ atomic_long_t mesq_send_failed;
+ atomic_long_t mesq_noop;
+ atomic_long_t mesq_send_unexpected_error;
+ atomic_long_t mesq_send_lb_overflow;
+ atomic_long_t mesq_send_qlimit_reached;
+ atomic_long_t mesq_send_amo_nacked;
+ atomic_long_t mesq_send_put_nacked;
+ atomic_long_t mesq_qf_not_full;
+ atomic_long_t mesq_qf_locked;
+ atomic_long_t mesq_qf_noop_not_full;
+ atomic_long_t mesq_qf_switch_head_failed;
+ atomic_long_t mesq_qf_unexpected_error;
+ atomic_long_t mesq_noop_unexpected_error;
+ atomic_long_t mesq_noop_lb_overflow;
+ atomic_long_t mesq_noop_qlimit_reached;
+ atomic_long_t mesq_noop_amo_nacked;
+ atomic_long_t mesq_noop_put_nacked;
+
+};
+
+#define OPT_DPRINT 1
+#define OPT_STATS 2
+#define GRU_QUICKLOOK 4
+
+
+#define IRQ_GRU 110 /* Starting IRQ number for interrupts */
+
+/* Delay in jiffies between attempts to assign a GRU context */
+#define GRU_ASSIGN_DELAY ((HZ * 20) / 1000)
+
+/*
+ * If a process has it's context stolen, min delay in jiffies before trying to
+ * steal a context from another process.
+ */
+#define GRU_STEAL_DELAY ((HZ * 200) / 1000)
+
+#define STAT(id) do { \
+ if (gru_options & OPT_STATS) \
+ atomic_long_inc(&gru_stats.id); \
+ } while (0)
+
+#ifdef CONFIG_SGI_GRU_DEBUG
+#define gru_dbg(dev, fmt, x...) \
+ do { \
+ if (gru_options & OPT_DPRINT) \
+ dev_dbg(dev, "%s: " fmt, __func__, x); \
+ } while (0)
+#else
+#define gru_dbg(x...)
+#endif
+
+/*-----------------------------------------------------------------------------
+ * ASID management
+ */
+#define MAX_ASID 0xfffff0
+#define MIN_ASID 8
+#define ASID_INC 8 /* number of regions */
+
+/* Generate a GRU asid value from a GRU base asid & a virtual address. */
+#if defined CONFIG_IA64
+#define VADDR_HI_BIT 64
+#define GRUREGION(addr) ((addr) >> (VADDR_HI_BIT - 3) & 3)
+#elif defined __x86_64
+#define VADDR_HI_BIT 48
+#define GRUREGION(addr) (0) /* ZZZ could do better */
+#else
+#error "Unsupported architecture"
+#endif
+#define GRUASID(asid, addr) ((asid) + GRUREGION(addr))
+
+/*------------------------------------------------------------------------------
+ * File & VMS Tables
+ */
+
+struct gru_state;
+
+/*
+ * This structure is pointed to from the mmstruct via the notifier pointer.
+ * There is one of these per address space.
+ */
+struct gru_mm_tracker {
+ unsigned int mt_asid_gen; /* ASID wrap count */
+ int mt_asid; /* current base ASID for gru */
+ unsigned short mt_ctxbitmap; /* bitmap of contexts using
+ asid */
+};
+
+struct gru_mm_struct {
+ struct mmu_notifier ms_notifier;
+ atomic_t ms_refcnt;
+ spinlock_t ms_asid_lock; /* protects ASID assignment */
+ atomic_t ms_range_active;/* num range_invals active */
+ char ms_released;
+ wait_queue_head_t ms_wait_queue;
+ DECLARE_BITMAP(ms_asidmap, GRU_MAX_GRUS);
+ struct gru_mm_tracker ms_asids[GRU_MAX_GRUS];
+};
+
+/*
+ * One of these structures is allocated when a GSEG is mmaped. The
+ * structure is pointed to by the vma->vm_private_data field in the vma struct.
+ */
+struct gru_vma_data {
+ spinlock_t vd_lock; /* Serialize access to vma */
+ struct list_head vd_head; /* head of linked list of gts */
+ long vd_user_options;/* misc user option flags */
+ int vd_cbr_au_count;
+ int vd_dsr_au_count;
+};
+
+/*
+ * One of these is allocated for each thread accessing a mmaped GRU. A linked
+ * list of these structure is hung off the struct gru_vma_data in the mm_struct.
+ */
+struct gru_thread_state {
+ struct list_head ts_next; /* list - head at vma-private */
+ struct mutex ts_ctxlock; /* load/unload CTX lock */
+ struct mm_struct *ts_mm; /* mm currently mapped to
+ context */
+ struct vm_area_struct *ts_vma; /* vma of GRU context */
+ struct gru_state *ts_gru; /* GRU where the context is
+ loaded */
+ struct gru_mm_struct *ts_gms; /* asid & ioproc struct */
+ unsigned long ts_cbr_map; /* map of allocated CBRs */
+ unsigned long ts_dsr_map; /* map of allocated DATA
+ resources */
+ unsigned long ts_steal_jiffies;/* jiffies when context last
+ stolen */
+ long ts_user_options;/* misc user option flags */
+ pid_t ts_tgid_owner; /* task that is using the
+ context - for migration */
+ int ts_tsid; /* thread that owns the
+ structure */
+ int ts_tlb_int_select;/* target cpu if interrupts
+ enabled */
+ int ts_ctxnum; /* context number where the
+ context is loaded */
+ atomic_t ts_refcnt; /* reference count GTS */
+ unsigned char ts_dsr_au_count;/* Number of DSR resources
+ required for contest */
+ unsigned char ts_cbr_au_count;/* Number of CBR resources
+ required for contest */
+ char ts_force_unload;/* force context to be unloaded
+ after migration */
+ char ts_cbr_idx[GRU_CBR_AU];/* CBR numbers of each
+ allocated CB */
+ unsigned long ts_gdata[0]; /* save area for GRU data (CB,
+ DS, CBE) */
+};
+
+/*
+ * Threaded programs actually allocate an array of GSEGs when a context is
+ * created. Each thread uses a separate GSEG. TSID is the index into the GSEG
+ * array.
+ */
+#define TSID(a, v) (((a) - (v)->vm_start) / GRU_GSEG_PAGESIZE)
+#define UGRUADDR(gts) ((gts)->ts_vma->vm_start + \
+ (gts)->ts_tsid * GRU_GSEG_PAGESIZE)
+
+#define NULLCTX (-1) /* if context not loaded into GRU */
+
+/*-----------------------------------------------------------------------------
+ * GRU State Tables
+ */
+
+/*
+ * One of these exists for each GRU chiplet.
+ */
+struct gru_state {
+ struct gru_blade_state *gs_blade; /* GRU state for entire
+ blade */
+ unsigned long gs_gru_base_paddr; /* Physical address of
+ gru segments (64) */
+ void *gs_gru_base_vaddr; /* Virtual address of
+ gru segments (64) */
+ unsigned char gs_gid; /* unique GRU number */
+ unsigned char gs_tgh_local_shift; /* used to pick TGH for
+ local flush */
+ unsigned char gs_tgh_first_remote; /* starting TGH# for
+ remote flush */
+ unsigned short gs_blade_id; /* blade of GRU */
+ spinlock_t gs_asid_lock; /* lock used for
+ assigning asids */
+ spinlock_t gs_lock; /* lock used for
+ assigning contexts */
+
+ /* -- the following are protected by the gs_asid_lock spinlock ---- */
+ unsigned int gs_asid; /* Next availe ASID */
+ unsigned int gs_asid_limit; /* Limit of available
+ ASIDs */
+ unsigned int gs_asid_gen; /* asid generation.
+ Inc on wrap */
+
+ /* --- the following fields are protected by the gs_lock spinlock --- */
+ unsigned long gs_context_map; /* bitmap to manage
+ contexts in use */
+ unsigned long gs_cbr_map; /* bitmap to manage CB
+ resources */
+ unsigned long gs_dsr_map; /* bitmap used to manage
+ DATA resources */
+ unsigned int gs_reserved_cbrs; /* Number of kernel-
+ reserved cbrs */
+ unsigned int gs_reserved_dsr_bytes; /* Bytes of kernel-
+ reserved dsrs */
+ unsigned short gs_active_contexts; /* number of contexts
+ in use */
+ struct gru_thread_state *gs_gts[GRU_NUM_CCH]; /* GTS currently using
+ the context */
+};
+
+/*
+ * This structure contains the GRU state for all the GRUs on a blade.
+ */
+struct gru_blade_state {
+ void *kernel_cb; /* First kernel
+ reserved cb */
+ void *kernel_dsr; /* First kernel
+ reserved DSR */
+ /* ---- the following are protected by the bs_lock spinlock ---- */
+ spinlock_t bs_lock; /* lock used for
+ stealing contexts */
+ int bs_lru_ctxnum; /* STEAL - last context
+ stolen */
+ struct gru_state *bs_lru_gru; /* STEAL - last gru
+ stolen */
+
+ struct gru_state bs_grus[GRU_CHIPLETS_PER_BLADE];
+};
+
+/*-----------------------------------------------------------------------------
+ * Address Primitives
+ */
+#define get_tfm_for_cpu(g, c) \
+ ((struct gru_tlb_fault_map *)get_tfm((g)->gs_gru_base_vaddr, (c)))
+#define get_tfh_by_index(g, i) \
+ ((struct gru_tlb_fault_handle *)get_tfh((g)->gs_gru_base_vaddr, (i)))
+#define get_tgh_by_index(g, i) \
+ ((struct gru_tlb_global_handle *)get_tgh((g)->gs_gru_base_vaddr, (i)))
+#define get_cbe_by_index(g, i) \
+ ((struct gru_control_block_extended *)get_cbe((g)->gs_gru_base_vaddr,\
+ (i)))
+
+/*-----------------------------------------------------------------------------
+ * Useful Macros
+ */
+
+/* Given a blade# & chiplet#, get a pointer to the GRU */
+#define get_gru(b, c) (&gru_base[b]->bs_grus[c])
+
+/* Number of bytes to save/restore when unloading/loading GRU contexts */
+#define DSR_BYTES(dsr) ((dsr) * GRU_DSR_AU_BYTES)
+#define CBR_BYTES(cbr) ((cbr) * GRU_HANDLE_BYTES * GRU_CBR_AU_SIZE * 2)
+
+/* Convert a user CB number to the actual CBRNUM */
+#define thread_cbr_number(gts, n) ((gts)->ts_cbr_idx[(n) / GRU_CBR_AU_SIZE] \
+ * GRU_CBR_AU_SIZE + (n) % GRU_CBR_AU_SIZE)
+
+/* Convert a gid to a pointer to the GRU */
+#define GID_TO_GRU(gid) \
+ (gru_base[(gid) / GRU_CHIPLETS_PER_BLADE] ? \
+ (&gru_base[(gid) / GRU_CHIPLETS_PER_BLADE]-> \
+ bs_grus[(gid) % GRU_CHIPLETS_PER_BLADE]) : \
+ NULL)
+
+/* Scan all active GRUs in a GRU bitmap */
+#define for_each_gru_in_bitmap(gid, map) \
+ for ((gid) = find_first_bit((map), GRU_MAX_GRUS); (gid) < GRU_MAX_GRUS;\
+ (gid)++, (gid) = find_next_bit((map), GRU_MAX_GRUS, (gid)))
+
+/* Scan all active GRUs on a specific blade */
+#define for_each_gru_on_blade(gru, nid, i) \
+ for ((gru) = gru_base[nid]->bs_grus, (i) = 0; \
+ (i) < GRU_CHIPLETS_PER_BLADE; \
+ (i)++, (gru)++)
+
+/* Scan all active GTSs on a gru. Note: must hold ss_lock to use this macro. */
+#define for_each_gts_on_gru(gts, gru, ctxnum) \
+ for ((ctxnum) = 0; (ctxnum) < GRU_NUM_CCH; (ctxnum)++) \
+ if (((gts) = (gru)->gs_gts[ctxnum]))
+
+/* Scan each CBR whose bit is set in a TFM (or copy of) */
+#define for_each_cbr_in_tfm(i, map) \
+ for ((i) = find_first_bit(map, GRU_NUM_CBE); \
+ (i) < GRU_NUM_CBE; \
+ (i)++, (i) = find_next_bit(map, GRU_NUM_CBE, i))
+
+/* Scan each CBR in a CBR bitmap. Note: multiple CBRs in an allocation unit */
+#define for_each_cbr_in_allocation_map(i, map, k) \
+ for ((k) = find_first_bit(map, GRU_CBR_AU); (k) < GRU_CBR_AU; \
+ (k) = find_next_bit(map, GRU_CBR_AU, (k) + 1)) \
+ for ((i) = (k)*GRU_CBR_AU_SIZE; \
+ (i) < ((k) + 1) * GRU_CBR_AU_SIZE; (i)++)
+
+/* Scan each DSR in a DSR bitmap. Note: multiple DSRs in an allocation unit */
+#define for_each_dsr_in_allocation_map(i, map, k) \
+ for ((k) = find_first_bit((const unsigned long *)map, GRU_DSR_AU);\
+ (k) < GRU_DSR_AU; \
+ (k) = find_next_bit((const unsigned long *)map, \
+ GRU_DSR_AU, (k) + 1)) \
+ for ((i) = (k) * GRU_DSR_AU_CL; \
+ (i) < ((k) + 1) * GRU_DSR_AU_CL; (i)++)
+
+#define gseg_physical_address(gru, ctxnum) \
+ ((gru)->gs_gru_base_paddr + ctxnum * GRU_GSEG_STRIDE)
+#define gseg_virtual_address(gru, ctxnum) \
+ ((gru)->gs_gru_base_vaddr + ctxnum * GRU_GSEG_STRIDE)
+
+/*-----------------------------------------------------------------------------
+ * Lock / Unlock GRU handles
+ * Use the "delresp" bit in the handle as a "lock" bit.
+ */
+
+/* Lock hierarchy checking enabled only in emulator */
+
+static inline void __lock_handle(void *h)
+{
+ while (test_and_set_bit(1, h))
+ cpu_relax();
+}
+
+static inline void __unlock_handle(void *h)
+{
+ clear_bit(1, h);
+}
+
+static inline void lock_cch_handle(struct gru_context_configuration_handle *cch)
+{
+ __lock_handle(cch);
+}
+
+static inline void unlock_cch_handle(struct gru_context_configuration_handle
+ *cch)
+{
+ __unlock_handle(cch);
+}
+
+static inline void lock_tgh_handle(struct gru_tlb_global_handle *tgh)
+{
+ __lock_handle(tgh);
+}
+
+static inline void unlock_tgh_handle(struct gru_tlb_global_handle *tgh)
+{
+ __unlock_handle(tgh);
+}
+
+/*-----------------------------------------------------------------------------
+ * Function prototypes & externs
+ */
+struct gru_unload_context_req;
+
+extern struct vm_operations_struct gru_vm_ops;
+extern struct device *grudev;
+
+extern struct gru_vma_data *gru_alloc_vma_data(struct vm_area_struct *vma,
+ int tsid);
+extern struct gru_thread_state *gru_find_thread_state(struct vm_area_struct
+ *vma, int tsid);
+extern struct gru_thread_state *gru_alloc_thread_state(struct vm_area_struct
+ *vma, int tsid);
+extern void gru_unload_context(struct gru_thread_state *gts, int savestate);
+extern void gts_drop(struct gru_thread_state *gts);
+extern void gru_tgh_flush_init(struct gru_state *gru);
+extern int gru_kservices_init(struct gru_state *gru);
+extern irqreturn_t gru_intr(int irq, void *dev_id);
+extern int gru_handle_user_call_os(unsigned long address);
+extern int gru_user_flush_tlb(unsigned long arg);
+extern int gru_user_unload_context(unsigned long arg);
+extern int gru_get_exception_detail(unsigned long arg);
+extern int gru_set_task_slice(long address);
+extern int gru_cpu_fault_map_id(void);
+extern struct vm_area_struct *gru_find_vma(unsigned long vaddr);
+extern void gru_flush_all_tlb(struct gru_state *gru);
+extern int gru_proc_init(void);
+extern void gru_proc_exit(void);
+
+extern unsigned long gru_reserve_cb_resources(struct gru_state *gru,
+ int cbr_au_count, char *cbmap);
+extern unsigned long gru_reserve_ds_resources(struct gru_state *gru,
+ int dsr_au_count, char *dsmap);
+extern int gru_fault(struct vm_area_struct *, struct vm_fault *vmf);
+extern struct gru_mm_struct *gru_register_mmu_notifier(void);
+extern void gru_drop_mmu_notifier(struct gru_mm_struct *gms);
+
+extern void gru_flush_tlb_range(struct gru_mm_struct *gms, unsigned long start,
+ unsigned long len);
+
+extern unsigned long gru_options;
+
+#endif /* __GRUTABLES_H__ */
--- /dev/null
+/*
+ * SN Platform GRU Driver
+ *
+ * MMUOPS callbacks + TLB flushing
+ *
+ * This file handles emu notifier callbacks from the core kernel. The callbacks
+ * are used to update the TLB in the GRU as a result of changes in the
+ * state of a process address space. This file also handles TLB invalidates
+ * from the GRU driver.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/hugetlb.h>
+#include <linux/delay.h>
+#include <linux/timex.h>
+#include <linux/srcu.h>
+#include <asm/processor.h>
+#include "gru.h"
+#include "grutables.h"
+#include <asm/uv/uv_hub.h>
+
+#define gru_random() get_cycles()
+
+/* ---------------------------------- TLB Invalidation functions --------
+ * get_tgh_handle
+ *
+ * Find a TGH to use for issuing a TLB invalidate. For GRUs that are on the
+ * local blade, use a fixed TGH that is a function of the blade-local cpu
+ * number. Normally, this TGH is private to the cpu & no contention occurs for
+ * the TGH. For offblade GRUs, select a random TGH in the range above the
+ * private TGHs. A spinlock is required to access this TGH & the lock must be
+ * released when the invalidate is completes. This sucks, but it is the best we
+ * can do.
+ *
+ * Note that the spinlock is IN the TGH handle so locking does not involve
+ * additional cache lines.
+ *
+ */
+static inline int get_off_blade_tgh(struct gru_state *gru)
+{
+ int n;
+
+ n = GRU_NUM_TGH - gru->gs_tgh_first_remote;
+ n = gru_random() % n;
+ n += gru->gs_tgh_first_remote;
+ return n;
+}
+
+static inline int get_on_blade_tgh(struct gru_state *gru)
+{
+ return uv_blade_processor_id() >> gru->gs_tgh_local_shift;
+}
+
+static struct gru_tlb_global_handle *get_lock_tgh_handle(struct gru_state
+ *gru)
+{
+ struct gru_tlb_global_handle *tgh;
+ int n;
+
+ preempt_disable();
+ if (uv_numa_blade_id() == gru->gs_blade_id)
+ n = get_on_blade_tgh(gru);
+ else
+ n = get_off_blade_tgh(gru);
+ tgh = get_tgh_by_index(gru, n);
+ lock_tgh_handle(tgh);
+
+ return tgh;
+}
+
+static void get_unlock_tgh_handle(struct gru_tlb_global_handle *tgh)
+{
+ unlock_tgh_handle(tgh);
+ preempt_enable();
+}
+
+/*
+ * gru_flush_tlb_range
+ *
+ * General purpose TLB invalidation function. This function scans every GRU in
+ * the ENTIRE system (partition) looking for GRUs where the specified MM has
+ * been accessed by the GRU. For each GRU found, the TLB must be invalidated OR
+ * the ASID invalidated. Invalidating an ASID causes a new ASID to be assigned
+ * on the next fault. This effectively flushes the ENTIRE TLB for the MM at the
+ * cost of (possibly) a large number of future TLBmisses.
+ *
+ * The current algorithm is optimized based on the following (somewhat true)
+ * assumptions:
+ * - GRU contexts are not loaded into a GRU unless a reference is made to
+ * the data segment or control block (this is true, not an assumption).
+ * If a DS/CB is referenced, the user will also issue instructions that
+ * cause TLBmisses. It is not necessary to optimize for the case where
+ * contexts are loaded but no instructions cause TLB misses. (I know
+ * this will happen but I'm not optimizing for it).
+ * - GRU instructions to invalidate TLB entries are SLOOOOWWW - normally
+ * a few usec but in unusual cases, it could be longer. Avoid if
+ * possible.
+ * - intrablade process migration between cpus is not frequent but is
+ * common.
+ * - a GRU context is not typically migrated to a different GRU on the
+ * blade because of intrablade migration
+ * - interblade migration is rare. Processes migrate their GRU context to
+ * the new blade.
+ * - if interblade migration occurs, migration back to the original blade
+ * is very very rare (ie., no optimization for this case)
+ * - most GRU instruction operate on a subset of the user REGIONS. Code
+ * & shared library regions are not likely targets of GRU instructions.
+ *
+ * To help improve the efficiency of TLB invalidation, the GMS data
+ * structure is maintained for EACH address space (MM struct). The GMS is
+ * also the structure that contains the pointer to the mmu callout
+ * functions. This structure is linked to the mm_struct for the address space
+ * using the mmu "register" function. The mmu interfaces are used to
+ * provide the callbacks for TLB invalidation. The GMS contains:
+ *
+ * - asid[maxgrus] array. ASIDs are assigned to a GRU when a context is
+ * loaded into the GRU.
+ * - asidmap[maxgrus]. bitmap to make it easier to find non-zero asids in
+ * the above array
+ * - ctxbitmap[maxgrus]. Indicates the contexts that are currently active
+ * in the GRU for the address space. This bitmap must be passed to the
+ * GRU to do an invalidate.
+ *
+ * The current algorithm for invalidating TLBs is:
+ * - scan the asidmap for GRUs where the context has been loaded, ie,
+ * asid is non-zero.
+ * - for each gru found:
+ * - if the ctxtmap is non-zero, there are active contexts in the
+ * GRU. TLB invalidate instructions must be issued to the GRU.
+ * - if the ctxtmap is zero, no context is active. Set the ASID to
+ * zero to force a full TLB invalidation. This is fast but will
+ * cause a lot of TLB misses if the context is reloaded onto the
+ * GRU
+ *
+ */
+
+void gru_flush_tlb_range(struct gru_mm_struct *gms, unsigned long start,
+ unsigned long len)
+{
+ struct gru_state *gru;
+ struct gru_mm_tracker *asids;
+ struct gru_tlb_global_handle *tgh;
+ unsigned long num;
+ int grupagesize, pagesize, pageshift, gid, asid;
+
+ /* ZZZ TODO - handle huge pages */
+ pageshift = PAGE_SHIFT;
+ pagesize = (1UL << pageshift);
+ grupagesize = GRU_PAGESIZE(pageshift);
+ num = min(((len + pagesize - 1) >> pageshift), GRUMAXINVAL);
+
+ STAT(flush_tlb);
+ gru_dbg(grudev, "gms %p, start 0x%lx, len 0x%lx, asidmap 0x%lx\n", gms,
+ start, len, gms->ms_asidmap[0]);
+
+ spin_lock(&gms->ms_asid_lock);
+ for_each_gru_in_bitmap(gid, gms->ms_asidmap) {
+ STAT(flush_tlb_gru);
+ gru = GID_TO_GRU(gid);
+ asids = gms->ms_asids + gid;
+ asid = asids->mt_asid;
+ if (asids->mt_ctxbitmap && asid) {
+ STAT(flush_tlb_gru_tgh);
+ asid = GRUASID(asid, start);
+ gru_dbg(grudev,
+ " FLUSH gruid %d, asid 0x%x, num %ld, cbmap 0x%x\n",
+ gid, asid, num, asids->mt_ctxbitmap);
+ tgh = get_lock_tgh_handle(gru);
+ tgh_invalidate(tgh, start, 0, asid, grupagesize, 0,
+ num - 1, asids->mt_ctxbitmap);
+ get_unlock_tgh_handle(tgh);
+ } else {
+ STAT(flush_tlb_gru_zero_asid);
+ asids->mt_asid = 0;
+ __clear_bit(gru->gs_gid, gms->ms_asidmap);
+ gru_dbg(grudev,
+ " CLEARASID gruid %d, asid 0x%x, cbtmap 0x%x, asidmap 0x%lx\n",
+ gid, asid, asids->mt_ctxbitmap,
+ gms->ms_asidmap[0]);
+ }
+ }
+ spin_unlock(&gms->ms_asid_lock);
+}
+
+/*
+ * Flush the entire TLB on a chiplet.
+ */
+void gru_flush_all_tlb(struct gru_state *gru)
+{
+ struct gru_tlb_global_handle *tgh;
+
+ gru_dbg(grudev, "gru %p, gid %d\n", gru, gru->gs_gid);
+ tgh = get_lock_tgh_handle(gru);
+ tgh_invalidate(tgh, 0, ~0, 0, 1, 1, GRUMAXINVAL - 1, 0);
+ get_unlock_tgh_handle(tgh);
+ preempt_enable();
+}
+
+/*
+ * MMUOPS notifier callout functions
+ */
+static void gru_invalidate_range_start(struct mmu_notifier *mn,
+ struct mm_struct *mm,
+ unsigned long start, unsigned long end)
+{
+ struct gru_mm_struct *gms = container_of(mn, struct gru_mm_struct,
+ ms_notifier);
+
+ STAT(mmu_invalidate_range);
+ atomic_inc(&gms->ms_range_active);
+ gru_dbg(grudev, "gms %p, start 0x%lx, end 0x%lx, act %d\n", gms,
+ start, end, atomic_read(&gms->ms_range_active));
+ gru_flush_tlb_range(gms, start, end - start);
+}
+
+static void gru_invalidate_range_end(struct mmu_notifier *mn,
+ struct mm_struct *mm, unsigned long start,
+ unsigned long end)
+{
+ struct gru_mm_struct *gms = container_of(mn, struct gru_mm_struct,
+ ms_notifier);
+
+ /* ..._and_test() provides needed barrier */
+ (void)atomic_dec_and_test(&gms->ms_range_active);
+
+ wake_up_all(&gms->ms_wait_queue);
+ gru_dbg(grudev, "gms %p, start 0x%lx, end 0x%lx\n", gms, start, end);
+}
+
+static void gru_invalidate_page(struct mmu_notifier *mn, struct mm_struct *mm,
+ unsigned long address)
+{
+ struct gru_mm_struct *gms = container_of(mn, struct gru_mm_struct,
+ ms_notifier);
+
+ STAT(mmu_invalidate_page);
+ gru_flush_tlb_range(gms, address, PAGE_SIZE);
+ gru_dbg(grudev, "gms %p, address 0x%lx\n", gms, address);
+}
+
+static void gru_release(struct mmu_notifier *mn, struct mm_struct *mm)
+{
+ struct gru_mm_struct *gms = container_of(mn, struct gru_mm_struct,
+ ms_notifier);
+
+ gms->ms_released = 1;
+ gru_dbg(grudev, "gms %p\n", gms);
+}
+
+
+static const struct mmu_notifier_ops gru_mmuops = {
+ .invalidate_page = gru_invalidate_page,
+ .invalidate_range_start = gru_invalidate_range_start,
+ .invalidate_range_end = gru_invalidate_range_end,
+ .release = gru_release,
+};
+
+/* Move this to the basic mmu_notifier file. But for now... */
+static struct mmu_notifier *mmu_find_ops(struct mm_struct *mm,
+ const struct mmu_notifier_ops *ops)
+{
+ struct mmu_notifier *mn, *gru_mn = NULL;
+ struct hlist_node *n;
+
+ if (mm->mmu_notifier_mm) {
+ rcu_read_lock();
+ hlist_for_each_entry_rcu(mn, n, &mm->mmu_notifier_mm->list,
+ hlist)
+ if (mn->ops == ops) {
+ gru_mn = mn;
+ break;
+ }
+ rcu_read_unlock();
+ }
+ return gru_mn;
+}
+
+struct gru_mm_struct *gru_register_mmu_notifier(void)
+{
+ struct gru_mm_struct *gms;
+ struct mmu_notifier *mn;
+
+ mn = mmu_find_ops(current->mm, &gru_mmuops);
+ if (mn) {
+ gms = container_of(mn, struct gru_mm_struct, ms_notifier);
+ atomic_inc(&gms->ms_refcnt);
+ } else {
+ gms = kzalloc(sizeof(*gms), GFP_KERNEL);
+ if (gms) {
+ spin_lock_init(&gms->ms_asid_lock);
+ gms->ms_notifier.ops = &gru_mmuops;
+ atomic_set(&gms->ms_refcnt, 1);
+ init_waitqueue_head(&gms->ms_wait_queue);
+ __mmu_notifier_register(&gms->ms_notifier, current->mm);
+ }
+ }
+ gru_dbg(grudev, "gms %p, refcnt %d\n", gms,
+ atomic_read(&gms->ms_refcnt));
+ return gms;
+}
+
+void gru_drop_mmu_notifier(struct gru_mm_struct *gms)
+{
+ gru_dbg(grudev, "gms %p, refcnt %d, released %d\n", gms,
+ atomic_read(&gms->ms_refcnt), gms->ms_released);
+ if (atomic_dec_return(&gms->ms_refcnt) == 0) {
+ if (!gms->ms_released)
+ mmu_notifier_unregister(&gms->ms_notifier, current->mm);
+ kfree(gms);
+ }
+}
+
+/*
+ * Setup TGH parameters. There are:
+ * - 24 TGH handles per GRU chiplet
+ * - a portion (MAX_LOCAL_TGH) of the handles are reserved for
+ * use by blade-local cpus
+ * - the rest are used by off-blade cpus. This usage is
+ * less frequent than blade-local usage.
+ *
+ * For now, use 16 handles for local flushes, 8 for remote flushes. If the blade
+ * has less tan or equal to 16 cpus, each cpu has a unique handle that it can
+ * use.
+ */
+#define MAX_LOCAL_TGH 16
+
+void gru_tgh_flush_init(struct gru_state *gru)
+{
+ int cpus, shift = 0, n;
+
+ cpus = uv_blade_nr_possible_cpus(gru->gs_blade_id);
+
+ /* n = cpus rounded up to next power of 2 */
+ if (cpus) {
+ n = 1 << fls(cpus - 1);
+
+ /*
+ * shift count for converting local cpu# to TGH index
+ * 0 if cpus <= MAX_LOCAL_TGH,
+ * 1 if cpus <= 2*MAX_LOCAL_TGH,
+ * etc
+ */
+ shift = max(0, fls(n - 1) - fls(MAX_LOCAL_TGH - 1));
+ }
+ gru->gs_tgh_local_shift = shift;
+
+ /* first starting TGH index to use for remote purges */
+ gru->gs_tgh_first_remote = (cpus + (1 << shift) - 1) >> shift;
+
+}
#
obj-$(CONFIG_SGI_XP) += xp.o
-xp-y := xp_main.o xp_nofault.o
+xp-y := xp_main.o
+xp-$(CONFIG_IA64_SGI_SN2) += xp_sn2.o xp_nofault.o
+xp-$(CONFIG_IA64_GENERIC) += xp_sn2.o xp_nofault.o xp_uv.o
+xp-$(CONFIG_IA64_SGI_UV) += xp_uv.o
+xp-$(CONFIG_X86_64) += xp_uv.o
obj-$(CONFIG_SGI_XP) += xpc.o
xpc-y := xpc_main.o xpc_channel.o xpc_partition.o
+xpc-$(CONFIG_IA64_SGI_SN2) += xpc_sn2.o
+xpc-$(CONFIG_IA64_GENERIC) += xpc_sn2.o xpc_uv.o
+xpc-$(CONFIG_IA64_SGI_UV) += xpc_uv.o
+xpc-$(CONFIG_X86_64) += xpc_uv.o
obj-$(CONFIG_SGI_XP) += xpnet.o
#ifndef _DRIVERS_MISC_SGIXP_XP_H
#define _DRIVERS_MISC_SGIXP_XP_H
-#include <linux/cache.h>
-#include <linux/hardirq.h>
#include <linux/mutex.h>
-#include <asm/sn/types.h>
-#include <asm/sn/bte.h>
+
+#ifdef CONFIG_IA64
+#include <asm/system.h>
+#include <asm/sn/arch.h> /* defines is_shub1() and is_shub2() */
+#define is_shub() ia64_platform_is("sn2")
+#define is_uv() ia64_platform_is("uv")
+#endif
+#ifdef CONFIG_X86_64
+#include <asm/genapic.h>
+#define is_uv() is_uv_system()
+#endif
+
+#ifndef is_shub1
+#define is_shub1() 0
+#endif
+
+#ifndef is_shub2
+#define is_shub2() 0
+#endif
+
+#ifndef is_shub
+#define is_shub() 0
+#endif
+
+#ifndef is_uv
+#define is_uv() 0
+#endif
#ifdef USE_DBUG_ON
#define DBUG_ON(condition) BUG_ON(condition)
#endif
/*
- * Define the maximum number of logically defined partitions the system
- * can support. It is constrained by the maximum number of hardware
- * partitionable regions. The term 'region' in this context refers to the
- * minimum number of nodes that can comprise an access protection grouping.
- * The access protection is in regards to memory, IPI and IOI.
+ * Define the maximum number of partitions the system can possibly support.
+ * It is based on the maximum number of hardware partitionable regions. The
+ * term 'region' in this context refers to the minimum number of nodes that
+ * can comprise an access protection grouping. The access protection is in
+ * regards to memory, IPI and IOI.
*
* The maximum number of hardware partitionable regions is equal to the
* maximum number of nodes in the entire system divided by the minimum number
* of nodes that comprise an access protection grouping.
*/
-#define XP_MAX_PARTITIONS 64
-
-/*
- * Define the number of u64s required to represent all the C-brick nasids
- * as a bitmap. The cross-partition kernel modules deal only with
- * C-brick nasids, thus the need for bitmaps which don't account for
- * odd-numbered (non C-brick) nasids.
- */
-#define XP_MAX_PHYSNODE_ID (MAX_NUMALINK_NODES / 2)
-#define XP_NASID_MASK_BYTES ((XP_MAX_PHYSNODE_ID + 7) / 8)
-#define XP_NASID_MASK_WORDS ((XP_MAX_PHYSNODE_ID + 63) / 64)
-
-/*
- * Wrapper for bte_copy() that should it return a failure status will retry
- * the bte_copy() once in the hope that the failure was due to a temporary
- * aberration (i.e., the link going down temporarily).
- *
- * src - physical address of the source of the transfer.
- * vdst - virtual address of the destination of the transfer.
- * len - number of bytes to transfer from source to destination.
- * mode - see bte_copy() for definition.
- * notification - see bte_copy() for definition.
- *
- * Note: xp_bte_copy() should never be called while holding a spinlock.
- */
-static inline bte_result_t
-xp_bte_copy(u64 src, u64 vdst, u64 len, u64 mode, void *notification)
-{
- bte_result_t ret;
- u64 pdst = ia64_tpa(vdst);
-
- /*
- * Ensure that the physically mapped memory is contiguous.
- *
- * We do this by ensuring that the memory is from region 7 only.
- * If the need should arise to use memory from one of the other
- * regions, then modify the BUG_ON() statement to ensure that the
- * memory from that region is always physically contiguous.
- */
- BUG_ON(REGION_NUMBER(vdst) != RGN_KERNEL);
-
- ret = bte_copy(src, pdst, len, mode, notification);
- if ((ret != BTE_SUCCESS) && BTE_ERROR_RETRY(ret)) {
- if (!in_interrupt())
- cond_resched();
-
- ret = bte_copy(src, pdst, len, mode, notification);
- }
-
- return ret;
-}
+#define XP_MAX_NPARTITIONS_SN2 64
+#define XP_MAX_NPARTITIONS_UV 256
/*
* XPC establishes channel connections between the local partition and any
* other partition that is currently up. Over these channels, kernel-level
* `users' can communicate with their counterparts on the other partitions.
*
- * The maxinum number of channels is limited to eight. For performance reasons,
- * the internal cross partition structures require sixteen bytes per channel,
- * and eight allows all of this interface-shared info to fit in one cache line.
- *
- * XPC_NCHANNELS reflects the total number of channels currently defined.
* If the need for additional channels arises, one can simply increase
- * XPC_NCHANNELS accordingly. If the day should come where that number
- * exceeds the MAXIMUM number of channels allowed (eight), then one will need
- * to make changes to the XPC code to allow for this.
+ * XPC_MAX_NCHANNELS accordingly. If the day should come where that number
+ * exceeds the absolute MAXIMUM number of channels possible (eight), then one
+ * will need to make changes to the XPC code to accommodate for this.
+ *
+ * The absolute maximum number of channels possible is limited to eight for
+ * performance reasons on sn2 hardware. The internal cross partition structures
+ * require sixteen bytes per channel, and eight allows all of this
+ * interface-shared info to fit in one 128-byte cacheline.
*/
#define XPC_MEM_CHANNEL 0 /* memory channel number */
#define XPC_NET_CHANNEL 1 /* network channel number */
-#define XPC_NCHANNELS 2 /* #of defined channels */
-#define XPC_MAX_NCHANNELS 8 /* max #of channels allowed */
+#define XPC_MAX_NCHANNELS 2 /* max #of channels allowed */
-#if XPC_NCHANNELS > XPC_MAX_NCHANNELS
-#error XPC_NCHANNELS exceeds MAXIMUM allowed.
+#if XPC_MAX_NCHANNELS > 8
+#error XPC_MAX_NCHANNELS exceeds absolute MAXIMUM possible.
#endif
/*
- * The format of an XPC message is as follows:
- *
- * +-------+--------------------------------+
- * | flags |////////////////////////////////|
- * +-------+--------------------------------+
- * | message # |
- * +----------------------------------------+
- * | payload (user-defined message) |
- * | |
- * :
- * | |
- * +----------------------------------------+
- *
- * The size of the payload is defined by the user via xpc_connect(). A user-
- * defined message resides in the payload area.
- *
- * The user should have no dealings with the message header, but only the
- * message's payload. When a message entry is allocated (via xpc_allocate())
- * a pointer to the payload area is returned and not the actual beginning of
- * the XPC message. The user then constructs a message in the payload area
- * and passes that pointer as an argument on xpc_send() or xpc_send_notify().
- *
- * The size of a message entry (within a message queue) must be a cacheline
- * sized multiple in order to facilitate the BTE transfer of messages from one
- * message queue to another. A macro, XPC_MSG_SIZE(), is provided for the user
+ * Define macro, XPC_MSG_SIZE(), is provided for the user
* that wants to fit as many msg entries as possible in a given memory size
* (e.g. a memory page).
*/
-struct xpc_msg {
- u8 flags; /* FOR XPC INTERNAL USE ONLY */
- u8 reserved[7]; /* FOR XPC INTERNAL USE ONLY */
- s64 number; /* FOR XPC INTERNAL USE ONLY */
-
- u64 payload; /* user defined portion of message */
-};
+#define XPC_MSG_MAX_SIZE 128
+#define XPC_MSG_HDR_MAX_SIZE 16
+#define XPC_MSG_PAYLOAD_MAX_SIZE (XPC_MSG_MAX_SIZE - XPC_MSG_HDR_MAX_SIZE)
-#define XPC_MSG_PAYLOAD_OFFSET (u64) (&((struct xpc_msg *)0)->payload)
#define XPC_MSG_SIZE(_payload_size) \
- L1_CACHE_ALIGN(XPC_MSG_PAYLOAD_OFFSET + (_payload_size))
+ ALIGN(XPC_MSG_HDR_MAX_SIZE + (_payload_size), \
+ is_uv() ? 64 : 128)
+
/*
* Define the return values and values passed to user's callout functions.
xpDisconnected, /* 51: channel disconnected (closed) */
xpBteCopyError, /* 52: bte_copy() returned error */
+ xpSalError, /* 53: sn SAL error */
+ xpRsvdPageNotSet, /* 54: the reserved page is not set up */
+ xpPayloadTooBig, /* 55: payload too large for message slot */
+
+ xpUnsupported, /* 56: unsupported functionality or resource */
+ xpNeedMoreInfo, /* 57: more info is needed by SAL */
- xpUnknownReason /* 53: unknown reason - must be last in enum */
+ xpGruCopyError, /* 58: gru_copy_gru() returned error */
+ xpGruSendMqError, /* 59: gru send message queue related error */
+
+ xpBadChannelNumber, /* 60: invalid channel number */
+ xpBadMsgType, /* 60: invalid message type */
+
+ xpUnknownReason /* 61: unknown reason - must be last in enum */
};
/*
* calling xpc_received().
*
* All other reason codes indicate failure.
+ *
+ * NOTE: The user defined function must be callable by an interrupt handler
+ * and thus cannot block.
*/
typedef void (*xpc_notify_func) (enum xp_retval reason, short partid,
int ch_number, void *key);
xpc_channel_func func; /* function to call */
void *key; /* pointer to user's key */
u16 nentries; /* #of msg entries in local msg queue */
- u16 msg_size; /* message queue's message size */
+ u16 entry_size; /* message queue's message entry size */
u32 assigned_limit; /* limit on #of assigned kthreads */
u32 idle_limit; /* limit on #of idle kthreads */
} ____cacheline_aligned;
#define XPC_CHANNEL_REGISTERED(_c) (xpc_registrations[_c].func != NULL)
-/* the following are valid xpc_allocate() flags */
+/* the following are valid xpc_send() or xpc_send_notify() flags */
#define XPC_WAIT 0 /* wait flag */
#define XPC_NOWAIT 1 /* no wait flag */
struct xpc_interface {
void (*connect) (int);
void (*disconnect) (int);
- enum xp_retval (*allocate) (short, int, u32, void **);
- enum xp_retval (*send) (short, int, void *);
- enum xp_retval (*send_notify) (short, int, void *,
+ enum xp_retval (*send) (short, int, u32, void *, u16);
+ enum xp_retval (*send_notify) (short, int, u32, void *, u16,
xpc_notify_func, void *);
void (*received) (short, int, void *);
enum xp_retval (*partid_to_nasids) (short, void *);
extern void xpc_set_interface(void (*)(int),
void (*)(int),
- enum xp_retval (*)(short, int, u32, void **),
- enum xp_retval (*)(short, int, void *),
- enum xp_retval (*)(short, int, void *,
- xpc_notify_func, void *),
+ enum xp_retval (*)(short, int, u32, void *, u16),
+ enum xp_retval (*)(short, int, u32, void *, u16,
+ xpc_notify_func, void *),
void (*)(short, int, void *),
enum xp_retval (*)(short, void *));
extern void xpc_clear_interface(void);
extern void xpc_disconnect(int);
static inline enum xp_retval
-xpc_allocate(short partid, int ch_number, u32 flags, void **payload)
-{
- return xpc_interface.allocate(partid, ch_number, flags, payload);
-}
-
-static inline enum xp_retval
-xpc_send(short partid, int ch_number, void *payload)
+xpc_send(short partid, int ch_number, u32 flags, void *payload,
+ u16 payload_size)
{
- return xpc_interface.send(partid, ch_number, payload);
+ return xpc_interface.send(partid, ch_number, flags, payload,
+ payload_size);
}
static inline enum xp_retval
-xpc_send_notify(short partid, int ch_number, void *payload,
- xpc_notify_func func, void *key)
+xpc_send_notify(short partid, int ch_number, u32 flags, void *payload,
+ u16 payload_size, xpc_notify_func func, void *key)
{
- return xpc_interface.send_notify(partid, ch_number, payload, func, key);
+ return xpc_interface.send_notify(partid, ch_number, flags, payload,
+ payload_size, func, key);
}
static inline void
return xpc_interface.partid_to_nasids(partid, nasids);
}
+extern short xp_max_npartitions;
+extern short xp_partition_id;
+extern u8 xp_region_size;
+
+extern unsigned long (*xp_pa) (void *);
+extern enum xp_retval (*xp_remote_memcpy) (unsigned long, const unsigned long,
+ size_t);
+extern int (*xp_cpu_to_nasid) (int);
+
extern u64 xp_nofault_PIOR_target;
extern int xp_nofault_PIOR(void *);
extern int xp_error_PIOR(void);
+extern struct device *xp;
+extern enum xp_retval xp_init_sn2(void);
+extern enum xp_retval xp_init_uv(void);
+extern void xp_exit_sn2(void);
+extern void xp_exit_uv(void);
+
#endif /* _DRIVERS_MISC_SGIXP_XP_H */
*
*/
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
#include <linux/module.h>
-#include <linux/mutex.h>
-#include <asm/sn/intr.h>
-#include <asm/sn/sn_sal.h>
+#include <linux/device.h>
#include "xp.h"
-/*
- * The export of xp_nofault_PIOR needs to happen here since it is defined
- * in drivers/misc/sgi-xp/xp_nofault.S. The target of the nofault read is
- * defined here.
- */
-EXPORT_SYMBOL_GPL(xp_nofault_PIOR);
+/* define the XP debug device structures to be used with dev_dbg() et al */
+
+struct device_driver xp_dbg_name = {
+ .name = "xp"
+};
+
+struct device xp_dbg_subname = {
+ .bus_id = {0}, /* set to "" */
+ .driver = &xp_dbg_name
+};
+
+struct device *xp = &xp_dbg_subname;
+
+/* max #of partitions possible */
+short xp_max_npartitions;
+EXPORT_SYMBOL_GPL(xp_max_npartitions);
+
+short xp_partition_id;
+EXPORT_SYMBOL_GPL(xp_partition_id);
+
+u8 xp_region_size;
+EXPORT_SYMBOL_GPL(xp_region_size);
+
+unsigned long (*xp_pa) (void *addr);
+EXPORT_SYMBOL_GPL(xp_pa);
+
+enum xp_retval (*xp_remote_memcpy) (unsigned long dst_gpa,
+ const unsigned long src_gpa, size_t len);
+EXPORT_SYMBOL_GPL(xp_remote_memcpy);
-u64 xp_nofault_PIOR_target;
-EXPORT_SYMBOL_GPL(xp_nofault_PIOR_target);
+int (*xp_cpu_to_nasid) (int cpuid);
+EXPORT_SYMBOL_GPL(xp_cpu_to_nasid);
/*
* xpc_registrations[] keeps track of xpc_connect()'s done by the kernel-level
* users of XPC.
*/
-struct xpc_registration xpc_registrations[XPC_NCHANNELS];
+struct xpc_registration xpc_registrations[XPC_MAX_NCHANNELS];
EXPORT_SYMBOL_GPL(xpc_registrations);
/*
struct xpc_interface xpc_interface = {
(void (*)(int))xpc_notloaded,
(void (*)(int))xpc_notloaded,
- (enum xp_retval(*)(short, int, u32, void **))xpc_notloaded,
- (enum xp_retval(*)(short, int, void *))xpc_notloaded,
- (enum xp_retval(*)(short, int, void *, xpc_notify_func, void *))
- xpc_notloaded,
+ (enum xp_retval(*)(short, int, u32, void *, u16))xpc_notloaded,
+ (enum xp_retval(*)(short, int, u32, void *, u16, xpc_notify_func,
+ void *))xpc_notloaded,
(void (*)(short, int, void *))xpc_notloaded,
(enum xp_retval(*)(short, void *))xpc_notloaded
};
void
xpc_set_interface(void (*connect) (int),
void (*disconnect) (int),
- enum xp_retval (*allocate) (short, int, u32, void **),
- enum xp_retval (*send) (short, int, void *),
- enum xp_retval (*send_notify) (short, int, void *,
+ enum xp_retval (*send) (short, int, u32, void *, u16),
+ enum xp_retval (*send_notify) (short, int, u32, void *, u16,
xpc_notify_func, void *),
void (*received) (short, int, void *),
enum xp_retval (*partid_to_nasids) (short, void *))
{
xpc_interface.connect = connect;
xpc_interface.disconnect = disconnect;
- xpc_interface.allocate = allocate;
xpc_interface.send = send;
xpc_interface.send_notify = send_notify;
xpc_interface.received = received;
{
xpc_interface.connect = (void (*)(int))xpc_notloaded;
xpc_interface.disconnect = (void (*)(int))xpc_notloaded;
- xpc_interface.allocate = (enum xp_retval(*)(short, int, u32,
- void **))xpc_notloaded;
- xpc_interface.send = (enum xp_retval(*)(short, int, void *))
+ xpc_interface.send = (enum xp_retval(*)(short, int, u32, void *, u16))
xpc_notloaded;
- xpc_interface.send_notify = (enum xp_retval(*)(short, int, void *,
- xpc_notify_func,
- void *))xpc_notloaded;
+ xpc_interface.send_notify = (enum xp_retval(*)(short, int, u32, void *,
+ u16, xpc_notify_func,
+ void *))xpc_notloaded;
xpc_interface.received = (void (*)(short, int, void *))
xpc_notloaded;
xpc_interface.partid_to_nasids = (enum xp_retval(*)(short, void *))
{
struct xpc_registration *registration;
- DBUG_ON(ch_number < 0 || ch_number >= XPC_NCHANNELS);
+ DBUG_ON(ch_number < 0 || ch_number >= XPC_MAX_NCHANNELS);
DBUG_ON(payload_size == 0 || nentries == 0);
DBUG_ON(func == NULL);
DBUG_ON(assigned_limit == 0 || idle_limit > assigned_limit);
+ if (XPC_MSG_SIZE(payload_size) > XPC_MSG_MAX_SIZE)
+ return xpPayloadTooBig;
+
registration = &xpc_registrations[ch_number];
if (mutex_lock_interruptible(®istration->mutex) != 0)
}
/* register the channel for connection */
- registration->msg_size = XPC_MSG_SIZE(payload_size);
+ registration->entry_size = XPC_MSG_SIZE(payload_size);
registration->nentries = nentries;
registration->assigned_limit = assigned_limit;
registration->idle_limit = idle_limit;
{
struct xpc_registration *registration;
- DBUG_ON(ch_number < 0 || ch_number >= XPC_NCHANNELS);
+ DBUG_ON(ch_number < 0 || ch_number >= XPC_MAX_NCHANNELS);
registration = &xpc_registrations[ch_number];
registration->func = NULL;
registration->key = NULL;
registration->nentries = 0;
- registration->msg_size = 0;
+ registration->entry_size = 0;
registration->assigned_limit = 0;
registration->idle_limit = 0;
int __init
xp_init(void)
{
- int ret, ch_number;
- u64 func_addr = *(u64 *)xp_nofault_PIOR;
- u64 err_func_addr = *(u64 *)xp_error_PIOR;
-
- if (!ia64_platform_is("sn2"))
- return -ENODEV;
+ enum xp_retval ret;
+ int ch_number;
- /*
- * Register a nofault code region which performs a cross-partition
- * PIO read. If the PIO read times out, the MCA handler will consume
- * the error and return to a kernel-provided instruction to indicate
- * an error. This PIO read exists because it is guaranteed to timeout
- * if the destination is down (AMO operations do not timeout on at
- * least some CPUs on Shubs <= v1.2, which unfortunately we have to
- * work around).
- */
- ret = sn_register_nofault_code(func_addr, err_func_addr, err_func_addr,
- 1, 1);
- if (ret != 0) {
- printk(KERN_ERR "XP: can't register nofault code, error=%d\n",
- ret);
- }
- /*
- * Setup the nofault PIO read target. (There is no special reason why
- * SH_IPI_ACCESS was selected.)
- */
- if (is_shub2())
- xp_nofault_PIOR_target = SH2_IPI_ACCESS0;
+ if (is_shub())
+ ret = xp_init_sn2();
+ else if (is_uv())
+ ret = xp_init_uv();
else
- xp_nofault_PIOR_target = SH1_IPI_ACCESS;
+ ret = xpUnsupported;
+
+ if (ret != xpSuccess)
+ return -ENODEV;
/* initialize the connection registration mutex */
- for (ch_number = 0; ch_number < XPC_NCHANNELS; ch_number++)
+ for (ch_number = 0; ch_number < XPC_MAX_NCHANNELS; ch_number++)
mutex_init(&xpc_registrations[ch_number].mutex);
return 0;
void __exit
xp_exit(void)
{
- u64 func_addr = *(u64 *)xp_nofault_PIOR;
- u64 err_func_addr = *(u64 *)xp_error_PIOR;
-
- /* unregister the PIO read nofault code region */
- (void)sn_register_nofault_code(func_addr, err_func_addr,
- err_func_addr, 1, 0);
+ if (is_shub())
+ xp_exit_sn2();
+ else if (is_uv())
+ xp_exit_uv();
}
module_exit(xp_exit);
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ */
+
+/*
+ * Cross Partition (XP) sn2-based functions.
+ *
+ * Architecture specific implementation of common functions.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <asm/sn/bte.h>
+#include <asm/sn/sn_sal.h>
+#include "xp.h"
+
+/*
+ * The export of xp_nofault_PIOR needs to happen here since it is defined
+ * in drivers/misc/sgi-xp/xp_nofault.S. The target of the nofault read is
+ * defined here.
+ */
+EXPORT_SYMBOL_GPL(xp_nofault_PIOR);
+
+u64 xp_nofault_PIOR_target;
+EXPORT_SYMBOL_GPL(xp_nofault_PIOR_target);
+
+/*
+ * Register a nofault code region which performs a cross-partition PIO read.
+ * If the PIO read times out, the MCA handler will consume the error and
+ * return to a kernel-provided instruction to indicate an error. This PIO read
+ * exists because it is guaranteed to timeout if the destination is down
+ * (amo operations do not timeout on at least some CPUs on Shubs <= v1.2,
+ * which unfortunately we have to work around).
+ */
+static enum xp_retval
+xp_register_nofault_code_sn2(void)
+{
+ int ret;
+ u64 func_addr;
+ u64 err_func_addr;
+
+ func_addr = *(u64 *)xp_nofault_PIOR;
+ err_func_addr = *(u64 *)xp_error_PIOR;
+ ret = sn_register_nofault_code(func_addr, err_func_addr, err_func_addr,
+ 1, 1);
+ if (ret != 0) {
+ dev_err(xp, "can't register nofault code, error=%d\n", ret);
+ return xpSalError;
+ }
+ /*
+ * Setup the nofault PIO read target. (There is no special reason why
+ * SH_IPI_ACCESS was selected.)
+ */
+ if (is_shub1())
+ xp_nofault_PIOR_target = SH1_IPI_ACCESS;
+ else if (is_shub2())
+ xp_nofault_PIOR_target = SH2_IPI_ACCESS0;
+
+ return xpSuccess;
+}
+
+static void
+xp_unregister_nofault_code_sn2(void)
+{
+ u64 func_addr = *(u64 *)xp_nofault_PIOR;
+ u64 err_func_addr = *(u64 *)xp_error_PIOR;
+
+ /* unregister the PIO read nofault code region */
+ (void)sn_register_nofault_code(func_addr, err_func_addr,
+ err_func_addr, 1, 0);
+}
+
+/*
+ * Convert a virtual memory address to a physical memory address.
+ */
+static unsigned long
+xp_pa_sn2(void *addr)
+{
+ return __pa(addr);
+}
+
+/*
+ * Wrapper for bte_copy().
+ *
+ * dst_pa - physical address of the destination of the transfer.
+ * src_pa - physical address of the source of the transfer.
+ * len - number of bytes to transfer from source to destination.
+ *
+ * Note: xp_remote_memcpy_sn2() should never be called while holding a spinlock.
+ */
+static enum xp_retval
+xp_remote_memcpy_sn2(unsigned long dst_pa, const unsigned long src_pa,
+ size_t len)
+{
+ bte_result_t ret;
+
+ ret = bte_copy(src_pa, dst_pa, len, (BTE_NOTIFY | BTE_WACQUIRE), NULL);
+ if (ret == BTE_SUCCESS)
+ return xpSuccess;
+
+ if (is_shub2()) {
+ dev_err(xp, "bte_copy() on shub2 failed, error=0x%x dst_pa="
+ "0x%016lx src_pa=0x%016lx len=%ld\\n", ret, dst_pa,
+ src_pa, len);
+ } else {
+ dev_err(xp, "bte_copy() failed, error=%d dst_pa=0x%016lx "
+ "src_pa=0x%016lx len=%ld\\n", ret, dst_pa, src_pa, len);
+ }
+
+ return xpBteCopyError;
+}
+
+static int
+xp_cpu_to_nasid_sn2(int cpuid)
+{
+ return cpuid_to_nasid(cpuid);
+}
+
+enum xp_retval
+xp_init_sn2(void)
+{
+ BUG_ON(!is_shub());
+
+ xp_max_npartitions = XP_MAX_NPARTITIONS_SN2;
+ xp_partition_id = sn_partition_id;
+ xp_region_size = sn_region_size;
+
+ xp_pa = xp_pa_sn2;
+ xp_remote_memcpy = xp_remote_memcpy_sn2;
+ xp_cpu_to_nasid = xp_cpu_to_nasid_sn2;
+
+ return xp_register_nofault_code_sn2();
+}
+
+void
+xp_exit_sn2(void)
+{
+ BUG_ON(!is_shub());
+
+ xp_unregister_nofault_code_sn2();
+}
+
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ */
+
+/*
+ * Cross Partition (XP) uv-based functions.
+ *
+ * Architecture specific implementation of common functions.
+ *
+ */
+
+#include <linux/device.h>
+#include <asm/uv/uv_hub.h>
+#include "../sgi-gru/grukservices.h"
+#include "xp.h"
+
+/*
+ * Convert a virtual memory address to a physical memory address.
+ */
+static unsigned long
+xp_pa_uv(void *addr)
+{
+ return uv_gpa(addr);
+}
+
+static enum xp_retval
+xp_remote_memcpy_uv(unsigned long dst_gpa, const unsigned long src_gpa,
+ size_t len)
+{
+ int ret;
+
+ ret = gru_copy_gpa(dst_gpa, src_gpa, len);
+ if (ret == 0)
+ return xpSuccess;
+
+ dev_err(xp, "gru_copy_gpa() failed, dst_gpa=0x%016lx src_gpa=0x%016lx "
+ "len=%ld\n", dst_gpa, src_gpa, len);
+ return xpGruCopyError;
+}
+
+static int
+xp_cpu_to_nasid_uv(int cpuid)
+{
+ /* ??? Is this same as sn2 nasid in mach/part bitmaps set up by SAL? */
+ return UV_PNODE_TO_NASID(uv_cpu_to_pnode(cpuid));
+}
+
+enum xp_retval
+xp_init_uv(void)
+{
+ BUG_ON(!is_uv());
+
+ xp_max_npartitions = XP_MAX_NPARTITIONS_UV;
+ xp_partition_id = 0; /* !!! not correct value */
+ xp_region_size = 0; /* !!! not correct value */
+
+ xp_pa = xp_pa_uv;
+ xp_remote_memcpy = xp_remote_memcpy_uv;
+ xp_cpu_to_nasid = xp_cpu_to_nasid_uv;
+
+ return xpSuccess;
+}
+
+void
+xp_exit_uv(void)
+{
+ BUG_ON(!is_uv());
+}
#ifndef _DRIVERS_MISC_SGIXP_XPC_H
#define _DRIVERS_MISC_SGIXP_XPC_H
-#include <linux/interrupt.h>
-#include <linux/sysctl.h>
-#include <linux/device.h>
-#include <linux/mutex.h>
+#include <linux/wait.h>
#include <linux/completion.h>
-#include <asm/pgtable.h>
-#include <asm/processor.h>
-#include <asm/sn/bte.h>
-#include <asm/sn/clksupport.h>
-#include <asm/sn/addrs.h>
-#include <asm/sn/mspec.h>
-#include <asm/sn/shub_mmr.h>
+#include <linux/timer.h>
+#include <linux/sched.h>
#include "xp.h"
/*
#define XPC_VERSION_MAJOR(_v) ((_v) >> 4)
#define XPC_VERSION_MINOR(_v) ((_v) & 0xf)
-/*
- * The next macros define word or bit representations for given
- * C-brick nasid in either the SAL provided bit array representing
- * nasids in the partition/machine or the AMO_t array used for
- * inter-partition initiation communications.
- *
- * For SN2 machines, C-Bricks are alway even numbered NASIDs. As
- * such, some space will be saved by insisting that nasid information
- * passed from SAL always be packed for C-Bricks and the
- * cross-partition interrupts use the same packing scheme.
- */
-#define XPC_NASID_W_INDEX(_n) (((_n) / 64) / 2)
-#define XPC_NASID_B_INDEX(_n) (((_n) / 2) & (64 - 1))
-#define XPC_NASID_IN_ARRAY(_n, _p) ((_p)[XPC_NASID_W_INDEX(_n)] & \
- (1UL << XPC_NASID_B_INDEX(_n)))
-#define XPC_NASID_FROM_W_B(_w, _b) (((_w) * 64 + (_b)) * 2)
-
+/* define frequency of the heartbeat and frequency how often it's checked */
#define XPC_HB_DEFAULT_INTERVAL 5 /* incr HB every x secs */
#define XPC_HB_CHECK_DEFAULT_INTERVAL 20 /* check HB every x secs */
*
* reserved page header
*
- * The first cacheline of the reserved page contains the header
- * (struct xpc_rsvd_page). Before SAL initialization has completed,
+ * The first two 64-byte cachelines of the reserved page contain the
+ * header (struct xpc_rsvd_page). Before SAL initialization has completed,
* SAL has set up the following fields of the reserved page header:
- * SAL_signature, SAL_version, partid, and nasids_size. The other
- * fields are set up by XPC. (xpc_rsvd_page points to the local
+ * SAL_signature, SAL_version, SAL_partid, and SAL_nasids_size. The
+ * other fields are set up by XPC. (xpc_rsvd_page points to the local
* partition's reserved page.)
*
* part_nasids mask
* the actual nasids in the entire machine (mach_nasids). We're only
* interested in the even numbered nasids (which contain the processors
* and/or memory), so we only need half as many bits to represent the
- * nasids. The part_nasids mask is located starting at the first cacheline
- * following the reserved page header. The mach_nasids mask follows right
- * after the part_nasids mask. The size in bytes of each mask is reflected
- * by the reserved page header field 'nasids_size'. (Local partition's
- * mask pointers are xpc_part_nasids and xpc_mach_nasids.)
+ * nasids. When mapping nasid to bit in a mask (or bit to nasid) be sure
+ * to either divide or multiply by 2. The part_nasids mask is located
+ * starting at the first cacheline following the reserved page header. The
+ * mach_nasids mask follows right after the part_nasids mask. The size in
+ * bytes of each mask is reflected by the reserved page header field
+ * 'SAL_nasids_size'. (Local partition's mask pointers are xpc_part_nasids
+ * and xpc_mach_nasids.)
*
- * vars
- * vars part
+ * vars (ia64-sn2 only)
+ * vars part (ia64-sn2 only)
*
* Immediately following the mach_nasids mask are the XPC variables
* required by other partitions. First are those that are generic to all
* which are partition specific (vars part). These are setup by XPC.
* (Local partition's vars pointers are xpc_vars and xpc_vars_part.)
*
- * Note: Until vars_pa is set, the partition XPC code has not been initialized.
+ * Note: Until 'ts_jiffies' is set non-zero, the partition XPC code has not been
+ * initialized.
*/
struct xpc_rsvd_page {
u64 SAL_signature; /* SAL: unique signature */
u64 SAL_version; /* SAL: version */
- u8 partid; /* SAL: partition ID */
+ short SAL_partid; /* SAL: partition ID */
+ short max_npartitions; /* value of XPC_MAX_PARTITIONS */
u8 version;
- u8 pad1[6]; /* align to next u64 in cacheline */
- u64 vars_pa; /* physical address of struct xpc_vars */
- struct timespec stamp; /* time when reserved page was setup by XPC */
- u64 pad2[9]; /* align to last u64 in cacheline */
- u64 nasids_size; /* SAL: size of each nasid mask in bytes */
+ u8 pad1[3]; /* align to next u64 in 1st 64-byte cacheline */
+ union {
+ unsigned long vars_pa; /* phys address of struct xpc_vars */
+ unsigned long activate_mq_gpa; /* gru phy addr of activate_mq */
+ } sn;
+ unsigned long ts_jiffies; /* timestamp when rsvd pg was setup by XPC */
+ u64 pad2[10]; /* align to last u64 in 2nd 64-byte cacheline */
+ u64 SAL_nasids_size; /* SAL: size of each nasid mask in bytes */
};
-#define XPC_RP_VERSION _XPC_VERSION(1, 1) /* version 1.1 of the reserved page */
-
-#define XPC_SUPPORTS_RP_STAMP(_version) \
- (_version >= _XPC_VERSION(1, 1))
-
-/*
- * compare stamps - the return value is:
- *
- * < 0, if stamp1 < stamp2
- * = 0, if stamp1 == stamp2
- * > 0, if stamp1 > stamp2
- */
-static inline int
-xpc_compare_stamps(struct timespec *stamp1, struct timespec *stamp2)
-{
- int ret;
-
- ret = stamp1->tv_sec - stamp2->tv_sec;
- if (ret == 0)
- ret = stamp1->tv_nsec - stamp2->tv_nsec;
-
- return ret;
-}
+#define XPC_RP_VERSION _XPC_VERSION(2, 0) /* version 2.0 of the reserved page */
/*
* Define the structures by which XPC variables can be exported to other
* reflected by incrementing either the major or minor version numbers
* of struct xpc_vars.
*/
-struct xpc_vars {
+struct xpc_vars_sn2 {
u8 version;
u64 heartbeat;
- u64 heartbeating_to_mask;
+ DECLARE_BITMAP(heartbeating_to_mask, XP_MAX_NPARTITIONS_SN2);
u64 heartbeat_offline; /* if 0, heartbeat should be changing */
- int act_nasid;
- int act_phys_cpuid;
- u64 vars_part_pa;
- u64 amos_page_pa; /* paddr of page of AMOs from MSPEC driver */
- AMO_t *amos_page; /* vaddr of page of AMOs from MSPEC driver */
+ int activate_IRQ_nasid;
+ int activate_IRQ_phys_cpuid;
+ unsigned long vars_part_pa;
+ unsigned long amos_page_pa;/* paddr of page of amos from MSPEC driver */
+ struct amo *amos_page; /* vaddr of page of amos from MSPEC driver */
};
#define XPC_V_VERSION _XPC_VERSION(3, 1) /* version 3.1 of the cross vars */
-#define XPC_SUPPORTS_DISENGAGE_REQUEST(_version) \
- (_version >= _XPC_VERSION(3, 1))
-
-static inline int
-xpc_hb_allowed(short partid, struct xpc_vars *vars)
-{
- return ((vars->heartbeating_to_mask & (1UL << partid)) != 0);
-}
-
-static inline void
-xpc_allow_hb(short partid, struct xpc_vars *vars)
-{
- u64 old_mask, new_mask;
-
- do {
- old_mask = vars->heartbeating_to_mask;
- new_mask = (old_mask | (1UL << partid));
- } while (cmpxchg(&vars->heartbeating_to_mask, old_mask, new_mask) !=
- old_mask);
-}
-
-static inline void
-xpc_disallow_hb(short partid, struct xpc_vars *vars)
-{
- u64 old_mask, new_mask;
-
- do {
- old_mask = vars->heartbeating_to_mask;
- new_mask = (old_mask & ~(1UL << partid));
- } while (cmpxchg(&vars->heartbeating_to_mask, old_mask, new_mask) !=
- old_mask);
-}
-
-/*
- * The AMOs page consists of a number of AMO variables which are divided into
- * four groups, The first two groups are used to identify an IRQ's sender.
- * These two groups consist of 64 and 128 AMO variables respectively. The last
- * two groups, consisting of just one AMO variable each, are used to identify
- * the remote partitions that are currently engaged (from the viewpoint of
- * the XPC running on the remote partition).
- */
-#define XPC_NOTIFY_IRQ_AMOS 0
-#define XPC_ACTIVATE_IRQ_AMOS (XPC_NOTIFY_IRQ_AMOS + XP_MAX_PARTITIONS)
-#define XPC_ENGAGED_PARTITIONS_AMO (XPC_ACTIVATE_IRQ_AMOS + XP_NASID_MASK_WORDS)
-#define XPC_DISENGAGE_REQUEST_AMO (XPC_ENGAGED_PARTITIONS_AMO + 1)
-
/*
* The following structure describes the per partition specific variables.
*
* An array of these structures, one per partition, will be defined. As a
* partition becomes active XPC will copy the array entry corresponding to
- * itself from that partition. It is desirable that the size of this
- * structure evenly divide into a cacheline, such that none of the entries
- * in this array crosses a cacheline boundary. As it is now, each entry
- * occupies half a cacheline.
+ * itself from that partition. It is desirable that the size of this structure
+ * evenly divides into a 128-byte cacheline, such that none of the entries in
+ * this array crosses a 128-byte cacheline boundary. As it is now, each entry
+ * occupies 64-bytes.
*/
-struct xpc_vars_part {
+struct xpc_vars_part_sn2 {
u64 magic;
- u64 openclose_args_pa; /* physical address of open and close args */
- u64 GPs_pa; /* physical address of Get/Put values */
+ unsigned long openclose_args_pa; /* phys addr of open and close args */
+ unsigned long GPs_pa; /* physical address of Get/Put values */
+
+ unsigned long chctl_amo_pa; /* physical address of chctl flags' amo */
- u64 IPI_amo_pa; /* physical address of IPI AMO_t structure */
- int IPI_nasid; /* nasid of where to send IPIs */
- int IPI_phys_cpuid; /* physical CPU ID of where to send IPIs */
+ int notify_IRQ_nasid; /* nasid of where to send notify IRQs */
+ int notify_IRQ_phys_cpuid; /* CPUID of where to send notify IRQs */
u8 nchannels; /* #of defined channels supported */
* MAGIC2 indicates that this partition has pulled the remote partititions
* per partition variables that pertain to this partition.
*/
-#define XPC_VP_MAGIC1 0x0053524156435058L /* 'XPCVARS\0'L (little endian) */
-#define XPC_VP_MAGIC2 0x0073726176435058L /* 'XPCvars\0'L (little endian) */
+#define XPC_VP_MAGIC1_SN2 0x0053524156435058L /* 'XPCVARS\0'L (little endian) */
+#define XPC_VP_MAGIC2_SN2 0x0073726176435058L /* 'XPCvars\0'L (little endian) */
/* the reserved page sizes and offsets */
#define XPC_RP_HEADER_SIZE L1_CACHE_ALIGN(sizeof(struct xpc_rsvd_page))
-#define XPC_RP_VARS_SIZE L1_CACHE_ALIGN(sizeof(struct xpc_vars))
+#define XPC_RP_VARS_SIZE L1_CACHE_ALIGN(sizeof(struct xpc_vars_sn2))
-#define XPC_RP_PART_NASIDS(_rp) ((u64 *)((u8 *)(_rp) + XPC_RP_HEADER_SIZE))
-#define XPC_RP_MACH_NASIDS(_rp) (XPC_RP_PART_NASIDS(_rp) + xp_nasid_mask_words)
-#define XPC_RP_VARS(_rp) ((struct xpc_vars *)(XPC_RP_MACH_NASIDS(_rp) + \
- xp_nasid_mask_words))
-#define XPC_RP_VARS_PART(_rp) ((struct xpc_vars_part *) \
- ((u8 *)XPC_RP_VARS(_rp) + XPC_RP_VARS_SIZE))
+#define XPC_RP_PART_NASIDS(_rp) ((unsigned long *)((u8 *)(_rp) + \
+ XPC_RP_HEADER_SIZE))
+#define XPC_RP_MACH_NASIDS(_rp) (XPC_RP_PART_NASIDS(_rp) + \
+ xpc_nasid_mask_nlongs)
+#define XPC_RP_VARS(_rp) ((struct xpc_vars_sn2 *) \
+ (XPC_RP_MACH_NASIDS(_rp) + \
+ xpc_nasid_mask_nlongs))
+
+/*
+ * The activate_mq is used to send/receive GRU messages that affect XPC's
+ * heartbeat, partition active state, and channel state. This is UV only.
+ */
+struct xpc_activate_mq_msghdr_uv {
+ short partid; /* sender's partid */
+ u8 act_state; /* sender's act_state at time msg sent */
+ u8 type; /* message's type */
+ unsigned long rp_ts_jiffies; /* timestamp of sender's rp setup by XPC */
+};
+
+/* activate_mq defined message types */
+#define XPC_ACTIVATE_MQ_MSG_SYNC_ACT_STATE_UV 0
+#define XPC_ACTIVATE_MQ_MSG_INC_HEARTBEAT_UV 1
+#define XPC_ACTIVATE_MQ_MSG_OFFLINE_HEARTBEAT_UV 2
+#define XPC_ACTIVATE_MQ_MSG_ONLINE_HEARTBEAT_UV 3
+
+#define XPC_ACTIVATE_MQ_MSG_ACTIVATE_REQ_UV 4
+#define XPC_ACTIVATE_MQ_MSG_DEACTIVATE_REQ_UV 5
+
+#define XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREQUEST_UV 6
+#define XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREPLY_UV 7
+#define XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREQUEST_UV 8
+#define XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREPLY_UV 9
+
+#define XPC_ACTIVATE_MQ_MSG_MARK_ENGAGED_UV 10
+#define XPC_ACTIVATE_MQ_MSG_MARK_DISENGAGED_UV 11
+
+struct xpc_activate_mq_msg_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+};
+
+struct xpc_activate_mq_msg_heartbeat_req_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ u64 heartbeat;
+};
+
+struct xpc_activate_mq_msg_activate_req_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ unsigned long rp_gpa;
+ unsigned long activate_mq_gpa;
+};
+
+struct xpc_activate_mq_msg_deactivate_req_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ enum xp_retval reason;
+};
+
+struct xpc_activate_mq_msg_chctl_closerequest_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ short ch_number;
+ enum xp_retval reason;
+};
+
+struct xpc_activate_mq_msg_chctl_closereply_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ short ch_number;
+};
+
+struct xpc_activate_mq_msg_chctl_openrequest_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ short ch_number;
+ short entry_size; /* size of notify_mq's GRU messages */
+ short local_nentries; /* ??? Is this needed? What is? */
+};
+
+struct xpc_activate_mq_msg_chctl_openreply_uv {
+ struct xpc_activate_mq_msghdr_uv hdr;
+ short ch_number;
+ short remote_nentries; /* ??? Is this needed? What is? */
+ short local_nentries; /* ??? Is this needed? What is? */
+ unsigned long local_notify_mq_gpa;
+};
/*
* Functions registered by add_timer() or called by kernel_thread() only
* the passed argument.
*/
#define XPC_PACK_ARGS(_arg1, _arg2) \
- ((((u64) _arg1) & 0xffffffff) | \
- ((((u64) _arg2) & 0xffffffff) << 32))
+ ((((u64)_arg1) & 0xffffffff) | \
+ ((((u64)_arg2) & 0xffffffff) << 32))
-#define XPC_UNPACK_ARG1(_args) (((u64) _args) & 0xffffffff)
-#define XPC_UNPACK_ARG2(_args) ((((u64) _args) >> 32) & 0xffffffff)
+#define XPC_UNPACK_ARG1(_args) (((u64)_args) & 0xffffffff)
+#define XPC_UNPACK_ARG2(_args) ((((u64)_args) >> 32) & 0xffffffff)
/*
* Define a Get/Put value pair (pointers) used with a message queue.
*/
-struct xpc_gp {
+struct xpc_gp_sn2 {
s64 get; /* Get value */
s64 put; /* Put value */
};
#define XPC_GP_SIZE \
- L1_CACHE_ALIGN(sizeof(struct xpc_gp) * XPC_NCHANNELS)
+ L1_CACHE_ALIGN(sizeof(struct xpc_gp_sn2) * XPC_MAX_NCHANNELS)
/*
* Define a structure that contains arguments associated with opening and
*/
struct xpc_openclose_args {
u16 reason; /* reason why channel is closing */
- u16 msg_size; /* sizeof each message entry */
+ u16 entry_size; /* sizeof each message entry */
u16 remote_nentries; /* #of message entries in remote msg queue */
u16 local_nentries; /* #of message entries in local msg queue */
- u64 local_msgqueue_pa; /* physical address of local message queue */
+ unsigned long local_msgqueue_pa; /* phys addr of local message queue */
};
#define XPC_OPENCLOSE_ARGS_SIZE \
- L1_CACHE_ALIGN(sizeof(struct xpc_openclose_args) * XPC_NCHANNELS)
+ L1_CACHE_ALIGN(sizeof(struct xpc_openclose_args) * \
+ XPC_MAX_NCHANNELS)
-/* struct xpc_msg flags */
-#define XPC_M_DONE 0x01 /* msg has been received/consumed */
-#define XPC_M_READY 0x02 /* msg is ready to be sent */
-#define XPC_M_INTERRUPT 0x04 /* send interrupt when msg consumed */
+/*
+ * Structures to define a fifo singly-linked list.
+ */
-#define XPC_MSG_ADDRESS(_payload) \
- ((struct xpc_msg *)((u8 *)(_payload) - XPC_MSG_PAYLOAD_OFFSET))
+struct xpc_fifo_entry_uv {
+ struct xpc_fifo_entry_uv *next;
+};
+
+struct xpc_fifo_head_uv {
+ struct xpc_fifo_entry_uv *first;
+ struct xpc_fifo_entry_uv *last;
+ spinlock_t lock;
+ int n_entries;
+};
/*
- * Defines notify entry.
+ * Define a sn2 styled message.
+ *
+ * A user-defined message resides in the payload area. The max size of the
+ * payload is defined by the user via xpc_connect().
+ *
+ * The size of a message entry (within a message queue) must be a 128-byte
+ * cacheline sized multiple in order to facilitate the BTE transfer of messages
+ * from one message queue to another.
+ */
+struct xpc_msg_sn2 {
+ u8 flags; /* FOR XPC INTERNAL USE ONLY */
+ u8 reserved[7]; /* FOR XPC INTERNAL USE ONLY */
+ s64 number; /* FOR XPC INTERNAL USE ONLY */
+
+ u64 payload; /* user defined portion of message */
+};
+
+/* struct xpc_msg_sn2 flags */
+
+#define XPC_M_SN2_DONE 0x01 /* msg has been received/consumed */
+#define XPC_M_SN2_READY 0x02 /* msg is ready to be sent */
+#define XPC_M_SN2_INTERRUPT 0x04 /* send interrupt when msg consumed */
+
+/*
+ * The format of a uv XPC notify_mq GRU message is as follows:
+ *
+ * A user-defined message resides in the payload area. The max size of the
+ * payload is defined by the user via xpc_connect().
+ *
+ * The size of a message (payload and header) sent via the GRU must be either 1
+ * or 2 GRU_CACHE_LINE_BYTES in length.
+ */
+
+struct xpc_notify_mq_msghdr_uv {
+ union {
+ unsigned int gru_msg_hdr; /* FOR GRU INTERNAL USE ONLY */
+ struct xpc_fifo_entry_uv next; /* FOR XPC INTERNAL USE ONLY */
+ } u;
+ short partid; /* FOR XPC INTERNAL USE ONLY */
+ u8 ch_number; /* FOR XPC INTERNAL USE ONLY */
+ u8 size; /* FOR XPC INTERNAL USE ONLY */
+ unsigned int msg_slot_number; /* FOR XPC INTERNAL USE ONLY */
+};
+
+struct xpc_notify_mq_msg_uv {
+ struct xpc_notify_mq_msghdr_uv hdr;
+ unsigned long payload;
+};
+
+/*
+ * Define sn2's notify entry.
*
* This is used to notify a message's sender that their message was received
* and consumed by the intended recipient.
*/
-struct xpc_notify {
+struct xpc_notify_sn2 {
u8 type; /* type of notification */
/* the following two fields are only used if type == XPC_N_CALL */
void *key; /* pointer to user's key */
};
-/* struct xpc_notify type of notification */
+/* struct xpc_notify_sn2 type of notification */
+
+#define XPC_N_CALL 0x01 /* notify function provided by user */
-#define XPC_N_CALL 0x01 /* notify function provided by user */
+/*
+ * Define uv's version of the notify entry. It additionally is used to allocate
+ * a msg slot on the remote partition into which is copied a sent message.
+ */
+struct xpc_send_msg_slot_uv {
+ struct xpc_fifo_entry_uv next;
+ unsigned int msg_slot_number;
+ xpc_notify_func func; /* user's notify function */
+ void *key; /* pointer to user's key */
+};
/*
* Define the structure that manages all the stuff required by a channel. In
* There is an array of these structures for each remote partition. It is
* allocated at the time a partition becomes active. The array contains one
* of these structures for each potential channel connection to that partition.
+ */
+
+/*
+ * The following is sn2 only.
*
- * Each of these structures manages two message queues (circular buffers).
+ * Each channel structure manages two message queues (circular buffers).
* They are allocated at the time a channel connection is made. One of
* these message queues (local_msgqueue) holds the locally created messages
* that are destined for the remote partition. The other of these message
* new messages, by the clearing of the message flags of the acknowledged
* messages.
*/
+
+struct xpc_channel_sn2 {
+ struct xpc_openclose_args *local_openclose_args; /* args passed on */
+ /* opening or closing of channel */
+
+ void *local_msgqueue_base; /* base address of kmalloc'd space */
+ struct xpc_msg_sn2 *local_msgqueue; /* local message queue */
+ void *remote_msgqueue_base; /* base address of kmalloc'd space */
+ struct xpc_msg_sn2 *remote_msgqueue; /* cached copy of remote */
+ /* partition's local message queue */
+ unsigned long remote_msgqueue_pa; /* phys addr of remote partition's */
+ /* local message queue */
+
+ struct xpc_notify_sn2 *notify_queue;/* notify queue for messages sent */
+
+ /* various flavors of local and remote Get/Put values */
+
+ struct xpc_gp_sn2 *local_GP; /* local Get/Put values */
+ struct xpc_gp_sn2 remote_GP; /* remote Get/Put values */
+ struct xpc_gp_sn2 w_local_GP; /* working local Get/Put values */
+ struct xpc_gp_sn2 w_remote_GP; /* working remote Get/Put values */
+ s64 next_msg_to_pull; /* Put value of next msg to pull */
+
+ struct mutex msg_to_pull_mutex; /* next msg to pull serialization */
+};
+
+struct xpc_channel_uv {
+ unsigned long remote_notify_mq_gpa; /* gru phys address of remote */
+ /* partition's notify mq */
+
+ struct xpc_send_msg_slot_uv *send_msg_slots;
+ struct xpc_notify_mq_msg_uv *recv_msg_slots;
+
+ struct xpc_fifo_head_uv msg_slot_free_list;
+ struct xpc_fifo_head_uv recv_msg_list; /* deliverable payloads */
+};
+
struct xpc_channel {
short partid; /* ID of remote partition connected */
spinlock_t lock; /* lock for updating this structure */
- u32 flags; /* general flags */
+ unsigned int flags; /* general flags */
enum xp_retval reason; /* reason why channel is disconnect'g */
int reason_line; /* line# disconnect initiated from */
u16 number; /* channel # */
- u16 msg_size; /* sizeof each msg entry */
+ u16 entry_size; /* sizeof each msg entry */
u16 local_nentries; /* #of msg entries in local msg queue */
u16 remote_nentries; /* #of msg entries in remote msg queue */
- void *local_msgqueue_base; /* base address of kmalloc'd space */
- struct xpc_msg *local_msgqueue; /* local message queue */
- void *remote_msgqueue_base; /* base address of kmalloc'd space */
- struct xpc_msg *remote_msgqueue; /* cached copy of remote partition's */
- /* local message queue */
- u64 remote_msgqueue_pa; /* phys addr of remote partition's */
- /* local message queue */
-
atomic_t references; /* #of external references to queues */
atomic_t n_on_msg_allocate_wq; /* #on msg allocation wait queue */
wait_queue_head_t msg_allocate_wq; /* msg allocation wait queue */
- u8 delayed_IPI_flags; /* IPI flags received, but delayed */
+ u8 delayed_chctl_flags; /* chctl flags received, but delayed */
/* action until channel disconnected */
- /* queue of msg senders who want to be notified when msg received */
-
atomic_t n_to_notify; /* #of msg senders to notify */
- struct xpc_notify *notify_queue; /* notify queue for messages sent */
xpc_channel_func func; /* user's channel function */
void *key; /* pointer to user's key */
- struct mutex msg_to_pull_mutex; /* next msg to pull serialization */
struct completion wdisconnect_wait; /* wait for channel disconnect */
- struct xpc_openclose_args *local_openclose_args; /* args passed on */
- /* opening or closing of channel */
-
- /* various flavors of local and remote Get/Put values */
-
- struct xpc_gp *local_GP; /* local Get/Put values */
- struct xpc_gp remote_GP; /* remote Get/Put values */
- struct xpc_gp w_local_GP; /* working local Get/Put values */
- struct xpc_gp w_remote_GP; /* working remote Get/Put values */
- s64 next_msg_to_pull; /* Put value of next msg to pull */
-
/* kthread management related fields */
atomic_t kthreads_assigned; /* #of kthreads assigned to channel */
wait_queue_head_t idle_wq; /* idle kthread wait queue */
+ union {
+ struct xpc_channel_sn2 sn2;
+ struct xpc_channel_uv uv;
+ } sn;
+
} ____cacheline_aligned;
/* struct xpc_channel flags */
#define XPC_C_WDISCONNECT 0x00040000 /* waiting for channel disconnect */
/*
- * Manages channels on a partition basis. There is one of these structures
+ * The channel control flags (chctl) union consists of a 64-bit variable which
+ * is divided up into eight bytes, ordered from right to left. Byte zero
+ * pertains to channel 0, byte one to channel 1, and so on. Each channel's byte
+ * can have one or more of the chctl flags set in it.
+ */
+
+union xpc_channel_ctl_flags {
+ u64 all_flags;
+ u8 flags[XPC_MAX_NCHANNELS];
+};
+
+/* chctl flags */
+#define XPC_CHCTL_CLOSEREQUEST 0x01
+#define XPC_CHCTL_CLOSEREPLY 0x02
+#define XPC_CHCTL_OPENREQUEST 0x04
+#define XPC_CHCTL_OPENREPLY 0x08
+#define XPC_CHCTL_MSGREQUEST 0x10
+
+#define XPC_OPENCLOSE_CHCTL_FLAGS \
+ (XPC_CHCTL_CLOSEREQUEST | XPC_CHCTL_CLOSEREPLY | \
+ XPC_CHCTL_OPENREQUEST | XPC_CHCTL_OPENREPLY)
+#define XPC_MSG_CHCTL_FLAGS XPC_CHCTL_MSGREQUEST
+
+static inline int
+xpc_any_openclose_chctl_flags_set(union xpc_channel_ctl_flags *chctl)
+{
+ int ch_number;
+
+ for (ch_number = 0; ch_number < XPC_MAX_NCHANNELS; ch_number++) {
+ if (chctl->flags[ch_number] & XPC_OPENCLOSE_CHCTL_FLAGS)
+ return 1;
+ }
+ return 0;
+}
+
+static inline int
+xpc_any_msg_chctl_flags_set(union xpc_channel_ctl_flags *chctl)
+{
+ int ch_number;
+
+ for (ch_number = 0; ch_number < XPC_MAX_NCHANNELS; ch_number++) {
+ if (chctl->flags[ch_number] & XPC_MSG_CHCTL_FLAGS)
+ return 1;
+ }
+ return 0;
+}
+
+/*
+ * Manage channels on a partition basis. There is one of these structures
* for each partition (a partition will never utilize the structure that
* represents itself).
*/
+
+struct xpc_partition_sn2 {
+ unsigned long remote_amos_page_pa; /* paddr of partition's amos page */
+ int activate_IRQ_nasid; /* active partition's act/deact nasid */
+ int activate_IRQ_phys_cpuid; /* active part's act/deact phys cpuid */
+
+ unsigned long remote_vars_pa; /* phys addr of partition's vars */
+ unsigned long remote_vars_part_pa; /* paddr of partition's vars part */
+ u8 remote_vars_version; /* version# of partition's vars */
+
+ void *local_GPs_base; /* base address of kmalloc'd space */
+ struct xpc_gp_sn2 *local_GPs; /* local Get/Put values */
+ void *remote_GPs_base; /* base address of kmalloc'd space */
+ struct xpc_gp_sn2 *remote_GPs; /* copy of remote partition's local */
+ /* Get/Put values */
+ unsigned long remote_GPs_pa; /* phys addr of remote partition's local */
+ /* Get/Put values */
+
+ void *local_openclose_args_base; /* base address of kmalloc'd space */
+ struct xpc_openclose_args *local_openclose_args; /* local's args */
+ unsigned long remote_openclose_args_pa; /* phys addr of remote's args */
+
+ int notify_IRQ_nasid; /* nasid of where to send notify IRQs */
+ int notify_IRQ_phys_cpuid; /* CPUID of where to send notify IRQs */
+ char notify_IRQ_owner[8]; /* notify IRQ's owner's name */
+
+ struct amo *remote_chctl_amo_va; /* addr of remote chctl flags' amo */
+ struct amo *local_chctl_amo_va; /* address of chctl flags' amo */
+
+ struct timer_list dropped_notify_IRQ_timer; /* dropped IRQ timer */
+};
+
+struct xpc_partition_uv {
+ unsigned long remote_activate_mq_gpa; /* gru phys address of remote */
+ /* partition's activate mq */
+ spinlock_t flags_lock; /* protect updating of flags */
+ unsigned int flags; /* general flags */
+ u8 remote_act_state; /* remote partition's act_state */
+ u8 act_state_req; /* act_state request from remote partition */
+ enum xp_retval reason; /* reason for deactivate act_state request */
+ u64 heartbeat; /* incremented by remote partition */
+};
+
+/* struct xpc_partition_uv flags */
+
+#define XPC_P_HEARTBEAT_OFFLINE_UV 0x00000001
+#define XPC_P_ENGAGED_UV 0x00000002
+
+/* struct xpc_partition_uv act_state change requests */
+
+#define XPC_P_ASR_ACTIVATE_UV 0x01
+#define XPC_P_ASR_REACTIVATE_UV 0x02
+#define XPC_P_ASR_DEACTIVATE_UV 0x03
+
struct xpc_partition {
/* XPC HB infrastructure */
u8 remote_rp_version; /* version# of partition's rsvd pg */
- struct timespec remote_rp_stamp; /* time when rsvd pg was initialized */
- u64 remote_rp_pa; /* phys addr of partition's rsvd pg */
- u64 remote_vars_pa; /* phys addr of partition's vars */
- u64 remote_vars_part_pa; /* phys addr of partition's vars part */
+ unsigned long remote_rp_ts_jiffies; /* timestamp when rsvd pg setup */
+ unsigned long remote_rp_pa; /* phys addr of partition's rsvd pg */
u64 last_heartbeat; /* HB at last read */
- u64 remote_amos_page_pa; /* phys addr of partition's amos page */
- int remote_act_nasid; /* active part's act/deact nasid */
- int remote_act_phys_cpuid; /* active part's act/deact phys cpuid */
- u32 act_IRQ_rcvd; /* IRQs since activation */
+ u32 activate_IRQ_rcvd; /* IRQs since activation */
spinlock_t act_lock; /* protect updating of act_state */
u8 act_state; /* from XPC HB viewpoint */
- u8 remote_vars_version; /* version# of partition's vars */
enum xp_retval reason; /* reason partition is deactivating */
int reason_line; /* line# deactivation initiated from */
- int reactivate_nasid; /* nasid in partition to reactivate */
- unsigned long disengage_request_timeout; /* timeout in jiffies */
- struct timer_list disengage_request_timer;
+ unsigned long disengage_timeout; /* timeout in jiffies */
+ struct timer_list disengage_timer;
/* XPC infrastructure referencing and teardown control */
wait_queue_head_t teardown_wq; /* kthread waiting to teardown infra */
atomic_t references; /* #of references to infrastructure */
- /*
- * NONE OF THE PRECEDING FIELDS OF THIS STRUCTURE WILL BE CLEARED WHEN
- * XPC SETS UP THE NECESSARY INFRASTRUCTURE TO SUPPORT CROSS PARTITION
- * COMMUNICATION. ALL OF THE FOLLOWING FIELDS WILL BE CLEARED. (THE
- * 'nchannels' FIELD MUST BE THE FIRST OF THE FIELDS TO BE CLEARED.)
- */
-
u8 nchannels; /* #of defined channels supported */
atomic_t nchannels_active; /* #of channels that are not DISCONNECTED */
atomic_t nchannels_engaged; /* #of channels engaged with remote part */
struct xpc_channel *channels; /* array of channel structures */
- void *local_GPs_base; /* base address of kmalloc'd space */
- struct xpc_gp *local_GPs; /* local Get/Put values */
- void *remote_GPs_base; /* base address of kmalloc'd space */
- struct xpc_gp *remote_GPs; /* copy of remote partition's local */
- /* Get/Put values */
- u64 remote_GPs_pa; /* phys address of remote partition's local */
- /* Get/Put values */
+ /* fields used for managing channel avialability and activity */
- /* fields used to pass args when opening or closing a channel */
+ union xpc_channel_ctl_flags chctl; /* chctl flags yet to be processed */
+ spinlock_t chctl_lock; /* chctl flags lock */
- void *local_openclose_args_base; /* base address of kmalloc'd space */
- struct xpc_openclose_args *local_openclose_args; /* local's args */
void *remote_openclose_args_base; /* base address of kmalloc'd space */
struct xpc_openclose_args *remote_openclose_args; /* copy of remote's */
/* args */
- u64 remote_openclose_args_pa; /* phys addr of remote's args */
-
- /* IPI sending, receiving and handling related fields */
-
- int remote_IPI_nasid; /* nasid of where to send IPIs */
- int remote_IPI_phys_cpuid; /* phys CPU ID of where to send IPIs */
- AMO_t *remote_IPI_amo_va; /* address of remote IPI AMO_t structure */
-
- AMO_t *local_IPI_amo_va; /* address of IPI AMO_t structure */
- u64 local_IPI_amo; /* IPI amo flags yet to be handled */
- char IPI_owner[8]; /* IPI owner's name */
- struct timer_list dropped_IPI_timer; /* dropped IPI timer */
-
- spinlock_t IPI_lock; /* IPI handler lock */
/* channel manager related fields */
atomic_t channel_mgr_requests; /* #of requests to activate chan mgr */
wait_queue_head_t channel_mgr_wq; /* channel mgr's wait queue */
+ union {
+ struct xpc_partition_sn2 sn2;
+ struct xpc_partition_uv uv;
+ } sn;
+
} ____cacheline_aligned;
/* struct xpc_partition act_state values (for XPC HB) */
-#define XPC_P_INACTIVE 0x00 /* partition is not active */
-#define XPC_P_ACTIVATION_REQ 0x01 /* created thread to activate */
-#define XPC_P_ACTIVATING 0x02 /* activation thread started */
-#define XPC_P_ACTIVE 0x03 /* xpc_partition_up() was called */
-#define XPC_P_DEACTIVATING 0x04 /* partition deactivation initiated */
+#define XPC_P_AS_INACTIVE 0x00 /* partition is not active */
+#define XPC_P_AS_ACTIVATION_REQ 0x01 /* created thread to activate */
+#define XPC_P_AS_ACTIVATING 0x02 /* activation thread started */
+#define XPC_P_AS_ACTIVE 0x03 /* xpc_partition_up() was called */
+#define XPC_P_AS_DEACTIVATING 0x04 /* partition deactivation initiated */
#define XPC_DEACTIVATE_PARTITION(_p, _reason) \
xpc_deactivate_partition(__LINE__, (_p), (_reason))
/* struct xpc_partition setup_state values */
-#define XPC_P_UNSET 0x00 /* infrastructure was never setup */
-#define XPC_P_SETUP 0x01 /* infrastructure is setup */
-#define XPC_P_WTEARDOWN 0x02 /* waiting to teardown infrastructure */
-#define XPC_P_TORNDOWN 0x03 /* infrastructure is torndown */
+#define XPC_P_SS_UNSET 0x00 /* infrastructure was never setup */
+#define XPC_P_SS_SETUP 0x01 /* infrastructure is setup */
+#define XPC_P_SS_WTEARDOWN 0x02 /* waiting to teardown infrastructure */
+#define XPC_P_SS_TORNDOWN 0x03 /* infrastructure is torndown */
/*
- * struct xpc_partition IPI_timer #of seconds to wait before checking for
- * dropped IPIs. These occur whenever an IPI amo write doesn't complete until
- * after the IPI was received.
+ * struct xpc_partition_sn2's dropped notify IRQ timer is set to wait the
+ * following interval #of seconds before checking for dropped notify IRQs.
+ * These can occur whenever an IRQ's associated amo write doesn't complete
+ * until after the IRQ was received.
*/
-#define XPC_P_DROPPED_IPI_WAIT (0.25 * HZ)
+#define XPC_DROPPED_NOTIFY_IRQ_WAIT_INTERVAL (0.25 * HZ)
/* number of seconds to wait for other partitions to disengage */
-#define XPC_DISENGAGE_REQUEST_DEFAULT_TIMELIMIT 90
+#define XPC_DISENGAGE_DEFAULT_TIMELIMIT 90
-/* interval in seconds to print 'waiting disengagement' messages */
-#define XPC_DISENGAGE_PRINTMSG_INTERVAL 10
+/* interval in seconds to print 'waiting deactivation' messages */
+#define XPC_DEACTIVATE_PRINTMSG_INTERVAL 10
#define XPC_PARTID(_p) ((short)((_p) - &xpc_partitions[0]))
/* found in xpc_main.c */
extern struct device *xpc_part;
extern struct device *xpc_chan;
-extern int xpc_disengage_request_timelimit;
-extern int xpc_disengage_request_timedout;
-extern irqreturn_t xpc_notify_IRQ_handler(int, void *);
-extern void xpc_dropped_IPI_check(struct xpc_partition *);
+extern int xpc_disengage_timelimit;
+extern int xpc_disengage_timedout;
+extern int xpc_activate_IRQ_rcvd;
+extern spinlock_t xpc_activate_IRQ_rcvd_lock;
+extern wait_queue_head_t xpc_activate_IRQ_wq;
+extern void *xpc_heartbeating_to_mask;
+extern void *xpc_kzalloc_cacheline_aligned(size_t, gfp_t, void **);
extern void xpc_activate_partition(struct xpc_partition *);
extern void xpc_activate_kthreads(struct xpc_channel *, int);
extern void xpc_create_kthreads(struct xpc_channel *, int, int);
extern void xpc_disconnect_wait(int);
+extern int (*xpc_setup_partitions_sn) (void);
+extern enum xp_retval (*xpc_get_partition_rsvd_page_pa) (void *, u64 *,
+ unsigned long *,
+ size_t *);
+extern int (*xpc_setup_rsvd_page_sn) (struct xpc_rsvd_page *);
+extern void (*xpc_heartbeat_init) (void);
+extern void (*xpc_heartbeat_exit) (void);
+extern void (*xpc_increment_heartbeat) (void);
+extern void (*xpc_offline_heartbeat) (void);
+extern void (*xpc_online_heartbeat) (void);
+extern enum xp_retval (*xpc_get_remote_heartbeat) (struct xpc_partition *);
+extern enum xp_retval (*xpc_make_first_contact) (struct xpc_partition *);
+extern u64 (*xpc_get_chctl_all_flags) (struct xpc_partition *);
+extern enum xp_retval (*xpc_setup_msg_structures) (struct xpc_channel *);
+extern void (*xpc_teardown_msg_structures) (struct xpc_channel *);
+extern void (*xpc_notify_senders_of_disconnect) (struct xpc_channel *);
+extern void (*xpc_process_msg_chctl_flags) (struct xpc_partition *, int);
+extern int (*xpc_n_of_deliverable_payloads) (struct xpc_channel *);
+extern void *(*xpc_get_deliverable_payload) (struct xpc_channel *);
+extern void (*xpc_request_partition_activation) (struct xpc_rsvd_page *,
+ unsigned long, int);
+extern void (*xpc_request_partition_reactivation) (struct xpc_partition *);
+extern void (*xpc_request_partition_deactivation) (struct xpc_partition *);
+extern void (*xpc_cancel_partition_deactivation_request) (
+ struct xpc_partition *);
+extern void (*xpc_process_activate_IRQ_rcvd) (void);
+extern enum xp_retval (*xpc_setup_ch_structures_sn) (struct xpc_partition *);
+extern void (*xpc_teardown_ch_structures_sn) (struct xpc_partition *);
+
+extern void (*xpc_indicate_partition_engaged) (struct xpc_partition *);
+extern int (*xpc_partition_engaged) (short);
+extern int (*xpc_any_partition_engaged) (void);
+extern void (*xpc_indicate_partition_disengaged) (struct xpc_partition *);
+extern void (*xpc_assume_partition_disengaged) (short);
+
+extern void (*xpc_send_chctl_closerequest) (struct xpc_channel *,
+ unsigned long *);
+extern void (*xpc_send_chctl_closereply) (struct xpc_channel *,
+ unsigned long *);
+extern void (*xpc_send_chctl_openrequest) (struct xpc_channel *,
+ unsigned long *);
+extern void (*xpc_send_chctl_openreply) (struct xpc_channel *, unsigned long *);
+
+extern void (*xpc_save_remote_msgqueue_pa) (struct xpc_channel *,
+ unsigned long);
+
+extern enum xp_retval (*xpc_send_payload) (struct xpc_channel *, u32, void *,
+ u16, u8, xpc_notify_func, void *);
+extern void (*xpc_received_payload) (struct xpc_channel *, void *);
+
+/* found in xpc_sn2.c */
+extern int xpc_init_sn2(void);
+extern void xpc_exit_sn2(void);
+
+/* found in xpc_uv.c */
+extern int xpc_init_uv(void);
+extern void xpc_exit_uv(void);
/* found in xpc_partition.c */
extern int xpc_exiting;
-extern struct xpc_vars *xpc_vars;
+extern int xpc_nasid_mask_nlongs;
extern struct xpc_rsvd_page *xpc_rsvd_page;
-extern struct xpc_vars_part *xpc_vars_part;
-extern struct xpc_partition xpc_partitions[XP_MAX_PARTITIONS + 1];
-extern char *xpc_remote_copy_buffer;
-extern void *xpc_remote_copy_buffer_base;
+extern unsigned long *xpc_mach_nasids;
+extern struct xpc_partition *xpc_partitions;
extern void *xpc_kmalloc_cacheline_aligned(size_t, gfp_t, void **);
-extern struct xpc_rsvd_page *xpc_rsvd_page_init(void);
-extern void xpc_allow_IPI_ops(void);
-extern void xpc_restrict_IPI_ops(void);
-extern int xpc_identify_act_IRQ_sender(void);
+extern int xpc_setup_rsvd_page(void);
+extern void xpc_teardown_rsvd_page(void);
+extern int xpc_identify_activate_IRQ_sender(void);
extern int xpc_partition_disengaged(struct xpc_partition *);
extern enum xp_retval xpc_mark_partition_active(struct xpc_partition *);
extern void xpc_mark_partition_inactive(struct xpc_partition *);
extern void xpc_discovery(void);
-extern void xpc_check_remote_hb(void);
+extern enum xp_retval xpc_get_remote_rp(int, unsigned long *,
+ struct xpc_rsvd_page *,
+ unsigned long *);
extern void xpc_deactivate_partition(const int, struct xpc_partition *,
enum xp_retval);
extern enum xp_retval xpc_initiate_partid_to_nasids(short, void *);
/* found in xpc_channel.c */
extern void xpc_initiate_connect(int);
extern void xpc_initiate_disconnect(int);
-extern enum xp_retval xpc_initiate_allocate(short, int, u32, void **);
-extern enum xp_retval xpc_initiate_send(short, int, void *);
-extern enum xp_retval xpc_initiate_send_notify(short, int, void *,
+extern enum xp_retval xpc_allocate_msg_wait(struct xpc_channel *);
+extern enum xp_retval xpc_initiate_send(short, int, u32, void *, u16);
+extern enum xp_retval xpc_initiate_send_notify(short, int, u32, void *, u16,
xpc_notify_func, void *);
extern void xpc_initiate_received(short, int, void *);
-extern enum xp_retval xpc_setup_infrastructure(struct xpc_partition *);
-extern enum xp_retval xpc_pull_remote_vars_part(struct xpc_partition *);
-extern void xpc_process_channel_activity(struct xpc_partition *);
+extern void xpc_process_sent_chctl_flags(struct xpc_partition *);
extern void xpc_connected_callout(struct xpc_channel *);
-extern void xpc_deliver_msg(struct xpc_channel *);
+extern void xpc_deliver_payload(struct xpc_channel *);
extern void xpc_disconnect_channel(const int, struct xpc_channel *,
enum xp_retval, unsigned long *);
extern void xpc_disconnect_callout(struct xpc_channel *, enum xp_retval);
extern void xpc_partition_going_down(struct xpc_partition *, enum xp_retval);
-extern void xpc_teardown_infrastructure(struct xpc_partition *);
+
+static inline int
+xpc_hb_allowed(short partid, void *heartbeating_to_mask)
+{
+ return test_bit(partid, heartbeating_to_mask);
+}
+
+static inline int
+xpc_any_hbs_allowed(void)
+{
+ DBUG_ON(xpc_heartbeating_to_mask == NULL);
+ return !bitmap_empty(xpc_heartbeating_to_mask, xp_max_npartitions);
+}
+
+static inline void
+xpc_allow_hb(short partid)
+{
+ DBUG_ON(xpc_heartbeating_to_mask == NULL);
+ set_bit(partid, xpc_heartbeating_to_mask);
+}
+
+static inline void
+xpc_disallow_hb(short partid)
+{
+ DBUG_ON(xpc_heartbeating_to_mask == NULL);
+ clear_bit(partid, xpc_heartbeating_to_mask);
+}
+
+static inline void
+xpc_disallow_all_hbs(void)
+{
+ DBUG_ON(xpc_heartbeating_to_mask == NULL);
+ bitmap_zero(xpc_heartbeating_to_mask, xp_max_npartitions);
+}
static inline void
xpc_wakeup_channel_mgr(struct xpc_partition *part)
s32 refs = atomic_dec_return(&part->references);
DBUG_ON(refs < 0);
- if (refs == 0 && part->setup_state == XPC_P_WTEARDOWN)
+ if (refs == 0 && part->setup_state == XPC_P_SS_WTEARDOWN)
wake_up(&part->teardown_wq);
}
int setup;
atomic_inc(&part->references);
- setup = (part->setup_state == XPC_P_SETUP);
+ setup = (part->setup_state == XPC_P_SS_SETUP);
if (!setup)
xpc_part_deref(part);
(_p)->reason_line = _line; \
}
-/*
- * This next set of inlines are used to keep track of when a partition is
- * potentially engaged in accessing memory belonging to another partition.
- */
-
-static inline void
-xpc_mark_partition_engaged(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- AMO_t *amo = (AMO_t *)__va(part->remote_amos_page_pa +
- (XPC_ENGAGED_PARTITIONS_AMO *
- sizeof(AMO_t)));
-
- local_irq_save(irq_flags);
-
- /* set bit corresponding to our partid in remote partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR,
- (1UL << sn_partition_id));
- /*
- * We must always use the nofault function regardless of whether we
- * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
- * didn't, we'd never know that the other partition is down and would
- * keep sending IPIs and AMOs to it until the heartbeat times out.
- */
- (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
- variable),
- xp_nofault_PIOR_target));
-
- local_irq_restore(irq_flags);
-}
-
-static inline void
-xpc_mark_partition_disengaged(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- AMO_t *amo = (AMO_t *)__va(part->remote_amos_page_pa +
- (XPC_ENGAGED_PARTITIONS_AMO *
- sizeof(AMO_t)));
-
- local_irq_save(irq_flags);
-
- /* clear bit corresponding to our partid in remote partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
- ~(1UL << sn_partition_id));
- /*
- * We must always use the nofault function regardless of whether we
- * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
- * didn't, we'd never know that the other partition is down and would
- * keep sending IPIs and AMOs to it until the heartbeat times out.
- */
- (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
- variable),
- xp_nofault_PIOR_target));
-
- local_irq_restore(irq_flags);
-}
-
-static inline void
-xpc_request_partition_disengage(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- AMO_t *amo = (AMO_t *)__va(part->remote_amos_page_pa +
- (XPC_DISENGAGE_REQUEST_AMO * sizeof(AMO_t)));
-
- local_irq_save(irq_flags);
-
- /* set bit corresponding to our partid in remote partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR,
- (1UL << sn_partition_id));
- /*
- * We must always use the nofault function regardless of whether we
- * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
- * didn't, we'd never know that the other partition is down and would
- * keep sending IPIs and AMOs to it until the heartbeat times out.
- */
- (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
- variable),
- xp_nofault_PIOR_target));
-
- local_irq_restore(irq_flags);
-}
-
-static inline void
-xpc_cancel_partition_disengage_request(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- AMO_t *amo = (AMO_t *)__va(part->remote_amos_page_pa +
- (XPC_DISENGAGE_REQUEST_AMO * sizeof(AMO_t)));
-
- local_irq_save(irq_flags);
-
- /* clear bit corresponding to our partid in remote partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
- ~(1UL << sn_partition_id));
- /*
- * We must always use the nofault function regardless of whether we
- * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
- * didn't, we'd never know that the other partition is down and would
- * keep sending IPIs and AMOs to it until the heartbeat times out.
- */
- (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
- variable),
- xp_nofault_PIOR_target));
-
- local_irq_restore(irq_flags);
-}
-
-static inline u64
-xpc_partition_engaged(u64 partid_mask)
-{
- AMO_t *amo = xpc_vars->amos_page + XPC_ENGAGED_PARTITIONS_AMO;
-
- /* return our partition's AMO variable ANDed with partid_mask */
- return (FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_LOAD) &
- partid_mask);
-}
-
-static inline u64
-xpc_partition_disengage_requested(u64 partid_mask)
-{
- AMO_t *amo = xpc_vars->amos_page + XPC_DISENGAGE_REQUEST_AMO;
-
- /* return our partition's AMO variable ANDed with partid_mask */
- return (FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_LOAD) &
- partid_mask);
-}
-
-static inline void
-xpc_clear_partition_engaged(u64 partid_mask)
-{
- AMO_t *amo = xpc_vars->amos_page + XPC_ENGAGED_PARTITIONS_AMO;
-
- /* clear bit(s) based on partid_mask in our partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
- ~partid_mask);
-}
-
-static inline void
-xpc_clear_partition_disengage_request(u64 partid_mask)
-{
- AMO_t *amo = xpc_vars->amos_page + XPC_DISENGAGE_REQUEST_AMO;
-
- /* clear bit(s) based on partid_mask in our partition's AMO */
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
- ~partid_mask);
-}
-
-/*
- * The following set of macros and inlines are used for the sending and
- * receiving of IPIs (also known as IRQs). There are two flavors of IPIs,
- * one that is associated with partition activity (SGI_XPC_ACTIVATE) and
- * the other that is associated with channel activity (SGI_XPC_NOTIFY).
- */
-
-static inline u64
-xpc_IPI_receive(AMO_t *amo)
-{
- return FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_CLEAR);
-}
-
-static inline enum xp_retval
-xpc_IPI_send(AMO_t *amo, u64 flag, int nasid, int phys_cpuid, int vector)
-{
- int ret = 0;
- unsigned long irq_flags;
-
- local_irq_save(irq_flags);
-
- FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR, flag);
- sn_send_IPI_phys(nasid, phys_cpuid, vector, 0);
-
- /*
- * We must always use the nofault function regardless of whether we
- * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
- * didn't, we'd never know that the other partition is down and would
- * keep sending IPIs and AMOs to it until the heartbeat times out.
- */
- ret = xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->variable),
- xp_nofault_PIOR_target));
-
- local_irq_restore(irq_flags);
-
- return ((ret == 0) ? xpSuccess : xpPioReadError);
-}
-
-/*
- * IPIs associated with SGI_XPC_ACTIVATE IRQ.
- */
-
-/*
- * Flag the appropriate AMO variable and send an IPI to the specified node.
- */
-static inline void
-xpc_activate_IRQ_send(u64 amos_page_pa, int from_nasid, int to_nasid,
- int to_phys_cpuid)
-{
- int w_index = XPC_NASID_W_INDEX(from_nasid);
- int b_index = XPC_NASID_B_INDEX(from_nasid);
- AMO_t *amos = (AMO_t *)__va(amos_page_pa +
- (XPC_ACTIVATE_IRQ_AMOS * sizeof(AMO_t)));
-
- (void)xpc_IPI_send(&amos[w_index], (1UL << b_index), to_nasid,
- to_phys_cpuid, SGI_XPC_ACTIVATE);
-}
-
-static inline void
-xpc_IPI_send_activate(struct xpc_vars *vars)
-{
- xpc_activate_IRQ_send(vars->amos_page_pa, cnodeid_to_nasid(0),
- vars->act_nasid, vars->act_phys_cpuid);
-}
-
-static inline void
-xpc_IPI_send_activated(struct xpc_partition *part)
-{
- xpc_activate_IRQ_send(part->remote_amos_page_pa, cnodeid_to_nasid(0),
- part->remote_act_nasid,
- part->remote_act_phys_cpuid);
-}
-
-static inline void
-xpc_IPI_send_reactivate(struct xpc_partition *part)
-{
- xpc_activate_IRQ_send(xpc_vars->amos_page_pa, part->reactivate_nasid,
- xpc_vars->act_nasid, xpc_vars->act_phys_cpuid);
-}
-
-static inline void
-xpc_IPI_send_disengage(struct xpc_partition *part)
-{
- xpc_activate_IRQ_send(part->remote_amos_page_pa, cnodeid_to_nasid(0),
- part->remote_act_nasid,
- part->remote_act_phys_cpuid);
-}
-
-/*
- * IPIs associated with SGI_XPC_NOTIFY IRQ.
- */
-
-/*
- * Send an IPI to the remote partition that is associated with the
- * specified channel.
- */
-#define XPC_NOTIFY_IRQ_SEND(_ch, _ipi_f, _irq_f) \
- xpc_notify_IRQ_send(_ch, _ipi_f, #_ipi_f, _irq_f)
-
-static inline void
-xpc_notify_IRQ_send(struct xpc_channel *ch, u8 ipi_flag, char *ipi_flag_string,
- unsigned long *irq_flags)
-{
- struct xpc_partition *part = &xpc_partitions[ch->partid];
- enum xp_retval ret;
-
- if (likely(part->act_state != XPC_P_DEACTIVATING)) {
- ret = xpc_IPI_send(part->remote_IPI_amo_va,
- (u64)ipi_flag << (ch->number * 8),
- part->remote_IPI_nasid,
- part->remote_IPI_phys_cpuid, SGI_XPC_NOTIFY);
- dev_dbg(xpc_chan, "%s sent to partid=%d, channel=%d, ret=%d\n",
- ipi_flag_string, ch->partid, ch->number, ret);
- if (unlikely(ret != xpSuccess)) {
- if (irq_flags != NULL)
- spin_unlock_irqrestore(&ch->lock, *irq_flags);
- XPC_DEACTIVATE_PARTITION(part, ret);
- if (irq_flags != NULL)
- spin_lock_irqsave(&ch->lock, *irq_flags);
- }
- }
-}
-
-/*
- * Make it look like the remote partition, which is associated with the
- * specified channel, sent us an IPI. This faked IPI will be handled
- * by xpc_dropped_IPI_check().
- */
-#define XPC_NOTIFY_IRQ_SEND_LOCAL(_ch, _ipi_f) \
- xpc_notify_IRQ_send_local(_ch, _ipi_f, #_ipi_f)
-
-static inline void
-xpc_notify_IRQ_send_local(struct xpc_channel *ch, u8 ipi_flag,
- char *ipi_flag_string)
-{
- struct xpc_partition *part = &xpc_partitions[ch->partid];
-
- FETCHOP_STORE_OP(TO_AMO((u64)&part->local_IPI_amo_va->variable),
- FETCHOP_OR, ((u64)ipi_flag << (ch->number * 8)));
- dev_dbg(xpc_chan, "%s sent local from partid=%d, channel=%d\n",
- ipi_flag_string, ch->partid, ch->number);
-}
-
-/*
- * The sending and receiving of IPIs includes the setting of an AMO variable
- * to indicate the reason the IPI was sent. The 64-bit variable is divided
- * up into eight bytes, ordered from right to left. Byte zero pertains to
- * channel 0, byte one to channel 1, and so on. Each byte is described by
- * the following IPI flags.
- */
-
-#define XPC_IPI_CLOSEREQUEST 0x01
-#define XPC_IPI_CLOSEREPLY 0x02
-#define XPC_IPI_OPENREQUEST 0x04
-#define XPC_IPI_OPENREPLY 0x08
-#define XPC_IPI_MSGREQUEST 0x10
-
-/* given an AMO variable and a channel#, get its associated IPI flags */
-#define XPC_GET_IPI_FLAGS(_amo, _c) ((u8) (((_amo) >> ((_c) * 8)) & 0xff))
-#define XPC_SET_IPI_FLAGS(_amo, _c, _f) (_amo) |= ((u64) (_f) << ((_c) * 8))
-
-#define XPC_ANY_OPENCLOSE_IPI_FLAGS_SET(_amo) ((_amo) & 0x0f0f0f0f0f0f0f0fUL)
-#define XPC_ANY_MSG_IPI_FLAGS_SET(_amo) ((_amo) & 0x1010101010101010UL)
-
-static inline void
-xpc_IPI_send_closerequest(struct xpc_channel *ch, unsigned long *irq_flags)
-{
- struct xpc_openclose_args *args = ch->local_openclose_args;
-
- args->reason = ch->reason;
-
- XPC_NOTIFY_IRQ_SEND(ch, XPC_IPI_CLOSEREQUEST, irq_flags);
-}
-
-static inline void
-xpc_IPI_send_closereply(struct xpc_channel *ch, unsigned long *irq_flags)
-{
- XPC_NOTIFY_IRQ_SEND(ch, XPC_IPI_CLOSEREPLY, irq_flags);
-}
-
-static inline void
-xpc_IPI_send_openrequest(struct xpc_channel *ch, unsigned long *irq_flags)
-{
- struct xpc_openclose_args *args = ch->local_openclose_args;
-
- args->msg_size = ch->msg_size;
- args->local_nentries = ch->local_nentries;
-
- XPC_NOTIFY_IRQ_SEND(ch, XPC_IPI_OPENREQUEST, irq_flags);
-}
-
-static inline void
-xpc_IPI_send_openreply(struct xpc_channel *ch, unsigned long *irq_flags)
-{
- struct xpc_openclose_args *args = ch->local_openclose_args;
-
- args->remote_nentries = ch->remote_nentries;
- args->local_nentries = ch->local_nentries;
- args->local_msgqueue_pa = __pa(ch->local_msgqueue);
-
- XPC_NOTIFY_IRQ_SEND(ch, XPC_IPI_OPENREPLY, irq_flags);
-}
-
-static inline void
-xpc_IPI_send_msgrequest(struct xpc_channel *ch)
-{
- XPC_NOTIFY_IRQ_SEND(ch, XPC_IPI_MSGREQUEST, NULL);
-}
-
-static inline void
-xpc_IPI_send_local_msgrequest(struct xpc_channel *ch)
-{
- XPC_NOTIFY_IRQ_SEND_LOCAL(ch, XPC_IPI_MSGREQUEST);
-}
-
-/*
- * Memory for XPC's AMO variables is allocated by the MSPEC driver. These
- * pages are located in the lowest granule. The lowest granule uses 4k pages
- * for cached references and an alternate TLB handler to never provide a
- * cacheable mapping for the entire region. This will prevent speculative
- * reading of cached copies of our lines from being issued which will cause
- * a PI FSB Protocol error to be generated by the SHUB. For XPC, we need 64
- * AMO variables (based on XP_MAX_PARTITIONS) for message notification and an
- * additional 128 AMO variables (based on XP_NASID_MASK_WORDS) for partition
- * activation and 2 AMO variables for partition deactivation.
- */
-static inline AMO_t *
-xpc_IPI_init(int index)
-{
- AMO_t *amo = xpc_vars->amos_page + index;
-
- (void)xpc_IPI_receive(amo); /* clear AMO variable */
- return amo;
-}
-
-static inline enum xp_retval
-xpc_map_bte_errors(bte_result_t error)
-{
- return ((error == BTE_SUCCESS) ? xpSuccess : xpBteCopyError);
-}
-
-/*
- * Check to see if there is any channel activity to/from the specified
- * partition.
- */
-static inline void
-xpc_check_for_channel_activity(struct xpc_partition *part)
-{
- u64 IPI_amo;
- unsigned long irq_flags;
-
- IPI_amo = xpc_IPI_receive(part->local_IPI_amo_va);
- if (IPI_amo == 0)
- return;
-
- spin_lock_irqsave(&part->IPI_lock, irq_flags);
- part->local_IPI_amo |= IPI_amo;
- spin_unlock_irqrestore(&part->IPI_lock, irq_flags);
-
- dev_dbg(xpc_chan, "received IPI from partid=%d, IPI_amo=0x%lx\n",
- XPC_PARTID(part), IPI_amo);
-
- xpc_wakeup_channel_mgr(part);
-}
-
#endif /* _DRIVERS_MISC_SGIXP_XPC_H */
*
*/
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/cache.h>
-#include <linux/interrupt.h>
-#include <linux/mutex.h>
-#include <linux/completion.h>
-#include <asm/sn/bte.h>
-#include <asm/sn/sn_sal.h>
+#include <linux/device.h>
#include "xpc.h"
-/*
- * Guarantee that the kzalloc'd memory is cacheline aligned.
- */
-static void *
-xpc_kzalloc_cacheline_aligned(size_t size, gfp_t flags, void **base)
-{
- /* see if kzalloc will give us cachline aligned memory by default */
- *base = kzalloc(size, flags);
- if (*base == NULL)
- return NULL;
-
- if ((u64)*base == L1_CACHE_ALIGN((u64)*base))
- return *base;
-
- kfree(*base);
-
- /* nope, we'll have to do it ourselves */
- *base = kzalloc(size + L1_CACHE_BYTES, flags);
- if (*base == NULL)
- return NULL;
-
- return (void *)L1_CACHE_ALIGN((u64)*base);
-}
-
-/*
- * Set up the initial values for the XPartition Communication channels.
- */
-static void
-xpc_initialize_channels(struct xpc_partition *part, short partid)
-{
- int ch_number;
- struct xpc_channel *ch;
-
- for (ch_number = 0; ch_number < part->nchannels; ch_number++) {
- ch = &part->channels[ch_number];
-
- ch->partid = partid;
- ch->number = ch_number;
- ch->flags = XPC_C_DISCONNECTED;
-
- ch->local_GP = &part->local_GPs[ch_number];
- ch->local_openclose_args =
- &part->local_openclose_args[ch_number];
-
- atomic_set(&ch->kthreads_assigned, 0);
- atomic_set(&ch->kthreads_idle, 0);
- atomic_set(&ch->kthreads_active, 0);
-
- atomic_set(&ch->references, 0);
- atomic_set(&ch->n_to_notify, 0);
-
- spin_lock_init(&ch->lock);
- mutex_init(&ch->msg_to_pull_mutex);
- init_completion(&ch->wdisconnect_wait);
-
- atomic_set(&ch->n_on_msg_allocate_wq, 0);
- init_waitqueue_head(&ch->msg_allocate_wq);
- init_waitqueue_head(&ch->idle_wq);
- }
-}
-
-/*
- * Setup the infrastructure necessary to support XPartition Communication
- * between the specified remote partition and the local one.
- */
-enum xp_retval
-xpc_setup_infrastructure(struct xpc_partition *part)
-{
- int ret, cpuid;
- struct timer_list *timer;
- short partid = XPC_PARTID(part);
-
- /*
- * Zero out MOST of the entry for this partition. Only the fields
- * starting with `nchannels' will be zeroed. The preceding fields must
- * remain `viable' across partition ups and downs, since they may be
- * referenced during this memset() operation.
- */
- memset(&part->nchannels, 0, sizeof(struct xpc_partition) -
- offsetof(struct xpc_partition, nchannels));
-
- /*
- * Allocate all of the channel structures as a contiguous chunk of
- * memory.
- */
- part->channels = kzalloc(sizeof(struct xpc_channel) * XPC_NCHANNELS,
- GFP_KERNEL);
- if (part->channels == NULL) {
- dev_err(xpc_chan, "can't get memory for channels\n");
- return xpNoMemory;
- }
-
- part->nchannels = XPC_NCHANNELS;
-
- /* allocate all the required GET/PUT values */
-
- part->local_GPs = xpc_kzalloc_cacheline_aligned(XPC_GP_SIZE,
- GFP_KERNEL,
- &part->local_GPs_base);
- if (part->local_GPs == NULL) {
- kfree(part->channels);
- part->channels = NULL;
- dev_err(xpc_chan, "can't get memory for local get/put "
- "values\n");
- return xpNoMemory;
- }
-
- part->remote_GPs = xpc_kzalloc_cacheline_aligned(XPC_GP_SIZE,
- GFP_KERNEL,
- &part->
- remote_GPs_base);
- if (part->remote_GPs == NULL) {
- dev_err(xpc_chan, "can't get memory for remote get/put "
- "values\n");
- kfree(part->local_GPs_base);
- part->local_GPs = NULL;
- kfree(part->channels);
- part->channels = NULL;
- return xpNoMemory;
- }
-
- /* allocate all the required open and close args */
-
- part->local_openclose_args =
- xpc_kzalloc_cacheline_aligned(XPC_OPENCLOSE_ARGS_SIZE, GFP_KERNEL,
- &part->local_openclose_args_base);
- if (part->local_openclose_args == NULL) {
- dev_err(xpc_chan, "can't get memory for local connect args\n");
- kfree(part->remote_GPs_base);
- part->remote_GPs = NULL;
- kfree(part->local_GPs_base);
- part->local_GPs = NULL;
- kfree(part->channels);
- part->channels = NULL;
- return xpNoMemory;
- }
-
- part->remote_openclose_args =
- xpc_kzalloc_cacheline_aligned(XPC_OPENCLOSE_ARGS_SIZE, GFP_KERNEL,
- &part->remote_openclose_args_base);
- if (part->remote_openclose_args == NULL) {
- dev_err(xpc_chan, "can't get memory for remote connect args\n");
- kfree(part->local_openclose_args_base);
- part->local_openclose_args = NULL;
- kfree(part->remote_GPs_base);
- part->remote_GPs = NULL;
- kfree(part->local_GPs_base);
- part->local_GPs = NULL;
- kfree(part->channels);
- part->channels = NULL;
- return xpNoMemory;
- }
-
- xpc_initialize_channels(part, partid);
-
- atomic_set(&part->nchannels_active, 0);
- atomic_set(&part->nchannels_engaged, 0);
-
- /* local_IPI_amo were set to 0 by an earlier memset() */
-
- /* Initialize this partitions AMO_t structure */
- part->local_IPI_amo_va = xpc_IPI_init(partid);
-
- spin_lock_init(&part->IPI_lock);
-
- atomic_set(&part->channel_mgr_requests, 1);
- init_waitqueue_head(&part->channel_mgr_wq);
-
- sprintf(part->IPI_owner, "xpc%02d", partid);
- ret = request_irq(SGI_XPC_NOTIFY, xpc_notify_IRQ_handler, IRQF_SHARED,
- part->IPI_owner, (void *)(u64)partid);
- if (ret != 0) {
- dev_err(xpc_chan, "can't register NOTIFY IRQ handler, "
- "errno=%d\n", -ret);
- kfree(part->remote_openclose_args_base);
- part->remote_openclose_args = NULL;
- kfree(part->local_openclose_args_base);
- part->local_openclose_args = NULL;
- kfree(part->remote_GPs_base);
- part->remote_GPs = NULL;
- kfree(part->local_GPs_base);
- part->local_GPs = NULL;
- kfree(part->channels);
- part->channels = NULL;
- return xpLackOfResources;
- }
-
- /* Setup a timer to check for dropped IPIs */
- timer = &part->dropped_IPI_timer;
- init_timer(timer);
- timer->function = (void (*)(unsigned long))xpc_dropped_IPI_check;
- timer->data = (unsigned long)part;
- timer->expires = jiffies + XPC_P_DROPPED_IPI_WAIT;
- add_timer(timer);
-
- /*
- * With the setting of the partition setup_state to XPC_P_SETUP, we're
- * declaring that this partition is ready to go.
- */
- part->setup_state = XPC_P_SETUP;
-
- /*
- * Setup the per partition specific variables required by the
- * remote partition to establish channel connections with us.
- *
- * The setting of the magic # indicates that these per partition
- * specific variables are ready to be used.
- */
- xpc_vars_part[partid].GPs_pa = __pa(part->local_GPs);
- xpc_vars_part[partid].openclose_args_pa =
- __pa(part->local_openclose_args);
- xpc_vars_part[partid].IPI_amo_pa = __pa(part->local_IPI_amo_va);
- cpuid = raw_smp_processor_id(); /* any CPU in this partition will do */
- xpc_vars_part[partid].IPI_nasid = cpuid_to_nasid(cpuid);
- xpc_vars_part[partid].IPI_phys_cpuid = cpu_physical_id(cpuid);
- xpc_vars_part[partid].nchannels = part->nchannels;
- xpc_vars_part[partid].magic = XPC_VP_MAGIC1;
-
- return xpSuccess;
-}
-
-/*
- * Create a wrapper that hides the underlying mechanism for pulling a cacheline
- * (or multiple cachelines) from a remote partition.
- *
- * src must be a cacheline aligned physical address on the remote partition.
- * dst must be a cacheline aligned virtual address on this partition.
- * cnt must be an cacheline sized
- */
-static enum xp_retval
-xpc_pull_remote_cachelines(struct xpc_partition *part, void *dst,
- const void *src, size_t cnt)
-{
- bte_result_t bte_ret;
-
- DBUG_ON((u64)src != L1_CACHE_ALIGN((u64)src));
- DBUG_ON((u64)dst != L1_CACHE_ALIGN((u64)dst));
- DBUG_ON(cnt != L1_CACHE_ALIGN(cnt));
-
- if (part->act_state == XPC_P_DEACTIVATING)
- return part->reason;
-
- bte_ret = xp_bte_copy((u64)src, (u64)dst, (u64)cnt,
- (BTE_NORMAL | BTE_WACQUIRE), NULL);
- if (bte_ret == BTE_SUCCESS)
- return xpSuccess;
-
- dev_dbg(xpc_chan, "xp_bte_copy() from partition %d failed, ret=%d\n",
- XPC_PARTID(part), bte_ret);
-
- return xpc_map_bte_errors(bte_ret);
-}
-
-/*
- * Pull the remote per partition specific variables from the specified
- * partition.
- */
-enum xp_retval
-xpc_pull_remote_vars_part(struct xpc_partition *part)
-{
- u8 buffer[L1_CACHE_BYTES * 2];
- struct xpc_vars_part *pulled_entry_cacheline =
- (struct xpc_vars_part *)L1_CACHE_ALIGN((u64)buffer);
- struct xpc_vars_part *pulled_entry;
- u64 remote_entry_cacheline_pa, remote_entry_pa;
- short partid = XPC_PARTID(part);
- enum xp_retval ret;
-
- /* pull the cacheline that contains the variables we're interested in */
-
- DBUG_ON(part->remote_vars_part_pa !=
- L1_CACHE_ALIGN(part->remote_vars_part_pa));
- DBUG_ON(sizeof(struct xpc_vars_part) != L1_CACHE_BYTES / 2);
-
- remote_entry_pa = part->remote_vars_part_pa +
- sn_partition_id * sizeof(struct xpc_vars_part);
-
- remote_entry_cacheline_pa = (remote_entry_pa & ~(L1_CACHE_BYTES - 1));
-
- pulled_entry = (struct xpc_vars_part *)((u64)pulled_entry_cacheline +
- (remote_entry_pa &
- (L1_CACHE_BYTES - 1)));
-
- ret = xpc_pull_remote_cachelines(part, pulled_entry_cacheline,
- (void *)remote_entry_cacheline_pa,
- L1_CACHE_BYTES);
- if (ret != xpSuccess) {
- dev_dbg(xpc_chan, "failed to pull XPC vars_part from "
- "partition %d, ret=%d\n", partid, ret);
- return ret;
- }
-
- /* see if they've been set up yet */
-
- if (pulled_entry->magic != XPC_VP_MAGIC1 &&
- pulled_entry->magic != XPC_VP_MAGIC2) {
-
- if (pulled_entry->magic != 0) {
- dev_dbg(xpc_chan, "partition %d's XPC vars_part for "
- "partition %d has bad magic value (=0x%lx)\n",
- partid, sn_partition_id, pulled_entry->magic);
- return xpBadMagic;
- }
-
- /* they've not been initialized yet */
- return xpRetry;
- }
-
- if (xpc_vars_part[partid].magic == XPC_VP_MAGIC1) {
-
- /* validate the variables */
-
- if (pulled_entry->GPs_pa == 0 ||
- pulled_entry->openclose_args_pa == 0 ||
- pulled_entry->IPI_amo_pa == 0) {
-
- dev_err(xpc_chan, "partition %d's XPC vars_part for "
- "partition %d are not valid\n", partid,
- sn_partition_id);
- return xpInvalidAddress;
- }
-
- /* the variables we imported look to be valid */
-
- part->remote_GPs_pa = pulled_entry->GPs_pa;
- part->remote_openclose_args_pa =
- pulled_entry->openclose_args_pa;
- part->remote_IPI_amo_va =
- (AMO_t *)__va(pulled_entry->IPI_amo_pa);
- part->remote_IPI_nasid = pulled_entry->IPI_nasid;
- part->remote_IPI_phys_cpuid = pulled_entry->IPI_phys_cpuid;
-
- if (part->nchannels > pulled_entry->nchannels)
- part->nchannels = pulled_entry->nchannels;
-
- /* let the other side know that we've pulled their variables */
-
- xpc_vars_part[partid].magic = XPC_VP_MAGIC2;
- }
-
- if (pulled_entry->magic == XPC_VP_MAGIC1)
- return xpRetry;
-
- return xpSuccess;
-}
-
-/*
- * Get the IPI flags and pull the openclose args and/or remote GPs as needed.
- */
-static u64
-xpc_get_IPI_flags(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- u64 IPI_amo;
- enum xp_retval ret;
-
- /*
- * See if there are any IPI flags to be handled.
- */
-
- spin_lock_irqsave(&part->IPI_lock, irq_flags);
- IPI_amo = part->local_IPI_amo;
- if (IPI_amo != 0)
- part->local_IPI_amo = 0;
-
- spin_unlock_irqrestore(&part->IPI_lock, irq_flags);
-
- if (XPC_ANY_OPENCLOSE_IPI_FLAGS_SET(IPI_amo)) {
- ret = xpc_pull_remote_cachelines(part,
- part->remote_openclose_args,
- (void *)part->
- remote_openclose_args_pa,
- XPC_OPENCLOSE_ARGS_SIZE);
- if (ret != xpSuccess) {
- XPC_DEACTIVATE_PARTITION(part, ret);
-
- dev_dbg(xpc_chan, "failed to pull openclose args from "
- "partition %d, ret=%d\n", XPC_PARTID(part),
- ret);
-
- /* don't bother processing IPIs anymore */
- IPI_amo = 0;
- }
- }
-
- if (XPC_ANY_MSG_IPI_FLAGS_SET(IPI_amo)) {
- ret = xpc_pull_remote_cachelines(part, part->remote_GPs,
- (void *)part->remote_GPs_pa,
- XPC_GP_SIZE);
- if (ret != xpSuccess) {
- XPC_DEACTIVATE_PARTITION(part, ret);
-
- dev_dbg(xpc_chan, "failed to pull GPs from partition "
- "%d, ret=%d\n", XPC_PARTID(part), ret);
-
- /* don't bother processing IPIs anymore */
- IPI_amo = 0;
- }
- }
-
- return IPI_amo;
-}
-
-/*
- * Allocate the local message queue and the notify queue.
- */
-static enum xp_retval
-xpc_allocate_local_msgqueue(struct xpc_channel *ch)
-{
- unsigned long irq_flags;
- int nentries;
- size_t nbytes;
-
- for (nentries = ch->local_nentries; nentries > 0; nentries--) {
-
- nbytes = nentries * ch->msg_size;
- ch->local_msgqueue = xpc_kzalloc_cacheline_aligned(nbytes,
- GFP_KERNEL,
- &ch->local_msgqueue_base);
- if (ch->local_msgqueue == NULL)
- continue;
-
- nbytes = nentries * sizeof(struct xpc_notify);
- ch->notify_queue = kzalloc(nbytes, GFP_KERNEL);
- if (ch->notify_queue == NULL) {
- kfree(ch->local_msgqueue_base);
- ch->local_msgqueue = NULL;
- continue;
- }
-
- spin_lock_irqsave(&ch->lock, irq_flags);
- if (nentries < ch->local_nentries) {
- dev_dbg(xpc_chan, "nentries=%d local_nentries=%d, "
- "partid=%d, channel=%d\n", nentries,
- ch->local_nentries, ch->partid, ch->number);
-
- ch->local_nentries = nentries;
- }
- spin_unlock_irqrestore(&ch->lock, irq_flags);
- return xpSuccess;
- }
-
- dev_dbg(xpc_chan, "can't get memory for local message queue and notify "
- "queue, partid=%d, channel=%d\n", ch->partid, ch->number);
- return xpNoMemory;
-}
-
-/*
- * Allocate the cached remote message queue.
- */
-static enum xp_retval
-xpc_allocate_remote_msgqueue(struct xpc_channel *ch)
-{
- unsigned long irq_flags;
- int nentries;
- size_t nbytes;
-
- DBUG_ON(ch->remote_nentries <= 0);
-
- for (nentries = ch->remote_nentries; nentries > 0; nentries--) {
-
- nbytes = nentries * ch->msg_size;
- ch->remote_msgqueue = xpc_kzalloc_cacheline_aligned(nbytes,
- GFP_KERNEL,
- &ch->remote_msgqueue_base);
- if (ch->remote_msgqueue == NULL)
- continue;
-
- spin_lock_irqsave(&ch->lock, irq_flags);
- if (nentries < ch->remote_nentries) {
- dev_dbg(xpc_chan, "nentries=%d remote_nentries=%d, "
- "partid=%d, channel=%d\n", nentries,
- ch->remote_nentries, ch->partid, ch->number);
-
- ch->remote_nentries = nentries;
- }
- spin_unlock_irqrestore(&ch->lock, irq_flags);
- return xpSuccess;
- }
-
- dev_dbg(xpc_chan, "can't get memory for cached remote message queue, "
- "partid=%d, channel=%d\n", ch->partid, ch->number);
- return xpNoMemory;
-}
-
-/*
- * Allocate message queues and other stuff associated with a channel.
- *
- * Note: Assumes all of the channel sizes are filled in.
- */
-static enum xp_retval
-xpc_allocate_msgqueues(struct xpc_channel *ch)
-{
- unsigned long irq_flags;
- enum xp_retval ret;
-
- DBUG_ON(ch->flags & XPC_C_SETUP);
-
- ret = xpc_allocate_local_msgqueue(ch);
- if (ret != xpSuccess)
- return ret;
-
- ret = xpc_allocate_remote_msgqueue(ch);
- if (ret != xpSuccess) {
- kfree(ch->local_msgqueue_base);
- ch->local_msgqueue = NULL;
- kfree(ch->notify_queue);
- ch->notify_queue = NULL;
- return ret;
- }
-
- spin_lock_irqsave(&ch->lock, irq_flags);
- ch->flags |= XPC_C_SETUP;
- spin_unlock_irqrestore(&ch->lock, irq_flags);
-
- return xpSuccess;
-}
-
/*
* Process a connect message from a remote partition.
*
if (!(ch->flags & XPC_C_SETUP)) {
spin_unlock_irqrestore(&ch->lock, *irq_flags);
- ret = xpc_allocate_msgqueues(ch);
+ ret = xpc_setup_msg_structures(ch);
spin_lock_irqsave(&ch->lock, *irq_flags);
if (ret != xpSuccess)
XPC_DISCONNECT_CHANNEL(ch, ret, irq_flags);
+ ch->flags |= XPC_C_SETUP;
+
if (ch->flags & (XPC_C_CONNECTED | XPC_C_DISCONNECTING))
return;
- DBUG_ON(!(ch->flags & XPC_C_SETUP));
DBUG_ON(ch->local_msgqueue == NULL);
DBUG_ON(ch->remote_msgqueue == NULL);
}
if (!(ch->flags & XPC_C_OPENREPLY)) {
ch->flags |= XPC_C_OPENREPLY;
- xpc_IPI_send_openreply(ch, irq_flags);
+ xpc_send_chctl_openreply(ch, irq_flags);
}
if (!(ch->flags & XPC_C_ROPENREPLY))
return;
- DBUG_ON(ch->remote_msgqueue_pa == 0);
-
ch->flags = (XPC_C_CONNECTED | XPC_C_SETUP); /* clear all else */
dev_info(xpc_chan, "channel %d to partition %d connected\n",
spin_lock_irqsave(&ch->lock, *irq_flags);
}
-/*
- * Notify those who wanted to be notified upon delivery of their message.
- */
-static void
-xpc_notify_senders(struct xpc_channel *ch, enum xp_retval reason, s64 put)
-{
- struct xpc_notify *notify;
- u8 notify_type;
- s64 get = ch->w_remote_GP.get - 1;
-
- while (++get < put && atomic_read(&ch->n_to_notify) > 0) {
-
- notify = &ch->notify_queue[get % ch->local_nentries];
-
- /*
- * See if the notify entry indicates it was associated with
- * a message who's sender wants to be notified. It is possible
- * that it is, but someone else is doing or has done the
- * notification.
- */
- notify_type = notify->type;
- if (notify_type == 0 ||
- cmpxchg(¬ify->type, notify_type, 0) != notify_type) {
- continue;
- }
-
- DBUG_ON(notify_type != XPC_N_CALL);
-
- atomic_dec(&ch->n_to_notify);
-
- if (notify->func != NULL) {
- dev_dbg(xpc_chan, "notify->func() called, notify=0x%p, "
- "msg_number=%ld, partid=%d, channel=%d\n",
- (void *)notify, get, ch->partid, ch->number);
-
- notify->func(reason, ch->partid, ch->number,
- notify->key);
-
- dev_dbg(xpc_chan, "notify->func() returned, "
- "notify=0x%p, msg_number=%ld, partid=%d, "
- "channel=%d\n", (void *)notify, get,
- ch->partid, ch->number);
- }
- }
-}
-
-/*
- * Free up message queues and other stuff that were allocated for the specified
- * channel.
- *
- * Note: ch->reason and ch->reason_line are left set for debugging purposes,
- * they're cleared when XPC_C_DISCONNECTED is cleared.
- */
-static void
-xpc_free_msgqueues(struct xpc_channel *ch)
-{
- DBUG_ON(!spin_is_locked(&ch->lock));
- DBUG_ON(atomic_read(&ch->n_to_notify) != 0);
-
- ch->remote_msgqueue_pa = 0;
- ch->func = NULL;
- ch->key = NULL;
- ch->msg_size = 0;
- ch->local_nentries = 0;
- ch->remote_nentries = 0;
- ch->kthreads_assigned_limit = 0;
- ch->kthreads_idle_limit = 0;
-
- ch->local_GP->get = 0;
- ch->local_GP->put = 0;
- ch->remote_GP.get = 0;
- ch->remote_GP.put = 0;
- ch->w_local_GP.get = 0;
- ch->w_local_GP.put = 0;
- ch->w_remote_GP.get = 0;
- ch->w_remote_GP.put = 0;
- ch->next_msg_to_pull = 0;
-
- if (ch->flags & XPC_C_SETUP) {
- ch->flags &= ~XPC_C_SETUP;
-
- dev_dbg(xpc_chan, "ch->flags=0x%x, partid=%d, channel=%d\n",
- ch->flags, ch->partid, ch->number);
-
- kfree(ch->local_msgqueue_base);
- ch->local_msgqueue = NULL;
- kfree(ch->remote_msgqueue_base);
- ch->remote_msgqueue = NULL;
- kfree(ch->notify_queue);
- ch->notify_queue = NULL;
- }
-}
-
/*
* spin_lock_irqsave() is expected to be held on entry.
*/
DBUG_ON((ch->flags & XPC_C_CONNECTEDCALLOUT_MADE) &&
!(ch->flags & XPC_C_DISCONNECTINGCALLOUT_MADE));
- if (part->act_state == XPC_P_DEACTIVATING) {
+ if (part->act_state == XPC_P_AS_DEACTIVATING) {
/* can't proceed until the other side disengages from us */
- if (xpc_partition_engaged(1UL << ch->partid))
+ if (xpc_partition_engaged(ch->partid))
return;
} else {
if (!(ch->flags & XPC_C_CLOSEREPLY)) {
ch->flags |= XPC_C_CLOSEREPLY;
- xpc_IPI_send_closereply(ch, irq_flags);
+ xpc_send_chctl_closereply(ch, irq_flags);
}
if (!(ch->flags & XPC_C_RCLOSEREPLY))
/* wake those waiting for notify completion */
if (atomic_read(&ch->n_to_notify) > 0) {
- /* >>> we do callout while holding ch->lock */
- xpc_notify_senders(ch, ch->reason, ch->w_local_GP.put);
+ /* we do callout while holding ch->lock, callout can't block */
+ xpc_notify_senders_of_disconnect(ch);
}
/* both sides are disconnected now */
spin_lock_irqsave(&ch->lock, *irq_flags);
}
+ DBUG_ON(atomic_read(&ch->n_to_notify) != 0);
+
/* it's now safe to free the channel's message queues */
- xpc_free_msgqueues(ch);
+ xpc_teardown_msg_structures(ch);
- /* mark disconnected, clear all other flags except XPC_C_WDISCONNECT */
+ ch->func = NULL;
+ ch->key = NULL;
+ ch->entry_size = 0;
+ ch->local_nentries = 0;
+ ch->remote_nentries = 0;
+ ch->kthreads_assigned_limit = 0;
+ ch->kthreads_idle_limit = 0;
+
+ /*
+ * Mark the channel disconnected and clear all other flags, including
+ * XPC_C_SETUP (because of call to xpc_teardown_msg_structures()) but
+ * not including XPC_C_WDISCONNECT (if it was set).
+ */
ch->flags = (XPC_C_DISCONNECTED | (ch->flags & XPC_C_WDISCONNECT));
atomic_dec(&part->nchannels_active);
if (ch->flags & XPC_C_WDISCONNECT) {
/* we won't lose the CPU since we're holding ch->lock */
complete(&ch->wdisconnect_wait);
- } else if (ch->delayed_IPI_flags) {
- if (part->act_state != XPC_P_DEACTIVATING) {
- /* time to take action on any delayed IPI flags */
- spin_lock(&part->IPI_lock);
- XPC_SET_IPI_FLAGS(part->local_IPI_amo, ch->number,
- ch->delayed_IPI_flags);
- spin_unlock(&part->IPI_lock);
+ } else if (ch->delayed_chctl_flags) {
+ if (part->act_state != XPC_P_AS_DEACTIVATING) {
+ /* time to take action on any delayed chctl flags */
+ spin_lock(&part->chctl_lock);
+ part->chctl.flags[ch->number] |=
+ ch->delayed_chctl_flags;
+ spin_unlock(&part->chctl_lock);
}
- ch->delayed_IPI_flags = 0;
+ ch->delayed_chctl_flags = 0;
}
}
* Process a change in the channel's remote connection state.
*/
static void
-xpc_process_openclose_IPI(struct xpc_partition *part, int ch_number,
- u8 IPI_flags)
+xpc_process_openclose_chctl_flags(struct xpc_partition *part, int ch_number,
+ u8 chctl_flags)
{
unsigned long irq_flags;
struct xpc_openclose_args *args =
if ((ch->flags & XPC_C_DISCONNECTED) &&
(ch->flags & XPC_C_WDISCONNECT)) {
/*
- * Delay processing IPI flags until thread waiting disconnect
+ * Delay processing chctl flags until thread waiting disconnect
* has had a chance to see that the channel is disconnected.
*/
- ch->delayed_IPI_flags |= IPI_flags;
+ ch->delayed_chctl_flags |= chctl_flags;
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
- if (IPI_flags & XPC_IPI_CLOSEREQUEST) {
+ if (chctl_flags & XPC_CHCTL_CLOSEREQUEST) {
- dev_dbg(xpc_chan, "XPC_IPI_CLOSEREQUEST (reason=%d) received "
+ dev_dbg(xpc_chan, "XPC_CHCTL_CLOSEREQUEST (reason=%d) received "
"from partid=%d, channel=%d\n", args->reason,
ch->partid, ch->number);
/*
* If RCLOSEREQUEST is set, we're probably waiting for
* RCLOSEREPLY. We should find it and a ROPENREQUEST packed
- * with this RCLOSEREQUEST in the IPI_flags.
+ * with this RCLOSEREQUEST in the chctl_flags.
*/
if (ch->flags & XPC_C_RCLOSEREQUEST) {
DBUG_ON(!(ch->flags & XPC_C_CLOSEREPLY));
DBUG_ON(ch->flags & XPC_C_RCLOSEREPLY);
- DBUG_ON(!(IPI_flags & XPC_IPI_CLOSEREPLY));
- IPI_flags &= ~XPC_IPI_CLOSEREPLY;
+ DBUG_ON(!(chctl_flags & XPC_CHCTL_CLOSEREPLY));
+ chctl_flags &= ~XPC_CHCTL_CLOSEREPLY;
ch->flags |= XPC_C_RCLOSEREPLY;
/* both sides have finished disconnecting */
}
if (ch->flags & XPC_C_DISCONNECTED) {
- if (!(IPI_flags & XPC_IPI_OPENREQUEST)) {
- if ((XPC_GET_IPI_FLAGS(part->local_IPI_amo,
- ch_number) &
- XPC_IPI_OPENREQUEST)) {
-
- DBUG_ON(ch->delayed_IPI_flags != 0);
- spin_lock(&part->IPI_lock);
- XPC_SET_IPI_FLAGS(part->local_IPI_amo,
- ch_number,
- XPC_IPI_CLOSEREQUEST);
- spin_unlock(&part->IPI_lock);
+ if (!(chctl_flags & XPC_CHCTL_OPENREQUEST)) {
+ if (part->chctl.flags[ch_number] &
+ XPC_CHCTL_OPENREQUEST) {
+
+ DBUG_ON(ch->delayed_chctl_flags != 0);
+ spin_lock(&part->chctl_lock);
+ part->chctl.flags[ch_number] |=
+ XPC_CHCTL_CLOSEREQUEST;
+ spin_unlock(&part->chctl_lock);
}
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
ch->flags |= (XPC_C_CONNECTING | XPC_C_ROPENREQUEST);
}
- IPI_flags &= ~(XPC_IPI_OPENREQUEST | XPC_IPI_OPENREPLY);
+ chctl_flags &= ~(XPC_CHCTL_OPENREQUEST | XPC_CHCTL_OPENREPLY);
/*
* The meaningful CLOSEREQUEST connection state fields are:
XPC_DISCONNECT_CHANNEL(ch, reason, &irq_flags);
- DBUG_ON(IPI_flags & XPC_IPI_CLOSEREPLY);
+ DBUG_ON(chctl_flags & XPC_CHCTL_CLOSEREPLY);
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
xpc_process_disconnect(ch, &irq_flags);
}
- if (IPI_flags & XPC_IPI_CLOSEREPLY) {
+ if (chctl_flags & XPC_CHCTL_CLOSEREPLY) {
- dev_dbg(xpc_chan, "XPC_IPI_CLOSEREPLY received from partid=%d,"
- " channel=%d\n", ch->partid, ch->number);
+ dev_dbg(xpc_chan, "XPC_CHCTL_CLOSEREPLY received from partid="
+ "%d, channel=%d\n", ch->partid, ch->number);
if (ch->flags & XPC_C_DISCONNECTED) {
- DBUG_ON(part->act_state != XPC_P_DEACTIVATING);
+ DBUG_ON(part->act_state != XPC_P_AS_DEACTIVATING);
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
DBUG_ON(!(ch->flags & XPC_C_CLOSEREQUEST));
if (!(ch->flags & XPC_C_RCLOSEREQUEST)) {
- if ((XPC_GET_IPI_FLAGS(part->local_IPI_amo, ch_number)
- & XPC_IPI_CLOSEREQUEST)) {
-
- DBUG_ON(ch->delayed_IPI_flags != 0);
- spin_lock(&part->IPI_lock);
- XPC_SET_IPI_FLAGS(part->local_IPI_amo,
- ch_number,
- XPC_IPI_CLOSEREPLY);
- spin_unlock(&part->IPI_lock);
+ if (part->chctl.flags[ch_number] &
+ XPC_CHCTL_CLOSEREQUEST) {
+
+ DBUG_ON(ch->delayed_chctl_flags != 0);
+ spin_lock(&part->chctl_lock);
+ part->chctl.flags[ch_number] |=
+ XPC_CHCTL_CLOSEREPLY;
+ spin_unlock(&part->chctl_lock);
}
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
}
- if (IPI_flags & XPC_IPI_OPENREQUEST) {
+ if (chctl_flags & XPC_CHCTL_OPENREQUEST) {
- dev_dbg(xpc_chan, "XPC_IPI_OPENREQUEST (msg_size=%d, "
+ dev_dbg(xpc_chan, "XPC_CHCTL_OPENREQUEST (entry_size=%d, "
"local_nentries=%d) received from partid=%d, "
- "channel=%d\n", args->msg_size, args->local_nentries,
+ "channel=%d\n", args->entry_size, args->local_nentries,
ch->partid, ch->number);
- if (part->act_state == XPC_P_DEACTIVATING ||
+ if (part->act_state == XPC_P_AS_DEACTIVATING ||
(ch->flags & XPC_C_ROPENREQUEST)) {
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
if (ch->flags & (XPC_C_DISCONNECTING | XPC_C_WDISCONNECT)) {
- ch->delayed_IPI_flags |= XPC_IPI_OPENREQUEST;
+ ch->delayed_chctl_flags |= XPC_CHCTL_OPENREQUEST;
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
/*
* The meaningful OPENREQUEST connection state fields are:
- * msg_size = size of channel's messages in bytes
+ * entry_size = size of channel's messages in bytes
* local_nentries = remote partition's local_nentries
*/
- if (args->msg_size == 0 || args->local_nentries == 0) {
+ if (args->entry_size == 0 || args->local_nentries == 0) {
/* assume OPENREQUEST was delayed by mistake */
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
ch->remote_nentries = args->local_nentries;
if (ch->flags & XPC_C_OPENREQUEST) {
- if (args->msg_size != ch->msg_size) {
+ if (args->entry_size != ch->entry_size) {
XPC_DISCONNECT_CHANNEL(ch, xpUnequalMsgSizes,
&irq_flags);
spin_unlock_irqrestore(&ch->lock, irq_flags);
return;
}
} else {
- ch->msg_size = args->msg_size;
+ ch->entry_size = args->entry_size;
XPC_SET_REASON(ch, 0, 0);
ch->flags &= ~XPC_C_DISCONNECTED;
xpc_process_connect(ch, &irq_flags);
}
- if (IPI_flags & XPC_IPI_OPENREPLY) {
+ if (chctl_flags & XPC_CHCTL_OPENREPLY) {
- dev_dbg(xpc_chan, "XPC_IPI_OPENREPLY (local_msgqueue_pa=0x%lx, "
- "local_nentries=%d, remote_nentries=%d) received from "
- "partid=%d, channel=%d\n", args->local_msgqueue_pa,
- args->local_nentries, args->remote_nentries,
- ch->partid, ch->number);
+ dev_dbg(xpc_chan, "XPC_CHCTL_OPENREPLY (local_msgqueue_pa="
+ "0x%lx, local_nentries=%d, remote_nentries=%d) "
+ "received from partid=%d, channel=%d\n",
+ args->local_msgqueue_pa, args->local_nentries,
+ args->remote_nentries, ch->partid, ch->number);
if (ch->flags & (XPC_C_DISCONNECTING | XPC_C_DISCONNECTED)) {
spin_unlock_irqrestore(&ch->lock, irq_flags);
DBUG_ON(args->remote_nentries == 0);
ch->flags |= XPC_C_ROPENREPLY;
- ch->remote_msgqueue_pa = args->local_msgqueue_pa;
+ xpc_save_remote_msgqueue_pa(ch, args->local_msgqueue_pa);
if (args->local_nentries < ch->remote_nentries) {
- dev_dbg(xpc_chan, "XPC_IPI_OPENREPLY: new "
+ dev_dbg(xpc_chan, "XPC_CHCTL_OPENREPLY: new "
"remote_nentries=%d, old remote_nentries=%d, "
"partid=%d, channel=%d\n",
args->local_nentries, ch->remote_nentries,
ch->remote_nentries = args->local_nentries;
}
if (args->remote_nentries < ch->local_nentries) {
- dev_dbg(xpc_chan, "XPC_IPI_OPENREPLY: new "
+ dev_dbg(xpc_chan, "XPC_CHCTL_OPENREPLY: new "
"local_nentries=%d, old local_nentries=%d, "
"partid=%d, channel=%d\n",
args->remote_nentries, ch->local_nentries,
ch->local_nentries = registration->nentries;
if (ch->flags & XPC_C_ROPENREQUEST) {
- if (registration->msg_size != ch->msg_size) {
+ if (registration->entry_size != ch->entry_size) {
/* the local and remote sides aren't the same */
/*
return xpUnequalMsgSizes;
}
} else {
- ch->msg_size = registration->msg_size;
+ ch->entry_size = registration->entry_size;
XPC_SET_REASON(ch, 0, 0);
ch->flags &= ~XPC_C_DISCONNECTED;
/* initiate the connection */
ch->flags |= (XPC_C_OPENREQUEST | XPC_C_CONNECTING);
- xpc_IPI_send_openrequest(ch, &irq_flags);
+ xpc_send_chctl_openrequest(ch, &irq_flags);
xpc_process_connect(ch, &irq_flags);
return xpSuccess;
}
-/*
- * Clear some of the msg flags in the local message queue.
- */
-static inline void
-xpc_clear_local_msgqueue_flags(struct xpc_channel *ch)
+void
+xpc_process_sent_chctl_flags(struct xpc_partition *part)
{
- struct xpc_msg *msg;
- s64 get;
-
- get = ch->w_remote_GP.get;
- do {
- msg = (struct xpc_msg *)((u64)ch->local_msgqueue +
- (get % ch->local_nentries) *
- ch->msg_size);
- msg->flags = 0;
- } while (++get < ch->remote_GP.get);
-}
+ unsigned long irq_flags;
+ union xpc_channel_ctl_flags chctl;
+ struct xpc_channel *ch;
+ int ch_number;
+ u32 ch_flags;
-/*
- * Clear some of the msg flags in the remote message queue.
- */
-static inline void
-xpc_clear_remote_msgqueue_flags(struct xpc_channel *ch)
-{
- struct xpc_msg *msg;
- s64 put;
-
- put = ch->w_remote_GP.put;
- do {
- msg = (struct xpc_msg *)((u64)ch->remote_msgqueue +
- (put % ch->remote_nentries) *
- ch->msg_size);
- msg->flags = 0;
- } while (++put < ch->remote_GP.put);
-}
-
-static void
-xpc_process_msg_IPI(struct xpc_partition *part, int ch_number)
-{
- struct xpc_channel *ch = &part->channels[ch_number];
- int nmsgs_sent;
-
- ch->remote_GP = part->remote_GPs[ch_number];
-
- /* See what, if anything, has changed for each connected channel */
-
- xpc_msgqueue_ref(ch);
-
- if (ch->w_remote_GP.get == ch->remote_GP.get &&
- ch->w_remote_GP.put == ch->remote_GP.put) {
- /* nothing changed since GPs were last pulled */
- xpc_msgqueue_deref(ch);
- return;
- }
-
- if (!(ch->flags & XPC_C_CONNECTED)) {
- xpc_msgqueue_deref(ch);
- return;
- }
-
- /*
- * First check to see if messages recently sent by us have been
- * received by the other side. (The remote GET value will have
- * changed since we last looked at it.)
- */
-
- if (ch->w_remote_GP.get != ch->remote_GP.get) {
-
- /*
- * We need to notify any senders that want to be notified
- * that their sent messages have been received by their
- * intended recipients. We need to do this before updating
- * w_remote_GP.get so that we don't allocate the same message
- * queue entries prematurely (see xpc_allocate_msg()).
- */
- if (atomic_read(&ch->n_to_notify) > 0) {
- /*
- * Notify senders that messages sent have been
- * received and delivered by the other side.
- */
- xpc_notify_senders(ch, xpMsgDelivered,
- ch->remote_GP.get);
- }
-
- /*
- * Clear msg->flags in previously sent messages, so that
- * they're ready for xpc_allocate_msg().
- */
- xpc_clear_local_msgqueue_flags(ch);
-
- ch->w_remote_GP.get = ch->remote_GP.get;
-
- dev_dbg(xpc_chan, "w_remote_GP.get changed to %ld, partid=%d, "
- "channel=%d\n", ch->w_remote_GP.get, ch->partid,
- ch->number);
-
- /*
- * If anyone was waiting for message queue entries to become
- * available, wake them up.
- */
- if (atomic_read(&ch->n_on_msg_allocate_wq) > 0)
- wake_up(&ch->msg_allocate_wq);
- }
-
- /*
- * Now check for newly sent messages by the other side. (The remote
- * PUT value will have changed since we last looked at it.)
- */
-
- if (ch->w_remote_GP.put != ch->remote_GP.put) {
- /*
- * Clear msg->flags in previously received messages, so that
- * they're ready for xpc_get_deliverable_msg().
- */
- xpc_clear_remote_msgqueue_flags(ch);
-
- ch->w_remote_GP.put = ch->remote_GP.put;
-
- dev_dbg(xpc_chan, "w_remote_GP.put changed to %ld, partid=%d, "
- "channel=%d\n", ch->w_remote_GP.put, ch->partid,
- ch->number);
-
- nmsgs_sent = ch->w_remote_GP.put - ch->w_local_GP.get;
- if (nmsgs_sent > 0) {
- dev_dbg(xpc_chan, "msgs waiting to be copied and "
- "delivered=%d, partid=%d, channel=%d\n",
- nmsgs_sent, ch->partid, ch->number);
-
- if (ch->flags & XPC_C_CONNECTEDCALLOUT_MADE)
- xpc_activate_kthreads(ch, nmsgs_sent);
- }
- }
-
- xpc_msgqueue_deref(ch);
-}
-
-void
-xpc_process_channel_activity(struct xpc_partition *part)
-{
- unsigned long irq_flags;
- u64 IPI_amo, IPI_flags;
- struct xpc_channel *ch;
- int ch_number;
- u32 ch_flags;
-
- IPI_amo = xpc_get_IPI_flags(part);
+ chctl.all_flags = xpc_get_chctl_all_flags(part);
/*
* Initiate channel connections for registered channels.
ch = &part->channels[ch_number];
/*
- * Process any open or close related IPI flags, and then deal
+ * Process any open or close related chctl flags, and then deal
* with connecting or disconnecting the channel as required.
*/
- IPI_flags = XPC_GET_IPI_FLAGS(IPI_amo, ch_number);
-
- if (XPC_ANY_OPENCLOSE_IPI_FLAGS_SET(IPI_flags))
- xpc_process_openclose_IPI(part, ch_number, IPI_flags);
+ if (chctl.flags[ch_number] & XPC_OPENCLOSE_CHCTL_FLAGS) {
+ xpc_process_openclose_chctl_flags(part, ch_number,
+ chctl.flags[ch_number]);
+ }
ch_flags = ch->flags; /* need an atomic snapshot of flags */
continue;
}
- if (part->act_state == XPC_P_DEACTIVATING)
+ if (part->act_state == XPC_P_AS_DEACTIVATING)
continue;
if (!(ch_flags & XPC_C_CONNECTED)) {
}
/*
- * Process any message related IPI flags, this may involve the
- * activation of kthreads to deliver any pending messages sent
- * from the other partition.
+ * Process any message related chctl flags, this may involve
+ * the activation of kthreads to deliver any pending messages
+ * sent from the other partition.
*/
- if (XPC_ANY_MSG_IPI_FLAGS_SET(IPI_flags))
- xpc_process_msg_IPI(part, ch_number);
+ if (chctl.flags[ch_number] & XPC_MSG_CHCTL_FLAGS)
+ xpc_process_msg_chctl_flags(part, ch_number);
}
}
xpc_part_deref(part);
}
-/*
- * Teardown the infrastructure necessary to support XPartition Communication
- * between the specified remote partition and the local one.
- */
-void
-xpc_teardown_infrastructure(struct xpc_partition *part)
-{
- short partid = XPC_PARTID(part);
-
- /*
- * We start off by making this partition inaccessible to local
- * processes by marking it as no longer setup. Then we make it
- * inaccessible to remote processes by clearing the XPC per partition
- * specific variable's magic # (which indicates that these variables
- * are no longer valid) and by ignoring all XPC notify IPIs sent to
- * this partition.
- */
-
- DBUG_ON(atomic_read(&part->nchannels_engaged) != 0);
- DBUG_ON(atomic_read(&part->nchannels_active) != 0);
- DBUG_ON(part->setup_state != XPC_P_SETUP);
- part->setup_state = XPC_P_WTEARDOWN;
-
- xpc_vars_part[partid].magic = 0;
-
- free_irq(SGI_XPC_NOTIFY, (void *)(u64)partid);
-
- /*
- * Before proceeding with the teardown we have to wait until all
- * existing references cease.
- */
- wait_event(part->teardown_wq, (atomic_read(&part->references) == 0));
-
- /* now we can begin tearing down the infrastructure */
-
- part->setup_state = XPC_P_TORNDOWN;
-
- /* in case we've still got outstanding timers registered... */
- del_timer_sync(&part->dropped_IPI_timer);
-
- kfree(part->remote_openclose_args_base);
- part->remote_openclose_args = NULL;
- kfree(part->local_openclose_args_base);
- part->local_openclose_args = NULL;
- kfree(part->remote_GPs_base);
- part->remote_GPs = NULL;
- kfree(part->local_GPs_base);
- part->local_GPs = NULL;
- kfree(part->channels);
- part->channels = NULL;
- part->local_IPI_amo_va = NULL;
-}
-
/*
* Called by XP at the time of channel connection registration to cause
* XPC to establish connections to all currently active partitions.
struct xpc_partition *part;
struct xpc_channel *ch;
- DBUG_ON(ch_number < 0 || ch_number >= XPC_NCHANNELS);
+ DBUG_ON(ch_number < 0 || ch_number >= XPC_MAX_NCHANNELS);
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
part = &xpc_partitions[partid];
if (xpc_part_ref(part)) {
struct xpc_partition *part;
struct xpc_channel *ch;
- DBUG_ON(ch_number < 0 || ch_number >= XPC_NCHANNELS);
+ DBUG_ON(ch_number < 0 || ch_number >= XPC_MAX_NCHANNELS);
/* initiate the channel disconnect for every active partition */
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
part = &xpc_partitions[partid];
if (xpc_part_ref(part)) {
XPC_C_ROPENREQUEST | XPC_C_ROPENREPLY |
XPC_C_CONNECTING | XPC_C_CONNECTED);
- xpc_IPI_send_closerequest(ch, irq_flags);
+ xpc_send_chctl_closerequest(ch, irq_flags);
if (channel_was_connected)
ch->flags |= XPC_C_WASCONNECTED;
* Wait for a message entry to become available for the specified channel,
* but don't wait any longer than 1 jiffy.
*/
-static enum xp_retval
+enum xp_retval
xpc_allocate_msg_wait(struct xpc_channel *ch)
{
enum xp_retval ret;
}
/*
- * Allocate an entry for a message from the message queue associated with the
- * specified channel.
- */
-static enum xp_retval
-xpc_allocate_msg(struct xpc_channel *ch, u32 flags,
- struct xpc_msg **address_of_msg)
-{
- struct xpc_msg *msg;
- enum xp_retval ret;
- s64 put;
-
- /* this reference will be dropped in xpc_send_msg() */
- xpc_msgqueue_ref(ch);
-
- if (ch->flags & XPC_C_DISCONNECTING) {
- xpc_msgqueue_deref(ch);
- return ch->reason;
- }
- if (!(ch->flags & XPC_C_CONNECTED)) {
- xpc_msgqueue_deref(ch);
- return xpNotConnected;
- }
-
- /*
- * Get the next available message entry from the local message queue.
- * If none are available, we'll make sure that we grab the latest
- * GP values.
- */
- ret = xpTimeout;
-
- while (1) {
-
- put = ch->w_local_GP.put;
- rmb(); /* guarantee that .put loads before .get */
- if (put - ch->w_remote_GP.get < ch->local_nentries) {
-
- /* There are available message entries. We need to try
- * to secure one for ourselves. We'll do this by trying
- * to increment w_local_GP.put as long as someone else
- * doesn't beat us to it. If they do, we'll have to
- * try again.
- */
- if (cmpxchg(&ch->w_local_GP.put, put, put + 1) == put) {
- /* we got the entry referenced by put */
- break;
- }
- continue; /* try again */
- }
-
- /*
- * There aren't any available msg entries at this time.
- *
- * In waiting for a message entry to become available,
- * we set a timeout in case the other side is not
- * sending completion IPIs. This lets us fake an IPI
- * that will cause the IPI handler to fetch the latest
- * GP values as if an IPI was sent by the other side.
- */
- if (ret == xpTimeout)
- xpc_IPI_send_local_msgrequest(ch);
-
- if (flags & XPC_NOWAIT) {
- xpc_msgqueue_deref(ch);
- return xpNoWait;
- }
-
- ret = xpc_allocate_msg_wait(ch);
- if (ret != xpInterrupted && ret != xpTimeout) {
- xpc_msgqueue_deref(ch);
- return ret;
- }
- }
-
- /* get the message's address and initialize it */
- msg = (struct xpc_msg *)((u64)ch->local_msgqueue +
- (put % ch->local_nentries) * ch->msg_size);
-
- DBUG_ON(msg->flags != 0);
- msg->number = put;
-
- dev_dbg(xpc_chan, "w_local_GP.put changed to %ld; msg=0x%p, "
- "msg_number=%ld, partid=%d, channel=%d\n", put + 1,
- (void *)msg, msg->number, ch->partid, ch->number);
-
- *address_of_msg = msg;
-
- return xpSuccess;
-}
-
-/*
- * Allocate an entry for a message from the message queue associated with the
- * specified channel. NOTE that this routine can sleep waiting for a message
- * entry to become available. To not sleep, pass in the XPC_NOWAIT flag.
- *
- * Arguments:
- *
- * partid - ID of partition to which the channel is connected.
- * ch_number - channel #.
- * flags - see xpc.h for valid flags.
- * payload - address of the allocated payload area pointer (filled in on
- * return) in which the user-defined message is constructed.
- */
-enum xp_retval
-xpc_initiate_allocate(short partid, int ch_number, u32 flags, void **payload)
-{
- struct xpc_partition *part = &xpc_partitions[partid];
- enum xp_retval ret = xpUnknownReason;
- struct xpc_msg *msg = NULL;
-
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
- DBUG_ON(ch_number < 0 || ch_number >= part->nchannels);
-
- *payload = NULL;
-
- if (xpc_part_ref(part)) {
- ret = xpc_allocate_msg(&part->channels[ch_number], flags, &msg);
- xpc_part_deref(part);
-
- if (msg != NULL)
- *payload = &msg->payload;
- }
-
- return ret;
-}
-
-/*
- * Now we actually send the messages that are ready to be sent by advancing
- * the local message queue's Put value and then send an IPI to the recipient
- * partition.
- */
-static void
-xpc_send_msgs(struct xpc_channel *ch, s64 initial_put)
-{
- struct xpc_msg *msg;
- s64 put = initial_put + 1;
- int send_IPI = 0;
-
- while (1) {
-
- while (1) {
- if (put == ch->w_local_GP.put)
- break;
-
- msg = (struct xpc_msg *)((u64)ch->local_msgqueue +
- (put % ch->local_nentries) *
- ch->msg_size);
-
- if (!(msg->flags & XPC_M_READY))
- break;
-
- put++;
- }
-
- if (put == initial_put) {
- /* nothing's changed */
- break;
- }
-
- if (cmpxchg_rel(&ch->local_GP->put, initial_put, put) !=
- initial_put) {
- /* someone else beat us to it */
- DBUG_ON(ch->local_GP->put < initial_put);
- break;
- }
-
- /* we just set the new value of local_GP->put */
-
- dev_dbg(xpc_chan, "local_GP->put changed to %ld, partid=%d, "
- "channel=%d\n", put, ch->partid, ch->number);
-
- send_IPI = 1;
-
- /*
- * We need to ensure that the message referenced by
- * local_GP->put is not XPC_M_READY or that local_GP->put
- * equals w_local_GP.put, so we'll go have a look.
- */
- initial_put = put;
- }
-
- if (send_IPI)
- xpc_IPI_send_msgrequest(ch);
-}
-
-/*
- * Common code that does the actual sending of the message by advancing the
- * local message queue's Put value and sends an IPI to the partition the
- * message is being sent to.
- */
-static enum xp_retval
-xpc_send_msg(struct xpc_channel *ch, struct xpc_msg *msg, u8 notify_type,
- xpc_notify_func func, void *key)
-{
- enum xp_retval ret = xpSuccess;
- struct xpc_notify *notify = notify;
- s64 put, msg_number = msg->number;
-
- DBUG_ON(notify_type == XPC_N_CALL && func == NULL);
- DBUG_ON((((u64)msg - (u64)ch->local_msgqueue) / ch->msg_size) !=
- msg_number % ch->local_nentries);
- DBUG_ON(msg->flags & XPC_M_READY);
-
- if (ch->flags & XPC_C_DISCONNECTING) {
- /* drop the reference grabbed in xpc_allocate_msg() */
- xpc_msgqueue_deref(ch);
- return ch->reason;
- }
-
- if (notify_type != 0) {
- /*
- * Tell the remote side to send an ACK interrupt when the
- * message has been delivered.
- */
- msg->flags |= XPC_M_INTERRUPT;
-
- atomic_inc(&ch->n_to_notify);
-
- notify = &ch->notify_queue[msg_number % ch->local_nentries];
- notify->func = func;
- notify->key = key;
- notify->type = notify_type;
-
- /* >>> is a mb() needed here? */
-
- if (ch->flags & XPC_C_DISCONNECTING) {
- /*
- * An error occurred between our last error check and
- * this one. We will try to clear the type field from
- * the notify entry. If we succeed then
- * xpc_disconnect_channel() didn't already process
- * the notify entry.
- */
- if (cmpxchg(¬ify->type, notify_type, 0) ==
- notify_type) {
- atomic_dec(&ch->n_to_notify);
- ret = ch->reason;
- }
-
- /* drop the reference grabbed in xpc_allocate_msg() */
- xpc_msgqueue_deref(ch);
- return ret;
- }
- }
-
- msg->flags |= XPC_M_READY;
-
- /*
- * The preceding store of msg->flags must occur before the following
- * load of ch->local_GP->put.
- */
- mb();
-
- /* see if the message is next in line to be sent, if so send it */
-
- put = ch->local_GP->put;
- if (put == msg_number)
- xpc_send_msgs(ch, put);
-
- /* drop the reference grabbed in xpc_allocate_msg() */
- xpc_msgqueue_deref(ch);
- return ret;
-}
-
-/*
- * Send a message previously allocated using xpc_initiate_allocate() on the
- * specified channel connected to the specified partition.
+ * Send a message that contains the user's payload on the specified channel
+ * connected to the specified partition.
*
- * This routine will not wait for the message to be received, nor will
- * notification be given when it does happen. Once this routine has returned
- * the message entry allocated via xpc_initiate_allocate() is no longer
- * accessable to the caller.
+ * NOTE that this routine can sleep waiting for a message entry to become
+ * available. To not sleep, pass in the XPC_NOWAIT flag.
*
- * This routine, although called by users, does not call xpc_part_ref() to
- * ensure that the partition infrastructure is in place. It relies on the
- * fact that we called xpc_msgqueue_ref() in xpc_allocate_msg().
+ * Once sent, this routine will not wait for the message to be received, nor
+ * will notification be given when it does happen.
*
* Arguments:
*
* partid - ID of partition to which the channel is connected.
* ch_number - channel # to send message on.
- * payload - pointer to the payload area allocated via
- * xpc_initiate_allocate().
+ * flags - see xp.h for valid flags.
+ * payload - pointer to the payload which is to be sent.
+ * payload_size - size of the payload in bytes.
*/
enum xp_retval
-xpc_initiate_send(short partid, int ch_number, void *payload)
+xpc_initiate_send(short partid, int ch_number, u32 flags, void *payload,
+ u16 payload_size)
{
struct xpc_partition *part = &xpc_partitions[partid];
- struct xpc_msg *msg = XPC_MSG_ADDRESS(payload);
- enum xp_retval ret;
+ enum xp_retval ret = xpUnknownReason;
- dev_dbg(xpc_chan, "msg=0x%p, partid=%d, channel=%d\n", (void *)msg,
+ dev_dbg(xpc_chan, "payload=0x%p, partid=%d, channel=%d\n", payload,
partid, ch_number);
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
+ DBUG_ON(partid < 0 || partid >= xp_max_npartitions);
DBUG_ON(ch_number < 0 || ch_number >= part->nchannels);
- DBUG_ON(msg == NULL);
+ DBUG_ON(payload == NULL);
- ret = xpc_send_msg(&part->channels[ch_number], msg, 0, NULL, NULL);
+ if (xpc_part_ref(part)) {
+ ret = xpc_send_payload(&part->channels[ch_number], flags,
+ payload, payload_size, 0, NULL, NULL);
+ xpc_part_deref(part);
+ }
return ret;
}
/*
- * Send a message previously allocated using xpc_initiate_allocate on the
- * specified channel connected to the specified partition.
+ * Send a message that contains the user's payload on the specified channel
+ * connected to the specified partition.
+ *
+ * NOTE that this routine can sleep waiting for a message entry to become
+ * available. To not sleep, pass in the XPC_NOWAIT flag.
*
- * This routine will not wait for the message to be sent. Once this routine
- * has returned the message entry allocated via xpc_initiate_allocate() is no
- * longer accessable to the caller.
+ * This routine will not wait for the message to be sent or received.
*
* Once the remote end of the channel has received the message, the function
* passed as an argument to xpc_initiate_send_notify() will be called. This
*
* If this routine returns an error, the caller's function will NOT be called.
*
- * This routine, although called by users, does not call xpc_part_ref() to
- * ensure that the partition infrastructure is in place. It relies on the
- * fact that we called xpc_msgqueue_ref() in xpc_allocate_msg().
- *
* Arguments:
*
* partid - ID of partition to which the channel is connected.
* ch_number - channel # to send message on.
- * payload - pointer to the payload area allocated via
- * xpc_initiate_allocate().
+ * flags - see xp.h for valid flags.
+ * payload - pointer to the payload which is to be sent.
+ * payload_size - size of the payload in bytes.
* func - function to call with asynchronous notification of message
* receipt. THIS FUNCTION MUST BE NON-BLOCKING.
* key - user-defined key to be passed to the function when it's called.
*/
enum xp_retval
-xpc_initiate_send_notify(short partid, int ch_number, void *payload,
- xpc_notify_func func, void *key)
+xpc_initiate_send_notify(short partid, int ch_number, u32 flags, void *payload,
+ u16 payload_size, xpc_notify_func func, void *key)
{
struct xpc_partition *part = &xpc_partitions[partid];
- struct xpc_msg *msg = XPC_MSG_ADDRESS(payload);
- enum xp_retval ret;
+ enum xp_retval ret = xpUnknownReason;
- dev_dbg(xpc_chan, "msg=0x%p, partid=%d, channel=%d\n", (void *)msg,
+ dev_dbg(xpc_chan, "payload=0x%p, partid=%d, channel=%d\n", payload,
partid, ch_number);
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
+ DBUG_ON(partid < 0 || partid >= xp_max_npartitions);
DBUG_ON(ch_number < 0 || ch_number >= part->nchannels);
- DBUG_ON(msg == NULL);
+ DBUG_ON(payload == NULL);
DBUG_ON(func == NULL);
- ret = xpc_send_msg(&part->channels[ch_number], msg, XPC_N_CALL,
- func, key);
- return ret;
-}
-
-static struct xpc_msg *
-xpc_pull_remote_msg(struct xpc_channel *ch, s64 get)
-{
- struct xpc_partition *part = &xpc_partitions[ch->partid];
- struct xpc_msg *remote_msg, *msg;
- u32 msg_index, nmsgs;
- u64 msg_offset;
- enum xp_retval ret;
-
- if (mutex_lock_interruptible(&ch->msg_to_pull_mutex) != 0) {
- /* we were interrupted by a signal */
- return NULL;
- }
-
- while (get >= ch->next_msg_to_pull) {
-
- /* pull as many messages as are ready and able to be pulled */
-
- msg_index = ch->next_msg_to_pull % ch->remote_nentries;
-
- DBUG_ON(ch->next_msg_to_pull >= ch->w_remote_GP.put);
- nmsgs = ch->w_remote_GP.put - ch->next_msg_to_pull;
- if (msg_index + nmsgs > ch->remote_nentries) {
- /* ignore the ones that wrap the msg queue for now */
- nmsgs = ch->remote_nentries - msg_index;
- }
-
- msg_offset = msg_index * ch->msg_size;
- msg = (struct xpc_msg *)((u64)ch->remote_msgqueue + msg_offset);
- remote_msg = (struct xpc_msg *)(ch->remote_msgqueue_pa +
- msg_offset);
-
- ret = xpc_pull_remote_cachelines(part, msg, remote_msg,
- nmsgs * ch->msg_size);
- if (ret != xpSuccess) {
-
- dev_dbg(xpc_chan, "failed to pull %d msgs starting with"
- " msg %ld from partition %d, channel=%d, "
- "ret=%d\n", nmsgs, ch->next_msg_to_pull,
- ch->partid, ch->number, ret);
-
- XPC_DEACTIVATE_PARTITION(part, ret);
-
- mutex_unlock(&ch->msg_to_pull_mutex);
- return NULL;
- }
-
- ch->next_msg_to_pull += nmsgs;
+ if (xpc_part_ref(part)) {
+ ret = xpc_send_payload(&part->channels[ch_number], flags,
+ payload, payload_size, XPC_N_CALL, func,
+ key);
+ xpc_part_deref(part);
}
-
- mutex_unlock(&ch->msg_to_pull_mutex);
-
- /* return the message we were looking for */
- msg_offset = (get % ch->remote_nentries) * ch->msg_size;
- msg = (struct xpc_msg *)((u64)ch->remote_msgqueue + msg_offset);
-
- return msg;
-}
-
-/*
- * Get a message to be delivered.
- */
-static struct xpc_msg *
-xpc_get_deliverable_msg(struct xpc_channel *ch)
-{
- struct xpc_msg *msg = NULL;
- s64 get;
-
- do {
- if (ch->flags & XPC_C_DISCONNECTING)
- break;
-
- get = ch->w_local_GP.get;
- rmb(); /* guarantee that .get loads before .put */
- if (get == ch->w_remote_GP.put)
- break;
-
- /* There are messages waiting to be pulled and delivered.
- * We need to try to secure one for ourselves. We'll do this
- * by trying to increment w_local_GP.get and hope that no one
- * else beats us to it. If they do, we'll we'll simply have
- * to try again for the next one.
- */
-
- if (cmpxchg(&ch->w_local_GP.get, get, get + 1) == get) {
- /* we got the entry referenced by get */
-
- dev_dbg(xpc_chan, "w_local_GP.get changed to %ld, "
- "partid=%d, channel=%d\n", get + 1,
- ch->partid, ch->number);
-
- /* pull the message from the remote partition */
-
- msg = xpc_pull_remote_msg(ch, get);
-
- DBUG_ON(msg != NULL && msg->number != get);
- DBUG_ON(msg != NULL && (msg->flags & XPC_M_DONE));
- DBUG_ON(msg != NULL && !(msg->flags & XPC_M_READY));
-
- break;
- }
-
- } while (1);
-
- return msg;
+ return ret;
}
/*
- * Deliver a message to its intended recipient.
+ * Deliver a message's payload to its intended recipient.
*/
void
-xpc_deliver_msg(struct xpc_channel *ch)
+xpc_deliver_payload(struct xpc_channel *ch)
{
- struct xpc_msg *msg;
+ void *payload;
- msg = xpc_get_deliverable_msg(ch);
- if (msg != NULL) {
+ payload = xpc_get_deliverable_payload(ch);
+ if (payload != NULL) {
/*
* This ref is taken to protect the payload itself from being
atomic_inc(&ch->kthreads_active);
if (ch->func != NULL) {
- dev_dbg(xpc_chan, "ch->func() called, msg=0x%p, "
- "msg_number=%ld, partid=%d, channel=%d\n",
- (void *)msg, msg->number, ch->partid,
+ dev_dbg(xpc_chan, "ch->func() called, payload=0x%p "
+ "partid=%d channel=%d\n", payload, ch->partid,
ch->number);
/* deliver the message to its intended recipient */
- ch->func(xpMsgReceived, ch->partid, ch->number,
- &msg->payload, ch->key);
+ ch->func(xpMsgReceived, ch->partid, ch->number, payload,
+ ch->key);
- dev_dbg(xpc_chan, "ch->func() returned, msg=0x%p, "
- "msg_number=%ld, partid=%d, channel=%d\n",
- (void *)msg, msg->number, ch->partid,
+ dev_dbg(xpc_chan, "ch->func() returned, payload=0x%p "
+ "partid=%d channel=%d\n", payload, ch->partid,
ch->number);
}
}
/*
- * Now we actually acknowledge the messages that have been delivered and ack'd
- * by advancing the cached remote message queue's Get value and if requested
- * send an IPI to the message sender's partition.
- */
-static void
-xpc_acknowledge_msgs(struct xpc_channel *ch, s64 initial_get, u8 msg_flags)
-{
- struct xpc_msg *msg;
- s64 get = initial_get + 1;
- int send_IPI = 0;
-
- while (1) {
-
- while (1) {
- if (get == ch->w_local_GP.get)
- break;
-
- msg = (struct xpc_msg *)((u64)ch->remote_msgqueue +
- (get % ch->remote_nentries) *
- ch->msg_size);
-
- if (!(msg->flags & XPC_M_DONE))
- break;
-
- msg_flags |= msg->flags;
- get++;
- }
-
- if (get == initial_get) {
- /* nothing's changed */
- break;
- }
-
- if (cmpxchg_rel(&ch->local_GP->get, initial_get, get) !=
- initial_get) {
- /* someone else beat us to it */
- DBUG_ON(ch->local_GP->get <= initial_get);
- break;
- }
-
- /* we just set the new value of local_GP->get */
-
- dev_dbg(xpc_chan, "local_GP->get changed to %ld, partid=%d, "
- "channel=%d\n", get, ch->partid, ch->number);
-
- send_IPI = (msg_flags & XPC_M_INTERRUPT);
-
- /*
- * We need to ensure that the message referenced by
- * local_GP->get is not XPC_M_DONE or that local_GP->get
- * equals w_local_GP.get, so we'll go have a look.
- */
- initial_get = get;
- }
-
- if (send_IPI)
- xpc_IPI_send_msgrequest(ch);
-}
-
-/*
- * Acknowledge receipt of a delivered message.
- *
- * If a message has XPC_M_INTERRUPT set, send an interrupt to the partition
- * that sent the message.
+ * Acknowledge receipt of a delivered message's payload.
*
* This function, although called by users, does not call xpc_part_ref() to
* ensure that the partition infrastructure is in place. It relies on the
- * fact that we called xpc_msgqueue_ref() in xpc_deliver_msg().
+ * fact that we called xpc_msgqueue_ref() in xpc_deliver_payload().
*
* Arguments:
*
* partid - ID of partition to which the channel is connected.
* ch_number - channel # message received on.
* payload - pointer to the payload area allocated via
- * xpc_initiate_allocate().
+ * xpc_initiate_send() or xpc_initiate_send_notify().
*/
void
xpc_initiate_received(short partid, int ch_number, void *payload)
{
struct xpc_partition *part = &xpc_partitions[partid];
struct xpc_channel *ch;
- struct xpc_msg *msg = XPC_MSG_ADDRESS(payload);
- s64 get, msg_number = msg->number;
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
+ DBUG_ON(partid < 0 || partid >= xp_max_npartitions);
DBUG_ON(ch_number < 0 || ch_number >= part->nchannels);
ch = &part->channels[ch_number];
+ xpc_received_payload(ch, payload);
- dev_dbg(xpc_chan, "msg=0x%p, msg_number=%ld, partid=%d, channel=%d\n",
- (void *)msg, msg_number, ch->partid, ch->number);
-
- DBUG_ON((((u64)msg - (u64)ch->remote_msgqueue) / ch->msg_size) !=
- msg_number % ch->remote_nentries);
- DBUG_ON(msg->flags & XPC_M_DONE);
-
- msg->flags |= XPC_M_DONE;
-
- /*
- * The preceding store of msg->flags must occur before the following
- * load of ch->local_GP->get.
- */
- mb();
-
- /*
- * See if this message is next in line to be acknowledged as having
- * been delivered.
- */
- get = ch->local_GP->get;
- if (get == msg_number)
- xpc_acknowledge_msgs(ch, get, msg->flags);
-
- /* the call to xpc_msgqueue_ref() was done by xpc_deliver_msg() */
+ /* the call to xpc_msgqueue_ref() was done by xpc_deliver_payload() */
xpc_msgqueue_deref(ch);
}
*
* Caveats:
*
- * . We currently have no way to determine which nasid an IPI came
- * from. Thus, xpc_IPI_send() does a remote AMO write followed by
- * an IPI. The AMO indicates where data is to be pulled from, so
- * after the IPI arrives, the remote partition checks the AMO word.
- * The IPI can actually arrive before the AMO however, so other code
- * must periodically check for this case. Also, remote AMO operations
- * do not reliably time out. Thus we do a remote PIO read solely to
- * know whether the remote partition is down and whether we should
- * stop sending IPIs to it. This remote PIO read operation is set up
- * in a special nofault region so SAL knows to ignore (and cleanup)
- * any errors due to the remote AMO write, PIO read, and/or PIO
- * write operations.
+ * . Currently on sn2, we have no way to determine which nasid an IRQ
+ * came from. Thus, xpc_send_IRQ_sn2() does a remote amo write
+ * followed by an IPI. The amo indicates where data is to be pulled
+ * from, so after the IPI arrives, the remote partition checks the amo
+ * word. The IPI can actually arrive before the amo however, so other
+ * code must periodically check for this case. Also, remote amo
+ * operations do not reliably time out. Thus we do a remote PIO read
+ * solely to know whether the remote partition is down and whether we
+ * should stop sending IPIs to it. This remote PIO read operation is
+ * set up in a special nofault region so SAL knows to ignore (and
+ * cleanup) any errors due to the remote amo write, PIO read, and/or
+ * PIO write operations.
*
* If/when new hardware solves this IPI problem, we should abandon
* the current approach.
*
*/
-#include <linux/kernel.h>
#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/cache.h>
-#include <linux/interrupt.h>
+#include <linux/sysctl.h>
+#include <linux/device.h>
#include <linux/delay.h>
#include <linux/reboot.h>
-#include <linux/completion.h>
#include <linux/kdebug.h>
#include <linux/kthread.h>
-#include <linux/uaccess.h>
-#include <asm/sn/intr.h>
-#include <asm/sn/sn_sal.h>
#include "xpc.h"
/* define two XPC debug device structures to be used with dev_dbg() et al */
static int xpc_hb_check_min_interval = 10;
static int xpc_hb_check_max_interval = 120;
-int xpc_disengage_request_timelimit = XPC_DISENGAGE_REQUEST_DEFAULT_TIMELIMIT;
-static int xpc_disengage_request_min_timelimit; /* = 0 */
-static int xpc_disengage_request_max_timelimit = 120;
+int xpc_disengage_timelimit = XPC_DISENGAGE_DEFAULT_TIMELIMIT;
+static int xpc_disengage_min_timelimit; /* = 0 */
+static int xpc_disengage_max_timelimit = 120;
static ctl_table xpc_sys_xpc_hb_dir[] = {
{
.child = xpc_sys_xpc_hb_dir},
{
.ctl_name = CTL_UNNUMBERED,
- .procname = "disengage_request_timelimit",
- .data = &xpc_disengage_request_timelimit,
+ .procname = "disengage_timelimit",
+ .data = &xpc_disengage_timelimit,
.maxlen = sizeof(int),
.mode = 0644,
.proc_handler = &proc_dointvec_minmax,
.strategy = &sysctl_intvec,
- .extra1 = &xpc_disengage_request_min_timelimit,
- .extra2 = &xpc_disengage_request_max_timelimit},
+ .extra1 = &xpc_disengage_min_timelimit,
+ .extra2 = &xpc_disengage_max_timelimit},
{}
};
static ctl_table xpc_sys_dir[] = {
};
static struct ctl_table_header *xpc_sysctl;
-/* non-zero if any remote partition disengage request was timed out */
-int xpc_disengage_request_timedout;
+/* non-zero if any remote partition disengage was timed out */
+int xpc_disengage_timedout;
-/* #of IRQs received */
-static atomic_t xpc_act_IRQ_rcvd;
+/* #of activate IRQs received and not yet processed */
+int xpc_activate_IRQ_rcvd;
+DEFINE_SPINLOCK(xpc_activate_IRQ_rcvd_lock);
/* IRQ handler notifies this wait queue on receipt of an IRQ */
-static DECLARE_WAIT_QUEUE_HEAD(xpc_act_IRQ_wq);
+DECLARE_WAIT_QUEUE_HEAD(xpc_activate_IRQ_wq);
static unsigned long xpc_hb_check_timeout;
+static struct timer_list xpc_hb_timer;
+void *xpc_heartbeating_to_mask;
/* notification that the xpc_hb_checker thread has exited */
static DECLARE_COMPLETION(xpc_hb_checker_exited);
/* notification that the xpc_discovery thread has exited */
static DECLARE_COMPLETION(xpc_discovery_exited);
-static struct timer_list xpc_hb_timer;
-
static void xpc_kthread_waitmsgs(struct xpc_partition *, struct xpc_channel *);
static int xpc_system_reboot(struct notifier_block *, unsigned long, void *);
.notifier_call = xpc_system_die,
};
+int (*xpc_setup_partitions_sn) (void);
+enum xp_retval (*xpc_get_partition_rsvd_page_pa) (void *buf, u64 *cookie,
+ unsigned long *rp_pa,
+ size_t *len);
+int (*xpc_setup_rsvd_page_sn) (struct xpc_rsvd_page *rp);
+void (*xpc_heartbeat_init) (void);
+void (*xpc_heartbeat_exit) (void);
+void (*xpc_increment_heartbeat) (void);
+void (*xpc_offline_heartbeat) (void);
+void (*xpc_online_heartbeat) (void);
+enum xp_retval (*xpc_get_remote_heartbeat) (struct xpc_partition *part);
+
+enum xp_retval (*xpc_make_first_contact) (struct xpc_partition *part);
+void (*xpc_notify_senders_of_disconnect) (struct xpc_channel *ch);
+u64 (*xpc_get_chctl_all_flags) (struct xpc_partition *part);
+enum xp_retval (*xpc_setup_msg_structures) (struct xpc_channel *ch);
+void (*xpc_teardown_msg_structures) (struct xpc_channel *ch);
+void (*xpc_process_msg_chctl_flags) (struct xpc_partition *part, int ch_number);
+int (*xpc_n_of_deliverable_payloads) (struct xpc_channel *ch);
+void *(*xpc_get_deliverable_payload) (struct xpc_channel *ch);
+
+void (*xpc_request_partition_activation) (struct xpc_rsvd_page *remote_rp,
+ unsigned long remote_rp_pa,
+ int nasid);
+void (*xpc_request_partition_reactivation) (struct xpc_partition *part);
+void (*xpc_request_partition_deactivation) (struct xpc_partition *part);
+void (*xpc_cancel_partition_deactivation_request) (struct xpc_partition *part);
+
+void (*xpc_process_activate_IRQ_rcvd) (void);
+enum xp_retval (*xpc_setup_ch_structures_sn) (struct xpc_partition *part);
+void (*xpc_teardown_ch_structures_sn) (struct xpc_partition *part);
+
+void (*xpc_indicate_partition_engaged) (struct xpc_partition *part);
+int (*xpc_partition_engaged) (short partid);
+int (*xpc_any_partition_engaged) (void);
+void (*xpc_indicate_partition_disengaged) (struct xpc_partition *part);
+void (*xpc_assume_partition_disengaged) (short partid);
+
+void (*xpc_send_chctl_closerequest) (struct xpc_channel *ch,
+ unsigned long *irq_flags);
+void (*xpc_send_chctl_closereply) (struct xpc_channel *ch,
+ unsigned long *irq_flags);
+void (*xpc_send_chctl_openrequest) (struct xpc_channel *ch,
+ unsigned long *irq_flags);
+void (*xpc_send_chctl_openreply) (struct xpc_channel *ch,
+ unsigned long *irq_flags);
+
+void (*xpc_save_remote_msgqueue_pa) (struct xpc_channel *ch,
+ unsigned long msgqueue_pa);
+
+enum xp_retval (*xpc_send_payload) (struct xpc_channel *ch, u32 flags,
+ void *payload, u16 payload_size,
+ u8 notify_type, xpc_notify_func func,
+ void *key);
+void (*xpc_received_payload) (struct xpc_channel *ch, void *payload);
+
/*
- * Timer function to enforce the timelimit on the partition disengage request.
+ * Timer function to enforce the timelimit on the partition disengage.
*/
static void
-xpc_timeout_partition_disengage_request(unsigned long data)
+xpc_timeout_partition_disengage(unsigned long data)
{
struct xpc_partition *part = (struct xpc_partition *)data;
- DBUG_ON(time_before(jiffies, part->disengage_request_timeout));
+ DBUG_ON(time_is_after_jiffies(part->disengage_timeout));
(void)xpc_partition_disengaged(part);
- DBUG_ON(part->disengage_request_timeout != 0);
- DBUG_ON(xpc_partition_engaged(1UL << XPC_PARTID(part)) != 0);
-}
-
-/*
- * Notify the heartbeat check thread that an IRQ has been received.
- */
-static irqreturn_t
-xpc_act_IRQ_handler(int irq, void *dev_id)
-{
- atomic_inc(&xpc_act_IRQ_rcvd);
- wake_up_interruptible(&xpc_act_IRQ_wq);
- return IRQ_HANDLED;
+ DBUG_ON(part->disengage_timeout != 0);
+ DBUG_ON(xpc_partition_engaged(XPC_PARTID(part)));
}
/*
static void
xpc_hb_beater(unsigned long dummy)
{
- xpc_vars->heartbeat++;
+ xpc_increment_heartbeat();
- if (time_after_eq(jiffies, xpc_hb_check_timeout))
- wake_up_interruptible(&xpc_act_IRQ_wq);
+ if (time_is_before_eq_jiffies(xpc_hb_check_timeout))
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
xpc_hb_timer.expires = jiffies + (xpc_hb_interval * HZ);
add_timer(&xpc_hb_timer);
}
+static void
+xpc_start_hb_beater(void)
+{
+ xpc_heartbeat_init();
+ init_timer(&xpc_hb_timer);
+ xpc_hb_timer.function = xpc_hb_beater;
+ xpc_hb_beater(0);
+}
+
+static void
+xpc_stop_hb_beater(void)
+{
+ del_timer_sync(&xpc_hb_timer);
+ xpc_heartbeat_exit();
+}
+
+/*
+ * At periodic intervals, scan through all active partitions and ensure
+ * their heartbeat is still active. If not, the partition is deactivated.
+ */
+static void
+xpc_check_remote_hb(void)
+{
+ struct xpc_partition *part;
+ short partid;
+ enum xp_retval ret;
+
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
+
+ if (xpc_exiting)
+ break;
+
+ if (partid == xp_partition_id)
+ continue;
+
+ part = &xpc_partitions[partid];
+
+ if (part->act_state == XPC_P_AS_INACTIVE ||
+ part->act_state == XPC_P_AS_DEACTIVATING) {
+ continue;
+ }
+
+ ret = xpc_get_remote_heartbeat(part);
+ if (ret != xpSuccess)
+ XPC_DEACTIVATE_PARTITION(part, ret);
+ }
+}
+
/*
* This thread is responsible for nearly all of the partition
* activation/deactivation.
static int
xpc_hb_checker(void *ignore)
{
- int last_IRQ_count = 0;
- int new_IRQ_count;
int force_IRQ = 0;
/* this thread was marked active by xpc_hb_init() */
/* set our heartbeating to other partitions into motion */
xpc_hb_check_timeout = jiffies + (xpc_hb_check_interval * HZ);
- xpc_hb_beater(0);
+ xpc_start_hb_beater();
while (!xpc_exiting) {
dev_dbg(xpc_part, "woke up with %d ticks rem; %d IRQs have "
"been received\n",
(int)(xpc_hb_check_timeout - jiffies),
- atomic_read(&xpc_act_IRQ_rcvd) - last_IRQ_count);
+ xpc_activate_IRQ_rcvd);
/* checking of remote heartbeats is skewed by IRQ handling */
- if (time_after_eq(jiffies, xpc_hb_check_timeout)) {
+ if (time_is_before_eq_jiffies(xpc_hb_check_timeout)) {
+ xpc_hb_check_timeout = jiffies +
+ (xpc_hb_check_interval * HZ);
+
dev_dbg(xpc_part, "checking remote heartbeats\n");
xpc_check_remote_hb();
/*
- * We need to periodically recheck to ensure no
- * IPI/AMO pairs have been missed. That check
- * must always reset xpc_hb_check_timeout.
+ * On sn2 we need to periodically recheck to ensure no
+ * IRQ/amo pairs have been missed.
*/
- force_IRQ = 1;
+ if (is_shub())
+ force_IRQ = 1;
}
/* check for outstanding IRQs */
- new_IRQ_count = atomic_read(&xpc_act_IRQ_rcvd);
- if (last_IRQ_count < new_IRQ_count || force_IRQ != 0) {
+ if (xpc_activate_IRQ_rcvd > 0 || force_IRQ != 0) {
force_IRQ = 0;
-
- dev_dbg(xpc_part, "found an IRQ to process; will be "
- "resetting xpc_hb_check_timeout\n");
-
- last_IRQ_count += xpc_identify_act_IRQ_sender();
- if (last_IRQ_count < new_IRQ_count) {
- /* retry once to help avoid missing AMO */
- (void)xpc_identify_act_IRQ_sender();
- }
- last_IRQ_count = new_IRQ_count;
-
- xpc_hb_check_timeout = jiffies +
- (xpc_hb_check_interval * HZ);
+ dev_dbg(xpc_part, "processing activate IRQs "
+ "received\n");
+ xpc_process_activate_IRQ_rcvd();
}
/* wait for IRQ or timeout */
- (void)wait_event_interruptible(xpc_act_IRQ_wq,
- (last_IRQ_count <
- atomic_read(&xpc_act_IRQ_rcvd)
- || time_after_eq(jiffies,
- xpc_hb_check_timeout) ||
+ (void)wait_event_interruptible(xpc_activate_IRQ_wq,
+ (time_is_before_eq_jiffies(
+ xpc_hb_check_timeout) ||
+ xpc_activate_IRQ_rcvd > 0 ||
xpc_exiting));
}
+ xpc_stop_hb_beater();
+
dev_dbg(xpc_part, "heartbeat checker is exiting\n");
/* mark this thread as having exited */
return 0;
}
-/*
- * Establish first contact with the remote partititon. This involves pulling
- * the XPC per partition variables from the remote partition and waiting for
- * the remote partition to pull ours.
- */
-static enum xp_retval
-xpc_make_first_contact(struct xpc_partition *part)
-{
- enum xp_retval ret;
-
- while ((ret = xpc_pull_remote_vars_part(part)) != xpSuccess) {
- if (ret != xpRetry) {
- XPC_DEACTIVATE_PARTITION(part, ret);
- return ret;
- }
-
- dev_dbg(xpc_chan, "waiting to make first contact with "
- "partition %d\n", XPC_PARTID(part));
-
- /* wait a 1/4 of a second or so */
- (void)msleep_interruptible(250);
-
- if (part->act_state == XPC_P_DEACTIVATING)
- return part->reason;
- }
-
- return xpc_mark_partition_active(part);
-}
-
/*
* The first kthread assigned to a newly activated partition is the one
- * created by XPC HB with which it calls xpc_partition_up(). XPC hangs on to
+ * created by XPC HB with which it calls xpc_activating(). XPC hangs on to
* that kthread until the partition is brought down, at which time that kthread
* returns back to XPC HB. (The return of that kthread will signify to XPC HB
* that XPC has dismantled all communication infrastructure for the associated
static void
xpc_channel_mgr(struct xpc_partition *part)
{
- while (part->act_state != XPC_P_DEACTIVATING ||
+ while (part->act_state != XPC_P_AS_DEACTIVATING ||
atomic_read(&part->nchannels_active) > 0 ||
!xpc_partition_disengaged(part)) {
- xpc_process_channel_activity(part);
+ xpc_process_sent_chctl_flags(part);
/*
* Wait until we've been requested to activate kthreads or
atomic_dec(&part->channel_mgr_requests);
(void)wait_event_interruptible(part->channel_mgr_wq,
(atomic_read(&part->channel_mgr_requests) > 0 ||
- part->local_IPI_amo != 0 ||
- (part->act_state == XPC_P_DEACTIVATING &&
+ part->chctl.all_flags != 0 ||
+ (part->act_state == XPC_P_AS_DEACTIVATING &&
atomic_read(&part->nchannels_active) == 0 &&
xpc_partition_disengaged(part))));
atomic_set(&part->channel_mgr_requests, 1);
}
/*
- * When XPC HB determines that a partition has come up, it will create a new
- * kthread and that kthread will call this function to attempt to set up the
- * basic infrastructure used for Cross Partition Communication with the newly
- * upped partition.
- *
- * The kthread that was created by XPC HB and which setup the XPC
- * infrastructure will remain assigned to the partition until the partition
- * goes down. At which time the kthread will teardown the XPC infrastructure
- * and then exit.
- *
- * XPC HB will put the remote partition's XPC per partition specific variables
- * physical address into xpc_partitions[partid].remote_vars_part_pa prior to
- * calling xpc_partition_up().
+ * Guarantee that the kzalloc'd memory is cacheline aligned.
*/
-static void
-xpc_partition_up(struct xpc_partition *part)
+void *
+xpc_kzalloc_cacheline_aligned(size_t size, gfp_t flags, void **base)
+{
+ /* see if kzalloc will give us cachline aligned memory by default */
+ *base = kzalloc(size, flags);
+ if (*base == NULL)
+ return NULL;
+
+ if ((u64)*base == L1_CACHE_ALIGN((u64)*base))
+ return *base;
+
+ kfree(*base);
+
+ /* nope, we'll have to do it ourselves */
+ *base = kzalloc(size + L1_CACHE_BYTES, flags);
+ if (*base == NULL)
+ return NULL;
+
+ return (void *)L1_CACHE_ALIGN((u64)*base);
+}
+
+/*
+ * Setup the channel structures necessary to support XPartition Communication
+ * between the specified remote partition and the local one.
+ */
+static enum xp_retval
+xpc_setup_ch_structures(struct xpc_partition *part)
{
+ enum xp_retval ret;
+ int ch_number;
+ struct xpc_channel *ch;
+ short partid = XPC_PARTID(part);
+
+ /*
+ * Allocate all of the channel structures as a contiguous chunk of
+ * memory.
+ */
DBUG_ON(part->channels != NULL);
+ part->channels = kzalloc(sizeof(struct xpc_channel) * XPC_MAX_NCHANNELS,
+ GFP_KERNEL);
+ if (part->channels == NULL) {
+ dev_err(xpc_chan, "can't get memory for channels\n");
+ return xpNoMemory;
+ }
- dev_dbg(xpc_chan, "activating partition %d\n", XPC_PARTID(part));
+ /* allocate the remote open and close args */
- if (xpc_setup_infrastructure(part) != xpSuccess)
- return;
+ part->remote_openclose_args =
+ xpc_kzalloc_cacheline_aligned(XPC_OPENCLOSE_ARGS_SIZE,
+ GFP_KERNEL, &part->
+ remote_openclose_args_base);
+ if (part->remote_openclose_args == NULL) {
+ dev_err(xpc_chan, "can't get memory for remote connect args\n");
+ ret = xpNoMemory;
+ goto out_1;
+ }
+
+ part->chctl.all_flags = 0;
+ spin_lock_init(&part->chctl_lock);
+
+ atomic_set(&part->channel_mgr_requests, 1);
+ init_waitqueue_head(&part->channel_mgr_wq);
+
+ part->nchannels = XPC_MAX_NCHANNELS;
+
+ atomic_set(&part->nchannels_active, 0);
+ atomic_set(&part->nchannels_engaged, 0);
+
+ for (ch_number = 0; ch_number < part->nchannels; ch_number++) {
+ ch = &part->channels[ch_number];
+
+ ch->partid = partid;
+ ch->number = ch_number;
+ ch->flags = XPC_C_DISCONNECTED;
+
+ atomic_set(&ch->kthreads_assigned, 0);
+ atomic_set(&ch->kthreads_idle, 0);
+ atomic_set(&ch->kthreads_active, 0);
+
+ atomic_set(&ch->references, 0);
+ atomic_set(&ch->n_to_notify, 0);
+
+ spin_lock_init(&ch->lock);
+ init_completion(&ch->wdisconnect_wait);
+
+ atomic_set(&ch->n_on_msg_allocate_wq, 0);
+ init_waitqueue_head(&ch->msg_allocate_wq);
+ init_waitqueue_head(&ch->idle_wq);
+ }
+
+ ret = xpc_setup_ch_structures_sn(part);
+ if (ret != xpSuccess)
+ goto out_2;
+
+ /*
+ * With the setting of the partition setup_state to XPC_P_SS_SETUP,
+ * we're declaring that this partition is ready to go.
+ */
+ part->setup_state = XPC_P_SS_SETUP;
+
+ return xpSuccess;
+
+ /* setup of ch structures failed */
+out_2:
+ kfree(part->remote_openclose_args_base);
+ part->remote_openclose_args = NULL;
+out_1:
+ kfree(part->channels);
+ part->channels = NULL;
+ return ret;
+}
+
+/*
+ * Teardown the channel structures necessary to support XPartition Communication
+ * between the specified remote partition and the local one.
+ */
+static void
+xpc_teardown_ch_structures(struct xpc_partition *part)
+{
+ DBUG_ON(atomic_read(&part->nchannels_engaged) != 0);
+ DBUG_ON(atomic_read(&part->nchannels_active) != 0);
/*
- * The kthread that XPC HB called us with will become the
- * channel manager for this partition. It will not return
- * back to XPC HB until the partition's XPC infrastructure
- * has been dismantled.
+ * Make this partition inaccessible to local processes by marking it
+ * as no longer setup. Then wait before proceeding with the teardown
+ * until all existing references cease.
*/
+ DBUG_ON(part->setup_state != XPC_P_SS_SETUP);
+ part->setup_state = XPC_P_SS_WTEARDOWN;
- (void)xpc_part_ref(part); /* this will always succeed */
+ wait_event(part->teardown_wq, (atomic_read(&part->references) == 0));
- if (xpc_make_first_contact(part) == xpSuccess)
- xpc_channel_mgr(part);
+ /* now we can begin tearing down the infrastructure */
- xpc_part_deref(part);
+ xpc_teardown_ch_structures_sn(part);
- xpc_teardown_infrastructure(part);
+ kfree(part->remote_openclose_args_base);
+ part->remote_openclose_args = NULL;
+ kfree(part->channels);
+ part->channels = NULL;
+
+ part->setup_state = XPC_P_SS_TORNDOWN;
}
+/*
+ * When XPC HB determines that a partition has come up, it will create a new
+ * kthread and that kthread will call this function to attempt to set up the
+ * basic infrastructure used for Cross Partition Communication with the newly
+ * upped partition.
+ *
+ * The kthread that was created by XPC HB and which setup the XPC
+ * infrastructure will remain assigned to the partition becoming the channel
+ * manager for that partition until the partition is deactivating, at which
+ * time the kthread will teardown the XPC infrastructure and then exit.
+ */
static int
xpc_activating(void *__partid)
{
struct xpc_partition *part = &xpc_partitions[partid];
unsigned long irq_flags;
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
+ DBUG_ON(partid < 0 || partid >= xp_max_npartitions);
spin_lock_irqsave(&part->act_lock, irq_flags);
- if (part->act_state == XPC_P_DEACTIVATING) {
- part->act_state = XPC_P_INACTIVE;
+ if (part->act_state == XPC_P_AS_DEACTIVATING) {
+ part->act_state = XPC_P_AS_INACTIVE;
spin_unlock_irqrestore(&part->act_lock, irq_flags);
part->remote_rp_pa = 0;
return 0;
}
/* indicate the thread is activating */
- DBUG_ON(part->act_state != XPC_P_ACTIVATION_REQ);
- part->act_state = XPC_P_ACTIVATING;
+ DBUG_ON(part->act_state != XPC_P_AS_ACTIVATION_REQ);
+ part->act_state = XPC_P_AS_ACTIVATING;
XPC_SET_REASON(part, 0, 0);
spin_unlock_irqrestore(&part->act_lock, irq_flags);
- dev_dbg(xpc_part, "bringing partition %d up\n", partid);
+ dev_dbg(xpc_part, "activating partition %d\n", partid);
- /*
- * Register the remote partition's AMOs with SAL so it can handle
- * and cleanup errors within that address range should the remote
- * partition go down. We don't unregister this range because it is
- * difficult to tell when outstanding writes to the remote partition
- * are finished and thus when it is safe to unregister. This should
- * not result in wasted space in the SAL xp_addr_region table because
- * we should get the same page for remote_amos_page_pa after module
- * reloads and system reboots.
- */
- if (sn_register_xp_addr_region(part->remote_amos_page_pa,
- PAGE_SIZE, 1) < 0) {
- dev_warn(xpc_part, "xpc_partition_up(%d) failed to register "
- "xp_addr region\n", partid);
+ xpc_allow_hb(partid);
- spin_lock_irqsave(&part->act_lock, irq_flags);
- part->act_state = XPC_P_INACTIVE;
- XPC_SET_REASON(part, xpPhysAddrRegFailed, __LINE__);
- spin_unlock_irqrestore(&part->act_lock, irq_flags);
- part->remote_rp_pa = 0;
- return 0;
- }
+ if (xpc_setup_ch_structures(part) == xpSuccess) {
+ (void)xpc_part_ref(part); /* this will always succeed */
- xpc_allow_hb(partid, xpc_vars);
- xpc_IPI_send_activated(part);
+ if (xpc_make_first_contact(part) == xpSuccess) {
+ xpc_mark_partition_active(part);
+ xpc_channel_mgr(part);
+ /* won't return until partition is deactivating */
+ }
- /*
- * xpc_partition_up() holds this thread and marks this partition as
- * XPC_P_ACTIVE by calling xpc_hb_mark_active().
- */
- (void)xpc_partition_up(part);
+ xpc_part_deref(part);
+ xpc_teardown_ch_structures(part);
+ }
- xpc_disallow_hb(partid, xpc_vars);
+ xpc_disallow_hb(partid);
xpc_mark_partition_inactive(part);
if (part->reason == xpReactivating) {
/* interrupting ourselves results in activating partition */
- xpc_IPI_send_reactivate(part);
+ xpc_request_partition_reactivation(part);
}
return 0;
spin_lock_irqsave(&part->act_lock, irq_flags);
- DBUG_ON(part->act_state != XPC_P_INACTIVE);
+ DBUG_ON(part->act_state != XPC_P_AS_INACTIVE);
- part->act_state = XPC_P_ACTIVATION_REQ;
+ part->act_state = XPC_P_AS_ACTIVATION_REQ;
XPC_SET_REASON(part, xpCloneKThread, __LINE__);
spin_unlock_irqrestore(&part->act_lock, irq_flags);
partid);
if (IS_ERR(kthread)) {
spin_lock_irqsave(&part->act_lock, irq_flags);
- part->act_state = XPC_P_INACTIVE;
+ part->act_state = XPC_P_AS_INACTIVE;
XPC_SET_REASON(part, xpCloneKThreadFailed, __LINE__);
spin_unlock_irqrestore(&part->act_lock, irq_flags);
}
}
-/*
- * Handle the receipt of a SGI_XPC_NOTIFY IRQ by seeing whether the specified
- * partition actually sent it. Since SGI_XPC_NOTIFY IRQs may be shared by more
- * than one partition, we use an AMO_t structure per partition to indicate
- * whether a partition has sent an IPI or not. If it has, then wake up the
- * associated kthread to handle it.
- *
- * All SGI_XPC_NOTIFY IRQs received by XPC are the result of IPIs sent by XPC
- * running on other partitions.
- *
- * Noteworthy Arguments:
- *
- * irq - Interrupt ReQuest number. NOT USED.
- *
- * dev_id - partid of IPI's potential sender.
- */
-irqreturn_t
-xpc_notify_IRQ_handler(int irq, void *dev_id)
-{
- short partid = (short)(u64)dev_id;
- struct xpc_partition *part = &xpc_partitions[partid];
-
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
-
- if (xpc_part_ref(part)) {
- xpc_check_for_channel_activity(part);
-
- xpc_part_deref(part);
- }
- return IRQ_HANDLED;
-}
-
-/*
- * Check to see if xpc_notify_IRQ_handler() dropped any IPIs on the floor
- * because the write to their associated IPI amo completed after the IRQ/IPI
- * was received.
- */
-void
-xpc_dropped_IPI_check(struct xpc_partition *part)
-{
- if (xpc_part_ref(part)) {
- xpc_check_for_channel_activity(part);
-
- part->dropped_IPI_timer.expires = jiffies +
- XPC_P_DROPPED_IPI_WAIT;
- add_timer(&part->dropped_IPI_timer);
- xpc_part_deref(part);
- }
-}
-
void
xpc_activate_kthreads(struct xpc_channel *ch, int needed)
{
do {
/* deliver messages to their intended recipients */
- while (ch->w_local_GP.get < ch->w_remote_GP.put &&
+ while (xpc_n_of_deliverable_payloads(ch) > 0 &&
!(ch->flags & XPC_C_DISCONNECTING)) {
- xpc_deliver_msg(ch);
+ xpc_deliver_payload(ch);
}
if (atomic_inc_return(&ch->kthreads_idle) >
"wait_event_interruptible_exclusive()\n");
(void)wait_event_interruptible_exclusive(ch->idle_wq,
- (ch->w_local_GP.get < ch->w_remote_GP.put ||
+ (xpc_n_of_deliverable_payloads(ch) > 0 ||
(ch->flags & XPC_C_DISCONNECTING)));
atomic_dec(&ch->kthreads_idle);
* additional kthreads to help deliver them. We only
* need one less than total #of messages to deliver.
*/
- n_needed = ch->w_remote_GP.put - ch->w_local_GP.get - 1;
+ n_needed = xpc_n_of_deliverable_payloads(ch) - 1;
if (n_needed > 0 && !(ch->flags & XPC_C_DISCONNECTING))
xpc_activate_kthreads(ch, n_needed);
}
spin_unlock_irqrestore(&ch->lock, irq_flags);
- if (atomic_dec_return(&ch->kthreads_assigned) == 0) {
- if (atomic_dec_return(&part->nchannels_engaged) == 0) {
- xpc_mark_partition_disengaged(part);
- xpc_IPI_send_disengage(part);
- }
+ if (atomic_dec_return(&ch->kthreads_assigned) == 0 &&
+ atomic_dec_return(&part->nchannels_engaged) == 0) {
+ xpc_indicate_partition_disengaged(part);
}
xpc_msgqueue_deref(ch);
} else if (ch->flags & XPC_C_DISCONNECTING) {
break;
- } else if (atomic_inc_return(&ch->kthreads_assigned) == 1) {
- if (atomic_inc_return(&part->nchannels_engaged) == 1)
- xpc_mark_partition_engaged(part);
+ } else if (atomic_inc_return(&ch->kthreads_assigned) == 1 &&
+ atomic_inc_return(&part->nchannels_engaged) == 1) {
+ xpc_indicate_partition_engaged(part);
}
(void)xpc_part_ref(part);
xpc_msgqueue_ref(ch);
if (atomic_dec_return(&ch->kthreads_assigned) == 0 &&
atomic_dec_return(&part->nchannels_engaged) == 0) {
- xpc_mark_partition_disengaged(part);
- xpc_IPI_send_disengage(part);
+ xpc_indicate_partition_disengaged(part);
}
xpc_msgqueue_deref(ch);
xpc_part_deref(part);
int wakeup_channel_mgr;
/* now wait for all callouts to the caller's function to cease */
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
part = &xpc_partitions[partid];
if (!xpc_part_ref(part))
DBUG_ON(!(ch->flags & XPC_C_DISCONNECTED));
wakeup_channel_mgr = 0;
- if (ch->delayed_IPI_flags) {
- if (part->act_state != XPC_P_DEACTIVATING) {
- spin_lock(&part->IPI_lock);
- XPC_SET_IPI_FLAGS(part->local_IPI_amo,
- ch->number,
- ch->delayed_IPI_flags);
- spin_unlock(&part->IPI_lock);
+ if (ch->delayed_chctl_flags) {
+ if (part->act_state != XPC_P_AS_DEACTIVATING) {
+ spin_lock(&part->chctl_lock);
+ part->chctl.flags[ch->number] |=
+ ch->delayed_chctl_flags;
+ spin_unlock(&part->chctl_lock);
wakeup_channel_mgr = 1;
}
- ch->delayed_IPI_flags = 0;
+ ch->delayed_chctl_flags = 0;
}
ch->flags &= ~XPC_C_WDISCONNECT;
}
}
+static int
+xpc_setup_partitions(void)
+{
+ short partid;
+ struct xpc_partition *part;
+
+ xpc_partitions = kzalloc(sizeof(struct xpc_partition) *
+ xp_max_npartitions, GFP_KERNEL);
+ if (xpc_partitions == NULL) {
+ dev_err(xpc_part, "can't get memory for partition structure\n");
+ return -ENOMEM;
+ }
+
+ /*
+ * The first few fields of each entry of xpc_partitions[] need to
+ * be initialized now so that calls to xpc_connect() and
+ * xpc_disconnect() can be made prior to the activation of any remote
+ * partition. NOTE THAT NONE OF THE OTHER FIELDS BELONGING TO THESE
+ * ENTRIES ARE MEANINGFUL UNTIL AFTER AN ENTRY'S CORRESPONDING
+ * PARTITION HAS BEEN ACTIVATED.
+ */
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
+ part = &xpc_partitions[partid];
+
+ DBUG_ON((u64)part != L1_CACHE_ALIGN((u64)part));
+
+ part->activate_IRQ_rcvd = 0;
+ spin_lock_init(&part->act_lock);
+ part->act_state = XPC_P_AS_INACTIVE;
+ XPC_SET_REASON(part, 0, 0);
+
+ init_timer(&part->disengage_timer);
+ part->disengage_timer.function =
+ xpc_timeout_partition_disengage;
+ part->disengage_timer.data = (unsigned long)part;
+
+ part->setup_state = XPC_P_SS_UNSET;
+ init_waitqueue_head(&part->teardown_wq);
+ atomic_set(&part->references, 0);
+ }
+
+ return xpc_setup_partitions_sn();
+}
+
+static void
+xpc_teardown_partitions(void)
+{
+ kfree(xpc_partitions);
+}
+
static void
xpc_do_exit(enum xp_retval reason)
{
short partid;
int active_part_count, printed_waiting_msg = 0;
struct xpc_partition *part;
- unsigned long printmsg_time, disengage_request_timeout = 0;
+ unsigned long printmsg_time, disengage_timeout = 0;
/* a 'rmmod XPC' and a 'reboot' cannot both end up here together */
DBUG_ON(xpc_exiting == 1);
* the heartbeat checker thread in case it's sleeping.
*/
xpc_exiting = 1;
- wake_up_interruptible(&xpc_act_IRQ_wq);
-
- /* ignore all incoming interrupts */
- free_irq(SGI_XPC_ACTIVATE, NULL);
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
/* wait for the discovery thread to exit */
wait_for_completion(&xpc_discovery_exited);
/* wait for all partitions to become inactive */
- printmsg_time = jiffies + (XPC_DISENGAGE_PRINTMSG_INTERVAL * HZ);
- xpc_disengage_request_timedout = 0;
+ printmsg_time = jiffies + (XPC_DEACTIVATE_PRINTMSG_INTERVAL * HZ);
+ xpc_disengage_timedout = 0;
do {
active_part_count = 0;
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
part = &xpc_partitions[partid];
if (xpc_partition_disengaged(part) &&
- part->act_state == XPC_P_INACTIVE) {
+ part->act_state == XPC_P_AS_INACTIVE) {
continue;
}
XPC_DEACTIVATE_PARTITION(part, reason);
- if (part->disengage_request_timeout >
- disengage_request_timeout) {
- disengage_request_timeout =
- part->disengage_request_timeout;
- }
+ if (part->disengage_timeout > disengage_timeout)
+ disengage_timeout = part->disengage_timeout;
}
- if (xpc_partition_engaged(-1UL)) {
- if (time_after(jiffies, printmsg_time)) {
+ if (xpc_any_partition_engaged()) {
+ if (time_is_before_jiffies(printmsg_time)) {
dev_info(xpc_part, "waiting for remote "
- "partitions to disengage, timeout in "
- "%ld seconds\n",
- (disengage_request_timeout - jiffies)
- / HZ);
+ "partitions to deactivate, timeout in "
+ "%ld seconds\n", (disengage_timeout -
+ jiffies) / HZ);
printmsg_time = jiffies +
- (XPC_DISENGAGE_PRINTMSG_INTERVAL * HZ);
+ (XPC_DEACTIVATE_PRINTMSG_INTERVAL * HZ);
printed_waiting_msg = 1;
}
} else if (active_part_count > 0) {
if (printed_waiting_msg) {
dev_info(xpc_part, "waiting for local partition"
- " to disengage\n");
+ " to deactivate\n");
printed_waiting_msg = 0;
}
} else {
- if (!xpc_disengage_request_timedout) {
+ if (!xpc_disengage_timedout) {
dev_info(xpc_part, "all partitions have "
- "disengaged\n");
+ "deactivated\n");
}
break;
}
} while (1);
- DBUG_ON(xpc_partition_engaged(-1UL));
+ DBUG_ON(xpc_any_partition_engaged());
+ DBUG_ON(xpc_any_hbs_allowed() != 0);
- /* indicate to others that our reserved page is uninitialized */
- xpc_rsvd_page->vars_pa = 0;
-
- /* now it's time to eliminate our heartbeat */
- del_timer_sync(&xpc_hb_timer);
- DBUG_ON(xpc_vars->heartbeating_to_mask != 0);
+ xpc_teardown_rsvd_page();
if (reason == xpUnloading) {
- /* take ourselves off of the reboot_notifier_list */
- (void)unregister_reboot_notifier(&xpc_reboot_notifier);
-
- /* take ourselves off of the die_notifier list */
(void)unregister_die_notifier(&xpc_die_notifier);
+ (void)unregister_reboot_notifier(&xpc_reboot_notifier);
}
- /* close down protections for IPI operations */
- xpc_restrict_IPI_ops();
-
/* clear the interface to XPC's functions */
xpc_clear_interface();
if (xpc_sysctl)
unregister_sysctl_table(xpc_sysctl);
- kfree(xpc_remote_copy_buffer_base);
+ xpc_teardown_partitions();
+
+ if (is_shub())
+ xpc_exit_sn2();
+ else
+ xpc_exit_uv();
}
/*
}
/*
- * Notify other partitions to disengage from all references to our memory.
+ * Notify other partitions to deactivate from us by first disengaging from all
+ * references to our memory.
*/
static void
-xpc_die_disengage(void)
+xpc_die_deactivate(void)
{
struct xpc_partition *part;
short partid;
- unsigned long engaged;
- long time, printmsg_time, disengage_request_timeout;
+ int any_engaged;
+ long keep_waiting;
+ long wait_to_print;
/* keep xpc_hb_checker thread from doing anything (just in case) */
xpc_exiting = 1;
- xpc_vars->heartbeating_to_mask = 0; /* indicate we're deactivated */
+ xpc_disallow_all_hbs(); /*indicate we're deactivated */
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
+ for (partid = 0; partid < xp_max_npartitions; partid++) {
part = &xpc_partitions[partid];
- if (!XPC_SUPPORTS_DISENGAGE_REQUEST(part->
- remote_vars_version)) {
-
- /* just in case it was left set by an earlier XPC */
- xpc_clear_partition_engaged(1UL << partid);
- continue;
- }
-
- if (xpc_partition_engaged(1UL << partid) ||
- part->act_state != XPC_P_INACTIVE) {
- xpc_request_partition_disengage(part);
- xpc_mark_partition_disengaged(part);
- xpc_IPI_send_disengage(part);
+ if (xpc_partition_engaged(partid) ||
+ part->act_state != XPC_P_AS_INACTIVE) {
+ xpc_request_partition_deactivation(part);
+ xpc_indicate_partition_disengaged(part);
}
}
- time = rtc_time();
- printmsg_time = time +
- (XPC_DISENGAGE_PRINTMSG_INTERVAL * sn_rtc_cycles_per_second);
- disengage_request_timeout = time +
- (xpc_disengage_request_timelimit * sn_rtc_cycles_per_second);
-
- /* wait for all other partitions to disengage from us */
+ /*
+ * Though we requested that all other partitions deactivate from us,
+ * we only wait until they've all disengaged or we've reached the
+ * defined timelimit.
+ *
+ * Given that one iteration through the following while-loop takes
+ * approximately 200 microseconds, calculate the #of loops to take
+ * before bailing and the #of loops before printing a waiting message.
+ */
+ keep_waiting = xpc_disengage_timelimit * 1000 * 5;
+ wait_to_print = XPC_DEACTIVATE_PRINTMSG_INTERVAL * 1000 * 5;
while (1) {
- engaged = xpc_partition_engaged(-1UL);
- if (!engaged) {
- dev_info(xpc_part, "all partitions have disengaged\n");
+ any_engaged = xpc_any_partition_engaged();
+ if (!any_engaged) {
+ dev_info(xpc_part, "all partitions have deactivated\n");
break;
}
- time = rtc_time();
- if (time >= disengage_request_timeout) {
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
- if (engaged & (1UL << partid)) {
- dev_info(xpc_part, "disengage from "
+ if (!keep_waiting--) {
+ for (partid = 0; partid < xp_max_npartitions;
+ partid++) {
+ if (xpc_partition_engaged(partid)) {
+ dev_info(xpc_part, "deactivate from "
"remote partition %d timed "
"out\n", partid);
}
break;
}
- if (time >= printmsg_time) {
+ if (!wait_to_print--) {
dev_info(xpc_part, "waiting for remote partitions to "
- "disengage, timeout in %ld seconds\n",
- (disengage_request_timeout - time) /
- sn_rtc_cycles_per_second);
- printmsg_time = time +
- (XPC_DISENGAGE_PRINTMSG_INTERVAL *
- sn_rtc_cycles_per_second);
+ "deactivate, timeout in %ld seconds\n",
+ keep_waiting / (1000 * 5));
+ wait_to_print = XPC_DEACTIVATE_PRINTMSG_INTERVAL *
+ 1000 * 5;
}
+
+ udelay(200);
}
}
static int
xpc_system_die(struct notifier_block *nb, unsigned long event, void *unused)
{
+#ifdef CONFIG_IA64 /* !!! temporary kludge */
switch (event) {
case DIE_MACHINE_RESTART:
case DIE_MACHINE_HALT:
- xpc_die_disengage();
+ xpc_die_deactivate();
break;
case DIE_KDEBUG_ENTER:
/* fall through */
case DIE_MCA_MONARCH_ENTER:
case DIE_INIT_MONARCH_ENTER:
- xpc_vars->heartbeat++;
- xpc_vars->heartbeat_offline = 1;
+ xpc_offline_heartbeat();
break;
case DIE_KDEBUG_LEAVE:
/* fall through */
case DIE_MCA_MONARCH_LEAVE:
case DIE_INIT_MONARCH_LEAVE:
- xpc_vars->heartbeat++;
- xpc_vars->heartbeat_offline = 0;
+ xpc_online_heartbeat();
break;
}
+#else
+ xpc_die_deactivate();
+#endif
return NOTIFY_DONE;
}
xpc_init(void)
{
int ret;
- short partid;
- struct xpc_partition *part;
struct task_struct *kthread;
- size_t buf_size;
-
- if (!ia64_platform_is("sn2"))
- return -ENODEV;
-
- buf_size = max(XPC_RP_VARS_SIZE,
- XPC_RP_HEADER_SIZE + XP_NASID_MASK_BYTES);
- xpc_remote_copy_buffer = xpc_kmalloc_cacheline_aligned(buf_size,
- GFP_KERNEL,
- &xpc_remote_copy_buffer_base);
- if (xpc_remote_copy_buffer == NULL)
- return -ENOMEM;
snprintf(xpc_part->bus_id, BUS_ID_SIZE, "part");
snprintf(xpc_chan->bus_id, BUS_ID_SIZE, "chan");
- xpc_sysctl = register_sysctl_table(xpc_sys_dir);
-
- /*
- * The first few fields of each entry of xpc_partitions[] need to
- * be initialized now so that calls to xpc_connect() and
- * xpc_disconnect() can be made prior to the activation of any remote
- * partition. NOTE THAT NONE OF THE OTHER FIELDS BELONGING TO THESE
- * ENTRIES ARE MEANINGFUL UNTIL AFTER AN ENTRY'S CORRESPONDING
- * PARTITION HAS BEEN ACTIVATED.
- */
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
- part = &xpc_partitions[partid];
-
- DBUG_ON((u64)part != L1_CACHE_ALIGN((u64)part));
-
- part->act_IRQ_rcvd = 0;
- spin_lock_init(&part->act_lock);
- part->act_state = XPC_P_INACTIVE;
- XPC_SET_REASON(part, 0, 0);
+ if (is_shub()) {
+ /*
+ * The ia64-sn2 architecture supports at most 64 partitions.
+ * And the inability to unregister remote amos restricts us
+ * further to only support exactly 64 partitions on this
+ * architecture, no less.
+ */
+ if (xp_max_npartitions != 64) {
+ dev_err(xpc_part, "max #of partitions not set to 64\n");
+ ret = -EINVAL;
+ } else {
+ ret = xpc_init_sn2();
+ }
- init_timer(&part->disengage_request_timer);
- part->disengage_request_timer.function =
- xpc_timeout_partition_disengage_request;
- part->disengage_request_timer.data = (unsigned long)part;
+ } else if (is_uv()) {
+ ret = xpc_init_uv();
- part->setup_state = XPC_P_UNSET;
- init_waitqueue_head(&part->teardown_wq);
- atomic_set(&part->references, 0);
+ } else {
+ ret = -ENODEV;
}
- /*
- * Open up protections for IPI operations (and AMO operations on
- * Shub 1.1 systems).
- */
- xpc_allow_IPI_ops();
-
- /*
- * Interrupts being processed will increment this atomic variable and
- * awaken the heartbeat thread which will process the interrupts.
- */
- atomic_set(&xpc_act_IRQ_rcvd, 0);
+ if (ret != 0)
+ return ret;
- /*
- * This is safe to do before the xpc_hb_checker thread has started
- * because the handler releases a wait queue. If an interrupt is
- * received before the thread is waiting, it will not go to sleep,
- * but rather immediately process the interrupt.
- */
- ret = request_irq(SGI_XPC_ACTIVATE, xpc_act_IRQ_handler, 0,
- "xpc hb", NULL);
+ ret = xpc_setup_partitions();
if (ret != 0) {
- dev_err(xpc_part, "can't register ACTIVATE IRQ handler, "
- "errno=%d\n", -ret);
-
- xpc_restrict_IPI_ops();
-
- if (xpc_sysctl)
- unregister_sysctl_table(xpc_sysctl);
-
- kfree(xpc_remote_copy_buffer_base);
- return -EBUSY;
+ dev_err(xpc_part, "can't get memory for partition structure\n");
+ goto out_1;
}
+ xpc_sysctl = register_sysctl_table(xpc_sys_dir);
+
/*
* Fill the partition reserved page with the information needed by
* other partitions to discover we are alive and establish initial
* communications.
*/
- xpc_rsvd_page = xpc_rsvd_page_init();
- if (xpc_rsvd_page == NULL) {
- dev_err(xpc_part, "could not setup our reserved page\n");
-
- free_irq(SGI_XPC_ACTIVATE, NULL);
- xpc_restrict_IPI_ops();
-
- if (xpc_sysctl)
- unregister_sysctl_table(xpc_sysctl);
-
- kfree(xpc_remote_copy_buffer_base);
- return -EBUSY;
+ ret = xpc_setup_rsvd_page();
+ if (ret != 0) {
+ dev_err(xpc_part, "can't setup our reserved page\n");
+ goto out_2;
}
/* add ourselves to the reboot_notifier_list */
if (ret != 0)
dev_warn(xpc_part, "can't register die notifier\n");
- init_timer(&xpc_hb_timer);
- xpc_hb_timer.function = xpc_hb_beater;
-
/*
* The real work-horse behind xpc. This processes incoming
* interrupts and monitors remote heartbeats.
kthread = kthread_run(xpc_hb_checker, NULL, XPC_HB_CHECK_THREAD_NAME);
if (IS_ERR(kthread)) {
dev_err(xpc_part, "failed while forking hb check thread\n");
-
- /* indicate to others that our reserved page is uninitialized */
- xpc_rsvd_page->vars_pa = 0;
-
- /* take ourselves off of the reboot_notifier_list */
- (void)unregister_reboot_notifier(&xpc_reboot_notifier);
-
- /* take ourselves off of the die_notifier list */
- (void)unregister_die_notifier(&xpc_die_notifier);
-
- del_timer_sync(&xpc_hb_timer);
- free_irq(SGI_XPC_ACTIVATE, NULL);
- xpc_restrict_IPI_ops();
-
- if (xpc_sysctl)
- unregister_sysctl_table(xpc_sysctl);
-
- kfree(xpc_remote_copy_buffer_base);
- return -EBUSY;
+ ret = -EBUSY;
+ goto out_3;
}
/*
/* set the interface to point at XPC's functions */
xpc_set_interface(xpc_initiate_connect, xpc_initiate_disconnect,
- xpc_initiate_allocate, xpc_initiate_send,
- xpc_initiate_send_notify, xpc_initiate_received,
- xpc_initiate_partid_to_nasids);
+ xpc_initiate_send, xpc_initiate_send_notify,
+ xpc_initiate_received, xpc_initiate_partid_to_nasids);
return 0;
+
+ /* initialization was not successful */
+out_3:
+ xpc_teardown_rsvd_page();
+
+ (void)unregister_die_notifier(&xpc_die_notifier);
+ (void)unregister_reboot_notifier(&xpc_reboot_notifier);
+out_2:
+ if (xpc_sysctl)
+ unregister_sysctl_table(xpc_sysctl);
+
+ xpc_teardown_partitions();
+out_1:
+ if (is_shub())
+ xpc_exit_sn2();
+ else
+ xpc_exit_uv();
+ return ret;
}
module_init(xpc_init);
MODULE_PARM_DESC(xpc_hb_check_interval, "Number of seconds between "
"heartbeat checks.");
-module_param(xpc_disengage_request_timelimit, int, 0);
-MODULE_PARM_DESC(xpc_disengage_request_timelimit, "Number of seconds to wait "
- "for disengage request to complete.");
+module_param(xpc_disengage_timelimit, int, 0);
+MODULE_PARM_DESC(xpc_disengage_timelimit, "Number of seconds to wait "
+ "for disengage to complete.");
module_param(xpc_kdebug_ignore, int, 0);
MODULE_PARM_DESC(xpc_kdebug_ignore, "Should lack of heartbeat be ignored by "
*
*/
-#include <linux/kernel.h>
-#include <linux/sysctl.h>
-#include <linux/cache.h>
-#include <linux/mmzone.h>
-#include <linux/nodemask.h>
-#include <asm/uncached.h>
-#include <asm/sn/bte.h>
-#include <asm/sn/intr.h>
-#include <asm/sn/sn_sal.h>
-#include <asm/sn/nodepda.h>
-#include <asm/sn/addrs.h>
+#include <linux/device.h>
+#include <linux/hardirq.h>
#include "xpc.h"
/* XPC is exiting flag */
int xpc_exiting;
-/* SH_IPI_ACCESS shub register value on startup */
-static u64 xpc_sh1_IPI_access;
-static u64 xpc_sh2_IPI_access0;
-static u64 xpc_sh2_IPI_access1;
-static u64 xpc_sh2_IPI_access2;
-static u64 xpc_sh2_IPI_access3;
-
-/* original protection values for each node */
-u64 xpc_prot_vec[MAX_NUMNODES];
-
/* this partition's reserved page pointers */
struct xpc_rsvd_page *xpc_rsvd_page;
-static u64 *xpc_part_nasids;
-static u64 *xpc_mach_nasids;
-struct xpc_vars *xpc_vars;
-struct xpc_vars_part *xpc_vars_part;
+static unsigned long *xpc_part_nasids;
+unsigned long *xpc_mach_nasids;
-static int xp_nasid_mask_bytes; /* actual size in bytes of nasid mask */
-static int xp_nasid_mask_words; /* actual size in words of nasid mask */
-
-/*
- * For performance reasons, each entry of xpc_partitions[] is cacheline
- * aligned. And xpc_partitions[] is padded with an additional entry at the
- * end so that the last legitimate entry doesn't share its cacheline with
- * another variable.
- */
-struct xpc_partition xpc_partitions[XP_MAX_PARTITIONS + 1];
+static int xpc_nasid_mask_nbytes; /* #of bytes in nasid mask */
+int xpc_nasid_mask_nlongs; /* #of longs in nasid mask */
-/*
- * Generic buffer used to store a local copy of portions of a remote
- * partition's reserved page (either its header and part_nasids mask,
- * or its vars).
- */
-char *xpc_remote_copy_buffer;
-void *xpc_remote_copy_buffer_base;
+struct xpc_partition *xpc_partitions;
/*
* Guarantee that the kmalloc'd memory is cacheline aligned.
* Given a nasid, get the physical address of the partition's reserved page
* for that nasid. This function returns 0 on any error.
*/
-static u64
+static unsigned long
xpc_get_rsvd_page_pa(int nasid)
{
- bte_result_t bte_res;
- s64 status;
+ enum xp_retval ret;
u64 cookie = 0;
- u64 rp_pa = nasid; /* seed with nasid */
- u64 len = 0;
- u64 buf = buf;
- u64 buf_len = 0;
+ unsigned long rp_pa = nasid; /* seed with nasid */
+ size_t len = 0;
+ size_t buf_len = 0;
+ void *buf = buf;
void *buf_base = NULL;
while (1) {
- status = sn_partition_reserved_page_pa(buf, &cookie, &rp_pa,
- &len);
+ /* !!! rp_pa will need to be _gpa on UV.
+ * ??? So do we save it into the architecture specific parts
+ * ??? of the xpc_partition structure? Do we rename this
+ * ??? function or have two versions? Rename rp_pa for UV to
+ * ??? rp_gpa?
+ */
+ ret = xpc_get_partition_rsvd_page_pa(buf, &cookie, &rp_pa,
+ &len);
- dev_dbg(xpc_part, "SAL returned with status=%li, cookie="
- "0x%016lx, address=0x%016lx, len=0x%016lx\n",
- status, cookie, rp_pa, len);
+ dev_dbg(xpc_part, "SAL returned with ret=%d, cookie=0x%016lx, "
+ "address=0x%016lx, len=0x%016lx\n", ret,
+ (unsigned long)cookie, rp_pa, len);
- if (status != SALRET_MORE_PASSES)
+ if (ret != xpNeedMoreInfo)
break;
+ /* !!! L1_CACHE_ALIGN() is only a sn2-bte_copy requirement */
if (L1_CACHE_ALIGN(len) > buf_len) {
kfree(buf_base);
buf_len = L1_CACHE_ALIGN(len);
- buf = (u64)xpc_kmalloc_cacheline_aligned(buf_len,
- GFP_KERNEL,
- &buf_base);
+ buf = xpc_kmalloc_cacheline_aligned(buf_len, GFP_KERNEL,
+ &buf_base);
if (buf_base == NULL) {
dev_err(xpc_part, "unable to kmalloc "
"len=0x%016lx\n", buf_len);
- status = SALRET_ERROR;
+ ret = xpNoMemory;
break;
}
}
- bte_res = xp_bte_copy(rp_pa, buf, buf_len,
- (BTE_NOTIFY | BTE_WACQUIRE), NULL);
- if (bte_res != BTE_SUCCESS) {
- dev_dbg(xpc_part, "xp_bte_copy failed %i\n", bte_res);
- status = SALRET_ERROR;
+ ret = xp_remote_memcpy(xp_pa(buf), rp_pa, buf_len);
+ if (ret != xpSuccess) {
+ dev_dbg(xpc_part, "xp_remote_memcpy failed %d\n", ret);
break;
}
}
kfree(buf_base);
- if (status != SALRET_OK)
+ if (ret != xpSuccess)
rp_pa = 0;
dev_dbg(xpc_part, "reserved page at phys address 0x%016lx\n", rp_pa);
* other partitions to discover we are alive and establish initial
* communications.
*/
-struct xpc_rsvd_page *
-xpc_rsvd_page_init(void)
+int
+xpc_setup_rsvd_page(void)
{
+ int ret;
struct xpc_rsvd_page *rp;
- AMO_t *amos_page;
- u64 rp_pa, nasid_array = 0;
- int i, ret;
+ unsigned long rp_pa;
+ unsigned long new_ts_jiffies;
/* get the local reserved page's address */
preempt_disable();
- rp_pa = xpc_get_rsvd_page_pa(cpuid_to_nasid(smp_processor_id()));
+ rp_pa = xpc_get_rsvd_page_pa(xp_cpu_to_nasid(smp_processor_id()));
preempt_enable();
if (rp_pa == 0) {
dev_err(xpc_part, "SAL failed to locate the reserved page\n");
- return NULL;
+ return -ESRCH;
}
rp = (struct xpc_rsvd_page *)__va(rp_pa);
- if (rp->partid != sn_partition_id) {
- dev_err(xpc_part, "the reserved page's partid of %d should be "
- "%d\n", rp->partid, sn_partition_id);
- return NULL;
+ if (rp->SAL_version < 3) {
+ /* SAL_versions < 3 had a SAL_partid defined as a u8 */
+ rp->SAL_partid &= 0xff;
+ }
+ BUG_ON(rp->SAL_partid != xp_partition_id);
+
+ if (rp->SAL_partid < 0 || rp->SAL_partid >= xp_max_npartitions) {
+ dev_err(xpc_part, "the reserved page's partid of %d is outside "
+ "supported range (< 0 || >= %d)\n", rp->SAL_partid,
+ xp_max_npartitions);
+ return -EINVAL;
}
rp->version = XPC_RP_VERSION;
+ rp->max_npartitions = xp_max_npartitions;
/* establish the actual sizes of the nasid masks */
if (rp->SAL_version == 1) {
/* SAL_version 1 didn't set the nasids_size field */
- rp->nasids_size = 128;
+ rp->SAL_nasids_size = 128;
}
- xp_nasid_mask_bytes = rp->nasids_size;
- xp_nasid_mask_words = xp_nasid_mask_bytes / 8;
+ xpc_nasid_mask_nbytes = rp->SAL_nasids_size;
+ xpc_nasid_mask_nlongs = BITS_TO_LONGS(rp->SAL_nasids_size *
+ BITS_PER_BYTE);
/* setup the pointers to the various items in the reserved page */
xpc_part_nasids = XPC_RP_PART_NASIDS(rp);
xpc_mach_nasids = XPC_RP_MACH_NASIDS(rp);
- xpc_vars = XPC_RP_VARS(rp);
- xpc_vars_part = XPC_RP_VARS_PART(rp);
-
- /*
- * Before clearing xpc_vars, see if a page of AMOs had been previously
- * allocated. If not we'll need to allocate one and set permissions
- * so that cross-partition AMOs are allowed.
- *
- * The allocated AMO page needs MCA reporting to remain disabled after
- * XPC has unloaded. To make this work, we keep a copy of the pointer
- * to this page (i.e., amos_page) in the struct xpc_vars structure,
- * which is pointed to by the reserved page, and re-use that saved copy
- * on subsequent loads of XPC. This AMO page is never freed, and its
- * memory protections are never restricted.
- */
- amos_page = xpc_vars->amos_page;
- if (amos_page == NULL) {
- amos_page = (AMO_t *)TO_AMO(uncached_alloc_page(0, 1));
- if (amos_page == NULL) {
- dev_err(xpc_part, "can't allocate page of AMOs\n");
- return NULL;
- }
-
- /*
- * Open up AMO-R/W to cpu. This is done for Shub 1.1 systems
- * when xpc_allow_IPI_ops() is called via xpc_hb_init().
- */
- if (!enable_shub_wars_1_1()) {
- ret = sn_change_memprotect(ia64_tpa((u64)amos_page),
- PAGE_SIZE,
- SN_MEMPROT_ACCESS_CLASS_1,
- &nasid_array);
- if (ret != 0) {
- dev_err(xpc_part, "can't change memory "
- "protections\n");
- uncached_free_page(__IA64_UNCACHED_OFFSET |
- TO_PHYS((u64)amos_page), 1);
- return NULL;
- }
- }
- } else if (!IS_AMO_ADDRESS((u64)amos_page)) {
- /*
- * EFI's XPBOOT can also set amos_page in the reserved page,
- * but it happens to leave it as an uncached physical address
- * and we need it to be an uncached virtual, so we'll have to
- * convert it.
- */
- if (!IS_AMO_PHYS_ADDRESS((u64)amos_page)) {
- dev_err(xpc_part, "previously used amos_page address "
- "is bad = 0x%p\n", (void *)amos_page);
- return NULL;
- }
- amos_page = (AMO_t *)TO_AMO((u64)amos_page);
- }
-
- /* clear xpc_vars */
- memset(xpc_vars, 0, sizeof(struct xpc_vars));
-
- xpc_vars->version = XPC_V_VERSION;
- xpc_vars->act_nasid = cpuid_to_nasid(0);
- xpc_vars->act_phys_cpuid = cpu_physical_id(0);
- xpc_vars->vars_part_pa = __pa(xpc_vars_part);
- xpc_vars->amos_page_pa = ia64_tpa((u64)amos_page);
- xpc_vars->amos_page = amos_page; /* save for next load of XPC */
-
- /* clear xpc_vars_part */
- memset((u64 *)xpc_vars_part, 0, sizeof(struct xpc_vars_part) *
- XP_MAX_PARTITIONS);
-
- /* initialize the activate IRQ related AMO variables */
- for (i = 0; i < xp_nasid_mask_words; i++)
- (void)xpc_IPI_init(XPC_ACTIVATE_IRQ_AMOS + i);
-
- /* initialize the engaged remote partitions related AMO variables */
- (void)xpc_IPI_init(XPC_ENGAGED_PARTITIONS_AMO);
- (void)xpc_IPI_init(XPC_DISENGAGE_REQUEST_AMO);
- /* timestamp of when reserved page was setup by XPC */
- rp->stamp = CURRENT_TIME;
+ ret = xpc_setup_rsvd_page_sn(rp);
+ if (ret != 0)
+ return ret;
/*
+ * Set timestamp of when reserved page was setup by XPC.
* This signifies to the remote partition that our reserved
* page is initialized.
*/
- rp->vars_pa = __pa(xpc_vars);
+ new_ts_jiffies = jiffies;
+ if (new_ts_jiffies == 0 || new_ts_jiffies == rp->ts_jiffies)
+ new_ts_jiffies++;
+ rp->ts_jiffies = new_ts_jiffies;
- return rp;
+ xpc_rsvd_page = rp;
+ return 0;
}
-/*
- * Change protections to allow IPI operations (and AMO operations on
- * Shub 1.1 systems).
- */
void
-xpc_allow_IPI_ops(void)
+xpc_teardown_rsvd_page(void)
{
- int node;
- int nasid;
-
- /* >>> Change SH_IPI_ACCESS code to use SAL call once it is available */
-
- if (is_shub2()) {
- xpc_sh2_IPI_access0 =
- (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS0));
- xpc_sh2_IPI_access1 =
- (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS1));
- xpc_sh2_IPI_access2 =
- (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS2));
- xpc_sh2_IPI_access3 =
- (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS3));
-
- for_each_online_node(node) {
- nasid = cnodeid_to_nasid(node);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS0),
- -1UL);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS1),
- -1UL);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS2),
- -1UL);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS3),
- -1UL);
- }
-
- } else {
- xpc_sh1_IPI_access =
- (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH1_IPI_ACCESS));
-
- for_each_online_node(node) {
- nasid = cnodeid_to_nasid(node);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH1_IPI_ACCESS),
- -1UL);
-
- /*
- * Since the BIST collides with memory operations on
- * SHUB 1.1 sn_change_memprotect() cannot be used.
- */
- if (enable_shub_wars_1_1()) {
- /* open up everything */
- xpc_prot_vec[node] = (u64)HUB_L((u64 *)
- GLOBAL_MMR_ADDR
- (nasid,
- SH1_MD_DQLP_MMR_DIR_PRIVEC0));
- HUB_S((u64 *)
- GLOBAL_MMR_ADDR(nasid,
- SH1_MD_DQLP_MMR_DIR_PRIVEC0),
- -1UL);
- HUB_S((u64 *)
- GLOBAL_MMR_ADDR(nasid,
- SH1_MD_DQRP_MMR_DIR_PRIVEC0),
- -1UL);
- }
- }
- }
-}
-
-/*
- * Restrict protections to disallow IPI operations (and AMO operations on
- * Shub 1.1 systems).
- */
-void
-xpc_restrict_IPI_ops(void)
-{
- int node;
- int nasid;
-
- /* >>> Change SH_IPI_ACCESS code to use SAL call once it is available */
-
- if (is_shub2()) {
-
- for_each_online_node(node) {
- nasid = cnodeid_to_nasid(node);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS0),
- xpc_sh2_IPI_access0);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS1),
- xpc_sh2_IPI_access1);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS2),
- xpc_sh2_IPI_access2);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS3),
- xpc_sh2_IPI_access3);
- }
-
- } else {
-
- for_each_online_node(node) {
- nasid = cnodeid_to_nasid(node);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH1_IPI_ACCESS),
- xpc_sh1_IPI_access);
-
- if (enable_shub_wars_1_1()) {
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid,
- SH1_MD_DQLP_MMR_DIR_PRIVEC0),
- xpc_prot_vec[node]);
- HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid,
- SH1_MD_DQRP_MMR_DIR_PRIVEC0),
- xpc_prot_vec[node]);
- }
- }
- }
-}
-
-/*
- * At periodic intervals, scan through all active partitions and ensure
- * their heartbeat is still active. If not, the partition is deactivated.
- */
-void
-xpc_check_remote_hb(void)
-{
- struct xpc_vars *remote_vars;
- struct xpc_partition *part;
- short partid;
- bte_result_t bres;
-
- remote_vars = (struct xpc_vars *)xpc_remote_copy_buffer;
-
- for (partid = 1; partid < XP_MAX_PARTITIONS; partid++) {
-
- if (xpc_exiting)
- break;
-
- if (partid == sn_partition_id)
- continue;
-
- part = &xpc_partitions[partid];
-
- if (part->act_state == XPC_P_INACTIVE ||
- part->act_state == XPC_P_DEACTIVATING) {
- continue;
- }
-
- /* pull the remote_hb cache line */
- bres = xp_bte_copy(part->remote_vars_pa,
- (u64)remote_vars,
- XPC_RP_VARS_SIZE,
- (BTE_NOTIFY | BTE_WACQUIRE), NULL);
- if (bres != BTE_SUCCESS) {
- XPC_DEACTIVATE_PARTITION(part,
- xpc_map_bte_errors(bres));
- continue;
- }
-
- dev_dbg(xpc_part, "partid = %d, heartbeat = %ld, last_heartbeat"
- " = %ld, heartbeat_offline = %ld, HB_mask = 0x%lx\n",
- partid, remote_vars->heartbeat, part->last_heartbeat,
- remote_vars->heartbeat_offline,
- remote_vars->heartbeating_to_mask);
-
- if (((remote_vars->heartbeat == part->last_heartbeat) &&
- (remote_vars->heartbeat_offline == 0)) ||
- !xpc_hb_allowed(sn_partition_id, remote_vars)) {
-
- XPC_DEACTIVATE_PARTITION(part, xpNoHeartbeat);
- continue;
- }
-
- part->last_heartbeat = remote_vars->heartbeat;
- }
+ /* a zero timestamp indicates our rsvd page is not initialized */
+ xpc_rsvd_page->ts_jiffies = 0;
}
/*
* is large enough to contain a copy of their reserved page header and
* part_nasids mask.
*/
-static enum xp_retval
-xpc_get_remote_rp(int nasid, u64 *discovered_nasids,
- struct xpc_rsvd_page *remote_rp, u64 *remote_rp_pa)
+enum xp_retval
+xpc_get_remote_rp(int nasid, unsigned long *discovered_nasids,
+ struct xpc_rsvd_page *remote_rp, unsigned long *remote_rp_pa)
{
- int bres, i;
+ int l;
+ enum xp_retval ret;
/* get the reserved page's physical address */
return xpNoRsvdPageAddr;
/* pull over the reserved page header and part_nasids mask */
- bres = xp_bte_copy(*remote_rp_pa, (u64)remote_rp,
- XPC_RP_HEADER_SIZE + xp_nasid_mask_bytes,
- (BTE_NOTIFY | BTE_WACQUIRE), NULL);
- if (bres != BTE_SUCCESS)
- return xpc_map_bte_errors(bres);
+ ret = xp_remote_memcpy(xp_pa(remote_rp), *remote_rp_pa,
+ XPC_RP_HEADER_SIZE + xpc_nasid_mask_nbytes);
+ if (ret != xpSuccess)
+ return ret;
if (discovered_nasids != NULL) {
- u64 *remote_part_nasids = XPC_RP_PART_NASIDS(remote_rp);
-
- for (i = 0; i < xp_nasid_mask_words; i++)
- discovered_nasids[i] |= remote_part_nasids[i];
- }
-
- /* check that the partid is for another partition */
+ unsigned long *remote_part_nasids =
+ XPC_RP_PART_NASIDS(remote_rp);
- if (remote_rp->partid < 1 ||
- remote_rp->partid > (XP_MAX_PARTITIONS - 1)) {
- return xpInvalidPartid;
+ for (l = 0; l < xpc_nasid_mask_nlongs; l++)
+ discovered_nasids[l] |= remote_part_nasids[l];
}
- if (remote_rp->partid == sn_partition_id)
- return xpLocalPartid;
+ /* zero timestamp indicates the reserved page has not been setup */
+ if (remote_rp->ts_jiffies == 0)
+ return xpRsvdPageNotSet;
if (XPC_VERSION_MAJOR(remote_rp->version) !=
XPC_VERSION_MAJOR(XPC_RP_VERSION)) {
return xpBadVersion;
}
- return xpSuccess;
-}
-
-/*
- * Get a copy of the remote partition's XPC variables from the reserved page.
- *
- * remote_vars points to a buffer that is cacheline aligned for BTE copies and
- * assumed to be of size XPC_RP_VARS_SIZE.
- */
-static enum xp_retval
-xpc_get_remote_vars(u64 remote_vars_pa, struct xpc_vars *remote_vars)
-{
- int bres;
-
- if (remote_vars_pa == 0)
- return xpVarsNotSet;
-
- /* pull over the cross partition variables */
- bres = xp_bte_copy(remote_vars_pa, (u64)remote_vars, XPC_RP_VARS_SIZE,
- (BTE_NOTIFY | BTE_WACQUIRE), NULL);
- if (bres != BTE_SUCCESS)
- return xpc_map_bte_errors(bres);
-
- if (XPC_VERSION_MAJOR(remote_vars->version) !=
- XPC_VERSION_MAJOR(XPC_V_VERSION)) {
- return xpBadVersion;
- }
-
- return xpSuccess;
-}
-
-/*
- * Update the remote partition's info.
- */
-static void
-xpc_update_partition_info(struct xpc_partition *part, u8 remote_rp_version,
- struct timespec *remote_rp_stamp, u64 remote_rp_pa,
- u64 remote_vars_pa, struct xpc_vars *remote_vars)
-{
- part->remote_rp_version = remote_rp_version;
- dev_dbg(xpc_part, " remote_rp_version = 0x%016x\n",
- part->remote_rp_version);
-
- part->remote_rp_stamp = *remote_rp_stamp;
- dev_dbg(xpc_part, " remote_rp_stamp (tv_sec = 0x%lx tv_nsec = 0x%lx\n",
- part->remote_rp_stamp.tv_sec, part->remote_rp_stamp.tv_nsec);
-
- part->remote_rp_pa = remote_rp_pa;
- dev_dbg(xpc_part, " remote_rp_pa = 0x%016lx\n", part->remote_rp_pa);
-
- part->remote_vars_pa = remote_vars_pa;
- dev_dbg(xpc_part, " remote_vars_pa = 0x%016lx\n",
- part->remote_vars_pa);
-
- part->last_heartbeat = remote_vars->heartbeat;
- dev_dbg(xpc_part, " last_heartbeat = 0x%016lx\n",
- part->last_heartbeat);
-
- part->remote_vars_part_pa = remote_vars->vars_part_pa;
- dev_dbg(xpc_part, " remote_vars_part_pa = 0x%016lx\n",
- part->remote_vars_part_pa);
-
- part->remote_act_nasid = remote_vars->act_nasid;
- dev_dbg(xpc_part, " remote_act_nasid = 0x%x\n",
- part->remote_act_nasid);
-
- part->remote_act_phys_cpuid = remote_vars->act_phys_cpuid;
- dev_dbg(xpc_part, " remote_act_phys_cpuid = 0x%x\n",
- part->remote_act_phys_cpuid);
-
- part->remote_amos_page_pa = remote_vars->amos_page_pa;
- dev_dbg(xpc_part, " remote_amos_page_pa = 0x%lx\n",
- part->remote_amos_page_pa);
-
- part->remote_vars_version = remote_vars->version;
- dev_dbg(xpc_part, " remote_vars_version = 0x%x\n",
- part->remote_vars_version);
-}
-
-/*
- * Prior code has determined the nasid which generated an IPI. Inspect
- * that nasid to determine if its partition needs to be activated or
- * deactivated.
- *
- * A partition is consider "awaiting activation" if our partition
- * flags indicate it is not active and it has a heartbeat. A
- * partition is considered "awaiting deactivation" if our partition
- * flags indicate it is active but it has no heartbeat or it is not
- * sending its heartbeat to us.
- *
- * To determine the heartbeat, the remote nasid must have a properly
- * initialized reserved page.
- */
-static void
-xpc_identify_act_IRQ_req(int nasid)
-{
- struct xpc_rsvd_page *remote_rp;
- struct xpc_vars *remote_vars;
- u64 remote_rp_pa;
- u64 remote_vars_pa;
- int remote_rp_version;
- int reactivate = 0;
- int stamp_diff;
- struct timespec remote_rp_stamp = { 0, 0 };
- short partid;
- struct xpc_partition *part;
- enum xp_retval ret;
-
- /* pull over the reserved page structure */
-
- remote_rp = (struct xpc_rsvd_page *)xpc_remote_copy_buffer;
-
- ret = xpc_get_remote_rp(nasid, NULL, remote_rp, &remote_rp_pa);
- if (ret != xpSuccess) {
- dev_warn(xpc_part, "unable to get reserved page from nasid %d, "
- "which sent interrupt, reason=%d\n", nasid, ret);
- return;
- }
-
- remote_vars_pa = remote_rp->vars_pa;
- remote_rp_version = remote_rp->version;
- if (XPC_SUPPORTS_RP_STAMP(remote_rp_version))
- remote_rp_stamp = remote_rp->stamp;
-
- partid = remote_rp->partid;
- part = &xpc_partitions[partid];
-
- /* pull over the cross partition variables */
-
- remote_vars = (struct xpc_vars *)xpc_remote_copy_buffer;
-
- ret = xpc_get_remote_vars(remote_vars_pa, remote_vars);
- if (ret != xpSuccess) {
-
- dev_warn(xpc_part, "unable to get XPC variables from nasid %d, "
- "which sent interrupt, reason=%d\n", nasid, ret);
-
- XPC_DEACTIVATE_PARTITION(part, ret);
- return;
- }
-
- part->act_IRQ_rcvd++;
-
- dev_dbg(xpc_part, "partid for nasid %d is %d; IRQs = %d; HB = "
- "%ld:0x%lx\n", (int)nasid, (int)partid, part->act_IRQ_rcvd,
- remote_vars->heartbeat, remote_vars->heartbeating_to_mask);
-
- if (xpc_partition_disengaged(part) &&
- part->act_state == XPC_P_INACTIVE) {
-
- xpc_update_partition_info(part, remote_rp_version,
- &remote_rp_stamp, remote_rp_pa,
- remote_vars_pa, remote_vars);
-
- if (XPC_SUPPORTS_DISENGAGE_REQUEST(part->remote_vars_version)) {
- if (xpc_partition_disengage_requested(1UL << partid)) {
- /*
- * Other side is waiting on us to disengage,
- * even though we already have.
- */
- return;
- }
- } else {
- /* other side doesn't support disengage requests */
- xpc_clear_partition_disengage_request(1UL << partid);
- }
-
- xpc_activate_partition(part);
- return;
- }
-
- DBUG_ON(part->remote_rp_version == 0);
- DBUG_ON(part->remote_vars_version == 0);
-
- if (!XPC_SUPPORTS_RP_STAMP(part->remote_rp_version)) {
- DBUG_ON(XPC_SUPPORTS_DISENGAGE_REQUEST(part->
- remote_vars_version));
-
- if (!XPC_SUPPORTS_RP_STAMP(remote_rp_version)) {
- DBUG_ON(XPC_SUPPORTS_DISENGAGE_REQUEST(remote_vars->
- version));
- /* see if the other side rebooted */
- if (part->remote_amos_page_pa ==
- remote_vars->amos_page_pa &&
- xpc_hb_allowed(sn_partition_id, remote_vars)) {
- /* doesn't look that way, so ignore the IPI */
- return;
- }
- }
-
- /*
- * Other side rebooted and previous XPC didn't support the
- * disengage request, so we don't need to do anything special.
- */
-
- xpc_update_partition_info(part, remote_rp_version,
- &remote_rp_stamp, remote_rp_pa,
- remote_vars_pa, remote_vars);
- part->reactivate_nasid = nasid;
- XPC_DEACTIVATE_PARTITION(part, xpReactivating);
- return;
- }
-
- DBUG_ON(!XPC_SUPPORTS_DISENGAGE_REQUEST(part->remote_vars_version));
-
- if (!XPC_SUPPORTS_RP_STAMP(remote_rp_version)) {
- DBUG_ON(!XPC_SUPPORTS_DISENGAGE_REQUEST(remote_vars->version));
-
- /*
- * Other side rebooted and previous XPC did support the
- * disengage request, but the new one doesn't.
- */
-
- xpc_clear_partition_engaged(1UL << partid);
- xpc_clear_partition_disengage_request(1UL << partid);
-
- xpc_update_partition_info(part, remote_rp_version,
- &remote_rp_stamp, remote_rp_pa,
- remote_vars_pa, remote_vars);
- reactivate = 1;
-
- } else {
- DBUG_ON(!XPC_SUPPORTS_DISENGAGE_REQUEST(remote_vars->version));
-
- stamp_diff = xpc_compare_stamps(&part->remote_rp_stamp,
- &remote_rp_stamp);
- if (stamp_diff != 0) {
- DBUG_ON(stamp_diff >= 0);
-
- /*
- * Other side rebooted and the previous XPC did support
- * the disengage request, as does the new one.
- */
-
- DBUG_ON(xpc_partition_engaged(1UL << partid));
- DBUG_ON(xpc_partition_disengage_requested(1UL <<
- partid));
-
- xpc_update_partition_info(part, remote_rp_version,
- &remote_rp_stamp,
- remote_rp_pa, remote_vars_pa,
- remote_vars);
- reactivate = 1;
- }
- }
-
- if (part->disengage_request_timeout > 0 &&
- !xpc_partition_disengaged(part)) {
- /* still waiting on other side to disengage from us */
- return;
- }
-
- if (reactivate) {
- part->reactivate_nasid = nasid;
- XPC_DEACTIVATE_PARTITION(part, xpReactivating);
-
- } else if (XPC_SUPPORTS_DISENGAGE_REQUEST(part->remote_vars_version) &&
- xpc_partition_disengage_requested(1UL << partid)) {
- XPC_DEACTIVATE_PARTITION(part, xpOtherGoingDown);
+ /* check that both remote and local partids are valid for each side */
+ if (remote_rp->SAL_partid < 0 ||
+ remote_rp->SAL_partid >= xp_max_npartitions ||
+ remote_rp->max_npartitions <= xp_partition_id) {
+ return xpInvalidPartid;
}
-}
-/*
- * Loop through the activation AMO variables and process any bits
- * which are set. Each bit indicates a nasid sending a partition
- * activation or deactivation request.
- *
- * Return #of IRQs detected.
- */
-int
-xpc_identify_act_IRQ_sender(void)
-{
- int word, bit;
- u64 nasid_mask;
- u64 nasid; /* remote nasid */
- int n_IRQs_detected = 0;
- AMO_t *act_amos;
-
- act_amos = xpc_vars->amos_page + XPC_ACTIVATE_IRQ_AMOS;
-
- /* scan through act AMO variable looking for non-zero entries */
- for (word = 0; word < xp_nasid_mask_words; word++) {
-
- if (xpc_exiting)
- break;
-
- nasid_mask = xpc_IPI_receive(&act_amos[word]);
- if (nasid_mask == 0) {
- /* no IRQs from nasids in this variable */
- continue;
- }
-
- dev_dbg(xpc_part, "AMO[%d] gave back 0x%lx\n", word,
- nasid_mask);
-
- /*
- * If this nasid has been added to the machine since
- * our partition was reset, this will retain the
- * remote nasid in our reserved pages machine mask.
- * This is used in the event of module reload.
- */
- xpc_mach_nasids[word] |= nasid_mask;
-
- /* locate the nasid(s) which sent interrupts */
+ if (remote_rp->SAL_partid == xp_partition_id)
+ return xpLocalPartid;
- for (bit = 0; bit < (8 * sizeof(u64)); bit++) {
- if (nasid_mask & (1UL << bit)) {
- n_IRQs_detected++;
- nasid = XPC_NASID_FROM_W_B(word, bit);
- dev_dbg(xpc_part, "interrupt from nasid %ld\n",
- nasid);
- xpc_identify_act_IRQ_req(nasid);
- }
- }
- }
- return n_IRQs_detected;
+ return xpSuccess;
}
/*
- * See if the other side has responded to a partition disengage request
- * from us.
+ * See if the other side has responded to a partition deactivate request
+ * from us. Though we requested the remote partition to deactivate with regard
+ * to us, we really only need to wait for the other side to disengage from us.
*/
int
xpc_partition_disengaged(struct xpc_partition *part)
short partid = XPC_PARTID(part);
int disengaged;
- disengaged = (xpc_partition_engaged(1UL << partid) == 0);
- if (part->disengage_request_timeout) {
+ disengaged = !xpc_partition_engaged(partid);
+ if (part->disengage_timeout) {
if (!disengaged) {
- if (time_before(jiffies,
- part->disengage_request_timeout)) {
+ if (time_is_after_jiffies(part->disengage_timeout)) {
/* timelimit hasn't been reached yet */
return 0;
}
/*
- * Other side hasn't responded to our disengage
+ * Other side hasn't responded to our deactivate
* request in a timely fashion, so assume it's dead.
*/
- dev_info(xpc_part, "disengage from remote partition %d "
- "timed out\n", partid);
- xpc_disengage_request_timedout = 1;
- xpc_clear_partition_engaged(1UL << partid);
+ dev_info(xpc_part, "deactivate request to remote "
+ "partition %d timed out\n", partid);
+ xpc_disengage_timedout = 1;
+ xpc_assume_partition_disengaged(partid);
disengaged = 1;
}
- part->disengage_request_timeout = 0;
+ part->disengage_timeout = 0;
/* cancel the timer function, provided it's not us */
- if (!in_interrupt()) {
- del_singleshot_timer_sync(&part->
- disengage_request_timer);
- }
+ if (!in_interrupt())
+ del_singleshot_timer_sync(&part->disengage_timer);
- DBUG_ON(part->act_state != XPC_P_DEACTIVATING &&
- part->act_state != XPC_P_INACTIVE);
- if (part->act_state != XPC_P_INACTIVE)
+ DBUG_ON(part->act_state != XPC_P_AS_DEACTIVATING &&
+ part->act_state != XPC_P_AS_INACTIVE);
+ if (part->act_state != XPC_P_AS_INACTIVE)
xpc_wakeup_channel_mgr(part);
- if (XPC_SUPPORTS_DISENGAGE_REQUEST(part->remote_vars_version))
- xpc_cancel_partition_disengage_request(part);
+ xpc_cancel_partition_deactivation_request(part);
}
return disengaged;
}
dev_dbg(xpc_part, "setting partition %d to ACTIVE\n", XPC_PARTID(part));
spin_lock_irqsave(&part->act_lock, irq_flags);
- if (part->act_state == XPC_P_ACTIVATING) {
- part->act_state = XPC_P_ACTIVE;
+ if (part->act_state == XPC_P_AS_ACTIVATING) {
+ part->act_state = XPC_P_AS_ACTIVE;
ret = xpSuccess;
} else {
DBUG_ON(part->reason == xpSuccess);
}
/*
- * Notify XPC that the partition is down.
+ * Start the process of deactivating the specified partition.
*/
void
xpc_deactivate_partition(const int line, struct xpc_partition *part,
spin_lock_irqsave(&part->act_lock, irq_flags);
- if (part->act_state == XPC_P_INACTIVE) {
+ if (part->act_state == XPC_P_AS_INACTIVE) {
XPC_SET_REASON(part, reason, line);
spin_unlock_irqrestore(&part->act_lock, irq_flags);
if (reason == xpReactivating) {
/* we interrupt ourselves to reactivate partition */
- xpc_IPI_send_reactivate(part);
+ xpc_request_partition_reactivation(part);
}
return;
}
- if (part->act_state == XPC_P_DEACTIVATING) {
+ if (part->act_state == XPC_P_AS_DEACTIVATING) {
if ((part->reason == xpUnloading && reason != xpUnloading) ||
reason == xpReactivating) {
XPC_SET_REASON(part, reason, line);
return;
}
- part->act_state = XPC_P_DEACTIVATING;
+ part->act_state = XPC_P_AS_DEACTIVATING;
XPC_SET_REASON(part, reason, line);
spin_unlock_irqrestore(&part->act_lock, irq_flags);
- if (XPC_SUPPORTS_DISENGAGE_REQUEST(part->remote_vars_version)) {
- xpc_request_partition_disengage(part);
- xpc_IPI_send_disengage(part);
+ /* ask remote partition to deactivate with regard to us */
+ xpc_request_partition_deactivation(part);
- /* set a timelimit on the disengage request */
- part->disengage_request_timeout = jiffies +
- (xpc_disengage_request_timelimit * HZ);
- part->disengage_request_timer.expires =
- part->disengage_request_timeout;
- add_timer(&part->disengage_request_timer);
- }
+ /* set a timelimit on the disengage phase of the deactivation request */
+ part->disengage_timeout = jiffies + (xpc_disengage_timelimit * HZ);
+ part->disengage_timer.expires = part->disengage_timeout;
+ add_timer(&part->disengage_timer);
dev_dbg(xpc_part, "bringing partition %d down, reason = %d\n",
XPC_PARTID(part), reason);
XPC_PARTID(part));
spin_lock_irqsave(&part->act_lock, irq_flags);
- part->act_state = XPC_P_INACTIVE;
+ part->act_state = XPC_P_AS_INACTIVE;
spin_unlock_irqrestore(&part->act_lock, irq_flags);
part->remote_rp_pa = 0;
}
{
void *remote_rp_base;
struct xpc_rsvd_page *remote_rp;
- struct xpc_vars *remote_vars;
- u64 remote_rp_pa;
- u64 remote_vars_pa;
+ unsigned long remote_rp_pa;
int region;
int region_size;
int max_regions;
int nasid;
struct xpc_rsvd_page *rp;
- short partid;
- struct xpc_partition *part;
- u64 *discovered_nasids;
+ unsigned long *discovered_nasids;
enum xp_retval ret;
remote_rp = xpc_kmalloc_cacheline_aligned(XPC_RP_HEADER_SIZE +
- xp_nasid_mask_bytes,
+ xpc_nasid_mask_nbytes,
GFP_KERNEL, &remote_rp_base);
if (remote_rp == NULL)
return;
- remote_vars = (struct xpc_vars *)remote_rp;
-
- discovered_nasids = kzalloc(sizeof(u64) * xp_nasid_mask_words,
+ discovered_nasids = kzalloc(sizeof(long) * xpc_nasid_mask_nlongs,
GFP_KERNEL);
if (discovered_nasids == NULL) {
kfree(remote_rp_base);
* protection is in regards to memory, IOI and IPI.
*/
max_regions = 64;
- region_size = sn_region_size;
+ region_size = xp_region_size;
switch (region_size) {
case 128:
dev_dbg(xpc_part, "checking nasid %d\n", nasid);
- if (XPC_NASID_IN_ARRAY(nasid, xpc_part_nasids)) {
+ if (test_bit(nasid / 2, xpc_part_nasids)) {
dev_dbg(xpc_part, "PROM indicates Nasid %d is "
"part of the local partition; skipping "
"region\n", nasid);
break;
}
- if (!(XPC_NASID_IN_ARRAY(nasid, xpc_mach_nasids))) {
+ if (!(test_bit(nasid / 2, xpc_mach_nasids))) {
dev_dbg(xpc_part, "PROM indicates Nasid %d was "
"not on Numa-Link network at reset\n",
nasid);
continue;
}
- if (XPC_NASID_IN_ARRAY(nasid, discovered_nasids)) {
+ if (test_bit(nasid / 2, discovered_nasids)) {
dev_dbg(xpc_part, "Nasid %d is part of a "
"partition which was previously "
"discovered\n", nasid);
continue;
}
- /* pull over the reserved page structure */
+ /* pull over the rsvd page header & part_nasids mask */
ret = xpc_get_remote_rp(nasid, discovered_nasids,
remote_rp, &remote_rp_pa);
continue;
}
- remote_vars_pa = remote_rp->vars_pa;
-
- partid = remote_rp->partid;
- part = &xpc_partitions[partid];
-
- /* pull over the cross partition variables */
-
- ret = xpc_get_remote_vars(remote_vars_pa, remote_vars);
- if (ret != xpSuccess) {
- dev_dbg(xpc_part, "unable to get XPC variables "
- "from nasid %d, reason=%d\n", nasid,
- ret);
-
- XPC_DEACTIVATE_PARTITION(part, ret);
- continue;
- }
-
- if (part->act_state != XPC_P_INACTIVE) {
- dev_dbg(xpc_part, "partition %d on nasid %d is "
- "already activating\n", partid, nasid);
- break;
- }
-
- /*
- * Register the remote partition's AMOs with SAL so it
- * can handle and cleanup errors within that address
- * range should the remote partition go down. We don't
- * unregister this range because it is difficult to
- * tell when outstanding writes to the remote partition
- * are finished and thus when it is thus safe to
- * unregister. This should not result in wasted space
- * in the SAL xp_addr_region table because we should
- * get the same page for remote_act_amos_pa after
- * module reloads and system reboots.
- */
- if (sn_register_xp_addr_region
- (remote_vars->amos_page_pa, PAGE_SIZE, 1) < 0) {
- dev_dbg(xpc_part,
- "partition %d failed to "
- "register xp_addr region 0x%016lx\n",
- partid, remote_vars->amos_page_pa);
-
- XPC_SET_REASON(part, xpPhysAddrRegFailed,
- __LINE__);
- break;
- }
-
- /*
- * The remote nasid is valid and available.
- * Send an interrupt to that nasid to notify
- * it that we are ready to begin activation.
- */
- dev_dbg(xpc_part, "sending an interrupt to AMO 0x%lx, "
- "nasid %d, phys_cpuid 0x%x\n",
- remote_vars->amos_page_pa,
- remote_vars->act_nasid,
- remote_vars->act_phys_cpuid);
-
- if (XPC_SUPPORTS_DISENGAGE_REQUEST(remote_vars->
- version)) {
- part->remote_amos_page_pa =
- remote_vars->amos_page_pa;
- xpc_mark_partition_disengaged(part);
- xpc_cancel_partition_disengage_request(part);
- }
- xpc_IPI_send_activate(remote_vars);
+ xpc_request_partition_activation(remote_rp,
+ remote_rp_pa, nasid);
}
}
xpc_initiate_partid_to_nasids(short partid, void *nasid_mask)
{
struct xpc_partition *part;
- u64 part_nasid_pa;
- int bte_res;
+ unsigned long part_nasid_pa;
part = &xpc_partitions[partid];
if (part->remote_rp_pa == 0)
return xpPartitionDown;
- memset(nasid_mask, 0, XP_NASID_MASK_BYTES);
-
- part_nasid_pa = (u64)XPC_RP_PART_NASIDS(part->remote_rp_pa);
+ memset(nasid_mask, 0, xpc_nasid_mask_nbytes);
- bte_res = xp_bte_copy(part_nasid_pa, (u64)nasid_mask,
- xp_nasid_mask_bytes, (BTE_NOTIFY | BTE_WACQUIRE),
- NULL);
+ part_nasid_pa = (unsigned long)XPC_RP_PART_NASIDS(part->remote_rp_pa);
- return xpc_map_bte_errors(bte_res);
+ return xp_remote_memcpy(xp_pa(nasid_mask), part_nasid_pa,
+ xpc_nasid_mask_nbytes);
}
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ */
+
+/*
+ * Cross Partition Communication (XPC) sn2-based functions.
+ *
+ * Architecture specific implementation of common functions.
+ *
+ */
+
+#include <linux/delay.h>
+#include <asm/uncached.h>
+#include <asm/sn/mspec.h>
+#include <asm/sn/sn_sal.h>
+#include "xpc.h"
+
+/*
+ * Define the number of u64s required to represent all the C-brick nasids
+ * as a bitmap. The cross-partition kernel modules deal only with
+ * C-brick nasids, thus the need for bitmaps which don't account for
+ * odd-numbered (non C-brick) nasids.
+ */
+#define XPC_MAX_PHYSNODES_SN2 (MAX_NUMALINK_NODES / 2)
+#define XP_NASID_MASK_BYTES_SN2 ((XPC_MAX_PHYSNODES_SN2 + 7) / 8)
+#define XP_NASID_MASK_WORDS_SN2 ((XPC_MAX_PHYSNODES_SN2 + 63) / 64)
+
+/*
+ * Memory for XPC's amo variables is allocated by the MSPEC driver. These
+ * pages are located in the lowest granule. The lowest granule uses 4k pages
+ * for cached references and an alternate TLB handler to never provide a
+ * cacheable mapping for the entire region. This will prevent speculative
+ * reading of cached copies of our lines from being issued which will cause
+ * a PI FSB Protocol error to be generated by the SHUB. For XPC, we need 64
+ * amo variables (based on XP_MAX_NPARTITIONS_SN2) to identify the senders of
+ * NOTIFY IRQs, 128 amo variables (based on XP_NASID_MASK_WORDS_SN2) to identify
+ * the senders of ACTIVATE IRQs, 1 amo variable to identify which remote
+ * partitions (i.e., XPCs) consider themselves currently engaged with the
+ * local XPC and 1 amo variable to request partition deactivation.
+ */
+#define XPC_NOTIFY_IRQ_AMOS_SN2 0
+#define XPC_ACTIVATE_IRQ_AMOS_SN2 (XPC_NOTIFY_IRQ_AMOS_SN2 + \
+ XP_MAX_NPARTITIONS_SN2)
+#define XPC_ENGAGED_PARTITIONS_AMO_SN2 (XPC_ACTIVATE_IRQ_AMOS_SN2 + \
+ XP_NASID_MASK_WORDS_SN2)
+#define XPC_DEACTIVATE_REQUEST_AMO_SN2 (XPC_ENGAGED_PARTITIONS_AMO_SN2 + 1)
+
+/*
+ * Buffer used to store a local copy of portions of a remote partition's
+ * reserved page (either its header and part_nasids mask, or its vars).
+ */
+static void *xpc_remote_copy_buffer_base_sn2;
+static char *xpc_remote_copy_buffer_sn2;
+
+static struct xpc_vars_sn2 *xpc_vars_sn2;
+static struct xpc_vars_part_sn2 *xpc_vars_part_sn2;
+
+static int
+xpc_setup_partitions_sn_sn2(void)
+{
+ /* nothing needs to be done */
+ return 0;
+}
+
+/* SH_IPI_ACCESS shub register value on startup */
+static u64 xpc_sh1_IPI_access_sn2;
+static u64 xpc_sh2_IPI_access0_sn2;
+static u64 xpc_sh2_IPI_access1_sn2;
+static u64 xpc_sh2_IPI_access2_sn2;
+static u64 xpc_sh2_IPI_access3_sn2;
+
+/*
+ * Change protections to allow IPI operations.
+ */
+static void
+xpc_allow_IPI_ops_sn2(void)
+{
+ int node;
+ int nasid;
+
+ /* !!! The following should get moved into SAL. */
+ if (is_shub2()) {
+ xpc_sh2_IPI_access0_sn2 =
+ (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS0));
+ xpc_sh2_IPI_access1_sn2 =
+ (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS1));
+ xpc_sh2_IPI_access2_sn2 =
+ (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS2));
+ xpc_sh2_IPI_access3_sn2 =
+ (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH2_IPI_ACCESS3));
+
+ for_each_online_node(node) {
+ nasid = cnodeid_to_nasid(node);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS0),
+ -1UL);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS1),
+ -1UL);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS2),
+ -1UL);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS3),
+ -1UL);
+ }
+ } else {
+ xpc_sh1_IPI_access_sn2 =
+ (u64)HUB_L((u64 *)LOCAL_MMR_ADDR(SH1_IPI_ACCESS));
+
+ for_each_online_node(node) {
+ nasid = cnodeid_to_nasid(node);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH1_IPI_ACCESS),
+ -1UL);
+ }
+ }
+}
+
+/*
+ * Restrict protections to disallow IPI operations.
+ */
+static void
+xpc_disallow_IPI_ops_sn2(void)
+{
+ int node;
+ int nasid;
+
+ /* !!! The following should get moved into SAL. */
+ if (is_shub2()) {
+ for_each_online_node(node) {
+ nasid = cnodeid_to_nasid(node);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS0),
+ xpc_sh2_IPI_access0_sn2);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS1),
+ xpc_sh2_IPI_access1_sn2);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS2),
+ xpc_sh2_IPI_access2_sn2);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH2_IPI_ACCESS3),
+ xpc_sh2_IPI_access3_sn2);
+ }
+ } else {
+ for_each_online_node(node) {
+ nasid = cnodeid_to_nasid(node);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid, SH1_IPI_ACCESS),
+ xpc_sh1_IPI_access_sn2);
+ }
+ }
+}
+
+/*
+ * The following set of functions are used for the sending and receiving of
+ * IRQs (also known as IPIs). There are two flavors of IRQs, one that is
+ * associated with partition activity (SGI_XPC_ACTIVATE) and the other that
+ * is associated with channel activity (SGI_XPC_NOTIFY).
+ */
+
+static u64
+xpc_receive_IRQ_amo_sn2(struct amo *amo)
+{
+ return FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_CLEAR);
+}
+
+static enum xp_retval
+xpc_send_IRQ_sn2(struct amo *amo, u64 flag, int nasid, int phys_cpuid,
+ int vector)
+{
+ int ret = 0;
+ unsigned long irq_flags;
+
+ local_irq_save(irq_flags);
+
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR, flag);
+ sn_send_IPI_phys(nasid, phys_cpuid, vector, 0);
+
+ /*
+ * We must always use the nofault function regardless of whether we
+ * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
+ * didn't, we'd never know that the other partition is down and would
+ * keep sending IRQs and amos to it until the heartbeat times out.
+ */
+ ret = xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->variable),
+ xp_nofault_PIOR_target));
+
+ local_irq_restore(irq_flags);
+
+ return (ret == 0) ? xpSuccess : xpPioReadError;
+}
+
+static struct amo *
+xpc_init_IRQ_amo_sn2(int index)
+{
+ struct amo *amo = xpc_vars_sn2->amos_page + index;
+
+ (void)xpc_receive_IRQ_amo_sn2(amo); /* clear amo variable */
+ return amo;
+}
+
+/*
+ * Functions associated with SGI_XPC_ACTIVATE IRQ.
+ */
+
+/*
+ * Notify the heartbeat check thread that an activate IRQ has been received.
+ */
+static irqreturn_t
+xpc_handle_activate_IRQ_sn2(int irq, void *dev_id)
+{
+ unsigned long irq_flags;
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ xpc_activate_IRQ_rcvd++;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
+ return IRQ_HANDLED;
+}
+
+/*
+ * Flag the appropriate amo variable and send an IRQ to the specified node.
+ */
+static void
+xpc_send_activate_IRQ_sn2(unsigned long amos_page_pa, int from_nasid,
+ int to_nasid, int to_phys_cpuid)
+{
+ struct amo *amos = (struct amo *)__va(amos_page_pa +
+ (XPC_ACTIVATE_IRQ_AMOS_SN2 *
+ sizeof(struct amo)));
+
+ (void)xpc_send_IRQ_sn2(&amos[BIT_WORD(from_nasid / 2)],
+ BIT_MASK(from_nasid / 2), to_nasid,
+ to_phys_cpuid, SGI_XPC_ACTIVATE);
+}
+
+static void
+xpc_send_local_activate_IRQ_sn2(int from_nasid)
+{
+ unsigned long irq_flags;
+ struct amo *amos = (struct amo *)__va(xpc_vars_sn2->amos_page_pa +
+ (XPC_ACTIVATE_IRQ_AMOS_SN2 *
+ sizeof(struct amo)));
+
+ /* fake the sending and receipt of an activate IRQ from remote nasid */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amos[BIT_WORD(from_nasid / 2)].variable),
+ FETCHOP_OR, BIT_MASK(from_nasid / 2));
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ xpc_activate_IRQ_rcvd++;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
+}
+
+/*
+ * Functions associated with SGI_XPC_NOTIFY IRQ.
+ */
+
+/*
+ * Check to see if any chctl flags were sent from the specified partition.
+ */
+static void
+xpc_check_for_sent_chctl_flags_sn2(struct xpc_partition *part)
+{
+ union xpc_channel_ctl_flags chctl;
+ unsigned long irq_flags;
+
+ chctl.all_flags = xpc_receive_IRQ_amo_sn2(part->sn.sn2.
+ local_chctl_amo_va);
+ if (chctl.all_flags == 0)
+ return;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.all_flags |= chctl.all_flags;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ dev_dbg(xpc_chan, "received notify IRQ from partid=%d, chctl.all_flags="
+ "0x%lx\n", XPC_PARTID(part), chctl.all_flags);
+
+ xpc_wakeup_channel_mgr(part);
+}
+
+/*
+ * Handle the receipt of a SGI_XPC_NOTIFY IRQ by seeing whether the specified
+ * partition actually sent it. Since SGI_XPC_NOTIFY IRQs may be shared by more
+ * than one partition, we use an amo structure per partition to indicate
+ * whether a partition has sent an IRQ or not. If it has, then wake up the
+ * associated kthread to handle it.
+ *
+ * All SGI_XPC_NOTIFY IRQs received by XPC are the result of IRQs sent by XPC
+ * running on other partitions.
+ *
+ * Noteworthy Arguments:
+ *
+ * irq - Interrupt ReQuest number. NOT USED.
+ *
+ * dev_id - partid of IRQ's potential sender.
+ */
+static irqreturn_t
+xpc_handle_notify_IRQ_sn2(int irq, void *dev_id)
+{
+ short partid = (short)(u64)dev_id;
+ struct xpc_partition *part = &xpc_partitions[partid];
+
+ DBUG_ON(partid < 0 || partid >= XP_MAX_NPARTITIONS_SN2);
+
+ if (xpc_part_ref(part)) {
+ xpc_check_for_sent_chctl_flags_sn2(part);
+
+ xpc_part_deref(part);
+ }
+ return IRQ_HANDLED;
+}
+
+/*
+ * Check to see if xpc_handle_notify_IRQ_sn2() dropped any IRQs on the floor
+ * because the write to their associated amo variable completed after the IRQ
+ * was received.
+ */
+static void
+xpc_check_for_dropped_notify_IRQ_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+
+ if (xpc_part_ref(part)) {
+ xpc_check_for_sent_chctl_flags_sn2(part);
+
+ part_sn2->dropped_notify_IRQ_timer.expires = jiffies +
+ XPC_DROPPED_NOTIFY_IRQ_WAIT_INTERVAL;
+ add_timer(&part_sn2->dropped_notify_IRQ_timer);
+ xpc_part_deref(part);
+ }
+}
+
+/*
+ * Send a notify IRQ to the remote partition that is associated with the
+ * specified channel.
+ */
+static void
+xpc_send_notify_IRQ_sn2(struct xpc_channel *ch, u8 chctl_flag,
+ char *chctl_flag_string, unsigned long *irq_flags)
+{
+ struct xpc_partition *part = &xpc_partitions[ch->partid];
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ union xpc_channel_ctl_flags chctl = { 0 };
+ enum xp_retval ret;
+
+ if (likely(part->act_state != XPC_P_AS_DEACTIVATING)) {
+ chctl.flags[ch->number] = chctl_flag;
+ ret = xpc_send_IRQ_sn2(part_sn2->remote_chctl_amo_va,
+ chctl.all_flags,
+ part_sn2->notify_IRQ_nasid,
+ part_sn2->notify_IRQ_phys_cpuid,
+ SGI_XPC_NOTIFY);
+ dev_dbg(xpc_chan, "%s sent to partid=%d, channel=%d, ret=%d\n",
+ chctl_flag_string, ch->partid, ch->number, ret);
+ if (unlikely(ret != xpSuccess)) {
+ if (irq_flags != NULL)
+ spin_unlock_irqrestore(&ch->lock, *irq_flags);
+ XPC_DEACTIVATE_PARTITION(part, ret);
+ if (irq_flags != NULL)
+ spin_lock_irqsave(&ch->lock, *irq_flags);
+ }
+ }
+}
+
+#define XPC_SEND_NOTIFY_IRQ_SN2(_ch, _ipi_f, _irq_f) \
+ xpc_send_notify_IRQ_sn2(_ch, _ipi_f, #_ipi_f, _irq_f)
+
+/*
+ * Make it look like the remote partition, which is associated with the
+ * specified channel, sent us a notify IRQ. This faked IRQ will be handled
+ * by xpc_check_for_dropped_notify_IRQ_sn2().
+ */
+static void
+xpc_send_local_notify_IRQ_sn2(struct xpc_channel *ch, u8 chctl_flag,
+ char *chctl_flag_string)
+{
+ struct xpc_partition *part = &xpc_partitions[ch->partid];
+ union xpc_channel_ctl_flags chctl = { 0 };
+
+ chctl.flags[ch->number] = chctl_flag;
+ FETCHOP_STORE_OP(TO_AMO((u64)&part->sn.sn2.local_chctl_amo_va->
+ variable), FETCHOP_OR, chctl.all_flags);
+ dev_dbg(xpc_chan, "%s sent local from partid=%d, channel=%d\n",
+ chctl_flag_string, ch->partid, ch->number);
+}
+
+#define XPC_SEND_LOCAL_NOTIFY_IRQ_SN2(_ch, _ipi_f) \
+ xpc_send_local_notify_IRQ_sn2(_ch, _ipi_f, #_ipi_f)
+
+static void
+xpc_send_chctl_closerequest_sn2(struct xpc_channel *ch,
+ unsigned long *irq_flags)
+{
+ struct xpc_openclose_args *args = ch->sn.sn2.local_openclose_args;
+
+ args->reason = ch->reason;
+ XPC_SEND_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_CLOSEREQUEST, irq_flags);
+}
+
+static void
+xpc_send_chctl_closereply_sn2(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ XPC_SEND_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_CLOSEREPLY, irq_flags);
+}
+
+static void
+xpc_send_chctl_openrequest_sn2(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_openclose_args *args = ch->sn.sn2.local_openclose_args;
+
+ args->entry_size = ch->entry_size;
+ args->local_nentries = ch->local_nentries;
+ XPC_SEND_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_OPENREQUEST, irq_flags);
+}
+
+static void
+xpc_send_chctl_openreply_sn2(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_openclose_args *args = ch->sn.sn2.local_openclose_args;
+
+ args->remote_nentries = ch->remote_nentries;
+ args->local_nentries = ch->local_nentries;
+ args->local_msgqueue_pa = xp_pa(ch->sn.sn2.local_msgqueue);
+ XPC_SEND_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_OPENREPLY, irq_flags);
+}
+
+static void
+xpc_send_chctl_msgrequest_sn2(struct xpc_channel *ch)
+{
+ XPC_SEND_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_MSGREQUEST, NULL);
+}
+
+static void
+xpc_send_chctl_local_msgrequest_sn2(struct xpc_channel *ch)
+{
+ XPC_SEND_LOCAL_NOTIFY_IRQ_SN2(ch, XPC_CHCTL_MSGREQUEST);
+}
+
+static void
+xpc_save_remote_msgqueue_pa_sn2(struct xpc_channel *ch,
+ unsigned long msgqueue_pa)
+{
+ ch->sn.sn2.remote_msgqueue_pa = msgqueue_pa;
+}
+
+/*
+ * This next set of functions are used to keep track of when a partition is
+ * potentially engaged in accessing memory belonging to another partition.
+ */
+
+static void
+xpc_indicate_partition_engaged_sn2(struct xpc_partition *part)
+{
+ unsigned long irq_flags;
+ struct amo *amo = (struct amo *)__va(part->sn.sn2.remote_amos_page_pa +
+ (XPC_ENGAGED_PARTITIONS_AMO_SN2 *
+ sizeof(struct amo)));
+
+ local_irq_save(irq_flags);
+
+ /* set bit corresponding to our partid in remote partition's amo */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR,
+ BIT(sn_partition_id));
+
+ /*
+ * We must always use the nofault function regardless of whether we
+ * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
+ * didn't, we'd never know that the other partition is down and would
+ * keep sending IRQs and amos to it until the heartbeat times out.
+ */
+ (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
+ variable),
+ xp_nofault_PIOR_target));
+
+ local_irq_restore(irq_flags);
+}
+
+static void
+xpc_indicate_partition_disengaged_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ unsigned long irq_flags;
+ struct amo *amo = (struct amo *)__va(part_sn2->remote_amos_page_pa +
+ (XPC_ENGAGED_PARTITIONS_AMO_SN2 *
+ sizeof(struct amo)));
+
+ local_irq_save(irq_flags);
+
+ /* clear bit corresponding to our partid in remote partition's amo */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
+ ~BIT(sn_partition_id));
+
+ /*
+ * We must always use the nofault function regardless of whether we
+ * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
+ * didn't, we'd never know that the other partition is down and would
+ * keep sending IRQs and amos to it until the heartbeat times out.
+ */
+ (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
+ variable),
+ xp_nofault_PIOR_target));
+
+ local_irq_restore(irq_flags);
+
+ /*
+ * Send activate IRQ to get other side to see that we've cleared our
+ * bit in their engaged partitions amo.
+ */
+ xpc_send_activate_IRQ_sn2(part_sn2->remote_amos_page_pa,
+ cnodeid_to_nasid(0),
+ part_sn2->activate_IRQ_nasid,
+ part_sn2->activate_IRQ_phys_cpuid);
+}
+
+static void
+xpc_assume_partition_disengaged_sn2(short partid)
+{
+ struct amo *amo = xpc_vars_sn2->amos_page +
+ XPC_ENGAGED_PARTITIONS_AMO_SN2;
+
+ /* clear bit(s) based on partid mask in our partition's amo */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
+ ~BIT(partid));
+}
+
+static int
+xpc_partition_engaged_sn2(short partid)
+{
+ struct amo *amo = xpc_vars_sn2->amos_page +
+ XPC_ENGAGED_PARTITIONS_AMO_SN2;
+
+ /* our partition's amo variable ANDed with partid mask */
+ return (FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_LOAD) &
+ BIT(partid)) != 0;
+}
+
+static int
+xpc_any_partition_engaged_sn2(void)
+{
+ struct amo *amo = xpc_vars_sn2->amos_page +
+ XPC_ENGAGED_PARTITIONS_AMO_SN2;
+
+ /* our partition's amo variable */
+ return FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_LOAD) != 0;
+}
+
+/* original protection values for each node */
+static u64 xpc_prot_vec_sn2[MAX_NUMNODES];
+
+/*
+ * Change protections to allow amo operations on non-Shub 1.1 systems.
+ */
+static enum xp_retval
+xpc_allow_amo_ops_sn2(struct amo *amos_page)
+{
+ u64 nasid_array = 0;
+ int ret;
+
+ /*
+ * On SHUB 1.1, we cannot call sn_change_memprotect() since the BIST
+ * collides with memory operations. On those systems we call
+ * xpc_allow_amo_ops_shub_wars_1_1_sn2() instead.
+ */
+ if (!enable_shub_wars_1_1()) {
+ ret = sn_change_memprotect(ia64_tpa((u64)amos_page), PAGE_SIZE,
+ SN_MEMPROT_ACCESS_CLASS_1,
+ &nasid_array);
+ if (ret != 0)
+ return xpSalError;
+ }
+ return xpSuccess;
+}
+
+/*
+ * Change protections to allow amo operations on Shub 1.1 systems.
+ */
+static void
+xpc_allow_amo_ops_shub_wars_1_1_sn2(void)
+{
+ int node;
+ int nasid;
+
+ if (!enable_shub_wars_1_1())
+ return;
+
+ for_each_online_node(node) {
+ nasid = cnodeid_to_nasid(node);
+ /* save current protection values */
+ xpc_prot_vec_sn2[node] =
+ (u64)HUB_L((u64 *)GLOBAL_MMR_ADDR(nasid,
+ SH1_MD_DQLP_MMR_DIR_PRIVEC0));
+ /* open up everything */
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid,
+ SH1_MD_DQLP_MMR_DIR_PRIVEC0),
+ -1UL);
+ HUB_S((u64 *)GLOBAL_MMR_ADDR(nasid,
+ SH1_MD_DQRP_MMR_DIR_PRIVEC0),
+ -1UL);
+ }
+}
+
+static enum xp_retval
+xpc_get_partition_rsvd_page_pa_sn2(void *buf, u64 *cookie, unsigned long *rp_pa,
+ size_t *len)
+{
+ s64 status;
+ enum xp_retval ret;
+
+ status = sn_partition_reserved_page_pa((u64)buf, cookie, rp_pa, len);
+ if (status == SALRET_OK)
+ ret = xpSuccess;
+ else if (status == SALRET_MORE_PASSES)
+ ret = xpNeedMoreInfo;
+ else
+ ret = xpSalError;
+
+ return ret;
+}
+
+
+static int
+xpc_setup_rsvd_page_sn_sn2(struct xpc_rsvd_page *rp)
+{
+ struct amo *amos_page;
+ int i;
+ int ret;
+
+ xpc_vars_sn2 = XPC_RP_VARS(rp);
+
+ rp->sn.vars_pa = xp_pa(xpc_vars_sn2);
+
+ /* vars_part array follows immediately after vars */
+ xpc_vars_part_sn2 = (struct xpc_vars_part_sn2 *)((u8 *)XPC_RP_VARS(rp) +
+ XPC_RP_VARS_SIZE);
+
+ /*
+ * Before clearing xpc_vars_sn2, see if a page of amos had been
+ * previously allocated. If not we'll need to allocate one and set
+ * permissions so that cross-partition amos are allowed.
+ *
+ * The allocated amo page needs MCA reporting to remain disabled after
+ * XPC has unloaded. To make this work, we keep a copy of the pointer
+ * to this page (i.e., amos_page) in the struct xpc_vars_sn2 structure,
+ * which is pointed to by the reserved page, and re-use that saved copy
+ * on subsequent loads of XPC. This amo page is never freed, and its
+ * memory protections are never restricted.
+ */
+ amos_page = xpc_vars_sn2->amos_page;
+ if (amos_page == NULL) {
+ amos_page = (struct amo *)TO_AMO(uncached_alloc_page(0, 1));
+ if (amos_page == NULL) {
+ dev_err(xpc_part, "can't allocate page of amos\n");
+ return -ENOMEM;
+ }
+
+ /*
+ * Open up amo-R/W to cpu. This is done on Shub 1.1 systems
+ * when xpc_allow_amo_ops_shub_wars_1_1_sn2() is called.
+ */
+ ret = xpc_allow_amo_ops_sn2(amos_page);
+ if (ret != xpSuccess) {
+ dev_err(xpc_part, "can't allow amo operations\n");
+ uncached_free_page(__IA64_UNCACHED_OFFSET |
+ TO_PHYS((u64)amos_page), 1);
+ return -EPERM;
+ }
+ }
+
+ /* clear xpc_vars_sn2 */
+ memset(xpc_vars_sn2, 0, sizeof(struct xpc_vars_sn2));
+
+ xpc_vars_sn2->version = XPC_V_VERSION;
+ xpc_vars_sn2->activate_IRQ_nasid = cpuid_to_nasid(0);
+ xpc_vars_sn2->activate_IRQ_phys_cpuid = cpu_physical_id(0);
+ xpc_vars_sn2->vars_part_pa = xp_pa(xpc_vars_part_sn2);
+ xpc_vars_sn2->amos_page_pa = ia64_tpa((u64)amos_page);
+ xpc_vars_sn2->amos_page = amos_page; /* save for next load of XPC */
+
+ /* clear xpc_vars_part_sn2 */
+ memset((u64 *)xpc_vars_part_sn2, 0, sizeof(struct xpc_vars_part_sn2) *
+ XP_MAX_NPARTITIONS_SN2);
+
+ /* initialize the activate IRQ related amo variables */
+ for (i = 0; i < xpc_nasid_mask_nlongs; i++)
+ (void)xpc_init_IRQ_amo_sn2(XPC_ACTIVATE_IRQ_AMOS_SN2 + i);
+
+ /* initialize the engaged remote partitions related amo variables */
+ (void)xpc_init_IRQ_amo_sn2(XPC_ENGAGED_PARTITIONS_AMO_SN2);
+ (void)xpc_init_IRQ_amo_sn2(XPC_DEACTIVATE_REQUEST_AMO_SN2);
+
+ return 0;
+}
+
+static void
+xpc_increment_heartbeat_sn2(void)
+{
+ xpc_vars_sn2->heartbeat++;
+}
+
+static void
+xpc_offline_heartbeat_sn2(void)
+{
+ xpc_increment_heartbeat_sn2();
+ xpc_vars_sn2->heartbeat_offline = 1;
+}
+
+static void
+xpc_online_heartbeat_sn2(void)
+{
+ xpc_increment_heartbeat_sn2();
+ xpc_vars_sn2->heartbeat_offline = 0;
+}
+
+static void
+xpc_heartbeat_init_sn2(void)
+{
+ DBUG_ON(xpc_vars_sn2 == NULL);
+
+ bitmap_zero(xpc_vars_sn2->heartbeating_to_mask, XP_MAX_NPARTITIONS_SN2);
+ xpc_heartbeating_to_mask = &xpc_vars_sn2->heartbeating_to_mask[0];
+ xpc_online_heartbeat_sn2();
+}
+
+static void
+xpc_heartbeat_exit_sn2(void)
+{
+ xpc_offline_heartbeat_sn2();
+}
+
+static enum xp_retval
+xpc_get_remote_heartbeat_sn2(struct xpc_partition *part)
+{
+ struct xpc_vars_sn2 *remote_vars;
+ enum xp_retval ret;
+
+ remote_vars = (struct xpc_vars_sn2 *)xpc_remote_copy_buffer_sn2;
+
+ /* pull the remote vars structure that contains the heartbeat */
+ ret = xp_remote_memcpy(xp_pa(remote_vars),
+ part->sn.sn2.remote_vars_pa,
+ XPC_RP_VARS_SIZE);
+ if (ret != xpSuccess)
+ return ret;
+
+ dev_dbg(xpc_part, "partid=%d, heartbeat=%ld, last_heartbeat=%ld, "
+ "heartbeat_offline=%ld, HB_mask[0]=0x%lx\n", XPC_PARTID(part),
+ remote_vars->heartbeat, part->last_heartbeat,
+ remote_vars->heartbeat_offline,
+ remote_vars->heartbeating_to_mask[0]);
+
+ if ((remote_vars->heartbeat == part->last_heartbeat &&
+ remote_vars->heartbeat_offline == 0) ||
+ !xpc_hb_allowed(sn_partition_id,
+ &remote_vars->heartbeating_to_mask)) {
+ ret = xpNoHeartbeat;
+ } else {
+ part->last_heartbeat = remote_vars->heartbeat;
+ }
+
+ return ret;
+}
+
+/*
+ * Get a copy of the remote partition's XPC variables from the reserved page.
+ *
+ * remote_vars points to a buffer that is cacheline aligned for BTE copies and
+ * assumed to be of size XPC_RP_VARS_SIZE.
+ */
+static enum xp_retval
+xpc_get_remote_vars_sn2(unsigned long remote_vars_pa,
+ struct xpc_vars_sn2 *remote_vars)
+{
+ enum xp_retval ret;
+
+ if (remote_vars_pa == 0)
+ return xpVarsNotSet;
+
+ /* pull over the cross partition variables */
+ ret = xp_remote_memcpy(xp_pa(remote_vars), remote_vars_pa,
+ XPC_RP_VARS_SIZE);
+ if (ret != xpSuccess)
+ return ret;
+
+ if (XPC_VERSION_MAJOR(remote_vars->version) !=
+ XPC_VERSION_MAJOR(XPC_V_VERSION)) {
+ return xpBadVersion;
+ }
+
+ return xpSuccess;
+}
+
+static void
+xpc_request_partition_activation_sn2(struct xpc_rsvd_page *remote_rp,
+ unsigned long remote_rp_pa, int nasid)
+{
+ xpc_send_local_activate_IRQ_sn2(nasid);
+}
+
+static void
+xpc_request_partition_reactivation_sn2(struct xpc_partition *part)
+{
+ xpc_send_local_activate_IRQ_sn2(part->sn.sn2.activate_IRQ_nasid);
+}
+
+static void
+xpc_request_partition_deactivation_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ unsigned long irq_flags;
+ struct amo *amo = (struct amo *)__va(part_sn2->remote_amos_page_pa +
+ (XPC_DEACTIVATE_REQUEST_AMO_SN2 *
+ sizeof(struct amo)));
+
+ local_irq_save(irq_flags);
+
+ /* set bit corresponding to our partid in remote partition's amo */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_OR,
+ BIT(sn_partition_id));
+
+ /*
+ * We must always use the nofault function regardless of whether we
+ * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
+ * didn't, we'd never know that the other partition is down and would
+ * keep sending IRQs and amos to it until the heartbeat times out.
+ */
+ (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
+ variable),
+ xp_nofault_PIOR_target));
+
+ local_irq_restore(irq_flags);
+
+ /*
+ * Send activate IRQ to get other side to see that we've set our
+ * bit in their deactivate request amo.
+ */
+ xpc_send_activate_IRQ_sn2(part_sn2->remote_amos_page_pa,
+ cnodeid_to_nasid(0),
+ part_sn2->activate_IRQ_nasid,
+ part_sn2->activate_IRQ_phys_cpuid);
+}
+
+static void
+xpc_cancel_partition_deactivation_request_sn2(struct xpc_partition *part)
+{
+ unsigned long irq_flags;
+ struct amo *amo = (struct amo *)__va(part->sn.sn2.remote_amos_page_pa +
+ (XPC_DEACTIVATE_REQUEST_AMO_SN2 *
+ sizeof(struct amo)));
+
+ local_irq_save(irq_flags);
+
+ /* clear bit corresponding to our partid in remote partition's amo */
+ FETCHOP_STORE_OP(TO_AMO((u64)&amo->variable), FETCHOP_AND,
+ ~BIT(sn_partition_id));
+
+ /*
+ * We must always use the nofault function regardless of whether we
+ * are on a Shub 1.1 system or a Shub 1.2 slice 0xc processor. If we
+ * didn't, we'd never know that the other partition is down and would
+ * keep sending IRQs and amos to it until the heartbeat times out.
+ */
+ (void)xp_nofault_PIOR((u64 *)GLOBAL_MMR_ADDR(NASID_GET(&amo->
+ variable),
+ xp_nofault_PIOR_target));
+
+ local_irq_restore(irq_flags);
+}
+
+static int
+xpc_partition_deactivation_requested_sn2(short partid)
+{
+ struct amo *amo = xpc_vars_sn2->amos_page +
+ XPC_DEACTIVATE_REQUEST_AMO_SN2;
+
+ /* our partition's amo variable ANDed with partid mask */
+ return (FETCHOP_LOAD_OP(TO_AMO((u64)&amo->variable), FETCHOP_LOAD) &
+ BIT(partid)) != 0;
+}
+
+/*
+ * Update the remote partition's info.
+ */
+static void
+xpc_update_partition_info_sn2(struct xpc_partition *part, u8 remote_rp_version,
+ unsigned long *remote_rp_ts_jiffies,
+ unsigned long remote_rp_pa,
+ unsigned long remote_vars_pa,
+ struct xpc_vars_sn2 *remote_vars)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+
+ part->remote_rp_version = remote_rp_version;
+ dev_dbg(xpc_part, " remote_rp_version = 0x%016x\n",
+ part->remote_rp_version);
+
+ part->remote_rp_ts_jiffies = *remote_rp_ts_jiffies;
+ dev_dbg(xpc_part, " remote_rp_ts_jiffies = 0x%016lx\n",
+ part->remote_rp_ts_jiffies);
+
+ part->remote_rp_pa = remote_rp_pa;
+ dev_dbg(xpc_part, " remote_rp_pa = 0x%016lx\n", part->remote_rp_pa);
+
+ part_sn2->remote_vars_pa = remote_vars_pa;
+ dev_dbg(xpc_part, " remote_vars_pa = 0x%016lx\n",
+ part_sn2->remote_vars_pa);
+
+ part->last_heartbeat = remote_vars->heartbeat;
+ dev_dbg(xpc_part, " last_heartbeat = 0x%016lx\n",
+ part->last_heartbeat);
+
+ part_sn2->remote_vars_part_pa = remote_vars->vars_part_pa;
+ dev_dbg(xpc_part, " remote_vars_part_pa = 0x%016lx\n",
+ part_sn2->remote_vars_part_pa);
+
+ part_sn2->activate_IRQ_nasid = remote_vars->activate_IRQ_nasid;
+ dev_dbg(xpc_part, " activate_IRQ_nasid = 0x%x\n",
+ part_sn2->activate_IRQ_nasid);
+
+ part_sn2->activate_IRQ_phys_cpuid =
+ remote_vars->activate_IRQ_phys_cpuid;
+ dev_dbg(xpc_part, " activate_IRQ_phys_cpuid = 0x%x\n",
+ part_sn2->activate_IRQ_phys_cpuid);
+
+ part_sn2->remote_amos_page_pa = remote_vars->amos_page_pa;
+ dev_dbg(xpc_part, " remote_amos_page_pa = 0x%lx\n",
+ part_sn2->remote_amos_page_pa);
+
+ part_sn2->remote_vars_version = remote_vars->version;
+ dev_dbg(xpc_part, " remote_vars_version = 0x%x\n",
+ part_sn2->remote_vars_version);
+}
+
+/*
+ * Prior code has determined the nasid which generated a activate IRQ.
+ * Inspect that nasid to determine if its partition needs to be activated
+ * or deactivated.
+ *
+ * A partition is considered "awaiting activation" if our partition
+ * flags indicate it is not active and it has a heartbeat. A
+ * partition is considered "awaiting deactivation" if our partition
+ * flags indicate it is active but it has no heartbeat or it is not
+ * sending its heartbeat to us.
+ *
+ * To determine the heartbeat, the remote nasid must have a properly
+ * initialized reserved page.
+ */
+static void
+xpc_identify_activate_IRQ_req_sn2(int nasid)
+{
+ struct xpc_rsvd_page *remote_rp;
+ struct xpc_vars_sn2 *remote_vars;
+ unsigned long remote_rp_pa;
+ unsigned long remote_vars_pa;
+ int remote_rp_version;
+ int reactivate = 0;
+ unsigned long remote_rp_ts_jiffies = 0;
+ short partid;
+ struct xpc_partition *part;
+ struct xpc_partition_sn2 *part_sn2;
+ enum xp_retval ret;
+
+ /* pull over the reserved page structure */
+
+ remote_rp = (struct xpc_rsvd_page *)xpc_remote_copy_buffer_sn2;
+
+ ret = xpc_get_remote_rp(nasid, NULL, remote_rp, &remote_rp_pa);
+ if (ret != xpSuccess) {
+ dev_warn(xpc_part, "unable to get reserved page from nasid %d, "
+ "which sent interrupt, reason=%d\n", nasid, ret);
+ return;
+ }
+
+ remote_vars_pa = remote_rp->sn.vars_pa;
+ remote_rp_version = remote_rp->version;
+ remote_rp_ts_jiffies = remote_rp->ts_jiffies;
+
+ partid = remote_rp->SAL_partid;
+ part = &xpc_partitions[partid];
+ part_sn2 = &part->sn.sn2;
+
+ /* pull over the cross partition variables */
+
+ remote_vars = (struct xpc_vars_sn2 *)xpc_remote_copy_buffer_sn2;
+
+ ret = xpc_get_remote_vars_sn2(remote_vars_pa, remote_vars);
+ if (ret != xpSuccess) {
+ dev_warn(xpc_part, "unable to get XPC variables from nasid %d, "
+ "which sent interrupt, reason=%d\n", nasid, ret);
+
+ XPC_DEACTIVATE_PARTITION(part, ret);
+ return;
+ }
+
+ part->activate_IRQ_rcvd++;
+
+ dev_dbg(xpc_part, "partid for nasid %d is %d; IRQs = %d; HB = "
+ "%ld:0x%lx\n", (int)nasid, (int)partid, part->activate_IRQ_rcvd,
+ remote_vars->heartbeat, remote_vars->heartbeating_to_mask[0]);
+
+ if (xpc_partition_disengaged(part) &&
+ part->act_state == XPC_P_AS_INACTIVE) {
+
+ xpc_update_partition_info_sn2(part, remote_rp_version,
+ &remote_rp_ts_jiffies,
+ remote_rp_pa, remote_vars_pa,
+ remote_vars);
+
+ if (xpc_partition_deactivation_requested_sn2(partid)) {
+ /*
+ * Other side is waiting on us to deactivate even though
+ * we already have.
+ */
+ return;
+ }
+
+ xpc_activate_partition(part);
+ return;
+ }
+
+ DBUG_ON(part->remote_rp_version == 0);
+ DBUG_ON(part_sn2->remote_vars_version == 0);
+
+ if (remote_rp_ts_jiffies != part->remote_rp_ts_jiffies) {
+
+ /* the other side rebooted */
+
+ DBUG_ON(xpc_partition_engaged_sn2(partid));
+ DBUG_ON(xpc_partition_deactivation_requested_sn2(partid));
+
+ xpc_update_partition_info_sn2(part, remote_rp_version,
+ &remote_rp_ts_jiffies,
+ remote_rp_pa, remote_vars_pa,
+ remote_vars);
+ reactivate = 1;
+ }
+
+ if (part->disengage_timeout > 0 && !xpc_partition_disengaged(part)) {
+ /* still waiting on other side to disengage from us */
+ return;
+ }
+
+ if (reactivate)
+ XPC_DEACTIVATE_PARTITION(part, xpReactivating);
+ else if (xpc_partition_deactivation_requested_sn2(partid))
+ XPC_DEACTIVATE_PARTITION(part, xpOtherGoingDown);
+}
+
+/*
+ * Loop through the activation amo variables and process any bits
+ * which are set. Each bit indicates a nasid sending a partition
+ * activation or deactivation request.
+ *
+ * Return #of IRQs detected.
+ */
+int
+xpc_identify_activate_IRQ_sender_sn2(void)
+{
+ int l;
+ int b;
+ unsigned long nasid_mask_long;
+ u64 nasid; /* remote nasid */
+ int n_IRQs_detected = 0;
+ struct amo *act_amos;
+
+ act_amos = xpc_vars_sn2->amos_page + XPC_ACTIVATE_IRQ_AMOS_SN2;
+
+ /* scan through activate amo variables looking for non-zero entries */
+ for (l = 0; l < xpc_nasid_mask_nlongs; l++) {
+
+ if (xpc_exiting)
+ break;
+
+ nasid_mask_long = xpc_receive_IRQ_amo_sn2(&act_amos[l]);
+
+ b = find_first_bit(&nasid_mask_long, BITS_PER_LONG);
+ if (b >= BITS_PER_LONG) {
+ /* no IRQs from nasids in this amo variable */
+ continue;
+ }
+
+ dev_dbg(xpc_part, "amo[%d] gave back 0x%lx\n", l,
+ nasid_mask_long);
+
+ /*
+ * If this nasid has been added to the machine since
+ * our partition was reset, this will retain the
+ * remote nasid in our reserved pages machine mask.
+ * This is used in the event of module reload.
+ */
+ xpc_mach_nasids[l] |= nasid_mask_long;
+
+ /* locate the nasid(s) which sent interrupts */
+
+ do {
+ n_IRQs_detected++;
+ nasid = (l * BITS_PER_LONG + b) * 2;
+ dev_dbg(xpc_part, "interrupt from nasid %ld\n", nasid);
+ xpc_identify_activate_IRQ_req_sn2(nasid);
+
+ b = find_next_bit(&nasid_mask_long, BITS_PER_LONG,
+ b + 1);
+ } while (b < BITS_PER_LONG);
+ }
+ return n_IRQs_detected;
+}
+
+static void
+xpc_process_activate_IRQ_rcvd_sn2(void)
+{
+ unsigned long irq_flags;
+ int n_IRQs_expected;
+ int n_IRQs_detected;
+
+ DBUG_ON(xpc_activate_IRQ_rcvd == 0);
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ n_IRQs_expected = xpc_activate_IRQ_rcvd;
+ xpc_activate_IRQ_rcvd = 0;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ n_IRQs_detected = xpc_identify_activate_IRQ_sender_sn2();
+ if (n_IRQs_detected < n_IRQs_expected) {
+ /* retry once to help avoid missing amo */
+ (void)xpc_identify_activate_IRQ_sender_sn2();
+ }
+}
+
+/*
+ * Setup the channel structures that are sn2 specific.
+ */
+static enum xp_retval
+xpc_setup_ch_structures_sn_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ struct xpc_channel_sn2 *ch_sn2;
+ enum xp_retval retval;
+ int ret;
+ int cpuid;
+ int ch_number;
+ struct timer_list *timer;
+ short partid = XPC_PARTID(part);
+
+ /* allocate all the required GET/PUT values */
+
+ part_sn2->local_GPs =
+ xpc_kzalloc_cacheline_aligned(XPC_GP_SIZE, GFP_KERNEL,
+ &part_sn2->local_GPs_base);
+ if (part_sn2->local_GPs == NULL) {
+ dev_err(xpc_chan, "can't get memory for local get/put "
+ "values\n");
+ return xpNoMemory;
+ }
+
+ part_sn2->remote_GPs =
+ xpc_kzalloc_cacheline_aligned(XPC_GP_SIZE, GFP_KERNEL,
+ &part_sn2->remote_GPs_base);
+ if (part_sn2->remote_GPs == NULL) {
+ dev_err(xpc_chan, "can't get memory for remote get/put "
+ "values\n");
+ retval = xpNoMemory;
+ goto out_1;
+ }
+
+ part_sn2->remote_GPs_pa = 0;
+
+ /* allocate all the required open and close args */
+
+ part_sn2->local_openclose_args =
+ xpc_kzalloc_cacheline_aligned(XPC_OPENCLOSE_ARGS_SIZE,
+ GFP_KERNEL, &part_sn2->
+ local_openclose_args_base);
+ if (part_sn2->local_openclose_args == NULL) {
+ dev_err(xpc_chan, "can't get memory for local connect args\n");
+ retval = xpNoMemory;
+ goto out_2;
+ }
+
+ part_sn2->remote_openclose_args_pa = 0;
+
+ part_sn2->local_chctl_amo_va = xpc_init_IRQ_amo_sn2(partid);
+
+ part_sn2->notify_IRQ_nasid = 0;
+ part_sn2->notify_IRQ_phys_cpuid = 0;
+ part_sn2->remote_chctl_amo_va = NULL;
+
+ sprintf(part_sn2->notify_IRQ_owner, "xpc%02d", partid);
+ ret = request_irq(SGI_XPC_NOTIFY, xpc_handle_notify_IRQ_sn2,
+ IRQF_SHARED, part_sn2->notify_IRQ_owner,
+ (void *)(u64)partid);
+ if (ret != 0) {
+ dev_err(xpc_chan, "can't register NOTIFY IRQ handler, "
+ "errno=%d\n", -ret);
+ retval = xpLackOfResources;
+ goto out_3;
+ }
+
+ /* Setup a timer to check for dropped notify IRQs */
+ timer = &part_sn2->dropped_notify_IRQ_timer;
+ init_timer(timer);
+ timer->function =
+ (void (*)(unsigned long))xpc_check_for_dropped_notify_IRQ_sn2;
+ timer->data = (unsigned long)part;
+ timer->expires = jiffies + XPC_DROPPED_NOTIFY_IRQ_WAIT_INTERVAL;
+ add_timer(timer);
+
+ for (ch_number = 0; ch_number < part->nchannels; ch_number++) {
+ ch_sn2 = &part->channels[ch_number].sn.sn2;
+
+ ch_sn2->local_GP = &part_sn2->local_GPs[ch_number];
+ ch_sn2->local_openclose_args =
+ &part_sn2->local_openclose_args[ch_number];
+
+ mutex_init(&ch_sn2->msg_to_pull_mutex);
+ }
+
+ /*
+ * Setup the per partition specific variables required by the
+ * remote partition to establish channel connections with us.
+ *
+ * The setting of the magic # indicates that these per partition
+ * specific variables are ready to be used.
+ */
+ xpc_vars_part_sn2[partid].GPs_pa = xp_pa(part_sn2->local_GPs);
+ xpc_vars_part_sn2[partid].openclose_args_pa =
+ xp_pa(part_sn2->local_openclose_args);
+ xpc_vars_part_sn2[partid].chctl_amo_pa =
+ xp_pa(part_sn2->local_chctl_amo_va);
+ cpuid = raw_smp_processor_id(); /* any CPU in this partition will do */
+ xpc_vars_part_sn2[partid].notify_IRQ_nasid = cpuid_to_nasid(cpuid);
+ xpc_vars_part_sn2[partid].notify_IRQ_phys_cpuid =
+ cpu_physical_id(cpuid);
+ xpc_vars_part_sn2[partid].nchannels = part->nchannels;
+ xpc_vars_part_sn2[partid].magic = XPC_VP_MAGIC1_SN2;
+
+ return xpSuccess;
+
+ /* setup of ch structures failed */
+out_3:
+ kfree(part_sn2->local_openclose_args_base);
+ part_sn2->local_openclose_args = NULL;
+out_2:
+ kfree(part_sn2->remote_GPs_base);
+ part_sn2->remote_GPs = NULL;
+out_1:
+ kfree(part_sn2->local_GPs_base);
+ part_sn2->local_GPs = NULL;
+ return retval;
+}
+
+/*
+ * Teardown the channel structures that are sn2 specific.
+ */
+static void
+xpc_teardown_ch_structures_sn_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ short partid = XPC_PARTID(part);
+
+ /*
+ * Indicate that the variables specific to the remote partition are no
+ * longer available for its use.
+ */
+ xpc_vars_part_sn2[partid].magic = 0;
+
+ /* in case we've still got outstanding timers registered... */
+ del_timer_sync(&part_sn2->dropped_notify_IRQ_timer);
+ free_irq(SGI_XPC_NOTIFY, (void *)(u64)partid);
+
+ kfree(part_sn2->local_openclose_args_base);
+ part_sn2->local_openclose_args = NULL;
+ kfree(part_sn2->remote_GPs_base);
+ part_sn2->remote_GPs = NULL;
+ kfree(part_sn2->local_GPs_base);
+ part_sn2->local_GPs = NULL;
+ part_sn2->local_chctl_amo_va = NULL;
+}
+
+/*
+ * Create a wrapper that hides the underlying mechanism for pulling a cacheline
+ * (or multiple cachelines) from a remote partition.
+ *
+ * src_pa must be a cacheline aligned physical address on the remote partition.
+ * dst must be a cacheline aligned virtual address on this partition.
+ * cnt must be cacheline sized
+ */
+/* ??? Replace this function by call to xp_remote_memcpy() or bte_copy()? */
+static enum xp_retval
+xpc_pull_remote_cachelines_sn2(struct xpc_partition *part, void *dst,
+ const unsigned long src_pa, size_t cnt)
+{
+ enum xp_retval ret;
+
+ DBUG_ON(src_pa != L1_CACHE_ALIGN(src_pa));
+ DBUG_ON((unsigned long)dst != L1_CACHE_ALIGN((unsigned long)dst));
+ DBUG_ON(cnt != L1_CACHE_ALIGN(cnt));
+
+ if (part->act_state == XPC_P_AS_DEACTIVATING)
+ return part->reason;
+
+ ret = xp_remote_memcpy(xp_pa(dst), src_pa, cnt);
+ if (ret != xpSuccess) {
+ dev_dbg(xpc_chan, "xp_remote_memcpy() from partition %d failed,"
+ " ret=%d\n", XPC_PARTID(part), ret);
+ }
+ return ret;
+}
+
+/*
+ * Pull the remote per partition specific variables from the specified
+ * partition.
+ */
+static enum xp_retval
+xpc_pull_remote_vars_part_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ u8 buffer[L1_CACHE_BYTES * 2];
+ struct xpc_vars_part_sn2 *pulled_entry_cacheline =
+ (struct xpc_vars_part_sn2 *)L1_CACHE_ALIGN((u64)buffer);
+ struct xpc_vars_part_sn2 *pulled_entry;
+ unsigned long remote_entry_cacheline_pa;
+ unsigned long remote_entry_pa;
+ short partid = XPC_PARTID(part);
+ enum xp_retval ret;
+
+ /* pull the cacheline that contains the variables we're interested in */
+
+ DBUG_ON(part_sn2->remote_vars_part_pa !=
+ L1_CACHE_ALIGN(part_sn2->remote_vars_part_pa));
+ DBUG_ON(sizeof(struct xpc_vars_part_sn2) != L1_CACHE_BYTES / 2);
+
+ remote_entry_pa = part_sn2->remote_vars_part_pa +
+ sn_partition_id * sizeof(struct xpc_vars_part_sn2);
+
+ remote_entry_cacheline_pa = (remote_entry_pa & ~(L1_CACHE_BYTES - 1));
+
+ pulled_entry = (struct xpc_vars_part_sn2 *)((u64)pulled_entry_cacheline
+ + (remote_entry_pa &
+ (L1_CACHE_BYTES - 1)));
+
+ ret = xpc_pull_remote_cachelines_sn2(part, pulled_entry_cacheline,
+ remote_entry_cacheline_pa,
+ L1_CACHE_BYTES);
+ if (ret != xpSuccess) {
+ dev_dbg(xpc_chan, "failed to pull XPC vars_part from "
+ "partition %d, ret=%d\n", partid, ret);
+ return ret;
+ }
+
+ /* see if they've been set up yet */
+
+ if (pulled_entry->magic != XPC_VP_MAGIC1_SN2 &&
+ pulled_entry->magic != XPC_VP_MAGIC2_SN2) {
+
+ if (pulled_entry->magic != 0) {
+ dev_dbg(xpc_chan, "partition %d's XPC vars_part for "
+ "partition %d has bad magic value (=0x%lx)\n",
+ partid, sn_partition_id, pulled_entry->magic);
+ return xpBadMagic;
+ }
+
+ /* they've not been initialized yet */
+ return xpRetry;
+ }
+
+ if (xpc_vars_part_sn2[partid].magic == XPC_VP_MAGIC1_SN2) {
+
+ /* validate the variables */
+
+ if (pulled_entry->GPs_pa == 0 ||
+ pulled_entry->openclose_args_pa == 0 ||
+ pulled_entry->chctl_amo_pa == 0) {
+
+ dev_err(xpc_chan, "partition %d's XPC vars_part for "
+ "partition %d are not valid\n", partid,
+ sn_partition_id);
+ return xpInvalidAddress;
+ }
+
+ /* the variables we imported look to be valid */
+
+ part_sn2->remote_GPs_pa = pulled_entry->GPs_pa;
+ part_sn2->remote_openclose_args_pa =
+ pulled_entry->openclose_args_pa;
+ part_sn2->remote_chctl_amo_va =
+ (struct amo *)__va(pulled_entry->chctl_amo_pa);
+ part_sn2->notify_IRQ_nasid = pulled_entry->notify_IRQ_nasid;
+ part_sn2->notify_IRQ_phys_cpuid =
+ pulled_entry->notify_IRQ_phys_cpuid;
+
+ if (part->nchannels > pulled_entry->nchannels)
+ part->nchannels = pulled_entry->nchannels;
+
+ /* let the other side know that we've pulled their variables */
+
+ xpc_vars_part_sn2[partid].magic = XPC_VP_MAGIC2_SN2;
+ }
+
+ if (pulled_entry->magic == XPC_VP_MAGIC1_SN2)
+ return xpRetry;
+
+ return xpSuccess;
+}
+
+/*
+ * Establish first contact with the remote partititon. This involves pulling
+ * the XPC per partition variables from the remote partition and waiting for
+ * the remote partition to pull ours.
+ */
+static enum xp_retval
+xpc_make_first_contact_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ enum xp_retval ret;
+
+ /*
+ * Register the remote partition's amos with SAL so it can handle
+ * and cleanup errors within that address range should the remote
+ * partition go down. We don't unregister this range because it is
+ * difficult to tell when outstanding writes to the remote partition
+ * are finished and thus when it is safe to unregister. This should
+ * not result in wasted space in the SAL xp_addr_region table because
+ * we should get the same page for remote_amos_page_pa after module
+ * reloads and system reboots.
+ */
+ if (sn_register_xp_addr_region(part_sn2->remote_amos_page_pa,
+ PAGE_SIZE, 1) < 0) {
+ dev_warn(xpc_part, "xpc_activating(%d) failed to register "
+ "xp_addr region\n", XPC_PARTID(part));
+
+ ret = xpPhysAddrRegFailed;
+ XPC_DEACTIVATE_PARTITION(part, ret);
+ return ret;
+ }
+
+ /*
+ * Send activate IRQ to get other side to activate if they've not
+ * already begun to do so.
+ */
+ xpc_send_activate_IRQ_sn2(part_sn2->remote_amos_page_pa,
+ cnodeid_to_nasid(0),
+ part_sn2->activate_IRQ_nasid,
+ part_sn2->activate_IRQ_phys_cpuid);
+
+ while ((ret = xpc_pull_remote_vars_part_sn2(part)) != xpSuccess) {
+ if (ret != xpRetry) {
+ XPC_DEACTIVATE_PARTITION(part, ret);
+ return ret;
+ }
+
+ dev_dbg(xpc_part, "waiting to make first contact with "
+ "partition %d\n", XPC_PARTID(part));
+
+ /* wait a 1/4 of a second or so */
+ (void)msleep_interruptible(250);
+
+ if (part->act_state == XPC_P_AS_DEACTIVATING)
+ return part->reason;
+ }
+
+ return xpSuccess;
+}
+
+/*
+ * Get the chctl flags and pull the openclose args and/or remote GPs as needed.
+ */
+static u64
+xpc_get_chctl_all_flags_sn2(struct xpc_partition *part)
+{
+ struct xpc_partition_sn2 *part_sn2 = &part->sn.sn2;
+ unsigned long irq_flags;
+ union xpc_channel_ctl_flags chctl;
+ enum xp_retval ret;
+
+ /*
+ * See if there are any chctl flags to be handled.
+ */
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ chctl = part->chctl;
+ if (chctl.all_flags != 0)
+ part->chctl.all_flags = 0;
+
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ if (xpc_any_openclose_chctl_flags_set(&chctl)) {
+ ret = xpc_pull_remote_cachelines_sn2(part, part->
+ remote_openclose_args,
+ part_sn2->
+ remote_openclose_args_pa,
+ XPC_OPENCLOSE_ARGS_SIZE);
+ if (ret != xpSuccess) {
+ XPC_DEACTIVATE_PARTITION(part, ret);
+
+ dev_dbg(xpc_chan, "failed to pull openclose args from "
+ "partition %d, ret=%d\n", XPC_PARTID(part),
+ ret);
+
+ /* don't bother processing chctl flags anymore */
+ chctl.all_flags = 0;
+ }
+ }
+
+ if (xpc_any_msg_chctl_flags_set(&chctl)) {
+ ret = xpc_pull_remote_cachelines_sn2(part, part_sn2->remote_GPs,
+ part_sn2->remote_GPs_pa,
+ XPC_GP_SIZE);
+ if (ret != xpSuccess) {
+ XPC_DEACTIVATE_PARTITION(part, ret);
+
+ dev_dbg(xpc_chan, "failed to pull GPs from partition "
+ "%d, ret=%d\n", XPC_PARTID(part), ret);
+
+ /* don't bother processing chctl flags anymore */
+ chctl.all_flags = 0;
+ }
+ }
+
+ return chctl.all_flags;
+}
+
+/*
+ * Allocate the local message queue and the notify queue.
+ */
+static enum xp_retval
+xpc_allocate_local_msgqueue_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ unsigned long irq_flags;
+ int nentries;
+ size_t nbytes;
+
+ for (nentries = ch->local_nentries; nentries > 0; nentries--) {
+
+ nbytes = nentries * ch->entry_size;
+ ch_sn2->local_msgqueue =
+ xpc_kzalloc_cacheline_aligned(nbytes, GFP_KERNEL,
+ &ch_sn2->local_msgqueue_base);
+ if (ch_sn2->local_msgqueue == NULL)
+ continue;
+
+ nbytes = nentries * sizeof(struct xpc_notify_sn2);
+ ch_sn2->notify_queue = kzalloc(nbytes, GFP_KERNEL);
+ if (ch_sn2->notify_queue == NULL) {
+ kfree(ch_sn2->local_msgqueue_base);
+ ch_sn2->local_msgqueue = NULL;
+ continue;
+ }
+
+ spin_lock_irqsave(&ch->lock, irq_flags);
+ if (nentries < ch->local_nentries) {
+ dev_dbg(xpc_chan, "nentries=%d local_nentries=%d, "
+ "partid=%d, channel=%d\n", nentries,
+ ch->local_nentries, ch->partid, ch->number);
+
+ ch->local_nentries = nentries;
+ }
+ spin_unlock_irqrestore(&ch->lock, irq_flags);
+ return xpSuccess;
+ }
+
+ dev_dbg(xpc_chan, "can't get memory for local message queue and notify "
+ "queue, partid=%d, channel=%d\n", ch->partid, ch->number);
+ return xpNoMemory;
+}
+
+/*
+ * Allocate the cached remote message queue.
+ */
+static enum xp_retval
+xpc_allocate_remote_msgqueue_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ unsigned long irq_flags;
+ int nentries;
+ size_t nbytes;
+
+ DBUG_ON(ch->remote_nentries <= 0);
+
+ for (nentries = ch->remote_nentries; nentries > 0; nentries--) {
+
+ nbytes = nentries * ch->entry_size;
+ ch_sn2->remote_msgqueue =
+ xpc_kzalloc_cacheline_aligned(nbytes, GFP_KERNEL, &ch_sn2->
+ remote_msgqueue_base);
+ if (ch_sn2->remote_msgqueue == NULL)
+ continue;
+
+ spin_lock_irqsave(&ch->lock, irq_flags);
+ if (nentries < ch->remote_nentries) {
+ dev_dbg(xpc_chan, "nentries=%d remote_nentries=%d, "
+ "partid=%d, channel=%d\n", nentries,
+ ch->remote_nentries, ch->partid, ch->number);
+
+ ch->remote_nentries = nentries;
+ }
+ spin_unlock_irqrestore(&ch->lock, irq_flags);
+ return xpSuccess;
+ }
+
+ dev_dbg(xpc_chan, "can't get memory for cached remote message queue, "
+ "partid=%d, channel=%d\n", ch->partid, ch->number);
+ return xpNoMemory;
+}
+
+/*
+ * Allocate message queues and other stuff associated with a channel.
+ *
+ * Note: Assumes all of the channel sizes are filled in.
+ */
+static enum xp_retval
+xpc_setup_msg_structures_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ enum xp_retval ret;
+
+ DBUG_ON(ch->flags & XPC_C_SETUP);
+
+ ret = xpc_allocate_local_msgqueue_sn2(ch);
+ if (ret == xpSuccess) {
+
+ ret = xpc_allocate_remote_msgqueue_sn2(ch);
+ if (ret != xpSuccess) {
+ kfree(ch_sn2->local_msgqueue_base);
+ ch_sn2->local_msgqueue = NULL;
+ kfree(ch_sn2->notify_queue);
+ ch_sn2->notify_queue = NULL;
+ }
+ }
+ return ret;
+}
+
+/*
+ * Free up message queues and other stuff that were allocated for the specified
+ * channel.
+ */
+static void
+xpc_teardown_msg_structures_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+
+ DBUG_ON(!spin_is_locked(&ch->lock));
+
+ ch_sn2->remote_msgqueue_pa = 0;
+
+ ch_sn2->local_GP->get = 0;
+ ch_sn2->local_GP->put = 0;
+ ch_sn2->remote_GP.get = 0;
+ ch_sn2->remote_GP.put = 0;
+ ch_sn2->w_local_GP.get = 0;
+ ch_sn2->w_local_GP.put = 0;
+ ch_sn2->w_remote_GP.get = 0;
+ ch_sn2->w_remote_GP.put = 0;
+ ch_sn2->next_msg_to_pull = 0;
+
+ if (ch->flags & XPC_C_SETUP) {
+ dev_dbg(xpc_chan, "ch->flags=0x%x, partid=%d, channel=%d\n",
+ ch->flags, ch->partid, ch->number);
+
+ kfree(ch_sn2->local_msgqueue_base);
+ ch_sn2->local_msgqueue = NULL;
+ kfree(ch_sn2->remote_msgqueue_base);
+ ch_sn2->remote_msgqueue = NULL;
+ kfree(ch_sn2->notify_queue);
+ ch_sn2->notify_queue = NULL;
+ }
+}
+
+/*
+ * Notify those who wanted to be notified upon delivery of their message.
+ */
+static void
+xpc_notify_senders_sn2(struct xpc_channel *ch, enum xp_retval reason, s64 put)
+{
+ struct xpc_notify_sn2 *notify;
+ u8 notify_type;
+ s64 get = ch->sn.sn2.w_remote_GP.get - 1;
+
+ while (++get < put && atomic_read(&ch->n_to_notify) > 0) {
+
+ notify = &ch->sn.sn2.notify_queue[get % ch->local_nentries];
+
+ /*
+ * See if the notify entry indicates it was associated with
+ * a message who's sender wants to be notified. It is possible
+ * that it is, but someone else is doing or has done the
+ * notification.
+ */
+ notify_type = notify->type;
+ if (notify_type == 0 ||
+ cmpxchg(¬ify->type, notify_type, 0) != notify_type) {
+ continue;
+ }
+
+ DBUG_ON(notify_type != XPC_N_CALL);
+
+ atomic_dec(&ch->n_to_notify);
+
+ if (notify->func != NULL) {
+ dev_dbg(xpc_chan, "notify->func() called, notify=0x%p "
+ "msg_number=%ld partid=%d channel=%d\n",
+ (void *)notify, get, ch->partid, ch->number);
+
+ notify->func(reason, ch->partid, ch->number,
+ notify->key);
+
+ dev_dbg(xpc_chan, "notify->func() returned, notify=0x%p"
+ " msg_number=%ld partid=%d channel=%d\n",
+ (void *)notify, get, ch->partid, ch->number);
+ }
+ }
+}
+
+static void
+xpc_notify_senders_of_disconnect_sn2(struct xpc_channel *ch)
+{
+ xpc_notify_senders_sn2(ch, ch->reason, ch->sn.sn2.w_local_GP.put);
+}
+
+/*
+ * Clear some of the msg flags in the local message queue.
+ */
+static inline void
+xpc_clear_local_msgqueue_flags_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ s64 get;
+
+ get = ch_sn2->w_remote_GP.get;
+ do {
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->local_msgqueue +
+ (get % ch->local_nentries) *
+ ch->entry_size);
+ msg->flags = 0;
+ } while (++get < ch_sn2->remote_GP.get);
+}
+
+/*
+ * Clear some of the msg flags in the remote message queue.
+ */
+static inline void
+xpc_clear_remote_msgqueue_flags_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ s64 put;
+
+ put = ch_sn2->w_remote_GP.put;
+ do {
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->remote_msgqueue +
+ (put % ch->remote_nentries) *
+ ch->entry_size);
+ msg->flags = 0;
+ } while (++put < ch_sn2->remote_GP.put);
+}
+
+static int
+xpc_n_of_deliverable_payloads_sn2(struct xpc_channel *ch)
+{
+ return ch->sn.sn2.w_remote_GP.put - ch->sn.sn2.w_local_GP.get;
+}
+
+static void
+xpc_process_msg_chctl_flags_sn2(struct xpc_partition *part, int ch_number)
+{
+ struct xpc_channel *ch = &part->channels[ch_number];
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ int npayloads_sent;
+
+ ch_sn2->remote_GP = part->sn.sn2.remote_GPs[ch_number];
+
+ /* See what, if anything, has changed for each connected channel */
+
+ xpc_msgqueue_ref(ch);
+
+ if (ch_sn2->w_remote_GP.get == ch_sn2->remote_GP.get &&
+ ch_sn2->w_remote_GP.put == ch_sn2->remote_GP.put) {
+ /* nothing changed since GPs were last pulled */
+ xpc_msgqueue_deref(ch);
+ return;
+ }
+
+ if (!(ch->flags & XPC_C_CONNECTED)) {
+ xpc_msgqueue_deref(ch);
+ return;
+ }
+
+ /*
+ * First check to see if messages recently sent by us have been
+ * received by the other side. (The remote GET value will have
+ * changed since we last looked at it.)
+ */
+
+ if (ch_sn2->w_remote_GP.get != ch_sn2->remote_GP.get) {
+
+ /*
+ * We need to notify any senders that want to be notified
+ * that their sent messages have been received by their
+ * intended recipients. We need to do this before updating
+ * w_remote_GP.get so that we don't allocate the same message
+ * queue entries prematurely (see xpc_allocate_msg()).
+ */
+ if (atomic_read(&ch->n_to_notify) > 0) {
+ /*
+ * Notify senders that messages sent have been
+ * received and delivered by the other side.
+ */
+ xpc_notify_senders_sn2(ch, xpMsgDelivered,
+ ch_sn2->remote_GP.get);
+ }
+
+ /*
+ * Clear msg->flags in previously sent messages, so that
+ * they're ready for xpc_allocate_msg().
+ */
+ xpc_clear_local_msgqueue_flags_sn2(ch);
+
+ ch_sn2->w_remote_GP.get = ch_sn2->remote_GP.get;
+
+ dev_dbg(xpc_chan, "w_remote_GP.get changed to %ld, partid=%d, "
+ "channel=%d\n", ch_sn2->w_remote_GP.get, ch->partid,
+ ch->number);
+
+ /*
+ * If anyone was waiting for message queue entries to become
+ * available, wake them up.
+ */
+ if (atomic_read(&ch->n_on_msg_allocate_wq) > 0)
+ wake_up(&ch->msg_allocate_wq);
+ }
+
+ /*
+ * Now check for newly sent messages by the other side. (The remote
+ * PUT value will have changed since we last looked at it.)
+ */
+
+ if (ch_sn2->w_remote_GP.put != ch_sn2->remote_GP.put) {
+ /*
+ * Clear msg->flags in previously received messages, so that
+ * they're ready for xpc_get_deliverable_payload_sn2().
+ */
+ xpc_clear_remote_msgqueue_flags_sn2(ch);
+
+ ch_sn2->w_remote_GP.put = ch_sn2->remote_GP.put;
+
+ dev_dbg(xpc_chan, "w_remote_GP.put changed to %ld, partid=%d, "
+ "channel=%d\n", ch_sn2->w_remote_GP.put, ch->partid,
+ ch->number);
+
+ npayloads_sent = xpc_n_of_deliverable_payloads_sn2(ch);
+ if (npayloads_sent > 0) {
+ dev_dbg(xpc_chan, "msgs waiting to be copied and "
+ "delivered=%d, partid=%d, channel=%d\n",
+ npayloads_sent, ch->partid, ch->number);
+
+ if (ch->flags & XPC_C_CONNECTEDCALLOUT_MADE)
+ xpc_activate_kthreads(ch, npayloads_sent);
+ }
+ }
+
+ xpc_msgqueue_deref(ch);
+}
+
+static struct xpc_msg_sn2 *
+xpc_pull_remote_msg_sn2(struct xpc_channel *ch, s64 get)
+{
+ struct xpc_partition *part = &xpc_partitions[ch->partid];
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ unsigned long remote_msg_pa;
+ struct xpc_msg_sn2 *msg;
+ u32 msg_index;
+ u32 nmsgs;
+ u64 msg_offset;
+ enum xp_retval ret;
+
+ if (mutex_lock_interruptible(&ch_sn2->msg_to_pull_mutex) != 0) {
+ /* we were interrupted by a signal */
+ return NULL;
+ }
+
+ while (get >= ch_sn2->next_msg_to_pull) {
+
+ /* pull as many messages as are ready and able to be pulled */
+
+ msg_index = ch_sn2->next_msg_to_pull % ch->remote_nentries;
+
+ DBUG_ON(ch_sn2->next_msg_to_pull >= ch_sn2->w_remote_GP.put);
+ nmsgs = ch_sn2->w_remote_GP.put - ch_sn2->next_msg_to_pull;
+ if (msg_index + nmsgs > ch->remote_nentries) {
+ /* ignore the ones that wrap the msg queue for now */
+ nmsgs = ch->remote_nentries - msg_index;
+ }
+
+ msg_offset = msg_index * ch->entry_size;
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->remote_msgqueue +
+ msg_offset);
+ remote_msg_pa = ch_sn2->remote_msgqueue_pa + msg_offset;
+
+ ret = xpc_pull_remote_cachelines_sn2(part, msg, remote_msg_pa,
+ nmsgs * ch->entry_size);
+ if (ret != xpSuccess) {
+
+ dev_dbg(xpc_chan, "failed to pull %d msgs starting with"
+ " msg %ld from partition %d, channel=%d, "
+ "ret=%d\n", nmsgs, ch_sn2->next_msg_to_pull,
+ ch->partid, ch->number, ret);
+
+ XPC_DEACTIVATE_PARTITION(part, ret);
+
+ mutex_unlock(&ch_sn2->msg_to_pull_mutex);
+ return NULL;
+ }
+
+ ch_sn2->next_msg_to_pull += nmsgs;
+ }
+
+ mutex_unlock(&ch_sn2->msg_to_pull_mutex);
+
+ /* return the message we were looking for */
+ msg_offset = (get % ch->remote_nentries) * ch->entry_size;
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->remote_msgqueue + msg_offset);
+
+ return msg;
+}
+
+/*
+ * Get the next deliverable message's payload.
+ */
+static void *
+xpc_get_deliverable_payload_sn2(struct xpc_channel *ch)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ void *payload = NULL;
+ s64 get;
+
+ do {
+ if (ch->flags & XPC_C_DISCONNECTING)
+ break;
+
+ get = ch_sn2->w_local_GP.get;
+ rmb(); /* guarantee that .get loads before .put */
+ if (get == ch_sn2->w_remote_GP.put)
+ break;
+
+ /* There are messages waiting to be pulled and delivered.
+ * We need to try to secure one for ourselves. We'll do this
+ * by trying to increment w_local_GP.get and hope that no one
+ * else beats us to it. If they do, we'll we'll simply have
+ * to try again for the next one.
+ */
+
+ if (cmpxchg(&ch_sn2->w_local_GP.get, get, get + 1) == get) {
+ /* we got the entry referenced by get */
+
+ dev_dbg(xpc_chan, "w_local_GP.get changed to %ld, "
+ "partid=%d, channel=%d\n", get + 1,
+ ch->partid, ch->number);
+
+ /* pull the message from the remote partition */
+
+ msg = xpc_pull_remote_msg_sn2(ch, get);
+
+ DBUG_ON(msg != NULL && msg->number != get);
+ DBUG_ON(msg != NULL && (msg->flags & XPC_M_SN2_DONE));
+ DBUG_ON(msg != NULL && !(msg->flags & XPC_M_SN2_READY));
+
+ payload = &msg->payload;
+ break;
+ }
+
+ } while (1);
+
+ return payload;
+}
+
+/*
+ * Now we actually send the messages that are ready to be sent by advancing
+ * the local message queue's Put value and then send a chctl msgrequest to the
+ * recipient partition.
+ */
+static void
+xpc_send_msgs_sn2(struct xpc_channel *ch, s64 initial_put)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ s64 put = initial_put + 1;
+ int send_msgrequest = 0;
+
+ while (1) {
+
+ while (1) {
+ if (put == ch_sn2->w_local_GP.put)
+ break;
+
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->
+ local_msgqueue + (put %
+ ch->local_nentries) *
+ ch->entry_size);
+
+ if (!(msg->flags & XPC_M_SN2_READY))
+ break;
+
+ put++;
+ }
+
+ if (put == initial_put) {
+ /* nothing's changed */
+ break;
+ }
+
+ if (cmpxchg_rel(&ch_sn2->local_GP->put, initial_put, put) !=
+ initial_put) {
+ /* someone else beat us to it */
+ DBUG_ON(ch_sn2->local_GP->put < initial_put);
+ break;
+ }
+
+ /* we just set the new value of local_GP->put */
+
+ dev_dbg(xpc_chan, "local_GP->put changed to %ld, partid=%d, "
+ "channel=%d\n", put, ch->partid, ch->number);
+
+ send_msgrequest = 1;
+
+ /*
+ * We need to ensure that the message referenced by
+ * local_GP->put is not XPC_M_SN2_READY or that local_GP->put
+ * equals w_local_GP.put, so we'll go have a look.
+ */
+ initial_put = put;
+ }
+
+ if (send_msgrequest)
+ xpc_send_chctl_msgrequest_sn2(ch);
+}
+
+/*
+ * Allocate an entry for a message from the message queue associated with the
+ * specified channel.
+ */
+static enum xp_retval
+xpc_allocate_msg_sn2(struct xpc_channel *ch, u32 flags,
+ struct xpc_msg_sn2 **address_of_msg)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ enum xp_retval ret;
+ s64 put;
+
+ /*
+ * Get the next available message entry from the local message queue.
+ * If none are available, we'll make sure that we grab the latest
+ * GP values.
+ */
+ ret = xpTimeout;
+
+ while (1) {
+
+ put = ch_sn2->w_local_GP.put;
+ rmb(); /* guarantee that .put loads before .get */
+ if (put - ch_sn2->w_remote_GP.get < ch->local_nentries) {
+
+ /* There are available message entries. We need to try
+ * to secure one for ourselves. We'll do this by trying
+ * to increment w_local_GP.put as long as someone else
+ * doesn't beat us to it. If they do, we'll have to
+ * try again.
+ */
+ if (cmpxchg(&ch_sn2->w_local_GP.put, put, put + 1) ==
+ put) {
+ /* we got the entry referenced by put */
+ break;
+ }
+ continue; /* try again */
+ }
+
+ /*
+ * There aren't any available msg entries at this time.
+ *
+ * In waiting for a message entry to become available,
+ * we set a timeout in case the other side is not sending
+ * completion interrupts. This lets us fake a notify IRQ
+ * that will cause the notify IRQ handler to fetch the latest
+ * GP values as if an interrupt was sent by the other side.
+ */
+ if (ret == xpTimeout)
+ xpc_send_chctl_local_msgrequest_sn2(ch);
+
+ if (flags & XPC_NOWAIT)
+ return xpNoWait;
+
+ ret = xpc_allocate_msg_wait(ch);
+ if (ret != xpInterrupted && ret != xpTimeout)
+ return ret;
+ }
+
+ /* get the message's address and initialize it */
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->local_msgqueue +
+ (put % ch->local_nentries) *
+ ch->entry_size);
+
+ DBUG_ON(msg->flags != 0);
+ msg->number = put;
+
+ dev_dbg(xpc_chan, "w_local_GP.put changed to %ld; msg=0x%p, "
+ "msg_number=%ld, partid=%d, channel=%d\n", put + 1,
+ (void *)msg, msg->number, ch->partid, ch->number);
+
+ *address_of_msg = msg;
+ return xpSuccess;
+}
+
+/*
+ * Common code that does the actual sending of the message by advancing the
+ * local message queue's Put value and sends a chctl msgrequest to the
+ * partition the message is being sent to.
+ */
+static enum xp_retval
+xpc_send_payload_sn2(struct xpc_channel *ch, u32 flags, void *payload,
+ u16 payload_size, u8 notify_type, xpc_notify_func func,
+ void *key)
+{
+ enum xp_retval ret = xpSuccess;
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg = msg;
+ struct xpc_notify_sn2 *notify = notify;
+ s64 msg_number;
+ s64 put;
+
+ DBUG_ON(notify_type == XPC_N_CALL && func == NULL);
+
+ if (XPC_MSG_SIZE(payload_size) > ch->entry_size)
+ return xpPayloadTooBig;
+
+ xpc_msgqueue_ref(ch);
+
+ if (ch->flags & XPC_C_DISCONNECTING) {
+ ret = ch->reason;
+ goto out_1;
+ }
+ if (!(ch->flags & XPC_C_CONNECTED)) {
+ ret = xpNotConnected;
+ goto out_1;
+ }
+
+ ret = xpc_allocate_msg_sn2(ch, flags, &msg);
+ if (ret != xpSuccess)
+ goto out_1;
+
+ msg_number = msg->number;
+
+ if (notify_type != 0) {
+ /*
+ * Tell the remote side to send an ACK interrupt when the
+ * message has been delivered.
+ */
+ msg->flags |= XPC_M_SN2_INTERRUPT;
+
+ atomic_inc(&ch->n_to_notify);
+
+ notify = &ch_sn2->notify_queue[msg_number % ch->local_nentries];
+ notify->func = func;
+ notify->key = key;
+ notify->type = notify_type;
+
+ /* ??? Is a mb() needed here? */
+
+ if (ch->flags & XPC_C_DISCONNECTING) {
+ /*
+ * An error occurred between our last error check and
+ * this one. We will try to clear the type field from
+ * the notify entry. If we succeed then
+ * xpc_disconnect_channel() didn't already process
+ * the notify entry.
+ */
+ if (cmpxchg(¬ify->type, notify_type, 0) ==
+ notify_type) {
+ atomic_dec(&ch->n_to_notify);
+ ret = ch->reason;
+ }
+ goto out_1;
+ }
+ }
+
+ memcpy(&msg->payload, payload, payload_size);
+
+ msg->flags |= XPC_M_SN2_READY;
+
+ /*
+ * The preceding store of msg->flags must occur before the following
+ * load of local_GP->put.
+ */
+ mb();
+
+ /* see if the message is next in line to be sent, if so send it */
+
+ put = ch_sn2->local_GP->put;
+ if (put == msg_number)
+ xpc_send_msgs_sn2(ch, put);
+
+out_1:
+ xpc_msgqueue_deref(ch);
+ return ret;
+}
+
+/*
+ * Now we actually acknowledge the messages that have been delivered and ack'd
+ * by advancing the cached remote message queue's Get value and if requested
+ * send a chctl msgrequest to the message sender's partition.
+ *
+ * If a message has XPC_M_SN2_INTERRUPT set, send an interrupt to the partition
+ * that sent the message.
+ */
+static void
+xpc_acknowledge_msgs_sn2(struct xpc_channel *ch, s64 initial_get, u8 msg_flags)
+{
+ struct xpc_channel_sn2 *ch_sn2 = &ch->sn.sn2;
+ struct xpc_msg_sn2 *msg;
+ s64 get = initial_get + 1;
+ int send_msgrequest = 0;
+
+ while (1) {
+
+ while (1) {
+ if (get == ch_sn2->w_local_GP.get)
+ break;
+
+ msg = (struct xpc_msg_sn2 *)((u64)ch_sn2->
+ remote_msgqueue + (get %
+ ch->remote_nentries) *
+ ch->entry_size);
+
+ if (!(msg->flags & XPC_M_SN2_DONE))
+ break;
+
+ msg_flags |= msg->flags;
+ get++;
+ }
+
+ if (get == initial_get) {
+ /* nothing's changed */
+ break;
+ }
+
+ if (cmpxchg_rel(&ch_sn2->local_GP->get, initial_get, get) !=
+ initial_get) {
+ /* someone else beat us to it */
+ DBUG_ON(ch_sn2->local_GP->get <= initial_get);
+ break;
+ }
+
+ /* we just set the new value of local_GP->get */
+
+ dev_dbg(xpc_chan, "local_GP->get changed to %ld, partid=%d, "
+ "channel=%d\n", get, ch->partid, ch->number);
+
+ send_msgrequest = (msg_flags & XPC_M_SN2_INTERRUPT);
+
+ /*
+ * We need to ensure that the message referenced by
+ * local_GP->get is not XPC_M_SN2_DONE or that local_GP->get
+ * equals w_local_GP.get, so we'll go have a look.
+ */
+ initial_get = get;
+ }
+
+ if (send_msgrequest)
+ xpc_send_chctl_msgrequest_sn2(ch);
+}
+
+static void
+xpc_received_payload_sn2(struct xpc_channel *ch, void *payload)
+{
+ struct xpc_msg_sn2 *msg;
+ s64 msg_number;
+ s64 get;
+
+ msg = container_of(payload, struct xpc_msg_sn2, payload);
+ msg_number = msg->number;
+
+ dev_dbg(xpc_chan, "msg=0x%p, msg_number=%ld, partid=%d, channel=%d\n",
+ (void *)msg, msg_number, ch->partid, ch->number);
+
+ DBUG_ON((((u64)msg - (u64)ch->remote_msgqueue) / ch->entry_size) !=
+ msg_number % ch->remote_nentries);
+ DBUG_ON(msg->flags & XPC_M_SN2_DONE);
+
+ msg->flags |= XPC_M_SN2_DONE;
+
+ /*
+ * The preceding store of msg->flags must occur before the following
+ * load of local_GP->get.
+ */
+ mb();
+
+ /*
+ * See if this message is next in line to be acknowledged as having
+ * been delivered.
+ */
+ get = ch->sn.sn2.local_GP->get;
+ if (get == msg_number)
+ xpc_acknowledge_msgs_sn2(ch, get, msg->flags);
+}
+
+int
+xpc_init_sn2(void)
+{
+ int ret;
+ size_t buf_size;
+
+ xpc_setup_partitions_sn = xpc_setup_partitions_sn_sn2;
+ xpc_get_partition_rsvd_page_pa = xpc_get_partition_rsvd_page_pa_sn2;
+ xpc_setup_rsvd_page_sn = xpc_setup_rsvd_page_sn_sn2;
+ xpc_increment_heartbeat = xpc_increment_heartbeat_sn2;
+ xpc_offline_heartbeat = xpc_offline_heartbeat_sn2;
+ xpc_online_heartbeat = xpc_online_heartbeat_sn2;
+ xpc_heartbeat_init = xpc_heartbeat_init_sn2;
+ xpc_heartbeat_exit = xpc_heartbeat_exit_sn2;
+ xpc_get_remote_heartbeat = xpc_get_remote_heartbeat_sn2;
+
+ xpc_request_partition_activation = xpc_request_partition_activation_sn2;
+ xpc_request_partition_reactivation =
+ xpc_request_partition_reactivation_sn2;
+ xpc_request_partition_deactivation =
+ xpc_request_partition_deactivation_sn2;
+ xpc_cancel_partition_deactivation_request =
+ xpc_cancel_partition_deactivation_request_sn2;
+
+ xpc_process_activate_IRQ_rcvd = xpc_process_activate_IRQ_rcvd_sn2;
+ xpc_setup_ch_structures_sn = xpc_setup_ch_structures_sn_sn2;
+ xpc_teardown_ch_structures_sn = xpc_teardown_ch_structures_sn_sn2;
+ xpc_make_first_contact = xpc_make_first_contact_sn2;
+
+ xpc_get_chctl_all_flags = xpc_get_chctl_all_flags_sn2;
+ xpc_send_chctl_closerequest = xpc_send_chctl_closerequest_sn2;
+ xpc_send_chctl_closereply = xpc_send_chctl_closereply_sn2;
+ xpc_send_chctl_openrequest = xpc_send_chctl_openrequest_sn2;
+ xpc_send_chctl_openreply = xpc_send_chctl_openreply_sn2;
+
+ xpc_save_remote_msgqueue_pa = xpc_save_remote_msgqueue_pa_sn2;
+
+ xpc_setup_msg_structures = xpc_setup_msg_structures_sn2;
+ xpc_teardown_msg_structures = xpc_teardown_msg_structures_sn2;
+
+ xpc_notify_senders_of_disconnect = xpc_notify_senders_of_disconnect_sn2;
+ xpc_process_msg_chctl_flags = xpc_process_msg_chctl_flags_sn2;
+ xpc_n_of_deliverable_payloads = xpc_n_of_deliverable_payloads_sn2;
+ xpc_get_deliverable_payload = xpc_get_deliverable_payload_sn2;
+
+ xpc_indicate_partition_engaged = xpc_indicate_partition_engaged_sn2;
+ xpc_indicate_partition_disengaged =
+ xpc_indicate_partition_disengaged_sn2;
+ xpc_partition_engaged = xpc_partition_engaged_sn2;
+ xpc_any_partition_engaged = xpc_any_partition_engaged_sn2;
+ xpc_assume_partition_disengaged = xpc_assume_partition_disengaged_sn2;
+
+ xpc_send_payload = xpc_send_payload_sn2;
+ xpc_received_payload = xpc_received_payload_sn2;
+
+ if (offsetof(struct xpc_msg_sn2, payload) > XPC_MSG_HDR_MAX_SIZE) {
+ dev_err(xpc_part, "header portion of struct xpc_msg_sn2 is "
+ "larger than %d\n", XPC_MSG_HDR_MAX_SIZE);
+ return -E2BIG;
+ }
+
+ buf_size = max(XPC_RP_VARS_SIZE,
+ XPC_RP_HEADER_SIZE + XP_NASID_MASK_BYTES_SN2);
+ xpc_remote_copy_buffer_sn2 = xpc_kmalloc_cacheline_aligned(buf_size,
+ GFP_KERNEL,
+ &xpc_remote_copy_buffer_base_sn2);
+ if (xpc_remote_copy_buffer_sn2 == NULL) {
+ dev_err(xpc_part, "can't get memory for remote copy buffer\n");
+ return -ENOMEM;
+ }
+
+ /* open up protections for IPI and [potentially] amo operations */
+ xpc_allow_IPI_ops_sn2();
+ xpc_allow_amo_ops_shub_wars_1_1_sn2();
+
+ /*
+ * This is safe to do before the xpc_hb_checker thread has started
+ * because the handler releases a wait queue. If an interrupt is
+ * received before the thread is waiting, it will not go to sleep,
+ * but rather immediately process the interrupt.
+ */
+ ret = request_irq(SGI_XPC_ACTIVATE, xpc_handle_activate_IRQ_sn2, 0,
+ "xpc hb", NULL);
+ if (ret != 0) {
+ dev_err(xpc_part, "can't register ACTIVATE IRQ handler, "
+ "errno=%d\n", -ret);
+ xpc_disallow_IPI_ops_sn2();
+ kfree(xpc_remote_copy_buffer_base_sn2);
+ }
+ return ret;
+}
+
+void
+xpc_exit_sn2(void)
+{
+ free_irq(SGI_XPC_ACTIVATE, NULL);
+ xpc_disallow_IPI_ops_sn2();
+ kfree(xpc_remote_copy_buffer_base_sn2);
+}
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2008 Silicon Graphics, Inc. All Rights Reserved.
+ */
+
+/*
+ * Cross Partition Communication (XPC) uv-based functions.
+ *
+ * Architecture specific implementation of common functions.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <asm/uv/uv_hub.h>
+#include "../sgi-gru/gru.h"
+#include "../sgi-gru/grukservices.h"
+#include "xpc.h"
+
+static atomic64_t xpc_heartbeat_uv;
+static DECLARE_BITMAP(xpc_heartbeating_to_mask_uv, XP_MAX_NPARTITIONS_UV);
+
+#define XPC_ACTIVATE_MSG_SIZE_UV (1 * GRU_CACHE_LINE_BYTES)
+#define XPC_NOTIFY_MSG_SIZE_UV (2 * GRU_CACHE_LINE_BYTES)
+
+#define XPC_ACTIVATE_MQ_SIZE_UV (4 * XP_MAX_NPARTITIONS_UV * \
+ XPC_ACTIVATE_MSG_SIZE_UV)
+#define XPC_NOTIFY_MQ_SIZE_UV (4 * XP_MAX_NPARTITIONS_UV * \
+ XPC_NOTIFY_MSG_SIZE_UV)
+
+static void *xpc_activate_mq_uv;
+static void *xpc_notify_mq_uv;
+
+static int
+xpc_setup_partitions_sn_uv(void)
+{
+ short partid;
+ struct xpc_partition_uv *part_uv;
+
+ for (partid = 0; partid < XP_MAX_NPARTITIONS_UV; partid++) {
+ part_uv = &xpc_partitions[partid].sn.uv;
+
+ spin_lock_init(&part_uv->flags_lock);
+ part_uv->remote_act_state = XPC_P_AS_INACTIVE;
+ }
+ return 0;
+}
+
+static void *
+xpc_create_gru_mq_uv(unsigned int mq_size, int cpuid, unsigned int irq,
+ irq_handler_t irq_handler)
+{
+ int ret;
+ int nid;
+ int mq_order;
+ struct page *page;
+ void *mq;
+
+ nid = cpu_to_node(cpuid);
+ mq_order = get_order(mq_size);
+ page = alloc_pages_node(nid, GFP_KERNEL | __GFP_ZERO | GFP_THISNODE,
+ mq_order);
+ if (page == NULL) {
+ dev_err(xpc_part, "xpc_create_gru_mq_uv() failed to alloc %d "
+ "bytes of memory on nid=%d for GRU mq\n", mq_size, nid);
+ return NULL;
+ }
+
+ mq = page_address(page);
+ ret = gru_create_message_queue(mq, mq_size);
+ if (ret != 0) {
+ dev_err(xpc_part, "gru_create_message_queue() returned "
+ "error=%d\n", ret);
+ free_pages((unsigned long)mq, mq_order);
+ return NULL;
+ }
+
+ /* !!! Need to do some other things to set up IRQ */
+
+ ret = request_irq(irq, irq_handler, 0, "xpc", NULL);
+ if (ret != 0) {
+ dev_err(xpc_part, "request_irq(irq=%d) returned error=%d\n",
+ irq, ret);
+ free_pages((unsigned long)mq, mq_order);
+ return NULL;
+ }
+
+ /* !!! enable generation of irq when GRU mq op occurs to this mq */
+
+ /* ??? allow other partitions to access GRU mq? */
+
+ return mq;
+}
+
+static void
+xpc_destroy_gru_mq_uv(void *mq, unsigned int mq_size, unsigned int irq)
+{
+ /* ??? disallow other partitions to access GRU mq? */
+
+ /* !!! disable generation of irq when GRU mq op occurs to this mq */
+
+ free_irq(irq, NULL);
+
+ free_pages((unsigned long)mq, get_order(mq_size));
+}
+
+static enum xp_retval
+xpc_send_gru_msg(unsigned long mq_gpa, void *msg, size_t msg_size)
+{
+ enum xp_retval xp_ret;
+ int ret;
+
+ while (1) {
+ ret = gru_send_message_gpa(mq_gpa, msg, msg_size);
+ if (ret == MQE_OK) {
+ xp_ret = xpSuccess;
+ break;
+ }
+
+ if (ret == MQE_QUEUE_FULL) {
+ dev_dbg(xpc_chan, "gru_send_message_gpa() returned "
+ "error=MQE_QUEUE_FULL\n");
+ /* !!! handle QLimit reached; delay & try again */
+ /* ??? Do we add a limit to the number of retries? */
+ (void)msleep_interruptible(10);
+ } else if (ret == MQE_CONGESTION) {
+ dev_dbg(xpc_chan, "gru_send_message_gpa() returned "
+ "error=MQE_CONGESTION\n");
+ /* !!! handle LB Overflow; simply try again */
+ /* ??? Do we add a limit to the number of retries? */
+ } else {
+ /* !!! Currently this is MQE_UNEXPECTED_CB_ERR */
+ dev_err(xpc_chan, "gru_send_message_gpa() returned "
+ "error=%d\n", ret);
+ xp_ret = xpGruSendMqError;
+ break;
+ }
+ }
+ return xp_ret;
+}
+
+static void
+xpc_process_activate_IRQ_rcvd_uv(void)
+{
+ unsigned long irq_flags;
+ short partid;
+ struct xpc_partition *part;
+ u8 act_state_req;
+
+ DBUG_ON(xpc_activate_IRQ_rcvd == 0);
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ for (partid = 0; partid < XP_MAX_NPARTITIONS_UV; partid++) {
+ part = &xpc_partitions[partid];
+
+ if (part->sn.uv.act_state_req == 0)
+ continue;
+
+ xpc_activate_IRQ_rcvd--;
+ BUG_ON(xpc_activate_IRQ_rcvd < 0);
+
+ act_state_req = part->sn.uv.act_state_req;
+ part->sn.uv.act_state_req = 0;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ if (act_state_req == XPC_P_ASR_ACTIVATE_UV) {
+ if (part->act_state == XPC_P_AS_INACTIVE)
+ xpc_activate_partition(part);
+ else if (part->act_state == XPC_P_AS_DEACTIVATING)
+ XPC_DEACTIVATE_PARTITION(part, xpReactivating);
+
+ } else if (act_state_req == XPC_P_ASR_REACTIVATE_UV) {
+ if (part->act_state == XPC_P_AS_INACTIVE)
+ xpc_activate_partition(part);
+ else
+ XPC_DEACTIVATE_PARTITION(part, xpReactivating);
+
+ } else if (act_state_req == XPC_P_ASR_DEACTIVATE_UV) {
+ XPC_DEACTIVATE_PARTITION(part, part->sn.uv.reason);
+
+ } else {
+ BUG();
+ }
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (xpc_activate_IRQ_rcvd == 0)
+ break;
+ }
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+}
+
+static void
+xpc_handle_activate_mq_msg_uv(struct xpc_partition *part,
+ struct xpc_activate_mq_msghdr_uv *msg_hdr,
+ int *wakeup_hb_checker)
+{
+ unsigned long irq_flags;
+ struct xpc_partition_uv *part_uv = &part->sn.uv;
+ struct xpc_openclose_args *args;
+
+ part_uv->remote_act_state = msg_hdr->act_state;
+
+ switch (msg_hdr->type) {
+ case XPC_ACTIVATE_MQ_MSG_SYNC_ACT_STATE_UV:
+ /* syncing of remote_act_state was just done above */
+ break;
+
+ case XPC_ACTIVATE_MQ_MSG_INC_HEARTBEAT_UV: {
+ struct xpc_activate_mq_msg_heartbeat_req_uv *msg;
+
+ msg = container_of(msg_hdr,
+ struct xpc_activate_mq_msg_heartbeat_req_uv,
+ hdr);
+ part_uv->heartbeat = msg->heartbeat;
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_OFFLINE_HEARTBEAT_UV: {
+ struct xpc_activate_mq_msg_heartbeat_req_uv *msg;
+
+ msg = container_of(msg_hdr,
+ struct xpc_activate_mq_msg_heartbeat_req_uv,
+ hdr);
+ part_uv->heartbeat = msg->heartbeat;
+
+ spin_lock_irqsave(&part_uv->flags_lock, irq_flags);
+ part_uv->flags |= XPC_P_HEARTBEAT_OFFLINE_UV;
+ spin_unlock_irqrestore(&part_uv->flags_lock, irq_flags);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_ONLINE_HEARTBEAT_UV: {
+ struct xpc_activate_mq_msg_heartbeat_req_uv *msg;
+
+ msg = container_of(msg_hdr,
+ struct xpc_activate_mq_msg_heartbeat_req_uv,
+ hdr);
+ part_uv->heartbeat = msg->heartbeat;
+
+ spin_lock_irqsave(&part_uv->flags_lock, irq_flags);
+ part_uv->flags &= ~XPC_P_HEARTBEAT_OFFLINE_UV;
+ spin_unlock_irqrestore(&part_uv->flags_lock, irq_flags);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_ACTIVATE_REQ_UV: {
+ struct xpc_activate_mq_msg_activate_req_uv *msg;
+
+ /*
+ * ??? Do we deal here with ts_jiffies being different
+ * ??? if act_state != XPC_P_AS_INACTIVE instead of
+ * ??? below?
+ */
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_activate_req_uv, hdr);
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = XPC_P_ASR_ACTIVATE_UV;
+ part->remote_rp_pa = msg->rp_gpa; /* !!! _pa is _gpa */
+ part->remote_rp_ts_jiffies = msg_hdr->rp_ts_jiffies;
+ part_uv->remote_activate_mq_gpa = msg->activate_mq_gpa;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ (*wakeup_hb_checker)++;
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_DEACTIVATE_REQ_UV: {
+ struct xpc_activate_mq_msg_deactivate_req_uv *msg;
+
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_deactivate_req_uv, hdr);
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = XPC_P_ASR_DEACTIVATE_UV;
+ part_uv->reason = msg->reason;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ (*wakeup_hb_checker)++;
+ return;
+ }
+ case XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREQUEST_UV: {
+ struct xpc_activate_mq_msg_chctl_closerequest_uv *msg;
+
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_chctl_closerequest_uv,
+ hdr);
+ args = &part->remote_openclose_args[msg->ch_number];
+ args->reason = msg->reason;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.flags[msg->ch_number] |= XPC_CHCTL_CLOSEREQUEST;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ xpc_wakeup_channel_mgr(part);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREPLY_UV: {
+ struct xpc_activate_mq_msg_chctl_closereply_uv *msg;
+
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_chctl_closereply_uv,
+ hdr);
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.flags[msg->ch_number] |= XPC_CHCTL_CLOSEREPLY;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ xpc_wakeup_channel_mgr(part);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREQUEST_UV: {
+ struct xpc_activate_mq_msg_chctl_openrequest_uv *msg;
+
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_chctl_openrequest_uv,
+ hdr);
+ args = &part->remote_openclose_args[msg->ch_number];
+ args->entry_size = msg->entry_size;
+ args->local_nentries = msg->local_nentries;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.flags[msg->ch_number] |= XPC_CHCTL_OPENREQUEST;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ xpc_wakeup_channel_mgr(part);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREPLY_UV: {
+ struct xpc_activate_mq_msg_chctl_openreply_uv *msg;
+
+ msg = container_of(msg_hdr, struct
+ xpc_activate_mq_msg_chctl_openreply_uv, hdr);
+ args = &part->remote_openclose_args[msg->ch_number];
+ args->remote_nentries = msg->remote_nentries;
+ args->local_nentries = msg->local_nentries;
+ args->local_msgqueue_pa = msg->local_notify_mq_gpa;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.flags[msg->ch_number] |= XPC_CHCTL_OPENREPLY;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ xpc_wakeup_channel_mgr(part);
+ break;
+ }
+ case XPC_ACTIVATE_MQ_MSG_MARK_ENGAGED_UV:
+ spin_lock_irqsave(&part_uv->flags_lock, irq_flags);
+ part_uv->flags |= XPC_P_ENGAGED_UV;
+ spin_unlock_irqrestore(&part_uv->flags_lock, irq_flags);
+ break;
+
+ case XPC_ACTIVATE_MQ_MSG_MARK_DISENGAGED_UV:
+ spin_lock_irqsave(&part_uv->flags_lock, irq_flags);
+ part_uv->flags &= ~XPC_P_ENGAGED_UV;
+ spin_unlock_irqrestore(&part_uv->flags_lock, irq_flags);
+ break;
+
+ default:
+ dev_err(xpc_part, "received unknown activate_mq msg type=%d "
+ "from partition=%d\n", msg_hdr->type, XPC_PARTID(part));
+
+ /* get hb checker to deactivate from the remote partition */
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = XPC_P_ASR_DEACTIVATE_UV;
+ part_uv->reason = xpBadMsgType;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ (*wakeup_hb_checker)++;
+ return;
+ }
+
+ if (msg_hdr->rp_ts_jiffies != part->remote_rp_ts_jiffies &&
+ part->remote_rp_ts_jiffies != 0) {
+ /*
+ * ??? Does what we do here need to be sensitive to
+ * ??? act_state or remote_act_state?
+ */
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = XPC_P_ASR_REACTIVATE_UV;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ (*wakeup_hb_checker)++;
+ }
+}
+
+static irqreturn_t
+xpc_handle_activate_IRQ_uv(int irq, void *dev_id)
+{
+ struct xpc_activate_mq_msghdr_uv *msg_hdr;
+ short partid;
+ struct xpc_partition *part;
+ int wakeup_hb_checker = 0;
+
+ while ((msg_hdr = gru_get_next_message(xpc_activate_mq_uv)) != NULL) {
+
+ partid = msg_hdr->partid;
+ if (partid < 0 || partid >= XP_MAX_NPARTITIONS_UV) {
+ dev_err(xpc_part, "xpc_handle_activate_IRQ_uv() "
+ "received invalid partid=0x%x in message\n",
+ partid);
+ } else {
+ part = &xpc_partitions[partid];
+ if (xpc_part_ref(part)) {
+ xpc_handle_activate_mq_msg_uv(part, msg_hdr,
+ &wakeup_hb_checker);
+ xpc_part_deref(part);
+ }
+ }
+
+ gru_free_message(xpc_activate_mq_uv, msg_hdr);
+ }
+
+ if (wakeup_hb_checker)
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
+
+ return IRQ_HANDLED;
+}
+
+static enum xp_retval
+xpc_send_activate_IRQ_uv(struct xpc_partition *part, void *msg, size_t msg_size,
+ int msg_type)
+{
+ struct xpc_activate_mq_msghdr_uv *msg_hdr = msg;
+
+ DBUG_ON(msg_size > XPC_ACTIVATE_MSG_SIZE_UV);
+
+ msg_hdr->type = msg_type;
+ msg_hdr->partid = XPC_PARTID(part);
+ msg_hdr->act_state = part->act_state;
+ msg_hdr->rp_ts_jiffies = xpc_rsvd_page->ts_jiffies;
+
+ /* ??? Is holding a spin_lock (ch->lock) during this call a bad idea? */
+ return xpc_send_gru_msg(part->sn.uv.remote_activate_mq_gpa, msg,
+ msg_size);
+}
+
+static void
+xpc_send_activate_IRQ_part_uv(struct xpc_partition *part, void *msg,
+ size_t msg_size, int msg_type)
+{
+ enum xp_retval ret;
+
+ ret = xpc_send_activate_IRQ_uv(part, msg, msg_size, msg_type);
+ if (unlikely(ret != xpSuccess))
+ XPC_DEACTIVATE_PARTITION(part, ret);
+}
+
+static void
+xpc_send_activate_IRQ_ch_uv(struct xpc_channel *ch, unsigned long *irq_flags,
+ void *msg, size_t msg_size, int msg_type)
+{
+ struct xpc_partition *part = &xpc_partitions[ch->number];
+ enum xp_retval ret;
+
+ ret = xpc_send_activate_IRQ_uv(part, msg, msg_size, msg_type);
+ if (unlikely(ret != xpSuccess)) {
+ if (irq_flags != NULL)
+ spin_unlock_irqrestore(&ch->lock, *irq_flags);
+
+ XPC_DEACTIVATE_PARTITION(part, ret);
+
+ if (irq_flags != NULL)
+ spin_lock_irqsave(&ch->lock, *irq_flags);
+ }
+}
+
+static void
+xpc_send_local_activate_IRQ_uv(struct xpc_partition *part, int act_state_req)
+{
+ unsigned long irq_flags;
+ struct xpc_partition_uv *part_uv = &part->sn.uv;
+
+ /*
+ * !!! Make our side think that the remote parition sent an activate
+ * !!! message our way by doing what the activate IRQ handler would
+ * !!! do had one really been sent.
+ */
+
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = act_state_req;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
+}
+
+static enum xp_retval
+xpc_get_partition_rsvd_page_pa_uv(void *buf, u64 *cookie, unsigned long *rp_pa,
+ size_t *len)
+{
+ /* !!! call the UV version of sn_partition_reserved_page_pa() */
+ return xpUnsupported;
+}
+
+static int
+xpc_setup_rsvd_page_sn_uv(struct xpc_rsvd_page *rp)
+{
+ rp->sn.activate_mq_gpa = uv_gpa(xpc_activate_mq_uv);
+ return 0;
+}
+
+static void
+xpc_send_heartbeat_uv(int msg_type)
+{
+ short partid;
+ struct xpc_partition *part;
+ struct xpc_activate_mq_msg_heartbeat_req_uv msg;
+
+ /*
+ * !!! On uv we're broadcasting a heartbeat message every 5 seconds.
+ * !!! Whereas on sn2 we're bte_copy'ng the heartbeat info every 20
+ * !!! seconds. This is an increase in numalink traffic.
+ * ??? Is this good?
+ */
+
+ msg.heartbeat = atomic64_inc_return(&xpc_heartbeat_uv);
+
+ partid = find_first_bit(xpc_heartbeating_to_mask_uv,
+ XP_MAX_NPARTITIONS_UV);
+
+ while (partid < XP_MAX_NPARTITIONS_UV) {
+ part = &xpc_partitions[partid];
+
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ msg_type);
+
+ partid = find_next_bit(xpc_heartbeating_to_mask_uv,
+ XP_MAX_NPARTITIONS_UV, partid + 1);
+ }
+}
+
+static void
+xpc_increment_heartbeat_uv(void)
+{
+ xpc_send_heartbeat_uv(XPC_ACTIVATE_MQ_MSG_INC_HEARTBEAT_UV);
+}
+
+static void
+xpc_offline_heartbeat_uv(void)
+{
+ xpc_send_heartbeat_uv(XPC_ACTIVATE_MQ_MSG_OFFLINE_HEARTBEAT_UV);
+}
+
+static void
+xpc_online_heartbeat_uv(void)
+{
+ xpc_send_heartbeat_uv(XPC_ACTIVATE_MQ_MSG_ONLINE_HEARTBEAT_UV);
+}
+
+static void
+xpc_heartbeat_init_uv(void)
+{
+ atomic64_set(&xpc_heartbeat_uv, 0);
+ bitmap_zero(xpc_heartbeating_to_mask_uv, XP_MAX_NPARTITIONS_UV);
+ xpc_heartbeating_to_mask = &xpc_heartbeating_to_mask_uv[0];
+}
+
+static void
+xpc_heartbeat_exit_uv(void)
+{
+ xpc_send_heartbeat_uv(XPC_ACTIVATE_MQ_MSG_OFFLINE_HEARTBEAT_UV);
+}
+
+static enum xp_retval
+xpc_get_remote_heartbeat_uv(struct xpc_partition *part)
+{
+ struct xpc_partition_uv *part_uv = &part->sn.uv;
+ enum xp_retval ret = xpNoHeartbeat;
+
+ if (part_uv->remote_act_state != XPC_P_AS_INACTIVE &&
+ part_uv->remote_act_state != XPC_P_AS_DEACTIVATING) {
+
+ if (part_uv->heartbeat != part->last_heartbeat ||
+ (part_uv->flags & XPC_P_HEARTBEAT_OFFLINE_UV)) {
+
+ part->last_heartbeat = part_uv->heartbeat;
+ ret = xpSuccess;
+ }
+ }
+ return ret;
+}
+
+static void
+xpc_request_partition_activation_uv(struct xpc_rsvd_page *remote_rp,
+ unsigned long remote_rp_gpa, int nasid)
+{
+ short partid = remote_rp->SAL_partid;
+ struct xpc_partition *part = &xpc_partitions[partid];
+ struct xpc_activate_mq_msg_activate_req_uv msg;
+
+ part->remote_rp_pa = remote_rp_gpa; /* !!! _pa here is really _gpa */
+ part->remote_rp_ts_jiffies = remote_rp->ts_jiffies;
+ part->sn.uv.remote_activate_mq_gpa = remote_rp->sn.activate_mq_gpa;
+
+ /*
+ * ??? Is it a good idea to make this conditional on what is
+ * ??? potentially stale state information?
+ */
+ if (part->sn.uv.remote_act_state == XPC_P_AS_INACTIVE) {
+ msg.rp_gpa = uv_gpa(xpc_rsvd_page);
+ msg.activate_mq_gpa = xpc_rsvd_page->sn.activate_mq_gpa;
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_ACTIVATE_REQ_UV);
+ }
+
+ if (part->act_state == XPC_P_AS_INACTIVE)
+ xpc_send_local_activate_IRQ_uv(part, XPC_P_ASR_ACTIVATE_UV);
+}
+
+static void
+xpc_request_partition_reactivation_uv(struct xpc_partition *part)
+{
+ xpc_send_local_activate_IRQ_uv(part, XPC_P_ASR_ACTIVATE_UV);
+}
+
+static void
+xpc_request_partition_deactivation_uv(struct xpc_partition *part)
+{
+ struct xpc_activate_mq_msg_deactivate_req_uv msg;
+
+ /*
+ * ??? Is it a good idea to make this conditional on what is
+ * ??? potentially stale state information?
+ */
+ if (part->sn.uv.remote_act_state != XPC_P_AS_DEACTIVATING &&
+ part->sn.uv.remote_act_state != XPC_P_AS_INACTIVE) {
+
+ msg.reason = part->reason;
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_DEACTIVATE_REQ_UV);
+ }
+}
+
+static void
+xpc_cancel_partition_deactivation_request_uv(struct xpc_partition *part)
+{
+ /* nothing needs to be done */
+ return;
+}
+
+static void
+xpc_init_fifo_uv(struct xpc_fifo_head_uv *head)
+{
+ head->first = NULL;
+ head->last = NULL;
+ spin_lock_init(&head->lock);
+ head->n_entries = 0;
+}
+
+static void *
+xpc_get_fifo_entry_uv(struct xpc_fifo_head_uv *head)
+{
+ unsigned long irq_flags;
+ struct xpc_fifo_entry_uv *first;
+
+ spin_lock_irqsave(&head->lock, irq_flags);
+ first = head->first;
+ if (head->first != NULL) {
+ head->first = first->next;
+ if (head->first == NULL)
+ head->last = NULL;
+ }
+ head->n_entries++;
+ spin_unlock_irqrestore(&head->lock, irq_flags);
+ first->next = NULL;
+ return first;
+}
+
+static void
+xpc_put_fifo_entry_uv(struct xpc_fifo_head_uv *head,
+ struct xpc_fifo_entry_uv *last)
+{
+ unsigned long irq_flags;
+
+ last->next = NULL;
+ spin_lock_irqsave(&head->lock, irq_flags);
+ if (head->last != NULL)
+ head->last->next = last;
+ else
+ head->first = last;
+ head->last = last;
+ head->n_entries--;
+ BUG_ON(head->n_entries < 0);
+ spin_unlock_irqrestore(&head->lock, irq_flags);
+}
+
+static int
+xpc_n_of_fifo_entries_uv(struct xpc_fifo_head_uv *head)
+{
+ return head->n_entries;
+}
+
+/*
+ * Setup the channel structures that are uv specific.
+ */
+static enum xp_retval
+xpc_setup_ch_structures_sn_uv(struct xpc_partition *part)
+{
+ struct xpc_channel_uv *ch_uv;
+ int ch_number;
+
+ for (ch_number = 0; ch_number < part->nchannels; ch_number++) {
+ ch_uv = &part->channels[ch_number].sn.uv;
+
+ xpc_init_fifo_uv(&ch_uv->msg_slot_free_list);
+ xpc_init_fifo_uv(&ch_uv->recv_msg_list);
+ }
+
+ return xpSuccess;
+}
+
+/*
+ * Teardown the channel structures that are uv specific.
+ */
+static void
+xpc_teardown_ch_structures_sn_uv(struct xpc_partition *part)
+{
+ /* nothing needs to be done */
+ return;
+}
+
+static enum xp_retval
+xpc_make_first_contact_uv(struct xpc_partition *part)
+{
+ struct xpc_activate_mq_msg_uv msg;
+
+ /*
+ * We send a sync msg to get the remote partition's remote_act_state
+ * updated to our current act_state which at this point should
+ * be XPC_P_AS_ACTIVATING.
+ */
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_SYNC_ACT_STATE_UV);
+
+ while (part->sn.uv.remote_act_state != XPC_P_AS_ACTIVATING) {
+
+ dev_dbg(xpc_part, "waiting to make first contact with "
+ "partition %d\n", XPC_PARTID(part));
+
+ /* wait a 1/4 of a second or so */
+ (void)msleep_interruptible(250);
+
+ if (part->act_state == XPC_P_AS_DEACTIVATING)
+ return part->reason;
+ }
+
+ return xpSuccess;
+}
+
+static u64
+xpc_get_chctl_all_flags_uv(struct xpc_partition *part)
+{
+ unsigned long irq_flags;
+ union xpc_channel_ctl_flags chctl;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ chctl = part->chctl;
+ if (chctl.all_flags != 0)
+ part->chctl.all_flags = 0;
+
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+ return chctl.all_flags;
+}
+
+static enum xp_retval
+xpc_allocate_send_msg_slot_uv(struct xpc_channel *ch)
+{
+ struct xpc_channel_uv *ch_uv = &ch->sn.uv;
+ struct xpc_send_msg_slot_uv *msg_slot;
+ unsigned long irq_flags;
+ int nentries;
+ int entry;
+ size_t nbytes;
+
+ for (nentries = ch->local_nentries; nentries > 0; nentries--) {
+ nbytes = nentries * sizeof(struct xpc_send_msg_slot_uv);
+ ch_uv->send_msg_slots = kzalloc(nbytes, GFP_KERNEL);
+ if (ch_uv->send_msg_slots == NULL)
+ continue;
+
+ for (entry = 0; entry < nentries; entry++) {
+ msg_slot = &ch_uv->send_msg_slots[entry];
+
+ msg_slot->msg_slot_number = entry;
+ xpc_put_fifo_entry_uv(&ch_uv->msg_slot_free_list,
+ &msg_slot->next);
+ }
+
+ spin_lock_irqsave(&ch->lock, irq_flags);
+ if (nentries < ch->local_nentries)
+ ch->local_nentries = nentries;
+ spin_unlock_irqrestore(&ch->lock, irq_flags);
+ return xpSuccess;
+ }
+
+ return xpNoMemory;
+}
+
+static enum xp_retval
+xpc_allocate_recv_msg_slot_uv(struct xpc_channel *ch)
+{
+ struct xpc_channel_uv *ch_uv = &ch->sn.uv;
+ struct xpc_notify_mq_msg_uv *msg_slot;
+ unsigned long irq_flags;
+ int nentries;
+ int entry;
+ size_t nbytes;
+
+ for (nentries = ch->remote_nentries; nentries > 0; nentries--) {
+ nbytes = nentries * ch->entry_size;
+ ch_uv->recv_msg_slots = kzalloc(nbytes, GFP_KERNEL);
+ if (ch_uv->recv_msg_slots == NULL)
+ continue;
+
+ for (entry = 0; entry < nentries; entry++) {
+ msg_slot = ch_uv->recv_msg_slots + entry *
+ ch->entry_size;
+
+ msg_slot->hdr.msg_slot_number = entry;
+ }
+
+ spin_lock_irqsave(&ch->lock, irq_flags);
+ if (nentries < ch->remote_nentries)
+ ch->remote_nentries = nentries;
+ spin_unlock_irqrestore(&ch->lock, irq_flags);
+ return xpSuccess;
+ }
+
+ return xpNoMemory;
+}
+
+/*
+ * Allocate msg_slots associated with the channel.
+ */
+static enum xp_retval
+xpc_setup_msg_structures_uv(struct xpc_channel *ch)
+{
+ static enum xp_retval ret;
+ struct xpc_channel_uv *ch_uv = &ch->sn.uv;
+
+ DBUG_ON(ch->flags & XPC_C_SETUP);
+
+ ret = xpc_allocate_send_msg_slot_uv(ch);
+ if (ret == xpSuccess) {
+
+ ret = xpc_allocate_recv_msg_slot_uv(ch);
+ if (ret != xpSuccess) {
+ kfree(ch_uv->send_msg_slots);
+ xpc_init_fifo_uv(&ch_uv->msg_slot_free_list);
+ }
+ }
+ return ret;
+}
+
+/*
+ * Free up msg_slots and clear other stuff that were setup for the specified
+ * channel.
+ */
+static void
+xpc_teardown_msg_structures_uv(struct xpc_channel *ch)
+{
+ struct xpc_channel_uv *ch_uv = &ch->sn.uv;
+
+ DBUG_ON(!spin_is_locked(&ch->lock));
+
+ ch_uv->remote_notify_mq_gpa = 0;
+
+ if (ch->flags & XPC_C_SETUP) {
+ xpc_init_fifo_uv(&ch_uv->msg_slot_free_list);
+ kfree(ch_uv->send_msg_slots);
+ xpc_init_fifo_uv(&ch_uv->recv_msg_list);
+ kfree(ch_uv->recv_msg_slots);
+ }
+}
+
+static void
+xpc_send_chctl_closerequest_uv(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_activate_mq_msg_chctl_closerequest_uv msg;
+
+ msg.ch_number = ch->number;
+ msg.reason = ch->reason;
+ xpc_send_activate_IRQ_ch_uv(ch, irq_flags, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREQUEST_UV);
+}
+
+static void
+xpc_send_chctl_closereply_uv(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_activate_mq_msg_chctl_closereply_uv msg;
+
+ msg.ch_number = ch->number;
+ xpc_send_activate_IRQ_ch_uv(ch, irq_flags, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_CHCTL_CLOSEREPLY_UV);
+}
+
+static void
+xpc_send_chctl_openrequest_uv(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_activate_mq_msg_chctl_openrequest_uv msg;
+
+ msg.ch_number = ch->number;
+ msg.entry_size = ch->entry_size;
+ msg.local_nentries = ch->local_nentries;
+ xpc_send_activate_IRQ_ch_uv(ch, irq_flags, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREQUEST_UV);
+}
+
+static void
+xpc_send_chctl_openreply_uv(struct xpc_channel *ch, unsigned long *irq_flags)
+{
+ struct xpc_activate_mq_msg_chctl_openreply_uv msg;
+
+ msg.ch_number = ch->number;
+ msg.local_nentries = ch->local_nentries;
+ msg.remote_nentries = ch->remote_nentries;
+ msg.local_notify_mq_gpa = uv_gpa(xpc_notify_mq_uv);
+ xpc_send_activate_IRQ_ch_uv(ch, irq_flags, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_CHCTL_OPENREPLY_UV);
+}
+
+static void
+xpc_send_chctl_local_msgrequest_uv(struct xpc_partition *part, int ch_number)
+{
+ unsigned long irq_flags;
+
+ spin_lock_irqsave(&part->chctl_lock, irq_flags);
+ part->chctl.flags[ch_number] |= XPC_CHCTL_MSGREQUEST;
+ spin_unlock_irqrestore(&part->chctl_lock, irq_flags);
+
+ xpc_wakeup_channel_mgr(part);
+}
+
+static void
+xpc_save_remote_msgqueue_pa_uv(struct xpc_channel *ch,
+ unsigned long msgqueue_pa)
+{
+ ch->sn.uv.remote_notify_mq_gpa = msgqueue_pa;
+}
+
+static void
+xpc_indicate_partition_engaged_uv(struct xpc_partition *part)
+{
+ struct xpc_activate_mq_msg_uv msg;
+
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_MARK_ENGAGED_UV);
+}
+
+static void
+xpc_indicate_partition_disengaged_uv(struct xpc_partition *part)
+{
+ struct xpc_activate_mq_msg_uv msg;
+
+ xpc_send_activate_IRQ_part_uv(part, &msg, sizeof(msg),
+ XPC_ACTIVATE_MQ_MSG_MARK_DISENGAGED_UV);
+}
+
+static void
+xpc_assume_partition_disengaged_uv(short partid)
+{
+ struct xpc_partition_uv *part_uv = &xpc_partitions[partid].sn.uv;
+ unsigned long irq_flags;
+
+ spin_lock_irqsave(&part_uv->flags_lock, irq_flags);
+ part_uv->flags &= ~XPC_P_ENGAGED_UV;
+ spin_unlock_irqrestore(&part_uv->flags_lock, irq_flags);
+}
+
+static int
+xpc_partition_engaged_uv(short partid)
+{
+ return (xpc_partitions[partid].sn.uv.flags & XPC_P_ENGAGED_UV) != 0;
+}
+
+static int
+xpc_any_partition_engaged_uv(void)
+{
+ struct xpc_partition_uv *part_uv;
+ short partid;
+
+ for (partid = 0; partid < XP_MAX_NPARTITIONS_UV; partid++) {
+ part_uv = &xpc_partitions[partid].sn.uv;
+ if ((part_uv->flags & XPC_P_ENGAGED_UV) != 0)
+ return 1;
+ }
+ return 0;
+}
+
+static enum xp_retval
+xpc_allocate_msg_slot_uv(struct xpc_channel *ch, u32 flags,
+ struct xpc_send_msg_slot_uv **address_of_msg_slot)
+{
+ enum xp_retval ret;
+ struct xpc_send_msg_slot_uv *msg_slot;
+ struct xpc_fifo_entry_uv *entry;
+
+ while (1) {
+ entry = xpc_get_fifo_entry_uv(&ch->sn.uv.msg_slot_free_list);
+ if (entry != NULL)
+ break;
+
+ if (flags & XPC_NOWAIT)
+ return xpNoWait;
+
+ ret = xpc_allocate_msg_wait(ch);
+ if (ret != xpInterrupted && ret != xpTimeout)
+ return ret;
+ }
+
+ msg_slot = container_of(entry, struct xpc_send_msg_slot_uv, next);
+ *address_of_msg_slot = msg_slot;
+ return xpSuccess;
+}
+
+static void
+xpc_free_msg_slot_uv(struct xpc_channel *ch,
+ struct xpc_send_msg_slot_uv *msg_slot)
+{
+ xpc_put_fifo_entry_uv(&ch->sn.uv.msg_slot_free_list, &msg_slot->next);
+
+ /* wakeup anyone waiting for a free msg slot */
+ if (atomic_read(&ch->n_on_msg_allocate_wq) > 0)
+ wake_up(&ch->msg_allocate_wq);
+}
+
+static void
+xpc_notify_sender_uv(struct xpc_channel *ch,
+ struct xpc_send_msg_slot_uv *msg_slot,
+ enum xp_retval reason)
+{
+ xpc_notify_func func = msg_slot->func;
+
+ if (func != NULL && cmpxchg(&msg_slot->func, func, NULL) == func) {
+
+ atomic_dec(&ch->n_to_notify);
+
+ dev_dbg(xpc_chan, "msg_slot->func() called, msg_slot=0x%p "
+ "msg_slot_number=%d partid=%d channel=%d\n", msg_slot,
+ msg_slot->msg_slot_number, ch->partid, ch->number);
+
+ func(reason, ch->partid, ch->number, msg_slot->key);
+
+ dev_dbg(xpc_chan, "msg_slot->func() returned, msg_slot=0x%p "
+ "msg_slot_number=%d partid=%d channel=%d\n", msg_slot,
+ msg_slot->msg_slot_number, ch->partid, ch->number);
+ }
+}
+
+static void
+xpc_handle_notify_mq_ack_uv(struct xpc_channel *ch,
+ struct xpc_notify_mq_msg_uv *msg)
+{
+ struct xpc_send_msg_slot_uv *msg_slot;
+ int entry = msg->hdr.msg_slot_number % ch->local_nentries;
+
+ msg_slot = &ch->sn.uv.send_msg_slots[entry];
+
+ BUG_ON(msg_slot->msg_slot_number != msg->hdr.msg_slot_number);
+ msg_slot->msg_slot_number += ch->local_nentries;
+
+ if (msg_slot->func != NULL)
+ xpc_notify_sender_uv(ch, msg_slot, xpMsgDelivered);
+
+ xpc_free_msg_slot_uv(ch, msg_slot);
+}
+
+static void
+xpc_handle_notify_mq_msg_uv(struct xpc_partition *part,
+ struct xpc_notify_mq_msg_uv *msg)
+{
+ struct xpc_partition_uv *part_uv = &part->sn.uv;
+ struct xpc_channel *ch;
+ struct xpc_channel_uv *ch_uv;
+ struct xpc_notify_mq_msg_uv *msg_slot;
+ unsigned long irq_flags;
+ int ch_number = msg->hdr.ch_number;
+
+ if (unlikely(ch_number >= part->nchannels)) {
+ dev_err(xpc_part, "xpc_handle_notify_IRQ_uv() received invalid "
+ "channel number=0x%x in message from partid=%d\n",
+ ch_number, XPC_PARTID(part));
+
+ /* get hb checker to deactivate from the remote partition */
+ spin_lock_irqsave(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+ if (part_uv->act_state_req == 0)
+ xpc_activate_IRQ_rcvd++;
+ part_uv->act_state_req = XPC_P_ASR_DEACTIVATE_UV;
+ part_uv->reason = xpBadChannelNumber;
+ spin_unlock_irqrestore(&xpc_activate_IRQ_rcvd_lock, irq_flags);
+
+ wake_up_interruptible(&xpc_activate_IRQ_wq);
+ return;
+ }
+
+ ch = &part->channels[ch_number];
+ xpc_msgqueue_ref(ch);
+
+ if (!(ch->flags & XPC_C_CONNECTED)) {
+ xpc_msgqueue_deref(ch);
+ return;
+ }
+
+ /* see if we're really dealing with an ACK for a previously sent msg */
+ if (msg->hdr.size == 0) {
+ xpc_handle_notify_mq_ack_uv(ch, msg);
+ xpc_msgqueue_deref(ch);
+ return;
+ }
+
+ /* we're dealing with a normal message sent via the notify_mq */
+ ch_uv = &ch->sn.uv;
+
+ msg_slot = (struct xpc_notify_mq_msg_uv *)((u64)ch_uv->recv_msg_slots +
+ (msg->hdr.msg_slot_number % ch->remote_nentries) *
+ ch->entry_size);
+
+ BUG_ON(msg->hdr.msg_slot_number != msg_slot->hdr.msg_slot_number);
+ BUG_ON(msg_slot->hdr.size != 0);
+
+ memcpy(msg_slot, msg, msg->hdr.size);
+
+ xpc_put_fifo_entry_uv(&ch_uv->recv_msg_list, &msg_slot->hdr.u.next);
+
+ if (ch->flags & XPC_C_CONNECTEDCALLOUT_MADE) {
+ /*
+ * If there is an existing idle kthread get it to deliver
+ * the payload, otherwise we'll have to get the channel mgr
+ * for this partition to create a kthread to do the delivery.
+ */
+ if (atomic_read(&ch->kthreads_idle) > 0)
+ wake_up_nr(&ch->idle_wq, 1);
+ else
+ xpc_send_chctl_local_msgrequest_uv(part, ch->number);
+ }
+ xpc_msgqueue_deref(ch);
+}
+
+static irqreturn_t
+xpc_handle_notify_IRQ_uv(int irq, void *dev_id)
+{
+ struct xpc_notify_mq_msg_uv *msg;
+ short partid;
+ struct xpc_partition *part;
+
+ while ((msg = gru_get_next_message(xpc_notify_mq_uv)) != NULL) {
+
+ partid = msg->hdr.partid;
+ if (partid < 0 || partid >= XP_MAX_NPARTITIONS_UV) {
+ dev_err(xpc_part, "xpc_handle_notify_IRQ_uv() received "
+ "invalid partid=0x%x in message\n", partid);
+ } else {
+ part = &xpc_partitions[partid];
+
+ if (xpc_part_ref(part)) {
+ xpc_handle_notify_mq_msg_uv(part, msg);
+ xpc_part_deref(part);
+ }
+ }
+
+ gru_free_message(xpc_notify_mq_uv, msg);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int
+xpc_n_of_deliverable_payloads_uv(struct xpc_channel *ch)
+{
+ return xpc_n_of_fifo_entries_uv(&ch->sn.uv.recv_msg_list);
+}
+
+static void
+xpc_process_msg_chctl_flags_uv(struct xpc_partition *part, int ch_number)
+{
+ struct xpc_channel *ch = &part->channels[ch_number];
+ int ndeliverable_payloads;
+
+ xpc_msgqueue_ref(ch);
+
+ ndeliverable_payloads = xpc_n_of_deliverable_payloads_uv(ch);
+
+ if (ndeliverable_payloads > 0 &&
+ (ch->flags & XPC_C_CONNECTED) &&
+ (ch->flags & XPC_C_CONNECTEDCALLOUT_MADE)) {
+
+ xpc_activate_kthreads(ch, ndeliverable_payloads);
+ }
+
+ xpc_msgqueue_deref(ch);
+}
+
+static enum xp_retval
+xpc_send_payload_uv(struct xpc_channel *ch, u32 flags, void *payload,
+ u16 payload_size, u8 notify_type, xpc_notify_func func,
+ void *key)
+{
+ enum xp_retval ret = xpSuccess;
+ struct xpc_send_msg_slot_uv *msg_slot = NULL;
+ struct xpc_notify_mq_msg_uv *msg;
+ u8 msg_buffer[XPC_NOTIFY_MSG_SIZE_UV];
+ size_t msg_size;
+
+ DBUG_ON(notify_type != XPC_N_CALL);
+
+ msg_size = sizeof(struct xpc_notify_mq_msghdr_uv) + payload_size;
+ if (msg_size > ch->entry_size)
+ return xpPayloadTooBig;
+
+ xpc_msgqueue_ref(ch);
+
+ if (ch->flags & XPC_C_DISCONNECTING) {
+ ret = ch->reason;
+ goto out_1;
+ }
+ if (!(ch->flags & XPC_C_CONNECTED)) {
+ ret = xpNotConnected;
+ goto out_1;
+ }
+
+ ret = xpc_allocate_msg_slot_uv(ch, flags, &msg_slot);
+ if (ret != xpSuccess)
+ goto out_1;
+
+ if (func != NULL) {
+ atomic_inc(&ch->n_to_notify);
+
+ msg_slot->key = key;
+ wmb(); /* a non-NULL func must hit memory after the key */
+ msg_slot->func = func;
+
+ if (ch->flags & XPC_C_DISCONNECTING) {
+ ret = ch->reason;
+ goto out_2;
+ }
+ }
+
+ msg = (struct xpc_notify_mq_msg_uv *)&msg_buffer;
+ msg->hdr.partid = xp_partition_id;
+ msg->hdr.ch_number = ch->number;
+ msg->hdr.size = msg_size;
+ msg->hdr.msg_slot_number = msg_slot->msg_slot_number;
+ memcpy(&msg->payload, payload, payload_size);
+
+ ret = xpc_send_gru_msg(ch->sn.uv.remote_notify_mq_gpa, msg, msg_size);
+ if (ret == xpSuccess)
+ goto out_1;
+
+ XPC_DEACTIVATE_PARTITION(&xpc_partitions[ch->partid], ret);
+out_2:
+ if (func != NULL) {
+ /*
+ * Try to NULL the msg_slot's func field. If we fail, then
+ * xpc_notify_senders_of_disconnect_uv() beat us to it, in which
+ * case we need to pretend we succeeded to send the message
+ * since the user will get a callout for the disconnect error
+ * by xpc_notify_senders_of_disconnect_uv(), and to also get an
+ * error returned here will confuse them. Additionally, since
+ * in this case the channel is being disconnected we don't need
+ * to put the the msg_slot back on the free list.
+ */
+ if (cmpxchg(&msg_slot->func, func, NULL) != func) {
+ ret = xpSuccess;
+ goto out_1;
+ }
+
+ msg_slot->key = NULL;
+ atomic_dec(&ch->n_to_notify);
+ }
+ xpc_free_msg_slot_uv(ch, msg_slot);
+out_1:
+ xpc_msgqueue_deref(ch);
+ return ret;
+}
+
+/*
+ * Tell the callers of xpc_send_notify() that the status of their payloads
+ * is unknown because the channel is now disconnecting.
+ *
+ * We don't worry about putting these msg_slots on the free list since the
+ * msg_slots themselves are about to be kfree'd.
+ */
+static void
+xpc_notify_senders_of_disconnect_uv(struct xpc_channel *ch)
+{
+ struct xpc_send_msg_slot_uv *msg_slot;
+ int entry;
+
+ DBUG_ON(!(ch->flags & XPC_C_DISCONNECTING));
+
+ for (entry = 0; entry < ch->local_nentries; entry++) {
+
+ if (atomic_read(&ch->n_to_notify) == 0)
+ break;
+
+ msg_slot = &ch->sn.uv.send_msg_slots[entry];
+ if (msg_slot->func != NULL)
+ xpc_notify_sender_uv(ch, msg_slot, ch->reason);
+ }
+}
+
+/*
+ * Get the next deliverable message's payload.
+ */
+static void *
+xpc_get_deliverable_payload_uv(struct xpc_channel *ch)
+{
+ struct xpc_fifo_entry_uv *entry;
+ struct xpc_notify_mq_msg_uv *msg;
+ void *payload = NULL;
+
+ if (!(ch->flags & XPC_C_DISCONNECTING)) {
+ entry = xpc_get_fifo_entry_uv(&ch->sn.uv.recv_msg_list);
+ if (entry != NULL) {
+ msg = container_of(entry, struct xpc_notify_mq_msg_uv,
+ hdr.u.next);
+ payload = &msg->payload;
+ }
+ }
+ return payload;
+}
+
+static void
+xpc_received_payload_uv(struct xpc_channel *ch, void *payload)
+{
+ struct xpc_notify_mq_msg_uv *msg;
+ enum xp_retval ret;
+
+ msg = container_of(payload, struct xpc_notify_mq_msg_uv, payload);
+
+ /* return an ACK to the sender of this message */
+
+ msg->hdr.partid = xp_partition_id;
+ msg->hdr.size = 0; /* size of zero indicates this is an ACK */
+
+ ret = xpc_send_gru_msg(ch->sn.uv.remote_notify_mq_gpa, msg,
+ sizeof(struct xpc_notify_mq_msghdr_uv));
+ if (ret != xpSuccess)
+ XPC_DEACTIVATE_PARTITION(&xpc_partitions[ch->partid], ret);
+
+ msg->hdr.msg_slot_number += ch->remote_nentries;
+}
+
+int
+xpc_init_uv(void)
+{
+ xpc_setup_partitions_sn = xpc_setup_partitions_sn_uv;
+ xpc_process_activate_IRQ_rcvd = xpc_process_activate_IRQ_rcvd_uv;
+ xpc_get_partition_rsvd_page_pa = xpc_get_partition_rsvd_page_pa_uv;
+ xpc_setup_rsvd_page_sn = xpc_setup_rsvd_page_sn_uv;
+ xpc_increment_heartbeat = xpc_increment_heartbeat_uv;
+ xpc_offline_heartbeat = xpc_offline_heartbeat_uv;
+ xpc_online_heartbeat = xpc_online_heartbeat_uv;
+ xpc_heartbeat_init = xpc_heartbeat_init_uv;
+ xpc_heartbeat_exit = xpc_heartbeat_exit_uv;
+ xpc_get_remote_heartbeat = xpc_get_remote_heartbeat_uv;
+
+ xpc_request_partition_activation = xpc_request_partition_activation_uv;
+ xpc_request_partition_reactivation =
+ xpc_request_partition_reactivation_uv;
+ xpc_request_partition_deactivation =
+ xpc_request_partition_deactivation_uv;
+ xpc_cancel_partition_deactivation_request =
+ xpc_cancel_partition_deactivation_request_uv;
+
+ xpc_setup_ch_structures_sn = xpc_setup_ch_structures_sn_uv;
+ xpc_teardown_ch_structures_sn = xpc_teardown_ch_structures_sn_uv;
+
+ xpc_make_first_contact = xpc_make_first_contact_uv;
+
+ xpc_get_chctl_all_flags = xpc_get_chctl_all_flags_uv;
+ xpc_send_chctl_closerequest = xpc_send_chctl_closerequest_uv;
+ xpc_send_chctl_closereply = xpc_send_chctl_closereply_uv;
+ xpc_send_chctl_openrequest = xpc_send_chctl_openrequest_uv;
+ xpc_send_chctl_openreply = xpc_send_chctl_openreply_uv;
+
+ xpc_save_remote_msgqueue_pa = xpc_save_remote_msgqueue_pa_uv;
+
+ xpc_setup_msg_structures = xpc_setup_msg_structures_uv;
+ xpc_teardown_msg_structures = xpc_teardown_msg_structures_uv;
+
+ xpc_indicate_partition_engaged = xpc_indicate_partition_engaged_uv;
+ xpc_indicate_partition_disengaged =
+ xpc_indicate_partition_disengaged_uv;
+ xpc_assume_partition_disengaged = xpc_assume_partition_disengaged_uv;
+ xpc_partition_engaged = xpc_partition_engaged_uv;
+ xpc_any_partition_engaged = xpc_any_partition_engaged_uv;
+
+ xpc_n_of_deliverable_payloads = xpc_n_of_deliverable_payloads_uv;
+ xpc_process_msg_chctl_flags = xpc_process_msg_chctl_flags_uv;
+ xpc_send_payload = xpc_send_payload_uv;
+ xpc_notify_senders_of_disconnect = xpc_notify_senders_of_disconnect_uv;
+ xpc_get_deliverable_payload = xpc_get_deliverable_payload_uv;
+ xpc_received_payload = xpc_received_payload_uv;
+
+ if (sizeof(struct xpc_notify_mq_msghdr_uv) > XPC_MSG_HDR_MAX_SIZE) {
+ dev_err(xpc_part, "xpc_notify_mq_msghdr_uv is larger than %d\n",
+ XPC_MSG_HDR_MAX_SIZE);
+ return -E2BIG;
+ }
+
+ /* ??? The cpuid argument's value is 0, is that what we want? */
+ /* !!! The irq argument's value isn't correct. */
+ xpc_activate_mq_uv = xpc_create_gru_mq_uv(XPC_ACTIVATE_MQ_SIZE_UV, 0, 0,
+ xpc_handle_activate_IRQ_uv);
+ if (xpc_activate_mq_uv == NULL)
+ return -ENOMEM;
+
+ /* ??? The cpuid argument's value is 0, is that what we want? */
+ /* !!! The irq argument's value isn't correct. */
+ xpc_notify_mq_uv = xpc_create_gru_mq_uv(XPC_NOTIFY_MQ_SIZE_UV, 0, 0,
+ xpc_handle_notify_IRQ_uv);
+ if (xpc_notify_mq_uv == NULL) {
+ /* !!! The irq argument's value isn't correct. */
+ xpc_destroy_gru_mq_uv(xpc_activate_mq_uv,
+ XPC_ACTIVATE_MQ_SIZE_UV, 0);
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+void
+xpc_exit_uv(void)
+{
+ /* !!! The irq argument's value isn't correct. */
+ xpc_destroy_gru_mq_uv(xpc_notify_mq_uv, XPC_NOTIFY_MQ_SIZE_UV, 0);
+
+ /* !!! The irq argument's value isn't correct. */
+ xpc_destroy_gru_mq_uv(xpc_activate_mq_uv, XPC_ACTIVATE_MQ_SIZE_UV, 0);
+}
*/
#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
-#include <linux/delay.h>
-#include <linux/ethtool.h>
-#include <linux/mii.h>
-#include <linux/smp.h>
-#include <linux/string.h>
-#include <asm/sn/bte.h>
-#include <asm/sn/io.h>
-#include <asm/sn/sn_sal.h>
-#include <asm/atomic.h>
#include "xp.h"
/*
u16 version; /* Version for this message */
u16 embedded_bytes; /* #of bytes embedded in XPC message */
u32 magic; /* Special number indicating this is xpnet */
- u64 buf_pa; /* phys address of buffer to retrieve */
+ unsigned long buf_pa; /* phys address of buffer to retrieve */
u32 size; /* #of bytes in buffer */
u8 leadin_ignore; /* #of bytes to ignore at the beginning */
u8 tailout_ignore; /* #of bytes to ignore at the end */
*
* XPC expects each message to exist in an individual cacheline.
*/
-#define XPNET_MSG_SIZE (L1_CACHE_BYTES - XPC_MSG_PAYLOAD_OFFSET)
+#define XPNET_MSG_SIZE XPC_MSG_PAYLOAD_MAX_SIZE
#define XPNET_MSG_DATA_MAX \
- (XPNET_MSG_SIZE - (u64)(&((struct xpnet_message *)0)->data))
-#define XPNET_MSG_ALIGNED_SIZE (L1_CACHE_ALIGN(XPNET_MSG_SIZE))
-#define XPNET_MSG_NENTRIES (PAGE_SIZE / XPNET_MSG_ALIGNED_SIZE)
+ (XPNET_MSG_SIZE - offsetof(struct xpnet_message, data))
+#define XPNET_MSG_NENTRIES (PAGE_SIZE / XPC_MSG_MAX_SIZE)
#define XPNET_MAX_KTHREADS (XPNET_MSG_NENTRIES + 1)
#define XPNET_MAX_IDLE_KTHREADS (XPNET_MSG_NENTRIES + 1)
* then be released.
*/
struct xpnet_pending_msg {
- struct list_head free_list;
struct sk_buff *skb;
atomic_t use_count;
};
* When we are notified of other partitions activating, we add them to
* our bitmask of partitions to which we broadcast.
*/
-static u64 xpnet_broadcast_partitions;
+static unsigned long *xpnet_broadcast_partitions;
/* protect above */
static DEFINE_SPINLOCK(xpnet_broadcast_lock);
#define XPNET_DEF_MTU (0x8000UL)
/*
- * The partition id is encapsulated in the MAC address. The following
- * define locates the octet the partid is in.
+ * The partid is encapsulated in the MAC address beginning in the following
+ * octet and it consists of two octets.
*/
-#define XPNET_PARTID_OCTET 1
-#define XPNET_LICENSE_OCTET 2
+#define XPNET_PARTID_OCTET 2
+
+/* Define the XPNET debug device structures to be used with dev_dbg() et al */
-/*
- * Define the XPNET debug device structure that is to be used with dev_dbg(),
- * dev_err(), dev_warn(), and dev_info().
- */
struct device_driver xpnet_dbg_name = {
.name = "xpnet"
};
xpnet_receive(short partid, int channel, struct xpnet_message *msg)
{
struct sk_buff *skb;
- bte_result_t bret;
+ void *dst;
+ enum xp_retval ret;
struct xpnet_dev_private *priv =
(struct xpnet_dev_private *)xpnet_device->priv;
/*
* The allocated skb has some reserved space.
- * In order to use bte_copy, we need to get the
+ * In order to use xp_remote_memcpy(), we need to get the
* skb->data pointer moved forward.
*/
skb_reserve(skb, (L1_CACHE_BYTES - ((u64)skb->data &
skb_copy_to_linear_data(skb, &msg->data,
(size_t)msg->embedded_bytes);
} else {
+ dst = (void *)((u64)skb->data & ~(L1_CACHE_BYTES - 1));
dev_dbg(xpnet, "transferring buffer to the skb->data area;\n\t"
- "bte_copy(0x%p, 0x%p, %hu)\n", (void *)msg->buf_pa,
- (void *)__pa((u64)skb->data & ~(L1_CACHE_BYTES - 1)),
- msg->size);
-
- bret = bte_copy(msg->buf_pa,
- __pa((u64)skb->data & ~(L1_CACHE_BYTES - 1)),
- msg->size, (BTE_NOTIFY | BTE_WACQUIRE), NULL);
+ "xp_remote_memcpy(0x%p, 0x%p, %hu)\n", dst,
+ (void *)msg->buf_pa, msg->size);
- if (bret != BTE_SUCCESS) {
+ ret = xp_remote_memcpy(xp_pa(dst), msg->buf_pa, msg->size);
+ if (ret != xpSuccess) {
/*
- * >>> Need better way of cleaning skb. Currently skb
- * >>> appears in_use and we can't just call
- * >>> dev_kfree_skb.
+ * !!! Need better way of cleaning skb. Currently skb
+ * !!! appears in_use and we can't just call
+ * !!! dev_kfree_skb.
*/
- dev_err(xpnet, "bte_copy(0x%p, 0x%p, 0x%hx) returned "
- "error=0x%x\n", (void *)msg->buf_pa,
- (void *)__pa((u64)skb->data &
- ~(L1_CACHE_BYTES - 1)),
- msg->size, bret);
+ dev_err(xpnet, "xp_remote_memcpy(0x%p, 0x%p, 0x%hx) "
+ "returned error=0x%x\n", dst,
+ (void *)msg->buf_pa, msg->size, ret);
xpc_received(partid, channel, (void *)msg);
xpnet_connection_activity(enum xp_retval reason, short partid, int channel,
void *data, void *key)
{
- long bp;
-
- DBUG_ON(partid <= 0 || partid >= XP_MAX_PARTITIONS);
+ DBUG_ON(partid < 0 || partid >= xp_max_npartitions);
DBUG_ON(channel != XPC_NET_CHANNEL);
switch (reason) {
case xpConnected: /* connection completed to a partition */
spin_lock_bh(&xpnet_broadcast_lock);
- xpnet_broadcast_partitions |= 1UL << (partid - 1);
- bp = xpnet_broadcast_partitions;
+ __set_bit(partid, xpnet_broadcast_partitions);
spin_unlock_bh(&xpnet_broadcast_lock);
netif_carrier_on(xpnet_device);
- dev_dbg(xpnet, "%s connection created to partition %d; "
- "xpnet_broadcast_partitions=0x%lx\n",
- xpnet_device->name, partid, bp);
+ dev_dbg(xpnet, "%s connected to partition %d\n",
+ xpnet_device->name, partid);
break;
default:
spin_lock_bh(&xpnet_broadcast_lock);
- xpnet_broadcast_partitions &= ~(1UL << (partid - 1));
- bp = xpnet_broadcast_partitions;
+ __clear_bit(partid, xpnet_broadcast_partitions);
spin_unlock_bh(&xpnet_broadcast_lock);
- if (bp == 0)
+ if (bitmap_empty((unsigned long *)xpnet_broadcast_partitions,
+ xp_max_npartitions)) {
netif_carrier_off(xpnet_device);
+ }
- dev_dbg(xpnet, "%s disconnected from partition %d; "
- "xpnet_broadcast_partitions=0x%lx\n",
- xpnet_device->name, partid, bp);
+ dev_dbg(xpnet, "%s disconnected from partition %d\n",
+ xpnet_device->name, partid);
break;
-
}
}
dev_dbg(xpnet, "calling xpc_connect(%d, 0x%p, NULL, %ld, %ld, %ld, "
"%ld)\n", XPC_NET_CHANNEL, xpnet_connection_activity,
- XPNET_MSG_SIZE, XPNET_MSG_NENTRIES, XPNET_MAX_KTHREADS,
- XPNET_MAX_IDLE_KTHREADS);
+ (unsigned long)XPNET_MSG_SIZE,
+ (unsigned long)XPNET_MSG_NENTRIES,
+ (unsigned long)XPNET_MAX_KTHREADS,
+ (unsigned long)XPNET_MAX_IDLE_KTHREADS);
ret = xpc_connect(XPC_NET_CHANNEL, xpnet_connection_activity, NULL,
XPNET_MSG_SIZE, XPNET_MSG_NENTRIES,
}
}
+static void
+xpnet_send(struct sk_buff *skb, struct xpnet_pending_msg *queued_msg,
+ u64 start_addr, u64 end_addr, u16 embedded_bytes, int dest_partid)
+{
+ u8 msg_buffer[XPNET_MSG_SIZE];
+ struct xpnet_message *msg = (struct xpnet_message *)&msg_buffer;
+ u16 msg_size = sizeof(struct xpnet_message);
+ enum xp_retval ret;
+
+ msg->embedded_bytes = embedded_bytes;
+ if (unlikely(embedded_bytes != 0)) {
+ msg->version = XPNET_VERSION_EMBED;
+ dev_dbg(xpnet, "calling memcpy(0x%p, 0x%p, 0x%lx)\n",
+ &msg->data, skb->data, (size_t)embedded_bytes);
+ skb_copy_from_linear_data(skb, &msg->data,
+ (size_t)embedded_bytes);
+ msg_size += embedded_bytes - 1;
+ } else {
+ msg->version = XPNET_VERSION;
+ }
+ msg->magic = XPNET_MAGIC;
+ msg->size = end_addr - start_addr;
+ msg->leadin_ignore = (u64)skb->data - start_addr;
+ msg->tailout_ignore = end_addr - (u64)skb_tail_pointer(skb);
+ msg->buf_pa = xp_pa((void *)start_addr);
+
+ dev_dbg(xpnet, "sending XPC message to %d:%d\n"
+ KERN_DEBUG "msg->buf_pa=0x%lx, msg->size=%u, "
+ "msg->leadin_ignore=%u, msg->tailout_ignore=%u\n",
+ dest_partid, XPC_NET_CHANNEL, msg->buf_pa, msg->size,
+ msg->leadin_ignore, msg->tailout_ignore);
+
+ atomic_inc(&queued_msg->use_count);
+
+ ret = xpc_send_notify(dest_partid, XPC_NET_CHANNEL, XPC_NOWAIT, msg,
+ msg_size, xpnet_send_completed, queued_msg);
+ if (unlikely(ret != xpSuccess))
+ atomic_dec(&queued_msg->use_count);
+}
+
/*
* Network layer has formatted a packet (skb) and is ready to place it
* "on the wire". Prepare and send an xpnet_message to all partitions
* which have connected with us and are targets of this packet.
*
* MAC-NOTE: For the XPNET driver, the MAC address contains the
- * destination partition_id. If the destination partition id word
- * is 0xff, this packet is to broadcast to all partitions.
+ * destination partid. If the destination partid octets are 0xffff,
+ * this packet is to be broadcast to all connected partitions.
*/
static int
xpnet_dev_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct xpnet_pending_msg *queued_msg;
- enum xp_retval ret;
- struct xpnet_message *msg;
u64 start_addr, end_addr;
- long dp;
- u8 second_mac_octet;
short dest_partid;
- struct xpnet_dev_private *priv;
- u16 embedded_bytes;
-
- priv = (struct xpnet_dev_private *)dev->priv;
+ struct xpnet_dev_private *priv = (struct xpnet_dev_private *)dev->priv;
+ u16 embedded_bytes = 0;
dev_dbg(xpnet, ">skb->head=0x%p skb->data=0x%p skb->tail=0x%p "
"skb->end=0x%p skb->len=%d\n", (void *)skb->head,
(void *)skb->data, skb_tail_pointer(skb), skb_end_pointer(skb),
skb->len);
+ if (skb->data[0] == 0x33) {
+ dev_kfree_skb(skb);
+ return 0; /* nothing needed to be done */
+ }
+
/*
* The xpnet_pending_msg tracks how many outstanding
* xpc_send_notifies are relying on this skb. When none
"packet\n", sizeof(struct xpnet_pending_msg));
priv->stats.tx_errors++;
-
return -ENOMEM;
}
end_addr = L1_CACHE_ALIGN((u64)skb_tail_pointer(skb));
/* calculate how many bytes to embed in the XPC message */
- embedded_bytes = 0;
if (unlikely(skb->len <= XPNET_MSG_DATA_MAX)) {
/* skb->data does fit so embed */
embedded_bytes = skb->len;
atomic_set(&queued_msg->use_count, 1);
queued_msg->skb = skb;
- second_mac_octet = skb->data[XPNET_PARTID_OCTET];
- if (second_mac_octet == 0xff) {
+ if (skb->data[0] == 0xff) {
/* we are being asked to broadcast to all partitions */
- dp = xpnet_broadcast_partitions;
- } else if (second_mac_octet != 0) {
- dp = xpnet_broadcast_partitions &
- (1UL << (second_mac_octet - 1));
- } else {
- /* 0 is an invalid partid. Ignore */
- dp = 0;
- }
- dev_dbg(xpnet, "destination Partitions mask (dp) = 0x%lx\n", dp);
-
- /*
- * If we wanted to allow promiscuous mode to work like an
- * unswitched network, this would be a good point to OR in a
- * mask of partitions which should be receiving all packets.
- */
-
- /*
- * Main send loop.
- */
- for (dest_partid = 1; dp && dest_partid < XP_MAX_PARTITIONS;
- dest_partid++) {
+ for_each_bit(dest_partid, xpnet_broadcast_partitions,
+ xp_max_npartitions) {
- if (!(dp & (1UL << (dest_partid - 1)))) {
- /* not destined for this partition */
- continue;
+ xpnet_send(skb, queued_msg, start_addr, end_addr,
+ embedded_bytes, dest_partid);
}
+ } else {
+ dest_partid = (short)skb->data[XPNET_PARTID_OCTET + 1];
+ dest_partid |= (short)skb->data[XPNET_PARTID_OCTET + 0] << 8;
- /* remove this partition from the destinations mask */
- dp &= ~(1UL << (dest_partid - 1));
-
- /* found a partition to send to */
-
- ret = xpc_allocate(dest_partid, XPC_NET_CHANNEL,
- XPC_NOWAIT, (void **)&msg);
- if (unlikely(ret != xpSuccess))
- continue;
-
- msg->embedded_bytes = embedded_bytes;
- if (unlikely(embedded_bytes != 0)) {
- msg->version = XPNET_VERSION_EMBED;
- dev_dbg(xpnet, "calling memcpy(0x%p, 0x%p, 0x%lx)\n",
- &msg->data, skb->data, (size_t)embedded_bytes);
- skb_copy_from_linear_data(skb, &msg->data,
- (size_t)embedded_bytes);
- } else {
- msg->version = XPNET_VERSION;
- }
- msg->magic = XPNET_MAGIC;
- msg->size = end_addr - start_addr;
- msg->leadin_ignore = (u64)skb->data - start_addr;
- msg->tailout_ignore = end_addr - (u64)skb_tail_pointer(skb);
- msg->buf_pa = __pa(start_addr);
-
- dev_dbg(xpnet, "sending XPC message to %d:%d\n"
- KERN_DEBUG "msg->buf_pa=0x%lx, msg->size=%u, "
- "msg->leadin_ignore=%u, msg->tailout_ignore=%u\n",
- dest_partid, XPC_NET_CHANNEL, msg->buf_pa, msg->size,
- msg->leadin_ignore, msg->tailout_ignore);
-
- atomic_inc(&queued_msg->use_count);
-
- ret = xpc_send_notify(dest_partid, XPC_NET_CHANNEL, msg,
- xpnet_send_completed, queued_msg);
- if (unlikely(ret != xpSuccess)) {
- atomic_dec(&queued_msg->use_count);
- continue;
+ if (dest_partid >= 0 &&
+ dest_partid < xp_max_npartitions &&
+ test_bit(dest_partid, xpnet_broadcast_partitions) != 0) {
+
+ xpnet_send(skb, queued_msg, start_addr, end_addr,
+ embedded_bytes, dest_partid);
}
}
if (atomic_dec_return(&queued_msg->use_count) == 0) {
- dev_dbg(xpnet, "no partitions to receive packet destined for "
- "%d\n", dest_partid);
-
dev_kfree_skb(skb);
kfree(queued_msg);
}
static int __init
xpnet_init(void)
{
- int i;
- u32 license_num;
- int result = -ENOMEM;
+ int result;
- if (!ia64_platform_is("sn2"))
+ if (!is_shub() && !is_uv())
return -ENODEV;
dev_info(xpnet, "registering network device %s\n", XPNET_DEVICE_NAME);
+ xpnet_broadcast_partitions = kzalloc(BITS_TO_LONGS(xp_max_npartitions) *
+ sizeof(long), GFP_KERNEL);
+ if (xpnet_broadcast_partitions == NULL)
+ return -ENOMEM;
+
/*
* use ether_setup() to init the majority of our device
* structure and then override the necessary pieces.
*/
xpnet_device = alloc_netdev(sizeof(struct xpnet_dev_private),
XPNET_DEVICE_NAME, ether_setup);
- if (xpnet_device == NULL)
+ if (xpnet_device == NULL) {
+ kfree(xpnet_broadcast_partitions);
return -ENOMEM;
+ }
netif_carrier_off(xpnet_device);
* MAC addresses. We chose the first octet of the MAC to be unlikely
* to collide with any vendor's officially issued MAC.
*/
- xpnet_device->dev_addr[0] = 0xfe;
- xpnet_device->dev_addr[XPNET_PARTID_OCTET] = sn_partition_id;
- license_num = sn_partition_serial_number_val();
- for (i = 3; i >= 0; i--) {
- xpnet_device->dev_addr[XPNET_LICENSE_OCTET + i] =
- license_num & 0xff;
- license_num = license_num >> 8;
- }
+ xpnet_device->dev_addr[0] = 0x02; /* locally administered, no OUI */
+
+ xpnet_device->dev_addr[XPNET_PARTID_OCTET + 1] = xp_partition_id;
+ xpnet_device->dev_addr[XPNET_PARTID_OCTET + 0] = (xp_partition_id >> 8);
/*
* ether_setup() sets this to a multicast device. We are
xpnet_device->features = NETIF_F_NO_CSUM;
result = register_netdev(xpnet_device);
- if (result != 0)
+ if (result != 0) {
free_netdev(xpnet_device);
+ kfree(xpnet_broadcast_partitions);
+ }
return result;
}
xpnet_device[0].name);
unregister_netdev(xpnet_device);
-
free_netdev(xpnet_device);
+ kfree(xpnet_broadcast_partitions);
}
module_exit(xpnet_exit);
struct mmc_blk_data *md = mq->data;
struct mmc_card *card = md->queue.card;
struct mmc_blk_request brq;
- int ret = 1, sg_pos, data_size;
+ int ret = 1, data_size, i;
+ struct scatterlist *sg;
mmc_claim_host(card->host);
mmc_queue_bounce_pre(mq);
+ /*
+ * Adjust the sg list so it is the same size as the
+ * request.
+ */
if (brq.data.blocks !=
(req->nr_sectors >> (md->block_bits - 9))) {
data_size = brq.data.blocks * brq.data.blksz;
- for (sg_pos = 0; sg_pos < brq.data.sg_len; sg_pos++) {
- data_size -= mq->sg[sg_pos].length;
+ for_each_sg(brq.data.sg, sg, brq.data.sg_len, i) {
+ data_size -= sg->length;
if (data_size <= 0) {
- mq->sg[sg_pos].length += data_size;
- sg_pos++;
+ sg->length += data_size;
+ i++;
break;
}
}
- brq.data.sg_len = sg_pos;
+ brq.data.sg_len = i;
}
mmc_wait_for_req(card->host, &brq.mrq);
int ret, i;
unsigned long flags;
- BUG_ON(blocks * blksz > BUFFER_SIZE);
-
if (write) {
for (i = 0;i < blocks * blksz;i++)
test->scratch[i] = i;
} else {
- memset(test->scratch, 0, blocks * blksz);
+ memset(test->scratch, 0, BUFFER_SIZE);
}
local_irq_save(flags);
- sg_copy_from_buffer(sg, sg_len, test->scratch, blocks * blksz);
+ sg_copy_from_buffer(sg, sg_len, test->scratch, BUFFER_SIZE);
local_irq_restore(flags);
ret = mmc_test_set_blksize(test, blksz);
}
} else {
local_irq_save(flags);
- sg_copy_to_buffer(sg, sg_len, test->scratch, blocks * blksz);
+ sg_copy_to_buffer(sg, sg_len, test->scratch, BUFFER_SIZE);
local_irq_restore(flags);
for (i = 0;i < blocks * blksz;i++) {
if (test->scratch[i] != (u8)i)
return 0;
}
-static int mmc_test_bigsg_write(struct mmc_test_card *test)
-{
- int ret;
- unsigned int size;
- struct scatterlist sg;
-
- if (test->card->host->max_blk_count == 1)
- return RESULT_UNSUP_HOST;
-
- size = PAGE_SIZE * 2;
- size = min(size, test->card->host->max_req_size);
- size = min(size, test->card->host->max_seg_size);
- size = min(size, test->card->host->max_blk_count * 512);
-
- memset(test->buffer, 0, BUFFER_SIZE);
-
- if (size < 1024)
- return RESULT_UNSUP_HOST;
-
- sg_init_table(&sg, 1);
- sg_init_one(&sg, test->buffer, BUFFER_SIZE);
-
- ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 1);
- if (ret)
- return ret;
-
- return 0;
-}
-
-static int mmc_test_bigsg_read(struct mmc_test_card *test)
-{
- int ret, i;
- unsigned int size;
- struct scatterlist sg;
-
- if (test->card->host->max_blk_count == 1)
- return RESULT_UNSUP_HOST;
-
- size = PAGE_SIZE * 2;
- size = min(size, test->card->host->max_req_size);
- size = min(size, test->card->host->max_seg_size);
- size = min(size, test->card->host->max_blk_count * 512);
-
- if (size < 1024)
- return RESULT_UNSUP_HOST;
-
- memset(test->buffer, 0xCD, BUFFER_SIZE);
-
- sg_init_table(&sg, 1);
- sg_init_one(&sg, test->buffer, BUFFER_SIZE);
- ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 0);
- if (ret)
- return ret;
-
- /* mmc_test_transfer() doesn't check for read overflows */
- for (i = size;i < BUFFER_SIZE;i++) {
- if (test->buffer[i] != 0xCD)
- return RESULT_FAIL;
- }
-
- return 0;
-}
-
#ifdef CONFIG_HIGHMEM
static int mmc_test_write_high(struct mmc_test_card *test)
.run = mmc_test_multi_xfersize_read,
},
- {
- .name = "Over-sized SG list write",
- .prepare = mmc_test_prepare_write,
- .run = mmc_test_bigsg_write,
- .cleanup = mmc_test_cleanup,
- },
-
- {
- .name = "Over-sized SG list read",
- .prepare = mmc_test_prepare_read,
- .run = mmc_test_bigsg_read,
- .cleanup = mmc_test_cleanup,
- },
-
#ifdef CONFIG_HIGHMEM
{
{
#ifdef CONFIG_MMC_DEBUG
unsigned int i, sz;
+ struct scatterlist *sg;
#endif
pr_debug("%s: starting CMD%u arg %08x flags %08x\n",
#ifdef CONFIG_MMC_DEBUG
sz = 0;
- for (i = 0;i < mrq->data->sg_len;i++)
- sz += mrq->data->sg[i].length;
+ for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i)
+ sz += sg->length;
BUG_ON(sz != mrq->data->blocks * mrq->data->blksz);
#endif
#include <asm/gpio.h>
#include <asm/mach/mmc.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/at91_mci.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
+#include <mach/at91_mci.h>
#define DRIVER_NAME "at91_mci"
#include <asm/io.h>
#include <asm/unaligned.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#include "atmel-mci-regs.h"
/* Hardware definitions */
#define AU1XMMC_DESCRIPTOR_COUNT 1
-#define AU1XMMC_DESCRIPTOR_SIZE 2048
+
+/* max DMA seg size: 64KB on Au1100, 4MB on Au1200 */
+#ifdef CONFIG_SOC_AU1100
+#define AU1XMMC_DESCRIPTOR_SIZE 0x0000ffff
+#else /* Au1200 */
+#define AU1XMMC_DESCRIPTOR_SIZE 0x003fffff
+#endif
#define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \
MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/sizes.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/imx-dma.h>
+#include <mach/mmc.h>
+#include <mach/imx-dma.h>
#include "imxmmc.h"
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/mach-types.h>
-
-#include <asm/arch/board.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/fpga.h>
+
+#include <mach/board.h>
+#include <mach/mmc.h>
+#include <mach/gpio.h>
+#include <mach/dma.h>
+#include <mach/mux.h>
+#include <mach/fpga.h>
#define OMAP_MMC_REG_CMD 0x00
#define OMAP_MMC_REG_ARGL 0x04
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mmc.h>
+#include <mach/pxa-regs.h>
+#include <mach/mmc.h>
#include "pxamci.h"
#include <asm/dma.h>
-#include <asm/arch/regs-sdi.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-sdi.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/mci.h>
chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR |
SDHCI_QUIRK_32BIT_DMA_SIZE |
SDHCI_QUIRK_32BIT_ADMA_SIZE |
- SDHCI_QUIRK_RESET_AFTER_REQUEST;
+ SDHCI_QUIRK_RESET_AFTER_REQUEST |
+ SDHCI_QUIRK_BROKEN_SMALL_PIO;
}
/*
else
mask = SDHCI_SPACE_AVAILABLE;
+ /*
+ * Some controllers (JMicron JMB38x) mess up the buffer bits
+ * for transfers < 4 bytes. As long as it is just one block,
+ * we can ignore the bits.
+ */
+ if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
+ (host->data->blocks == 1))
+ mask = ~0;
+
while (readl(host->ioaddr + SDHCI_PRESENT_STATE) & mask) {
if (host->data->flags & MMC_DATA_READ)
sdhci_read_block_pio(host);
host->adma_addr = dma_map_single(mmc_dev(host->mmc),
host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE);
- if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
+ if (dma_mapping_error(mmc_dev(host->mmc), host->adma_addr))
goto unmap_entries;
BUG_ON(host->adma_addr & 0x3);
* us an invalid request.
*/
WARN_ON(1);
- host->flags &= ~SDHCI_USE_DMA;
+ host->flags &= ~SDHCI_REQ_USE_DMA;
} else {
writel(host->adma_addr,
host->ioaddr + SDHCI_ADMA_ADDRESS);
* us an invalid request.
*/
WARN_ON(1);
- host->flags &= ~SDHCI_USE_DMA;
+ host->flags &= ~SDHCI_REQ_USE_DMA;
} else {
WARN_ON(sg_cnt != 1);
writel(sg_dma_address(data->sg),
#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11)
/* Controller provides an incorrect timeout value for transfers */
#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12)
+/* Controller has an issue with buffer bits for small transfers */
+#define SDHCI_QUIRK_BROKEN_SMALL_PIO (1<<13)
int irq; /* Device IRQ */
void __iomem * ioaddr; /* Mapped address */
/* AMD */
-#define AM29DL800BB 0x22C8
+#define AM29DL800BB 0x22CB
#define AM29DL800BT 0x224A
#define AM29F800BB 0x2258
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/mutex.h>
+#include <linux/err.h>
+
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
device->write = dataflash_write;
device->priv = priv;
- dev_info(&spi->dev, "%s (%d KBytes) pagesize %d bytes, "
- "erasesize %d bytes\n", name, device->size/1024,
- pagesize, pagesize * 8); /* 8 pages = 1 block */
+ dev_info(&spi->dev, "%s (%d KBytes) pagesize %d bytes\n",
+ name, DIV_ROUND_UP(device->size, 1024), pagesize);
dev_set_drvdata(&spi->dev, priv);
if (mtd_has_partitions()) {
return add_mtd_device(device) == 1 ? -ENODEV : 0;
}
-/*
- * Detect and initialize DataFlash device:
- *
- * Device Density ID code #Pages PageSize Offset
- * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
- * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
- * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
- * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
- * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
- * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
- * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
- * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
- */
-
struct flash_info {
char *name;
- /* JEDEC id zero means "no ID" (most older chips); otherwise it has
- * a high byte of zero plus three data bytes: the manufacturer id,
- * then a two byte device id.
+ /* JEDEC id has a high byte of zero plus three data bytes:
+ * the manufacturer id, then a two byte device id.
*/
uint32_t jedec_id;
- /* The size listed here is what works with OPCODE_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
+ /* The size listed here is what works with OP_ERASE_PAGE. */
unsigned nr_pages;
uint16_t pagesize;
uint16_t pageoffset;
uint16_t flags;
-#define SUP_POW2PS 0x02
-#define IS_POW2PS 0x01
+#define SUP_POW2PS 0x0002 /* supports 2^N byte pages */
+#define IS_POW2PS 0x0001 /* uses 2^N byte pages */
};
static struct flash_info __devinitdata dataflash_data [] = {
- { "at45db011d", 0x1f2200, 512, 264, 9, SUP_POW2PS},
+ /*
+ * NOTE: chips with SUP_POW2PS (rev D and up) need two entries,
+ * one with IS_POW2PS and the other without. The entry with the
+ * non-2^N byte page size can't name exact chip revisions without
+ * losing backwards compatibility for cmdlinepart.
+ *
+ * These newer chips also support 128-byte security registers (with
+ * 64 bytes one-time-programmable) and software write-protection.
+ */
+ { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS},
{ "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db021d", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
+ { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS},
{ "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db041d", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
+ { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS},
{ "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db081d", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
+ { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS},
{ "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
- { "at45db161d", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
+ { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS},
{ "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
- { "at45db321c", 0x1f2700, 8192, 528, 10, },
+ { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */
- { "at45db321d", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
+ { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS},
{ "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
- { "at45db641d", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
- { "at45db641d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
+ { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS},
+ { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
};
static struct flash_info *__devinit jedec_probe(struct spi_device *spi)
struct flash_info *info;
int status;
-
/* JEDEC also defines an optional "extended device information"
* string for after vendor-specific data, after the three bytes
* we use here. Supporting some chips might require using it.
+ *
+ * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
+ * That's not an error; only rev C and newer chips handle it, and
+ * only Atmel sells these chips.
*/
tmp = spi_write_then_read(spi, &code, 1, id, 3);
if (tmp < 0) {
DEBUG(MTD_DEBUG_LEVEL0, "%s: error %d reading JEDEC ID\n",
spi->dev.bus_id, tmp);
- return NULL;
+ return ERR_PTR(tmp);
}
+ if (id[0] != 0x1f)
+ return NULL;
+
jedec = id[0];
jedec = jedec << 8;
jedec |= id[1];
tmp < ARRAY_SIZE(dataflash_data);
tmp++, info++) {
if (info->jedec_id == jedec) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: OTP, sector protect%s\n",
+ dev_name(&spi->dev),
+ (info->flags & SUP_POW2PS)
+ ? ", binary pagesize" : ""
+ );
if (info->flags & SUP_POW2PS) {
status = dataflash_status(spi);
- if (status & 0x1)
- /* return power of 2 pagesize */
- return ++info;
- else
- return info;
+ if (status < 0) {
+ DEBUG(MTD_DEBUG_LEVEL1,
+ "%s: status error %d\n",
+ dev_name(&spi->dev), status);
+ return ERR_PTR(status);
+ }
+ if (status & 0x1) {
+ if (info->flags & IS_POW2PS)
+ return info;
+ } else {
+ if (!(info->flags & IS_POW2PS))
+ return info;
+ }
}
}
}
- return NULL;
+
+ /*
+ * Treat other chips as errors ... we won't know the right page
+ * size (it might be binary) even when we can tell which density
+ * class is involved (legacy chip id scheme).
+ */
+ dev_warn(&spi->dev, "JEDEC id %06x not handled\n", jedec);
+ return ERR_PTR(-ENODEV);
}
+/*
+ * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
+ * or else the ID code embedded in the status bits:
+ *
+ * Device Density ID code #Pages PageSize Offset
+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9
+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
+ * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
+ */
static int __devinit dataflash_probe(struct spi_device *spi)
{
int status;
* If it succeeds we know we have either a C or D part.
* D will support power of 2 pagesize option.
*/
-
info = jedec_probe(spi);
-
+ if (IS_ERR(info))
+ return PTR_ERR(info);
if (info != NULL)
return add_dataflash(spi, info->name, info->nr_pages,
info->pagesize, info->pageoffset);
-
+ /*
+ * Older chips support only legacy commands, identifing
+ * capacity using bits in the status byte.
+ */
status = dataflash_status(spi);
if (status <= 0 || status == 0xff) {
DEBUG(MTD_DEBUG_LEVEL1, "%s: status error %d\n",
status = add_dataflash(spi, "AT45DB021B", 1024, 264, 9);
break;
case 0x1c: /* 0 1 1 1 x x */
- status = add_dataflash(spi, "AT45DB041B", 2048, 264, 9);
+ status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9);
break;
case 0x24: /* 1 0 0 1 x x */
status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9);
break;
case 0x2c: /* 1 0 1 1 x x */
- status = add_dataflash(spi, "AT45DB161B", 4096, 528, 10);
+ status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10);
break;
case 0x34: /* 1 1 0 1 x x */
status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10);
#include <linux/init.h>
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/hardware.h>
-#include <asm/arch/autcpu12.h>
+#include <mach/hardware.h>
+#include <mach/autcpu12.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
#include <linux/mtd/partitions.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/concat.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/io.h>
#include <asm/sizes.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
#include <linux/mtd/partitions.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
static struct mtd_info *mymtd;
#include <linux/mtd/partitions.h>
#include <asm/mach/flash.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/system.h>
#include <linux/mtd/concat.h>
#endif
-#include <asm/hardware.h>
-#include <asm/arch-sa1100/h3600.h>
+#include <mach/hardware.h>
+#include <mach/h3600.h>
#include <asm/io.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/flash.h>
#include <linux/reboot.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/flash.h>
-#include <asm/arch/tc.h>
+#include <mach/tc.h>
#ifdef CONFIG_MTD_PARTITIONS
static const char *part_probes[] = { /* "RedBoot", */ "cmdlinepart", NULL };
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/cacheflush.h>
#include <asm/mach/flash.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/concat.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/sizes.h>
#include <asm/mach/flash.h>
int (*fill_super)(struct super_block *, void *, int),
struct vfsmount *mnt)
{
- struct nameidata nd;
- int mtdnr, ret;
+#ifdef CONFIG_BLOCK
+ struct block_device *bdev;
+ int ret, major;
+#endif
+ int mtdnr;
if (!dev_name)
return -EINVAL;
}
}
+#ifdef CONFIG_BLOCK
/* try the old way - the hack where we allowed users to mount
* /dev/mtdblock$(n) but didn't actually _use_ the blockdev
*/
- ret = path_lookup(dev_name, LOOKUP_FOLLOW, &nd);
-
- DEBUG(1, "MTDSB: path_lookup() returned %d, inode %p\n",
- ret, nd.path.dentry ? nd.path.dentry->d_inode : NULL);
-
- if (ret)
+ bdev = lookup_bdev(dev_name);
+ if (IS_ERR(bdev)) {
+ ret = PTR_ERR(bdev);
+ DEBUG(1, "MTDSB: lookup_bdev() returned %d\n", ret);
return ret;
+ }
+ DEBUG(1, "MTDSB: lookup_bdev() returned 0\n");
ret = -EINVAL;
- if (!S_ISBLK(nd.path.dentry->d_inode->i_mode))
- goto out;
-
- if (nd.path.mnt->mnt_flags & MNT_NODEV) {
- ret = -EACCES;
- goto out;
- }
+ major = MAJOR(bdev->bd_dev);
+ mtdnr = MINOR(bdev->bd_dev);
+ bdput(bdev);
- if (imajor(nd.path.dentry->d_inode) != MTD_BLOCK_MAJOR)
+ if (major != MTD_BLOCK_MAJOR)
goto not_an_MTD_device;
- mtdnr = iminor(nd.path.dentry->d_inode);
- path_put(&nd.path);
-
return get_sb_mtd_nr(fs_type, flags, dev_name, data, mtdnr, fill_super,
mnt);
not_an_MTD_device:
+#endif /* CONFIG_BLOCK */
+
if (!(flags & MS_SILENT))
printk(KERN_NOTICE
"MTD: Attempt to mount non-MTD device \"%s\"\n",
dev_name);
-out:
- path_put(&nd.path);
- return ret;
-
+ return -EINVAL;
}
EXPORT_SYMBOL_GPL(get_sb_mtd);
config MTD_NAND_BF5XX_HWECC
bool "BF5XX NAND Hardware ECC"
+ default y
depends on MTD_NAND_BF5XX
help
Enable the use of the BF5XX's internal ECC generator when
using NAND.
+config MTD_NAND_BF5XX_BOOTROM_ECC
+ bool "Use Blackfin BootROM ECC Layout"
+ default n
+ depends on MTD_NAND_BF5XX_HWECC
+ help
+ If you wish to modify NAND pages and allow the Blackfin on-chip
+ BootROM to boot from them, say Y here. This is only necessary
+ if you are booting U-Boot out of NAND and you wish to update
+ U-Boot from Linux' userspace. Otherwise, you should say N here.
+
+ If unsure, say N.
+
config MTD_NAND_RTC_FROM4
tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)"
depends on SH_SOLUTION_ENGINE
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/sizes.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/board-ams-delta.h>
+#include <mach/gpio.h>
+#include <mach/board-ams-delta.h>
/*
* MTD structure for E3 (Delta)
#include <linux/gpio.h>
#include <linux/io.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
#ifdef CONFIG_MTD_NAND_ATMEL_ECC_HW
#define hard_ecc 1
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/sizes.h>
-#include <asm/arch/autcpu12.h>
+#include <mach/autcpu12.h>
/*
* MTD structure for AUTCPU12 board
P_NAND_ALE,
0};
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+static uint8_t bbt_pattern[] = { 0xff };
+
+static struct nand_bbt_descr bootrom_bbt = {
+ .options = 0,
+ .offs = 63,
+ .len = 1,
+ .pattern = bbt_pattern,
+};
+
+static struct nand_ecclayout bootrom_ecclayout = {
+ .eccbytes = 24,
+ .eccpos = {
+ 0x8 * 0, 0x8 * 0 + 1, 0x8 * 0 + 2,
+ 0x8 * 1, 0x8 * 1 + 1, 0x8 * 1 + 2,
+ 0x8 * 2, 0x8 * 2 + 1, 0x8 * 2 + 2,
+ 0x8 * 3, 0x8 * 3 + 1, 0x8 * 3 + 2,
+ 0x8 * 4, 0x8 * 4 + 1, 0x8 * 4 + 2,
+ 0x8 * 5, 0x8 * 5 + 1, 0x8 * 5 + 2,
+ 0x8 * 6, 0x8 * 6 + 1, 0x8 * 6 + 2,
+ 0x8 * 7, 0x8 * 7 + 1, 0x8 * 7 + 2
+ },
+ .oobfree = {
+ { 0x8 * 0 + 3, 5 },
+ { 0x8 * 1 + 3, 5 },
+ { 0x8 * 2 + 3, 5 },
+ { 0x8 * 3 + 3, 5 },
+ { 0x8 * 4 + 3, 5 },
+ { 0x8 * 5 + 3, 5 },
+ { 0x8 * 6 + 3, 5 },
+ { 0x8 * 7 + 3, 5 },
+ }
+};
+#endif
+
/*
* Data structures for bf5xx nand flash controller driver
*/
dat += 256;
read_ecc += 8;
calc_ecc += 8;
- ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
+ ret |= bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
}
return ret;
ecc0 = bfin_read_NFC_ECC0();
ecc1 = bfin_read_NFC_ECC1();
- code[0] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
+ code[0] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
dev_dbg(info->device, "returning ecc 0x%08x\n", code[0]);
if (page_size == 512) {
ecc0 = bfin_read_NFC_ECC2();
ecc1 = bfin_read_NFC_ECC3();
- code[1] = (ecc0 & 0x3FF) | ((ecc1 & 0x3FF) << 11);
+ code[1] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
/* second 3 bytes in ecc_code for second 256
* bytes of 512 page size
/*
* System initialization functions
*/
-
static int bf5xx_nand_dma_init(struct bf5xx_nand_info *info)
{
int ret;
return 0;
}
+static void bf5xx_nand_dma_remove(struct bf5xx_nand_info *info)
+{
+ /* Free NFC DMA channel */
+ if (hardware_ecc)
+ free_dma(CH_NFC);
+}
+
/*
* BF5XX NFC hardware initialization
* - pin mux setup
#endif
}
-static int bf5xx_nand_remove(struct platform_device *pdev)
+static int __devexit bf5xx_nand_remove(struct platform_device *pdev)
{
struct bf5xx_nand_info *info = to_nand_info(pdev);
struct mtd_info *mtd = NULL;
}
peripheral_free_list(bfin_nfc_pin_req);
+ bf5xx_nand_dma_remove(info);
/* free the common resources */
kfree(info);
* it can allocate all necessary resources then calls the
* nand layer to look for devices
*/
-static int bf5xx_nand_probe(struct platform_device *pdev)
+static int __devinit bf5xx_nand_probe(struct platform_device *pdev)
{
struct bf5xx_nand_platform *plat = to_nand_plat(pdev);
struct bf5xx_nand_info *info = NULL;
dev_dbg(&pdev->dev, "(%p)\n", pdev);
- if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
- printk(KERN_ERR DRV_NAME
- ": Requesting Peripherals failed\n");
- return -EFAULT;
- }
-
if (!plat) {
dev_err(&pdev->dev, "no platform specific information\n");
- goto exit_error;
+ return -EINVAL;
+ }
+
+ if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
+ dev_err(&pdev->dev, "requesting Peripherals failed\n");
+ return -EFAULT;
}
info = kzalloc(sizeof(*info), GFP_KERNEL);
if (info == NULL) {
dev_err(&pdev->dev, "no memory for flash info\n");
err = -ENOMEM;
- goto exit_error;
+ goto out_err_kzalloc;
}
platform_set_drvdata(pdev, info);
/* initialise the hardware */
err = bf5xx_nand_hw_init(info);
- if (err != 0)
- goto exit_error;
+ if (err)
+ goto out_err_hw_init;
/* setup hardware ECC data struct */
if (hardware_ecc) {
+#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
+ chip->badblock_pattern = &bootrom_bbt;
+ chip->ecc.layout = &bootrom_ecclayout;
+#endif
+
if (plat->page_size == NFC_PG_SIZE_256) {
chip->ecc.bytes = 3;
chip->ecc.size = 256;
/* scan hardware nand chip and setup mtd info data struct */
if (nand_scan(mtd, 1)) {
err = -ENXIO;
- goto exit_error;
+ goto out_err_nand_scan;
}
/* add NAND partition */
dev_dbg(&pdev->dev, "initialised ok\n");
return 0;
-exit_error:
- bf5xx_nand_remove(pdev);
+out_err_nand_scan:
+ bf5xx_nand_dma_remove(info);
+out_err_hw_init:
+ platform_set_drvdata(pdev, NULL);
+ kfree(info);
+out_err_kzalloc:
+ peripheral_free_list(bfin_nfc_pin_req);
- if (err == 0)
- err = -EINVAL;
return err;
}
/* driver device registration */
static struct platform_driver bf5xx_nand_driver = {
.probe = bf5xx_nand_probe,
- .remove = bf5xx_nand_remove,
+ .remove = __devexit_p(bf5xx_nand_remove),
.suspend = bf5xx_nand_suspend,
.resume = bf5xx_nand_resume,
.driver = {
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
#define GPIO_NAND_CS (11)
#define GPIO_NAND_RB (89)
goto out;
mh = (struct NFTLMediaHeader *)buf;
- mh->NumEraseUnits = le16_to_cpu(mh->NumEraseUnits);
- mh->FirstPhysicalEUN = le16_to_cpu(mh->FirstPhysicalEUN);
- mh->FormattedSize = le32_to_cpu(mh->FormattedSize);
+ le16_to_cpus(&mh->NumEraseUnits);
+ le16_to_cpus(&mh->FirstPhysicalEUN);
+ le32_to_cpus(&mh->FormattedSize);
printk(KERN_INFO " DataOrgID = %s\n"
" NumEraseUnits = %d\n"
doc->mh1_page = doc->mh0_page + (4096 >> this->page_shift);
mh = (struct INFTLMediaHeader *)buf;
- mh->NoOfBootImageBlocks = le32_to_cpu(mh->NoOfBootImageBlocks);
- mh->NoOfBinaryPartitions = le32_to_cpu(mh->NoOfBinaryPartitions);
- mh->NoOfBDTLPartitions = le32_to_cpu(mh->NoOfBDTLPartitions);
- mh->BlockMultiplierBits = le32_to_cpu(mh->BlockMultiplierBits);
- mh->FormatFlags = le32_to_cpu(mh->FormatFlags);
- mh->PercentUsed = le32_to_cpu(mh->PercentUsed);
+ le32_to_cpus(&mh->NoOfBootImageBlocks);
+ le32_to_cpus(&mh->NoOfBinaryPartitions);
+ le32_to_cpus(&mh->NoOfBDTLPartitions);
+ le32_to_cpus(&mh->BlockMultiplierBits);
+ le32_to_cpus(&mh->FormatFlags);
+ le32_to_cpus(&mh->PercentUsed);
printk(KERN_INFO " bootRecordID = %s\n"
" NoOfBootImageBlocks = %d\n"
/* Scan the partitions */
for (i = 0; (i < 4); i++) {
ip = &(mh->Partitions[i]);
- ip->virtualUnits = le32_to_cpu(ip->virtualUnits);
- ip->firstUnit = le32_to_cpu(ip->firstUnit);
- ip->lastUnit = le32_to_cpu(ip->lastUnit);
- ip->flags = le32_to_cpu(ip->flags);
- ip->spareUnits = le32_to_cpu(ip->spareUnits);
- ip->Reserved0 = le32_to_cpu(ip->Reserved0);
+ le32_to_cpus(&ip->virtualUnits);
+ le32_to_cpus(&ip->firstUnit);
+ le32_to_cpus(&ip->lastUnit);
+ le32_to_cpus(&ip->flags);
+ le32_to_cpus(&ip->spareUnits);
+ le32_to_cpus(&ip->Reserved0);
printk(KERN_INFO " PARTITION[%d] ->\n"
" virtualUnits = %d\n"
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h> /* for CLPS7111_VIRT_BASE */
+#include <mach/hardware.h> /* for CLPS7111_VIRT_BASE */
#include <asm/sizes.h>
#include <asm/hardware/clps7111.h>
goto err;
}
- priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", res.start);
+ priv->mtd.name = kasprintf(GFP_KERNEL, "%x.flash", (unsigned)res.start);
if (!priv->mtd.name) {
ret = -ENOMEM;
goto err;
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h> /* for CLPS7111_VIRT_BASE */
+#include <mach/hardware.h> /* for CLPS7111_VIRT_BASE */
#include <asm/sizes.h>
-#include <asm/arch/h1900-gpio.h>
-#include <asm/arch/ipaq.h>
+#include <mach/h1900-gpio.h>
+#include <mach/ipaq.h>
/*
* MTD structure for EDB7312 board
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/vmalloc.h>
+#include <asm/div64.h>
#include <linux/slab.h>
#include <linux/errno.h>
#include <linux/string.h>
#define STATE_CMD_READID 0x0000000A /* read ID */
#define STATE_CMD_ERASE2 0x0000000B /* sector erase second command */
#define STATE_CMD_RESET 0x0000000C /* reset */
+#define STATE_CMD_RNDOUT 0x0000000D /* random output command */
+#define STATE_CMD_RNDOUTSTART 0x0000000E /* random output start command */
#define STATE_CMD_MASK 0x0000000F /* command states mask */
/* After an address is input, the simulator goes to one of these states */
#define STATE_ADDR_PAGE 0x00000010 /* full (row, column) address is accepted */
#define STATE_ADDR_SEC 0x00000020 /* sector address was accepted */
-#define STATE_ADDR_ZERO 0x00000030 /* one byte zero address was accepted */
-#define STATE_ADDR_MASK 0x00000030 /* address states mask */
+#define STATE_ADDR_COLUMN 0x00000030 /* column address was accepted */
+#define STATE_ADDR_ZERO 0x00000040 /* one byte zero address was accepted */
+#define STATE_ADDR_MASK 0x00000070 /* address states mask */
/* Durind data input/output the simulator is in these states */
#define STATE_DATAIN 0x00000100 /* waiting for data input */
#define ACTION_OOBOFF 0x00600000 /* add to address OOB offset */
#define ACTION_MASK 0x00700000 /* action mask */
-#define NS_OPER_NUM 12 /* Number of operations supported by the simulator */
+#define NS_OPER_NUM 13 /* Number of operations supported by the simulator */
#define NS_OPER_STATES 6 /* Maximum number of states in operation */
#define OPT_ANY 0xFFFFFFFF /* any chip supports this operation */
{OPT_ANY, {STATE_CMD_READID, STATE_ADDR_ZERO, STATE_DATAOUT_ID, STATE_READY}},
/* Large page devices read page */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART | ACTION_CPY,
- STATE_DATAOUT, STATE_READY}}
+ STATE_DATAOUT, STATE_READY}},
+ /* Large page devices random page read */
+ {OPT_LARGEPAGE, {STATE_CMD_RNDOUT, STATE_ADDR_COLUMN, STATE_CMD_RNDOUTSTART | ACTION_CPY,
+ STATE_DATAOUT, STATE_READY}},
};
struct weak_block {
if (ns->busw == 16)
NS_WARN("16-bit flashes support wasn't tested\n");
- printk("flash size: %llu MiB\n", ns->geom.totsz >> 20);
+ printk("flash size: %llu MiB\n",
+ (unsigned long long)ns->geom.totsz >> 20);
printk("page size: %u bytes\n", ns->geom.pgsz);
printk("OOB area size: %u bytes\n", ns->geom.oobsz);
printk("sector size: %u KiB\n", ns->geom.secsz >> 10);
printk("bus width: %u\n", ns->busw);
printk("bits in sector size: %u\n", ns->geom.secshift);
printk("bits in page size: %u\n", ns->geom.pgshift);
- printk("bits in OOB size: %u\n", ns->geom.oobshift);
- printk("flash size with OOB: %llu KiB\n", ns->geom.totszoob >> 10);
+ printk("bits in OOB size: %u\n", ns->geom.oobshift);
+ printk("flash size with OOB: %llu KiB\n",
+ (unsigned long long)ns->geom.totszoob >> 10);
printk("page address bytes: %u\n", ns->geom.pgaddrbytes);
printk("sector address bytes: %u\n", ns->geom.secaddrbytes);
printk("options: %#x\n", ns->options);
return "STATE_CMD_ERASE2";
case STATE_CMD_RESET:
return "STATE_CMD_RESET";
+ case STATE_CMD_RNDOUT:
+ return "STATE_CMD_RNDOUT";
+ case STATE_CMD_RNDOUTSTART:
+ return "STATE_CMD_RNDOUTSTART";
case STATE_ADDR_PAGE:
return "STATE_ADDR_PAGE";
case STATE_ADDR_SEC:
return "STATE_ADDR_SEC";
case STATE_ADDR_ZERO:
return "STATE_ADDR_ZERO";
+ case STATE_ADDR_COLUMN:
+ return "STATE_ADDR_COLUMN";
case STATE_DATAIN:
return "STATE_DATAIN";
case STATE_DATAOUT:
switch (cmd) {
case NAND_CMD_READ0:
+ case NAND_CMD_READ1:
case NAND_CMD_READSTART:
case NAND_CMD_PAGEPROG:
case NAND_CMD_READOOB:
case NAND_CMD_READID:
case NAND_CMD_ERASE2:
case NAND_CMD_RESET:
- case NAND_CMD_READ1:
+ case NAND_CMD_RNDOUT:
+ case NAND_CMD_RNDOUTSTART:
return 0;
case NAND_CMD_STATUS_MULTI:
return STATE_CMD_ERASE2;
case NAND_CMD_RESET:
return STATE_CMD_RESET;
+ case NAND_CMD_RNDOUT:
+ return STATE_CMD_RNDOUT;
+ case NAND_CMD_RNDOUTSTART:
+ return STATE_CMD_RNDOUTSTART;
}
NS_ERR("get_state_by_command: unknown command, BUG\n");
ns->regs.num = 1;
break;
+ case STATE_ADDR_COLUMN:
+ /* Column address is always 2 bytes */
+ ns->regs.num = ns->geom.pgaddrbytes - ns->geom.secaddrbytes;
+ break;
+
default:
NS_ERR("switch_state: BUG! unknown address state\n");
}
return;
}
- /*
- * Chip might still be in STATE_DATAOUT
- * (if OPT_AUTOINCR feature is supported), STATE_DATAOUT_STATUS or
- * STATE_DATAOUT_STATUS_M state. If so, switch state.
- */
+ /* Check that the command byte is correct */
+ if (check_command(byte)) {
+ NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
+ return;
+ }
+
if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS
|| NS_STATE(ns->state) == STATE_DATAOUT_STATUS_M
- || ((ns->options & OPT_AUTOINCR) && NS_STATE(ns->state) == STATE_DATAOUT))
+ || NS_STATE(ns->state) == STATE_DATAOUT) {
+ int row = ns->regs.row;
+
switch_state(ns);
+ if (byte == NAND_CMD_RNDOUT)
+ ns->regs.row = row;
+ }
/* Check if chip is expecting command */
if (NS_STATE(ns->nxstate) != STATE_UNKNOWN && !(ns->nxstate & STATE_CMD_MASK)) {
switch_to_ready_state(ns, NS_STATUS_FAILED(ns));
}
- /* Check that the command byte is correct */
- if (check_command(byte)) {
- NS_ERR("write_byte: unknown command %#x\n", (uint)byte);
- return;
- }
-
NS_DBG("command byte corresponding to %s state accepted\n",
get_state_name(get_state_by_command(byte)));
ns->regs.command = byte;
#include <linux/mtd/partitions.h>
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-orion/orion_nand.h>
#ifdef CONFIG_MTD_CMDLINE_PARTS
#include <linux/irq.h>
#include <asm/dma.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa3xx_nand.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa3xx_nand.h>
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
#include <linux/mtd/partitions.h>
#include <linux/interrupt.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
static void __iomem *sharpsl_io_base;
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <asm/sizes.h>
#include <asm/mach-types.h>
cfg_cmd->time_low = 0x00;
cfg_cmd->time_high = 0xf2;
cfg_cmd->promisc = 0;
- if (dev->flags & (IFF_ALLMULTI | IFF_PROMISC)) {
+ if (dev->flags & (IFF_ALLMULTI | IFF_PROMISC))
cfg_cmd->promisc = 1;
- dev->flags |= IFF_PROMISC;
- }
cfg_cmd->carr_coll = 0x00;
p->scb->cbl_offset = make16(cfg_cmd);
struct mc32_local *lp = netdev_priv(dev);
u16 filt = (1<<2); /* Save Bad Packets, for stats purposes */
- if (dev->flags&IFF_PROMISC)
+ if ((dev->flags&IFF_PROMISC) ||
+ (dev->flags&IFF_ALLMULTI) ||
+ dev->mc_count > 10)
/* Enable promiscuous mode */
filt |= 1;
- else if((dev->flags&IFF_ALLMULTI) || dev->mc_count > 10)
- {
- dev->flags|=IFF_PROMISC;
- filt |= 1;
- }
else if(dev->mc_count)
{
unsigned char block[62];
vp->rx_ring[i].next = cpu_to_le32(vp->rx_ring_dma + sizeof(struct boom_rx_desc) * (i+1));
vp->rx_ring[i].status = 0; /* Clear complete bit. */
vp->rx_ring[i].length = cpu_to_le32(PKT_BUF_SZ | LAST_FRAG);
- skb = dev_alloc_skb(PKT_BUF_SZ);
+
+ skb = __netdev_alloc_skb(dev, PKT_BUF_SZ + NET_IP_ALIGN,
+ GFP_KERNEL);
vp->rx_skbuff[i] = skb;
if (skb == NULL)
break; /* Bad news! */
- skb->dev = dev; /* Mark as being used by this device. */
- skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
+
+ skb_reserve(skb, NET_IP_ALIGN); /* Align IP on 16 byte boundaries */
vp->rx_ring[i].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, PKT_BUF_SZ, PCI_DMA_FROMDEVICE));
}
if (i != RX_RING_SIZE) {
struct sk_buff *skb;
entry = vp->dirty_rx % RX_RING_SIZE;
if (vp->rx_skbuff[entry] == NULL) {
- skb = dev_alloc_skb(PKT_BUF_SZ);
+ skb = netdev_alloc_skb(dev, PKT_BUF_SZ + NET_IP_ALIGN);
if (skb == NULL) {
static unsigned long last_jif;
if (time_after(jiffies, last_jif + 10 * HZ)) {
mod_timer(&vp->rx_oom_timer, RUN_AT(HZ * 1));
break; /* Bad news! */
}
- skb->dev = dev; /* Mark as being used by this device. */
- skb_reserve(skb, 2); /* Align IP on 16 byte boundaries */
+
+ skb_reserve(skb, NET_IP_ALIGN);
vp->rx_ring[entry].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, PKT_BUF_SZ, PCI_DMA_FROMDEVICE));
vp->rx_skbuff[entry] = skb;
}
{
return __ei_open(dev);
}
+EXPORT_SYMBOL(ei_open);
int ei_close(struct net_device *dev)
{
return __ei_close(dev);
}
+EXPORT_SYMBOL(ei_close);
irqreturn_t ei_interrupt(int irq, void *dev_id)
{
return __ei_interrupt(irq, dev_id);
}
+EXPORT_SYMBOL(ei_interrupt);
#ifdef CONFIG_NET_POLL_CONTROLLER
void ei_poll(struct net_device *dev)
{
__ei_poll(dev);
}
+EXPORT_SYMBOL(ei_poll);
#endif
struct net_device *__alloc_ei_netdev(int size)
{
return ____alloc_ei_netdev(size);
}
+EXPORT_SYMBOL(__alloc_ei_netdev);
void NS8390_init(struct net_device *dev, int startp)
{
__NS8390_init(dev, startp);
}
-
-EXPORT_SYMBOL(ei_open);
-EXPORT_SYMBOL(ei_close);
-EXPORT_SYMBOL(ei_interrupt);
-#ifdef CONFIG_NET_POLL_CONTROLLER
-EXPORT_SYMBOL(ei_poll);
-#endif
EXPORT_SYMBOL(NS8390_init);
-EXPORT_SYMBOL(__alloc_ei_netdev);
#if defined(MODULE)
"8390p.c:v1.10cvs 9/23/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n";
#define ei_inb(_p) inb(_p)
-#define ei_outb(_v,_p) outb(_v,_p)
+#define ei_outb(_v, _p) outb(_v, _p)
#define ei_inb_p(_p) inb_p(_p)
-#define ei_outb_p(_v,_p) outb_p(_v,_p)
+#define ei_outb_p(_v, _p) outb_p(_v, _p)
#include "lib8390.c"
{
return __ei_open(dev);
}
+EXPORT_SYMBOL(eip_open);
int eip_close(struct net_device *dev)
{
return __ei_close(dev);
}
+EXPORT_SYMBOL(eip_close);
irqreturn_t eip_interrupt(int irq, void *dev_id)
{
return __ei_interrupt(irq, dev_id);
}
+EXPORT_SYMBOL(eip_interrupt);
#ifdef CONFIG_NET_POLL_CONTROLLER
void eip_poll(struct net_device *dev)
{
__ei_poll(dev);
}
+EXPORT_SYMBOL(eip_poll);
#endif
struct net_device *__alloc_eip_netdev(int size)
{
return ____alloc_ei_netdev(size);
}
+EXPORT_SYMBOL(__alloc_eip_netdev);
void NS8390p_init(struct net_device *dev, int startp)
{
- return __NS8390_init(dev, startp);
+ __NS8390_init(dev, startp);
}
-
-EXPORT_SYMBOL(eip_open);
-EXPORT_SYMBOL(eip_close);
-EXPORT_SYMBOL(eip_interrupt);
-#ifdef CONFIG_NET_POLL_CONTROLLER
-EXPORT_SYMBOL(eip_poll);
-#endif
EXPORT_SYMBOL(NS8390p_init);
-EXPORT_SYMBOL(__alloc_eip_netdev);
#if defined(MODULE)
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
- (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712)
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
+ CPU_SUBTYPE_SH7619)
select CRC32
select MII
select MDIO_BITBANG
select PHYLIB
help
Renesas SuperH Ethernet device driver.
- This driver support SH7710 and SH7712.
+ This driver support SH7710, SH7712, SH7763 and SH7619.
config SUNLANCE
tristate "Sun LANCE support"
#include <linux/bitops.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/system.h>
#include <asm/uaccess.h>
#include <asm/mach-types.h>
-#include <asm/arch/at91rm9200_emac.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/board.h>
+#include <mach/at91rm9200_emac.h>
+#include <mach/gpio.h>
+#include <mach/board.h>
#include "at91_ether.h"
#include <linux/moduleparam.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
-#include <asm/arch/ep93xx-regs.h>
-#include <asm/arch/platform.h>
+#include <mach/ep93xx-regs.h>
+#include <mach/platform.h>
#include <asm/io.h>
#define DRV_MODULE_NAME "ep93xx-eth"
#include <linux/kernel.h>
#include <linux/mii.h>
#include <linux/platform_device.h>
-#include <asm/arch/npe.h>
-#include <asm/arch/qmgr.h>
+#include <mach/npe.h>
+#include <mach/qmgr.h>
#define DEBUG_QUEUES 0
#define DEBUG_DESC 0
{
struct pci_dev *pdev = adapter->pdev;
+ /*
+ * The L1 hardware contains a bug that erroneously sets the
+ * PACKET_FLAG_ERR and ERR_FLAG_L4_CHKSUM bits whenever a
+ * fragmented IP packet is received, even though the packet
+ * is perfectly valid and its checksum is correct. There's
+ * no way to distinguish between one of these good packets
+ * and a packet that actually contains a TCP/UDP checksum
+ * error, so all we can do is allow it to be handed up to
+ * the higher layers and let it be sorted out there.
+ */
+
skb->ip_summed = CHECKSUM_NONE;
if (unlikely(rrd->pkt_flg & PACKET_FLAG_ERR)) {
return;
}
- /* IPv4, but hardware thinks its checksum is wrong */
- if (netif_msg_rx_err(adapter))
- dev_printk(KERN_DEBUG, &pdev->dev,
- "hw csum wrong, pkt_flag:%x, err_flag:%x\n",
- rrd->pkt_flg, rrd->err_flg);
- skb->ip_summed = CHECKSUM_COMPLETE;
- skb->csum = htons(rrd->xsz.xsum_sz.rx_chksum);
- adapter->hw_csum_err++;
return;
}
struct net_local *lp = netdev_priv(dev);
long ioaddr = dev->base_addr;
- if ( dev->mc_count > 0 || (dev->flags & (IFF_ALLMULTI|IFF_PROMISC))) {
- /* We must make the kernel realise we had to move
- * into promisc mode or we start all out war on
- * the cable. - AC
- */
- dev->flags|=IFF_PROMISC;
+ if (dev->mc_count > 0 || (dev->flags & (IFF_ALLMULTI|IFF_PROMISC)))
lp->addr_mode = CMR2h_PROMISC;
- } else
+ else
lp->addr_mode = CMR2h_Normal;
write_reg_high(ioaddr, CMR2, lp->addr_mode);
}
static int bfin_mac_hard_start_xmit(struct sk_buff *skb,
struct net_device *dev)
{
- unsigned int data;
+ u16 *data;
current_tx_ptr->skb = skb;
- /*
- * Is skb->data always 16-bit aligned?
- * Do we need to memcpy((char *)(tail->packet + 2), skb->data, len)?
- */
- if ((((unsigned int)(skb->data)) & 0x02) == 2) {
- /* move skb->data to current_tx_ptr payload */
- data = (unsigned int)(skb->data) - 2;
- *((unsigned short *)data) = (unsigned short)(skb->len);
- current_tx_ptr->desc_a.start_addr = (unsigned long)data;
- /* this is important! */
- blackfin_dcache_flush_range(data, (data + (skb->len)) + 2);
-
+ if (ANOMALY_05000285) {
+ /*
+ * TXDWA feature is not avaible to older revision < 0.3 silicon
+ * of BF537
+ *
+ * Only if data buffer is ODD WORD alignment, we do not
+ * need to memcpy
+ */
+ u32 data_align = (u32)(skb->data) & 0x3;
+ if (data_align == 0x2) {
+ /* move skb->data to current_tx_ptr payload */
+ data = (u16 *)(skb->data) - 1;
+ *data = (u16)(skb->len);
+ current_tx_ptr->desc_a.start_addr = (u32)data;
+ /* this is important! */
+ blackfin_dcache_flush_range((u32)data,
+ (u32)((u8 *)data + skb->len + 4));
+ } else {
+ *((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len);
+ memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data,
+ skb->len);
+ current_tx_ptr->desc_a.start_addr =
+ (u32)current_tx_ptr->packet;
+ if (current_tx_ptr->status.status_word != 0)
+ current_tx_ptr->status.status_word = 0;
+ blackfin_dcache_flush_range(
+ (u32)current_tx_ptr->packet,
+ (u32)(current_tx_ptr->packet + skb->len + 2));
+ }
} else {
- *((unsigned short *)(current_tx_ptr->packet)) =
- (unsigned short)(skb->len);
- memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
- (skb->len));
- current_tx_ptr->desc_a.start_addr =
- (unsigned long)current_tx_ptr->packet;
- if (current_tx_ptr->status.status_word != 0)
- current_tx_ptr->status.status_word = 0;
- blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
- packet,
- (unsigned int)(current_tx_ptr->
- packet + skb->len) +
- 2);
+ /*
+ * TXDWA feature is avaible to revision < 0.3 silicon of
+ * BF537 and always avaible to BF52x
+ */
+ u32 data_align = (u32)(skb->data) & 0x3;
+ if (data_align == 0x0) {
+ u16 sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl |= TXDWA;
+ bfin_write_EMAC_SYSCTL(sysctl);
+
+ /* move skb->data to current_tx_ptr payload */
+ data = (u16 *)(skb->data) - 2;
+ *data = (u16)(skb->len);
+ current_tx_ptr->desc_a.start_addr = (u32)data;
+ /* this is important! */
+ blackfin_dcache_flush_range(
+ (u32)data,
+ (u32)((u8 *)data + skb->len + 4));
+ } else if (data_align == 0x2) {
+ u16 sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl &= ~TXDWA;
+ bfin_write_EMAC_SYSCTL(sysctl);
+
+ /* move skb->data to current_tx_ptr payload */
+ data = (u16 *)(skb->data) - 1;
+ *data = (u16)(skb->len);
+ current_tx_ptr->desc_a.start_addr = (u32)data;
+ /* this is important! */
+ blackfin_dcache_flush_range(
+ (u32)data,
+ (u32)((u8 *)data + skb->len + 4));
+ } else {
+ u16 sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl &= ~TXDWA;
+ bfin_write_EMAC_SYSCTL(sysctl);
+
+ *((u16 *)(current_tx_ptr->packet)) = (u16)(skb->len);
+ memcpy((u8 *)(current_tx_ptr->packet + 2), skb->data,
+ skb->len);
+ current_tx_ptr->desc_a.start_addr =
+ (u32)current_tx_ptr->packet;
+ if (current_tx_ptr->status.status_word != 0)
+ current_tx_ptr->status.status_word = 0;
+ blackfin_dcache_flush_range(
+ (u32)current_tx_ptr->packet,
+ (u32)(current_tx_ptr->packet + skb->len + 2));
+ }
}
/* enable this packet's dma */
(unsigned long)skb->tail);
dev->last_rx = jiffies;
- skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
#if defined(BFIN_MAC_CSUM_OFFLOAD)
skb->csum = current_rx_ptr->status.ip_payload_csum;
phy_start(lp->phydev);
phy_write(lp->phydev, MII_BMCR, BMCR_RESET);
setup_system_regs(dev);
+ setup_mac_addr(dev->dev_addr);
bfin_mac_disable();
bfin_mac_enable();
pr_debug("hardware init finished\n");
return 0;
}
-static int __init bfin_mac_probe(struct platform_device *pdev)
+static int __devinit bfin_mac_probe(struct platform_device *pdev)
{
struct net_device *ndev;
struct bfin_mac_local *lp;
return rc;
}
-static int bfin_mac_remove(struct platform_device *pdev)
+static int __devexit bfin_mac_remove(struct platform_device *pdev)
{
struct net_device *ndev = platform_get_drvdata(pdev);
struct bfin_mac_local *lp = netdev_priv(ndev);
static struct platform_driver bfin_mac_driver = {
.probe = bfin_mac_probe,
- .remove = bfin_mac_remove,
+ .remove = __devexit_p(bfin_mac_remove),
.resume = bfin_mac_resume,
.suspend = bfin_mac_suspend,
.driver = {
bp->link_params.req_flow_ctrl = (bp->port.link_config &
PORT_FEATURE_FLOW_CONTROL_MASK);
if ((bp->link_params.req_flow_ctrl == FLOW_CTRL_AUTO) &&
- (!bp->port.supported & SUPPORTED_Autoneg))
+ !(bp->port.supported & SUPPORTED_Autoneg))
bp->link_params.req_flow_ctrl = FLOW_CTRL_NONE;
BNX2X_DEV_INFO("req_line_speed %d req_duplex %d req_flow_ctrl 0x%x"
aggregator = __get_first_agg(port);
ad_agg_selection_logic(aggregator);
}
+ bond_3ad_set_carrier(bond);
}
// for each port run the state machines
/*-------------------------------- Monitoring -------------------------------*/
-/*
- * if !have_locks, return nonzero if a failover is necessary. if
- * have_locks, do whatever failover activities are needed.
- *
- * This is to separate the inspection and failover steps for locking
- * purposes; failover requires rtnl, but acquiring it for every
- * inspection is undesirable, so a wrapper first does inspection, and
- * the acquires the necessary locks and calls again to perform
- * failover if needed. Since all locks are dropped, a complete
- * restart is needed between calls.
- */
-static int __bond_mii_monitor(struct bonding *bond, int have_locks)
-{
- struct slave *slave, *oldcurrent;
- int do_failover = 0;
- int i;
-
- if (bond->slave_cnt == 0)
- goto out;
- /* we will try to read the link status of each of our slaves, and
- * set their IFF_RUNNING flag appropriately. For each slave not
- * supporting MII status, we won't do anything so that a user-space
- * program could monitor the link itself if needed.
- */
-
- read_lock(&bond->curr_slave_lock);
- oldcurrent = bond->curr_active_slave;
- read_unlock(&bond->curr_slave_lock);
+static int bond_miimon_inspect(struct bonding *bond)
+{
+ struct slave *slave;
+ int i, link_state, commit = 0;
bond_for_each_slave(bond, slave, i) {
- struct net_device *slave_dev = slave->dev;
- int link_state;
- u16 old_speed = slave->speed;
- u8 old_duplex = slave->duplex;
+ slave->new_link = BOND_LINK_NOCHANGE;
- link_state = bond_check_dev_link(bond, slave_dev, 0);
+ link_state = bond_check_dev_link(bond, slave->dev, 0);
switch (slave->link) {
- case BOND_LINK_UP: /* the link was up */
- if (link_state == BMSR_LSTATUS) {
- if (!oldcurrent) {
- if (!have_locks)
- return 1;
- do_failover = 1;
- }
- break;
- } else { /* link going down */
- slave->link = BOND_LINK_FAIL;
- slave->delay = bond->params.downdelay;
-
- if (slave->link_failure_count < UINT_MAX) {
- slave->link_failure_count++;
- }
+ case BOND_LINK_UP:
+ if (link_state)
+ continue;
- if (bond->params.downdelay) {
- printk(KERN_INFO DRV_NAME
- ": %s: link status down for %s "
- "interface %s, disabling it in "
- "%d ms.\n",
- bond->dev->name,
- IS_UP(slave_dev)
- ? ((bond->params.mode == BOND_MODE_ACTIVEBACKUP)
- ? ((slave == oldcurrent)
- ? "active " : "backup ")
- : "")
- : "idle ",
- slave_dev->name,
- bond->params.downdelay * bond->params.miimon);
- }
+ slave->link = BOND_LINK_FAIL;
+ slave->delay = bond->params.downdelay;
+ if (slave->delay) {
+ printk(KERN_INFO DRV_NAME
+ ": %s: link status down for %s"
+ "interface %s, disabling it in %d ms.\n",
+ bond->dev->name,
+ (bond->params.mode ==
+ BOND_MODE_ACTIVEBACKUP) ?
+ ((slave->state == BOND_STATE_ACTIVE) ?
+ "active " : "backup ") : "",
+ slave->dev->name,
+ bond->params.downdelay * bond->params.miimon);
}
- /* no break ! fall through the BOND_LINK_FAIL test to
- ensure proper action to be taken
- */
- case BOND_LINK_FAIL: /* the link has just gone down */
- if (link_state != BMSR_LSTATUS) {
- /* link stays down */
- if (slave->delay <= 0) {
- if (!have_locks)
- return 1;
-
- /* link down for too long time */
- slave->link = BOND_LINK_DOWN;
-
- /* in active/backup mode, we must
- * completely disable this interface
- */
- if ((bond->params.mode == BOND_MODE_ACTIVEBACKUP) ||
- (bond->params.mode == BOND_MODE_8023AD)) {
- bond_set_slave_inactive_flags(slave);
- }
-
- printk(KERN_INFO DRV_NAME
- ": %s: link status definitely "
- "down for interface %s, "
- "disabling it\n",
- bond->dev->name,
- slave_dev->name);
-
- /* notify ad that the link status has changed */
- if (bond->params.mode == BOND_MODE_8023AD) {
- bond_3ad_handle_link_change(slave, BOND_LINK_DOWN);
- }
-
- if ((bond->params.mode == BOND_MODE_TLB) ||
- (bond->params.mode == BOND_MODE_ALB)) {
- bond_alb_handle_link_change(bond, slave, BOND_LINK_DOWN);
- }
-
- if (slave == oldcurrent) {
- do_failover = 1;
- }
- } else {
- slave->delay--;
- }
- } else {
- /* link up again */
- slave->link = BOND_LINK_UP;
+ /*FALLTHRU*/
+ case BOND_LINK_FAIL:
+ if (link_state) {
+ /*
+ * recovered before downdelay expired
+ */
+ slave->link = BOND_LINK_UP;
slave->jiffies = jiffies;
printk(KERN_INFO DRV_NAME
": %s: link status up again after %d "
"ms for interface %s.\n",
bond->dev->name,
- (bond->params.downdelay - slave->delay) * bond->params.miimon,
- slave_dev->name);
+ (bond->params.downdelay - slave->delay) *
+ bond->params.miimon,
+ slave->dev->name);
+ continue;
}
- break;
- case BOND_LINK_DOWN: /* the link was down */
- if (link_state != BMSR_LSTATUS) {
- /* the link stays down, nothing more to do */
- break;
- } else { /* link going up */
- slave->link = BOND_LINK_BACK;
- slave->delay = bond->params.updelay;
- if (bond->params.updelay) {
- /* if updelay == 0, no need to
- advertise about a 0 ms delay */
- printk(KERN_INFO DRV_NAME
- ": %s: link status up for "
- "interface %s, enabling it "
- "in %d ms.\n",
- bond->dev->name,
- slave_dev->name,
- bond->params.updelay * bond->params.miimon);
- }
+ if (slave->delay <= 0) {
+ slave->new_link = BOND_LINK_DOWN;
+ commit++;
+ continue;
}
- /* no break ! fall through the BOND_LINK_BACK state in
- case there's something to do.
- */
- case BOND_LINK_BACK: /* the link has just come back */
- if (link_state != BMSR_LSTATUS) {
- /* link down again */
- slave->link = BOND_LINK_DOWN;
+ slave->delay--;
+ break;
+
+ case BOND_LINK_DOWN:
+ if (!link_state)
+ continue;
+
+ slave->link = BOND_LINK_BACK;
+ slave->delay = bond->params.updelay;
+
+ if (slave->delay) {
+ printk(KERN_INFO DRV_NAME
+ ": %s: link status up for "
+ "interface %s, enabling it in %d ms.\n",
+ bond->dev->name, slave->dev->name,
+ bond->params.updelay *
+ bond->params.miimon);
+ }
+ /*FALLTHRU*/
+ case BOND_LINK_BACK:
+ if (!link_state) {
+ slave->link = BOND_LINK_DOWN;
printk(KERN_INFO DRV_NAME
": %s: link status down again after %d "
"ms for interface %s.\n",
bond->dev->name,
- (bond->params.updelay - slave->delay) * bond->params.miimon,
- slave_dev->name);
- } else {
- /* link stays up */
- if (slave->delay == 0) {
- if (!have_locks)
- return 1;
-
- /* now the link has been up for long time enough */
- slave->link = BOND_LINK_UP;
- slave->jiffies = jiffies;
-
- if (bond->params.mode == BOND_MODE_8023AD) {
- /* prevent it from being the active one */
- slave->state = BOND_STATE_BACKUP;
- } else if (bond->params.mode != BOND_MODE_ACTIVEBACKUP) {
- /* make it immediately active */
- slave->state = BOND_STATE_ACTIVE;
- } else if (slave != bond->primary_slave) {
- /* prevent it from being the active one */
- slave->state = BOND_STATE_BACKUP;
- }
+ (bond->params.updelay - slave->delay) *
+ bond->params.miimon,
+ slave->dev->name);
- printk(KERN_INFO DRV_NAME
- ": %s: link status definitely "
- "up for interface %s.\n",
- bond->dev->name,
- slave_dev->name);
-
- /* notify ad that the link status has changed */
- if (bond->params.mode == BOND_MODE_8023AD) {
- bond_3ad_handle_link_change(slave, BOND_LINK_UP);
- }
-
- if ((bond->params.mode == BOND_MODE_TLB) ||
- (bond->params.mode == BOND_MODE_ALB)) {
- bond_alb_handle_link_change(bond, slave, BOND_LINK_UP);
- }
-
- if ((!oldcurrent) ||
- (slave == bond->primary_slave)) {
- do_failover = 1;
- }
- } else {
- slave->delay--;
- }
+ continue;
}
+
+ if (slave->delay <= 0) {
+ slave->new_link = BOND_LINK_UP;
+ commit++;
+ continue;
+ }
+
+ slave->delay--;
break;
- default:
- /* Should not happen */
- printk(KERN_ERR DRV_NAME
- ": %s: Error: %s Illegal value (link=%d)\n",
- bond->dev->name,
- slave->dev->name,
- slave->link);
- goto out;
- } /* end of switch (slave->link) */
+ }
+ }
- bond_update_speed_duplex(slave);
+ return commit;
+}
- if (bond->params.mode == BOND_MODE_8023AD) {
- if (old_speed != slave->speed) {
- bond_3ad_adapter_speed_changed(slave);
- }
+static void bond_miimon_commit(struct bonding *bond)
+{
+ struct slave *slave;
+ int i;
+
+ bond_for_each_slave(bond, slave, i) {
+ switch (slave->new_link) {
+ case BOND_LINK_NOCHANGE:
+ continue;
+
+ case BOND_LINK_UP:
+ slave->link = BOND_LINK_UP;
+ slave->jiffies = jiffies;
- if (old_duplex != slave->duplex) {
- bond_3ad_adapter_duplex_changed(slave);
+ if (bond->params.mode == BOND_MODE_8023AD) {
+ /* prevent it from being the active one */
+ slave->state = BOND_STATE_BACKUP;
+ } else if (bond->params.mode != BOND_MODE_ACTIVEBACKUP) {
+ /* make it immediately active */
+ slave->state = BOND_STATE_ACTIVE;
+ } else if (slave != bond->primary_slave) {
+ /* prevent it from being the active one */
+ slave->state = BOND_STATE_BACKUP;
}
- }
- } /* end of for */
+ printk(KERN_INFO DRV_NAME
+ ": %s: link status definitely "
+ "up for interface %s.\n",
+ bond->dev->name, slave->dev->name);
- if (do_failover) {
- ASSERT_RTNL();
+ /* notify ad that the link status has changed */
+ if (bond->params.mode == BOND_MODE_8023AD)
+ bond_3ad_handle_link_change(slave, BOND_LINK_UP);
- write_lock_bh(&bond->curr_slave_lock);
+ if ((bond->params.mode == BOND_MODE_TLB) ||
+ (bond->params.mode == BOND_MODE_ALB))
+ bond_alb_handle_link_change(bond, slave,
+ BOND_LINK_UP);
- bond_select_active_slave(bond);
+ if (!bond->curr_active_slave ||
+ (slave == bond->primary_slave))
+ goto do_failover;
- write_unlock_bh(&bond->curr_slave_lock);
+ continue;
- } else
- bond_set_carrier(bond);
+ case BOND_LINK_DOWN:
+ slave->link = BOND_LINK_DOWN;
-out:
- return 0;
+ if (bond->params.mode == BOND_MODE_ACTIVEBACKUP ||
+ bond->params.mode == BOND_MODE_8023AD)
+ bond_set_slave_inactive_flags(slave);
+
+ printk(KERN_INFO DRV_NAME
+ ": %s: link status definitely down for "
+ "interface %s, disabling it\n",
+ bond->dev->name, slave->dev->name);
+
+ if (bond->params.mode == BOND_MODE_8023AD)
+ bond_3ad_handle_link_change(slave,
+ BOND_LINK_DOWN);
+
+ if (bond->params.mode == BOND_MODE_TLB ||
+ bond->params.mode == BOND_MODE_ALB)
+ bond_alb_handle_link_change(bond, slave,
+ BOND_LINK_DOWN);
+
+ if (slave == bond->curr_active_slave)
+ goto do_failover;
+
+ continue;
+
+ default:
+ printk(KERN_ERR DRV_NAME
+ ": %s: invalid new link %d on slave %s\n",
+ bond->dev->name, slave->new_link,
+ slave->dev->name);
+ slave->new_link = BOND_LINK_NOCHANGE;
+
+ continue;
+ }
+
+do_failover:
+ ASSERT_RTNL();
+ write_lock_bh(&bond->curr_slave_lock);
+ bond_select_active_slave(bond);
+ write_unlock_bh(&bond->curr_slave_lock);
+ }
+
+ bond_set_carrier(bond);
}
/*
* bond_mii_monitor
*
* Really a wrapper that splits the mii monitor into two phases: an
- * inspection, then (if inspection indicates something needs to be
- * done) an acquisition of appropriate locks followed by another pass
- * to implement whatever link state changes are indicated.
+ * inspection, then (if inspection indicates something needs to be done)
+ * an acquisition of appropriate locks followed by a commit phase to
+ * implement whatever link state changes are indicated.
*/
void bond_mii_monitor(struct work_struct *work)
{
struct bonding *bond = container_of(work, struct bonding,
mii_work.work);
- unsigned long delay;
read_lock(&bond->lock);
- if (bond->kill_timers) {
- read_unlock(&bond->lock);
- return;
- }
+ if (bond->kill_timers)
+ goto out;
+
+ if (bond->slave_cnt == 0)
+ goto re_arm;
if (bond->send_grat_arp) {
read_lock(&bond->curr_slave_lock);
read_unlock(&bond->curr_slave_lock);
}
- if (__bond_mii_monitor(bond, 0)) {
+ if (bond_miimon_inspect(bond)) {
read_unlock(&bond->lock);
rtnl_lock();
read_lock(&bond->lock);
- __bond_mii_monitor(bond, 1);
+
+ bond_miimon_commit(bond);
+
read_unlock(&bond->lock);
rtnl_unlock(); /* might sleep, hold no other locks */
read_lock(&bond->lock);
}
- delay = msecs_to_jiffies(bond->params.miimon);
+re_arm:
+ if (bond->params.miimon)
+ queue_delayed_work(bond->wq, &bond->mii_work,
+ msecs_to_jiffies(bond->params.miimon));
+out:
read_unlock(&bond->lock);
- queue_delayed_work(bond->wq, &bond->mii_work, delay);
}
static __be32 bond_glean_dev_ip(struct net_device *dev)
if (dev) {
printk(KERN_INFO DRV_NAME ": %s: Removing slave %s\n",
bond->dev->name, dev->name);
- if (bond->setup_by_slave)
- res = bond_release_and_destroy(bond->dev, dev);
- else
res = bond_release(bond->dev, dev);
if (res) {
ret = res;
static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0};
#elif defined(CONFIG_ARCH_PNX010X)
#include <asm/irq.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#define CIRRUS_DEFAULT_BASE IO_ADDRESS(EXT_STATIC2_s0_BASE + 0x200000) /* = Physical address 0x48200000 */
#define CIRRUS_DEFAULT_IRQ VH_INTC_INT_NUM_CASCADED_INTERRUPT_1 /* Event inputs bank 1 - ID 35/bit 3 */
static unsigned int netcard_portlist[] __used __initdata = {CIRRUS_DEFAULT_BASE, 0};
SF_ERASE_SECTOR = 0xd8, /* erase sector */
FW_FLASH_BOOT_ADDR = 0x70000, /* start address of FW in flash */
- FW_VERS_ADDR = 0x77ffc, /* flash address holding FW version */
+ FW_VERS_ADDR = 0x7fffc, /* flash address holding FW version */
FW_MIN_SIZE = 8 /* at least version and csum */
};
{
if (dev->mc_count || dev->flags&(IFF_ALLMULTI|IFF_PROMISC))
{ /* Enable promiscuous mode */
- /*
- * We must make the kernel realise we had to move
- * into promisc mode or we start all out war on
- * the cable. - AC
- */
- dev->flags|=IFF_PROMISC;
-
de620_set_register(dev, W_TCR, (TCR_DEF & ~RXPBM) | RXALL);
}
else
for (i = 0; i < 6; i += 2)
dm9000_read_eeprom(db, i / 2, ndev->dev_addr+i);
+ if (!is_valid_ether_addr(ndev->dev_addr) && pdata != NULL) {
+ mac_src = "platform data";
+ memcpy(ndev->dev_addr, pdata->dev_addr, 6);
+ }
+
if (!is_valid_ether_addr(ndev->dev_addr)) {
/* try reading from mac */
struct e1000_info;
-#define ndev_printk(level, netdev, format, arg...) \
- printk(level "%s: " format, (netdev)->name, ## arg)
+#define e_printk(level, adapter, format, arg...) \
+ printk(level "%s: %s: " format, pci_name(adapter->pdev), \
+ adapter->netdev->name, ## arg)
#ifdef DEBUG
-#define ndev_dbg(netdev, format, arg...) \
- ndev_printk(KERN_DEBUG , netdev, format, ## arg)
+#define e_dbg(format, arg...) \
+ e_printk(KERN_DEBUG , adapter, format, ## arg)
#else
-#define ndev_dbg(netdev, format, arg...) do { (void)(netdev); } while (0)
+#define e_dbg(format, arg...) do { (void)(adapter); } while (0)
#endif
-#define ndev_err(netdev, format, arg...) \
- ndev_printk(KERN_ERR , netdev, format, ## arg)
-#define ndev_info(netdev, format, arg...) \
- ndev_printk(KERN_INFO , netdev, format, ## arg)
-#define ndev_warn(netdev, format, arg...) \
- ndev_printk(KERN_WARNING , netdev, format, ## arg)
-#define ndev_notice(netdev, format, arg...) \
- ndev_printk(KERN_NOTICE , netdev, format, ## arg)
+#define e_err(format, arg...) \
+ e_printk(KERN_ERR, adapter, format, ## arg)
+#define e_info(format, arg...) \
+ e_printk(KERN_INFO, adapter, format, ## arg)
+#define e_warn(format, arg...) \
+ e_printk(KERN_WARNING, adapter, format, ## arg)
+#define e_notice(format, arg...) \
+ e_printk(KERN_NOTICE, adapter, format, ## arg)
/* Tx/Rx descriptor defines */
unsigned long led_status;
unsigned int flags;
-
- /* for ioport free */
- int bars;
- int need_ioport;
};
struct e1000_info {
/* Fiber NICs only allow 1000 gbps Full duplex */
if ((adapter->hw.phy.media_type == e1000_media_type_fiber) &&
spddplx != (SPEED_1000 + DUPLEX_FULL)) {
- ndev_err(adapter->netdev, "Unsupported Speed/Duplex "
- "configuration\n");
+ e_err("Unsupported Speed/Duplex configuration\n");
return -EINVAL;
}
break;
case SPEED_1000 + DUPLEX_HALF: /* not supported */
default:
- ndev_err(adapter->netdev, "Unsupported Speed/Duplex "
- "configuration\n");
+ e_err("Unsupported Speed/Duplex configuration\n");
return -EINVAL;
}
return 0;
* cannot be changed
*/
if (e1000_check_reset_block(hw)) {
- ndev_err(netdev, "Cannot change link "
- "characteristics when SoL/IDER is active.\n");
+ e_err("Cannot change link characteristics when SoL/IDER is "
+ "active.\n");
return -EINVAL;
}
netdev->features &= ~NETIF_F_TSO6;
}
- ndev_info(netdev, "TSO is %s\n",
- data ? "Enabled" : "Disabled");
+ e_info("TSO is %s\n", data ? "Enabled" : "Disabled");
adapter->flags |= FLAG_TSO_FORCE;
return 0;
}
(test[pat] & write));
val = E1000_READ_REG_ARRAY(&adapter->hw, reg, offset);
if (val != (test[pat] & write & mask)) {
- ndev_err(adapter->netdev, "pattern test reg %04X "
- "failed: got 0x%08X expected 0x%08X\n",
- reg + offset,
- val, (test[pat] & write & mask));
+ e_err("pattern test reg %04X failed: got 0x%08X "
+ "expected 0x%08X\n", reg + offset, val,
+ (test[pat] & write & mask));
*data = reg;
return 1;
}
__ew32(&adapter->hw, reg, write & mask);
val = __er32(&adapter->hw, reg);
if ((write & mask) != (val & mask)) {
- ndev_err(adapter->netdev, "set/check reg %04X test failed: "
- "got 0x%08X expected 0x%08X\n", reg, (val & mask),
- (write & mask));
+ e_err("set/check reg %04X test failed: got 0x%08X "
+ "expected 0x%08X\n", reg, (val & mask), (write & mask));
*data = reg;
return 1;
}
{
struct e1000_hw *hw = &adapter->hw;
struct e1000_mac_info *mac = &adapter->hw.mac;
- struct net_device *netdev = adapter->netdev;
u32 value;
u32 before;
u32 after;
ew32(STATUS, toggle);
after = er32(STATUS) & toggle;
if (value != after) {
- ndev_err(netdev, "failed STATUS register test got: "
- "0x%08X expected: 0x%08X\n", after, value);
+ e_err("failed STATUS register test got: 0x%08X expected: "
+ "0x%08X\n", after, value);
*data = 1;
return 1;
}
*data = 1;
return -1;
}
- ndev_info(netdev, "testing %s interrupt\n",
- (shared_int ? "shared" : "unshared"));
+ e_info("testing %s interrupt\n", (shared_int ? "shared" : "unshared"));
/* Disable all the interrupts */
ew32(IMC, 0xFFFFFFFF);
* sessions are active
*/
if (e1000_check_reset_block(&adapter->hw)) {
- ndev_err(adapter->netdev, "Cannot do PHY loopback test "
- "when SoL/IDER is active.\n");
+ e_err("Cannot do PHY loopback test when SoL/IDER is active.\n");
*data = 0;
goto out;
}
forced_speed_duplex = adapter->hw.mac.forced_speed_duplex;
autoneg = adapter->hw.mac.autoneg;
- ndev_info(netdev, "offline testing starting\n");
+ e_info("offline testing starting\n");
/*
* Link test performed before hardware reset so autoneg doesn't
if (if_running)
dev_open(netdev);
} else {
- ndev_info(netdev, "online testing starting\n");
+ e_info("online testing starting\n");
/* Online tests */
if (e1000_link_test(adapter, &data[4]))
eth_test->flags |= ETH_TEST_FL_FAILED;
wol->supported &= ~WAKE_UCAST;
if (adapter->wol & E1000_WUFC_EX)
- ndev_err(netdev, "Interface does not support "
- "directed (unicast) frame wake-up packets\n");
+ e_err("Interface does not support directed (unicast) "
+ "frame wake-up packets\n");
}
if (adapter->wol & E1000_WUFC_EX)
* packet, also make sure the frame isn't just CRC only */
if (!(status & E1000_RXD_STAT_EOP) || (length <= 4)) {
/* All receives must fit into a single buffer */
- ndev_dbg(netdev, "%s: Receive packet consumed "
- "multiple buffers\n", netdev->name);
+ e_dbg("%s: Receive packet consumed multiple buffers\n",
+ netdev->name);
/* recycle */
buffer_info->skb = skb;
goto next_desc;
unsigned int i = tx_ring->next_to_clean;
unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
- struct net_device *netdev = adapter->netdev;
/* detected Tx unit hang */
- ndev_err(netdev,
- "Detected Tx Unit Hang:\n"
- " TDH <%x>\n"
- " TDT <%x>\n"
- " next_to_use <%x>\n"
- " next_to_clean <%x>\n"
- "buffer_info[next_to_clean]:\n"
- " time_stamp <%lx>\n"
- " next_to_watch <%x>\n"
- " jiffies <%lx>\n"
- " next_to_watch.status <%x>\n",
- readl(adapter->hw.hw_addr + tx_ring->head),
- readl(adapter->hw.hw_addr + tx_ring->tail),
- tx_ring->next_to_use,
- tx_ring->next_to_clean,
- tx_ring->buffer_info[eop].time_stamp,
- eop,
- jiffies,
- eop_desc->upper.fields.status);
+ e_err("Detected Tx Unit Hang:\n"
+ " TDH <%x>\n"
+ " TDT <%x>\n"
+ " next_to_use <%x>\n"
+ " next_to_clean <%x>\n"
+ "buffer_info[next_to_clean]:\n"
+ " time_stamp <%lx>\n"
+ " next_to_watch <%x>\n"
+ " jiffies <%lx>\n"
+ " next_to_watch.status <%x>\n",
+ readl(adapter->hw.hw_addr + tx_ring->head),
+ readl(adapter->hw.hw_addr + tx_ring->tail),
+ tx_ring->next_to_use,
+ tx_ring->next_to_clean,
+ tx_ring->buffer_info[eop].time_stamp,
+ eop,
+ jiffies,
+ eop_desc->upper.fields.status);
}
/**
buffer_info->dma = 0;
if (!(staterr & E1000_RXD_STAT_EOP)) {
- ndev_dbg(netdev, "%s: Packet Split buffers didn't pick "
- "up the full packet\n", netdev->name);
+ e_dbg("%s: Packet Split buffers didn't pick up the "
+ "full packet\n", netdev->name);
dev_kfree_skb_irq(skb);
goto next_desc;
}
length = le16_to_cpu(rx_desc->wb.middle.length0);
if (!length) {
- ndev_dbg(netdev, "%s: Last part of the packet spanning"
- " multiple descriptors\n", netdev->name);
+ e_dbg("%s: Last part of the packet spanning multiple "
+ "descriptors\n", netdev->name);
dev_kfree_skb_irq(skb);
goto next_desc;
}
/* eth type trans needs skb->data to point to something */
if (!pskb_may_pull(skb, ETH_HLEN)) {
- ndev_err(netdev, "pskb_may_pull failed.\n");
+ e_err("pskb_may_pull failed.\n");
dev_kfree_skb(skb);
goto next_desc;
}
err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
netdev);
if (err) {
- ndev_err(netdev,
- "Unable to allocate %s interrupt (return: %d)\n",
- adapter->flags & FLAG_MSI_ENABLED ? "MSI":"INTx",
- err);
+ e_err("Unable to allocate %s interrupt (return: %d)\n",
+ adapter->flags & FLAG_MSI_ENABLED ? "MSI":"INTx", err);
if (adapter->flags & FLAG_MSI_ENABLED)
pci_disable_msi(adapter->pdev);
}
return 0;
err:
vfree(tx_ring->buffer_info);
- ndev_err(adapter->netdev,
- "Unable to allocate memory for the transmit descriptor ring\n");
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
return err;
}
}
err:
vfree(rx_ring->buffer_info);
- ndev_err(adapter->netdev,
- "Unable to allocate memory for the transmit descriptor ring\n");
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
return err;
}
* For parts with AMT enabled, let the firmware know
* that the network interface is in control
*/
- if ((adapter->flags & FLAG_HAS_AMT) && e1000e_check_mng_mode(hw))
+ if (adapter->flags & FLAG_HAS_AMT)
e1000_get_hw_control(adapter);
ew32(WUC, 0);
if (mac->ops.init_hw(hw))
- ndev_err(adapter->netdev, "Hardware Error\n");
+ e_err("Hardware Error\n");
e1000_update_mng_vlan(adapter);
return 0;
err:
- ndev_err(netdev, "Unable to allocate memory for queues\n");
+ e_err("Unable to allocate memory for queues\n");
kfree(adapter->rx_ring);
kfree(adapter->tx_ring);
return -ENOMEM;
* If AMT is enabled, let the firmware know that the network
* interface is now open
*/
- if ((adapter->flags & FLAG_HAS_AMT) &&
- e1000e_check_mng_mode(&adapter->hw))
+ if (adapter->flags & FLAG_HAS_AMT)
e1000_get_hw_control(adapter);
/*
* If AMT is enabled, let the firmware know that the network
* interface is now closed
*/
- if ((adapter->flags & FLAG_HAS_AMT) &&
- e1000e_check_mng_mode(&adapter->hw))
+ if (adapter->flags & FLAG_HAS_AMT)
e1000_release_hw_control(adapter);
return 0;
ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
if (ret_val)
- ndev_warn(adapter->netdev,
- "Error reading PHY register\n");
+ e_warn("Error reading PHY register\n");
} else {
/*
* Do not read PHY registers if link is not up
static void e1000_print_link_info(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
- struct net_device *netdev = adapter->netdev;
u32 ctrl = er32(CTRL);
- ndev_info(netdev,
- "Link is Up %d Mbps %s, Flow Control: %s\n",
- adapter->link_speed,
- (adapter->link_duplex == FULL_DUPLEX) ?
- "Full Duplex" : "Half Duplex",
- ((ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE)) ?
- "RX/TX" :
- ((ctrl & E1000_CTRL_RFCE) ? "RX" :
- ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" )));
+ e_info("Link is Up %d Mbps %s, Flow Control: %s\n",
+ adapter->link_speed,
+ (adapter->link_duplex == FULL_DUPLEX) ?
+ "Full Duplex" : "Half Duplex",
+ ((ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE)) ?
+ "RX/TX" :
+ ((ctrl & E1000_CTRL_RFCE) ? "RX" :
+ ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" )));
}
static bool e1000_has_link(struct e1000_adapter *adapter)
if ((ret_val == E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
(er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
/* See e1000_kmrn_lock_loss_workaround_ich8lan() */
- ndev_info(adapter->netdev,
- "Gigabit has been disabled, downgrading speed\n");
+ e_info("Gigabit has been disabled, downgrading speed\n");
}
return link_active;
switch (adapter->link_speed) {
case SPEED_10:
case SPEED_100:
- ndev_info(netdev,
- "10/100 speed: disabling TSO\n");
+ e_info("10/100 speed: disabling TSO\n");
netdev->features &= ~NETIF_F_TSO;
netdev->features &= ~NETIF_F_TSO6;
break;
if (netif_carrier_ok(netdev)) {
adapter->link_speed = 0;
adapter->link_duplex = 0;
- ndev_info(netdev, "Link is Down\n");
+ e_info("Link is Down\n");
netif_carrier_off(netdev);
netif_tx_stop_all_queues(netdev);
if (!test_bit(__E1000_DOWN, &adapter->state))
pull_size = min((unsigned int)4, skb->data_len);
if (!__pskb_pull_tail(skb, pull_size)) {
- ndev_err(netdev,
- "__pskb_pull_tail failed.\n");
+ e_err("__pskb_pull_tail failed.\n");
dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
}
if ((max_frame < ETH_ZLEN + ETH_FCS_LEN) ||
(max_frame > MAX_JUMBO_FRAME_SIZE)) {
- ndev_err(netdev, "Invalid MTU setting\n");
+ e_err("Invalid MTU setting\n");
return -EINVAL;
}
/* Jumbo frame size limits */
if (max_frame > ETH_FRAME_LEN + ETH_FCS_LEN) {
if (!(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
- ndev_err(netdev, "Jumbo Frames not supported.\n");
+ e_err("Jumbo Frames not supported.\n");
return -EINVAL;
}
if (adapter->hw.phy.type == e1000_phy_ife) {
- ndev_err(netdev, "Jumbo Frames not supported.\n");
+ e_err("Jumbo Frames not supported.\n");
return -EINVAL;
}
}
#define MAX_STD_JUMBO_FRAME_SIZE 9234
if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
- ndev_err(netdev, "MTU > 9216 not supported.\n");
+ e_err("MTU > 9216 not supported.\n");
return -EINVAL;
}
adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
+ ETH_FCS_LEN;
- ndev_info(netdev, "changing MTU from %d to %d\n",
- netdev->mtu, new_mtu);
+ e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
netdev->mtu = new_mtu;
if (netif_running(netdev))
pci_restore_state(pdev);
e1000e_disable_l1aspm(pdev);
- if (adapter->need_ioport)
- err = pci_enable_device(pdev);
- else
- err = pci_enable_device_mem(pdev);
+ err = pci_enable_device_mem(pdev);
if (err) {
dev_err(&pdev->dev,
"Cannot enable PCI device from suspend\n");
* is up. For all other cases, let the f/w know that the h/w is now
* under the control of the driver.
*/
- if (!(adapter->flags & FLAG_HAS_AMT) || !e1000e_check_mng_mode(&adapter->hw))
+ if (!(adapter->flags & FLAG_HAS_AMT))
e1000_get_hw_control(adapter);
return 0;
int err;
e1000e_disable_l1aspm(pdev);
- if (adapter->need_ioport)
- err = pci_enable_device(pdev);
- else
- err = pci_enable_device_mem(pdev);
+ err = pci_enable_device_mem(pdev);
if (err) {
dev_err(&pdev->dev,
"Cannot re-enable PCI device after reset.\n");
* is up. For all other cases, let the f/w know that the h/w is now
* under the control of the driver.
*/
- if (!(adapter->flags & FLAG_HAS_AMT) ||
- !e1000e_check_mng_mode(&adapter->hw))
+ if (!(adapter->flags & FLAG_HAS_AMT))
e1000_get_hw_control(adapter);
}
u32 pba_num;
/* print bus type/speed/width info */
- ndev_info(netdev, "(PCI Express:2.5GB/s:%s) "
- "%02x:%02x:%02x:%02x:%02x:%02x\n",
- /* bus width */
- ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
- "Width x1"),
- /* MAC address */
- netdev->dev_addr[0], netdev->dev_addr[1],
- netdev->dev_addr[2], netdev->dev_addr[3],
- netdev->dev_addr[4], netdev->dev_addr[5]);
- ndev_info(netdev, "Intel(R) PRO/%s Network Connection\n",
- (hw->phy.type == e1000_phy_ife)
- ? "10/100" : "1000");
+ e_info("(PCI Express:2.5GB/s:%s) %02x:%02x:%02x:%02x:%02x:%02x\n",
+ /* bus width */
+ ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
+ "Width x1"),
+ /* MAC address */
+ netdev->dev_addr[0], netdev->dev_addr[1],
+ netdev->dev_addr[2], netdev->dev_addr[3],
+ netdev->dev_addr[4], netdev->dev_addr[5]);
+ e_info("Intel(R) PRO/%s Network Connection\n",
+ (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000");
e1000e_read_pba_num(hw, &pba_num);
- ndev_info(netdev, "MAC: %d, PHY: %d, PBA No: %06x-%03x\n",
- hw->mac.type, hw->phy.type,
- (pba_num >> 8), (pba_num & 0xff));
+ e_info("MAC: %d, PHY: %d, PBA No: %06x-%03x\n",
+ hw->mac.type, hw->phy.type, (pba_num >> 8), (pba_num & 0xff));
}
-/**
- * e1000e_is_need_ioport - determine if an adapter needs ioport resources or not
- * @pdev: PCI device information struct
- *
- * Returns true if an adapters needs ioport resources
- **/
-static int e1000e_is_need_ioport(struct pci_dev *pdev)
+static void e1000_eeprom_checks(struct e1000_adapter *adapter)
{
- switch (pdev->device) {
- /* Currently there are no adapters that need ioport resources */
- default:
- return false;
+ struct e1000_hw *hw = &adapter->hw;
+ int ret_val;
+ u16 buf = 0;
+
+ if (hw->mac.type != e1000_82573)
+ return;
+
+ ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf);
+ if (!(le16_to_cpu(buf) & (1 << 0))) {
+ /* Deep Smart Power Down (DSPD) */
+ e_warn("Warning: detected DSPD enabled in EEPROM\n");
+ }
+
+ ret_val = e1000_read_nvm(hw, NVM_INIT_3GIO_3, 1, &buf);
+ if (le16_to_cpu(buf) & (3 << 2)) {
+ /* ASPM enable */
+ e_warn("Warning: detected ASPM enabled in EEPROM\n");
}
}
int i, err, pci_using_dac;
u16 eeprom_data = 0;
u16 eeprom_apme_mask = E1000_EEPROM_APME;
- int bars, need_ioport;
e1000e_disable_l1aspm(pdev);
- /* do not allocate ioport bars when not needed */
- need_ioport = e1000e_is_need_ioport(pdev);
- if (need_ioport) {
- bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
- err = pci_enable_device(pdev);
- } else {
- bars = pci_select_bars(pdev, IORESOURCE_MEM);
- err = pci_enable_device_mem(pdev);
- }
+ err = pci_enable_device_mem(pdev);
if (err)
return err;
}
}
- err = pci_request_selected_regions(pdev, bars, e1000e_driver_name);
+ err = pci_request_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM),
+ e1000e_driver_name);
if (err)
goto err_pci_reg;
adapter->hw.adapter = adapter;
adapter->hw.mac.type = ei->mac;
adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1;
- adapter->bars = bars;
- adapter->need_ioport = need_ioport;
mmio_start = pci_resource_start(pdev, 0);
mmio_len = pci_resource_len(pdev, 0);
}
if (e1000_check_reset_block(&adapter->hw))
- ndev_info(netdev,
- "PHY reset is blocked due to SOL/IDER session.\n");
+ e_info("PHY reset is blocked due to SOL/IDER session.\n");
netdev->features = NETIF_F_SG |
NETIF_F_HW_CSUM |
if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
break;
if (i == 2) {
- ndev_err(netdev, "The NVM Checksum Is Not Valid\n");
+ e_err("The NVM Checksum Is Not Valid\n");
err = -EIO;
goto err_eeprom;
}
}
+ e1000_eeprom_checks(adapter);
+
/* copy the MAC address out of the NVM */
if (e1000e_read_mac_addr(&adapter->hw))
- ndev_err(netdev, "NVM Read Error while reading MAC address\n");
+ e_err("NVM Read Error while reading MAC address\n");
memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
if (!is_valid_ether_addr(netdev->perm_addr)) {
- ndev_err(netdev, "Invalid MAC Address: "
- "%02x:%02x:%02x:%02x:%02x:%02x\n",
- netdev->perm_addr[0], netdev->perm_addr[1],
- netdev->perm_addr[2], netdev->perm_addr[3],
- netdev->perm_addr[4], netdev->perm_addr[5]);
+ e_err("Invalid MAC Address: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ netdev->perm_addr[0], netdev->perm_addr[1],
+ netdev->perm_addr[2], netdev->perm_addr[3],
+ netdev->perm_addr[4], netdev->perm_addr[5]);
err = -EIO;
goto err_eeprom;
}
* is up. For all other cases, let the f/w know that the h/w is now
* under the control of the driver.
*/
- if (!(adapter->flags & FLAG_HAS_AMT) ||
- !e1000e_check_mng_mode(&adapter->hw))
+ if (!(adapter->flags & FLAG_HAS_AMT))
e1000_get_hw_control(adapter);
/* tell the stack to leave us alone until e1000_open() is called */
return 0;
err_register:
-err_hw_init:
- e1000_release_hw_control(adapter);
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_release_hw_control(adapter);
err_eeprom:
if (!e1000_check_reset_block(&adapter->hw))
e1000_phy_hw_reset(&adapter->hw);
+err_hw_init:
- if (adapter->hw.flash_address)
- iounmap(adapter->hw.flash_address);
-
-err_flashmap:
kfree(adapter->tx_ring);
kfree(adapter->rx_ring);
err_sw_init:
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+err_flashmap:
iounmap(adapter->hw.hw_addr);
err_ioremap:
free_netdev(netdev);
err_alloc_etherdev:
- pci_release_selected_regions(pdev, bars);
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
err_pci_reg:
err_dma:
pci_disable_device(pdev);
iounmap(adapter->hw.hw_addr);
if (adapter->hw.flash_address)
iounmap(adapter->hw.flash_address);
- pci_release_selected_regions(pdev, adapter->bars);
+ pci_release_selected_regions(pdev,
+ pci_select_bars(pdev, IORESOURCE_MEM));
free_netdev(netdev);
*******************************************************************************/
#include <linux/netdevice.h>
+#include <linux/pci.h>
#include "e1000.h"
case enable_option:
switch (*value) {
case OPTION_ENABLED:
- ndev_info(adapter->netdev, "%s Enabled\n", opt->name);
+ e_info("%s Enabled\n", opt->name);
return 0;
case OPTION_DISABLED:
- ndev_info(adapter->netdev, "%s Disabled\n", opt->name);
+ e_info("%s Disabled\n", opt->name);
return 0;
}
break;
case range_option:
if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
- ndev_info(adapter->netdev,
- "%s set to %i\n", opt->name, *value);
+ e_info("%s set to %i\n", opt->name, *value);
return 0;
}
break;
ent = &opt->arg.l.p[i];
if (*value == ent->i) {
if (ent->str[0] != '\0')
- ndev_info(adapter->netdev, "%s\n",
- ent->str);
+ e_info("%s\n", ent->str);
return 0;
}
}
BUG();
}
- ndev_info(adapter->netdev, "Invalid %s value specified (%i) %s\n",
- opt->name, *value, opt->err);
+ e_info("Invalid %s value specified (%i) %s\n", opt->name, *value,
+ opt->err);
*value = opt->def;
return -1;
}
void __devinit e1000e_check_options(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
- struct net_device *netdev = adapter->netdev;
int bd = adapter->bd_number;
if (bd >= E1000_MAX_NIC) {
- ndev_notice(netdev,
- "Warning: no configuration for board #%i\n", bd);
- ndev_notice(netdev, "Using defaults for all values\n");
+ e_notice("Warning: no configuration for board #%i\n", bd);
+ e_notice("Using defaults for all values\n");
}
{ /* Transmit Interrupt Delay */
adapter->itr = InterruptThrottleRate[bd];
switch (adapter->itr) {
case 0:
- ndev_info(netdev, "%s turned off\n",
- opt.name);
+ e_info("%s turned off\n", opt.name);
break;
case 1:
- ndev_info(netdev,
- "%s set to dynamic mode\n",
- opt.name);
+ e_info("%s set to dynamic mode\n", opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
break;
case 3:
- ndev_info(netdev,
- "%s set to dynamic conservative mode\n",
+ e_info("%s set to dynamic conservative mode\n",
opt.name);
adapter->itr_setting = adapter->itr;
adapter->itr = 20000;
if (dev->flags&(IFF_ALLMULTI|IFF_PROMISC) || dev->mc_count > 63)
{
- /*
- * We must make the kernel realise we had to move
- * into promisc mode or we start all out war on
- * the cable. If it was a promisc request the
- * flag is already set. If not we assert it.
- */
- dev->flags|=IFF_PROMISC;
-
eepro_sw2bank2(ioaddr); /* be CAREFUL, BANK 2 now */
mode = inb(ioaddr + REG2);
outb(mode | PRMSC_Mode, ioaddr + REG2);
}
}
}
- mutex_unlock(&dlpar_mem_lock);
- ehea_info("re-initializing driver complete");
+ ehea_info("re-initializing driver complete");
out:
+ mutex_unlock(&dlpar_mem_lock);
return;
}
random_ether_addr(dev->dev_addr);
enc28j60_set_hw_macaddr(dev);
- ret = request_irq(spi->irq, enc28j60_irq, IRQF_TRIGGER_FALLING,
- DRV_NAME, priv);
+ /* Board setup must set the relevant edge trigger type;
+ * level triggers won't currently work.
+ */
+ ret = request_irq(spi->irq, enc28j60_irq, 0, DRV_NAME, priv);
if (ret < 0) {
if (netif_msg_probe(priv))
dev_err(&spi->dev, DRV_NAME ": request irq %d failed "
if(dev->mc_count || dev->flags&(IFF_ALLMULTI|IFF_PROMISC))
{
- dev->flags|=IFF_PROMISC; /* Must do this */
outb(3, ioaddr + RECEIVE_MODE_REG);
} else {
outb(2, ioaddr + RECEIVE_MODE_REG);
* Hardware access:
*/
-#define DEV_NEED_TIMERIRQ 0x00001 /* set the timer irq flag in the irq mask */
-#define DEV_NEED_LINKTIMER 0x00002 /* poll link settings. Relies on the timer irq */
-#define DEV_HAS_LARGEDESC 0x00004 /* device supports jumbo frames and needs packet format 2 */
-#define DEV_HAS_HIGH_DMA 0x00008 /* device supports 64bit dma */
-#define DEV_HAS_CHECKSUM 0x00010 /* device supports tx and rx checksum offloads */
-#define DEV_HAS_VLAN 0x00020 /* device supports vlan tagging and striping */
-#define DEV_HAS_MSI 0x00040 /* device supports MSI */
-#define DEV_HAS_MSI_X 0x00080 /* device supports MSI-X */
-#define DEV_HAS_POWER_CNTRL 0x00100 /* device supports power savings */
-#define DEV_HAS_STATISTICS_V1 0x00200 /* device supports hw statistics version 1 */
-#define DEV_HAS_STATISTICS_V2 0x00400 /* device supports hw statistics version 2 */
-#define DEV_HAS_TEST_EXTENDED 0x00800 /* device supports extended diagnostic test */
-#define DEV_HAS_MGMT_UNIT 0x01000 /* device supports management unit */
-#define DEV_HAS_CORRECT_MACADDR 0x02000 /* device supports correct mac address order */
-#define DEV_HAS_COLLISION_FIX 0x04000 /* device supports tx collision fix */
-#define DEV_HAS_PAUSEFRAME_TX_V1 0x08000 /* device supports tx pause frames version 1 */
-#define DEV_HAS_PAUSEFRAME_TX_V2 0x10000 /* device supports tx pause frames version 2 */
-#define DEV_HAS_PAUSEFRAME_TX_V3 0x20000 /* device supports tx pause frames version 3 */
-#define DEV_NEED_TX_LIMIT 0x40000 /* device needs to limit tx */
-#define DEV_HAS_GEAR_MODE 0x80000 /* device supports gear mode */
+#define DEV_NEED_TIMERIRQ 0x000001 /* set the timer irq flag in the irq mask */
+#define DEV_NEED_LINKTIMER 0x000002 /* poll link settings. Relies on the timer irq */
+#define DEV_HAS_LARGEDESC 0x000004 /* device supports jumbo frames and needs packet format 2 */
+#define DEV_HAS_HIGH_DMA 0x000008 /* device supports 64bit dma */
+#define DEV_HAS_CHECKSUM 0x000010 /* device supports tx and rx checksum offloads */
+#define DEV_HAS_VLAN 0x000020 /* device supports vlan tagging and striping */
+#define DEV_HAS_MSI 0x000040 /* device supports MSI */
+#define DEV_HAS_MSI_X 0x000080 /* device supports MSI-X */
+#define DEV_HAS_POWER_CNTRL 0x000100 /* device supports power savings */
+#define DEV_HAS_STATISTICS_V1 0x000200 /* device supports hw statistics version 1 */
+#define DEV_HAS_STATISTICS_V2 0x000400 /* device supports hw statistics version 2 */
+#define DEV_HAS_STATISTICS_V3 0x000800 /* device supports hw statistics version 3 */
+#define DEV_HAS_TEST_EXTENDED 0x001000 /* device supports extended diagnostic test */
+#define DEV_HAS_MGMT_UNIT 0x002000 /* device supports management unit */
+#define DEV_HAS_CORRECT_MACADDR 0x004000 /* device supports correct mac address order */
+#define DEV_HAS_COLLISION_FIX 0x008000 /* device supports tx collision fix */
+#define DEV_HAS_PAUSEFRAME_TX_V1 0x010000 /* device supports tx pause frames version 1 */
+#define DEV_HAS_PAUSEFRAME_TX_V2 0x020000 /* device supports tx pause frames version 2 */
+#define DEV_HAS_PAUSEFRAME_TX_V3 0x040000 /* device supports tx pause frames version 3 */
+#define DEV_NEED_TX_LIMIT 0x080000 /* device needs to limit tx */
+#define DEV_HAS_GEAR_MODE 0x100000 /* device supports gear mode */
enum {
NvRegIrqStatus = 0x000,
#define NVREG_TX_PAUSEFRAME_ENABLE_V1 0x01800010
#define NVREG_TX_PAUSEFRAME_ENABLE_V2 0x056003f0
#define NVREG_TX_PAUSEFRAME_ENABLE_V3 0x09f00880
+ NvRegTxPauseFrameLimit = 0x174,
+#define NVREG_TX_PAUSEFRAMELIMIT_ENABLE 0x00010000
NvRegMIIStatus = 0x180,
#define NVREG_MIISTAT_ERROR 0x0001
#define NVREG_MIISTAT_LINKCHANGE 0x0008
#define NVREG_MIICTL_WRITE 0x00400
#define NVREG_MIICTL_ADDRSHIFT 5
NvRegMIIData = 0x194,
+ NvRegTxUnicast = 0x1a0,
+ NvRegTxMulticast = 0x1a4,
+ NvRegTxBroadcast = 0x1a8,
NvRegWakeUpFlags = 0x200,
#define NVREG_WAKEUPFLAGS_VAL 0x7770
#define NVREG_WAKEUPFLAGS_BUSYSHIFT 24
NvRegPowerState2 = 0x600,
#define NVREG_POWERSTATE2_POWERUP_MASK 0x0F11
#define NVREG_POWERSTATE2_POWERUP_REV_A3 0x0001
+#define NVREG_POWERSTATE2_PHY_RESET 0x0004
};
/* Big endian: should work, but is untested */
#define NV_RX_FRAMINGERR (1<<29)
#define NV_RX_ERROR (1<<30)
#define NV_RX_AVAIL (1<<31)
+#define NV_RX_ERROR_MASK (NV_RX_ERROR1|NV_RX_ERROR2|NV_RX_ERROR3|NV_RX_ERROR4|NV_RX_CRCERR|NV_RX_OVERFLOW|NV_RX_FRAMINGERR)
#define NV_RX2_CHECKSUMMASK (0x1C000000)
#define NV_RX2_CHECKSUM_IP (0x10000000)
/* error and avail are the same for both */
#define NV_RX2_ERROR (1<<30)
#define NV_RX2_AVAIL (1<<31)
+#define NV_RX2_ERROR_MASK (NV_RX2_ERROR1|NV_RX2_ERROR2|NV_RX2_ERROR3|NV_RX2_ERROR4|NV_RX2_CRCERR|NV_RX2_OVERFLOW|NV_RX2_FRAMINGERR)
#define NV_RX3_VLAN_TAG_PRESENT (1<<16)
#define NV_RX3_VLAN_TAG_MASK (0x0000FFFF)
#define PHY_REALTEK_INIT_REG4 0x14
#define PHY_REALTEK_INIT_REG5 0x18
#define PHY_REALTEK_INIT_REG6 0x11
+#define PHY_REALTEK_INIT_REG7 0x01
#define PHY_REALTEK_INIT1 0x0000
#define PHY_REALTEK_INIT2 0x8e00
#define PHY_REALTEK_INIT3 0x0001
#define PHY_REALTEK_INIT6 0xf5c7
#define PHY_REALTEK_INIT7 0x1000
#define PHY_REALTEK_INIT8 0x0003
+#define PHY_REALTEK_INIT9 0x0008
+#define PHY_REALTEK_INIT10 0x0005
+#define PHY_REALTEK_INIT11 0x0200
#define PHY_REALTEK_INIT_MSK1 0x0003
#define PHY_GIGABIT 0x0100
{ "rx_bytes" },
{ "tx_pause" },
{ "rx_pause" },
- { "rx_drop_frame" }
+ { "rx_drop_frame" },
+
+ /* version 3 stats */
+ { "tx_unicast" },
+ { "tx_multicast" },
+ { "tx_broadcast" }
};
struct nv_ethtool_stats {
u64 tx_pause;
u64 rx_pause;
u64 rx_drop_frame;
+
+ /* version 3 stats */
+ u64 tx_unicast;
+ u64 tx_multicast;
+ u64 tx_broadcast;
};
-#define NV_DEV_STATISTICS_V2_COUNT (sizeof(struct nv_ethtool_stats)/sizeof(u64))
+#define NV_DEV_STATISTICS_V3_COUNT (sizeof(struct nv_ethtool_stats)/sizeof(u64))
+#define NV_DEV_STATISTICS_V2_COUNT (NV_DEV_STATISTICS_V3_COUNT - 3)
#define NV_DEV_STATISTICS_V1_COUNT (NV_DEV_STATISTICS_V2_COUNT - 6)
/* diagnostics */
return PHY_ERROR;
}
}
+ if (np->phy_model == PHY_MODEL_REALTEK_8211 &&
+ np->phy_rev == PHY_REV_REALTEK_8211C) {
+ u32 powerstate = readl(base + NvRegPowerState2);
+
+ /* need to perform hw phy reset */
+ powerstate |= NVREG_POWERSTATE2_PHY_RESET;
+ writel(powerstate, base + NvRegPowerState2);
+ msleep(25);
+
+ powerstate &= ~NVREG_POWERSTATE2_PHY_RESET;
+ writel(powerstate, base + NvRegPowerState2);
+ msleep(25);
+
+ reg = mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG6, MII_READ);
+ reg |= PHY_REALTEK_INIT9;
+ if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG6, reg)) {
+ printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
+ if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG1, PHY_REALTEK_INIT10)) {
+ printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
+ reg = mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG7, MII_READ);
+ if (!(reg & PHY_REALTEK_INIT11)) {
+ reg |= PHY_REALTEK_INIT11;
+ if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG7, reg)) {
+ printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
+ }
+ if (mii_rw(dev, np->phyaddr, PHY_REALTEK_INIT_REG1, PHY_REALTEK_INIT1)) {
+ printk(KERN_INFO "%s: phy init failed.\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
+ }
if (np->phy_model == PHY_MODEL_REALTEK_8201) {
if (np->device_id == PCI_DEVICE_ID_NVIDIA_NVENET_32 ||
np->device_id == PCI_DEVICE_ID_NVIDIA_NVENET_33 ||
mii_control = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
mii_control |= BMCR_ANENABLE;
- /* reset the phy
- * (certain phys need bmcr to be setup with reset)
- */
- if (phy_reset(dev, mii_control)) {
- printk(KERN_INFO "%s: phy reset failed\n", pci_name(np->pci_dev));
- return PHY_ERROR;
+ if (np->phy_oui == PHY_OUI_REALTEK &&
+ np->phy_model == PHY_MODEL_REALTEK_8211 &&
+ np->phy_rev == PHY_REV_REALTEK_8211C) {
+ /* start autoneg since we already performed hw reset above */
+ mii_control |= BMCR_ANRESTART;
+ if (mii_rw(dev, np->phyaddr, MII_BMCR, mii_control)) {
+ printk(KERN_INFO "%s: phy init failed\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
+ } else {
+ /* reset the phy
+ * (certain phys need bmcr to be setup with reset)
+ */
+ if (phy_reset(dev, mii_control)) {
+ printk(KERN_INFO "%s: phy reset failed\n", pci_name(np->pci_dev));
+ return PHY_ERROR;
+ }
}
/* phy vendor specific configuration */
np->estats.rx_pause += readl(base + NvRegRxPause);
np->estats.rx_drop_frame += readl(base + NvRegRxDropFrame);
}
+
+ if (np->driver_data & DEV_HAS_STATISTICS_V3) {
+ np->estats.tx_unicast += readl(base + NvRegTxUnicast);
+ np->estats.tx_multicast += readl(base + NvRegTxMulticast);
+ np->estats.tx_broadcast += readl(base + NvRegTxBroadcast);
+ }
}
/*
struct fe_priv *np = netdev_priv(dev);
/* If the nic supports hw counters then retrieve latest values */
- if (np->driver_data & (DEV_HAS_STATISTICS_V1|DEV_HAS_STATISTICS_V2)) {
+ if (np->driver_data & (DEV_HAS_STATISTICS_V1|DEV_HAS_STATISTICS_V2|DEV_HAS_STATISTICS_V3)) {
nv_get_hw_stats(dev);
/* copy to net_device stats */
if (likely(flags & NV_RX_DESCRIPTORVALID)) {
len = flags & LEN_MASK_V1;
if (unlikely(flags & NV_RX_ERROR)) {
- if (flags & NV_RX_ERROR4) {
+ if ((flags & NV_RX_ERROR_MASK) == NV_RX_ERROR4) {
len = nv_getlen(dev, skb->data, len);
if (len < 0) {
dev->stats.rx_errors++;
}
}
/* framing errors are soft errors */
- else if (flags & NV_RX_FRAMINGERR) {
+ else if ((flags & NV_RX_ERROR_MASK) == NV_RX_FRAMINGERR) {
if (flags & NV_RX_SUBSTRACT1) {
len--;
}
if (likely(flags & NV_RX2_DESCRIPTORVALID)) {
len = flags & LEN_MASK_V2;
if (unlikely(flags & NV_RX2_ERROR)) {
- if (flags & NV_RX2_ERROR4) {
+ if ((flags & NV_RX2_ERROR_MASK) == NV_RX2_ERROR4) {
len = nv_getlen(dev, skb->data, len);
if (len < 0) {
dev->stats.rx_errors++;
}
}
/* framing errors are soft errors */
- else if (flags & NV_RX2_FRAMINGERR) {
+ else if ((flags & NV_RX2_ERROR_MASK) == NV_RX2_FRAMINGERR) {
if (flags & NV_RX2_SUBSTRACT1) {
len--;
}
if (likely(flags & NV_RX2_DESCRIPTORVALID)) {
len = flags & LEN_MASK_V2;
if (unlikely(flags & NV_RX2_ERROR)) {
- if (flags & NV_RX2_ERROR4) {
+ if ((flags & NV_RX2_ERROR_MASK) == NV_RX2_ERROR4) {
len = nv_getlen(dev, skb->data, len);
if (len < 0) {
dev_kfree_skb(skb);
}
}
/* framing errors are soft errors */
- else if (flags & NV_RX2_FRAMINGERR) {
+ else if ((flags & NV_RX2_ERROR_MASK) == NV_RX2_FRAMINGERR) {
if (flags & NV_RX2_SUBSTRACT1) {
len--;
}
u32 pause_enable = NVREG_TX_PAUSEFRAME_ENABLE_V1;
if (np->driver_data & DEV_HAS_PAUSEFRAME_TX_V2)
pause_enable = NVREG_TX_PAUSEFRAME_ENABLE_V2;
- if (np->driver_data & DEV_HAS_PAUSEFRAME_TX_V3)
+ if (np->driver_data & DEV_HAS_PAUSEFRAME_TX_V3) {
pause_enable = NVREG_TX_PAUSEFRAME_ENABLE_V3;
+ /* limit the number of tx pause frames to a default of 8 */
+ writel(readl(base + NvRegTxPauseFrameLimit)|NVREG_TX_PAUSEFRAMELIMIT_ENABLE, base + NvRegTxPauseFrameLimit);
+ }
writel(pause_enable, base + NvRegTxPauseFrame);
writel(regmisc|NVREG_MISC1_PAUSE_TX, base + NvRegMisc1);
np->pause_flags |= NV_PAUSEFRAME_TX_ENABLE;
return NV_DEV_STATISTICS_V1_COUNT;
else if (np->driver_data & DEV_HAS_STATISTICS_V2)
return NV_DEV_STATISTICS_V2_COUNT;
+ else if (np->driver_data & DEV_HAS_STATISTICS_V3)
+ return NV_DEV_STATISTICS_V3_COUNT;
else
return 0;
default:
mod_timer(&np->oom_kick, jiffies + OOM_REFILL);
/* start statistics timer */
- if (np->driver_data & (DEV_HAS_STATISTICS_V1|DEV_HAS_STATISTICS_V2))
+ if (np->driver_data & (DEV_HAS_STATISTICS_V1|DEV_HAS_STATISTICS_V2|DEV_HAS_STATISTICS_V3))
mod_timer(&np->stats_poll,
round_jiffies(jiffies + STATS_INTERVAL));
if (err < 0)
goto out_disable;
- if (id->driver_data & (DEV_HAS_VLAN|DEV_HAS_MSI_X|DEV_HAS_POWER_CNTRL|DEV_HAS_STATISTICS_V2))
+ if (id->driver_data & (DEV_HAS_VLAN|DEV_HAS_MSI_X|DEV_HAS_POWER_CNTRL|DEV_HAS_STATISTICS_V2|DEV_HAS_STATISTICS_V3))
np->register_size = NV_PCI_REGSZ_VER3;
else if (id->driver_data & DEV_HAS_STATISTICS_V1)
np->register_size = NV_PCI_REGSZ_VER2;
},
{ /* MCP77 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_32),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP77 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_33),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP77 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_34),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP77 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_35),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V2|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP79 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_36),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP79 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_37),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP79 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_38),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{ /* MCP79 Ethernet Controller */
PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_39),
- .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
+ .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_LARGEDESC|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX_V3|DEV_HAS_STATISTICS_V3|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT|DEV_HAS_CORRECT_MACADDR|DEV_HAS_COLLISION_FIX|DEV_NEED_TX_LIMIT|DEV_HAS_GEAR_MODE,
},
{0,},
};
#define FCC_NAPI_RX_EVENT_MSK (FCC_ENET_RXF | FCC_ENET_RXB)
#define FCC_RX_EVENT (FCC_ENET_RXF)
#define FCC_TX_EVENT (FCC_ENET_TXB)
-#define FCC_ERR_EVENT_MSK (FCC_ENET_TXE | FCC_ENET_BSY)
+#define FCC_ERR_EVENT_MSK (FCC_ENET_TXE)
static int setup_data(struct net_device *dev)
{
spin_unlock(&priv->rxlock);
spin_unlock_irqrestore(&priv->txlock, flags);
-#ifdef CONFIG_GFAR_NAPI
napi_disable(&priv->napi);
-#endif
if (magic_packet) {
/* Enable interrupt on Magic Packet */
netif_device_attach(dev);
-#ifdef CONFIG_GFAR_NAPI
napi_enable(&priv->napi);
-#endif
return 0;
}
}
printk(KERN_ERR "mkiss: %s: transmit timed out, %s?\n", dev->name,
- (ax->tty->ops->chars_in_buffer(ax->tty) || ax->xleft) ?
+ (tty_chars_in_buffer(ax->tty) || ax->xleft) ?
"bad line quality" : "driver error");
ax->xleft = 0;
struct net_device *_dev = (struct net_device *)dev;
struct ifb_private *dp = netdev_priv(_dev);
struct net_device_stats *stats = &_dev->stats;
+ struct netdev_queue *txq;
struct sk_buff *skb;
+ txq = netdev_get_tx_queue(_dev, 0);
dp->st_task_enter++;
if ((skb = skb_peek(&dp->tq)) == NULL) {
dp->st_txq_refl_try++;
- if (netif_tx_trylock(_dev)) {
+ if (__netif_tx_trylock(txq)) {
dp->st_rxq_enter++;
while ((skb = skb_dequeue(&dp->rq)) != NULL) {
skb_queue_tail(&dp->tq, skb);
dp->st_rx2tx_tran++;
}
- netif_tx_unlock(_dev);
+ __netif_tx_unlock(txq);
} else {
/* reschedule */
dp->st_rxq_notenter++;
BUG();
}
- if (netif_tx_trylock(_dev)) {
+ if (__netif_tx_trylock(txq)) {
dp->st_rxq_check++;
if ((skb = skb_peek(&dp->rq)) == NULL) {
dp->tasklet_pending = 0;
netif_wake_queue(_dev);
} else {
dp->st_rxq_rsch++;
- netif_tx_unlock(_dev);
+ __netif_tx_unlock(txq);
goto resched;
}
- netif_tx_unlock(_dev);
+ __netif_tx_unlock(txq);
} else {
resched:
dp->tasklet_pending = 1;
for (; mc_addr_count > 0; mc_addr_count--) {
hash_value = igb_hash_mc_addr(hw, mc_addr_list);
hw_dbg("Hash value = 0x%03X\n", hash_value);
- hw->mac.ops.mta_set(hw, hash_value);
+ igb_mta_set(hw, hash_value);
mc_addr_list += ETH_ALEN;
}
}
E1000_PCS_LCTL_FORCE_LINK; /* Force Link */
hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
}
+
+ if (hw->mac.type == e1000_82576) {
+ reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+ igb_force_mac_fc(hw);
+ }
+
wr32(E1000_PCS_LCTL, reg);
return 0;
return ret_val;
}
-/**
- * igb_translate_register_82576 - Translate the proper register offset
- * @reg: e1000 register to be read
- *
- * Registers in 82576 are located in different offsets than other adapters
- * even though they function in the same manner. This function takes in
- * the name of the register to read and returns the correct offset for
- * 82576 silicon.
- **/
-u32 igb_translate_register_82576(u32 reg)
-{
- /*
- * Some of the Kawela registers are located at different
- * offsets than they are in older adapters.
- * Despite the difference in location, the registers
- * function in the same manner.
- */
- switch (reg) {
- case E1000_TDBAL(0):
- reg = 0x0E000;
- break;
- case E1000_TDBAH(0):
- reg = 0x0E004;
- break;
- case E1000_TDLEN(0):
- reg = 0x0E008;
- break;
- case E1000_TDH(0):
- reg = 0x0E010;
- break;
- case E1000_TDT(0):
- reg = 0x0E018;
- break;
- case E1000_TXDCTL(0):
- reg = 0x0E028;
- break;
- case E1000_RDBAL(0):
- reg = 0x0C000;
- break;
- case E1000_RDBAH(0):
- reg = 0x0C004;
- break;
- case E1000_RDLEN(0):
- reg = 0x0C008;
- break;
- case E1000_RDH(0):
- reg = 0x0C010;
- break;
- case E1000_RDT(0):
- reg = 0x0C018;
- break;
- case E1000_RXDCTL(0):
- reg = 0x0C028;
- break;
- case E1000_SRRCTL(0):
- reg = 0x0C00C;
- break;
- default:
- break;
- }
-
- return reg;
-}
-
/**
* igb_reset_init_script_82575 - Inits HW defaults after reset
* @hw: pointer to the HW structure
#ifndef _E1000_82575_H_
#define _E1000_82575_H_
-u32 igb_translate_register_82576(u32 reg);
void igb_update_mc_addr_list_82575(struct e1000_hw*, u8*, u32, u32, u32);
extern void igb_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw);
extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw);
#define E1000_PCS_LCTL_FDV_FULL 8
#define E1000_PCS_LCTL_FSD 0x10
#define E1000_PCS_LCTL_FORCE_LINK 0x20
+#define E1000_PCS_LCTL_FORCE_FCTRL 0x80
#define E1000_PCS_LCTL_AN_ENABLE 0x10000
#define E1000_PCS_LCTL_AN_RESTART 0x20000
#define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
void (*rar_set)(struct e1000_hw *, u8 *, u32);
s32 (*read_mac_addr)(struct e1000_hw *);
s32 (*get_speed_and_duplex)(struct e1000_hw *, u16 *, u16 *);
- void (*mta_set)(struct e1000_hw *, u32);
};
struct e1000_phy_operations {
wrfl();
}
-/**
- * igb_init_rx_addrs - Initialize receive address's
- * @hw: pointer to the HW structure
- * @rar_count: receive address registers
- *
- * Setups the receive address registers by setting the base receive address
- * register to the devices MAC address and clearing all the other receive
- * address registers to 0.
- **/
-void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
-{
- u32 i;
-
- /* Setup the receive address */
- hw_dbg("Programming MAC Address into RAR[0]\n");
-
- hw->mac.ops.rar_set(hw, hw->mac.addr, 0);
-
- /* Zero out the other (rar_entry_count - 1) receive addresses */
- hw_dbg("Clearing RAR[1-%u]\n", rar_count-1);
- for (i = 1; i < rar_count; i++) {
- array_wr32(E1000_RA, (i << 1), 0);
- wrfl();
- array_wr32(E1000_RA, ((i << 1) + 1), 0);
- wrfl();
- }
-}
-
/**
* igb_check_alt_mac_addr - Check for alternate MAC addr
* @hw: pointer to the HW structure
* current value is read, the new bit is OR'd in and the new value is
* written back into the register.
**/
-static void igb_mta_set(struct e1000_hw *hw, u32 hash_value)
+void igb_mta_set(struct e1000_hw *hw, u32 hash_value)
{
u32 hash_bit, hash_reg, mta;
wrfl();
}
-/**
- * igb_update_mc_addr_list - Update Multicast addresses
- * @hw: pointer to the HW structure
- * @mc_addr_list: array of multicast addresses to program
- * @mc_addr_count: number of multicast addresses to program
- * @rar_used_count: the first RAR register free to program
- * @rar_count: total number of supported Receive Address Registers
- *
- * Updates the Receive Address Registers and Multicast Table Array.
- * The caller must have a packed mc_addr_list of multicast addresses.
- * The parameter rar_count will usually be hw->mac.rar_entry_count
- * unless there are workarounds that change this.
- **/
-void igb_update_mc_addr_list(struct e1000_hw *hw,
- u8 *mc_addr_list, u32 mc_addr_count,
- u32 rar_used_count, u32 rar_count)
-{
- u32 hash_value;
- u32 i;
-
- /*
- * Load the first set of multicast addresses into the exact
- * filters (RAR). If there are not enough to fill the RAR
- * array, clear the filters.
- */
- for (i = rar_used_count; i < rar_count; i++) {
- if (mc_addr_count) {
- hw->mac.ops.rar_set(hw, mc_addr_list, i);
- mc_addr_count--;
- mc_addr_list += ETH_ALEN;
- } else {
- array_wr32(E1000_RA, i << 1, 0);
- wrfl();
- array_wr32(E1000_RA, (i << 1) + 1, 0);
- wrfl();
- }
- }
-
- /* Clear the old settings from the MTA */
- hw_dbg("Clearing MTA\n");
- for (i = 0; i < hw->mac.mta_reg_count; i++) {
- array_wr32(E1000_MTA, i, 0);
- wrfl();
- }
-
- /* Load any remaining multicast addresses into the hash table. */
- for (; mc_addr_count > 0; mc_addr_count--) {
- hash_value = igb_hash_mc_addr(hw, mc_addr_list);
- hw_dbg("Hash value = 0x%03X\n", hash_value);
- igb_mta_set(hw, hash_value);
- mc_addr_list += ETH_ALEN;
- }
-}
-
/**
* igb_hash_mc_addr - Generate a multicast hash value
* @hw: pointer to the HW structure
u16 *duplex);
s32 igb_id_led_init(struct e1000_hw *hw);
s32 igb_led_off(struct e1000_hw *hw);
-void igb_update_mc_addr_list(struct e1000_hw *hw,
- u8 *mc_addr_list, u32 mc_addr_count,
- u32 rar_used_count, u32 rar_count);
s32 igb_setup_link(struct e1000_hw *hw);
s32 igb_validate_mdi_setting(struct e1000_hw *hw);
s32 igb_write_8bit_ctrl_reg(struct e1000_hw *hw, u32 reg,
void igb_clear_hw_cntrs_base(struct e1000_hw *hw);
void igb_clear_vfta(struct e1000_hw *hw);
void igb_config_collision_dist(struct e1000_hw *hw);
-void igb_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
+void igb_mta_set(struct e1000_hw *hw, u32 hash_value);
void igb_put_hw_semaphore(struct e1000_hw *hw);
void igb_rar_set(struct e1000_hw *hw, u8 *addr, u32 index);
s32 igb_check_alt_mac_addr(struct e1000_hw *hw);
#define E1000_RETA(_i) (0x05C00 + ((_i) * 4))
#define E1000_RSSRK(_i) (0x05C80 + ((_i) * 4)) /* RSS Random Key - RW Array */
-#define E1000_REGISTER(a, reg) (((a)->mac.type < e1000_82576) \
- ? reg : e1000_translate_register_82576(reg))
-
#define wr32(reg, value) (writel(value, hw->hw_addr + reg))
#define rd32(reg) (readl(hw->hw_addr + reg))
#define wrfl() ((void)rd32(E1000_STATUS))
array_wr32(E1000_MSIXBM(0), msix_vector, msixbm);
break;
case e1000_82576:
- /* Kawela uses a table-based method for assigning vectors.
+ /* The 82576 uses a table-based method for assigning vectors.
Each queue has a single entry in the table to which we write
a vector number along with a "valid" bit. Sadly, the layout
of the table is somewhat counterintuitive. */
ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
}
-static void igb_init_manageability(struct igb_adapter *adapter)
-{
- struct e1000_hw *hw = &adapter->hw;
-
- if (adapter->en_mng_pt) {
- u32 manc2h = rd32(E1000_MANC2H);
- u32 manc = rd32(E1000_MANC);
-
- /* enable receiving management packets to the host */
- /* this will probably generate destination unreachable messages
- * from the host OS, but the packets will be handled on SMBUS */
- manc |= E1000_MANC_EN_MNG2HOST;
-#define E1000_MNG2HOST_PORT_623 (1 << 5)
-#define E1000_MNG2HOST_PORT_664 (1 << 6)
- manc2h |= E1000_MNG2HOST_PORT_623;
- manc2h |= E1000_MNG2HOST_PORT_664;
- wr32(E1000_MANC2H, manc2h);
-
- wr32(E1000_MANC, manc);
- }
-}
-
/**
* igb_configure - configure the hardware for RX and TX
* @adapter: private board structure
igb_set_multi(netdev);
igb_restore_vlan(adapter);
- igb_init_manageability(adapter);
igb_configure_tx(adapter);
igb_setup_rctl(adapter);
unregister_netdev(netdev);
- if (!igb_check_reset_block(&adapter->hw))
+ if (adapter->hw.phy.ops.reset_phy &&
+ !igb_check_reset_block(&adapter->hw))
adapter->hw.phy.ops.reset_phy(&adapter->hw);
igb_remove_device(&adapter->hw);
struct net_device *netdev = pci_get_drvdata(pdev);
struct igb_adapter *adapter = netdev_priv(netdev);
- igb_init_manageability(adapter);
-
if (netif_running(netdev)) {
if (igb_up(adapter)) {
dev_err(&pdev->dev, "igb_up failed after reset\n");
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s()\n", __func__ );
/* Power on the dongle */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int act200l_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s()\n", __func__ );
/* Power off the dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
u8 control[3];
int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s()\n", __func__ );
/* Clear DTR and set RTS to enter command mode */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
};
int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s()\n", __func__ );
switch (state) {
case SIRDEV_STATE_DONGLE_RESET:
dev->speed = 9600;
break;
default:
- IRDA_ERROR("%s(), unknown state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s(), unknown state %d\n", __func__, state);
ret = -1;
break;
}
int ret = 0;
int i = 0;
- IRDA_DEBUG(4, "%s(), speed=%d (was %d)\n", __FUNCTION__,
+ IRDA_DEBUG(4, "%s(), speed=%d (was %d)\n", __func__,
speed, dev->speed);
/* dongle was already resetted from irda_request state machine,
int reg, revision;
int i = 0;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
ret = platform_driver_register(&ali_ircc_driver);
if (ret) {
/* Probe for all the ALi chipsets we know about */
for (chip= chips; chip->name; chip++, i++)
{
- IRDA_DEBUG(2, "%s(), Probing for %s ...\n", __FUNCTION__, chip->name);
+ IRDA_DEBUG(2, "%s(), Probing for %s ...\n", __func__, chip->name);
/* Try all config registers for this chip */
for (cfg=0; cfg<2; cfg++)
if (reg == chip->cid_value)
{
- IRDA_DEBUG(2, "%s(), Chip found at 0x%03x\n", __FUNCTION__, cfg_base);
+ IRDA_DEBUG(2, "%s(), Chip found at 0x%03x\n", __func__, cfg_base);
outb(0x1F, cfg_base);
revision = inb(cfg_base+1);
- IRDA_DEBUG(2, "%s(), Found %s chip, revision=%d\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), Found %s chip, revision=%d\n", __func__,
chip->name, revision);
/*
}
else
{
- IRDA_DEBUG(2, "%s(), No %s chip at 0x%03x\n", __FUNCTION__, chip->name, cfg_base);
+ IRDA_DEBUG(2, "%s(), No %s chip at 0x%03x\n", __func__, chip->name, cfg_base);
}
/* Exit configuration */
outb(0xbb, cfg_base);
}
}
- IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __func__);
if (ret)
platform_driver_unregister(&ali_ircc_driver);
{
int i;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
for (i=0; i < ARRAY_SIZE(dev_self); i++) {
if (dev_self[i])
platform_driver_unregister(&ali_ircc_driver);
- IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __func__);
}
/*
int dongle_id;
int err;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
if (i >= ARRAY_SIZE(dev_self)) {
IRDA_ERROR("%s(), maximum number of supported chips reached!\n",
- __FUNCTION__);
+ __func__);
return -ENOMEM;
}
dev = alloc_irdadev(sizeof(*self));
if (dev == NULL) {
IRDA_ERROR("%s(), can't allocate memory for control block!\n",
- __FUNCTION__);
+ __func__);
return -ENOMEM;
}
/* Reserve the ioports that we need */
if (!request_region(self->io.fir_base, self->io.fir_ext,
ALI_IRCC_DRIVER_NAME)) {
- IRDA_WARNING("%s(), can't get iobase of 0x%03x\n", __FUNCTION__,
+ IRDA_WARNING("%s(), can't get iobase of 0x%03x\n", __func__,
self->io.fir_base);
err = -ENODEV;
goto err_out1;
err = register_netdev(dev);
if (err) {
- IRDA_ERROR("%s(), register_netdev() failed!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), register_netdev() failed!\n", __func__);
goto err_out4;
}
IRDA_MESSAGE("IrDA: Registered device %s\n", dev->name);
/* Check dongle id */
dongle_id = ali_ircc_read_dongle_id(i, info);
- IRDA_MESSAGE("%s(), %s, Found dongle: %s\n", __FUNCTION__,
+ IRDA_MESSAGE("%s(), %s, Found dongle: %s\n", __func__,
ALI_IRCC_DRIVER_NAME, dongle_types[dongle_id]);
self->io.dongle_id = dongle_id;
- IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __func__);
return 0;
{
int iobase;
- IRDA_DEBUG(4, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s(), ---------------- Start ----------------\n", __func__);
IRDA_ASSERT(self != NULL, return -1;);
unregister_netdev(self->netdev);
/* Release the PORT that this driver is using */
- IRDA_DEBUG(4, "%s(), Releasing Region %03x\n", __FUNCTION__, self->io.fir_base);
+ IRDA_DEBUG(4, "%s(), Releasing Region %03x\n", __func__, self->io.fir_base);
release_region(self->io.fir_base, self->io.fir_ext);
if (self->tx_buff.head)
dev_self[self->index] = NULL;
free_netdev(self->netdev);
- IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __func__);
return 0;
}
int cfg_base = info->cfg_base;
int hi, low, reg;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
/* Enter Configuration */
outb(chip->entr1, cfg_base);
info->sir_base = info->fir_base;
- IRDA_DEBUG(2, "%s(), probing fir_base=0x%03x\n", __FUNCTION__, info->fir_base);
+ IRDA_DEBUG(2, "%s(), probing fir_base=0x%03x\n", __func__, info->fir_base);
/* Read IRQ control register */
outb(0x70, cfg_base);
reg = inb(cfg_base+1);
info->irq = reg & 0x0f;
- IRDA_DEBUG(2, "%s(), probing irq=%d\n", __FUNCTION__, info->irq);
+ IRDA_DEBUG(2, "%s(), probing irq=%d\n", __func__, info->irq);
/* Read DMA channel */
outb(0x74, cfg_base);
info->dma = reg & 0x07;
if(info->dma == 0x04)
- IRDA_WARNING("%s(), No DMA channel assigned !\n", __FUNCTION__);
+ IRDA_WARNING("%s(), No DMA channel assigned !\n", __func__);
else
- IRDA_DEBUG(2, "%s(), probing dma=%d\n", __FUNCTION__, info->dma);
+ IRDA_DEBUG(2, "%s(), probing dma=%d\n", __func__, info->dma);
/* Read Enabled Status */
outb(0x30, cfg_base);
reg = inb(cfg_base+1);
info->enabled = (reg & 0x80) && (reg & 0x01);
- IRDA_DEBUG(2, "%s(), probing enabled=%d\n", __FUNCTION__, info->enabled);
+ IRDA_DEBUG(2, "%s(), probing enabled=%d\n", __func__, info->enabled);
/* Read Power Status */
outb(0x22, cfg_base);
reg = inb(cfg_base+1);
info->suspended = (reg & 0x20);
- IRDA_DEBUG(2, "%s(), probing suspended=%d\n", __FUNCTION__, info->suspended);
+ IRDA_DEBUG(2, "%s(), probing suspended=%d\n", __func__, info->suspended);
/* Exit configuration */
outb(0xbb, cfg_base);
- IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End -----------------\n", __func__);
return 0;
}
int version;
int iobase = info->fir_base;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
/* Locking comments :
* Most operations here need to be protected. We are called before
// outb(UART_IER_RDI, iobase+UART_IER); //benjamin 2000/11/23 01:25PM
// Turn on the interrupts in ali_ircc_net_open
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__);
return 0;
}
int dongle_id, reg;
int cfg_base = info->cfg_base;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
/* Enter Configuration */
outb(chips[i].entr1, cfg_base);
outb(0xf0, cfg_base);
reg = inb(cfg_base+1);
dongle_id = ((reg>>6)&0x02) | ((reg>>5)&0x01);
- IRDA_DEBUG(2, "%s(), probing dongle_id=%d, dongle_types=%s\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), probing dongle_id=%d, dongle_types=%s\n", __func__,
dongle_id, dongle_types[dongle_id]);
/* Exit configuration */
outb(0xbb, cfg_base);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__);
return dongle_id;
}
struct ali_ircc_cb *self;
int ret;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
self = dev->priv;
spin_unlock(&self->lock);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__);
return ret;
}
/*
__u8 eir, OldMessageCount;
int iobase, tmp;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__);
iobase = self->io.fir_base;
//self->ier = inb(iobase+FIR_IER); 2000/12/1 04:32PM
eir = self->InterruptID & self->ier; /* Mask out the interesting ones */
- IRDA_DEBUG(1, "%s(), self->InterruptID = %x\n", __FUNCTION__,self->InterruptID);
- IRDA_DEBUG(1, "%s(), self->LineStatus = %x\n", __FUNCTION__,self->LineStatus);
- IRDA_DEBUG(1, "%s(), self->ier = %x\n", __FUNCTION__,self->ier);
- IRDA_DEBUG(1, "%s(), eir = %x\n", __FUNCTION__,eir);
+ IRDA_DEBUG(1, "%s(), self->InterruptID = %x\n", __func__,self->InterruptID);
+ IRDA_DEBUG(1, "%s(), self->LineStatus = %x\n", __func__,self->LineStatus);
+ IRDA_DEBUG(1, "%s(), self->ier = %x\n", __func__,self->ier);
+ IRDA_DEBUG(1, "%s(), eir = %x\n", __func__,eir);
/* Disable interrupts */
SetCOMInterrupts(self, FALSE);
{
if (self->io.direction == IO_XMIT) /* TX */
{
- IRDA_DEBUG(1, "%s(), ******* IIR_EOM (Tx) *******\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* IIR_EOM (Tx) *******\n", __func__);
if(ali_ircc_dma_xmit_complete(self))
{
}
else /* RX */
{
- IRDA_DEBUG(1, "%s(), ******* IIR_EOM (Rx) *******\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* IIR_EOM (Rx) *******\n", __func__);
if(OldMessageCount > ((self->LineStatus+1) & 0x07))
{
self->rcvFramesOverflow = TRUE;
- IRDA_DEBUG(1, "%s(), ******* self->rcvFramesOverflow = TRUE ******** \n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* self->rcvFramesOverflow = TRUE ******** \n", __func__);
}
if (ali_ircc_dma_receive_complete(self))
{
- IRDA_DEBUG(1, "%s(), ******* receive complete ******** \n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* receive complete ******** \n", __func__);
self->ier = IER_EOM;
}
else
{
- IRDA_DEBUG(1, "%s(), ******* Not receive complete ******** \n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* Not receive complete ******** \n", __func__);
self->ier = IER_EOM | IER_TIMER;
}
if(OldMessageCount > ((self->LineStatus+1) & 0x07))
{
self->rcvFramesOverflow = TRUE;
- IRDA_DEBUG(1, "%s(), ******* self->rcvFramesOverflow = TRUE ******* \n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ******* self->rcvFramesOverflow = TRUE ******* \n", __func__);
}
/* Disable Timer */
switch_bank(iobase, BANK1);
/* Restore Interrupt */
SetCOMInterrupts(self, TRUE);
- IRDA_DEBUG(1, "%s(), ----------------- End ---------------\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), ----------------- End ---------------\n", __func__);
return IRQ_RETVAL(eir);
}
int iobase;
int iir, lsr;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
iobase = self->io.sir_base;
/* Clear interrupt */
lsr = inb(iobase+UART_LSR);
- IRDA_DEBUG(4, "%s(), iir=%02x, lsr=%02x, iobase=%#x\n", __FUNCTION__,
+ IRDA_DEBUG(4, "%s(), iir=%02x, lsr=%02x, iobase=%#x\n", __func__,
iir, lsr, iobase);
switch (iir)
{
case UART_IIR_RLSI:
- IRDA_DEBUG(2, "%s(), RLSI\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), RLSI\n", __func__);
break;
case UART_IIR_RDI:
/* Receive interrupt */
}
break;
default:
- IRDA_DEBUG(0, "%s(), unhandled IIR=%#x\n", __FUNCTION__, iir);
+ IRDA_DEBUG(0, "%s(), unhandled IIR=%#x\n", __func__, iir);
break;
}
}
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__);
return IRQ_RETVAL(iir);
}
int boguscount = 0;
int iobase;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__);
IRDA_ASSERT(self != NULL, return;);
iobase = self->io.sir_base;
/* Make sure we don't stay here too long */
if (boguscount++ > 32) {
- IRDA_DEBUG(2,"%s(), breaking!\n", __FUNCTION__);
+ IRDA_DEBUG(2,"%s(), breaking!\n", __func__);
break;
}
} while (inb(iobase+UART_LSR) & UART_LSR_DR);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
}
/*
IRDA_ASSERT(self != NULL, return;);
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
iobase = self->io.sir_base;
{
/* We must wait until all data are gone */
while(!(inb(iobase+UART_LSR) & UART_LSR_TEMT))
- IRDA_DEBUG(1, "%s(), UART_LSR_THRE\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), UART_LSR_THRE\n", __func__ );
- IRDA_DEBUG(1, "%s(), Changing speed! self->new_speed = %d\n", __FUNCTION__ , self->new_speed);
+ IRDA_DEBUG(1, "%s(), Changing speed! self->new_speed = %d\n", __func__ , self->new_speed);
ali_ircc_change_speed(self, self->new_speed);
self->new_speed = 0;
// benjamin 2000/11/10 06:32PM
if (self->io.speed > 115200)
{
- IRDA_DEBUG(2, "%s(), ali_ircc_change_speed from UART_LSR_TEMT \n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ali_ircc_change_speed from UART_LSR_TEMT \n", __func__ );
self->ier = IER_EOM;
// SetCOMInterrupts(self, TRUE);
outb(UART_IER_RDI, iobase+UART_IER);
}
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
}
static void ali_ircc_change_speed(struct ali_ircc_cb *self, __u32 baud)
struct net_device *dev = self->netdev;
int iobase;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
- IRDA_DEBUG(2, "%s(), setting speed = %d \n", __FUNCTION__ , baud);
+ IRDA_DEBUG(2, "%s(), setting speed = %d \n", __func__ , baud);
/* This function *must* be called with irq off and spin-lock.
* - Jean II */
netif_wake_queue(self->netdev);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
}
static void ali_ircc_fir_change_speed(struct ali_ircc_cb *priv, __u32 baud)
struct ali_ircc_cb *self = (struct ali_ircc_cb *) priv;
struct net_device *dev;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
IRDA_ASSERT(self != NULL, return;);
dev = self->netdev;
iobase = self->io.fir_base;
- IRDA_DEBUG(1, "%s(), self->io.speed = %d, change to speed = %d\n", __FUNCTION__ ,self->io.speed,baud);
+ IRDA_DEBUG(1, "%s(), self->io.speed = %d, change to speed = %d\n", __func__ ,self->io.speed,baud);
/* Come from SIR speed */
if(self->io.speed <=115200)
// Set Dongle Speed mode
ali_ircc_change_dongle_speed(self, baud);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
/*
int lcr; /* Line control reg */
int divisor;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
- IRDA_DEBUG(1, "%s(), Setting speed to: %d\n", __FUNCTION__ , speed);
+ IRDA_DEBUG(1, "%s(), Setting speed to: %d\n", __func__ , speed);
IRDA_ASSERT(self != NULL, return;);
spin_unlock_irqrestore(&self->lock, flags);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
static void ali_ircc_change_dongle_speed(struct ali_ircc_cb *priv, int speed)
int iobase,dongle_id;
int tmp = 0;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
iobase = self->io.fir_base; /* or iobase = self->io.sir_base; */
dongle_id = self->io.dongle_id;
/* We are already locked, no need to do it again */
- IRDA_DEBUG(1, "%s(), Set Speed for %s , Speed = %d\n", __FUNCTION__ , dongle_types[dongle_id], speed);
+ IRDA_DEBUG(1, "%s(), Set Speed for %s , Speed = %d\n", __func__ , dongle_types[dongle_id], speed);
switch_bank(iobase, BANK2);
tmp = inb(iobase+FIR_IRDA_CR);
switch_bank(iobase, BANK0);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
/*
{
int actual = 0;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
/* Tx FIFO should be empty! */
if (!(inb(iobase+UART_LSR) & UART_LSR_THRE)) {
- IRDA_DEBUG(0, "%s(), failed, fifo not empty!\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), failed, fifo not empty!\n", __func__ );
return 0;
}
actual++;
}
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return actual;
}
int iobase;
char hwname[32];
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
IRDA_ASSERT(dev != NULL, return -1;);
*/
self->irlap = irlap_open(dev, &self->qos, hwname);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return 0;
}
struct ali_ircc_cb *self;
//int iobase;
- IRDA_DEBUG(4, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s(), ---------------- Start ----------------\n", __func__ );
IRDA_ASSERT(dev != NULL, return -1;);
free_irq(self->io.irq, dev);
free_dma(self->io.dma);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return 0;
}
__u32 speed;
int mtt, diff;
- IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __func__ );
self = (struct ali_ircc_cb *) dev->priv;
iobase = self->io.fir_base;
diff = self->now.tv_usec - self->stamp.tv_usec;
/* self->stamp is set from ali_ircc_dma_receive_complete() */
- IRDA_DEBUG(1, "%s(), ******* diff = %d ******* \n", __FUNCTION__ , diff);
+ IRDA_DEBUG(1, "%s(), ******* diff = %d ******* \n", __func__ , diff);
if (diff < 0)
diff += 1000000;
/* Adjust for timer resolution */
mtt = (mtt+250) / 500; /* 4 discard, 5 get advanced, Let's round off */
- IRDA_DEBUG(1, "%s(), ************** mtt = %d ***********\n", __FUNCTION__ , mtt);
+ IRDA_DEBUG(1, "%s(), ************** mtt = %d ***********\n", __func__ , mtt);
/* Setup timer */
if (mtt == 1) /* 500 us */
spin_unlock_irqrestore(&self->lock, flags);
dev_kfree_skb(skb);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
return 0;
}
unsigned char FIFO_OPTI, Hi, Lo;
- IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __func__ );
iobase = self->io.fir_base;
tmp = inb(iobase+FIR_LCR_B);
tmp &= ~0x20; // Disable SIP
outb(((unsigned char)(tmp & 0x3f) | LCR_B_TX_MODE) & ~LCR_B_BW, iobase+FIR_LCR_B);
- IRDA_DEBUG(1, "%s(), ******* Change to TX mode: FIR_LCR_B = 0x%x ******* \n", __FUNCTION__ , inb(iobase+FIR_LCR_B));
+ IRDA_DEBUG(1, "%s(), ******* Change to TX mode: FIR_LCR_B = 0x%x ******* \n", __func__ , inb(iobase+FIR_LCR_B));
outb(0, iobase+FIR_LSR);
switch_bank(iobase, BANK0);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
static int ali_ircc_dma_xmit_complete(struct ali_ircc_cb *self)
int iobase;
int ret = TRUE;
- IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __func__ );
iobase = self->io.fir_base;
if((inb(iobase+FIR_LSR) & LSR_FRAME_ABORT) == LSR_FRAME_ABORT)
{
- IRDA_ERROR("%s(), ********* LSR_FRAME_ABORT *********\n", __FUNCTION__);
+ IRDA_ERROR("%s(), ********* LSR_FRAME_ABORT *********\n", __func__);
self->stats.tx_errors++;
self->stats.tx_fifo_errors++;
}
switch_bank(iobase, BANK0);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
return ret;
}
{
int iobase, tmp;
- IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __func__ );
iobase = self->io.fir_base;
//switch_bank(iobase, BANK0);
tmp = inb(iobase+FIR_LCR_B);
outb((unsigned char)(tmp &0x3f) | LCR_B_RX_MODE | LCR_B_BW , iobase + FIR_LCR_B); // 2000/12/1 05:16PM
- IRDA_DEBUG(1, "%s(), *** Change To RX mode: FIR_LCR_B = 0x%x *** \n", __FUNCTION__ , inb(iobase+FIR_LCR_B));
+ IRDA_DEBUG(1, "%s(), *** Change To RX mode: FIR_LCR_B = 0x%x *** \n", __func__ , inb(iobase+FIR_LCR_B));
/* Set Rx Threshold */
switch_bank(iobase, BANK1);
outb(CR_DMA_EN | CR_DMA_BURST, iobase+FIR_CR);
switch_bank(iobase, BANK0);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
return 0;
}
__u8 status, MessageCount;
int len, i, iobase, val;
- IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start -----------------\n", __func__ );
st_fifo = &self->st_fifo;
iobase = self->io.fir_base;
MessageCount = inb(iobase+ FIR_LSR)&0x07;
if (MessageCount > 0)
- IRDA_DEBUG(0, "%s(), Messsage count = %d,\n", __FUNCTION__ , MessageCount);
+ IRDA_DEBUG(0, "%s(), Messsage count = %d,\n", __func__ , MessageCount);
for (i=0; i<=MessageCount; i++)
{
len = len << 8;
len |= inb(iobase+FIR_RX_DSR_LO);
- IRDA_DEBUG(1, "%s(), RX Length = 0x%.2x,\n", __FUNCTION__ , len);
- IRDA_DEBUG(1, "%s(), RX Status = 0x%.2x,\n", __FUNCTION__ , status);
+ IRDA_DEBUG(1, "%s(), RX Length = 0x%.2x,\n", __func__ , len);
+ IRDA_DEBUG(1, "%s(), RX Status = 0x%.2x,\n", __func__ , status);
if (st_fifo->tail >= MAX_RX_WINDOW) {
- IRDA_DEBUG(0, "%s(), window is full!\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), window is full!\n", __func__ );
continue;
}
/* Check for errors */
if ((status & 0xd8) || self->rcvFramesOverflow || (len==0))
{
- IRDA_DEBUG(0,"%s(), ************* RX Errors ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ************* RX Errors ************ \n", __func__ );
/* Skip frame */
self->stats.rx_errors++;
if (status & LSR_FIFO_UR)
{
self->stats.rx_frame_errors++;
- IRDA_DEBUG(0,"%s(), ************* FIFO Errors ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ************* FIFO Errors ************ \n", __func__ );
}
if (status & LSR_FRAME_ERROR)
{
self->stats.rx_frame_errors++;
- IRDA_DEBUG(0,"%s(), ************* FRAME Errors ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ************* FRAME Errors ************ \n", __func__ );
}
if (status & LSR_CRC_ERROR)
{
self->stats.rx_crc_errors++;
- IRDA_DEBUG(0,"%s(), ************* CRC Errors ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ************* CRC Errors ************ \n", __func__ );
}
if(self->rcvFramesOverflow)
{
self->stats.rx_frame_errors++;
- IRDA_DEBUG(0,"%s(), ************* Overran DMA buffer ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ************* Overran DMA buffer ************ \n", __func__ );
}
if(len == 0)
{
self->stats.rx_frame_errors++;
- IRDA_DEBUG(0,"%s(), ********** Receive Frame Size = 0 ********* \n", __FUNCTION__ );
+ IRDA_DEBUG(0,"%s(), ********** Receive Frame Size = 0 ********* \n", __func__ );
}
}
else
val = inb(iobase+FIR_BSR);
if ((val& BSR_FIFO_NOT_EMPTY)== 0x80)
{
- IRDA_DEBUG(0, "%s(), ************* BSR_FIFO_NOT_EMPTY ************ \n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), ************* BSR_FIFO_NOT_EMPTY ************ \n", __func__ );
/* Put this entry back in fifo */
st_fifo->head--;
{
IRDA_WARNING("%s(), memory squeeze, "
"dropping frame.\n",
- __FUNCTION__);
+ __func__);
self->stats.rx_dropped++;
return FALSE;
switch_bank(iobase, BANK0);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
return TRUE;
}
int iobase;
__u32 speed;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
IRDA_ASSERT(dev != NULL, return 0;);
dev_kfree_skb(skb);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return 0;
}
unsigned long flags;
int ret = 0;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
IRDA_ASSERT(dev != NULL, return -1;);
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__ , dev->name, cmd);
+ IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__ , dev->name, cmd);
switch (cmd) {
case SIOCSBANDWIDTH: /* Set bandwidth */
- IRDA_DEBUG(1, "%s(), SIOCSBANDWIDTH\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), SIOCSBANDWIDTH\n", __func__ );
/*
* This function will also be used by IrLAP to change the
* speed, so we still must allow for speed change within
spin_unlock_irqrestore(&self->lock, flags);
break;
case SIOCSMEDIABUSY: /* Set media busy */
- IRDA_DEBUG(1, "%s(), SIOCSMEDIABUSY\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), SIOCSMEDIABUSY\n", __func__ );
if (!capable(CAP_NET_ADMIN))
return -EPERM;
irda_device_set_media_busy(self->netdev, TRUE);
break;
case SIOCGRECEIVING: /* Check if we are receiving right now */
- IRDA_DEBUG(2, "%s(), SIOCGRECEIVING\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), SIOCGRECEIVING\n", __func__ );
/* This is protected */
irq->ifr_receiving = ali_ircc_is_receiving(self);
break;
ret = -EOPNOTSUPP;
}
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return ret;
}
int status = FALSE;
int iobase;
- IRDA_DEBUG(2, "%s(), ---------------- Start -----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start -----------------\n", __func__ );
IRDA_ASSERT(self != NULL, return FALSE;);
if((inb(iobase+FIR_FIFO_FR) & 0x3f) != 0)
{
/* We are receiving something */
- IRDA_DEBUG(1, "%s(), We are receiving something\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), We are receiving something\n", __func__ );
status = TRUE;
}
switch_bank(iobase, BANK0);
spin_unlock_irqrestore(&self->lock, flags);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return status;
}
{
struct ali_ircc_cb *self = (struct ali_ircc_cb *) dev->priv;
- IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ---------------- Start ----------------\n", __func__ );
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
return &self->stats;
}
int iobase = self->io.fir_base; /* or sir_base */
- IRDA_DEBUG(2, "%s(), -------- Start -------- ( Enable = %d )\n", __FUNCTION__ , enable);
+ IRDA_DEBUG(2, "%s(), -------- Start -------- ( Enable = %d )\n", __func__ , enable);
/* Enable the interrupt which we wish to */
if (enable){
else
outb(newMask, iobase+UART_IER);
- IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(2, "%s(), ----------------- End ------------------\n", __func__ );
}
static void SIR2FIR(int iobase)
{
//unsigned char tmp;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
/* Already protected (change_speed() or setup()), no need to lock.
* Jean II */
//tmp |= 0x20;
//outb(tmp, iobase+FIR_LCR_B);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
static void FIR2SIR(int iobase)
{
unsigned char val;
- IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ---------------- Start ----------------\n", __func__ );
/* Already protected (change_speed() or setup()), no need to lock.
* Jean II */
val = inb(iobase+UART_LSR);
val = inb(iobase+UART_MSR);
- IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __FUNCTION__ );
+ IRDA_DEBUG(1, "%s(), ----------------- End ------------------\n", __func__ );
}
MODULE_AUTHOR("Benjamin Kong <benjamin_kong@ali.com.tw>");
{
__u32 ringbase;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
ringbase = INB (OBOE_RING_BASE0) << 10;
ringbase |= INB (OBOE_RING_BASE1) << 18;
toshoboe_disablebm (struct toshoboe_cb *self)
{
__u8 command;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
pci_read_config_byte (self->pdev, PCI_COMMAND, &command);
command &= ~PCI_COMMAND_MASTER;
static void
toshoboe_stopchip (struct toshoboe_cb *self)
{
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
/*Disable interrupts */
OUTB (0x0, OBOE_IER);
__u16 pconfig = 0;
__u8 config0l = 0;
- IRDA_DEBUG (2, "%s(%d/%d)\n", __FUNCTION__, self->speed, self->io.speed);
+ IRDA_DEBUG (2, "%s(%d/%d)\n", __func__, self->speed, self->io.speed);
switch (self->speed)
{
static void
toshoboe_enablebm (struct toshoboe_cb *self)
{
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
pci_set_master (self->pdev);
}
{
int i;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
for (i = 0; i < TX_SLOTS; ++i)
{
{
__u32 physaddr;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
toshoboe_initring (self);
toshoboe_enablebm (self);
#endif
unsigned long flags;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
if (request_irq (self->io.irq, toshoboe_probeinterrupt,
self->io.irqflags, "toshoboe", (void *) self))
IRDA_ASSERT (self != NULL, return 0; );
- IRDA_DEBUG (1, "%s.tx:%x(%x)%x\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s.tx:%x(%x)%x\n", __func__
,skb->len,self->txpending,INB (OBOE_ENABLEH));
if (!cb->magic) {
- IRDA_DEBUG (2, "%s.Not IrLAP:%x\n", __FUNCTION__, cb->magic);
+ IRDA_DEBUG (2, "%s.Not IrLAP:%x\n", __func__, cb->magic);
#ifdef DUMP_PACKETS
_dumpbufs(skb->data,skb->len,'>');
#endif
{
self->new_speed = speed;
IRDA_DEBUG (1, "%s: Queued TxDone scheduled speed change %d\n" ,
- __FUNCTION__, speed);
+ __func__, speed);
/* if no data, that's all! */
if (!skb->len)
{
/* which we will add a wrong checksum to */
mtt = toshoboe_makemttpacket (self, self->tx_bufs[self->txs], mtt);
- IRDA_DEBUG (1, "%s.mtt:%x(%x)%d\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s.mtt:%x(%x)%d\n", __func__
,skb->len,mtt,self->txpending);
if (mtt)
{
if (self->ring->tx[self->txs].control & OBOE_CTL_TX_HW_OWNS)
{
- IRDA_DEBUG (0, "%s.ful:%x(%x)%x\n", __FUNCTION__
+ IRDA_DEBUG (0, "%s.ful:%x(%x)%x\n", __func__
,skb->len, self->ring->tx[self->txs].control, self->txpending);
toshoboe_start_DMA(self, OBOE_CONFIG0H_ENTX);
spin_unlock_irqrestore(&self->spinlock, flags);
if (self->ring->tx[i].control & OBOE_CTL_TX_HW_OWNS)
self->txpending++;
}
- IRDA_DEBUG (1, "%s.txd(%x)%x/%x\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s.txd(%x)%x/%x\n", __func__
,irqstat,txp,self->txpending);
txp = INB (OBOE_TXSLOT) & OBOE_SLOT_MASK;
{
self->speed = self->new_speed;
IRDA_DEBUG (1, "%s: Executed TxDone scheduled speed change %d\n",
- __FUNCTION__, self->speed);
+ __func__, self->speed);
toshoboe_setbaud (self);
}
{
int len = self->ring->rx[self->rxs].len;
skb = NULL;
- IRDA_DEBUG (3, "%s.rcv:%x(%x)\n", __FUNCTION__
+ IRDA_DEBUG (3, "%s.rcv:%x(%x)\n", __func__
,len,self->ring->rx[self->rxs].control);
#ifdef DUMP_PACKETS
len -= 2;
else
len = 0;
- IRDA_DEBUG (1, "%s.SIR:%x(%x)\n", __FUNCTION__, len,enable);
+ IRDA_DEBUG (1, "%s.SIR:%x(%x)\n", __func__, len,enable);
}
#ifdef USE_MIR
len -= 2;
else
len = 0;
- IRDA_DEBUG (2, "%s.MIR:%x(%x)\n", __FUNCTION__, len,enable);
+ IRDA_DEBUG (2, "%s.MIR:%x(%x)\n", __func__, len,enable);
}
#endif
else if (enable & OBOE_ENABLEH_FIRON)
len -= 4; /*FIXME: check this */
else
len = 0;
- IRDA_DEBUG (1, "%s.FIR:%x(%x)\n", __FUNCTION__, len,enable);
+ IRDA_DEBUG (1, "%s.FIR:%x(%x)\n", __func__, len,enable);
}
else
- IRDA_DEBUG (0, "%s.?IR:%x(%x)\n", __FUNCTION__, len,enable);
+ IRDA_DEBUG (0, "%s.?IR:%x(%x)\n", __func__, len,enable);
if (len)
{
{
printk (KERN_INFO
"%s(), memory squeeze, dropping frame.\n",
- __FUNCTION__);
+ __func__);
}
}
}
/* (SIR) data is splitted in several slots. */
/* we have to join all the received buffers received */
/*in a large buffer before checking CRC. */
- IRDA_DEBUG (0, "%s.err:%x(%x)\n", __FUNCTION__
+ IRDA_DEBUG (0, "%s.err:%x(%x)\n", __func__
,len,self->ring->rx[self->rxs].control);
}
if (irqstat & OBOE_INT_SIP)
{
self->int_sip++;
- IRDA_DEBUG (1, "%s.sip:%x(%x)%x\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s.sip:%x(%x)%x\n", __func__
,self->int_sip,irqstat,self->txpending);
}
return IRQ_HANDLED;
unsigned long flags;
int rc;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
self = netdev_priv(dev);
{
struct toshoboe_cb *self;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
IRDA_ASSERT (dev != NULL, return -1; );
self = (struct toshoboe_cb *) dev->priv;
IRDA_ASSERT (self != NULL, return -1; );
- IRDA_DEBUG (5, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd);
+ IRDA_DEBUG (5, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
/* Disable interrupts & save flags */
spin_lock_irqsave(&self->spinlock, flags);
* speed, so we still must allow for speed change within
* interrupt context.
*/
- IRDA_DEBUG (1, "%s(BANDWIDTH), %s, (%X/%ld\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s(BANDWIDTH), %s, (%X/%ld\n", __func__
,dev->name, INB (OBOE_STATUS), irq->ifr_baudrate );
if (!in_interrupt () && !capable (CAP_NET_ADMIN)) {
ret = -EPERM;
self->new_speed = irq->ifr_baudrate;
break;
case SIOCSMEDIABUSY: /* Set media busy */
- IRDA_DEBUG (1, "%s(MEDIABUSY), %s, (%X/%x)\n", __FUNCTION__
+ IRDA_DEBUG (1, "%s(MEDIABUSY), %s, (%X/%x)\n", __func__
,dev->name, INB (OBOE_STATUS), capable (CAP_NET_ADMIN) );
if (!capable (CAP_NET_ADMIN)) {
ret = -EPERM;
break;
case SIOCGRECEIVING: /* Check if we are receiving right now */
irq->ifr_receiving = (INB (OBOE_STATUS) & OBOE_STATUS_RXBUSY) ? 1 : 0;
- IRDA_DEBUG (3, "%s(RECEIVING), %s, (%X/%x)\n", __FUNCTION__
+ IRDA_DEBUG (3, "%s(RECEIVING), %s, (%X/%x)\n", __func__
,dev->name, INB (OBOE_STATUS), irq->ifr_receiving );
break;
default:
- IRDA_DEBUG (1, "%s(?), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd);
+ IRDA_DEBUG (1, "%s(?), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
ret = -EOPNOTSUPP;
}
out:
int i;
struct toshoboe_cb *self = (struct toshoboe_cb*)pci_get_drvdata(pci_dev);
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
IRDA_ASSERT (self != NULL, return; );
int ok = 0;
int err;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
if ((err=pci_enable_device(pci_dev)))
return err;
unsigned long flags;
int i = 10;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
if (!self || self->stopped)
return 0;
struct toshoboe_cb *self = (struct toshoboe_cb*)pci_get_drvdata(pci_dev);
unsigned long flags;
- IRDA_DEBUG (4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG (4, "%s()\n", __func__);
if (!self || !self->stopped)
return 0;
#include <net/irda/irda_device.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include "sir-dev.h"
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power on dongle */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int girbil_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
u8 control[2];
static int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* dongle alread reset - port and dongle at default speed */
break;
default:
- IRDA_ERROR("%s - undefined state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s - undefined state %d\n", __func__, state);
ret = -EINVAL;
break;
}
u8 control = GIRBIL_TXEN | GIRBIL_RXEN;
int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
switch (state) {
case SIRDEV_STATE_DONGLE_RESET:
break;
default:
- IRDA_ERROR("%s(), undefined state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s(), undefined state %d\n", __func__, state);
ret = -1;
break;
}
(!force) && (self->speed != -1)) {
/* No speed and xbofs change here
* (we'll do it later in the write callback) */
- IRDA_DEBUG(2, "%s(), not changing speed yet\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), not changing speed yet\n", __func__);
*header = 0;
return;
}
- IRDA_DEBUG(2, "%s(), changing speed to %d\n", __FUNCTION__, self->new_speed);
+ IRDA_DEBUG(2, "%s(), changing speed to %d\n", __func__, self->new_speed);
self->speed = self->new_speed;
/* We will do ` self->new_speed = -1; ' in the completion
* handler just in case the current URB fail - Jean II */
/* Set the negotiated additional XBOFS */
if (self->new_xbofs != -1) {
- IRDA_DEBUG(2, "%s(), changing xbofs to %d\n", __FUNCTION__, self->new_xbofs);
+ IRDA_DEBUG(2, "%s(), changing xbofs to %d\n", __func__, self->new_xbofs);
self->xbofs = self->new_xbofs;
/* We will do ` self->new_xbofs = -1; ' in the completion
* handler just in case the current URB fail - Jean II */
struct urb *urb;
int ret;
- IRDA_DEBUG(2, "%s(), speed=%d, xbofs=%d\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), speed=%d, xbofs=%d\n", __func__,
self->new_speed, self->new_xbofs);
/* Grab the speed URB */
urb = self->speed_urb;
if (urb->status != 0) {
- IRDA_WARNING("%s(), URB still in use!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), URB still in use!\n", __func__);
return;
}
/* Irq disabled -> GFP_ATOMIC */
if ((ret = usb_submit_urb(urb, GFP_ATOMIC))) {
- IRDA_WARNING("%s(), failed Speed URB\n", __FUNCTION__);
+ IRDA_WARNING("%s(), failed Speed URB\n", __func__);
}
}
{
struct irda_usb_cb *self = urb->context;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* We should always have a context */
IRDA_ASSERT(self != NULL, return;);
/* Check for timeout and other USB nasties */
if (urb->status != 0) {
/* I get a lot of -ECONNABORTED = -103 here - Jean II */
- IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __FUNCTION__, urb->status, urb->transfer_flags);
+ IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
/* Don't do anything here, that might confuse the USB layer.
* Instead, we will wait for irda_usb_net_timeout(), the
int res, mtt;
int err = 1; /* Failed */
- IRDA_DEBUG(4, "%s() on %s\n", __FUNCTION__, netdev->name);
+ IRDA_DEBUG(4, "%s() on %s\n", __func__, netdev->name);
netif_stop_queue(netdev);
* We need to check self->present under the spinlock because
* of irda_usb_disconnect() is synchronous - Jean II */
if (!self->present) {
- IRDA_DEBUG(0, "%s(), Device is gone...\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), Device is gone...\n", __func__);
goto drop;
}
}
if (urb->status != 0) {
- IRDA_WARNING("%s(), URB still in use!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), URB still in use!\n", __func__);
goto drop;
}
/* Ask USB to send the packet - Irq disabled -> GFP_ATOMIC */
if ((res = usb_submit_urb(urb, GFP_ATOMIC))) {
- IRDA_WARNING("%s(), failed Tx URB\n", __FUNCTION__);
+ IRDA_WARNING("%s(), failed Tx URB\n", __func__);
self->stats.tx_errors++;
/* Let USB recover : We will catch that in the watchdog */
/*netif_start_queue(netdev);*/
struct sk_buff *skb = urb->context;
struct irda_usb_cb *self = ((struct irda_skb_cb *) skb->cb)->context;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* We should always have a context */
IRDA_ASSERT(self != NULL, return;);
/* Check for timeout and other USB nasties */
if (urb->status != 0) {
/* I get a lot of -ECONNABORTED = -103 here - Jean II */
- IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __FUNCTION__, urb->status, urb->transfer_flags);
+ IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
/* Don't do anything here, that might confuse the USB layer,
* and we could go in recursion and blow the kernel stack...
/* If the network is closed, stop everything */
if ((!self->netopen) || (!self->present)) {
- IRDA_DEBUG(0, "%s(), Network is gone...\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), Network is gone...\n", __func__);
spin_unlock_irqrestore(&self->lock, flags);
return;
}
(self->new_xbofs != self->xbofs)) {
/* We haven't changed speed yet (because of
* IUC_SPEED_BUG), so do it now - Jean II */
- IRDA_DEBUG(1, "%s(), Changing speed now...\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), Changing speed now...\n", __func__);
irda_usb_change_speed_xbofs(self);
} else {
/* New speed and xbof is now commited in hardware */
struct urb *urb;
int done = 0; /* If we have made any progress */
- IRDA_DEBUG(0, "%s(), Network layer thinks we timed out!\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), Network layer thinks we timed out!\n", __func__);
IRDA_ASSERT(self != NULL, return;);
/* Protect us from USB callbacks, net Tx and else. */
/* self->present *MUST* be read under spinlock */
if (!self->present) {
- IRDA_WARNING("%s(), device not present!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), device not present!\n", __func__);
netif_stop_queue(netdev);
spin_unlock_irqrestore(&self->lock, flags);
return;
struct irda_skb_cb *cb;
int ret;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* This should never happen */
IRDA_ASSERT(skb != NULL, return;);
/* If this ever happen, we are in deep s***.
* Basically, the Rx path will stop... */
IRDA_WARNING("%s(), Failed to submit Rx URB %d\n",
- __FUNCTION__, ret);
+ __func__, ret);
}
}
struct urb *next_urb;
unsigned int len, docopy;
- IRDA_DEBUG(2, "%s(), len=%d\n", __FUNCTION__, urb->actual_length);
+ IRDA_DEBUG(2, "%s(), len=%d\n", __func__, urb->actual_length);
/* Find ourselves */
cb = (struct irda_skb_cb *) skb->cb;
/* If the network is closed or the device gone, stop everything */
if ((!self->netopen) || (!self->present)) {
- IRDA_DEBUG(0, "%s(), Network is gone!\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), Network is gone!\n", __func__);
/* Don't re-submit the URB : will stall the Rx path */
return;
}
/* Usually precursor to a hot-unplug on OHCI. */
default:
self->stats.rx_errors++;
- IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X \n", __FUNCTION__, urb->status, urb->transfer_flags);
+ IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X \n", __func__, urb->status, urb->transfer_flags);
break;
}
/* If we received an error, we don't want to resubmit the
/* Check for empty frames */
if (urb->actual_length <= self->header_length) {
- IRDA_WARNING("%s(), empty frame!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), empty frame!\n", __func__);
goto done;
}
struct irda_skb_cb *cb;
struct urb *next_urb;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Find ourselves */
cb = (struct irda_skb_cb *) skb->cb;
patch_block, block_size,
&actual_len, msecs_to_jiffies(500));
IRDA_DEBUG(3,"%s(): Bulk send %u bytes, ret=%d\n",
- __FUNCTION__, actual_len, ret);
+ __func__, actual_len, ret);
if (ret < 0)
break;
/* We get a patch from userspace */
IRDA_MESSAGE("%s(): Received firmware %s (%zu bytes)\n",
- __FUNCTION__, stir421x_fw_name, fw->size);
+ __func__, stir421x_fw_name, fw->size);
ret = -EINVAL;
+ (build % 10);
IRDA_DEBUG(3, "%s(): Firmware Product version %ld\n",
- __FUNCTION__, fw_version);
+ __func__, fw_version);
}
}
char hwname[16];
int i;
- IRDA_DEBUG(1, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s()\n", __func__);
IRDA_ASSERT(netdev != NULL, return -1;);
self = (struct irda_usb_cb *) netdev->priv;
/* Can only open the device if it's there */
if(!self->present) {
spin_unlock_irqrestore(&self->lock, flags);
- IRDA_WARNING("%s(), device not present!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), device not present!\n", __func__);
return -1;
}
if(self->needspatch) {
spin_unlock_irqrestore(&self->lock, flags);
- IRDA_WARNING("%s(), device needs patch\n", __FUNCTION__) ;
+ IRDA_WARNING("%s(), device needs patch\n", __func__) ;
return -EIO ;
}
/* If this ever happen, we are in deep s***.
* Basically, we can't start the Rx path... */
IRDA_WARNING("%s(), Failed to allocate Rx skb\n",
- __FUNCTION__);
+ __func__);
return -1;
}
//skb_reserve(newskb, USB_IRDA_HEADER - 1);
struct irda_usb_cb *self;
int i;
- IRDA_DEBUG(1, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s()\n", __func__);
IRDA_ASSERT(netdev != NULL, return -1;);
self = (struct irda_usb_cb *) netdev->priv;
self = dev->priv;
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd);
+ IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
switch (cmd) {
case SIOCSBANDWIDTH: /* Set bandwidth */
{
struct irda_class_desc *desc;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
desc = self->irda_desc;
self->qos.data_size.bits = desc->bmDataSize;
IRDA_DEBUG(0, "%s(), dongle says speed=0x%X, size=0x%X, window=0x%X, bofs=0x%X, turn=0x%X\n",
- __FUNCTION__, self->qos.baud_rate.bits, self->qos.data_size.bits, self->qos.window_size.bits, self->qos.additional_bofs.bits, self->qos.min_turn_time.bits);
+ __func__, self->qos.baud_rate.bits, self->qos.data_size.bits, self->qos.window_size.bits, self->qos.additional_bofs.bits, self->qos.min_turn_time.bits);
/* Don't always trust what the dongle tell us */
if(self->capability & IUC_SIR_ONLY)
{
struct net_device *netdev = self->netdev;
- IRDA_DEBUG(1, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s()\n", __func__);
irda_usb_init_qos(self);
*/
static inline void irda_usb_close(struct irda_usb_cb *self)
{
- IRDA_DEBUG(1, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s()\n", __func__);
/* Remove netdevice */
unregister_netdev(self->netdev);
/* This is our interrupt endpoint */
self->bulk_int_ep = ep;
} else {
- IRDA_ERROR("%s(), Unrecognised endpoint %02X.\n", __FUNCTION__, ep);
+ IRDA_ERROR("%s(), Unrecognised endpoint %02X.\n", __func__, ep);
}
}
}
IRDA_DEBUG(0, "%s(), And our endpoints are : in=%02X, out=%02X (%d), int=%02X\n",
- __FUNCTION__, self->bulk_in_ep, self->bulk_out_ep, self->bulk_out_mtu, self->bulk_int_ep);
+ __func__, self->bulk_in_ep, self->bulk_out_ep, self->bulk_out_mtu, self->bulk_int_ep);
return((self->bulk_in_ep != 0) && (self->bulk_out_ep != 0));
}
0, intf->altsetting->desc.bInterfaceNumber, desc,
sizeof(*desc), 500);
- IRDA_DEBUG(1, "%s(), ret=%d\n", __FUNCTION__, ret);
+ IRDA_DEBUG(1, "%s(), ret=%d\n", __func__, ret);
if (ret < sizeof(*desc)) {
IRDA_WARNING("usb-irda: class_descriptor read %s (%d)\n",
(ret<0) ? "failed" : "too short", ret);
/* Martin Diehl says if we get a -EPIPE we should
* be fine and we don't need to do a usb_clear_halt().
* - Jean II */
- IRDA_DEBUG(0, "%s(), Received -EPIPE, ignoring...\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), Received -EPIPE, ignoring...\n", __func__);
break;
default:
- IRDA_DEBUG(0, "%s(), Unknown error %d\n", __FUNCTION__, ret);
+ IRDA_DEBUG(0, "%s(), Unknown error %d\n", __func__, ret);
ret = -EIO;
goto err_out_3;
}
interface = intf->cur_altsetting;
if(!irda_usb_parse_endpoints(self, interface->endpoint,
interface->desc.bNumEndpoints)) {
- IRDA_ERROR("%s(), Bogus endpoints...\n", __FUNCTION__);
+ IRDA_ERROR("%s(), Bogus endpoints...\n", __func__);
ret = -EIO;
goto err_out_3;
}
struct irda_usb_cb *self = usb_get_intfdata(intf);
int i;
- IRDA_DEBUG(1, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s()\n", __func__);
usb_set_intfdata(intf, NULL);
if (!self)
/* Free self and network device */
free_netdev(self->netdev);
- IRDA_DEBUG(0, "%s(), USB IrDA Disconnected\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), USB IrDA Disconnected\n", __func__);
}
/*------------------------------------------------------------------*/
dev = priv->dev;
if (!dev) {
- IRDA_WARNING("%s(), not ready yet!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), not ready yet!\n", __func__);
return;
}
IRDA_ASSERT(priv != NULL, return -ENODEV;);
IRDA_ASSERT(priv->magic == IRTTY_MAGIC, return -EBADR;);
- IRDA_DEBUG(3, "%s(cmd=0x%X)\n", __FUNCTION__, cmd);
+ IRDA_DEBUG(3, "%s(cmd=0x%X)\n", __func__, cmd);
dev = priv->dev;
IRDA_ASSERT(dev != NULL, return -1;);
mutex_unlock(&irtty_mutex);
- IRDA_DEBUG(0, "%s - %s: irda line discipline opened\n", __FUNCTION__, tty->name);
+ IRDA_DEBUG(0, "%s - %s: irda line discipline opened\n", __func__, tty->name);
return 0;
kfree(priv);
- IRDA_DEBUG(0, "%s - %s: irda line discipline closed\n", __FUNCTION__, tty->name);
+ IRDA_DEBUG(0, "%s - %s: irda line discipline closed\n", __func__, tty->name);
}
/* ------------------------------------------------------- */
if ((err = tty_unregister_ldisc(N_IRDA))) {
IRDA_ERROR("%s(), can't unregister line discipline (err = %d)\n",
- __FUNCTION__, err);
+ __func__, err);
}
}
}
} else if (urb->actual_length > 0) {
err("%s(): Unexpected response length, expected %d got %d",
- __FUNCTION__, kingsun->max_rx, urb->actual_length);
+ __func__, kingsun->max_rx, urb->actual_length);
}
/* This urb has already been filled in kingsun_net_open */
ret = usb_submit_urb(urb, GFP_ATOMIC);
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power up dongle */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int litelink_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
{
int i;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* dongle already reset by irda-thread - current speed (dongle and
* port) is the default speed (115200 for litelink!)
*/
static int litelink_reset(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* probably the power-up can be dropped here, but with only
* 15 usec delay it's not worth the risk unless somebody with
static int __init ma600_sir_init(void)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
return irda_register_dongle(&ma600);
}
static void __exit ma600_sir_cleanup(void)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
irda_unregister_dongle(&ma600);
}
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int ma600_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
{
u8 byte;
- IRDA_DEBUG(2, "%s(), speed=%d (was %d)\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), speed=%d (was %d)\n", __func__,
speed, dev->speed);
/* dongle already reset, dongle and port at default speed (9600) */
sirdev_raw_read(dev, &byte, sizeof(byte));
if (byte != get_control_byte(speed)) {
IRDA_WARNING("%s(): bad control byte read-back %02x != %02x\n",
- __FUNCTION__, (unsigned) byte,
+ __func__, (unsigned) byte,
(unsigned) get_control_byte(speed));
return -1;
}
else
- IRDA_DEBUG(2, "%s() control byte write read OK\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s() control byte write read OK\n", __func__);
#endif
/* Set DTR, Set RTS */
int ma600_reset(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Reset the dongle : set DTR low for 10 ms */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* seems no explicit power-on required here and reset switching it on anyway */
static int mcp2120_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
/* reset and inhibit mcp2120 */
u8 control[2];
static int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
switch (state) {
case SIRDEV_STATE_DONGLE_SPEED:
break;
default:
- IRDA_ERROR("%s(), undefine state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s(), undefine state %d\n", __func__, state);
ret = -EINVAL;
break;
}
unsigned delay = 0;
int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
switch (state) {
case SIRDEV_STATE_DONGLE_RESET:
break;
default:
- IRDA_ERROR("%s(), undefined state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s(), undefined state %d\n", __func__, state);
ret = -EINVAL;
break;
}
static chipio_t pnp_info;
static const struct pnp_device_id nsc_ircc_pnp_table[] = {
{ .id = "NSC6001", .driver_data = 0 },
- { .id = "IBM0071", .driver_data = 0 },
{ .id = "HWPC224", .driver_data = 0 },
+ { .id = "IBM0071", .driver_data = NSC_FORCE_DONGLE_TYPE9 },
{ }
};
/* Probe for all the NSC chipsets we know about */
for (chip = chips; chip->name ; chip++) {
- IRDA_DEBUG(2, "%s(), Probing for %s ...\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), Probing for %s ...\n", __func__,
chip->name);
/* Try all config registers for this chip */
/* Read index register */
reg = inb(cfg_base);
if (reg == 0xff) {
- IRDA_DEBUG(2, "%s() no chip at 0x%03x\n", __FUNCTION__, cfg_base);
+ IRDA_DEBUG(2, "%s() no chip at 0x%03x\n", __func__, cfg_base);
continue;
}
id = inb(cfg_base+1);
if ((id & chip->cid_mask) == chip->cid_value) {
IRDA_DEBUG(2, "%s() Found %s chip, revision=%d\n",
- __FUNCTION__, chip->name, id & ~chip->cid_mask);
+ __func__, chip->name, id & ~chip->cid_mask);
/*
* If we found a correct PnP setting,
}
i++;
} else {
- IRDA_DEBUG(2, "%s(), Wrong chip id=0x%02x\n", __FUNCTION__, id);
+ IRDA_DEBUG(2, "%s(), Wrong chip id=0x%02x\n", __func__, id);
}
}
}
void *ret;
int err, chip_index;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
for (chip_index = 0; chip_index < ARRAY_SIZE(dev_self); chip_index++) {
}
if (chip_index == ARRAY_SIZE(dev_self)) {
- IRDA_ERROR("%s(), maximum number of supported chips reached!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), maximum number of supported chips reached!\n", __func__);
return -ENOMEM;
}
dev = alloc_irdadev(sizeof(struct nsc_ircc_cb));
if (dev == NULL) {
IRDA_ERROR("%s(), can't allocate memory for "
- "control block!\n", __FUNCTION__);
+ "control block!\n", __func__);
return -ENOMEM;
}
ret = request_region(self->io.fir_base, self->io.fir_ext, driver_name);
if (!ret) {
IRDA_WARNING("%s(), can't get iobase of 0x%03x\n",
- __FUNCTION__, self->io.fir_base);
+ __func__, self->io.fir_base);
err = -ENODEV;
goto out1;
}
err = register_netdev(dev);
if (err) {
- IRDA_ERROR("%s(), register_netdev() failed!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), register_netdev() failed!\n", __func__);
goto out4;
}
IRDA_MESSAGE("IrDA: Registered device %s\n", dev->name);
{
int iobase;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s()\n", __func__);
IRDA_ASSERT(self != NULL, return -1;);
/* Release the PORT that this driver is using */
IRDA_DEBUG(4, "%s(), Releasing Region %03x\n",
- __FUNCTION__, self->io.fir_base);
+ __func__, self->io.fir_base);
release_region(self->io.fir_base, self->io.fir_ext);
if (self->tx_buff.head)
case 0x2e8: outb(0x15, cfg_base+1); break;
case 0x3f8: outb(0x16, cfg_base+1); break;
case 0x2f8: outb(0x17, cfg_base+1); break;
- default: IRDA_ERROR("%s(), invalid base_address", __FUNCTION__);
+ default: IRDA_ERROR("%s(), invalid base_address", __func__);
}
/* Control Signal Routing Register (CSRT) */
case 9: temp = 0x05; break;
case 11: temp = 0x06; break;
case 15: temp = 0x07; break;
- default: IRDA_ERROR("%s(), invalid irq", __FUNCTION__);
+ default: IRDA_ERROR("%s(), invalid irq", __func__);
}
outb(CFG_108_CSRT, cfg_base);
case 0: outb(0x08+temp, cfg_base+1); break;
case 1: outb(0x10+temp, cfg_base+1); break;
case 3: outb(0x18+temp, cfg_base+1); break;
- default: IRDA_ERROR("%s(), invalid dma", __FUNCTION__);
+ default: IRDA_ERROR("%s(), invalid dma", __func__);
}
outb(CFG_108_MCTL, cfg_base); /* Mode Control Register (MCTL) */
break;
}
info->sir_base = info->fir_base;
- IRDA_DEBUG(2, "%s(), probing fir_base=0x%03x\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(), probing fir_base=0x%03x\n", __func__,
info->fir_base);
/* Read control signals routing register (CSRT) */
info->irq = 15;
break;
}
- IRDA_DEBUG(2, "%s(), probing irq=%d\n", __FUNCTION__, info->irq);
+ IRDA_DEBUG(2, "%s(), probing irq=%d\n", __func__, info->irq);
/* Currently we only read Rx DMA but it will also be used for Tx */
switch ((reg >> 3) & 0x03) {
info->dma = 3;
break;
}
- IRDA_DEBUG(2, "%s(), probing dma=%d\n", __FUNCTION__, info->dma);
+ IRDA_DEBUG(2, "%s(), probing dma=%d\n", __func__, info->dma);
/* Read mode control register (MCTL) */
outb(CFG_108_MCTL, cfg_base);
/* User is sure about his config... accept it. */
IRDA_DEBUG(2, "%s(): nsc_ircc_init_39x (user settings): "
"io=0x%04x, irq=%d, dma=%d\n",
- __FUNCTION__, info->fir_base, info->irq, info->dma);
+ __func__, info->fir_base, info->irq, info->dma);
/* Access bank for SP2 */
outb(CFG_39X_LDN, cfg_base);
int enabled, susp;
IRDA_DEBUG(2, "%s(), nsc_ircc_probe_39x, base=%d\n",
- __FUNCTION__, cfg_base);
+ __func__, cfg_base);
/* This function should be executed with irq off to avoid
* another driver messing with the Super I/O bank - Jean II */
outb(CFG_39X_SPC, cfg_base);
susp = 1 - ((inb(cfg_base+1) & 0x02) >> 1);
- IRDA_DEBUG(2, "%s(): io=0x%02x%02x, irq=%d (type %d), rxdma=%d, txdma=%d, enabled=%d (suspended=%d)\n", __FUNCTION__, reg1,reg2,irq,irqt,dma1,dma2,enabled,susp);
+ IRDA_DEBUG(2, "%s(): io=0x%02x%02x, irq=%d (type %d), rxdma=%d, txdma=%d, enabled=%d (suspended=%d)\n", __func__, reg1,reg2,irq,irqt,dma1,dma2,enabled,susp);
/* Configure SP2 */
pnp_info.dma = -1;
pnp_succeeded = 1;
- /* There don't seem to be any way to get the cfg_base.
+ if (id->driver_data & NSC_FORCE_DONGLE_TYPE9)
+ dongle_id = 0x9;
+
+ /* There doesn't seem to be any way of getting the cfg_base.
* On my box, cfg_base is in the PnP descriptor of the
* motherboard. Oh well... Jean II */
pnp_info.dma = pnp_dma(dev, 0);
IRDA_DEBUG(0, "%s() : From PnP, found firbase 0x%03X ; irq %d ; dma %d.\n",
- __FUNCTION__, pnp_info.fir_base, pnp_info.irq, pnp_info.dma);
+ __func__, pnp_info.fir_base, pnp_info.irq, pnp_info.dma);
if((pnp_info.fir_base == 0) ||
(pnp_info.irq == -1) || (pnp_info.dma == -1)) {
version = inb(iobase+MID);
IRDA_DEBUG(2, "%s() Driver %s Found chip version %02x\n",
- __FUNCTION__, driver_name, version);
+ __func__, driver_name, version);
/* Should be 0x2? */
if (0x20 != (version & 0xf0)) {
case 0x00: /* same as */
case 0x01: /* Differential serial interface */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x02: /* same as */
case 0x03: /* Reserved */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x04: /* Sharp RY5HD01 */
break;
case 0x05: /* Reserved, but this is what the Thinkpad reports */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x06: /* Single-ended serial interface */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x07: /* Consumer-IR only */
IRDA_DEBUG(0, "%s(), %s is not for IrDA mode\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x08: /* HP HSDL-2300, HP HSDL-3600/HSDL-3610 */
IRDA_DEBUG(0, "%s(), %s\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x09: /* IBM31T1100 or Temic TFDS6000/TFDS6500 */
outb(0x28, iobase+7); /* Set irsl[0-2] as output */
case 0x0A: /* same as */
case 0x0B: /* Reserved */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x0C: /* same as */
case 0x0D: /* HP HSDL-1100/HSDL-2100 */
break;
case 0x0F: /* No dongle connected */
IRDA_DEBUG(0, "%s(), %s\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
switch_bank(iobase, BANK0);
outb(0x62, iobase+MCR);
break;
default:
IRDA_DEBUG(0, "%s(), invalid dongle_id %#x",
- __FUNCTION__, dongle_id);
+ __func__, dongle_id);
}
/* IRCFG1: IRSL1 and 2 are set to IrDA mode */
case 0x00: /* same as */
case 0x01: /* Differential serial interface */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x02: /* same as */
case 0x03: /* Reserved */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x04: /* Sharp RY5HD01 */
break;
case 0x05: /* Reserved */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x06: /* Single-ended serial interface */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x07: /* Consumer-IR only */
IRDA_DEBUG(0, "%s(), %s is not for IrDA mode\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x08: /* HP HSDL-2300, HP HSDL-3600/HSDL-3610 */
IRDA_DEBUG(0, "%s(), %s\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
outb(0x00, iobase+4);
if (speed > 115200)
outb(0x01, iobase+4);
case 0x0A: /* same as */
case 0x0B: /* Reserved */
IRDA_DEBUG(0, "%s(), %s not defined by irda yet\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
break;
case 0x0C: /* same as */
case 0x0D: /* HP HSDL-1100/HSDL-2100 */
break;
case 0x0F: /* No dongle connected */
IRDA_DEBUG(0, "%s(), %s is not for IrDA mode\n",
- __FUNCTION__, dongle_types[dongle_id]);
+ __func__, dongle_types[dongle_id]);
switch_bank(iobase, BANK0);
outb(0x62, iobase+MCR);
break;
default:
- IRDA_DEBUG(0, "%s(), invalid data_rate\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), invalid data_rate\n", __func__);
}
/* Restore bank register */
outb(bank, iobase+BSR);
__u8 bank;
__u8 ier; /* Interrupt enable register */
- IRDA_DEBUG(2, "%s(), speed=%d\n", __FUNCTION__, speed);
+ IRDA_DEBUG(2, "%s(), speed=%d\n", __func__, speed);
IRDA_ASSERT(self != NULL, return 0;);
outb(inb(iobase+4) | 0x04, iobase+4);
mcr = MCR_MIR;
- IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __func__);
break;
case 1152000:
mcr = MCR_MIR;
- IRDA_DEBUG(0, "%s(), handling baud of 1152000\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), handling baud of 1152000\n", __func__);
break;
case 4000000:
mcr = MCR_FIR;
- IRDA_DEBUG(0, "%s(), handling baud of 4000000\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), handling baud of 4000000\n", __func__);
break;
default:
mcr = MCR_FIR;
IRDA_DEBUG(0, "%s(), unknown baud rate of %d\n",
- __FUNCTION__, speed);
+ __func__, speed);
break;
}
int actual = 0;
__u8 bank;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s()\n", __func__);
/* Save current bank */
bank = inb(iobase+BSR);
switch_bank(iobase, BANK0);
if (!(inb_p(iobase+LSR) & LSR_TXEMP)) {
IRDA_DEBUG(4, "%s(), warning, FIFO not empty yet!\n",
- __FUNCTION__);
+ __func__);
/* FIFO may still be filled to the Tx interrupt threshold */
fifo_size -= 17;
}
IRDA_DEBUG(4, "%s(), fifo_size %d ; %d sent of %d\n",
- __FUNCTION__, fifo_size, actual, len);
+ __func__, fifo_size, actual, len);
/* Restore bank */
outb(bank, iobase+BSR);
__u8 bank;
int ret = TRUE;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
iobase = self->io.fir_base;
len = inb(iobase+RFLFL) | ((inb(iobase+RFLFH) & 0x1f) << 8);
if (st_fifo->tail >= MAX_RX_WINDOW) {
- IRDA_DEBUG(0, "%s(), window is full!\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), window is full!\n", __func__);
continue;
}
if (skb == NULL) {
IRDA_WARNING("%s(), memory squeeze, "
"dropping frame.\n",
- __FUNCTION__);
+ __func__);
self->stats.rx_dropped++;
/* Restore bank register */
* Need to be after self->io.direction to avoid race with
* nsc_ircc_hard_xmit_sir() - Jean II */
if (self->new_speed) {
- IRDA_DEBUG(2, "%s(), Changing speed!\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), Changing speed!\n", __func__);
self->ier = nsc_ircc_change_speed(self,
self->new_speed);
self->new_speed = 0;
} else
IRDA_WARNING("%s(), potential "
"Tx queue lockup !\n",
- __FUNCTION__);
+ __func__);
}
} else {
/* Not finished yet, so interrupt on DMA again */
char hwname[32];
__u8 bank;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s()\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
self = (struct nsc_ircc_cb *) dev->priv;
int iobase;
__u8 bank;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s()\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd);
+ IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
switch (cmd) {
case SIOCSBANDWIDTH: /* Set bandwidth */
#include <linux/types.h>
#include <asm/io.h>
+/* Features for chips (set in driver_data) */
+#define NSC_FORCE_DONGLE_TYPE9 0x00000001
+
/* DMA modes needed */
#define DMA_TX_MODE 0x08 /* Mem to I/O, ++, demand. */
#define DMA_RX_MODE 0x04 /* I/O to mem, ++, demand. */
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power on dongle */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int old_belkin_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
*/
static int old_belkin_change_speed(struct sir_dev *dev, unsigned speed)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
dev->speed = 9600;
return (speed==dev->speed) ? 0 : -EINVAL;
*/
static int old_belkin_reset(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* This dongles speed "defaults" to 9600 bps ;-) */
dev->speed = 9600;
#include <net/irda/irda_device.h>
#include <asm/dma.h>
-#include <asm/arch/irda.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/irda.h>
+#include <mach/pxa-regs.h>
#define IrSR_RXPL_NEG_IS_ZERO (1<<4)
#define IrSR_RXPL_POS_IS_ZERO 0x0
#include <asm/irq.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/irda.h>
static int power_level = 3;
return 0;
default:
- IRDA_ERROR("%s - undefined state\n", __FUNCTION__);
+ IRDA_ERROR("%s - undefined state\n", __func__);
return -EINVAL;
}
fsm->substate = next_state;
int ret = -1;
unsigned delay;
- IRDA_DEBUG(2, "%s(), <%ld>\n", __FUNCTION__, jiffies);
+ IRDA_DEBUG(2, "%s(), <%ld>\n", __func__, jiffies);
do {
IRDA_DEBUG(3, "%s - state=0x%04x / substate=0x%04x\n",
- __FUNCTION__, fsm->state, fsm->substate);
+ __func__, fsm->state, fsm->substate);
next_state = fsm->state;
delay = 0;
break;
default:
- IRDA_ERROR("%s - undefined state\n", __FUNCTION__);
+ IRDA_ERROR("%s - undefined state\n", __func__);
fsm->result = -EINVAL;
/* fall thru */
case SIRDEV_STATE_ERROR:
- IRDA_ERROR("%s - error: %d\n", __FUNCTION__, fsm->result);
+ IRDA_ERROR("%s - error: %d\n", __func__, fsm->result);
#if 0 /* don't enable this before we have netdev->tx_timeout to recover */
netif_stop_queue(dev->netdev);
{
struct sir_fsm *fsm = &dev->fsm;
- IRDA_DEBUG(2, "%s - state=0x%04x / param=%u\n", __FUNCTION__, initial_state, param);
+ IRDA_DEBUG(2, "%s - state=0x%04x / param=%u\n", __func__,
+ initial_state, param);
if (down_trylock(&fsm->sem)) {
if (in_interrupt() || in_atomic() || irqs_disabled()) {
- IRDA_DEBUG(1, "%s(), state machine busy!\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s(), state machine busy!\n", __func__);
return -EWOULDBLOCK;
} else
down(&fsm->sem);
if (fsm->state == SIRDEV_STATE_DEAD) {
/* race with sirdev_close should never happen */
- IRDA_ERROR("%s(), instance staled!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), instance staled!\n", __func__);
up(&fsm->sem);
return -ESTALE; /* or better EPIPE? */
}
{
int err;
- IRDA_DEBUG(3, "%s : requesting dongle %d.\n", __FUNCTION__, type);
+ IRDA_DEBUG(3, "%s : requesting dongle %d.\n", __func__, type);
err = sirdev_schedule_dongle_open(dev, type);
if (unlikely(err))
ret = dev->drv->do_write(dev, dev->tx_buff.data, dev->tx_buff.len);
if (ret > 0) {
- IRDA_DEBUG(3, "%s(), raw-tx started\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s(), raw-tx started\n", __func__);
dev->tx_buff.data += ret;
dev->tx_buff.len -= ret;
spin_lock_irqsave(&dev->tx_lock, flags);
IRDA_DEBUG(3, "%s() - dev->tx_buff.len = %d\n",
- __FUNCTION__, dev->tx_buff.len);
+ __func__, dev->tx_buff.len);
if (likely(dev->tx_buff.len > 0)) {
/* Write data left in transmit buffer */
else if (unlikely(actual<0)) {
/* could be dropped later when we have tx_timeout to recover */
IRDA_ERROR("%s: drv->do_write failed (%d)\n",
- __FUNCTION__, actual);
+ __func__, actual);
if ((skb=dev->tx_skb) != NULL) {
dev->tx_skb = NULL;
dev_kfree_skb_any(skb);
* restarted when the irda-thread has completed the request.
*/
- IRDA_DEBUG(3, "%s(), raw-tx done\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s(), raw-tx done\n", __func__);
dev->raw_tx = 0;
goto done; /* no post-frame handling in raw mode */
}
* re-activated.
*/
- IRDA_DEBUG(5, "%s(), finished with frame!\n", __FUNCTION__);
+ IRDA_DEBUG(5, "%s(), finished with frame!\n", __func__);
if ((skb=dev->tx_skb) != NULL) {
dev->tx_skb = NULL;
}
if (unlikely(dev->new_speed > 0)) {
- IRDA_DEBUG(5, "%s(), Changing speed!\n", __FUNCTION__);
+ IRDA_DEBUG(5, "%s(), Changing speed!\n", __func__);
err = sirdev_schedule_speed(dev, dev->new_speed);
if (unlikely(err)) {
/* should never happen
* forget the speed change and hope the stack recovers
*/
IRDA_ERROR("%s - schedule speed change failed: %d\n",
- __FUNCTION__, err);
+ __func__, err);
netif_wake_queue(dev->netdev);
}
/* else: success
int sirdev_receive(struct sir_dev *dev, const unsigned char *cp, size_t count)
{
if (!dev || !dev->netdev) {
- IRDA_WARNING("%s(), not ready yet!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), not ready yet!\n", __func__);
return -1;
}
if (!dev->irlap) {
IRDA_WARNING("%s - too early: %p / %zd!\n",
- __FUNCTION__, cp, count);
+ __func__, cp, count);
return -1;
}
*/
irda_device_set_media_busy(dev->netdev, TRUE);
dev->stats.rx_dropped++;
- IRDA_DEBUG(0, "%s; rx-drop: %zd\n", __FUNCTION__, count);
+ IRDA_DEBUG(0, "%s; rx-drop: %zd\n", __func__, count);
return 0;
}
netif_stop_queue(ndev);
- IRDA_DEBUG(3, "%s(), skb->len = %d\n", __FUNCTION__, skb->len);
+ IRDA_DEBUG(3, "%s(), skb->len = %d\n", __func__, skb->len);
speed = irda_get_next_speed(skb);
if ((speed != dev->speed) && (speed != -1)) {
/* Check problems */
if(spin_is_locked(&dev->tx_lock)) {
- IRDA_DEBUG(3, "%s(), write not completed\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s(), write not completed\n", __func__);
}
/* serialize with write completion */
else if (unlikely(actual < 0)) {
/* could be dropped later when we have tx_timeout to recover */
IRDA_ERROR("%s: drv->do_write failed (%d)\n",
- __FUNCTION__, actual);
+ __func__, actual);
dev_kfree_skb_any(skb);
dev->stats.tx_errors++;
dev->stats.tx_dropped++;
IRDA_ASSERT(dev != NULL, return -1;);
- IRDA_DEBUG(3, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, ndev->name, cmd);
+ IRDA_DEBUG(3, "%s(), %s, (cmd=0x%X)\n", __func__, ndev->name, cmd);
switch (cmd) {
case SIOCSBANDWIDTH: /* Set bandwidth */
if (!try_module_get(drv->owner))
return -ESTALE;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
if (sirdev_alloc_buffers(dev))
goto errout_dec;
netif_wake_queue(ndev);
- IRDA_DEBUG(2, "%s - done, speed = %d\n", __FUNCTION__, dev->speed);
+ IRDA_DEBUG(2, "%s - done, speed = %d\n", __func__, dev->speed);
return 0;
struct sir_dev *dev = ndev->priv;
const struct sir_driver *drv;
-// IRDA_DEBUG(0, "%s\n", __FUNCTION__);
+// IRDA_DEBUG(0, "%s\n", __func__);
netif_stop_queue(ndev);
struct net_device *ndev;
struct sir_dev *dev;
- IRDA_DEBUG(0, "%s - %s\n", __FUNCTION__, name);
+ IRDA_DEBUG(0, "%s - %s\n", __func__, name);
/* instead of adding tests to protect against drv->do_write==NULL
* at several places we refuse to create a sir_dev instance for
*/
ndev = alloc_irdadev(sizeof(*dev));
if (ndev == NULL) {
- IRDA_ERROR("%s - Can't allocate memory for IrDA control block!\n", __FUNCTION__);
+ IRDA_ERROR("%s - Can't allocate memory for IrDA control block!\n", __func__);
goto out;
}
dev = ndev->priv;
ndev->do_ioctl = sirdev_ioctl;
if (register_netdev(ndev)) {
- IRDA_ERROR("%s(), register_netdev() failed!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), register_netdev() failed!\n", __func__);
goto out_freenetdev;
}
{
int err = 0;
- IRDA_DEBUG(0, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s\n", __func__);
atomic_set(&dev->enable_rx, 0);
if (dev->dongle_drv)
err = sirdev_schedule_dongle_close(dev);
if (err)
- IRDA_ERROR("%s - error %d\n", __FUNCTION__, err);
+ IRDA_ERROR("%s - error %d\n", __func__, err);
sirdev_close(dev->netdev);
struct dongle_driver *drv;
IRDA_DEBUG(0, "%s : registering dongle \"%s\" (%d).\n",
- __FUNCTION__, new->driver_name, new->type);
+ __func__, new->driver_name, new->type);
mutex_lock(&dongle_list_lock);
list_for_each(entry, &dongle_list) {
{
int ret;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
ret = platform_driver_register(&smsc_ircc_driver);
if (ret) {
struct net_device *dev;
int err;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
err = smsc_ircc_present(fir_base, sir_base);
if (err)
err = -ENOMEM;
if (dev_count >= ARRAY_SIZE(dev_self)) {
- IRDA_WARNING("%s(), too many devices!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), too many devices!\n", __func__);
goto err_out1;
}
*/
dev = alloc_irdadev(sizeof(struct smsc_ircc_cb));
if (!dev) {
- IRDA_WARNING("%s() can't allocate net device\n", __FUNCTION__);
+ IRDA_WARNING("%s() can't allocate net device\n", __func__);
goto err_out1;
}
if (!request_region(fir_base, SMSC_IRCC2_FIR_CHIP_IO_EXTENT,
driver_name)) {
IRDA_WARNING("%s: can't get fir_base of 0x%03x\n",
- __FUNCTION__, fir_base);
+ __func__, fir_base);
goto out1;
}
if (!request_region(sir_base, SMSC_IRCC2_SIR_CHIP_IO_EXTENT,
driver_name)) {
IRDA_WARNING("%s: can't get sir_base of 0x%03x\n",
- __FUNCTION__, sir_base);
+ __func__, sir_base);
goto out2;
}
if (high != 0x10 || low != 0xb8 || (chip != 0xf1 && chip != 0xf2)) {
IRDA_WARNING("%s(), addr 0x%04x - no device found!\n",
- __FUNCTION__, fir_base);
+ __func__, fir_base);
goto out3;
}
IRDA_MESSAGE("SMsC IrDA Controller found\n IrCC version %d.%d, "
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name, cmd);
+ IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
switch (cmd) {
case SIOCSBANDWIDTH: /* Set bandwidth */
unsigned long flags;
s32 speed;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(dev != NULL, return 0;);
ir_mode = IRCC_CFGA_IRDA_HDLC;
ctrl = IRCC_CRC;
fast = 0;
- IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __func__);
break;
case 1152000:
ir_mode = IRCC_CFGA_IRDA_HDLC;
ctrl = IRCC_1152 | IRCC_CRC;
fast = IRCC_LCR_A_FAST | IRCC_LCR_A_GP_DATA;
IRDA_DEBUG(0, "%s(), handling baud of 1152000\n",
- __FUNCTION__);
+ __func__);
break;
case 4000000:
ir_mode = IRCC_CFGA_IRDA_4PPM;
ctrl = IRCC_CRC;
fast = IRCC_LCR_A_FAST;
IRDA_DEBUG(0, "%s(), handling baud of 4000000\n",
- __FUNCTION__);
+ __func__);
break;
}
#if 0
struct net_device *dev;
int fir_base;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(self != NULL, return;);
dev = self->netdev;
{
int fir_base;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(self != NULL, return;);
struct net_device *dev;
int last_speed_was_sir;
- IRDA_DEBUG(0, "%s() changing speed to: %d\n", __FUNCTION__, speed);
+ IRDA_DEBUG(0, "%s() changing speed to: %d\n", __func__, speed);
IRDA_ASSERT(self != NULL, return;);
dev = self->netdev;
int lcr; /* Line control reg */
int divisor;
- IRDA_DEBUG(0, "%s(), Setting speed to: %d\n", __FUNCTION__, speed);
+ IRDA_DEBUG(0, "%s(), Setting speed to: %d\n", __func__, speed);
IRDA_ASSERT(self != NULL, return;);
iobase = self->io.sir_base;
/* Turn on interrups */
outb(UART_IER_RLSI | UART_IER_RDI | UART_IER_THRI, iobase + UART_IER);
- IRDA_DEBUG(2, "%s() speed changed to: %d\n", __FUNCTION__, speed);
+ IRDA_DEBUG(2, "%s() speed changed to: %d\n", __func__, speed);
}
int iobase = self->io.fir_base;
u8 ctrl;
- IRDA_DEBUG(3, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s\n", __func__);
#if 1
/* Disable Rx */
register_bank(iobase, 0);
{
int iobase = self->io.fir_base;
- IRDA_DEBUG(3, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s\n", __func__);
#if 0
/* Disable Tx */
register_bank(iobase, 0);
register_bank(iobase, 0);
- IRDA_DEBUG(3, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s\n", __func__);
#if 0
/* Disable Rx */
register_bank(iobase, 0);
lsr= inb(iobase + IRCC_LSR);
msgcnt = inb(iobase + IRCC_LCR_B) & 0x08;
- IRDA_DEBUG(2, "%s: dma count = %d\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s: dma count = %d\n", __func__,
get_dma_residue(self->io.dma));
len = self->rx_buff.truesize - get_dma_residue(self->io.dma);
len -= self->io.speed < 4000000 ? 2 : 4;
if (len < 2 || len > 2050) {
- IRDA_WARNING("%s(), bogus len=%d\n", __FUNCTION__, len);
+ IRDA_WARNING("%s(), bogus len=%d\n", __func__, len);
return;
}
- IRDA_DEBUG(2, "%s: msgcnt = %d, len=%d\n", __FUNCTION__, msgcnt, len);
+ IRDA_DEBUG(2, "%s: msgcnt = %d, len=%d\n", __func__, msgcnt, len);
skb = dev_alloc_skb(len + 1);
if (!skb) {
IRDA_WARNING("%s(), memory squeeze, dropping frame.\n",
- __FUNCTION__);
+ __func__);
return;
}
/* Make sure IP header gets aligned */
/* Make sure we don't stay here to long */
if (boguscount++ > 32) {
- IRDA_DEBUG(2, "%s(), breaking!\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), breaking!\n", __func__);
break;
}
} while (inb(iobase + UART_LSR) & UART_LSR_DR);
lcra = inb(iobase + IRCC_LCR_A);
lsr = inb(iobase + IRCC_LSR);
- IRDA_DEBUG(2, "%s(), iir = 0x%02x\n", __FUNCTION__, iir);
+ IRDA_DEBUG(2, "%s(), iir = 0x%02x\n", __func__, iir);
if (iir & IRCC_IIR_EOM) {
if (self->io.direction == IO_RECV)
}
if (iir & IRCC_IIR_ACTIVE_FRAME) {
- /*printk(KERN_WARNING "%s(): Active Frame\n", __FUNCTION__);*/
+ /*printk(KERN_WARNING "%s(): Active Frame\n", __func__);*/
}
/* Enable interrupts again */
lsr = inb(iobase + UART_LSR);
IRDA_DEBUG(4, "%s(), iir=%02x, lsr=%02x, iobase=%#x\n",
- __FUNCTION__, iir, lsr, iobase);
+ __func__, iir, lsr, iobase);
switch (iir) {
case UART_IIR_RLSI:
- IRDA_DEBUG(2, "%s(), RLSI\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(), RLSI\n", __func__);
break;
case UART_IIR_RDI:
/* Receive interrupt */
break;
default:
IRDA_DEBUG(0, "%s(), unhandled IIR=%#x\n",
- __FUNCTION__, iir);
+ __func__, iir);
break;
}
int status = FALSE;
/* int iobase; */
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(self != NULL, return FALSE;);
- IRDA_DEBUG(0, "%s: dma count = %d\n", __FUNCTION__,
+ IRDA_DEBUG(0, "%s: dma count = %d\n", __func__,
get_dma_residue(self->io.dma));
status = (self->rx_buff.state != OUTSIDE_FRAME);
self->netdev->name, self->netdev);
if (error)
IRDA_DEBUG(0, "%s(), unable to allocate irq=%d, err=%d\n",
- __FUNCTION__, self->io.irq, error);
+ __func__, self->io.irq, error);
return error;
}
struct smsc_ircc_cb *self;
char hwname[16];
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
self = netdev_priv(dev);
IRDA_ASSERT(self != NULL, return 0;);
if (self->io.suspended) {
- IRDA_DEBUG(0, "%s(), device is suspended\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(), device is suspended\n", __func__);
return -EAGAIN;
}
if (request_irq(self->io.irq, smsc_ircc_interrupt, 0, dev->name,
(void *) dev)) {
IRDA_DEBUG(0, "%s(), unable to allocate irq=%d\n",
- __FUNCTION__, self->io.irq);
+ __func__, self->io.irq);
return -EAGAIN;
}
smsc_ircc_net_close(dev);
IRDA_WARNING("%s(), unable to allocate DMA=%d\n",
- __FUNCTION__, self->io.dma);
+ __func__, self->io.dma);
return -EAGAIN;
}
{
struct smsc_ircc_cb *self;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
self = netdev_priv(dev);
*/
static int __exit smsc_ircc_close(struct smsc_ircc_cb *self)
{
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
IRDA_ASSERT(self != NULL, return -1;);
smsc_ircc_stop_interrupts(self);
/* Release the PORTS that this driver is using */
- IRDA_DEBUG(0, "%s(), releasing 0x%03x\n", __FUNCTION__,
+ IRDA_DEBUG(0, "%s(), releasing 0x%03x\n", __func__,
self->io.fir_base);
release_region(self->io.fir_base, self->io.fir_ext);
- IRDA_DEBUG(0, "%s(), releasing 0x%03x\n", __FUNCTION__,
+ IRDA_DEBUG(0, "%s(), releasing 0x%03x\n", __func__,
self->io.sir_base);
release_region(self->io.sir_base, self->io.sir_ext);
{
int i;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
for (i = 0; i < 2; i++) {
if (dev_self[i])
struct net_device *dev;
int fir_base, sir_base;
- IRDA_DEBUG(3, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s\n", __func__);
IRDA_ASSERT(self != NULL, return;);
dev = self->netdev;
/* Turn on interrups */
outb(UART_IER_RLSI | UART_IER_RDI |UART_IER_THRI, sir_base + UART_IER);
- IRDA_DEBUG(3, "%s() - exit\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s() - exit\n", __func__);
outb(0x00, fir_base + IRCC_MASTER);
}
{
int iobase;
- IRDA_DEBUG(3, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s\n", __func__);
iobase = self->io.sir_base;
/* Reset UART */
IRDA_ASSERT(self != NULL, return;);
- IRDA_DEBUG(4, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(4, "%s\n", __func__);
iobase = self->io.sir_base;
*/
if (self->new_speed) {
IRDA_DEBUG(5, "%s(), Changing speed to %d.\n",
- __FUNCTION__, self->new_speed);
+ __func__, self->new_speed);
smsc_ircc_sir_wait_hw_transmitter_finish(self);
smsc_ircc_change_speed(self, self->new_speed);
self->new_speed = 0;
/* Tx FIFO should be empty! */
if (!(inb(iobase + UART_LSR) & UART_LSR_THRE)) {
- IRDA_WARNING("%s(), failed, fifo not empty!\n", __FUNCTION__);
+ IRDA_WARNING("%s(), failed, fifo not empty!\n", __func__);
return 0;
}
udelay(1);
if (count == 0)
- IRDA_DEBUG(0, "%s(): stuck transmitter\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s(): stuck transmitter\n", __func__);
}
while (address->cfg_base) {
cfg_base = address->cfg_base;
- /*printk(KERN_WARNING "%s(): probing: 0x%02x for: 0x%02x\n", __FUNCTION__, cfg_base, address->type);*/
+ /*printk(KERN_WARNING "%s(): probing: 0x%02x for: 0x%02x\n", __func__, cfg_base, address->type);*/
if (address->type & SMSCSIO_TYPE_FDC) {
type = "FDC";
u8 mode, dma, irq;
int ret = -ENODEV;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
if (smsc_ircc_probe(cfgbase, SMSCSIOFLAT_DEVICEID_REG, chips, type) == NULL)
return ret;
outb(SMSCSIOFLAT_UARTMODE0C_REG, cfgbase);
mode = inb(cfgbase + 1);
- /*printk(KERN_WARNING "%s(): mode: 0x%02x\n", __FUNCTION__, mode);*/
+ /*printk(KERN_WARNING "%s(): mode: 0x%02x\n", __func__, mode);*/
if (!(mode & SMSCSIOFLAT_UART2MODE_VAL_IRDA))
- IRDA_WARNING("%s(): IrDA not enabled\n", __FUNCTION__);
+ IRDA_WARNING("%s(): IrDA not enabled\n", __func__);
outb(SMSCSIOFLAT_UART2BASEADDR_REG, cfgbase);
sirbase = inb(cfgbase + 1) << 2;
outb(SMSCSIOFLAT_UARTIRQSELECT_REG, cfgbase);
irq = inb(cfgbase + 1) & SMSCSIOFLAT_UART2IRQSELECT_MASK;
- IRDA_MESSAGE("%s(): fir: 0x%02x, sir: 0x%02x, dma: %02d, irq: %d, mode: 0x%02x\n", __FUNCTION__, firbase, sirbase, dma, irq, mode);
+ IRDA_MESSAGE("%s(): fir: 0x%02x, sir: 0x%02x, dma: %02d, irq: %d, mode: 0x%02x\n", __func__, firbase, sirbase, dma, irq, mode);
if (firbase && smsc_ircc_open(firbase, sirbase, dma, irq) == 0)
ret = 0;
unsigned short fir_io, sir_io;
int ret = -ENODEV;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
if (smsc_ircc_probe(cfg_base, 0x20, chips, type) == NULL)
return ret;
static int __init smsc_access(unsigned short cfg_base, unsigned char reg)
{
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
outb(reg, cfg_base);
return inb(cfg_base) != reg ? -1 : 0;
{
u8 devid, xdevid, rev;
- IRDA_DEBUG(1, "%s\n", __FUNCTION__);
+ IRDA_DEBUG(1, "%s\n", __func__);
/* Leave configuration */
if (!request_region(cfg_base, 2, driver_name)) {
IRDA_WARNING("%s: can't get cfg_base of 0x%03x\n",
- __FUNCTION__, cfg_base);
+ __func__, cfg_base);
} else {
if (!smsc_superio_flat(fdc_chips_flat, cfg_base, "FDC") ||
!smsc_superio_paged(fdc_chips_paged, cfg_base, "FDC"))
if (!request_region(cfg_base, 2, driver_name)) {
IRDA_WARNING("%s: can't get cfg_base of 0x%03x\n",
- __FUNCTION__, cfg_base);
+ __func__, cfg_base);
} else {
if (!smsc_superio_flat(lpc_chips_flat, cfg_base, "LPC") ||
!smsc_superio_paged(lpc_chips_paged, cfg_base, "LPC"))
/* empty */;
if (val)
- IRDA_WARNING("%s(): ATC: 0x%02x\n", __FUNCTION__,
+ IRDA_WARNING("%s(): ATC: 0x%02x\n", __func__,
inb(fir_base + IRCC_ATC));
}
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
sirdev_set_dtr_rts(dev, TRUE, TRUE);
static int tekram_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
u8 byte;
static int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
switch(state) {
case SIRDEV_STATE_DONGLE_SPEED:
break;
default:
- IRDA_ERROR("%s - undefined state %d\n", __FUNCTION__, state);
+ IRDA_ERROR("%s - undefined state %d\n", __func__, state);
ret = -EINVAL;
break;
}
static int tekram_reset(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Clear DTR, Set RTS */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
{
struct qos_info *qos = &dev->qos;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Pull the lines high to start with.
*
static int toim3232_close(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Power off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
u8 byte;
static int ret = 0;
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
switch(state) {
case SIRDEV_STATE_DONGLE_SPEED:
break;
default:
- printk(KERN_ERR "%s - undefined state %d\n", __FUNCTION__, state);
+ printk(KERN_ERR "%s - undefined state %d\n", __func__, state);
ret = -EINVAL;
break;
}
static int toim3232_reset(struct sir_dev *dev)
{
- IRDA_DEBUG(2, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s()\n", __func__);
/* Switch off both DTR and RTS to switch off dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
{
int rc;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
rc = pci_register_driver(&via_driver);
if (rc < 0) {
IRDA_DEBUG(0, "%s(): error rc = %d, returning -ENODEV...\n",
- __FUNCTION__, rc);
+ __func__, rc);
return -ENODEV;
}
return 0;
u16 Chipset,FirDRQ1,FirDRQ0,FirIRQ,FirIOBase;
chipio_t info;
- IRDA_DEBUG(2, "%s(): Device ID=(0X%X)\n", __FUNCTION__, id->device);
+ IRDA_DEBUG(2, "%s(): Device ID=(0X%X)\n", __func__, id->device);
rc = pci_enable_device (pcidev);
if (rc) {
- IRDA_DEBUG(0, "%s(): error rc = %d\n", __FUNCTION__, rc);
+ IRDA_DEBUG(0, "%s(): error rc = %d\n", __func__, rc);
return -ENODEV;
}
Chipset=0x3076;
if (Chipset==0x3076) {
- IRDA_DEBUG(2, "%s(): Chipset = 3076\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(): Chipset = 3076\n", __func__);
WriteLPCReg(7,0x0c );
temp=ReadLPCReg(0x30);//check if BIOS Enable Fir
} else
rc = -ENODEV; //IR not turn on
} else { //Not VT1211
- IRDA_DEBUG(2, "%s(): Chipset = 3096\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s(): Chipset = 3096\n", __func__);
pci_read_config_byte(pcidev,0x67,&bTmp);//check if BIOS Enable Fir
if((bTmp&0x01)==1) { // BIOS enable FIR
rc = -ENODEV; //IR not turn on !!!!!
}//Not VT1211
- IRDA_DEBUG(2, "%s(): End - rc = %d\n", __FUNCTION__, rc);
+ IRDA_DEBUG(2, "%s(): End - rc = %d\n", __func__, rc);
return rc;
}
{
int i;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
for (i=0; i < ARRAY_SIZE(dev_self); i++) {
if (dev_self[i])
static void __devexit via_remove_one (struct pci_dev *pdev)
{
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
/* FIXME : This is ugly. We should use pci_get_drvdata(pdev);
* to get our driver instance and call directly via_ircc_close().
static void __exit via_ircc_cleanup(void)
{
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
/* FIXME : This should be redundant, as pci_unregister_driver()
* should call via_remove_one() on each device.
struct via_ircc_cb *self;
int err;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
if (i >= ARRAY_SIZE(dev_self))
return -ENOMEM;
/* Reserve the ioports that we need */
if (!request_region(self->io.fir_base, self->io.fir_ext, driver_name)) {
IRDA_DEBUG(0, "%s(), can't get iobase of 0x%03x\n",
- __FUNCTION__, self->io.fir_base);
+ __func__, self->io.fir_base);
err = -ENODEV;
goto err_out1;
}
{
int iobase;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
IRDA_ASSERT(self != NULL, return -1;);
/* Release the PORT that this driver is using */
IRDA_DEBUG(2, "%s(), Releasing Region %03x\n",
- __FUNCTION__, self->io.fir_base);
+ __func__, self->io.fir_base);
release_region(self->io.fir_base, self->io.fir_ext);
if (self->tx_buff.head)
dma_free_coherent(NULL, self->tx_buff.truesize,
{
int iobase = self->io.fir_base;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
SetMaxRxPacketSize(iobase, 0x0fff); //set to max:4095
// FIFO Init
speed = speed;
IRDA_DEBUG(1, "%s(): change_dongle_speed to %d for 0x%x, %d\n",
- __FUNCTION__, speed, iobase, dongle_id);
+ __func__, speed, iobase, dongle_id);
switch (dongle_id) {
case 0x11: /* Temic TFDS4500 */
- IRDA_DEBUG(2, "%s: Temic TFDS4500: One RX pin, TX normal, RX inverted.\n", __FUNCTION__);
+ IRDA_DEBUG(2, "%s: Temic TFDS4500: One RX pin, TX normal, RX inverted.\n", __func__);
UseOneRX(iobase, ON); //use ONE RX....RX1
InvertTX(iobase, OFF);
SlowIRRXLowActive(iobase, OFF);
} else{
- IRDA_DEBUG(0, "%s: Warning: TFDS4500 not running in SIR mode !\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s: Warning: TFDS4500 not running in SIR mode !\n", __func__);
}
break;
default:
IRDA_ERROR("%s: Error: dongle_id %d unsupported !\n",
- __FUNCTION__, dongle_id);
+ __func__, dongle_id);
}
}
iobase = self->io.fir_base;
/* Update accounting for new speed */
self->io.speed = speed;
- IRDA_DEBUG(1, "%s: change_speed to %d bps.\n", __FUNCTION__, speed);
+ IRDA_DEBUG(1, "%s: change_speed to %d bps.\n", __func__, speed);
WriteReg(iobase, I_ST_CT_0, 0x0);
self->tx_buff.head) + self->tx_buff_dma,
self->tx_fifo.queue[self->tx_fifo.ptr].len, DMA_TX_MODE);
IRDA_DEBUG(1, "%s: tx_fifo.ptr=%x,len=%x,tx_fifo.len=%x..\n",
- __FUNCTION__, self->tx_fifo.ptr,
+ __func__, self->tx_fifo.ptr,
self->tx_fifo.queue[self->tx_fifo.ptr].len,
self->tx_fifo.len);
int ret = TRUE;
u8 Tx_status;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
iobase = self->io.fir_base;
/* Disable DMA */
}
IRDA_DEBUG(1,
"%s: tx_fifo.len=%x ,tx_fifo.ptr=%x,tx_fifo.free=%x...\n",
- __FUNCTION__,
+ __func__,
self->tx_fifo.len, self->tx_fifo.ptr, self->tx_fifo.free);
/* F01_S
// Any frames to be sent back-to-back?
iobase = self->io.fir_base;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
self->tx_fifo.len = self->tx_fifo.ptr = self->tx_fifo.free = 0;
self->tx_fifo.tail = self->tx_buff.head;
return TRUE; //interrupt only, data maybe move by RxT
if (((len - 4) < 2) || ((len - 4) > 2048)) {
IRDA_DEBUG(1, "%s(): Trouble:len=%x,CurCount=%x,LastCount=%x..\n",
- __FUNCTION__, len, RxCurCount(iobase, self),
+ __func__, len, RxCurCount(iobase, self),
self->RxLastCount);
hwreset(self);
return FALSE;
}
IRDA_DEBUG(2, "%s(): fifo.len=%x,len=%x,CurCount=%x..\n",
- __FUNCTION__,
+ __func__,
st_fifo->len, len - 4, RxCurCount(iobase, self));
st_fifo->entries[st_fifo->tail].status = status;
skb_put(skb, len - 4);
skb_copy_to_linear_data(skb, self->rx_buff.data, len - 4);
- IRDA_DEBUG(2, "%s(): len=%x.rx_buff=%p\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(): len=%x.rx_buff=%p\n", __func__,
len - 4, self->rx_buff.data);
// Move to next frame
len = GetRecvByte(iobase, self);
- IRDA_DEBUG(2, "%s(): len=%x\n", __FUNCTION__, len);
+ IRDA_DEBUG(2, "%s(): len=%x\n", __func__, len);
if ((len - 4) < 2) {
self->stats.rx_dropped++;
skb_put(skb, len - 4);
skb_copy_to_linear_data(skb, self->rx_buff.data, len - 4);
- IRDA_DEBUG(2, "%s(): len=%x.head=%x\n", __FUNCTION__,
+ IRDA_DEBUG(2, "%s(): len=%x.head=%x\n", __func__,
len - 4, st_fifo->head);
// Move to next frame
IRDA_DEBUG(2,
"%s(): End of upload HostStatus=%x,RxStatus=%x\n",
- __FUNCTION__,
+ __func__,
GetHostStatus(iobase), GetRXStatus(iobase));
/*
iHostIntType = GetHostStatus(iobase);
IRDA_DEBUG(4, "%s(): iHostIntType %02x: %s %s %s %02x\n",
- __FUNCTION__, iHostIntType,
+ __func__, iHostIntType,
(iHostIntType & 0x40) ? "Timer" : "",
(iHostIntType & 0x20) ? "Tx" : "",
(iHostIntType & 0x10) ? "Rx" : "",
iTxIntType = GetTXStatus(iobase);
IRDA_DEBUG(4, "%s(): iTxIntType %02x: %s %s %s %s\n",
- __FUNCTION__, iTxIntType,
+ __func__, iTxIntType,
(iTxIntType & 0x08) ? "FIFO underr." : "",
(iTxIntType & 0x04) ? "EOM" : "",
(iTxIntType & 0x02) ? "FIFO ready" : "",
iRxIntType = GetRXStatus(iobase);
IRDA_DEBUG(4, "%s(): iRxIntType %02x: %s %s %s %s %s %s %s\n",
- __FUNCTION__, iRxIntType,
+ __func__, iRxIntType,
(iRxIntType & 0x80) ? "PHY err." : "",
(iRxIntType & 0x40) ? "CRC err" : "",
(iRxIntType & 0x20) ? "FIFO overr." : "",
(iRxIntType & 0x02) ? "RxMaxLen" : "",
(iRxIntType & 0x01) ? "SIR bad" : "");
if (!iRxIntType)
- IRDA_DEBUG(3, "%s(): RxIRQ =0\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s(): RxIRQ =0\n", __func__);
if (iRxIntType & 0x10) {
if (via_ircc_dma_receive_complete(self, iobase)) {
} // No ERR
else { //ERR
IRDA_DEBUG(4, "%s(): RxIRQ ERR:iRxIntType=%x,HostIntType=%x,CurCount=%x,RxLastCount=%x_____\n",
- __FUNCTION__, iRxIntType, iHostIntType,
+ __func__, iRxIntType, iHostIntType,
RxCurCount(iobase, self),
self->RxLastCount);
int iobase;
iobase = self->io.fir_base;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
ResetChip(iobase, 5);
EnableDMA(iobase, OFF);
if (CkRxRecv(iobase, self))
status = TRUE;
- IRDA_DEBUG(2, "%s(): status=%x....\n", __FUNCTION__, status);
+ IRDA_DEBUG(2, "%s(): status=%x....\n", __func__, status);
return status;
}
int iobase;
char hwname[32];
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
self = (struct via_ircc_cb *) dev->priv;
struct via_ircc_cb *self;
int iobase;
- IRDA_DEBUG(3, "%s()\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s()\n", __func__);
IRDA_ASSERT(dev != NULL, return -1;);
self = (struct via_ircc_cb *) dev->priv;
IRDA_ASSERT(dev != NULL, return -1;);
self = dev->priv;
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(1, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__, dev->name,
+ IRDA_DEBUG(1, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name,
cmd);
/* Disable interrupts & save flags */
spin_lock_irqsave(&self->lock, flags);
unsigned i;
printk(KERN_DEBUG "%s - ring %p / size %u / mask 0x%04x / len %u / dir %d / hw %p\n",
- __FUNCTION__, r, r->size, r->mask, r->len, r->dir, r->rd[0].hw);
- printk(KERN_DEBUG "%s - head = %d / tail = %d\n", __FUNCTION__,
+ __func__, r, r->size, r->mask, r->len, r->dir, r->rd[0].hw);
+ printk(KERN_DEBUG "%s - head = %d / tail = %d\n", __func__,
atomic_read(&r->head) & r->mask, atomic_read(&r->tail) & r->mask);
for (i = 0; i < r->size; i++) {
rd = &r->rd[i];
- printk(KERN_DEBUG "%s - ring descr %u: ", __FUNCTION__, i);
+ printk(KERN_DEBUG "%s - ring descr %u: ", __func__, i);
printk("skb=%p data=%p hw=%p\n", rd->skb, rd->buf, rd->hw);
printk(KERN_DEBUG "%s - hw: status=%02x count=%u addr=0x%08x\n",
- __FUNCTION__, (unsigned) rd_get_status(rd),
+ __func__, (unsigned) rd_get_status(rd),
(unsigned) rd_get_count(rd), (unsigned) rd_get_addr(rd));
}
}
|| !(busaddr = pci_map_single(pdev, rd->buf, len, dir))) {
if (rd->buf) {
IRDA_ERROR("%s: failed to create PCI-MAP for %p",
- __FUNCTION__, rd->buf);
+ __func__, rd->buf);
kfree(rd->buf);
rd->buf = NULL;
}
ringarea = pci_alloc_consistent(idev->pdev, HW_RING_AREA_SIZE, &idev->busaddr);
if (!ringarea) {
IRDA_ERROR("%s: insufficient memory for descriptor rings\n",
- __FUNCTION__);
+ __func__);
goto out;
}
memset(ringarea, 0, HW_RING_AREA_SIZE);
crclen = (idev->mode==IFF_FIR) ? sizeof(u32) : sizeof(u16);
len -= crclen; /* remove trailing CRC */
if (len <= 0) {
- IRDA_DEBUG(0, "%s: strange frame (len=%d)\n", __FUNCTION__, len);
+ IRDA_DEBUG(0, "%s: strange frame (len=%d)\n", __func__, len);
ret |= VLSI_RX_DROP;
goto done;
}
*/
le16_to_cpus(rd->buf+len);
if (irda_calc_crc16(INIT_FCS,rd->buf,len+crclen) != GOOD_FCS) {
- IRDA_DEBUG(0, "%s: crc error\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s: crc error\n", __func__);
ret |= VLSI_RX_CRC;
goto done;
}
}
if (!rd->skb) {
- IRDA_WARNING("%s: rx packet lost\n", __FUNCTION__);
+ IRDA_WARNING("%s: rx packet lost\n", __func__);
ret |= VLSI_RX_DROP;
goto done;
}
for (rd = ring_last(r); rd != NULL; rd = ring_put(r)) {
if (rd_is_active(rd)) {
IRDA_WARNING("%s: driver bug: rx descr race with hw\n",
- __FUNCTION__);
+ __func__);
vlsi_ring_debug(r);
break;
}
if (ring_first(r) == NULL) {
/* we are in big trouble, if this should ever happen */
- IRDA_ERROR("%s: rx ring exhausted!\n", __FUNCTION__);
+ IRDA_ERROR("%s: rx ring exhausted!\n", __func__);
vlsi_ring_debug(r);
}
else
if (rd_is_active(rd)) {
rd_set_status(rd, 0);
if (rd_get_count(rd)) {
- IRDA_DEBUG(0, "%s - dropping rx packet\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s - dropping rx packet\n", __func__);
ret = -VLSI_RX_DROP;
}
rd_set_count(rd, 0);
int fifocnt;
baudrate = idev->new_baud;
- IRDA_DEBUG(2, "%s: %d -> %d\n", __FUNCTION__, idev->baud, idev->new_baud);
+ IRDA_DEBUG(2, "%s: %d -> %d\n", __func__, idev->baud, idev->new_baud);
if (baudrate == 4000000) {
mode = IFF_FIR;
config = IRCFG_FIR;
switch(baudrate) {
default:
IRDA_WARNING("%s: undefined baudrate %d - fallback to 9600!\n",
- __FUNCTION__, baudrate);
+ __func__, baudrate);
baudrate = 9600;
/* fallthru */
case 2400:
fifocnt = inw(iobase+VLSI_PIO_RCVBCNT) & RCVBCNT_MASK;
if (fifocnt != 0) {
- IRDA_DEBUG(0, "%s: rx fifo not empty(%d)\n", __FUNCTION__, fifocnt);
+ IRDA_DEBUG(0, "%s: rx fifo not empty(%d)\n", __func__, fifocnt);
}
outw(0, iobase+VLSI_PIO_IRENABLE);
config ^= IRENABLE_SIR_ON;
if (config != (IRENABLE_PHYANDCLOCK|IRENABLE_ENRXST)) {
- IRDA_WARNING("%s: failed to set %s mode!\n", __FUNCTION__,
+ IRDA_WARNING("%s: failed to set %s mode!\n", __func__,
(mode==IFF_SIR)?"SIR":((mode==IFF_MIR)?"MIR":"FIR"));
ret = -1;
}
else {
if (inw(iobase+VLSI_PIO_PHYCTL) != nphyctl) {
IRDA_WARNING("%s: failed to apply baudrate %d\n",
- __FUNCTION__, baudrate);
+ __func__, baudrate);
ret = -1;
}
else {
}
if (ret)
- vlsi_reg_debug(iobase,__FUNCTION__);
+ vlsi_reg_debug(iobase,__func__);
return ret;
}
if (len >= r->len-5)
IRDA_WARNING("%s: possible buffer overflow with SIR wrapping!\n",
- __FUNCTION__);
+ __func__);
}
else {
/* hw deals with MIR/FIR mode wrapping */
fifocnt = inw(ndev->base_addr+VLSI_PIO_RCVBCNT) & RCVBCNT_MASK;
if (fifocnt != 0) {
- IRDA_DEBUG(0, "%s: rx fifo not empty(%d)\n", __FUNCTION__, fifocnt);
+ IRDA_DEBUG(0, "%s: rx fifo not empty(%d)\n", __func__, fifocnt);
}
config = inw(iobase+VLSI_PIO_IRCFG);
if (ring_put(r) == NULL) {
netif_stop_queue(ndev);
- IRDA_DEBUG(3, "%s: tx ring full - queue stopped\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s: tx ring full - queue stopped\n", __func__);
}
spin_unlock_irqrestore(&idev->lock, flags);
drop_unlock:
spin_unlock_irqrestore(&idev->lock, flags);
drop:
- IRDA_WARNING("%s: dropping packet - %s\n", __FUNCTION__, msg);
+ IRDA_WARNING("%s: dropping packet - %s\n", __func__, msg);
dev_kfree_skb_any(skb);
idev->stats.tx_errors++;
idev->stats.tx_dropped++;
fifocnt = inw(iobase+VLSI_PIO_RCVBCNT) & RCVBCNT_MASK;
if (fifocnt != 0) {
IRDA_DEBUG(0, "%s: rx fifo not empty(%d)\n",
- __FUNCTION__, fifocnt);
+ __func__, fifocnt);
}
outw(config | IRCFG_ENTX, iobase+VLSI_PIO_IRCFG);
}
if (netif_queue_stopped(ndev) && !idev->new_baud) {
netif_wake_queue(ndev);
- IRDA_DEBUG(3, "%s: queue awoken\n", __FUNCTION__);
+ IRDA_DEBUG(3, "%s: queue awoken\n", __func__);
}
}
dev_kfree_skb_any(rd->skb);
rd->skb = NULL;
}
- IRDA_DEBUG(0, "%s - dropping tx packet\n", __FUNCTION__);
+ IRDA_DEBUG(0, "%s - dropping tx packet\n", __func__);
ret = -VLSI_TX_DROP;
}
else
if (count < 3) {
if (clksrc == 1) { /* explicitly asked for PLL hence bail out */
IRDA_ERROR("%s: no PLL or failed to lock!\n",
- __FUNCTION__);
+ __func__);
clkctl = CLKCTL_CLKSTP;
pci_write_config_byte(pdev, VLSI_PCI_CLKCTL, clkctl);
return -1;
clksrc = 3; /* fallback to 40MHz XCLK (OB800) */
IRDA_DEBUG(0, "%s: PLL not locked, fallback to clksrc=%d\n",
- __FUNCTION__, clksrc);
+ __func__, clksrc);
}
else
clksrc = 1; /* got successful PLL lock */
/* start the clock and clean the registers */
if (vlsi_start_clock(pdev)) {
- IRDA_ERROR("%s: no valid clock source\n", __FUNCTION__);
+ IRDA_ERROR("%s: no valid clock source\n", __func__);
return -1;
}
iobase = ndev->base_addr;
vlsi_irda_dev_t *idev = ndev->priv;
- vlsi_reg_debug(ndev->base_addr, __FUNCTION__);
+ vlsi_reg_debug(ndev->base_addr, __func__);
vlsi_ring_debug(idev->tx_ring);
if (netif_running(ndev))
if (vlsi_start_hw(idev))
IRDA_ERROR("%s: failed to restart hw - %s(%s) unusable!\n",
- __FUNCTION__, pci_name(idev->pdev), ndev->name);
+ __func__, pci_name(idev->pdev), ndev->name);
else
netif_start_queue(ndev);
}
break;
default:
IRDA_WARNING("%s: notsupp - cmd=%04x\n",
- __FUNCTION__, cmd);
+ __func__, cmd);
ret = -EOPNOTSUPP;
}
if (boguscount <= 0)
IRDA_MESSAGE("%s: too much work in interrupt!\n",
- __FUNCTION__);
+ __func__);
return IRQ_RETVAL(handled);
}
char hwname[32];
if (pci_request_regions(idev->pdev, drivername)) {
- IRDA_WARNING("%s: io resource busy\n", __FUNCTION__);
+ IRDA_WARNING("%s: io resource busy\n", __func__);
goto errout;
}
ndev->base_addr = pci_resource_start(idev->pdev,0);
if (request_irq(ndev->irq, vlsi_interrupt, IRQF_SHARED,
drivername, ndev)) {
IRDA_WARNING("%s: couldn't get IRQ: %d\n",
- __FUNCTION__, ndev->irq);
+ __func__, ndev->irq);
goto errout_io;
}
netif_start_queue(ndev);
- IRDA_MESSAGE("%s: device %s operational\n", __FUNCTION__, ndev->name);
+ IRDA_MESSAGE("%s: device %s operational\n", __func__, ndev->name);
return 0;
pci_release_regions(idev->pdev);
- IRDA_MESSAGE("%s: device %s stopped\n", __FUNCTION__, ndev->name);
+ IRDA_MESSAGE("%s: device %s stopped\n", __func__, ndev->name);
return 0;
}
if (pci_set_dma_mask(pdev,DMA_MASK_USED_BY_HW)
|| pci_set_dma_mask(pdev,DMA_MASK_MSTRPAGE)) {
- IRDA_ERROR("%s: aborting due to PCI BM-DMA address limitations\n", __FUNCTION__);
+ IRDA_ERROR("%s: aborting due to PCI BM-DMA address limitations\n", __func__);
return -1;
}
if ( !pci_resource_start(pdev,0)
|| !(pci_resource_flags(pdev,0) & IORESOURCE_IO) ) {
- IRDA_ERROR("%s: bar 0 invalid", __FUNCTION__);
+ IRDA_ERROR("%s: bar 0 invalid", __func__);
goto out_disable;
}
ndev = alloc_irdadev(sizeof(*idev));
if (ndev==NULL) {
IRDA_ERROR("%s: Unable to allocate device memory.\n",
- __FUNCTION__);
+ __func__);
goto out_disable;
}
goto out_freedev;
if (register_netdev(ndev) < 0) {
- IRDA_ERROR("%s: register_netdev failed\n", __FUNCTION__);
+ IRDA_ERROR("%s: register_netdev failed\n", __func__);
goto out_freedev;
}
vlsi_proc_root, VLSI_PROC_FOPS, ndev);
if (!ent) {
IRDA_WARNING("%s: failed to create proc entry\n",
- __FUNCTION__);
+ __func__);
} else {
ent->size = 0;
}
if (!ndev) {
IRDA_ERROR("%s - %s: no netdevice \n",
- __FUNCTION__, pci_name(pdev));
+ __func__, pci_name(pdev));
return 0;
}
idev = ndev->priv;
pdev->current_state = state.event;
}
else
- IRDA_ERROR("%s - %s: invalid suspend request %u -> %u\n", __FUNCTION__, pci_name(pdev), pdev->current_state, state.event);
+ IRDA_ERROR("%s - %s: invalid suspend request %u -> %u\n", __func__, pci_name(pdev), pdev->current_state, state.event);
mutex_unlock(&idev->mtx);
return 0;
}
if (!ndev) {
IRDA_ERROR("%s - %s: no netdevice \n",
- __FUNCTION__, pci_name(pdev));
+ __func__, pci_name(pdev));
return 0;
}
idev = ndev->priv;
if (pdev->current_state == 0) {
mutex_unlock(&idev->mtx);
IRDA_WARNING("%s - %s: already resumed\n",
- __FUNCTION__, pci_name(pdev));
+ __func__, pci_name(pdev));
return 0;
}
* now we explicitly set pdev->current_state = 0 after enabling the
* device and independently resume_ok should catch any garbage config.
*/
- IRDA_WARNING("%s - hm, nothing to resume?\n", __FUNCTION__);
+ IRDA_WARNING("%s - hm, nothing to resume?\n", __func__);
mutex_unlock(&idev->mtx);
return 0;
}
*/
if ((a & ~DMA_MASK_MSTRPAGE)>>24 != MSTRPAGE_VALUE) {
- IRDA_ERROR("%s: pci busaddr inconsistency!\n", __FUNCTION__);
+ IRDA_ERROR("%s: pci busaddr inconsistency!\n", __func__);
dump_stack();
return;
}
{
int i;
- IRDA_DEBUG(0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s()\n", __func__ );
for (i=0; (io[i] < 2000) && (i < ARRAY_SIZE(dev_self)); i++) {
if (w83977af_open(i, io[i], irq[i], dma[i]) == 0)
{
int i;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s()\n", __func__ );
for (i=0; i < ARRAY_SIZE(dev_self); i++) {
if (dev_self[i])
struct w83977af_ir *self;
int err;
- IRDA_DEBUG(0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s()\n", __func__ );
/* Lock the port that we need */
if (!request_region(iobase, CHIP_IO_EXTENT, driver_name)) {
IRDA_DEBUG(0, "%s(), can't get iobase of 0x%03x\n",
- __FUNCTION__ , iobase);
+ __func__ , iobase);
return -ENODEV;
}
err = register_netdev(dev);
if (err) {
- IRDA_ERROR("%s(), register_netdevice() failed!\n", __FUNCTION__);
+ IRDA_ERROR("%s(), register_netdevice() failed!\n", __func__);
goto err_out3;
}
IRDA_MESSAGE("IrDA: Registered device %s\n", dev->name);
{
int iobase;
- IRDA_DEBUG(0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s()\n", __func__ );
iobase = self->io.fir_base;
/* Release the PORT that this driver is using */
IRDA_DEBUG(0 , "%s(), Releasing Region %03x\n",
- __FUNCTION__ , self->io.fir_base);
+ __func__ , self->io.fir_base);
release_region(self->io.fir_base, self->io.fir_ext);
if (self->tx_buff.head)
int i;
for (i=0; i < 2; i++) {
- IRDA_DEBUG( 0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG( 0, "%s()\n", __func__ );
#ifdef CONFIG_USE_W977_PNP
/* Enter PnP configuration mode */
w977_efm_enter(efbase[i]);
return 0;
} else {
/* Try next extented function register address */
- IRDA_DEBUG( 0, "%s(), Wrong chip version", __FUNCTION__ );
+ IRDA_DEBUG( 0, "%s(), Wrong chip version", __func__ );
}
}
return -1;
case 115200: outb(0x01, iobase+ABLL); break;
case 576000:
ir_mode = HCR_MIR_576;
- IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), handling baud of 576000\n", __func__ );
break;
case 1152000:
ir_mode = HCR_MIR_1152;
- IRDA_DEBUG(0, "%s(), handling baud of 1152000\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), handling baud of 1152000\n", __func__ );
break;
case 4000000:
ir_mode = HCR_FIR;
- IRDA_DEBUG(0, "%s(), handling baud of 4000000\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), handling baud of 4000000\n", __func__ );
break;
default:
ir_mode = HCR_FIR;
- IRDA_DEBUG(0, "%s(), unknown baud rate of %d\n", __FUNCTION__ , speed);
+ IRDA_DEBUG(0, "%s(), unknown baud rate of %d\n", __func__ , speed);
break;
}
iobase = self->io.fir_base;
- IRDA_DEBUG(4, "%s(%ld), skb->len=%d\n", __FUNCTION__ , jiffies,
+ IRDA_DEBUG(4, "%s(%ld), skb->len=%d\n", __func__ , jiffies,
(int) skb->len);
/* Lock transmit buffer */
outb(ICR_ETMRI, iobase+ICR);
} else {
#endif
- IRDA_DEBUG(4, "%s(%ld), mtt=%d\n", __FUNCTION__ , jiffies, mtt);
+ IRDA_DEBUG(4, "%s(%ld), mtt=%d\n", __func__ , jiffies, mtt);
if (mtt)
udelay(mtt);
unsigned long flags;
__u8 hcr;
#endif
- IRDA_DEBUG(4, "%s(), len=%d\n", __FUNCTION__ , self->tx_buff.len);
+ IRDA_DEBUG(4, "%s(), len=%d\n", __func__ , self->tx_buff.len);
/* Save current set */
set = inb(iobase+SSR);
int actual = 0;
__u8 set;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s()\n", __func__ );
/* Save current bank */
set = inb(iobase+SSR);
switch_bank(iobase, SET0);
if (!(inb_p(iobase+USR) & USR_TSRE)) {
IRDA_DEBUG(4,
- "%s(), warning, FIFO not empty yet!\n", __FUNCTION__ );
+ "%s(), warning, FIFO not empty yet!\n", __func__ );
fifo_size -= 17;
IRDA_DEBUG(4, "%s(), %d bytes left in tx fifo\n",
- __FUNCTION__ , fifo_size);
+ __func__ , fifo_size);
}
/* Fill FIFO with current frame */
}
IRDA_DEBUG(4, "%s(), fifo_size %d ; %d sent of %d\n",
- __FUNCTION__ , fifo_size, actual, len);
+ __func__ , fifo_size, actual, len);
/* Restore bank */
outb(set, iobase+SSR);
int iobase;
__u8 set;
- IRDA_DEBUG(4, "%s(%ld)\n", __FUNCTION__ , jiffies);
+ IRDA_DEBUG(4, "%s(%ld)\n", __func__ , jiffies);
IRDA_ASSERT(self != NULL, return;);
/* Check for underrrun! */
if (inb(iobase+AUDR) & AUDR_UNDR) {
- IRDA_DEBUG(0, "%s(), Transmit underrun!\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s(), Transmit underrun!\n", __func__ );
self->stats.tx_errors++;
self->stats.tx_fifo_errors++;
#endif
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(4, "%s\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s\n", __func__ );
iobase= self->io.fir_base;
__u8 set;
__u8 status;
- IRDA_DEBUG(4, "%s\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s\n", __func__ );
st_fifo = &self->st_fifo;
skb = dev_alloc_skb(len+1);
if (skb == NULL) {
printk(KERN_INFO
- "%s(), memory squeeze, dropping frame.\n", __FUNCTION__);
+ "%s(), memory squeeze, dropping frame.\n", __func__);
/* Restore set register */
outb(set, iobase+SSR);
__u8 byte = 0x00;
int iobase;
- IRDA_DEBUG(4, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(4, "%s()\n", __func__ );
IRDA_ASSERT(self != NULL, return;);
__u8 set;
int iobase;
- IRDA_DEBUG(4, "%s(), isr=%#x\n", __FUNCTION__ , isr);
+ IRDA_DEBUG(4, "%s(), isr=%#x\n", __func__ , isr);
iobase = self->io.fir_base;
/* Transmit FIFO low on data */
/* Check if we need to change the speed? */
if (self->new_speed) {
IRDA_DEBUG(2,
- "%s(), Changing speed!\n", __FUNCTION__ );
+ "%s(), Changing speed!\n", __func__ );
w83977af_change_speed(self, self->new_speed);
self->new_speed = 0;
}
char hwname[32];
__u8 set;
- IRDA_DEBUG(0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s()\n", __func__ );
IRDA_ASSERT(dev != NULL, return -1;);
self = (struct w83977af_ir *) dev->priv;
int iobase;
__u8 set;
- IRDA_DEBUG(0, "%s()\n", __FUNCTION__ );
+ IRDA_DEBUG(0, "%s()\n", __func__ );
IRDA_ASSERT(dev != NULL, return -1;);
IRDA_ASSERT(self != NULL, return -1;);
- IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __FUNCTION__ , dev->name, cmd);
+ IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__ , dev->name, cmd);
spin_lock_irqsave(&self->lock, flags);
#include <linux/kernel.h>
#include <linux/init.h>
-#include <asm/hardware.h>
-#include <asm/arch/ixp2000-regs.h>
+#include <mach/hardware.h>
+#include <mach/ixp2000-regs.h>
#include <asm/delay.h>
#include <asm/io.h>
#include "ixp2400-msf.h"
#include <linux/init.h>
#include <linux/moduleparam.h>
#include <asm/hardware/uengine.h>
-#include <asm/mach-types.h>
#include <asm/io.h>
#include "ixp2400_rx.ucode"
#include "ixp2400_tx.ucode"
return;
}
if (dev->mc_count == 0 && !(dev->flags & (IFF_PROMISC | IFF_ALLMULTI))) {
- if (dev->flags & IFF_ALLMULTI)
- dev->flags |= IFF_PROMISC;
lp->i596_config[8] &= ~0x01;
} else {
lp->i596_config[8] |= 0x01;
#include <linux/platform_device.h>
#include <linux/phy.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
#include "macb.h"
DPRINTK("Loading MAC Address: %s\n", print_mac(mac, dev->dev_addr));
macaddr = 0;
for (i = 0; i < 6; i++)
- macaddr |= dev->dev_addr[i] << ((5 - i) * 8);
+ macaddr |= (u64)dev->dev_addr[i] << ((5 - i) * 8);
mace->eth.mac_addr = macaddr;
}
#include <asm/system.h>
static char mv643xx_eth_driver_name[] = "mv643xx_eth";
-static char mv643xx_eth_driver_version[] = "1.1";
+static char mv643xx_eth_driver_version[] = "1.2";
#define MV643XX_ETH_CHECKSUM_OFFLOAD_TX
#define MV643XX_ETH_NAPI
#define PORT_SERIAL_CONTROL(p) (0x043c + ((p) << 10))
#define PORT_STATUS(p) (0x0444 + ((p) << 10))
#define TX_FIFO_EMPTY 0x00000400
+#define TX_IN_PROGRESS 0x00000080
+#define PORT_SPEED_MASK 0x00000030
+#define PORT_SPEED_1000 0x00000010
+#define PORT_SPEED_100 0x00000020
+#define PORT_SPEED_10 0x00000000
+#define FLOW_CONTROL_ENABLED 0x00000008
+#define FULL_DUPLEX 0x00000004
+#define LINK_UP 0x00000002
#define TXQ_COMMAND(p) (0x0448 + ((p) << 10))
#define TXQ_FIX_PRIO_CONF(p) (0x044c + ((p) << 10))
#define TX_BW_RATE(p) (0x0450 + ((p) << 10))
#define TX_BW_MTU(p) (0x0458 + ((p) << 10))
#define TX_BW_BURST(p) (0x045c + ((p) << 10))
#define INT_CAUSE(p) (0x0460 + ((p) << 10))
+#define INT_TX_END_0 0x00080000
#define INT_TX_END 0x07f80000
#define INT_RX 0x0007fbfc
#define INT_EXT 0x00000002
/*
* SDMA configuration register.
*/
-#define RX_BURST_SIZE_4_64BIT (2 << 1)
+#define RX_BURST_SIZE_16_64BIT (4 << 1)
#define BLM_RX_NO_SWAP (1 << 4)
#define BLM_TX_NO_SWAP (1 << 5)
-#define TX_BURST_SIZE_4_64BIT (2 << 22)
+#define TX_BURST_SIZE_16_64BIT (4 << 22)
#if defined(__BIG_ENDIAN)
#define PORT_SDMA_CONFIG_DEFAULT_VALUE \
- RX_BURST_SIZE_4_64BIT | \
- TX_BURST_SIZE_4_64BIT
+ RX_BURST_SIZE_16_64BIT | \
+ TX_BURST_SIZE_16_64BIT
#elif defined(__LITTLE_ENDIAN)
#define PORT_SDMA_CONFIG_DEFAULT_VALUE \
- RX_BURST_SIZE_4_64BIT | \
+ RX_BURST_SIZE_16_64BIT | \
BLM_RX_NO_SWAP | \
BLM_TX_NO_SWAP | \
- TX_BURST_SIZE_4_64BIT
+ TX_BURST_SIZE_16_64BIT
#else
#error One of __BIG_ENDIAN or __LITTLE_ENDIAN must be defined
#endif
#define SET_MII_SPEED_TO_100 (1 << 24)
#define SET_GMII_SPEED_TO_1000 (1 << 23)
#define SET_FULL_DUPLEX_MODE (1 << 21)
-#define MAX_RX_PACKET_1522BYTE (1 << 17)
#define MAX_RX_PACKET_9700BYTE (5 << 17)
-#define MAX_RX_PACKET_MASK (7 << 17)
#define DISABLE_AUTO_NEG_SPEED_GMII (1 << 13)
#define DO_NOT_FORCE_LINK_FAIL (1 << 10)
#define SERIAL_PORT_CONTROL_RESERVED (1 << 9)
#define GEN_IP_V4_CHECKSUM 0x00040000
#define GEN_TCP_UDP_CHECKSUM 0x00020000
#define UDP_FRAME 0x00010000
+#define MAC_HDR_EXTRA_4_BYTES 0x00008000
+#define MAC_HDR_EXTRA_8_BYTES 0x00000200
#define TX_IHL_SHIFT 11
udelay(10);
}
+static void txq_reset_hw_ptr(struct tx_queue *txq)
+{
+ struct mv643xx_eth_private *mp = txq_to_mp(txq);
+ int off = TXQ_CURRENT_DESC_PTR(mp->port_num, txq->index);
+ u32 addr;
+
+ addr = (u32)txq->tx_desc_dma;
+ addr += txq->tx_curr_desc * sizeof(struct tx_desc);
+ wrl(mp, off, addr);
+}
+
static void txq_enable(struct tx_queue *txq)
{
struct mv643xx_eth_private *mp = txq_to_mp(txq);
for (i = 0; i < 8; i++)
if (mp->txq_mask & (1 << i))
txq_reclaim(mp->txq + i, 0);
+
+ if (netif_carrier_ok(mp->dev)) {
+ spin_lock(&mp->lock);
+ __txq_maybe_wake(mp->txq + mp->txq_primary);
+ spin_unlock(&mp->lock);
+ }
}
#endif
static void txq_submit_skb(struct tx_queue *txq, struct sk_buff *skb)
{
+ struct mv643xx_eth_private *mp = txq_to_mp(txq);
int nr_frags = skb_shinfo(skb)->nr_frags;
int tx_index;
struct tx_desc *desc;
desc->buf_ptr = dma_map_single(NULL, skb->data, length, DMA_TO_DEVICE);
if (skb->ip_summed == CHECKSUM_PARTIAL) {
- BUG_ON(skb->protocol != htons(ETH_P_IP));
+ int mac_hdr_len;
+
+ BUG_ON(skb->protocol != htons(ETH_P_IP) &&
+ skb->protocol != htons(ETH_P_8021Q));
cmd_sts |= GEN_TCP_UDP_CHECKSUM |
GEN_IP_V4_CHECKSUM |
ip_hdr(skb)->ihl << TX_IHL_SHIFT;
+ mac_hdr_len = (void *)ip_hdr(skb) - (void *)skb->data;
+ switch (mac_hdr_len - ETH_HLEN) {
+ case 0:
+ break;
+ case 4:
+ cmd_sts |= MAC_HDR_EXTRA_4_BYTES;
+ break;
+ case 8:
+ cmd_sts |= MAC_HDR_EXTRA_8_BYTES;
+ break;
+ case 12:
+ cmd_sts |= MAC_HDR_EXTRA_4_BYTES;
+ cmd_sts |= MAC_HDR_EXTRA_8_BYTES;
+ break;
+ default:
+ if (net_ratelimit())
+ dev_printk(KERN_ERR, &txq_to_mp(txq)->dev->dev,
+ "mac header length is %d?!\n", mac_hdr_len);
+ break;
+ }
+
switch (ip_hdr(skb)->protocol) {
case IPPROTO_UDP:
cmd_sts |= UDP_FRAME;
wmb();
desc->cmd_sts = cmd_sts;
+ /* clear TX_END interrupt status */
+ wrl(mp, INT_CAUSE(mp->port_num), ~(INT_TX_END_0 << txq->index));
+ rdl(mp, INT_CAUSE(mp->port_num));
+
/* ensure all descriptors are written before poking hardware */
wmb();
txq_enable(txq);
static int mv643xx_eth_get_settings_phyless(struct net_device *dev, struct ethtool_cmd *cmd)
{
+ struct mv643xx_eth_private *mp = netdev_priv(dev);
+ u32 port_status;
+
+ port_status = rdl(mp, PORT_STATUS(mp->port_num));
+
cmd->supported = SUPPORTED_MII;
cmd->advertising = ADVERTISED_MII;
- cmd->speed = SPEED_1000;
- cmd->duplex = DUPLEX_FULL;
+ switch (port_status & PORT_SPEED_MASK) {
+ case PORT_SPEED_10:
+ cmd->speed = SPEED_10;
+ break;
+ case PORT_SPEED_100:
+ cmd->speed = SPEED_100;
+ break;
+ case PORT_SPEED_1000:
+ cmd->speed = SPEED_1000;
+ break;
+ default:
+ cmd->speed = -1;
+ break;
+ }
+ cmd->duplex = (port_status & FULL_DUPLEX) ? DUPLEX_FULL : DUPLEX_HALF;
cmd->port = PORT_MII;
cmd->phy_address = 0;
cmd->transceiver = XCVR_INTERNAL;
tx_desc = (struct tx_desc *)txq->tx_desc_area;
for (i = 0; i < txq->tx_ring_size; i++) {
+ struct tx_desc *txd = tx_desc + i;
int nexti = (i + 1) % txq->tx_ring_size;
- tx_desc[i].next_desc_ptr = txq->tx_desc_dma +
+
+ txd->cmd_sts = 0;
+ txd->next_desc_ptr = txq->tx_desc_dma +
nexti * sizeof(struct tx_desc);
}
desc = &txq->tx_desc_area[tx_index];
cmd_sts = desc->cmd_sts;
- if (!force && (cmd_sts & BUFFER_OWNED_BY_DMA))
- break;
+ if (cmd_sts & BUFFER_OWNED_BY_DMA) {
+ if (!force)
+ break;
+ desc->cmd_sts = cmd_sts & ~BUFFER_OWNED_BY_DMA;
+ }
txq->tx_used_desc = (tx_index + 1) % txq->tx_ring_size;
txq->tx_desc_count--;
/* netdev ops and related ***************************************************/
-static void update_pscr(struct mv643xx_eth_private *mp, int speed, int duplex)
+static void handle_link_event(struct mv643xx_eth_private *mp)
{
- u32 pscr_o;
- u32 pscr_n;
-
- pscr_o = rdl(mp, PORT_SERIAL_CONTROL(mp->port_num));
+ struct net_device *dev = mp->dev;
+ u32 port_status;
+ int speed;
+ int duplex;
+ int fc;
+
+ port_status = rdl(mp, PORT_STATUS(mp->port_num));
+ if (!(port_status & LINK_UP)) {
+ if (netif_carrier_ok(dev)) {
+ int i;
- /* clear speed, duplex and rx buffer size fields */
- pscr_n = pscr_o & ~(SET_MII_SPEED_TO_100 |
- SET_GMII_SPEED_TO_1000 |
- SET_FULL_DUPLEX_MODE |
- MAX_RX_PACKET_MASK);
+ printk(KERN_INFO "%s: link down\n", dev->name);
- if (speed == SPEED_1000) {
- pscr_n |= SET_GMII_SPEED_TO_1000 | MAX_RX_PACKET_9700BYTE;
- } else {
- if (speed == SPEED_100)
- pscr_n |= SET_MII_SPEED_TO_100;
- pscr_n |= MAX_RX_PACKET_1522BYTE;
- }
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
- if (duplex == DUPLEX_FULL)
- pscr_n |= SET_FULL_DUPLEX_MODE;
+ for (i = 0; i < 8; i++) {
+ struct tx_queue *txq = mp->txq + i;
- if (pscr_n != pscr_o) {
- if ((pscr_o & SERIAL_PORT_ENABLE) == 0)
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr_n);
- else {
- int i;
+ if (mp->txq_mask & (1 << i)) {
+ txq_reclaim(txq, 1);
+ txq_reset_hw_ptr(txq);
+ }
+ }
+ }
+ return;
+ }
- for (i = 0; i < 8; i++)
- if (mp->txq_mask & (1 << i))
- txq_disable(mp->txq + i);
+ switch (port_status & PORT_SPEED_MASK) {
+ case PORT_SPEED_10:
+ speed = 10;
+ break;
+ case PORT_SPEED_100:
+ speed = 100;
+ break;
+ case PORT_SPEED_1000:
+ speed = 1000;
+ break;
+ default:
+ speed = -1;
+ break;
+ }
+ duplex = (port_status & FULL_DUPLEX) ? 1 : 0;
+ fc = (port_status & FLOW_CONTROL_ENABLED) ? 1 : 0;
- pscr_o &= ~SERIAL_PORT_ENABLE;
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr_o);
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr_n);
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr_n);
+ printk(KERN_INFO "%s: link up, %d Mb/s, %s duplex, "
+ "flow control %sabled\n", dev->name,
+ speed, duplex ? "full" : "half",
+ fc ? "en" : "dis");
- for (i = 0; i < 8; i++)
- if (mp->txq_mask & (1 << i))
- txq_enable(mp->txq + i);
- }
+ if (!netif_carrier_ok(dev)) {
+ netif_carrier_on(dev);
+ netif_wake_queue(dev);
}
}
struct mv643xx_eth_private *mp = netdev_priv(dev);
u32 int_cause;
u32 int_cause_ext;
- u32 txq_active;
int_cause = rdl(mp, INT_CAUSE(mp->port_num)) &
(INT_TX_END | INT_RX | INT_EXT);
wrl(mp, INT_CAUSE_EXT(mp->port_num), ~int_cause_ext);
}
- if (int_cause_ext & (INT_EXT_PHY | INT_EXT_LINK)) {
- if (mp->phy_addr == -1 || mii_link_ok(&mp->mii)) {
- int i;
-
- if (mp->phy_addr != -1) {
- struct ethtool_cmd cmd;
-
- mii_ethtool_gset(&mp->mii, &cmd);
- update_pscr(mp, cmd.speed, cmd.duplex);
- }
-
- for (i = 0; i < 8; i++)
- if (mp->txq_mask & (1 << i))
- txq_enable(mp->txq + i);
-
- if (!netif_carrier_ok(dev)) {
- netif_carrier_on(dev);
- __txq_maybe_wake(mp->txq + mp->txq_primary);
- }
- } else if (netif_carrier_ok(dev)) {
- netif_stop_queue(dev);
- netif_carrier_off(dev);
- }
- }
+ if (int_cause_ext & (INT_EXT_PHY | INT_EXT_LINK))
+ handle_link_event(mp);
/*
* RxBuffer or RxError set for any of the 8 queues?
}
#endif
- txq_active = rdl(mp, TXQ_COMMAND(mp->port_num));
-
/*
* TxBuffer or TxError set for any of the 8 queues?
*/
for (i = 0; i < 8; i++)
if (mp->txq_mask & (1 << i))
txq_reclaim(mp->txq + i, 0);
+
+ /*
+ * Enough space again in the primary TX queue for a
+ * full packet?
+ */
+ if (netif_carrier_ok(dev)) {
+ spin_lock(&mp->lock);
+ __txq_maybe_wake(mp->txq + mp->txq_primary);
+ spin_unlock(&mp->lock);
+ }
}
/*
int i;
wrl(mp, INT_CAUSE(mp->port_num), ~(int_cause & INT_TX_END));
+
+ spin_lock(&mp->lock);
for (i = 0; i < 8; i++) {
struct tx_queue *txq = mp->txq + i;
- if (txq->tx_desc_count && !((txq_active >> i) & 1))
+ u32 hw_desc_ptr;
+ u32 expected_ptr;
+
+ if ((int_cause & (INT_TX_END_0 << i)) == 0)
+ continue;
+
+ hw_desc_ptr =
+ rdl(mp, TXQ_CURRENT_DESC_PTR(mp->port_num, i));
+ expected_ptr = (u32)txq->tx_desc_dma +
+ txq->tx_curr_desc * sizeof(struct tx_desc);
+
+ if (hw_desc_ptr != expected_ptr)
txq_enable(txq);
}
- }
-
- /*
- * Enough space again in the primary TX queue for a full packet?
- */
- if (int_cause_ext & INT_EXT_TX) {
- struct tx_queue *txq = mp->txq + mp->txq_primary;
- __txq_maybe_wake(txq);
+ spin_unlock(&mp->lock);
}
return IRQ_HANDLED;
{
unsigned int data;
- smi_reg_read(mp, mp->phy_addr, 0, &data);
- data |= 0x8000;
- smi_reg_write(mp, mp->phy_addr, 0, data);
+ smi_reg_read(mp, mp->phy_addr, MII_BMCR, &data);
+ data |= BMCR_RESET;
+ smi_reg_write(mp, mp->phy_addr, MII_BMCR, data);
do {
udelay(1);
- smi_reg_read(mp, mp->phy_addr, 0, &data);
- } while (data & 0x8000);
+ smi_reg_read(mp, mp->phy_addr, MII_BMCR, &data);
+ } while (data & BMCR_RESET);
}
static void port_start(struct mv643xx_eth_private *mp)
u32 pscr;
int i;
- /*
- * Configure basic link parameters.
- */
- pscr = rdl(mp, PORT_SERIAL_CONTROL(mp->port_num));
- pscr &= ~(SERIAL_PORT_ENABLE | FORCE_LINK_PASS);
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
- pscr |= DISABLE_AUTO_NEG_FOR_FLOW_CTRL |
- DISABLE_AUTO_NEG_SPEED_GMII |
- DISABLE_AUTO_NEG_FOR_DUPLEX |
- DO_NOT_FORCE_LINK_FAIL |
- SERIAL_PORT_CONTROL_RESERVED;
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
- pscr |= SERIAL_PORT_ENABLE;
- wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
-
- wrl(mp, SDMA_CONFIG(mp->port_num), PORT_SDMA_CONFIG_DEFAULT_VALUE);
-
/*
* Perform PHY reset, if there is a PHY.
*/
mv643xx_eth_set_settings(mp->dev, &cmd);
}
+ /*
+ * Configure basic link parameters.
+ */
+ pscr = rdl(mp, PORT_SERIAL_CONTROL(mp->port_num));
+
+ pscr |= SERIAL_PORT_ENABLE;
+ wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
+
+ pscr |= DO_NOT_FORCE_LINK_FAIL;
+ if (mp->phy_addr == -1)
+ pscr |= FORCE_LINK_PASS;
+ wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
+
+ wrl(mp, SDMA_CONFIG(mp->port_num), PORT_SDMA_CONFIG_DEFAULT_VALUE);
+
/*
* Configure TX path and queues.
*/
tx_set_rate(mp, 1000000000, 16777216);
for (i = 0; i < 8; i++) {
struct tx_queue *txq = mp->txq + i;
- int off = TXQ_CURRENT_DESC_PTR(mp->port_num, i);
- u32 addr;
if ((mp->txq_mask & (1 << i)) == 0)
continue;
- addr = (u32)txq->tx_desc_dma;
- addr += txq->tx_curr_desc * sizeof(struct tx_desc);
- wrl(mp, off, addr);
-
+ txq_reset_hw_ptr(txq);
txq_set_rate(txq, 1000000000, 16777216);
txq_set_fixed_prio_mode(txq);
}
napi_enable(&mp->napi);
#endif
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+
port_start(mp);
set_rx_coal(mp, 0);
if (mp->txq_mask & (1 << i))
txq_disable(mp->txq + i);
}
- while (!(rdl(mp, PORT_STATUS(mp->port_num)) & TX_FIFO_EMPTY))
+
+ while (1) {
+ u32 ps = rdl(mp, PORT_STATUS(mp->port_num));
+
+ if ((ps & (TX_IN_PROGRESS | TX_FIFO_EMPTY)) == TX_FIFO_EMPTY)
+ break;
udelay(10);
+ }
/* Reset the Enable bit in the Configuration Register */
data = rdl(mp, PORT_SERIAL_CONTROL(mp->port_num));
int ret;
if (!mv643xx_eth_version_printed++)
- printk(KERN_NOTICE "MV-643xx 10/100/1000 Ethernet Driver\n");
+ printk(KERN_NOTICE "MV-643xx 10/100/1000 ethernet "
+ "driver version %s\n", mv643xx_eth_driver_version);
ret = -EINVAL;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
unsigned int data;
unsigned int data2;
- smi_reg_read(mp, mp->phy_addr, 0, &data);
- smi_reg_write(mp, mp->phy_addr, 0, data ^ 0x1000);
+ smi_reg_read(mp, mp->phy_addr, MII_BMCR, &data);
+ smi_reg_write(mp, mp->phy_addr, MII_BMCR, data ^ BMCR_ANENABLE);
- smi_reg_read(mp, mp->phy_addr, 0, &data2);
- if (((data ^ data2) & 0x1000) == 0)
+ smi_reg_read(mp, mp->phy_addr, MII_BMCR, &data2);
+ if (((data ^ data2) & BMCR_ANENABLE) == 0)
return -ENODEV;
- smi_reg_write(mp, mp->phy_addr, 0, data);
+ smi_reg_write(mp, mp->phy_addr, MII_BMCR, data);
return 0;
}
cmd.duplex = pd->duplex;
}
- update_pscr(mp, cmd.speed, cmd.duplex);
mv643xx_eth_set_settings(mp->dev, &cmd);
return 0;
}
+static void init_pscr(struct mv643xx_eth_private *mp, int speed, int duplex)
+{
+ u32 pscr;
+
+ pscr = rdl(mp, PORT_SERIAL_CONTROL(mp->port_num));
+ if (pscr & SERIAL_PORT_ENABLE) {
+ pscr &= ~SERIAL_PORT_ENABLE;
+ wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
+ }
+
+ pscr = MAX_RX_PACKET_9700BYTE | SERIAL_PORT_CONTROL_RESERVED;
+ if (mp->phy_addr == -1) {
+ pscr |= DISABLE_AUTO_NEG_SPEED_GMII;
+ if (speed == SPEED_1000)
+ pscr |= SET_GMII_SPEED_TO_1000;
+ else if (speed == SPEED_100)
+ pscr |= SET_MII_SPEED_TO_100;
+
+ pscr |= DISABLE_AUTO_NEG_FOR_FLOW_CTRL;
+
+ pscr |= DISABLE_AUTO_NEG_FOR_DUPLEX;
+ if (duplex == DUPLEX_FULL)
+ pscr |= SET_FULL_DUPLEX_MODE;
+ }
+
+ wrl(mp, PORT_SERIAL_CONTROL(mp->port_num), pscr);
+}
+
static int mv643xx_eth_probe(struct platform_device *pdev)
{
struct mv643xx_eth_platform_data *pd;
} else {
SET_ETHTOOL_OPS(dev, &mv643xx_eth_ethtool_ops_phyless);
}
+ init_pscr(mp, pd->speed, pd->duplex);
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
* have to map the buffers to ISA memory which is only 16 MB
*/
dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
+ dev->vlan_features = NETIF_F_SG | NETIF_F_IP_CSUM;
#endif
SET_NETDEV_DEV(dev, &pdev->dev);
dev_err(&pdev->dev, "Error %d setting DMA mask\n", status);
goto abort_with_netdev;
}
+ (void)pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
mgp->cmd = dma_alloc_coherent(&pdev->dev, sizeof(*mgp->cmd),
&mgp->cmd_bus, GFP_KERNEL);
if (mgp->cmd == NULL)
#define MXGEFW_ETH_SEND_3 0x2c0000
#define MXGEFW_ETH_RECV_SMALL 0x300000
#define MXGEFW_ETH_RECV_BIG 0x340000
+#define MXGEFW_ETH_SEND_GO 0x380000
+#define MXGEFW_ETH_SEND_STOP 0x3C0000
#define MXGEFW_ETH_SEND(n) (0x200000 + (((n) & 0x03) * 0x40000))
#define MXGEFW_ETH_SEND_OFFSET(n) (MXGEFW_ETH_SEND(n) - MXGEFW_ETH_SEND_4)
* MXGEFW_CMD_RESET is issued */
MXGEFW_CMD_SET_INTRQ_DMA,
+ /* data0 = LSW of the host address
+ * data1 = MSW of the host address
+ * data2 = slice number if multiple slices are used
+ */
+
MXGEFW_CMD_SET_BIG_BUFFER_SIZE, /* in bytes, power of 2 */
MXGEFW_CMD_SET_SMALL_BUFFER_SIZE, /* in bytes */
MXGEFW_CMD_GET_SEND_OFFSET,
MXGEFW_CMD_GET_SMALL_RX_OFFSET,
MXGEFW_CMD_GET_BIG_RX_OFFSET,
+ /* data0 = slice number if multiple slices are used */
+
MXGEFW_CMD_GET_IRQ_ACK_OFFSET,
MXGEFW_CMD_GET_IRQ_DEASSERT_OFFSET,
MXGEFW_CMD_SET_STATS_DMA_V2,
/* data0, data1 = bus addr,
* data2 = sizeof(struct mcp_irq_data) from driver point of view, allows
- * adding new stuff to mcp_irq_data without changing the ABI */
+ * adding new stuff to mcp_irq_data without changing the ABI
+ *
+ * If multiple slices are used, data2 contains both the size of the
+ * structure (in the lower 16 bits) and the slice number
+ * (in the upper 16 bits).
+ */
MXGEFW_CMD_UNALIGNED_TEST,
/* same than DMA_TEST (same args) but abort with UNALIGNED on unaligned
MXGEFW_CMD_GET_MAX_RSS_QUEUES,
MXGEFW_CMD_ENABLE_RSS_QUEUES,
/* data0 = number of slices n (0, 1, ..., n-1) to enable
- * data1 = interrupt mode.
- * 0=share one INTx/MSI, 1=use one MSI-X per queue.
+ * data1 = interrupt mode | use of multiple transmit queues.
+ * 0=share one INTx/MSI.
+ * 1=use one MSI-X per queue.
* If all queues share one interrupt, the driver must have set
* RSS_SHARED_INTERRUPT_DMA before enabling queues.
+ * 2=enable both receive and send queues.
+ * Without this bit set, only one send queue (slice 0's send queue)
+ * is enabled. The receive queues are always enabled.
*/
-#define MXGEFW_SLICE_INTR_MODE_SHARED 0
-#define MXGEFW_SLICE_INTR_MODE_ONE_PER_SLICE 1
+#define MXGEFW_SLICE_INTR_MODE_SHARED 0x0
+#define MXGEFW_SLICE_INTR_MODE_ONE_PER_SLICE 0x1
+#define MXGEFW_SLICE_ENABLE_MULTIPLE_TX_QUEUES 0x2
MXGEFW_CMD_GET_RSS_SHARED_INTERRUPT_MASK_OFFSET,
MXGEFW_CMD_SET_RSS_SHARED_INTERRUPT_DMA,
* 2: TCP_IPV4 (required by RSS)
* 3: IPV4 | TCP_IPV4 (required by RSS)
* 4: source port
+ * 5: source port + destination port
*/
#define MXGEFW_RSS_HASH_TYPE_IPV4 0x1
#define MXGEFW_RSS_HASH_TYPE_TCP_IPV4 0x2
#define MXGEFW_RSS_HASH_TYPE_SRC_PORT 0x4
+#define MXGEFW_RSS_HASH_TYPE_SRC_DST_PORT 0x5
+#define MXGEFW_RSS_HASH_TYPE_MAX 0x5
MXGEFW_CMD_GET_MAX_TSO6_HDR_SIZE,
/* Return data = the max. size of the entire headers of a IPv6 TSO packet.
MXGEFW_CMD_GET_DCA_OFFSET,
/* offset of dca control for WDMAs */
+
+ /* VMWare NetQueue commands */
+ MXGEFW_CMD_NETQ_GET_FILTERS_PER_QUEUE,
+ MXGEFW_CMD_NETQ_ADD_FILTER,
+ /* data0 = filter_id << 16 | queue << 8 | type */
+ /* data1 = MS4 of MAC Addr */
+ /* data2 = LS2_MAC << 16 | VLAN_tag */
+ MXGEFW_CMD_NETQ_DEL_FILTER,
+ /* data0 = filter_id */
+ MXGEFW_CMD_NETQ_QUERY1,
+ MXGEFW_CMD_NETQ_QUERY2,
+ MXGEFW_CMD_NETQ_QUERY3,
+ MXGEFW_CMD_NETQ_QUERY4,
+
};
enum myri10ge_mcp_cmd_status {
u8 valid;
};
+/* definitions for NETQ filter type */
+#define MXGEFW_NETQ_FILTERTYPE_NONE 0
+#define MXGEFW_NETQ_FILTERTYPE_MACADDR 1
+#define MXGEFW_NETQ_FILTERTYPE_VLAN 2
+#define MXGEFW_NETQ_FILTERTYPE_VLANMACADDR 3
+
#endif /* __MYRI10GE_MCP_H__ */
unsigned char mcp_index;
unsigned char disable_rabbit;
unsigned char unaligned_tlp;
- unsigned char pad1;
+ unsigned char pcie_link_algo;
unsigned counters_addr;
unsigned copy_block_info; /* for small mcps loaded with "lload -d" */
unsigned short handoff_id_major; /* must be equal */
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = eip_poll;
#endif
- NS8390_init(dev, 0);
+ NS8390p_init(dev, 0);
ret = register_netdev(dev);
if (ret)
if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */
printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
ne_reset_8390(dev);
- NS8390_init(dev,1);
+ NS8390p_init(dev, 1);
break;
}
if (netif_running(dev)) {
ne_reset_8390(dev);
- NS8390_init(dev, 1);
+ NS8390p_init(dev, 1);
netif_device_attach(dev);
}
return 0;
static char config[MAX_PARAM_LENGTH];
module_param_string(netconsole, config, MAX_PARAM_LENGTH, 0);
-MODULE_PARM_DESC(netconsole, " netconsole=[src-port]@[src-ip]/[dev],[tgt-port]@<tgt-ip>/[tgt-macaddr]\n");
+MODULE_PARM_DESC(netconsole, " netconsole=[src-port]@[src-ip]/[dev],[tgt-port]@<tgt-ip>/[tgt-macaddr]");
#ifndef MODULE
static int __init option_setup(char *opt)
#include <linux/mii.h>
#include <asm/io.h>
-#include <asm/hardware.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/netx-regs.h>
-#include <asm/arch/pfifo.h>
-#include <asm/arch/xc.h>
-#include <asm/arch/eth.h>
+#include <mach/hardware.h>
+#include <mach/netx-regs.h>
+#include <mach/pfifo.h>
+#include <mach/xc.h>
+#include <mach/eth.h>
/* XC Fifo Offsets */
#define EMPTY_PTR_FIFO(xcno) (0 + ((xcno) << 3)) /* Index of the empty pointer FIFO */
NETXEN_BRDTYPE_P3_10000_BASE_T = 0x0027,
NETXEN_BRDTYPE_P3_XG_LOM = 0x0028,
NETXEN_BRDTYPE_P3_4_GB_MM = 0x0029,
+ NETXEN_BRDTYPE_P3_10G_SFP_CT = 0x002a,
+ NETXEN_BRDTYPE_P3_10G_SFP_QT = 0x002b,
NETXEN_BRDTYPE_P3_10G_CX4 = 0x0031,
NETXEN_BRDTYPE_P3_10G_XFP = 0x0032
nx_nic_intr_coalesce_data_t irq;
} nx_nic_intr_coalesce_t;
+#define NX_HOST_REQUEST 0x13
+#define NX_NIC_REQUEST 0x14
+
+#define NX_MAC_EVENT 0x1
+
+enum {
+ NX_NIC_H2C_OPCODE_START = 0,
+ NX_NIC_H2C_OPCODE_CONFIG_RSS,
+ NX_NIC_H2C_OPCODE_CONFIG_RSS_TBL,
+ NX_NIC_H2C_OPCODE_CONFIG_INTR_COALESCE,
+ NX_NIC_H2C_OPCODE_CONFIG_LED,
+ NX_NIC_H2C_OPCODE_CONFIG_PROMISCUOUS,
+ NX_NIC_H2C_OPCODE_CONFIG_L2_MAC,
+ NX_NIC_H2C_OPCODE_LRO_REQUEST,
+ NX_NIC_H2C_OPCODE_GET_SNMP_STATS,
+ NX_NIC_H2C_OPCODE_PROXY_START_REQUEST,
+ NX_NIC_H2C_OPCODE_PROXY_STOP_REQUEST,
+ NX_NIC_H2C_OPCODE_PROXY_SET_MTU,
+ NX_NIC_H2C_OPCODE_PROXY_SET_VPORT_MISS_MODE,
+ NX_H2P_OPCODE_GET_FINGER_PRINT_REQUEST,
+ NX_H2P_OPCODE_INSTALL_LICENSE_REQUEST,
+ NX_H2P_OPCODE_GET_LICENSE_CAPABILITY_REQUEST,
+ NX_NIC_H2C_OPCODE_GET_NET_STATS,
+ NX_NIC_H2C_OPCODE_LAST
+};
+
+#define VPORT_MISS_MODE_DROP 0 /* drop all unmatched */
+#define VPORT_MISS_MODE_ACCEPT_ALL 1 /* accept all packets */
+#define VPORT_MISS_MODE_ACCEPT_MULTI 2 /* accept unmatched multicast */
+
typedef struct {
u64 qhdr;
u64 req_hdr;
int (*disable_phy_interrupts) (struct netxen_adapter *);
int (*macaddr_set) (struct netxen_adapter *, netxen_ethernet_macaddr_t);
int (*set_mtu) (struct netxen_adapter *, int);
- int (*set_promisc) (struct netxen_adapter *, netxen_niu_prom_mode_t);
+ int (*set_promisc) (struct netxen_adapter *, u32);
int (*phy_read) (struct netxen_adapter *, long reg, u32 *);
int (*phy_write) (struct netxen_adapter *, long reg, u32 val);
int (*init_port) (struct netxen_adapter *, int);
u32 netxen_process_rcv_ring(struct netxen_adapter *adapter, int ctx, int max);
void netxen_p2_nic_set_multi(struct net_device *netdev);
void netxen_p3_nic_set_multi(struct net_device *netdev);
+int netxen_p3_nic_set_promisc(struct netxen_adapter *adapter, u32);
int netxen_config_intr_coalesce(struct netxen_adapter *adapter);
-u32 nx_fw_cmd_set_mtu(struct netxen_adapter *adapter, u32 mtu);
+int nx_fw_cmd_set_mtu(struct netxen_adapter *adapter, int mtu);
int netxen_nic_change_mtu(struct net_device *netdev, int new_mtu);
int netxen_nic_set_mac(struct net_device *netdev, void *p);
{NETXEN_BRDTYPE_P3_10G_SFP_PLUS, 2, "Dual XGb SFP+ LP"},
{NETXEN_BRDTYPE_P3_10000_BASE_T, 1, "XGB 10G BaseT LP"},
{NETXEN_BRDTYPE_P3_XG_LOM, 2, "Dual XGb LOM"},
- {NETXEN_BRDTYPE_P3_4_GB_MM, 4, "Quad GB - March Madness"},
+ {NETXEN_BRDTYPE_P3_4_GB_MM, 4, "NX3031 Gigabit Ethernet"},
+ {NETXEN_BRDTYPE_P3_10G_SFP_CT, 2, "NX3031 10 Gigabit Ethernet"},
+ {NETXEN_BRDTYPE_P3_10G_SFP_QT, 2, "Quanta Dual XGb SFP+"},
{NETXEN_BRDTYPE_P3_10G_CX4, 2, "Reference Dual CX4 Option"},
{NETXEN_BRDTYPE_P3_10G_XFP, 1, "Reference Single XFP Option"}
};
return rcode;
}
-u32
-nx_fw_cmd_set_mtu(struct netxen_adapter *adapter, u32 mtu)
+int
+nx_fw_cmd_set_mtu(struct netxen_adapter *adapter, int mtu)
{
u32 rcode = NX_RCODE_SUCCESS;
struct netxen_recv_context *recv_ctx = &adapter->recv_ctx[0];
0,
NX_CDRP_CMD_SET_MTU);
- return rcode;
+ if (rcode != NX_RCODE_SUCCESS)
+ return -EIO;
+
+ return 0;
}
static int
if (netif_running(dev)) {
ecmd->speed = adapter->link_speed;
ecmd->duplex = adapter->link_duplex;
- } else
- return -EIO; /* link absent */
+ ecmd->autoneg = adapter->link_autoneg;
+ }
+
} else if (adapter->ahw.board_type == NETXEN_NIC_XGBE) {
- ecmd->supported = (SUPPORTED_TP |
- SUPPORTED_1000baseT_Full |
- SUPPORTED_10000baseT_Full);
- ecmd->advertising = (ADVERTISED_TP |
- ADVERTISED_1000baseT_Full |
- ADVERTISED_10000baseT_Full);
+ u32 val;
+
+ adapter->hw_read_wx(adapter, NETXEN_PORT_MODE_ADDR, &val, 4);
+ if (val == NETXEN_PORT_MODE_802_3_AP) {
+ ecmd->supported = SUPPORTED_1000baseT_Full;
+ ecmd->advertising = ADVERTISED_1000baseT_Full;
+ } else {
+ ecmd->supported = SUPPORTED_10000baseT_Full;
+ ecmd->advertising = ADVERTISED_10000baseT_Full;
+ }
+
ecmd->port = PORT_TP;
- ecmd->speed = SPEED_10000;
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) {
+ u16 pcifn = adapter->ahw.pci_func;
+
+ adapter->hw_read_wx(adapter,
+ P3_LINK_SPEED_REG(pcifn), &val, 4);
+ ecmd->speed = P3_LINK_SPEED_MHZ *
+ P3_LINK_SPEED_VAL(pcifn, val);
+ } else
+ ecmd->speed = SPEED_10000;
+
ecmd->duplex = DUPLEX_FULL;
ecmd->autoneg = AUTONEG_DISABLE;
} else
break;
case NETXEN_BRDTYPE_P2_SB31_10G:
case NETXEN_BRDTYPE_P3_10G_SFP_PLUS:
+ case NETXEN_BRDTYPE_P3_10G_SFP_CT:
+ case NETXEN_BRDTYPE_P3_10G_SFP_QT:
case NETXEN_BRDTYPE_P3_10G_XFP:
ecmd->supported |= SUPPORTED_FIBRE;
ecmd->advertising |= ADVERTISED_FIBRE;
#define XG_LINK_STATE_P3(pcifn,val) \
(((val) >> ((pcifn) * 4)) & XG_LINK_STATE_P3_MASK)
+#define P3_LINK_SPEED_MHZ 100
+#define P3_LINK_SPEED_MASK 0xff
+#define P3_LINK_SPEED_REG(pcifn) \
+ (CRB_PF_LINK_SPEED_1 + (((pcifn) / 4) * 4))
+#define P3_LINK_SPEED_VAL(pcifn, reg) \
+ (((reg) >> (8 * ((pcifn) & 0x3))) & P3_LINK_SPEED_MASK)
+
#define NETXEN_CAM_RAM_BASE (NETXEN_CRB_CAM + 0x02000)
#define NETXEN_CAM_RAM(reg) (NETXEN_CAM_RAM_BASE + (reg))
#define NETXEN_FW_VERSION_MAJOR (NETXEN_CAM_RAM(0x150))
#define PCIE_SETUP_FUNCTION (0x12040)
#define PCIE_SETUP_FUNCTION2 (0x12048)
+#define PCIE_MISCCFG_RC (0x1206c)
#define PCIE_TGT_SPLIT_CHICKEN (0x12080)
#define PCIE_CHICKEN3 (0x120c8)
+#define ISR_INT_STATE_REG (NETXEN_PCIX_PS_REG(PCIE_MISCCFG_RC))
#define PCIE_MAX_MASTER_SPLIT (0x14048)
#define NETXEN_PORT_MODE_NONE 0
#define NETXEN_CAM_RAM_DMA_WATCHDOG_CTRL (0x14)
#define ISR_MSI_INT_TRIGGER(FUNC) (NETXEN_PCIX_PS_REG(PCIX_MSI_F(FUNC)))
+#define ISR_LEGACY_INT_TRIGGERED(VAL) (((VAL) & 0x300) == 0x200)
/*
* PCI Interrupt Vector Values.
#define ADDR_IN_RANGE(addr, low, high) \
(((addr) <= (high)) && ((addr) >= (low)))
-#define NETXEN_MAX_MTU 8000 + NETXEN_ENET_HEADER_SIZE + NETXEN_ETH_FCS_SIZE
-#define NETXEN_MIN_MTU 64
-#define NETXEN_ETH_FCS_SIZE 4
-#define NETXEN_ENET_HEADER_SIZE 14
#define NETXEN_WINDOW_ONE 0x2000000 /*CRB Window: bit 25 of CRB address */
-#define NETXEN_FIRMWARE_LEN ((16 * 1024) / 4)
-#define NETXEN_NIU_HDRSIZE (0x1 << 6)
-#define NETXEN_NIU_TLRSIZE (0x1 << 5)
#define NETXEN_NIC_ZERO_PAUSE_ADDR 0ULL
#define NETXEN_NIC_UNIT_PAUSE_ADDR 0x200ULL
return 0;
}
-#define NIC_REQUEST 0x14
-#define NETXEN_MAC_EVENT 0x1
-
static int nx_p3_sre_macaddr_change(struct net_device *dev,
u8 *addr, unsigned op)
{
int rv;
memset(&req, 0, sizeof(nx_nic_req_t));
- req.qhdr |= (NIC_REQUEST << 23);
- req.req_hdr |= NETXEN_MAC_EVENT;
+ req.qhdr |= (NX_NIC_REQUEST << 23);
+ req.req_hdr |= NX_MAC_EVENT;
req.req_hdr |= ((u64)adapter->portnum << 16);
mac_req.op = op;
memcpy(&mac_req.mac_addr, addr, 6);
nx_mac_list_t *cur, *next, *del_list, *add_list = NULL;
struct dev_mc_list *mc_ptr;
u8 bcast_addr[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
-
- adapter->set_promisc(adapter, NETXEN_NIU_PROMISC_MODE);
-
- /*
- * Programming mac addresses will automaticly enabling L2 filtering.
- * HW will replace timestamp with L2 conid when L2 filtering is
- * enabled. This causes problem for LSA. Do not enabling L2 filtering
- * until that problem is fixed.
- */
- if ((netdev->flags & IFF_PROMISC) ||
- (netdev->mc_count > adapter->max_mc_count))
- return;
+ u32 mode = VPORT_MISS_MODE_DROP;
del_list = adapter->mac_list;
adapter->mac_list = NULL;
nx_p3_nic_add_mac(adapter, netdev->dev_addr, &add_list, &del_list);
+ nx_p3_nic_add_mac(adapter, bcast_addr, &add_list, &del_list);
+
+ if (netdev->flags & IFF_PROMISC) {
+ mode = VPORT_MISS_MODE_ACCEPT_ALL;
+ goto send_fw_cmd;
+ }
+
+ if ((netdev->flags & IFF_ALLMULTI) ||
+ (netdev->mc_count > adapter->max_mc_count)) {
+ mode = VPORT_MISS_MODE_ACCEPT_MULTI;
+ goto send_fw_cmd;
+ }
+
if (netdev->mc_count > 0) {
- nx_p3_nic_add_mac(adapter, bcast_addr, &add_list, &del_list);
for (mc_ptr = netdev->mc_list; mc_ptr;
mc_ptr = mc_ptr->next) {
nx_p3_nic_add_mac(adapter, mc_ptr->dmi_addr,
&add_list, &del_list);
}
}
+
+send_fw_cmd:
+ adapter->set_promisc(adapter, mode);
for (cur = del_list; cur;) {
nx_p3_sre_macaddr_change(netdev, cur->mac_addr, NETXEN_MAC_DEL);
next = cur->next;
}
}
+int netxen_p3_nic_set_promisc(struct netxen_adapter *adapter, u32 mode)
+{
+ nx_nic_req_t req;
+
+ memset(&req, 0, sizeof(nx_nic_req_t));
+
+ req.qhdr |= (NX_HOST_REQUEST << 23);
+ req.req_hdr |= NX_NIC_H2C_OPCODE_PROXY_SET_VPORT_MISS_MODE;
+ req.req_hdr |= ((u64)adapter->portnum << 16);
+ req.words[0] = cpu_to_le64(mode);
+
+ return netxen_send_cmd_descs(adapter,
+ (struct cmd_desc_type0 *)&req, 1);
+}
+
#define NETXEN_CONFIG_INTR_COALESCE 3
/*
memset(&req, 0, sizeof(nx_nic_req_t));
- req.qhdr |= (NIC_REQUEST << 23);
+ req.qhdr |= (NX_NIC_REQUEST << 23);
req.req_hdr |= NETXEN_CONFIG_INTR_COALESCE;
req.req_hdr |= ((u64)adapter->portnum << 16);
{
struct netxen_adapter *adapter = netdev_priv(netdev);
int max_mtu;
+ int rc = 0;
if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
max_mtu = P3_MAX_MTU;
}
if (adapter->set_mtu)
- adapter->set_mtu(adapter, mtu);
- netdev->mtu = mtu;
+ rc = adapter->set_mtu(adapter, mtu);
- mtu += MTU_FUDGE_FACTOR;
- if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
- nx_fw_cmd_set_mtu(adapter, mtu);
- else if (adapter->set_mtu)
- adapter->set_mtu(adapter, mtu);
+ if (!rc)
+ netdev->mtu = mtu;
- return 0;
+ return rc;
}
int netxen_is_flash_supported(struct netxen_adapter *adapter)
(netxen_nic_pci_is_same_window(adapter, off+size-1) == 0)) {
write_unlock_irqrestore(&adapter->adapter_lock, flags);
printk(KERN_ERR "%s out of bound pci memory access. "
- "offset is 0x%llx\n", netxen_nic_driver_name, off);
+ "offset is 0x%llx\n", netxen_nic_driver_name,
+ (unsigned long long)off);
return -1;
}
(netxen_nic_pci_is_same_window(adapter, off+size-1) == 0)) {
write_unlock_irqrestore(&adapter->adapter_lock, flags);
printk(KERN_ERR "%s out of bound pci memory access. "
- "offset is 0x%llx\n", netxen_nic_driver_name, off);
+ "offset is 0x%llx\n", netxen_nic_driver_name,
+ (unsigned long long)off);
return -1;
}
case NETXEN_BRDTYPE_P3_10G_CX4_LP:
case NETXEN_BRDTYPE_P3_IMEZ:
case NETXEN_BRDTYPE_P3_10G_SFP_PLUS:
+ case NETXEN_BRDTYPE_P3_10G_SFP_CT:
+ case NETXEN_BRDTYPE_P3_10G_SFP_QT:
case NETXEN_BRDTYPE_P3_10G_XFP:
case NETXEN_BRDTYPE_P3_10000_BASE_T:
default:
printk("%s: Unknown(%x)\n", netxen_nic_driver_name,
boardinfo->board_type);
+ rv = -ENODEV;
break;
}
int netxen_nic_set_mtu_gb(struct netxen_adapter *adapter, int new_mtu)
{
+ new_mtu += MTU_FUDGE_FACTOR;
netxen_nic_write_w0(adapter,
NETXEN_NIU_GB_MAX_FRAME_SIZE(adapter->physical_port),
new_mtu);
int netxen_nic_set_mtu_xgb(struct netxen_adapter *adapter, int new_mtu)
{
- new_mtu += NETXEN_NIU_HDRSIZE + NETXEN_NIU_TLRSIZE;
+ new_mtu += MTU_FUDGE_FACTOR;
if (adapter->physical_port == 0)
netxen_nic_write_w0(adapter, NETXEN_NIU_XGE_MAX_FRAME_SIZE,
new_mtu);
__u32 status;
__u32 autoneg;
__u32 mode;
+ __u32 port_mode;
netxen_nic_read_w0(adapter, NETXEN_NIU_MODE, &mode);
if (netxen_get_niu_enable_ge(mode)) { /* Gb 10/100/1000 Mbps mode */
+
+ adapter->hw_read_wx(adapter,
+ NETXEN_PORT_MODE_ADDR, &port_mode, 4);
+ if (port_mode == NETXEN_PORT_MODE_802_3_AP) {
+ adapter->link_speed = SPEED_1000;
+ adapter->link_duplex = DUPLEX_FULL;
+ adapter->link_autoneg = AUTONEG_DISABLE;
+ return;
+ }
+
if (adapter->phy_read
- && adapter->
- phy_read(adapter,
+ && adapter->phy_read(adapter,
NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS,
&status) == 0) {
if (netxen_get_phy_link(status)) {
break;
}
if (adapter->phy_read
- && adapter->
- phy_read(adapter,
+ && adapter->phy_read(adapter,
NETXEN_NIU_GB_MII_MGMT_ADDR_AUTONEG,
&autoneg) != 0)
adapter->link_autoneg = autoneg;
#define netxen_get_niu_enable_ge(config_word) \
_netxen_crb_get_bit(config_word, 1)
-/* Promiscous mode options (GbE mode only) */
-typedef enum {
- NETXEN_NIU_PROMISC_MODE = 0,
- NETXEN_NIU_NON_PROMISC_MODE,
- NETXEN_NIU_ALLMULTI_MODE
-} netxen_niu_prom_mode_t;
+#define NETXEN_NIU_NON_PROMISC_MODE 0
+#define NETXEN_NIU_PROMISC_MODE 1
+#define NETXEN_NIU_ALLMULTI_MODE 2
/*
* NIU GB Drop CRC Register
/* Set promiscuous mode for a GbE interface */
int netxen_niu_set_promiscuous_mode(struct netxen_adapter *adapter,
- netxen_niu_prom_mode_t mode);
+ u32 mode);
int netxen_niu_xg_set_promiscuous_mode(struct netxen_adapter *adapter,
- netxen_niu_prom_mode_t mode);
+ u32 mode);
/* set the MAC address for a given MAC */
int netxen_niu_macaddr_set(struct netxen_adapter *adapter,
default:
break;
}
+
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) {
+ adapter->set_mtu = nx_fw_cmd_set_mtu;
+ adapter->set_promisc = netxen_p3_nic_set_promisc;
+ }
}
/*
if (!NETXEN_IS_MSI_FAMILY(adapter)) {
do {
adapter->pci_write_immediate(adapter,
- ISR_INT_TARGET_STATUS, 0xffffffff);
+ adapter->legacy_intr.tgt_status_reg,
+ 0xffffffff);
mask = adapter->pci_read_immediate(adapter,
ISR_INT_VECTOR);
if (!(mask & 0x80))
} while (--retries);
if (!retries) {
- printk(KERN_NOTICE "%s: Failed to disable interrupt completely\n",
+ printk(KERN_NOTICE "%s: Failed to disable interrupt\n",
netxen_nic_driver_name);
}
} else {
{
u32 mask;
- DPRINTK(1, INFO, "Entered ISR Enable \n");
-
if (adapter->intr_scheme != -1 &&
adapter->intr_scheme != INTR_SCHEME_PERPORT) {
switch (adapter->ahw.board_type) {
if (!NETXEN_IS_MSI_FAMILY(adapter)) {
mask = 0xbff;
- if (adapter->intr_scheme != -1 &&
- adapter->intr_scheme != INTR_SCHEME_PERPORT) {
+ if (adapter->intr_scheme == INTR_SCHEME_PERPORT)
+ adapter->pci_write_immediate(adapter,
+ adapter->legacy_intr.tgt_mask_reg, mask);
+ else
adapter->pci_write_normalize(adapter,
CRB_INT_VECTOR, 0);
- }
- adapter->pci_write_immediate(adapter,
- ISR_INT_TARGET_MASK, mask);
}
-
- DPRINTK(1, INFO, "Done with enable Int\n");
}
static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id)
case NETXEN_BRDTYPE_P3_10G_CX4_LP:
case NETXEN_BRDTYPE_P3_IMEZ:
case NETXEN_BRDTYPE_P3_10G_SFP_PLUS:
+ case NETXEN_BRDTYPE_P3_10G_SFP_QT:
+ case NETXEN_BRDTYPE_P3_10G_SFP_CT:
case NETXEN_BRDTYPE_P3_10G_XFP:
case NETXEN_BRDTYPE_P3_10000_BASE_T:
adapter->msix_supported = !!use_msi_x;
case NETXEN_BRDTYPE_P3_REF_QG:
case NETXEN_BRDTYPE_P3_4_GB:
case NETXEN_BRDTYPE_P3_4_GB_MM:
+ adapter->msix_supported = 0;
+ adapter->max_rx_desc_count = MAX_RCV_DESCRIPTORS_10G;
+ break;
+
case NETXEN_BRDTYPE_P2_SB35_4G:
case NETXEN_BRDTYPE_P2_SB31_2G:
adapter->msix_supported = 0;
adapter->status &= ~NETXEN_NETDEV_STATUS;
adapter->rx_csum = 1;
adapter->mc_enabled = 0;
- if (NX_IS_REVISION_P3(revision_id)) {
+ if (NX_IS_REVISION_P3(revision_id))
adapter->max_mc_count = 38;
- adapter->max_rds_rings = 2;
- } else {
+ else
adapter->max_mc_count = 16;
- adapter->max_rds_rings = 3;
- }
netdev->open = netxen_nic_open;
netdev->stop = netxen_nic_close;
if (adapter->portnum == 0)
first_driver = 1;
}
- adapter->crb_addr_cmd_producer = crb_cmd_producer[adapter->portnum];
- adapter->crb_addr_cmd_consumer = crb_cmd_consumer[adapter->portnum];
- netxen_nic_update_cmd_producer(adapter, 0);
- netxen_nic_update_cmd_consumer(adapter, 0);
if (first_driver) {
first_boot = adapter->pci_read_normalize(adapter,
return -EIO;
}
+ if (adapter->fw_major < 4)
+ adapter->max_rds_rings = 3;
+ else
+ adapter->max_rds_rings = 2;
+
err = netxen_alloc_sw_resources(adapter);
if (err) {
printk(KERN_ERR "%s: Error in setting sw resources\n",
crb_cmd_producer[adapter->portnum];
adapter->crb_addr_cmd_consumer =
crb_cmd_consumer[adapter->portnum];
- }
- netxen_nic_update_cmd_producer(adapter, 0);
- netxen_nic_update_cmd_consumer(adapter, 0);
+ netxen_nic_update_cmd_producer(adapter, 0);
+ netxen_nic_update_cmd_consumer(adapter, 0);
+ }
for (ctx = 0; ctx < MAX_RCV_CTX; ++ctx) {
for (ring = 0; ring < adapter->max_rds_rings; ring++)
netxen_nic_set_link_parameters(adapter);
netdev->set_multicast_list(netdev);
- if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
- nx_fw_cmd_set_mtu(adapter, netdev->mtu);
- else
+ if (adapter->set_mtu)
adapter->set_mtu(adapter, netdev->mtu);
mod_timer(&adapter->watchdog_timer, jiffies);
port = adapter->physical_port;
- if (adapter->ahw.board_type == NETXEN_NIC_GBE) {
- val = adapter->pci_read_normalize(adapter, CRB_XG_STATE);
- linkup = (val >> port) & 1;
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) {
+ val = adapter->pci_read_normalize(adapter, CRB_XG_STATE_P3);
+ val = XG_LINK_STATE_P3(adapter->ahw.pci_func, val);
+ linkup = (val == XG_LINK_UP_P3);
} else {
- if (adapter->fw_major < 4) {
- val = adapter->pci_read_normalize(adapter,
- CRB_XG_STATE);
+ val = adapter->pci_read_normalize(adapter, CRB_XG_STATE);
+ if (adapter->ahw.board_type == NETXEN_NIC_GBE)
+ linkup = (val >> port) & 1;
+ else {
val = (val >> port*8) & 0xff;
linkup = (val == XG_LINK_UP);
- } else {
- val = adapter->pci_read_normalize(adapter,
- CRB_XG_STATE_P3);
- val = XG_LINK_STATE_P3(adapter->ahw.pci_func, val);
- linkup = (val == XG_LINK_UP_P3);
}
}
struct netxen_adapter *adapter = data;
u32 our_int = 0;
- our_int = adapter->pci_read_normalize(adapter, CRB_INT_VECTOR);
- /* not our interrupt */
- if ((our_int & (0x80 << adapter->portnum)) == 0)
+ u32 status = 0;
+
+ status = adapter->pci_read_immediate(adapter, ISR_INT_VECTOR);
+
+ if (!(status & adapter->legacy_intr.int_vec_bit))
return IRQ_NONE;
- if (adapter->intr_scheme == INTR_SCHEME_PERPORT) {
- /* claim interrupt */
- adapter->pci_write_normalize(adapter, CRB_INT_VECTOR,
+ if (adapter->ahw.revision_id >= NX_P3_B1) {
+ /* check interrupt state machine, to be sure */
+ status = adapter->pci_read_immediate(adapter,
+ ISR_INT_STATE_REG);
+ if (!ISR_LEGACY_INT_TRIGGERED(status))
+ return IRQ_NONE;
+
+ } else if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) {
+
+ our_int = adapter->pci_read_normalize(adapter, CRB_INT_VECTOR);
+ /* not our interrupt */
+ if ((our_int & (0x80 << adapter->portnum)) == 0)
+ return IRQ_NONE;
+
+ if (adapter->intr_scheme == INTR_SCHEME_PERPORT) {
+ /* claim interrupt */
+ adapter->pci_write_normalize(adapter,
+ CRB_INT_VECTOR,
our_int & ~((u32)(0x80 << adapter->portnum)));
+ }
}
netxen_handle_int(adapter);
int i;
DECLARE_MAC_BUF(mac);
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
+ return 0;
+
for (i = 0; i < 10; i++) {
temp[0] = temp[1] = 0;
memcpy(temp + 2, addr, 2);
__u32 mac_cfg0;
u32 port = adapter->physical_port;
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
+ return 0;
+
if (port > NETXEN_NIU_MAX_GBE_PORTS)
return -EINVAL;
mac_cfg0 = 0;
__u32 mac_cfg;
u32 port = adapter->physical_port;
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
+ return 0;
+
if (port > NETXEN_NIU_MAX_XG_PORTS)
return -EINVAL;
/* Set promiscuous mode for a GbE interface */
int netxen_niu_set_promiscuous_mode(struct netxen_adapter *adapter,
- netxen_niu_prom_mode_t mode)
+ u32 mode)
{
__u32 reg;
u32 port = adapter->physical_port;
u8 temp[4];
u32 val;
+ if (NX_IS_REVISION_P3(adapter->ahw.revision_id))
+ return 0;
+
if ((phy < 0) || (phy > NETXEN_NIU_MAX_XG_PORTS))
return -EIO;
#endif /* 0 */
int netxen_niu_xg_set_promiscuous_mode(struct netxen_adapter *adapter,
- netxen_niu_prom_mode_t mode)
+ u32 mode)
{
__u32 reg;
u32 port = adapter->physical_port;
#define CRB_HOST_STS_PROD NETXEN_NIC_REG(0xdc)
#define CRB_HOST_STS_CONS NETXEN_NIC_REG(0xe0)
#define CRB_PEG_CMD_PROD NETXEN_NIC_REG(0xe4)
-#define CRB_PEG_CMD_CONS NETXEN_NIC_REG(0xe8)
-#define CRB_HOST_BUFFER_PROD NETXEN_NIC_REG(0xec)
+#define CRB_PF_LINK_SPEED_1 NETXEN_NIC_REG(0xe8)
+#define CRB_PF_LINK_SPEED_2 NETXEN_NIC_REG(0xec)
#define CRB_HOST_BUFFER_CONS NETXEN_NIC_REG(0xf0)
#define CRB_JUMBO_BUFFER_PROD NETXEN_NIC_REG(0xf4)
#define CRB_JUMBO_BUFFER_CONS NETXEN_NIC_REG(0xf8)
PRINTK2((KERN_DEBUG "%s: entering set_multicast_list\n", dev->name));
if (dev->flags&IFF_PROMISC || dev->flags&IFF_ALLMULTI || dev->mc_list) {
- dev->flags |= IFF_PROMISC;
outb(RMD_PROMISC, EDLC_RMODE); /* Enable promiscuous mode */
PRINTK((KERN_DEBUG "%s: Entering promiscuous mode\n", dev->name));
} else {
if (num_addrs > len) {
printk(KERN_ERR "%s: switching to promisc. mode\n",
dev->name);
- dev->flags |= IFF_PROMISC;
+ writeb(0x01, &cfg_cmd->promisc);
}
}
if (dev->flags & IFF_PROMISC)
*class = CLASS_CODE_SCTP_IPV6;
break;
default:
- return -1;
+ return 0;
}
return 1;
struct gelic_wl_info *wl = port_wl(netdev_priv(netdev));
struct iw_point *enc = &data->encoding;
__u16 flags;
- unsigned int irqflag;
+ unsigned long irqflag;
int key_index, index_specified;
int ret = 0;
{
struct gelic_wl_info *wl = port_wl(netdev_priv(netdev));
struct iw_point *enc = &data->encoding;
- unsigned int irqflag;
+ unsigned long irqflag;
unsigned int key_index, index_specified;
int ret = 0;
struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
__u16 alg;
__u16 flags;
- unsigned int irqflag;
+ unsigned long irqflag;
int key_index;
int ret = 0;
struct gelic_wl_info *wl = port_wl(netdev_priv(netdev));
struct iw_point *enc = &data->encoding;
struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
- unsigned int irqflag;
+ unsigned long irqflag;
int key_index;
int ret = 0;
int max_key_len;
{
struct gelic_wl_info *wl = port_wl(netdev_priv(net_dev));
unsigned int len;
- unsigned int irqflag;
+ unsigned long irqflag;
int ret = 0;
pr_debug("%s:<- len=%d\n", __func__, data->data.length);
{
struct gelic_wl_info *wl = port_wl(netdev_priv(net_dev));
char *p;
- unsigned int irqflag;
+ unsigned long irqflag;
unsigned int i;
pr_debug("%s:<-\n", __func__);
#define DRV_NAME "qla3xxx"
#define DRV_STRING "QLogic ISP3XXX Network Driver"
-#define DRV_VERSION "v2.03.00-k4"
+#define DRV_VERSION "v2.03.00-k5"
#define PFX DRV_NAME " "
static const char ql3xxx_driver_name[] = DRV_NAME;
case ISP_CONTROL_FN0_NET:
qdev->mac_index = 0;
qdev->mac_ob_opcode = OUTBOUND_MAC_IOCB | func_number;
- qdev->tcp_ob_opcode = OUTBOUND_TCP_IOCB | func_number;
- qdev->update_ob_opcode = UPDATE_NCB_IOCB | func_number;
qdev->mb_bit_mask = FN0_MA_BITS_MASK;
qdev->PHYAddr = PORT0_PHY_ADDRESS;
if (port_status & PORT_STATUS_SM0)
case ISP_CONTROL_FN1_NET:
qdev->mac_index = 1;
qdev->mac_ob_opcode = OUTBOUND_MAC_IOCB | func_number;
- qdev->tcp_ob_opcode = OUTBOUND_TCP_IOCB | func_number;
- qdev->update_ob_opcode = UPDATE_NCB_IOCB | func_number;
qdev->mb_bit_mask = FN1_MA_BITS_MASK;
qdev->PHYAddr = PORT1_PHY_ADDRESS;
if (port_status & PORT_STATUS_SM1)
return (ql_adapter_up(qdev));
}
-static void ql3xxx_set_multicast_list(struct net_device *ndev)
-{
- /*
- * We are manually parsing the list in the net_device structure.
- */
- return;
-}
-
static int ql3xxx_set_mac_address(struct net_device *ndev, void *p)
{
struct ql3_adapter *qdev = (struct ql3_adapter *)netdev_priv(ndev);
ndev->open = ql3xxx_open;
ndev->hard_start_xmit = ql3xxx_send;
ndev->stop = ql3xxx_close;
- ndev->set_multicast_list = ql3xxx_set_multicast_list;
+ /* ndev->set_multicast_list
+ * This device is one side of a two-function adapter
+ * (NIC and iSCSI). Promiscuous mode setting/clearing is
+ * not allowed from the NIC side.
+ */
SET_ETHTOOL_OPS(ndev, &ql3xxx_ethtool_ops);
ndev->set_mac_address = ql3xxx_set_mac_address;
ndev->tx_timeout = ql3xxx_tx_timeout;
ndev->tx_queue_len = NUM_REQ_Q_ENTRIES;
- /* Turn off support for multicasting */
- ndev->flags &= ~IFF_MULTICAST;
-
/* Record PCI bus information. */
ql_get_board_info(qdev);
#define OPCODE_OB_MAC_IOCB_FN0 0x01
#define OPCODE_OB_MAC_IOCB_FN2 0x21
-#define OPCODE_OB_TCP_IOCB_FN0 0x03
-#define OPCODE_OB_TCP_IOCB_FN2 0x23
-#define OPCODE_UPDATE_NCB_IOCB_FN0 0x00
-#define OPCODE_UPDATE_NCB_IOCB_FN2 0x20
-#define OPCODE_UPDATE_NCB_IOCB 0xF0
#define OPCODE_IB_MAC_IOCB 0xF9
#define OPCODE_IB_3032_MAC_IOCB 0x09
#define OPCODE_IB_IP_IOCB 0xFA
#define OPCODE_IB_3032_IP_IOCB 0x0A
-#define OPCODE_IB_TCP_IOCB 0xFB
-#define OPCODE_DUMP_PROTO_IOCB 0xFE
-#define OPCODE_BUFFER_ALERT_IOCB 0xFB
#define OPCODE_FUNC_ID_MASK 0x30
#define OUTBOUND_MAC_IOCB 0x01 /* plus function bits */
-#define OUTBOUND_TCP_IOCB 0x03 /* plus function bits */
-#define UPDATE_NCB_IOCB 0x00 /* plus function bits */
#define FN0_MA_BITS_MASK 0x00
#define FN1_MA_BITS_MASK 0x80
__le32 reserved2;
};
-struct ob_tcp_iocb_req {
- u8 opcode;
-
- u8 flags0;
-#define OB_TCP_IOCB_REQ_P 0x80
-#define OB_TCP_IOCB_REQ_CI 0x20
-#define OB_TCP_IOCB_REQ_H 0x10
-#define OB_TCP_IOCB_REQ_LN 0x08
-#define OB_TCP_IOCB_REQ_K 0x04
-#define OB_TCP_IOCB_REQ_D 0x02
-#define OB_TCP_IOCB_REQ_I 0x01
-
- u8 flags1;
-#define OB_TCP_IOCB_REQ_OSM 0x40
-#define OB_TCP_IOCB_REQ_URG 0x20
-#define OB_TCP_IOCB_REQ_ACK 0x10
-#define OB_TCP_IOCB_REQ_PSH 0x08
-#define OB_TCP_IOCB_REQ_RST 0x04
-#define OB_TCP_IOCB_REQ_SYN 0x02
-#define OB_TCP_IOCB_REQ_FIN 0x01
-
- u8 options_len;
-#define OB_TCP_IOCB_REQ_OMASK 0xF0
-#define OB_TCP_IOCB_REQ_SHIFT 4
-
- __le32 transaction_id;
- __le32 data_len;
- __le32 hncb_ptr_low;
- __le32 hncb_ptr_high;
- __le32 buf_addr0_low;
- __le32 buf_addr0_high;
- __le32 buf_0_len;
- __le32 buf_addr1_low;
- __le32 buf_addr1_high;
- __le32 buf_1_len;
- __le32 buf_addr2_low;
- __le32 buf_addr2_high;
- __le32 buf_2_len;
- __le32 time_stamp;
- __le32 reserved1;
-};
-
-struct ob_tcp_iocb_rsp {
- u8 opcode;
-
- u8 flags0;
-#define OB_TCP_IOCB_RSP_C 0x20
-#define OB_TCP_IOCB_RSP_H 0x10
-#define OB_TCP_IOCB_RSP_LN 0x08
-#define OB_TCP_IOCB_RSP_K 0x04
-#define OB_TCP_IOCB_RSP_D 0x02
-#define OB_TCP_IOCB_RSP_I 0x01
-
- u8 flags1;
-#define OB_TCP_IOCB_RSP_E 0x10
-#define OB_TCP_IOCB_RSP_W 0x08
-#define OB_TCP_IOCB_RSP_P 0x04
-#define OB_TCP_IOCB_RSP_T 0x02
-#define OB_TCP_IOCB_RSP_F 0x01
-
- u8 state;
-#define OB_TCP_IOCB_RSP_SMASK 0xF0
-#define OB_TCP_IOCB_RSP_SHIFT 4
-
- __le32 transaction_id;
- __le32 local_ncb_ptr;
- __le32 reserved0;
-};
-
struct ib_ip_iocb_rsp {
u8 opcode;
#define IB_IP_IOCB_RSP_3032_V 0x80
__le32 ial_high;
};
-struct ib_tcp_iocb_rsp {
- u8 opcode;
- u8 flags;
-#define IB_TCP_IOCB_RSP_P 0x80
-#define IB_TCP_IOCB_RSP_T 0x40
-#define IB_TCP_IOCB_RSP_D 0x20
-#define IB_TCP_IOCB_RSP_N 0x10
-#define IB_TCP_IOCB_RSP_IP 0x03
-#define IB_TCP_FLAG_MASK 0xf0
-#define IB_TCP_FLAG_IOCB_SYN 0x00
-
-#define TCP_IB_RSP_FLAGS(x) (x->flags & ~IB_TCP_FLAG_MASK)
-
- __le16 length;
- __le32 hncb_ref_num;
- __le32 ial_low;
- __le32 ial_high;
-};
-
struct net_rsp_iocb {
u8 opcode;
u8 flags;
u32 small_buf_release_cnt;
u32 small_buf_total_size;
- /* ISR related, saves status for DPC. */
- u32 control_status;
-
struct eeprom_data nvram_data;
- struct timer_list ioctl_timer;
u32 port_link_state;
- u32 last_rsp_offset;
/* 4022 specific */
u32 mac_index; /* Driver's MAC number can be 0 or 1 for first and second networking functions respectively */
u32 PHYAddr; /* Address of PHY 0x1e00 Port 0 and 0x1f00 Port 1 */
u32 mac_ob_opcode; /* Opcode to use on mac transmission */
- u32 tcp_ob_opcode; /* Opcode to use on tcp transmission */
- u32 update_ob_opcode; /* Opcode to use for updating NCB */
u32 mb_bit_mask; /* MA Bits mask to use on transmission */
u32 numPorts;
struct workqueue_struct *workqueue;
pkt_cnt++;
/* Updating the statistics block */
- nic->stats.tx_bytes += skb->len;
+ nic->dev->stats.tx_bytes += skb->len;
nic->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
dev_kfree_skb_irq(skb);
/* Configure Stats for immediate updt */
s2io_updt_stats(sp);
+ /* Using sp->stats as a staging area, because reset (due to mtu
+ change, for example) will clear some hardware counters */
+ dev->stats.tx_packets +=
+ le32_to_cpu(mac_control->stats_info->tmac_frms) -
+ sp->stats.tx_packets;
sp->stats.tx_packets =
le32_to_cpu(mac_control->stats_info->tmac_frms);
+ dev->stats.tx_errors +=
+ le32_to_cpu(mac_control->stats_info->tmac_any_err_frms) -
+ sp->stats.tx_errors;
sp->stats.tx_errors =
le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
+ dev->stats.rx_errors +=
+ le64_to_cpu(mac_control->stats_info->rmac_drop_frms) -
+ sp->stats.rx_errors;
sp->stats.rx_errors =
le64_to_cpu(mac_control->stats_info->rmac_drop_frms);
+ dev->stats.multicast =
+ le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms) -
+ sp->stats.multicast;
sp->stats.multicast =
le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
+ dev->stats.rx_length_errors =
+ le64_to_cpu(mac_control->stats_info->rmac_long_frms) -
+ sp->stats.rx_length_errors;
sp->stats.rx_length_errors =
le64_to_cpu(mac_control->stats_info->rmac_long_frms);
/* collect per-ring rx_packets and rx_bytes */
- sp->stats.rx_packets = sp->stats.rx_bytes = 0;
+ dev->stats.rx_packets = dev->stats.rx_bytes = 0;
for (i = 0; i < config->rx_ring_num; i++) {
- sp->stats.rx_packets += mac_control->rings[i].rx_packets;
- sp->stats.rx_bytes += mac_control->rings[i].rx_bytes;
+ dev->stats.rx_packets += mac_control->rings[i].rx_packets;
+ dev->stats.rx_bytes += mac_control->rings[i].rx_bytes;
}
- return (&sp->stats);
+ return (&dev->stats);
}
/**
if (err_mask != 0x5) {
DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
dev->name, err_mask);
- sp->stats.rx_crc_errors++;
+ dev->stats.rx_crc_errors++;
sp->mac_control.stats_info->sw_stat.mem_freed
+= skb->truesize;
dev_kfree_skb(skb);
/*
* SuperH Ethernet device driver
*
- * Copyright (C) 2006,2007 Nobuhiro Iwamatsu
+ * Copyright (C) 2006-2008 Nobuhiro Iwamatsu
* Copyright (C) 2008 Renesas Solutions Corp.
*
* This program is free software; you can redistribute it and/or modify it
#include "sh_eth.h"
+/* CPU <-> EDMAC endian convert */
+static inline __u32 cpu_to_edmac(struct sh_eth_private *mdp, u32 x)
+{
+ switch (mdp->edmac_endian) {
+ case EDMAC_LITTLE_ENDIAN:
+ return cpu_to_le32(x);
+ case EDMAC_BIG_ENDIAN:
+ return cpu_to_be32(x);
+ }
+ return x;
+}
+
+static inline __u32 edmac_to_cpu(struct sh_eth_private *mdp, u32 x)
+{
+ switch (mdp->edmac_endian) {
+ case EDMAC_LITTLE_ENDIAN:
+ return le32_to_cpu(x);
+ case EDMAC_BIG_ENDIAN:
+ return be32_to_cpu(x);
+ }
+ return x;
+}
+
/*
* Program the hardware MAC address from dev->dev_addr.
*/
.get_mdio_data = sh_get_mdio,
};
+/* Chip Reset */
static void sh_eth_reset(struct net_device *ndev)
{
u32 ioaddr = ndev->base_addr;
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ int cnt = 100;
+
+ ctrl_outl(EDSR_ENALL, ioaddr + EDSR);
+ ctrl_outl(ctrl_inl(ioaddr + EDMR) | EDMR_SRST, ioaddr + EDMR);
+ while (cnt > 0) {
+ if (!(ctrl_inl(ioaddr + EDMR) & 0x3))
+ break;
+ mdelay(1);
+ cnt--;
+ }
+ if (cnt < 0)
+ printk(KERN_ERR "Device reset fail\n");
+
+ /* Table Init */
+ ctrl_outl(0x0, ioaddr + TDLAR);
+ ctrl_outl(0x0, ioaddr + TDFAR);
+ ctrl_outl(0x0, ioaddr + TDFXR);
+ ctrl_outl(0x0, ioaddr + TDFFR);
+ ctrl_outl(0x0, ioaddr + RDLAR);
+ ctrl_outl(0x0, ioaddr + RDFAR);
+ ctrl_outl(0x0, ioaddr + RDFXR);
+ ctrl_outl(0x0, ioaddr + RDFFR);
+#else
ctrl_outl(ctrl_inl(ioaddr + EDMR) | EDMR_SRST, ioaddr + EDMR);
mdelay(3);
ctrl_outl(ctrl_inl(ioaddr + EDMR) & ~EDMR_SRST, ioaddr + EDMR);
+#endif
}
/* free skb and descriptor buffer */
/* format skb and descriptor buffer */
static void sh_eth_ring_format(struct net_device *ndev)
{
+ u32 ioaddr = ndev->base_addr, reserve = 0;
struct sh_eth_private *mdp = netdev_priv(ndev);
int i;
struct sk_buff *skb;
mdp->rx_skbuff[i] = skb;
if (skb == NULL)
break;
- skb->dev = ndev; /* Mark as being used by this device. */
+ skb->dev = ndev; /* Mark as being used by this device. */
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ reserve = SH7763_SKB_ALIGN
+ - ((uint32_t)skb->data & (SH7763_SKB_ALIGN-1));
+ if (reserve)
+ skb_reserve(skb, reserve);
+#else
skb_reserve(skb, RX_OFFSET);
-
+#endif
/* RX descriptor */
rxdesc = &mdp->rx_ring[i];
rxdesc->addr = (u32)skb->data & ~0x3UL;
- rxdesc->status = cpu_to_le32(RD_RACT | RD_RFP);
+ rxdesc->status = cpu_to_edmac(mdp, RD_RACT | RD_RFP);
/* The size of the buffer is 16 byte boundary. */
rxdesc->buffer_length = (mdp->rx_buf_sz + 16) & ~0x0F;
+ /* Rx descriptor address set */
+ if (i == 0) {
+ ctrl_outl((u32)rxdesc, ioaddr + RDLAR);
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl((u32)rxdesc, ioaddr + RDFAR);
+#endif
+ }
}
+ /* Rx descriptor address set */
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl((u32)rxdesc, ioaddr + RDFXR);
+ ctrl_outl(0x1, ioaddr + RDFFR);
+#endif
+
mdp->dirty_rx = (u32) (i - RX_RING_SIZE);
/* Mark the last entry as wrapping the ring. */
- rxdesc->status |= cpu_to_le32(RC_RDEL);
+ rxdesc->status |= cpu_to_edmac(mdp, RD_RDEL);
memset(mdp->tx_ring, 0, tx_ringsize);
for (i = 0; i < TX_RING_SIZE; i++) {
mdp->tx_skbuff[i] = NULL;
txdesc = &mdp->tx_ring[i];
- txdesc->status = cpu_to_le32(TD_TFP);
+ txdesc->status = cpu_to_edmac(mdp, TD_TFP);
txdesc->buffer_length = 0;
+ if (i == 0) {
+ /* Tx descriptor address set */
+ ctrl_outl((u32)txdesc, ioaddr + TDLAR);
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl((u32)txdesc, ioaddr + TDFAR);
+#endif
+ }
}
- txdesc->status |= cpu_to_le32(TD_TDLE);
+ /* Tx descriptor address set */
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl((u32)txdesc, ioaddr + TDFXR);
+ ctrl_outl(0x1, ioaddr + TDFFR);
+#endif
+
+ txdesc->status |= cpu_to_edmac(mdp, TD_TDLE);
}
/* Get skb and descriptor buffer */
/* Soft Reset */
sh_eth_reset(ndev);
- ctrl_outl(RPADIR_PADS1, ioaddr + RPADIR); /* SH7712-DMA-RX-PAD2 */
+ /* Descriptor format */
+ sh_eth_ring_format(ndev);
+ ctrl_outl(RPADIR_INIT, ioaddr + RPADIR);
/* all sh_eth int mask */
ctrl_outl(0, ioaddr + EESIPR);
- /* FIFO size set */
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl(EDMR_EL, ioaddr + EDMR);
+#else
ctrl_outl(0, ioaddr + EDMR); /* Endian change */
+#endif
+ /* FIFO size set */
ctrl_outl((FIFO_SIZE_T | FIFO_SIZE_R), ioaddr + FDR);
ctrl_outl(0, ioaddr + TFTR);
+ /* Frame recv control */
ctrl_outl(0, ioaddr + RMCR);
rx_int_var = mdp->rx_int_var = DESC_I_RINT8 | DESC_I_RINT5;
tx_int_var = mdp->tx_int_var = DESC_I_TINT2;
ctrl_outl(rx_int_var | tx_int_var, ioaddr + TRSCER);
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ /* Burst sycle set */
+ ctrl_outl(0x800, ioaddr + BCULR);
+#endif
+
ctrl_outl((FIFO_F_D_RFF | FIFO_F_D_RFD), ioaddr + FCFTR);
- ctrl_outl(0, ioaddr + TRIMD);
- /* Descriptor format */
- sh_eth_ring_format(ndev);
+#if !defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl(0, ioaddr + TRIMD);
+#endif
- ctrl_outl((u32)mdp->rx_ring, ioaddr + RDLAR);
- ctrl_outl((u32)mdp->tx_ring, ioaddr + TDLAR);
+ /* Recv frame limit set register */
+ ctrl_outl(RFLR_VALUE, ioaddr + RFLR);
ctrl_outl(ctrl_inl(ioaddr + EESR), ioaddr + EESR);
ctrl_outl((DMAC_M_RFRMER | DMAC_M_ECI | 0x003fffff), ioaddr + EESIPR);
ECMR_ZPF | (mdp->duplex ? ECMR_DM : 0) | ECMR_TE | ECMR_RE;
ctrl_outl(val, ioaddr + ECMR);
- ctrl_outl(ECSR_BRCRX | ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD |
- ECSIPR_MPDIP, ioaddr + ECSR);
- ctrl_outl(ECSIPR_BRCRXIP | ECSIPR_PSRTOIP | ECSIPR_LCHNGIP |
- ECSIPR_ICDIP | ECSIPR_MPDIP, ioaddr + ECSIPR);
+
+ /* E-MAC Status Register clear */
+ ctrl_outl(ECSR_INIT, ioaddr + ECSR);
+
+ /* E-MAC Interrupt Enable register */
+ ctrl_outl(ECSIPR_INIT, ioaddr + ECSIPR);
/* Set MAC address */
update_mac_address(ndev);
/* mask reset */
-#if defined(CONFIG_CPU_SUBTYPE_SH7710)
+#if defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7763)
ctrl_outl(APR_AP, ioaddr + APR);
ctrl_outl(MPR_MP, ioaddr + MPR);
ctrl_outl(TPAUSER_UNLIMITED, ioaddr + TPAUSER);
+#endif
+#if defined(CONFIG_CPU_SUBTYPE_SH7710)
ctrl_outl(BCFR_UNLIMITED, ioaddr + BCFR);
#endif
+
/* Setting the Rx mode will start the Rx process. */
ctrl_outl(EDRRR_R, ioaddr + EDRRR);
for (; mdp->cur_tx - mdp->dirty_tx > 0; mdp->dirty_tx++) {
entry = mdp->dirty_tx % TX_RING_SIZE;
txdesc = &mdp->tx_ring[entry];
- if (txdesc->status & cpu_to_le32(TD_TACT))
+ if (txdesc->status & cpu_to_edmac(mdp, TD_TACT))
break;
/* Free the original skb. */
if (mdp->tx_skbuff[entry]) {
mdp->tx_skbuff[entry] = NULL;
freeNum++;
}
- txdesc->status = cpu_to_le32(TD_TFP);
+ txdesc->status = cpu_to_edmac(mdp, TD_TFP);
if (entry >= TX_RING_SIZE - 1)
- txdesc->status |= cpu_to_le32(TD_TDLE);
+ txdesc->status |= cpu_to_edmac(mdp, TD_TDLE);
mdp->stats.tx_packets++;
mdp->stats.tx_bytes += txdesc->buffer_length;
int boguscnt = (mdp->dirty_rx + RX_RING_SIZE) - mdp->cur_rx;
struct sk_buff *skb;
u16 pkt_len = 0;
- u32 desc_status;
+ u32 desc_status, reserve = 0;
rxdesc = &mdp->rx_ring[entry];
- while (!(rxdesc->status & cpu_to_le32(RD_RACT))) {
- desc_status = le32_to_cpu(rxdesc->status);
+ while (!(rxdesc->status & cpu_to_edmac(mdp, RD_RACT))) {
+ desc_status = edmac_to_cpu(mdp, rxdesc->status);
pkt_len = rxdesc->frame_length;
if (--boguscnt < 0)
mdp->stats.rx_packets++;
mdp->stats.rx_bytes += pkt_len;
}
- rxdesc->status |= cpu_to_le32(RD_RACT);
+ rxdesc->status |= cpu_to_edmac(mdp, RD_RACT);
entry = (++mdp->cur_rx) % RX_RING_SIZE;
}
for (; mdp->cur_rx - mdp->dirty_rx > 0; mdp->dirty_rx++) {
entry = mdp->dirty_rx % RX_RING_SIZE;
rxdesc = &mdp->rx_ring[entry];
+ /* The size of the buffer is 16 byte boundary. */
+ rxdesc->buffer_length = (mdp->rx_buf_sz + 16) & ~0x0F;
+
if (mdp->rx_skbuff[entry] == NULL) {
skb = dev_alloc_skb(mdp->rx_buf_sz);
mdp->rx_skbuff[entry] = skb;
if (skb == NULL)
break; /* Better luck next round. */
skb->dev = ndev;
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ reserve = SH7763_SKB_ALIGN
+ - ((uint32_t)skb->data & (SH7763_SKB_ALIGN-1));
+ if (reserve)
+ skb_reserve(skb, reserve);
+#else
skb_reserve(skb, RX_OFFSET);
+#endif
+ skb->ip_summed = CHECKSUM_NONE;
rxdesc->addr = (u32)skb->data & ~0x3UL;
}
- /* The size of the buffer is 16 byte boundary. */
- rxdesc->buffer_length = (mdp->rx_buf_sz + 16) & ~0x0F;
if (entry >= RX_RING_SIZE - 1)
rxdesc->status |=
- cpu_to_le32(RD_RACT | RD_RFP | RC_RDEL);
+ cpu_to_edmac(mdp, RD_RACT | RD_RFP | RD_RDEL);
else
rxdesc->status |=
- cpu_to_le32(RD_RACT | RD_RFP);
+ cpu_to_edmac(mdp, RD_RACT | RD_RFP);
}
/* Restart Rx engine if stopped. */
/* If we don't need to check status, don't. -KDU */
- ctrl_outl(EDRRR_R, ndev->base_addr + EDRRR);
+ if (!(ctrl_inl(ndev->base_addr + EDRRR) & EDRRR_R))
+ ctrl_outl(EDRRR_R, ndev->base_addr + EDRRR);
return 0;
}
printk(KERN_ERR "Receive Frame Overflow\n");
}
}
-
+#if !defined(CONFIG_CPU_SUBTYPE_SH7763)
if (intr_status & EESR_ADE) {
if (intr_status & EESR_TDE) {
if (intr_status & EESR_TFE)
mdp->stats.tx_fifo_errors++;
}
}
+#endif
if (intr_status & EESR_RDE) {
/* Receive Descriptor Empty int */
mdp->stats.rx_fifo_errors++;
printk(KERN_ERR "Receive FIFO Overflow\n");
}
- if (intr_status &
- (EESR_TWB | EESR_TABT | EESR_ADE | EESR_TDE | EESR_TFE)) {
+ if (intr_status & (EESR_TWB | EESR_TABT |
+#if !defined(CONFIG_CPU_SUBTYPE_SH7763)
+ EESR_ADE |
+#endif
+ EESR_TDE | EESR_TFE)) {
/* Tx error */
u32 edtrr = ctrl_inl(ndev->base_addr + EDTRR);
/* dmesg */
ioaddr = ndev->base_addr;
spin_lock(&mdp->lock);
+ /* Get interrpt stat */
intr_status = ctrl_inl(ioaddr + EESR);
/* Clear interrupt */
ctrl_outl(intr_status, ioaddr + EESR);
- if (intr_status & (EESR_FRC | EESR_RINT8 |
- EESR_RINT5 | EESR_RINT4 | EESR_RINT3 | EESR_RINT2 |
- EESR_RINT1))
+ if (intr_status & (EESR_FRC | /* Frame recv*/
+ EESR_RMAF | /* Multi cast address recv*/
+ EESR_RRF | /* Bit frame recv */
+ EESR_RTLF | /* Long frame recv*/
+ EESR_RTSF | /* short frame recv */
+ EESR_PRE | /* PHY-LSI recv error */
+ EESR_CERF)){ /* recv frame CRC error */
sh_eth_rx(ndev);
- if (intr_status & (EESR_FTC |
- EESR_TINT4 | EESR_TINT3 | EESR_TINT2 | EESR_TINT1)) {
+ }
+ /* Tx Check */
+ if (intr_status & TX_CHECK) {
sh_eth_txfree(ndev);
netif_wake_queue(ndev);
}
if (phydev->duplex != mdp->duplex) {
new_state = 1;
mdp->duplex = phydev->duplex;
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ if (mdp->duplex) { /* FULL */
+ ctrl_outl(ctrl_inl(ioaddr + ECMR) | ECMR_DM,
+ ioaddr + ECMR);
+ } else { /* Half */
+ ctrl_outl(ctrl_inl(ioaddr + ECMR) & ~ECMR_DM,
+ ioaddr + ECMR);
+ }
+#endif
}
if (phydev->speed != mdp->speed) {
new_state = 1;
mdp->speed = phydev->speed;
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ switch (mdp->speed) {
+ case 10: /* 10BASE */
+ ctrl_outl(GECMR_10, ioaddr + GECMR); break;
+ case 100:/* 100BASE */
+ ctrl_outl(GECMR_100, ioaddr + GECMR); break;
+ case 1000: /* 1000BASE */
+ ctrl_outl(GECMR_1000, ioaddr + GECMR); break;
+ default:
+ break;
+ }
+#endif
}
if (mdp->link == PHY_DOWN) {
ctrl_outl((ctrl_inl(ioaddr + ECMR) & ~ECMR_TXF)
/* Set the timer to check for link beat. */
init_timer(&mdp->timer);
mdp->timer.expires = (jiffies + (24 * HZ)) / 10;/* 2.4 sec. */
- setup_timer(&mdp->timer, sh_eth_timer, ndev);
+ setup_timer(&mdp->timer, sh_eth_timer, (unsigned long)ndev);
return ret;
txdesc->buffer_length = skb->len;
if (entry >= TX_RING_SIZE - 1)
- txdesc->status |= cpu_to_le32(TD_TACT | TD_TDLE);
+ txdesc->status |= cpu_to_edmac(mdp, TD_TACT | TD_TDLE);
else
- txdesc->status |= cpu_to_le32(TD_TACT);
+ txdesc->status |= cpu_to_edmac(mdp, TD_TACT);
mdp->cur_tx++;
- ctrl_outl(EDTRR_TRNS, ndev->base_addr + EDTRR);
+ if (!(ctrl_inl(ndev->base_addr + EDTRR) & EDTRR_TRNS))
+ ctrl_outl(EDTRR_TRNS, ndev->base_addr + EDTRR);
+
ndev->trans_start = jiffies;
return 0;
ctrl_outl(0, ioaddr + CDCR); /* (write clear) */
mdp->stats.tx_carrier_errors += ctrl_inl(ioaddr + LCCR);
ctrl_outl(0, ioaddr + LCCR); /* (write clear) */
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ mdp->stats.tx_carrier_errors += ctrl_inl(ioaddr + CERCR);/* CERCR */
+ ctrl_outl(0, ioaddr + CERCR); /* (write clear) */
+ mdp->stats.tx_carrier_errors += ctrl_inl(ioaddr + CEECR);/* CEECR */
+ ctrl_outl(0, ioaddr + CEECR); /* (write clear) */
+#else
mdp->stats.tx_carrier_errors += ctrl_inl(ioaddr + CNDCR);
ctrl_outl(0, ioaddr + CNDCR); /* (write clear) */
-
+#endif
return &mdp->stats;
}
ctrl_outl(0, ioaddr + TSU_FWSL0);
ctrl_outl(0, ioaddr + TSU_FWSL1);
ctrl_outl(TSU_FWSLC_POSTENU | TSU_FWSLC_POSTENL, ioaddr + TSU_FWSLC);
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+ ctrl_outl(0, ioaddr + TSU_QTAG0); /* Disable QTAG(0->1) */
+ ctrl_outl(0, ioaddr + TSU_QTAG1); /* Disable QTAG(1->0) */
+#else
ctrl_outl(0, ioaddr + TSU_QTAGM0); /* Disable QTAG(0->1) */
ctrl_outl(0, ioaddr + TSU_QTAGM1); /* Disable QTAG(1->0) */
+#endif
ctrl_outl(0, ioaddr + TSU_FWSR); /* all interrupt status clear */
ctrl_outl(0, ioaddr + TSU_FWINMK); /* Disable all interrupt */
ctrl_outl(0, ioaddr + TSU_TEN); /* Disable all CAM entry */
struct resource *res;
struct net_device *ndev = NULL;
struct sh_eth_private *mdp;
+ struct sh_eth_plat_data *pd;
/* get base addr */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
mdp = netdev_priv(ndev);
spin_lock_init(&mdp->lock);
+ pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data);
/* get PHY ID */
- mdp->phy_id = (int)pdev->dev.platform_data;
+ mdp->phy_id = pd->phy;
+ /* EDMAC endian */
+ mdp->edmac_endian = pd->edmac_endian;
/* set function */
ndev->open = sh_eth_open;
/* First device only init */
if (!devno) {
+#if defined(ARSTR)
/* reset device */
- ctrl_outl(ARSTR_ARSTR, ndev->base_addr + ARSTR);
+ ctrl_outl(ARSTR_ARSTR, ARSTR);
mdelay(1);
+#endif
+#if defined(SH_TSU_ADDR)
/* TSU init (Init only)*/
sh_eth_tsu_init(SH_TSU_ADDR);
+#endif
}
/* network device register */
ndev->name, CARDNAME, (u32) ndev->base_addr);
for (i = 0; i < 5; i++)
- printk(KERN_INFO "%2.2x:", ndev->dev_addr[i]);
- printk(KERN_INFO "%2.2x, IRQ %d.\n", ndev->dev_addr[i], ndev->irq);
+ printk("%02X:", ndev->dev_addr[i]);
+ printk("%02X, IRQ %d.\n", ndev->dev_addr[i], ndev->irq);
platform_set_drvdata(pdev, ndev);
#include <linux/netdevice.h>
#include <linux/phy.h>
+#include <asm/sh_eth.h>
+
#define CARDNAME "sh-eth"
#define TX_TIMEOUT (5*HZ)
-
-#define TX_RING_SIZE 128 /* Tx ring size */
-#define RX_RING_SIZE 128 /* Rx ring size */
-#define RX_OFFSET 2 /* skb offset */
+#define TX_RING_SIZE 64 /* Tx ring size */
+#define RX_RING_SIZE 64 /* Rx ring size */
#define ETHERSMALL 60
#define PKT_BUF_SZ 1538
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+
+#define SH7763_SKB_ALIGN 32
/* Chip Base Address */
-#define SH_TSU_ADDR 0xA7000804
+# define SH_TSU_ADDR 0xFFE01800
+# define ARSTR 0xFFE01800
/* Chip Registers */
/* E-DMAC */
-#define EDMR 0x0000
-#define EDTRR 0x0004
-#define EDRRR 0x0008
-#define TDLAR 0x000C
-#define RDLAR 0x0010
-#define EESR 0x0014
-#define EESIPR 0x0018
-#define TRSCER 0x001C
-#define RMFCR 0x0020
-#define TFTR 0x0024
-#define FDR 0x0028
-#define RMCR 0x002C
-#define EDOCR 0x0030
-#define FCFTR 0x0034
-#define RPADIR 0x0038
-#define TRIMD 0x003C
-#define RBWAR 0x0040
-#define RDFAR 0x0044
-#define TBRAR 0x004C
-#define TDFAR 0x0050
+# define EDSR 0x000
+# define EDMR 0x400
+# define EDTRR 0x408
+# define EDRRR 0x410
+# define EESR 0x428
+# define EESIPR 0x430
+# define TDLAR 0x010
+# define TDFAR 0x014
+# define TDFXR 0x018
+# define TDFFR 0x01C
+# define RDLAR 0x030
+# define RDFAR 0x034
+# define RDFXR 0x038
+# define RDFFR 0x03C
+# define TRSCER 0x438
+# define RMFCR 0x440
+# define TFTR 0x448
+# define FDR 0x450
+# define RMCR 0x458
+# define RPADIR 0x460
+# define FCFTR 0x468
+
+/* Ether Register */
+# define ECMR 0x500
+# define ECSR 0x510
+# define ECSIPR 0x518
+# define PIR 0x520
+# define PSR 0x528
+# define PIPR 0x52C
+# define RFLR 0x508
+# define APR 0x554
+# define MPR 0x558
+# define PFTCR 0x55C
+# define PFRCR 0x560
+# define TPAUSER 0x564
+# define GECMR 0x5B0
+# define BCULR 0x5B4
+# define MAHR 0x5C0
+# define MALR 0x5C8
+# define TROCR 0x700
+# define CDCR 0x708
+# define LCCR 0x710
+# define CEFCR 0x740
+# define FRECR 0x748
+# define TSFRCR 0x750
+# define TLFRCR 0x758
+# define RFCR 0x760
+# define CERCR 0x768
+# define CEECR 0x770
+# define MAFCR 0x778
+
+/* TSU Absolute Address */
+# define TSU_CTRST 0x004
+# define TSU_FWEN0 0x010
+# define TSU_FWEN1 0x014
+# define TSU_FCM 0x18
+# define TSU_BSYSL0 0x20
+# define TSU_BSYSL1 0x24
+# define TSU_PRISL0 0x28
+# define TSU_PRISL1 0x2C
+# define TSU_FWSL0 0x30
+# define TSU_FWSL1 0x34
+# define TSU_FWSLC 0x38
+# define TSU_QTAG0 0x40
+# define TSU_QTAG1 0x44
+# define TSU_FWSR 0x50
+# define TSU_FWINMK 0x54
+# define TSU_ADQT0 0x48
+# define TSU_ADQT1 0x4C
+# define TSU_VTAG0 0x58
+# define TSU_VTAG1 0x5C
+# define TSU_ADSBSY 0x60
+# define TSU_TEN 0x64
+# define TSU_POST1 0x70
+# define TSU_POST2 0x74
+# define TSU_POST3 0x78
+# define TSU_POST4 0x7C
+# define TSU_ADRH0 0x100
+# define TSU_ADRL0 0x104
+# define TSU_ADRH31 0x1F8
+# define TSU_ADRL31 0x1FC
+
+# define TXNLCR0 0x80
+# define TXALCR0 0x84
+# define RXNLCR0 0x88
+# define RXALCR0 0x8C
+# define FWNLCR0 0x90
+# define FWALCR0 0x94
+# define TXNLCR1 0xA0
+# define TXALCR1 0xA4
+# define RXNLCR1 0xA8
+# define RXALCR1 0xAC
+# define FWNLCR1 0xB0
+# define FWALCR1 0x40
+
+#else /* CONFIG_CPU_SUBTYPE_SH7763 */
+# define RX_OFFSET 2 /* skb offset */
+#ifndef CONFIG_CPU_SUBTYPE_SH7619
+/* Chip base address */
+# define SH_TSU_ADDR 0xA7000804
+# define ARSTR 0xA7000800
+#endif
+/* Chip Registers */
+/* E-DMAC */
+# define EDMR 0x0000
+# define EDTRR 0x0004
+# define EDRRR 0x0008
+# define TDLAR 0x000C
+# define RDLAR 0x0010
+# define EESR 0x0014
+# define EESIPR 0x0018
+# define TRSCER 0x001C
+# define RMFCR 0x0020
+# define TFTR 0x0024
+# define FDR 0x0028
+# define RMCR 0x002C
+# define EDOCR 0x0030
+# define FCFTR 0x0034
+# define RPADIR 0x0038
+# define TRIMD 0x003C
+# define RBWAR 0x0040
+# define RDFAR 0x0044
+# define TBRAR 0x004C
+# define TDFAR 0x0050
+
/* Ether Register */
-#define ECMR 0x0160
-#define ECSR 0x0164
-#define ECSIPR 0x0168
-#define PIR 0x016C
-#define MAHR 0x0170
-#define MALR 0x0174
-#define RFLR 0x0178
-#define PSR 0x017C
-#define TROCR 0x0180
-#define CDCR 0x0184
-#define LCCR 0x0188
-#define CNDCR 0x018C
-#define CEFCR 0x0194
-#define FRECR 0x0198
-#define TSFRCR 0x019C
-#define TLFRCR 0x01A0
-#define RFCR 0x01A4
-#define MAFCR 0x01A8
-#define IPGR 0x01B4
-#if defined(CONFIG_CPU_SUBTYPE_SH7710)
-#define APR 0x01B8
-#define MPR 0x01BC
-#define TPAUSER 0x1C4
-#define BCFR 0x1CC
-#endif /* CONFIG_CPU_SH7710 */
-
-#define ARSTR 0x0800
+# define ECMR 0x0160
+# define ECSR 0x0164
+# define ECSIPR 0x0168
+# define PIR 0x016C
+# define MAHR 0x0170
+# define MALR 0x0174
+# define RFLR 0x0178
+# define PSR 0x017C
+# define TROCR 0x0180
+# define CDCR 0x0184
+# define LCCR 0x0188
+# define CNDCR 0x018C
+# define CEFCR 0x0194
+# define FRECR 0x0198
+# define TSFRCR 0x019C
+# define TLFRCR 0x01A0
+# define RFCR 0x01A4
+# define MAFCR 0x01A8
+# define IPGR 0x01B4
+# if defined(CONFIG_CPU_SUBTYPE_SH7710)
+# define APR 0x01B8
+# define MPR 0x01BC
+# define TPAUSER 0x1C4
+# define BCFR 0x1CC
+# endif /* CONFIG_CPU_SH7710 */
/* TSU */
-#define TSU_CTRST 0x004
-#define TSU_FWEN0 0x010
-#define TSU_FWEN1 0x014
-#define TSU_FCM 0x018
-#define TSU_BSYSL0 0x020
-#define TSU_BSYSL1 0x024
-#define TSU_PRISL0 0x028
-#define TSU_PRISL1 0x02C
-#define TSU_FWSL0 0x030
-#define TSU_FWSL1 0x034
-#define TSU_FWSLC 0x038
-#define TSU_QTAGM0 0x040
-#define TSU_QTAGM1 0x044
-#define TSU_ADQT0 0x048
-#define TSU_ADQT1 0x04C
-#define TSU_FWSR 0x050
-#define TSU_FWINMK 0x054
-#define TSU_ADSBSY 0x060
-#define TSU_TEN 0x064
-#define TSU_POST1 0x070
-#define TSU_POST2 0x074
-#define TSU_POST3 0x078
-#define TSU_POST4 0x07C
-#define TXNLCR0 0x080
-#define TXALCR0 0x084
-#define RXNLCR0 0x088
-#define RXALCR0 0x08C
-#define FWNLCR0 0x090
-#define FWALCR0 0x094
-#define TXNLCR1 0x0A0
-#define TXALCR1 0x0A4
-#define RXNLCR1 0x0A8
-#define RXALCR1 0x0AC
-#define FWNLCR1 0x0B0
-#define FWALCR1 0x0B4
+# define TSU_CTRST 0x004
+# define TSU_FWEN0 0x010
+# define TSU_FWEN1 0x014
+# define TSU_FCM 0x018
+# define TSU_BSYSL0 0x020
+# define TSU_BSYSL1 0x024
+# define TSU_PRISL0 0x028
+# define TSU_PRISL1 0x02C
+# define TSU_FWSL0 0x030
+# define TSU_FWSL1 0x034
+# define TSU_FWSLC 0x038
+# define TSU_QTAGM0 0x040
+# define TSU_QTAGM1 0x044
+# define TSU_ADQT0 0x048
+# define TSU_ADQT1 0x04C
+# define TSU_FWSR 0x050
+# define TSU_FWINMK 0x054
+# define TSU_ADSBSY 0x060
+# define TSU_TEN 0x064
+# define TSU_POST1 0x070
+# define TSU_POST2 0x074
+# define TSU_POST3 0x078
+# define TSU_POST4 0x07C
+# define TXNLCR0 0x080
+# define TXALCR0 0x084
+# define RXNLCR0 0x088
+# define RXALCR0 0x08C
+# define FWNLCR0 0x090
+# define FWALCR0 0x094
+# define TXNLCR1 0x0A0
+# define TXALCR1 0x0A4
+# define RXNLCR1 0x0A8
+# define RXALCR1 0x0AC
+# define FWNLCR1 0x0B0
+# define FWALCR1 0x0B4
#define TSU_ADRH0 0x0100
#define TSU_ADRL0 0x0104
#define TSU_ADRL31 0x01FC
-/* Register's bits */
+#endif /* CONFIG_CPU_SUBTYPE_SH7763 */
+
+/*
+ * Register's bits
+ */
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+/* EDSR */
+enum EDSR_BIT {
+ EDSR_ENT = 0x01, EDSR_ENR = 0x02,
+};
+#define EDSR_ENALL (EDSR_ENT|EDSR_ENR)
+
+/* GECMR */
+enum GECMR_BIT {
+ GECMR_10 = 0x0, GECMR_100 = 0x04, GECMR_1000 = 0x01,
+};
+#endif
/* EDMR */
enum DMAC_M_BIT {
- EDMR_DL1 = 0x20, EDMR_DL0 = 0x10, EDMR_SRST = 0x01,
+ EDMR_DL1 = 0x20, EDMR_DL0 = 0x10,
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+ EDMR_SRST = 0x03,
+ EMDR_DESC_R = 0x30, /* Descriptor reserve size */
+ EDMR_EL = 0x40, /* Litte endian */
+#else /* CONFIG_CPU_SUBTYPE_SH7763 */
+ EDMR_SRST = 0x01,
+#endif
};
/* EDTRR */
enum DMAC_T_BIT {
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+ EDTRR_TRNS = 0x03,
+#else
EDTRR_TRNS = 0x01,
+#endif
};
/* EDRRR*/
/* EESR */
enum EESR_BIT {
- EESR_TWB = 0x40000000, EESR_TABT = 0x04000000,
+#ifndef CONFIG_CPU_SUBTYPE_SH7763
+ EESR_TWB = 0x40000000,
+#else
+ EESR_TWB = 0xC0000000,
+ EESR_TC1 = 0x20000000,
+ EESR_TUC = 0x10000000,
+ EESR_ROC = 0x80000000,
+#endif
+ EESR_TABT = 0x04000000,
EESR_RABT = 0x02000000, EESR_RFRMER = 0x01000000,
- EESR_ADE = 0x00800000, EESR_ECI = 0x00400000,
- EESR_FTC = 0x00200000, EESR_TDE = 0x00100000,
- EESR_TFE = 0x00080000, EESR_FRC = 0x00040000,
- EESR_RDE = 0x00020000, EESR_RFE = 0x00010000,
- EESR_TINT4 = 0x00000800, EESR_TINT3 = 0x00000400,
- EESR_TINT2 = 0x00000200, EESR_TINT1 = 0x00000100,
- EESR_RINT8 = 0x00000080, EESR_RINT5 = 0x00000010,
- EESR_RINT4 = 0x00000008, EESR_RINT3 = 0x00000004,
- EESR_RINT2 = 0x00000002, EESR_RINT1 = 0x00000001,
-};
-
-#define EESR_ERR_CHECK (EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE \
+#ifndef CONFIG_CPU_SUBTYPE_SH7763
+ EESR_ADE = 0x00800000,
+#endif
+ EESR_ECI = 0x00400000,
+ EESR_FTC = 0x00200000, EESR_TDE = 0x00100000,
+ EESR_TFE = 0x00080000, EESR_FRC = 0x00040000,
+ EESR_RDE = 0x00020000, EESR_RFE = 0x00010000,
+#ifndef CONFIG_CPU_SUBTYPE_SH7763
+ EESR_CND = 0x00000800,
+#endif
+ EESR_DLC = 0x00000400,
+ EESR_CD = 0x00000200, EESR_RTO = 0x00000100,
+ EESR_RMAF = 0x00000080, EESR_CEEF = 0x00000040,
+ EESR_CELF = 0x00000020, EESR_RRF = 0x00000010,
+ EESR_RTLF = 0x00000008, EESR_RTSF = 0x00000004,
+ EESR_PRE = 0x00000002, EESR_CERF = 0x00000001,
+};
+
+
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+# define TX_CHECK (EESR_TC1 | EESR_FTC)
+# define EESR_ERR_CHECK (EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE \
+ | EESR_RFRMER | EESR_TFE | EESR_TDE | EESR_ECI)
+# define TX_ERROR_CEHCK (EESR_TWB | EESR_TABT | EESR_TDE | EESR_TFE)
+
+#else
+# define TX_CHECK (EESR_FTC | EESR_CND | EESR_DLC | EESR_CD | EESR_RTO)
+# define EESR_ERR_CHECK (EESR_TWB | EESR_TABT | EESR_RABT | EESR_RDE \
| EESR_RFRMER | EESR_ADE | EESR_TFE | EESR_TDE | EESR_ECI)
+# define TX_ERROR_CEHCK (EESR_TWB | EESR_TABT | EESR_ADE | EESR_TDE | EESR_TFE)
+#endif
/* EESIPR */
enum DMAC_IM_BIT {
/* Receive descriptor bit */
enum RD_STS_BIT {
- RD_RACT = 0x80000000, RC_RDEL = 0x40000000,
- RC_RFP1 = 0x20000000, RC_RFP0 = 0x10000000,
+ RD_RACT = 0x80000000, RD_RDEL = 0x40000000,
+ RD_RFP1 = 0x20000000, RD_RFP0 = 0x10000000,
RD_RFE = 0x08000000, RD_RFS10 = 0x00000200,
RD_RFS9 = 0x00000100, RD_RFS8 = 0x00000080,
RD_RFS7 = 0x00000040, RD_RFS6 = 0x00000020,
RD_RFS3 = 0x00000004, RD_RFS2 = 0x00000002,
RD_RFS1 = 0x00000001,
};
-#define RDF1ST RC_RFP1
-#define RDFEND RC_RFP0
-#define RD_RFP (RC_RFP1|RC_RFP0)
+#define RDF1ST RD_RFP1
+#define RDFEND RD_RFP0
+#define RD_RFP (RD_RFP1|RD_RFP0)
/* FCFTR */
enum FCFTR_BIT {
FCFTR_RFD1 = 0x00000002, FCFTR_RFD0 = 0x00000001,
};
#define FIFO_F_D_RFF (FCFTR_RFF2|FCFTR_RFF1|FCFTR_RFF0)
+#ifndef CONFIG_CPU_SUBTYPE_SH7619
#define FIFO_F_D_RFD (FCFTR_RFD2|FCFTR_RFD1|FCFTR_RFD0)
+#else
+#define FIFO_F_D_RFD (FCFTR_RFD0)
+#endif
/* Transfer descriptor bit */
enum TD_STS_BIT {
- TD_TACT = 0x80000000, TD_TDLE = 0x40000000, TD_TFP1 = 0x20000000,
+ TD_TACT = 0x80000000,
+ TD_TDLE = 0x40000000, TD_TFP1 = 0x20000000,
TD_TFP0 = 0x10000000,
};
#define TDF1ST TD_TFP1
enum RECV_RST_BIT { RMCR_RST = 0x01, };
/* ECMR */
enum FELIC_MODE_BIT {
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+ ECMR_TRCCM = 0x04000000, ECMR_RCSC = 0x00800000,
+ ECMR_DPAD = 0x00200000, ECMR_RZPF = 0x00100000,
+#endif
ECMR_ZPF = 0x00080000, ECMR_PFR = 0x00040000, ECMR_RXF = 0x00020000,
ECMR_TXF = 0x00010000, ECMR_MCT = 0x00002000, ECMR_PRCEF = 0x00001000,
ECMR_PMDE = 0x00000200, ECMR_RE = 0x00000040, ECMR_TE = 0x00000020,
ECMR_PRM = 0x00000001,
};
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+#define ECMR_CHG_DM (ECMR_TRCCM | ECMR_RZPF | ECMR_ZPF |\
+ ECMR_PFR | ECMR_RXF | ECMR_TXF | ECMR_MCT)
+#elif CONFIG_CPU_SUBTYPE_SH7619
+#define ECMR_CHG_DM (ECMR_ZPF | ECMR_PFR | ECMR_RXF | ECMR_TXF)
+#else
+#define ECMR_CHG_DM (ECMR_ZPF | ECMR_PFR | ECMR_RXF | ECMR_TXF | ECMR_MCT)
+#endif
+
/* ECSR */
enum ECSR_STATUS_BIT {
- ECSR_BRCRX = 0x20, ECSR_PSRTO = 0x10, ECSR_LCHNG = 0x04,
+#ifndef CONFIG_CPU_SUBTYPE_SH7763
+ ECSR_BRCRX = 0x20, ECSR_PSRTO = 0x10,
+#endif
+ ECSR_LCHNG = 0x04,
ECSR_MPD = 0x02, ECSR_ICD = 0x01,
};
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+# define ECSR_INIT (ECSR_ICD | ECSIPR_MPDIP)
+#else
+# define ECSR_INIT (ECSR_BRCRX | ECSR_PSRTO | \
+ ECSR_LCHNG | ECSR_ICD | ECSIPR_MPDIP)
+#endif
+
/* ECSIPR */
enum ECSIPR_STATUS_MASK_BIT {
- ECSIPR_BRCRXIP = 0x20, ECSIPR_PSRTOIP = 0x10, ECSIPR_LCHNGIP = 0x04,
+#ifndef CONFIG_CPU_SUBTYPE_SH7763
+ ECSIPR_BRCRXIP = 0x20, ECSIPR_PSRTOIP = 0x10,
+#endif
+ ECSIPR_LCHNGIP = 0x04,
ECSIPR_MPDIP = 0x02, ECSIPR_ICDIP = 0x01,
};
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+# define ECSIPR_INIT (ECSIPR_LCHNGIP | ECSIPR_ICDIP | ECSIPR_MPDIP)
+#else
+# define ECSIPR_INIT (ECSIPR_BRCRXIP | ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | \
+ ECSIPR_ICDIP | ECSIPR_MPDIP)
+#endif
+
/* APR */
enum APR_BIT {
APR_AP = 0x00000001,
RPADIR_PADR = 0x0003f,
};
+#if defined(CONFIG_CPU_SUBTYPE_SH7763)
+# define RPADIR_INIT (0x00)
+#else
+# define RPADIR_INIT (RPADIR_PADS1)
+#endif
+
+/* RFLR */
+#define RFLR_VALUE 0x1000
+
/* FDR */
enum FIFO_SIZE_BIT {
+#ifndef CONFIG_CPU_SUBTYPE_SH7619
FIFO_SIZE_T = 0x00000700, FIFO_SIZE_R = 0x00000007,
+#else
+ FIFO_SIZE_T = 0x00000100, FIFO_SIZE_R = 0x00000001,
+#endif
};
enum phy_offsets {
PHY_CTRL = 0, PHY_STAT = 1, PHY_IDT1 = 2, PHY_IDT2 = 3,
PHY_A_NP = 0x8000, PHY_A_ACK = 0x4000, PHY_A_RF = 0x2000,
PHY_A_FCS = 0x0400, PHY_A_T4 = 0x0200, PHY_A_FDX = 0x0100,
PHY_A_HDX = 0x0080, PHY_A_10FDX = 0x0040, PHY_A_10HDX = 0x0020,
- PHY_A_SEL = 0x001f,
+ PHY_A_SEL = 0x001e,
};
/* PHY_ANL */
enum PHY_ANL_BIT {
#endif
u32 addr; /* TD2 */
u32 pad1; /* padding data */
-};
+} __attribute__((aligned(2), packed));
/*
* The sh ether Rx buffer descriptors.
#endif
u32 addr; /* RD2 */
u32 pad0; /* padding data */
-};
+} __attribute__((aligned(2), packed));
struct sh_eth_private {
dma_addr_t rx_desc_dma;
u32 cur_rx, dirty_rx; /* Producer/consumer ring indices */
u32 cur_tx, dirty_tx;
u32 rx_buf_sz; /* Based on MTU+slack. */
+ int edmac_endian;
/* MII transceiver section. */
u32 phy_id; /* PHY ID */
struct mii_bus *mii_bus; /* MDIO bus control */
struct net_device_stats tsu_stats; /* TSU forward status */
};
+#ifdef CONFIG_CPU_SUBTYPE_SH7763
+/* SH7763 has endian control register */
+#define swaps(x, y)
+#else
static void swaps(char *src, int len)
{
#ifdef __LITTLE_ENDIAN__
*p = swab32(*p);
#endif
}
-
+#endif /* CONFIG_CPU_SUBTYPE_SH7763 */
#endif
#include "h/smc.h"
#include "h/smt_p.h"
#include <linux/bitrev.h>
+#include <linux/kernel.h>
#define KERNEL
#include "h/smtstate.h"
#endif
#ifdef DEBUG
-#define hextoasc(x) "0123456789abcdef"[x]
-
char *addr_to_string(struct fddi_addr *addr)
{
int i ;
static char string[6*3] = "****" ;
for (i = 0 ; i < 6 ; i++) {
- string[i*3] = hextoasc((addr->a[i]>>4)&0xf) ;
- string[i*3+1] = hextoasc((addr->a[i])&0xf) ;
- string[i*3+2] = ':' ;
+ string[i * 3] = hex_asc_hi(addr->a[i]);
+ string[i * 3 + 1] = hex_asc_lo(addr->a[i]);
+ string[i * 3 + 2] = ':';
}
- string[5*3+2] = 0 ;
- return(string) ;
+ string[5 * 3 + 2] = 0;
+ return(string);
}
#endif
PC_VAUX_ON | PC_VCC_OFF));
}
-static void sky2_power_state(struct sky2_hw *hw, pci_power_t state)
-{
- u16 power_control = sky2_pci_read16(hw, hw->pm_cap + PCI_PM_CTRL);
- int pex = pci_find_capability(hw->pdev, PCI_CAP_ID_EXP);
- u32 reg;
-
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-
- switch (state) {
- case PCI_D0:
- break;
-
- case PCI_D1:
- power_control |= 1;
- break;
-
- case PCI_D2:
- power_control |= 2;
- break;
-
- case PCI_D3hot:
- case PCI_D3cold:
- power_control |= 3;
- if (hw->flags & SKY2_HW_ADV_POWER_CTL) {
- /* additional power saving measurements */
- reg = sky2_pci_read32(hw, PCI_DEV_REG4);
-
- /* set gating core clock for LTSSM in L1 state */
- reg |= P_PEX_LTSSM_STAT(P_PEX_LTSSM_L1_STAT) |
- /* auto clock gated scheme controlled by CLKREQ */
- P_ASPM_A1_MODE_SELECT |
- /* enable Gate Root Core Clock */
- P_CLK_GATE_ROOT_COR_ENA;
-
- if (pex && (hw->flags & SKY2_HW_CLK_POWER)) {
- /* enable Clock Power Management (CLKREQ) */
- u16 ctrl = sky2_pci_read16(hw, pex + PCI_EXP_DEVCTL);
-
- ctrl |= PCI_EXP_DEVCTL_AUX_PME;
- sky2_pci_write16(hw, pex + PCI_EXP_DEVCTL, ctrl);
- } else
- /* force CLKREQ Enable in Our4 (A1b only) */
- reg |= P_ASPM_FORCE_CLKREQ_ENA;
-
- /* set Mask Register for Release/Gate Clock */
- sky2_pci_write32(hw, PCI_DEV_REG5,
- P_REL_PCIE_EXIT_L1_ST | P_GAT_PCIE_ENTER_L1_ST |
- P_REL_PCIE_RX_EX_IDLE | P_GAT_PCIE_RX_EL_IDLE |
- P_REL_GPHY_LINK_UP | P_GAT_GPHY_LINK_DOWN);
- } else
- sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_CLK_HALT);
-
- /* put CPU into reset state */
- sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_RESET);
- if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev == CHIP_REV_YU_SU_A0)
- /* put CPU into halt state */
- sky2_write8(hw, B28_Y2_ASF_STAT_CMD, HCU_CCSR_ASF_HALTED);
-
- if (pex && !(hw->flags & SKY2_HW_RAM_BUFFER)) {
- reg = sky2_pci_read32(hw, PCI_DEV_REG1);
- /* force to PCIe L1 */
- reg |= PCI_FORCE_PEX_L1;
- sky2_pci_write32(hw, PCI_DEV_REG1, reg);
- }
- break;
-
- default:
- dev_warn(&hw->pdev->dev, PFX "Invalid power state (%d) ",
- state);
- return;
- }
-
- power_control |= PCI_PM_CTRL_PME_ENABLE;
- /* Finally, set the new power state. */
- sky2_pci_write32(hw, hw->pm_cap + PCI_PM_CTRL, power_control);
-
- sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
- sky2_pci_read32(hw, B0_CTST);
-}
-
static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
sky2_pci_read32(hw, PCI_DEV_REG1);
+
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_ANE);
+ else if (hw->flags & SKY2_HW_ADV_POWER_CTL)
+ sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
}
static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
hw->flags = SKY2_HW_GIGABIT
| SKY2_HW_NEWER_PHY
| SKY2_HW_ADV_POWER_CTL;
-
- /* check for Rev. A1 dev 4200 */
- if (sky2_read16(hw, Q_ADDR(Q_XA1, Q_WM)) == 0)
- hw->flags |= SKY2_HW_CLK_POWER;
break;
case CHIP_ID_YUKON_EX:
if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P')
hw->flags |= SKY2_HW_FIBRE_PHY;
- hw->pm_cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PM);
- if (hw->pm_cap == 0) {
- dev_err(&hw->pdev->dev, "cannot find PowerManagement capability\n");
- return -EIO;
- }
-
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
pci_save_state(pdev);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
- sky2_power_state(hw, pci_choose_state(pdev, state));
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
return 0;
}
if (!hw)
return 0;
- sky2_power_state(hw, PCI_D0);
+ err = pci_set_power_state(pdev, PCI_D0);
+ if (err)
+ goto out;
err = pci_restore_state(pdev);
if (err)
pci_enable_wake(pdev, PCI_D3cold, wol);
pci_disable_device(pdev);
- sky2_power_state(hw, PCI_D3hot);
+ pci_set_power_state(pdev, PCI_D3hot);
}
static struct pci_driver sky2_driver = {
#define SKY2_HW_NEW_LE 0x00000020 /* new LSOv2 format */
#define SKY2_HW_AUTO_TX_SUM 0x00000040 /* new IP decode for Tx */
#define SKY2_HW_ADV_POWER_CTL 0x00000080 /* additional PHY power regs */
-#define SKY2_HW_CLK_POWER 0x00000100 /* clock power management */
- int pm_cap;
u8 chip_id;
u8 chip_rev;
u8 pmd_type;
*/
#include <linux/dma-mapping.h>
#include <asm/dma.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
static dma_addr_t rx_dmabuf, tx_dmabuf;
static int rx_dmalen, tx_dmalen;
#elif defined(CONFIG_SA1100_ASSABET)
-#include <asm/arch/neponset.h>
+#include <mach/neponset.h>
/* We can only do 8-bit reads and writes in the static memory space. */
#define SMC_CAN_USE_8BIT 1
* IOBARRIER on entry to their ISR.
*/
-#include <asm/arch/constants.h> /* IOBARRIER_VIRT */
+#include <mach/constants.h> /* IOBARRIER_VIRT */
#define SMC_CAN_USE_8BIT 0
#define SMC_CAN_USE_16BIT 1
*/
#include <linux/dma-mapping.h>
#include <asm/dma.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#ifdef SMC_insl
#undef SMC_insl
#include <asm/system.h>
#include <asm/io.h>
-#include <asm/se.h>
+#include <mach-se/mach/se.h>
#include <asm/machvec.h>
#ifdef CONFIG_SH_STANDARD_BIOS
#include <asm/sh_bios.h>
int len = ((char *) p->iscp - (char *) ptr - 8) / 6;
if(num_addrs > len) {
printk("%s: switching to promisc. mode\n",dev->name);
- dev->flags|=IFF_PROMISC;
+ cfg_cmd->promisc = 1;
}
}
if(dev->flags&IFF_PROMISC)
- {
- cfg_cmd->promisc=1;
- dev->flags|=IFF_PROMISC;
- }
+ cfg_cmd->promisc = 1;
cfg_cmd->carr_coll = 0x00;
p->scb->cbl_offset = make16(cfg_cmd);
static int tg3_set_power_state(struct tg3 *tp, pci_power_t state)
{
u32 misc_host_ctrl;
- u16 power_control, power_caps;
- int pm = tp->pm_cap;
/* Make sure register accesses (indirect or otherwise)
* will function correctly.
TG3PCI_MISC_HOST_CTRL,
tp->misc_host_ctrl);
- pci_read_config_word(tp->pdev,
- pm + PCI_PM_CTRL,
- &power_control);
- power_control |= PCI_PM_CTRL_PME_STATUS;
- power_control &= ~(PCI_PM_CTRL_STATE_MASK);
switch (state) {
case PCI_D0:
- power_control |= 0;
- pci_write_config_word(tp->pdev,
- pm + PCI_PM_CTRL,
- power_control);
- udelay(100); /* Delay after power state change */
+ pci_enable_wake(tp->pdev, state, false);
+ pci_set_power_state(tp->pdev, PCI_D0);
/* Switch out of Vaux if it is a NIC */
if (tp->tg3_flags2 & TG3_FLG2_IS_NIC)
return 0;
case PCI_D1:
- power_control |= 1;
- break;
-
case PCI_D2:
- power_control |= 2;
- break;
-
case PCI_D3hot:
- power_control |= 3;
break;
default:
- printk(KERN_WARNING PFX "%s: Invalid power state (%d) "
- "requested.\n",
- tp->dev->name, state);
+ printk(KERN_ERR PFX "%s: Invalid power state (D%d) requested\n",
+ tp->dev->name, state);
return -EINVAL;
}
-
- power_control |= PCI_PM_CTRL_PME_ENABLE;
-
misc_host_ctrl = tr32(TG3PCI_MISC_HOST_CTRL);
tw32(TG3PCI_MISC_HOST_CTRL,
misc_host_ctrl | MISC_HOST_CTRL_MASK_PCI_INT);
WOL_DRV_WOL |
WOL_SET_MAGIC_PKT);
- pci_read_config_word(tp->pdev, pm + PCI_PM_PMC, &power_caps);
-
if (tp->tg3_flags & TG3_FLAG_WOL_ENABLE) {
u32 mac_mode;
if (!(tp->tg3_flags2 & TG3_FLG2_5750_PLUS))
tw32(MAC_LED_CTRL, tp->led_ctrl);
- if (((power_caps & PCI_PM_CAP_PME_D3cold) &&
- (tp->tg3_flags & TG3_FLAG_WOL_ENABLE)))
+ if (pci_pme_capable(tp->pdev, state) &&
+ (tp->tg3_flags & TG3_FLAG_WOL_ENABLE))
mac_mode |= MAC_MODE_MAGIC_PKT_ENABLE;
tw32_f(MAC_MODE, mac_mode);
tg3_write_sig_post_reset(tp, RESET_KIND_SHUTDOWN);
+ if (tp->tg3_flags & TG3_FLAG_WOL_ENABLE)
+ pci_enable_wake(tp->pdev, state, true);
+
/* Finally, set the new power state. */
- pci_write_config_word(tp->pdev, pm + PCI_PM_CTRL, power_control);
- udelay(100); /* Delay after power state change */
+ pci_set_power_state(tp->pdev, state);
return 0;
}
*/
static int tg3_init_hw(struct tg3 *tp, int reset_phy)
{
- int err;
-
- /* Force the chip into D0. */
- err = tg3_set_power_state(tp, PCI_D0);
- if (err)
- goto out;
-
tg3_switch_clocks(tp);
tw32(TG3PCI_MEM_WIN_BASE_ADDR, 0);
- err = tg3_reset_hw(tp, reset_phy);
-
-out:
- return err;
+ return tg3_reset_hw(tp, reset_phy);
}
#define TG3_STAT_ADD32(PSTAT, REG) \
netif_carrier_off(tp->dev);
- tg3_full_lock(tp, 0);
-
err = tg3_set_power_state(tp, PCI_D0);
- if (err) {
- tg3_full_unlock(tp);
+ if (err)
return err;
- }
+
+ tg3_full_lock(tp, 0);
tg3_disable_ints(tp);
tp->tg3_flags &= ~TG3_FLAG_INIT_COMPLETE;
{
struct tg3 *tp = netdev_priv(dev);
- if (tp->tg3_flags & TG3_FLAG_WOL_CAP)
+ if ((tp->tg3_flags & TG3_FLAG_WOL_CAP) &&
+ device_can_wakeup(&tp->pdev->dev))
wol->supported = WAKE_MAGIC;
else
wol->supported = 0;
static int tg3_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct tg3 *tp = netdev_priv(dev);
+ struct device *dp = &tp->pdev->dev;
if (wol->wolopts & ~WAKE_MAGIC)
return -EINVAL;
if ((wol->wolopts & WAKE_MAGIC) &&
- !(tp->tg3_flags & TG3_FLAG_WOL_CAP))
+ !((tp->tg3_flags & TG3_FLAG_WOL_CAP) && device_can_wakeup(dp)))
return -EINVAL;
spin_lock_bh(&tp->lock);
- if (wol->wolopts & WAKE_MAGIC)
+ if (wol->wolopts & WAKE_MAGIC) {
tp->tg3_flags |= TG3_FLAG_WOL_ENABLE;
- else
+ device_set_wakeup_enable(dp, true);
+ } else {
tp->tg3_flags &= ~TG3_FLAG_WOL_ENABLE;
+ device_set_wakeup_enable(dp, false);
+ }
spin_unlock_bh(&tp->lock);
return 0;
if (val & VCPU_CFGSHDW_ASPM_DBNC)
tp->tg3_flags |= TG3_FLAG_ASPM_WORKAROUND;
if ((val & VCPU_CFGSHDW_WOL_ENABLE) &&
- (val & VCPU_CFGSHDW_WOL_MAGPKT))
+ (val & VCPU_CFGSHDW_WOL_MAGPKT) &&
+ device_may_wakeup(&tp->pdev->dev))
tp->tg3_flags |= TG3_FLAG_WOL_ENABLE;
return;
}
!(nic_cfg & NIC_SRAM_DATA_CFG_FIBER_WOL))
tp->tg3_flags &= ~TG3_FLAG_WOL_CAP;
- if (tp->tg3_flags & TG3_FLAG_WOL_CAP &&
- nic_cfg & NIC_SRAM_DATA_CFG_WOL_ENABLE)
+ if ((tp->tg3_flags & TG3_FLAG_WOL_CAP) &&
+ (nic_cfg & NIC_SRAM_DATA_CFG_WOL_ENABLE) &&
+ device_may_wakeup(&tp->pdev->dev))
tp->tg3_flags |= TG3_FLAG_WOL_ENABLE;
if (cfg2 & (1 << 17))
{
struct net_device *dev = pci_get_drvdata(pdev);
struct tg3 *tp = netdev_priv(dev);
+ pci_power_t target_state;
int err;
/* PCI register 4 needs to be saved whether netif_running() or not.
tp->tg3_flags &= ~TG3_FLAG_INIT_COMPLETE;
tg3_full_unlock(tp);
- err = tg3_set_power_state(tp, pci_choose_state(pdev, state));
+ target_state = pdev->pm_cap ? pci_target_state(pdev) : PCI_D3hot;
+
+ err = tg3_set_power_state(tp, target_state);
if (err) {
int err2;
static int ringspeed[XL_MAX_ADAPTERS] = {0,} ;
module_param_array(ringspeed, int, NULL, 0);
-MODULE_PARM_DESC(ringspeed,"3c359: Ringspeed selection - 4,16 or 0") ;
+MODULE_PARM_DESC(ringspeed,"3c359: Ringspeed selection - 4,16 or 0") ;
/* Packet buffer size */
static int pkt_buf_sz[XL_MAX_ADAPTERS] = {0,} ;
module_param_array(pkt_buf_sz, int, NULL, 0) ;
-MODULE_PARM_DESC(pkt_buf_sz,"3c359: Initial buffer size") ;
+MODULE_PARM_DESC(pkt_buf_sz,"3c359: Initial buffer size") ;
/* Message Level */
-static int message_level[XL_MAX_ADAPTERS] = {0,} ;
+static int message_level[XL_MAX_ADAPTERS] = {0,} ;
module_param_array(message_level, int, NULL, 0) ;
-MODULE_PARM_DESC(message_level, "3c359: Level of reported messages \n") ;
+MODULE_PARM_DESC(message_level, "3c359: Level of reported messages") ;
/*
* This is a real nasty way of doing this, but otherwise you
* will be stuck with 1555 lines of hex #'s in the code.
static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data)
{
+ void *buf;
+ int err = -ENOMEM;
+
devdbg(dev, "dm_read() reg=0x%02x length=%d", reg, length);
- return usb_control_msg(dev->udev,
- usb_rcvctrlpipe(dev->udev, 0),
- DM_READ_REGS,
- USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
- 0, reg, data, length, USB_CTRL_SET_TIMEOUT);
+
+ buf = kmalloc(length, GFP_KERNEL);
+ if (!buf)
+ goto out;
+
+ err = usb_control_msg(dev->udev,
+ usb_rcvctrlpipe(dev->udev, 0),
+ DM_READ_REGS,
+ USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ 0, reg, buf, length, USB_CTRL_SET_TIMEOUT);
+ if (err == length)
+ memcpy(data, buf, length);
+ else if (err >= 0)
+ err = -EINVAL;
+ kfree(buf);
+
+ out:
+ return err;
}
static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value)
static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data)
{
+ void *buf = NULL;
+ int err = -ENOMEM;
+
devdbg(dev, "dm_write() reg=0x%02x, length=%d", reg, length);
- return usb_control_msg(dev->udev,
- usb_sndctrlpipe(dev->udev, 0),
- DM_WRITE_REGS,
- USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE,
- 0, reg, data, length, USB_CTRL_SET_TIMEOUT);
+
+ if (data) {
+ buf = kmalloc(length, GFP_KERNEL);
+ if (!buf)
+ goto out;
+ memcpy(buf, data, length);
+ }
+
+ err = usb_control_msg(dev->udev,
+ usb_sndctrlpipe(dev->udev, 0),
+ DM_WRITE_REGS,
+ USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE,
+ 0, reg, buf, length, USB_CTRL_SET_TIMEOUT);
+ kfree(buf);
+ if (err >= 0 && err < length)
+ err = -EINVAL;
+ out:
+ return err;
}
static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value)
}
}
+static int pegasus_blacklisted(struct usb_device *udev)
+{
+ struct usb_device_descriptor *udd = &udev->descriptor;
+
+ /* Special quirk to keep the driver from handling the Belkin Bluetooth
+ * dongle which happens to have the same ID.
+ */
+ if ((udd->idVendor == VENDOR_BELKIN && udd->idProduct == 0x0121) &&
+ (udd->bDeviceClass == USB_CLASS_WIRELESS_CONTROLLER) &&
+ (udd->bDeviceProtocol == 1))
+ return 1;
+
+ return 0;
+}
+
static int pegasus_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
DECLARE_MAC_BUF(mac);
usb_get_dev(dev);
+
+ if (pegasus_blacklisted(dev)) {
+ res = -ENODEV;
+ goto out;
+ }
+
net = alloc_etherdev(sizeof(struct pegasus));
if (!net) {
dev_err(&intf->dev, "can't allocate %s\n", "device");
spin_unlock_irq(&vptr->lock);
}
+static void velocity_init_rx_ring_indexes(struct velocity_info *vptr)
+{
+ vptr->rx.dirty = vptr->rx.filled = vptr->rx.curr = 0;
+}
/**
* velocity_rx_reset - handle a receive reset
struct mac_regs __iomem * regs = vptr->mac_regs;
int i;
- vptr->rd_dirty = vptr->rd_filled = vptr->rd_curr = 0;
+ velocity_init_rx_ring_indexes(vptr);
/*
* Init state, all RD entries belong to the NIC
*/
for (i = 0; i < vptr->options.numrx; ++i)
- vptr->rd_ring[i].rdesc0.len |= OWNED_BY_NIC;
+ vptr->rx.ring[i].rdesc0.len |= OWNED_BY_NIC;
writew(vptr->options.numrx, ®s->RBRDU);
- writel(vptr->rd_pool_dma, ®s->RDBaseLo);
+ writel(vptr->rx.pool_dma, ®s->RDBaseLo);
writew(0, ®s->RDIdx);
writew(vptr->options.numrx - 1, ®s->RDCSize);
}
vptr->int_mask = INT_MASK_DEF;
- writel(vptr->rd_pool_dma, ®s->RDBaseLo);
+ writel(vptr->rx.pool_dma, ®s->RDBaseLo);
writew(vptr->options.numrx - 1, ®s->RDCSize);
mac_rx_queue_run(regs);
mac_rx_queue_wake(regs);
writew(vptr->options.numtx - 1, ®s->TDCSize);
- for (i = 0; i < vptr->num_txq; i++) {
- writel(vptr->td_pool_dma[i], ®s->TDBaseLo[i]);
+ for (i = 0; i < vptr->tx.numq; i++) {
+ writel(vptr->tx.pool_dma[i], ®s->TDBaseLo[i]);
mac_tx_queue_run(regs, i);
}
vptr->pdev = pdev;
vptr->chip_id = info->chip_id;
- vptr->num_txq = info->txqueue;
+ vptr->tx.numq = info->txqueue;
vptr->multicast_limit = MCAM_SIZE;
spin_lock_init(&vptr->lock);
INIT_LIST_HEAD(&vptr->list);
}
/**
- * velocity_init_rings - set up DMA rings
+ * velocity_init_dma_rings - set up DMA rings
* @vptr: Velocity to set up
*
* Allocate PCI mapped DMA rings for the receive and transmit layer
* to use.
*/
-static int velocity_init_rings(struct velocity_info *vptr)
+static int velocity_init_dma_rings(struct velocity_info *vptr)
{
struct velocity_opt *opt = &vptr->options;
const unsigned int rx_ring_size = opt->numrx * sizeof(struct rx_desc);
* pci_alloc_consistent() fulfills the requirement for 64 bytes
* alignment
*/
- pool = pci_alloc_consistent(pdev, tx_ring_size * vptr->num_txq +
+ pool = pci_alloc_consistent(pdev, tx_ring_size * vptr->tx.numq +
rx_ring_size, &pool_dma);
if (!pool) {
dev_err(&pdev->dev, "%s : DMA memory allocation failed.\n",
return -ENOMEM;
}
- vptr->rd_ring = pool;
- vptr->rd_pool_dma = pool_dma;
+ vptr->rx.ring = pool;
+ vptr->rx.pool_dma = pool_dma;
pool += rx_ring_size;
pool_dma += rx_ring_size;
- for (i = 0; i < vptr->num_txq; i++) {
- vptr->td_rings[i] = pool;
- vptr->td_pool_dma[i] = pool_dma;
+ for (i = 0; i < vptr->tx.numq; i++) {
+ vptr->tx.rings[i] = pool;
+ vptr->tx.pool_dma[i] = pool_dma;
pool += tx_ring_size;
pool_dma += tx_ring_size;
}
}
/**
- * velocity_free_rings - free PCI ring pointers
+ * velocity_free_dma_rings - free PCI ring pointers
* @vptr: Velocity to free from
*
* Clean up the PCI ring buffers allocated to this velocity.
*/
-static void velocity_free_rings(struct velocity_info *vptr)
+static void velocity_free_dma_rings(struct velocity_info *vptr)
{
const int size = vptr->options.numrx * sizeof(struct rx_desc) +
- vptr->options.numtx * sizeof(struct tx_desc) * vptr->num_txq;
+ vptr->options.numtx * sizeof(struct tx_desc) * vptr->tx.numq;
- pci_free_consistent(vptr->pdev, size, vptr->rd_ring, vptr->rd_pool_dma);
+ pci_free_consistent(vptr->pdev, size, vptr->rx.ring, vptr->rx.pool_dma);
}
static void velocity_give_many_rx_descs(struct velocity_info *vptr)
* RD number must be equal to 4X per hardware spec
* (programming guide rev 1.20, p.13)
*/
- if (vptr->rd_filled < 4)
+ if (vptr->rx.filled < 4)
return;
wmb();
- unusable = vptr->rd_filled & 0x0003;
- dirty = vptr->rd_dirty - unusable;
- for (avail = vptr->rd_filled & 0xfffc; avail; avail--) {
+ unusable = vptr->rx.filled & 0x0003;
+ dirty = vptr->rx.dirty - unusable;
+ for (avail = vptr->rx.filled & 0xfffc; avail; avail--) {
dirty = (dirty > 0) ? dirty - 1 : vptr->options.numrx - 1;
- vptr->rd_ring[dirty].rdesc0.len |= OWNED_BY_NIC;
+ vptr->rx.ring[dirty].rdesc0.len |= OWNED_BY_NIC;
}
- writew(vptr->rd_filled & 0xfffc, ®s->RBRDU);
- vptr->rd_filled = unusable;
+ writew(vptr->rx.filled & 0xfffc, ®s->RBRDU);
+ vptr->rx.filled = unusable;
}
static int velocity_rx_refill(struct velocity_info *vptr)
{
- int dirty = vptr->rd_dirty, done = 0;
+ int dirty = vptr->rx.dirty, done = 0;
do {
- struct rx_desc *rd = vptr->rd_ring + dirty;
+ struct rx_desc *rd = vptr->rx.ring + dirty;
/* Fine for an all zero Rx desc at init time as well */
if (rd->rdesc0.len & OWNED_BY_NIC)
break;
- if (!vptr->rd_info[dirty].skb) {
+ if (!vptr->rx.info[dirty].skb) {
if (velocity_alloc_rx_buf(vptr, dirty) < 0)
break;
}
done++;
dirty = (dirty < vptr->options.numrx - 1) ? dirty + 1 : 0;
- } while (dirty != vptr->rd_curr);
+ } while (dirty != vptr->rx.curr);
if (done) {
- vptr->rd_dirty = dirty;
- vptr->rd_filled += done;
+ vptr->rx.dirty = dirty;
+ vptr->rx.filled += done;
}
return done;
static void velocity_set_rxbufsize(struct velocity_info *vptr, int mtu)
{
- vptr->rx_buf_sz = (mtu <= ETH_DATA_LEN) ? PKT_BUF_SZ : mtu + 32;
+ vptr->rx.buf_sz = (mtu <= ETH_DATA_LEN) ? PKT_BUF_SZ : mtu + 32;
}
/**
{
int ret = -ENOMEM;
- vptr->rd_info = kcalloc(vptr->options.numrx,
+ vptr->rx.info = kcalloc(vptr->options.numrx,
sizeof(struct velocity_rd_info), GFP_KERNEL);
- if (!vptr->rd_info)
+ if (!vptr->rx.info)
goto out;
- vptr->rd_filled = vptr->rd_dirty = vptr->rd_curr = 0;
+ velocity_init_rx_ring_indexes(vptr);
if (velocity_rx_refill(vptr) != vptr->options.numrx) {
VELOCITY_PRT(MSG_LEVEL_ERR, KERN_ERR
{
int i;
- if (vptr->rd_info == NULL)
+ if (vptr->rx.info == NULL)
return;
for (i = 0; i < vptr->options.numrx; i++) {
- struct velocity_rd_info *rd_info = &(vptr->rd_info[i]);
- struct rx_desc *rd = vptr->rd_ring + i;
+ struct velocity_rd_info *rd_info = &(vptr->rx.info[i]);
+ struct rx_desc *rd = vptr->rx.ring + i;
memset(rd, 0, sizeof(*rd));
if (!rd_info->skb)
continue;
- pci_unmap_single(vptr->pdev, rd_info->skb_dma, vptr->rx_buf_sz,
+ pci_unmap_single(vptr->pdev, rd_info->skb_dma, vptr->rx.buf_sz,
PCI_DMA_FROMDEVICE);
rd_info->skb_dma = (dma_addr_t) NULL;
rd_info->skb = NULL;
}
- kfree(vptr->rd_info);
- vptr->rd_info = NULL;
+ kfree(vptr->rx.info);
+ vptr->rx.info = NULL;
}
/**
unsigned int j;
/* Init the TD ring entries */
- for (j = 0; j < vptr->num_txq; j++) {
- curr = vptr->td_pool_dma[j];
+ for (j = 0; j < vptr->tx.numq; j++) {
+ curr = vptr->tx.pool_dma[j];
- vptr->td_infos[j] = kcalloc(vptr->options.numtx,
+ vptr->tx.infos[j] = kcalloc(vptr->options.numtx,
sizeof(struct velocity_td_info),
GFP_KERNEL);
- if (!vptr->td_infos[j]) {
+ if (!vptr->tx.infos[j]) {
while(--j >= 0)
- kfree(vptr->td_infos[j]);
+ kfree(vptr->tx.infos[j]);
return -ENOMEM;
}
- vptr->td_tail[j] = vptr->td_curr[j] = vptr->td_used[j] = 0;
+ vptr->tx.tail[j] = vptr->tx.curr[j] = vptr->tx.used[j] = 0;
}
return 0;
}
static void velocity_free_td_ring_entry(struct velocity_info *vptr,
int q, int n)
{
- struct velocity_td_info * td_info = &(vptr->td_infos[q][n]);
+ struct velocity_td_info * td_info = &(vptr->tx.infos[q][n]);
int i;
if (td_info == NULL)
{
int i, j;
- for (j = 0; j < vptr->num_txq; j++) {
- if (vptr->td_infos[j] == NULL)
+ for (j = 0; j < vptr->tx.numq; j++) {
+ if (vptr->tx.infos[j] == NULL)
continue;
for (i = 0; i < vptr->options.numtx; i++) {
velocity_free_td_ring_entry(vptr, j, i);
}
- kfree(vptr->td_infos[j]);
- vptr->td_infos[j] = NULL;
+ kfree(vptr->tx.infos[j]);
+ vptr->tx.infos[j] = NULL;
}
}
static int velocity_rx_srv(struct velocity_info *vptr, int status)
{
struct net_device_stats *stats = &vptr->stats;
- int rd_curr = vptr->rd_curr;
+ int rd_curr = vptr->rx.curr;
int works = 0;
do {
- struct rx_desc *rd = vptr->rd_ring + rd_curr;
+ struct rx_desc *rd = vptr->rx.ring + rd_curr;
- if (!vptr->rd_info[rd_curr].skb)
+ if (!vptr->rx.info[rd_curr].skb)
break;
if (rd->rdesc0.len & OWNED_BY_NIC)
rd_curr = 0;
} while (++works <= 15);
- vptr->rd_curr = rd_curr;
+ vptr->rx.curr = rd_curr;
if ((works > 0) && (velocity_rx_refill(vptr) > 0))
velocity_give_many_rx_descs(vptr);
{
void (*pci_action)(struct pci_dev *, dma_addr_t, size_t, int);
struct net_device_stats *stats = &vptr->stats;
- struct velocity_rd_info *rd_info = &(vptr->rd_info[idx]);
- struct rx_desc *rd = &(vptr->rd_ring[idx]);
+ struct velocity_rd_info *rd_info = &(vptr->rx.info[idx]);
+ struct rx_desc *rd = &(vptr->rx.ring[idx]);
int pkt_len = le16_to_cpu(rd->rdesc0.len) & 0x3fff;
struct sk_buff *skb;
skb = rd_info->skb;
pci_dma_sync_single_for_cpu(vptr->pdev, rd_info->skb_dma,
- vptr->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ vptr->rx.buf_sz, PCI_DMA_FROMDEVICE);
/*
* Drop frame not meeting IEEE 802.3
rd_info->skb = NULL;
}
- pci_action(vptr->pdev, rd_info->skb_dma, vptr->rx_buf_sz,
+ pci_action(vptr->pdev, rd_info->skb_dma, vptr->rx.buf_sz,
PCI_DMA_FROMDEVICE);
skb_put(skb, pkt_len - 4);
static int velocity_alloc_rx_buf(struct velocity_info *vptr, int idx)
{
- struct rx_desc *rd = &(vptr->rd_ring[idx]);
- struct velocity_rd_info *rd_info = &(vptr->rd_info[idx]);
+ struct rx_desc *rd = &(vptr->rx.ring[idx]);
+ struct velocity_rd_info *rd_info = &(vptr->rx.info[idx]);
- rd_info->skb = netdev_alloc_skb(vptr->dev, vptr->rx_buf_sz + 64);
+ rd_info->skb = dev_alloc_skb(vptr->rx.buf_sz + 64);
if (rd_info->skb == NULL)
return -ENOMEM;
* 64byte alignment.
*/
skb_reserve(rd_info->skb, (unsigned long) rd_info->skb->data & 63);
- rd_info->skb_dma = pci_map_single(vptr->pdev, rd_info->skb->data, vptr->rx_buf_sz, PCI_DMA_FROMDEVICE);
+ rd_info->skb_dma = pci_map_single(vptr->pdev, rd_info->skb->data,
+ vptr->rx.buf_sz, PCI_DMA_FROMDEVICE);
/*
* Fill in the descriptor to match
- */
+ */
*((u32 *) & (rd->rdesc0)) = 0;
- rd->size = cpu_to_le16(vptr->rx_buf_sz) | RX_INTEN;
+ rd->size = cpu_to_le16(vptr->rx.buf_sz) | RX_INTEN;
rd->pa_low = cpu_to_le32(rd_info->skb_dma);
rd->pa_high = 0;
return 0;
struct velocity_td_info *tdinfo;
struct net_device_stats *stats = &vptr->stats;
- for (qnum = 0; qnum < vptr->num_txq; qnum++) {
- for (idx = vptr->td_tail[qnum]; vptr->td_used[qnum] > 0;
+ for (qnum = 0; qnum < vptr->tx.numq; qnum++) {
+ for (idx = vptr->tx.tail[qnum]; vptr->tx.used[qnum] > 0;
idx = (idx + 1) % vptr->options.numtx) {
/*
* Get Tx Descriptor
*/
- td = &(vptr->td_rings[qnum][idx]);
- tdinfo = &(vptr->td_infos[qnum][idx]);
+ td = &(vptr->tx.rings[qnum][idx]);
+ tdinfo = &(vptr->tx.infos[qnum][idx]);
if (td->tdesc0.len & OWNED_BY_NIC)
break;
stats->tx_bytes += tdinfo->skb->len;
}
velocity_free_tx_buf(vptr, tdinfo);
- vptr->td_used[qnum]--;
+ vptr->tx.used[qnum]--;
}
- vptr->td_tail[qnum] = idx;
+ vptr->tx.tail[qnum] = idx;
if (AVAIL_TD(vptr, qnum) < 1) {
full = 1;
tdinfo->skb = NULL;
}
+static int velocity_init_rings(struct velocity_info *vptr, int mtu)
+{
+ int ret;
+
+ velocity_set_rxbufsize(vptr, mtu);
+
+ ret = velocity_init_dma_rings(vptr);
+ if (ret < 0)
+ goto out;
+
+ ret = velocity_init_rd_ring(vptr);
+ if (ret < 0)
+ goto err_free_dma_rings_0;
+
+ ret = velocity_init_td_ring(vptr);
+ if (ret < 0)
+ goto err_free_rd_ring_1;
+out:
+ return ret;
+
+err_free_rd_ring_1:
+ velocity_free_rd_ring(vptr);
+err_free_dma_rings_0:
+ velocity_free_dma_rings(vptr);
+ goto out;
+}
+
+static void velocity_free_rings(struct velocity_info *vptr)
+{
+ velocity_free_td_ring(vptr);
+ velocity_free_rd_ring(vptr);
+ velocity_free_dma_rings(vptr);
+}
+
/**
* velocity_open - interface activation callback
* @dev: network layer device to open
struct velocity_info *vptr = netdev_priv(dev);
int ret;
- velocity_set_rxbufsize(vptr, dev->mtu);
-
- ret = velocity_init_rings(vptr);
+ ret = velocity_init_rings(vptr, dev->mtu);
if (ret < 0)
goto out;
- ret = velocity_init_rd_ring(vptr);
- if (ret < 0)
- goto err_free_desc_rings;
-
- ret = velocity_init_td_ring(vptr);
- if (ret < 0)
- goto err_free_rd_ring;
-
/* Ensure chip is running */
pci_set_power_state(vptr->pdev, PCI_D0);
if (ret < 0) {
/* Power down the chip */
pci_set_power_state(vptr->pdev, PCI_D3hot);
- goto err_free_td_ring;
+ velocity_free_rings(vptr);
+ goto out;
}
mac_enable_int(vptr->mac_regs);
vptr->flags |= VELOCITY_FLAGS_OPENED;
out:
return ret;
-
-err_free_td_ring:
- velocity_free_td_ring(vptr);
-err_free_rd_ring:
- velocity_free_rd_ring(vptr);
-err_free_desc_rings:
- velocity_free_rings(vptr);
- goto out;
}
/**
static int velocity_change_mtu(struct net_device *dev, int new_mtu)
{
struct velocity_info *vptr = netdev_priv(dev);
- unsigned long flags;
- int oldmtu = dev->mtu;
int ret = 0;
if ((new_mtu < VELOCITY_MIN_MTU) || new_mtu > (VELOCITY_MAX_MTU)) {
VELOCITY_PRT(MSG_LEVEL_ERR, KERN_NOTICE "%s: Invalid MTU.\n",
vptr->dev->name);
- return -EINVAL;
+ ret = -EINVAL;
+ goto out_0;
}
if (!netif_running(dev)) {
dev->mtu = new_mtu;
- return 0;
+ goto out_0;
}
- if (new_mtu != oldmtu) {
+ if (dev->mtu != new_mtu) {
+ struct velocity_info *tmp_vptr;
+ unsigned long flags;
+ struct rx_info rx;
+ struct tx_info tx;
+
+ tmp_vptr = kzalloc(sizeof(*tmp_vptr), GFP_KERNEL);
+ if (!tmp_vptr) {
+ ret = -ENOMEM;
+ goto out_0;
+ }
+
+ tmp_vptr->dev = dev;
+ tmp_vptr->pdev = vptr->pdev;
+ tmp_vptr->options = vptr->options;
+ tmp_vptr->tx.numq = vptr->tx.numq;
+
+ ret = velocity_init_rings(tmp_vptr, new_mtu);
+ if (ret < 0)
+ goto out_free_tmp_vptr_1;
+
spin_lock_irqsave(&vptr->lock, flags);
netif_stop_queue(dev);
velocity_shutdown(vptr);
- velocity_free_td_ring(vptr);
- velocity_free_rd_ring(vptr);
+ rx = vptr->rx;
+ tx = vptr->tx;
- dev->mtu = new_mtu;
+ vptr->rx = tmp_vptr->rx;
+ vptr->tx = tmp_vptr->tx;
- velocity_set_rxbufsize(vptr, new_mtu);
+ tmp_vptr->rx = rx;
+ tmp_vptr->tx = tx;
- ret = velocity_init_rd_ring(vptr);
- if (ret < 0)
- goto out_unlock;
+ dev->mtu = new_mtu;
- ret = velocity_init_td_ring(vptr);
- if (ret < 0)
- goto out_unlock;
+ velocity_give_many_rx_descs(vptr);
velocity_init_registers(vptr, VELOCITY_INIT_COLD);
mac_enable_int(vptr->mac_regs);
netif_start_queue(dev);
-out_unlock:
+
spin_unlock_irqrestore(&vptr->lock, flags);
- }
+ velocity_free_rings(tmp_vptr);
+
+out_free_tmp_vptr_1:
+ kfree(tmp_vptr);
+ }
+out_0:
return ret;
}
/* Power down the chip */
pci_set_power_state(vptr->pdev, PCI_D3hot);
- /* Free the resources */
- velocity_free_td_ring(vptr);
- velocity_free_rd_ring(vptr);
velocity_free_rings(vptr);
vptr->flags &= (~VELOCITY_FLAGS_OPENED);
spin_lock_irqsave(&vptr->lock, flags);
- index = vptr->td_curr[qnum];
- td_ptr = &(vptr->td_rings[qnum][index]);
- tdinfo = &(vptr->td_infos[qnum][index]);
+ index = vptr->tx.curr[qnum];
+ td_ptr = &(vptr->tx.rings[qnum][index]);
+ tdinfo = &(vptr->tx.infos[qnum][index]);
td_ptr->tdesc1.TCR = TCR0_TIC;
td_ptr->td_buf[0].size &= ~TD_QUEUE;
skb_copy_from_linear_data(skb, tdinfo->buf, skb->len);
tdinfo->skb_dma[0] = tdinfo->buf_dma;
td_ptr->tdesc0.len = len;
- td_ptr->td_buf[0].pa_low = cpu_to_le32(tdinfo->skb_dma[0]);
- td_ptr->td_buf[0].pa_high = 0;
- td_ptr->td_buf[0].size = len; /* queue is 0 anyway */
+ td_ptr->tx.buf[0].pa_low = cpu_to_le32(tdinfo->skb_dma[0]);
+ td_ptr->tx.buf[0].pa_high = 0;
+ td_ptr->tx.buf[0].size = len; /* queue is 0 anyway */
tdinfo->nskb_dma = 1;
} else {
int i = 0;
td_ptr->tdesc0.len = len;
/* FIXME: support 48bit DMA later */
- td_ptr->td_buf[i].pa_low = cpu_to_le32(tdinfo->skb_dma);
- td_ptr->td_buf[i].pa_high = 0;
- td_ptr->td_buf[i].size = cpu_to_le16(skb_headlen(skb));
+ td_ptr->tx.buf[i].pa_low = cpu_to_le32(tdinfo->skb_dma);
+ td_ptr->tx.buf[i].pa_high = 0;
+ td_ptr->tx.buf[i].size = cpu_to_le16(skb_headlen(skb));
for (i = 0; i < nfrags; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
tdinfo->skb_dma[i + 1] = pci_map_single(vptr->pdev, addr, frag->size, PCI_DMA_TODEVICE);
- td_ptr->td_buf[i + 1].pa_low = cpu_to_le32(tdinfo->skb_dma[i + 1]);
- td_ptr->td_buf[i + 1].pa_high = 0;
- td_ptr->td_buf[i + 1].size = cpu_to_le16(frag->size);
+ td_ptr->tx.buf[i + 1].pa_low = cpu_to_le32(tdinfo->skb_dma[i + 1]);
+ td_ptr->tx.buf[i + 1].pa_high = 0;
+ td_ptr->tx.buf[i + 1].size = cpu_to_le16(frag->size);
}
tdinfo->nskb_dma = i - 1;
}
if (prev < 0)
prev = vptr->options.numtx - 1;
td_ptr->tdesc0.len |= OWNED_BY_NIC;
- vptr->td_used[qnum]++;
- vptr->td_curr[qnum] = (index + 1) % vptr->options.numtx;
+ vptr->tx.used[qnum]++;
+ vptr->tx.curr[qnum] = (index + 1) % vptr->options.numtx;
if (AVAIL_TD(vptr, qnum) < 1)
netif_stop_queue(dev);
- td_ptr = &(vptr->td_rings[qnum][prev]);
+ td_ptr = &(vptr->tx.rings[qnum][prev]);
td_ptr->td_buf[0].size |= TD_QUEUE;
mac_tx_queue_wake(vptr->mac_regs, qnum);
}
velocity_tx_srv(vptr, 0);
- for (i = 0; i < vptr->num_txq; i++) {
- if (vptr->td_used[i]) {
+ for (i = 0; i < vptr->tx.numq; i++) {
+ if (vptr->tx.used[i]) {
mac_tx_queue_wake(vptr->mac_regs, i);
}
}
u32 flags;
};
+#define AVAIL_TD(p,q) ((p)->options.numtx-((p)->tx.used[(q)]))
+
+#define GET_RD_BY_IDX(vptr, idx) (vptr->rd_ring[idx])
+
struct velocity_info {
struct list_head list;
struct net_device *dev;
struct net_device_stats stats;
- dma_addr_t rd_pool_dma;
- dma_addr_t td_pool_dma[TX_QUEUE_NO];
-
struct vlan_group *vlgrp;
u8 ip_addr[4];
enum chip_type chip_id;
unsigned long memaddr;
unsigned long ioaddr;
- u8 rev_id;
-
-#define AVAIL_TD(p,q) ((p)->options.numtx-((p)->td_used[(q)]))
+ struct tx_info {
+ int numq;
+
+ /* FIXME: the locality of the data seems rather poor. */
+ int used[TX_QUEUE_NO];
+ int curr[TX_QUEUE_NO];
+ int tail[TX_QUEUE_NO];
+ struct tx_desc *rings[TX_QUEUE_NO];
+ struct velocity_td_info *infos[TX_QUEUE_NO];
+ dma_addr_t pool_dma[TX_QUEUE_NO];
+ } tx;
+
+ struct rx_info {
+ int buf_sz;
+
+ int dirty;
+ int curr;
+ u32 filled;
+ struct rx_desc *ring;
+ struct velocity_rd_info *info; /* It's an array */
+ dma_addr_t pool_dma;
+ } rx;
- int num_txq;
-
- volatile int td_used[TX_QUEUE_NO];
- int td_curr[TX_QUEUE_NO];
- int td_tail[TX_QUEUE_NO];
- struct tx_desc *td_rings[TX_QUEUE_NO];
- struct velocity_td_info *td_infos[TX_QUEUE_NO];
-
- int rd_curr;
- int rd_dirty;
- u32 rd_filled;
- struct rx_desc *rd_ring;
- struct velocity_rd_info *rd_info; /* It's an array */
-
-#define GET_RD_BY_IDX(vptr, idx) (vptr->rd_ring[idx])
u32 mib_counter[MAX_HW_MIB_COUNTER];
struct velocity_opt options;
u32 flags;
- int rx_buf_sz;
u32 mii_status;
u32 phy_id;
int multicast_limit;
struct velocity_context context;
u32 ticks;
- u32 rx_bytes;
+ u8 rev_id;
};
/**
# There is no way to detect a comtrol sv11 - force it modular for now.
config HOSTESS_SV11
tristate "Comtrol Hostess SV-11 support"
- depends on ISA && m && ISA_DMA_API && INET
+ depends on ISA && m && ISA_DMA_API && INET && HDLC
help
Driver for Comtrol Hostess SV-11 network card which
operates on low speed synchronous serial links at up to
# The COSA/SRP driver has not been tested as non-modular yet.
config COSA
tristate "COSA/SRP sync serial boards support"
- depends on ISA && m && ISA_DMA_API
+ depends on ISA && m && ISA_DMA_API && HDLC
---help---
Driver for COSA and SRP synchronous serial boards.
#
config LANMEDIA
tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards"
- depends on PCI && VIRT_TO_BUS
+ depends on PCI && VIRT_TO_BUS && HDLC
---help---
Driver for the following Lan Media family of serial boards:
- LMC 5245 board connects directly to a T3 circuit saving the
additional external hardware.
- To change setting such as syncPPP vs Cisco HDLC or clock source you
- will need lmcctl. It is available at <ftp://ftp.lanmedia.com/>
- (broken link).
+ To change setting such as clock source you will need lmcctl.
+ It is available at <ftp://ftp.lanmedia.com/> (broken link).
To compile this driver as a module, choose M here: the
module will be called lmc.
# There is no way to detect a Sealevel board. Force it modular
config SEALEVEL_4021
tristate "Sealevel Systems 4021 support"
- depends on ISA && m && ISA_DMA_API && INET
+ depends on ISA && m && ISA_DMA_API && INET && HDLC
help
This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.
help
Generic HDLC driver supporting PPP over WAN connections.
- It will be replaced by new PPP implementation in Linux 2.6.26.
-
If unsure, say N.
config HDLC_X25
pc300-$(CONFIG_PC300_MLPPP) += pc300_tty.o
pc300-objs := $(pc300-y)
-obj-$(CONFIG_HOSTESS_SV11) += z85230.o syncppp.o hostess_sv11.o
-obj-$(CONFIG_SEALEVEL_4021) += z85230.o syncppp.o sealevel.o
-obj-$(CONFIG_COSA) += syncppp.o cosa.o
-obj-$(CONFIG_FARSYNC) += syncppp.o farsync.o
-obj-$(CONFIG_DSCC4) += dscc4.o
-obj-$(CONFIG_LANMEDIA) += syncppp.o
+obj-$(CONFIG_HOSTESS_SV11) += z85230.o hostess_sv11.o
+obj-$(CONFIG_SEALEVEL_4021) += z85230.o sealevel.o
+obj-$(CONFIG_COSA) += cosa.o
+obj-$(CONFIG_FARSYNC) += farsync.o
+obj-$(CONFIG_DSCC4) += dscc4.o
obj-$(CONFIG_X25_ASY) += x25_asy.o
obj-$(CONFIG_LANMEDIA) += lmc/
/*
* Copyright (C) 1995-1997 Jan "Yenya" Kasprzak <kas@fi.muni.cz>
+ * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
*
* The Linux driver (unlike the present *BSD drivers :-) can work even
* for the COSA and SRP in one computer and allows each channel to work
- * in one of the three modes (character device, Cisco HDLC, Sync PPP).
+ * in one of the two modes (character or network device).
*
* AUTHOR
*
* The Comtrol Hostess SV11 driver by Alan Cox
* The Sync PPP/Cisco HDLC layer (syncppp.c) ported to Linux by Alan Cox
*/
-/*
- * 5/25/1999 : Marcelo Tosatti <marcelo@conectiva.com.br>
- * fixed a deadlock in cosa_sppp_open
- */
-\f
-/* ---------- Headers, macros, data structures ---------- */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/fs.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
+#include <linux/hdlc.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/netdevice.h>
#include <linux/mutex.h>
#include <linux/device.h>
#include <linux/smp_lock.h>
-
-#undef COSA_SLOW_IO /* for testing purposes only */
-
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/byteorder.h>
-#include <net/syncppp.h>
+#undef COSA_SLOW_IO /* for testing purposes only */
+
#include "cosa.h"
/* Maximum length of the identification string. */
/* Per-channel data structure */
struct channel_data {
- void *if_ptr; /* General purpose pointer (used by SPPP) */
int usage; /* Usage count; >0 for chrdev, -1 for netdev */
int num; /* Number of the channel */
struct cosa_data *cosa; /* Pointer to the per-card structure */
wait_queue_head_t txwaitq, rxwaitq;
int tx_status, rx_status;
- /* SPPP/HDLC device parts */
- struct ppp_device pppdev;
+ /* generic HDLC device parts */
+ struct net_device *netdev;
struct sk_buff *rx_skb, *tx_skb;
- struct net_device_stats stats;
};
/* cosa->firmware_status bits */
static void cosa_kick(struct cosa_data *cosa);
static int cosa_dma_able(struct channel_data *chan, char *buf, int data);
-/* SPPP/HDLC stuff */
-static void sppp_channel_init(struct channel_data *chan);
-static void sppp_channel_delete(struct channel_data *chan);
-static int cosa_sppp_open(struct net_device *d);
-static int cosa_sppp_close(struct net_device *d);
-static void cosa_sppp_timeout(struct net_device *d);
-static int cosa_sppp_tx(struct sk_buff *skb, struct net_device *d);
-static char *sppp_setup_rx(struct channel_data *channel, int size);
-static int sppp_rx_done(struct channel_data *channel);
-static int sppp_tx_done(struct channel_data *channel, int size);
-static int cosa_sppp_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
-static struct net_device_stats *cosa_net_stats(struct net_device *dev);
+/* Network device stuff */
+static int cosa_net_attach(struct net_device *dev, unsigned short encoding,
+ unsigned short parity);
+static int cosa_net_open(struct net_device *d);
+static int cosa_net_close(struct net_device *d);
+static void cosa_net_timeout(struct net_device *d);
+static int cosa_net_tx(struct sk_buff *skb, struct net_device *d);
+static char *cosa_net_setup_rx(struct channel_data *channel, int size);
+static int cosa_net_rx_done(struct channel_data *channel);
+static int cosa_net_tx_done(struct channel_data *channel, int size);
+static int cosa_net_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
/* Character device */
-static void chardev_channel_init(struct channel_data *chan);
static char *chrdev_setup_rx(struct channel_data *channel, int size);
static int chrdev_rx_done(struct channel_data *channel);
static int chrdev_tx_done(struct channel_data *channel, int size);
static void debug_status_out(struct cosa_data *cosa, int status);
#endif
-\f
+static inline struct channel_data* dev_to_chan(struct net_device *dev)
+{
+ return (struct channel_data *)dev_to_hdlc(dev)->priv;
+}
+
/* ---------- Initialization stuff ---------- */
static int __init cosa_init(void)
{
int i, err = 0;
- printk(KERN_INFO "cosa v1.08 (c) 1997-2000 Jan Kasprzak <kas@fi.muni.cz>\n");
-#ifdef CONFIG_SMP
- printk(KERN_INFO "cosa: SMP found. Please mail any success/failure reports to the author.\n");
-#endif
if (cosa_major > 0) {
if (register_chrdev(cosa_major, "cosa", &cosa_fops)) {
printk(KERN_WARNING "cosa: unable to get major %d\n",
NULL, "cosa%d", i);
err = 0;
goto out;
-
+
out_chrdev:
unregister_chrdev(cosa_major, "cosa");
out:
{
struct cosa_data *cosa;
int i;
- printk(KERN_INFO "Unloading the cosa module\n");
- for (i=0; i<nr_cards; i++)
+ for (i = 0; i < nr_cards; i++)
device_destroy(cosa_class, MKDEV(cosa_major, i));
class_destroy(cosa_class);
- for (cosa=cosa_cards; nr_cards--; cosa++) {
+
+ for (cosa = cosa_cards; nr_cards--; cosa++) {
/* Clean up the per-channel data */
- for (i=0; i<cosa->nchannels; i++) {
+ for (i = 0; i < cosa->nchannels; i++) {
/* Chardev driver has no alloc'd per-channel data */
- sppp_channel_delete(cosa->chan+i);
+ unregister_hdlc_device(cosa->chan[i].netdev);
+ free_netdev(cosa->chan[i].netdev);
}
/* Clean up the per-card data */
kfree(cosa->chan);
kfree(cosa->bouncebuf);
free_irq(cosa->irq, cosa);
free_dma(cosa->dma);
- release_region(cosa->datareg,is_8bit(cosa)?2:4);
+ release_region(cosa->datareg, is_8bit(cosa) ? 2 : 4);
}
unregister_chrdev(cosa_major, "cosa");
}
module_exit(cosa_exit);
-/*
- * This function should register all the net devices needed for the
- * single channel.
- */
-static __inline__ void channel_init(struct channel_data *chan)
-{
- sprintf(chan->name, "cosa%dc%d", chan->cosa->num, chan->num);
-
- /* Initialize the chardev data structures */
- chardev_channel_init(chan);
-
- /* Register the sppp interface */
- sppp_channel_init(chan);
-}
-
static int cosa_probe(int base, int irq, int dma)
{
struct cosa_data *cosa = cosa_cards+nr_cards;
/* Initialize the per-channel data */
cosa->chan = kcalloc(cosa->nchannels, sizeof(struct channel_data), GFP_KERNEL);
if (!cosa->chan) {
- err = -ENOMEM;
+ err = -ENOMEM;
goto err_out3;
}
- for (i=0; i<cosa->nchannels; i++) {
- cosa->chan[i].cosa = cosa;
- cosa->chan[i].num = i;
- channel_init(cosa->chan+i);
+
+ for (i = 0; i < cosa->nchannels; i++) {
+ struct channel_data *chan = &cosa->chan[i];
+
+ chan->cosa = cosa;
+ chan->num = i;
+ sprintf(chan->name, "cosa%dc%d", chan->cosa->num, i);
+
+ /* Initialize the chardev data structures */
+ mutex_init(&chan->rlock);
+ init_MUTEX(&chan->wsem);
+
+ /* Register the network interface */
+ if (!(chan->netdev = alloc_hdlcdev(chan))) {
+ printk(KERN_WARNING "%s: alloc_hdlcdev failed.\n",
+ chan->name);
+ goto err_hdlcdev;
+ }
+ dev_to_hdlc(chan->netdev)->attach = cosa_net_attach;
+ dev_to_hdlc(chan->netdev)->xmit = cosa_net_tx;
+ chan->netdev->open = cosa_net_open;
+ chan->netdev->stop = cosa_net_close;
+ chan->netdev->do_ioctl = cosa_net_ioctl;
+ chan->netdev->tx_timeout = cosa_net_timeout;
+ chan->netdev->watchdog_timeo = TX_TIMEOUT;
+ chan->netdev->base_addr = chan->cosa->datareg;
+ chan->netdev->irq = chan->cosa->irq;
+ chan->netdev->dma = chan->cosa->dma;
+ if (register_hdlc_device(chan->netdev)) {
+ printk(KERN_WARNING "%s: register_hdlc_device()"
+ " failed.\n", chan->netdev->name);
+ free_netdev(chan->netdev);
+ goto err_hdlcdev;
+ }
}
printk (KERN_INFO "cosa%d: %s (%s at 0x%x irq %d dma %d), %d channels\n",
cosa->datareg, cosa->irq, cosa->dma, cosa->nchannels);
return nr_cards++;
+
+err_hdlcdev:
+ while (i-- > 0) {
+ unregister_hdlc_device(cosa->chan[i].netdev);
+ free_netdev(cosa->chan[i].netdev);
+ }
+ kfree(cosa->chan);
err_out3:
kfree(cosa->bouncebuf);
err_out2:
free_dma(cosa->dma);
err_out1:
free_irq(cosa->irq, cosa);
-err_out:
+err_out:
release_region(cosa->datareg,is_8bit(cosa)?2:4);
printk(KERN_NOTICE "cosa%d: allocating resources failed\n",
cosa->num);
}
\f
-/*---------- SPPP/HDLC netdevice ---------- */
+/*---------- network device ---------- */
-static void cosa_setup(struct net_device *d)
+static int cosa_net_attach(struct net_device *dev, unsigned short encoding,
+ unsigned short parity)
{
- d->open = cosa_sppp_open;
- d->stop = cosa_sppp_close;
- d->hard_start_xmit = cosa_sppp_tx;
- d->do_ioctl = cosa_sppp_ioctl;
- d->get_stats = cosa_net_stats;
- d->tx_timeout = cosa_sppp_timeout;
- d->watchdog_timeo = TX_TIMEOUT;
-}
-
-static void sppp_channel_init(struct channel_data *chan)
-{
- struct net_device *d;
- chan->if_ptr = &chan->pppdev;
- d = alloc_netdev(0, chan->name, cosa_setup);
- if (!d) {
- printk(KERN_WARNING "%s: alloc_netdev failed.\n", chan->name);
- return;
- }
- chan->pppdev.dev = d;
- d->base_addr = chan->cosa->datareg;
- d->irq = chan->cosa->irq;
- d->dma = chan->cosa->dma;
- d->ml_priv = chan;
- sppp_attach(&chan->pppdev);
- if (register_netdev(d)) {
- printk(KERN_WARNING "%s: register_netdev failed.\n", d->name);
- sppp_detach(d);
- free_netdev(d);
- chan->pppdev.dev = NULL;
- return;
- }
-}
-
-static void sppp_channel_delete(struct channel_data *chan)
-{
- unregister_netdev(chan->pppdev.dev);
- sppp_detach(chan->pppdev.dev);
- free_netdev(chan->pppdev.dev);
- chan->pppdev.dev = NULL;
+ if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
+ return 0;
+ return -EINVAL;
}
-static int cosa_sppp_open(struct net_device *d)
+static int cosa_net_open(struct net_device *dev)
{
- struct channel_data *chan = d->ml_priv;
+ struct channel_data *chan = dev_to_chan(dev);
int err;
unsigned long flags;
}
spin_lock_irqsave(&chan->cosa->lock, flags);
if (chan->usage != 0) {
- printk(KERN_WARNING "%s: sppp_open called with usage count %d\n",
- chan->name, chan->usage);
+ printk(KERN_WARNING "%s: cosa_net_open called with usage count"
+ " %d\n", chan->name, chan->usage);
spin_unlock_irqrestore(&chan->cosa->lock, flags);
return -EBUSY;
}
- chan->setup_rx = sppp_setup_rx;
- chan->tx_done = sppp_tx_done;
- chan->rx_done = sppp_rx_done;
- chan->usage=-1;
+ chan->setup_rx = cosa_net_setup_rx;
+ chan->tx_done = cosa_net_tx_done;
+ chan->rx_done = cosa_net_rx_done;
+ chan->usage = -1;
chan->cosa->usage++;
spin_unlock_irqrestore(&chan->cosa->lock, flags);
- err = sppp_open(d);
+ err = hdlc_open(dev);
if (err) {
spin_lock_irqsave(&chan->cosa->lock, flags);
- chan->usage=0;
+ chan->usage = 0;
chan->cosa->usage--;
-
spin_unlock_irqrestore(&chan->cosa->lock, flags);
return err;
}
- netif_start_queue(d);
+ netif_start_queue(dev);
cosa_enable_rx(chan);
return 0;
}
-static int cosa_sppp_tx(struct sk_buff *skb, struct net_device *dev)
+static int cosa_net_tx(struct sk_buff *skb, struct net_device *dev)
{
- struct channel_data *chan = dev->ml_priv;
+ struct channel_data *chan = dev_to_chan(dev);
netif_stop_queue(dev);
return 0;
}
-static void cosa_sppp_timeout(struct net_device *dev)
+static void cosa_net_timeout(struct net_device *dev)
{
- struct channel_data *chan = dev->ml_priv;
+ struct channel_data *chan = dev_to_chan(dev);
if (test_bit(RXBIT, &chan->cosa->rxtx)) {
- chan->stats.rx_errors++;
- chan->stats.rx_missed_errors++;
+ chan->netdev->stats.rx_errors++;
+ chan->netdev->stats.rx_missed_errors++;
} else {
- chan->stats.tx_errors++;
- chan->stats.tx_aborted_errors++;
+ chan->netdev->stats.tx_errors++;
+ chan->netdev->stats.tx_aborted_errors++;
}
cosa_kick(chan->cosa);
if (chan->tx_skb) {
netif_wake_queue(dev);
}
-static int cosa_sppp_close(struct net_device *d)
+static int cosa_net_close(struct net_device *dev)
{
- struct channel_data *chan = d->ml_priv;
+ struct channel_data *chan = dev_to_chan(dev);
unsigned long flags;
- netif_stop_queue(d);
- sppp_close(d);
+ netif_stop_queue(dev);
+ hdlc_close(dev);
cosa_disable_rx(chan);
spin_lock_irqsave(&chan->cosa->lock, flags);
if (chan->rx_skb) {
kfree_skb(chan->tx_skb);
chan->tx_skb = NULL;
}
- chan->usage=0;
+ chan->usage = 0;
chan->cosa->usage--;
spin_unlock_irqrestore(&chan->cosa->lock, flags);
return 0;
}
-static char *sppp_setup_rx(struct channel_data *chan, int size)
+static char *cosa_net_setup_rx(struct channel_data *chan, int size)
{
/*
* We can safely fall back to non-dma-able memory, because we have
if (chan->rx_skb == NULL) {
printk(KERN_NOTICE "%s: Memory squeeze, dropping packet\n",
chan->name);
- chan->stats.rx_dropped++;
+ chan->netdev->stats.rx_dropped++;
return NULL;
}
- chan->pppdev.dev->trans_start = jiffies;
+ chan->netdev->trans_start = jiffies;
return skb_put(chan->rx_skb, size);
}
-static int sppp_rx_done(struct channel_data *chan)
+static int cosa_net_rx_done(struct channel_data *chan)
{
if (!chan->rx_skb) {
printk(KERN_WARNING "%s: rx_done with empty skb!\n",
chan->name);
- chan->stats.rx_errors++;
- chan->stats.rx_frame_errors++;
+ chan->netdev->stats.rx_errors++;
+ chan->netdev->stats.rx_frame_errors++;
return 0;
}
- chan->rx_skb->protocol = htons(ETH_P_WAN_PPP);
- chan->rx_skb->dev = chan->pppdev.dev;
+ chan->rx_skb->protocol = hdlc_type_trans(chan->rx_skb, chan->netdev);
+ chan->rx_skb->dev = chan->netdev;
skb_reset_mac_header(chan->rx_skb);
- chan->stats.rx_packets++;
- chan->stats.rx_bytes += chan->cosa->rxsize;
+ chan->netdev->stats.rx_packets++;
+ chan->netdev->stats.rx_bytes += chan->cosa->rxsize;
netif_rx(chan->rx_skb);
chan->rx_skb = NULL;
- chan->pppdev.dev->last_rx = jiffies;
+ chan->netdev->last_rx = jiffies;
return 0;
}
/* ARGSUSED */
-static int sppp_tx_done(struct channel_data *chan, int size)
+static int cosa_net_tx_done(struct channel_data *chan, int size)
{
if (!chan->tx_skb) {
printk(KERN_WARNING "%s: tx_done with empty skb!\n",
chan->name);
- chan->stats.tx_errors++;
- chan->stats.tx_aborted_errors++;
+ chan->netdev->stats.tx_errors++;
+ chan->netdev->stats.tx_aborted_errors++;
return 1;
}
dev_kfree_skb_irq(chan->tx_skb);
chan->tx_skb = NULL;
- chan->stats.tx_packets++;
- chan->stats.tx_bytes += size;
- netif_wake_queue(chan->pppdev.dev);
+ chan->netdev->stats.tx_packets++;
+ chan->netdev->stats.tx_bytes += size;
+ netif_wake_queue(chan->netdev);
return 1;
}
-static struct net_device_stats *cosa_net_stats(struct net_device *dev)
-{
- struct channel_data *chan = dev->ml_priv;
- return &chan->stats;
-}
-
-\f
/*---------- Character device ---------- */
-static void chardev_channel_init(struct channel_data *chan)
-{
- mutex_init(&chan->rlock);
- init_MUTEX(&chan->wsem);
-}
-
static ssize_t cosa_read(struct file *file,
char __user *buf, size_t count, loff_t *ppos)
{
return -ENOIOCTLCMD;
}
-static int cosa_sppp_ioctl(struct net_device *dev, struct ifreq *ifr,
- int cmd)
+static int cosa_net_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
int rv;
- struct channel_data *chan = dev->ml_priv;
- rv = cosa_ioctl_common(chan->cosa, chan, cmd, (unsigned long)ifr->ifr_data);
- if (rv == -ENOIOCTLCMD) {
- return sppp_do_ioctl(dev, ifr, cmd);
- }
- return rv;
+ struct channel_data *chan = dev_to_chan(dev);
+ rv = cosa_ioctl_common(chan->cosa, chan, cmd,
+ (unsigned long)ifr->ifr_data);
+ if (rv != -ENOIOCTLCMD)
+ return rv;
+ return hdlc_ioctl(dev, ifr, cmd);
}
static int cosa_chardev_ioctl(struct inode *inode, struct file *file,
#include <linux/netdevice.h>
#include <linux/skbuff.h>
#include <linux/delay.h>
-#include <net/syncppp.h>
#include <linux/hdlc.h>
#include <linux/mutex.h>
/* Default parameters for the link
*/
#define FST_TX_QUEUE_LEN 100 /* At 8Mbps a longer queue length is
- * useful, the syncppp module forces
- * this down assuming a slower line I
- * guess.
- */
+ * useful */
#define FST_TXQ_DEPTH 16 /* This one is for the buffering
* of frames on the way down to the card
* so that we can keep the card busy
/* Ioctl call command values
- *
- * The first three private ioctls are used by the sync-PPP module,
- * allowing a little room for expansion we start our numbering at 10.
*/
#define FSTWRITE (SIOCDEVPRIVATE+10)
#define FSTCPURESET (SIOCDEVPRIVATE+11)
#define J1 7
/* "proto" */
-#define FST_HDLC 1 /* Cisco compatible HDLC */
-#define FST_PPP 2 /* Sync PPP */
-#define FST_MONITOR 3 /* Monitor only (raw packet reception) */
#define FST_RAW 4 /* Two way raw packets */
#define FST_GEN_HDLC 5 /* Using "Generic HDLC" module */
* - proto->start() and stop() are called with spin_lock_irq held.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/notifier.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/notifier.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
#include <net/net_namespace.h>
if (dev->get_stats != hdlc_get_stats)
return NOTIFY_DONE; /* not an HDLC device */
-
+
if (event != NETDEV_CHANGE)
return NOTIFY_DONE; /* Only interrested in carrier changes */
static struct notifier_block hdlc_notifier = {
- .notifier_call = hdlc_device_event,
+ .notifier_call = hdlc_device_event,
};
printk(KERN_INFO "%s\n", version);
if ((result = register_netdevice_notifier(&hdlc_notifier)) != 0)
- return result;
- dev_add_pack(&hdlc_packet_type);
+ return result;
+ dev_add_pack(&hdlc_packet_type);
return 0;
}
* as published by the Free Software Foundation.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
#undef DEBUG_HARD_HEADER
static int cisco_ioctl(struct net_device *dev, struct ifreq *ifr);
-static inline struct cisco_state * state(hdlc_device *hdlc)
+static inline struct cisco_state* state(hdlc_device *hdlc)
{
- return(struct cisco_state *)(hdlc->state);
+ return (struct cisco_state *)hdlc->state;
}
data->address != CISCO_UNICAST)
goto rx_error;
- switch(ntohs(data->protocol)) {
+ switch (ntohs(data->protocol)) {
case CISCO_SYS_INFO:
/* Packet is not needed, drop it. */
dev_kfree_skb_any(skb);
static const struct header_ops cisco_header_ops = {
.create = cisco_hard_header,
};
-
+
static int cisco_ioctl(struct net_device *dev, struct ifreq *ifr)
{
cisco_proto __user *cisco_s = ifr->ifr_settings.ifs_ifsu.cisco;
return 0;
case IF_PROTO_CISCO:
- if(!capable(CAP_NET_ADMIN))
+ if (!capable(CAP_NET_ADMIN))
return -EPERM;
- if(dev->flags & IFF_UP)
+ if (dev->flags & IFF_UP)
return -EBUSY;
if (copy_from_user(&new_settings, cisco_s, size))
new_settings.timeout < 2)
return -EINVAL;
- result=hdlc->attach(dev, ENCODING_NRZ,PARITY_CRC16_PR1_CCITT);
+ result = hdlc->attach(dev, ENCODING_NRZ,PARITY_CRC16_PR1_CCITT);
if (result)
return result;
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/etherdevice.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/etherdevice.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
#undef DEBUG_PKT
#undef DEBUG_ECN
unsigned ea1: 1;
unsigned cr: 1;
unsigned dlcih: 6;
-
+
unsigned ea2: 1;
unsigned de: 1;
unsigned becn: 1;
* as published by the Free Software Foundation.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
#include <net/syncppp.h>
struct ppp_state {
* as published by the Free Software Foundation.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
static int raw_ioctl(struct net_device *dev, struct ifreq *ifr);
* as published by the Free Software Foundation.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/etherdevice.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
+#include <linux/inetdevice.h>
#include <linux/init.h>
-#include <linux/skbuff.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pkt_sched.h>
-#include <linux/inetdevice.h>
-#include <linux/lapb.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/etherdevice.h>
-#include <linux/hdlc.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
static int raw_eth_ioctl(struct net_device *dev, struct ifreq *ifr);
* as published by the Free Software Foundation.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/poll.h>
#include <linux/errno.h>
+#include <linux/hdlc.h>
#include <linux/if_arp.h>
-#include <linux/init.h>
-#include <linux/skbuff.h>
-#include <linux/pkt_sched.h>
#include <linux/inetdevice.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
#include <linux/lapb.h>
+#include <linux/module.h>
+#include <linux/pkt_sched.h>
+#include <linux/poll.h>
#include <linux/rtnetlink.h>
-#include <linux/hdlc.h>
-
+#include <linux/skbuff.h>
+#include <linux/slab.h>
#include <net/x25device.h>
static int x25_ioctl(struct net_device *dev, struct ifreq *ifr);
* touching control registers.
*
* Port B isnt wired (why - beats me)
+ *
+ * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
*/
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/if_arp.h>
#include <linux/delay.h>
+#include <linux/hdlc.h>
#include <linux/ioport.h>
#include <net/arp.h>
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/byteorder.h>
-#include <net/syncppp.h>
#include "z85230.h"
static int dma;
-struct sv11_device
-{
- void *if_ptr; /* General purpose pointer (used by SPPP) */
- struct z8530_dev sync;
- struct ppp_device netdev;
-};
-
/*
* Network driver support routines
*/
+static inline struct z8530_dev* dev_to_sv(struct net_device *dev)
+{
+ return (struct z8530_dev *)dev_to_hdlc(dev)->priv;
+}
+
/*
- * Frame receive. Simple for our card as we do sync ppp and there
+ * Frame receive. Simple for our card as we do HDLC and there
* is no funny garbage involved
*/
-
+
static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
{
/* Drop the CRC - it's not a good idea to try and negotiate it ;) */
- skb_trim(skb, skb->len-2);
- skb->protocol=__constant_htons(ETH_P_WAN_PPP);
+ skb_trim(skb, skb->len - 2);
+ skb->protocol = hdlc_type_trans(skb, c->netdevice);
skb_reset_mac_header(skb);
- skb->dev=c->netdevice;
+ skb->dev = c->netdevice;
/*
* Send it to the PPP layer. We don't have time to process
* it right now.
netif_rx(skb);
c->netdevice->last_rx = jiffies;
}
-
+
/*
* We've been placed in the UP state
- */
-
+ */
+
static int hostess_open(struct net_device *d)
{
- struct sv11_device *sv11=d->ml_priv;
+ struct z8530_dev *sv11 = dev_to_sv(d);
int err = -1;
-
+
/*
* Link layer up
*/
- switch(dma)
- {
+ switch (dma) {
case 0:
- err=z8530_sync_open(d, &sv11->sync.chanA);
+ err = z8530_sync_open(d, &sv11->chanA);
break;
case 1:
- err=z8530_sync_dma_open(d, &sv11->sync.chanA);
+ err = z8530_sync_dma_open(d, &sv11->chanA);
break;
case 2:
- err=z8530_sync_txdma_open(d, &sv11->sync.chanA);
+ err = z8530_sync_txdma_open(d, &sv11->chanA);
break;
}
-
- if(err)
+
+ if (err)
return err;
- /*
- * Begin PPP
- */
- err=sppp_open(d);
- if(err)
- {
- switch(dma)
- {
+
+ err = hdlc_open(d);
+ if (err) {
+ switch (dma) {
case 0:
- z8530_sync_close(d, &sv11->sync.chanA);
+ z8530_sync_close(d, &sv11->chanA);
break;
case 1:
- z8530_sync_dma_close(d, &sv11->sync.chanA);
+ z8530_sync_dma_close(d, &sv11->chanA);
break;
case 2:
- z8530_sync_txdma_close(d, &sv11->sync.chanA);
+ z8530_sync_txdma_close(d, &sv11->chanA);
break;
- }
+ }
return err;
}
- sv11->sync.chanA.rx_function=hostess_input;
-
+ sv11->chanA.rx_function = hostess_input;
+
/*
* Go go go
*/
static int hostess_close(struct net_device *d)
{
- struct sv11_device *sv11=d->ml_priv;
+ struct z8530_dev *sv11 = dev_to_sv(d);
/*
* Discard new frames
*/
- sv11->sync.chanA.rx_function=z8530_null_rx;
- /*
- * PPP off
- */
- sppp_close(d);
- /*
- * Link layer down
- */
+ sv11->chanA.rx_function = z8530_null_rx;
+
+ hdlc_close(d);
netif_stop_queue(d);
-
- switch(dma)
- {
+
+ switch (dma) {
case 0:
- z8530_sync_close(d, &sv11->sync.chanA);
+ z8530_sync_close(d, &sv11->chanA);
break;
case 1:
- z8530_sync_dma_close(d, &sv11->sync.chanA);
+ z8530_sync_dma_close(d, &sv11->chanA);
break;
case 2:
- z8530_sync_txdma_close(d, &sv11->sync.chanA);
+ z8530_sync_txdma_close(d, &sv11->chanA);
break;
}
return 0;
static int hostess_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
{
- /* struct sv11_device *sv11=d->ml_priv;
- z8530_ioctl(d,&sv11->sync.chanA,ifr,cmd) */
- return sppp_do_ioctl(d, ifr,cmd);
-}
-
-static struct net_device_stats *hostess_get_stats(struct net_device *d)
-{
- struct sv11_device *sv11=d->ml_priv;
- if(sv11)
- return z8530_get_stats(&sv11->sync.chanA);
- else
- return NULL;
+ /* struct z8530_dev *sv11=dev_to_sv(d);
+ z8530_ioctl(d,&sv11->chanA,ifr,cmd) */
+ return hdlc_ioctl(d, ifr, cmd);
}
/*
- * Passed PPP frames, fire them downwind.
+ * Passed network frames, fire them downwind.
*/
-
+
static int hostess_queue_xmit(struct sk_buff *skb, struct net_device *d)
{
- struct sv11_device *sv11=d->ml_priv;
- return z8530_queue_xmit(&sv11->sync.chanA, skb);
+ return z8530_queue_xmit(&dev_to_sv(d)->chanA, skb);
}
-static int hostess_neigh_setup(struct neighbour *n)
+static int hostess_attach(struct net_device *dev, unsigned short encoding,
+ unsigned short parity)
{
- if (n->nud_state == NUD_NONE) {
- n->ops = &arp_broken_ops;
- n->output = n->ops->output;
- }
- return 0;
-}
-
-static int hostess_neigh_setup_dev(struct net_device *dev, struct neigh_parms *p)
-{
- if (p->tbl->family == AF_INET) {
- p->neigh_setup = hostess_neigh_setup;
- p->ucast_probes = 0;
- p->mcast_probes = 0;
- }
- return 0;
-}
-
-static void sv11_setup(struct net_device *dev)
-{
- dev->open = hostess_open;
- dev->stop = hostess_close;
- dev->hard_start_xmit = hostess_queue_xmit;
- dev->get_stats = hostess_get_stats;
- dev->do_ioctl = hostess_ioctl;
- dev->neigh_setup = hostess_neigh_setup_dev;
+ if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
+ return 0;
+ return -EINVAL;
}
/*
* Description block for a Comtrol Hostess SV11 card
*/
-
-static struct sv11_device *sv11_init(int iobase, int irq)
+
+static struct z8530_dev *sv11_init(int iobase, int irq)
{
- struct z8530_dev *dev;
- struct sv11_device *sv;
-
+ struct z8530_dev *sv;
+ struct net_device *netdev;
/*
* Get the needed I/O space
*/
-
- if(!request_region(iobase, 8, "Comtrol SV11"))
- {
- printk(KERN_WARNING "hostess: I/O 0x%X already in use.\n", iobase);
+
+ if (!request_region(iobase, 8, "Comtrol SV11")) {
+ printk(KERN_WARNING "hostess: I/O 0x%X already in use.\n",
+ iobase);
return NULL;
}
-
- sv = kzalloc(sizeof(struct sv11_device), GFP_KERNEL);
- if(!sv)
- goto fail3;
-
- sv->if_ptr=&sv->netdev;
-
- sv->netdev.dev = alloc_netdev(0, "hdlc%d", sv11_setup);
- if(!sv->netdev.dev)
- goto fail2;
-
- dev=&sv->sync;
-
+
+ sv = kzalloc(sizeof(struct z8530_dev), GFP_KERNEL);
+ if (!sv)
+ goto err_kzalloc;
+
/*
* Stuff in the I/O addressing
*/
-
- dev->active = 0;
-
- dev->chanA.ctrlio=iobase+1;
- dev->chanA.dataio=iobase+3;
- dev->chanB.ctrlio=-1;
- dev->chanB.dataio=-1;
- dev->chanA.irqs=&z8530_nop;
- dev->chanB.irqs=&z8530_nop;
-
- outb(0, iobase+4); /* DMA off */
-
+
+ sv->active = 0;
+
+ sv->chanA.ctrlio = iobase + 1;
+ sv->chanA.dataio = iobase + 3;
+ sv->chanB.ctrlio = -1;
+ sv->chanB.dataio = -1;
+ sv->chanA.irqs = &z8530_nop;
+ sv->chanB.irqs = &z8530_nop;
+
+ outb(0, iobase + 4); /* DMA off */
+
/* We want a fast IRQ for this device. Actually we'd like an even faster
IRQ ;) - This is one driver RtLinux is made for */
-
- if(request_irq(irq, &z8530_interrupt, IRQF_DISABLED, "Hostess SV11", dev)<0)
- {
+
+ if (request_irq(irq, &z8530_interrupt, IRQF_DISABLED,
+ "Hostess SV11", sv) < 0) {
printk(KERN_WARNING "hostess: IRQ %d already in use.\n", irq);
- goto fail1;
+ goto err_irq;
}
-
- dev->irq=irq;
- dev->chanA.private=sv;
- dev->chanA.netdevice=sv->netdev.dev;
- dev->chanA.dev=dev;
- dev->chanB.dev=dev;
-
- if(dma)
- {
+
+ sv->irq = irq;
+ sv->chanA.private = sv;
+ sv->chanA.dev = sv;
+ sv->chanB.dev = sv;
+
+ if (dma) {
/*
* You can have DMA off or 1 and 3 thats the lot
* on the Comtrol.
*/
- dev->chanA.txdma=3;
- dev->chanA.rxdma=1;
- outb(0x03|0x08, iobase+4); /* DMA on */
- if(request_dma(dev->chanA.txdma, "Hostess SV/11 (TX)")!=0)
- goto fail;
-
- if(dma==1)
- {
- if(request_dma(dev->chanA.rxdma, "Hostess SV/11 (RX)")!=0)
- goto dmafail;
- }
+ sv->chanA.txdma = 3;
+ sv->chanA.rxdma = 1;
+ outb(0x03 | 0x08, iobase + 4); /* DMA on */
+ if (request_dma(sv->chanA.txdma, "Hostess SV/11 (TX)"))
+ goto err_txdma;
+
+ if (dma == 1)
+ if (request_dma(sv->chanA.rxdma, "Hostess SV/11 (RX)"))
+ goto err_rxdma;
}
/* Kill our private IRQ line the hostess can end up chattering
until the configuration is set */
disable_irq(irq);
-
+
/*
* Begin normal initialise
*/
-
- if(z8530_init(dev)!=0)
- {
+
+ if (z8530_init(sv)) {
printk(KERN_ERR "Z8530 series device not found.\n");
enable_irq(irq);
- goto dmafail2;
+ goto free_dma;
}
- z8530_channel_load(&dev->chanB, z8530_dead_port);
- if(dev->type==Z85C30)
- z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream);
+ z8530_channel_load(&sv->chanB, z8530_dead_port);
+ if (sv->type == Z85C30)
+ z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream);
else
- z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream_85230);
-
+ z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream_85230);
+
enable_irq(irq);
-
/*
* Now we can take the IRQ
*/
- if(dev_alloc_name(dev->chanA.netdevice,"hdlc%d")>=0)
- {
- struct net_device *d=dev->chanA.netdevice;
- /*
- * Initialise the PPP components
- */
- d->ml_priv = sv;
- sppp_attach(&sv->netdev);
-
- /*
- * Local fields
- */
-
- d->base_addr = iobase;
- d->irq = irq;
-
- if(register_netdev(d))
- {
- printk(KERN_ERR "%s: unable to register device.\n",
- d->name);
- sppp_detach(d);
- goto dmafail2;
- }
+ sv->chanA.netdevice = netdev = alloc_hdlcdev(sv);
+ if (!netdev)
+ goto free_dma;
- z8530_describe(dev, "I/O", iobase);
- dev->active=1;
- return sv;
+ dev_to_hdlc(netdev)->attach = hostess_attach;
+ dev_to_hdlc(netdev)->xmit = hostess_queue_xmit;
+ netdev->open = hostess_open;
+ netdev->stop = hostess_close;
+ netdev->do_ioctl = hostess_ioctl;
+ netdev->base_addr = iobase;
+ netdev->irq = irq;
+
+ if (register_hdlc_device(netdev)) {
+ printk(KERN_ERR "hostess: unable to register HDLC device.\n");
+ free_netdev(netdev);
+ goto free_dma;
}
-dmafail2:
- if(dma==1)
- free_dma(dev->chanA.rxdma);
-dmafail:
- if(dma)
- free_dma(dev->chanA.txdma);
-fail:
- free_irq(irq, dev);
-fail1:
- free_netdev(sv->netdev.dev);
-fail2:
+
+ z8530_describe(sv, "I/O", iobase);
+ sv->active = 1;
+ return sv;
+
+free_dma:
+ if (dma == 1)
+ free_dma(sv->chanA.rxdma);
+err_rxdma:
+ if (dma)
+ free_dma(sv->chanA.txdma);
+err_txdma:
+ free_irq(irq, sv);
+err_irq:
kfree(sv);
-fail3:
- release_region(iobase,8);
+err_kzalloc:
+ release_region(iobase, 8);
return NULL;
}
-static void sv11_shutdown(struct sv11_device *dev)
+static void sv11_shutdown(struct z8530_dev *dev)
{
- sppp_detach(dev->netdev.dev);
- unregister_netdev(dev->netdev.dev);
- z8530_shutdown(&dev->sync);
- free_irq(dev->sync.irq, dev);
- if(dma)
- {
- if(dma==1)
- free_dma(dev->sync.chanA.rxdma);
- free_dma(dev->sync.chanA.txdma);
+ unregister_hdlc_device(dev->chanA.netdevice);
+ z8530_shutdown(dev);
+ free_irq(dev->irq, dev);
+ if (dma) {
+ if (dma == 1)
+ free_dma(dev->chanA.rxdma);
+ free_dma(dev->chanA.txdma);
}
- release_region(dev->sync.chanA.ctrlio-1, 8);
- free_netdev(dev->netdev.dev);
+ release_region(dev->chanA.ctrlio - 1, 8);
+ free_netdev(dev->chanA.netdevice);
kfree(dev);
}
-#ifdef MODULE
-
-static int io=0x200;
-static int irq=9;
+static int io = 0x200;
+static int irq = 9;
module_param(io, int, 0);
MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
-static struct sv11_device *sv11_unit;
+static struct z8530_dev *sv11_unit;
int init_module(void)
{
- printk(KERN_INFO "SV-11 Z85230 Synchronous Driver v 0.03.\n");
- printk(KERN_INFO "(c) Copyright 2001, Red Hat Inc.\n");
- if((sv11_unit=sv11_init(io,irq))==NULL)
+ if ((sv11_unit = sv11_init(io, irq)) == NULL)
return -ENODEV;
return 0;
}
void cleanup_module(void)
{
- if(sv11_unit)
+ if (sv11_unit)
sv11_shutdown(sv11_unit);
}
-
-#endif
-
devaddr, unsigned regno);
void lmc_mii_writereg(lmc_softc_t * const sc, unsigned devaddr,
unsigned regno, unsigned data);
-void lmc_led_on(lmc_softc_t * const, u_int32_t);
-void lmc_led_off(lmc_softc_t * const, u_int32_t);
+void lmc_led_on(lmc_softc_t * const, u32);
+void lmc_led_off(lmc_softc_t * const, u32);
unsigned lmc_mii_readreg(lmc_softc_t * const, unsigned, unsigned);
void lmc_mii_writereg(lmc_softc_t * const, unsigned, unsigned, unsigned);
-void lmc_gpio_mkinput(lmc_softc_t * const sc, u_int32_t bits);
-void lmc_gpio_mkoutput(lmc_softc_t * const sc, u_int32_t bits);
+void lmc_gpio_mkinput(lmc_softc_t * const sc, u32 bits);
+void lmc_gpio_mkoutput(lmc_softc_t * const sc, u32 bits);
int lmc_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
extern lmc_media_t lmc_hssi_media;
#ifdef _DBG_EVENTLOG
-static void lmcEventLog( u_int32_t EventNum, u_int32_t arg2, u_int32_t arg3 );
+static void lmcEventLog(u32 EventNum, u32 arg2, u32 arg3);
#endif
#endif
-
-
#include <linux/types.h>
#include <linux/netdevice.h>
#include <linux/interrupt.h>
#endif
#ifdef DEBUG
-u_int32_t lmcEventLogIndex = 0;
-u_int32_t lmcEventLogBuf[LMC_EVENTLOGSIZE * LMC_EVENTLOGARGS];
+u32 lmcEventLogIndex;
+u32 lmcEventLogBuf[LMC_EVENTLOGSIZE * LMC_EVENTLOGARGS];
-void lmcEventLog (u_int32_t EventNum, u_int32_t arg2, u_int32_t arg3)
+void lmcEventLog(u32 EventNum, u32 arg2, u32 arg3)
{
lmcEventLogBuf[lmcEventLogIndex++] = EventNum;
lmcEventLogBuf[lmcEventLogIndex++] = arg2;
#ifdef DEBUG
-extern u_int32_t lmcEventLogIndex;
-extern u_int32_t lmcEventLogBuf[LMC_EVENTLOGSIZE * LMC_EVENTLOGARGS];
+extern u32 lmcEventLogIndex;
+extern u32 lmcEventLogBuf[LMC_EVENTLOGSIZE * LMC_EVENTLOGARGS];
#define LMC_EVENT_LOG(x, y, z) lmcEventLog((x), (y), (z))
#else
#define LMC_EVENT_LOG(x,y,z)
#endif /* end ifdef _DBG_EVENTLOG */
void lmcConsoleLog(char *type, unsigned char *ucData, int iLen);
-void lmcEventLog (u_int32_t EventNum, u_int32_t arg2, u_int32_t arg3);
+void lmcEventLog(u32 EventNum, u32 arg2, u32 arg3);
void lmc_trace(struct net_device *dev, char *msg);
#endif
/*
* IFTYPE defines
*/
-#define LMC_PPP 1 /* use sppp interface */
+#define LMC_PPP 1 /* use generic HDLC interface */
#define LMC_NET 2 /* use direct net interface */
#define LMC_RAW 3 /* use direct net interface */
/*
* Copyright (c) 1997-2000 LAN Media Corporation (LMC)
* All rights reserved. www.lanmedia.com
+ * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
*
* This code is written by:
* Andrew Stanley-Jones (asj@cban.com)
*
*/
-/* $Id: lmc_main.c,v 1.36 2000/04/11 05:25:25 asj Exp $ */
-
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/delay.h>
+#include <linux/hdlc.h>
#include <linux/init.h>
#include <linux/in.h>
#include <linux/if_arp.h>
#include <linux/skbuff.h>
#include <linux/inet.h>
#include <linux/bitops.h>
-
-#include <net/syncppp.h>
-
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/io.h>
#include <asm/dma.h>
#include "lmc_debug.h"
#include "lmc_proto.h"
-static int lmc_first_load = 0;
-
static int LMC_PKT_BUF_SZ = 1542;
static struct pci_device_id lmc_pci_tbl[] = {
};
MODULE_DEVICE_TABLE(pci, lmc_pci_tbl);
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
-static int lmc_start_xmit(struct sk_buff *skb, struct net_device *dev);
static int lmc_start_xmit(struct sk_buff *skb, struct net_device *dev);
static int lmc_rx (struct net_device *dev);
static int lmc_open(struct net_device *dev);
* linux reserves 16 device specific IOCTLs. We call them
* LMCIOC* to control various bits of our world.
*/
-int lmc_ioctl (struct net_device *dev, struct ifreq *ifr, int cmd) /*fold00*/
+int lmc_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) /*fold00*/
{
- lmc_softc_t *sc;
+ lmc_softc_t *sc = dev_to_sc(dev);
lmc_ctl_t ctl;
- int ret;
- u_int16_t regVal;
+ int ret = -EOPNOTSUPP;
+ u16 regVal;
unsigned long flags;
- struct sppp *sp;
-
- ret = -EOPNOTSUPP;
-
- sc = dev->priv;
-
lmc_trace(dev, "lmc_ioctl in");
/*
break;
case LMCIOCSINFO: /*fold01*/
- sp = &((struct ppp_device *) dev)->sppp;
if (!capable(CAP_NET_ADMIN)) {
ret = -EPERM;
break;
sc->TxDescriptControlInit &= ~LMC_TDES_ADD_CRC_DISABLE;
}
- if (ctl.keepalive_onoff == LMC_CTL_OFF)
- sp->pp_flags &= ~PP_KEEPALIVE; /* Turn off */
- else
- sp->pp_flags |= PP_KEEPALIVE; /* Turn on */
-
ret = 0;
break;
case LMCIOCIFTYPE: /*fold01*/
{
- u_int16_t old_type = sc->if_type;
- u_int16_t new_type;
+ u16 old_type = sc->if_type;
+ u16 new_type;
if (!capable(CAP_NET_ADMIN)) {
ret = -EPERM;
break;
}
- if (copy_from_user(&new_type, ifr->ifr_data, sizeof(u_int16_t))) {
+ if (copy_from_user(&new_type, ifr->ifr_data, sizeof(u16))) {
ret = -EFAULT;
break;
}
}
lmc_proto_close(sc);
- lmc_proto_detach(sc);
sc->if_type = new_type;
-// lmc_proto_init(sc);
lmc_proto_attach(sc);
- lmc_proto_open(sc);
-
- ret = 0 ;
- break ;
+ ret = lmc_proto_open(sc);
+ break;
}
case LMCIOCGETXINFO: /*fold01*/
break;
- case LMCIOCGETLMCSTATS: /*fold01*/
- if (sc->lmc_cardtype == LMC_CARDTYPE_T1){
- lmc_mii_writereg (sc, 0, 17, T1FRAMER_FERR_LSB);
- sc->stats.framingBitErrorCount +=
- lmc_mii_readreg (sc, 0, 18) & 0xff;
- lmc_mii_writereg (sc, 0, 17, T1FRAMER_FERR_MSB);
- sc->stats.framingBitErrorCount +=
- (lmc_mii_readreg (sc, 0, 18) & 0xff) << 8;
- lmc_mii_writereg (sc, 0, 17, T1FRAMER_LCV_LSB);
- sc->stats.lineCodeViolationCount +=
- lmc_mii_readreg (sc, 0, 18) & 0xff;
- lmc_mii_writereg (sc, 0, 17, T1FRAMER_LCV_MSB);
- sc->stats.lineCodeViolationCount +=
- (lmc_mii_readreg (sc, 0, 18) & 0xff) << 8;
- lmc_mii_writereg (sc, 0, 17, T1FRAMER_AERR);
- regVal = lmc_mii_readreg (sc, 0, 18) & 0xff;
-
- sc->stats.lossOfFrameCount +=
- (regVal & T1FRAMER_LOF_MASK) >> 4;
- sc->stats.changeOfFrameAlignmentCount +=
- (regVal & T1FRAMER_COFA_MASK) >> 2;
- sc->stats.severelyErroredFrameCount +=
- regVal & T1FRAMER_SEF_MASK;
- }
-
- if (copy_to_user(ifr->ifr_data, &sc->stats,
- sizeof (struct lmc_statistics)))
- ret = -EFAULT;
- else
- ret = 0;
- break;
+ case LMCIOCGETLMCSTATS:
+ if (sc->lmc_cardtype == LMC_CARDTYPE_T1) {
+ lmc_mii_writereg(sc, 0, 17, T1FRAMER_FERR_LSB);
+ sc->extra_stats.framingBitErrorCount +=
+ lmc_mii_readreg(sc, 0, 18) & 0xff;
+ lmc_mii_writereg(sc, 0, 17, T1FRAMER_FERR_MSB);
+ sc->extra_stats.framingBitErrorCount +=
+ (lmc_mii_readreg(sc, 0, 18) & 0xff) << 8;
+ lmc_mii_writereg(sc, 0, 17, T1FRAMER_LCV_LSB);
+ sc->extra_stats.lineCodeViolationCount +=
+ lmc_mii_readreg(sc, 0, 18) & 0xff;
+ lmc_mii_writereg(sc, 0, 17, T1FRAMER_LCV_MSB);
+ sc->extra_stats.lineCodeViolationCount +=
+ (lmc_mii_readreg(sc, 0, 18) & 0xff) << 8;
+ lmc_mii_writereg(sc, 0, 17, T1FRAMER_AERR);
+ regVal = lmc_mii_readreg(sc, 0, 18) & 0xff;
+
+ sc->extra_stats.lossOfFrameCount +=
+ (regVal & T1FRAMER_LOF_MASK) >> 4;
+ sc->extra_stats.changeOfFrameAlignmentCount +=
+ (regVal & T1FRAMER_COFA_MASK) >> 2;
+ sc->extra_stats.severelyErroredFrameCount +=
+ regVal & T1FRAMER_SEF_MASK;
+ }
+ if (copy_to_user(ifr->ifr_data, &sc->lmc_device->stats,
+ sizeof(sc->lmc_device->stats)) ||
+ copy_to_user(ifr->ifr_data + sizeof(sc->lmc_device->stats),
+ &sc->extra_stats, sizeof(sc->extra_stats)))
+ ret = -EFAULT;
+ else
+ ret = 0;
+ break;
- case LMCIOCCLEARLMCSTATS: /*fold01*/
- if (!capable(CAP_NET_ADMIN)){
- ret = -EPERM;
- break;
- }
+ case LMCIOCCLEARLMCSTATS:
+ if (!capable(CAP_NET_ADMIN)) {
+ ret = -EPERM;
+ break;
+ }
- memset (&sc->stats, 0, sizeof (struct lmc_statistics));
- sc->stats.check = STATCHECK;
- sc->stats.version_size = (DRIVER_VERSION << 16) +
- sizeof (struct lmc_statistics);
- sc->stats.lmc_cardtype = sc->lmc_cardtype;
- ret = 0;
- break;
+ memset(&sc->lmc_device->stats, 0, sizeof(sc->lmc_device->stats));
+ memset(&sc->extra_stats, 0, sizeof(sc->extra_stats));
+ sc->extra_stats.check = STATCHECK;
+ sc->extra_stats.version_size = (DRIVER_VERSION << 16) +
+ sizeof(sc->lmc_device->stats) + sizeof(sc->extra_stats);
+ sc->extra_stats.lmc_cardtype = sc->lmc_cardtype;
+ ret = 0;
+ break;
case LMCIOCSETCIRCUIT: /*fold01*/
if (!capable(CAP_NET_ADMIN)){
ret = -EFAULT;
break;
}
- if (copy_to_user(ifr->ifr_data + sizeof (u32), lmcEventLogBuf, sizeof (lmcEventLogBuf)))
+ if (copy_to_user(ifr->ifr_data + sizeof(u32), lmcEventLogBuf,
+ sizeof(lmcEventLogBuf)))
ret = -EFAULT;
else
ret = 0;
/* the watchdog process that cruises around */
static void lmc_watchdog (unsigned long data) /*fold00*/
{
- struct net_device *dev = (struct net_device *) data;
- lmc_softc_t *sc;
+ struct net_device *dev = (struct net_device *)data;
+ lmc_softc_t *sc = dev_to_sc(dev);
int link_status;
- u_int32_t ticks;
+ u32 ticks;
unsigned long flags;
- sc = dev->priv;
-
lmc_trace(dev, "lmc_watchdog in");
spin_lock_irqsave(&sc->lmc_lock, flags);
* check for a transmit interrupt timeout
* Has the packet xmt vs xmt serviced threshold been exceeded */
if (sc->lmc_taint_tx == sc->lastlmc_taint_tx &&
- sc->stats.tx_packets > sc->lasttx_packets &&
- sc->tx_TimeoutInd == 0)
+ sc->lmc_device->stats.tx_packets > sc->lasttx_packets &&
+ sc->tx_TimeoutInd == 0)
{
/* wait for the watchdog to come around again */
sc->tx_TimeoutInd = 1;
}
else if (sc->lmc_taint_tx == sc->lastlmc_taint_tx &&
- sc->stats.tx_packets > sc->lasttx_packets &&
- sc->tx_TimeoutInd)
+ sc->lmc_device->stats.tx_packets > sc->lasttx_packets &&
+ sc->tx_TimeoutInd)
{
LMC_EVENT_LOG(LMC_EVENT_XMTINTTMO, LMC_CSR_READ (sc, csr_status), 0);
sc->tx_TimeoutDisplay = 1;
- sc->stats.tx_TimeoutCnt++;
+ sc->extra_stats.tx_TimeoutCnt++;
/* DEC chip is stuck, hit it with a RESET!!!! */
lmc_running_reset (dev);
/* reset the transmit timeout detection flag */
sc->tx_TimeoutInd = 0;
sc->lastlmc_taint_tx = sc->lmc_taint_tx;
- sc->lasttx_packets = sc->stats.tx_packets;
- }
- else
- {
+ sc->lasttx_packets = sc->lmc_device->stats.tx_packets;
+ } else {
sc->tx_TimeoutInd = 0;
sc->lastlmc_taint_tx = sc->lmc_taint_tx;
- sc->lasttx_packets = sc->stats.tx_packets;
+ sc->lasttx_packets = sc->lmc_device->stats.tx_packets;
}
/* --- end time out check ----------------------------------- */
sc->last_link_status = 1;
/* lmc_reset (sc); Again why reset??? */
- /* Inform the world that link protocol is back up. */
netif_carrier_on(dev);
-
- /* Now we have to tell the syncppp that we had an outage
- * and that it should deal. Calling sppp_reopen here
- * should do the trick, but we may have to call sppp_close
- * when the link goes down, and call sppp_open here.
- * Subject to more testing.
- * --bbraun
- */
-
- lmc_proto_reopen(sc);
-
}
/* Call media specific watchdog functions */
}
-static void lmc_setup(struct net_device * const dev) /*fold00*/
+static int lmc_attach(struct net_device *dev, unsigned short encoding,
+ unsigned short parity)
{
- lmc_trace(dev, "lmc_setup in");
-
- dev->type = ARPHRD_HDLC;
- dev->hard_start_xmit = lmc_start_xmit;
- dev->open = lmc_open;
- dev->stop = lmc_close;
- dev->get_stats = lmc_get_stats;
- dev->do_ioctl = lmc_ioctl;
- dev->tx_timeout = lmc_driver_timeout;
- dev->watchdog_timeo = (HZ); /* 1 second */
-
- lmc_trace(dev, "lmc_setup out");
+ if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
+ return 0;
+ return -EINVAL;
}
-
static int __devinit lmc_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
- struct net_device *dev;
- lmc_softc_t *sc;
- u16 subdevice;
- u_int16_t AdapModelNum;
- int err = -ENOMEM;
- static int cards_found;
-#ifndef GCOM
- /* We name by type not by vendor */
- static const char lmcname[] = "hdlc%d";
-#else
- /*
- * GCOM uses LMC vendor name so that clients can know which card
- * to attach to.
- */
- static const char lmcname[] = "lmc%d";
-#endif
-
-
- /*
- * Allocate our own device structure
- */
- dev = alloc_netdev(sizeof(lmc_softc_t), lmcname, lmc_setup);
- if (!dev) {
- printk (KERN_ERR "lmc:alloc_netdev for device failed\n");
- goto out1;
- }
-
- lmc_trace(dev, "lmc_init_one in");
-
- err = pci_enable_device(pdev);
- if (err) {
- printk(KERN_ERR "lmc: pci enable failed:%d\n", err);
- goto out2;
- }
-
- if (pci_request_regions(pdev, "lmc")) {
- printk(KERN_ERR "lmc: pci_request_region failed\n");
- err = -EIO;
- goto out3;
- }
-
- pci_set_drvdata(pdev, dev);
-
- if(lmc_first_load == 0){
- printk(KERN_INFO "Lan Media Corporation WAN Driver Version %d.%d.%d\n",
- DRIVER_MAJOR_VERSION, DRIVER_MINOR_VERSION,DRIVER_SUB_VERSION);
- lmc_first_load = 1;
- }
-
- sc = dev->priv;
- sc->lmc_device = dev;
- sc->name = dev->name;
-
- /* Initialize the sppp layer */
- /* An ioctl can cause a subsequent detach for raw frame interface */
- dev->ml_priv = sc;
- sc->if_type = LMC_PPP;
- sc->check = 0xBEAFCAFE;
- dev->base_addr = pci_resource_start(pdev, 0);
- dev->irq = pdev->irq;
-
- SET_NETDEV_DEV(dev, &pdev->dev);
-
- /*
- * This will get the protocol layer ready and do any 1 time init's
- * Must have a valid sc and dev structure
- */
- lmc_proto_init(sc);
-
- lmc_proto_attach(sc);
+ lmc_softc_t *sc;
+ struct net_device *dev;
+ u16 subdevice;
+ u16 AdapModelNum;
+ int err;
+ static int cards_found;
+
+ /* lmc_trace(dev, "lmc_init_one in"); */
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ printk(KERN_ERR "lmc: pci enable failed: %d\n", err);
+ return err;
+ }
- /*
- * Why were we changing this???
- dev->tx_queue_len = 100;
- */
+ err = pci_request_regions(pdev, "lmc");
+ if (err) {
+ printk(KERN_ERR "lmc: pci_request_region failed\n");
+ goto err_req_io;
+ }
- /* Init the spin lock so can call it latter */
+ /*
+ * Allocate our own device structure
+ */
+ sc = kzalloc(sizeof(lmc_softc_t), GFP_KERNEL);
+ if (!sc) {
+ err = -ENOMEM;
+ goto err_kzalloc;
+ }
- spin_lock_init(&sc->lmc_lock);
- pci_set_master(pdev);
+ dev = alloc_hdlcdev(sc);
+ if (!dev) {
+ printk(KERN_ERR "lmc:alloc_netdev for device failed\n");
+ goto err_hdlcdev;
+ }
- printk ("%s: detected at %lx, irq %d\n", dev->name,
- dev->base_addr, dev->irq);
- if (register_netdev (dev) != 0) {
- printk (KERN_ERR "%s: register_netdev failed.\n", dev->name);
- goto out4;
- }
+ dev->type = ARPHRD_HDLC;
+ dev_to_hdlc(dev)->xmit = lmc_start_xmit;
+ dev_to_hdlc(dev)->attach = lmc_attach;
+ dev->open = lmc_open;
+ dev->stop = lmc_close;
+ dev->get_stats = lmc_get_stats;
+ dev->do_ioctl = lmc_ioctl;
+ dev->tx_timeout = lmc_driver_timeout;
+ dev->watchdog_timeo = HZ; /* 1 second */
+ dev->tx_queue_len = 100;
+ sc->lmc_device = dev;
+ sc->name = dev->name;
+ sc->if_type = LMC_PPP;
+ sc->check = 0xBEAFCAFE;
+ dev->base_addr = pci_resource_start(pdev, 0);
+ dev->irq = pdev->irq;
+ pci_set_drvdata(pdev, dev);
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ /*
+ * This will get the protocol layer ready and do any 1 time init's
+ * Must have a valid sc and dev structure
+ */
+ lmc_proto_attach(sc);
+
+ /* Init the spin lock so can call it latter */
+
+ spin_lock_init(&sc->lmc_lock);
+ pci_set_master(pdev);
+
+ printk(KERN_INFO "%s: detected at %lx, irq %d\n", dev->name,
+ dev->base_addr, dev->irq);
+
+ err = register_hdlc_device(dev);
+ if (err) {
+ printk(KERN_ERR "%s: register_netdev failed.\n", dev->name);
+ free_netdev(dev);
+ goto err_hdlcdev;
+ }
sc->lmc_cardtype = LMC_CARDTYPE_UNKNOWN;
sc->lmc_timing = LMC_CTL_CLOCK_SOURCE_EXT;
switch (subdevice) {
case PCI_DEVICE_ID_LMC_HSSI:
- printk ("%s: LMC HSSI\n", dev->name);
+ printk(KERN_INFO "%s: LMC HSSI\n", dev->name);
sc->lmc_cardtype = LMC_CARDTYPE_HSSI;
sc->lmc_media = &lmc_hssi_media;
break;
case PCI_DEVICE_ID_LMC_DS3:
- printk ("%s: LMC DS3\n", dev->name);
+ printk(KERN_INFO "%s: LMC DS3\n", dev->name);
sc->lmc_cardtype = LMC_CARDTYPE_DS3;
sc->lmc_media = &lmc_ds3_media;
break;
case PCI_DEVICE_ID_LMC_SSI:
- printk ("%s: LMC SSI\n", dev->name);
+ printk(KERN_INFO "%s: LMC SSI\n", dev->name);
sc->lmc_cardtype = LMC_CARDTYPE_SSI;
sc->lmc_media = &lmc_ssi_media;
break;
case PCI_DEVICE_ID_LMC_T1:
- printk ("%s: LMC T1\n", dev->name);
+ printk(KERN_INFO "%s: LMC T1\n", dev->name);
sc->lmc_cardtype = LMC_CARDTYPE_T1;
sc->lmc_media = &lmc_t1_media;
break;
default:
- printk (KERN_WARNING "%s: LMC UNKOWN CARD!\n", dev->name);
+ printk(KERN_WARNING "%s: LMC UNKOWN CARD!\n", dev->name);
break;
}
*/
AdapModelNum = (lmc_mii_readreg (sc, 0, 3) & 0x3f0) >> 4;
- if ((AdapModelNum == LMC_ADAP_T1
- && subdevice == PCI_DEVICE_ID_LMC_T1) || /* detect LMC1200 */
- (AdapModelNum == LMC_ADAP_SSI
- && subdevice == PCI_DEVICE_ID_LMC_SSI) || /* detect LMC1000 */
- (AdapModelNum == LMC_ADAP_DS3
- && subdevice == PCI_DEVICE_ID_LMC_DS3) || /* detect LMC5245 */
- (AdapModelNum == LMC_ADAP_HSSI
- && subdevice == PCI_DEVICE_ID_LMC_HSSI))
- { /* detect LMC5200 */
+ if ((AdapModelNum != LMC_ADAP_T1 || /* detect LMC1200 */
+ subdevice != PCI_DEVICE_ID_LMC_T1) &&
+ (AdapModelNum != LMC_ADAP_SSI || /* detect LMC1000 */
+ subdevice != PCI_DEVICE_ID_LMC_SSI) &&
+ (AdapModelNum != LMC_ADAP_DS3 || /* detect LMC5245 */
+ subdevice != PCI_DEVICE_ID_LMC_DS3) &&
+ (AdapModelNum != LMC_ADAP_HSSI || /* detect LMC5200 */
+ subdevice != PCI_DEVICE_ID_LMC_HSSI))
+ printk(KERN_WARNING "%s: Model number (%d) miscompare for PCI"
+ " Subsystem ID = 0x%04x\n",
+ dev->name, AdapModelNum, subdevice);
- }
- else {
- printk ("%s: Model number (%d) miscompare for PCI Subsystem ID = 0x%04x\n",
- dev->name, AdapModelNum, subdevice);
-// return (NULL);
- }
/*
* reset clock
*/
LMC_CSR_WRITE (sc, csr_gp_timer, 0xFFFFFFFFUL);
sc->board_idx = cards_found++;
- sc->stats.check = STATCHECK;
- sc->stats.version_size = (DRIVER_VERSION << 16) +
- sizeof (struct lmc_statistics);
- sc->stats.lmc_cardtype = sc->lmc_cardtype;
+ sc->extra_stats.check = STATCHECK;
+ sc->extra_stats.version_size = (DRIVER_VERSION << 16) +
+ sizeof(sc->lmc_device->stats) + sizeof(sc->extra_stats);
+ sc->extra_stats.lmc_cardtype = sc->lmc_cardtype;
sc->lmc_ok = 0;
sc->last_link_status = 0;
lmc_trace(dev, "lmc_init_one out");
return 0;
- out4:
- lmc_proto_detach(sc);
- out3:
- if (pdev) {
- pci_release_regions(pdev);
- pci_set_drvdata(pdev, NULL);
- }
- out2:
- free_netdev(dev);
- out1:
- return err;
+err_hdlcdev:
+ pci_set_drvdata(pdev, NULL);
+ kfree(sc);
+err_kzalloc:
+ pci_release_regions(pdev);
+err_req_io:
+ pci_disable_device(pdev);
+ return err;
}
/*
* Called from pci when removing module.
*/
-static void __devexit lmc_remove_one (struct pci_dev *pdev)
+static void __devexit lmc_remove_one(struct pci_dev *pdev)
{
- struct net_device *dev = pci_get_drvdata(pdev);
-
- if (dev) {
- lmc_softc_t *sc = dev->priv;
-
- printk("%s: removing...\n", dev->name);
- lmc_proto_detach(sc);
- unregister_netdev(dev);
- free_netdev(dev);
- pci_release_regions(pdev);
- pci_disable_device(pdev);
- pci_set_drvdata(pdev, NULL);
- }
+ struct net_device *dev = pci_get_drvdata(pdev);
+
+ if (dev) {
+ printk(KERN_DEBUG "%s: removing...\n", dev->name);
+ unregister_hdlc_device(dev);
+ free_netdev(dev);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+ }
}
/* After this is called, packets can be sent.
* Does not initialize the addresses
*/
-static int lmc_open (struct net_device *dev) /*fold00*/
+static int lmc_open(struct net_device *dev)
{
- lmc_softc_t *sc = dev->priv;
+ lmc_softc_t *sc = dev_to_sc(dev);
+ int err;
lmc_trace(dev, "lmc_open in");
lmc_led_on(sc, LMC_DS3_LED0);
- lmc_dec_reset (sc);
- lmc_reset (sc);
-
- LMC_EVENT_LOG(LMC_EVENT_RESET1, LMC_CSR_READ (sc, csr_status), 0);
- LMC_EVENT_LOG(LMC_EVENT_RESET2,
- lmc_mii_readreg (sc, 0, 16),
- lmc_mii_readreg (sc, 0, 17));
+ lmc_dec_reset(sc);
+ lmc_reset(sc);
+ LMC_EVENT_LOG(LMC_EVENT_RESET1, LMC_CSR_READ(sc, csr_status), 0);
+ LMC_EVENT_LOG(LMC_EVENT_RESET2, lmc_mii_readreg(sc, 0, 16),
+ lmc_mii_readreg(sc, 0, 17));
if (sc->lmc_ok){
lmc_trace(dev, "lmc_open lmc_ok out");
/* dev->flags |= IFF_UP; */
- lmc_proto_open(sc);
+ if ((err = lmc_proto_open(sc)) != 0)
+ return err;
dev->do_ioctl = lmc_ioctl;
netif_start_queue(dev);
-
- sc->stats.tx_tbusy0++ ;
+ sc->extra_stats.tx_tbusy0++;
/*
* select what interrupts we want to get
static void lmc_running_reset (struct net_device *dev) /*fold00*/
{
-
- lmc_softc_t *sc = (lmc_softc_t *) dev->priv;
+ lmc_softc_t *sc = dev_to_sc(dev);
lmc_trace(dev, "lmc_runnig_reset in");
netif_wake_queue(dev);
sc->lmc_txfull = 0;
- sc->stats.tx_tbusy0++ ;
+ sc->extra_stats.tx_tbusy0++;
sc->lmc_intrmask = TULIP_DEFAULT_INTR_MASK;
LMC_CSR_WRITE (sc, csr_intr, sc->lmc_intrmask);
* This disables the timer for the watchdog and keepalives,
* and disables the irq for dev.
*/
-static int lmc_close (struct net_device *dev) /*fold00*/
+static int lmc_close(struct net_device *dev)
{
/* not calling release_region() as we should */
- lmc_softc_t *sc;
+ lmc_softc_t *sc = dev_to_sc(dev);
lmc_trace(dev, "lmc_close in");
-
- sc = dev->priv;
+
sc->lmc_ok = 0;
sc->lmc_media->set_link_status (sc, 0);
del_timer (&sc->timer);
lmc_ifdown (dev);
lmc_trace(dev, "lmc_close out");
-
+
return 0;
}
/* When the interface goes down, this is called */
static int lmc_ifdown (struct net_device *dev) /*fold00*/
{
- lmc_softc_t *sc = dev->priv;
+ lmc_softc_t *sc = dev_to_sc(dev);
u32 csr6;
int i;
lmc_trace(dev, "lmc_ifdown in");
-
+
/* Don't let anything else go on right now */
// dev->start = 0;
netif_stop_queue(dev);
- sc->stats.tx_tbusy1++ ;
+ sc->extra_stats.tx_tbusy1++;
/* stop interrupts */
/* Clear the interrupt mask */
csr6 &= ~LMC_DEC_SR; /* Turn off the Receive bit */
LMC_CSR_WRITE (sc, csr_command, csr6);
- sc->stats.rx_missed_errors +=
- LMC_CSR_READ (sc, csr_missed_frames) & 0xffff;
+ sc->lmc_device->stats.rx_missed_errors +=
+ LMC_CSR_READ(sc, csr_missed_frames) & 0xffff;
/* release the interrupt */
if(sc->got_irq == 1){
lmc_led_off (sc, LMC_MII16_LED_ALL);
netif_wake_queue(dev);
- sc->stats.tx_tbusy0++ ;
+ sc->extra_stats.tx_tbusy0++;
lmc_trace(dev, "lmc_ifdown out");
static irqreturn_t lmc_interrupt (int irq, void *dev_instance) /*fold00*/
{
struct net_device *dev = (struct net_device *) dev_instance;
- lmc_softc_t *sc;
+ lmc_softc_t *sc = dev_to_sc(dev);
u32 csr;
int i;
s32 stat;
lmc_trace(dev, "lmc_interrupt in");
- sc = dev->priv;
-
spin_lock(&sc->lmc_lock);
/*
int n_compl = 0 ;
/* reset the transmit timeout detection flag -baz */
- sc->stats.tx_NoCompleteCnt = 0;
+ sc->extra_stats.tx_NoCompleteCnt = 0;
badtx = sc->lmc_taint_tx;
i = badtx % LMC_TXDESCS;
if (sc->lmc_txq[i] == NULL)
continue;
- /*
- * Check the total error summary to look for any errors
- */
- if (stat & 0x8000) {
- sc->stats.tx_errors++;
- if (stat & 0x4104)
- sc->stats.tx_aborted_errors++;
- if (stat & 0x0C00)
- sc->stats.tx_carrier_errors++;
- if (stat & 0x0200)
- sc->stats.tx_window_errors++;
- if (stat & 0x0002)
- sc->stats.tx_fifo_errors++;
- }
- else {
-
- sc->stats.tx_bytes += sc->lmc_txring[i].length & 0x7ff;
-
- sc->stats.tx_packets++;
+ /*
+ * Check the total error summary to look for any errors
+ */
+ if (stat & 0x8000) {
+ sc->lmc_device->stats.tx_errors++;
+ if (stat & 0x4104)
+ sc->lmc_device->stats.tx_aborted_errors++;
+ if (stat & 0x0C00)
+ sc->lmc_device->stats.tx_carrier_errors++;
+ if (stat & 0x0200)
+ sc->lmc_device->stats.tx_window_errors++;
+ if (stat & 0x0002)
+ sc->lmc_device->stats.tx_fifo_errors++;
+ } else {
+ sc->lmc_device->stats.tx_bytes += sc->lmc_txring[i].length & 0x7ff;
+
+ sc->lmc_device->stats.tx_packets++;
}
-
+
// dev_kfree_skb(sc->lmc_txq[i]);
dev_kfree_skb_irq(sc->lmc_txq[i]);
sc->lmc_txq[i] = NULL;
LMC_EVENT_LOG(LMC_EVENT_TBUSY0, n_compl, 0);
sc->lmc_txfull = 0;
netif_wake_queue(dev);
- sc->stats.tx_tbusy0++ ;
+ sc->extra_stats.tx_tbusy0++;
#ifdef DEBUG
- sc->stats.dirtyTx = badtx;
- sc->stats.lmc_next_tx = sc->lmc_next_tx;
- sc->stats.lmc_txfull = sc->lmc_txfull;
+ sc->extra_stats.dirtyTx = badtx;
+ sc->extra_stats.lmc_next_tx = sc->lmc_next_tx;
+ sc->extra_stats.lmc_txfull = sc->lmc_txfull;
#endif
sc->lmc_taint_tx = badtx;
return IRQ_RETVAL(handled);
}
-static int lmc_start_xmit (struct sk_buff *skb, struct net_device *dev) /*fold00*/
+static int lmc_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
- lmc_softc_t *sc;
+ lmc_softc_t *sc = dev_to_sc(dev);
u32 flag;
int entry;
int ret = 0;
lmc_trace(dev, "lmc_start_xmit in");
- sc = dev->priv;
-
spin_lock_irqsave(&sc->lmc_lock, flags);
/* normal path, tbusy known to be zero */
if (sc->lmc_next_tx - sc->lmc_taint_tx >= LMC_TXDESCS - 1)
{ /* ring full, go busy */
sc->lmc_txfull = 1;
- netif_stop_queue(dev);
- sc->stats.tx_tbusy1++ ;
+ netif_stop_queue(dev);
+ sc->extra_stats.tx_tbusy1++;
LMC_EVENT_LOG(LMC_EVENT_TBUSY1, entry, 0);
}
#endif
* the watchdog timer handler. -baz
*/
- sc->stats.tx_NoCompleteCnt++;
+ sc->extra_stats.tx_NoCompleteCnt++;
sc->lmc_next_tx++;
/* give ownership to the chip */
}
-static int lmc_rx (struct net_device *dev) /*fold00*/
+static int lmc_rx(struct net_device *dev)
{
- lmc_softc_t *sc;
+ lmc_softc_t *sc = dev_to_sc(dev);
int i;
int rx_work_limit = LMC_RXDESCS;
unsigned int next_rx;
lmc_trace(dev, "lmc_rx in");
- sc = dev->priv;
-
lmc_led_on(sc, LMC_DS3_LED3);
rxIntLoopCnt = 0; /* debug -baz */
rxIntLoopCnt++; /* debug -baz */
len = ((stat & LMC_RDES_FRAME_LENGTH) >> RDES_FRAME_LENGTH_BIT_NUMBER);
if ((stat & 0x0300) != 0x0300) { /* Check first segment and last segment */
- if ((stat & 0x0000ffff) != 0x7fff) {
- /* Oversized frame */
- sc->stats.rx_length_errors++;
- goto skip_packet;
- }
- }
-
- if(stat & 0x00000008){ /* Catch a dribbling bit error */
- sc->stats.rx_errors++;
- sc->stats.rx_frame_errors++;
- goto skip_packet;
- }
+ if ((stat & 0x0000ffff) != 0x7fff) {
+ /* Oversized frame */
+ sc->lmc_device->stats.rx_length_errors++;
+ goto skip_packet;
+ }
+ }
+ if (stat & 0x00000008) { /* Catch a dribbling bit error */
+ sc->lmc_device->stats.rx_errors++;
+ sc->lmc_device->stats.rx_frame_errors++;
+ goto skip_packet;
+ }
- if(stat & 0x00000004){ /* Catch a CRC error by the Xilinx */
- sc->stats.rx_errors++;
- sc->stats.rx_crc_errors++;
- goto skip_packet;
- }
+ if (stat & 0x00000004) { /* Catch a CRC error by the Xilinx */
+ sc->lmc_device->stats.rx_errors++;
+ sc->lmc_device->stats.rx_crc_errors++;
+ goto skip_packet;
+ }
- if (len > LMC_PKT_BUF_SZ){
- sc->stats.rx_length_errors++;
- localLengthErrCnt++;
- goto skip_packet;
- }
+ if (len > LMC_PKT_BUF_SZ) {
+ sc->lmc_device->stats.rx_length_errors++;
+ localLengthErrCnt++;
+ goto skip_packet;
+ }
- if (len < sc->lmc_crcSize + 2) {
- sc->stats.rx_length_errors++;
- sc->stats.rx_SmallPktCnt++;
- localLengthErrCnt++;
- goto skip_packet;
- }
+ if (len < sc->lmc_crcSize + 2) {
+ sc->lmc_device->stats.rx_length_errors++;
+ sc->extra_stats.rx_SmallPktCnt++;
+ localLengthErrCnt++;
+ goto skip_packet;
+ }
if(stat & 0x00004000){
printk(KERN_WARNING "%s: Receiver descriptor error, receiver out of sync?\n", dev->name);
}
dev->last_rx = jiffies;
- sc->stats.rx_packets++;
- sc->stats.rx_bytes += len;
+ sc->lmc_device->stats.rx_packets++;
+ sc->lmc_device->stats.rx_bytes += len;
LMC_CONSOLE_LOG("recv", skb->data, len);
skb_put (skb, len);
skb->protocol = lmc_proto_type(sc, skb);
- skb->protocol = htons(ETH_P_WAN_PPP);
skb_reset_mac_header(skb);
/* skb_reset_network_header(skb); */
skb->dev = dev;
* in which care we'll try to allocate the buffer
* again. (once a second)
*/
- sc->stats.rx_BuffAllocErr++;
+ sc->extra_stats.rx_BuffAllocErr++;
LMC_EVENT_LOG(LMC_EVENT_RCVINT, stat, len);
sc->failed_recv_alloc = 1;
goto skip_out_of_mem;
* descriptors with bogus packets
*
if (localLengthErrCnt > LMC_RXDESCS - 3) {
- sc->stats.rx_BadPktSurgeCnt++;
- LMC_EVENT_LOG(LMC_EVENT_BADPKTSURGE,
- localLengthErrCnt,
- sc->stats.rx_BadPktSurgeCnt);
+ sc->extra_stats.rx_BadPktSurgeCnt++;
+ LMC_EVENT_LOG(LMC_EVENT_BADPKTSURGE, localLengthErrCnt,
+ sc->extra_stats.rx_BadPktSurgeCnt);
} */
/* save max count of receive descriptors serviced */
- if (rxIntLoopCnt > sc->stats.rxIntLoopCnt) {
- sc->stats.rxIntLoopCnt = rxIntLoopCnt; /* debug -baz */
- }
+ if (rxIntLoopCnt > sc->extra_stats.rxIntLoopCnt)
+ sc->extra_stats.rxIntLoopCnt = rxIntLoopCnt; /* debug -baz */
#ifdef DEBUG
if (rxIntLoopCnt == 0)
return 0;
}
-static struct net_device_stats *lmc_get_stats (struct net_device *dev) /*fold00*/
+static struct net_device_stats *lmc_get_stats(struct net_device *dev)
{
- lmc_softc_t *sc = dev->priv;
+ lmc_softc_t *sc = dev_to_sc(dev);
unsigned long flags;
lmc_trace(dev, "lmc_get_stats in");
-
spin_lock_irqsave(&sc->lmc_lock, flags);
- sc->stats.rx_missed_errors += LMC_CSR_READ (sc, csr_missed_frames) & 0xffff;
+ sc->lmc_device->stats.rx_missed_errors += LMC_CSR_READ(sc, csr_missed_frames) & 0xffff;
spin_unlock_irqrestore(&sc->lmc_lock, flags);
lmc_trace(dev, "lmc_get_stats out");
- return (struct net_device_stats *) &sc->stats;
+ return &sc->lmc_device->stats;
}
static struct pci_driver lmc_driver = {
{
if (sc->lmc_txq[i] != NULL){ /* have buffer */
dev_kfree_skb(sc->lmc_txq[i]); /* free it */
- sc->stats.tx_dropped++; /* We just dropped a packet */
+ sc->lmc_device->stats.tx_dropped++; /* We just dropped a packet */
}
sc->lmc_txq[i] = NULL;
sc->lmc_txring[i].status = 0x00000000;
lmc_trace(sc->lmc_device, "lmc_softreset out");
}
-void lmc_gpio_mkinput(lmc_softc_t * const sc, u_int32_t bits) /*fold00*/
+void lmc_gpio_mkinput(lmc_softc_t * const sc, u32 bits) /*fold00*/
{
lmc_trace(sc->lmc_device, "lmc_gpio_mkinput in");
sc->lmc_gpio_io &= ~bits;
lmc_trace(sc->lmc_device, "lmc_gpio_mkinput out");
}
-void lmc_gpio_mkoutput(lmc_softc_t * const sc, u_int32_t bits) /*fold00*/
+void lmc_gpio_mkoutput(lmc_softc_t * const sc, u32 bits) /*fold00*/
{
lmc_trace(sc->lmc_device, "lmc_gpio_mkoutput in");
sc->lmc_gpio_io |= bits;
lmc_trace(sc->lmc_device, "lmc_gpio_mkoutput out");
}
-void lmc_led_on(lmc_softc_t * const sc, u_int32_t led) /*fold00*/
+void lmc_led_on(lmc_softc_t * const sc, u32 led) /*fold00*/
{
lmc_trace(sc->lmc_device, "lmc_led_on in");
if((~sc->lmc_miireg16) & led){ /* Already on! */
lmc_trace(sc->lmc_device, "lmc_led_on out");
}
-void lmc_led_off(lmc_softc_t * const sc, u_int32_t led) /*fold00*/
+void lmc_led_off(lmc_softc_t * const sc, u32 led) /*fold00*/
{
lmc_trace(sc->lmc_device, "lmc_led_off in");
if(sc->lmc_miireg16 & led){ /* Already set don't do anything */
*/
sc->lmc_media->init(sc);
- sc->stats.resetCount++;
+ sc->extra_stats.resetCount++;
lmc_trace(sc->lmc_device, "lmc_reset out");
}
static void lmc_dec_reset(lmc_softc_t * const sc) /*fold00*/
{
- u_int32_t val;
+ u32 val;
lmc_trace(sc->lmc_device, "lmc_dec_reset in");
/*
lmc_trace(sc->lmc_device, "lmc_initcsrs out");
}
-static void lmc_driver_timeout(struct net_device *dev) { /*fold00*/
- lmc_softc_t *sc;
+static void lmc_driver_timeout(struct net_device *dev)
+{
+ lmc_softc_t *sc = dev_to_sc(dev);
u32 csr6;
unsigned long flags;
lmc_trace(dev, "lmc_driver_timeout in");
- sc = dev->priv;
-
spin_lock_irqsave(&sc->lmc_lock, flags);
printk("%s: Xmitter busy|\n", dev->name);
- sc->stats.tx_tbusy_calls++ ;
- if (jiffies - dev->trans_start < TX_TIMEOUT) {
- goto bug_out;
- }
+ sc->extra_stats.tx_tbusy_calls++;
+ if (jiffies - dev->trans_start < TX_TIMEOUT)
+ goto bug_out;
/*
* Chip seems to have locked up
LMC_EVENT_LOG(LMC_EVENT_XMTPRCTMO,
LMC_CSR_READ (sc, csr_status),
- sc->stats.tx_ProcTimeout);
+ sc->extra_stats.tx_ProcTimeout);
lmc_running_reset (dev);
/* immediate transmit */
LMC_CSR_WRITE (sc, csr_txpoll, 0);
- sc->stats.tx_errors++;
- sc->stats.tx_ProcTimeout++; /* -baz */
+ sc->lmc_device->stats.tx_errors++;
+ sc->extra_stats.tx_ProcTimeout++; /* -baz */
dev->trans_start = jiffies;
#include <linux/inet.h>
#include <linux/bitops.h>
-#include <net/syncppp.h>
-
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/io.h>
#include <asm/dma.h>
static void lmc_dummy_set2_1 (lmc_softc_t * const, lmc_ctl_t *);
static inline void write_av9110_bit (lmc_softc_t *, int);
-static void write_av9110 (lmc_softc_t *, u_int32_t, u_int32_t, u_int32_t,
- u_int32_t, u_int32_t);
+static void write_av9110(lmc_softc_t *, u32, u32, u32, u32, u32);
lmc_media_t lmc_ds3_media = {
lmc_ds3_init, /* special media init stuff */
static int
lmc_ds3_get_link_status (lmc_softc_t * const sc)
{
- u_int16_t link_status, link_status_11;
+ u16 link_status, link_status_11;
int ret = 1;
lmc_mii_writereg (sc, 0, 17, 7);
(link_status & LMC_FRAMER_REG0_OOFS)){
ret = 0;
if(sc->last_led_err[3] != 1){
- u16 r1;
+ u16 r1;
lmc_mii_writereg (sc, 0, 17, 01); /* Turn on Xbit error as our cisco does */
r1 = lmc_mii_readreg (sc, 0, 18);
r1 &= 0xfe;
else {
lmc_led_off(sc, LMC_DS3_LED3); /* turn on red LED */
if(sc->last_led_err[3] == 1){
- u16 r1;
+ u16 r1;
lmc_mii_writereg (sc, 0, 17, 01); /* Turn off Xbit error */
r1 = lmc_mii_readreg (sc, 0, 18);
r1 |= 0x01;
* SSI methods
*/
-static void
-lmc_ssi_init (lmc_softc_t * const sc)
+static void lmc_ssi_init(lmc_softc_t * const sc)
{
- u_int16_t mii17;
- int cable;
+ u16 mii17;
+ int cable;
- sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC1000;
+ sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC1000;
- mii17 = lmc_mii_readreg (sc, 0, 17);
+ mii17 = lmc_mii_readreg(sc, 0, 17);
- cable = (mii17 & LMC_MII17_SSI_CABLE_MASK) >> LMC_MII17_SSI_CABLE_SHIFT;
- sc->ictl.cable_type = cable;
+ cable = (mii17 & LMC_MII17_SSI_CABLE_MASK) >> LMC_MII17_SSI_CABLE_SHIFT;
+ sc->ictl.cable_type = cable;
- lmc_gpio_mkoutput (sc, LMC_GEP_SSI_TXCLOCK);
+ lmc_gpio_mkoutput(sc, LMC_GEP_SSI_TXCLOCK);
}
static void
static int
lmc_ssi_get_link_status (lmc_softc_t * const sc)
{
- u_int16_t link_status;
- u_int32_t ticks;
+ u16 link_status;
+ u32 ticks;
int ret = 1;
int hw_hdsk = 1;
-
+
/*
* missing CTS? Hmm. If we require CTS on, we may never get the
* link to come up, so omit it in this test.
}
else if (ticks == 0 ) { /* no clock found ? */
ret = 0;
- if(sc->last_led_err[3] != 1){
- sc->stats.tx_lossOfClockCnt++;
- printk(KERN_WARNING "%s: Lost Clock, Link Down\n", sc->name);
+ if (sc->last_led_err[3] != 1) {
+ sc->extra_stats.tx_lossOfClockCnt++;
+ printk(KERN_WARNING "%s: Lost Clock, Link Down\n", sc->name);
}
sc->last_led_err[3] = 1;
lmc_led_on (sc, LMC_MII16_LED3); /* turn ON red LED */
LMC_CSR_WRITE (sc, csr_gp, sc->lmc_gpio);
}
-static void
-write_av9110 (lmc_softc_t * sc, u_int32_t n, u_int32_t m, u_int32_t v,
- u_int32_t x, u_int32_t r)
+static void write_av9110(lmc_softc_t *sc, u32 n, u32 m, u32 v, u32 x, u32 r)
{
int i;
| LMC_GEP_SSI_GENERATOR));
}
-static void
-lmc_ssi_watchdog (lmc_softc_t * const sc)
+static void lmc_ssi_watchdog(lmc_softc_t * const sc)
{
- u_int16_t mii17 = lmc_mii_readreg (sc, 0, 17);
- if (((mii17 >> 3) & 7) == 7)
- {
- lmc_led_off (sc, LMC_MII16_LED2);
- }
- else
- {
- lmc_led_on (sc, LMC_MII16_LED2);
- }
-
+ u16 mii17 = lmc_mii_readreg(sc, 0, 17);
+ if (((mii17 >> 3) & 7) == 7)
+ lmc_led_off(sc, LMC_MII16_LED2);
+ else
+ lmc_led_on(sc, LMC_MII16_LED2);
}
/*
static void
lmc_t1_init (lmc_softc_t * const sc)
{
- u_int16_t mii16;
+ u16 mii16;
int i;
sc->ictl.cardtype = LMC_CTL_CARDTYPE_LMC1200;
*/ static int
lmc_t1_get_link_status (lmc_softc_t * const sc)
{
- u_int16_t link_status;
+ u16 link_status;
int ret = 1;
/* LMC5245 (DS3) & LMC1200 (DS1) LED definitions
#include <linux/workqueue.h>
#include <linux/proc_fs.h>
#include <linux/bitops.h>
-
-#include <net/syncppp.h>
-
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/io.h>
#include <asm/dma.h>
#include "lmc_ioctl.h"
#include "lmc_proto.h"
-/*
- * The compile-time variable SPPPSTUP causes the module to be
- * compiled without referencing any of the sync ppp routines.
- */
-#ifdef SPPPSTUB
-#define SPPP_detach(d) (void)0
-#define SPPP_open(d) 0
-#define SPPP_reopen(d) (void)0
-#define SPPP_close(d) (void)0
-#define SPPP_attach(d) (void)0
-#define SPPP_do_ioctl(d,i,c) -EOPNOTSUPP
-#else
-#define SPPP_attach(x) sppp_attach((x)->pd)
-#define SPPP_detach(x) sppp_detach((x)->pd->dev)
-#define SPPP_open(x) sppp_open((x)->pd->dev)
-#define SPPP_reopen(x) sppp_reopen((x)->pd->dev)
-#define SPPP_close(x) sppp_close((x)->pd->dev)
-#define SPPP_do_ioctl(x, y, z) sppp_do_ioctl((x)->pd->dev, (y), (z))
-#endif
-
-// init
-void lmc_proto_init(lmc_softc_t *sc) /*FOLD00*/
-{
- lmc_trace(sc->lmc_device, "lmc_proto_init in");
- switch(sc->if_type){
- case LMC_PPP:
- sc->pd = kmalloc(sizeof(struct ppp_device), GFP_KERNEL);
- if (!sc->pd) {
- printk("lmc_proto_init(): kmalloc failure!\n");
- return;
- }
- sc->pd->dev = sc->lmc_device;
- sc->if_ptr = sc->pd;
- break;
- case LMC_RAW:
- break;
- default:
- break;
- }
- lmc_trace(sc->lmc_device, "lmc_proto_init out");
-}
-
// attach
void lmc_proto_attach(lmc_softc_t *sc) /*FOLD00*/
{
case LMC_PPP:
{
struct net_device *dev = sc->lmc_device;
- SPPP_attach(sc);
dev->do_ioctl = lmc_ioctl;
}
break;
{
struct net_device *dev = sc->lmc_device;
/*
- * They set a few basics because they don't use sync_ppp
+ * They set a few basics because they don't use HDLC
*/
dev->flags |= IFF_POINTOPOINT;
lmc_trace(sc->lmc_device, "lmc_proto_attach out");
}
-// detach
-void lmc_proto_detach(lmc_softc_t *sc) /*FOLD00*/
+int lmc_proto_ioctl(lmc_softc_t *sc, struct ifreq *ifr, int cmd)
{
- switch(sc->if_type){
- case LMC_PPP:
- SPPP_detach(sc);
- break;
- case LMC_RAW: /* Tell someone we're detaching? */
- break;
- default:
- break;
- }
-
+ lmc_trace(sc->lmc_device, "lmc_proto_ioctl");
+ if (sc->if_type == LMC_PPP)
+ return hdlc_ioctl(sc->lmc_device, ifr, cmd);
+ return -EOPNOTSUPP;
}
-// reopen
-void lmc_proto_reopen(lmc_softc_t *sc) /*FOLD00*/
+int lmc_proto_open(lmc_softc_t *sc)
{
- lmc_trace(sc->lmc_device, "lmc_proto_reopen in");
- switch(sc->if_type){
- case LMC_PPP:
- SPPP_reopen(sc);
- break;
- case LMC_RAW: /* Reset the interface after being down, prerape to receive packets again */
- break;
- default:
- break;
- }
- lmc_trace(sc->lmc_device, "lmc_proto_reopen out");
-}
+ int ret = 0;
+ lmc_trace(sc->lmc_device, "lmc_proto_open in");
-// ioctl
-int lmc_proto_ioctl(lmc_softc_t *sc, struct ifreq *ifr, int cmd) /*FOLD00*/
-{
- lmc_trace(sc->lmc_device, "lmc_proto_ioctl out");
- switch(sc->if_type){
- case LMC_PPP:
- return SPPP_do_ioctl (sc, ifr, cmd);
- break;
- default:
- return -EOPNOTSUPP;
- break;
- }
- lmc_trace(sc->lmc_device, "lmc_proto_ioctl out");
+ if (sc->if_type == LMC_PPP) {
+ ret = hdlc_open(sc->lmc_device);
+ if (ret < 0)
+ printk(KERN_WARNING "%s: HDLC open failed: %d\n",
+ sc->name, ret);
+ }
+
+ lmc_trace(sc->lmc_device, "lmc_proto_open out");
+ return ret;
}
-// open
-void lmc_proto_open(lmc_softc_t *sc) /*FOLD00*/
+void lmc_proto_close(lmc_softc_t *sc)
{
- int ret;
+ lmc_trace(sc->lmc_device, "lmc_proto_close in");
- lmc_trace(sc->lmc_device, "lmc_proto_open in");
- switch(sc->if_type){
- case LMC_PPP:
- ret = SPPP_open(sc);
- if(ret < 0)
- printk("%s: syncPPP open failed: %d\n", sc->name, ret);
- break;
- case LMC_RAW: /* We're about to start getting packets! */
- break;
- default:
- break;
- }
- lmc_trace(sc->lmc_device, "lmc_proto_open out");
-}
-
-// close
+ if (sc->if_type == LMC_PPP)
+ hdlc_close(sc->lmc_device);
-void lmc_proto_close(lmc_softc_t *sc) /*FOLD00*/
-{
- lmc_trace(sc->lmc_device, "lmc_proto_close in");
- switch(sc->if_type){
- case LMC_PPP:
- SPPP_close(sc);
- break;
- case LMC_RAW: /* Interface going down */
- break;
- default:
- break;
- }
- lmc_trace(sc->lmc_device, "lmc_proto_close out");
+ lmc_trace(sc->lmc_device, "lmc_proto_close out");
}
__be16 lmc_proto_type(lmc_softc_t *sc, struct sk_buff *skb) /*FOLD00*/
lmc_trace(sc->lmc_device, "lmc_proto_type in");
switch(sc->if_type){
case LMC_PPP:
- return htons(ETH_P_WAN_PPP);
- break;
+ return hdlc_type_trans(skb, sc->lmc_device);
+ break;
case LMC_NET:
return htons(ETH_P_802_2);
break;
}
lmc_trace(sc->lmc_device, "lmc_proto_netif out");
}
-
#ifndef _LMC_PROTO_H_
#define _LMC_PROTO_H_
-void lmc_proto_init(lmc_softc_t *sc);
+#include <linux/hdlc.h>
+
void lmc_proto_attach(lmc_softc_t *sc);
-void lmc_proto_detach(lmc_softc_t *sc);
-void lmc_proto_reopen(lmc_softc_t *sc);
int lmc_proto_ioctl(lmc_softc_t *sc, struct ifreq *ifr, int cmd);
-void lmc_proto_open(lmc_softc_t *sc);
+int lmc_proto_open(lmc_softc_t *sc);
void lmc_proto_close(lmc_softc_t *sc);
__be16 lmc_proto_type(lmc_softc_t *sc, struct sk_buff *skb);
void lmc_proto_netif(lmc_softc_t *sc, struct sk_buff *skb);
-int lmc_skb_rawpackets(char *buf, char **start, off_t offset, int len, int unused);
-#endif
+static inline lmc_softc_t* dev_to_sc(struct net_device *dev)
+{
+ return (lmc_softc_t *)dev_to_hdlc(dev)->priv;
+}
+#endif
#ifndef _LMC_VAR_H_
#define _LMC_VAR_H_
-/* $Id: lmc_var.h,v 1.17 2000/04/06 12:16:47 asj Exp $ */
-
/*
* Copyright (c) 1997-2000 LAN Media Corporation (LMC)
* All rights reserved. www.lanmedia.com
#include <linux/timer.h>
-#ifndef __KERNEL__
-typedef signed char s8;
-typedef unsigned char u8;
-
-typedef signed short s16;
-typedef unsigned short u16;
-
-typedef signed int s32;
-typedef unsigned int u32;
-
-typedef signed long long s64;
-typedef unsigned long long u64;
-
-#define BITS_PER_LONG 32
-
-#endif
-
/*
* basic definitions used in lmc include files
*/
typedef struct lmc___ctl lmc_ctl_t;
#define lmc_csrptr_t unsigned long
-#define u_int16_t u16
-#define u_int8_t u8
-#define tulip_uint32_t u32
#define LMC_REG_RANGE 0x80
* used to define bits in the second tulip_desc_t field (length)
* for the transmit descriptor -baz */
-#define LMC_TDES_FIRST_BUFFER_SIZE ((u_int32_t)(0x000007FF))
-#define LMC_TDES_SECOND_BUFFER_SIZE ((u_int32_t)(0x003FF800))
-#define LMC_TDES_HASH_FILTERING ((u_int32_t)(0x00400000))
-#define LMC_TDES_DISABLE_PADDING ((u_int32_t)(0x00800000))
-#define LMC_TDES_SECOND_ADDR_CHAINED ((u_int32_t)(0x01000000))
-#define LMC_TDES_END_OF_RING ((u_int32_t)(0x02000000))
-#define LMC_TDES_ADD_CRC_DISABLE ((u_int32_t)(0x04000000))
-#define LMC_TDES_SETUP_PACKET ((u_int32_t)(0x08000000))
-#define LMC_TDES_INVERSE_FILTERING ((u_int32_t)(0x10000000))
-#define LMC_TDES_FIRST_SEGMENT ((u_int32_t)(0x20000000))
-#define LMC_TDES_LAST_SEGMENT ((u_int32_t)(0x40000000))
-#define LMC_TDES_INTERRUPT_ON_COMPLETION ((u_int32_t)(0x80000000))
+#define LMC_TDES_FIRST_BUFFER_SIZE ((u32)(0x000007FF))
+#define LMC_TDES_SECOND_BUFFER_SIZE ((u32)(0x003FF800))
+#define LMC_TDES_HASH_FILTERING ((u32)(0x00400000))
+#define LMC_TDES_DISABLE_PADDING ((u32)(0x00800000))
+#define LMC_TDES_SECOND_ADDR_CHAINED ((u32)(0x01000000))
+#define LMC_TDES_END_OF_RING ((u32)(0x02000000))
+#define LMC_TDES_ADD_CRC_DISABLE ((u32)(0x04000000))
+#define LMC_TDES_SETUP_PACKET ((u32)(0x08000000))
+#define LMC_TDES_INVERSE_FILTERING ((u32)(0x10000000))
+#define LMC_TDES_FIRST_SEGMENT ((u32)(0x20000000))
+#define LMC_TDES_LAST_SEGMENT ((u32)(0x40000000))
+#define LMC_TDES_INTERRUPT_ON_COMPLETION ((u32)(0x80000000))
#define TDES_SECOND_BUFFER_SIZE_BIT_NUMBER 11
#define TDES_COLLISION_COUNT_BIT_NUMBER 3
/* Constants for the RCV descriptor RDES */
-#define LMC_RDES_OVERFLOW ((u_int32_t)(0x00000001))
-#define LMC_RDES_CRC_ERROR ((u_int32_t)(0x00000002))
-#define LMC_RDES_DRIBBLING_BIT ((u_int32_t)(0x00000004))
-#define LMC_RDES_REPORT_ON_MII_ERR ((u_int32_t)(0x00000008))
-#define LMC_RDES_RCV_WATCHDOG_TIMEOUT ((u_int32_t)(0x00000010))
-#define LMC_RDES_FRAME_TYPE ((u_int32_t)(0x00000020))
-#define LMC_RDES_COLLISION_SEEN ((u_int32_t)(0x00000040))
-#define LMC_RDES_FRAME_TOO_LONG ((u_int32_t)(0x00000080))
-#define LMC_RDES_LAST_DESCRIPTOR ((u_int32_t)(0x00000100))
-#define LMC_RDES_FIRST_DESCRIPTOR ((u_int32_t)(0x00000200))
-#define LMC_RDES_MULTICAST_FRAME ((u_int32_t)(0x00000400))
-#define LMC_RDES_RUNT_FRAME ((u_int32_t)(0x00000800))
-#define LMC_RDES_DATA_TYPE ((u_int32_t)(0x00003000))
-#define LMC_RDES_LENGTH_ERROR ((u_int32_t)(0x00004000))
-#define LMC_RDES_ERROR_SUMMARY ((u_int32_t)(0x00008000))
-#define LMC_RDES_FRAME_LENGTH ((u_int32_t)(0x3FFF0000))
-#define LMC_RDES_OWN_BIT ((u_int32_t)(0x80000000))
+#define LMC_RDES_OVERFLOW ((u32)(0x00000001))
+#define LMC_RDES_CRC_ERROR ((u32)(0x00000002))
+#define LMC_RDES_DRIBBLING_BIT ((u32)(0x00000004))
+#define LMC_RDES_REPORT_ON_MII_ERR ((u32)(0x00000008))
+#define LMC_RDES_RCV_WATCHDOG_TIMEOUT ((u32)(0x00000010))
+#define LMC_RDES_FRAME_TYPE ((u32)(0x00000020))
+#define LMC_RDES_COLLISION_SEEN ((u32)(0x00000040))
+#define LMC_RDES_FRAME_TOO_LONG ((u32)(0x00000080))
+#define LMC_RDES_LAST_DESCRIPTOR ((u32)(0x00000100))
+#define LMC_RDES_FIRST_DESCRIPTOR ((u32)(0x00000200))
+#define LMC_RDES_MULTICAST_FRAME ((u32)(0x00000400))
+#define LMC_RDES_RUNT_FRAME ((u32)(0x00000800))
+#define LMC_RDES_DATA_TYPE ((u32)(0x00003000))
+#define LMC_RDES_LENGTH_ERROR ((u32)(0x00004000))
+#define LMC_RDES_ERROR_SUMMARY ((u32)(0x00008000))
+#define LMC_RDES_FRAME_LENGTH ((u32)(0x3FFF0000))
+#define LMC_RDES_OWN_BIT ((u32)(0x80000000))
#define RDES_FRAME_LENGTH_BIT_NUMBER 16
-#define LMC_RDES_ERROR_MASK ( (u_int32_t)( \
+#define LMC_RDES_ERROR_MASK ( (u32)( \
LMC_RDES_OVERFLOW \
| LMC_RDES_DRIBBLING_BIT \
| LMC_RDES_REPORT_ON_MII_ERR \
*/
typedef struct {
- u_int32_t n;
- u_int32_t m;
- u_int32_t v;
- u_int32_t x;
- u_int32_t r;
- u_int32_t f;
- u_int32_t exact;
+ u32 n;
+ u32 m;
+ u32 v;
+ u32 x;
+ u32 r;
+ u32 f;
+ u32 exact;
} lmc_av9110_t;
/*
* Common structure passed to the ioctl code.
*/
struct lmc___ctl {
- u_int32_t cardtype;
- u_int32_t clock_source; /* HSSI, T1 */
- u_int32_t clock_rate; /* T1 */
- u_int32_t crc_length;
- u_int32_t cable_length; /* DS3 */
- u_int32_t scrambler_onoff; /* DS3 */
- u_int32_t cable_type; /* T1 */
- u_int32_t keepalive_onoff; /* protocol */
- u_int32_t ticks; /* ticks/sec */
+ u32 cardtype;
+ u32 clock_source; /* HSSI, T1 */
+ u32 clock_rate; /* T1 */
+ u32 crc_length;
+ u32 cable_length; /* DS3 */
+ u32 scrambler_onoff; /* DS3 */
+ u32 cable_type; /* T1 */
+ u32 keepalive_onoff; /* protocol */
+ u32 ticks; /* ticks/sec */
union {
lmc_av9110_t ssi;
} cardspec;
- u_int32_t circuit_type; /* T1 or E1 */
+ u32 circuit_type; /* T1 or E1 */
};
#define STATCHECK 0xBEEFCAFE
-/* Included in this structure are first
- * - standard net_device_stats
- * - some other counters used for debug and driver performance
- * evaluation -baz
- */
-struct lmc_statistics
+struct lmc_extra_statistics
{
- unsigned long rx_packets; /* total packets received */
- unsigned long tx_packets; /* total packets transmitted */
- unsigned long rx_bytes;
- unsigned long tx_bytes;
-
- unsigned long rx_errors; /* bad packets received */
- unsigned long tx_errors; /* packet transmit problems */
- unsigned long rx_dropped; /* no space in linux buffers */
- unsigned long tx_dropped; /* no space available in linux */
- unsigned long multicast; /* multicast packets received */
- unsigned long collisions;
-
- /* detailed rx_errors: */
- unsigned long rx_length_errors;
- unsigned long rx_over_errors; /* receiver ring buff overflow */
- unsigned long rx_crc_errors; /* recved pkt with crc error */
- unsigned long rx_frame_errors; /* recv'd frame alignment error */
- unsigned long rx_fifo_errors; /* recv'r fifo overrun */
- unsigned long rx_missed_errors; /* receiver missed packet */
-
- /* detailed tx_errors */
- unsigned long tx_aborted_errors;
- unsigned long tx_carrier_errors;
- unsigned long tx_fifo_errors;
- unsigned long tx_heartbeat_errors;
- unsigned long tx_window_errors;
-
- /* for cslip etc */
- unsigned long rx_compressed;
- unsigned long tx_compressed;
-
- /* -------------------------------------
- * Custom stats & counters follow -baz */
- u_int32_t version_size;
- u_int32_t lmc_cardtype;
-
- u_int32_t tx_ProcTimeout;
- u_int32_t tx_IntTimeout;
- u_int32_t tx_NoCompleteCnt;
- u_int32_t tx_MaxXmtsB4Int;
- u_int32_t tx_TimeoutCnt;
- u_int32_t tx_OutOfSyncPtr;
- u_int32_t tx_tbusy0;
- u_int32_t tx_tbusy1;
- u_int32_t tx_tbusy_calls;
- u_int32_t resetCount;
- u_int32_t lmc_txfull;
- u_int32_t tbusy;
- u_int32_t dirtyTx;
- u_int32_t lmc_next_tx;
- u_int32_t otherTypeCnt;
- u_int32_t lastType;
- u_int32_t lastTypeOK;
- u_int32_t txLoopCnt;
- u_int32_t usedXmtDescripCnt;
- u_int32_t txIndexCnt;
- u_int32_t rxIntLoopCnt;
-
- u_int32_t rx_SmallPktCnt;
- u_int32_t rx_BadPktSurgeCnt;
- u_int32_t rx_BuffAllocErr;
- u_int32_t tx_lossOfClockCnt;
-
- /* T1 error counters */
- u_int32_t framingBitErrorCount;
- u_int32_t lineCodeViolationCount;
-
- u_int32_t lossOfFrameCount;
- u_int32_t changeOfFrameAlignmentCount;
- u_int32_t severelyErroredFrameCount;
-
- u_int32_t check;
+ u32 version_size;
+ u32 lmc_cardtype;
+
+ u32 tx_ProcTimeout;
+ u32 tx_IntTimeout;
+ u32 tx_NoCompleteCnt;
+ u32 tx_MaxXmtsB4Int;
+ u32 tx_TimeoutCnt;
+ u32 tx_OutOfSyncPtr;
+ u32 tx_tbusy0;
+ u32 tx_tbusy1;
+ u32 tx_tbusy_calls;
+ u32 resetCount;
+ u32 lmc_txfull;
+ u32 tbusy;
+ u32 dirtyTx;
+ u32 lmc_next_tx;
+ u32 otherTypeCnt;
+ u32 lastType;
+ u32 lastTypeOK;
+ u32 txLoopCnt;
+ u32 usedXmtDescripCnt;
+ u32 txIndexCnt;
+ u32 rxIntLoopCnt;
+
+ u32 rx_SmallPktCnt;
+ u32 rx_BadPktSurgeCnt;
+ u32 rx_BuffAllocErr;
+ u32 tx_lossOfClockCnt;
+
+ /* T1 error counters */
+ u32 framingBitErrorCount;
+ u32 lineCodeViolationCount;
+
+ u32 lossOfFrameCount;
+ u32 changeOfFrameAlignmentCount;
+ u32 severelyErroredFrameCount;
+
+ u32 check;
};
-
typedef struct lmc_xinfo {
- u_int32_t Magic0; /* BEEFCAFE */
+ u32 Magic0; /* BEEFCAFE */
- u_int32_t PciCardType;
- u_int32_t PciSlotNumber; /* PCI slot number */
+ u32 PciCardType;
+ u32 PciSlotNumber; /* PCI slot number */
- u_int16_t DriverMajorVersion;
- u_int16_t DriverMinorVersion;
- u_int16_t DriverSubVersion;
+ u16 DriverMajorVersion;
+ u16 DriverMinorVersion;
+ u16 DriverSubVersion;
- u_int16_t XilinxRevisionNumber;
- u_int16_t MaxFrameSize;
+ u16 XilinxRevisionNumber;
+ u16 MaxFrameSize;
- u_int16_t t1_alarm1_status;
- u_int16_t t1_alarm2_status;
+ u16 t1_alarm1_status;
+ u16 t1_alarm2_status;
- int link_status;
- u_int32_t mii_reg16;
+ int link_status;
+ u32 mii_reg16;
- u_int32_t Magic1; /* DEADBEEF */
+ u32 Magic1; /* DEADBEEF */
} LMC_XINFO;
* forward decl
*/
struct lmc___softc {
- void *if_ptr; /* General purpose pointer (used by SPPP) */
char *name;
u8 board_idx;
- struct lmc_statistics stats;
- struct net_device *lmc_device;
+ struct lmc_extra_statistics extra_stats;
+ struct net_device *lmc_device;
int hang, rxdesc, bad_packet, some_counter;
- u_int32_t txgo;
+ u32 txgo;
struct lmc_regfile_t lmc_csrs;
- volatile u_int32_t lmc_txtick;
- volatile u_int32_t lmc_rxtick;
- u_int32_t lmc_flags;
- u_int32_t lmc_intrmask; /* our copy of csr_intr */
- u_int32_t lmc_cmdmode; /* our copy of csr_cmdmode */
- u_int32_t lmc_busmode; /* our copy of csr_busmode */
- u_int32_t lmc_gpio_io; /* state of in/out settings */
- u_int32_t lmc_gpio; /* state of outputs */
+ volatile u32 lmc_txtick;
+ volatile u32 lmc_rxtick;
+ u32 lmc_flags;
+ u32 lmc_intrmask; /* our copy of csr_intr */
+ u32 lmc_cmdmode; /* our copy of csr_cmdmode */
+ u32 lmc_busmode; /* our copy of csr_busmode */
+ u32 lmc_gpio_io; /* state of in/out settings */
+ u32 lmc_gpio; /* state of outputs */
struct sk_buff* lmc_txq[LMC_TXDESCS];
struct sk_buff* lmc_rxq[LMC_RXDESCS];
volatile
unsigned int lmc_taint_tx, lmc_taint_rx;
int lmc_tx_start, lmc_txfull;
int lmc_txbusy;
- u_int16_t lmc_miireg16;
+ u16 lmc_miireg16;
int lmc_ok;
int last_link_status;
int lmc_cardtype;
- u_int32_t last_frameerr;
+ u32 last_frameerr;
lmc_media_t *lmc_media;
struct timer_list timer;
lmc_ctl_t ictl;
- u_int32_t TxDescriptControlInit;
+ u32 TxDescriptControlInit;
int tx_TimeoutInd; /* additional driver state */
int tx_TimeoutDisplay;
unsigned int lastlmc_taint_tx;
int lasttx_packets;
- u_int32_t tx_clockState;
- u_int32_t lmc_crcSize;
- LMC_XINFO lmc_xinfo;
+ u32 tx_clockState;
+ u32 lmc_crcSize;
+ LMC_XINFO lmc_xinfo;
char lmc_yel, lmc_blue, lmc_red; /* for T1 and DS3 */
- char lmc_timing; /* for HSSI and SSI */
- int got_irq;
+ char lmc_timing; /* for HSSI and SSI */
+ int got_irq;
- char last_led_err[4];
+ char last_led_err[4];
- u32 last_int;
- u32 num_int;
+ u32 last_int;
+ u32 num_int;
spinlock_t lmc_lock;
- u_int16_t if_type; /* PPP or NET */
- struct ppp_device *pd;
+ u16 if_type; /* HDLC/PPP or NET */
- /* Failure cases */
- u8 failed_ring;
- u8 failed_recv_alloc;
+ /* Failure cases */
+ u8 failed_ring;
+ u8 failed_recv_alloc;
- /* Structure check */
- u32 check;
+ /* Structure check */
+ u32 check;
};
#define LMC_PCI_TIME 1
| TULIP_STS_TXUNDERFLOW\
| TULIP_STS_RXSTOPPED )
-#define DESC_OWNED_BY_SYSTEM ((u_int32_t)(0x00000000))
-#define DESC_OWNED_BY_DC21X4 ((u_int32_t)(0x80000000))
+#define DESC_OWNED_BY_SYSTEM ((u32)(0x00000000))
+#define DESC_OWNED_BY_DC21X4 ((u32)(0x80000000))
#ifndef TULIP_CMD_RECEIVEALL
#define TULIP_CMD_RECEIVEALL 0x40000000L
#define LMC_ADAP_SSI 4
#define LMC_ADAP_T1 5
-#define HDLC_HDR_LEN 4
-#define HDLC_ADDR_LEN 1
-#define HDLC_SLARP 0x8035
#define LMC_MTU 1500
-#define SLARP_LINECHECK 2
#define LMC_CRC_LEN_16 2 /* 16-bit CRC */
#define LMC_CRC_LEN_32 4
-#ifdef LMC_HDLC
-/* definition of an hdlc header. */
-struct hdlc_hdr
-{
- u8 address;
- u8 control;
- u16 type;
-};
-
-/* definition of a slarp header. */
-struct slarp
-{
- long code;
- union sl
- {
- struct
- {
- ulong address;
- ulong mask;
- ushort unused;
- } add;
- struct
- {
- ulong mysequence;
- ulong yoursequence;
- ushort reliability;
- ulong time;
- } chk;
- } t;
-};
-#endif /* LMC_HDLC */
-
-
#endif /* _LMC_VAR_H_ */
#define _PC300_H
#include <linux/hdlc.h>
-#include <net/syncppp.h>
#include "hd64572.h"
#include "pc300-falc-lh.h"
-#ifndef CY_TYPES
-#define CY_TYPES
-typedef __u64 ucdouble; /* 64 bits, unsigned */
-typedef __u32 uclong; /* 32 bits, unsigned */
-typedef __u16 ucshort; /* 16 bits, unsigned */
-typedef __u8 ucchar; /* 8 bits, unsigned */
-#endif /* CY_TYPES */
+#define PC300_PROTO_MLPPP 1
-#define PC300_PROTO_MLPPP 1
-
-#define PC300_KERNEL "2.4.x" /* Kernel supported by this driver */
-
-#define PC300_DEVNAME "hdlc" /* Dev. name base (for hdlc0, hdlc1, etc.) */
-#define PC300_MAXINDEX 100 /* Max dev. name index (the '0' in hdlc0) */
-
-#define PC300_MAXCARDS 4 /* Max number of cards per system */
#define PC300_MAXCHAN 2 /* Number of channels per card */
-#define PC300_PLX_WIN 0x80 /* PLX control window size (128b) */
#define PC300_RAMSIZE 0x40000 /* RAM window size (256Kb) */
-#define PC300_SCASIZE 0x400 /* SCA window size (1Kb) */
#define PC300_FALCSIZE 0x400 /* FALC window size (1Kb) */
#define PC300_OSC_CLOCK 24576000
* Memory access functions/macros *
* (required to support Alpha systems) *
***************************************/
-#ifdef __KERNEL__
-#define cpc_writeb(port,val) {writeb((ucchar)(val),(port)); mb();}
+#define cpc_writeb(port,val) {writeb((u8)(val),(port)); mb();}
#define cpc_writew(port,val) {writew((ushort)(val),(port)); mb();}
-#define cpc_writel(port,val) {writel((uclong)(val),(port)); mb();}
+#define cpc_writel(port,val) {writel((u32)(val),(port)); mb();}
#define cpc_readb(port) readb(port)
#define cpc_readw(port) readw(port)
#define cpc_readl(port) readl(port)
-#else /* __KERNEL__ */
-#define cpc_writeb(port,val) (*(volatile ucchar *)(port) = (ucchar)(val))
-#define cpc_writew(port,val) (*(volatile ucshort *)(port) = (ucshort)(val))
-#define cpc_writel(port,val) (*(volatile uclong *)(port) = (uclong)(val))
-
-#define cpc_readb(port) (*(volatile ucchar *)(port))
-#define cpc_readw(port) (*(volatile ucshort *)(port))
-#define cpc_readl(port) (*(volatile uclong *)(port))
-
-#endif /* __KERNEL__ */
-
/****** Data Structures *****************************************************/
/*
* (memory mapped).
*/
struct RUNTIME_9050 {
- uclong loc_addr_range[4]; /* 00-0Ch : Local Address Ranges */
- uclong loc_rom_range; /* 10h : Local ROM Range */
- uclong loc_addr_base[4]; /* 14-20h : Local Address Base Addrs */
- uclong loc_rom_base; /* 24h : Local ROM Base */
- uclong loc_bus_descr[4]; /* 28-34h : Local Bus Descriptors */
- uclong rom_bus_descr; /* 38h : ROM Bus Descriptor */
- uclong cs_base[4]; /* 3C-48h : Chip Select Base Addrs */
- uclong intr_ctrl_stat; /* 4Ch : Interrupt Control/Status */
- uclong init_ctrl; /* 50h : EEPROM ctrl, Init Ctrl, etc */
+ u32 loc_addr_range[4]; /* 00-0Ch : Local Address Ranges */
+ u32 loc_rom_range; /* 10h : Local ROM Range */
+ u32 loc_addr_base[4]; /* 14-20h : Local Address Base Addrs */
+ u32 loc_rom_base; /* 24h : Local ROM Base */
+ u32 loc_bus_descr[4]; /* 28-34h : Local Bus Descriptors */
+ u32 rom_bus_descr; /* 38h : ROM Bus Descriptor */
+ u32 cs_base[4]; /* 3C-48h : Chip Select Base Addrs */
+ u32 intr_ctrl_stat; /* 4Ch : Interrupt Control/Status */
+ u32 init_ctrl; /* 50h : EEPROM ctrl, Init Ctrl, etc */
};
#define PLX_9050_LINT1_ENABLE 0x01
#define PC300_FALC_MAXLOOP 0x0000ffff /* for falc_issue_cmd() */
typedef struct falc {
- ucchar sync; /* If true FALC is synchronized */
- ucchar active; /* if TRUE then already active */
- ucchar loop_active; /* if TRUE a line loopback UP was received */
- ucchar loop_gen; /* if TRUE a line loopback UP was issued */
+ u8 sync; /* If true FALC is synchronized */
+ u8 active; /* if TRUE then already active */
+ u8 loop_active; /* if TRUE a line loopback UP was received */
+ u8 loop_gen; /* if TRUE a line loopback UP was issued */
- ucchar num_channels;
- ucchar offset; /* 1 for T1, 0 for E1 */
- ucchar full_bandwidth;
+ u8 num_channels;
+ u8 offset; /* 1 for T1, 0 for E1 */
+ u8 full_bandwidth;
- ucchar xmb_cause;
- ucchar multiframe_mode;
+ u8 xmb_cause;
+ u8 multiframe_mode;
/* Statistics */
- ucshort pden; /* Pulse Density violation count */
- ucshort los; /* Loss of Signal count */
- ucshort losr; /* Loss of Signal recovery count */
- ucshort lfa; /* Loss of frame alignment count */
- ucshort farec; /* Frame Alignment Recovery count */
- ucshort lmfa; /* Loss of multiframe alignment count */
- ucshort ais; /* Remote Alarm indication Signal count */
- ucshort sec; /* One-second timer */
- ucshort es; /* Errored second */
- ucshort rai; /* remote alarm received */
- ucshort bec;
- ucshort fec;
- ucshort cvc;
- ucshort cec;
- ucshort ebc;
+ u16 pden; /* Pulse Density violation count */
+ u16 los; /* Loss of Signal count */
+ u16 losr; /* Loss of Signal recovery count */
+ u16 lfa; /* Loss of frame alignment count */
+ u16 farec; /* Frame Alignment Recovery count */
+ u16 lmfa; /* Loss of multiframe alignment count */
+ u16 ais; /* Remote Alarm indication Signal count */
+ u16 sec; /* One-second timer */
+ u16 es; /* Errored second */
+ u16 rai; /* remote alarm received */
+ u16 bec;
+ u16 fec;
+ u16 cvc;
+ u16 cec;
+ u16 ebc;
/* Status */
- ucchar red_alarm;
- ucchar blue_alarm;
- ucchar loss_fa;
- ucchar yellow_alarm;
- ucchar loss_mfa;
- ucchar prbs;
+ u8 red_alarm;
+ u8 blue_alarm;
+ u8 loss_fa;
+ u8 yellow_alarm;
+ u8 loss_mfa;
+ u8 prbs;
} falc_t;
typedef struct falc_status {
- ucchar sync; /* If true FALC is synchronized */
- ucchar red_alarm;
- ucchar blue_alarm;
- ucchar loss_fa;
- ucchar yellow_alarm;
- ucchar loss_mfa;
- ucchar prbs;
+ u8 sync; /* If true FALC is synchronized */
+ u8 red_alarm;
+ u8 blue_alarm;
+ u8 loss_fa;
+ u8 yellow_alarm;
+ u8 loss_mfa;
+ u8 prbs;
} falc_status_t;
typedef struct rsv_x21_status {
- ucchar dcd;
- ucchar dsr;
- ucchar cts;
- ucchar rts;
- ucchar dtr;
+ u8 dcd;
+ u8 dsr;
+ u8 cts;
+ u8 rts;
+ u8 dtr;
} rsv_x21_status_t;
typedef struct pc300stats {
int hw_type;
- uclong line_on;
- uclong line_off;
+ u32 line_on;
+ u32 line_off;
struct net_device_stats gen_stats;
falc_t te_stats;
} pc300stats_t;
typedef struct pc300patterntst {
char patrntst_on; /* 0 - off; 1 - on; 2 - read num_errors */
- ucshort num_errors;
+ u16 num_errors;
} pc300patterntst_t;
typedef struct pc300dev {
- void *if_ptr; /* General purpose pointer */
struct pc300ch *chan;
- ucchar trace_on;
- uclong line_on; /* DCD(X.21, RSV) / sync(TE) change counters */
- uclong line_off;
-#ifdef __KERNEL__
+ u8 trace_on;
+ u32 line_on; /* DCD(X.21, RSV) / sync(TE) change counters */
+ u32 line_off;
char name[16];
struct net_device *dev;
-
- void *private;
- struct sk_buff *tx_skb;
- union { /* This union has all the protocol-specific structures */
- struct ppp_device pppdev;
- }ifu;
#ifdef CONFIG_PC300_MLPPP
void *cpc_tty; /* information to PC300 TTY driver */
#endif
-#endif /* __KERNEL__ */
}pc300dev_t;
typedef struct pc300hw {
int bus; /* Bus (PCI, PMC, etc.) */
int nchan; /* number of channels */
int irq; /* interrupt request level */
- uclong clock; /* Board clock */
- ucchar cpld_id; /* CPLD ID (TE only) */
- ucshort cpld_reg1; /* CPLD reg 1 (TE only) */
- ucshort cpld_reg2; /* CPLD reg 2 (TE only) */
- ucshort gpioc_reg; /* PLX GPIOC reg */
- ucshort intctl_reg; /* PLX Int Ctrl/Status reg */
- uclong iophys; /* PLX registers I/O base */
- uclong iosize; /* PLX registers I/O size */
- uclong plxphys; /* PLX registers MMIO base (physical) */
+ u32 clock; /* Board clock */
+ u8 cpld_id; /* CPLD ID (TE only) */
+ u16 cpld_reg1; /* CPLD reg 1 (TE only) */
+ u16 cpld_reg2; /* CPLD reg 2 (TE only) */
+ u16 gpioc_reg; /* PLX GPIOC reg */
+ u16 intctl_reg; /* PLX Int Ctrl/Status reg */
+ u32 iophys; /* PLX registers I/O base */
+ u32 iosize; /* PLX registers I/O size */
+ u32 plxphys; /* PLX registers MMIO base (physical) */
void __iomem * plxbase; /* PLX registers MMIO base (virtual) */
- uclong plxsize; /* PLX registers MMIO size */
- uclong scaphys; /* SCA registers MMIO base (physical) */
+ u32 plxsize; /* PLX registers MMIO size */
+ u32 scaphys; /* SCA registers MMIO base (physical) */
void __iomem * scabase; /* SCA registers MMIO base (virtual) */
- uclong scasize; /* SCA registers MMIO size */
- uclong ramphys; /* On-board RAM MMIO base (physical) */
+ u32 scasize; /* SCA registers MMIO size */
+ u32 ramphys; /* On-board RAM MMIO base (physical) */
void __iomem * rambase; /* On-board RAM MMIO base (virtual) */
- uclong alloc_ramsize; /* RAM MMIO size allocated by the PCI bridge */
- uclong ramsize; /* On-board RAM MMIO size */
- uclong falcphys; /* FALC registers MMIO base (physical) */
+ u32 alloc_ramsize; /* RAM MMIO size allocated by the PCI bridge */
+ u32 ramsize; /* On-board RAM MMIO size */
+ u32 falcphys; /* FALC registers MMIO base (physical) */
void __iomem * falcbase;/* FALC registers MMIO base (virtual) */
- uclong falcsize; /* FALC registers MMIO size */
+ u32 falcsize; /* FALC registers MMIO size */
} pc300hw_t;
typedef struct pc300chconf {
- sync_serial_settings phys_settings; /* Clock type/rate (in bps),
+ sync_serial_settings phys_settings; /* Clock type/rate (in bps),
loopback mode */
raw_hdlc_proto proto_settings; /* Encoding, parity (CRC) */
- uclong media; /* HW media (RS232, V.35, etc.) */
- uclong proto; /* Protocol (PPP, X.25, etc.) */
- ucchar monitor; /* Monitor mode (0 = off, !0 = on) */
+ u32 media; /* HW media (RS232, V.35, etc.) */
+ u32 proto; /* Protocol (PPP, X.25, etc.) */
/* TE-specific parameters */
- ucchar lcode; /* Line Code (AMI, B8ZS, etc.) */
- ucchar fr_mode; /* Frame Mode (ESF, D4, etc.) */
- ucchar lbo; /* Line Build Out */
- ucchar rx_sens; /* Rx Sensitivity (long- or short-haul) */
- uclong tslot_bitmap; /* bit[i]=1 => timeslot _i_ is active */
+ u8 lcode; /* Line Code (AMI, B8ZS, etc.) */
+ u8 fr_mode; /* Frame Mode (ESF, D4, etc.) */
+ u8 lbo; /* Line Build Out */
+ u8 rx_sens; /* Rx Sensitivity (long- or short-haul) */
+ u32 tslot_bitmap; /* bit[i]=1 => timeslot _i_ is active */
} pc300chconf_t;
typedef struct pc300ch {
int channel;
pc300dev_t d;
pc300chconf_t conf;
- ucchar tx_first_bd; /* First TX DMA block descr. w/ data */
- ucchar tx_next_bd; /* Next free TX DMA block descriptor */
- ucchar rx_first_bd; /* First free RX DMA block descriptor */
- ucchar rx_last_bd; /* Last free RX DMA block descriptor */
- ucchar nfree_tx_bd; /* Number of free TX DMA block descriptors */
- falc_t falc; /* FALC structure (TE only) */
+ u8 tx_first_bd; /* First TX DMA block descr. w/ data */
+ u8 tx_next_bd; /* Next free TX DMA block descriptor */
+ u8 rx_first_bd; /* First free RX DMA block descriptor */
+ u8 rx_last_bd; /* Last free RX DMA block descriptor */
+ u8 nfree_tx_bd; /* Number of free TX DMA block descriptors */
+ falc_t falc; /* FALC structure (TE only) */
} pc300ch_t;
typedef struct pc300 {
pc300hw_t hw; /* hardware config. */
pc300ch_t chan[PC300_MAXCHAN];
-#ifdef __KERNEL__
spinlock_t card_lock;
-#endif /* __KERNEL__ */
} pc300_t;
typedef struct pc300conf {
#define PC300_TX_QUEUE_LEN 100
#define PC300_DEF_MTU 1600
-#ifdef __KERNEL__
/* Function Prototypes */
-void tx_dma_start(pc300_t *, int);
int cpc_open(struct net_device *dev);
-int cpc_set_media(hdlc_device *, int);
-#endif /* __KERNEL__ */
#endif /* _PC300_H */
-
#include <linux/netdevice.h>
#include <linux/spinlock.h>
#include <linux/if.h>
-
-#include <net/syncppp.h>
#include <net/arp.h>
#include <asm/io.h>
static void tx_dma_buf_check(pc300_t *, int);
static void rx_dma_buf_check(pc300_t *, int);
static irqreturn_t cpc_intr(int, void *);
-static int clock_rate_calc(uclong, uclong, int *);
-static uclong detect_ram(pc300_t *);
+static int clock_rate_calc(u32, u32, int *);
+static u32 detect_ram(pc300_t *);
static void plx_init(pc300_t *);
static void cpc_trace(struct net_device *, struct sk_buff *, char);
static int cpc_attach(struct net_device *, unsigned short, unsigned short);
+ DMA_TX_BD_BASE + ch_factor * sizeof(pcsca_bd_t));
for (i = 0; i < N_DMA_TX_BUF; i++, ptdescr++) {
- cpc_writel(&ptdescr->next, (uclong) (DMA_TX_BD_BASE +
+ cpc_writel(&ptdescr->next, (u32)(DMA_TX_BD_BASE +
(ch_factor + ((i + 1) & (N_DMA_TX_BUF - 1))) * sizeof(pcsca_bd_t)));
- cpc_writel(&ptdescr->ptbuf,
- (uclong) (DMA_TX_BASE + (ch_factor + i) * BD_DEF_LEN));
+ cpc_writel(&ptdescr->ptbuf,
+ (u32)(DMA_TX_BASE + (ch_factor + i) * BD_DEF_LEN));
}
}
+ DMA_RX_BD_BASE + ch_factor * sizeof(pcsca_bd_t));
for (i = 0; i < N_DMA_RX_BUF; i++, ptdescr++) {
- cpc_writel(&ptdescr->next, (uclong) (DMA_RX_BD_BASE +
- (ch_factor + ((i + 1) & (N_DMA_RX_BUF - 1))) * sizeof(pcsca_bd_t)));
+ cpc_writel(&ptdescr->next, (u32)(DMA_RX_BD_BASE +
+ (ch_factor + ((i + 1) & (N_DMA_RX_BUF - 1))) * sizeof(pcsca_bd_t)));
cpc_writel(&ptdescr->ptbuf,
- (uclong) (DMA_RX_BASE + (ch_factor + i) * BD_DEF_LEN));
+ (u32)(DMA_RX_BASE + (ch_factor + i) * BD_DEF_LEN));
}
}
{
volatile pcsca_bd_t __iomem *ptdescr;
int i;
- ucshort first_bd = card->chan[ch].tx_first_bd;
- ucshort next_bd = card->chan[ch].tx_next_bd;
+ u16 first_bd = card->chan[ch].tx_first_bd;
+ u16 next_bd = card->chan[ch].tx_next_bd;
printk("#CH%d: f_bd = %d(0x%08zx), n_bd = %d(0x%08zx)\n", ch,
first_bd, TX_BD_ADDR(ch, first_bd),
{
volatile pcsca_bd_t __iomem *ptdescr;
int i;
- ucshort first_bd = card->chan[ch].tx_first_bd;
- ucshort next_bd = card->chan[ch].tx_next_bd;
- uclong scabase = card->hw.scabase;
+ u16 first_bd = card->chan[ch].tx_first_bd;
+ u16 next_bd = card->chan[ch].tx_next_bd;
+ u32 scabase = card->hw.scabase;
printk ("\nnfree_tx_bd = %d \n", card->chan[ch].nfree_tx_bd);
printk("#CH%d: f_bd = %d(0x%08x), n_bd = %d(0x%08x)\n", ch,
printk("\n");
}
#endif
-
+
static void rx_dma_buf_check(pc300_t * card, int ch)
{
volatile pcsca_bd_t __iomem *ptdescr;
int i;
- ucshort first_bd = card->chan[ch].rx_first_bd;
- ucshort last_bd = card->chan[ch].rx_last_bd;
+ u16 first_bd = card->chan[ch].rx_first_bd;
+ u16 last_bd = card->chan[ch].rx_last_bd;
int ch_factor;
ch_factor = ch * N_DMA_RX_BUF;
static int dma_get_rx_frame_size(pc300_t * card, int ch)
{
volatile pcsca_bd_t __iomem *ptdescr;
- ucshort first_bd = card->chan[ch].rx_first_bd;
+ u16 first_bd = card->chan[ch].rx_first_bd;
int rcvd = 0;
- volatile ucchar status;
+ volatile u8 status;
ptdescr = (card->hw.rambase + RX_BD_ADDR(ch, first_bd));
while ((status = cpc_readb(&ptdescr->status)) & DST_OSB) {
* dma_buf_write: writes a frame to the Tx DMA buffers
* NOTE: this function writes one frame at a time.
*/
-static int dma_buf_write(pc300_t * card, int ch, ucchar * ptdata, int len)
+static int dma_buf_write(pc300_t *card, int ch, u8 *ptdata, int len)
{
int i, nchar;
volatile pcsca_bd_t __iomem *ptdescr;
int tosend = len;
- ucchar nbuf = ((len - 1) / BD_DEF_LEN) + 1;
+ u8 nbuf = ((len - 1) / BD_DEF_LEN) + 1;
if (nbuf >= card->chan[ch].nfree_tx_bd) {
return -ENOMEM;
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
volatile pcsca_bd_t __iomem *ptdescr;
int rcvd = 0;
- volatile ucchar status;
+ volatile u8 status;
ptdescr = (card->hw.rambase +
RX_BD_ADDR(ch, chan->rx_first_bd));
static void tx_dma_stop(pc300_t * card, int ch)
{
void __iomem *scabase = card->hw.scabase;
- ucchar drr_ena_bit = 1 << (5 + 2 * ch);
- ucchar drr_rst_bit = 1 << (1 + 2 * ch);
+ u8 drr_ena_bit = 1 << (5 + 2 * ch);
+ u8 drr_rst_bit = 1 << (1 + 2 * ch);
/* Disable DMA */
cpc_writeb(scabase + DRR, drr_ena_bit);
static void rx_dma_stop(pc300_t * card, int ch)
{
void __iomem *scabase = card->hw.scabase;
- ucchar drr_ena_bit = 1 << (4 + 2 * ch);
- ucchar drr_rst_bit = 1 << (2 * ch);
+ u8 drr_ena_bit = 1 << (4 + 2 * ch);
+ u8 drr_rst_bit = 1 << (2 * ch);
/* Disable DMA */
cpc_writeb(scabase + DRR, drr_ena_bit);
/*************************/
/*** FALC Routines ***/
/*************************/
-static void falc_issue_cmd(pc300_t * card, int ch, ucchar cmd)
+static void falc_issue_cmd(pc300_t *card, int ch, u8 cmd)
{
void __iomem *falcbase = card->hw.falcbase;
unsigned long i = 0;
static void falc_open_timeslot(pc300_t * card, int ch, int timeslot)
{
void __iomem *falcbase = card->hw.falcbase;
- ucchar tshf = card->chan[ch].falc.offset;
+ u8 tshf = card->chan[ch].falc.offset;
cpc_writeb(falcbase + F_REG((ICB1 + (timeslot - tshf) / 8), ch),
cpc_readb(falcbase + F_REG((ICB1 + (timeslot - tshf) / 8), ch)) &
static void falc_close_timeslot(pc300_t * card, int ch, int timeslot)
{
void __iomem *falcbase = card->hw.falcbase;
- ucchar tshf = card->chan[ch].falc.offset;
+ u8 tshf = card->chan[ch].falc.offset;
cpc_writeb(falcbase + F_REG((ICB1 + (timeslot - tshf) / 8), ch),
cpc_readb(falcbase + F_REG((ICB1 + (timeslot - tshf) / 8), ch)) |
pc300chconf_t *conf = (pc300chconf_t *) & chan->conf;
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucchar dja = (ch ? (LIM2_DJA2 | LIM2_DJA1) : 0);
+ u8 dja = (ch ? (LIM2_DJA2 | LIM2_DJA1) : 0);
/* Switch to T1 mode (PCM 24) */
cpc_writeb(falcbase + F_REG(FMR1, ch), FMR1_PMOD);
pc300chconf_t *conf = (pc300chconf_t *) & chan->conf;
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucchar dja = (ch ? (LIM2_DJA2 | LIM2_DJA1) : 0);
+ u8 dja = (ch ? (LIM2_DJA2 | LIM2_DJA1) : 0);
/* Switch to E1 mode (PCM 30) */
cpc_writeb(falcbase + F_REG(FMR1, ch),
pc300chconf_t *conf = (pc300chconf_t *) & chan->conf;
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucchar dummy;
+ u8 dummy;
unsigned long flags;
memset(pfalc, 0, sizeof(falc_t));
pc300chconf_t *conf = (pc300chconf_t *) & chan->conf;
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucshort counter;
+ u16 counter;
counter = cpc_readb(falcbase + F_REG(FECL, ch));
counter |= cpc_readb(falcbase + F_REG(FECH, ch)) << 8;
* Description: This routine returns the bit error counter value
*----------------------------------------------------------------------------
*/
-static ucshort falc_pattern_test_error(pc300_t * card, int ch)
+static u16 falc_pattern_test_error(pc300_t * card, int ch)
{
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
falc_t *pfalc = (falc_t *) & chan->falc;
pc300_t *card = (pc300_t *) chan->card;
int ch = chan->channel;
unsigned long flags;
- ucchar ilar;
+ u8 ilar;
dev->stats.tx_errors++;
dev->stats.tx_aborted_errors++;
int i;
#endif
- if (chan->conf.monitor) {
- /* In monitor mode no Tx is done: ignore packet */
- dev_kfree_skb(skb);
- return 0;
- } else if (!netif_carrier_ok(dev)) {
+ if (!netif_carrier_ok(dev)) {
/* DCD must be OFF: drop packet */
dev_kfree_skb(skb);
dev->stats.tx_errors++;
}
/* Write buffer to DMA buffers */
- if (dma_buf_write(card, ch, (ucchar *) skb->data, skb->len) != 0) {
+ if (dma_buf_write(card, ch, (u8 *)skb->data, skb->len) != 0) {
// printk("%s: write error. Dropping TX packet.\n", dev->name);
netif_stop_queue(dev);
dev_kfree_skb(skb);
static void sca_intr(pc300_t * card)
{
void __iomem *scabase = card->hw.scabase;
- volatile uclong status;
+ volatile u32 status;
int ch;
int intr_count = 0;
unsigned char dsr_rx;
/**** Reception ****/
if (status & IR0_DRX((IR0_DMIA | IR0_DMIB), ch)) {
- ucchar drx_stat = cpc_readb(scabase + DSR_RX(ch));
+ u8 drx_stat = cpc_readb(scabase + DSR_RX(ch));
/* Clear RX interrupts */
cpc_writeb(scabase + DSR_RX(ch), drx_stat | DSR_DWE);
/**** Transmission ****/
if (status & IR0_DTX((IR0_EFT | IR0_DMIA | IR0_DMIB), ch)) {
- ucchar dtx_stat = cpc_readb(scabase + DSR_TX(ch));
+ u8 dtx_stat = cpc_readb(scabase + DSR_TX(ch));
/* Clear TX interrupts */
cpc_writeb(scabase + DSR_TX(ch), dtx_stat | DSR_DWE);
/**** MSCI ****/
if (status & IR0_M(IR0_RXINTA, ch)) {
- ucchar st1 = cpc_readb(scabase + M_REG(ST1, ch));
+ u8 st1 = cpc_readb(scabase + M_REG(ST1, ch));
/* Clear MSCI interrupts */
cpc_writeb(scabase + M_REG(ST1, ch), st1);
}
}
-static void falc_t1_loop_detection(pc300_t * card, int ch, ucchar frs1)
+static void falc_t1_loop_detection(pc300_t *card, int ch, u8 frs1)
{
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
falc_t *pfalc = (falc_t *) & chan->falc;
}
}
-static void falc_e1_loop_detection(pc300_t * card, int ch, ucchar rsp)
+static void falc_e1_loop_detection(pc300_t *card, int ch, u8 rsp)
{
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
falc_t *pfalc = (falc_t *) & chan->falc;
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucchar isr0, isr3, gis;
- ucchar dummy;
+ u8 isr0, isr3, gis;
+ u8 dummy;
while ((gis = cpc_readb(falcbase + F_REG(GIS, ch))) != 0) {
if (gis & GIS_ISR0) {
pc300ch_t *chan = (pc300ch_t *) & card->chan[ch];
falc_t *pfalc = (falc_t *) & chan->falc;
void __iomem *falcbase = card->hw.falcbase;
- ucchar isr1, isr2, isr3, gis, rsp;
- ucchar dummy;
+ u8 isr1, isr2, isr3, gis, rsp;
+ u8 dummy;
while ((gis = cpc_readb(falcbase + F_REG(GIS, ch))) != 0) {
rsp = cpc_readb(falcbase + F_REG(RSP, ch));
static irqreturn_t cpc_intr(int irq, void *dev_id)
{
pc300_t *card = dev_id;
- volatile ucchar plx_status;
+ volatile u8 plx_status;
if (!card) {
#ifdef PC300_DEBUG_INTR
static void cpc_sca_status(pc300_t * card, int ch)
{
- ucchar ilar;
+ u8 ilar;
void __iomem *scabase = card->hw.scabase;
unsigned long flags;
}
}
-static int clock_rate_calc(uclong rate, uclong clock, int *br_io)
+static int clock_rate_calc(u32 rate, u32 clock, int *br_io)
{
int br, tc;
int br_pwr, error;
void __iomem *scabase = card->hw.scabase;
void __iomem *plxbase = card->hw.plxbase;
int ch = chan->channel;
- uclong clkrate = chan->conf.phys_settings.clock_rate;
- uclong clktype = chan->conf.phys_settings.clock_type;
- ucshort encoding = chan->conf.proto_settings.encoding;
- ucshort parity = chan->conf.proto_settings.parity;
- ucchar md0, md2;
-
+ u32 clkrate = chan->conf.phys_settings.clock_rate;
+ u32 clktype = chan->conf.phys_settings.clock_type;
+ u16 encoding = chan->conf.proto_settings.encoding;
+ u16 parity = chan->conf.proto_settings.parity;
+ u8 md0, md2;
+
/* Reset the channel */
cpc_writeb(scabase + M_REG(CMD, ch), CMD_CH_RST);
printk("pc300: cpc_open");
#endif
-#ifdef FIXME
- if (hdlc->proto.id == IF_PROTO_PPP) {
- d->if_ptr = &hdlc->state.ppp.pppdev;
- }
-#endif
-
result = hdlc_open(dev);
- if (/* FIXME hdlc->proto.id == IF_PROTO_PPP*/ 0) {
- dev->priv = d;
- }
- if (result) {
+
+ if (result)
return result;
- }
sprintf(ifr.ifr_name, "%s", dev->name);
result = cpc_opench(d);
CPC_UNLOCK(card, flags);
hdlc_close(dev);
- if (/* FIXME hdlc->proto.id == IF_PROTO_PPP*/ 0) {
- d->if_ptr = NULL;
- }
+
#ifdef CONFIG_PC300_MLPPP
if (chan->conf.proto == PC300_PROTO_MLPPP) {
cpc_tty_unregister_service(d);
return 0;
}
-static uclong detect_ram(pc300_t * card)
+static u32 detect_ram(pc300_t * card)
{
- uclong i;
- ucchar data;
+ u32 i;
+ u8 data;
void __iomem *rambase = card->hw.rambase;
card->hw.ramsize = PC300_RAMSIZE;
/* Let's find out how much RAM is present on this board */
for (i = 0; i < card->hw.ramsize; i++) {
- data = (ucchar) (i & 0xff);
+ data = (u8)(i & 0xff);
cpc_writeb(rambase + i, data);
if (cpc_readb(rambase + i) != data) {
break;
cpc_writeb(card->hw.scabase + DMER, 0x80);
if (card->hw.type == PC300_TE) {
- ucchar reg1;
+ u8 reg1;
/* Check CPLD version */
reg1 = cpc_readb(card->hw.falcbase + CPLD_REG1);
chan->nfree_tx_bd = N_DMA_TX_BUF;
d->chan = chan;
- d->tx_skb = NULL;
d->trace_on = 0;
d->line_on = 0;
d->line_off = 0;
{
static int first_time = 1;
int err, eeprom_outdated = 0;
- ucshort device_id;
+ u16 device_id;
pc300_t *card;
if (first_time) {
*
* (c) Copyright 1999, 2001 Alan Cox
* (c) Copyright 2001 Red Hat Inc.
+ * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
*
*/
#include <linux/netdevice.h>
#include <linux/if_arp.h>
#include <linux/delay.h>
+#include <linux/hdlc.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <net/arp.h>
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/byteorder.h>
-#include <net/syncppp.h>
#include "z85230.h"
struct slvl_device
{
- void *if_ptr; /* General purpose pointer (used by SPPP) */
struct z8530_channel *chan;
- struct ppp_device pppdev;
int channel;
};
struct slvl_board
{
- struct slvl_device *dev[2];
+ struct slvl_device dev[2];
struct z8530_dev board;
int iobase;
};
* Network driver support routines
*/
+static inline struct slvl_device* dev_to_chan(struct net_device *dev)
+{
+ return (struct slvl_device *)dev_to_hdlc(dev)->priv;
+}
+
/*
- * Frame receive. Simple for our card as we do sync ppp and there
+ * Frame receive. Simple for our card as we do HDLC and there
* is no funny garbage involved
*/
-
+
static void sealevel_input(struct z8530_channel *c, struct sk_buff *skb)
{
/* Drop the CRC - it's not a good idea to try and negotiate it ;) */
- skb_trim(skb, skb->len-2);
- skb->protocol=htons(ETH_P_WAN_PPP);
+ skb_trim(skb, skb->len - 2);
+ skb->protocol = hdlc_type_trans(skb, c->netdevice);
skb_reset_mac_header(skb);
- skb->dev=c->netdevice;
- /*
- * Send it to the PPP layer. We don't have time to process
- * it right now.
- */
+ skb->dev = c->netdevice;
netif_rx(skb);
c->netdevice->last_rx = jiffies;
}
-
+
/*
* We've been placed in the UP state
- */
-
+ */
+
static int sealevel_open(struct net_device *d)
{
- struct slvl_device *slvl=d->priv;
+ struct slvl_device *slvl = dev_to_chan(d);
int err = -1;
int unit = slvl->channel;
-
+
/*
- * Link layer up.
+ * Link layer up.
*/
- switch(unit)
+ switch (unit)
{
case 0:
- err=z8530_sync_dma_open(d, slvl->chan);
+ err = z8530_sync_dma_open(d, slvl->chan);
break;
case 1:
- err=z8530_sync_open(d, slvl->chan);
+ err = z8530_sync_open(d, slvl->chan);
break;
}
-
- if(err)
+
+ if (err)
return err;
- /*
- * Begin PPP
- */
- err=sppp_open(d);
- if(err)
- {
- switch(unit)
- {
+
+ err = hdlc_open(d);
+ if (err) {
+ switch (unit) {
case 0:
z8530_sync_dma_close(d, slvl->chan);
break;
case 1:
z8530_sync_close(d, slvl->chan);
break;
- }
+ }
return err;
}
-
- slvl->chan->rx_function=sealevel_input;
-
+
+ slvl->chan->rx_function = sealevel_input;
+
/*
* Go go go
*/
static int sealevel_close(struct net_device *d)
{
- struct slvl_device *slvl=d->priv;
+ struct slvl_device *slvl = dev_to_chan(d);
int unit = slvl->channel;
-
+
/*
* Discard new frames
*/
-
- slvl->chan->rx_function=z8530_null_rx;
-
- /*
- * PPP off
- */
- sppp_close(d);
- /*
- * Link layer down
- */
+ slvl->chan->rx_function = z8530_null_rx;
+
+ hdlc_close(d);
netif_stop_queue(d);
-
- switch(unit)
+
+ switch (unit)
{
case 0:
z8530_sync_dma_close(d, slvl->chan);
static int sealevel_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
{
- /* struct slvl_device *slvl=d->priv;
+ /* struct slvl_device *slvl=dev_to_chan(d);
z8530_ioctl(d,&slvl->sync.chanA,ifr,cmd) */
- return sppp_do_ioctl(d, ifr,cmd);
-}
-
-static struct net_device_stats *sealevel_get_stats(struct net_device *d)
-{
- struct slvl_device *slvl=d->priv;
- if(slvl)
- return z8530_get_stats(slvl->chan);
- else
- return NULL;
+ return hdlc_ioctl(d, ifr, cmd);
}
/*
- * Passed PPP frames, fire them downwind.
+ * Passed network frames, fire them downwind.
*/
-
+
static int sealevel_queue_xmit(struct sk_buff *skb, struct net_device *d)
{
- struct slvl_device *slvl=d->priv;
- return z8530_queue_xmit(slvl->chan, skb);
+ return z8530_queue_xmit(dev_to_chan(d)->chan, skb);
}
-static int sealevel_neigh_setup(struct neighbour *n)
+static int sealevel_attach(struct net_device *dev, unsigned short encoding,
+ unsigned short parity)
{
- if (n->nud_state == NUD_NONE) {
- n->ops = &arp_broken_ops;
- n->output = n->ops->output;
- }
- return 0;
+ if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
+ return 0;
+ return -EINVAL;
}
-static int sealevel_neigh_setup_dev(struct net_device *dev, struct neigh_parms *p)
+static int slvl_setup(struct slvl_device *sv, int iobase, int irq)
{
- if (p->tbl->family == AF_INET) {
- p->neigh_setup = sealevel_neigh_setup;
- p->ucast_probes = 0;
- p->mcast_probes = 0;
+ struct net_device *dev = alloc_hdlcdev(sv);
+ if (!dev)
+ return -1;
+
+ dev_to_hdlc(dev)->attach = sealevel_attach;
+ dev_to_hdlc(dev)->xmit = sealevel_queue_xmit;
+ dev->open = sealevel_open;
+ dev->stop = sealevel_close;
+ dev->do_ioctl = sealevel_ioctl;
+ dev->base_addr = iobase;
+ dev->irq = irq;
+
+ if (register_hdlc_device(dev)) {
+ printk(KERN_ERR "sealevel: unable to register HDLC device\n");
+ free_netdev(dev);
+ return -1;
}
- return 0;
-}
-static int sealevel_attach(struct net_device *dev)
-{
- struct slvl_device *sv = dev->priv;
- sppp_attach(&sv->pppdev);
+ sv->chan->netdevice = dev;
return 0;
}
-static void sealevel_detach(struct net_device *dev)
-{
- sppp_detach(dev);
-}
-
-static void slvl_setup(struct net_device *d)
-{
- d->open = sealevel_open;
- d->stop = sealevel_close;
- d->init = sealevel_attach;
- d->uninit = sealevel_detach;
- d->hard_start_xmit = sealevel_queue_xmit;
- d->get_stats = sealevel_get_stats;
- d->set_multicast_list = NULL;
- d->do_ioctl = sealevel_ioctl;
- d->neigh_setup = sealevel_neigh_setup_dev;
- d->set_mac_address = NULL;
-
-}
-
-static inline struct slvl_device *slvl_alloc(int iobase, int irq)
-{
- struct net_device *d;
- struct slvl_device *sv;
-
- d = alloc_netdev(sizeof(struct slvl_device), "hdlc%d",
- slvl_setup);
-
- if (!d)
- return NULL;
-
- sv = d->priv;
- d->ml_priv = sv;
- sv->if_ptr = &sv->pppdev;
- sv->pppdev.dev = d;
- d->base_addr = iobase;
- d->irq = irq;
-
- return sv;
-}
-
/*
* Allocate and setup Sealevel board.
*/
-
-static __init struct slvl_board *slvl_init(int iobase, int irq,
+
+static __init struct slvl_board *slvl_init(int iobase, int irq,
int txdma, int rxdma, int slow)
{
struct z8530_dev *dev;
struct slvl_board *b;
-
+
/*
* Get the needed I/O space
*/
- if(!request_region(iobase, 8, "Sealevel 4021"))
- {
- printk(KERN_WARNING "sealevel: I/O 0x%X already in use.\n", iobase);
+ if (!request_region(iobase, 8, "Sealevel 4021")) {
+ printk(KERN_WARNING "sealevel: I/O 0x%X already in use.\n",
+ iobase);
return NULL;
}
-
- b = kzalloc(sizeof(struct slvl_board), GFP_KERNEL);
- if(!b)
- goto fail3;
- if (!(b->dev[0]= slvl_alloc(iobase, irq)))
- goto fail2;
+ b = kzalloc(sizeof(struct slvl_board), GFP_KERNEL);
+ if (!b)
+ goto err_kzalloc;
- b->dev[0]->chan = &b->board.chanA;
- b->dev[0]->channel = 0;
-
- if (!(b->dev[1] = slvl_alloc(iobase, irq)))
- goto fail1_0;
+ b->dev[0].chan = &b->board.chanA;
+ b->dev[0].channel = 0;
- b->dev[1]->chan = &b->board.chanB;
- b->dev[1]->channel = 1;
+ b->dev[1].chan = &b->board.chanB;
+ b->dev[1].channel = 1;
dev = &b->board;
-
+
/*
* Stuff in the I/O addressing
*/
-
+
dev->active = 0;
b->iobase = iobase;
-
+
/*
* Select 8530 delays for the old board
*/
-
- if(slow)
+
+ if (slow)
iobase |= Z8530_PORT_SLEEP;
-
- dev->chanA.ctrlio=iobase+1;
- dev->chanA.dataio=iobase;
- dev->chanB.ctrlio=iobase+3;
- dev->chanB.dataio=iobase+2;
-
- dev->chanA.irqs=&z8530_nop;
- dev->chanB.irqs=&z8530_nop;
-
+
+ dev->chanA.ctrlio = iobase + 1;
+ dev->chanA.dataio = iobase;
+ dev->chanB.ctrlio = iobase + 3;
+ dev->chanB.dataio = iobase + 2;
+
+ dev->chanA.irqs = &z8530_nop;
+ dev->chanB.irqs = &z8530_nop;
+
/*
* Assert DTR enable DMA
*/
-
- outb(3|(1<<7), b->iobase+4);
-
+
+ outb(3 | (1 << 7), b->iobase + 4);
+
/* We want a fast IRQ for this device. Actually we'd like an even faster
IRQ ;) - This is one driver RtLinux is made for */
-
- if(request_irq(irq, &z8530_interrupt, IRQF_DISABLED, "SeaLevel", dev)<0)
- {
+
+ if (request_irq(irq, &z8530_interrupt, IRQF_DISABLED,
+ "SeaLevel", dev) < 0) {
printk(KERN_WARNING "sealevel: IRQ %d already in use.\n", irq);
- goto fail1_1;
+ goto err_request_irq;
}
-
- dev->irq=irq;
- dev->chanA.private=&b->dev[0];
- dev->chanB.private=&b->dev[1];
- dev->chanA.netdevice=b->dev[0]->pppdev.dev;
- dev->chanB.netdevice=b->dev[1]->pppdev.dev;
- dev->chanA.dev=dev;
- dev->chanB.dev=dev;
-
- dev->chanA.txdma=3;
- dev->chanA.rxdma=1;
- if(request_dma(dev->chanA.txdma, "SeaLevel (TX)")!=0)
- goto fail;
-
- if(request_dma(dev->chanA.rxdma, "SeaLevel (RX)")!=0)
- goto dmafail;
-
+
+ dev->irq = irq;
+ dev->chanA.private = &b->dev[0];
+ dev->chanB.private = &b->dev[1];
+ dev->chanA.dev = dev;
+ dev->chanB.dev = dev;
+
+ dev->chanA.txdma = 3;
+ dev->chanA.rxdma = 1;
+ if (request_dma(dev->chanA.txdma, "SeaLevel (TX)"))
+ goto err_dma_tx;
+
+ if (request_dma(dev->chanA.rxdma, "SeaLevel (RX)"))
+ goto err_dma_rx;
+
disable_irq(irq);
-
+
/*
* Begin normal initialise
*/
-
- if(z8530_init(dev)!=0)
- {
+
+ if (z8530_init(dev) != 0) {
printk(KERN_ERR "Z8530 series device not found.\n");
enable_irq(irq);
- goto dmafail2;
+ goto free_hw;
}
- if(dev->type==Z85C30)
- {
+ if (dev->type == Z85C30) {
z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream);
z8530_channel_load(&dev->chanB, z8530_hdlc_kilostream);
- }
- else
- {
+ } else {
z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream_85230);
z8530_channel_load(&dev->chanB, z8530_hdlc_kilostream_85230);
}
/*
* Now we can take the IRQ
*/
-
+
enable_irq(irq);
- if (register_netdev(b->dev[0]->pppdev.dev))
- goto dmafail2;
-
- if (register_netdev(b->dev[1]->pppdev.dev))
- goto fail_unit;
+ if (slvl_setup(&b->dev[0], iobase, irq))
+ goto free_hw;
+ if (slvl_setup(&b->dev[1], iobase, irq))
+ goto free_netdev0;
z8530_describe(dev, "I/O", iobase);
- dev->active=1;
+ dev->active = 1;
return b;
-fail_unit:
- unregister_netdev(b->dev[0]->pppdev.dev);
-
-dmafail2:
+free_netdev0:
+ unregister_hdlc_device(b->dev[0].chan->netdevice);
+ free_netdev(b->dev[0].chan->netdevice);
+free_hw:
free_dma(dev->chanA.rxdma);
-dmafail:
+err_dma_rx:
free_dma(dev->chanA.txdma);
-fail:
+err_dma_tx:
free_irq(irq, dev);
-fail1_1:
- free_netdev(b->dev[1]->pppdev.dev);
-fail1_0:
- free_netdev(b->dev[0]->pppdev.dev);
-fail2:
+err_request_irq:
kfree(b);
-fail3:
- release_region(iobase,8);
+err_kzalloc:
+ release_region(iobase, 8);
return NULL;
}
int u;
z8530_shutdown(&b->board);
-
- for(u=0; u<2; u++)
+
+ for (u = 0; u < 2; u++)
{
- struct net_device *d = b->dev[u]->pppdev.dev;
- unregister_netdev(d);
+ struct net_device *d = b->dev[u].chan->netdevice;
+ unregister_hdlc_device(d);
free_netdev(d);
}
-
+
free_irq(b->board.irq, &b->board);
free_dma(b->board.chanA.rxdma);
free_dma(b->board.chanA.txdma);
static int __init slvl_init_module(void)
{
-#ifdef MODULE
- printk(KERN_INFO "SeaLevel Z85230 Synchronous Driver v 0.02.\n");
- printk(KERN_INFO "(c) Copyright 1998, Building Number Three Ltd.\n");
-#endif
slvl_unit = slvl_init(io, irq, txdma, rxdma, slow);
return slvl_unit ? 0 : -ENODEV;
skb->dev=dev;
skb_reset_mac_header(skb);
- if (dev->flags & IFF_RUNNING)
- {
- /* Count received bytes, add FCS and one flag */
- sp->ibytes+= skb->len + 3;
- sp->ipkts++;
- }
-
if (!pskb_may_pull(skb, PPP_HEADER_LEN)) {
/* Too small packet, drop it. */
if (sp->pp_flags & PP_DEBUG)
sppp_print_bytes ((u8*) (lh+1), len);
printk (">\n");
}
- sp->obytes += skb->len;
/* Control is high priority so it doesn't get queued behind data */
skb->priority=TC_PRIO_CONTROL;
skb->dev = dev;
printk (KERN_WARNING "%s: cisco output: <%xh %xh %xh %xh %xh-%xh>\n",
dev->name, ntohl (ch->type), ch->par1,
ch->par2, ch->rel, ch->time0, ch->time1);
- sp->obytes += skb->len;
skb->priority=TC_PRIO_CONTROL;
skb->dev = dev;
skb_queue_tail(&tx_queue, skb);
#include <linux/netdevice.h>
#include <linux/if_arp.h>
#include <linux/delay.h>
+#include <linux/hdlc.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <asm/dma.h>
#define RT_UNLOCK
#include <linux/spinlock.h>
-#include <net/syncppp.h>
#include "z85230.h"
* A status event occurred in PIO synchronous mode. There are several
* reasons the chip will bother us here. A transmit underrun means we
* failed to feed the chip fast enough and just broke a packet. A DCD
- * change is a line up or down. We communicate that back to the protocol
- * layer for synchronous PPP to renegotiate.
+ * change is a line up or down.
*/
static void z8530_status(struct z8530_channel *chan)
{
u8 status, altered;
- status=read_zsreg(chan, R0);
- altered=chan->status^status;
-
- chan->status=status;
-
- if(status&TxEOM)
- {
+ status = read_zsreg(chan, R0);
+ altered = chan->status ^ status;
+
+ chan->status = status;
+
+ if (status & TxEOM) {
/* printk("%s: Tx underrun.\n", chan->dev->name); */
- chan->stats.tx_fifo_errors++;
+ chan->netdevice->stats.tx_fifo_errors++;
write_zsctrl(chan, ERR_RES);
z8530_tx_done(chan);
}
-
- if(altered&chan->dcdcheck)
+
+ if (altered & chan->dcdcheck)
{
- if(status&chan->dcdcheck)
- {
+ if (status & chan->dcdcheck) {
printk(KERN_INFO "%s: DCD raised\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3]|RxENABLE);
- if(chan->netdevice &&
- ((chan->netdevice->type == ARPHRD_HDLC) ||
- (chan->netdevice->type == ARPHRD_PPP)))
- sppp_reopen(chan->netdevice);
- }
- else
- {
+ write_zsreg(chan, R3, chan->regs[3] | RxENABLE);
+ if (chan->netdevice)
+ netif_carrier_on(chan->netdevice);
+ } else {
printk(KERN_INFO "%s: DCD lost\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3]&~RxENABLE);
+ write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE);
z8530_flush_fifo(chan);
+ if (chan->netdevice)
+ netif_carrier_off(chan->netdevice);
}
-
- }
+
+ }
write_zsctrl(chan, RES_EXT_INT);
write_zsctrl(chan, RES_H_IUS);
}
-struct z8530_irqhandler z8530_sync=
+struct z8530_irqhandler z8530_sync =
{
z8530_rx,
z8530_tx,
*
* A status event occurred on the Z8530. We receive these for two reasons
* when in DMA mode. Firstly if we finished a packet transfer we get one
- * and kick the next packet out. Secondly we may see a DCD change and
- * have to poke the protocol layer.
+ * and kick the next packet out. Secondly we may see a DCD change.
*
*/
}
}
- if(altered&chan->dcdcheck)
+ if (altered & chan->dcdcheck)
{
- if(status&chan->dcdcheck)
- {
+ if (status & chan->dcdcheck) {
printk(KERN_INFO "%s: DCD raised\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3]|RxENABLE);
- if(chan->netdevice &&
- ((chan->netdevice->type == ARPHRD_HDLC) ||
- (chan->netdevice->type == ARPHRD_PPP)))
- sppp_reopen(chan->netdevice);
- }
- else
- {
+ write_zsreg(chan, R3, chan->regs[3] | RxENABLE);
+ if (chan->netdevice)
+ netif_carrier_on(chan->netdevice);
+ } else {
printk(KERN_INFO "%s:DCD lost\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3]&~RxENABLE);
+ write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE);
z8530_flush_fifo(chan);
+ if (chan->netdevice)
+ netif_carrier_off(chan->netdevice);
}
- }
+ }
write_zsctrl(chan, RES_EXT_INT);
write_zsctrl(chan, RES_H_IUS);
/*
* Check if we crapped out.
*/
- if(get_dma_residue(c->txdma))
+ if (get_dma_residue(c->txdma))
{
- c->stats.tx_dropped++;
- c->stats.tx_fifo_errors++;
+ c->netdevice->stats.tx_dropped++;
+ c->netdevice->stats.tx_fifo_errors++;
}
release_dma_lock(flags);
}
* packet. This code is fairly timing sensitive.
*
* Called with the register lock held.
- */
-
+ */
+
static void z8530_tx_done(struct z8530_channel *c)
{
struct sk_buff *skb;
/* Actually this can happen.*/
- if(c->tx_skb==NULL)
+ if (c->tx_skb == NULL)
return;
- skb=c->tx_skb;
- c->tx_skb=NULL;
+ skb = c->tx_skb;
+ c->tx_skb = NULL;
z8530_tx_begin(c);
- c->stats.tx_packets++;
- c->stats.tx_bytes+=skb->len;
+ c->netdevice->stats.tx_packets++;
+ c->netdevice->stats.tx_bytes += skb->len;
dev_kfree_skb_irq(skb);
}
* @skb: The buffer
*
* We point the receive handler at this function when idle. Instead
- * of syncppp processing the frames we get to throw them away.
+ * of processing the frames we get to throw them away.
*/
void z8530_null_rx(struct z8530_channel *c, struct sk_buff *skb)
else
/* Can't occur as we dont reenable the DMA irq until
after the flip is done */
- printk(KERN_WARNING "%s: DMA flip overrun!\n", c->netdevice->name);
-
+ printk(KERN_WARNING "%s: DMA flip overrun!\n",
+ c->netdevice->name);
+
release_dma_lock(flags);
-
+
/*
* Shove the old buffer into an sk_buff. We can't DMA
* directly into one on a PC - it might be above the 16Mb
* can avoid the copy. Optimisation 2 - make the memcpy
* a copychecksum.
*/
-
- skb=dev_alloc_skb(ct);
- if(skb==NULL)
- {
- c->stats.rx_dropped++;
- printk(KERN_WARNING "%s: Memory squeeze.\n", c->netdevice->name);
- }
- else
- {
+
+ skb = dev_alloc_skb(ct);
+ if (skb == NULL) {
+ c->netdevice->stats.rx_dropped++;
+ printk(KERN_WARNING "%s: Memory squeeze.\n",
+ c->netdevice->name);
+ } else {
skb_put(skb, ct);
skb_copy_to_linear_data(skb, rxb, ct);
- c->stats.rx_packets++;
- c->stats.rx_bytes+=ct;
+ c->netdevice->stats.rx_packets++;
+ c->netdevice->stats.rx_bytes += ct;
}
- c->dma_ready=1;
- }
- else
- {
- RT_LOCK;
- skb=c->skb;
-
+ c->dma_ready = 1;
+ } else {
+ RT_LOCK;
+ skb = c->skb;
+
/*
* The game we play for non DMA is similar. We want to
* get the controller set up for the next packet as fast
* if you build a system where the sync irq isnt blocked
* by the kernel IRQ disable then you need only block the
* sync IRQ for the RT_LOCK area.
- *
+ *
*/
ct=c->count;
-
+
c->skb = c->skb2;
c->count = 0;
c->max = c->mtu;
- if(c->skb)
- {
+ if (c->skb) {
c->dptr = c->skb->data;
c->max = c->mtu;
- }
- else
- {
- c->count= 0;
+ } else {
+ c->count = 0;
c->max = 0;
}
RT_UNLOCK;
c->skb2 = dev_alloc_skb(c->mtu);
- if(c->skb2==NULL)
+ if (c->skb2 == NULL)
printk(KERN_WARNING "%s: memory squeeze.\n",
- c->netdevice->name);
+ c->netdevice->name);
else
- {
- skb_put(c->skb2,c->mtu);
- }
- c->stats.rx_packets++;
- c->stats.rx_bytes+=ct;
-
+ skb_put(c->skb2, c->mtu);
+ c->netdevice->stats.rx_packets++;
+ c->netdevice->stats.rx_bytes += ct;
}
/*
* If we received a frame we must now process it.
*/
- if(skb)
- {
+ if (skb) {
skb_trim(skb, ct);
- c->rx_function(c,skb);
- }
- else
- {
- c->stats.rx_dropped++;
+ c->rx_function(c, skb);
+ } else {
+ c->netdevice->stats.rx_dropped++;
printk(KERN_ERR "%s: Lost a frame\n", c->netdevice->name);
}
}
* Returns true if the buffer cross a DMA boundary on a PC. The poor
* thing can only DMA within a 64K block not across the edges of it.
*/
-
+
static inline int spans_boundary(struct sk_buff *skb)
{
unsigned long a=(unsigned long)skb->data;
EXPORT_SYMBOL(z8530_queue_xmit);
-/**
- * z8530_get_stats - Get network statistics
- * @c: The channel to use
- *
- * Get the statistics block. We keep the statistics in software as
- * the chip doesn't do it for us.
- *
- * Locking is ignored here - we could lock for a copy but its
- * not likely to be that big an issue
- */
-
-struct net_device_stats *z8530_get_stats(struct z8530_channel *c)
-{
- return &c->stats;
-}
-
-EXPORT_SYMBOL(z8530_get_stats);
-
/*
* Module support
*/
void *private; /* For our owner */
struct net_device *netdevice; /* Network layer device */
- struct net_device_stats stats; /* Network layer statistics */
/*
* Async features
unsigned char tx_active; /* character is being xmitted */
unsigned char tx_stopped; /* output is suspended */
- spinlock_t *lock; /* Devicr lock */
-};
+ spinlock_t *lock; /* Device lock */
+};
/*
* Each Z853x0 device.
- */
-
+ */
+
struct z8530_dev
{
char *name; /* Device instance name */
extern int z8530_sync_txdma_close(struct net_device *, struct z8530_channel *);
extern int z8530_channel_load(struct z8530_channel *, u8 *);
extern int z8530_queue_xmit(struct z8530_channel *c, struct sk_buff *skb);
-extern struct net_device_stats *z8530_get_stats(struct z8530_channel *c);
extern void z8530_null_rx(struct z8530_channel *c, struct sk_buff *skb);
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = ei_poll;
#endif
- NS8390_init(dev, 0);
+ NS8390p_init(dev, 0);
#if 1
/* Enable interrupt generation on softconfig cards -- M.U */
Trendnet TEW-424UB
ASUS P5B Deluxe
Toshiba Satellite Pro series of laptops
+ Asus Wireless Link
Thanks to Realtek for their support!
source "drivers/net/wireless/p54/Kconfig"
source "drivers/net/wireless/ath5k/Kconfig"
+source "drivers/net/wireless/ath9k/Kconfig"
source "drivers/net/wireless/iwlwifi/Kconfig"
source "drivers/net/wireless/hostap/Kconfig"
source "drivers/net/wireless/b43/Kconfig"
obj-$(CONFIG_P54_COMMON) += p54/
obj-$(CONFIG_ATH5K) += ath5k/
+obj-$(CONFIG_ATH9K) += ath9k/
obj-$(CONFIG_MAC80211_HWSIM) += mac80211_hwsim.o
#define AR5K_SREV_RAD_2111 0x20
#define AR5K_SREV_RAD_5112 0x30
#define AR5K_SREV_RAD_5112A 0x35
+#define AR5K_SREV_RAD_5112B 0x36
#define AR5K_SREV_RAD_2112 0x40
#define AR5K_SREV_RAD_2112A 0x45
-#define AR5K_SREV_RAD_SC0 0x56 /* Found on 2413/2414 */
-#define AR5K_SREV_RAD_SC1 0x63 /* Found on 5413/5414 */
-#define AR5K_SREV_RAD_SC2 0xa2 /* Found on 2424-5/5424 */
+#define AR5K_SREV_RAD_2112B 0x46
+#define AR5K_SREV_RAD_SC0 0x50 /* Found on 2413/2414 */
+#define AR5K_SREV_RAD_SC1 0x60 /* Found on 5413/5414 */
+#define AR5K_SREV_RAD_SC2 0xa0 /* Found on 2424-5/5424 */
#define AR5K_SREV_RAD_5133 0xc0 /* MIMO found on 5418 */
/* IEEE defs */
#include <linux/version.h>
#include <linux/module.h>
#include <linux/delay.h>
+#include <linux/hardirq.h>
#include <linux/if.h>
+#include <linux/io.h>
#include <linux/netdevice.h>
#include <linux/cache.h>
#include <linux/pci.h>
{ PCI_VDEVICE(ATHEROS, 0x001a), .driver_data = AR5K_AR5212 }, /* 2413 Griffin-lite */
{ PCI_VDEVICE(ATHEROS, 0x001b), .driver_data = AR5K_AR5212 }, /* 5413 Eagle */
{ PCI_VDEVICE(ATHEROS, 0x001c), .driver_data = AR5K_AR5212 }, /* 5424 Condor (PCI-E)*/
- { PCI_VDEVICE(ATHEROS, 0x0023), .driver_data = AR5K_AR5212 }, /* 5416 */
- { PCI_VDEVICE(ATHEROS, 0x0024), .driver_data = AR5K_AR5212 }, /* 5418 */
{ 0 }
};
MODULE_DEVICE_TABLE(pci, ath5k_pci_id_table);
/* Set private data */
pci_set_drvdata(pdev, hw);
- /* Enable msi for devices that support it */
- pci_enable_msi(pdev);
-
/* Setup interrupt handler */
ret = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc);
if (ret) {
err_irq:
free_irq(pdev->irq, sc);
err_free:
- pci_disable_msi(pdev);
ieee80211_free_hw(hw);
err_map:
pci_iounmap(pdev, mem);
ath5k_detach(pdev, hw);
ath5k_hw_detach(sc->ah);
free_irq(pdev->irq, sc);
- pci_disable_msi(pdev);
pci_iounmap(pdev, sc->iobase);
pci_release_region(pdev, 0);
pci_disable_device(pdev);
ath5k_led_off(sc);
ath5k_stop_hw(sc);
+
+ free_irq(pdev->irq, sc);
+ pci_disable_msi(pdev);
pci_save_state(pdev);
pci_disable_device(pdev);
pci_set_power_state(pdev, PCI_D3hot);
struct ath5k_hw *ah = sc->ah;
int i, err;
- err = pci_set_power_state(pdev, PCI_D0);
- if (err)
- return err;
+ pci_restore_state(pdev);
err = pci_enable_device(pdev);
if (err)
return err;
- pci_restore_state(pdev);
/*
* Suspend/Resume resets the PCI configuration space, so we have to
* re-disable the RETRY_TIMEOUT register (0x41) to keep
*/
pci_write_config_byte(pdev, 0x41, 0);
- ath5k_init(sc);
+ pci_enable_msi(pdev);
+
+ err = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc);
+ if (err) {
+ ATH5K_ERR(sc, "request_irq failed\n");
+ goto err_msi;
+ }
+
+ err = ath5k_init(sc);
+ if (err)
+ goto err_irq;
ath5k_led_enable(sc);
/*
ath5k_hw_reset_key(ah, i);
return 0;
+err_irq:
+ free_irq(pdev->irq, sc);
+err_msi:
+ pci_disable_msi(pdev);
+ pci_disable_device(pdev);
+ return err;
}
#endif /* CONFIG_PM */
pktlen = skb->len;
- if (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT)) {
+ if (info->control.hw_key) {
keyidx = info->control.hw_key->hw_key_idx;
pktlen += info->control.icv_len;
}
txq->link = &ds->ds_link;
ath5k_hw_tx_start(ah, txq->qnum);
+ mmiowb();
spin_unlock_bh(&txq->lock);
return 0;
ath5k_hw_stop_pcu_recv(ah); /* disable PCU */
ath5k_hw_set_rx_filter(ah, 0); /* clear recv filter */
ath5k_hw_stop_rx_dma(ah); /* disable DMA engine */
- mdelay(3); /* 3ms is long enough for 1 frame */
ath5k_debug_printrxbuffs(sc, ah);
struct ath5k_rx_status rs = {};
struct sk_buff *skb;
struct ath5k_softc *sc = (void *)data;
- struct ath5k_buf *bf;
+ struct ath5k_buf *bf, *bf_last;
struct ath5k_desc *ds;
int ret;
int hdrlen;
int pad;
spin_lock(&sc->rxbuflock);
+ if (list_empty(&sc->rxbuf)) {
+ ATH5K_WARN(sc, "empty rx buf pool\n");
+ goto unlock;
+ }
+ bf_last = list_entry(sc->rxbuf.prev, struct ath5k_buf, list);
do {
rxs.flag = 0;
- if (unlikely(list_empty(&sc->rxbuf))) {
- ATH5K_WARN(sc, "empty rx buf pool\n");
- break;
- }
bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list);
BUG_ON(bf->skb == NULL);
skb = bf->skb;
ds = bf->desc;
- /* TODO only one segment */
- pci_dma_sync_single_for_cpu(sc->pdev, sc->desc_daddr,
- sc->desc_len, PCI_DMA_FROMDEVICE);
-
- if (unlikely(ds->ds_link == bf->daddr)) /* this is the end */
- break;
+ /*
+ * last buffer must not be freed to ensure proper hardware
+ * function. When the hardware finishes also a packet next to
+ * it, we are sure, it doesn't use it anymore and we can go on.
+ */
+ if (bf_last == bf)
+ bf->flags |= 1;
+ if (bf->flags) {
+ struct ath5k_buf *bf_next = list_entry(bf->list.next,
+ struct ath5k_buf, list);
+ ret = sc->ah->ah_proc_rx_desc(sc->ah, bf_next->desc,
+ &rs);
+ if (ret)
+ break;
+ bf->flags &= ~1;
+ /* skip the overwritten one (even status is martian) */
+ goto next;
+ }
ret = sc->ah->ah_proc_rx_desc(sc->ah, ds, &rs);
if (unlikely(ret == -EINPROGRESS))
goto next;
}
accept:
- pci_dma_sync_single_for_cpu(sc->pdev, bf->skbaddr,
- rs.rs_datalen, PCI_DMA_FROMDEVICE);
pci_unmap_single(sc->pdev, bf->skbaddr, sc->rxbufsize,
PCI_DMA_FROMDEVICE);
bf->skb = NULL;
next:
list_move_tail(&bf->list, &sc->rxbuf);
} while (ath5k_rxbuf_setup(sc, bf) == 0);
+unlock:
spin_unlock(&sc->rxbuflock);
}
list_for_each_entry_safe(bf, bf0, &txq->q, list) {
ds = bf->desc;
- /* TODO only one segment */
- pci_dma_sync_single_for_cpu(sc->pdev, sc->desc_daddr,
- sc->desc_len, PCI_DMA_FROMDEVICE);
ret = sc->ah->ah_proc_tx_desc(sc->ah, ds, &ts);
if (unlikely(ret == -EINPROGRESS))
break;
ATH5K_WARN(sc, "beacon queue %u didn't stop?\n", sc->bhalq);
/* NB: hw still stops DMA, so proceed */
}
- pci_dma_sync_single_for_cpu(sc->pdev, bf->skbaddr, bf->skb->len,
- PCI_DMA_TODEVICE);
ath5k_hw_put_tx_buf(ah, sc->bhalq, bf->daddr);
ath5k_hw_tx_start(ah, sc->bhalq);
ath5k_hw_set_intr(ah, 0);
sc->bmisscount = 0;
+ sc->imask &= ~(AR5K_INT_BMISS | AR5K_INT_SWBA);
if (sc->opmode == IEEE80211_IF_TYPE_STA) {
sc->imask |= AR5K_INT_BMISS;
ret = 0;
done:
+ mmiowb();
mutex_unlock(&sc->lock);
return ret;
}
if (!test_bit(ATH_STAT_INVALID, sc->status)) {
ath5k_led_off(sc);
ath5k_hw_set_intr(ah, 0);
+ synchronize_irq(sc->pdev->irq);
}
ath5k_txq_cleanup(sc);
if (!test_bit(ATH_STAT_INVALID, sc->status)) {
}
}
ath5k_txbuf_free(sc, sc->bbuf);
+ mmiowb();
mutex_unlock(&sc->lock);
del_timer_sync(&sc->calib_tim);
+ tasklet_kill(&sc->rxtq);
+ tasklet_kill(&sc->txtq);
+ tasklet_kill(&sc->restq);
return ret;
}
struct pci_dev *pdev = sc->pdev;
char name[ATH5K_LED_MAX_NAME_LEN + 1];
- sc->led_on = 0; /* active low */
-
/*
* Auto-enable soft led processing for IBM cards and for
* 5211 minipci cards.
pdev->device == PCI_DEVICE_ID_ATHEROS_AR5211) {
__set_bit(ATH_STAT_LEDSOFT, sc->status);
sc->led_pin = 0;
+ sc->led_on = 0; /* active low */
}
/* Enable softled on PIN1 on HP Compaq nc6xx, nc4000 & nx5000 laptops */
if (pdev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ) {
__set_bit(ATH_STAT_LEDSOFT, sc->status);
sc->led_pin = 1;
+ sc->led_on = 1; /* active high */
}
if (!test_bit(ATH_STAT_LEDSOFT, sc->status))
goto out;
/* XXX: assoc id is set to 0 for now, mac80211 doesn't have
* a clean way of letting us retrieve this yet. */
ath5k_hw_set_associd(ah, ah->ah_bssid, 0);
+ mmiowb();
}
if (conf->changed & IEEE80211_IFCC_BEACON &&
}
unlock:
+ mmiowb();
mutex_unlock(&sc->lock);
return ret;
}
ath5k_debug_dump_skb(sc, skb, "BC ", 1);
- mutex_lock(&sc->lock);
-
if (sc->opmode != IEEE80211_IF_TYPE_IBSS) {
ret = -EIO;
goto end;
ret = ath5k_beacon_setup(sc, sc->bbuf);
if (ret)
sc->bbuf->skb = NULL;
- else
+ else {
ath5k_beacon_config(sc);
+ mmiowb();
+ }
end:
- mutex_unlock(&sc->lock);
return ret;
}
struct ath5k_buf {
struct list_head list;
- unsigned int flags; /* tx descriptor flags */
+ unsigned int flags; /* rx descriptor flags */
struct ath5k_desc *desc; /* virtual addr of desc */
dma_addr_t daddr; /* physical addr of desc */
struct sk_buff *skb; /* skbuff for buf */
REG_STRUCT_INIT(AR5K_CPC1),
REG_STRUCT_INIT(AR5K_CPC2),
REG_STRUCT_INIT(AR5K_CPC3),
- REG_STRUCT_INIT(AR5K_CPCORN),
+ REG_STRUCT_INIT(AR5K_CPCOVF),
REG_STRUCT_INIT(AR5K_RESET_CTL),
REG_STRUCT_INIT(AR5K_SLEEP_CTL),
REG_STRUCT_INIT(AR5K_INTPEND),
struct ath5k_softc;
struct ath5k_hw;
-struct ieee80211_hw_mode;
struct sk_buff;
struct ath5k_buf;
for (c = 0; c < 2; c++) {
cur_reg = regs[c];
+
+ /* Save previous value */
init_val = ath5k_hw_reg_read(ah, cur_reg);
for (i = 0; i < 256; i++) {
var_pattern = 0x003b080f;
ath5k_hw_reg_write(ah, var_pattern, cur_reg);
}
+
+ /* Restore previous value */
+ ath5k_hw_reg_write(ah, init_val, cur_reg);
+
}
return 0;
/* Identify the radio chip*/
if (ah->ah_version == AR5K_AR5210) {
ah->ah_radio = AR5K_RF5110;
+ /*
+ * Register returns 0x0/0x04 for radio revision
+ * so ath5k_hw_radio_revision doesn't parse the value
+ * correctly. For now we are based on mac's srev to
+ * identify RF2425 radio.
+ */
+ } else if (srev == AR5K_SREV_VER_AR2425) {
+ ah->ah_radio = AR5K_RF2425;
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2425;
} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112) {
ah->ah_radio = AR5K_RF5111;
ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5111;
} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC0) {
-
ah->ah_radio = AR5K_RF5112;
-
- if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) {
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
- } else {
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
- }
-
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC1) {
ah->ah_radio = AR5K_RF2413;
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413;
} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC2) {
ah->ah_radio = AR5K_RF5413;
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413;
} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5133) {
-
/* AR5424 */
if (srev >= AR5K_SREV_VER_AR5424) {
ah->ah_radio = AR5K_RF5413;
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5424;
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413;
/* AR2424 */
} else {
ah->ah_radio = AR5K_RF2413; /* For testing */
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+ ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413;
}
-
- /*
- * Register returns 0x4 for radio revision
- * so ath5k_hw_radio_revision doesn't parse the value
- * correctly. For now we are based on mac's srev to
- * identify RF2425 radio.
- */
- } else if (srev == AR5K_SREV_VER_AR2425) {
- ah->ah_radio = AR5K_RF2425;
- ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
}
-
ah->ah_phy = AR5K_PHY(0);
/*
- * Identify AR5212-based PCI-E cards
- * And write some initial settings.
- *
- * (doing a "strings" on ndis driver
- * -ar5211.sys- reveals the following
- * pci-e related functions:
- *
- * pcieClockReq
- * pcieRxErrNotify
- * pcieL1SKPEnable
- * pcieAspm
- * pcieDisableAspmOnRfWake
- * pciePowerSaveEnable
- *
- * I guess these point to ClockReq but
- * i'm not sure.)
+ * Write PCI-E power save settings
*/
if ((ah->ah_version == AR5K_AR5212) && (pdev->is_pcie)) {
ath5k_hw_reg_write(ah, 0x9248fc00, 0x4080);
if (ret)
goto err_free;
+ /* Write AR5K_PCICFG_UNK on 2112B and later chips */
+ if (ah->ah_radio_5ghz_revision > AR5K_SREV_RAD_2112B ||
+ srev > AR5K_SREV_VER_AR2413) {
+ ath5k_hw_reg_write(ah, AR5K_PCICFG_UNK, AR5K_PCICFG);
+ }
+
/*
* Get card capabilities, values, ...
*/
-
ret = ath5k_eeprom_init(ah);
if (ret) {
ATH5K_ERR(sc, "unable to init EEPROM\n");
* Write some more initial register settings
*/
if (ah->ah_version == AR5K_AR5212) {
- ath5k_hw_reg_write(ah, 0x0002a002, AR5K_PHY(11));
+ ath5k_hw_reg_write(ah, 0x0002a002, 0x982c);
if (channel->hw_value == CHANNEL_G)
if (ah->ah_mac_srev < AR5K_SREV_VER_AR2413)
ath5k_hw_reg_write(ah, 0x00f80d80,
- AR5K_PHY(83));
+ 0x994c);
else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2424)
ath5k_hw_reg_write(ah, 0x00380140,
- AR5K_PHY(83));
+ 0x994c);
else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2425)
ath5k_hw_reg_write(ah, 0x00fc0ec0,
- AR5K_PHY(83));
+ 0x994c);
else /* 2425 */
ath5k_hw_reg_write(ah, 0x00fc0fc0,
- AR5K_PHY(83));
+ 0x994c);
else
- ath5k_hw_reg_write(ah, 0x00000000,
- AR5K_PHY(83));
-
- ath5k_hw_reg_write(ah, 0x000009b5, 0xa228);
- ath5k_hw_reg_write(ah, 0x0000000f, 0x8060);
+ ath5k_hw_reg_write(ah, 0x00000000, 0x994c);
+
+ /* Some bits are disabled here, we know nothing about
+ * register 0xa228 yet, most of the times this ends up
+ * with a value 0x9b5 -haven't seen any dump with
+ * a different value- */
+ /* Got this from decompiling binary HAL */
+ data = ath5k_hw_reg_read(ah, 0xa228);
+ data &= 0xfffffdff;
+ ath5k_hw_reg_write(ah, data, 0xa228);
+
+ data = ath5k_hw_reg_read(ah, 0xa228);
+ data &= 0xfffe03ff;
+ ath5k_hw_reg_write(ah, data, 0xa228);
+ data = 0;
+
+ /* Just write 0x9b5 ? */
+ /* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */
+ ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK);
ath5k_hw_reg_write(ah, 0x00000000, 0xa254);
ath5k_hw_reg_write(ah, 0x0000000e, AR5K_PHY_SCAL);
}
else
data = 0xffb80d20;
ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL);
+ data = 0;
}
/*
/*
* Write RF registers
- * TODO:Does this work on 5211 (5111) ?
*/
ret = ath5k_hw_rfregs(ah, channel, mode);
if (ret)
return ret;
/* Set antenna mode */
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x44),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_ANT_CTL,
ah->ah_antenna[ee_mode][0], 0xfffffc06);
/*
ath5k_hw_reg_write(ah,
AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]),
- AR5K_PHY(0x5a));
+ AR5K_PHY_NFTHRES);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x11),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_SETTLING,
(ee->ee_switch_settling[ee_mode] << 7) & 0x3f80,
0xffffc07f);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x12),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_GAIN,
(ee->ee_ant_tx_rx[ee_mode] << 12) & 0x3f000,
0xfffc0fff);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x14),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_DESIRED_SIZE,
(ee->ee_adc_desired_size[ee_mode] & 0x00ff) |
((ee->ee_pga_desired_size[ee_mode] << 8) & 0xff00),
0xffff0000);
(ee->ee_tx_end2xpa_disable[ee_mode] << 24) |
(ee->ee_tx_end2xpa_disable[ee_mode] << 16) |
(ee->ee_tx_frm2xpa_enable[ee_mode] << 8) |
- (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY(0x0d));
+ (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x0a),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_RF_CTL3,
ee->ee_tx_end2xlna_enable[ee_mode] << 8, 0xffff00ff);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x19),
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_NF,
(ee->ee_thr_62[ee_mode] << 12) & 0x7f000, 0xfff80fff);
- AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x49), 4, 0xffffff01);
+ AR5K_REG_MASKED_BITS(ah, AR5K_PHY_OFDM_SELFCORR, 4, 0xffffff01);
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
AR5K_PHY_IQ_CORR_ENABLE |
ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
/*
- * 5111/5112 Specific
+ * On 5211+ read activation -> rx delay
+ * and use it.
*/
if (ah->ah_version != AR5K_AR5210) {
data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
data = (channel->hw_value & CHANNEL_CCK) ?
((data << 2) / 22) : (data / 10);
- udelay(100 + data);
+ udelay(100 + (2 * data));
+ data = 0;
} else {
mdelay(1);
}
/*
- * Enable calibration and wait until completion
+ * Perform ADC test (?)
+ */
+ data = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
+ ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
+ for (i = 0; i <= 20; i++) {
+ if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
+ break;
+ udelay(200);
+ }
+ ath5k_hw_reg_write(ah, data, AR5K_PHY_TST1);
+ data = 0;
+
+ /*
+ * Start automatic gain calibration
+ *
+ * During AGC calibration RX path is re-routed to
+ * a signal detector so we don't receive anything.
+ *
+ * This method is used to calibrate some static offsets
+ * used together with on-the fly I/Q calibration (the
+ * one performed via ath5k_hw_phy_calibrate), that doesn't
+ * interrupt rx path.
+ *
+ * If we are in a noisy environment AGC calibration may time
+ * out.
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_CAL);
+ /* At the same time start I/Q calibration for QAM constellation
+ * -no need for CCK- */
+ ah->ah_calibration = false;
+ if (!(mode == AR5K_MODE_11B)) {
+ ah->ah_calibration = true;
+ AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
+ AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
+ AR5K_PHY_IQ_RUN);
+ }
+
+ /* Wait for gain calibration to finish (we check for I/Q calibration
+ * during ath5k_phy_calibrate) */
if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_CAL, 0, false)) {
- ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n",
+ ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n",
channel->center_freq);
return -EAGAIN;
}
+ /*
+ * Start noise floor calibration
+ *
+ * If we run NF calibration before AGC, it always times out.
+ * Binary HAL starts NF and AGC calibration at the same time
+ * and only waits for AGC to finish. I believe that's wrong because
+ * during NF calibration, rx path is also routed to a detector, so if
+ * it doesn't finish we won't have RX.
+ *
+ * XXX: Find an interval that's OK for all cards...
+ */
ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
if (ret)
return ret;
- ah->ah_calibration = false;
-
- /* A and G modes can use QAM modulation which requires enabling
- * I and Q calibration. Don't bother in B mode. */
- if (!(mode == AR5K_MODE_11B)) {
- ah->ah_calibration = true;
- AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
- AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
- AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
- AR5K_PHY_IQ_RUN);
- }
-
/*
* Reset queues and start beacon timers at the end of the reset routine
*/
ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK);
ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY);
ath5k_hw_reg_write(ah, ah->ah_phy_spending, AR5K_PHY_SPENDING);
+
+ data = ath5k_hw_reg_read(ah, AR5K_USEC_5211) & 0xffffc07f ;
+ data |= (ah->ah_phy_spending == AR5K_PHY_SPENDING_18) ?
+ 0x00000f80 : 0x00001380 ;
+ ath5k_hw_reg_write(ah, data, AR5K_USEC_5211);
+ data = 0;
}
if (ah->ah_version == AR5K_AR5212) {
bool set_chip, u16 sleep_duration)
{
unsigned int i;
- u32 staid;
+ u32 staid, data;
ATH5K_TRACE(ah->ah_sc);
staid = ath5k_hw_reg_read(ah, AR5K_STA_ID1);
case AR5K_PM_NETWORK_SLEEP:
if (set_chip)
ath5k_hw_reg_write(ah,
- AR5K_SLEEP_CTL_SLE | sleep_duration,
+ AR5K_SLEEP_CTL_SLE_ALLOW |
+ sleep_duration,
AR5K_SLEEP_CTL);
staid |= AR5K_STA_ID1_PWR_SV;
break;
case AR5K_PM_AWAKE:
+
+ staid &= ~AR5K_STA_ID1_PWR_SV;
+
if (!set_chip)
goto commit;
- ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE,
- AR5K_SLEEP_CTL);
+ /* Preserve sleep duration */
+ data = ath5k_hw_reg_read(ah, AR5K_SLEEP_CTL);
+ if( data & 0xffc00000 ){
+ data = 0;
+ } else {
+ data = data & 0xfffcffff;
+ }
- for (i = 5000; i > 0; i--) {
+ ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
+ udelay(15);
+
+ for (i = 50; i > 0; i--) {
/* Check if the chip did wake up */
if ((ath5k_hw_reg_read(ah, AR5K_PCICFG) &
AR5K_PCICFG_SPWR_DN) == 0)
/* Wait a bit and retry */
udelay(200);
- ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE,
- AR5K_SLEEP_CTL);
+ ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
}
/* Fail if the chip didn't wake up */
if (i <= 0)
return -EIO;
- staid &= ~AR5K_STA_ID1_PWR_SV;
break;
default:
{
ATH5K_TRACE(ah->ah_sc);
ath5k_hw_reg_write(ah, AR5K_CR_RXE, AR5K_CR);
+ ath5k_hw_reg_read(ah, AR5K_CR);
}
/*
}
/* Start queue */
ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+ ath5k_hw_reg_read(ah, AR5K_CR);
} else {
/* Return if queue is disabled */
if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXD, queue))
/* Stop queue */
ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+ ath5k_hw_reg_read(ah, AR5K_CR);
} else {
/*
* Schedule TX disable and wait until queue is empty
/* Clear register */
ath5k_hw_reg_write(ah, 0, AR5K_QCU_TXD);
+ if (pending)
+ return -EBUSY;
}
/* TODO: Check for success else return error */
* (they will be re-enabled afterwards).
*/
ath5k_hw_reg_write(ah, AR5K_IER_DISABLE, AR5K_IER);
+ ath5k_hw_reg_read(ah, AR5K_IER);
old_mask = ah->ah_imr;
/* ..re-enable interrupts */
ath5k_hw_reg_write(ah, AR5K_IER_ENABLE, AR5K_IER);
+ ath5k_hw_reg_read(ah, AR5K_IER);
return old_mask;
}
ath5k_hw_reg_write(ah, ah->ah_turbo ?
AR5K_INIT_PROTO_TIME_CNTRL_TURBO :
AR5K_INIT_PROTO_TIME_CNTRL, AR5K_IFS1);
- /* Set PHY register 0x9844 (??) */
+ /* Set AR5K_PHY_SETTLING */
ath5k_hw_reg_write(ah, ah->ah_turbo ?
- (ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x38 :
- (ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x1C,
- AR5K_PHY(17));
+ (ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F)
+ | 0x38 :
+ (ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F)
+ | 0x1C,
+ AR5K_PHY_SETTLING);
/* Set Frame Control Register */
ath5k_hw_reg_write(ah, ah->ah_turbo ?
(AR5K_PHY_FRAME_CTL_INI | AR5K_PHY_TURBO_MODE |
if (tq->tqi_flags & AR5K_TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE)
AR5K_REG_ENABLE_BITS(ah,
AR5K_QUEUE_MISC(queue),
- AR5K_QCU_MISC_TXE);
+ AR5K_QCU_MISC_RDY_VEOL_POLICY);
}
if (tq->tqi_flags & AR5K_TXQ_FLAG_BACKOFF_DISABLE)
{ AR5K_QUEUE_TXDP(9), 0x00000000 },
{ AR5K_DCU_FP, 0x00000000 },
{ AR5K_DCU_TXP, 0x00000000 },
- { AR5K_DCU_TX_FILTER, 0x00000000 },
+ { AR5K_DCU_TX_FILTER_0_BASE, 0x00000000 },
/* Unknown table */
{ 0x1078, 0x00000000 },
{ 0x10b8, 0x00000000 },
{ AR5K_PHY(645), 0x00106c10 },
{ AR5K_PHY(646), 0x009c4060 },
{ AR5K_PHY(647), 0x1483800a },
- /* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413 */
+ /* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413/2425 */
{ AR5K_PHY(648), 0x01831061 },
{ AR5K_PHY(649), 0x00000400 },
/*{ AR5K_PHY(650), 0x000001b5 },*/
{ AR5K_RF_GAIN(63), { 0x000000f9 } },
};
+/* Initial RF Gain settings for RF2425 */
+static const struct ath5k_ini_rfgain rfgain_2425[] = {
+ { AR5K_RF_GAIN(0), { 0x00000000 } },
+ { AR5K_RF_GAIN(1), { 0x00000040 } },
+ { AR5K_RF_GAIN(2), { 0x00000080 } },
+ { AR5K_RF_GAIN(3), { 0x00000181 } },
+ { AR5K_RF_GAIN(4), { 0x000001c1 } },
+ { AR5K_RF_GAIN(5), { 0x00000001 } },
+ { AR5K_RF_GAIN(6), { 0x00000041 } },
+ { AR5K_RF_GAIN(7), { 0x00000081 } },
+ { AR5K_RF_GAIN(8), { 0x00000188 } },
+ { AR5K_RF_GAIN(9), { 0x000001c8 } },
+ { AR5K_RF_GAIN(10), { 0x00000008 } },
+ { AR5K_RF_GAIN(11), { 0x00000048 } },
+ { AR5K_RF_GAIN(12), { 0x00000088 } },
+ { AR5K_RF_GAIN(13), { 0x00000189 } },
+ { AR5K_RF_GAIN(14), { 0x000001c9 } },
+ { AR5K_RF_GAIN(15), { 0x00000009 } },
+ { AR5K_RF_GAIN(16), { 0x00000049 } },
+ { AR5K_RF_GAIN(17), { 0x00000089 } },
+ { AR5K_RF_GAIN(18), { 0x000001b0 } },
+ { AR5K_RF_GAIN(19), { 0x000001f0 } },
+ { AR5K_RF_GAIN(20), { 0x00000030 } },
+ { AR5K_RF_GAIN(21), { 0x00000070 } },
+ { AR5K_RF_GAIN(22), { 0x00000171 } },
+ { AR5K_RF_GAIN(23), { 0x000001b1 } },
+ { AR5K_RF_GAIN(24), { 0x000001f1 } },
+ { AR5K_RF_GAIN(25), { 0x00000031 } },
+ { AR5K_RF_GAIN(26), { 0x00000071 } },
+ { AR5K_RF_GAIN(27), { 0x000001b8 } },
+ { AR5K_RF_GAIN(28), { 0x000001f8 } },
+ { AR5K_RF_GAIN(29), { 0x00000038 } },
+ { AR5K_RF_GAIN(30), { 0x00000078 } },
+ { AR5K_RF_GAIN(31), { 0x000000b8 } },
+ { AR5K_RF_GAIN(32), { 0x000001b9 } },
+ { AR5K_RF_GAIN(33), { 0x000001f9 } },
+ { AR5K_RF_GAIN(34), { 0x00000039 } },
+ { AR5K_RF_GAIN(35), { 0x00000079 } },
+ { AR5K_RF_GAIN(36), { 0x000000b9 } },
+ { AR5K_RF_GAIN(37), { 0x000000f9 } },
+ { AR5K_RF_GAIN(38), { 0x000000f9 } },
+ { AR5K_RF_GAIN(39), { 0x000000f9 } },
+ { AR5K_RF_GAIN(40), { 0x000000f9 } },
+ { AR5K_RF_GAIN(41), { 0x000000f9 } },
+ { AR5K_RF_GAIN(42), { 0x000000f9 } },
+ { AR5K_RF_GAIN(43), { 0x000000f9 } },
+ { AR5K_RF_GAIN(44), { 0x000000f9 } },
+ { AR5K_RF_GAIN(45), { 0x000000f9 } },
+ { AR5K_RF_GAIN(46), { 0x000000f9 } },
+ { AR5K_RF_GAIN(47), { 0x000000f9 } },
+ { AR5K_RF_GAIN(48), { 0x000000f9 } },
+ { AR5K_RF_GAIN(49), { 0x000000f9 } },
+ { AR5K_RF_GAIN(50), { 0x000000f9 } },
+ { AR5K_RF_GAIN(51), { 0x000000f9 } },
+ { AR5K_RF_GAIN(52), { 0x000000f9 } },
+ { AR5K_RF_GAIN(53), { 0x000000f9 } },
+ { AR5K_RF_GAIN(54), { 0x000000f9 } },
+ { AR5K_RF_GAIN(55), { 0x000000f9 } },
+ { AR5K_RF_GAIN(56), { 0x000000f9 } },
+ { AR5K_RF_GAIN(57), { 0x000000f9 } },
+ { AR5K_RF_GAIN(58), { 0x000000f9 } },
+ { AR5K_RF_GAIN(59), { 0x000000f9 } },
+ { AR5K_RF_GAIN(60), { 0x000000f9 } },
+ { AR5K_RF_GAIN(61), { 0x000000f9 } },
+ { AR5K_RF_GAIN(62), { 0x000000f9 } },
+ { AR5K_RF_GAIN(63), { 0x000000f9 } },
+};
+
static const struct ath5k_gain_opt rfgain_opt_5112 = {
1,
8,
freq = 0; /* only 2Ghz */
break;
case AR5K_RF2425:
- ath5k_rfg = rfgain_2413;
- size = ARRAY_SIZE(rfgain_2413);
+ ath5k_rfg = rfgain_2425;
+ size = ARRAY_SIZE(rfgain_2425);
freq = 0; /* only 2Ghz */
break;
default:
data = data0 = data1 = data2 = 0;
c = channel->center_freq;
- /*
- * Set the channel on the RF5112 or newer
- */
if (c < 4800) {
if (!((c - 2224) % 5)) {
data0 = ((2 * (c - 704)) - 3040) / 10;
return -EINVAL;
data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8);
- } else {
+ } else if ((c - (c % 5)) != 2 || c > 5435) {
if (!(c % 20) && c >= 5120) {
data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
data2 = ath5k_hw_bitswap(3, 2);
data2 = ath5k_hw_bitswap(1, 2);
} else
return -EINVAL;
+ } else {
+ data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
+ data2 = ath5k_hw_bitswap(0, 2);
}
data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001;
return 0;
}
+/*
+ * Set the channel on the RF2425
+ */
+static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah,
+ struct ieee80211_channel *channel)
+{
+ u32 data, data0, data2;
+ u16 c;
+
+ data = data0 = data2 = 0;
+ c = channel->center_freq;
+
+ if (c < 4800) {
+ data0 = ath5k_hw_bitswap((c - 2272), 8);
+ data2 = 0;
+ /* ? 5GHz ? */
+ } else if ((c - (c % 5)) != 2 || c > 5435) {
+ if (!(c % 20) && c < 5120)
+ data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
+ else if (!(c % 10))
+ data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8);
+ else if (!(c % 5))
+ data0 = ath5k_hw_bitswap((c - 4800) / 5, 8);
+ else
+ return -EINVAL;
+ data2 = ath5k_hw_bitswap(1, 2);
+ } else {
+ data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
+ data2 = ath5k_hw_bitswap(0, 2);
+ }
+
+ data = (data0 << 4) | data2 << 2 | 0x1001;
+
+ ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER);
+ ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5);
+
+ return 0;
+}
+
/*
* Set a channel on the radio chip
*/
case AR5K_RF5111:
ret = ath5k_hw_rf5111_channel(ah, channel);
break;
+ case AR5K_RF2425:
+ ret = ath5k_hw_rf2425_channel(ah, channel);
+ break;
default:
ret = ath5k_hw_rf5112_channel(ah, channel);
break;
if (ret)
return ret;
+ /* Set JAPAN setting for channel 14 */
+ if (channel->center_freq == 2484) {
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
+ AR5K_PHY_CCKTXCTL_JAPAN);
+ } else {
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
+ AR5K_PHY_CCKTXCTL_WORLD);
+ }
+
ah->ah_current_channel.center_freq = channel->center_freq;
ah->ah_current_channel.hw_value = channel->hw_value;
ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false;
* http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \
* &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7
*
+ * XXX: Since during noise floor calibration antennas are detached according to
+ * the patent, we should stop tx queues here.
*/
int
ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
s32 noise_floor;
/*
- * Enable noise floor calibration and wait until completion
+ * Enable noise floor calibration
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_NF);
if (ret) {
ATH5K_ERR(ah->ah_sc,
"noise floor calibration timeout (%uMHz)\n", freq);
- return ret;
+ return -EAGAIN;
}
/* Wait until the noise floor is calibrated and read the value */
if (noise_floor > AR5K_TUNE_NOISE_FLOOR) {
ATH5K_ERR(ah->ah_sc,
"noise floor calibration failed (%uMHz)\n", freq);
- return -EIO;
+ return -EAGAIN;
}
ah->ah_noise_floor = noise_floor;
}
/*
- * Perform a PHY calibration on RF5111/5112
+ * Perform a PHY calibration on RF5111/5112 and newer chips
*/
static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah,
struct ieee80211_channel *channel)
{
u32 i_pwr, q_pwr;
s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd;
+ int i;
ATH5K_TRACE(ah->ah_sc);
if (!ah->ah_calibration ||
- ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
+ ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
goto done;
- ah->ah_calibration = false;
+ /* Calibration has finished, get the results and re-run */
+ for (i = 0; i <= 10; i++) {
+ iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
+ i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
+ q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
+ }
- iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
- i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
- q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7;
- q_coffd = q_pwr >> 6;
+ q_coffd = q_pwr >> 7;
+ /* No correction */
if (i_coffd == 0 || q_coffd == 0)
goto done;
i_coff = ((-iq_corr) / i_coffd) & 0x3f;
- q_coff = (((s32)i_pwr / q_coffd) - 64) & 0x1f;
- /* Commit new IQ value */
+ /* Boundary check */
+ if (i_coff > 31)
+ i_coff = 31;
+ if (i_coff < -32)
+ i_coff = -32;
+
+ q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f;
+
+ /* Boundary check */
+ if (q_coff > 15)
+ q_coff = 15;
+ if (q_coff < -16)
+ q_coff = -16;
+
+ /* Commit new I/Q value */
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE |
((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S));
+ /* Re-enable calibration -if we don't we'll commit
+ * the same values again and again */
+ AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
+ AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
+ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN);
+
done:
+
+ /* TODO: Separate noise floor calibration from I/Q calibration
+ * since noise floor calibration interrupts rx path while I/Q
+ * calibration doesn't. We don't need to run noise floor calibration
+ * as often as I/Q calibration.*/
ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
/* Request RF gain */
#define AR5K_CR_TXD0 0x00000008 /* TX Disable for queue 0 on 5210 */
#define AR5K_CR_TXD1 0x00000010 /* TX Disable for queue 1 on 5210 */
#define AR5K_CR_RXD 0x00000020 /* RX Disable */
-#define AR5K_CR_SWI 0x00000040
+#define AR5K_CR_SWI 0x00000040 /* Software Interrupt */
/*
* RX Descriptor Pointer register
*/
#define AR5K_CFG 0x0014 /* Register Address */
#define AR5K_CFG_SWTD 0x00000001 /* Byte-swap TX descriptor (for big endian archs) */
-#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer (?) */
+#define AR5K_CFG_SWTB 0x00000002 /* Byte-swap TX buffer */
#define AR5K_CFG_SWRD 0x00000004 /* Byte-swap RX descriptor */
-#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer (?) */
-#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register values (?) */
-#define AR5K_CFG_ADHOC 0x00000020 /* [5211+] */
+#define AR5K_CFG_SWRB 0x00000008 /* Byte-swap RX buffer */
+#define AR5K_CFG_SWRG 0x00000010 /* Byte-swap Register access */
+#define AR5K_CFG_ADHOC 0x00000020 /* AP/Adhoc indication [5211+] */
#define AR5K_CFG_PHY_OK 0x00000100 /* [5211+] */
#define AR5K_CFG_EEBS 0x00000200 /* EEPROM is busy */
-#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (?) */
+#define AR5K_CFG_CLKGD 0x00000400 /* Clock gated (Disable dynamic clock) */
#define AR5K_CFG_TXCNT 0x00007800 /* Tx frame count (?) [5210] */
#define AR5K_CFG_TXCNT_S 11
#define AR5K_CFG_TXFSTAT 0x00008000 /* Tx frame status (?) [5210] */
#define AR5K_CFG_TXFSTRT 0x00010000 /* [5210] */
-#define AR5K_CFG_PCI_THRES 0x00060000 /* [5211+] */
+#define AR5K_CFG_PCI_THRES 0x00060000 /* PCI Master req q threshold [5211+] */
#define AR5K_CFG_PCI_THRES_S 17
/*
/*
* Transmit configuration register
*/
-#define AR5K_TXCFG 0x0030 /* Register Address */
-#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size */
-#define AR5K_TXCFG_SDMAMR_S 0
-#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */
-#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */
-#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */
-#define AR5K_TXCFG_TXFULL_S 4
-#define AR5K_TXCFG_TXFULL_0B 0x00000000
-#define AR5K_TXCFG_TXFULL_64B 0x00000010
-#define AR5K_TXCFG_TXFULL_128B 0x00000020
-#define AR5K_TXCFG_TXFULL_192B 0x00000030
-#define AR5K_TXCFG_TXFULL_256B 0x00000040
-#define AR5K_TXCFG_TXCONT_EN 0x00000080
-#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */
-#define AR5K_TXCFG_JUMBO_TXE 0x00000400 /* Enable jumbo frames transmition (?) [5211+] */
-#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */
-#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */
-#define AR5K_TXCFG_RDY_DIS 0x00004000 /* [5211+] */
+#define AR5K_TXCFG 0x0030 /* Register Address */
+#define AR5K_TXCFG_SDMAMR 0x00000007 /* DMA size (read) */
+#define AR5K_TXCFG_SDMAMR_S 0
+#define AR5K_TXCFG_B_MODE 0x00000008 /* Set b mode for 5111 (enable 2111) */
+#define AR5K_TXCFG_TXFSTP 0x00000008 /* TX DMA full Stop [5210] */
+#define AR5K_TXCFG_TXFULL 0x000003f0 /* TX Triger level mask */
+#define AR5K_TXCFG_TXFULL_S 4
+#define AR5K_TXCFG_TXFULL_0B 0x00000000
+#define AR5K_TXCFG_TXFULL_64B 0x00000010
+#define AR5K_TXCFG_TXFULL_128B 0x00000020
+#define AR5K_TXCFG_TXFULL_192B 0x00000030
+#define AR5K_TXCFG_TXFULL_256B 0x00000040
+#define AR5K_TXCFG_TXCONT_EN 0x00000080
+#define AR5K_TXCFG_DMASIZE 0x00000100 /* Flag for passing DMA size [5210] */
+#define AR5K_TXCFG_JUMBO_DESC_EN 0x00000400 /* Enable jumbo tx descriptors [5211+] */
+#define AR5K_TXCFG_ADHOC_BCN_ATIM 0x00000800 /* Adhoc Beacon ATIM Policy */
+#define AR5K_TXCFG_ATIM_WINDOW_DEF_DIS 0x00001000 /* Disable ATIM window defer [5211+] */
+#define AR5K_TXCFG_RTSRND 0x00001000 /* [5211+] */
+#define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */
+#define AR5K_TXCFG_RDY_CBR_DIS 0x00004000 /* Ready time CBR disable [5211+] */
+#define AR5K_TXCFG_JUMBO_FRM_MODE 0x00008000 /* Jumbo frame mode [5211+] */
+#define AR5K_TXCFG_DCU_CACHING_DIS 0x00010000 /* Disable DCU caching */
/*
* Receive configuration register
*/
#define AR5K_RXCFG 0x0034 /* Register Address */
-#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size */
+#define AR5K_RXCFG_SDMAMW 0x00000007 /* DMA size (write) */
#define AR5K_RXCFG_SDMAMW_S 0
-#define AR5K_RXCFG_DEF_ANTENNA 0x00000008 /* Default antenna */
-#define AR5K_RXCFG_ZLFDMA 0x00000010 /* Zero-length DMA */
-#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo frames reception (?) [5211+] */
-#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames (?) [5211+] */
+#define AR5K_RXCFG_ZLFDMA 0x00000008 /* Enable Zero-length frame DMA */
+#define AR5K_RXCFG_DEF_ANTENNA 0x00000010 /* Default antenna (?) */
+#define AR5K_RXCFG_JUMBO_RXE 0x00000020 /* Enable jumbo rx descriptors [5211+] */
+#define AR5K_RXCFG_JUMBO_WRAP 0x00000040 /* Wrap jumbo frames [5211+] */
+#define AR5K_RXCFG_SLE_ENTRY 0x00000080 /* Sleep entry policy */
/*
* Receive jumbo descriptor last address register
* MIB control register
*/
#define AR5K_MIBC 0x0040 /* Register Address */
-#define AR5K_MIBC_COW 0x00000001
-#define AR5K_MIBC_FMC 0x00000002 /* Freeze Mib Counters (?) */
-#define AR5K_MIBC_CMC 0x00000004 /* Clean Mib Counters (?) */
-#define AR5K_MIBC_MCS 0x00000008
+#define AR5K_MIBC_COW 0x00000001 /* Warn test indicator */
+#define AR5K_MIBC_FMC 0x00000002 /* Freeze MIB Counters */
+#define AR5K_MIBC_CMC 0x00000004 /* Clean MIB Counters */
+#define AR5K_MIBC_MCS 0x00000008 /* MIB counter strobe */
/*
* Timeout prescale register
*/
#define AR5K_TOPS 0x0044
-#define AR5K_TOPS_M 0x0000ffff /* [5211+] (?) */
+#define AR5K_TOPS_M 0x0000ffff
/*
* Receive timeout register (no frame received)
*/
#define AR5K_RXNOFRM 0x0048
-#define AR5K_RXNOFRM_M 0x000003ff /* [5211+] (?) */
+#define AR5K_RXNOFRM_M 0x000003ff
/*
* Transmit timeout register (no frame sent)
*/
#define AR5K_TXNOFRM 0x004c
-#define AR5K_TXNOFRM_M 0x000003ff /* [5211+] (?) */
-#define AR5K_TXNOFRM_QCU 0x000ffc00 /* [5211+] (?) */
+#define AR5K_TXNOFRM_M 0x000003ff
+#define AR5K_TXNOFRM_QCU 0x000ffc00
/*
* Receive frame gap timeout register
*/
#define AR5K_RPGTO 0x0050
-#define AR5K_RPGTO_M 0x000003ff /* [5211+] (?) */
+#define AR5K_RPGTO_M 0x000003ff
/*
* Receive frame count limit register
/*
* Misc settings register
+ * (reserved0-3)
*/
#define AR5K_MISC 0x0058 /* Register Address */
#define AR5K_MISC_DMA_OBS_M 0x000001e0
/*
* QCU/DCU clock gating register (5311)
+ * (reserved4-5)
*/
#define AR5K_QCUDCU_CLKGT 0x005c /* Register Address (?) */
#define AR5K_QCUDCU_CLKGT_QCU 0x0000ffff /* Mask for QCU clock */
#define AR5K_ISR_TXEOL 0x00000400 /* Empty TX descriptor */
#define AR5K_ISR_TXURN 0x00000800 /* Transmit FIFO underrun */
#define AR5K_ISR_MIB 0x00001000 /* Update MIB counters */
-#define AR5K_ISR_SWI 0x00002000 /* Software interrupt (?) */
+#define AR5K_ISR_SWI 0x00002000 /* Software interrupt */
#define AR5K_ISR_RXPHY 0x00004000 /* PHY error */
-#define AR5K_ISR_RXKCM 0x00008000
+#define AR5K_ISR_RXKCM 0x00008000 /* RX Key cache miss */
#define AR5K_ISR_SWBA 0x00010000 /* Software beacon alert */
#define AR5K_ISR_BRSSI 0x00020000
#define AR5K_ISR_BMISS 0x00040000 /* Beacon missed */
#define AR5K_ISR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */
#define AR5K_ISR_BNR 0x00100000 /* Beacon not ready [5211+] */
-#define AR5K_ISR_MCABT 0x00100000 /* [5210] */
-#define AR5K_ISR_RXCHIRP 0x00200000 /* [5212+] */
-#define AR5K_ISR_SSERR 0x00200000 /* [5210] */
-#define AR5K_ISR_DPERR 0x00400000 /* [5210] */
+#define AR5K_ISR_MCABT 0x00100000 /* Master Cycle Abort [5210] */
+#define AR5K_ISR_RXCHIRP 0x00200000 /* CHIRP Received [5212+] */
+#define AR5K_ISR_SSERR 0x00200000 /* Signaled System Error [5210] */
+#define AR5K_ISR_DPERR 0x00400000 /* Det par Error (?) [5210] */
#define AR5K_ISR_TIM 0x00800000 /* [5210] */
#define AR5K_ISR_BCNMISC 0x00800000 /* [5212+] */
#define AR5K_ISR_GPIO 0x01000000 /* GPIO (rf kill)*/
#define AR5K_SISR2 0x008c /* Register Address [5211+] */
#define AR5K_SISR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */
-#define AR5K_SISR2_MCABT 0x00100000
-#define AR5K_SISR2_SSERR 0x00200000
-#define AR5K_SISR2_DPERR 0x00400000
+#define AR5K_SISR2_MCABT 0x00100000 /* Master Cycle Abort */
+#define AR5K_SISR2_SSERR 0x00200000 /* Signaled System Error */
+#define AR5K_SISR2_DPERR 0x00400000 /* Det par Error (?) */
#define AR5K_SISR2_TIM 0x01000000 /* [5212+] */
#define AR5K_SISR2_CAB_END 0x02000000 /* [5212+] */
-#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* [5212+] */
-#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* [5212+] */
-#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* [5212+] */
+#define AR5K_SISR2_DTIM_SYNC 0x04000000 /* DTIM sync lost [5212+] */
+#define AR5K_SISR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */
+#define AR5K_SISR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */
#define AR5K_SISR2_DTIM 0x20000000 /* [5212+] */
#define AR5K_SISR3 0x0090 /* Register Address [5211+] */
#define AR5K_IMR_TXEOL 0x00000400 /* Empty TX descriptor*/
#define AR5K_IMR_TXURN 0x00000800 /* Transmit FIFO underrun*/
#define AR5K_IMR_MIB 0x00001000 /* Update MIB counters*/
-#define AR5K_IMR_SWI 0x00002000
+#define AR5K_IMR_SWI 0x00002000 /* Software interrupt */
#define AR5K_IMR_RXPHY 0x00004000 /* PHY error*/
-#define AR5K_IMR_RXKCM 0x00008000
+#define AR5K_IMR_RXKCM 0x00008000 /* RX Key cache miss */
#define AR5K_IMR_SWBA 0x00010000 /* Software beacon alert*/
#define AR5K_IMR_BRSSI 0x00020000
#define AR5K_IMR_BMISS 0x00040000 /* Beacon missed*/
#define AR5K_IMR_HIUERR 0x00080000 /* Host Interface Unit error [5211+] */
#define AR5K_IMR_BNR 0x00100000 /* Beacon not ready [5211+] */
-#define AR5K_IMR_MCABT 0x00100000 /* [5210] */
-#define AR5K_IMR_RXCHIRP 0x00200000 /* [5212+]*/
-#define AR5K_IMR_SSERR 0x00200000 /* [5210] */
-#define AR5K_IMR_DPERR 0x00400000 /* [5210] */
+#define AR5K_IMR_MCABT 0x00100000 /* Master Cycle Abort [5210] */
+#define AR5K_IMR_RXCHIRP 0x00200000 /* CHIRP Received [5212+]*/
+#define AR5K_IMR_SSERR 0x00200000 /* Signaled System Error [5210] */
+#define AR5K_IMR_DPERR 0x00400000 /* Det par Error (?) [5210] */
#define AR5K_IMR_TIM 0x00800000 /* [5211+] */
#define AR5K_IMR_BCNMISC 0x00800000 /* [5212+] */
#define AR5K_IMR_GPIO 0x01000000 /* GPIO (rf kill)*/
#define AR5K_SIMR2 0x00ac /* Register Address [5211+] */
#define AR5K_SIMR2_QCU_TXURN 0x000003ff /* Mask for QCU_TXURN */
#define AR5K_SIMR2_QCU_TXURN_S 0
-#define AR5K_SIMR2_MCABT 0x00100000
-#define AR5K_SIMR2_SSERR 0x00200000
-#define AR5K_SIMR2_DPERR 0x00400000
+#define AR5K_SIMR2_MCABT 0x00100000 /* Master Cycle Abort */
+#define AR5K_SIMR2_SSERR 0x00200000 /* Signaled System Error */
+#define AR5K_SIMR2_DPERR 0x00400000 /* Det par Error (?) */
#define AR5K_SIMR2_TIM 0x01000000 /* [5212+] */
#define AR5K_SIMR2_CAB_END 0x02000000 /* [5212+] */
-#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* [5212+] */
-#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* [5212+] */
-#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* [5212+] */
+#define AR5K_SIMR2_DTIM_SYNC 0x04000000 /* DTIM Sync lost [5212+] */
+#define AR5K_SIMR2_BCN_TIMEOUT 0x08000000 /* Beacon Timeout [5212+] */
+#define AR5K_SIMR2_CAB_TIMEOUT 0x10000000 /* CAB Timeout [5212+] */
#define AR5K_SIMR2_DTIM 0x20000000 /* [5212+] */
#define AR5K_SIMR3 0x00b0 /* Register Address [5211+] */
#define AR5K_SIMR4_QTRIG 0x000003ff /* Mask for QTRIG */
#define AR5K_SIMR4_QTRIG_S 0
+/*
+ * DMA Debug registers 0-7
+ * 0xe0 - 0xfc
+ */
/*
* Decompression mask registers [5212+]
*/
-#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (?)*/
-#define AR5K_DCM_DATA 0x0404 /*Decompression mask data (?)*/
+#define AR5K_DCM_ADDR 0x0400 /*Decompression mask address (index) */
+#define AR5K_DCM_DATA 0x0404 /*Decompression mask data */
+
+/*
+ * Wake On Wireless pattern control register [5212+]
+ */
+#define AR5K_WOW_PCFG 0x0410 /* Register Address */
+#define AR5K_WOW_PCFG_PAT_MATCH_EN 0x00000001 /* Pattern match enable */
+#define AR5K_WOW_PCFG_LONG_FRAME_POL 0x00000002 /* Long frame policy */
+#define AR5K_WOW_PCFG_WOBMISS 0x00000004 /* Wake on bea(con) miss (?) */
+#define AR5K_WOW_PCFG_PAT_0_EN 0x00000100 /* Enable pattern 0 */
+#define AR5K_WOW_PCFG_PAT_1_EN 0x00000200 /* Enable pattern 1 */
+#define AR5K_WOW_PCFG_PAT_2_EN 0x00000400 /* Enable pattern 2 */
+#define AR5K_WOW_PCFG_PAT_3_EN 0x00000800 /* Enable pattern 3 */
+#define AR5K_WOW_PCFG_PAT_4_EN 0x00001000 /* Enable pattern 4 */
+#define AR5K_WOW_PCFG_PAT_5_EN 0x00002000 /* Enable pattern 5 */
+
+/*
+ * Wake On Wireless pattern index register (?) [5212+]
+ */
+#define AR5K_WOW_PAT_IDX 0x0414
+
+/*
+ * Wake On Wireless pattern data register [5212+]
+ */
+#define AR5K_WOW_PAT_DATA 0x0418 /* Register Address */
+#define AR5K_WOW_PAT_DATA_0_3_V 0x00000001 /* Pattern 0, 3 value */
+#define AR5K_WOW_PAT_DATA_1_4_V 0x00000100 /* Pattern 1, 4 value */
+#define AR5K_WOW_PAT_DATA_2_5_V 0x00010000 /* Pattern 2, 5 value */
+#define AR5K_WOW_PAT_DATA_0_3_M 0x01000000 /* Pattern 0, 3 mask */
+#define AR5K_WOW_PAT_DATA_1_4_M 0x04000000 /* Pattern 1, 4 mask */
+#define AR5K_WOW_PAT_DATA_2_5_M 0x10000000 /* Pattern 2, 5 mask */
/*
* Decompression configuration registers [5212+]
*/
-#define AR5K_DCCFG 0x0420
+#define AR5K_DCCFG 0x0420 /* Register Address */
+#define AR5K_DCCFG_GLOBAL_EN 0x00000001 /* Enable decompression on all queues */
+#define AR5K_DCCFG_BYPASS_EN 0x00000002 /* Bypass decompression */
+#define AR5K_DCCFG_BCAST_EN 0x00000004 /* Enable decompression for bcast frames */
+#define AR5K_DCCFG_MCAST_EN 0x00000008 /* Enable decompression for mcast frames */
/*
* Compression configuration registers [5212+]
*/
-#define AR5K_CCFG 0x0600
-#define AR5K_CCFG_CUP 0x0604
+#define AR5K_CCFG 0x0600 /* Register Address */
+#define AR5K_CCFG_WINDOW_SIZE 0x00000007 /* Compression window size */
+#define AR5K_CCFG_CPC_EN 0x00000008 /* Enable performance counters */
+
+#define AR5K_CCFG_CCU 0x0604 /* Register Address */
+#define AR5K_CCFG_CCU_CUP_EN 0x00000001 /* CCU Catchup enable */
+#define AR5K_CCFG_CCU_CREDIT 0x00000002 /* CCU Credit (field) */
+#define AR5K_CCFG_CCU_CD_THRES 0x00000080 /* CCU Cyc(lic?) debt threshold (field) */
+#define AR5K_CCFG_CCU_CUP_LCNT 0x00010000 /* CCU Catchup lit(?) count */
+#define AR5K_CCFG_CCU_INIT 0x00100200 /* Initial value during reset */
/*
* Compression performance counter registers [5212+]
#define AR5K_CPC1 0x0614 /* Compression performance counter 1*/
#define AR5K_CPC2 0x0618 /* Compression performance counter 2 */
#define AR5K_CPC3 0x061c /* Compression performance counter 3 */
-#define AR5K_CPCORN 0x0620 /* Compression performance overrun (?) */
+#define AR5K_CPCOVF 0x0620 /* Compression performance overflow */
/*
* set/clear, which contain status for all queues (we shift by 1 for each
* queue). To access these registers easily we define some macros here
* that are used inside HAL. For more infos check out *_tx_queue functs.
- *
- * TODO: Boundary checking on macros (here?)
*/
/*
#define AR5K_QCU_RDYTIMECFG_BASE 0x0900 /* Register Address - Queue0 RDYTIMECFG */
#define AR5K_QCU_RDYTIMECFG_INTVAL 0x00ffffff /* Ready time interval mask */
#define AR5K_QCU_RDYTIMECFG_INTVAL_S 0
-#define AR5K_QCU_RDYTIMECFG_DURATION 0x00ffffff /* Ready time duration mask */
#define AR5K_QCU_RDYTIMECFG_ENABLE 0x01000000 /* Ready time enable mask */
#define AR5K_QUEUE_RDYTIMECFG(_q) AR5K_QUEUE_REG(AR5K_QCU_RDYTIMECFG_BASE, _q)
*/
#define AR5K_QCU_MISC_BASE 0x09c0 /* Register Address -Queue0 MISC */
#define AR5K_QCU_MISC_FRSHED_M 0x0000000f /* Frame sheduling mask */
-#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */
-#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */
-#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */
-#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */
+#define AR5K_QCU_MISC_FRSHED_ASAP 0 /* ASAP */
+#define AR5K_QCU_MISC_FRSHED_CBR 1 /* Constant Bit Rate */
+#define AR5K_QCU_MISC_FRSHED_DBA_GT 2 /* DMA Beacon alert gated (?) */
+#define AR5K_QCU_MISC_FRSHED_TIM_GT 3 /* Time gated (?) */
#define AR5K_QCU_MISC_FRSHED_BCN_SENT_GT 4 /* Beacon sent gated (?) */
#define AR5K_QCU_MISC_ONESHOT_ENABLE 0x00000010 /* Oneshot enable */
#define AR5K_QCU_MISC_CBREXP 0x00000020 /* CBR expired (normal queue) */
#define AR5K_QCU_MISC_CBREXP_BCN 0x00000040 /* CBR expired (beacon queue) */
-#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Beacons enabled */
-#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled (?) */
-#define AR5K_QCU_MISC_TXE 0x00000200 /* TXE reset when RDYTIME enalbed (?) */
-#define AR5K_QCU_MISC_CBR 0x00000400 /* CBR threshold reset (?) */
-#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU reset (?) */
+#define AR5K_QCU_MISC_BCN_ENABLE 0x00000080 /* Enable Beacon use */
+#define AR5K_QCU_MISC_CBR_THRES_ENABLE 0x00000100 /* CBR threshold enabled */
+#define AR5K_QCU_MISC_RDY_VEOL_POLICY 0x00000200 /* TXE reset when RDYTIME enalbed */
+#define AR5K_QCU_MISC_CBR_RESET_CNT 0x00000400 /* CBR threshold (counter) reset */
+#define AR5K_QCU_MISC_DCU_EARLY 0x00000800 /* DCU early termination */
+#define AR5K_QCU_MISC_DCU_CMP_EN 0x00001000 /* Enable frame compression */
#define AR5K_QUEUE_MISC(_q) AR5K_QUEUE_REG(AR5K_QCU_MISC_BASE, _q)
*/
#define AR5K_QCU_STS_BASE 0x0a00 /* Register Address - Queue0 STS */
#define AR5K_QCU_STS_FRMPENDCNT 0x00000003 /* Frames pending counter */
-#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter (?) */
+#define AR5K_QCU_STS_CBREXPCNT 0x0000ff00 /* CBR expired counter */
#define AR5K_QUEUE_STATUS(_q) AR5K_QUEUE_REG(AR5K_QCU_STS_BASE, _q)
/*
*/
#define AR5K_QCU_CBB_SELECT 0x0b00
#define AR5K_QCU_CBB_ADDR 0x0b04
+#define AR5K_QCU_CBB_ADDR_S 9
/*
* QCU compression buffer configuration register [5212+]
+ * (buffer size)
*/
#define AR5K_QCU_CBCFG 0x0b08
* No lockout means there is no special handling.
*/
#define AR5K_DCU_MISC_BASE 0x1100 /* Register Address -Queue0 DCU_MISC */
-#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff setting (?) */
+#define AR5K_DCU_MISC_BACKOFF 0x000007ff /* Mask for backoff threshold */
#define AR5K_DCU_MISC_BACKOFF_FRAG 0x00000200 /* Enable backoff while bursting */
-#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll (?) */
-#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff (?) */
-#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch (?) */
+#define AR5K_DCU_MISC_HCFPOLL_ENABLE 0x00000800 /* CF - Poll enable */
+#define AR5K_DCU_MISC_BACKOFF_PERSIST 0x00001000 /* Persistent backoff */
+#define AR5K_DCU_MISC_FRMPRFTCH_ENABLE 0x00002000 /* Enable frame pre-fetch */
#define AR5K_DCU_MISC_VIRTCOL 0x0000c000 /* Mask for Virtual Collision (?) */
-#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0
-#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1
-#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2
-#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Beacon enable (?) */
+#define AR5K_DCU_MISC_VIRTCOL_NORMAL 0
+#define AR5K_DCU_MISC_VIRTCOL_MODIFIED 1
+#define AR5K_DCU_MISC_VIRTCOL_IGNORE 2
+#define AR5K_DCU_MISC_BCN_ENABLE 0x00010000 /* Enable Beacon use */
#define AR5K_DCU_MISC_ARBLOCK_CTL 0x00060000 /* Arbiter lockout control mask */
#define AR5K_DCU_MISC_ARBLOCK_CTL_S 17
-#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */
+#define AR5K_DCU_MISC_ARBLOCK_CTL_NONE 0 /* No arbiter lockout */
#define AR5K_DCU_MISC_ARBLOCK_CTL_INTFRM 1 /* Intra-frame lockout */
#define AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL 2 /* Global lockout */
-#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000
-#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment (?) */
-#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff (?) */
-#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision policy (?) */
-#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000
+#define AR5K_DCU_MISC_ARBLOCK_IGNORE 0x00080000 /* Ignore Arbiter lockout */
+#define AR5K_DCU_MISC_SEQ_NUM_INCR_DIS 0x00100000 /* Disable sequence number increment */
+#define AR5K_DCU_MISC_POST_FR_BKOFF_DIS 0x00200000 /* Disable post-frame backoff */
+#define AR5K_DCU_MISC_VIRT_COLL_POLICY 0x00400000 /* Virtual Collision cw policy */
+#define AR5K_DCU_MISC_BLOWN_IFS_POLICY 0x00800000 /* Blown IFS policy (?) */
#define AR5K_DCU_MISC_SEQNUM_CTL 0x01000000 /* Sequence number control (?) */
#define AR5K_QUEUE_DFS_MISC(_q) AR5K_QUEUE_REG(AR5K_DCU_MISC_BASE, _q)
/*
* DCU frame sequence number registers
*/
-#define AR5K_DCU_SEQNUM_BASE 0x1140
-#define AR5K_DCU_SEQNUM_M 0x00000fff
+#define AR5K_DCU_SEQNUM_BASE 0x1140
+#define AR5K_DCU_SEQNUM_M 0x00000fff
#define AR5K_QUEUE_DFS_SEQNUM(_q) AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q)
/*
- * DCU global IFS SIFS registers
+ * DCU global IFS SIFS register
*/
#define AR5K_DCU_GBL_IFS_SIFS 0x1030
#define AR5K_DCU_GBL_IFS_SIFS_M 0x0000ffff
/*
- * DCU global IFS slot interval registers
+ * DCU global IFS slot interval register
*/
#define AR5K_DCU_GBL_IFS_SLOT 0x1070
#define AR5K_DCU_GBL_IFS_SLOT_M 0x0000ffff
/*
- * DCU global IFS EIFS registers
+ * DCU global IFS EIFS register
*/
#define AR5K_DCU_GBL_IFS_EIFS 0x10b0
#define AR5K_DCU_GBL_IFS_EIFS_M 0x0000ffff
/*
- * DCU global IFS misc registers
+ * DCU global IFS misc register
+ *
+ * LFSR stands for Linear Feedback Shift Register
+ * and it's used for generating pseudo-random
+ * number sequences.
+ *
+ * (If i understand corectly, random numbers are
+ * used for idle sensing -multiplied with cwmin/max etc-)
*/
#define AR5K_DCU_GBL_IFS_MISC 0x10f0 /* Register Address */
-#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007
-#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode (?) */
-#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask (?) */
-#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00
-#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000
+#define AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE 0x00000007 /* LFSR Slice Select */
+#define AR5K_DCU_GBL_IFS_MISC_TURBO_MODE 0x00000008 /* Turbo mode */
+#define AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC 0x000003f0 /* SIFS Duration mask */
+#define AR5K_DCU_GBL_IFS_MISC_USEC_DUR 0x000ffc00 /* USEC Duration mask */
+#define AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY 0x00300000 /* DCU Arbiter delay mask */
+#define AR5K_DCU_GBL_IFS_MISC_SIFS_CNT_RST 0x00400000 /* SIFC cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_AIFS_CNT_RST 0x00800000 /* AIFS cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_RND_LFSR_SL_DIS 0x01000000 /* Disable random LFSR slice */
/*
* DCU frame prefetch control register
*/
-#define AR5K_DCU_FP 0x1230
+#define AR5K_DCU_FP 0x1230 /* Register Address */
+#define AR5K_DCU_FP_NOBURST_DCU_EN 0x00000001 /* Enable non-burst prefetch on DCU (?) */
+#define AR5K_DCU_FP_NOBURST_EN 0x00000010 /* Enable non-burst prefetch (?) */
+#define AR5K_DCU_FP_BURST_DCU_EN 0x00000020 /* Enable burst prefetch on DCU (?) */
/*
* DCU transmit pause control/status register
*/
#define AR5K_DCU_TXP 0x1270 /* Register Address */
-#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask (?) */
-#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status (?) */
+#define AR5K_DCU_TXP_M 0x000003ff /* Tx pause mask */
+#define AR5K_DCU_TXP_STATUS 0x00010000 /* Tx pause status */
+
+/*
+ * DCU transmit filter table 0 (32 entries)
+ */
+#define AR5K_DCU_TX_FILTER_0_BASE 0x1038
+#define AR5K_DCU_TX_FILTER_0(_n) (AR5K_DCU_TX_FILTER_0_BASE + (_n * 64))
/*
- * DCU transmit filter register
+ * DCU transmit filter table 1 (16 entries)
*/
-#define AR5K_DCU_TX_FILTER 0x1038
+#define AR5K_DCU_TX_FILTER_1_BASE 0x103c
+#define AR5K_DCU_TX_FILTER_1(_n) (AR5K_DCU_TX_FILTER_1_BASE + ((_n - 32) * 64))
/*
* DCU clear transmit filter register
/*
* Reset control register
- *
- * 4 and 8 are not used in 5211/5212 and
- * 2 means "baseband reset" on 5211/5212.
*/
#define AR5K_RESET_CTL 0x4000 /* Register Address */
#define AR5K_RESET_CTL_PCU 0x00000001 /* Protocol Control Unit reset */
#define AR5K_SLEEP_CTL_SLE_SLP 0x00010000 /* Force chip sleep */
#define AR5K_SLEEP_CTL_SLE_ALLOW 0x00020000
#define AR5K_SLEEP_CTL_SLE_UNITS 0x00000008 /* [5211+] */
+/* more bits */
/*
* Interrupt pending register
* Sleep force register
*/
#define AR5K_SFR 0x400c
-#define AR5K_SFR_M 0x00000001
+#define AR5K_SFR_EN 0x00000001
/*
* PCI configuration register
*/
#define AR5K_PCICFG 0x4010 /* Register Address */
#define AR5K_PCICFG_EEAE 0x00000001 /* Eeprom access enable [5210] */
+#define AR5K_PCICFG_SLEEP_CLOCK_EN 0x00000002 /* Enable sleep clock (?) */
#define AR5K_PCICFG_CLKRUNEN 0x00000004 /* CLKRUN enable [5211+] */
#define AR5K_PCICFG_EESIZE 0x00000018 /* Mask for EEPROM size [5211+] */
#define AR5K_PCICFG_EESIZE_S 3
#define AR5K_PCICFG_CBEFIX_DIS 0x00000400 /* Disable CBE fix (?) */
#define AR5K_PCICFG_SL_INTEN 0x00000800 /* Enable interrupts when asleep (?) */
#define AR5K_PCICFG_LED_BCTL 0x00001000 /* Led blink (?) [5210] */
-#define AR5K_PCICFG_SL_INPEN 0x00002800 /* Sleep even whith pending interrupts (?) */
+#define AR5K_PCICFG_UNK 0x00001000 /* Passed on some parts durring attach (?) */
+#define AR5K_PCICFG_SL_INPEN 0x00002000 /* Sleep even whith pending interrupts (?) */
#define AR5K_PCICFG_SPWR_DN 0x00010000 /* Mask for power status */
#define AR5K_PCICFG_LEDMODE 0x000e0000 /* Ledmode [5211+] */
#define AR5K_PCICFG_LEDMODE_PROP 0x00000000 /* Blink on standard traffic [5211+] */
#define AR5K_PCICFG_LEDMODE_PROM 0x00020000 /* Default mode (blink on any traffic) [5211+] */
#define AR5K_PCICFG_LEDMODE_PWR 0x00040000 /* Some other blinking mode (?) [5211+] */
#define AR5K_PCICFG_LEDMODE_RAND 0x00060000 /* Random blinking (?) [5211+] */
-#define AR5K_PCICFG_LEDBLINK 0x00700000
+#define AR5K_PCICFG_LEDBLINK 0x00700000 /* Led blink rate */
#define AR5K_PCICFG_LEDBLINK_S 20
-#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slow led blink rate (?) [5211+] */
+#define AR5K_PCICFG_LEDSLOW 0x00800000 /* Slowest led blink rate [5211+] */
#define AR5K_PCICFG_LEDSTATE \
(AR5K_PCICFG_LED | AR5K_PCICFG_LEDMODE | \
AR5K_PCICFG_LEDBLINK | AR5K_PCICFG_LEDSLOW)
+#define AR5K_PCICFG_SLEEP_CLOCK_RATE 0x03000000 /* Sleep clock rate (field) */
/*
* "General Purpose Input/Output" (GPIO) control register
#define AR5K_EEPROM_VERSION_4_4 0x4004
#define AR5K_EEPROM_VERSION_4_5 0x4005
#define AR5K_EEPROM_VERSION_4_6 0x4006 /* has ee_scaled_cck_delta */
-#define AR5K_EEPROM_VERSION_4_7 0x3007
+#define AR5K_EEPROM_VERSION_4_7 0x4007
#define AR5K_EEPROM_MODE_11A 0
#define AR5K_EEPROM_MODE_11B 1
#define AR5K_EEPROM_STAT_WRDONE 0x00000008 /* EEPROM write successful */
/*
- * EEPROM config register (?)
+ * EEPROM config register
*/
-#define AR5K_EEPROM_CFG 0x6010
-
+#define AR5K_EEPROM_CFG 0x6010 /* Register Addres */
+#define AR5K_EEPROM_CFG_SIZE_OVR 0x00000001
+#define AR5K_EEPROM_CFG_WR_WAIT_DIS 0x00000004 /* Disable write wait */
+#define AR5K_EEPROM_CFG_CLK_RATE 0x00000018 /* Clock rate */
+#define AR5K_EEPROM_CFG_PROT_KEY 0x00ffff00 /* Protectio key */
+#define AR5K_EEPROM_CFG_LIND_EN 0x01000000 /* Enable length indicator (?) */
/*
#define AR5K_STA_ID1 0x8004 /* Register Address */
#define AR5K_STA_ID1_AP 0x00010000 /* Set AP mode */
#define AR5K_STA_ID1_ADHOC 0x00020000 /* Set Ad-Hoc mode */
-#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting (?) */
+#define AR5K_STA_ID1_PWR_SV 0x00040000 /* Power save reporting */
#define AR5K_STA_ID1_NO_KEYSRCH 0x00080000 /* No key search */
#define AR5K_STA_ID1_NO_PSPOLL 0x00100000 /* No power save polling [5210] */
#define AR5K_STA_ID1_PCF_5211 0x00100000 /* Enable PCF on [5211+] */
AR5K_STA_ID1_PCF_5210 : AR5K_STA_ID1_PCF_5211)
#define AR5K_STA_ID1_DEFAULT_ANTENNA 0x00200000 /* Use default antenna */
#define AR5K_STA_ID1_DESC_ANTENNA 0x00400000 /* Update antenna from descriptor */
-#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS (?) */
-#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS (?) */
+#define AR5K_STA_ID1_RTS_DEF_ANTENNA 0x00800000 /* Use default antenna for RTS */
+#define AR5K_STA_ID1_ACKCTS_6MB 0x01000000 /* Use 6Mbit/s for ACK/CTS */
#define AR5K_STA_ID1_BASE_RATE_11B 0x02000000 /* Use 11b base rate (for ACK/CTS ?) [5211+] */
+#define AR5K_STA_ID1_SELF_GEN_SECTORE 0x04000000 /* Self generate sectore (?) */
+#define AR5K_STA_ID1_CRYPT_MIC_EN 0x08000000 /* Enable MIC */
+#define AR5K_STA_ID1_KEYSRCH_MODE 0x10000000 /* Keysearch mode (?) */
+#define AR5K_STA_ID1_PRESERVE_SEQ_NUM 0x20000000 /* Preserve sequence number */
/*
* First BSSID register (MAC address, lower 32bits)
*
* Retry limit register for 5210 (no QCU/DCU so it's done in PCU)
*/
-#define AR5K_NODCU_RETRY_LMT 0x801c /*Register Address */
+#define AR5K_NODCU_RETRY_LMT 0x801c /* Register Address */
#define AR5K_NODCU_RETRY_LMT_SH_RETRY 0x0000000f /* Short retry limit mask */
#define AR5K_NODCU_RETRY_LMT_SH_RETRY_S 0
#define AR5K_NODCU_RETRY_LMT_LG_RETRY 0x000000f0 /* Long retry mask */
#define AR5K_USEC_5211 0x801c /* Register Address [5211+] */
#define AR5K_USEC (ah->ah_version == AR5K_AR5210 ? \
AR5K_USEC_5210 : AR5K_USEC_5211)
-#define AR5K_USEC_1 0x0000007f
+#define AR5K_USEC_1 0x0000007f /* clock cycles for 1us */
#define AR5K_USEC_1_S 0
-#define AR5K_USEC_32 0x00003f80
+#define AR5K_USEC_32 0x00003f80 /* clock cycles for 1us while on 32Mhz clock */
#define AR5K_USEC_32_S 7
#define AR5K_USEC_TX_LATENCY_5211 0x007fc000
#define AR5K_USEC_TX_LATENCY_5211_S 14
/*
* PCU beacon control register
*/
-#define AR5K_BEACON_5210 0x8024
-#define AR5K_BEACON_5211 0x8020
+#define AR5K_BEACON_5210 0x8024 /*Register Address [5210] */
+#define AR5K_BEACON_5211 0x8020 /*Register Address [5211+] */
#define AR5K_BEACON (ah->ah_version == AR5K_AR5210 ? \
AR5K_BEACON_5210 : AR5K_BEACON_5211)
-#define AR5K_BEACON_PERIOD 0x0000ffff
+#define AR5K_BEACON_PERIOD 0x0000ffff /* Mask for beacon period */
#define AR5K_BEACON_PERIOD_S 0
-#define AR5K_BEACON_TIM 0x007f0000
+#define AR5K_BEACON_TIM 0x007f0000 /* Mask for TIM offset */
#define AR5K_BEACON_TIM_S 16
-#define AR5K_BEACON_ENABLE 0x00800000
-#define AR5K_BEACON_RESET_TSF 0x01000000
+#define AR5K_BEACON_ENABLE 0x00800000 /* Enable beacons */
+#define AR5K_BEACON_RESET_TSF 0x01000000 /* Force TSF reset */
/*
* CFP period register
/*
* Receive filter register
- * TODO: Get these out of ar5xxx.h on ath5k
*/
#define AR5K_RX_FILTER_5210 0x804c /* Register Address [5210] */
#define AR5K_RX_FILTER_5211 0x803c /* Register Address [5211+] */
#define AR5K_DIAG_SW_5211 0x8048 /* Register Address [5211+] */
#define AR5K_DIAG_SW (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_5210 : AR5K_DIAG_SW_5211)
-#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001
-#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs (?) */
-#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs (?) */
-#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption (?) */
-#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption (?) */
+#define AR5K_DIAG_SW_DIS_WEP_ACK 0x00000001 /* Disable ACKs if WEP key is invalid */
+#define AR5K_DIAG_SW_DIS_ACK 0x00000002 /* Disable ACKs */
+#define AR5K_DIAG_SW_DIS_CTS 0x00000004 /* Disable CTSs */
+#define AR5K_DIAG_SW_DIS_ENC 0x00000008 /* Disable encryption */
+#define AR5K_DIAG_SW_DIS_DEC 0x00000010 /* Disable decryption */
#define AR5K_DIAG_SW_DIS_TX 0x00000020 /* Disable transmit [5210] */
#define AR5K_DIAG_SW_DIS_RX_5210 0x00000040 /* Disable recieve */
#define AR5K_DIAG_SW_DIS_RX_5211 0x00000020
#define AR5K_DIAG_SW_CHAN_INFO_5211 0x00000100
#define AR5K_DIAG_SW_CHAN_INFO (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_CHAN_INFO_5210 : AR5K_DIAG_SW_CHAN_INFO_5211)
-#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Scrambler seed (?) */
+#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211 0x00000200 /* Enable scrambler seed */
#define AR5K_DIAG_SW_EN_SCRAM_SEED_5210 0x00000400
#define AR5K_DIAG_SW_EN_SCRAM_SEED (ah->ah_version == AR5K_AR5210 ? \
AR5K_DIAG_SW_EN_SCRAM_SEED_5210 : AR5K_DIAG_SW_EN_SCRAM_SEED_5211)
#define AR5K_DIAG_SW_ECO_ENABLE 0x00000400 /* [5211+] */
#define AR5K_DIAG_SW_SCVRAM_SEED 0x0003f800 /* [5210] */
-#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask (?) */
+#define AR5K_DIAG_SW_SCRAM_SEED_M 0x0001fc00 /* Scrambler seed mask */
#define AR5K_DIAG_SW_SCRAM_SEED_S 10
#define AR5K_DIAG_SW_DIS_SEQ_INC 0x00040000 /* Disable seqnum increment (?)[5210] */
#define AR5K_DIAG_SW_FRAME_NV0_5210 0x00080000
AR5K_DIAG_SW_FRAME_NV0_5210 : AR5K_DIAG_SW_FRAME_NV0_5211)
#define AR5K_DIAG_SW_OBSPT_M 0x000c0000
#define AR5K_DIAG_SW_OBSPT_S 18
+/* more bits */
/*
* TSF (clock) register (lower 32 bits)
/*
* ADDAC test register [5211+]
*/
-#define AR5K_ADDAC_TEST 0x8054
-#define AR5K_ADDAC_TEST_TXCONT 0x00000001
+#define AR5K_ADDAC_TEST 0x8054 /* Register Address */
+#define AR5K_ADDAC_TEST_TXCONT 0x00000001 /* Test continuous tx */
+#define AR5K_ADDAC_TEST_TST_MODE 0x00000002 /* Test mode */
+#define AR5K_ADDAC_TEST_LOOP_EN 0x00000004 /* Enable loop */
+#define AR5K_ADDAC_TEST_LOOP_LEN 0x00000008 /* Loop length (field) */
+#define AR5K_ADDAC_TEST_USE_U8 0x00004000 /* Use upper 8 bits */
+#define AR5K_ADDAC_TEST_MSB 0x00008000 /* State of MSB */
+#define AR5K_ADDAC_TEST_TRIG_SEL 0x00010000 /* Trigger select */
+#define AR5K_ADDAC_TEST_TRIG_PTY 0x00020000 /* Trigger polarity */
+#define AR5K_ADDAC_TEST_RXCONT 0x00040000 /* Continuous capture */
+#define AR5K_ADDAC_TEST_CAPTURE 0x00080000 /* Begin capture */
+#define AR5K_ADDAC_TEST_TST_ARM 0x00100000 /* Test ARM (Adaptive Radio Mode ?) */
/*
* Default antenna register [5211+]
*/
#define AR5K_DEFAULT_ANTENNA 0x8058
+/*
+ * Frame control QoS mask register (?) [5211+]
+ * (FC_QOS_MASK)
+ */
+#define AR5K_FRAME_CTL_QOSM 0x805c
+/*
+ * Seq mask register (?) [5211+]
+ */
+#define AR5K_SEQ_MASK 0x8060
/*
* Retry count register [5210]
/*
* XR (eXtended Range) mode register
*/
-#define AR5K_XRMODE 0x80c0
-#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f
+#define AR5K_XRMODE 0x80c0 /* Register Address */
+#define AR5K_XRMODE_POLL_TYPE_M 0x0000003f /* Mask for Poll type (?) */
#define AR5K_XRMODE_POLL_TYPE_S 0
-#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c
+#define AR5K_XRMODE_POLL_SUBTYPE_M 0x0000003c /* Mask for Poll subtype (?) */
#define AR5K_XRMODE_POLL_SUBTYPE_S 2
-#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080
-#define AR5K_XRMODE_SIFS_DELAY 0x000fff00
-#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000
+#define AR5K_XRMODE_POLL_WAIT_ALL 0x00000080 /* Wait for poll */
+#define AR5K_XRMODE_SIFS_DELAY 0x000fff00 /* Mask for SIFS delay */
+#define AR5K_XRMODE_FRAME_HOLD_M 0xfff00000 /* Mask for frame hold (?) */
#define AR5K_XRMODE_FRAME_HOLD_S 20
/*
* XR delay register
*/
-#define AR5K_XRDELAY 0x80c4
-#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff
+#define AR5K_XRDELAY 0x80c4 /* Register Address */
+#define AR5K_XRDELAY_SLOT_DELAY_M 0x0000ffff /* Mask for slot delay */
#define AR5K_XRDELAY_SLOT_DELAY_S 0
-#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000
+#define AR5K_XRDELAY_CHIRP_DELAY_M 0xffff0000 /* Mask for CHIRP data delay */
#define AR5K_XRDELAY_CHIRP_DELAY_S 16
/*
* XR timeout register
*/
-#define AR5K_XRTIMEOUT 0x80c8
-#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff
+#define AR5K_XRTIMEOUT 0x80c8 /* Register Address */
+#define AR5K_XRTIMEOUT_CHIRP_M 0x0000ffff /* Mask for CHIRP timeout */
#define AR5K_XRTIMEOUT_CHIRP_S 0
-#define AR5K_XRTIMEOUT_POLL_M 0xffff0000
+#define AR5K_XRTIMEOUT_POLL_M 0xffff0000 /* Mask for Poll timeout */
#define AR5K_XRTIMEOUT_POLL_S 16
/*
* XR chirp register
*/
-#define AR5K_XRCHIRP 0x80cc
-#define AR5K_XRCHIRP_SEND 0x00000001
-#define AR5K_XRCHIRP_GAP 0xffff0000
+#define AR5K_XRCHIRP 0x80cc /* Register Address */
+#define AR5K_XRCHIRP_SEND 0x00000001 /* Send CHIRP */
+#define AR5K_XRCHIRP_GAP 0xffff0000 /* Mask for CHIRP gap (?) */
/*
* XR stomp register
*/
-#define AR5K_XRSTOMP 0x80d0
-#define AR5K_XRSTOMP_TX 0x00000001
-#define AR5K_XRSTOMP_RX_ABORT 0x00000002
-#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00
+#define AR5K_XRSTOMP 0x80d0 /* Register Address */
+#define AR5K_XRSTOMP_TX 0x00000001 /* Stomp Tx (?) */
+#define AR5K_XRSTOMP_RX 0x00000002 /* Stomp Rx (?) */
+#define AR5K_XRSTOMP_TX_RSSI 0x00000004 /* Stomp Tx RSSI (?) */
+#define AR5K_XRSTOMP_TX_BSSID 0x00000008 /* Stomp Tx BSSID (?) */
+#define AR5K_XRSTOMP_DATA 0x00000010 /* Stomp data (?)*/
+#define AR5K_XRSTOMP_RSSI_THRES 0x0000ff00 /* Mask for XR RSSI threshold */
/*
* First enhanced sleep register
*/
-#define AR5K_SLEEP0 0x80d4
-#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff
+#define AR5K_SLEEP0 0x80d4 /* Register Address */
+#define AR5K_SLEEP0_NEXT_DTIM 0x0007ffff /* Mask for next DTIM (?) */
#define AR5K_SLEEP0_NEXT_DTIM_S 0
-#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000
-#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000
-#define AR5K_SLEEP0_CABTO 0xff000000
+#define AR5K_SLEEP0_ASSUME_DTIM 0x00080000 /* Assume DTIM */
+#define AR5K_SLEEP0_ENH_SLEEP_EN 0x00100000 /* Enable enchanced sleep control */
+#define AR5K_SLEEP0_CABTO 0xff000000 /* Mask for CAB Time Out */
#define AR5K_SLEEP0_CABTO_S 24
/*
* Second enhanced sleep register
*/
-#define AR5K_SLEEP1 0x80d8
-#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff
+#define AR5K_SLEEP1 0x80d8 /* Register Address */
+#define AR5K_SLEEP1_NEXT_TIM 0x0007ffff /* Mask for next TIM (?) */
#define AR5K_SLEEP1_NEXT_TIM_S 0
-#define AR5K_SLEEP1_BEACON_TO 0xff000000
+#define AR5K_SLEEP1_BEACON_TO 0xff000000 /* Mask for Beacon Time Out */
#define AR5K_SLEEP1_BEACON_TO_S 24
/*
* Third enhanced sleep register
*/
-#define AR5K_SLEEP2 0x80dc
-#define AR5K_SLEEP2_TIM_PER 0x0000ffff
+#define AR5K_SLEEP2 0x80dc /* Register Address */
+#define AR5K_SLEEP2_TIM_PER 0x0000ffff /* Mask for TIM period (?) */
#define AR5K_SLEEP2_TIM_PER_S 0
-#define AR5K_SLEEP2_DTIM_PER 0xffff0000
+#define AR5K_SLEEP2_DTIM_PER 0xffff0000 /* Mask for DTIM period (?) */
#define AR5K_SLEEP2_DTIM_PER_S 16
/*
* BSSID mask registers
*/
-#define AR5K_BSS_IDM0 0x80e0
-#define AR5K_BSS_IDM1 0x80e4
+#define AR5K_BSS_IDM0 0x80e0 /* Upper bits */
+#define AR5K_BSS_IDM1 0x80e4 /* Lower bits */
/*
* TX power control (TPC) register
+ *
+ * XXX: PCDAC steps (0.5dbm) or DBM ?
+ *
+ * XXX: Mask changes for newer chips to 7f
+ * like tx power table ?
*/
-#define AR5K_TXPC 0x80e8
-#define AR5K_TXPC_ACK_M 0x0000003f
+#define AR5K_TXPC 0x80e8 /* Register Address */
+#define AR5K_TXPC_ACK_M 0x0000003f /* Mask for ACK tx power */
#define AR5K_TXPC_ACK_S 0
-#define AR5K_TXPC_CTS_M 0x00003f00
+#define AR5K_TXPC_CTS_M 0x00003f00 /* Mask for CTS tx power */
#define AR5K_TXPC_CTS_S 8
-#define AR5K_TXPC_CHIRP_M 0x003f0000
+#define AR5K_TXPC_CHIRP_M 0x003f0000 /* Mask for CHIRP tx power */
#define AR5K_TXPC_CHIRP_S 22
/*
* Profile count registers
*/
-#define AR5K_PROFCNT_TX 0x80ec
-#define AR5K_PROFCNT_RX 0x80f0
-#define AR5K_PROFCNT_RXCLR 0x80f4
-#define AR5K_PROFCNT_CYCLE 0x80f8
+#define AR5K_PROFCNT_TX 0x80ec /* Tx count */
+#define AR5K_PROFCNT_RX 0x80f0 /* Rx count */
+#define AR5K_PROFCNT_RXCLR 0x80f4 /* Clear Rx count */
+#define AR5K_PROFCNT_CYCLE 0x80f8 /* Cycle count (?) */
+
+/*
+ * Quiet (period) control registers (?)
+ */
+#define AR5K_QUIET_CTL1 0x80fc /* Register Address */
+#define AR5K_QUIET_CTL1_NEXT_QT 0x0000ffff /* Mask for next quiet (period?) (?) */
+#define AR5K_QUIET_CTL1_QT_EN 0x00010000 /* Enable quiet (period?) */
+#define AR5K_QUIET_CTL2 0x8100 /* Register Address */
+#define AR5K_QUIET_CTL2_QT_PER 0x0000ffff /* Mask for quiet period (?) */
+#define AR5K_QUIET_CTL2_QT_DUR 0xffff0000 /* Mask for quiet duration (?) */
/*
* TSF parameter register
*/
-#define AR5K_TSF_PARM 0x8104
-#define AR5K_TSF_PARM_INC_M 0x000000ff
+#define AR5K_TSF_PARM 0x8104 /* Register Address */
+#define AR5K_TSF_PARM_INC_M 0x000000ff /* Mask for TSF increment */
#define AR5K_TSF_PARM_INC_S 0
+/*
+ * QoS register (?)
+ */
+#define AR5K_QOS 0x8108 /* Register Address */
+#define AR5K_QOS_NOACK_2BIT_VALUES 0x00000000 /* (field) */
+#define AR5K_QOS_NOACK_BIT_OFFSET 0x00000020 /* (field) */
+#define AR5K_QOS_NOACK_BYTE_OFFSET 0x00000080 /* (field) */
+
/*
* PHY error filter register
*/
#define AR5K_PHY_ERR_FIL 0x810c
-#define AR5K_PHY_ERR_FIL_RADAR 0x00000020
-#define AR5K_PHY_ERR_FIL_OFDM 0x00020000
-#define AR5K_PHY_ERR_FIL_CCK 0x02000000
+#define AR5K_PHY_ERR_FIL_RADAR 0x00000020 /* Radar signal */
+#define AR5K_PHY_ERR_FIL_OFDM 0x00020000 /* OFDM false detect (ANI) */
+#define AR5K_PHY_ERR_FIL_CCK 0x02000000 /* CCK false detect (ANI) */
+
+/*
+ * XR latency register
+ */
+#define AR5K_XRLAT_TX 0x8110
/*
- * Rate duration register
+ * ACK SIFS register
+ */
+#define AR5K_ACKSIFS 0x8114 /* Register Address */
+#define AR5K_ACKSIFS_INC 0x00000000 /* ACK SIFS Increment (field) */
+
+/*
+ * MIC QoS control register (?)
+ */
+#define AR5K_MIC_QOS_CTL 0x8118 /* Register Address */
+#define AR5K_MIC_QOS_CTL_0 0x00000001 /* MIC QoS control 0 (?) */
+#define AR5K_MIC_QOS_CTL_1 0x00000004 /* MIC QoS control 1 (?) */
+#define AR5K_MIC_QOS_CTL_2 0x00000010 /* MIC QoS control 2 (?) */
+#define AR5K_MIC_QOS_CTL_3 0x00000040 /* MIC QoS control 3 (?) */
+#define AR5K_MIC_QOS_CTL_4 0x00000100 /* MIC QoS control 4 (?) */
+#define AR5K_MIC_QOS_CTL_5 0x00000400 /* MIC QoS control 5 (?) */
+#define AR5K_MIC_QOS_CTL_6 0x00001000 /* MIC QoS control 6 (?) */
+#define AR5K_MIC_QOS_CTL_7 0x00004000 /* MIC QoS control 7 (?) */
+#define AR5K_MIC_QOS_CTL_MQ_EN 0x00010000 /* Enable MIC QoS */
+
+/*
+ * MIC QoS select register (?)
+ */
+#define AR5K_MIC_QOS_SEL 0x811c
+#define AR5K_MIC_QOS_SEL_0 0x00000001
+#define AR5K_MIC_QOS_SEL_1 0x00000010
+#define AR5K_MIC_QOS_SEL_2 0x00000100
+#define AR5K_MIC_QOS_SEL_3 0x00001000
+#define AR5K_MIC_QOS_SEL_4 0x00010000
+#define AR5K_MIC_QOS_SEL_5 0x00100000
+#define AR5K_MIC_QOS_SEL_6 0x01000000
+#define AR5K_MIC_QOS_SEL_7 0x10000000
+
+/*
+ * Misc mode control register (?)
+ */
+#define AR5K_MISC_MODE 0x8120 /* Register Address */
+#define AR5K_MISC_MODE_FBSSID_MATCH 0x00000001 /* Force BSSID match */
+#define AR5K_MISC_MODE_ACKSIFS_MEM 0x00000002 /* ACK SIFS memory (?) */
+/* more bits */
+
+/*
+ * OFDM Filter counter
+ */
+#define AR5K_OFDM_FIL_CNT 0x8124
+
+/*
+ * CCK Filter counter
+ */
+#define AR5K_CCK_FIL_CNT 0x8128
+
+/*
+ * PHY Error Counters (?)
+ */
+#define AR5K_PHYERR_CNT1 0x812c
+#define AR5K_PHYERR_CNT1_MASK 0x8130
+
+#define AR5K_PHYERR_CNT2 0x8134
+#define AR5K_PHYERR_CNT2_MASK 0x8138
+
+/*
+ * TSF Threshold register (?)
+ */
+#define AR5K_TSF_THRES 0x813c
+
+/*
+ * Rate -> ACK SIFS mapping table (32 entries)
+ */
+#define AR5K_RATE_ACKSIFS_BASE 0x8680 /* Register Address */
+#define AR5K_RATE_ACKSIFS(_n) (AR5K_RATE_ACKSIFS_BSE + ((_n) << 2))
+#define AR5K_RATE_ACKSIFS_NORMAL 0x00000001 /* Normal SIFS (field) */
+#define AR5K_RATE_ACKSIFS_TURBO 0x00000400 /* Turbo SIFS (field) */
+
+/*
+ * Rate -> duration mapping table (32 entries)
*/
#define AR5K_RATE_DUR_BASE 0x8700
#define AR5K_RATE_DUR(_n) (AR5K_RATE_DUR_BASE + ((_n) << 2))
+/*
+ * Rate -> db mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_RATE2DB_BASE 0x87c0
+#define AR5K_RATE2DB(_n) (AR5K_RATE2DB_BASE + ((_n) << 2))
+
+/*
+ * db -> Rate mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_DB2RATE_BASE 0x87e0
+#define AR5K_DB2RATE(_n) (AR5K_DB2RATE_BASE + ((_n) << 2))
+
/*===5212 end===*/
/*
/*===PHY REGISTERS===*/
/*
- * PHY register
+ * PHY registers start
*/
#define AR5K_PHY_BASE 0x9800
#define AR5K_PHY(_n) (AR5K_PHY_BASE + ((_n) << 2))
-#define AR5K_PHY_SHIFT_2GHZ 0x00004007
-#define AR5K_PHY_SHIFT_5GHZ 0x00000007
+
+/*
+ * TST_2 (Misc config parameters)
+ */
+#define AR5K_PHY_TST2 0x9800 /* Register Address */
+#define AR5K_PHY_TST2_TRIG_SEL 0x00000001 /* Trigger select (?) (field ?) */
+#define AR5K_PHY_TST2_TRIG 0x00000010 /* Trigger (?) (field ?) */
+#define AR5K_PHY_TST2_CBUS_MODE 0x00000100 /* Cardbus mode (?) */
+/* bit reserved */
+#define AR5K_PHY_TST2_CLK32 0x00000400 /* CLK_OUT is CLK32 (32Khz external) */
+#define AR5K_PHY_TST2_CHANCOR_DUMP_EN 0x00000800 /* Enable Chancor dump (?) */
+#define AR5K_PHY_TST2_EVEN_CHANCOR_DUMP 0x00001000 /* Even Chancor dump (?) */
+#define AR5K_PHY_TST2_RFSILENT_EN 0x00002000 /* Enable RFSILENT */
+#define AR5K_PHY_TST2_ALT_RFDATA 0x00004000 /* Alternate RFDATA (5-2GHz switch) */
+#define AR5K_PHY_TST2_MINI_OBS_EN 0x00008000 /* Enable mini OBS (?) */
+#define AR5K_PHY_TST2_RX2_IS_RX5_INV 0x00010000 /* 2GHz rx path is the 5GHz path inverted (?) */
+#define AR5K_PHY_TST2_SLOW_CLK160 0x00020000 /* Slow CLK160 (?) */
+#define AR5K_PHY_TST2_AGC_OBS_SEL_3 0x00040000 /* AGC OBS Select 3 (?) */
+#define AR5K_PHY_TST2_BBB_OBS_SEL 0x00080000 /* BB OBS Select (field ?) */
+#define AR5K_PHY_TST2_ADC_OBS_SEL 0x00800000 /* ADC OBS Select (field ?) */
+#define AR5K_PHY_TST2_RX_CLR_SEL 0x08000000 /* RX Clear Select (?) */
+#define AR5K_PHY_TST2_FORCE_AGC_CLR 0x10000000 /* Force AGC clear (?) */
+#define AR5K_PHY_SHIFT_2GHZ 0x00004007 /* Used to access 2GHz radios */
+#define AR5K_PHY_SHIFT_5GHZ 0x00000007 /* Used to access 5GHz radios (default) */
/*
* PHY frame control register [5110] /turbo mode register [5111+]
* a "turbo mode register" for 5110. We treat this one as
* a frame control register for 5110 below.
*/
-#define AR5K_PHY_TURBO 0x9804
-#define AR5K_PHY_TURBO_MODE 0x00000001
-#define AR5K_PHY_TURBO_SHORT 0x00000002
+#define AR5K_PHY_TURBO 0x9804 /* Register Address */
+#define AR5K_PHY_TURBO_MODE 0x00000001 /* Enable turbo mode */
+#define AR5K_PHY_TURBO_SHORT 0x00000002 /* Short mode (20Mhz channels) (?) */
/*
* PHY agility command register
+ * (aka TST_1)
*/
-#define AR5K_PHY_AGC 0x9808
-#define AR5K_PHY_AGC_DISABLE 0x08000000
+#define AR5K_PHY_AGC 0x9808 /* Register Address */
+#define AR5K_PHY_TST1 0x9808
+#define AR5K_PHY_AGC_DISABLE 0x08000000 /* Disable AGC to A2 (?)*/
+#define AR5K_PHY_TST1_TXHOLD 0x00003800 /* Set tx hold (?) */
/*
- * PHY timing register [5112+]
+ * PHY timing register 3 [5112+]
*/
#define AR5K_PHY_TIMING_3 0x9814
#define AR5K_PHY_TIMING_3_DSC_MAN 0xfffe0000
/*
* PHY activation register
*/
-#define AR5K_PHY_ACT 0x981c
-#define AR5K_PHY_ACT_ENABLE 0x00000001
-#define AR5K_PHY_ACT_DISABLE 0x00000002
+#define AR5K_PHY_ACT 0x981c /* Register Address */
+#define AR5K_PHY_ACT_ENABLE 0x00000001 /* Activate PHY */
+#define AR5K_PHY_ACT_DISABLE 0x00000002 /* Deactivate PHY */
+
+/*
+ * PHY RF control registers
+ * (i think these are delay times,
+ * these calibration values exist
+ * in EEPROM)
+ */
+#define AR5K_PHY_RF_CTL2 0x9824 /* Register Address */
+#define AR5K_PHY_RF_CTL2_TXF2TXD_START 0x0000000f /* Mask for TX frame to TX d(esc?) start */
+
+#define AR5K_PHY_RF_CTL3 0x9828 /* Register Address */
+#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON 0x0000000f /* Mask for TX end to XLNA on */
+
+#define AR5K_PHY_RF_CTL4 0x9834 /* Register Address */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_A_ON 0x00000001 /* TX frame to XPA A on (field) */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_B_ON 0x00000100 /* TX frame to XPA B on (field) */
+#define AR5K_PHY_RF_CTL4_TXE2XPA_A_OFF 0x00010000 /* TX end to XPA A off (field) */
+#define AR5K_PHY_RF_CTL4_TXE2XPA_B_OFF 0x01000000 /* TX end to XPA B off (field) */
+
+/*
+ * Pre-Amplifier control register
+ * (XPA -> external pre-amplifier)
+ */
+#define AR5K_PHY_PA_CTL 0x9838 /* Register Address */
+#define AR5K_PHY_PA_CTL_XPA_A_HI 0x00000001 /* XPA A high (?) */
+#define AR5K_PHY_PA_CTL_XPA_B_HI 0x00000002 /* XPA B high (?) */
+#define AR5K_PHY_PA_CTL_XPA_A_EN 0x00000004 /* Enable XPA A */
+#define AR5K_PHY_PA_CTL_XPA_B_EN 0x00000008 /* Enable XPA B */
+
+/*
+ * PHY settling register
+ */
+#define AR5K_PHY_SETTLING 0x9844 /* Register Address */
+#define AR5K_PHY_SETTLING_AGC 0x0000007f /* Mask for AGC settling time */
+#define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Mask for Switch settlig time */
+
+/*
+ * PHY Gain registers
+ */
+#define AR5K_PHY_GAIN 0x9848 /* Register Address */
+#define AR5K_PHY_GAIN_TXRX_ATTEN 0x0003f000 /* Mask for TX-RX Attenuation */
+
+#define AR5K_PHY_GAIN_OFFSET 0x984c /* Register Address */
+#define AR5K_PHY_GAIN_OFFSET_RXTX_FLAG 0x00020000 /* RX-TX flag (?) */
+
+/*
+ * Desired size register
+ * (for more infos read ANI patent)
+ */
+#define AR5K_PHY_DESIRED_SIZE 0x9850 /* Register Address */
+#define AR5K_PHY_DESIRED_SIZE_ADC 0x000000ff /* Mask for ADC desired size */
+#define AR5K_PHY_DESIRED_SIZE_PGA 0x0000ff00 /* Mask for PGA desired size */
+#define AR5K_PHY_DESIRED_SIZE_TOT 0x0ff00000 /* Mask for Total desired size (?) */
/*
* PHY signal register
+ * (for more infos read ANI patent)
*/
-#define AR5K_PHY_SIG 0x9858
-#define AR5K_PHY_SIG_FIRSTEP 0x0003f000
+#define AR5K_PHY_SIG 0x9858 /* Register Address */
+#define AR5K_PHY_SIG_FIRSTEP 0x0003f000 /* Mask for FIRSTEP */
#define AR5K_PHY_SIG_FIRSTEP_S 12
-#define AR5K_PHY_SIG_FIRPWR 0x03fc0000
+#define AR5K_PHY_SIG_FIRPWR 0x03fc0000 /* Mask for FIPWR */
#define AR5K_PHY_SIG_FIRPWR_S 18
/*
* PHY coarse agility control register
+ * (for more infos read ANI patent)
*/
-#define AR5K_PHY_AGCCOARSE 0x985c
-#define AR5K_PHY_AGCCOARSE_LO 0x00007f80
+#define AR5K_PHY_AGCCOARSE 0x985c /* Register Address */
+#define AR5K_PHY_AGCCOARSE_LO 0x00007f80 /* Mask for AGC Coarse low */
#define AR5K_PHY_AGCCOARSE_LO_S 7
-#define AR5K_PHY_AGCCOARSE_HI 0x003f8000
+#define AR5K_PHY_AGCCOARSE_HI 0x003f8000 /* Mask for AGC Coarse high */
#define AR5K_PHY_AGCCOARSE_HI_S 15
/*
/*
* PHY noise floor status register
*/
-#define AR5K_PHY_NF 0x9864
-#define AR5K_PHY_NF_M 0x000001ff
-#define AR5K_PHY_NF_ACTIVE 0x00000100
+#define AR5K_PHY_NF 0x9864 /* Register address */
+#define AR5K_PHY_NF_M 0x000001ff /* Noise floor mask */
+#define AR5K_PHY_NF_ACTIVE 0x00000100 /* Noise floor calibration still active */
#define AR5K_PHY_NF_RVAL(_n) (((_n) >> 19) & AR5K_PHY_NF_M)
#define AR5K_PHY_NF_AVAL(_n) (-((_n) ^ AR5K_PHY_NF_M) + 1)
#define AR5K_PHY_NF_SVAL(_n) (((_n) & AR5K_PHY_NF_M) | (1 << 9))
+#define AR5K_PHY_NF_THRESH62 0x00001000 /* Thresh62 -check ANI patent- (field) */
/*
* PHY ADC saturation register [5110]
#define AR5K_PHY_ADCSAT_THR 0x000007e0
#define AR5K_PHY_ADCSAT_THR_S 5
+/*
+ * PHY Weak ofdm signal detection threshold registers (ANI) [5212+]
+ */
+
+/* High thresholds */
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR 0x9868
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT 0x0000001f
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT_S 0
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1 0x00fe0000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1_S 17
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2 0x7f000000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_S 24
+
+/* Low thresholds */
+#define AR5K_PHY_WEAK_OFDM_LOW_THR 0x986c
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN 0x00000001
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT 0x00003f00
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT_S 8
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1 0x001fc000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1_S 14
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2 0x0fe00000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_S 21
+
+
/*
* PHY sleep registers [5112+]
*/
AR5K_PHY_PLL_44MHZ_5211 : AR5K_PHY_PLL_44MHZ_5212)
#define AR5K_PHY_PLL_RF5111 0x00000000
#define AR5K_PHY_PLL_RF5112 0x00000040
+#define AR5K_PHY_PLL_HALF_RATE 0x00000100
+#define AR5K_PHY_PLL_QUARTER_RATE 0x00000200
/*
* RF Buffer register
#define AR5K_PHY_RFSTG 0x98d4
#define AR5K_PHY_RFSTG_DISABLE 0x00000021
+/*
+ * PHY Antenna control register
+ */
+#define AR5K_PHY_ANT_CTL 0x9910 /* Register Address */
+#define AR5K_PHY_ANT_CTL_TXRX_EN 0x00000001 /* Enable TX/RX (?) */
+#define AR5K_PHY_ANT_CTL_SECTORED_ANT 0x00000004 /* Sectored Antenna */
+#define AR5K_PHY_ANT_CTL_HITUNE5 0x00000008 /* Hitune5 (?) */
+#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE 0x00000010 /* Switch table idle (?) */
+
/*
* PHY receiver delay register [5111+]
*/
-#define AR5K_PHY_RX_DELAY 0x9914
-#define AR5K_PHY_RX_DELAY_M 0x00003fff
+#define AR5K_PHY_RX_DELAY 0x9914 /* Register Address */
+#define AR5K_PHY_RX_DELAY_M 0x00003fff /* Mask for RX activate to receive delay (/100ns) */
+
+/*
+ * PHY max rx length register (?) [5111]
+ */
+#define AR5K_PHY_MAX_RX_LEN 0x991c
/*
- * PHY timing I(nphase) Q(adrature) control register [5111+]
+ * PHY timing register 4
+ * I(nphase)/Q(adrature) calibration register [5111+]
*/
-#define AR5K_PHY_IQ 0x9920 /* Register address */
+#define AR5K_PHY_IQ 0x9920 /* Register Address */
#define AR5K_PHY_IQ_CORR_Q_Q_COFF 0x0000001f /* Mask for q correction info */
#define AR5K_PHY_IQ_CORR_Q_I_COFF 0x000007e0 /* Mask for i correction info */
#define AR5K_PHY_IQ_CORR_Q_I_COFF_S 5
#define AR5K_PHY_IQ_CORR_ENABLE 0x00000800 /* Enable i/q correction */
-#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000
+#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX 0x0000f000 /* Mask for max number of samples in log scale */
#define AR5K_PHY_IQ_CAL_NUM_LOG_MAX_S 12
#define AR5K_PHY_IQ_RUN 0x00010000 /* Run i/q calibration */
+#define AR5K_PHY_IQ_USE_PT_DF 0x00020000 /* Use pilot track df (?) */
+#define AR5K_PHY_IQ_EARLY_TRIG_THR 0x00200000 /* Early trigger threshold (?) (field) */
+#define AR5K_PHY_IQ_PILOT_MASK_EN 0x10000000 /* Enable pilot mask (?) */
+#define AR5K_PHY_IQ_CHAN_MASK_EN 0x20000000 /* Enable channel mask (?) */
+#define AR5K_PHY_IQ_SPUR_FILT_EN 0x40000000 /* Enable spur filter */
+#define AR5K_PHY_IQ_SPUR_RSSI_EN 0x80000000 /* Enable spur rssi */
+/*
+ * PHY timing register 5
+ * OFDM Self-correlator Cyclic RSSI threshold params
+ * (Check out bb_cycpwr_thr1 on ANI patent)
+ */
+#define AR5K_PHY_OFDM_SELFCORR 0x9924 /* Register Address */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_EN 0x00000001 /* Enable cyclic RSSI thr 1 */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1 0x000000fe /* Mask for Cyclic RSSI threshold 1 */
+#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR3 0x00000100 /* Cyclic RSSI threshold 3 (field) (?) */
+#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR_EN 0x00008000 /* Enable 1A RSSI threshold (?) */
+#define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR 0x00010000 /* 1A RSSI threshold (field) (?) */
+#define AR5K_PHY_OFDM_SELFCORR_LSCTHR_HIRSSI 0x00800000 /* Long sc threshold hi rssi (?) */
+
+/*
+ * PHY-only warm reset register
+ */
+#define AR5K_PHY_WARM_RESET 0x9928
+
+/*
+ * PHY-only control register
+ */
+#define AR5K_PHY_CTL 0x992c /* Register Address */
+#define AR5K_PHY_CTL_RX_DRAIN_RATE 0x00000001 /* RX drain rate (?) */
+#define AR5K_PHY_CTL_LATE_TX_SIG_SYM 0x00000002 /* Late tx signal symbol (?) */
+#define AR5K_PHY_CTL_GEN_SCRAMBLER 0x00000004 /* Generate scrambler */
+#define AR5K_PHY_CTL_TX_ANT_SEL 0x00000008 /* TX antenna select */
+#define AR5K_PHY_CTL_TX_ANT_STATIC 0x00000010 /* Static TX antenna */
+#define AR5K_PHY_CTL_RX_ANT_SEL 0x00000020 /* RX antenna select */
+#define AR5K_PHY_CTL_RX_ANT_STATIC 0x00000040 /* Static RX antenna */
+#define AR5K_PHY_CTL_LOW_FREQ_SLE_EN 0x00000080 /* Enable low freq sleep */
/*
* PHY PAPD probe register [5111+ (?)]
* Because it's always 0 in 5211 initialization code
*/
#define AR5K_PHY_PAPD_PROBE 0x9930
+#define AR5K_PHY_PAPD_PROBE_SH_HI_PAR 0x00000001
+#define AR5K_PHY_PAPD_PROBE_PCDAC_BIAS 0x00000002
+#define AR5K_PHY_PAPD_PROBE_COMP_GAIN 0x00000040
#define AR5K_PHY_PAPD_PROBE_TXPOWER 0x00007e00
#define AR5K_PHY_PAPD_PROBE_TXPOWER_S 9
#define AR5K_PHY_PAPD_PROBE_TX_NEXT 0x00008000
+#define AR5K_PHY_PAPD_PROBE_PREDIST_EN 0x00010000
#define AR5K_PHY_PAPD_PROBE_TYPE 0x01800000 /* [5112+] */
#define AR5K_PHY_PAPD_PROBE_TYPE_S 23
#define AR5K_PHY_PAPD_PROBE_TYPE_OFDM 0
#define AR5K_PHY_FRAME_CTL (ah->ah_version == AR5K_AR5210 ? \
AR5K_PHY_FRAME_CTL_5210 : AR5K_PHY_FRAME_CTL_5211)
/*---[5111+]---*/
-#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038
+#define AR5K_PHY_FRAME_CTL_TX_CLIP 0x00000038 /* Mask for tx clip (?) */
#define AR5K_PHY_FRAME_CTL_TX_CLIP_S 3
+#define AR5K_PHY_FRAME_CTL_PREP_CHINFO 0x00010000 /* Prepend chan info */
/*---[5110/5111]---*/
-#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000
-#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000
-#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* illegal rate */
-#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* illegal length */
+#define AR5K_PHY_FRAME_CTL_TIMING_ERR 0x01000000 /* PHY timing error */
+#define AR5K_PHY_FRAME_CTL_PARITY_ERR 0x02000000 /* Parity error */
+#define AR5K_PHY_FRAME_CTL_ILLRATE_ERR 0x04000000 /* Illegal rate */
+#define AR5K_PHY_FRAME_CTL_ILLLEN_ERR 0x08000000 /* Illegal length */
#define AR5K_PHY_FRAME_CTL_SERVICE_ERR 0x20000000
-#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* tx underrun */
+#define AR5K_PHY_FRAME_CTL_TXURN_ERR 0x40000000 /* TX underrun */
#define AR5K_PHY_FRAME_CTL_INI AR5K_PHY_FRAME_CTL_SERVICE_ERR | \
AR5K_PHY_FRAME_CTL_TXURN_ERR | \
AR5K_PHY_FRAME_CTL_ILLLEN_ERR | \
#define AR5K_PHY_ANT_SWITCH_TABLE_0 0x9960
#define AR5K_PHY_ANT_SWITCH_TABLE_1 0x9964
+/*
+ * PHY Noise floor threshold
+ */
+#define AR5K_PHY_NFTHRES 0x9968
+
/*
* PHY clock sleep registers [5112+]
*/
#define AR5K_PHY_SDELAY 0x99f4
#define AR5K_PHY_SDELAY_32MHZ 0x000000ff
#define AR5K_PHY_SPENDING 0x99f8
+#define AR5K_PHY_SPENDING_14 0x00000014
+#define AR5K_PHY_SPENDING_18 0x00000018
#define AR5K_PHY_SPENDING_RF5111 0x00000018
-#define AR5K_PHY_SPENDING_RF5112 0x00000014 /* <- i 've only seen this on 2425 dumps ! */
-#define AR5K_PHY_SPENDING_RF5112A 0x0000000e /* but since i only have 5112A-based chips */
-#define AR5K_PHY_SPENDING_RF5424 0x00000012 /* to test it might be also for old 5112. */
+#define AR5K_PHY_SPENDING_RF5112 0x00000014
+/* #define AR5K_PHY_SPENDING_RF5112A 0x0000000e */
+/* #define AR5K_PHY_SPENDING_RF5424 0x00000012 */
+#define AR5K_PHY_SPENDING_RF5413 0x00000014
+#define AR5K_PHY_SPENDING_RF2413 0x00000014
+#define AR5K_PHY_SPENDING_RF2425 0x00000018
/*
* Misc PHY/radio registers [5110 - 5111]
*/
-#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */
+#define AR5K_BB_GAIN_BASE 0x9b00 /* BaseBand Amplifier Gain table base address */
#define AR5K_BB_GAIN(_n) (AR5K_BB_GAIN_BASE + ((_n) << 2))
-#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */
+#define AR5K_RF_GAIN_BASE 0x9a00 /* RF Amplrifier Gain table base address */
#define AR5K_RF_GAIN(_n) (AR5K_RF_GAIN_BASE + ((_n) << 2))
/*
* PHY timing IQ calibration result register [5111+]
*/
-#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */
-#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */
+#define AR5K_PHY_IQRES_CAL_PWR_I 0x9c10 /* I (Inphase) power value */
+#define AR5K_PHY_IQRES_CAL_PWR_Q 0x9c14 /* Q (Quadrature) power value */
#define AR5K_PHY_IQRES_CAL_CORR 0x9c18 /* I/Q Correlation */
/*
* PHY current RSSI register [5111+]
*/
-#define AR5K_PHY_CURRENT_RSSI 0x9c1c
+#define AR5K_PHY_CURRENT_RSSI 0x9c1c
+
+/*
+ * PHY RF Bus grant register (?)
+ */
+#define AR5K_PHY_RFBUS_GRANT 0x9c20
+
+/*
+ * PHY ADC test register
+ */
+#define AR5K_PHY_ADC_TEST 0x9c24
+#define AR5K_PHY_ADC_TEST_I 0x00000001
+#define AR5K_PHY_ADC_TEST_Q 0x00000200
+
+/*
+ * PHY DAC test register
+ */
+#define AR5K_PHY_DAC_TEST 0x9c28
+#define AR5K_PHY_DAC_TEST_I 0x00000001
+#define AR5K_PHY_DAC_TEST_Q 0x00000200
+
+/*
+ * PHY PTAT register (?)
+ */
+#define AR5K_PHY_PTAT 0x9c2c
+
+/*
+ * PHY Illegal TX rate register [5112+]
+ */
+#define AR5K_PHY_BAD_TX_RATE 0x9c30
+
+/*
+ * PHY SPUR Power register [5112+]
+ */
+#define AR5K_PHY_SPUR_PWR 0x9c34 /* Register Address */
+#define AR5K_PHY_SPUR_PWR_I 0x00000001 /* SPUR Power estimate for I (field) */
+#define AR5K_PHY_SPUR_PWR_Q 0x00000100 /* SPUR Power estimate for Q (field) */
+#define AR5K_PHY_SPUR_PWR_FILT 0x00010000 /* Power with SPUR removed (field) */
+
+/*
+ * PHY Channel status register [5112+] (?)
+ */
+#define AR5K_PHY_CHAN_STATUS 0x9c38
+#define AR5K_PHY_CHAN_STATUS_BT_ACT 0x00000001
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_RAW 0x00000002
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_MAC 0x00000004
+#define AR5K_PHY_CHAN_STATUS_RX_CLR_PAP 0x00000008
+
+/*
+ * PHY PAPD I (power?) table (?)
+ * (92! entries)
+ */
+#define AR5K_PHY_PAPD_I_BASE 0xa000
+#define AR5K_PHY_PAPD_I(_n) (AR5K_PHY_PAPD_I_BASE + ((_n) << 2))
/*
* PHY PCDAC TX power table
*/
#define AR5K_PHY_PCDAC_TXPOWER_BASE_5211 0xa180
-#define AR5K_PHY_PCDAC_TXPOWER_BASE_5413 0xa280
-#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF5413 ? \
- AR5K_PHY_PCDAC_TXPOWER_BASE_5413 :\
+#define AR5K_PHY_PCDAC_TXPOWER_BASE_2413 0xa280
+#define AR5K_PHY_PCDAC_TXPOWER_BASE (ah->ah_radio >= AR5K_RF2413 ? \
+ AR5K_PHY_PCDAC_TXPOWER_BASE_2413 :\
AR5K_PHY_PCDAC_TXPOWER_BASE_5211)
#define AR5K_PHY_PCDAC_TXPOWER(_n) (AR5K_PHY_PCDAC_TXPOWER_BASE + ((_n) << 2))
/*
* PHY mode register [5111+]
*/
-#define AR5K_PHY_MODE 0x0a200 /* Register address */
-#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation mask*/
+#define AR5K_PHY_MODE 0x0a200 /* Register Address */
+#define AR5K_PHY_MODE_MOD 0x00000001 /* PHY Modulation bit */
#define AR5K_PHY_MODE_MOD_OFDM 0
#define AR5K_PHY_MODE_MOD_CCK 1
-#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode mask */
+#define AR5K_PHY_MODE_FREQ 0x00000002 /* Freq mode bit */
#define AR5K_PHY_MODE_FREQ_5GHZ 0
#define AR5K_PHY_MODE_FREQ_2GHZ 2
-#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Dynamic OFDM/CCK mode mask [5112+] */
+#define AR5K_PHY_MODE_MOD_DYN 0x00000004 /* Enable Dynamic OFDM/CCK mode [5112+] */
#define AR5K_PHY_MODE_RAD 0x00000008 /* [5212+] */
#define AR5K_PHY_MODE_RAD_RF5111 0
#define AR5K_PHY_MODE_RAD_RF5112 8
-#define AR5K_PHY_MODE_XR 0x00000010 /* [5112+] */
+#define AR5K_PHY_MODE_XR 0x00000010 /* Enable XR mode [5112+] */
+#define AR5K_PHY_MODE_HALF_RATE 0x00000020 /* Enable Half rate (test) */
+#define AR5K_PHY_MODE_QUARTER_RATE 0x00000040 /* Enable Quarter rat (test) */
/*
* PHY CCK transmit control register [5111+ (?)]
#define AR5K_PHY_CCKTXCTL 0xa204
#define AR5K_PHY_CCKTXCTL_WORLD 0x00000000
#define AR5K_PHY_CCKTXCTL_JAPAN 0x00000010
+#define AR5K_PHY_CCKTXCTL_SCRAMBLER_DIS 0x00000001
+#define AR5K_PHY_CCKTXCTK_DAC_SCALE 0x00000004
+
+/*
+ * PHY CCK Cross-correlator Barker RSSI threshold register [5212+]
+ */
+#define AR5K_PHY_CCK_CROSSCORR 0xa208
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR 0x0000000f
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR_S 0
/*
* PHY 2GHz gain register [5111+]
--- /dev/null
+config ATH9K
+ tristate "Atheros 802.11n wireless cards support"
+ depends on PCI && MAC80211 && WLAN_80211
+ ---help---
+ This module adds support for wireless adapters based on
+ Atheros IEEE 802.11n AR5008 and AR9001 family of chipsets.
+
+ If you choose to build a module, it'll be called ath9k.
--- /dev/null
+ath9k-y += hw.o \
+ phy.o \
+ regd.o \
+ beacon.o \
+ main.o \
+ recv.o \
+ xmit.o \
+ rc.o \
+ core.o
+
+obj-$(CONFIG_ATH9K) += ath9k.o
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef ATH9K_H
+#define ATH9K_H
+
+#include <linux/io.h>
+
+#define ATHEROS_VENDOR_ID 0x168c
+
+#define AR5416_DEVID_PCI 0x0023
+#define AR5416_DEVID_PCIE 0x0024
+#define AR9160_DEVID_PCI 0x0027
+#define AR9280_DEVID_PCI 0x0029
+#define AR9280_DEVID_PCIE 0x002a
+
+#define AR5416_AR9100_DEVID 0x000b
+
+#define AR_SUBVENDOR_ID_NOG 0x0e11
+#define AR_SUBVENDOR_ID_NEW_A 0x7065
+
+#define ATH9K_TXERR_XRETRY 0x01
+#define ATH9K_TXERR_FILT 0x02
+#define ATH9K_TXERR_FIFO 0x04
+#define ATH9K_TXERR_XTXOP 0x08
+#define ATH9K_TXERR_TIMER_EXPIRED 0x10
+
+#define ATH9K_TX_BA 0x01
+#define ATH9K_TX_PWRMGMT 0x02
+#define ATH9K_TX_DESC_CFG_ERR 0x04
+#define ATH9K_TX_DATA_UNDERRUN 0x08
+#define ATH9K_TX_DELIM_UNDERRUN 0x10
+#define ATH9K_TX_SW_ABORTED 0x40
+#define ATH9K_TX_SW_FILTERED 0x80
+
+#define NBBY 8
+
+struct ath_tx_status {
+ u32 ts_tstamp;
+ u16 ts_seqnum;
+ u8 ts_status;
+ u8 ts_ratecode;
+ u8 ts_rateindex;
+ int8_t ts_rssi;
+ u8 ts_shortretry;
+ u8 ts_longretry;
+ u8 ts_virtcol;
+ u8 ts_antenna;
+ u8 ts_flags;
+ int8_t ts_rssi_ctl0;
+ int8_t ts_rssi_ctl1;
+ int8_t ts_rssi_ctl2;
+ int8_t ts_rssi_ext0;
+ int8_t ts_rssi_ext1;
+ int8_t ts_rssi_ext2;
+ u8 pad[3];
+ u32 ba_low;
+ u32 ba_high;
+ u32 evm0;
+ u32 evm1;
+ u32 evm2;
+};
+
+struct ath_rx_status {
+ u32 rs_tstamp;
+ u16 rs_datalen;
+ u8 rs_status;
+ u8 rs_phyerr;
+ int8_t rs_rssi;
+ u8 rs_keyix;
+ u8 rs_rate;
+ u8 rs_antenna;
+ u8 rs_more;
+ int8_t rs_rssi_ctl0;
+ int8_t rs_rssi_ctl1;
+ int8_t rs_rssi_ctl2;
+ int8_t rs_rssi_ext0;
+ int8_t rs_rssi_ext1;
+ int8_t rs_rssi_ext2;
+ u8 rs_isaggr;
+ u8 rs_moreaggr;
+ u8 rs_num_delims;
+ u8 rs_flags;
+ u32 evm0;
+ u32 evm1;
+ u32 evm2;
+};
+
+#define ATH9K_RXERR_CRC 0x01
+#define ATH9K_RXERR_PHY 0x02
+#define ATH9K_RXERR_FIFO 0x04
+#define ATH9K_RXERR_DECRYPT 0x08
+#define ATH9K_RXERR_MIC 0x10
+
+#define ATH9K_RX_MORE 0x01
+#define ATH9K_RX_MORE_AGGR 0x02
+#define ATH9K_RX_GI 0x04
+#define ATH9K_RX_2040 0x08
+#define ATH9K_RX_DELIM_CRC_PRE 0x10
+#define ATH9K_RX_DELIM_CRC_POST 0x20
+#define ATH9K_RX_DECRYPT_BUSY 0x40
+
+#define ATH9K_RXKEYIX_INVALID ((u8)-1)
+#define ATH9K_TXKEYIX_INVALID ((u32)-1)
+
+struct ath_desc {
+ u32 ds_link;
+ u32 ds_data;
+ u32 ds_ctl0;
+ u32 ds_ctl1;
+ u32 ds_hw[20];
+ union {
+ struct ath_tx_status tx;
+ struct ath_rx_status rx;
+ void *stats;
+ } ds_us;
+ void *ds_vdata;
+} __packed;
+
+#define ds_txstat ds_us.tx
+#define ds_rxstat ds_us.rx
+#define ds_stat ds_us.stats
+
+#define ATH9K_TXDESC_CLRDMASK 0x0001
+#define ATH9K_TXDESC_NOACK 0x0002
+#define ATH9K_TXDESC_RTSENA 0x0004
+#define ATH9K_TXDESC_CTSENA 0x0008
+#define ATH9K_TXDESC_INTREQ 0x0010
+#define ATH9K_TXDESC_VEOL 0x0020
+#define ATH9K_TXDESC_EXT_ONLY 0x0040
+#define ATH9K_TXDESC_EXT_AND_CTL 0x0080
+#define ATH9K_TXDESC_VMF 0x0100
+#define ATH9K_TXDESC_FRAG_IS_ON 0x0200
+
+#define ATH9K_RXDESC_INTREQ 0x0020
+
+enum wireless_mode {
+ ATH9K_MODE_11A = 0,
+ ATH9K_MODE_11B = 2,
+ ATH9K_MODE_11G = 3,
+ ATH9K_MODE_11NA_HT20 = 6,
+ ATH9K_MODE_11NG_HT20 = 7,
+ ATH9K_MODE_11NA_HT40PLUS = 8,
+ ATH9K_MODE_11NA_HT40MINUS = 9,
+ ATH9K_MODE_11NG_HT40PLUS = 10,
+ ATH9K_MODE_11NG_HT40MINUS = 11,
+ ATH9K_MODE_MAX
+};
+
+enum ath9k_hw_caps {
+ ATH9K_HW_CAP_CHAN_SPREAD = BIT(0),
+ ATH9K_HW_CAP_MIC_AESCCM = BIT(1),
+ ATH9K_HW_CAP_MIC_CKIP = BIT(2),
+ ATH9K_HW_CAP_MIC_TKIP = BIT(3),
+ ATH9K_HW_CAP_CIPHER_AESCCM = BIT(4),
+ ATH9K_HW_CAP_CIPHER_CKIP = BIT(5),
+ ATH9K_HW_CAP_CIPHER_TKIP = BIT(6),
+ ATH9K_HW_CAP_VEOL = BIT(7),
+ ATH9K_HW_CAP_BSSIDMASK = BIT(8),
+ ATH9K_HW_CAP_MCAST_KEYSEARCH = BIT(9),
+ ATH9K_HW_CAP_CHAN_HALFRATE = BIT(10),
+ ATH9K_HW_CAP_CHAN_QUARTERRATE = BIT(11),
+ ATH9K_HW_CAP_HT = BIT(12),
+ ATH9K_HW_CAP_GTT = BIT(13),
+ ATH9K_HW_CAP_FASTCC = BIT(14),
+ ATH9K_HW_CAP_RFSILENT = BIT(15),
+ ATH9K_HW_CAP_WOW = BIT(16),
+ ATH9K_HW_CAP_CST = BIT(17),
+ ATH9K_HW_CAP_ENHANCEDPM = BIT(18),
+ ATH9K_HW_CAP_AUTOSLEEP = BIT(19),
+ ATH9K_HW_CAP_4KB_SPLITTRANS = BIT(20),
+ ATH9K_HW_CAP_WOW_MATCHPATTERN_EXACT = BIT(21),
+};
+
+enum ath9k_capability_type {
+ ATH9K_CAP_CIPHER = 0,
+ ATH9K_CAP_TKIP_MIC,
+ ATH9K_CAP_TKIP_SPLIT,
+ ATH9K_CAP_PHYCOUNTERS,
+ ATH9K_CAP_DIVERSITY,
+ ATH9K_CAP_TXPOW,
+ ATH9K_CAP_PHYDIAG,
+ ATH9K_CAP_MCAST_KEYSRCH,
+ ATH9K_CAP_TSF_ADJUST,
+ ATH9K_CAP_WME_TKIPMIC,
+ ATH9K_CAP_RFSILENT,
+ ATH9K_CAP_ANT_CFG_2GHZ,
+ ATH9K_CAP_ANT_CFG_5GHZ
+};
+
+struct ath9k_hw_capabilities {
+ u32 hw_caps; /* ATH9K_HW_CAP_* from ath9k_hw_caps */
+ DECLARE_BITMAP(wireless_modes, ATH9K_MODE_MAX); /* ATH9K_MODE_* */
+ u16 total_queues;
+ u16 keycache_size;
+ u16 low_5ghz_chan, high_5ghz_chan;
+ u16 low_2ghz_chan, high_2ghz_chan;
+ u16 num_mr_retries;
+ u16 rts_aggr_limit;
+ u8 tx_chainmask;
+ u8 rx_chainmask;
+ u16 tx_triglevel_max;
+ u16 reg_cap;
+ u8 num_gpio_pins;
+ u8 num_antcfg_2ghz;
+ u8 num_antcfg_5ghz;
+};
+
+struct ath9k_ops_config {
+ int dma_beacon_response_time;
+ int sw_beacon_response_time;
+ int additional_swba_backoff;
+ int ack_6mb;
+ int cwm_ignore_extcca;
+ u8 pcie_powersave_enable;
+ u8 pcie_l1skp_enable;
+ u8 pcie_clock_req;
+ u32 pcie_waen;
+ int pcie_power_reset;
+ u8 pcie_restore;
+ u8 analog_shiftreg;
+ u8 ht_enable;
+ u32 ofdm_trig_low;
+ u32 ofdm_trig_high;
+ u32 cck_trig_high;
+ u32 cck_trig_low;
+ u32 enable_ani;
+ u8 noise_immunity_level;
+ u32 ofdm_weaksignal_det;
+ u32 cck_weaksignal_thr;
+ u8 spur_immunity_level;
+ u8 firstep_level;
+ int8_t rssi_thr_high;
+ int8_t rssi_thr_low;
+ u16 diversity_control;
+ u16 antenna_switch_swap;
+ int serialize_regmode;
+ int intr_mitigation;
+#define SPUR_DISABLE 0
+#define SPUR_ENABLE_IOCTL 1
+#define SPUR_ENABLE_EEPROM 2
+#define AR_EEPROM_MODAL_SPURS 5
+#define AR_SPUR_5413_1 1640
+#define AR_SPUR_5413_2 1200
+#define AR_NO_SPUR 0x8000
+#define AR_BASE_FREQ_2GHZ 2300
+#define AR_BASE_FREQ_5GHZ 4900
+#define AR_SPUR_FEEQ_BOUND_HT40 19
+#define AR_SPUR_FEEQ_BOUND_HT20 10
+ int spurmode;
+ u16 spurchans[AR_EEPROM_MODAL_SPURS][2];
+};
+
+enum ath9k_tx_queue {
+ ATH9K_TX_QUEUE_INACTIVE = 0,
+ ATH9K_TX_QUEUE_DATA,
+ ATH9K_TX_QUEUE_BEACON,
+ ATH9K_TX_QUEUE_CAB,
+ ATH9K_TX_QUEUE_UAPSD,
+ ATH9K_TX_QUEUE_PSPOLL
+};
+
+#define ATH9K_NUM_TX_QUEUES 10
+
+enum ath9k_tx_queue_subtype {
+ ATH9K_WME_AC_BK = 0,
+ ATH9K_WME_AC_BE,
+ ATH9K_WME_AC_VI,
+ ATH9K_WME_AC_VO,
+ ATH9K_WME_UPSD
+};
+
+enum ath9k_tx_queue_flags {
+ TXQ_FLAG_TXOKINT_ENABLE = 0x0001,
+ TXQ_FLAG_TXERRINT_ENABLE = 0x0001,
+ TXQ_FLAG_TXDESCINT_ENABLE = 0x0002,
+ TXQ_FLAG_TXEOLINT_ENABLE = 0x0004,
+ TXQ_FLAG_TXURNINT_ENABLE = 0x0008,
+ TXQ_FLAG_BACKOFF_DISABLE = 0x0010,
+ TXQ_FLAG_COMPRESSION_ENABLE = 0x0020,
+ TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE = 0x0040,
+ TXQ_FLAG_FRAG_BURST_BACKOFF_ENABLE = 0x0080,
+};
+
+#define ATH9K_TXQ_USEDEFAULT ((u32) -1)
+
+#define ATH9K_DECOMP_MASK_SIZE 128
+#define ATH9K_READY_TIME_LO_BOUND 50
+#define ATH9K_READY_TIME_HI_BOUND 96
+
+enum ath9k_pkt_type {
+ ATH9K_PKT_TYPE_NORMAL = 0,
+ ATH9K_PKT_TYPE_ATIM,
+ ATH9K_PKT_TYPE_PSPOLL,
+ ATH9K_PKT_TYPE_BEACON,
+ ATH9K_PKT_TYPE_PROBE_RESP,
+ ATH9K_PKT_TYPE_CHIRP,
+ ATH9K_PKT_TYPE_GRP_POLL,
+};
+
+struct ath9k_tx_queue_info {
+ u32 tqi_ver;
+ enum ath9k_tx_queue tqi_type;
+ enum ath9k_tx_queue_subtype tqi_subtype;
+ enum ath9k_tx_queue_flags tqi_qflags;
+ u32 tqi_priority;
+ u32 tqi_aifs;
+ u32 tqi_cwmin;
+ u32 tqi_cwmax;
+ u16 tqi_shretry;
+ u16 tqi_lgretry;
+ u32 tqi_cbrPeriod;
+ u32 tqi_cbrOverflowLimit;
+ u32 tqi_burstTime;
+ u32 tqi_readyTime;
+ u32 tqi_physCompBuf;
+ u32 tqi_intFlags;
+};
+
+enum ath9k_rx_filter {
+ ATH9K_RX_FILTER_UCAST = 0x00000001,
+ ATH9K_RX_FILTER_MCAST = 0x00000002,
+ ATH9K_RX_FILTER_BCAST = 0x00000004,
+ ATH9K_RX_FILTER_CONTROL = 0x00000008,
+ ATH9K_RX_FILTER_BEACON = 0x00000010,
+ ATH9K_RX_FILTER_PROM = 0x00000020,
+ ATH9K_RX_FILTER_PROBEREQ = 0x00000080,
+ ATH9K_RX_FILTER_PSPOLL = 0x00004000,
+ ATH9K_RX_FILTER_PHYERR = 0x00000100,
+ ATH9K_RX_FILTER_PHYRADAR = 0x00002000,
+};
+
+enum ath9k_int {
+ ATH9K_INT_RX = 0x00000001,
+ ATH9K_INT_RXDESC = 0x00000002,
+ ATH9K_INT_RXNOFRM = 0x00000008,
+ ATH9K_INT_RXEOL = 0x00000010,
+ ATH9K_INT_RXORN = 0x00000020,
+ ATH9K_INT_TX = 0x00000040,
+ ATH9K_INT_TXDESC = 0x00000080,
+ ATH9K_INT_TIM_TIMER = 0x00000100,
+ ATH9K_INT_TXURN = 0x00000800,
+ ATH9K_INT_MIB = 0x00001000,
+ ATH9K_INT_RXPHY = 0x00004000,
+ ATH9K_INT_RXKCM = 0x00008000,
+ ATH9K_INT_SWBA = 0x00010000,
+ ATH9K_INT_BMISS = 0x00040000,
+ ATH9K_INT_BNR = 0x00100000,
+ ATH9K_INT_TIM = 0x00200000,
+ ATH9K_INT_DTIM = 0x00400000,
+ ATH9K_INT_DTIMSYNC = 0x00800000,
+ ATH9K_INT_GPIO = 0x01000000,
+ ATH9K_INT_CABEND = 0x02000000,
+ ATH9K_INT_CST = 0x10000000,
+ ATH9K_INT_GTT = 0x20000000,
+ ATH9K_INT_FATAL = 0x40000000,
+ ATH9K_INT_GLOBAL = 0x80000000,
+ ATH9K_INT_BMISC = ATH9K_INT_TIM |
+ ATH9K_INT_DTIM |
+ ATH9K_INT_DTIMSYNC |
+ ATH9K_INT_CABEND,
+ ATH9K_INT_COMMON = ATH9K_INT_RXNOFRM |
+ ATH9K_INT_RXDESC |
+ ATH9K_INT_RXEOL |
+ ATH9K_INT_RXORN |
+ ATH9K_INT_TXURN |
+ ATH9K_INT_TXDESC |
+ ATH9K_INT_MIB |
+ ATH9K_INT_RXPHY |
+ ATH9K_INT_RXKCM |
+ ATH9K_INT_SWBA |
+ ATH9K_INT_BMISS |
+ ATH9K_INT_GPIO,
+ ATH9K_INT_NOCARD = 0xffffffff
+};
+
+struct ath9k_rate_table {
+ int rateCount;
+ u8 rateCodeToIndex[256];
+ struct {
+ u8 valid;
+ u8 phy;
+ u32 rateKbps;
+ u8 rateCode;
+ u8 shortPreamble;
+ u8 dot11Rate;
+ u8 controlRate;
+ u16 lpAckDuration;
+ u16 spAckDuration;
+ } info[32];
+};
+
+#define ATH9K_RATESERIES_RTS_CTS 0x0001
+#define ATH9K_RATESERIES_2040 0x0002
+#define ATH9K_RATESERIES_HALFGI 0x0004
+
+struct ath9k_11n_rate_series {
+ u32 Tries;
+ u32 Rate;
+ u32 PktDuration;
+ u32 ChSel;
+ u32 RateFlags;
+};
+
+#define CHANNEL_CW_INT 0x00002
+#define CHANNEL_CCK 0x00020
+#define CHANNEL_OFDM 0x00040
+#define CHANNEL_2GHZ 0x00080
+#define CHANNEL_5GHZ 0x00100
+#define CHANNEL_PASSIVE 0x00200
+#define CHANNEL_DYN 0x00400
+#define CHANNEL_HALF 0x04000
+#define CHANNEL_QUARTER 0x08000
+#define CHANNEL_HT20 0x10000
+#define CHANNEL_HT40PLUS 0x20000
+#define CHANNEL_HT40MINUS 0x40000
+
+#define CHANNEL_INTERFERENCE 0x01
+#define CHANNEL_DFS 0x02
+#define CHANNEL_4MS_LIMIT 0x04
+#define CHANNEL_DFS_CLEAR 0x08
+#define CHANNEL_DISALLOW_ADHOC 0x10
+#define CHANNEL_PER_11D_ADHOC 0x20
+
+#define CHANNEL_A (CHANNEL_5GHZ|CHANNEL_OFDM)
+#define CHANNEL_B (CHANNEL_2GHZ|CHANNEL_CCK)
+#define CHANNEL_G (CHANNEL_2GHZ|CHANNEL_OFDM)
+#define CHANNEL_G_HT20 (CHANNEL_2GHZ|CHANNEL_HT20)
+#define CHANNEL_A_HT20 (CHANNEL_5GHZ|CHANNEL_HT20)
+#define CHANNEL_G_HT40PLUS (CHANNEL_2GHZ|CHANNEL_HT40PLUS)
+#define CHANNEL_G_HT40MINUS (CHANNEL_2GHZ|CHANNEL_HT40MINUS)
+#define CHANNEL_A_HT40PLUS (CHANNEL_5GHZ|CHANNEL_HT40PLUS)
+#define CHANNEL_A_HT40MINUS (CHANNEL_5GHZ|CHANNEL_HT40MINUS)
+#define CHANNEL_ALL \
+ (CHANNEL_OFDM| \
+ CHANNEL_CCK| \
+ CHANNEL_2GHZ | \
+ CHANNEL_5GHZ | \
+ CHANNEL_HT20 | \
+ CHANNEL_HT40PLUS | \
+ CHANNEL_HT40MINUS)
+
+struct ath9k_channel {
+ u16 channel;
+ u32 channelFlags;
+ u8 privFlags;
+ int8_t maxRegTxPower;
+ int8_t maxTxPower;
+ int8_t minTxPower;
+ u32 chanmode;
+ int32_t CalValid;
+ bool oneTimeCalsDone;
+ int8_t iCoff;
+ int8_t qCoff;
+ int16_t rawNoiseFloor;
+ int8_t antennaMax;
+ u32 regDmnFlags;
+ u32 conformanceTestLimit[3]; /* 0:11a, 1: 11b, 2:11g */
+#ifdef ATH_NF_PER_CHAN
+ struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
+#endif
+};
+
+#define IS_CHAN_A(_c) ((((_c)->channelFlags & CHANNEL_A) == CHANNEL_A) || \
+ (((_c)->channelFlags & CHANNEL_A_HT20) == CHANNEL_A_HT20) || \
+ (((_c)->channelFlags & CHANNEL_A_HT40PLUS) == CHANNEL_A_HT40PLUS) || \
+ (((_c)->channelFlags & CHANNEL_A_HT40MINUS) == CHANNEL_A_HT40MINUS))
+#define IS_CHAN_B(_c) (((_c)->channelFlags & CHANNEL_B) == CHANNEL_B)
+#define IS_CHAN_G(_c) ((((_c)->channelFlags & (CHANNEL_G)) == CHANNEL_G) || \
+ (((_c)->channelFlags & CHANNEL_G_HT20) == CHANNEL_G_HT20) || \
+ (((_c)->channelFlags & CHANNEL_G_HT40PLUS) == CHANNEL_G_HT40PLUS) || \
+ (((_c)->channelFlags & CHANNEL_G_HT40MINUS) == CHANNEL_G_HT40MINUS))
+#define IS_CHAN_CCK(_c) (((_c)->channelFlags & CHANNEL_CCK) != 0)
+#define IS_CHAN_OFDM(_c) (((_c)->channelFlags & CHANNEL_OFDM) != 0)
+#define IS_CHAN_5GHZ(_c) (((_c)->channelFlags & CHANNEL_5GHZ) != 0)
+#define IS_CHAN_2GHZ(_c) (((_c)->channelFlags & CHANNEL_2GHZ) != 0)
+#define IS_CHAN_PASSIVE(_c) (((_c)->channelFlags & CHANNEL_PASSIVE) != 0)
+#define IS_CHAN_HALF_RATE(_c) (((_c)->channelFlags & CHANNEL_HALF) != 0)
+#define IS_CHAN_QUARTER_RATE(_c) (((_c)->channelFlags & CHANNEL_QUARTER) != 0)
+
+/* These macros check chanmode and not channelFlags */
+#define IS_CHAN_HT20(_c) (((_c)->chanmode == CHANNEL_A_HT20) || \
+ ((_c)->chanmode == CHANNEL_G_HT20))
+#define IS_CHAN_HT40(_c) (((_c)->chanmode == CHANNEL_A_HT40PLUS) || \
+ ((_c)->chanmode == CHANNEL_A_HT40MINUS) || \
+ ((_c)->chanmode == CHANNEL_G_HT40PLUS) || \
+ ((_c)->chanmode == CHANNEL_G_HT40MINUS))
+#define IS_CHAN_HT(_c) (IS_CHAN_HT20((_c)) || IS_CHAN_HT40((_c)))
+
+#define IS_CHAN_IN_PUBLIC_SAFETY_BAND(_c) ((_c) > 4940 && (_c) < 4990)
+#define IS_CHAN_A_5MHZ_SPACED(_c) \
+ ((((_c)->channelFlags & CHANNEL_5GHZ) != 0) && \
+ (((_c)->channel % 20) != 0) && \
+ (((_c)->channel % 10) != 0))
+
+struct ath9k_keyval {
+ u8 kv_type;
+ u8 kv_pad;
+ u16 kv_len;
+ u8 kv_val[16];
+ u8 kv_mic[8];
+ u8 kv_txmic[8];
+};
+
+enum ath9k_key_type {
+ ATH9K_KEY_TYPE_CLEAR,
+ ATH9K_KEY_TYPE_WEP,
+ ATH9K_KEY_TYPE_AES,
+ ATH9K_KEY_TYPE_TKIP,
+};
+
+enum ath9k_cipher {
+ ATH9K_CIPHER_WEP = 0,
+ ATH9K_CIPHER_AES_OCB = 1,
+ ATH9K_CIPHER_AES_CCM = 2,
+ ATH9K_CIPHER_CKIP = 3,
+ ATH9K_CIPHER_TKIP = 4,
+ ATH9K_CIPHER_CLR = 5,
+ ATH9K_CIPHER_MIC = 127
+};
+
+#define AR_EEPROM_EEPCAP_COMPRESS_DIS 0x0001
+#define AR_EEPROM_EEPCAP_AES_DIS 0x0002
+#define AR_EEPROM_EEPCAP_FASTFRAME_DIS 0x0004
+#define AR_EEPROM_EEPCAP_BURST_DIS 0x0008
+#define AR_EEPROM_EEPCAP_MAXQCU 0x01F0
+#define AR_EEPROM_EEPCAP_MAXQCU_S 4
+#define AR_EEPROM_EEPCAP_HEAVY_CLIP_EN 0x0200
+#define AR_EEPROM_EEPCAP_KC_ENTRIES 0xF000
+#define AR_EEPROM_EEPCAP_KC_ENTRIES_S 12
+
+#define AR_EEPROM_EEREGCAP_EN_FCC_MIDBAND 0x0040
+#define AR_EEPROM_EEREGCAP_EN_KK_U1_EVEN 0x0080
+#define AR_EEPROM_EEREGCAP_EN_KK_U2 0x0100
+#define AR_EEPROM_EEREGCAP_EN_KK_MIDBAND 0x0200
+#define AR_EEPROM_EEREGCAP_EN_KK_U1_ODD 0x0400
+#define AR_EEPROM_EEREGCAP_EN_KK_NEW_11A 0x0800
+
+#define AR_EEPROM_EEREGCAP_EN_KK_U1_ODD_PRE4_0 0x4000
+#define AR_EEPROM_EEREGCAP_EN_KK_NEW_11A_PRE4_0 0x8000
+
+#define SD_NO_CTL 0xE0
+#define NO_CTL 0xff
+#define CTL_MODE_M 7
+#define CTL_11A 0
+#define CTL_11B 1
+#define CTL_11G 2
+#define CTL_2GHT20 5
+#define CTL_5GHT20 6
+#define CTL_2GHT40 7
+#define CTL_5GHT40 8
+
+#define AR_EEPROM_MAC(i) (0x1d+(i))
+#define EEP_SCALE 100
+#define EEP_DELTA 10
+
+#define AR_EEPROM_RFSILENT_GPIO_SEL 0x001c
+#define AR_EEPROM_RFSILENT_GPIO_SEL_S 2
+#define AR_EEPROM_RFSILENT_POLARITY 0x0002
+#define AR_EEPROM_RFSILENT_POLARITY_S 1
+
+#define CTRY_DEBUG 0x1ff
+#define CTRY_DEFAULT 0
+
+enum reg_ext_bitmap {
+ REG_EXT_JAPAN_MIDBAND = 1,
+ REG_EXT_FCC_DFS_HT40 = 2,
+ REG_EXT_JAPAN_NONDFS_HT40 = 3,
+ REG_EXT_JAPAN_DFS_HT40 = 4
+};
+
+struct ath9k_country_entry {
+ u16 countryCode;
+ u16 regDmnEnum;
+ u16 regDmn5G;
+ u16 regDmn2G;
+ u8 isMultidomain;
+ u8 iso[3];
+};
+
+#define REG_WRITE(_ah, _reg, _val) iowrite32(_val, _ah->ah_sh + _reg)
+#define REG_READ(_ah, _reg) ioread32(_ah->ah_sh + _reg)
+
+#define SM(_v, _f) (((_v) << _f##_S) & _f)
+#define MS(_v, _f) (((_v) & _f) >> _f##_S)
+#define REG_RMW(_a, _r, _set, _clr) \
+ REG_WRITE(_a, _r, (REG_READ(_a, _r) & ~(_clr)) | (_set))
+#define REG_RMW_FIELD(_a, _r, _f, _v) \
+ REG_WRITE(_a, _r, \
+ (REG_READ(_a, _r) & ~_f) | (((_v) << _f##_S) & _f))
+#define REG_SET_BIT(_a, _r, _f) \
+ REG_WRITE(_a, _r, REG_READ(_a, _r) | _f)
+#define REG_CLR_BIT(_a, _r, _f) \
+ REG_WRITE(_a, _r, REG_READ(_a, _r) & ~_f)
+
+#define ATH9K_COMP_BUF_MAX_SIZE 9216
+#define ATH9K_COMP_BUF_ALIGN_SIZE 512
+
+#define ATH9K_TXQ_USE_LOCKOUT_BKOFF_DIS 0x00000001
+
+#define INIT_AIFS 2
+#define INIT_CWMIN 15
+#define INIT_CWMIN_11B 31
+#define INIT_CWMAX 1023
+#define INIT_SH_RETRY 10
+#define INIT_LG_RETRY 10
+#define INIT_SSH_RETRY 32
+#define INIT_SLG_RETRY 32
+
+#define WLAN_CTRL_FRAME_SIZE (2+2+6+4)
+
+#define ATH_AMPDU_LIMIT_MAX (64 * 1024 - 1)
+#define ATH_AMPDU_LIMIT_DEFAULT ATH_AMPDU_LIMIT_MAX
+
+#define IEEE80211_WEP_IVLEN 3
+#define IEEE80211_WEP_KIDLEN 1
+#define IEEE80211_WEP_CRCLEN 4
+#define IEEE80211_MAX_MPDU_LEN (3840 + FCS_LEN + \
+ (IEEE80211_WEP_IVLEN + \
+ IEEE80211_WEP_KIDLEN + \
+ IEEE80211_WEP_CRCLEN))
+#define IEEE80211_MAX_LEN (2300 + FCS_LEN + \
+ (IEEE80211_WEP_IVLEN + \
+ IEEE80211_WEP_KIDLEN + \
+ IEEE80211_WEP_CRCLEN))
+
+#define MAX_REG_ADD_COUNT 129
+#define MAX_RATE_POWER 63
+
+enum ath9k_power_mode {
+ ATH9K_PM_AWAKE = 0,
+ ATH9K_PM_FULL_SLEEP,
+ ATH9K_PM_NETWORK_SLEEP,
+ ATH9K_PM_UNDEFINED
+};
+
+struct ath9k_mib_stats {
+ u32 ackrcv_bad;
+ u32 rts_bad;
+ u32 rts_good;
+ u32 fcs_bad;
+ u32 beacons;
+};
+
+enum ath9k_ant_setting {
+ ATH9K_ANT_VARIABLE = 0,
+ ATH9K_ANT_FIXED_A,
+ ATH9K_ANT_FIXED_B
+};
+
+enum ath9k_opmode {
+ ATH9K_M_STA = 1,
+ ATH9K_M_IBSS = 0,
+ ATH9K_M_HOSTAP = 6,
+ ATH9K_M_MONITOR = 8
+};
+
+#define ATH9K_SLOT_TIME_6 6
+#define ATH9K_SLOT_TIME_9 9
+#define ATH9K_SLOT_TIME_20 20
+
+enum ath9k_ht_macmode {
+ ATH9K_HT_MACMODE_20 = 0,
+ ATH9K_HT_MACMODE_2040 = 1,
+};
+
+enum ath9k_ht_extprotspacing {
+ ATH9K_HT_EXTPROTSPACING_20 = 0,
+ ATH9K_HT_EXTPROTSPACING_25 = 1,
+};
+
+struct ath9k_ht_cwm {
+ enum ath9k_ht_macmode ht_macmode;
+ enum ath9k_ht_extprotspacing ht_extprotspacing;
+};
+
+enum ath9k_ani_cmd {
+ ATH9K_ANI_PRESENT = 0x1,
+ ATH9K_ANI_NOISE_IMMUNITY_LEVEL = 0x2,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION = 0x4,
+ ATH9K_ANI_CCK_WEAK_SIGNAL_THR = 0x8,
+ ATH9K_ANI_FIRSTEP_LEVEL = 0x10,
+ ATH9K_ANI_SPUR_IMMUNITY_LEVEL = 0x20,
+ ATH9K_ANI_MODE = 0x40,
+ ATH9K_ANI_PHYERR_RESET = 0x80,
+ ATH9K_ANI_ALL = 0xff
+};
+
+enum phytype {
+ PHY_DS,
+ PHY_FH,
+ PHY_OFDM,
+ PHY_HT,
+};
+#define PHY_CCK PHY_DS
+
+enum start_adhoc_option {
+ START_ADHOC_NO_11A,
+ START_ADHOC_PER_11D,
+ START_ADHOC_IN_11A,
+ START_ADHOC_IN_11B,
+};
+
+enum ath9k_tp_scale {
+ ATH9K_TP_SCALE_MAX = 0,
+ ATH9K_TP_SCALE_50,
+ ATH9K_TP_SCALE_25,
+ ATH9K_TP_SCALE_12,
+ ATH9K_TP_SCALE_MIN
+};
+
+enum ser_reg_mode {
+ SER_REG_MODE_OFF = 0,
+ SER_REG_MODE_ON = 1,
+ SER_REG_MODE_AUTO = 2,
+};
+
+#define AR_PHY_CCA_MAX_GOOD_VALUE -85
+#define AR_PHY_CCA_MAX_HIGH_VALUE -62
+#define AR_PHY_CCA_MIN_BAD_VALUE -121
+#define AR_PHY_CCA_FILTERWINDOW_LENGTH_INIT 3
+#define AR_PHY_CCA_FILTERWINDOW_LENGTH 5
+
+#define ATH9K_NF_CAL_HIST_MAX 5
+#define NUM_NF_READINGS 6
+
+struct ath9k_nfcal_hist {
+ int16_t nfCalBuffer[ATH9K_NF_CAL_HIST_MAX];
+ u8 currIndex;
+ int16_t privNF;
+ u8 invalidNFcount;
+};
+
+struct ath9k_beacon_state {
+ u32 bs_nexttbtt;
+ u32 bs_nextdtim;
+ u32 bs_intval;
+#define ATH9K_BEACON_PERIOD 0x0000ffff
+#define ATH9K_BEACON_ENA 0x00800000
+#define ATH9K_BEACON_RESET_TSF 0x01000000
+ u32 bs_dtimperiod;
+ u16 bs_cfpperiod;
+ u16 bs_cfpmaxduration;
+ u32 bs_cfpnext;
+ u16 bs_timoffset;
+ u16 bs_bmissthreshold;
+ u32 bs_sleepduration;
+};
+
+struct ath9k_node_stats {
+ u32 ns_avgbrssi;
+ u32 ns_avgrssi;
+ u32 ns_avgtxrssi;
+ u32 ns_avgtxrate;
+};
+
+#define ATH9K_RSSI_EP_MULTIPLIER (1<<7)
+
+enum ath9k_gpio_output_mux_type {
+ ATH9K_GPIO_OUTPUT_MUX_AS_OUTPUT,
+ ATH9K_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED,
+ ATH9K_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED,
+ ATH9K_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED,
+ ATH9K_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED,
+ ATH9K_GPIO_OUTPUT_MUX_NUM_ENTRIES
+};
+
+enum {
+ ATH9K_RESET_POWER_ON,
+ ATH9K_RESET_WARM,
+ ATH9K_RESET_COLD,
+};
+
+#define AH_USE_EEPROM 0x1
+
+struct ath_hal {
+ u32 ah_magic;
+ u16 ah_devid;
+ u16 ah_subvendorid;
+ struct ath_softc *ah_sc;
+ void __iomem *ah_sh;
+ u16 ah_countryCode;
+ u32 ah_macVersion;
+ u16 ah_macRev;
+ u16 ah_phyRev;
+ u16 ah_analog5GhzRev;
+ u16 ah_analog2GhzRev;
+ u8 ah_decompMask[ATH9K_DECOMP_MASK_SIZE];
+ u32 ah_flags;
+ enum ath9k_opmode ah_opmode;
+ struct ath9k_ops_config ah_config;
+ struct ath9k_hw_capabilities ah_caps;
+ int16_t ah_powerLimit;
+ u16 ah_maxPowerLevel;
+ u32 ah_tpScale;
+ u16 ah_currentRD;
+ u16 ah_currentRDExt;
+ u16 ah_currentRDInUse;
+ u16 ah_currentRD5G;
+ u16 ah_currentRD2G;
+ char ah_iso[4];
+ enum start_adhoc_option ah_adHocMode;
+ bool ah_commonMode;
+ struct ath9k_channel ah_channels[150];
+ u32 ah_nchan;
+ struct ath9k_channel *ah_curchan;
+ u16 ah_rfsilent;
+ bool ah_rfkillEnabled;
+ bool ah_isPciExpress;
+ u16 ah_txTrigLevel;
+#ifndef ATH_NF_PER_CHAN
+ struct ath9k_nfcal_hist nfCalHist[NUM_NF_READINGS];
+#endif
+};
+
+struct chan_centers {
+ u16 synth_center;
+ u16 ctl_center;
+ u16 ext_center;
+};
+
+int ath_hal_getcapability(struct ath_hal *ah,
+ enum ath9k_capability_type type,
+ u32 capability,
+ u32 *result);
+const struct ath9k_rate_table *ath9k_hw_getratetable(struct ath_hal *ah,
+ u32 mode);
+void ath9k_hw_detach(struct ath_hal *ah);
+struct ath_hal *ath9k_hw_attach(u16 devid,
+ struct ath_softc *sc,
+ void __iomem *mem,
+ int *error);
+bool ath9k_regd_init_channels(struct ath_hal *ah,
+ u32 maxchans, u32 *nchans,
+ u8 *regclassids,
+ u32 maxregids, u32 *nregids,
+ u16 cc,
+ bool enableOutdoor,
+ bool enableExtendedChannels);
+u32 ath9k_hw_mhz2ieee(struct ath_hal *ah, u32 freq, u32 flags);
+enum ath9k_int ath9k_hw_set_interrupts(struct ath_hal *ah,
+ enum ath9k_int ints);
+bool ath9k_hw_reset(struct ath_hal *ah, enum ath9k_opmode opmode,
+ struct ath9k_channel *chan,
+ enum ath9k_ht_macmode macmode,
+ u8 txchainmask, u8 rxchainmask,
+ enum ath9k_ht_extprotspacing extprotspacing,
+ bool bChannelChange,
+ int *status);
+bool ath9k_hw_phy_disable(struct ath_hal *ah);
+void ath9k_hw_reset_calvalid(struct ath_hal *ah, struct ath9k_channel *chan,
+ bool *isCalDone);
+void ath9k_hw_ani_monitor(struct ath_hal *ah,
+ const struct ath9k_node_stats *stats,
+ struct ath9k_channel *chan);
+bool ath9k_hw_calibrate(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ u8 rxchainmask,
+ bool longcal,
+ bool *isCalDone);
+int16_t ath9k_hw_getchan_noise(struct ath_hal *ah,
+ struct ath9k_channel *chan);
+void ath9k_hw_write_associd(struct ath_hal *ah, const u8 *bssid,
+ u16 assocId);
+void ath9k_hw_setrxfilter(struct ath_hal *ah, u32 bits);
+void ath9k_hw_write_associd(struct ath_hal *ah, const u8 *bssid,
+ u16 assocId);
+bool ath9k_hw_stoptxdma(struct ath_hal *ah, u32 q);
+void ath9k_hw_reset_tsf(struct ath_hal *ah);
+bool ath9k_hw_keyisvalid(struct ath_hal *ah, u16 entry);
+bool ath9k_hw_keysetmac(struct ath_hal *ah, u16 entry,
+ const u8 *mac);
+bool ath9k_hw_set_keycache_entry(struct ath_hal *ah,
+ u16 entry,
+ const struct ath9k_keyval *k,
+ const u8 *mac,
+ int xorKey);
+bool ath9k_hw_set_tsfadjust(struct ath_hal *ah,
+ u32 setting);
+void ath9k_hw_configpcipowersave(struct ath_hal *ah, int restore);
+bool ath9k_hw_intrpend(struct ath_hal *ah);
+bool ath9k_hw_getisr(struct ath_hal *ah, enum ath9k_int *masked);
+bool ath9k_hw_updatetxtriglevel(struct ath_hal *ah,
+ bool bIncTrigLevel);
+void ath9k_hw_procmibevent(struct ath_hal *ah,
+ const struct ath9k_node_stats *stats);
+bool ath9k_hw_setrxabort(struct ath_hal *ah, bool set);
+void ath9k_hw_set11nmac2040(struct ath_hal *ah, enum ath9k_ht_macmode mode);
+bool ath9k_hw_phycounters(struct ath_hal *ah);
+bool ath9k_hw_keyreset(struct ath_hal *ah, u16 entry);
+bool ath9k_hw_getcapability(struct ath_hal *ah,
+ enum ath9k_capability_type type,
+ u32 capability,
+ u32 *result);
+bool ath9k_hw_setcapability(struct ath_hal *ah,
+ enum ath9k_capability_type type,
+ u32 capability,
+ u32 setting,
+ int *status);
+u32 ath9k_hw_getdefantenna(struct ath_hal *ah);
+void ath9k_hw_getmac(struct ath_hal *ah, u8 *mac);
+void ath9k_hw_getbssidmask(struct ath_hal *ah, u8 *mask);
+bool ath9k_hw_setbssidmask(struct ath_hal *ah,
+ const u8 *mask);
+bool ath9k_hw_setpower(struct ath_hal *ah,
+ enum ath9k_power_mode mode);
+enum ath9k_int ath9k_hw_intrget(struct ath_hal *ah);
+u64 ath9k_hw_gettsf64(struct ath_hal *ah);
+u32 ath9k_hw_getdefantenna(struct ath_hal *ah);
+bool ath9k_hw_setslottime(struct ath_hal *ah, u32 us);
+bool ath9k_hw_setantennaswitch(struct ath_hal *ah,
+ enum ath9k_ant_setting settings,
+ struct ath9k_channel *chan,
+ u8 *tx_chainmask,
+ u8 *rx_chainmask,
+ u8 *antenna_cfgd);
+void ath9k_hw_setantenna(struct ath_hal *ah, u32 antenna);
+int ath9k_hw_select_antconfig(struct ath_hal *ah,
+ u32 cfg);
+bool ath9k_hw_puttxbuf(struct ath_hal *ah, u32 q,
+ u32 txdp);
+bool ath9k_hw_txstart(struct ath_hal *ah, u32 q);
+u16 ath9k_hw_computetxtime(struct ath_hal *ah,
+ const struct ath9k_rate_table *rates,
+ u32 frameLen, u16 rateix,
+ bool shortPreamble);
+void ath9k_hw_set11n_ratescenario(struct ath_hal *ah, struct ath_desc *ds,
+ struct ath_desc *lastds,
+ u32 durUpdateEn, u32 rtsctsRate,
+ u32 rtsctsDuration,
+ struct ath9k_11n_rate_series series[],
+ u32 nseries, u32 flags);
+void ath9k_hw_set11n_burstduration(struct ath_hal *ah,
+ struct ath_desc *ds,
+ u32 burstDuration);
+void ath9k_hw_cleartxdesc(struct ath_hal *ah, struct ath_desc *ds);
+u32 ath9k_hw_reverse_bits(u32 val, u32 n);
+bool ath9k_hw_resettxqueue(struct ath_hal *ah, u32 q);
+u32 ath9k_regd_get_ctl(struct ath_hal *ah, struct ath9k_channel *chan);
+u32 ath9k_regd_get_antenna_allowed(struct ath_hal *ah,
+ struct ath9k_channel *chan);
+u32 ath9k_hw_mhz2ieee(struct ath_hal *ah, u32 freq, u32 flags);
+bool ath9k_hw_get_txq_props(struct ath_hal *ah, int q,
+ struct ath9k_tx_queue_info *qinfo);
+bool ath9k_hw_set_txq_props(struct ath_hal *ah, int q,
+ const struct ath9k_tx_queue_info *qinfo);
+struct ath9k_channel *ath9k_regd_check_channel(struct ath_hal *ah,
+ const struct ath9k_channel *c);
+void ath9k_hw_set11n_txdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 pktLen, enum ath9k_pkt_type type,
+ u32 txPower, u32 keyIx,
+ enum ath9k_key_type keyType, u32 flags);
+bool ath9k_hw_filltxdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 segLen, bool firstSeg,
+ bool lastSeg,
+ const struct ath_desc *ds0);
+u32 ath9k_hw_GetMibCycleCountsPct(struct ath_hal *ah,
+ u32 *rxc_pcnt,
+ u32 *rxf_pcnt,
+ u32 *txf_pcnt);
+void ath9k_hw_dmaRegDump(struct ath_hal *ah);
+void ath9k_hw_beaconinit(struct ath_hal *ah,
+ u32 next_beacon, u32 beacon_period);
+void ath9k_hw_set_sta_beacon_timers(struct ath_hal *ah,
+ const struct ath9k_beacon_state *bs);
+bool ath9k_hw_setuprxdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 size, u32 flags);
+void ath9k_hw_putrxbuf(struct ath_hal *ah, u32 rxdp);
+void ath9k_hw_rxena(struct ath_hal *ah);
+void ath9k_hw_setopmode(struct ath_hal *ah);
+bool ath9k_hw_setmac(struct ath_hal *ah, const u8 *mac);
+void ath9k_hw_setmcastfilter(struct ath_hal *ah, u32 filter0,
+ u32 filter1);
+u32 ath9k_hw_getrxfilter(struct ath_hal *ah);
+void ath9k_hw_startpcureceive(struct ath_hal *ah);
+void ath9k_hw_stoppcurecv(struct ath_hal *ah);
+bool ath9k_hw_stopdmarecv(struct ath_hal *ah);
+int ath9k_hw_rxprocdesc(struct ath_hal *ah,
+ struct ath_desc *ds, u32 pa,
+ struct ath_desc *nds, u64 tsf);
+u32 ath9k_hw_gettxbuf(struct ath_hal *ah, u32 q);
+int ath9k_hw_txprocdesc(struct ath_hal *ah,
+ struct ath_desc *ds);
+void ath9k_hw_set11n_aggr_middle(struct ath_hal *ah, struct ath_desc *ds,
+ u32 numDelims);
+void ath9k_hw_set11n_aggr_first(struct ath_hal *ah, struct ath_desc *ds,
+ u32 aggrLen);
+void ath9k_hw_set11n_aggr_last(struct ath_hal *ah, struct ath_desc *ds);
+bool ath9k_hw_releasetxqueue(struct ath_hal *ah, u32 q);
+void ath9k_hw_gettxintrtxqs(struct ath_hal *ah, u32 *txqs);
+void ath9k_hw_clr11n_aggr(struct ath_hal *ah, struct ath_desc *ds);
+void ath9k_hw_set11n_virtualmorefrag(struct ath_hal *ah,
+ struct ath_desc *ds, u32 vmf);
+bool ath9k_hw_set_txpowerlimit(struct ath_hal *ah, u32 limit);
+bool ath9k_regd_is_public_safety_sku(struct ath_hal *ah);
+int ath9k_hw_setuptxqueue(struct ath_hal *ah, enum ath9k_tx_queue type,
+ const struct ath9k_tx_queue_info *qinfo);
+u32 ath9k_hw_numtxpending(struct ath_hal *ah, u32 q);
+const char *ath9k_hw_probe(u16 vendorid, u16 devid);
+bool ath9k_hw_disable(struct ath_hal *ah);
+void ath9k_hw_rfdetach(struct ath_hal *ah);
+void ath9k_hw_get_channel_centers(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ struct chan_centers *centers);
+bool ath9k_get_channel_edges(struct ath_hal *ah,
+ u16 flags, u16 *low,
+ u16 *high);
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+ /* Implementation of beacon processing. */
+
+#include <asm/unaligned.h>
+#include "core.h"
+
+/*
+ * Configure parameters for the beacon queue
+ *
+ * This function will modify certain transmit queue properties depending on
+ * the operating mode of the station (AP or AdHoc). Parameters are AIFS
+ * settings and channel width min/max
+*/
+
+static int ath_beaconq_config(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath9k_tx_queue_info qi;
+
+ ath9k_hw_get_txq_props(ah, sc->sc_bhalq, &qi);
+ if (sc->sc_opmode == ATH9K_M_HOSTAP) {
+ /* Always burst out beacon and CAB traffic. */
+ qi.tqi_aifs = 1;
+ qi.tqi_cwmin = 0;
+ qi.tqi_cwmax = 0;
+ } else {
+ /* Adhoc mode; important thing is to use 2x cwmin. */
+ qi.tqi_aifs = sc->sc_beacon_qi.tqi_aifs;
+ qi.tqi_cwmin = 2*sc->sc_beacon_qi.tqi_cwmin;
+ qi.tqi_cwmax = sc->sc_beacon_qi.tqi_cwmax;
+ }
+
+ if (!ath9k_hw_set_txq_props(ah, sc->sc_bhalq, &qi)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to update h/w beacon queue parameters\n",
+ __func__);
+ return 0;
+ } else {
+ ath9k_hw_resettxqueue(ah, sc->sc_bhalq); /* push to h/w */
+ return 1;
+ }
+}
+
+/*
+ * Setup the beacon frame for transmit.
+ *
+ * Associates the beacon frame buffer with a transmit descriptor. Will set
+ * up all required antenna switch parameters, rate codes, and channel flags.
+ * Beacons are always sent out at the lowest rate, and are not retried.
+*/
+
+static void ath_beacon_setup(struct ath_softc *sc,
+ struct ath_vap *avp, struct ath_buf *bf)
+{
+ struct sk_buff *skb = (struct sk_buff *)bf->bf_mpdu;
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_desc *ds;
+ int flags, antenna;
+ const struct ath9k_rate_table *rt;
+ u8 rix, rate;
+ int ctsrate = 0;
+ int ctsduration = 0;
+ struct ath9k_11n_rate_series series[4];
+
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: m %p len %u\n",
+ __func__, skb, skb->len);
+
+ /* setup descriptors */
+ ds = bf->bf_desc;
+
+ flags = ATH9K_TXDESC_NOACK;
+
+ if (sc->sc_opmode == ATH9K_M_IBSS &&
+ (ah->ah_caps.hw_caps & ATH9K_HW_CAP_VEOL)) {
+ ds->ds_link = bf->bf_daddr; /* self-linked */
+ flags |= ATH9K_TXDESC_VEOL;
+ /* Let hardware handle antenna switching. */
+ antenna = 0;
+ } else {
+ ds->ds_link = 0;
+ /*
+ * Switch antenna every beacon.
+ * Should only switch every beacon period, not for every
+ * SWBA's
+ * XXX assumes two antenna
+ */
+ antenna = ((sc->ast_be_xmit / sc->sc_nbcnvaps) & 1 ? 2 : 1);
+ }
+
+ ds->ds_data = bf->bf_buf_addr;
+
+ /*
+ * Calculate rate code.
+ * XXX everything at min xmit rate
+ */
+ rix = 0;
+ rt = sc->sc_currates;
+ rate = rt->info[rix].rateCode;
+ if (sc->sc_flags & ATH_PREAMBLE_SHORT)
+ rate |= rt->info[rix].shortPreamble;
+
+ ath9k_hw_set11n_txdesc(ah, ds
+ , skb->len + FCS_LEN /* frame length */
+ , ATH9K_PKT_TYPE_BEACON /* Atheros packet type */
+ , avp->av_btxctl.txpower /* txpower XXX */
+ , ATH9K_TXKEYIX_INVALID /* no encryption */
+ , ATH9K_KEY_TYPE_CLEAR /* no encryption */
+ , flags /* no ack, veol for beacons */
+ );
+
+ /* NB: beacon's BufLen must be a multiple of 4 bytes */
+ ath9k_hw_filltxdesc(ah, ds
+ , roundup(skb->len, 4) /* buffer length */
+ , true /* first segment */
+ , true /* last segment */
+ , ds /* first descriptor */
+ );
+
+ memzero(series, sizeof(struct ath9k_11n_rate_series) * 4);
+ series[0].Tries = 1;
+ series[0].Rate = rate;
+ series[0].ChSel = sc->sc_tx_chainmask;
+ series[0].RateFlags = (ctsrate) ? ATH9K_RATESERIES_RTS_CTS : 0;
+ ath9k_hw_set11n_ratescenario(ah, ds, ds, 0,
+ ctsrate, ctsduration, series, 4, 0);
+}
+
+/* Move everything from the vap's mcast queue to the hardware cab queue.
+ * Caller must hold mcasq lock and cabq lock
+ * XXX MORE_DATA bit?
+ */
+static void empty_mcastq_into_cabq(struct ath_hal *ah,
+ struct ath_txq *mcastq, struct ath_txq *cabq)
+{
+ struct ath_buf *bfmcast;
+
+ BUG_ON(list_empty(&mcastq->axq_q));
+
+ bfmcast = list_first_entry(&mcastq->axq_q, struct ath_buf, list);
+
+ /* link the descriptors */
+ if (!cabq->axq_link)
+ ath9k_hw_puttxbuf(ah, cabq->axq_qnum, bfmcast->bf_daddr);
+ else
+ *cabq->axq_link = bfmcast->bf_daddr;
+
+ /* append the private vap mcast list to the cabq */
+
+ cabq->axq_depth += mcastq->axq_depth;
+ cabq->axq_totalqueued += mcastq->axq_totalqueued;
+ cabq->axq_linkbuf = mcastq->axq_linkbuf;
+ cabq->axq_link = mcastq->axq_link;
+ list_splice_tail_init(&mcastq->axq_q, &cabq->axq_q);
+ mcastq->axq_depth = 0;
+ mcastq->axq_totalqueued = 0;
+ mcastq->axq_linkbuf = NULL;
+ mcastq->axq_link = NULL;
+}
+
+/* This is only run at DTIM. We move everything from the vap's mcast queue
+ * to the hardware cab queue. Caller must hold the mcastq lock. */
+static void trigger_mcastq(struct ath_hal *ah,
+ struct ath_txq *mcastq, struct ath_txq *cabq)
+{
+ spin_lock_bh(&cabq->axq_lock);
+
+ if (!list_empty(&mcastq->axq_q))
+ empty_mcastq_into_cabq(ah, mcastq, cabq);
+
+ /* cabq is gated by beacon so it is safe to start here */
+ if (!list_empty(&cabq->axq_q))
+ ath9k_hw_txstart(ah, cabq->axq_qnum);
+
+ spin_unlock_bh(&cabq->axq_lock);
+}
+
+/*
+ * Generate beacon frame and queue cab data for a vap.
+ *
+ * Updates the contents of the beacon frame. It is assumed that the buffer for
+ * the beacon frame has been allocated in the ATH object, and simply needs to
+ * be filled for this cycle. Also, any CAB (crap after beacon?) traffic will
+ * be added to the beacon frame at this point.
+*/
+static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf;
+ struct ath_vap *avp;
+ struct sk_buff *skb;
+ int cabq_depth;
+ int mcastq_depth;
+ int is_beacon_dtim = 0;
+ unsigned int curlen;
+ struct ath_txq *cabq;
+ struct ath_txq *mcastq;
+ avp = sc->sc_vaps[if_id];
+
+ mcastq = &avp->av_mcastq;
+ cabq = sc->sc_cabq;
+
+ ASSERT(avp);
+
+ if (avp->av_bcbuf == NULL) {
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: avp=%p av_bcbuf=%p\n",
+ __func__, avp, avp->av_bcbuf);
+ return NULL;
+ }
+ bf = avp->av_bcbuf;
+ skb = (struct sk_buff *) bf->bf_mpdu;
+
+ /*
+ * Update dynamic beacon contents. If this returns
+ * non-zero then we need to remap the memory because
+ * the beacon frame changed size (probably because
+ * of the TIM bitmap).
+ */
+ curlen = skb->len;
+
+ /* XXX: spin_lock_bh should not be used here, but sparse bitches
+ * otherwise. We should fix sparse :) */
+ spin_lock_bh(&mcastq->axq_lock);
+ mcastq_depth = avp->av_mcastq.axq_depth;
+
+ if (ath_update_beacon(sc, if_id, &avp->av_boff, skb, mcastq_depth) ==
+ 1) {
+ ath_skb_unmap_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ bf->bf_buf_addr = ath_skb_map_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ } else {
+ pci_dma_sync_single_for_cpu(sc->pdev,
+ bf->bf_buf_addr,
+ skb_tailroom(skb),
+ PCI_DMA_TODEVICE);
+ }
+
+ /*
+ * if the CABQ traffic from previous DTIM is pending and the current
+ * beacon is also a DTIM.
+ * 1) if there is only one vap let the cab traffic continue.
+ * 2) if there are more than one vap and we are using staggered
+ * beacons, then drain the cabq by dropping all the frames in
+ * the cabq so that the current vaps cab traffic can be scheduled.
+ */
+ spin_lock_bh(&cabq->axq_lock);
+ cabq_depth = cabq->axq_depth;
+ spin_unlock_bh(&cabq->axq_lock);
+
+ is_beacon_dtim = avp->av_boff.bo_tim[4] & 1;
+
+ if (mcastq_depth && is_beacon_dtim && cabq_depth) {
+ /*
+ * Unlock the cabq lock as ath_tx_draintxq acquires
+ * the lock again which is a common function and that
+ * acquires txq lock inside.
+ */
+ if (sc->sc_nvaps > 1) {
+ ath_tx_draintxq(sc, cabq, false);
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: flush previous cabq traffic\n", __func__);
+ }
+ }
+
+ /* Construct tx descriptor. */
+ ath_beacon_setup(sc, avp, bf);
+
+ /*
+ * Enable the CAB queue before the beacon queue to
+ * insure cab frames are triggered by this beacon.
+ */
+ if (is_beacon_dtim)
+ trigger_mcastq(ah, mcastq, cabq);
+
+ spin_unlock_bh(&mcastq->axq_lock);
+ return bf;
+}
+
+/*
+ * Startup beacon transmission for adhoc mode when they are sent entirely
+ * by the hardware using the self-linked descriptor + veol trick.
+*/
+
+static void ath_beacon_start_adhoc(struct ath_softc *sc, int if_id)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf;
+ struct ath_vap *avp;
+ struct sk_buff *skb;
+
+ avp = sc->sc_vaps[if_id];
+ ASSERT(avp);
+
+ if (avp->av_bcbuf == NULL) {
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: avp=%p av_bcbuf=%p\n",
+ __func__, avp, avp != NULL ? avp->av_bcbuf : NULL);
+ return;
+ }
+ bf = avp->av_bcbuf;
+ skb = (struct sk_buff *) bf->bf_mpdu;
+
+ /* Construct tx descriptor. */
+ ath_beacon_setup(sc, avp, bf);
+
+ /* NB: caller is known to have already stopped tx dma */
+ ath9k_hw_puttxbuf(ah, sc->sc_bhalq, bf->bf_daddr);
+ ath9k_hw_txstart(ah, sc->sc_bhalq);
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: TXDP%u = %llx (%p)\n", __func__,
+ sc->sc_bhalq, ito64(bf->bf_daddr), bf->bf_desc);
+}
+
+/*
+ * Setup a h/w transmit queue for beacons.
+ *
+ * This function allocates an information structure (struct ath9k_txq_info)
+ * on the stack, sets some specific parameters (zero out channel width
+ * min/max, and enable aifs). The info structure does not need to be
+ * persistant.
+*/
+
+int ath_beaconq_setup(struct ath_hal *ah)
+{
+ struct ath9k_tx_queue_info qi;
+
+ memzero(&qi, sizeof(qi));
+ qi.tqi_aifs = 1;
+ qi.tqi_cwmin = 0;
+ qi.tqi_cwmax = 0;
+ /* NB: don't enable any interrupts */
+ return ath9k_hw_setuptxqueue(ah, ATH9K_TX_QUEUE_BEACON, &qi);
+}
+
+
+/*
+ * Allocate and setup an initial beacon frame.
+ *
+ * Allocate a beacon state variable for a specific VAP instance created on
+ * the ATH interface. This routine also calculates the beacon "slot" for
+ * staggared beacons in the mBSSID case.
+*/
+
+int ath_beacon_alloc(struct ath_softc *sc, int if_id)
+{
+ struct ath_vap *avp;
+ struct ieee80211_hdr *wh;
+ struct ath_buf *bf;
+ struct sk_buff *skb;
+
+ avp = sc->sc_vaps[if_id];
+ ASSERT(avp);
+
+ /* Allocate a beacon descriptor if we haven't done so. */
+ if (!avp->av_bcbuf) {
+ /*
+ * Allocate beacon state for hostap/ibss. We know
+ * a buffer is available.
+ */
+
+ avp->av_bcbuf = list_first_entry(&sc->sc_bbuf,
+ struct ath_buf, list);
+ list_del(&avp->av_bcbuf->list);
+
+ if (sc->sc_opmode == ATH9K_M_HOSTAP ||
+ !(sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_VEOL)) {
+ int slot;
+ /*
+ * Assign the vap to a beacon xmit slot. As
+ * above, this cannot fail to find one.
+ */
+ avp->av_bslot = 0;
+ for (slot = 0; slot < ATH_BCBUF; slot++)
+ if (sc->sc_bslot[slot] == ATH_IF_ID_ANY) {
+ /*
+ * XXX hack, space out slots to better
+ * deal with misses
+ */
+ if (slot+1 < ATH_BCBUF &&
+ sc->sc_bslot[slot+1] ==
+ ATH_IF_ID_ANY) {
+ avp->av_bslot = slot+1;
+ break;
+ }
+ avp->av_bslot = slot;
+ /* NB: keep looking for a double slot */
+ }
+ BUG_ON(sc->sc_bslot[avp->av_bslot] != ATH_IF_ID_ANY);
+ sc->sc_bslot[avp->av_bslot] = if_id;
+ sc->sc_nbcnvaps++;
+ }
+ }
+
+ /* release the previous beacon frame , if it already exists. */
+ bf = avp->av_bcbuf;
+ if (bf->bf_mpdu != NULL) {
+ skb = (struct sk_buff *)bf->bf_mpdu;
+ ath_skb_unmap_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ dev_kfree_skb_any(skb);
+ bf->bf_mpdu = NULL;
+ }
+
+ /*
+ * NB: the beacon data buffer must be 32-bit aligned;
+ * we assume the wbuf routines will return us something
+ * with this alignment (perhaps should assert).
+ * FIXME: Fill avp->av_boff.bo_tim,avp->av_btxctl.txpower and
+ * avp->av_btxctl.shortPreamble
+ */
+ skb = ieee80211_beacon_get(sc->hw, avp->av_if_data);
+ if (skb == NULL) {
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: cannot get skb\n",
+ __func__);
+ return -ENOMEM;
+ }
+
+ /*
+ * Calculate a TSF adjustment factor required for
+ * staggered beacons. Note that we assume the format
+ * of the beacon frame leaves the tstamp field immediately
+ * following the header.
+ */
+ if (avp->av_bslot > 0) {
+ u64 tsfadjust;
+ __le64 val;
+ int intval;
+
+ /* FIXME: Use default value for now: Sujith */
+
+ intval = ATH_DEFAULT_BINTVAL;
+
+ /*
+ * The beacon interval is in TU's; the TSF in usecs.
+ * We figure out how many TU's to add to align the
+ * timestamp then convert to TSF units and handle
+ * byte swapping before writing it in the frame.
+ * The hardware will then add this each time a beacon
+ * frame is sent. Note that we align vap's 1..N
+ * and leave vap 0 untouched. This means vap 0
+ * has a timestamp in one beacon interval while the
+ * others get a timestamp aligned to the next interval.
+ */
+ tsfadjust = (intval * (ATH_BCBUF - avp->av_bslot)) / ATH_BCBUF;
+ val = cpu_to_le64(tsfadjust << 10); /* TU->TSF */
+
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: %s beacons, bslot %d intval %u tsfadjust %llu\n",
+ __func__, "stagger",
+ avp->av_bslot, intval, (unsigned long long)tsfadjust);
+
+ wh = (struct ieee80211_hdr *)skb->data;
+ memcpy(&wh[1], &val, sizeof(val));
+ }
+
+ bf->bf_buf_addr = ath_skb_map_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ bf->bf_mpdu = skb;
+
+ return 0;
+}
+
+/*
+ * Reclaim beacon resources and return buffer to the pool.
+ *
+ * Checks the VAP to put the beacon frame buffer back to the ATH object
+ * queue, and de-allocates any wbuf frames that were sent as CAB traffic.
+*/
+
+void ath_beacon_return(struct ath_softc *sc, struct ath_vap *avp)
+{
+ if (avp->av_bcbuf != NULL) {
+ struct ath_buf *bf;
+
+ if (avp->av_bslot != -1) {
+ sc->sc_bslot[avp->av_bslot] = ATH_IF_ID_ANY;
+ sc->sc_nbcnvaps--;
+ }
+
+ bf = avp->av_bcbuf;
+ if (bf->bf_mpdu != NULL) {
+ struct sk_buff *skb = (struct sk_buff *)bf->bf_mpdu;
+ ath_skb_unmap_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ dev_kfree_skb_any(skb);
+ bf->bf_mpdu = NULL;
+ }
+ list_add_tail(&bf->list, &sc->sc_bbuf);
+
+ avp->av_bcbuf = NULL;
+ }
+}
+
+/*
+ * Reclaim beacon resources and return buffer to the pool.
+ *
+ * This function will free any wbuf frames that are still attached to the
+ * beacon buffers in the ATH object. Note that this does not de-allocate
+ * any wbuf objects that are in the transmit queue and have not yet returned
+ * to the ATH object.
+*/
+
+void ath_beacon_free(struct ath_softc *sc)
+{
+ struct ath_buf *bf;
+
+ list_for_each_entry(bf, &sc->sc_bbuf, list) {
+ if (bf->bf_mpdu != NULL) {
+ struct sk_buff *skb = (struct sk_buff *) bf->bf_mpdu;
+ ath_skb_unmap_single(sc, skb, PCI_DMA_TODEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ dev_kfree_skb_any(skb);
+ bf->bf_mpdu = NULL;
+ }
+ }
+}
+
+/*
+ * Tasklet for Sending Beacons
+ *
+ * Transmit one or more beacon frames at SWBA. Dynamic updates to the frame
+ * contents are done as needed and the slot time is also adjusted based on
+ * current state.
+ *
+ * This tasklet is not scheduled, it's called in ISR context.
+*/
+
+void ath9k_beacon_tasklet(unsigned long data)
+{
+#define TSF_TO_TU(_h,_l) \
+ ((((u32)(_h)) << 22) | (((u32)(_l)) >> 10))
+
+ struct ath_softc *sc = (struct ath_softc *)data;
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf = NULL;
+ int slot, if_id;
+ u32 bfaddr;
+ u32 rx_clear = 0, rx_frame = 0, tx_frame = 0;
+ u32 show_cycles = 0;
+ u32 bc = 0; /* beacon count */
+ u64 tsf;
+ u32 tsftu;
+ u16 intval;
+
+ if (sc->sc_noreset) {
+ show_cycles = ath9k_hw_GetMibCycleCountsPct(ah,
+ &rx_clear,
+ &rx_frame,
+ &tx_frame);
+ }
+
+ /*
+ * Check if the previous beacon has gone out. If
+ * not don't try to post another, skip this period
+ * and wait for the next. Missed beacons indicate
+ * a problem and should not occur. If we miss too
+ * many consecutive beacons reset the device.
+ */
+ if (ath9k_hw_numtxpending(ah, sc->sc_bhalq) != 0) {
+ sc->sc_bmisscount++;
+ /* XXX: doth needs the chanchange IE countdown decremented.
+ * We should consider adding a mac80211 call to indicate
+ * a beacon miss so appropriate action could be taken
+ * (in that layer).
+ */
+ if (sc->sc_bmisscount < BSTUCK_THRESH) {
+ if (sc->sc_noreset) {
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: missed %u consecutive beacons\n",
+ __func__, sc->sc_bmisscount);
+ if (show_cycles) {
+ /*
+ * Display cycle counter stats
+ * from HW to aide in debug of
+ * stickiness.
+ */
+ DPRINTF(sc,
+ ATH_DBG_BEACON,
+ "%s: busy times: rx_clear=%d, "
+ "rx_frame=%d, tx_frame=%d\n",
+ __func__, rx_clear, rx_frame,
+ tx_frame);
+ } else {
+ DPRINTF(sc,
+ ATH_DBG_BEACON,
+ "%s: unable to obtain "
+ "busy times\n", __func__);
+ }
+ } else {
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: missed %u consecutive beacons\n",
+ __func__, sc->sc_bmisscount);
+ }
+ } else if (sc->sc_bmisscount >= BSTUCK_THRESH) {
+ if (sc->sc_noreset) {
+ if (sc->sc_bmisscount == BSTUCK_THRESH) {
+ DPRINTF(sc,
+ ATH_DBG_BEACON,
+ "%s: beacon is officially "
+ "stuck\n", __func__);
+ ath9k_hw_dmaRegDump(ah);
+ }
+ } else {
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: beacon is officially stuck\n",
+ __func__);
+ ath_bstuck_process(sc);
+ }
+ }
+
+ return;
+ }
+ if (sc->sc_bmisscount != 0) {
+ if (sc->sc_noreset) {
+ DPRINTF(sc,
+ ATH_DBG_BEACON,
+ "%s: resume beacon xmit after %u misses\n",
+ __func__, sc->sc_bmisscount);
+ } else {
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: resume beacon xmit after %u misses\n",
+ __func__, sc->sc_bmisscount);
+ }
+ sc->sc_bmisscount = 0;
+ }
+
+ /*
+ * Generate beacon frames. we are sending frames
+ * staggered so calculate the slot for this frame based
+ * on the tsf to safeguard against missing an swba.
+ */
+
+ /* FIXME: Use default value for now - Sujith */
+ intval = ATH_DEFAULT_BINTVAL;
+
+ tsf = ath9k_hw_gettsf64(ah);
+ tsftu = TSF_TO_TU(tsf>>32, tsf);
+ slot = ((tsftu % intval) * ATH_BCBUF) / intval;
+ if_id = sc->sc_bslot[(slot + 1) % ATH_BCBUF];
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: slot %d [tsf %llu tsftu %u intval %u] if_id %d\n",
+ __func__, slot, (unsigned long long) tsf, tsftu,
+ intval, if_id);
+ bfaddr = 0;
+ if (if_id != ATH_IF_ID_ANY) {
+ bf = ath_beacon_generate(sc, if_id);
+ if (bf != NULL) {
+ bfaddr = bf->bf_daddr;
+ bc = 1;
+ }
+ }
+ /*
+ * Handle slot time change when a non-ERP station joins/leaves
+ * an 11g network. The 802.11 layer notifies us via callback,
+ * we mark updateslot, then wait one beacon before effecting
+ * the change. This gives associated stations at least one
+ * beacon interval to note the state change.
+ *
+ * NB: The slot time change state machine is clocked according
+ * to whether we are bursting or staggering beacons. We
+ * recognize the request to update and record the current
+ * slot then don't transition until that slot is reached
+ * again. If we miss a beacon for that slot then we'll be
+ * slow to transition but we'll be sure at least one beacon
+ * interval has passed. When bursting slot is always left
+ * set to ATH_BCBUF so this check is a noop.
+ */
+ /* XXX locking */
+ if (sc->sc_updateslot == UPDATE) {
+ sc->sc_updateslot = COMMIT; /* commit next beacon */
+ sc->sc_slotupdate = slot;
+ } else if (sc->sc_updateslot == COMMIT && sc->sc_slotupdate == slot)
+ ath_setslottime(sc); /* commit change to hardware */
+
+ if (bfaddr != 0) {
+ /*
+ * Stop any current dma and put the new frame(s) on the queue.
+ * This should never fail since we check above that no frames
+ * are still pending on the queue.
+ */
+ if (!ath9k_hw_stoptxdma(ah, sc->sc_bhalq)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: beacon queue %u did not stop?\n",
+ __func__, sc->sc_bhalq);
+ /* NB: the HAL still stops DMA, so proceed */
+ }
+
+ /* NB: cabq traffic should already be queued and primed */
+ ath9k_hw_puttxbuf(ah, sc->sc_bhalq, bfaddr);
+ ath9k_hw_txstart(ah, sc->sc_bhalq);
+
+ sc->ast_be_xmit += bc; /* XXX per-vap? */
+ }
+#undef TSF_TO_TU
+}
+
+/*
+ * Tasklet for Beacon Stuck processing
+ *
+ * Processing for Beacon Stuck.
+ * Basically calls the ath_internal_reset function to reset the chip.
+*/
+
+void ath_bstuck_process(struct ath_softc *sc)
+{
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: stuck beacon; resetting (bmiss count %u)\n",
+ __func__, sc->sc_bmisscount);
+ ath_internal_reset(sc);
+}
+
+/*
+ * Configure the beacon and sleep timers.
+ *
+ * When operating as an AP this resets the TSF and sets
+ * up the hardware to notify us when we need to issue beacons.
+ *
+ * When operating in station mode this sets up the beacon
+ * timers according to the timestamp of the last received
+ * beacon and the current TSF, configures PCF and DTIM
+ * handling, programs the sleep registers so the hardware
+ * will wakeup in time to receive beacons, and configures
+ * the beacon miss handling so we'll receive a BMISS
+ * interrupt when we stop seeing beacons from the AP
+ * we've associated with.
+ */
+
+void ath_beacon_config(struct ath_softc *sc, int if_id)
+{
+#define TSF_TO_TU(_h,_l) \
+ ((((u32)(_h)) << 22) | (((u32)(_l)) >> 10))
+ struct ath_hal *ah = sc->sc_ah;
+ u32 nexttbtt, intval;
+ struct ath_beacon_config conf;
+ enum ath9k_opmode av_opmode;
+
+ if (if_id != ATH_IF_ID_ANY)
+ av_opmode = sc->sc_vaps[if_id]->av_opmode;
+ else
+ av_opmode = sc->sc_opmode;
+
+ memzero(&conf, sizeof(struct ath_beacon_config));
+
+ /* FIXME: Use default values for now - Sujith */
+ /* Query beacon configuration first */
+ /*
+ * Protocol stack doesn't support dynamic beacon configuration,
+ * use default configurations.
+ */
+ conf.beacon_interval = ATH_DEFAULT_BINTVAL;
+ conf.listen_interval = 1;
+ conf.dtim_period = conf.beacon_interval;
+ conf.dtim_count = 1;
+ conf.bmiss_timeout = ATH_DEFAULT_BMISS_LIMIT * conf.beacon_interval;
+
+ /* extract tstamp from last beacon and convert to TU */
+ nexttbtt = TSF_TO_TU(get_unaligned_le32(conf.u.last_tstamp + 4),
+ get_unaligned_le32(conf.u.last_tstamp));
+ /* XXX conditionalize multi-bss support? */
+ if (sc->sc_opmode == ATH9K_M_HOSTAP) {
+ /*
+ * For multi-bss ap support beacons are either staggered
+ * evenly over N slots or burst together. For the former
+ * arrange for the SWBA to be delivered for each slot.
+ * Slots that are not occupied will generate nothing.
+ */
+ /* NB: the beacon interval is kept internally in TU's */
+ intval = conf.beacon_interval & ATH9K_BEACON_PERIOD;
+ intval /= ATH_BCBUF; /* for staggered beacons */
+ } else {
+ intval = conf.beacon_interval & ATH9K_BEACON_PERIOD;
+ }
+
+ if (nexttbtt == 0) /* e.g. for ap mode */
+ nexttbtt = intval;
+ else if (intval) /* NB: can be 0 for monitor mode */
+ nexttbtt = roundup(nexttbtt, intval);
+ DPRINTF(sc, ATH_DBG_BEACON, "%s: nexttbtt %u intval %u (%u)\n",
+ __func__, nexttbtt, intval, conf.beacon_interval);
+ /* Check for ATH9K_M_HOSTAP and sc_nostabeacons for WDS client */
+ if (sc->sc_opmode == ATH9K_M_STA) {
+ struct ath9k_beacon_state bs;
+ u64 tsf;
+ u32 tsftu;
+ int dtimperiod, dtimcount, sleepduration;
+ int cfpperiod, cfpcount;
+
+ /*
+ * Setup dtim and cfp parameters according to
+ * last beacon we received (which may be none).
+ */
+ dtimperiod = conf.dtim_period;
+ if (dtimperiod <= 0) /* NB: 0 if not known */
+ dtimperiod = 1;
+ dtimcount = conf.dtim_count;
+ if (dtimcount >= dtimperiod) /* NB: sanity check */
+ dtimcount = 0; /* XXX? */
+ cfpperiod = 1; /* NB: no PCF support yet */
+ cfpcount = 0;
+
+ sleepduration = conf.listen_interval * intval;
+ if (sleepduration <= 0)
+ sleepduration = intval;
+
+#define FUDGE 2
+ /*
+ * Pull nexttbtt forward to reflect the current
+ * TSF and calculate dtim+cfp state for the result.
+ */
+ tsf = ath9k_hw_gettsf64(ah);
+ tsftu = TSF_TO_TU(tsf>>32, tsf) + FUDGE;
+ do {
+ nexttbtt += intval;
+ if (--dtimcount < 0) {
+ dtimcount = dtimperiod - 1;
+ if (--cfpcount < 0)
+ cfpcount = cfpperiod - 1;
+ }
+ } while (nexttbtt < tsftu);
+#undef FUDGE
+ memzero(&bs, sizeof(bs));
+ bs.bs_intval = intval;
+ bs.bs_nexttbtt = nexttbtt;
+ bs.bs_dtimperiod = dtimperiod*intval;
+ bs.bs_nextdtim = bs.bs_nexttbtt + dtimcount*intval;
+ bs.bs_cfpperiod = cfpperiod*bs.bs_dtimperiod;
+ bs.bs_cfpnext = bs.bs_nextdtim + cfpcount*bs.bs_dtimperiod;
+ bs.bs_cfpmaxduration = 0;
+ /*
+ * Calculate the number of consecutive beacons to miss
+ * before taking a BMISS interrupt. The configuration
+ * is specified in TU so we only need calculate based
+ * on the beacon interval. Note that we clamp the
+ * result to at most 15 beacons.
+ */
+ if (sleepduration > intval) {
+ bs.bs_bmissthreshold =
+ conf.listen_interval *
+ ATH_DEFAULT_BMISS_LIMIT / 2;
+ } else {
+ bs.bs_bmissthreshold =
+ DIV_ROUND_UP(conf.bmiss_timeout, intval);
+ if (bs.bs_bmissthreshold > 15)
+ bs.bs_bmissthreshold = 15;
+ else if (bs.bs_bmissthreshold <= 0)
+ bs.bs_bmissthreshold = 1;
+ }
+
+ /*
+ * Calculate sleep duration. The configuration is
+ * given in ms. We insure a multiple of the beacon
+ * period is used. Also, if the sleep duration is
+ * greater than the DTIM period then it makes senses
+ * to make it a multiple of that.
+ *
+ * XXX fixed at 100ms
+ */
+
+ bs.bs_sleepduration =
+ roundup(IEEE80211_MS_TO_TU(100), sleepduration);
+ if (bs.bs_sleepduration > bs.bs_dtimperiod)
+ bs.bs_sleepduration = bs.bs_dtimperiod;
+
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: tsf %llu "
+ "tsf:tu %u "
+ "intval %u "
+ "nexttbtt %u "
+ "dtim %u "
+ "nextdtim %u "
+ "bmiss %u "
+ "sleep %u "
+ "cfp:period %u "
+ "maxdur %u "
+ "next %u "
+ "timoffset %u\n"
+ , __func__
+ , (unsigned long long)tsf, tsftu
+ , bs.bs_intval
+ , bs.bs_nexttbtt
+ , bs.bs_dtimperiod
+ , bs.bs_nextdtim
+ , bs.bs_bmissthreshold
+ , bs.bs_sleepduration
+ , bs.bs_cfpperiod
+ , bs.bs_cfpmaxduration
+ , bs.bs_cfpnext
+ , bs.bs_timoffset
+ );
+
+ ath9k_hw_set_interrupts(ah, 0);
+ ath9k_hw_set_sta_beacon_timers(ah, &bs);
+ sc->sc_imask |= ATH9K_INT_BMISS;
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ } else {
+ u64 tsf;
+ u32 tsftu;
+ ath9k_hw_set_interrupts(ah, 0);
+ if (nexttbtt == intval)
+ intval |= ATH9K_BEACON_RESET_TSF;
+ if (sc->sc_opmode == ATH9K_M_IBSS) {
+ /*
+ * Pull nexttbtt forward to reflect the current
+ * TSF .
+ */
+#define FUDGE 2
+ if (!(intval & ATH9K_BEACON_RESET_TSF)) {
+ tsf = ath9k_hw_gettsf64(ah);
+ tsftu = TSF_TO_TU((u32)(tsf>>32),
+ (u32)tsf) + FUDGE;
+ do {
+ nexttbtt += intval;
+ } while (nexttbtt < tsftu);
+ }
+#undef FUDGE
+ DPRINTF(sc, ATH_DBG_BEACON,
+ "%s: IBSS nexttbtt %u intval %u (%u)\n",
+ __func__, nexttbtt,
+ intval & ~ATH9K_BEACON_RESET_TSF,
+ conf.beacon_interval);
+
+ /*
+ * In IBSS mode enable the beacon timers but only
+ * enable SWBA interrupts if we need to manually
+ * prepare beacon frames. Otherwise we use a
+ * self-linked tx descriptor and let the hardware
+ * deal with things.
+ */
+ intval |= ATH9K_BEACON_ENA;
+ if (!(ah->ah_caps.hw_caps & ATH9K_HW_CAP_VEOL))
+ sc->sc_imask |= ATH9K_INT_SWBA;
+ ath_beaconq_config(sc);
+ } else if (sc->sc_opmode == ATH9K_M_HOSTAP) {
+ /*
+ * In AP mode we enable the beacon timers and
+ * SWBA interrupts to prepare beacon frames.
+ */
+ intval |= ATH9K_BEACON_ENA;
+ sc->sc_imask |= ATH9K_INT_SWBA; /* beacon prepare */
+ ath_beaconq_config(sc);
+ }
+ ath9k_hw_beaconinit(ah, nexttbtt, intval);
+ sc->sc_bmisscount = 0;
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ /*
+ * When using a self-linked beacon descriptor in
+ * ibss mode load it once here.
+ */
+ if (sc->sc_opmode == ATH9K_M_IBSS &&
+ (ah->ah_caps.hw_caps & ATH9K_HW_CAP_VEOL))
+ ath_beacon_start_adhoc(sc, 0);
+ }
+#undef TSF_TO_TU
+}
+
+/* Function to collect beacon rssi data and resync beacon if necessary */
+
+void ath_beacon_sync(struct ath_softc *sc, int if_id)
+{
+ /*
+ * Resync beacon timers using the tsf of the
+ * beacon frame we just received.
+ */
+ ath_beacon_config(sc, if_id);
+ sc->sc_beacons = 1;
+}
--- /dev/null
+/*
+ * Copyright (c) 2008, Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+ /* Implementation of the main "ATH" layer. */
+
+#include "core.h"
+#include "regd.h"
+
+static int ath_outdoor; /* enable outdoor use */
+
+static const u8 ath_bcast_mac[ETH_ALEN] =
+ { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
+
+static u32 ath_chainmask_sel_up_rssi_thres =
+ ATH_CHAINMASK_SEL_UP_RSSI_THRES;
+static u32 ath_chainmask_sel_down_rssi_thres =
+ ATH_CHAINMASK_SEL_DOWN_RSSI_THRES;
+static u32 ath_chainmask_sel_period =
+ ATH_CHAINMASK_SEL_TIMEOUT;
+
+/* return bus cachesize in 4B word units */
+
+static void bus_read_cachesize(struct ath_softc *sc, int *csz)
+{
+ u8 u8tmp;
+
+ pci_read_config_byte(sc->pdev, PCI_CACHE_LINE_SIZE, (u8 *)&u8tmp);
+ *csz = (int)u8tmp;
+
+ /*
+ * This check was put in to avoid "unplesant" consequences if
+ * the bootrom has not fully initialized all PCI devices.
+ * Sometimes the cache line size register is not set
+ */
+
+ if (*csz == 0)
+ *csz = DEFAULT_CACHELINE >> 2; /* Use the default size */
+}
+
+/*
+ * Set current operating mode
+ *
+ * This function initializes and fills the rate table in the ATH object based
+ * on the operating mode. The blink rates are also set up here, although
+ * they have been superceeded by the ath_led module.
+*/
+
+static void ath_setcurmode(struct ath_softc *sc, enum wireless_mode mode)
+{
+ const struct ath9k_rate_table *rt;
+ int i;
+
+ memset(sc->sc_rixmap, 0xff, sizeof(sc->sc_rixmap));
+ rt = ath9k_hw_getratetable(sc->sc_ah, mode);
+ BUG_ON(!rt);
+
+ for (i = 0; i < rt->rateCount; i++)
+ sc->sc_rixmap[rt->info[i].rateCode] = (u8) i;
+
+ memzero(sc->sc_hwmap, sizeof(sc->sc_hwmap));
+ for (i = 0; i < 256; i++) {
+ u8 ix = rt->rateCodeToIndex[i];
+
+ if (ix == 0xff)
+ continue;
+
+ sc->sc_hwmap[i].ieeerate =
+ rt->info[ix].dot11Rate & IEEE80211_RATE_VAL;
+ sc->sc_hwmap[i].rateKbps = rt->info[ix].rateKbps;
+
+ if (rt->info[ix].shortPreamble ||
+ rt->info[ix].phy == PHY_OFDM) {
+ /* XXX: Handle this */
+ }
+
+ /* NB: this uses the last entry if the rate isn't found */
+ /* XXX beware of overlow */
+ }
+ sc->sc_currates = rt;
+ sc->sc_curmode = mode;
+ /*
+ * All protection frames are transmited at 2Mb/s for
+ * 11g, otherwise at 1Mb/s.
+ * XXX select protection rate index from rate table.
+ */
+ sc->sc_protrix = (mode == ATH9K_MODE_11G ? 1 : 0);
+}
+
+/*
+ * Set up rate table (legacy rates)
+ */
+static void ath_setup_rates(struct ath_softc *sc, enum ieee80211_band band)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ const struct ath9k_rate_table *rt = NULL;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_rate *rate;
+ int i, maxrates;
+
+ switch (band) {
+ case IEEE80211_BAND_2GHZ:
+ rt = ath9k_hw_getratetable(ah, ATH9K_MODE_11G);
+ break;
+ case IEEE80211_BAND_5GHZ:
+ rt = ath9k_hw_getratetable(ah, ATH9K_MODE_11A);
+ break;
+ default:
+ break;
+ }
+
+ if (rt == NULL)
+ return;
+
+ sband = &sc->sbands[band];
+ rate = sc->rates[band];
+
+ if (rt->rateCount > ATH_RATE_MAX)
+ maxrates = ATH_RATE_MAX;
+ else
+ maxrates = rt->rateCount;
+
+ for (i = 0; i < maxrates; i++) {
+ rate[i].bitrate = rt->info[i].rateKbps / 100;
+ rate[i].hw_value = rt->info[i].rateCode;
+ sband->n_bitrates++;
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Rate: %2dMbps, ratecode: %2d\n",
+ __func__,
+ rate[i].bitrate / 10,
+ rate[i].hw_value);
+ }
+}
+
+/*
+ * Set up channel list
+ */
+static int ath_setup_channels(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int nchan, i, a = 0, b = 0;
+ u8 regclassids[ATH_REGCLASSIDS_MAX];
+ u32 nregclass = 0;
+ struct ieee80211_supported_band *band_2ghz;
+ struct ieee80211_supported_band *band_5ghz;
+ struct ieee80211_channel *chan_2ghz;
+ struct ieee80211_channel *chan_5ghz;
+ struct ath9k_channel *c;
+
+ /* Fill in ah->ah_channels */
+ if (!ath9k_regd_init_channels(ah,
+ ATH_CHAN_MAX,
+ (u32 *)&nchan,
+ regclassids,
+ ATH_REGCLASSIDS_MAX,
+ &nregclass,
+ CTRY_DEFAULT,
+ false,
+ 1)) {
+ u32 rd = ah->ah_currentRD;
+
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to collect channel list; "
+ "regdomain likely %u country code %u\n",
+ __func__, rd, CTRY_DEFAULT);
+ return -EINVAL;
+ }
+
+ band_2ghz = &sc->sbands[IEEE80211_BAND_2GHZ];
+ band_5ghz = &sc->sbands[IEEE80211_BAND_5GHZ];
+ chan_2ghz = sc->channels[IEEE80211_BAND_2GHZ];
+ chan_5ghz = sc->channels[IEEE80211_BAND_5GHZ];
+
+ for (i = 0; i < nchan; i++) {
+ c = &ah->ah_channels[i];
+ if (IS_CHAN_2GHZ(c)) {
+ chan_2ghz[a].band = IEEE80211_BAND_2GHZ;
+ chan_2ghz[a].center_freq = c->channel;
+ chan_2ghz[a].max_power = c->maxTxPower;
+
+ if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
+ chan_2ghz[a].flags |=
+ IEEE80211_CHAN_NO_IBSS;
+ if (c->channelFlags & CHANNEL_PASSIVE)
+ chan_2ghz[a].flags |=
+ IEEE80211_CHAN_PASSIVE_SCAN;
+
+ band_2ghz->n_channels = ++a;
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: 2MHz channel: %d, "
+ "channelFlags: 0x%x\n",
+ __func__,
+ c->channel,
+ c->channelFlags);
+ } else if (IS_CHAN_5GHZ(c)) {
+ chan_5ghz[b].band = IEEE80211_BAND_5GHZ;
+ chan_5ghz[b].center_freq = c->channel;
+ chan_5ghz[b].max_power = c->maxTxPower;
+
+ if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
+ chan_5ghz[b].flags |=
+ IEEE80211_CHAN_NO_IBSS;
+ if (c->channelFlags & CHANNEL_PASSIVE)
+ chan_5ghz[b].flags |=
+ IEEE80211_CHAN_PASSIVE_SCAN;
+
+ band_5ghz->n_channels = ++b;
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: 5MHz channel: %d, "
+ "channelFlags: 0x%x\n",
+ __func__,
+ c->channel,
+ c->channelFlags);
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * Determine mode from channel flags
+ *
+ * This routine will provide the enumerated WIRELESSS_MODE value based
+ * on the settings of the channel flags. If ho valid set of flags
+ * exist, the lowest mode (11b) is selected.
+*/
+
+static enum wireless_mode ath_chan2mode(struct ath9k_channel *chan)
+{
+ if (chan->chanmode == CHANNEL_A)
+ return ATH9K_MODE_11A;
+ else if (chan->chanmode == CHANNEL_G)
+ return ATH9K_MODE_11G;
+ else if (chan->chanmode == CHANNEL_B)
+ return ATH9K_MODE_11B;
+ else if (chan->chanmode == CHANNEL_A_HT20)
+ return ATH9K_MODE_11NA_HT20;
+ else if (chan->chanmode == CHANNEL_G_HT20)
+ return ATH9K_MODE_11NG_HT20;
+ else if (chan->chanmode == CHANNEL_A_HT40PLUS)
+ return ATH9K_MODE_11NA_HT40PLUS;
+ else if (chan->chanmode == CHANNEL_A_HT40MINUS)
+ return ATH9K_MODE_11NA_HT40MINUS;
+ else if (chan->chanmode == CHANNEL_G_HT40PLUS)
+ return ATH9K_MODE_11NG_HT40PLUS;
+ else if (chan->chanmode == CHANNEL_G_HT40MINUS)
+ return ATH9K_MODE_11NG_HT40MINUS;
+
+ /* NB: should not get here */
+ return ATH9K_MODE_11B;
+}
+
+/*
+ * Stop the device, grabbing the top-level lock to protect
+ * against concurrent entry through ath_init (which can happen
+ * if another thread does a system call and the thread doing the
+ * stop is preempted).
+ */
+
+static int ath_stop(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: invalid %u\n",
+ __func__, sc->sc_invalid);
+
+ /*
+ * Shutdown the hardware and driver:
+ * stop output from above
+ * reset 802.11 state machine
+ * (sends station deassoc/deauth frames)
+ * turn off timers
+ * disable interrupts
+ * clear transmit machinery
+ * clear receive machinery
+ * turn off the radio
+ * reclaim beacon resources
+ *
+ * Note that some of this work is not possible if the
+ * hardware is gone (invalid).
+ */
+
+ if (!sc->sc_invalid)
+ ath9k_hw_set_interrupts(ah, 0);
+ ath_draintxq(sc, false);
+ if (!sc->sc_invalid) {
+ ath_stoprecv(sc);
+ ath9k_hw_phy_disable(ah);
+ } else
+ sc->sc_rxlink = NULL;
+
+ return 0;
+}
+
+/*
+ * Start Scan
+ *
+ * This function is called when starting a channel scan. It will perform
+ * power save wakeup processing, set the filter for the scan, and get the
+ * chip ready to send broadcast packets out during the scan.
+*/
+
+void ath_scan_start(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u32 rfilt;
+ u32 now = (u32) jiffies_to_msecs(get_timestamp());
+
+ sc->sc_scanning = 1;
+ rfilt = ath_calcrxfilter(sc);
+ ath9k_hw_setrxfilter(ah, rfilt);
+ ath9k_hw_write_associd(ah, ath_bcast_mac, 0);
+
+ /* Restore previous power management state. */
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%d.%03d | %s: RX filter 0x%x aid 0\n",
+ now / 1000, now % 1000, __func__, rfilt);
+}
+
+/*
+ * Scan End
+ *
+ * This routine is called by the upper layer when the scan is completed. This
+ * will set the filters back to normal operating mode, set the BSSID to the
+ * correct value, and restore the power save state.
+*/
+
+void ath_scan_end(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u32 rfilt;
+ u32 now = (u32) jiffies_to_msecs(get_timestamp());
+
+ sc->sc_scanning = 0;
+ /* Request for a full reset due to rx packet filter changes */
+ sc->sc_full_reset = 1;
+ rfilt = ath_calcrxfilter(sc);
+ ath9k_hw_setrxfilter(ah, rfilt);
+ ath9k_hw_write_associd(ah, sc->sc_curbssid, sc->sc_curaid);
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%d.%03d | %s: RX filter 0x%x aid 0x%x\n",
+ now / 1000, now % 1000, __func__, rfilt, sc->sc_curaid);
+}
+
+/*
+ * Set the current channel
+ *
+ * Set/change channels. If the channel is really being changed, it's done
+ * by reseting the chip. To accomplish this we must first cleanup any pending
+ * DMA, then restart stuff after a la ath_init.
+*/
+int ath_set_channel(struct ath_softc *sc, struct ath9k_channel *hchan)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ bool fastcc = true, stopped;
+ enum ath9k_ht_macmode ht_macmode;
+
+ if (sc->sc_invalid) /* if the device is invalid or removed */
+ return -EIO;
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: %u (%u MHz) -> %u (%u MHz), cflags:%x\n",
+ __func__,
+ ath9k_hw_mhz2ieee(ah, sc->sc_curchan.channel,
+ sc->sc_curchan.channelFlags),
+ sc->sc_curchan.channel,
+ ath9k_hw_mhz2ieee(ah, hchan->channel, hchan->channelFlags),
+ hchan->channel, hchan->channelFlags);
+
+ ht_macmode = ath_cwm_macmode(sc);
+
+ if (hchan->channel != sc->sc_curchan.channel ||
+ hchan->channelFlags != sc->sc_curchan.channelFlags ||
+ sc->sc_update_chainmask || sc->sc_full_reset) {
+ int status;
+ /*
+ * This is only performed if the channel settings have
+ * actually changed.
+ *
+ * To switch channels clear any pending DMA operations;
+ * wait long enough for the RX fifo to drain, reset the
+ * hardware at the new frequency, and then re-enable
+ * the relevant bits of the h/w.
+ */
+ ath9k_hw_set_interrupts(ah, 0); /* disable interrupts */
+ ath_draintxq(sc, false); /* clear pending tx frames */
+ stopped = ath_stoprecv(sc); /* turn off frame recv */
+
+ /* XXX: do not flush receive queue here. We don't want
+ * to flush data frames already in queue because of
+ * changing channel. */
+
+ if (!stopped || sc->sc_full_reset)
+ fastcc = false;
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, sc->sc_opmode, hchan,
+ ht_macmode, sc->sc_tx_chainmask,
+ sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing,
+ fastcc, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset channel %u (%uMhz) "
+ "flags 0x%x hal status %u\n", __func__,
+ ath9k_hw_mhz2ieee(ah, hchan->channel,
+ hchan->channelFlags),
+ hchan->channel, hchan->channelFlags, status);
+ spin_unlock_bh(&sc->sc_resetlock);
+ return -EIO;
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ sc->sc_curchan = *hchan;
+ sc->sc_update_chainmask = 0;
+ sc->sc_full_reset = 0;
+
+ /* Re-enable rx framework */
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to restart recv logic\n", __func__);
+ return -EIO;
+ }
+ /*
+ * Change channels and update the h/w rate map
+ * if we're switching; e.g. 11a to 11b/g.
+ */
+ ath_setcurmode(sc, ath_chan2mode(hchan));
+
+ ath_update_txpow(sc); /* update tx power state */
+ /*
+ * Re-enable interrupts.
+ */
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ }
+ return 0;
+}
+
+/**********************/
+/* Chainmask Handling */
+/**********************/
+
+static void ath_chainmask_sel_timertimeout(unsigned long data)
+{
+ struct ath_chainmask_sel *cm = (struct ath_chainmask_sel *)data;
+ cm->switch_allowed = 1;
+}
+
+/* Start chainmask select timer */
+static void ath_chainmask_sel_timerstart(struct ath_chainmask_sel *cm)
+{
+ cm->switch_allowed = 0;
+ mod_timer(&cm->timer, ath_chainmask_sel_period);
+}
+
+/* Stop chainmask select timer */
+static void ath_chainmask_sel_timerstop(struct ath_chainmask_sel *cm)
+{
+ cm->switch_allowed = 0;
+ del_timer_sync(&cm->timer);
+}
+
+static void ath_chainmask_sel_init(struct ath_softc *sc, struct ath_node *an)
+{
+ struct ath_chainmask_sel *cm = &an->an_chainmask_sel;
+
+ memzero(cm, sizeof(struct ath_chainmask_sel));
+
+ cm->cur_tx_mask = sc->sc_tx_chainmask;
+ cm->cur_rx_mask = sc->sc_rx_chainmask;
+ cm->tx_avgrssi = ATH_RSSI_DUMMY_MARKER;
+ setup_timer(&cm->timer,
+ ath_chainmask_sel_timertimeout, (unsigned long) cm);
+}
+
+int ath_chainmask_sel_logic(struct ath_softc *sc, struct ath_node *an)
+{
+ struct ath_chainmask_sel *cm = &an->an_chainmask_sel;
+
+ /*
+ * Disable auto-swtiching in one of the following if conditions.
+ * sc_chainmask_auto_sel is used for internal global auto-switching
+ * enabled/disabled setting
+ */
+ if (sc->sc_ah->ah_caps.tx_chainmask != ATH_CHAINMASK_SEL_3X3) {
+ cm->cur_tx_mask = sc->sc_tx_chainmask;
+ return cm->cur_tx_mask;
+ }
+
+ if (cm->tx_avgrssi == ATH_RSSI_DUMMY_MARKER)
+ return cm->cur_tx_mask;
+
+ if (cm->switch_allowed) {
+ /* Switch down from tx 3 to tx 2. */
+ if (cm->cur_tx_mask == ATH_CHAINMASK_SEL_3X3 &&
+ ATH_RSSI_OUT(cm->tx_avgrssi) >=
+ ath_chainmask_sel_down_rssi_thres) {
+ cm->cur_tx_mask = sc->sc_tx_chainmask;
+
+ /* Don't let another switch happen until
+ * this timer expires */
+ ath_chainmask_sel_timerstart(cm);
+ }
+ /* Switch up from tx 2 to 3. */
+ else if (cm->cur_tx_mask == sc->sc_tx_chainmask &&
+ ATH_RSSI_OUT(cm->tx_avgrssi) <=
+ ath_chainmask_sel_up_rssi_thres) {
+ cm->cur_tx_mask = ATH_CHAINMASK_SEL_3X3;
+
+ /* Don't let another switch happen
+ * until this timer expires */
+ ath_chainmask_sel_timerstart(cm);
+ }
+ }
+
+ return cm->cur_tx_mask;
+}
+
+/*
+ * Update tx/rx chainmask. For legacy association,
+ * hard code chainmask to 1x1, for 11n association, use
+ * the chainmask configuration.
+ */
+
+void ath_update_chainmask(struct ath_softc *sc, int is_ht)
+{
+ sc->sc_update_chainmask = 1;
+ if (is_ht) {
+ sc->sc_tx_chainmask = sc->sc_ah->ah_caps.tx_chainmask;
+ sc->sc_rx_chainmask = sc->sc_ah->ah_caps.rx_chainmask;
+ } else {
+ sc->sc_tx_chainmask = 1;
+ sc->sc_rx_chainmask = 1;
+ }
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: tx chmask: %d, rx chmask: %d\n",
+ __func__, sc->sc_tx_chainmask, sc->sc_rx_chainmask);
+}
+
+/******************/
+/* VAP management */
+/******************/
+
+/*
+ * VAP in Listen mode
+ *
+ * This routine brings the VAP out of the down state into a "listen" state
+ * where it waits for association requests. This is used in AP and AdHoc
+ * modes.
+*/
+
+int ath_vap_listen(struct ath_softc *sc, int if_id)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_vap *avp;
+ u32 rfilt = 0;
+ DECLARE_MAC_BUF(mac);
+
+ avp = sc->sc_vaps[if_id];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: invalid interface id %u\n",
+ __func__, if_id);
+ return -EINVAL;
+ }
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ ath_slow_ant_div_stop(&sc->sc_antdiv);
+#endif
+
+ /* update ratectrl about the new state */
+ ath_rate_newstate(sc, avp);
+
+ rfilt = ath_calcrxfilter(sc);
+ ath9k_hw_setrxfilter(ah, rfilt);
+
+ if (sc->sc_opmode == ATH9K_M_STA || sc->sc_opmode == ATH9K_M_IBSS) {
+ memcpy(sc->sc_curbssid, ath_bcast_mac, ETH_ALEN);
+ ath9k_hw_write_associd(ah, sc->sc_curbssid, sc->sc_curaid);
+ } else
+ sc->sc_curaid = 0;
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: RX filter 0x%x bssid %s aid 0x%x\n",
+ __func__, rfilt, print_mac(mac,
+ sc->sc_curbssid), sc->sc_curaid);
+
+ /*
+ * XXXX
+ * Disable BMISS interrupt when we're not associated
+ */
+ ath9k_hw_set_interrupts(ah,
+ sc->sc_imask & ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS));
+ sc->sc_imask &= ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS);
+ /* need to reconfigure the beacons when it moves to RUN */
+ sc->sc_beacons = 0;
+
+ return 0;
+}
+
+int ath_vap_attach(struct ath_softc *sc,
+ int if_id,
+ struct ieee80211_vif *if_data,
+ enum ath9k_opmode opmode)
+{
+ struct ath_vap *avp;
+
+ if (if_id >= ATH_BCBUF || sc->sc_vaps[if_id] != NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Invalid interface id = %u\n", __func__, if_id);
+ return -EINVAL;
+ }
+
+ switch (opmode) {
+ case ATH9K_M_STA:
+ case ATH9K_M_IBSS:
+ case ATH9K_M_MONITOR:
+ break;
+ case ATH9K_M_HOSTAP:
+ /* XXX not right, beacon buffer is allocated on RUN trans */
+ if (list_empty(&sc->sc_bbuf))
+ return -ENOMEM;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* create ath_vap */
+ avp = kmalloc(sizeof(struct ath_vap), GFP_KERNEL);
+ if (avp == NULL)
+ return -ENOMEM;
+
+ memzero(avp, sizeof(struct ath_vap));
+ avp->av_if_data = if_data;
+ /* Set the VAP opmode */
+ avp->av_opmode = opmode;
+ avp->av_bslot = -1;
+ INIT_LIST_HEAD(&avp->av_mcastq.axq_q);
+ INIT_LIST_HEAD(&avp->av_mcastq.axq_acq);
+ spin_lock_init(&avp->av_mcastq.axq_lock);
+
+ ath9k_hw_set_tsfadjust(sc->sc_ah, 1);
+
+ sc->sc_vaps[if_id] = avp;
+ sc->sc_nvaps++;
+ /* Set the device opmode */
+ sc->sc_opmode = opmode;
+
+ /* default VAP configuration */
+ avp->av_config.av_fixed_rateset = IEEE80211_FIXED_RATE_NONE;
+ avp->av_config.av_fixed_retryset = 0x03030303;
+
+ return 0;
+}
+
+int ath_vap_detach(struct ath_softc *sc, int if_id)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_vap *avp;
+
+ avp = sc->sc_vaps[if_id];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: invalid interface id %u\n",
+ __func__, if_id);
+ return -EINVAL;
+ }
+
+ /*
+ * Quiesce the hardware while we remove the vap. In
+ * particular we need to reclaim all references to the
+ * vap state by any frames pending on the tx queues.
+ *
+ * XXX can we do this w/o affecting other vap's?
+ */
+ ath9k_hw_set_interrupts(ah, 0); /* disable interrupts */
+ ath_draintxq(sc, false); /* stop xmit side */
+ ath_stoprecv(sc); /* stop recv side */
+ ath_flushrecv(sc); /* flush recv queue */
+
+ /* Reclaim any pending mcast bufs on the vap. */
+ ath_tx_draintxq(sc, &avp->av_mcastq, false);
+
+ kfree(avp);
+ sc->sc_vaps[if_id] = NULL;
+ sc->sc_nvaps--;
+
+ return 0;
+}
+
+int ath_vap_config(struct ath_softc *sc,
+ int if_id, struct ath_vap_config *if_config)
+{
+ struct ath_vap *avp;
+
+ if (if_id >= ATH_BCBUF) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Invalid interface id = %u\n", __func__, if_id);
+ return -EINVAL;
+ }
+
+ avp = sc->sc_vaps[if_id];
+ ASSERT(avp != NULL);
+
+ if (avp)
+ memcpy(&avp->av_config, if_config, sizeof(avp->av_config));
+
+ return 0;
+}
+
+/********/
+/* Core */
+/********/
+
+int ath_open(struct ath_softc *sc, struct ath9k_channel *initial_chan)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int status;
+ int error = 0;
+ enum ath9k_ht_macmode ht_macmode = ath_cwm_macmode(sc);
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: mode %d\n", __func__, sc->sc_opmode);
+
+ /*
+ * Stop anything previously setup. This is safe
+ * whether this is the first time through or not.
+ */
+ ath_stop(sc);
+
+ /* Initialize chanmask selection */
+ sc->sc_tx_chainmask = ah->ah_caps.tx_chainmask;
+ sc->sc_rx_chainmask = ah->ah_caps.rx_chainmask;
+
+ /* Reset SERDES registers */
+ ath9k_hw_configpcipowersave(ah, 0);
+
+ /*
+ * The basic interface to setting the hardware in a good
+ * state is ``reset''. On return the hardware is known to
+ * be powered up and with interrupts disabled. This must
+ * be followed by initialization of the appropriate bits
+ * and then setup of the interrupt mask.
+ */
+ sc->sc_curchan = *initial_chan;
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, sc->sc_opmode, &sc->sc_curchan, ht_macmode,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, false, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset hardware; hal status %u "
+ "(freq %u flags 0x%x)\n", __func__, status,
+ sc->sc_curchan.channel, sc->sc_curchan.channelFlags);
+ error = -EIO;
+ spin_unlock_bh(&sc->sc_resetlock);
+ goto done;
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+ /*
+ * This is needed only to setup initial state
+ * but it's best done after a reset.
+ */
+ ath_update_txpow(sc);
+
+ /*
+ * Setup the hardware after reset:
+ * The receive engine is set going.
+ * Frame transmit is handled entirely
+ * in the frame output path; there's nothing to do
+ * here except setup the interrupt mask.
+ */
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to start recv logic\n", __func__);
+ error = -EIO;
+ goto done;
+ }
+ /* Setup our intr mask. */
+ sc->sc_imask = ATH9K_INT_RX | ATH9K_INT_TX
+ | ATH9K_INT_RXEOL | ATH9K_INT_RXORN
+ | ATH9K_INT_FATAL | ATH9K_INT_GLOBAL;
+
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_GTT)
+ sc->sc_imask |= ATH9K_INT_GTT;
+
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ sc->sc_imask |= ATH9K_INT_CST;
+
+ /*
+ * Enable MIB interrupts when there are hardware phy counters.
+ * Note we only do this (at the moment) for station mode.
+ */
+ if (ath9k_hw_phycounters(ah) &&
+ ((sc->sc_opmode == ATH9K_M_STA) || (sc->sc_opmode == ATH9K_M_IBSS)))
+ sc->sc_imask |= ATH9K_INT_MIB;
+ /*
+ * Some hardware processes the TIM IE and fires an
+ * interrupt when the TIM bit is set. For hardware
+ * that does, if not overridden by configuration,
+ * enable the TIM interrupt when operating as station.
+ */
+ if ((ah->ah_caps.hw_caps & ATH9K_HW_CAP_ENHANCEDPM) &&
+ (sc->sc_opmode == ATH9K_M_STA) &&
+ !sc->sc_config.swBeaconProcess)
+ sc->sc_imask |= ATH9K_INT_TIM;
+ /*
+ * Don't enable interrupts here as we've not yet built our
+ * vap and node data structures, which will be needed as soon
+ * as we start receiving.
+ */
+ ath_setcurmode(sc, ath_chan2mode(initial_chan));
+
+ /* XXX: we must make sure h/w is ready and clear invalid flag
+ * before turning on interrupt. */
+ sc->sc_invalid = 0;
+done:
+ return error;
+}
+
+/*
+ * Reset the hardware w/o losing operational state. This is
+ * basically a more efficient way of doing ath_stop, ath_init,
+ * followed by state transitions to the current 802.11
+ * operational state. Used to recover from errors rx overrun
+ * and to reset the hardware when rf gain settings must be reset.
+ */
+
+static int ath_reset_start(struct ath_softc *sc, u32 flag)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ ath9k_hw_set_interrupts(ah, 0); /* disable interrupts */
+ ath_draintxq(sc, flag & RESET_RETRY_TXQ); /* stop xmit side */
+ ath_stoprecv(sc); /* stop recv side */
+ ath_flushrecv(sc); /* flush recv queue */
+
+ return 0;
+}
+
+static int ath_reset_end(struct ath_softc *sc, u32 flag)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ if (ath_startrecv(sc) != 0) /* restart recv */
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to start recv logic\n", __func__);
+
+ /*
+ * We may be doing a reset in response to a request
+ * that changes the channel so update any state that
+ * might change as a result.
+ */
+ ath_setcurmode(sc, ath_chan2mode(&sc->sc_curchan));
+
+ ath_update_txpow(sc); /* update tx power state */
+
+ if (sc->sc_beacons)
+ ath_beacon_config(sc, ATH_IF_ID_ANY); /* restart beacons */
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+
+ /* Restart the txq */
+ if (flag & RESET_RETRY_TXQ) {
+ int i;
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i)) {
+ spin_lock_bh(&sc->sc_txq[i].axq_lock);
+ ath_txq_schedule(sc, &sc->sc_txq[i]);
+ spin_unlock_bh(&sc->sc_txq[i].axq_lock);
+ }
+ }
+ }
+ return 0;
+}
+
+int ath_reset(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int status;
+ int error = 0;
+ enum ath9k_ht_macmode ht_macmode = ath_cwm_macmode(sc);
+
+ /* NB: indicate channel change so we do a full reset */
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, sc->sc_opmode, &sc->sc_curchan,
+ ht_macmode,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, false, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset hardware; hal status %u\n",
+ __func__, status);
+ error = -EIO;
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ return error;
+}
+
+int ath_suspend(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ /* No I/O if device has been surprise removed */
+ if (sc->sc_invalid)
+ return -EIO;
+
+ /* Shut off the interrupt before setting sc->sc_invalid to '1' */
+ ath9k_hw_set_interrupts(ah, 0);
+
+ /* XXX: we must make sure h/w will not generate any interrupt
+ * before setting the invalid flag. */
+ sc->sc_invalid = 1;
+
+ /* disable HAL and put h/w to sleep */
+ ath9k_hw_disable(sc->sc_ah);
+
+ ath9k_hw_configpcipowersave(sc->sc_ah, 1);
+
+ return 0;
+}
+
+/* Interrupt handler. Most of the actual processing is deferred.
+ * It's the caller's responsibility to ensure the chip is awake. */
+
+irqreturn_t ath_isr(int irq, void *dev)
+{
+ struct ath_softc *sc = dev;
+ struct ath_hal *ah = sc->sc_ah;
+ enum ath9k_int status;
+ bool sched = false;
+
+ do {
+ if (sc->sc_invalid) {
+ /*
+ * The hardware is not ready/present, don't
+ * touch anything. Note this can happen early
+ * on if the IRQ is shared.
+ */
+ return IRQ_NONE;
+ }
+ if (!ath9k_hw_intrpend(ah)) { /* shared irq, not for us */
+ return IRQ_NONE;
+ }
+
+ /*
+ * Figure out the reason(s) for the interrupt. Note
+ * that the hal returns a pseudo-ISR that may include
+ * bits we haven't explicitly enabled so we mask the
+ * value to insure we only process bits we requested.
+ */
+ ath9k_hw_getisr(ah, &status); /* NB: clears ISR too */
+
+ status &= sc->sc_imask; /* discard unasked-for bits */
+
+ /*
+ * If there are no status bits set, then this interrupt was not
+ * for me (should have been caught above).
+ */
+
+ if (!status)
+ return IRQ_NONE;
+
+ sc->sc_intrstatus = status;
+
+ if (status & ATH9K_INT_FATAL) {
+ /* need a chip reset */
+ sched = true;
+ } else if (status & ATH9K_INT_RXORN) {
+ /* need a chip reset */
+ sched = true;
+ } else {
+ if (status & ATH9K_INT_SWBA) {
+ /* schedule a tasklet for beacon handling */
+ tasklet_schedule(&sc->bcon_tasklet);
+ }
+ if (status & ATH9K_INT_RXEOL) {
+ /*
+ * NB: the hardware should re-read the link when
+ * RXE bit is written, but it doesn't work
+ * at least on older hardware revs.
+ */
+ sched = true;
+ }
+
+ if (status & ATH9K_INT_TXURN)
+ /* bump tx trigger level */
+ ath9k_hw_updatetxtriglevel(ah, true);
+ /* XXX: optimize this */
+ if (status & ATH9K_INT_RX)
+ sched = true;
+ if (status & ATH9K_INT_TX)
+ sched = true;
+ if (status & ATH9K_INT_BMISS)
+ sched = true;
+ /* carrier sense timeout */
+ if (status & ATH9K_INT_CST)
+ sched = true;
+ if (status & ATH9K_INT_MIB) {
+ /*
+ * Disable interrupts until we service the MIB
+ * interrupt; otherwise it will continue to
+ * fire.
+ */
+ ath9k_hw_set_interrupts(ah, 0);
+ /*
+ * Let the hal handle the event. We assume
+ * it will clear whatever condition caused
+ * the interrupt.
+ */
+ ath9k_hw_procmibevent(ah, &sc->sc_halstats);
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ }
+ if (status & ATH9K_INT_TIM_TIMER) {
+ if (!(ah->ah_caps.hw_caps &
+ ATH9K_HW_CAP_AUTOSLEEP)) {
+ /* Clear RxAbort bit so that we can
+ * receive frames */
+ ath9k_hw_setrxabort(ah, 0);
+ sched = true;
+ }
+ }
+ }
+ } while (0);
+
+ if (sched) {
+ /* turn off every interrupt except SWBA */
+ ath9k_hw_set_interrupts(ah, (sc->sc_imask & ATH9K_INT_SWBA));
+ tasklet_schedule(&sc->intr_tq);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/* Deferred interrupt processing */
+
+static void ath9k_tasklet(unsigned long data)
+{
+ struct ath_softc *sc = (struct ath_softc *)data;
+ u32 status = sc->sc_intrstatus;
+
+ if (status & ATH9K_INT_FATAL) {
+ /* need a chip reset */
+ ath_internal_reset(sc);
+ return;
+ } else {
+
+ if (status &
+ (ATH9K_INT_RX | ATH9K_INT_RXEOL | ATH9K_INT_RXORN)) {
+ /* XXX: fill me in */
+ /*
+ if (status & ATH9K_INT_RXORN) {
+ }
+ if (status & ATH9K_INT_RXEOL) {
+ }
+ */
+ spin_lock_bh(&sc->sc_rxflushlock);
+ ath_rx_tasklet(sc, 0);
+ spin_unlock_bh(&sc->sc_rxflushlock);
+ }
+ /* XXX: optimize this */
+ if (status & ATH9K_INT_TX)
+ ath_tx_tasklet(sc);
+ /* XXX: fill me in */
+ /*
+ if (status & ATH9K_INT_BMISS) {
+ }
+ if (status & (ATH9K_INT_TIM | ATH9K_INT_DTIMSYNC)) {
+ if (status & ATH9K_INT_TIM) {
+ }
+ if (status & ATH9K_INT_DTIMSYNC) {
+ }
+ }
+ */
+ }
+
+ /* re-enable hardware interrupt */
+ ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask);
+}
+
+int ath_init(u16 devid, struct ath_softc *sc)
+{
+ struct ath_hal *ah = NULL;
+ int status;
+ int error = 0, i;
+ int csz = 0;
+ u32 rd;
+
+ /* XXX: hardware will not be ready until ath_open() being called */
+ sc->sc_invalid = 1;
+
+ sc->sc_debug = DBG_DEFAULT;
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: devid 0x%x\n", __func__, devid);
+
+ /* Initialize tasklet */
+ tasklet_init(&sc->intr_tq, ath9k_tasklet, (unsigned long)sc);
+ tasklet_init(&sc->bcon_tasklet, ath9k_beacon_tasklet,
+ (unsigned long)sc);
+
+ /*
+ * Cache line size is used to size and align various
+ * structures used to communicate with the hardware.
+ */
+ bus_read_cachesize(sc, &csz);
+ /* XXX assert csz is non-zero */
+ sc->sc_cachelsz = csz << 2; /* convert to bytes */
+
+ spin_lock_init(&sc->sc_resetlock);
+
+ ah = ath9k_hw_attach(devid, sc, sc->mem, &status);
+ if (ah == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to attach hardware; HAL status %u\n",
+ __func__, status);
+ error = -ENXIO;
+ goto bad;
+ }
+ sc->sc_ah = ah;
+
+ /* Get the chipset-specific aggr limit. */
+ sc->sc_rtsaggrlimit = ah->ah_caps.rts_aggr_limit;
+
+ /* Get the hardware key cache size. */
+ sc->sc_keymax = ah->ah_caps.keycache_size;
+ if (sc->sc_keymax > ATH_KEYMAX) {
+ DPRINTF(sc, ATH_DBG_KEYCACHE,
+ "%s: Warning, using only %u entries in %u key cache\n",
+ __func__, ATH_KEYMAX, sc->sc_keymax);
+ sc->sc_keymax = ATH_KEYMAX;
+ }
+
+ /*
+ * Reset the key cache since some parts do not
+ * reset the contents on initial power up.
+ */
+ for (i = 0; i < sc->sc_keymax; i++)
+ ath9k_hw_keyreset(ah, (u16) i);
+ /*
+ * Mark key cache slots associated with global keys
+ * as in use. If we knew TKIP was not to be used we
+ * could leave the +32, +64, and +32+64 slots free.
+ * XXX only for splitmic.
+ */
+ for (i = 0; i < IEEE80211_WEP_NKID; i++) {
+ set_bit(i, sc->sc_keymap);
+ set_bit(i + 32, sc->sc_keymap);
+ set_bit(i + 64, sc->sc_keymap);
+ set_bit(i + 32 + 64, sc->sc_keymap);
+ }
+ /*
+ * Collect the channel list using the default country
+ * code and including outdoor channels. The 802.11 layer
+ * is resposible for filtering this list based on settings
+ * like the phy mode.
+ */
+ rd = ah->ah_currentRD;
+
+ error = ath_setup_channels(sc);
+ if (error)
+ goto bad;
+
+ /* default to STA mode */
+ sc->sc_opmode = ATH9K_M_MONITOR;
+
+ /* Setup rate tables */
+
+ ath_setup_rates(sc, IEEE80211_BAND_2GHZ);
+ ath_setup_rates(sc, IEEE80211_BAND_5GHZ);
+
+ /* NB: setup here so ath_rate_update is happy */
+ ath_setcurmode(sc, ATH9K_MODE_11A);
+
+ /*
+ * Allocate hardware transmit queues: one queue for
+ * beacon frames and one data queue for each QoS
+ * priority. Note that the hal handles reseting
+ * these queues at the needed time.
+ */
+ sc->sc_bhalq = ath_beaconq_setup(ah);
+ if (sc->sc_bhalq == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup a beacon xmit queue\n", __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ sc->sc_cabq = ath_txq_setup(sc, ATH9K_TX_QUEUE_CAB, 0);
+ if (sc->sc_cabq == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup CAB xmit queue\n", __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ sc->sc_config.cabqReadytime = ATH_CABQ_READY_TIME;
+ ath_cabq_update(sc);
+
+ for (i = 0; i < ARRAY_SIZE(sc->sc_haltype2q); i++)
+ sc->sc_haltype2q[i] = -1;
+
+ /* Setup data queues */
+ /* NB: ensure BK queue is the lowest priority h/w queue */
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_BK)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for BK traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_BE)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for BE traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_VI)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for VI traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_VO)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for VO traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ sc->sc_rc = ath_rate_attach(ah);
+ if (sc->sc_rc == NULL) {
+ error = EIO;
+ goto bad2;
+ }
+
+ if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_TKIP, NULL)) {
+ /*
+ * Whether we should enable h/w TKIP MIC.
+ * XXX: if we don't support WME TKIP MIC, then we wouldn't
+ * report WMM capable, so it's always safe to turn on
+ * TKIP MIC in this case.
+ */
+ ath9k_hw_setcapability(sc->sc_ah, ATH9K_CAP_TKIP_MIC,
+ 0, 1, NULL);
+ }
+
+ /*
+ * Check whether the separate key cache entries
+ * are required to handle both tx+rx MIC keys.
+ * With split mic keys the number of stations is limited
+ * to 27 otherwise 59.
+ */
+ if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_TKIP, NULL)
+ && ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_MIC, NULL)
+ && ath9k_hw_getcapability(ah, ATH9K_CAP_TKIP_SPLIT,
+ 0, NULL))
+ sc->sc_splitmic = 1;
+
+ /* turn on mcast key search if possible */
+ if (!ath9k_hw_getcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 0, NULL))
+ (void)ath9k_hw_setcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 1,
+ 1, NULL);
+
+ sc->sc_config.txpowlimit = ATH_TXPOWER_MAX;
+ sc->sc_config.txpowlimit_override = 0;
+
+ /* 11n Capabilities */
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) {
+ sc->sc_txaggr = 1;
+ sc->sc_rxaggr = 1;
+ }
+
+ sc->sc_tx_chainmask = ah->ah_caps.tx_chainmask;
+ sc->sc_rx_chainmask = ah->ah_caps.rx_chainmask;
+
+ /* Configuration for rx chain detection */
+ sc->sc_rxchaindetect_ref = 0;
+ sc->sc_rxchaindetect_thresh5GHz = 35;
+ sc->sc_rxchaindetect_thresh2GHz = 35;
+ sc->sc_rxchaindetect_delta5GHz = 30;
+ sc->sc_rxchaindetect_delta2GHz = 30;
+
+ ath9k_hw_setcapability(ah, ATH9K_CAP_DIVERSITY, 1, true, NULL);
+ sc->sc_defant = ath9k_hw_getdefantenna(ah);
+
+ ath9k_hw_getmac(ah, sc->sc_myaddr);
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_BSSIDMASK) {
+ ath9k_hw_getbssidmask(ah, sc->sc_bssidmask);
+ ATH_SET_VAP_BSSID_MASK(sc->sc_bssidmask);
+ ath9k_hw_setbssidmask(ah, sc->sc_bssidmask);
+ }
+ sc->sc_slottime = ATH9K_SLOT_TIME_9; /* default to short slot time */
+
+ /* initialize beacon slots */
+ for (i = 0; i < ARRAY_SIZE(sc->sc_bslot); i++)
+ sc->sc_bslot[i] = ATH_IF_ID_ANY;
+
+ /* save MISC configurations */
+ sc->sc_config.swBeaconProcess = 1;
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ /* range is 40 - 255, we use something in the middle */
+ ath_slow_ant_div_init(&sc->sc_antdiv, sc, 0x127);
+#endif
+
+ return 0;
+bad2:
+ /* cleanup tx queues */
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++)
+ if (ATH_TXQ_SETUP(sc, i))
+ ath_tx_cleanupq(sc, &sc->sc_txq[i]);
+bad:
+ if (ah)
+ ath9k_hw_detach(ah);
+ return error;
+}
+
+void ath_deinit(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int i;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s\n", __func__);
+
+ ath_stop(sc);
+ if (!sc->sc_invalid)
+ ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_AWAKE);
+ ath_rate_detach(sc->sc_rc);
+ /* cleanup tx queues */
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++)
+ if (ATH_TXQ_SETUP(sc, i))
+ ath_tx_cleanupq(sc, &sc->sc_txq[i]);
+ ath9k_hw_detach(ah);
+}
+
+/*******************/
+/* Node Management */
+/*******************/
+
+struct ath_node *ath_node_attach(struct ath_softc *sc, u8 *addr, int if_id)
+{
+ struct ath_vap *avp;
+ struct ath_node *an;
+ DECLARE_MAC_BUF(mac);
+
+ avp = sc->sc_vaps[if_id];
+ ASSERT(avp != NULL);
+
+ /* mac80211 sta_notify callback is from an IRQ context, so no sleep */
+ an = kmalloc(sizeof(struct ath_node), GFP_ATOMIC);
+ if (an == NULL)
+ return NULL;
+ memzero(an, sizeof(*an));
+
+ an->an_sc = sc;
+ memcpy(an->an_addr, addr, ETH_ALEN);
+ atomic_set(&an->an_refcnt, 1);
+
+ /* set up per-node tx/rx state */
+ ath_tx_node_init(sc, an);
+ ath_rx_node_init(sc, an);
+
+ ath_chainmask_sel_init(sc, an);
+ ath_chainmask_sel_timerstart(&an->an_chainmask_sel);
+ list_add(&an->list, &sc->node_list);
+
+ return an;
+}
+
+void ath_node_detach(struct ath_softc *sc, struct ath_node *an, bool bh_flag)
+{
+ unsigned long flags;
+
+ DECLARE_MAC_BUF(mac);
+
+ ath_chainmask_sel_timerstop(&an->an_chainmask_sel);
+ an->an_flags |= ATH_NODE_CLEAN;
+ ath_tx_node_cleanup(sc, an, bh_flag);
+ ath_rx_node_cleanup(sc, an);
+
+ ath_tx_node_free(sc, an);
+ ath_rx_node_free(sc, an);
+
+ spin_lock_irqsave(&sc->node_lock, flags);
+
+ list_del(&an->list);
+
+ spin_unlock_irqrestore(&sc->node_lock, flags);
+
+ kfree(an);
+}
+
+/* Finds a node and increases the refcnt if found */
+
+struct ath_node *ath_node_get(struct ath_softc *sc, u8 *addr)
+{
+ struct ath_node *an = NULL, *an_found = NULL;
+
+ if (list_empty(&sc->node_list)) /* FIXME */
+ goto out;
+ list_for_each_entry(an, &sc->node_list, list) {
+ if (!compare_ether_addr(an->an_addr, addr)) {
+ atomic_inc(&an->an_refcnt);
+ an_found = an;
+ break;
+ }
+ }
+out:
+ return an_found;
+}
+
+/* Decrements the refcnt and if it drops to zero, detach the node */
+
+void ath_node_put(struct ath_softc *sc, struct ath_node *an, bool bh_flag)
+{
+ if (atomic_dec_and_test(&an->an_refcnt))
+ ath_node_detach(sc, an, bh_flag);
+}
+
+/* Finds a node, doesn't increment refcnt. Caller must hold sc->node_lock */
+struct ath_node *ath_node_find(struct ath_softc *sc, u8 *addr)
+{
+ struct ath_node *an = NULL, *an_found = NULL;
+
+ if (list_empty(&sc->node_list))
+ return NULL;
+
+ list_for_each_entry(an, &sc->node_list, list)
+ if (!compare_ether_addr(an->an_addr, addr)) {
+ an_found = an;
+ break;
+ }
+
+ return an_found;
+}
+
+/*
+ * Set up New Node
+ *
+ * Setup driver-specific state for a newly associated node. This routine
+ * really only applies if compression or XR are enabled, there is no code
+ * covering any other cases.
+*/
+
+void ath_newassoc(struct ath_softc *sc,
+ struct ath_node *an, int isnew, int isuapsd)
+{
+ int tidno;
+
+ /* if station reassociates, tear down the aggregation state. */
+ if (!isnew) {
+ for (tidno = 0; tidno < WME_NUM_TID; tidno++) {
+ if (sc->sc_txaggr)
+ ath_tx_aggr_teardown(sc, an, tidno);
+ if (sc->sc_rxaggr)
+ ath_rx_aggr_teardown(sc, an, tidno);
+ }
+ }
+ an->an_flags = 0;
+}
+
+/**************/
+/* Encryption */
+/**************/
+
+void ath_key_reset(struct ath_softc *sc, u16 keyix, int freeslot)
+{
+ ath9k_hw_keyreset(sc->sc_ah, keyix);
+ if (freeslot)
+ clear_bit(keyix, sc->sc_keymap);
+}
+
+int ath_keyset(struct ath_softc *sc,
+ u16 keyix,
+ struct ath9k_keyval *hk,
+ const u8 mac[ETH_ALEN])
+{
+ bool status;
+
+ status = ath9k_hw_set_keycache_entry(sc->sc_ah,
+ keyix, hk, mac, false);
+
+ return status != false;
+}
+
+/***********************/
+/* TX Power/Regulatory */
+/***********************/
+
+/*
+ * Set Transmit power in HAL
+ *
+ * This routine makes the actual HAL calls to set the new transmit power
+ * limit.
+*/
+
+void ath_update_txpow(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u32 txpow;
+
+ if (sc->sc_curtxpow != sc->sc_config.txpowlimit) {
+ ath9k_hw_set_txpowerlimit(ah, sc->sc_config.txpowlimit);
+ /* read back in case value is clamped */
+ ath9k_hw_getcapability(ah, ATH9K_CAP_TXPOW, 1, &txpow);
+ sc->sc_curtxpow = txpow;
+ }
+}
+
+/* Return the current country and domain information */
+void ath_get_currentCountry(struct ath_softc *sc,
+ struct ath9k_country_entry *ctry)
+{
+ ath9k_regd_get_current_country(sc->sc_ah, ctry);
+
+ /* If HAL not specific yet, since it is band dependent,
+ * use the one we passed in. */
+ if (ctry->countryCode == CTRY_DEFAULT) {
+ ctry->iso[0] = 0;
+ ctry->iso[1] = 0;
+ } else if (ctry->iso[0] && ctry->iso[1]) {
+ if (!ctry->iso[2]) {
+ if (ath_outdoor)
+ ctry->iso[2] = 'O';
+ else
+ ctry->iso[2] = 'I';
+ }
+ }
+}
+
+/**************************/
+/* Slow Antenna Diversity */
+/**************************/
+
+void ath_slow_ant_div_init(struct ath_antdiv *antdiv,
+ struct ath_softc *sc,
+ int32_t rssitrig)
+{
+ int trig;
+
+ /* antdivf_rssitrig can range from 40 - 0xff */
+ trig = (rssitrig > 0xff) ? 0xff : rssitrig;
+ trig = (rssitrig < 40) ? 40 : rssitrig;
+
+ antdiv->antdiv_sc = sc;
+ antdiv->antdivf_rssitrig = trig;
+}
+
+void ath_slow_ant_div_start(struct ath_antdiv *antdiv,
+ u8 num_antcfg,
+ const u8 *bssid)
+{
+ antdiv->antdiv_num_antcfg =
+ num_antcfg < ATH_ANT_DIV_MAX_CFG ?
+ num_antcfg : ATH_ANT_DIV_MAX_CFG;
+ antdiv->antdiv_state = ATH_ANT_DIV_IDLE;
+ antdiv->antdiv_curcfg = 0;
+ antdiv->antdiv_bestcfg = 0;
+ antdiv->antdiv_laststatetsf = 0;
+
+ memcpy(antdiv->antdiv_bssid, bssid, sizeof(antdiv->antdiv_bssid));
+
+ antdiv->antdiv_start = 1;
+}
+
+void ath_slow_ant_div_stop(struct ath_antdiv *antdiv)
+{
+ antdiv->antdiv_start = 0;
+}
+
+static int32_t ath_find_max_val(int32_t *val,
+ u8 num_val, u8 *max_index)
+{
+ u32 MaxVal = *val++;
+ u32 cur_index = 0;
+
+ *max_index = 0;
+ while (++cur_index < num_val) {
+ if (*val > MaxVal) {
+ MaxVal = *val;
+ *max_index = cur_index;
+ }
+
+ val++;
+ }
+
+ return MaxVal;
+}
+
+void ath_slow_ant_div(struct ath_antdiv *antdiv,
+ struct ieee80211_hdr *hdr,
+ struct ath_rx_status *rx_stats)
+{
+ struct ath_softc *sc = antdiv->antdiv_sc;
+ struct ath_hal *ah = sc->sc_ah;
+ u64 curtsf = 0;
+ u8 bestcfg, curcfg = antdiv->antdiv_curcfg;
+ __le16 fc = hdr->frame_control;
+
+ if (antdiv->antdiv_start && ieee80211_is_beacon(fc)
+ && !compare_ether_addr(hdr->addr3, antdiv->antdiv_bssid)) {
+ antdiv->antdiv_lastbrssi[curcfg] = rx_stats->rs_rssi;
+ antdiv->antdiv_lastbtsf[curcfg] = ath9k_hw_gettsf64(sc->sc_ah);
+ curtsf = antdiv->antdiv_lastbtsf[curcfg];
+ } else {
+ return;
+ }
+
+ switch (antdiv->antdiv_state) {
+ case ATH_ANT_DIV_IDLE:
+ if ((antdiv->antdiv_lastbrssi[curcfg] <
+ antdiv->antdivf_rssitrig)
+ && ((curtsf - antdiv->antdiv_laststatetsf) >
+ ATH_ANT_DIV_MIN_IDLE_US)) {
+
+ curcfg++;
+ if (curcfg == antdiv->antdiv_num_antcfg)
+ curcfg = 0;
+
+ if (!ath9k_hw_select_antconfig(ah, curcfg)) {
+ antdiv->antdiv_bestcfg = antdiv->antdiv_curcfg;
+ antdiv->antdiv_curcfg = curcfg;
+ antdiv->antdiv_laststatetsf = curtsf;
+ antdiv->antdiv_state = ATH_ANT_DIV_SCAN;
+ }
+ }
+ break;
+
+ case ATH_ANT_DIV_SCAN:
+ if ((curtsf - antdiv->antdiv_laststatetsf) <
+ ATH_ANT_DIV_MIN_SCAN_US)
+ break;
+
+ curcfg++;
+ if (curcfg == antdiv->antdiv_num_antcfg)
+ curcfg = 0;
+
+ if (curcfg == antdiv->antdiv_bestcfg) {
+ ath_find_max_val(antdiv->antdiv_lastbrssi,
+ antdiv->antdiv_num_antcfg, &bestcfg);
+ if (!ath9k_hw_select_antconfig(ah, bestcfg)) {
+ antdiv->antdiv_bestcfg = bestcfg;
+ antdiv->antdiv_curcfg = bestcfg;
+ antdiv->antdiv_laststatetsf = curtsf;
+ antdiv->antdiv_state = ATH_ANT_DIV_IDLE;
+ }
+ } else {
+ if (!ath9k_hw_select_antconfig(ah, curcfg)) {
+ antdiv->antdiv_curcfg = curcfg;
+ antdiv->antdiv_laststatetsf = curtsf;
+ antdiv->antdiv_state = ATH_ANT_DIV_SCAN;
+ }
+ }
+
+ break;
+ }
+}
+
+/***********************/
+/* Descriptor Handling */
+/***********************/
+
+/*
+ * Set up DMA descriptors
+ *
+ * This function will allocate both the DMA descriptor structure, and the
+ * buffers it contains. These are used to contain the descriptors used
+ * by the system.
+*/
+
+int ath_descdma_setup(struct ath_softc *sc,
+ struct ath_descdma *dd,
+ struct list_head *head,
+ const char *name,
+ int nbuf,
+ int ndesc)
+{
+#define DS2PHYS(_dd, _ds) \
+ ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc))
+#define ATH_DESC_4KB_BOUND_CHECK(_daddr) ((((_daddr) & 0xFFF) > 0xF7F) ? 1 : 0)
+#define ATH_DESC_4KB_BOUND_NUM_SKIPPED(_len) ((_len) / 4096)
+
+ struct ath_desc *ds;
+ struct ath_buf *bf;
+ int i, bsize, error;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: %s DMA: %u buffers %u desc/buf\n",
+ __func__, name, nbuf, ndesc);
+
+ /* ath_desc must be a multiple of DWORDs */
+ if ((sizeof(struct ath_desc) % 4) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: ath_desc not DWORD aligned\n",
+ __func__);
+ ASSERT((sizeof(struct ath_desc) % 4) == 0);
+ error = -ENOMEM;
+ goto fail;
+ }
+
+ dd->dd_name = name;
+ dd->dd_desc_len = sizeof(struct ath_desc) * nbuf * ndesc;
+
+ /*
+ * Need additional DMA memory because we can't use
+ * descriptors that cross the 4K page boundary. Assume
+ * one skipped descriptor per 4K page.
+ */
+ if (!(sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_4KB_SPLITTRANS)) {
+ u32 ndesc_skipped =
+ ATH_DESC_4KB_BOUND_NUM_SKIPPED(dd->dd_desc_len);
+ u32 dma_len;
+
+ while (ndesc_skipped) {
+ dma_len = ndesc_skipped * sizeof(struct ath_desc);
+ dd->dd_desc_len += dma_len;
+
+ ndesc_skipped = ATH_DESC_4KB_BOUND_NUM_SKIPPED(dma_len);
+ };
+ }
+
+ /* allocate descriptors */
+ dd->dd_desc = pci_alloc_consistent(sc->pdev,
+ dd->dd_desc_len,
+ &dd->dd_desc_paddr);
+ if (dd->dd_desc == NULL) {
+ error = -ENOMEM;
+ goto fail;
+ }
+ ds = dd->dd_desc;
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: %s DMA map: %p (%u) -> %llx (%u)\n",
+ __func__, dd->dd_name, ds, (u32) dd->dd_desc_len,
+ ito64(dd->dd_desc_paddr), /*XXX*/(u32) dd->dd_desc_len);
+
+ /* allocate buffers */
+ bsize = sizeof(struct ath_buf) * nbuf;
+ bf = kmalloc(bsize, GFP_KERNEL);
+ if (bf == NULL) {
+ error = -ENOMEM;
+ goto fail2;
+ }
+ memzero(bf, bsize);
+ dd->dd_bufptr = bf;
+
+ INIT_LIST_HEAD(head);
+ for (i = 0; i < nbuf; i++, bf++, ds += ndesc) {
+ bf->bf_desc = ds;
+ bf->bf_daddr = DS2PHYS(dd, ds);
+
+ if (!(sc->sc_ah->ah_caps.hw_caps &
+ ATH9K_HW_CAP_4KB_SPLITTRANS)) {
+ /*
+ * Skip descriptor addresses which can cause 4KB
+ * boundary crossing (addr + length) with a 32 dword
+ * descriptor fetch.
+ */
+ while (ATH_DESC_4KB_BOUND_CHECK(bf->bf_daddr)) {
+ ASSERT((caddr_t) bf->bf_desc <
+ ((caddr_t) dd->dd_desc +
+ dd->dd_desc_len));
+
+ ds += ndesc;
+ bf->bf_desc = ds;
+ bf->bf_daddr = DS2PHYS(dd, ds);
+ }
+ }
+ list_add_tail(&bf->list, head);
+ }
+ return 0;
+fail2:
+ pci_free_consistent(sc->pdev,
+ dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+fail:
+ memzero(dd, sizeof(*dd));
+ return error;
+#undef ATH_DESC_4KB_BOUND_CHECK
+#undef ATH_DESC_4KB_BOUND_NUM_SKIPPED
+#undef DS2PHYS
+}
+
+/*
+ * Cleanup DMA descriptors
+ *
+ * This function will free the DMA block that was allocated for the descriptor
+ * pool. Since this was allocated as one "chunk", it is freed in the same
+ * manner.
+*/
+
+void ath_descdma_cleanup(struct ath_softc *sc,
+ struct ath_descdma *dd,
+ struct list_head *head)
+{
+ /* Free memory associated with descriptors */
+ pci_free_consistent(sc->pdev,
+ dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+
+ INIT_LIST_HEAD(head);
+ kfree(dd->dd_bufptr);
+ memzero(dd, sizeof(*dd));
+}
+
+/*************/
+/* Utilities */
+/*************/
+
+void ath_internal_reset(struct ath_softc *sc)
+{
+ ath_reset_start(sc, 0);
+ ath_reset(sc);
+ ath_reset_end(sc, 0);
+}
+
+int ath_get_hal_qnum(u16 queue, struct ath_softc *sc)
+{
+ int qnum;
+
+ switch (queue) {
+ case 0:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_VO];
+ break;
+ case 1:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_VI];
+ break;
+ case 2:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BE];
+ break;
+ case 3:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BK];
+ break;
+ default:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BE];
+ break;
+ }
+
+ return qnum;
+}
+
+int ath_get_mac80211_qnum(u32 queue, struct ath_softc *sc)
+{
+ int qnum;
+
+ switch (queue) {
+ case ATH9K_WME_AC_VO:
+ qnum = 0;
+ break;
+ case ATH9K_WME_AC_VI:
+ qnum = 1;
+ break;
+ case ATH9K_WME_AC_BE:
+ qnum = 2;
+ break;
+ case ATH9K_WME_AC_BK:
+ qnum = 3;
+ break;
+ default:
+ qnum = -1;
+ break;
+ }
+
+ return qnum;
+}
+
+
+/*
+ * Expand time stamp to TSF
+ *
+ * Extend 15-bit time stamp from rx descriptor to
+ * a full 64-bit TSF using the current h/w TSF.
+*/
+
+u64 ath_extend_tsf(struct ath_softc *sc, u32 rstamp)
+{
+ u64 tsf;
+
+ tsf = ath9k_hw_gettsf64(sc->sc_ah);
+ if ((tsf & 0x7fff) < rstamp)
+ tsf -= 0x8000;
+ return (tsf & ~0x7fff) | rstamp;
+}
+
+/*
+ * Set Default Antenna
+ *
+ * Call into the HAL to set the default antenna to use. Not really valid for
+ * MIMO technology.
+*/
+
+void ath_setdefantenna(void *context, u32 antenna)
+{
+ struct ath_softc *sc = (struct ath_softc *)context;
+ struct ath_hal *ah = sc->sc_ah;
+
+ /* XXX block beacon interrupts */
+ ath9k_hw_setantenna(ah, antenna);
+ sc->sc_defant = antenna;
+ sc->sc_rxotherant = 0;
+}
+
+/*
+ * Set Slot Time
+ *
+ * This will wake up the chip if required, and set the slot time for the
+ * frame (maximum transmit time). Slot time is assumed to be already set
+ * in the ATH object member sc_slottime
+*/
+
+void ath_setslottime(struct ath_softc *sc)
+{
+ ath9k_hw_setslottime(sc->sc_ah, sc->sc_slottime);
+ sc->sc_updateslot = OK;
+}
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef CORE_H
+#define CORE_H
+
+#include <linux/version.h>
+#include <linux/autoconf.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/skbuff.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/in.h>
+#include <linux/delay.h>
+#include <linux/wait.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/list.h>
+#include <asm/byteorder.h>
+#include <linux/scatterlist.h>
+#include <asm/page.h>
+#include <net/mac80211.h>
+
+#include "ath9k.h"
+#include "rc.h"
+
+struct ath_node;
+
+/******************/
+/* Utility macros */
+/******************/
+
+/* Macro to expand scalars to 64-bit objects */
+
+#define ito64(x) (sizeof(x) == 8) ? \
+ (((unsigned long long int)(x)) & (0xff)) : \
+ (sizeof(x) == 16) ? \
+ (((unsigned long long int)(x)) & 0xffff) : \
+ ((sizeof(x) == 32) ? \
+ (((unsigned long long int)(x)) & 0xffffffff) : \
+ (unsigned long long int)(x))
+
+/* increment with wrap-around */
+#define INCR(_l, _sz) do { \
+ (_l)++; \
+ (_l) &= ((_sz) - 1); \
+ } while (0)
+
+/* decrement with wrap-around */
+#define DECR(_l, _sz) do { \
+ (_l)--; \
+ (_l) &= ((_sz) - 1); \
+ } while (0)
+
+#define A_MAX(a, b) ((a) > (b) ? (a) : (b))
+
+#define ASSERT(exp) do { \
+ if (unlikely(!(exp))) { \
+ BUG(); \
+ } \
+ } while (0)
+
+/* XXX: remove */
+#define memzero(_buf, _len) memset(_buf, 0, _len)
+
+#define get_dma_mem_context(var, field) (&((var)->field))
+#define copy_dma_mem_context(dst, src) (*dst = *src)
+
+#define ATH9K_BH_STATUS_INTACT 0
+#define ATH9K_BH_STATUS_CHANGE 1
+
+#define ATH_TXQ_SETUP(sc, i) ((sc)->sc_txqsetup & (1<<i))
+
+static inline unsigned long get_timestamp(void)
+{
+ return ((jiffies / HZ) * 1000) + (jiffies % HZ) * (1000 / HZ);
+}
+
+/*************/
+/* Debugging */
+/*************/
+
+enum ATH_DEBUG {
+ ATH_DBG_RESET = 0x00000001,
+ ATH_DBG_PHY_IO = 0x00000002,
+ ATH_DBG_REG_IO = 0x00000004,
+ ATH_DBG_QUEUE = 0x00000008,
+ ATH_DBG_EEPROM = 0x00000010,
+ ATH_DBG_NF_CAL = 0x00000020,
+ ATH_DBG_CALIBRATE = 0x00000040,
+ ATH_DBG_CHANNEL = 0x00000080,
+ ATH_DBG_INTERRUPT = 0x00000100,
+ ATH_DBG_REGULATORY = 0x00000200,
+ ATH_DBG_ANI = 0x00000400,
+ ATH_DBG_POWER_MGMT = 0x00000800,
+ ATH_DBG_XMIT = 0x00001000,
+ ATH_DBG_BEACON = 0x00002000,
+ ATH_DBG_RATE = 0x00004000,
+ ATH_DBG_CONFIG = 0x00008000,
+ ATH_DBG_KEYCACHE = 0x00010000,
+ ATH_DBG_AGGR = 0x00020000,
+ ATH_DBG_FATAL = 0x00040000,
+ ATH_DBG_ANY = 0xffffffff
+};
+
+#define DBG_DEFAULT (ATH_DBG_FATAL)
+
+#define DPRINTF(sc, _m, _fmt, ...) do { \
+ if (sc->sc_debug & (_m)) \
+ printk(_fmt , ##__VA_ARGS__); \
+ } while (0)
+
+/***************************/
+/* Load-time Configuration */
+/***************************/
+
+/* Per-instance load-time (note: NOT run-time) configurations
+ * for Atheros Device */
+struct ath_config {
+ u32 ath_aggr_prot;
+ u16 txpowlimit;
+ u16 txpowlimit_override;
+ u8 cabqReadytime; /* Cabq Readytime % */
+ u8 swBeaconProcess; /* Process received beacons in SW (vs HW) */
+};
+
+/***********************/
+/* Chainmask Selection */
+/***********************/
+
+#define ATH_CHAINMASK_SEL_TIMEOUT 6000
+/* Default - Number of last RSSI values that is used for
+ * chainmask selection */
+#define ATH_CHAINMASK_SEL_RSSI_CNT 10
+/* Means use 3x3 chainmask instead of configured chainmask */
+#define ATH_CHAINMASK_SEL_3X3 7
+/* Default - Rssi threshold below which we have to switch to 3x3 */
+#define ATH_CHAINMASK_SEL_UP_RSSI_THRES 20
+/* Default - Rssi threshold above which we have to switch to
+ * user configured values */
+#define ATH_CHAINMASK_SEL_DOWN_RSSI_THRES 35
+/* Struct to store the chainmask select related info */
+struct ath_chainmask_sel {
+ struct timer_list timer;
+ int cur_tx_mask; /* user configured or 3x3 */
+ int cur_rx_mask; /* user configured or 3x3 */
+ int tx_avgrssi;
+ u8 switch_allowed:1, /* timer will set this */
+ cm_sel_enabled : 1;
+};
+
+int ath_chainmask_sel_logic(struct ath_softc *sc, struct ath_node *an);
+void ath_update_chainmask(struct ath_softc *sc, int is_ht);
+
+/*************************/
+/* Descriptor Management */
+/*************************/
+
+/* Number of descriptors per buffer. The only case where we see skbuff
+chains is due to FF aggregation in the driver. */
+#define ATH_TXDESC 1
+/* if there's more fragment for this MSDU */
+#define ATH_BF_MORE_MPDU 1
+#define ATH_TXBUF_RESET(_bf) do { \
+ (_bf)->bf_status = 0; \
+ (_bf)->bf_lastbf = NULL; \
+ (_bf)->bf_lastfrm = NULL; \
+ (_bf)->bf_next = NULL; \
+ memzero(&((_bf)->bf_state), \
+ sizeof(struct ath_buf_state)); \
+ } while (0)
+
+struct ath_buf_state {
+ int bfs_nframes; /* # frames in aggregate */
+ u16 bfs_al; /* length of aggregate */
+ u16 bfs_frmlen; /* length of frame */
+ int bfs_seqno; /* sequence number */
+ int bfs_tidno; /* tid of this frame */
+ int bfs_retries; /* current retries */
+ struct ath_rc_series bfs_rcs[4]; /* rate series */
+ u8 bfs_isdata:1; /* is a data frame/aggregate */
+ u8 bfs_isaggr:1; /* is an aggregate */
+ u8 bfs_isampdu:1; /* is an a-mpdu, aggregate or not */
+ u8 bfs_ht:1; /* is an HT frame */
+ u8 bfs_isretried:1; /* is retried */
+ u8 bfs_isxretried:1; /* is excessive retried */
+ u8 bfs_shpreamble:1; /* is short preamble */
+ u8 bfs_isbar:1; /* is a BAR */
+ u8 bfs_ispspoll:1; /* is a PS-Poll */
+ u8 bfs_aggrburst:1; /* is a aggr burst */
+ u8 bfs_calcairtime:1; /* requests airtime be calculated
+ when set for tx frame */
+ int bfs_rifsburst_elem; /* RIFS burst/bar */
+ int bfs_nrifsubframes; /* # of elements in burst */
+ /* key type use to encrypt this frame */
+ enum ath9k_key_type bfs_keytype;
+};
+
+#define bf_nframes bf_state.bfs_nframes
+#define bf_al bf_state.bfs_al
+#define bf_frmlen bf_state.bfs_frmlen
+#define bf_retries bf_state.bfs_retries
+#define bf_seqno bf_state.bfs_seqno
+#define bf_tidno bf_state.bfs_tidno
+#define bf_rcs bf_state.bfs_rcs
+#define bf_isdata bf_state.bfs_isdata
+#define bf_isaggr bf_state.bfs_isaggr
+#define bf_isampdu bf_state.bfs_isampdu
+#define bf_ht bf_state.bfs_ht
+#define bf_isretried bf_state.bfs_isretried
+#define bf_isxretried bf_state.bfs_isxretried
+#define bf_shpreamble bf_state.bfs_shpreamble
+#define bf_rifsburst_elem bf_state.bfs_rifsburst_elem
+#define bf_nrifsubframes bf_state.bfs_nrifsubframes
+#define bf_keytype bf_state.bfs_keytype
+#define bf_isbar bf_state.bfs_isbar
+#define bf_ispspoll bf_state.bfs_ispspoll
+#define bf_aggrburst bf_state.bfs_aggrburst
+#define bf_calcairtime bf_state.bfs_calcairtime
+
+/*
+ * Abstraction of a contiguous buffer to transmit/receive. There is only
+ * a single hw descriptor encapsulated here.
+ */
+
+struct ath_buf {
+ struct list_head list;
+ struct list_head *last;
+ struct ath_buf *bf_lastbf; /* last buf of this unit (a frame or
+ an aggregate) */
+ struct ath_buf *bf_lastfrm; /* last buf of this frame */
+ struct ath_buf *bf_next; /* next subframe in the aggregate */
+ struct ath_buf *bf_rifslast; /* last buf for RIFS burst */
+ void *bf_mpdu; /* enclosing frame structure */
+ void *bf_node; /* pointer to the node */
+ struct ath_desc *bf_desc; /* virtual addr of desc */
+ dma_addr_t bf_daddr; /* physical addr of desc */
+ dma_addr_t bf_buf_addr; /* physical addr of data buffer */
+ u32 bf_status;
+ u16 bf_flags; /* tx descriptor flags */
+ struct ath_buf_state bf_state; /* buffer state */
+ dma_addr_t bf_dmacontext;
+};
+
+/*
+ * reset the rx buffer.
+ * any new fields added to the athbuf and require
+ * reset need to be added to this macro.
+ * currently bf_status is the only one requires that
+ * requires reset.
+ */
+#define ATH_RXBUF_RESET(_bf) ((_bf)->bf_status = 0)
+
+/* hw processing complete, desc processed by hal */
+#define ATH_BUFSTATUS_DONE 0x00000001
+/* hw processing complete, desc hold for hw */
+#define ATH_BUFSTATUS_STALE 0x00000002
+/* Rx-only: OS is done with this packet and it's ok to queued it to hw */
+#define ATH_BUFSTATUS_FREE 0x00000004
+
+/* DMA state for tx/rx descriptors */
+
+struct ath_descdma {
+ const char *dd_name;
+ struct ath_desc *dd_desc; /* descriptors */
+ dma_addr_t dd_desc_paddr; /* physical addr of dd_desc */
+ u32 dd_desc_len; /* size of dd_desc */
+ struct ath_buf *dd_bufptr; /* associated buffers */
+ dma_addr_t dd_dmacontext;
+};
+
+/* Abstraction of a received RX MPDU/MMPDU, or a RX fragment */
+
+struct ath_rx_context {
+ struct ath_buf *ctx_rxbuf; /* associated ath_buf for rx */
+};
+#define ATH_RX_CONTEXT(skb) ((struct ath_rx_context *)skb->cb)
+
+int ath_descdma_setup(struct ath_softc *sc,
+ struct ath_descdma *dd,
+ struct list_head *head,
+ const char *name,
+ int nbuf,
+ int ndesc);
+int ath_desc_alloc(struct ath_softc *sc);
+void ath_desc_free(struct ath_softc *sc);
+void ath_descdma_cleanup(struct ath_softc *sc,
+ struct ath_descdma *dd,
+ struct list_head *head);
+
+/******/
+/* RX */
+/******/
+
+#define ATH_MAX_ANTENNA 3
+#define ATH_RXBUF 512
+#define ATH_RX_TIMEOUT 40 /* 40 milliseconds */
+#define WME_NUM_TID 16
+#define IEEE80211_BAR_CTL_TID_M 0xF000 /* tid mask */
+#define IEEE80211_BAR_CTL_TID_S 2 /* tid shift */
+
+enum ATH_RX_TYPE {
+ ATH_RX_NON_CONSUMED = 0,
+ ATH_RX_CONSUMED
+};
+
+/* per frame rx status block */
+struct ath_recv_status {
+ u64 tsf; /* mac tsf */
+ int8_t rssi; /* RSSI (noise floor ajusted) */
+ int8_t rssictl[ATH_MAX_ANTENNA]; /* RSSI (noise floor ajusted) */
+ int8_t rssiextn[ATH_MAX_ANTENNA]; /* RSSI (noise floor ajusted) */
+ int8_t abs_rssi; /* absolute RSSI */
+ u8 rateieee; /* data rate received (IEEE rate code) */
+ u8 ratecode; /* phy rate code */
+ int rateKbps; /* data rate received (Kbps) */
+ int antenna; /* rx antenna */
+ int flags; /* status of associated skb */
+#define ATH_RX_FCS_ERROR 0x01
+#define ATH_RX_MIC_ERROR 0x02
+#define ATH_RX_DECRYPT_ERROR 0x04
+#define ATH_RX_RSSI_VALID 0x08
+/* if any of ctl,extn chainrssis are valid */
+#define ATH_RX_CHAIN_RSSI_VALID 0x10
+/* if extn chain rssis are valid */
+#define ATH_RX_RSSI_EXTN_VALID 0x20
+/* set if 40Mhz, clear if 20Mhz */
+#define ATH_RX_40MHZ 0x40
+/* set if short GI, clear if full GI */
+#define ATH_RX_SHORT_GI 0x80
+};
+
+struct ath_rxbuf {
+ struct sk_buff *rx_wbuf;
+ unsigned long rx_time; /* system time when received */
+ struct ath_recv_status rx_status; /* cached rx status */
+};
+
+/* Per-TID aggregate receiver state for a node */
+struct ath_arx_tid {
+ struct ath_node *an;
+ struct ath_rxbuf *rxbuf; /* re-ordering buffer */
+ struct timer_list timer;
+ spinlock_t tidlock;
+ int baw_head; /* seq_next at head */
+ int baw_tail; /* tail of block-ack window */
+ int seq_reset; /* need to reset start sequence */
+ int addba_exchangecomplete;
+ u16 seq_next; /* next expected sequence */
+ u16 baw_size; /* block-ack window size */
+};
+
+/* Per-node receiver aggregate state */
+struct ath_arx {
+ struct ath_arx_tid tid[WME_NUM_TID];
+};
+
+int ath_startrecv(struct ath_softc *sc);
+bool ath_stoprecv(struct ath_softc *sc);
+void ath_flushrecv(struct ath_softc *sc);
+u32 ath_calcrxfilter(struct ath_softc *sc);
+void ath_rx_node_init(struct ath_softc *sc, struct ath_node *an);
+void ath_rx_node_free(struct ath_softc *sc, struct ath_node *an);
+void ath_rx_node_cleanup(struct ath_softc *sc, struct ath_node *an);
+void ath_handle_rx_intr(struct ath_softc *sc);
+int ath_rx_init(struct ath_softc *sc, int nbufs);
+void ath_rx_cleanup(struct ath_softc *sc);
+int ath_rx_tasklet(struct ath_softc *sc, int flush);
+int ath_rx_input(struct ath_softc *sc,
+ struct ath_node *node,
+ int is_ampdu,
+ struct sk_buff *skb,
+ struct ath_recv_status *rx_status,
+ enum ATH_RX_TYPE *status);
+int ath__rx_indicate(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_recv_status *status,
+ u16 keyix);
+int ath_rx_subframe(struct ath_node *an, struct sk_buff *skb,
+ struct ath_recv_status *status);
+
+/******/
+/* TX */
+/******/
+
+#define ATH_FRAG_PER_MSDU 1
+#define ATH_TXBUF (512/ATH_FRAG_PER_MSDU)
+/* max number of transmit attempts (tries) */
+#define ATH_TXMAXTRY 13
+/* max number of 11n transmit attempts (tries) */
+#define ATH_11N_TXMAXTRY 10
+/* max number of tries for management and control frames */
+#define ATH_MGT_TXMAXTRY 4
+#define WME_BA_BMP_SIZE 64
+#define WME_MAX_BA WME_BA_BMP_SIZE
+#define ATH_TID_MAX_BUFS (2 * WME_MAX_BA)
+#define TID_TO_WME_AC(_tid) \
+ ((((_tid) == 0) || ((_tid) == 3)) ? WME_AC_BE : \
+ (((_tid) == 1) || ((_tid) == 2)) ? WME_AC_BK : \
+ (((_tid) == 4) || ((_tid) == 5)) ? WME_AC_VI : \
+ WME_AC_VO)
+
+
+/* Wireless Multimedia Extension Defines */
+#define WME_AC_BE 0 /* best effort */
+#define WME_AC_BK 1 /* background */
+#define WME_AC_VI 2 /* video */
+#define WME_AC_VO 3 /* voice */
+#define WME_NUM_AC 4
+
+enum ATH_SM_PWRSAV{
+ ATH_SM_ENABLE,
+ ATH_SM_PWRSAV_STATIC,
+ ATH_SM_PWRSAV_DYNAMIC,
+};
+
+/*
+ * Data transmit queue state. One of these exists for each
+ * hardware transmit queue. Packets sent to us from above
+ * are assigned to queues based on their priority. Not all
+ * devices support a complete set of hardware transmit queues.
+ * For those devices the array sc_ac2q will map multiple
+ * priorities to fewer hardware queues (typically all to one
+ * hardware queue).
+ */
+struct ath_txq {
+ u32 axq_qnum; /* hardware q number */
+ u32 *axq_link; /* link ptr in last TX desc */
+ struct list_head axq_q; /* transmit queue */
+ spinlock_t axq_lock;
+ unsigned long axq_lockflags; /* intr state when must cli */
+ u32 axq_depth; /* queue depth */
+ u8 axq_aggr_depth; /* aggregates queued */
+ u32 axq_totalqueued; /* total ever queued */
+
+ /* count to determine if descriptor should generate int on this txq. */
+ u32 axq_intrcnt;
+
+ bool stopped; /* Is mac80211 queue stopped ? */
+ struct ath_buf *axq_linkbuf; /* virtual addr of last buffer*/
+
+ /* first desc of the last descriptor that contains CTS */
+ struct ath_desc *axq_lastdsWithCTS;
+
+ /* final desc of the gating desc that determines whether
+ lastdsWithCTS has been DMA'ed or not */
+ struct ath_desc *axq_gatingds;
+
+ struct list_head axq_acq;
+};
+
+/* per TID aggregate tx state for a destination */
+struct ath_atx_tid {
+ struct list_head list; /* round-robin tid entry */
+ struct list_head buf_q; /* pending buffers */
+ struct ath_node *an;
+ struct ath_atx_ac *ac;
+ struct ath_buf *tx_buf[ATH_TID_MAX_BUFS]; /* active tx frames */
+ u16 seq_start;
+ u16 seq_next;
+ u16 baw_size;
+ int tidno;
+ int baw_head; /* first un-acked tx buffer */
+ int baw_tail; /* next unused tx buffer slot */
+ int sched;
+ int paused;
+ int cleanup_inprogress;
+ u32 addba_exchangecomplete:1;
+ int32_t addba_exchangeinprogress;
+ int addba_exchangeattempts;
+};
+
+/* per access-category aggregate tx state for a destination */
+struct ath_atx_ac {
+ int sched; /* dest-ac is scheduled */
+ int qnum; /* H/W queue number associated
+ with this AC */
+ struct list_head list; /* round-robin txq entry */
+ struct list_head tid_q; /* queue of TIDs with buffers */
+};
+
+/* per dest tx state */
+struct ath_atx {
+ struct ath_atx_tid tid[WME_NUM_TID];
+ struct ath_atx_ac ac[WME_NUM_AC];
+};
+
+/* per-frame tx control block */
+struct ath_tx_control {
+ struct ath_node *an;
+ int if_id;
+ int qnum;
+ u32 ht:1;
+ u32 ps:1;
+ u32 use_minrate:1;
+ enum ath9k_pkt_type atype;
+ enum ath9k_key_type keytype;
+ u32 flags;
+ u16 seqno;
+ u16 tidno;
+ u16 txpower;
+ u16 frmlen;
+ u32 keyix;
+ int min_rate;
+ int mcast_rate;
+ u16 nextfraglen;
+ struct ath_softc *dev;
+ dma_addr_t dmacontext;
+};
+
+/* per frame tx status block */
+struct ath_xmit_status {
+ int retries; /* number of retries to successufully
+ transmit this frame */
+ int flags; /* status of transmit */
+#define ATH_TX_ERROR 0x01
+#define ATH_TX_XRETRY 0x02
+#define ATH_TX_BAR 0x04
+};
+
+struct ath_tx_stat {
+ int rssi; /* RSSI (noise floor ajusted) */
+ int rssictl[ATH_MAX_ANTENNA]; /* RSSI (noise floor ajusted) */
+ int rssiextn[ATH_MAX_ANTENNA]; /* RSSI (noise floor ajusted) */
+ int rateieee; /* data rate xmitted (IEEE rate code) */
+ int rateKbps; /* data rate xmitted (Kbps) */
+ int ratecode; /* phy rate code */
+ int flags; /* validity flags */
+/* if any of ctl,extn chain rssis are valid */
+#define ATH_TX_CHAIN_RSSI_VALID 0x01
+/* if extn chain rssis are valid */
+#define ATH_TX_RSSI_EXTN_VALID 0x02
+ u32 airtime; /* time on air per final tx rate */
+};
+
+struct ath_txq *ath_txq_setup(struct ath_softc *sc, int qtype, int subtype);
+void ath_tx_cleanupq(struct ath_softc *sc, struct ath_txq *txq);
+int ath_tx_setup(struct ath_softc *sc, int haltype);
+void ath_draintxq(struct ath_softc *sc, bool retry_tx);
+void ath_tx_draintxq(struct ath_softc *sc,
+ struct ath_txq *txq, bool retry_tx);
+void ath_tx_node_init(struct ath_softc *sc, struct ath_node *an);
+void ath_tx_node_cleanup(struct ath_softc *sc,
+ struct ath_node *an, bool bh_flag);
+void ath_tx_node_free(struct ath_softc *sc, struct ath_node *an);
+void ath_txq_schedule(struct ath_softc *sc, struct ath_txq *txq);
+int ath_tx_init(struct ath_softc *sc, int nbufs);
+int ath_tx_cleanup(struct ath_softc *sc);
+int ath_tx_get_qnum(struct ath_softc *sc, int qtype, int haltype);
+int ath_txq_update(struct ath_softc *sc, int qnum,
+ struct ath9k_tx_queue_info *q);
+int ath_tx_start(struct ath_softc *sc, struct sk_buff *skb);
+void ath_tx_tasklet(struct ath_softc *sc);
+u32 ath_txq_depth(struct ath_softc *sc, int qnum);
+u32 ath_txq_aggr_depth(struct ath_softc *sc, int qnum);
+void ath_notify_txq_status(struct ath_softc *sc, u16 queue_depth);
+void ath_tx_complete(struct ath_softc *sc, struct sk_buff *skb,
+ struct ath_xmit_status *tx_status, struct ath_node *an);
+
+/**********************/
+/* Node / Aggregation */
+/**********************/
+
+/* indicates the node is clened up */
+#define ATH_NODE_CLEAN 0x1
+/* indicates the node is 80211 power save */
+#define ATH_NODE_PWRSAVE 0x2
+
+#define ADDBA_TIMEOUT 200 /* 200 milliseconds */
+#define ADDBA_EXCHANGE_ATTEMPTS 10
+#define ATH_AGGR_DELIM_SZ 4 /* delimiter size */
+#define ATH_AGGR_MINPLEN 256 /* in bytes, minimum packet length */
+/* number of delimiters for encryption padding */
+#define ATH_AGGR_ENCRYPTDELIM 10
+/* minimum h/w qdepth to be sustained to maximize aggregation */
+#define ATH_AGGR_MIN_QDEPTH 2
+#define ATH_AMPDU_SUBFRAME_DEFAULT 32
+#define IEEE80211_SEQ_SEQ_SHIFT 4
+#define IEEE80211_SEQ_MAX 4096
+#define IEEE80211_MIN_AMPDU_BUF 0x8
+
+/* return whether a bit at index _n in bitmap _bm is set
+ * _sz is the size of the bitmap */
+#define ATH_BA_ISSET(_bm, _n) (((_n) < (WME_BA_BMP_SIZE)) && \
+ ((_bm)[(_n) >> 5] & (1 << ((_n) & 31))))
+
+/* return block-ack bitmap index given sequence and starting sequence */
+#define ATH_BA_INDEX(_st, _seq) (((_seq) - (_st)) & (IEEE80211_SEQ_MAX - 1))
+
+/* returns delimiter padding required given the packet length */
+#define ATH_AGGR_GET_NDELIM(_len) \
+ (((((_len) + ATH_AGGR_DELIM_SZ) < ATH_AGGR_MINPLEN) ? \
+ (ATH_AGGR_MINPLEN - (_len) - ATH_AGGR_DELIM_SZ) : 0) >> 2)
+
+#define BAW_WITHIN(_start, _bawsz, _seqno) \
+ ((((_seqno) - (_start)) & 4095) < (_bawsz))
+
+#define ATH_DS_BA_SEQ(_ds) ((_ds)->ds_us.tx.ts_seqnum)
+#define ATH_DS_BA_BITMAP(_ds) (&(_ds)->ds_us.tx.ba_low)
+#define ATH_DS_TX_BA(_ds) ((_ds)->ds_us.tx.ts_flags & ATH9K_TX_BA)
+#define ATH_AN_2_TID(_an, _tidno) (&(_an)->an_aggr.tx.tid[(_tidno)])
+
+enum ATH_AGGR_STATUS {
+ ATH_AGGR_DONE,
+ ATH_AGGR_BAW_CLOSED,
+ ATH_AGGR_LIMITED,
+ ATH_AGGR_SHORTPKT,
+ ATH_AGGR_8K_LIMITED,
+};
+
+enum ATH_AGGR_CHECK {
+ AGGR_NOT_REQUIRED,
+ AGGR_REQUIRED,
+ AGGR_CLEANUP_PROGRESS,
+ AGGR_EXCHANGE_PROGRESS,
+ AGGR_EXCHANGE_DONE
+};
+
+struct aggr_rifs_param {
+ int param_max_frames;
+ int param_max_len;
+ int param_rl;
+ int param_al;
+ struct ath_rc_series *param_rcs;
+};
+
+/* Per-node aggregation state */
+struct ath_node_aggr {
+ struct ath_atx tx; /* node transmit state */
+ struct ath_arx rx; /* node receive state */
+};
+
+/* driver-specific node state */
+struct ath_node {
+ struct list_head list;
+ struct ath_softc *an_sc;
+ atomic_t an_refcnt;
+ struct ath_chainmask_sel an_chainmask_sel;
+ struct ath_node_aggr an_aggr;
+ u8 an_smmode; /* SM Power save mode */
+ u8 an_flags;
+ u8 an_addr[ETH_ALEN];
+};
+
+void ath_tx_resume_tid(struct ath_softc *sc,
+ struct ath_atx_tid *tid);
+enum ATH_AGGR_CHECK ath_tx_aggr_check(struct ath_softc *sc,
+ struct ath_node *an, u8 tidno);
+void ath_tx_aggr_teardown(struct ath_softc *sc,
+ struct ath_node *an, u8 tidno);
+void ath_rx_aggr_teardown(struct ath_softc *sc,
+ struct ath_node *an, u8 tidno);
+int ath_rx_aggr_start(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid,
+ u16 *ssn);
+int ath_rx_aggr_stop(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid);
+int ath_tx_aggr_start(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid,
+ u16 *ssn);
+int ath_tx_aggr_stop(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid);
+void ath_newassoc(struct ath_softc *sc,
+ struct ath_node *node, int isnew, int isuapsd);
+struct ath_node *ath_node_attach(struct ath_softc *sc,
+ u8 addr[ETH_ALEN], int if_id);
+void ath_node_detach(struct ath_softc *sc, struct ath_node *an, bool bh_flag);
+struct ath_node *ath_node_get(struct ath_softc *sc, u8 addr[ETH_ALEN]);
+void ath_node_put(struct ath_softc *sc, struct ath_node *an, bool bh_flag);
+struct ath_node *ath_node_find(struct ath_softc *sc, u8 *addr);
+
+/*******************/
+/* Beacon Handling */
+/*******************/
+
+/*
+ * Regardless of the number of beacons we stagger, (i.e. regardless of the
+ * number of BSSIDs) if a given beacon does not go out even after waiting this
+ * number of beacon intervals, the game's up.
+ */
+#define BSTUCK_THRESH (9 * ATH_BCBUF)
+#define ATH_BCBUF 4 /* number of beacon buffers */
+#define ATH_DEFAULT_BINTVAL 100 /* default beacon interval in TU */
+#define ATH_DEFAULT_BMISS_LIMIT 10
+#define ATH_BEACON_AIFS_DEFAULT 0 /* Default aifs for ap beacon q */
+#define ATH_BEACON_CWMIN_DEFAULT 0 /* Default cwmin for ap beacon q */
+#define ATH_BEACON_CWMAX_DEFAULT 0 /* Default cwmax for ap beacon q */
+#define IEEE80211_MS_TO_TU(x) (((x) * 1000) / 1024)
+
+/* beacon configuration */
+struct ath_beacon_config {
+ u16 beacon_interval;
+ u16 listen_interval;
+ u16 dtim_period;
+ u16 bmiss_timeout;
+ u8 dtim_count;
+ u8 tim_offset;
+ union {
+ u64 last_tsf;
+ u8 last_tstamp[8];
+ } u; /* last received beacon/probe response timestamp of this BSS. */
+};
+
+/* offsets in a beacon frame for
+ * quick acess of beacon content by low-level driver */
+struct ath_beacon_offset {
+ u8 *bo_tim; /* start of atim/dtim */
+};
+
+void ath9k_beacon_tasklet(unsigned long data);
+void ath_beacon_config(struct ath_softc *sc, int if_id);
+int ath_beaconq_setup(struct ath_hal *ah);
+int ath_beacon_alloc(struct ath_softc *sc, int if_id);
+void ath_bstuck_process(struct ath_softc *sc);
+void ath_beacon_tasklet(struct ath_softc *sc, int *needmark);
+void ath_beacon_free(struct ath_softc *sc);
+void ath_beacon_return(struct ath_softc *sc, struct ath_vap *avp);
+void ath_beacon_sync(struct ath_softc *sc, int if_id);
+void ath_update_beacon_info(struct ath_softc *sc, int avgbrssi);
+void ath_get_beaconconfig(struct ath_softc *sc,
+ int if_id,
+ struct ath_beacon_config *conf);
+int ath_update_beacon(struct ath_softc *sc,
+ int if_id,
+ struct ath_beacon_offset *bo,
+ struct sk_buff *skb,
+ int mcast);
+/********/
+/* VAPs */
+/********/
+
+/*
+ * Define the scheme that we select MAC address for multiple
+ * BSS on the same radio. The very first VAP will just use the MAC
+ * address from the EEPROM. For the next 3 VAPs, we set the
+ * U/L bit (bit 1) in MAC address, and use the next two bits as the
+ * index of the VAP.
+ */
+
+#define ATH_SET_VAP_BSSID_MASK(bssid_mask) \
+ ((bssid_mask)[0] &= ~(((ATH_BCBUF-1)<<2)|0x02))
+
+/* VAP configuration (from protocol layer) */
+struct ath_vap_config {
+ u32 av_fixed_rateset;
+ u32 av_fixed_retryset;
+};
+
+/* driver-specific vap state */
+struct ath_vap {
+ struct ieee80211_vif *av_if_data;
+ enum ath9k_opmode av_opmode; /* VAP operational mode */
+ struct ath_buf *av_bcbuf; /* beacon buffer */
+ struct ath_beacon_offset av_boff; /* dynamic update state */
+ struct ath_tx_control av_btxctl; /* txctl information for beacon */
+ int av_bslot; /* beacon slot index */
+ struct ath_txq av_mcastq; /* multicast transmit queue */
+ struct ath_vap_config av_config;/* vap configuration parameters*/
+ struct ath_rate_node *rc_node;
+};
+
+int ath_vap_attach(struct ath_softc *sc,
+ int if_id,
+ struct ieee80211_vif *if_data,
+ enum ath9k_opmode opmode);
+int ath_vap_detach(struct ath_softc *sc, int if_id);
+int ath_vap_config(struct ath_softc *sc,
+ int if_id, struct ath_vap_config *if_config);
+int ath_vap_listen(struct ath_softc *sc, int if_id);
+
+/*********************/
+/* Antenna diversity */
+/*********************/
+
+#define ATH_ANT_DIV_MAX_CFG 2
+#define ATH_ANT_DIV_MIN_IDLE_US 1000000 /* us */
+#define ATH_ANT_DIV_MIN_SCAN_US 50000 /* us */
+
+enum ATH_ANT_DIV_STATE{
+ ATH_ANT_DIV_IDLE,
+ ATH_ANT_DIV_SCAN, /* evaluating antenna */
+};
+
+struct ath_antdiv {
+ struct ath_softc *antdiv_sc;
+ u8 antdiv_start;
+ enum ATH_ANT_DIV_STATE antdiv_state;
+ u8 antdiv_num_antcfg;
+ u8 antdiv_curcfg;
+ u8 antdiv_bestcfg;
+ int32_t antdivf_rssitrig;
+ int32_t antdiv_lastbrssi[ATH_ANT_DIV_MAX_CFG];
+ u64 antdiv_lastbtsf[ATH_ANT_DIV_MAX_CFG];
+ u64 antdiv_laststatetsf;
+ u8 antdiv_bssid[ETH_ALEN];
+};
+
+void ath_slow_ant_div_init(struct ath_antdiv *antdiv,
+ struct ath_softc *sc, int32_t rssitrig);
+void ath_slow_ant_div_start(struct ath_antdiv *antdiv,
+ u8 num_antcfg,
+ const u8 *bssid);
+void ath_slow_ant_div_stop(struct ath_antdiv *antdiv);
+void ath_slow_ant_div(struct ath_antdiv *antdiv,
+ struct ieee80211_hdr *wh,
+ struct ath_rx_status *rx_stats);
+void ath_setdefantenna(void *sc, u32 antenna);
+
+/********************/
+/* Main driver core */
+/********************/
+
+/*
+ * Default cache line size, in bytes.
+ * Used when PCI device not fully initialized by bootrom/BIOS
+*/
+#define DEFAULT_CACHELINE 32
+#define ATH_DEFAULT_NOISE_FLOOR -95
+#define ATH_REGCLASSIDS_MAX 10
+#define ATH_CABQ_READY_TIME 80 /* % of beacon interval */
+#define ATH_PREAMBLE_SHORT (1<<0)
+#define ATH_PROTECT_ENABLE (1<<1)
+#define ATH_MAX_SW_RETRIES 10
+/* Num farmes difference in tx to flip default recv */
+#define ATH_ANTENNA_DIFF 2
+#define ATH_CHAN_MAX 255
+#define IEEE80211_WEP_NKID 4 /* number of key ids */
+#define IEEE80211_RATE_VAL 0x7f
+/*
+ * The key cache is used for h/w cipher state and also for
+ * tracking station state such as the current tx antenna.
+ * We also setup a mapping table between key cache slot indices
+ * and station state to short-circuit node lookups on rx.
+ * Different parts have different size key caches. We handle
+ * up to ATH_KEYMAX entries (could dynamically allocate state).
+ */
+#define ATH_KEYMAX 128 /* max key cache size we handle */
+
+#define RESET_RETRY_TXQ 0x00000001
+#define ATH_IF_ID_ANY 0xff
+
+#define ATH_TXPOWER_MAX 100 /* .5 dBm units */
+
+#define RSSI_LPF_THRESHOLD -20
+#define ATH_RSSI_EP_MULTIPLIER (1<<7) /* pow2 to optimize out * and / */
+#define ATH_RATE_DUMMY_MARKER 0
+#define ATH_RSSI_LPF_LEN 10
+#define ATH_RSSI_DUMMY_MARKER 0x127
+
+#define ATH_EP_MUL(x, mul) ((x) * (mul))
+#define ATH_EP_RND(x, mul) \
+ ((((x)%(mul)) >= ((mul)/2)) ? ((x) + ((mul) - 1)) / (mul) : (x)/(mul))
+#define ATH_RSSI_OUT(x) \
+ (((x) != ATH_RSSI_DUMMY_MARKER) ? \
+ (ATH_EP_RND((x), ATH_RSSI_EP_MULTIPLIER)) : ATH_RSSI_DUMMY_MARKER)
+#define ATH_RSSI_IN(x) \
+ (ATH_EP_MUL((x), ATH_RSSI_EP_MULTIPLIER))
+#define ATH_LPF_RSSI(x, y, len) \
+ ((x != ATH_RSSI_DUMMY_MARKER) ? \
+ (((x) * ((len) - 1) + (y)) / (len)) : (y))
+#define ATH_RSSI_LPF(x, y) do { \
+ if ((y) >= RSSI_LPF_THRESHOLD) \
+ x = ATH_LPF_RSSI((x), \
+ ATH_RSSI_IN((y)), ATH_RSSI_LPF_LEN); \
+ } while (0)
+
+
+enum PROT_MODE {
+ PROT_M_NONE = 0,
+ PROT_M_RTSCTS,
+ PROT_M_CTSONLY
+};
+
+enum RATE_TYPE {
+ NORMAL_RATE = 0,
+ HALF_RATE,
+ QUARTER_RATE
+};
+
+struct ath_ht_info {
+ enum ath9k_ht_macmode tx_chan_width;
+ u16 maxampdu;
+ u8 mpdudensity;
+ u8 ext_chan_offset;
+};
+
+struct ath_softc {
+ struct ieee80211_hw *hw;
+ struct pci_dev *pdev;
+ void __iomem *mem;
+ struct tasklet_struct intr_tq;
+ struct tasklet_struct bcon_tasklet;
+ struct ath_config sc_config; /* load-time parameters */
+ int sc_debug;
+ struct ath_hal *sc_ah;
+ struct ath_rate_softc *sc_rc; /* tx rate control support */
+ u32 sc_intrstatus;
+ enum ath9k_opmode sc_opmode; /* current operating mode */
+
+ u8 sc_invalid; /* being detached */
+ u8 sc_beacons; /* beacons running */
+ u8 sc_scanning; /* scanning active */
+ u8 sc_txaggr; /* enable 11n tx aggregation */
+ u8 sc_rxaggr; /* enable 11n rx aggregation */
+ u8 sc_update_chainmask; /* change chain mask */
+ u8 sc_full_reset; /* force full reset */
+ enum wireless_mode sc_curmode; /* current phy mode */
+ u16 sc_curtxpow;
+ u16 sc_curaid;
+ u8 sc_curbssid[ETH_ALEN];
+ u8 sc_myaddr[ETH_ALEN];
+ enum PROT_MODE sc_protmode;
+ u8 sc_mcastantenna;
+ u8 sc_txantenna; /* data tx antenna (fixed or auto) */
+ u8 sc_nbcnvaps; /* # of vaps sending beacons */
+ u16 sc_nvaps; /* # of active virtual ap's */
+ struct ath_vap *sc_vaps[ATH_BCBUF];
+ enum ath9k_int sc_imask;
+ u8 sc_bssidmask[ETH_ALEN];
+ u8 sc_defant; /* current default antenna */
+ u8 sc_rxotherant; /* rx's on non-default antenna */
+ u16 sc_cachelsz;
+ int sc_slotupdate; /* slot to next advance fsm */
+ int sc_slottime;
+ u8 sc_noreset;
+ int sc_bslot[ATH_BCBUF];
+ struct ath9k_node_stats sc_halstats; /* station-mode rssi stats */
+ struct list_head node_list;
+ struct ath_ht_info sc_ht_info;
+ int16_t sc_noise_floor; /* signal noise floor in dBm */
+ enum ath9k_ht_extprotspacing sc_ht_extprotspacing;
+ u8 sc_tx_chainmask;
+ u8 sc_rx_chainmask;
+ u8 sc_rxchaindetect_ref;
+ u8 sc_rxchaindetect_thresh5GHz;
+ u8 sc_rxchaindetect_thresh2GHz;
+ u8 sc_rxchaindetect_delta5GHz;
+ u8 sc_rxchaindetect_delta2GHz;
+ u32 sc_rtsaggrlimit; /* Chipset specific aggr limit */
+ u32 sc_flags;
+#ifdef CONFIG_SLOW_ANT_DIV
+ struct ath_antdiv sc_antdiv;
+#endif
+ enum {
+ OK, /* no change needed */
+ UPDATE, /* update pending */
+ COMMIT /* beacon sent, commit change */
+ } sc_updateslot; /* slot time update fsm */
+
+ /* Crypto */
+ u32 sc_keymax; /* size of key cache */
+ DECLARE_BITMAP(sc_keymap, ATH_KEYMAX); /* key use bit map */
+ u8 sc_splitmic; /* split TKIP MIC keys */
+ int sc_keytype;
+
+ /* RX */
+ struct list_head sc_rxbuf;
+ struct ath_descdma sc_rxdma;
+ int sc_rxbufsize; /* rx size based on mtu */
+ u32 *sc_rxlink; /* link ptr in last RX desc */
+ u32 sc_rxflush; /* rx flush in progress */
+ u64 sc_lastrx; /* tsf of last rx'd frame */
+
+ /* TX */
+ struct list_head sc_txbuf;
+ struct ath_txq sc_txq[ATH9K_NUM_TX_QUEUES];
+ struct ath_descdma sc_txdma;
+ u32 sc_txqsetup;
+ u32 sc_txintrperiod; /* tx interrupt batching */
+ int sc_haltype2q[ATH9K_WME_AC_VO+1]; /* HAL WME AC -> h/w qnum */
+ u32 sc_ant_tx[8]; /* recent tx frames/antenna */
+
+ /* Beacon */
+ struct ath9k_tx_queue_info sc_beacon_qi;
+ struct ath_descdma sc_bdma;
+ struct ath_txq *sc_cabq;
+ struct list_head sc_bbuf;
+ u32 sc_bhalq;
+ u32 sc_bmisscount;
+ u32 ast_be_xmit; /* beacons transmitted */
+
+ /* Rate */
+ struct ieee80211_rate rates[IEEE80211_NUM_BANDS][ATH_RATE_MAX];
+ const struct ath9k_rate_table *sc_currates;
+ u8 sc_rixmap[256]; /* IEEE to h/w rate table ix */
+ u8 sc_protrix; /* protection rate index */
+ struct {
+ u32 rateKbps; /* transfer rate in kbs */
+ u8 ieeerate; /* IEEE rate */
+ } sc_hwmap[256]; /* h/w rate ix mappings */
+
+ /* Channel, Band */
+ struct ieee80211_channel channels[IEEE80211_NUM_BANDS][ATH_CHAN_MAX];
+ struct ieee80211_supported_band sbands[IEEE80211_NUM_BANDS];
+ struct ath9k_channel sc_curchan;
+
+ /* Locks */
+ spinlock_t sc_rxflushlock;
+ spinlock_t sc_rxbuflock;
+ spinlock_t sc_txbuflock;
+ spinlock_t sc_resetlock;
+ spinlock_t node_lock;
+};
+
+int ath_init(u16 devid, struct ath_softc *sc);
+void ath_deinit(struct ath_softc *sc);
+int ath_open(struct ath_softc *sc, struct ath9k_channel *initial_chan);
+int ath_suspend(struct ath_softc *sc);
+irqreturn_t ath_isr(int irq, void *dev);
+int ath_reset(struct ath_softc *sc);
+void ath_scan_start(struct ath_softc *sc);
+void ath_scan_end(struct ath_softc *sc);
+int ath_set_channel(struct ath_softc *sc, struct ath9k_channel *hchan);
+void ath_setup_rate(struct ath_softc *sc,
+ enum wireless_mode wMode,
+ enum RATE_TYPE type,
+ const struct ath9k_rate_table *rt);
+
+/*********************/
+/* Utility Functions */
+/*********************/
+
+void ath_key_reset(struct ath_softc *sc, u16 keyix, int freeslot);
+int ath_keyset(struct ath_softc *sc,
+ u16 keyix,
+ struct ath9k_keyval *hk,
+ const u8 mac[ETH_ALEN]);
+int ath_get_hal_qnum(u16 queue, struct ath_softc *sc);
+int ath_get_mac80211_qnum(u32 queue, struct ath_softc *sc);
+void ath_setslottime(struct ath_softc *sc);
+void ath_update_txpow(struct ath_softc *sc);
+int ath_cabq_update(struct ath_softc *);
+void ath_get_currentCountry(struct ath_softc *sc,
+ struct ath9k_country_entry *ctry);
+u64 ath_extend_tsf(struct ath_softc *sc, u32 rstamp);
+void ath_internal_reset(struct ath_softc *sc);
+u32 ath_chan2flags(struct ieee80211_channel *chan, struct ath_softc *sc);
+dma_addr_t ath_skb_map_single(struct ath_softc *sc,
+ struct sk_buff *skb,
+ int direction,
+ dma_addr_t *pa);
+void ath_skb_unmap_single(struct ath_softc *sc,
+ struct sk_buff *skb,
+ int direction,
+ dma_addr_t *pa);
+void ath_mcast_merge(struct ath_softc *sc, u32 mfilt[2]);
+enum ath9k_ht_macmode ath_cwm_macmode(struct ath_softc *sc);
+
+#endif /* CORE_H */
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/io.h>
+#include <asm/unaligned.h>
+
+#include "core.h"
+#include "hw.h"
+#include "reg.h"
+#include "phy.h"
+#include "initvals.h"
+
+static void ath9k_hw_iqcal_collect(struct ath_hal *ah);
+static void ath9k_hw_iqcalibrate(struct ath_hal *ah, u8 numChains);
+static void ath9k_hw_adc_gaincal_collect(struct ath_hal *ah);
+static void ath9k_hw_adc_gaincal_calibrate(struct ath_hal *ah,
+ u8 numChains);
+static void ath9k_hw_adc_dccal_collect(struct ath_hal *ah);
+static void ath9k_hw_adc_dccal_calibrate(struct ath_hal *ah,
+ u8 numChains);
+
+static const u8 CLOCK_RATE[] = { 40, 80, 22, 44, 88, 40 };
+static const int16_t NOISE_FLOOR[] = { -96, -93, -98, -96, -93, -96 };
+
+static const struct hal_percal_data iq_cal_multi_sample = {
+ IQ_MISMATCH_CAL,
+ MAX_CAL_SAMPLES,
+ PER_MIN_LOG_COUNT,
+ ath9k_hw_iqcal_collect,
+ ath9k_hw_iqcalibrate
+};
+static const struct hal_percal_data iq_cal_single_sample = {
+ IQ_MISMATCH_CAL,
+ MIN_CAL_SAMPLES,
+ PER_MAX_LOG_COUNT,
+ ath9k_hw_iqcal_collect,
+ ath9k_hw_iqcalibrate
+};
+static const struct hal_percal_data adc_gain_cal_multi_sample = {
+ ADC_GAIN_CAL,
+ MAX_CAL_SAMPLES,
+ PER_MIN_LOG_COUNT,
+ ath9k_hw_adc_gaincal_collect,
+ ath9k_hw_adc_gaincal_calibrate
+};
+static const struct hal_percal_data adc_gain_cal_single_sample = {
+ ADC_GAIN_CAL,
+ MIN_CAL_SAMPLES,
+ PER_MAX_LOG_COUNT,
+ ath9k_hw_adc_gaincal_collect,
+ ath9k_hw_adc_gaincal_calibrate
+};
+static const struct hal_percal_data adc_dc_cal_multi_sample = {
+ ADC_DC_CAL,
+ MAX_CAL_SAMPLES,
+ PER_MIN_LOG_COUNT,
+ ath9k_hw_adc_dccal_collect,
+ ath9k_hw_adc_dccal_calibrate
+};
+static const struct hal_percal_data adc_dc_cal_single_sample = {
+ ADC_DC_CAL,
+ MIN_CAL_SAMPLES,
+ PER_MAX_LOG_COUNT,
+ ath9k_hw_adc_dccal_collect,
+ ath9k_hw_adc_dccal_calibrate
+};
+static const struct hal_percal_data adc_init_dc_cal = {
+ ADC_DC_INIT_CAL,
+ MIN_CAL_SAMPLES,
+ INIT_LOG_COUNT,
+ ath9k_hw_adc_dccal_collect,
+ ath9k_hw_adc_dccal_calibrate
+};
+
+static const struct ath_hal ar5416hal = {
+ AR5416_MAGIC,
+ 0,
+ 0,
+ NULL,
+ NULL,
+ CTRY_DEFAULT,
+ 0,
+ 0,
+ 0,
+ 0,
+ 0,
+ {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+};
+
+static struct ath9k_rate_table ar5416_11a_table = {
+ 8,
+ {0},
+ {
+ {true, PHY_OFDM, 6000, 0x0b, 0x00, (0x80 | 12), 0},
+ {true, PHY_OFDM, 9000, 0x0f, 0x00, 18, 0},
+ {true, PHY_OFDM, 12000, 0x0a, 0x00, (0x80 | 24), 2},
+ {true, PHY_OFDM, 18000, 0x0e, 0x00, 36, 2},
+ {true, PHY_OFDM, 24000, 0x09, 0x00, (0x80 | 48), 4},
+ {true, PHY_OFDM, 36000, 0x0d, 0x00, 72, 4},
+ {true, PHY_OFDM, 48000, 0x08, 0x00, 96, 4},
+ {true, PHY_OFDM, 54000, 0x0c, 0x00, 108, 4}
+ },
+};
+
+static struct ath9k_rate_table ar5416_11b_table = {
+ 4,
+ {0},
+ {
+ {true, PHY_CCK, 1000, 0x1b, 0x00, (0x80 | 2), 0},
+ {true, PHY_CCK, 2000, 0x1a, 0x04, (0x80 | 4), 1},
+ {true, PHY_CCK, 5500, 0x19, 0x04, (0x80 | 11), 1},
+ {true, PHY_CCK, 11000, 0x18, 0x04, (0x80 | 22), 1}
+ },
+};
+
+static struct ath9k_rate_table ar5416_11g_table = {
+ 12,
+ {0},
+ {
+ {true, PHY_CCK, 1000, 0x1b, 0x00, (0x80 | 2), 0},
+ {true, PHY_CCK, 2000, 0x1a, 0x04, (0x80 | 4), 1},
+ {true, PHY_CCK, 5500, 0x19, 0x04, (0x80 | 11), 2},
+ {true, PHY_CCK, 11000, 0x18, 0x04, (0x80 | 22), 3},
+
+ {false, PHY_OFDM, 6000, 0x0b, 0x00, 12, 4},
+ {false, PHY_OFDM, 9000, 0x0f, 0x00, 18, 4},
+ {true, PHY_OFDM, 12000, 0x0a, 0x00, 24, 6},
+ {true, PHY_OFDM, 18000, 0x0e, 0x00, 36, 6},
+ {true, PHY_OFDM, 24000, 0x09, 0x00, 48, 8},
+ {true, PHY_OFDM, 36000, 0x0d, 0x00, 72, 8},
+ {true, PHY_OFDM, 48000, 0x08, 0x00, 96, 8},
+ {true, PHY_OFDM, 54000, 0x0c, 0x00, 108, 8}
+ },
+};
+
+static struct ath9k_rate_table ar5416_11ng_table = {
+ 28,
+ {0},
+ {
+ {true, PHY_CCK, 1000, 0x1b, 0x00, (0x80 | 2), 0},
+ {true, PHY_CCK, 2000, 0x1a, 0x04, (0x80 | 4), 1},
+ {true, PHY_CCK, 5500, 0x19, 0x04, (0x80 | 11), 2},
+ {true, PHY_CCK, 11000, 0x18, 0x04, (0x80 | 22), 3},
+
+ {false, PHY_OFDM, 6000, 0x0b, 0x00, 12, 4},
+ {false, PHY_OFDM, 9000, 0x0f, 0x00, 18, 4},
+ {true, PHY_OFDM, 12000, 0x0a, 0x00, 24, 6},
+ {true, PHY_OFDM, 18000, 0x0e, 0x00, 36, 6},
+ {true, PHY_OFDM, 24000, 0x09, 0x00, 48, 8},
+ {true, PHY_OFDM, 36000, 0x0d, 0x00, 72, 8},
+ {true, PHY_OFDM, 48000, 0x08, 0x00, 96, 8},
+ {true, PHY_OFDM, 54000, 0x0c, 0x00, 108, 8},
+ {true, PHY_HT, 6500, 0x80, 0x00, 0, 4},
+ {true, PHY_HT, 13000, 0x81, 0x00, 1, 6},
+ {true, PHY_HT, 19500, 0x82, 0x00, 2, 6},
+ {true, PHY_HT, 26000, 0x83, 0x00, 3, 8},
+ {true, PHY_HT, 39000, 0x84, 0x00, 4, 8},
+ {true, PHY_HT, 52000, 0x85, 0x00, 5, 8},
+ {true, PHY_HT, 58500, 0x86, 0x00, 6, 8},
+ {true, PHY_HT, 65000, 0x87, 0x00, 7, 8},
+ {true, PHY_HT, 13000, 0x88, 0x00, 8, 4},
+ {true, PHY_HT, 26000, 0x89, 0x00, 9, 6},
+ {true, PHY_HT, 39000, 0x8a, 0x00, 10, 6},
+ {true, PHY_HT, 52000, 0x8b, 0x00, 11, 8},
+ {true, PHY_HT, 78000, 0x8c, 0x00, 12, 8},
+ {true, PHY_HT, 104000, 0x8d, 0x00, 13, 8},
+ {true, PHY_HT, 117000, 0x8e, 0x00, 14, 8},
+ {true, PHY_HT, 130000, 0x8f, 0x00, 15, 8},
+ },
+};
+
+static struct ath9k_rate_table ar5416_11na_table = {
+ 24,
+ {0},
+ {
+ {true, PHY_OFDM, 6000, 0x0b, 0x00, (0x80 | 12), 0},
+ {true, PHY_OFDM, 9000, 0x0f, 0x00, 18, 0},
+ {true, PHY_OFDM, 12000, 0x0a, 0x00, (0x80 | 24), 2},
+ {true, PHY_OFDM, 18000, 0x0e, 0x00, 36, 2},
+ {true, PHY_OFDM, 24000, 0x09, 0x00, (0x80 | 48), 4},
+ {true, PHY_OFDM, 36000, 0x0d, 0x00, 72, 4},
+ {true, PHY_OFDM, 48000, 0x08, 0x00, 96, 4},
+ {true, PHY_OFDM, 54000, 0x0c, 0x00, 108, 4},
+ {true, PHY_HT, 6500, 0x80, 0x00, 0, 0},
+ {true, PHY_HT, 13000, 0x81, 0x00, 1, 2},
+ {true, PHY_HT, 19500, 0x82, 0x00, 2, 2},
+ {true, PHY_HT, 26000, 0x83, 0x00, 3, 4},
+ {true, PHY_HT, 39000, 0x84, 0x00, 4, 4},
+ {true, PHY_HT, 52000, 0x85, 0x00, 5, 4},
+ {true, PHY_HT, 58500, 0x86, 0x00, 6, 4},
+ {true, PHY_HT, 65000, 0x87, 0x00, 7, 4},
+ {true, PHY_HT, 13000, 0x88, 0x00, 8, 0},
+ {true, PHY_HT, 26000, 0x89, 0x00, 9, 2},
+ {true, PHY_HT, 39000, 0x8a, 0x00, 10, 2},
+ {true, PHY_HT, 52000, 0x8b, 0x00, 11, 4},
+ {true, PHY_HT, 78000, 0x8c, 0x00, 12, 4},
+ {true, PHY_HT, 104000, 0x8d, 0x00, 13, 4},
+ {true, PHY_HT, 117000, 0x8e, 0x00, 14, 4},
+ {true, PHY_HT, 130000, 0x8f, 0x00, 15, 4},
+ },
+};
+
+static enum wireless_mode ath9k_hw_chan2wmode(struct ath_hal *ah,
+ const struct ath9k_channel *chan)
+{
+ if (IS_CHAN_CCK(chan))
+ return ATH9K_MODE_11A;
+ if (IS_CHAN_G(chan))
+ return ATH9K_MODE_11G;
+ return ATH9K_MODE_11A;
+}
+
+static bool ath9k_hw_wait(struct ath_hal *ah,
+ u32 reg,
+ u32 mask,
+ u32 val)
+{
+ int i;
+
+ for (i = 0; i < (AH_TIMEOUT / AH_TIME_QUANTUM); i++) {
+ if ((REG_READ(ah, reg) & mask) == val)
+ return true;
+
+ udelay(AH_TIME_QUANTUM);
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_PHY_IO,
+ "%s: timeout on reg 0x%x: 0x%08x & 0x%08x != 0x%08x\n",
+ __func__, reg, REG_READ(ah, reg), mask, val);
+ return false;
+}
+
+static bool ath9k_hw_eeprom_read(struct ath_hal *ah, u32 off,
+ u16 *data)
+{
+ (void) REG_READ(ah, AR5416_EEPROM_OFFSET + (off << AR5416_EEPROM_S));
+
+ if (!ath9k_hw_wait(ah,
+ AR_EEPROM_STATUS_DATA,
+ AR_EEPROM_STATUS_DATA_BUSY |
+ AR_EEPROM_STATUS_DATA_PROT_ACCESS, 0)) {
+ return false;
+ }
+
+ *data = MS(REG_READ(ah, AR_EEPROM_STATUS_DATA),
+ AR_EEPROM_STATUS_DATA_VAL);
+
+ return true;
+}
+
+static int ath9k_hw_flash_map(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ ahp->ah_cal_mem = ioremap(AR5416_EEPROM_START_ADDR, AR5416_EEPROM_MAX);
+
+ if (!ahp->ah_cal_mem) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: cannot remap eeprom region \n", __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static bool ath9k_hw_flash_read(struct ath_hal *ah, u32 off,
+ u16 *data)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ *data = ioread16(ahp->ah_cal_mem + off);
+ return true;
+}
+
+static void ath9k_hw_read_revisions(struct ath_hal *ah)
+{
+ u32 val;
+
+ val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+
+ if (val == 0xFF) {
+ val = REG_READ(ah, AR_SREV);
+
+ ah->ah_macVersion =
+ (val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
+
+ ah->ah_macRev = MS(val, AR_SREV_REVISION2);
+ ah->ah_isPciExpress =
+ (val & AR_SREV_TYPE2_HOST_MODE) ? 0 : 1;
+
+ } else {
+ if (!AR_SREV_9100(ah))
+ ah->ah_macVersion = MS(val, AR_SREV_VERSION);
+
+ ah->ah_macRev = val & AR_SREV_REVISION;
+
+ if (ah->ah_macVersion == AR_SREV_VERSION_5416_PCIE)
+ ah->ah_isPciExpress = true;
+ }
+}
+
+u32 ath9k_hw_reverse_bits(u32 val, u32 n)
+{
+ u32 retval;
+ int i;
+
+ for (i = 0, retval = 0; i < n; i++) {
+ retval = (retval << 1) | (val & 1);
+ val >>= 1;
+ }
+ return retval;
+}
+
+static void ath9k_hw_set_defaults(struct ath_hal *ah)
+{
+ int i;
+
+ ah->ah_config.dma_beacon_response_time = 2;
+ ah->ah_config.sw_beacon_response_time = 10;
+ ah->ah_config.additional_swba_backoff = 0;
+ ah->ah_config.ack_6mb = 0x0;
+ ah->ah_config.cwm_ignore_extcca = 0;
+ ah->ah_config.pcie_powersave_enable = 0;
+ ah->ah_config.pcie_l1skp_enable = 0;
+ ah->ah_config.pcie_clock_req = 0;
+ ah->ah_config.pcie_power_reset = 0x100;
+ ah->ah_config.pcie_restore = 0;
+ ah->ah_config.pcie_waen = 0;
+ ah->ah_config.analog_shiftreg = 1;
+ ah->ah_config.ht_enable = 1;
+ ah->ah_config.ofdm_trig_low = 200;
+ ah->ah_config.ofdm_trig_high = 500;
+ ah->ah_config.cck_trig_high = 200;
+ ah->ah_config.cck_trig_low = 100;
+ ah->ah_config.enable_ani = 0;
+ ah->ah_config.noise_immunity_level = 4;
+ ah->ah_config.ofdm_weaksignal_det = 1;
+ ah->ah_config.cck_weaksignal_thr = 0;
+ ah->ah_config.spur_immunity_level = 2;
+ ah->ah_config.firstep_level = 0;
+ ah->ah_config.rssi_thr_high = 40;
+ ah->ah_config.rssi_thr_low = 7;
+ ah->ah_config.diversity_control = 0;
+ ah->ah_config.antenna_switch_swap = 0;
+
+ for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) {
+ ah->ah_config.spurchans[i][0] = AR_NO_SPUR;
+ ah->ah_config.spurchans[i][1] = AR_NO_SPUR;
+ }
+
+ ah->ah_config.intr_mitigation = 0;
+}
+
+static inline void ath9k_hw_override_ini(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ if (!AR_SREV_5416_V20_OR_LATER(ah)
+ || AR_SREV_9280_10_OR_LATER(ah))
+ return;
+
+ REG_WRITE(ah, 0x9800 + (651 << 2), 0x11);
+}
+
+static inline void ath9k_hw_init_bb(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ u32 synthDelay;
+
+ synthDelay = REG_READ(ah, AR_PHY_RX_DELAY) & AR_PHY_RX_DELAY_DELAY;
+ if (IS_CHAN_CCK(chan))
+ synthDelay = (4 * synthDelay) / 22;
+ else
+ synthDelay /= 10;
+
+ REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN);
+
+ udelay(synthDelay + BASE_ACTIVATE_DELAY);
+}
+
+static inline void ath9k_hw_init_interrupt_masks(struct ath_hal *ah,
+ enum ath9k_opmode opmode)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ ahp->ah_maskReg = AR_IMR_TXERR |
+ AR_IMR_TXURN |
+ AR_IMR_RXERR |
+ AR_IMR_RXORN |
+ AR_IMR_BCNMISC;
+
+ if (ahp->ah_intrMitigation)
+ ahp->ah_maskReg |= AR_IMR_RXINTM | AR_IMR_RXMINTR;
+ else
+ ahp->ah_maskReg |= AR_IMR_RXOK;
+
+ ahp->ah_maskReg |= AR_IMR_TXOK;
+
+ if (opmode == ATH9K_M_HOSTAP)
+ ahp->ah_maskReg |= AR_IMR_MIB;
+
+ REG_WRITE(ah, AR_IMR, ahp->ah_maskReg);
+ REG_WRITE(ah, AR_IMR_S2, REG_READ(ah, AR_IMR_S2) | AR_IMR_S2_GTT);
+
+ if (!AR_SREV_9100(ah)) {
+ REG_WRITE(ah, AR_INTR_SYNC_CAUSE, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_INTR_SYNC_ENABLE, AR_INTR_SYNC_DEFAULT);
+ REG_WRITE(ah, AR_INTR_SYNC_MASK, 0);
+ }
+}
+
+static inline void ath9k_hw_init_qos(struct ath_hal *ah)
+{
+ REG_WRITE(ah, AR_MIC_QOS_CONTROL, 0x100aa);
+ REG_WRITE(ah, AR_MIC_QOS_SELECT, 0x3210);
+
+ REG_WRITE(ah, AR_QOS_NO_ACK,
+ SM(2, AR_QOS_NO_ACK_TWO_BIT) |
+ SM(5, AR_QOS_NO_ACK_BIT_OFF) |
+ SM(0, AR_QOS_NO_ACK_BYTE_OFF));
+
+ REG_WRITE(ah, AR_TXOP_X, AR_TXOP_X_VAL);
+ REG_WRITE(ah, AR_TXOP_0_3, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_TXOP_4_7, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_TXOP_8_11, 0xFFFFFFFF);
+ REG_WRITE(ah, AR_TXOP_12_15, 0xFFFFFFFF);
+}
+
+static void ath9k_hw_analog_shift_rmw(struct ath_hal *ah,
+ u32 reg,
+ u32 mask,
+ u32 shift,
+ u32 val)
+{
+ u32 regVal;
+
+ regVal = REG_READ(ah, reg) & ~mask;
+ regVal |= (val << shift) & mask;
+
+ REG_WRITE(ah, reg, regVal);
+
+ if (ah->ah_config.analog_shiftreg)
+ udelay(100);
+
+ return;
+}
+
+static u8 ath9k_hw_get_num_ant_config(struct ath_hal_5416 *ahp,
+ enum ieee80211_band freq_band)
+{
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ struct modal_eep_header *pModal =
+ &(eep->modalHeader[IEEE80211_BAND_5GHZ == freq_band]);
+ struct base_eep_header *pBase = &eep->baseEepHeader;
+ u8 num_ant_config;
+
+ num_ant_config = 1;
+
+ if (pBase->version >= 0x0E0D)
+ if (pModal->useAnt1)
+ num_ant_config += 1;
+
+ return num_ant_config;
+}
+
+static int
+ath9k_hw_get_eeprom_antenna_cfg(struct ath_hal_5416 *ahp,
+ struct ath9k_channel *chan,
+ u8 index,
+ u16 *config)
+{
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ struct modal_eep_header *pModal =
+ &(eep->modalHeader[IS_CHAN_2GHZ(chan)]);
+ struct base_eep_header *pBase = &eep->baseEepHeader;
+
+ switch (index) {
+ case 0:
+ *config = pModal->antCtrlCommon & 0xFFFF;
+ return 0;
+ case 1:
+ if (pBase->version >= 0x0E0D) {
+ if (pModal->useAnt1) {
+ *config =
+ ((pModal->antCtrlCommon & 0xFFFF0000) >> 16);
+ return 0;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+
+ return -EINVAL;
+}
+
+static inline bool ath9k_hw_nvram_read(struct ath_hal *ah,
+ u32 off,
+ u16 *data)
+{
+ if (ath9k_hw_use_flash(ah))
+ return ath9k_hw_flash_read(ah, off, data);
+ else
+ return ath9k_hw_eeprom_read(ah, off, data);
+}
+
+static inline bool ath9k_hw_fill_eeprom(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ u16 *eep_data;
+ int addr, ar5416_eep_start_loc = 0;
+
+ if (!ath9k_hw_use_flash(ah)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: Reading from EEPROM, not flash\n", __func__);
+ ar5416_eep_start_loc = 256;
+ }
+ if (AR_SREV_9100(ah))
+ ar5416_eep_start_loc = 256;
+
+ eep_data = (u16 *) eep;
+ for (addr = 0;
+ addr < sizeof(struct ar5416_eeprom) / sizeof(u16);
+ addr++) {
+ if (!ath9k_hw_nvram_read(ah, addr + ar5416_eep_start_loc,
+ eep_data)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: Unable to read eeprom region \n",
+ __func__);
+ return false;
+ }
+ eep_data++;
+ }
+ return true;
+}
+
+/* XXX: Clean me up, make me more legible */
+static bool
+ath9k_hw_eeprom_set_board_values(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct modal_eep_header *pModal;
+ int i, regChainOffset;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ u8 txRxAttenLocal;
+ u16 ant_config;
+
+ pModal = &(eep->modalHeader[IS_CHAN_2GHZ(chan)]);
+
+ txRxAttenLocal = IS_CHAN_2GHZ(chan) ? 23 : 44;
+
+ ath9k_hw_get_eeprom_antenna_cfg(ahp, chan, 1, &ant_config);
+ REG_WRITE(ah, AR_PHY_SWITCH_COM, ant_config);
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ if (AR_SREV_9280(ah)) {
+ if (i >= 2)
+ break;
+ }
+
+ if (AR_SREV_5416_V20_OR_LATER(ah) &&
+ (ahp->ah_rxchainmask == 5 || ahp->ah_txchainmask == 5)
+ && (i != 0))
+ regChainOffset = (i == 1) ? 0x2000 : 0x1000;
+ else
+ regChainOffset = i * 0x1000;
+
+ REG_WRITE(ah, AR_PHY_SWITCH_CHAIN_0 + regChainOffset,
+ pModal->antCtrlChain[i]);
+
+ REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0) + regChainOffset,
+ (REG_READ(ah,
+ AR_PHY_TIMING_CTRL4(0) +
+ regChainOffset) &
+ ~(AR_PHY_TIMING_CTRL4_IQCORR_Q_Q_COFF |
+ AR_PHY_TIMING_CTRL4_IQCORR_Q_I_COFF)) |
+ SM(pModal->iqCalICh[i],
+ AR_PHY_TIMING_CTRL4_IQCORR_Q_I_COFF) |
+ SM(pModal->iqCalQCh[i],
+ AR_PHY_TIMING_CTRL4_IQCORR_Q_Q_COFF));
+
+ if ((i == 0) || AR_SREV_5416_V20_OR_LATER(ah)) {
+ if ((eep->baseEepHeader.version &
+ AR5416_EEP_VER_MINOR_MASK) >=
+ AR5416_EEP_MINOR_VER_3) {
+ txRxAttenLocal = pModal->txRxAttenCh[i];
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ REG_RMW_FIELD(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ AR_PHY_GAIN_2GHZ_XATTEN1_MARGIN,
+ pModal->
+ bswMargin[i]);
+ REG_RMW_FIELD(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ AR_PHY_GAIN_2GHZ_XATTEN1_DB,
+ pModal->
+ bswAtten[i]);
+ REG_RMW_FIELD(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ AR_PHY_GAIN_2GHZ_XATTEN2_MARGIN,
+ pModal->
+ xatten2Margin[i]);
+ REG_RMW_FIELD(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ AR_PHY_GAIN_2GHZ_XATTEN2_DB,
+ pModal->
+ xatten2Db[i]);
+ } else {
+ REG_WRITE(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ (REG_READ(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset) &
+ ~AR_PHY_GAIN_2GHZ_BSW_MARGIN)
+ | SM(pModal->
+ bswMargin[i],
+ AR_PHY_GAIN_2GHZ_BSW_MARGIN));
+ REG_WRITE(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ (REG_READ(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset) &
+ ~AR_PHY_GAIN_2GHZ_BSW_ATTEN)
+ | SM(pModal->bswAtten[i],
+ AR_PHY_GAIN_2GHZ_BSW_ATTEN));
+ }
+ }
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ REG_RMW_FIELD(ah,
+ AR_PHY_RXGAIN +
+ regChainOffset,
+ AR9280_PHY_RXGAIN_TXRX_ATTEN,
+ txRxAttenLocal);
+ REG_RMW_FIELD(ah,
+ AR_PHY_RXGAIN +
+ regChainOffset,
+ AR9280_PHY_RXGAIN_TXRX_MARGIN,
+ pModal->rxTxMarginCh[i]);
+ } else {
+ REG_WRITE(ah,
+ AR_PHY_RXGAIN + regChainOffset,
+ (REG_READ(ah,
+ AR_PHY_RXGAIN +
+ regChainOffset) &
+ ~AR_PHY_RXGAIN_TXRX_ATTEN) |
+ SM(txRxAttenLocal,
+ AR_PHY_RXGAIN_TXRX_ATTEN));
+ REG_WRITE(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset,
+ (REG_READ(ah,
+ AR_PHY_GAIN_2GHZ +
+ regChainOffset) &
+ ~AR_PHY_GAIN_2GHZ_RXTX_MARGIN) |
+ SM(pModal->rxTxMarginCh[i],
+ AR_PHY_GAIN_2GHZ_RXTX_MARGIN));
+ }
+ }
+ }
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ if (IS_CHAN_2GHZ(chan)) {
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF2G1_CH0,
+ AR_AN_RF2G1_CH0_OB,
+ AR_AN_RF2G1_CH0_OB_S,
+ pModal->ob);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF2G1_CH0,
+ AR_AN_RF2G1_CH0_DB,
+ AR_AN_RF2G1_CH0_DB_S,
+ pModal->db);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF2G1_CH1,
+ AR_AN_RF2G1_CH1_OB,
+ AR_AN_RF2G1_CH1_OB_S,
+ pModal->ob_ch1);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF2G1_CH1,
+ AR_AN_RF2G1_CH1_DB,
+ AR_AN_RF2G1_CH1_DB_S,
+ pModal->db_ch1);
+ } else {
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF5G1_CH0,
+ AR_AN_RF5G1_CH0_OB5,
+ AR_AN_RF5G1_CH0_OB5_S,
+ pModal->ob);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF5G1_CH0,
+ AR_AN_RF5G1_CH0_DB5,
+ AR_AN_RF5G1_CH0_DB5_S,
+ pModal->db);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF5G1_CH1,
+ AR_AN_RF5G1_CH1_OB5,
+ AR_AN_RF5G1_CH1_OB5_S,
+ pModal->ob_ch1);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_RF5G1_CH1,
+ AR_AN_RF5G1_CH1_DB5,
+ AR_AN_RF5G1_CH1_DB5_S,
+ pModal->db_ch1);
+ }
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_TOP2,
+ AR_AN_TOP2_XPABIAS_LVL,
+ AR_AN_TOP2_XPABIAS_LVL_S,
+ pModal->xpaBiasLvl);
+ ath9k_hw_analog_shift_rmw(ah, AR_AN_TOP2,
+ AR_AN_TOP2_LOCALBIAS,
+ AR_AN_TOP2_LOCALBIAS_S,
+ pModal->local_bias);
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY, "ForceXPAon: %d\n",
+ pModal->force_xpaon);
+ REG_RMW_FIELD(ah, AR_PHY_XPA_CFG, AR_PHY_FORCE_XPA_CFG,
+ pModal->force_xpaon);
+ }
+
+ REG_RMW_FIELD(ah, AR_PHY_SETTLING, AR_PHY_SETTLING_SWITCH,
+ pModal->switchSettling);
+ REG_RMW_FIELD(ah, AR_PHY_DESIRED_SZ, AR_PHY_DESIRED_SZ_ADC,
+ pModal->adcDesiredSize);
+
+ if (!AR_SREV_9280_10_OR_LATER(ah))
+ REG_RMW_FIELD(ah, AR_PHY_DESIRED_SZ,
+ AR_PHY_DESIRED_SZ_PGA,
+ pModal->pgaDesiredSize);
+
+ REG_WRITE(ah, AR_PHY_RF_CTL4,
+ SM(pModal->txEndToXpaOff, AR_PHY_RF_CTL4_TX_END_XPAA_OFF)
+ | SM(pModal->txEndToXpaOff,
+ AR_PHY_RF_CTL4_TX_END_XPAB_OFF)
+ | SM(pModal->txFrameToXpaOn,
+ AR_PHY_RF_CTL4_FRAME_XPAA_ON)
+ | SM(pModal->txFrameToXpaOn,
+ AR_PHY_RF_CTL4_FRAME_XPAB_ON));
+
+ REG_RMW_FIELD(ah, AR_PHY_RF_CTL3, AR_PHY_TX_END_TO_A2_RX_ON,
+ pModal->txEndToRxOn);
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ REG_RMW_FIELD(ah, AR_PHY_CCA, AR9280_PHY_CCA_THRESH62,
+ pModal->thresh62);
+ REG_RMW_FIELD(ah, AR_PHY_EXT_CCA0,
+ AR_PHY_EXT_CCA0_THRESH62,
+ pModal->thresh62);
+ } else {
+ REG_RMW_FIELD(ah, AR_PHY_CCA, AR_PHY_CCA_THRESH62,
+ pModal->thresh62);
+ REG_RMW_FIELD(ah, AR_PHY_EXT_CCA,
+ AR_PHY_EXT_CCA_THRESH62,
+ pModal->thresh62);
+ }
+
+ if ((eep->baseEepHeader.version & AR5416_EEP_VER_MINOR_MASK) >=
+ AR5416_EEP_MINOR_VER_2) {
+ REG_RMW_FIELD(ah, AR_PHY_RF_CTL2,
+ AR_PHY_TX_END_DATA_START,
+ pModal->txFrameToDataStart);
+ REG_RMW_FIELD(ah, AR_PHY_RF_CTL2, AR_PHY_TX_END_PA_ON,
+ pModal->txFrameToPaOn);
+ }
+
+ if ((eep->baseEepHeader.version & AR5416_EEP_VER_MINOR_MASK) >=
+ AR5416_EEP_MINOR_VER_3) {
+ if (IS_CHAN_HT40(chan))
+ REG_RMW_FIELD(ah, AR_PHY_SETTLING,
+ AR_PHY_SETTLING_SWITCH,
+ pModal->swSettleHt40);
+ }
+
+ return true;
+}
+
+static inline int ath9k_hw_check_eeprom(struct ath_hal *ah)
+{
+ u32 sum = 0, el;
+ u16 *eepdata;
+ int i;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ bool need_swap = false;
+ struct ar5416_eeprom *eep =
+ (struct ar5416_eeprom *) &ahp->ah_eeprom;
+
+ if (!ath9k_hw_use_flash(ah)) {
+ u16 magic, magic2;
+ int addr;
+
+ if (!ath9k_hw_nvram_read(ah, AR5416_EEPROM_MAGIC_OFFSET,
+ &magic)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: Reading Magic # failed\n", __func__);
+ return false;
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM, "%s: Read Magic = 0x%04X\n",
+ __func__, magic);
+
+ if (magic != AR5416_EEPROM_MAGIC) {
+ magic2 = swab16(magic);
+
+ if (magic2 == AR5416_EEPROM_MAGIC) {
+ need_swap = true;
+ eepdata = (u16 *) (&ahp->ah_eeprom);
+
+ for (addr = 0;
+ addr <
+ sizeof(struct ar5416_eeprom) /
+ sizeof(u16); addr++) {
+ u16 temp;
+
+ temp = swab16(*eepdata);
+ *eepdata = temp;
+ eepdata++;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "0x%04X ", *eepdata);
+ if (((addr + 1) % 6) == 0)
+ DPRINTF(ah->ah_sc,
+ ATH_DBG_EEPROM,
+ "\n");
+ }
+ } else {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "Invalid EEPROM Magic. "
+ "endianness missmatch.\n");
+ return -EINVAL;
+ }
+ }
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM, "need_swap = %s.\n",
+ need_swap ? "True" : "False");
+
+ if (need_swap)
+ el = swab16(ahp->ah_eeprom.baseEepHeader.length);
+ else
+ el = ahp->ah_eeprom.baseEepHeader.length;
+
+ if (el > sizeof(struct ar5416_eeprom))
+ el = sizeof(struct ar5416_eeprom) / sizeof(u16);
+ else
+ el = el / sizeof(u16);
+
+ eepdata = (u16 *) (&ahp->ah_eeprom);
+
+ for (i = 0; i < el; i++)
+ sum ^= *eepdata++;
+
+ if (need_swap) {
+ u32 integer, j;
+ u16 word;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "EEPROM Endianness is not native.. Changing \n");
+
+ word = swab16(eep->baseEepHeader.length);
+ eep->baseEepHeader.length = word;
+
+ word = swab16(eep->baseEepHeader.checksum);
+ eep->baseEepHeader.checksum = word;
+
+ word = swab16(eep->baseEepHeader.version);
+ eep->baseEepHeader.version = word;
+
+ word = swab16(eep->baseEepHeader.regDmn[0]);
+ eep->baseEepHeader.regDmn[0] = word;
+
+ word = swab16(eep->baseEepHeader.regDmn[1]);
+ eep->baseEepHeader.regDmn[1] = word;
+
+ word = swab16(eep->baseEepHeader.rfSilent);
+ eep->baseEepHeader.rfSilent = word;
+
+ word = swab16(eep->baseEepHeader.blueToothOptions);
+ eep->baseEepHeader.blueToothOptions = word;
+
+ word = swab16(eep->baseEepHeader.deviceCap);
+ eep->baseEepHeader.deviceCap = word;
+
+ for (j = 0; j < ARRAY_SIZE(eep->modalHeader); j++) {
+ struct modal_eep_header *pModal =
+ &eep->modalHeader[j];
+ integer = swab32(pModal->antCtrlCommon);
+ pModal->antCtrlCommon = integer;
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ integer = swab32(pModal->antCtrlChain[i]);
+ pModal->antCtrlChain[i] = integer;
+ }
+
+ for (i = 0; i < AR5416_EEPROM_MODAL_SPURS; i++) {
+ word = swab16(pModal->spurChans[i].spurChan);
+ pModal->spurChans[i].spurChan = word;
+ }
+ }
+ }
+
+ if (sum != 0xffff || ar5416_get_eep_ver(ahp) != AR5416_EEP_VER ||
+ ar5416_get_eep_rev(ahp) < AR5416_EEP_NO_BACK_VER) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "Bad EEPROM checksum 0x%x or revision 0x%04x\n",
+ sum, ar5416_get_eep_ver(ahp));
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static bool ath9k_hw_chip_test(struct ath_hal *ah)
+{
+ u32 regAddr[2] = { AR_STA_ID0, AR_PHY_BASE + (8 << 2) };
+ u32 regHold[2];
+ u32 patternData[4] = { 0x55555555,
+ 0xaaaaaaaa,
+ 0x66666666,
+ 0x99999999 };
+ int i, j;
+
+ for (i = 0; i < 2; i++) {
+ u32 addr = regAddr[i];
+ u32 wrData, rdData;
+
+ regHold[i] = REG_READ(ah, addr);
+ for (j = 0; j < 0x100; j++) {
+ wrData = (j << 16) | j;
+ REG_WRITE(ah, addr, wrData);
+ rdData = REG_READ(ah, addr);
+ if (rdData != wrData) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "%s: address test failed "
+ "addr: 0x%08x - wr:0x%08x != rd:0x%08x\n",
+ __func__, addr, wrData, rdData);
+ return false;
+ }
+ }
+ for (j = 0; j < 4; j++) {
+ wrData = patternData[j];
+ REG_WRITE(ah, addr, wrData);
+ rdData = REG_READ(ah, addr);
+ if (wrData != rdData) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "%s: address test failed "
+ "addr: 0x%08x - wr:0x%08x != rd:0x%08x\n",
+ __func__, addr, wrData, rdData);
+ return false;
+ }
+ }
+ REG_WRITE(ah, regAddr[i], regHold[i]);
+ }
+ udelay(100);
+ return true;
+}
+
+u32 ath9k_hw_getrxfilter(struct ath_hal *ah)
+{
+ u32 bits = REG_READ(ah, AR_RX_FILTER);
+ u32 phybits = REG_READ(ah, AR_PHY_ERR);
+
+ if (phybits & AR_PHY_ERR_RADAR)
+ bits |= ATH9K_RX_FILTER_PHYRADAR;
+ if (phybits & (AR_PHY_ERR_OFDM_TIMING | AR_PHY_ERR_CCK_TIMING))
+ bits |= ATH9K_RX_FILTER_PHYERR;
+ return bits;
+}
+
+void ath9k_hw_setrxfilter(struct ath_hal *ah, u32 bits)
+{
+ u32 phybits;
+
+ REG_WRITE(ah, AR_RX_FILTER, (bits & 0xffff) | AR_RX_COMPR_BAR);
+ phybits = 0;
+ if (bits & ATH9K_RX_FILTER_PHYRADAR)
+ phybits |= AR_PHY_ERR_RADAR;
+ if (bits & ATH9K_RX_FILTER_PHYERR)
+ phybits |= AR_PHY_ERR_OFDM_TIMING | AR_PHY_ERR_CCK_TIMING;
+ REG_WRITE(ah, AR_PHY_ERR, phybits);
+
+ if (phybits)
+ REG_WRITE(ah, AR_RXCFG,
+ REG_READ(ah, AR_RXCFG) | AR_RXCFG_ZLFDMA);
+ else
+ REG_WRITE(ah, AR_RXCFG,
+ REG_READ(ah, AR_RXCFG) & ~AR_RXCFG_ZLFDMA);
+}
+
+bool ath9k_hw_setcapability(struct ath_hal *ah,
+ enum ath9k_capability_type type,
+ u32 capability,
+ u32 setting,
+ int *status)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 v;
+
+ switch (type) {
+ case ATH9K_CAP_TKIP_MIC:
+ if (setting)
+ ahp->ah_staId1Defaults |=
+ AR_STA_ID1_CRPT_MIC_ENABLE;
+ else
+ ahp->ah_staId1Defaults &=
+ ~AR_STA_ID1_CRPT_MIC_ENABLE;
+ return true;
+ case ATH9K_CAP_DIVERSITY:
+ v = REG_READ(ah, AR_PHY_CCK_DETECT);
+ if (setting)
+ v |= AR_PHY_CCK_DETECT_BB_ENABLE_ANT_FAST_DIV;
+ else
+ v &= ~AR_PHY_CCK_DETECT_BB_ENABLE_ANT_FAST_DIV;
+ REG_WRITE(ah, AR_PHY_CCK_DETECT, v);
+ return true;
+ case ATH9K_CAP_MCAST_KEYSRCH:
+ if (setting)
+ ahp->ah_staId1Defaults |= AR_STA_ID1_MCAST_KSRCH;
+ else
+ ahp->ah_staId1Defaults &= ~AR_STA_ID1_MCAST_KSRCH;
+ return true;
+ case ATH9K_CAP_TSF_ADJUST:
+ if (setting)
+ ahp->ah_miscMode |= AR_PCU_TX_ADD_TSF;
+ else
+ ahp->ah_miscMode &= ~AR_PCU_TX_ADD_TSF;
+ return true;
+ default:
+ return false;
+ }
+}
+
+void ath9k_hw_dmaRegDump(struct ath_hal *ah)
+{
+ u32 val[ATH9K_NUM_DMA_DEBUG_REGS];
+ int qcuOffset = 0, dcuOffset = 0;
+ u32 *qcuBase = &val[0], *dcuBase = &val[4];
+ int i;
+
+ REG_WRITE(ah, AR_MACMISC,
+ ((AR_MACMISC_DMA_OBS_LINE_8 << AR_MACMISC_DMA_OBS_S) |
+ (AR_MACMISC_MISC_OBS_BUS_1 <<
+ AR_MACMISC_MISC_OBS_BUS_MSB_S)));
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "Raw DMA Debug values:\n");
+ for (i = 0; i < ATH9K_NUM_DMA_DEBUG_REGS; i++) {
+ if (i % 4 == 0)
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "\n");
+
+ val[i] = REG_READ(ah, AR_DMADBG_0 + (i * sizeof(u32)));
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "%d: %08x ", i, val[i]);
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "\n\n");
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "Num QCU: chain_st fsp_ok fsp_st DCU: chain_st\n");
+
+ for (i = 0; i < ATH9K_NUM_QUEUES;
+ i++, qcuOffset += 4, dcuOffset += 5) {
+ if (i == 8) {
+ qcuOffset = 0;
+ qcuBase++;
+ }
+
+ if (i == 6) {
+ dcuOffset = 0;
+ dcuBase++;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "%2d %2x %1x %2x %2x\n",
+ i, (*qcuBase & (0x7 << qcuOffset)) >> qcuOffset,
+ (*qcuBase & (0x8 << qcuOffset)) >> (qcuOffset +
+ 3),
+ val[2] & (0x7 << (i * 3)) >> (i * 3),
+ (*dcuBase & (0x1f << dcuOffset)) >> dcuOffset);
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "\n");
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "qcu_stitch state: %2x qcu_fetch state: %2x\n",
+ (val[3] & 0x003c0000) >> 18, (val[3] & 0x03c00000) >> 22);
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "qcu_complete state: %2x dcu_complete state: %2x\n",
+ (val[3] & 0x1c000000) >> 26, (val[6] & 0x3));
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "dcu_arb state: %2x dcu_fp state: %2x\n",
+ (val[5] & 0x06000000) >> 25, (val[5] & 0x38000000) >> 27);
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "chan_idle_dur: %3d chan_idle_dur_valid: %1d\n",
+ (val[6] & 0x000003fc) >> 2, (val[6] & 0x00000400) >> 10);
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "txfifo_valid_0: %1d txfifo_valid_1: %1d\n",
+ (val[6] & 0x00000800) >> 11, (val[6] & 0x00001000) >> 12);
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "txfifo_dcu_num_0: %2d txfifo_dcu_num_1: %2d\n",
+ (val[6] & 0x0001e000) >> 13, (val[6] & 0x001e0000) >> 17);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO, "pcu observe 0x%x \n",
+ REG_READ(ah, AR_OBS_BUS_1));
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "AR_CR 0x%x \n", REG_READ(ah, AR_CR));
+}
+
+u32 ath9k_hw_GetMibCycleCountsPct(struct ath_hal *ah,
+ u32 *rxc_pcnt,
+ u32 *rxf_pcnt,
+ u32 *txf_pcnt)
+{
+ static u32 cycles, rx_clear, rx_frame, tx_frame;
+ u32 good = 1;
+
+ u32 rc = REG_READ(ah, AR_RCCNT);
+ u32 rf = REG_READ(ah, AR_RFCNT);
+ u32 tf = REG_READ(ah, AR_TFCNT);
+ u32 cc = REG_READ(ah, AR_CCCNT);
+
+ if (cycles == 0 || cycles > cc) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: cycle counter wrap. ExtBusy = 0\n",
+ __func__);
+ good = 0;
+ } else {
+ u32 cc_d = cc - cycles;
+ u32 rc_d = rc - rx_clear;
+ u32 rf_d = rf - rx_frame;
+ u32 tf_d = tf - tx_frame;
+
+ if (cc_d != 0) {
+ *rxc_pcnt = rc_d * 100 / cc_d;
+ *rxf_pcnt = rf_d * 100 / cc_d;
+ *txf_pcnt = tf_d * 100 / cc_d;
+ } else {
+ good = 0;
+ }
+ }
+
+ cycles = cc;
+ rx_frame = rf;
+ rx_clear = rc;
+ tx_frame = tf;
+
+ return good;
+}
+
+void ath9k_hw_set11nmac2040(struct ath_hal *ah, enum ath9k_ht_macmode mode)
+{
+ u32 macmode;
+
+ if (mode == ATH9K_HT_MACMODE_2040 &&
+ !ah->ah_config.cwm_ignore_extcca)
+ macmode = AR_2040_JOINED_RX_CLEAR;
+ else
+ macmode = 0;
+
+ REG_WRITE(ah, AR_2040_MODE, macmode);
+}
+
+static void ath9k_hw_mark_phy_inactive(struct ath_hal *ah)
+{
+ REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_DIS);
+}
+
+
+static struct ath_hal_5416 *ath9k_hw_newstate(u16 devid,
+ struct ath_softc *sc,
+ void __iomem *mem,
+ int *status)
+{
+ static const u8 defbssidmask[ETH_ALEN] =
+ { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
+ struct ath_hal_5416 *ahp;
+ struct ath_hal *ah;
+
+ ahp = kzalloc(sizeof(struct ath_hal_5416), GFP_KERNEL);
+ if (ahp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: cannot allocate memory for state block\n",
+ __func__);
+ *status = -ENOMEM;
+ return NULL;
+ }
+
+ ah = &ahp->ah;
+
+ memcpy(&ahp->ah, &ar5416hal, sizeof(struct ath_hal));
+
+ ah->ah_sc = sc;
+ ah->ah_sh = mem;
+
+ ah->ah_devid = devid;
+ ah->ah_subvendorid = 0;
+
+ ah->ah_flags = 0;
+ if ((devid == AR5416_AR9100_DEVID))
+ ah->ah_macVersion = AR_SREV_VERSION_9100;
+ if (!AR_SREV_9100(ah))
+ ah->ah_flags = AH_USE_EEPROM;
+
+ ah->ah_powerLimit = MAX_RATE_POWER;
+ ah->ah_tpScale = ATH9K_TP_SCALE_MAX;
+
+ ahp->ah_atimWindow = 0;
+ ahp->ah_diversityControl = ah->ah_config.diversity_control;
+ ahp->ah_antennaSwitchSwap =
+ ah->ah_config.antenna_switch_swap;
+
+ ahp->ah_staId1Defaults = AR_STA_ID1_CRPT_MIC_ENABLE;
+ ahp->ah_beaconInterval = 100;
+ ahp->ah_enable32kHzClock = DONT_USE_32KHZ;
+ ahp->ah_slottime = (u32) -1;
+ ahp->ah_acktimeout = (u32) -1;
+ ahp->ah_ctstimeout = (u32) -1;
+ ahp->ah_globaltxtimeout = (u32) -1;
+ memcpy(&ahp->ah_bssidmask, defbssidmask, ETH_ALEN);
+
+ ahp->ah_gBeaconRate = 0;
+
+ return ahp;
+}
+
+static int ath9k_hw_eeprom_attach(struct ath_hal *ah)
+{
+ int status;
+
+ if (ath9k_hw_use_flash(ah))
+ ath9k_hw_flash_map(ah);
+
+ if (!ath9k_hw_fill_eeprom(ah))
+ return -EIO;
+
+ status = ath9k_hw_check_eeprom(ah);
+
+ return status;
+}
+
+u32 ath9k_hw_get_eeprom(struct ath_hal_5416 *ahp,
+ enum eeprom_param param)
+{
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ struct modal_eep_header *pModal = eep->modalHeader;
+ struct base_eep_header *pBase = &eep->baseEepHeader;
+
+ switch (param) {
+ case EEP_NFTHRESH_5:
+ return -pModal[0].noiseFloorThreshCh[0];
+ case EEP_NFTHRESH_2:
+ return -pModal[1].noiseFloorThreshCh[0];
+ case AR_EEPROM_MAC(0):
+ return pBase->macAddr[0] << 8 | pBase->macAddr[1];
+ case AR_EEPROM_MAC(1):
+ return pBase->macAddr[2] << 8 | pBase->macAddr[3];
+ case AR_EEPROM_MAC(2):
+ return pBase->macAddr[4] << 8 | pBase->macAddr[5];
+ case EEP_REG_0:
+ return pBase->regDmn[0];
+ case EEP_REG_1:
+ return pBase->regDmn[1];
+ case EEP_OP_CAP:
+ return pBase->deviceCap;
+ case EEP_OP_MODE:
+ return pBase->opCapFlags;
+ case EEP_RF_SILENT:
+ return pBase->rfSilent;
+ case EEP_OB_5:
+ return pModal[0].ob;
+ case EEP_DB_5:
+ return pModal[0].db;
+ case EEP_OB_2:
+ return pModal[1].ob;
+ case EEP_DB_2:
+ return pModal[1].db;
+ case EEP_MINOR_REV:
+ return pBase->version & AR5416_EEP_VER_MINOR_MASK;
+ case EEP_TX_MASK:
+ return pBase->txMask;
+ case EEP_RX_MASK:
+ return pBase->rxMask;
+ default:
+ return 0;
+ }
+}
+
+static inline int ath9k_hw_get_radiorev(struct ath_hal *ah)
+{
+ u32 val;
+ int i;
+
+ REG_WRITE(ah, AR_PHY(0x36), 0x00007058);
+ for (i = 0; i < 8; i++)
+ REG_WRITE(ah, AR_PHY(0x20), 0x00010000);
+ val = (REG_READ(ah, AR_PHY(256)) >> 24) & 0xff;
+ val = ((val & 0xf0) >> 4) | ((val & 0x0f) << 4);
+ return ath9k_hw_reverse_bits(val, 8);
+}
+
+static inline int ath9k_hw_init_macaddr(struct ath_hal *ah)
+{
+ u32 sum;
+ int i;
+ u16 eeval;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ DECLARE_MAC_BUF(mac);
+
+ sum = 0;
+ for (i = 0; i < 3; i++) {
+ eeval = ath9k_hw_get_eeprom(ahp, AR_EEPROM_MAC(i));
+ sum += eeval;
+ ahp->ah_macaddr[2 * i] = eeval >> 8;
+ ahp->ah_macaddr[2 * i + 1] = eeval & 0xff;
+ }
+ if (sum == 0 || sum == 0xffff * 3) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: mac address read failed: %s\n", __func__,
+ print_mac(mac, ahp->ah_macaddr));
+ return -EADDRNOTAVAIL;
+ }
+
+ return 0;
+}
+
+static inline int16_t ath9k_hw_interpolate(u16 target,
+ u16 srcLeft,
+ u16 srcRight,
+ int16_t targetLeft,
+ int16_t targetRight)
+{
+ int16_t rv;
+
+ if (srcRight == srcLeft) {
+ rv = targetLeft;
+ } else {
+ rv = (int16_t) (((target - srcLeft) * targetRight +
+ (srcRight - target) * targetLeft) /
+ (srcRight - srcLeft));
+ }
+ return rv;
+}
+
+static inline u16 ath9k_hw_fbin2freq(u8 fbin,
+ bool is2GHz)
+{
+
+ if (fbin == AR5416_BCHAN_UNUSED)
+ return fbin;
+
+ return (u16) ((is2GHz) ? (2300 + fbin) : (4800 + 5 * fbin));
+}
+
+static u16 ath9k_hw_eeprom_get_spur_chan(struct ath_hal *ah,
+ u16 i,
+ bool is2GHz)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416_eeprom *eep =
+ (struct ar5416_eeprom *) &ahp->ah_eeprom;
+ u16 spur_val = AR_NO_SPUR;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "Getting spur idx %d is2Ghz. %d val %x\n",
+ i, is2GHz, ah->ah_config.spurchans[i][is2GHz]);
+
+ switch (ah->ah_config.spurmode) {
+ case SPUR_DISABLE:
+ break;
+ case SPUR_ENABLE_IOCTL:
+ spur_val = ah->ah_config.spurchans[i][is2GHz];
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "Getting spur val from new loc. %d\n", spur_val);
+ break;
+ case SPUR_ENABLE_EEPROM:
+ spur_val = eep->modalHeader[is2GHz].spurChans[i].spurChan;
+ break;
+
+ }
+ return spur_val;
+}
+
+static inline int ath9k_hw_rfattach(struct ath_hal *ah)
+{
+ bool rfStatus = false;
+ int ecode = 0;
+
+ rfStatus = ath9k_hw_init_rf(ah, &ecode);
+ if (!rfStatus) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: RF setup failed, status %u\n", __func__,
+ ecode);
+ return ecode;
+ }
+
+ return 0;
+}
+
+static int ath9k_hw_rf_claim(struct ath_hal *ah)
+{
+ u32 val;
+
+ REG_WRITE(ah, AR_PHY(0), 0x00000007);
+
+ val = ath9k_hw_get_radiorev(ah);
+ switch (val & AR_RADIO_SREV_MAJOR) {
+ case 0:
+ val = AR_RAD5133_SREV_MAJOR;
+ break;
+ case AR_RAD5133_SREV_MAJOR:
+ case AR_RAD5122_SREV_MAJOR:
+ case AR_RAD2133_SREV_MAJOR:
+ case AR_RAD2122_SREV_MAJOR:
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: 5G Radio Chip Rev 0x%02X is not "
+ "supported by this driver\n",
+ __func__, ah->ah_analog5GhzRev);
+ return -EOPNOTSUPP;
+ }
+
+ ah->ah_analog5GhzRev = val;
+
+ return 0;
+}
+
+static inline void ath9k_hw_init_pll(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ u32 pll;
+
+ if (AR_SREV_9100(ah)) {
+ if (chan && IS_CHAN_5GHZ(chan))
+ pll = 0x1450;
+ else
+ pll = 0x1458;
+ } else {
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ pll = SM(0x5, AR_RTC_9160_PLL_REFDIV);
+
+ if (chan && IS_CHAN_HALF_RATE(chan))
+ pll |= SM(0x1, AR_RTC_9160_PLL_CLKSEL);
+ else if (chan && IS_CHAN_QUARTER_RATE(chan))
+ pll |= SM(0x2, AR_RTC_9160_PLL_CLKSEL);
+
+ if (chan && IS_CHAN_5GHZ(chan)) {
+ pll |= SM(0x28, AR_RTC_9160_PLL_DIV);
+
+
+ if (AR_SREV_9280_20(ah)) {
+ if (((chan->channel % 20) == 0)
+ || ((chan->channel % 10) == 0))
+ pll = 0x2850;
+ else
+ pll = 0x142c;
+ }
+ } else {
+ pll |= SM(0x2c, AR_RTC_9160_PLL_DIV);
+ }
+
+ } else if (AR_SREV_9160_10_OR_LATER(ah)) {
+
+ pll = SM(0x5, AR_RTC_9160_PLL_REFDIV);
+
+ if (chan && IS_CHAN_HALF_RATE(chan))
+ pll |= SM(0x1, AR_RTC_9160_PLL_CLKSEL);
+ else if (chan && IS_CHAN_QUARTER_RATE(chan))
+ pll |= SM(0x2, AR_RTC_9160_PLL_CLKSEL);
+
+ if (chan && IS_CHAN_5GHZ(chan))
+ pll |= SM(0x50, AR_RTC_9160_PLL_DIV);
+ else
+ pll |= SM(0x58, AR_RTC_9160_PLL_DIV);
+ } else {
+ pll = AR_RTC_PLL_REFDIV_5 | AR_RTC_PLL_DIV2;
+
+ if (chan && IS_CHAN_HALF_RATE(chan))
+ pll |= SM(0x1, AR_RTC_PLL_CLKSEL);
+ else if (chan && IS_CHAN_QUARTER_RATE(chan))
+ pll |= SM(0x2, AR_RTC_PLL_CLKSEL);
+
+ if (chan && IS_CHAN_5GHZ(chan))
+ pll |= SM(0xa, AR_RTC_PLL_DIV);
+ else
+ pll |= SM(0xb, AR_RTC_PLL_DIV);
+ }
+ }
+ REG_WRITE(ah, (u16) (AR_RTC_PLL_CONTROL), pll);
+
+ udelay(RTC_PLL_SETTLE_DELAY);
+
+ REG_WRITE(ah, AR_RTC_SLEEP_CLK, AR_RTC_FORCE_DERIVED_CLK);
+}
+
+static void ath9k_hw_set_regs(struct ath_hal *ah, struct ath9k_channel *chan,
+ enum ath9k_ht_macmode macmode)
+{
+ u32 phymode;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ phymode = AR_PHY_FC_HT_EN | AR_PHY_FC_SHORT_GI_40
+ | AR_PHY_FC_SINGLE_HT_LTF1 | AR_PHY_FC_WALSH;
+
+ if (IS_CHAN_HT40(chan)) {
+ phymode |= AR_PHY_FC_DYN2040_EN;
+
+ if ((chan->chanmode == CHANNEL_A_HT40PLUS) ||
+ (chan->chanmode == CHANNEL_G_HT40PLUS))
+ phymode |= AR_PHY_FC_DYN2040_PRI_CH;
+
+ if (ahp->ah_extprotspacing == ATH9K_HT_EXTPROTSPACING_25)
+ phymode |= AR_PHY_FC_DYN2040_EXT_CH;
+ }
+ REG_WRITE(ah, AR_PHY_TURBO, phymode);
+
+ ath9k_hw_set11nmac2040(ah, macmode);
+
+ REG_WRITE(ah, AR_GTXTO, 25 << AR_GTXTO_TIMEOUT_LIMIT_S);
+ REG_WRITE(ah, AR_CST, 0xF << AR_CST_TIMEOUT_LIMIT_S);
+}
+
+static void ath9k_hw_set_operating_mode(struct ath_hal *ah, int opmode)
+{
+ u32 val;
+
+ val = REG_READ(ah, AR_STA_ID1);
+ val &= ~(AR_STA_ID1_STA_AP | AR_STA_ID1_ADHOC);
+ switch (opmode) {
+ case ATH9K_M_HOSTAP:
+ REG_WRITE(ah, AR_STA_ID1, val | AR_STA_ID1_STA_AP
+ | AR_STA_ID1_KSRCH_MODE);
+ REG_CLR_BIT(ah, AR_CFG, AR_CFG_AP_ADHOC_INDICATION);
+ break;
+ case ATH9K_M_IBSS:
+ REG_WRITE(ah, AR_STA_ID1, val | AR_STA_ID1_ADHOC
+ | AR_STA_ID1_KSRCH_MODE);
+ REG_SET_BIT(ah, AR_CFG, AR_CFG_AP_ADHOC_INDICATION);
+ break;
+ case ATH9K_M_STA:
+ case ATH9K_M_MONITOR:
+ REG_WRITE(ah, AR_STA_ID1, val | AR_STA_ID1_KSRCH_MODE);
+ break;
+ }
+}
+
+static inline void
+ath9k_hw_set_rfmode(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ u32 rfMode = 0;
+
+ if (chan == NULL)
+ return;
+
+ rfMode |= (IS_CHAN_B(chan) || IS_CHAN_G(chan))
+ ? AR_PHY_MODE_DYNAMIC : AR_PHY_MODE_OFDM;
+
+ if (!AR_SREV_9280_10_OR_LATER(ah))
+ rfMode |= (IS_CHAN_5GHZ(chan)) ? AR_PHY_MODE_RF5GHZ :
+ AR_PHY_MODE_RF2GHZ;
+
+ if (AR_SREV_9280_20(ah) && IS_CHAN_A_5MHZ_SPACED(chan))
+ rfMode |= (AR_PHY_MODE_DYNAMIC | AR_PHY_MODE_DYN_CCK_DISABLE);
+
+ REG_WRITE(ah, AR_PHY_MODE, rfMode);
+}
+
+static bool ath9k_hw_set_reset(struct ath_hal *ah, int type)
+{
+ u32 rst_flags;
+ u32 tmpReg;
+
+ REG_WRITE(ah, AR_RTC_FORCE_WAKE, AR_RTC_FORCE_WAKE_EN |
+ AR_RTC_FORCE_WAKE_ON_INT);
+
+ if (AR_SREV_9100(ah)) {
+ rst_flags = AR_RTC_RC_MAC_WARM | AR_RTC_RC_MAC_COLD |
+ AR_RTC_RC_COLD_RESET | AR_RTC_RC_WARM_RESET;
+ } else {
+ tmpReg = REG_READ(ah, AR_INTR_SYNC_CAUSE);
+ if (tmpReg &
+ (AR_INTR_SYNC_LOCAL_TIMEOUT |
+ AR_INTR_SYNC_RADM_CPL_TIMEOUT)) {
+ REG_WRITE(ah, AR_INTR_SYNC_ENABLE, 0);
+ REG_WRITE(ah, AR_RC, AR_RC_AHB | AR_RC_HOSTIF);
+ } else {
+ REG_WRITE(ah, AR_RC, AR_RC_AHB);
+ }
+
+ rst_flags = AR_RTC_RC_MAC_WARM;
+ if (type == ATH9K_RESET_COLD)
+ rst_flags |= AR_RTC_RC_MAC_COLD;
+ }
+
+ REG_WRITE(ah, (u16) (AR_RTC_RC), rst_flags);
+ udelay(50);
+
+ REG_WRITE(ah, (u16) (AR_RTC_RC), 0);
+ if (!ath9k_hw_wait(ah, (u16) (AR_RTC_RC), AR_RTC_RC_M, 0)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: RTC stuck in MAC reset\n",
+ __func__);
+ return false;
+ }
+
+ if (!AR_SREV_9100(ah))
+ REG_WRITE(ah, AR_RC, 0);
+
+ ath9k_hw_init_pll(ah, NULL);
+
+ if (AR_SREV_9100(ah))
+ udelay(50);
+
+ return true;
+}
+
+static inline bool ath9k_hw_set_reset_power_on(struct ath_hal *ah)
+{
+ REG_WRITE(ah, AR_RTC_FORCE_WAKE, AR_RTC_FORCE_WAKE_EN |
+ AR_RTC_FORCE_WAKE_ON_INT);
+
+ REG_WRITE(ah, (u16) (AR_RTC_RESET), 0);
+ REG_WRITE(ah, (u16) (AR_RTC_RESET), 1);
+
+ if (!ath9k_hw_wait(ah,
+ AR_RTC_STATUS,
+ AR_RTC_STATUS_M,
+ AR_RTC_STATUS_ON)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: RTC not waking up\n",
+ __func__);
+ return false;
+ }
+
+ ath9k_hw_read_revisions(ah);
+
+ return ath9k_hw_set_reset(ah, ATH9K_RESET_WARM);
+}
+
+static bool ath9k_hw_set_reset_reg(struct ath_hal *ah,
+ u32 type)
+{
+ REG_WRITE(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_EN | AR_RTC_FORCE_WAKE_ON_INT);
+
+ switch (type) {
+ case ATH9K_RESET_POWER_ON:
+ return ath9k_hw_set_reset_power_on(ah);
+ break;
+ case ATH9K_RESET_WARM:
+ case ATH9K_RESET_COLD:
+ return ath9k_hw_set_reset(ah, type);
+ break;
+ default:
+ return false;
+ }
+}
+
+static inline
+struct ath9k_channel *ath9k_hw_check_chan(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ if (!(IS_CHAN_2GHZ(chan) ^ IS_CHAN_5GHZ(chan))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u/0x%x; not marked as "
+ "2GHz or 5GHz\n", __func__, chan->channel,
+ chan->channelFlags);
+ return NULL;
+ }
+
+ if (!IS_CHAN_OFDM(chan) &&
+ !IS_CHAN_CCK(chan) &&
+ !IS_CHAN_HT20(chan) &&
+ !IS_CHAN_HT40(chan)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u/0x%x; not marked as "
+ "OFDM or CCK or HT20 or HT40PLUS or HT40MINUS\n",
+ __func__, chan->channel, chan->channelFlags);
+ return NULL;
+ }
+
+ return ath9k_regd_check_channel(ah, chan);
+}
+
+static inline bool
+ath9k_hw_get_lower_upper_index(u8 target,
+ u8 *pList,
+ u16 listSize,
+ u16 *indexL,
+ u16 *indexR)
+{
+ u16 i;
+
+ if (target <= pList[0]) {
+ *indexL = *indexR = 0;
+ return true;
+ }
+ if (target >= pList[listSize - 1]) {
+ *indexL = *indexR = (u16) (listSize - 1);
+ return true;
+ }
+
+ for (i = 0; i < listSize - 1; i++) {
+ if (pList[i] == target) {
+ *indexL = *indexR = i;
+ return true;
+ }
+ if (target < pList[i + 1]) {
+ *indexL = i;
+ *indexR = (u16) (i + 1);
+ return false;
+ }
+ }
+ return false;
+}
+
+static int16_t ath9k_hw_get_nf_hist_mid(int16_t *nfCalBuffer)
+{
+ int16_t nfval;
+ int16_t sort[ATH9K_NF_CAL_HIST_MAX];
+ int i, j;
+
+ for (i = 0; i < ATH9K_NF_CAL_HIST_MAX; i++)
+ sort[i] = nfCalBuffer[i];
+
+ for (i = 0; i < ATH9K_NF_CAL_HIST_MAX - 1; i++) {
+ for (j = 1; j < ATH9K_NF_CAL_HIST_MAX - i; j++) {
+ if (sort[j] > sort[j - 1]) {
+ nfval = sort[j];
+ sort[j] = sort[j - 1];
+ sort[j - 1] = nfval;
+ }
+ }
+ }
+ nfval = sort[(ATH9K_NF_CAL_HIST_MAX - 1) >> 1];
+
+ return nfval;
+}
+
+static void ath9k_hw_update_nfcal_hist_buffer(struct ath9k_nfcal_hist *h,
+ int16_t *nfarray)
+{
+ int i;
+
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ h[i].nfCalBuffer[h[i].currIndex] = nfarray[i];
+
+ if (++h[i].currIndex >= ATH9K_NF_CAL_HIST_MAX)
+ h[i].currIndex = 0;
+
+ if (h[i].invalidNFcount > 0) {
+ if (nfarray[i] < AR_PHY_CCA_MIN_BAD_VALUE
+ || nfarray[i] > AR_PHY_CCA_MAX_HIGH_VALUE) {
+ h[i].invalidNFcount = ATH9K_NF_CAL_HIST_MAX;
+ } else {
+ h[i].invalidNFcount--;
+ h[i].privNF = nfarray[i];
+ }
+ } else {
+ h[i].privNF =
+ ath9k_hw_get_nf_hist_mid(h[i].nfCalBuffer);
+ }
+ }
+ return;
+}
+
+static void ar5416GetNoiseFloor(struct ath_hal *ah,
+ int16_t nfarray[NUM_NF_READINGS])
+{
+ int16_t nf;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ nf = MS(REG_READ(ah, AR_PHY_CCA), AR9280_PHY_MINCCA_PWR);
+ else
+ nf = MS(REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR);
+
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "NF calibrated [ctl] [chain 0] is %d\n", nf);
+ nfarray[0] = nf;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ nf = MS(REG_READ(ah, AR_PHY_CH1_CCA),
+ AR9280_PHY_CH1_MINCCA_PWR);
+ else
+ nf = MS(REG_READ(ah, AR_PHY_CH1_CCA),
+ AR_PHY_CH1_MINCCA_PWR);
+
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_NF_CAL,
+ "NF calibrated [ctl] [chain 1] is %d\n", nf);
+ nfarray[1] = nf;
+
+ if (!AR_SREV_9280(ah)) {
+ nf = MS(REG_READ(ah, AR_PHY_CH2_CCA),
+ AR_PHY_CH2_MINCCA_PWR);
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_NF_CAL,
+ "NF calibrated [ctl] [chain 2] is %d\n", nf);
+ nfarray[2] = nf;
+ }
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ nf = MS(REG_READ(ah, AR_PHY_EXT_CCA),
+ AR9280_PHY_EXT_MINCCA_PWR);
+ else
+ nf = MS(REG_READ(ah, AR_PHY_EXT_CCA),
+ AR_PHY_EXT_MINCCA_PWR);
+
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_NF_CAL,
+ "NF calibrated [ext] [chain 0] is %d\n", nf);
+ nfarray[3] = nf;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ nf = MS(REG_READ(ah, AR_PHY_CH1_EXT_CCA),
+ AR9280_PHY_CH1_EXT_MINCCA_PWR);
+ else
+ nf = MS(REG_READ(ah, AR_PHY_CH1_EXT_CCA),
+ AR_PHY_CH1_EXT_MINCCA_PWR);
+
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "NF calibrated [ext] [chain 1] is %d\n", nf);
+ nfarray[4] = nf;
+
+ if (!AR_SREV_9280(ah)) {
+ nf = MS(REG_READ(ah, AR_PHY_CH2_EXT_CCA),
+ AR_PHY_CH2_EXT_MINCCA_PWR);
+ if (nf & 0x100)
+ nf = 0 - ((nf ^ 0x1ff) + 1);
+ DPRINTF(ah->ah_sc, ATH_DBG_NF_CAL,
+ "NF calibrated [ext] [chain 2] is %d\n", nf);
+ nfarray[5] = nf;
+ }
+}
+
+static bool
+getNoiseFloorThresh(struct ath_hal *ah,
+ const struct ath9k_channel *chan,
+ int16_t *nft)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ switch (chan->chanmode) {
+ case CHANNEL_A:
+ case CHANNEL_A_HT20:
+ case CHANNEL_A_HT40PLUS:
+ case CHANNEL_A_HT40MINUS:
+ *nft = (int16_t) ath9k_hw_get_eeprom(ahp, EEP_NFTHRESH_5);
+ break;
+ case CHANNEL_B:
+ case CHANNEL_G:
+ case CHANNEL_G_HT20:
+ case CHANNEL_G_HT40PLUS:
+ case CHANNEL_G_HT40MINUS:
+ *nft = (int16_t) ath9k_hw_get_eeprom(ahp, EEP_NFTHRESH_2);
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel flags 0x%x\n", __func__,
+ chan->channelFlags);
+ return false;
+ }
+ return true;
+}
+
+static void ath9k_hw_start_nfcal(struct ath_hal *ah)
+{
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_ENABLE_NF);
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
+}
+
+static void
+ath9k_hw_loadnf(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ struct ath9k_nfcal_hist *h;
+ int i, j;
+ int32_t val;
+ const u32 ar5416_cca_regs[6] = {
+ AR_PHY_CCA,
+ AR_PHY_CH1_CCA,
+ AR_PHY_CH2_CCA,
+ AR_PHY_EXT_CCA,
+ AR_PHY_CH1_EXT_CCA,
+ AR_PHY_CH2_EXT_CCA
+ };
+ u8 chainmask;
+
+ if (AR_SREV_9280(ah))
+ chainmask = 0x1B;
+ else
+ chainmask = 0x3F;
+
+#ifdef ATH_NF_PER_CHAN
+ h = chan->nfCalHist;
+#else
+ h = ah->nfCalHist;
+#endif
+
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ if (chainmask & (1 << i)) {
+ val = REG_READ(ah, ar5416_cca_regs[i]);
+ val &= 0xFFFFFE00;
+ val |= (((u32) (h[i].privNF) << 1) & 0x1ff);
+ REG_WRITE(ah, ar5416_cca_regs[i], val);
+ }
+ }
+
+ REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_ENABLE_NF);
+ REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL,
+ AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
+
+ for (j = 0; j < 1000; j++) {
+ if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
+ AR_PHY_AGC_CONTROL_NF) == 0)
+ break;
+ udelay(10);
+ }
+
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ if (chainmask & (1 << i)) {
+ val = REG_READ(ah, ar5416_cca_regs[i]);
+ val &= 0xFFFFFE00;
+ val |= (((u32) (-50) << 1) & 0x1ff);
+ REG_WRITE(ah, ar5416_cca_regs[i], val);
+ }
+ }
+}
+
+static int16_t ath9k_hw_getnf(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ int16_t nf, nfThresh;
+ int16_t nfarray[NUM_NF_READINGS] = { 0 };
+ struct ath9k_nfcal_hist *h;
+ u8 chainmask;
+
+ if (AR_SREV_9280(ah))
+ chainmask = 0x1B;
+ else
+ chainmask = 0x3F;
+
+ chan->channelFlags &= (~CHANNEL_CW_INT);
+ if (REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: NF did not complete in calibration window\n",
+ __func__);
+ nf = 0;
+ chan->rawNoiseFloor = nf;
+ return chan->rawNoiseFloor;
+ } else {
+ ar5416GetNoiseFloor(ah, nfarray);
+ nf = nfarray[0];
+ if (getNoiseFloorThresh(ah, chan, &nfThresh)
+ && nf > nfThresh) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: noise floor failed detected; "
+ "detected %d, threshold %d\n", __func__,
+ nf, nfThresh);
+ chan->channelFlags |= CHANNEL_CW_INT;
+ }
+ }
+
+#ifdef ATH_NF_PER_CHAN
+ h = chan->nfCalHist;
+#else
+ h = ah->nfCalHist;
+#endif
+
+ ath9k_hw_update_nfcal_hist_buffer(h, nfarray);
+ chan->rawNoiseFloor = h[0].privNF;
+
+ return chan->rawNoiseFloor;
+}
+
+static void ath9k_hw_update_mibstats(struct ath_hal *ah,
+ struct ath9k_mib_stats *stats)
+{
+ stats->ackrcv_bad += REG_READ(ah, AR_ACK_FAIL);
+ stats->rts_bad += REG_READ(ah, AR_RTS_FAIL);
+ stats->fcs_bad += REG_READ(ah, AR_FCS_FAIL);
+ stats->rts_good += REG_READ(ah, AR_RTS_OK);
+ stats->beacons += REG_READ(ah, AR_BEACON_CNT);
+}
+
+static void ath9k_enable_mib_counters(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "Enable mib counters\n");
+
+ ath9k_hw_update_mibstats(ah, &ahp->ah_mibStats);
+
+ REG_WRITE(ah, AR_FILT_OFDM, 0);
+ REG_WRITE(ah, AR_FILT_CCK, 0);
+ REG_WRITE(ah, AR_MIBC,
+ ~(AR_MIBC_COW | AR_MIBC_FMC | AR_MIBC_CMC | AR_MIBC_MCS)
+ & 0x0f);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_1, AR_PHY_ERR_OFDM_TIMING);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_2, AR_PHY_ERR_CCK_TIMING);
+}
+
+static void ath9k_hw_disable_mib_counters(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "Disabling MIB counters\n");
+
+ REG_WRITE(ah, AR_MIBC, AR_MIBC_FMC | AR_MIBC_CMC);
+
+ ath9k_hw_update_mibstats(ah, &ahp->ah_mibStats);
+
+ REG_WRITE(ah, AR_FILT_OFDM, 0);
+ REG_WRITE(ah, AR_FILT_CCK, 0);
+}
+
+static int ath9k_hw_get_ani_channel_idx(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ahp->ah_ani); i++) {
+ if (ahp->ah_ani[i].c.channel == chan->channel)
+ return i;
+ if (ahp->ah_ani[i].c.channel == 0) {
+ ahp->ah_ani[i].c.channel = chan->channel;
+ ahp->ah_ani[i].c.channelFlags = chan->channelFlags;
+ return i;
+ }
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "No more channel states left. Using channel 0\n");
+ return 0;
+}
+
+static void ath9k_hw_ani_attach(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ ahp->ah_hasHwPhyCounters = 1;
+
+ memset(ahp->ah_ani, 0, sizeof(ahp->ah_ani));
+ for (i = 0; i < ARRAY_SIZE(ahp->ah_ani); i++) {
+ ahp->ah_ani[i].ofdmTrigHigh = ATH9K_ANI_OFDM_TRIG_HIGH;
+ ahp->ah_ani[i].ofdmTrigLow = ATH9K_ANI_OFDM_TRIG_LOW;
+ ahp->ah_ani[i].cckTrigHigh = ATH9K_ANI_CCK_TRIG_HIGH;
+ ahp->ah_ani[i].cckTrigLow = ATH9K_ANI_CCK_TRIG_LOW;
+ ahp->ah_ani[i].rssiThrHigh = ATH9K_ANI_RSSI_THR_HIGH;
+ ahp->ah_ani[i].rssiThrLow = ATH9K_ANI_RSSI_THR_LOW;
+ ahp->ah_ani[i].ofdmWeakSigDetectOff =
+ !ATH9K_ANI_USE_OFDM_WEAK_SIG;
+ ahp->ah_ani[i].cckWeakSigThreshold =
+ ATH9K_ANI_CCK_WEAK_SIG_THR;
+ ahp->ah_ani[i].spurImmunityLevel = ATH9K_ANI_SPUR_IMMUNE_LVL;
+ ahp->ah_ani[i].firstepLevel = ATH9K_ANI_FIRSTEP_LVL;
+ if (ahp->ah_hasHwPhyCounters) {
+ ahp->ah_ani[i].ofdmPhyErrBase =
+ AR_PHY_COUNTMAX - ATH9K_ANI_OFDM_TRIG_HIGH;
+ ahp->ah_ani[i].cckPhyErrBase =
+ AR_PHY_COUNTMAX - ATH9K_ANI_CCK_TRIG_HIGH;
+ }
+ }
+ if (ahp->ah_hasHwPhyCounters) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "Setting OfdmErrBase = 0x%08x\n",
+ ahp->ah_ani[0].ofdmPhyErrBase);
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "Setting cckErrBase = 0x%08x\n",
+ ahp->ah_ani[0].cckPhyErrBase);
+
+ REG_WRITE(ah, AR_PHY_ERR_1, ahp->ah_ani[0].ofdmPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_2, ahp->ah_ani[0].cckPhyErrBase);
+ ath9k_enable_mib_counters(ah);
+ }
+ ahp->ah_aniPeriod = ATH9K_ANI_PERIOD;
+ if (ah->ah_config.enable_ani)
+ ahp->ah_procPhyErr |= HAL_PROCESS_ANI;
+}
+
+static inline void ath9k_hw_ani_setup(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ const int totalSizeDesired[] = { -55, -55, -55, -55, -62 };
+ const int coarseHigh[] = { -14, -14, -14, -14, -12 };
+ const int coarseLow[] = { -64, -64, -64, -64, -70 };
+ const int firpwr[] = { -78, -78, -78, -78, -80 };
+
+ for (i = 0; i < 5; i++) {
+ ahp->ah_totalSizeDesired[i] = totalSizeDesired[i];
+ ahp->ah_coarseHigh[i] = coarseHigh[i];
+ ahp->ah_coarseLow[i] = coarseLow[i];
+ ahp->ah_firpwr[i] = firpwr[i];
+ }
+}
+
+static void ath9k_hw_ani_detach(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "Detaching Ani\n");
+ if (ahp->ah_hasHwPhyCounters) {
+ ath9k_hw_disable_mib_counters(ah);
+ REG_WRITE(ah, AR_PHY_ERR_1, 0);
+ REG_WRITE(ah, AR_PHY_ERR_2, 0);
+ }
+}
+
+
+static bool ath9k_hw_ani_control(struct ath_hal *ah,
+ enum ath9k_ani_cmd cmd, int param)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState = ahp->ah_curani;
+
+ switch (cmd & ahp->ah_ani_function) {
+ case ATH9K_ANI_NOISE_IMMUNITY_LEVEL:{
+ u32 level = param;
+
+ if (level >= ARRAY_SIZE(ahp->ah_totalSizeDesired)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: level out of range (%u > %u)\n",
+ __func__, level,
+ (unsigned) ARRAY_SIZE(ahp->
+ ah_totalSizeDesired));
+ return false;
+ }
+
+ REG_RMW_FIELD(ah, AR_PHY_DESIRED_SZ,
+ AR_PHY_DESIRED_SZ_TOT_DES,
+ ahp->ah_totalSizeDesired[level]);
+ REG_RMW_FIELD(ah, AR_PHY_AGC_CTL1,
+ AR_PHY_AGC_CTL1_COARSE_LOW,
+ ahp->ah_coarseLow[level]);
+ REG_RMW_FIELD(ah, AR_PHY_AGC_CTL1,
+ AR_PHY_AGC_CTL1_COARSE_HIGH,
+ ahp->ah_coarseHigh[level]);
+ REG_RMW_FIELD(ah, AR_PHY_FIND_SIG,
+ AR_PHY_FIND_SIG_FIRPWR,
+ ahp->ah_firpwr[level]);
+
+ if (level > aniState->noiseImmunityLevel)
+ ahp->ah_stats.ast_ani_niup++;
+ else if (level < aniState->noiseImmunityLevel)
+ ahp->ah_stats.ast_ani_nidown++;
+ aniState->noiseImmunityLevel = level;
+ break;
+ }
+ case ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION:{
+ const int m1ThreshLow[] = { 127, 50 };
+ const int m2ThreshLow[] = { 127, 40 };
+ const int m1Thresh[] = { 127, 0x4d };
+ const int m2Thresh[] = { 127, 0x40 };
+ const int m2CountThr[] = { 31, 16 };
+ const int m2CountThrLow[] = { 63, 48 };
+ u32 on = param ? 1 : 0;
+
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M1_THRESH_LOW,
+ m1ThreshLow[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M2_THRESH_LOW,
+ m2ThreshLow[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M1_THRESH,
+ m1Thresh[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M2_THRESH,
+ m2Thresh[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR,
+ AR_PHY_SFCORR_M2COUNT_THR,
+ m2CountThr[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_M2COUNT_THR_LOW,
+ m2CountThrLow[on]);
+
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M1_THRESH_LOW,
+ m1ThreshLow[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M2_THRESH_LOW,
+ m2ThreshLow[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M1_THRESH,
+ m1Thresh[on]);
+ REG_RMW_FIELD(ah, AR_PHY_SFCORR_EXT,
+ AR_PHY_SFCORR_EXT_M2_THRESH,
+ m2Thresh[on]);
+
+ if (on)
+ REG_SET_BIT(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_USE_SELF_CORR_LOW);
+ else
+ REG_CLR_BIT(ah, AR_PHY_SFCORR_LOW,
+ AR_PHY_SFCORR_LOW_USE_SELF_CORR_LOW);
+
+ if (!on != aniState->ofdmWeakSigDetectOff) {
+ if (on)
+ ahp->ah_stats.ast_ani_ofdmon++;
+ else
+ ahp->ah_stats.ast_ani_ofdmoff++;
+ aniState->ofdmWeakSigDetectOff = !on;
+ }
+ break;
+ }
+ case ATH9K_ANI_CCK_WEAK_SIGNAL_THR:{
+ const int weakSigThrCck[] = { 8, 6 };
+ u32 high = param ? 1 : 0;
+
+ REG_RMW_FIELD(ah, AR_PHY_CCK_DETECT,
+ AR_PHY_CCK_DETECT_WEAK_SIG_THR_CCK,
+ weakSigThrCck[high]);
+ if (high != aniState->cckWeakSigThreshold) {
+ if (high)
+ ahp->ah_stats.ast_ani_cckhigh++;
+ else
+ ahp->ah_stats.ast_ani_ccklow++;
+ aniState->cckWeakSigThreshold = high;
+ }
+ break;
+ }
+ case ATH9K_ANI_FIRSTEP_LEVEL:{
+ const int firstep[] = { 0, 4, 8 };
+ u32 level = param;
+
+ if (level >= ARRAY_SIZE(firstep)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: level out of range (%u > %u)\n",
+ __func__, level,
+ (unsigned) ARRAY_SIZE(firstep));
+ return false;
+ }
+ REG_RMW_FIELD(ah, AR_PHY_FIND_SIG,
+ AR_PHY_FIND_SIG_FIRSTEP,
+ firstep[level]);
+ if (level > aniState->firstepLevel)
+ ahp->ah_stats.ast_ani_stepup++;
+ else if (level < aniState->firstepLevel)
+ ahp->ah_stats.ast_ani_stepdown++;
+ aniState->firstepLevel = level;
+ break;
+ }
+ case ATH9K_ANI_SPUR_IMMUNITY_LEVEL:{
+ const int cycpwrThr1[] =
+ { 2, 4, 6, 8, 10, 12, 14, 16 };
+ u32 level = param;
+
+ if (level >= ARRAY_SIZE(cycpwrThr1)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: level out of range (%u > %u)\n",
+ __func__, level,
+ (unsigned)
+ ARRAY_SIZE(cycpwrThr1));
+ return false;
+ }
+ REG_RMW_FIELD(ah, AR_PHY_TIMING5,
+ AR_PHY_TIMING5_CYCPWR_THR1,
+ cycpwrThr1[level]);
+ if (level > aniState->spurImmunityLevel)
+ ahp->ah_stats.ast_ani_spurup++;
+ else if (level < aniState->spurImmunityLevel)
+ ahp->ah_stats.ast_ani_spurdown++;
+ aniState->spurImmunityLevel = level;
+ break;
+ }
+ case ATH9K_ANI_PRESENT:
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: invalid cmd %u\n", __func__, cmd);
+ return false;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "%s: ANI parameters:\n", __func__);
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "noiseImmunityLevel=%d, spurImmunityLevel=%d, "
+ "ofdmWeakSigDetectOff=%d\n",
+ aniState->noiseImmunityLevel, aniState->spurImmunityLevel,
+ !aniState->ofdmWeakSigDetectOff);
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "cckWeakSigThreshold=%d, "
+ "firstepLevel=%d, listenTime=%d\n",
+ aniState->cckWeakSigThreshold, aniState->firstepLevel,
+ aniState->listenTime);
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "cycleCount=%d, ofdmPhyErrCount=%d, cckPhyErrCount=%d\n\n",
+ aniState->cycleCount, aniState->ofdmPhyErrCount,
+ aniState->cckPhyErrCount);
+ return true;
+}
+
+static void ath9k_ani_restart(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState;
+
+ if (!DO_ANI(ah))
+ return;
+
+ aniState = ahp->ah_curani;
+
+ aniState->listenTime = 0;
+ if (ahp->ah_hasHwPhyCounters) {
+ if (aniState->ofdmTrigHigh > AR_PHY_COUNTMAX) {
+ aniState->ofdmPhyErrBase = 0;
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "OFDM Trigger is too high for hw counters\n");
+ } else {
+ aniState->ofdmPhyErrBase =
+ AR_PHY_COUNTMAX - aniState->ofdmTrigHigh;
+ }
+ if (aniState->cckTrigHigh > AR_PHY_COUNTMAX) {
+ aniState->cckPhyErrBase = 0;
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "CCK Trigger is too high for hw counters\n");
+ } else {
+ aniState->cckPhyErrBase =
+ AR_PHY_COUNTMAX - aniState->cckTrigHigh;
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: Writing ofdmbase=%u cckbase=%u\n",
+ __func__, aniState->ofdmPhyErrBase,
+ aniState->cckPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_1, aniState->ofdmPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_2, aniState->cckPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_1, AR_PHY_ERR_OFDM_TIMING);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_2, AR_PHY_ERR_CCK_TIMING);
+
+ ath9k_hw_update_mibstats(ah, &ahp->ah_mibStats);
+ }
+ aniState->ofdmPhyErrCount = 0;
+ aniState->cckPhyErrCount = 0;
+}
+
+static void ath9k_hw_ani_ofdm_err_trigger(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *chan = ah->ah_curchan;
+ struct ar5416AniState *aniState;
+ enum wireless_mode mode;
+ int32_t rssi;
+
+ if (!DO_ANI(ah))
+ return;
+
+ aniState = ahp->ah_curani;
+
+ if (aniState->noiseImmunityLevel < HAL_NOISE_IMMUNE_MAX) {
+ if (ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL,
+ aniState->noiseImmunityLevel + 1)) {
+ return;
+ }
+ }
+
+ if (aniState->spurImmunityLevel < HAL_SPUR_IMMUNE_MAX) {
+ if (ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL,
+ aniState->spurImmunityLevel + 1)) {
+ return;
+ }
+ }
+
+ if (ah->ah_opmode == ATH9K_M_HOSTAP) {
+ if (aniState->firstepLevel < HAL_FIRST_STEP_MAX) {
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel + 1);
+ }
+ return;
+ }
+ rssi = BEACON_RSSI(ahp);
+ if (rssi > aniState->rssiThrHigh) {
+ if (!aniState->ofdmWeakSigDetectOff) {
+ if (ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ false)) {
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_SPUR_IMMUNITY_LEVEL,
+ 0);
+ return;
+ }
+ }
+ if (aniState->firstepLevel < HAL_FIRST_STEP_MAX) {
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel + 1);
+ return;
+ }
+ } else if (rssi > aniState->rssiThrLow) {
+ if (aniState->ofdmWeakSigDetectOff)
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ true);
+ if (aniState->firstepLevel < HAL_FIRST_STEP_MAX)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel + 1);
+ return;
+ } else {
+ mode = ath9k_hw_chan2wmode(ah, chan);
+ if (mode == ATH9K_MODE_11G || mode == ATH9K_MODE_11B) {
+ if (!aniState->ofdmWeakSigDetectOff)
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ false);
+ if (aniState->firstepLevel > 0)
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_FIRSTEP_LEVEL,
+ 0);
+ return;
+ }
+ }
+}
+
+static void ath9k_hw_ani_cck_err_trigger(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *chan = ah->ah_curchan;
+ struct ar5416AniState *aniState;
+ enum wireless_mode mode;
+ int32_t rssi;
+
+ if (!DO_ANI(ah))
+ return;
+
+ aniState = ahp->ah_curani;
+ if (aniState->noiseImmunityLevel < HAL_NOISE_IMMUNE_MAX) {
+ if (ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL,
+ aniState->noiseImmunityLevel + 1)) {
+ return;
+ }
+ }
+ if (ah->ah_opmode == ATH9K_M_HOSTAP) {
+ if (aniState->firstepLevel < HAL_FIRST_STEP_MAX) {
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel + 1);
+ }
+ return;
+ }
+ rssi = BEACON_RSSI(ahp);
+ if (rssi > aniState->rssiThrLow) {
+ if (aniState->firstepLevel < HAL_FIRST_STEP_MAX)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel + 1);
+ } else {
+ mode = ath9k_hw_chan2wmode(ah, chan);
+ if (mode == ATH9K_MODE_11G || mode == ATH9K_MODE_11B) {
+ if (aniState->firstepLevel > 0)
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_FIRSTEP_LEVEL,
+ 0);
+ }
+ }
+}
+
+static void ath9k_ani_reset(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState;
+ struct ath9k_channel *chan = ah->ah_curchan;
+ int index;
+
+ if (!DO_ANI(ah))
+ return;
+
+ index = ath9k_hw_get_ani_channel_idx(ah, chan);
+ aniState = &ahp->ah_ani[index];
+ ahp->ah_curani = aniState;
+
+ if (DO_ANI(ah) && ah->ah_opmode != ATH9K_M_STA
+ && ah->ah_opmode != ATH9K_M_IBSS) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: Reset ANI state opmode %u\n", __func__,
+ ah->ah_opmode);
+ ahp->ah_stats.ast_ani_reset++;
+ ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL, 0);
+ ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL, 0);
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, 0);
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ !ATH9K_ANI_USE_OFDM_WEAK_SIG);
+ ath9k_hw_ani_control(ah, ATH9K_ANI_CCK_WEAK_SIGNAL_THR,
+ ATH9K_ANI_CCK_WEAK_SIG_THR);
+ ath9k_hw_setrxfilter(ah,
+ ath9k_hw_getrxfilter(ah) |
+ ATH9K_RX_FILTER_PHYERR);
+ if (ah->ah_opmode == ATH9K_M_HOSTAP) {
+ ahp->ah_curani->ofdmTrigHigh =
+ ah->ah_config.ofdm_trig_high;
+ ahp->ah_curani->ofdmTrigLow =
+ ah->ah_config.ofdm_trig_low;
+ ahp->ah_curani->cckTrigHigh =
+ ah->ah_config.cck_trig_high;
+ ahp->ah_curani->cckTrigLow =
+ ah->ah_config.cck_trig_low;
+ }
+ ath9k_ani_restart(ah);
+ return;
+ }
+
+ if (aniState->noiseImmunityLevel != 0)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL,
+ aniState->noiseImmunityLevel);
+ if (aniState->spurImmunityLevel != 0)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL,
+ aniState->spurImmunityLevel);
+ if (aniState->ofdmWeakSigDetectOff)
+ ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ !aniState->ofdmWeakSigDetectOff);
+ if (aniState->cckWeakSigThreshold)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_CCK_WEAK_SIGNAL_THR,
+ aniState->cckWeakSigThreshold);
+ if (aniState->firstepLevel != 0)
+ ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel);
+ if (ahp->ah_hasHwPhyCounters) {
+ ath9k_hw_setrxfilter(ah,
+ ath9k_hw_getrxfilter(ah) &
+ ~ATH9K_RX_FILTER_PHYERR);
+ ath9k_ani_restart(ah);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_1, AR_PHY_ERR_OFDM_TIMING);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_2, AR_PHY_ERR_CCK_TIMING);
+
+ } else {
+ ath9k_ani_restart(ah);
+ ath9k_hw_setrxfilter(ah,
+ ath9k_hw_getrxfilter(ah) |
+ ATH9K_RX_FILTER_PHYERR);
+ }
+}
+
+void ath9k_hw_procmibevent(struct ath_hal *ah,
+ const struct ath9k_node_stats *stats)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 phyCnt1, phyCnt2;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI, "Processing Mib Intr\n");
+
+ REG_WRITE(ah, AR_FILT_OFDM, 0);
+ REG_WRITE(ah, AR_FILT_CCK, 0);
+ if (!(REG_READ(ah, AR_SLP_MIB_CTRL) & AR_SLP_MIB_PENDING))
+ REG_WRITE(ah, AR_SLP_MIB_CTRL, AR_SLP_MIB_CLEAR);
+
+ ath9k_hw_update_mibstats(ah, &ahp->ah_mibStats);
+ ahp->ah_stats.ast_nodestats = *stats;
+
+ if (!DO_ANI(ah))
+ return;
+
+ phyCnt1 = REG_READ(ah, AR_PHY_ERR_1);
+ phyCnt2 = REG_READ(ah, AR_PHY_ERR_2);
+ if (((phyCnt1 & AR_MIBCNT_INTRMASK) == AR_MIBCNT_INTRMASK) ||
+ ((phyCnt2 & AR_MIBCNT_INTRMASK) == AR_MIBCNT_INTRMASK)) {
+ struct ar5416AniState *aniState = ahp->ah_curani;
+ u32 ofdmPhyErrCnt, cckPhyErrCnt;
+
+ ofdmPhyErrCnt = phyCnt1 - aniState->ofdmPhyErrBase;
+ ahp->ah_stats.ast_ani_ofdmerrs +=
+ ofdmPhyErrCnt - aniState->ofdmPhyErrCount;
+ aniState->ofdmPhyErrCount = ofdmPhyErrCnt;
+
+ cckPhyErrCnt = phyCnt2 - aniState->cckPhyErrBase;
+ ahp->ah_stats.ast_ani_cckerrs +=
+ cckPhyErrCnt - aniState->cckPhyErrCount;
+ aniState->cckPhyErrCount = cckPhyErrCnt;
+
+ if (aniState->ofdmPhyErrCount > aniState->ofdmTrigHigh)
+ ath9k_hw_ani_ofdm_err_trigger(ah);
+ if (aniState->cckPhyErrCount > aniState->cckTrigHigh)
+ ath9k_hw_ani_cck_err_trigger(ah);
+
+ ath9k_ani_restart(ah);
+ }
+}
+
+static void ath9k_hw_ani_lower_immunity(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState;
+ int32_t rssi;
+
+ aniState = ahp->ah_curani;
+
+ if (ah->ah_opmode == ATH9K_M_HOSTAP) {
+ if (aniState->firstepLevel > 0) {
+ if (ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel - 1)) {
+ return;
+ }
+ }
+ } else {
+ rssi = BEACON_RSSI(ahp);
+ if (rssi > aniState->rssiThrHigh) {
+ /* XXX: Handle me */
+ } else if (rssi > aniState->rssiThrLow) {
+ if (aniState->ofdmWeakSigDetectOff) {
+ if (ath9k_hw_ani_control(ah,
+ ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION,
+ true) ==
+ true) {
+ return;
+ }
+ }
+ if (aniState->firstepLevel > 0) {
+ if (ath9k_hw_ani_control
+ (ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel - 1) ==
+ true) {
+ return;
+ }
+ }
+ } else {
+ if (aniState->firstepLevel > 0) {
+ if (ath9k_hw_ani_control
+ (ah, ATH9K_ANI_FIRSTEP_LEVEL,
+ aniState->firstepLevel - 1) ==
+ true) {
+ return;
+ }
+ }
+ }
+ }
+
+ if (aniState->spurImmunityLevel > 0) {
+ if (ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL,
+ aniState->spurImmunityLevel - 1)) {
+ return;
+ }
+ }
+
+ if (aniState->noiseImmunityLevel > 0) {
+ ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL,
+ aniState->noiseImmunityLevel - 1);
+ return;
+ }
+}
+
+static int32_t ath9k_hw_ani_get_listen_time(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState;
+ u32 txFrameCount, rxFrameCount, cycleCount;
+ int32_t listenTime;
+
+ txFrameCount = REG_READ(ah, AR_TFCNT);
+ rxFrameCount = REG_READ(ah, AR_RFCNT);
+ cycleCount = REG_READ(ah, AR_CCCNT);
+
+ aniState = ahp->ah_curani;
+ if (aniState->cycleCount == 0 || aniState->cycleCount > cycleCount) {
+
+ listenTime = 0;
+ ahp->ah_stats.ast_ani_lzero++;
+ } else {
+ int32_t ccdelta = cycleCount - aniState->cycleCount;
+ int32_t rfdelta = rxFrameCount - aniState->rxFrameCount;
+ int32_t tfdelta = txFrameCount - aniState->txFrameCount;
+ listenTime = (ccdelta - rfdelta - tfdelta) / 44000;
+ }
+ aniState->cycleCount = cycleCount;
+ aniState->txFrameCount = txFrameCount;
+ aniState->rxFrameCount = rxFrameCount;
+
+ return listenTime;
+}
+
+void ath9k_hw_ani_monitor(struct ath_hal *ah,
+ const struct ath9k_node_stats *stats,
+ struct ath9k_channel *chan)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416AniState *aniState;
+ int32_t listenTime;
+
+ aniState = ahp->ah_curani;
+ ahp->ah_stats.ast_nodestats = *stats;
+
+ listenTime = ath9k_hw_ani_get_listen_time(ah);
+ if (listenTime < 0) {
+ ahp->ah_stats.ast_ani_lneg++;
+ ath9k_ani_restart(ah);
+ return;
+ }
+
+ aniState->listenTime += listenTime;
+
+ if (ahp->ah_hasHwPhyCounters) {
+ u32 phyCnt1, phyCnt2;
+ u32 ofdmPhyErrCnt, cckPhyErrCnt;
+
+ ath9k_hw_update_mibstats(ah, &ahp->ah_mibStats);
+
+ phyCnt1 = REG_READ(ah, AR_PHY_ERR_1);
+ phyCnt2 = REG_READ(ah, AR_PHY_ERR_2);
+
+ if (phyCnt1 < aniState->ofdmPhyErrBase ||
+ phyCnt2 < aniState->cckPhyErrBase) {
+ if (phyCnt1 < aniState->ofdmPhyErrBase) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: phyCnt1 0x%x, resetting "
+ "counter value to 0x%x\n",
+ __func__, phyCnt1,
+ aniState->ofdmPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_1,
+ aniState->ofdmPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_1,
+ AR_PHY_ERR_OFDM_TIMING);
+ }
+ if (phyCnt2 < aniState->cckPhyErrBase) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANI,
+ "%s: phyCnt2 0x%x, resetting "
+ "counter value to 0x%x\n",
+ __func__, phyCnt2,
+ aniState->cckPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_2,
+ aniState->cckPhyErrBase);
+ REG_WRITE(ah, AR_PHY_ERR_MASK_2,
+ AR_PHY_ERR_CCK_TIMING);
+ }
+ return;
+ }
+
+ ofdmPhyErrCnt = phyCnt1 - aniState->ofdmPhyErrBase;
+ ahp->ah_stats.ast_ani_ofdmerrs +=
+ ofdmPhyErrCnt - aniState->ofdmPhyErrCount;
+ aniState->ofdmPhyErrCount = ofdmPhyErrCnt;
+
+ cckPhyErrCnt = phyCnt2 - aniState->cckPhyErrBase;
+ ahp->ah_stats.ast_ani_cckerrs +=
+ cckPhyErrCnt - aniState->cckPhyErrCount;
+ aniState->cckPhyErrCount = cckPhyErrCnt;
+ }
+
+ if (!DO_ANI(ah))
+ return;
+
+ if (aniState->listenTime > 5 * ahp->ah_aniPeriod) {
+ if (aniState->ofdmPhyErrCount <= aniState->listenTime *
+ aniState->ofdmTrigLow / 1000 &&
+ aniState->cckPhyErrCount <= aniState->listenTime *
+ aniState->cckTrigLow / 1000)
+ ath9k_hw_ani_lower_immunity(ah);
+ ath9k_ani_restart(ah);
+ } else if (aniState->listenTime > ahp->ah_aniPeriod) {
+ if (aniState->ofdmPhyErrCount > aniState->listenTime *
+ aniState->ofdmTrigHigh / 1000) {
+ ath9k_hw_ani_ofdm_err_trigger(ah);
+ ath9k_ani_restart(ah);
+ } else if (aniState->cckPhyErrCount >
+ aniState->listenTime * aniState->cckTrigHigh /
+ 1000) {
+ ath9k_hw_ani_cck_err_trigger(ah);
+ ath9k_ani_restart(ah);
+ }
+ }
+}
+
+#ifndef ATH_NF_PER_CHAN
+static void ath9k_init_nfcal_hist_buffer(struct ath_hal *ah)
+{
+ int i, j;
+
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ ah->nfCalHist[i].currIndex = 0;
+ ah->nfCalHist[i].privNF = AR_PHY_CCA_MAX_GOOD_VALUE;
+ ah->nfCalHist[i].invalidNFcount =
+ AR_PHY_CCA_FILTERWINDOW_LENGTH;
+ for (j = 0; j < ATH9K_NF_CAL_HIST_MAX; j++) {
+ ah->nfCalHist[i].nfCalBuffer[j] =
+ AR_PHY_CCA_MAX_GOOD_VALUE;
+ }
+ }
+ return;
+}
+#endif
+
+static void ath9k_hw_gpio_cfg_output_mux(struct ath_hal *ah,
+ u32 gpio, u32 type)
+{
+ int addr;
+ u32 gpio_shift, tmp;
+
+ if (gpio > 11)
+ addr = AR_GPIO_OUTPUT_MUX3;
+ else if (gpio > 5)
+ addr = AR_GPIO_OUTPUT_MUX2;
+ else
+ addr = AR_GPIO_OUTPUT_MUX1;
+
+ gpio_shift = (gpio % 6) * 5;
+
+ if (AR_SREV_9280_20_OR_LATER(ah)
+ || (addr != AR_GPIO_OUTPUT_MUX1)) {
+ REG_RMW(ah, addr, (type << gpio_shift),
+ (0x1f << gpio_shift));
+ } else {
+ tmp = REG_READ(ah, addr);
+ tmp = ((tmp & 0x1F0) << 1) | (tmp & ~0x1F0);
+ tmp &= ~(0x1f << gpio_shift);
+ tmp |= (type << gpio_shift);
+ REG_WRITE(ah, addr, tmp);
+ }
+}
+
+static bool ath9k_hw_cfg_output(struct ath_hal *ah, u32 gpio,
+ enum ath9k_gpio_output_mux_type
+ halSignalType)
+{
+ u32 ah_signal_type;
+ u32 gpio_shift;
+
+ static u32 MuxSignalConversionTable[] = {
+
+ AR_GPIO_OUTPUT_MUX_AS_OUTPUT,
+
+ AR_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED,
+
+ AR_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED,
+
+ AR_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED,
+
+ AR_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED,
+ };
+
+ if ((halSignalType >= 0)
+ && (halSignalType < ARRAY_SIZE(MuxSignalConversionTable)))
+ ah_signal_type = MuxSignalConversionTable[halSignalType];
+ else
+ return false;
+
+ ath9k_hw_gpio_cfg_output_mux(ah, gpio, ah_signal_type);
+
+ gpio_shift = 2 * gpio;
+
+ REG_RMW(ah,
+ AR_GPIO_OE_OUT,
+ (AR_GPIO_OE_OUT_DRV_ALL << gpio_shift),
+ (AR_GPIO_OE_OUT_DRV << gpio_shift));
+
+ return true;
+}
+
+static bool ath9k_hw_set_gpio(struct ath_hal *ah, u32 gpio,
+ u32 val)
+{
+ REG_RMW(ah, AR_GPIO_IN_OUT, ((val & 1) << gpio),
+ AR_GPIO_BIT(gpio));
+ return true;
+}
+
+static u32 ath9k_hw_gpio_get(struct ath_hal *ah, u32 gpio)
+{
+ if (gpio >= ah->ah_caps.num_gpio_pins)
+ return 0xffffffff;
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ return (MS
+ (REG_READ(ah, AR_GPIO_IN_OUT),
+ AR928X_GPIO_IN_VAL) & AR_GPIO_BIT(gpio)) != 0;
+ } else {
+ return (MS(REG_READ(ah, AR_GPIO_IN_OUT), AR_GPIO_IN_VAL) &
+ AR_GPIO_BIT(gpio)) != 0;
+ }
+}
+
+static inline int ath9k_hw_post_attach(struct ath_hal *ah)
+{
+ int ecode;
+
+ if (!ath9k_hw_chip_test(ah)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "%s: hardware self-test failed\n", __func__);
+ return -ENODEV;
+ }
+
+ ecode = ath9k_hw_rf_claim(ah);
+ if (ecode != 0)
+ return ecode;
+
+ ecode = ath9k_hw_eeprom_attach(ah);
+ if (ecode != 0)
+ return ecode;
+ ecode = ath9k_hw_rfattach(ah);
+ if (ecode != 0)
+ return ecode;
+
+ if (!AR_SREV_9100(ah)) {
+ ath9k_hw_ani_setup(ah);
+ ath9k_hw_ani_attach(ah);
+ }
+ return 0;
+}
+
+static u32 ath9k_hw_ini_fixup(struct ath_hal *ah,
+ struct ar5416_eeprom *pEepData,
+ u32 reg, u32 value)
+{
+ struct base_eep_header *pBase = &(pEepData->baseEepHeader);
+
+ switch (ah->ah_devid) {
+ case AR9280_DEVID_PCI:
+ if (reg == 0x7894) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "ini VAL: %x EEPROM: %x\n", value,
+ (pBase->version & 0xff));
+
+ if ((pBase->version & 0xff) > 0x0a) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "PWDCLKIND: %d\n",
+ pBase->pwdclkind);
+ value &= ~AR_AN_TOP2_PWDCLKIND;
+ value |= AR_AN_TOP2_PWDCLKIND & (pBase->
+ pwdclkind << AR_AN_TOP2_PWDCLKIND_S);
+ } else {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "PWDCLKIND Earlier Rev\n");
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "final ini VAL: %x\n", value);
+ }
+ break;
+ }
+ return value;
+}
+
+static bool ath9k_hw_fill_cap_info(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ u16 capField = 0, eeval;
+
+ eeval = ath9k_hw_get_eeprom(ahp, EEP_REG_0);
+
+ ah->ah_currentRD = eeval;
+
+ eeval = ath9k_hw_get_eeprom(ahp, EEP_REG_1);
+ ah->ah_currentRDExt = eeval;
+
+ capField = ath9k_hw_get_eeprom(ahp, EEP_OP_CAP);
+
+ if (ah->ah_opmode != ATH9K_M_HOSTAP &&
+ ah->ah_subvendorid == AR_SUBVENDOR_ID_NEW_A) {
+ if (ah->ah_currentRD == 0x64 || ah->ah_currentRD == 0x65)
+ ah->ah_currentRD += 5;
+ else if (ah->ah_currentRD == 0x41)
+ ah->ah_currentRD = 0x43;
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: regdomain mapped to 0x%x\n", __func__,
+ ah->ah_currentRD);
+ }
+
+ eeval = ath9k_hw_get_eeprom(ahp, EEP_OP_MODE);
+ bitmap_zero(pCap->wireless_modes, ATH9K_MODE_MAX);
+
+ if (eeval & AR5416_OPFLAGS_11A) {
+ set_bit(ATH9K_MODE_11A, pCap->wireless_modes);
+ if (ah->ah_config.ht_enable) {
+ if (!(eeval & AR5416_OPFLAGS_N_5G_HT20))
+ set_bit(ATH9K_MODE_11NA_HT20,
+ pCap->wireless_modes);
+ if (!(eeval & AR5416_OPFLAGS_N_5G_HT40)) {
+ set_bit(ATH9K_MODE_11NA_HT40PLUS,
+ pCap->wireless_modes);
+ set_bit(ATH9K_MODE_11NA_HT40MINUS,
+ pCap->wireless_modes);
+ }
+ }
+ }
+
+ if (eeval & AR5416_OPFLAGS_11G) {
+ set_bit(ATH9K_MODE_11B, pCap->wireless_modes);
+ set_bit(ATH9K_MODE_11G, pCap->wireless_modes);
+ if (ah->ah_config.ht_enable) {
+ if (!(eeval & AR5416_OPFLAGS_N_2G_HT20))
+ set_bit(ATH9K_MODE_11NG_HT20,
+ pCap->wireless_modes);
+ if (!(eeval & AR5416_OPFLAGS_N_2G_HT40)) {
+ set_bit(ATH9K_MODE_11NG_HT40PLUS,
+ pCap->wireless_modes);
+ set_bit(ATH9K_MODE_11NG_HT40MINUS,
+ pCap->wireless_modes);
+ }
+ }
+ }
+
+ pCap->tx_chainmask = ath9k_hw_get_eeprom(ahp, EEP_TX_MASK);
+ if ((ah->ah_isPciExpress)
+ || (eeval & AR5416_OPFLAGS_11A)) {
+ pCap->rx_chainmask =
+ ath9k_hw_get_eeprom(ahp, EEP_RX_MASK);
+ } else {
+ pCap->rx_chainmask =
+ (ath9k_hw_gpio_get(ah, 0)) ? 0x5 : 0x7;
+ }
+
+ if (!(AR_SREV_9280(ah) && (ah->ah_macRev == 0)))
+ ahp->ah_miscMode |= AR_PCU_MIC_NEW_LOC_ENA;
+
+ pCap->low_2ghz_chan = 2312;
+ pCap->high_2ghz_chan = 2732;
+
+ pCap->low_5ghz_chan = 4920;
+ pCap->high_5ghz_chan = 6100;
+
+ pCap->hw_caps &= ~ATH9K_HW_CAP_CIPHER_CKIP;
+ pCap->hw_caps |= ATH9K_HW_CAP_CIPHER_TKIP;
+ pCap->hw_caps |= ATH9K_HW_CAP_CIPHER_AESCCM;
+
+ pCap->hw_caps &= ~ATH9K_HW_CAP_MIC_CKIP;
+ pCap->hw_caps |= ATH9K_HW_CAP_MIC_TKIP;
+ pCap->hw_caps |= ATH9K_HW_CAP_MIC_AESCCM;
+
+ pCap->hw_caps |= ATH9K_HW_CAP_CHAN_SPREAD;
+
+ if (ah->ah_config.ht_enable)
+ pCap->hw_caps |= ATH9K_HW_CAP_HT;
+ else
+ pCap->hw_caps &= ~ATH9K_HW_CAP_HT;
+
+ pCap->hw_caps |= ATH9K_HW_CAP_GTT;
+ pCap->hw_caps |= ATH9K_HW_CAP_VEOL;
+ pCap->hw_caps |= ATH9K_HW_CAP_BSSIDMASK;
+ pCap->hw_caps &= ~ATH9K_HW_CAP_MCAST_KEYSEARCH;
+
+ if (capField & AR_EEPROM_EEPCAP_MAXQCU)
+ pCap->total_queues =
+ MS(capField, AR_EEPROM_EEPCAP_MAXQCU);
+ else
+ pCap->total_queues = ATH9K_NUM_TX_QUEUES;
+
+ if (capField & AR_EEPROM_EEPCAP_KC_ENTRIES)
+ pCap->keycache_size =
+ 1 << MS(capField, AR_EEPROM_EEPCAP_KC_ENTRIES);
+ else
+ pCap->keycache_size = AR_KEYTABLE_SIZE;
+
+ pCap->hw_caps |= ATH9K_HW_CAP_FASTCC;
+ pCap->num_mr_retries = 4;
+ pCap->tx_triglevel_max = MAX_TX_FIFO_THRESHOLD;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ pCap->num_gpio_pins = AR928X_NUM_GPIO;
+ else
+ pCap->num_gpio_pins = AR_NUM_GPIO;
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ pCap->hw_caps |= ATH9K_HW_CAP_WOW;
+ pCap->hw_caps |= ATH9K_HW_CAP_WOW_MATCHPATTERN_EXACT;
+ } else {
+ pCap->hw_caps &= ~ATH9K_HW_CAP_WOW;
+ pCap->hw_caps &= ~ATH9K_HW_CAP_WOW_MATCHPATTERN_EXACT;
+ }
+
+ if (AR_SREV_9160_10_OR_LATER(ah) || AR_SREV_9100(ah)) {
+ pCap->hw_caps |= ATH9K_HW_CAP_CST;
+ pCap->rts_aggr_limit = ATH_AMPDU_LIMIT_MAX;
+ } else {
+ pCap->rts_aggr_limit = (8 * 1024);
+ }
+
+ pCap->hw_caps |= ATH9K_HW_CAP_ENHANCEDPM;
+
+ ah->ah_rfsilent = ath9k_hw_get_eeprom(ahp, EEP_RF_SILENT);
+ if (ah->ah_rfsilent & EEP_RFSILENT_ENABLED) {
+ ahp->ah_gpioSelect =
+ MS(ah->ah_rfsilent, EEP_RFSILENT_GPIO_SEL);
+ ahp->ah_polarity =
+ MS(ah->ah_rfsilent, EEP_RFSILENT_POLARITY);
+
+ ath9k_hw_setcapability(ah, ATH9K_CAP_RFSILENT, 1, true,
+ NULL);
+ pCap->hw_caps |= ATH9K_HW_CAP_RFSILENT;
+ }
+
+ if ((ah->ah_macVersion == AR_SREV_VERSION_5416_PCI) ||
+ (ah->ah_macVersion == AR_SREV_VERSION_5416_PCIE) ||
+ (ah->ah_macVersion == AR_SREV_VERSION_9160) ||
+ (ah->ah_macVersion == AR_SREV_VERSION_9100) ||
+ (ah->ah_macVersion == AR_SREV_VERSION_9280))
+ pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP;
+ else
+ pCap->hw_caps |= ATH9K_HW_CAP_AUTOSLEEP;
+
+ if (AR_SREV_9280(ah))
+ pCap->hw_caps &= ~ATH9K_HW_CAP_4KB_SPLITTRANS;
+ else
+ pCap->hw_caps |= ATH9K_HW_CAP_4KB_SPLITTRANS;
+
+ if (ah->ah_currentRDExt & (1 << REG_EXT_JAPAN_MIDBAND)) {
+ pCap->reg_cap =
+ AR_EEPROM_EEREGCAP_EN_KK_NEW_11A |
+ AR_EEPROM_EEREGCAP_EN_KK_U1_EVEN |
+ AR_EEPROM_EEREGCAP_EN_KK_U2 |
+ AR_EEPROM_EEREGCAP_EN_KK_MIDBAND;
+ } else {
+ pCap->reg_cap =
+ AR_EEPROM_EEREGCAP_EN_KK_NEW_11A |
+ AR_EEPROM_EEREGCAP_EN_KK_U1_EVEN;
+ }
+
+ pCap->reg_cap |= AR_EEPROM_EEREGCAP_EN_FCC_MIDBAND;
+
+ pCap->num_antcfg_5ghz =
+ ath9k_hw_get_num_ant_config(ahp, IEEE80211_BAND_5GHZ);
+ pCap->num_antcfg_2ghz =
+ ath9k_hw_get_num_ant_config(ahp, IEEE80211_BAND_2GHZ);
+
+ return true;
+}
+
+static void ar5416DisablePciePhy(struct ath_hal *ah)
+{
+ if (!AR_SREV_9100(ah))
+ return;
+
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x28000029);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x57160824);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x25980579);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x00000000);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x000e1007);
+
+ REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+}
+
+static void ath9k_set_power_sleep(struct ath_hal *ah, int setChip)
+{
+ REG_SET_BIT(ah, AR_STA_ID1, AR_STA_ID1_PWR_SAV);
+ if (setChip) {
+ REG_CLR_BIT(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_EN);
+ if (!AR_SREV_9100(ah))
+ REG_WRITE(ah, AR_RC, AR_RC_AHB | AR_RC_HOSTIF);
+
+ REG_CLR_BIT(ah, (u16) (AR_RTC_RESET),
+ AR_RTC_RESET_EN);
+ }
+}
+
+static void ath9k_set_power_network_sleep(struct ath_hal *ah, int setChip)
+{
+ REG_SET_BIT(ah, AR_STA_ID1, AR_STA_ID1_PWR_SAV);
+ if (setChip) {
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP)) {
+ REG_WRITE(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_ON_INT);
+ } else {
+ REG_CLR_BIT(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_EN);
+ }
+ }
+}
+
+static bool ath9k_hw_set_power_awake(struct ath_hal *ah,
+ int setChip)
+{
+ u32 val;
+ int i;
+
+ if (setChip) {
+ if ((REG_READ(ah, AR_RTC_STATUS) & AR_RTC_STATUS_M) ==
+ AR_RTC_STATUS_SHUTDOWN) {
+ if (ath9k_hw_set_reset_reg(ah, ATH9K_RESET_POWER_ON)
+ != true) {
+ return false;
+ }
+ }
+ if (AR_SREV_9100(ah))
+ REG_SET_BIT(ah, AR_RTC_RESET,
+ AR_RTC_RESET_EN);
+
+ REG_SET_BIT(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_EN);
+ udelay(50);
+
+ for (i = POWER_UP_TIME / 50; i > 0; i--) {
+ val = REG_READ(ah, AR_RTC_STATUS) & AR_RTC_STATUS_M;
+ if (val == AR_RTC_STATUS_ON)
+ break;
+ udelay(50);
+ REG_SET_BIT(ah, AR_RTC_FORCE_WAKE,
+ AR_RTC_FORCE_WAKE_EN);
+ }
+ if (i == 0) {
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ "%s: Failed to wakeup in %uus\n",
+ __func__, POWER_UP_TIME / 20);
+ return false;
+ }
+ }
+
+ REG_CLR_BIT(ah, AR_STA_ID1, AR_STA_ID1_PWR_SAV);
+ return true;
+}
+
+bool ath9k_hw_setpower(struct ath_hal *ah,
+ enum ath9k_power_mode mode)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ static const char *modes[] = {
+ "AWAKE",
+ "FULL-SLEEP",
+ "NETWORK SLEEP",
+ "UNDEFINED"
+ };
+ int status = true, setChip = true;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT, "%s: %s -> %s (%s)\n", __func__,
+ modes[ahp->ah_powerMode], modes[mode],
+ setChip ? "set chip " : "");
+
+ switch (mode) {
+ case ATH9K_PM_AWAKE:
+ status = ath9k_hw_set_power_awake(ah, setChip);
+ break;
+ case ATH9K_PM_FULL_SLEEP:
+ ath9k_set_power_sleep(ah, setChip);
+ ahp->ah_chipFullSleep = true;
+ break;
+ case ATH9K_PM_NETWORK_SLEEP:
+ ath9k_set_power_network_sleep(ah, setChip);
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ "%s: unknown power mode %u\n", __func__, mode);
+ return false;
+ }
+ ahp->ah_powerMode = mode;
+ return status;
+}
+
+static struct ath_hal *ath9k_hw_do_attach(u16 devid,
+ struct ath_softc *sc,
+ void __iomem *mem,
+ int *status)
+{
+ struct ath_hal_5416 *ahp;
+ struct ath_hal *ah;
+ int ecode;
+#ifndef CONFIG_SLOW_ANT_DIV
+ u32 i;
+ u32 j;
+#endif
+
+ ahp = ath9k_hw_newstate(devid, sc, mem, status);
+ if (ahp == NULL)
+ return NULL;
+
+ ah = &ahp->ah;
+
+ ath9k_hw_set_defaults(ah);
+
+ if (ah->ah_config.intr_mitigation != 0)
+ ahp->ah_intrMitigation = true;
+
+ if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_POWER_ON)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: couldn't reset chip\n",
+ __func__);
+ ecode = -EIO;
+ goto bad;
+ }
+
+ if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: couldn't wakeup chip\n",
+ __func__);
+ ecode = -EIO;
+ goto bad;
+ }
+
+ if (ah->ah_config.serialize_regmode == SER_REG_MODE_AUTO) {
+ if (ah->ah_macVersion == AR_SREV_VERSION_5416_PCI) {
+ ah->ah_config.serialize_regmode =
+ SER_REG_MODE_ON;
+ } else {
+ ah->ah_config.serialize_regmode =
+ SER_REG_MODE_OFF;
+ }
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: serialize_regmode is %d\n",
+ __func__, ah->ah_config.serialize_regmode);
+
+ if ((ah->ah_macVersion != AR_SREV_VERSION_5416_PCI) &&
+ (ah->ah_macVersion != AR_SREV_VERSION_5416_PCIE) &&
+ (ah->ah_macVersion != AR_SREV_VERSION_9160) &&
+ (!AR_SREV_9100(ah)) && (!AR_SREV_9280(ah))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: Mac Chip Rev 0x%02x.%x is not supported by "
+ "this driver\n", __func__,
+ ah->ah_macVersion, ah->ah_macRev);
+ ecode = -EOPNOTSUPP;
+ goto bad;
+ }
+
+ if (AR_SREV_9100(ah)) {
+ ahp->ah_iqCalData.calData = &iq_cal_multi_sample;
+ ahp->ah_suppCals = IQ_MISMATCH_CAL;
+ ah->ah_isPciExpress = false;
+ }
+ ah->ah_phyRev = REG_READ(ah, AR_PHY_CHIP_ID);
+
+ if (AR_SREV_9160_10_OR_LATER(ah)) {
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ ahp->ah_iqCalData.calData = &iq_cal_single_sample;
+ ahp->ah_adcGainCalData.calData =
+ &adc_gain_cal_single_sample;
+ ahp->ah_adcDcCalData.calData =
+ &adc_dc_cal_single_sample;
+ ahp->ah_adcDcCalInitData.calData =
+ &adc_init_dc_cal;
+ } else {
+ ahp->ah_iqCalData.calData = &iq_cal_multi_sample;
+ ahp->ah_adcGainCalData.calData =
+ &adc_gain_cal_multi_sample;
+ ahp->ah_adcDcCalData.calData =
+ &adc_dc_cal_multi_sample;
+ ahp->ah_adcDcCalInitData.calData =
+ &adc_init_dc_cal;
+ }
+ ahp->ah_suppCals =
+ ADC_GAIN_CAL | ADC_DC_CAL | IQ_MISMATCH_CAL;
+ }
+
+ if (AR_SREV_9160(ah)) {
+ ah->ah_config.enable_ani = 1;
+ ahp->ah_ani_function = (ATH9K_ANI_SPUR_IMMUNITY_LEVEL |
+ ATH9K_ANI_FIRSTEP_LEVEL);
+ } else {
+ ahp->ah_ani_function = ATH9K_ANI_ALL;
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ ahp->ah_ani_function &=
+ ~ATH9K_ANI_NOISE_IMMUNITY_LEVEL;
+ }
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: This Mac Chip Rev 0x%02x.%x is \n", __func__,
+ ah->ah_macVersion, ah->ah_macRev);
+
+ if (AR_SREV_9280_20_OR_LATER(ah)) {
+ INIT_INI_ARRAY(&ahp->ah_iniModes, ar9280Modes_9280_2,
+ ARRAY_SIZE(ar9280Modes_9280_2), 6);
+ INIT_INI_ARRAY(&ahp->ah_iniCommon, ar9280Common_9280_2,
+ ARRAY_SIZE(ar9280Common_9280_2), 2);
+
+ if (ah->ah_config.pcie_clock_req) {
+ INIT_INI_ARRAY(&ahp->ah_iniPcieSerdes,
+ ar9280PciePhy_clkreq_off_L1_9280,
+ ARRAY_SIZE
+ (ar9280PciePhy_clkreq_off_L1_9280),
+ 2);
+ } else {
+ INIT_INI_ARRAY(&ahp->ah_iniPcieSerdes,
+ ar9280PciePhy_clkreq_always_on_L1_9280,
+ ARRAY_SIZE
+ (ar9280PciePhy_clkreq_always_on_L1_9280),
+ 2);
+ }
+ INIT_INI_ARRAY(&ahp->ah_iniModesAdditional,
+ ar9280Modes_fast_clock_9280_2,
+ ARRAY_SIZE(ar9280Modes_fast_clock_9280_2),
+ 3);
+ } else if (AR_SREV_9280_10_OR_LATER(ah)) {
+ INIT_INI_ARRAY(&ahp->ah_iniModes, ar9280Modes_9280,
+ ARRAY_SIZE(ar9280Modes_9280), 6);
+ INIT_INI_ARRAY(&ahp->ah_iniCommon, ar9280Common_9280,
+ ARRAY_SIZE(ar9280Common_9280), 2);
+ } else if (AR_SREV_9160_10_OR_LATER(ah)) {
+ INIT_INI_ARRAY(&ahp->ah_iniModes, ar5416Modes_9160,
+ ARRAY_SIZE(ar5416Modes_9160), 6);
+ INIT_INI_ARRAY(&ahp->ah_iniCommon, ar5416Common_9160,
+ ARRAY_SIZE(ar5416Common_9160), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank0, ar5416Bank0_9160,
+ ARRAY_SIZE(ar5416Bank0_9160), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBB_RfGain, ar5416BB_RfGain_9160,
+ ARRAY_SIZE(ar5416BB_RfGain_9160), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank1, ar5416Bank1_9160,
+ ARRAY_SIZE(ar5416Bank1_9160), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank2, ar5416Bank2_9160,
+ ARRAY_SIZE(ar5416Bank2_9160), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank3, ar5416Bank3_9160,
+ ARRAY_SIZE(ar5416Bank3_9160), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6, ar5416Bank6_9160,
+ ARRAY_SIZE(ar5416Bank6_9160), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6TPC, ar5416Bank6TPC_9160,
+ ARRAY_SIZE(ar5416Bank6TPC_9160), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank7, ar5416Bank7_9160,
+ ARRAY_SIZE(ar5416Bank7_9160), 2);
+ if (AR_SREV_9160_11(ah)) {
+ INIT_INI_ARRAY(&ahp->ah_iniAddac,
+ ar5416Addac_91601_1,
+ ARRAY_SIZE(ar5416Addac_91601_1), 2);
+ } else {
+ INIT_INI_ARRAY(&ahp->ah_iniAddac, ar5416Addac_9160,
+ ARRAY_SIZE(ar5416Addac_9160), 2);
+ }
+ } else if (AR_SREV_9100_OR_LATER(ah)) {
+ INIT_INI_ARRAY(&ahp->ah_iniModes, ar5416Modes_9100,
+ ARRAY_SIZE(ar5416Modes_9100), 6);
+ INIT_INI_ARRAY(&ahp->ah_iniCommon, ar5416Common_9100,
+ ARRAY_SIZE(ar5416Common_9100), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank0, ar5416Bank0_9100,
+ ARRAY_SIZE(ar5416Bank0_9100), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBB_RfGain, ar5416BB_RfGain_9100,
+ ARRAY_SIZE(ar5416BB_RfGain_9100), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank1, ar5416Bank1_9100,
+ ARRAY_SIZE(ar5416Bank1_9100), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank2, ar5416Bank2_9100,
+ ARRAY_SIZE(ar5416Bank2_9100), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank3, ar5416Bank3_9100,
+ ARRAY_SIZE(ar5416Bank3_9100), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6, ar5416Bank6_9100,
+ ARRAY_SIZE(ar5416Bank6_9100), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6TPC, ar5416Bank6TPC_9100,
+ ARRAY_SIZE(ar5416Bank6TPC_9100), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank7, ar5416Bank7_9100,
+ ARRAY_SIZE(ar5416Bank7_9100), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniAddac, ar5416Addac_9100,
+ ARRAY_SIZE(ar5416Addac_9100), 2);
+ } else {
+ INIT_INI_ARRAY(&ahp->ah_iniModes, ar5416Modes,
+ ARRAY_SIZE(ar5416Modes), 6);
+ INIT_INI_ARRAY(&ahp->ah_iniCommon, ar5416Common,
+ ARRAY_SIZE(ar5416Common), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank0, ar5416Bank0,
+ ARRAY_SIZE(ar5416Bank0), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBB_RfGain, ar5416BB_RfGain,
+ ARRAY_SIZE(ar5416BB_RfGain), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank1, ar5416Bank1,
+ ARRAY_SIZE(ar5416Bank1), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank2, ar5416Bank2,
+ ARRAY_SIZE(ar5416Bank2), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniBank3, ar5416Bank3,
+ ARRAY_SIZE(ar5416Bank3), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6, ar5416Bank6,
+ ARRAY_SIZE(ar5416Bank6), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank6TPC, ar5416Bank6TPC,
+ ARRAY_SIZE(ar5416Bank6TPC), 3);
+ INIT_INI_ARRAY(&ahp->ah_iniBank7, ar5416Bank7,
+ ARRAY_SIZE(ar5416Bank7), 2);
+ INIT_INI_ARRAY(&ahp->ah_iniAddac, ar5416Addac,
+ ARRAY_SIZE(ar5416Addac), 2);
+ }
+
+ if (ah->ah_isPciExpress)
+ ath9k_hw_configpcipowersave(ah, 0);
+ else
+ ar5416DisablePciePhy(ah);
+
+ ecode = ath9k_hw_post_attach(ah);
+ if (ecode != 0)
+ goto bad;
+
+#ifndef CONFIG_SLOW_ANT_DIV
+ if (ah->ah_devid == AR9280_DEVID_PCI) {
+ for (i = 0; i < ahp->ah_iniModes.ia_rows; i++) {
+ u32 reg = INI_RA(&ahp->ah_iniModes, i, 0);
+
+ for (j = 1; j < ahp->ah_iniModes.ia_columns; j++) {
+ u32 val = INI_RA(&ahp->ah_iniModes, i, j);
+
+ INI_RA(&ahp->ah_iniModes, i, j) =
+ ath9k_hw_ini_fixup(ah, &ahp->ah_eeprom,
+ reg, val);
+ }
+ }
+ }
+#endif
+
+ if (!ath9k_hw_fill_cap_info(ah)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s:failed ath9k_hw_fill_cap_info\n", __func__);
+ ecode = -EINVAL;
+ goto bad;
+ }
+
+ ecode = ath9k_hw_init_macaddr(ah);
+ if (ecode != 0) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: failed initializing mac address\n",
+ __func__);
+ goto bad;
+ }
+
+ if (AR_SREV_9285(ah))
+ ah->ah_txTrigLevel = (AR_FTRIG_256B >> AR_FTRIG_S);
+ else
+ ah->ah_txTrigLevel = (AR_FTRIG_512B >> AR_FTRIG_S);
+
+#ifndef ATH_NF_PER_CHAN
+
+ ath9k_init_nfcal_hist_buffer(ah);
+#endif
+
+ return ah;
+
+bad:
+ if (ahp)
+ ath9k_hw_detach((struct ath_hal *) ahp);
+ if (status)
+ *status = ecode;
+ return NULL;
+}
+
+void ath9k_hw_detach(struct ath_hal *ah)
+{
+ if (!AR_SREV_9100(ah))
+ ath9k_hw_ani_detach(ah);
+ ath9k_hw_rfdetach(ah);
+
+ ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP);
+ kfree(ah);
+}
+
+bool ath9k_get_channel_edges(struct ath_hal *ah,
+ u16 flags, u16 *low,
+ u16 *high)
+{
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ if (flags & CHANNEL_5GHZ) {
+ *low = pCap->low_5ghz_chan;
+ *high = pCap->high_5ghz_chan;
+ return true;
+ }
+ if ((flags & CHANNEL_2GHZ)) {
+ *low = pCap->low_2ghz_chan;
+ *high = pCap->high_2ghz_chan;
+
+ return true;
+ }
+ return false;
+}
+
+static inline bool ath9k_hw_fill_vpd_table(u8 pwrMin,
+ u8 pwrMax,
+ u8 *pPwrList,
+ u8 *pVpdList,
+ u16
+ numIntercepts,
+ u8 *pRetVpdList)
+{
+ u16 i, k;
+ u8 currPwr = pwrMin;
+ u16 idxL = 0, idxR = 0;
+
+ for (i = 0; i <= (pwrMax - pwrMin) / 2; i++) {
+ ath9k_hw_get_lower_upper_index(currPwr, pPwrList,
+ numIntercepts, &(idxL),
+ &(idxR));
+ if (idxR < 1)
+ idxR = 1;
+ if (idxL == numIntercepts - 1)
+ idxL = (u16) (numIntercepts - 2);
+ if (pPwrList[idxL] == pPwrList[idxR])
+ k = pVpdList[idxL];
+ else
+ k = (u16) (((currPwr -
+ pPwrList[idxL]) *
+ pVpdList[idxR] +
+ (pPwrList[idxR] -
+ currPwr) * pVpdList[idxL]) /
+ (pPwrList[idxR] -
+ pPwrList[idxL]));
+ pRetVpdList[i] = (u8) k;
+ currPwr += 2;
+ }
+
+ return true;
+}
+
+static inline void
+ath9k_hw_get_gain_boundaries_pdadcs(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ struct cal_data_per_freq *pRawDataSet,
+ u8 *bChans,
+ u16 availPiers,
+ u16 tPdGainOverlap,
+ int16_t *pMinCalPower,
+ u16 *pPdGainBoundaries,
+ u8 *pPDADCValues,
+ u16 numXpdGains)
+{
+ int i, j, k;
+ int16_t ss;
+ u16 idxL = 0, idxR = 0, numPiers;
+ static u8 vpdTableL[AR5416_NUM_PD_GAINS]
+ [AR5416_MAX_PWR_RANGE_IN_HALF_DB];
+ static u8 vpdTableR[AR5416_NUM_PD_GAINS]
+ [AR5416_MAX_PWR_RANGE_IN_HALF_DB];
+ static u8 vpdTableI[AR5416_NUM_PD_GAINS]
+ [AR5416_MAX_PWR_RANGE_IN_HALF_DB];
+
+ u8 *pVpdL, *pVpdR, *pPwrL, *pPwrR;
+ u8 minPwrT4[AR5416_NUM_PD_GAINS];
+ u8 maxPwrT4[AR5416_NUM_PD_GAINS];
+ int16_t vpdStep;
+ int16_t tmpVal;
+ u16 sizeCurrVpdTable, maxIndex, tgtIndex;
+ bool match;
+ int16_t minDelta = 0;
+ struct chan_centers centers;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+
+ for (numPiers = 0; numPiers < availPiers; numPiers++) {
+ if (bChans[numPiers] == AR5416_BCHAN_UNUSED)
+ break;
+ }
+
+ match = ath9k_hw_get_lower_upper_index((u8)
+ FREQ2FBIN(centers.
+ synth_center,
+ IS_CHAN_2GHZ
+ (chan)), bChans,
+ numPiers, &idxL, &idxR);
+
+ if (match) {
+ for (i = 0; i < numXpdGains; i++) {
+ minPwrT4[i] = pRawDataSet[idxL].pwrPdg[i][0];
+ maxPwrT4[i] = pRawDataSet[idxL].pwrPdg[i][4];
+ ath9k_hw_fill_vpd_table(minPwrT4[i], maxPwrT4[i],
+ pRawDataSet[idxL].
+ pwrPdg[i],
+ pRawDataSet[idxL].
+ vpdPdg[i],
+ AR5416_PD_GAIN_ICEPTS,
+ vpdTableI[i]);
+ }
+ } else {
+ for (i = 0; i < numXpdGains; i++) {
+ pVpdL = pRawDataSet[idxL].vpdPdg[i];
+ pPwrL = pRawDataSet[idxL].pwrPdg[i];
+ pVpdR = pRawDataSet[idxR].vpdPdg[i];
+ pPwrR = pRawDataSet[idxR].pwrPdg[i];
+
+ minPwrT4[i] = max(pPwrL[0], pPwrR[0]);
+
+ maxPwrT4[i] =
+ min(pPwrL[AR5416_PD_GAIN_ICEPTS - 1],
+ pPwrR[AR5416_PD_GAIN_ICEPTS - 1]);
+
+
+ ath9k_hw_fill_vpd_table(minPwrT4[i], maxPwrT4[i],
+ pPwrL, pVpdL,
+ AR5416_PD_GAIN_ICEPTS,
+ vpdTableL[i]);
+ ath9k_hw_fill_vpd_table(minPwrT4[i], maxPwrT4[i],
+ pPwrR, pVpdR,
+ AR5416_PD_GAIN_ICEPTS,
+ vpdTableR[i]);
+
+ for (j = 0; j <= (maxPwrT4[i] - minPwrT4[i]) / 2; j++) {
+ vpdTableI[i][j] =
+ (u8) (ath9k_hw_interpolate
+ ((u16)
+ FREQ2FBIN(centers.
+ synth_center,
+ IS_CHAN_2GHZ
+ (chan)),
+ bChans[idxL],
+ bChans[idxR], vpdTableL[i]
+ [j], vpdTableR[i]
+ [j]));
+ }
+ }
+ }
+
+ *pMinCalPower = (int16_t) (minPwrT4[0] / 2);
+
+ k = 0;
+ for (i = 0; i < numXpdGains; i++) {
+ if (i == (numXpdGains - 1))
+ pPdGainBoundaries[i] =
+ (u16) (maxPwrT4[i] / 2);
+ else
+ pPdGainBoundaries[i] =
+ (u16) ((maxPwrT4[i] +
+ minPwrT4[i + 1]) / 4);
+
+ pPdGainBoundaries[i] =
+ min((u16) AR5416_MAX_RATE_POWER,
+ pPdGainBoundaries[i]);
+
+ if ((i == 0) && !AR_SREV_5416_V20_OR_LATER(ah)) {
+ minDelta = pPdGainBoundaries[0] - 23;
+ pPdGainBoundaries[0] = 23;
+ } else {
+ minDelta = 0;
+ }
+
+ if (i == 0) {
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ ss = (int16_t) (0 - (minPwrT4[i] / 2));
+ else
+ ss = 0;
+ } else {
+ ss = (int16_t) ((pPdGainBoundaries[i - 1] -
+ (minPwrT4[i] / 2)) -
+ tPdGainOverlap + 1 + minDelta);
+ }
+ vpdStep = (int16_t) (vpdTableI[i][1] - vpdTableI[i][0]);
+ vpdStep = (int16_t) ((vpdStep < 1) ? 1 : vpdStep);
+
+ while ((ss < 0) && (k < (AR5416_NUM_PDADC_VALUES - 1))) {
+ tmpVal = (int16_t) (vpdTableI[i][0] + ss * vpdStep);
+ pPDADCValues[k++] =
+ (u8) ((tmpVal < 0) ? 0 : tmpVal);
+ ss++;
+ }
+
+ sizeCurrVpdTable =
+ (u8) ((maxPwrT4[i] - minPwrT4[i]) / 2 + 1);
+ tgtIndex = (u8) (pPdGainBoundaries[i] + tPdGainOverlap -
+ (minPwrT4[i] / 2));
+ maxIndex = (tgtIndex <
+ sizeCurrVpdTable) ? tgtIndex : sizeCurrVpdTable;
+
+ while ((ss < maxIndex)
+ && (k < (AR5416_NUM_PDADC_VALUES - 1))) {
+ pPDADCValues[k++] = vpdTableI[i][ss++];
+ }
+
+ vpdStep = (int16_t) (vpdTableI[i][sizeCurrVpdTable - 1] -
+ vpdTableI[i][sizeCurrVpdTable - 2]);
+ vpdStep = (int16_t) ((vpdStep < 1) ? 1 : vpdStep);
+
+ if (tgtIndex > maxIndex) {
+ while ((ss <= tgtIndex)
+ && (k < (AR5416_NUM_PDADC_VALUES - 1))) {
+ tmpVal = (int16_t) ((vpdTableI[i]
+ [sizeCurrVpdTable -
+ 1] + (ss - maxIndex +
+ 1) * vpdStep));
+ pPDADCValues[k++] = (u8) ((tmpVal >
+ 255) ? 255 : tmpVal);
+ ss++;
+ }
+ }
+ }
+
+ while (i < AR5416_PD_GAINS_IN_MASK) {
+ pPdGainBoundaries[i] = pPdGainBoundaries[i - 1];
+ i++;
+ }
+
+ while (k < AR5416_NUM_PDADC_VALUES) {
+ pPDADCValues[k] = pPDADCValues[k - 1];
+ k++;
+ }
+ return;
+}
+
+static inline bool
+ath9k_hw_set_power_cal_table(struct ath_hal *ah,
+ struct ar5416_eeprom *pEepData,
+ struct ath9k_channel *chan,
+ int16_t *pTxPowerIndexOffset)
+{
+ struct cal_data_per_freq *pRawDataset;
+ u8 *pCalBChans = NULL;
+ u16 pdGainOverlap_t2;
+ static u8 pdadcValues[AR5416_NUM_PDADC_VALUES];
+ u16 gainBoundaries[AR5416_PD_GAINS_IN_MASK];
+ u16 numPiers, i, j;
+ int16_t tMinCalPower;
+ u16 numXpdGain, xpdMask;
+ u16 xpdGainValues[AR5416_NUM_PD_GAINS] = { 0, 0, 0, 0 };
+ u32 reg32, regOffset, regChainOffset;
+ int16_t modalIdx;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ modalIdx = IS_CHAN_2GHZ(chan) ? 1 : 0;
+ xpdMask = pEepData->modalHeader[modalIdx].xpdGain;
+
+ if ((pEepData->baseEepHeader.
+ version & AR5416_EEP_VER_MINOR_MASK) >=
+ AR5416_EEP_MINOR_VER_2) {
+ pdGainOverlap_t2 =
+ pEepData->modalHeader[modalIdx].pdGainOverlap;
+ } else {
+ pdGainOverlap_t2 =
+ (u16) (MS
+ (REG_READ(ah, AR_PHY_TPCRG5),
+ AR_PHY_TPCRG5_PD_GAIN_OVERLAP));
+ }
+
+ if (IS_CHAN_2GHZ(chan)) {
+ pCalBChans = pEepData->calFreqPier2G;
+ numPiers = AR5416_NUM_2G_CAL_PIERS;
+ } else {
+ pCalBChans = pEepData->calFreqPier5G;
+ numPiers = AR5416_NUM_5G_CAL_PIERS;
+ }
+
+ numXpdGain = 0;
+
+ for (i = 1; i <= AR5416_PD_GAINS_IN_MASK; i++) {
+ if ((xpdMask >> (AR5416_PD_GAINS_IN_MASK - i)) & 1) {
+ if (numXpdGain >= AR5416_NUM_PD_GAINS)
+ break;
+ xpdGainValues[numXpdGain] =
+ (u16) (AR5416_PD_GAINS_IN_MASK - i);
+ numXpdGain++;
+ }
+ }
+
+ REG_RMW_FIELD(ah, AR_PHY_TPCRG1, AR_PHY_TPCRG1_NUM_PD_GAIN,
+ (numXpdGain - 1) & 0x3);
+ REG_RMW_FIELD(ah, AR_PHY_TPCRG1, AR_PHY_TPCRG1_PD_GAIN_1,
+ xpdGainValues[0]);
+ REG_RMW_FIELD(ah, AR_PHY_TPCRG1, AR_PHY_TPCRG1_PD_GAIN_2,
+ xpdGainValues[1]);
+ REG_RMW_FIELD(ah, AR_PHY_TPCRG1, AR_PHY_TPCRG1_PD_GAIN_3,
+ xpdGainValues[2]);
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ if (AR_SREV_5416_V20_OR_LATER(ah) &&
+ (ahp->ah_rxchainmask == 5 || ahp->ah_txchainmask == 5)
+ && (i != 0)) {
+ regChainOffset = (i == 1) ? 0x2000 : 0x1000;
+ } else
+ regChainOffset = i * 0x1000;
+ if (pEepData->baseEepHeader.txMask & (1 << i)) {
+ if (IS_CHAN_2GHZ(chan))
+ pRawDataset = pEepData->calPierData2G[i];
+ else
+ pRawDataset = pEepData->calPierData5G[i];
+
+ ath9k_hw_get_gain_boundaries_pdadcs(ah, chan,
+ pRawDataset,
+ pCalBChans,
+ numPiers,
+ pdGainOverlap_t2,
+ &tMinCalPower,
+ gainBoundaries,
+ pdadcValues,
+ numXpdGain);
+
+ if ((i == 0) || AR_SREV_5416_V20_OR_LATER(ah)) {
+
+ REG_WRITE(ah,
+ AR_PHY_TPCRG5 + regChainOffset,
+ SM(pdGainOverlap_t2,
+ AR_PHY_TPCRG5_PD_GAIN_OVERLAP)
+ | SM(gainBoundaries[0],
+ AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_1)
+ | SM(gainBoundaries[1],
+ AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_2)
+ | SM(gainBoundaries[2],
+ AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_3)
+ | SM(gainBoundaries[3],
+ AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_4));
+ }
+
+ regOffset =
+ AR_PHY_BASE + (672 << 2) + regChainOffset;
+ for (j = 0; j < 32; j++) {
+ reg32 =
+ ((pdadcValues[4 * j + 0] & 0xFF) << 0)
+ | ((pdadcValues[4 * j + 1] & 0xFF) <<
+ 8) | ((pdadcValues[4 * j + 2] &
+ 0xFF) << 16) |
+ ((pdadcValues[4 * j + 3] & 0xFF) <<
+ 24);
+ REG_WRITE(ah, regOffset, reg32);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_PHY_IO,
+ "PDADC (%d,%4x): %4.4x %8.8x\n",
+ i, regChainOffset, regOffset,
+ reg32);
+ DPRINTF(ah->ah_sc, ATH_DBG_PHY_IO,
+ "PDADC: Chain %d | PDADC %3d Value %3d | "
+ "PDADC %3d Value %3d | PDADC %3d Value %3d | "
+ "PDADC %3d Value %3d |\n",
+ i, 4 * j, pdadcValues[4 * j],
+ 4 * j + 1, pdadcValues[4 * j + 1],
+ 4 * j + 2, pdadcValues[4 * j + 2],
+ 4 * j + 3,
+ pdadcValues[4 * j + 3]);
+
+ regOffset += 4;
+ }
+ }
+ }
+ *pTxPowerIndexOffset = 0;
+
+ return true;
+}
+
+void ath9k_hw_configpcipowersave(struct ath_hal *ah, int restore)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u8 i;
+
+ if (ah->ah_isPciExpress != true)
+ return;
+
+ if (ah->ah_config.pcie_powersave_enable == 2)
+ return;
+
+ if (restore)
+ return;
+
+ if (AR_SREV_9280_20_OR_LATER(ah)) {
+ for (i = 0; i < ahp->ah_iniPcieSerdes.ia_rows; i++) {
+ REG_WRITE(ah, INI_RA(&ahp->ah_iniPcieSerdes, i, 0),
+ INI_RA(&ahp->ah_iniPcieSerdes, i, 1));
+ }
+ udelay(1000);
+ } else if (AR_SREV_9280(ah)
+ && (ah->ah_macRev == AR_SREV_REVISION_9280_10)) {
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
+
+ if (ah->ah_config.pcie_clock_req)
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
+ else
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd);
+
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
+
+ REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+
+ udelay(1000);
+ } else {
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
+ REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+ }
+
+ REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
+
+ if (ah->ah_config.pcie_waen) {
+ REG_WRITE(ah, AR_WA, ah->ah_config.pcie_waen);
+ } else {
+ if (AR_SREV_9280(ah))
+ REG_WRITE(ah, AR_WA, 0x0040073f);
+ else
+ REG_WRITE(ah, AR_WA, 0x0000073f);
+ }
+}
+
+static inline void
+ath9k_hw_get_legacy_target_powers(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ struct cal_target_power_leg *powInfo,
+ u16 numChannels,
+ struct cal_target_power_leg *pNewPower,
+ u16 numRates,
+ bool isExtTarget)
+{
+ u16 clo, chi;
+ int i;
+ int matchIndex = -1, lowIndex = -1;
+ u16 freq;
+ struct chan_centers centers;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ freq = (isExtTarget) ? centers.ext_center : centers.ctl_center;
+
+ if (freq <= ath9k_hw_fbin2freq(powInfo[0].bChannel,
+ IS_CHAN_2GHZ(chan))) {
+ matchIndex = 0;
+ } else {
+ for (i = 0; (i < numChannels)
+ && (powInfo[i].bChannel != AR5416_BCHAN_UNUSED); i++) {
+ if (freq ==
+ ath9k_hw_fbin2freq(powInfo[i].bChannel,
+ IS_CHAN_2GHZ(chan))) {
+ matchIndex = i;
+ break;
+ } else if ((freq <
+ ath9k_hw_fbin2freq(powInfo[i].bChannel,
+ IS_CHAN_2GHZ(chan)))
+ && (freq >
+ ath9k_hw_fbin2freq(powInfo[i - 1].
+ bChannel,
+ IS_CHAN_2GHZ
+ (chan)))) {
+ lowIndex = i - 1;
+ break;
+ }
+ }
+ if ((matchIndex == -1) && (lowIndex == -1))
+ matchIndex = i - 1;
+ }
+
+ if (matchIndex != -1) {
+ *pNewPower = powInfo[matchIndex];
+ } else {
+ clo = ath9k_hw_fbin2freq(powInfo[lowIndex].bChannel,
+ IS_CHAN_2GHZ(chan));
+ chi = ath9k_hw_fbin2freq(powInfo[lowIndex + 1].bChannel,
+ IS_CHAN_2GHZ(chan));
+
+ for (i = 0; i < numRates; i++) {
+ pNewPower->tPow2x[i] =
+ (u8) ath9k_hw_interpolate(freq, clo, chi,
+ powInfo
+ [lowIndex].
+ tPow2x[i],
+ powInfo
+ [lowIndex +
+ 1].tPow2x[i]);
+ }
+ }
+}
+
+static inline void
+ath9k_hw_get_target_powers(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ struct cal_target_power_ht *powInfo,
+ u16 numChannels,
+ struct cal_target_power_ht *pNewPower,
+ u16 numRates,
+ bool isHt40Target)
+{
+ u16 clo, chi;
+ int i;
+ int matchIndex = -1, lowIndex = -1;
+ u16 freq;
+ struct chan_centers centers;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ freq = isHt40Target ? centers.synth_center : centers.ctl_center;
+
+ if (freq <=
+ ath9k_hw_fbin2freq(powInfo[0].bChannel, IS_CHAN_2GHZ(chan))) {
+ matchIndex = 0;
+ } else {
+ for (i = 0; (i < numChannels)
+ && (powInfo[i].bChannel != AR5416_BCHAN_UNUSED); i++) {
+ if (freq ==
+ ath9k_hw_fbin2freq(powInfo[i].bChannel,
+ IS_CHAN_2GHZ(chan))) {
+ matchIndex = i;
+ break;
+ } else
+ if ((freq <
+ ath9k_hw_fbin2freq(powInfo[i].bChannel,
+ IS_CHAN_2GHZ(chan)))
+ && (freq >
+ ath9k_hw_fbin2freq(powInfo[i - 1].
+ bChannel,
+ IS_CHAN_2GHZ
+ (chan)))) {
+ lowIndex = i - 1;
+ break;
+ }
+ }
+ if ((matchIndex == -1) && (lowIndex == -1))
+ matchIndex = i - 1;
+ }
+
+ if (matchIndex != -1) {
+ *pNewPower = powInfo[matchIndex];
+ } else {
+ clo = ath9k_hw_fbin2freq(powInfo[lowIndex].bChannel,
+ IS_CHAN_2GHZ(chan));
+ chi = ath9k_hw_fbin2freq(powInfo[lowIndex + 1].bChannel,
+ IS_CHAN_2GHZ(chan));
+
+ for (i = 0; i < numRates; i++) {
+ pNewPower->tPow2x[i] =
+ (u8) ath9k_hw_interpolate(freq, clo, chi,
+ powInfo
+ [lowIndex].
+ tPow2x[i],
+ powInfo
+ [lowIndex +
+ 1].tPow2x[i]);
+ }
+ }
+}
+
+static inline u16
+ath9k_hw_get_max_edge_power(u16 freq,
+ struct cal_ctl_edges *pRdEdgesPower,
+ bool is2GHz)
+{
+ u16 twiceMaxEdgePower = AR5416_MAX_RATE_POWER;
+ int i;
+
+ for (i = 0; (i < AR5416_NUM_BAND_EDGES)
+ && (pRdEdgesPower[i].bChannel != AR5416_BCHAN_UNUSED); i++) {
+ if (freq == ath9k_hw_fbin2freq(pRdEdgesPower[i].bChannel,
+ is2GHz)) {
+ twiceMaxEdgePower = pRdEdgesPower[i].tPower;
+ break;
+ } else if ((i > 0)
+ && (freq <
+ ath9k_hw_fbin2freq(pRdEdgesPower[i].
+ bChannel, is2GHz))) {
+ if (ath9k_hw_fbin2freq
+ (pRdEdgesPower[i - 1].bChannel, is2GHz) < freq
+ && pRdEdgesPower[i - 1].flag) {
+ twiceMaxEdgePower =
+ pRdEdgesPower[i - 1].tPower;
+ }
+ break;
+ }
+ }
+ return twiceMaxEdgePower;
+}
+
+static inline bool
+ath9k_hw_set_power_per_rate_table(struct ath_hal *ah,
+ struct ar5416_eeprom *pEepData,
+ struct ath9k_channel *chan,
+ int16_t *ratesArray,
+ u16 cfgCtl,
+ u8 AntennaReduction,
+ u8 twiceMaxRegulatoryPower,
+ u8 powerLimit)
+{
+ u8 twiceMaxEdgePower = AR5416_MAX_RATE_POWER;
+ static const u16 tpScaleReductionTable[5] =
+ { 0, 3, 6, 9, AR5416_MAX_RATE_POWER };
+
+ int i;
+ int8_t twiceLargestAntenna;
+ struct cal_ctl_data *rep;
+ struct cal_target_power_leg targetPowerOfdm, targetPowerCck = {
+ 0, { 0, 0, 0, 0}
+ };
+ struct cal_target_power_leg targetPowerOfdmExt = {
+ 0, { 0, 0, 0, 0} }, targetPowerCckExt = {
+ 0, { 0, 0, 0, 0 }
+ };
+ struct cal_target_power_ht targetPowerHt20, targetPowerHt40 = {
+ 0, {0, 0, 0, 0}
+ };
+ u8 scaledPower = 0, minCtlPower, maxRegAllowedPower;
+ u16 ctlModesFor11a[] =
+ { CTL_11A, CTL_5GHT20, CTL_11A_EXT, CTL_5GHT40 };
+ u16 ctlModesFor11g[] =
+ { CTL_11B, CTL_11G, CTL_2GHT20, CTL_11B_EXT, CTL_11G_EXT,
+ CTL_2GHT40
+ };
+ u16 numCtlModes, *pCtlMode, ctlMode, freq;
+ struct chan_centers centers;
+ int tx_chainmask;
+ u8 twiceMinEdgePower;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ tx_chainmask = ahp->ah_txchainmask;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+
+ twiceLargestAntenna = max(
+ pEepData->modalHeader
+ [IS_CHAN_2GHZ(chan)].antennaGainCh[0],
+ pEepData->modalHeader
+ [IS_CHAN_2GHZ(chan)].antennaGainCh[1]);
+
+ twiceLargestAntenna = max((u8) twiceLargestAntenna,
+ pEepData->modalHeader
+ [IS_CHAN_2GHZ(chan)].antennaGainCh[2]);
+
+ twiceLargestAntenna =
+ (int8_t) min(AntennaReduction - twiceLargestAntenna, 0);
+
+ maxRegAllowedPower = twiceMaxRegulatoryPower + twiceLargestAntenna;
+
+ if (ah->ah_tpScale != ATH9K_TP_SCALE_MAX) {
+ maxRegAllowedPower -=
+ (tpScaleReductionTable[(ah->ah_tpScale)] * 2);
+ }
+
+ scaledPower = min(powerLimit, maxRegAllowedPower);
+
+ switch (ar5416_get_ntxchains(tx_chainmask)) {
+ case 1:
+ break;
+ case 2:
+ scaledPower -=
+ pEepData->modalHeader[IS_CHAN_2GHZ(chan)].
+ pwrDecreaseFor2Chain;
+ break;
+ case 3:
+ scaledPower -=
+ pEepData->modalHeader[IS_CHAN_2GHZ(chan)].
+ pwrDecreaseFor3Chain;
+ break;
+ }
+
+ scaledPower = max(0, (int32_t) scaledPower);
+
+ if (IS_CHAN_2GHZ(chan)) {
+ numCtlModes =
+ ARRAY_SIZE(ctlModesFor11g) -
+ SUB_NUM_CTL_MODES_AT_2G_40;
+ pCtlMode = ctlModesFor11g;
+
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPowerCck,
+ AR5416_NUM_2G_CCK_TARGET_POWERS,
+ &targetPowerCck, 4,
+ false);
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPower2G,
+ AR5416_NUM_2G_20_TARGET_POWERS,
+ &targetPowerOfdm, 4,
+ false);
+ ath9k_hw_get_target_powers(ah, chan,
+ pEepData->calTargetPower2GHT20,
+ AR5416_NUM_2G_20_TARGET_POWERS,
+ &targetPowerHt20, 8, false);
+
+ if (IS_CHAN_HT40(chan)) {
+ numCtlModes = ARRAY_SIZE(ctlModesFor11g);
+ ath9k_hw_get_target_powers(ah, chan,
+ pEepData->
+ calTargetPower2GHT40,
+ AR5416_NUM_2G_40_TARGET_POWERS,
+ &targetPowerHt40, 8,
+ true);
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPowerCck,
+ AR5416_NUM_2G_CCK_TARGET_POWERS,
+ &targetPowerCckExt,
+ 4, true);
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPower2G,
+ AR5416_NUM_2G_20_TARGET_POWERS,
+ &targetPowerOfdmExt,
+ 4, true);
+ }
+ } else {
+
+ numCtlModes =
+ ARRAY_SIZE(ctlModesFor11a) -
+ SUB_NUM_CTL_MODES_AT_5G_40;
+ pCtlMode = ctlModesFor11a;
+
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPower5G,
+ AR5416_NUM_5G_20_TARGET_POWERS,
+ &targetPowerOfdm, 4,
+ false);
+ ath9k_hw_get_target_powers(ah, chan,
+ pEepData->calTargetPower5GHT20,
+ AR5416_NUM_5G_20_TARGET_POWERS,
+ &targetPowerHt20, 8, false);
+
+ if (IS_CHAN_HT40(chan)) {
+ numCtlModes = ARRAY_SIZE(ctlModesFor11a);
+ ath9k_hw_get_target_powers(ah, chan,
+ pEepData->
+ calTargetPower5GHT40,
+ AR5416_NUM_5G_40_TARGET_POWERS,
+ &targetPowerHt40, 8,
+ true);
+ ath9k_hw_get_legacy_target_powers(ah, chan,
+ pEepData->
+ calTargetPower5G,
+ AR5416_NUM_5G_20_TARGET_POWERS,
+ &targetPowerOfdmExt,
+ 4, true);
+ }
+ }
+
+ for (ctlMode = 0; ctlMode < numCtlModes; ctlMode++) {
+ bool isHt40CtlMode =
+ (pCtlMode[ctlMode] == CTL_5GHT40)
+ || (pCtlMode[ctlMode] == CTL_2GHT40);
+ if (isHt40CtlMode)
+ freq = centers.synth_center;
+ else if (pCtlMode[ctlMode] & EXT_ADDITIVE)
+ freq = centers.ext_center;
+ else
+ freq = centers.ctl_center;
+
+ if (ar5416_get_eep_ver(ahp) == 14
+ && ar5416_get_eep_rev(ahp) <= 2)
+ twiceMaxEdgePower = AR5416_MAX_RATE_POWER;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ "LOOP-Mode ctlMode %d < %d, isHt40CtlMode %d, "
+ "EXT_ADDITIVE %d\n",
+ ctlMode, numCtlModes, isHt40CtlMode,
+ (pCtlMode[ctlMode] & EXT_ADDITIVE));
+
+ for (i = 0; (i < AR5416_NUM_CTLS) && pEepData->ctlIndex[i];
+ i++) {
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ " LOOP-Ctlidx %d: cfgCtl 0x%2.2x "
+ "pCtlMode 0x%2.2x ctlIndex 0x%2.2x "
+ "chan %d\n",
+ i, cfgCtl, pCtlMode[ctlMode],
+ pEepData->ctlIndex[i], chan->channel);
+
+ if ((((cfgCtl & ~CTL_MODE_M) |
+ (pCtlMode[ctlMode] & CTL_MODE_M)) ==
+ pEepData->ctlIndex[i])
+ ||
+ (((cfgCtl & ~CTL_MODE_M) |
+ (pCtlMode[ctlMode] & CTL_MODE_M)) ==
+ ((pEepData->
+ ctlIndex[i] & CTL_MODE_M) | SD_NO_CTL))) {
+ rep = &(pEepData->ctlData[i]);
+
+ twiceMinEdgePower =
+ ath9k_hw_get_max_edge_power(freq,
+ rep->
+ ctlEdges
+ [ar5416_get_ntxchains
+ (tx_chainmask)
+ - 1],
+ IS_CHAN_2GHZ
+ (chan));
+
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ " MATCH-EE_IDX %d: ch %d is2 %d "
+ "2xMinEdge %d chainmask %d chains %d\n",
+ i, freq, IS_CHAN_2GHZ(chan),
+ twiceMinEdgePower, tx_chainmask,
+ ar5416_get_ntxchains
+ (tx_chainmask));
+ if ((cfgCtl & ~CTL_MODE_M) == SD_NO_CTL) {
+ twiceMaxEdgePower =
+ min(twiceMaxEdgePower,
+ twiceMinEdgePower);
+ } else {
+ twiceMaxEdgePower =
+ twiceMinEdgePower;
+ break;
+ }
+ }
+ }
+
+ minCtlPower = min(twiceMaxEdgePower, scaledPower);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ " SEL-Min ctlMode %d pCtlMode %d "
+ "2xMaxEdge %d sP %d minCtlPwr %d\n",
+ ctlMode, pCtlMode[ctlMode], twiceMaxEdgePower,
+ scaledPower, minCtlPower);
+
+ switch (pCtlMode[ctlMode]) {
+ case CTL_11B:
+ for (i = 0; i < ARRAY_SIZE(targetPowerCck.tPow2x);
+ i++) {
+ targetPowerCck.tPow2x[i] =
+ min(targetPowerCck.tPow2x[i],
+ minCtlPower);
+ }
+ break;
+ case CTL_11A:
+ case CTL_11G:
+ for (i = 0; i < ARRAY_SIZE(targetPowerOfdm.tPow2x);
+ i++) {
+ targetPowerOfdm.tPow2x[i] =
+ min(targetPowerOfdm.tPow2x[i],
+ minCtlPower);
+ }
+ break;
+ case CTL_5GHT20:
+ case CTL_2GHT20:
+ for (i = 0; i < ARRAY_SIZE(targetPowerHt20.tPow2x);
+ i++) {
+ targetPowerHt20.tPow2x[i] =
+ min(targetPowerHt20.tPow2x[i],
+ minCtlPower);
+ }
+ break;
+ case CTL_11B_EXT:
+ targetPowerCckExt.tPow2x[0] =
+ min(targetPowerCckExt.tPow2x[0], minCtlPower);
+ break;
+ case CTL_11A_EXT:
+ case CTL_11G_EXT:
+ targetPowerOfdmExt.tPow2x[0] =
+ min(targetPowerOfdmExt.tPow2x[0], minCtlPower);
+ break;
+ case CTL_5GHT40:
+ case CTL_2GHT40:
+ for (i = 0; i < ARRAY_SIZE(targetPowerHt40.tPow2x);
+ i++) {
+ targetPowerHt40.tPow2x[i] =
+ min(targetPowerHt40.tPow2x[i],
+ minCtlPower);
+ }
+ break;
+ default:
+ break;
+ }
+ }
+
+ ratesArray[rate6mb] = ratesArray[rate9mb] = ratesArray[rate12mb] =
+ ratesArray[rate18mb] = ratesArray[rate24mb] =
+ targetPowerOfdm.tPow2x[0];
+ ratesArray[rate36mb] = targetPowerOfdm.tPow2x[1];
+ ratesArray[rate48mb] = targetPowerOfdm.tPow2x[2];
+ ratesArray[rate54mb] = targetPowerOfdm.tPow2x[3];
+ ratesArray[rateXr] = targetPowerOfdm.tPow2x[0];
+
+ for (i = 0; i < ARRAY_SIZE(targetPowerHt20.tPow2x); i++)
+ ratesArray[rateHt20_0 + i] = targetPowerHt20.tPow2x[i];
+
+ if (IS_CHAN_2GHZ(chan)) {
+ ratesArray[rate1l] = targetPowerCck.tPow2x[0];
+ ratesArray[rate2s] = ratesArray[rate2l] =
+ targetPowerCck.tPow2x[1];
+ ratesArray[rate5_5s] = ratesArray[rate5_5l] =
+ targetPowerCck.tPow2x[2];
+ ;
+ ratesArray[rate11s] = ratesArray[rate11l] =
+ targetPowerCck.tPow2x[3];
+ ;
+ }
+ if (IS_CHAN_HT40(chan)) {
+ for (i = 0; i < ARRAY_SIZE(targetPowerHt40.tPow2x); i++) {
+ ratesArray[rateHt40_0 + i] =
+ targetPowerHt40.tPow2x[i];
+ }
+ ratesArray[rateDupOfdm] = targetPowerHt40.tPow2x[0];
+ ratesArray[rateDupCck] = targetPowerHt40.tPow2x[0];
+ ratesArray[rateExtOfdm] = targetPowerOfdmExt.tPow2x[0];
+ if (IS_CHAN_2GHZ(chan)) {
+ ratesArray[rateExtCck] =
+ targetPowerCckExt.tPow2x[0];
+ }
+ }
+ return true;
+}
+
+static int
+ath9k_hw_set_txpower(struct ath_hal *ah,
+ struct ar5416_eeprom *pEepData,
+ struct ath9k_channel *chan,
+ u16 cfgCtl,
+ u8 twiceAntennaReduction,
+ u8 twiceMaxRegulatoryPower,
+ u8 powerLimit)
+{
+ struct modal_eep_header *pModal =
+ &(pEepData->modalHeader[IS_CHAN_2GHZ(chan)]);
+ int16_t ratesArray[Ar5416RateSize];
+ int16_t txPowerIndexOffset = 0;
+ u8 ht40PowerIncForPdadc = 2;
+ int i;
+
+ memset(ratesArray, 0, sizeof(ratesArray));
+
+ if ((pEepData->baseEepHeader.
+ version & AR5416_EEP_VER_MINOR_MASK) >=
+ AR5416_EEP_MINOR_VER_2) {
+ ht40PowerIncForPdadc = pModal->ht40PowerIncForPdadc;
+ }
+
+ if (!ath9k_hw_set_power_per_rate_table(ah, pEepData, chan,
+ &ratesArray[0], cfgCtl,
+ twiceAntennaReduction,
+ twiceMaxRegulatoryPower,
+ powerLimit)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "ath9k_hw_set_txpower: unable to set "
+ "tx power per rate table\n");
+ return -EIO;
+ }
+
+ if (!ath9k_hw_set_power_cal_table
+ (ah, pEepData, chan, &txPowerIndexOffset)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "ath9k_hw_set_txpower: unable to set power table\n");
+ return -EIO;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(ratesArray); i++) {
+ ratesArray[i] =
+ (int16_t) (txPowerIndexOffset + ratesArray[i]);
+ if (ratesArray[i] > AR5416_MAX_RATE_POWER)
+ ratesArray[i] = AR5416_MAX_RATE_POWER;
+ }
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ for (i = 0; i < Ar5416RateSize; i++)
+ ratesArray[i] -= AR5416_PWR_TABLE_OFFSET * 2;
+ }
+
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE1,
+ ATH9K_POW_SM(ratesArray[rate18mb], 24)
+ | ATH9K_POW_SM(ratesArray[rate12mb], 16)
+ | ATH9K_POW_SM(ratesArray[rate9mb], 8)
+ | ATH9K_POW_SM(ratesArray[rate6mb], 0)
+ );
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE2,
+ ATH9K_POW_SM(ratesArray[rate54mb], 24)
+ | ATH9K_POW_SM(ratesArray[rate48mb], 16)
+ | ATH9K_POW_SM(ratesArray[rate36mb], 8)
+ | ATH9K_POW_SM(ratesArray[rate24mb], 0)
+ );
+
+ if (IS_CHAN_2GHZ(chan)) {
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE3,
+ ATH9K_POW_SM(ratesArray[rate2s], 24)
+ | ATH9K_POW_SM(ratesArray[rate2l], 16)
+ | ATH9K_POW_SM(ratesArray[rateXr], 8)
+ | ATH9K_POW_SM(ratesArray[rate1l], 0)
+ );
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE4,
+ ATH9K_POW_SM(ratesArray[rate11s], 24)
+ | ATH9K_POW_SM(ratesArray[rate11l], 16)
+ | ATH9K_POW_SM(ratesArray[rate5_5s], 8)
+ | ATH9K_POW_SM(ratesArray[rate5_5l], 0)
+ );
+ }
+
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE5,
+ ATH9K_POW_SM(ratesArray[rateHt20_3], 24)
+ | ATH9K_POW_SM(ratesArray[rateHt20_2], 16)
+ | ATH9K_POW_SM(ratesArray[rateHt20_1], 8)
+ | ATH9K_POW_SM(ratesArray[rateHt20_0], 0)
+ );
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE6,
+ ATH9K_POW_SM(ratesArray[rateHt20_7], 24)
+ | ATH9K_POW_SM(ratesArray[rateHt20_6], 16)
+ | ATH9K_POW_SM(ratesArray[rateHt20_5], 8)
+ | ATH9K_POW_SM(ratesArray[rateHt20_4], 0)
+ );
+
+ if (IS_CHAN_HT40(chan)) {
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE7,
+ ATH9K_POW_SM(ratesArray[rateHt40_3] +
+ ht40PowerIncForPdadc, 24)
+ | ATH9K_POW_SM(ratesArray[rateHt40_2] +
+ ht40PowerIncForPdadc, 16)
+ | ATH9K_POW_SM(ratesArray[rateHt40_1] +
+ ht40PowerIncForPdadc, 8)
+ | ATH9K_POW_SM(ratesArray[rateHt40_0] +
+ ht40PowerIncForPdadc, 0)
+ );
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE8,
+ ATH9K_POW_SM(ratesArray[rateHt40_7] +
+ ht40PowerIncForPdadc, 24)
+ | ATH9K_POW_SM(ratesArray[rateHt40_6] +
+ ht40PowerIncForPdadc, 16)
+ | ATH9K_POW_SM(ratesArray[rateHt40_5] +
+ ht40PowerIncForPdadc, 8)
+ | ATH9K_POW_SM(ratesArray[rateHt40_4] +
+ ht40PowerIncForPdadc, 0)
+ );
+
+ REG_WRITE(ah, AR_PHY_POWER_TX_RATE9,
+ ATH9K_POW_SM(ratesArray[rateExtOfdm], 24)
+ | ATH9K_POW_SM(ratesArray[rateExtCck], 16)
+ | ATH9K_POW_SM(ratesArray[rateDupOfdm], 8)
+ | ATH9K_POW_SM(ratesArray[rateDupCck], 0)
+ );
+ }
+
+ REG_WRITE(ah, AR_PHY_POWER_TX_SUB,
+ ATH9K_POW_SM(pModal->pwrDecreaseFor3Chain, 6)
+ | ATH9K_POW_SM(pModal->pwrDecreaseFor2Chain, 0)
+ );
+
+ i = rate6mb;
+ if (IS_CHAN_HT40(chan))
+ i = rateHt40_0;
+ else if (IS_CHAN_HT20(chan))
+ i = rateHt20_0;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ ah->ah_maxPowerLevel =
+ ratesArray[i] + AR5416_PWR_TABLE_OFFSET * 2;
+ else
+ ah->ah_maxPowerLevel = ratesArray[i];
+
+ return 0;
+}
+
+static inline void ath9k_hw_get_delta_slope_vals(struct ath_hal *ah,
+ u32 coef_scaled,
+ u32 *coef_mantissa,
+ u32 *coef_exponent)
+{
+ u32 coef_exp, coef_man;
+
+ for (coef_exp = 31; coef_exp > 0; coef_exp--)
+ if ((coef_scaled >> coef_exp) & 0x1)
+ break;
+
+ coef_exp = 14 - (coef_exp - COEF_SCALE_S);
+
+ coef_man = coef_scaled + (1 << (COEF_SCALE_S - coef_exp - 1));
+
+ *coef_mantissa = coef_man >> (COEF_SCALE_S - coef_exp);
+ *coef_exponent = coef_exp - 16;
+}
+
+static void
+ath9k_hw_set_delta_slope(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ u32 coef_scaled, ds_coef_exp, ds_coef_man;
+ u32 clockMhzScaled = 0x64000000;
+ struct chan_centers centers;
+
+ if (IS_CHAN_HALF_RATE(chan))
+ clockMhzScaled = clockMhzScaled >> 1;
+ else if (IS_CHAN_QUARTER_RATE(chan))
+ clockMhzScaled = clockMhzScaled >> 2;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ coef_scaled = clockMhzScaled / centers.synth_center;
+
+ ath9k_hw_get_delta_slope_vals(ah, coef_scaled, &ds_coef_man,
+ &ds_coef_exp);
+
+ REG_RMW_FIELD(ah, AR_PHY_TIMING3,
+ AR_PHY_TIMING3_DSC_MAN, ds_coef_man);
+ REG_RMW_FIELD(ah, AR_PHY_TIMING3,
+ AR_PHY_TIMING3_DSC_EXP, ds_coef_exp);
+
+ coef_scaled = (9 * coef_scaled) / 10;
+
+ ath9k_hw_get_delta_slope_vals(ah, coef_scaled, &ds_coef_man,
+ &ds_coef_exp);
+
+ REG_RMW_FIELD(ah, AR_PHY_HALFGI,
+ AR_PHY_HALFGI_DSC_MAN, ds_coef_man);
+ REG_RMW_FIELD(ah, AR_PHY_HALFGI,
+ AR_PHY_HALFGI_DSC_EXP, ds_coef_exp);
+}
+
+static void ath9k_hw_9280_spur_mitigate(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ int bb_spur = AR_NO_SPUR;
+ int freq;
+ int bin, cur_bin;
+ int bb_spur_off, spur_subchannel_sd;
+ int spur_freq_sd;
+ int spur_delta_phase;
+ int denominator;
+ int upper, lower, cur_vit_mask;
+ int tmp, newVal;
+ int i;
+ int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8,
+ AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60
+ };
+ int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10,
+ AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60
+ };
+ int inc[4] = { 0, 100, 0, 0 };
+ struct chan_centers centers;
+
+ int8_t mask_m[123];
+ int8_t mask_p[123];
+ int8_t mask_amt;
+ int tmp_mask;
+ int cur_bb_spur;
+ bool is2GHz = IS_CHAN_2GHZ(chan);
+
+ memset(&mask_m, 0, sizeof(int8_t) * 123);
+ memset(&mask_p, 0, sizeof(int8_t) * 123);
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ freq = centers.synth_center;
+
+ ah->ah_config.spurmode = SPUR_ENABLE_EEPROM;
+ for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) {
+ cur_bb_spur = ath9k_hw_eeprom_get_spur_chan(ah, i, is2GHz);
+
+ if (is2GHz)
+ cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_2GHZ;
+ else
+ cur_bb_spur = (cur_bb_spur / 10) + AR_BASE_FREQ_5GHZ;
+
+ if (AR_NO_SPUR == cur_bb_spur)
+ break;
+ cur_bb_spur = cur_bb_spur - freq;
+
+ if (IS_CHAN_HT40(chan)) {
+ if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT40) &&
+ (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT40)) {
+ bb_spur = cur_bb_spur;
+ break;
+ }
+ } else if ((cur_bb_spur > -AR_SPUR_FEEQ_BOUND_HT20) &&
+ (cur_bb_spur < AR_SPUR_FEEQ_BOUND_HT20)) {
+ bb_spur = cur_bb_spur;
+ break;
+ }
+ }
+
+ if (AR_NO_SPUR == bb_spur) {
+ REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK,
+ AR_PHY_FORCE_CLKEN_CCK_MRC_MUX);
+ return;
+ } else {
+ REG_CLR_BIT(ah, AR_PHY_FORCE_CLKEN_CCK,
+ AR_PHY_FORCE_CLKEN_CCK_MRC_MUX);
+ }
+
+ bin = bb_spur * 320;
+
+ tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0));
+
+ newVal = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI |
+ AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER |
+ AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK |
+ AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK);
+ REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), newVal);
+
+ newVal = (AR_PHY_SPUR_REG_MASK_RATE_CNTL |
+ AR_PHY_SPUR_REG_ENABLE_MASK_PPM |
+ AR_PHY_SPUR_REG_MASK_RATE_SELECT |
+ AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI |
+ SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH));
+ REG_WRITE(ah, AR_PHY_SPUR_REG, newVal);
+
+ if (IS_CHAN_HT40(chan)) {
+ if (bb_spur < 0) {
+ spur_subchannel_sd = 1;
+ bb_spur_off = bb_spur + 10;
+ } else {
+ spur_subchannel_sd = 0;
+ bb_spur_off = bb_spur - 10;
+ }
+ } else {
+ spur_subchannel_sd = 0;
+ bb_spur_off = bb_spur;
+ }
+
+ if (IS_CHAN_HT40(chan))
+ spur_delta_phase =
+ ((bb_spur * 262144) /
+ 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE;
+ else
+ spur_delta_phase =
+ ((bb_spur * 524288) /
+ 10) & AR_PHY_TIMING11_SPUR_DELTA_PHASE;
+
+ denominator = IS_CHAN_2GHZ(chan) ? 44 : 40;
+ spur_freq_sd = ((bb_spur_off * 2048) / denominator) & 0x3ff;
+
+ newVal = (AR_PHY_TIMING11_USE_SPUR_IN_AGC |
+ SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) |
+ SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE));
+ REG_WRITE(ah, AR_PHY_TIMING11, newVal);
+
+ newVal = spur_subchannel_sd << AR_PHY_SFCORR_SPUR_SUBCHNL_SD_S;
+ REG_WRITE(ah, AR_PHY_SFCORR_EXT, newVal);
+
+ cur_bin = -6000;
+ upper = bin + 100;
+ lower = bin - 100;
+
+ for (i = 0; i < 4; i++) {
+ int pilot_mask = 0;
+ int chan_mask = 0;
+ int bp = 0;
+ for (bp = 0; bp < 30; bp++) {
+ if ((cur_bin > lower) && (cur_bin < upper)) {
+ pilot_mask = pilot_mask | 0x1 << bp;
+ chan_mask = chan_mask | 0x1 << bp;
+ }
+ cur_bin += 100;
+ }
+ cur_bin += inc[i];
+ REG_WRITE(ah, pilot_mask_reg[i], pilot_mask);
+ REG_WRITE(ah, chan_mask_reg[i], chan_mask);
+ }
+
+ cur_vit_mask = 6100;
+ upper = bin + 120;
+ lower = bin - 120;
+
+ for (i = 0; i < 123; i++) {
+ if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) {
+
+ /* workaround for gcc bug #37014 */
+ volatile int tmp = abs(cur_vit_mask - bin);
+
+ if (tmp < 75)
+ mask_amt = 1;
+ else
+ mask_amt = 0;
+ if (cur_vit_mask < 0)
+ mask_m[abs(cur_vit_mask / 100)] = mask_amt;
+ else
+ mask_p[cur_vit_mask / 100] = mask_amt;
+ }
+ cur_vit_mask -= 100;
+ }
+
+ tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28)
+ | (mask_m[48] << 26) | (mask_m[49] << 24)
+ | (mask_m[50] << 22) | (mask_m[51] << 20)
+ | (mask_m[52] << 18) | (mask_m[53] << 16)
+ | (mask_m[54] << 14) | (mask_m[55] << 12)
+ | (mask_m[56] << 10) | (mask_m[57] << 8)
+ | (mask_m[58] << 6) | (mask_m[59] << 4)
+ | (mask_m[60] << 2) | (mask_m[61] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask);
+ REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask);
+
+ tmp_mask = (mask_m[31] << 28)
+ | (mask_m[32] << 26) | (mask_m[33] << 24)
+ | (mask_m[34] << 22) | (mask_m[35] << 20)
+ | (mask_m[36] << 18) | (mask_m[37] << 16)
+ | (mask_m[48] << 14) | (mask_m[39] << 12)
+ | (mask_m[40] << 10) | (mask_m[41] << 8)
+ | (mask_m[42] << 6) | (mask_m[43] << 4)
+ | (mask_m[44] << 2) | (mask_m[45] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask);
+
+ tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28)
+ | (mask_m[18] << 26) | (mask_m[18] << 24)
+ | (mask_m[20] << 22) | (mask_m[20] << 20)
+ | (mask_m[22] << 18) | (mask_m[22] << 16)
+ | (mask_m[24] << 14) | (mask_m[24] << 12)
+ | (mask_m[25] << 10) | (mask_m[26] << 8)
+ | (mask_m[27] << 6) | (mask_m[28] << 4)
+ | (mask_m[29] << 2) | (mask_m[30] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask);
+
+ tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28)
+ | (mask_m[2] << 26) | (mask_m[3] << 24)
+ | (mask_m[4] << 22) | (mask_m[5] << 20)
+ | (mask_m[6] << 18) | (mask_m[7] << 16)
+ | (mask_m[8] << 14) | (mask_m[9] << 12)
+ | (mask_m[10] << 10) | (mask_m[11] << 8)
+ | (mask_m[12] << 6) | (mask_m[13] << 4)
+ | (mask_m[14] << 2) | (mask_m[15] << 0);
+ REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask);
+
+ tmp_mask = (mask_p[15] << 28)
+ | (mask_p[14] << 26) | (mask_p[13] << 24)
+ | (mask_p[12] << 22) | (mask_p[11] << 20)
+ | (mask_p[10] << 18) | (mask_p[9] << 16)
+ | (mask_p[8] << 14) | (mask_p[7] << 12)
+ | (mask_p[6] << 10) | (mask_p[5] << 8)
+ | (mask_p[4] << 6) | (mask_p[3] << 4)
+ | (mask_p[2] << 2) | (mask_p[1] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask);
+
+ tmp_mask = (mask_p[30] << 28)
+ | (mask_p[29] << 26) | (mask_p[28] << 24)
+ | (mask_p[27] << 22) | (mask_p[26] << 20)
+ | (mask_p[25] << 18) | (mask_p[24] << 16)
+ | (mask_p[23] << 14) | (mask_p[22] << 12)
+ | (mask_p[21] << 10) | (mask_p[20] << 8)
+ | (mask_p[19] << 6) | (mask_p[18] << 4)
+ | (mask_p[17] << 2) | (mask_p[16] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask);
+
+ tmp_mask = (mask_p[45] << 28)
+ | (mask_p[44] << 26) | (mask_p[43] << 24)
+ | (mask_p[42] << 22) | (mask_p[41] << 20)
+ | (mask_p[40] << 18) | (mask_p[39] << 16)
+ | (mask_p[38] << 14) | (mask_p[37] << 12)
+ | (mask_p[36] << 10) | (mask_p[35] << 8)
+ | (mask_p[34] << 6) | (mask_p[33] << 4)
+ | (mask_p[32] << 2) | (mask_p[31] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask);
+
+ tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28)
+ | (mask_p[59] << 26) | (mask_p[58] << 24)
+ | (mask_p[57] << 22) | (mask_p[56] << 20)
+ | (mask_p[55] << 18) | (mask_p[54] << 16)
+ | (mask_p[53] << 14) | (mask_p[52] << 12)
+ | (mask_p[51] << 10) | (mask_p[50] << 8)
+ | (mask_p[49] << 6) | (mask_p[48] << 4)
+ | (mask_p[47] << 2) | (mask_p[46] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask);
+}
+
+static void ath9k_hw_spur_mitigate(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ int bb_spur = AR_NO_SPUR;
+ int bin, cur_bin;
+ int spur_freq_sd;
+ int spur_delta_phase;
+ int denominator;
+ int upper, lower, cur_vit_mask;
+ int tmp, new;
+ int i;
+ int pilot_mask_reg[4] = { AR_PHY_TIMING7, AR_PHY_TIMING8,
+ AR_PHY_PILOT_MASK_01_30, AR_PHY_PILOT_MASK_31_60
+ };
+ int chan_mask_reg[4] = { AR_PHY_TIMING9, AR_PHY_TIMING10,
+ AR_PHY_CHANNEL_MASK_01_30, AR_PHY_CHANNEL_MASK_31_60
+ };
+ int inc[4] = { 0, 100, 0, 0 };
+
+ int8_t mask_m[123];
+ int8_t mask_p[123];
+ int8_t mask_amt;
+ int tmp_mask;
+ int cur_bb_spur;
+ bool is2GHz = IS_CHAN_2GHZ(chan);
+
+ memset(&mask_m, 0, sizeof(int8_t) * 123);
+ memset(&mask_p, 0, sizeof(int8_t) * 123);
+
+ for (i = 0; i < AR_EEPROM_MODAL_SPURS; i++) {
+ cur_bb_spur = ath9k_hw_eeprom_get_spur_chan(ah, i, is2GHz);
+ if (AR_NO_SPUR == cur_bb_spur)
+ break;
+ cur_bb_spur = cur_bb_spur - (chan->channel * 10);
+ if ((cur_bb_spur > -95) && (cur_bb_spur < 95)) {
+ bb_spur = cur_bb_spur;
+ break;
+ }
+ }
+
+ if (AR_NO_SPUR == bb_spur)
+ return;
+
+ bin = bb_spur * 32;
+
+ tmp = REG_READ(ah, AR_PHY_TIMING_CTRL4(0));
+ new = tmp | (AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI |
+ AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER |
+ AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK |
+ AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK);
+
+ REG_WRITE(ah, AR_PHY_TIMING_CTRL4(0), new);
+
+ new = (AR_PHY_SPUR_REG_MASK_RATE_CNTL |
+ AR_PHY_SPUR_REG_ENABLE_MASK_PPM |
+ AR_PHY_SPUR_REG_MASK_RATE_SELECT |
+ AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI |
+ SM(SPUR_RSSI_THRESH, AR_PHY_SPUR_REG_SPUR_RSSI_THRESH));
+ REG_WRITE(ah, AR_PHY_SPUR_REG, new);
+
+ spur_delta_phase = ((bb_spur * 524288) / 100) &
+ AR_PHY_TIMING11_SPUR_DELTA_PHASE;
+
+ denominator = IS_CHAN_2GHZ(chan) ? 440 : 400;
+ spur_freq_sd = ((bb_spur * 2048) / denominator) & 0x3ff;
+
+ new = (AR_PHY_TIMING11_USE_SPUR_IN_AGC |
+ SM(spur_freq_sd, AR_PHY_TIMING11_SPUR_FREQ_SD) |
+ SM(spur_delta_phase, AR_PHY_TIMING11_SPUR_DELTA_PHASE));
+ REG_WRITE(ah, AR_PHY_TIMING11, new);
+
+ cur_bin = -6000;
+ upper = bin + 100;
+ lower = bin - 100;
+
+ for (i = 0; i < 4; i++) {
+ int pilot_mask = 0;
+ int chan_mask = 0;
+ int bp = 0;
+ for (bp = 0; bp < 30; bp++) {
+ if ((cur_bin > lower) && (cur_bin < upper)) {
+ pilot_mask = pilot_mask | 0x1 << bp;
+ chan_mask = chan_mask | 0x1 << bp;
+ }
+ cur_bin += 100;
+ }
+ cur_bin += inc[i];
+ REG_WRITE(ah, pilot_mask_reg[i], pilot_mask);
+ REG_WRITE(ah, chan_mask_reg[i], chan_mask);
+ }
+
+ cur_vit_mask = 6100;
+ upper = bin + 120;
+ lower = bin - 120;
+
+ for (i = 0; i < 123; i++) {
+ if ((cur_vit_mask > lower) && (cur_vit_mask < upper)) {
+ if ((abs(cur_vit_mask - bin)) < 75)
+ mask_amt = 1;
+ else
+ mask_amt = 0;
+ if (cur_vit_mask < 0)
+ mask_m[abs(cur_vit_mask / 100)] = mask_amt;
+ else
+ mask_p[cur_vit_mask / 100] = mask_amt;
+ }
+ cur_vit_mask -= 100;
+ }
+
+ tmp_mask = (mask_m[46] << 30) | (mask_m[47] << 28)
+ | (mask_m[48] << 26) | (mask_m[49] << 24)
+ | (mask_m[50] << 22) | (mask_m[51] << 20)
+ | (mask_m[52] << 18) | (mask_m[53] << 16)
+ | (mask_m[54] << 14) | (mask_m[55] << 12)
+ | (mask_m[56] << 10) | (mask_m[57] << 8)
+ | (mask_m[58] << 6) | (mask_m[59] << 4)
+ | (mask_m[60] << 2) | (mask_m[61] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_1, tmp_mask);
+ REG_WRITE(ah, AR_PHY_VIT_MASK2_M_46_61, tmp_mask);
+
+ tmp_mask = (mask_m[31] << 28)
+ | (mask_m[32] << 26) | (mask_m[33] << 24)
+ | (mask_m[34] << 22) | (mask_m[35] << 20)
+ | (mask_m[36] << 18) | (mask_m[37] << 16)
+ | (mask_m[48] << 14) | (mask_m[39] << 12)
+ | (mask_m[40] << 10) | (mask_m[41] << 8)
+ | (mask_m[42] << 6) | (mask_m[43] << 4)
+ | (mask_m[44] << 2) | (mask_m[45] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_2, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_31_45, tmp_mask);
+
+ tmp_mask = (mask_m[16] << 30) | (mask_m[16] << 28)
+ | (mask_m[18] << 26) | (mask_m[18] << 24)
+ | (mask_m[20] << 22) | (mask_m[20] << 20)
+ | (mask_m[22] << 18) | (mask_m[22] << 16)
+ | (mask_m[24] << 14) | (mask_m[24] << 12)
+ | (mask_m[25] << 10) | (mask_m[26] << 8)
+ | (mask_m[27] << 6) | (mask_m[28] << 4)
+ | (mask_m[29] << 2) | (mask_m[30] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK_3, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_16_30, tmp_mask);
+
+ tmp_mask = (mask_m[0] << 30) | (mask_m[1] << 28)
+ | (mask_m[2] << 26) | (mask_m[3] << 24)
+ | (mask_m[4] << 22) | (mask_m[5] << 20)
+ | (mask_m[6] << 18) | (mask_m[7] << 16)
+ | (mask_m[8] << 14) | (mask_m[9] << 12)
+ | (mask_m[10] << 10) | (mask_m[11] << 8)
+ | (mask_m[12] << 6) | (mask_m[13] << 4)
+ | (mask_m[14] << 2) | (mask_m[15] << 0);
+ REG_WRITE(ah, AR_PHY_MASK_CTL, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_M_00_15, tmp_mask);
+
+ tmp_mask = (mask_p[15] << 28)
+ | (mask_p[14] << 26) | (mask_p[13] << 24)
+ | (mask_p[12] << 22) | (mask_p[11] << 20)
+ | (mask_p[10] << 18) | (mask_p[9] << 16)
+ | (mask_p[8] << 14) | (mask_p[7] << 12)
+ | (mask_p[6] << 10) | (mask_p[5] << 8)
+ | (mask_p[4] << 6) | (mask_p[3] << 4)
+ | (mask_p[2] << 2) | (mask_p[1] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_1, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_15_01, tmp_mask);
+
+ tmp_mask = (mask_p[30] << 28)
+ | (mask_p[29] << 26) | (mask_p[28] << 24)
+ | (mask_p[27] << 22) | (mask_p[26] << 20)
+ | (mask_p[25] << 18) | (mask_p[24] << 16)
+ | (mask_p[23] << 14) | (mask_p[22] << 12)
+ | (mask_p[21] << 10) | (mask_p[20] << 8)
+ | (mask_p[19] << 6) | (mask_p[18] << 4)
+ | (mask_p[17] << 2) | (mask_p[16] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_2, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_30_16, tmp_mask);
+
+ tmp_mask = (mask_p[45] << 28)
+ | (mask_p[44] << 26) | (mask_p[43] << 24)
+ | (mask_p[42] << 22) | (mask_p[41] << 20)
+ | (mask_p[40] << 18) | (mask_p[39] << 16)
+ | (mask_p[38] << 14) | (mask_p[37] << 12)
+ | (mask_p[36] << 10) | (mask_p[35] << 8)
+ | (mask_p[34] << 6) | (mask_p[33] << 4)
+ | (mask_p[32] << 2) | (mask_p[31] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_3, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_45_31, tmp_mask);
+
+ tmp_mask = (mask_p[61] << 30) | (mask_p[60] << 28)
+ | (mask_p[59] << 26) | (mask_p[58] << 24)
+ | (mask_p[57] << 22) | (mask_p[56] << 20)
+ | (mask_p[55] << 18) | (mask_p[54] << 16)
+ | (mask_p[53] << 14) | (mask_p[52] << 12)
+ | (mask_p[51] << 10) | (mask_p[50] << 8)
+ | (mask_p[49] << 6) | (mask_p[48] << 4)
+ | (mask_p[47] << 2) | (mask_p[46] << 0);
+ REG_WRITE(ah, AR_PHY_BIN_MASK2_4, tmp_mask);
+ REG_WRITE(ah, AR_PHY_MASK2_P_61_45, tmp_mask);
+}
+
+static inline void ath9k_hw_init_chain_masks(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int rx_chainmask, tx_chainmask;
+
+ rx_chainmask = ahp->ah_rxchainmask;
+ tx_chainmask = ahp->ah_txchainmask;
+
+ switch (rx_chainmask) {
+ case 0x5:
+ REG_SET_BIT(ah, AR_PHY_ANALOG_SWAP,
+ AR_PHY_SWAP_ALT_CHAIN);
+ case 0x3:
+ if (((ah)->ah_macVersion <= AR_SREV_VERSION_9160)) {
+ REG_WRITE(ah, AR_PHY_RX_CHAINMASK, 0x7);
+ REG_WRITE(ah, AR_PHY_CAL_CHAINMASK, 0x7);
+ break;
+ }
+ case 0x1:
+ case 0x2:
+ if (!AR_SREV_9280(ah))
+ break;
+ case 0x7:
+ REG_WRITE(ah, AR_PHY_RX_CHAINMASK, rx_chainmask);
+ REG_WRITE(ah, AR_PHY_CAL_CHAINMASK, rx_chainmask);
+ break;
+ default:
+ break;
+ }
+
+ REG_WRITE(ah, AR_SELFGEN_MASK, tx_chainmask);
+ if (tx_chainmask == 0x5) {
+ REG_SET_BIT(ah, AR_PHY_ANALOG_SWAP,
+ AR_PHY_SWAP_ALT_CHAIN);
+ }
+ if (AR_SREV_9100(ah))
+ REG_WRITE(ah, AR_PHY_ANALOG_SWAP,
+ REG_READ(ah, AR_PHY_ANALOG_SWAP) | 0x00000001);
+}
+
+static void ath9k_hw_set_addac(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct modal_eep_header *pModal;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ar5416_eeprom *eep = &ahp->ah_eeprom;
+ u8 biaslevel;
+
+ if (ah->ah_macVersion != AR_SREV_VERSION_9160)
+ return;
+
+ if (ar5416_get_eep_rev(ahp) < AR5416_EEP_MINOR_VER_7)
+ return;
+
+ pModal = &(eep->modalHeader[IS_CHAN_2GHZ(chan)]);
+
+ if (pModal->xpaBiasLvl != 0xff) {
+ biaslevel = pModal->xpaBiasLvl;
+ } else {
+
+ u16 resetFreqBin, freqBin, freqCount = 0;
+ struct chan_centers centers;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+
+ resetFreqBin =
+ FREQ2FBIN(centers.synth_center, IS_CHAN_2GHZ(chan));
+ freqBin = pModal->xpaBiasLvlFreq[0] & 0xff;
+ biaslevel = (u8) (pModal->xpaBiasLvlFreq[0] >> 14);
+
+ freqCount++;
+
+ while (freqCount < 3) {
+ if (pModal->xpaBiasLvlFreq[freqCount] == 0x0)
+ break;
+
+ freqBin = pModal->xpaBiasLvlFreq[freqCount] & 0xff;
+ if (resetFreqBin >= freqBin) {
+ biaslevel =
+ (u8) (pModal->
+ xpaBiasLvlFreq[freqCount]
+ >> 14);
+ } else {
+ break;
+ }
+ freqCount++;
+ }
+ }
+
+ if (IS_CHAN_2GHZ(chan)) {
+ INI_RA(&ahp->ah_iniAddac, 7, 1) =
+ (INI_RA(&ahp->ah_iniAddac, 7, 1) & (~0x18)) | biaslevel
+ << 3;
+ } else {
+ INI_RA(&ahp->ah_iniAddac, 6, 1) =
+ (INI_RA(&ahp->ah_iniAddac, 6, 1) & (~0xc0)) | biaslevel
+ << 6;
+ }
+}
+
+static u32 ath9k_hw_mac_usec(struct ath_hal *ah, u32 clks)
+{
+ if (ah->ah_curchan != NULL)
+ return clks /
+ CLOCK_RATE[ath9k_hw_chan2wmode(ah, ah->ah_curchan)];
+ else
+ return clks / CLOCK_RATE[ATH9K_MODE_11B];
+}
+
+static u32 ath9k_hw_mac_to_usec(struct ath_hal *ah, u32 clks)
+{
+ struct ath9k_channel *chan = ah->ah_curchan;
+
+ if (chan && IS_CHAN_HT40(chan))
+ return ath9k_hw_mac_usec(ah, clks) / 2;
+ else
+ return ath9k_hw_mac_usec(ah, clks);
+}
+
+static u32 ath9k_hw_mac_clks(struct ath_hal *ah, u32 usecs)
+{
+ if (ah->ah_curchan != NULL)
+ return usecs * CLOCK_RATE[ath9k_hw_chan2wmode(ah,
+ ah->ah_curchan)];
+ else
+ return usecs * CLOCK_RATE[ATH9K_MODE_11B];
+}
+
+static u32 ath9k_hw_mac_to_clks(struct ath_hal *ah, u32 usecs)
+{
+ struct ath9k_channel *chan = ah->ah_curchan;
+
+ if (chan && IS_CHAN_HT40(chan))
+ return ath9k_hw_mac_clks(ah, usecs) * 2;
+ else
+ return ath9k_hw_mac_clks(ah, usecs);
+}
+
+static bool ath9k_hw_set_ack_timeout(struct ath_hal *ah, u32 us)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (us > ath9k_hw_mac_to_usec(ah, MS(0xffffffff, AR_TIME_OUT_ACK))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: bad ack timeout %u\n",
+ __func__, us);
+ ahp->ah_acktimeout = (u32) -1;
+ return false;
+ } else {
+ REG_RMW_FIELD(ah, AR_TIME_OUT,
+ AR_TIME_OUT_ACK, ath9k_hw_mac_to_clks(ah, us));
+ ahp->ah_acktimeout = us;
+ return true;
+ }
+}
+
+static bool ath9k_hw_set_cts_timeout(struct ath_hal *ah, u32 us)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (us > ath9k_hw_mac_to_usec(ah, MS(0xffffffff, AR_TIME_OUT_CTS))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: bad cts timeout %u\n",
+ __func__, us);
+ ahp->ah_ctstimeout = (u32) -1;
+ return false;
+ } else {
+ REG_RMW_FIELD(ah, AR_TIME_OUT,
+ AR_TIME_OUT_CTS, ath9k_hw_mac_to_clks(ah, us));
+ ahp->ah_ctstimeout = us;
+ return true;
+ }
+}
+static bool ath9k_hw_set_global_txtimeout(struct ath_hal *ah,
+ u32 tu)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (tu > 0xFFFF) {
+ DPRINTF(ah->ah_sc, ATH_DBG_XMIT,
+ "%s: bad global tx timeout %u\n", __func__, tu);
+ ahp->ah_globaltxtimeout = (u32) -1;
+ return false;
+ } else {
+ REG_RMW_FIELD(ah, AR_GTXTO, AR_GTXTO_TIMEOUT_LIMIT, tu);
+ ahp->ah_globaltxtimeout = tu;
+ return true;
+ }
+}
+
+bool ath9k_hw_setslottime(struct ath_hal *ah, u32 us)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (us < ATH9K_SLOT_TIME_9 || us > ath9k_hw_mac_to_usec(ah, 0xffff)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: bad slot time %u\n",
+ __func__, us);
+ ahp->ah_slottime = (u32) -1;
+ return false;
+ } else {
+ REG_WRITE(ah, AR_D_GBL_IFS_SLOT, ath9k_hw_mac_to_clks(ah, us));
+ ahp->ah_slottime = us;
+ return true;
+ }
+}
+
+static inline void ath9k_hw_init_user_settings(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "--AP %s ahp->ah_miscMode 0x%x\n",
+ __func__, ahp->ah_miscMode);
+ if (ahp->ah_miscMode != 0)
+ REG_WRITE(ah, AR_PCU_MISC,
+ REG_READ(ah, AR_PCU_MISC) | ahp->ah_miscMode);
+ if (ahp->ah_slottime != (u32) -1)
+ ath9k_hw_setslottime(ah, ahp->ah_slottime);
+ if (ahp->ah_acktimeout != (u32) -1)
+ ath9k_hw_set_ack_timeout(ah, ahp->ah_acktimeout);
+ if (ahp->ah_ctstimeout != (u32) -1)
+ ath9k_hw_set_cts_timeout(ah, ahp->ah_ctstimeout);
+ if (ahp->ah_globaltxtimeout != (u32) -1)
+ ath9k_hw_set_global_txtimeout(ah, ahp->ah_globaltxtimeout);
+}
+
+static inline int
+ath9k_hw_process_ini(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ enum ath9k_ht_macmode macmode)
+{
+ int i, regWrites = 0;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 modesIndex, freqIndex;
+ int status;
+
+ switch (chan->chanmode) {
+ case CHANNEL_A:
+ case CHANNEL_A_HT20:
+ modesIndex = 1;
+ freqIndex = 1;
+ break;
+ case CHANNEL_A_HT40PLUS:
+ case CHANNEL_A_HT40MINUS:
+ modesIndex = 2;
+ freqIndex = 1;
+ break;
+ case CHANNEL_G:
+ case CHANNEL_G_HT20:
+ case CHANNEL_B:
+ modesIndex = 4;
+ freqIndex = 2;
+ break;
+ case CHANNEL_G_HT40PLUS:
+ case CHANNEL_G_HT40MINUS:
+ modesIndex = 3;
+ freqIndex = 2;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ REG_WRITE(ah, AR_PHY(0), 0x00000007);
+
+ REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_EXTERNAL_RADIO);
+
+ ath9k_hw_set_addac(ah, chan);
+
+ if (AR_SREV_5416_V22_OR_LATER(ah)) {
+ REG_WRITE_ARRAY(&ahp->ah_iniAddac, 1, regWrites);
+ } else {
+ struct ar5416IniArray temp;
+ u32 addacSize =
+ sizeof(u32) * ahp->ah_iniAddac.ia_rows *
+ ahp->ah_iniAddac.ia_columns;
+
+ memcpy(ahp->ah_addac5416_21,
+ ahp->ah_iniAddac.ia_array, addacSize);
+
+ (ahp->ah_addac5416_21)[31 *
+ ahp->ah_iniAddac.ia_columns + 1] = 0;
+
+ temp.ia_array = ahp->ah_addac5416_21;
+ temp.ia_columns = ahp->ah_iniAddac.ia_columns;
+ temp.ia_rows = ahp->ah_iniAddac.ia_rows;
+ REG_WRITE_ARRAY(&temp, 1, regWrites);
+ }
+ REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
+
+ for (i = 0; i < ahp->ah_iniModes.ia_rows; i++) {
+ u32 reg = INI_RA(&ahp->ah_iniModes, i, 0);
+ u32 val = INI_RA(&ahp->ah_iniModes, i, modesIndex);
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ if (ah->ah_devid == AR9280_DEVID_PCI)
+ val = ath9k_hw_ini_fixup(ah, &ahp->ah_eeprom, reg,
+ val);
+#endif
+
+ REG_WRITE(ah, reg, val);
+
+ if (reg >= 0x7800 && reg < 0x78a0
+ && ah->ah_config.analog_shiftreg) {
+ udelay(100);
+ }
+
+ DO_DELAY(regWrites);
+ }
+
+ for (i = 0; i < ahp->ah_iniCommon.ia_rows; i++) {
+ u32 reg = INI_RA(&ahp->ah_iniCommon, i, 0);
+ u32 val = INI_RA(&ahp->ah_iniCommon, i, 1);
+
+ REG_WRITE(ah, reg, val);
+
+ if (reg >= 0x7800 && reg < 0x78a0
+ && ah->ah_config.analog_shiftreg) {
+ udelay(100);
+ }
+
+ DO_DELAY(regWrites);
+ }
+
+ ath9k_hw_write_regs(ah, modesIndex, freqIndex, regWrites);
+
+ if (AR_SREV_9280_20(ah) && IS_CHAN_A_5MHZ_SPACED(chan)) {
+ REG_WRITE_ARRAY(&ahp->ah_iniModesAdditional, modesIndex,
+ regWrites);
+ }
+
+ ath9k_hw_override_ini(ah, chan);
+ ath9k_hw_set_regs(ah, chan, macmode);
+ ath9k_hw_init_chain_masks(ah);
+
+ status = ath9k_hw_set_txpower(ah, &ahp->ah_eeprom, chan,
+ ath9k_regd_get_ctl(ah, chan),
+ ath9k_regd_get_antenna_allowed(ah,
+ chan),
+ chan->maxRegTxPower * 2,
+ min((u32) MAX_RATE_POWER,
+ (u32) ah->ah_powerLimit));
+ if (status != 0) {
+ DPRINTF(ah->ah_sc, ATH_DBG_POWER_MGMT,
+ "%s: error init'ing transmit power\n", __func__);
+ return -EIO;
+ }
+
+ if (!ath9k_hw_set_rf_regs(ah, chan, freqIndex)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REG_IO,
+ "%s: ar5416SetRfRegs failed\n", __func__);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static inline void ath9k_hw_setup_calibration(struct ath_hal *ah,
+ struct hal_cal_list *currCal)
+{
+ REG_RMW_FIELD(ah, AR_PHY_TIMING_CTRL4(0),
+ AR_PHY_TIMING_CTRL4_IQCAL_LOG_COUNT_MAX,
+ currCal->calData->calCountMax);
+
+ switch (currCal->calData->calType) {
+ case IQ_MISMATCH_CAL:
+ REG_WRITE(ah, AR_PHY_CALMODE, AR_PHY_CALMODE_IQ);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: starting IQ Mismatch Calibration\n",
+ __func__);
+ break;
+ case ADC_GAIN_CAL:
+ REG_WRITE(ah, AR_PHY_CALMODE, AR_PHY_CALMODE_ADC_GAIN);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: starting ADC Gain Calibration\n", __func__);
+ break;
+ case ADC_DC_CAL:
+ REG_WRITE(ah, AR_PHY_CALMODE, AR_PHY_CALMODE_ADC_DC_PER);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: starting ADC DC Calibration\n", __func__);
+ break;
+ case ADC_DC_INIT_CAL:
+ REG_WRITE(ah, AR_PHY_CALMODE, AR_PHY_CALMODE_ADC_DC_INIT);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: starting Init ADC DC Calibration\n",
+ __func__);
+ break;
+ }
+
+ REG_SET_BIT(ah, AR_PHY_TIMING_CTRL4(0),
+ AR_PHY_TIMING_CTRL4_DO_CAL);
+}
+
+static inline void ath9k_hw_reset_calibration(struct ath_hal *ah,
+ struct hal_cal_list *currCal)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ ath9k_hw_setup_calibration(ah, currCal);
+
+ currCal->calState = CAL_RUNNING;
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ ahp->ah_Meas0.sign[i] = 0;
+ ahp->ah_Meas1.sign[i] = 0;
+ ahp->ah_Meas2.sign[i] = 0;
+ ahp->ah_Meas3.sign[i] = 0;
+ }
+
+ ahp->ah_CalSamples = 0;
+}
+
+static inline void
+ath9k_hw_per_calibration(struct ath_hal *ah,
+ struct ath9k_channel *ichan,
+ u8 rxchainmask,
+ struct hal_cal_list *currCal,
+ bool *isCalDone)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ *isCalDone = false;
+
+ if (currCal->calState == CAL_RUNNING) {
+ if (!(REG_READ(ah,
+ AR_PHY_TIMING_CTRL4(0)) &
+ AR_PHY_TIMING_CTRL4_DO_CAL)) {
+
+ currCal->calData->calCollect(ah);
+
+ ahp->ah_CalSamples++;
+
+ if (ahp->ah_CalSamples >=
+ currCal->calData->calNumSamples) {
+ int i, numChains = 0;
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ if (rxchainmask & (1 << i))
+ numChains++;
+ }
+
+ currCal->calData->calPostProc(ah,
+ numChains);
+
+ ichan->CalValid |=
+ currCal->calData->calType;
+ currCal->calState = CAL_DONE;
+ *isCalDone = true;
+ } else {
+ ath9k_hw_setup_calibration(ah, currCal);
+ }
+ }
+ } else if (!(ichan->CalValid & currCal->calData->calType)) {
+ ath9k_hw_reset_calibration(ah, currCal);
+ }
+}
+
+static inline bool ath9k_hw_run_init_cals(struct ath_hal *ah,
+ int init_cal_count)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel ichan;
+ bool isCalDone;
+ struct hal_cal_list *currCal = ahp->ah_cal_list_curr;
+ const struct hal_percal_data *calData = currCal->calData;
+ int i;
+
+ if (currCal == NULL)
+ return false;
+
+ ichan.CalValid = 0;
+
+ for (i = 0; i < init_cal_count; i++) {
+ ath9k_hw_reset_calibration(ah, currCal);
+
+ if (!ath9k_hw_wait(ah, AR_PHY_TIMING_CTRL4(0),
+ AR_PHY_TIMING_CTRL4_DO_CAL, 0)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: Cal %d failed to complete in 100ms.\n",
+ __func__, calData->calType);
+
+ ahp->ah_cal_list = ahp->ah_cal_list_last =
+ ahp->ah_cal_list_curr = NULL;
+ return false;
+ }
+
+ ath9k_hw_per_calibration(ah, &ichan, ahp->ah_rxchainmask,
+ currCal, &isCalDone);
+ if (!isCalDone) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: Not able to run Init Cal %d.\n",
+ __func__, calData->calType);
+ }
+ if (currCal->calNext) {
+ currCal = currCal->calNext;
+ calData = currCal->calData;
+ }
+ }
+
+ ahp->ah_cal_list = ahp->ah_cal_list_last = ahp->ah_cal_list_curr = NULL;
+ return true;
+}
+
+static inline bool
+ath9k_hw_channel_change(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ enum ath9k_ht_macmode macmode)
+{
+ u32 synthDelay, qnum;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ for (qnum = 0; qnum < AR_NUM_QCU; qnum++) {
+ if (ath9k_hw_numtxpending(ah, qnum)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: Transmit frames pending on queue %d\n",
+ __func__, qnum);
+ return false;
+ }
+ }
+
+ REG_WRITE(ah, AR_PHY_RFBUS_REQ, AR_PHY_RFBUS_REQ_EN);
+ if (!ath9k_hw_wait(ah, AR_PHY_RFBUS_GRANT, AR_PHY_RFBUS_GRANT_EN,
+ AR_PHY_RFBUS_GRANT_EN)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_PHY_IO,
+ "%s: Could not kill baseband RX\n", __func__);
+ return false;
+ }
+
+ ath9k_hw_set_regs(ah, chan, macmode);
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ if (!(ath9k_hw_ar9280_set_channel(ah, chan))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: failed to set channel\n", __func__);
+ return false;
+ }
+ } else {
+ if (!(ath9k_hw_set_channel(ah, chan))) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: failed to set channel\n", __func__);
+ return false;
+ }
+ }
+
+ if (ath9k_hw_set_txpower(ah, &ahp->ah_eeprom, chan,
+ ath9k_regd_get_ctl(ah, chan),
+ ath9k_regd_get_antenna_allowed(ah, chan),
+ chan->maxRegTxPower * 2,
+ min((u32) MAX_RATE_POWER,
+ (u32) ah->ah_powerLimit)) != 0) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: error init'ing transmit power\n", __func__);
+ return false;
+ }
+
+ synthDelay = REG_READ(ah, AR_PHY_RX_DELAY) & AR_PHY_RX_DELAY_DELAY;
+ if (IS_CHAN_CCK(chan))
+ synthDelay = (4 * synthDelay) / 22;
+ else
+ synthDelay /= 10;
+
+ udelay(synthDelay + BASE_ACTIVATE_DELAY);
+
+ REG_WRITE(ah, AR_PHY_RFBUS_REQ, 0);
+
+ if (IS_CHAN_OFDM(chan) || IS_CHAN_HT(chan))
+ ath9k_hw_set_delta_slope(ah, chan);
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ ath9k_hw_9280_spur_mitigate(ah, chan);
+ else
+ ath9k_hw_spur_mitigate(ah, chan);
+
+ if (!chan->oneTimeCalsDone)
+ chan->oneTimeCalsDone = true;
+
+ return true;
+}
+
+static bool ath9k_hw_chip_reset(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_WARM))
+ return false;
+
+ if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
+ return false;
+
+ ahp->ah_chipFullSleep = false;
+
+ ath9k_hw_init_pll(ah, chan);
+
+ ath9k_hw_set_rfmode(ah, chan);
+
+ return true;
+}
+
+static inline void ath9k_hw_set_dma(struct ath_hal *ah)
+{
+ u32 regval;
+
+ regval = REG_READ(ah, AR_AHB_MODE);
+ REG_WRITE(ah, AR_AHB_MODE, regval | AR_AHB_PREFETCH_RD_EN);
+
+ regval = REG_READ(ah, AR_TXCFG) & ~AR_TXCFG_DMASZ_MASK;
+ REG_WRITE(ah, AR_TXCFG, regval | AR_TXCFG_DMASZ_128B);
+
+ REG_RMW_FIELD(ah, AR_TXCFG, AR_FTRIG, ah->ah_txTrigLevel);
+
+ regval = REG_READ(ah, AR_RXCFG) & ~AR_RXCFG_DMASZ_MASK;
+ REG_WRITE(ah, AR_RXCFG, regval | AR_RXCFG_DMASZ_128B);
+
+ REG_WRITE(ah, AR_RXFIFO_CFG, 0x200);
+
+ if (AR_SREV_9285(ah)) {
+ REG_WRITE(ah, AR_PCU_TXBUF_CTRL,
+ AR_9285_PCU_TXBUF_CTRL_USABLE_SIZE);
+ } else {
+ REG_WRITE(ah, AR_PCU_TXBUF_CTRL,
+ AR_PCU_TXBUF_CTRL_USABLE_SIZE);
+ }
+}
+
+bool ath9k_hw_stopdmarecv(struct ath_hal *ah)
+{
+ REG_WRITE(ah, AR_CR, AR_CR_RXD);
+ if (!ath9k_hw_wait(ah, AR_CR, AR_CR_RXE, 0)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: dma failed to stop in 10ms\n"
+ "AR_CR=0x%08x\nAR_DIAG_SW=0x%08x\n",
+ __func__,
+ REG_READ(ah, AR_CR), REG_READ(ah, AR_DIAG_SW));
+ return false;
+ } else {
+ return true;
+ }
+}
+
+void ath9k_hw_startpcureceive(struct ath_hal *ah)
+{
+ REG_CLR_BIT(ah, AR_DIAG_SW,
+ (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
+
+ ath9k_enable_mib_counters(ah);
+
+ ath9k_ani_reset(ah);
+}
+
+void ath9k_hw_stoppcurecv(struct ath_hal *ah)
+{
+ REG_SET_BIT(ah, AR_DIAG_SW, AR_DIAG_RX_DIS);
+
+ ath9k_hw_disable_mib_counters(ah);
+}
+
+static bool ath9k_hw_iscal_supported(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ enum hal_cal_types calType)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ bool retval = false;
+
+ switch (calType & ahp->ah_suppCals) {
+ case IQ_MISMATCH_CAL:
+ if (!IS_CHAN_B(chan))
+ retval = true;
+ break;
+ case ADC_GAIN_CAL:
+ case ADC_DC_CAL:
+ if (!IS_CHAN_B(chan)
+ && !(IS_CHAN_2GHZ(chan) && IS_CHAN_HT20(chan)))
+ retval = true;
+ break;
+ }
+
+ return retval;
+}
+
+static inline bool ath9k_hw_init_cal(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *ichan =
+ ath9k_regd_check_channel(ah, chan);
+
+ REG_WRITE(ah, AR_PHY_AGC_CONTROL,
+ REG_READ(ah, AR_PHY_AGC_CONTROL) |
+ AR_PHY_AGC_CONTROL_CAL);
+
+ if (!ath9k_hw_wait
+ (ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: offset calibration failed to complete in 1ms; "
+ "noisy environment?\n", __func__);
+ return false;
+ }
+
+ REG_WRITE(ah, AR_PHY_AGC_CONTROL,
+ REG_READ(ah, AR_PHY_AGC_CONTROL) |
+ AR_PHY_AGC_CONTROL_NF);
+
+ ahp->ah_cal_list = ahp->ah_cal_list_last = ahp->ah_cal_list_curr =
+ NULL;
+
+ if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah)) {
+ if (ath9k_hw_iscal_supported(ah, chan, ADC_GAIN_CAL)) {
+ INIT_CAL(&ahp->ah_adcGainCalData);
+ INSERT_CAL(ahp, &ahp->ah_adcGainCalData);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: enabling ADC Gain Calibration.\n",
+ __func__);
+ }
+ if (ath9k_hw_iscal_supported(ah, chan, ADC_DC_CAL)) {
+ INIT_CAL(&ahp->ah_adcDcCalData);
+ INSERT_CAL(ahp, &ahp->ah_adcDcCalData);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: enabling ADC DC Calibration.\n",
+ __func__);
+ }
+ if (ath9k_hw_iscal_supported(ah, chan, IQ_MISMATCH_CAL)) {
+ INIT_CAL(&ahp->ah_iqCalData);
+ INSERT_CAL(ahp, &ahp->ah_iqCalData);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: enabling IQ Calibration.\n",
+ __func__);
+ }
+
+ ahp->ah_cal_list_curr = ahp->ah_cal_list;
+
+ if (ahp->ah_cal_list_curr)
+ ath9k_hw_reset_calibration(ah,
+ ahp->ah_cal_list_curr);
+ }
+
+ ichan->CalValid = 0;
+
+ return true;
+}
+
+
+bool ath9k_hw_reset(struct ath_hal *ah, enum ath9k_opmode opmode,
+ struct ath9k_channel *chan,
+ enum ath9k_ht_macmode macmode,
+ u8 txchainmask, u8 rxchainmask,
+ enum ath9k_ht_extprotspacing extprotspacing,
+ bool bChannelChange,
+ int *status)
+{
+#define FAIL(_code) do { ecode = _code; goto bad; } while (0)
+ u32 saveLedState;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *curchan = ah->ah_curchan;
+ u32 saveDefAntenna;
+ u32 macStaId1;
+ int ecode;
+ int i, rx_chainmask;
+
+ ahp->ah_extprotspacing = extprotspacing;
+ ahp->ah_txchainmask = txchainmask;
+ ahp->ah_rxchainmask = rxchainmask;
+
+ if (AR_SREV_9280(ah)) {
+ ahp->ah_txchainmask &= 0x3;
+ ahp->ah_rxchainmask &= 0x3;
+ }
+
+ if (ath9k_hw_check_chan(ah, chan) == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u/0x%x; no mapping\n",
+ __func__, chan->channel, chan->channelFlags);
+ FAIL(-EINVAL);
+ }
+
+ if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
+ return false;
+
+ if (curchan)
+ ath9k_hw_getnf(ah, curchan);
+
+ if (bChannelChange &&
+ (ahp->ah_chipFullSleep != true) &&
+ (ah->ah_curchan != NULL) &&
+ (chan->channel != ah->ah_curchan->channel) &&
+ ((chan->channelFlags & CHANNEL_ALL) ==
+ (ah->ah_curchan->channelFlags & CHANNEL_ALL)) &&
+ (!AR_SREV_9280(ah) || (!IS_CHAN_A_5MHZ_SPACED(chan) &&
+ !IS_CHAN_A_5MHZ_SPACED(ah->
+ ah_curchan)))) {
+
+ if (ath9k_hw_channel_change(ah, chan, macmode)) {
+ ath9k_hw_loadnf(ah, ah->ah_curchan);
+ ath9k_hw_start_nfcal(ah);
+ return true;
+ }
+ }
+
+ saveDefAntenna = REG_READ(ah, AR_DEF_ANTENNA);
+ if (saveDefAntenna == 0)
+ saveDefAntenna = 1;
+
+ macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B;
+
+ saveLedState = REG_READ(ah, AR_CFG_LED) &
+ (AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL |
+ AR_CFG_LED_BLINK_THRESH_SEL | AR_CFG_LED_BLINK_SLOW);
+
+ ath9k_hw_mark_phy_inactive(ah);
+
+ if (!ath9k_hw_chip_reset(ah, chan)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET, "%s: chip reset failed\n",
+ __func__);
+ FAIL(-EIO);
+ }
+
+ if (AR_SREV_9280(ah)) {
+ REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL,
+ AR_GPIO_JTAG_DISABLE);
+
+ if (test_bit(ATH9K_MODE_11A, ah->ah_caps.wireless_modes)) {
+ if (IS_CHAN_5GHZ(chan))
+ ath9k_hw_set_gpio(ah, 9, 0);
+ else
+ ath9k_hw_set_gpio(ah, 9, 1);
+ }
+ ath9k_hw_cfg_output(ah, 9, ATH9K_GPIO_OUTPUT_MUX_AS_OUTPUT);
+ }
+
+ ecode = ath9k_hw_process_ini(ah, chan, macmode);
+ if (ecode != 0)
+ goto bad;
+
+ if (IS_CHAN_OFDM(chan) || IS_CHAN_HT(chan))
+ ath9k_hw_set_delta_slope(ah, chan);
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ ath9k_hw_9280_spur_mitigate(ah, chan);
+ else
+ ath9k_hw_spur_mitigate(ah, chan);
+
+ if (!ath9k_hw_eeprom_set_board_values(ah, chan)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
+ "%s: error setting board options\n", __func__);
+ FAIL(-EIO);
+ }
+
+ ath9k_hw_decrease_chain_power(ah, chan);
+
+ REG_WRITE(ah, AR_STA_ID0, get_unaligned_le32(ahp->ah_macaddr));
+ REG_WRITE(ah, AR_STA_ID1, get_unaligned_le16(ahp->ah_macaddr + 4)
+ | macStaId1
+ | AR_STA_ID1_RTS_USE_DEF
+ | (ah->ah_config.
+ ack_6mb ? AR_STA_ID1_ACKCTS_6MB : 0)
+ | ahp->ah_staId1Defaults);
+ ath9k_hw_set_operating_mode(ah, opmode);
+
+ REG_WRITE(ah, AR_BSSMSKL, get_unaligned_le32(ahp->ah_bssidmask));
+ REG_WRITE(ah, AR_BSSMSKU, get_unaligned_le16(ahp->ah_bssidmask + 4));
+
+ REG_WRITE(ah, AR_DEF_ANTENNA, saveDefAntenna);
+
+ REG_WRITE(ah, AR_BSS_ID0, get_unaligned_le32(ahp->ah_bssid));
+ REG_WRITE(ah, AR_BSS_ID1, get_unaligned_le16(ahp->ah_bssid + 4) |
+ ((ahp->ah_assocId & 0x3fff) << AR_BSS_ID1_AID_S));
+
+ REG_WRITE(ah, AR_ISR, ~0);
+
+ REG_WRITE(ah, AR_RSSI_THR, INIT_RSSI_THR);
+
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ if (!(ath9k_hw_ar9280_set_channel(ah, chan)))
+ FAIL(-EIO);
+ } else {
+ if (!(ath9k_hw_set_channel(ah, chan)))
+ FAIL(-EIO);
+ }
+
+ for (i = 0; i < AR_NUM_DCU; i++)
+ REG_WRITE(ah, AR_DQCUMASK(i), 1 << i);
+
+ ahp->ah_intrTxqs = 0;
+ for (i = 0; i < ah->ah_caps.total_queues; i++)
+ ath9k_hw_resettxqueue(ah, i);
+
+ ath9k_hw_init_interrupt_masks(ah, opmode);
+ ath9k_hw_init_qos(ah);
+
+ ath9k_hw_init_user_settings(ah);
+
+ ah->ah_opmode = opmode;
+
+ REG_WRITE(ah, AR_STA_ID1,
+ REG_READ(ah, AR_STA_ID1) | AR_STA_ID1_PRESERVE_SEQNUM);
+
+ ath9k_hw_set_dma(ah);
+
+ REG_WRITE(ah, AR_OBS, 8);
+
+ if (ahp->ah_intrMitigation) {
+
+ REG_RMW_FIELD(ah, AR_RIMT, AR_RIMT_LAST, 500);
+ REG_RMW_FIELD(ah, AR_RIMT, AR_RIMT_FIRST, 2000);
+ }
+
+ ath9k_hw_init_bb(ah, chan);
+
+ if (!ath9k_hw_init_cal(ah, chan))
+ FAIL(-ENODEV);
+
+ rx_chainmask = ahp->ah_rxchainmask;
+ if ((rx_chainmask == 0x5) || (rx_chainmask == 0x3)) {
+ REG_WRITE(ah, AR_PHY_RX_CHAINMASK, rx_chainmask);
+ REG_WRITE(ah, AR_PHY_CAL_CHAINMASK, rx_chainmask);
+ }
+
+ REG_WRITE(ah, AR_CFG_LED, saveLedState | AR_CFG_SCLK_32KHZ);
+
+ if (AR_SREV_9100(ah)) {
+ u32 mask;
+ mask = REG_READ(ah, AR_CFG);
+ if (mask & (AR_CFG_SWRB | AR_CFG_SWTB | AR_CFG_SWRG)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s CFG Byte Swap Set 0x%x\n", __func__,
+ mask);
+ } else {
+ mask =
+ INIT_CONFIG_STATUS | AR_CFG_SWRB | AR_CFG_SWTB;
+ REG_WRITE(ah, AR_CFG, mask);
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s Setting CFG 0x%x\n", __func__,
+ REG_READ(ah, AR_CFG));
+ }
+ } else {
+#ifdef __BIG_ENDIAN
+ REG_WRITE(ah, AR_CFG, AR_CFG_SWTD | AR_CFG_SWRD);
+#endif
+ }
+
+ return true;
+bad:
+ if (status)
+ *status = ecode;
+ return false;
+#undef FAIL
+}
+
+bool ath9k_hw_phy_disable(struct ath_hal *ah)
+{
+ return ath9k_hw_set_reset_reg(ah, ATH9K_RESET_WARM);
+}
+
+bool ath9k_hw_disable(struct ath_hal *ah)
+{
+ if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
+ return false;
+
+ return ath9k_hw_set_reset_reg(ah, ATH9K_RESET_COLD);
+}
+
+bool
+ath9k_hw_calibrate(struct ath_hal *ah, struct ath9k_channel *chan,
+ u8 rxchainmask, bool longcal,
+ bool *isCalDone)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct hal_cal_list *currCal = ahp->ah_cal_list_curr;
+ struct ath9k_channel *ichan =
+ ath9k_regd_check_channel(ah, chan);
+
+ *isCalDone = true;
+
+ if (ichan == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u/0x%x; no mapping\n",
+ __func__, chan->channel, chan->channelFlags);
+ return false;
+ }
+
+ if (currCal &&
+ (currCal->calState == CAL_RUNNING ||
+ currCal->calState == CAL_WAITING)) {
+ ath9k_hw_per_calibration(ah, ichan, rxchainmask, currCal,
+ isCalDone);
+ if (*isCalDone) {
+ ahp->ah_cal_list_curr = currCal = currCal->calNext;
+
+ if (currCal->calState == CAL_WAITING) {
+ *isCalDone = false;
+ ath9k_hw_reset_calibration(ah, currCal);
+ }
+ }
+ }
+
+ if (longcal) {
+ ath9k_hw_getnf(ah, ichan);
+ ath9k_hw_loadnf(ah, ah->ah_curchan);
+ ath9k_hw_start_nfcal(ah);
+
+ if ((ichan->channelFlags & CHANNEL_CW_INT) != 0) {
+
+ chan->channelFlags |= CHANNEL_CW_INT;
+ ichan->channelFlags &= ~CHANNEL_CW_INT;
+ }
+ }
+
+ return true;
+}
+
+static void ath9k_hw_iqcal_collect(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ ahp->ah_totalPowerMeasI[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_0(i));
+ ahp->ah_totalPowerMeasQ[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_1(i));
+ ahp->ah_totalIqCorrMeas[i] +=
+ (int32_t) REG_READ(ah, AR_PHY_CAL_MEAS_2(i));
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%d: Chn %d pmi=0x%08x;pmq=0x%08x;iqcm=0x%08x;\n",
+ ahp->ah_CalSamples, i, ahp->ah_totalPowerMeasI[i],
+ ahp->ah_totalPowerMeasQ[i],
+ ahp->ah_totalIqCorrMeas[i]);
+ }
+}
+
+static void ath9k_hw_adc_gaincal_collect(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ ahp->ah_totalAdcIOddPhase[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_0(i));
+ ahp->ah_totalAdcIEvenPhase[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_1(i));
+ ahp->ah_totalAdcQOddPhase[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_2(i));
+ ahp->ah_totalAdcQEvenPhase[i] +=
+ REG_READ(ah, AR_PHY_CAL_MEAS_3(i));
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%d: Chn %d oddi=0x%08x; eveni=0x%08x; "
+ "oddq=0x%08x; evenq=0x%08x;\n",
+ ahp->ah_CalSamples, i,
+ ahp->ah_totalAdcIOddPhase[i],
+ ahp->ah_totalAdcIEvenPhase[i],
+ ahp->ah_totalAdcQOddPhase[i],
+ ahp->ah_totalAdcQEvenPhase[i]);
+ }
+}
+
+static void ath9k_hw_adc_dccal_collect(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int i;
+
+ for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+ ahp->ah_totalAdcDcOffsetIOddPhase[i] +=
+ (int32_t) REG_READ(ah, AR_PHY_CAL_MEAS_0(i));
+ ahp->ah_totalAdcDcOffsetIEvenPhase[i] +=
+ (int32_t) REG_READ(ah, AR_PHY_CAL_MEAS_1(i));
+ ahp->ah_totalAdcDcOffsetQOddPhase[i] +=
+ (int32_t) REG_READ(ah, AR_PHY_CAL_MEAS_2(i));
+ ahp->ah_totalAdcDcOffsetQEvenPhase[i] +=
+ (int32_t) REG_READ(ah, AR_PHY_CAL_MEAS_3(i));
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%d: Chn %d oddi=0x%08x; eveni=0x%08x; "
+ "oddq=0x%08x; evenq=0x%08x;\n",
+ ahp->ah_CalSamples, i,
+ ahp->ah_totalAdcDcOffsetIOddPhase[i],
+ ahp->ah_totalAdcDcOffsetIEvenPhase[i],
+ ahp->ah_totalAdcDcOffsetQOddPhase[i],
+ ahp->ah_totalAdcDcOffsetQEvenPhase[i]);
+ }
+}
+
+static void ath9k_hw_iqcalibrate(struct ath_hal *ah, u8 numChains)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 powerMeasQ, powerMeasI, iqCorrMeas;
+ u32 qCoffDenom, iCoffDenom;
+ int32_t qCoff, iCoff;
+ int iqCorrNeg, i;
+
+ for (i = 0; i < numChains; i++) {
+ powerMeasI = ahp->ah_totalPowerMeasI[i];
+ powerMeasQ = ahp->ah_totalPowerMeasQ[i];
+ iqCorrMeas = ahp->ah_totalIqCorrMeas[i];
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Starting IQ Cal and Correction for Chain %d\n",
+ i);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Orignal: Chn %diq_corr_meas = 0x%08x\n",
+ i, ahp->ah_totalIqCorrMeas[i]);
+
+ iqCorrNeg = 0;
+
+
+ if (iqCorrMeas > 0x80000000) {
+ iqCorrMeas = (0xffffffff - iqCorrMeas) + 1;
+ iqCorrNeg = 1;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_i = 0x%08x\n", i, powerMeasI);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_q = 0x%08x\n", i, powerMeasQ);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE, "iqCorrNeg is 0x%08x\n",
+ iqCorrNeg);
+
+ iCoffDenom = (powerMeasI / 2 + powerMeasQ / 2) / 128;
+ qCoffDenom = powerMeasQ / 64;
+
+ if (powerMeasQ != 0) {
+
+ iCoff = iqCorrMeas / iCoffDenom;
+ qCoff = powerMeasI / qCoffDenom - 64;
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d iCoff = 0x%08x\n", i, iCoff);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d qCoff = 0x%08x\n", i, qCoff);
+
+
+ iCoff = iCoff & 0x3f;
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "New: Chn %d iCoff = 0x%08x\n", i, iCoff);
+ if (iqCorrNeg == 0x0)
+ iCoff = 0x40 - iCoff;
+
+ if (qCoff > 15)
+ qCoff = 15;
+ else if (qCoff <= -16)
+ qCoff = 16;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d : iCoff = 0x%x qCoff = 0x%x\n",
+ i, iCoff, qCoff);
+
+ REG_RMW_FIELD(ah, AR_PHY_TIMING_CTRL4(i),
+ AR_PHY_TIMING_CTRL4_IQCORR_Q_I_COFF,
+ iCoff);
+ REG_RMW_FIELD(ah, AR_PHY_TIMING_CTRL4(i),
+ AR_PHY_TIMING_CTRL4_IQCORR_Q_Q_COFF,
+ qCoff);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "IQ Cal and Correction done for Chain %d\n",
+ i);
+ }
+ }
+
+ REG_SET_BIT(ah, AR_PHY_TIMING_CTRL4(0),
+ AR_PHY_TIMING_CTRL4_IQCORR_ENABLE);
+}
+
+static void
+ath9k_hw_adc_gaincal_calibrate(struct ath_hal *ah, u8 numChains)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 iOddMeasOffset, iEvenMeasOffset, qOddMeasOffset,
+ qEvenMeasOffset;
+ u32 qGainMismatch, iGainMismatch, val, i;
+
+ for (i = 0; i < numChains; i++) {
+ iOddMeasOffset = ahp->ah_totalAdcIOddPhase[i];
+ iEvenMeasOffset = ahp->ah_totalAdcIEvenPhase[i];
+ qOddMeasOffset = ahp->ah_totalAdcQOddPhase[i];
+ qEvenMeasOffset = ahp->ah_totalAdcQEvenPhase[i];
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Starting ADC Gain Cal for Chain %d\n", i);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_odd_i = 0x%08x\n", i,
+ iOddMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_even_i = 0x%08x\n", i,
+ iEvenMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_odd_q = 0x%08x\n", i,
+ qOddMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_even_q = 0x%08x\n", i,
+ qEvenMeasOffset);
+
+ if (iOddMeasOffset != 0 && qEvenMeasOffset != 0) {
+ iGainMismatch =
+ ((iEvenMeasOffset * 32) /
+ iOddMeasOffset) & 0x3f;
+ qGainMismatch =
+ ((qOddMeasOffset * 32) /
+ qEvenMeasOffset) & 0x3f;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d gain_mismatch_i = 0x%08x\n", i,
+ iGainMismatch);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d gain_mismatch_q = 0x%08x\n", i,
+ qGainMismatch);
+
+ val = REG_READ(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(i));
+ val &= 0xfffff000;
+ val |= (qGainMismatch) | (iGainMismatch << 6);
+ REG_WRITE(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(i), val);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "ADC Gain Cal done for Chain %d\n", i);
+ }
+ }
+
+ REG_WRITE(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(0),
+ REG_READ(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(0)) |
+ AR_PHY_NEW_ADC_GAIN_CORR_ENABLE);
+}
+
+static void
+ath9k_hw_adc_dccal_calibrate(struct ath_hal *ah, u8 numChains)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 iOddMeasOffset, iEvenMeasOffset, val, i;
+ int32_t qOddMeasOffset, qEvenMeasOffset, qDcMismatch, iDcMismatch;
+ const struct hal_percal_data *calData =
+ ahp->ah_cal_list_curr->calData;
+ u32 numSamples =
+ (1 << (calData->calCountMax + 5)) * calData->calNumSamples;
+
+ for (i = 0; i < numChains; i++) {
+ iOddMeasOffset = ahp->ah_totalAdcDcOffsetIOddPhase[i];
+ iEvenMeasOffset = ahp->ah_totalAdcDcOffsetIEvenPhase[i];
+ qOddMeasOffset = ahp->ah_totalAdcDcOffsetQOddPhase[i];
+ qEvenMeasOffset = ahp->ah_totalAdcDcOffsetQEvenPhase[i];
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Starting ADC DC Offset Cal for Chain %d\n", i);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_odd_i = %d\n", i,
+ iOddMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_even_i = %d\n", i,
+ iEvenMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_odd_q = %d\n", i,
+ qOddMeasOffset);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d pwr_meas_even_q = %d\n", i,
+ qEvenMeasOffset);
+
+ iDcMismatch = (((iEvenMeasOffset - iOddMeasOffset) * 2) /
+ numSamples) & 0x1ff;
+ qDcMismatch = (((qOddMeasOffset - qEvenMeasOffset) * 2) /
+ numSamples) & 0x1ff;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d dc_offset_mismatch_i = 0x%08x\n", i,
+ iDcMismatch);
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "Chn %d dc_offset_mismatch_q = 0x%08x\n", i,
+ qDcMismatch);
+
+ val = REG_READ(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(i));
+ val &= 0xc0000fff;
+ val |= (qDcMismatch << 12) | (iDcMismatch << 21);
+ REG_WRITE(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(i), val);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "ADC DC Offset Cal done for Chain %d\n", i);
+ }
+
+ REG_WRITE(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(0),
+ REG_READ(ah, AR_PHY_NEW_ADC_DC_GAIN_CORR(0)) |
+ AR_PHY_NEW_ADC_DC_OFFSET_CORR_ENABLE);
+}
+
+bool ath9k_hw_set_txpowerlimit(struct ath_hal *ah, u32 limit)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *chan = ah->ah_curchan;
+
+ ah->ah_powerLimit = min(limit, (u32) MAX_RATE_POWER);
+
+ if (ath9k_hw_set_txpower(ah, &ahp->ah_eeprom, chan,
+ ath9k_regd_get_ctl(ah, chan),
+ ath9k_regd_get_antenna_allowed(ah,
+ chan),
+ chan->maxRegTxPower * 2,
+ min((u32) MAX_RATE_POWER,
+ (u32) ah->ah_powerLimit)) != 0)
+ return false;
+
+ return true;
+}
+
+void
+ath9k_hw_get_channel_centers(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ struct chan_centers *centers)
+{
+ int8_t extoff;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (!IS_CHAN_HT40(chan)) {
+ centers->ctl_center = centers->ext_center =
+ centers->synth_center = chan->channel;
+ return;
+ }
+
+ if ((chan->chanmode == CHANNEL_A_HT40PLUS) ||
+ (chan->chanmode == CHANNEL_G_HT40PLUS)) {
+ centers->synth_center =
+ chan->channel + HT40_CHANNEL_CENTER_SHIFT;
+ extoff = 1;
+ } else {
+ centers->synth_center =
+ chan->channel - HT40_CHANNEL_CENTER_SHIFT;
+ extoff = -1;
+ }
+
+ centers->ctl_center = centers->synth_center - (extoff *
+ HT40_CHANNEL_CENTER_SHIFT);
+ centers->ext_center = centers->synth_center + (extoff *
+ ((ahp->
+ ah_extprotspacing
+ ==
+ ATH9K_HT_EXTPROTSPACING_20)
+ ?
+ HT40_CHANNEL_CENTER_SHIFT
+ : 15));
+
+}
+
+void
+ath9k_hw_reset_calvalid(struct ath_hal *ah, struct ath9k_channel *chan,
+ bool *isCalDone)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *ichan =
+ ath9k_regd_check_channel(ah, chan);
+ struct hal_cal_list *currCal = ahp->ah_cal_list_curr;
+
+ *isCalDone = true;
+
+ if (!AR_SREV_9100(ah) && !AR_SREV_9160_10_OR_LATER(ah))
+ return;
+
+ if (currCal == NULL)
+ return;
+
+ if (ichan == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: invalid channel %u/0x%x; no mapping\n",
+ __func__, chan->channel, chan->channelFlags);
+ return;
+ }
+
+
+ if (currCal->calState != CAL_DONE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: Calibration state incorrect, %d\n",
+ __func__, currCal->calState);
+ return;
+ }
+
+
+ if (!ath9k_hw_iscal_supported(ah, chan, currCal->calData->calType))
+ return;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_CALIBRATE,
+ "%s: Resetting Cal %d state for channel %u/0x%x\n",
+ __func__, currCal->calData->calType, chan->channel,
+ chan->channelFlags);
+
+ ichan->CalValid &= ~currCal->calData->calType;
+ currCal->calState = CAL_WAITING;
+
+ *isCalDone = false;
+}
+
+void ath9k_hw_getmac(struct ath_hal *ah, u8 *mac)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ memcpy(mac, ahp->ah_macaddr, ETH_ALEN);
+}
+
+bool ath9k_hw_setmac(struct ath_hal *ah, const u8 *mac)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ memcpy(ahp->ah_macaddr, mac, ETH_ALEN);
+ return true;
+}
+
+void ath9k_hw_getbssidmask(struct ath_hal *ah, u8 *mask)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ memcpy(mask, ahp->ah_bssidmask, ETH_ALEN);
+}
+
+bool
+ath9k_hw_setbssidmask(struct ath_hal *ah, const u8 *mask)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ memcpy(ahp->ah_bssidmask, mask, ETH_ALEN);
+
+ REG_WRITE(ah, AR_BSSMSKL, get_unaligned_le32(ahp->ah_bssidmask));
+ REG_WRITE(ah, AR_BSSMSKU, get_unaligned_le16(ahp->ah_bssidmask + 4));
+
+ return true;
+}
+
+#ifdef CONFIG_ATH9K_RFKILL
+static void ath9k_enable_rfkill(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL,
+ AR_GPIO_INPUT_EN_VAL_RFSILENT_BB);
+
+ REG_CLR_BIT(ah, AR_GPIO_INPUT_MUX2,
+ AR_GPIO_INPUT_MUX2_RFSILENT);
+
+ ath9k_hw_cfg_gpio_input(ah, ahp->ah_gpioSelect);
+ REG_SET_BIT(ah, AR_PHY_TEST, RFSILENT_BB);
+
+ if (ahp->ah_gpioBit == ath9k_hw_gpio_get(ah, ahp->ah_gpioSelect)) {
+
+ ath9k_hw_set_gpio_intr(ah, ahp->ah_gpioSelect,
+ !ahp->ah_gpioBit);
+ } else {
+ ath9k_hw_set_gpio_intr(ah, ahp->ah_gpioSelect,
+ ahp->ah_gpioBit);
+ }
+}
+#endif
+
+void
+ath9k_hw_write_associd(struct ath_hal *ah, const u8 *bssid,
+ u16 assocId)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ memcpy(ahp->ah_bssid, bssid, ETH_ALEN);
+ ahp->ah_assocId = assocId;
+
+ REG_WRITE(ah, AR_BSS_ID0, get_unaligned_le32(ahp->ah_bssid));
+ REG_WRITE(ah, AR_BSS_ID1, get_unaligned_le16(ahp->ah_bssid + 4) |
+ ((assocId & 0x3fff) << AR_BSS_ID1_AID_S));
+}
+
+u64 ath9k_hw_gettsf64(struct ath_hal *ah)
+{
+ u64 tsf;
+
+ tsf = REG_READ(ah, AR_TSF_U32);
+ tsf = (tsf << 32) | REG_READ(ah, AR_TSF_L32);
+ return tsf;
+}
+
+void ath9k_hw_reset_tsf(struct ath_hal *ah)
+{
+ int count;
+
+ count = 0;
+ while (REG_READ(ah, AR_SLP32_MODE) & AR_SLP32_TSF_WRITE_STATUS) {
+ count++;
+ if (count > 10) {
+ DPRINTF(ah->ah_sc, ATH_DBG_RESET,
+ "%s: AR_SLP32_TSF_WRITE_STATUS limit exceeded\n",
+ __func__);
+ break;
+ }
+ udelay(10);
+ }
+ REG_WRITE(ah, AR_RESET_TSF, AR_RESET_TSF_ONCE);
+}
+
+u32 ath9k_hw_getdefantenna(struct ath_hal *ah)
+{
+ return REG_READ(ah, AR_DEF_ANTENNA) & 0x7;
+}
+
+void ath9k_hw_setantenna(struct ath_hal *ah, u32 antenna)
+{
+ REG_WRITE(ah, AR_DEF_ANTENNA, (antenna & 0x7));
+}
+
+bool
+ath9k_hw_setantennaswitch(struct ath_hal *ah,
+ enum ath9k_ant_setting settings,
+ struct ath9k_channel *chan,
+ u8 *tx_chainmask,
+ u8 *rx_chainmask,
+ u8 *antenna_cfgd)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ static u8 tx_chainmask_cfg, rx_chainmask_cfg;
+
+ if (AR_SREV_9280(ah)) {
+ if (!tx_chainmask_cfg) {
+
+ tx_chainmask_cfg = *tx_chainmask;
+ rx_chainmask_cfg = *rx_chainmask;
+ }
+
+ switch (settings) {
+ case ATH9K_ANT_FIXED_A:
+ *tx_chainmask = ATH9K_ANTENNA0_CHAINMASK;
+ *rx_chainmask = ATH9K_ANTENNA0_CHAINMASK;
+ *antenna_cfgd = true;
+ break;
+ case ATH9K_ANT_FIXED_B:
+ if (ah->ah_caps.tx_chainmask >
+ ATH9K_ANTENNA1_CHAINMASK) {
+ *tx_chainmask = ATH9K_ANTENNA1_CHAINMASK;
+ }
+ *rx_chainmask = ATH9K_ANTENNA1_CHAINMASK;
+ *antenna_cfgd = true;
+ break;
+ case ATH9K_ANT_VARIABLE:
+ *tx_chainmask = tx_chainmask_cfg;
+ *rx_chainmask = rx_chainmask_cfg;
+ *antenna_cfgd = true;
+ break;
+ default:
+ break;
+ }
+ } else {
+ ahp->ah_diversityControl = settings;
+ }
+
+ return true;
+}
+
+void ath9k_hw_setopmode(struct ath_hal *ah)
+{
+ ath9k_hw_set_operating_mode(ah, ah->ah_opmode);
+}
+
+bool
+ath9k_hw_getcapability(struct ath_hal *ah, enum ath9k_capability_type type,
+ u32 capability, u32 *result)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ const struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ switch (type) {
+ case ATH9K_CAP_CIPHER:
+ switch (capability) {
+ case ATH9K_CIPHER_AES_CCM:
+ case ATH9K_CIPHER_AES_OCB:
+ case ATH9K_CIPHER_TKIP:
+ case ATH9K_CIPHER_WEP:
+ case ATH9K_CIPHER_MIC:
+ case ATH9K_CIPHER_CLR:
+ return true;
+ default:
+ return false;
+ }
+ case ATH9K_CAP_TKIP_MIC:
+ switch (capability) {
+ case 0:
+ return true;
+ case 1:
+ return (ahp->ah_staId1Defaults &
+ AR_STA_ID1_CRPT_MIC_ENABLE) ? true :
+ false;
+ }
+ case ATH9K_CAP_TKIP_SPLIT:
+ return (ahp->ah_miscMode & AR_PCU_MIC_NEW_LOC_ENA) ?
+ false : true;
+ case ATH9K_CAP_WME_TKIPMIC:
+ return 0;
+ case ATH9K_CAP_PHYCOUNTERS:
+ return ahp->ah_hasHwPhyCounters ? 0 : -ENXIO;
+ case ATH9K_CAP_DIVERSITY:
+ return (REG_READ(ah, AR_PHY_CCK_DETECT) &
+ AR_PHY_CCK_DETECT_BB_ENABLE_ANT_FAST_DIV) ?
+ true : false;
+ case ATH9K_CAP_PHYDIAG:
+ return true;
+ case ATH9K_CAP_MCAST_KEYSRCH:
+ switch (capability) {
+ case 0:
+ return true;
+ case 1:
+ if (REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_ADHOC) {
+ return false;
+ } else {
+ return (ahp->ah_staId1Defaults &
+ AR_STA_ID1_MCAST_KSRCH) ? true :
+ false;
+ }
+ }
+ return false;
+ case ATH9K_CAP_TSF_ADJUST:
+ return (ahp->ah_miscMode & AR_PCU_TX_ADD_TSF) ?
+ true : false;
+ case ATH9K_CAP_RFSILENT:
+ if (capability == 3)
+ return false;
+ case ATH9K_CAP_ANT_CFG_2GHZ:
+ *result = pCap->num_antcfg_2ghz;
+ return true;
+ case ATH9K_CAP_ANT_CFG_5GHZ:
+ *result = pCap->num_antcfg_5ghz;
+ return true;
+ case ATH9K_CAP_TXPOW:
+ switch (capability) {
+ case 0:
+ return 0;
+ case 1:
+ *result = ah->ah_powerLimit;
+ return 0;
+ case 2:
+ *result = ah->ah_maxPowerLevel;
+ return 0;
+ case 3:
+ *result = ah->ah_tpScale;
+ return 0;
+ }
+ return false;
+ default:
+ return false;
+ }
+}
+
+int
+ath9k_hw_select_antconfig(struct ath_hal *ah, u32 cfg)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_channel *chan = ah->ah_curchan;
+ const struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ u16 ant_config;
+ u32 halNumAntConfig;
+
+ halNumAntConfig =
+ IS_CHAN_2GHZ(chan) ? pCap->num_antcfg_2ghz : pCap->
+ num_antcfg_5ghz;
+
+ if (cfg < halNumAntConfig) {
+ if (!ath9k_hw_get_eeprom_antenna_cfg(ahp, chan,
+ cfg, &ant_config)) {
+ REG_WRITE(ah, AR_PHY_SWITCH_COM, ant_config);
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+bool ath9k_hw_intrpend(struct ath_hal *ah)
+{
+ u32 host_isr;
+
+ if (AR_SREV_9100(ah))
+ return true;
+
+ host_isr = REG_READ(ah, AR_INTR_ASYNC_CAUSE);
+ if ((host_isr & AR_INTR_MAC_IRQ) && (host_isr != AR_INTR_SPURIOUS))
+ return true;
+
+ host_isr = REG_READ(ah, AR_INTR_SYNC_CAUSE);
+ if ((host_isr & AR_INTR_SYNC_DEFAULT)
+ && (host_isr != AR_INTR_SPURIOUS))
+ return true;
+
+ return false;
+}
+
+bool ath9k_hw_getisr(struct ath_hal *ah, enum ath9k_int *masked)
+{
+ u32 isr = 0;
+ u32 mask2 = 0;
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ u32 sync_cause = 0;
+ bool fatal_int = false;
+
+ if (!AR_SREV_9100(ah)) {
+ if (REG_READ(ah, AR_INTR_ASYNC_CAUSE) & AR_INTR_MAC_IRQ) {
+ if ((REG_READ(ah, AR_RTC_STATUS) & AR_RTC_STATUS_M)
+ == AR_RTC_STATUS_ON) {
+ isr = REG_READ(ah, AR_ISR);
+ }
+ }
+
+ sync_cause =
+ REG_READ(ah,
+ AR_INTR_SYNC_CAUSE) & AR_INTR_SYNC_DEFAULT;
+
+ *masked = 0;
+
+ if (!isr && !sync_cause)
+ return false;
+ } else {
+ *masked = 0;
+ isr = REG_READ(ah, AR_ISR);
+ }
+
+ if (isr) {
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (isr & AR_ISR_BCNMISC) {
+ u32 isr2;
+ isr2 = REG_READ(ah, AR_ISR_S2);
+ if (isr2 & AR_ISR_S2_TIM)
+ mask2 |= ATH9K_INT_TIM;
+ if (isr2 & AR_ISR_S2_DTIM)
+ mask2 |= ATH9K_INT_DTIM;
+ if (isr2 & AR_ISR_S2_DTIMSYNC)
+ mask2 |= ATH9K_INT_DTIMSYNC;
+ if (isr2 & (AR_ISR_S2_CABEND))
+ mask2 |= ATH9K_INT_CABEND;
+ if (isr2 & AR_ISR_S2_GTT)
+ mask2 |= ATH9K_INT_GTT;
+ if (isr2 & AR_ISR_S2_CST)
+ mask2 |= ATH9K_INT_CST;
+ }
+
+ isr = REG_READ(ah, AR_ISR_RAC);
+ if (isr == 0xffffffff) {
+ *masked = 0;
+ return false;
+ }
+
+ *masked = isr & ATH9K_INT_COMMON;
+
+ if (ahp->ah_intrMitigation) {
+
+ if (isr & (AR_ISR_RXMINTR | AR_ISR_RXINTM))
+ *masked |= ATH9K_INT_RX;
+ }
+
+ if (isr & (AR_ISR_RXOK | AR_ISR_RXERR))
+ *masked |= ATH9K_INT_RX;
+ if (isr &
+ (AR_ISR_TXOK | AR_ISR_TXDESC | AR_ISR_TXERR |
+ AR_ISR_TXEOL)) {
+ u32 s0_s, s1_s;
+
+ *masked |= ATH9K_INT_TX;
+
+ s0_s = REG_READ(ah, AR_ISR_S0_S);
+ ahp->ah_intrTxqs |= MS(s0_s, AR_ISR_S0_QCU_TXOK);
+ ahp->ah_intrTxqs |= MS(s0_s, AR_ISR_S0_QCU_TXDESC);
+
+ s1_s = REG_READ(ah, AR_ISR_S1_S);
+ ahp->ah_intrTxqs |= MS(s1_s, AR_ISR_S1_QCU_TXERR);
+ ahp->ah_intrTxqs |= MS(s1_s, AR_ISR_S1_QCU_TXEOL);
+ }
+
+ if (isr & AR_ISR_RXORN) {
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT,
+ "%s: receive FIFO overrun interrupt\n",
+ __func__);
+ }
+
+ if (!AR_SREV_9100(ah)) {
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP)) {
+ u32 isr5 = REG_READ(ah, AR_ISR_S5_S);
+ if (isr5 & AR_ISR_S5_TIM_TIMER)
+ *masked |= ATH9K_INT_TIM_TIMER;
+ }
+ }
+
+ *masked |= mask2;
+ }
+ if (AR_SREV_9100(ah))
+ return true;
+ if (sync_cause) {
+ fatal_int =
+ (sync_cause &
+ (AR_INTR_SYNC_HOST1_FATAL | AR_INTR_SYNC_HOST1_PERR))
+ ? true : false;
+
+ if (fatal_int) {
+ if (sync_cause & AR_INTR_SYNC_HOST1_FATAL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "%s: received PCI FATAL interrupt\n",
+ __func__);
+ }
+ if (sync_cause & AR_INTR_SYNC_HOST1_PERR) {
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "%s: received PCI PERR interrupt\n",
+ __func__);
+ }
+ }
+ if (sync_cause & AR_INTR_SYNC_RADM_CPL_TIMEOUT) {
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT,
+ "%s: AR_INTR_SYNC_RADM_CPL_TIMEOUT\n",
+ __func__);
+ REG_WRITE(ah, AR_RC, AR_RC_HOSTIF);
+ REG_WRITE(ah, AR_RC, 0);
+ *masked |= ATH9K_INT_FATAL;
+ }
+ if (sync_cause & AR_INTR_SYNC_LOCAL_TIMEOUT) {
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT,
+ "%s: AR_INTR_SYNC_LOCAL_TIMEOUT\n",
+ __func__);
+ }
+
+ REG_WRITE(ah, AR_INTR_SYNC_CAUSE_CLR, sync_cause);
+ (void) REG_READ(ah, AR_INTR_SYNC_CAUSE_CLR);
+ }
+ return true;
+}
+
+enum ath9k_int ath9k_hw_intrget(struct ath_hal *ah)
+{
+ return AH5416(ah)->ah_maskReg;
+}
+
+enum ath9k_int ath9k_hw_set_interrupts(struct ath_hal *ah, enum ath9k_int ints)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 omask = ahp->ah_maskReg;
+ u32 mask, mask2;
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT, "%s: 0x%x => 0x%x\n", __func__,
+ omask, ints);
+
+ if (omask & ATH9K_INT_GLOBAL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT, "%s: disable IER\n",
+ __func__);
+ REG_WRITE(ah, AR_IER, AR_IER_DISABLE);
+ (void) REG_READ(ah, AR_IER);
+ if (!AR_SREV_9100(ah)) {
+ REG_WRITE(ah, AR_INTR_ASYNC_ENABLE, 0);
+ (void) REG_READ(ah, AR_INTR_ASYNC_ENABLE);
+
+ REG_WRITE(ah, AR_INTR_SYNC_ENABLE, 0);
+ (void) REG_READ(ah, AR_INTR_SYNC_ENABLE);
+ }
+ }
+
+ mask = ints & ATH9K_INT_COMMON;
+ mask2 = 0;
+
+ if (ints & ATH9K_INT_TX) {
+ if (ahp->ah_txOkInterruptMask)
+ mask |= AR_IMR_TXOK;
+ if (ahp->ah_txDescInterruptMask)
+ mask |= AR_IMR_TXDESC;
+ if (ahp->ah_txErrInterruptMask)
+ mask |= AR_IMR_TXERR;
+ if (ahp->ah_txEolInterruptMask)
+ mask |= AR_IMR_TXEOL;
+ }
+ if (ints & ATH9K_INT_RX) {
+ mask |= AR_IMR_RXERR;
+ if (ahp->ah_intrMitigation)
+ mask |= AR_IMR_RXMINTR | AR_IMR_RXINTM;
+ else
+ mask |= AR_IMR_RXOK | AR_IMR_RXDESC;
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP))
+ mask |= AR_IMR_GENTMR;
+ }
+
+ if (ints & (ATH9K_INT_BMISC)) {
+ mask |= AR_IMR_BCNMISC;
+ if (ints & ATH9K_INT_TIM)
+ mask2 |= AR_IMR_S2_TIM;
+ if (ints & ATH9K_INT_DTIM)
+ mask2 |= AR_IMR_S2_DTIM;
+ if (ints & ATH9K_INT_DTIMSYNC)
+ mask2 |= AR_IMR_S2_DTIMSYNC;
+ if (ints & ATH9K_INT_CABEND)
+ mask2 |= (AR_IMR_S2_CABEND);
+ }
+
+ if (ints & (ATH9K_INT_GTT | ATH9K_INT_CST)) {
+ mask |= AR_IMR_BCNMISC;
+ if (ints & ATH9K_INT_GTT)
+ mask2 |= AR_IMR_S2_GTT;
+ if (ints & ATH9K_INT_CST)
+ mask2 |= AR_IMR_S2_CST;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT, "%s: new IMR 0x%x\n", __func__,
+ mask);
+ REG_WRITE(ah, AR_IMR, mask);
+ mask = REG_READ(ah, AR_IMR_S2) & ~(AR_IMR_S2_TIM |
+ AR_IMR_S2_DTIM |
+ AR_IMR_S2_DTIMSYNC |
+ AR_IMR_S2_CABEND |
+ AR_IMR_S2_CABTO |
+ AR_IMR_S2_TSFOOR |
+ AR_IMR_S2_GTT | AR_IMR_S2_CST);
+ REG_WRITE(ah, AR_IMR_S2, mask | mask2);
+ ahp->ah_maskReg = ints;
+
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP)) {
+ if (ints & ATH9K_INT_TIM_TIMER)
+ REG_SET_BIT(ah, AR_IMR_S5, AR_IMR_S5_TIM_TIMER);
+ else
+ REG_CLR_BIT(ah, AR_IMR_S5, AR_IMR_S5_TIM_TIMER);
+ }
+
+ if (ints & ATH9K_INT_GLOBAL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT, "%s: enable IER\n",
+ __func__);
+ REG_WRITE(ah, AR_IER, AR_IER_ENABLE);
+ if (!AR_SREV_9100(ah)) {
+ REG_WRITE(ah, AR_INTR_ASYNC_ENABLE,
+ AR_INTR_MAC_IRQ);
+ REG_WRITE(ah, AR_INTR_ASYNC_MASK, AR_INTR_MAC_IRQ);
+
+
+ REG_WRITE(ah, AR_INTR_SYNC_ENABLE,
+ AR_INTR_SYNC_DEFAULT);
+ REG_WRITE(ah, AR_INTR_SYNC_MASK,
+ AR_INTR_SYNC_DEFAULT);
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT, "AR_IMR 0x%x IER 0x%x\n",
+ REG_READ(ah, AR_IMR), REG_READ(ah, AR_IER));
+ }
+
+ return omask;
+}
+
+void
+ath9k_hw_beaconinit(struct ath_hal *ah,
+ u32 next_beacon, u32 beacon_period)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ int flags = 0;
+
+ ahp->ah_beaconInterval = beacon_period;
+
+ switch (ah->ah_opmode) {
+ case ATH9K_M_STA:
+ case ATH9K_M_MONITOR:
+ REG_WRITE(ah, AR_NEXT_TBTT_TIMER, TU_TO_USEC(next_beacon));
+ REG_WRITE(ah, AR_NEXT_DMA_BEACON_ALERT, 0xffff);
+ REG_WRITE(ah, AR_NEXT_SWBA, 0x7ffff);
+ flags |= AR_TBTT_TIMER_EN;
+ break;
+ case ATH9K_M_IBSS:
+ REG_SET_BIT(ah, AR_TXCFG,
+ AR_TXCFG_ADHOC_BEACON_ATIM_TX_POLICY);
+ REG_WRITE(ah, AR_NEXT_NDP_TIMER,
+ TU_TO_USEC(next_beacon +
+ (ahp->ah_atimWindow ? ahp->
+ ah_atimWindow : 1)));
+ flags |= AR_NDP_TIMER_EN;
+ case ATH9K_M_HOSTAP:
+ REG_WRITE(ah, AR_NEXT_TBTT_TIMER, TU_TO_USEC(next_beacon));
+ REG_WRITE(ah, AR_NEXT_DMA_BEACON_ALERT,
+ TU_TO_USEC(next_beacon -
+ ah->ah_config.
+ dma_beacon_response_time));
+ REG_WRITE(ah, AR_NEXT_SWBA,
+ TU_TO_USEC(next_beacon -
+ ah->ah_config.
+ sw_beacon_response_time));
+ flags |=
+ AR_TBTT_TIMER_EN | AR_DBA_TIMER_EN | AR_SWBA_TIMER_EN;
+ break;
+ }
+
+ REG_WRITE(ah, AR_BEACON_PERIOD, TU_TO_USEC(beacon_period));
+ REG_WRITE(ah, AR_DMA_BEACON_PERIOD, TU_TO_USEC(beacon_period));
+ REG_WRITE(ah, AR_SWBA_PERIOD, TU_TO_USEC(beacon_period));
+ REG_WRITE(ah, AR_NDP_PERIOD, TU_TO_USEC(beacon_period));
+
+ beacon_period &= ~ATH9K_BEACON_ENA;
+ if (beacon_period & ATH9K_BEACON_RESET_TSF) {
+ beacon_period &= ~ATH9K_BEACON_RESET_TSF;
+ ath9k_hw_reset_tsf(ah);
+ }
+
+ REG_SET_BIT(ah, AR_TIMER_MODE, flags);
+}
+
+void
+ath9k_hw_set_sta_beacon_timers(struct ath_hal *ah,
+ const struct ath9k_beacon_state *bs)
+{
+ u32 nextTbtt, beaconintval, dtimperiod, beacontimeout;
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ REG_WRITE(ah, AR_NEXT_TBTT_TIMER, TU_TO_USEC(bs->bs_nexttbtt));
+
+ REG_WRITE(ah, AR_BEACON_PERIOD,
+ TU_TO_USEC(bs->bs_intval & ATH9K_BEACON_PERIOD));
+ REG_WRITE(ah, AR_DMA_BEACON_PERIOD,
+ TU_TO_USEC(bs->bs_intval & ATH9K_BEACON_PERIOD));
+
+ REG_RMW_FIELD(ah, AR_RSSI_THR,
+ AR_RSSI_THR_BM_THR, bs->bs_bmissthreshold);
+
+ beaconintval = bs->bs_intval & ATH9K_BEACON_PERIOD;
+
+ if (bs->bs_sleepduration > beaconintval)
+ beaconintval = bs->bs_sleepduration;
+
+ dtimperiod = bs->bs_dtimperiod;
+ if (bs->bs_sleepduration > dtimperiod)
+ dtimperiod = bs->bs_sleepduration;
+
+ if (beaconintval == dtimperiod)
+ nextTbtt = bs->bs_nextdtim;
+ else
+ nextTbtt = bs->bs_nexttbtt;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_BEACON, "%s: next DTIM %d\n", __func__,
+ bs->bs_nextdtim);
+ DPRINTF(ah->ah_sc, ATH_DBG_BEACON, "%s: next beacon %d\n", __func__,
+ nextTbtt);
+ DPRINTF(ah->ah_sc, ATH_DBG_BEACON, "%s: beacon period %d\n", __func__,
+ beaconintval);
+ DPRINTF(ah->ah_sc, ATH_DBG_BEACON, "%s: DTIM period %d\n", __func__,
+ dtimperiod);
+
+ REG_WRITE(ah, AR_NEXT_DTIM,
+ TU_TO_USEC(bs->bs_nextdtim - SLEEP_SLOP));
+ REG_WRITE(ah, AR_NEXT_TIM, TU_TO_USEC(nextTbtt - SLEEP_SLOP));
+
+ REG_WRITE(ah, AR_SLEEP1,
+ SM((CAB_TIMEOUT_VAL << 3), AR_SLEEP1_CAB_TIMEOUT)
+ | AR_SLEEP1_ASSUME_DTIM);
+
+ if (pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP)
+ beacontimeout = (BEACON_TIMEOUT_VAL << 3);
+ else
+ beacontimeout = MIN_BEACON_TIMEOUT_VAL;
+
+ REG_WRITE(ah, AR_SLEEP2,
+ SM(beacontimeout, AR_SLEEP2_BEACON_TIMEOUT));
+
+ REG_WRITE(ah, AR_TIM_PERIOD, TU_TO_USEC(beaconintval));
+ REG_WRITE(ah, AR_DTIM_PERIOD, TU_TO_USEC(dtimperiod));
+
+ REG_SET_BIT(ah, AR_TIMER_MODE,
+ AR_TBTT_TIMER_EN | AR_TIM_TIMER_EN |
+ AR_DTIM_TIMER_EN);
+
+}
+
+bool ath9k_hw_keyisvalid(struct ath_hal *ah, u16 entry)
+{
+ if (entry < ah->ah_caps.keycache_size) {
+ u32 val = REG_READ(ah, AR_KEYTABLE_MAC1(entry));
+ if (val & AR_KEYTABLE_VALID)
+ return true;
+ }
+ return false;
+}
+
+bool ath9k_hw_keyreset(struct ath_hal *ah, u16 entry)
+{
+ u32 keyType;
+
+ if (entry >= ah->ah_caps.keycache_size) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: entry %u out of range\n", __func__, entry);
+ return false;
+ }
+ keyType = REG_READ(ah, AR_KEYTABLE_TYPE(entry));
+
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY4(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_TYPE(entry), AR_KEYTABLE_TYPE_CLR);
+ REG_WRITE(ah, AR_KEYTABLE_MAC0(entry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_MAC1(entry), 0);
+
+ if (keyType == AR_KEYTABLE_TYPE_TKIP && ATH9K_IS_MIC_ENABLED(ah)) {
+ u16 micentry = entry + 64;
+
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(micentry), 0);
+
+ }
+
+ if (ah->ah_curchan == NULL)
+ return true;
+
+ return true;
+}
+
+bool
+ath9k_hw_keysetmac(struct ath_hal *ah, u16 entry,
+ const u8 *mac)
+{
+ u32 macHi, macLo;
+
+ if (entry >= ah->ah_caps.keycache_size) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: entry %u out of range\n", __func__, entry);
+ return false;
+ }
+
+ if (mac != NULL) {
+ macHi = (mac[5] << 8) | mac[4];
+ macLo = (mac[3] << 24) | (mac[2] << 16)
+ | (mac[1] << 8) | mac[0];
+ macLo >>= 1;
+ macLo |= (macHi & 1) << 31;
+ macHi >>= 1;
+ } else {
+ macLo = macHi = 0;
+ }
+ REG_WRITE(ah, AR_KEYTABLE_MAC0(entry), macLo);
+ REG_WRITE(ah, AR_KEYTABLE_MAC1(entry), macHi | AR_KEYTABLE_VALID);
+
+ return true;
+}
+
+bool
+ath9k_hw_set_keycache_entry(struct ath_hal *ah, u16 entry,
+ const struct ath9k_keyval *k,
+ const u8 *mac, int xorKey)
+{
+ const struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ u32 key0, key1, key2, key3, key4;
+ u32 keyType;
+ u32 xorMask = xorKey ?
+ (ATH9K_KEY_XOR << 24 | ATH9K_KEY_XOR << 16 | ATH9K_KEY_XOR << 8
+ | ATH9K_KEY_XOR) : 0;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (entry >= pCap->keycache_size) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: entry %u out of range\n", __func__, entry);
+ return false;
+ }
+ switch (k->kv_type) {
+ case ATH9K_CIPHER_AES_OCB:
+ keyType = AR_KEYTABLE_TYPE_AES;
+ break;
+ case ATH9K_CIPHER_AES_CCM:
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_CIPHER_AESCCM)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: AES-CCM not supported by "
+ "mac rev 0x%x\n", __func__,
+ ah->ah_macRev);
+ return false;
+ }
+ keyType = AR_KEYTABLE_TYPE_CCM;
+ break;
+ case ATH9K_CIPHER_TKIP:
+ keyType = AR_KEYTABLE_TYPE_TKIP;
+ if (ATH9K_IS_MIC_ENABLED(ah)
+ && entry + 64 >= pCap->keycache_size) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: entry %u inappropriate for TKIP\n",
+ __func__, entry);
+ return false;
+ }
+ break;
+ case ATH9K_CIPHER_WEP:
+ if (k->kv_len < 40 / NBBY) {
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: WEP key length %u too small\n",
+ __func__, k->kv_len);
+ return false;
+ }
+ if (k->kv_len <= 40 / NBBY)
+ keyType = AR_KEYTABLE_TYPE_40;
+ else if (k->kv_len <= 104 / NBBY)
+ keyType = AR_KEYTABLE_TYPE_104;
+ else
+ keyType = AR_KEYTABLE_TYPE_128;
+ break;
+ case ATH9K_CIPHER_CLR:
+ keyType = AR_KEYTABLE_TYPE_CLR;
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_KEYCACHE,
+ "%s: cipher %u not supported\n", __func__,
+ k->kv_type);
+ return false;
+ }
+
+ key0 = get_unaligned_le32(k->kv_val + 0) ^ xorMask;
+ key1 = (get_unaligned_le16(k->kv_val + 4) ^ xorMask) & 0xffff;
+ key2 = get_unaligned_le32(k->kv_val + 6) ^ xorMask;
+ key3 = (get_unaligned_le16(k->kv_val + 10) ^ xorMask) & 0xffff;
+ key4 = get_unaligned_le32(k->kv_val + 12) ^ xorMask;
+ if (k->kv_len <= 104 / NBBY)
+ key4 &= 0xff;
+
+ if (keyType == AR_KEYTABLE_TYPE_TKIP && ATH9K_IS_MIC_ENABLED(ah)) {
+ u16 micentry = entry + 64;
+
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(entry), ~key0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(entry), ~key1);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(entry), key2);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(entry), key3);
+ REG_WRITE(ah, AR_KEYTABLE_KEY4(entry), key4);
+ REG_WRITE(ah, AR_KEYTABLE_TYPE(entry), keyType);
+ (void) ath9k_hw_keysetmac(ah, entry, mac);
+
+ if (ahp->ah_miscMode & AR_PCU_MIC_NEW_LOC_ENA) {
+ u32 mic0, mic1, mic2, mic3, mic4;
+
+ mic0 = get_unaligned_le32(k->kv_mic + 0);
+ mic2 = get_unaligned_le32(k->kv_mic + 4);
+ mic1 = get_unaligned_le16(k->kv_txmic + 2) & 0xffff;
+ mic3 = get_unaligned_le16(k->kv_txmic + 0) & 0xffff;
+ mic4 = get_unaligned_le32(k->kv_txmic + 4);
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(micentry), mic0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(micentry), mic1);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(micentry), mic2);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(micentry), mic3);
+ REG_WRITE(ah, AR_KEYTABLE_KEY4(micentry), mic4);
+ REG_WRITE(ah, AR_KEYTABLE_TYPE(micentry),
+ AR_KEYTABLE_TYPE_CLR);
+
+ } else {
+ u32 mic0, mic2;
+
+ mic0 = get_unaligned_le32(k->kv_mic + 0);
+ mic2 = get_unaligned_le32(k->kv_mic + 4);
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(micentry), mic0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(micentry), mic2);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY4(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_TYPE(micentry),
+ AR_KEYTABLE_TYPE_CLR);
+ }
+ REG_WRITE(ah, AR_KEYTABLE_MAC0(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_MAC1(micentry), 0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(entry), key0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(entry), key1);
+ } else {
+ REG_WRITE(ah, AR_KEYTABLE_KEY0(entry), key0);
+ REG_WRITE(ah, AR_KEYTABLE_KEY1(entry), key1);
+ REG_WRITE(ah, AR_KEYTABLE_KEY2(entry), key2);
+ REG_WRITE(ah, AR_KEYTABLE_KEY3(entry), key3);
+ REG_WRITE(ah, AR_KEYTABLE_KEY4(entry), key4);
+ REG_WRITE(ah, AR_KEYTABLE_TYPE(entry), keyType);
+
+ (void) ath9k_hw_keysetmac(ah, entry, mac);
+ }
+
+ if (ah->ah_curchan == NULL)
+ return true;
+
+ return true;
+}
+
+bool
+ath9k_hw_updatetxtriglevel(struct ath_hal *ah, bool bIncTrigLevel)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 txcfg, curLevel, newLevel;
+ enum ath9k_int omask;
+
+ if (ah->ah_txTrigLevel >= MAX_TX_FIFO_THRESHOLD)
+ return false;
+
+ omask = ath9k_hw_set_interrupts(ah,
+ ahp->ah_maskReg & ~ATH9K_INT_GLOBAL);
+
+ txcfg = REG_READ(ah, AR_TXCFG);
+ curLevel = MS(txcfg, AR_FTRIG);
+ newLevel = curLevel;
+ if (bIncTrigLevel) {
+ if (curLevel < MAX_TX_FIFO_THRESHOLD)
+ newLevel++;
+ } else if (curLevel > MIN_TX_FIFO_THRESHOLD)
+ newLevel--;
+ if (newLevel != curLevel)
+ REG_WRITE(ah, AR_TXCFG,
+ (txcfg & ~AR_FTRIG) | SM(newLevel, AR_FTRIG));
+
+ ath9k_hw_set_interrupts(ah, omask);
+
+ ah->ah_txTrigLevel = newLevel;
+
+ return newLevel != curLevel;
+}
+
+bool ath9k_hw_set_txq_props(struct ath_hal *ah, int q,
+ const struct ath9k_tx_queue_info *qinfo)
+{
+ u32 cw;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ struct ath9k_tx_queue_info *qi;
+
+ if (q >= pCap->total_queues) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: invalid queue num %u\n",
+ __func__, q);
+ return false;
+ }
+
+ qi = &ahp->ah_txq[q];
+ if (qi->tqi_type == ATH9K_TX_QUEUE_INACTIVE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: inactive queue\n",
+ __func__);
+ return false;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: queue %p\n", __func__, qi);
+
+ qi->tqi_ver = qinfo->tqi_ver;
+ qi->tqi_subtype = qinfo->tqi_subtype;
+ qi->tqi_qflags = qinfo->tqi_qflags;
+ qi->tqi_priority = qinfo->tqi_priority;
+ if (qinfo->tqi_aifs != ATH9K_TXQ_USEDEFAULT)
+ qi->tqi_aifs = min(qinfo->tqi_aifs, 255U);
+ else
+ qi->tqi_aifs = INIT_AIFS;
+ if (qinfo->tqi_cwmin != ATH9K_TXQ_USEDEFAULT) {
+ cw = min(qinfo->tqi_cwmin, 1024U);
+ qi->tqi_cwmin = 1;
+ while (qi->tqi_cwmin < cw)
+ qi->tqi_cwmin = (qi->tqi_cwmin << 1) | 1;
+ } else
+ qi->tqi_cwmin = qinfo->tqi_cwmin;
+ if (qinfo->tqi_cwmax != ATH9K_TXQ_USEDEFAULT) {
+ cw = min(qinfo->tqi_cwmax, 1024U);
+ qi->tqi_cwmax = 1;
+ while (qi->tqi_cwmax < cw)
+ qi->tqi_cwmax = (qi->tqi_cwmax << 1) | 1;
+ } else
+ qi->tqi_cwmax = INIT_CWMAX;
+
+ if (qinfo->tqi_shretry != 0)
+ qi->tqi_shretry = min((u32) qinfo->tqi_shretry, 15U);
+ else
+ qi->tqi_shretry = INIT_SH_RETRY;
+ if (qinfo->tqi_lgretry != 0)
+ qi->tqi_lgretry = min((u32) qinfo->tqi_lgretry, 15U);
+ else
+ qi->tqi_lgretry = INIT_LG_RETRY;
+ qi->tqi_cbrPeriod = qinfo->tqi_cbrPeriod;
+ qi->tqi_cbrOverflowLimit = qinfo->tqi_cbrOverflowLimit;
+ qi->tqi_burstTime = qinfo->tqi_burstTime;
+ qi->tqi_readyTime = qinfo->tqi_readyTime;
+
+ switch (qinfo->tqi_subtype) {
+ case ATH9K_WME_UPSD:
+ if (qi->tqi_type == ATH9K_TX_QUEUE_DATA)
+ qi->tqi_intFlags = ATH9K_TXQ_USE_LOCKOUT_BKOFF_DIS;
+ break;
+ default:
+ break;
+ }
+ return true;
+}
+
+bool ath9k_hw_get_txq_props(struct ath_hal *ah, int q,
+ struct ath9k_tx_queue_info *qinfo)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ struct ath9k_tx_queue_info *qi;
+
+ if (q >= pCap->total_queues) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: invalid queue num %u\n",
+ __func__, q);
+ return false;
+ }
+
+ qi = &ahp->ah_txq[q];
+ if (qi->tqi_type == ATH9K_TX_QUEUE_INACTIVE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: inactive queue\n",
+ __func__);
+ return false;
+ }
+
+ qinfo->tqi_qflags = qi->tqi_qflags;
+ qinfo->tqi_ver = qi->tqi_ver;
+ qinfo->tqi_subtype = qi->tqi_subtype;
+ qinfo->tqi_qflags = qi->tqi_qflags;
+ qinfo->tqi_priority = qi->tqi_priority;
+ qinfo->tqi_aifs = qi->tqi_aifs;
+ qinfo->tqi_cwmin = qi->tqi_cwmin;
+ qinfo->tqi_cwmax = qi->tqi_cwmax;
+ qinfo->tqi_shretry = qi->tqi_shretry;
+ qinfo->tqi_lgretry = qi->tqi_lgretry;
+ qinfo->tqi_cbrPeriod = qi->tqi_cbrPeriod;
+ qinfo->tqi_cbrOverflowLimit = qi->tqi_cbrOverflowLimit;
+ qinfo->tqi_burstTime = qi->tqi_burstTime;
+ qinfo->tqi_readyTime = qi->tqi_readyTime;
+
+ return true;
+}
+
+int
+ath9k_hw_setuptxqueue(struct ath_hal *ah, enum ath9k_tx_queue type,
+ const struct ath9k_tx_queue_info *qinfo)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_tx_queue_info *qi;
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ int q;
+
+ switch (type) {
+ case ATH9K_TX_QUEUE_BEACON:
+ q = pCap->total_queues - 1;
+ break;
+ case ATH9K_TX_QUEUE_CAB:
+ q = pCap->total_queues - 2;
+ break;
+ case ATH9K_TX_QUEUE_PSPOLL:
+ q = 1;
+ break;
+ case ATH9K_TX_QUEUE_UAPSD:
+ q = pCap->total_queues - 3;
+ break;
+ case ATH9K_TX_QUEUE_DATA:
+ for (q = 0; q < pCap->total_queues; q++)
+ if (ahp->ah_txq[q].tqi_type ==
+ ATH9K_TX_QUEUE_INACTIVE)
+ break;
+ if (q == pCap->total_queues) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: no available tx queue\n", __func__);
+ return -1;
+ }
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: bad tx queue type %u\n",
+ __func__, type);
+ return -1;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: queue %u\n", __func__, q);
+
+ qi = &ahp->ah_txq[q];
+ if (qi->tqi_type != ATH9K_TX_QUEUE_INACTIVE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: tx queue %u already active\n", __func__, q);
+ return -1;
+ }
+ memset(qi, 0, sizeof(struct ath9k_tx_queue_info));
+ qi->tqi_type = type;
+ if (qinfo == NULL) {
+ qi->tqi_qflags =
+ TXQ_FLAG_TXOKINT_ENABLE
+ | TXQ_FLAG_TXERRINT_ENABLE
+ | TXQ_FLAG_TXDESCINT_ENABLE | TXQ_FLAG_TXURNINT_ENABLE;
+ qi->tqi_aifs = INIT_AIFS;
+ qi->tqi_cwmin = ATH9K_TXQ_USEDEFAULT;
+ qi->tqi_cwmax = INIT_CWMAX;
+ qi->tqi_shretry = INIT_SH_RETRY;
+ qi->tqi_lgretry = INIT_LG_RETRY;
+ qi->tqi_physCompBuf = 0;
+ } else {
+ qi->tqi_physCompBuf = qinfo->tqi_physCompBuf;
+ (void) ath9k_hw_set_txq_props(ah, q, qinfo);
+ }
+
+ return q;
+}
+
+static void
+ath9k_hw_set_txq_interrupts(struct ath_hal *ah,
+ struct ath9k_tx_queue_info *qi)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_INTERRUPT,
+ "%s: tx ok 0x%x err 0x%x desc 0x%x eol 0x%x urn 0x%x\n",
+ __func__, ahp->ah_txOkInterruptMask,
+ ahp->ah_txErrInterruptMask, ahp->ah_txDescInterruptMask,
+ ahp->ah_txEolInterruptMask, ahp->ah_txUrnInterruptMask);
+
+ REG_WRITE(ah, AR_IMR_S0,
+ SM(ahp->ah_txOkInterruptMask, AR_IMR_S0_QCU_TXOK)
+ | SM(ahp->ah_txDescInterruptMask, AR_IMR_S0_QCU_TXDESC));
+ REG_WRITE(ah, AR_IMR_S1,
+ SM(ahp->ah_txErrInterruptMask, AR_IMR_S1_QCU_TXERR)
+ | SM(ahp->ah_txEolInterruptMask, AR_IMR_S1_QCU_TXEOL));
+ REG_RMW_FIELD(ah, AR_IMR_S2,
+ AR_IMR_S2_QCU_TXURN, ahp->ah_txUrnInterruptMask);
+}
+
+bool ath9k_hw_releasetxqueue(struct ath_hal *ah, u32 q)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ struct ath9k_tx_queue_info *qi;
+
+ if (q >= pCap->total_queues) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: invalid queue num %u\n",
+ __func__, q);
+ return false;
+ }
+ qi = &ahp->ah_txq[q];
+ if (qi->tqi_type == ATH9K_TX_QUEUE_INACTIVE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: inactive queue %u\n",
+ __func__, q);
+ return false;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: release queue %u\n",
+ __func__, q);
+
+ qi->tqi_type = ATH9K_TX_QUEUE_INACTIVE;
+ ahp->ah_txOkInterruptMask &= ~(1 << q);
+ ahp->ah_txErrInterruptMask &= ~(1 << q);
+ ahp->ah_txDescInterruptMask &= ~(1 << q);
+ ahp->ah_txEolInterruptMask &= ~(1 << q);
+ ahp->ah_txUrnInterruptMask &= ~(1 << q);
+ ath9k_hw_set_txq_interrupts(ah, qi);
+
+ return true;
+}
+
+bool ath9k_hw_resettxqueue(struct ath_hal *ah, u32 q)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+ struct ath9k_channel *chan = ah->ah_curchan;
+ struct ath9k_tx_queue_info *qi;
+ u32 cwMin, chanCwMin, value;
+
+ if (q >= pCap->total_queues) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: invalid queue num %u\n",
+ __func__, q);
+ return false;
+ }
+ qi = &ahp->ah_txq[q];
+ if (qi->tqi_type == ATH9K_TX_QUEUE_INACTIVE) {
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: inactive queue %u\n",
+ __func__, q);
+ return true;
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: reset queue %u\n", __func__, q);
+
+ if (qi->tqi_cwmin == ATH9K_TXQ_USEDEFAULT) {
+ if (chan && IS_CHAN_B(chan))
+ chanCwMin = INIT_CWMIN_11B;
+ else
+ chanCwMin = INIT_CWMIN;
+
+ for (cwMin = 1; cwMin < chanCwMin; cwMin = (cwMin << 1) | 1);
+ } else
+ cwMin = qi->tqi_cwmin;
+
+ REG_WRITE(ah, AR_DLCL_IFS(q), SM(cwMin, AR_D_LCL_IFS_CWMIN)
+ | SM(qi->tqi_cwmax, AR_D_LCL_IFS_CWMAX)
+ | SM(qi->tqi_aifs, AR_D_LCL_IFS_AIFS));
+
+ REG_WRITE(ah, AR_DRETRY_LIMIT(q),
+ SM(INIT_SSH_RETRY, AR_D_RETRY_LIMIT_STA_SH)
+ | SM(INIT_SLG_RETRY, AR_D_RETRY_LIMIT_STA_LG)
+ | SM(qi->tqi_shretry, AR_D_RETRY_LIMIT_FR_SH)
+ );
+
+ REG_WRITE(ah, AR_QMISC(q), AR_Q_MISC_DCU_EARLY_TERM_REQ);
+ REG_WRITE(ah, AR_DMISC(q),
+ AR_D_MISC_CW_BKOFF_EN | AR_D_MISC_FRAG_WAIT_EN | 0x2);
+
+ if (qi->tqi_cbrPeriod) {
+ REG_WRITE(ah, AR_QCBRCFG(q),
+ SM(qi->tqi_cbrPeriod, AR_Q_CBRCFG_INTERVAL)
+ | SM(qi->tqi_cbrOverflowLimit,
+ AR_Q_CBRCFG_OVF_THRESH));
+ REG_WRITE(ah, AR_QMISC(q),
+ REG_READ(ah,
+ AR_QMISC(q)) | AR_Q_MISC_FSP_CBR | (qi->
+ tqi_cbrOverflowLimit
+ ?
+ AR_Q_MISC_CBR_EXP_CNTR_LIMIT_EN
+ :
+ 0));
+ }
+ if (qi->tqi_readyTime && (qi->tqi_type != ATH9K_TX_QUEUE_CAB)) {
+ REG_WRITE(ah, AR_QRDYTIMECFG(q),
+ SM(qi->tqi_readyTime, AR_Q_RDYTIMECFG_DURATION) |
+ AR_Q_RDYTIMECFG_EN);
+ }
+
+ REG_WRITE(ah, AR_DCHNTIME(q),
+ SM(qi->tqi_burstTime, AR_D_CHNTIME_DUR) |
+ (qi->tqi_burstTime ? AR_D_CHNTIME_EN : 0));
+
+ if (qi->tqi_burstTime
+ && (qi->tqi_qflags & TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE)) {
+ REG_WRITE(ah, AR_QMISC(q),
+ REG_READ(ah,
+ AR_QMISC(q)) |
+ AR_Q_MISC_RDYTIME_EXP_POLICY);
+
+ }
+
+ if (qi->tqi_qflags & TXQ_FLAG_BACKOFF_DISABLE) {
+ REG_WRITE(ah, AR_DMISC(q),
+ REG_READ(ah, AR_DMISC(q)) |
+ AR_D_MISC_POST_FR_BKOFF_DIS);
+ }
+ if (qi->tqi_qflags & TXQ_FLAG_FRAG_BURST_BACKOFF_ENABLE) {
+ REG_WRITE(ah, AR_DMISC(q),
+ REG_READ(ah, AR_DMISC(q)) |
+ AR_D_MISC_FRAG_BKOFF_EN);
+ }
+ switch (qi->tqi_type) {
+ case ATH9K_TX_QUEUE_BEACON:
+ REG_WRITE(ah, AR_QMISC(q), REG_READ(ah, AR_QMISC(q))
+ | AR_Q_MISC_FSP_DBA_GATED
+ | AR_Q_MISC_BEACON_USE
+ | AR_Q_MISC_CBR_INCR_DIS1);
+
+ REG_WRITE(ah, AR_DMISC(q), REG_READ(ah, AR_DMISC(q))
+ | (AR_D_MISC_ARB_LOCKOUT_CNTRL_GLOBAL <<
+ AR_D_MISC_ARB_LOCKOUT_CNTRL_S)
+ | AR_D_MISC_BEACON_USE
+ | AR_D_MISC_POST_FR_BKOFF_DIS);
+ break;
+ case ATH9K_TX_QUEUE_CAB:
+ REG_WRITE(ah, AR_QMISC(q), REG_READ(ah, AR_QMISC(q))
+ | AR_Q_MISC_FSP_DBA_GATED
+ | AR_Q_MISC_CBR_INCR_DIS1
+ | AR_Q_MISC_CBR_INCR_DIS0);
+ value = (qi->tqi_readyTime
+ - (ah->ah_config.sw_beacon_response_time -
+ ah->ah_config.dma_beacon_response_time)
+ -
+ ah->ah_config.additional_swba_backoff) *
+ 1024;
+ REG_WRITE(ah, AR_QRDYTIMECFG(q),
+ value | AR_Q_RDYTIMECFG_EN);
+ REG_WRITE(ah, AR_DMISC(q), REG_READ(ah, AR_DMISC(q))
+ | (AR_D_MISC_ARB_LOCKOUT_CNTRL_GLOBAL <<
+ AR_D_MISC_ARB_LOCKOUT_CNTRL_S));
+ break;
+ case ATH9K_TX_QUEUE_PSPOLL:
+ REG_WRITE(ah, AR_QMISC(q),
+ REG_READ(ah,
+ AR_QMISC(q)) | AR_Q_MISC_CBR_INCR_DIS1);
+ break;
+ case ATH9K_TX_QUEUE_UAPSD:
+ REG_WRITE(ah, AR_DMISC(q), REG_READ(ah, AR_DMISC(q))
+ | AR_D_MISC_POST_FR_BKOFF_DIS);
+ break;
+ default:
+ break;
+ }
+
+ if (qi->tqi_intFlags & ATH9K_TXQ_USE_LOCKOUT_BKOFF_DIS) {
+ REG_WRITE(ah, AR_DMISC(q),
+ REG_READ(ah, AR_DMISC(q)) |
+ SM(AR_D_MISC_ARB_LOCKOUT_CNTRL_GLOBAL,
+ AR_D_MISC_ARB_LOCKOUT_CNTRL) |
+ AR_D_MISC_POST_FR_BKOFF_DIS);
+ }
+
+ if (qi->tqi_qflags & TXQ_FLAG_TXOKINT_ENABLE)
+ ahp->ah_txOkInterruptMask |= 1 << q;
+ else
+ ahp->ah_txOkInterruptMask &= ~(1 << q);
+ if (qi->tqi_qflags & TXQ_FLAG_TXERRINT_ENABLE)
+ ahp->ah_txErrInterruptMask |= 1 << q;
+ else
+ ahp->ah_txErrInterruptMask &= ~(1 << q);
+ if (qi->tqi_qflags & TXQ_FLAG_TXDESCINT_ENABLE)
+ ahp->ah_txDescInterruptMask |= 1 << q;
+ else
+ ahp->ah_txDescInterruptMask &= ~(1 << q);
+ if (qi->tqi_qflags & TXQ_FLAG_TXEOLINT_ENABLE)
+ ahp->ah_txEolInterruptMask |= 1 << q;
+ else
+ ahp->ah_txEolInterruptMask &= ~(1 << q);
+ if (qi->tqi_qflags & TXQ_FLAG_TXURNINT_ENABLE)
+ ahp->ah_txUrnInterruptMask |= 1 << q;
+ else
+ ahp->ah_txUrnInterruptMask &= ~(1 << q);
+ ath9k_hw_set_txq_interrupts(ah, qi);
+
+ return true;
+}
+
+void ath9k_hw_gettxintrtxqs(struct ath_hal *ah, u32 *txqs)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ *txqs &= ahp->ah_intrTxqs;
+ ahp->ah_intrTxqs &= ~(*txqs);
+}
+
+bool
+ath9k_hw_filltxdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 segLen, bool firstSeg,
+ bool lastSeg, const struct ath_desc *ds0)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ if (firstSeg) {
+ ads->ds_ctl1 |= segLen | (lastSeg ? 0 : AR_TxMore);
+ } else if (lastSeg) {
+ ads->ds_ctl0 = 0;
+ ads->ds_ctl1 = segLen;
+ ads->ds_ctl2 = AR5416DESC_CONST(ds0)->ds_ctl2;
+ ads->ds_ctl3 = AR5416DESC_CONST(ds0)->ds_ctl3;
+ } else {
+ ads->ds_ctl0 = 0;
+ ads->ds_ctl1 = segLen | AR_TxMore;
+ ads->ds_ctl2 = 0;
+ ads->ds_ctl3 = 0;
+ }
+ ads->ds_txstatus0 = ads->ds_txstatus1 = 0;
+ ads->ds_txstatus2 = ads->ds_txstatus3 = 0;
+ ads->ds_txstatus4 = ads->ds_txstatus5 = 0;
+ ads->ds_txstatus6 = ads->ds_txstatus7 = 0;
+ ads->ds_txstatus8 = ads->ds_txstatus9 = 0;
+ return true;
+}
+
+void ath9k_hw_cleartxdesc(struct ath_hal *ah, struct ath_desc *ds)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ ads->ds_txstatus0 = ads->ds_txstatus1 = 0;
+ ads->ds_txstatus2 = ads->ds_txstatus3 = 0;
+ ads->ds_txstatus4 = ads->ds_txstatus5 = 0;
+ ads->ds_txstatus6 = ads->ds_txstatus7 = 0;
+ ads->ds_txstatus8 = ads->ds_txstatus9 = 0;
+}
+
+int
+ath9k_hw_txprocdesc(struct ath_hal *ah, struct ath_desc *ds)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ if ((ads->ds_txstatus9 & AR_TxDone) == 0)
+ return -EINPROGRESS;
+
+ ds->ds_txstat.ts_seqnum = MS(ads->ds_txstatus9, AR_SeqNum);
+ ds->ds_txstat.ts_tstamp = ads->AR_SendTimestamp;
+ ds->ds_txstat.ts_status = 0;
+ ds->ds_txstat.ts_flags = 0;
+
+ if (ads->ds_txstatus1 & AR_ExcessiveRetries)
+ ds->ds_txstat.ts_status |= ATH9K_TXERR_XRETRY;
+ if (ads->ds_txstatus1 & AR_Filtered)
+ ds->ds_txstat.ts_status |= ATH9K_TXERR_FILT;
+ if (ads->ds_txstatus1 & AR_FIFOUnderrun)
+ ds->ds_txstat.ts_status |= ATH9K_TXERR_FIFO;
+ if (ads->ds_txstatus9 & AR_TxOpExceeded)
+ ds->ds_txstat.ts_status |= ATH9K_TXERR_XTXOP;
+ if (ads->ds_txstatus1 & AR_TxTimerExpired)
+ ds->ds_txstat.ts_status |= ATH9K_TXERR_TIMER_EXPIRED;
+
+ if (ads->ds_txstatus1 & AR_DescCfgErr)
+ ds->ds_txstat.ts_flags |= ATH9K_TX_DESC_CFG_ERR;
+ if (ads->ds_txstatus1 & AR_TxDataUnderrun) {
+ ds->ds_txstat.ts_flags |= ATH9K_TX_DATA_UNDERRUN;
+ ath9k_hw_updatetxtriglevel(ah, true);
+ }
+ if (ads->ds_txstatus1 & AR_TxDelimUnderrun) {
+ ds->ds_txstat.ts_flags |= ATH9K_TX_DELIM_UNDERRUN;
+ ath9k_hw_updatetxtriglevel(ah, true);
+ }
+ if (ads->ds_txstatus0 & AR_TxBaStatus) {
+ ds->ds_txstat.ts_flags |= ATH9K_TX_BA;
+ ds->ds_txstat.ba_low = ads->AR_BaBitmapLow;
+ ds->ds_txstat.ba_high = ads->AR_BaBitmapHigh;
+ }
+
+ ds->ds_txstat.ts_rateindex = MS(ads->ds_txstatus9, AR_FinalTxIdx);
+ switch (ds->ds_txstat.ts_rateindex) {
+ case 0:
+ ds->ds_txstat.ts_ratecode = MS(ads->ds_ctl3, AR_XmitRate0);
+ break;
+ case 1:
+ ds->ds_txstat.ts_ratecode = MS(ads->ds_ctl3, AR_XmitRate1);
+ break;
+ case 2:
+ ds->ds_txstat.ts_ratecode = MS(ads->ds_ctl3, AR_XmitRate2);
+ break;
+ case 3:
+ ds->ds_txstat.ts_ratecode = MS(ads->ds_ctl3, AR_XmitRate3);
+ break;
+ }
+
+ ds->ds_txstat.ts_rssi = MS(ads->ds_txstatus5, AR_TxRSSICombined);
+ ds->ds_txstat.ts_rssi_ctl0 = MS(ads->ds_txstatus0, AR_TxRSSIAnt00);
+ ds->ds_txstat.ts_rssi_ctl1 = MS(ads->ds_txstatus0, AR_TxRSSIAnt01);
+ ds->ds_txstat.ts_rssi_ctl2 = MS(ads->ds_txstatus0, AR_TxRSSIAnt02);
+ ds->ds_txstat.ts_rssi_ext0 = MS(ads->ds_txstatus5, AR_TxRSSIAnt10);
+ ds->ds_txstat.ts_rssi_ext1 = MS(ads->ds_txstatus5, AR_TxRSSIAnt11);
+ ds->ds_txstat.ts_rssi_ext2 = MS(ads->ds_txstatus5, AR_TxRSSIAnt12);
+ ds->ds_txstat.evm0 = ads->AR_TxEVM0;
+ ds->ds_txstat.evm1 = ads->AR_TxEVM1;
+ ds->ds_txstat.evm2 = ads->AR_TxEVM2;
+ ds->ds_txstat.ts_shortretry = MS(ads->ds_txstatus1, AR_RTSFailCnt);
+ ds->ds_txstat.ts_longretry = MS(ads->ds_txstatus1, AR_DataFailCnt);
+ ds->ds_txstat.ts_virtcol = MS(ads->ds_txstatus1, AR_VirtRetryCnt);
+ ds->ds_txstat.ts_antenna = 1;
+
+ return 0;
+}
+
+void
+ath9k_hw_set11n_txdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 pktLen, enum ath9k_pkt_type type, u32 txPower,
+ u32 keyIx, enum ath9k_key_type keyType, u32 flags)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ txPower += ahp->ah_txPowerIndexOffset;
+ if (txPower > 63)
+ txPower = 63;
+
+ ads->ds_ctl0 = (pktLen & AR_FrameLen)
+ | (flags & ATH9K_TXDESC_VMF ? AR_VirtMoreFrag : 0)
+ | SM(txPower, AR_XmitPower)
+ | (flags & ATH9K_TXDESC_VEOL ? AR_VEOL : 0)
+ | (flags & ATH9K_TXDESC_CLRDMASK ? AR_ClrDestMask : 0)
+ | (flags & ATH9K_TXDESC_INTREQ ? AR_TxIntrReq : 0)
+ | (keyIx != ATH9K_TXKEYIX_INVALID ? AR_DestIdxValid : 0);
+
+ ads->ds_ctl1 =
+ (keyIx != ATH9K_TXKEYIX_INVALID ? SM(keyIx, AR_DestIdx) : 0)
+ | SM(type, AR_FrameType)
+ | (flags & ATH9K_TXDESC_NOACK ? AR_NoAck : 0)
+ | (flags & ATH9K_TXDESC_EXT_ONLY ? AR_ExtOnly : 0)
+ | (flags & ATH9K_TXDESC_EXT_AND_CTL ? AR_ExtAndCtl : 0);
+
+ ads->ds_ctl6 = SM(keyType, AR_EncrType);
+
+ if (AR_SREV_9285(ah)) {
+
+ ads->ds_ctl8 = 0;
+ ads->ds_ctl9 = 0;
+ ads->ds_ctl10 = 0;
+ ads->ds_ctl11 = 0;
+ }
+}
+
+void
+ath9k_hw_set11n_ratescenario(struct ath_hal *ah, struct ath_desc *ds,
+ struct ath_desc *lastds,
+ u32 durUpdateEn, u32 rtsctsRate,
+ u32 rtsctsDuration,
+ struct ath9k_11n_rate_series series[],
+ u32 nseries, u32 flags)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+ struct ar5416_desc *last_ads = AR5416DESC(lastds);
+ u32 ds_ctl0;
+
+ (void) nseries;
+ (void) rtsctsDuration;
+
+ if (flags & (ATH9K_TXDESC_RTSENA | ATH9K_TXDESC_CTSENA)) {
+ ds_ctl0 = ads->ds_ctl0;
+
+ if (flags & ATH9K_TXDESC_RTSENA) {
+ ds_ctl0 &= ~AR_CTSEnable;
+ ds_ctl0 |= AR_RTSEnable;
+ } else {
+ ds_ctl0 &= ~AR_RTSEnable;
+ ds_ctl0 |= AR_CTSEnable;
+ }
+
+ ads->ds_ctl0 = ds_ctl0;
+ } else {
+ ads->ds_ctl0 =
+ (ads->ds_ctl0 & ~(AR_RTSEnable | AR_CTSEnable));
+ }
+
+ ads->ds_ctl2 = set11nTries(series, 0)
+ | set11nTries(series, 1)
+ | set11nTries(series, 2)
+ | set11nTries(series, 3)
+ | (durUpdateEn ? AR_DurUpdateEna : 0)
+ | SM(0, AR_BurstDur);
+
+ ads->ds_ctl3 = set11nRate(series, 0)
+ | set11nRate(series, 1)
+ | set11nRate(series, 2)
+ | set11nRate(series, 3);
+
+ ads->ds_ctl4 = set11nPktDurRTSCTS(series, 0)
+ | set11nPktDurRTSCTS(series, 1);
+
+ ads->ds_ctl5 = set11nPktDurRTSCTS(series, 2)
+ | set11nPktDurRTSCTS(series, 3);
+
+ ads->ds_ctl7 = set11nRateFlags(series, 0)
+ | set11nRateFlags(series, 1)
+ | set11nRateFlags(series, 2)
+ | set11nRateFlags(series, 3)
+ | SM(rtsctsRate, AR_RTSCTSRate);
+ last_ads->ds_ctl2 = ads->ds_ctl2;
+ last_ads->ds_ctl3 = ads->ds_ctl3;
+}
+
+void
+ath9k_hw_set11n_aggr_first(struct ath_hal *ah, struct ath_desc *ds,
+ u32 aggrLen)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ ads->ds_ctl1 |= (AR_IsAggr | AR_MoreAggr);
+
+ ads->ds_ctl6 &= ~AR_AggrLen;
+ ads->ds_ctl6 |= SM(aggrLen, AR_AggrLen);
+}
+
+void
+ath9k_hw_set11n_aggr_middle(struct ath_hal *ah, struct ath_desc *ds,
+ u32 numDelims)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+ unsigned int ctl6;
+
+ ads->ds_ctl1 |= (AR_IsAggr | AR_MoreAggr);
+
+ ctl6 = ads->ds_ctl6;
+ ctl6 &= ~AR_PadDelim;
+ ctl6 |= SM(numDelims, AR_PadDelim);
+ ads->ds_ctl6 = ctl6;
+}
+
+void ath9k_hw_set11n_aggr_last(struct ath_hal *ah, struct ath_desc *ds)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ ads->ds_ctl1 |= AR_IsAggr;
+ ads->ds_ctl1 &= ~AR_MoreAggr;
+ ads->ds_ctl6 &= ~AR_PadDelim;
+}
+
+void ath9k_hw_clr11n_aggr(struct ath_hal *ah, struct ath_desc *ds)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ ads->ds_ctl1 &= (~AR_IsAggr & ~AR_MoreAggr);
+}
+
+void
+ath9k_hw_set11n_burstduration(struct ath_hal *ah, struct ath_desc *ds,
+ u32 burstDuration)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ ads->ds_ctl2 &= ~AR_BurstDur;
+ ads->ds_ctl2 |= SM(burstDuration, AR_BurstDur);
+}
+
+void
+ath9k_hw_set11n_virtualmorefrag(struct ath_hal *ah, struct ath_desc *ds,
+ u32 vmf)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+
+ if (vmf)
+ ads->ds_ctl0 |= AR_VirtMoreFrag;
+ else
+ ads->ds_ctl0 &= ~AR_VirtMoreFrag;
+}
+
+void ath9k_hw_putrxbuf(struct ath_hal *ah, u32 rxdp)
+{
+ REG_WRITE(ah, AR_RXDP, rxdp);
+}
+
+void ath9k_hw_rxena(struct ath_hal *ah)
+{
+ REG_WRITE(ah, AR_CR, AR_CR_RXE);
+}
+
+bool ath9k_hw_setrxabort(struct ath_hal *ah, bool set)
+{
+ if (set) {
+
+ REG_SET_BIT(ah, AR_DIAG_SW,
+ (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
+
+ if (!ath9k_hw_wait
+ (ah, AR_OBS_BUS_1, AR_OBS_BUS_1_RX_STATE, 0)) {
+ u32 reg;
+
+ REG_CLR_BIT(ah, AR_DIAG_SW,
+ (AR_DIAG_RX_DIS |
+ AR_DIAG_RX_ABORT));
+
+ reg = REG_READ(ah, AR_OBS_BUS_1);
+ DPRINTF(ah->ah_sc, ATH_DBG_FATAL,
+ "%s: rx failed to go idle in 10 ms RXSM=0x%x\n",
+ __func__, reg);
+
+ return false;
+ }
+ } else {
+ REG_CLR_BIT(ah, AR_DIAG_SW,
+ (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
+ }
+
+ return true;
+}
+
+void
+ath9k_hw_setmcastfilter(struct ath_hal *ah, u32 filter0,
+ u32 filter1)
+{
+ REG_WRITE(ah, AR_MCAST_FIL0, filter0);
+ REG_WRITE(ah, AR_MCAST_FIL1, filter1);
+}
+
+bool
+ath9k_hw_setuprxdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 size, u32 flags)
+{
+ struct ar5416_desc *ads = AR5416DESC(ds);
+ struct ath9k_hw_capabilities *pCap = &ah->ah_caps;
+
+ ads->ds_ctl1 = size & AR_BufLen;
+ if (flags & ATH9K_RXDESC_INTREQ)
+ ads->ds_ctl1 |= AR_RxIntrReq;
+
+ ads->ds_rxstatus8 &= ~AR_RxDone;
+ if (!(pCap->hw_caps & ATH9K_HW_CAP_AUTOSLEEP))
+ memset(&(ads->u), 0, sizeof(ads->u));
+ return true;
+}
+
+int
+ath9k_hw_rxprocdesc(struct ath_hal *ah, struct ath_desc *ds,
+ u32 pa, struct ath_desc *nds, u64 tsf)
+{
+ struct ar5416_desc ads;
+ struct ar5416_desc *adsp = AR5416DESC(ds);
+
+ if ((adsp->ds_rxstatus8 & AR_RxDone) == 0)
+ return -EINPROGRESS;
+
+ ads.u.rx = adsp->u.rx;
+
+ ds->ds_rxstat.rs_status = 0;
+ ds->ds_rxstat.rs_flags = 0;
+
+ ds->ds_rxstat.rs_datalen = ads.ds_rxstatus1 & AR_DataLen;
+ ds->ds_rxstat.rs_tstamp = ads.AR_RcvTimestamp;
+
+ ds->ds_rxstat.rs_rssi = MS(ads.ds_rxstatus4, AR_RxRSSICombined);
+ ds->ds_rxstat.rs_rssi_ctl0 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt00);
+ ds->ds_rxstat.rs_rssi_ctl1 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt01);
+ ds->ds_rxstat.rs_rssi_ctl2 = MS(ads.ds_rxstatus0, AR_RxRSSIAnt02);
+ ds->ds_rxstat.rs_rssi_ext0 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt10);
+ ds->ds_rxstat.rs_rssi_ext1 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt11);
+ ds->ds_rxstat.rs_rssi_ext2 = MS(ads.ds_rxstatus4, AR_RxRSSIAnt12);
+ if (ads.ds_rxstatus8 & AR_RxKeyIdxValid)
+ ds->ds_rxstat.rs_keyix = MS(ads.ds_rxstatus8, AR_KeyIdx);
+ else
+ ds->ds_rxstat.rs_keyix = ATH9K_RXKEYIX_INVALID;
+
+ ds->ds_rxstat.rs_rate = RXSTATUS_RATE(ah, (&ads));
+ ds->ds_rxstat.rs_more = (ads.ds_rxstatus1 & AR_RxMore) ? 1 : 0;
+
+ ds->ds_rxstat.rs_isaggr = (ads.ds_rxstatus8 & AR_RxAggr) ? 1 : 0;
+ ds->ds_rxstat.rs_moreaggr =
+ (ads.ds_rxstatus8 & AR_RxMoreAggr) ? 1 : 0;
+ ds->ds_rxstat.rs_antenna = MS(ads.ds_rxstatus3, AR_RxAntenna);
+ ds->ds_rxstat.rs_flags =
+ (ads.ds_rxstatus3 & AR_GI) ? ATH9K_RX_GI : 0;
+ ds->ds_rxstat.rs_flags |=
+ (ads.ds_rxstatus3 & AR_2040) ? ATH9K_RX_2040 : 0;
+
+ if (ads.ds_rxstatus8 & AR_PreDelimCRCErr)
+ ds->ds_rxstat.rs_flags |= ATH9K_RX_DELIM_CRC_PRE;
+ if (ads.ds_rxstatus8 & AR_PostDelimCRCErr)
+ ds->ds_rxstat.rs_flags |= ATH9K_RX_DELIM_CRC_POST;
+ if (ads.ds_rxstatus8 & AR_DecryptBusyErr)
+ ds->ds_rxstat.rs_flags |= ATH9K_RX_DECRYPT_BUSY;
+
+ if ((ads.ds_rxstatus8 & AR_RxFrameOK) == 0) {
+
+ if (ads.ds_rxstatus8 & AR_CRCErr)
+ ds->ds_rxstat.rs_status |= ATH9K_RXERR_CRC;
+ else if (ads.ds_rxstatus8 & AR_PHYErr) {
+ u32 phyerr;
+
+ ds->ds_rxstat.rs_status |= ATH9K_RXERR_PHY;
+ phyerr = MS(ads.ds_rxstatus8, AR_PHYErrCode);
+ ds->ds_rxstat.rs_phyerr = phyerr;
+ } else if (ads.ds_rxstatus8 & AR_DecryptCRCErr)
+ ds->ds_rxstat.rs_status |= ATH9K_RXERR_DECRYPT;
+ else if (ads.ds_rxstatus8 & AR_MichaelErr)
+ ds->ds_rxstat.rs_status |= ATH9K_RXERR_MIC;
+ }
+
+ return 0;
+}
+
+static void ath9k_hw_setup_rate_table(struct ath_hal *ah,
+ struct ath9k_rate_table *rt)
+{
+ int i;
+
+ if (rt->rateCodeToIndex[0] != 0)
+ return;
+ for (i = 0; i < 256; i++)
+ rt->rateCodeToIndex[i] = (u8) -1;
+ for (i = 0; i < rt->rateCount; i++) {
+ u8 code = rt->info[i].rateCode;
+ u8 cix = rt->info[i].controlRate;
+
+ rt->rateCodeToIndex[code] = i;
+ rt->rateCodeToIndex[code | rt->info[i].shortPreamble] = i;
+
+ rt->info[i].lpAckDuration =
+ ath9k_hw_computetxtime(ah, rt,
+ WLAN_CTRL_FRAME_SIZE,
+ cix,
+ false);
+ rt->info[i].spAckDuration =
+ ath9k_hw_computetxtime(ah, rt,
+ WLAN_CTRL_FRAME_SIZE,
+ cix,
+ true);
+ }
+}
+
+const struct ath9k_rate_table *ath9k_hw_getratetable(struct ath_hal *ah,
+ u32 mode)
+{
+ struct ath9k_rate_table *rt;
+ switch (mode) {
+ case ATH9K_MODE_11A:
+ rt = &ar5416_11a_table;
+ break;
+ case ATH9K_MODE_11B:
+ rt = &ar5416_11b_table;
+ break;
+ case ATH9K_MODE_11G:
+ rt = &ar5416_11g_table;
+ break;
+ case ATH9K_MODE_11NG_HT20:
+ case ATH9K_MODE_11NG_HT40PLUS:
+ case ATH9K_MODE_11NG_HT40MINUS:
+ rt = &ar5416_11ng_table;
+ break;
+ case ATH9K_MODE_11NA_HT20:
+ case ATH9K_MODE_11NA_HT40PLUS:
+ case ATH9K_MODE_11NA_HT40MINUS:
+ rt = &ar5416_11na_table;
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL, "%s: invalid mode 0x%x\n",
+ __func__, mode);
+ return NULL;
+ }
+ ath9k_hw_setup_rate_table(ah, rt);
+ return rt;
+}
+
+static const char *ath9k_hw_devname(u16 devid)
+{
+ switch (devid) {
+ case AR5416_DEVID_PCI:
+ case AR5416_DEVID_PCIE:
+ return "Atheros 5416";
+ case AR9160_DEVID_PCI:
+ return "Atheros 9160";
+ case AR9280_DEVID_PCI:
+ case AR9280_DEVID_PCIE:
+ return "Atheros 9280";
+ }
+ return NULL;
+}
+
+const char *ath9k_hw_probe(u16 vendorid, u16 devid)
+{
+ return vendorid == ATHEROS_VENDOR_ID ?
+ ath9k_hw_devname(devid) : NULL;
+}
+
+struct ath_hal *ath9k_hw_attach(u16 devid,
+ struct ath_softc *sc,
+ void __iomem *mem,
+ int *error)
+{
+ struct ath_hal *ah = NULL;
+
+ switch (devid) {
+ case AR5416_DEVID_PCI:
+ case AR5416_DEVID_PCIE:
+ case AR9160_DEVID_PCI:
+ case AR9280_DEVID_PCI:
+ case AR9280_DEVID_PCIE:
+ ah = ath9k_hw_do_attach(devid, sc, mem, error);
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_ANY,
+ "devid=0x%x not supported.\n", devid);
+ ah = NULL;
+ *error = -ENXIO;
+ break;
+ }
+ if (ah != NULL) {
+ ah->ah_devid = ah->ah_devid;
+ ah->ah_subvendorid = ah->ah_subvendorid;
+ ah->ah_macVersion = ah->ah_macVersion;
+ ah->ah_macRev = ah->ah_macRev;
+ ah->ah_phyRev = ah->ah_phyRev;
+ ah->ah_analog5GhzRev = ah->ah_analog5GhzRev;
+ ah->ah_analog2GhzRev = ah->ah_analog2GhzRev;
+ }
+ return ah;
+}
+
+u16
+ath9k_hw_computetxtime(struct ath_hal *ah,
+ const struct ath9k_rate_table *rates,
+ u32 frameLen, u16 rateix,
+ bool shortPreamble)
+{
+ u32 bitsPerSymbol, numBits, numSymbols, phyTime, txTime;
+ u32 kbps;
+
+ kbps = rates->info[rateix].rateKbps;
+
+ if (kbps == 0)
+ return 0;
+ switch (rates->info[rateix].phy) {
+
+ case PHY_CCK:
+ phyTime = CCK_PREAMBLE_BITS + CCK_PLCP_BITS;
+ if (shortPreamble && rates->info[rateix].shortPreamble)
+ phyTime >>= 1;
+ numBits = frameLen << 3;
+ txTime = CCK_SIFS_TIME + phyTime
+ + ((numBits * 1000) / kbps);
+ break;
+ case PHY_OFDM:
+ if (ah->ah_curchan && IS_CHAN_QUARTER_RATE(ah->ah_curchan)) {
+ bitsPerSymbol =
+ (kbps * OFDM_SYMBOL_TIME_QUARTER) / 1000;
+
+ numBits = OFDM_PLCP_BITS + (frameLen << 3);
+ numSymbols = DIV_ROUND_UP(numBits, bitsPerSymbol);
+ txTime = OFDM_SIFS_TIME_QUARTER
+ + OFDM_PREAMBLE_TIME_QUARTER
+ + (numSymbols * OFDM_SYMBOL_TIME_QUARTER);
+ } else if (ah->ah_curchan &&
+ IS_CHAN_HALF_RATE(ah->ah_curchan)) {
+ bitsPerSymbol =
+ (kbps * OFDM_SYMBOL_TIME_HALF) / 1000;
+
+ numBits = OFDM_PLCP_BITS + (frameLen << 3);
+ numSymbols = DIV_ROUND_UP(numBits, bitsPerSymbol);
+ txTime = OFDM_SIFS_TIME_HALF +
+ OFDM_PREAMBLE_TIME_HALF
+ + (numSymbols * OFDM_SYMBOL_TIME_HALF);
+ } else {
+ bitsPerSymbol = (kbps * OFDM_SYMBOL_TIME) / 1000;
+
+ numBits = OFDM_PLCP_BITS + (frameLen << 3);
+ numSymbols = DIV_ROUND_UP(numBits, bitsPerSymbol);
+ txTime = OFDM_SIFS_TIME + OFDM_PREAMBLE_TIME
+ + (numSymbols * OFDM_SYMBOL_TIME);
+ }
+ break;
+
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_PHY_IO,
+ "%s: unknown phy %u (rate ix %u)\n", __func__,
+ rates->info[rateix].phy, rateix);
+ txTime = 0;
+ break;
+ }
+ return txTime;
+}
+
+u32 ath9k_hw_mhz2ieee(struct ath_hal *ah, u32 freq, u32 flags)
+{
+ if (flags & CHANNEL_2GHZ) {
+ if (freq == 2484)
+ return 14;
+ if (freq < 2484)
+ return (freq - 2407) / 5;
+ else
+ return 15 + ((freq - 2512) / 20);
+ } else if (flags & CHANNEL_5GHZ) {
+ if (ath9k_regd_is_public_safety_sku(ah) &&
+ IS_CHAN_IN_PUBLIC_SAFETY_BAND(freq)) {
+ return ((freq * 10) +
+ (((freq % 5) == 2) ? 5 : 0) - 49400) / 5;
+ } else if ((flags & CHANNEL_A) && (freq <= 5000)) {
+ return (freq - 4000) / 5;
+ } else {
+ return (freq - 5000) / 5;
+ }
+ } else {
+ if (freq == 2484)
+ return 14;
+ if (freq < 2484)
+ return (freq - 2407) / 5;
+ if (freq < 5000) {
+ if (ath9k_regd_is_public_safety_sku(ah)
+ && IS_CHAN_IN_PUBLIC_SAFETY_BAND(freq)) {
+ return ((freq * 10) +
+ (((freq % 5) ==
+ 2) ? 5 : 0) - 49400) / 5;
+ } else if (freq > 4900) {
+ return (freq - 4000) / 5;
+ } else {
+ return 15 + ((freq - 2512) / 20);
+ }
+ }
+ return (freq - 5000) / 5;
+ }
+}
+
+int16_t
+ath9k_hw_getchan_noise(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ struct ath9k_channel *ichan;
+
+ ichan = ath9k_regd_check_channel(ah, chan);
+ if (ichan == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_NF_CAL,
+ "%s: invalid channel %u/0x%x; no mapping\n",
+ __func__, chan->channel, chan->channelFlags);
+ return 0;
+ }
+ if (ichan->rawNoiseFloor == 0) {
+ enum wireless_mode mode = ath9k_hw_chan2wmode(ah, chan);
+ return NOISE_FLOOR[mode];
+ } else
+ return ichan->rawNoiseFloor;
+}
+
+bool ath9k_hw_set_tsfadjust(struct ath_hal *ah, u32 setting)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (setting)
+ ahp->ah_miscMode |= AR_PCU_TX_ADD_TSF;
+ else
+ ahp->ah_miscMode &= ~AR_PCU_TX_ADD_TSF;
+ return true;
+}
+
+bool ath9k_hw_phycounters(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ return ahp->ah_hasHwPhyCounters ? true : false;
+}
+
+u32 ath9k_hw_gettxbuf(struct ath_hal *ah, u32 q)
+{
+ return REG_READ(ah, AR_QTXDP(q));
+}
+
+bool ath9k_hw_puttxbuf(struct ath_hal *ah, u32 q,
+ u32 txdp)
+{
+ REG_WRITE(ah, AR_QTXDP(q), txdp);
+
+ return true;
+}
+
+bool ath9k_hw_txstart(struct ath_hal *ah, u32 q)
+{
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE, "%s: queue %u\n", __func__, q);
+
+ REG_WRITE(ah, AR_Q_TXE, 1 << q);
+
+ return true;
+}
+
+u32 ath9k_hw_numtxpending(struct ath_hal *ah, u32 q)
+{
+ u32 npend;
+
+ npend = REG_READ(ah, AR_QSTS(q)) & AR_Q_STS_PEND_FR_CNT;
+ if (npend == 0) {
+
+ if (REG_READ(ah, AR_Q_TXE) & (1 << q))
+ npend = 1;
+ }
+ return npend;
+}
+
+bool ath9k_hw_stoptxdma(struct ath_hal *ah, u32 q)
+{
+ u32 wait;
+
+ REG_WRITE(ah, AR_Q_TXD, 1 << q);
+
+ for (wait = 1000; wait != 0; wait--) {
+ if (ath9k_hw_numtxpending(ah, q) == 0)
+ break;
+ udelay(100);
+ }
+
+ if (ath9k_hw_numtxpending(ah, q)) {
+ u32 tsfLow, j;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: Num of pending TX Frames %d on Q %d\n",
+ __func__, ath9k_hw_numtxpending(ah, q), q);
+
+ for (j = 0; j < 2; j++) {
+ tsfLow = REG_READ(ah, AR_TSF_L32);
+ REG_WRITE(ah, AR_QUIET2,
+ SM(10, AR_QUIET2_QUIET_DUR));
+ REG_WRITE(ah, AR_QUIET_PERIOD, 100);
+ REG_WRITE(ah, AR_NEXT_QUIET_TIMER, tsfLow >> 10);
+ REG_SET_BIT(ah, AR_TIMER_MODE,
+ AR_QUIET_TIMER_EN);
+
+ if ((REG_READ(ah, AR_TSF_L32) >> 10) ==
+ (tsfLow >> 10)) {
+ break;
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_QUEUE,
+ "%s: TSF have moved while trying to set "
+ "quiet time TSF: 0x%08x\n",
+ __func__, tsfLow);
+ }
+
+ REG_SET_BIT(ah, AR_DIAG_SW, AR_DIAG_FORCE_CH_IDLE_HIGH);
+
+ udelay(200);
+ REG_CLR_BIT(ah, AR_TIMER_MODE, AR_QUIET_TIMER_EN);
+
+ wait = 1000;
+
+ while (ath9k_hw_numtxpending(ah, q)) {
+ if ((--wait) == 0) {
+ DPRINTF(ah->ah_sc, ATH_DBG_XMIT,
+ "%s: Failed to stop Tx DMA in 100 "
+ "msec after killing last frame\n",
+ __func__);
+ break;
+ }
+ udelay(100);
+ }
+
+ REG_CLR_BIT(ah, AR_DIAG_SW, AR_DIAG_FORCE_CH_IDLE_HIGH);
+ }
+
+ REG_WRITE(ah, AR_Q_TXD, 0);
+ return wait != 0;
+}
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef HW_H
+#define HW_H
+
+#include <linux/if_ether.h>
+#include <linux/delay.h>
+
+struct ar5416_desc {
+ u32 ds_link;
+ u32 ds_data;
+ u32 ds_ctl0;
+ u32 ds_ctl1;
+ union {
+ struct {
+ u32 ctl2;
+ u32 ctl3;
+ u32 ctl4;
+ u32 ctl5;
+ u32 ctl6;
+ u32 ctl7;
+ u32 ctl8;
+ u32 ctl9;
+ u32 ctl10;
+ u32 ctl11;
+ u32 status0;
+ u32 status1;
+ u32 status2;
+ u32 status3;
+ u32 status4;
+ u32 status5;
+ u32 status6;
+ u32 status7;
+ u32 status8;
+ u32 status9;
+ } tx;
+ struct {
+ u32 status0;
+ u32 status1;
+ u32 status2;
+ u32 status3;
+ u32 status4;
+ u32 status5;
+ u32 status6;
+ u32 status7;
+ u32 status8;
+ } rx;
+ } u;
+} __packed;
+
+#define AR5416DESC(_ds) ((struct ar5416_desc *)(_ds))
+#define AR5416DESC_CONST(_ds) ((const struct ar5416_desc *)(_ds))
+
+#define ds_ctl2 u.tx.ctl2
+#define ds_ctl3 u.tx.ctl3
+#define ds_ctl4 u.tx.ctl4
+#define ds_ctl5 u.tx.ctl5
+#define ds_ctl6 u.tx.ctl6
+#define ds_ctl7 u.tx.ctl7
+#define ds_ctl8 u.tx.ctl8
+#define ds_ctl9 u.tx.ctl9
+#define ds_ctl10 u.tx.ctl10
+#define ds_ctl11 u.tx.ctl11
+
+#define ds_txstatus0 u.tx.status0
+#define ds_txstatus1 u.tx.status1
+#define ds_txstatus2 u.tx.status2
+#define ds_txstatus3 u.tx.status3
+#define ds_txstatus4 u.tx.status4
+#define ds_txstatus5 u.tx.status5
+#define ds_txstatus6 u.tx.status6
+#define ds_txstatus7 u.tx.status7
+#define ds_txstatus8 u.tx.status8
+#define ds_txstatus9 u.tx.status9
+
+#define ds_rxstatus0 u.rx.status0
+#define ds_rxstatus1 u.rx.status1
+#define ds_rxstatus2 u.rx.status2
+#define ds_rxstatus3 u.rx.status3
+#define ds_rxstatus4 u.rx.status4
+#define ds_rxstatus5 u.rx.status5
+#define ds_rxstatus6 u.rx.status6
+#define ds_rxstatus7 u.rx.status7
+#define ds_rxstatus8 u.rx.status8
+
+#define AR_FrameLen 0x00000fff
+#define AR_VirtMoreFrag 0x00001000
+#define AR_TxCtlRsvd00 0x0000e000
+#define AR_XmitPower 0x003f0000
+#define AR_XmitPower_S 16
+#define AR_RTSEnable 0x00400000
+#define AR_VEOL 0x00800000
+#define AR_ClrDestMask 0x01000000
+#define AR_TxCtlRsvd01 0x1e000000
+#define AR_TxIntrReq 0x20000000
+#define AR_DestIdxValid 0x40000000
+#define AR_CTSEnable 0x80000000
+
+#define AR_BufLen 0x00000fff
+#define AR_TxMore 0x00001000
+#define AR_DestIdx 0x000fe000
+#define AR_DestIdx_S 13
+#define AR_FrameType 0x00f00000
+#define AR_FrameType_S 20
+#define AR_NoAck 0x01000000
+#define AR_InsertTS 0x02000000
+#define AR_CorruptFCS 0x04000000
+#define AR_ExtOnly 0x08000000
+#define AR_ExtAndCtl 0x10000000
+#define AR_MoreAggr 0x20000000
+#define AR_IsAggr 0x40000000
+
+#define AR_BurstDur 0x00007fff
+#define AR_BurstDur_S 0
+#define AR_DurUpdateEna 0x00008000
+#define AR_XmitDataTries0 0x000f0000
+#define AR_XmitDataTries0_S 16
+#define AR_XmitDataTries1 0x00f00000
+#define AR_XmitDataTries1_S 20
+#define AR_XmitDataTries2 0x0f000000
+#define AR_XmitDataTries2_S 24
+#define AR_XmitDataTries3 0xf0000000
+#define AR_XmitDataTries3_S 28
+
+#define AR_XmitRate0 0x000000ff
+#define AR_XmitRate0_S 0
+#define AR_XmitRate1 0x0000ff00
+#define AR_XmitRate1_S 8
+#define AR_XmitRate2 0x00ff0000
+#define AR_XmitRate2_S 16
+#define AR_XmitRate3 0xff000000
+#define AR_XmitRate3_S 24
+
+#define AR_PacketDur0 0x00007fff
+#define AR_PacketDur0_S 0
+#define AR_RTSCTSQual0 0x00008000
+#define AR_PacketDur1 0x7fff0000
+#define AR_PacketDur1_S 16
+#define AR_RTSCTSQual1 0x80000000
+
+#define AR_PacketDur2 0x00007fff
+#define AR_PacketDur2_S 0
+#define AR_RTSCTSQual2 0x00008000
+#define AR_PacketDur3 0x7fff0000
+#define AR_PacketDur3_S 16
+#define AR_RTSCTSQual3 0x80000000
+
+#define AR_AggrLen 0x0000ffff
+#define AR_AggrLen_S 0
+#define AR_TxCtlRsvd60 0x00030000
+#define AR_PadDelim 0x03fc0000
+#define AR_PadDelim_S 18
+#define AR_EncrType 0x0c000000
+#define AR_EncrType_S 26
+#define AR_TxCtlRsvd61 0xf0000000
+
+#define AR_2040_0 0x00000001
+#define AR_GI0 0x00000002
+#define AR_ChainSel0 0x0000001c
+#define AR_ChainSel0_S 2
+#define AR_2040_1 0x00000020
+#define AR_GI1 0x00000040
+#define AR_ChainSel1 0x00000380
+#define AR_ChainSel1_S 7
+#define AR_2040_2 0x00000400
+#define AR_GI2 0x00000800
+#define AR_ChainSel2 0x00007000
+#define AR_ChainSel2_S 12
+#define AR_2040_3 0x00008000
+#define AR_GI3 0x00010000
+#define AR_ChainSel3 0x000e0000
+#define AR_ChainSel3_S 17
+#define AR_RTSCTSRate 0x0ff00000
+#define AR_RTSCTSRate_S 20
+#define AR_TxCtlRsvd70 0xf0000000
+
+#define AR_TxRSSIAnt00 0x000000ff
+#define AR_TxRSSIAnt00_S 0
+#define AR_TxRSSIAnt01 0x0000ff00
+#define AR_TxRSSIAnt01_S 8
+#define AR_TxRSSIAnt02 0x00ff0000
+#define AR_TxRSSIAnt02_S 16
+#define AR_TxStatusRsvd00 0x3f000000
+#define AR_TxBaStatus 0x40000000
+#define AR_TxStatusRsvd01 0x80000000
+
+#define AR_FrmXmitOK 0x00000001
+#define AR_ExcessiveRetries 0x00000002
+#define AR_FIFOUnderrun 0x00000004
+#define AR_Filtered 0x00000008
+#define AR_RTSFailCnt 0x000000f0
+#define AR_RTSFailCnt_S 4
+#define AR_DataFailCnt 0x00000f00
+#define AR_DataFailCnt_S 8
+#define AR_VirtRetryCnt 0x0000f000
+#define AR_VirtRetryCnt_S 12
+#define AR_TxDelimUnderrun 0x00010000
+#define AR_TxDataUnderrun 0x00020000
+#define AR_DescCfgErr 0x00040000
+#define AR_TxTimerExpired 0x00080000
+#define AR_TxStatusRsvd10 0xfff00000
+
+#define AR_SendTimestamp ds_txstatus2
+#define AR_BaBitmapLow ds_txstatus3
+#define AR_BaBitmapHigh ds_txstatus4
+
+#define AR_TxRSSIAnt10 0x000000ff
+#define AR_TxRSSIAnt10_S 0
+#define AR_TxRSSIAnt11 0x0000ff00
+#define AR_TxRSSIAnt11_S 8
+#define AR_TxRSSIAnt12 0x00ff0000
+#define AR_TxRSSIAnt12_S 16
+#define AR_TxRSSICombined 0xff000000
+#define AR_TxRSSICombined_S 24
+
+#define AR_TxEVM0 ds_txstatus5
+#define AR_TxEVM1 ds_txstatus6
+#define AR_TxEVM2 ds_txstatus7
+
+#define AR_TxDone 0x00000001
+#define AR_SeqNum 0x00001ffe
+#define AR_SeqNum_S 1
+#define AR_TxStatusRsvd80 0x0001e000
+#define AR_TxOpExceeded 0x00020000
+#define AR_TxStatusRsvd81 0x001c0000
+#define AR_FinalTxIdx 0x00600000
+#define AR_FinalTxIdx_S 21
+#define AR_TxStatusRsvd82 0x01800000
+#define AR_PowerMgmt 0x02000000
+#define AR_TxStatusRsvd83 0xfc000000
+
+#define AR_RxCTLRsvd00 0xffffffff
+
+#define AR_BufLen 0x00000fff
+#define AR_RxCtlRsvd00 0x00001000
+#define AR_RxIntrReq 0x00002000
+#define AR_RxCtlRsvd01 0xffffc000
+
+#define AR_RxRSSIAnt00 0x000000ff
+#define AR_RxRSSIAnt00_S 0
+#define AR_RxRSSIAnt01 0x0000ff00
+#define AR_RxRSSIAnt01_S 8
+#define AR_RxRSSIAnt02 0x00ff0000
+#define AR_RxRSSIAnt02_S 16
+#define AR_RxRate 0xff000000
+#define AR_RxRate_S 24
+#define AR_RxStatusRsvd00 0xff000000
+
+#define AR_DataLen 0x00000fff
+#define AR_RxMore 0x00001000
+#define AR_NumDelim 0x003fc000
+#define AR_NumDelim_S 14
+#define AR_RxStatusRsvd10 0xff800000
+
+#define AR_RcvTimestamp ds_rxstatus2
+
+#define AR_GI 0x00000001
+#define AR_2040 0x00000002
+#define AR_Parallel40 0x00000004
+#define AR_Parallel40_S 2
+#define AR_RxStatusRsvd30 0x000000f8
+#define AR_RxAntenna 0xffffff00
+#define AR_RxAntenna_S 8
+
+#define AR_RxRSSIAnt10 0x000000ff
+#define AR_RxRSSIAnt10_S 0
+#define AR_RxRSSIAnt11 0x0000ff00
+#define AR_RxRSSIAnt11_S 8
+#define AR_RxRSSIAnt12 0x00ff0000
+#define AR_RxRSSIAnt12_S 16
+#define AR_RxRSSICombined 0xff000000
+#define AR_RxRSSICombined_S 24
+
+#define AR_RxEVM0 ds_rxstatus4
+#define AR_RxEVM1 ds_rxstatus5
+#define AR_RxEVM2 ds_rxstatus6
+
+#define AR_RxDone 0x00000001
+#define AR_RxFrameOK 0x00000002
+#define AR_CRCErr 0x00000004
+#define AR_DecryptCRCErr 0x00000008
+#define AR_PHYErr 0x00000010
+#define AR_MichaelErr 0x00000020
+#define AR_PreDelimCRCErr 0x00000040
+#define AR_RxStatusRsvd70 0x00000080
+#define AR_RxKeyIdxValid 0x00000100
+#define AR_KeyIdx 0x0000fe00
+#define AR_KeyIdx_S 9
+#define AR_PHYErrCode 0x0000ff00
+#define AR_PHYErrCode_S 8
+#define AR_RxMoreAggr 0x00010000
+#define AR_RxAggr 0x00020000
+#define AR_PostDelimCRCErr 0x00040000
+#define AR_RxStatusRsvd71 0x3ff80000
+#define AR_DecryptBusyErr 0x40000000
+#define AR_KeyMiss 0x80000000
+
+#define AR5416_MAGIC 0x19641014
+
+#define RXSTATUS_RATE(ah, ads) (AR_SREV_5416_V20_OR_LATER(ah) ? \
+ MS(ads->ds_rxstatus0, AR_RxRate) : \
+ (ads->ds_rxstatus3 >> 2) & 0xFF)
+#define RXSTATUS_DUPLICATE(ah, ads) (AR_SREV_5416_V20_OR_LATER(ah) ? \
+ MS(ads->ds_rxstatus3, AR_Parallel40) : \
+ (ads->ds_rxstatus3 >> 10) & 0x1)
+
+#define set11nTries(_series, _index) \
+ (SM((_series)[_index].Tries, AR_XmitDataTries##_index))
+
+#define set11nRate(_series, _index) \
+ (SM((_series)[_index].Rate, AR_XmitRate##_index))
+
+#define set11nPktDurRTSCTS(_series, _index) \
+ (SM((_series)[_index].PktDuration, AR_PacketDur##_index) | \
+ ((_series)[_index].RateFlags & ATH9K_RATESERIES_RTS_CTS ? \
+ AR_RTSCTSQual##_index : 0))
+
+#define set11nRateFlags(_series, _index) \
+ (((_series)[_index].RateFlags & ATH9K_RATESERIES_2040 ? \
+ AR_2040_##_index : 0) \
+ |((_series)[_index].RateFlags & ATH9K_RATESERIES_HALFGI ? \
+ AR_GI##_index : 0) \
+ |SM((_series)[_index].ChSel, AR_ChainSel##_index))
+
+#define AR_SREV_9100(ah) ((ah->ah_macVersion) == AR_SREV_VERSION_9100)
+
+#define INIT_CONFIG_STATUS 0x00000000
+#define INIT_RSSI_THR 0x00000700
+#define INIT_BCON_CNTRL_REG 0x00000000
+
+#define MIN_TX_FIFO_THRESHOLD 0x1
+#define MAX_TX_FIFO_THRESHOLD ((4096 / 64) - 1)
+#define INIT_TX_FIFO_THRESHOLD MIN_TX_FIFO_THRESHOLD
+
+#define NUM_CORNER_FIX_BITS_2133 7
+#define CCK_OFDM_GAIN_DELTA 15
+
+struct ar5416AniState {
+ struct ath9k_channel c;
+ u8 noiseImmunityLevel;
+ u8 spurImmunityLevel;
+ u8 firstepLevel;
+ u8 ofdmWeakSigDetectOff;
+ u8 cckWeakSigThreshold;
+ u32 listenTime;
+ u32 ofdmTrigHigh;
+ u32 ofdmTrigLow;
+ int32_t cckTrigHigh;
+ int32_t cckTrigLow;
+ int32_t rssiThrLow;
+ int32_t rssiThrHigh;
+ u32 noiseFloor;
+ u32 txFrameCount;
+ u32 rxFrameCount;
+ u32 cycleCount;
+ u32 ofdmPhyErrCount;
+ u32 cckPhyErrCount;
+ u32 ofdmPhyErrBase;
+ u32 cckPhyErrBase;
+ int16_t pktRssi[2];
+ int16_t ofdmErrRssi[2];
+ int16_t cckErrRssi[2];
+};
+
+#define HAL_PROCESS_ANI 0x00000001
+#define HAL_RADAR_EN 0x80000000
+#define HAL_AR_EN 0x40000000
+
+#define DO_ANI(ah) \
+ ((AH5416(ah)->ah_procPhyErr & HAL_PROCESS_ANI))
+
+struct ar5416Stats {
+ u32 ast_ani_niup;
+ u32 ast_ani_nidown;
+ u32 ast_ani_spurup;
+ u32 ast_ani_spurdown;
+ u32 ast_ani_ofdmon;
+ u32 ast_ani_ofdmoff;
+ u32 ast_ani_cckhigh;
+ u32 ast_ani_ccklow;
+ u32 ast_ani_stepup;
+ u32 ast_ani_stepdown;
+ u32 ast_ani_ofdmerrs;
+ u32 ast_ani_cckerrs;
+ u32 ast_ani_reset;
+ u32 ast_ani_lzero;
+ u32 ast_ani_lneg;
+ struct ath9k_mib_stats ast_mibstats;
+ struct ath9k_node_stats ast_nodestats;
+};
+
+#define AR5416_OPFLAGS_11A 0x01
+#define AR5416_OPFLAGS_11G 0x02
+#define AR5416_OPFLAGS_N_5G_HT40 0x04
+#define AR5416_OPFLAGS_N_2G_HT40 0x08
+#define AR5416_OPFLAGS_N_5G_HT20 0x10
+#define AR5416_OPFLAGS_N_2G_HT20 0x20
+
+#define EEP_RFSILENT_ENABLED 0x0001
+#define EEP_RFSILENT_ENABLED_S 0
+#define EEP_RFSILENT_POLARITY 0x0002
+#define EEP_RFSILENT_POLARITY_S 1
+#define EEP_RFSILENT_GPIO_SEL 0x001c
+#define EEP_RFSILENT_GPIO_SEL_S 2
+
+#define AR5416_EEP_NO_BACK_VER 0x1
+#define AR5416_EEP_VER 0xE
+#define AR5416_EEP_VER_MINOR_MASK 0x0FFF
+#define AR5416_EEP_MINOR_VER_2 0x2
+#define AR5416_EEP_MINOR_VER_3 0x3
+#define AR5416_EEP_MINOR_VER_7 0x7
+#define AR5416_EEP_MINOR_VER_9 0x9
+
+#define AR5416_EEP_START_LOC 256
+#define AR5416_NUM_5G_CAL_PIERS 8
+#define AR5416_NUM_2G_CAL_PIERS 4
+#define AR5416_NUM_5G_20_TARGET_POWERS 8
+#define AR5416_NUM_5G_40_TARGET_POWERS 8
+#define AR5416_NUM_2G_CCK_TARGET_POWERS 3
+#define AR5416_NUM_2G_20_TARGET_POWERS 4
+#define AR5416_NUM_2G_40_TARGET_POWERS 4
+#define AR5416_NUM_CTLS 24
+#define AR5416_NUM_BAND_EDGES 8
+#define AR5416_NUM_PD_GAINS 4
+#define AR5416_PD_GAINS_IN_MASK 4
+#define AR5416_PD_GAIN_ICEPTS 5
+#define AR5416_EEPROM_MODAL_SPURS 5
+#define AR5416_MAX_RATE_POWER 63
+#define AR5416_NUM_PDADC_VALUES 128
+#define AR5416_NUM_RATES 16
+#define AR5416_BCHAN_UNUSED 0xFF
+#define AR5416_MAX_PWR_RANGE_IN_HALF_DB 64
+#define AR5416_EEPMISC_BIG_ENDIAN 0x01
+#define AR5416_MAX_CHAINS 3
+#define AR5416_ANT_16S 25
+
+#define AR5416_NUM_ANT_CHAIN_FIELDS 7
+#define AR5416_NUM_ANT_COMMON_FIELDS 4
+#define AR5416_SIZE_ANT_CHAIN_FIELD 3
+#define AR5416_SIZE_ANT_COMMON_FIELD 4
+#define AR5416_ANT_CHAIN_MASK 0x7
+#define AR5416_ANT_COMMON_MASK 0xf
+#define AR5416_CHAIN_0_IDX 0
+#define AR5416_CHAIN_1_IDX 1
+#define AR5416_CHAIN_2_IDX 2
+
+#define AR5416_PWR_TABLE_OFFSET -5
+#define AR5416_LEGACY_CHAINMASK 1
+
+enum eeprom_param {
+ EEP_NFTHRESH_5,
+ EEP_NFTHRESH_2,
+ EEP_MAC_MSW,
+ EEP_MAC_MID,
+ EEP_MAC_LSW,
+ EEP_REG_0,
+ EEP_REG_1,
+ EEP_OP_CAP,
+ EEP_OP_MODE,
+ EEP_RF_SILENT,
+ EEP_OB_5,
+ EEP_DB_5,
+ EEP_OB_2,
+ EEP_DB_2,
+ EEP_MINOR_REV,
+ EEP_TX_MASK,
+ EEP_RX_MASK,
+};
+
+enum ar5416_rates {
+ rate6mb, rate9mb, rate12mb, rate18mb,
+ rate24mb, rate36mb, rate48mb, rate54mb,
+ rate1l, rate2l, rate2s, rate5_5l,
+ rate5_5s, rate11l, rate11s, rateXr,
+ rateHt20_0, rateHt20_1, rateHt20_2, rateHt20_3,
+ rateHt20_4, rateHt20_5, rateHt20_6, rateHt20_7,
+ rateHt40_0, rateHt40_1, rateHt40_2, rateHt40_3,
+ rateHt40_4, rateHt40_5, rateHt40_6, rateHt40_7,
+ rateDupCck, rateDupOfdm, rateExtCck, rateExtOfdm,
+ Ar5416RateSize
+};
+
+struct base_eep_header {
+ u16 length;
+ u16 checksum;
+ u16 version;
+ u8 opCapFlags;
+ u8 eepMisc;
+ u16 regDmn[2];
+ u8 macAddr[6];
+ u8 rxMask;
+ u8 txMask;
+ u16 rfSilent;
+ u16 blueToothOptions;
+ u16 deviceCap;
+ u32 binBuildNumber;
+ u8 deviceType;
+ u8 pwdclkind;
+ u8 futureBase[32];
+} __packed;
+
+struct spur_chan {
+ u16 spurChan;
+ u8 spurRangeLow;
+ u8 spurRangeHigh;
+} __packed;
+
+struct modal_eep_header {
+ u32 antCtrlChain[AR5416_MAX_CHAINS];
+ u32 antCtrlCommon;
+ u8 antennaGainCh[AR5416_MAX_CHAINS];
+ u8 switchSettling;
+ u8 txRxAttenCh[AR5416_MAX_CHAINS];
+ u8 rxTxMarginCh[AR5416_MAX_CHAINS];
+ u8 adcDesiredSize;
+ u8 pgaDesiredSize;
+ u8 xlnaGainCh[AR5416_MAX_CHAINS];
+ u8 txEndToXpaOff;
+ u8 txEndToRxOn;
+ u8 txFrameToXpaOn;
+ u8 thresh62;
+ u8 noiseFloorThreshCh[AR5416_MAX_CHAINS];
+ u8 xpdGain;
+ u8 xpd;
+ u8 iqCalICh[AR5416_MAX_CHAINS];
+ u8 iqCalQCh[AR5416_MAX_CHAINS];
+ u8 pdGainOverlap;
+ u8 ob;
+ u8 db;
+ u8 xpaBiasLvl;
+ u8 pwrDecreaseFor2Chain;
+ u8 pwrDecreaseFor3Chain;
+ u8 txFrameToDataStart;
+ u8 txFrameToPaOn;
+ u8 ht40PowerIncForPdadc;
+ u8 bswAtten[AR5416_MAX_CHAINS];
+ u8 bswMargin[AR5416_MAX_CHAINS];
+ u8 swSettleHt40;
+ u8 xatten2Db[AR5416_MAX_CHAINS];
+ u8 xatten2Margin[AR5416_MAX_CHAINS];
+ u8 ob_ch1;
+ u8 db_ch1;
+ u8 useAnt1:1,
+ force_xpaon:1,
+ local_bias:1,
+ femBandSelectUsed:1, xlnabufin:1, xlnaisel:2, xlnabufmode:1;
+ u8 futureModalar9280;
+ u16 xpaBiasLvlFreq[3];
+ u8 futureModal[6];
+
+ struct spur_chan spurChans[AR5416_EEPROM_MODAL_SPURS];
+} __packed;
+
+struct cal_data_per_freq {
+ u8 pwrPdg[AR5416_NUM_PD_GAINS][AR5416_PD_GAIN_ICEPTS];
+ u8 vpdPdg[AR5416_NUM_PD_GAINS][AR5416_PD_GAIN_ICEPTS];
+} __packed;
+
+struct cal_target_power_leg {
+ u8 bChannel;
+ u8 tPow2x[4];
+} __packed;
+
+struct cal_target_power_ht {
+ u8 bChannel;
+ u8 tPow2x[8];
+} __packed;
+
+#ifdef __BIG_ENDIAN_BITFIELD
+struct cal_ctl_edges {
+ u8 bChannel;
+ u8 flag:2, tPower:6;
+} __packed;
+#else
+struct cal_ctl_edges {
+ u8 bChannel;
+ u8 tPower:6, flag:2;
+} __packed;
+#endif
+
+struct cal_ctl_data {
+ struct cal_ctl_edges
+ ctlEdges[AR5416_MAX_CHAINS][AR5416_NUM_BAND_EDGES];
+} __packed;
+
+struct ar5416_eeprom {
+ struct base_eep_header baseEepHeader;
+ u8 custData[64];
+ struct modal_eep_header modalHeader[2];
+ u8 calFreqPier5G[AR5416_NUM_5G_CAL_PIERS];
+ u8 calFreqPier2G[AR5416_NUM_2G_CAL_PIERS];
+ struct cal_data_per_freq
+ calPierData5G[AR5416_MAX_CHAINS][AR5416_NUM_5G_CAL_PIERS];
+ struct cal_data_per_freq
+ calPierData2G[AR5416_MAX_CHAINS][AR5416_NUM_2G_CAL_PIERS];
+ struct cal_target_power_leg
+ calTargetPower5G[AR5416_NUM_5G_20_TARGET_POWERS];
+ struct cal_target_power_ht
+ calTargetPower5GHT20[AR5416_NUM_5G_20_TARGET_POWERS];
+ struct cal_target_power_ht
+ calTargetPower5GHT40[AR5416_NUM_5G_40_TARGET_POWERS];
+ struct cal_target_power_leg
+ calTargetPowerCck[AR5416_NUM_2G_CCK_TARGET_POWERS];
+ struct cal_target_power_leg
+ calTargetPower2G[AR5416_NUM_2G_20_TARGET_POWERS];
+ struct cal_target_power_ht
+ calTargetPower2GHT20[AR5416_NUM_2G_20_TARGET_POWERS];
+ struct cal_target_power_ht
+ calTargetPower2GHT40[AR5416_NUM_2G_40_TARGET_POWERS];
+ u8 ctlIndex[AR5416_NUM_CTLS];
+ struct cal_ctl_data ctlData[AR5416_NUM_CTLS];
+ u8 padding;
+} __packed;
+
+struct ar5416IniArray {
+ u32 *ia_array;
+ u32 ia_rows;
+ u32 ia_columns;
+};
+
+#define INIT_INI_ARRAY(iniarray, array, rows, columns) do { \
+ (iniarray)->ia_array = (u32 *)(array); \
+ (iniarray)->ia_rows = (rows); \
+ (iniarray)->ia_columns = (columns); \
+ } while (0)
+
+#define INI_RA(iniarray, row, column) \
+ (((iniarray)->ia_array)[(row) * ((iniarray)->ia_columns) + (column)])
+
+#define INIT_CAL(_perCal) do { \
+ (_perCal)->calState = CAL_WAITING; \
+ (_perCal)->calNext = NULL; \
+ } while (0)
+
+#define INSERT_CAL(_ahp, _perCal) \
+ do { \
+ if ((_ahp)->ah_cal_list_last == NULL) { \
+ (_ahp)->ah_cal_list = \
+ (_ahp)->ah_cal_list_last = (_perCal); \
+ ((_ahp)->ah_cal_list_last)->calNext = (_perCal); \
+ } else { \
+ ((_ahp)->ah_cal_list_last)->calNext = (_perCal); \
+ (_ahp)->ah_cal_list_last = (_perCal); \
+ (_perCal)->calNext = (_ahp)->ah_cal_list; \
+ } \
+ } while (0)
+
+enum hal_cal_types {
+ ADC_DC_INIT_CAL = 0x1,
+ ADC_GAIN_CAL = 0x2,
+ ADC_DC_CAL = 0x4,
+ IQ_MISMATCH_CAL = 0x8
+};
+
+enum hal_cal_state {
+ CAL_INACTIVE,
+ CAL_WAITING,
+ CAL_RUNNING,
+ CAL_DONE
+};
+
+#define MIN_CAL_SAMPLES 1
+#define MAX_CAL_SAMPLES 64
+#define INIT_LOG_COUNT 5
+#define PER_MIN_LOG_COUNT 2
+#define PER_MAX_LOG_COUNT 10
+
+struct hal_percal_data {
+ enum hal_cal_types calType;
+ u32 calNumSamples;
+ u32 calCountMax;
+ void (*calCollect) (struct ath_hal *);
+ void (*calPostProc) (struct ath_hal *, u8);
+};
+
+struct hal_cal_list {
+ const struct hal_percal_data *calData;
+ enum hal_cal_state calState;
+ struct hal_cal_list *calNext;
+};
+
+struct ath_hal_5416 {
+ struct ath_hal ah;
+ struct ar5416_eeprom ah_eeprom;
+ u8 ah_macaddr[ETH_ALEN];
+ u8 ah_bssid[ETH_ALEN];
+ u8 ah_bssidmask[ETH_ALEN];
+ u16 ah_assocId;
+ int16_t ah_curchanRadIndex;
+ u32 ah_maskReg;
+ struct ar5416Stats ah_stats;
+ u32 ah_txDescMask;
+ u32 ah_txOkInterruptMask;
+ u32 ah_txErrInterruptMask;
+ u32 ah_txDescInterruptMask;
+ u32 ah_txEolInterruptMask;
+ u32 ah_txUrnInterruptMask;
+ struct ath9k_tx_queue_info ah_txq[ATH9K_NUM_TX_QUEUES];
+ enum ath9k_power_mode ah_powerMode;
+ bool ah_chipFullSleep;
+ u32 ah_atimWindow;
+ enum ath9k_ant_setting ah_diversityControl;
+ u16 ah_antennaSwitchSwap;
+ enum hal_cal_types ah_suppCals;
+ struct hal_cal_list ah_iqCalData;
+ struct hal_cal_list ah_adcGainCalData;
+ struct hal_cal_list ah_adcDcCalInitData;
+ struct hal_cal_list ah_adcDcCalData;
+ struct hal_cal_list *ah_cal_list;
+ struct hal_cal_list *ah_cal_list_last;
+ struct hal_cal_list *ah_cal_list_curr;
+#define ah_totalPowerMeasI ah_Meas0.unsign
+#define ah_totalPowerMeasQ ah_Meas1.unsign
+#define ah_totalIqCorrMeas ah_Meas2.sign
+#define ah_totalAdcIOddPhase ah_Meas0.unsign
+#define ah_totalAdcIEvenPhase ah_Meas1.unsign
+#define ah_totalAdcQOddPhase ah_Meas2.unsign
+#define ah_totalAdcQEvenPhase ah_Meas3.unsign
+#define ah_totalAdcDcOffsetIOddPhase ah_Meas0.sign
+#define ah_totalAdcDcOffsetIEvenPhase ah_Meas1.sign
+#define ah_totalAdcDcOffsetQOddPhase ah_Meas2.sign
+#define ah_totalAdcDcOffsetQEvenPhase ah_Meas3.sign
+ union {
+ u32 unsign[AR5416_MAX_CHAINS];
+ int32_t sign[AR5416_MAX_CHAINS];
+ } ah_Meas0;
+ union {
+ u32 unsign[AR5416_MAX_CHAINS];
+ int32_t sign[AR5416_MAX_CHAINS];
+ } ah_Meas1;
+ union {
+ u32 unsign[AR5416_MAX_CHAINS];
+ int32_t sign[AR5416_MAX_CHAINS];
+ } ah_Meas2;
+ union {
+ u32 unsign[AR5416_MAX_CHAINS];
+ int32_t sign[AR5416_MAX_CHAINS];
+ } ah_Meas3;
+ u16 ah_CalSamples;
+ u32 ah_tx6PowerInHalfDbm;
+ u32 ah_staId1Defaults;
+ u32 ah_miscMode;
+ bool ah_tpcEnabled;
+ u32 ah_beaconInterval;
+ enum {
+ AUTO_32KHZ,
+ USE_32KHZ,
+ DONT_USE_32KHZ,
+ } ah_enable32kHzClock;
+ u32 *ah_analogBank0Data;
+ u32 *ah_analogBank1Data;
+ u32 *ah_analogBank2Data;
+ u32 *ah_analogBank3Data;
+ u32 *ah_analogBank6Data;
+ u32 *ah_analogBank6TPCData;
+ u32 *ah_analogBank7Data;
+ u32 *ah_addac5416_21;
+ u32 *ah_bank6Temp;
+ u32 ah_ofdmTxPower;
+ int16_t ah_txPowerIndexOffset;
+ u32 ah_slottime;
+ u32 ah_acktimeout;
+ u32 ah_ctstimeout;
+ u32 ah_globaltxtimeout;
+ u8 ah_gBeaconRate;
+ u32 ah_gpioSelect;
+ u32 ah_polarity;
+ u32 ah_gpioBit;
+ bool ah_eepEnabled;
+ u32 ah_procPhyErr;
+ bool ah_hasHwPhyCounters;
+ u32 ah_aniPeriod;
+ struct ar5416AniState *ah_curani;
+ struct ar5416AniState ah_ani[255];
+ int ah_totalSizeDesired[5];
+ int ah_coarseHigh[5];
+ int ah_coarseLow[5];
+ int ah_firpwr[5];
+ u16 ah_ratesArray[16];
+ u32 ah_intrTxqs;
+ bool ah_intrMitigation;
+ u32 ah_cycleCount;
+ u32 ah_ctlBusy;
+ u32 ah_extBusy;
+ enum ath9k_ht_extprotspacing ah_extprotspacing;
+ u8 ah_txchainmask;
+ u8 ah_rxchainmask;
+ int ah_hwp;
+ void __iomem *ah_cal_mem;
+ enum ath9k_ani_cmd ah_ani_function;
+ struct ar5416IniArray ah_iniModes;
+ struct ar5416IniArray ah_iniCommon;
+ struct ar5416IniArray ah_iniBank0;
+ struct ar5416IniArray ah_iniBB_RfGain;
+ struct ar5416IniArray ah_iniBank1;
+ struct ar5416IniArray ah_iniBank2;
+ struct ar5416IniArray ah_iniBank3;
+ struct ar5416IniArray ah_iniBank6;
+ struct ar5416IniArray ah_iniBank6TPC;
+ struct ar5416IniArray ah_iniBank7;
+ struct ar5416IniArray ah_iniAddac;
+ struct ar5416IniArray ah_iniPcieSerdes;
+ struct ar5416IniArray ah_iniModesAdditional;
+};
+#define AH5416(_ah) ((struct ath_hal_5416 *)(_ah))
+
+#define FREQ2FBIN(x, y) ((y) ? ((x) - 2300) : (((x) - 4800) / 5))
+
+#define IS_5416_EMU(ah) \
+ ((ah->ah_devid == AR5416_DEVID_EMU) || \
+ (ah->ah_devid == AR5416_DEVID_EMU_PCIE))
+
+#define ar5416RfDetach(ah) do { \
+ if (AH5416(ah)->ah_rfHal.rfDetach != NULL) \
+ AH5416(ah)->ah_rfHal.rfDetach(ah); \
+ } while (0)
+
+#define ath9k_hw_use_flash(_ah) \
+ (!(_ah->ah_flags & AH_USE_EEPROM))
+
+
+#define DO_DELAY(x) do { \
+ if ((++(x) % 64) == 0) \
+ udelay(1); \
+ } while (0)
+
+#define REG_WRITE_ARRAY(iniarray, column, regWr) do { \
+ int r; \
+ for (r = 0; r < ((iniarray)->ia_rows); r++) { \
+ REG_WRITE(ah, INI_RA((iniarray), (r), 0), \
+ INI_RA((iniarray), r, (column))); \
+ DO_DELAY(regWr); \
+ } \
+ } while (0)
+
+#define BASE_ACTIVATE_DELAY 100
+#define RTC_PLL_SETTLE_DELAY 1000
+#define COEF_SCALE_S 24
+#define HT40_CHANNEL_CENTER_SHIFT 10
+
+#define ar5416CheckOpMode(_opmode) \
+ ((_opmode == ATH9K_M_STA) || (_opmode == ATH9K_M_IBSS) || \
+ (_opmode == ATH9K_M_HOSTAP) || (_opmode == ATH9K_M_MONITOR))
+
+#define AR5416_EEPROM_MAGIC_OFFSET 0x0
+
+#define AR5416_EEPROM_S 2
+#define AR5416_EEPROM_OFFSET 0x2000
+#define AR5416_EEPROM_START_ADDR \
+ (AR_SREV_9100(ah)) ? 0x1fff1000 : 0x503f1200
+#define AR5416_EEPROM_MAX 0xae0
+#define ar5416_get_eep_ver(_ahp) \
+ (((_ahp)->ah_eeprom.baseEepHeader.version >> 12) & 0xF)
+#define ar5416_get_eep_rev(_ahp) \
+ (((_ahp)->ah_eeprom.baseEepHeader.version) & 0xFFF)
+#define ar5416_get_ntxchains(_txchainmask) \
+ (((_txchainmask >> 2) & 1) + \
+ ((_txchainmask >> 1) & 1) + (_txchainmask & 1))
+
+#define IS_EEP_MINOR_V3(_ahp) \
+ (ath9k_hw_get_eeprom((_ahp), EEP_MINOR_REV) >= AR5416_EEP_MINOR_VER_3)
+
+#define FIXED_CCA_THRESHOLD 15
+
+#ifdef __BIG_ENDIAN
+#define AR5416_EEPROM_MAGIC 0x5aa5
+#else
+#define AR5416_EEPROM_MAGIC 0xa55a
+#endif
+
+#define ATH9K_POW_SM(_r, _s) (((_r) & 0x3f) << (_s))
+
+#define ATH9K_ANTENNA0_CHAINMASK 0x1
+#define ATH9K_ANTENNA1_CHAINMASK 0x2
+
+#define ATH9K_NUM_DMA_DEBUG_REGS 8
+#define ATH9K_NUM_QUEUES 10
+
+#define HAL_NOISE_IMMUNE_MAX 4
+#define HAL_SPUR_IMMUNE_MAX 7
+#define HAL_FIRST_STEP_MAX 2
+
+#define ATH9K_ANI_OFDM_TRIG_HIGH 500
+#define ATH9K_ANI_OFDM_TRIG_LOW 200
+#define ATH9K_ANI_CCK_TRIG_HIGH 200
+#define ATH9K_ANI_CCK_TRIG_LOW 100
+#define ATH9K_ANI_NOISE_IMMUNE_LVL 4
+#define ATH9K_ANI_USE_OFDM_WEAK_SIG true
+#define ATH9K_ANI_CCK_WEAK_SIG_THR false
+#define ATH9K_ANI_SPUR_IMMUNE_LVL 7
+#define ATH9K_ANI_FIRSTEP_LVL 0
+#define ATH9K_ANI_RSSI_THR_HIGH 40
+#define ATH9K_ANI_RSSI_THR_LOW 7
+#define ATH9K_ANI_PERIOD 100
+
+#define AR_GPIOD_MASK 0x00001FFF
+#define AR_GPIO_BIT(_gpio) (1 << (_gpio))
+
+#define MAX_ANALOG_START 319
+
+#define HAL_EP_RND(x, mul) \
+ ((((x)%(mul)) >= ((mul)/2)) ? ((x) + ((mul) - 1)) / (mul) : (x)/(mul))
+#define BEACON_RSSI(ahp) \
+ HAL_EP_RND(ahp->ah_stats.ast_nodestats.ns_avgbrssi, \
+ ATH9K_RSSI_EP_MULTIPLIER)
+
+#define ah_mibStats ah_stats.ast_mibstats
+
+#define AH_TIMEOUT 100000
+#define AH_TIME_QUANTUM 10
+
+#define IS(_c, _f) (((_c)->channelFlags & _f) || 0)
+
+#define AR_KEYTABLE_SIZE 128
+#define POWER_UP_TIME 200000
+
+#define EXT_ADDITIVE (0x8000)
+#define CTL_11A_EXT (CTL_11A | EXT_ADDITIVE)
+#define CTL_11G_EXT (CTL_11G | EXT_ADDITIVE)
+#define CTL_11B_EXT (CTL_11B | EXT_ADDITIVE)
+
+#define SUB_NUM_CTL_MODES_AT_5G_40 2
+#define SUB_NUM_CTL_MODES_AT_2G_40 3
+#define SPUR_RSSI_THRESH 40
+
+#define TU_TO_USEC(_tu) ((_tu) << 10)
+
+#define CAB_TIMEOUT_VAL 10
+#define BEACON_TIMEOUT_VAL 10
+#define MIN_BEACON_TIMEOUT_VAL 1
+#define SLEEP_SLOP 3
+
+#define CCK_SIFS_TIME 10
+#define CCK_PREAMBLE_BITS 144
+#define CCK_PLCP_BITS 48
+
+#define OFDM_SIFS_TIME 16
+#define OFDM_PREAMBLE_TIME 20
+#define OFDM_PLCP_BITS 22
+#define OFDM_SYMBOL_TIME 4
+
+#define OFDM_SIFS_TIME_HALF 32
+#define OFDM_PREAMBLE_TIME_HALF 40
+#define OFDM_PLCP_BITS_HALF 22
+#define OFDM_SYMBOL_TIME_HALF 8
+
+#define OFDM_SIFS_TIME_QUARTER 64
+#define OFDM_PREAMBLE_TIME_QUARTER 80
+#define OFDM_PLCP_BITS_QUARTER 22
+#define OFDM_SYMBOL_TIME_QUARTER 16
+
+u32 ath9k_hw_get_eeprom(struct ath_hal_5416 *ahp,
+ enum eeprom_param param);
+
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+static const u32 ar5416Modes_9100[][6] = {
+ { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 },
+ { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 },
+ { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 },
+ { 0x000010f0, 0x0000a000, 0x00014000, 0x00016000, 0x0000b000, 0x00014008 },
+ { 0x00008014, 0x03e803e8, 0x07d007d0, 0x10801600, 0x08400b00, 0x06e006e0 },
+ { 0x0000801c, 0x128d93a7, 0x128d93cf, 0x12e013d7, 0x12e013ab, 0x098813cf },
+ { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 },
+ { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 },
+ { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 },
+ { 0x00009844, 0x1372161e, 0x1372161e, 0x137216a0, 0x137216a0, 0x137216a0 },
+ { 0x00009848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000a848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000b848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x00009850, 0x6de8b4e0, 0x6de8b4e0, 0x6de8b0de, 0x6de8b0de, 0x6de8b0de },
+ { 0x00009858, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e },
+ { 0x0000985c, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e },
+ { 0x00009860, 0x00049d18, 0x00049d18, 0x00049d18, 0x00049d18, 0x00049d18 },
+ { 0x0000c864, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00 },
+ { 0x00009868, 0x409a4190, 0x409a4190, 0x409a4190, 0x409a4190, 0x409a4190 },
+ { 0x0000986c, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081 },
+ { 0x00009914, 0x000007d0, 0x000007d0, 0x00000898, 0x00000898, 0x000007d0 },
+ { 0x00009918, 0x000001b8, 0x00000370, 0x00000268, 0x00000134, 0x00000134 },
+ { 0x00009924, 0xd0058a0b, 0xd0058a0b, 0xd0058a0b, 0xd0058a0b, 0xd0058a0b },
+ { 0x00009944, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020 },
+ { 0x00009960, 0x00000900, 0x00000900, 0x00012d80, 0x00012d80, 0x00012d80 },
+ { 0x0000a960, 0x00000900, 0x00000900, 0x00012d80, 0x00012d80, 0x00012d80 },
+ { 0x0000b960, 0x00000900, 0x00000900, 0x00012d80, 0x00012d80, 0x00012d80 },
+ { 0x00009964, 0x00000000, 0x00000000, 0x00001120, 0x00001120, 0x00001120 },
+ { 0x0000c9bc, 0x001a0a00, 0x001a0a00, 0x001a0a00, 0x001a0a00, 0x001a0a00 },
+ { 0x000099c0, 0x038919be, 0x038919be, 0x038919be, 0x038919be, 0x038919be },
+ { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 },
+ { 0x000099c8, 0x60f6532c, 0x60f6532c, 0x60f6532c, 0x60f6532c, 0x60f6532c },
+ { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 },
+ { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 },
+ { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x000099d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a204, 0x00000880, 0x00000880, 0x00000880, 0x00000880, 0x00000880 },
+ { 0x0000a208, 0xd6be4788, 0xd6be4788, 0xd03e4788, 0xd03e4788, 0xd03e4788 },
+ { 0x0000a20c, 0x002ec1e0, 0x002ec1e0, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000b20c, 0x002ec1e0, 0x002ec1e0, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000c20c, 0x002ec1e0, 0x002ec1e0, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000a21c, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a },
+ { 0x0000a230, 0x00000000, 0x00000000, 0x00000210, 0x00000108, 0x00000000 },
+ { 0x0000a274, 0x0a1a9caa, 0x0a1a9caa, 0x0a1a7caa, 0x0a1a7caa, 0x0a1a7caa },
+ { 0x0000a300, 0x18010000, 0x18010000, 0x18010000, 0x18010000, 0x18010000 },
+ { 0x0000a304, 0x30032602, 0x30032602, 0x2e032402, 0x2e032402, 0x2e032402 },
+ { 0x0000a308, 0x48073e06, 0x48073e06, 0x4a0a3c06, 0x4a0a3c06, 0x4a0a3c06 },
+ { 0x0000a30c, 0x560b4c0a, 0x560b4c0a, 0x621a540b, 0x621a540b, 0x621a540b },
+ { 0x0000a310, 0x641a600f, 0x641a600f, 0x764f6c1b, 0x764f6c1b, 0x764f6c1b },
+ { 0x0000a314, 0x7a4f6e1b, 0x7a4f6e1b, 0x845b7a5a, 0x845b7a5a, 0x845b7a5a },
+ { 0x0000a318, 0x8c5b7e5a, 0x8c5b7e5a, 0x950f8ccf, 0x950f8ccf, 0x950f8ccf },
+ { 0x0000a31c, 0x9d0f96cf, 0x9d0f96cf, 0xa5cf9b4f, 0xa5cf9b4f, 0xa5cf9b4f },
+ { 0x0000a320, 0xb51fa69f, 0xb51fa69f, 0xbddfaf1f, 0xbddfaf1f, 0xbddfaf1f },
+ { 0x0000a324, 0xcb3fbd07, 0xcb3fbcbf, 0xd1ffc93f, 0xd1ffc93f, 0xd1ffc93f },
+ { 0x0000a328, 0x0000d7bf, 0x0000d7bf, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a32c, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a330, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a334, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+};
+
+static const u32 ar5416Common_9100[][2] = {
+ { 0x0000000c, 0x00000000 },
+ { 0x00000030, 0x00020015 },
+ { 0x00000034, 0x00000005 },
+ { 0x00000040, 0x00000000 },
+ { 0x00000044, 0x00000008 },
+ { 0x00000048, 0x00000008 },
+ { 0x0000004c, 0x00000010 },
+ { 0x00000050, 0x00000000 },
+ { 0x00000054, 0x0000001f },
+ { 0x00000800, 0x00000000 },
+ { 0x00000804, 0x00000000 },
+ { 0x00000808, 0x00000000 },
+ { 0x0000080c, 0x00000000 },
+ { 0x00000810, 0x00000000 },
+ { 0x00000814, 0x00000000 },
+ { 0x00000818, 0x00000000 },
+ { 0x0000081c, 0x00000000 },
+ { 0x00000820, 0x00000000 },
+ { 0x00000824, 0x00000000 },
+ { 0x00001040, 0x002ffc0f },
+ { 0x00001044, 0x002ffc0f },
+ { 0x00001048, 0x002ffc0f },
+ { 0x0000104c, 0x002ffc0f },
+ { 0x00001050, 0x002ffc0f },
+ { 0x00001054, 0x002ffc0f },
+ { 0x00001058, 0x002ffc0f },
+ { 0x0000105c, 0x002ffc0f },
+ { 0x00001060, 0x002ffc0f },
+ { 0x00001064, 0x002ffc0f },
+ { 0x00001230, 0x00000000 },
+ { 0x00001270, 0x00000000 },
+ { 0x00001038, 0x00000000 },
+ { 0x00001078, 0x00000000 },
+ { 0x000010b8, 0x00000000 },
+ { 0x000010f8, 0x00000000 },
+ { 0x00001138, 0x00000000 },
+ { 0x00001178, 0x00000000 },
+ { 0x000011b8, 0x00000000 },
+ { 0x000011f8, 0x00000000 },
+ { 0x00001238, 0x00000000 },
+ { 0x00001278, 0x00000000 },
+ { 0x000012b8, 0x00000000 },
+ { 0x000012f8, 0x00000000 },
+ { 0x00001338, 0x00000000 },
+ { 0x00001378, 0x00000000 },
+ { 0x000013b8, 0x00000000 },
+ { 0x000013f8, 0x00000000 },
+ { 0x00001438, 0x00000000 },
+ { 0x00001478, 0x00000000 },
+ { 0x000014b8, 0x00000000 },
+ { 0x000014f8, 0x00000000 },
+ { 0x00001538, 0x00000000 },
+ { 0x00001578, 0x00000000 },
+ { 0x000015b8, 0x00000000 },
+ { 0x000015f8, 0x00000000 },
+ { 0x00001638, 0x00000000 },
+ { 0x00001678, 0x00000000 },
+ { 0x000016b8, 0x00000000 },
+ { 0x000016f8, 0x00000000 },
+ { 0x00001738, 0x00000000 },
+ { 0x00001778, 0x00000000 },
+ { 0x000017b8, 0x00000000 },
+ { 0x000017f8, 0x00000000 },
+ { 0x0000103c, 0x00000000 },
+ { 0x0000107c, 0x00000000 },
+ { 0x000010bc, 0x00000000 },
+ { 0x000010fc, 0x00000000 },
+ { 0x0000113c, 0x00000000 },
+ { 0x0000117c, 0x00000000 },
+ { 0x000011bc, 0x00000000 },
+ { 0x000011fc, 0x00000000 },
+ { 0x0000123c, 0x00000000 },
+ { 0x0000127c, 0x00000000 },
+ { 0x000012bc, 0x00000000 },
+ { 0x000012fc, 0x00000000 },
+ { 0x0000133c, 0x00000000 },
+ { 0x0000137c, 0x00000000 },
+ { 0x000013bc, 0x00000000 },
+ { 0x000013fc, 0x00000000 },
+ { 0x0000143c, 0x00000000 },
+ { 0x0000147c, 0x00000000 },
+ { 0x00004030, 0x00000002 },
+ { 0x0000403c, 0x00000002 },
+ { 0x00007010, 0x00000000 },
+ { 0x00007038, 0x000004c2 },
+ { 0x00008004, 0x00000000 },
+ { 0x00008008, 0x00000000 },
+ { 0x0000800c, 0x00000000 },
+ { 0x00008018, 0x00000700 },
+ { 0x00008020, 0x00000000 },
+ { 0x00008038, 0x00000000 },
+ { 0x0000803c, 0x00000000 },
+ { 0x00008048, 0x40000000 },
+ { 0x00008054, 0x00000000 },
+ { 0x00008058, 0x00000000 },
+ { 0x0000805c, 0x000fc78f },
+ { 0x00008060, 0x0000000f },
+ { 0x00008064, 0x00000000 },
+ { 0x000080c0, 0x2a82301a },
+ { 0x000080c4, 0x05dc01e0 },
+ { 0x000080c8, 0x1f402710 },
+ { 0x000080cc, 0x01f40000 },
+ { 0x000080d0, 0x00001e00 },
+ { 0x000080d4, 0x00000000 },
+ { 0x000080d8, 0x00400000 },
+ { 0x000080e0, 0xffffffff },
+ { 0x000080e4, 0x0000ffff },
+ { 0x000080e8, 0x003f3f3f },
+ { 0x000080ec, 0x00000000 },
+ { 0x000080f0, 0x00000000 },
+ { 0x000080f4, 0x00000000 },
+ { 0x000080f8, 0x00000000 },
+ { 0x000080fc, 0x00020000 },
+ { 0x00008100, 0x00020000 },
+ { 0x00008104, 0x00000001 },
+ { 0x00008108, 0x00000052 },
+ { 0x0000810c, 0x00000000 },
+ { 0x00008110, 0x00000168 },
+ { 0x00008118, 0x000100aa },
+ { 0x0000811c, 0x00003210 },
+ { 0x00008120, 0x08f04800 },
+ { 0x00008124, 0x00000000 },
+ { 0x00008128, 0x00000000 },
+ { 0x0000812c, 0x00000000 },
+ { 0x00008130, 0x00000000 },
+ { 0x00008134, 0x00000000 },
+ { 0x00008138, 0x00000000 },
+ { 0x0000813c, 0x00000000 },
+ { 0x00008144, 0x00000000 },
+ { 0x00008168, 0x00000000 },
+ { 0x0000816c, 0x00000000 },
+ { 0x00008170, 0x32143320 },
+ { 0x00008174, 0xfaa4fa50 },
+ { 0x00008178, 0x00000100 },
+ { 0x0000817c, 0x00000000 },
+ { 0x000081c4, 0x00000000 },
+ { 0x000081d0, 0x00003210 },
+ { 0x000081ec, 0x00000000 },
+ { 0x000081f0, 0x00000000 },
+ { 0x000081f4, 0x00000000 },
+ { 0x000081f8, 0x00000000 },
+ { 0x000081fc, 0x00000000 },
+ { 0x00008200, 0x00000000 },
+ { 0x00008204, 0x00000000 },
+ { 0x00008208, 0x00000000 },
+ { 0x0000820c, 0x00000000 },
+ { 0x00008210, 0x00000000 },
+ { 0x00008214, 0x00000000 },
+ { 0x00008218, 0x00000000 },
+ { 0x0000821c, 0x00000000 },
+ { 0x00008220, 0x00000000 },
+ { 0x00008224, 0x00000000 },
+ { 0x00008228, 0x00000000 },
+ { 0x0000822c, 0x00000000 },
+ { 0x00008230, 0x00000000 },
+ { 0x00008234, 0x00000000 },
+ { 0x00008238, 0x00000000 },
+ { 0x0000823c, 0x00000000 },
+ { 0x00008240, 0x00100000 },
+ { 0x00008244, 0x0010f400 },
+ { 0x00008248, 0x00000100 },
+ { 0x0000824c, 0x0001e800 },
+ { 0x00008250, 0x00000000 },
+ { 0x00008254, 0x00000000 },
+ { 0x00008258, 0x00000000 },
+ { 0x0000825c, 0x400000ff },
+ { 0x00008260, 0x00080922 },
+ { 0x00008270, 0x00000000 },
+ { 0x00008274, 0x40000000 },
+ { 0x00008278, 0x003e4180 },
+ { 0x0000827c, 0x00000000 },
+ { 0x00008284, 0x0000002c },
+ { 0x00008288, 0x0000002c },
+ { 0x0000828c, 0x00000000 },
+ { 0x00008294, 0x00000000 },
+ { 0x00008298, 0x00000000 },
+ { 0x00008300, 0x00000000 },
+ { 0x00008304, 0x00000000 },
+ { 0x00008308, 0x00000000 },
+ { 0x0000830c, 0x00000000 },
+ { 0x00008310, 0x00000000 },
+ { 0x00008314, 0x00000000 },
+ { 0x00008318, 0x00000000 },
+ { 0x00008328, 0x00000000 },
+ { 0x0000832c, 0x00000007 },
+ { 0x00008330, 0x00000302 },
+ { 0x00008334, 0x00000e00 },
+ { 0x00008338, 0x00000000 },
+ { 0x0000833c, 0x00000000 },
+ { 0x00008340, 0x000107ff },
+ { 0x00009808, 0x00000000 },
+ { 0x0000980c, 0xad848e19 },
+ { 0x00009810, 0x7d14e000 },
+ { 0x00009814, 0x9c0a9f6b },
+ { 0x0000981c, 0x00000000 },
+ { 0x0000982c, 0x0000a000 },
+ { 0x00009830, 0x00000000 },
+ { 0x0000983c, 0x00200400 },
+ { 0x00009840, 0x206a002e },
+ { 0x0000984c, 0x1284233c },
+ { 0x00009854, 0x00000859 },
+ { 0x00009900, 0x00000000 },
+ { 0x00009904, 0x00000000 },
+ { 0x00009908, 0x00000000 },
+ { 0x0000990c, 0x00000000 },
+ { 0x0000991c, 0x10000fff },
+ { 0x00009920, 0x05100000 },
+ { 0x0000a920, 0x05100000 },
+ { 0x0000b920, 0x05100000 },
+ { 0x00009928, 0x00000001 },
+ { 0x0000992c, 0x00000004 },
+ { 0x00009934, 0x1e1f2022 },
+ { 0x00009938, 0x0a0b0c0d },
+ { 0x0000993c, 0x00000000 },
+ { 0x00009948, 0x9280b212 },
+ { 0x0000994c, 0x00020028 },
+ { 0x00009954, 0x5d50e188 },
+ { 0x00009958, 0x00081fff },
+ { 0x0000c95c, 0x004b6a8e },
+ { 0x0000c968, 0x000003ce },
+ { 0x00009970, 0x190fb515 },
+ { 0x00009974, 0x00000000 },
+ { 0x00009978, 0x00000001 },
+ { 0x0000997c, 0x00000000 },
+ { 0x00009980, 0x00000000 },
+ { 0x00009984, 0x00000000 },
+ { 0x00009988, 0x00000000 },
+ { 0x0000998c, 0x00000000 },
+ { 0x00009990, 0x00000000 },
+ { 0x00009994, 0x00000000 },
+ { 0x00009998, 0x00000000 },
+ { 0x0000999c, 0x00000000 },
+ { 0x000099a0, 0x00000000 },
+ { 0x000099a4, 0x00000001 },
+ { 0x000099a8, 0x001fff00 },
+ { 0x000099ac, 0x00000000 },
+ { 0x000099b0, 0x03051000 },
+ { 0x000099dc, 0x00000000 },
+ { 0x000099e0, 0x00000200 },
+ { 0x000099e4, 0xaaaaaaaa },
+ { 0x000099e8, 0x3c466478 },
+ { 0x000099ec, 0x000000aa },
+ { 0x000099fc, 0x00001042 },
+ { 0x00009b00, 0x00000000 },
+ { 0x00009b04, 0x00000001 },
+ { 0x00009b08, 0x00000002 },
+ { 0x00009b0c, 0x00000003 },
+ { 0x00009b10, 0x00000004 },
+ { 0x00009b14, 0x00000005 },
+ { 0x00009b18, 0x00000008 },
+ { 0x00009b1c, 0x00000009 },
+ { 0x00009b20, 0x0000000a },
+ { 0x00009b24, 0x0000000b },
+ { 0x00009b28, 0x0000000c },
+ { 0x00009b2c, 0x0000000d },
+ { 0x00009b30, 0x00000010 },
+ { 0x00009b34, 0x00000011 },
+ { 0x00009b38, 0x00000012 },
+ { 0x00009b3c, 0x00000013 },
+ { 0x00009b40, 0x00000014 },
+ { 0x00009b44, 0x00000015 },
+ { 0x00009b48, 0x00000018 },
+ { 0x00009b4c, 0x00000019 },
+ { 0x00009b50, 0x0000001a },
+ { 0x00009b54, 0x0000001b },
+ { 0x00009b58, 0x0000001c },
+ { 0x00009b5c, 0x0000001d },
+ { 0x00009b60, 0x00000020 },
+ { 0x00009b64, 0x00000021 },
+ { 0x00009b68, 0x00000022 },
+ { 0x00009b6c, 0x00000023 },
+ { 0x00009b70, 0x00000024 },
+ { 0x00009b74, 0x00000025 },
+ { 0x00009b78, 0x00000028 },
+ { 0x00009b7c, 0x00000029 },
+ { 0x00009b80, 0x0000002a },
+ { 0x00009b84, 0x0000002b },
+ { 0x00009b88, 0x0000002c },
+ { 0x00009b8c, 0x0000002d },
+ { 0x00009b90, 0x00000030 },
+ { 0x00009b94, 0x00000031 },
+ { 0x00009b98, 0x00000032 },
+ { 0x00009b9c, 0x00000033 },
+ { 0x00009ba0, 0x00000034 },
+ { 0x00009ba4, 0x00000035 },
+ { 0x00009ba8, 0x00000035 },
+ { 0x00009bac, 0x00000035 },
+ { 0x00009bb0, 0x00000035 },
+ { 0x00009bb4, 0x00000035 },
+ { 0x00009bb8, 0x00000035 },
+ { 0x00009bbc, 0x00000035 },
+ { 0x00009bc0, 0x00000035 },
+ { 0x00009bc4, 0x00000035 },
+ { 0x00009bc8, 0x00000035 },
+ { 0x00009bcc, 0x00000035 },
+ { 0x00009bd0, 0x00000035 },
+ { 0x00009bd4, 0x00000035 },
+ { 0x00009bd8, 0x00000035 },
+ { 0x00009bdc, 0x00000035 },
+ { 0x00009be0, 0x00000035 },
+ { 0x00009be4, 0x00000035 },
+ { 0x00009be8, 0x00000035 },
+ { 0x00009bec, 0x00000035 },
+ { 0x00009bf0, 0x00000035 },
+ { 0x00009bf4, 0x00000035 },
+ { 0x00009bf8, 0x00000010 },
+ { 0x00009bfc, 0x0000001a },
+ { 0x0000a210, 0x40806333 },
+ { 0x0000a214, 0x00106c10 },
+ { 0x0000a218, 0x009c4060 },
+ { 0x0000a220, 0x018830c6 },
+ { 0x0000a224, 0x00000400 },
+ { 0x0000a228, 0x00000bb5 },
+ { 0x0000a22c, 0x00000011 },
+ { 0x0000a234, 0x20202020 },
+ { 0x0000a238, 0x20202020 },
+ { 0x0000a23c, 0x13c889af },
+ { 0x0000a240, 0x38490a20 },
+ { 0x0000a244, 0x00007bb6 },
+ { 0x0000a248, 0x0fff3ffc },
+ { 0x0000a24c, 0x00000001 },
+ { 0x0000a250, 0x0000a000 },
+ { 0x0000a254, 0x00000000 },
+ { 0x0000a258, 0x0cc75380 },
+ { 0x0000a25c, 0x0f0f0f01 },
+ { 0x0000a260, 0xdfa91f01 },
+ { 0x0000a268, 0x00000000 },
+ { 0x0000a26c, 0x0ebae9c6 },
+ { 0x0000b26c, 0x0ebae9c6 },
+ { 0x0000c26c, 0x0ebae9c6 },
+ { 0x0000d270, 0x00820820 },
+ { 0x0000a278, 0x1ce739ce },
+ { 0x0000a27c, 0x051701ce },
+ { 0x0000a338, 0x00000000 },
+ { 0x0000a33c, 0x00000000 },
+ { 0x0000a340, 0x00000000 },
+ { 0x0000a344, 0x00000000 },
+ { 0x0000a348, 0x3fffffff },
+ { 0x0000a34c, 0x3fffffff },
+ { 0x0000a350, 0x3fffffff },
+ { 0x0000a354, 0x0003ffff },
+ { 0x0000a358, 0x79a8aa1f },
+ { 0x0000d35c, 0x07ffffef },
+ { 0x0000d360, 0x0fffffe7 },
+ { 0x0000d364, 0x17ffffe5 },
+ { 0x0000d368, 0x1fffffe4 },
+ { 0x0000d36c, 0x37ffffe3 },
+ { 0x0000d370, 0x3fffffe3 },
+ { 0x0000d374, 0x57ffffe3 },
+ { 0x0000d378, 0x5fffffe2 },
+ { 0x0000d37c, 0x7fffffe2 },
+ { 0x0000d380, 0x7f3c7bba },
+ { 0x0000d384, 0xf3307ff0 },
+ { 0x0000a388, 0x08000000 },
+ { 0x0000a38c, 0x20202020 },
+ { 0x0000a390, 0x20202020 },
+ { 0x0000a394, 0x1ce739ce },
+ { 0x0000a398, 0x000001ce },
+ { 0x0000a39c, 0x00000001 },
+ { 0x0000a3a0, 0x00000000 },
+ { 0x0000a3a4, 0x00000000 },
+ { 0x0000a3a8, 0x00000000 },
+ { 0x0000a3ac, 0x00000000 },
+ { 0x0000a3b0, 0x00000000 },
+ { 0x0000a3b4, 0x00000000 },
+ { 0x0000a3b8, 0x00000000 },
+ { 0x0000a3bc, 0x00000000 },
+ { 0x0000a3c0, 0x00000000 },
+ { 0x0000a3c4, 0x00000000 },
+ { 0x0000a3c8, 0x00000246 },
+ { 0x0000a3cc, 0x20202020 },
+ { 0x0000a3d0, 0x20202020 },
+ { 0x0000a3d4, 0x20202020 },
+ { 0x0000a3dc, 0x1ce739ce },
+ { 0x0000a3e0, 0x000001ce },
+};
+
+static const u32 ar5416Bank0_9100[][2] = {
+ { 0x000098b0, 0x1e5795e5 },
+ { 0x000098e0, 0x02008020 },
+};
+
+static const u32 ar5416BB_RfGain_9100[][3] = {
+ { 0x00009a00, 0x00000000, 0x00000000 },
+ { 0x00009a04, 0x00000040, 0x00000040 },
+ { 0x00009a08, 0x00000080, 0x00000080 },
+ { 0x00009a0c, 0x000001a1, 0x00000141 },
+ { 0x00009a10, 0x000001e1, 0x00000181 },
+ { 0x00009a14, 0x00000021, 0x000001c1 },
+ { 0x00009a18, 0x00000061, 0x00000001 },
+ { 0x00009a1c, 0x00000168, 0x00000041 },
+ { 0x00009a20, 0x000001a8, 0x000001a8 },
+ { 0x00009a24, 0x000001e8, 0x000001e8 },
+ { 0x00009a28, 0x00000028, 0x00000028 },
+ { 0x00009a2c, 0x00000068, 0x00000068 },
+ { 0x00009a30, 0x00000189, 0x000000a8 },
+ { 0x00009a34, 0x000001c9, 0x00000169 },
+ { 0x00009a38, 0x00000009, 0x000001a9 },
+ { 0x00009a3c, 0x00000049, 0x000001e9 },
+ { 0x00009a40, 0x00000089, 0x00000029 },
+ { 0x00009a44, 0x00000170, 0x00000069 },
+ { 0x00009a48, 0x000001b0, 0x00000190 },
+ { 0x00009a4c, 0x000001f0, 0x000001d0 },
+ { 0x00009a50, 0x00000030, 0x00000010 },
+ { 0x00009a54, 0x00000070, 0x00000050 },
+ { 0x00009a58, 0x00000191, 0x00000090 },
+ { 0x00009a5c, 0x000001d1, 0x00000151 },
+ { 0x00009a60, 0x00000011, 0x00000191 },
+ { 0x00009a64, 0x00000051, 0x000001d1 },
+ { 0x00009a68, 0x00000091, 0x00000011 },
+ { 0x00009a6c, 0x000001b8, 0x00000051 },
+ { 0x00009a70, 0x000001f8, 0x00000198 },
+ { 0x00009a74, 0x00000038, 0x000001d8 },
+ { 0x00009a78, 0x00000078, 0x00000018 },
+ { 0x00009a7c, 0x00000199, 0x00000058 },
+ { 0x00009a80, 0x000001d9, 0x00000098 },
+ { 0x00009a84, 0x00000019, 0x00000159 },
+ { 0x00009a88, 0x00000059, 0x00000199 },
+ { 0x00009a8c, 0x00000099, 0x000001d9 },
+ { 0x00009a90, 0x000000d9, 0x00000019 },
+ { 0x00009a94, 0x000000f9, 0x00000059 },
+ { 0x00009a98, 0x000000f9, 0x00000099 },
+ { 0x00009a9c, 0x000000f9, 0x000000d9 },
+ { 0x00009aa0, 0x000000f9, 0x000000f9 },
+ { 0x00009aa4, 0x000000f9, 0x000000f9 },
+ { 0x00009aa8, 0x000000f9, 0x000000f9 },
+ { 0x00009aac, 0x000000f9, 0x000000f9 },
+ { 0x00009ab0, 0x000000f9, 0x000000f9 },
+ { 0x00009ab4, 0x000000f9, 0x000000f9 },
+ { 0x00009ab8, 0x000000f9, 0x000000f9 },
+ { 0x00009abc, 0x000000f9, 0x000000f9 },
+ { 0x00009ac0, 0x000000f9, 0x000000f9 },
+ { 0x00009ac4, 0x000000f9, 0x000000f9 },
+ { 0x00009ac8, 0x000000f9, 0x000000f9 },
+ { 0x00009acc, 0x000000f9, 0x000000f9 },
+ { 0x00009ad0, 0x000000f9, 0x000000f9 },
+ { 0x00009ad4, 0x000000f9, 0x000000f9 },
+ { 0x00009ad8, 0x000000f9, 0x000000f9 },
+ { 0x00009adc, 0x000000f9, 0x000000f9 },
+ { 0x00009ae0, 0x000000f9, 0x000000f9 },
+ { 0x00009ae4, 0x000000f9, 0x000000f9 },
+ { 0x00009ae8, 0x000000f9, 0x000000f9 },
+ { 0x00009aec, 0x000000f9, 0x000000f9 },
+ { 0x00009af0, 0x000000f9, 0x000000f9 },
+ { 0x00009af4, 0x000000f9, 0x000000f9 },
+ { 0x00009af8, 0x000000f9, 0x000000f9 },
+ { 0x00009afc, 0x000000f9, 0x000000f9 },
+};
+
+static const u32 ar5416Bank1_9100[][2] = {
+ { 0x000098b0, 0x02108421 },
+ { 0x000098ec, 0x00000008 },
+};
+
+static const u32 ar5416Bank2_9100[][2] = {
+ { 0x000098b0, 0x0e73ff17 },
+ { 0x000098e0, 0x00000420 },
+};
+
+static const u32 ar5416Bank3_9100[][3] = {
+ { 0x000098f0, 0x01400018, 0x01c00018 },
+};
+
+static const u32 ar5416Bank6_9100[][3] = {
+
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x40ff0000, 0x40ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x004210a2, 0x004210a2 },
+ { 0x0000989c, 0x0014008f, 0x0014008f },
+ { 0x0000989c, 0x00c40003, 0x00c40003 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x0001805e, 0x0001805e },
+ { 0x0000989c, 0x0000c0ab, 0x0000c0ab },
+ { 0x0000989c, 0x000000f1, 0x000000f1 },
+ { 0x0000989c, 0x00002081, 0x00002081 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+static const u32 ar5416Bank6TPC_9100[][3] = {
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x40ff0000, 0x40ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x00423022, 0x00423022 },
+ { 0x0000989c, 0x201400df, 0x201400df },
+ { 0x0000989c, 0x00c40002, 0x00c40002 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x0001805e, 0x0001805e },
+ { 0x0000989c, 0x0000c0ab, 0x0000c0ab },
+ { 0x0000989c, 0x000000e1, 0x000000e1 },
+ { 0x0000989c, 0x00007081, 0x00007081 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+static const u32 ar5416Bank7_9100[][2] = {
+ { 0x0000989c, 0x00000500 },
+ { 0x0000989c, 0x00000800 },
+ { 0x000098cc, 0x0000000e },
+};
+
+static const u32 ar5416Addac_9100[][2] = {
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000003 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x0000000c },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000030 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000060 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000058 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x000098c4, 0x00000000 },
+};
+
+static const u32 ar5416Modes[][6] = {
+ { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 },
+ { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 },
+ { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 },
+ { 0x000010f0, 0x0000a000, 0x00014000, 0x00016000, 0x0000b000, 0x00014008 },
+ { 0x00008014, 0x03e803e8, 0x07d007d0, 0x10801600, 0x08400b00, 0x06e006e0 },
+ { 0x0000801c, 0x128d93a7, 0x128d93cf, 0x12e013d7, 0x12e013ab, 0x098813cf },
+ { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 },
+ { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 },
+ { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 },
+ { 0x00009844, 0x0372161e, 0x0372161e, 0x037216a0, 0x037216a0, 0x037216a0 },
+ { 0x00009848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000a848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000b848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x00009850, 0x6d48b4e2, 0x6d48b4e2, 0x6d48b0e2, 0x6d48b0e2, 0x6d48b0e2 },
+ { 0x00009858, 0x7ec82d2e, 0x7ec82d2e, 0x7ec86d2e, 0x7ec84d2e, 0x7ec82d2e },
+ { 0x0000985c, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e },
+ { 0x00009860, 0x00048d18, 0x00048d18, 0x00048d20, 0x00048d20, 0x00048d18 },
+ { 0x0000c864, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00 },
+ { 0x00009868, 0x409a40d0, 0x409a40d0, 0x409a40d0, 0x409a40d0, 0x409a40d0 },
+ { 0x0000986c, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081 },
+ { 0x00009914, 0x000007d0, 0x000007d0, 0x00000898, 0x00000898, 0x000007d0 },
+ { 0x00009918, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b, 0x00000016 },
+ { 0x00009924, 0xd00a8a07, 0xd00a8a07, 0xd00a8a11, 0xd00a8a0d, 0xd00a8a0d },
+ { 0x00009940, 0x00754604, 0x00754604, 0xfff81204, 0xfff81204, 0xfff81204 },
+ { 0x00009944, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020 },
+ { 0x00009954, 0x5f3ca3de, 0x5f3ca3de, 0xe250a51e, 0xe250a51e, 0xe250a51e },
+ { 0x00009958, 0x2108ecff, 0x2108ecff, 0x3388ffff, 0x3388ffff, 0x3388ffff },
+#ifdef TB243
+ { 0x00009960, 0x00000900, 0x00000900, 0x00009b40, 0x00009b40, 0x00012d80 },
+ { 0x0000a960, 0x00000900, 0x00000900, 0x00009b40, 0x00009b40, 0x00012d80 },
+ { 0x0000b960, 0x00000900, 0x00000900, 0x00009b40, 0x00009b40, 0x00012d80 },
+ { 0x00009964, 0x00000000, 0x00000000, 0x00002210, 0x00002210, 0x00001120 },
+#else
+ { 0x00009960, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0 },
+ { 0x0000a960, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0 },
+ { 0x0000b960, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0, 0x0001bfc0 },
+ { 0x00009964, 0x00001120, 0x00001120, 0x00001120, 0x00001120, 0x00001120 },
+#endif
+ { 0x0000c9bc, 0x001a0600, 0x001a0600, 0x001a1000, 0x001a0c00, 0x001a0c00 },
+ { 0x000099c0, 0x038919be, 0x038919be, 0x038919be, 0x038919be, 0x038919be },
+ { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 },
+ { 0x000099c8, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329 },
+ { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 },
+ { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 },
+ { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x000099d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a204, 0x00000880, 0x00000880, 0x00000880, 0x00000880, 0x00000880 },
+ { 0x0000a208, 0xd6be4788, 0xd6be4788, 0xd03e4788, 0xd03e4788, 0xd03e4788 },
+ { 0x0000a20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000b20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000c20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000a21c, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a },
+ { 0x0000a230, 0x00000000, 0x00000000, 0x00000210, 0x00000108, 0x00000000 },
+ { 0x0000a274, 0x0a1a9caa, 0x0a1a9caa, 0x0a1a7caa, 0x0a1a7caa, 0x0a1a7caa },
+ { 0x0000a300, 0x18010000, 0x18010000, 0x18010000, 0x18010000, 0x18010000 },
+ { 0x0000a304, 0x30032602, 0x30032602, 0x2e032402, 0x2e032402, 0x2e032402 },
+ { 0x0000a308, 0x48073e06, 0x48073e06, 0x4a0a3c06, 0x4a0a3c06, 0x4a0a3c06 },
+ { 0x0000a30c, 0x560b4c0a, 0x560b4c0a, 0x621a540b, 0x621a540b, 0x621a540b },
+ { 0x0000a310, 0x641a600f, 0x641a600f, 0x764f6c1b, 0x764f6c1b, 0x764f6c1b },
+ { 0x0000a314, 0x7a4f6e1b, 0x7a4f6e1b, 0x845b7a5a, 0x845b7a5a, 0x845b7a5a },
+ { 0x0000a318, 0x8c5b7e5a, 0x8c5b7e5a, 0x950f8ccf, 0x950f8ccf, 0x950f8ccf },
+ { 0x0000a31c, 0x9d0f96cf, 0x9d0f96cf, 0xa5cf9b4f, 0xa5cf9b4f, 0xa5cf9b4f },
+ { 0x0000a320, 0xb51fa69f, 0xb51fa69f, 0xbddfaf1f, 0xbddfaf1f, 0xbddfaf1f },
+ { 0x0000a324, 0xcb3fbd07, 0xcb3fbcbf, 0xd1ffc93f, 0xd1ffc93f, 0xd1ffc93f },
+ { 0x0000a328, 0x0000d7bf, 0x0000d7bf, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a32c, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a330, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a334, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+};
+
+static const u32 ar5416Common[][2] = {
+ { 0x0000000c, 0x00000000 },
+ { 0x00000030, 0x00020015 },
+ { 0x00000034, 0x00000005 },
+ { 0x00000040, 0x00000000 },
+ { 0x00000044, 0x00000008 },
+ { 0x00000048, 0x00000008 },
+ { 0x0000004c, 0x00000010 },
+ { 0x00000050, 0x00000000 },
+ { 0x00000054, 0x0000001f },
+ { 0x00000800, 0x00000000 },
+ { 0x00000804, 0x00000000 },
+ { 0x00000808, 0x00000000 },
+ { 0x0000080c, 0x00000000 },
+ { 0x00000810, 0x00000000 },
+ { 0x00000814, 0x00000000 },
+ { 0x00000818, 0x00000000 },
+ { 0x0000081c, 0x00000000 },
+ { 0x00000820, 0x00000000 },
+ { 0x00000824, 0x00000000 },
+ { 0x00001040, 0x002ffc0f },
+ { 0x00001044, 0x002ffc0f },
+ { 0x00001048, 0x002ffc0f },
+ { 0x0000104c, 0x002ffc0f },
+ { 0x00001050, 0x002ffc0f },
+ { 0x00001054, 0x002ffc0f },
+ { 0x00001058, 0x002ffc0f },
+ { 0x0000105c, 0x002ffc0f },
+ { 0x00001060, 0x002ffc0f },
+ { 0x00001064, 0x002ffc0f },
+ { 0x00001230, 0x00000000 },
+ { 0x00001270, 0x00000000 },
+ { 0x00001038, 0x00000000 },
+ { 0x00001078, 0x00000000 },
+ { 0x000010b8, 0x00000000 },
+ { 0x000010f8, 0x00000000 },
+ { 0x00001138, 0x00000000 },
+ { 0x00001178, 0x00000000 },
+ { 0x000011b8, 0x00000000 },
+ { 0x000011f8, 0x00000000 },
+ { 0x00001238, 0x00000000 },
+ { 0x00001278, 0x00000000 },
+ { 0x000012b8, 0x00000000 },
+ { 0x000012f8, 0x00000000 },
+ { 0x00001338, 0x00000000 },
+ { 0x00001378, 0x00000000 },
+ { 0x000013b8, 0x00000000 },
+ { 0x000013f8, 0x00000000 },
+ { 0x00001438, 0x00000000 },
+ { 0x00001478, 0x00000000 },
+ { 0x000014b8, 0x00000000 },
+ { 0x000014f8, 0x00000000 },
+ { 0x00001538, 0x00000000 },
+ { 0x00001578, 0x00000000 },
+ { 0x000015b8, 0x00000000 },
+ { 0x000015f8, 0x00000000 },
+ { 0x00001638, 0x00000000 },
+ { 0x00001678, 0x00000000 },
+ { 0x000016b8, 0x00000000 },
+ { 0x000016f8, 0x00000000 },
+ { 0x00001738, 0x00000000 },
+ { 0x00001778, 0x00000000 },
+ { 0x000017b8, 0x00000000 },
+ { 0x000017f8, 0x00000000 },
+ { 0x0000103c, 0x00000000 },
+ { 0x0000107c, 0x00000000 },
+ { 0x000010bc, 0x00000000 },
+ { 0x000010fc, 0x00000000 },
+ { 0x0000113c, 0x00000000 },
+ { 0x0000117c, 0x00000000 },
+ { 0x000011bc, 0x00000000 },
+ { 0x000011fc, 0x00000000 },
+ { 0x0000123c, 0x00000000 },
+ { 0x0000127c, 0x00000000 },
+ { 0x000012bc, 0x00000000 },
+ { 0x000012fc, 0x00000000 },
+ { 0x0000133c, 0x00000000 },
+ { 0x0000137c, 0x00000000 },
+ { 0x000013bc, 0x00000000 },
+ { 0x000013fc, 0x00000000 },
+ { 0x0000143c, 0x00000000 },
+ { 0x0000147c, 0x00000000 },
+ { 0x00020010, 0x00000003 },
+ { 0x00020038, 0x000004c2 },
+ { 0x00008004, 0x00000000 },
+ { 0x00008008, 0x00000000 },
+ { 0x0000800c, 0x00000000 },
+ { 0x00008018, 0x00000700 },
+ { 0x00008020, 0x00000000 },
+ { 0x00008038, 0x00000000 },
+ { 0x0000803c, 0x00000000 },
+ { 0x00008048, 0x40000000 },
+ { 0x00008054, 0x00004000 },
+ { 0x00008058, 0x00000000 },
+ { 0x0000805c, 0x000fc78f },
+ { 0x00008060, 0x0000000f },
+ { 0x00008064, 0x00000000 },
+ { 0x000080c0, 0x2a82301a },
+ { 0x000080c4, 0x05dc01e0 },
+ { 0x000080c8, 0x1f402710 },
+ { 0x000080cc, 0x01f40000 },
+ { 0x000080d0, 0x00001e00 },
+ { 0x000080d4, 0x00000000 },
+ { 0x000080d8, 0x00400000 },
+ { 0x000080e0, 0xffffffff },
+ { 0x000080e4, 0x0000ffff },
+ { 0x000080e8, 0x003f3f3f },
+ { 0x000080ec, 0x00000000 },
+ { 0x000080f0, 0x00000000 },
+ { 0x000080f4, 0x00000000 },
+ { 0x000080f8, 0x00000000 },
+ { 0x000080fc, 0x00020000 },
+ { 0x00008100, 0x00020000 },
+ { 0x00008104, 0x00000001 },
+ { 0x00008108, 0x00000052 },
+ { 0x0000810c, 0x00000000 },
+ { 0x00008110, 0x00000168 },
+ { 0x00008118, 0x000100aa },
+ { 0x0000811c, 0x00003210 },
+ { 0x00008120, 0x08f04800 },
+ { 0x00008124, 0x00000000 },
+ { 0x00008128, 0x00000000 },
+ { 0x0000812c, 0x00000000 },
+ { 0x00008130, 0x00000000 },
+ { 0x00008134, 0x00000000 },
+ { 0x00008138, 0x00000000 },
+ { 0x0000813c, 0x00000000 },
+ { 0x00008144, 0x00000000 },
+ { 0x00008168, 0x00000000 },
+ { 0x0000816c, 0x00000000 },
+ { 0x00008170, 0x32143320 },
+ { 0x00008174, 0xfaa4fa50 },
+ { 0x00008178, 0x00000100 },
+ { 0x0000817c, 0x00000000 },
+ { 0x000081c4, 0x00000000 },
+ { 0x000081d0, 0x00003210 },
+ { 0x000081ec, 0x00000000 },
+ { 0x000081f0, 0x00000000 },
+ { 0x000081f4, 0x00000000 },
+ { 0x000081f8, 0x00000000 },
+ { 0x000081fc, 0x00000000 },
+ { 0x00008200, 0x00000000 },
+ { 0x00008204, 0x00000000 },
+ { 0x00008208, 0x00000000 },
+ { 0x0000820c, 0x00000000 },
+ { 0x00008210, 0x00000000 },
+ { 0x00008214, 0x00000000 },
+ { 0x00008218, 0x00000000 },
+ { 0x0000821c, 0x00000000 },
+ { 0x00008220, 0x00000000 },
+ { 0x00008224, 0x00000000 },
+ { 0x00008228, 0x00000000 },
+ { 0x0000822c, 0x00000000 },
+ { 0x00008230, 0x00000000 },
+ { 0x00008234, 0x00000000 },
+ { 0x00008238, 0x00000000 },
+ { 0x0000823c, 0x00000000 },
+ { 0x00008240, 0x00100000 },
+ { 0x00008244, 0x0010f400 },
+ { 0x00008248, 0x00000100 },
+ { 0x0000824c, 0x0001e800 },
+ { 0x00008250, 0x00000000 },
+ { 0x00008254, 0x00000000 },
+ { 0x00008258, 0x00000000 },
+ { 0x0000825c, 0x400000ff },
+ { 0x00008260, 0x00080922 },
+ { 0x00008270, 0x00000000 },
+ { 0x00008274, 0x40000000 },
+ { 0x00008278, 0x003e4180 },
+ { 0x0000827c, 0x00000000 },
+ { 0x00008284, 0x0000002c },
+ { 0x00008288, 0x0000002c },
+ { 0x0000828c, 0x00000000 },
+ { 0x00008294, 0x00000000 },
+ { 0x00008298, 0x00000000 },
+ { 0x00008300, 0x00000000 },
+ { 0x00008304, 0x00000000 },
+ { 0x00008308, 0x00000000 },
+ { 0x0000830c, 0x00000000 },
+ { 0x00008310, 0x00000000 },
+ { 0x00008314, 0x00000000 },
+ { 0x00008318, 0x00000000 },
+ { 0x00008328, 0x00000000 },
+ { 0x0000832c, 0x00000007 },
+ { 0x00008330, 0x00000302 },
+ { 0x00008334, 0x00000e00 },
+ { 0x00008338, 0x00000000 },
+ { 0x0000833c, 0x00000000 },
+ { 0x00008340, 0x000107ff },
+ { 0x00009808, 0x00000000 },
+ { 0x0000980c, 0xad848e19 },
+ { 0x00009810, 0x7d14e000 },
+ { 0x00009814, 0x9c0a9f6b },
+ { 0x0000981c, 0x00000000 },
+ { 0x0000982c, 0x0000a000 },
+ { 0x00009830, 0x00000000 },
+ { 0x0000983c, 0x00200400 },
+ { 0x00009840, 0x206a01ae },
+ { 0x0000984c, 0x1284233c },
+ { 0x00009854, 0x00000859 },
+ { 0x00009900, 0x00000000 },
+ { 0x00009904, 0x00000000 },
+ { 0x00009908, 0x00000000 },
+ { 0x0000990c, 0x00000000 },
+ { 0x0000991c, 0x10000fff },
+ { 0x00009920, 0x05100000 },
+ { 0x0000a920, 0x05100000 },
+ { 0x0000b920, 0x05100000 },
+ { 0x00009928, 0x00000001 },
+ { 0x0000992c, 0x00000004 },
+ { 0x00009934, 0x1e1f2022 },
+ { 0x00009938, 0x0a0b0c0d },
+ { 0x0000993c, 0x00000000 },
+ { 0x00009948, 0x9280b212 },
+ { 0x0000994c, 0x00020028 },
+ { 0x0000c95c, 0x004b6a8e },
+ { 0x0000c968, 0x000003ce },
+ { 0x00009970, 0x190fb514 },
+ { 0x00009974, 0x00000000 },
+ { 0x00009978, 0x00000001 },
+ { 0x0000997c, 0x00000000 },
+ { 0x00009980, 0x00000000 },
+ { 0x00009984, 0x00000000 },
+ { 0x00009988, 0x00000000 },
+ { 0x0000998c, 0x00000000 },
+ { 0x00009990, 0x00000000 },
+ { 0x00009994, 0x00000000 },
+ { 0x00009998, 0x00000000 },
+ { 0x0000999c, 0x00000000 },
+ { 0x000099a0, 0x00000000 },
+ { 0x000099a4, 0x00000001 },
+ { 0x000099a8, 0x201fff00 },
+ { 0x000099ac, 0x006f0000 },
+ { 0x000099b0, 0x03051000 },
+ { 0x000099dc, 0x00000000 },
+ { 0x000099e0, 0x00000200 },
+ { 0x000099e4, 0xaaaaaaaa },
+ { 0x000099e8, 0x3c466478 },
+ { 0x000099ec, 0x0cc80caa },
+ { 0x000099fc, 0x00001042 },
+ { 0x00009b00, 0x00000000 },
+ { 0x00009b04, 0x00000001 },
+ { 0x00009b08, 0x00000002 },
+ { 0x00009b0c, 0x00000003 },
+ { 0x00009b10, 0x00000004 },
+ { 0x00009b14, 0x00000005 },
+ { 0x00009b18, 0x00000008 },
+ { 0x00009b1c, 0x00000009 },
+ { 0x00009b20, 0x0000000a },
+ { 0x00009b24, 0x0000000b },
+ { 0x00009b28, 0x0000000c },
+ { 0x00009b2c, 0x0000000d },
+ { 0x00009b30, 0x00000010 },
+ { 0x00009b34, 0x00000011 },
+ { 0x00009b38, 0x00000012 },
+ { 0x00009b3c, 0x00000013 },
+ { 0x00009b40, 0x00000014 },
+ { 0x00009b44, 0x00000015 },
+ { 0x00009b48, 0x00000018 },
+ { 0x00009b4c, 0x00000019 },
+ { 0x00009b50, 0x0000001a },
+ { 0x00009b54, 0x0000001b },
+ { 0x00009b58, 0x0000001c },
+ { 0x00009b5c, 0x0000001d },
+ { 0x00009b60, 0x00000020 },
+ { 0x00009b64, 0x00000021 },
+ { 0x00009b68, 0x00000022 },
+ { 0x00009b6c, 0x00000023 },
+ { 0x00009b70, 0x00000024 },
+ { 0x00009b74, 0x00000025 },
+ { 0x00009b78, 0x00000028 },
+ { 0x00009b7c, 0x00000029 },
+ { 0x00009b80, 0x0000002a },
+ { 0x00009b84, 0x0000002b },
+ { 0x00009b88, 0x0000002c },
+ { 0x00009b8c, 0x0000002d },
+ { 0x00009b90, 0x00000030 },
+ { 0x00009b94, 0x00000031 },
+ { 0x00009b98, 0x00000032 },
+ { 0x00009b9c, 0x00000033 },
+ { 0x00009ba0, 0x00000034 },
+ { 0x00009ba4, 0x00000035 },
+ { 0x00009ba8, 0x00000035 },
+ { 0x00009bac, 0x00000035 },
+ { 0x00009bb0, 0x00000035 },
+ { 0x00009bb4, 0x00000035 },
+ { 0x00009bb8, 0x00000035 },
+ { 0x00009bbc, 0x00000035 },
+ { 0x00009bc0, 0x00000035 },
+ { 0x00009bc4, 0x00000035 },
+ { 0x00009bc8, 0x00000035 },
+ { 0x00009bcc, 0x00000035 },
+ { 0x00009bd0, 0x00000035 },
+ { 0x00009bd4, 0x00000035 },
+ { 0x00009bd8, 0x00000035 },
+ { 0x00009bdc, 0x00000035 },
+ { 0x00009be0, 0x00000035 },
+ { 0x00009be4, 0x00000035 },
+ { 0x00009be8, 0x00000035 },
+ { 0x00009bec, 0x00000035 },
+ { 0x00009bf0, 0x00000035 },
+ { 0x00009bf4, 0x00000035 },
+ { 0x00009bf8, 0x00000010 },
+ { 0x00009bfc, 0x0000001a },
+ { 0x0000a210, 0x40806333 },
+ { 0x0000a214, 0x00106c10 },
+ { 0x0000a218, 0x009c4060 },
+ { 0x0000a220, 0x018830c6 },
+ { 0x0000a224, 0x00000400 },
+ { 0x0000a228, 0x001a0bb5 },
+ { 0x0000a22c, 0x00000000 },
+ { 0x0000a234, 0x20202020 },
+ { 0x0000a238, 0x20202020 },
+ { 0x0000a23c, 0x13c889ae },
+ { 0x0000a240, 0x38490a20 },
+ { 0x0000a244, 0x00007bb6 },
+ { 0x0000a248, 0x0fff3ffc },
+ { 0x0000a24c, 0x00000001 },
+ { 0x0000a250, 0x0000a000 },
+ { 0x0000a254, 0x00000000 },
+ { 0x0000a258, 0x0cc75380 },
+ { 0x0000a25c, 0x0f0f0f01 },
+ { 0x0000a260, 0xdfa91f01 },
+ { 0x0000a268, 0x00000001 },
+ { 0x0000a26c, 0x0ebae9c6 },
+ { 0x0000b26c, 0x0ebae9c6 },
+ { 0x0000c26c, 0x0ebae9c6 },
+ { 0x0000d270, 0x00820820 },
+ { 0x0000a278, 0x1ce739ce },
+ { 0x0000a27c, 0x050701ce },
+ { 0x0000a338, 0x00000000 },
+ { 0x0000a33c, 0x00000000 },
+ { 0x0000a340, 0x00000000 },
+ { 0x0000a344, 0x00000000 },
+ { 0x0000a348, 0x3fffffff },
+ { 0x0000a34c, 0x3fffffff },
+ { 0x0000a350, 0x3fffffff },
+ { 0x0000a354, 0x0003ffff },
+ { 0x0000a358, 0x79a8aa33 },
+ { 0x0000d35c, 0x07ffffef },
+ { 0x0000d360, 0x0fffffe7 },
+ { 0x0000d364, 0x17ffffe5 },
+ { 0x0000d368, 0x1fffffe4 },
+ { 0x0000d36c, 0x37ffffe3 },
+ { 0x0000d370, 0x3fffffe3 },
+ { 0x0000d374, 0x57ffffe3 },
+ { 0x0000d378, 0x5fffffe2 },
+ { 0x0000d37c, 0x7fffffe2 },
+ { 0x0000d380, 0x7f3c7bba },
+ { 0x0000d384, 0xf3307ff0 },
+ { 0x0000a388, 0x0c000000 },
+ { 0x0000a38c, 0x20202020 },
+ { 0x0000a390, 0x20202020 },
+ { 0x0000a394, 0x1ce739ce },
+ { 0x0000a398, 0x000001ce },
+ { 0x0000a39c, 0x00000001 },
+ { 0x0000a3a0, 0x00000000 },
+ { 0x0000a3a4, 0x00000000 },
+ { 0x0000a3a8, 0x00000000 },
+ { 0x0000a3ac, 0x00000000 },
+ { 0x0000a3b0, 0x00000000 },
+ { 0x0000a3b4, 0x00000000 },
+ { 0x0000a3b8, 0x00000000 },
+ { 0x0000a3bc, 0x00000000 },
+ { 0x0000a3c0, 0x00000000 },
+ { 0x0000a3c4, 0x00000000 },
+ { 0x0000a3c8, 0x00000246 },
+ { 0x0000a3cc, 0x20202020 },
+ { 0x0000a3d0, 0x20202020 },
+ { 0x0000a3d4, 0x20202020 },
+ { 0x0000a3dc, 0x1ce739ce },
+ { 0x0000a3e0, 0x000001ce },
+};
+
+static const u32 ar5416Bank0[][2] = {
+ { 0x000098b0, 0x1e5795e5 },
+ { 0x000098e0, 0x02008020 },
+};
+
+static const u32 ar5416BB_RfGain[][3] = {
+ { 0x00009a00, 0x00000000, 0x00000000 },
+ { 0x00009a04, 0x00000040, 0x00000040 },
+ { 0x00009a08, 0x00000080, 0x00000080 },
+ { 0x00009a0c, 0x000001a1, 0x00000141 },
+ { 0x00009a10, 0x000001e1, 0x00000181 },
+ { 0x00009a14, 0x00000021, 0x000001c1 },
+ { 0x00009a18, 0x00000061, 0x00000001 },
+ { 0x00009a1c, 0x00000168, 0x00000041 },
+ { 0x00009a20, 0x000001a8, 0x000001a8 },
+ { 0x00009a24, 0x000001e8, 0x000001e8 },
+ { 0x00009a28, 0x00000028, 0x00000028 },
+ { 0x00009a2c, 0x00000068, 0x00000068 },
+ { 0x00009a30, 0x00000189, 0x000000a8 },
+ { 0x00009a34, 0x000001c9, 0x00000169 },
+ { 0x00009a38, 0x00000009, 0x000001a9 },
+ { 0x00009a3c, 0x00000049, 0x000001e9 },
+ { 0x00009a40, 0x00000089, 0x00000029 },
+ { 0x00009a44, 0x00000170, 0x00000069 },
+ { 0x00009a48, 0x000001b0, 0x00000190 },
+ { 0x00009a4c, 0x000001f0, 0x000001d0 },
+ { 0x00009a50, 0x00000030, 0x00000010 },
+ { 0x00009a54, 0x00000070, 0x00000050 },
+ { 0x00009a58, 0x00000191, 0x00000090 },
+ { 0x00009a5c, 0x000001d1, 0x00000151 },
+ { 0x00009a60, 0x00000011, 0x00000191 },
+ { 0x00009a64, 0x00000051, 0x000001d1 },
+ { 0x00009a68, 0x00000091, 0x00000011 },
+ { 0x00009a6c, 0x000001b8, 0x00000051 },
+ { 0x00009a70, 0x000001f8, 0x00000198 },
+ { 0x00009a74, 0x00000038, 0x000001d8 },
+ { 0x00009a78, 0x00000078, 0x00000018 },
+ { 0x00009a7c, 0x00000199, 0x00000058 },
+ { 0x00009a80, 0x000001d9, 0x00000098 },
+ { 0x00009a84, 0x00000019, 0x00000159 },
+ { 0x00009a88, 0x00000059, 0x00000199 },
+ { 0x00009a8c, 0x00000099, 0x000001d9 },
+ { 0x00009a90, 0x000000d9, 0x00000019 },
+ { 0x00009a94, 0x000000f9, 0x00000059 },
+ { 0x00009a98, 0x000000f9, 0x00000099 },
+ { 0x00009a9c, 0x000000f9, 0x000000d9 },
+ { 0x00009aa0, 0x000000f9, 0x000000f9 },
+ { 0x00009aa4, 0x000000f9, 0x000000f9 },
+ { 0x00009aa8, 0x000000f9, 0x000000f9 },
+ { 0x00009aac, 0x000000f9, 0x000000f9 },
+ { 0x00009ab0, 0x000000f9, 0x000000f9 },
+ { 0x00009ab4, 0x000000f9, 0x000000f9 },
+ { 0x00009ab8, 0x000000f9, 0x000000f9 },
+ { 0x00009abc, 0x000000f9, 0x000000f9 },
+ { 0x00009ac0, 0x000000f9, 0x000000f9 },
+ { 0x00009ac4, 0x000000f9, 0x000000f9 },
+ { 0x00009ac8, 0x000000f9, 0x000000f9 },
+ { 0x00009acc, 0x000000f9, 0x000000f9 },
+ { 0x00009ad0, 0x000000f9, 0x000000f9 },
+ { 0x00009ad4, 0x000000f9, 0x000000f9 },
+ { 0x00009ad8, 0x000000f9, 0x000000f9 },
+ { 0x00009adc, 0x000000f9, 0x000000f9 },
+ { 0x00009ae0, 0x000000f9, 0x000000f9 },
+ { 0x00009ae4, 0x000000f9, 0x000000f9 },
+ { 0x00009ae8, 0x000000f9, 0x000000f9 },
+ { 0x00009aec, 0x000000f9, 0x000000f9 },
+ { 0x00009af0, 0x000000f9, 0x000000f9 },
+ { 0x00009af4, 0x000000f9, 0x000000f9 },
+ { 0x00009af8, 0x000000f9, 0x000000f9 },
+ { 0x00009afc, 0x000000f9, 0x000000f9 },
+};
+
+static const u32 ar5416Bank1[][2] = {
+ { 0x000098b0, 0x02108421},
+ { 0x000098ec, 0x00000008},
+};
+
+static const u32 ar5416Bank2[][2] = {
+ { 0x000098b0, 0x0e73ff17},
+ { 0x000098e0, 0x00000420},
+};
+
+static const u32 ar5416Bank3[][3] = {
+ { 0x000098f0, 0x01400018, 0x01c00018 },
+};
+
+static const u32 ar5416Bank6[][3] = {
+
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x004210a2, 0x004210a2 },
+ { 0x0000989c, 0x0014000f, 0x0014000f },
+ { 0x0000989c, 0x00c40002, 0x00c40002 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x000180d6, 0x000180d6 },
+ { 0x0000989c, 0x0000c0aa, 0x0000c0aa },
+ { 0x0000989c, 0x000000b1, 0x000000b1 },
+ { 0x0000989c, 0x00002000, 0x00002000 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+
+static const u32 ar5416Bank6TPC[][3] = {
+
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x40ff0000, 0x40ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x00423022, 0x00423022 },
+ { 0x0000989c, 0x2014008f, 0x2014008f },
+ { 0x0000989c, 0x00c40002, 0x00c40002 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x0001805e, 0x0001805e },
+ { 0x0000989c, 0x0000c0ab, 0x0000c0ab },
+ { 0x0000989c, 0x000000e1, 0x000000e1 },
+ { 0x0000989c, 0x00007080, 0x00007080 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+static const u32 ar5416Bank7[][2] = {
+ { 0x0000989c, 0x00000500 },
+ { 0x0000989c, 0x00000800 },
+ { 0x000098cc, 0x0000000e },
+};
+
+static const u32 ar5416Addac[][2] = {
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000010 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x000000c0 },
+ {0x0000989c, 0x00000015 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x000098cc, 0x00000000 },
+};
+
+
+static const u32 ar5416Modes_9160[][6] = {
+ { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 },
+ { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 },
+ { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 },
+ { 0x000010f0, 0x0000a000, 0x00014000, 0x00016000, 0x0000b000, 0x00014008 },
+ { 0x00008014, 0x03e803e8, 0x07d007d0, 0x10801600, 0x08400b00, 0x06e006e0 },
+ { 0x0000801c, 0x128d93a7, 0x128d93cf, 0x12e013d7, 0x12e013ab, 0x098813cf },
+ { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 },
+ { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 },
+ { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 },
+ { 0x00009844, 0x0372161e, 0x0372161e, 0x037216a0, 0x037216a0, 0x037216a0 },
+ { 0x00009848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000a848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x0000b848, 0x001a6a65, 0x001a6a65, 0x00197a68, 0x00197a68, 0x00197a68 },
+ { 0x00009850, 0x6d48b4e2, 0x6d48b4e2, 0x6d48b0e2, 0x6d48b0e2, 0x6d48b0e2 },
+ { 0x00009858, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e },
+ { 0x0000985c, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e },
+ { 0x00009860, 0x00048d18, 0x00048d18, 0x00048d20, 0x00048d20, 0x00048d18 },
+ { 0x0000c864, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00 },
+ { 0x00009868, 0x409a40d0, 0x409a40d0, 0x409a40d0, 0x409a40d0, 0x409a40d0 },
+ { 0x0000986c, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081, 0x050cb081 },
+ { 0x00009914, 0x000007d0, 0x000007d0, 0x00000898, 0x00000898, 0x000007d0 },
+ { 0x00009918, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b, 0x00000016 },
+ { 0x00009924, 0xd00a8a07, 0xd00a8a07, 0xd00a8a0d, 0xd00a8a0d, 0xd00a8a0d },
+ { 0x00009944, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020, 0xdfb81020 },
+ { 0x00009960, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40 },
+ { 0x0000a960, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40 },
+ { 0x0000b960, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40, 0x00009b40 },
+ { 0x00009964, 0x00001120, 0x00001120, 0x00001120, 0x00001120, 0x00001120 },
+ { 0x0000c9bc, 0x001a0600, 0x001a0600, 0x001a0c00, 0x001a0c00, 0x001a0c00 },
+ { 0x000099c0, 0x038919be, 0x038919be, 0x038919be, 0x038919be, 0x038919be },
+ { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 },
+ { 0x000099c8, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329 },
+ { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 },
+ { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 },
+ { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x000099d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a204, 0x00000880, 0x00000880, 0x00000880, 0x00000880, 0x00000880 },
+ { 0x0000a208, 0xd6be4788, 0xd6be4788, 0xd03e4788, 0xd03e4788, 0xd03e4788 },
+ { 0x0000a20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000b20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000c20c, 0x002fc160, 0x002fc160, 0x002ac120, 0x002ac120, 0x002ac120 },
+ { 0x0000a21c, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a },
+ { 0x0000a230, 0x00000000, 0x00000000, 0x00000210, 0x00000108, 0x00000000 },
+ { 0x0000a274, 0x0a1a9caa, 0x0a1a9caa, 0x0a1a7caa, 0x0a1a7caa, 0x0a1a7caa },
+ { 0x0000a300, 0x18010000, 0x18010000, 0x18010000, 0x18010000, 0x18010000 },
+ { 0x0000a304, 0x30032602, 0x30032602, 0x2e032402, 0x2e032402, 0x2e032402 },
+ { 0x0000a308, 0x48073e06, 0x48073e06, 0x4a0a3c06, 0x4a0a3c06, 0x4a0a3c06 },
+ { 0x0000a30c, 0x560b4c0a, 0x560b4c0a, 0x621a540b, 0x621a540b, 0x621a540b },
+ { 0x0000a310, 0x641a600f, 0x641a600f, 0x764f6c1b, 0x764f6c1b, 0x764f6c1b },
+ { 0x0000a314, 0x7a4f6e1b, 0x7a4f6e1b, 0x845b7a5a, 0x845b7a5a, 0x845b7a5a },
+ { 0x0000a318, 0x8c5b7e5a, 0x8c5b7e5a, 0x950f8ccf, 0x950f8ccf, 0x950f8ccf },
+ { 0x0000a31c, 0x9d0f96cf, 0x9d0f96cf, 0xa5cf9b4f, 0xa5cf9b4f, 0xa5cf9b4f },
+ { 0x0000a320, 0xb51fa69f, 0xb51fa69f, 0xbddfaf1f, 0xbddfaf1f, 0xbddfaf1f },
+ { 0x0000a324, 0xcb3fbd07, 0xcb3fbcbf, 0xd1ffc93f, 0xd1ffc93f, 0xd1ffc93f },
+ { 0x0000a328, 0x0000d7bf, 0x0000d7bf, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a32c, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a330, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a334, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+};
+
+static const u32 ar5416Common_9160[][2] = {
+ { 0x0000000c, 0x00000000 },
+ { 0x00000030, 0x00020015 },
+ { 0x00000034, 0x00000005 },
+ { 0x00000040, 0x00000000 },
+ { 0x00000044, 0x00000008 },
+ { 0x00000048, 0x00000008 },
+ { 0x0000004c, 0x00000010 },
+ { 0x00000050, 0x00000000 },
+ { 0x00000054, 0x0000001f },
+ { 0x00000800, 0x00000000 },
+ { 0x00000804, 0x00000000 },
+ { 0x00000808, 0x00000000 },
+ { 0x0000080c, 0x00000000 },
+ { 0x00000810, 0x00000000 },
+ { 0x00000814, 0x00000000 },
+ { 0x00000818, 0x00000000 },
+ { 0x0000081c, 0x00000000 },
+ { 0x00000820, 0x00000000 },
+ { 0x00000824, 0x00000000 },
+ { 0x00001040, 0x002ffc0f },
+ { 0x00001044, 0x002ffc0f },
+ { 0x00001048, 0x002ffc0f },
+ { 0x0000104c, 0x002ffc0f },
+ { 0x00001050, 0x002ffc0f },
+ { 0x00001054, 0x002ffc0f },
+ { 0x00001058, 0x002ffc0f },
+ { 0x0000105c, 0x002ffc0f },
+ { 0x00001060, 0x002ffc0f },
+ { 0x00001064, 0x002ffc0f },
+ { 0x00001230, 0x00000000 },
+ { 0x00001270, 0x00000000 },
+ { 0x00001038, 0x00000000 },
+ { 0x00001078, 0x00000000 },
+ { 0x000010b8, 0x00000000 },
+ { 0x000010f8, 0x00000000 },
+ { 0x00001138, 0x00000000 },
+ { 0x00001178, 0x00000000 },
+ { 0x000011b8, 0x00000000 },
+ { 0x000011f8, 0x00000000 },
+ { 0x00001238, 0x00000000 },
+ { 0x00001278, 0x00000000 },
+ { 0x000012b8, 0x00000000 },
+ { 0x000012f8, 0x00000000 },
+ { 0x00001338, 0x00000000 },
+ { 0x00001378, 0x00000000 },
+ { 0x000013b8, 0x00000000 },
+ { 0x000013f8, 0x00000000 },
+ { 0x00001438, 0x00000000 },
+ { 0x00001478, 0x00000000 },
+ { 0x000014b8, 0x00000000 },
+ { 0x000014f8, 0x00000000 },
+ { 0x00001538, 0x00000000 },
+ { 0x00001578, 0x00000000 },
+ { 0x000015b8, 0x00000000 },
+ { 0x000015f8, 0x00000000 },
+ { 0x00001638, 0x00000000 },
+ { 0x00001678, 0x00000000 },
+ { 0x000016b8, 0x00000000 },
+ { 0x000016f8, 0x00000000 },
+ { 0x00001738, 0x00000000 },
+ { 0x00001778, 0x00000000 },
+ { 0x000017b8, 0x00000000 },
+ { 0x000017f8, 0x00000000 },
+ { 0x0000103c, 0x00000000 },
+ { 0x0000107c, 0x00000000 },
+ { 0x000010bc, 0x00000000 },
+ { 0x000010fc, 0x00000000 },
+ { 0x0000113c, 0x00000000 },
+ { 0x0000117c, 0x00000000 },
+ { 0x000011bc, 0x00000000 },
+ { 0x000011fc, 0x00000000 },
+ { 0x0000123c, 0x00000000 },
+ { 0x0000127c, 0x00000000 },
+ { 0x000012bc, 0x00000000 },
+ { 0x000012fc, 0x00000000 },
+ { 0x0000133c, 0x00000000 },
+ { 0x0000137c, 0x00000000 },
+ { 0x000013bc, 0x00000000 },
+ { 0x000013fc, 0x00000000 },
+ { 0x0000143c, 0x00000000 },
+ { 0x0000147c, 0x00000000 },
+ { 0x00004030, 0x00000002 },
+ { 0x0000403c, 0x00000002 },
+ { 0x00007010, 0x00000020 },
+ { 0x00007038, 0x000004c2 },
+ { 0x00008004, 0x00000000 },
+ { 0x00008008, 0x00000000 },
+ { 0x0000800c, 0x00000000 },
+ { 0x00008018, 0x00000700 },
+ { 0x00008020, 0x00000000 },
+ { 0x00008038, 0x00000000 },
+ { 0x0000803c, 0x00000000 },
+ { 0x00008048, 0x40000000 },
+ { 0x00008054, 0x00000000 },
+ { 0x00008058, 0x00000000 },
+ { 0x0000805c, 0x000fc78f },
+ { 0x00008060, 0x0000000f },
+ { 0x00008064, 0x00000000 },
+ { 0x000080c0, 0x2a82301a },
+ { 0x000080c4, 0x05dc01e0 },
+ { 0x000080c8, 0x1f402710 },
+ { 0x000080cc, 0x01f40000 },
+ { 0x000080d0, 0x00001e00 },
+ { 0x000080d4, 0x00000000 },
+ { 0x000080d8, 0x00400000 },
+ { 0x000080e0, 0xffffffff },
+ { 0x000080e4, 0x0000ffff },
+ { 0x000080e8, 0x003f3f3f },
+ { 0x000080ec, 0x00000000 },
+ { 0x000080f0, 0x00000000 },
+ { 0x000080f4, 0x00000000 },
+ { 0x000080f8, 0x00000000 },
+ { 0x000080fc, 0x00020000 },
+ { 0x00008100, 0x00020000 },
+ { 0x00008104, 0x00000001 },
+ { 0x00008108, 0x00000052 },
+ { 0x0000810c, 0x00000000 },
+ { 0x00008110, 0x00000168 },
+ { 0x00008118, 0x000100aa },
+ { 0x0000811c, 0x00003210 },
+ { 0x00008120, 0x08f04800 },
+ { 0x00008124, 0x00000000 },
+ { 0x00008128, 0x00000000 },
+ { 0x0000812c, 0x00000000 },
+ { 0x00008130, 0x00000000 },
+ { 0x00008134, 0x00000000 },
+ { 0x00008138, 0x00000000 },
+ { 0x0000813c, 0x00000000 },
+ { 0x00008144, 0x00000000 },
+ { 0x00008168, 0x00000000 },
+ { 0x0000816c, 0x00000000 },
+ { 0x00008170, 0x32143320 },
+ { 0x00008174, 0xfaa4fa50 },
+ { 0x00008178, 0x00000100 },
+ { 0x0000817c, 0x00000000 },
+ { 0x000081c4, 0x00000000 },
+ { 0x000081d0, 0x00003210 },
+ { 0x000081ec, 0x00000000 },
+ { 0x000081f0, 0x00000000 },
+ { 0x000081f4, 0x00000000 },
+ { 0x000081f8, 0x00000000 },
+ { 0x000081fc, 0x00000000 },
+ { 0x00008200, 0x00000000 },
+ { 0x00008204, 0x00000000 },
+ { 0x00008208, 0x00000000 },
+ { 0x0000820c, 0x00000000 },
+ { 0x00008210, 0x00000000 },
+ { 0x00008214, 0x00000000 },
+ { 0x00008218, 0x00000000 },
+ { 0x0000821c, 0x00000000 },
+ { 0x00008220, 0x00000000 },
+ { 0x00008224, 0x00000000 },
+ { 0x00008228, 0x00000000 },
+ { 0x0000822c, 0x00000000 },
+ { 0x00008230, 0x00000000 },
+ { 0x00008234, 0x00000000 },
+ { 0x00008238, 0x00000000 },
+ { 0x0000823c, 0x00000000 },
+ { 0x00008240, 0x00100000 },
+ { 0x00008244, 0x0010f400 },
+ { 0x00008248, 0x00000100 },
+ { 0x0000824c, 0x0001e800 },
+ { 0x00008250, 0x00000000 },
+ { 0x00008254, 0x00000000 },
+ { 0x00008258, 0x00000000 },
+ { 0x0000825c, 0x400000ff },
+ { 0x00008260, 0x00080922 },
+ { 0x00008270, 0x00000000 },
+ { 0x00008274, 0x40000000 },
+ { 0x00008278, 0x003e4180 },
+ { 0x0000827c, 0x00000000 },
+ { 0x00008284, 0x0000002c },
+ { 0x00008288, 0x0000002c },
+ { 0x0000828c, 0x00000000 },
+ { 0x00008294, 0x00000000 },
+ { 0x00008298, 0x00000000 },
+ { 0x00008300, 0x00000000 },
+ { 0x00008304, 0x00000000 },
+ { 0x00008308, 0x00000000 },
+ { 0x0000830c, 0x00000000 },
+ { 0x00008310, 0x00000000 },
+ { 0x00008314, 0x00000000 },
+ { 0x00008318, 0x00000000 },
+ { 0x00008328, 0x00000000 },
+ { 0x0000832c, 0x00000007 },
+ { 0x00008330, 0x00000302 },
+ { 0x00008334, 0x00000e00 },
+ { 0x00008338, 0x00000000 },
+ { 0x0000833c, 0x00000000 },
+ { 0x00008340, 0x000107ff },
+ { 0x00009808, 0x00000000 },
+ { 0x0000980c, 0xad848e19 },
+ { 0x00009810, 0x7d14e000 },
+ { 0x00009814, 0x9c0a9f6b },
+ { 0x0000981c, 0x00000000 },
+ { 0x0000982c, 0x0000a000 },
+ { 0x00009830, 0x00000000 },
+ { 0x0000983c, 0x00200400 },
+ { 0x00009840, 0x206a01ae },
+ { 0x0000984c, 0x1284233c },
+ { 0x00009854, 0x00000859 },
+ { 0x00009900, 0x00000000 },
+ { 0x00009904, 0x00000000 },
+ { 0x00009908, 0x00000000 },
+ { 0x0000990c, 0x00000000 },
+ { 0x0000991c, 0x10000fff },
+ { 0x00009920, 0x05100000 },
+ { 0x0000a920, 0x05100000 },
+ { 0x0000b920, 0x05100000 },
+ { 0x00009928, 0x00000001 },
+ { 0x0000992c, 0x00000004 },
+ { 0x00009934, 0x1e1f2022 },
+ { 0x00009938, 0x0a0b0c0d },
+ { 0x0000993c, 0x00000000 },
+ { 0x00009948, 0x9280b212 },
+ { 0x0000994c, 0x00020028 },
+ { 0x00009954, 0x5f3ca3de },
+ { 0x00009958, 0x2108ecff },
+ { 0x00009940, 0x00750604 },
+ { 0x0000c95c, 0x004b6a8e },
+ { 0x0000c968, 0x000003ce },
+ { 0x00009970, 0x190fb515 },
+ { 0x00009974, 0x00000000 },
+ { 0x00009978, 0x00000001 },
+ { 0x0000997c, 0x00000000 },
+ { 0x00009980, 0x00000000 },
+ { 0x00009984, 0x00000000 },
+ { 0x00009988, 0x00000000 },
+ { 0x0000998c, 0x00000000 },
+ { 0x00009990, 0x00000000 },
+ { 0x00009994, 0x00000000 },
+ { 0x00009998, 0x00000000 },
+ { 0x0000999c, 0x00000000 },
+ { 0x000099a0, 0x00000000 },
+ { 0x000099a4, 0x00000001 },
+ { 0x000099a8, 0x201fff00 },
+ { 0x000099ac, 0x006f0000 },
+ { 0x000099b0, 0x03051000 },
+ { 0x000099dc, 0x00000000 },
+ { 0x000099e0, 0x00000200 },
+ { 0x000099e4, 0xaaaaaaaa },
+ { 0x000099e8, 0x3c466478 },
+ { 0x000099ec, 0x0cc80caa },
+ { 0x000099fc, 0x00001042 },
+ { 0x00009b00, 0x00000000 },
+ { 0x00009b04, 0x00000001 },
+ { 0x00009b08, 0x00000002 },
+ { 0x00009b0c, 0x00000003 },
+ { 0x00009b10, 0x00000004 },
+ { 0x00009b14, 0x00000005 },
+ { 0x00009b18, 0x00000008 },
+ { 0x00009b1c, 0x00000009 },
+ { 0x00009b20, 0x0000000a },
+ { 0x00009b24, 0x0000000b },
+ { 0x00009b28, 0x0000000c },
+ { 0x00009b2c, 0x0000000d },
+ { 0x00009b30, 0x00000010 },
+ { 0x00009b34, 0x00000011 },
+ { 0x00009b38, 0x00000012 },
+ { 0x00009b3c, 0x00000013 },
+ { 0x00009b40, 0x00000014 },
+ { 0x00009b44, 0x00000015 },
+ { 0x00009b48, 0x00000018 },
+ { 0x00009b4c, 0x00000019 },
+ { 0x00009b50, 0x0000001a },
+ { 0x00009b54, 0x0000001b },
+ { 0x00009b58, 0x0000001c },
+ { 0x00009b5c, 0x0000001d },
+ { 0x00009b60, 0x00000020 },
+ { 0x00009b64, 0x00000021 },
+ { 0x00009b68, 0x00000022 },
+ { 0x00009b6c, 0x00000023 },
+ { 0x00009b70, 0x00000024 },
+ { 0x00009b74, 0x00000025 },
+ { 0x00009b78, 0x00000028 },
+ { 0x00009b7c, 0x00000029 },
+ { 0x00009b80, 0x0000002a },
+ { 0x00009b84, 0x0000002b },
+ { 0x00009b88, 0x0000002c },
+ { 0x00009b8c, 0x0000002d },
+ { 0x00009b90, 0x00000030 },
+ { 0x00009b94, 0x00000031 },
+ { 0x00009b98, 0x00000032 },
+ { 0x00009b9c, 0x00000033 },
+ { 0x00009ba0, 0x00000034 },
+ { 0x00009ba4, 0x00000035 },
+ { 0x00009ba8, 0x00000035 },
+ { 0x00009bac, 0x00000035 },
+ { 0x00009bb0, 0x00000035 },
+ { 0x00009bb4, 0x00000035 },
+ { 0x00009bb8, 0x00000035 },
+ { 0x00009bbc, 0x00000035 },
+ { 0x00009bc0, 0x00000035 },
+ { 0x00009bc4, 0x00000035 },
+ { 0x00009bc8, 0x00000035 },
+ { 0x00009bcc, 0x00000035 },
+ { 0x00009bd0, 0x00000035 },
+ { 0x00009bd4, 0x00000035 },
+ { 0x00009bd8, 0x00000035 },
+ { 0x00009bdc, 0x00000035 },
+ { 0x00009be0, 0x00000035 },
+ { 0x00009be4, 0x00000035 },
+ { 0x00009be8, 0x00000035 },
+ { 0x00009bec, 0x00000035 },
+ { 0x00009bf0, 0x00000035 },
+ { 0x00009bf4, 0x00000035 },
+ { 0x00009bf8, 0x00000010 },
+ { 0x00009bfc, 0x0000001a },
+ { 0x0000a210, 0x40806333 },
+ { 0x0000a214, 0x00106c10 },
+ { 0x0000a218, 0x009c4060 },
+ { 0x0000a220, 0x018830c6 },
+ { 0x0000a224, 0x00000400 },
+ { 0x0000a228, 0x001a0bb5 },
+ { 0x0000a22c, 0x00000000 },
+ { 0x0000a234, 0x20202020 },
+ { 0x0000a238, 0x20202020 },
+ { 0x0000a23c, 0x13c889af },
+ { 0x0000a240, 0x38490a20 },
+ { 0x0000a244, 0x00007bb6 },
+ { 0x0000a248, 0x0fff3ffc },
+ { 0x0000a24c, 0x00000001 },
+ { 0x0000a250, 0x0000a000 },
+ { 0x0000a254, 0x00000000 },
+ { 0x0000a258, 0x0cc75380 },
+ { 0x0000a25c, 0x0f0f0f01 },
+ { 0x0000a260, 0xdfa91f01 },
+ { 0x0000a268, 0x00000001 },
+ { 0x0000a26c, 0x0ebae9c6 },
+ { 0x0000b26c, 0x0ebae9c6 },
+ { 0x0000c26c, 0x0ebae9c6 },
+ { 0x0000d270, 0x00820820 },
+ { 0x0000a278, 0x1ce739ce },
+ { 0x0000a27c, 0x050701ce },
+ { 0x0000a338, 0x00000000 },
+ { 0x0000a33c, 0x00000000 },
+ { 0x0000a340, 0x00000000 },
+ { 0x0000a344, 0x00000000 },
+ { 0x0000a348, 0x3fffffff },
+ { 0x0000a34c, 0x3fffffff },
+ { 0x0000a350, 0x3fffffff },
+ { 0x0000a354, 0x0003ffff },
+ { 0x0000a358, 0x79a8aa33 },
+ { 0x0000d35c, 0x07ffffef },
+ { 0x0000d360, 0x0fffffe7 },
+ { 0x0000d364, 0x17ffffe5 },
+ { 0x0000d368, 0x1fffffe4 },
+ { 0x0000d36c, 0x37ffffe3 },
+ { 0x0000d370, 0x3fffffe3 },
+ { 0x0000d374, 0x57ffffe3 },
+ { 0x0000d378, 0x5fffffe2 },
+ { 0x0000d37c, 0x7fffffe2 },
+ { 0x0000d380, 0x7f3c7bba },
+ { 0x0000d384, 0xf3307ff0 },
+ { 0x0000a388, 0x0c000000 },
+ { 0x0000a38c, 0x20202020 },
+ { 0x0000a390, 0x20202020 },
+ { 0x0000a394, 0x1ce739ce },
+ { 0x0000a398, 0x000001ce },
+ { 0x0000a39c, 0x00000001 },
+ { 0x0000a3a0, 0x00000000 },
+ { 0x0000a3a4, 0x00000000 },
+ { 0x0000a3a8, 0x00000000 },
+ { 0x0000a3ac, 0x00000000 },
+ { 0x0000a3b0, 0x00000000 },
+ { 0x0000a3b4, 0x00000000 },
+ { 0x0000a3b8, 0x00000000 },
+ { 0x0000a3bc, 0x00000000 },
+ { 0x0000a3c0, 0x00000000 },
+ { 0x0000a3c4, 0x00000000 },
+ { 0x0000a3c8, 0x00000246 },
+ { 0x0000a3cc, 0x20202020 },
+ { 0x0000a3d0, 0x20202020 },
+ { 0x0000a3d4, 0x20202020 },
+ { 0x0000a3dc, 0x1ce739ce },
+ { 0x0000a3e0, 0x000001ce },
+};
+
+static const u32 ar5416Bank0_9160[][2] = {
+ { 0x000098b0, 0x1e5795e5 },
+ { 0x000098e0, 0x02008020 },
+};
+
+static const u32 ar5416BB_RfGain_9160[][3] = {
+ { 0x00009a00, 0x00000000, 0x00000000 },
+ { 0x00009a04, 0x00000040, 0x00000040 },
+ { 0x00009a08, 0x00000080, 0x00000080 },
+ { 0x00009a0c, 0x000001a1, 0x00000141 },
+ { 0x00009a10, 0x000001e1, 0x00000181 },
+ { 0x00009a14, 0x00000021, 0x000001c1 },
+ { 0x00009a18, 0x00000061, 0x00000001 },
+ { 0x00009a1c, 0x00000168, 0x00000041 },
+ { 0x00009a20, 0x000001a8, 0x000001a8 },
+ { 0x00009a24, 0x000001e8, 0x000001e8 },
+ { 0x00009a28, 0x00000028, 0x00000028 },
+ { 0x00009a2c, 0x00000068, 0x00000068 },
+ { 0x00009a30, 0x00000189, 0x000000a8 },
+ { 0x00009a34, 0x000001c9, 0x00000169 },
+ { 0x00009a38, 0x00000009, 0x000001a9 },
+ { 0x00009a3c, 0x00000049, 0x000001e9 },
+ { 0x00009a40, 0x00000089, 0x00000029 },
+ { 0x00009a44, 0x00000170, 0x00000069 },
+ { 0x00009a48, 0x000001b0, 0x00000190 },
+ { 0x00009a4c, 0x000001f0, 0x000001d0 },
+ { 0x00009a50, 0x00000030, 0x00000010 },
+ { 0x00009a54, 0x00000070, 0x00000050 },
+ { 0x00009a58, 0x00000191, 0x00000090 },
+ { 0x00009a5c, 0x000001d1, 0x00000151 },
+ { 0x00009a60, 0x00000011, 0x00000191 },
+ { 0x00009a64, 0x00000051, 0x000001d1 },
+ { 0x00009a68, 0x00000091, 0x00000011 },
+ { 0x00009a6c, 0x000001b8, 0x00000051 },
+ { 0x00009a70, 0x000001f8, 0x00000198 },
+ { 0x00009a74, 0x00000038, 0x000001d8 },
+ { 0x00009a78, 0x00000078, 0x00000018 },
+ { 0x00009a7c, 0x00000199, 0x00000058 },
+ { 0x00009a80, 0x000001d9, 0x00000098 },
+ { 0x00009a84, 0x00000019, 0x00000159 },
+ { 0x00009a88, 0x00000059, 0x00000199 },
+ { 0x00009a8c, 0x00000099, 0x000001d9 },
+ { 0x00009a90, 0x000000d9, 0x00000019 },
+ { 0x00009a94, 0x000000f9, 0x00000059 },
+ { 0x00009a98, 0x000000f9, 0x00000099 },
+ { 0x00009a9c, 0x000000f9, 0x000000d9 },
+ { 0x00009aa0, 0x000000f9, 0x000000f9 },
+ { 0x00009aa4, 0x000000f9, 0x000000f9 },
+ { 0x00009aa8, 0x000000f9, 0x000000f9 },
+ { 0x00009aac, 0x000000f9, 0x000000f9 },
+ { 0x00009ab0, 0x000000f9, 0x000000f9 },
+ { 0x00009ab4, 0x000000f9, 0x000000f9 },
+ { 0x00009ab8, 0x000000f9, 0x000000f9 },
+ { 0x00009abc, 0x000000f9, 0x000000f9 },
+ { 0x00009ac0, 0x000000f9, 0x000000f9 },
+ { 0x00009ac4, 0x000000f9, 0x000000f9 },
+ { 0x00009ac8, 0x000000f9, 0x000000f9 },
+ { 0x00009acc, 0x000000f9, 0x000000f9 },
+ { 0x00009ad0, 0x000000f9, 0x000000f9 },
+ { 0x00009ad4, 0x000000f9, 0x000000f9 },
+ { 0x00009ad8, 0x000000f9, 0x000000f9 },
+ { 0x00009adc, 0x000000f9, 0x000000f9 },
+ { 0x00009ae0, 0x000000f9, 0x000000f9 },
+ { 0x00009ae4, 0x000000f9, 0x000000f9 },
+ { 0x00009ae8, 0x000000f9, 0x000000f9 },
+ { 0x00009aec, 0x000000f9, 0x000000f9 },
+ { 0x00009af0, 0x000000f9, 0x000000f9 },
+ { 0x00009af4, 0x000000f9, 0x000000f9 },
+ { 0x00009af8, 0x000000f9, 0x000000f9 },
+ { 0x00009afc, 0x000000f9, 0x000000f9 },
+};
+
+static const u32 ar5416Bank1_9160[][2] = {
+ { 0x000098b0, 0x02108421 },
+ { 0x000098ec, 0x00000008 },
+};
+
+static const u32 ar5416Bank2_9160[][2] = {
+ { 0x000098b0, 0x0e73ff17 },
+ { 0x000098e0, 0x00000420 },
+};
+
+static const u32 ar5416Bank3_9160[][3] = {
+ { 0x000098f0, 0x01400018, 0x01c00018 },
+};
+
+static const u32 ar5416Bank6_9160[][3] = {
+
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x40ff0000, 0x40ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x004210a2, 0x004210a2 },
+ { 0x0000989c, 0x0014008f, 0x0014008f },
+ { 0x0000989c, 0x00c40003, 0x00c40003 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x0001805e, 0x0001805e },
+ { 0x0000989c, 0x0000c0ab, 0x0000c0ab },
+ { 0x0000989c, 0x000000f1, 0x000000f1 },
+ { 0x0000989c, 0x00002081, 0x00002081 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+static const u32 ar5416Bank6TPC_9160[][3] = {
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00000000, 0x00000000 },
+ { 0x0000989c, 0x00e00000, 0x00e00000 },
+ { 0x0000989c, 0x005e0000, 0x005e0000 },
+ { 0x0000989c, 0x00120000, 0x00120000 },
+ { 0x0000989c, 0x00620000, 0x00620000 },
+ { 0x0000989c, 0x00020000, 0x00020000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x40ff0000, 0x40ff0000 },
+ { 0x0000989c, 0x005f0000, 0x005f0000 },
+ { 0x0000989c, 0x00870000, 0x00870000 },
+ { 0x0000989c, 0x00f90000, 0x00f90000 },
+ { 0x0000989c, 0x007b0000, 0x007b0000 },
+ { 0x0000989c, 0x00ff0000, 0x00ff0000 },
+ { 0x0000989c, 0x00f50000, 0x00f50000 },
+ { 0x0000989c, 0x00dc0000, 0x00dc0000 },
+ { 0x0000989c, 0x00110000, 0x00110000 },
+ { 0x0000989c, 0x006100a8, 0x006100a8 },
+ { 0x0000989c, 0x00423022, 0x00423022 },
+ { 0x0000989c, 0x2014008f, 0x2014008f },
+ { 0x0000989c, 0x00c40002, 0x00c40002 },
+ { 0x0000989c, 0x003000f2, 0x003000f2 },
+ { 0x0000989c, 0x00440016, 0x00440016 },
+ { 0x0000989c, 0x00410040, 0x00410040 },
+ { 0x0000989c, 0x0001805e, 0x0001805e },
+ { 0x0000989c, 0x0000c0ab, 0x0000c0ab },
+ { 0x0000989c, 0x000000e1, 0x000000e1 },
+ { 0x0000989c, 0x00007080, 0x00007080 },
+ { 0x0000989c, 0x000000d4, 0x000000d4 },
+ { 0x000098d0, 0x0000000f, 0x0010000f },
+};
+
+static const u32 ar5416Bank7_9160[][2] = {
+ { 0x0000989c, 0x00000500 },
+ { 0x0000989c, 0x00000800 },
+ { 0x000098cc, 0x0000000e },
+};
+
+
+static u32 ar5416Addac_9160[][2] = {
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x000000c0 },
+ {0x0000989c, 0x00000018 },
+ {0x0000989c, 0x00000004 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x000000c0 },
+ {0x0000989c, 0x00000019 },
+ {0x0000989c, 0x00000004 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000004 },
+ {0x0000989c, 0x00000003 },
+ {0x0000989c, 0x00000008 },
+ {0x0000989c, 0x00000000 },
+ {0x000098cc, 0x00000000 },
+};
+
+
+static u32 ar5416Addac_91601_1[][2] = {
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x000000c0 },
+ {0x0000989c, 0x00000018 },
+ {0x0000989c, 0x00000004 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x000000c0 },
+ {0x0000989c, 0x00000019 },
+ {0x0000989c, 0x00000004 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x0000989c, 0x00000000 },
+ {0x000098cc, 0x00000000 },
+};
+
+
+
+static const u32 ar9280Modes_9280[][6] = {
+ { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 },
+ { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 },
+ { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 },
+ { 0x000010f0, 0x0000a000, 0x00014000, 0x00016000, 0x0000b000, 0x00014008 },
+ { 0x00008014, 0x03e803e8, 0x07d007d0, 0x10801080, 0x08400840, 0x06e006e0 },
+ { 0x0000801c, 0x128d8027, 0x128d804f, 0x12e00057, 0x12e0002b, 0x0988004f },
+ { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 },
+ { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 },
+ { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 },
+ { 0x00009844, 0x1372161e, 0x1372161e, 0x137216a0, 0x137216a0, 0x137216a0 },
+ { 0x00009848, 0x00028566, 0x00028566, 0x00028563, 0x00028563, 0x00028563 },
+ { 0x0000a848, 0x00028566, 0x00028566, 0x00028563, 0x00028563, 0x00028563 },
+ { 0x00009850, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2 },
+ { 0x00009858, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e, 0x7ec82d2e },
+ { 0x0000985c, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e },
+ { 0x00009860, 0x00049d18, 0x00049d18, 0x00049d20, 0x00049d20, 0x00049d18 },
+ { 0x0000c864, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00, 0x0001ce00 },
+ { 0x00009868, 0x5ac64190, 0x5ac64190, 0x5ac64190, 0x5ac64190, 0x5ac64190 },
+ { 0x0000986c, 0x06903081, 0x06903081, 0x06903881, 0x06903881, 0x06903881 },
+ { 0x00009914, 0x000007d0, 0x000007d0, 0x00000898, 0x00000898, 0x000007d0 },
+ { 0x00009918, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b, 0x00000016 },
+ { 0x00009924, 0xd00a8a07, 0xd00a8a07, 0xd00a8a0d, 0xd00a8a0d, 0xd00a8a0d },
+ { 0x00009944, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010 },
+ { 0x00009960, 0x00000010, 0x00000010, 0x00000010, 0x00000010, 0x00000010 },
+ { 0x0000a960, 0x00000010, 0x00000010, 0x00000010, 0x00000010, 0x00000010 },
+ { 0x00009964, 0x00000210, 0x00000210, 0x00000210, 0x00000210, 0x00000210 },
+ { 0x0000c9b8, 0x0000001a, 0x0000001a, 0x0000001a, 0x0000001a, 0x0000001a },
+ { 0x0000c9bc, 0x00000600, 0x00000600, 0x00000c00, 0x00000c00, 0x00000c00 },
+ { 0x000099c0, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4 },
+ { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 },
+ { 0x000099c8, 0x60f6532c, 0x60f6532c, 0x60f6532c, 0x60f6532c, 0x60f6532c },
+ { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 },
+ { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 },
+ { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x000099d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x00009a00, 0x00008184, 0x00008184, 0x00000214, 0x00000214, 0x00000214 },
+ { 0x00009a04, 0x00008188, 0x00008188, 0x00000218, 0x00000218, 0x00000218 },
+ { 0x00009a08, 0x0000818c, 0x0000818c, 0x00000224, 0x00000224, 0x00000224 },
+ { 0x00009a0c, 0x00008190, 0x00008190, 0x00000228, 0x00000228, 0x00000228 },
+ { 0x00009a10, 0x00008194, 0x00008194, 0x0000022c, 0x0000022c, 0x0000022c },
+ { 0x00009a14, 0x00008200, 0x00008200, 0x00000230, 0x00000230, 0x00000230 },
+ { 0x00009a18, 0x00008204, 0x00008204, 0x000002a4, 0x000002a4, 0x000002a4 },
+ { 0x00009a1c, 0x00008208, 0x00008208, 0x000002a8, 0x000002a8, 0x000002a8 },
+ { 0x00009a20, 0x0000820c, 0x0000820c, 0x000002ac, 0x000002ac, 0x000002ac },
+ { 0x00009a24, 0x00008210, 0x00008210, 0x000002b0, 0x000002b0, 0x000002b0 },
+ { 0x00009a28, 0x00008214, 0x00008214, 0x000002b4, 0x000002b4, 0x000002b4 },
+ { 0x00009a2c, 0x00008280, 0x00008280, 0x000002b8, 0x000002b8, 0x000002b8 },
+ { 0x00009a30, 0x00008284, 0x00008284, 0x00000390, 0x00000390, 0x00000390 },
+ { 0x00009a34, 0x00008288, 0x00008288, 0x00000394, 0x00000394, 0x00000394 },
+ { 0x00009a38, 0x0000828c, 0x0000828c, 0x00000398, 0x00000398, 0x00000398 },
+ { 0x00009a3c, 0x00008290, 0x00008290, 0x00000334, 0x00000334, 0x00000334 },
+ { 0x00009a40, 0x00008300, 0x00008300, 0x00000338, 0x00000338, 0x00000338 },
+ { 0x00009a44, 0x00008304, 0x00008304, 0x000003ac, 0x000003ac, 0x000003ac },
+ { 0x00009a48, 0x00008308, 0x00008308, 0x000003b0, 0x000003b0, 0x000003b0 },
+ { 0x00009a4c, 0x0000830c, 0x0000830c, 0x000003b4, 0x000003b4, 0x000003b4 },
+ { 0x00009a50, 0x00008310, 0x00008310, 0x000003b8, 0x000003b8, 0x000003b8 },
+ { 0x00009a54, 0x00008314, 0x00008314, 0x000003a5, 0x000003a5, 0x000003a5 },
+ { 0x00009a58, 0x00008380, 0x00008380, 0x000003a9, 0x000003a9, 0x000003a9 },
+ { 0x00009a5c, 0x00008384, 0x00008384, 0x000003ad, 0x000003ad, 0x000003ad },
+ { 0x00009a60, 0x00008388, 0x00008388, 0x00008194, 0x00008194, 0x00008194 },
+ { 0x00009a64, 0x0000838c, 0x0000838c, 0x000081a0, 0x000081a0, 0x000081a0 },
+ { 0x00009a68, 0x00008390, 0x00008390, 0x0000820c, 0x0000820c, 0x0000820c },
+ { 0x00009a6c, 0x00008394, 0x00008394, 0x000081a8, 0x000081a8, 0x000081a8 },
+ { 0x00009a70, 0x0000a380, 0x0000a380, 0x00008284, 0x00008284, 0x00008284 },
+ { 0x00009a74, 0x0000a384, 0x0000a384, 0x00008288, 0x00008288, 0x00008288 },
+ { 0x00009a78, 0x0000a388, 0x0000a388, 0x00008224, 0x00008224, 0x00008224 },
+ { 0x00009a7c, 0x0000a38c, 0x0000a38c, 0x00008290, 0x00008290, 0x00008290 },
+ { 0x00009a80, 0x0000a390, 0x0000a390, 0x00008300, 0x00008300, 0x00008300 },
+ { 0x00009a84, 0x0000a394, 0x0000a394, 0x00008304, 0x00008304, 0x00008304 },
+ { 0x00009a88, 0x0000a780, 0x0000a780, 0x00008308, 0x00008308, 0x00008308 },
+ { 0x00009a8c, 0x0000a784, 0x0000a784, 0x0000830c, 0x0000830c, 0x0000830c },
+ { 0x00009a90, 0x0000a788, 0x0000a788, 0x00008380, 0x00008380, 0x00008380 },
+ { 0x00009a94, 0x0000a78c, 0x0000a78c, 0x00008384, 0x00008384, 0x00008384 },
+ { 0x00009a98, 0x0000a790, 0x0000a790, 0x00008700, 0x00008700, 0x00008700 },
+ { 0x00009a9c, 0x0000a794, 0x0000a794, 0x00008704, 0x00008704, 0x00008704 },
+ { 0x00009aa0, 0x0000ab84, 0x0000ab84, 0x00008708, 0x00008708, 0x00008708 },
+ { 0x00009aa4, 0x0000ab88, 0x0000ab88, 0x0000870c, 0x0000870c, 0x0000870c },
+ { 0x00009aa8, 0x0000ab8c, 0x0000ab8c, 0x00008780, 0x00008780, 0x00008780 },
+ { 0x00009aac, 0x0000ab90, 0x0000ab90, 0x00008784, 0x00008784, 0x00008784 },
+ { 0x00009ab0, 0x0000ab94, 0x0000ab94, 0x00008b00, 0x00008b00, 0x00008b00 },
+ { 0x00009ab4, 0x0000af80, 0x0000af80, 0x00008b04, 0x00008b04, 0x00008b04 },
+ { 0x00009ab8, 0x0000af84, 0x0000af84, 0x00008b08, 0x00008b08, 0x00008b08 },
+ { 0x00009abc, 0x0000af88, 0x0000af88, 0x00008b0c, 0x00008b0c, 0x00008b0c },
+ { 0x00009ac0, 0x0000af8c, 0x0000af8c, 0x00008b80, 0x00008b80, 0x00008b80 },
+ { 0x00009ac4, 0x0000af90, 0x0000af90, 0x00008b84, 0x00008b84, 0x00008b84 },
+ { 0x00009ac8, 0x0000af94, 0x0000af94, 0x00008b88, 0x00008b88, 0x00008b88 },
+ { 0x00009acc, 0x0000b380, 0x0000b380, 0x00008b8c, 0x00008b8c, 0x00008b8c },
+ { 0x00009ad0, 0x0000b384, 0x0000b384, 0x00008b90, 0x00008b90, 0x00008b90 },
+ { 0x00009ad4, 0x0000b388, 0x0000b388, 0x00008f80, 0x00008f80, 0x00008f80 },
+ { 0x00009ad8, 0x0000b38c, 0x0000b38c, 0x00008f84, 0x00008f84, 0x00008f84 },
+ { 0x00009adc, 0x0000b390, 0x0000b390, 0x00008f88, 0x00008f88, 0x00008f88 },
+ { 0x00009ae0, 0x0000b394, 0x0000b394, 0x00008f8c, 0x00008f8c, 0x00008f8c },
+ { 0x00009ae4, 0x0000b398, 0x0000b398, 0x00008f90, 0x00008f90, 0x00008f90 },
+ { 0x00009ae8, 0x0000b780, 0x0000b780, 0x0000930c, 0x0000930c, 0x0000930c },
+ { 0x00009aec, 0x0000b784, 0x0000b784, 0x00009310, 0x00009310, 0x00009310 },
+ { 0x00009af0, 0x0000b788, 0x0000b788, 0x00009384, 0x00009384, 0x00009384 },
+ { 0x00009af4, 0x0000b78c, 0x0000b78c, 0x00009388, 0x00009388, 0x00009388 },
+ { 0x00009af8, 0x0000b790, 0x0000b790, 0x00009324, 0x00009324, 0x00009324 },
+ { 0x00009afc, 0x0000b794, 0x0000b794, 0x00009704, 0x00009704, 0x00009704 },
+ { 0x00009b00, 0x0000b798, 0x0000b798, 0x000096a4, 0x000096a4, 0x000096a4 },
+ { 0x00009b04, 0x0000d784, 0x0000d784, 0x000096a8, 0x000096a8, 0x000096a8 },
+ { 0x00009b08, 0x0000d788, 0x0000d788, 0x00009710, 0x00009710, 0x00009710 },
+ { 0x00009b0c, 0x0000d78c, 0x0000d78c, 0x00009714, 0x00009714, 0x00009714 },
+ { 0x00009b10, 0x0000d790, 0x0000d790, 0x00009720, 0x00009720, 0x00009720 },
+ { 0x00009b14, 0x0000f780, 0x0000f780, 0x00009724, 0x00009724, 0x00009724 },
+ { 0x00009b18, 0x0000f784, 0x0000f784, 0x00009728, 0x00009728, 0x00009728 },
+ { 0x00009b1c, 0x0000f788, 0x0000f788, 0x0000972c, 0x0000972c, 0x0000972c },
+ { 0x00009b20, 0x0000f78c, 0x0000f78c, 0x000097a0, 0x000097a0, 0x000097a0 },
+ { 0x00009b24, 0x0000f790, 0x0000f790, 0x000097a4, 0x000097a4, 0x000097a4 },
+ { 0x00009b28, 0x0000f794, 0x0000f794, 0x000097a8, 0x000097a8, 0x000097a8 },
+ { 0x00009b2c, 0x0000f7a4, 0x0000f7a4, 0x000097b0, 0x000097b0, 0x000097b0 },
+ { 0x00009b30, 0x0000f7a8, 0x0000f7a8, 0x000097b4, 0x000097b4, 0x000097b4 },
+ { 0x00009b34, 0x0000f7ac, 0x0000f7ac, 0x000097b8, 0x000097b8, 0x000097b8 },
+ { 0x00009b38, 0x0000f7b0, 0x0000f7b0, 0x000097a5, 0x000097a5, 0x000097a5 },
+ { 0x00009b3c, 0x0000f7b4, 0x0000f7b4, 0x000097a9, 0x000097a9, 0x000097a9 },
+ { 0x00009b40, 0x0000f7a1, 0x0000f7a1, 0x000097ad, 0x000097ad, 0x000097ad },
+ { 0x00009b44, 0x0000f7a5, 0x0000f7a5, 0x000097b1, 0x000097b1, 0x000097b1 },
+ { 0x00009b48, 0x0000f7a9, 0x0000f7a9, 0x000097b5, 0x000097b5, 0x000097b5 },
+ { 0x00009b4c, 0x0000f7ad, 0x0000f7ad, 0x000097b9, 0x000097b9, 0x000097b9 },
+ { 0x00009b50, 0x0000f7b1, 0x0000f7b1, 0x000097c5, 0x000097c5, 0x000097c5 },
+ { 0x00009b54, 0x0000f7b5, 0x0000f7b5, 0x000097c9, 0x000097c9, 0x000097c9 },
+ { 0x00009b58, 0x0000f7c5, 0x0000f7c5, 0x000097d1, 0x000097d1, 0x000097d1 },
+ { 0x00009b5c, 0x0000f7c9, 0x0000f7c9, 0x000097d5, 0x000097d5, 0x000097d5 },
+ { 0x00009b60, 0x0000f7cd, 0x0000f7cd, 0x000097d9, 0x000097d9, 0x000097d9 },
+ { 0x00009b64, 0x0000f7d1, 0x0000f7d1, 0x000097c6, 0x000097c6, 0x000097c6 },
+ { 0x00009b68, 0x0000f7d5, 0x0000f7d5, 0x000097ca, 0x000097ca, 0x000097ca },
+ { 0x00009b6c, 0x0000f7c2, 0x0000f7c2, 0x000097ce, 0x000097ce, 0x000097ce },
+ { 0x00009b70, 0x0000f7c6, 0x0000f7c6, 0x000097d2, 0x000097d2, 0x000097d2 },
+ { 0x00009b74, 0x0000f7ca, 0x0000f7ca, 0x000097d6, 0x000097d6, 0x000097d6 },
+ { 0x00009b78, 0x0000f7ce, 0x0000f7ce, 0x000097c3, 0x000097c3, 0x000097c3 },
+ { 0x00009b7c, 0x0000f7d2, 0x0000f7d2, 0x000097c7, 0x000097c7, 0x000097c7 },
+ { 0x00009b80, 0x0000f7d6, 0x0000f7d6, 0x000097cb, 0x000097cb, 0x000097cb },
+ { 0x00009b84, 0x0000f7c3, 0x0000f7c3, 0x000097cf, 0x000097cf, 0x000097cf },
+ { 0x00009b88, 0x0000f7c7, 0x0000f7c7, 0x000097d7, 0x000097d7, 0x000097d7 },
+ { 0x00009b8c, 0x0000f7cb, 0x0000f7cb, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b90, 0x0000f7d3, 0x0000f7d3, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b94, 0x0000f7d7, 0x0000f7d7, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b98, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b9c, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bac, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bbc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bcc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bdc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bec, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bfc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x0000a204, 0x00000444, 0x00000444, 0x00000444, 0x00000444, 0x00000444 },
+ { 0x0000a208, 0x803e4788, 0x803e4788, 0x803e4788, 0x803e4788, 0x803e4788 },
+ { 0x0000a20c, 0x000c6019, 0x000c6019, 0x000c6019, 0x000c6019, 0x000c6019 },
+ { 0x0000b20c, 0x000c6019, 0x000c6019, 0x000c6019, 0x000c6019, 0x000c6019 },
+ { 0x0000a21c, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a, 0x1883800a },
+ { 0x0000a230, 0x00000000, 0x00000000, 0x00000210, 0x00000108, 0x00000000 },
+ { 0x0000a274, 0x0a19c652, 0x0a19c652, 0x0a1aa652, 0x0a1aa652, 0x0a1aa652 },
+ { 0x0000a300, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a304, 0x00003002, 0x00003002, 0x00003002, 0x00003002, 0x00003002 },
+ { 0x0000a308, 0x00006004, 0x00006004, 0x00008009, 0x00008009, 0x00008009 },
+ { 0x0000a30c, 0x0000a006, 0x0000a006, 0x0000b00b, 0x0000b00b, 0x0000b00b },
+ { 0x0000a310, 0x0000e012, 0x0000e012, 0x0000e012, 0x0000e012, 0x0000e012 },
+ { 0x0000a314, 0x00011014, 0x00011014, 0x00012048, 0x00012048, 0x00012048 },
+ { 0x0000a318, 0x0001504a, 0x0001504a, 0x0001604a, 0x0001604a, 0x0001604a },
+ { 0x0000a31c, 0x0001904c, 0x0001904c, 0x0001a211, 0x0001a211, 0x0001a211 },
+ { 0x0000a320, 0x0001c04e, 0x0001c04e, 0x0001e213, 0x0001e213, 0x0001e213 },
+ { 0x0000a324, 0x00020092, 0x00020092, 0x0002121b, 0x0002121b, 0x0002121b },
+ { 0x0000a328, 0x0002410a, 0x0002410a, 0x00024412, 0x00024412, 0x00024412 },
+ { 0x0000a32c, 0x0002710c, 0x0002710c, 0x00028414, 0x00028414, 0x00028414 },
+ { 0x0000a330, 0x0002b18b, 0x0002b18b, 0x0002b44a, 0x0002b44a, 0x0002b44a },
+ { 0x0000a334, 0x0002e1cc, 0x0002e1cc, 0x00030649, 0x00030649, 0x00030649 },
+ { 0x0000a338, 0x000321ec, 0x000321ec, 0x0003364b, 0x0003364b, 0x0003364b },
+ { 0x0000a33c, 0x000321ec, 0x000321ec, 0x00038a49, 0x00038a49, 0x00038a49 },
+ { 0x0000a340, 0x000321ec, 0x000321ec, 0x0003be48, 0x0003be48, 0x0003be48 },
+ { 0x0000a344, 0x000321ec, 0x000321ec, 0x0003ee4a, 0x0003ee4a, 0x0003ee4a },
+ { 0x0000a348, 0x000321ec, 0x000321ec, 0x00042e88, 0x00042e88, 0x00042e88 },
+ { 0x0000a34c, 0x000321ec, 0x000321ec, 0x00046e8a, 0x00046e8a, 0x00046e8a },
+ { 0x0000a350, 0x000321ec, 0x000321ec, 0x00049ec9, 0x00049ec9, 0x00049ec9 },
+ { 0x0000a354, 0x000321ec, 0x000321ec, 0x0004bf42, 0x0004bf42, 0x0004bf42 },
+ { 0x0000784c, 0x0e4f048c, 0x0e4f048c, 0x0e4d048c, 0x0e4d048c, 0x0e4d048c },
+ { 0x00007854, 0x12031828, 0x12031828, 0x12035828, 0x12035828, 0x12035828 },
+ { 0x00007870, 0x807ec400, 0x807ec400, 0x807ec000, 0x807ec000, 0x807ec000 },
+ { 0x0000788c, 0x00010000, 0x00010000, 0x00110000, 0x00110000, 0x00110000 },
+};
+
+static const u32 ar9280Common_9280[][2] = {
+ { 0x0000000c, 0x00000000 },
+ { 0x00000030, 0x00020015 },
+ { 0x00000034, 0x00000005 },
+ { 0x00000040, 0x00000000 },
+ { 0x00000044, 0x00000008 },
+ { 0x00000048, 0x00000008 },
+ { 0x0000004c, 0x00000010 },
+ { 0x00000050, 0x00000000 },
+ { 0x00000054, 0x0000001f },
+ { 0x00000800, 0x00000000 },
+ { 0x00000804, 0x00000000 },
+ { 0x00000808, 0x00000000 },
+ { 0x0000080c, 0x00000000 },
+ { 0x00000810, 0x00000000 },
+ { 0x00000814, 0x00000000 },
+ { 0x00000818, 0x00000000 },
+ { 0x0000081c, 0x00000000 },
+ { 0x00000820, 0x00000000 },
+ { 0x00000824, 0x00000000 },
+ { 0x00001040, 0x002ffc0f },
+ { 0x00001044, 0x002ffc0f },
+ { 0x00001048, 0x002ffc0f },
+ { 0x0000104c, 0x002ffc0f },
+ { 0x00001050, 0x002ffc0f },
+ { 0x00001054, 0x002ffc0f },
+ { 0x00001058, 0x002ffc0f },
+ { 0x0000105c, 0x002ffc0f },
+ { 0x00001060, 0x002ffc0f },
+ { 0x00001064, 0x002ffc0f },
+ { 0x00001230, 0x00000000 },
+ { 0x00001270, 0x00000000 },
+ { 0x00001038, 0x00000000 },
+ { 0x00001078, 0x00000000 },
+ { 0x000010b8, 0x00000000 },
+ { 0x000010f8, 0x00000000 },
+ { 0x00001138, 0x00000000 },
+ { 0x00001178, 0x00000000 },
+ { 0x000011b8, 0x00000000 },
+ { 0x000011f8, 0x00000000 },
+ { 0x00001238, 0x00000000 },
+ { 0x00001278, 0x00000000 },
+ { 0x000012b8, 0x00000000 },
+ { 0x000012f8, 0x00000000 },
+ { 0x00001338, 0x00000000 },
+ { 0x00001378, 0x00000000 },
+ { 0x000013b8, 0x00000000 },
+ { 0x000013f8, 0x00000000 },
+ { 0x00001438, 0x00000000 },
+ { 0x00001478, 0x00000000 },
+ { 0x000014b8, 0x00000000 },
+ { 0x000014f8, 0x00000000 },
+ { 0x00001538, 0x00000000 },
+ { 0x00001578, 0x00000000 },
+ { 0x000015b8, 0x00000000 },
+ { 0x000015f8, 0x00000000 },
+ { 0x00001638, 0x00000000 },
+ { 0x00001678, 0x00000000 },
+ { 0x000016b8, 0x00000000 },
+ { 0x000016f8, 0x00000000 },
+ { 0x00001738, 0x00000000 },
+ { 0x00001778, 0x00000000 },
+ { 0x000017b8, 0x00000000 },
+ { 0x000017f8, 0x00000000 },
+ { 0x0000103c, 0x00000000 },
+ { 0x0000107c, 0x00000000 },
+ { 0x000010bc, 0x00000000 },
+ { 0x000010fc, 0x00000000 },
+ { 0x0000113c, 0x00000000 },
+ { 0x0000117c, 0x00000000 },
+ { 0x000011bc, 0x00000000 },
+ { 0x000011fc, 0x00000000 },
+ { 0x0000123c, 0x00000000 },
+ { 0x0000127c, 0x00000000 },
+ { 0x000012bc, 0x00000000 },
+ { 0x000012fc, 0x00000000 },
+ { 0x0000133c, 0x00000000 },
+ { 0x0000137c, 0x00000000 },
+ { 0x000013bc, 0x00000000 },
+ { 0x000013fc, 0x00000000 },
+ { 0x0000143c, 0x00000000 },
+ { 0x0000147c, 0x00000000 },
+ { 0x00004030, 0x00000002 },
+ { 0x0000403c, 0x00000002 },
+ { 0x00004024, 0x0000001f },
+ { 0x00007010, 0x00000033 },
+ { 0x00007038, 0x000004c2 },
+ { 0x00008004, 0x00000000 },
+ { 0x00008008, 0x00000000 },
+ { 0x0000800c, 0x00000000 },
+ { 0x00008018, 0x00000700 },
+ { 0x00008020, 0x00000000 },
+ { 0x00008038, 0x00000000 },
+ { 0x0000803c, 0x00000000 },
+ { 0x00008048, 0x40000000 },
+ { 0x00008054, 0x00000000 },
+ { 0x00008058, 0x00000000 },
+ { 0x0000805c, 0x000fc78f },
+ { 0x00008060, 0x0000000f },
+ { 0x00008064, 0x00000000 },
+ { 0x00008070, 0x00000000 },
+ { 0x000080c0, 0x2a82301a },
+ { 0x000080c4, 0x05dc01e0 },
+ { 0x000080c8, 0x1f402710 },
+ { 0x000080cc, 0x01f40000 },
+ { 0x000080d0, 0x00001e00 },
+ { 0x000080d4, 0x00000000 },
+ { 0x000080d8, 0x00400000 },
+ { 0x000080e0, 0xffffffff },
+ { 0x000080e4, 0x0000ffff },
+ { 0x000080e8, 0x003f3f3f },
+ { 0x000080ec, 0x00000000 },
+ { 0x000080f0, 0x00000000 },
+ { 0x000080f4, 0x00000000 },
+ { 0x000080f8, 0x00000000 },
+ { 0x000080fc, 0x00020000 },
+ { 0x00008100, 0x00020000 },
+ { 0x00008104, 0x00000001 },
+ { 0x00008108, 0x00000052 },
+ { 0x0000810c, 0x00000000 },
+ { 0x00008110, 0x00000168 },
+ { 0x00008118, 0x000100aa },
+ { 0x0000811c, 0x00003210 },
+ { 0x00008120, 0x08f04800 },
+ { 0x00008124, 0x00000000 },
+ { 0x00008128, 0x00000000 },
+ { 0x0000812c, 0x00000000 },
+ { 0x00008130, 0x00000000 },
+ { 0x00008134, 0x00000000 },
+ { 0x00008138, 0x00000000 },
+ { 0x0000813c, 0x00000000 },
+ { 0x00008144, 0x00000000 },
+ { 0x00008168, 0x00000000 },
+ { 0x0000816c, 0x00000000 },
+ { 0x00008170, 0x32143320 },
+ { 0x00008174, 0xfaa4fa50 },
+ { 0x00008178, 0x00000100 },
+ { 0x0000817c, 0x00000000 },
+ { 0x000081c4, 0x00000000 },
+ { 0x000081d0, 0x00003210 },
+ { 0x000081ec, 0x00000000 },
+ { 0x000081f0, 0x00000000 },
+ { 0x000081f4, 0x00000000 },
+ { 0x000081f8, 0x00000000 },
+ { 0x000081fc, 0x00000000 },
+ { 0x00008200, 0x00000000 },
+ { 0x00008204, 0x00000000 },
+ { 0x00008208, 0x00000000 },
+ { 0x0000820c, 0x00000000 },
+ { 0x00008210, 0x00000000 },
+ { 0x00008214, 0x00000000 },
+ { 0x00008218, 0x00000000 },
+ { 0x0000821c, 0x00000000 },
+ { 0x00008220, 0x00000000 },
+ { 0x00008224, 0x00000000 },
+ { 0x00008228, 0x00000000 },
+ { 0x0000822c, 0x00000000 },
+ { 0x00008230, 0x00000000 },
+ { 0x00008234, 0x00000000 },
+ { 0x00008238, 0x00000000 },
+ { 0x0000823c, 0x00000000 },
+ { 0x00008240, 0x00100000 },
+ { 0x00008244, 0x0010f400 },
+ { 0x00008248, 0x00000100 },
+ { 0x0000824c, 0x0001e800 },
+ { 0x00008250, 0x00000000 },
+ { 0x00008254, 0x00000000 },
+ { 0x00008258, 0x00000000 },
+ { 0x0000825c, 0x400000ff },
+ { 0x00008260, 0x00080922 },
+ { 0x00008270, 0x00000000 },
+ { 0x00008274, 0x40000000 },
+ { 0x00008278, 0x003e4180 },
+ { 0x0000827c, 0x00000000 },
+ { 0x00008284, 0x0000002c },
+ { 0x00008288, 0x0000002c },
+ { 0x0000828c, 0x00000000 },
+ { 0x00008294, 0x00000000 },
+ { 0x00008298, 0x00000000 },
+ { 0x00008300, 0x00000000 },
+ { 0x00008304, 0x00000000 },
+ { 0x00008308, 0x00000000 },
+ { 0x0000830c, 0x00000000 },
+ { 0x00008310, 0x00000000 },
+ { 0x00008314, 0x00000000 },
+ { 0x00008318, 0x00000000 },
+ { 0x00008328, 0x00000000 },
+ { 0x0000832c, 0x00000007 },
+ { 0x00008330, 0x00000302 },
+ { 0x00008334, 0x00000e00 },
+ { 0x00008338, 0x00000000 },
+ { 0x0000833c, 0x00000000 },
+ { 0x00008340, 0x000107ff },
+ { 0x00008344, 0x00000000 },
+ { 0x00009808, 0x00000000 },
+ { 0x0000980c, 0xaf268e30 },
+ { 0x00009810, 0xfd14e000 },
+ { 0x00009814, 0x9c0a9f6b },
+ { 0x0000981c, 0x00000000 },
+ { 0x0000982c, 0x0000a000 },
+ { 0x00009830, 0x00000000 },
+ { 0x0000983c, 0x00200400 },
+ { 0x00009840, 0x206a01ae },
+ { 0x0000984c, 0x0040233c },
+ { 0x0000a84c, 0x0040233c },
+ { 0x00009854, 0x00000044 },
+ { 0x00009900, 0x00000000 },
+ { 0x00009904, 0x00000000 },
+ { 0x00009908, 0x00000000 },
+ { 0x0000990c, 0x00000000 },
+ { 0x0000991c, 0x10000fff },
+ { 0x00009920, 0x04900000 },
+ { 0x0000a920, 0x04900000 },
+ { 0x00009928, 0x00000001 },
+ { 0x0000992c, 0x00000004 },
+ { 0x00009934, 0x1e1f2022 },
+ { 0x00009938, 0x0a0b0c0d },
+ { 0x0000993c, 0x00000000 },
+ { 0x00009948, 0x9280c00a },
+ { 0x0000994c, 0x00020028 },
+ { 0x00009954, 0xe250a51e },
+ { 0x00009958, 0x3388ffff },
+ { 0x00009940, 0x00781204 },
+ { 0x0000c95c, 0x004b6a8e },
+ { 0x0000c968, 0x000003ce },
+ { 0x00009970, 0x190fb514 },
+ { 0x00009974, 0x00000000 },
+ { 0x00009978, 0x00000001 },
+ { 0x0000997c, 0x00000000 },
+ { 0x00009980, 0x00000000 },
+ { 0x00009984, 0x00000000 },
+ { 0x00009988, 0x00000000 },
+ { 0x0000998c, 0x00000000 },
+ { 0x00009990, 0x00000000 },
+ { 0x00009994, 0x00000000 },
+ { 0x00009998, 0x00000000 },
+ { 0x0000999c, 0x00000000 },
+ { 0x000099a0, 0x00000000 },
+ { 0x000099a4, 0x00000001 },
+ { 0x000099a8, 0x201fff00 },
+ { 0x000099ac, 0x006f00c4 },
+ { 0x000099b0, 0x03051000 },
+ { 0x000099b4, 0x00000820 },
+ { 0x000099dc, 0x00000000 },
+ { 0x000099e0, 0x00000000 },
+ { 0x000099e4, 0xaaaaaaaa },
+ { 0x000099e8, 0x3c466478 },
+ { 0x000099ec, 0x0cc80caa },
+ { 0x000099fc, 0x00001042 },
+ { 0x0000a210, 0x4080a333 },
+ { 0x0000a214, 0x40206c10 },
+ { 0x0000a218, 0x009c4060 },
+ { 0x0000a220, 0x01834061 },
+ { 0x0000a224, 0x00000400 },
+ { 0x0000a228, 0x000003b5 },
+ { 0x0000a22c, 0x23277200 },
+ { 0x0000a234, 0x20202020 },
+ { 0x0000a238, 0x20202020 },
+ { 0x0000a23c, 0x13c889af },
+ { 0x0000a240, 0x38490a20 },
+ { 0x0000a244, 0x00007bb6 },
+ { 0x0000a248, 0x0fff3ffc },
+ { 0x0000a24c, 0x00000001 },
+ { 0x0000a250, 0x001da000 },
+ { 0x0000a254, 0x00000000 },
+ { 0x0000a258, 0x0cdbd380 },
+ { 0x0000a25c, 0x0f0f0f01 },
+ { 0x0000a260, 0xdfa91f01 },
+ { 0x0000a268, 0x00000000 },
+ { 0x0000a26c, 0x0ebae9c6 },
+ { 0x0000b26c, 0x0ebae9c6 },
+ { 0x0000d270, 0x00820820 },
+ { 0x0000a278, 0x1ce739ce },
+ { 0x0000a27c, 0x050701ce },
+ { 0x0000a358, 0x7999aa0f },
+ { 0x0000d35c, 0x07ffffef },
+ { 0x0000d360, 0x0fffffe7 },
+ { 0x0000d364, 0x17ffffe5 },
+ { 0x0000d368, 0x1fffffe4 },
+ { 0x0000d36c, 0x37ffffe3 },
+ { 0x0000d370, 0x3fffffe3 },
+ { 0x0000d374, 0x57ffffe3 },
+ { 0x0000d378, 0x5fffffe2 },
+ { 0x0000d37c, 0x7fffffe2 },
+ { 0x0000d380, 0x7f3c7bba },
+ { 0x0000d384, 0xf3307ff0 },
+ { 0x0000a388, 0x0c000000 },
+ { 0x0000a38c, 0x20202020 },
+ { 0x0000a390, 0x20202020 },
+ { 0x0000a394, 0x1ce739ce },
+ { 0x0000a398, 0x000001ce },
+ { 0x0000a39c, 0x00000001 },
+ { 0x0000a3a0, 0x00000000 },
+ { 0x0000a3a4, 0x00000000 },
+ { 0x0000a3a8, 0x00000000 },
+ { 0x0000a3ac, 0x00000000 },
+ { 0x0000a3b0, 0x00000000 },
+ { 0x0000a3b4, 0x00000000 },
+ { 0x0000a3b8, 0x00000000 },
+ { 0x0000a3bc, 0x00000000 },
+ { 0x0000a3c0, 0x00000000 },
+ { 0x0000a3c4, 0x00000000 },
+ { 0x0000a3c8, 0x00000246 },
+ { 0x0000a3cc, 0x20202020 },
+ { 0x0000a3d0, 0x20202020 },
+ { 0x0000a3d4, 0x20202020 },
+ { 0x0000a3dc, 0x1ce739ce },
+ { 0x0000a3e0, 0x000001ce },
+ { 0x0000a3e4, 0x00000000 },
+ { 0x0000a3e8, 0x18c43433 },
+ { 0x0000a3ec, 0x00f38081 },
+ { 0x00007800, 0x00040000 },
+ { 0x00007804, 0xdb005012 },
+ { 0x00007808, 0x04924914 },
+ { 0x0000780c, 0x21084210 },
+ { 0x00007810, 0x6d801300 },
+ { 0x00007814, 0x0019beff },
+ { 0x00007818, 0x07e40000 },
+ { 0x0000781c, 0x00492000 },
+ { 0x00007820, 0x92492480 },
+ { 0x00007824, 0x00040000 },
+ { 0x00007828, 0xdb005012 },
+ { 0x0000782c, 0x04924914 },
+ { 0x00007830, 0x21084210 },
+ { 0x00007834, 0x6d801300 },
+ { 0x00007838, 0x0019beff },
+ { 0x0000783c, 0x07e40000 },
+ { 0x00007840, 0x00492000 },
+ { 0x00007844, 0x92492480 },
+ { 0x00007848, 0x00120000 },
+ { 0x00007850, 0x54214514 },
+ { 0x00007858, 0x92592692 },
+ { 0x00007860, 0x52802000 },
+ { 0x00007864, 0x0a8e370e },
+ { 0x00007868, 0xc0102850 },
+ { 0x0000786c, 0x812d4000 },
+ { 0x00007874, 0x001b6db0 },
+ { 0x00007878, 0x00376b63 },
+ { 0x0000787c, 0x06db6db6 },
+ { 0x00007880, 0x006d8000 },
+ { 0x00007884, 0xffeffffe },
+ { 0x00007888, 0xffeffffe },
+ { 0x00007890, 0x00060aeb },
+ { 0x00007894, 0x5a108000 },
+ { 0x00007898, 0x2a850160 },
+};
+
+
+
+
+static const u32 ar9280Modes_9280_2[][6] = {
+ { 0x00001030, 0x00000230, 0x00000460, 0x000002c0, 0x00000160, 0x000001e0 },
+ { 0x00001070, 0x00000168, 0x000002d0, 0x00000318, 0x0000018c, 0x000001e0 },
+ { 0x000010b0, 0x00000e60, 0x00001cc0, 0x00007c70, 0x00003e38, 0x00001180 },
+ { 0x000010f0, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000008 },
+ { 0x00008014, 0x03e803e8, 0x07d007d0, 0x10801600, 0x08400b00, 0x06e006e0 },
+ { 0x0000801c, 0x128d8027, 0x128d804f, 0x12e00057, 0x12e0002b, 0x0988004f },
+ { 0x00008318, 0x00003e80, 0x00007d00, 0x00006880, 0x00003440, 0x00006880 },
+ { 0x00009804, 0x00000300, 0x000003c4, 0x000003c4, 0x00000300, 0x00000303 },
+ { 0x00009820, 0x02020200, 0x02020200, 0x02020200, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009828, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001, 0x0a020001 },
+ { 0x00009834, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e, 0x00000e0e },
+ { 0x00009838, 0x00000007, 0x00000007, 0x00000007, 0x00000007, 0x00000007 },
+ { 0x00009840, 0x206a012e, 0x206a012e, 0x206a022e, 0x206a022e, 0x206a022e },
+ { 0x00009844, 0x0372161e, 0x0372161e, 0x037216a0, 0x037216a0, 0x037216a0 },
+ { 0x00009848, 0x00001066, 0x00001066, 0x00001063, 0x00001063, 0x00001063 },
+ { 0x0000a848, 0x00001066, 0x00001066, 0x00001063, 0x00001063, 0x00001063 },
+ { 0x00009850, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2, 0x6d4000e2 },
+ { 0x00009858, 0x7ec84d2e, 0x7ec84d2e, 0x7ec88d2e, 0x7ec88d2e, 0x7ec88d2e },
+ { 0x0000985c, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e, 0x3139605e },
+ { 0x00009860, 0x00048d18, 0x00048d18, 0x00048d20, 0x00048d20, 0x00048d18 },
+ { 0x0000c864, 0x0000fe00, 0x0000fe00, 0x0001ce00, 0x0001ce00, 0x0001ce00 },
+ { 0x00009868, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0, 0x5ac640d0 },
+ { 0x0000986c, 0x06903081, 0x06903081, 0x06903881, 0x06903881, 0x06903881 },
+ { 0x00009914, 0x000007d0, 0x000007d0, 0x00000898, 0x00000898, 0x000007d0 },
+ { 0x00009918, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b, 0x00000016 },
+ { 0x00009924, 0xd00a8a07, 0xd00a8a07, 0xd00a8a0d, 0xd00a8a0d, 0xd00a8a0d },
+ { 0x00009944, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010, 0xdfbc1010 },
+ { 0x00009960, 0x00000010, 0x00000010, 0x00000010, 0x00000010, 0x00000010 },
+ { 0x0000a960, 0x00000010, 0x00000010, 0x00000010, 0x00000010, 0x00000010 },
+ { 0x00009964, 0x00000210, 0x00000210, 0x00000210, 0x00000210, 0x00000210 },
+ { 0x0000c9b8, 0x0000000f, 0x0000000f, 0x0000001c, 0x0000001c, 0x0000001c },
+ { 0x0000c9bc, 0x00000600, 0x00000600, 0x00000c00, 0x00000c00, 0x00000c00 },
+ { 0x000099c0, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4, 0x05eea6d4 },
+ { 0x000099c4, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77, 0x06336f77 },
+ { 0x000099c8, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329, 0x60f65329 },
+ { 0x000099cc, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8, 0x08f186c8 },
+ { 0x000099d0, 0x00046384, 0x00046384, 0x00046384, 0x00046384, 0x00046384 },
+ { 0x000099d4, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x000099d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x00009a00, 0x00008184, 0x00008184, 0x00000290, 0x00000290, 0x00000290 },
+ { 0x00009a04, 0x00008188, 0x00008188, 0x00000300, 0x00000300, 0x00000300 },
+ { 0x00009a08, 0x0000818c, 0x0000818c, 0x00000304, 0x00000304, 0x00000304 },
+ { 0x00009a0c, 0x00008190, 0x00008190, 0x00000308, 0x00000308, 0x00000308 },
+ { 0x00009a10, 0x00008194, 0x00008194, 0x0000030c, 0x0000030c, 0x0000030c },
+ { 0x00009a14, 0x00008200, 0x00008200, 0x00008000, 0x00008000, 0x00008000 },
+ { 0x00009a18, 0x00008204, 0x00008204, 0x00008004, 0x00008004, 0x00008004 },
+ { 0x00009a1c, 0x00008208, 0x00008208, 0x00008008, 0x00008008, 0x00008008 },
+ { 0x00009a20, 0x0000820c, 0x0000820c, 0x0000800c, 0x0000800c, 0x0000800c },
+ { 0x00009a24, 0x00008210, 0x00008210, 0x00008080, 0x00008080, 0x00008080 },
+ { 0x00009a28, 0x00008214, 0x00008214, 0x00008084, 0x00008084, 0x00008084 },
+ { 0x00009a2c, 0x00008280, 0x00008280, 0x00008088, 0x00008088, 0x00008088 },
+ { 0x00009a30, 0x00008284, 0x00008284, 0x0000808c, 0x0000808c, 0x0000808c },
+ { 0x00009a34, 0x00008288, 0x00008288, 0x00008100, 0x00008100, 0x00008100 },
+ { 0x00009a38, 0x0000828c, 0x0000828c, 0x00008104, 0x00008104, 0x00008104 },
+ { 0x00009a3c, 0x00008290, 0x00008290, 0x00008108, 0x00008108, 0x00008108 },
+ { 0x00009a40, 0x00008300, 0x00008300, 0x0000810c, 0x0000810c, 0x0000810c },
+ { 0x00009a44, 0x00008304, 0x00008304, 0x00008110, 0x00008110, 0x00008110 },
+ { 0x00009a48, 0x00008308, 0x00008308, 0x00008114, 0x00008114, 0x00008114 },
+ { 0x00009a4c, 0x0000830c, 0x0000830c, 0x00008180, 0x00008180, 0x00008180 },
+ { 0x00009a50, 0x00008310, 0x00008310, 0x00008184, 0x00008184, 0x00008184 },
+ { 0x00009a54, 0x00008314, 0x00008314, 0x00008188, 0x00008188, 0x00008188 },
+ { 0x00009a58, 0x00008380, 0x00008380, 0x0000818c, 0x0000818c, 0x0000818c },
+ { 0x00009a5c, 0x00008384, 0x00008384, 0x00008190, 0x00008190, 0x00008190 },
+ { 0x00009a60, 0x00008388, 0x00008388, 0x00008194, 0x00008194, 0x00008194 },
+ { 0x00009a64, 0x0000838c, 0x0000838c, 0x000081a0, 0x000081a0, 0x000081a0 },
+ { 0x00009a68, 0x00008390, 0x00008390, 0x0000820c, 0x0000820c, 0x0000820c },
+ { 0x00009a6c, 0x00008394, 0x00008394, 0x000081a8, 0x000081a8, 0x000081a8 },
+ { 0x00009a70, 0x0000a380, 0x0000a380, 0x00008284, 0x00008284, 0x00008284 },
+ { 0x00009a74, 0x0000a384, 0x0000a384, 0x00008288, 0x00008288, 0x00008288 },
+ { 0x00009a78, 0x0000a388, 0x0000a388, 0x00008224, 0x00008224, 0x00008224 },
+ { 0x00009a7c, 0x0000a38c, 0x0000a38c, 0x00008290, 0x00008290, 0x00008290 },
+ { 0x00009a80, 0x0000a390, 0x0000a390, 0x00008300, 0x00008300, 0x00008300 },
+ { 0x00009a84, 0x0000a394, 0x0000a394, 0x00008304, 0x00008304, 0x00008304 },
+ { 0x00009a88, 0x0000a780, 0x0000a780, 0x00008308, 0x00008308, 0x00008308 },
+ { 0x00009a8c, 0x0000a784, 0x0000a784, 0x0000830c, 0x0000830c, 0x0000830c },
+ { 0x00009a90, 0x0000a788, 0x0000a788, 0x00008380, 0x00008380, 0x00008380 },
+ { 0x00009a94, 0x0000a78c, 0x0000a78c, 0x00008384, 0x00008384, 0x00008384 },
+ { 0x00009a98, 0x0000a790, 0x0000a790, 0x00008700, 0x00008700, 0x00008700 },
+ { 0x00009a9c, 0x0000a794, 0x0000a794, 0x00008704, 0x00008704, 0x00008704 },
+ { 0x00009aa0, 0x0000ab84, 0x0000ab84, 0x00008708, 0x00008708, 0x00008708 },
+ { 0x00009aa4, 0x0000ab88, 0x0000ab88, 0x0000870c, 0x0000870c, 0x0000870c },
+ { 0x00009aa8, 0x0000ab8c, 0x0000ab8c, 0x00008780, 0x00008780, 0x00008780 },
+ { 0x00009aac, 0x0000ab90, 0x0000ab90, 0x00008784, 0x00008784, 0x00008784 },
+ { 0x00009ab0, 0x0000ab94, 0x0000ab94, 0x00008b00, 0x00008b00, 0x00008b00 },
+ { 0x00009ab4, 0x0000af80, 0x0000af80, 0x00008b04, 0x00008b04, 0x00008b04 },
+ { 0x00009ab8, 0x0000af84, 0x0000af84, 0x00008b08, 0x00008b08, 0x00008b08 },
+ { 0x00009abc, 0x0000af88, 0x0000af88, 0x00008b0c, 0x00008b0c, 0x00008b0c },
+ { 0x00009ac0, 0x0000af8c, 0x0000af8c, 0x00008b80, 0x00008b80, 0x00008b80 },
+ { 0x00009ac4, 0x0000af90, 0x0000af90, 0x00008b84, 0x00008b84, 0x00008b84 },
+ { 0x00009ac8, 0x0000af94, 0x0000af94, 0x00008b88, 0x00008b88, 0x00008b88 },
+ { 0x00009acc, 0x0000b380, 0x0000b380, 0x00008b8c, 0x00008b8c, 0x00008b8c },
+ { 0x00009ad0, 0x0000b384, 0x0000b384, 0x00008b90, 0x00008b90, 0x00008b90 },
+ { 0x00009ad4, 0x0000b388, 0x0000b388, 0x00008f80, 0x00008f80, 0x00008f80 },
+ { 0x00009ad8, 0x0000b38c, 0x0000b38c, 0x00008f84, 0x00008f84, 0x00008f84 },
+ { 0x00009adc, 0x0000b390, 0x0000b390, 0x00008f88, 0x00008f88, 0x00008f88 },
+ { 0x00009ae0, 0x0000b394, 0x0000b394, 0x00008f8c, 0x00008f8c, 0x00008f8c },
+ { 0x00009ae4, 0x0000b398, 0x0000b398, 0x00008f90, 0x00008f90, 0x00008f90 },
+ { 0x00009ae8, 0x0000b780, 0x0000b780, 0x0000930c, 0x0000930c, 0x0000930c },
+ { 0x00009aec, 0x0000b784, 0x0000b784, 0x00009310, 0x00009310, 0x00009310 },
+ { 0x00009af0, 0x0000b788, 0x0000b788, 0x00009384, 0x00009384, 0x00009384 },
+ { 0x00009af4, 0x0000b78c, 0x0000b78c, 0x00009388, 0x00009388, 0x00009388 },
+ { 0x00009af8, 0x0000b790, 0x0000b790, 0x00009324, 0x00009324, 0x00009324 },
+ { 0x00009afc, 0x0000b794, 0x0000b794, 0x00009704, 0x00009704, 0x00009704 },
+ { 0x00009b00, 0x0000b798, 0x0000b798, 0x000096a4, 0x000096a4, 0x000096a4 },
+ { 0x00009b04, 0x0000d784, 0x0000d784, 0x000096a8, 0x000096a8, 0x000096a8 },
+ { 0x00009b08, 0x0000d788, 0x0000d788, 0x00009710, 0x00009710, 0x00009710 },
+ { 0x00009b0c, 0x0000d78c, 0x0000d78c, 0x00009714, 0x00009714, 0x00009714 },
+ { 0x00009b10, 0x0000d790, 0x0000d790, 0x00009720, 0x00009720, 0x00009720 },
+ { 0x00009b14, 0x0000f780, 0x0000f780, 0x00009724, 0x00009724, 0x00009724 },
+ { 0x00009b18, 0x0000f784, 0x0000f784, 0x00009728, 0x00009728, 0x00009728 },
+ { 0x00009b1c, 0x0000f788, 0x0000f788, 0x0000972c, 0x0000972c, 0x0000972c },
+ { 0x00009b20, 0x0000f78c, 0x0000f78c, 0x000097a0, 0x000097a0, 0x000097a0 },
+ { 0x00009b24, 0x0000f790, 0x0000f790, 0x000097a4, 0x000097a4, 0x000097a4 },
+ { 0x00009b28, 0x0000f794, 0x0000f794, 0x000097a8, 0x000097a8, 0x000097a8 },
+ { 0x00009b2c, 0x0000f7a4, 0x0000f7a4, 0x000097b0, 0x000097b0, 0x000097b0 },
+ { 0x00009b30, 0x0000f7a8, 0x0000f7a8, 0x000097b4, 0x000097b4, 0x000097b4 },
+ { 0x00009b34, 0x0000f7ac, 0x0000f7ac, 0x000097b8, 0x000097b8, 0x000097b8 },
+ { 0x00009b38, 0x0000f7b0, 0x0000f7b0, 0x000097a5, 0x000097a5, 0x000097a5 },
+ { 0x00009b3c, 0x0000f7b4, 0x0000f7b4, 0x000097a9, 0x000097a9, 0x000097a9 },
+ { 0x00009b40, 0x0000f7a1, 0x0000f7a1, 0x000097ad, 0x000097ad, 0x000097ad },
+ { 0x00009b44, 0x0000f7a5, 0x0000f7a5, 0x000097b1, 0x000097b1, 0x000097b1 },
+ { 0x00009b48, 0x0000f7a9, 0x0000f7a9, 0x000097b5, 0x000097b5, 0x000097b5 },
+ { 0x00009b4c, 0x0000f7ad, 0x0000f7ad, 0x000097b9, 0x000097b9, 0x000097b9 },
+ { 0x00009b50, 0x0000f7b1, 0x0000f7b1, 0x000097c5, 0x000097c5, 0x000097c5 },
+ { 0x00009b54, 0x0000f7b5, 0x0000f7b5, 0x000097c9, 0x000097c9, 0x000097c9 },
+ { 0x00009b58, 0x0000f7c5, 0x0000f7c5, 0x000097d1, 0x000097d1, 0x000097d1 },
+ { 0x00009b5c, 0x0000f7c9, 0x0000f7c9, 0x000097d5, 0x000097d5, 0x000097d5 },
+ { 0x00009b60, 0x0000f7cd, 0x0000f7cd, 0x000097d9, 0x000097d9, 0x000097d9 },
+ { 0x00009b64, 0x0000f7d1, 0x0000f7d1, 0x000097c6, 0x000097c6, 0x000097c6 },
+ { 0x00009b68, 0x0000f7d5, 0x0000f7d5, 0x000097ca, 0x000097ca, 0x000097ca },
+ { 0x00009b6c, 0x0000f7c2, 0x0000f7c2, 0x000097ce, 0x000097ce, 0x000097ce },
+ { 0x00009b70, 0x0000f7c6, 0x0000f7c6, 0x000097d2, 0x000097d2, 0x000097d2 },
+ { 0x00009b74, 0x0000f7ca, 0x0000f7ca, 0x000097d6, 0x000097d6, 0x000097d6 },
+ { 0x00009b78, 0x0000f7ce, 0x0000f7ce, 0x000097c3, 0x000097c3, 0x000097c3 },
+ { 0x00009b7c, 0x0000f7d2, 0x0000f7d2, 0x000097c7, 0x000097c7, 0x000097c7 },
+ { 0x00009b80, 0x0000f7d6, 0x0000f7d6, 0x000097cb, 0x000097cb, 0x000097cb },
+ { 0x00009b84, 0x0000f7c3, 0x0000f7c3, 0x000097cf, 0x000097cf, 0x000097cf },
+ { 0x00009b88, 0x0000f7c7, 0x0000f7c7, 0x000097d7, 0x000097d7, 0x000097d7 },
+ { 0x00009b8c, 0x0000f7cb, 0x0000f7cb, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b90, 0x0000f7d3, 0x0000f7d3, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b94, 0x0000f7d7, 0x0000f7d7, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b98, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009b9c, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009ba8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bac, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bb8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bbc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bc8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bcc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bd8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bdc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009be8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bec, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf0, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf4, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bf8, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x00009bfc, 0x0000f7db, 0x0000f7db, 0x000097db, 0x000097db, 0x000097db },
+ { 0x0000a204, 0x00000444, 0x00000444, 0x00000444, 0x00000444, 0x00000444 },
+ { 0x0000a208, 0x803e4788, 0x803e4788, 0x803e4788, 0x803e4788, 0x803e4788 },
+ { 0x0000a20c, 0x00000014, 0x00000014, 0x0001f019, 0x0001f019, 0x0001f019 },
+ { 0x0000b20c, 0x00000014, 0x00000014, 0x0001f019, 0x0001f019, 0x0001f019 },
+ { 0x0000a21c, 0x1463800a, 0x1463800a, 0x1463800a, 0x1463800a, 0x1463800a },
+ { 0x0000a230, 0x00000000, 0x00000000, 0x00000210, 0x00000108, 0x00000000 },
+ { 0x0000a250, 0x001ff000, 0x001ff000, 0x001da000, 0x001da000, 0x001da000 },
+ { 0x0000a274, 0x0a19c652, 0x0a19c652, 0x0a1aa652, 0x0a1aa652, 0x0a1aa652 },
+ { 0x0000a300, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x0000a304, 0x00003002, 0x00003002, 0x00003002, 0x00003002, 0x00003002 },
+ { 0x0000a308, 0x00006004, 0x00006004, 0x00008009, 0x00008009, 0x00008009 },
+ { 0x0000a30c, 0x0000a006, 0x0000a006, 0x0000b00b, 0x0000b00b, 0x0000b00b },
+ { 0x0000a310, 0x0000e012, 0x0000e012, 0x0000e012, 0x0000e012, 0x0000e012 },
+ { 0x0000a314, 0x00011014, 0x00011014, 0x00012048, 0x00012048, 0x00012048 },
+ { 0x0000a318, 0x0001504a, 0x0001504a, 0x0001604a, 0x0001604a, 0x0001604a },
+ { 0x0000a31c, 0x0001904c, 0x0001904c, 0x0001a211, 0x0001a211, 0x0001a211 },
+ { 0x0000a320, 0x0001c04e, 0x0001c04e, 0x0001e213, 0x0001e213, 0x0001e213 },
+ { 0x0000a324, 0x00020092, 0x00020092, 0x0002121b, 0x0002121b, 0x0002121b },
+ { 0x0000a328, 0x0002410a, 0x0002410a, 0x00024412, 0x00024412, 0x00024412 },
+ { 0x0000a32c, 0x0002710c, 0x0002710c, 0x00028414, 0x00028414, 0x00028414 },
+ { 0x0000a330, 0x0002b18b, 0x0002b18b, 0x0002b44a, 0x0002b44a, 0x0002b44a },
+ { 0x0000a334, 0x0002e1cc, 0x0002e1cc, 0x00030649, 0x00030649, 0x00030649 },
+ { 0x0000a338, 0x000321ec, 0x000321ec, 0x0003364b, 0x0003364b, 0x0003364b },
+ { 0x0000a33c, 0x000321ec, 0x000321ec, 0x00038a49, 0x00038a49, 0x00038a49 },
+ { 0x0000a340, 0x000321ec, 0x000321ec, 0x0003be48, 0x0003be48, 0x0003be48 },
+ { 0x0000a344, 0x000321ec, 0x000321ec, 0x0003ee4a, 0x0003ee4a, 0x0003ee4a },
+ { 0x0000a348, 0x000321ec, 0x000321ec, 0x00042e88, 0x00042e88, 0x00042e88 },
+ { 0x0000a34c, 0x000321ec, 0x000321ec, 0x00046e8a, 0x00046e8a, 0x00046e8a },
+ { 0x0000a350, 0x000321ec, 0x000321ec, 0x00049ec9, 0x00049ec9, 0x00049ec9 },
+ { 0x0000a354, 0x000321ec, 0x000321ec, 0x0004bf42, 0x0004bf42, 0x0004bf42 },
+ { 0x0000a358, 0x7999aa02, 0x7999aa02, 0x7999aa0e, 0x7999aa0e, 0x7999aa0e },
+ { 0x0000a3d8, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000 },
+ { 0x00007894, 0x5a508000, 0x5a508000, 0x5a508000, 0x5a508000, 0x5a508000 },
+};
+
+static const u32 ar9280Common_9280_2[][2] = {
+ { 0x0000000c, 0x00000000 },
+ { 0x00000030, 0x00020015 },
+ { 0x00000034, 0x00000005 },
+ { 0x00000040, 0x00000000 },
+ { 0x00000044, 0x00000008 },
+ { 0x00000048, 0x00000008 },
+ { 0x0000004c, 0x00000010 },
+ { 0x00000050, 0x00000000 },
+ { 0x00000054, 0x0000001f },
+ { 0x00000800, 0x00000000 },
+ { 0x00000804, 0x00000000 },
+ { 0x00000808, 0x00000000 },
+ { 0x0000080c, 0x00000000 },
+ { 0x00000810, 0x00000000 },
+ { 0x00000814, 0x00000000 },
+ { 0x00000818, 0x00000000 },
+ { 0x0000081c, 0x00000000 },
+ { 0x00000820, 0x00000000 },
+ { 0x00000824, 0x00000000 },
+ { 0x00001040, 0x002ffc0f },
+ { 0x00001044, 0x002ffc0f },
+ { 0x00001048, 0x002ffc0f },
+ { 0x0000104c, 0x002ffc0f },
+ { 0x00001050, 0x002ffc0f },
+ { 0x00001054, 0x002ffc0f },
+ { 0x00001058, 0x002ffc0f },
+ { 0x0000105c, 0x002ffc0f },
+ { 0x00001060, 0x002ffc0f },
+ { 0x00001064, 0x002ffc0f },
+ { 0x00001230, 0x00000000 },
+ { 0x00001270, 0x00000000 },
+ { 0x00001038, 0x00000000 },
+ { 0x00001078, 0x00000000 },
+ { 0x000010b8, 0x00000000 },
+ { 0x000010f8, 0x00000000 },
+ { 0x00001138, 0x00000000 },
+ { 0x00001178, 0x00000000 },
+ { 0x000011b8, 0x00000000 },
+ { 0x000011f8, 0x00000000 },
+ { 0x00001238, 0x00000000 },
+ { 0x00001278, 0x00000000 },
+ { 0x000012b8, 0x00000000 },
+ { 0x000012f8, 0x00000000 },
+ { 0x00001338, 0x00000000 },
+ { 0x00001378, 0x00000000 },
+ { 0x000013b8, 0x00000000 },
+ { 0x000013f8, 0x00000000 },
+ { 0x00001438, 0x00000000 },
+ { 0x00001478, 0x00000000 },
+ { 0x000014b8, 0x00000000 },
+ { 0x000014f8, 0x00000000 },
+ { 0x00001538, 0x00000000 },
+ { 0x00001578, 0x00000000 },
+ { 0x000015b8, 0x00000000 },
+ { 0x000015f8, 0x00000000 },
+ { 0x00001638, 0x00000000 },
+ { 0x00001678, 0x00000000 },
+ { 0x000016b8, 0x00000000 },
+ { 0x000016f8, 0x00000000 },
+ { 0x00001738, 0x00000000 },
+ { 0x00001778, 0x00000000 },
+ { 0x000017b8, 0x00000000 },
+ { 0x000017f8, 0x00000000 },
+ { 0x0000103c, 0x00000000 },
+ { 0x0000107c, 0x00000000 },
+ { 0x000010bc, 0x00000000 },
+ { 0x000010fc, 0x00000000 },
+ { 0x0000113c, 0x00000000 },
+ { 0x0000117c, 0x00000000 },
+ { 0x000011bc, 0x00000000 },
+ { 0x000011fc, 0x00000000 },
+ { 0x0000123c, 0x00000000 },
+ { 0x0000127c, 0x00000000 },
+ { 0x000012bc, 0x00000000 },
+ { 0x000012fc, 0x00000000 },
+ { 0x0000133c, 0x00000000 },
+ { 0x0000137c, 0x00000000 },
+ { 0x000013bc, 0x00000000 },
+ { 0x000013fc, 0x00000000 },
+ { 0x0000143c, 0x00000000 },
+ { 0x0000147c, 0x00000000 },
+ { 0x00004030, 0x00000002 },
+ { 0x0000403c, 0x00000002 },
+ { 0x00004024, 0x0000001f },
+ { 0x00004060, 0x00000000 },
+ { 0x00004064, 0x00000000 },
+ { 0x00007010, 0x00000033 },
+ { 0x00007034, 0x00000002 },
+ { 0x00007038, 0x000004c2 },
+ { 0x00008004, 0x00000000 },
+ { 0x00008008, 0x00000000 },
+ { 0x0000800c, 0x00000000 },
+ { 0x00008018, 0x00000700 },
+ { 0x00008020, 0x00000000 },
+ { 0x00008038, 0x00000000 },
+ { 0x0000803c, 0x00000000 },
+ { 0x00008048, 0x40000000 },
+ { 0x00008054, 0x00000000 },
+ { 0x00008058, 0x00000000 },
+ { 0x0000805c, 0x000fc78f },
+ { 0x00008060, 0x0000000f },
+ { 0x00008064, 0x00000000 },
+ { 0x00008070, 0x00000000 },
+ { 0x000080c0, 0x2a80001a },
+ { 0x000080c4, 0x05dc01e0 },
+ { 0x000080c8, 0x1f402710 },
+ { 0x000080cc, 0x01f40000 },
+ { 0x000080d0, 0x00001e00 },
+ { 0x000080d4, 0x00000000 },
+ { 0x000080d8, 0x00400000 },
+ { 0x000080e0, 0xffffffff },
+ { 0x000080e4, 0x0000ffff },
+ { 0x000080e8, 0x003f3f3f },
+ { 0x000080ec, 0x00000000 },
+ { 0x000080f0, 0x00000000 },
+ { 0x000080f4, 0x00000000 },
+ { 0x000080f8, 0x00000000 },
+ { 0x000080fc, 0x00020000 },
+ { 0x00008100, 0x00020000 },
+ { 0x00008104, 0x00000001 },
+ { 0x00008108, 0x00000052 },
+ { 0x0000810c, 0x00000000 },
+ { 0x00008110, 0x00000168 },
+ { 0x00008118, 0x000100aa },
+ { 0x0000811c, 0x00003210 },
+ { 0x00008120, 0x08f04800 },
+ { 0x00008124, 0x00000000 },
+ { 0x00008128, 0x00000000 },
+ { 0x0000812c, 0x00000000 },
+ { 0x00008130, 0x00000000 },
+ { 0x00008134, 0x00000000 },
+ { 0x00008138, 0x00000000 },
+ { 0x0000813c, 0x00000000 },
+ { 0x00008144, 0x00000000 },
+ { 0x00008168, 0x00000000 },
+ { 0x0000816c, 0x00000000 },
+ { 0x00008170, 0x32143320 },
+ { 0x00008174, 0xfaa4fa50 },
+ { 0x00008178, 0x00000100 },
+ { 0x0000817c, 0x00000000 },
+ { 0x000081c0, 0x00000000 },
+ { 0x000081d0, 0x00003210 },
+ { 0x000081ec, 0x00000000 },
+ { 0x000081f0, 0x00000000 },
+ { 0x000081f4, 0x00000000 },
+ { 0x000081f8, 0x00000000 },
+ { 0x000081fc, 0x00000000 },
+ { 0x00008200, 0x00000000 },
+ { 0x00008204, 0x00000000 },
+ { 0x00008208, 0x00000000 },
+ { 0x0000820c, 0x00000000 },
+ { 0x00008210, 0x00000000 },
+ { 0x00008214, 0x00000000 },
+ { 0x00008218, 0x00000000 },
+ { 0x0000821c, 0x00000000 },
+ { 0x00008220, 0x00000000 },
+ { 0x00008224, 0x00000000 },
+ { 0x00008228, 0x00000000 },
+ { 0x0000822c, 0x00000000 },
+ { 0x00008230, 0x00000000 },
+ { 0x00008234, 0x00000000 },
+ { 0x00008238, 0x00000000 },
+ { 0x0000823c, 0x00000000 },
+ { 0x00008240, 0x00100000 },
+ { 0x00008244, 0x0010f400 },
+ { 0x00008248, 0x00000100 },
+ { 0x0000824c, 0x0001e800 },
+ { 0x00008250, 0x00000000 },
+ { 0x00008254, 0x00000000 },
+ { 0x00008258, 0x00000000 },
+ { 0x0000825c, 0x400000ff },
+ { 0x00008260, 0x00080922 },
+ { 0x00008270, 0x00000000 },
+ { 0x00008274, 0x40000000 },
+ { 0x00008278, 0x003e4180 },
+ { 0x0000827c, 0x00000000 },
+ { 0x00008284, 0x0000002c },
+ { 0x00008288, 0x0000002c },
+ { 0x0000828c, 0x00000000 },
+ { 0x00008294, 0x00000000 },
+ { 0x00008298, 0x00000000 },
+ { 0x0000829c, 0x00000000 },
+ { 0x00008300, 0x00000040 },
+ { 0x00008314, 0x00000000 },
+ { 0x00008328, 0x00000000 },
+ { 0x0000832c, 0x00000007 },
+ { 0x00008330, 0x00000302 },
+ { 0x00008334, 0x00000e00 },
+ { 0x00008338, 0x00000000 },
+ { 0x0000833c, 0x00000000 },
+ { 0x00008340, 0x000107ff },
+ { 0x00008344, 0x00581043 },
+ { 0x00009808, 0x00000000 },
+ { 0x0000980c, 0xafa68e30 },
+ { 0x00009810, 0xfd14e000 },
+ { 0x00009814, 0x9c0a9f6b },
+ { 0x0000981c, 0x00000000 },
+ { 0x0000982c, 0x0000a000 },
+ { 0x00009830, 0x00000000 },
+ { 0x0000983c, 0x00200400 },
+ { 0x0000984c, 0x0040233c },
+ { 0x0000a84c, 0x0040233c },
+ { 0x00009854, 0x00000044 },
+ { 0x00009900, 0x00000000 },
+ { 0x00009904, 0x00000000 },
+ { 0x00009908, 0x00000000 },
+ { 0x0000990c, 0x00000000 },
+ { 0x00009910, 0x01002310 },
+ { 0x0000991c, 0x10000fff },
+ { 0x00009920, 0x04900000 },
+ { 0x0000a920, 0x04900000 },
+ { 0x00009928, 0x00000001 },
+ { 0x0000992c, 0x00000004 },
+ { 0x00009934, 0x1e1f2022 },
+ { 0x00009938, 0x0a0b0c0d },
+ { 0x0000993c, 0x00000000 },
+ { 0x00009948, 0x9280c00a },
+ { 0x0000994c, 0x00020028 },
+ { 0x00009954, 0x5f3ca3de },
+ { 0x00009958, 0x2108ecff },
+ { 0x00009940, 0x14750604 },
+ { 0x0000c95c, 0x004b6a8e },
+ { 0x0000c968, 0x000003ce },
+ { 0x00009970, 0x190fb515 },
+ { 0x00009974, 0x00000000 },
+ { 0x00009978, 0x00000001 },
+ { 0x0000997c, 0x00000000 },
+ { 0x00009980, 0x00000000 },
+ { 0x00009984, 0x00000000 },
+ { 0x00009988, 0x00000000 },
+ { 0x0000998c, 0x00000000 },
+ { 0x00009990, 0x00000000 },
+ { 0x00009994, 0x00000000 },
+ { 0x00009998, 0x00000000 },
+ { 0x0000999c, 0x00000000 },
+ { 0x000099a0, 0x00000000 },
+ { 0x000099a4, 0x00000001 },
+ { 0x000099a8, 0x201fff00 },
+ { 0x000099ac, 0x006f0000 },
+ { 0x000099b0, 0x03051000 },
+ { 0x000099b4, 0x00000820 },
+ { 0x000099dc, 0x00000000 },
+ { 0x000099e0, 0x00000000 },
+ { 0x000099e4, 0xaaaaaaaa },
+ { 0x000099e8, 0x3c466478 },
+ { 0x000099ec, 0x0cc80caa },
+ { 0x000099f0, 0x00000000 },
+ { 0x000099fc, 0x00001042 },
+ { 0x0000a210, 0x4080a333 },
+ { 0x0000a214, 0x40206c10 },
+ { 0x0000a218, 0x009c4060 },
+ { 0x0000a220, 0x01834061 },
+ { 0x0000a224, 0x00000400 },
+ { 0x0000a228, 0x000003b5 },
+ { 0x0000a22c, 0x233f71c0 },
+ { 0x0000a234, 0x20202020 },
+ { 0x0000a238, 0x20202020 },
+ { 0x0000a23c, 0x13c88000 },
+ { 0x0000a240, 0x38490a20 },
+ { 0x0000a244, 0x00007bb6 },
+ { 0x0000a248, 0x0fff3ffc },
+ { 0x0000a24c, 0x00000000 },
+ { 0x0000a254, 0x00000000 },
+ { 0x0000a258, 0x0cdbd380 },
+ { 0x0000a25c, 0x0f0f0f01 },
+ { 0x0000a260, 0xdfa91f01 },
+ { 0x0000a268, 0x00000000 },
+ { 0x0000a26c, 0x0ebae9c6 },
+ { 0x0000b26c, 0x0ebae9c6 },
+ { 0x0000d270, 0x00820820 },
+ { 0x0000a278, 0x1ce739ce },
+ { 0x0000a27c, 0x050701ce },
+ { 0x0000d35c, 0x07ffffef },
+ { 0x0000d360, 0x0fffffe7 },
+ { 0x0000d364, 0x17ffffe5 },
+ { 0x0000d368, 0x1fffffe4 },
+ { 0x0000d36c, 0x37ffffe3 },
+ { 0x0000d370, 0x3fffffe3 },
+ { 0x0000d374, 0x57ffffe3 },
+ { 0x0000d378, 0x5fffffe2 },
+ { 0x0000d37c, 0x7fffffe2 },
+ { 0x0000d380, 0x7f3c7bba },
+ { 0x0000d384, 0xf3307ff0 },
+ { 0x0000a388, 0x0c000000 },
+ { 0x0000a38c, 0x20202020 },
+ { 0x0000a390, 0x20202020 },
+ { 0x0000a394, 0x1ce739ce },
+ { 0x0000a398, 0x000001ce },
+ { 0x0000a39c, 0x00000001 },
+ { 0x0000a3a0, 0x00000000 },
+ { 0x0000a3a4, 0x00000000 },
+ { 0x0000a3a8, 0x00000000 },
+ { 0x0000a3ac, 0x00000000 },
+ { 0x0000a3b0, 0x00000000 },
+ { 0x0000a3b4, 0x00000000 },
+ { 0x0000a3b8, 0x00000000 },
+ { 0x0000a3bc, 0x00000000 },
+ { 0x0000a3c0, 0x00000000 },
+ { 0x0000a3c4, 0x00000000 },
+ { 0x0000a3c8, 0x00000246 },
+ { 0x0000a3cc, 0x20202020 },
+ { 0x0000a3d0, 0x20202020 },
+ { 0x0000a3d4, 0x20202020 },
+ { 0x0000a3dc, 0x1ce739ce },
+ { 0x0000a3e0, 0x000001ce },
+ { 0x0000a3e4, 0x00000000 },
+ { 0x0000a3e8, 0x18c43433 },
+ { 0x0000a3ec, 0x00f70081 },
+ { 0x00007800, 0x00040000 },
+ { 0x00007804, 0xdb005012 },
+ { 0x00007808, 0x04924914 },
+ { 0x0000780c, 0x21084210 },
+ { 0x00007810, 0x6d801300 },
+ { 0x00007814, 0x0019beff },
+ { 0x00007818, 0x07e41000 },
+ { 0x0000781c, 0x00392000 },
+ { 0x00007820, 0x92592480 },
+ { 0x00007824, 0x00040000 },
+ { 0x00007828, 0xdb005012 },
+ { 0x0000782c, 0x04924914 },
+ { 0x00007830, 0x21084210 },
+ { 0x00007834, 0x6d801300 },
+ { 0x00007838, 0x0019beff },
+ { 0x0000783c, 0x07e40000 },
+ { 0x00007840, 0x00392000 },
+ { 0x00007844, 0x92592480 },
+ { 0x00007848, 0x00100000 },
+ { 0x0000784c, 0x773f0567 },
+ { 0x00007850, 0x54214514 },
+ { 0x00007854, 0x12035828 },
+ { 0x00007858, 0x9259269a },
+ { 0x00007860, 0x52802000 },
+ { 0x00007864, 0x0a8e370e },
+ { 0x00007868, 0xc0102850 },
+ { 0x0000786c, 0x812d4000 },
+ { 0x00007870, 0x807ec400 },
+ { 0x00007874, 0x001b6db0 },
+ { 0x00007878, 0x00376b63 },
+ { 0x0000787c, 0x06db6db6 },
+ { 0x00007880, 0x006d8000 },
+ { 0x00007884, 0xffeffffe },
+ { 0x00007888, 0xffeffffe },
+ { 0x0000788c, 0x00010000 },
+ { 0x00007890, 0x02060aeb },
+ { 0x00007898, 0x2a850160 },
+};
+
+static const u32 ar9280Modes_fast_clock_9280_2[][3] = {
+ { 0x00001030, 0x00000268, 0x000004d0 },
+ { 0x00001070, 0x0000018c, 0x00000318 },
+ { 0x000010b0, 0x00000fd0, 0x00001fa0 },
+ { 0x00008014, 0x044c044c, 0x08980898 },
+ { 0x0000801c, 0x148ec02b, 0x148ec057 },
+ { 0x00008318, 0x000044c0, 0x00008980 },
+ { 0x00009820, 0x02020200, 0x02020200 },
+ { 0x00009824, 0x00000f0f, 0x00000f0f },
+ { 0x00009828, 0x0b020001, 0x0b020001 },
+ { 0x00009834, 0x00000f0f, 0x00000f0f },
+ { 0x00009844, 0x03721821, 0x03721821 },
+ { 0x00009914, 0x00000898, 0x00000898 },
+ { 0x00009918, 0x0000000b, 0x00000016 },
+ { 0x00009944, 0xdfbc1210, 0xdfbc1210 },
+};
+
+
+
+static const u32 ar9280PciePhy_clkreq_off_L1_9280[][2] = {
+ {0x00004040, 0x9248fd00 },
+ {0x00004040, 0x24924924 },
+ {0x00004040, 0xa8000019 },
+ {0x00004040, 0x13160820 },
+ {0x00004040, 0xe5980560 },
+ {0x00004040, 0x401dcffc },
+ {0x00004040, 0x1aaabe40 },
+ {0x00004040, 0xbe105554 },
+ {0x00004040, 0x00043007 },
+ {0x00004044, 0x00000000 },
+};
+
+
+
+static const u32 ar9280PciePhy_clkreq_always_on_L1_9280[][2] = {
+ {0x00004040, 0x9248fd00 },
+ {0x00004040, 0x24924924 },
+ {0x00004040, 0xa8000019 },
+ {0x00004040, 0x13160820 },
+ {0x00004040, 0xe5980560 },
+ {0x00004040, 0x401dcffd },
+ {0x00004040, 0x1aaabe40 },
+ {0x00004040, 0xbe105554 },
+ {0x00004040, 0x00043007 },
+ {0x00004044, 0x00000000 },
+};
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/* mac80211 and PCI callbacks */
+
+#include <linux/nl80211.h>
+#include "core.h"
+
+#define ATH_PCI_VERSION "0.1"
+
+#define IEEE80211_HTCAP_MAXRXAMPDU_FACTOR 13
+#define IEEE80211_ACTION_CAT_HT 7
+#define IEEE80211_ACTION_HT_TXCHWIDTH 0
+
+static char *dev_info = "ath9k";
+
+MODULE_AUTHOR("Atheros Communications");
+MODULE_DESCRIPTION("Support for Atheros 802.11n wireless LAN cards.");
+MODULE_SUPPORTED_DEVICE("Atheros 802.11n WLAN cards");
+MODULE_LICENSE("Dual BSD/GPL");
+
+static struct pci_device_id ath_pci_id_table[] __devinitdata = {
+ { PCI_VDEVICE(ATHEROS, 0x0023) }, /* PCI */
+ { PCI_VDEVICE(ATHEROS, 0x0024) }, /* PCI-E */
+ { PCI_VDEVICE(ATHEROS, 0x0027) }, /* PCI */
+ { PCI_VDEVICE(ATHEROS, 0x0029) }, /* PCI */
+ { PCI_VDEVICE(ATHEROS, 0x002A) }, /* PCI-E */
+ { 0 }
+};
+
+static int ath_get_channel(struct ath_softc *sc,
+ struct ieee80211_channel *chan)
+{
+ int i;
+
+ for (i = 0; i < sc->sc_ah->ah_nchan; i++) {
+ if (sc->sc_ah->ah_channels[i].channel == chan->center_freq)
+ return i;
+ }
+
+ return -1;
+}
+
+static u32 ath_get_extchanmode(struct ath_softc *sc,
+ struct ieee80211_channel *chan)
+{
+ u32 chanmode = 0;
+ u8 ext_chan_offset = sc->sc_ht_info.ext_chan_offset;
+ enum ath9k_ht_macmode tx_chan_width = sc->sc_ht_info.tx_chan_width;
+
+ switch (chan->band) {
+ case IEEE80211_BAND_2GHZ:
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_NONE) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_20))
+ chanmode = CHANNEL_G_HT20;
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_ABOVE) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_2040))
+ chanmode = CHANNEL_G_HT40PLUS;
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_BELOW) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_2040))
+ chanmode = CHANNEL_G_HT40MINUS;
+ break;
+ case IEEE80211_BAND_5GHZ:
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_NONE) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_20))
+ chanmode = CHANNEL_A_HT20;
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_ABOVE) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_2040))
+ chanmode = CHANNEL_A_HT40PLUS;
+ if ((ext_chan_offset == IEEE80211_HT_IE_CHA_SEC_BELOW) &&
+ (tx_chan_width == ATH9K_HT_MACMODE_2040))
+ chanmode = CHANNEL_A_HT40MINUS;
+ break;
+ default:
+ break;
+ }
+
+ return chanmode;
+}
+
+
+static int ath_setkey_tkip(struct ath_softc *sc,
+ struct ieee80211_key_conf *key,
+ struct ath9k_keyval *hk,
+ const u8 *addr)
+{
+ u8 *key_rxmic = NULL;
+ u8 *key_txmic = NULL;
+
+ key_txmic = key->key + NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY;
+ key_rxmic = key->key + NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY;
+
+ if (addr == NULL) {
+ /* Group key installation */
+ memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic));
+ return ath_keyset(sc, key->keyidx, hk, addr);
+ }
+ if (!sc->sc_splitmic) {
+ /*
+ * data key goes at first index,
+ * the hal handles the MIC keys at index+64.
+ */
+ memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic));
+ memcpy(hk->kv_txmic, key_txmic, sizeof(hk->kv_txmic));
+ return ath_keyset(sc, key->keyidx, hk, addr);
+ }
+ /*
+ * TX key goes at first index, RX key at +32.
+ * The hal handles the MIC keys at index+64.
+ */
+ memcpy(hk->kv_mic, key_txmic, sizeof(hk->kv_mic));
+ if (!ath_keyset(sc, key->keyidx, hk, NULL)) {
+ /* Txmic entry failed. No need to proceed further */
+ DPRINTF(sc, ATH_DBG_KEYCACHE,
+ "%s Setting TX MIC Key Failed\n", __func__);
+ return 0;
+ }
+
+ memcpy(hk->kv_mic, key_rxmic, sizeof(hk->kv_mic));
+ /* XXX delete tx key on failure? */
+ return ath_keyset(sc, key->keyidx+32, hk, addr);
+}
+
+static int ath_key_config(struct ath_softc *sc,
+ const u8 *addr,
+ struct ieee80211_key_conf *key)
+{
+ struct ieee80211_vif *vif;
+ struct ath9k_keyval hk;
+ const u8 *mac = NULL;
+ int ret = 0;
+ enum ieee80211_if_types opmode;
+
+ memset(&hk, 0, sizeof(hk));
+
+ switch (key->alg) {
+ case ALG_WEP:
+ hk.kv_type = ATH9K_CIPHER_WEP;
+ break;
+ case ALG_TKIP:
+ hk.kv_type = ATH9K_CIPHER_TKIP;
+ break;
+ case ALG_CCMP:
+ hk.kv_type = ATH9K_CIPHER_AES_CCM;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ hk.kv_len = key->keylen;
+ memcpy(hk.kv_val, key->key, key->keylen);
+
+ if (!sc->sc_vaps[0])
+ return -EIO;
+
+ vif = sc->sc_vaps[0]->av_if_data;
+ opmode = vif->type;
+
+ /*
+ * Strategy:
+ * For _M_STA mc tx, we will not setup a key at all since we never
+ * tx mc.
+ * _M_STA mc rx, we will use the keyID.
+ * for _M_IBSS mc tx, we will use the keyID, and no macaddr.
+ * for _M_IBSS mc rx, we will alloc a slot and plumb the mac of the
+ * peer node. BUT we will plumb a cleartext key so that we can do
+ * perSta default key table lookup in software.
+ */
+ if (is_broadcast_ether_addr(addr)) {
+ switch (opmode) {
+ case IEEE80211_IF_TYPE_STA:
+ /* default key: could be group WPA key
+ * or could be static WEP key */
+ mac = NULL;
+ break;
+ case IEEE80211_IF_TYPE_IBSS:
+ break;
+ case IEEE80211_IF_TYPE_AP:
+ break;
+ default:
+ ASSERT(0);
+ break;
+ }
+ } else {
+ mac = addr;
+ }
+
+ if (key->alg == ALG_TKIP)
+ ret = ath_setkey_tkip(sc, key, &hk, mac);
+ else
+ ret = ath_keyset(sc, key->keyidx, &hk, mac);
+
+ if (!ret)
+ return -EIO;
+
+ sc->sc_keytype = hk.kv_type;
+ return 0;
+}
+
+static void ath_key_delete(struct ath_softc *sc, struct ieee80211_key_conf *key)
+{
+#define ATH_MAX_NUM_KEYS 4
+ int freeslot;
+
+ freeslot = (key->keyidx >= ATH_MAX_NUM_KEYS) ? 1 : 0;
+ ath_key_reset(sc, key->keyidx, freeslot);
+#undef ATH_MAX_NUM_KEYS
+}
+
+static void setup_ht_cap(struct ieee80211_ht_info *ht_info)
+{
+/* Until mac80211 includes these fields */
+
+#define IEEE80211_HT_CAP_DSSSCCK40 0x1000
+#define IEEE80211_HT_CAP_MAXRXAMPDU_65536 0x3 /* 2 ^ 16 */
+#define IEEE80211_HT_CAP_MPDUDENSITY_8 0x6 /* 8 usec */
+
+ ht_info->ht_supported = 1;
+ ht_info->cap = (u16)IEEE80211_HT_CAP_SUP_WIDTH
+ |(u16)IEEE80211_HT_CAP_MIMO_PS
+ |(u16)IEEE80211_HT_CAP_SGI_40
+ |(u16)IEEE80211_HT_CAP_DSSSCCK40;
+
+ ht_info->ampdu_factor = IEEE80211_HT_CAP_MAXRXAMPDU_65536;
+ ht_info->ampdu_density = IEEE80211_HT_CAP_MPDUDENSITY_8;
+ /* setup supported mcs set */
+ memset(ht_info->supp_mcs_set, 0, 16);
+ ht_info->supp_mcs_set[0] = 0xff;
+ ht_info->supp_mcs_set[1] = 0xff;
+ ht_info->supp_mcs_set[12] = IEEE80211_HT_CAP_MCS_TX_DEFINED;
+}
+
+static int ath_rate2idx(struct ath_softc *sc, int rate)
+{
+ int i = 0, cur_band, n_rates;
+ struct ieee80211_hw *hw = sc->hw;
+
+ cur_band = hw->conf.channel->band;
+ n_rates = sc->sbands[cur_band].n_bitrates;
+
+ for (i = 0; i < n_rates; i++) {
+ if (sc->sbands[cur_band].bitrates[i].bitrate == rate)
+ break;
+ }
+
+ /*
+ * NB:mac80211 validates rx rate index against the supported legacy rate
+ * index only (should be done against ht rates also), return the highest
+ * legacy rate index for rx rate which does not match any one of the
+ * supported basic and extended rates to make mac80211 happy.
+ * The following hack will be cleaned up once the issue with
+ * the rx rate index validation in mac80211 is fixed.
+ */
+ if (i == n_rates)
+ return n_rates - 1;
+ return i;
+}
+
+static void ath9k_rx_prepare(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_recv_status *status,
+ struct ieee80211_rx_status *rx_status)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_channel *curchan = hw->conf.channel;
+
+ memset(rx_status, 0, sizeof(struct ieee80211_rx_status));
+
+ rx_status->mactime = status->tsf;
+ rx_status->band = curchan->band;
+ rx_status->freq = curchan->center_freq;
+ rx_status->noise = ATH_DEFAULT_NOISE_FLOOR;
+ rx_status->signal = rx_status->noise + status->rssi;
+ rx_status->rate_idx = ath_rate2idx(sc, (status->rateKbps / 100));
+ rx_status->antenna = status->antenna;
+ rx_status->qual = status->rssi * 100 / 64;
+
+ if (status->flags & ATH_RX_MIC_ERROR)
+ rx_status->flag |= RX_FLAG_MMIC_ERROR;
+ if (status->flags & ATH_RX_FCS_ERROR)
+ rx_status->flag |= RX_FLAG_FAILED_FCS_CRC;
+
+ rx_status->flag |= RX_FLAG_TSFT;
+}
+
+static u8 parse_mpdudensity(u8 mpdudensity)
+{
+ /*
+ * 802.11n D2.0 defined values for "Minimum MPDU Start Spacing":
+ * 0 for no restriction
+ * 1 for 1/4 us
+ * 2 for 1/2 us
+ * 3 for 1 us
+ * 4 for 2 us
+ * 5 for 4 us
+ * 6 for 8 us
+ * 7 for 16 us
+ */
+ switch (mpdudensity) {
+ case 0:
+ return 0;
+ case 1:
+ case 2:
+ case 3:
+ /* Our lower layer calculations limit our precision to
+ 1 microsecond */
+ return 1;
+ case 4:
+ return 2;
+ case 5:
+ return 4;
+ case 6:
+ return 8;
+ case 7:
+ return 16;
+ default:
+ return 0;
+ }
+}
+
+static int ath9k_start(struct ieee80211_hw *hw)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ieee80211_channel *curchan = hw->conf.channel;
+ int error = 0, pos;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Starting driver with "
+ "initial channel: %d MHz\n", __func__, curchan->center_freq);
+
+ /* setup initial channel */
+
+ pos = ath_get_channel(sc, curchan);
+ if (pos == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid channel\n", __func__);
+ return -EINVAL;
+ }
+
+ sc->sc_ah->ah_channels[pos].chanmode =
+ (curchan->band == IEEE80211_BAND_2GHZ) ? CHANNEL_G : CHANNEL_A;
+
+ /* open ath_dev */
+ error = ath_open(sc, &sc->sc_ah->ah_channels[pos]);
+ if (error) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to complete ath_open\n", __func__);
+ return error;
+ }
+
+ ieee80211_wake_queues(hw);
+ return 0;
+}
+
+static int ath9k_tx(struct ieee80211_hw *hw,
+ struct sk_buff *skb)
+{
+ struct ath_softc *sc = hw->priv;
+ int hdrlen, padsize;
+
+ /* Add the padding after the header if this is not already done */
+ hdrlen = ieee80211_get_hdrlen_from_skb(skb);
+ if (hdrlen & 3) {
+ padsize = hdrlen % 4;
+ if (skb_headroom(skb) < padsize)
+ return -1;
+ skb_push(skb, padsize);
+ memmove(skb->data, skb->data + padsize, hdrlen);
+ }
+
+ DPRINTF(sc, ATH_DBG_XMIT, "%s: transmitting packet, skb: %p\n",
+ __func__,
+ skb);
+
+ if (ath_tx_start(sc, skb) != 0) {
+ DPRINTF(sc, ATH_DBG_XMIT, "%s: TX failed\n", __func__);
+ dev_kfree_skb_any(skb);
+ /* FIXME: Check for proper return value from ATH_DEV */
+ return 0;
+ }
+
+ return 0;
+}
+
+static void ath9k_stop(struct ieee80211_hw *hw)
+{
+ struct ath_softc *sc = hw->priv;
+ int error;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Driver halt\n", __func__);
+
+ error = ath_suspend(sc);
+ if (error)
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Device is no longer present\n", __func__);
+
+ ieee80211_stop_queues(hw);
+}
+
+static int ath9k_add_interface(struct ieee80211_hw *hw,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct ath_softc *sc = hw->priv;
+ int error, ic_opmode = 0;
+
+ /* Support only vap for now */
+
+ if (sc->sc_nvaps)
+ return -ENOBUFS;
+
+ switch (conf->type) {
+ case IEEE80211_IF_TYPE_STA:
+ ic_opmode = ATH9K_M_STA;
+ break;
+ case IEEE80211_IF_TYPE_IBSS:
+ ic_opmode = ATH9K_M_IBSS;
+ break;
+ default:
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Only STA and IBSS are supported currently\n",
+ __func__);
+ return -EOPNOTSUPP;
+ }
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Attach a VAP of type: %d\n",
+ __func__,
+ ic_opmode);
+
+ error = ath_vap_attach(sc, 0, conf->vif, ic_opmode);
+ if (error) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to attach vap, error: %d\n",
+ __func__, error);
+ return error;
+ }
+
+ return 0;
+}
+
+static void ath9k_remove_interface(struct ieee80211_hw *hw,
+ struct ieee80211_if_init_conf *conf)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath_vap *avp;
+ int error;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Detach VAP\n", __func__);
+
+ avp = sc->sc_vaps[0];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid interface\n",
+ __func__);
+ return;
+ }
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ ath_slow_ant_div_stop(&sc->sc_antdiv);
+#endif
+
+ /* Update ratectrl */
+ ath_rate_newstate(sc, avp);
+
+ /* Reclaim beacon resources */
+ if (sc->sc_opmode == ATH9K_M_HOSTAP || sc->sc_opmode == ATH9K_M_IBSS) {
+ ath9k_hw_stoptxdma(sc->sc_ah, sc->sc_bhalq);
+ ath_beacon_return(sc, avp);
+ }
+
+ /* Set interrupt mask */
+ sc->sc_imask &= ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS);
+ ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask & ~ATH9K_INT_GLOBAL);
+ sc->sc_beacons = 0;
+
+ error = ath_vap_detach(sc, 0);
+ if (error)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to detach vap, error: %d\n",
+ __func__, error);
+}
+
+static int ath9k_config(struct ieee80211_hw *hw,
+ struct ieee80211_conf *conf)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ieee80211_channel *curchan = hw->conf.channel;
+ int pos;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Set channel: %d MHz\n",
+ __func__,
+ curchan->center_freq);
+
+ pos = ath_get_channel(sc, curchan);
+ if (pos == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid channel\n", __func__);
+ return -EINVAL;
+ }
+
+ sc->sc_ah->ah_channels[pos].chanmode =
+ (curchan->band == IEEE80211_BAND_2GHZ) ?
+ CHANNEL_G : CHANNEL_A;
+
+ if (sc->sc_curaid && hw->conf.ht_conf.ht_supported)
+ sc->sc_ah->ah_channels[pos].chanmode =
+ ath_get_extchanmode(sc, curchan);
+
+ sc->sc_config.txpowlimit = 2 * conf->power_level;
+
+ /* set h/w channel */
+ if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0)
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Unable to set channel\n",
+ __func__);
+
+ return 0;
+}
+
+static int ath9k_config_interface(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_if_conf *conf)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath_vap *avp;
+ u32 rfilt = 0;
+ int error, i;
+ DECLARE_MAC_BUF(mac);
+
+ avp = sc->sc_vaps[0];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid interface\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ if ((conf->changed & IEEE80211_IFCC_BSSID) &&
+ !is_zero_ether_addr(conf->bssid)) {
+ switch (vif->type) {
+ case IEEE80211_IF_TYPE_STA:
+ case IEEE80211_IF_TYPE_IBSS:
+ /* Update ratectrl about the new state */
+ ath_rate_newstate(sc, avp);
+
+ /* Set rx filter */
+ rfilt = ath_calcrxfilter(sc);
+ ath9k_hw_setrxfilter(sc->sc_ah, rfilt);
+
+ /* Set BSSID */
+ memcpy(sc->sc_curbssid, conf->bssid, ETH_ALEN);
+ sc->sc_curaid = 0;
+ ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid,
+ sc->sc_curaid);
+
+ /* Set aggregation protection mode parameters */
+ sc->sc_config.ath_aggr_prot = 0;
+
+ /*
+ * Reset our TSF so that its value is lower than the
+ * beacon that we are trying to catch.
+ * Only then hw will update its TSF register with the
+ * new beacon. Reset the TSF before setting the BSSID
+ * to avoid allowing in any frames that would update
+ * our TSF only to have us clear it
+ * immediately thereafter.
+ */
+ ath9k_hw_reset_tsf(sc->sc_ah);
+
+ /* Disable BMISS interrupt when we're not associated */
+ ath9k_hw_set_interrupts(sc->sc_ah,
+ sc->sc_imask &
+ ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS));
+ sc->sc_imask &= ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS);
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: RX filter 0x%x bssid %s aid 0x%x\n",
+ __func__, rfilt,
+ print_mac(mac, sc->sc_curbssid), sc->sc_curaid);
+
+ /* need to reconfigure the beacon */
+ sc->sc_beacons = 0;
+
+ break;
+ default:
+ break;
+ }
+ }
+
+ if ((conf->changed & IEEE80211_IFCC_BEACON) &&
+ (vif->type == IEEE80211_IF_TYPE_IBSS)) {
+ /*
+ * Allocate and setup the beacon frame.
+ *
+ * Stop any previous beacon DMA. This may be
+ * necessary, for example, when an ibss merge
+ * causes reconfiguration; we may be called
+ * with beacon transmission active.
+ */
+ ath9k_hw_stoptxdma(sc->sc_ah, sc->sc_bhalq);
+
+ error = ath_beacon_alloc(sc, 0);
+ if (error != 0)
+ return error;
+
+ ath_beacon_sync(sc, 0);
+ }
+
+ /* Check for WLAN_CAPABILITY_PRIVACY ? */
+ if ((avp->av_opmode != IEEE80211_IF_TYPE_STA)) {
+ for (i = 0; i < IEEE80211_WEP_NKID; i++)
+ if (ath9k_hw_keyisvalid(sc->sc_ah, (u16)i))
+ ath9k_hw_keysetmac(sc->sc_ah,
+ (u16)i,
+ sc->sc_curbssid);
+ }
+
+ /* Only legacy IBSS for now */
+ if (vif->type == IEEE80211_IF_TYPE_IBSS)
+ ath_update_chainmask(sc, 0);
+
+ return 0;
+}
+
+#define SUPPORTED_FILTERS \
+ (FIF_PROMISC_IN_BSS | \
+ FIF_ALLMULTI | \
+ FIF_CONTROL | \
+ FIF_OTHER_BSS | \
+ FIF_BCN_PRBRESP_PROMISC | \
+ FIF_FCSFAIL)
+
+/* Accept unicast, bcast and mcast frames */
+
+static void ath9k_configure_filter(struct ieee80211_hw *hw,
+ unsigned int changed_flags,
+ unsigned int *total_flags,
+ int mc_count,
+ struct dev_mc_list *mclist)
+{
+ struct ath_softc *sc = hw->priv;
+
+ changed_flags &= SUPPORTED_FILTERS;
+ *total_flags &= SUPPORTED_FILTERS;
+
+ if (changed_flags & FIF_BCN_PRBRESP_PROMISC) {
+ if (*total_flags & FIF_BCN_PRBRESP_PROMISC)
+ ath_scan_start(sc);
+ else
+ ath_scan_end(sc);
+ }
+}
+
+static void ath9k_sta_notify(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ enum sta_notify_cmd cmd,
+ const u8 *addr)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath_node *an;
+ unsigned long flags;
+ DECLARE_MAC_BUF(mac);
+
+ spin_lock_irqsave(&sc->node_lock, flags);
+ an = ath_node_find(sc, (u8 *) addr);
+ spin_unlock_irqrestore(&sc->node_lock, flags);
+
+ switch (cmd) {
+ case STA_NOTIFY_ADD:
+ spin_lock_irqsave(&sc->node_lock, flags);
+ if (!an) {
+ ath_node_attach(sc, (u8 *)addr, 0);
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Attach a node: %s\n",
+ __func__,
+ print_mac(mac, addr));
+ } else {
+ ath_node_get(sc, (u8 *)addr);
+ }
+ spin_unlock_irqrestore(&sc->node_lock, flags);
+ break;
+ case STA_NOTIFY_REMOVE:
+ if (!an)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Removal of a non-existent node\n",
+ __func__);
+ else {
+ ath_node_put(sc, an, ATH9K_BH_STATUS_INTACT);
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Put a node: %s\n",
+ __func__,
+ print_mac(mac, addr));
+ }
+ break;
+ default:
+ break;
+ }
+}
+
+static int ath9k_conf_tx(struct ieee80211_hw *hw,
+ u16 queue,
+ const struct ieee80211_tx_queue_params *params)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath9k_tx_queue_info qi;
+ int ret = 0, qnum;
+
+ if (queue >= WME_NUM_AC)
+ return 0;
+
+ qi.tqi_aifs = params->aifs;
+ qi.tqi_cwmin = params->cw_min;
+ qi.tqi_cwmax = params->cw_max;
+ qi.tqi_burstTime = params->txop;
+ qnum = ath_get_hal_qnum(queue, sc);
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Configure tx [queue/halq] [%d/%d], "
+ "aifs: %d, cw_min: %d, cw_max: %d, txop: %d\n",
+ __func__,
+ queue,
+ qnum,
+ params->aifs,
+ params->cw_min,
+ params->cw_max,
+ params->txop);
+
+ ret = ath_txq_update(sc, qnum, &qi);
+ if (ret)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: TXQ Update failed\n", __func__);
+
+ return ret;
+}
+
+static int ath9k_set_key(struct ieee80211_hw *hw,
+ enum set_key_cmd cmd,
+ const u8 *local_addr,
+ const u8 *addr,
+ struct ieee80211_key_conf *key)
+{
+ struct ath_softc *sc = hw->priv;
+ int ret = 0;
+
+ DPRINTF(sc, ATH_DBG_KEYCACHE, " %s: Set HW Key\n", __func__);
+
+ switch (cmd) {
+ case SET_KEY:
+ ret = ath_key_config(sc, addr, key);
+ if (!ret) {
+ set_bit(key->keyidx, sc->sc_keymap);
+ key->hw_key_idx = key->keyidx;
+ /* push IV and Michael MIC generation to stack */
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC;
+ }
+ break;
+ case DISABLE_KEY:
+ ath_key_delete(sc, key);
+ clear_bit(key->keyidx, sc->sc_keymap);
+ sc->sc_keytype = ATH9K_CIPHER_CLR;
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static void ath9k_ht_conf(struct ath_softc *sc,
+ struct ieee80211_bss_conf *bss_conf)
+{
+#define IEEE80211_HT_CAP_40MHZ_INTOLERANT BIT(14)
+ struct ath_ht_info *ht_info = &sc->sc_ht_info;
+
+ if (bss_conf->assoc_ht) {
+ ht_info->ext_chan_offset =
+ bss_conf->ht_bss_conf->bss_cap &
+ IEEE80211_HT_IE_CHA_SEC_OFFSET;
+
+ if (!(bss_conf->ht_conf->cap &
+ IEEE80211_HT_CAP_40MHZ_INTOLERANT) &&
+ (bss_conf->ht_bss_conf->bss_cap &
+ IEEE80211_HT_IE_CHA_WIDTH))
+ ht_info->tx_chan_width = ATH9K_HT_MACMODE_2040;
+ else
+ ht_info->tx_chan_width = ATH9K_HT_MACMODE_20;
+
+ ath9k_hw_set11nmac2040(sc->sc_ah, ht_info->tx_chan_width);
+ ht_info->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR +
+ bss_conf->ht_conf->ampdu_factor);
+ ht_info->mpdudensity =
+ parse_mpdudensity(bss_conf->ht_conf->ampdu_density);
+
+ }
+
+#undef IEEE80211_HT_CAP_40MHZ_INTOLERANT
+}
+
+static void ath9k_bss_assoc_info(struct ath_softc *sc,
+ struct ieee80211_bss_conf *bss_conf)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_channel *curchan = hw->conf.channel;
+ struct ath_vap *avp;
+ int pos;
+ DECLARE_MAC_BUF(mac);
+
+ if (bss_conf->assoc) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Bss Info ASSOC %d\n",
+ __func__,
+ bss_conf->aid);
+
+ avp = sc->sc_vaps[0];
+ if (avp == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid interface\n",
+ __func__);
+ return;
+ }
+
+ /* New association, store aid */
+ if (avp->av_opmode == ATH9K_M_STA) {
+ sc->sc_curaid = bss_conf->aid;
+ ath9k_hw_write_associd(sc->sc_ah, sc->sc_curbssid,
+ sc->sc_curaid);
+ }
+
+ /* Configure the beacon */
+ ath_beacon_config(sc, 0);
+ sc->sc_beacons = 1;
+
+ /* Reset rssi stats */
+ sc->sc_halstats.ns_avgbrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgtxrssi = ATH_RSSI_DUMMY_MARKER;
+ sc->sc_halstats.ns_avgtxrate = ATH_RATE_DUMMY_MARKER;
+
+ /* Update chainmask */
+ ath_update_chainmask(sc, bss_conf->assoc_ht);
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: bssid %s aid 0x%x\n",
+ __func__,
+ print_mac(mac, sc->sc_curbssid), sc->sc_curaid);
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Set channel: %d MHz\n",
+ __func__,
+ curchan->center_freq);
+
+ pos = ath_get_channel(sc, curchan);
+ if (pos == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Invalid channel\n", __func__);
+ return;
+ }
+
+ if (hw->conf.ht_conf.ht_supported)
+ sc->sc_ah->ah_channels[pos].chanmode =
+ ath_get_extchanmode(sc, curchan);
+ else
+ sc->sc_ah->ah_channels[pos].chanmode =
+ (curchan->band == IEEE80211_BAND_2GHZ) ?
+ CHANNEL_G : CHANNEL_A;
+
+ /* set h/w channel */
+ if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to set channel\n",
+ __func__);
+
+ ath_rate_newstate(sc, avp);
+ /* Update ratectrl about the new state */
+ ath_rc_node_update(hw, avp->rc_node);
+ } else {
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Bss Info DISSOC\n", __func__);
+ sc->sc_curaid = 0;
+ }
+}
+
+static void ath9k_bss_info_changed(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_bss_conf *bss_conf,
+ u32 changed)
+{
+ struct ath_softc *sc = hw->priv;
+
+ if (changed & BSS_CHANGED_ERP_PREAMBLE) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: BSS Changed PREAMBLE %d\n",
+ __func__,
+ bss_conf->use_short_preamble);
+ if (bss_conf->use_short_preamble)
+ sc->sc_flags |= ATH_PREAMBLE_SHORT;
+ else
+ sc->sc_flags &= ~ATH_PREAMBLE_SHORT;
+ }
+
+ if (changed & BSS_CHANGED_ERP_CTS_PROT) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: BSS Changed CTS PROT %d\n",
+ __func__,
+ bss_conf->use_cts_prot);
+ if (bss_conf->use_cts_prot &&
+ hw->conf.channel->band != IEEE80211_BAND_5GHZ)
+ sc->sc_flags |= ATH_PROTECT_ENABLE;
+ else
+ sc->sc_flags &= ~ATH_PROTECT_ENABLE;
+ }
+
+ if (changed & BSS_CHANGED_HT) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: BSS Changed HT %d\n",
+ __func__,
+ bss_conf->assoc_ht);
+ ath9k_ht_conf(sc, bss_conf);
+ }
+
+ if (changed & BSS_CHANGED_ASSOC) {
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: BSS Changed ASSOC %d\n",
+ __func__,
+ bss_conf->assoc);
+ ath9k_bss_assoc_info(sc, bss_conf);
+ }
+}
+
+static u64 ath9k_get_tsf(struct ieee80211_hw *hw)
+{
+ u64 tsf;
+ struct ath_softc *sc = hw->priv;
+ struct ath_hal *ah = sc->sc_ah;
+
+ tsf = ath9k_hw_gettsf64(ah);
+
+ return tsf;
+}
+
+static void ath9k_reset_tsf(struct ieee80211_hw *hw)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath_hal *ah = sc->sc_ah;
+
+ ath9k_hw_reset_tsf(ah);
+}
+
+static int ath9k_ampdu_action(struct ieee80211_hw *hw,
+ enum ieee80211_ampdu_mlme_action action,
+ const u8 *addr,
+ u16 tid,
+ u16 *ssn)
+{
+ struct ath_softc *sc = hw->priv;
+ int ret = 0;
+
+ switch (action) {
+ case IEEE80211_AMPDU_RX_START:
+ ret = ath_rx_aggr_start(sc, addr, tid, ssn);
+ if (ret < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to start RX aggregation\n",
+ __func__);
+ break;
+ case IEEE80211_AMPDU_RX_STOP:
+ ret = ath_rx_aggr_stop(sc, addr, tid);
+ if (ret < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to stop RX aggregation\n",
+ __func__);
+ break;
+ case IEEE80211_AMPDU_TX_START:
+ ret = ath_tx_aggr_start(sc, addr, tid, ssn);
+ if (ret < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to start TX aggregation\n",
+ __func__);
+ else
+ ieee80211_start_tx_ba_cb_irqsafe(hw, (u8 *)addr, tid);
+ break;
+ case IEEE80211_AMPDU_TX_STOP:
+ ret = ath_tx_aggr_stop(sc, addr, tid);
+ if (ret < 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to stop TX aggregation\n",
+ __func__);
+
+ ieee80211_stop_tx_ba_cb_irqsafe(hw, (u8 *)addr, tid);
+ break;
+ default:
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unknown AMPDU action\n", __func__);
+ }
+
+ return ret;
+}
+
+static struct ieee80211_ops ath9k_ops = {
+ .tx = ath9k_tx,
+ .start = ath9k_start,
+ .stop = ath9k_stop,
+ .add_interface = ath9k_add_interface,
+ .remove_interface = ath9k_remove_interface,
+ .config = ath9k_config,
+ .config_interface = ath9k_config_interface,
+ .configure_filter = ath9k_configure_filter,
+ .get_stats = NULL,
+ .sta_notify = ath9k_sta_notify,
+ .conf_tx = ath9k_conf_tx,
+ .get_tx_stats = NULL,
+ .bss_info_changed = ath9k_bss_info_changed,
+ .set_tim = NULL,
+ .set_key = ath9k_set_key,
+ .hw_scan = NULL,
+ .get_tkip_seq = NULL,
+ .set_rts_threshold = NULL,
+ .set_frag_threshold = NULL,
+ .set_retry_limit = NULL,
+ .get_tsf = ath9k_get_tsf,
+ .reset_tsf = ath9k_reset_tsf,
+ .tx_last_beacon = NULL,
+ .ampdu_action = ath9k_ampdu_action
+};
+
+void ath_get_beaconconfig(struct ath_softc *sc,
+ int if_id,
+ struct ath_beacon_config *conf)
+{
+ struct ieee80211_hw *hw = sc->hw;
+
+ /* fill in beacon config data */
+
+ conf->beacon_interval = hw->conf.beacon_int;
+ conf->listen_interval = 100;
+ conf->dtim_count = 1;
+ conf->bmiss_timeout = ATH_DEFAULT_BMISS_LIMIT * conf->listen_interval;
+}
+
+int ath_update_beacon(struct ath_softc *sc,
+ int if_id,
+ struct ath_beacon_offset *bo,
+ struct sk_buff *skb,
+ int mcast)
+{
+ return 0;
+}
+
+void ath_tx_complete(struct ath_softc *sc, struct sk_buff *skb,
+ struct ath_xmit_status *tx_status, struct ath_node *an)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+
+ DPRINTF(sc, ATH_DBG_XMIT,
+ "%s: TX complete: skb: %p\n", __func__, skb);
+
+ if (tx_info->flags & IEEE80211_TX_CTL_NO_ACK ||
+ tx_info->flags & IEEE80211_TX_STAT_TX_FILTERED) {
+ /* free driver's private data area of tx_info */
+ if (tx_info->driver_data[0] != NULL)
+ kfree(tx_info->driver_data[0]);
+ tx_info->driver_data[0] = NULL;
+ }
+
+ if (tx_status->flags & ATH_TX_BAR) {
+ tx_info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK;
+ tx_status->flags &= ~ATH_TX_BAR;
+ }
+ if (tx_status->flags)
+ tx_info->status.excessive_retries = 1;
+
+ tx_info->status.retry_count = tx_status->retries;
+
+ ieee80211_tx_status(hw, skb);
+ if (an)
+ ath_node_put(sc, an, ATH9K_BH_STATUS_CHANGE);
+}
+
+int ath__rx_indicate(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_recv_status *status,
+ u16 keyix)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ath_node *an = NULL;
+ struct ieee80211_rx_status rx_status;
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ int hdrlen = ieee80211_get_hdrlen_from_skb(skb);
+ int padsize;
+ enum ATH_RX_TYPE st;
+
+ /* see if any padding is done by the hw and remove it */
+ if (hdrlen & 3) {
+ padsize = hdrlen % 4;
+ memmove(skb->data + padsize, skb->data, hdrlen);
+ skb_pull(skb, padsize);
+ }
+
+ /* remove FCS before passing up to protocol stack */
+ skb_trim(skb, (skb->len - FCS_LEN));
+
+ /* Prepare rx status */
+ ath9k_rx_prepare(sc, skb, status, &rx_status);
+
+ if (!(keyix == ATH9K_RXKEYIX_INVALID) &&
+ !(status->flags & ATH_RX_DECRYPT_ERROR)) {
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+ } else if ((le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_PROTECTED)
+ && !(status->flags & ATH_RX_DECRYPT_ERROR)
+ && skb->len >= hdrlen + 4) {
+ keyix = skb->data[hdrlen + 3] >> 6;
+
+ if (test_bit(keyix, sc->sc_keymap))
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+ }
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, hdr->addr2);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (an) {
+ ath_rx_input(sc, an,
+ hw->conf.ht_conf.ht_supported,
+ skb, status, &st);
+ }
+ if (!an || (st != ATH_RX_CONSUMED))
+ __ieee80211_rx(hw, skb, &rx_status);
+
+ return 0;
+}
+
+int ath_rx_subframe(struct ath_node *an,
+ struct sk_buff *skb,
+ struct ath_recv_status *status)
+{
+ struct ath_softc *sc = an->an_sc;
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_rx_status rx_status;
+
+ /* Prepare rx status */
+ ath9k_rx_prepare(sc, skb, status, &rx_status);
+ if (!(status->flags & ATH_RX_DECRYPT_ERROR))
+ rx_status.flag |= RX_FLAG_DECRYPTED;
+
+ __ieee80211_rx(hw, skb, &rx_status);
+
+ return 0;
+}
+
+enum ath9k_ht_macmode ath_cwm_macmode(struct ath_softc *sc)
+{
+ return sc->sc_ht_info.tx_chan_width;
+}
+
+static int ath_detach(struct ath_softc *sc)
+{
+ struct ieee80211_hw *hw = sc->hw;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Detach ATH hw\n", __func__);
+
+ /* Unregister hw */
+
+ ieee80211_unregister_hw(hw);
+
+ /* unregister Rate control */
+ ath_rate_control_unregister();
+
+ /* tx/rx cleanup */
+
+ ath_rx_cleanup(sc);
+ ath_tx_cleanup(sc);
+
+ /* Deinit */
+
+ ath_deinit(sc);
+
+ return 0;
+}
+
+static int ath_attach(u16 devid,
+ struct ath_softc *sc)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ int error = 0;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Attach ATH hw\n", __func__);
+
+ error = ath_init(devid, sc);
+ if (error != 0)
+ return error;
+
+ /* Init nodes */
+
+ INIT_LIST_HEAD(&sc->node_list);
+ spin_lock_init(&sc->node_lock);
+
+ /* get mac address from hardware and set in mac80211 */
+
+ SET_IEEE80211_PERM_ADDR(hw, sc->sc_myaddr);
+
+ /* setup channels and rates */
+
+ sc->sbands[IEEE80211_BAND_2GHZ].channels =
+ sc->channels[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ /* Setup HT capabilities for 2.4Ghz*/
+ setup_ht_cap(&sc->sbands[IEEE80211_BAND_2GHZ].ht_info);
+
+ hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
+ &sc->sbands[IEEE80211_BAND_2GHZ];
+
+ if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) {
+ sc->sbands[IEEE80211_BAND_5GHZ].channels =
+ sc->channels[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].band =
+ IEEE80211_BAND_5GHZ;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ /* Setup HT capabilities for 5Ghz*/
+ setup_ht_cap(&sc->sbands[IEEE80211_BAND_5GHZ].ht_info);
+
+ hw->wiphy->bands[IEEE80211_BAND_5GHZ] =
+ &sc->sbands[IEEE80211_BAND_5GHZ];
+ }
+
+ /* FIXME: Have to figure out proper hw init values later */
+
+ hw->queues = 4;
+ hw->ampdu_queues = 1;
+
+ /* Register rate control */
+ hw->rate_control_algorithm = "ath9k_rate_control";
+ error = ath_rate_control_register();
+ if (error != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: Unable to register rate control "
+ "algorithm:%d\n", __func__, error);
+ ath_rate_control_unregister();
+ goto bad;
+ }
+
+ error = ieee80211_register_hw(hw);
+ if (error != 0) {
+ ath_rate_control_unregister();
+ goto bad;
+ }
+
+ /* initialize tx/rx engine */
+
+ error = ath_tx_init(sc, ATH_TXBUF);
+ if (error != 0)
+ goto bad1;
+
+ error = ath_rx_init(sc, ATH_RXBUF);
+ if (error != 0)
+ goto bad1;
+
+ return 0;
+bad1:
+ ath_detach(sc);
+bad:
+ return error;
+}
+
+static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ void __iomem *mem;
+ struct ath_softc *sc;
+ struct ieee80211_hw *hw;
+ const char *athname;
+ u8 csz;
+ u32 val;
+ int ret = 0;
+
+ if (pci_enable_device(pdev))
+ return -EIO;
+
+ /* XXX 32-bit addressing only */
+ if (pci_set_dma_mask(pdev, 0xffffffff)) {
+ printk(KERN_ERR "ath_pci: 32-bit DMA not available\n");
+ ret = -ENODEV;
+ goto bad;
+ }
+
+ /*
+ * Cache line size is used to size and align various
+ * structures used to communicate with the hardware.
+ */
+ pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz);
+ if (csz == 0) {
+ /*
+ * Linux 2.4.18 (at least) writes the cache line size
+ * register as a 16-bit wide register which is wrong.
+ * We must have this setup properly for rx buffer
+ * DMA to work so force a reasonable value here if it
+ * comes up zero.
+ */
+ csz = L1_CACHE_BYTES / sizeof(u32);
+ pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz);
+ }
+ /*
+ * The default setting of latency timer yields poor results,
+ * set it to the value used by other systems. It may be worth
+ * tweaking this setting more.
+ */
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8);
+
+ pci_set_master(pdev);
+
+ /*
+ * Disable the RETRY_TIMEOUT register (0x41) to keep
+ * PCI Tx retries from interfering with C3 CPU state.
+ */
+ pci_read_config_dword(pdev, 0x40, &val);
+ if ((val & 0x0000ff00) != 0)
+ pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
+
+ ret = pci_request_region(pdev, 0, "ath9k");
+ if (ret) {
+ dev_err(&pdev->dev, "PCI memory region reserve error\n");
+ ret = -ENODEV;
+ goto bad;
+ }
+
+ mem = pci_iomap(pdev, 0, 0);
+ if (!mem) {
+ printk(KERN_ERR "PCI memory map error\n") ;
+ ret = -EIO;
+ goto bad1;
+ }
+
+ hw = ieee80211_alloc_hw(sizeof(struct ath_softc), &ath9k_ops);
+ if (hw == NULL) {
+ printk(KERN_ERR "ath_pci: no memory for ieee80211_hw\n");
+ goto bad2;
+ }
+
+ hw->flags = IEEE80211_HW_SIGNAL_DBM |
+ IEEE80211_HW_NOISE_DBM;
+
+ SET_IEEE80211_DEV(hw, &pdev->dev);
+ pci_set_drvdata(pdev, hw);
+
+ sc = hw->priv;
+ sc->hw = hw;
+ sc->pdev = pdev;
+ sc->mem = mem;
+
+ if (ath_attach(id->device, sc) != 0) {
+ ret = -ENODEV;
+ goto bad3;
+ }
+
+ /* setup interrupt service routine */
+
+ if (request_irq(pdev->irq, ath_isr, IRQF_SHARED, "ath", sc)) {
+ printk(KERN_ERR "%s: request_irq failed\n",
+ wiphy_name(hw->wiphy));
+ ret = -EIO;
+ goto bad4;
+ }
+
+ athname = ath9k_hw_probe(id->vendor, id->device);
+
+ printk(KERN_INFO "%s: %s: mem=0x%lx, irq=%d\n",
+ wiphy_name(hw->wiphy),
+ athname ? athname : "Atheros ???",
+ (unsigned long)mem, pdev->irq);
+
+ return 0;
+bad4:
+ ath_detach(sc);
+bad3:
+ ieee80211_free_hw(hw);
+bad2:
+ pci_iounmap(pdev, mem);
+bad1:
+ pci_release_region(pdev, 0);
+bad:
+ pci_disable_device(pdev);
+ return ret;
+}
+
+static void ath_pci_remove(struct pci_dev *pdev)
+{
+ struct ieee80211_hw *hw = pci_get_drvdata(pdev);
+ struct ath_softc *sc = hw->priv;
+
+ if (pdev->irq)
+ free_irq(pdev->irq, sc);
+ ath_detach(sc);
+ pci_iounmap(pdev, sc->mem);
+ pci_release_region(pdev, 0);
+ pci_disable_device(pdev);
+ ieee80211_free_hw(hw);
+}
+
+#ifdef CONFIG_PM
+
+static int ath_pci_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ pci_save_state(pdev);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, 3);
+
+ return 0;
+}
+
+static int ath_pci_resume(struct pci_dev *pdev)
+{
+ u32 val;
+ int err;
+
+ err = pci_enable_device(pdev);
+ if (err)
+ return err;
+ pci_restore_state(pdev);
+ /*
+ * Suspend/Resume resets the PCI configuration space, so we have to
+ * re-disable the RETRY_TIMEOUT register (0x41) to keep
+ * PCI Tx retries from interfering with C3 CPU state
+ */
+ pci_read_config_dword(pdev, 0x40, &val);
+ if ((val & 0x0000ff00) != 0)
+ pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
+
+ return 0;
+}
+
+#endif /* CONFIG_PM */
+
+MODULE_DEVICE_TABLE(pci, ath_pci_id_table);
+
+static struct pci_driver ath_pci_driver = {
+ .name = "ath9k",
+ .id_table = ath_pci_id_table,
+ .probe = ath_pci_probe,
+ .remove = ath_pci_remove,
+#ifdef CONFIG_PM
+ .suspend = ath_pci_suspend,
+ .resume = ath_pci_resume,
+#endif /* CONFIG_PM */
+};
+
+static int __init init_ath_pci(void)
+{
+ printk(KERN_INFO "%s: %s\n", dev_info, ATH_PCI_VERSION);
+
+ if (pci_register_driver(&ath_pci_driver) < 0) {
+ printk(KERN_ERR
+ "ath_pci: No devices found, driver not installed.\n");
+ pci_unregister_driver(&ath_pci_driver);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+module_init(init_ath_pci);
+
+static void __exit exit_ath_pci(void)
+{
+ pci_unregister_driver(&ath_pci_driver);
+ printk(KERN_INFO "%s: driver unloaded\n", dev_info);
+}
+module_exit(exit_ath_pci);
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include "core.h"
+#include "hw.h"
+#include "reg.h"
+#include "phy.h"
+
+void
+ath9k_hw_write_regs(struct ath_hal *ah, u32 modesIndex, u32 freqIndex,
+ int regWrites)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ REG_WRITE_ARRAY(&ahp->ah_iniBB_RfGain, freqIndex, regWrites);
+}
+
+bool
+ath9k_hw_set_channel(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ u32 channelSel = 0;
+ u32 bModeSynth = 0;
+ u32 aModeRefSel = 0;
+ u32 reg32 = 0;
+ u16 freq;
+ struct chan_centers centers;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ freq = centers.synth_center;
+
+ if (freq < 4800) {
+ u32 txctl;
+
+ if (((freq - 2192) % 5) == 0) {
+ channelSel = ((freq - 672) * 2 - 3040) / 10;
+ bModeSynth = 0;
+ } else if (((freq - 2224) % 5) == 0) {
+ channelSel = ((freq - 704) * 2 - 3040) / 10;
+ bModeSynth = 1;
+ } else {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u MHz\n", __func__,
+ freq);
+ return false;
+ }
+
+ channelSel = (channelSel << 2) & 0xff;
+ channelSel = ath9k_hw_reverse_bits(channelSel, 8);
+
+ txctl = REG_READ(ah, AR_PHY_CCK_TX_CTRL);
+ if (freq == 2484) {
+
+ REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
+ txctl | AR_PHY_CCK_TX_CTRL_JAPAN);
+ } else {
+ REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
+ txctl & ~AR_PHY_CCK_TX_CTRL_JAPAN);
+ }
+
+ } else if ((freq % 20) == 0 && freq >= 5120) {
+ channelSel =
+ ath9k_hw_reverse_bits(((freq - 4800) / 20 << 2), 8);
+ aModeRefSel = ath9k_hw_reverse_bits(1, 2);
+ } else if ((freq % 10) == 0) {
+ channelSel =
+ ath9k_hw_reverse_bits(((freq - 4800) / 10 << 1), 8);
+ if (AR_SREV_9100(ah) || AR_SREV_9160_10_OR_LATER(ah))
+ aModeRefSel = ath9k_hw_reverse_bits(2, 2);
+ else
+ aModeRefSel = ath9k_hw_reverse_bits(1, 2);
+ } else if ((freq % 5) == 0) {
+ channelSel = ath9k_hw_reverse_bits((freq - 4800) / 5, 8);
+ aModeRefSel = ath9k_hw_reverse_bits(1, 2);
+ } else {
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL,
+ "%s: invalid channel %u MHz\n", __func__, freq);
+ return false;
+ }
+
+ reg32 =
+ (channelSel << 8) | (aModeRefSel << 2) | (bModeSynth << 1) |
+ (1 << 5) | 0x1;
+
+ REG_WRITE(ah, AR_PHY(0x37), reg32);
+
+ ah->ah_curchan = chan;
+
+ AH5416(ah)->ah_curchanRadIndex = -1;
+
+ return true;
+}
+
+bool
+ath9k_hw_ar9280_set_channel(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ u16 bMode, fracMode, aModeRefSel = 0;
+ u32 freq, ndiv, channelSel = 0, channelFrac = 0, reg32 = 0;
+ struct chan_centers centers;
+ u32 refDivA = 24;
+
+ ath9k_hw_get_channel_centers(ah, chan, ¢ers);
+ freq = centers.synth_center;
+
+ reg32 = REG_READ(ah, AR_PHY_SYNTH_CONTROL);
+ reg32 &= 0xc0000000;
+
+ if (freq < 4800) {
+ u32 txctl;
+
+ bMode = 1;
+ fracMode = 1;
+ aModeRefSel = 0;
+ channelSel = (freq * 0x10000) / 15;
+
+ txctl = REG_READ(ah, AR_PHY_CCK_TX_CTRL);
+ if (freq == 2484) {
+
+ REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
+ txctl | AR_PHY_CCK_TX_CTRL_JAPAN);
+ } else {
+ REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
+ txctl & ~AR_PHY_CCK_TX_CTRL_JAPAN);
+ }
+ } else {
+ bMode = 0;
+ fracMode = 0;
+
+ if ((freq % 20) == 0) {
+ aModeRefSel = 3;
+ } else if ((freq % 10) == 0) {
+ aModeRefSel = 2;
+ } else {
+ aModeRefSel = 0;
+
+ fracMode = 1;
+ refDivA = 1;
+ channelSel = (freq * 0x8000) / 15;
+
+ REG_RMW_FIELD(ah, AR_AN_SYNTH9,
+ AR_AN_SYNTH9_REFDIVA, refDivA);
+ }
+ if (!fracMode) {
+ ndiv = (freq * (refDivA >> aModeRefSel)) / 60;
+ channelSel = ndiv & 0x1ff;
+ channelFrac = (ndiv & 0xfffffe00) * 2;
+ channelSel = (channelSel << 17) | channelFrac;
+ }
+ }
+
+ reg32 = reg32 |
+ (bMode << 29) |
+ (fracMode << 28) | (aModeRefSel << 26) | (channelSel);
+
+ REG_WRITE(ah, AR_PHY_SYNTH_CONTROL, reg32);
+
+ ah->ah_curchan = chan;
+
+ AH5416(ah)->ah_curchanRadIndex = -1;
+
+ return true;
+}
+
+static void
+ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32,
+ u32 numBits, u32 firstBit,
+ u32 column)
+{
+ u32 tmp32, mask, arrayEntry, lastBit;
+ int32_t bitPosition, bitsLeft;
+
+ tmp32 = ath9k_hw_reverse_bits(reg32, numBits);
+ arrayEntry = (firstBit - 1) / 8;
+ bitPosition = (firstBit - 1) % 8;
+ bitsLeft = numBits;
+ while (bitsLeft > 0) {
+ lastBit = (bitPosition + bitsLeft > 8) ?
+ 8 : bitPosition + bitsLeft;
+ mask = (((1 << lastBit) - 1) ^ ((1 << bitPosition) - 1)) <<
+ (column * 8);
+ rfBuf[arrayEntry] &= ~mask;
+ rfBuf[arrayEntry] |= ((tmp32 << bitPosition) <<
+ (column * 8)) & mask;
+ bitsLeft -= 8 - bitPosition;
+ tmp32 = tmp32 >> (8 - bitPosition);
+ bitPosition = 0;
+ arrayEntry++;
+ }
+}
+
+bool
+ath9k_hw_set_rf_regs(struct ath_hal *ah, struct ath9k_channel *chan,
+ u16 modesIndex)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ u32 eepMinorRev;
+ u32 ob5GHz = 0, db5GHz = 0;
+ u32 ob2GHz = 0, db2GHz = 0;
+ int regWrites = 0;
+
+ if (AR_SREV_9280_10_OR_LATER(ah))
+ return true;
+
+ eepMinorRev = ath9k_hw_get_eeprom(ahp, EEP_MINOR_REV);
+
+ RF_BANK_SETUP(ahp->ah_analogBank0Data, &ahp->ah_iniBank0, 1);
+
+ RF_BANK_SETUP(ahp->ah_analogBank1Data, &ahp->ah_iniBank1, 1);
+
+ RF_BANK_SETUP(ahp->ah_analogBank2Data, &ahp->ah_iniBank2, 1);
+
+ RF_BANK_SETUP(ahp->ah_analogBank3Data, &ahp->ah_iniBank3,
+ modesIndex);
+ {
+ int i;
+ for (i = 0; i < ahp->ah_iniBank6TPC.ia_rows; i++) {
+ ahp->ah_analogBank6Data[i] =
+ INI_RA(&ahp->ah_iniBank6TPC, i, modesIndex);
+ }
+ }
+
+ if (eepMinorRev >= 2) {
+ if (IS_CHAN_2GHZ(chan)) {
+ ob2GHz = ath9k_hw_get_eeprom(ahp, EEP_OB_2);
+ db2GHz = ath9k_hw_get_eeprom(ahp, EEP_DB_2);
+ ath9k_phy_modify_rx_buffer(ahp->ah_analogBank6Data,
+ ob2GHz, 3, 197, 0);
+ ath9k_phy_modify_rx_buffer(ahp->ah_analogBank6Data,
+ db2GHz, 3, 194, 0);
+ } else {
+ ob5GHz = ath9k_hw_get_eeprom(ahp, EEP_OB_5);
+ db5GHz = ath9k_hw_get_eeprom(ahp, EEP_DB_5);
+ ath9k_phy_modify_rx_buffer(ahp->ah_analogBank6Data,
+ ob5GHz, 3, 203, 0);
+ ath9k_phy_modify_rx_buffer(ahp->ah_analogBank6Data,
+ db5GHz, 3, 200, 0);
+ }
+ }
+
+ RF_BANK_SETUP(ahp->ah_analogBank7Data, &ahp->ah_iniBank7, 1);
+
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank0, ahp->ah_analogBank0Data,
+ regWrites);
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank1, ahp->ah_analogBank1Data,
+ regWrites);
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank2, ahp->ah_analogBank2Data,
+ regWrites);
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank3, ahp->ah_analogBank3Data,
+ regWrites);
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank6TPC, ahp->ah_analogBank6Data,
+ regWrites);
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank7, ahp->ah_analogBank7Data,
+ regWrites);
+
+ return true;
+}
+
+void
+ath9k_hw_rfdetach(struct ath_hal *ah)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (ahp->ah_analogBank0Data != NULL) {
+ kfree(ahp->ah_analogBank0Data);
+ ahp->ah_analogBank0Data = NULL;
+ }
+ if (ahp->ah_analogBank1Data != NULL) {
+ kfree(ahp->ah_analogBank1Data);
+ ahp->ah_analogBank1Data = NULL;
+ }
+ if (ahp->ah_analogBank2Data != NULL) {
+ kfree(ahp->ah_analogBank2Data);
+ ahp->ah_analogBank2Data = NULL;
+ }
+ if (ahp->ah_analogBank3Data != NULL) {
+ kfree(ahp->ah_analogBank3Data);
+ ahp->ah_analogBank3Data = NULL;
+ }
+ if (ahp->ah_analogBank6Data != NULL) {
+ kfree(ahp->ah_analogBank6Data);
+ ahp->ah_analogBank6Data = NULL;
+ }
+ if (ahp->ah_analogBank6TPCData != NULL) {
+ kfree(ahp->ah_analogBank6TPCData);
+ ahp->ah_analogBank6TPCData = NULL;
+ }
+ if (ahp->ah_analogBank7Data != NULL) {
+ kfree(ahp->ah_analogBank7Data);
+ ahp->ah_analogBank7Data = NULL;
+ }
+ if (ahp->ah_addac5416_21 != NULL) {
+ kfree(ahp->ah_addac5416_21);
+ ahp->ah_addac5416_21 = NULL;
+ }
+ if (ahp->ah_bank6Temp != NULL) {
+ kfree(ahp->ah_bank6Temp);
+ ahp->ah_bank6Temp = NULL;
+ }
+}
+
+bool ath9k_hw_init_rf(struct ath_hal *ah, int *status)
+{
+ struct ath_hal_5416 *ahp = AH5416(ah);
+
+ if (!AR_SREV_9280_10_OR_LATER(ah)) {
+
+ ahp->ah_analogBank0Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank0.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank1Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank1.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank2Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank2.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank3Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank3.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank6Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank6.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank6TPCData =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank6TPC.ia_rows), GFP_KERNEL);
+ ahp->ah_analogBank7Data =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank7.ia_rows), GFP_KERNEL);
+
+ if (ahp->ah_analogBank0Data == NULL
+ || ahp->ah_analogBank1Data == NULL
+ || ahp->ah_analogBank2Data == NULL
+ || ahp->ah_analogBank3Data == NULL
+ || ahp->ah_analogBank6Data == NULL
+ || ahp->ah_analogBank6TPCData == NULL
+ || ahp->ah_analogBank7Data == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_FATAL,
+ "%s: cannot allocate RF banks\n",
+ __func__);
+ *status = -ENOMEM;
+ return false;
+ }
+
+ ahp->ah_addac5416_21 =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniAddac.ia_rows *
+ ahp->ah_iniAddac.ia_columns), GFP_KERNEL);
+ if (ahp->ah_addac5416_21 == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_FATAL,
+ "%s: cannot allocate ah_addac5416_21\n",
+ __func__);
+ *status = -ENOMEM;
+ return false;
+ }
+
+ ahp->ah_bank6Temp =
+ kzalloc((sizeof(u32) *
+ ahp->ah_iniBank6.ia_rows), GFP_KERNEL);
+ if (ahp->ah_bank6Temp == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_FATAL,
+ "%s: cannot allocate ah_bank6Temp\n",
+ __func__);
+ *status = -ENOMEM;
+ return false;
+ }
+ }
+
+ return true;
+}
+
+void
+ath9k_hw_decrease_chain_power(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ int i, regWrites = 0;
+ struct ath_hal_5416 *ahp = AH5416(ah);
+ u32 bank6SelMask;
+ u32 *bank6Temp = ahp->ah_bank6Temp;
+
+ switch (ahp->ah_diversityControl) {
+ case ATH9K_ANT_FIXED_A:
+ bank6SelMask =
+ (ahp->
+ ah_antennaSwitchSwap & ANTSWAP_AB) ? REDUCE_CHAIN_0 :
+ REDUCE_CHAIN_1;
+ break;
+ case ATH9K_ANT_FIXED_B:
+ bank6SelMask =
+ (ahp->
+ ah_antennaSwitchSwap & ANTSWAP_AB) ? REDUCE_CHAIN_1 :
+ REDUCE_CHAIN_0;
+ break;
+ case ATH9K_ANT_VARIABLE:
+ return;
+ break;
+ default:
+ return;
+ break;
+ }
+
+ for (i = 0; i < ahp->ah_iniBank6.ia_rows; i++)
+ bank6Temp[i] = ahp->ah_analogBank6Data[i];
+
+ REG_WRITE(ah, AR_PHY_BASE + 0xD8, bank6SelMask);
+
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 189, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 190, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 191, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 192, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 193, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 222, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 245, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 246, 0);
+ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 247, 0);
+
+ REG_WRITE_RF_ARRAY(&ahp->ah_iniBank6, bank6Temp, regWrites);
+
+ REG_WRITE(ah, AR_PHY_BASE + 0xD8, 0x00000053);
+#ifdef ALTER_SWITCH
+ REG_WRITE(ah, PHY_SWITCH_CHAIN_0,
+ (REG_READ(ah, PHY_SWITCH_CHAIN_0) & ~0x38)
+ | ((REG_READ(ah, PHY_SWITCH_CHAIN_0) >> 3) & 0x38));
+#endif
+}
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef PHY_H
+#define PHY_H
+
+bool ath9k_hw_ar9280_set_channel(struct ath_hal *ah,
+ struct ath9k_channel
+ *chan);
+bool ath9k_hw_set_channel(struct ath_hal *ah,
+ struct ath9k_channel *chan);
+void ath9k_hw_write_regs(struct ath_hal *ah, u32 modesIndex,
+ u32 freqIndex, int regWrites);
+bool ath9k_hw_set_rf_regs(struct ath_hal *ah,
+ struct ath9k_channel *chan,
+ u16 modesIndex);
+void ath9k_hw_decrease_chain_power(struct ath_hal *ah,
+ struct ath9k_channel *chan);
+bool ath9k_hw_init_rf(struct ath_hal *ah,
+ int *status);
+
+#define AR_PHY_BASE 0x9800
+#define AR_PHY(_n) (AR_PHY_BASE + ((_n)<<2))
+
+#define AR_PHY_TEST 0x9800
+#define PHY_AGC_CLR 0x10000000
+#define RFSILENT_BB 0x00002000
+
+#define AR_PHY_TURBO 0x9804
+#define AR_PHY_FC_TURBO_MODE 0x00000001
+#define AR_PHY_FC_TURBO_SHORT 0x00000002
+#define AR_PHY_FC_DYN2040_EN 0x00000004
+#define AR_PHY_FC_DYN2040_PRI_ONLY 0x00000008
+#define AR_PHY_FC_DYN2040_PRI_CH 0x00000010
+#define AR_PHY_FC_DYN2040_EXT_CH 0x00000020
+#define AR_PHY_FC_HT_EN 0x00000040
+#define AR_PHY_FC_SHORT_GI_40 0x00000080
+#define AR_PHY_FC_WALSH 0x00000100
+#define AR_PHY_FC_SINGLE_HT_LTF1 0x00000200
+
+#define AR_PHY_TIMING2 0x9810
+#define AR_PHY_TIMING3 0x9814
+#define AR_PHY_TIMING3_DSC_MAN 0xFFFE0000
+#define AR_PHY_TIMING3_DSC_MAN_S 17
+#define AR_PHY_TIMING3_DSC_EXP 0x0001E000
+#define AR_PHY_TIMING3_DSC_EXP_S 13
+
+#define AR_PHY_CHIP_ID 0x9818
+#define AR_PHY_CHIP_ID_REV_0 0x80
+#define AR_PHY_CHIP_ID_REV_1 0x81
+#define AR_PHY_CHIP_ID_9160_REV_0 0xb0
+
+#define AR_PHY_ACTIVE 0x981C
+#define AR_PHY_ACTIVE_EN 0x00000001
+#define AR_PHY_ACTIVE_DIS 0x00000000
+
+#define AR_PHY_RF_CTL2 0x9824
+#define AR_PHY_TX_END_DATA_START 0x000000FF
+#define AR_PHY_TX_END_DATA_START_S 0
+#define AR_PHY_TX_END_PA_ON 0x0000FF00
+#define AR_PHY_TX_END_PA_ON_S 8
+
+#define AR_PHY_RF_CTL3 0x9828
+#define AR_PHY_TX_END_TO_A2_RX_ON 0x00FF0000
+#define AR_PHY_TX_END_TO_A2_RX_ON_S 16
+
+#define AR_PHY_ADC_CTL 0x982C
+#define AR_PHY_ADC_CTL_OFF_INBUFGAIN 0x00000003
+#define AR_PHY_ADC_CTL_OFF_INBUFGAIN_S 0
+#define AR_PHY_ADC_CTL_OFF_PWDDAC 0x00002000
+#define AR_PHY_ADC_CTL_OFF_PWDBANDGAP 0x00004000
+#define AR_PHY_ADC_CTL_OFF_PWDADC 0x00008000
+#define AR_PHY_ADC_CTL_ON_INBUFGAIN 0x00030000
+#define AR_PHY_ADC_CTL_ON_INBUFGAIN_S 16
+
+#define AR_PHY_ADC_SERIAL_CTL 0x9830
+#define AR_PHY_SEL_INTERNAL_ADDAC 0x00000000
+#define AR_PHY_SEL_EXTERNAL_RADIO 0x00000001
+
+#define AR_PHY_RF_CTL4 0x9834
+#define AR_PHY_RF_CTL4_TX_END_XPAB_OFF 0xFF000000
+#define AR_PHY_RF_CTL4_TX_END_XPAB_OFF_S 24
+#define AR_PHY_RF_CTL4_TX_END_XPAA_OFF 0x00FF0000
+#define AR_PHY_RF_CTL4_TX_END_XPAA_OFF_S 16
+#define AR_PHY_RF_CTL4_FRAME_XPAB_ON 0x0000FF00
+#define AR_PHY_RF_CTL4_FRAME_XPAB_ON_S 8
+#define AR_PHY_RF_CTL4_FRAME_XPAA_ON 0x000000FF
+#define AR_PHY_RF_CTL4_FRAME_XPAA_ON_S 0
+
+#define AR_PHY_SETTLING 0x9844
+#define AR_PHY_SETTLING_SWITCH 0x00003F80
+#define AR_PHY_SETTLING_SWITCH_S 7
+
+#define AR_PHY_RXGAIN 0x9848
+#define AR_PHY_RXGAIN_TXRX_ATTEN 0x0003F000
+#define AR_PHY_RXGAIN_TXRX_ATTEN_S 12
+#define AR_PHY_RXGAIN_TXRX_RF_MAX 0x007C0000
+#define AR_PHY_RXGAIN_TXRX_RF_MAX_S 18
+#define AR9280_PHY_RXGAIN_TXRX_ATTEN 0x00003F80
+#define AR9280_PHY_RXGAIN_TXRX_ATTEN_S 7
+#define AR9280_PHY_RXGAIN_TXRX_MARGIN 0x001FC000
+#define AR9280_PHY_RXGAIN_TXRX_MARGIN_S 14
+
+#define AR_PHY_DESIRED_SZ 0x9850
+#define AR_PHY_DESIRED_SZ_ADC 0x000000FF
+#define AR_PHY_DESIRED_SZ_ADC_S 0
+#define AR_PHY_DESIRED_SZ_PGA 0x0000FF00
+#define AR_PHY_DESIRED_SZ_PGA_S 8
+#define AR_PHY_DESIRED_SZ_TOT_DES 0x0FF00000
+#define AR_PHY_DESIRED_SZ_TOT_DES_S 20
+
+#define AR_PHY_FIND_SIG 0x9858
+#define AR_PHY_FIND_SIG_FIRSTEP 0x0003F000
+#define AR_PHY_FIND_SIG_FIRSTEP_S 12
+#define AR_PHY_FIND_SIG_FIRPWR 0x03FC0000
+#define AR_PHY_FIND_SIG_FIRPWR_S 18
+
+#define AR_PHY_AGC_CTL1 0x985C
+#define AR_PHY_AGC_CTL1_COARSE_LOW 0x00007F80
+#define AR_PHY_AGC_CTL1_COARSE_LOW_S 7
+#define AR_PHY_AGC_CTL1_COARSE_HIGH 0x003F8000
+#define AR_PHY_AGC_CTL1_COARSE_HIGH_S 15
+
+#define AR_PHY_AGC_CONTROL 0x9860
+#define AR_PHY_AGC_CONTROL_CAL 0x00000001
+#define AR_PHY_AGC_CONTROL_NF 0x00000002
+#define AR_PHY_AGC_CONTROL_ENABLE_NF 0x00008000
+#define AR_PHY_AGC_CONTROL_FLTR_CAL 0x00010000
+#define AR_PHY_AGC_CONTROL_NO_UPDATE_NF 0x00020000
+
+#define AR_PHY_CCA 0x9864
+#define AR_PHY_MINCCA_PWR 0x0FF80000
+#define AR_PHY_MINCCA_PWR_S 19
+#define AR_PHY_CCA_THRESH62 0x0007F000
+#define AR_PHY_CCA_THRESH62_S 12
+#define AR9280_PHY_MINCCA_PWR 0x1FF00000
+#define AR9280_PHY_MINCCA_PWR_S 20
+#define AR9280_PHY_CCA_THRESH62 0x000FF000
+#define AR9280_PHY_CCA_THRESH62_S 12
+
+#define AR_PHY_SFCORR_LOW 0x986C
+#define AR_PHY_SFCORR_LOW_USE_SELF_CORR_LOW 0x00000001
+#define AR_PHY_SFCORR_LOW_M2COUNT_THR_LOW 0x00003F00
+#define AR_PHY_SFCORR_LOW_M2COUNT_THR_LOW_S 8
+#define AR_PHY_SFCORR_LOW_M1_THRESH_LOW 0x001FC000
+#define AR_PHY_SFCORR_LOW_M1_THRESH_LOW_S 14
+#define AR_PHY_SFCORR_LOW_M2_THRESH_LOW 0x0FE00000
+#define AR_PHY_SFCORR_LOW_M2_THRESH_LOW_S 21
+
+#define AR_PHY_SFCORR 0x9868
+#define AR_PHY_SFCORR_M2COUNT_THR 0x0000001F
+#define AR_PHY_SFCORR_M2COUNT_THR_S 0
+#define AR_PHY_SFCORR_M1_THRESH 0x00FE0000
+#define AR_PHY_SFCORR_M1_THRESH_S 17
+#define AR_PHY_SFCORR_M2_THRESH 0x7F000000
+#define AR_PHY_SFCORR_M2_THRESH_S 24
+
+#define AR_PHY_SLEEP_CTR_CONTROL 0x9870
+#define AR_PHY_SLEEP_CTR_LIMIT 0x9874
+#define AR_PHY_SYNTH_CONTROL 0x9874
+#define AR_PHY_SLEEP_SCAL 0x9878
+
+#define AR_PHY_PLL_CTL 0x987c
+#define AR_PHY_PLL_CTL_40 0xaa
+#define AR_PHY_PLL_CTL_40_5413 0x04
+#define AR_PHY_PLL_CTL_44 0xab
+#define AR_PHY_PLL_CTL_44_2133 0xeb
+#define AR_PHY_PLL_CTL_40_2133 0xea
+
+#define AR_PHY_RX_DELAY 0x9914
+#define AR_PHY_SEARCH_START_DELAY 0x9918
+#define AR_PHY_RX_DELAY_DELAY 0x00003FFF
+
+#define AR_PHY_TIMING_CTRL4(_i) (0x9920 + ((_i) << 12))
+#define AR_PHY_TIMING_CTRL4_IQCORR_Q_Q_COFF 0x01F
+#define AR_PHY_TIMING_CTRL4_IQCORR_Q_Q_COFF_S 0
+#define AR_PHY_TIMING_CTRL4_IQCORR_Q_I_COFF 0x7E0
+#define AR_PHY_TIMING_CTRL4_IQCORR_Q_I_COFF_S 5
+#define AR_PHY_TIMING_CTRL4_IQCORR_ENABLE 0x800
+#define AR_PHY_TIMING_CTRL4_IQCAL_LOG_COUNT_MAX 0xF000
+#define AR_PHY_TIMING_CTRL4_IQCAL_LOG_COUNT_MAX_S 12
+#define AR_PHY_TIMING_CTRL4_DO_CAL 0x10000
+
+#define AR_PHY_TIMING_CTRL4_ENABLE_SPUR_RSSI 0x80000000
+#define AR_PHY_TIMING_CTRL4_ENABLE_SPUR_FILTER 0x40000000
+#define AR_PHY_TIMING_CTRL4_ENABLE_CHAN_MASK 0x20000000
+#define AR_PHY_TIMING_CTRL4_ENABLE_PILOT_MASK 0x10000000
+
+#define AR_PHY_TIMING5 0x9924
+#define AR_PHY_TIMING5_CYCPWR_THR1 0x000000FE
+#define AR_PHY_TIMING5_CYCPWR_THR1_S 1
+
+#define AR_PHY_POWER_TX_RATE1 0x9934
+#define AR_PHY_POWER_TX_RATE2 0x9938
+#define AR_PHY_POWER_TX_RATE_MAX 0x993c
+#define AR_PHY_POWER_TX_RATE_MAX_TPC_ENABLE 0x00000040
+
+#define AR_PHY_FRAME_CTL 0x9944
+#define AR_PHY_FRAME_CTL_TX_CLIP 0x00000038
+#define AR_PHY_FRAME_CTL_TX_CLIP_S 3
+
+#define AR_PHY_TXPWRADJ 0x994C
+#define AR_PHY_TXPWRADJ_CCK_GAIN_DELTA 0x00000FC0
+#define AR_PHY_TXPWRADJ_CCK_GAIN_DELTA_S 6
+#define AR_PHY_TXPWRADJ_CCK_PCDAC_INDEX 0x00FC0000
+#define AR_PHY_TXPWRADJ_CCK_PCDAC_INDEX_S 18
+
+#define AR_PHY_RADAR_EXT 0x9940
+#define AR_PHY_RADAR_EXT_ENA 0x00004000
+
+#define AR_PHY_RADAR_0 0x9954
+#define AR_PHY_RADAR_0_ENA 0x00000001
+#define AR_PHY_RADAR_0_FFT_ENA 0x80000000
+#define AR_PHY_RADAR_0_INBAND 0x0000003e
+#define AR_PHY_RADAR_0_INBAND_S 1
+#define AR_PHY_RADAR_0_PRSSI 0x00000FC0
+#define AR_PHY_RADAR_0_PRSSI_S 6
+#define AR_PHY_RADAR_0_HEIGHT 0x0003F000
+#define AR_PHY_RADAR_0_HEIGHT_S 12
+#define AR_PHY_RADAR_0_RRSSI 0x00FC0000
+#define AR_PHY_RADAR_0_RRSSI_S 18
+#define AR_PHY_RADAR_0_FIRPWR 0x7F000000
+#define AR_PHY_RADAR_0_FIRPWR_S 24
+
+#define AR_PHY_RADAR_1 0x9958
+#define AR_PHY_RADAR_1_RELPWR_ENA 0x00800000
+#define AR_PHY_RADAR_1_USE_FIR128 0x00400000
+#define AR_PHY_RADAR_1_RELPWR_THRESH 0x003F0000
+#define AR_PHY_RADAR_1_RELPWR_THRESH_S 16
+#define AR_PHY_RADAR_1_BLOCK_CHECK 0x00008000
+#define AR_PHY_RADAR_1_MAX_RRSSI 0x00004000
+#define AR_PHY_RADAR_1_RELSTEP_CHECK 0x00002000
+#define AR_PHY_RADAR_1_RELSTEP_THRESH 0x00001F00
+#define AR_PHY_RADAR_1_RELSTEP_THRESH_S 8
+#define AR_PHY_RADAR_1_MAXLEN 0x000000FF
+#define AR_PHY_RADAR_1_MAXLEN_S 0
+
+#define AR_PHY_SWITCH_CHAIN_0 0x9960
+#define AR_PHY_SWITCH_COM 0x9964
+
+#define AR_PHY_SIGMA_DELTA 0x996C
+#define AR_PHY_SIGMA_DELTA_ADC_SEL 0x00000003
+#define AR_PHY_SIGMA_DELTA_ADC_SEL_S 0
+#define AR_PHY_SIGMA_DELTA_FILT2 0x000000F8
+#define AR_PHY_SIGMA_DELTA_FILT2_S 3
+#define AR_PHY_SIGMA_DELTA_FILT1 0x00001F00
+#define AR_PHY_SIGMA_DELTA_FILT1_S 8
+#define AR_PHY_SIGMA_DELTA_ADC_CLIP 0x01FFE000
+#define AR_PHY_SIGMA_DELTA_ADC_CLIP_S 13
+
+#define AR_PHY_RESTART 0x9970
+#define AR_PHY_RESTART_DIV_GC 0x001C0000
+#define AR_PHY_RESTART_DIV_GC_S 18
+
+#define AR_PHY_RFBUS_REQ 0x997C
+#define AR_PHY_RFBUS_REQ_EN 0x00000001
+
+#define AR_PHY_TIMING7 0x9980
+#define AR_PHY_TIMING8 0x9984
+#define AR_PHY_TIMING8_PILOT_MASK_2 0x000FFFFF
+#define AR_PHY_TIMING8_PILOT_MASK_2_S 0
+
+#define AR_PHY_BIN_MASK2_1 0x9988
+#define AR_PHY_BIN_MASK2_2 0x998c
+#define AR_PHY_BIN_MASK2_3 0x9990
+#define AR_PHY_BIN_MASK2_4 0x9994
+
+#define AR_PHY_BIN_MASK_1 0x9900
+#define AR_PHY_BIN_MASK_2 0x9904
+#define AR_PHY_BIN_MASK_3 0x9908
+
+#define AR_PHY_MASK_CTL 0x990c
+
+#define AR_PHY_BIN_MASK2_4_MASK_4 0x00003FFF
+#define AR_PHY_BIN_MASK2_4_MASK_4_S 0
+
+#define AR_PHY_TIMING9 0x9998
+#define AR_PHY_TIMING10 0x999c
+#define AR_PHY_TIMING10_PILOT_MASK_2 0x000FFFFF
+#define AR_PHY_TIMING10_PILOT_MASK_2_S 0
+
+#define AR_PHY_TIMING11 0x99a0
+#define AR_PHY_TIMING11_SPUR_DELTA_PHASE 0x000FFFFF
+#define AR_PHY_TIMING11_SPUR_DELTA_PHASE_S 0
+#define AR_PHY_TIMING11_SPUR_FREQ_SD 0x3FF00000
+#define AR_PHY_TIMING11_SPUR_FREQ_SD_S 20
+#define AR_PHY_TIMING11_USE_SPUR_IN_AGC 0x40000000
+#define AR_PHY_TIMING11_USE_SPUR_IN_SELFCOR 0x80000000
+
+#define AR_PHY_RX_CHAINMASK 0x99a4
+#define AR_PHY_NEW_ADC_DC_GAIN_CORR(_i) (0x99b4 + ((_i) << 12))
+#define AR_PHY_NEW_ADC_GAIN_CORR_ENABLE 0x40000000
+#define AR_PHY_NEW_ADC_DC_OFFSET_CORR_ENABLE 0x80000000
+#define AR_PHY_MULTICHAIN_GAIN_CTL 0x99ac
+
+#define AR_PHY_EXT_CCA0 0x99b8
+#define AR_PHY_EXT_CCA0_THRESH62 0x000000FF
+#define AR_PHY_EXT_CCA0_THRESH62_S 0
+
+#define AR_PHY_EXT_CCA 0x99bc
+#define AR_PHY_EXT_CCA_CYCPWR_THR1 0x0000FE00
+#define AR_PHY_EXT_CCA_CYCPWR_THR1_S 9
+#define AR_PHY_EXT_CCA_THRESH62 0x007F0000
+#define AR_PHY_EXT_CCA_THRESH62_S 16
+#define AR_PHY_EXT_MINCCA_PWR 0xFF800000
+#define AR_PHY_EXT_MINCCA_PWR_S 23
+#define AR9280_PHY_EXT_MINCCA_PWR 0x01FF0000
+#define AR9280_PHY_EXT_MINCCA_PWR_S 16
+
+#define AR_PHY_SFCORR_EXT 0x99c0
+#define AR_PHY_SFCORR_EXT_M1_THRESH 0x0000007F
+#define AR_PHY_SFCORR_EXT_M1_THRESH_S 0
+#define AR_PHY_SFCORR_EXT_M2_THRESH 0x00003F80
+#define AR_PHY_SFCORR_EXT_M2_THRESH_S 7
+#define AR_PHY_SFCORR_EXT_M1_THRESH_LOW 0x001FC000
+#define AR_PHY_SFCORR_EXT_M1_THRESH_LOW_S 14
+#define AR_PHY_SFCORR_EXT_M2_THRESH_LOW 0x0FE00000
+#define AR_PHY_SFCORR_EXT_M2_THRESH_LOW_S 21
+#define AR_PHY_SFCORR_SPUR_SUBCHNL_SD_S 28
+
+#define AR_PHY_HALFGI 0x99D0
+#define AR_PHY_HALFGI_DSC_MAN 0x0007FFF0
+#define AR_PHY_HALFGI_DSC_MAN_S 4
+#define AR_PHY_HALFGI_DSC_EXP 0x0000000F
+#define AR_PHY_HALFGI_DSC_EXP_S 0
+
+#define AR_PHY_CHAN_INFO_MEMORY 0x99DC
+#define AR_PHY_CHAN_INFO_MEMORY_CAPTURE_MASK 0x0001
+
+#define AR_PHY_HEAVY_CLIP_ENABLE 0x99E0
+
+#define AR_PHY_M_SLEEP 0x99f0
+#define AR_PHY_REFCLKDLY 0x99f4
+#define AR_PHY_REFCLKPD 0x99f8
+
+#define AR_PHY_CALMODE 0x99f0
+
+#define AR_PHY_CALMODE_IQ 0x00000000
+#define AR_PHY_CALMODE_ADC_GAIN 0x00000001
+#define AR_PHY_CALMODE_ADC_DC_PER 0x00000002
+#define AR_PHY_CALMODE_ADC_DC_INIT 0x00000003
+
+#define AR_PHY_CAL_MEAS_0(_i) (0x9c10 + ((_i) << 12))
+#define AR_PHY_CAL_MEAS_1(_i) (0x9c14 + ((_i) << 12))
+#define AR_PHY_CAL_MEAS_2(_i) (0x9c18 + ((_i) << 12))
+#define AR_PHY_CAL_MEAS_3(_i) (0x9c1c + ((_i) << 12))
+
+#define AR_PHY_CURRENT_RSSI 0x9c1c
+#define AR9280_PHY_CURRENT_RSSI 0x9c3c
+
+#define AR_PHY_RFBUS_GRANT 0x9C20
+#define AR_PHY_RFBUS_GRANT_EN 0x00000001
+
+#define AR_PHY_CHAN_INFO_GAIN_DIFF 0x9CF4
+#define AR_PHY_CHAN_INFO_GAIN_DIFF_UPPER_LIMIT 320
+
+#define AR_PHY_CHAN_INFO_GAIN 0x9CFC
+
+#define AR_PHY_MODE 0xA200
+#define AR_PHY_MODE_AR2133 0x08
+#define AR_PHY_MODE_AR5111 0x00
+#define AR_PHY_MODE_AR5112 0x08
+#define AR_PHY_MODE_DYNAMIC 0x04
+#define AR_PHY_MODE_RF2GHZ 0x02
+#define AR_PHY_MODE_RF5GHZ 0x00
+#define AR_PHY_MODE_CCK 0x01
+#define AR_PHY_MODE_OFDM 0x00
+#define AR_PHY_MODE_DYN_CCK_DISABLE 0x100
+
+#define AR_PHY_CCK_TX_CTRL 0xA204
+#define AR_PHY_CCK_TX_CTRL_JAPAN 0x00000010
+
+#define AR_PHY_CCK_DETECT 0xA208
+#define AR_PHY_CCK_DETECT_WEAK_SIG_THR_CCK 0x0000003F
+#define AR_PHY_CCK_DETECT_WEAK_SIG_THR_CCK_S 0
+/* [12:6] settling time for antenna switch */
+#define AR_PHY_CCK_DETECT_ANT_SWITCH_TIME 0x00001FC0
+#define AR_PHY_CCK_DETECT_ANT_SWITCH_TIME_S 6
+#define AR_PHY_CCK_DETECT_BB_ENABLE_ANT_FAST_DIV 0x2000
+
+#define AR_PHY_GAIN_2GHZ 0xA20C
+#define AR_PHY_GAIN_2GHZ_RXTX_MARGIN 0x00FC0000
+#define AR_PHY_GAIN_2GHZ_RXTX_MARGIN_S 18
+#define AR_PHY_GAIN_2GHZ_BSW_MARGIN 0x00003C00
+#define AR_PHY_GAIN_2GHZ_BSW_MARGIN_S 10
+#define AR_PHY_GAIN_2GHZ_BSW_ATTEN 0x0000001F
+#define AR_PHY_GAIN_2GHZ_BSW_ATTEN_S 0
+
+#define AR_PHY_GAIN_2GHZ_XATTEN2_MARGIN 0x003E0000
+#define AR_PHY_GAIN_2GHZ_XATTEN2_MARGIN_S 17
+#define AR_PHY_GAIN_2GHZ_XATTEN1_MARGIN 0x0001F000
+#define AR_PHY_GAIN_2GHZ_XATTEN1_MARGIN_S 12
+#define AR_PHY_GAIN_2GHZ_XATTEN2_DB 0x00000FC0
+#define AR_PHY_GAIN_2GHZ_XATTEN2_DB_S 6
+#define AR_PHY_GAIN_2GHZ_XATTEN1_DB 0x0000003F
+#define AR_PHY_GAIN_2GHZ_XATTEN1_DB_S 0
+
+#define AR_PHY_CCK_RXCTRL4 0xA21C
+#define AR_PHY_CCK_RXCTRL4_FREQ_EST_SHORT 0x01F80000
+#define AR_PHY_CCK_RXCTRL4_FREQ_EST_SHORT_S 19
+
+#define AR_PHY_DAG_CTRLCCK 0xA228
+#define AR_PHY_DAG_CTRLCCK_EN_RSSI_THR 0x00000200
+#define AR_PHY_DAG_CTRLCCK_RSSI_THR 0x0001FC00
+#define AR_PHY_DAG_CTRLCCK_RSSI_THR_S 10
+
+#define AR_PHY_FORCE_CLKEN_CCK 0xA22C
+#define AR_PHY_FORCE_CLKEN_CCK_MRC_MUX 0x00000040
+
+#define AR_PHY_POWER_TX_RATE3 0xA234
+#define AR_PHY_POWER_TX_RATE4 0xA238
+
+#define AR_PHY_SCRM_SEQ_XR 0xA23C
+#define AR_PHY_HEADER_DETECT_XR 0xA240
+#define AR_PHY_CHIRP_DETECTED_XR 0xA244
+#define AR_PHY_BLUETOOTH 0xA254
+
+#define AR_PHY_TPCRG1 0xA258
+#define AR_PHY_TPCRG1_NUM_PD_GAIN 0x0000c000
+#define AR_PHY_TPCRG1_NUM_PD_GAIN_S 14
+
+#define AR_PHY_TPCRG1_PD_GAIN_1 0x00030000
+#define AR_PHY_TPCRG1_PD_GAIN_1_S 16
+#define AR_PHY_TPCRG1_PD_GAIN_2 0x000C0000
+#define AR_PHY_TPCRG1_PD_GAIN_2_S 18
+#define AR_PHY_TPCRG1_PD_GAIN_3 0x00300000
+#define AR_PHY_TPCRG1_PD_GAIN_3_S 20
+
+#define AR_PHY_VIT_MASK2_M_46_61 0xa3a0
+#define AR_PHY_MASK2_M_31_45 0xa3a4
+#define AR_PHY_MASK2_M_16_30 0xa3a8
+#define AR_PHY_MASK2_M_00_15 0xa3ac
+#define AR_PHY_MASK2_P_15_01 0xa3b8
+#define AR_PHY_MASK2_P_30_16 0xa3bc
+#define AR_PHY_MASK2_P_45_31 0xa3c0
+#define AR_PHY_MASK2_P_61_45 0xa3c4
+#define AR_PHY_SPUR_REG 0x994c
+
+#define AR_PHY_SPUR_REG_MASK_RATE_CNTL (0xFF << 18)
+#define AR_PHY_SPUR_REG_MASK_RATE_CNTL_S 18
+
+#define AR_PHY_SPUR_REG_ENABLE_MASK_PPM 0x20000
+#define AR_PHY_SPUR_REG_MASK_RATE_SELECT (0xFF << 9)
+#define AR_PHY_SPUR_REG_MASK_RATE_SELECT_S 9
+#define AR_PHY_SPUR_REG_ENABLE_VIT_SPUR_RSSI 0x100
+#define AR_PHY_SPUR_REG_SPUR_RSSI_THRESH 0x7F
+#define AR_PHY_SPUR_REG_SPUR_RSSI_THRESH_S 0
+
+#define AR_PHY_PILOT_MASK_01_30 0xa3b0
+#define AR_PHY_PILOT_MASK_31_60 0xa3b4
+
+#define AR_PHY_CHANNEL_MASK_01_30 0x99d4
+#define AR_PHY_CHANNEL_MASK_31_60 0x99d8
+
+#define AR_PHY_ANALOG_SWAP 0xa268
+#define AR_PHY_SWAP_ALT_CHAIN 0x00000040
+
+#define AR_PHY_TPCRG5 0xA26C
+#define AR_PHY_TPCRG5_PD_GAIN_OVERLAP 0x0000000F
+#define AR_PHY_TPCRG5_PD_GAIN_OVERLAP_S 0
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_1 0x000003F0
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_1_S 4
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_2 0x0000FC00
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_2_S 10
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_3 0x003F0000
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_3_S 16
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_4 0x0FC00000
+#define AR_PHY_TPCRG5_PD_GAIN_BOUNDARY_4_S 22
+
+#define AR_PHY_POWER_TX_RATE5 0xA38C
+#define AR_PHY_POWER_TX_RATE6 0xA390
+
+#define AR_PHY_CAL_CHAINMASK 0xA39C
+
+#define AR_PHY_POWER_TX_SUB 0xA3C8
+#define AR_PHY_POWER_TX_RATE7 0xA3CC
+#define AR_PHY_POWER_TX_RATE8 0xA3D0
+#define AR_PHY_POWER_TX_RATE9 0xA3D4
+
+#define AR_PHY_XPA_CFG 0xA3D8
+#define AR_PHY_FORCE_XPA_CFG 0x000000001
+#define AR_PHY_FORCE_XPA_CFG_S 0
+
+#define AR_PHY_CH1_CCA 0xa864
+#define AR_PHY_CH1_MINCCA_PWR 0x0FF80000
+#define AR_PHY_CH1_MINCCA_PWR_S 19
+#define AR9280_PHY_CH1_MINCCA_PWR 0x1FF00000
+#define AR9280_PHY_CH1_MINCCA_PWR_S 20
+
+#define AR_PHY_CH2_CCA 0xb864
+#define AR_PHY_CH2_MINCCA_PWR 0x0FF80000
+#define AR_PHY_CH2_MINCCA_PWR_S 19
+
+#define AR_PHY_CH1_EXT_CCA 0xa9bc
+#define AR_PHY_CH1_EXT_MINCCA_PWR 0xFF800000
+#define AR_PHY_CH1_EXT_MINCCA_PWR_S 23
+#define AR9280_PHY_CH1_EXT_MINCCA_PWR 0x01FF0000
+#define AR9280_PHY_CH1_EXT_MINCCA_PWR_S 16
+
+#define AR_PHY_CH2_EXT_CCA 0xb9bc
+#define AR_PHY_CH2_EXT_MINCCA_PWR 0xFF800000
+#define AR_PHY_CH2_EXT_MINCCA_PWR_S 23
+
+#define REG_WRITE_RF_ARRAY(iniarray, regData, regWr) do { \
+ int r; \
+ for (r = 0; r < ((iniarray)->ia_rows); r++) { \
+ REG_WRITE(ah, INI_RA((iniarray), r, 0), (regData)[r]); \
+ DPRINTF(ah->ah_sc, ATH_DBG_CHANNEL, \
+ "RF 0x%x V 0x%x\n", \
+ INI_RA((iniarray), r, 0), (regData)[r]); \
+ DO_DELAY(regWr); \
+ } \
+ } while (0)
+
+#define ATH9K_KEY_XOR 0xaa
+
+#define ATH9K_IS_MIC_ENABLED(ah) \
+ (AH5416(ah)->ah_staId1Defaults & AR_STA_ID1_CRPT_MIC_ENABLE)
+
+#define ANTSWAP_AB 0x0001
+#define REDUCE_CHAIN_0 0x00000050
+#define REDUCE_CHAIN_1 0x00000051
+
+#define RF_BANK_SETUP(_bank, _iniarray, _col) do { \
+ int i; \
+ for (i = 0; i < (_iniarray)->ia_rows; i++) \
+ (_bank)[i] = INI_RA((_iniarray), i, _col);; \
+ } while (0)
+
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2004 Video54 Technologies, Inc.
+ * Copyright (c) 2004-2008 Atheros Communications, Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*
+ * Atheros rate control algorithm
+ */
+
+#include "core.h"
+#include "../net/mac80211/rate.h"
+
+static u32 tx_triglevel_max;
+
+static struct ath_rate_table ar5416_11na_ratetable = {
+ 42,
+ {
+ { TRUE, TRUE, WLAN_PHY_OFDM, 6000, /* 6 Mb */
+ 5400, 0x0b, 0x00, 12,
+ 0, 2, 1, 0, 0, 0, 0, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 9000, /* 9 Mb */
+ 7800, 0x0f, 0x00, 18,
+ 0, 3, 1, 1, 1, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 12 Mb */
+ 10000, 0x0a, 0x00, 24,
+ 2, 4, 2, 2, 2, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 18000, /* 18 Mb */
+ 13900, 0x0e, 0x00, 36,
+ 2, 6, 2, 3, 3, 3, 3, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 24000, /* 24 Mb */
+ 17300, 0x09, 0x00, 48,
+ 4, 10, 3, 4, 4, 4, 4, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 36000, /* 36 Mb */
+ 23000, 0x0d, 0x00, 72,
+ 4, 14, 3, 5, 5, 5, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 48000, /* 48 Mb */
+ 27400, 0x08, 0x00, 96,
+ 4, 20, 3, 6, 6, 6, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 54000, /* 54 Mb */
+ 29300, 0x0c, 0x00, 108,
+ 4, 23, 3, 7, 7, 7, 7, 0 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 6500, /* 6.5 Mb */
+ 6400, 0x80, 0x00, 0,
+ 0, 2, 3, 8, 24, 8, 24, 3216 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 13000, /* 13 Mb */
+ 12700, 0x81, 0x00, 1,
+ 2, 4, 3, 9, 25, 9, 25, 6434 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 19500, /* 19.5 Mb */
+ 18800, 0x82, 0x00, 2,
+ 2, 6, 3, 10, 26, 10, 26, 9650 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 26000, /* 26 Mb */
+ 25000, 0x83, 0x00, 3,
+ 4, 10, 3, 11, 27, 11, 27, 12868 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 39000, /* 39 Mb */
+ 36700, 0x84, 0x00, 4,
+ 4, 14, 3, 12, 28, 12, 28, 19304 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 52000, /* 52 Mb */
+ 48100, 0x85, 0x00, 5,
+ 4, 20, 3, 13, 29, 13, 29, 25740 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 58500, /* 58.5 Mb */
+ 53500, 0x86, 0x00, 6,
+ 4, 23, 3, 14, 30, 14, 30, 28956 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 65000, /* 65 Mb */
+ 59000, 0x87, 0x00, 7,
+ 4, 25, 3, 15, 31, 15, 32, 32180 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 13000, /* 13 Mb */
+ 12700, 0x88, 0x00,
+ 8, 0, 2, 3, 16, 33, 16, 33, 6430 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 26000, /* 26 Mb */
+ 24800, 0x89, 0x00, 9,
+ 2, 4, 3, 17, 34, 17, 34, 12860 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 39000, /* 39 Mb */
+ 36600, 0x8a, 0x00, 10,
+ 2, 6, 3, 18, 35, 18, 35, 19300 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 52000, /* 52 Mb */
+ 48100, 0x8b, 0x00, 11,
+ 4, 10, 3, 19, 36, 19, 36, 25736 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 78000, /* 78 Mb */
+ 69500, 0x8c, 0x00, 12,
+ 4, 14, 3, 20, 37, 20, 37, 38600 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 104000, /* 104 Mb */
+ 89500, 0x8d, 0x00, 13,
+ 4, 20, 3, 21, 38, 21, 38, 51472 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 117000, /* 117 Mb */
+ 98900, 0x8e, 0x00, 14,
+ 4, 23, 3, 22, 39, 22, 39, 57890 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 130000, /* 130 Mb */
+ 108300, 0x8f, 0x00, 15,
+ 4, 25, 3, 23, 40, 23, 41, 64320 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 13500, /* 13.5 Mb */
+ 13200, 0x80, 0x00, 0,
+ 0, 2, 3, 8, 24, 24, 24, 6684 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 27500, /* 27.0 Mb */
+ 25900, 0x81, 0x00, 1,
+ 2, 4, 3, 9, 25, 25, 25, 13368 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 40500, /* 40.5 Mb */
+ 38600, 0x82, 0x00, 2,
+ 2, 6, 3, 10, 26, 26, 26, 20052 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 54000, /* 54 Mb */
+ 49800, 0x83, 0x00, 3,
+ 4, 10, 3, 11, 27, 27, 27, 26738 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 81500, /* 81 Mb */
+ 72200, 0x84, 0x00, 4,
+ 4, 14, 3, 12, 28, 28, 28, 40104 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 108000, /* 108 Mb */
+ 92900, 0x85, 0x00, 5,
+ 4, 20, 3, 13, 29, 29, 29, 53476 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 121500, /* 121.5 Mb */
+ 102700, 0x86, 0x00, 6,
+ 4, 23, 3, 14, 30, 30, 30, 60156 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 135000, /* 135 Mb */
+ 112000, 0x87, 0x00, 7,
+ 4, 25, 3, 15, 31, 32, 32, 66840 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS_HGI, 150000, /* 150 Mb */
+ 122000, 0x87, 0x00, 7,
+ 4, 25, 3, 15, 31, 32, 32, 74200 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 27000, /* 27 Mb */
+ 25800, 0x88, 0x00, 8,
+ 0, 2, 3, 16, 33, 33, 33, 13360 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 54000, /* 54 Mb */
+ 49800, 0x89, 0x00, 9,
+ 2, 4, 3, 17, 34, 34, 34, 26720 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 81000, /* 81 Mb */
+ 71900, 0x8a, 0x00, 10,
+ 2, 6, 3, 18, 35, 35, 35, 40080 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 108000, /* 108 Mb */
+ 92500, 0x8b, 0x00, 11,
+ 4, 10, 3, 19, 36, 36, 36, 53440 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 162000, /* 162 Mb */
+ 130300, 0x8c, 0x00, 12,
+ 4, 14, 3, 20, 37, 37, 37, 80160 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 216000, /* 216 Mb */
+ 162800, 0x8d, 0x00, 13,
+ 4, 20, 3, 21, 38, 38, 38, 106880 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 243000, /* 243 Mb */
+ 178200, 0x8e, 0x00, 14,
+ 4, 23, 3, 22, 39, 39, 39, 120240 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 270000, /* 270 Mb */
+ 192100, 0x8f, 0x00, 15,
+ 4, 25, 3, 23, 40, 41, 41, 133600 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS_HGI, 300000, /* 300 Mb */
+ 207000, 0x8f, 0x00, 15,
+ 4, 25, 3, 23, 40, 41, 41, 148400 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ WLAN_RC_HT_FLAG, /* Phy rates allowed initially */
+};
+
+/* TRUE_ALL - valid for 20/40/Legacy,
+ * TRUE - Legacy only,
+ * TRUE_20 - HT 20 only,
+ * TRUE_40 - HT 40 only */
+
+/* 4ms frame limit not used for NG mode. The values filled
+ * for HT are the 64K max aggregate limit */
+
+static struct ath_rate_table ar5416_11ng_ratetable = {
+ 46,
+ {
+ { TRUE_ALL, TRUE_ALL, WLAN_PHY_CCK, 1000, /* 1 Mb */
+ 900, 0x1b, 0x00, 2,
+ 0, 0, 1, 0, 0, 0, 0, 0 },
+ { TRUE_ALL, TRUE_ALL, WLAN_PHY_CCK, 2000, /* 2 Mb */
+ 1900, 0x1a, 0x04, 4,
+ 1, 1, 1, 1, 1, 1, 1, 0 },
+ { TRUE_ALL, TRUE_ALL, WLAN_PHY_CCK, 5500, /* 5.5 Mb */
+ 4900, 0x19, 0x04, 11,
+ 2, 2, 2, 2, 2, 2, 2, 0 },
+ { TRUE_ALL, TRUE_ALL, WLAN_PHY_CCK, 11000, /* 11 Mb */
+ 8100, 0x18, 0x04, 22,
+ 3, 3, 2, 3, 3, 3, 3, 0 },
+ { FALSE, FALSE, WLAN_PHY_OFDM, 6000, /* 6 Mb */
+ 5400, 0x0b, 0x00, 12,
+ 4, 2, 1, 4, 4, 4, 4, 0 },
+ { FALSE, FALSE, WLAN_PHY_OFDM, 9000, /* 9 Mb */
+ 7800, 0x0f, 0x00, 18,
+ 4, 3, 1, 5, 5, 5, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 12 Mb */
+ 10100, 0x0a, 0x00, 24,
+ 6, 4, 1, 6, 6, 6, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 18000, /* 18 Mb */
+ 14100, 0x0e, 0x00, 36,
+ 6, 6, 2, 7, 7, 7, 7, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 24000, /* 24 Mb */
+ 17700, 0x09, 0x00, 48,
+ 8, 10, 3, 8, 8, 8, 8, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 36000, /* 36 Mb */
+ 23700, 0x0d, 0x00, 72,
+ 8, 14, 3, 9, 9, 9, 9, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 48000, /* 48 Mb */
+ 27400, 0x08, 0x00, 96,
+ 8, 20, 3, 10, 10, 10, 10, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 54000, /* 54 Mb */
+ 30900, 0x0c, 0x00, 108,
+ 8, 23, 3, 11, 11, 11, 11, 0 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_SS, 6500, /* 6.5 Mb */
+ 6400, 0x80, 0x00, 0,
+ 4, 2, 3, 12, 28, 12, 28, 3216 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 13000, /* 13 Mb */
+ 12700, 0x81, 0x00, 1,
+ 6, 4, 3, 13, 29, 13, 29, 6434 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 19500, /* 19.5 Mb */
+ 18800, 0x82, 0x00, 2,
+ 6, 6, 3, 14, 30, 14, 30, 9650 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 26000, /* 26 Mb */
+ 25000, 0x83, 0x00, 3,
+ 8, 10, 3, 15, 31, 15, 31, 12868 },
+ { TRUE_20, TRUE_20, WLAN_PHY_HT_20_SS, 39000, /* 39 Mb */
+ 36700, 0x84, 0x00, 4,
+ 8, 14, 3, 16, 32, 16, 32, 19304 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 52000, /* 52 Mb */
+ 48100, 0x85, 0x00, 5,
+ 8, 20, 3, 17, 33, 17, 33, 25740 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 58500, /* 58.5 Mb */
+ 53500, 0x86, 0x00, 6,
+ 8, 23, 3, 18, 34, 18, 34, 28956 },
+ { FALSE, TRUE_20, WLAN_PHY_HT_20_SS, 65000, /* 65 Mb */
+ 59000, 0x87, 0x00, 7,
+ 8, 25, 3, 19, 35, 19, 36, 32180 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 13000, /* 13 Mb */
+ 12700, 0x88, 0x00, 8,
+ 4, 2, 3, 20, 37, 20, 37, 6430 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 26000, /* 26 Mb */
+ 24800, 0x89, 0x00, 9,
+ 6, 4, 3, 21, 38, 21, 38, 12860 },
+ { FALSE, FALSE, WLAN_PHY_HT_20_DS, 39000, /* 39 Mb */
+ 36600, 0x8a, 0x00, 10,
+ 6, 6, 3, 22, 39, 22, 39, 19300 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 52000, /* 52 Mb */
+ 48100, 0x8b, 0x00, 11,
+ 8, 10, 3, 23, 40, 23, 40, 25736 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 78000, /* 78 Mb */
+ 69500, 0x8c, 0x00, 12,
+ 8, 14, 3, 24, 41, 24, 41, 38600 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 104000, /* 104 Mb */
+ 89500, 0x8d, 0x00, 13,
+ 8, 20, 3, 25, 42, 25, 42, 51472 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 117000, /* 117 Mb */
+ 98900, 0x8e, 0x00, 14,
+ 8, 23, 3, 26, 43, 26, 44, 57890 },
+ { TRUE_20, FALSE, WLAN_PHY_HT_20_DS, 130000, /* 130 Mb */
+ 108300, 0x8f, 0x00, 15,
+ 8, 25, 3, 27, 44, 27, 45, 64320 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 13500, /* 13.5 Mb */
+ 13200, 0x80, 0x00, 0,
+ 8, 2, 3, 12, 28, 28, 28, 6684 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 27500, /* 27.0 Mb */
+ 25900, 0x81, 0x00, 1,
+ 8, 4, 3, 13, 29, 29, 29, 13368 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 40500, /* 40.5 Mb */
+ 38600, 0x82, 0x00, 2,
+ 8, 6, 3, 14, 30, 30, 30, 20052 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 54000, /* 54 Mb */
+ 49800, 0x83, 0x00, 3,
+ 8, 10, 3, 15, 31, 31, 31, 26738 },
+ { TRUE_40, TRUE_40, WLAN_PHY_HT_40_SS, 81500, /* 81 Mb */
+ 72200, 0x84, 0x00, 4,
+ 8, 14, 3, 16, 32, 32, 32, 40104 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 108000, /* 108 Mb */
+ 92900, 0x85, 0x00, 5,
+ 8, 20, 3, 17, 33, 33, 33, 53476 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 121500, /* 121.5 Mb */
+ 102700, 0x86, 0x00, 6,
+ 8, 23, 3, 18, 34, 34, 34, 60156 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS, 135000, /* 135 Mb */
+ 112000, 0x87, 0x00, 7,
+ 8, 23, 3, 19, 35, 36, 36, 66840 },
+ { FALSE, TRUE_40, WLAN_PHY_HT_40_SS_HGI, 150000, /* 150 Mb */
+ 122000, 0x87, 0x00, 7,
+ 8, 25, 3, 19, 35, 36, 36, 74200 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 27000, /* 27 Mb */
+ 25800, 0x88, 0x00, 8,
+ 8, 2, 3, 20, 37, 37, 37, 13360 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 54000, /* 54 Mb */
+ 49800, 0x89, 0x00, 9,
+ 8, 4, 3, 21, 38, 38, 38, 26720 },
+ { FALSE, FALSE, WLAN_PHY_HT_40_DS, 81000, /* 81 Mb */
+ 71900, 0x8a, 0x00, 10,
+ 8, 6, 3, 22, 39, 39, 39, 40080 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 108000, /* 108 Mb */
+ 92500, 0x8b, 0x00, 11,
+ 8, 10, 3, 23, 40, 40, 40, 53440 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 162000, /* 162 Mb */
+ 130300, 0x8c, 0x00, 12,
+ 8, 14, 3, 24, 41, 41, 41, 80160 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 216000, /* 216 Mb */
+ 162800, 0x8d, 0x00, 13,
+ 8, 20, 3, 25, 42, 42, 42, 106880 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 243000, /* 243 Mb */
+ 178200, 0x8e, 0x00, 14,
+ 8, 23, 3, 26, 43, 43, 43, 120240 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS, 270000, /* 270 Mb */
+ 192100, 0x8f, 0x00, 15,
+ 8, 23, 3, 27, 44, 45, 45, 133600 },
+ { TRUE_40, FALSE, WLAN_PHY_HT_40_DS_HGI, 300000, /* 300 Mb */
+ 207000, 0x8f, 0x00, 15,
+ 8, 25, 3, 27, 44, 45, 45, 148400 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ WLAN_RC_HT_FLAG, /* Phy rates allowed initially */
+};
+
+static struct ath_rate_table ar5416_11a_ratetable = {
+ 8,
+ {
+ { TRUE, TRUE, WLAN_PHY_OFDM, 6000, /* 6 Mb */
+ 5400, 0x0b, 0x00, (0x80|12),
+ 0, 2, 1, 0, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 9000, /* 9 Mb */
+ 7800, 0x0f, 0x00, 18,
+ 0, 3, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 12 Mb */
+ 10000, 0x0a, 0x00, (0x80|24),
+ 2, 4, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 18000, /* 18 Mb */
+ 13900, 0x0e, 0x00, 36,
+ 2, 6, 2, 3, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 24000, /* 24 Mb */
+ 17300, 0x09, 0x00, (0x80|48),
+ 4, 10, 3, 4, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 36000, /* 36 Mb */
+ 23000, 0x0d, 0x00, 72,
+ 4, 14, 3, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 48000, /* 48 Mb */
+ 27400, 0x08, 0x00, 96,
+ 4, 19, 3, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 54000, /* 54 Mb */
+ 29300, 0x0c, 0x00, 108,
+ 4, 23, 3, 7, 0 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ 0, /* Phy rates allowed initially */
+};
+
+static struct ath_rate_table ar5416_11a_ratetable_Half = {
+ 8,
+ {
+ { TRUE, TRUE, WLAN_PHY_OFDM, 3000, /* 6 Mb */
+ 2700, 0x0b, 0x00, (0x80|6),
+ 0, 2, 1, 0, 0},
+ { TRUE, TRUE, WLAN_PHY_OFDM, 4500, /* 9 Mb */
+ 3900, 0x0f, 0x00, 9,
+ 0, 3, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 6000, /* 12 Mb */
+ 5000, 0x0a, 0x00, (0x80|12),
+ 2, 4, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 9000, /* 18 Mb */
+ 6950, 0x0e, 0x00, 18,
+ 2, 6, 2, 3, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 24 Mb */
+ 8650, 0x09, 0x00, (0x80|24),
+ 4, 10, 3, 4, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 18000, /* 36 Mb */
+ 11500, 0x0d, 0x00, 36,
+ 4, 14, 3, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 24000, /* 48 Mb */
+ 13700, 0x08, 0x00, 48,
+ 4, 19, 3, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 27000, /* 54 Mb */
+ 14650, 0x0c, 0x00, 54,
+ 4, 23, 3, 7, 0 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ 0, /* Phy rates allowed initially */
+};
+
+static struct ath_rate_table ar5416_11a_ratetable_Quarter = {
+ 8,
+ {
+ { TRUE, TRUE, WLAN_PHY_OFDM, 1500, /* 6 Mb */
+ 1350, 0x0b, 0x00, (0x80|3),
+ 0, 2, 1, 0, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 2250, /* 9 Mb */
+ 1950, 0x0f, 0x00, 4,
+ 0, 3, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 3000, /* 12 Mb */
+ 2500, 0x0a, 0x00, (0x80|6),
+ 2, 4, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 4500, /* 18 Mb */
+ 3475, 0x0e, 0x00, 9,
+ 2, 6, 2, 3, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 6000, /* 25 Mb */
+ 4325, 0x09, 0x00, (0x80|12),
+ 4, 10, 3, 4, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 9000, /* 36 Mb */
+ 5750, 0x0d, 0x00, 18,
+ 4, 14, 3, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 48 Mb */
+ 6850, 0x08, 0x00, 24,
+ 4, 19, 3, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 13500, /* 54 Mb */
+ 7325, 0x0c, 0x00, 27,
+ 4, 23, 3, 7, 0 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ 0, /* Phy rates allowed initially */
+};
+
+static struct ath_rate_table ar5416_11g_ratetable = {
+ 12,
+ {
+ { TRUE, TRUE, WLAN_PHY_CCK, 1000, /* 1 Mb */
+ 900, 0x1b, 0x00, 2,
+ 0, 0, 1, 0, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 2000, /* 2 Mb */
+ 1900, 0x1a, 0x04, 4,
+ 1, 1, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 5500, /* 5.5 Mb */
+ 4900, 0x19, 0x04, 11,
+ 2, 2, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 11000, /* 11 Mb */
+ 8100, 0x18, 0x04, 22,
+ 3, 3, 2, 3, 0 },
+ { FALSE, FALSE, WLAN_PHY_OFDM, 6000, /* 6 Mb */
+ 5400, 0x0b, 0x00, 12,
+ 4, 2, 1, 4, 0 },
+ { FALSE, FALSE, WLAN_PHY_OFDM, 9000, /* 9 Mb */
+ 7800, 0x0f, 0x00, 18,
+ 4, 3, 1, 5, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 12000, /* 12 Mb */
+ 10000, 0x0a, 0x00, 24,
+ 6, 4, 1, 6, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 18000, /* 18 Mb */
+ 13900, 0x0e, 0x00, 36,
+ 6, 6, 2, 7, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 24000, /* 24 Mb */
+ 17300, 0x09, 0x00, 48,
+ 8, 10, 3, 8, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 36000, /* 36 Mb */
+ 23000, 0x0d, 0x00, 72,
+ 8, 14, 3, 9, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 48000, /* 48 Mb */
+ 27400, 0x08, 0x00, 96,
+ 8, 19, 3, 10, 0 },
+ { TRUE, TRUE, WLAN_PHY_OFDM, 54000, /* 54 Mb */
+ 29300, 0x0c, 0x00, 108,
+ 8, 23, 3, 11, 0 },
+ },
+ 50, /* probe interval */
+ 50, /* rssi reduce interval */
+ 0, /* Phy rates allowed initially */
+};
+
+static struct ath_rate_table ar5416_11b_ratetable = {
+ 4,
+ {
+ { TRUE, TRUE, WLAN_PHY_CCK, 1000, /* 1 Mb */
+ 900, 0x1b, 0x00, (0x80|2),
+ 0, 0, 1, 0, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 2000, /* 2 Mb */
+ 1800, 0x1a, 0x04, (0x80|4),
+ 1, 1, 1, 1, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 5500, /* 5.5 Mb */
+ 4300, 0x19, 0x04, (0x80|11),
+ 1, 2, 2, 2, 0 },
+ { TRUE, TRUE, WLAN_PHY_CCK, 11000, /* 11 Mb */
+ 7100, 0x18, 0x04, (0x80|22),
+ 1, 4, 100, 3, 0 },
+ },
+ 100, /* probe interval */
+ 100, /* rssi reduce interval */
+ 0, /* Phy rates allowed initially */
+};
+
+static void ar5416_attach_ratetables(struct ath_rate_softc *sc)
+{
+ /*
+ * Attach rate tables.
+ */
+ sc->hw_rate_table[ATH9K_MODE_11B] = &ar5416_11b_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11A] = &ar5416_11a_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11G] = &ar5416_11g_ratetable;
+
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT20] = &ar5416_11na_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT20] = &ar5416_11ng_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT40PLUS] =
+ &ar5416_11na_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT40MINUS] =
+ &ar5416_11na_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT40PLUS] =
+ &ar5416_11ng_ratetable;
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT40MINUS] =
+ &ar5416_11ng_ratetable;
+}
+
+static void ar5416_setquarter_ratetable(struct ath_rate_softc *sc)
+{
+ sc->hw_rate_table[ATH9K_MODE_11A] = &ar5416_11a_ratetable_Quarter;
+ return;
+}
+
+static void ar5416_sethalf_ratetable(struct ath_rate_softc *sc)
+{
+ sc->hw_rate_table[ATH9K_MODE_11A] = &ar5416_11a_ratetable_Half;
+ return;
+}
+
+static void ar5416_setfull_ratetable(struct ath_rate_softc *sc)
+{
+ sc->hw_rate_table[ATH9K_MODE_11A] = &ar5416_11a_ratetable;
+ return;
+}
+
+/*
+ * Return the median of three numbers
+ */
+static inline int8_t median(int8_t a, int8_t b, int8_t c)
+{
+ if (a >= b) {
+ if (b >= c)
+ return b;
+ else if (a > c)
+ return c;
+ else
+ return a;
+ } else {
+ if (a >= c)
+ return a;
+ else if (b >= c)
+ return c;
+ else
+ return b;
+ }
+}
+
+static void ath_rc_sort_validrates(const struct ath_rate_table *rate_table,
+ struct ath_tx_ratectrl *rate_ctrl)
+{
+ u8 i, j, idx, idx_next;
+
+ for (i = rate_ctrl->max_valid_rate - 1; i > 0; i--) {
+ for (j = 0; j <= i-1; j++) {
+ idx = rate_ctrl->valid_rate_index[j];
+ idx_next = rate_ctrl->valid_rate_index[j+1];
+
+ if (rate_table->info[idx].ratekbps >
+ rate_table->info[idx_next].ratekbps) {
+ rate_ctrl->valid_rate_index[j] = idx_next;
+ rate_ctrl->valid_rate_index[j+1] = idx;
+ }
+ }
+ }
+}
+
+/* Access functions for valid_txrate_mask */
+
+static void ath_rc_init_valid_txmask(struct ath_tx_ratectrl *rate_ctrl)
+{
+ u8 i;
+
+ for (i = 0; i < rate_ctrl->rate_table_size; i++)
+ rate_ctrl->valid_rate_index[i] = FALSE;
+}
+
+static inline void ath_rc_set_valid_txmask(struct ath_tx_ratectrl *rate_ctrl,
+ u8 index, int valid_tx_rate)
+{
+ ASSERT(index <= rate_ctrl->rate_table_size);
+ rate_ctrl->valid_rate_index[index] = valid_tx_rate ? TRUE : FALSE;
+}
+
+static inline int ath_rc_isvalid_txmask(struct ath_tx_ratectrl *rate_ctrl,
+ u8 index)
+{
+ ASSERT(index <= rate_ctrl->rate_table_size);
+ return rate_ctrl->valid_rate_index[index];
+}
+
+/* Iterators for valid_txrate_mask */
+static inline int
+ath_rc_get_nextvalid_txrate(const struct ath_rate_table *rate_table,
+ struct ath_tx_ratectrl *rate_ctrl,
+ u8 cur_valid_txrate,
+ u8 *next_idx)
+{
+ u8 i;
+
+ for (i = 0; i < rate_ctrl->max_valid_rate - 1; i++) {
+ if (rate_ctrl->valid_rate_index[i] == cur_valid_txrate) {
+ *next_idx = rate_ctrl->valid_rate_index[i+1];
+ return TRUE;
+ }
+ }
+
+ /* No more valid rates */
+ *next_idx = 0;
+ return FALSE;
+}
+
+/* Return true only for single stream */
+
+static int ath_rc_valid_phyrate(u32 phy, u32 capflag, int ignore_cw)
+{
+ if (WLAN_RC_PHY_HT(phy) & !(capflag & WLAN_RC_HT_FLAG))
+ return FALSE;
+ if (WLAN_RC_PHY_DS(phy) && !(capflag & WLAN_RC_DS_FLAG))
+ return FALSE;
+ if (WLAN_RC_PHY_SGI(phy) && !(capflag & WLAN_RC_SGI_FLAG))
+ return FALSE;
+ if (!ignore_cw && WLAN_RC_PHY_HT(phy))
+ if (WLAN_RC_PHY_40(phy) && !(capflag & WLAN_RC_40_FLAG))
+ return FALSE;
+ if (!WLAN_RC_PHY_40(phy) && (capflag & WLAN_RC_40_FLAG))
+ return FALSE;
+ return TRUE;
+}
+
+static inline int
+ath_rc_get_nextlowervalid_txrate(const struct ath_rate_table *rate_table,
+ struct ath_tx_ratectrl *rate_ctrl,
+ u8 cur_valid_txrate, u8 *next_idx)
+{
+ int8_t i;
+
+ for (i = 1; i < rate_ctrl->max_valid_rate ; i++) {
+ if (rate_ctrl->valid_rate_index[i] == cur_valid_txrate) {
+ *next_idx = rate_ctrl->valid_rate_index[i-1];
+ return TRUE;
+ }
+ }
+ return FALSE;
+}
+
+/*
+ * Initialize the Valid Rate Index from valid entries in Rate Table
+ */
+static u8
+ath_rc_sib_init_validrates(struct ath_rate_node *ath_rc_priv,
+ const struct ath_rate_table *rate_table,
+ u32 capflag)
+{
+ struct ath_tx_ratectrl *rate_ctrl;
+ u8 i, hi = 0;
+ u32 valid;
+
+ rate_ctrl = (struct ath_tx_ratectrl *)(ath_rc_priv);
+ for (i = 0; i < rate_table->rate_cnt; i++) {
+ valid = (ath_rc_priv->single_stream ?
+ rate_table->info[i].valid_single_stream :
+ rate_table->info[i].valid);
+ if (valid == TRUE) {
+ u32 phy = rate_table->info[i].phy;
+ u8 valid_rate_count = 0;
+
+ if (!ath_rc_valid_phyrate(phy, capflag, FALSE))
+ continue;
+
+ valid_rate_count = rate_ctrl->valid_phy_ratecnt[phy];
+
+ rate_ctrl->valid_phy_rateidx[phy][valid_rate_count] = i;
+ rate_ctrl->valid_phy_ratecnt[phy] += 1;
+ ath_rc_set_valid_txmask(rate_ctrl, i, TRUE);
+ hi = A_MAX(hi, i);
+ }
+ }
+ return hi;
+}
+
+/*
+ * Initialize the Valid Rate Index from Rate Set
+ */
+static u8
+ath_rc_sib_setvalid_rates(struct ath_rate_node *ath_rc_priv,
+ const struct ath_rate_table *rate_table,
+ struct ath_rateset *rateset,
+ u32 capflag)
+{
+ /* XXX: Clean me up and make identation friendly */
+ u8 i, j, hi = 0;
+ struct ath_tx_ratectrl *rate_ctrl =
+ (struct ath_tx_ratectrl *)(ath_rc_priv);
+
+ /* Use intersection of working rates and valid rates */
+ for (i = 0; i < rateset->rs_nrates; i++) {
+ for (j = 0; j < rate_table->rate_cnt; j++) {
+ u32 phy = rate_table->info[j].phy;
+ u32 valid = (ath_rc_priv->single_stream ?
+ rate_table->info[j].valid_single_stream :
+ rate_table->info[j].valid);
+
+ /* We allow a rate only if its valid and the
+ * capflag matches one of the validity
+ * (TRUE/TRUE_20/TRUE_40) flags */
+
+ /* XXX: catch the negative of this branch
+ * first and then continue */
+ if (((rateset->rs_rates[i] & 0x7F) ==
+ (rate_table->info[j].dot11rate & 0x7F)) &&
+ ((valid & WLAN_RC_CAP_MODE(capflag)) ==
+ WLAN_RC_CAP_MODE(capflag)) &&
+ !WLAN_RC_PHY_HT(phy)) {
+
+ u8 valid_rate_count = 0;
+
+ if (!ath_rc_valid_phyrate(phy, capflag, FALSE))
+ continue;
+
+ valid_rate_count =
+ rate_ctrl->valid_phy_ratecnt[phy];
+
+ rate_ctrl->valid_phy_rateidx[phy]
+ [valid_rate_count] = j;
+ rate_ctrl->valid_phy_ratecnt[phy] += 1;
+ ath_rc_set_valid_txmask(rate_ctrl, j, TRUE);
+ hi = A_MAX(hi, j);
+ }
+ }
+ }
+ return hi;
+}
+
+static u8
+ath_rc_sib_setvalid_htrates(struct ath_rate_node *ath_rc_priv,
+ const struct ath_rate_table *rate_table,
+ u8 *mcs_set, u32 capflag)
+{
+ u8 i, j, hi = 0;
+ struct ath_tx_ratectrl *rate_ctrl =
+ (struct ath_tx_ratectrl *)(ath_rc_priv);
+
+ /* Use intersection of working rates and valid rates */
+ for (i = 0; i < ((struct ath_rateset *)mcs_set)->rs_nrates; i++) {
+ for (j = 0; j < rate_table->rate_cnt; j++) {
+ u32 phy = rate_table->info[j].phy;
+ u32 valid = (ath_rc_priv->single_stream ?
+ rate_table->info[j].valid_single_stream :
+ rate_table->info[j].valid);
+
+ if (((((struct ath_rateset *)
+ mcs_set)->rs_rates[i] & 0x7F) !=
+ (rate_table->info[j].dot11rate & 0x7F)) ||
+ !WLAN_RC_PHY_HT(phy) ||
+ !WLAN_RC_PHY_HT_VALID(valid, capflag))
+ continue;
+
+ if (!ath_rc_valid_phyrate(phy, capflag, FALSE))
+ continue;
+
+ rate_ctrl->valid_phy_rateidx[phy]
+ [rate_ctrl->valid_phy_ratecnt[phy]] = j;
+ rate_ctrl->valid_phy_ratecnt[phy] += 1;
+ ath_rc_set_valid_txmask(rate_ctrl, j, TRUE);
+ hi = A_MAX(hi, j);
+ }
+ }
+ return hi;
+}
+
+/*
+ * Attach to a device instance. Setup the public definition
+ * of how much per-node space we need and setup the private
+ * phy tables that have rate control parameters.
+ */
+struct ath_rate_softc *ath_rate_attach(struct ath_hal *ah)
+{
+ struct ath_rate_softc *asc;
+
+ /* we are only in user context so we can sleep for memory */
+ asc = kzalloc(sizeof(struct ath_rate_softc), GFP_KERNEL);
+ if (asc == NULL)
+ return NULL;
+
+ ar5416_attach_ratetables(asc);
+
+ /* Save Maximum TX Trigger Level (used for 11n) */
+ tx_triglevel_max = ah->ah_caps.tx_triglevel_max;
+ /* return alias for ath_rate_softc * */
+ return asc;
+}
+
+static struct ath_rate_node *ath_rate_node_alloc(struct ath_vap *avp,
+ struct ath_rate_softc *rsc,
+ gfp_t gfp)
+{
+ struct ath_rate_node *anode;
+
+ anode = kzalloc(sizeof(struct ath_rate_node), gfp);
+ if (anode == NULL)
+ return NULL;
+
+ anode->avp = avp;
+ anode->asc = rsc;
+ avp->rc_node = anode;
+
+ return anode;
+}
+
+static void ath_rate_node_free(struct ath_rate_node *anode)
+{
+ if (anode != NULL)
+ kfree(anode);
+}
+
+void ath_rate_detach(struct ath_rate_softc *asc)
+{
+ if (asc != NULL)
+ kfree(asc);
+}
+
+u8 ath_rate_findrateix(struct ath_softc *sc,
+ u8 dot11rate)
+{
+ const struct ath_rate_table *ratetable;
+ struct ath_rate_softc *rsc = sc->sc_rc;
+ int i;
+
+ ratetable = rsc->hw_rate_table[sc->sc_curmode];
+
+ if (WARN_ON(!ratetable))
+ return 0;
+
+ for (i = 0; i < ratetable->rate_cnt; i++) {
+ if ((ratetable->info[i].dot11rate & 0x7f) == (dot11rate & 0x7f))
+ return i;
+ }
+
+ return 0;
+}
+
+/*
+ * Update rate-control state on a device state change. When
+ * operating as a station this includes associate/reassociate
+ * with an AP. Otherwise this gets called, for example, when
+ * the we transition to run state when operating as an AP.
+ */
+void ath_rate_newstate(struct ath_softc *sc, struct ath_vap *avp)
+{
+ struct ath_rate_softc *asc = sc->sc_rc;
+
+ /* For half and quarter rate channles use different
+ * rate tables
+ */
+ if (sc->sc_curchan.channelFlags & CHANNEL_HALF)
+ ar5416_sethalf_ratetable(asc);
+ else if (sc->sc_curchan.channelFlags & CHANNEL_QUARTER)
+ ar5416_setquarter_ratetable(asc);
+ else /* full rate */
+ ar5416_setfull_ratetable(asc);
+
+ if (avp->av_config.av_fixed_rateset != IEEE80211_FIXED_RATE_NONE) {
+ asc->fixedrix =
+ sc->sc_rixmap[avp->av_config.av_fixed_rateset & 0xff];
+ /* NB: check the fixed rate exists */
+ if (asc->fixedrix == 0xff)
+ asc->fixedrix = IEEE80211_FIXED_RATE_NONE;
+ } else {
+ asc->fixedrix = IEEE80211_FIXED_RATE_NONE;
+ }
+}
+
+static u8 ath_rc_ratefind_ht(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ const struct ath_rate_table *rate_table,
+ int probe_allowed, int *is_probing,
+ int is_retry)
+{
+ u32 dt, best_thruput, this_thruput, now_msec;
+ u8 rate, next_rate, best_rate, maxindex, minindex;
+ int8_t rssi_last, rssi_reduce = 0, index = 0;
+ struct ath_tx_ratectrl *rate_ctrl = NULL;
+
+ rate_ctrl = (struct ath_tx_ratectrl *)(ath_rc_priv ?
+ (ath_rc_priv) : NULL);
+
+ *is_probing = FALSE;
+
+ rssi_last = median(rate_ctrl->rssi_last,
+ rate_ctrl->rssi_last_prev,
+ rate_ctrl->rssi_last_prev2);
+
+ /*
+ * Age (reduce) last ack rssi based on how old it is.
+ * The bizarre numbers are so the delta is 160msec,
+ * meaning we divide by 16.
+ * 0msec <= dt <= 25msec: don't derate
+ * 25msec <= dt <= 185msec: derate linearly from 0 to 10dB
+ * 185msec <= dt: derate by 10dB
+ */
+
+ now_msec = jiffies_to_msecs(jiffies);
+ dt = now_msec - rate_ctrl->rssi_time;
+
+ if (dt >= 185)
+ rssi_reduce = 10;
+ else if (dt >= 25)
+ rssi_reduce = (u8)((dt - 25) >> 4);
+
+ /* Now reduce rssi_last by rssi_reduce */
+ if (rssi_last < rssi_reduce)
+ rssi_last = 0;
+ else
+ rssi_last -= rssi_reduce;
+
+ /*
+ * Now look up the rate in the rssi table and return it.
+ * If no rates match then we return 0 (lowest rate)
+ */
+
+ best_thruput = 0;
+ maxindex = rate_ctrl->max_valid_rate-1;
+
+ minindex = 0;
+ best_rate = minindex;
+
+ /*
+ * Try the higher rate first. It will reduce memory moving time
+ * if we have very good channel characteristics.
+ */
+ for (index = maxindex; index >= minindex ; index--) {
+ u8 per_thres;
+
+ rate = rate_ctrl->valid_rate_index[index];
+ if (rate > rate_ctrl->rate_max_phy)
+ continue;
+
+ /*
+ * For TCP the average collision rate is around 11%,
+ * so we ignore PERs less than this. This is to
+ * prevent the rate we are currently using (whose
+ * PER might be in the 10-15 range because of TCP
+ * collisions) looking worse than the next lower
+ * rate whose PER has decayed close to 0. If we
+ * used to next lower rate, its PER would grow to
+ * 10-15 and we would be worse off then staying
+ * at the current rate.
+ */
+ per_thres = rate_ctrl->state[rate].per;
+ if (per_thres < 12)
+ per_thres = 12;
+
+ this_thruput = rate_table->info[rate].user_ratekbps *
+ (100 - per_thres);
+
+ if (best_thruput <= this_thruput) {
+ best_thruput = this_thruput;
+ best_rate = rate;
+ }
+ }
+
+ rate = best_rate;
+
+ /* if we are retrying for more than half the number
+ * of max retries, use the min rate for the next retry
+ */
+ if (is_retry)
+ rate = rate_ctrl->valid_rate_index[minindex];
+
+ rate_ctrl->rssi_last_lookup = rssi_last;
+
+ /*
+ * Must check the actual rate (ratekbps) to account for
+ * non-monoticity of 11g's rate table
+ */
+
+ if (rate >= rate_ctrl->rate_max_phy && probe_allowed) {
+ rate = rate_ctrl->rate_max_phy;
+
+ /* Probe the next allowed phy state */
+ /* FIXME:XXXX Check to make sure ratMax is checked properly */
+ if (ath_rc_get_nextvalid_txrate(rate_table,
+ rate_ctrl, rate, &next_rate) &&
+ (now_msec - rate_ctrl->probe_time >
+ rate_table->probe_interval) &&
+ (rate_ctrl->hw_maxretry_pktcnt >= 1)) {
+ rate = next_rate;
+ rate_ctrl->probe_rate = rate;
+ rate_ctrl->probe_time = now_msec;
+ rate_ctrl->hw_maxretry_pktcnt = 0;
+ *is_probing = TRUE;
+ }
+ }
+
+ /*
+ * Make sure rate is not higher than the allowed maximum.
+ * We should also enforce the min, but I suspect the min is
+ * normally 1 rather than 0 because of the rate 9 vs 6 issue
+ * in the old code.
+ */
+ if (rate > (rate_ctrl->rate_table_size - 1))
+ rate = rate_ctrl->rate_table_size - 1;
+
+ ASSERT((rate_table->info[rate].valid && !ath_rc_priv->single_stream) ||
+ (rate_table->info[rate].valid_single_stream &&
+ ath_rc_priv->single_stream));
+
+ return rate;
+}
+
+static void ath_rc_rate_set_series(const struct ath_rate_table *rate_table ,
+ struct ath_rc_series *series,
+ u8 tries,
+ u8 rix,
+ int rtsctsenable)
+{
+ series->tries = tries;
+ series->flags = (rtsctsenable ? ATH_RC_RTSCTS_FLAG : 0) |
+ (WLAN_RC_PHY_DS(rate_table->info[rix].phy) ?
+ ATH_RC_DS_FLAG : 0) |
+ (WLAN_RC_PHY_40(rate_table->info[rix].phy) ?
+ ATH_RC_CW40_FLAG : 0) |
+ (WLAN_RC_PHY_SGI(rate_table->info[rix].phy) ?
+ ATH_RC_SGI_FLAG : 0);
+
+ series->rix = rate_table->info[rix].base_index;
+ series->max_4ms_framelen = rate_table->info[rix].max_4ms_framelen;
+}
+
+static u8 ath_rc_rate_getidx(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ const struct ath_rate_table *rate_table,
+ u8 rix, u16 stepdown,
+ u16 min_rate)
+{
+ u32 j;
+ u8 nextindex;
+ struct ath_tx_ratectrl *rate_ctrl =
+ (struct ath_tx_ratectrl *)(ath_rc_priv);
+
+ if (min_rate) {
+ for (j = RATE_TABLE_SIZE; j > 0; j--) {
+ if (ath_rc_get_nextlowervalid_txrate(rate_table,
+ rate_ctrl, rix, &nextindex))
+ rix = nextindex;
+ else
+ break;
+ }
+ } else {
+ for (j = stepdown; j > 0; j--) {
+ if (ath_rc_get_nextlowervalid_txrate(rate_table,
+ rate_ctrl, rix, &nextindex))
+ rix = nextindex;
+ else
+ break;
+ }
+ }
+ return rix;
+}
+
+static void ath_rc_ratefind(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ int num_tries, int num_rates, unsigned int rcflag,
+ struct ath_rc_series series[], int *is_probe,
+ int is_retry)
+{
+ u8 try_per_rate = 0, i = 0, rix, nrix;
+ struct ath_rate_softc *asc = (struct ath_rate_softc *)sc->sc_rc;
+ struct ath_rate_table *rate_table;
+
+ rate_table =
+ (struct ath_rate_table *)asc->hw_rate_table[sc->sc_curmode];
+ rix = ath_rc_ratefind_ht(sc, ath_rc_priv, rate_table,
+ (rcflag & ATH_RC_PROBE_ALLOWED) ? 1 : 0,
+ is_probe, is_retry);
+ nrix = rix;
+
+ if ((rcflag & ATH_RC_PROBE_ALLOWED) && (*is_probe)) {
+ /* set one try for probe rates. For the
+ * probes don't enable rts */
+ ath_rc_rate_set_series(rate_table,
+ &series[i++], 1, nrix, FALSE);
+
+ try_per_rate = (num_tries/num_rates);
+ /* Get the next tried/allowed rate. No RTS for the next series
+ * after the probe rate
+ */
+ nrix = ath_rc_rate_getidx(sc,
+ ath_rc_priv, rate_table, nrix, 1, FALSE);
+ ath_rc_rate_set_series(rate_table,
+ &series[i++], try_per_rate, nrix, 0);
+ } else {
+ try_per_rate = (num_tries/num_rates);
+ /* Set the choosen rate. No RTS for first series entry. */
+ ath_rc_rate_set_series(rate_table,
+ &series[i++], try_per_rate, nrix, FALSE);
+ }
+
+ /* Fill in the other rates for multirate retry */
+ for ( ; i < num_rates; i++) {
+ u8 try_num;
+ u8 min_rate;
+
+ try_num = ((i + 1) == num_rates) ?
+ num_tries - (try_per_rate * i) : try_per_rate ;
+ min_rate = (((i + 1) == num_rates) &&
+ (rcflag & ATH_RC_MINRATE_LASTRATE)) ? 1 : 0;
+
+ nrix = ath_rc_rate_getidx(sc, ath_rc_priv,
+ rate_table, nrix, 1, min_rate);
+ /* All other rates in the series have RTS enabled */
+ ath_rc_rate_set_series(rate_table,
+ &series[i], try_num, nrix, TRUE);
+ }
+
+ /*
+ * NB:Change rate series to enable aggregation when operating
+ * at lower MCS rates. When first rate in series is MCS2
+ * in HT40 @ 2.4GHz, series should look like:
+ *
+ * {MCS2, MCS1, MCS0, MCS0}.
+ *
+ * When first rate in series is MCS3 in HT20 @ 2.4GHz, series should
+ * look like:
+ *
+ * {MCS3, MCS2, MCS1, MCS1}
+ *
+ * So, set fourth rate in series to be same as third one for
+ * above conditions.
+ */
+ if ((sc->sc_curmode == ATH9K_MODE_11NG_HT20) ||
+ (sc->sc_curmode == ATH9K_MODE_11NG_HT40PLUS) ||
+ (sc->sc_curmode == ATH9K_MODE_11NG_HT40MINUS)) {
+ u8 dot11rate = rate_table->info[rix].dot11rate;
+ u8 phy = rate_table->info[rix].phy;
+ if (i == 4 &&
+ ((dot11rate == 2 && phy == WLAN_RC_PHY_HT_40_SS) ||
+ (dot11rate == 3 && phy == WLAN_RC_PHY_HT_20_SS))) {
+ series[3].rix = series[2].rix;
+ series[3].flags = series[2].flags;
+ series[3].max_4ms_framelen = series[2].max_4ms_framelen;
+ }
+ }
+}
+
+/*
+ * Return the Tx rate series.
+ */
+void ath_rate_findrate(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ int num_tries,
+ int num_rates,
+ unsigned int rcflag,
+ struct ath_rc_series series[],
+ int *is_probe,
+ int is_retry)
+{
+ struct ath_vap *avp = ath_rc_priv->avp;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s", __func__);
+ if (!num_rates || !num_tries)
+ return;
+
+ if (avp->av_config.av_fixed_rateset == IEEE80211_FIXED_RATE_NONE) {
+ ath_rc_ratefind(sc, ath_rc_priv, num_tries, num_rates,
+ rcflag, series, is_probe, is_retry);
+ } else {
+ /* Fixed rate */
+ int idx;
+ u8 flags;
+ u32 rix;
+ struct ath_rate_softc *asc = ath_rc_priv->asc;
+ struct ath_rate_table *rate_table;
+
+ rate_table = (struct ath_rate_table *)
+ asc->hw_rate_table[sc->sc_curmode];
+
+ for (idx = 0; idx < 4; idx++) {
+ unsigned int mcs;
+ u8 series_rix = 0;
+
+ series[idx].tries =
+ IEEE80211_RATE_IDX_ENTRY(
+ avp->av_config.av_fixed_retryset, idx);
+
+ mcs = IEEE80211_RATE_IDX_ENTRY(
+ avp->av_config.av_fixed_rateset, idx);
+
+ if (idx == 3 && (mcs & 0xf0) == 0x70)
+ mcs = (mcs & ~0xf0)|0x80;
+
+ if (!(mcs & 0x80))
+ flags = 0;
+ else
+ flags = ((ath_rc_priv->ht_cap &
+ WLAN_RC_DS_FLAG) ?
+ ATH_RC_DS_FLAG : 0) |
+ ((ath_rc_priv->ht_cap &
+ WLAN_RC_40_FLAG) ?
+ ATH_RC_CW40_FLAG : 0) |
+ ((ath_rc_priv->ht_cap &
+ WLAN_RC_SGI_FLAG) ?
+ ((ath_rc_priv->ht_cap &
+ WLAN_RC_40_FLAG) ?
+ ATH_RC_SGI_FLAG : 0) : 0);
+
+ series[idx].rix = sc->sc_rixmap[mcs];
+ series_rix = series[idx].rix;
+
+ /* XXX: Give me some cleanup love */
+ if ((flags & ATH_RC_CW40_FLAG) &&
+ (flags & ATH_RC_SGI_FLAG))
+ rix = rate_table->info[series_rix].ht_index;
+ else if (flags & ATH_RC_SGI_FLAG)
+ rix = rate_table->info[series_rix].sgi_index;
+ else if (flags & ATH_RC_CW40_FLAG)
+ rix = rate_table->info[series_rix].cw40index;
+ else
+ rix = rate_table->info[series_rix].base_index;
+ series[idx].max_4ms_framelen =
+ rate_table->info[rix].max_4ms_framelen;
+ series[idx].flags = flags;
+ }
+ }
+}
+
+static void ath_rc_update_ht(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ struct ath_tx_info_priv *info_priv,
+ int tx_rate, int xretries, int retries)
+{
+ struct ath_tx_ratectrl *rate_ctrl;
+ u32 now_msec = jiffies_to_msecs(jiffies);
+ int state_change = FALSE, rate, count;
+ u8 last_per;
+ struct ath_rate_softc *asc = (struct ath_rate_softc *)sc->sc_rc;
+ struct ath_rate_table *rate_table =
+ (struct ath_rate_table *)asc->hw_rate_table[sc->sc_curmode];
+
+ static u32 nretry_to_per_lookup[10] = {
+ 100 * 0 / 1,
+ 100 * 1 / 4,
+ 100 * 1 / 2,
+ 100 * 3 / 4,
+ 100 * 4 / 5,
+ 100 * 5 / 6,
+ 100 * 6 / 7,
+ 100 * 7 / 8,
+ 100 * 8 / 9,
+ 100 * 9 / 10
+ };
+
+ if (!ath_rc_priv)
+ return;
+
+ rate_ctrl = (struct ath_tx_ratectrl *)(ath_rc_priv);
+
+ ASSERT(tx_rate >= 0);
+ if (tx_rate < 0)
+ return;
+
+ /* To compensate for some imbalance between ctrl and ext. channel */
+
+ if (WLAN_RC_PHY_40(rate_table->info[tx_rate].phy))
+ info_priv->tx.ts_rssi =
+ info_priv->tx.ts_rssi < 3 ? 0 :
+ info_priv->tx.ts_rssi - 3;
+
+ last_per = rate_ctrl->state[tx_rate].per;
+
+ if (xretries) {
+ /* Update the PER. */
+ if (xretries == 1) {
+ rate_ctrl->state[tx_rate].per += 30;
+ if (rate_ctrl->state[tx_rate].per > 100)
+ rate_ctrl->state[tx_rate].per = 100;
+ } else {
+ /* xretries == 2 */
+ count = sizeof(nretry_to_per_lookup) /
+ sizeof(nretry_to_per_lookup[0]);
+ if (retries >= count)
+ retries = count - 1;
+ /* new_PER = 7/8*old_PER + 1/8*(currentPER) */
+ rate_ctrl->state[tx_rate].per =
+ (u8)(rate_ctrl->state[tx_rate].per -
+ (rate_ctrl->state[tx_rate].per >> 3) +
+ ((100) >> 3));
+ }
+
+ /* xretries == 1 or 2 */
+
+ if (rate_ctrl->probe_rate == tx_rate)
+ rate_ctrl->probe_rate = 0;
+
+ } else { /* xretries == 0 */
+ /* Update the PER. */
+ /* Make sure it doesn't index out of array's bounds. */
+ count = sizeof(nretry_to_per_lookup) /
+ sizeof(nretry_to_per_lookup[0]);
+ if (retries >= count)
+ retries = count - 1;
+ if (info_priv->n_bad_frames) {
+ /* new_PER = 7/8*old_PER + 1/8*(currentPER) */
+ /*
+ * Assuming that n_frames is not 0. The current PER
+ * from the retries is 100 * retries / (retries+1),
+ * since the first retries attempts failed, and the
+ * next one worked. For the one that worked,
+ * n_bad_frames subframes out of n_frames wored,
+ * so the PER for that part is
+ * 100 * n_bad_frames / n_frames, and it contributes
+ * 100 * n_bad_frames / (n_frames * (retries+1)) to
+ * the above PER. The expression below is a
+ * simplified version of the sum of these two terms.
+ */
+ if (info_priv->n_frames > 0)
+ rate_ctrl->state[tx_rate].per
+ = (u8)
+ (rate_ctrl->state[tx_rate].per -
+ (rate_ctrl->state[tx_rate].per >> 3) +
+ ((100*(retries*info_priv->n_frames +
+ info_priv->n_bad_frames) /
+ (info_priv->n_frames *
+ (retries+1))) >> 3));
+ } else {
+ /* new_PER = 7/8*old_PER + 1/8*(currentPER) */
+
+ rate_ctrl->state[tx_rate].per = (u8)
+ (rate_ctrl->state[tx_rate].per -
+ (rate_ctrl->state[tx_rate].per >> 3) +
+ (nretry_to_per_lookup[retries] >> 3));
+ }
+
+ rate_ctrl->rssi_last_prev2 = rate_ctrl->rssi_last_prev;
+ rate_ctrl->rssi_last_prev = rate_ctrl->rssi_last;
+ rate_ctrl->rssi_last = info_priv->tx.ts_rssi;
+ rate_ctrl->rssi_time = now_msec;
+
+ /*
+ * If we got at most one retry then increase the max rate if
+ * this was a probe. Otherwise, ignore the probe.
+ */
+
+ if (rate_ctrl->probe_rate && rate_ctrl->probe_rate == tx_rate) {
+ if (retries > 0 || 2 * info_priv->n_bad_frames >
+ info_priv->n_frames) {
+ /*
+ * Since we probed with just a single attempt,
+ * any retries means the probe failed. Also,
+ * if the attempt worked, but more than half
+ * the subframes were bad then also consider
+ * the probe a failure.
+ */
+ rate_ctrl->probe_rate = 0;
+ } else {
+ u8 probe_rate = 0;
+
+ rate_ctrl->rate_max_phy = rate_ctrl->probe_rate;
+ probe_rate = rate_ctrl->probe_rate;
+
+ if (rate_ctrl->state[probe_rate].per > 30)
+ rate_ctrl->state[probe_rate].per = 20;
+
+ rate_ctrl->probe_rate = 0;
+
+ /*
+ * Since this probe succeeded, we allow the next
+ * probe twice as soon. This allows the maxRate
+ * to move up faster if the probes are
+ * succesful.
+ */
+ rate_ctrl->probe_time = now_msec -
+ rate_table->probe_interval / 2;
+ }
+ }
+
+ if (retries > 0) {
+ /*
+ * Don't update anything. We don't know if
+ * this was because of collisions or poor signal.
+ *
+ * Later: if rssi_ack is close to
+ * rate_ctrl->state[txRate].rssi_thres and we see lots
+ * of retries, then we could increase
+ * rate_ctrl->state[txRate].rssi_thres.
+ */
+ rate_ctrl->hw_maxretry_pktcnt = 0;
+ } else {
+ /*
+ * It worked with no retries. First ignore bogus (small)
+ * rssi_ack values.
+ */
+ if (tx_rate == rate_ctrl->rate_max_phy &&
+ rate_ctrl->hw_maxretry_pktcnt < 255) {
+ rate_ctrl->hw_maxretry_pktcnt++;
+ }
+
+ if (info_priv->tx.ts_rssi >=
+ rate_table->info[tx_rate].rssi_ack_validmin) {
+ /* Average the rssi */
+ if (tx_rate != rate_ctrl->rssi_sum_rate) {
+ rate_ctrl->rssi_sum_rate = tx_rate;
+ rate_ctrl->rssi_sum =
+ rate_ctrl->rssi_sum_cnt = 0;
+ }
+
+ rate_ctrl->rssi_sum += info_priv->tx.ts_rssi;
+ rate_ctrl->rssi_sum_cnt++;
+
+ if (rate_ctrl->rssi_sum_cnt > 4) {
+ int32_t rssi_ackAvg =
+ (rate_ctrl->rssi_sum + 2) / 4;
+ int8_t rssi_thres =
+ rate_ctrl->state[tx_rate].
+ rssi_thres;
+ int8_t rssi_ack_vmin =
+ rate_table->info[tx_rate].
+ rssi_ack_validmin;
+
+ rate_ctrl->rssi_sum =
+ rate_ctrl->rssi_sum_cnt = 0;
+
+ /* Now reduce the current
+ * rssi threshold. */
+ if ((rssi_ackAvg < rssi_thres + 2) &&
+ (rssi_thres > rssi_ack_vmin)) {
+ rate_ctrl->state[tx_rate].
+ rssi_thres--;
+ }
+
+ state_change = TRUE;
+ }
+ }
+ }
+ }
+
+ /* For all cases */
+
+ /*
+ * If this rate looks bad (high PER) then stop using it for
+ * a while (except if we are probing).
+ */
+ if (rate_ctrl->state[tx_rate].per >= 55 && tx_rate > 0 &&
+ rate_table->info[tx_rate].ratekbps <=
+ rate_table->info[rate_ctrl->rate_max_phy].ratekbps) {
+ ath_rc_get_nextlowervalid_txrate(rate_table, rate_ctrl,
+ (u8) tx_rate, &rate_ctrl->rate_max_phy);
+
+ /* Don't probe for a little while. */
+ rate_ctrl->probe_time = now_msec;
+ }
+
+ if (state_change) {
+ /*
+ * Make sure the rates above this have higher rssi thresholds.
+ * (Note: Monotonicity is kept within the OFDM rates and
+ * within the CCK rates. However, no adjustment is
+ * made to keep the rssi thresholds monotonically
+ * increasing between the CCK and OFDM rates.)
+ */
+ for (rate = tx_rate; rate <
+ rate_ctrl->rate_table_size - 1; rate++) {
+ if (rate_table->info[rate+1].phy !=
+ rate_table->info[tx_rate].phy)
+ break;
+
+ if (rate_ctrl->state[rate].rssi_thres +
+ rate_table->info[rate].rssi_ack_deltamin >
+ rate_ctrl->state[rate+1].rssi_thres) {
+ rate_ctrl->state[rate+1].rssi_thres =
+ rate_ctrl->state[rate].
+ rssi_thres +
+ rate_table->info[rate].
+ rssi_ack_deltamin;
+ }
+ }
+
+ /* Make sure the rates below this have lower rssi thresholds. */
+ for (rate = tx_rate - 1; rate >= 0; rate--) {
+ if (rate_table->info[rate].phy !=
+ rate_table->info[tx_rate].phy)
+ break;
+
+ if (rate_ctrl->state[rate].rssi_thres +
+ rate_table->info[rate].rssi_ack_deltamin >
+ rate_ctrl->state[rate+1].rssi_thres) {
+ if (rate_ctrl->state[rate+1].rssi_thres <
+ rate_table->info[rate].
+ rssi_ack_deltamin)
+ rate_ctrl->state[rate].rssi_thres = 0;
+ else {
+ rate_ctrl->state[rate].rssi_thres =
+ rate_ctrl->state[rate+1].
+ rssi_thres -
+ rate_table->info[rate].
+ rssi_ack_deltamin;
+ }
+
+ if (rate_ctrl->state[rate].rssi_thres <
+ rate_table->info[rate].
+ rssi_ack_validmin) {
+ rate_ctrl->state[rate].rssi_thres =
+ rate_table->info[rate].
+ rssi_ack_validmin;
+ }
+ }
+ }
+ }
+
+ /* Make sure the rates below this have lower PER */
+ /* Monotonicity is kept only for rates below the current rate. */
+ if (rate_ctrl->state[tx_rate].per < last_per) {
+ for (rate = tx_rate - 1; rate >= 0; rate--) {
+ if (rate_table->info[rate].phy !=
+ rate_table->info[tx_rate].phy)
+ break;
+
+ if (rate_ctrl->state[rate].per >
+ rate_ctrl->state[rate+1].per) {
+ rate_ctrl->state[rate].per =
+ rate_ctrl->state[rate+1].per;
+ }
+ }
+ }
+
+ /* Maintain monotonicity for rates above the current rate */
+ for (rate = tx_rate; rate < rate_ctrl->rate_table_size - 1; rate++) {
+ if (rate_ctrl->state[rate+1].per < rate_ctrl->state[rate].per)
+ rate_ctrl->state[rate+1].per =
+ rate_ctrl->state[rate].per;
+ }
+
+ /* Every so often, we reduce the thresholds and
+ * PER (different for CCK and OFDM). */
+ if (now_msec - rate_ctrl->rssi_down_time >=
+ rate_table->rssi_reduce_interval) {
+
+ for (rate = 0; rate < rate_ctrl->rate_table_size; rate++) {
+ if (rate_ctrl->state[rate].rssi_thres >
+ rate_table->info[rate].rssi_ack_validmin)
+ rate_ctrl->state[rate].rssi_thres -= 1;
+ }
+ rate_ctrl->rssi_down_time = now_msec;
+ }
+
+ /* Every so often, we reduce the thresholds
+ * and PER (different for CCK and OFDM). */
+ if (now_msec - rate_ctrl->per_down_time >=
+ rate_table->rssi_reduce_interval) {
+ for (rate = 0; rate < rate_ctrl->rate_table_size; rate++) {
+ rate_ctrl->state[rate].per =
+ 7 * rate_ctrl->state[rate].per / 8;
+ }
+
+ rate_ctrl->per_down_time = now_msec;
+ }
+}
+
+/*
+ * This routine is called in rate control callback tx_status() to give
+ * the status of previous frames.
+ */
+static void ath_rc_update(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ struct ath_tx_info_priv *info_priv, int final_ts_idx,
+ int xretries, int long_retry)
+{
+ struct ath_rate_softc *asc = (struct ath_rate_softc *)sc->sc_rc;
+ struct ath_rate_table *rate_table;
+ struct ath_tx_ratectrl *rate_ctrl;
+ struct ath_rc_series rcs[4];
+ u8 flags;
+ u32 series = 0, rix;
+
+ memcpy(rcs, info_priv->rcs, 4 * sizeof(rcs[0]));
+ rate_table = (struct ath_rate_table *)
+ asc->hw_rate_table[sc->sc_curmode];
+ rate_ctrl = (struct ath_tx_ratectrl *)(ath_rc_priv);
+ ASSERT(rcs[0].tries != 0);
+
+ /*
+ * If the first rate is not the final index, there
+ * are intermediate rate failures to be processed.
+ */
+ if (final_ts_idx != 0) {
+ /* Process intermediate rates that failed.*/
+ for (series = 0; series < final_ts_idx ; series++) {
+ if (rcs[series].tries != 0) {
+ flags = rcs[series].flags;
+ /* If HT40 and we have switched mode from
+ * 40 to 20 => don't update */
+ if ((flags & ATH_RC_CW40_FLAG) &&
+ (rate_ctrl->rc_phy_mode !=
+ (flags & ATH_RC_CW40_FLAG)))
+ return;
+ if ((flags & ATH_RC_CW40_FLAG) &&
+ (flags & ATH_RC_SGI_FLAG))
+ rix = rate_table->info[
+ rcs[series].rix].ht_index;
+ else if (flags & ATH_RC_SGI_FLAG)
+ rix = rate_table->info[
+ rcs[series].rix].sgi_index;
+ else if (flags & ATH_RC_CW40_FLAG)
+ rix = rate_table->info[
+ rcs[series].rix].cw40index;
+ else
+ rix = rate_table->info[
+ rcs[series].rix].base_index;
+ ath_rc_update_ht(sc, ath_rc_priv,
+ info_priv, rix,
+ xretries ? 1 : 2,
+ rcs[series].tries);
+ }
+ }
+ } else {
+ /*
+ * Handle the special case of MIMO PS burst, where the second
+ * aggregate is sent out with only one rate and one try.
+ * Treating it as an excessive retry penalizes the rate
+ * inordinately.
+ */
+ if (rcs[0].tries == 1 && xretries == 1)
+ xretries = 2;
+ }
+
+ flags = rcs[series].flags;
+ /* If HT40 and we have switched mode from 40 to 20 => don't update */
+ if ((flags & ATH_RC_CW40_FLAG) &&
+ (rate_ctrl->rc_phy_mode != (flags & ATH_RC_CW40_FLAG)))
+ return;
+
+ if ((flags & ATH_RC_CW40_FLAG) && (flags & ATH_RC_SGI_FLAG))
+ rix = rate_table->info[rcs[series].rix].ht_index;
+ else if (flags & ATH_RC_SGI_FLAG)
+ rix = rate_table->info[rcs[series].rix].sgi_index;
+ else if (flags & ATH_RC_CW40_FLAG)
+ rix = rate_table->info[rcs[series].rix].cw40index;
+ else
+ rix = rate_table->info[rcs[series].rix].base_index;
+
+ ath_rc_update_ht(sc, ath_rc_priv, info_priv, rix,
+ xretries, long_retry);
+}
+
+
+/*
+ * Process a tx descriptor for a completed transmit (success or failure).
+ */
+static void ath_rate_tx_complete(struct ath_softc *sc,
+ struct ath_node *an,
+ struct ath_rate_node *rc_priv,
+ struct ath_tx_info_priv *info_priv)
+{
+ int final_ts_idx = info_priv->tx.ts_rateindex;
+ int tx_status = 0, is_underrun = 0;
+ struct ath_vap *avp;
+
+ avp = rc_priv->avp;
+ if ((avp->av_config.av_fixed_rateset != IEEE80211_FIXED_RATE_NONE)
+ || info_priv->tx.ts_status & ATH9K_TXERR_FILT)
+ return;
+
+ if (info_priv->tx.ts_rssi > 0) {
+ ATH_RSSI_LPF(an->an_chainmask_sel.tx_avgrssi,
+ info_priv->tx.ts_rssi);
+ }
+
+ /*
+ * If underrun error is seen assume it as an excessive retry only
+ * if prefetch trigger level have reached the max (0x3f for 5416)
+ * Adjust the long retry as if the frame was tried ATH_11N_TXMAXTRY
+ * times. This affects how ratectrl updates PER for the failed rate.
+ */
+ if (info_priv->tx.ts_flags &
+ (ATH9K_TX_DATA_UNDERRUN | ATH9K_TX_DELIM_UNDERRUN) &&
+ ((sc->sc_ah->ah_txTrigLevel) >= tx_triglevel_max)) {
+ tx_status = 1;
+ is_underrun = 1;
+ }
+
+ if ((info_priv->tx.ts_status & ATH9K_TXERR_XRETRY) ||
+ (info_priv->tx.ts_status & ATH9K_TXERR_FIFO))
+ tx_status = 1;
+
+ ath_rc_update(sc, rc_priv, info_priv, final_ts_idx, tx_status,
+ (is_underrun) ? ATH_11N_TXMAXTRY :
+ info_priv->tx.ts_longretry);
+}
+
+
+/*
+ * Update the SIB's rate control information
+ *
+ * This should be called when the supported rates change
+ * (e.g. SME operation, wireless mode change)
+ *
+ * It will determine which rates are valid for use.
+ */
+static void ath_rc_sib_update(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ u32 capflag, int keep_state,
+ struct ath_rateset *negotiated_rates,
+ struct ath_rateset *negotiated_htrates)
+{
+ struct ath_rate_table *rate_table = NULL;
+ struct ath_rate_softc *asc = (struct ath_rate_softc *)sc->sc_rc;
+ struct ath_rateset *rateset = negotiated_rates;
+ u8 *ht_mcs = (u8 *)negotiated_htrates;
+ struct ath_tx_ratectrl *rate_ctrl = (struct ath_tx_ratectrl *)
+ (ath_rc_priv);
+ u8 i, j, k, hi = 0, hthi = 0;
+
+ rate_table = (struct ath_rate_table *)
+ asc->hw_rate_table[sc->sc_curmode];
+
+ /* Initial rate table size. Will change depending
+ * on the working rate set */
+ rate_ctrl->rate_table_size = MAX_TX_RATE_TBL;
+
+ /* Initialize thresholds according to the global rate table */
+ for (i = 0 ; (i < rate_ctrl->rate_table_size) && (!keep_state); i++) {
+ rate_ctrl->state[i].rssi_thres =
+ rate_table->info[i].rssi_ack_validmin;
+ rate_ctrl->state[i].per = 0;
+ }
+
+ /* Determine the valid rates */
+ ath_rc_init_valid_txmask(rate_ctrl);
+
+ for (i = 0; i < WLAN_RC_PHY_MAX; i++) {
+ for (j = 0; j < MAX_TX_RATE_PHY; j++)
+ rate_ctrl->valid_phy_rateidx[i][j] = 0;
+ rate_ctrl->valid_phy_ratecnt[i] = 0;
+ }
+ rate_ctrl->rc_phy_mode = (capflag & WLAN_RC_40_FLAG);
+
+ /* Set stream capability */
+ ath_rc_priv->single_stream = (capflag & WLAN_RC_DS_FLAG) ? 0 : 1;
+
+ if (!rateset->rs_nrates) {
+ /* No working rate, just initialize valid rates */
+ hi = ath_rc_sib_init_validrates(ath_rc_priv, rate_table,
+ capflag);
+ } else {
+ /* Use intersection of working rates and valid rates */
+ hi = ath_rc_sib_setvalid_rates(ath_rc_priv, rate_table,
+ rateset, capflag);
+ if (capflag & WLAN_RC_HT_FLAG) {
+ hthi = ath_rc_sib_setvalid_htrates(ath_rc_priv,
+ rate_table,
+ ht_mcs,
+ capflag);
+ }
+ hi = A_MAX(hi, hthi);
+ }
+
+ rate_ctrl->rate_table_size = hi + 1;
+ rate_ctrl->rate_max_phy = 0;
+ ASSERT(rate_ctrl->rate_table_size <= MAX_TX_RATE_TBL);
+
+ for (i = 0, k = 0; i < WLAN_RC_PHY_MAX; i++) {
+ for (j = 0; j < rate_ctrl->valid_phy_ratecnt[i]; j++) {
+ rate_ctrl->valid_rate_index[k++] =
+ rate_ctrl->valid_phy_rateidx[i][j];
+ }
+
+ if (!ath_rc_valid_phyrate(i, rate_table->initial_ratemax, TRUE)
+ || !rate_ctrl->valid_phy_ratecnt[i])
+ continue;
+
+ rate_ctrl->rate_max_phy = rate_ctrl->valid_phy_rateidx[i][j-1];
+ }
+ ASSERT(rate_ctrl->rate_table_size <= MAX_TX_RATE_TBL);
+ ASSERT(k <= MAX_TX_RATE_TBL);
+
+ rate_ctrl->max_valid_rate = k;
+ /*
+ * Some third party vendors don't send the supported rate series in
+ * order. So sorting to make sure its in order, otherwise our RateFind
+ * Algo will select wrong rates
+ */
+ ath_rc_sort_validrates(rate_table, rate_ctrl);
+ rate_ctrl->rate_max_phy = rate_ctrl->valid_rate_index[k-4];
+}
+
+/*
+ * Update rate-control state on station associate/reassociate.
+ */
+static int ath_rate_newassoc(struct ath_softc *sc,
+ struct ath_rate_node *ath_rc_priv,
+ unsigned int capflag,
+ struct ath_rateset *negotiated_rates,
+ struct ath_rateset *negotiated_htrates)
+{
+
+
+ ath_rc_priv->ht_cap =
+ ((capflag & ATH_RC_DS_FLAG) ? WLAN_RC_DS_FLAG : 0) |
+ ((capflag & ATH_RC_SGI_FLAG) ? WLAN_RC_SGI_FLAG : 0) |
+ ((capflag & ATH_RC_HT_FLAG) ? WLAN_RC_HT_FLAG : 0) |
+ ((capflag & ATH_RC_CW40_FLAG) ? WLAN_RC_40_FLAG : 0);
+
+ ath_rc_sib_update(sc, ath_rc_priv, ath_rc_priv->ht_cap, 0,
+ negotiated_rates, negotiated_htrates);
+
+ return 0;
+}
+
+/*
+ * This routine is called to initialize the rate control parameters
+ * in the SIB. It is called initially during system initialization
+ * or when a station is associated with the AP.
+ */
+static void ath_rc_sib_init(struct ath_rate_node *ath_rc_priv)
+{
+ struct ath_tx_ratectrl *rate_ctrl;
+
+ rate_ctrl = (struct ath_tx_ratectrl *)(ath_rc_priv);
+ rate_ctrl->rssi_down_time = jiffies_to_msecs(jiffies);
+}
+
+
+static void ath_setup_rates(struct ieee80211_local *local, struct sta_info *sta)
+
+{
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_hw *hw = local_to_hw(local);
+ struct ath_softc *sc = hw->priv;
+ struct ath_rate_node *rc_priv = sta->rate_ctrl_priv;
+ int i, j = 0;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s", __func__);
+ sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if (sta->supp_rates[local->hw.conf.channel->band] & BIT(i)) {
+ rc_priv->neg_rates.rs_rates[j]
+ = (sband->bitrates[i].bitrate * 2) / 10;
+ j++;
+ }
+ }
+ rc_priv->neg_rates.rs_nrates = j;
+}
+
+void ath_rc_node_update(struct ieee80211_hw *hw, struct ath_rate_node *rc_priv)
+{
+ struct ath_softc *sc = hw->priv;
+ u32 capflag = 0;
+
+ if (hw->conf.ht_conf.ht_supported) {
+ capflag |= ATH_RC_HT_FLAG | ATH_RC_DS_FLAG;
+ if (sc->sc_ht_info.tx_chan_width == ATH9K_HT_MACMODE_2040)
+ capflag |= ATH_RC_CW40_FLAG;
+ }
+
+ ath_rate_newassoc(sc, rc_priv, capflag,
+ &rc_priv->neg_rates,
+ &rc_priv->neg_ht_rates);
+
+}
+
+/* Rate Control callbacks */
+static void ath_tx_status(void *priv, struct net_device *dev,
+ struct sk_buff *skb)
+{
+ struct ath_softc *sc = priv;
+ struct ath_tx_info_priv *tx_info_priv;
+ struct ath_node *an;
+ struct sta_info *sta;
+ struct ieee80211_local *local;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_hdr *hdr;
+ __le16 fc;
+
+ local = hw_to_local(sc->hw);
+ hdr = (struct ieee80211_hdr *)skb->data;
+ fc = hdr->frame_control;
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, hdr->addr1);
+ spin_unlock_bh(&sc->node_lock);
+
+ sta = sta_info_get(local, hdr->addr1);
+ if (!an || !sta || !ieee80211_is_data(fc)) {
+ if (tx_info->driver_data[0] != NULL) {
+ kfree(tx_info->driver_data[0]);
+ tx_info->driver_data[0] = NULL;
+ }
+ return;
+ }
+ if (tx_info->driver_data[0] != NULL) {
+ ath_rate_tx_complete(sc, an, sta->rate_ctrl_priv, tx_info_priv);
+ kfree(tx_info->driver_data[0]);
+ tx_info->driver_data[0] = NULL;
+ }
+}
+
+static void ath_tx_aggr_resp(struct ath_softc *sc,
+ struct sta_info *sta,
+ struct ath_node *an,
+ u8 tidno)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_local *local;
+ struct ath_atx_tid *txtid;
+ struct ieee80211_supported_band *sband;
+ u16 buffersize = 0;
+ int state;
+ DECLARE_MAC_BUF(mac);
+
+ if (!sc->sc_txaggr)
+ return;
+
+ txtid = ATH_AN_2_TID(an, tidno);
+ if (!txtid->paused)
+ return;
+
+ local = hw_to_local(sc->hw);
+ sband = hw->wiphy->bands[hw->conf.channel->band];
+ buffersize = IEEE80211_MIN_AMPDU_BUF <<
+ sband->ht_info.ampdu_factor; /* FIXME */
+ state = sta->ampdu_mlme.tid_state_tx[tidno];
+
+ if (state & HT_ADDBA_RECEIVED_MSK) {
+ txtid->addba_exchangecomplete = 1;
+ txtid->addba_exchangeinprogress = 0;
+ txtid->baw_size = buffersize;
+
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Resuming tid, buffersize: %d\n",
+ __func__,
+ buffersize);
+
+ ath_tx_resume_tid(sc, txtid);
+ }
+}
+
+static void ath_get_rate(void *priv, struct net_device *dev,
+ struct ieee80211_supported_band *sband,
+ struct sk_buff *skb,
+ struct rate_selection *sel)
+{
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+ struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
+ struct sta_info *sta;
+ struct ath_softc *sc = (struct ath_softc *)priv;
+ struct ieee80211_hw *hw = sc->hw;
+ struct ath_tx_info_priv *tx_info_priv;
+ struct ath_rate_node *ath_rc_priv;
+ struct ath_node *an;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ int is_probe, chk, ret;
+ s8 lowest_idx;
+ __le16 fc = hdr->frame_control;
+ u8 *qc, tid;
+ DECLARE_MAC_BUF(mac);
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s\n", __func__);
+
+ /* allocate driver private area of tx_info */
+ tx_info->driver_data[0] = kzalloc(sizeof(*tx_info_priv), GFP_ATOMIC);
+ ASSERT(tx_info->driver_data[0] != NULL);
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+
+ sta = sta_info_get(local, hdr->addr1);
+ lowest_idx = rate_lowest_index(local, sband, sta);
+ tx_info_priv->min_rate = (sband->bitrates[lowest_idx].bitrate * 2) / 10;
+ /* lowest rate for management and multicast/broadcast frames */
+ if (!ieee80211_is_data(fc) ||
+ is_multicast_ether_addr(hdr->addr1) || !sta) {
+ sel->rate_idx = lowest_idx;
+ return;
+ }
+
+ ath_rc_priv = sta->rate_ctrl_priv;
+
+ /* Find tx rate for unicast frames */
+ ath_rate_findrate(sc, ath_rc_priv,
+ ATH_11N_TXMAXTRY, 4,
+ ATH_RC_PROBE_ALLOWED,
+ tx_info_priv->rcs,
+ &is_probe,
+ false);
+ if (is_probe)
+ sel->probe_idx = ((struct ath_tx_ratectrl *)
+ sta->rate_ctrl_priv)->probe_rate;
+
+ /* Ratecontrol sometimes returns invalid rate index */
+ if (tx_info_priv->rcs[0].rix != 0xff)
+ ath_rc_priv->prev_data_rix = tx_info_priv->rcs[0].rix;
+ else
+ tx_info_priv->rcs[0].rix = ath_rc_priv->prev_data_rix;
+
+ sel->rate_idx = tx_info_priv->rcs[0].rix;
+
+ /* Check if aggregation has to be enabled for this tid */
+
+ if (hw->conf.ht_conf.ht_supported) {
+ if (ieee80211_is_data_qos(fc)) {
+ qc = ieee80211_get_qos_ctl(hdr);
+ tid = qc[0] & 0xf;
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, hdr->addr1);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (!an) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Node not found to "
+ "init/chk TX aggr\n", __func__);
+ return;
+ }
+
+ chk = ath_tx_aggr_check(sc, an, tid);
+ if (chk == AGGR_REQUIRED) {
+ ret = ieee80211_start_tx_ba_session(hw,
+ hdr->addr1, tid);
+ if (ret)
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Unable to start tx "
+ "aggr for: %s\n",
+ __func__,
+ print_mac(mac, hdr->addr1));
+ else
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Started tx aggr for: %s\n",
+ __func__,
+ print_mac(mac, hdr->addr1));
+ } else if (chk == AGGR_EXCHANGE_PROGRESS)
+ ath_tx_aggr_resp(sc, sta, an, tid);
+ }
+ }
+}
+
+static void ath_rate_init(void *priv, void *priv_sta,
+ struct ieee80211_local *local,
+ struct sta_info *sta)
+{
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_hw *hw = local_to_hw(local);
+ struct ieee80211_conf *conf = &local->hw.conf;
+ struct ath_softc *sc = hw->priv;
+ int i, j = 0;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s\n", __func__);
+
+ sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
+ sta->txrate_idx = rate_lowest_index(local, sband, sta);
+
+ ath_setup_rates(local, sta);
+ if (conf->flags & IEEE80211_CONF_SUPPORT_HT_MODE) {
+ for (i = 0; i < MCS_SET_SIZE; i++) {
+ if (conf->ht_conf.supp_mcs_set[i/8] & (1<<(i%8)))
+ ((struct ath_rate_node *)
+ priv_sta)->neg_ht_rates.rs_rates[j++] = i;
+ if (j == ATH_RATE_MAX)
+ break;
+ }
+ ((struct ath_rate_node *)priv_sta)->neg_ht_rates.rs_nrates = j;
+ }
+ ath_rc_node_update(hw, priv_sta);
+}
+
+static void ath_rate_clear(void *priv)
+{
+ return;
+}
+
+static void *ath_rate_alloc(struct ieee80211_local *local)
+{
+ struct ieee80211_hw *hw = local_to_hw(local);
+ struct ath_softc *sc = hw->priv;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s", __func__);
+ return local->hw.priv;
+}
+
+static void ath_rate_free(void *priv)
+{
+ return;
+}
+
+static void *ath_rate_alloc_sta(void *priv, gfp_t gfp)
+{
+ struct ath_softc *sc = priv;
+ struct ath_vap *avp = sc->sc_vaps[0];
+ struct ath_rate_node *rate_priv;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s", __func__);
+ rate_priv = ath_rate_node_alloc(avp, sc->sc_rc, gfp);
+ if (!rate_priv) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s:Unable to allocate"
+ "private rate control structure", __func__);
+ return NULL;
+ }
+ ath_rc_sib_init(rate_priv);
+ return rate_priv;
+}
+
+static void ath_rate_free_sta(void *priv, void *priv_sta)
+{
+ struct ath_rate_node *rate_priv = priv_sta;
+ struct ath_softc *sc = priv;
+
+ DPRINTF(sc, ATH_DBG_RATE, "%s", __func__);
+ ath_rate_node_free(rate_priv);
+}
+
+static struct rate_control_ops ath_rate_ops = {
+ .module = NULL,
+ .name = "ath9k_rate_control",
+ .tx_status = ath_tx_status,
+ .get_rate = ath_get_rate,
+ .rate_init = ath_rate_init,
+ .clear = ath_rate_clear,
+ .alloc = ath_rate_alloc,
+ .free = ath_rate_free,
+ .alloc_sta = ath_rate_alloc_sta,
+ .free_sta = ath_rate_free_sta
+};
+
+int ath_rate_control_register(void)
+{
+ return ieee80211_rate_control_register(&ath_rate_ops);
+}
+
+void ath_rate_control_unregister(void)
+{
+ ieee80211_rate_control_unregister(&ath_rate_ops);
+}
+
--- /dev/null
+/*
+ * Copyright (c) 2004 Sam Leffler, Errno Consulting
+ * Copyright (c) 2004 Video54 Technologies, Inc.
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef RC_H
+#define RC_H
+
+#include "ath9k.h"
+/*
+ * Interface definitions for transmit rate control modules for the
+ * Atheros driver.
+ *
+ * A rate control module is responsible for choosing the transmit rate
+ * for each data frame. Management+control frames are always sent at
+ * a fixed rate.
+ *
+ * Only one module may be present at a time; the driver references
+ * rate control interfaces by symbol name. If multiple modules are
+ * to be supported we'll need to switch to a registration-based scheme
+ * as is currently done, for example, for authentication modules.
+ *
+ * An instance of the rate control module is attached to each device
+ * at attach time and detached when the device is destroyed. The module
+ * may associate data with each device and each node (station). Both
+ * sets of storage are opaque except for the size of the per-node storage
+ * which must be provided when the module is attached.
+ *
+ * The rate control module is notified for each state transition and
+ * station association/reassociation. Otherwise it is queried for a
+ * rate for each outgoing frame and provided status from each transmitted
+ * frame. Any ancillary processing is the responsibility of the module
+ * (e.g. if periodic processing is required then the module should setup
+ * it's own timer).
+ *
+ * In addition to the transmit rate for each frame the module must also
+ * indicate the number of attempts to make at the specified rate. If this
+ * number is != ATH_TXMAXTRY then an additional callback is made to setup
+ * additional transmit state. The rate control code is assumed to write
+ * this additional data directly to the transmit descriptor.
+ */
+
+struct ath_softc;
+
+#define TRUE 1
+#define FALSE 0
+
+#define ATH_RATE_MAX 30
+#define MCS_SET_SIZE 128
+
+enum ieee80211_fixed_rate_mode {
+ IEEE80211_FIXED_RATE_NONE = 0,
+ IEEE80211_FIXED_RATE_MCS = 1 /* HT rates */
+};
+
+/*
+ * Use the hal os glue code to get ms time
+ */
+#define IEEE80211_RATE_IDX_ENTRY(val, idx) (((val&(0xff<<(idx*8)))>>(idx*8)))
+
+#define SHORT_PRE 1
+#define LONG_PRE 0
+
+#define WLAN_PHY_HT_20_SS WLAN_RC_PHY_HT_20_SS
+#define WLAN_PHY_HT_20_DS WLAN_RC_PHY_HT_20_DS
+#define WLAN_PHY_HT_20_DS_HGI WLAN_RC_PHY_HT_20_DS_HGI
+#define WLAN_PHY_HT_40_SS WLAN_RC_PHY_HT_40_SS
+#define WLAN_PHY_HT_40_SS_HGI WLAN_RC_PHY_HT_40_SS_HGI
+#define WLAN_PHY_HT_40_DS WLAN_RC_PHY_HT_40_DS
+#define WLAN_PHY_HT_40_DS_HGI WLAN_RC_PHY_HT_40_DS_HGI
+
+#define WLAN_PHY_OFDM PHY_OFDM
+#define WLAN_PHY_CCK PHY_CCK
+
+#define TRUE_20 0x2
+#define TRUE_40 0x4
+#define TRUE_2040 (TRUE_20|TRUE_40)
+#define TRUE_ALL (TRUE_2040|TRUE)
+
+enum {
+ WLAN_RC_PHY_HT_20_SS = 4,
+ WLAN_RC_PHY_HT_20_DS,
+ WLAN_RC_PHY_HT_40_SS,
+ WLAN_RC_PHY_HT_40_DS,
+ WLAN_RC_PHY_HT_20_SS_HGI,
+ WLAN_RC_PHY_HT_20_DS_HGI,
+ WLAN_RC_PHY_HT_40_SS_HGI,
+ WLAN_RC_PHY_HT_40_DS_HGI,
+ WLAN_RC_PHY_MAX
+};
+
+#define WLAN_RC_PHY_DS(_phy) ((_phy == WLAN_RC_PHY_HT_20_DS) \
+ || (_phy == WLAN_RC_PHY_HT_40_DS) \
+ || (_phy == WLAN_RC_PHY_HT_20_DS_HGI) \
+ || (_phy == WLAN_RC_PHY_HT_40_DS_HGI))
+#define WLAN_RC_PHY_40(_phy) ((_phy == WLAN_RC_PHY_HT_40_SS) \
+ || (_phy == WLAN_RC_PHY_HT_40_DS) \
+ || (_phy == WLAN_RC_PHY_HT_40_SS_HGI) \
+ || (_phy == WLAN_RC_PHY_HT_40_DS_HGI))
+#define WLAN_RC_PHY_SGI(_phy) ((_phy == WLAN_RC_PHY_HT_20_SS_HGI) \
+ || (_phy == WLAN_RC_PHY_HT_20_DS_HGI) \
+ || (_phy == WLAN_RC_PHY_HT_40_SS_HGI) \
+ || (_phy == WLAN_RC_PHY_HT_40_DS_HGI))
+
+#define WLAN_RC_PHY_HT(_phy) (_phy >= WLAN_RC_PHY_HT_20_SS)
+
+/* Returns the capflag mode */
+#define WLAN_RC_CAP_MODE(capflag) (((capflag & WLAN_RC_HT_FLAG) ? \
+ (capflag & WLAN_RC_40_FLAG) ? TRUE_40 : TRUE_20 : TRUE))
+
+/* Return TRUE if flag supports HT20 && client supports HT20 or
+ * return TRUE if flag supports HT40 && client supports HT40.
+ * This is used becos some rates overlap between HT20/HT40.
+ */
+
+#define WLAN_RC_PHY_HT_VALID(flag, capflag) (((flag & TRUE_20) && !(capflag \
+ & WLAN_RC_40_FLAG)) || ((flag & TRUE_40) && \
+ (capflag & WLAN_RC_40_FLAG)))
+
+#define WLAN_RC_DS_FLAG (0x01)
+#define WLAN_RC_40_FLAG (0x02)
+#define WLAN_RC_SGI_FLAG (0x04)
+#define WLAN_RC_HT_FLAG (0x08)
+
+/* Index into the rate table */
+#define INIT_RATE_MAX_20 23
+#define INIT_RATE_MAX_40 40
+
+#define RATE_TABLE_SIZE 64
+
+/* XXX: Convert to kdoc */
+struct ath_rate_table {
+ int rate_cnt;
+ struct {
+ int valid; /* Valid for use in rate control */
+ int valid_single_stream;/* Valid for use in rate control
+ for single stream operation */
+ u8 phy; /* CCK/OFDM/TURBO/XR */
+ u32 ratekbps; /* Rate in Kbits per second */
+ u32 user_ratekbps; /* User rate in KBits per second */
+ u8 ratecode; /* rate that goes into
+ hw descriptors */
+ u8 short_preamble; /* Mask for enabling short preamble
+ in rate code for CCK */
+ u8 dot11rate; /* Value that goes into supported
+ rates info element of MLME */
+ u8 ctrl_rate; /* Index of next lower basic rate,
+ used for duration computation */
+ int8_t rssi_ack_validmin; /* Rate control related */
+ int8_t rssi_ack_deltamin; /* Rate control related */
+ u8 base_index; /* base rate index */
+ u8 cw40index; /* 40cap rate index */
+ u8 sgi_index; /* shortgi rate index */
+ u8 ht_index; /* shortgi rate index */
+ u32 max_4ms_framelen; /* Maximum frame length(bytes)
+ for 4ms tx duration */
+ } info[RATE_TABLE_SIZE];
+ u32 probe_interval; /* interval for ratectrl to
+ probe for other rates */
+ u32 rssi_reduce_interval; /* interval for ratectrl
+ to reduce RSSI */
+ u8 initial_ratemax; /* the initial ratemax value used
+ in ath_rc_sib_update() */
+};
+
+#define ATH_RC_PROBE_ALLOWED 0x00000001
+#define ATH_RC_MINRATE_LASTRATE 0x00000002
+#define ATH_RC_SHORT_PREAMBLE 0x00000004
+
+struct ath_rc_series {
+ u8 rix;
+ u8 tries;
+ u8 flags;
+ u32 max_4ms_framelen;
+};
+
+/* rcs_flags definition */
+#define ATH_RC_DS_FLAG 0x01
+#define ATH_RC_CW40_FLAG 0x02 /* CW 40 */
+#define ATH_RC_SGI_FLAG 0x04 /* Short Guard Interval */
+#define ATH_RC_HT_FLAG 0x08 /* HT */
+#define ATH_RC_RTSCTS_FLAG 0x10 /* RTS-CTS */
+
+/*
+ * State structures for new rate adaptation code
+ */
+#define MAX_TX_RATE_TBL 64
+#define MAX_TX_RATE_PHY 48
+
+struct ath_tx_ratectrl_state {
+ int8_t rssi_thres; /* required rssi for this rate (dB) */
+ u8 per; /* recent estimate of packet error rate (%) */
+};
+
+struct ath_tx_ratectrl {
+ struct ath_tx_ratectrl_state state[MAX_TX_RATE_TBL]; /* state */
+ int8_t rssi_last; /* last ack rssi */
+ int8_t rssi_last_lookup; /* last ack rssi used for lookup */
+ int8_t rssi_last_prev; /* previous last ack rssi */
+ int8_t rssi_last_prev2; /* 2nd previous last ack rssi */
+ int32_t rssi_sum_cnt; /* count of rssi_sum for averaging */
+ int32_t rssi_sum_rate; /* rate that we are averaging */
+ int32_t rssi_sum; /* running sum of rssi for averaging */
+ u32 valid_txrate_mask; /* mask of valid rates */
+ u8 rate_table_size; /* rate table size */
+ u8 rate_max; /* max rate that has recently worked */
+ u8 probe_rate; /* rate we are probing at */
+ u32 rssi_time; /* msec timestamp for last ack rssi */
+ u32 rssi_down_time; /* msec timestamp for last down step */
+ u32 probe_time; /* msec timestamp for last probe */
+ u8 hw_maxretry_pktcnt; /* num packets since we got
+ HW max retry error */
+ u8 max_valid_rate; /* maximum number of valid rate */
+ u8 valid_rate_index[MAX_TX_RATE_TBL]; /* valid rate index */
+ u32 per_down_time; /* msec timstamp for last
+ PER down step */
+
+ /* 11n state */
+ u8 valid_phy_ratecnt[WLAN_RC_PHY_MAX]; /* valid rate count */
+ u8 valid_phy_rateidx[WLAN_RC_PHY_MAX][MAX_TX_RATE_TBL];
+ u8 rc_phy_mode;
+ u8 rate_max_phy; /* Phy index for the max rate */
+ u32 rate_max_lastused; /* msec timstamp of when we
+ last used rateMaxPhy */
+ u32 probe_interval; /* interval for ratectrl to probe
+ for other rates */
+};
+
+struct ath_rateset {
+ u8 rs_nrates;
+ u8 rs_rates[ATH_RATE_MAX];
+};
+
+/* per-device state */
+struct ath_rate_softc {
+ /* phy tables that contain rate control data */
+ const void *hw_rate_table[ATH9K_MODE_MAX];
+ int fixedrix; /* -1 or index of fixed rate */
+};
+
+/* per-node state */
+struct ath_rate_node {
+ struct ath_tx_ratectrl tx_ratectrl; /* rate control state proper */
+ u32 prev_data_rix; /* rate idx of last data frame */
+
+ /* map of rate ix -> negotiated rate set ix */
+ u8 rixmap[MAX_TX_RATE_TBL];
+
+ /* map of ht rate ix -> negotiated rate set ix */
+ u8 ht_rixmap[MAX_TX_RATE_TBL];
+
+ u8 ht_cap; /* ht capabilities */
+ u8 ant_tx; /* current transmit antenna */
+
+ u8 single_stream; /* When TRUE, only single
+ stream Tx possible */
+ struct ath_rateset neg_rates; /* Negotiated rates */
+ struct ath_rateset neg_ht_rates; /* Negotiated HT rates */
+ struct ath_rate_softc *asc; /* back pointer to atheros softc */
+ struct ath_vap *avp; /* back pointer to vap */
+};
+
+/* Driver data of ieee80211_tx_info */
+struct ath_tx_info_priv {
+ struct ath_rc_series rcs[4];
+ struct ath_tx_status tx;
+ int n_frames;
+ int n_bad_frames;
+ u8 min_rate;
+};
+
+/*
+ * Attach/detach a rate control module.
+ */
+struct ath_rate_softc *ath_rate_attach(struct ath_hal *ah);
+void ath_rate_detach(struct ath_rate_softc *asc);
+
+/*
+ * Update/reset rate control state for 802.11 state transitions.
+ * Important mostly as the analog to ath_rate_newassoc when operating
+ * in station mode.
+ */
+void ath_rc_node_update(struct ieee80211_hw *hw, struct ath_rate_node *rc_priv);
+void ath_rate_newstate(struct ath_softc *sc, struct ath_vap *avp);
+
+/*
+ * Return the tx rate series.
+ */
+void ath_rate_findrate(struct ath_softc *sc, struct ath_rate_node *ath_rc_priv,
+ int num_tries, int num_rates,
+ unsigned int rcflag, struct ath_rc_series[],
+ int *is_probe, int isretry);
+/*
+ * Return rate index for given Dot11 Rate.
+ */
+u8 ath_rate_findrateix(struct ath_softc *sc,
+ u8 dot11_rate);
+
+/* Routines to register/unregister rate control algorithm */
+int ath_rate_control_register(void);
+void ath_rate_control_unregister(void);
+
+#endif /* RC_H */
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*
+ * Implementation of receive path.
+ */
+
+#include "core.h"
+
+/*
+ * Setup and link descriptors.
+ *
+ * 11N: we can no longer afford to self link the last descriptor.
+ * MAC acknowledges BA status as long as it copies frames to host
+ * buffer (or rx fifo). This can incorrectly acknowledge packets
+ * to a sender if last desc is self-linked.
+ *
+ * NOTE: Caller should hold the rxbuf lock.
+ */
+
+static void ath_rx_buf_link(struct ath_softc *sc, struct ath_buf *bf)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_desc *ds;
+ struct sk_buff *skb;
+
+ ATH_RXBUF_RESET(bf);
+
+ ds = bf->bf_desc;
+ ds->ds_link = 0; /* link to null */
+ ds->ds_data = bf->bf_buf_addr;
+
+ /* XXX For RADAR?
+ * virtual addr of the beginning of the buffer. */
+ skb = bf->bf_mpdu;
+ ASSERT(skb != NULL);
+ ds->ds_vdata = skb->data;
+
+ /* setup rx descriptors */
+ ath9k_hw_setuprxdesc(ah,
+ ds,
+ skb_tailroom(skb), /* buffer size */
+ 0);
+
+ if (sc->sc_rxlink == NULL)
+ ath9k_hw_putrxbuf(ah, bf->bf_daddr);
+ else
+ *sc->sc_rxlink = bf->bf_daddr;
+
+ sc->sc_rxlink = &ds->ds_link;
+ ath9k_hw_rxena(ah);
+}
+
+/* Process received BAR frame */
+
+static int ath_bar_rx(struct ath_softc *sc,
+ struct ath_node *an,
+ struct sk_buff *skb)
+{
+ struct ieee80211_bar *bar;
+ struct ath_arx_tid *rxtid;
+ struct sk_buff *tskb;
+ struct ath_recv_status *rx_status;
+ int tidno, index, cindex;
+ u16 seqno;
+
+ /* look at BAR contents */
+
+ bar = (struct ieee80211_bar *)skb->data;
+ tidno = (le16_to_cpu(bar->control) & IEEE80211_BAR_CTL_TID_M)
+ >> IEEE80211_BAR_CTL_TID_S;
+ seqno = le16_to_cpu(bar->start_seq_num) >> IEEE80211_SEQ_SEQ_SHIFT;
+
+ /* process BAR - indicate all pending RX frames till the BAR seqno */
+
+ rxtid = &an->an_aggr.rx.tid[tidno];
+
+ spin_lock_bh(&rxtid->tidlock);
+
+ /* get relative index */
+
+ index = ATH_BA_INDEX(rxtid->seq_next, seqno);
+
+ /* drop BAR if old sequence (index is too large) */
+
+ if ((index > rxtid->baw_size) &&
+ (index > (IEEE80211_SEQ_MAX - (rxtid->baw_size << 2))))
+ /* discard frame, ieee layer may not treat frame as a dup */
+ goto unlock_and_free;
+
+ /* complete receive processing for all pending frames upto BAR seqno */
+
+ cindex = (rxtid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
+ while ((rxtid->baw_head != rxtid->baw_tail) &&
+ (rxtid->baw_head != cindex)) {
+ tskb = rxtid->rxbuf[rxtid->baw_head].rx_wbuf;
+ rx_status = &rxtid->rxbuf[rxtid->baw_head].rx_status;
+ rxtid->rxbuf[rxtid->baw_head].rx_wbuf = NULL;
+
+ if (tskb != NULL)
+ ath_rx_subframe(an, tskb, rx_status);
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ }
+
+ /* ... and indicate rest of the frames in-order */
+
+ while (rxtid->baw_head != rxtid->baw_tail &&
+ rxtid->rxbuf[rxtid->baw_head].rx_wbuf != NULL) {
+ tskb = rxtid->rxbuf[rxtid->baw_head].rx_wbuf;
+ rx_status = &rxtid->rxbuf[rxtid->baw_head].rx_status;
+ rxtid->rxbuf[rxtid->baw_head].rx_wbuf = NULL;
+
+ ath_rx_subframe(an, tskb, rx_status);
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ }
+
+unlock_and_free:
+ spin_unlock_bh(&rxtid->tidlock);
+ /* free bar itself */
+ dev_kfree_skb(skb);
+ return IEEE80211_FTYPE_CTL;
+}
+
+/* Function to handle a subframe of aggregation when HT is enabled */
+
+static int ath_ampdu_input(struct ath_softc *sc,
+ struct ath_node *an,
+ struct sk_buff *skb,
+ struct ath_recv_status *rx_status)
+{
+ struct ieee80211_hdr *hdr;
+ struct ath_arx_tid *rxtid;
+ struct ath_rxbuf *rxbuf;
+ u8 type, subtype;
+ u16 rxseq;
+ int tid = 0, index, cindex, rxdiff;
+ __le16 fc;
+ u8 *qc;
+
+ hdr = (struct ieee80211_hdr *)skb->data;
+ fc = hdr->frame_control;
+
+ /* collect stats of frames with non-zero version */
+
+ if ((le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_VERS) != 0) {
+ dev_kfree_skb(skb);
+ return -1;
+ }
+
+ type = le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_FTYPE;
+ subtype = le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_STYPE;
+
+ if (ieee80211_is_back_req(fc))
+ return ath_bar_rx(sc, an, skb);
+
+ /* special aggregate processing only for qos unicast data frames */
+
+ if (!ieee80211_is_data(fc) ||
+ !ieee80211_is_data_qos(fc) ||
+ is_multicast_ether_addr(hdr->addr1))
+ return ath_rx_subframe(an, skb, rx_status);
+
+ /* lookup rx tid state */
+
+ if (ieee80211_is_data_qos(fc)) {
+ qc = ieee80211_get_qos_ctl(hdr);
+ tid = qc[0] & 0xf;
+ }
+
+ if (sc->sc_opmode == ATH9K_M_STA) {
+ /* Drop the frame not belonging to me. */
+ if (memcmp(hdr->addr1, sc->sc_myaddr, ETH_ALEN)) {
+ dev_kfree_skb(skb);
+ return -1;
+ }
+ }
+
+ rxtid = &an->an_aggr.rx.tid[tid];
+
+ spin_lock(&rxtid->tidlock);
+
+ rxdiff = (rxtid->baw_tail - rxtid->baw_head) &
+ (ATH_TID_MAX_BUFS - 1);
+
+ /*
+ * If the ADDBA exchange has not been completed by the source,
+ * process via legacy path (i.e. no reordering buffer is needed)
+ */
+ if (!rxtid->addba_exchangecomplete) {
+ spin_unlock(&rxtid->tidlock);
+ return ath_rx_subframe(an, skb, rx_status);
+ }
+
+ /* extract sequence number from recvd frame */
+
+ rxseq = le16_to_cpu(hdr->seq_ctrl) >> IEEE80211_SEQ_SEQ_SHIFT;
+
+ if (rxtid->seq_reset) {
+ rxtid->seq_reset = 0;
+ rxtid->seq_next = rxseq;
+ }
+
+ index = ATH_BA_INDEX(rxtid->seq_next, rxseq);
+
+ /* drop frame if old sequence (index is too large) */
+
+ if (index > (IEEE80211_SEQ_MAX - (rxtid->baw_size << 2))) {
+ /* discard frame, ieee layer may not treat frame as a dup */
+ spin_unlock(&rxtid->tidlock);
+ dev_kfree_skb(skb);
+ return IEEE80211_FTYPE_DATA;
+ }
+
+ /* sequence number is beyond block-ack window */
+
+ if (index >= rxtid->baw_size) {
+
+ /* complete receive processing for all pending frames */
+
+ while (index >= rxtid->baw_size) {
+
+ rxbuf = rxtid->rxbuf + rxtid->baw_head;
+
+ if (rxbuf->rx_wbuf != NULL) {
+ ath_rx_subframe(an, rxbuf->rx_wbuf,
+ &rxbuf->rx_status);
+ rxbuf->rx_wbuf = NULL;
+ }
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+
+ index--;
+ }
+ }
+
+ /* add buffer to the recv ba window */
+
+ cindex = (rxtid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
+ rxbuf = rxtid->rxbuf + cindex;
+
+ if (rxbuf->rx_wbuf != NULL) {
+ spin_unlock(&rxtid->tidlock);
+ /* duplicate frame */
+ dev_kfree_skb(skb);
+ return IEEE80211_FTYPE_DATA;
+ }
+
+ rxbuf->rx_wbuf = skb;
+ rxbuf->rx_time = get_timestamp();
+ rxbuf->rx_status = *rx_status;
+
+ /* advance tail if sequence received is newer
+ * than any received so far */
+
+ if (index >= rxdiff) {
+ rxtid->baw_tail = cindex;
+ INCR(rxtid->baw_tail, ATH_TID_MAX_BUFS);
+ }
+
+ /* indicate all in-order received frames */
+
+ while (rxtid->baw_head != rxtid->baw_tail) {
+ rxbuf = rxtid->rxbuf + rxtid->baw_head;
+ if (!rxbuf->rx_wbuf)
+ break;
+
+ ath_rx_subframe(an, rxbuf->rx_wbuf, &rxbuf->rx_status);
+ rxbuf->rx_wbuf = NULL;
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ }
+
+ /*
+ * start a timer to flush all received frames if there are pending
+ * receive frames
+ */
+ if (rxtid->baw_head != rxtid->baw_tail)
+ mod_timer(&rxtid->timer, ATH_RX_TIMEOUT);
+ else
+ del_timer_sync(&rxtid->timer);
+
+ spin_unlock(&rxtid->tidlock);
+ return IEEE80211_FTYPE_DATA;
+}
+
+/* Timer to flush all received sub-frames */
+
+static void ath_rx_timer(unsigned long data)
+{
+ struct ath_arx_tid *rxtid = (struct ath_arx_tid *)data;
+ struct ath_node *an = rxtid->an;
+ struct ath_rxbuf *rxbuf;
+ int nosched;
+
+ spin_lock_bh(&rxtid->tidlock);
+ while (rxtid->baw_head != rxtid->baw_tail) {
+ rxbuf = rxtid->rxbuf + rxtid->baw_head;
+ if (!rxbuf->rx_wbuf) {
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ continue;
+ }
+
+ /*
+ * Stop if the next one is a very recent frame.
+ *
+ * Call get_timestamp in every iteration to protect against the
+ * case in which a new frame is received while we are executing
+ * this function. Using a timestamp obtained before entering
+ * the loop could lead to a very large time interval
+ * (a negative value typecast to unsigned), breaking the
+ * function's logic.
+ */
+ if ((get_timestamp() - rxbuf->rx_time) <
+ (ATH_RX_TIMEOUT * HZ / 1000))
+ break;
+
+ ath_rx_subframe(an, rxbuf->rx_wbuf,
+ &rxbuf->rx_status);
+ rxbuf->rx_wbuf = NULL;
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ }
+
+ /*
+ * start a timer to flush all received frames if there are pending
+ * receive frames
+ */
+ if (rxtid->baw_head != rxtid->baw_tail)
+ nosched = 0;
+ else
+ nosched = 1; /* no need to re-arm the timer again */
+
+ spin_unlock_bh(&rxtid->tidlock);
+}
+
+/* Free all pending sub-frames in the re-ordering buffer */
+
+static void ath_rx_flush_tid(struct ath_softc *sc,
+ struct ath_arx_tid *rxtid, int drop)
+{
+ struct ath_rxbuf *rxbuf;
+
+ spin_lock_bh(&rxtid->tidlock);
+ while (rxtid->baw_head != rxtid->baw_tail) {
+ rxbuf = rxtid->rxbuf + rxtid->baw_head;
+ if (!rxbuf->rx_wbuf) {
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ continue;
+ }
+
+ if (drop)
+ dev_kfree_skb(rxbuf->rx_wbuf);
+ else
+ ath_rx_subframe(rxtid->an,
+ rxbuf->rx_wbuf,
+ &rxbuf->rx_status);
+
+ rxbuf->rx_wbuf = NULL;
+
+ INCR(rxtid->baw_head, ATH_TID_MAX_BUFS);
+ INCR(rxtid->seq_next, IEEE80211_SEQ_MAX);
+ }
+ spin_unlock_bh(&rxtid->tidlock);
+}
+
+static struct sk_buff *ath_rxbuf_alloc(struct ath_softc *sc,
+ u32 len)
+{
+ struct sk_buff *skb;
+ u32 off;
+
+ /*
+ * Cache-line-align. This is important (for the
+ * 5210 at least) as not doing so causes bogus data
+ * in rx'd frames.
+ */
+
+ skb = dev_alloc_skb(len + sc->sc_cachelsz - 1);
+ if (skb != NULL) {
+ off = ((unsigned long) skb->data) % sc->sc_cachelsz;
+ if (off != 0)
+ skb_reserve(skb, sc->sc_cachelsz - off);
+ } else {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: skbuff alloc of size %u failed\n",
+ __func__, len);
+ return NULL;
+ }
+
+ return skb;
+}
+
+static void ath_rx_requeue(struct ath_softc *sc, struct sk_buff *skb)
+{
+ struct ath_buf *bf = ATH_RX_CONTEXT(skb)->ctx_rxbuf;
+
+ ASSERT(bf != NULL);
+
+ spin_lock_bh(&sc->sc_rxbuflock);
+ if (bf->bf_status & ATH_BUFSTATUS_STALE) {
+ /*
+ * This buffer is still held for hw acess.
+ * Mark it as free to be re-queued it later.
+ */
+ bf->bf_status |= ATH_BUFSTATUS_FREE;
+ } else {
+ /* XXX: we probably never enter here, remove after
+ * verification */
+ list_add_tail(&bf->list, &sc->sc_rxbuf);
+ ath_rx_buf_link(sc, bf);
+ }
+ spin_unlock_bh(&sc->sc_rxbuflock);
+}
+
+/*
+ * The skb indicated to upper stack won't be returned to us.
+ * So we have to allocate a new one and queue it by ourselves.
+ */
+static int ath_rx_indicate(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_recv_status *status,
+ u16 keyix)
+{
+ struct ath_buf *bf = ATH_RX_CONTEXT(skb)->ctx_rxbuf;
+ struct sk_buff *nskb;
+ int type;
+
+ /* indicate frame to the stack, which will free the old skb. */
+ type = ath__rx_indicate(sc, skb, status, keyix);
+
+ /* allocate a new skb and queue it to for H/W processing */
+ nskb = ath_rxbuf_alloc(sc, sc->sc_rxbufsize);
+ if (nskb != NULL) {
+ bf->bf_mpdu = nskb;
+ bf->bf_buf_addr = ath_skb_map_single(sc,
+ nskb,
+ PCI_DMA_FROMDEVICE,
+ /* XXX: Remove get_dma_mem_context() */
+ get_dma_mem_context(bf, bf_dmacontext));
+ ATH_RX_CONTEXT(nskb)->ctx_rxbuf = bf;
+
+ /* queue the new wbuf to H/W */
+ ath_rx_requeue(sc, nskb);
+ }
+
+ return type;
+}
+
+static void ath_opmode_init(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u32 rfilt, mfilt[2];
+
+ /* configure rx filter */
+ rfilt = ath_calcrxfilter(sc);
+ ath9k_hw_setrxfilter(ah, rfilt);
+
+ /* configure bssid mask */
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_BSSIDMASK)
+ ath9k_hw_setbssidmask(ah, sc->sc_bssidmask);
+
+ /* configure operational mode */
+ ath9k_hw_setopmode(ah);
+
+ /* Handle any link-level address change. */
+ ath9k_hw_setmac(ah, sc->sc_myaddr);
+
+ /* calculate and install multicast filter */
+ mfilt[0] = mfilt[1] = ~0;
+
+ ath9k_hw_setmcastfilter(ah, mfilt[0], mfilt[1]);
+ DPRINTF(sc, ATH_DBG_CONFIG ,
+ "%s: RX filter 0x%x, MC filter %08x:%08x\n",
+ __func__, rfilt, mfilt[0], mfilt[1]);
+}
+
+int ath_rx_init(struct ath_softc *sc, int nbufs)
+{
+ struct sk_buff *skb;
+ struct ath_buf *bf;
+ int error = 0;
+
+ do {
+ spin_lock_init(&sc->sc_rxflushlock);
+ sc->sc_rxflush = 0;
+ spin_lock_init(&sc->sc_rxbuflock);
+
+ /*
+ * Cisco's VPN software requires that drivers be able to
+ * receive encapsulated frames that are larger than the MTU.
+ * Since we can't be sure how large a frame we'll get, setup
+ * to handle the larges on possible.
+ */
+ sc->sc_rxbufsize = roundup(IEEE80211_MAX_MPDU_LEN,
+ min(sc->sc_cachelsz,
+ (u16)64));
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: cachelsz %u rxbufsize %u\n",
+ __func__, sc->sc_cachelsz, sc->sc_rxbufsize);
+
+ /* Initialize rx descriptors */
+
+ error = ath_descdma_setup(sc, &sc->sc_rxdma, &sc->sc_rxbuf,
+ "rx", nbufs, 1);
+ if (error != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: failed to allocate rx descriptors: %d\n",
+ __func__, error);
+ break;
+ }
+
+ /* Pre-allocate a wbuf for each rx buffer */
+
+ list_for_each_entry(bf, &sc->sc_rxbuf, list) {
+ skb = ath_rxbuf_alloc(sc, sc->sc_rxbufsize);
+ if (skb == NULL) {
+ error = -ENOMEM;
+ break;
+ }
+
+ bf->bf_mpdu = skb;
+ bf->bf_buf_addr =
+ ath_skb_map_single(sc, skb, PCI_DMA_FROMDEVICE,
+ get_dma_mem_context(bf, bf_dmacontext));
+ ATH_RX_CONTEXT(skb)->ctx_rxbuf = bf;
+ }
+ sc->sc_rxlink = NULL;
+
+ } while (0);
+
+ if (error)
+ ath_rx_cleanup(sc);
+
+ return error;
+}
+
+/* Reclaim all rx queue resources */
+
+void ath_rx_cleanup(struct ath_softc *sc)
+{
+ struct sk_buff *skb;
+ struct ath_buf *bf;
+
+ list_for_each_entry(bf, &sc->sc_rxbuf, list) {
+ skb = bf->bf_mpdu;
+ if (skb)
+ dev_kfree_skb(skb);
+ }
+
+ /* cleanup rx descriptors */
+
+ if (sc->sc_rxdma.dd_desc_len != 0)
+ ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
+}
+
+/*
+ * Calculate the receive filter according to the
+ * operating mode and state:
+ *
+ * o always accept unicast, broadcast, and multicast traffic
+ * o maintain current state of phy error reception (the hal
+ * may enable phy error frames for noise immunity work)
+ * o probe request frames are accepted only when operating in
+ * hostap, adhoc, or monitor modes
+ * o enable promiscuous mode according to the interface state
+ * o accept beacons:
+ * - when operating in adhoc mode so the 802.11 layer creates
+ * node table entries for peers,
+ * - when operating in station mode for collecting rssi data when
+ * the station is otherwise quiet, or
+ * - when operating as a repeater so we see repeater-sta beacons
+ * - when scanning
+ */
+
+u32 ath_calcrxfilter(struct ath_softc *sc)
+{
+#define RX_FILTER_PRESERVE (ATH9K_RX_FILTER_PHYERR | ATH9K_RX_FILTER_PHYRADAR)
+ u32 rfilt;
+
+ rfilt = (ath9k_hw_getrxfilter(sc->sc_ah) & RX_FILTER_PRESERVE)
+ | ATH9K_RX_FILTER_UCAST | ATH9K_RX_FILTER_BCAST
+ | ATH9K_RX_FILTER_MCAST;
+
+ /* If not a STA, enable processing of Probe Requests */
+ if (sc->sc_opmode != ATH9K_M_STA)
+ rfilt |= ATH9K_RX_FILTER_PROBEREQ;
+
+ /* Can't set HOSTAP into promiscous mode */
+ if (sc->sc_opmode == ATH9K_M_MONITOR) {
+ rfilt |= ATH9K_RX_FILTER_PROM;
+ /* ??? To prevent from sending ACK */
+ rfilt &= ~ATH9K_RX_FILTER_UCAST;
+ }
+
+ if (sc->sc_opmode == ATH9K_M_STA || sc->sc_opmode == ATH9K_M_IBSS ||
+ sc->sc_scanning)
+ rfilt |= ATH9K_RX_FILTER_BEACON;
+
+ /* If in HOSTAP mode, want to enable reception of PSPOLL frames
+ & beacon frames */
+ if (sc->sc_opmode == ATH9K_M_HOSTAP)
+ rfilt |= (ATH9K_RX_FILTER_BEACON | ATH9K_RX_FILTER_PSPOLL);
+ return rfilt;
+#undef RX_FILTER_PRESERVE
+}
+
+/* Enable the receive h/w following a reset. */
+
+int ath_startrecv(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf, *tbf;
+
+ spin_lock_bh(&sc->sc_rxbuflock);
+ if (list_empty(&sc->sc_rxbuf))
+ goto start_recv;
+
+ sc->sc_rxlink = NULL;
+ list_for_each_entry_safe(bf, tbf, &sc->sc_rxbuf, list) {
+ if (bf->bf_status & ATH_BUFSTATUS_STALE) {
+ /* restarting h/w, no need for holding descriptors */
+ bf->bf_status &= ~ATH_BUFSTATUS_STALE;
+ /*
+ * Upper layer may not be done with the frame yet so
+ * we can't just re-queue it to hardware. Remove it
+ * from h/w queue. It'll be re-queued when upper layer
+ * returns the frame and ath_rx_requeue_mpdu is called.
+ */
+ if (!(bf->bf_status & ATH_BUFSTATUS_FREE)) {
+ list_del(&bf->list);
+ continue;
+ }
+ }
+ /* chain descriptors */
+ ath_rx_buf_link(sc, bf);
+ }
+
+ /* We could have deleted elements so the list may be empty now */
+ if (list_empty(&sc->sc_rxbuf))
+ goto start_recv;
+
+ bf = list_first_entry(&sc->sc_rxbuf, struct ath_buf, list);
+ ath9k_hw_putrxbuf(ah, bf->bf_daddr);
+ ath9k_hw_rxena(ah); /* enable recv descriptors */
+
+start_recv:
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ ath_opmode_init(sc); /* set filters, etc. */
+ ath9k_hw_startpcureceive(ah); /* re-enable PCU/DMA engine */
+ return 0;
+}
+
+/* Disable the receive h/w in preparation for a reset. */
+
+bool ath_stoprecv(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u64 tsf;
+ bool stopped;
+
+ ath9k_hw_stoppcurecv(ah); /* disable PCU */
+ ath9k_hw_setrxfilter(ah, 0); /* clear recv filter */
+ stopped = ath9k_hw_stopdmarecv(ah); /* disable DMA engine */
+ mdelay(3); /* 3ms is long enough for 1 frame */
+ tsf = ath9k_hw_gettsf64(ah);
+ sc->sc_rxlink = NULL; /* just in case */
+ return stopped;
+}
+
+/* Flush receive queue */
+
+void ath_flushrecv(struct ath_softc *sc)
+{
+ /*
+ * ath_rx_tasklet may be used to handle rx interrupt and flush receive
+ * queue at the same time. Use a lock to serialize the access of rx
+ * queue.
+ * ath_rx_tasklet cannot hold the spinlock while indicating packets.
+ * Instead, do not claim the spinlock but check for a flush in
+ * progress (see references to sc_rxflush)
+ */
+ spin_lock_bh(&sc->sc_rxflushlock);
+ sc->sc_rxflush = 1;
+
+ ath_rx_tasklet(sc, 1);
+
+ sc->sc_rxflush = 0;
+ spin_unlock_bh(&sc->sc_rxflushlock);
+}
+
+/* Process an individual frame */
+
+int ath_rx_input(struct ath_softc *sc,
+ struct ath_node *an,
+ int is_ampdu,
+ struct sk_buff *skb,
+ struct ath_recv_status *rx_status,
+ enum ATH_RX_TYPE *status)
+{
+ if (is_ampdu && sc->sc_rxaggr) {
+ *status = ATH_RX_CONSUMED;
+ return ath_ampdu_input(sc, an, skb, rx_status);
+ } else {
+ *status = ATH_RX_NON_CONSUMED;
+ return -1;
+ }
+}
+
+/* Process receive queue, as well as LED, etc. */
+
+int ath_rx_tasklet(struct ath_softc *sc, int flush)
+{
+#define PA2DESC(_sc, _pa) \
+ ((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
+ ((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
+
+ struct ath_buf *bf, *bf_held = NULL;
+ struct ath_desc *ds;
+ struct ieee80211_hdr *hdr;
+ struct sk_buff *skb = NULL;
+ struct ath_recv_status rx_status;
+ struct ath_hal *ah = sc->sc_ah;
+ int type, rx_processed = 0;
+ u32 phyerr;
+ u8 chainreset = 0;
+ int retval;
+ __le16 fc;
+
+ do {
+ /* If handling rx interrupt and flush is in progress => exit */
+ if (sc->sc_rxflush && (flush == 0))
+ break;
+
+ spin_lock_bh(&sc->sc_rxbuflock);
+ if (list_empty(&sc->sc_rxbuf)) {
+ sc->sc_rxlink = NULL;
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ break;
+ }
+
+ bf = list_first_entry(&sc->sc_rxbuf, struct ath_buf, list);
+
+ /*
+ * There is a race condition that BH gets scheduled after sw
+ * writes RxE and before hw re-load the last descriptor to get
+ * the newly chained one. Software must keep the last DONE
+ * descriptor as a holding descriptor - software does so by
+ * marking it with the STALE flag.
+ */
+ if (bf->bf_status & ATH_BUFSTATUS_STALE) {
+ bf_held = bf;
+ if (list_is_last(&bf_held->list, &sc->sc_rxbuf)) {
+ /*
+ * The holding descriptor is the last
+ * descriptor in queue. It's safe to
+ * remove the last holding descriptor
+ * in BH context.
+ */
+ list_del(&bf_held->list);
+ bf_held->bf_status &= ~ATH_BUFSTATUS_STALE;
+ sc->sc_rxlink = NULL;
+
+ if (bf_held->bf_status & ATH_BUFSTATUS_FREE) {
+ list_add_tail(&bf_held->list,
+ &sc->sc_rxbuf);
+ ath_rx_buf_link(sc, bf_held);
+ }
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ break;
+ }
+ bf = list_entry(bf->list.next, struct ath_buf, list);
+ }
+
+ ds = bf->bf_desc;
+ ++rx_processed;
+
+ /*
+ * Must provide the virtual address of the current
+ * descriptor, the physical address, and the virtual
+ * address of the next descriptor in the h/w chain.
+ * This allows the HAL to look ahead to see if the
+ * hardware is done with a descriptor by checking the
+ * done bit in the following descriptor and the address
+ * of the current descriptor the DMA engine is working
+ * on. All this is necessary because of our use of
+ * a self-linked list to avoid rx overruns.
+ */
+ retval = ath9k_hw_rxprocdesc(ah,
+ ds,
+ bf->bf_daddr,
+ PA2DESC(sc, ds->ds_link),
+ 0);
+ if (retval == -EINPROGRESS) {
+ struct ath_buf *tbf;
+ struct ath_desc *tds;
+
+ if (list_is_last(&bf->list, &sc->sc_rxbuf)) {
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ break;
+ }
+
+ tbf = list_entry(bf->list.next, struct ath_buf, list);
+
+ /*
+ * On some hardware the descriptor status words could
+ * get corrupted, including the done bit. Because of
+ * this, check if the next descriptor's done bit is
+ * set or not.
+ *
+ * If the next descriptor's done bit is set, the current
+ * descriptor has been corrupted. Force s/w to discard
+ * this descriptor and continue...
+ */
+
+ tds = tbf->bf_desc;
+ retval = ath9k_hw_rxprocdesc(ah,
+ tds, tbf->bf_daddr,
+ PA2DESC(sc, tds->ds_link), 0);
+ if (retval == -EINPROGRESS) {
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ break;
+ }
+ }
+
+ /* XXX: we do not support frames spanning
+ * multiple descriptors */
+ bf->bf_status |= ATH_BUFSTATUS_DONE;
+
+ skb = bf->bf_mpdu;
+ if (skb == NULL) { /* XXX ??? can this happen */
+ spin_unlock_bh(&sc->sc_rxbuflock);
+ continue;
+ }
+ /*
+ * Now we know it's a completed frame, we can indicate the
+ * frame. Remove the previous holding descriptor and leave
+ * this one in the queue as the new holding descriptor.
+ */
+ if (bf_held) {
+ list_del(&bf_held->list);
+ bf_held->bf_status &= ~ATH_BUFSTATUS_STALE;
+ if (bf_held->bf_status & ATH_BUFSTATUS_FREE) {
+ list_add_tail(&bf_held->list, &sc->sc_rxbuf);
+ /* try to requeue this descriptor */
+ ath_rx_buf_link(sc, bf_held);
+ }
+ }
+
+ bf->bf_status |= ATH_BUFSTATUS_STALE;
+ bf_held = bf;
+ /*
+ * Release the lock here in case ieee80211_input() return
+ * the frame immediately by calling ath_rx_mpdu_requeue().
+ */
+ spin_unlock_bh(&sc->sc_rxbuflock);
+
+ if (flush) {
+ /*
+ * If we're asked to flush receive queue, directly
+ * chain it back at the queue without processing it.
+ */
+ goto rx_next;
+ }
+
+ hdr = (struct ieee80211_hdr *)skb->data;
+ fc = hdr->frame_control;
+ memzero(&rx_status, sizeof(struct ath_recv_status));
+
+ if (ds->ds_rxstat.rs_more) {
+ /*
+ * Frame spans multiple descriptors; this
+ * cannot happen yet as we don't support
+ * jumbograms. If not in monitor mode,
+ * discard the frame.
+ */
+#ifndef ERROR_FRAMES
+ /*
+ * Enable this if you want to see
+ * error frames in Monitor mode.
+ */
+ if (sc->sc_opmode != ATH9K_M_MONITOR)
+ goto rx_next;
+#endif
+ /* fall thru for monitor mode handling... */
+ } else if (ds->ds_rxstat.rs_status != 0) {
+ if (ds->ds_rxstat.rs_status & ATH9K_RXERR_CRC)
+ rx_status.flags |= ATH_RX_FCS_ERROR;
+ if (ds->ds_rxstat.rs_status & ATH9K_RXERR_PHY) {
+ phyerr = ds->ds_rxstat.rs_phyerr & 0x1f;
+ goto rx_next;
+ }
+
+ if (ds->ds_rxstat.rs_status & ATH9K_RXERR_DECRYPT) {
+ /*
+ * Decrypt error. We only mark packet status
+ * here and always push up the frame up to let
+ * mac80211 handle the actual error case, be
+ * it no decryption key or real decryption
+ * error. This let us keep statistics there.
+ */
+ rx_status.flags |= ATH_RX_DECRYPT_ERROR;
+ } else if (ds->ds_rxstat.rs_status & ATH9K_RXERR_MIC) {
+ /*
+ * Demic error. We only mark frame status here
+ * and always push up the frame up to let
+ * mac80211 handle the actual error case. This
+ * let us keep statistics there. Hardware may
+ * post a false-positive MIC error.
+ */
+ if (ieee80211_is_ctl(fc))
+ /*
+ * Sometimes, we get invalid
+ * MIC failures on valid control frames.
+ * Remove these mic errors.
+ */
+ ds->ds_rxstat.rs_status &=
+ ~ATH9K_RXERR_MIC;
+ else
+ rx_status.flags |= ATH_RX_MIC_ERROR;
+ }
+ /*
+ * Reject error frames with the exception of
+ * decryption and MIC failures. For monitor mode,
+ * we also ignore the CRC error.
+ */
+ if (sc->sc_opmode == ATH9K_M_MONITOR) {
+ if (ds->ds_rxstat.rs_status &
+ ~(ATH9K_RXERR_DECRYPT | ATH9K_RXERR_MIC |
+ ATH9K_RXERR_CRC))
+ goto rx_next;
+ } else {
+ if (ds->ds_rxstat.rs_status &
+ ~(ATH9K_RXERR_DECRYPT | ATH9K_RXERR_MIC)) {
+ goto rx_next;
+ }
+ }
+ }
+ /*
+ * The status portion of the descriptor could get corrupted.
+ */
+ if (sc->sc_rxbufsize < ds->ds_rxstat.rs_datalen)
+ goto rx_next;
+ /*
+ * Sync and unmap the frame. At this point we're
+ * committed to passing the sk_buff somewhere so
+ * clear buf_skb; this means a new sk_buff must be
+ * allocated when the rx descriptor is setup again
+ * to receive another frame.
+ */
+ skb_put(skb, ds->ds_rxstat.rs_datalen);
+ skb->protocol = cpu_to_be16(ETH_P_CONTROL);
+ rx_status.tsf = ath_extend_tsf(sc, ds->ds_rxstat.rs_tstamp);
+ rx_status.rateieee =
+ sc->sc_hwmap[ds->ds_rxstat.rs_rate].ieeerate;
+ rx_status.rateKbps =
+ sc->sc_hwmap[ds->ds_rxstat.rs_rate].rateKbps;
+ rx_status.ratecode = ds->ds_rxstat.rs_rate;
+
+ /* HT rate */
+ if (rx_status.ratecode & 0x80) {
+ /* TODO - add table to avoid division */
+ if (ds->ds_rxstat.rs_flags & ATH9K_RX_2040) {
+ rx_status.flags |= ATH_RX_40MHZ;
+ rx_status.rateKbps =
+ (rx_status.rateKbps * 27) / 13;
+ }
+ if (ds->ds_rxstat.rs_flags & ATH9K_RX_GI)
+ rx_status.rateKbps =
+ (rx_status.rateKbps * 10) / 9;
+ else
+ rx_status.flags |= ATH_RX_SHORT_GI;
+ }
+
+ /* sc->sc_noise_floor is only available when the station
+ attaches to an AP, so we use a default value
+ if we are not yet attached. */
+
+ /* XXX we should use either sc->sc_noise_floor or
+ * ath_hal_getChanNoise(ah, &sc->sc_curchan)
+ * to calculate the noise floor.
+ * However, the value returned by ath_hal_getChanNoise
+ * seems to be incorrect (-31dBm on the last test),
+ * so we will use a hard-coded value until we
+ * figure out what is going on.
+ */
+ rx_status.abs_rssi =
+ ds->ds_rxstat.rs_rssi + ATH_DEFAULT_NOISE_FLOOR;
+
+ pci_dma_sync_single_for_cpu(sc->pdev,
+ bf->bf_buf_addr,
+ skb_tailroom(skb),
+ PCI_DMA_FROMDEVICE);
+ pci_unmap_single(sc->pdev,
+ bf->bf_buf_addr,
+ sc->sc_rxbufsize,
+ PCI_DMA_FROMDEVICE);
+
+ /* XXX: Ah! make me more readable, use a helper */
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) {
+ if (ds->ds_rxstat.rs_moreaggr == 0) {
+ rx_status.rssictl[0] =
+ ds->ds_rxstat.rs_rssi_ctl0;
+ rx_status.rssictl[1] =
+ ds->ds_rxstat.rs_rssi_ctl1;
+ rx_status.rssictl[2] =
+ ds->ds_rxstat.rs_rssi_ctl2;
+ rx_status.rssi = ds->ds_rxstat.rs_rssi;
+ if (ds->ds_rxstat.rs_flags & ATH9K_RX_2040) {
+ rx_status.rssiextn[0] =
+ ds->ds_rxstat.rs_rssi_ext0;
+ rx_status.rssiextn[1] =
+ ds->ds_rxstat.rs_rssi_ext1;
+ rx_status.rssiextn[2] =
+ ds->ds_rxstat.rs_rssi_ext2;
+ rx_status.flags |=
+ ATH_RX_RSSI_EXTN_VALID;
+ }
+ rx_status.flags |= ATH_RX_RSSI_VALID |
+ ATH_RX_CHAIN_RSSI_VALID;
+ }
+ } else {
+ /*
+ * Need to insert the "combined" rssi into the
+ * status structure for upper layer processing
+ */
+ rx_status.rssi = ds->ds_rxstat.rs_rssi;
+ rx_status.flags |= ATH_RX_RSSI_VALID;
+ }
+
+ /* Pass frames up to the stack. */
+
+ type = ath_rx_indicate(sc, skb,
+ &rx_status, ds->ds_rxstat.rs_keyix);
+
+ /*
+ * change the default rx antenna if rx diversity chooses the
+ * other antenna 3 times in a row.
+ */
+ if (sc->sc_defant != ds->ds_rxstat.rs_antenna) {
+ if (++sc->sc_rxotherant >= 3)
+ ath_setdefantenna(sc,
+ ds->ds_rxstat.rs_antenna);
+ } else {
+ sc->sc_rxotherant = 0;
+ }
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ if ((rx_status.flags & ATH_RX_RSSI_VALID) &&
+ ieee80211_is_beacon(fc)) {
+ ath_slow_ant_div(&sc->sc_antdiv, hdr, &ds->ds_rxstat);
+ }
+#endif
+ /*
+ * For frames successfully indicated, the buffer will be
+ * returned to us by upper layers by calling
+ * ath_rx_mpdu_requeue, either synchronusly or asynchronously.
+ * So we don't want to do it here in this loop.
+ */
+ continue;
+
+rx_next:
+ bf->bf_status |= ATH_BUFSTATUS_FREE;
+ } while (TRUE);
+
+ if (chainreset) {
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: Reset rx chain mask. "
+ "Do internal reset\n", __func__);
+ ASSERT(flush == 0);
+ ath_internal_reset(sc);
+ }
+
+ return 0;
+#undef PA2DESC
+}
+
+/* Process ADDBA request in per-TID data structure */
+
+int ath_rx_aggr_start(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid,
+ u16 *ssn)
+{
+ struct ath_arx_tid *rxtid;
+ struct ath_node *an;
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_supported_band *sband;
+ u16 buffersize = 0;
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, (u8 *) addr);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (!an) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Node not found to initialize RX aggregation\n",
+ __func__);
+ return -1;
+ }
+
+ sband = hw->wiphy->bands[hw->conf.channel->band];
+ buffersize = IEEE80211_MIN_AMPDU_BUF <<
+ sband->ht_info.ampdu_factor; /* FIXME */
+
+ rxtid = &an->an_aggr.rx.tid[tid];
+
+ spin_lock_bh(&rxtid->tidlock);
+ if (sc->sc_rxaggr) {
+ /* Allow aggregation reception
+ * Adjust rx BA window size. Peer might indicate a
+ * zero buffer size for a _dont_care_ condition.
+ */
+ if (buffersize)
+ rxtid->baw_size = min(buffersize, rxtid->baw_size);
+
+ /* set rx sequence number */
+ rxtid->seq_next = *ssn;
+
+ /* Allocate the receive buffers for this TID */
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Allcating rxbuffer for TID %d\n", __func__, tid);
+
+ if (rxtid->rxbuf == NULL) {
+ /*
+ * If the rxbuff is not NULL at this point, we *probably*
+ * already allocated the buffer on a previous ADDBA,
+ * and this is a subsequent ADDBA that got through.
+ * Don't allocate, but use the value in the pointer,
+ * we zero it out when we de-allocate.
+ */
+ rxtid->rxbuf = kmalloc(ATH_TID_MAX_BUFS *
+ sizeof(struct ath_rxbuf), GFP_ATOMIC);
+ }
+ if (rxtid->rxbuf == NULL) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Unable to allocate RX buffer, "
+ "refusing ADDBA\n", __func__);
+ } else {
+ /* Ensure the memory is zeroed out (all internal
+ * pointers are null) */
+ memzero(rxtid->rxbuf, ATH_TID_MAX_BUFS *
+ sizeof(struct ath_rxbuf));
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Allocated @%p\n", __func__, rxtid->rxbuf);
+
+ /* Allow aggregation reception */
+ rxtid->addba_exchangecomplete = 1;
+ }
+ }
+ spin_unlock_bh(&rxtid->tidlock);
+
+ return 0;
+}
+
+/* Process DELBA */
+
+int ath_rx_aggr_stop(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid)
+{
+ struct ath_node *an;
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, (u8 *) addr);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (!an) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: RX aggr stop for non-existent node\n", __func__);
+ return -1;
+ }
+
+ ath_rx_aggr_teardown(sc, an, tid);
+ return 0;
+}
+
+/* Rx aggregation tear down */
+
+void ath_rx_aggr_teardown(struct ath_softc *sc,
+ struct ath_node *an, u8 tid)
+{
+ struct ath_arx_tid *rxtid = &an->an_aggr.rx.tid[tid];
+
+ if (!rxtid->addba_exchangecomplete)
+ return;
+
+ del_timer_sync(&rxtid->timer);
+ ath_rx_flush_tid(sc, rxtid, 0);
+ rxtid->addba_exchangecomplete = 0;
+
+ /* De-allocate the receive buffer array allocated when addba started */
+
+ if (rxtid->rxbuf) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Deallocating TID %d rxbuff @%p\n",
+ __func__, tid, rxtid->rxbuf);
+ kfree(rxtid->rxbuf);
+
+ /* Set pointer to null to avoid reuse*/
+ rxtid->rxbuf = NULL;
+ }
+}
+
+/* Initialize per-node receive state */
+
+void ath_rx_node_init(struct ath_softc *sc, struct ath_node *an)
+{
+ if (sc->sc_rxaggr) {
+ struct ath_arx_tid *rxtid;
+ int tidno;
+
+ /* Init per tid rx state */
+ for (tidno = 0, rxtid = &an->an_aggr.rx.tid[tidno];
+ tidno < WME_NUM_TID;
+ tidno++, rxtid++) {
+ rxtid->an = an;
+ rxtid->seq_reset = 1;
+ rxtid->seq_next = 0;
+ rxtid->baw_size = WME_MAX_BA;
+ rxtid->baw_head = rxtid->baw_tail = 0;
+
+ /*
+ * Ensure the buffer pointer is null at this point
+ * (needs to be allocated when addba is received)
+ */
+
+ rxtid->rxbuf = NULL;
+ setup_timer(&rxtid->timer, ath_rx_timer,
+ (unsigned long)rxtid);
+ spin_lock_init(&rxtid->tidlock);
+
+ /* ADDBA state */
+ rxtid->addba_exchangecomplete = 0;
+ }
+ }
+}
+
+void ath_rx_node_cleanup(struct ath_softc *sc, struct ath_node *an)
+{
+ if (sc->sc_rxaggr) {
+ struct ath_arx_tid *rxtid;
+ int tidno, i;
+
+ /* Init per tid rx state */
+ for (tidno = 0, rxtid = &an->an_aggr.rx.tid[tidno];
+ tidno < WME_NUM_TID;
+ tidno++, rxtid++) {
+
+ if (!rxtid->addba_exchangecomplete)
+ continue;
+
+ /* must cancel timer first */
+ del_timer_sync(&rxtid->timer);
+
+ /* drop any pending sub-frames */
+ ath_rx_flush_tid(sc, rxtid, 1);
+
+ for (i = 0; i < ATH_TID_MAX_BUFS; i++)
+ ASSERT(rxtid->rxbuf[i].rx_wbuf == NULL);
+
+ rxtid->addba_exchangecomplete = 0;
+ }
+ }
+
+}
+
+/* Cleanup per-node receive state */
+
+void ath_rx_node_free(struct ath_softc *sc, struct ath_node *an)
+{
+ ath_rx_node_cleanup(sc, an);
+}
+
+dma_addr_t ath_skb_map_single(struct ath_softc *sc,
+ struct sk_buff *skb,
+ int direction,
+ dma_addr_t *pa)
+{
+ /*
+ * NB: do NOT use skb->len, which is 0 on initialization.
+ * Use skb's entire data area instead.
+ */
+ *pa = pci_map_single(sc->pdev, skb->data,
+ skb_end_pointer(skb) - skb->head, direction);
+ return *pa;
+}
+
+void ath_skb_unmap_single(struct ath_softc *sc,
+ struct sk_buff *skb,
+ int direction,
+ dma_addr_t *pa)
+{
+ /* Unmap skb's entire data area */
+ pci_unmap_single(sc->pdev, *pa,
+ skb_end_pointer(skb) - skb->head, direction);
+}
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef REG_H
+#define REG_H
+
+#define AR_CR 0x0008
+#define AR_CR_RXE 0x00000004
+#define AR_CR_RXD 0x00000020
+#define AR_CR_SWI 0x00000040
+
+#define AR_RXDP 0x000C
+
+#define AR_CFG 0x0014
+#define AR_CFG_SWTD 0x00000001
+#define AR_CFG_SWTB 0x00000002
+#define AR_CFG_SWRD 0x00000004
+#define AR_CFG_SWRB 0x00000008
+#define AR_CFG_SWRG 0x00000010
+#define AR_CFG_AP_ADHOC_INDICATION 0x00000020
+#define AR_CFG_PHOK 0x00000100
+#define AR_CFG_CLK_GATE_DIS 0x00000400
+#define AR_CFG_EEBS 0x00000200
+#define AR_CFG_PCI_MASTER_REQ_Q_THRESH 0x00060000
+#define AR_CFG_PCI_MASTER_REQ_Q_THRESH_S 17
+
+#define AR_MIRT 0x0020
+#define AR_MIRT_VAL 0x0000ffff
+#define AR_MIRT_VAL_S 16
+
+#define AR_IER 0x0024
+#define AR_IER_ENABLE 0x00000001
+#define AR_IER_DISABLE 0x00000000
+
+#define AR_TIMT 0x0028
+#define AR_TIMT_LAST 0x0000ffff
+#define AR_TIMT_LAST_S 0
+#define AR_TIMT_FIRST 0xffff0000
+#define AR_TIMT_FIRST_S 16
+
+#define AR_RIMT 0x002C
+#define AR_RIMT_LAST 0x0000ffff
+#define AR_RIMT_LAST_S 0
+#define AR_RIMT_FIRST 0xffff0000
+#define AR_RIMT_FIRST_S 16
+
+#define AR_DMASIZE_4B 0x00000000
+#define AR_DMASIZE_8B 0x00000001
+#define AR_DMASIZE_16B 0x00000002
+#define AR_DMASIZE_32B 0x00000003
+#define AR_DMASIZE_64B 0x00000004
+#define AR_DMASIZE_128B 0x00000005
+#define AR_DMASIZE_256B 0x00000006
+#define AR_DMASIZE_512B 0x00000007
+
+#define AR_TXCFG 0x0030
+#define AR_TXCFG_DMASZ_MASK 0x00000003
+#define AR_TXCFG_DMASZ_4B 0
+#define AR_TXCFG_DMASZ_8B 1
+#define AR_TXCFG_DMASZ_16B 2
+#define AR_TXCFG_DMASZ_32B 3
+#define AR_TXCFG_DMASZ_64B 4
+#define AR_TXCFG_DMASZ_128B 5
+#define AR_TXCFG_DMASZ_256B 6
+#define AR_TXCFG_DMASZ_512B 7
+#define AR_FTRIG 0x000003F0
+#define AR_FTRIG_S 4
+#define AR_FTRIG_IMMED 0x00000000
+#define AR_FTRIG_64B 0x00000010
+#define AR_FTRIG_128B 0x00000020
+#define AR_FTRIG_192B 0x00000030
+#define AR_FTRIG_256B 0x00000040
+#define AR_FTRIG_512B 0x00000080
+#define AR_TXCFG_ADHOC_BEACON_ATIM_TX_POLICY 0x00000800
+
+#define AR_RXCFG 0x0034
+#define AR_RXCFG_CHIRP 0x00000008
+#define AR_RXCFG_ZLFDMA 0x00000010
+#define AR_RXCFG_DMASZ_MASK 0x00000007
+#define AR_RXCFG_DMASZ_4B 0
+#define AR_RXCFG_DMASZ_8B 1
+#define AR_RXCFG_DMASZ_16B 2
+#define AR_RXCFG_DMASZ_32B 3
+#define AR_RXCFG_DMASZ_64B 4
+#define AR_RXCFG_DMASZ_128B 5
+#define AR_RXCFG_DMASZ_256B 6
+#define AR_RXCFG_DMASZ_512B 7
+
+#define AR_MIBC 0x0040
+#define AR_MIBC_COW 0x00000001
+#define AR_MIBC_FMC 0x00000002
+#define AR_MIBC_CMC 0x00000004
+#define AR_MIBC_MCS 0x00000008
+
+#define AR_TOPS 0x0044
+#define AR_TOPS_MASK 0x0000FFFF
+
+#define AR_RXNPTO 0x0048
+#define AR_RXNPTO_MASK 0x000003FF
+
+#define AR_TXNPTO 0x004C
+#define AR_TXNPTO_MASK 0x000003FF
+#define AR_TXNPTO_QCU_MASK 0x000FFC00
+
+#define AR_RPGTO 0x0050
+#define AR_RPGTO_MASK 0x000003FF
+
+#define AR_RPCNT 0x0054
+#define AR_RPCNT_MASK 0x0000001F
+
+#define AR_MACMISC 0x0058
+#define AR_MACMISC_PCI_EXT_FORCE 0x00000010
+#define AR_MACMISC_DMA_OBS 0x000001E0
+#define AR_MACMISC_DMA_OBS_S 5
+#define AR_MACMISC_DMA_OBS_LINE_0 0
+#define AR_MACMISC_DMA_OBS_LINE_1 1
+#define AR_MACMISC_DMA_OBS_LINE_2 2
+#define AR_MACMISC_DMA_OBS_LINE_3 3
+#define AR_MACMISC_DMA_OBS_LINE_4 4
+#define AR_MACMISC_DMA_OBS_LINE_5 5
+#define AR_MACMISC_DMA_OBS_LINE_6 6
+#define AR_MACMISC_DMA_OBS_LINE_7 7
+#define AR_MACMISC_DMA_OBS_LINE_8 8
+#define AR_MACMISC_MISC_OBS 0x00000E00
+#define AR_MACMISC_MISC_OBS_S 9
+#define AR_MACMISC_MISC_OBS_BUS_LSB 0x00007000
+#define AR_MACMISC_MISC_OBS_BUS_LSB_S 12
+#define AR_MACMISC_MISC_OBS_BUS_MSB 0x00038000
+#define AR_MACMISC_MISC_OBS_BUS_MSB_S 15
+#define AR_MACMISC_MISC_OBS_BUS_1 1
+
+#define AR_GTXTO 0x0064
+#define AR_GTXTO_TIMEOUT_COUNTER 0x0000FFFF
+#define AR_GTXTO_TIMEOUT_LIMIT 0xFFFF0000
+#define AR_GTXTO_TIMEOUT_LIMIT_S 16
+
+#define AR_GTTM 0x0068
+#define AR_GTTM_USEC 0x00000001
+#define AR_GTTM_IGNORE_IDLE 0x00000002
+#define AR_GTTM_RESET_IDLE 0x00000004
+#define AR_GTTM_CST_USEC 0x00000008
+
+#define AR_CST 0x006C
+#define AR_CST_TIMEOUT_COUNTER 0x0000FFFF
+#define AR_CST_TIMEOUT_LIMIT 0xFFFF0000
+#define AR_CST_TIMEOUT_LIMIT_S 16
+
+#define AR_SREV_VERSION_9100 0x014
+
+#define AR_SREV_5416_V20_OR_LATER(_ah) \
+ (AR_SREV_9100((_ah)) || AR_SREV_5416_20_OR_LATER(_ah))
+#define AR_SREV_5416_V22_OR_LATER(_ah) \
+ (AR_SREV_9100((_ah)) || AR_SREV_5416_22_OR_LATER(_ah))
+
+#define AR_ISR 0x0080
+#define AR_ISR_RXOK 0x00000001
+#define AR_ISR_RXDESC 0x00000002
+#define AR_ISR_RXERR 0x00000004
+#define AR_ISR_RXNOPKT 0x00000008
+#define AR_ISR_RXEOL 0x00000010
+#define AR_ISR_RXORN 0x00000020
+#define AR_ISR_TXOK 0x00000040
+#define AR_ISR_TXDESC 0x00000080
+#define AR_ISR_TXERR 0x00000100
+#define AR_ISR_TXNOPKT 0x00000200
+#define AR_ISR_TXEOL 0x00000400
+#define AR_ISR_TXURN 0x00000800
+#define AR_ISR_MIB 0x00001000
+#define AR_ISR_SWI 0x00002000
+#define AR_ISR_RXPHY 0x00004000
+#define AR_ISR_RXKCM 0x00008000
+#define AR_ISR_SWBA 0x00010000
+#define AR_ISR_BRSSI 0x00020000
+#define AR_ISR_BMISS 0x00040000
+#define AR_ISR_BNR 0x00100000
+#define AR_ISR_RXCHIRP 0x00200000
+#define AR_ISR_BCNMISC 0x00800000
+#define AR_ISR_TIM 0x00800000
+#define AR_ISR_QCBROVF 0x02000000
+#define AR_ISR_QCBRURN 0x04000000
+#define AR_ISR_QTRIG 0x08000000
+#define AR_ISR_GENTMR 0x10000000
+
+#define AR_ISR_TXMINTR 0x00080000
+#define AR_ISR_RXMINTR 0x01000000
+#define AR_ISR_TXINTM 0x40000000
+#define AR_ISR_RXINTM 0x80000000
+
+#define AR_ISR_S0 0x0084
+#define AR_ISR_S0_QCU_TXOK 0x000003FF
+#define AR_ISR_S0_QCU_TXOK_S 0
+#define AR_ISR_S0_QCU_TXDESC 0x03FF0000
+#define AR_ISR_S0_QCU_TXDESC_S 16
+
+#define AR_ISR_S1 0x0088
+#define AR_ISR_S1_QCU_TXERR 0x000003FF
+#define AR_ISR_S1_QCU_TXERR_S 0
+#define AR_ISR_S1_QCU_TXEOL 0x03FF0000
+#define AR_ISR_S1_QCU_TXEOL_S 16
+
+#define AR_ISR_S2 0x008c
+#define AR_ISR_S2_QCU_TXURN 0x000003FF
+#define AR_ISR_S2_CST 0x00400000
+#define AR_ISR_S2_GTT 0x00800000
+#define AR_ISR_S2_TIM 0x01000000
+#define AR_ISR_S2_CABEND 0x02000000
+#define AR_ISR_S2_DTIMSYNC 0x04000000
+#define AR_ISR_S2_BCNTO 0x08000000
+#define AR_ISR_S2_CABTO 0x10000000
+#define AR_ISR_S2_DTIM 0x20000000
+#define AR_ISR_S2_TSFOOR 0x40000000
+#define AR_ISR_S2_TBTT_TIME 0x80000000
+
+#define AR_ISR_S3 0x0090
+#define AR_ISR_S3_QCU_QCBROVF 0x000003FF
+#define AR_ISR_S3_QCU_QCBRURN 0x03FF0000
+
+#define AR_ISR_S4 0x0094
+#define AR_ISR_S4_QCU_QTRIG 0x000003FF
+#define AR_ISR_S4_RESV0 0xFFFFFC00
+
+#define AR_ISR_S5 0x0098
+#define AR_ISR_S5_TIMER_TRIG 0x000000FF
+#define AR_ISR_S5_TIMER_THRESH 0x0007FE00
+#define AR_ISR_S5_TIM_TIMER 0x00000010
+#define AR_ISR_S5_DTIM_TIMER 0x00000020
+#define AR_ISR_S5_S 0x00d8
+#define AR_IMR_S5 0x00b8
+#define AR_IMR_S5_TIM_TIMER 0x00000010
+#define AR_IMR_S5_DTIM_TIMER 0x00000020
+
+
+#define AR_IMR 0x00a0
+#define AR_IMR_RXOK 0x00000001
+#define AR_IMR_RXDESC 0x00000002
+#define AR_IMR_RXERR 0x00000004
+#define AR_IMR_RXNOPKT 0x00000008
+#define AR_IMR_RXEOL 0x00000010
+#define AR_IMR_RXORN 0x00000020
+#define AR_IMR_TXOK 0x00000040
+#define AR_IMR_TXDESC 0x00000080
+#define AR_IMR_TXERR 0x00000100
+#define AR_IMR_TXNOPKT 0x00000200
+#define AR_IMR_TXEOL 0x00000400
+#define AR_IMR_TXURN 0x00000800
+#define AR_IMR_MIB 0x00001000
+#define AR_IMR_SWI 0x00002000
+#define AR_IMR_RXPHY 0x00004000
+#define AR_IMR_RXKCM 0x00008000
+#define AR_IMR_SWBA 0x00010000
+#define AR_IMR_BRSSI 0x00020000
+#define AR_IMR_BMISS 0x00040000
+#define AR_IMR_BNR 0x00100000
+#define AR_IMR_RXCHIRP 0x00200000
+#define AR_IMR_BCNMISC 0x00800000
+#define AR_IMR_TIM 0x00800000
+#define AR_IMR_QCBROVF 0x02000000
+#define AR_IMR_QCBRURN 0x04000000
+#define AR_IMR_QTRIG 0x08000000
+#define AR_IMR_GENTMR 0x10000000
+
+#define AR_IMR_TXMINTR 0x00080000
+#define AR_IMR_RXMINTR 0x01000000
+#define AR_IMR_TXINTM 0x40000000
+#define AR_IMR_RXINTM 0x80000000
+
+#define AR_IMR_S0 0x00a4
+#define AR_IMR_S0_QCU_TXOK 0x000003FF
+#define AR_IMR_S0_QCU_TXOK_S 0
+#define AR_IMR_S0_QCU_TXDESC 0x03FF0000
+#define AR_IMR_S0_QCU_TXDESC_S 16
+
+#define AR_IMR_S1 0x00a8
+#define AR_IMR_S1_QCU_TXERR 0x000003FF
+#define AR_IMR_S1_QCU_TXERR_S 0
+#define AR_IMR_S1_QCU_TXEOL 0x03FF0000
+#define AR_IMR_S1_QCU_TXEOL_S 16
+
+#define AR_IMR_S2 0x00ac
+#define AR_IMR_S2_QCU_TXURN 0x000003FF
+#define AR_IMR_S2_QCU_TXURN_S 0
+#define AR_IMR_S2_CST 0x00400000
+#define AR_IMR_S2_GTT 0x00800000
+#define AR_IMR_S2_TIM 0x01000000
+#define AR_IMR_S2_CABEND 0x02000000
+#define AR_IMR_S2_DTIMSYNC 0x04000000
+#define AR_IMR_S2_BCNTO 0x08000000
+#define AR_IMR_S2_CABTO 0x10000000
+#define AR_IMR_S2_DTIM 0x20000000
+#define AR_IMR_S2_TSFOOR 0x40000000
+
+#define AR_IMR_S3 0x00b0
+#define AR_IMR_S3_QCU_QCBROVF 0x000003FF
+#define AR_IMR_S3_QCU_QCBRURN 0x03FF0000
+#define AR_IMR_S3_QCU_QCBRURN_S 16
+
+#define AR_IMR_S4 0x00b4
+#define AR_IMR_S4_QCU_QTRIG 0x000003FF
+#define AR_IMR_S4_RESV0 0xFFFFFC00
+
+#define AR_IMR_S5 0x00b8
+#define AR_IMR_S5_TIMER_TRIG 0x000000FF
+#define AR_IMR_S5_TIMER_THRESH 0x0000FF00
+
+
+#define AR_ISR_RAC 0x00c0
+#define AR_ISR_S0_S 0x00c4
+#define AR_ISR_S0_QCU_TXOK 0x000003FF
+#define AR_ISR_S0_QCU_TXOK_S 0
+#define AR_ISR_S0_QCU_TXDESC 0x03FF0000
+#define AR_ISR_S0_QCU_TXDESC_S 16
+
+#define AR_ISR_S1_S 0x00c8
+#define AR_ISR_S1_QCU_TXERR 0x000003FF
+#define AR_ISR_S1_QCU_TXERR_S 0
+#define AR_ISR_S1_QCU_TXEOL 0x03FF0000
+#define AR_ISR_S1_QCU_TXEOL_S 16
+
+#define AR_ISR_S2_S 0x00cc
+#define AR_ISR_S3_S 0x00d0
+#define AR_ISR_S4_S 0x00d4
+#define AR_ISR_S5_S 0x00d8
+#define AR_DMADBG_0 0x00e0
+#define AR_DMADBG_1 0x00e4
+#define AR_DMADBG_2 0x00e8
+#define AR_DMADBG_3 0x00ec
+#define AR_DMADBG_4 0x00f0
+#define AR_DMADBG_5 0x00f4
+#define AR_DMADBG_6 0x00f8
+#define AR_DMADBG_7 0x00fc
+
+#define AR_NUM_QCU 10
+#define AR_QCU_0 0x0001
+#define AR_QCU_1 0x0002
+#define AR_QCU_2 0x0004
+#define AR_QCU_3 0x0008
+#define AR_QCU_4 0x0010
+#define AR_QCU_5 0x0020
+#define AR_QCU_6 0x0040
+#define AR_QCU_7 0x0080
+#define AR_QCU_8 0x0100
+#define AR_QCU_9 0x0200
+
+#define AR_Q0_TXDP 0x0800
+#define AR_Q1_TXDP 0x0804
+#define AR_Q2_TXDP 0x0808
+#define AR_Q3_TXDP 0x080c
+#define AR_Q4_TXDP 0x0810
+#define AR_Q5_TXDP 0x0814
+#define AR_Q6_TXDP 0x0818
+#define AR_Q7_TXDP 0x081c
+#define AR_Q8_TXDP 0x0820
+#define AR_Q9_TXDP 0x0824
+#define AR_QTXDP(_i) (AR_Q0_TXDP + ((_i)<<2))
+
+#define AR_Q_TXE 0x0840
+#define AR_Q_TXE_M 0x000003FF
+
+#define AR_Q_TXD 0x0880
+#define AR_Q_TXD_M 0x000003FF
+
+#define AR_Q0_CBRCFG 0x08c0
+#define AR_Q1_CBRCFG 0x08c4
+#define AR_Q2_CBRCFG 0x08c8
+#define AR_Q3_CBRCFG 0x08cc
+#define AR_Q4_CBRCFG 0x08d0
+#define AR_Q5_CBRCFG 0x08d4
+#define AR_Q6_CBRCFG 0x08d8
+#define AR_Q7_CBRCFG 0x08dc
+#define AR_Q8_CBRCFG 0x08e0
+#define AR_Q9_CBRCFG 0x08e4
+#define AR_QCBRCFG(_i) (AR_Q0_CBRCFG + ((_i)<<2))
+#define AR_Q_CBRCFG_INTERVAL 0x00FFFFFF
+#define AR_Q_CBRCFG_INTERVAL_S 0
+#define AR_Q_CBRCFG_OVF_THRESH 0xFF000000
+#define AR_Q_CBRCFG_OVF_THRESH_S 24
+
+#define AR_Q0_RDYTIMECFG 0x0900
+#define AR_Q1_RDYTIMECFG 0x0904
+#define AR_Q2_RDYTIMECFG 0x0908
+#define AR_Q3_RDYTIMECFG 0x090c
+#define AR_Q4_RDYTIMECFG 0x0910
+#define AR_Q5_RDYTIMECFG 0x0914
+#define AR_Q6_RDYTIMECFG 0x0918
+#define AR_Q7_RDYTIMECFG 0x091c
+#define AR_Q8_RDYTIMECFG 0x0920
+#define AR_Q9_RDYTIMECFG 0x0924
+#define AR_QRDYTIMECFG(_i) (AR_Q0_RDYTIMECFG + ((_i)<<2))
+#define AR_Q_RDYTIMECFG_DURATION 0x00FFFFFF
+#define AR_Q_RDYTIMECFG_DURATION_S 0
+#define AR_Q_RDYTIMECFG_EN 0x01000000
+
+#define AR_Q_ONESHOTARM_SC 0x0940
+#define AR_Q_ONESHOTARM_SC_M 0x000003FF
+#define AR_Q_ONESHOTARM_SC_RESV0 0xFFFFFC00
+
+#define AR_Q_ONESHOTARM_CC 0x0980
+#define AR_Q_ONESHOTARM_CC_M 0x000003FF
+#define AR_Q_ONESHOTARM_CC_RESV0 0xFFFFFC00
+
+#define AR_Q0_MISC 0x09c0
+#define AR_Q1_MISC 0x09c4
+#define AR_Q2_MISC 0x09c8
+#define AR_Q3_MISC 0x09cc
+#define AR_Q4_MISC 0x09d0
+#define AR_Q5_MISC 0x09d4
+#define AR_Q6_MISC 0x09d8
+#define AR_Q7_MISC 0x09dc
+#define AR_Q8_MISC 0x09e0
+#define AR_Q9_MISC 0x09e4
+#define AR_QMISC(_i) (AR_Q0_MISC + ((_i)<<2))
+#define AR_Q_MISC_FSP 0x0000000F
+#define AR_Q_MISC_FSP_ASAP 0
+#define AR_Q_MISC_FSP_CBR 1
+#define AR_Q_MISC_FSP_DBA_GATED 2
+#define AR_Q_MISC_FSP_TIM_GATED 3
+#define AR_Q_MISC_FSP_BEACON_SENT_GATED 4
+#define AR_Q_MISC_FSP_BEACON_RCVD_GATED 5
+#define AR_Q_MISC_ONE_SHOT_EN 0x00000010
+#define AR_Q_MISC_CBR_INCR_DIS1 0x00000020
+#define AR_Q_MISC_CBR_INCR_DIS0 0x00000040
+#define AR_Q_MISC_BEACON_USE 0x00000080
+#define AR_Q_MISC_CBR_EXP_CNTR_LIMIT_EN 0x00000100
+#define AR_Q_MISC_RDYTIME_EXP_POLICY 0x00000200
+#define AR_Q_MISC_RESET_CBR_EXP_CTR 0x00000400
+#define AR_Q_MISC_DCU_EARLY_TERM_REQ 0x00000800
+#define AR_Q_MISC_RESV0 0xFFFFF000
+
+#define AR_Q0_STS 0x0a00
+#define AR_Q1_STS 0x0a04
+#define AR_Q2_STS 0x0a08
+#define AR_Q3_STS 0x0a0c
+#define AR_Q4_STS 0x0a10
+#define AR_Q5_STS 0x0a14
+#define AR_Q6_STS 0x0a18
+#define AR_Q7_STS 0x0a1c
+#define AR_Q8_STS 0x0a20
+#define AR_Q9_STS 0x0a24
+#define AR_QSTS(_i) (AR_Q0_STS + ((_i)<<2))
+#define AR_Q_STS_PEND_FR_CNT 0x00000003
+#define AR_Q_STS_RESV0 0x000000FC
+#define AR_Q_STS_CBR_EXP_CNT 0x0000FF00
+#define AR_Q_STS_RESV1 0xFFFF0000
+
+#define AR_Q_RDYTIMESHDN 0x0a40
+#define AR_Q_RDYTIMESHDN_M 0x000003FF
+
+
+#define AR_NUM_DCU 10
+#define AR_DCU_0 0x0001
+#define AR_DCU_1 0x0002
+#define AR_DCU_2 0x0004
+#define AR_DCU_3 0x0008
+#define AR_DCU_4 0x0010
+#define AR_DCU_5 0x0020
+#define AR_DCU_6 0x0040
+#define AR_DCU_7 0x0080
+#define AR_DCU_8 0x0100
+#define AR_DCU_9 0x0200
+
+#define AR_D0_QCUMASK 0x1000
+#define AR_D1_QCUMASK 0x1004
+#define AR_D2_QCUMASK 0x1008
+#define AR_D3_QCUMASK 0x100c
+#define AR_D4_QCUMASK 0x1010
+#define AR_D5_QCUMASK 0x1014
+#define AR_D6_QCUMASK 0x1018
+#define AR_D7_QCUMASK 0x101c
+#define AR_D8_QCUMASK 0x1020
+#define AR_D9_QCUMASK 0x1024
+#define AR_DQCUMASK(_i) (AR_D0_QCUMASK + ((_i)<<2))
+#define AR_D_QCUMASK 0x000003FF
+#define AR_D_QCUMASK_RESV0 0xFFFFFC00
+
+#define AR_D_TXBLK_CMD 0x1038
+#define AR_D_TXBLK_DATA(i) (AR_D_TXBLK_CMD+(i))
+
+#define AR_D0_LCL_IFS 0x1040
+#define AR_D1_LCL_IFS 0x1044
+#define AR_D2_LCL_IFS 0x1048
+#define AR_D3_LCL_IFS 0x104c
+#define AR_D4_LCL_IFS 0x1050
+#define AR_D5_LCL_IFS 0x1054
+#define AR_D6_LCL_IFS 0x1058
+#define AR_D7_LCL_IFS 0x105c
+#define AR_D8_LCL_IFS 0x1060
+#define AR_D9_LCL_IFS 0x1064
+#define AR_DLCL_IFS(_i) (AR_D0_LCL_IFS + ((_i)<<2))
+#define AR_D_LCL_IFS_CWMIN 0x000003FF
+#define AR_D_LCL_IFS_CWMIN_S 0
+#define AR_D_LCL_IFS_CWMAX 0x000FFC00
+#define AR_D_LCL_IFS_CWMAX_S 10
+#define AR_D_LCL_IFS_AIFS 0x0FF00000
+#define AR_D_LCL_IFS_AIFS_S 20
+
+#define AR_D_LCL_IFS_RESV0 0xF0000000
+
+#define AR_D0_RETRY_LIMIT 0x1080
+#define AR_D1_RETRY_LIMIT 0x1084
+#define AR_D2_RETRY_LIMIT 0x1088
+#define AR_D3_RETRY_LIMIT 0x108c
+#define AR_D4_RETRY_LIMIT 0x1090
+#define AR_D5_RETRY_LIMIT 0x1094
+#define AR_D6_RETRY_LIMIT 0x1098
+#define AR_D7_RETRY_LIMIT 0x109c
+#define AR_D8_RETRY_LIMIT 0x10a0
+#define AR_D9_RETRY_LIMIT 0x10a4
+#define AR_DRETRY_LIMIT(_i) (AR_D0_RETRY_LIMIT + ((_i)<<2))
+#define AR_D_RETRY_LIMIT_FR_SH 0x0000000F
+#define AR_D_RETRY_LIMIT_FR_SH_S 0
+#define AR_D_RETRY_LIMIT_STA_SH 0x00003F00
+#define AR_D_RETRY_LIMIT_STA_SH_S 8
+#define AR_D_RETRY_LIMIT_STA_LG 0x000FC000
+#define AR_D_RETRY_LIMIT_STA_LG_S 14
+#define AR_D_RETRY_LIMIT_RESV0 0xFFF00000
+
+#define AR_D0_CHNTIME 0x10c0
+#define AR_D1_CHNTIME 0x10c4
+#define AR_D2_CHNTIME 0x10c8
+#define AR_D3_CHNTIME 0x10cc
+#define AR_D4_CHNTIME 0x10d0
+#define AR_D5_CHNTIME 0x10d4
+#define AR_D6_CHNTIME 0x10d8
+#define AR_D7_CHNTIME 0x10dc
+#define AR_D8_CHNTIME 0x10e0
+#define AR_D9_CHNTIME 0x10e4
+#define AR_DCHNTIME(_i) (AR_D0_CHNTIME + ((_i)<<2))
+#define AR_D_CHNTIME_DUR 0x000FFFFF
+#define AR_D_CHNTIME_DUR_S 0
+#define AR_D_CHNTIME_EN 0x00100000
+#define AR_D_CHNTIME_RESV0 0xFFE00000
+
+#define AR_D0_MISC 0x1100
+#define AR_D1_MISC 0x1104
+#define AR_D2_MISC 0x1108
+#define AR_D3_MISC 0x110c
+#define AR_D4_MISC 0x1110
+#define AR_D5_MISC 0x1114
+#define AR_D6_MISC 0x1118
+#define AR_D7_MISC 0x111c
+#define AR_D8_MISC 0x1120
+#define AR_D9_MISC 0x1124
+#define AR_DMISC(_i) (AR_D0_MISC + ((_i)<<2))
+#define AR_D_MISC_BKOFF_THRESH 0x0000003F
+#define AR_D_MISC_RETRY_CNT_RESET_EN 0x00000040
+#define AR_D_MISC_CW_RESET_EN 0x00000080
+#define AR_D_MISC_FRAG_WAIT_EN 0x00000100
+#define AR_D_MISC_FRAG_BKOFF_EN 0x00000200
+#define AR_D_MISC_CW_BKOFF_EN 0x00001000
+#define AR_D_MISC_VIR_COL_HANDLING 0x0000C000
+#define AR_D_MISC_VIR_COL_HANDLING_S 14
+#define AR_D_MISC_VIR_COL_HANDLING_DEFAULT 0
+#define AR_D_MISC_VIR_COL_HANDLING_IGNORE 1
+#define AR_D_MISC_BEACON_USE 0x00010000
+#define AR_D_MISC_ARB_LOCKOUT_CNTRL 0x00060000
+#define AR_D_MISC_ARB_LOCKOUT_CNTRL_S 17
+#define AR_D_MISC_ARB_LOCKOUT_CNTRL_NONE 0
+#define AR_D_MISC_ARB_LOCKOUT_CNTRL_INTRA_FR 1
+#define AR_D_MISC_ARB_LOCKOUT_CNTRL_GLOBAL 2
+#define AR_D_MISC_ARB_LOCKOUT_IGNORE 0x00080000
+#define AR_D_MISC_SEQ_NUM_INCR_DIS 0x00100000
+#define AR_D_MISC_POST_FR_BKOFF_DIS 0x00200000
+#define AR_D_MISC_VIT_COL_CW_BKOFF_EN 0x00400000
+#define AR_D_MISC_BLOWN_IFS_RETRY_EN 0x00800000
+#define AR_D_MISC_RESV0 0xFF000000
+
+#define AR_D_SEQNUM 0x1140
+
+#define AR_D_GBL_IFS_SIFS 0x1030
+#define AR_D_GBL_IFS_SIFS_M 0x0000FFFF
+#define AR_D_GBL_IFS_SIFS_RESV0 0xFFFFFFFF
+
+#define AR_D_TXBLK_BASE 0x1038
+#define AR_D_TXBLK_WRITE_BITMASK 0x0000FFFF
+#define AR_D_TXBLK_WRITE_BITMASK_S 0
+#define AR_D_TXBLK_WRITE_SLICE 0x000F0000
+#define AR_D_TXBLK_WRITE_SLICE_S 16
+#define AR_D_TXBLK_WRITE_DCU 0x00F00000
+#define AR_D_TXBLK_WRITE_DCU_S 20
+#define AR_D_TXBLK_WRITE_COMMAND 0x0F000000
+#define AR_D_TXBLK_WRITE_COMMAND_S 24
+
+#define AR_D_GBL_IFS_SLOT 0x1070
+#define AR_D_GBL_IFS_SLOT_M 0x0000FFFF
+#define AR_D_GBL_IFS_SLOT_RESV0 0xFFFF0000
+
+#define AR_D_GBL_IFS_EIFS 0x10b0
+#define AR_D_GBL_IFS_EIFS_M 0x0000FFFF
+#define AR_D_GBL_IFS_EIFS_RESV0 0xFFFF0000
+
+#define AR_D_GBL_IFS_MISC 0x10f0
+#define AR_D_GBL_IFS_MISC_LFSR_SLICE_SEL 0x00000007
+#define AR_D_GBL_IFS_MISC_TURBO_MODE 0x00000008
+#define AR_D_GBL_IFS_MISC_USEC_DURATION 0x000FFC00
+#define AR_D_GBL_IFS_MISC_DCU_ARBITER_DLY 0x00300000
+#define AR_D_GBL_IFS_MISC_RANDOM_LFSR_SLICE_DIS 0x01000000
+#define AR_D_GBL_IFS_MISC_SLOT_XMIT_WIND_LEN 0x06000000
+#define AR_D_GBL_IFS_MISC_FORCE_XMIT_SLOT_BOUND 0x08000000
+#define AR_D_GBL_IFS_MISC_IGNORE_BACKOFF 0x10000000
+
+#define AR_D_FPCTL 0x1230
+#define AR_D_FPCTL_DCU 0x0000000F
+#define AR_D_FPCTL_DCU_S 0
+#define AR_D_FPCTL_PREFETCH_EN 0x00000010
+#define AR_D_FPCTL_BURST_PREFETCH 0x00007FE0
+#define AR_D_FPCTL_BURST_PREFETCH_S 5
+
+#define AR_D_TXPSE 0x1270
+#define AR_D_TXPSE_CTRL 0x000003FF
+#define AR_D_TXPSE_RESV0 0x0000FC00
+#define AR_D_TXPSE_STATUS 0x00010000
+#define AR_D_TXPSE_RESV1 0xFFFE0000
+
+#define AR_D_TXSLOTMASK 0x12f0
+#define AR_D_TXSLOTMASK_NUM 0x0000000F
+
+#define AR_CFG_LED 0x1f04
+#define AR_CFG_SCLK_RATE_IND 0x00000003
+#define AR_CFG_SCLK_RATE_IND_S 0
+#define AR_CFG_SCLK_32MHZ 0x00000000
+#define AR_CFG_SCLK_4MHZ 0x00000001
+#define AR_CFG_SCLK_1MHZ 0x00000002
+#define AR_CFG_SCLK_32KHZ 0x00000003
+#define AR_CFG_LED_BLINK_SLOW 0x00000008
+#define AR_CFG_LED_BLINK_THRESH_SEL 0x00000070
+#define AR_CFG_LED_MODE_SEL 0x00000380
+#define AR_CFG_LED_MODE_SEL_S 7
+#define AR_CFG_LED_POWER 0x00000280
+#define AR_CFG_LED_POWER_S 7
+#define AR_CFG_LED_NETWORK 0x00000300
+#define AR_CFG_LED_NETWORK_S 7
+#define AR_CFG_LED_MODE_PROP 0x0
+#define AR_CFG_LED_MODE_RPROP 0x1
+#define AR_CFG_LED_MODE_SPLIT 0x2
+#define AR_CFG_LED_MODE_RAND 0x3
+#define AR_CFG_LED_MODE_POWER_OFF 0x4
+#define AR_CFG_LED_MODE_POWER_ON 0x5
+#define AR_CFG_LED_MODE_NETWORK_OFF 0x4
+#define AR_CFG_LED_MODE_NETWORK_ON 0x6
+#define AR_CFG_LED_ASSOC_CTL 0x00000c00
+#define AR_CFG_LED_ASSOC_CTL_S 10
+#define AR_CFG_LED_ASSOC_NONE 0x0
+#define AR_CFG_LED_ASSOC_ACTIVE 0x1
+#define AR_CFG_LED_ASSOC_PENDING 0x2
+
+#define AR_CFG_LED_BLINK_SLOW 0x00000008
+#define AR_CFG_LED_BLINK_SLOW_S 3
+
+#define AR_CFG_LED_BLINK_THRESH_SEL 0x00000070
+#define AR_CFG_LED_BLINK_THRESH_SEL_S 4
+
+#define AR_MAC_SLEEP 0x1f00
+#define AR_MAC_SLEEP_MAC_AWAKE 0x00000000
+#define AR_MAC_SLEEP_MAC_ASLEEP 0x00000001
+
+#define AR_RC 0x4000
+#define AR_RC_AHB 0x00000001
+#define AR_RC_APB 0x00000002
+#define AR_RC_HOSTIF 0x00000100
+
+#define AR_WA 0x4004
+
+#define AR_PM_STATE 0x4008
+#define AR_PM_STATE_PME_D3COLD_VAUX 0x00100000
+
+#define AR_HOST_TIMEOUT 0x4018
+#define AR_HOST_TIMEOUT_APB_CNTR 0x0000FFFF
+#define AR_HOST_TIMEOUT_APB_CNTR_S 0
+#define AR_HOST_TIMEOUT_LCL_CNTR 0xFFFF0000
+#define AR_HOST_TIMEOUT_LCL_CNTR_S 16
+
+#define AR_EEPROM 0x401c
+#define AR_EEPROM_ABSENT 0x00000100
+#define AR_EEPROM_CORRUPT 0x00000200
+#define AR_EEPROM_PROT_MASK 0x03FFFC00
+#define AR_EEPROM_PROT_MASK_S 10
+
+#define EEPROM_PROTECT_RP_0_31 0x0001
+#define EEPROM_PROTECT_WP_0_31 0x0002
+#define EEPROM_PROTECT_RP_32_63 0x0004
+#define EEPROM_PROTECT_WP_32_63 0x0008
+#define EEPROM_PROTECT_RP_64_127 0x0010
+#define EEPROM_PROTECT_WP_64_127 0x0020
+#define EEPROM_PROTECT_RP_128_191 0x0040
+#define EEPROM_PROTECT_WP_128_191 0x0080
+#define EEPROM_PROTECT_RP_192_255 0x0100
+#define EEPROM_PROTECT_WP_192_255 0x0200
+#define EEPROM_PROTECT_RP_256_511 0x0400
+#define EEPROM_PROTECT_WP_256_511 0x0800
+#define EEPROM_PROTECT_RP_512_1023 0x1000
+#define EEPROM_PROTECT_WP_512_1023 0x2000
+#define EEPROM_PROTECT_RP_1024_2047 0x4000
+#define EEPROM_PROTECT_WP_1024_2047 0x8000
+
+#define AR_SREV \
+ ((AR_SREV_9100(ah)) ? 0x0600 : 0x4020)
+
+#define AR_SREV_ID \
+ ((AR_SREV_9100(ah)) ? 0x00000FFF : 0x000000FF)
+#define AR_SREV_VERSION 0x000000F0
+#define AR_SREV_VERSION_S 4
+#define AR_SREV_REVISION 0x00000007
+
+#define AR_SREV_ID2 0xFFFFFFFF
+#define AR_SREV_VERSION2 0xFFFC0000
+#define AR_SREV_VERSION2_S 18
+#define AR_SREV_TYPE2 0x0003F000
+#define AR_SREV_TYPE2_S 12
+#define AR_SREV_TYPE2_CHAIN 0x00001000
+#define AR_SREV_TYPE2_HOST_MODE 0x00002000
+#define AR_SREV_REVISION2 0x00000F00
+#define AR_SREV_REVISION2_S 8
+
+#define AR_SREV_VERSION_5416_PCI 0xD
+#define AR_SREV_VERSION_5416_PCIE 0xC
+#define AR_SREV_REVISION_5416_10 0
+#define AR_SREV_REVISION_5416_20 1
+#define AR_SREV_REVISION_5416_22 2
+#define AR_SREV_VERSION_9160 0x40
+#define AR_SREV_REVISION_9160_10 0
+#define AR_SREV_REVISION_9160_11 1
+#define AR_SREV_VERSION_9280 0x80
+#define AR_SREV_REVISION_9280_10 0
+#define AR_SREV_REVISION_9280_20 1
+#define AR_SREV_REVISION_9280_21 2
+#define AR_SREV_VERSION_9285 0xC0
+#define AR_SREV_REVISION_9285_10 0
+
+#define AR_SREV_9100_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_5416_PCIE))
+#define AR_SREV_5416_20_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_9160) || \
+ ((_ah)->ah_macRev >= AR_SREV_REVISION_5416_20))
+#define AR_SREV_5416_22_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_9160) || \
+ ((_ah)->ah_macRev >= AR_SREV_REVISION_5416_22))
+#define AR_SREV_9160(_ah) \
+ (((_ah)->ah_macVersion == AR_SREV_VERSION_9160))
+#define AR_SREV_9160_10_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_9160))
+#define AR_SREV_9160_11(_ah) \
+ (AR_SREV_9160(_ah) && ((_ah)->ah_macRev == AR_SREV_REVISION_9160_11))
+#define AR_SREV_9280(_ah) \
+ (((_ah)->ah_macVersion == AR_SREV_VERSION_9280))
+#define AR_SREV_9280_10_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_9280))
+#define AR_SREV_9280_20(_ah) \
+ (((_ah)->ah_macVersion == AR_SREV_VERSION_9280) && \
+ ((_ah)->ah_macRev >= AR_SREV_REVISION_9280_20))
+#define AR_SREV_9280_20_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion > AR_SREV_VERSION_9280) || \
+ (((_ah)->ah_macVersion == AR_SREV_VERSION_9280) && \
+ ((_ah)->ah_macRev >= AR_SREV_REVISION_9280_20)))
+
+#define AR_SREV_9285(_ah) (((_ah)->ah_macVersion == AR_SREV_VERSION_9285))
+#define AR_SREV_9285_10_OR_LATER(_ah) \
+ (((_ah)->ah_macVersion >= AR_SREV_VERSION_9285))
+
+#define AR_RADIO_SREV_MAJOR 0xf0
+#define AR_RAD5133_SREV_MAJOR 0xc0
+#define AR_RAD2133_SREV_MAJOR 0xd0
+#define AR_RAD5122_SREV_MAJOR 0xe0
+#define AR_RAD2122_SREV_MAJOR 0xf0
+
+#define AR_AHB_MODE 0x4024
+#define AR_AHB_EXACT_WR_EN 0x00000000
+#define AR_AHB_BUF_WR_EN 0x00000001
+#define AR_AHB_EXACT_RD_EN 0x00000000
+#define AR_AHB_CACHELINE_RD_EN 0x00000002
+#define AR_AHB_PREFETCH_RD_EN 0x00000004
+#define AR_AHB_PAGE_SIZE_1K 0x00000000
+#define AR_AHB_PAGE_SIZE_2K 0x00000008
+#define AR_AHB_PAGE_SIZE_4K 0x00000010
+
+#define AR_INTR_RTC_IRQ 0x00000001
+#define AR_INTR_MAC_IRQ 0x00000002
+#define AR_INTR_EEP_PROT_ACCESS 0x00000004
+#define AR_INTR_MAC_AWAKE 0x00020000
+#define AR_INTR_MAC_ASLEEP 0x00040000
+#define AR_INTR_SPURIOUS 0xFFFFFFFF
+
+
+#define AR_INTR_SYNC_CAUSE_CLR 0x4028
+
+#define AR_INTR_SYNC_CAUSE 0x4028
+
+#define AR_INTR_SYNC_ENABLE 0x402c
+#define AR_INTR_SYNC_ENABLE_GPIO 0xFFFC0000
+#define AR_INTR_SYNC_ENABLE_GPIO_S 18
+
+enum {
+ AR_INTR_SYNC_RTC_IRQ = 0x00000001,
+ AR_INTR_SYNC_MAC_IRQ = 0x00000002,
+ AR_INTR_SYNC_EEPROM_ILLEGAL_ACCESS = 0x00000004,
+ AR_INTR_SYNC_APB_TIMEOUT = 0x00000008,
+ AR_INTR_SYNC_PCI_MODE_CONFLICT = 0x00000010,
+ AR_INTR_SYNC_HOST1_FATAL = 0x00000020,
+ AR_INTR_SYNC_HOST1_PERR = 0x00000040,
+ AR_INTR_SYNC_TRCV_FIFO_PERR = 0x00000080,
+ AR_INTR_SYNC_RADM_CPL_EP = 0x00000100,
+ AR_INTR_SYNC_RADM_CPL_DLLP_ABORT = 0x00000200,
+ AR_INTR_SYNC_RADM_CPL_TLP_ABORT = 0x00000400,
+ AR_INTR_SYNC_RADM_CPL_ECRC_ERR = 0x00000800,
+ AR_INTR_SYNC_RADM_CPL_TIMEOUT = 0x00001000,
+ AR_INTR_SYNC_LOCAL_TIMEOUT = 0x00002000,
+ AR_INTR_SYNC_PM_ACCESS = 0x00004000,
+ AR_INTR_SYNC_MAC_AWAKE = 0x00008000,
+ AR_INTR_SYNC_MAC_ASLEEP = 0x00010000,
+ AR_INTR_SYNC_MAC_SLEEP_ACCESS = 0x00020000,
+ AR_INTR_SYNC_ALL = 0x0003FFFF,
+
+
+ AR_INTR_SYNC_DEFAULT = (AR_INTR_SYNC_HOST1_FATAL |
+ AR_INTR_SYNC_HOST1_PERR |
+ AR_INTR_SYNC_RADM_CPL_EP |
+ AR_INTR_SYNC_RADM_CPL_DLLP_ABORT |
+ AR_INTR_SYNC_RADM_CPL_TLP_ABORT |
+ AR_INTR_SYNC_RADM_CPL_ECRC_ERR |
+ AR_INTR_SYNC_RADM_CPL_TIMEOUT |
+ AR_INTR_SYNC_LOCAL_TIMEOUT |
+ AR_INTR_SYNC_MAC_SLEEP_ACCESS),
+
+ AR_INTR_SYNC_SPURIOUS = 0xFFFFFFFF,
+
+};
+
+#define AR_INTR_ASYNC_MASK 0x4030
+#define AR_INTR_ASYNC_MASK_GPIO 0xFFFC0000
+#define AR_INTR_ASYNC_MASK_GPIO_S 18
+
+#define AR_INTR_SYNC_MASK 0x4034
+#define AR_INTR_SYNC_MASK_GPIO 0xFFFC0000
+#define AR_INTR_SYNC_MASK_GPIO_S 18
+
+#define AR_INTR_ASYNC_CAUSE_CLR 0x4038
+#define AR_INTR_ASYNC_CAUSE 0x4038
+
+#define AR_INTR_ASYNC_ENABLE 0x403c
+#define AR_INTR_ASYNC_ENABLE_GPIO 0xFFFC0000
+#define AR_INTR_ASYNC_ENABLE_GPIO_S 18
+
+#define AR_PCIE_SERDES 0x4040
+#define AR_PCIE_SERDES2 0x4044
+#define AR_PCIE_PM_CTRL 0x4014
+#define AR_PCIE_PM_CTRL_ENA 0x00080000
+
+#define AR_NUM_GPIO 14
+#define AR928X_NUM_GPIO 10
+
+#define AR_GPIO_IN_OUT 0x4048
+#define AR_GPIO_IN_VAL 0x0FFFC000
+#define AR_GPIO_IN_VAL_S 14
+#define AR928X_GPIO_IN_VAL 0x000FFC00
+#define AR928X_GPIO_IN_VAL_S 10
+
+#define AR_GPIO_OE_OUT 0x404c
+#define AR_GPIO_OE_OUT_DRV 0x3
+#define AR_GPIO_OE_OUT_DRV_NO 0x0
+#define AR_GPIO_OE_OUT_DRV_LOW 0x1
+#define AR_GPIO_OE_OUT_DRV_HI 0x2
+#define AR_GPIO_OE_OUT_DRV_ALL 0x3
+
+#define AR_GPIO_INTR_POL 0x4050
+#define AR_GPIO_INTR_POL_VAL 0x00001FFF
+#define AR_GPIO_INTR_POL_VAL_S 0
+
+#define AR_GPIO_INPUT_EN_VAL 0x4054
+#define AR_GPIO_INPUT_EN_VAL_RFSILENT_DEF 0x00000080
+#define AR_GPIO_INPUT_EN_VAL_RFSILENT_DEF_S 7
+#define AR_GPIO_INPUT_EN_VAL_RFSILENT_BB 0x00008000
+#define AR_GPIO_INPUT_EN_VAL_RFSILENT_BB_S 15
+#define AR_GPIO_RTC_RESET_OVERRIDE_ENABLE 0x00010000
+#define AR_GPIO_JTAG_DISABLE 0x00020000
+
+#define AR_GPIO_INPUT_MUX1 0x4058
+
+#define AR_GPIO_INPUT_MUX2 0x405c
+#define AR_GPIO_INPUT_MUX2_CLK25 0x0000000f
+#define AR_GPIO_INPUT_MUX2_CLK25_S 0
+#define AR_GPIO_INPUT_MUX2_RFSILENT 0x000000f0
+#define AR_GPIO_INPUT_MUX2_RFSILENT_S 4
+#define AR_GPIO_INPUT_MUX2_RTC_RESET 0x00000f00
+#define AR_GPIO_INPUT_MUX2_RTC_RESET_S 8
+
+#define AR_GPIO_OUTPUT_MUX1 0x4060
+#define AR_GPIO_OUTPUT_MUX2 0x4064
+#define AR_GPIO_OUTPUT_MUX3 0x4068
+
+#define AR_GPIO_OUTPUT_MUX_AS_OUTPUT 0
+#define AR_GPIO_OUTPUT_MUX_AS_PCIE_ATTENTION_LED 1
+#define AR_GPIO_OUTPUT_MUX_AS_PCIE_POWER_LED 2
+#define AR_GPIO_OUTPUT_MUX_AS_MAC_NETWORK_LED 5
+#define AR_GPIO_OUTPUT_MUX_AS_MAC_POWER_LED 6
+
+#define AR_INPUT_STATE 0x406c
+
+#define AR_EEPROM_STATUS_DATA 0x407c
+#define AR_EEPROM_STATUS_DATA_VAL 0x0000ffff
+#define AR_EEPROM_STATUS_DATA_VAL_S 0
+#define AR_EEPROM_STATUS_DATA_BUSY 0x00010000
+#define AR_EEPROM_STATUS_DATA_BUSY_ACCESS 0x00020000
+#define AR_EEPROM_STATUS_DATA_PROT_ACCESS 0x00040000
+#define AR_EEPROM_STATUS_DATA_ABSENT_ACCESS 0x00080000
+
+#define AR_OBS 0x4080
+
+#define AR_PCIE_MSI 0x4094
+#define AR_PCIE_MSI_ENABLE 0x00000001
+
+
+#define AR_RTC_9160_PLL_DIV 0x000003ff
+#define AR_RTC_9160_PLL_DIV_S 0
+#define AR_RTC_9160_PLL_REFDIV 0x00003C00
+#define AR_RTC_9160_PLL_REFDIV_S 10
+#define AR_RTC_9160_PLL_CLKSEL 0x0000C000
+#define AR_RTC_9160_PLL_CLKSEL_S 14
+
+#define AR_RTC_BASE 0x00020000
+#define AR_RTC_RC \
+ (AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0000) : 0x7000
+#define AR_RTC_RC_M 0x00000003
+#define AR_RTC_RC_MAC_WARM 0x00000001
+#define AR_RTC_RC_MAC_COLD 0x00000002
+#define AR_RTC_RC_COLD_RESET 0x00000004
+#define AR_RTC_RC_WARM_RESET 0x00000008
+
+#define AR_RTC_PLL_CONTROL \
+ (AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0014) : 0x7014
+
+#define AR_RTC_PLL_DIV 0x0000001f
+#define AR_RTC_PLL_DIV_S 0
+#define AR_RTC_PLL_DIV2 0x00000020
+#define AR_RTC_PLL_REFDIV_5 0x000000c0
+#define AR_RTC_PLL_CLKSEL 0x00000300
+#define AR_RTC_PLL_CLKSEL_S 8
+
+
+
+#define AR_RTC_RESET \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0040) : 0x7040)
+#define AR_RTC_RESET_EN (0x00000001)
+
+#define AR_RTC_STATUS \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0044) : 0x7044)
+
+#define AR_RTC_STATUS_M \
+ ((AR_SREV_9100(ah)) ? 0x0000003f : 0x0000000f)
+
+#define AR_RTC_PM_STATUS_M 0x0000000f
+
+#define AR_RTC_STATUS_SHUTDOWN 0x00000001
+#define AR_RTC_STATUS_ON 0x00000002
+#define AR_RTC_STATUS_SLEEP 0x00000004
+#define AR_RTC_STATUS_WAKEUP 0x00000008
+
+#define AR_RTC_SLEEP_CLK \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0048) : 0x7048)
+#define AR_RTC_FORCE_DERIVED_CLK 0x2
+
+#define AR_RTC_FORCE_WAKE \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x004c) : 0x704c)
+#define AR_RTC_FORCE_WAKE_EN 0x00000001
+#define AR_RTC_FORCE_WAKE_ON_INT 0x00000002
+
+
+#define AR_RTC_INTR_CAUSE \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0050) : 0x7050)
+
+#define AR_RTC_INTR_ENABLE \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0054) : 0x7054)
+
+#define AR_RTC_INTR_MASK \
+ ((AR_SREV_9100(ah)) ? (AR_RTC_BASE + 0x0058) : 0x7058)
+
+#define AR_SEQ_MASK 0x8060
+
+#define AR_AN_RF2G1_CH0 0x7810
+#define AR_AN_RF2G1_CH0_OB 0x03800000
+#define AR_AN_RF2G1_CH0_OB_S 23
+#define AR_AN_RF2G1_CH0_DB 0x1C000000
+#define AR_AN_RF2G1_CH0_DB_S 26
+
+#define AR_AN_RF5G1_CH0 0x7818
+#define AR_AN_RF5G1_CH0_OB5 0x00070000
+#define AR_AN_RF5G1_CH0_OB5_S 16
+#define AR_AN_RF5G1_CH0_DB5 0x00380000
+#define AR_AN_RF5G1_CH0_DB5_S 19
+
+#define AR_AN_RF2G1_CH1 0x7834
+#define AR_AN_RF2G1_CH1_OB 0x03800000
+#define AR_AN_RF2G1_CH1_OB_S 23
+#define AR_AN_RF2G1_CH1_DB 0x1C000000
+#define AR_AN_RF2G1_CH1_DB_S 26
+
+#define AR_AN_RF5G1_CH1 0x783C
+#define AR_AN_RF5G1_CH1_OB5 0x00070000
+#define AR_AN_RF5G1_CH1_OB5_S 16
+#define AR_AN_RF5G1_CH1_DB5 0x00380000
+#define AR_AN_RF5G1_CH1_DB5_S 19
+
+#define AR_AN_TOP2 0x7894
+#define AR_AN_TOP2_XPABIAS_LVL 0xC0000000
+#define AR_AN_TOP2_XPABIAS_LVL_S 30
+#define AR_AN_TOP2_LOCALBIAS 0x00200000
+#define AR_AN_TOP2_LOCALBIAS_S 21
+#define AR_AN_TOP2_PWDCLKIND 0x00400000
+#define AR_AN_TOP2_PWDCLKIND_S 22
+
+#define AR_AN_SYNTH9 0x7868
+#define AR_AN_SYNTH9_REFDIVA 0xf8000000
+#define AR_AN_SYNTH9_REFDIVA_S 27
+
+#define AR_STA_ID0 0x8000
+#define AR_STA_ID1 0x8004
+#define AR_STA_ID1_SADH_MASK 0x0000FFFF
+#define AR_STA_ID1_STA_AP 0x00010000
+#define AR_STA_ID1_ADHOC 0x00020000
+#define AR_STA_ID1_PWR_SAV 0x00040000
+#define AR_STA_ID1_KSRCHDIS 0x00080000
+#define AR_STA_ID1_PCF 0x00100000
+#define AR_STA_ID1_USE_DEFANT 0x00200000
+#define AR_STA_ID1_DEFANT_UPDATE 0x00400000
+#define AR_STA_ID1_RTS_USE_DEF 0x00800000
+#define AR_STA_ID1_ACKCTS_6MB 0x01000000
+#define AR_STA_ID1_BASE_RATE_11B 0x02000000
+#define AR_STA_ID1_SECTOR_SELF_GEN 0x04000000
+#define AR_STA_ID1_CRPT_MIC_ENABLE 0x08000000
+#define AR_STA_ID1_KSRCH_MODE 0x10000000
+#define AR_STA_ID1_PRESERVE_SEQNUM 0x20000000
+#define AR_STA_ID1_CBCIV_ENDIAN 0x40000000
+#define AR_STA_ID1_MCAST_KSRCH 0x80000000
+
+#define AR_BSS_ID0 0x8008
+#define AR_BSS_ID1 0x800C
+#define AR_BSS_ID1_U16 0x0000FFFF
+#define AR_BSS_ID1_AID 0x07FF0000
+#define AR_BSS_ID1_AID_S 16
+
+#define AR_BCN_RSSI_AVE 0x8010
+#define AR_BCN_RSSI_AVE_MASK 0x00000FFF
+
+#define AR_TIME_OUT 0x8014
+#define AR_TIME_OUT_ACK 0x00003FFF
+#define AR_TIME_OUT_ACK_S 0
+#define AR_TIME_OUT_CTS 0x3FFF0000
+#define AR_TIME_OUT_CTS_S 16
+
+#define AR_RSSI_THR 0x8018
+#define AR_RSSI_THR_MASK 0x000000FF
+#define AR_RSSI_THR_BM_THR 0x0000FF00
+#define AR_RSSI_THR_BM_THR_S 8
+#define AR_RSSI_BCN_WEIGHT 0x1F000000
+#define AR_RSSI_BCN_WEIGHT_S 24
+#define AR_RSSI_BCN_RSSI_RST 0x20000000
+
+#define AR_USEC 0x801c
+#define AR_USEC_USEC 0x0000007F
+#define AR_USEC_TX_LAT 0x007FC000
+#define AR_USEC_TX_LAT_S 14
+#define AR_USEC_RX_LAT 0x1F800000
+#define AR_USEC_RX_LAT_S 23
+
+#define AR_RESET_TSF 0x8020
+#define AR_RESET_TSF_ONCE 0x01000000
+
+#define AR_MAX_CFP_DUR 0x8038
+#define AR_CFP_VAL 0x0000FFFF
+
+#define AR_RX_FILTER 0x803C
+#define AR_RX_FILTER_ALL 0x00000000
+#define AR_RX_UCAST 0x00000001
+#define AR_RX_MCAST 0x00000002
+#define AR_RX_BCAST 0x00000004
+#define AR_RX_CONTROL 0x00000008
+#define AR_RX_BEACON 0x00000010
+#define AR_RX_PROM 0x00000020
+#define AR_RX_PROBE_REQ 0x00000080
+#define AR_RX_MY_BEACON 0x00000200
+#define AR_RX_COMPR_BAR 0x00000400
+#define AR_RX_COMPR_BA 0x00000800
+#define AR_RX_UNCOM_BA_BAR 0x00001000
+
+#define AR_MCAST_FIL0 0x8040
+#define AR_MCAST_FIL1 0x8044
+
+#define AR_DIAG_SW 0x8048
+#define AR_DIAG_CACHE_ACK 0x00000001
+#define AR_DIAG_ACK_DIS 0x00000002
+#define AR_DIAG_CTS_DIS 0x00000004
+#define AR_DIAG_ENCRYPT_DIS 0x00000008
+#define AR_DIAG_DECRYPT_DIS 0x00000010
+#define AR_DIAG_RX_DIS 0x00000020
+#define AR_DIAG_LOOP_BACK 0x00000040
+#define AR_DIAG_CORR_FCS 0x00000080
+#define AR_DIAG_CHAN_INFO 0x00000100
+#define AR_DIAG_SCRAM_SEED 0x0001FE00
+#define AR_DIAG_SCRAM_SEED_S 8
+#define AR_DIAG_FRAME_NV0 0x00020000
+#define AR_DIAG_OBS_PT_SEL1 0x000C0000
+#define AR_DIAG_OBS_PT_SEL1_S 18
+#define AR_DIAG_FORCE_RX_CLEAR 0x00100000
+#define AR_DIAG_IGNORE_VIRT_CS 0x00200000
+#define AR_DIAG_FORCE_CH_IDLE_HIGH 0x00400000
+#define AR_DIAG_EIFS_CTRL_ENA 0x00800000
+#define AR_DIAG_DUAL_CHAIN_INFO 0x01000000
+#define AR_DIAG_RX_ABORT 0x02000000
+#define AR_DIAG_SATURATE_CYCLE_CNT 0x04000000
+#define AR_DIAG_OBS_PT_SEL2 0x08000000
+#define AR_DIAG_RX_CLEAR_CTL_LOW 0x10000000
+#define AR_DIAG_RX_CLEAR_EXT_LOW 0x20000000
+
+#define AR_TSF_L32 0x804c
+#define AR_TSF_U32 0x8050
+
+#define AR_TST_ADDAC 0x8054
+#define AR_DEF_ANTENNA 0x8058
+
+#define AR_AES_MUTE_MASK0 0x805c
+#define AR_AES_MUTE_MASK0_FC 0x0000FFFF
+#define AR_AES_MUTE_MASK0_QOS 0xFFFF0000
+#define AR_AES_MUTE_MASK0_QOS_S 16
+
+#define AR_AES_MUTE_MASK1 0x8060
+#define AR_AES_MUTE_MASK1_SEQ 0x0000FFFF
+
+#define AR_GATED_CLKS 0x8064
+#define AR_GATED_CLKS_TX 0x00000002
+#define AR_GATED_CLKS_RX 0x00000004
+#define AR_GATED_CLKS_REG 0x00000008
+
+#define AR_OBS_BUS_CTRL 0x8068
+#define AR_OBS_BUS_SEL_1 0x00040000
+#define AR_OBS_BUS_SEL_2 0x00080000
+#define AR_OBS_BUS_SEL_3 0x000C0000
+#define AR_OBS_BUS_SEL_4 0x08040000
+#define AR_OBS_BUS_SEL_5 0x08080000
+
+#define AR_OBS_BUS_1 0x806c
+#define AR_OBS_BUS_1_PCU 0x00000001
+#define AR_OBS_BUS_1_RX_END 0x00000002
+#define AR_OBS_BUS_1_RX_WEP 0x00000004
+#define AR_OBS_BUS_1_RX_BEACON 0x00000008
+#define AR_OBS_BUS_1_RX_FILTER 0x00000010
+#define AR_OBS_BUS_1_TX_HCF 0x00000020
+#define AR_OBS_BUS_1_QUIET_TIME 0x00000040
+#define AR_OBS_BUS_1_CHAN_IDLE 0x00000080
+#define AR_OBS_BUS_1_TX_HOLD 0x00000100
+#define AR_OBS_BUS_1_TX_FRAME 0x00000200
+#define AR_OBS_BUS_1_RX_FRAME 0x00000400
+#define AR_OBS_BUS_1_RX_CLEAR 0x00000800
+#define AR_OBS_BUS_1_WEP_STATE 0x0003F000
+#define AR_OBS_BUS_1_WEP_STATE_S 12
+#define AR_OBS_BUS_1_RX_STATE 0x01F00000
+#define AR_OBS_BUS_1_RX_STATE_S 20
+#define AR_OBS_BUS_1_TX_STATE 0x7E000000
+#define AR_OBS_BUS_1_TX_STATE_S 25
+
+#define AR_LAST_TSTP 0x8080
+#define AR_NAV 0x8084
+#define AR_RTS_OK 0x8088
+#define AR_RTS_FAIL 0x808c
+#define AR_ACK_FAIL 0x8090
+#define AR_FCS_FAIL 0x8094
+#define AR_BEACON_CNT 0x8098
+
+#define AR_SLEEP1 0x80d4
+#define AR_SLEEP1_ASSUME_DTIM 0x00080000
+#define AR_SLEEP1_CAB_TIMEOUT 0xFFE00000
+#define AR_SLEEP1_CAB_TIMEOUT_S 21
+
+#define AR_SLEEP2 0x80d8
+#define AR_SLEEP2_BEACON_TIMEOUT 0xFFE00000
+#define AR_SLEEP2_BEACON_TIMEOUT_S 21
+
+#define AR_BSSMSKL 0x80e0
+#define AR_BSSMSKU 0x80e4
+
+#define AR_TPC 0x80e8
+#define AR_TPC_ACK 0x0000003f
+#define AR_TPC_ACK_S 0x00
+#define AR_TPC_CTS 0x00003f00
+#define AR_TPC_CTS_S 0x08
+#define AR_TPC_CHIRP 0x003f0000
+#define AR_TPC_CHIRP_S 0x16
+
+#define AR_TFCNT 0x80ec
+#define AR_RFCNT 0x80f0
+#define AR_RCCNT 0x80f4
+#define AR_CCCNT 0x80f8
+
+#define AR_QUIET1 0x80fc
+#define AR_QUIET1_NEXT_QUIET_S 0
+#define AR_QUIET1_NEXT_QUIET_M 0x0000ffff
+#define AR_QUIET1_QUIET_ENABLE 0x00010000
+#define AR_QUIET1_QUIET_ACK_CTS_ENABLE 0x00020000
+#define AR_QUIET2 0x8100
+#define AR_QUIET2_QUIET_PERIOD_S 0
+#define AR_QUIET2_QUIET_PERIOD_M 0x0000ffff
+#define AR_QUIET2_QUIET_DUR_S 16
+#define AR_QUIET2_QUIET_DUR 0xffff0000
+
+#define AR_TSF_PARM 0x8104
+#define AR_TSF_INCREMENT_M 0x000000ff
+#define AR_TSF_INCREMENT_S 0x00
+
+#define AR_QOS_NO_ACK 0x8108
+#define AR_QOS_NO_ACK_TWO_BIT 0x0000000f
+#define AR_QOS_NO_ACK_TWO_BIT_S 0
+#define AR_QOS_NO_ACK_BIT_OFF 0x00000070
+#define AR_QOS_NO_ACK_BIT_OFF_S 4
+#define AR_QOS_NO_ACK_BYTE_OFF 0x00000180
+#define AR_QOS_NO_ACK_BYTE_OFF_S 7
+
+#define AR_PHY_ERR 0x810c
+
+#define AR_PHY_ERR_DCHIRP 0x00000008
+#define AR_PHY_ERR_RADAR 0x00000020
+#define AR_PHY_ERR_OFDM_TIMING 0x00020000
+#define AR_PHY_ERR_CCK_TIMING 0x02000000
+
+#define AR_RXFIFO_CFG 0x8114
+
+
+#define AR_MIC_QOS_CONTROL 0x8118
+#define AR_MIC_QOS_SELECT 0x811c
+
+#define AR_PCU_MISC 0x8120
+#define AR_PCU_FORCE_BSSID_MATCH 0x00000001
+#define AR_PCU_MIC_NEW_LOC_ENA 0x00000004
+#define AR_PCU_TX_ADD_TSF 0x00000008
+#define AR_PCU_CCK_SIFS_MODE 0x00000010
+#define AR_PCU_RX_ANT_UPDT 0x00000800
+#define AR_PCU_TXOP_TBTT_LIMIT_ENA 0x00001000
+#define AR_PCU_MISS_BCN_IN_SLEEP 0x00004000
+#define AR_PCU_BUG_12306_FIX_ENA 0x00020000
+#define AR_PCU_FORCE_QUIET_COLL 0x00040000
+#define AR_PCU_TBTT_PROTECT 0x00200000
+#define AR_PCU_CLEAR_VMF 0x01000000
+#define AR_PCU_CLEAR_BA_VALID 0x04000000
+
+
+#define AR_FILT_OFDM 0x8124
+#define AR_FILT_OFDM_COUNT 0x00FFFFFF
+
+#define AR_FILT_CCK 0x8128
+#define AR_FILT_CCK_COUNT 0x00FFFFFF
+
+#define AR_PHY_ERR_1 0x812c
+#define AR_PHY_ERR_1_COUNT 0x00FFFFFF
+#define AR_PHY_ERR_MASK_1 0x8130
+
+#define AR_PHY_ERR_2 0x8134
+#define AR_PHY_ERR_2_COUNT 0x00FFFFFF
+#define AR_PHY_ERR_MASK_2 0x8138
+
+#define AR_PHY_COUNTMAX (3 << 22)
+#define AR_MIBCNT_INTRMASK (3 << 22)
+
+#define AR_TSF_THRESHOLD 0x813c
+#define AR_TSF_THRESHOLD_VAL 0x0000FFFF
+
+#define AR_PHY_ERR_EIFS_MASK 8144
+
+#define AR_PHY_ERR_3 0x8168
+#define AR_PHY_ERR_3_COUNT 0x00FFFFFF
+#define AR_PHY_ERR_MASK_3 0x816c
+
+#define AR_TXSIFS 0x81d0
+#define AR_TXSIFS_TIME 0x000000FF
+#define AR_TXSIFS_TX_LATENCY 0x00000F00
+#define AR_TXSIFS_TX_LATENCY_S 8
+#define AR_TXSIFS_ACK_SHIFT 0x00007000
+#define AR_TXSIFS_ACK_SHIFT_S 12
+
+#define AR_TXOP_X 0x81ec
+#define AR_TXOP_X_VAL 0x000000FF
+
+
+#define AR_TXOP_0_3 0x81f0
+#define AR_TXOP_4_7 0x81f4
+#define AR_TXOP_8_11 0x81f8
+#define AR_TXOP_12_15 0x81fc
+
+
+#define AR_NEXT_TBTT_TIMER 0x8200
+#define AR_NEXT_DMA_BEACON_ALERT 0x8204
+#define AR_NEXT_SWBA 0x8208
+#define AR_NEXT_CFP 0x8208
+#define AR_NEXT_HCF 0x820C
+#define AR_NEXT_TIM 0x8210
+#define AR_NEXT_DTIM 0x8214
+#define AR_NEXT_QUIET_TIMER 0x8218
+#define AR_NEXT_NDP_TIMER 0x821C
+
+#define AR_BEACON_PERIOD 0x8220
+#define AR_DMA_BEACON_PERIOD 0x8224
+#define AR_SWBA_PERIOD 0x8228
+#define AR_HCF_PERIOD 0x822C
+#define AR_TIM_PERIOD 0x8230
+#define AR_DTIM_PERIOD 0x8234
+#define AR_QUIET_PERIOD 0x8238
+#define AR_NDP_PERIOD 0x823C
+
+#define AR_TIMER_MODE 0x8240
+#define AR_TBTT_TIMER_EN 0x00000001
+#define AR_DBA_TIMER_EN 0x00000002
+#define AR_SWBA_TIMER_EN 0x00000004
+#define AR_HCF_TIMER_EN 0x00000008
+#define AR_TIM_TIMER_EN 0x00000010
+#define AR_DTIM_TIMER_EN 0x00000020
+#define AR_QUIET_TIMER_EN 0x00000040
+#define AR_NDP_TIMER_EN 0x00000080
+#define AR_TIMER_OVERFLOW_INDEX 0x00000700
+#define AR_TIMER_OVERFLOW_INDEX_S 8
+#define AR_TIMER_THRESH 0xFFFFF000
+#define AR_TIMER_THRESH_S 12
+
+#define AR_SLP32_MODE 0x8244
+#define AR_SLP32_HALF_CLK_LATENCY 0x000FFFFF
+#define AR_SLP32_ENA 0x00100000
+#define AR_SLP32_TSF_WRITE_STATUS 0x00200000
+
+#define AR_SLP32_WAKE 0x8248
+#define AR_SLP32_WAKE_XTL_TIME 0x0000FFFF
+
+#define AR_SLP32_INC 0x824c
+#define AR_SLP32_TST_INC 0x000FFFFF
+
+#define AR_SLP_CNT 0x8250
+#define AR_SLP_CYCLE_CNT 0x8254
+
+#define AR_SLP_MIB_CTRL 0x8258
+#define AR_SLP_MIB_CLEAR 0x00000001
+#define AR_SLP_MIB_PENDING 0x00000002
+
+#define AR_2040_MODE 0x8318
+#define AR_2040_JOINED_RX_CLEAR 0x00000001
+
+
+#define AR_EXTRCCNT 0x8328
+
+#define AR_SELFGEN_MASK 0x832c
+
+#define AR_PCU_TXBUF_CTRL 0x8340
+#define AR_PCU_TXBUF_CTRL_SIZE_MASK 0x7FF
+#define AR_PCU_TXBUF_CTRL_USABLE_SIZE 0x700
+#define AR_9285_PCU_TXBUF_CTRL_USABLE_SIZE 0x380
+
+#define AR_KEYTABLE_0 0x8800
+#define AR_KEYTABLE(_n) (AR_KEYTABLE_0 + ((_n)*32))
+#define AR_KEY_CACHE_SIZE 128
+#define AR_RSVD_KEYTABLE_ENTRIES 4
+#define AR_KEY_TYPE 0x00000007
+#define AR_KEYTABLE_TYPE_40 0x00000000
+#define AR_KEYTABLE_TYPE_104 0x00000001
+#define AR_KEYTABLE_TYPE_128 0x00000003
+#define AR_KEYTABLE_TYPE_TKIP 0x00000004
+#define AR_KEYTABLE_TYPE_AES 0x00000005
+#define AR_KEYTABLE_TYPE_CCM 0x00000006
+#define AR_KEYTABLE_TYPE_CLR 0x00000007
+#define AR_KEYTABLE_ANT 0x00000008
+#define AR_KEYTABLE_VALID 0x00008000
+#define AR_KEYTABLE_KEY0(_n) (AR_KEYTABLE(_n) + 0)
+#define AR_KEYTABLE_KEY1(_n) (AR_KEYTABLE(_n) + 4)
+#define AR_KEYTABLE_KEY2(_n) (AR_KEYTABLE(_n) + 8)
+#define AR_KEYTABLE_KEY3(_n) (AR_KEYTABLE(_n) + 12)
+#define AR_KEYTABLE_KEY4(_n) (AR_KEYTABLE(_n) + 16)
+#define AR_KEYTABLE_TYPE(_n) (AR_KEYTABLE(_n) + 20)
+#define AR_KEYTABLE_MAC0(_n) (AR_KEYTABLE(_n) + 24)
+#define AR_KEYTABLE_MAC1(_n) (AR_KEYTABLE(_n) + 28)
+
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include "core.h"
+#include "hw.h"
+#include "regd.h"
+#include "regd_common.h"
+
+static int ath9k_regd_chansort(const void *a, const void *b)
+{
+ const struct ath9k_channel *ca = a;
+ const struct ath9k_channel *cb = b;
+
+ return (ca->channel == cb->channel) ?
+ (ca->channelFlags & CHAN_FLAGS) -
+ (cb->channelFlags & CHAN_FLAGS) : ca->channel - cb->channel;
+}
+
+static void
+ath9k_regd_sort(void *a, u32 n, u32 size, ath_hal_cmp_t *cmp)
+{
+ u8 *aa = a;
+ u8 *ai, *t;
+
+ for (ai = aa + size; --n >= 1; ai += size)
+ for (t = ai; t > aa; t -= size) {
+ u8 *u = t - size;
+ if (cmp(u, t) <= 0)
+ break;
+ swap(u, t, size);
+ }
+}
+
+static u16 ath9k_regd_get_eepromRD(struct ath_hal *ah)
+{
+ return ah->ah_currentRD & ~WORLDWIDE_ROAMING_FLAG;
+}
+
+static bool ath9k_regd_is_chan_bm_zero(u64 *bitmask)
+{
+ int i;
+
+ for (i = 0; i < BMLEN; i++) {
+ if (bitmask[i] != 0)
+ return false;
+ }
+ return true;
+}
+
+static bool ath9k_regd_is_eeprom_valid(struct ath_hal *ah)
+{
+ u16 rd = ath9k_regd_get_eepromRD(ah);
+ int i;
+
+ if (rd & COUNTRY_ERD_FLAG) {
+ u16 cc = rd & ~COUNTRY_ERD_FLAG;
+ for (i = 0; i < ARRAY_SIZE(allCountries); i++)
+ if (allCountries[i].countryCode == cc)
+ return true;
+ } else {
+ for (i = 0; i < ARRAY_SIZE(regDomainPairs); i++)
+ if (regDomainPairs[i].regDmnEnum == rd)
+ return true;
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: invalid regulatory domain/country code 0x%x\n",
+ __func__, rd);
+ return false;
+}
+
+static bool ath9k_regd_is_fcc_midband_supported(struct ath_hal *ah)
+{
+ u32 regcap;
+
+ regcap = ah->ah_caps.reg_cap;
+
+ if (regcap & AR_EEPROM_EEREGCAP_EN_FCC_MIDBAND)
+ return true;
+ else
+ return false;
+}
+
+static bool ath9k_regd_is_ccode_valid(struct ath_hal *ah,
+ u16 cc)
+{
+ u16 rd;
+ int i;
+
+ if (cc == CTRY_DEFAULT)
+ return true;
+ if (cc == CTRY_DEBUG)
+ return true;
+
+ rd = ath9k_regd_get_eepromRD(ah);
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY, "%s: EEPROM regdomain 0x%x\n",
+ __func__, rd);
+
+ if (rd & COUNTRY_ERD_FLAG) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: EEPROM setting is country code %u\n",
+ __func__, rd & ~COUNTRY_ERD_FLAG);
+ return cc == (rd & ~COUNTRY_ERD_FLAG);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(allCountries); i++) {
+ if (cc == allCountries[i].countryCode) {
+#ifdef AH_SUPPORT_11D
+ if ((rd & WORLD_SKU_MASK) == WORLD_SKU_PREFIX)
+ return true;
+#endif
+ if (allCountries[i].regDmnEnum == rd ||
+ rd == DEBUG_REG_DMN || rd == NO_ENUMRD)
+ return true;
+ }
+ }
+ return false;
+}
+
+static void
+ath9k_regd_get_wmodes_nreg(struct ath_hal *ah,
+ struct country_code_to_enum_rd *country,
+ struct regDomain *rd5GHz,
+ unsigned long *modes_allowed)
+{
+ bitmap_copy(modes_allowed, ah->ah_caps.wireless_modes, ATH9K_MODE_MAX);
+
+ if (test_bit(ATH9K_MODE_11G, ah->ah_caps.wireless_modes) &&
+ (!country->allow11g))
+ clear_bit(ATH9K_MODE_11G, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11A, ah->ah_caps.wireless_modes) &&
+ (ath9k_regd_is_chan_bm_zero(rd5GHz->chan11a)))
+ clear_bit(ATH9K_MODE_11A, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NG_HT20, ah->ah_caps.wireless_modes)
+ && (!country->allow11ng20))
+ clear_bit(ATH9K_MODE_11NG_HT20, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NA_HT20, ah->ah_caps.wireless_modes)
+ && (!country->allow11na20))
+ clear_bit(ATH9K_MODE_11NA_HT20, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NG_HT40PLUS, ah->ah_caps.wireless_modes) &&
+ (!country->allow11ng40))
+ clear_bit(ATH9K_MODE_11NG_HT40PLUS, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NG_HT40MINUS, ah->ah_caps.wireless_modes) &&
+ (!country->allow11ng40))
+ clear_bit(ATH9K_MODE_11NG_HT40MINUS, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NA_HT40PLUS, ah->ah_caps.wireless_modes) &&
+ (!country->allow11na40))
+ clear_bit(ATH9K_MODE_11NA_HT40PLUS, modes_allowed);
+
+ if (test_bit(ATH9K_MODE_11NA_HT40MINUS, ah->ah_caps.wireless_modes) &&
+ (!country->allow11na40))
+ clear_bit(ATH9K_MODE_11NA_HT40MINUS, modes_allowed);
+}
+
+bool ath9k_regd_is_public_safety_sku(struct ath_hal *ah)
+{
+ u16 rd;
+
+ rd = ath9k_regd_get_eepromRD(ah);
+
+ switch (rd) {
+ case FCC4_FCCA:
+ case (CTRY_UNITED_STATES_FCC49 | COUNTRY_ERD_FLAG):
+ return true;
+ case DEBUG_REG_DMN:
+ case NO_ENUMRD:
+ if (ah->ah_countryCode == CTRY_UNITED_STATES_FCC49)
+ return true;
+ break;
+ }
+ return false;
+}
+
+static struct country_code_to_enum_rd*
+ath9k_regd_find_country(u16 countryCode)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(allCountries); i++) {
+ if (allCountries[i].countryCode == countryCode)
+ return &allCountries[i];
+ }
+ return NULL;
+}
+
+static u16 ath9k_regd_get_default_country(struct ath_hal *ah)
+{
+ u16 rd;
+ int i;
+
+ rd = ath9k_regd_get_eepromRD(ah);
+ if (rd & COUNTRY_ERD_FLAG) {
+ struct country_code_to_enum_rd *country = NULL;
+ u16 cc = rd & ~COUNTRY_ERD_FLAG;
+
+ country = ath9k_regd_find_country(cc);
+ if (country != NULL)
+ return cc;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(regDomainPairs); i++)
+ if (regDomainPairs[i].regDmnEnum == rd) {
+ if (regDomainPairs[i].singleCC != 0)
+ return regDomainPairs[i].singleCC;
+ else
+ i = ARRAY_SIZE(regDomainPairs);
+ }
+ return CTRY_DEFAULT;
+}
+
+static bool ath9k_regd_is_valid_reg_domain(int regDmn,
+ struct regDomain *rd)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(regDomains); i++) {
+ if (regDomains[i].regDmnEnum == regDmn) {
+ if (rd != NULL) {
+ memcpy(rd, ®Domains[i],
+ sizeof(struct regDomain));
+ }
+ return true;
+ }
+ }
+ return false;
+}
+
+static bool ath9k_regd_is_valid_reg_domainPair(int regDmnPair)
+{
+ int i;
+
+ if (regDmnPair == NO_ENUMRD)
+ return false;
+ for (i = 0; i < ARRAY_SIZE(regDomainPairs); i++) {
+ if (regDomainPairs[i].regDmnEnum == regDmnPair)
+ return true;
+ }
+ return false;
+}
+
+static bool
+ath9k_regd_get_wmode_regdomain(struct ath_hal *ah, int regDmn,
+ u16 channelFlag, struct regDomain *rd)
+{
+ int i, found;
+ u64 flags = NO_REQ;
+ struct reg_dmn_pair_mapping *regPair = NULL;
+ int regOrg;
+
+ regOrg = regDmn;
+ if (regDmn == CTRY_DEFAULT) {
+ u16 rdnum;
+ rdnum = ath9k_regd_get_eepromRD(ah);
+
+ if (!(rdnum & COUNTRY_ERD_FLAG)) {
+ if (ath9k_regd_is_valid_reg_domain(rdnum, NULL) ||
+ ath9k_regd_is_valid_reg_domainPair(rdnum)) {
+ regDmn = rdnum;
+ }
+ }
+ }
+
+ if ((regDmn & MULTI_DOMAIN_MASK) == 0) {
+ for (i = 0, found = 0;
+ (i < ARRAY_SIZE(regDomainPairs)) && (!found); i++) {
+ if (regDomainPairs[i].regDmnEnum == regDmn) {
+ regPair = ®DomainPairs[i];
+ found = 1;
+ }
+ }
+ if (!found) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Failed to find reg domain pair %u\n",
+ __func__, regDmn);
+ return false;
+ }
+ if (!(channelFlag & CHANNEL_2GHZ)) {
+ regDmn = regPair->regDmn5GHz;
+ flags = regPair->flags5GHz;
+ }
+ if (channelFlag & CHANNEL_2GHZ) {
+ regDmn = regPair->regDmn2GHz;
+ flags = regPair->flags2GHz;
+ }
+ }
+
+ found = ath9k_regd_is_valid_reg_domain(regDmn, rd);
+ if (!found) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Failed to find unitary reg domain %u\n",
+ __func__, regDmn);
+ return false;
+ } else {
+ rd->pscan &= regPair->pscanMask;
+ if (((regOrg & MULTI_DOMAIN_MASK) == 0) &&
+ (flags != NO_REQ)) {
+ rd->flags = flags;
+ }
+
+ rd->flags &= (channelFlag & CHANNEL_2GHZ) ?
+ REG_DOMAIN_2GHZ_MASK : REG_DOMAIN_5GHZ_MASK;
+ return true;
+ }
+}
+
+static bool ath9k_regd_is_bit_set(int bit, u64 *bitmask)
+{
+ int byteOffset, bitnum;
+ u64 val;
+
+ byteOffset = bit / 64;
+ bitnum = bit - byteOffset * 64;
+ val = ((u64) 1) << bitnum;
+ if (bitmask[byteOffset] & val)
+ return true;
+ else
+ return false;
+}
+
+static void
+ath9k_regd_add_reg_classid(u8 *regclassids, u32 maxregids,
+ u32 *nregids, u8 regclassid)
+{
+ int i;
+
+ if (regclassid == 0)
+ return;
+
+ for (i = 0; i < maxregids; i++) {
+ if (regclassids[i] == regclassid)
+ return;
+ if (regclassids[i] == 0)
+ break;
+ }
+
+ if (i == maxregids)
+ return;
+ else {
+ regclassids[i] = regclassid;
+ *nregids += 1;
+ }
+
+ return;
+}
+
+static bool
+ath9k_regd_get_eeprom_reg_ext_bits(struct ath_hal *ah,
+ enum reg_ext_bitmap bit)
+{
+ return (ah->ah_currentRDExt & (1 << bit)) ? true : false;
+}
+
+#ifdef ATH_NF_PER_CHAN
+
+static void ath9k_regd_init_rf_buffer(struct ath9k_channel *ichans,
+ int nchans)
+{
+ int i, j, next;
+
+ for (next = 0; next < nchans; next++) {
+ for (i = 0; i < NUM_NF_READINGS; i++) {
+ ichans[next].nfCalHist[i].currIndex = 0;
+ ichans[next].nfCalHist[i].privNF =
+ AR_PHY_CCA_MAX_GOOD_VALUE;
+ ichans[next].nfCalHist[i].invalidNFcount =
+ AR_PHY_CCA_FILTERWINDOW_LENGTH;
+ for (j = 0; j < ATH9K_NF_CAL_HIST_MAX; j++) {
+ ichans[next].nfCalHist[i].nfCalBuffer[j] =
+ AR_PHY_CCA_MAX_GOOD_VALUE;
+ }
+ }
+ }
+}
+#endif
+
+static int ath9k_regd_is_chan_present(struct ath_hal *ah,
+ u16 c)
+{
+ int i;
+
+ for (i = 0; i < 150; i++) {
+ if (!ah->ah_channels[i].channel)
+ return -1;
+ else if (ah->ah_channels[i].channel == c)
+ return i;
+ }
+
+ return -1;
+}
+
+static bool
+ath9k_regd_add_channel(struct ath_hal *ah,
+ u16 c,
+ u16 c_lo,
+ u16 c_hi,
+ u16 maxChan,
+ u8 ctl,
+ int pos,
+ struct regDomain rd5GHz,
+ struct RegDmnFreqBand *fband,
+ struct regDomain *rd,
+ const struct cmode *cm,
+ struct ath9k_channel *ichans,
+ bool enableExtendedChannels)
+{
+ struct ath9k_channel *chan;
+ int ret;
+ u32 channelFlags = 0;
+ u8 privFlags = 0;
+
+ if (!(c_lo <= c && c <= c_hi)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: c %u out of range [%u..%u]\n",
+ __func__, c, c_lo, c_hi);
+ return false;
+ }
+ if ((fband->channelBW == CHANNEL_HALF_BW) &&
+ !(ah->ah_caps.hw_caps & ATH9K_HW_CAP_CHAN_HALFRATE)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Skipping %u half rate channel\n",
+ __func__, c);
+ return false;
+ }
+
+ if ((fband->channelBW == CHANNEL_QUARTER_BW) &&
+ !(ah->ah_caps.hw_caps & ATH9K_HW_CAP_CHAN_QUARTERRATE)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Skipping %u quarter rate channel\n",
+ __func__, c);
+ return false;
+ }
+
+ if (((c + fband->channelSep) / 2) > (maxChan + HALF_MAXCHANBW)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: c %u > maxChan %u\n",
+ __func__, c, maxChan);
+ return false;
+ }
+
+ if ((fband->usePassScan & IS_ECM_CHAN) && !enableExtendedChannels) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Skipping ecm channel\n");
+ return false;
+ }
+
+ if ((rd->flags & NO_HOSTAP) && (ah->ah_opmode == ATH9K_M_HOSTAP)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Skipping HOSTAP channel\n");
+ return false;
+ }
+
+ if (IS_HT40_MODE(cm->mode) &&
+ !(ath9k_regd_get_eeprom_reg_ext_bits(ah, REG_EXT_FCC_DFS_HT40)) &&
+ (fband->useDfs) &&
+ (rd->conformanceTestLimit != MKK)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Skipping HT40 channel (en_fcc_dfs_ht40 = 0)\n");
+ return false;
+ }
+
+ if (IS_HT40_MODE(cm->mode) &&
+ !(ath9k_regd_get_eeprom_reg_ext_bits(ah,
+ REG_EXT_JAPAN_NONDFS_HT40)) &&
+ !(fband->useDfs) && (rd->conformanceTestLimit == MKK)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Skipping HT40 channel (en_jap_ht40 = 0)\n");
+ return false;
+ }
+
+ if (IS_HT40_MODE(cm->mode) &&
+ !(ath9k_regd_get_eeprom_reg_ext_bits(ah, REG_EXT_JAPAN_DFS_HT40)) &&
+ (fband->useDfs) &&
+ (rd->conformanceTestLimit == MKK)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Skipping HT40 channel (en_jap_dfs_ht40 = 0)\n");
+ return false;
+ }
+
+ /* Calculate channel flags */
+
+ channelFlags = cm->flags;
+
+ switch (fband->channelBW) {
+ case CHANNEL_HALF_BW:
+ channelFlags |= CHANNEL_HALF;
+ break;
+ case CHANNEL_QUARTER_BW:
+ channelFlags |= CHANNEL_QUARTER;
+ break;
+ }
+
+ if (fband->usePassScan & rd->pscan)
+ channelFlags |= CHANNEL_PASSIVE;
+ else
+ channelFlags &= ~CHANNEL_PASSIVE;
+ if (fband->useDfs & rd->dfsMask)
+ privFlags = CHANNEL_DFS;
+ else
+ privFlags = 0;
+ if (rd->flags & LIMIT_FRAME_4MS)
+ privFlags |= CHANNEL_4MS_LIMIT;
+ if (privFlags & CHANNEL_DFS)
+ privFlags |= CHANNEL_DISALLOW_ADHOC;
+ if (rd->flags & ADHOC_PER_11D)
+ privFlags |= CHANNEL_PER_11D_ADHOC;
+
+ if (channelFlags & CHANNEL_PASSIVE) {
+ if ((c < 2412) || (c > 2462)) {
+ if (rd5GHz.regDmnEnum == MKK1 ||
+ rd5GHz.regDmnEnum == MKK2) {
+ u32 regcap = ah->ah_caps.reg_cap;
+ if (!(regcap &
+ (AR_EEPROM_EEREGCAP_EN_KK_U1_EVEN |
+ AR_EEPROM_EEREGCAP_EN_KK_U2 |
+ AR_EEPROM_EEREGCAP_EN_KK_MIDBAND)) &&
+ isUNII1OddChan(c)) {
+ channelFlags &= ~CHANNEL_PASSIVE;
+ } else {
+ privFlags |= CHANNEL_DISALLOW_ADHOC;
+ }
+ } else {
+ privFlags |= CHANNEL_DISALLOW_ADHOC;
+ }
+ }
+ }
+
+ if ((cm->mode == ATH9K_MODE_11A) ||
+ (cm->mode == ATH9K_MODE_11NA_HT20) ||
+ (cm->mode == ATH9K_MODE_11NA_HT40PLUS) ||
+ (cm->mode == ATH9K_MODE_11NA_HT40MINUS)) {
+ if (rd->flags & (ADHOC_NO_11A | DISALLOW_ADHOC_11A))
+ privFlags |= CHANNEL_DISALLOW_ADHOC;
+ }
+
+ /* Fill in channel details */
+
+ ret = ath9k_regd_is_chan_present(ah, c);
+ if (ret == -1) {
+ chan = &ah->ah_channels[pos];
+ chan->channel = c;
+ chan->maxRegTxPower = fband->powerDfs;
+ chan->antennaMax = fband->antennaMax;
+ chan->regDmnFlags = rd->flags;
+ chan->maxTxPower = AR5416_MAX_RATE_POWER;
+ chan->minTxPower = AR5416_MAX_RATE_POWER;
+ chan->channelFlags = channelFlags;
+ chan->privFlags = privFlags;
+ } else {
+ chan = &ah->ah_channels[ret];
+ chan->channelFlags |= channelFlags;
+ chan->privFlags |= privFlags;
+ }
+
+ /* Set CTLs */
+
+ if ((cm->flags & CHANNEL_ALL) == CHANNEL_A)
+ chan->conformanceTestLimit[0] = ctl;
+ else if ((cm->flags & CHANNEL_ALL) == CHANNEL_B)
+ chan->conformanceTestLimit[1] = ctl;
+ else if ((cm->flags & CHANNEL_ALL) == CHANNEL_G)
+ chan->conformanceTestLimit[2] = ctl;
+
+ return (ret == -1) ? true : false;
+}
+
+static bool ath9k_regd_japan_check(struct ath_hal *ah,
+ int b,
+ struct regDomain *rd5GHz)
+{
+ bool skipband = false;
+ int i;
+ u32 regcap;
+
+ for (i = 0; i < ARRAY_SIZE(j_bandcheck); i++) {
+ if (j_bandcheck[i].freqbandbit == b) {
+ regcap = ah->ah_caps.reg_cap;
+ if ((j_bandcheck[i].eepromflagtocheck & regcap) == 0) {
+ skipband = true;
+ } else if ((regcap & AR_EEPROM_EEREGCAP_EN_KK_U2) ||
+ (regcap & AR_EEPROM_EEREGCAP_EN_KK_MIDBAND)) {
+ rd5GHz->dfsMask |= DFS_MKK4;
+ rd5GHz->pscan |= PSCAN_MKK3;
+ }
+ break;
+ }
+ }
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Skipping %d freq band\n",
+ __func__, j_bandcheck[i].freqbandbit);
+
+ return skipband;
+}
+
+bool
+ath9k_regd_init_channels(struct ath_hal *ah,
+ u32 maxchans,
+ u32 *nchans, u8 *regclassids,
+ u32 maxregids, u32 *nregids, u16 cc,
+ bool enableOutdoor,
+ bool enableExtendedChannels)
+{
+ u16 maxChan = 7000;
+ struct country_code_to_enum_rd *country = NULL;
+ struct regDomain rd5GHz, rd2GHz;
+ const struct cmode *cm;
+ struct ath9k_channel *ichans = &ah->ah_channels[0];
+ int next = 0, b;
+ u8 ctl;
+ int regdmn;
+ u16 chanSep;
+ unsigned long *modes_avail;
+ DECLARE_BITMAP(modes_allowed, ATH9K_MODE_MAX);
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY, "%s: cc %u %s %s\n",
+ __func__, cc,
+ enableOutdoor ? "Enable outdoor" : "",
+ enableExtendedChannels ? "Enable ecm" : "");
+
+ if (!ath9k_regd_is_ccode_valid(ah, cc)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: invalid country code %d\n", __func__, cc);
+ return false;
+ }
+
+ if (!ath9k_regd_is_eeprom_valid(ah)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: invalid EEPROM contents\n", __func__);
+ return false;
+ }
+
+ ah->ah_countryCode = ath9k_regd_get_default_country(ah);
+
+ if (ah->ah_countryCode == CTRY_DEFAULT) {
+ ah->ah_countryCode = cc & COUNTRY_CODE_MASK;
+ if ((ah->ah_countryCode == CTRY_DEFAULT) &&
+ (ath9k_regd_get_eepromRD(ah) == CTRY_DEFAULT)) {
+ ah->ah_countryCode = CTRY_UNITED_STATES;
+ }
+ }
+
+#ifdef AH_SUPPORT_11D
+ if (ah->ah_countryCode == CTRY_DEFAULT) {
+ regdmn = ath9k_regd_get_eepromRD(ah);
+ country = NULL;
+ } else {
+#endif
+ country = ath9k_regd_find_country(ah->ah_countryCode);
+ if (country == NULL) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "Country is NULL!!!!, cc= %d\n",
+ ah->ah_countryCode);
+ return false;
+ } else {
+ regdmn = country->regDmnEnum;
+#ifdef AH_SUPPORT_11D
+ if (((ath9k_regd_get_eepromRD(ah) &
+ WORLD_SKU_MASK) == WORLD_SKU_PREFIX) &&
+ (cc == CTRY_UNITED_STATES)) {
+ if (!isWwrSKU_NoMidband(ah)
+ && ath9k_regd_is_fcc_midband_supported(ah))
+ regdmn = FCC3_FCCA;
+ else
+ regdmn = FCC1_FCCA;
+ }
+#endif
+ }
+#ifdef AH_SUPPORT_11D
+ }
+#endif
+ if (!ath9k_regd_get_wmode_regdomain(ah,
+ regdmn,
+ ~CHANNEL_2GHZ,
+ &rd5GHz)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: couldn't find unitary "
+ "5GHz reg domain for country %u\n",
+ __func__, ah->ah_countryCode);
+ return false;
+ }
+ if (!ath9k_regd_get_wmode_regdomain(ah,
+ regdmn,
+ CHANNEL_2GHZ,
+ &rd2GHz)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: couldn't find unitary 2GHz "
+ "reg domain for country %u\n",
+ __func__, ah->ah_countryCode);
+ return false;
+ }
+
+ if (!isWwrSKU(ah) && ((rd5GHz.regDmnEnum == FCC1) ||
+ (rd5GHz.regDmnEnum == FCC2))) {
+ if (ath9k_regd_is_fcc_midband_supported(ah)) {
+ if (!ath9k_regd_get_wmode_regdomain(ah,
+ FCC3_FCCA,
+ ~CHANNEL_2GHZ,
+ &rd5GHz)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: couldn't find unitary 5GHz "
+ "reg domain for country %u\n",
+ __func__, ah->ah_countryCode);
+ return false;
+ }
+ }
+ }
+
+ if (country == NULL) {
+ modes_avail = ah->ah_caps.wireless_modes;
+ } else {
+ ath9k_regd_get_wmodes_nreg(ah, country, &rd5GHz, modes_allowed);
+ modes_avail = modes_allowed;
+
+ if (!enableOutdoor)
+ maxChan = country->outdoorChanStart;
+ }
+
+ next = 0;
+
+ if (maxchans > ARRAY_SIZE(ah->ah_channels))
+ maxchans = ARRAY_SIZE(ah->ah_channels);
+
+ for (cm = modes; cm < &modes[ARRAY_SIZE(modes)]; cm++) {
+ u16 c, c_hi, c_lo;
+ u64 *channelBM = NULL;
+ struct regDomain *rd = NULL;
+ struct RegDmnFreqBand *fband = NULL, *freqs;
+ int8_t low_adj = 0, hi_adj = 0;
+
+ if (!test_bit(cm->mode, modes_avail)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: !avail mode %d flags 0x%x\n",
+ __func__, cm->mode, cm->flags);
+ continue;
+ }
+ if (!ath9k_get_channel_edges(ah, cm->flags, &c_lo, &c_hi)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: channels 0x%x not supported "
+ "by hardware\n",
+ __func__, cm->flags);
+ continue;
+ }
+
+ switch (cm->mode) {
+ case ATH9K_MODE_11A:
+ case ATH9K_MODE_11NA_HT20:
+ case ATH9K_MODE_11NA_HT40PLUS:
+ case ATH9K_MODE_11NA_HT40MINUS:
+ rd = &rd5GHz;
+ channelBM = rd->chan11a;
+ freqs = ®Dmn5GhzFreq[0];
+ ctl = rd->conformanceTestLimit;
+ break;
+ case ATH9K_MODE_11B:
+ rd = &rd2GHz;
+ channelBM = rd->chan11b;
+ freqs = ®Dmn2GhzFreq[0];
+ ctl = rd->conformanceTestLimit | CTL_11B;
+ break;
+ case ATH9K_MODE_11G:
+ case ATH9K_MODE_11NG_HT20:
+ case ATH9K_MODE_11NG_HT40PLUS:
+ case ATH9K_MODE_11NG_HT40MINUS:
+ rd = &rd2GHz;
+ channelBM = rd->chan11g;
+ freqs = ®Dmn2Ghz11gFreq[0];
+ ctl = rd->conformanceTestLimit | CTL_11G;
+ break;
+ default:
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: Unknown HAL mode 0x%x\n", __func__,
+ cm->mode);
+ continue;
+ }
+
+ if (ath9k_regd_is_chan_bm_zero(channelBM))
+ continue;
+
+ if ((cm->mode == ATH9K_MODE_11NA_HT40PLUS) ||
+ (cm->mode == ATH9K_MODE_11NG_HT40PLUS)) {
+ hi_adj = -20;
+ }
+
+ if ((cm->mode == ATH9K_MODE_11NA_HT40MINUS) ||
+ (cm->mode == ATH9K_MODE_11NG_HT40MINUS)) {
+ low_adj = 20;
+ }
+
+ /* XXX: Add a helper here instead */
+ for (b = 0; b < 64 * BMLEN; b++) {
+ if (ath9k_regd_is_bit_set(b, channelBM)) {
+ fband = &freqs[b];
+ if (rd5GHz.regDmnEnum == MKK1
+ || rd5GHz.regDmnEnum == MKK2) {
+ if (ath9k_regd_japan_check(ah,
+ b,
+ &rd5GHz))
+ continue;
+ }
+
+ ath9k_regd_add_reg_classid(regclassids,
+ maxregids,
+ nregids,
+ fband->
+ regClassId);
+
+ if (IS_HT40_MODE(cm->mode) && (rd == &rd5GHz)) {
+ chanSep = 40;
+ if (fband->lowChannel == 5280)
+ low_adj += 20;
+
+ if (fband->lowChannel == 5170)
+ continue;
+ } else
+ chanSep = fband->channelSep;
+
+ for (c = fband->lowChannel + low_adj;
+ ((c <= (fband->highChannel + hi_adj)) &&
+ (c >= (fband->lowChannel + low_adj)));
+ c += chanSep) {
+ if (next >= maxchans) {
+ DPRINTF(ah->ah_sc,
+ ATH_DBG_REGULATORY,
+ "%s: too many channels "
+ "for channel table\n",
+ __func__);
+ goto done;
+ }
+ if (ath9k_regd_add_channel(ah,
+ c, c_lo, c_hi,
+ maxChan, ctl,
+ next,
+ rd5GHz,
+ fband, rd, cm,
+ ichans,
+ enableExtendedChannels))
+ next++;
+ }
+ if (IS_HT40_MODE(cm->mode) &&
+ (fband->lowChannel == 5280)) {
+ low_adj -= 20;
+ }
+ }
+ }
+ }
+done:
+ if (next != 0) {
+ int i;
+
+ if (next > ARRAY_SIZE(ah->ah_channels)) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: too many channels %u; truncating to %u\n",
+ __func__, next,
+ (int) ARRAY_SIZE(ah->ah_channels));
+ next = ARRAY_SIZE(ah->ah_channels);
+ }
+#ifdef ATH_NF_PER_CHAN
+ ath9k_regd_init_rf_buffer(ichans, next);
+#endif
+ ath9k_regd_sort(ichans, next,
+ sizeof(struct ath9k_channel),
+ ath9k_regd_chansort);
+
+ ah->ah_nchan = next;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY, "Channel list:\n");
+ for (i = 0; i < next; i++) {
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "chan: %d flags: 0x%x\n",
+ ah->ah_channels[i].channel,
+ ah->ah_channels[i].channelFlags);
+ }
+ }
+ *nchans = next;
+
+ ah->ah_countryCode = ah->ah_countryCode;
+
+ ah->ah_currentRDInUse = regdmn;
+ ah->ah_currentRD5G = rd5GHz.regDmnEnum;
+ ah->ah_currentRD2G = rd2GHz.regDmnEnum;
+ if (country == NULL) {
+ ah->ah_iso[0] = 0;
+ ah->ah_iso[1] = 0;
+ } else {
+ ah->ah_iso[0] = country->isoName[0];
+ ah->ah_iso[1] = country->isoName[1];
+ }
+
+ return next != 0;
+}
+
+struct ath9k_channel*
+ath9k_regd_check_channel(struct ath_hal *ah,
+ const struct ath9k_channel *c)
+{
+ struct ath9k_channel *base, *cc;
+
+ int flags = c->channelFlags & CHAN_FLAGS;
+ int n, lim;
+
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: channel %u/0x%x (0x%x) requested\n", __func__,
+ c->channel, c->channelFlags, flags);
+
+ cc = ah->ah_curchan;
+ if (cc != NULL && cc->channel == c->channel &&
+ (cc->channelFlags & CHAN_FLAGS) == flags) {
+ if ((cc->privFlags & CHANNEL_INTERFERENCE) &&
+ (cc->privFlags & CHANNEL_DFS))
+ return NULL;
+ else
+ return cc;
+ }
+
+ base = ah->ah_channels;
+ n = ah->ah_nchan;
+
+ for (lim = n; lim != 0; lim >>= 1) {
+ int d;
+ cc = &base[lim >> 1];
+ d = c->channel - cc->channel;
+ if (d == 0) {
+ if ((cc->channelFlags & CHAN_FLAGS) == flags) {
+ if ((cc->privFlags & CHANNEL_INTERFERENCE) &&
+ (cc->privFlags & CHANNEL_DFS))
+ return NULL;
+ else
+ return cc;
+ }
+ d = flags - (cc->channelFlags & CHAN_FLAGS);
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY,
+ "%s: channel %u/0x%x d %d\n", __func__,
+ cc->channel, cc->channelFlags, d);
+ if (d > 0) {
+ base = cc + 1;
+ lim--;
+ }
+ }
+ DPRINTF(ah->ah_sc, ATH_DBG_REGULATORY, "%s: no match for %u/0x%x\n",
+ __func__, c->channel, c->channelFlags);
+ return NULL;
+}
+
+u32
+ath9k_regd_get_antenna_allowed(struct ath_hal *ah,
+ struct ath9k_channel *chan)
+{
+ struct ath9k_channel *ichan = NULL;
+
+ ichan = ath9k_regd_check_channel(ah, chan);
+ if (!ichan)
+ return 0;
+
+ return ichan->antennaMax;
+}
+
+u32 ath9k_regd_get_ctl(struct ath_hal *ah, struct ath9k_channel *chan)
+{
+ u32 ctl = NO_CTL;
+ struct ath9k_channel *ichan;
+
+ if (ah->ah_countryCode == CTRY_DEFAULT && isWwrSKU(ah)) {
+ if (IS_CHAN_B(chan))
+ ctl = SD_NO_CTL | CTL_11B;
+ else if (IS_CHAN_G(chan))
+ ctl = SD_NO_CTL | CTL_11G;
+ else
+ ctl = SD_NO_CTL | CTL_11A;
+ } else {
+ ichan = ath9k_regd_check_channel(ah, chan);
+ if (ichan != NULL) {
+ /* FIXME */
+ if (IS_CHAN_A(ichan))
+ ctl = ichan->conformanceTestLimit[0];
+ else if (IS_CHAN_B(ichan))
+ ctl = ichan->conformanceTestLimit[1];
+ else if (IS_CHAN_G(ichan))
+ ctl = ichan->conformanceTestLimit[2];
+
+ if (IS_CHAN_G(chan) && (ctl & 0xf) == CTL_11B)
+ ctl = (ctl & ~0xf) | CTL_11G;
+ }
+ }
+ return ctl;
+}
+
+void ath9k_regd_get_current_country(struct ath_hal *ah,
+ struct ath9k_country_entry *ctry)
+{
+ u16 rd = ath9k_regd_get_eepromRD(ah);
+
+ ctry->isMultidomain = false;
+ if (rd == CTRY_DEFAULT)
+ ctry->isMultidomain = true;
+ else if (!(rd & COUNTRY_ERD_FLAG))
+ ctry->isMultidomain = isWwrSKU(ah);
+
+ ctry->countryCode = ah->ah_countryCode;
+ ctry->regDmnEnum = ah->ah_currentRD;
+ ctry->regDmn5G = ah->ah_currentRD5G;
+ ctry->regDmn2G = ah->ah_currentRD2G;
+ ctry->iso[0] = ah->ah_iso[0];
+ ctry->iso[1] = ah->ah_iso[1];
+ ctry->iso[2] = ah->ah_iso[2];
+}
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef REGD_H
+#define REGD_H
+
+#include "ath9k.h"
+
+#define BMLEN 2
+#define BMZERO {(u64) 0, (u64) 0}
+
+#define BM(_fa, _fb, _fc, _fd, _fe, _ff, _fg, _fh, _fi, _fj, _fk, _fl) \
+ {((((_fa >= 0) && (_fa < 64)) ? \
+ (((u64) 1) << _fa) : (u64) 0) | \
+ (((_fb >= 0) && (_fb < 64)) ? \
+ (((u64) 1) << _fb) : (u64) 0) | \
+ (((_fc >= 0) && (_fc < 64)) ? \
+ (((u64) 1) << _fc) : (u64) 0) | \
+ (((_fd >= 0) && (_fd < 64)) ? \
+ (((u64) 1) << _fd) : (u64) 0) | \
+ (((_fe >= 0) && (_fe < 64)) ? \
+ (((u64) 1) << _fe) : (u64) 0) | \
+ (((_ff >= 0) && (_ff < 64)) ? \
+ (((u64) 1) << _ff) : (u64) 0) | \
+ (((_fg >= 0) && (_fg < 64)) ? \
+ (((u64) 1) << _fg) : (u64) 0) | \
+ (((_fh >= 0) && (_fh < 64)) ? \
+ (((u64) 1) << _fh) : (u64) 0) | \
+ (((_fi >= 0) && (_fi < 64)) ? \
+ (((u64) 1) << _fi) : (u64) 0) | \
+ (((_fj >= 0) && (_fj < 64)) ? \
+ (((u64) 1) << _fj) : (u64) 0) | \
+ (((_fk >= 0) && (_fk < 64)) ? \
+ (((u64) 1) << _fk) : (u64) 0) | \
+ (((_fl >= 0) && (_fl < 64)) ? \
+ (((u64) 1) << _fl) : (u64) 0) | \
+ ((((_fa > 63) && (_fa < 128)) ? \
+ (((u64) 1) << (_fa - 64)) : (u64) 0) | \
+ (((_fb > 63) && (_fb < 128)) ? \
+ (((u64) 1) << (_fb - 64)) : (u64) 0) | \
+ (((_fc > 63) && (_fc < 128)) ? \
+ (((u64) 1) << (_fc - 64)) : (u64) 0) | \
+ (((_fd > 63) && (_fd < 128)) ? \
+ (((u64) 1) << (_fd - 64)) : (u64) 0) | \
+ (((_fe > 63) && (_fe < 128)) ? \
+ (((u64) 1) << (_fe - 64)) : (u64) 0) | \
+ (((_ff > 63) && (_ff < 128)) ? \
+ (((u64) 1) << (_ff - 64)) : (u64) 0) | \
+ (((_fg > 63) && (_fg < 128)) ? \
+ (((u64) 1) << (_fg - 64)) : (u64) 0) | \
+ (((_fh > 63) && (_fh < 128)) ? \
+ (((u64) 1) << (_fh - 64)) : (u64) 0) | \
+ (((_fi > 63) && (_fi < 128)) ? \
+ (((u64) 1) << (_fi - 64)) : (u64) 0) | \
+ (((_fj > 63) && (_fj < 128)) ? \
+ (((u64) 1) << (_fj - 64)) : (u64) 0) | \
+ (((_fk > 63) && (_fk < 128)) ? \
+ (((u64) 1) << (_fk - 64)) : (u64) 0) | \
+ (((_fl > 63) && (_fl < 128)) ? \
+ (((u64) 1) << (_fl - 64)) : (u64) 0)))}
+
+#define DEF_REGDMN FCC1_FCCA
+#define DEF_DMN_5 FCC1
+#define DEF_DMN_2 FCCA
+#define COUNTRY_ERD_FLAG 0x8000
+#define WORLDWIDE_ROAMING_FLAG 0x4000
+#define SUPER_DOMAIN_MASK 0x0fff
+#define COUNTRY_CODE_MASK 0x3fff
+#define CF_INTERFERENCE (CHANNEL_CW_INT | CHANNEL_RADAR_INT)
+#define CHANNEL_14 (2484)
+#define IS_11G_CH14(_ch,_cf) \
+ (((_ch) == CHANNEL_14) && ((_cf) == CHANNEL_G))
+
+#define NO_PSCAN 0x0ULL
+#define PSCAN_FCC 0x0000000000000001ULL
+#define PSCAN_FCC_T 0x0000000000000002ULL
+#define PSCAN_ETSI 0x0000000000000004ULL
+#define PSCAN_MKK1 0x0000000000000008ULL
+#define PSCAN_MKK2 0x0000000000000010ULL
+#define PSCAN_MKKA 0x0000000000000020ULL
+#define PSCAN_MKKA_G 0x0000000000000040ULL
+#define PSCAN_ETSIA 0x0000000000000080ULL
+#define PSCAN_ETSIB 0x0000000000000100ULL
+#define PSCAN_ETSIC 0x0000000000000200ULL
+#define PSCAN_WWR 0x0000000000000400ULL
+#define PSCAN_MKKA1 0x0000000000000800ULL
+#define PSCAN_MKKA1_G 0x0000000000001000ULL
+#define PSCAN_MKKA2 0x0000000000002000ULL
+#define PSCAN_MKKA2_G 0x0000000000004000ULL
+#define PSCAN_MKK3 0x0000000000008000ULL
+#define PSCAN_DEFER 0x7FFFFFFFFFFFFFFFULL
+#define IS_ECM_CHAN 0x8000000000000000ULL
+
+#define isWwrSKU(_ah) \
+ (((ath9k_regd_get_eepromRD((_ah)) & WORLD_SKU_MASK) == \
+ WORLD_SKU_PREFIX) || \
+ (ath9k_regd_get_eepromRD(_ah) == WORLD))
+
+#define isWwrSKU_NoMidband(_ah) \
+ ((ath9k_regd_get_eepromRD((_ah)) == WOR3_WORLD) || \
+ (ath9k_regd_get_eepromRD(_ah) == WOR4_WORLD) || \
+ (ath9k_regd_get_eepromRD(_ah) == WOR5_ETSIC))
+
+#define isUNII1OddChan(ch) \
+ ((ch == 5170) || (ch == 5190) || (ch == 5210) || (ch == 5230))
+
+#define IS_HT40_MODE(_mode) \
+ (((_mode == ATH9K_MODE_11NA_HT40PLUS || \
+ _mode == ATH9K_MODE_11NG_HT40PLUS || \
+ _mode == ATH9K_MODE_11NA_HT40MINUS || \
+ _mode == ATH9K_MODE_11NG_HT40MINUS) ? true : false))
+
+#define CHAN_FLAGS (CHANNEL_ALL|CHANNEL_HALF|CHANNEL_QUARTER)
+
+#define swap(_a, _b, _size) { \
+ u8 *s = _b; \
+ int i = _size; \
+ do { \
+ u8 tmp = *_a; \
+ *_a++ = *s; \
+ *s++ = tmp; \
+ } while (--i); \
+ _a -= _size; \
+}
+
+
+#define HALF_MAXCHANBW 10
+
+#define MULTI_DOMAIN_MASK 0xFF00
+
+#define WORLD_SKU_MASK 0x00F0
+#define WORLD_SKU_PREFIX 0x0060
+
+#define CHANNEL_HALF_BW 10
+#define CHANNEL_QUARTER_BW 5
+
+typedef int ath_hal_cmp_t(const void *, const void *);
+
+struct reg_dmn_pair_mapping {
+ u16 regDmnEnum;
+ u16 regDmn5GHz;
+ u16 regDmn2GHz;
+ u32 flags5GHz;
+ u32 flags2GHz;
+ u64 pscanMask;
+ u16 singleCC;
+};
+
+struct ccmap {
+ char isoName[3];
+ u16 countryCode;
+};
+
+struct country_code_to_enum_rd {
+ u16 countryCode;
+ u16 regDmnEnum;
+ const char *isoName;
+ const char *name;
+ bool allow11g;
+ bool allow11aTurbo;
+ bool allow11gTurbo;
+ bool allow11ng20;
+ bool allow11ng40;
+ bool allow11na20;
+ bool allow11na40;
+ u16 outdoorChanStart;
+};
+
+struct RegDmnFreqBand {
+ u16 lowChannel;
+ u16 highChannel;
+ u8 powerDfs;
+ u8 antennaMax;
+ u8 channelBW;
+ u8 channelSep;
+ u64 useDfs;
+ u64 usePassScan;
+ u8 regClassId;
+};
+
+struct regDomain {
+ u16 regDmnEnum;
+ u8 conformanceTestLimit;
+ u64 dfsMask;
+ u64 pscan;
+ u32 flags;
+ u64 chan11a[BMLEN];
+ u64 chan11a_turbo[BMLEN];
+ u64 chan11a_dyn_turbo[BMLEN];
+ u64 chan11b[BMLEN];
+ u64 chan11g[BMLEN];
+ u64 chan11g_turbo[BMLEN];
+};
+
+struct cmode {
+ u32 mode;
+ u32 flags;
+};
+
+#define YES true
+#define NO false
+
+struct japan_bandcheck {
+ u16 freqbandbit;
+ u32 eepromflagtocheck;
+};
+
+struct common_mode_power {
+ u16 lchan;
+ u16 hchan;
+ u8 pwrlvl;
+};
+
+enum CountryCode {
+ CTRY_ALBANIA = 8,
+ CTRY_ALGERIA = 12,
+ CTRY_ARGENTINA = 32,
+ CTRY_ARMENIA = 51,
+ CTRY_AUSTRALIA = 36,
+ CTRY_AUSTRIA = 40,
+ CTRY_AZERBAIJAN = 31,
+ CTRY_BAHRAIN = 48,
+ CTRY_BELARUS = 112,
+ CTRY_BELGIUM = 56,
+ CTRY_BELIZE = 84,
+ CTRY_BOLIVIA = 68,
+ CTRY_BOSNIA_HERZ = 70,
+ CTRY_BRAZIL = 76,
+ CTRY_BRUNEI_DARUSSALAM = 96,
+ CTRY_BULGARIA = 100,
+ CTRY_CANADA = 124,
+ CTRY_CHILE = 152,
+ CTRY_CHINA = 156,
+ CTRY_COLOMBIA = 170,
+ CTRY_COSTA_RICA = 188,
+ CTRY_CROATIA = 191,
+ CTRY_CYPRUS = 196,
+ CTRY_CZECH = 203,
+ CTRY_DENMARK = 208,
+ CTRY_DOMINICAN_REPUBLIC = 214,
+ CTRY_ECUADOR = 218,
+ CTRY_EGYPT = 818,
+ CTRY_EL_SALVADOR = 222,
+ CTRY_ESTONIA = 233,
+ CTRY_FAEROE_ISLANDS = 234,
+ CTRY_FINLAND = 246,
+ CTRY_FRANCE = 250,
+ CTRY_GEORGIA = 268,
+ CTRY_GERMANY = 276,
+ CTRY_GREECE = 300,
+ CTRY_GUATEMALA = 320,
+ CTRY_HONDURAS = 340,
+ CTRY_HONG_KONG = 344,
+ CTRY_HUNGARY = 348,
+ CTRY_ICELAND = 352,
+ CTRY_INDIA = 356,
+ CTRY_INDONESIA = 360,
+ CTRY_IRAN = 364,
+ CTRY_IRAQ = 368,
+ CTRY_IRELAND = 372,
+ CTRY_ISRAEL = 376,
+ CTRY_ITALY = 380,
+ CTRY_JAMAICA = 388,
+ CTRY_JAPAN = 392,
+ CTRY_JORDAN = 400,
+ CTRY_KAZAKHSTAN = 398,
+ CTRY_KENYA = 404,
+ CTRY_KOREA_NORTH = 408,
+ CTRY_KOREA_ROC = 410,
+ CTRY_KOREA_ROC2 = 411,
+ CTRY_KOREA_ROC3 = 412,
+ CTRY_KUWAIT = 414,
+ CTRY_LATVIA = 428,
+ CTRY_LEBANON = 422,
+ CTRY_LIBYA = 434,
+ CTRY_LIECHTENSTEIN = 438,
+ CTRY_LITHUANIA = 440,
+ CTRY_LUXEMBOURG = 442,
+ CTRY_MACAU = 446,
+ CTRY_MACEDONIA = 807,
+ CTRY_MALAYSIA = 458,
+ CTRY_MALTA = 470,
+ CTRY_MEXICO = 484,
+ CTRY_MONACO = 492,
+ CTRY_MOROCCO = 504,
+ CTRY_NEPAL = 524,
+ CTRY_NETHERLANDS = 528,
+ CTRY_NETHERLANDS_ANTILLES = 530,
+ CTRY_NEW_ZEALAND = 554,
+ CTRY_NICARAGUA = 558,
+ CTRY_NORWAY = 578,
+ CTRY_OMAN = 512,
+ CTRY_PAKISTAN = 586,
+ CTRY_PANAMA = 591,
+ CTRY_PAPUA_NEW_GUINEA = 598,
+ CTRY_PARAGUAY = 600,
+ CTRY_PERU = 604,
+ CTRY_PHILIPPINES = 608,
+ CTRY_POLAND = 616,
+ CTRY_PORTUGAL = 620,
+ CTRY_PUERTO_RICO = 630,
+ CTRY_QATAR = 634,
+ CTRY_ROMANIA = 642,
+ CTRY_RUSSIA = 643,
+ CTRY_SAUDI_ARABIA = 682,
+ CTRY_SERBIA_MONTENEGRO = 891,
+ CTRY_SINGAPORE = 702,
+ CTRY_SLOVAKIA = 703,
+ CTRY_SLOVENIA = 705,
+ CTRY_SOUTH_AFRICA = 710,
+ CTRY_SPAIN = 724,
+ CTRY_SRI_LANKA = 144,
+ CTRY_SWEDEN = 752,
+ CTRY_SWITZERLAND = 756,
+ CTRY_SYRIA = 760,
+ CTRY_TAIWAN = 158,
+ CTRY_THAILAND = 764,
+ CTRY_TRINIDAD_Y_TOBAGO = 780,
+ CTRY_TUNISIA = 788,
+ CTRY_TURKEY = 792,
+ CTRY_UAE = 784,
+ CTRY_UKRAINE = 804,
+ CTRY_UNITED_KINGDOM = 826,
+ CTRY_UNITED_STATES = 840,
+ CTRY_UNITED_STATES_FCC49 = 842,
+ CTRY_URUGUAY = 858,
+ CTRY_UZBEKISTAN = 860,
+ CTRY_VENEZUELA = 862,
+ CTRY_VIET_NAM = 704,
+ CTRY_YEMEN = 887,
+ CTRY_ZIMBABWE = 716,
+ CTRY_JAPAN1 = 393,
+ CTRY_JAPAN2 = 394,
+ CTRY_JAPAN3 = 395,
+ CTRY_JAPAN4 = 396,
+ CTRY_JAPAN5 = 397,
+ CTRY_JAPAN6 = 4006,
+ CTRY_JAPAN7 = 4007,
+ CTRY_JAPAN8 = 4008,
+ CTRY_JAPAN9 = 4009,
+ CTRY_JAPAN10 = 4010,
+ CTRY_JAPAN11 = 4011,
+ CTRY_JAPAN12 = 4012,
+ CTRY_JAPAN13 = 4013,
+ CTRY_JAPAN14 = 4014,
+ CTRY_JAPAN15 = 4015,
+ CTRY_JAPAN16 = 4016,
+ CTRY_JAPAN17 = 4017,
+ CTRY_JAPAN18 = 4018,
+ CTRY_JAPAN19 = 4019,
+ CTRY_JAPAN20 = 4020,
+ CTRY_JAPAN21 = 4021,
+ CTRY_JAPAN22 = 4022,
+ CTRY_JAPAN23 = 4023,
+ CTRY_JAPAN24 = 4024,
+ CTRY_JAPAN25 = 4025,
+ CTRY_JAPAN26 = 4026,
+ CTRY_JAPAN27 = 4027,
+ CTRY_JAPAN28 = 4028,
+ CTRY_JAPAN29 = 4029,
+ CTRY_JAPAN30 = 4030,
+ CTRY_JAPAN31 = 4031,
+ CTRY_JAPAN32 = 4032,
+ CTRY_JAPAN33 = 4033,
+ CTRY_JAPAN34 = 4034,
+ CTRY_JAPAN35 = 4035,
+ CTRY_JAPAN36 = 4036,
+ CTRY_JAPAN37 = 4037,
+ CTRY_JAPAN38 = 4038,
+ CTRY_JAPAN39 = 4039,
+ CTRY_JAPAN40 = 4040,
+ CTRY_JAPAN41 = 4041,
+ CTRY_JAPAN42 = 4042,
+ CTRY_JAPAN43 = 4043,
+ CTRY_JAPAN44 = 4044,
+ CTRY_JAPAN45 = 4045,
+ CTRY_JAPAN46 = 4046,
+ CTRY_JAPAN47 = 4047,
+ CTRY_JAPAN48 = 4048,
+ CTRY_JAPAN49 = 4049,
+ CTRY_JAPAN50 = 4050,
+ CTRY_JAPAN51 = 4051,
+ CTRY_JAPAN52 = 4052,
+ CTRY_JAPAN53 = 4053,
+ CTRY_JAPAN54 = 4054,
+ CTRY_JAPAN55 = 4055,
+ CTRY_JAPAN56 = 4056,
+ CTRY_JAPAN57 = 4057,
+ CTRY_JAPAN58 = 4058,
+ CTRY_JAPAN59 = 4059,
+ CTRY_AUSTRALIA2 = 5000,
+ CTRY_CANADA2 = 5001,
+ CTRY_BELGIUM2 = 5002
+};
+
+void ath9k_regd_get_current_country(struct ath_hal *ah,
+ struct ath9k_country_entry *ctry);
+
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef REGD_COMMON_H
+#define REGD_COMMON_H
+
+enum EnumRd {
+ NO_ENUMRD = 0x00,
+ NULL1_WORLD = 0x03,
+ NULL1_ETSIB = 0x07,
+ NULL1_ETSIC = 0x08,
+ FCC1_FCCA = 0x10,
+ FCC1_WORLD = 0x11,
+ FCC4_FCCA = 0x12,
+ FCC5_FCCA = 0x13,
+ FCC6_FCCA = 0x14,
+
+ FCC2_FCCA = 0x20,
+ FCC2_WORLD = 0x21,
+ FCC2_ETSIC = 0x22,
+ FCC6_WORLD = 0x23,
+ FRANCE_RES = 0x31,
+ FCC3_FCCA = 0x3A,
+ FCC3_WORLD = 0x3B,
+
+ ETSI1_WORLD = 0x37,
+ ETSI3_ETSIA = 0x32,
+ ETSI2_WORLD = 0x35,
+ ETSI3_WORLD = 0x36,
+ ETSI4_WORLD = 0x30,
+ ETSI4_ETSIC = 0x38,
+ ETSI5_WORLD = 0x39,
+ ETSI6_WORLD = 0x34,
+ ETSI_RESERVED = 0x33,
+
+ MKK1_MKKA = 0x40,
+ MKK1_MKKB = 0x41,
+ APL4_WORLD = 0x42,
+ MKK2_MKKA = 0x43,
+ APL_RESERVED = 0x44,
+ APL2_WORLD = 0x45,
+ APL2_APLC = 0x46,
+ APL3_WORLD = 0x47,
+ MKK1_FCCA = 0x48,
+ APL2_APLD = 0x49,
+ MKK1_MKKA1 = 0x4A,
+ MKK1_MKKA2 = 0x4B,
+ MKK1_MKKC = 0x4C,
+
+ APL3_FCCA = 0x50,
+ APL1_WORLD = 0x52,
+ APL1_FCCA = 0x53,
+ APL1_APLA = 0x54,
+ APL1_ETSIC = 0x55,
+ APL2_ETSIC = 0x56,
+ APL5_WORLD = 0x58,
+ APL6_WORLD = 0x5B,
+ APL7_FCCA = 0x5C,
+ APL8_WORLD = 0x5D,
+ APL9_WORLD = 0x5E,
+
+ WOR0_WORLD = 0x60,
+ WOR1_WORLD = 0x61,
+ WOR2_WORLD = 0x62,
+ WOR3_WORLD = 0x63,
+ WOR4_WORLD = 0x64,
+ WOR5_ETSIC = 0x65,
+
+ WOR01_WORLD = 0x66,
+ WOR02_WORLD = 0x67,
+ EU1_WORLD = 0x68,
+
+ WOR9_WORLD = 0x69,
+ WORA_WORLD = 0x6A,
+ WORB_WORLD = 0x6B,
+
+ MKK3_MKKB = 0x80,
+ MKK3_MKKA2 = 0x81,
+ MKK3_MKKC = 0x82,
+
+ MKK4_MKKB = 0x83,
+ MKK4_MKKA2 = 0x84,
+ MKK4_MKKC = 0x85,
+
+ MKK5_MKKB = 0x86,
+ MKK5_MKKA2 = 0x87,
+ MKK5_MKKC = 0x88,
+
+ MKK6_MKKB = 0x89,
+ MKK6_MKKA2 = 0x8A,
+ MKK6_MKKC = 0x8B,
+
+ MKK7_MKKB = 0x8C,
+ MKK7_MKKA2 = 0x8D,
+ MKK7_MKKC = 0x8E,
+
+ MKK8_MKKB = 0x8F,
+ MKK8_MKKA2 = 0x90,
+ MKK8_MKKC = 0x91,
+
+ MKK14_MKKA1 = 0x92,
+ MKK15_MKKA1 = 0x93,
+
+ MKK10_FCCA = 0xD0,
+ MKK10_MKKA1 = 0xD1,
+ MKK10_MKKC = 0xD2,
+ MKK10_MKKA2 = 0xD3,
+
+ MKK11_MKKA = 0xD4,
+ MKK11_FCCA = 0xD5,
+ MKK11_MKKA1 = 0xD6,
+ MKK11_MKKC = 0xD7,
+ MKK11_MKKA2 = 0xD8,
+
+ MKK12_MKKA = 0xD9,
+ MKK12_FCCA = 0xDA,
+ MKK12_MKKA1 = 0xDB,
+ MKK12_MKKC = 0xDC,
+ MKK12_MKKA2 = 0xDD,
+
+ MKK13_MKKB = 0xDE,
+
+ MKK3_MKKA = 0xF0,
+ MKK3_MKKA1 = 0xF1,
+ MKK3_FCCA = 0xF2,
+ MKK4_MKKA = 0xF3,
+ MKK4_MKKA1 = 0xF4,
+ MKK4_FCCA = 0xF5,
+ MKK9_MKKA = 0xF6,
+ MKK10_MKKA = 0xF7,
+ MKK6_MKKA1 = 0xF8,
+ MKK6_FCCA = 0xF9,
+ MKK7_MKKA1 = 0xFA,
+ MKK7_FCCA = 0xFB,
+ MKK9_FCCA = 0xFC,
+ MKK9_MKKA1 = 0xFD,
+ MKK9_MKKC = 0xFE,
+ MKK9_MKKA2 = 0xFF,
+
+ APL1 = 0x0150,
+ APL2 = 0x0250,
+ APL3 = 0x0350,
+ APL4 = 0x0450,
+ APL5 = 0x0550,
+ APL6 = 0x0650,
+ APL7 = 0x0750,
+ APL8 = 0x0850,
+ APL9 = 0x0950,
+ APL10 = 0x1050,
+
+ ETSI1 = 0x0130,
+ ETSI2 = 0x0230,
+ ETSI3 = 0x0330,
+ ETSI4 = 0x0430,
+ ETSI5 = 0x0530,
+ ETSI6 = 0x0630,
+ ETSIA = 0x0A30,
+ ETSIB = 0x0B30,
+ ETSIC = 0x0C30,
+
+ FCC1 = 0x0110,
+ FCC2 = 0x0120,
+ FCC3 = 0x0160,
+ FCC4 = 0x0165,
+ FCC5 = 0x0510,
+ FCC6 = 0x0610,
+ FCCA = 0x0A10,
+
+ APLD = 0x0D50,
+
+ MKK1 = 0x0140,
+ MKK2 = 0x0240,
+ MKK3 = 0x0340,
+ MKK4 = 0x0440,
+ MKK5 = 0x0540,
+ MKK6 = 0x0640,
+ MKK7 = 0x0740,
+ MKK8 = 0x0840,
+ MKK9 = 0x0940,
+ MKK10 = 0x0B40,
+ MKK11 = 0x1140,
+ MKK12 = 0x1240,
+ MKK13 = 0x0C40,
+ MKK14 = 0x1440,
+ MKK15 = 0x1540,
+ MKKA = 0x0A40,
+ MKKC = 0x0A50,
+
+ NULL1 = 0x0198,
+ WORLD = 0x0199,
+ DEBUG_REG_DMN = 0x01ff,
+};
+
+enum {
+ FCC = 0x10,
+ MKK = 0x40,
+ ETSI = 0x30,
+};
+
+enum {
+ NO_REQ = 0x00000000,
+ DISALLOW_ADHOC_11A = 0x00000001,
+ DISALLOW_ADHOC_11A_TURB = 0x00000002,
+ NEED_NFC = 0x00000004,
+
+ ADHOC_PER_11D = 0x00000008,
+ ADHOC_NO_11A = 0x00000010,
+
+ PUBLIC_SAFETY_DOMAIN = 0x00000020,
+ LIMIT_FRAME_4MS = 0x00000040,
+
+ NO_HOSTAP = 0x00000080,
+
+ REQ_MASK = 0x000000FF,
+};
+
+#define REG_DOMAIN_2GHZ_MASK (REQ_MASK & \
+ (!(ADHOC_NO_11A | DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB)))
+#define REG_DOMAIN_5GHZ_MASK REQ_MASK
+
+static struct reg_dmn_pair_mapping regDomainPairs[] = {
+ {NO_ENUMRD, DEBUG_REG_DMN, DEBUG_REG_DMN, NO_REQ, NO_REQ,
+ PSCAN_DEFER, 0},
+ {NULL1_WORLD, NULL1, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {NULL1_ETSIB, NULL1, ETSIB, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {NULL1_ETSIC, NULL1, ETSIC, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+
+ {FCC2_FCCA, FCC2, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC2_WORLD, FCC2, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC2_ETSIC, FCC2, ETSIC, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC3_FCCA, FCC3, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC3_WORLD, FCC3, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC4_FCCA, FCC4, FCCA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {FCC5_FCCA, FCC5, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC6_FCCA, FCC6, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC6_WORLD, FCC6, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+
+ {ETSI1_WORLD, ETSI1, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {ETSI2_WORLD, ETSI2, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {ETSI3_WORLD, ETSI3, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {ETSI4_WORLD, ETSI4, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {ETSI5_WORLD, ETSI5, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {ETSI6_WORLD, ETSI6, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+
+ {ETSI3_ETSIA, ETSI3, WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {FRANCE_RES, ETSI3, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+
+ {FCC1_WORLD, FCC1, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {FCC1_FCCA, FCC1, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL1_WORLD, APL1, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL2_WORLD, APL2, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL3_WORLD, APL3, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL4_WORLD, APL4, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL5_WORLD, APL5, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL6_WORLD, APL6, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL8_WORLD, APL8, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL9_WORLD, APL9, WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+
+ {APL3_FCCA, APL3, FCCA, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL1_ETSIC, APL1, ETSIC, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL2_ETSIC, APL2, ETSIC, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {APL2_APLD, APL2, APLD, NO_REQ, NO_REQ, PSCAN_DEFER,},
+
+ {MKK1_MKKA, MKK1, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA, CTRY_JAPAN},
+ {MKK1_MKKB, MKK1, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKK1 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN1},
+ {MKK1_FCCA, MKK1, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1, CTRY_JAPAN2},
+ {MKK1_MKKA1, MKK1, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN4},
+ {MKK1_MKKA2, MKK1, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN5},
+ {MKK1_MKKC, MKK1, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1, CTRY_JAPAN6},
+
+ {MKK2_MKKA, MKK2, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKK2 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN3},
+
+ {MKK3_MKKA, MKK3, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA, CTRY_JAPAN25},
+ {MKK3_MKKB, MKK3, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN7},
+ {MKK3_MKKA1, MKK3, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN26},
+ {MKK3_MKKA2, MKK3, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN8},
+ {MKK3_MKKC, MKK3, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN9},
+ {MKK3_FCCA, MKK3, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN27},
+
+ {MKK4_MKKA, MKK4, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN36},
+ {MKK4_MKKB, MKK4, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN10},
+ {MKK4_MKKA1, MKK4, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN28},
+ {MKK4_MKKA2, MKK4, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN11},
+ {MKK4_MKKC, MKK4, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN12},
+ {MKK4_FCCA, MKK4, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN29},
+
+ {MKK5_MKKB, MKK5, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN13},
+ {MKK5_MKKA2, MKK5, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN14},
+ {MKK5_MKKC, MKK5, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN15},
+
+ {MKK6_MKKB, MKK6, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA | PSCAN_MKKA_G, CTRY_JAPAN16},
+ {MKK6_MKKA1, MKK6, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN30},
+ {MKK6_MKKA2, MKK6, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN17},
+ {MKK6_MKKC, MKK6, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1, CTRY_JAPAN18},
+ {MKK6_FCCA, MKK6, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN31},
+
+ {MKK7_MKKB, MKK7, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN19},
+ {MKK7_MKKA1, MKK7, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN32},
+ {MKK7_MKKA2, MKK7, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G,
+ CTRY_JAPAN20},
+ {MKK7_MKKC, MKK7, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN21},
+ {MKK7_FCCA, MKK7, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN33},
+
+ {MKK8_MKKB, MKK8, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN22},
+ {MKK8_MKKA2, MKK8, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G,
+ CTRY_JAPAN23},
+ {MKK8_MKKC, MKK8, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN24},
+
+ {MKK9_MKKA, MKK9, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK2 | PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN34},
+ {MKK9_FCCA, MKK9, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN37},
+ {MKK9_MKKA1, MKK9, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN38},
+ {MKK9_MKKA2, MKK9, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN40},
+ {MKK9_MKKC, MKK9, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN39},
+
+ {MKK10_MKKA, MKK10, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC, PSCAN_MKK2 | PSCAN_MKK3, CTRY_JAPAN35},
+ {MKK10_FCCA, MKK10, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN41},
+ {MKK10_MKKA1, MKK10, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN42},
+ {MKK10_MKKA2, MKK10, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN44},
+ {MKK10_MKKC, MKK10, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ NO_PSCAN, CTRY_JAPAN43},
+
+ {MKK11_MKKA, MKK11, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN45},
+ {MKK11_FCCA, MKK11, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN46},
+ {MKK11_MKKA1, MKK11, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN47},
+ {MKK11_MKKA2, MKK11, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G, CTRY_JAPAN49},
+ {MKK11_MKKC, MKK11, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK3, CTRY_JAPAN48},
+
+ {MKK12_MKKA, MKK12, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN50},
+ {MKK12_FCCA, MKK12, FCCA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN51},
+ {MKK12_MKKA1, MKK12, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA1 | PSCAN_MKKA1_G,
+ CTRY_JAPAN52},
+ {MKK12_MKKA2, MKK12, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA2 | PSCAN_MKKA2_G,
+ CTRY_JAPAN54},
+ {MKK12_MKKC, MKK12, MKKC,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3, CTRY_JAPAN53},
+
+ {MKK13_MKKB, MKK13, MKKA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB | NEED_NFC |
+ LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKK3 | PSCAN_MKKA | PSCAN_MKKA_G,
+ CTRY_JAPAN57},
+
+ {MKK14_MKKA1, MKK14, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN58},
+ {MKK15_MKKA1, MKK15, MKKA,
+ DISALLOW_ADHOC_11A_TURB | NEED_NFC | LIMIT_FRAME_4MS, NEED_NFC,
+ PSCAN_MKK1 | PSCAN_MKKA1 | PSCAN_MKKA1_G, CTRY_JAPAN59},
+
+ {WOR0_WORLD, WOR0_WORLD, WOR0_WORLD, NO_REQ, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WOR1_WORLD, WOR1_WORLD, WOR1_WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WOR2_WORLD, WOR2_WORLD, WOR2_WORLD, DISALLOW_ADHOC_11A_TURB,
+ NO_REQ, PSCAN_DEFER, 0},
+ {WOR3_WORLD, WOR3_WORLD, WOR3_WORLD, NO_REQ, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WOR4_WORLD, WOR4_WORLD, WOR4_WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WOR5_ETSIC, WOR5_ETSIC, WOR5_ETSIC,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WOR01_WORLD, WOR01_WORLD, WOR01_WORLD, NO_REQ, NO_REQ,
+ PSCAN_DEFER, 0},
+ {WOR02_WORLD, WOR02_WORLD, WOR02_WORLD, NO_REQ, NO_REQ,
+ PSCAN_DEFER, 0},
+ {EU1_WORLD, EU1_WORLD, EU1_WORLD, NO_REQ, NO_REQ, PSCAN_DEFER, 0},
+ {WOR9_WORLD, WOR9_WORLD, WOR9_WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WORA_WORLD, WORA_WORLD, WORA_WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+ {WORB_WORLD, WORB_WORLD, WORB_WORLD,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB, NO_REQ, PSCAN_DEFER,
+ 0},
+};
+
+#define NO_INTERSECT_REQ 0xFFFFFFFF
+#define NO_UNION_REQ 0
+
+static struct country_code_to_enum_rd allCountries[] = {
+ {CTRY_DEBUG, NO_ENUMRD, "DB", "DEBUG", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_DEFAULT, DEF_REGDMN, "NA", "NO_COUNTRY_SET", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_ALBANIA, NULL1_WORLD, "AL", "ALBANIA", YES, NO, YES, YES, NO,
+ NO, NO, 7000},
+ {CTRY_ALGERIA, NULL1_WORLD, "DZ", "ALGERIA", YES, NO, YES, YES, NO,
+ NO, NO, 7000},
+ {CTRY_ARGENTINA, APL3_WORLD, "AR", "ARGENTINA", YES, NO, NO, YES,
+ NO, YES, NO, 7000},
+ {CTRY_ARMENIA, ETSI4_WORLD, "AM", "ARMENIA", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_AUSTRALIA, FCC2_WORLD, "AU", "AUSTRALIA", YES, YES, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_AUSTRALIA2, FCC6_WORLD, "AU", "AUSTRALIA2", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_AUSTRIA, ETSI1_WORLD, "AT", "AUSTRIA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_AZERBAIJAN, ETSI4_WORLD, "AZ", "AZERBAIJAN", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_BAHRAIN, APL6_WORLD, "BH", "BAHRAIN", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_BELARUS, ETSI1_WORLD, "BY", "BELARUS", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_BELGIUM, ETSI1_WORLD, "BE", "BELGIUM", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_BELGIUM2, ETSI4_WORLD, "BL", "BELGIUM", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_BELIZE, APL1_ETSIC, "BZ", "BELIZE", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_BOLIVIA, APL1_ETSIC, "BO", "BOLVIA", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_BOSNIA_HERZ, ETSI1_WORLD, "BA", "BOSNIA_HERZGOWINA", YES, NO,
+ YES, YES, YES, YES, NO, 7000},
+ {CTRY_BRAZIL, FCC3_WORLD, "BR", "BRAZIL", YES, NO, NO, YES, NO,
+ YES, NO, 7000},
+ {CTRY_BRUNEI_DARUSSALAM, APL1_WORLD, "BN", "BRUNEI DARUSSALAM",
+ YES, YES, YES, YES, YES, YES, YES, 7000},
+ {CTRY_BULGARIA, ETSI6_WORLD, "BG", "BULGARIA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_CANADA, FCC2_FCCA, "CA", "CANADA", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_CANADA2, FCC6_FCCA, "CA", "CANADA2", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_CHILE, APL6_WORLD, "CL", "CHILE", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_CHINA, APL1_WORLD, "CN", "CHINA", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_COLOMBIA, FCC1_FCCA, "CO", "COLOMBIA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_COSTA_RICA, FCC1_WORLD, "CR", "COSTA RICA", YES, NO, YES,
+ YES, YES, YES, NO, 7000},
+ {CTRY_CROATIA, ETSI3_WORLD, "HR", "CROATIA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_CYPRUS, ETSI1_WORLD, "CY", "CYPRUS", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_CZECH, ETSI3_WORLD, "CZ", "CZECH REPUBLIC", YES, NO, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_DENMARK, ETSI1_WORLD, "DK", "DENMARK", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_DOMINICAN_REPUBLIC, FCC1_FCCA, "DO", "DOMINICAN REPUBLIC",
+ YES, YES, YES, YES, YES, YES, YES, 7000},
+ {CTRY_ECUADOR, FCC1_WORLD, "EC", "ECUADOR", YES, NO, NO, YES, YES,
+ YES, NO, 7000},
+ {CTRY_EGYPT, ETSI3_WORLD, "EG", "EGYPT", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_EL_SALVADOR, FCC1_WORLD, "SV", "EL SALVADOR", YES, NO, YES,
+ YES, YES, YES, NO, 7000},
+ {CTRY_ESTONIA, ETSI1_WORLD, "EE", "ESTONIA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_FINLAND, ETSI1_WORLD, "FI", "FINLAND", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_FRANCE, ETSI1_WORLD, "FR", "FRANCE", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_GEORGIA, ETSI4_WORLD, "GE", "GEORGIA", YES, YES, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_GERMANY, ETSI1_WORLD, "DE", "GERMANY", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_GREECE, ETSI1_WORLD, "GR", "GREECE", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_GUATEMALA, FCC1_FCCA, "GT", "GUATEMALA", YES, YES, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_HONDURAS, NULL1_WORLD, "HN", "HONDURAS", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_HONG_KONG, FCC2_WORLD, "HK", "HONG KONG", YES, YES, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_HUNGARY, ETSI1_WORLD, "HU", "HUNGARY", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_ICELAND, ETSI1_WORLD, "IS", "ICELAND", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_INDIA, APL6_WORLD, "IN", "INDIA", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_INDONESIA, APL1_WORLD, "ID", "INDONESIA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_IRAN, APL1_WORLD, "IR", "IRAN", YES, YES, YES, YES, YES, YES,
+ YES, 7000},
+ {CTRY_IRELAND, ETSI1_WORLD, "IE", "IRELAND", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_ISRAEL, NULL1_WORLD, "IL", "ISRAEL", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_ITALY, ETSI1_WORLD, "IT", "ITALY", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAMAICA, ETSI1_WORLD, "JM", "JAMAICA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+
+ {CTRY_JAPAN, MKK1_MKKA, "JP", "JAPAN", YES, NO, NO, YES, YES, YES,
+ YES, 7000},
+ {CTRY_JAPAN1, MKK1_MKKB, "JP", "JAPAN1", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN2, MKK1_FCCA, "JP", "JAPAN2", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN3, MKK2_MKKA, "JP", "JAPAN3", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN4, MKK1_MKKA1, "JP", "JAPAN4", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN5, MKK1_MKKA2, "JP", "JAPAN5", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN6, MKK1_MKKC, "JP", "JAPAN6", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN7, MKK3_MKKB, "JP", "JAPAN7", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN8, MKK3_MKKA2, "JP", "JAPAN8", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN9, MKK3_MKKC, "JP", "JAPAN9", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN10, MKK4_MKKB, "JP", "JAPAN10", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN11, MKK4_MKKA2, "JP", "JAPAN11", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN12, MKK4_MKKC, "JP", "JAPAN12", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN13, MKK5_MKKB, "JP", "JAPAN13", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN14, MKK5_MKKA2, "JP", "JAPAN14", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN15, MKK5_MKKC, "JP", "JAPAN15", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN16, MKK6_MKKB, "JP", "JAPAN16", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN17, MKK6_MKKA2, "JP", "JAPAN17", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN18, MKK6_MKKC, "JP", "JAPAN18", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN19, MKK7_MKKB, "JP", "JAPAN19", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN20, MKK7_MKKA2, "JP", "JAPAN20", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN21, MKK7_MKKC, "JP", "JAPAN21", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN22, MKK8_MKKB, "JP", "JAPAN22", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN23, MKK8_MKKA2, "JP", "JAPAN23", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN24, MKK8_MKKC, "JP", "JAPAN24", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN25, MKK3_MKKA, "JP", "JAPAN25", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN26, MKK3_MKKA1, "JP", "JAPAN26", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN27, MKK3_FCCA, "JP", "JAPAN27", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN28, MKK4_MKKA1, "JP", "JAPAN28", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN29, MKK4_FCCA, "JP", "JAPAN29", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN30, MKK6_MKKA1, "JP", "JAPAN30", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN31, MKK6_FCCA, "JP", "JAPAN31", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN32, MKK7_MKKA1, "JP", "JAPAN32", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN33, MKK7_FCCA, "JP", "JAPAN33", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN34, MKK9_MKKA, "JP", "JAPAN34", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN35, MKK10_MKKA, "JP", "JAPAN35", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN36, MKK4_MKKA, "JP", "JAPAN36", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN37, MKK9_FCCA, "JP", "JAPAN37", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN38, MKK9_MKKA1, "JP", "JAPAN38", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN39, MKK9_MKKC, "JP", "JAPAN39", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN40, MKK9_MKKA2, "JP", "JAPAN40", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN41, MKK10_FCCA, "JP", "JAPAN41", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN42, MKK10_MKKA1, "JP", "JAPAN42", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN43, MKK10_MKKC, "JP", "JAPAN43", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN44, MKK10_MKKA2, "JP", "JAPAN44", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN45, MKK11_MKKA, "JP", "JAPAN45", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN46, MKK11_FCCA, "JP", "JAPAN46", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN47, MKK11_MKKA1, "JP", "JAPAN47", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN48, MKK11_MKKC, "JP", "JAPAN48", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN49, MKK11_MKKA2, "JP", "JAPAN49", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN50, MKK12_MKKA, "JP", "JAPAN50", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN51, MKK12_FCCA, "JP", "JAPAN51", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN52, MKK12_MKKA1, "JP", "JAPAN52", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN53, MKK12_MKKC, "JP", "JAPAN53", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN54, MKK12_MKKA2, "JP", "JAPAN54", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JAPAN57, MKK13_MKKB, "JP", "JAPAN57", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN58, MKK14_MKKA1, "JP", "JAPAN58", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+ {CTRY_JAPAN59, MKK15_MKKA1, "JP", "JAPAN59", YES, NO, NO, YES, YES,
+ YES, YES, 7000},
+
+ {CTRY_JORDAN, ETSI2_WORLD, "JO", "JORDAN", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_KAZAKHSTAN, NULL1_WORLD, "KZ", "KAZAKHSTAN", YES, NO, YES,
+ YES, YES, NO, NO, 7000},
+ {CTRY_KOREA_NORTH, APL9_WORLD, "KP", "NORTH KOREA", YES, NO, NO,
+ YES, YES, YES, YES, 7000},
+ {CTRY_KOREA_ROC, APL9_WORLD, "KR", "KOREA REPUBLIC", YES, NO, NO,
+ YES, NO, YES, NO, 7000},
+ {CTRY_KOREA_ROC2, APL2_WORLD, "K2", "KOREA REPUBLIC2", YES, NO, NO,
+ YES, NO, YES, NO, 7000},
+ {CTRY_KOREA_ROC3, APL9_WORLD, "K3", "KOREA REPUBLIC3", YES, NO, NO,
+ YES, NO, YES, NO, 7000},
+ {CTRY_KUWAIT, NULL1_WORLD, "KW", "KUWAIT", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_LATVIA, ETSI1_WORLD, "LV", "LATVIA", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_LEBANON, NULL1_WORLD, "LB", "LEBANON", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_LIECHTENSTEIN, ETSI1_WORLD, "LI", "LIECHTENSTEIN", YES, NO,
+ YES, YES, YES, YES, YES, 7000},
+ {CTRY_LITHUANIA, ETSI1_WORLD, "LT", "LITHUANIA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_LUXEMBOURG, ETSI1_WORLD, "LU", "LUXEMBOURG", YES, NO, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_MACAU, FCC2_WORLD, "MO", "MACAU", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_MACEDONIA, NULL1_WORLD, "MK", "MACEDONIA", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_MALAYSIA, APL8_WORLD, "MY", "MALAYSIA", YES, NO, NO, YES, NO,
+ YES, NO, 7000},
+ {CTRY_MALTA, ETSI1_WORLD, "MT", "MALTA", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_MEXICO, FCC1_FCCA, "MX", "MEXICO", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_MONACO, ETSI4_WORLD, "MC", "MONACO", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_MOROCCO, NULL1_WORLD, "MA", "MOROCCO", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_NEPAL, APL1_WORLD, "NP", "NEPAL", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_NETHERLANDS, ETSI1_WORLD, "NL", "NETHERLANDS", YES, NO, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_NETHERLANDS_ANTILLES, ETSI1_WORLD, "AN",
+ "NETHERLANDS-ANTILLES", YES, NO, YES, YES, YES, YES, YES, 7000},
+ {CTRY_NEW_ZEALAND, FCC2_ETSIC, "NZ", "NEW ZEALAND", YES, NO, YES,
+ YES, YES, YES, NO, 7000},
+ {CTRY_NORWAY, ETSI1_WORLD, "NO", "NORWAY", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_OMAN, APL6_WORLD, "OM", "OMAN", YES, NO, YES, YES, YES, YES,
+ NO, 7000},
+ {CTRY_PAKISTAN, NULL1_WORLD, "PK", "PAKISTAN", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_PANAMA, FCC1_FCCA, "PA", "PANAMA", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_PAPUA_NEW_GUINEA, FCC1_WORLD, "PG", "PAPUA NEW GUINEA", YES,
+ YES, YES, YES, YES, YES, YES, 7000},
+ {CTRY_PERU, APL1_WORLD, "PE", "PERU", YES, NO, YES, YES, YES, YES,
+ NO, 7000},
+ {CTRY_PHILIPPINES, APL1_WORLD, "PH", "PHILIPPINES", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_POLAND, ETSI1_WORLD, "PL", "POLAND", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_PORTUGAL, ETSI1_WORLD, "PT", "PORTUGAL", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_PUERTO_RICO, FCC1_FCCA, "PR", "PUERTO RICO", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_QATAR, NULL1_WORLD, "QA", "QATAR", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_ROMANIA, NULL1_WORLD, "RO", "ROMANIA", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_RUSSIA, NULL1_WORLD, "RU", "RUSSIA", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_SAUDI_ARABIA, NULL1_WORLD, "SA", "SAUDI ARABIA", YES, NO,
+ YES, YES, YES, NO, NO, 7000},
+ {CTRY_SERBIA_MONTENEGRO, ETSI1_WORLD, "CS", "SERBIA & MONTENEGRO",
+ YES, NO, YES, YES, YES, YES, YES, 7000},
+ {CTRY_SINGAPORE, APL6_WORLD, "SG", "SINGAPORE", YES, YES, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_SLOVAKIA, ETSI1_WORLD, "SK", "SLOVAK REPUBLIC", YES, NO, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_SLOVENIA, ETSI1_WORLD, "SI", "SLOVENIA", YES, NO, YES, YES,
+ YES, YES, YES, 7000},
+ {CTRY_SOUTH_AFRICA, FCC3_WORLD, "ZA", "SOUTH AFRICA", YES, NO, YES,
+ YES, YES, YES, NO, 7000},
+ {CTRY_SPAIN, ETSI1_WORLD, "ES", "SPAIN", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_SRI_LANKA, FCC3_WORLD, "LK", "SRI LANKA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_SWEDEN, ETSI1_WORLD, "SE", "SWEDEN", YES, NO, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_SWITZERLAND, ETSI1_WORLD, "CH", "SWITZERLAND", YES, NO, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_SYRIA, NULL1_WORLD, "SY", "SYRIA", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_TAIWAN, APL3_FCCA, "TW", "TAIWAN", YES, YES, YES, YES, YES,
+ YES, YES, 7000},
+ {CTRY_THAILAND, NULL1_WORLD, "TH", "THAILAND", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_TRINIDAD_Y_TOBAGO, ETSI4_WORLD, "TT", "TRINIDAD & TOBAGO",
+ YES, NO, YES, YES, YES, YES, NO, 7000},
+ {CTRY_TUNISIA, ETSI3_WORLD, "TN", "TUNISIA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_TURKEY, ETSI3_WORLD, "TR", "TURKEY", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_UKRAINE, NULL1_WORLD, "UA", "UKRAINE", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_UAE, NULL1_WORLD, "AE", "UNITED ARAB EMIRATES", YES, NO, YES,
+ YES, YES, NO, NO, 7000},
+ {CTRY_UNITED_KINGDOM, ETSI1_WORLD, "GB", "UNITED KINGDOM", YES, NO,
+ YES, YES, YES, YES, YES, 7000},
+ {CTRY_UNITED_STATES, FCC3_FCCA, "US", "UNITED STATES", YES, YES,
+ YES, YES, YES, YES, YES, 5825},
+ {CTRY_UNITED_STATES_FCC49, FCC4_FCCA, "PS",
+ "UNITED STATES (PUBLIC SAFETY)", YES, YES, YES, YES, YES, YES,
+ YES, 7000},
+ {CTRY_URUGUAY, APL2_WORLD, "UY", "URUGUAY", YES, NO, YES, YES, YES,
+ YES, NO, 7000},
+ {CTRY_UZBEKISTAN, FCC3_FCCA, "UZ", "UZBEKISTAN", YES, YES, YES,
+ YES, YES, YES, YES, 7000},
+ {CTRY_VENEZUELA, APL2_ETSIC, "VE", "VENEZUELA", YES, NO, YES, YES,
+ YES, YES, NO, 7000},
+ {CTRY_VIET_NAM, NULL1_WORLD, "VN", "VIET NAM", YES, NO, YES, YES,
+ YES, NO, NO, 7000},
+ {CTRY_YEMEN, NULL1_WORLD, "YE", "YEMEN", YES, NO, YES, YES, YES,
+ NO, NO, 7000},
+ {CTRY_ZIMBABWE, NULL1_WORLD, "ZW", "ZIMBABWE", YES, NO, YES, YES,
+ YES, NO, NO, 7000}
+};
+
+enum {
+ NO_DFS = 0x0000000000000000ULL,
+ DFS_FCC3 = 0x0000000000000001ULL,
+ DFS_ETSI = 0x0000000000000002ULL,
+ DFS_MKK4 = 0x0000000000000004ULL,
+};
+
+enum {
+ F1_4915_4925,
+ F1_4935_4945,
+ F1_4920_4980,
+ F1_4942_4987,
+ F1_4945_4985,
+ F1_4950_4980,
+ F1_5035_5040,
+ F1_5040_5080,
+ F1_5055_5055,
+
+ F1_5120_5240,
+
+ F1_5170_5230,
+ F2_5170_5230,
+
+ F1_5180_5240,
+ F2_5180_5240,
+ F3_5180_5240,
+ F4_5180_5240,
+ F5_5180_5240,
+ F6_5180_5240,
+ F7_5180_5240,
+ F8_5180_5240,
+
+ F1_5180_5320,
+
+ F1_5240_5280,
+
+ F1_5260_5280,
+
+ F1_5260_5320,
+ F2_5260_5320,
+ F3_5260_5320,
+ F4_5260_5320,
+ F5_5260_5320,
+ F6_5260_5320,
+
+ F1_5260_5700,
+
+ F1_5280_5320,
+
+ F1_5500_5580,
+
+ F1_5500_5620,
+
+ F1_5500_5700,
+ F2_5500_5700,
+ F3_5500_5700,
+ F4_5500_5700,
+ F5_5500_5700,
+
+ F1_5660_5700,
+
+ F1_5745_5805,
+ F2_5745_5805,
+ F3_5745_5805,
+
+ F1_5745_5825,
+ F2_5745_5825,
+ F3_5745_5825,
+ F4_5745_5825,
+ F5_5745_5825,
+ F6_5745_5825,
+
+ W1_4920_4980,
+ W1_5040_5080,
+ W1_5170_5230,
+ W1_5180_5240,
+ W1_5260_5320,
+ W1_5745_5825,
+ W1_5500_5700,
+ A_DEMO_ALL_CHANNELS
+};
+
+static struct RegDmnFreqBand regDmn5GhzFreq[] = {
+ {4915, 4925, 23, 0, 10, 5, NO_DFS, PSCAN_MKK2, 16},
+ {4935, 4945, 23, 0, 10, 5, NO_DFS, PSCAN_MKK2, 16},
+ {4920, 4980, 23, 0, 20, 20, NO_DFS, PSCAN_MKK2, 7},
+ {4942, 4987, 27, 6, 5, 5, NO_DFS, PSCAN_FCC, 0},
+ {4945, 4985, 30, 6, 10, 5, NO_DFS, PSCAN_FCC, 0},
+ {4950, 4980, 33, 6, 20, 5, NO_DFS, PSCAN_FCC, 0},
+ {5035, 5040, 23, 0, 10, 5, NO_DFS, PSCAN_MKK2, 12},
+ {5040, 5080, 23, 0, 20, 20, NO_DFS, PSCAN_MKK2, 2},
+ {5055, 5055, 23, 0, 10, 5, NO_DFS, PSCAN_MKK2, 12},
+
+ {5120, 5240, 5, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+
+ {5170, 5230, 23, 0, 20, 20, NO_DFS, PSCAN_MKK1 | PSCAN_MKK2, 1},
+ {5170, 5230, 20, 0, 20, 20, NO_DFS, PSCAN_MKK1 | PSCAN_MKK2, 1},
+
+ {5180, 5240, 15, 0, 20, 20, NO_DFS, PSCAN_FCC | PSCAN_ETSI, 0},
+ {5180, 5240, 17, 6, 20, 20, NO_DFS, NO_PSCAN, 1},
+ {5180, 5240, 18, 0, 20, 20, NO_DFS, PSCAN_FCC | PSCAN_ETSI, 0},
+ {5180, 5240, 20, 0, 20, 20, NO_DFS, PSCAN_FCC | PSCAN_ETSI, 0},
+ {5180, 5240, 23, 0, 20, 20, NO_DFS, PSCAN_FCC | PSCAN_ETSI, 0},
+ {5180, 5240, 23, 6, 20, 20, NO_DFS, PSCAN_FCC, 0},
+ {5180, 5240, 20, 0, 20, 20, NO_DFS, PSCAN_MKK1 | PSCAN_MKK3, 0},
+ {5180, 5240, 23, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+
+ {5180, 5320, 20, 6, 20, 20, NO_DFS, PSCAN_ETSI, 0},
+
+ {5240, 5280, 23, 0, 20, 20, DFS_FCC3, PSCAN_FCC | PSCAN_ETSI, 0},
+
+ {5260, 5280, 23, 0, 20, 20, DFS_FCC3 | DFS_ETSI,
+ PSCAN_FCC | PSCAN_ETSI, 0},
+
+ {5260, 5320, 18, 0, 20, 20, DFS_FCC3 | DFS_ETSI,
+ PSCAN_FCC | PSCAN_ETSI, 0},
+
+ {5260, 5320, 20, 0, 20, 20, DFS_FCC3 | DFS_ETSI | DFS_MKK4,
+ PSCAN_FCC | PSCAN_ETSI | PSCAN_MKK3, 0},
+
+
+ {5260, 5320, 20, 6, 20, 20, DFS_FCC3 | DFS_ETSI,
+ PSCAN_FCC | PSCAN_ETSI, 2},
+ {5260, 5320, 23, 6, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_FCC, 2},
+ {5260, 5320, 23, 6, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_FCC, 0},
+ {5260, 5320, 30, 0, 20, 20, NO_DFS, NO_PSCAN, 0},
+
+ {5260, 5700, 5, 6, 20, 20, DFS_FCC3 | DFS_ETSI, NO_PSCAN, 0},
+
+ {5280, 5320, 17, 6, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_FCC, 0},
+
+ {5500, 5580, 23, 6, 20, 20, DFS_FCC3, PSCAN_FCC, 0},
+
+ {5500, 5620, 30, 6, 20, 20, DFS_ETSI, PSCAN_ETSI, 0},
+
+ {5500, 5700, 20, 6, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_FCC, 4},
+ {5500, 5700, 27, 0, 20, 20, DFS_FCC3 | DFS_ETSI,
+ PSCAN_FCC | PSCAN_ETSI, 0},
+ {5500, 5700, 30, 0, 20, 20, DFS_FCC3 | DFS_ETSI,
+ PSCAN_FCC | PSCAN_ETSI, 0},
+ {5500, 5700, 23, 0, 20, 20, DFS_FCC3 | DFS_ETSI | DFS_MKK4,
+ PSCAN_MKK3 | PSCAN_FCC, 0},
+ {5500, 5700, 30, 6, 20, 20, DFS_ETSI, PSCAN_ETSI, 0},
+
+ {5660, 5700, 23, 6, 20, 20, DFS_FCC3, PSCAN_FCC, 0},
+
+ {5745, 5805, 23, 0, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5805, 30, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5805, 30, 6, 20, 20, NO_DFS, PSCAN_ETSI, 0},
+ {5745, 5825, 5, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5825, 17, 0, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5825, 20, 0, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5825, 30, 0, 20, 20, NO_DFS, NO_PSCAN, 0},
+ {5745, 5825, 30, 6, 20, 20, NO_DFS, NO_PSCAN, 3},
+ {5745, 5825, 30, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+
+
+ {4920, 4980, 30, 0, 20, 20, NO_DFS, PSCAN_WWR, 0},
+ {5040, 5080, 30, 0, 20, 20, NO_DFS, PSCAN_WWR, 0},
+ {5170, 5230, 30, 0, 20, 20, NO_DFS, PSCAN_WWR, 0},
+ {5180, 5240, 30, 0, 20, 20, NO_DFS, PSCAN_WWR, 0},
+ {5260, 5320, 30, 0, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, 0},
+ {5745, 5825, 30, 0, 20, 20, NO_DFS, PSCAN_WWR, 0},
+ {5500, 5700, 30, 0, 20, 20, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, 0},
+ {4920, 6100, 30, 6, 20, 20, NO_DFS, NO_PSCAN, 0},
+};
+
+enum {
+ T1_5130_5650,
+ T1_5150_5670,
+
+ T1_5200_5200,
+ T2_5200_5200,
+ T3_5200_5200,
+ T4_5200_5200,
+ T5_5200_5200,
+ T6_5200_5200,
+ T7_5200_5200,
+ T8_5200_5200,
+
+ T1_5200_5280,
+ T2_5200_5280,
+ T3_5200_5280,
+ T4_5200_5280,
+ T5_5200_5280,
+ T6_5200_5280,
+
+ T1_5200_5240,
+ T1_5210_5210,
+ T2_5210_5210,
+ T3_5210_5210,
+ T4_5210_5210,
+ T5_5210_5210,
+ T6_5210_5210,
+ T7_5210_5210,
+ T8_5210_5210,
+ T9_5210_5210,
+ T10_5210_5210,
+ T1_5240_5240,
+
+ T1_5210_5250,
+ T1_5210_5290,
+ T2_5210_5290,
+ T3_5210_5290,
+
+ T1_5280_5280,
+ T2_5280_5280,
+ T1_5290_5290,
+ T2_5290_5290,
+ T3_5290_5290,
+ T1_5250_5290,
+ T2_5250_5290,
+ T3_5250_5290,
+ T4_5250_5290,
+
+ T1_5540_5660,
+ T2_5540_5660,
+ T3_5540_5660,
+ T1_5760_5800,
+ T2_5760_5800,
+ T3_5760_5800,
+ T4_5760_5800,
+ T5_5760_5800,
+ T6_5760_5800,
+ T7_5760_5800,
+
+ T1_5765_5805,
+ T2_5765_5805,
+ T3_5765_5805,
+ T4_5765_5805,
+ T5_5765_5805,
+ T6_5765_5805,
+ T7_5765_5805,
+ T8_5765_5805,
+ T9_5765_5805,
+
+ WT1_5210_5250,
+ WT1_5290_5290,
+ WT1_5540_5660,
+ WT1_5760_5800,
+};
+
+enum {
+ F1_2312_2372,
+ F2_2312_2372,
+
+ F1_2412_2472,
+ F2_2412_2472,
+ F3_2412_2472,
+
+ F1_2412_2462,
+ F2_2412_2462,
+
+ F1_2432_2442,
+
+ F1_2457_2472,
+
+ F1_2467_2472,
+
+ F1_2484_2484,
+ F2_2484_2484,
+
+ F1_2512_2732,
+
+ W1_2312_2372,
+ W1_2412_2412,
+ W1_2417_2432,
+ W1_2437_2442,
+ W1_2447_2457,
+ W1_2462_2462,
+ W1_2467_2467,
+ W2_2467_2467,
+ W1_2472_2472,
+ W2_2472_2472,
+ W1_2484_2484,
+ W2_2484_2484,
+};
+
+static struct RegDmnFreqBand regDmn2GhzFreq[] = {
+ {2312, 2372, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2312, 2372, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2412, 2472, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA, 0},
+ {2412, 2472, 30, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2412, 2462, 27, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2462, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA, 0},
+
+ {2432, 2442, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2457, 2472, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2467, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA2 | PSCAN_MKKA, 0},
+
+ {2484, 2484, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2484, 2484, 20, 0, 20, 5, NO_DFS,
+ PSCAN_MKKA | PSCAN_MKKA1 | PSCAN_MKKA2, 0},
+
+ {2512, 2732, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2312, 2372, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2412, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2417, 2432, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2437, 2442, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2447, 2457, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2462, 2462, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2467, 2467, 20, 0, 20, 5, NO_DFS, PSCAN_WWR | IS_ECM_CHAN, 0},
+ {2467, 2467, 20, 0, 20, 5, NO_DFS, NO_PSCAN | IS_ECM_CHAN, 0},
+ {2472, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_WWR | IS_ECM_CHAN, 0},
+ {2472, 2472, 20, 0, 20, 5, NO_DFS, NO_PSCAN | IS_ECM_CHAN, 0},
+ {2484, 2484, 20, 0, 20, 5, NO_DFS, PSCAN_WWR | IS_ECM_CHAN, 0},
+ {2484, 2484, 20, 0, 20, 5, NO_DFS, NO_PSCAN | IS_ECM_CHAN, 0},
+};
+
+enum {
+ G1_2312_2372,
+ G2_2312_2372,
+
+ G1_2412_2472,
+ G2_2412_2472,
+ G3_2412_2472,
+
+ G1_2412_2462,
+ G2_2412_2462,
+
+ G1_2432_2442,
+
+ G1_2457_2472,
+
+ G1_2512_2732,
+
+ G1_2467_2472,
+
+ WG1_2312_2372,
+ WG1_2412_2462,
+ WG1_2467_2472,
+ WG2_2467_2472,
+ G_DEMO_ALL_CHANNELS
+};
+
+static struct RegDmnFreqBand regDmn2Ghz11gFreq[] = {
+ {2312, 2372, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2312, 2372, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2412, 2472, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA_G, 0},
+ {2412, 2472, 30, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2412, 2462, 27, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2462, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA_G, 0},
+
+ {2432, 2442, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2457, 2472, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2512, 2732, 5, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+
+ {2467, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_MKKA2 | PSCAN_MKKA, 0},
+
+ {2312, 2372, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2412, 2462, 20, 0, 20, 5, NO_DFS, NO_PSCAN, 0},
+ {2467, 2472, 20, 0, 20, 5, NO_DFS, PSCAN_WWR | IS_ECM_CHAN, 0},
+ {2467, 2472, 20, 0, 20, 5, NO_DFS, NO_PSCAN | IS_ECM_CHAN, 0},
+ {2312, 2732, 27, 6, 20, 5, NO_DFS, NO_PSCAN, 0},
+};
+
+enum {
+ T1_2312_2372,
+ T1_2437_2437,
+ T2_2437_2437,
+ T3_2437_2437,
+ T1_2512_2732
+};
+
+static struct regDomain regDomains[] = {
+
+ {DEBUG_REG_DMN, FCC, DFS_FCC3, NO_PSCAN, NO_REQ,
+ BM(A_DEMO_ALL_CHANNELS, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5130_5650, T1_5150_5670, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5200_5240, T1_5280_5280, T1_5540_5660, T1_5765_5805, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(F1_2312_2372, F1_2412_2472, F1_2484_2484, F1_2512_2732, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(G_DEMO_ALL_CHANNELS, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_2312_2372, T1_2437_2437, T1_2512_2732, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1)},
+
+ {APL1, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F4_5745_5825, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL2, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F1_5745_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL3, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F1_5280_5320, F2_5745_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5290_5290, T1_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL4, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F4_5180_5240, F3_5745_5825, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5210_5210, T3_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5200_5200, T3_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL5, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F2_5745_5825, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T4_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T4_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL6, ETSI, DFS_ETSI, PSCAN_FCC_T | PSCAN_FCC, NO_REQ,
+ BM(F4_5180_5240, F2_5260_5320, F3_5745_5825, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T2_5210_5210, T1_5250_5290, T1_5760_5800, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T1_5200_5280, T5_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL7, ETSI, DFS_ETSI, PSCAN_ETSI, NO_REQ,
+ BM(F1_5280_5320, F5_5500_5700, F3_5745_5805, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T3_5290_5290, T5_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5540_5660, T6_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL8, ETSI, NO_DFS, NO_PSCAN,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F6_5260_5320, F4_5745_5825, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T2_5290_5290, T2_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5280_5280, T1_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL9, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5180_5320, F1_5500_5620, F3_5745_5805, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T3_5290_5290, T5_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5540_5660, T6_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {APL10, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5180_5320, F5_5500_5700, F3_5745_5805, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T3_5290_5290, T5_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5540_5660, T6_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI1, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F4_5180_5240, F2_5260_5320, F2_5500_5700, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T1_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_5200_5280, T2_5540_5660, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI2, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F3_5180_5240, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI3, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F4_5180_5240, F2_5260_5320, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T1_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI4, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F3_5180_5240, F1_5260_5320, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T2_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI5, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5180_5240, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T4_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {ETSI6, ETSI, DFS_ETSI, PSCAN_ETSI,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F5_5180_5240, F1_5260_5280, F3_5500_5700, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T1_5210_5250, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T4_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC1, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F2_5180_5240, F4_5260_5320, F5_5745_5825, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T6_5210_5210, T2_5250_5290, T6_5760_5800, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T1_5200_5240, T2_5280_5280, T7_5765_5805, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC2, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F6_5180_5240, F5_5260_5320, F6_5745_5825, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T7_5210_5210, T3_5250_5290, T2_5760_5800, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T7_5200_5200, T1_5240_5240, T2_5280_5280, T1_5765_5805, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC3, FCC, DFS_FCC3, PSCAN_FCC | PSCAN_FCC_T, NO_REQ,
+ BM(F2_5180_5240, F3_5260_5320, F1_5500_5700, F5_5745_5825, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(T6_5210_5210, T2_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T4_5200_5200, T8_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC4, FCC, DFS_FCC3, PSCAN_FCC | PSCAN_FCC_T, NO_REQ,
+ BM(F1_4942_4987, F1_4945_4985, F1_4950_4980, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T8_5210_5210, T4_5250_5290, T7_5760_5800, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T1_5200_5240, T1_5280_5280, T9_5765_5805, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC5, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BM(F2_5180_5240, F6_5745_5825, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T6_5210_5210, T2_5760_5800, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T8_5200_5200, T7_5765_5805, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {FCC6, FCC, DFS_FCC3, PSCAN_FCC, NO_REQ,
+ BM(F8_5180_5240, F5_5260_5320, F1_5500_5580, F1_5660_5700,
+ F6_5745_5825, -1, -1, -1, -1, -1, -1, -1),
+ BM(T7_5210_5210, T3_5250_5290, T2_5760_5800, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T7_5200_5200, T1_5240_5240, T2_5280_5280, T1_5765_5805, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {MKK1, MKK, NO_DFS, PSCAN_MKK1, DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5170_5230, F4_5180_5240, F2_5260_5320, F4_5500_5700, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(T7_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T5_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+ {MKK2, MKK, NO_DFS, PSCAN_MKK2, DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5055_5055, F1_5040_5080, F1_5170_5230, F4_5180_5240,
+ F2_5260_5320, F4_5500_5700, -1, -1),
+ BM(T7_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T5_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK3, MKK, NO_DFS, PSCAN_MKK3, DISALLOW_ADHOC_11A_TURB,
+ BM(F4_5180_5240, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T9_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK4, MKK, DFS_MKK4, PSCAN_MKK3, DISALLOW_ADHOC_11A_TURB,
+ BM(F4_5180_5240, F2_5260_5320, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T10_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T6_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK5, MKK, DFS_MKK4, PSCAN_MKK3, DISALLOW_ADHOC_11A_TURB,
+ BM(F4_5180_5240, F2_5260_5320, F4_5500_5700, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T5_5200_5280, T3_5540_5660, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK6, MKK, NO_DFS, PSCAN_MKK1, DISALLOW_ADHOC_11A_TURB,
+ BM(F2_5170_5230, F4_5180_5240, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T3_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T6_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK7, MKK, DFS_MKK4, PSCAN_MKK1 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5170_5230, F4_5180_5240, F2_5260_5320, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T5_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK8, MKK, DFS_MKK4, PSCAN_MKK1 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5170_5230, F4_5180_5240, F2_5260_5320, F4_5500_5700, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T5_5200_5280, T3_5540_5660, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK9, MKK, NO_DFS, PSCAN_MKK2 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5055_5055, F1_5040_5080, F4_5180_5240, -1, -1, -1, -1, -1),
+ BM(T9_5210_5210, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5200_5200, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK10, MKK, DFS_MKK4, PSCAN_MKK2 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5055_5055, F1_5040_5080, F4_5180_5240, F2_5260_5320, -1, -1,
+ -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK11, MKK, DFS_MKK4, PSCAN_MKK3, DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5055_5055, F1_5040_5080, F4_5180_5240, F2_5260_5320,
+ F4_5500_5700, -1, -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK12, MKK, DFS_MKK4, PSCAN_MKK1 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5055_5055, F1_5040_5080, F1_5170_5230, F4_5180_5240,
+ F2_5260_5320, F4_5500_5700, -1, -1),
+ BM(T3_5210_5290, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T1_5200_5280, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK13, MKK, DFS_MKK4, PSCAN_MKK1 | PSCAN_MKK3,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BM(F1_5170_5230, F7_5180_5240, F2_5260_5320, F4_5500_5700, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK14, MKK, DFS_MKK4, PSCAN_MKK1, DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5040_5080, F1_5055_5055, F1_5170_5230, F4_5180_5240, -1, -1,
+ -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {MKK15, MKK, DFS_MKK4, PSCAN_MKK1, DISALLOW_ADHOC_11A_TURB,
+ BM(F1_4915_4925, F1_4935_4945, F1_4920_4980, F1_5035_5040,
+ F1_5040_5080, F1_5055_5055, F1_5170_5230, F4_5180_5240,
+ F2_5260_5320, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO},
+
+
+ {APLD, NO_CTL, NO_DFS, NO_PSCAN, NO_REQ,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F2_2312_2372, F2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(G2_2312_2372, G2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BMZERO},
+
+ {ETSIA, NO_CTL, NO_DFS, PSCAN_ETSIA,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F1_2457_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G1_2457_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {ETSIB, ETSI, NO_DFS, PSCAN_ETSIB,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F1_2432_2442, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G1_2432_2442, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {ETSIC, ETSI, NO_DFS, PSCAN_ETSIC,
+ DISALLOW_ADHOC_11A | DISALLOW_ADHOC_11A_TURB,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F3_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G3_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {FCCA, FCC, NO_DFS, NO_PSCAN, NO_REQ,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F1_2412_2462, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G1_2412_2462, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {MKKA, MKK, NO_DFS,
+ PSCAN_MKKA | PSCAN_MKKA_G | PSCAN_MKKA1 | PSCAN_MKKA1_G |
+ PSCAN_MKKA2 | PSCAN_MKKA2_G, DISALLOW_ADHOC_11A_TURB,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F2_2412_2462, F1_2467_2472, F2_2484_2484, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(G2_2412_2462, G1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {MKKC, MKK, NO_DFS, NO_PSCAN, NO_REQ,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WORLD, ETSI, NO_DFS, NO_PSCAN, NO_REQ,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BM(F2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(G2_2412_2472, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T2_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR0_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_PER_11D,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, W1_2484_2484, -1, -1,
+ -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR01_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR,
+ ADHOC_PER_11D,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2417_2432,
+ W1_2447_2457, -1, -1, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR02_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR,
+ ADHOC_PER_11D,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {EU1_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_PER_11D,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W2_2472_2472,
+ W1_2417_2432, W1_2447_2457, W2_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG2_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR1_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, W1_2484_2484, -1, -1,
+ -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR2_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825,
+ W1_5500_5700, -1, -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, W1_2484_2484, -1, -1,
+ -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR3_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_PER_11D,
+ BM(W1_5260_5320, W1_5180_5240, W1_5170_5230, W1_5745_5825, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG2_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR4_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5745_5825, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2417_2432,
+ W1_2447_2457, -1, -1, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR5_ETSIC, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5745_5825, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WOR9_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5745_5825, W1_5500_5700, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BM(WT1_5210_5250, WT1_5290_5290, WT1_5760_5800, -1, -1, -1, -1,
+ -1, -1, -1, -1, -1),
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2417_2432,
+ W1_2447_2457, -1, -1, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WORA_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5745_5825, W1_5500_5700, -1, -1,
+ -1, -1, -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {WORB_WORLD, NO_CTL, DFS_FCC3 | DFS_ETSI, PSCAN_WWR, ADHOC_NO_11A,
+ BM(W1_5260_5320, W1_5180_5240, W1_5500_5700, -1, -1, -1, -1, -1,
+ -1, -1, -1, -1),
+ BMZERO,
+ BMZERO,
+ BM(W1_2412_2412, W1_2437_2442, W1_2462_2462, W1_2472_2472,
+ W1_2417_2432, W1_2447_2457, W1_2467_2467, -1, -1, -1, -1, -1),
+ BM(WG1_2412_2462, WG1_2467_2472, -1, -1, -1, -1, -1, -1, -1, -1,
+ -1, -1),
+ BM(T3_2437_2437, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1)},
+
+ {NULL1, NO_CTL, NO_DFS, NO_PSCAN, NO_REQ,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO,
+ BMZERO}
+};
+
+static const struct cmode modes[] = {
+ {ATH9K_MODE_11A, CHANNEL_A},
+ {ATH9K_MODE_11B, CHANNEL_B},
+ {ATH9K_MODE_11G, CHANNEL_G},
+ {ATH9K_MODE_11NG_HT20, CHANNEL_G_HT20},
+ {ATH9K_MODE_11NG_HT40PLUS, CHANNEL_G_HT40PLUS},
+ {ATH9K_MODE_11NG_HT40MINUS, CHANNEL_G_HT40MINUS},
+ {ATH9K_MODE_11NA_HT20, CHANNEL_A_HT20},
+ {ATH9K_MODE_11NA_HT40PLUS, CHANNEL_A_HT40PLUS},
+ {ATH9K_MODE_11NA_HT40MINUS, CHANNEL_A_HT40MINUS},
+};
+
+static struct japan_bandcheck j_bandcheck[] = {
+ {F1_5170_5230, AR_EEPROM_EEREGCAP_EN_KK_U1_ODD},
+ {F4_5180_5240, AR_EEPROM_EEREGCAP_EN_KK_U1_EVEN},
+ {F2_5260_5320, AR_EEPROM_EEREGCAP_EN_KK_U2},
+ {F4_5500_5700, AR_EEPROM_EEREGCAP_EN_KK_MIDBAND}
+};
+
+
+#endif
--- /dev/null
+/*
+ * Copyright (c) 2008 Atheros Communications Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+/*
+ * Implementation of transmit path.
+ */
+
+#include "core.h"
+
+#define BITS_PER_BYTE 8
+#define OFDM_PLCP_BITS 22
+#define HT_RC_2_MCS(_rc) ((_rc) & 0x0f)
+#define HT_RC_2_STREAMS(_rc) ((((_rc) & 0x78) >> 3) + 1)
+#define L_STF 8
+#define L_LTF 8
+#define L_SIG 4
+#define HT_SIG 8
+#define HT_STF 4
+#define HT_LTF(_ns) (4 * (_ns))
+#define SYMBOL_TIME(_ns) ((_ns) << 2) /* ns * 4 us */
+#define SYMBOL_TIME_HALFGI(_ns) (((_ns) * 18 + 4) / 5) /* ns * 3.6 us */
+#define NUM_SYMBOLS_PER_USEC(_usec) (_usec >> 2)
+#define NUM_SYMBOLS_PER_USEC_HALFGI(_usec) (((_usec*5)-4)/18)
+
+#define OFDM_SIFS_TIME 16
+
+static u32 bits_per_symbol[][2] = {
+ /* 20MHz 40MHz */
+ { 26, 54 }, /* 0: BPSK */
+ { 52, 108 }, /* 1: QPSK 1/2 */
+ { 78, 162 }, /* 2: QPSK 3/4 */
+ { 104, 216 }, /* 3: 16-QAM 1/2 */
+ { 156, 324 }, /* 4: 16-QAM 3/4 */
+ { 208, 432 }, /* 5: 64-QAM 2/3 */
+ { 234, 486 }, /* 6: 64-QAM 3/4 */
+ { 260, 540 }, /* 7: 64-QAM 5/6 */
+ { 52, 108 }, /* 8: BPSK */
+ { 104, 216 }, /* 9: QPSK 1/2 */
+ { 156, 324 }, /* 10: QPSK 3/4 */
+ { 208, 432 }, /* 11: 16-QAM 1/2 */
+ { 312, 648 }, /* 12: 16-QAM 3/4 */
+ { 416, 864 }, /* 13: 64-QAM 2/3 */
+ { 468, 972 }, /* 14: 64-QAM 3/4 */
+ { 520, 1080 }, /* 15: 64-QAM 5/6 */
+};
+
+#define IS_HT_RATE(_rate) ((_rate) & 0x80)
+
+/*
+ * Insert a chain of ath_buf (descriptors) on a multicast txq
+ * but do NOT start tx DMA on this queue.
+ * NB: must be called with txq lock held
+ */
+
+static void ath_tx_mcastqaddbuf(struct ath_softc *sc,
+ struct ath_txq *txq,
+ struct list_head *head)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf;
+
+ if (list_empty(head))
+ return;
+
+ /*
+ * Insert the frame on the outbound list and
+ * pass it on to the hardware.
+ */
+ bf = list_first_entry(head, struct ath_buf, list);
+
+ /*
+ * The CAB queue is started from the SWBA handler since
+ * frames only go out on DTIM and to avoid possible races.
+ */
+ ath9k_hw_set_interrupts(ah, 0);
+
+ /*
+ * If there is anything in the mcastq, we want to set
+ * the "more data" bit in the last item in the queue to
+ * indicate that there is "more data". It makes sense to add
+ * it here since you are *always* going to have
+ * more data when adding to this queue, no matter where
+ * you call from.
+ */
+
+ if (txq->axq_depth) {
+ struct ath_buf *lbf;
+ struct ieee80211_hdr *hdr;
+
+ /*
+ * Add the "more data flag" to the last frame
+ */
+
+ lbf = list_entry(txq->axq_q.prev, struct ath_buf, list);
+ hdr = (struct ieee80211_hdr *)
+ ((struct sk_buff *)(lbf->bf_mpdu))->data;
+ hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_MOREDATA);
+ }
+
+ /*
+ * Now, concat the frame onto the queue
+ */
+ list_splice_tail_init(head, &txq->axq_q);
+ txq->axq_depth++;
+ txq->axq_totalqueued++;
+ txq->axq_linkbuf = list_entry(txq->axq_q.prev, struct ath_buf, list);
+
+ DPRINTF(sc, ATH_DBG_QUEUE,
+ "%s: txq depth = %d\n", __func__, txq->axq_depth);
+ if (txq->axq_link != NULL) {
+ *txq->axq_link = bf->bf_daddr;
+ DPRINTF(sc, ATH_DBG_XMIT,
+ "%s: link[%u](%p)=%llx (%p)\n",
+ __func__,
+ txq->axq_qnum, txq->axq_link,
+ ito64(bf->bf_daddr), bf->bf_desc);
+ }
+ txq->axq_link = &(bf->bf_lastbf->bf_desc->ds_link);
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+}
+
+/*
+ * Insert a chain of ath_buf (descriptors) on a txq and
+ * assume the descriptors are already chained together by caller.
+ * NB: must be called with txq lock held
+ */
+
+static void ath_tx_txqaddbuf(struct ath_softc *sc,
+ struct ath_txq *txq, struct list_head *head)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf;
+ /*
+ * Insert the frame on the outbound list and
+ * pass it on to the hardware.
+ */
+
+ if (list_empty(head))
+ return;
+
+ bf = list_first_entry(head, struct ath_buf, list);
+
+ list_splice_tail_init(head, &txq->axq_q);
+ txq->axq_depth++;
+ txq->axq_totalqueued++;
+ txq->axq_linkbuf = list_entry(txq->axq_q.prev, struct ath_buf, list);
+
+ DPRINTF(sc, ATH_DBG_QUEUE,
+ "%s: txq depth = %d\n", __func__, txq->axq_depth);
+
+ if (txq->axq_link == NULL) {
+ ath9k_hw_puttxbuf(ah, txq->axq_qnum, bf->bf_daddr);
+ DPRINTF(sc, ATH_DBG_XMIT,
+ "%s: TXDP[%u] = %llx (%p)\n",
+ __func__, txq->axq_qnum,
+ ito64(bf->bf_daddr), bf->bf_desc);
+ } else {
+ *txq->axq_link = bf->bf_daddr;
+ DPRINTF(sc, ATH_DBG_XMIT, "%s: link[%u] (%p)=%llx (%p)\n",
+ __func__,
+ txq->axq_qnum, txq->axq_link,
+ ito64(bf->bf_daddr), bf->bf_desc);
+ }
+ txq->axq_link = &(bf->bf_lastbf->bf_desc->ds_link);
+ ath9k_hw_txstart(ah, txq->axq_qnum);
+}
+
+/* Get transmit rate index using rate in Kbps */
+
+static int ath_tx_findindex(const struct ath9k_rate_table *rt, int rate)
+{
+ int i;
+ int ndx = 0;
+
+ for (i = 0; i < rt->rateCount; i++) {
+ if (rt->info[i].rateKbps == rate) {
+ ndx = i;
+ break;
+ }
+ }
+
+ return ndx;
+}
+
+/* Check if it's okay to send out aggregates */
+
+static int ath_aggr_query(struct ath_softc *sc,
+ struct ath_node *an, u8 tidno)
+{
+ struct ath_atx_tid *tid;
+ tid = ATH_AN_2_TID(an, tidno);
+
+ if (tid->addba_exchangecomplete || tid->addba_exchangeinprogress)
+ return 1;
+ else
+ return 0;
+}
+
+static enum ath9k_pkt_type get_hal_packet_type(struct ieee80211_hdr *hdr)
+{
+ enum ath9k_pkt_type htype;
+ __le16 fc;
+
+ fc = hdr->frame_control;
+
+ /* Calculate Atheros packet type from IEEE80211 packet header */
+
+ if (ieee80211_is_beacon(fc))
+ htype = ATH9K_PKT_TYPE_BEACON;
+ else if (ieee80211_is_probe_resp(fc))
+ htype = ATH9K_PKT_TYPE_PROBE_RESP;
+ else if (ieee80211_is_atim(fc))
+ htype = ATH9K_PKT_TYPE_ATIM;
+ else if (ieee80211_is_pspoll(fc))
+ htype = ATH9K_PKT_TYPE_PSPOLL;
+ else
+ htype = ATH9K_PKT_TYPE_NORMAL;
+
+ return htype;
+}
+
+static void fill_min_rates(struct sk_buff *skb, struct ath_tx_control *txctl)
+{
+ struct ieee80211_hdr *hdr;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ struct ath_tx_info_priv *tx_info_priv;
+ __le16 fc;
+
+ hdr = (struct ieee80211_hdr *)skb->data;
+ fc = hdr->frame_control;
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+
+ if (ieee80211_is_mgmt(fc) || ieee80211_is_ctl(fc)) {
+ txctl->use_minrate = 1;
+ txctl->min_rate = tx_info_priv->min_rate;
+ } else if (ieee80211_is_data(fc)) {
+ if (ieee80211_is_nullfunc(fc) ||
+ /* Port Access Entity (IEEE 802.1X) */
+ (skb->protocol == cpu_to_be16(0x888E))) {
+ txctl->use_minrate = 1;
+ txctl->min_rate = tx_info_priv->min_rate;
+ }
+ if (is_multicast_ether_addr(hdr->addr1))
+ txctl->mcast_rate = tx_info_priv->min_rate;
+ }
+
+}
+
+/* This function will setup additional txctl information, mostly rate stuff */
+/* FIXME: seqno, ps */
+static int ath_tx_prepare(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct ath_tx_control *txctl)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_hdr *hdr;
+ struct ath_rc_series *rcs;
+ struct ath_txq *txq = NULL;
+ const struct ath9k_rate_table *rt;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ struct ath_tx_info_priv *tx_info_priv;
+ int hdrlen;
+ u8 rix, antenna;
+ __le16 fc;
+ u8 *qc;
+
+ memset(txctl, 0, sizeof(struct ath_tx_control));
+
+ txctl->dev = sc;
+ hdr = (struct ieee80211_hdr *)skb->data;
+ hdrlen = ieee80211_get_hdrlen_from_skb(skb);
+ fc = hdr->frame_control;
+
+ rt = sc->sc_currates;
+ BUG_ON(!rt);
+
+ /* Fill misc fields */
+
+ spin_lock_bh(&sc->node_lock);
+ txctl->an = ath_node_get(sc, hdr->addr1);
+ /* create a temp node, if the node is not there already */
+ if (!txctl->an)
+ txctl->an = ath_node_attach(sc, hdr->addr1, 0);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (ieee80211_is_data_qos(fc)) {
+ qc = ieee80211_get_qos_ctl(hdr);
+ txctl->tidno = qc[0] & 0xf;
+ }
+
+ txctl->if_id = 0;
+ txctl->nextfraglen = 0;
+ txctl->frmlen = skb->len + FCS_LEN - (hdrlen & 3);
+ txctl->txpower = MAX_RATE_POWER; /* FIXME */
+
+ /* Fill Key related fields */
+
+ txctl->keytype = ATH9K_KEY_TYPE_CLEAR;
+ txctl->keyix = ATH9K_TXKEYIX_INVALID;
+
+ if (tx_info->control.hw_key) {
+ txctl->keyix = tx_info->control.hw_key->hw_key_idx;
+ txctl->frmlen += tx_info->control.icv_len;
+
+ if (sc->sc_keytype == ATH9K_CIPHER_WEP)
+ txctl->keytype = ATH9K_KEY_TYPE_WEP;
+ else if (sc->sc_keytype == ATH9K_CIPHER_TKIP)
+ txctl->keytype = ATH9K_KEY_TYPE_TKIP;
+ else if (sc->sc_keytype == ATH9K_CIPHER_AES_CCM)
+ txctl->keytype = ATH9K_KEY_TYPE_AES;
+ }
+
+ /* Fill packet type */
+
+ txctl->atype = get_hal_packet_type(hdr);
+
+ /* Fill qnum */
+
+ txctl->qnum = ath_get_hal_qnum(skb_get_queue_mapping(skb), sc);
+ txq = &sc->sc_txq[txctl->qnum];
+ spin_lock_bh(&txq->axq_lock);
+
+ /* Try to avoid running out of descriptors */
+ if (txq->axq_depth >= (ATH_TXBUF - 20)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: TX queue: %d is full, depth: %d\n",
+ __func__,
+ txctl->qnum,
+ txq->axq_depth);
+ ieee80211_stop_queue(hw, skb_get_queue_mapping(skb));
+ txq->stopped = 1;
+ spin_unlock_bh(&txq->axq_lock);
+ return -1;
+ }
+
+ spin_unlock_bh(&txq->axq_lock);
+
+ /* Fill rate */
+
+ fill_min_rates(skb, txctl);
+
+ /* Fill flags */
+
+ txctl->flags = ATH9K_TXDESC_CLRDMASK; /* needed for crypto errors */
+
+ if (tx_info->flags & IEEE80211_TX_CTL_NO_ACK)
+ tx_info->flags |= ATH9K_TXDESC_NOACK;
+ if (tx_info->flags & IEEE80211_TX_CTL_USE_RTS_CTS)
+ tx_info->flags |= ATH9K_TXDESC_RTSENA;
+
+ /*
+ * Setup for rate calculations.
+ */
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+ rcs = tx_info_priv->rcs;
+
+ if (ieee80211_is_data(fc) && !txctl->use_minrate) {
+
+ /* Enable HT only for DATA frames and not for EAPOL */
+ txctl->ht = (hw->conf.ht_conf.ht_supported &&
+ (tx_info->flags & IEEE80211_TX_CTL_AMPDU));
+
+ if (is_multicast_ether_addr(hdr->addr1)) {
+ rcs[0].rix = (u8)
+ ath_tx_findindex(rt, txctl->mcast_rate);
+
+ /*
+ * mcast packets are not re-tried.
+ */
+ rcs[0].tries = 1;
+ }
+ /* For HT capable stations, we save tidno for later use.
+ * We also override seqno set by upper layer with the one
+ * in tx aggregation state.
+ *
+ * First, the fragmentation stat is determined.
+ * If fragmentation is on, the sequence number is
+ * not overridden, since it has been
+ * incremented by the fragmentation routine.
+ */
+ if (likely(!(txctl->flags & ATH9K_TXDESC_FRAG_IS_ON)) &&
+ txctl->ht && sc->sc_txaggr) {
+ struct ath_atx_tid *tid;
+
+ tid = ATH_AN_2_TID(txctl->an, txctl->tidno);
+
+ hdr->seq_ctrl = cpu_to_le16(tid->seq_next <<
+ IEEE80211_SEQ_SEQ_SHIFT);
+ txctl->seqno = tid->seq_next;
+ INCR(tid->seq_next, IEEE80211_SEQ_MAX);
+ }
+ } else {
+ /* for management and control frames,
+ * or for NULL and EAPOL frames */
+ if (txctl->min_rate)
+ rcs[0].rix = ath_rate_findrateix(sc, txctl->min_rate);
+ else
+ rcs[0].rix = 0;
+ rcs[0].tries = ATH_MGT_TXMAXTRY;
+ }
+ rix = rcs[0].rix;
+
+ /*
+ * Calculate duration. This logically belongs in the 802.11
+ * layer but it lacks sufficient information to calculate it.
+ */
+ if ((txctl->flags & ATH9K_TXDESC_NOACK) == 0 && !ieee80211_is_ctl(fc)) {
+ u16 dur;
+ /*
+ * XXX not right with fragmentation.
+ */
+ if (sc->sc_flags & ATH_PREAMBLE_SHORT)
+ dur = rt->info[rix].spAckDuration;
+ else
+ dur = rt->info[rix].lpAckDuration;
+
+ if (le16_to_cpu(hdr->frame_control) &
+ IEEE80211_FCTL_MOREFRAGS) {
+ dur += dur; /* Add additional 'SIFS + ACK' */
+
+ /*
+ ** Compute size of next fragment in order to compute
+ ** durations needed to update NAV.
+ ** The last fragment uses the ACK duration only.
+ ** Add time for next fragment.
+ */
+ dur += ath9k_hw_computetxtime(sc->sc_ah, rt,
+ txctl->nextfraglen,
+ rix, sc->sc_flags & ATH_PREAMBLE_SHORT);
+ }
+
+ if (ieee80211_has_morefrags(fc) ||
+ (le16_to_cpu(hdr->seq_ctrl) & IEEE80211_SCTL_FRAG)) {
+ /*
+ ** Force hardware to use computed duration for next
+ ** fragment by disabling multi-rate retry, which
+ ** updates duration based on the multi-rate
+ ** duration table.
+ */
+ rcs[1].tries = rcs[2].tries = rcs[3].tries = 0;
+ rcs[1].rix = rcs[2].rix = rcs[3].rix = 0;
+ /* reset tries but keep rate index */
+ rcs[0].tries = ATH_TXMAXTRY;
+ }
+
+ hdr->duration_id = cpu_to_le16(dur);
+ }
+
+ /*
+ * Determine if a tx interrupt should be generated for
+ * this descriptor. We take a tx interrupt to reap
+ * descriptors when the h/w hits an EOL condition or
+ * when the descriptor is specifically marked to generate
+ * an interrupt. We periodically mark descriptors in this
+ * way to insure timely replenishing of the supply needed
+ * for sending frames. Defering interrupts reduces system
+ * load and potentially allows more concurrent work to be
+ * done but if done to aggressively can cause senders to
+ * backup.
+ *
+ * NB: use >= to deal with sc_txintrperiod changing
+ * dynamically through sysctl.
+ */
+ spin_lock_bh(&txq->axq_lock);
+ if ((++txq->axq_intrcnt >= sc->sc_txintrperiod)) {
+ txctl->flags |= ATH9K_TXDESC_INTREQ;
+ txq->axq_intrcnt = 0;
+ }
+ spin_unlock_bh(&txq->axq_lock);
+
+ if (is_multicast_ether_addr(hdr->addr1)) {
+ antenna = sc->sc_mcastantenna + 1;
+ sc->sc_mcastantenna = (sc->sc_mcastantenna + 1) & 0x1;
+ } else
+ antenna = sc->sc_txantenna;
+
+#ifdef USE_LEGACY_HAL
+ txctl->antenna = antenna;
+#endif
+ return 0;
+}
+
+/* To complete a chain of buffers associated a frame */
+
+static void ath_tx_complete_buf(struct ath_softc *sc,
+ struct ath_buf *bf,
+ struct list_head *bf_q,
+ int txok, int sendbar)
+{
+ struct sk_buff *skb = bf->bf_mpdu;
+ struct ath_xmit_status tx_status;
+ dma_addr_t *pa;
+
+ /*
+ * Set retry information.
+ * NB: Don't use the information in the descriptor, because the frame
+ * could be software retried.
+ */
+ tx_status.retries = bf->bf_retries;
+ tx_status.flags = 0;
+
+ if (sendbar)
+ tx_status.flags = ATH_TX_BAR;
+
+ if (!txok) {
+ tx_status.flags |= ATH_TX_ERROR;
+
+ if (bf->bf_isxretried)
+ tx_status.flags |= ATH_TX_XRETRY;
+ }
+ /* Unmap this frame */
+ pa = get_dma_mem_context(bf, bf_dmacontext);
+ pci_unmap_single(sc->pdev,
+ *pa,
+ skb->len,
+ PCI_DMA_TODEVICE);
+ /* complete this frame */
+ ath_tx_complete(sc, skb, &tx_status, bf->bf_node);
+
+ /*
+ * Return the list of ath_buf of this mpdu to free queue
+ */
+ spin_lock_bh(&sc->sc_txbuflock);
+ list_splice_tail_init(bf_q, &sc->sc_txbuf);
+ spin_unlock_bh(&sc->sc_txbuflock);
+}
+
+/*
+ * queue up a dest/ac pair for tx scheduling
+ * NB: must be called with txq lock held
+ */
+
+static void ath_tx_queue_tid(struct ath_txq *txq, struct ath_atx_tid *tid)
+{
+ struct ath_atx_ac *ac = tid->ac;
+
+ /*
+ * if tid is paused, hold off
+ */
+ if (tid->paused)
+ return;
+
+ /*
+ * add tid to ac atmost once
+ */
+ if (tid->sched)
+ return;
+
+ tid->sched = true;
+ list_add_tail(&tid->list, &ac->tid_q);
+
+ /*
+ * add node ac to txq atmost once
+ */
+ if (ac->sched)
+ return;
+
+ ac->sched = true;
+ list_add_tail(&ac->list, &txq->axq_acq);
+}
+
+/* pause a tid */
+
+static void ath_tx_pause_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
+{
+ struct ath_txq *txq = &sc->sc_txq[tid->ac->qnum];
+
+ spin_lock_bh(&txq->axq_lock);
+
+ tid->paused++;
+
+ spin_unlock_bh(&txq->axq_lock);
+}
+
+/* resume a tid and schedule aggregate */
+
+void ath_tx_resume_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
+{
+ struct ath_txq *txq = &sc->sc_txq[tid->ac->qnum];
+
+ ASSERT(tid->paused > 0);
+ spin_lock_bh(&txq->axq_lock);
+
+ tid->paused--;
+
+ if (tid->paused > 0)
+ goto unlock;
+
+ if (list_empty(&tid->buf_q))
+ goto unlock;
+
+ /*
+ * Add this TID to scheduler and try to send out aggregates
+ */
+ ath_tx_queue_tid(txq, tid);
+ ath_txq_schedule(sc, txq);
+unlock:
+ spin_unlock_bh(&txq->axq_lock);
+}
+
+/* Compute the number of bad frames */
+
+static int ath_tx_num_badfrms(struct ath_softc *sc,
+ struct ath_buf *bf, int txok)
+{
+ struct ath_node *an = bf->bf_node;
+ int isnodegone = (an->an_flags & ATH_NODE_CLEAN);
+ struct ath_buf *bf_last = bf->bf_lastbf;
+ struct ath_desc *ds = bf_last->bf_desc;
+ u16 seq_st = 0;
+ u32 ba[WME_BA_BMP_SIZE >> 5];
+ int ba_index;
+ int nbad = 0;
+ int isaggr = 0;
+
+ if (isnodegone || ds->ds_txstat.ts_flags == ATH9K_TX_SW_ABORTED)
+ return 0;
+
+ isaggr = bf->bf_isaggr;
+ if (isaggr) {
+ seq_st = ATH_DS_BA_SEQ(ds);
+ memcpy(ba, ATH_DS_BA_BITMAP(ds), WME_BA_BMP_SIZE >> 3);
+ }
+
+ while (bf) {
+ ba_index = ATH_BA_INDEX(seq_st, bf->bf_seqno);
+ if (!txok || (isaggr && !ATH_BA_ISSET(ba, ba_index)))
+ nbad++;
+
+ bf = bf->bf_next;
+ }
+
+ return nbad;
+}
+
+static void ath_tx_set_retry(struct ath_softc *sc, struct ath_buf *bf)
+{
+ struct sk_buff *skb;
+ struct ieee80211_hdr *hdr;
+
+ bf->bf_isretried = 1;
+ bf->bf_retries++;
+
+ skb = bf->bf_mpdu;
+ hdr = (struct ieee80211_hdr *)skb->data;
+ hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_RETRY);
+}
+
+/* Update block ack window */
+
+static void ath_tx_update_baw(struct ath_softc *sc,
+ struct ath_atx_tid *tid, int seqno)
+{
+ int index, cindex;
+
+ index = ATH_BA_INDEX(tid->seq_start, seqno);
+ cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
+
+ tid->tx_buf[cindex] = NULL;
+
+ while (tid->baw_head != tid->baw_tail && !tid->tx_buf[tid->baw_head]) {
+ INCR(tid->seq_start, IEEE80211_SEQ_MAX);
+ INCR(tid->baw_head, ATH_TID_MAX_BUFS);
+ }
+}
+
+/*
+ * ath_pkt_dur - compute packet duration (NB: not NAV)
+ *
+ * rix - rate index
+ * pktlen - total bytes (delims + data + fcs + pads + pad delims)
+ * width - 0 for 20 MHz, 1 for 40 MHz
+ * half_gi - to use 4us v/s 3.6 us for symbol time
+ */
+
+static u32 ath_pkt_duration(struct ath_softc *sc,
+ u8 rix,
+ struct ath_buf *bf,
+ int width,
+ int half_gi,
+ bool shortPreamble)
+{
+ const struct ath9k_rate_table *rt = sc->sc_currates;
+ u32 nbits, nsymbits, duration, nsymbols;
+ u8 rc;
+ int streams, pktlen;
+
+ pktlen = bf->bf_isaggr ? bf->bf_al : bf->bf_frmlen;
+ rc = rt->info[rix].rateCode;
+
+ /*
+ * for legacy rates, use old function to compute packet duration
+ */
+ if (!IS_HT_RATE(rc))
+ return ath9k_hw_computetxtime(sc->sc_ah,
+ rt,
+ pktlen,
+ rix,
+ shortPreamble);
+ /*
+ * find number of symbols: PLCP + data
+ */
+ nbits = (pktlen << 3) + OFDM_PLCP_BITS;
+ nsymbits = bits_per_symbol[HT_RC_2_MCS(rc)][width];
+ nsymbols = (nbits + nsymbits - 1) / nsymbits;
+
+ if (!half_gi)
+ duration = SYMBOL_TIME(nsymbols);
+ else
+ duration = SYMBOL_TIME_HALFGI(nsymbols);
+
+ /*
+ * addup duration for legacy/ht training and signal fields
+ */
+ streams = HT_RC_2_STREAMS(rc);
+ duration += L_STF + L_LTF + L_SIG + HT_SIG + HT_STF + HT_LTF(streams);
+ return duration;
+}
+
+/* Rate module function to set rate related fields in tx descriptor */
+
+static void ath_buf_set_rate(struct ath_softc *sc, struct ath_buf *bf)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ const struct ath9k_rate_table *rt;
+ struct ath_desc *ds = bf->bf_desc;
+ struct ath_desc *lastds = bf->bf_lastbf->bf_desc;
+ struct ath9k_11n_rate_series series[4];
+ int i, flags, rtsctsena = 0, dynamic_mimops = 0;
+ u32 ctsduration = 0;
+ u8 rix = 0, cix, ctsrate = 0;
+ u32 aggr_limit_with_rts = sc->sc_rtsaggrlimit;
+ struct ath_node *an = (struct ath_node *) bf->bf_node;
+
+ /*
+ * get the cix for the lowest valid rix.
+ */
+ rt = sc->sc_currates;
+ for (i = 4; i--;) {
+ if (bf->bf_rcs[i].tries) {
+ rix = bf->bf_rcs[i].rix;
+ break;
+ }
+ }
+ flags = (bf->bf_flags & (ATH9K_TXDESC_RTSENA | ATH9K_TXDESC_CTSENA));
+ cix = rt->info[rix].controlRate;
+
+ /*
+ * If 802.11g protection is enabled, determine whether
+ * to use RTS/CTS or just CTS. Note that this is only
+ * done for OFDM/HT unicast frames.
+ */
+ if (sc->sc_protmode != PROT_M_NONE &&
+ (rt->info[rix].phy == PHY_OFDM ||
+ rt->info[rix].phy == PHY_HT) &&
+ (bf->bf_flags & ATH9K_TXDESC_NOACK) == 0) {
+ if (sc->sc_protmode == PROT_M_RTSCTS)
+ flags = ATH9K_TXDESC_RTSENA;
+ else if (sc->sc_protmode == PROT_M_CTSONLY)
+ flags = ATH9K_TXDESC_CTSENA;
+
+ cix = rt->info[sc->sc_protrix].controlRate;
+ rtsctsena = 1;
+ }
+
+ /* For 11n, the default behavior is to enable RTS for
+ * hw retried frames. We enable the global flag here and
+ * let rate series flags determine which rates will actually
+ * use RTS.
+ */
+ if ((ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) && bf->bf_isdata) {
+ BUG_ON(!an);
+ /*
+ * 802.11g protection not needed, use our default behavior
+ */
+ if (!rtsctsena)
+ flags = ATH9K_TXDESC_RTSENA;
+ /*
+ * For dynamic MIMO PS, RTS needs to precede the first aggregate
+ * and the second aggregate should have any protection at all.
+ */
+ if (an->an_smmode == ATH_SM_PWRSAV_DYNAMIC) {
+ if (!bf->bf_aggrburst) {
+ flags = ATH9K_TXDESC_RTSENA;
+ dynamic_mimops = 1;
+ } else {
+ flags = 0;
+ }
+ }
+ }
+
+ /*
+ * Set protection if aggregate protection on
+ */
+ if (sc->sc_config.ath_aggr_prot &&
+ (!bf->bf_isaggr || (bf->bf_isaggr && bf->bf_al < 8192))) {
+ flags = ATH9K_TXDESC_RTSENA;
+ cix = rt->info[sc->sc_protrix].controlRate;
+ rtsctsena = 1;
+ }
+
+ /*
+ * For AR5416 - RTS cannot be followed by a frame larger than 8K.
+ */
+ if (bf->bf_isaggr && (bf->bf_al > aggr_limit_with_rts)) {
+ /*
+ * Ensure that in the case of SM Dynamic power save
+ * while we are bursting the second aggregate the
+ * RTS is cleared.
+ */
+ flags &= ~(ATH9K_TXDESC_RTSENA);
+ }
+
+ /*
+ * CTS transmit rate is derived from the transmit rate
+ * by looking in the h/w rate table. We must also factor
+ * in whether or not a short preamble is to be used.
+ */
+ /* NB: cix is set above where RTS/CTS is enabled */
+ BUG_ON(cix == 0xff);
+ ctsrate = rt->info[cix].rateCode |
+ (bf->bf_shpreamble ? rt->info[cix].shortPreamble : 0);
+
+ /*
+ * Setup HAL rate series
+ */
+ memzero(series, sizeof(struct ath9k_11n_rate_series) * 4);
+
+ for (i = 0; i < 4; i++) {
+ if (!bf->bf_rcs[i].tries)
+ continue;
+
+ rix = bf->bf_rcs[i].rix;
+
+ series[i].Rate = rt->info[rix].rateCode |
+ (bf->bf_shpreamble ? rt->info[rix].shortPreamble : 0);
+
+ series[i].Tries = bf->bf_rcs[i].tries;
+
+ series[i].RateFlags = (
+ (bf->bf_rcs[i].flags & ATH_RC_RTSCTS_FLAG) ?
+ ATH9K_RATESERIES_RTS_CTS : 0) |
+ ((bf->bf_rcs[i].flags & ATH_RC_CW40_FLAG) ?
+ ATH9K_RATESERIES_2040 : 0) |
+ ((bf->bf_rcs[i].flags & ATH_RC_SGI_FLAG) ?
+ ATH9K_RATESERIES_HALFGI : 0);
+
+ series[i].PktDuration = ath_pkt_duration(
+ sc, rix, bf,
+ (bf->bf_rcs[i].flags & ATH_RC_CW40_FLAG) != 0,
+ (bf->bf_rcs[i].flags & ATH_RC_SGI_FLAG),
+ bf->bf_shpreamble);
+
+ if ((an->an_smmode == ATH_SM_PWRSAV_STATIC) &&
+ (bf->bf_rcs[i].flags & ATH_RC_DS_FLAG) == 0) {
+ /*
+ * When sending to an HT node that has enabled static
+ * SM/MIMO power save, send at single stream rates but
+ * use maximum allowed transmit chains per user,
+ * hardware, regulatory, or country limits for
+ * better range.
+ */
+ series[i].ChSel = sc->sc_tx_chainmask;
+ } else {
+ if (bf->bf_ht)
+ series[i].ChSel =
+ ath_chainmask_sel_logic(sc, an);
+ else
+ series[i].ChSel = sc->sc_tx_chainmask;
+ }
+
+ if (rtsctsena)
+ series[i].RateFlags |= ATH9K_RATESERIES_RTS_CTS;
+
+ /*
+ * Set RTS for all rates if node is in dynamic powersave
+ * mode and we are using dual stream rates.
+ */
+ if (dynamic_mimops && (bf->bf_rcs[i].flags & ATH_RC_DS_FLAG))
+ series[i].RateFlags |= ATH9K_RATESERIES_RTS_CTS;
+ }
+
+ /*
+ * For non-HT devices, calculate RTS/CTS duration in software
+ * and disable multi-rate retry.
+ */
+ if (flags && !(ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)) {
+ /*
+ * Compute the transmit duration based on the frame
+ * size and the size of an ACK frame. We call into the
+ * HAL to do the computation since it depends on the
+ * characteristics of the actual PHY being used.
+ *
+ * NB: CTS is assumed the same size as an ACK so we can
+ * use the precalculated ACK durations.
+ */
+ if (flags & ATH9K_TXDESC_RTSENA) { /* SIFS + CTS */
+ ctsduration += bf->bf_shpreamble ?
+ rt->info[cix].spAckDuration :
+ rt->info[cix].lpAckDuration;
+ }
+
+ ctsduration += series[0].PktDuration;
+
+ if ((bf->bf_flags & ATH9K_TXDESC_NOACK) == 0) { /* SIFS + ACK */
+ ctsduration += bf->bf_shpreamble ?
+ rt->info[rix].spAckDuration :
+ rt->info[rix].lpAckDuration;
+ }
+
+ /*
+ * Disable multi-rate retry when using RTS/CTS by clearing
+ * series 1, 2 and 3.
+ */
+ memzero(&series[1], sizeof(struct ath9k_11n_rate_series) * 3);
+ }
+
+ /*
+ * set dur_update_en for l-sig computation except for PS-Poll frames
+ */
+ ath9k_hw_set11n_ratescenario(ah, ds, lastds,
+ !bf->bf_ispspoll,
+ ctsrate,
+ ctsduration,
+ series, 4, flags);
+ if (sc->sc_config.ath_aggr_prot && flags)
+ ath9k_hw_set11n_burstduration(ah, ds, 8192);
+}
+
+/*
+ * Function to send a normal HT (non-AMPDU) frame
+ * NB: must be called with txq lock held
+ */
+
+static int ath_tx_send_normal(struct ath_softc *sc,
+ struct ath_txq *txq,
+ struct ath_atx_tid *tid,
+ struct list_head *bf_head)
+{
+ struct ath_buf *bf;
+ struct sk_buff *skb;
+ struct ieee80211_tx_info *tx_info;
+ struct ath_tx_info_priv *tx_info_priv;
+
+ BUG_ON(list_empty(bf_head));
+
+ bf = list_first_entry(bf_head, struct ath_buf, list);
+ bf->bf_isampdu = 0; /* regular HT frame */
+
+ skb = (struct sk_buff *)bf->bf_mpdu;
+ tx_info = IEEE80211_SKB_CB(skb);
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+ memcpy(bf->bf_rcs, tx_info_priv->rcs, 4 * sizeof(tx_info_priv->rcs[0]));
+
+ /* update starting sequence number for subsequent ADDBA request */
+ INCR(tid->seq_start, IEEE80211_SEQ_MAX);
+
+ /* Queue to h/w without aggregation */
+ bf->bf_nframes = 1;
+ bf->bf_lastbf = bf->bf_lastfrm; /* one single frame */
+ ath_buf_set_rate(sc, bf);
+ ath_tx_txqaddbuf(sc, txq, bf_head);
+
+ return 0;
+}
+
+/* flush tid's software queue and send frames as non-ampdu's */
+
+static void ath_tx_flush_tid(struct ath_softc *sc, struct ath_atx_tid *tid)
+{
+ struct ath_txq *txq = &sc->sc_txq[tid->ac->qnum];
+ struct ath_buf *bf;
+ struct list_head bf_head;
+ INIT_LIST_HEAD(&bf_head);
+
+ ASSERT(tid->paused > 0);
+ spin_lock_bh(&txq->axq_lock);
+
+ tid->paused--;
+
+ if (tid->paused > 0) {
+ spin_unlock_bh(&txq->axq_lock);
+ return;
+ }
+
+ while (!list_empty(&tid->buf_q)) {
+ bf = list_first_entry(&tid->buf_q, struct ath_buf, list);
+ ASSERT(!bf->bf_isretried);
+ list_cut_position(&bf_head, &tid->buf_q, &bf->bf_lastfrm->list);
+ ath_tx_send_normal(sc, txq, tid, &bf_head);
+ }
+
+ spin_unlock_bh(&txq->axq_lock);
+}
+
+/* Completion routine of an aggregate */
+
+static void ath_tx_complete_aggr_rifs(struct ath_softc *sc,
+ struct ath_txq *txq,
+ struct ath_buf *bf,
+ struct list_head *bf_q,
+ int txok)
+{
+ struct ath_node *an = bf->bf_node;
+ struct ath_atx_tid *tid = ATH_AN_2_TID(an, bf->bf_tidno);
+ struct ath_buf *bf_last = bf->bf_lastbf;
+ struct ath_desc *ds = bf_last->bf_desc;
+ struct ath_buf *bf_next, *bf_lastq = NULL;
+ struct list_head bf_head, bf_pending;
+ u16 seq_st = 0;
+ u32 ba[WME_BA_BMP_SIZE >> 5];
+ int isaggr, txfail, txpending, sendbar = 0, needreset = 0;
+ int isnodegone = (an->an_flags & ATH_NODE_CLEAN);
+
+ isaggr = bf->bf_isaggr;
+ if (isaggr) {
+ if (txok) {
+ if (ATH_DS_TX_BA(ds)) {
+ /*
+ * extract starting sequence and
+ * block-ack bitmap
+ */
+ seq_st = ATH_DS_BA_SEQ(ds);
+ memcpy(ba,
+ ATH_DS_BA_BITMAP(ds),
+ WME_BA_BMP_SIZE >> 3);
+ } else {
+ memzero(ba, WME_BA_BMP_SIZE >> 3);
+
+ /*
+ * AR5416 can become deaf/mute when BA
+ * issue happens. Chip needs to be reset.
+ * But AP code may have sychronization issues
+ * when perform internal reset in this routine.
+ * Only enable reset in STA mode for now.
+ */
+ if (sc->sc_opmode == ATH9K_M_STA)
+ needreset = 1;
+ }
+ } else {
+ memzero(ba, WME_BA_BMP_SIZE >> 3);
+ }
+ }
+
+ INIT_LIST_HEAD(&bf_pending);
+ INIT_LIST_HEAD(&bf_head);
+
+ while (bf) {
+ txfail = txpending = 0;
+ bf_next = bf->bf_next;
+
+ if (ATH_BA_ISSET(ba, ATH_BA_INDEX(seq_st, bf->bf_seqno))) {
+ /* transmit completion, subframe is
+ * acked by block ack */
+ } else if (!isaggr && txok) {
+ /* transmit completion */
+ } else {
+
+ if (!tid->cleanup_inprogress && !isnodegone &&
+ ds->ds_txstat.ts_flags != ATH9K_TX_SW_ABORTED) {
+ if (bf->bf_retries < ATH_MAX_SW_RETRIES) {
+ ath_tx_set_retry(sc, bf);
+ txpending = 1;
+ } else {
+ bf->bf_isxretried = 1;
+ txfail = 1;
+ sendbar = 1;
+ }
+ } else {
+ /*
+ * cleanup in progress, just fail
+ * the un-acked sub-frames
+ */
+ txfail = 1;
+ }
+ }
+ /*
+ * Remove ath_buf's of this sub-frame from aggregate queue.
+ */
+ if (bf_next == NULL) { /* last subframe in the aggregate */
+ ASSERT(bf->bf_lastfrm == bf_last);
+
+ /*
+ * The last descriptor of the last sub frame could be
+ * a holding descriptor for h/w. If that's the case,
+ * bf->bf_lastfrm won't be in the bf_q.
+ * Make sure we handle bf_q properly here.
+ */
+
+ if (!list_empty(bf_q)) {
+ bf_lastq = list_entry(bf_q->prev,
+ struct ath_buf, list);
+ list_cut_position(&bf_head,
+ bf_q, &bf_lastq->list);
+ } else {
+ /*
+ * XXX: if the last subframe only has one
+ * descriptor which is also being used as
+ * a holding descriptor. Then the ath_buf
+ * is not in the bf_q at all.
+ */
+ INIT_LIST_HEAD(&bf_head);
+ }
+ } else {
+ ASSERT(!list_empty(bf_q));
+ list_cut_position(&bf_head,
+ bf_q, &bf->bf_lastfrm->list);
+ }
+
+ if (!txpending) {
+ /*
+ * complete the acked-ones/xretried ones; update
+ * block-ack window
+ */
+ spin_lock_bh(&txq->axq_lock);
+ ath_tx_update_baw(sc, tid, bf->bf_seqno);
+ spin_unlock_bh(&txq->axq_lock);
+
+ /* complete this sub-frame */
+ ath_tx_complete_buf(sc, bf, &bf_head, !txfail, sendbar);
+ } else {
+ /*
+ * retry the un-acked ones
+ */
+ /*
+ * XXX: if the last descriptor is holding descriptor,
+ * in order to requeue the frame to software queue, we
+ * need to allocate a new descriptor and
+ * copy the content of holding descriptor to it.
+ */
+ if (bf->bf_next == NULL &&
+ bf_last->bf_status & ATH_BUFSTATUS_STALE) {
+ struct ath_buf *tbf;
+
+ /* allocate new descriptor */
+ spin_lock_bh(&sc->sc_txbuflock);
+ ASSERT(!list_empty((&sc->sc_txbuf)));
+ tbf = list_first_entry(&sc->sc_txbuf,
+ struct ath_buf, list);
+ list_del(&tbf->list);
+ spin_unlock_bh(&sc->sc_txbuflock);
+
+ ATH_TXBUF_RESET(tbf);
+
+ /* copy descriptor content */
+ tbf->bf_mpdu = bf_last->bf_mpdu;
+ tbf->bf_node = bf_last->bf_node;
+ tbf->bf_buf_addr = bf_last->bf_buf_addr;
+ *(tbf->bf_desc) = *(bf_last->bf_desc);
+
+ /* link it to the frame */
+ if (bf_lastq) {
+ bf_lastq->bf_desc->ds_link =
+ tbf->bf_daddr;
+ bf->bf_lastfrm = tbf;
+ ath9k_hw_cleartxdesc(sc->sc_ah,
+ bf->bf_lastfrm->bf_desc);
+ } else {
+ tbf->bf_state = bf_last->bf_state;
+ tbf->bf_lastfrm = tbf;
+ ath9k_hw_cleartxdesc(sc->sc_ah,
+ tbf->bf_lastfrm->bf_desc);
+
+ /* copy the DMA context */
+ copy_dma_mem_context(
+ get_dma_mem_context(tbf,
+ bf_dmacontext),
+ get_dma_mem_context(bf_last,
+ bf_dmacontext));
+ }
+ list_add_tail(&tbf->list, &bf_head);
+ } else {
+ /*
+ * Clear descriptor status words for
+ * software retry
+ */
+ ath9k_hw_cleartxdesc(sc->sc_ah,
+ bf->bf_lastfrm->bf_desc);
+ }
+
+ /*
+ * Put this buffer to the temporary pending
+ * queue to retain ordering
+ */
+ list_splice_tail_init(&bf_head, &bf_pending);
+ }
+
+ bf = bf_next;
+ }
+
+ /*
+ * node is already gone. no more assocication
+ * with the node. the node might have been freed
+ * any node acces can result in panic.note tid
+ * is part of the node.
+ */
+ if (isnodegone)
+ return;
+
+ if (tid->cleanup_inprogress) {
+ /* check to see if we're done with cleaning the h/w queue */
+ spin_lock_bh(&txq->axq_lock);
+
+ if (tid->baw_head == tid->baw_tail) {
+ tid->addba_exchangecomplete = 0;
+ tid->addba_exchangeattempts = 0;
+ spin_unlock_bh(&txq->axq_lock);
+
+ tid->cleanup_inprogress = false;
+
+ /* send buffered frames as singles */
+ ath_tx_flush_tid(sc, tid);
+ } else
+ spin_unlock_bh(&txq->axq_lock);
+
+ return;
+ }
+
+ /*
+ * prepend un-acked frames to the beginning of the pending frame queue
+ */
+ if (!list_empty(&bf_pending)) {
+ spin_lock_bh(&txq->axq_lock);
+ /* Note: we _prepend_, we _do_not_ at to
+ * the end of the queue ! */
+ list_splice(&bf_pending, &tid->buf_q);
+ ath_tx_queue_tid(txq, tid);
+ spin_unlock_bh(&txq->axq_lock);
+ }
+
+ if (needreset)
+ ath_internal_reset(sc);
+
+ return;
+}
+
+/* Process completed xmit descriptors from the specified queue */
+
+static int ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_buf *bf, *lastbf, *bf_held = NULL;
+ struct list_head bf_head;
+ struct ath_desc *ds, *tmp_ds;
+ struct sk_buff *skb;
+ struct ieee80211_tx_info *tx_info;
+ struct ath_tx_info_priv *tx_info_priv;
+ int nacked, txok, nbad = 0, isrifs = 0;
+ int status;
+
+ DPRINTF(sc, ATH_DBG_QUEUE,
+ "%s: tx queue %d (%x), link %p\n", __func__,
+ txq->axq_qnum, ath9k_hw_gettxbuf(sc->sc_ah, txq->axq_qnum),
+ txq->axq_link);
+
+ nacked = 0;
+ for (;;) {
+ spin_lock_bh(&txq->axq_lock);
+ txq->axq_intrcnt = 0; /* reset periodic desc intr count */
+ if (list_empty(&txq->axq_q)) {
+ txq->axq_link = NULL;
+ txq->axq_linkbuf = NULL;
+ spin_unlock_bh(&txq->axq_lock);
+ break;
+ }
+ bf = list_first_entry(&txq->axq_q, struct ath_buf, list);
+
+ /*
+ * There is a race condition that a BH gets scheduled
+ * after sw writes TxE and before hw re-load the last
+ * descriptor to get the newly chained one.
+ * Software must keep the last DONE descriptor as a
+ * holding descriptor - software does so by marking
+ * it with the STALE flag.
+ */
+ bf_held = NULL;
+ if (bf->bf_status & ATH_BUFSTATUS_STALE) {
+ bf_held = bf;
+ if (list_is_last(&bf_held->list, &txq->axq_q)) {
+ /* FIXME:
+ * The holding descriptor is the last
+ * descriptor in queue. It's safe to remove
+ * the last holding descriptor in BH context.
+ */
+ spin_unlock_bh(&txq->axq_lock);
+ break;
+ } else {
+ /* Lets work with the next buffer now */
+ bf = list_entry(bf_held->list.next,
+ struct ath_buf, list);
+ }
+ }
+
+ lastbf = bf->bf_lastbf;
+ ds = lastbf->bf_desc; /* NB: last decriptor */
+
+ status = ath9k_hw_txprocdesc(ah, ds);
+ if (status == -EINPROGRESS) {
+ spin_unlock_bh(&txq->axq_lock);
+ break;
+ }
+ if (bf->bf_desc == txq->axq_lastdsWithCTS)
+ txq->axq_lastdsWithCTS = NULL;
+ if (ds == txq->axq_gatingds)
+ txq->axq_gatingds = NULL;
+
+ /*
+ * Remove ath_buf's of the same transmit unit from txq,
+ * however leave the last descriptor back as the holding
+ * descriptor for hw.
+ */
+ lastbf->bf_status |= ATH_BUFSTATUS_STALE;
+ INIT_LIST_HEAD(&bf_head);
+
+ if (!list_is_singular(&lastbf->list))
+ list_cut_position(&bf_head,
+ &txq->axq_q, lastbf->list.prev);
+
+ txq->axq_depth--;
+
+ if (bf->bf_isaggr)
+ txq->axq_aggr_depth--;
+
+ txok = (ds->ds_txstat.ts_status == 0);
+
+ spin_unlock_bh(&txq->axq_lock);
+
+ if (bf_held) {
+ list_del(&bf_held->list);
+ spin_lock_bh(&sc->sc_txbuflock);
+ list_add_tail(&bf_held->list, &sc->sc_txbuf);
+ spin_unlock_bh(&sc->sc_txbuflock);
+ }
+
+ if (!bf->bf_isampdu) {
+ /*
+ * This frame is sent out as a single frame.
+ * Use hardware retry status for this frame.
+ */
+ bf->bf_retries = ds->ds_txstat.ts_longretry;
+ if (ds->ds_txstat.ts_status & ATH9K_TXERR_XRETRY)
+ bf->bf_isxretried = 1;
+ nbad = 0;
+ } else {
+ nbad = ath_tx_num_badfrms(sc, bf, txok);
+ }
+ skb = bf->bf_mpdu;
+ tx_info = IEEE80211_SKB_CB(skb);
+ tx_info_priv = (struct ath_tx_info_priv *)
+ tx_info->driver_data[0];
+ if (ds->ds_txstat.ts_status & ATH9K_TXERR_FILT)
+ tx_info->flags |= IEEE80211_TX_STAT_TX_FILTERED;
+ if ((ds->ds_txstat.ts_status & ATH9K_TXERR_FILT) == 0 &&
+ (bf->bf_flags & ATH9K_TXDESC_NOACK) == 0) {
+ if (ds->ds_txstat.ts_status == 0)
+ nacked++;
+
+ if (bf->bf_isdata) {
+ if (isrifs)
+ tmp_ds = bf->bf_rifslast->bf_desc;
+ else
+ tmp_ds = ds;
+ memcpy(&tx_info_priv->tx,
+ &tmp_ds->ds_txstat,
+ sizeof(tx_info_priv->tx));
+ tx_info_priv->n_frames = bf->bf_nframes;
+ tx_info_priv->n_bad_frames = nbad;
+ }
+ }
+
+ /*
+ * Complete this transmit unit
+ */
+ if (bf->bf_isampdu)
+ ath_tx_complete_aggr_rifs(sc, txq, bf, &bf_head, txok);
+ else
+ ath_tx_complete_buf(sc, bf, &bf_head, txok, 0);
+
+ /* Wake up mac80211 queue */
+
+ spin_lock_bh(&txq->axq_lock);
+ if (txq->stopped && ath_txq_depth(sc, txq->axq_qnum) <=
+ (ATH_TXBUF - 20)) {
+ int qnum;
+ qnum = ath_get_mac80211_qnum(txq->axq_qnum, sc);
+ if (qnum != -1) {
+ ieee80211_wake_queue(sc->hw, qnum);
+ txq->stopped = 0;
+ }
+
+ }
+
+ /*
+ * schedule any pending packets if aggregation is enabled
+ */
+ if (sc->sc_txaggr)
+ ath_txq_schedule(sc, txq);
+ spin_unlock_bh(&txq->axq_lock);
+ }
+ return nacked;
+}
+
+static void ath_tx_stopdma(struct ath_softc *sc, struct ath_txq *txq)
+{
+ struct ath_hal *ah = sc->sc_ah;
+
+ (void) ath9k_hw_stoptxdma(ah, txq->axq_qnum);
+ DPRINTF(sc, ATH_DBG_XMIT, "%s: tx queue [%u] %x, link %p\n",
+ __func__, txq->axq_qnum,
+ ath9k_hw_gettxbuf(ah, txq->axq_qnum), txq->axq_link);
+}
+
+/* Drain only the data queues */
+
+static void ath_drain_txdataq(struct ath_softc *sc, bool retry_tx)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int i;
+ int npend = 0;
+ enum ath9k_ht_macmode ht_macmode = ath_cwm_macmode(sc);
+
+ /* XXX return value */
+ if (!sc->sc_invalid) {
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i)) {
+ ath_tx_stopdma(sc, &sc->sc_txq[i]);
+
+ /* The TxDMA may not really be stopped.
+ * Double check the hal tx pending count */
+ npend += ath9k_hw_numtxpending(ah,
+ sc->sc_txq[i].axq_qnum);
+ }
+ }
+ }
+
+ if (npend) {
+ int status;
+
+ /* TxDMA not stopped, reset the hal */
+ DPRINTF(sc, ATH_DBG_XMIT,
+ "%s: Unable to stop TxDMA. Reset HAL!\n", __func__);
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, sc->sc_opmode,
+ &sc->sc_curchan, ht_macmode,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, true, &status)) {
+
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset hardware; hal status %u\n",
+ __func__,
+ status);
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+ }
+
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i))
+ ath_tx_draintxq(sc, &sc->sc_txq[i], retry_tx);
+ }
+}
+
+/* Add a sub-frame to block ack window */
+
+static void ath_tx_addto_baw(struct ath_softc *sc,
+ struct ath_atx_tid *tid,
+ struct ath_buf *bf)
+{
+ int index, cindex;
+
+ if (bf->bf_isretried)
+ return;
+
+ index = ATH_BA_INDEX(tid->seq_start, bf->bf_seqno);
+ cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);
+
+ ASSERT(tid->tx_buf[cindex] == NULL);
+ tid->tx_buf[cindex] = bf;
+
+ if (index >= ((tid->baw_tail - tid->baw_head) &
+ (ATH_TID_MAX_BUFS - 1))) {
+ tid->baw_tail = cindex;
+ INCR(tid->baw_tail, ATH_TID_MAX_BUFS);
+ }
+}
+
+/*
+ * Function to send an A-MPDU
+ * NB: must be called with txq lock held
+ */
+
+static int ath_tx_send_ampdu(struct ath_softc *sc,
+ struct ath_txq *txq,
+ struct ath_atx_tid *tid,
+ struct list_head *bf_head,
+ struct ath_tx_control *txctl)
+{
+ struct ath_buf *bf;
+ struct sk_buff *skb;
+ struct ieee80211_tx_info *tx_info;
+ struct ath_tx_info_priv *tx_info_priv;
+
+ BUG_ON(list_empty(bf_head));
+
+ bf = list_first_entry(bf_head, struct ath_buf, list);
+ bf->bf_isampdu = 1;
+ bf->bf_seqno = txctl->seqno; /* save seqno and tidno in buffer */
+ bf->bf_tidno = txctl->tidno;
+
+ /*
+ * Do not queue to h/w when any of the following conditions is true:
+ * - there are pending frames in software queue
+ * - the TID is currently paused for ADDBA/BAR request
+ * - seqno is not within block-ack window
+ * - h/w queue depth exceeds low water mark
+ */
+ if (!list_empty(&tid->buf_q) || tid->paused ||
+ !BAW_WITHIN(tid->seq_start, tid->baw_size, bf->bf_seqno) ||
+ txq->axq_depth >= ATH_AGGR_MIN_QDEPTH) {
+ /*
+ * Add this frame to software queue for scheduling later
+ * for aggregation.
+ */
+ list_splice_tail_init(bf_head, &tid->buf_q);
+ ath_tx_queue_tid(txq, tid);
+ return 0;
+ }
+
+ skb = (struct sk_buff *)bf->bf_mpdu;
+ tx_info = IEEE80211_SKB_CB(skb);
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+ memcpy(bf->bf_rcs, tx_info_priv->rcs, 4 * sizeof(tx_info_priv->rcs[0]));
+
+ /* Add sub-frame to BAW */
+ ath_tx_addto_baw(sc, tid, bf);
+
+ /* Queue to h/w without aggregation */
+ bf->bf_nframes = 1;
+ bf->bf_lastbf = bf->bf_lastfrm; /* one single frame */
+ ath_buf_set_rate(sc, bf);
+ ath_tx_txqaddbuf(sc, txq, bf_head);
+ return 0;
+}
+
+/*
+ * looks up the rate
+ * returns aggr limit based on lowest of the rates
+ */
+
+static u32 ath_lookup_rate(struct ath_softc *sc,
+ struct ath_buf *bf)
+{
+ const struct ath9k_rate_table *rt = sc->sc_currates;
+ struct sk_buff *skb;
+ struct ieee80211_tx_info *tx_info;
+ struct ath_tx_info_priv *tx_info_priv;
+ u32 max_4ms_framelen, frame_length;
+ u16 aggr_limit, legacy = 0, maxampdu;
+ int i;
+
+
+ skb = (struct sk_buff *)bf->bf_mpdu;
+ tx_info = IEEE80211_SKB_CB(skb);
+ tx_info_priv = (struct ath_tx_info_priv *)
+ tx_info->driver_data[0];
+ memcpy(bf->bf_rcs,
+ tx_info_priv->rcs, 4 * sizeof(tx_info_priv->rcs[0]));
+
+ /*
+ * Find the lowest frame length among the rate series that will have a
+ * 4ms transmit duration.
+ * TODO - TXOP limit needs to be considered.
+ */
+ max_4ms_framelen = ATH_AMPDU_LIMIT_MAX;
+
+ for (i = 0; i < 4; i++) {
+ if (bf->bf_rcs[i].tries) {
+ frame_length = bf->bf_rcs[i].max_4ms_framelen;
+
+ if (rt->info[bf->bf_rcs[i].rix].phy != PHY_HT) {
+ legacy = 1;
+ break;
+ }
+
+ max_4ms_framelen = min(max_4ms_framelen, frame_length);
+ }
+ }
+
+ /*
+ * limit aggregate size by the minimum rate if rate selected is
+ * not a probe rate, if rate selected is a probe rate then
+ * avoid aggregation of this packet.
+ */
+ if (tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE || legacy)
+ return 0;
+
+ aggr_limit = min(max_4ms_framelen,
+ (u32)ATH_AMPDU_LIMIT_DEFAULT);
+
+ /*
+ * h/w can accept aggregates upto 16 bit lengths (65535).
+ * The IE, however can hold upto 65536, which shows up here
+ * as zero. Ignore 65536 since we are constrained by hw.
+ */
+ maxampdu = sc->sc_ht_info.maxampdu;
+ if (maxampdu)
+ aggr_limit = min(aggr_limit, maxampdu);
+
+ return aggr_limit;
+}
+
+/*
+ * returns the number of delimiters to be added to
+ * meet the minimum required mpdudensity.
+ * caller should make sure that the rate is HT rate .
+ */
+
+static int ath_compute_num_delims(struct ath_softc *sc,
+ struct ath_buf *bf,
+ u16 frmlen)
+{
+ const struct ath9k_rate_table *rt = sc->sc_currates;
+ u32 nsymbits, nsymbols, mpdudensity;
+ u16 minlen;
+ u8 rc, flags, rix;
+ int width, half_gi, ndelim, mindelim;
+
+ /* Select standard number of delimiters based on frame length alone */
+ ndelim = ATH_AGGR_GET_NDELIM(frmlen);
+
+ /*
+ * If encryption enabled, hardware requires some more padding between
+ * subframes.
+ * TODO - this could be improved to be dependent on the rate.
+ * The hardware can keep up at lower rates, but not higher rates
+ */
+ if (bf->bf_keytype != ATH9K_KEY_TYPE_CLEAR)
+ ndelim += ATH_AGGR_ENCRYPTDELIM;
+
+ /*
+ * Convert desired mpdu density from microeconds to bytes based
+ * on highest rate in rate series (i.e. first rate) to determine
+ * required minimum length for subframe. Take into account
+ * whether high rate is 20 or 40Mhz and half or full GI.
+ */
+ mpdudensity = sc->sc_ht_info.mpdudensity;
+
+ /*
+ * If there is no mpdu density restriction, no further calculation
+ * is needed.
+ */
+ if (mpdudensity == 0)
+ return ndelim;
+
+ rix = bf->bf_rcs[0].rix;
+ flags = bf->bf_rcs[0].flags;
+ rc = rt->info[rix].rateCode;
+ width = (flags & ATH_RC_CW40_FLAG) ? 1 : 0;
+ half_gi = (flags & ATH_RC_SGI_FLAG) ? 1 : 0;
+
+ if (half_gi)
+ nsymbols = NUM_SYMBOLS_PER_USEC_HALFGI(mpdudensity);
+ else
+ nsymbols = NUM_SYMBOLS_PER_USEC(mpdudensity);
+
+ if (nsymbols == 0)
+ nsymbols = 1;
+
+ nsymbits = bits_per_symbol[HT_RC_2_MCS(rc)][width];
+ minlen = (nsymbols * nsymbits) / BITS_PER_BYTE;
+
+ /* Is frame shorter than required minimum length? */
+ if (frmlen < minlen) {
+ /* Get the minimum number of delimiters required. */
+ mindelim = (minlen - frmlen) / ATH_AGGR_DELIM_SZ;
+ ndelim = max(mindelim, ndelim);
+ }
+
+ return ndelim;
+}
+
+/*
+ * For aggregation from software buffer queue.
+ * NB: must be called with txq lock held
+ */
+
+static enum ATH_AGGR_STATUS ath_tx_form_aggr(struct ath_softc *sc,
+ struct ath_atx_tid *tid,
+ struct list_head *bf_q,
+ struct ath_buf **bf_last,
+ struct aggr_rifs_param *param,
+ int *prev_frames)
+{
+#define PADBYTES(_len) ((4 - ((_len) % 4)) % 4)
+ struct ath_buf *bf, *tbf, *bf_first, *bf_prev = NULL;
+ struct list_head bf_head;
+ int rl = 0, nframes = 0, ndelim;
+ u16 aggr_limit = 0, al = 0, bpad = 0,
+ al_delta, h_baw = tid->baw_size / 2;
+ enum ATH_AGGR_STATUS status = ATH_AGGR_DONE;
+ int prev_al = 0, is_ds_rate = 0;
+ INIT_LIST_HEAD(&bf_head);
+
+ BUG_ON(list_empty(&tid->buf_q));
+
+ bf_first = list_first_entry(&tid->buf_q, struct ath_buf, list);
+
+ do {
+ bf = list_first_entry(&tid->buf_q, struct ath_buf, list);
+
+ /*
+ * do not step over block-ack window
+ */
+ if (!BAW_WITHIN(tid->seq_start, tid->baw_size, bf->bf_seqno)) {
+ status = ATH_AGGR_BAW_CLOSED;
+ break;
+ }
+
+ if (!rl) {
+ aggr_limit = ath_lookup_rate(sc, bf);
+ rl = 1;
+ /*
+ * Is rate dual stream
+ */
+ is_ds_rate =
+ (bf->bf_rcs[0].flags & ATH_RC_DS_FLAG) ? 1 : 0;
+ }
+
+ /*
+ * do not exceed aggregation limit
+ */
+ al_delta = ATH_AGGR_DELIM_SZ + bf->bf_frmlen;
+
+ if (nframes && (aggr_limit <
+ (al + bpad + al_delta + prev_al))) {
+ status = ATH_AGGR_LIMITED;
+ break;
+ }
+
+ /*
+ * do not exceed subframe limit
+ */
+ if ((nframes + *prev_frames) >=
+ min((int)h_baw, ATH_AMPDU_SUBFRAME_DEFAULT)) {
+ status = ATH_AGGR_LIMITED;
+ break;
+ }
+
+ /*
+ * add padding for previous frame to aggregation length
+ */
+ al += bpad + al_delta;
+
+ /*
+ * Get the delimiters needed to meet the MPDU
+ * density for this node.
+ */
+ ndelim = ath_compute_num_delims(sc, bf_first, bf->bf_frmlen);
+
+ bpad = PADBYTES(al_delta) + (ndelim << 2);
+
+ bf->bf_next = NULL;
+ bf->bf_lastfrm->bf_desc->ds_link = 0;
+
+ /*
+ * this packet is part of an aggregate
+ * - remove all descriptors belonging to this frame from
+ * software queue
+ * - add it to block ack window
+ * - set up descriptors for aggregation
+ */
+ list_cut_position(&bf_head, &tid->buf_q, &bf->bf_lastfrm->list);
+ ath_tx_addto_baw(sc, tid, bf);
+
+ list_for_each_entry(tbf, &bf_head, list) {
+ ath9k_hw_set11n_aggr_middle(sc->sc_ah,
+ tbf->bf_desc, ndelim);
+ }
+
+ /*
+ * link buffers of this frame to the aggregate
+ */
+ list_splice_tail_init(&bf_head, bf_q);
+ nframes++;
+
+ if (bf_prev) {
+ bf_prev->bf_next = bf;
+ bf_prev->bf_lastfrm->bf_desc->ds_link = bf->bf_daddr;
+ }
+ bf_prev = bf;
+
+#ifdef AGGR_NOSHORT
+ /*
+ * terminate aggregation on a small packet boundary
+ */
+ if (bf->bf_frmlen < ATH_AGGR_MINPLEN) {
+ status = ATH_AGGR_SHORTPKT;
+ break;
+ }
+#endif
+ } while (!list_empty(&tid->buf_q));
+
+ bf_first->bf_al = al;
+ bf_first->bf_nframes = nframes;
+ *bf_last = bf_prev;
+ return status;
+#undef PADBYTES
+}
+
+/*
+ * process pending frames possibly doing a-mpdu aggregation
+ * NB: must be called with txq lock held
+ */
+
+static void ath_tx_sched_aggr(struct ath_softc *sc,
+ struct ath_txq *txq, struct ath_atx_tid *tid)
+{
+ struct ath_buf *bf, *tbf, *bf_last, *bf_lastaggr = NULL;
+ enum ATH_AGGR_STATUS status;
+ struct list_head bf_q;
+ struct aggr_rifs_param param = {0, 0, 0, 0, NULL};
+ int prev_frames = 0;
+
+ do {
+ if (list_empty(&tid->buf_q))
+ return;
+
+ INIT_LIST_HEAD(&bf_q);
+
+ status = ath_tx_form_aggr(sc, tid, &bf_q, &bf_lastaggr, ¶m,
+ &prev_frames);
+
+ /*
+ * no frames picked up to be aggregated; block-ack
+ * window is not open
+ */
+ if (list_empty(&bf_q))
+ break;
+
+ bf = list_first_entry(&bf_q, struct ath_buf, list);
+ bf_last = list_entry(bf_q.prev, struct ath_buf, list);
+ bf->bf_lastbf = bf_last;
+
+ /*
+ * if only one frame, send as non-aggregate
+ */
+ if (bf->bf_nframes == 1) {
+ ASSERT(bf->bf_lastfrm == bf_last);
+
+ bf->bf_isaggr = 0;
+ /*
+ * clear aggr bits for every descriptor
+ * XXX TODO: is there a way to optimize it?
+ */
+ list_for_each_entry(tbf, &bf_q, list) {
+ ath9k_hw_clr11n_aggr(sc->sc_ah, tbf->bf_desc);
+ }
+
+ ath_buf_set_rate(sc, bf);
+ ath_tx_txqaddbuf(sc, txq, &bf_q);
+ continue;
+ }
+
+ /*
+ * setup first desc with rate and aggr info
+ */
+ bf->bf_isaggr = 1;
+ ath_buf_set_rate(sc, bf);
+ ath9k_hw_set11n_aggr_first(sc->sc_ah, bf->bf_desc, bf->bf_al);
+
+ /*
+ * anchor last frame of aggregate correctly
+ */
+ ASSERT(bf_lastaggr);
+ ASSERT(bf_lastaggr->bf_lastfrm == bf_last);
+ tbf = bf_lastaggr;
+ ath9k_hw_set11n_aggr_last(sc->sc_ah, tbf->bf_desc);
+
+ /* XXX: We don't enter into this loop, consider removing this */
+ while (!list_empty(&bf_q) && !list_is_last(&tbf->list, &bf_q)) {
+ tbf = list_entry(tbf->list.next, struct ath_buf, list);
+ ath9k_hw_set11n_aggr_last(sc->sc_ah, tbf->bf_desc);
+ }
+
+ txq->axq_aggr_depth++;
+
+ /*
+ * Normal aggregate, queue to hardware
+ */
+ ath_tx_txqaddbuf(sc, txq, &bf_q);
+
+ } while (txq->axq_depth < ATH_AGGR_MIN_QDEPTH &&
+ status != ATH_AGGR_BAW_CLOSED);
+}
+
+/* Called with txq lock held */
+
+static void ath_tid_drain(struct ath_softc *sc,
+ struct ath_txq *txq,
+ struct ath_atx_tid *tid,
+ bool bh_flag)
+{
+ struct ath_buf *bf;
+ struct list_head bf_head;
+ INIT_LIST_HEAD(&bf_head);
+
+ for (;;) {
+ if (list_empty(&tid->buf_q))
+ break;
+ bf = list_first_entry(&tid->buf_q, struct ath_buf, list);
+
+ list_cut_position(&bf_head, &tid->buf_q, &bf->bf_lastfrm->list);
+
+ /* update baw for software retried frame */
+ if (bf->bf_isretried)
+ ath_tx_update_baw(sc, tid, bf->bf_seqno);
+
+ /*
+ * do not indicate packets while holding txq spinlock.
+ * unlock is intentional here
+ */
+ if (likely(bh_flag))
+ spin_unlock_bh(&txq->axq_lock);
+ else
+ spin_unlock(&txq->axq_lock);
+
+ /* complete this sub-frame */
+ ath_tx_complete_buf(sc, bf, &bf_head, 0, 0);
+
+ if (likely(bh_flag))
+ spin_lock_bh(&txq->axq_lock);
+ else
+ spin_lock(&txq->axq_lock);
+ }
+
+ /*
+ * TODO: For frame(s) that are in the retry state, we will reuse the
+ * sequence number(s) without setting the retry bit. The
+ * alternative is to give up on these and BAR the receiver's window
+ * forward.
+ */
+ tid->seq_next = tid->seq_start;
+ tid->baw_tail = tid->baw_head;
+}
+
+/*
+ * Drain all pending buffers
+ * NB: must be called with txq lock held
+ */
+
+static void ath_txq_drain_pending_buffers(struct ath_softc *sc,
+ struct ath_txq *txq,
+ bool bh_flag)
+{
+ struct ath_atx_ac *ac, *ac_tmp;
+ struct ath_atx_tid *tid, *tid_tmp;
+
+ list_for_each_entry_safe(ac, ac_tmp, &txq->axq_acq, list) {
+ list_del(&ac->list);
+ ac->sched = false;
+ list_for_each_entry_safe(tid, tid_tmp, &ac->tid_q, list) {
+ list_del(&tid->list);
+ tid->sched = false;
+ ath_tid_drain(sc, txq, tid, bh_flag);
+ }
+ }
+}
+
+static int ath_tx_start_dma(struct ath_softc *sc,
+ struct sk_buff *skb,
+ struct scatterlist *sg,
+ u32 n_sg,
+ struct ath_tx_control *txctl)
+{
+ struct ath_node *an = txctl->an;
+ struct ath_buf *bf = NULL;
+ struct list_head bf_head;
+ struct ath_desc *ds;
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath_txq *txq = &sc->sc_txq[txctl->qnum];
+ struct ath_tx_info_priv *tx_info_priv;
+ struct ath_rc_series *rcs;
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ __le16 fc = hdr->frame_control;
+
+ /* For each sglist entry, allocate an ath_buf for DMA */
+ INIT_LIST_HEAD(&bf_head);
+ spin_lock_bh(&sc->sc_txbuflock);
+ if (unlikely(list_empty(&sc->sc_txbuf))) {
+ spin_unlock_bh(&sc->sc_txbuflock);
+ return -ENOMEM;
+ }
+
+ bf = list_first_entry(&sc->sc_txbuf, struct ath_buf, list);
+ list_del(&bf->list);
+ spin_unlock_bh(&sc->sc_txbuflock);
+
+ list_add_tail(&bf->list, &bf_head);
+
+ /* set up this buffer */
+ ATH_TXBUF_RESET(bf);
+ bf->bf_frmlen = txctl->frmlen;
+ bf->bf_isdata = ieee80211_is_data(fc);
+ bf->bf_isbar = ieee80211_is_back_req(fc);
+ bf->bf_ispspoll = ieee80211_is_pspoll(fc);
+ bf->bf_flags = txctl->flags;
+ bf->bf_shpreamble = sc->sc_flags & ATH_PREAMBLE_SHORT;
+ bf->bf_keytype = txctl->keytype;
+ tx_info_priv = (struct ath_tx_info_priv *)tx_info->driver_data[0];
+ rcs = tx_info_priv->rcs;
+ bf->bf_rcs[0] = rcs[0];
+ bf->bf_rcs[1] = rcs[1];
+ bf->bf_rcs[2] = rcs[2];
+ bf->bf_rcs[3] = rcs[3];
+ bf->bf_node = an;
+ bf->bf_mpdu = skb;
+ bf->bf_buf_addr = sg_dma_address(sg);
+
+ /* setup descriptor */
+ ds = bf->bf_desc;
+ ds->ds_link = 0;
+ ds->ds_data = bf->bf_buf_addr;
+
+ /*
+ * Save the DMA context in the first ath_buf
+ */
+ copy_dma_mem_context(get_dma_mem_context(bf, bf_dmacontext),
+ get_dma_mem_context(txctl, dmacontext));
+
+ /*
+ * Formulate first tx descriptor with tx controls.
+ */
+ ath9k_hw_set11n_txdesc(ah,
+ ds,
+ bf->bf_frmlen, /* frame length */
+ txctl->atype, /* Atheros packet type */
+ min(txctl->txpower, (u16)60), /* txpower */
+ txctl->keyix, /* key cache index */
+ txctl->keytype, /* key type */
+ txctl->flags); /* flags */
+ ath9k_hw_filltxdesc(ah,
+ ds,
+ sg_dma_len(sg), /* segment length */
+ true, /* first segment */
+ (n_sg == 1) ? true : false, /* last segment */
+ ds); /* first descriptor */
+
+ bf->bf_lastfrm = bf;
+ bf->bf_ht = txctl->ht;
+
+ spin_lock_bh(&txq->axq_lock);
+
+ if (txctl->ht && sc->sc_txaggr) {
+ struct ath_atx_tid *tid = ATH_AN_2_TID(an, txctl->tidno);
+ if (ath_aggr_query(sc, an, txctl->tidno)) {
+ /*
+ * Try aggregation if it's a unicast data frame
+ * and the destination is HT capable.
+ */
+ ath_tx_send_ampdu(sc, txq, tid, &bf_head, txctl);
+ } else {
+ /*
+ * Send this frame as regular when ADDBA exchange
+ * is neither complete nor pending.
+ */
+ ath_tx_send_normal(sc, txq, tid, &bf_head);
+ }
+ } else {
+ bf->bf_lastbf = bf;
+ bf->bf_nframes = 1;
+ ath_buf_set_rate(sc, bf);
+
+ if (ieee80211_is_back_req(fc)) {
+ /* This is required for resuming tid
+ * during BAR completion */
+ bf->bf_tidno = txctl->tidno;
+ }
+
+ if (is_multicast_ether_addr(hdr->addr1)) {
+ struct ath_vap *avp = sc->sc_vaps[txctl->if_id];
+
+ /*
+ * When servicing one or more stations in power-save
+ * mode (or) if there is some mcast data waiting on
+ * mcast queue (to prevent out of order delivery of
+ * mcast,bcast packets) multicast frames must be
+ * buffered until after the beacon. We use the private
+ * mcast queue for that.
+ */
+ /* XXX? more bit in 802.11 frame header */
+ spin_lock_bh(&avp->av_mcastq.axq_lock);
+ if (txctl->ps || avp->av_mcastq.axq_depth)
+ ath_tx_mcastqaddbuf(sc,
+ &avp->av_mcastq, &bf_head);
+ else
+ ath_tx_txqaddbuf(sc, txq, &bf_head);
+ spin_unlock_bh(&avp->av_mcastq.axq_lock);
+ } else
+ ath_tx_txqaddbuf(sc, txq, &bf_head);
+ }
+ spin_unlock_bh(&txq->axq_lock);
+ return 0;
+}
+
+static void xmit_map_sg(struct ath_softc *sc,
+ struct sk_buff *skb,
+ dma_addr_t *pa,
+ struct ath_tx_control *txctl)
+{
+ struct ath_xmit_status tx_status;
+ struct ath_atx_tid *tid;
+ struct scatterlist sg;
+
+ *pa = pci_map_single(sc->pdev, skb->data, skb->len, PCI_DMA_TODEVICE);
+
+ /* setup S/G list */
+ memset(&sg, 0, sizeof(struct scatterlist));
+ sg_dma_address(&sg) = *pa;
+ sg_dma_len(&sg) = skb->len;
+
+ if (ath_tx_start_dma(sc, skb, &sg, 1, txctl) != 0) {
+ /*
+ * We have to do drop frame here.
+ */
+ pci_unmap_single(sc->pdev, *pa, skb->len, PCI_DMA_TODEVICE);
+
+ tx_status.retries = 0;
+ tx_status.flags = ATH_TX_ERROR;
+
+ if (txctl->ht && sc->sc_txaggr) {
+ /* Reclaim the seqno. */
+ tid = ATH_AN_2_TID((struct ath_node *)
+ txctl->an, txctl->tidno);
+ DECR(tid->seq_next, IEEE80211_SEQ_MAX);
+ }
+ ath_tx_complete(sc, skb, &tx_status, txctl->an);
+ }
+}
+
+/* Initialize TX queue and h/w */
+
+int ath_tx_init(struct ath_softc *sc, int nbufs)
+{
+ int error = 0;
+
+ do {
+ spin_lock_init(&sc->sc_txbuflock);
+
+ /* Setup tx descriptors */
+ error = ath_descdma_setup(sc, &sc->sc_txdma, &sc->sc_txbuf,
+ "tx", nbufs * ATH_FRAG_PER_MSDU, ATH_TXDESC);
+ if (error != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: failed to allocate tx descriptors: %d\n",
+ __func__, error);
+ break;
+ }
+
+ /* XXX allocate beacon state together with vap */
+ error = ath_descdma_setup(sc, &sc->sc_bdma, &sc->sc_bbuf,
+ "beacon", ATH_BCBUF, 1);
+ if (error != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: failed to allocate "
+ "beacon descripotrs: %d\n",
+ __func__, error);
+ break;
+ }
+
+ } while (0);
+
+ if (error != 0)
+ ath_tx_cleanup(sc);
+
+ return error;
+}
+
+/* Reclaim all tx queue resources */
+
+int ath_tx_cleanup(struct ath_softc *sc)
+{
+ /* cleanup beacon descriptors */
+ if (sc->sc_bdma.dd_desc_len != 0)
+ ath_descdma_cleanup(sc, &sc->sc_bdma, &sc->sc_bbuf);
+
+ /* cleanup tx descriptors */
+ if (sc->sc_txdma.dd_desc_len != 0)
+ ath_descdma_cleanup(sc, &sc->sc_txdma, &sc->sc_txbuf);
+
+ return 0;
+}
+
+/* Setup a h/w transmit queue */
+
+struct ath_txq *ath_txq_setup(struct ath_softc *sc, int qtype, int subtype)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ struct ath9k_tx_queue_info qi;
+ int qnum;
+
+ memzero(&qi, sizeof(qi));
+ qi.tqi_subtype = subtype;
+ qi.tqi_aifs = ATH9K_TXQ_USEDEFAULT;
+ qi.tqi_cwmin = ATH9K_TXQ_USEDEFAULT;
+ qi.tqi_cwmax = ATH9K_TXQ_USEDEFAULT;
+ qi.tqi_physCompBuf = 0;
+
+ /*
+ * Enable interrupts only for EOL and DESC conditions.
+ * We mark tx descriptors to receive a DESC interrupt
+ * when a tx queue gets deep; otherwise waiting for the
+ * EOL to reap descriptors. Note that this is done to
+ * reduce interrupt load and this only defers reaping
+ * descriptors, never transmitting frames. Aside from
+ * reducing interrupts this also permits more concurrency.
+ * The only potential downside is if the tx queue backs
+ * up in which case the top half of the kernel may backup
+ * due to a lack of tx descriptors.
+ *
+ * The UAPSD queue is an exception, since we take a desc-
+ * based intr on the EOSP frames.
+ */
+ if (qtype == ATH9K_TX_QUEUE_UAPSD)
+ qi.tqi_qflags = TXQ_FLAG_TXDESCINT_ENABLE;
+ else
+ qi.tqi_qflags = TXQ_FLAG_TXEOLINT_ENABLE |
+ TXQ_FLAG_TXDESCINT_ENABLE;
+ qnum = ath9k_hw_setuptxqueue(ah, qtype, &qi);
+ if (qnum == -1) {
+ /*
+ * NB: don't print a message, this happens
+ * normally on parts with too few tx queues
+ */
+ return NULL;
+ }
+ if (qnum >= ARRAY_SIZE(sc->sc_txq)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: hal qnum %u out of range, max %u!\n",
+ __func__, qnum, (unsigned int)ARRAY_SIZE(sc->sc_txq));
+ ath9k_hw_releasetxqueue(ah, qnum);
+ return NULL;
+ }
+ if (!ATH_TXQ_SETUP(sc, qnum)) {
+ struct ath_txq *txq = &sc->sc_txq[qnum];
+
+ txq->axq_qnum = qnum;
+ txq->axq_link = NULL;
+ INIT_LIST_HEAD(&txq->axq_q);
+ INIT_LIST_HEAD(&txq->axq_acq);
+ spin_lock_init(&txq->axq_lock);
+ txq->axq_depth = 0;
+ txq->axq_aggr_depth = 0;
+ txq->axq_totalqueued = 0;
+ txq->axq_intrcnt = 0;
+ txq->axq_linkbuf = NULL;
+ sc->sc_txqsetup |= 1<<qnum;
+ }
+ return &sc->sc_txq[qnum];
+}
+
+/* Reclaim resources for a setup queue */
+
+void ath_tx_cleanupq(struct ath_softc *sc, struct ath_txq *txq)
+{
+ ath9k_hw_releasetxqueue(sc->sc_ah, txq->axq_qnum);
+ sc->sc_txqsetup &= ~(1<<txq->axq_qnum);
+}
+
+/*
+ * Setup a hardware data transmit queue for the specified
+ * access control. The hal may not support all requested
+ * queues in which case it will return a reference to a
+ * previously setup queue. We record the mapping from ac's
+ * to h/w queues for use by ath_tx_start and also track
+ * the set of h/w queues being used to optimize work in the
+ * transmit interrupt handler and related routines.
+ */
+
+int ath_tx_setup(struct ath_softc *sc, int haltype)
+{
+ struct ath_txq *txq;
+
+ if (haltype >= ARRAY_SIZE(sc->sc_haltype2q)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: HAL AC %u out of range, max %zu!\n",
+ __func__, haltype, ARRAY_SIZE(sc->sc_haltype2q));
+ return 0;
+ }
+ txq = ath_txq_setup(sc, ATH9K_TX_QUEUE_DATA, haltype);
+ if (txq != NULL) {
+ sc->sc_haltype2q[haltype] = txq->axq_qnum;
+ return 1;
+ } else
+ return 0;
+}
+
+int ath_tx_get_qnum(struct ath_softc *sc, int qtype, int haltype)
+{
+ int qnum;
+
+ switch (qtype) {
+ case ATH9K_TX_QUEUE_DATA:
+ if (haltype >= ARRAY_SIZE(sc->sc_haltype2q)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: HAL AC %u out of range, max %zu!\n",
+ __func__,
+ haltype, ARRAY_SIZE(sc->sc_haltype2q));
+ return -1;
+ }
+ qnum = sc->sc_haltype2q[haltype];
+ break;
+ case ATH9K_TX_QUEUE_BEACON:
+ qnum = sc->sc_bhalq;
+ break;
+ case ATH9K_TX_QUEUE_CAB:
+ qnum = sc->sc_cabq->axq_qnum;
+ break;
+ default:
+ qnum = -1;
+ }
+ return qnum;
+}
+
+/* Update parameters for a transmit queue */
+
+int ath_txq_update(struct ath_softc *sc, int qnum,
+ struct ath9k_tx_queue_info *qinfo)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int error = 0;
+ struct ath9k_tx_queue_info qi;
+
+ if (qnum == sc->sc_bhalq) {
+ /*
+ * XXX: for beacon queue, we just save the parameter.
+ * It will be picked up by ath_beaconq_config when
+ * it's necessary.
+ */
+ sc->sc_beacon_qi = *qinfo;
+ return 0;
+ }
+
+ ASSERT(sc->sc_txq[qnum].axq_qnum == qnum);
+
+ ath9k_hw_get_txq_props(ah, qnum, &qi);
+ qi.tqi_aifs = qinfo->tqi_aifs;
+ qi.tqi_cwmin = qinfo->tqi_cwmin;
+ qi.tqi_cwmax = qinfo->tqi_cwmax;
+ qi.tqi_burstTime = qinfo->tqi_burstTime;
+ qi.tqi_readyTime = qinfo->tqi_readyTime;
+
+ if (!ath9k_hw_set_txq_props(ah, qnum, &qi)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to update hardware queue %u!\n",
+ __func__, qnum);
+ error = -EIO;
+ } else {
+ ath9k_hw_resettxqueue(ah, qnum); /* push to h/w */
+ }
+
+ return error;
+}
+
+int ath_cabq_update(struct ath_softc *sc)
+{
+ struct ath9k_tx_queue_info qi;
+ int qnum = sc->sc_cabq->axq_qnum;
+ struct ath_beacon_config conf;
+
+ ath9k_hw_get_txq_props(sc->sc_ah, qnum, &qi);
+ /*
+ * Ensure the readytime % is within the bounds.
+ */
+ if (sc->sc_config.cabqReadytime < ATH9K_READY_TIME_LO_BOUND)
+ sc->sc_config.cabqReadytime = ATH9K_READY_TIME_LO_BOUND;
+ else if (sc->sc_config.cabqReadytime > ATH9K_READY_TIME_HI_BOUND)
+ sc->sc_config.cabqReadytime = ATH9K_READY_TIME_HI_BOUND;
+
+ ath_get_beaconconfig(sc, ATH_IF_ID_ANY, &conf);
+ qi.tqi_readyTime =
+ (conf.beacon_interval * sc->sc_config.cabqReadytime) / 100;
+ ath_txq_update(sc, qnum, &qi);
+
+ return 0;
+}
+
+int ath_tx_start(struct ath_softc *sc, struct sk_buff *skb)
+{
+ struct ath_tx_control txctl;
+ int error = 0;
+
+ error = ath_tx_prepare(sc, skb, &txctl);
+ if (error == 0)
+ /*
+ * Start DMA mapping.
+ * ath_tx_start_dma() will be called either synchronously
+ * or asynchrounsly once DMA is complete.
+ */
+ xmit_map_sg(sc, skb,
+ get_dma_mem_context(&txctl, dmacontext),
+ &txctl);
+ else
+ ath_node_put(sc, txctl.an, ATH9K_BH_STATUS_CHANGE);
+
+ /* failed packets will be dropped by the caller */
+ return error;
+}
+
+/* Deferred processing of transmit interrupt */
+
+void ath_tx_tasklet(struct ath_softc *sc)
+{
+ u64 tsf = ath9k_hw_gettsf64(sc->sc_ah);
+ int i, nacked = 0;
+ u32 qcumask = ((1 << ATH9K_NUM_TX_QUEUES) - 1);
+
+ ath9k_hw_gettxintrtxqs(sc->sc_ah, &qcumask);
+
+ /*
+ * Process each active queue.
+ */
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i) && (qcumask & (1 << i)))
+ nacked += ath_tx_processq(sc, &sc->sc_txq[i]);
+ }
+ if (nacked)
+ sc->sc_lastrx = tsf;
+}
+
+void ath_tx_draintxq(struct ath_softc *sc,
+ struct ath_txq *txq, bool retry_tx)
+{
+ struct ath_buf *bf, *lastbf;
+ struct list_head bf_head;
+
+ INIT_LIST_HEAD(&bf_head);
+
+ /*
+ * NB: this assumes output has been stopped and
+ * we do not need to block ath_tx_tasklet
+ */
+ for (;;) {
+ spin_lock_bh(&txq->axq_lock);
+
+ if (list_empty(&txq->axq_q)) {
+ txq->axq_link = NULL;
+ txq->axq_linkbuf = NULL;
+ spin_unlock_bh(&txq->axq_lock);
+ break;
+ }
+
+ bf = list_first_entry(&txq->axq_q, struct ath_buf, list);
+
+ if (bf->bf_status & ATH_BUFSTATUS_STALE) {
+ list_del(&bf->list);
+ spin_unlock_bh(&txq->axq_lock);
+
+ spin_lock_bh(&sc->sc_txbuflock);
+ list_add_tail(&bf->list, &sc->sc_txbuf);
+ spin_unlock_bh(&sc->sc_txbuflock);
+ continue;
+ }
+
+ lastbf = bf->bf_lastbf;
+ if (!retry_tx)
+ lastbf->bf_desc->ds_txstat.ts_flags =
+ ATH9K_TX_SW_ABORTED;
+
+ /* remove ath_buf's of the same mpdu from txq */
+ list_cut_position(&bf_head, &txq->axq_q, &lastbf->list);
+ txq->axq_depth--;
+
+ spin_unlock_bh(&txq->axq_lock);
+
+ if (bf->bf_isampdu)
+ ath_tx_complete_aggr_rifs(sc, txq, bf, &bf_head, 0);
+ else
+ ath_tx_complete_buf(sc, bf, &bf_head, 0, 0);
+ }
+
+ /* flush any pending frames if aggregation is enabled */
+ if (sc->sc_txaggr) {
+ if (!retry_tx) {
+ spin_lock_bh(&txq->axq_lock);
+ ath_txq_drain_pending_buffers(sc, txq,
+ ATH9K_BH_STATUS_CHANGE);
+ spin_unlock_bh(&txq->axq_lock);
+ }
+ }
+}
+
+/* Drain the transmit queues and reclaim resources */
+
+void ath_draintxq(struct ath_softc *sc, bool retry_tx)
+{
+ /* stop beacon queue. The beacon will be freed when
+ * we go to INIT state */
+ if (!sc->sc_invalid) {
+ (void) ath9k_hw_stoptxdma(sc->sc_ah, sc->sc_bhalq);
+ DPRINTF(sc, ATH_DBG_XMIT, "%s: beacon queue %x\n", __func__,
+ ath9k_hw_gettxbuf(sc->sc_ah, sc->sc_bhalq));
+ }
+
+ ath_drain_txdataq(sc, retry_tx);
+}
+
+u32 ath_txq_depth(struct ath_softc *sc, int qnum)
+{
+ return sc->sc_txq[qnum].axq_depth;
+}
+
+u32 ath_txq_aggr_depth(struct ath_softc *sc, int qnum)
+{
+ return sc->sc_txq[qnum].axq_aggr_depth;
+}
+
+/* Check if an ADDBA is required. A valid node must be passed. */
+enum ATH_AGGR_CHECK ath_tx_aggr_check(struct ath_softc *sc,
+ struct ath_node *an,
+ u8 tidno)
+{
+ struct ath_atx_tid *txtid;
+ DECLARE_MAC_BUF(mac);
+
+ if (!sc->sc_txaggr)
+ return AGGR_NOT_REQUIRED;
+
+ /* ADDBA exchange must be completed before sending aggregates */
+ txtid = ATH_AN_2_TID(an, tidno);
+
+ if (txtid->addba_exchangecomplete)
+ return AGGR_EXCHANGE_DONE;
+
+ if (txtid->cleanup_inprogress)
+ return AGGR_CLEANUP_PROGRESS;
+
+ if (txtid->addba_exchangeinprogress)
+ return AGGR_EXCHANGE_PROGRESS;
+
+ if (!txtid->addba_exchangecomplete) {
+ if (!txtid->addba_exchangeinprogress &&
+ (txtid->addba_exchangeattempts < ADDBA_EXCHANGE_ATTEMPTS)) {
+ txtid->addba_exchangeattempts++;
+ return AGGR_REQUIRED;
+ }
+ }
+
+ return AGGR_NOT_REQUIRED;
+}
+
+/* Start TX aggregation */
+
+int ath_tx_aggr_start(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid,
+ u16 *ssn)
+{
+ struct ath_atx_tid *txtid;
+ struct ath_node *an;
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, (u8 *) addr);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (!an) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: Node not found to initialize "
+ "TX aggregation\n", __func__);
+ return -1;
+ }
+
+ if (sc->sc_txaggr) {
+ txtid = ATH_AN_2_TID(an, tid);
+ txtid->addba_exchangeinprogress = 1;
+ ath_tx_pause_tid(sc, txtid);
+ }
+
+ return 0;
+}
+
+/* Stop tx aggregation */
+
+int ath_tx_aggr_stop(struct ath_softc *sc,
+ const u8 *addr,
+ u16 tid)
+{
+ struct ath_node *an;
+
+ spin_lock_bh(&sc->node_lock);
+ an = ath_node_find(sc, (u8 *) addr);
+ spin_unlock_bh(&sc->node_lock);
+
+ if (!an) {
+ DPRINTF(sc, ATH_DBG_AGGR,
+ "%s: TX aggr stop for non-existent node\n", __func__);
+ return -1;
+ }
+
+ ath_tx_aggr_teardown(sc, an, tid);
+ return 0;
+}
+
+/*
+ * Performs transmit side cleanup when TID changes from aggregated to
+ * unaggregated.
+ * - Pause the TID and mark cleanup in progress
+ * - Discard all retry frames from the s/w queue.
+ */
+
+void ath_tx_aggr_teardown(struct ath_softc *sc,
+ struct ath_node *an, u8 tid)
+{
+ struct ath_atx_tid *txtid = ATH_AN_2_TID(an, tid);
+ struct ath_txq *txq = &sc->sc_txq[txtid->ac->qnum];
+ struct ath_buf *bf;
+ struct list_head bf_head;
+ INIT_LIST_HEAD(&bf_head);
+
+ DPRINTF(sc, ATH_DBG_AGGR, "%s: teardown TX aggregation\n", __func__);
+
+ if (txtid->cleanup_inprogress) /* cleanup is in progress */
+ return;
+
+ if (!txtid->addba_exchangecomplete) {
+ txtid->addba_exchangeattempts = 0;
+ return;
+ }
+
+ /* TID must be paused first */
+ ath_tx_pause_tid(sc, txtid);
+
+ /* drop all software retried frames and mark this TID */
+ spin_lock_bh(&txq->axq_lock);
+ while (!list_empty(&txtid->buf_q)) {
+ bf = list_first_entry(&txtid->buf_q, struct ath_buf, list);
+ if (!bf->bf_isretried) {
+ /*
+ * NB: it's based on the assumption that
+ * software retried frame will always stay
+ * at the head of software queue.
+ */
+ break;
+ }
+ list_cut_position(&bf_head,
+ &txtid->buf_q, &bf->bf_lastfrm->list);
+ ath_tx_update_baw(sc, txtid, bf->bf_seqno);
+
+ /* complete this sub-frame */
+ ath_tx_complete_buf(sc, bf, &bf_head, 0, 0);
+ }
+
+ if (txtid->baw_head != txtid->baw_tail) {
+ spin_unlock_bh(&txq->axq_lock);
+ txtid->cleanup_inprogress = true;
+ } else {
+ txtid->addba_exchangecomplete = 0;
+ txtid->addba_exchangeattempts = 0;
+ spin_unlock_bh(&txq->axq_lock);
+ ath_tx_flush_tid(sc, txtid);
+ }
+}
+
+/*
+ * Tx scheduling logic
+ * NB: must be called with txq lock held
+ */
+
+void ath_txq_schedule(struct ath_softc *sc, struct ath_txq *txq)
+{
+ struct ath_atx_ac *ac;
+ struct ath_atx_tid *tid;
+
+ /* nothing to schedule */
+ if (list_empty(&txq->axq_acq))
+ return;
+ /*
+ * get the first node/ac pair on the queue
+ */
+ ac = list_first_entry(&txq->axq_acq, struct ath_atx_ac, list);
+ list_del(&ac->list);
+ ac->sched = false;
+
+ /*
+ * process a single tid per destination
+ */
+ do {
+ /* nothing to schedule */
+ if (list_empty(&ac->tid_q))
+ return;
+
+ tid = list_first_entry(&ac->tid_q, struct ath_atx_tid, list);
+ list_del(&tid->list);
+ tid->sched = false;
+
+ if (tid->paused) /* check next tid to keep h/w busy */
+ continue;
+
+ if (!(tid->an->an_smmode == ATH_SM_PWRSAV_DYNAMIC) ||
+ ((txq->axq_depth % 2) == 0)) {
+ ath_tx_sched_aggr(sc, txq, tid);
+ }
+
+ /*
+ * add tid to round-robin queue if more frames
+ * are pending for the tid
+ */
+ if (!list_empty(&tid->buf_q))
+ ath_tx_queue_tid(txq, tid);
+
+ /* only schedule one TID at a time */
+ break;
+ } while (!list_empty(&ac->tid_q));
+
+ /*
+ * schedule AC if more TIDs need processing
+ */
+ if (!list_empty(&ac->tid_q)) {
+ /*
+ * add dest ac to txq if not already added
+ */
+ if (!ac->sched) {
+ ac->sched = true;
+ list_add_tail(&ac->list, &txq->axq_acq);
+ }
+ }
+}
+
+/* Initialize per-node transmit state */
+
+void ath_tx_node_init(struct ath_softc *sc, struct ath_node *an)
+{
+ if (sc->sc_txaggr) {
+ struct ath_atx_tid *tid;
+ struct ath_atx_ac *ac;
+ int tidno, acno;
+
+ sc->sc_ht_info.maxampdu = ATH_AMPDU_LIMIT_DEFAULT;
+
+ /*
+ * Init per tid tx state
+ */
+ for (tidno = 0, tid = &an->an_aggr.tx.tid[tidno];
+ tidno < WME_NUM_TID;
+ tidno++, tid++) {
+ tid->an = an;
+ tid->tidno = tidno;
+ tid->seq_start = tid->seq_next = 0;
+ tid->baw_size = WME_MAX_BA;
+ tid->baw_head = tid->baw_tail = 0;
+ tid->sched = false;
+ tid->paused = false;
+ tid->cleanup_inprogress = false;
+ INIT_LIST_HEAD(&tid->buf_q);
+
+ acno = TID_TO_WME_AC(tidno);
+ tid->ac = &an->an_aggr.tx.ac[acno];
+
+ /* ADDBA state */
+ tid->addba_exchangecomplete = 0;
+ tid->addba_exchangeinprogress = 0;
+ tid->addba_exchangeattempts = 0;
+ }
+
+ /*
+ * Init per ac tx state
+ */
+ for (acno = 0, ac = &an->an_aggr.tx.ac[acno];
+ acno < WME_NUM_AC; acno++, ac++) {
+ ac->sched = false;
+ INIT_LIST_HEAD(&ac->tid_q);
+
+ switch (acno) {
+ case WME_AC_BE:
+ ac->qnum = ath_tx_get_qnum(sc,
+ ATH9K_TX_QUEUE_DATA, ATH9K_WME_AC_BE);
+ break;
+ case WME_AC_BK:
+ ac->qnum = ath_tx_get_qnum(sc,
+ ATH9K_TX_QUEUE_DATA, ATH9K_WME_AC_BK);
+ break;
+ case WME_AC_VI:
+ ac->qnum = ath_tx_get_qnum(sc,
+ ATH9K_TX_QUEUE_DATA, ATH9K_WME_AC_VI);
+ break;
+ case WME_AC_VO:
+ ac->qnum = ath_tx_get_qnum(sc,
+ ATH9K_TX_QUEUE_DATA, ATH9K_WME_AC_VO);
+ break;
+ }
+ }
+ }
+}
+
+/* Cleanupthe pending buffers for the node. */
+
+void ath_tx_node_cleanup(struct ath_softc *sc,
+ struct ath_node *an, bool bh_flag)
+{
+ int i;
+ struct ath_atx_ac *ac, *ac_tmp;
+ struct ath_atx_tid *tid, *tid_tmp;
+ struct ath_txq *txq;
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i)) {
+ txq = &sc->sc_txq[i];
+
+ if (likely(bh_flag))
+ spin_lock_bh(&txq->axq_lock);
+ else
+ spin_lock(&txq->axq_lock);
+
+ list_for_each_entry_safe(ac,
+ ac_tmp, &txq->axq_acq, list) {
+ tid = list_first_entry(&ac->tid_q,
+ struct ath_atx_tid, list);
+ if (tid && tid->an != an)
+ continue;
+ list_del(&ac->list);
+ ac->sched = false;
+
+ list_for_each_entry_safe(tid,
+ tid_tmp, &ac->tid_q, list) {
+ list_del(&tid->list);
+ tid->sched = false;
+ ath_tid_drain(sc, txq, tid, bh_flag);
+ tid->addba_exchangecomplete = 0;
+ tid->addba_exchangeattempts = 0;
+ tid->cleanup_inprogress = false;
+ }
+ }
+
+ if (likely(bh_flag))
+ spin_unlock_bh(&txq->axq_lock);
+ else
+ spin_unlock(&txq->axq_lock);
+ }
+ }
+}
+
+/* Cleanup per node transmit state */
+
+void ath_tx_node_free(struct ath_softc *sc, struct ath_node *an)
+{
+ if (sc->sc_txaggr) {
+ struct ath_atx_tid *tid;
+ int tidno, i;
+
+ /* Init per tid rx state */
+ for (tidno = 0, tid = &an->an_aggr.tx.tid[tidno];
+ tidno < WME_NUM_TID;
+ tidno++, tid++) {
+
+ for (i = 0; i < ATH_TID_MAX_BUFS; i++)
+ ASSERT(tid->tx_buf[i] == NULL);
+ }
+ }
+}
}
/* fill hw info */
- hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
- IEEE80211_HW_RX_INCLUDES_FCS |
+ hw->flags = IEEE80211_HW_RX_INCLUDES_FCS |
IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM;
const struct b43_phy *phy = &dev->phy;
const struct ieee80211_hdr *wlhdr =
(const struct ieee80211_hdr *)fragment_data;
- int use_encryption = (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT));
+ int use_encryption = !!info->control.hw_key;
__le16 fctl = wlhdr->frame_control;
struct ieee80211_rate *fbrate;
u8 rate, rate_fb;
}
/* fill hw info */
- hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
- IEEE80211_HW_RX_INCLUDES_FCS |
+ hw->flags = IEEE80211_HW_RX_INCLUDES_FCS |
IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM;
hw->queues = 1; /* FIXME: hardware has more queues */
goto out;
}
}
- mutex_unlock(&wl->mutex);
b43legacydbg(wl, "Device resumed.\n");
out:
+ mutex_unlock(&wl->mutex);
return err;
}
u16 cookie)
{
const struct ieee80211_hdr *wlhdr;
- int use_encryption = (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT));
+ int use_encryption = !!info->control.hw_key;
u16 fctl;
u8 rate;
struct ieee80211_rate *rate_fb;
if (err) {
printk(KERN_ERR "%s: pci_enable_device failed on resume\n",
dev->name);
+ mutex_unlock(&priv->action_mutex);
return err;
}
pci_restore_state(pci_dev);
err = ipw2100_get_ordinal(priv, IPW_ORD_CURRENT_TX_RATE, &val, &len);
if (err) {
IPW_DEBUG_WX("failed querying ordinals.\n");
- return err;
+ goto done;
}
switch (val & TX_RATE_MASK) {
#define _ipw_write8(ipw, ofs, val) writeb((val), (ipw)->hw_base + (ofs))
/* 8-bit direct write (for low 4K of SRAM/regs), with debug wrapper */
-#define ipw_write8(ipw, ofs, val) \
+#define ipw_write8(ipw, ofs, val) do { \
IPW_DEBUG_IO("%s %d: write_direct8(0x%08X, 0x%08X)\n", __FILE__, __LINE__, (u32)(ofs), (u32)(val)); \
- _ipw_write8(ipw, ofs, val)
+ _ipw_write8(ipw, ofs, val); \
+ } while (0)
/* 16-bit direct write (low 4K) */
#define _ipw_write16(ipw, ofs, val) writew((val), (ipw)->hw_base + (ofs))
MODULE_PARM_DESC(auto_create, "auto create adhoc network (default on)");
module_param(led, int, 0444);
-MODULE_PARM_DESC(led, "enable led control on some systems (default 0 off)\n");
+MODULE_PARM_DESC(led, "enable led control on some systems (default 0 off)");
module_param(debug, int, 0444);
MODULE_PARM_DESC(debug, "debug output mask");
default n
config IWLWIFI_RFKILL
- boolean "IWLWIFI RF kill support"
+ boolean "Iwlwifi RF kill support"
depends on IWLCORE
-config IWL4965
- tristate "Intel Wireless WiFi 4965AGN"
+config IWLWIFI_DEBUG
+ bool "Enable full debugging output in iwlagn driver"
+ depends on IWLCORE
+ ---help---
+ This option will enable debug tracing output for the iwlwifi drivers
+
+ This will result in the kernel module being ~100k larger. You can
+ control which debug output is sent to the kernel log by setting the
+ value in
+
+ /sys/class/net/wlan0/device/debug_level
+
+ This entry will only exist if this option is enabled.
+
+ To set a value, simply echo an 8-byte hex value to the same file:
+
+ % echo 0x43fff > /sys/class/net/wlan0/device/debug_level
+
+ You can find the list of debug mask values in:
+ drivers/net/wireless/iwlwifi/iwl-debug.h
+
+ If this is your first time using this driver, you should say Y here
+ as the debug information can assist others in helping you resolve
+ any problems you may encounter.
+
+config IWLWIFI_DEBUGFS
+ bool "Iwlwifi debugfs support"
+ depends on IWLCORE && IWLWIFI_DEBUG && MAC80211_DEBUGFS
+ ---help---
+ Enable creation of debugfs files for the iwlwifi drivers.
+
+config IWLAGN
+ tristate "Intel Wireless WiFi Next Gen AGN"
depends on PCI && MAC80211 && WLAN_80211 && EXPERIMENTAL
select FW_LOADER
select IWLCORE
---help---
Select to build the driver supporting the:
- Intel Wireless WiFi Link 4965AGN
+ Intel Wireless WiFi Link Next-Gen AGN
This driver uses the kernel's mac80211 subsystem.
If you want to compile the driver as a module ( = code which can be
inserted in and removed from the running kernel whenever you want),
say M here and read <file:Documentation/kbuild/modules.txt>. The
- module will be called iwl4965.ko.
-
-config IWL4965_LEDS
- bool "Enable LEDS features in iwl4965 driver"
- depends on IWL4965
- select IWLWIFI_LEDS
- ---help---
- This option enables LEDS for the iwlwifi drivers
+ module will be called iwlagn.ko.
-
-config IWL4965_SPECTRUM_MEASUREMENT
- bool "Enable Spectrum Measurement in iwl4965 driver"
- depends on IWL4965
+config IWLAGN_SPECTRUM_MEASUREMENT
+ bool "Enable Spectrum Measurement in iwlagn driver"
+ depends on IWLAGN
---help---
- This option will enable spectrum measurement for the iwl4965 driver.
+ This option will enable spectrum measurement for the iwlagn driver.
-config IWLWIFI_DEBUG
- bool "Enable full debugging output in iwl4965 driver"
- depends on IWL4965
+config IWLAGN_LEDS
+ bool "Enable LEDS features in iwlagn driver"
+ depends on IWLAGN
+ select IWLWIFI_LEDS
---help---
- This option will enable debug tracing output for the iwl4965
- driver.
-
- This will result in the kernel module being ~100k larger. You can
- control which debug output is sent to the kernel log by setting the
- value in
-
- /sys/class/net/wlan0/device/debug_level
-
- This entry will only exist if this option is enabled.
-
- To set a value, simply echo an 8-byte hex value to the same file:
-
- % echo 0x43fff > /sys/class/net/wlan0/device/debug_level
+ This option enables LEDS for the iwlagn drivers
- You can find the list of debug mask values in:
- drivers/net/wireless/iwlwifi/iwl-4965-debug.h
- If this is your first time using this driver, you should say Y here
- as the debug information can assist others in helping you resolve
- any problems you may encounter.
+config IWL4965
+ bool "Intel Wireless WiFi 4965AGN"
+ depends on IWLAGN
+ ---help---
+ This option enables support for Intel Wireless WiFi Link 4965AGN
config IWL5000
bool "Intel Wireless WiFi 5000AGN"
- depends on IWL4965
+ depends on IWLAGN
---help---
This option enables support for Intel Wireless WiFi Link 5000AGN Family
- Dependency on 4965 is temporary
-
-config IWLWIFI_DEBUGFS
- bool "Iwlwifi debugfs support"
- depends on IWLCORE && IWLWIFI_DEBUG && MAC80211_DEBUGFS
- ---help---
- Enable creation of debugfs files for the iwlwifi drivers.
config IWL3945
tristate "Intel PRO/Wireless 3945ABG/BG Network Connection"
iwlcore-$(CONFIG_IWLWIFI_LEDS) += iwl-led.o
iwlcore-$(CONFIG_IWLWIFI_RFKILL) += iwl-rfkill.o
+obj-$(CONFIG_IWLAGN) += iwlagn.o
+iwlagn-objs := iwl-agn.o iwl-agn-rs.o
+
+iwlagn-$(CONFIG_IWL4965) += iwl-4965.o
+iwlagn-$(CONFIG_IWL5000) += iwl-5000.o
+
obj-$(CONFIG_IWL3945) += iwl3945.o
iwl3945-objs := iwl3945-base.o iwl-3945.o iwl-3945-rs.o
iwl3945-$(CONFIG_IWL3945_LEDS) += iwl-3945-led.o
-obj-$(CONFIG_IWL4965) += iwl4965.o
-iwl4965-objs := iwl4965-base.o iwl-4965.o iwl-4965-rs.o
-
-ifeq ($(CONFIG_IWL5000),y)
- iwl4965-objs += iwl-5000.o
-endif
-
static int iwl3945_led_register_led(struct iwl3945_priv *priv,
struct iwl3945_led *led,
enum led_type type, u8 set_led,
- const char *name, char *trigger)
+ char *trigger)
{
struct device *device = wiphy_dev(priv->hw->wiphy);
int ret;
- led->led_dev.name = name;
+ led->led_dev.name = led->name;
led->led_dev.brightness_set = iwl3945_led_brightness_set;
led->led_dev.default_trigger = trigger;
int iwl3945_led_register(struct iwl3945_priv *priv)
{
char *trigger;
- char name[32];
int ret;
priv->last_blink_rate = 0;
priv->allow_blinking = 0;
trigger = ieee80211_get_radio_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:radio",
+ snprintf(priv->led[IWL_LED_TRG_RADIO].name,
+ sizeof(priv->led[IWL_LED_TRG_RADIO].name), "iwl-%s:radio",
wiphy_name(priv->hw->wiphy));
priv->led[IWL_LED_TRG_RADIO].led_on = iwl3945_led_on;
ret = iwl3945_led_register_led(priv,
&priv->led[IWL_LED_TRG_RADIO],
- IWL_LED_TRG_RADIO, 1,
- name, trigger);
+ IWL_LED_TRG_RADIO, 1, trigger);
+
if (ret)
goto exit_fail;
trigger = ieee80211_get_assoc_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:assoc",
+ snprintf(priv->led[IWL_LED_TRG_ASSOC].name,
+ sizeof(priv->led[IWL_LED_TRG_ASSOC].name), "iwl-%s:assoc",
wiphy_name(priv->hw->wiphy));
ret = iwl3945_led_register_led(priv,
&priv->led[IWL_LED_TRG_ASSOC],
- IWL_LED_TRG_ASSOC, 0,
- name, trigger);
+ IWL_LED_TRG_ASSOC, 0, trigger);
+
/* for assoc always turn led on */
priv->led[IWL_LED_TRG_ASSOC].led_on = iwl3945_led_on;
priv->led[IWL_LED_TRG_ASSOC].led_off = iwl3945_led_on;
goto exit_fail;
trigger = ieee80211_get_rx_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:RX",
+ snprintf(priv->led[IWL_LED_TRG_RX].name,
+ sizeof(priv->led[IWL_LED_TRG_RX].name), "iwl-%s:RX",
wiphy_name(priv->hw->wiphy));
-
ret = iwl3945_led_register_led(priv,
&priv->led[IWL_LED_TRG_RX],
- IWL_LED_TRG_RX, 0,
- name, trigger);
+ IWL_LED_TRG_RX, 0, trigger);
priv->led[IWL_LED_TRG_RX].led_on = iwl3945_led_associated;
priv->led[IWL_LED_TRG_RX].led_off = iwl3945_led_associated;
goto exit_fail;
trigger = ieee80211_get_tx_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:TX",
+ snprintf(priv->led[IWL_LED_TRG_TX].name,
+ sizeof(priv->led[IWL_LED_TRG_TX].name), "iwl-%s:TX",
wiphy_name(priv->hw->wiphy));
ret = iwl3945_led_register_led(priv,
&priv->led[IWL_LED_TRG_TX],
- IWL_LED_TRG_TX, 0,
- name, trigger);
+ IWL_LED_TRG_TX, 0, trigger);
+
priv->led[IWL_LED_TRG_TX].led_on = iwl3945_led_associated;
priv->led[IWL_LED_TRG_TX].led_off = iwl3945_led_associated;
priv->led[IWL_LED_TRG_TX].led_pattern = iwl3945_led_pattern;
struct iwl3945_led {
struct iwl3945_priv *priv;
struct led_classdev led_dev;
+ char name[32];
int (*led_on) (struct iwl3945_priv *priv, int led_id);
int (*led_off) (struct iwl3945_priv *priv, int led_id);
struct ieee80211_rx_status *stats)
{
struct iwl3945_rx_packet *pkt = (struct iwl3945_rx_packet *)rxb->skb->data;
+#ifdef CONFIG_IWL3945_LEDS
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)IWL_RX_DATA(pkt);
+#endif
struct iwl3945_rx_frame_hdr *rx_hdr = IWL_RX_HDR(pkt);
struct iwl3945_rx_frame_end *rx_end = IWL_RX_END(pkt);
short len = le16_to_cpu(rx_hdr->len);
return;
}
- if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) {
- iwl3945_pass_packet_to_mac80211(priv, rxb, &rx_status);
- return;
- }
+
/* Convert 3945's rssi indicator to dBm */
rx_status.signal = rx_stats->rssi - IWL_RSSI_OFFSET;
priv->last_rx_noise = rx_status.noise;
}
+ if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) {
+ iwl3945_pass_packet_to_mac80211(priv, rxb, &rx_status);
+ return;
+ }
+
switch (le16_to_cpu(header->frame_control) & IEEE80211_FCTL_FTYPE) {
case IEEE80211_FTYPE_MGMT:
switch (le16_to_cpu(header->frame_control) &
struct ieee80211_mgmt *mgmt =
(struct ieee80211_mgmt *)header;
__le32 *pos;
- pos =
- (__le32 *) & mgmt->u.beacon.
+ pos = (__le32 *)&mgmt->u.beacon.
timestamp;
priv->timestamp0 = le32_to_cpu(pos[0]);
priv->timestamp1 = le32_to_cpu(pos[1]);
*/
static inline int iwl3945_hw_reg_temp_out_of_range(int temperature)
{
- return (((temperature < -260) || (temperature > 25)) ? 1 : 0);
+ return ((temperature < -260) || (temperature > 25)) ? 1 : 0;
}
int iwl3945_hw_get_temperature(struct iwl3945_priv *priv)
tx_beacon_cmd->tx.supp_rates[1] =
(IWL_CCK_BASIC_RATES_MASK & 0xF);
- return (sizeof(struct iwl3945_tx_beacon_cmd) + frame_size);
+ return sizeof(struct iwl3945_tx_beacon_cmd) + frame_size;
}
void iwl3945_hw_rx_handler_setup(struct iwl3945_priv *priv)
return -EINVAL;
}
-int iwl4965_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src)
-{
- int ret;
- unsigned long flags;
-
- spin_lock_irqsave(&priv->lock, flags);
- ret = iwl_grab_nic_access(priv);
- if (ret) {
- spin_unlock_irqrestore(&priv->lock, flags);
- return ret;
- }
-
- if (src == IWL_PWR_SRC_VAUX) {
- u32 val;
- ret = pci_read_config_dword(priv->pci_dev, PCI_POWER_SOURCE,
- &val);
-
- if (val & PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT) {
- iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
- APMG_PS_CTRL_VAL_PWR_SRC_VAUX,
- ~APMG_PS_CTRL_MSK_PWR_SRC);
- }
- } else {
- iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
- APMG_PS_CTRL_VAL_PWR_SRC_VMAIN,
- ~APMG_PS_CTRL_MSK_PWR_SRC);
- }
-
- iwl_release_nic_access(priv);
- spin_unlock_irqrestore(&priv->lock, flags);
-
- return ret;
-}
/*
* Activate/Deactivat Tx DMA/FIFO channels according tx fifos mask
return 0;
}
-/* set card power command */
-static int iwl4965_set_power(struct iwl_priv *priv,
- void *cmd)
-{
- int ret = 0;
-
- ret = iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
- sizeof(struct iwl4965_powertable_cmd),
- cmd, NULL);
- return ret;
-}
-
static s32 iwl4965_math_div_round(s32 num, s32 denom, s32 *res)
{
s32 sign = 1;
c, atten_value, power_index,
tx_power.s.radio_tx_gain[c],
tx_power.s.dsp_predis_atten[c]);
- }/* for each chain */
+ } /* for each chain */
tx_power_tbl->power_tbl[i].dw = cpu_to_le32(tx_power.dw);
- }/* for each rate */
+ } /* for each rate */
return 0;
}
return le32_to_cpu(s->rb_closed) & 0xFFF;
}
-unsigned int iwl4965_hw_get_beacon_cmd(struct iwl_priv *priv,
- struct iwl_frame *frame, u8 rate)
-{
- struct iwl4965_tx_beacon_cmd *tx_beacon_cmd;
- unsigned int frame_size;
-
- tx_beacon_cmd = &frame->u.beacon;
- memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd));
-
- tx_beacon_cmd->tx.sta_id = priv->hw_params.bcast_sta_id;
- tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
-
- frame_size = iwl4965_fill_beacon_frame(priv,
- tx_beacon_cmd->frame,
- iwl_bcast_addr,
- sizeof(frame->u) - sizeof(*tx_beacon_cmd));
-
- BUG_ON(frame_size > MAX_MPDU_SIZE);
- tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size);
-
- if ((rate == IWL_RATE_1M_PLCP) || (rate >= IWL_RATE_2M_PLCP))
- tx_beacon_cmd->tx.rate_n_flags =
- iwl_hw_set_rate_n_flags(rate, RATE_MCS_CCK_MSK);
- else
- tx_beacon_cmd->tx.rate_n_flags =
- iwl_hw_set_rate_n_flags(rate, 0);
-
- tx_beacon_cmd->tx.tx_flags = (TX_CMD_FLG_SEQ_CTL_MSK |
- TX_CMD_FLG_TSF_MSK | TX_CMD_FLG_STA_RATE_MSK);
- return (sizeof(*tx_beacon_cmd) + frame_size);
-}
-
static int iwl4965_alloc_shared_mem(struct iwl_priv *priv)
{
priv->shared_virt = pci_alloc_consistent(priv->pci_dev,
return 0;
}
-int iwl4965_mac_ampdu_action(struct ieee80211_hw *hw,
- enum ieee80211_ampdu_mlme_action action,
- const u8 *addr, u16 tid, u16 *ssn)
-{
- struct iwl_priv *priv = hw->priv;
- DECLARE_MAC_BUF(mac);
-
- IWL_DEBUG_HT("A-MPDU action on addr %s tid %d\n",
- print_mac(mac, addr), tid);
-
- if (!(priv->cfg->sku & IWL_SKU_N))
- return -EACCES;
-
- switch (action) {
- case IEEE80211_AMPDU_RX_START:
- IWL_DEBUG_HT("start Rx\n");
- return iwl_rx_agg_start(priv, addr, tid, *ssn);
- case IEEE80211_AMPDU_RX_STOP:
- IWL_DEBUG_HT("stop Rx\n");
- return iwl_rx_agg_stop(priv, addr, tid);
- case IEEE80211_AMPDU_TX_START:
- IWL_DEBUG_HT("start Tx\n");
- return iwl_tx_agg_start(priv, addr, tid, ssn);
- case IEEE80211_AMPDU_TX_STOP:
- IWL_DEBUG_HT("stop Tx\n");
- return iwl_tx_agg_stop(priv, addr, tid);
- default:
- IWL_DEBUG_HT("unknown\n");
- return -EINVAL;
- break;
- }
- return 0;
-}
static u16 iwl4965_get_hcmd_size(u8 cmd_id, u16 len)
{
bitmap = bitmap << sh;
sh = 0;
}
- bitmap |= (1 << sh);
- IWL_DEBUG_TX_REPLY("start=%d bitmap=0x%x\n",
- start, (u32)(bitmap & 0xFFFFFFFF));
+ bitmap |= 1ULL << sh;
+ IWL_DEBUG_TX_REPLY("start=%d bitmap=0x%llx\n",
+ start, (unsigned long long)bitmap);
}
agg->bitmap = bitmap;
IWL_ERROR("TODO: Implement Tx ABORT REQUIRED!!!\n");
}
+static int iwl4965_calc_rssi(struct iwl_priv *priv,
+ struct iwl_rx_phy_res *rx_resp)
+{
+ /* data from PHY/DSP regarding signal strength, etc.,
+ * contents are always there, not configurable by host. */
+ struct iwl4965_rx_non_cfg_phy *ncphy =
+ (struct iwl4965_rx_non_cfg_phy *)rx_resp->non_cfg_phy_buf;
+ u32 agc = (le16_to_cpu(ncphy->agc_info) & IWL49_AGC_DB_MASK)
+ >> IWL49_AGC_DB_POS;
+
+ u32 valid_antennae =
+ (le16_to_cpu(rx_resp->phy_flags) & IWL49_RX_PHY_FLAGS_ANTENNAE_MASK)
+ >> IWL49_RX_PHY_FLAGS_ANTENNAE_OFFSET;
+ u8 max_rssi = 0;
+ u32 i;
+
+ /* Find max rssi among 3 possible receivers.
+ * These values are measured by the digital signal processor (DSP).
+ * They should stay fairly constant even as the signal strength varies,
+ * if the radio's automatic gain control (AGC) is working right.
+ * AGC value (see below) will provide the "interesting" info. */
+ for (i = 0; i < 3; i++)
+ if (valid_antennae & (1 << i))
+ max_rssi = max(ncphy->rssi_info[i << 1], max_rssi);
+
+ IWL_DEBUG_STATS("Rssi In A %d B %d C %d Max %d AGC dB %d\n",
+ ncphy->rssi_info[0], ncphy->rssi_info[2], ncphy->rssi_info[4],
+ max_rssi, agc);
+
+ /* dBm = max_rssi dB - agc dB - constant.
+ * Higher AGC (higher radio gain) means lower signal. */
+ return max_rssi - agc - IWL_RSSI_OFFSET;
+}
+
/* Set up 4965-specific Rx frame reply handlers */
static void iwl4965_rx_handler_setup(struct iwl_priv *priv)
.chain_noise_reset = iwl4965_chain_noise_reset,
.gain_computation = iwl4965_gain_computation,
.rts_tx_cmd_flag = iwl4965_rts_tx_cmd_flag,
+ .calc_rssi = iwl4965_calc_rssi,
};
static struct iwl_lib_ops iwl4965_lib = {
.check_version = iwl4965_eeprom_check_version,
.query_addr = iwlcore_eeprom_query_addr,
},
- .set_power = iwl4965_set_power,
.send_tx_power = iwl4965_send_tx_power,
.update_chain_flags = iwl4965_update_chain_flags,
.temperature = iwl4965_temperature_calib,
module_param_named(disable, iwl4965_mod_params.disable, int, 0444);
MODULE_PARM_DESC(disable, "manually disable the radio (default 0 [radio on])");
module_param_named(swcrypto, iwl4965_mod_params.sw_crypto, int, 0444);
-MODULE_PARM_DESC(swcrypto, "using crypto in software (default 0 [hardware])\n");
+MODULE_PARM_DESC(swcrypto, "using crypto in software (default 0 [hardware])");
module_param_named(debug, iwl4965_mod_params.debug, int, 0444);
MODULE_PARM_DESC(debug, "debug output mask");
module_param_named(
iwl_set_bit(priv, CSR_GIO_CHICKEN_BITS,
CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX);
+ /* Set FH wait treshold to maximum (HW error during stress W/A) */
+ iwl_set_bit(priv, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL);
+
+ /* enable HAP INTA to move device L1a -> L0s */
+ iwl_set_bit(priv, CSR_HW_IF_CONFIG_REG,
+ CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A);
+
iwl_set_bit(priv, CSR_ANA_PLL_CFG, CSR50_ANA_PLL_CFG_VAL);
/* set "initialization complete" bit to move adapter
CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI |
CSR_HW_IF_CONFIG_REG_BIT_MAC_SI);
+ /* W/A : NIC is stuck in a reset state after Early PCIe power off
+ * (PCIe power is lost before PERST# is asserted),
+ * causing ME FW to lose ownership and not being able to obtain it back.
+ */
+ iwl_grab_nic_access(priv);
+ iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
+ APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS,
+ ~APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS);
+ iwl_release_nic_access(priv);
+
spin_unlock_irqrestore(&priv->lock, flags);
}
len = byte_cnt + IWL_TX_CRC_SIZE + IWL_TX_DELIMITER_SIZE;
if (txq_id != IWL_CMD_QUEUE_NUM) {
- sta = txq->cmd[txq->q.write_ptr].cmd.tx.sta_id;
- sec_ctl = txq->cmd[txq->q.write_ptr].cmd.tx.sec_ctl;
+ sta = txq->cmd[txq->q.write_ptr]->cmd.tx.sta_id;
+ sec_ctl = txq->cmd[txq->q.write_ptr]->cmd.tx.sec_ctl;
switch (sec_ctl & TX_CMD_SEC_MSK) {
case TX_CMD_SEC_CCM:
u8 sta = 0;
if (txq_id != IWL_CMD_QUEUE_NUM)
- sta = txq->cmd[txq->q.read_ptr].cmd.tx.sta_id;
+ sta = txq->cmd[txq->q.read_ptr]->cmd.tx.sta_id;
shared_data->queues_byte_cnt_tbls[txq_id].tfd_offset[txq->q.read_ptr].
val = cpu_to_le16(1 | (sta << 12));
static inline u32 iwl5000_get_scd_ssn(struct iwl5000_tx_resp *tx_resp)
{
- return le32_to_cpup((__le32*)&tx_resp->status +
+ return le32_to_cpup((__le32 *)&tx_resp->status +
tx_resp->frame_count) & MAX_SN;
}
bitmap = bitmap << sh;
sh = 0;
}
- bitmap |= (1 << sh);
- IWL_DEBUG_TX_REPLY("start=%d bitmap=0x%x\n",
- start, (u32)(bitmap & 0xFFFFFFFF));
+ bitmap |= 1ULL << sh;
+ IWL_DEBUG_TX_REPLY("start=%d bitmap=0x%llx\n",
+ start, (unsigned long long)bitmap);
}
agg->bitmap = bitmap;
priv->temperature = le32_to_cpu(priv->statistics.general.temperature);
}
+/* Calc max signal level (dBm) among 3 possible receivers */
+static int iwl5000_calc_rssi(struct iwl_priv *priv,
+ struct iwl_rx_phy_res *rx_resp)
+{
+ /* data from PHY/DSP regarding signal strength, etc.,
+ * contents are always there, not configurable by host
+ */
+ struct iwl5000_non_cfg_phy *ncphy =
+ (struct iwl5000_non_cfg_phy *)rx_resp->non_cfg_phy_buf;
+ u32 val, rssi_a, rssi_b, rssi_c, max_rssi;
+ u8 agc;
+
+ val = le32_to_cpu(ncphy->non_cfg_phy[IWL50_RX_RES_AGC_IDX]);
+ agc = (val & IWL50_OFDM_AGC_MSK) >> IWL50_OFDM_AGC_BIT_POS;
+
+ /* Find max rssi among 3 possible receivers.
+ * These values are measured by the digital signal processor (DSP).
+ * They should stay fairly constant even as the signal strength varies,
+ * if the radio's automatic gain control (AGC) is working right.
+ * AGC value (see below) will provide the "interesting" info.
+ */
+ val = le32_to_cpu(ncphy->non_cfg_phy[IWL50_RX_RES_RSSI_AB_IDX]);
+ rssi_a = (val & IWL50_OFDM_RSSI_A_MSK) >> IWL50_OFDM_RSSI_A_BIT_POS;
+ rssi_b = (val & IWL50_OFDM_RSSI_B_MSK) >> IWL50_OFDM_RSSI_B_BIT_POS;
+ val = le32_to_cpu(ncphy->non_cfg_phy[IWL50_RX_RES_RSSI_C_IDX]);
+ rssi_c = (val & IWL50_OFDM_RSSI_C_MSK) >> IWL50_OFDM_RSSI_C_BIT_POS;
+
+ max_rssi = max_t(u32, rssi_a, rssi_b);
+ max_rssi = max_t(u32, max_rssi, rssi_c);
+
+ IWL_DEBUG_STATS("Rssi In A %d B %d C %d Max %d AGC dB %d\n",
+ rssi_a, rssi_b, rssi_c, max_rssi, agc);
+
+ /* dBm = max_rssi dB - agc dB - constant.
+ * Higher AGC (higher radio gain) means lower signal. */
+ return max_rssi - agc - IWL_RSSI_OFFSET;
+}
+
static struct iwl_hcmd_ops iwl5000_hcmd = {
.rxon_assoc = iwl5000_send_rxon_assoc,
};
.gain_computation = iwl5000_gain_computation,
.chain_noise_reset = iwl5000_chain_noise_reset,
.rts_tx_cmd_flag = iwl5000_rts_tx_cmd_flag,
+ .calc_rssi = iwl5000_calc_rssi,
};
static struct iwl_lib_ops iwl5000_lib = {
.alive_notify = iwl5000_alive_notify,
.send_tx_power = iwl5000_send_tx_power,
.temperature = iwl5000_temperature,
+ .update_chain_flags = iwl4965_update_chain_flags,
.apm_ops = {
.init = iwl5000_apm_init,
.reset = iwl5000_apm_reset,
#include "iwl-core.h"
#include "iwl-helpers.h"
-#define RS_NAME "iwl-4965-rs"
+#define RS_NAME "iwl-agn-rs"
#define NUM_TRY_BEFORE_ANT_TOGGLE 1
#define IWL_NUMBER_TRY 1
};
/**
- * struct iwl4965_rate_scale_data -- tx success history for one rate
+ * struct iwl_rate_scale_data -- tx success history for one rate
*/
-struct iwl4965_rate_scale_data {
+struct iwl_rate_scale_data {
u64 data; /* bitmap of successful frames */
s32 success_counter; /* number of frames successful */
s32 success_ratio; /* per-cent * 128 */
};
/**
- * struct iwl4965_scale_tbl_info -- tx params and success history for all rates
+ * struct iwl_scale_tbl_info -- tx params and success history for all rates
*
- * There are two of these in struct iwl4965_lq_sta,
+ * There are two of these in struct iwl_lq_sta,
* one for "active", and one for "search".
*/
-struct iwl4965_scale_tbl_info {
+struct iwl_scale_tbl_info {
enum iwl_table_type lq_type;
u8 ant_type;
u8 is_SGI; /* 1 = short guard interval */
u8 action; /* change modulation; IWL_[LEGACY/SISO/MIMO]_SWITCH_* */
s32 *expected_tpt; /* throughput metrics; expected_tpt_G, etc. */
u32 current_rate; /* rate_n_flags, uCode API format */
- struct iwl4965_rate_scale_data win[IWL_RATE_COUNT]; /* rate histories */
+ struct iwl_rate_scale_data win[IWL_RATE_COUNT]; /* rate histories */
};
-struct iwl4965_traffic_load {
+struct iwl_traffic_load {
unsigned long time_stamp; /* age of the oldest statistics */
u32 packet_count[TID_QUEUE_MAX_SIZE]; /* packet count in this time
* slice */
};
/**
- * struct iwl4965_lq_sta -- driver's rate scaling private structure
+ * struct iwl_lq_sta -- driver's rate scaling private structure
*
* Pointer to this gets passed back and forth between driver and mac80211.
*/
-struct iwl4965_lq_sta {
+struct iwl_lq_sta {
u8 active_tbl; /* index of active table, range 0-1 */
u8 enable_counter; /* indicates HT mode */
u8 stay_in_tbl; /* 1: disallow, 0: allow search for new mode */
u16 active_rate_basic;
struct iwl_link_quality_cmd lq;
- struct iwl4965_scale_tbl_info lq_info[LQ_SIZE]; /* "active", "search" */
- struct iwl4965_traffic_load load[TID_MAX_LOAD_COUNT];
+ struct iwl_scale_tbl_info lq_info[LQ_SIZE]; /* "active", "search" */
+ struct iwl_traffic_load load[TID_MAX_LOAD_COUNT];
u8 tx_agg_tid_en;
#ifdef CONFIG_MAC80211_DEBUGFS
struct dentry *rs_sta_dbgfs_scale_table_file;
struct ieee80211_hdr *hdr,
struct sta_info *sta);
static void rs_fill_link_cmd(const struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
- u32 rate_n_flags);
+ struct iwl_lq_sta *lq_sta, u32 rate_n_flags);
#ifdef CONFIG_MAC80211_DEBUGFS
-static void rs_dbgfs_set_mcs(struct iwl4965_lq_sta *lq_sta,
- u32 *rate_n_flags, int index);
+static void rs_dbgfs_set_mcs(struct iwl_lq_sta *lq_sta,
+ u32 *rate_n_flags, int index);
#else
-static void rs_dbgfs_set_mcs(struct iwl4965_lq_sta *lq_sta,
- u32 *rate_n_flags, int index)
+static void rs_dbgfs_set_mcs(struct iwl_lq_sta *lq_sta,
+ u32 *rate_n_flags, int index)
{}
#endif
return (u8)(rate_n_flags & 0xFF);
}
-static void rs_rate_scale_clear_window(struct iwl4965_rate_scale_data *window)
+static void rs_rate_scale_clear_window(struct iwl_rate_scale_data *window)
{
window->data = 0;
window->success_counter = 0;
static inline u8 rs_is_valid_ant(u8 valid_antenna, u8 ant_type)
{
- return ((ant_type & valid_antenna) == ant_type);
+ return (ant_type & valid_antenna) == ant_type;
}
/*
* removes the old data from the statistics. All data that is older than
* TID_MAX_TIME_DIFF, will be deleted.
*/
-static void rs_tl_rm_old_stats(struct iwl4965_traffic_load *tl, u32 curr_time)
+static void rs_tl_rm_old_stats(struct iwl_traffic_load *tl, u32 curr_time)
{
/* The oldest age we want to keep */
u32 oldest_time = curr_time - TID_MAX_TIME_DIFF;
* increment traffic load value for tid and also remove
* any old values if passed the certain time period
*/
-static u8 rs_tl_add_packet(struct iwl4965_lq_sta *lq_data,
+static u8 rs_tl_add_packet(struct iwl_lq_sta *lq_data,
struct ieee80211_hdr *hdr)
{
u32 curr_time = jiffies_to_msecs(jiffies);
u32 time_diff;
s32 index;
- struct iwl4965_traffic_load *tl = NULL;
+ struct iwl_traffic_load *tl = NULL;
__le16 fc = hdr->frame_control;
u8 tid;
/*
get the traffic load value for tid
*/
-static u32 rs_tl_get_load(struct iwl4965_lq_sta *lq_data, u8 tid)
+static u32 rs_tl_get_load(struct iwl_lq_sta *lq_data, u8 tid)
{
u32 curr_time = jiffies_to_msecs(jiffies);
u32 time_diff;
s32 index;
- struct iwl4965_traffic_load *tl = NULL;
+ struct iwl_traffic_load *tl = NULL;
if (tid >= TID_MAX_LOAD_COUNT)
return 0;
}
static void rs_tl_turn_on_agg_for_tid(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_data, u8 tid,
- struct sta_info *sta)
+ struct iwl_lq_sta *lq_data, u8 tid,
+ struct sta_info *sta)
{
unsigned long state;
DECLARE_MAC_BUF(mac);
}
static void rs_tl_turn_on_agg(struct iwl_priv *priv, u8 tid,
- struct iwl4965_lq_sta *lq_data,
- struct sta_info *sta)
+ struct iwl_lq_sta *lq_data,
+ struct sta_info *sta)
{
if ((tid < TID_MAX_LOAD_COUNT))
rs_tl_turn_on_agg_for_tid(priv, lq_data, tid, sta);
static inline int get_num_of_ant_from_rate(u32 rate_n_flags)
{
- return (!!(rate_n_flags & RATE_MCS_ANT_A_MSK) +
- !!(rate_n_flags & RATE_MCS_ANT_B_MSK) +
- !!(rate_n_flags & RATE_MCS_ANT_C_MSK));
+ return !!(rate_n_flags & RATE_MCS_ANT_A_MSK) +
+ !!(rate_n_flags & RATE_MCS_ANT_B_MSK) +
+ !!(rate_n_flags & RATE_MCS_ANT_C_MSK);
}
/**
* at this rate. window->data contains the bitmask of successful
* packets.
*/
-static int rs_collect_tx_data(struct iwl4965_rate_scale_data *windows,
+static int rs_collect_tx_data(struct iwl_rate_scale_data *windows,
int scale_index, s32 tpt, int retries,
int successes)
{
- struct iwl4965_rate_scale_data *window = NULL;
+ struct iwl_rate_scale_data *window = NULL;
static const u64 mask = (((u64)1) << (IWL_RATE_MAX_WINDOW - 1));
s32 fail_count;
* Fill uCode API rate_n_flags field, based on "search" or "active" table.
*/
/* FIXME:RS:remove this function and put the flags statically in the table */
-static u32 rate_n_flags_from_tbl(struct iwl4965_scale_tbl_info *tbl,
+static u32 rate_n_flags_from_tbl(struct iwl_scale_tbl_info *tbl,
int index, u8 use_green)
{
u32 rate_n_flags = 0;
*/
static int rs_get_tbl_info_from_mcs(const u32 rate_n_flags,
enum ieee80211_band band,
- struct iwl4965_scale_tbl_info *tbl,
+ struct iwl_scale_tbl_info *tbl,
int *rate_idx)
{
u32 ant_msk = (rate_n_flags & RATE_MCS_ANT_ABC_MSK);
/* switch to another antenna/antennas and return 1 */
/* if no other valid antenna found, return 0 */
static int rs_toggle_antenna(u32 valid_ant, u32 *rate_n_flags,
- struct iwl4965_scale_tbl_info *tbl)
+ struct iwl_scale_tbl_info *tbl)
{
u8 new_ant_type;
#if 0
static inline u8 rs_use_green(struct iwl_priv *priv, struct ieee80211_conf *conf)
{
- return ((conf->flags & IEEE80211_CONF_SUPPORT_HT_MODE) &&
+ return (conf->flags & IEEE80211_CONF_SUPPORT_HT_MODE) &&
priv->current_ht_config.is_green_field &&
- !priv->current_ht_config.non_GF_STA_present);
+ !priv->current_ht_config.non_GF_STA_present;
}
#endif
static inline u8 rs_use_green(struct iwl_priv *priv, struct ieee80211_conf *conf)
* basic available rates.
*
*/
-static u16 rs_get_supported_rates(struct iwl4965_lq_sta *lq_sta,
- struct ieee80211_hdr *hdr,
- enum iwl_table_type rate_type)
+static u16 rs_get_supported_rates(struct iwl_lq_sta *lq_sta,
+ struct ieee80211_hdr *hdr,
+ enum iwl_table_type rate_type)
{
if (hdr && is_multicast_ether_addr(hdr->addr1) &&
lq_sta->active_rate_basic)
return (high << 8) | low;
}
-static u32 rs_get_lower_rate(struct iwl4965_lq_sta *lq_sta,
- struct iwl4965_scale_tbl_info *tbl, u8 scale_index,
- u8 ht_possible)
+static u32 rs_get_lower_rate(struct iwl_lq_sta *lq_sta,
+ struct iwl_scale_tbl_info *tbl,
+ u8 scale_index, u8 ht_possible)
{
s32 low;
u16 rate_mask;
int status;
u8 retries;
int rs_index, index = 0;
- struct iwl4965_lq_sta *lq_sta;
+ struct iwl_lq_sta *lq_sta;
struct iwl_link_quality_cmd *table;
struct sta_info *sta;
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
struct ieee80211_hw *hw = local_to_hw(local);
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
- struct iwl4965_rate_scale_data *window = NULL;
- struct iwl4965_rate_scale_data *search_win = NULL;
+ struct iwl_rate_scale_data *window = NULL;
+ struct iwl_rate_scale_data *search_win = NULL;
u32 tx_rate;
- struct iwl4965_scale_tbl_info tbl_type;
- struct iwl4965_scale_tbl_info *curr_tbl, *search_tbl;
+ struct iwl_scale_tbl_info tbl_type;
+ struct iwl_scale_tbl_info *curr_tbl, *search_tbl;
u8 active_index = 0;
__le16 fc = hdr->frame_control;
s32 tpt = 0;
goto out;
- lq_sta = (struct iwl4965_lq_sta *)sta->rate_ctrl_priv;
+ lq_sta = (struct iwl_lq_sta *)sta->rate_ctrl_priv;
if ((priv->iw_mode == IEEE80211_IF_TYPE_IBSS) &&
!lq_sta->ibss_sta_added)
curr_tbl = &(lq_sta->lq_info[active_index]);
search_tbl = &(lq_sta->lq_info[(1 - active_index)]);
- window = (struct iwl4965_rate_scale_data *)
- &(curr_tbl->win[0]);
- search_win = (struct iwl4965_rate_scale_data *)
- &(search_tbl->win[0]);
+ window = (struct iwl_rate_scale_data *)&(curr_tbl->win[0]);
+ search_win = (struct iwl_rate_scale_data *)&(search_tbl->win[0]);
/*
* Ignore this Tx frame response if its initial rate doesn't match
* searching for a new mode.
*/
static void rs_set_stay_in_table(struct iwl_priv *priv, u8 is_legacy,
- struct iwl4965_lq_sta *lq_sta)
+ struct iwl_lq_sta *lq_sta)
{
IWL_DEBUG_RATE("we are staying in the same table\n");
lq_sta->stay_in_tbl = 1; /* only place this gets set */
/*
* Find correct throughput table for given mode of modulation
*/
-static void rs_set_expected_tpt_table(struct iwl4965_lq_sta *lq_sta,
- struct iwl4965_scale_tbl_info *tbl)
+static void rs_set_expected_tpt_table(struct iwl_lq_sta *lq_sta,
+ struct iwl_scale_tbl_info *tbl)
{
if (is_legacy(tbl->lq_type)) {
if (!is_a_band(tbl->lq_type))
* bit rate will typically need to increase, but not if performance was bad.
*/
static s32 rs_get_best_rate(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
- struct iwl4965_scale_tbl_info *tbl, /* "search" */
+ struct iwl_lq_sta *lq_sta,
+ struct iwl_scale_tbl_info *tbl, /* "search" */
u16 rate_mask, s8 index)
{
/* "active" values */
- struct iwl4965_scale_tbl_info *active_tbl =
+ struct iwl_scale_tbl_info *active_tbl =
&(lq_sta->lq_info[lq_sta->active_tbl]);
s32 active_sr = active_tbl->win[index].success_ratio;
s32 active_tpt = active_tbl->expected_tpt[index];
* Set up search table for MIMO
*/
static int rs_switch_to_mimo2(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
+ struct iwl_lq_sta *lq_sta,
struct ieee80211_conf *conf,
struct sta_info *sta,
- struct iwl4965_scale_tbl_info *tbl, int index)
+ struct iwl_scale_tbl_info *tbl, int index)
{
u16 rate_mask;
s32 rate;
* Set up search table for SISO
*/
static int rs_switch_to_siso(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
+ struct iwl_lq_sta *lq_sta,
struct ieee80211_conf *conf,
struct sta_info *sta,
- struct iwl4965_scale_tbl_info *tbl, int index)
+ struct iwl_scale_tbl_info *tbl, int index)
{
u16 rate_mask;
u8 is_green = lq_sta->is_green;
* Try to switch to new modulation mode from legacy
*/
static int rs_move_legacy_other(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
+ struct iwl_lq_sta *lq_sta,
struct ieee80211_conf *conf,
struct sta_info *sta,
int index)
{
- struct iwl4965_scale_tbl_info *tbl =
- &(lq_sta->lq_info[lq_sta->active_tbl]);
- struct iwl4965_scale_tbl_info *search_tbl =
- &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
- struct iwl4965_rate_scale_data *window = &(tbl->win[index]);
- u32 sz = (sizeof(struct iwl4965_scale_tbl_info) -
- (sizeof(struct iwl4965_rate_scale_data) * IWL_RATE_COUNT));
+ struct iwl_scale_tbl_info *tbl = &(lq_sta->lq_info[lq_sta->active_tbl]);
+ struct iwl_scale_tbl_info *search_tbl =
+ &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
+ struct iwl_rate_scale_data *window = &(tbl->win[index]);
+ u32 sz = (sizeof(struct iwl_scale_tbl_info) -
+ (sizeof(struct iwl_rate_scale_data) * IWL_RATE_COUNT));
u8 start_action = tbl->action;
u8 valid_tx_ant = priv->hw_params.valid_tx_ant;
int ret = 0;
* Try to switch to new modulation mode from SISO
*/
static int rs_move_siso_to_other(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
+ struct iwl_lq_sta *lq_sta,
struct ieee80211_conf *conf,
- struct sta_info *sta,
- int index)
+ struct sta_info *sta, int index)
{
u8 is_green = lq_sta->is_green;
- struct iwl4965_scale_tbl_info *tbl =
- &(lq_sta->lq_info[lq_sta->active_tbl]);
- struct iwl4965_scale_tbl_info *search_tbl =
- &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
- struct iwl4965_rate_scale_data *window = &(tbl->win[index]);
- u32 sz = (sizeof(struct iwl4965_scale_tbl_info) -
- (sizeof(struct iwl4965_rate_scale_data) * IWL_RATE_COUNT));
+ struct iwl_scale_tbl_info *tbl = &(lq_sta->lq_info[lq_sta->active_tbl]);
+ struct iwl_scale_tbl_info *search_tbl =
+ &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
+ struct iwl_rate_scale_data *window = &(tbl->win[index]);
+ u32 sz = (sizeof(struct iwl_scale_tbl_info) -
+ (sizeof(struct iwl_rate_scale_data) * IWL_RATE_COUNT));
u8 start_action = tbl->action;
u8 valid_tx_ant = priv->hw_params.valid_tx_ant;
int ret;
* Try to switch to new modulation mode from MIMO
*/
static int rs_move_mimo_to_other(struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
+ struct iwl_lq_sta *lq_sta,
struct ieee80211_conf *conf,
- struct sta_info *sta,
- int index)
+ struct sta_info *sta, int index)
{
s8 is_green = lq_sta->is_green;
- struct iwl4965_scale_tbl_info *tbl =
- &(lq_sta->lq_info[lq_sta->active_tbl]);
- struct iwl4965_scale_tbl_info *search_tbl =
- &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
- u32 sz = (sizeof(struct iwl4965_scale_tbl_info) -
- (sizeof(struct iwl4965_rate_scale_data) * IWL_RATE_COUNT));
+ struct iwl_scale_tbl_info *tbl = &(lq_sta->lq_info[lq_sta->active_tbl]);
+ struct iwl_scale_tbl_info *search_tbl =
+ &(lq_sta->lq_info[(1 - lq_sta->active_tbl)]);
+ u32 sz = (sizeof(struct iwl_scale_tbl_info) -
+ (sizeof(struct iwl_rate_scale_data) * IWL_RATE_COUNT));
u8 start_action = tbl->action;
/*u8 valid_tx_ant = priv->hw_params.valid_tx_ant;*/
int ret;
* 2) # times calling this function
* 3) elapsed time in this mode (not used, for now)
*/
-static void rs_stay_in_table(struct iwl4965_lq_sta *lq_sta)
+static void rs_stay_in_table(struct iwl_lq_sta *lq_sta)
{
- struct iwl4965_scale_tbl_info *tbl;
+ struct iwl_scale_tbl_info *tbl;
int i;
int active_tbl;
int flush_interval_passed = 0;
int high = IWL_RATE_INVALID;
int index;
int i;
- struct iwl4965_rate_scale_data *window = NULL;
+ struct iwl_rate_scale_data *window = NULL;
int current_tpt = IWL_INVALID_VALUE;
int low_tpt = IWL_INVALID_VALUE;
int high_tpt = IWL_INVALID_VALUE;
__le16 fc;
u16 rate_mask;
u8 update_lq = 0;
- struct iwl4965_lq_sta *lq_sta;
- struct iwl4965_scale_tbl_info *tbl, *tbl1;
+ struct iwl_lq_sta *lq_sta;
+ struct iwl_scale_tbl_info *tbl, *tbl1;
u16 rate_scale_index_msk = 0;
u32 rate;
u8 is_green = 0;
if (!sta || !sta->rate_ctrl_priv)
return;
- lq_sta = (struct iwl4965_lq_sta *)sta->rate_ctrl_priv;
+ lq_sta = (struct iwl_lq_sta *)sta->rate_ctrl_priv;
tid = rs_tl_add_packet(lq_sta, hdr);
struct ieee80211_conf *conf,
struct sta_info *sta)
{
- struct iwl4965_lq_sta *lq_sta;
- struct iwl4965_scale_tbl_info *tbl;
+ struct iwl_lq_sta *lq_sta;
+ struct iwl_scale_tbl_info *tbl;
int rate_idx;
int i;
u32 rate;
if (!sta || !sta->rate_ctrl_priv)
goto out;
- lq_sta = (struct iwl4965_lq_sta *)sta->rate_ctrl_priv;
+ lq_sta = (struct iwl_lq_sta *)sta->rate_ctrl_priv;
i = sta->last_txrate_idx;
if ((lq_sta->lq.sta_id == 0xff) &&
struct sta_info *sta;
__le16 fc;
struct iwl_priv *priv = (struct iwl_priv *)priv_rate;
- struct iwl4965_lq_sta *lq_sta;
+ struct iwl_lq_sta *lq_sta;
IWL_DEBUG_RATE_LIMIT("rate scale calculate new rate for skb\n");
goto out;
}
- lq_sta = (struct iwl4965_lq_sta *)sta->rate_ctrl_priv;
+ lq_sta = (struct iwl_lq_sta *)sta->rate_ctrl_priv;
i = sta->last_txrate_idx;
if ((priv->iw_mode == IEEE80211_IF_TYPE_IBSS) &&
static void *rs_alloc_sta(void *priv_rate, gfp_t gfp)
{
- struct iwl4965_lq_sta *lq_sta;
+ struct iwl_lq_sta *lq_sta;
struct iwl_priv *priv;
int i, j;
priv = (struct iwl_priv *)priv_rate;
IWL_DEBUG_RATE("create station rate scale window\n");
- lq_sta = kzalloc(sizeof(struct iwl4965_lq_sta), gfp);
+ lq_sta = kzalloc(sizeof(struct iwl_lq_sta), gfp);
if (lq_sta == NULL)
return NULL;
for (j = 0; j < LQ_SIZE; j++)
for (i = 0; i < IWL_RATE_COUNT; i++)
- rs_rate_scale_clear_window(&(lq_sta->lq_info[j].win[i]));
+ rs_rate_scale_clear_window(&lq_sta->lq_info[j].win[i]);
return lq_sta;
}
struct ieee80211_conf *conf = &local->hw.conf;
struct ieee80211_supported_band *sband;
struct iwl_priv *priv = (struct iwl_priv *)priv_rate;
- struct iwl4965_lq_sta *lq_sta = priv_sta;
+ struct iwl_lq_sta *lq_sta = priv_sta;
sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
sta->txrate_idx = 3;
for (j = 0; j < LQ_SIZE; j++)
for (i = 0; i < IWL_RATE_COUNT; i++)
- rs_rate_scale_clear_window(&(lq_sta->lq_info[j].win[i]));
+ rs_rate_scale_clear_window(&lq_sta->lq_info[j].win[i]);
IWL_DEBUG_RATE("LQ: *** rate scale global init ***\n");
/* TODO: what is a good starting rate for STA? About middle? Maybe not
}
static void rs_fill_link_cmd(const struct iwl_priv *priv,
- struct iwl4965_lq_sta *lq_sta,
- u32 new_rate)
+ struct iwl_lq_sta *lq_sta, u32 new_rate)
{
- struct iwl4965_scale_tbl_info tbl_type;
+ struct iwl_scale_tbl_info tbl_type;
int index = 0;
int rate_idx;
int repeat_rate = 0;
static void rs_clear(void *priv_rate)
{
+#ifdef CONFIG_IWLWIFI_DEBUG
struct iwl_priv *priv = (struct iwl_priv *) priv_rate;
IWL_DEBUG_RATE("enter\n");
/* TODO - add rate scale state reset */
IWL_DEBUG_RATE("leave\n");
+#endif /* CONFIG_IWLWIFI_DEBUG */
}
static void rs_free_sta(void *priv_rate, void *priv_sta)
{
- struct iwl4965_lq_sta *lq_sta = priv_sta;
+ struct iwl_lq_sta *lq_sta = priv_sta;
struct iwl_priv *priv;
priv = (struct iwl_priv *)priv_rate;
file->private_data = inode->i_private;
return 0;
}
-static void rs_dbgfs_set_mcs(struct iwl4965_lq_sta *lq_sta,
- u32 *rate_n_flags, int index)
+static void rs_dbgfs_set_mcs(struct iwl_lq_sta *lq_sta,
+ u32 *rate_n_flags, int index)
{
struct iwl_priv *priv;
static ssize_t rs_sta_dbgfs_scale_table_write(struct file *file,
const char __user *user_buf, size_t count, loff_t *ppos)
{
- struct iwl4965_lq_sta *lq_sta = file->private_data;
+ struct iwl_lq_sta *lq_sta = file->private_data;
struct iwl_priv *priv;
char buf[64];
int buf_size;
int desc = 0;
int i = 0;
- struct iwl4965_lq_sta *lq_sta = file->private_data;
+ struct iwl_lq_sta *lq_sta = file->private_data;
desc += sprintf(buff+desc, "sta_id %d\n", lq_sta->lq.sta_id);
desc += sprintf(buff+desc, "failed=%d success=%d rate=0%X\n",
int desc = 0;
int i, j;
- struct iwl4965_lq_sta *lq_sta = file->private_data;
+ struct iwl_lq_sta *lq_sta = file->private_data;
for (i = 0; i < LQ_SIZE; i++) {
desc += sprintf(buff+desc, "%s type=%d SGI=%d FAT=%d DUP=%d\n"
"rate=0x%X\n",
static void rs_add_debugfs(void *priv, void *priv_sta,
struct dentry *dir)
{
- struct iwl4965_lq_sta *lq_sta = priv_sta;
+ struct iwl_lq_sta *lq_sta = priv_sta;
lq_sta->rs_sta_dbgfs_scale_table_file =
debugfs_create_file("rate_scale_table", 0600, dir,
lq_sta, &rs_sta_dbgfs_scale_table_ops);
static void rs_remove_debugfs(void *priv, void *priv_sta)
{
- struct iwl4965_lq_sta *lq_sta = priv_sta;
+ struct iwl_lq_sta *lq_sta = priv_sta;
debugfs_remove(lq_sta->rs_sta_dbgfs_scale_table_file);
debugfs_remove(lq_sta->rs_sta_dbgfs_stats_table_file);
debugfs_remove(lq_sta->rs_sta_dbgfs_tx_agg_tid_en_file);
#endif
};
-int iwl4965_fill_rs_info(struct ieee80211_hw *hw, char *buf, u8 sta_id)
-{
- struct ieee80211_local *local = hw_to_local(hw);
- struct iwl_priv *priv = hw->priv;
- struct iwl4965_lq_sta *lq_sta;
- struct sta_info *sta;
- int cnt = 0, i;
- u32 samples = 0, success = 0, good = 0;
- unsigned long now = jiffies;
- u32 max_time = 0;
- u8 lq_type, antenna;
-
- rcu_read_lock();
-
- sta = sta_info_get(local, priv->stations[sta_id].sta.sta.addr);
- if (!sta || !sta->rate_ctrl_priv) {
- if (sta)
- IWL_DEBUG_RATE("leave - no private rate data!\n");
- else
- IWL_DEBUG_RATE("leave - no station!\n");
- rcu_read_unlock();
- return sprintf(buf, "station %d not found\n", sta_id);
- }
-
- lq_sta = (void *)sta->rate_ctrl_priv;
-
- lq_type = lq_sta->lq_info[lq_sta->active_tbl].lq_type;
- antenna = lq_sta->lq_info[lq_sta->active_tbl].ant_type;
-
- if (is_legacy(lq_type))
- i = IWL_RATE_54M_INDEX;
- else
- i = IWL_RATE_60M_INDEX;
- while (1) {
- u64 mask;
- int j;
- int active = lq_sta->active_tbl;
-
- cnt +=
- sprintf(&buf[cnt], " %2dMbs: ", iwl_rates[i].ieee / 2);
-
- mask = (1ULL << (IWL_RATE_MAX_WINDOW - 1));
- for (j = 0; j < IWL_RATE_MAX_WINDOW; j++, mask >>= 1)
- buf[cnt++] =
- (lq_sta->lq_info[active].win[i].data & mask)
- ? '1' : '0';
-
- samples += lq_sta->lq_info[active].win[i].counter;
- good += lq_sta->lq_info[active].win[i].success_counter;
- success += lq_sta->lq_info[active].win[i].success_counter *
- iwl_rates[i].ieee;
-
- if (lq_sta->lq_info[active].win[i].stamp) {
- int delta =
- jiffies_to_msecs(now -
- lq_sta->lq_info[active].win[i].stamp);
-
- if (delta > max_time)
- max_time = delta;
-
- cnt += sprintf(&buf[cnt], "%5dms\n", delta);
- } else
- buf[cnt++] = '\n';
-
- j = iwl4965_get_prev_ieee_rate(i);
- if (j == i)
- break;
- i = j;
- }
-
- /*
- * Display the average rate of all samples taken.
- * NOTE: We multiply # of samples by 2 since the IEEE measurement
- * added from iwl_rates is actually 2X the rate.
- */
- if (samples)
- cnt += sprintf(&buf[cnt],
- "\nAverage rate is %3d.%02dMbs over last %4dms\n"
- "%3d%% success (%d good packets over %d tries)\n",
- success / (2 * samples), (success * 5 / samples) % 10,
- max_time, good * 100 / samples, good, samples);
- else
- cnt += sprintf(&buf[cnt], "\nAverage rate: 0Mbs\n");
-
- cnt += sprintf(&buf[cnt], "\nrate scale type %d antenna %d "
- "active_search %d rate index %d\n", lq_type, antenna,
- lq_sta->search_better_tbl, sta->last_txrate_idx);
-
- rcu_read_unlock();
- return cnt;
-}
-
-int iwl4965_rate_control_register(void)
+int iwlagn_rate_control_register(void)
{
return ieee80211_rate_control_register(&rs_ops);
}
-void iwl4965_rate_control_unregister(void)
+void iwlagn_rate_control_unregister(void)
{
ieee80211_rate_control_unregister(&rs_ops);
}
*
*****************************************************************************/
-#ifndef __iwl_4965_rs_h__
-#define __iwl_4965_rs_h__
+#ifndef __iwl_agn_rs_h__
+#define __iwl_agn_rs_h__
#include "iwl-dev.h"
#define IWL_RATE_5M_MASK (1 << IWL_RATE_5M_INDEX)
#define IWL_RATE_11M_MASK (1 << IWL_RATE_11M_INDEX)
-/* 4965 uCode API values for legacy bit rates, both OFDM and CCK */
+/* uCode API values for legacy bit rates, both OFDM and CCK */
enum {
IWL_RATE_6M_PLCP = 13,
IWL_RATE_9M_PLCP = 15,
/*FIXME:RS:add IWL_RATE_LEGACY_INVM_PLCP = 0,*/
};
-/* 4965 uCode API values for OFDM high-throughput (HT) bit rates */
+/* uCode API values for OFDM high-throughput (HT) bit rates */
enum {
IWL_RATE_SISO_6M_PLCP = 0,
IWL_RATE_SISO_12M_PLCP = 1,
return rate;
}
-/**
- * iwl4965_fill_rs_info - Fill an output text buffer with the rate representation
- *
- * NOTE: This is provided as a quick mechanism for a user to visualize
- * the performance of the rate control algorithm and is not meant to be
- * parsed software.
- */
-extern int iwl4965_fill_rs_info(struct ieee80211_hw *, char *buf, u8 sta_id);
-
/**
* iwl4965_rate_control_register - Register the rate control algorithm callbacks
*
* ieee80211_register_hw
*
*/
-extern int iwl4965_rate_control_register(void);
+extern int iwlagn_rate_control_register(void);
/**
* iwl4965_rate_control_unregister - Unregister the rate control callbacks
* This should be called after calling ieee80211_unregister_hw, but before
* the driver is unloaded.
*/
-extern void iwl4965_rate_control_unregister(void);
+extern void iwlagn_rate_control_unregister(void);
-#endif
+#endif /* __iwl_agn__rs__ */
* NOTE: DRV_NAME is defined in iwlwifi.h for use by iwl-debug.h and printk
*/
-#define DRV_DESCRIPTION "Intel(R) Wireless WiFi Link 4965AGN driver for Linux"
+#define DRV_DESCRIPTION "Intel(R) Wireless WiFi Link AGN driver for Linux"
#ifdef CONFIG_IWLWIFI_DEBUG
#define VD "d"
#define VD
#endif
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
#define VS "s"
#else
#define VS
MODULE_VERSION(DRV_VERSION);
MODULE_AUTHOR(DRV_COPYRIGHT);
MODULE_LICENSE("GPL");
+MODULE_ALIAS("iwl4965");
/*************** STATION TABLE MANAGEMENT ****
* mac80211 should be examined to determine if sta_info is duplicating
list_add(&frame->list, &priv->free_frames);
}
-unsigned int iwl4965_fill_beacon_frame(struct iwl_priv *priv,
- struct ieee80211_hdr *hdr,
- const u8 *dest, int left)
+static unsigned int iwl_fill_beacon_frame(struct iwl_priv *priv,
+ struct ieee80211_hdr *hdr,
+ const u8 *dest, int left)
{
-
if (!iwl_is_associated(priv) || !priv->ibss_beacon ||
((priv->iw_mode != IEEE80211_IF_TYPE_IBSS) &&
(priv->iw_mode != IEEE80211_IF_TYPE_AP)))
return IWL_RATE_6M_PLCP;
}
+unsigned int iwl4965_hw_get_beacon_cmd(struct iwl_priv *priv,
+ struct iwl_frame *frame, u8 rate)
+{
+ struct iwl_tx_beacon_cmd *tx_beacon_cmd;
+ unsigned int frame_size;
+
+ tx_beacon_cmd = &frame->u.beacon;
+ memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd));
+
+ tx_beacon_cmd->tx.sta_id = priv->hw_params.bcast_sta_id;
+ tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;
+
+ frame_size = iwl_fill_beacon_frame(priv, tx_beacon_cmd->frame,
+ iwl_bcast_addr,
+ sizeof(frame->u) - sizeof(*tx_beacon_cmd));
+
+ BUG_ON(frame_size > MAX_MPDU_SIZE);
+ tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size);
+
+ if ((rate == IWL_RATE_1M_PLCP) || (rate >= IWL_RATE_2M_PLCP))
+ tx_beacon_cmd->tx.rate_n_flags =
+ iwl_hw_set_rate_n_flags(rate, RATE_MCS_CCK_MSK);
+ else
+ tx_beacon_cmd->tx.rate_n_flags =
+ iwl_hw_set_rate_n_flags(rate, 0);
+
+ tx_beacon_cmd->tx.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK |
+ TX_CMD_FLG_TSF_MSK |
+ TX_CMD_FLG_STA_RATE_MSK;
+
+ return sizeof(*tx_beacon_cmd) + frame_size;
+}
static int iwl4965_send_beacon_cmd(struct iwl_priv *priv)
{
struct iwl_frame *frame;
}
#define MAX_UCODE_BEACON_INTERVAL 4096
-#define INTEL_CONN_LISTEN_INTERVAL __constant_cpu_to_le16(0xA)
static __le16 iwl4965_adjust_beacon_interval(u16 beacon_val)
{
priv->rxon_timing.timestamp.dw[0] =
cpu_to_le32(priv->timestamp & 0xFFFFFFFF);
- priv->rxon_timing.listen_interval = INTEL_CONN_LISTEN_INTERVAL;
+ priv->rxon_timing.listen_interval = cpu_to_le16(conf->listen_interval);
tsf = priv->timestamp;
(IWL_OFDM_BASIC_RATES_MASK >> IWL_FIRST_OFDM_RATE) & 0xFF;
}
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
#include "iwl-spectrum.h"
static void iwl4965_rx_spectrum_measure_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl4965_spectrum_notification *report = &(pkt->u.spectrum_notif);
wake_up_interruptible(&priv->wait_command_queue);
}
+int iwl4965_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src)
+{
+ int ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ ret = iwl_grab_nic_access(priv);
+ if (ret)
+ goto err;
+
+ if (src == IWL_PWR_SRC_VAUX) {
+ u32 val;
+ ret = pci_read_config_dword(priv->pci_dev, PCI_POWER_SOURCE,
+ &val);
+
+ if (val & PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT)
+ iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
+ APMG_PS_CTRL_VAL_PWR_SRC_VAUX,
+ ~APMG_PS_CTRL_MSK_PWR_SRC);
+ } else {
+ iwl_set_bits_mask_prph(priv, APMG_PS_CTRL_REG,
+ APMG_PS_CTRL_VAL_PWR_SRC_VMAIN,
+ ~APMG_PS_CTRL_MSK_PWR_SRC);
+ }
+
+ iwl_release_nic_access(priv);
+err:
+ spin_unlock_irqrestore(&priv->lock, flags);
+ return ret;
+}
+
/**
* iwl4965_setup_rx_handlers - Initialize Rx handler callbacks
*
}
/* If platform's RF_KILL switch is NOT set to KILL */
- if (iwl_read32(priv, CSR_GP_CNTRL) &
- CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
+ if (iwl_read32(priv, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)
clear_bit(STATUS_RF_KILL_HW, &priv->status);
else
set_bit(STATUS_RF_KILL_HW, &priv->status);
- if (!test_bit(STATUS_IN_SUSPEND, &priv->status) &&
- iwl_is_rfkill(priv)) {
+ if (iwl_is_rfkill(priv)) {
+ iwl4965_enable_interrupts(priv);
IWL_WARNING("Radio disabled by %s RF Kill switch\n",
test_bit(STATUS_RF_KILL_HW, &priv->status) ? "HW" : "SW");
- return -ENODEV;
+ return 0;
}
iwl_write32(priv, CSR_INT, 0xFFFFFFFF);
memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
priv->ucode_data.len);
- /* We return success when we resume from suspend and rf_kill is on. */
- if (test_bit(STATUS_RF_KILL_HW, &priv->status) ||
- test_bit(STATUS_RF_KILL_SW, &priv->status))
- return 0;
-
for (i = 0; i < MAX_HW_RESTARTS; i++) {
iwl_clear_stations_table(priv);
unsigned long flags;
if (priv->iw_mode == IEEE80211_IF_TYPE_AP) {
- IWL_ERROR("%s Should not be called in AP mode\n", __FUNCTION__);
+ IWL_ERROR("%s Should not be called in AP mode\n", __func__);
return;
}
default:
IWL_ERROR("%s Should not be called in %d mode\n",
- __FUNCTION__, priv->iw_mode);
+ __func__, priv->iw_mode);
break;
}
if (ret)
goto out_release_irq;
+ if (iwl_is_rfkill(priv))
+ goto out;
+
IWL_DEBUG_INFO("Start UP work done.\n");
if (test_bit(STATUS_IN_SUSPEND, &priv->status))
}
}
+out:
priv->is_open = 1;
IWL_DEBUG_MAC80211("leave\n");
return 0;
{
struct iwl_priv *priv = hw->priv;
- IWL_DEBUG_MAC80211("enter\n");
+ IWL_DEBUG_MACDUMP("enter\n");
if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) {
IWL_DEBUG_MAC80211("leave - monitor\n");
if (iwl_tx_skb(priv, skb))
dev_kfree_skb_any(skb);
- IWL_DEBUG_MAC80211("leave\n");
+ IWL_DEBUG_MACDUMP("leave\n");
return 0;
}
spin_lock_irqsave(&priv->lock, flags);
+
/* if we are switching from ht to 2.4 clear flags
* from any ht related info since 2.4 does not
* support ht */
if (bss_conf->assoc) {
priv->assoc_id = bss_conf->aid;
priv->beacon_int = bss_conf->beacon_int;
+ priv->power_data.dtim_period = bss_conf->dtim_period;
priv->timestamp = bss_conf->timestamp;
priv->assoc_capability = bss_conf->assoc_capability;
priv->next_scan_jiffies = jiffies +
return 0;
}
+static int iwl4965_mac_ampdu_action(struct ieee80211_hw *hw,
+ enum ieee80211_ampdu_mlme_action action,
+ const u8 *addr, u16 tid, u16 *ssn)
+{
+ struct iwl_priv *priv = hw->priv;
+ DECLARE_MAC_BUF(mac);
+
+ IWL_DEBUG_HT("A-MPDU action on addr %s tid %d\n",
+ print_mac(mac, addr), tid);
+
+ if (!(priv->cfg->sku & IWL_SKU_N))
+ return -EACCES;
+
+ switch (action) {
+ case IEEE80211_AMPDU_RX_START:
+ IWL_DEBUG_HT("start Rx\n");
+ return iwl_rx_agg_start(priv, addr, tid, *ssn);
+ case IEEE80211_AMPDU_RX_STOP:
+ IWL_DEBUG_HT("stop Rx\n");
+ return iwl_rx_agg_stop(priv, addr, tid);
+ case IEEE80211_AMPDU_TX_START:
+ IWL_DEBUG_HT("start Tx\n");
+ return iwl_tx_agg_start(priv, addr, tid, ssn);
+ case IEEE80211_AMPDU_TX_STOP:
+ IWL_DEBUG_HT("stop Tx\n");
+ return iwl_tx_agg_stop(priv, addr, tid);
+ default:
+ IWL_DEBUG_HT("unknown\n");
+ return -EINVAL;
+ break;
+ }
+ return 0;
+}
static int iwl4965_mac_get_tx_stats(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats)
{
static DEVICE_ATTR(temperature, S_IRUGO, show_temperature, NULL);
-static ssize_t show_rs_window(struct device *d,
- struct device_attribute *attr,
- char *buf)
-{
- struct iwl_priv *priv = d->driver_data;
- return iwl4965_fill_rs_info(priv->hw, buf, IWL_AP_ID);
-}
-static DEVICE_ATTR(rs_window, S_IRUGO, show_rs_window, NULL);
-
static ssize_t show_tx_power(struct device *d,
struct device_attribute *attr, char *buf)
{
static DEVICE_ATTR(filter_flags, S_IWUSR | S_IRUGO, show_filter_flags,
store_filter_flags);
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
static ssize_t show_measurement(struct device *d,
struct device_attribute *attr, char *buf)
struct iwl_priv *priv = dev_get_drvdata(d);
struct iwl4965_spectrum_notification measure_report;
u32 size = sizeof(measure_report), len = 0, ofs = 0;
- u8 *data = (u8 *) & measure_report;
+ u8 *data = (u8 *)&measure_report;
unsigned long flags;
spin_lock_irqsave(&priv->lock, flags);
static DEVICE_ATTR(measurement, S_IRUSR | S_IWUSR,
show_measurement, store_measurement);
-#endif /* CONFIG_IWL4965_SPECTRUM_MEASUREMENT */
+#endif /* CONFIG_IWLAGN_SPECTRUM_MEASUREMENT */
static ssize_t store_retry_rate(struct device *d,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct iwl_priv *priv = dev_get_drvdata(d);
- int rc;
+ int ret;
int mode;
mode = simple_strtoul(buf, NULL, 0);
mutex_lock(&priv->mutex);
if (!iwl_is_ready(priv)) {
- rc = -EAGAIN;
+ ret = -EAGAIN;
goto out;
}
- rc = iwl_power_set_user_mode(priv, mode);
- if (rc) {
+ ret = iwl_power_set_user_mode(priv, mode);
+ if (ret) {
IWL_DEBUG_MAC80211("failed setting power mode.\n");
goto out;
}
- rc = count;
+ ret = count;
out:
mutex_unlock(&priv->mutex);
- return rc;
+ return ret;
}
-#define MAX_WX_STRING 80
-
-/* Values are in microsecond */
-static const s32 timeout_duration[] = {
- 350000,
- 250000,
- 75000,
- 37000,
- 25000,
-};
-static const s32 period_duration[] = {
- 400000,
- 700000,
- 1000000,
- 1000000,
- 1000000
-};
-
static ssize_t show_power_level(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
+ int mode = priv->power_data.user_power_setting;
+ int system = priv->power_data.system_power_setting;
int level = priv->power_data.power_mode;
char *p = buf;
- p += sprintf(p, "%d ", level);
- switch (level) {
- case IWL_POWER_MODE_CAM:
- case IWL_POWER_AC:
- p += sprintf(p, "(AC)");
+ switch (system) {
+ case IWL_POWER_SYS_AUTO:
+ p += sprintf(p, "SYSTEM:auto");
break;
- case IWL_POWER_BATTERY:
- p += sprintf(p, "(BATTERY)");
+ case IWL_POWER_SYS_AC:
+ p += sprintf(p, "SYSTEM:ac");
+ break;
+ case IWL_POWER_SYS_BATTERY:
+ p += sprintf(p, "SYSTEM:battery");
break;
- default:
- p += sprintf(p,
- "(Timeout %dms, Period %dms)",
- timeout_duration[level - 1] / 1000,
- period_duration[level - 1] / 1000);
}
-/*
- if (!(priv->power_mode & IWL_POWER_ENABLED))
- p += sprintf(p, " OFF\n");
- else
- p += sprintf(p, " \n");
-*/
- p += sprintf(p, " \n");
- return (p - buf + 1);
+
+ p += sprintf(p, "\tMODE:%s", (mode < IWL_POWER_AUTO)?"fixed":"auto");
+ p += sprintf(p, "\tINDEX:%d", level);
+ p += sprintf(p, "\n");
+ return p - buf + 1;
}
static DEVICE_ATTR(power_level, S_IWUSR | S_IRUSR, show_power_level,
struct iwl_priv *priv = dev_get_drvdata(d);
u32 size = sizeof(struct iwl_notif_statistics);
u32 len = 0, ofs = 0;
- u8 *data = (u8 *) & priv->statistics;
+ u8 *data = (u8 *)&priv->statistics;
int rc = 0;
if (!iwl_is_alive(priv))
&dev_attr_channels.attr,
&dev_attr_flags.attr,
&dev_attr_filter_flags.attr,
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
&dev_attr_measurement.attr,
#endif
&dev_attr_power_level.attr,
&dev_attr_retry_rate.attr,
- &dev_attr_rs_window.attr,
&dev_attr_statistics.attr,
&dev_attr_status.attr,
&dev_attr_temperature.attr,
/* Hardware specific file defines the PCI IDs table for that hardware module */
static struct pci_device_id iwl_hw_card_ids[] = {
+#ifdef CONFIG_IWL4965
{IWL_PCI_DEVICE(0x4229, PCI_ANY_ID, iwl4965_agn_cfg)},
{IWL_PCI_DEVICE(0x4230, PCI_ANY_ID, iwl4965_agn_cfg)},
+#endif /* CONFIG_IWL4965 */
#ifdef CONFIG_IWL5000
{IWL_PCI_DEVICE(0x4232, 0x1205, iwl5100_bg_cfg)},
{IWL_PCI_DEVICE(0x4232, 0x1305, iwl5100_bg_cfg)},
printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n");
printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n");
- ret = iwl4965_rate_control_register();
+ ret = iwlagn_rate_control_register();
if (ret) {
IWL_ERROR("Unable to register rate control algorithm: %d\n", ret);
return ret;
return ret;
error_register:
- iwl4965_rate_control_unregister();
+ iwlagn_rate_control_unregister();
return ret;
}
static void __exit iwl4965_exit(void)
{
pci_unregister_driver(&iwl_driver);
- iwl4965_rate_control_unregister();
+ iwlagn_rate_control_unregister();
}
module_exit(iwl4965_exit);
__le16 reserved;
} __attribute__ ((packed));
-
-
+#define IWL_CONN_MAX_LISTEN_INTERVAL 10
/*
* REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
} __attribute__ ((packed));
/* Fixed (non-configurable) rx data from phy */
-#define RX_PHY_FLAGS_ANTENNAE_OFFSET (4)
-#define RX_PHY_FLAGS_ANTENNAE_MASK (0x70)
-#define IWL_AGC_DB_MASK (0x3f80) /* MASK(7,13) */
-#define IWL_AGC_DB_POS (7)
+
+#define IWL49_RX_RES_PHY_CNT 14
+#define IWL49_RX_PHY_FLAGS_ANTENNAE_OFFSET (4)
+#define IWL49_RX_PHY_FLAGS_ANTENNAE_MASK (0x70)
+#define IWL49_AGC_DB_MASK (0x3f80) /* MASK(7,13) */
+#define IWL49_AGC_DB_POS (7)
struct iwl4965_rx_non_cfg_phy {
__le16 ant_selection; /* ant A bit 4, ant B bit 5, ant C bit 6 */
__le16 agc_info; /* agc code 0:6, agc dB 7:13, reserved 14:15 */
u8 pad[0];
} __attribute__ ((packed));
+
+#define IWL50_RX_RES_PHY_CNT 8
+#define IWL50_RX_RES_AGC_IDX 1
+#define IWL50_RX_RES_RSSI_AB_IDX 2
+#define IWL50_RX_RES_RSSI_C_IDX 3
+#define IWL50_OFDM_AGC_MSK 0xfe00
+#define IWL50_OFDM_AGC_BIT_POS 9
+#define IWL50_OFDM_RSSI_A_MSK 0x00ff
+#define IWL50_OFDM_RSSI_A_BIT_POS 0
+#define IWL50_OFDM_RSSI_B_MSK 0xff0000
+#define IWL50_OFDM_RSSI_B_BIT_POS 16
+#define IWL50_OFDM_RSSI_C_MSK 0x00ff
+#define IWL50_OFDM_RSSI_C_BIT_POS 0
+
+struct iwl5000_non_cfg_phy {
+ __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* upto 8 phy entries */
+} __attribute__ ((packed));
+
+
/*
* REPLY_RX = 0xc3 (response only, not a command)
* Used only for legacy (non 11n) frames.
*/
-#define RX_RES_PHY_CNT 14
-struct iwl4965_rx_phy_res {
+struct iwl_rx_phy_res {
u8 non_cfg_phy_cnt; /* non configurable DSP phy data byte count */
u8 cfg_phy_cnt; /* configurable DSP phy data byte count */
u8 stat_id; /* configurable DSP phy data set ID */
__le32 beacon_time_stamp; /* beacon at on-air rise */
__le16 phy_flags; /* general phy flags: band, modulation, ... */
__le16 channel; /* channel number */
- __le16 non_cfg_phy[RX_RES_PHY_CNT]; /* upto 14 phy entries */
- __le32 reserved2;
+ u8 non_cfg_phy_buf[32]; /* for various implementations of non_cfg_phy */
__le32 rate_n_flags; /* RATE_MCS_* */
__le16 byte_count; /* frame's byte-count */
__le16 reserved3;
*****************************************************************************/
/**
- * struct iwl4965_powertable_cmd - Power Table Command
+ * struct iwl_powertable_cmd - Power Table Command
* @flags: See below:
*
* POWER_TABLE_CMD = 0x77 (command, has simple generic response)
#define IWL_POWER_PCI_PM_MSK __constant_cpu_to_le16(1 << 3)
#define IWL_POWER_FAST_PD __constant_cpu_to_le16(1 << 4)
-struct iwl4965_powertable_cmd {
+struct iwl_powertable_cmd {
__le16 flags;
u8 keep_alive_seconds;
u8 debug_flags;
/*
* REPLY_TX_BEACON = 0x91 (command, has simple generic response)
*/
-struct iwl4965_tx_beacon_cmd {
+struct iwl_tx_beacon_cmd {
struct iwl_tx_cmd tx;
__le16 tim_idx;
u8 tim_size;
}
EXPORT_SYMBOL(iwl_reset_qos);
-#define MAX_BIT_RATE_40_MHZ 0x96; /* 150 Mbps */
-#define MAX_BIT_RATE_20_MHZ 0x48; /* 72 Mbps */
+#define MAX_BIT_RATE_40_MHZ 0x96 /* 150 Mbps */
+#define MAX_BIT_RATE_20_MHZ 0x48 /* 72 Mbps */
static void iwlcore_init_ht_hw_capab(const struct iwl_priv *priv,
struct ieee80211_ht_info *ht_info,
enum ieee80211_band band)
{
int ret;
struct ieee80211_hw *hw = priv->hw;
- hw->rate_control_algorithm = "iwl-4965-rs";
+ hw->rate_control_algorithm = "iwl-agn-rs";
/* Tell mac80211 our characteristics */
- hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
- IEEE80211_HW_SIGNAL_DBM |
+ hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM;
/* Default value; 4 EDCA QOS priorities */
hw->queues = 4;
hw->ampdu_queues = priv->cfg->mod_params->num_of_ampdu_queues;
hw->conf.beacon_int = 100;
+ hw->max_listen_interval = IWL_CONN_MAX_LISTEN_INTERVAL;
if (priv->bands[IEEE80211_BAND_2GHZ].n_channels)
priv->hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
void (*chain_noise_reset)(struct iwl_priv *priv);
void (*rts_tx_cmd_flag)(struct ieee80211_tx_info *info,
__le32 *tx_flags);
+ int (*calc_rssi)(struct iwl_priv *priv,
+ struct iwl_rx_phy_res *rx_resp);
};
struct iwl_lib_ops {
int (*set_pwr_src)(struct iwl_priv *priv, enum iwl_pwr_src src);
} apm_ops;
/* power */
- int (*set_power)(struct iwl_priv *priv, void *cmd);
int (*send_tx_power) (struct iwl_priv *priv);
void (*update_chain_flags)(struct iwl_priv *priv);
void (*temperature) (struct iwl_priv *priv);
* 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
*/
#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
+#define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240)
/* Bits for CSR_HW_IF_CONFIG_REG */
#define CSR49_HW_IF_CONFIG_REG_BIT_4965_R (0x00000010)
#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000)
#define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000)
-#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
+#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000)
+#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
+#define CSR_HW_IF_CONFIG_REG_BIT_PCI_OWN_SEM (0x00400000)
+#define CSR_HW_IF_CONFIG_REG_BIT_ME_OWN (0x02000000)
+#define CSR_HW_IF_CONFIG_REG_BIT_WAKE_ME (0x08000000)
+
/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
* acknowledged (reset) by host writing "1" to flagged bits. */
#define CSR39_ANA_PLL_CFG_VAL (0x01000000)
#define CSR50_ANA_PLL_CFG_VAL (0x00880300)
+/* HPET MEM debug */
+#define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000)
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
/*
#define IWL_DEBUG(level, fmt, args...) \
do { if (priv->debug_level & (level)) \
dev_printk(KERN_ERR, &(priv->hw->wiphy->dev), "%c %s " fmt, \
- in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0)
+ in_interrupt() ? 'I' : 'U', __func__ , ## args); } while (0)
#define IWL_DEBUG_LIMIT(level, fmt, args...) \
do { if ((priv->debug_level & (level)) && net_ratelimit()) \
dev_printk(KERN_ERR, &(priv->hw->wiphy->dev), "%c %s " fmt, \
- in_interrupt() ? 'I' : 'U', __FUNCTION__ , ## args); } while (0)
+ in_interrupt() ? 'I' : 'U', __func__ , ## args); } while (0)
#ifdef CONFIG_IWLWIFI_DEBUGFS
struct iwl_debugfs {
#endif
#else
-static inline void IWL_DEBUG(int level, const char *fmt, ...)
-{
-}
-static inline void IWL_DEBUG_LIMIT(int level, const char *fmt, ...)
-{
-}
+#define IWL_DEBUG(level, fmt, args...)
+#define IWL_DEBUG_LIMIT(level, fmt, args...)
#endif /* CONFIG_IWLWIFI_DEBUG */
#define IWL_DL_MAC80211 (1 << 1)
#define IWL_DL_HOST_COMMAND (1 << 2)
#define IWL_DL_STATE (1 << 3)
-
+#define IWL_DL_MACDUMP (1 << 4)
#define IWL_DL_RADIO (1 << 7)
#define IWL_DL_POWER (1 << 8)
#define IWL_DL_TEMP (1 << 9)
#define IWL_DEBUG_INFO(f, a...) IWL_DEBUG(IWL_DL_INFO, f, ## a)
#define IWL_DEBUG_MAC80211(f, a...) IWL_DEBUG(IWL_DL_MAC80211, f, ## a)
+#define IWL_DEBUG_MACDUMP(f, a...) IWL_DEBUG(IWL_DL_MACDUMP, f, ## a)
#define IWL_DEBUG_TEMP(f, a...) IWL_DEBUG(IWL_DL_TEMP, f, ## a)
#define IWL_DEBUG_SCAN(f, a...) IWL_DEBUG(IWL_DL_SCAN, f, ## a)
#define IWL_DEBUG_RX(f, a...) IWL_DEBUG(IWL_DL_RX, f, ## a)
DECLARE_MAC_BUF(mac);
buf = kmalloc(bufsz, GFP_KERNEL);
- if(!buf)
+ if (!buf)
return -ENOMEM;
pos += scnprintf(buf + pos, bufsz - pos, "num of stations: %d\n\n",
{
struct iwl_debugfs *dbgfs;
struct dentry *phyd = priv->hw->wiphy->debugfsdir;
+ int ret = 0;
dbgfs = kzalloc(sizeof(struct iwl_debugfs), GFP_KERNEL);
if (!dbgfs) {
+ ret = -ENOMEM;
goto err;
}
priv->dbgfs = dbgfs;
dbgfs->name = name;
dbgfs->dir_drv = debugfs_create_dir(name, phyd);
- if (!dbgfs->dir_drv || IS_ERR(dbgfs->dir_drv)){
+ if (!dbgfs->dir_drv || IS_ERR(dbgfs->dir_drv)) {
+ ret = -ENOENT;
goto err;
}
err:
IWL_ERROR("Can't open the debugfs directory\n");
iwl_dbgfs_unregister(priv);
- return -ENOENT;
+ return ret;
}
EXPORT_SYMBOL(iwl_dbgfs_register);
*/
void iwl_dbgfs_unregister(struct iwl_priv *priv)
{
- if (!(priv->dbgfs))
+ if (!priv->dbgfs)
return;
DEBUGFS_REMOVE(priv->dbgfs->dbgfs_data_files.file_eeprom);
#include <linux/kernel.h>
#include <net/ieee80211_radiotap.h>
-#define DRV_NAME "iwl4965"
+#define DRV_NAME "iwlagn"
#include "iwl-rfkill.h"
#include "iwl-eeprom.h"
#include "iwl-4965-hw.h"
#include "iwl-debug.h"
#include "iwl-led.h"
#include "iwl-power.h"
+#include "iwl-agn-rs.h"
/* configuration for the iwl4965 */
extern struct iwl_cfg iwl4965_agn_cfg;
struct iwl_tx_queue {
struct iwl_queue q;
struct iwl_tfd_frame *bd;
- struct iwl_cmd *cmd;
- dma_addr_t dma_addr_cmd;
+ struct iwl_cmd *cmd[TFD_TX_CMD_SLOTS];
struct iwl_tx_info *txb;
int need_update;
int sched_retry;
const s8 clip_powers[IWL_MAX_RATES];
};
-#include "iwl-4965-rs.h"
#define IWL_TX_FIFO_AC0 0
#define IWL_TX_FIFO_AC1 1
struct iwl_frame {
union {
struct ieee80211_hdr frame;
- struct iwl4965_tx_beacon_cmd beacon;
+ struct iwl_tx_beacon_cmd beacon;
u8 raw[IEEE80211_FRAME_LEN];
u8 cmd[360];
} u;
u32 val32;
struct iwl4965_bt_cmd bt;
struct iwl4965_rxon_time_cmd rxon_time;
- struct iwl4965_powertable_cmd powertable;
+ struct iwl_powertable_cmd powertable;
struct iwl_qosparam_cmd qosparam;
struct iwl_tx_cmd tx;
- struct iwl4965_tx_beacon_cmd tx_beacon;
struct iwl4965_rxon_assoc_cmd rxon_assoc;
struct iwl_rem_sta_cmd rm_sta;
u8 *indirect;
const u8 *dest, int left);
extern void iwl4965_update_chain_flags(struct iwl_priv *priv);
int iwl4965_set_pwr_src(struct iwl_priv *priv, enum iwl_pwr_src src);
+extern int iwl4965_set_power(struct iwl_priv *priv, void *cmd);
extern const u8 iwl_bcast_addr[ETH_ALEN];
* Forward declare iwl-4965.c functions for iwl-base.c
*/
extern void iwl4965_rf_kill_ct_config(struct iwl_priv *priv);
-
-int iwl4965_mac_ampdu_action(struct ieee80211_hw *hw,
- enum ieee80211_ampdu_mlme_action action,
- const u8 *addr, u16 tid, u16 *ssn);
int iwl4965_check_empty_hw_queue(struct iwl_priv *priv, int sta_id,
u8 tid, int txq_id);
#define EEPROM_SEM_RETRY_LIMIT 1000 /* number of attempts (not time) */
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
-
enum {
MEASUREMENT_READY = (1 << 0),
MEASUREMENT_ACTIVE = (1 << 1),
};
-#endif
#define IWL_MAX_NUM_QUEUES 20 /* FIXME: do dynamic allocation */
struct ieee80211_supported_band bands[IEEE80211_NUM_BANDS];
-#ifdef CONFIG_IWL4965_SPECTRUM_MEASUREMENT
+#ifdef CONFIG_IWLAGN_SPECTRUM_MEASUREMENT
/* spectrum measurement report caching */
struct iwl4965_spectrum_notification measure_report;
u8 measurement_status;
void iwl_eeprom_free(struct iwl_priv *priv)
{
- if(priv->eeprom)
- kfree(priv->eeprom);
+ kfree(priv->eeprom);
priv->eeprom = NULL;
}
EXPORT_SYMBOL(iwl_eeprom_free);
* TX cmd queue. Otherwise in case the cmd comes
* in later, it will possibly set an invalid
* address (cmd->meta.source). */
- qcmd = &priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_idx];
+ qcmd = priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_idx];
qcmd->meta.flags &= ~CMD_WANT_SKB;
}
fail:
/* Set led register off */
static int iwl4965_led_off_reg(struct iwl_priv *priv, int led_id)
{
- IWL_DEBUG_LED("radio off\n");
+ IWL_DEBUG_LED("LED Reg off\n");
iwl_write32(priv, CSR_LED_REG, CSR_LED_REG_TRUN_OFF);
return 0;
}
+/*
+ * Set led register in case of disassociation according to rfkill state
+ */
+static int iwl_led_associate(struct iwl_priv *priv, int led_id)
+{
+ IWL_DEBUG_LED("Associated\n");
+ priv->allow_blinking = 1;
+ return iwl4965_led_on_reg(priv, led_id);
+}
+static int iwl_led_disassociate(struct iwl_priv *priv, int led_id)
+{
+ priv->allow_blinking = 0;
+ if (iwl_is_rfkill(priv))
+ iwl4965_led_off_reg(priv, led_id);
+ else
+ iwl4965_led_on_reg(priv, led_id);
+
+ return 0;
+}
+
/*
* brightness call back function for Tx/Rx LED
*/
led_type_str[led->type], brightness);
switch (brightness) {
case LED_FULL:
- if (led->type == IWL_LED_TRG_ASSOC)
- priv->allow_blinking = 1;
-
if (led->led_on)
led->led_on(priv, IWL_LED_LINK);
break;
case LED_OFF:
- if (led->type == IWL_LED_TRG_ASSOC)
- priv->allow_blinking = 0;
-
if (led->led_off)
led->led_off(priv, IWL_LED_LINK);
break;
*/
static int iwl_leds_register_led(struct iwl_priv *priv, struct iwl_led *led,
enum led_type type, u8 set_led,
- const char *name, char *trigger)
+ char *trigger)
{
struct device *device = wiphy_dev(priv->hw->wiphy);
int ret;
- led->led_dev.name = name;
+ led->led_dev.name = led->name;
led->led_dev.brightness_set = iwl_led_brightness_set;
led->led_dev.default_trigger = trigger;
if (tpt < 0) /* wrapparound */
tpt = -tpt;
- IWL_DEBUG_LED("tpt %lld current_tpt %lld\n", tpt, current_tpt);
+ IWL_DEBUG_LED("tpt %lld current_tpt %llu\n",
+ (long long)tpt,
+ (unsigned long long)current_tpt);
priv->led_tpt = current_tpt;
if (!priv->allow_blinking)
return i;
}
-static inline int is_rf_kill(struct iwl_priv *priv)
-{
- return test_bit(STATUS_RF_KILL_HW, &priv->status) ||
- test_bit(STATUS_RF_KILL_SW, &priv->status);
-}
-
/*
* this function called from handler. Since setting Led command can
* happen very frequent we postpone led command to be called from
priv->last_blink_time = 0;
return;
}
- if (is_rf_kill(priv)) {
+ if (iwl_is_rfkill(priv)) {
priv->last_blink_time = 0;
return;
}
int iwl_leds_register(struct iwl_priv *priv)
{
char *trigger;
- char name[32];
int ret;
priv->last_blink_rate = 0;
priv->allow_blinking = 0;
trigger = ieee80211_get_radio_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:radio",
+ snprintf(priv->led[IWL_LED_TRG_RADIO].name,
+ sizeof(priv->led[IWL_LED_TRG_RADIO].name), "iwl-%s:radio",
wiphy_name(priv->hw->wiphy));
priv->led[IWL_LED_TRG_RADIO].led_on = iwl4965_led_on_reg;
priv->led[IWL_LED_TRG_RADIO].led_pattern = NULL;
ret = iwl_leds_register_led(priv, &priv->led[IWL_LED_TRG_RADIO],
- IWL_LED_TRG_RADIO, 1, name, trigger);
+ IWL_LED_TRG_RADIO, 1, trigger);
if (ret)
goto exit_fail;
trigger = ieee80211_get_assoc_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:assoc",
+ snprintf(priv->led[IWL_LED_TRG_ASSOC].name,
+ sizeof(priv->led[IWL_LED_TRG_ASSOC].name), "iwl-%s:assoc",
wiphy_name(priv->hw->wiphy));
ret = iwl_leds_register_led(priv, &priv->led[IWL_LED_TRG_ASSOC],
- IWL_LED_TRG_ASSOC, 0, name, trigger);
+ IWL_LED_TRG_ASSOC, 0, trigger);
/* for assoc always turn led on */
- priv->led[IWL_LED_TRG_ASSOC].led_on = iwl4965_led_on_reg;
- priv->led[IWL_LED_TRG_ASSOC].led_off = iwl4965_led_on_reg;
+ priv->led[IWL_LED_TRG_ASSOC].led_on = iwl_led_associate;
+ priv->led[IWL_LED_TRG_ASSOC].led_off = iwl_led_disassociate;
priv->led[IWL_LED_TRG_ASSOC].led_pattern = NULL;
if (ret)
goto exit_fail;
trigger = ieee80211_get_rx_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:RX", wiphy_name(priv->hw->wiphy));
-
+ snprintf(priv->led[IWL_LED_TRG_RX].name,
+ sizeof(priv->led[IWL_LED_TRG_RX].name), "iwl-%s:RX",
+ wiphy_name(priv->hw->wiphy));
ret = iwl_leds_register_led(priv, &priv->led[IWL_LED_TRG_RX],
- IWL_LED_TRG_RX, 0, name, trigger);
+ IWL_LED_TRG_RX, 0, trigger);
priv->led[IWL_LED_TRG_RX].led_on = iwl_led_associated;
priv->led[IWL_LED_TRG_RX].led_off = iwl_led_associated;
goto exit_fail;
trigger = ieee80211_get_tx_led_name(priv->hw);
- snprintf(name, sizeof(name), "iwl-%s:TX", wiphy_name(priv->hw->wiphy));
+ snprintf(priv->led[IWL_LED_TRG_TX].name,
+ sizeof(priv->led[IWL_LED_TRG_TX].name), "iwl-%s:TX",
+ wiphy_name(priv->hw->wiphy));
+
ret = iwl_leds_register_led(priv, &priv->led[IWL_LED_TRG_TX],
- IWL_LED_TRG_TX, 0, name, trigger);
+ IWL_LED_TRG_TX, 0, trigger);
priv->led[IWL_LED_TRG_TX].led_on = iwl_led_associated;
priv->led[IWL_LED_TRG_TX].led_off = iwl_led_associated;
struct iwl_led {
struct iwl_priv *priv;
struct led_classdev led_dev;
+ char name[32];
int (*led_on) (struct iwl_priv *priv, int led_id);
int (*led_off) (struct iwl_priv *priv, int led_id);
/* default power management (not Tx power) table values */
/* for tim 0-10 */
-static struct iwl_power_vec_entry range_0[IWL_POWER_AC] = {
+static struct iwl_power_vec_entry range_0[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 2, 2, 0xFF)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(300), SLP_VEC(1, 2, 2, 2, 0xFF)}, 0},
/* for tim = 3-10 */
-static struct iwl_power_vec_entry range_1[IWL_POWER_AC] = {
+static struct iwl_power_vec_entry range_1[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 3, 4, 4)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(300), SLP_VEC(1, 2, 3, 4, 7)}, 0},
};
/* for tim > 11 */
-static struct iwl_power_vec_entry range_2[IWL_POWER_AC] = {
+static struct iwl_power_vec_entry range_2[IWL_POWER_MAX] = {
{{NOSLP, SLP_TOUT(0), SLP_TOUT(0), SLP_VEC(0, 0, 0, 0, 0)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(500), SLP_VEC(1, 2, 3, 4, 0xFF)}, 0},
{{SLP, SLP_TOUT(200), SLP_TOUT(300), SLP_VEC(2, 4, 6, 7, 0xFF)}, 0},
{{SLP, SLP_TOUT(25), SLP_TOUT(25), SLP_VEC(4, 7, 10, 10, 0xFF)}, 0}
};
+/* set card power command */
+static int iwl_set_power(struct iwl_priv *priv, void *cmd)
+{
+ return iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
+ sizeof(struct iwl_powertable_cmd),
+ cmd, NULL);
+}
/* decide the right power level according to association status
* and battery status
*/
static u16 iwl_get_auto_power_mode(struct iwl_priv *priv)
{
- u16 mode = priv->power_data.user_power_setting;
+ u16 mode;
switch (priv->power_data.user_power_setting) {
case IWL_POWER_AUTO:
else
mode = IWL_POWER_ON_AC_DISASSOC;
break;
+ /* FIXME: remove battery and ac from here */
case IWL_POWER_BATTERY:
mode = IWL_POWER_INDEX_3;
break;
case IWL_POWER_AC:
mode = IWL_POWER_MODE_CAM;
break;
+ default:
+ mode = priv->power_data.user_power_setting;
+ break;
}
return mode;
}
{
int ret = 0, i;
struct iwl_power_mgr *pow_data;
- int size = sizeof(struct iwl_power_vec_entry) * IWL_POWER_AC;
+ int size = sizeof(struct iwl_power_vec_entry) * IWL_POWER_MAX;
u16 pci_pm;
IWL_DEBUG_POWER("Initialize power \n");
if (ret != 0)
return 0;
else {
- struct iwl4965_powertable_cmd *cmd;
+ struct iwl_powertable_cmd *cmd;
IWL_DEBUG_POWER("adjust power command flags\n");
- for (i = 0; i < IWL_POWER_AC; i++) {
+ for (i = 0; i < IWL_POWER_MAX; i++) {
cmd = &pow_data->pwr_range_0[i].cmd;
if (pci_pm & 0x1)
/* adjust power command according to dtim period and power level*/
static int iwl_update_power_command(struct iwl_priv *priv,
- struct iwl4965_powertable_cmd *cmd,
+ struct iwl_powertable_cmd *cmd,
u16 mode)
{
int ret = 0, i;
range = &pow_data->pwr_range_2[0];
period = pow_data->dtim_period;
- memcpy(cmd, &range[mode].cmd, sizeof(struct iwl4965_powertable_cmd));
+ memcpy(cmd, &range[mode].cmd, sizeof(struct iwl_powertable_cmd));
if (period == 0) {
period = 1;
* else user level */
switch (setting->system_power_setting) {
- case IWL_POWER_AUTO:
+ case IWL_POWER_SYS_AUTO:
final_mode = iwl_get_auto_power_mode(priv);
break;
- case IWL_POWER_BATTERY:
+ case IWL_POWER_SYS_BATTERY:
final_mode = IWL_POWER_INDEX_3;
break;
- case IWL_POWER_AC:
+ case IWL_POWER_SYS_AC:
final_mode = IWL_POWER_MODE_CAM;
break;
default:
- final_mode = setting->system_power_setting;
+ final_mode = IWL_POWER_INDEX_3;
+ WARN_ON(1);
}
if (setting->critical_power_setting > final_mode)
if (!iwl_is_rfkill(priv) && !setting->power_disabled &&
((setting->power_mode != final_mode) || refresh)) {
- struct iwl4965_powertable_cmd cmd;
+ struct iwl_powertable_cmd cmd;
if (final_mode != IWL_POWER_MODE_CAM)
set_bit(STATUS_POWER_PMI, &priv->status);
if (final_mode == IWL_POWER_INDEX_5)
cmd.flags |= IWL_POWER_FAST_PD;
- if (priv->cfg->ops->lib->set_power)
- ret = priv->cfg->ops->lib->set_power(priv, &cmd);
+ ret = iwl_set_power(priv, &cmd);
if (final_mode == IWL_POWER_MODE_CAM)
clear_bit(STATUS_POWER_PMI, &priv->status);
iwl_power_init_handle(priv);
priv->power_data.user_power_setting = IWL_POWER_AUTO;
priv->power_data.power_disabled = 0;
- priv->power_data.system_power_setting = IWL_POWER_AUTO;
+ priv->power_data.system_power_setting = IWL_POWER_SYS_AUTO;
priv->power_data.is_battery_active = 0;
priv->power_data.power_disabled = 0;
priv->power_data.critical_power_setting = 0;
struct iwl_priv;
-#define IWL_POWER_MODE_CAM 0x00 /* Continuously Aware Mode, always on */
-#define IWL_POWER_INDEX_3 0x03
-#define IWL_POWER_INDEX_5 0x05
-#define IWL_POWER_AC 0x06
-#define IWL_POWER_BATTERY 0x07
-#define IWL_POWER_AUTO 0x08
+enum {
+ IWL_POWER_MODE_CAM, /* Continuously Aware Mode, always on */
+ IWL_POWER_INDEX_1,
+ IWL_POWER_INDEX_2,
+ IWL_POWER_INDEX_3,
+ IWL_POWER_INDEX_4,
+ IWL_POWER_INDEX_5,
+ IWL_POWER_AUTO,
+ IWL_POWER_MAX = IWL_POWER_AUTO,
+ IWL_POWER_AC,
+ IWL_POWER_BATTERY,
+};
+
+enum {
+ IWL_POWER_SYS_AUTO,
+ IWL_POWER_SYS_AC,
+ IWL_POWER_SYS_BATTERY,
+};
+
#define IWL_POWER_LIMIT 0x08
#define IWL_POWER_MASK 0x0F
#define IWL_POWER_ENABLED 0x10
/* Power management (not Tx power) structures */
struct iwl_power_vec_entry {
- struct iwl4965_powertable_cmd cmd;
+ struct iwl_powertable_cmd cmd;
u8 no_dtim;
};
struct iwl_power_mgr {
spinlock_t lock;
- struct iwl_power_vec_entry pwr_range_0[IWL_POWER_AC];
- struct iwl_power_vec_entry pwr_range_1[IWL_POWER_AC];
- struct iwl_power_vec_entry pwr_range_2[IWL_POWER_AC];
+ struct iwl_power_vec_entry pwr_range_0[IWL_POWER_MAX];
+ struct iwl_power_vec_entry pwr_range_1[IWL_POWER_MAX];
+ struct iwl_power_vec_entry pwr_range_2[IWL_POWER_MAX];
u32 dtim_period;
/* final power level that used to calculate final power command */
u8 power_mode;
#define APMG_CLK_VAL_DMA_CLK_RQT (0x00000200)
#define APMG_CLK_VAL_BSM_CLK_RQT (0x00000800)
-#define APMG_PS_CTRL_VAL_RESET_REQ (0x04000000)
-#define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800)
+#define APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS (0x00400000)
+#define APMG_PS_CTRL_VAL_RESET_REQ (0x04000000)
+#define APMG_PS_CTRL_MSK_PWR_SRC (0x03000000)
+#define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN (0x00000000)
+#define APMG_PS_CTRL_VAL_PWR_SRC_MAX (0x01000000) /* 3945 only */
+#define APMG_PS_CTRL_VAL_PWR_SRC_VAUX (0x02000000)
-#define APMG_PS_CTRL_MSK_PWR_SRC (0x03000000)
-#define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN (0x00000000)
-#define APMG_PS_CTRL_VAL_PWR_SRC_VAUX (0x01000000)
+#define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800)
/**
* BSM (Bootstrap State Machine)
static void iwl_add_radiotap(struct iwl_priv *priv,
struct sk_buff *skb,
- struct iwl4965_rx_phy_res *rx_start,
+ struct iwl_rx_phy_res *rx_start,
struct ieee80211_rx_status *stats,
u32 ampdu_status)
{
struct ieee80211_rx_status *stats)
{
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
- struct iwl4965_rx_phy_res *rx_start = (include_phy) ?
- (struct iwl4965_rx_phy_res *)&(pkt->u.raw[0]) : NULL;
+ struct iwl_rx_phy_res *rx_start = (include_phy) ?
+ (struct iwl_rx_phy_res *)&(pkt->u.raw[0]) : NULL;
struct ieee80211_hdr *hdr;
u16 len;
__le32 *rx_end;
u32 ampdu_status_legacy;
if (!include_phy && priv->last_phy_res[0])
- rx_start = (struct iwl4965_rx_phy_res *)&priv->last_phy_res[1];
+ rx_start = (struct iwl_rx_phy_res *)&priv->last_phy_res[1];
if (!rx_start) {
IWL_ERROR("MPDU frame without a PHY data\n");
len = le16_to_cpu(rx_start->byte_count);
- rx_end = (__le32 *) ((u8 *) &pkt->u.raw[0] +
- sizeof(struct iwl4965_rx_phy_res) +
+ rx_end = (__le32 *)((u8 *) &pkt->u.raw[0] +
+ sizeof(struct iwl_rx_phy_res) +
rx_start->cfg_phy_cnt + len);
} else {
}
/* Calc max signal level (dBm) among 3 possible receivers */
-static int iwl_calc_rssi(struct iwl_priv *priv,
- struct iwl4965_rx_phy_res *rx_resp)
+static inline int iwl_calc_rssi(struct iwl_priv *priv,
+ struct iwl_rx_phy_res *rx_resp)
{
- /* data from PHY/DSP regarding signal strength, etc.,
- * contents are always there, not configurable by host. */
- struct iwl4965_rx_non_cfg_phy *ncphy =
- (struct iwl4965_rx_non_cfg_phy *)rx_resp->non_cfg_phy;
- u32 agc = (le16_to_cpu(ncphy->agc_info) & IWL_AGC_DB_MASK)
- >> IWL_AGC_DB_POS;
-
- u32 valid_antennae =
- (le16_to_cpu(rx_resp->phy_flags) & RX_PHY_FLAGS_ANTENNAE_MASK)
- >> RX_PHY_FLAGS_ANTENNAE_OFFSET;
- u8 max_rssi = 0;
- u32 i;
-
- /* Find max rssi among 3 possible receivers.
- * These values are measured by the digital signal processor (DSP).
- * They should stay fairly constant even as the signal strength varies,
- * if the radio's automatic gain control (AGC) is working right.
- * AGC value (see below) will provide the "interesting" info. */
- for (i = 0; i < 3; i++)
- if (valid_antennae & (1 << i))
- max_rssi = max(ncphy->rssi_info[i << 1], max_rssi);
-
- IWL_DEBUG_STATS("Rssi In A %d B %d C %d Max %d AGC dB %d\n",
- ncphy->rssi_info[0], ncphy->rssi_info[2], ncphy->rssi_info[4],
- max_rssi, agc);
-
- /* dBm = max_rssi dB - agc dB - constant.
- * Higher AGC (higher radio gain) means lower signal. */
- return max_rssi - agc - IWL_RSSI_OFFSET;
+ return priv->cfg->ops->utils->calc_rssi(priv, rx_resp);
}
+
static void iwl_sta_modify_ps_wake(struct iwl_priv *priv, int sta_id)
{
unsigned long flags;
* this rx packet for legacy frames,
* or phy data cached from REPLY_RX_PHY_CMD for HT frames. */
int include_phy = (pkt->hdr.cmd == REPLY_RX);
- struct iwl4965_rx_phy_res *rx_start = (include_phy) ?
- (struct iwl4965_rx_phy_res *)&(pkt->u.raw[0]) :
- (struct iwl4965_rx_phy_res *)&priv->last_phy_res[1];
+ struct iwl_rx_phy_res *rx_start = (include_phy) ?
+ (struct iwl_rx_phy_res *)&(pkt->u.raw[0]) :
+ (struct iwl_rx_phy_res *)&priv->last_phy_res[1];
__le32 *rx_end;
unsigned int len = 0;
u16 fc;
if (!include_phy) {
if (priv->last_phy_res[0])
- rx_start = (struct iwl4965_rx_phy_res *)
+ rx_start = (struct iwl_rx_phy_res *)
&priv->last_phy_res[1];
else
rx_start = NULL;
len = le16_to_cpu(rx_start->byte_count);
rx_end = (__le32 *)(pkt->u.raw + rx_start->cfg_phy_cnt +
- sizeof(struct iwl4965_rx_phy_res) + len);
+ sizeof(struct iwl_rx_phy_res) + len);
} else {
struct iwl4965_rx_mpdu_res_start *amsdu =
(struct iwl4965_rx_mpdu_res_start *)pkt->u.raw;
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
priv->last_phy_res[0] = 1;
memcpy(&priv->last_phy_res[1], &(pkt->u.raw[0]),
- sizeof(struct iwl4965_rx_phy_res));
+ sizeof(struct iwl_rx_phy_res));
}
EXPORT_SYMBOL(iwl_rx_reply_rx_phy);
clear_bit(STATUS_SCAN_HW, &priv->status);
}
+ priv->alloc_rxb_skb--;
dev_kfree_skb_any(cmd.meta.u.skb);
return ret;
static void iwl_rx_scan_complete_notif(struct iwl_priv *priv,
struct iwl_rx_mem_buffer *rxb)
{
+#ifdef CONFIG_IWLWIFI_DEBUG
struct iwl_rx_packet *pkt = (struct iwl_rx_packet *)rxb->skb->data;
struct iwl_scancomplete_notification *scan_notif = (void *)pkt->u.raw;
scan_notif->scanned_channels,
scan_notif->tsf_low,
scan_notif->tsf_high, scan_notif->status);
+#endif
/* The HW is no longer scanning */
clear_bit(STATUS_SCAN_HW, &priv->status);
if (lq->sta_id == 0xFF)
lq->sta_id = IWL_AP_ID;
- iwl_dump_lq_cmd(priv,lq);
+ iwl_dump_lq_cmd(priv, lq);
if (iwl_is_associated(priv) && priv->assoc_station_added)
return iwl_send_cmd(priv, &cmd);
* for automatic fallback during transmission.
*
* NOTE: This sets up a default set of values. These will be replaced later
- * if the driver's iwl-4965-rs rate scaling algorithm is used, instead of
+ * if the driver's iwl-agn-rs rate scaling algorithm is used, instead of
* rc80211_simple.
*
* NOTE: Run REPLY_ADD_STA command to set up station table entry, before
* Free all buffers.
* 0-fill, but do not free "txq" descriptor structure.
*/
-static void iwl_tx_queue_free(struct iwl_priv *priv, struct iwl_tx_queue *txq)
+static void iwl_tx_queue_free(struct iwl_priv *priv, int txq_id)
{
+ struct iwl_tx_queue *txq = &priv->txq[txq_id];
struct iwl_queue *q = &txq->q;
struct pci_dev *dev = priv->pci_dev;
- int len;
+ int i, slots_num, len;
if (q->n_bd == 0)
return;
len += IWL_MAX_SCAN_SIZE;
/* De-alloc array of command/tx buffers */
- pci_free_consistent(dev, len, txq->cmd, txq->dma_addr_cmd);
+ slots_num = (txq_id == IWL_CMD_QUEUE_NUM) ?
+ TFD_CMD_SLOTS : TFD_TX_CMD_SLOTS;
+ for (i = 0; i < slots_num; i++)
+ kfree(txq->cmd[i]);
+ if (txq_id == IWL_CMD_QUEUE_NUM)
+ kfree(txq->cmd[slots_num]);
/* De-alloc circular buffer of TFDs */
if (txq->q.n_bd)
struct iwl_tx_queue *txq,
int slots_num, u32 txq_id)
{
- struct pci_dev *dev = priv->pci_dev;
- int len;
+ int i, len;
int rc = 0;
/*
* For normal Tx queues (all other queues), no super-size command
* space is needed.
*/
- len = sizeof(struct iwl_cmd) * slots_num;
- if (txq_id == IWL_CMD_QUEUE_NUM)
- len += IWL_MAX_SCAN_SIZE;
- txq->cmd = pci_alloc_consistent(dev, len, &txq->dma_addr_cmd);
- if (!txq->cmd)
- return -ENOMEM;
+ len = sizeof(struct iwl_cmd);
+ for (i = 0; i <= slots_num; i++) {
+ if (i == slots_num) {
+ if (txq_id == IWL_CMD_QUEUE_NUM)
+ len += IWL_MAX_SCAN_SIZE;
+ else
+ continue;
+ }
+
+ txq->cmd[i] = kmalloc(len, GFP_KERNEL | GFP_DMA);
+ if (!txq->cmd[i])
+ return -ENOMEM;
+ }
/* Alloc driver data array and TFD circular buffer */
rc = iwl_tx_queue_alloc(priv, txq, txq_id);
if (rc) {
- pci_free_consistent(dev, len, txq->cmd, txq->dma_addr_cmd);
+ for (i = 0; i < slots_num; i++)
+ kfree(txq->cmd[i]);
return -ENOMEM;
}
/* Tx queues */
for (txq_id = 0; txq_id < priv->hw_params.max_txq_num; txq_id++)
- iwl_tx_queue_free(priv, &priv->txq[txq_id]);
+ iwl_tx_queue_free(priv, txq_id);
/* Keep-warm buffer */
iwl_kw_free(priv);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct iwl_tfd_frame *tfd;
- u32 *control_flags;
- int txq_id = skb_get_queue_mapping(skb);
- struct iwl_tx_queue *txq = NULL;
- struct iwl_queue *q = NULL;
+ struct iwl_tx_queue *txq;
+ struct iwl_queue *q;
+ struct iwl_cmd *out_cmd;
+ struct iwl_tx_cmd *tx_cmd;
+ int swq_id, txq_id;
dma_addr_t phys_addr;
dma_addr_t txcmd_phys;
dma_addr_t scratch_phys;
- struct iwl_cmd *out_cmd = NULL;
- struct iwl_tx_cmd *tx_cmd;
u16 len, idx, len_org;
u16 seq_number = 0;
- u8 id, hdr_len, unicast;
- u8 sta_id;
__le16 fc;
+ u8 hdr_len, unicast;
+ u8 sta_id;
u8 wait_write_ptr = 0;
u8 tid = 0;
u8 *qc = NULL;
}
unicast = !is_multicast_ether_addr(hdr->addr1);
- id = 0;
fc = hdr->frame_control;
IWL_DEBUG_TX("station Id %d\n", sta_id);
+ swq_id = skb_get_queue_mapping(skb);
+ txq_id = swq_id;
if (ieee80211_is_data_qos(fc)) {
qc = ieee80211_get_qos_ctl(hdr);
tid = qc[0] & 0xf;
- seq_number = priv->stations[sta_id].tid[tid].seq_number &
- IEEE80211_SCTL_SEQ;
- hdr->seq_ctrl = cpu_to_le16(seq_number) |
- (hdr->seq_ctrl &
- __constant_cpu_to_le16(IEEE80211_SCTL_FRAG));
+ seq_number = priv->stations[sta_id].tid[tid].seq_number;
+ seq_number &= IEEE80211_SCTL_SEQ;
+ hdr->seq_ctrl = hdr->seq_ctrl &
+ __constant_cpu_to_le16(IEEE80211_SCTL_FRAG);
+ hdr->seq_ctrl |= cpu_to_le16(seq_number);
seq_number += 0x10;
/* aggregation is on for this <sta,tid> */
if (info->flags & IEEE80211_TX_CTL_AMPDU)
/* Set up first empty TFD within this queue's circular TFD buffer */
tfd = &txq->bd[q->write_ptr];
memset(tfd, 0, sizeof(*tfd));
- control_flags = (u32 *) tfd;
idx = get_cmd_index(q, q->write_ptr, 0);
/* Set up driver data for this TFD */
txq->txb[q->write_ptr].skb[0] = skb;
/* Set up first empty entry in queue's array of Tx/cmd buffers */
- out_cmd = &txq->cmd[idx];
+ out_cmd = txq->cmd[idx];
tx_cmd = &out_cmd->cmd.tx;
memset(&out_cmd->hdr, 0, sizeof(out_cmd->hdr));
memset(tx_cmd, 0, sizeof(struct iwl_tx_cmd));
/* Physical address of this Tx command's header (not MAC header!),
* within command buffer array. */
- txcmd_phys = txq->dma_addr_cmd + sizeof(struct iwl_cmd) * idx +
- offsetof(struct iwl_cmd, hdr);
+ txcmd_phys = pci_map_single(priv->pci_dev, out_cmd,
+ sizeof(struct iwl_cmd), PCI_DMA_TODEVICE);
+ txcmd_phys += offsetof(struct iwl_cmd, hdr);
/* Add buffer containing Tx command and MAC(!) header to TFD's
* first entry */
iwl_hw_txq_attach_buf_to_tfd(priv, tfd, txcmd_phys, len);
- if (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT))
+ if (info->control.hw_key)
iwl_tx_cmd_build_hwcrypto(priv, info, tx_cmd, skb, sta_id);
/* Set up TFD's 2nd entry to point directly to remainder of skb,
if (ret)
return ret;
- if ((iwl_queue_space(q) < q->high_mark)
- && priv->mac80211_registered) {
+ if ((iwl_queue_space(q) < q->high_mark) && priv->mac80211_registered) {
if (wait_write_ptr) {
spin_lock_irqsave(&priv->lock, flags);
txq->need_update = 1;
iwl_txq_update_write_ptr(priv, txq);
spin_unlock_irqrestore(&priv->lock, flags);
+ } else {
+ ieee80211_stop_queue(priv->hw, swq_id);
}
-
- ieee80211_stop_queue(priv->hw, skb_get_queue_mapping(skb));
}
return 0;
struct iwl_tx_queue *txq = &priv->txq[IWL_CMD_QUEUE_NUM];
struct iwl_queue *q = &txq->q;
struct iwl_tfd_frame *tfd;
- u32 *control_flags;
struct iwl_cmd *out_cmd;
- u32 idx;
- u16 fix_size;
dma_addr_t phys_addr;
- int ret;
unsigned long flags;
+ int len, ret;
+ u32 idx;
+ u16 fix_size;
cmd->len = priv->cfg->ops->utils->get_hcmd_size(cmd->id, cmd->len);
fix_size = (u16)(cmd->len + sizeof(out_cmd->hdr));
tfd = &txq->bd[q->write_ptr];
memset(tfd, 0, sizeof(*tfd));
- control_flags = (u32 *) tfd;
idx = get_cmd_index(q, q->write_ptr, cmd->meta.flags & CMD_SIZE_HUGE);
- out_cmd = &txq->cmd[idx];
+ out_cmd = txq->cmd[idx];
out_cmd->hdr.cmd = cmd->id;
memcpy(&out_cmd->meta, &cmd->meta, sizeof(cmd->meta));
INDEX_TO_SEQ(q->write_ptr));
if (out_cmd->meta.flags & CMD_SIZE_HUGE)
out_cmd->hdr.sequence |= cpu_to_le16(SEQ_HUGE_FRAME);
-
- phys_addr = txq->dma_addr_cmd + sizeof(txq->cmd[0]) * idx +
- offsetof(struct iwl_cmd, hdr);
+ len = (idx == TFD_CMD_SLOTS) ?
+ IWL_MAX_SCAN_SIZE : sizeof(struct iwl_cmd);
+ phys_addr = pci_map_single(priv->pci_dev, out_cmd, len,
+ PCI_DMA_TODEVICE);
+ phys_addr += offsetof(struct iwl_cmd, hdr);
iwl_hw_txq_attach_buf_to_tfd(priv, tfd, phys_addr, fix_size);
IWL_DEBUG_HC("Sending command %s (#%x), seq: 0x%04X, "
{
struct iwl_tx_queue *txq = &priv->txq[txq_id];
struct iwl_queue *q = &txq->q;
+ struct iwl_tfd_frame *bd = &txq->bd[index];
+ dma_addr_t dma_addr;
+ int is_odd, buf_len;
int nfreed = 0;
if ((index >= q->n_bd) || (iwl_queue_used(q, index) == 0)) {
q->write_ptr, q->read_ptr);
queue_work(priv->workqueue, &priv->restart);
}
+ is_odd = (index/2) & 0x1;
+ if (is_odd) {
+ dma_addr = IWL_GET_BITS(bd->pa[index], tb2_addr_lo16) |
+ (IWL_GET_BITS(bd->pa[index],
+ tb2_addr_hi20) << 16);
+ buf_len = IWL_GET_BITS(bd->pa[index], tb2_len);
+ } else {
+ dma_addr = le32_to_cpu(bd->pa[index].tb1_addr);
+ buf_len = IWL_GET_BITS(bd->pa[index], tb1_len);
+ }
+
+ pci_unmap_single(priv->pci_dev, dma_addr, buf_len,
+ PCI_DMA_TODEVICE);
nfreed++;
}
}
BUG_ON(txq_id != IWL_CMD_QUEUE_NUM);
cmd_index = get_cmd_index(&priv->txq[IWL_CMD_QUEUE_NUM].q, index, huge);
- cmd = &priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_index];
+ cmd = priv->txq[IWL_CMD_QUEUE_NUM].cmd[cmd_index];
/* Input error checking is done when commands are added to queue. */
if (cmd->meta.flags & CMD_WANT_SKB) {
/* For each frame attempted in aggregation,
* update driver's record of tx frame's status. */
for (i = 0; i < agg->frame_count ; i++) {
- ack = bitmap & (1 << i);
+ ack = bitmap & (1ULL << i);
successes += !!ack;
IWL_DEBUG_TX_REPLY("%s ON i=%d idx=%d raw=%d\n",
ack? "ACK":"NACK", i, (agg->start_idx + i) & 0xff,
return 0;
error:
- if (txq->txb) {
- kfree(txq->txb);
- txq->txb = NULL;
- }
+ kfree(txq->txb);
+ txq->txb = NULL;
return -ENOMEM;
}
txq->q.n_bd, txq->bd, txq->q.dma_addr);
/* De-alloc array of per-TFD driver data */
- if (txq->txb) {
- kfree(txq->txb);
- txq->txb = NULL;
- }
+ kfree(txq->txb);
+ txq->txb = NULL;
/* 0-fill queue descriptor structure */
memset(txq, 0, sizeof(*txq));
* first entry */
iwl3945_hw_txq_attach_buf_to_tfd(priv, tfd, txcmd_phys, len);
- if (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT))
+ if (info->control.hw_key)
iwl3945_build_tx_cmd_hwcrypto(priv, info, out_cmd, skb, 0);
/* Set up TFD's 2nd entry to point directly to remainder of skb,
if (!ieee80211_has_morefrags(hdr->frame_control)) {
txq->need_update = 1;
- if (qc) {
+ if (qc)
priv->stations[sta_id].tid[tid].seq_number = seq_number;
- }
} else {
wait_write_ptr = 1;
txq->need_update = 0;
/* 100:1 or higher, divide by 10 and use table,
* add 20 dB to make up for divide by 10 */
if (sig_ratio >= 100)
- return (20 + (int)ratio2dB[sig_ratio/10]);
+ return 20 + (int)ratio2dB[sig_ratio/10];
/* We shouldn't see this */
if (sig_ratio < 1)
* iwl3945_verify_inst_full - verify runtime uCode image in card vs. host,
* looking at all data.
*/
-static int iwl3945_verify_inst_full(struct iwl3945_priv *priv, __le32 * image, u32 len)
+static int iwl3945_verify_inst_full(struct iwl3945_priv *priv, __le32 *image, u32 len)
{
u32 val;
u32 save_len = len;
val = iwl3945_read_prph(priv, BSM_WR_DWCOUNT_REG);
for (reg = BSM_SRAM_LOWER_BOUND;
reg < BSM_SRAM_LOWER_BOUND + len;
- reg += sizeof(u32), image ++) {
+ reg += sizeof(u32), image++) {
val = iwl3945_read_prph(priv, reg);
if (val != le32_to_cpu(*image)) {
IWL_ERROR("BSM uCode verification failed at "
DECLARE_MAC_BUF(mac);
if (priv->iw_mode == IEEE80211_IF_TYPE_AP) {
- IWL_ERROR("%s Should not be called in AP mode\n", __FUNCTION__);
+ IWL_ERROR("%s Should not be called in AP mode\n", __func__);
return;
}
default:
IWL_ERROR("%s Should not be called in %d mode\n",
- __FUNCTION__, priv->iw_mode);
+ __func__, priv->iw_mode);
break;
}
IWL_DEBUG_MAC80211("enter\n");
- if (priv->iw_mode == IEEE80211_IF_TYPE_MNTR) {
- IWL_DEBUG_MAC80211("leave - monitor\n");
- dev_kfree_skb_any(skb);
- return 0;
- }
-
IWL_DEBUG_TX("dev->xmit(%d bytes) at rate 0x%02x\n", skb->len,
ieee80211_get_tx_rate(hw, IEEE80211_SKB_CB(skb))->bitrate);
struct iwl3945_priv *priv = dev_get_drvdata(d);
struct iwl3945_spectrum_notification measure_report;
u32 size = sizeof(measure_report), len = 0, ofs = 0;
- u8 *data = (u8 *) & measure_report;
+ u8 *data = (u8 *)&measure_report;
unsigned long flags;
spin_lock_irqsave(&priv->lock, flags);
else
p += sprintf(p, " \n");
- return (p - buf + 1);
+ return p - buf + 1;
}
struct iwl3945_priv *priv = dev_get_drvdata(d);
u32 size = sizeof(struct iwl3945_notif_statistics);
u32 len = 0, ofs = 0;
- u8 *data = (u8 *) & priv->statistics;
+ u8 *data = (u8 *)&priv->statistics;
int rc = 0;
if (!iwl3945_is_alive(priv))
priv->ibss_beacon = NULL;
/* Tell mac80211 our characteristics */
- hw->flags = IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
- IEEE80211_HW_SIGNAL_DBM |
+ hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM;
/* 4 EDCA QOS priorities */
/* nic init */
iwl3945_set_bit(priv, CSR_GIO_CHICKEN_BITS,
- CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
-
- iwl3945_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
- err = iwl3945_poll_bit(priv, CSR_GP_CNTRL,
- CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
- CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
- if (err < 0) {
- IWL_DEBUG_INFO("Failed to init the card\n");
+ CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
+
+ iwl3945_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+ err = iwl3945_poll_bit(priv, CSR_GP_CNTRL,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
+ if (err < 0) {
+ IWL_DEBUG_INFO("Failed to init the card\n");
goto out_remove_sysfs;
- }
+ }
/* Read the EEPROM */
err = iwl3945_eeprom_init(priv);
if (err) {
iwl3945_unset_hw_setting(priv);
iwl3945_clear_stations_table(priv);
- if (priv->mac80211_registered) {
+ if (priv->mac80211_registered)
ieee80211_unregister_hw(priv->hw);
- }
/*netif_stop_queue(dev); */
flush_workqueue(priv->workqueue);
lbs_add_rtap(priv);
}
priv->monitormode = monitor_mode;
- }
-
- else {
+ } else {
if (!priv->monitormode)
return strlen(buf);
priv->monitormode = 0;
lbs_pr_err("cannot register ethX device\n");
goto done;
}
- if (device_create_file(&dev->dev, &dev_attr_lbs_rtap))
- lbs_pr_err("cannot register lbs_rtap attribute\n");
lbs_update_channel(priv);
if (device_create_file(&dev->dev, &dev_attr_lbs_mesh))
lbs_pr_err("cannot register lbs_mesh attribute\n");
+
+ /* While rtap isn't related to mesh, only mesh-enabled
+ * firmware implements the rtap functionality via
+ * CMD_802_11_MONITOR_MODE.
+ */
+ if (device_create_file(&dev->dev, &dev_attr_lbs_rtap))
+ lbs_pr_err("cannot register lbs_rtap attribute\n");
}
}
netif_carrier_off(priv->dev);
lbs_debugfs_remove_one(priv);
- device_remove_file(&dev->dev, &dev_attr_lbs_rtap);
if (priv->mesh_tlv) {
device_remove_file(&dev->dev, &dev_attr_lbs_mesh);
+ device_remove_file(&dev->dev, &dev_attr_lbs_rtap);
}
/* Flush pending command nodes */
if (ret)
return ret;
- return snprintf(buf, 12, "0x%x\n", le32_to_cpu(defs.bootflag));
+ return snprintf(buf, 12, "%d\n", le32_to_cpu(defs.bootflag));
}
/**
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%x", &datum);
- if (ret != 1)
+ ret = sscanf(buf, "%d", &datum);
+ if ((ret != 1) || (datum > 1))
return -EINVAL;
*((__le32 *)&cmd.data[0]) = cpu_to_le32(!!datum);
if (ret)
return ret;
- return snprintf(buf, 12, "0x%x\n", defs.boottime);
+ return snprintf(buf, 12, "%d\n", defs.boottime);
}
/**
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%x", &datum);
- if (ret != 1)
+ ret = sscanf(buf, "%d", &datum);
+ if ((ret != 1) || (datum > 255))
return -EINVAL;
/* A too small boot time will result in the device booting into
if (ret)
return ret;
- return snprintf(buf, 12, "0x%x\n", le16_to_cpu(defs.channel));
+ return snprintf(buf, 12, "%d\n", le16_to_cpu(defs.channel));
}
/**
{
struct lbs_private *priv = to_net_dev(dev)->priv;
struct cmd_ds_mesh_config cmd;
- uint16_t datum;
+ uint32_t datum;
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%hx", &datum);
+ ret = sscanf(buf, "%d", &datum);
if (ret != 1 || datum < 1 || datum > 11)
return -EINVAL;
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%x", &datum);
- if (ret != 1)
+ ret = sscanf(buf, "%d", &datum);
+ if ((ret != 1) || (datum > 255))
return -EINVAL;
/* fetch all other Information Element parameters */
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%x", &datum);
- if (ret != 1)
+ ret = sscanf(buf, "%d", &datum);
+ if ((ret != 1) || (datum > 255))
return -EINVAL;
/* fetch all other Information Element parameters */
int ret;
memset(&cmd, 0, sizeof(cmd));
- ret = sscanf(buf, "%x", &datum);
- if (ret != 1)
+ ret = sscanf(buf, "%d", &datum);
+ if ((ret != 1) || (datum > 255))
return -EINVAL;
/* fetch all other Information Element parameters */
device_unregister(data->dev);
failed_drvdata:
ieee80211_free_hw(hw);
- hwsim_radios[i] = 0;
+ hwsim_radios[i] = NULL;
failed:
mac80211_hwsim_free();
return err;
else
priv->mc_count = mc_count;
}
-
- /* Since we can set the promiscuous flag when it wasn't asked
- for, make sure the net_device knows about it. */
- if (priv->promiscuous)
- dev->flags |= IFF_PROMISC;
- else
- dev->flags &= ~IFF_PROMISC;
}
/* This must be called from user context, without locks held - use
int (*open)(struct ieee80211_hw *dev);
void (*stop)(struct ieee80211_hw *dev);
int mode;
+ u16 seqno;
+ struct mutex conf_mutex;
u8 mac_addr[ETH_ALEN];
u8 bssid[ETH_ALEN];
struct pda_iq_autocal_entry *iq_autocal;
struct ieee80211_tx_queue_stats *current_queue;
struct p54_common *priv = dev->priv;
struct p54_control_hdr *hdr;
+ struct ieee80211_hdr *ieee80211hdr = (struct ieee80211_hdr *)skb->data;
struct p54_tx_control_allocdata *txhdr;
size_t padding, len;
u8 rate;
if (padding)
txhdr->align[0] = padding;
+ /* FIXME: The sequence that follows is needed for this driver to
+ * work with mac80211 since "mac80211: fix TX sequence numbers".
+ * As with the temporary code in rt2x00, changes will be needed
+ * to get proper sequence numbers on beacons. In addition, this
+ * patch places the sequence number in the hardware state, which
+ * limits us to a single virtual state.
+ */
+ if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
+ if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
+ priv->seqno += 0x10;
+ ieee80211hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
+ ieee80211hdr->seq_ctrl |= cpu_to_le16(priv->seqno);
+ }
/* modifies skb->cb and with it info, so must be last! */
p54_assign_address(dev, skb, hdr, skb->len);
if (dev->conf.flags & IEEE80211_CONF_SHORT_SLOT_TIME) {
vdcf->slottime = 9;
- vdcf->magic1 = 0x00;
- vdcf->magic2 = 0x10;
+ vdcf->magic1 = 0x10;
+ vdcf->magic2 = 0x00;
} else {
vdcf->slottime = 20;
vdcf->magic1 = 0x0a;
static int p54_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf)
{
int ret;
+ struct p54_common *priv = dev->priv;
+ mutex_lock(&priv->conf_mutex);
ret = p54_set_freq(dev, cpu_to_le16(conf->channel->center_freq));
p54_set_vdcf(dev);
+ mutex_unlock(&priv->conf_mutex);
return ret;
}
{
struct p54_common *priv = dev->priv;
+ mutex_lock(&priv->conf_mutex);
p54_set_filter(dev, 0, priv->mac_addr, conf->bssid, 0, 1, 0, 0xF642);
p54_set_filter(dev, 0, priv->mac_addr, conf->bssid, 2, 0, 0, 0);
p54_set_leds(dev, 1, !is_multicast_ether_addr(conf->bssid), 0);
memcpy(priv->bssid, conf->bssid, ETH_ALEN);
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
}
p54_init_vdcf(dev);
+ mutex_init(&priv->conf_mutex);
return dev;
}
#define PRISM2_HOSTAPD_MAX_BUF_SIZE 1024
#define PRISM2_HOSTAPD_GENERIC_ELEMENT_HDR_LEN \
-((int) (&((struct prism2_hostapd_param *) 0)->u.generic_elem.data))
+ offsetof(struct prism2_hostapd_param, u.generic_elem.data)
/* Maximum length for algorithm names (-1 for nul termination)
* used in ioctl() */
rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->ifs);
rt2x00_set_field32(&word, TXD_W0_RETRY_MODE,
test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags));
+ rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skb->len);
rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, CIPHER_NONE);
rt2x00_desc_write(txd, 0, word);
}
rt2x00dev->link.vgc_level = value;
}
+/*
+ * NOTE: This function is directly ported from legacy driver, but
+ * despite it being declared it was never called. Although link tuning
+ * sounds like a good idea, and usually works well for the other drivers,
+ * it does _not_ work with rt2500usb. Enabling this function will result
+ * in TX capabilities only until association kicks in. Immediately
+ * after the successful association all TX frames will be kept in the
+ * hardware queue and never transmitted.
+ */
+#if 0
static void rt2500usb_link_tuner(struct rt2x00_dev *rt2x00dev)
{
int rssi = rt2x00_get_link_rssi(&rt2x00dev->link);
rt2x00dev->link.vgc_level = r17;
}
}
+#else
+#define rt2500usb_link_tuner NULL
+#endif
/*
* Initialization functions.
int pipe = usb_sndbulkpipe(usb_dev, 1);
int length;
u16 reg;
+ u32 word, len;
/*
* Add the descriptor in front of the skb.
memcpy(entry->skb->data, skbdesc->desc, skbdesc->desc_len);
skbdesc->desc = entry->skb->data;
+ /*
+ * Adjust the beacon databyte count. The current number is
+ * calculated before this function gets called, but falsely
+ * assumes that the descriptor was already present in the SKB.
+ */
+ rt2x00_desc_read(skbdesc->desc, 0, &word);
+ len = rt2x00_get_field32(word, TXD_W0_DATABYTE_COUNT);
+ len += skbdesc->desc_len;
+ rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, len);
+ rt2x00_desc_write(skbdesc->desc, 0, word);
+
/*
* Disable beaconing while we are reloading the beacon data,
* otherwise we might be sending out invalid data.
rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp);
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word);
EEPROM(rt2x00dev, "BBPtune vgc: 0x%04x\n", word);
+ } else {
+ rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp);
+ rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word);
}
rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R17, &word);
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_HIGH, 0x41);
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R17, word);
EEPROM(rt2x00dev, "BBPtune r17: 0x%04x\n", word);
- } else {
- rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp);
- rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word);
}
rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24, &word);
* Initialize all hw fields.
*/
rt2x00dev->hw->flags =
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
IEEE80211_HW_RX_INCLUDES_FCS |
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
IEEE80211_HW_SIGNAL_DBM;
__set_bit(DRIVER_REQUIRE_ATIM_QUEUE, &rt2x00dev->flags);
__set_bit(DRIVER_REQUIRE_BEACON_GUARD, &rt2x00dev->flags);
__set_bit(DRIVER_REQUIRE_SCHEDULED, &rt2x00dev->flags);
+ __set_bit(CONFIG_DISABLE_LINK_TUNING, &rt2x00dev->flags);
/*
* Set the rssi offset.
#define SHORT_PIFS ( SIFS + SHORT_SLOT_TIME )
#define DIFS ( PIFS + SLOT_TIME )
#define SHORT_DIFS ( SHORT_PIFS + SHORT_SLOT_TIME )
-#define EIFS ( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
+#define EIFS ( SIFS + DIFS + \
+ (8 * (IEEE80211_HEADER + ACK_SIZE)) )
+#define SHORT_EIFS ( SIFS + SHORT_DIFS + \
+ (8 * (IEEE80211_HEADER + ACK_SIZE)) )
/*
* Chipset identification
#define DELAYED_CONFIG_ERP 0x00000002
#define DELAYED_LED_ASSOC 0x00000004
+ /*
+ * Software sequence counter, this is only required
+ * for hardware which doesn't support hardware
+ * sequence counting.
+ */
+ spinlock_t seqlock;
u16 seqno;
};
DEVICE_STARTED_SUSPEND,
DEVICE_ENABLED_RADIO,
DEVICE_DISABLED_RADIO_HW,
+ DEVICE_DIRTY_CONFIG,
/*
* Driver features
libconf.ant.rx = default_ant->rx;
else if (active_ant->rx == ANTENNA_SW_DIVERSITY)
libconf.ant.rx = ANTENNA_B;
+ else
+ libconf.ant.rx = active_ant->rx;
if (conf->antenna_sel_tx)
libconf.ant.tx = conf->antenna_sel_tx;
libconf.ant.tx = default_ant->tx;
else if (active_ant->tx == ANTENNA_SW_DIVERSITY)
libconf.ant.tx = ANTENNA_B;
+ else
+ libconf.ant.tx = active_ant->tx;
}
if (flags & CONFIG_UPDATE_SLOT_TIME) {
libconf.sifs = SIFS;
libconf.pifs = short_slot_time ? SHORT_PIFS : PIFS;
libconf.difs = short_slot_time ? SHORT_DIFS : DIFS;
- libconf.eifs = EIFS;
+ libconf.eifs = short_slot_time ? SHORT_EIFS : EIFS;
}
libconf.conf = conf;
if (*offset) \
return 0; \
\
- if (!capable(CAP_NET_ADMIN)) \
- return -EPERM; \
- \
if (intf->offset_##__name >= debug->__name.word_count) \
return -EINVAL; \
\
data += sprintf(data, "compiled: %s %s\n", __DATE__, __TIME__);
blob->size = strlen(blob->data);
- return debugfs_create_blob(name, S_IRUGO, intf->driver_folder, blob);
+ return debugfs_create_blob(name, S_IRUSR, intf->driver_folder, blob);
}
static struct dentry *rt2x00debug_create_file_chipset(const char *name,
data += sprintf(data, "rf length: %d\n", debug->rf.word_count);
blob->size = strlen(blob->data);
- return debugfs_create_blob(name, S_IRUGO, intf->driver_folder, blob);
+ return debugfs_create_blob(name, S_IRUSR, intf->driver_folder, blob);
}
void rt2x00debug_register(struct rt2x00_dev *rt2x00dev)
if (IS_ERR(intf->chipset_entry))
goto exit;
- intf->dev_flags = debugfs_create_file("dev_flags", S_IRUGO,
+ intf->dev_flags = debugfs_create_file("dev_flags", S_IRUSR,
intf->driver_folder, intf,
&rt2x00debug_fop_dev_flags);
if (IS_ERR(intf->dev_flags))
({ \
(__intf)->__name##_off_entry = \
debugfs_create_u32(__stringify(__name) "_offset", \
- S_IRUGO | S_IWUSR, \
+ S_IRUSR | S_IWUSR, \
(__intf)->register_folder, \
&(__intf)->offset_##__name); \
if (IS_ERR((__intf)->__name##_off_entry)) \
\
(__intf)->__name##_val_entry = \
debugfs_create_file(__stringify(__name) "_value", \
- S_IRUGO | S_IWUSR, \
+ S_IRUSR | S_IWUSR, \
(__intf)->register_folder, \
(__intf), &rt2x00debug_fop_##__name);\
if (IS_ERR((__intf)->__name##_val_entry)) \
goto exit;
intf->queue_frame_dump_entry =
- debugfs_create_file("dump", S_IRUGO, intf->queue_folder,
+ debugfs_create_file("dump", S_IRUSR, intf->queue_folder,
intf, &rt2x00debug_fop_queue_dump);
if (IS_ERR(intf->queue_frame_dump_entry))
goto exit;
init_waitqueue_head(&intf->frame_dump_waitqueue);
intf->queue_stats_entry =
- debugfs_create_file("queue", S_IRUGO, intf->queue_folder,
+ debugfs_create_file("queue", S_IRUSR, intf->queue_folder,
intf, &rt2x00debug_fop_queue_stats);
return;
rt2x00dev->intf_associated = 0;
__set_bit(DEVICE_STARTED, &rt2x00dev->flags);
+ __set_bit(DEVICE_DIRTY_CONFIG, &rt2x00dev->flags);
return 0;
}
/*
* Reconfigure device.
*/
- rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf, 1);
- if (!rt2x00dev->hw->conf.radio_enabled)
- rt2x00lib_disable_radio(rt2x00dev);
+ retval = rt2x00mac_config(rt2x00dev->hw, &rt2x00dev->hw->conf);
+ if (retval)
+ goto exit;
/*
* Iterator over each active interface to
*/
void rt2x00queue_free_skb(struct rt2x00_dev *rt2x00dev, struct sk_buff *skb);
-/**
- * rt2x00queue_free_skb - free a skb
- * @rt2x00dev: Pointer to &struct rt2x00_dev.
- * @skb: The skb to free.
- */
-void rt2x00queue_free_skb(struct rt2x00_dev *rt2x00dev, struct sk_buff *skb);
-
/**
* rt2x00queue_write_tx_frame - Write TX frame to hardware
* @queue: Queue over which the frame should be send
*/
memcpy(skb->cb, frag_skb->cb, sizeof(skb->cb));
rts_info = IEEE80211_SKB_CB(skb);
- rts_info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ rts_info->control.hw_key = NULL;
rts_info->flags &= ~IEEE80211_TX_CTL_USE_RTS_CTS;
rts_info->flags &= ~IEEE80211_TX_CTL_USE_CTS_PROTECT;
rts_info->flags &= ~IEEE80211_TX_CTL_REQ_TX_STATUS;
(struct ieee80211_rts *)(skb->data));
if (rt2x00queue_write_tx_frame(queue, skb)) {
+ dev_kfree_skb_any(skb);
WARNING(rt2x00dev, "Failed to send RTS/CTS frame.\n");
return NETDEV_TX_BUSY;
}
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
struct ieee80211_hdr *ieee80211hdr = (struct ieee80211_hdr *)skb->data;
enum data_queue_qid qid = skb_get_queue_mapping(skb);
- struct rt2x00_intf *intf = vif_to_intf(tx_info->control.vif);
struct data_queue *queue;
u16 frame_control;
}
}
- /*
- * XXX: This is as wrong as the old mac80211 code was,
- * due to beacons not getting sequence numbers assigned
- * properly.
- */
- if (tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
- if (tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
- intf->seqno += 0x10;
- ieee80211hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
- ieee80211hdr->seq_ctrl |= cpu_to_le16(intf->seqno);
- }
-
if (rt2x00queue_write_tx_frame(queue, skb)) {
ieee80211_stop_queue(rt2x00dev->hw, qid);
return NETDEV_TX_BUSY;
!test_bit(DEVICE_STARTED, &rt2x00dev->flags))
return -ENODEV;
- /*
- * We don't support mixed combinations of sta and ap virtual
- * interfaces. We can only add this interface when the rival
- * interface count is 0.
- */
- if ((conf->type == IEEE80211_IF_TYPE_AP && rt2x00dev->intf_sta_count) ||
- (conf->type != IEEE80211_IF_TYPE_AP && rt2x00dev->intf_ap_count))
- return -ENOBUFS;
-
- /*
- * Check if we exceeded the maximum amount of supported interfaces.
- */
- if ((conf->type == IEEE80211_IF_TYPE_AP &&
- rt2x00dev->intf_ap_count >= rt2x00dev->ops->max_ap_intf) ||
- (conf->type != IEEE80211_IF_TYPE_AP &&
- rt2x00dev->intf_sta_count >= rt2x00dev->ops->max_sta_intf))
- return -ENOBUFS;
+ switch (conf->type) {
+ case IEEE80211_IF_TYPE_AP:
+ /*
+ * We don't support mixed combinations of
+ * sta and ap interfaces.
+ */
+ if (rt2x00dev->intf_sta_count)
+ return -ENOBUFS;
+
+ /*
+ * Check if we exceeded the maximum amount
+ * of supported interfaces.
+ */
+ if (rt2x00dev->intf_ap_count >= rt2x00dev->ops->max_ap_intf)
+ return -ENOBUFS;
+
+ break;
+ case IEEE80211_IF_TYPE_STA:
+ case IEEE80211_IF_TYPE_IBSS:
+ /*
+ * We don't support mixed combinations of
+ * sta and ap interfaces.
+ */
+ if (rt2x00dev->intf_ap_count)
+ return -ENOBUFS;
+
+ /*
+ * Check if we exceeded the maximum amount
+ * of supported interfaces.
+ */
+ if (rt2x00dev->intf_sta_count >= rt2x00dev->ops->max_sta_intf)
+ return -ENOBUFS;
+
+ break;
+ default:
+ return -EINVAL;
+ }
/*
* Loop through all beacon queues to find a free
rt2x00dev->intf_sta_count++;
spin_lock_init(&intf->lock);
+ spin_lock_init(&intf->seqlock);
intf->beacon = entry;
if (conf->type == IEEE80211_IF_TYPE_AP)
int rt2x00mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
+ int force_reconfig;
/*
* Mac80211 might be calling this function while we are trying
rt2x00lib_toggle_rx(rt2x00dev, STATE_RADIO_RX_OFF);
}
- rt2x00lib_config(rt2x00dev, conf, 0);
+ /*
+ * When the DEVICE_DIRTY_CONFIG flag is set, the device has recently
+ * been started and the configuration must be forced upon the hardware.
+ * Otherwise registers will not be intialized correctly and could
+ * result in non-working hardware because essential registers aren't
+ * initialized.
+ */
+ force_reconfig =
+ __test_and_clear_bit(DEVICE_DIRTY_CONFIG, &rt2x00dev->flags);
+
+ rt2x00lib_config(rt2x00dev, conf, force_reconfig);
/*
* Reenable RX only if the radio should be on.
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
+ struct rt2x00_intf *intf = vif_to_intf(tx_info->control.vif);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)entry->skb->data;
struct ieee80211_rate *rate =
ieee80211_get_tx_rate(rt2x00dev->hw, tx_info);
unsigned int data_length;
unsigned int duration;
unsigned int residual;
+ unsigned long irqflags;
memset(txdesc, 0, sizeof(*txdesc));
txdesc->ifs = IFS_SIFS;
}
+ /*
+ * Hardware should insert sequence counter.
+ * FIXME: We insert a software sequence counter first for
+ * hardware that doesn't support hardware sequence counting.
+ *
+ * This is wrong because beacons are not getting sequence
+ * numbers assigned properly.
+ *
+ * A secondary problem exists for drivers that cannot toggle
+ * sequence counting per-frame, since those will override the
+ * sequence counter given by mac80211.
+ */
+ if (tx_info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
+ spin_lock_irqsave(&intf->seqlock, irqflags);
+
+ if (test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags))
+ intf->seqno += 0x10;
+ hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
+ hdr->seq_ctrl |= cpu_to_le16(intf->seqno);
+
+ spin_unlock_irqrestore(&intf->seqlock, irqflags);
+
+ __set_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags);
+ }
+
/*
* PLCP setup
* Length calculation depends on OFDM/CCK rate.
if (!rt2x00dev->ops->lib->init_rxentry)
return;
- for (i = 0; i < queue->limit; i++)
+ for (i = 0; i < queue->limit; i++) {
+ queue->entries[i].flags = 0;
+
rt2x00dev->ops->lib->init_rxentry(rt2x00dev,
&queue->entries[i]);
+ }
}
void rt2x00queue_init_tx(struct rt2x00_dev *rt2x00dev)
if (!rt2x00dev->ops->lib->init_txentry)
continue;
- for (i = 0; i < queue->limit; i++)
+ for (i = 0; i < queue->limit; i++) {
+ queue->entries[i].flags = 0;
+
rt2x00dev->ops->lib->init_txentry(rt2x00dev,
&queue->entries[i]);
+ }
}
}
* @ENTRY_TXD_RTS_FRAME: This frame is a RTS frame.
* @ENTRY_TXD_CTS_FRAME: This frame is a CTS-to-self frame.
* @ENTRY_TXD_OFDM_RATE: This frame is send out with an OFDM rate.
+ * @ENTRY_TXD_GENERATE_SEQ: This frame requires sequence counter.
* @ENTRY_TXD_FIRST_FRAGMENT: This is the first frame.
* @ENTRY_TXD_MORE_FRAG: This frame is followed by another fragment.
* @ENTRY_TXD_REQ_TIMESTAMP: Require timestamp to be inserted.
ENTRY_TXD_RTS_FRAME,
ENTRY_TXD_CTS_FRAME,
ENTRY_TXD_OFDM_RATE,
+ ENTRY_TXD_GENERATE_SEQ,
ENTRY_TXD_FIRST_FRAGMENT,
ENTRY_TXD_MORE_FRAG,
ENTRY_TXD_REQ_TIMESTAMP,
}
EXPORT_SYMBOL_GPL(rt2x00usb_vendor_request_buff);
+int rt2x00usb_vendor_request_large_buff(struct rt2x00_dev *rt2x00dev,
+ const u8 request, const u8 requesttype,
+ const u16 offset, const void *buffer,
+ const u16 buffer_length,
+ const int timeout)
+{
+ int status = 0;
+ unsigned char *tb;
+ u16 off, len, bsize;
+
+ mutex_lock(&rt2x00dev->usb_cache_mutex);
+
+ tb = (char *)buffer;
+ off = offset;
+ len = buffer_length;
+ while (len && !status) {
+ bsize = min_t(u16, CSR_CACHE_SIZE, len);
+ status = rt2x00usb_vendor_req_buff_lock(rt2x00dev, request,
+ requesttype, off, tb,
+ bsize, timeout);
+
+ tb += bsize;
+ len -= bsize;
+ off += bsize;
+ }
+
+ mutex_unlock(&rt2x00dev->usb_cache_mutex);
+
+ return status;
+}
+EXPORT_SYMBOL_GPL(rt2x00usb_vendor_request_large_buff);
+
/*
* TX data handlers.
*/
/*
* Cache size
*/
-#define CSR_CACHE_SIZE 8
-#define CSR_CACHE_SIZE_FIRMWARE 64
+#define CSR_CACHE_SIZE 64
/*
* USB request types.
const u16 offset, void *buffer,
const u16 buffer_length, const int timeout);
+/**
+ * rt2x00usb_vendor_request_large_buff - Send register command to device (buffered)
+ * @rt2x00dev: Pointer to &struct rt2x00_dev
+ * @request: USB vendor command (See &enum rt2x00usb_vendor_request)
+ * @requesttype: Request type &USB_VENDOR_REQUEST_*
+ * @offset: Register start offset to perform action on
+ * @buffer: Buffer where information will be read/written to by device
+ * @buffer_length: Size of &buffer
+ * @timeout: Operation timeout
+ *
+ * This function is used to transfer register data in blocks larger
+ * then CSR_CACHE_SIZE. Use for firmware upload, keys and beacons.
+ */
+int rt2x00usb_vendor_request_large_buff(struct rt2x00_dev *rt2x00dev,
+ const u8 request, const u8 requesttype,
+ const u16 offset, const void *buffer,
+ const u16 buffer_length,
+ const int timeout);
+
/**
* rt2x00usb_vendor_request_sw - Send single register command to device
* @rt2x00dev: Pointer to &struct rt2x00_dev
return -EBUSY;
}
+ /*
+ * Hardware needs another millisecond before it is ready.
+ */
+ msleep(1);
+
/*
* Reset MAC and BBP registers.
*/
rt2x00_set_field32(&word, TXD_W1_CWMIN, txdesc->cw_min);
rt2x00_set_field32(&word, TXD_W1_CWMAX, txdesc->cw_max);
rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, IEEE80211_HEADER);
- rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE, 1);
+ rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE,
+ test_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags));
rt2x00_set_field32(&word, TXD_W1_BUFFER_COUNT, 1);
rt2x00_desc_write(txd, 1, word);
* Initialize all hw fields.
*/
rt2x00dev->hw->flags =
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
IEEE80211_HW_SIGNAL_DBM;
rt2x00dev->hw->extra_tx_headroom = 0;
unsigned int i;
int status;
u32 reg;
- const char *ptr = data;
- char *cache;
- int buflen;
/*
* Wait for stable hardware.
/*
* Write firmware to device.
- * We setup a seperate cache for this action,
- * since we are going to write larger chunks of data
- * then normally used cache size.
*/
- cache = kmalloc(CSR_CACHE_SIZE_FIRMWARE, GFP_KERNEL);
- if (!cache) {
- ERROR(rt2x00dev, "Failed to allocate firmware cache.\n");
- return -ENOMEM;
- }
-
- for (i = 0; i < len; i += CSR_CACHE_SIZE_FIRMWARE) {
- buflen = min_t(int, len - i, CSR_CACHE_SIZE_FIRMWARE);
-
- memcpy(cache, ptr, buflen);
-
- rt2x00usb_vendor_request(rt2x00dev, USB_MULTI_WRITE,
- USB_VENDOR_REQUEST_OUT,
- FIRMWARE_IMAGE_BASE + i, 0,
- cache, buflen,
- REGISTER_TIMEOUT32(buflen));
-
- ptr += buflen;
- }
-
- kfree(cache);
+ rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE,
+ USB_VENDOR_REQUEST_OUT,
+ FIRMWARE_IMAGE_BASE,
+ data, len,
+ REGISTER_TIMEOUT32(len));
/*
* Send firmware request to device to load firmware,
rt2x00_set_field32(&word, TXD_W1_CWMIN, txdesc->cw_min);
rt2x00_set_field32(&word, TXD_W1_CWMAX, txdesc->cw_max);
rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, IEEE80211_HEADER);
- rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE, 1);
+ rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE,
+ test_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags));
rt2x00_desc_write(txd, 1, word);
rt2x00_desc_read(txd, 2, &word);
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
unsigned int beacon_base;
u32 reg;
+ u32 word, len;
/*
* Add the descriptor in front of the skb.
memcpy(entry->skb->data, skbdesc->desc, skbdesc->desc_len);
skbdesc->desc = entry->skb->data;
+ /*
+ * Adjust the beacon databyte count. The current number is
+ * calculated before this function gets called, but falsely
+ * assumes that the descriptor was already present in the SKB.
+ */
+ rt2x00_desc_read(skbdesc->desc, 0, &word);
+ len = rt2x00_get_field32(word, TXD_W0_DATABYTE_COUNT);
+ len += skbdesc->desc_len;
+ rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, len);
+ rt2x00_desc_write(skbdesc->desc, 0, word);
+
/*
* Disable beaconing while we are reloading the beacon data,
* otherwise we might be sending out invalid data.
* Write entire beacon with descriptor to register.
*/
beacon_base = HW_BEACON_OFFSET(entry->entry_idx);
- rt2x00usb_vendor_request(rt2x00dev, USB_MULTI_WRITE,
- USB_VENDOR_REQUEST_OUT, beacon_base, 0,
- entry->skb->data, entry->skb->len,
- REGISTER_TIMEOUT32(entry->skb->len));
+ rt2x00usb_vendor_request_large_buff(rt2x00dev, USB_MULTI_WRITE,
+ USB_VENDOR_REQUEST_OUT, beacon_base,
+ entry->skb->data, entry->skb->len,
+ REGISTER_TIMEOUT32(entry->skb->len));
/*
* Clean up the beacon skb.
* Initialize all hw fields.
*/
rt2x00dev->hw->flags =
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
IEEE80211_HW_SIGNAL_DBM;
rt2x00dev->hw->extra_tx_headroom = TXD_DESC_SIZE;
struct rtl8187b_rx_hdr {
__le32 flags;
__le64 mac_time;
- u8 noise;
- u8 signal;
+ u8 sq;
+ u8 rssi;
u8 agc;
- u8 reserved;
- __le32 unused;
+ u8 flags2;
+ __le16 snr_long2end;
+ s8 pwdb_g12;
+ u8 fot;
} __attribute__((packed));
/* {rtl8187,rtl8187b}_tx_info is in skb */
const struct rtl818x_rf_ops *rf;
struct ieee80211_vif *vif;
int mode;
+ /* The mutex protects the TX loopback state.
+ * Any attempt to set channels concurrently locks the device.
+ */
+ struct mutex conf_mutex;
/* rtl8187 specific */
struct ieee80211_channel channels[14];
struct usb_device *udev;
u32 rx_conf;
u16 txpwr_base;
+ u16 seqno;
u8 asic_rev;
u8 is_rtl8187b;
enum {
MODULE_LICENSE("GPL");
static struct usb_device_id rtl8187_table[] __devinitdata = {
+ /* Asus */
+ {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187},
/* Realtek */
{USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187},
{USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B},
{
struct rtl8187_priv *priv = dev->priv;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_hdr *ieee80211hdr = (struct ieee80211_hdr *)skb->data;
unsigned int ep;
void *buf;
struct urb *urb;
ep = epmap[skb_get_queue_mapping(skb)];
}
+ /* FIXME: The sequence that follows is needed for this driver to
+ * work with mac80211 since "mac80211: fix TX sequence numbers".
+ * As with the temporary code in rt2x00, changes will be needed
+ * to get proper sequence numbers on beacons. In addition, this
+ * patch places the sequence number in the hardware state, which
+ * limits us to a single virtual state.
+ */
+ if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) {
+ if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT)
+ priv->seqno += 0x10;
+ ieee80211hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG);
+ ieee80211hdr->seq_ctrl |= cpu_to_le16(priv->seqno);
+ }
+
info->driver_data[0] = dev;
info->driver_data[1] = urb;
struct ieee80211_rx_status rx_status = { 0 };
int rate, signal;
u32 flags;
+ u32 quality;
spin_lock(&priv->rx_queue.lock);
if (skb->next)
flags = le32_to_cpu(hdr->flags);
signal = hdr->signal & 0x7f;
rx_status.antenna = (hdr->signal >> 7) & 1;
- rx_status.signal = signal;
rx_status.noise = hdr->noise;
rx_status.mactime = le64_to_cpu(hdr->mac_time);
- priv->signal = signal;
priv->quality = signal;
+ rx_status.qual = priv->quality;
priv->noise = hdr->noise;
+ rate = (flags >> 20) & 0xF;
+ if (rate > 3) { /* OFDM rate */
+ if (signal > 90)
+ signal = 90;
+ else if (signal < 25)
+ signal = 25;
+ signal = 90 - signal;
+ } else { /* CCK rate */
+ if (signal > 95)
+ signal = 95;
+ else if (signal < 30)
+ signal = 30;
+ signal = 95 - signal;
+ }
+ rx_status.signal = signal;
+ priv->signal = signal;
} else {
struct rtl8187b_rx_hdr *hdr =
(typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
+ /* The Realtek datasheet for the RTL8187B shows that the RX
+ * header contains the following quantities: signal quality,
+ * RSSI, AGC, the received power in dB, and the measured SNR.
+ * In testing, none of these quantities show qualitative
+ * agreement with AP signal strength, except for the AGC,
+ * which is inversely proportional to the strength of the
+ * signal. In the following, the quality and signal strength
+ * are derived from the AGC. The arbitrary scaling constants
+ * are chosen to make the results close to the values obtained
+ * for a BCM4312 using b43 as the driver. The noise is ignored
+ * for now.
+ */
flags = le32_to_cpu(hdr->flags);
- signal = hdr->agc >> 1;
- rx_status.antenna = (hdr->signal >> 7) & 1;
- rx_status.signal = 64 - min(hdr->noise, (u8)64);
- rx_status.noise = hdr->noise;
+ quality = 170 - hdr->agc;
+ if (quality > 100)
+ quality = 100;
+ signal = 14 - hdr->agc / 2;
+ rx_status.qual = quality;
+ priv->quality = quality;
+ rx_status.signal = signal;
+ priv->signal = signal;
+ rx_status.antenna = (hdr->rssi >> 7) & 1;
rx_status.mactime = le64_to_cpu(hdr->mac_time);
- priv->signal = hdr->signal;
- priv->quality = hdr->agc >> 1;
- priv->noise = hdr->noise;
+ rate = (flags >> 20) & 0xF;
}
skb_trim(skb, flags & 0x0FFF);
- rate = (flags >> 20) & 0xF;
- if (rate > 3) { /* OFDM rate */
- if (signal > 90)
- signal = 90;
- else if (signal < 25)
- signal = 25;
- signal = 90 - signal;
- } else { /* CCK rate */
- if (signal > 95)
- signal = 95;
- else if (signal < 30)
- signal = 30;
- signal = 95 - signal;
- }
-
- rx_status.qual = priv->quality;
- rx_status.signal = signal;
rx_status.rate_idx = rate;
rx_status.freq = dev->conf.channel->center_freq;
rx_status.band = dev->conf.channel->band;
if (ret)
return ret;
+ mutex_lock(&priv->conf_mutex);
if (priv->is_rtl8187b) {
reg = RTL818X_RX_CONF_MGMT |
RTL818X_RX_CONF_DATA |
(7 << 0 /* long retry limit */) |
(7 << 21 /* MAX TX DMA */));
rtl8187_init_urbs(dev);
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
reg |= RTL818X_CMD_TX_ENABLE;
reg |= RTL818X_CMD_RX_ENABLE;
rtl818x_iowrite8(priv, &priv->map->CMD, reg);
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
struct sk_buff *skb;
u32 reg;
+ mutex_lock(&priv->conf_mutex);
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
reg = rtl818x_ioread8(priv, &priv->map->CMD);
usb_kill_urb(info->urb);
kfree_skb(skb);
}
- return;
+ mutex_unlock(&priv->conf_mutex);
}
static int rtl8187_add_interface(struct ieee80211_hw *dev,
return -EOPNOTSUPP;
}
+ mutex_lock(&priv->conf_mutex);
priv->vif = conf->vif;
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
((u8 *)conf->mac_addr)[i]);
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
struct ieee80211_if_init_conf *conf)
{
struct rtl8187_priv *priv = dev->priv;
+ mutex_lock(&priv->conf_mutex);
priv->mode = IEEE80211_IF_TYPE_MNTR;
priv->vif = NULL;
+ mutex_unlock(&priv->conf_mutex);
}
static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf)
struct rtl8187_priv *priv = dev->priv;
u32 reg;
+ mutex_lock(&priv->conf_mutex);
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
/* Enable TX loopback on MAC level to avoid TX during channel
* changes, as this has be seen to causes problems and the
rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
int i;
u8 reg;
+ mutex_lock(&priv->conf_mutex);
for (i = 0; i < ETH_ALEN; i++)
rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]);
rtl818x_iowrite8(priv, &priv->map->MSR, reg);
}
+ mutex_unlock(&priv->conf_mutex);
return 0;
}
priv->mode = IEEE80211_IF_TYPE_MNTR;
dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
- IEEE80211_HW_RX_INCLUDES_FCS |
- IEEE80211_HW_SIGNAL_UNSPEC;
- dev->max_signal = 65;
+ IEEE80211_HW_RX_INCLUDES_FCS;
eeprom.data = dev;
eeprom.register_read = rtl8187_eeprom_register_read;
(*channel++).hw_value = txpwr >> 8;
}
- if (priv->is_rtl8187b)
+ if (priv->is_rtl8187b) {
printk(KERN_WARNING "rtl8187: 8187B chip detected. Support "
"is EXPERIMENTAL, and could damage your\n"
" hardware, use at your own risk\n");
+ dev->flags |= IEEE80211_HW_SIGNAL_DBM;
+ } else {
+ dev->flags |= IEEE80211_HW_SIGNAL_UNSPEC;
+ dev->max_signal = 65;
+ }
+
if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
" info!\n");
printk(KERN_ERR "rtl8187: Cannot register device\n");
goto err_free_dev;
}
+ mutex_init(&priv->conf_mutex);
printk(KERN_INFO "%s: hwaddr %s, %s V%d + %s\n",
wiphy_name(dev->wiphy), print_mac(mac, dev->wiphy->perm_addr),
lp->mc_count = 0;
wv_82586_reconfig(dev);
-
- /* Tell the kernel that we are doing a really bad job. */
- dev->flags |= IFF_PROMISC;
}
} else
/* Are there multicast addresses to send? */
lp->mc_count = 0;
wv_82593_reconfig(dev);
-
- /* Tell the kernel that we are doing a really bad job... */
- dev->flags |= IFF_PROMISC;
}
}
else
lp->mc_count = 0;
wv_82593_reconfig(dev);
-
- /* Tell the kernel that we are doing a really bad job... */
- dev->flags |= IFF_ALLMULTI;
}
}
else
hw->wiphy->bands[IEEE80211_BAND_2GHZ] = &mac->band;
hw->flags = IEEE80211_HW_RX_INCLUDES_FCS |
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE |
IEEE80211_HW_SIGNAL_DB;
hw->max_signal = 100;
}
spin_unlock_bh(&np->rx_lock);
- xennet_maybe_wake_tx(dev);
+ netif_start_queue(dev);
return 0;
}
#include <pcmcia/ss.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/sizes.h>
#include <asm/gpio.h>
-#include <asm/arch/board.h>
-#include <asm/arch/at91rm9200_mc.h>
+#include <mach/board.h>
+#include <mach/at91rm9200_mc.h>
/*
#include <pcmcia/ss.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/tc.h>
+#include <mach/mux.h>
+#include <mach/tc.h>
/* NOTE: don't expect this to support many I/O cards. The 16xx chips have
#include <linux/spinlock.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/ss.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#include "soc_common.h"
#include <linux/init.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/sa1111.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/lubbock.h>
+#include <mach/pxa-regs.h>
+#include <mach/lubbock.h>
#include "sa1111_generic.h"
#include <pcmcia/ss.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mainstone.h>
+#include <mach/pxa-regs.h>
+#include <mach/mainstone.h>
#include "soc_common.h"
#include <asm/mach-types.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/palmtx.h>
+#include <mach/gpio.h>
+#include <mach/palmtx.h>
#include "soc_common.h"
#include <linux/platform_device.h>
#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/hardware/scoop.h>
destroy_cis_cache(s);
}
s->cis_mem.res = NULL;
- if ((ret != 0) || (count == 0))
+ if ((ret != 0) || (*count == 0))
return 0;
return 1;
}
#include <linux/device.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/signal.h>
-#include <asm/arch/assabet.h>
+#include <mach/assabet.h>
#include "sa1100_generic.h"
#include <linux/errno.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/badge4.h>
+#include <mach/badge4.h>
#include <asm/hardware/sa1111.h>
#include "sa1111_generic.h"
#include <linux/init.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
-#include <asm/arch/cerf.h>
+#include <mach/cerf.h>
#include "sa1100_generic.h"
#define CERF_SOCKET 1
#include <linux/init.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
-#include <asm/arch/h3600.h>
+#include <mach/h3600.h>
#include "sa1100_generic.h"
#include <linux/errno.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/sa1111.h>
#include <asm/mach-types.h>
#include <linux/errno.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/neponset.h>
+#include <mach/neponset.h>
#include <asm/hardware/sa1111.h>
#include "sa1111_generic.h"
#include <linux/device.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/shannon.h>
+#include <mach/shannon.h>
#include <asm/irq.h>
#include "sa1100_generic.h"
#include <linux/device.h>
#include <linux/init.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
-#include <asm/arch/simpad.h>
+#include <mach/simpad.h>
#include "sa1100_generic.h"
extern long get_cs3_shadow(void);
#include <pcmcia/ss.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/sa1111.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/kernel.h>
#include <linux/spinlock.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <linux/spinlock.h>
#include <linux/cpufreq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/system.h>
/* FIXME: platform dependent resource declaration has to move out of this file */
#ifdef CONFIG_ARCH_PXA
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#endif
#ifdef DEBUG
{
#ifdef DEBUG
char buf[128];
- int len = 0;
+ int len;
struct pnp_resource *pnp_res;
struct resource *res;
dev_dbg(&dev->dev, "%s: current resources:\n", desc);
list_for_each_entry(pnp_res, &dev->resources, list) {
res = &pnp_res->res;
+ len = 0;
- len += snprintf(buf + len, sizeof(buf) - len, " %-3s ",
- pnp_resource_type_name(res));
+ len += scnprintf(buf + len, sizeof(buf) - len, " %-3s ",
+ pnp_resource_type_name(res));
if (res->flags & IORESOURCE_DISABLED) {
dev_dbg(&dev->dev, "%sdisabled\n", buf);
switch (pnp_resource_type(res)) {
case IORESOURCE_IO:
case IORESOURCE_MEM:
- len += snprintf(buf + len, sizeof(buf) - len,
- "%#llx-%#llx flags %#lx",
- (unsigned long long) res->start,
- (unsigned long long) res->end,
- res->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ "%#llx-%#llx flags %#lx",
+ (unsigned long long) res->start,
+ (unsigned long long) res->end,
+ res->flags);
break;
case IORESOURCE_IRQ:
case IORESOURCE_DMA:
- len += snprintf(buf + len, sizeof(buf) - len,
- "%lld flags %#lx",
- (unsigned long long) res->start,
- res->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ "%lld flags %#lx",
+ (unsigned long long) res->start,
+ res->flags);
break;
}
dev_dbg(&dev->dev, "%s\n", buf);
struct pnp_dma *dma;
if (pnp_option_is_dependent(option))
- len += snprintf(buf + len, sizeof(buf) - len,
- " dependent set %d (%s) ",
- pnp_option_set(option),
- pnp_option_priority_name(option));
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ " dependent set %d (%s) ",
+ pnp_option_set(option),
+ pnp_option_priority_name(option));
else
- len += snprintf(buf + len, sizeof(buf) - len, " independent ");
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ " independent ");
switch (option->type) {
case IORESOURCE_IO:
port = &option->u.port;
- len += snprintf(buf + len, sizeof(buf) - len, "io min %#llx "
- "max %#llx align %lld size %lld flags %#x",
- (unsigned long long) port->min,
- (unsigned long long) port->max,
- (unsigned long long) port->align,
- (unsigned long long) port->size, port->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len, "io min %#llx "
+ "max %#llx align %lld size %lld flags %#x",
+ (unsigned long long) port->min,
+ (unsigned long long) port->max,
+ (unsigned long long) port->align,
+ (unsigned long long) port->size, port->flags);
break;
case IORESOURCE_MEM:
mem = &option->u.mem;
- len += snprintf(buf + len, sizeof(buf) - len, "mem min %#llx "
- "max %#llx align %lld size %lld flags %#x",
- (unsigned long long) mem->min,
- (unsigned long long) mem->max,
- (unsigned long long) mem->align,
- (unsigned long long) mem->size, mem->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len, "mem min %#llx "
+ "max %#llx align %lld size %lld flags %#x",
+ (unsigned long long) mem->min,
+ (unsigned long long) mem->max,
+ (unsigned long long) mem->align,
+ (unsigned long long) mem->size, mem->flags);
break;
case IORESOURCE_IRQ:
irq = &option->u.irq;
- len += snprintf(buf + len, sizeof(buf) - len, "irq");
+ len += scnprintf(buf + len, sizeof(buf) - len, "irq");
if (bitmap_empty(irq->map.bits, PNP_IRQ_NR))
- len += snprintf(buf + len, sizeof(buf) - len,
- " <none>");
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ " <none>");
else {
for (i = 0; i < PNP_IRQ_NR; i++)
if (test_bit(i, irq->map.bits))
- len += snprintf(buf + len,
- sizeof(buf) - len,
- " %d", i);
+ len += scnprintf(buf + len,
+ sizeof(buf) - len,
+ " %d", i);
}
- len += snprintf(buf + len, sizeof(buf) - len, " flags %#x",
- irq->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len, " flags %#x",
+ irq->flags);
if (irq->flags & IORESOURCE_IRQ_OPTIONAL)
- len += snprintf(buf + len, sizeof(buf) - len,
- " (optional)");
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ " (optional)");
break;
case IORESOURCE_DMA:
dma = &option->u.dma;
- len += snprintf(buf + len, sizeof(buf) - len, "dma");
+ len += scnprintf(buf + len, sizeof(buf) - len, "dma");
if (!dma->map)
- len += snprintf(buf + len, sizeof(buf) - len,
- " <none>");
+ len += scnprintf(buf + len, sizeof(buf) - len,
+ " <none>");
else {
for (i = 0; i < 8; i++)
if (dma->map & (1 << i))
- len += snprintf(buf + len,
- sizeof(buf) - len,
- " %d", i);
+ len += scnprintf(buf + len,
+ sizeof(buf) - len,
+ " %d", i);
}
- len += snprintf(buf + len, sizeof(buf) - len, " (bitmask %#x) "
- "flags %#x", dma->map, dma->flags);
+ len += scnprintf(buf + len, sizeof(buf) - len, " (bitmask %#x) "
+ "flags %#x", dma->map, dma->flags);
break;
}
dev_dbg(&dev->dev, "%s\n", buf);
help
Say Y to enable support for the battery on the OLPC laptop.
+config BATTERY_TOSA
+ tristate "Sharp SL-6000 (tosa) battery"
+ depends on MACH_TOSA && MFD_TC6393XB
+ help
+ Say Y to enable support for the battery on the Sharp Zaurus
+ SL-6000 (tosa) models.
+
config BATTERY_PALMTX
tristate "Palm T|X battery"
depends on MACH_PALMTX
obj-$(CONFIG_BATTERY_DS2760) += ds2760_battery.o
obj-$(CONFIG_BATTERY_PMU) += pmu_battery.o
obj-$(CONFIG_BATTERY_OLPC) += olpc_battery.o
+obj-$(CONFIG_BATTERY_TOSA) += tosa_battery.o
obj-$(CONFIG_BATTERY_PALMTX) += palmtx_battery.o
#define EC_BAT_VOLTAGE 0x10 /* uint16_t, *9.76/32, mV */
#define EC_BAT_CURRENT 0x11 /* int16_t, *15.625/120, mA */
-#define EC_BAT_ACR 0x12
+#define EC_BAT_ACR 0x12 /* int16_t, *6250/15, µAh */
#define EC_BAT_TEMP 0x13 /* uint16_t, *100/256, °C */
#define EC_AMB_TEMP 0x14 /* uint16_t, *100/256, °C */
#define EC_BAT_STATUS 0x15 /* uint8_t, bitmask */
.get_property = olpc_ac_get_prop,
};
+static char bat_serial[17]; /* Ick */
+
+static int olpc_bat_get_status(union power_supply_propval *val, uint8_t ec_byte)
+{
+ if (olpc_platform_info.ecver > 0x44) {
+ if (ec_byte & BAT_STAT_CHARGING)
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ else if (ec_byte & BAT_STAT_DISCHARGING)
+ val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+ else if (ec_byte & BAT_STAT_FULL)
+ val->intval = POWER_SUPPLY_STATUS_FULL;
+ else /* er,... */
+ val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ } else {
+ /* Older EC didn't report charge/discharge bits */
+ if (!(ec_byte & BAT_STAT_AC)) /* No AC means discharging */
+ val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+ else if (ec_byte & BAT_STAT_FULL)
+ val->intval = POWER_SUPPLY_STATUS_FULL;
+ else /* Not _necessarily_ true but EC doesn't tell all yet */
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ }
+
+ return 0;
+}
+
+static int olpc_bat_get_health(union power_supply_propval *val)
+{
+ uint8_t ec_byte;
+ int ret;
+
+ ret = olpc_ec_cmd(EC_BAT_ERRCODE, NULL, 0, &ec_byte, 1);
+ if (ret)
+ return ret;
+
+ switch (ec_byte) {
+ case 0:
+ val->intval = POWER_SUPPLY_HEALTH_GOOD;
+ break;
+
+ case BAT_ERR_OVERTEMP:
+ val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
+ break;
+
+ case BAT_ERR_OVERVOLTAGE:
+ val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ break;
+
+ case BAT_ERR_INFOFAIL:
+ case BAT_ERR_OUT_OF_CONTROL:
+ case BAT_ERR_ID_FAIL:
+ case BAT_ERR_ACR_FAIL:
+ val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
+ break;
+
+ default:
+ /* Eep. We don't know this failure code */
+ ret = -EIO;
+ }
+
+ return ret;
+}
+
+static int olpc_bat_get_mfr(union power_supply_propval *val)
+{
+ uint8_t ec_byte;
+ int ret;
+
+ ec_byte = BAT_ADDR_MFR_TYPE;
+ ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &ec_byte, 1);
+ if (ret)
+ return ret;
+
+ switch (ec_byte >> 4) {
+ case 1:
+ val->strval = "Gold Peak";
+ break;
+ case 2:
+ val->strval = "BYD";
+ break;
+ default:
+ val->strval = "Unknown";
+ break;
+ }
+
+ return ret;
+}
+
+static int olpc_bat_get_tech(union power_supply_propval *val)
+{
+ uint8_t ec_byte;
+ int ret;
+
+ ec_byte = BAT_ADDR_MFR_TYPE;
+ ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &ec_byte, 1);
+ if (ret)
+ return ret;
+
+ switch (ec_byte & 0xf) {
+ case 1:
+ val->intval = POWER_SUPPLY_TECHNOLOGY_NiMH;
+ break;
+ case 2:
+ val->intval = POWER_SUPPLY_TECHNOLOGY_LiFe;
+ break;
+ default:
+ val->intval = POWER_SUPPLY_TECHNOLOGY_UNKNOWN;
+ break;
+ }
+
+ return ret;
+}
+
/*********************************************************************
* Battery properties
*********************************************************************/
int ret = 0;
int16_t ec_word;
uint8_t ec_byte;
+ uint64_t ser_buf;
ret = olpc_ec_cmd(EC_BAT_STATUS, NULL, 0, &ec_byte, 1);
if (ret)
switch (psp) {
case POWER_SUPPLY_PROP_STATUS:
- if (olpc_platform_info.ecver > 0x44) {
- if (ec_byte & BAT_STAT_CHARGING)
- val->intval = POWER_SUPPLY_STATUS_CHARGING;
- else if (ec_byte & BAT_STAT_DISCHARGING)
- val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
- else if (ec_byte & BAT_STAT_FULL)
- val->intval = POWER_SUPPLY_STATUS_FULL;
- else /* er,... */
- val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
- } else {
- /* Older EC didn't report charge/discharge bits */
- if (!(ec_byte & BAT_STAT_AC)) /* No AC means discharging */
- val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
- else if (ec_byte & BAT_STAT_FULL)
- val->intval = POWER_SUPPLY_STATUS_FULL;
- else /* Not _necessarily_ true but EC doesn't tell all yet */
- val->intval = POWER_SUPPLY_STATUS_CHARGING;
- break;
- }
+ ret = olpc_bat_get_status(val, ec_byte);
+ if (ret)
+ return ret;
+ break;
case POWER_SUPPLY_PROP_PRESENT:
val->intval = !!(ec_byte & BAT_STAT_PRESENT);
break;
if (ec_byte & BAT_STAT_DESTROY)
val->intval = POWER_SUPPLY_HEALTH_DEAD;
else {
- ret = olpc_ec_cmd(EC_BAT_ERRCODE, NULL, 0, &ec_byte, 1);
+ ret = olpc_bat_get_health(val);
if (ret)
return ret;
-
- switch (ec_byte) {
- case 0:
- val->intval = POWER_SUPPLY_HEALTH_GOOD;
- break;
-
- case BAT_ERR_OVERTEMP:
- val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
- break;
-
- case BAT_ERR_OVERVOLTAGE:
- val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
- break;
-
- case BAT_ERR_INFOFAIL:
- case BAT_ERR_OUT_OF_CONTROL:
- case BAT_ERR_ID_FAIL:
- case BAT_ERR_ACR_FAIL:
- val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
- break;
-
- default:
- /* Eep. We don't know this failure code */
- return -EIO;
- }
}
break;
case POWER_SUPPLY_PROP_MANUFACTURER:
- ec_byte = BAT_ADDR_MFR_TYPE;
- ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &ec_byte, 1);
+ ret = olpc_bat_get_mfr(val);
if (ret)
return ret;
-
- switch (ec_byte >> 4) {
- case 1:
- val->strval = "Gold Peak";
- break;
- case 2:
- val->strval = "BYD";
- break;
- default:
- val->strval = "Unknown";
- break;
- }
break;
case POWER_SUPPLY_PROP_TECHNOLOGY:
- ec_byte = BAT_ADDR_MFR_TYPE;
- ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &ec_byte, 1);
+ ret = olpc_bat_get_tech(val);
if (ret)
return ret;
-
- switch (ec_byte & 0xf) {
- case 1:
- val->intval = POWER_SUPPLY_TECHNOLOGY_NiMH;
- break;
- case 2:
- val->intval = POWER_SUPPLY_TECHNOLOGY_LiFe;
- break;
- default:
- val->intval = POWER_SUPPLY_TECHNOLOGY_UNKNOWN;
- break;
- }
break;
case POWER_SUPPLY_PROP_VOLTAGE_AVG:
ret = olpc_ec_cmd(EC_BAT_VOLTAGE, NULL, 0, (void *)&ec_word, 2);
ec_word = be16_to_cpu(ec_word);
val->intval = ec_word * 100 / 256;
break;
+ case POWER_SUPPLY_PROP_CHARGE_COUNTER:
+ ret = olpc_ec_cmd(EC_BAT_ACR, NULL, 0, (void *)&ec_word, 2);
+ if (ret)
+ return ret;
+
+ ec_word = be16_to_cpu(ec_word);
+ val->intval = ec_word * 6250 / 15;
+ break;
+ case POWER_SUPPLY_PROP_SERIAL_NUMBER:
+ ret = olpc_ec_cmd(EC_BAT_SERIAL, NULL, 0, (void *)&ser_buf, 8);
+ if (ret)
+ return ret;
+
+ sprintf(bat_serial, "%016llx", (long long)be64_to_cpu(ser_buf));
+ val->strval = bat_serial;
+ break;
default:
ret = -EINVAL;
break;
POWER_SUPPLY_PROP_TEMP,
POWER_SUPPLY_PROP_TEMP_AMBIENT,
POWER_SUPPLY_PROP_MANUFACTURER,
+ POWER_SUPPLY_PROP_SERIAL_NUMBER,
+ POWER_SUPPLY_PROP_CHARGE_COUNTER,
+};
+
+/* EEPROM reading goes completely around the power_supply API, sadly */
+
+#define EEPROM_START 0x20
+#define EEPROM_END 0x80
+#define EEPROM_SIZE (EEPROM_END - EEPROM_START)
+
+static ssize_t olpc_bat_eeprom_read(struct kobject *kobj,
+ struct bin_attribute *attr, char *buf, loff_t off, size_t count)
+{
+ uint8_t ec_byte;
+ int ret, end;
+
+ if (off >= EEPROM_SIZE)
+ return 0;
+ if (off + count > EEPROM_SIZE)
+ count = EEPROM_SIZE - off;
+
+ end = EEPROM_START + off + count;
+ for (ec_byte = EEPROM_START + off; ec_byte < end; ec_byte++) {
+ ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1,
+ &buf[ec_byte - EEPROM_START], 1);
+ if (ret) {
+ printk(KERN_ERR "olpc-battery: EC command "
+ "EC_BAT_EEPROM @ 0x%x failed -"
+ " %d!\n", ec_byte, ret);
+ return -EIO;
+ }
+ }
+
+ return count;
+}
+
+static struct bin_attribute olpc_bat_eeprom = {
+ .attr = {
+ .name = "eeprom",
+ .mode = S_IRUGO,
+ .owner = THIS_MODULE,
+ },
+ .size = 0,
+ .read = olpc_bat_eeprom_read,
};
/*********************************************************************
if (!olpc_platform_info.ecver)
return -ENXIO;
- if (olpc_platform_info.ecver < 0x43) {
- printk(KERN_NOTICE "OLPC EC version 0x%02x too old for battery driver.\n", olpc_platform_info.ecver);
+
+ /*
+ * We've seen a number of EC protocol changes; this driver requires
+ * the latest EC protocol, supported by 0x44 and above.
+ */
+ if (olpc_platform_info.ecver < 0x44) {
+ printk(KERN_NOTICE "OLPC EC version 0x%02x too old for "
+ "battery driver.\n", olpc_platform_info.ecver);
return -ENXIO;
}
if (ret)
goto battery_failed;
+ ret = device_create_bin_file(olpc_bat.dev, &olpc_bat_eeprom);
+ if (ret)
+ goto eeprom_failed;
+
goto success;
+eeprom_failed:
+ power_supply_unregister(&olpc_bat);
battery_failed:
power_supply_unregister(&olpc_ac);
ac_failed:
static void __exit olpc_bat_exit(void)
{
+ device_remove_bin_file(olpc_bat.dev, &olpc_bat_eeprom);
power_supply_unregister(&olpc_bat);
power_supply_unregister(&olpc_ac);
platform_device_unregister(bat_pdev);
#include <linux/gpio.h>
#include <asm/mach-types.h>
-#include <asm/arch/palmtx.h>
+#include <mach/palmtx.h>
static DEFINE_MUTEX(bat_lock);
static struct work_struct bat_work;
POWER_SUPPLY_ATTR(charge_empty),
POWER_SUPPLY_ATTR(charge_now),
POWER_SUPPLY_ATTR(charge_avg),
+ POWER_SUPPLY_ATTR(charge_counter),
POWER_SUPPLY_ATTR(energy_full_design),
POWER_SUPPLY_ATTR(energy_empty_design),
POWER_SUPPLY_ATTR(energy_full),
--- /dev/null
+/*
+ * Battery and Power Management code for the Sharp SL-6000x
+ *
+ * Copyright (c) 2005 Dirk Opfer
+ * Copyright (c) 2008 Dmitry Baryshkov
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/power_supply.h>
+#include <linux/wm97xx.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <mach/tosa.h>
+
+static DEFINE_MUTEX(bat_lock); /* protects gpio pins */
+static struct work_struct bat_work;
+
+struct tosa_bat {
+ int status;
+ struct power_supply psy;
+ int full_chrg;
+
+ struct mutex work_lock; /* protects data */
+
+ bool (*is_present)(struct tosa_bat *bat);
+ int gpio_full;
+ int gpio_charge_off;
+
+ int technology;
+
+ int gpio_bat;
+ int adc_bat;
+ int adc_bat_divider;
+ int bat_max;
+ int bat_min;
+
+ int gpio_temp;
+ int adc_temp;
+ int adc_temp_divider;
+};
+
+static struct tosa_bat tosa_bat_main;
+static struct tosa_bat tosa_bat_jacket;
+
+static unsigned long tosa_read_bat(struct tosa_bat *bat)
+{
+ unsigned long value = 0;
+
+ if (bat->gpio_bat < 0 || bat->adc_bat < 0)
+ return 0;
+
+ mutex_lock(&bat_lock);
+ gpio_set_value(bat->gpio_bat, 1);
+ msleep(5);
+ value = wm97xx_read_aux_adc(bat->psy.dev->parent->driver_data,
+ bat->adc_bat);
+ gpio_set_value(bat->gpio_bat, 0);
+ mutex_unlock(&bat_lock);
+
+ value = value * 1000000 / bat->adc_bat_divider;
+
+ return value;
+}
+
+static unsigned long tosa_read_temp(struct tosa_bat *bat)
+{
+ unsigned long value = 0;
+
+ if (bat->gpio_temp < 0 || bat->adc_temp < 0)
+ return 0;
+
+ mutex_lock(&bat_lock);
+ gpio_set_value(bat->gpio_temp, 1);
+ msleep(5);
+ value = wm97xx_read_aux_adc(bat->psy.dev->parent->driver_data,
+ bat->adc_temp);
+ gpio_set_value(bat->gpio_temp, 0);
+ mutex_unlock(&bat_lock);
+
+ value = value * 10000 / bat->adc_temp_divider;
+
+ return value;
+}
+
+static int tosa_bat_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ int ret = 0;
+ struct tosa_bat *bat = container_of(psy, struct tosa_bat, psy);
+
+ if (bat->is_present && !bat->is_present(bat)
+ && psp != POWER_SUPPLY_PROP_PRESENT) {
+ return -ENODEV;
+ }
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ val->intval = bat->status;
+ break;
+ case POWER_SUPPLY_PROP_TECHNOLOGY:
+ val->intval = bat->technology;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ val->intval = tosa_read_bat(bat);
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_MAX:
+ if (bat->full_chrg == -1)
+ val->intval = bat->bat_max;
+ else
+ val->intval = bat->full_chrg;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+ val->intval = bat->bat_max;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+ val->intval = bat->bat_min;
+ break;
+ case POWER_SUPPLY_PROP_TEMP:
+ val->intval = tosa_read_temp(bat);
+ break;
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = bat->is_present ? bat->is_present(bat) : 1;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ return ret;
+}
+
+static bool tosa_jacket_bat_is_present(struct tosa_bat *bat)
+{
+ return gpio_get_value(TOSA_GPIO_JACKET_DETECT) == 0;
+}
+
+static void tosa_bat_external_power_changed(struct power_supply *psy)
+{
+ schedule_work(&bat_work);
+}
+
+static irqreturn_t tosa_bat_gpio_isr(int irq, void *data)
+{
+ pr_info("tosa_bat_gpio irq: %d\n", gpio_get_value(irq_to_gpio(irq)));
+ schedule_work(&bat_work);
+ return IRQ_HANDLED;
+}
+
+static void tosa_bat_update(struct tosa_bat *bat)
+{
+ int old;
+ struct power_supply *psy = &bat->psy;
+
+ mutex_lock(&bat->work_lock);
+
+ old = bat->status;
+
+ if (bat->is_present && !bat->is_present(bat)) {
+ printk(KERN_NOTICE "%s not present\n", psy->name);
+ bat->status = POWER_SUPPLY_STATUS_UNKNOWN;
+ bat->full_chrg = -1;
+ } else if (power_supply_am_i_supplied(psy)) {
+ if (bat->status == POWER_SUPPLY_STATUS_DISCHARGING) {
+ gpio_set_value(bat->gpio_charge_off, 0);
+ mdelay(15);
+ }
+
+ if (gpio_get_value(bat->gpio_full)) {
+ if (old == POWER_SUPPLY_STATUS_CHARGING ||
+ bat->full_chrg == -1)
+ bat->full_chrg = tosa_read_bat(bat);
+
+ gpio_set_value(bat->gpio_charge_off, 1);
+ bat->status = POWER_SUPPLY_STATUS_FULL;
+ } else {
+ gpio_set_value(bat->gpio_charge_off, 0);
+ bat->status = POWER_SUPPLY_STATUS_CHARGING;
+ }
+ } else {
+ gpio_set_value(bat->gpio_charge_off, 1);
+ bat->status = POWER_SUPPLY_STATUS_DISCHARGING;
+ }
+
+ if (old != bat->status)
+ power_supply_changed(psy);
+
+ mutex_unlock(&bat->work_lock);
+}
+
+static void tosa_bat_work(struct work_struct *work)
+{
+ tosa_bat_update(&tosa_bat_main);
+ tosa_bat_update(&tosa_bat_jacket);
+}
+
+
+static enum power_supply_property tosa_bat_main_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_TECHNOLOGY,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_MAX,
+ POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+ POWER_SUPPLY_PROP_TEMP,
+ POWER_SUPPLY_PROP_PRESENT,
+};
+
+static enum power_supply_property tosa_bat_bu_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_TECHNOLOGY,
+ POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
+ POWER_SUPPLY_PROP_PRESENT,
+};
+
+static struct tosa_bat tosa_bat_main = {
+ .status = POWER_SUPPLY_STATUS_DISCHARGING,
+ .full_chrg = -1,
+ .psy = {
+ .name = "main-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = tosa_bat_main_props,
+ .num_properties = ARRAY_SIZE(tosa_bat_main_props),
+ .get_property = tosa_bat_get_property,
+ .external_power_changed = tosa_bat_external_power_changed,
+ .use_for_apm = 1,
+ },
+
+ .gpio_full = TOSA_GPIO_BAT0_CRG,
+ .gpio_charge_off = TOSA_GPIO_CHARGE_OFF,
+
+ .technology = POWER_SUPPLY_TECHNOLOGY_LIPO,
+
+ .gpio_bat = TOSA_GPIO_BAT0_V_ON,
+ .adc_bat = WM97XX_AUX_ID3,
+ .adc_bat_divider = 414,
+ .bat_max = 4310000,
+ .bat_min = 1551 * 1000000 / 414,
+
+ .gpio_temp = TOSA_GPIO_BAT1_TH_ON,
+ .adc_temp = WM97XX_AUX_ID2,
+ .adc_temp_divider = 10000,
+};
+
+static struct tosa_bat tosa_bat_jacket = {
+ .status = POWER_SUPPLY_STATUS_DISCHARGING,
+ .full_chrg = -1,
+ .psy = {
+ .name = "jacket-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = tosa_bat_main_props,
+ .num_properties = ARRAY_SIZE(tosa_bat_main_props),
+ .get_property = tosa_bat_get_property,
+ .external_power_changed = tosa_bat_external_power_changed,
+ },
+
+ .is_present = tosa_jacket_bat_is_present,
+ .gpio_full = TOSA_GPIO_BAT1_CRG,
+ .gpio_charge_off = TOSA_GPIO_CHARGE_OFF_JC,
+
+ .technology = POWER_SUPPLY_TECHNOLOGY_LIPO,
+
+ .gpio_bat = TOSA_GPIO_BAT1_V_ON,
+ .adc_bat = WM97XX_AUX_ID3,
+ .adc_bat_divider = 414,
+ .bat_max = 4310000,
+ .bat_min = 1551 * 1000000 / 414,
+
+ .gpio_temp = TOSA_GPIO_BAT0_TH_ON,
+ .adc_temp = WM97XX_AUX_ID2,
+ .adc_temp_divider = 10000,
+};
+
+static struct tosa_bat tosa_bat_bu = {
+ .status = POWER_SUPPLY_STATUS_UNKNOWN,
+ .full_chrg = -1,
+
+ .psy = {
+ .name = "backup-battery",
+ .type = POWER_SUPPLY_TYPE_BATTERY,
+ .properties = tosa_bat_bu_props,
+ .num_properties = ARRAY_SIZE(tosa_bat_bu_props),
+ .get_property = tosa_bat_get_property,
+ .external_power_changed = tosa_bat_external_power_changed,
+ },
+
+ .gpio_full = -1,
+ .gpio_charge_off = -1,
+
+ .technology = POWER_SUPPLY_TECHNOLOGY_LiMn,
+
+ .gpio_bat = TOSA_GPIO_BU_CHRG_ON,
+ .adc_bat = WM97XX_AUX_ID4,
+ .adc_bat_divider = 1266,
+
+ .gpio_temp = -1,
+ .adc_temp = -1,
+ .adc_temp_divider = -1,
+};
+
+static struct {
+ int gpio;
+ char *name;
+ bool output;
+ int value;
+} gpios[] = {
+ { TOSA_GPIO_CHARGE_OFF, "main charge off", 1, 1 },
+ { TOSA_GPIO_CHARGE_OFF_JC, "jacket charge off", 1, 1 },
+ { TOSA_GPIO_BAT_SW_ON, "battery switch", 1, 0 },
+ { TOSA_GPIO_BAT0_V_ON, "main battery", 1, 0 },
+ { TOSA_GPIO_BAT1_V_ON, "jacket battery", 1, 0 },
+ { TOSA_GPIO_BAT1_TH_ON, "main battery temp", 1, 0 },
+ { TOSA_GPIO_BAT0_TH_ON, "jacket battery temp", 1, 0 },
+ { TOSA_GPIO_BU_CHRG_ON, "backup battery", 1, 0 },
+ { TOSA_GPIO_BAT0_CRG, "main battery full", 0, 0 },
+ { TOSA_GPIO_BAT1_CRG, "jacket battery full", 0, 0 },
+ { TOSA_GPIO_BAT0_LOW, "main battery low", 0, 0 },
+ { TOSA_GPIO_BAT1_LOW, "jacket battery low", 0, 0 },
+ { TOSA_GPIO_JACKET_DETECT, "jacket detect", 0, 0 },
+};
+
+#ifdef CONFIG_PM
+static int tosa_bat_suspend(struct platform_device *dev, pm_message_t state)
+{
+ /* flush all pending status updates */
+ flush_scheduled_work();
+ return 0;
+}
+
+static int tosa_bat_resume(struct platform_device *dev)
+{
+ /* things may have changed while we were away */
+ schedule_work(&bat_work);
+ return 0;
+}
+#else
+#define tosa_bat_suspend NULL
+#define tosa_bat_resume NULL
+#endif
+
+static int __devinit tosa_bat_probe(struct platform_device *dev)
+{
+ int ret;
+ int i;
+
+ if (!machine_is_tosa())
+ return -ENODEV;
+
+ for (i = 0; i < ARRAY_SIZE(gpios); i++) {
+ ret = gpio_request(gpios[i].gpio, gpios[i].name);
+ if (ret) {
+ i--;
+ goto err_gpio;
+ }
+
+ if (gpios[i].output)
+ ret = gpio_direction_output(gpios[i].gpio,
+ gpios[i].value);
+ else
+ ret = gpio_direction_input(gpios[i].gpio);
+
+ if (ret)
+ goto err_gpio;
+ }
+
+ mutex_init(&tosa_bat_main.work_lock);
+ mutex_init(&tosa_bat_jacket.work_lock);
+
+ INIT_WORK(&bat_work, tosa_bat_work);
+
+ ret = power_supply_register(&dev->dev, &tosa_bat_main.psy);
+ if (ret)
+ goto err_psy_reg_main;
+ ret = power_supply_register(&dev->dev, &tosa_bat_jacket.psy);
+ if (ret)
+ goto err_psy_reg_jacket;
+ ret = power_supply_register(&dev->dev, &tosa_bat_bu.psy);
+ if (ret)
+ goto err_psy_reg_bu;
+
+ ret = request_irq(gpio_to_irq(TOSA_GPIO_BAT0_CRG),
+ tosa_bat_gpio_isr,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "main full", &tosa_bat_main);
+ if (ret)
+ goto err_req_main;
+
+ ret = request_irq(gpio_to_irq(TOSA_GPIO_BAT1_CRG),
+ tosa_bat_gpio_isr,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "jacket full", &tosa_bat_jacket);
+ if (ret)
+ goto err_req_jacket;
+
+ ret = request_irq(gpio_to_irq(TOSA_GPIO_JACKET_DETECT),
+ tosa_bat_gpio_isr,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "jacket detect", &tosa_bat_jacket);
+ if (!ret) {
+ schedule_work(&bat_work);
+ return 0;
+ }
+
+ free_irq(gpio_to_irq(TOSA_GPIO_BAT1_CRG), &tosa_bat_jacket);
+err_req_jacket:
+ free_irq(gpio_to_irq(TOSA_GPIO_BAT0_CRG), &tosa_bat_main);
+err_req_main:
+ power_supply_unregister(&tosa_bat_bu.psy);
+err_psy_reg_bu:
+ power_supply_unregister(&tosa_bat_jacket.psy);
+err_psy_reg_jacket:
+ power_supply_unregister(&tosa_bat_main.psy);
+err_psy_reg_main:
+
+ /* see comment in tosa_bat_remove */
+ flush_scheduled_work();
+
+ i--;
+err_gpio:
+ for (; i >= 0; i--)
+ gpio_free(gpios[i].gpio);
+
+ return ret;
+}
+
+static int __devexit tosa_bat_remove(struct platform_device *dev)
+{
+ int i;
+
+ free_irq(gpio_to_irq(TOSA_GPIO_JACKET_DETECT), &tosa_bat_jacket);
+ free_irq(gpio_to_irq(TOSA_GPIO_BAT1_CRG), &tosa_bat_jacket);
+ free_irq(gpio_to_irq(TOSA_GPIO_BAT0_CRG), &tosa_bat_main);
+
+ power_supply_unregister(&tosa_bat_bu.psy);
+ power_supply_unregister(&tosa_bat_jacket.psy);
+ power_supply_unregister(&tosa_bat_main.psy);
+
+ /*
+ * now flush all pending work.
+ * we won't get any more schedules, since all
+ * sources (isr and external_power_changed)
+ * are unregistered now.
+ */
+ flush_scheduled_work();
+
+ for (i = ARRAY_SIZE(gpios) - 1; i >= 0; i--)
+ gpio_free(gpios[i].gpio);
+
+ return 0;
+}
+
+static struct platform_driver tosa_bat_driver = {
+ .driver.name = "wm97xx-battery",
+ .driver.owner = THIS_MODULE,
+ .probe = tosa_bat_probe,
+ .remove = __devexit_p(tosa_bat_remove),
+ .suspend = tosa_bat_suspend,
+ .resume = tosa_bat_resume,
+};
+
+static int __init tosa_bat_init(void)
+{
+ return platform_driver_register(&tosa_bat_driver);
+}
+
+static void __exit tosa_bat_exit(void)
+{
+ platform_driver_unregister(&tosa_bat_driver);
+}
+
+module_init(tosa_bat_init);
+module_exit(tosa_bat_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Dmitry Baryshkov");
+MODULE_DESCRIPTION("Tosa battery driver");
+MODULE_ALIAS("platform:wm97xx-battery");
--- /dev/null
+menu "Voltage and Current regulators"
+
+config REGULATOR
+ bool "Voltage and Current Regulator Support"
+ default n
+ help
+ Generic Voltage and Current Regulator support.
+
+ This framework is designed to provide a generic interface to voltage
+ and current regulators within the Linux kernel. It's intended to
+ provide voltage and current control to client or consumer drivers and
+ also provide status information to user space applications through a
+ sysfs interface.
+
+ The intention is to allow systems to dynamically control regulator
+ output in order to save power and prolong battery life. This applies
+ to both voltage regulators (where voltage output is controllable) and
+ current sinks (where current output is controllable).
+
+ This framework safely compiles out if not selected so that client
+ drivers can still be used in systems with no software controllable
+ regulators.
+
+ If unsure, say no.
+
+config REGULATOR_DEBUG
+ bool "Regulator debug support"
+ depends on REGULATOR
+ help
+ Say yes here to enable debugging support.
+
+config REGULATOR_FIXED_VOLTAGE
+ tristate
+ default n
+ select REGULATOR
+
+config REGULATOR_VIRTUAL_CONSUMER
+ tristate "Virtual regulator consumer support"
+ default n
+ select REGULATOR
+ help
+ This driver provides a virtual consumer for the voltage and
+ current regulator API which provides sysfs controls for
+ configuring the supplies requested. This is mainly useful
+ for test purposes.
+
+ If unsure, say no.
+
+config REGULATOR_BQ24022
+ tristate "TI bq24022 Dual Input 1-Cell Li-Ion Charger IC"
+ default n
+ select REGULATOR
+ help
+ This driver controls a TI bq24022 Charger attached via
+ GPIOs. The provided current regulator can enable/disable
+ charging select between 100 mA and 500 mA charging current
+ limit.
+
+endmenu
--- /dev/null
+#
+# Makefile for regulator drivers.
+#
+
+
+obj-$(CONFIG_REGULATOR) += core.o
+obj-$(CONFIG_REGULATOR_FIXED_VOLTAGE) += fixed.o
+obj-$(CONFIG_REGULATOR_VIRTUAL_CONSUMER) += virtual.o
+
+obj-$(CONFIG_REGULATOR_BQ24022) += bq24022.o
+
+ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG
--- /dev/null
+/*
+ * Support for TI bq24022 (bqTINY-II) Dual Input (USB/AC Adpater)
+ * 1-Cell Li-Ion Charger connected via GPIOs.
+ *
+ * Copyright (c) 2008 Philipp Zabel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/regulator/bq24022.h>
+#include <linux/regulator/driver.h>
+
+static int bq24022_set_current_limit(struct regulator_dev *rdev,
+ int min_uA, int max_uA)
+{
+ struct platform_device *pdev = rdev_get_drvdata(rdev);
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+
+ dev_dbg(&pdev->dev, "setting current limit to %s mA\n",
+ max_uA >= 500000 ? "500" : "100");
+
+ /* REVISIT: maybe return error if min_uA != 0 ? */
+ gpio_set_value(pdata->gpio_iset2, max_uA >= 500000);
+ return 0;
+}
+
+static int bq24022_get_current_limit(struct regulator_dev *rdev)
+{
+ struct platform_device *pdev = rdev_get_drvdata(rdev);
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+
+ return gpio_get_value(pdata->gpio_iset2) ? 500000 : 100000;
+}
+
+static int bq24022_enable(struct regulator_dev *rdev)
+{
+ struct platform_device *pdev = rdev_get_drvdata(rdev);
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+
+ dev_dbg(&pdev->dev, "enabling charger\n");
+
+ gpio_set_value(pdata->gpio_nce, 0);
+ return 0;
+}
+
+static int bq24022_disable(struct regulator_dev *rdev)
+{
+ struct platform_device *pdev = rdev_get_drvdata(rdev);
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+
+ dev_dbg(&pdev->dev, "disabling charger\n");
+
+ gpio_set_value(pdata->gpio_nce, 1);
+ return 0;
+}
+
+static int bq24022_is_enabled(struct regulator_dev *rdev)
+{
+ struct platform_device *pdev = rdev_get_drvdata(rdev);
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+
+ return !gpio_get_value(pdata->gpio_nce);
+}
+
+static struct regulator_ops bq24022_ops = {
+ .set_current_limit = bq24022_set_current_limit,
+ .get_current_limit = bq24022_get_current_limit,
+ .enable = bq24022_enable,
+ .disable = bq24022_disable,
+ .is_enabled = bq24022_is_enabled,
+};
+
+static struct regulator_desc bq24022_desc = {
+ .name = "bq24022",
+ .ops = &bq24022_ops,
+ .type = REGULATOR_CURRENT,
+};
+
+static int __init bq24022_probe(struct platform_device *pdev)
+{
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+ struct regulator_dev *bq24022;
+ int ret;
+
+ if (!pdata || !pdata->gpio_nce || !pdata->gpio_iset2)
+ return -EINVAL;
+
+ ret = gpio_request(pdata->gpio_nce, "ncharge_en");
+ if (ret) {
+ dev_dbg(&pdev->dev, "couldn't request nCE GPIO: %d\n",
+ pdata->gpio_nce);
+ goto err_ce;
+ }
+ ret = gpio_request(pdata->gpio_iset2, "charge_mode");
+ if (ret) {
+ dev_dbg(&pdev->dev, "couldn't request ISET2 GPIO: %d\n",
+ pdata->gpio_iset2);
+ goto err_iset2;
+ }
+ ret = gpio_direction_output(pdata->gpio_iset2, 0);
+ ret = gpio_direction_output(pdata->gpio_nce, 1);
+
+ bq24022 = regulator_register(&bq24022_desc, pdev);
+ if (IS_ERR(bq24022)) {
+ dev_dbg(&pdev->dev, "couldn't register regulator\n");
+ ret = PTR_ERR(bq24022);
+ goto err_reg;
+ }
+ platform_set_drvdata(pdev, bq24022);
+ dev_dbg(&pdev->dev, "registered regulator\n");
+
+ return 0;
+err_reg:
+ gpio_free(pdata->gpio_iset2);
+err_iset2:
+ gpio_free(pdata->gpio_nce);
+err_ce:
+ return ret;
+}
+
+static int __devexit bq24022_remove(struct platform_device *pdev)
+{
+ struct bq24022_mach_info *pdata = pdev->dev.platform_data;
+ struct regulator_dev *bq24022 = platform_get_drvdata(pdev);
+
+ regulator_unregister(bq24022);
+ gpio_free(pdata->gpio_iset2);
+ gpio_free(pdata->gpio_nce);
+
+ return 0;
+}
+
+static struct platform_driver bq24022_driver = {
+ .driver = {
+ .name = "bq24022",
+ },
+ .remove = __devexit_p(bq24022_remove),
+};
+
+static int __init bq24022_init(void)
+{
+ return platform_driver_probe(&bq24022_driver, bq24022_probe);
+}
+
+static void __exit bq24022_exit(void)
+{
+ platform_driver_unregister(&bq24022_driver);
+}
+
+/*
+ * make sure this is probed before gpio_vbus and pda_power,
+ * but after asic3 or other GPIO expander drivers.
+ */
+subsys_initcall(bq24022_init);
+module_exit(bq24022_exit);
+
+MODULE_AUTHOR("Philipp Zabel");
+MODULE_DESCRIPTION("TI bq24022 Li-Ion Charger driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * core.c -- Voltage/Current Regulator framework.
+ *
+ * Copyright 2007, 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/suspend.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#define REGULATOR_VERSION "0.5"
+
+static DEFINE_MUTEX(regulator_list_mutex);
+static LIST_HEAD(regulator_list);
+static LIST_HEAD(regulator_map_list);
+
+/**
+ * struct regulator_dev
+ *
+ * Voltage / Current regulator class device. One for each regulator.
+ */
+struct regulator_dev {
+ struct regulator_desc *desc;
+ int use_count;
+
+ /* lists we belong to */
+ struct list_head list; /* list of all regulators */
+ struct list_head slist; /* list of supplied regulators */
+
+ /* lists we own */
+ struct list_head consumer_list; /* consumers we supply */
+ struct list_head supply_list; /* regulators we supply */
+
+ struct blocking_notifier_head notifier;
+ struct mutex mutex; /* consumer lock */
+ struct module *owner;
+ struct device dev;
+ struct regulation_constraints *constraints;
+ struct regulator_dev *supply; /* for tree */
+
+ void *reg_data; /* regulator_dev data */
+};
+
+/**
+ * struct regulator_map
+ *
+ * Used to provide symbolic supply names to devices.
+ */
+struct regulator_map {
+ struct list_head list;
+ struct device *dev;
+ const char *supply;
+ const char *regulator;
+};
+
+static inline struct regulator_dev *to_rdev(struct device *d)
+{
+ return container_of(d, struct regulator_dev, dev);
+}
+
+/*
+ * struct regulator
+ *
+ * One for each consumer device.
+ */
+struct regulator {
+ struct device *dev;
+ struct list_head list;
+ int uA_load;
+ int min_uV;
+ int max_uV;
+ int enabled; /* client has called enabled */
+ char *supply_name;
+ struct device_attribute dev_attr;
+ struct regulator_dev *rdev;
+};
+
+static int _regulator_is_enabled(struct regulator_dev *rdev);
+static int _regulator_disable(struct regulator_dev *rdev);
+static int _regulator_get_voltage(struct regulator_dev *rdev);
+static int _regulator_get_current_limit(struct regulator_dev *rdev);
+static unsigned int _regulator_get_mode(struct regulator_dev *rdev);
+static void _notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data);
+
+/* gets the regulator for a given consumer device */
+static struct regulator *get_device_regulator(struct device *dev)
+{
+ struct regulator *regulator = NULL;
+ struct regulator_dev *rdev;
+
+ mutex_lock(®ulator_list_mutex);
+ list_for_each_entry(rdev, ®ulator_list, list) {
+ mutex_lock(&rdev->mutex);
+ list_for_each_entry(regulator, &rdev->consumer_list, list) {
+ if (regulator->dev == dev) {
+ mutex_unlock(&rdev->mutex);
+ mutex_unlock(®ulator_list_mutex);
+ return regulator;
+ }
+ }
+ mutex_unlock(&rdev->mutex);
+ }
+ mutex_unlock(®ulator_list_mutex);
+ return NULL;
+}
+
+/* Platform voltage constraint check */
+static int regulator_check_voltage(struct regulator_dev *rdev,
+ int *min_uV, int *max_uV)
+{
+ BUG_ON(*min_uV > *max_uV);
+
+ if (!rdev->constraints) {
+ printk(KERN_ERR "%s: no constraints for %s\n", __func__,
+ rdev->desc->name);
+ return -ENODEV;
+ }
+ if (!(rdev->constraints->valid_ops_mask & REGULATOR_CHANGE_VOLTAGE)) {
+ printk(KERN_ERR "%s: operation not allowed for %s\n",
+ __func__, rdev->desc->name);
+ return -EPERM;
+ }
+
+ if (*max_uV > rdev->constraints->max_uV)
+ *max_uV = rdev->constraints->max_uV;
+ if (*min_uV < rdev->constraints->min_uV)
+ *min_uV = rdev->constraints->min_uV;
+
+ if (*min_uV > *max_uV)
+ return -EINVAL;
+
+ return 0;
+}
+
+/* current constraint check */
+static int regulator_check_current_limit(struct regulator_dev *rdev,
+ int *min_uA, int *max_uA)
+{
+ BUG_ON(*min_uA > *max_uA);
+
+ if (!rdev->constraints) {
+ printk(KERN_ERR "%s: no constraints for %s\n", __func__,
+ rdev->desc->name);
+ return -ENODEV;
+ }
+ if (!(rdev->constraints->valid_ops_mask & REGULATOR_CHANGE_CURRENT)) {
+ printk(KERN_ERR "%s: operation not allowed for %s\n",
+ __func__, rdev->desc->name);
+ return -EPERM;
+ }
+
+ if (*max_uA > rdev->constraints->max_uA)
+ *max_uA = rdev->constraints->max_uA;
+ if (*min_uA < rdev->constraints->min_uA)
+ *min_uA = rdev->constraints->min_uA;
+
+ if (*min_uA > *max_uA)
+ return -EINVAL;
+
+ return 0;
+}
+
+/* operating mode constraint check */
+static int regulator_check_mode(struct regulator_dev *rdev, int mode)
+{
+ if (!rdev->constraints) {
+ printk(KERN_ERR "%s: no constraints for %s\n", __func__,
+ rdev->desc->name);
+ return -ENODEV;
+ }
+ if (!(rdev->constraints->valid_ops_mask & REGULATOR_CHANGE_MODE)) {
+ printk(KERN_ERR "%s: operation not allowed for %s\n",
+ __func__, rdev->desc->name);
+ return -EPERM;
+ }
+ if (!(rdev->constraints->valid_modes_mask & mode)) {
+ printk(KERN_ERR "%s: invalid mode %x for %s\n",
+ __func__, mode, rdev->desc->name);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+/* dynamic regulator mode switching constraint check */
+static int regulator_check_drms(struct regulator_dev *rdev)
+{
+ if (!rdev->constraints) {
+ printk(KERN_ERR "%s: no constraints for %s\n", __func__,
+ rdev->desc->name);
+ return -ENODEV;
+ }
+ if (!(rdev->constraints->valid_ops_mask & REGULATOR_CHANGE_DRMS)) {
+ printk(KERN_ERR "%s: operation not allowed for %s\n",
+ __func__, rdev->desc->name);
+ return -EPERM;
+ }
+ return 0;
+}
+
+static ssize_t device_requested_uA_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator *regulator;
+
+ regulator = get_device_regulator(dev);
+ if (regulator == NULL)
+ return 0;
+
+ return sprintf(buf, "%d\n", regulator->uA_load);
+}
+
+static ssize_t regulator_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ ssize_t ret;
+
+ mutex_lock(&rdev->mutex);
+ ret = sprintf(buf, "%d\n", _regulator_get_voltage(rdev));
+ mutex_unlock(&rdev->mutex);
+
+ return ret;
+}
+
+static ssize_t regulator_uA_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ return sprintf(buf, "%d\n", _regulator_get_current_limit(rdev));
+}
+
+static ssize_t regulator_opmode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ int mode = _regulator_get_mode(rdev);
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return sprintf(buf, "fast\n");
+ case REGULATOR_MODE_NORMAL:
+ return sprintf(buf, "normal\n");
+ case REGULATOR_MODE_IDLE:
+ return sprintf(buf, "idle\n");
+ case REGULATOR_MODE_STANDBY:
+ return sprintf(buf, "standby\n");
+ }
+ return sprintf(buf, "unknown\n");
+}
+
+static ssize_t regulator_state_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ int state = _regulator_is_enabled(rdev);
+
+ if (state > 0)
+ return sprintf(buf, "enabled\n");
+ else if (state == 0)
+ return sprintf(buf, "disabled\n");
+ else
+ return sprintf(buf, "unknown\n");
+}
+
+static ssize_t regulator_min_uA_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "constraint not defined\n");
+
+ return sprintf(buf, "%d\n", rdev->constraints->min_uA);
+}
+
+static ssize_t regulator_max_uA_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "constraint not defined\n");
+
+ return sprintf(buf, "%d\n", rdev->constraints->max_uA);
+}
+
+static ssize_t regulator_min_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "constraint not defined\n");
+
+ return sprintf(buf, "%d\n", rdev->constraints->min_uV);
+}
+
+static ssize_t regulator_max_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "constraint not defined\n");
+
+ return sprintf(buf, "%d\n", rdev->constraints->max_uV);
+}
+
+static ssize_t regulator_total_uA_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ struct regulator *regulator;
+ int uA = 0;
+
+ mutex_lock(&rdev->mutex);
+ list_for_each_entry(regulator, &rdev->consumer_list, list)
+ uA += regulator->uA_load;
+ mutex_unlock(&rdev->mutex);
+ return sprintf(buf, "%d\n", uA);
+}
+
+static ssize_t regulator_num_users_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ return sprintf(buf, "%d\n", rdev->use_count);
+}
+
+static ssize_t regulator_type_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ switch (rdev->desc->type) {
+ case REGULATOR_VOLTAGE:
+ return sprintf(buf, "voltage\n");
+ case REGULATOR_CURRENT:
+ return sprintf(buf, "current\n");
+ }
+ return sprintf(buf, "unknown\n");
+}
+
+static ssize_t regulator_suspend_mem_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return sprintf(buf, "%d\n", rdev->constraints->state_mem.uV);
+}
+
+static ssize_t regulator_suspend_disk_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return sprintf(buf, "%d\n", rdev->constraints->state_disk.uV);
+}
+
+static ssize_t regulator_suspend_standby_uV_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return sprintf(buf, "%d\n", rdev->constraints->state_standby.uV);
+}
+
+static ssize_t suspend_opmode_show(struct regulator_dev *rdev,
+ unsigned int mode, char *buf)
+{
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return sprintf(buf, "fast\n");
+ case REGULATOR_MODE_NORMAL:
+ return sprintf(buf, "normal\n");
+ case REGULATOR_MODE_IDLE:
+ return sprintf(buf, "idle\n");
+ case REGULATOR_MODE_STANDBY:
+ return sprintf(buf, "standby\n");
+ }
+ return sprintf(buf, "unknown\n");
+}
+
+static ssize_t regulator_suspend_mem_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return suspend_opmode_show(rdev,
+ rdev->constraints->state_mem.mode, buf);
+}
+
+static ssize_t regulator_suspend_disk_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return suspend_opmode_show(rdev,
+ rdev->constraints->state_disk.mode, buf);
+}
+
+static ssize_t regulator_suspend_standby_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+ return suspend_opmode_show(rdev,
+ rdev->constraints->state_standby.mode, buf);
+}
+
+static ssize_t regulator_suspend_mem_state_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+
+ if (rdev->constraints->state_mem.enabled)
+ return sprintf(buf, "enabled\n");
+ else
+ return sprintf(buf, "disabled\n");
+}
+
+static ssize_t regulator_suspend_disk_state_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+
+ if (rdev->constraints->state_disk.enabled)
+ return sprintf(buf, "enabled\n");
+ else
+ return sprintf(buf, "disabled\n");
+}
+
+static ssize_t regulator_suspend_standby_state_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+
+ if (!rdev->constraints)
+ return sprintf(buf, "not defined\n");
+
+ if (rdev->constraints->state_standby.enabled)
+ return sprintf(buf, "enabled\n");
+ else
+ return sprintf(buf, "disabled\n");
+}
+static struct device_attribute regulator_dev_attrs[] = {
+ __ATTR(microvolts, 0444, regulator_uV_show, NULL),
+ __ATTR(microamps, 0444, regulator_uA_show, NULL),
+ __ATTR(opmode, 0444, regulator_opmode_show, NULL),
+ __ATTR(state, 0444, regulator_state_show, NULL),
+ __ATTR(min_microvolts, 0444, regulator_min_uV_show, NULL),
+ __ATTR(min_microamps, 0444, regulator_min_uA_show, NULL),
+ __ATTR(max_microvolts, 0444, regulator_max_uV_show, NULL),
+ __ATTR(max_microamps, 0444, regulator_max_uA_show, NULL),
+ __ATTR(requested_microamps, 0444, regulator_total_uA_show, NULL),
+ __ATTR(num_users, 0444, regulator_num_users_show, NULL),
+ __ATTR(type, 0444, regulator_type_show, NULL),
+ __ATTR(suspend_mem_microvolts, 0444,
+ regulator_suspend_mem_uV_show, NULL),
+ __ATTR(suspend_disk_microvolts, 0444,
+ regulator_suspend_disk_uV_show, NULL),
+ __ATTR(suspend_standby_microvolts, 0444,
+ regulator_suspend_standby_uV_show, NULL),
+ __ATTR(suspend_mem_mode, 0444,
+ regulator_suspend_mem_mode_show, NULL),
+ __ATTR(suspend_disk_mode, 0444,
+ regulator_suspend_disk_mode_show, NULL),
+ __ATTR(suspend_standby_mode, 0444,
+ regulator_suspend_standby_mode_show, NULL),
+ __ATTR(suspend_mem_state, 0444,
+ regulator_suspend_mem_state_show, NULL),
+ __ATTR(suspend_disk_state, 0444,
+ regulator_suspend_disk_state_show, NULL),
+ __ATTR(suspend_standby_state, 0444,
+ regulator_suspend_standby_state_show, NULL),
+ __ATTR_NULL,
+};
+
+static void regulator_dev_release(struct device *dev)
+{
+ struct regulator_dev *rdev = to_rdev(dev);
+ kfree(rdev);
+}
+
+static struct class regulator_class = {
+ .name = "regulator",
+ .dev_release = regulator_dev_release,
+ .dev_attrs = regulator_dev_attrs,
+};
+
+/* Calculate the new optimum regulator operating mode based on the new total
+ * consumer load. All locks held by caller */
+static void drms_uA_update(struct regulator_dev *rdev)
+{
+ struct regulator *sibling;
+ int current_uA = 0, output_uV, input_uV, err;
+ unsigned int mode;
+
+ err = regulator_check_drms(rdev);
+ if (err < 0 || !rdev->desc->ops->get_optimum_mode ||
+ !rdev->desc->ops->get_voltage || !rdev->desc->ops->set_mode);
+ return;
+
+ /* get output voltage */
+ output_uV = rdev->desc->ops->get_voltage(rdev);
+ if (output_uV <= 0)
+ return;
+
+ /* get input voltage */
+ if (rdev->supply && rdev->supply->desc->ops->get_voltage)
+ input_uV = rdev->supply->desc->ops->get_voltage(rdev->supply);
+ else
+ input_uV = rdev->constraints->input_uV;
+ if (input_uV <= 0)
+ return;
+
+ /* calc total requested load */
+ list_for_each_entry(sibling, &rdev->consumer_list, list)
+ current_uA += sibling->uA_load;
+
+ /* now get the optimum mode for our new total regulator load */
+ mode = rdev->desc->ops->get_optimum_mode(rdev, input_uV,
+ output_uV, current_uA);
+
+ /* check the new mode is allowed */
+ err = regulator_check_mode(rdev, mode);
+ if (err == 0)
+ rdev->desc->ops->set_mode(rdev, mode);
+}
+
+static int suspend_set_state(struct regulator_dev *rdev,
+ struct regulator_state *rstate)
+{
+ int ret = 0;
+
+ /* enable & disable are mandatory for suspend control */
+ if (!rdev->desc->ops->set_suspend_enable ||
+ !rdev->desc->ops->set_suspend_disable)
+ return -EINVAL;
+
+ if (rstate->enabled)
+ ret = rdev->desc->ops->set_suspend_enable(rdev);
+ else
+ ret = rdev->desc->ops->set_suspend_disable(rdev);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to enabled/disable\n", __func__);
+ return ret;
+ }
+
+ if (rdev->desc->ops->set_suspend_voltage && rstate->uV > 0) {
+ ret = rdev->desc->ops->set_suspend_voltage(rdev, rstate->uV);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to set voltage\n",
+ __func__);
+ return ret;
+ }
+ }
+
+ if (rdev->desc->ops->set_suspend_mode && rstate->mode > 0) {
+ ret = rdev->desc->ops->set_suspend_mode(rdev, rstate->mode);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to set mode\n", __func__);
+ return ret;
+ }
+ }
+ return ret;
+}
+
+/* locks held by caller */
+static int suspend_prepare(struct regulator_dev *rdev, suspend_state_t state)
+{
+ if (!rdev->constraints)
+ return -EINVAL;
+
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ return suspend_set_state(rdev,
+ &rdev->constraints->state_standby);
+ case PM_SUSPEND_MEM:
+ return suspend_set_state(rdev,
+ &rdev->constraints->state_mem);
+ case PM_SUSPEND_MAX:
+ return suspend_set_state(rdev,
+ &rdev->constraints->state_disk);
+ default:
+ return -EINVAL;
+ }
+}
+
+static void print_constraints(struct regulator_dev *rdev)
+{
+ struct regulation_constraints *constraints = rdev->constraints;
+ char buf[80];
+ int count;
+
+ if (rdev->desc->type == REGULATOR_VOLTAGE) {
+ if (constraints->min_uV == constraints->max_uV)
+ count = sprintf(buf, "%d mV ",
+ constraints->min_uV / 1000);
+ else
+ count = sprintf(buf, "%d <--> %d mV ",
+ constraints->min_uV / 1000,
+ constraints->max_uV / 1000);
+ } else {
+ if (constraints->min_uA == constraints->max_uA)
+ count = sprintf(buf, "%d mA ",
+ constraints->min_uA / 1000);
+ else
+ count = sprintf(buf, "%d <--> %d mA ",
+ constraints->min_uA / 1000,
+ constraints->max_uA / 1000);
+ }
+ if (constraints->valid_modes_mask & REGULATOR_MODE_FAST)
+ count += sprintf(buf + count, "fast ");
+ if (constraints->valid_modes_mask & REGULATOR_MODE_NORMAL)
+ count += sprintf(buf + count, "normal ");
+ if (constraints->valid_modes_mask & REGULATOR_MODE_IDLE)
+ count += sprintf(buf + count, "idle ");
+ if (constraints->valid_modes_mask & REGULATOR_MODE_STANDBY)
+ count += sprintf(buf + count, "standby");
+
+ printk(KERN_INFO "regulator: %s: %s\n", rdev->desc->name, buf);
+}
+
+#define REG_STR_SIZE 32
+
+static struct regulator *create_regulator(struct regulator_dev *rdev,
+ struct device *dev,
+ const char *supply_name)
+{
+ struct regulator *regulator;
+ char buf[REG_STR_SIZE];
+ int err, size;
+
+ regulator = kzalloc(sizeof(*regulator), GFP_KERNEL);
+ if (regulator == NULL)
+ return NULL;
+
+ mutex_lock(&rdev->mutex);
+ regulator->rdev = rdev;
+ list_add(®ulator->list, &rdev->consumer_list);
+
+ if (dev) {
+ /* create a 'requested_microamps_name' sysfs entry */
+ size = scnprintf(buf, REG_STR_SIZE, "microamps_requested_%s",
+ supply_name);
+ if (size >= REG_STR_SIZE)
+ goto overflow_err;
+
+ regulator->dev = dev;
+ regulator->dev_attr.attr.name = kstrdup(buf, GFP_KERNEL);
+ if (regulator->dev_attr.attr.name == NULL)
+ goto attr_name_err;
+
+ regulator->dev_attr.attr.owner = THIS_MODULE;
+ regulator->dev_attr.attr.mode = 0444;
+ regulator->dev_attr.show = device_requested_uA_show;
+ err = device_create_file(dev, ®ulator->dev_attr);
+ if (err < 0) {
+ printk(KERN_WARNING "%s: could not add regulator_dev"
+ " load sysfs\n", __func__);
+ goto attr_name_err;
+ }
+
+ /* also add a link to the device sysfs entry */
+ size = scnprintf(buf, REG_STR_SIZE, "%s-%s",
+ dev->kobj.name, supply_name);
+ if (size >= REG_STR_SIZE)
+ goto attr_err;
+
+ regulator->supply_name = kstrdup(buf, GFP_KERNEL);
+ if (regulator->supply_name == NULL)
+ goto attr_err;
+
+ err = sysfs_create_link(&rdev->dev.kobj, &dev->kobj,
+ buf);
+ if (err) {
+ printk(KERN_WARNING
+ "%s: could not add device link %s err %d\n",
+ __func__, dev->kobj.name, err);
+ device_remove_file(dev, ®ulator->dev_attr);
+ goto link_name_err;
+ }
+ }
+ mutex_unlock(&rdev->mutex);
+ return regulator;
+link_name_err:
+ kfree(regulator->supply_name);
+attr_err:
+ device_remove_file(regulator->dev, ®ulator->dev_attr);
+attr_name_err:
+ kfree(regulator->dev_attr.attr.name);
+overflow_err:
+ list_del(®ulator->list);
+ kfree(regulator);
+ mutex_unlock(&rdev->mutex);
+ return NULL;
+}
+
+/**
+ * regulator_get - lookup and obtain a reference to a regulator.
+ * @dev: device for regulator "consumer"
+ * @id: Supply name or regulator ID.
+ *
+ * Returns a struct regulator corresponding to the regulator producer,
+ * or IS_ERR() condition containing errno. Use of supply names
+ * configured via regulator_set_device_supply() is strongly
+ * encouraged.
+ */
+struct regulator *regulator_get(struct device *dev, const char *id)
+{
+ struct regulator_dev *rdev;
+ struct regulator_map *map;
+ struct regulator *regulator = ERR_PTR(-ENODEV);
+ const char *supply = id;
+
+ if (id == NULL) {
+ printk(KERN_ERR "regulator: get() with no identifier\n");
+ return regulator;
+ }
+
+ mutex_lock(®ulator_list_mutex);
+
+ list_for_each_entry(map, ®ulator_map_list, list) {
+ if (dev == map->dev &&
+ strcmp(map->supply, id) == 0) {
+ supply = map->regulator;
+ break;
+ }
+ }
+
+ list_for_each_entry(rdev, ®ulator_list, list) {
+ if (strcmp(supply, rdev->desc->name) == 0 &&
+ try_module_get(rdev->owner))
+ goto found;
+ }
+ printk(KERN_ERR "regulator: Unable to get requested regulator: %s\n",
+ id);
+ mutex_unlock(®ulator_list_mutex);
+ return regulator;
+
+found:
+ regulator = create_regulator(rdev, dev, id);
+ if (regulator == NULL) {
+ regulator = ERR_PTR(-ENOMEM);
+ module_put(rdev->owner);
+ }
+
+ mutex_unlock(®ulator_list_mutex);
+ return regulator;
+}
+EXPORT_SYMBOL_GPL(regulator_get);
+
+/**
+ * regulator_put - "free" the regulator source
+ * @regulator: regulator source
+ *
+ * Note: drivers must ensure that all regulator_enable calls made on this
+ * regulator source are balanced by regulator_disable calls prior to calling
+ * this function.
+ */
+void regulator_put(struct regulator *regulator)
+{
+ struct regulator_dev *rdev;
+
+ if (regulator == NULL || IS_ERR(regulator))
+ return;
+
+ if (regulator->enabled) {
+ printk(KERN_WARNING "Releasing supply %s while enabled\n",
+ regulator->supply_name);
+ WARN_ON(regulator->enabled);
+ regulator_disable(regulator);
+ }
+
+ mutex_lock(®ulator_list_mutex);
+ rdev = regulator->rdev;
+
+ /* remove any sysfs entries */
+ if (regulator->dev) {
+ sysfs_remove_link(&rdev->dev.kobj, regulator->supply_name);
+ kfree(regulator->supply_name);
+ device_remove_file(regulator->dev, ®ulator->dev_attr);
+ kfree(regulator->dev_attr.attr.name);
+ }
+ list_del(®ulator->list);
+ kfree(regulator);
+
+ module_put(rdev->owner);
+ mutex_unlock(®ulator_list_mutex);
+}
+EXPORT_SYMBOL_GPL(regulator_put);
+
+/* locks held by regulator_enable() */
+static int _regulator_enable(struct regulator_dev *rdev)
+{
+ int ret = -EINVAL;
+
+ if (!rdev->constraints) {
+ printk(KERN_ERR "%s: %s has no constraints\n",
+ __func__, rdev->desc->name);
+ return ret;
+ }
+
+ /* do we need to enable the supply regulator first */
+ if (rdev->supply) {
+ ret = _regulator_enable(rdev->supply);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to enable %s: %d\n",
+ __func__, rdev->desc->name, ret);
+ return ret;
+ }
+ }
+
+ /* check voltage and requested load before enabling */
+ if (rdev->desc->ops->enable) {
+
+ if (rdev->constraints &&
+ (rdev->constraints->valid_ops_mask &
+ REGULATOR_CHANGE_DRMS))
+ drms_uA_update(rdev);
+
+ ret = rdev->desc->ops->enable(rdev);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to enable %s: %d\n",
+ __func__, rdev->desc->name, ret);
+ return ret;
+ }
+ rdev->use_count++;
+ return ret;
+ }
+
+ return ret;
+}
+
+/**
+ * regulator_enable - enable regulator output
+ * @regulator: regulator source
+ *
+ * Enable the regulator output at the predefined voltage or current value.
+ * NOTE: the output value can be set by other drivers, boot loader or may be
+ * hardwired in the regulator.
+ * NOTE: calls to regulator_enable() must be balanced with calls to
+ * regulator_disable().
+ */
+int regulator_enable(struct regulator *regulator)
+{
+ int ret;
+
+ if (regulator->enabled) {
+ printk(KERN_CRIT "Regulator %s already enabled\n",
+ regulator->supply_name);
+ WARN_ON(regulator->enabled);
+ return 0;
+ }
+
+ mutex_lock(®ulator->rdev->mutex);
+ regulator->enabled = 1;
+ ret = _regulator_enable(regulator->rdev);
+ if (ret != 0)
+ regulator->enabled = 0;
+ mutex_unlock(®ulator->rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_enable);
+
+/* locks held by regulator_disable() */
+static int _regulator_disable(struct regulator_dev *rdev)
+{
+ int ret = 0;
+
+ /* are we the last user and permitted to disable ? */
+ if (rdev->use_count == 1 && !rdev->constraints->always_on) {
+
+ /* we are last user */
+ if (rdev->desc->ops->disable) {
+ ret = rdev->desc->ops->disable(rdev);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to disable %s\n",
+ __func__, rdev->desc->name);
+ return ret;
+ }
+ }
+
+ /* decrease our supplies ref count and disable if required */
+ if (rdev->supply)
+ _regulator_disable(rdev->supply);
+
+ rdev->use_count = 0;
+ } else if (rdev->use_count > 1) {
+
+ if (rdev->constraints &&
+ (rdev->constraints->valid_ops_mask &
+ REGULATOR_CHANGE_DRMS))
+ drms_uA_update(rdev);
+
+ rdev->use_count--;
+ }
+ return ret;
+}
+
+/**
+ * regulator_disable - disable regulator output
+ * @regulator: regulator source
+ *
+ * Disable the regulator output voltage or current.
+ * NOTE: this will only disable the regulator output if no other consumer
+ * devices have it enabled.
+ * NOTE: calls to regulator_enable() must be balanced with calls to
+ * regulator_disable().
+ */
+int regulator_disable(struct regulator *regulator)
+{
+ int ret;
+
+ if (!regulator->enabled) {
+ printk(KERN_ERR "%s: not in use by this consumer\n",
+ __func__);
+ return 0;
+ }
+
+ mutex_lock(®ulator->rdev->mutex);
+ regulator->enabled = 0;
+ regulator->uA_load = 0;
+ ret = _regulator_disable(regulator->rdev);
+ mutex_unlock(®ulator->rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_disable);
+
+/* locks held by regulator_force_disable() */
+static int _regulator_force_disable(struct regulator_dev *rdev)
+{
+ int ret = 0;
+
+ /* force disable */
+ if (rdev->desc->ops->disable) {
+ /* ah well, who wants to live forever... */
+ ret = rdev->desc->ops->disable(rdev);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to force disable %s\n",
+ __func__, rdev->desc->name);
+ return ret;
+ }
+ /* notify other consumers that power has been forced off */
+ _notifier_call_chain(rdev, REGULATOR_EVENT_FORCE_DISABLE,
+ NULL);
+ }
+
+ /* decrease our supplies ref count and disable if required */
+ if (rdev->supply)
+ _regulator_disable(rdev->supply);
+
+ rdev->use_count = 0;
+ return ret;
+}
+
+/**
+ * regulator_force_disable - force disable regulator output
+ * @regulator: regulator source
+ *
+ * Forcibly disable the regulator output voltage or current.
+ * NOTE: this *will* disable the regulator output even if other consumer
+ * devices have it enabled. This should be used for situations when device
+ * damage will likely occur if the regulator is not disabled (e.g. over temp).
+ */
+int regulator_force_disable(struct regulator *regulator)
+{
+ int ret;
+
+ mutex_lock(®ulator->rdev->mutex);
+ regulator->enabled = 0;
+ regulator->uA_load = 0;
+ ret = _regulator_force_disable(regulator->rdev);
+ mutex_unlock(®ulator->rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_force_disable);
+
+static int _regulator_is_enabled(struct regulator_dev *rdev)
+{
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->is_enabled) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = rdev->desc->ops->is_enabled(rdev);
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+
+/**
+ * regulator_is_enabled - is the regulator output enabled
+ * @regulator: regulator source
+ *
+ * Returns zero for disabled otherwise return number of enable requests.
+ */
+int regulator_is_enabled(struct regulator *regulator)
+{
+ return _regulator_is_enabled(regulator->rdev);
+}
+EXPORT_SYMBOL_GPL(regulator_is_enabled);
+
+/**
+ * regulator_set_voltage - set regulator output voltage
+ * @regulator: regulator source
+ * @min_uV: Minimum required voltage in uV
+ * @max_uV: Maximum acceptable voltage in uV
+ *
+ * Sets a voltage regulator to the desired output voltage. This can be set
+ * during any regulator state. IOW, regulator can be disabled or enabled.
+ *
+ * If the regulator is enabled then the voltage will change to the new value
+ * immediately otherwise if the regulator is disabled the regulator will
+ * output at the new voltage when enabled.
+ *
+ * NOTE: If the regulator is shared between several devices then the lowest
+ * request voltage that meets the system constraints will be used.
+ * NOTE: Regulator system constraints must be set for this regulator before
+ * calling this function otherwise this call will fail.
+ */
+int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->set_voltage) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* constraints check */
+ ret = regulator_check_voltage(rdev, &min_uV, &max_uV);
+ if (ret < 0)
+ goto out;
+ regulator->min_uV = min_uV;
+ regulator->max_uV = max_uV;
+ ret = rdev->desc->ops->set_voltage(rdev, min_uV, max_uV);
+
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_voltage);
+
+static int _regulator_get_voltage(struct regulator_dev *rdev)
+{
+ /* sanity check */
+ if (rdev->desc->ops->get_voltage)
+ return rdev->desc->ops->get_voltage(rdev);
+ else
+ return -EINVAL;
+}
+
+/**
+ * regulator_get_voltage - get regulator output voltage
+ * @regulator: regulator source
+ *
+ * This returns the current regulator voltage in uV.
+ *
+ * NOTE: If the regulator is disabled it will return the voltage value. This
+ * function should not be used to determine regulator state.
+ */
+int regulator_get_voltage(struct regulator *regulator)
+{
+ int ret;
+
+ mutex_lock(®ulator->rdev->mutex);
+
+ ret = _regulator_get_voltage(regulator->rdev);
+
+ mutex_unlock(®ulator->rdev->mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_get_voltage);
+
+/**
+ * regulator_set_current_limit - set regulator output current limit
+ * @regulator: regulator source
+ * @min_uA: Minimuum supported current in uA
+ * @max_uA: Maximum supported current in uA
+ *
+ * Sets current sink to the desired output current. This can be set during
+ * any regulator state. IOW, regulator can be disabled or enabled.
+ *
+ * If the regulator is enabled then the current will change to the new value
+ * immediately otherwise if the regulator is disabled the regulator will
+ * output at the new current when enabled.
+ *
+ * NOTE: Regulator system constraints must be set for this regulator before
+ * calling this function otherwise this call will fail.
+ */
+int regulator_set_current_limit(struct regulator *regulator,
+ int min_uA, int max_uA)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->set_current_limit) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* constraints check */
+ ret = regulator_check_current_limit(rdev, &min_uA, &max_uA);
+ if (ret < 0)
+ goto out;
+
+ ret = rdev->desc->ops->set_current_limit(rdev, min_uA, max_uA);
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_current_limit);
+
+static int _regulator_get_current_limit(struct regulator_dev *rdev)
+{
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->get_current_limit) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = rdev->desc->ops->get_current_limit(rdev);
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+
+/**
+ * regulator_get_current_limit - get regulator output current
+ * @regulator: regulator source
+ *
+ * This returns the current supplied by the specified current sink in uA.
+ *
+ * NOTE: If the regulator is disabled it will return the current value. This
+ * function should not be used to determine regulator state.
+ */
+int regulator_get_current_limit(struct regulator *regulator)
+{
+ return _regulator_get_current_limit(regulator->rdev);
+}
+EXPORT_SYMBOL_GPL(regulator_get_current_limit);
+
+/**
+ * regulator_set_mode - set regulator operating mode
+ * @regulator: regulator source
+ * @mode: operating mode - one of the REGULATOR_MODE constants
+ *
+ * Set regulator operating mode to increase regulator efficiency or improve
+ * regulation performance.
+ *
+ * NOTE: Regulator system constraints must be set for this regulator before
+ * calling this function otherwise this call will fail.
+ */
+int regulator_set_mode(struct regulator *regulator, unsigned int mode)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->set_mode) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* constraints check */
+ ret = regulator_check_mode(rdev, mode);
+ if (ret < 0)
+ goto out;
+
+ ret = rdev->desc->ops->set_mode(rdev, mode);
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_mode);
+
+static unsigned int _regulator_get_mode(struct regulator_dev *rdev)
+{
+ int ret;
+
+ mutex_lock(&rdev->mutex);
+
+ /* sanity check */
+ if (!rdev->desc->ops->get_mode) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = rdev->desc->ops->get_mode(rdev);
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+
+/**
+ * regulator_get_mode - get regulator operating mode
+ * @regulator: regulator source
+ *
+ * Get the current regulator operating mode.
+ */
+unsigned int regulator_get_mode(struct regulator *regulator)
+{
+ return _regulator_get_mode(regulator->rdev);
+}
+EXPORT_SYMBOL_GPL(regulator_get_mode);
+
+/**
+ * regulator_set_optimum_mode - set regulator optimum operating mode
+ * @regulator: regulator source
+ * @uA_load: load current
+ *
+ * Notifies the regulator core of a new device load. This is then used by
+ * DRMS (if enabled by constraints) to set the most efficient regulator
+ * operating mode for the new regulator loading.
+ *
+ * Consumer devices notify their supply regulator of the maximum power
+ * they will require (can be taken from device datasheet in the power
+ * consumption tables) when they change operational status and hence power
+ * state. Examples of operational state changes that can affect power
+ * consumption are :-
+ *
+ * o Device is opened / closed.
+ * o Device I/O is about to begin or has just finished.
+ * o Device is idling in between work.
+ *
+ * This information is also exported via sysfs to userspace.
+ *
+ * DRMS will sum the total requested load on the regulator and change
+ * to the most efficient operating mode if platform constraints allow.
+ *
+ * Returns the new regulator mode or error.
+ */
+int regulator_set_optimum_mode(struct regulator *regulator, int uA_load)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ struct regulator *consumer;
+ int ret, output_uV, input_uV, total_uA_load = 0;
+ unsigned int mode;
+
+ mutex_lock(&rdev->mutex);
+
+ regulator->uA_load = uA_load;
+ ret = regulator_check_drms(rdev);
+ if (ret < 0)
+ goto out;
+ ret = -EINVAL;
+
+ /* sanity check */
+ if (!rdev->desc->ops->get_optimum_mode)
+ goto out;
+
+ /* get output voltage */
+ output_uV = rdev->desc->ops->get_voltage(rdev);
+ if (output_uV <= 0) {
+ printk(KERN_ERR "%s: invalid output voltage found for %s\n",
+ __func__, rdev->desc->name);
+ goto out;
+ }
+
+ /* get input voltage */
+ if (rdev->supply && rdev->supply->desc->ops->get_voltage)
+ input_uV = rdev->supply->desc->ops->get_voltage(rdev->supply);
+ else
+ input_uV = rdev->constraints->input_uV;
+ if (input_uV <= 0) {
+ printk(KERN_ERR "%s: invalid input voltage found for %s\n",
+ __func__, rdev->desc->name);
+ goto out;
+ }
+
+ /* calc total requested load for this regulator */
+ list_for_each_entry(consumer, &rdev->consumer_list, list)
+ total_uA_load += consumer->uA_load;
+
+ mode = rdev->desc->ops->get_optimum_mode(rdev,
+ input_uV, output_uV,
+ total_uA_load);
+ if (ret <= 0) {
+ printk(KERN_ERR "%s: failed to get optimum mode for %s @"
+ " %d uA %d -> %d uV\n", __func__, rdev->desc->name,
+ total_uA_load, input_uV, output_uV);
+ goto out;
+ }
+
+ ret = rdev->desc->ops->set_mode(rdev, mode);
+ if (ret <= 0) {
+ printk(KERN_ERR "%s: failed to set optimum mode %x for %s\n",
+ __func__, mode, rdev->desc->name);
+ goto out;
+ }
+ ret = mode;
+out:
+ mutex_unlock(&rdev->mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_optimum_mode);
+
+/**
+ * regulator_register_notifier - register regulator event notifier
+ * @regulator: regulator source
+ * @notifier_block: notifier block
+ *
+ * Register notifier block to receive regulator events.
+ */
+int regulator_register_notifier(struct regulator *regulator,
+ struct notifier_block *nb)
+{
+ return blocking_notifier_chain_register(®ulator->rdev->notifier,
+ nb);
+}
+EXPORT_SYMBOL_GPL(regulator_register_notifier);
+
+/**
+ * regulator_unregister_notifier - unregister regulator event notifier
+ * @regulator: regulator source
+ * @notifier_block: notifier block
+ *
+ * Unregister regulator event notifier block.
+ */
+int regulator_unregister_notifier(struct regulator *regulator,
+ struct notifier_block *nb)
+{
+ return blocking_notifier_chain_unregister(®ulator->rdev->notifier,
+ nb);
+}
+EXPORT_SYMBOL_GPL(regulator_unregister_notifier);
+
+/* notify regulator consumers and downstream regulator consumers */
+static void _notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data)
+{
+ struct regulator_dev *_rdev;
+
+ /* call rdev chain first */
+ mutex_lock(&rdev->mutex);
+ blocking_notifier_call_chain(&rdev->notifier, event, NULL);
+ mutex_unlock(&rdev->mutex);
+
+ /* now notify regulator we supply */
+ list_for_each_entry(_rdev, &rdev->supply_list, slist)
+ _notifier_call_chain(_rdev, event, data);
+}
+
+/**
+ * regulator_bulk_get - get multiple regulator consumers
+ *
+ * @dev: Device to supply
+ * @num_consumers: Number of consumers to register
+ * @consumers: Configuration of consumers; clients are stored here.
+ *
+ * @return 0 on success, an errno on failure.
+ *
+ * This helper function allows drivers to get several regulator
+ * consumers in one operation. If any of the regulators cannot be
+ * acquired then any regulators that were allocated will be freed
+ * before returning to the caller.
+ */
+int regulator_bulk_get(struct device *dev, int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ int i;
+ int ret;
+
+ for (i = 0; i < num_consumers; i++)
+ consumers[i].consumer = NULL;
+
+ for (i = 0; i < num_consumers; i++) {
+ consumers[i].consumer = regulator_get(dev,
+ consumers[i].supply);
+ if (IS_ERR(consumers[i].consumer)) {
+ dev_err(dev, "Failed to get supply '%s'\n",
+ consumers[i].supply);
+ ret = PTR_ERR(consumers[i].consumer);
+ consumers[i].consumer = NULL;
+ goto err;
+ }
+ }
+
+ return 0;
+
+err:
+ for (i = 0; i < num_consumers && consumers[i].consumer; i++)
+ regulator_put(consumers[i].consumer);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_bulk_get);
+
+/**
+ * regulator_bulk_enable - enable multiple regulator consumers
+ *
+ * @num_consumers: Number of consumers
+ * @consumers: Consumer data; clients are stored here.
+ * @return 0 on success, an errno on failure
+ *
+ * This convenience API allows consumers to enable multiple regulator
+ * clients in a single API call. If any consumers cannot be enabled
+ * then any others that were enabled will be disabled again prior to
+ * return.
+ */
+int regulator_bulk_enable(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ int i;
+ int ret;
+
+ for (i = 0; i < num_consumers; i++) {
+ ret = regulator_enable(consumers[i].consumer);
+ if (ret != 0)
+ goto err;
+ }
+
+ return 0;
+
+err:
+ printk(KERN_ERR "Failed to enable %s\n", consumers[i].supply);
+ for (i = 0; i < num_consumers; i++)
+ regulator_disable(consumers[i].consumer);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_bulk_enable);
+
+/**
+ * regulator_bulk_disable - disable multiple regulator consumers
+ *
+ * @num_consumers: Number of consumers
+ * @consumers: Consumer data; clients are stored here.
+ * @return 0 on success, an errno on failure
+ *
+ * This convenience API allows consumers to disable multiple regulator
+ * clients in a single API call. If any consumers cannot be enabled
+ * then any others that were disabled will be disabled again prior to
+ * return.
+ */
+int regulator_bulk_disable(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ int i;
+ int ret;
+
+ for (i = 0; i < num_consumers; i++) {
+ ret = regulator_disable(consumers[i].consumer);
+ if (ret != 0)
+ goto err;
+ }
+
+ return 0;
+
+err:
+ printk(KERN_ERR "Failed to disable %s\n", consumers[i].supply);
+ for (i = 0; i < num_consumers; i++)
+ regulator_enable(consumers[i].consumer);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_bulk_disable);
+
+/**
+ * regulator_bulk_free - free multiple regulator consumers
+ *
+ * @num_consumers: Number of consumers
+ * @consumers: Consumer data; clients are stored here.
+ *
+ * This convenience API allows consumers to free multiple regulator
+ * clients in a single API call.
+ */
+void regulator_bulk_free(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ int i;
+
+ for (i = 0; i < num_consumers; i++) {
+ regulator_put(consumers[i].consumer);
+ consumers[i].consumer = NULL;
+ }
+}
+EXPORT_SYMBOL_GPL(regulator_bulk_free);
+
+/**
+ * regulator_notifier_call_chain - call regulator event notifier
+ * @regulator: regulator source
+ * @event: notifier block
+ * @data:
+ *
+ * Called by regulator drivers to notify clients a regulator event has
+ * occurred. We also notify regulator clients downstream.
+ */
+int regulator_notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data)
+{
+ _notifier_call_chain(rdev, event, data);
+ return NOTIFY_DONE;
+
+}
+EXPORT_SYMBOL_GPL(regulator_notifier_call_chain);
+
+/**
+ * regulator_register - register regulator
+ * @regulator: regulator source
+ * @reg_data: private regulator data
+ *
+ * Called by regulator drivers to register a regulator.
+ * Returns 0 on success.
+ */
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+ void *reg_data)
+{
+ static atomic_t regulator_no = ATOMIC_INIT(0);
+ struct regulator_dev *rdev;
+ int ret;
+
+ if (regulator_desc == NULL)
+ return ERR_PTR(-EINVAL);
+
+ if (regulator_desc->name == NULL || regulator_desc->ops == NULL)
+ return ERR_PTR(-EINVAL);
+
+ if (!regulator_desc->type == REGULATOR_VOLTAGE &&
+ !regulator_desc->type == REGULATOR_CURRENT)
+ return ERR_PTR(-EINVAL);
+
+ rdev = kzalloc(sizeof(struct regulator_dev), GFP_KERNEL);
+ if (rdev == NULL)
+ return ERR_PTR(-ENOMEM);
+
+ mutex_lock(®ulator_list_mutex);
+
+ mutex_init(&rdev->mutex);
+ rdev->reg_data = reg_data;
+ rdev->owner = regulator_desc->owner;
+ rdev->desc = regulator_desc;
+ INIT_LIST_HEAD(&rdev->consumer_list);
+ INIT_LIST_HEAD(&rdev->supply_list);
+ INIT_LIST_HEAD(&rdev->list);
+ INIT_LIST_HEAD(&rdev->slist);
+ BLOCKING_INIT_NOTIFIER_HEAD(&rdev->notifier);
+
+ rdev->dev.class = ®ulator_class;
+ device_initialize(&rdev->dev);
+ snprintf(rdev->dev.bus_id, sizeof(rdev->dev.bus_id),
+ "regulator_%ld_%s",
+ (unsigned long)atomic_inc_return(®ulator_no) - 1,
+ regulator_desc->name);
+
+ ret = device_add(&rdev->dev);
+ if (ret == 0)
+ list_add(&rdev->list, ®ulator_list);
+ else {
+ kfree(rdev);
+ rdev = ERR_PTR(ret);
+ }
+ mutex_unlock(®ulator_list_mutex);
+ return rdev;
+}
+EXPORT_SYMBOL_GPL(regulator_register);
+
+/**
+ * regulator_unregister - unregister regulator
+ * @regulator: regulator source
+ *
+ * Called by regulator drivers to unregister a regulator.
+ */
+void regulator_unregister(struct regulator_dev *rdev)
+{
+ if (rdev == NULL)
+ return;
+
+ mutex_lock(®ulator_list_mutex);
+ list_del(&rdev->list);
+ if (rdev->supply)
+ sysfs_remove_link(&rdev->dev.kobj, "supply");
+ device_unregister(&rdev->dev);
+ mutex_unlock(®ulator_list_mutex);
+}
+EXPORT_SYMBOL_GPL(regulator_unregister);
+
+/**
+ * regulator_set_supply - set regulator supply regulator
+ * @regulator: regulator name
+ * @supply: supply regulator name
+ *
+ * Called by platform initialisation code to set the supply regulator for this
+ * regulator. This ensures that a regulators supply will also be enabled by the
+ * core if it's child is enabled.
+ */
+int regulator_set_supply(const char *regulator, const char *supply)
+{
+ struct regulator_dev *rdev, *supply_rdev;
+ int err;
+
+ if (regulator == NULL || supply == NULL)
+ return -EINVAL;
+
+ mutex_lock(®ulator_list_mutex);
+
+ list_for_each_entry(rdev, ®ulator_list, list) {
+ if (!strcmp(rdev->desc->name, regulator))
+ goto found_regulator;
+ }
+ mutex_unlock(®ulator_list_mutex);
+ return -ENODEV;
+
+found_regulator:
+ list_for_each_entry(supply_rdev, ®ulator_list, list) {
+ if (!strcmp(supply_rdev->desc->name, supply))
+ goto found_supply;
+ }
+ mutex_unlock(®ulator_list_mutex);
+ return -ENODEV;
+
+found_supply:
+ err = sysfs_create_link(&rdev->dev.kobj, &supply_rdev->dev.kobj,
+ "supply");
+ if (err) {
+ printk(KERN_ERR
+ "%s: could not add device link %s err %d\n",
+ __func__, supply_rdev->dev.kobj.name, err);
+ goto out;
+ }
+ rdev->supply = supply_rdev;
+ list_add(&rdev->slist, &supply_rdev->supply_list);
+out:
+ mutex_unlock(®ulator_list_mutex);
+ return err;
+}
+EXPORT_SYMBOL_GPL(regulator_set_supply);
+
+/**
+ * regulator_get_supply - get regulator supply regulator
+ * @regulator: regulator name
+ *
+ * Returns the supply supply regulator name or NULL if no supply regulator
+ * exists (i.e the regulator is supplied directly from USB, Line, Battery, etc)
+ */
+const char *regulator_get_supply(const char *regulator)
+{
+ struct regulator_dev *rdev;
+
+ if (regulator == NULL)
+ return NULL;
+
+ mutex_lock(®ulator_list_mutex);
+ list_for_each_entry(rdev, ®ulator_list, list) {
+ if (!strcmp(rdev->desc->name, regulator))
+ goto found;
+ }
+ mutex_unlock(®ulator_list_mutex);
+ return NULL;
+
+found:
+ mutex_unlock(®ulator_list_mutex);
+ if (rdev->supply)
+ return rdev->supply->desc->name;
+ else
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(regulator_get_supply);
+
+/**
+ * regulator_set_machine_constraints - sets regulator constraints
+ * @regulator: regulator source
+ *
+ * Allows platform initialisation code to define and constrain
+ * regulator circuits e.g. valid voltage/current ranges, etc. NOTE:
+ * Constraints *must* be set by platform code in order for some
+ * regulator operations to proceed i.e. set_voltage, set_current_limit,
+ * set_mode.
+ */
+int regulator_set_machine_constraints(const char *regulator_name,
+ struct regulation_constraints *constraints)
+{
+ struct regulator_dev *rdev;
+ int ret = 0;
+
+ if (regulator_name == NULL)
+ return -EINVAL;
+
+ mutex_lock(®ulator_list_mutex);
+
+ list_for_each_entry(rdev, ®ulator_list, list) {
+ if (!strcmp(regulator_name, rdev->desc->name))
+ goto found;
+ }
+ ret = -ENODEV;
+ goto out;
+
+found:
+ mutex_lock(&rdev->mutex);
+ rdev->constraints = constraints;
+
+ /* do we need to apply the constraint voltage */
+ if (rdev->constraints->apply_uV &&
+ rdev->constraints->min_uV == rdev->constraints->max_uV &&
+ rdev->desc->ops->set_voltage) {
+ ret = rdev->desc->ops->set_voltage(rdev,
+ rdev->constraints->min_uV, rdev->constraints->max_uV);
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to apply %duV"
+ " constraint\n", __func__,
+ rdev->constraints->min_uV);
+ rdev->constraints = NULL;
+ goto out;
+ }
+ }
+
+ /* are we enabled at boot time by firmware / bootloader */
+ if (rdev->constraints->boot_on)
+ rdev->use_count = 1;
+
+ /* do we need to setup our suspend state */
+ if (constraints->initial_state)
+ ret = suspend_prepare(rdev, constraints->initial_state);
+
+ print_constraints(rdev);
+ mutex_unlock(&rdev->mutex);
+
+out:
+ mutex_unlock(®ulator_list_mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_machine_constraints);
+
+
+/**
+ * regulator_set_device_supply: Bind a regulator to a symbolic supply
+ * @regulator: regulator source
+ * @dev: device the supply applies to
+ * @supply: symbolic name for supply
+ *
+ * Allows platform initialisation code to map physical regulator
+ * sources to symbolic names for supplies for use by devices. Devices
+ * should use these symbolic names to request regulators, avoiding the
+ * need to provide board-specific regulator names as platform data.
+ */
+int regulator_set_device_supply(const char *regulator, struct device *dev,
+ const char *supply)
+{
+ struct regulator_map *node;
+
+ if (regulator == NULL || supply == NULL)
+ return -EINVAL;
+
+ node = kmalloc(sizeof(struct regulator_map), GFP_KERNEL);
+ if (node == NULL)
+ return -ENOMEM;
+
+ node->regulator = regulator;
+ node->dev = dev;
+ node->supply = supply;
+
+ mutex_lock(®ulator_list_mutex);
+ list_add(&node->list, ®ulator_map_list);
+ mutex_unlock(®ulator_list_mutex);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(regulator_set_device_supply);
+
+/**
+ * regulator_suspend_prepare: prepare regulators for system wide suspend
+ * @state: system suspend state
+ *
+ * Configure each regulator with it's suspend operating parameters for state.
+ * This will usually be called by machine suspend code prior to supending.
+ */
+int regulator_suspend_prepare(suspend_state_t state)
+{
+ struct regulator_dev *rdev;
+ int ret = 0;
+
+ /* ON is handled by regulator active state */
+ if (state == PM_SUSPEND_ON)
+ return -EINVAL;
+
+ mutex_lock(®ulator_list_mutex);
+ list_for_each_entry(rdev, ®ulator_list, list) {
+
+ mutex_lock(&rdev->mutex);
+ ret = suspend_prepare(rdev, state);
+ mutex_unlock(&rdev->mutex);
+
+ if (ret < 0) {
+ printk(KERN_ERR "%s: failed to prepare %s\n",
+ __func__, rdev->desc->name);
+ goto out;
+ }
+ }
+out:
+ mutex_unlock(®ulator_list_mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_suspend_prepare);
+
+/**
+ * rdev_get_drvdata - get rdev regulator driver data
+ * @regulator: regulator
+ *
+ * Get rdev regulator driver private data. This call can be used in the
+ * regulator driver context.
+ */
+void *rdev_get_drvdata(struct regulator_dev *rdev)
+{
+ return rdev->reg_data;
+}
+EXPORT_SYMBOL_GPL(rdev_get_drvdata);
+
+/**
+ * regulator_get_drvdata - get regulator driver data
+ * @regulator: regulator
+ *
+ * Get regulator driver private data. This call can be used in the consumer
+ * driver context when non API regulator specific functions need to be called.
+ */
+void *regulator_get_drvdata(struct regulator *regulator)
+{
+ return regulator->rdev->reg_data;
+}
+EXPORT_SYMBOL_GPL(regulator_get_drvdata);
+
+/**
+ * regulator_set_drvdata - set regulator driver data
+ * @regulator: regulator
+ * @data: data
+ */
+void regulator_set_drvdata(struct regulator *regulator, void *data)
+{
+ regulator->rdev->reg_data = data;
+}
+EXPORT_SYMBOL_GPL(regulator_set_drvdata);
+
+/**
+ * regulator_get_id - get regulator ID
+ * @regulator: regulator
+ */
+int rdev_get_id(struct regulator_dev *rdev)
+{
+ return rdev->desc->id;
+}
+EXPORT_SYMBOL_GPL(rdev_get_id);
+
+static int __init regulator_init(void)
+{
+ printk(KERN_INFO "regulator: core version %s\n", REGULATOR_VERSION);
+ return class_register(®ulator_class);
+}
+
+/* init early to allow our consumers to complete system booting */
+core_initcall(regulator_init);
--- /dev/null
+/*
+ * fixed.c
+ *
+ * Copyright 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This is useful for systems with mixed controllable and
+ * non-controllable regulators, as well as for allowing testing on
+ * systems with no controllable regulators.
+ */
+
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/fixed.h>
+
+struct fixed_voltage_data {
+ struct regulator_desc desc;
+ struct regulator_dev *dev;
+ int microvolts;
+};
+
+static int fixed_voltage_is_enabled(struct regulator_dev *dev)
+{
+ return 1;
+}
+
+static int fixed_voltage_enable(struct regulator_dev *dev)
+{
+ return 0;
+}
+
+static int fixed_voltage_get_voltage(struct regulator_dev *dev)
+{
+ struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+ return data->microvolts;
+}
+
+static struct regulator_ops fixed_voltage_ops = {
+ .is_enabled = fixed_voltage_is_enabled,
+ .enable = fixed_voltage_enable,
+ .get_voltage = fixed_voltage_get_voltage,
+};
+
+static int regulator_fixed_voltage_probe(struct platform_device *pdev)
+{
+ struct fixed_voltage_config *config = pdev->dev.platform_data;
+ struct fixed_voltage_data *drvdata;
+ int ret;
+
+ drvdata = kzalloc(sizeof(struct fixed_voltage_data), GFP_KERNEL);
+ if (drvdata == NULL) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ drvdata->desc.name = kstrdup(config->supply_name, GFP_KERNEL);
+ if (drvdata->desc.name == NULL) {
+ ret = -ENOMEM;
+ goto err;
+ }
+ drvdata->desc.type = REGULATOR_VOLTAGE;
+ drvdata->desc.owner = THIS_MODULE;
+ drvdata->desc.ops = &fixed_voltage_ops,
+
+ drvdata->microvolts = config->microvolts;
+
+ drvdata->dev = regulator_register(&drvdata->desc, drvdata);
+ if (IS_ERR(drvdata->dev)) {
+ ret = PTR_ERR(drvdata->dev);
+ goto err_name;
+ }
+
+ platform_set_drvdata(pdev, drvdata);
+
+ dev_dbg(&pdev->dev, "%s supplying %duV\n", drvdata->desc.name,
+ drvdata->microvolts);
+
+ return 0;
+
+err_name:
+ kfree(drvdata->desc.name);
+err:
+ kfree(drvdata);
+ return ret;
+}
+
+static int regulator_fixed_voltage_remove(struct platform_device *pdev)
+{
+ struct fixed_voltage_data *drvdata = platform_get_drvdata(pdev);
+
+ regulator_unregister(drvdata->dev);
+ kfree(drvdata->desc.name);
+ kfree(drvdata);
+
+ return 0;
+}
+
+static struct platform_driver regulator_fixed_voltage_driver = {
+ .probe = regulator_fixed_voltage_probe,
+ .remove = regulator_fixed_voltage_remove,
+ .driver = {
+ .name = "reg-fixed-voltage",
+ },
+};
+
+static int __init regulator_fixed_voltage_init(void)
+{
+ return platform_driver_register(®ulator_fixed_voltage_driver);
+}
+module_init(regulator_fixed_voltage_init);
+
+static void __exit regulator_fixed_voltage_exit(void)
+{
+ platform_driver_unregister(®ulator_fixed_voltage_driver);
+}
+module_exit(regulator_fixed_voltage_exit);
+
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_DESCRIPTION("Fixed voltage regulator");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * reg-virtual-consumer.c
+ *
+ * Copyright 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+struct virtual_consumer_data {
+ struct mutex lock;
+ struct regulator *regulator;
+ int enabled;
+ int min_uV;
+ int max_uV;
+ int min_uA;
+ int max_uA;
+ unsigned int mode;
+};
+
+static void update_voltage_constraints(struct virtual_consumer_data *data)
+{
+ int ret;
+
+ if (data->min_uV && data->max_uV
+ && data->min_uV <= data->max_uV) {
+ ret = regulator_set_voltage(data->regulator,
+ data->min_uV, data->max_uV);
+ if (ret != 0) {
+ printk(KERN_ERR "regulator_set_voltage() failed: %d\n",
+ ret);
+ return;
+ }
+ }
+
+ if (data->min_uV && data->max_uV && !data->enabled) {
+ ret = regulator_enable(data->regulator);
+ if (ret == 0)
+ data->enabled = 1;
+ else
+ printk(KERN_ERR "regulator_enable() failed: %d\n",
+ ret);
+ }
+
+ if (!(data->min_uV && data->max_uV) && data->enabled) {
+ ret = regulator_disable(data->regulator);
+ if (ret == 0)
+ data->enabled = 0;
+ else
+ printk(KERN_ERR "regulator_disable() failed: %d\n",
+ ret);
+ }
+}
+
+static void update_current_limit_constraints(struct virtual_consumer_data
+ *data)
+{
+ int ret;
+
+ if (data->max_uA
+ && data->min_uA <= data->max_uA) {
+ ret = regulator_set_current_limit(data->regulator,
+ data->min_uA, data->max_uA);
+ if (ret != 0) {
+ pr_err("regulator_set_current_limit() failed: %d\n",
+ ret);
+ return;
+ }
+ }
+
+ if (data->max_uA && !data->enabled) {
+ ret = regulator_enable(data->regulator);
+ if (ret == 0)
+ data->enabled = 1;
+ else
+ printk(KERN_ERR "regulator_enable() failed: %d\n",
+ ret);
+ }
+
+ if (!(data->min_uA && data->max_uA) && data->enabled) {
+ ret = regulator_disable(data->regulator);
+ if (ret == 0)
+ data->enabled = 0;
+ else
+ printk(KERN_ERR "regulator_disable() failed: %d\n",
+ ret);
+ }
+}
+
+static ssize_t show_min_uV(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ return sprintf(buf, "%d\n", data->min_uV);
+}
+
+static ssize_t set_min_uV(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ long val;
+
+ if (strict_strtol(buf, 10, &val) != 0)
+ return count;
+
+ mutex_lock(&data->lock);
+
+ data->min_uV = val;
+ update_voltage_constraints(data);
+
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_max_uV(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ return sprintf(buf, "%d\n", data->max_uV);
+}
+
+static ssize_t set_max_uV(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ long val;
+
+ if (strict_strtol(buf, 10, &val) != 0)
+ return count;
+
+ mutex_lock(&data->lock);
+
+ data->max_uV = val;
+ update_voltage_constraints(data);
+
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_min_uA(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ return sprintf(buf, "%d\n", data->min_uA);
+}
+
+static ssize_t set_min_uA(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ long val;
+
+ if (strict_strtol(buf, 10, &val) != 0)
+ return count;
+
+ mutex_lock(&data->lock);
+
+ data->min_uA = val;
+ update_current_limit_constraints(data);
+
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_max_uA(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ return sprintf(buf, "%d\n", data->max_uA);
+}
+
+static ssize_t set_max_uA(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ long val;
+
+ if (strict_strtol(buf, 10, &val) != 0)
+ return count;
+
+ mutex_lock(&data->lock);
+
+ data->max_uA = val;
+ update_current_limit_constraints(data);
+
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t show_mode(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+
+ switch (data->mode) {
+ case REGULATOR_MODE_FAST:
+ return sprintf(buf, "fast\n");
+ case REGULATOR_MODE_NORMAL:
+ return sprintf(buf, "normal\n");
+ case REGULATOR_MODE_IDLE:
+ return sprintf(buf, "idle\n");
+ case REGULATOR_MODE_STANDBY:
+ return sprintf(buf, "standby\n");
+ default:
+ return sprintf(buf, "unknown\n");
+ }
+}
+
+static ssize_t set_mode(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct virtual_consumer_data *data = dev_get_drvdata(dev);
+ unsigned int mode;
+ int ret;
+
+ if (strncmp(buf, "fast", strlen("fast")) == 0)
+ mode = REGULATOR_MODE_FAST;
+ else if (strncmp(buf, "normal", strlen("normal")) == 0)
+ mode = REGULATOR_MODE_NORMAL;
+ else if (strncmp(buf, "idle", strlen("idle")) == 0)
+ mode = REGULATOR_MODE_IDLE;
+ else if (strncmp(buf, "standby", strlen("standby")) == 0)
+ mode = REGULATOR_MODE_STANDBY;
+ else {
+ dev_err(dev, "Configuring invalid mode\n");
+ return count;
+ }
+
+ mutex_lock(&data->lock);
+ ret = regulator_set_mode(data->regulator, mode);
+ if (ret == 0)
+ data->mode = mode;
+ else
+ dev_err(dev, "Failed to configure mode: %d\n", ret);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static DEVICE_ATTR(min_microvolts, 0666, show_min_uV, set_min_uV);
+static DEVICE_ATTR(max_microvolts, 0666, show_max_uV, set_max_uV);
+static DEVICE_ATTR(min_microamps, 0666, show_min_uA, set_min_uA);
+static DEVICE_ATTR(max_microamps, 0666, show_max_uA, set_max_uA);
+static DEVICE_ATTR(mode, 0666, show_mode, set_mode);
+
+struct device_attribute *attributes[] = {
+ &dev_attr_min_microvolts,
+ &dev_attr_max_microvolts,
+ &dev_attr_min_microamps,
+ &dev_attr_max_microamps,
+ &dev_attr_mode,
+};
+
+static int regulator_virtual_consumer_probe(struct platform_device *pdev)
+{
+ char *reg_id = pdev->dev.platform_data;
+ struct virtual_consumer_data *drvdata;
+ int ret, i;
+
+ drvdata = kzalloc(sizeof(struct virtual_consumer_data), GFP_KERNEL);
+ if (drvdata == NULL) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ mutex_init(&drvdata->lock);
+
+ drvdata->regulator = regulator_get(&pdev->dev, reg_id);
+ if (IS_ERR(drvdata->regulator)) {
+ ret = PTR_ERR(drvdata->regulator);
+ goto err;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(attributes); i++) {
+ ret = device_create_file(&pdev->dev, attributes[i]);
+ if (ret != 0)
+ goto err;
+ }
+
+ drvdata->mode = regulator_get_mode(drvdata->regulator);
+
+ platform_set_drvdata(pdev, drvdata);
+
+ return 0;
+
+err:
+ for (i = 0; i < ARRAY_SIZE(attributes); i++)
+ device_remove_file(&pdev->dev, attributes[i]);
+ kfree(drvdata);
+ return ret;
+}
+
+static int regulator_virtual_consumer_remove(struct platform_device *pdev)
+{
+ struct virtual_consumer_data *drvdata = platform_get_drvdata(pdev);
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(attributes); i++)
+ device_remove_file(&pdev->dev, attributes[i]);
+ if (drvdata->enabled)
+ regulator_disable(drvdata->regulator);
+ regulator_put(drvdata->regulator);
+
+ kfree(drvdata);
+
+ return 0;
+}
+
+static struct platform_driver regulator_virtual_consumer_driver = {
+ .probe = regulator_virtual_consumer_probe,
+ .remove = regulator_virtual_consumer_remove,
+ .driver = {
+ .name = "reg-virt-consumer",
+ },
+};
+
+
+static int __init regulator_virtual_consumer_init(void)
+{
+ return platform_driver_register(®ulator_virtual_consumer_driver);
+}
+module_init(regulator_virtual_consumer_init);
+
+static void __exit regulator_virtual_consumer_exit(void)
+{
+ platform_driver_unregister(®ulator_virtual_consumer_driver);
+}
+module_exit(regulator_virtual_consumer_exit);
+
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_DESCRIPTION("Virtual regulator consumer");
+MODULE_LICENSE("GPL");
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
if (!rtc->ops)
err = -ENODEV;
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
if (!rtc->ops)
err = -ENODEV;
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
if (!rtc->ops)
err = -ENODEV;
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
if (rtc->ops == NULL)
err = -ENODEV;
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
if (!rtc->ops)
err = -ENODEV;
#include <linux/completion.h>
#include <asm/uaccess.h>
-#include <asm/arch/at91_rtc.h>
+#include <mach/at91_rtc.h>
#define AT91_RTC_FREQ 1
#include <linux/interrupt.h>
#include <linux/ioctl.h>
-#include <asm/arch/board.h>
-#include <asm/arch/at91_rtt.h>
+#include <mach/board.h>
+#include <mach/at91_rtt.h>
/*
* Blackfin On-Chip Real Time Clock Driver
* Supports BF52[257]/BF53[123]/BF53[467]/BF54[24789]
*
- * Copyright 2004-2007 Analog Devices Inc.
+ * Copyright 2004-2008 Analog Devices Inc.
*
* Enter bugs at http://blackfin.uclinux.org/
*
* writes to clear status registers complete immediately.
*/
+/* It may seem odd that there is no SWCNT code in here (which would be exposed
+ * via the periodic interrupt event, or PIE). Since the Blackfin RTC peripheral
+ * runs in units of seconds (N/HZ) but the Linux framework runs in units of HZ
+ * (2^N HZ), there is no point in keeping code that only provides 1 HZ PIEs.
+ * The same exact behavior can be accomplished by using the update interrupt
+ * event (UIE). Maybe down the line the RTC peripheral will suck less in which
+ * case we can re-introduce PIE support.
+ */
+
#include <linux/bcd.h>
#include <linux/completion.h>
#include <linux/delay.h>
* Initialize the RTC. Enable pre-scaler to scale RTC clock
* to 1Hz and clear interrupt/status registers.
*/
-static void bfin_rtc_reset(struct device *dev)
+static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl)
{
struct bfin_rtc *rtc = dev_get_drvdata(dev);
dev_dbg_stamp(dev);
bfin_rtc_sync_pending(dev);
bfin_write_RTC_PREN(0x1);
- bfin_write_RTC_ICTL(RTC_ISTAT_WRITE_COMPLETE);
- bfin_write_RTC_SWCNT(0);
+ bfin_write_RTC_ICTL(rtc_ictl);
bfin_write_RTC_ALARM(0);
bfin_write_RTC_ISTAT(0xFFFF);
rtc->rtc_wrote_regs = 0;
}
}
- if (rtc_ictl & RTC_ISTAT_STOPWATCH) {
- if (rtc_istat & RTC_ISTAT_STOPWATCH) {
- bfin_write_RTC_ISTAT(RTC_ISTAT_STOPWATCH);
- events |= RTC_PF | RTC_IRQF;
- bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
- }
- }
-
if (rtc_ictl & RTC_ISTAT_SEC) {
if (rtc_istat & RTC_ISTAT_SEC) {
bfin_write_RTC_ISTAT(RTC_ISTAT_SEC);
ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, IRQF_SHARED, to_platform_device(dev)->name, dev);
if (!ret)
- bfin_rtc_reset(dev);
+ bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE);
return ret;
}
static void bfin_rtc_release(struct device *dev)
{
dev_dbg_stamp(dev);
- bfin_rtc_reset(dev);
+ bfin_rtc_reset(dev, 0);
free_irq(IRQ_RTC, dev);
}
-static void bfin_rtc_int_set(struct bfin_rtc *rtc, u16 rtc_int)
+static void bfin_rtc_int_set(u16 rtc_int)
{
bfin_write_RTC_ISTAT(rtc_int);
bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() | rtc_int);
}
-static void bfin_rtc_int_clear(struct bfin_rtc *rtc, u16 rtc_int)
+static void bfin_rtc_int_clear(u16 rtc_int)
{
bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() & rtc_int);
}
/* Blackfin has different bits for whether the alarm is
* more than 24 hours away.
*/
- bfin_rtc_int_set(rtc, (rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY));
+ bfin_rtc_int_set(rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY);
}
static int bfin_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg)
{
bfin_rtc_sync_pending(dev);
switch (cmd) {
- case RTC_PIE_ON:
- dev_dbg_stamp(dev);
- bfin_rtc_int_set(rtc, RTC_ISTAT_STOPWATCH);
- bfin_write_RTC_SWCNT(rtc->rtc_dev->irq_freq);
- break;
- case RTC_PIE_OFF:
- dev_dbg_stamp(dev);
- bfin_rtc_int_clear(rtc, ~RTC_ISTAT_STOPWATCH);
- break;
-
case RTC_UIE_ON:
dev_dbg_stamp(dev);
- bfin_rtc_int_set(rtc, RTC_ISTAT_SEC);
+ bfin_rtc_int_set(RTC_ISTAT_SEC);
break;
case RTC_UIE_OFF:
dev_dbg_stamp(dev);
- bfin_rtc_int_clear(rtc, ~RTC_ISTAT_SEC);
+ bfin_rtc_int_clear(~RTC_ISTAT_SEC);
break;
case RTC_AIE_ON:
break;
case RTC_AIE_OFF:
dev_dbg_stamp(dev);
- bfin_rtc_int_clear(rtc, ~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
+ bfin_rtc_int_clear(~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY));
break;
default:
seq_printf(seq,
"alarm_IRQ\t: %s\n"
"wkalarm_IRQ\t: %s\n"
- "seconds_IRQ\t: %s\n"
- "periodic_IRQ\t: %s\n",
+ "seconds_IRQ\t: %s\n",
yesno(ictl & RTC_ISTAT_ALARM),
yesno(ictl & RTC_ISTAT_ALARM_DAY),
- yesno(ictl & RTC_ISTAT_SEC),
- yesno(ictl & RTC_ISTAT_STOPWATCH));
+ yesno(ictl & RTC_ISTAT_SEC));
return 0;
#undef yesno
}
-/**
- * bfin_irq_set_freq - make sure hardware supports requested freq
- * @dev: pointer to RTC device structure
- * @freq: requested frequency rate
- *
- * The Blackfin RTC can only generate periodic events at 1 per
- * second (1 Hz), so reject any attempt at changing it.
- */
-static int bfin_irq_set_freq(struct device *dev, int freq)
-{
- dev_dbg_stamp(dev);
- return -ENOTTY;
-}
-
static struct rtc_class_ops bfin_rtc_ops = {
.open = bfin_rtc_open,
.release = bfin_rtc_release,
.read_alarm = bfin_rtc_read_alarm,
.set_alarm = bfin_rtc_set_alarm,
.proc = bfin_rtc_proc,
- .irq_set_freq = bfin_irq_set_freq,
};
static int __devinit bfin_rtc_probe(struct platform_device *pdev)
ret = PTR_ERR(rtc->rtc_dev);
goto err;
}
- rtc->rtc_dev->irq_freq = 1;
+
+ /* see comment at top of file about stopwatch/PIE */
+ bfin_write_RTC_SWCNT(0);
platform_set_drvdata(pdev, rtc);
+ device_init_wakeup(&pdev->dev, 1);
+
return 0;
err:
return 0;
}
+#ifdef CONFIG_PM
+static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ if (device_may_wakeup(&pdev->dev)) {
+ enable_irq_wake(IRQ_RTC);
+ bfin_rtc_sync_pending(&pdev->dev);
+ } else
+ bfin_rtc_int_clear(-1);
+
+ return 0;
+}
+
+static int bfin_rtc_resume(struct platform_device *pdev)
+{
+ if (device_may_wakeup(&pdev->dev))
+ disable_irq_wake(IRQ_RTC);
+ else
+ bfin_write_RTC_ISTAT(-1);
+
+ return 0;
+}
+#else
+# define bfin_rtc_suspend NULL
+# define bfin_rtc_resume NULL
+#endif
+
static struct platform_driver bfin_rtc_driver = {
.driver = {
.name = "rtc-bfin",
},
.probe = bfin_rtc_probe,
.remove = __devexit_p(bfin_rtc_remove),
+ .suspend = bfin_rtc_suspend,
+ .resume = bfin_rtc_resume,
};
static int __init bfin_rtc_init(void)
err = mutex_lock_interruptible(&rtc->ops_lock);
if (err)
- return -EBUSY;
+ return err;
/* check that the calling task has appropriate permissions
* for certain ioctls. doing this check here is useful
#ifdef CONFIG_RTC_INTF_DEV_UIE_EMUL
clear_uie(rtc);
#endif
+ rtc_irq_set_state(rtc, NULL, 0);
+
if (rtc->ops->release)
rtc->ops->release(rtc->dev.parent);
#include <linux/module.h>
#include <linux/rtc.h>
#include <linux/platform_device.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define EP93XX_RTC_REG(x) (EP93XX_RTC_BASE + (x))
#define EP93XX_RTC_DATA EP93XX_RTC_REG(0x0000)
#include <linux/clk.h>
#include <linux/log2.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <linux/pm.h>
#include <linux/bitops.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
#ifdef CONFIG_ARCH_PXA
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#endif
#define TIMER_FREQ CLOCK_TICK_RATE
else
search_unit_addr = uid->base_unit_addr;
list_for_each_entry(pos, &lcu->grouplist, group) {
- if (pos->uid.base_unit_addr == search_unit_addr)
+ if (pos->uid.base_unit_addr == search_unit_addr &&
+ !strncmp(pos->uid.vduit, uid->vduit, sizeof(uid->vduit)))
return pos;
};
return NULL;
group->uid.base_unit_addr = uid->real_unit_addr;
else
group->uid.base_unit_addr = uid->base_unit_addr;
+ memcpy(group->uid.vduit, uid->vduit, sizeof(uid->vduit));
INIT_LIST_HEAD(&group->group);
INIT_LIST_HEAD(&group->baselist);
INIT_LIST_HEAD(&group->aliaslist);
static DEVICE_ATTR(vendor, 0444, dasd_vendor_show, NULL);
#define UID_STRLEN ( /* vendor */ 3 + 1 + /* serial */ 14 + 1 +\
- /* SSID */ 4 + 1 + /* unit addr */ 2 + 1)
+ /* SSID */ 4 + 1 + /* unit addr */ 2 + 1 +\
+ /* vduit */ 32 + 1)
static ssize_t
dasd_uid_show(struct device *dev, struct device_attribute *attr, char *buf)
sprintf(ua_string, "%02x", uid->real_unit_addr);
break;
}
- snprintf(uid_string, sizeof(uid_string), "%s.%s.%04x.%s",
- uid->vendor, uid->serial, uid->ssid, ua_string);
+ if (strlen(uid->vduit) > 0)
+ snprintf(uid_string, sizeof(uid_string),
+ "%s.%s.%04x.%s.%s",
+ uid->vendor, uid->serial,
+ uid->ssid, ua_string,
+ uid->vduit);
+ else
+ snprintf(uid_string, sizeof(uid_string),
+ "%s.%s.%04x.%s",
+ uid->vendor, uid->serial,
+ uid->ssid, ua_string);
spin_unlock(&dasd_devmap_lock);
return snprintf(buf, PAGE_SIZE, "%s\n", uid_string);
}
memset(pfxdata, 0, sizeof(*pfxdata));
/* prefix data */
pfxdata->format = 0;
- pfxdata->base_address = basepriv->conf_data.ned1.unit_addr;
- pfxdata->base_lss = basepriv->conf_data.ned1.ID;
+ pfxdata->base_address = basepriv->ned->unit_addr;
+ pfxdata->base_lss = basepriv->ned->ID;
pfxdata->validity.define_extend = 1;
/* private uid is kept up to date, conf_data may be outdated */
/*
* Generate device unique id that specifies the physical device.
*/
-static int
-dasd_eckd_generate_uid(struct dasd_device *device, struct dasd_uid *uid)
+static int dasd_eckd_generate_uid(struct dasd_device *device,
+ struct dasd_uid *uid)
{
struct dasd_eckd_private *private;
- struct dasd_eckd_confdata *confdata;
+ int count;
private = (struct dasd_eckd_private *) device->private;
if (!private)
return -ENODEV;
- confdata = &private->conf_data;
- if (!confdata)
+ if (!private->ned || !private->gneq)
return -ENODEV;
memset(uid, 0, sizeof(struct dasd_uid));
- memcpy(uid->vendor, confdata->ned1.HDA_manufacturer,
+ memcpy(uid->vendor, private->ned->HDA_manufacturer,
sizeof(uid->vendor) - 1);
EBCASC(uid->vendor, sizeof(uid->vendor) - 1);
- memcpy(uid->serial, confdata->ned1.HDA_location,
+ memcpy(uid->serial, private->ned->HDA_location,
sizeof(uid->serial) - 1);
EBCASC(uid->serial, sizeof(uid->serial) - 1);
- uid->ssid = confdata->neq.subsystemID;
- uid->real_unit_addr = confdata->ned1.unit_addr;
- if (confdata->ned2.sneq.flags == 0x40 &&
- confdata->ned2.sneq.format == 0x0001) {
- uid->type = confdata->ned2.sneq.sua_flags;
+ uid->ssid = private->gneq->subsystemID;
+ uid->real_unit_addr = private->ned->unit_addr;;
+ if (private->sneq) {
+ uid->type = private->sneq->sua_flags;
if (uid->type == UA_BASE_PAV_ALIAS)
- uid->base_unit_addr = confdata->ned2.sneq.base_unit_addr;
+ uid->base_unit_addr = private->sneq->base_unit_addr;
} else {
uid->type = UA_BASE_DEVICE;
}
+ if (private->vdsneq) {
+ for (count = 0; count < 16; count++) {
+ sprintf(uid->vduit+2*count, "%02x",
+ private->vdsneq->uit[count]);
+ }
+ }
return 0;
}
ret = -ENOMEM;
goto out_error;
}
+
+ /*
+ * buffer has to start with EBCDIC "V1.0" to show
+ * support for virtual device SNEQ
+ */
+ rcd_buf[0] = 0xE5;
+ rcd_buf[1] = 0xF1;
+ rcd_buf[2] = 0x4B;
+ rcd_buf[3] = 0xF0;
cqr = dasd_eckd_build_rcd_lpm(device, rcd_buf, ciw, lpm);
if (IS_ERR(cqr)) {
ret = PTR_ERR(cqr);
return ret;
}
-static int
-dasd_eckd_read_conf(struct dasd_device *device)
+static int dasd_eckd_identify_conf_parts(struct dasd_eckd_private *private)
+{
+
+ struct dasd_sneq *sneq;
+ int i, count;
+
+ private->ned = NULL;
+ private->sneq = NULL;
+ private->vdsneq = NULL;
+ private->gneq = NULL;
+ count = private->conf_len / sizeof(struct dasd_sneq);
+ sneq = (struct dasd_sneq *)private->conf_data;
+ for (i = 0; i < count; ++i) {
+ if (sneq->flags.identifier == 1 && sneq->format == 1)
+ private->sneq = sneq;
+ else if (sneq->flags.identifier == 1 && sneq->format == 4)
+ private->vdsneq = (struct vd_sneq *)sneq;
+ else if (sneq->flags.identifier == 2)
+ private->gneq = (struct dasd_gneq *)sneq;
+ else if (sneq->flags.identifier == 3 && sneq->res1 == 1)
+ private->ned = (struct dasd_ned *)sneq;
+ sneq++;
+ }
+ if (!private->ned || !private->gneq) {
+ private->ned = NULL;
+ private->sneq = NULL;
+ private->vdsneq = NULL;
+ private->gneq = NULL;
+ return -EINVAL;
+ }
+ return 0;
+
+};
+
+static unsigned char dasd_eckd_path_access(void *conf_data, int conf_len)
+{
+ struct dasd_gneq *gneq;
+ int i, count, found;
+
+ count = conf_len / sizeof(*gneq);
+ gneq = (struct dasd_gneq *)conf_data;
+ found = 0;
+ for (i = 0; i < count; ++i) {
+ if (gneq->flags.identifier == 2) {
+ found = 1;
+ break;
+ }
+ gneq++;
+ }
+ if (found)
+ return ((char *)gneq)[18] & 0x07;
+ else
+ return 0;
+}
+
+static int dasd_eckd_read_conf(struct dasd_device *device)
{
void *conf_data;
int conf_len, conf_data_saved;
path_data->opm = ccw_device_get_path_mask(device->cdev);
lpm = 0x80;
conf_data_saved = 0;
-
/* get configuration data per operational path */
for (lpm = 0x80; lpm; lpm>>= 1) {
if (lpm & path_data->opm){
"data retrieved");
continue; /* no error */
}
- if (conf_len != sizeof(struct dasd_eckd_confdata)) {
- MESSAGE(KERN_WARNING,
- "sizes of configuration data mismatch"
- "%d (read) vs %ld (expected)",
- conf_len,
- sizeof(struct dasd_eckd_confdata));
- kfree(conf_data);
- continue; /* no error */
- }
/* save first valid configuration data */
- if (!conf_data_saved){
- memcpy(&private->conf_data, conf_data,
- sizeof(struct dasd_eckd_confdata));
+ if (!conf_data_saved) {
+ kfree(private->conf_data);
+ private->conf_data = conf_data;
+ private->conf_len = conf_len;
+ if (dasd_eckd_identify_conf_parts(private)) {
+ private->conf_data = NULL;
+ private->conf_len = 0;
+ kfree(conf_data);
+ continue;
+ }
conf_data_saved++;
}
- switch (((char *)conf_data)[242] & 0x07){
+ switch (dasd_eckd_path_access(conf_data, conf_len)) {
case 0x02:
path_data->npm |= lpm;
break;
path_data->ppm |= lpm;
break;
}
- kfree(conf_data);
+ if (conf_data != private->conf_data)
+ kfree(conf_data);
}
}
return 0;
dasd_free_block(device->block);
device->block = NULL;
out_err1:
+ kfree(private->conf_data);
kfree(device->private);
device->private = NULL;
return rc;
static void dasd_eckd_uncheck_device(struct dasd_device *device)
{
+ struct dasd_eckd_private *private;
+
+ private = (struct dasd_eckd_private *) device->private;
dasd_alias_disconnect_device_from_lcu(device);
+ private->ned = NULL;
+ private->sneq = NULL;
+ private->vdsneq = NULL;
+ private->gneq = NULL;
+ private->conf_len = 0;
+ kfree(private->conf_data);
+ private->conf_data = NULL;
}
static struct dasd_ccw_req *
info->characteristics_size = sizeof(struct dasd_eckd_characteristics);
memcpy(info->characteristics, &private->rdc_data,
sizeof(struct dasd_eckd_characteristics));
- info->confdata_size = sizeof(struct dasd_eckd_confdata);
- memcpy(info->configuration_data, &private->conf_data,
- sizeof(struct dasd_eckd_confdata));
+ info->confdata_size = min((unsigned long)private->conf_len,
+ sizeof(info->configuration_data));
+ memcpy(info->configuration_data, private->conf_data,
+ info->confdata_size);
return 0;
}
__u8 reserved3[10];
} __attribute__ ((packed));
-struct dasd_eckd_confdata {
+/* elements of the configuration data */
+struct dasd_ned {
struct {
- struct {
- unsigned char identifier:2;
- unsigned char token_id:1;
- unsigned char sno_valid:1;
- unsigned char subst_sno:1;
- unsigned char recNED:1;
- unsigned char emuNED:1;
- unsigned char reserved:1;
- } __attribute__ ((packed)) flags;
- __u8 descriptor;
- __u8 dev_class;
- __u8 reserved;
- unsigned char dev_type[6];
- unsigned char dev_model[3];
- unsigned char HDA_manufacturer[3];
- unsigned char HDA_location[2];
- unsigned char HDA_seqno[12];
- __u8 ID;
- __u8 unit_addr;
- } __attribute__ ((packed)) ned1;
- union {
- struct {
- struct {
- unsigned char identifier:2;
- unsigned char token_id:1;
- unsigned char sno_valid:1;
- unsigned char subst_sno:1;
- unsigned char recNED:1;
- unsigned char emuNED:1;
- unsigned char reserved:1;
- } __attribute__ ((packed)) flags;
- __u8 descriptor;
- __u8 reserved[2];
- unsigned char dev_type[6];
- unsigned char dev_model[3];
- unsigned char DASD_manufacturer[3];
- unsigned char DASD_location[2];
- unsigned char DASD_seqno[12];
- __u16 ID;
- } __attribute__ ((packed)) ned;
- struct {
- unsigned char flags; /* byte 0 */
- unsigned char res1; /* byte 1 */
- __u16 format; /* byte 2-3 */
- unsigned char res2[4]; /* byte 4-7 */
- unsigned char sua_flags; /* byte 8 */
- __u8 base_unit_addr; /* byte 9 */
- unsigned char res3[22]; /* byte 10-31 */
- } __attribute__ ((packed)) sneq;
- } __attribute__ ((packed)) ned2;
+ __u8 identifier:2;
+ __u8 token_id:1;
+ __u8 sno_valid:1;
+ __u8 subst_sno:1;
+ __u8 recNED:1;
+ __u8 emuNED:1;
+ __u8 reserved:1;
+ } __attribute__ ((packed)) flags;
+ __u8 descriptor;
+ __u8 dev_class;
+ __u8 reserved;
+ __u8 dev_type[6];
+ __u8 dev_model[3];
+ __u8 HDA_manufacturer[3];
+ __u8 HDA_location[2];
+ __u8 HDA_seqno[12];
+ __u8 ID;
+ __u8 unit_addr;
+} __attribute__ ((packed));
+
+struct dasd_sneq {
struct {
- struct {
- unsigned char identifier:2;
- unsigned char token_id:1;
- unsigned char sno_valid:1;
- unsigned char subst_sno:1;
- unsigned char recNED:1;
- unsigned char emuNED:1;
- unsigned char reserved:1;
- } __attribute__ ((packed)) flags;
- __u8 descriptor;
- __u8 reserved[2];
- unsigned char cont_type[6];
- unsigned char cont_model[3];
- unsigned char cont_manufacturer[3];
- unsigned char cont_location[2];
- unsigned char cont_seqno[12];
- __u16 ID;
- } __attribute__ ((packed)) ned3;
+ __u8 identifier:2;
+ __u8 reserved:6;
+ } __attribute__ ((packed)) flags;
+ __u8 res1;
+ __u16 format;
+ __u8 res2[4]; /* byte 4- 7 */
+ __u8 sua_flags; /* byte 8 */
+ __u8 base_unit_addr; /* byte 9 */
+ __u8 res3[22]; /* byte 10-31 */
+} __attribute__ ((packed));
+
+struct vd_sneq {
struct {
- struct {
- unsigned char identifier:2;
- unsigned char token_id:1;
- unsigned char sno_valid:1;
- unsigned char subst_sno:1;
- unsigned char recNED:1;
- unsigned char emuNED:1;
- unsigned char reserved:1;
- } __attribute__ ((packed)) flags;
- __u8 descriptor;
- __u8 reserved[2];
- unsigned char cont_type[6];
- unsigned char empty[3];
- unsigned char cont_manufacturer[3];
- unsigned char cont_location[2];
- unsigned char cont_seqno[12];
- __u16 ID;
- } __attribute__ ((packed)) ned4;
- unsigned char ned5[32];
- unsigned char ned6[32];
- unsigned char ned7[32];
+ __u8 identifier:2;
+ __u8 reserved:6;
+ } __attribute__ ((packed)) flags;
+ __u8 res1;
+ __u16 format;
+ __u8 res2[4]; /* byte 4- 7 */
+ __u8 uit[16]; /* byte 8-23 */
+ __u8 res3[8]; /* byte 24-31 */
+} __attribute__ ((packed));
+
+struct dasd_gneq {
struct {
- struct {
- unsigned char identifier:2;
- unsigned char reserved:6;
- } __attribute__ ((packed)) flags;
- __u8 selector;
- __u16 interfaceID;
- __u32 reserved;
- __u16 subsystemID;
- struct {
- unsigned char sp0:1;
- unsigned char sp1:1;
- unsigned char reserved:5;
- unsigned char scluster:1;
- } __attribute__ ((packed)) spathID;
- __u8 unit_address;
- __u8 dev_ID;
- __u8 dev_address;
- __u8 adapterID;
- __u16 link_address;
- struct {
- unsigned char parallel:1;
- unsigned char escon:1;
- unsigned char reserved:1;
- unsigned char ficon:1;
- unsigned char reserved2:4;
- } __attribute__ ((packed)) protocol_type;
- struct {
- unsigned char PID_in_236:1;
- unsigned char reserved:7;
- } __attribute__ ((packed)) format_flags;
- __u8 log_dev_address;
- unsigned char reserved2[12];
- } __attribute__ ((packed)) neq;
+ __u8 identifier:2;
+ __u8 reserved:6;
+ } __attribute__ ((packed)) flags;
+ __u8 reserved[7];
+ __u16 subsystemID;
+ __u8 reserved2[22];
} __attribute__ ((packed));
struct dasd_eckd_path {
struct dasd_eckd_private {
struct dasd_eckd_characteristics rdc_data;
- struct dasd_eckd_confdata conf_data;
+ u8 *conf_data;
+ int conf_len;
+ /* pointers to specific parts in the conf_data */
+ struct dasd_ned *ned;
+ struct dasd_sneq *sneq;
+ struct vd_sneq *vdsneq;
+ struct dasd_gneq *gneq;
+
struct dasd_eckd_path path_data;
struct eckd_count count_area[5];
int init_cqr_status;
__u16 ssid;
__u8 real_unit_addr;
__u8 base_unit_addr;
+ char vduit[33];
};
/*
void
sclp_sync_wait(void)
{
+ unsigned long long old_tick;
unsigned long flags;
unsigned long cr0, cr0_sync;
u64 timeout;
if (!irq_context)
local_bh_disable();
/* Enable service-signal interruption, disable timer interrupts */
+ old_tick = local_tick_disable();
trace_hardirqs_on();
__ctl_store(cr0, 0, 0);
cr0_sync = cr0;
+ cr0_sync &= 0xffff00a0;
cr0_sync |= 0x00000200;
- cr0_sync &= 0xFFFFF3AC;
__ctl_load(cr0_sync, 0, 0);
__raw_local_irq_stosm(0x01);
/* Loop until driver state indicates finished request */
__ctl_load(cr0, 0, 0);
if (!irq_context)
_local_bh_enable();
+ local_tick_enable(old_tick);
local_irq_restore(flags);
}
-
EXPORT_SYMBOL(sclp_sync_wait);
/* Dispatch changes in send and receive mask to registered listeners. */
sclp_attach_storage(id);
switch (action) {
case MEM_ONLINE:
+ case MEM_GOING_OFFLINE:
+ case MEM_CANCEL_OFFLINE:
break;
case MEM_GOING_ONLINE:
rc = sclp_mem_change_state(start, size, 1);
case MEM_CANCEL_ONLINE:
sclp_mem_change_state(start, size, 0);
break;
+ case MEM_OFFLINE:
+ sclp_mem_change_state(start, size, 0);
+ break;
default:
rc = -EINVAL;
break;
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/cpu.h>
-#include <linux/kthread.h>
#include <linux/sysdev.h>
#include <linux/workqueue.h>
#include <asm/smp.h>
put_online_cpus();
}
-static int sclp_cpu_kthread(void *data)
-{
- smp_rescan_cpus();
- return 0;
-}
-
static void __ref sclp_cpu_change_notify(struct work_struct *work)
{
- /* Can't call smp_rescan_cpus() from workqueue context since it may
- * deadlock in case of cpu hotplug. So we have to create a kernel
- * thread in order to call it.
- */
- kthread_run(sclp_cpu_kthread, NULL, "cpu_rescan");
+ smp_rescan_cpus();
}
static void sclp_conf_receiver_fn(struct evbuf_header *evbuf)
* Author(s): Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
*/
-#include <linux/slab.h>
+#include <linux/vmalloc.h>
#include <linux/bitops.h>
#include "idset.h"
#include "css.h"
{
struct idset *set;
- set = kzalloc(sizeof(struct idset) + bitmap_size(num_ssid, num_id),
- GFP_KERNEL);
+ set = vmalloc(sizeof(struct idset) + bitmap_size(num_ssid, num_id));
if (set) {
set->num_ssid = num_ssid;
set->num_id = num_id;
+ memset(set->bitmap, 0, bitmap_size(num_ssid, num_id));
}
return set;
}
void idset_free(struct idset *set)
{
- kfree(set);
+ vfree(set);
}
void idset_clear(struct idset *set)
goto out_rel;
/* qdr is used in ccw1.cda which is u32 */
- irq_ptr->qdr = kzalloc(sizeof(struct qdr), GFP_KERNEL | GFP_DMA);
+ irq_ptr->qdr = (struct qdr *) get_zeroed_page(GFP_KERNEL | GFP_DMA);
if (!irq_ptr->qdr)
goto out_rel;
WARN_ON((unsigned long)irq_ptr->qdr & 0xfff);
return 0;
}
-void __exit qdio_remove_perf_stats(void)
+void qdio_remove_perf_stats(void)
{
#ifdef CONFIG_PROC_FS
remove_proc_entry("qdio_perf", NULL);
kmem_cache_free(qdio_q_cache, q);
}
}
- kfree(irq_ptr->qdr);
+ free_page((unsigned long) irq_ptr->qdr);
free_page(irq_ptr->chsc_page);
free_page((unsigned long) irq_ptr);
}
return 0;
}
-void __exit qdio_setup_exit(void)
+void qdio_setup_exit(void)
{
kmem_cache_destroy(qdio_q_cache);
}
return len;
}
-void s390_virtio_console_init(void)
+void __init s390_virtio_console_init(void)
{
virtio_cons_early_init(early_put_chars);
}
int next_element_to_fill;
struct sk_buff_head skb_list;
struct list_head ctx_list;
+ int is_header[16];
};
struct qeth_card;
/* exports for qeth discipline device drivers */
extern struct qeth_card_list_struct qeth_core_card_list;
-
+extern struct kmem_cache *qeth_core_header_cache;
extern struct qeth_dbf_info qeth_dbf[QETH_DBF_INFOS];
void qeth_set_allowed_threads(struct qeth_card *, unsigned long , int);
int qeth_get_elements_no(struct qeth_card *, void *, struct sk_buff *, int);
int qeth_do_send_packet_fast(struct qeth_card *, struct qeth_qdio_out_q *,
struct sk_buff *, struct qeth_hdr *, int,
- struct qeth_eddp_context *);
+ struct qeth_eddp_context *, int, int);
int qeth_do_send_packet(struct qeth_card *, struct qeth_qdio_out_q *,
struct sk_buff *, struct qeth_hdr *,
int, struct qeth_eddp_context *);
#include <linux/mii.h>
#include <linux/kthread.h>
-#include <asm-s390/ebcdic.h>
-#include <asm-s390/io.h>
+#include <asm/ebcdic.h>
+#include <asm/io.h>
#include <asm/s390_rdev.h>
#include "qeth_core.h"
struct qeth_card_list_struct qeth_core_card_list;
EXPORT_SYMBOL_GPL(qeth_core_card_list);
+struct kmem_cache *qeth_core_header_cache;
+EXPORT_SYMBOL_GPL(qeth_core_header_cache);
static struct device *qeth_core_root_dev;
static unsigned int known_devices[][10] = QETH_MODELLIST_ARRAY;
}
qeth_eddp_buf_release_contexts(buf);
for (i = 0; i < QETH_MAX_BUFFER_ELEMENTS(queue->card); ++i) {
+ if (buf->buffer->element[i].addr && buf->is_header[i])
+ kmem_cache_free(qeth_core_header_cache,
+ buf->buffer->element[i].addr);
+ buf->is_header[i] = 0;
buf->buffer->element[i].length = 0;
buf->buffer->element[i].addr = NULL;
buf->buffer->element[i].flags = 0;
if (skb_shinfo(skb)->nr_frags > 0)
elements_needed = (skb_shinfo(skb)->nr_frags + 1);
if (elements_needed == 0)
- elements_needed = 1 + (((((unsigned long) hdr) % PAGE_SIZE)
- + skb->len) >> PAGE_SHIFT);
+ elements_needed = 1 + (((((unsigned long) skb->data) %
+ PAGE_SIZE) + skb->len) >> PAGE_SHIFT);
if ((elements_needed + elems) > QETH_MAX_BUFFER_ELEMENTS(card)) {
QETH_DBF_MESSAGE(2, "Invalid size of IP packet "
"(Number=%d / Length=%d). Discarded.\n",
EXPORT_SYMBOL_GPL(qeth_get_elements_no);
static inline void __qeth_fill_buffer(struct sk_buff *skb,
- struct qdio_buffer *buffer, int is_tso, int *next_element_to_fill)
+ struct qdio_buffer *buffer, int is_tso, int *next_element_to_fill,
+ int offset)
{
int length = skb->len;
int length_here;
data = skb->data;
first_lap = (is_tso == 0 ? 1 : 0);
+ if (offset >= 0) {
+ data = skb->data + offset;
+ first_lap = 0;
+ }
+
while (length > 0) {
/* length_here is the remaining amount of data in this page */
length_here = PAGE_SIZE - ((unsigned long) data % PAGE_SIZE);
}
static inline int qeth_fill_buffer(struct qeth_qdio_out_q *queue,
- struct qeth_qdio_out_buffer *buf, struct sk_buff *skb)
+ struct qeth_qdio_out_buffer *buf, struct sk_buff *skb,
+ struct qeth_hdr *hdr, int offset, int hd_len)
{
struct qdio_buffer *buffer;
- struct qeth_hdr_tso *hdr;
int flush_cnt = 0, hdr_len, large_send = 0;
buffer = buf->buffer;
atomic_inc(&skb->users);
skb_queue_tail(&buf->skb_list, skb);
- hdr = (struct qeth_hdr_tso *) skb->data;
/*check first on TSO ....*/
- if (hdr->hdr.hdr.l3.id == QETH_HEADER_TYPE_TSO) {
+ if (hdr->hdr.l3.id == QETH_HEADER_TYPE_TSO) {
int element = buf->next_element_to_fill;
- hdr_len = sizeof(struct qeth_hdr_tso) + hdr->ext.dg_hdr_len;
+ hdr_len = sizeof(struct qeth_hdr_tso) +
+ ((struct qeth_hdr_tso *)hdr)->ext.dg_hdr_len;
/*fill first buffer entry only with header information */
buffer->element[element].addr = skb->data;
buffer->element[element].length = hdr_len;
skb->len -= hdr_len;
large_send = 1;
}
+
+ if (offset >= 0) {
+ int element = buf->next_element_to_fill;
+ buffer->element[element].addr = hdr;
+ buffer->element[element].length = sizeof(struct qeth_hdr) +
+ hd_len;
+ buffer->element[element].flags = SBAL_FLAGS_FIRST_FRAG;
+ buf->is_header[element] = 1;
+ buf->next_element_to_fill++;
+ }
+
if (skb_shinfo(skb)->nr_frags == 0)
__qeth_fill_buffer(skb, buffer, large_send,
- (int *)&buf->next_element_to_fill);
+ (int *)&buf->next_element_to_fill, offset);
else
__qeth_fill_buffer_frag(skb, buffer, large_send,
(int *)&buf->next_element_to_fill);
int qeth_do_send_packet_fast(struct qeth_card *card,
struct qeth_qdio_out_q *queue, struct sk_buff *skb,
struct qeth_hdr *hdr, int elements_needed,
- struct qeth_eddp_context *ctx)
+ struct qeth_eddp_context *ctx, int offset, int hd_len)
{
struct qeth_qdio_out_buffer *buffer;
int buffers_needed = 0;
}
atomic_set(&queue->state, QETH_OUT_Q_UNLOCKED);
if (ctx == NULL) {
- qeth_fill_buffer(queue, buffer, skb);
+ qeth_fill_buffer(queue, buffer, skb, hdr, offset, hd_len);
qeth_flush_buffers(queue, index, 1);
} else {
flush_cnt = qeth_eddp_fill_buffer(queue, ctx, index);
}
}
if (ctx == NULL)
- tmp = qeth_fill_buffer(queue, buffer, skb);
+ tmp = qeth_fill_buffer(queue, buffer, skb, hdr, -1, 0);
else {
tmp = qeth_eddp_fill_buffer(queue, ctx,
queue->next_buf_to_fill);
rc = IS_ERR(qeth_core_root_dev) ? PTR_ERR(qeth_core_root_dev) : 0;
if (rc)
goto register_err;
- return 0;
+ qeth_core_header_cache = kmem_cache_create("qeth_hdr",
+ sizeof(struct qeth_hdr) + ETH_HLEN, 64, 0, NULL);
+ if (!qeth_core_header_cache) {
+ rc = -ENOMEM;
+ goto slab_err;
+ }
+
+ return 0;
+slab_err:
+ s390_root_dev_unregister(qeth_core_root_dev);
register_err:
driver_remove_file(&qeth_core_ccwgroup_driver.driver,
&driver_attr_group);
&driver_attr_group);
ccwgroup_driver_unregister(&qeth_core_ccwgroup_driver);
ccw_driver_unregister(&qeth_ccw_driver);
+ kmem_cache_destroy(qeth_core_header_cache);
qeth_unregister_dbf_views();
PRINT_INFO("core functions removed\n");
}
static void qeth_l2_fill_header(struct qeth_card *card, struct qeth_hdr *hdr,
struct sk_buff *skb, int ipv, int cast_type)
{
- struct vlan_ethhdr *veth = (struct vlan_ethhdr *)((skb->data) +
- QETH_HEADER_SIZE);
+ struct vlan_ethhdr *veth = (struct vlan_ethhdr *)skb_mac_header(skb);
memset(hdr, 0, sizeof(struct qeth_hdr));
hdr->hdr.l2.id = QETH_HEADER_TYPE_LAYER2;
int tx_bytes = skb->len;
enum qeth_large_send_types large_send = QETH_LARGE_SEND_NO;
struct qeth_eddp_context *ctx = NULL;
+ int data_offset = -1;
+ int elements_needed = 0;
+ int hd_len = 0;
if ((card->state != CARD_STATE_UP) || !card->lan_online) {
card->stats.tx_carrier_errors++;
if (card->info.type == QETH_CARD_TYPE_OSN)
hdr = (struct qeth_hdr *)skb->data;
else {
- /* create a clone with writeable headroom */
- new_skb = skb_realloc_headroom(skb, sizeof(struct qeth_hdr));
- if (!new_skb)
- goto tx_drop;
- hdr = (struct qeth_hdr *)skb_push(new_skb,
+ if ((card->info.type == QETH_CARD_TYPE_IQD) && (!large_send) &&
+ (skb_shinfo(skb)->nr_frags == 0)) {
+ new_skb = skb;
+ data_offset = ETH_HLEN;
+ hd_len = ETH_HLEN;
+ hdr = kmem_cache_alloc(qeth_core_header_cache,
+ GFP_ATOMIC);
+ if (!hdr)
+ goto tx_drop;
+ elements_needed++;
+ skb_reset_mac_header(new_skb);
+ qeth_l2_fill_header(card, hdr, new_skb, ipv, cast_type);
+ hdr->hdr.l2.pkt_length = new_skb->len;
+ memcpy(((char *)hdr) + sizeof(struct qeth_hdr),
+ skb_mac_header(new_skb), ETH_HLEN);
+ } else {
+ /* create a clone with writeable headroom */
+ new_skb = skb_realloc_headroom(skb,
+ sizeof(struct qeth_hdr));
+ if (!new_skb)
+ goto tx_drop;
+ hdr = (struct qeth_hdr *)skb_push(new_skb,
sizeof(struct qeth_hdr));
- qeth_l2_fill_header(card, hdr, new_skb, ipv, cast_type);
+ skb_set_mac_header(new_skb, sizeof(struct qeth_hdr));
+ qeth_l2_fill_header(card, hdr, new_skb, ipv, cast_type);
+ }
}
if (large_send == QETH_LARGE_SEND_EDDP) {
goto tx_drop;
}
} else {
- elements = qeth_get_elements_no(card, (void *)hdr, new_skb, 0);
- if (!elements)
+ elements = qeth_get_elements_no(card, (void *)hdr, new_skb,
+ elements_needed);
+ if (!elements) {
+ if (data_offset >= 0)
+ kmem_cache_free(qeth_core_header_cache, hdr);
goto tx_drop;
+ }
}
if ((large_send == QETH_LARGE_SEND_NO) &&
elements, ctx);
else
rc = qeth_do_send_packet_fast(card, queue, new_skb, hdr,
- elements, ctx);
+ elements, ctx, data_offset, hd_len);
if (!rc) {
card->stats.tx_packets++;
card->stats.tx_bytes += tx_bytes;
if (ctx != NULL)
qeth_eddp_put_context(ctx);
+ if (data_offset >= 0)
+ kmem_cache_free(qeth_core_header_cache, hdr);
+
if (rc == -EBUSY) {
if (new_skb != skb)
dev_kfree_skb_any(new_skb);
int tx_bytes = skb->len;
enum qeth_large_send_types large_send = QETH_LARGE_SEND_NO;
struct qeth_eddp_context *ctx = NULL;
+ int data_offset = -1;
if ((card->info.type == QETH_CARD_TYPE_IQD) &&
(skb->protocol != htons(ETH_P_IPV6)) &&
card->perf_stats.outbound_start_time = qeth_get_micros();
}
- /* create a clone with writeable headroom */
- new_skb = skb_realloc_headroom(skb, sizeof(struct qeth_hdr_tso) +
- VLAN_HLEN);
- if (!new_skb)
- goto tx_drop;
+ if (skb_is_gso(skb))
+ large_send = card->options.large_send;
+
+ if ((card->info.type == QETH_CARD_TYPE_IQD) && (!large_send) &&
+ (skb_shinfo(skb)->nr_frags == 0)) {
+ new_skb = skb;
+ data_offset = ETH_HLEN;
+ hdr = kmem_cache_alloc(qeth_core_header_cache, GFP_ATOMIC);
+ if (!hdr)
+ goto tx_drop;
+ elements_needed++;
+ } else {
+ /* create a clone with writeable headroom */
+ new_skb = skb_realloc_headroom(skb, sizeof(struct qeth_hdr_tso)
+ + VLAN_HLEN);
+ if (!new_skb)
+ goto tx_drop;
+ }
if (card->info.type == QETH_CARD_TYPE_IQD) {
- skb_pull(new_skb, ETH_HLEN);
+ if (data_offset < 0)
+ skb_pull(new_skb, ETH_HLEN);
} else {
if (new_skb->protocol == htons(ETH_P_IP)) {
if (card->dev->type == ARPHRD_IEEE802_TR)
netif_stop_queue(dev);
- if (skb_is_gso(new_skb))
- large_send = card->options.large_send;
-
/* fix hardware limitation: as long as we do not have sbal
* chaining we can not send long frag lists so we temporary
* switch to EDDP
qeth_tso_fill_header(card, hdr, new_skb);
elements_needed++;
} else {
- hdr = (struct qeth_hdr *)skb_push(new_skb,
+ if (data_offset < 0) {
+ hdr = (struct qeth_hdr *)skb_push(new_skb,
sizeof(struct qeth_hdr));
- qeth_l3_fill_header(card, hdr, new_skb, ipv, cast_type);
+ qeth_l3_fill_header(card, hdr, new_skb, ipv,
+ cast_type);
+ } else {
+ qeth_l3_fill_header(card, hdr, new_skb, ipv,
+ cast_type);
+ hdr->hdr.l3.length = new_skb->len - data_offset;
+ }
}
if (large_send == QETH_LARGE_SEND_EDDP) {
} else {
int elems = qeth_get_elements_no(card, (void *)hdr, new_skb,
elements_needed);
- if (!elems)
+ if (!elems) {
+ if (data_offset >= 0)
+ kmem_cache_free(qeth_core_header_cache, hdr);
goto tx_drop;
+ }
elements_needed += elems;
}
elements_needed, ctx);
else
rc = qeth_do_send_packet_fast(card, queue, new_skb, hdr,
- elements_needed, ctx);
+ elements_needed, ctx, data_offset, 0);
if (!rc) {
card->stats.tx_packets++;
if (ctx != NULL)
qeth_eddp_put_context(ctx);
+ if (data_offset >= 0)
+ kmem_cache_free(qeth_core_header_cache, hdr);
+
if (rc == -EBUSY) {
if (new_skb != skb)
dev_kfree_skb_any(new_skb);
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#if defined(__APCS_32__)
#define LOADREGS(t,r,l...) ldm##t r, l
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/spinlock.h>
-#include <linux/hdreg.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/div64.h>
{ PCI_VDEVICE(TTI, 0x3522), (kernel_ulong_t)&hptiop_itl_ops },
{ PCI_VDEVICE(TTI, 0x3410), (kernel_ulong_t)&hptiop_itl_ops },
{ PCI_VDEVICE(TTI, 0x3540), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x3530), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x3560), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x4322), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x4210), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x4211), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x4310), (kernel_ulong_t)&hptiop_itl_ops },
+ { PCI_VDEVICE(TTI, 0x4311), (kernel_ulong_t)&hptiop_itl_ops },
{ PCI_VDEVICE(TTI, 0x3120), (kernel_ulong_t)&hptiop_mv_ops },
{ PCI_VDEVICE(TTI, 0x3122), (kernel_ulong_t)&hptiop_mv_ops },
{ PCI_VDEVICE(TTI, 0x3020), (kernel_ulong_t)&hptiop_mv_ops },
mutex_lock(&idescsi_ref_mutex);
scsi = ide_scsi_g(disk);
if (scsi) {
- scsi_host_get(scsi->host);
- if (ide_device_get(scsi->drive)) {
- scsi_host_put(scsi->host);
+ if (ide_device_get(scsi->drive))
scsi = NULL;
- }
+ else
+ scsi_host_get(scsi->host);
}
mutex_unlock(&idescsi_ref_mutex);
return scsi;
static void ide_scsi_put(struct ide_scsi_obj *scsi)
{
+ ide_drive_t *drive = scsi->drive;
+
mutex_lock(&idescsi_ref_mutex);
- ide_device_put(scsi->drive);
scsi_host_put(scsi->host);
+ ide_device_put(drive);
mutex_unlock(&idescsi_ref_mutex);
}
spi_transport_rd_attr(pcomp_en, "%d\n");
spi_transport_rd_attr(hold_mcs, "%d\n");
-/* we only care about the first child device so we return 1 */
+/* we only care about the first child device that's a real SCSI device
+ * so we return 1 to terminate the iteration when we find it */
static int child_iter(struct device *dev, void *data)
{
- struct scsi_device *sdev = to_scsi_device(dev);
+ if (!scsi_is_sdev_device(dev))
+ return 0;
- spi_dv_device(sdev);
+ spi_dv_device(to_scsi_device(dev));
return 1;
}
return 0;
}
-#define VPD_INQUIRY_SIZE 512
+#define VPD_INQUIRY_SIZE 36
static void ses_match_to_enclosure(struct enclosure_device *edev,
struct scsi_device *sdev)
{
unsigned char *buf = kmalloc(VPD_INQUIRY_SIZE, GFP_KERNEL);
unsigned char *desc;
- int len;
+ u16 vpd_len;
struct efd efd = {
.addr = 0,
};
VPD_INQUIRY_SIZE, NULL, SES_TIMEOUT, SES_RETRIES))
goto free;
- len = (buf[2] << 8) + buf[3];
+ vpd_len = (buf[2] << 8) + buf[3];
+ kfree(buf);
+ buf = kmalloc(vpd_len, GFP_KERNEL);
+ if (!buf)
+ return;
+ cmd[3] = vpd_len >> 8;
+ cmd[4] = vpd_len & 0xff;
+ if (scsi_execute_req(sdev, cmd, DMA_FROM_DEVICE, buf,
+ vpd_len, NULL, SES_TIMEOUT, SES_RETRIES))
+ goto free;
+
desc = buf + 4;
- while (desc < buf + len) {
+ while (desc < buf + vpd_len) {
enum scsi_protocol proto = desc[0] >> 4;
u8 code_set = desc[0] & 0x0f;
u8 piv = desc[1] & 0x80;
*/
flush_dcache_page(pages[i]);
/* ?? Is locking needed? I don't think so */
- /* if (TestSetPageLocked(pages[i]))
+ /* if (!trylock_page(pages[i]))
goto out_unlock; */
}
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/hardware/dec21285.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#define BAUD_BASE (mem_fclk_21285/64)
* the interrupt is enabled. Delays are necessary to
* allow register changes to become visible.
*/
- spin_lock(&up->port.lock);
+ spin_lock_irqsave(&up->port.lock, flags);
if (up->port.flags & UPF_SHARE_IRQ)
disable_irq_nosync(up->port.irq);
if (up->port.flags & UPF_SHARE_IRQ)
enable_irq(up->port.irq);
- spin_unlock(&up->port.lock);
+ spin_unlock_irqrestore(&up->port.lock, flags);
/*
* If the interrupt is not reasserted, setup a timer to
obj-$(CONFIG_SERIAL_68360) += 68360serial.o
obj-$(CONFIG_SERIAL_COLDFIRE) += mcfserial.o
obj-$(CONFIG_SERIAL_MCF) += mcf.o
-obj-$(CONFIG_V850E_UART) += v850e_uart.o
obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
obj-$(CONFIG_SERIAL_DZ) += dz.o
#include <asm/io.h>
#include <asm/mach/serial_at91.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#ifdef CONFIG_ARM
-#include <asm/arch/cpu.h>
-#include <asm/arch/gpio.h>
+#include <mach/cpu.h>
+#include <mach/gpio.h>
#endif
#define PDC_BUFFER_SIZE 512
if (line >= port->info->port.tty->driver->num)
return;
- switch (port->info->port.tty->ldisc.num) {
+ switch (port->info->port.tty->termios->c_line) {
case N_IRDA:
val = UART_GET_GCTL(&bfin_serial_ports[line]);
val |= (IREN | RPOLC);
#include <linux/serial_core.h>
#include <linux/serial.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/hardware/clps7111.h>
#define SCC_WAIT_CLOSING 100
+#define GPIO_CTS 0
+#define GPIO_RTS 1
+#define GPIO_DCD 2
+#define GPIO_DSR 3
+#define GPIO_DTR 4
+#define GPIO_RI 5
+
+#define NUM_GPIOS (GPIO_RI+1)
+
struct uart_cpm_port {
struct uart_port port;
u16 rx_nrfifos;
unsigned char *rx_buf;
u32 flags;
void (*set_lineif)(struct uart_cpm_port *);
+ struct clk *clk;
u8 brg;
uint dp_addr;
void *mem_addr;
int wait_closing;
/* value to combine with opcode to form cpm command */
u32 command;
+ int gpios[NUM_GPIOS];
};
extern int cpm_uart_nr;
#include <linux/dma-mapping.h>
#include <linux/fs_uart_pd.h>
#include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/clk.h>
#include <asm/io.h>
#include <asm/irq.h>
static void cpm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- /* Whee. Do nothing. */
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+
+ if (pinfo->gpios[GPIO_RTS] >= 0)
+ gpio_set_value(pinfo->gpios[GPIO_RTS], !(mctrl & TIOCM_RTS));
+
+ if (pinfo->gpios[GPIO_DTR] >= 0)
+ gpio_set_value(pinfo->gpios[GPIO_DTR], !(mctrl & TIOCM_DTR));
}
static unsigned int cpm_uart_get_mctrl(struct uart_port *port)
{
- /* Whee. Do nothing. */
- return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+ struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
+ unsigned int mctrl = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ if (pinfo->gpios[GPIO_CTS] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_CTS]))
+ mctrl &= ~TIOCM_CTS;
+ }
+
+ if (pinfo->gpios[GPIO_DSR] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_DSR]))
+ mctrl &= ~TIOCM_DSR;
+ }
+
+ if (pinfo->gpios[GPIO_DCD] >= 0) {
+ if (gpio_get_value(pinfo->gpios[GPIO_DCD]))
+ mctrl &= ~TIOCM_CAR;
+ }
+
+ if (pinfo->gpios[GPIO_RI] >= 0) {
+ if (!gpio_get_value(pinfo->gpios[GPIO_RI]))
+ mctrl |= TIOCM_RNG;
+ }
+
+ return mctrl;
}
/*
out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
}
- cpm_set_brg(pinfo->brg - 1, baud);
+ if (pinfo->clk)
+ clk_set_rate(pinfo->clk, baud);
+ else
+ cpm_set_brg(pinfo->brg - 1, baud);
spin_unlock_irqrestore(&port->lock, flags);
}
void __iomem *mem, *pram;
int len;
int ret;
+ int i;
- data = of_get_property(np, "fsl,cpm-brg", &len);
- if (!data || len != 4) {
- printk(KERN_ERR "CPM UART %s has no/invalid "
- "fsl,cpm-brg property.\n", np->name);
- return -EINVAL;
+ data = of_get_property(np, "clock", NULL);
+ if (data) {
+ struct clk *clk = clk_get(NULL, (const char*)data);
+ if (!IS_ERR(clk))
+ pinfo->clk = clk;
+ }
+ if (!pinfo->clk) {
+ data = of_get_property(np, "fsl,cpm-brg", &len);
+ if (!data || len != 4) {
+ printk(KERN_ERR "CPM UART %s has no/invalid "
+ "fsl,cpm-brg property.\n", np->name);
+ return -EINVAL;
+ }
+ pinfo->brg = *data;
}
- pinfo->brg = *data;
data = of_get_property(np, "fsl,cpm-command", &len);
if (!data || len != 4) {
goto out_pram;
}
+ for (i = 0; i < NUM_GPIOS; i++)
+ pinfo->gpios[i] = of_get_gpio(np, i);
+
return cpm_uart_request_port(&pinfo->port);
out_pram:
static struct e100_serial rs_table[] = {
{ .baud = DEF_BAUD,
- .port = (unsigned char *)R_SERIAL0_CTRL,
+ .ioport = (unsigned char *)R_SERIAL0_CTRL,
.irq = 1U << 12, /* uses DMA 6 and 7 */
.oclrintradr = R_DMA_CH6_CLR_INTR,
.ofirstadr = R_DMA_CH6_FIRST,
}, /* ttyS0 */
#ifndef CONFIG_SVINTO_SIM
{ .baud = DEF_BAUD,
- .port = (unsigned char *)R_SERIAL1_CTRL,
+ .ioport = (unsigned char *)R_SERIAL1_CTRL,
.irq = 1U << 16, /* uses DMA 8 and 9 */
.oclrintradr = R_DMA_CH8_CLR_INTR,
.ofirstadr = R_DMA_CH8_FIRST,
}, /* ttyS1 */
{ .baud = DEF_BAUD,
- .port = (unsigned char *)R_SERIAL2_CTRL,
+ .ioport = (unsigned char *)R_SERIAL2_CTRL,
.irq = 1U << 4, /* uses DMA 2 and 3 */
.oclrintradr = R_DMA_CH2_CLR_INTR,
.ofirstadr = R_DMA_CH2_FIRST,
}, /* ttyS2 */
{ .baud = DEF_BAUD,
- .port = (unsigned char *)R_SERIAL3_CTRL,
+ .ioport = (unsigned char *)R_SERIAL3_CTRL,
.irq = 1U << 8, /* uses DMA 4 and 5 */
.oclrintradr = R_DMA_CH4_CLR_INTR,
.ofirstadr = R_DMA_CH4_FIRST,
/* Output */
#define E100_RTS_GET(info) ((info)->rx_ctrl & E100_RTS_MASK)
/* Input */
-#define E100_CTS_GET(info) ((info)->port[REG_STATUS] & E100_CTS_MASK)
+#define E100_CTS_GET(info) ((info)->ioport[REG_STATUS] & E100_CTS_MASK)
/* These are typically PA or PB and 0 means 0V, 1 means 3.3V */
/* Is an output */
local_irq_save(flags);
info->rx_ctrl &= ~E100_RTS_MASK;
info->rx_ctrl |= (set ? 0 : E100_RTS_MASK); /* RTS is active low */
- info->port[REG_REC_CTRL] = info->rx_ctrl;
+ info->ioport[REG_REC_CTRL] = info->rx_ctrl;
local_irq_restore(flags);
#ifdef SERIAL_DEBUG_IO
printk("ser%i rts %i\n", info->line, set);
{
#ifndef CONFIG_SVINTO_SIM
/* disable the receiver */
- info->port[REG_REC_CTRL] =
+ info->ioport[REG_REC_CTRL] =
(info->rx_ctrl &= ~IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
#endif
}
{
#ifndef CONFIG_SVINTO_SIM
/* enable the receiver */
- info->port[REG_REC_CTRL] =
+ info->ioport[REG_REC_CTRL] =
(info->rx_ctrl |= IO_MASK(R_SERIAL0_REC_CTRL, rec_enable));
#endif
}
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
}
- *((unsigned long *)&info->port[REG_XOFF]) = xoff;
+ *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
local_irq_restore(flags);
}
}
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
}
- *((unsigned long *)&info->port[REG_XOFF]) = xoff;
+ *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
if (!info->uses_dma_out &&
info->xmit.head != info->xmit.tail && info->xmit.buf)
e100_enable_serial_tx_ready_irq(info);
handle_all_descr_data(info);
/* Read the status register to detect errors */
- rstat = info->port[REG_STATUS];
+ rstat = info->ioport[REG_STATUS];
if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
DFLOW(DEBUG_LOG(info->line, "XOFF detect stat %x\n", rstat));
}
/* If we got an error, we must reset it by reading the
* data_in field
*/
- unsigned char data = info->port[REG_DATA];
+ unsigned char data = info->ioport[REG_DATA];
PROCSTAT(ser_stat[info->line].errors_cnt++);
DEBUG_LOG(info->line, "#dERR: s d 0x%04X\n",
/* We check data_avail bit to determine if data has
* arrived since last time
*/
- unsigned char rstat = info->port[REG_STATUS];
+ unsigned char rstat = info->ioport[REG_STATUS];
/* error or datavail? */
if (rstat & SER_ERROR_MASK) {
TIMERD(DEBUG_LOG(info->line, "timeout: rstat 0x%03X\n",
rstat | (info->line << 8)));
/* Read data to clear status flags */
- (void)info->port[REG_DATA];
+ (void)info->ioport[REG_DATA];
info->forced_eop = 0;
START_FLUSH_FAST_TIMER(info, "magic");
}
/* Read data and status at the same time */
- data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]);
+ data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
more_data:
if (data_read & IO_MASK(R_SERIAL0_READ, xoff_detect) ) {
DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
info->icount.rx++;
- data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]);
+ data_read = *((unsigned long *)&info->ioport[REG_DATA_STATUS32]);
if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) {
DEBUG_LOG(info->line, "ser_rx %c in loop\n", IO_EXTRACT(R_SERIAL0_READ, data_in, data_read));
goto more_data;
return handle_ser_rx_interrupt_no_dma(info);
}
/* DMA is used */
- rstat = info->port[REG_STATUS];
+ rstat = info->ioport[REG_STATUS];
if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) ) {
DFLOW(DEBUG_LOG(info->line, "XOFF detect\n", 0));
}
/* If we got an error, we must reset it by reading the
* data_in field
*/
- data = info->port[REG_DATA];
+ data = info->ioport[REG_DATA];
DINTR1(DEBUG_LOG(info->line, "ser_rx! %c\n", data));
DINTR1(DEBUG_LOG(info->line, "ser_rx err stat %02X\n", rstat));
if (!data && (rstat & SER_FRAMING_ERR_MASK)) {
unsigned char rstat;
DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char));
local_irq_save(flags);
- rstat = info->port[REG_STATUS];
+ rstat = info->ioport[REG_STATUS];
DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
- info->port[REG_TR_DATA] = info->x_char;
+ info->ioport[REG_TR_DATA] = info->x_char;
info->icount.tx++;
info->x_char = 0;
/* We must enable since it is disabled in ser_interrupt */
/* We only use normal tx interrupt when sending x_char */
DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0));
local_irq_save(flags);
- rstat = info->port[REG_STATUS];
+ rstat = info->ioport[REG_STATUS];
DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat));
e100_disable_serial_tx_ready_irq(info);
if (info->port.tty->stopped)
DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail]));
/* Send a byte, rs485 timing is critical so turn of ints */
local_irq_save(flags);
- info->port[REG_TR_DATA] = info->xmit.buf[info->xmit.tail];
+ info->ioport[REG_TR_DATA] = info->xmit.buf[info->xmit.tail];
info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1);
info->icount.tx++;
if (info->xmit.head == info->xmit.tail) {
/* dummy read to reset any serial errors */
- (void)info->port[REG_DATA];
+ (void)info->ioport[REG_DATA];
/* enable the interrupts */
if (info->uses_dma_out)
/* shut down the transmitter and receiver */
DFLOW(DEBUG_LOG(info->line, "shutdown %i\n", info->line));
e100_disable_rx(info);
- info->port[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40);
+ info->ioport[REG_TR_CTRL] = (info->tx_ctrl &= ~0x40);
/* disable interrupts, reset dma channels */
if (info->uses_dma_in) {
if (!info->port.tty || !info->port.tty->termios)
return;
- if (!info->port)
+ if (!info->ioport)
return;
cflag = info->port.tty->termios->c_cflag;
info->baud = cflag_to_baud(cflag);
#ifndef CONFIG_SVINTO_SIM
- info->port[REG_BAUD] = cflag_to_etrax_baud(cflag);
+ info->ioport[REG_BAUD] = cflag_to_etrax_baud(cflag);
#endif /* CONFIG_SVINTO_SIM */
}
/* actually write the control regs to the hardware */
- info->port[REG_TR_CTRL] = info->tx_ctrl;
- info->port[REG_REC_CTRL] = info->rx_ctrl;
+ info->ioport[REG_TR_CTRL] = info->tx_ctrl;
+ info->ioport[REG_REC_CTRL] = info->rx_ctrl;
xoff = IO_FIELD(R_SERIAL0_XOFF, xoff_char, STOP_CHAR(info->port.tty));
xoff |= IO_STATE(R_SERIAL0_XOFF, tx_stop, enable);
if (info->port.tty->termios->c_iflag & IXON ) {
xoff |= IO_STATE(R_SERIAL0_XOFF, auto_xoff, enable);
}
- *((unsigned long *)&info->port[REG_XOFF]) = xoff;
+ *((unsigned long *)&info->ioport[REG_XOFF]) = xoff;
local_irq_restore(flags);
#endif /* !CONFIG_SVINTO_SIM */
#ifdef SERIAL_DEBUG_DATA
if (info->line == SERIAL_DEBUG_LINE)
printk("rs_raw_write (%d), status %d\n",
- count, info->port[REG_STATUS]);
+ count, info->ioport[REG_STATUS]);
#endif
#ifdef CONFIG_SVINTO_SIM
memset(&tmp, 0, sizeof(tmp));
tmp.type = info->type;
tmp.line = info->line;
- tmp.port = (int)info->port;
+ tmp.port = (int)info->ioport;
tmp.irq = info->irq;
tmp.flags = info->flags;
tmp.baud_base = info->baud_base;
}
#endif
-static void
+static int
rs_break(struct tty_struct *tty, int break_state)
{
struct e100_serial *info = (struct e100_serial *)tty->driver_data;
unsigned long flags;
- if (!info->port)
- return;
+ if (!info->ioport)
+ return -EIO;
local_irq_save(flags);
if (break_state == -1) {
/* Set bit 7 (txd) and 6 (tr_enable) */
info->tx_ctrl |= (0x80 | 0x40);
}
- info->port[REG_TR_CTRL] = info->tx_ctrl;
+ info->ioport[REG_TR_CTRL] = info->tx_ctrl;
local_irq_restore(flags);
+ return 0;
}
static int
unsigned long tmp;
ret = sprintf(buf, "%d: uart:E100 port:%lX irq:%d",
- info->line, (unsigned long)info->port, info->irq);
+ info->line, (unsigned long)info->ioport, info->irq);
- if (!info->port || (info->type == PORT_UNKNOWN)) {
+ if (!info->ioport || (info->type == PORT_UNKNOWN)) {
ret += sprintf(buf+ret, "\n");
return ret;
}
}
{
- unsigned char rstat = info->port[REG_STATUS];
+ unsigned char rstat = info->ioport[REG_STATUS];
if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) )
ret += sprintf(buf+ret, " xoff_detect:1");
}
if (info->enabled) {
printk(KERN_INFO "%s%d at 0x%x is a builtin UART with DMA\n",
- serial_driver->name, info->line, (unsigned int)info->port);
+ serial_driver->name, info->line, (unsigned int)info->ioport);
}
}
#ifdef CONFIG_ETRAX_FAST_TIMER
};
struct e100_serial {
+ struct tty_port port;
int baud;
- volatile u8 *port; /* R_SERIALx_CTRL */
+ volatile u8 *ioport; /* R_SERIALx_CTRL */
u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */
/* Output registers */
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/arch/imx-uart.h>
+#include <mach/hardware.h>
+#include <mach/imx-uart.h>
/* Register definitions */
#define URXD0 0x0 /* Receiver Register */
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
-#include <asm/arch/netx-regs.h>
+#include <mach/hardware.h>
+#include <mach/netx-regs.h>
/* We've been assigned a range on the "Low-density serial ports" major */
#define SERIAL_NX_MAJOR 204
#include <linux/clk.h>
#include <asm/io.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/irq.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
struct uart_pxa_port {
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include "samsung.h"
#include <linux/serial.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include "samsung.h"
#include <linux/serial.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include "samsung.h"
#include <linux/serial.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include "samsung.h"
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach/serial_sa1100.h>
/* We've been assigned a range on the "Low-density serial ports" major */
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include "samsung.h"
#include <asm/irq.h>
#include <asm/mach/irq.h>
-#include <asm/arch/regs-uart.h>
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-uart.h>
+#include <mach/regs-irq.h>
#if defined(CONFIG_SERIAL_KS8695_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
SCIx_FNS(SCxRDR, 0x0a, 8, 0x14, 8, 0x0A, 8, 0x14, 8, 0x05, 8)
SCIF_FNS(SCFCR, 0x0c, 8, 0x18, 16)
#if defined(CONFIG_CPU_SUBTYPE_SH7760) || \
- defined(CONFIG_CPU_SUBTYPE_SH7763) || \
defined(CONFIG_CPU_SUBTYPE_SH7780) || \
defined(CONFIG_CPU_SUBTYPE_SH7785)
+SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16)
SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16)
SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16)
SCIF_FNS(SCSPTR, 0, 0, 0x24, 16)
SCIF_FNS(SCLSR, 0, 0, 0x28, 16)
-#if defined(CONFIG_CPU_SUBTYPE_SH7763)
-/* SH7763 SCIF2 */
+#elif defined(CONFIG_CPU_SUBTYPE_SH7763)
SCIF_FNS(SCFDR, 0, 0, 0x1C, 16)
SCIF_FNS(SCSPTR2, 0, 0, 0x20, 16)
-SCIF_FNS(SCLSR2, 0, 0, 0x24, 16)
-#endif /* CONFIG_CPU_SUBTYPE_SH7763 */
+SCIF_FNS(SCLSR2, 0, 0, 0x24, 16)
+SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16)
+SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16)
+SCIF_FNS(SCSPTR, 0, 0, 0x24, 16)
+SCIF_FNS(SCLSR, 0, 0, 0x28, 16)
#else
SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16)
#if defined(CONFIG_CPU_SUBTYPE_SH7722)
+++ /dev/null
-/*
- * drivers/serial/v850e_uart.c -- Serial I/O using V850E on-chip UART or UARTB
- *
- * Copyright (C) 2001,02,03 NEC Electronics Corporation
- * Copyright (C) 2001,02,03 Miles Bader <miles@gnu.org>
- *
- * This file is subject to the terms and conditions of the GNU General
- * Public License. See the file COPYING in the main directory of this
- * archive for more details.
- *
- * Written by Miles Bader <miles@gnu.org>
- */
-
-/* This driver supports both the original V850E UART interface (called
- merely `UART' in the docs) and the newer `UARTB' interface, which is
- roughly a superset of the first one. The selection is made at
- configure time -- if CONFIG_V850E_UARTB is defined, then UARTB is
- presumed, otherwise the old UART -- as these are on-CPU UARTS, a system
- can never have both.
-
- The UARTB interface also has a 16-entry FIFO mode, which is not
- yet supported by this driver. */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/console.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-
-#include <asm/v850e_uart.h>
-
-/* Initial UART state. This may be overridden by machine-dependent headers. */
-#ifndef V850E_UART_INIT_BAUD
-#define V850E_UART_INIT_BAUD 115200
-#endif
-#ifndef V850E_UART_INIT_CFLAGS
-#define V850E_UART_INIT_CFLAGS (B115200 | CS8 | CREAD)
-#endif
-
-/* A string used for prefixing printed descriptions; since the same UART
- macro is actually used on other chips than the V850E. This must be a
- constant string. */
-#ifndef V850E_UART_CHIP_NAME
-#define V850E_UART_CHIP_NAME "V850E"
-#endif
-
-#define V850E_UART_MINOR_BASE 64 /* First tty minor number */
-
-\f
-/* Low-level UART functions. */
-
-/* Configure and turn on uart channel CHAN, using the termios `control
- modes' bits in CFLAGS, and a baud-rate of BAUD. */
-void v850e_uart_configure (unsigned chan, unsigned cflags, unsigned baud)
-{
- int flags;
- v850e_uart_speed_t old_speed;
- v850e_uart_config_t old_config;
- v850e_uart_speed_t new_speed = v850e_uart_calc_speed (baud);
- v850e_uart_config_t new_config = v850e_uart_calc_config (cflags);
-
- /* Disable interrupts while we're twiddling the hardware. */
- local_irq_save (flags);
-
-#ifdef V850E_UART_PRE_CONFIGURE
- V850E_UART_PRE_CONFIGURE (chan, cflags, baud);
-#endif
-
- old_config = V850E_UART_CONFIG (chan);
- old_speed = v850e_uart_speed (chan);
-
- if (! v850e_uart_speed_eq (old_speed, new_speed)) {
- /* The baud rate has changed. First, disable the UART. */
- V850E_UART_CONFIG (chan) = V850E_UART_CONFIG_FINI;
- old_config = 0; /* Force the uart to be re-initialized. */
-
- /* Reprogram the baud-rate generator. */
- v850e_uart_set_speed (chan, new_speed);
- }
-
- if (! (old_config & V850E_UART_CONFIG_ENABLED)) {
- /* If we are using the uart for the first time, start by
- enabling it, which must be done before turning on any
- other bits. */
- V850E_UART_CONFIG (chan) = V850E_UART_CONFIG_INIT;
- /* See the initial state. */
- old_config = V850E_UART_CONFIG (chan);
- }
-
- if (new_config != old_config) {
- /* Which of the TXE/RXE bits we'll temporarily turn off
- before changing other control bits. */
- unsigned temp_disable = 0;
- /* Which of the TXE/RXE bits will be enabled. */
- unsigned enable = 0;
- unsigned changed_bits = new_config ^ old_config;
-
- /* Which of RX/TX will be enabled in the new configuration. */
- if (new_config & V850E_UART_CONFIG_RX_BITS)
- enable |= (new_config & V850E_UART_CONFIG_RX_ENABLE);
- if (new_config & V850E_UART_CONFIG_TX_BITS)
- enable |= (new_config & V850E_UART_CONFIG_TX_ENABLE);
-
- /* Figure out which of RX/TX needs to be disabled; note
- that this will only happen if they're not already
- disabled. */
- if (changed_bits & V850E_UART_CONFIG_RX_BITS)
- temp_disable
- |= (old_config & V850E_UART_CONFIG_RX_ENABLE);
- if (changed_bits & V850E_UART_CONFIG_TX_BITS)
- temp_disable
- |= (old_config & V850E_UART_CONFIG_TX_ENABLE);
-
- /* We have to turn off RX and/or TX mode before changing
- any associated control bits. */
- if (temp_disable)
- V850E_UART_CONFIG (chan) = old_config & ~temp_disable;
-
- /* Write the new control bits, while RX/TX are disabled. */
- if (changed_bits & ~enable)
- V850E_UART_CONFIG (chan) = new_config & ~enable;
-
- v850e_uart_config_delay (new_config, new_speed);
-
- /* Write the final version, with enable bits turned on. */
- V850E_UART_CONFIG (chan) = new_config;
- }
-
- local_irq_restore (flags);
-}
-
-\f
-/* Low-level console. */
-
-#ifdef CONFIG_V850E_UART_CONSOLE
-
-static void v850e_uart_cons_write (struct console *co,
- const char *s, unsigned count)
-{
- if (count > 0) {
- unsigned chan = co->index;
- unsigned irq = V850E_UART_TX_IRQ (chan);
- int irq_was_enabled, irq_was_pending, flags;
-
- /* We don't want to get `transmission completed'
- interrupts, since we're busy-waiting, so we disable them
- while sending (we don't disable interrupts entirely
- because sending over a serial line is really slow). We
- save the status of the tx interrupt and restore it when
- we're done so that using printk doesn't interfere with
- normal serial transmission (other than interleaving the
- output, of course!). This should work correctly even if
- this function is interrupted and the interrupt printks
- something. */
-
- /* Disable interrupts while fiddling with tx interrupt. */
- local_irq_save (flags);
- /* Get current tx interrupt status. */
- irq_was_enabled = v850e_intc_irq_enabled (irq);
- irq_was_pending = v850e_intc_irq_pending (irq);
- /* Disable tx interrupt if necessary. */
- if (irq_was_enabled)
- v850e_intc_disable_irq (irq);
- /* Turn interrupts back on. */
- local_irq_restore (flags);
-
- /* Send characters. */
- while (count > 0) {
- int ch = *s++;
-
- if (ch == '\n') {
- /* We don't have the benefit of a tty
- driver, so translate NL into CR LF. */
- v850e_uart_wait_for_xmit_ok (chan);
- v850e_uart_putc (chan, '\r');
- }
-
- v850e_uart_wait_for_xmit_ok (chan);
- v850e_uart_putc (chan, ch);
-
- count--;
- }
-
- /* Restore saved tx interrupt status. */
- if (irq_was_enabled) {
- /* Wait for the last character we sent to be
- completely transmitted (as we'll get an
- interrupt interrupt at that point). */
- v850e_uart_wait_for_xmit_done (chan);
- /* Clear pending interrupts received due
- to our transmission, unless there was already
- one pending, in which case we want the
- handler to be called. */
- if (! irq_was_pending)
- v850e_intc_clear_pending_irq (irq);
- /* ... and then turn back on handling. */
- v850e_intc_enable_irq (irq);
- }
- }
-}
-
-extern struct uart_driver v850e_uart_driver;
-static struct console v850e_uart_cons =
-{
- .name = "ttyS",
- .write = v850e_uart_cons_write,
- .device = uart_console_device,
- .flags = CON_PRINTBUFFER,
- .cflag = V850E_UART_INIT_CFLAGS,
- .index = -1,
- .data = &v850e_uart_driver,
-};
-
-void v850e_uart_cons_init (unsigned chan)
-{
- v850e_uart_configure (chan, V850E_UART_INIT_CFLAGS,
- V850E_UART_INIT_BAUD);
- v850e_uart_cons.index = chan;
- register_console (&v850e_uart_cons);
- printk ("Console: %s on-chip UART channel %d\n",
- V850E_UART_CHIP_NAME, chan);
-}
-
-/* This is what the init code actually calls. */
-static int v850e_uart_console_init (void)
-{
- v850e_uart_cons_init (V850E_UART_CONSOLE_CHANNEL);
- return 0;
-}
-console_initcall(v850e_uart_console_init);
-
-#define V850E_UART_CONSOLE &v850e_uart_cons
-
-#else /* !CONFIG_V850E_UART_CONSOLE */
-#define V850E_UART_CONSOLE 0
-#endif /* CONFIG_V850E_UART_CONSOLE */
-\f
-/* TX/RX interrupt handlers. */
-
-static void v850e_uart_stop_tx (struct uart_port *port);
-
-void v850e_uart_tx (struct uart_port *port)
-{
- struct circ_buf *xmit = &port->info->xmit;
- int stopped = uart_tx_stopped (port);
-
- if (v850e_uart_xmit_ok (port->line)) {
- int tx_ch;
-
- if (port->x_char) {
- tx_ch = port->x_char;
- port->x_char = 0;
- } else if (!uart_circ_empty (xmit) && !stopped) {
- tx_ch = xmit->buf[xmit->tail];
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- } else
- goto no_xmit;
-
- v850e_uart_putc (port->line, tx_ch);
- port->icount.tx++;
-
- if (uart_circ_chars_pending (xmit) < WAKEUP_CHARS)
- uart_write_wakeup (port);
- }
-
- no_xmit:
- if (uart_circ_empty (xmit) || stopped)
- v850e_uart_stop_tx (port, stopped);
-}
-
-static irqreturn_t v850e_uart_tx_irq(int irq, void *data)
-{
- struct uart_port *port = data;
- v850e_uart_tx (port);
- return IRQ_HANDLED;
-}
-
-static irqreturn_t v850e_uart_rx_irq(int irq, void *data)
-{
- struct uart_port *port = data;
- unsigned ch_stat = TTY_NORMAL;
- unsigned ch = v850e_uart_getc (port->line);
- unsigned err = v850e_uart_err (port->line);
-
- if (err) {
- if (err & V850E_UART_ERR_OVERRUN) {
- ch_stat = TTY_OVERRUN;
- port->icount.overrun++;
- } else if (err & V850E_UART_ERR_FRAME) {
- ch_stat = TTY_FRAME;
- port->icount.frame++;
- } else if (err & V850E_UART_ERR_PARITY) {
- ch_stat = TTY_PARITY;
- port->icount.parity++;
- }
- }
-
- port->icount.rx++;
-
- tty_insert_flip_char (port->info->port.tty, ch, ch_stat);
- tty_schedule_flip (port->info->port.tty);
-
- return IRQ_HANDLED;
-}
-
-\f
-/* Control functions for the serial framework. */
-
-static void v850e_uart_nop (struct uart_port *port) { }
-static int v850e_uart_success (struct uart_port *port) { return 0; }
-
-static unsigned v850e_uart_tx_empty (struct uart_port *port)
-{
- return TIOCSER_TEMT; /* Can't detect. */
-}
-
-static void v850e_uart_set_mctrl (struct uart_port *port, unsigned mctrl)
-{
-#ifdef V850E_UART_SET_RTS
- V850E_UART_SET_RTS (port->line, (mctrl & TIOCM_RTS));
-#endif
-}
-
-static unsigned v850e_uart_get_mctrl (struct uart_port *port)
-{
- /* We don't support DCD or DSR, so consider them permanently active. */
- int mctrl = TIOCM_CAR | TIOCM_DSR;
-
- /* We may support CTS. */
-#ifdef V850E_UART_CTS
- mctrl |= V850E_UART_CTS(port->line) ? TIOCM_CTS : 0;
-#else
- mctrl |= TIOCM_CTS;
-#endif
-
- return mctrl;
-}
-
-static void v850e_uart_start_tx (struct uart_port *port)
-{
- v850e_intc_disable_irq (V850E_UART_TX_IRQ (port->line));
- v850e_uart_tx (port);
- v850e_intc_enable_irq (V850E_UART_TX_IRQ (port->line));
-}
-
-static void v850e_uart_stop_tx (struct uart_port *port)
-{
- v850e_intc_disable_irq (V850E_UART_TX_IRQ (port->line));
-}
-
-static void v850e_uart_start_rx (struct uart_port *port)
-{
- v850e_intc_enable_irq (V850E_UART_RX_IRQ (port->line));
-}
-
-static void v850e_uart_stop_rx (struct uart_port *port)
-{
- v850e_intc_disable_irq (V850E_UART_RX_IRQ (port->line));
-}
-
-static void v850e_uart_break_ctl (struct uart_port *port, int break_ctl)
-{
- /* Umm, do this later. */
-}
-
-static int v850e_uart_startup (struct uart_port *port)
-{
- int err;
-
- /* Alloc RX irq. */
- err = request_irq (V850E_UART_RX_IRQ (port->line), v850e_uart_rx_irq,
- IRQF_DISABLED, "v850e_uart", port);
- if (err)
- return err;
-
- /* Alloc TX irq. */
- err = request_irq (V850E_UART_TX_IRQ (port->line), v850e_uart_tx_irq,
- IRQF_DISABLED, "v850e_uart", port);
- if (err) {
- free_irq (V850E_UART_RX_IRQ (port->line), port);
- return err;
- }
-
- v850e_uart_start_rx (port);
-
- return 0;
-}
-
-static void v850e_uart_shutdown (struct uart_port *port)
-{
- /* Disable port interrupts. */
- free_irq (V850E_UART_TX_IRQ (port->line), port);
- free_irq (V850E_UART_RX_IRQ (port->line), port);
-
- /* Turn off xmit/recv enable bits. */
- V850E_UART_CONFIG (port->line)
- &= ~(V850E_UART_CONFIG_TX_ENABLE
- | V850E_UART_CONFIG_RX_ENABLE);
- /* Then reset the channel. */
- V850E_UART_CONFIG (port->line) = 0;
-}
-
-static void
-v850e_uart_set_termios (struct uart_port *port, struct ktermios *termios,
- struct ktermios *old)
-{
- unsigned cflags = termios->c_cflag;
-
- /* Restrict flags to legal values. */
- if ((cflags & CSIZE) != CS7 && (cflags & CSIZE) != CS8)
- /* The new value of CSIZE is invalid, use the old value. */
- cflags = (cflags & ~CSIZE)
- | (old ? (old->c_cflag & CSIZE) : CS8);
-
- termios->c_cflag = cflags;
-
- v850e_uart_configure (port->line, cflags,
- uart_get_baud_rate (port, termios, old,
- v850e_uart_min_baud(),
- v850e_uart_max_baud()));
-}
-
-static const char *v850e_uart_type (struct uart_port *port)
-{
- return port->type == PORT_V850E_UART ? "v850e_uart" : 0;
-}
-
-static void v850e_uart_config_port (struct uart_port *port, int flags)
-{
- if (flags & UART_CONFIG_TYPE)
- port->type = PORT_V850E_UART;
-}
-
-static int
-v850e_uart_verify_port (struct uart_port *port, struct serial_struct *ser)
-{
- if (ser->type != PORT_UNKNOWN && ser->type != PORT_V850E_UART)
- return -EINVAL;
- if (ser->irq != V850E_UART_TX_IRQ (port->line))
- return -EINVAL;
- return 0;
-}
-
-static struct uart_ops v850e_uart_ops = {
- .tx_empty = v850e_uart_tx_empty,
- .get_mctrl = v850e_uart_get_mctrl,
- .set_mctrl = v850e_uart_set_mctrl,
- .start_tx = v850e_uart_start_tx,
- .stop_tx = v850e_uart_stop_tx,
- .stop_rx = v850e_uart_stop_rx,
- .enable_ms = v850e_uart_nop,
- .break_ctl = v850e_uart_break_ctl,
- .startup = v850e_uart_startup,
- .shutdown = v850e_uart_shutdown,
- .set_termios = v850e_uart_set_termios,
- .type = v850e_uart_type,
- .release_port = v850e_uart_nop,
- .request_port = v850e_uart_success,
- .config_port = v850e_uart_config_port,
- .verify_port = v850e_uart_verify_port,
-};
-\f
-/* Initialization and cleanup. */
-
-static struct uart_driver v850e_uart_driver = {
- .owner = THIS_MODULE,
- .driver_name = "v850e_uart",
- .dev_name = "ttyS",
- .major = TTY_MAJOR,
- .minor = V850E_UART_MINOR_BASE,
- .nr = V850E_UART_NUM_CHANNELS,
- .cons = V850E_UART_CONSOLE,
-};
-
-
-static struct uart_port v850e_uart_ports[V850E_UART_NUM_CHANNELS];
-
-static int __init v850e_uart_init (void)
-{
- int rval;
-
- printk (KERN_INFO "%s on-chip UART\n", V850E_UART_CHIP_NAME);
-
- rval = uart_register_driver (&v850e_uart_driver);
- if (rval == 0) {
- unsigned chan;
-
- for (chan = 0; chan < V850E_UART_NUM_CHANNELS; chan++) {
- struct uart_port *port = &v850e_uart_ports[chan];
-
- memset (port, 0, sizeof *port);
-
- port->ops = &v850e_uart_ops;
- port->line = chan;
- port->iotype = UPIO_MEM;
- port->flags = UPF_BOOT_AUTOCONF;
-
- /* We actually use multiple IRQs, but the serial
- framework seems to mainly use this for
- informational purposes anyway. Here we use the TX
- irq. */
- port->irq = V850E_UART_TX_IRQ (chan);
-
- /* The serial framework doesn't really use these
- membase/mapbase fields for anything useful, but
- it requires that they be something non-zero to
- consider the port `valid', and also uses them
- for informational purposes. */
- port->membase = (void *)V850E_UART_BASE_ADDR (chan);
- port->mapbase = V850E_UART_BASE_ADDR (chan);
-
- /* The framework insists on knowing the uart's master
- clock freq, though it doesn't seem to do anything
- useful for us with it. We must make it at least
- higher than (the maximum baud rate * 16), otherwise
- the framework will puke during its internal
- calculations, and force the baud rate to be 9600.
- To be accurate though, just repeat the calculation
- we use when actually setting the speed. */
- port->uartclk = v850e_uart_max_clock() * 16;
-
- uart_add_one_port (&v850e_uart_driver, port);
- }
- }
-
- return rval;
-}
-
-static void __exit v850e_uart_exit (void)
-{
- unsigned chan;
-
- for (chan = 0; chan < V850E_UART_NUM_CHANNELS; chan++)
- uart_remove_one_port (&v850e_uart_driver,
- &v850e_uart_ports[chan]);
-
- uart_unregister_driver (&v850e_uart_driver);
-}
-
-module_init (v850e_uart_init);
-module_exit (v850e_uart_exit);
-
-MODULE_AUTHOR ("Miles Bader");
-MODULE_DESCRIPTION ("NEC " V850E_UART_CHIP_NAME " on-chip UART");
-MODULE_LICENSE ("GPL");
* Core maple bus functionality
*
* Copyright (C) 2007, 2008 Adrian McMenamin
+ * Copyright (C) 2001 - 2008 Paul Mundt
*
* Based on 2.4 code by:
*
#include <linux/slab.h>
#include <linux/maple.h>
#include <linux/dma-mapping.h>
+#include <linux/delay.h>
#include <asm/cacheflush.h>
#include <asm/dma.h>
#include <asm/io.h>
-#include <asm/mach/dma.h>
-#include <asm/mach/sysasic.h>
-#include <asm/mach/maple.h>
-#include <linux/delay.h>
+#include <mach/dma.h>
+#include <mach/sysasic.h>
-MODULE_AUTHOR("Yaegshi Takeshi, Paul Mundt, M.R. Brown, Adrian McMenamin");
+MODULE_AUTHOR("Yaegashi Takeshi, Paul Mundt, M. R. Brown, Adrian McMenamin");
MODULE_DESCRIPTION("Maple bus driver for Dreamcast");
MODULE_LICENSE("GPL v2");
MODULE_SUPPORTED_DEVICE("{{SEGA, Dreamcast/Maple}}");
static LIST_HEAD(maple_waitq);
static LIST_HEAD(maple_sentq);
-static DEFINE_MUTEX(maple_list_lock);
+/* mutex to protect queue of waiting packets */
+static DEFINE_MUTEX(maple_wlist_lock);
static struct maple_driver maple_dummy_driver;
static struct device maple_bus;
static int subdevice_map[MAPLE_PORTS];
static unsigned long *maple_sendbuf, *maple_sendptr, *maple_lastptr;
static unsigned long maple_pnp_time;
-static int started, scanning, liststatus, fullscan;
+static int started, scanning, fullscan;
static struct kmem_cache *maple_queue_cache;
struct maple_device_specify {
static struct maple_device *baseunits[4];
/**
- * maple_driver_register - register a device driver
- * automatically makes the driver bus a maple bus
- * @drv: the driver to be registered
+ * maple_driver_register - register a maple driver
+ * @drv: maple driver to be registered.
+ *
+ * Registers the passed in @drv, while updating the bus type.
+ * Devices with matching function IDs will be automatically probed.
*/
-int maple_driver_register(struct device_driver *drv)
+int maple_driver_register(struct maple_driver *drv)
{
if (!drv)
return -EINVAL;
- drv->bus = &maple_bus_type;
- return driver_register(drv);
+
+ drv->drv.bus = &maple_bus_type;
+
+ return driver_register(&drv->drv);
}
EXPORT_SYMBOL_GPL(maple_driver_register);
+/**
+ * maple_driver_unregister - unregister a maple driver.
+ * @drv: maple driver to unregister.
+ *
+ * Cleans up after maple_driver_register(). To be invoked in the exit
+ * path of any module drivers.
+ */
+void maple_driver_unregister(struct maple_driver *drv)
+{
+ driver_unregister(&drv->drv);
+}
+EXPORT_SYMBOL_GPL(maple_driver_unregister);
+
/* set hardware registers to enable next round of dma */
static void maplebus_dma_reset(void)
{
/**
* maple_add_packet - add a single instruction to the queue
- * @mq: instruction to add to waiting queue
+ * @mdev: maple device
+ * @function: function on device being queried
+ * @command: maple command to add
+ * @length: length of command string (in 32 bit words)
+ * @data: remainder of command string
*/
-void maple_add_packet(struct mapleq *mq)
+int maple_add_packet(struct maple_device *mdev, u32 function, u32 command,
+ size_t length, void *data)
{
- mutex_lock(&maple_list_lock);
- list_add(&mq->list, &maple_waitq);
- mutex_unlock(&maple_list_lock);
+ int locking, ret = 0;
+ void *sendbuf = NULL;
+
+ mutex_lock(&maple_wlist_lock);
+ /* bounce if device already locked */
+ locking = mutex_is_locked(&mdev->mq->mutex);
+ if (locking) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ mutex_lock(&mdev->mq->mutex);
+
+ if (length) {
+ sendbuf = kmalloc(length * 4, GFP_KERNEL);
+ if (!sendbuf) {
+ mutex_unlock(&mdev->mq->mutex);
+ ret = -ENOMEM;
+ goto out;
+ }
+ ((__be32 *)sendbuf)[0] = cpu_to_be32(function);
+ }
+
+ mdev->mq->command = command;
+ mdev->mq->length = length;
+ if (length > 1)
+ memcpy(sendbuf + 4, data, (length - 1) * 4);
+ mdev->mq->sendbuf = sendbuf;
+
+ list_add(&mdev->mq->list, &maple_waitq);
+out:
+ mutex_unlock(&maple_wlist_lock);
+ return ret;
}
EXPORT_SYMBOL_GPL(maple_add_packet);
+/**
+ * maple_add_packet_sleeps - add a single instruction to the queue
+ * @mdev: maple device
+ * @function: function on device being queried
+ * @command: maple command to add
+ * @length: length of command string (in 32 bit words)
+ * @data: remainder of command string
+ *
+ * Same as maple_add_packet(), but waits for the lock to become free.
+ */
+int maple_add_packet_sleeps(struct maple_device *mdev, u32 function,
+ u32 command, size_t length, void *data)
+{
+ int locking, ret = 0;
+ void *sendbuf = NULL;
+
+ locking = mutex_lock_interruptible(&mdev->mq->mutex);
+ if (locking) {
+ ret = -EIO;
+ goto out;
+ }
+
+ if (length) {
+ sendbuf = kmalloc(length * 4, GFP_KERNEL);
+ if (!sendbuf) {
+ mutex_unlock(&mdev->mq->mutex);
+ ret = -ENOMEM;
+ goto out;
+ }
+ ((__be32 *)sendbuf)[0] = cpu_to_be32(function);
+ }
+
+ mdev->mq->command = command;
+ mdev->mq->length = length;
+ if (length > 1)
+ memcpy(sendbuf + 4, data, (length - 1) * 4);
+ mdev->mq->sendbuf = sendbuf;
+
+ mutex_lock(&maple_wlist_lock);
+ list_add(&mdev->mq->list, &maple_waitq);
+ mutex_unlock(&maple_wlist_lock);
+out:
+ return ret;
+}
+EXPORT_SYMBOL_GPL(maple_add_packet_sleeps);
+
static struct mapleq *maple_allocq(struct maple_device *mdev)
{
struct mapleq *mq;
mq = kmalloc(sizeof(*mq), GFP_KERNEL);
if (!mq)
- return NULL;
+ goto failed_nomem;
mq->dev = mdev;
mq->recvbufdcsp = kmem_cache_zalloc(maple_queue_cache, GFP_KERNEL);
mq->recvbuf = (void *) P2SEGADDR(mq->recvbufdcsp);
- if (!mq->recvbuf) {
- kfree(mq);
- return NULL;
- }
+ if (!mq->recvbuf)
+ goto failed_p2;
+ /*
+ * most devices do not need the mutex - but
+ * anything that injects block reads or writes
+ * will rely on it
+ */
+ mutex_init(&mq->mutex);
return mq;
+
+failed_p2:
+ kfree(mq);
+failed_nomem:
+ return NULL;
}
static struct maple_device *maple_alloc_dev(int port, int unit)
}
mdev->dev.bus = &maple_bus_type;
mdev->dev.parent = &maple_bus;
- mdev->function = 0;
return mdev;
}
*maple_sendptr++ = PHYSADDR(mq->recvbuf);
*maple_sendptr++ =
mq->command | (to << 8) | (from << 16) | (len << 24);
-
while (len-- > 0)
*maple_sendptr++ = *lsendbuf++;
}
/* build up command queue */
static void maple_send(void)
{
- int i;
- int maple_packets;
+ int i, maple_packets = 0;
struct mapleq *mq, *nmq;
if (!list_empty(&maple_sentq))
return;
- if (list_empty(&maple_waitq) || !maple_dma_done())
+ mutex_lock(&maple_wlist_lock);
+ if (list_empty(&maple_waitq) || !maple_dma_done()) {
+ mutex_unlock(&maple_wlist_lock);
return;
- maple_packets = 0;
- maple_sendptr = maple_lastptr = maple_sendbuf;
+ }
+ mutex_unlock(&maple_wlist_lock);
+ maple_lastptr = maple_sendbuf;
+ maple_sendptr = maple_sendbuf;
+ mutex_lock(&maple_wlist_lock);
list_for_each_entry_safe(mq, nmq, &maple_waitq, list) {
maple_build_block(mq);
list_move(&mq->list, &maple_sentq);
if (maple_packets++ > MAPLE_MAXPACKETS)
break;
}
+ mutex_unlock(&maple_wlist_lock);
if (maple_packets > 0) {
for (i = 0; i < (1 << MAPLE_DMA_PAGES); i++)
dma_cache_sync(0, maple_sendbuf + i * PAGE_SIZE,
}
}
-static int attach_matching_maple_driver(struct device_driver *driver,
+/* check if there is a driver registered likely to match this device */
+static int check_matching_maple_driver(struct device_driver *driver,
void *devptr)
{
struct maple_driver *maple_drv;
mdev = devptr;
maple_drv = to_maple_driver(driver);
- if (mdev->devinfo.function & be32_to_cpu(maple_drv->function)) {
- if (maple_drv->connect(mdev) == 0) {
- mdev->driver = maple_drv;
- return 1;
- }
- }
+ if (mdev->devinfo.function & cpu_to_be32(maple_drv->function))
+ return 1;
return 0;
}
{
if (!mdev)
return;
- if (mdev->driver) {
- if (mdev->driver->disconnect)
- mdev->driver->disconnect(mdev);
- }
- mdev->driver = NULL;
device_unregister(&mdev->dev);
mdev = NULL;
}
mdev->port, mdev->unit, function);
matched =
- bus_for_each_drv(&maple_bus_type, NULL, mdev,
- attach_matching_maple_driver);
+ bus_for_each_drv(&maple_bus_type, NULL, mdev,
+ check_matching_maple_driver);
if (matched == 0) {
/* Driver does not exist yet */
static int setup_maple_commands(struct device *device, void *ignored)
{
+ int add;
struct maple_device *maple_dev = to_maple_dev(device);
if ((maple_dev->interval > 0)
&& time_after(jiffies, maple_dev->when)) {
- maple_dev->when = jiffies + maple_dev->interval;
- maple_dev->mq->command = MAPLE_COMMAND_GETCOND;
- maple_dev->mq->sendbuf = &maple_dev->function;
- maple_dev->mq->length = 1;
- maple_add_packet(maple_dev->mq);
- liststatus++;
+ /* bounce if we cannot lock */
+ add = maple_add_packet(maple_dev,
+ be32_to_cpu(maple_dev->devinfo.function),
+ MAPLE_COMMAND_GETCOND, 1, NULL);
+ if (!add)
+ maple_dev->when = jiffies + maple_dev->interval;
} else {
- if (time_after(jiffies, maple_pnp_time)) {
- maple_dev->mq->command = MAPLE_COMMAND_DEVINFO;
- maple_dev->mq->length = 0;
- maple_add_packet(maple_dev->mq);
- liststatus++;
- }
+ if (time_after(jiffies, maple_pnp_time))
+ /* This will also bounce */
+ maple_add_packet(maple_dev, 0,
+ MAPLE_COMMAND_DEVINFO, 0, NULL);
}
-
return 0;
}
/* VBLANK bottom half - implemented via workqueue */
static void maple_vblank_handler(struct work_struct *work)
{
- if (!maple_dma_done())
- return;
- if (!list_empty(&maple_sentq))
+ if (!list_empty(&maple_sentq) || !maple_dma_done())
return;
+
ctrl_outl(0, MAPLE_ENABLE);
- liststatus = 0;
+
bus_for_each_dev(&maple_bus_type, NULL, NULL,
setup_maple_commands);
+
if (time_after(jiffies, maple_pnp_time))
maple_pnp_time = jiffies + MAPLE_PNP_INTERVAL;
- if (liststatus && list_empty(&maple_sentq)) {
- INIT_LIST_HEAD(&maple_sentq);
+
+ mutex_lock(&maple_wlist_lock);
+ if (!list_empty(&maple_waitq) && list_empty(&maple_sentq)) {
+ mutex_unlock(&maple_wlist_lock);
maple_send();
+ } else {
+ mutex_unlock(&maple_wlist_lock);
}
+
maplebus_dma_reset();
}
struct maple_device *mdev_add;
struct maple_device_specify ds;
+ ds.port = mdev->port;
for (k = 0; k < 5; k++) {
- ds.port = mdev->port;
ds.unit = k + 1;
retval =
bus_for_each_dev(&maple_bus_type, NULL, &ds,
mdev_add = maple_alloc_dev(mdev->port, k + 1);
if (!mdev_add)
return;
- mdev_add->mq->command = MAPLE_COMMAND_DEVINFO;
- mdev_add->mq->length = 0;
- maple_add_packet(mdev_add->mq);
+ maple_add_packet(mdev_add, 0, MAPLE_COMMAND_DEVINFO,
+ 0, NULL);
+ /* mark that we are checking sub devices */
scanning = 1;
}
submask = submask >> 1;
}
}
+static void maple_port_rescan(void)
+{
+ int i;
+ struct maple_device *mdev;
+
+ fullscan = 1;
+ for (i = 0; i < MAPLE_PORTS; i++) {
+ if (checked[i] == false) {
+ fullscan = 0;
+ mdev = baseunits[i];
+ /*
+ * test lock in case scan has failed
+ * but device is still locked
+ */
+ if (mutex_is_locked(&mdev->mq->mutex))
+ mutex_unlock(&mdev->mq->mutex);
+ maple_add_packet(mdev, 0, MAPLE_COMMAND_DEVINFO,
+ 0, NULL);
+ }
+ }
+}
+
/* maple dma end bottom half - implemented via workqueue */
static void maple_dma_handler(struct work_struct *work)
{
struct maple_device *dev;
char *recvbuf;
enum maple_code code;
- int i;
if (!maple_dma_done())
return;
recvbuf = mq->recvbuf;
code = recvbuf[0];
dev = mq->dev;
+ kfree(mq->sendbuf);
+ mutex_unlock(&mq->mutex);
+ list_del_init(&mq->list);
+
switch (code) {
case MAPLE_RESPONSE_NONE:
maple_response_none(dev, mq);
break;
}
}
- INIT_LIST_HEAD(&maple_sentq);
+ /* if scanning is 1 then we have subdevices to check */
if (scanning == 1) {
maple_send();
scanning = 2;
} else
scanning = 0;
-
- if (!fullscan) {
- fullscan = 1;
- for (i = 0; i < MAPLE_PORTS; i++) {
- if (checked[i] == false) {
- fullscan = 0;
- dev = baseunits[i];
- dev->mq->command =
- MAPLE_COMMAND_DEVINFO;
- dev->mq->length = 0;
- maple_add_packet(dev->mq);
- }
- }
- }
+ /*check if we have actually tested all ports yet */
+ if (!fullscan)
+ maple_port_rescan();
+ /* mark that we have been through the first scan */
if (started == 0)
started = 1;
}
static int match_maple_bus_driver(struct device *devptr,
struct device_driver *drvptr)
{
- struct maple_driver *maple_drv;
- struct maple_device *maple_dev;
+ struct maple_driver *maple_drv = to_maple_driver(drvptr);
+ struct maple_device *maple_dev = to_maple_dev(devptr);
- maple_drv = container_of(drvptr, struct maple_driver, drv);
- maple_dev = container_of(devptr, struct maple_device, dev);
/* Trap empty port case */
if (maple_dev->devinfo.function == 0xFFFFFFFF)
return 0;
else if (maple_dev->devinfo.function &
- be32_to_cpu(maple_drv->function))
+ cpu_to_be32(maple_drv->function))
return 1;
return 0;
}
if (!maple_queue_cache)
goto cleanup_bothirqs;
+ INIT_LIST_HEAD(&maple_waitq);
+ INIT_LIST_HEAD(&maple_sentq);
+
/* setup maple ports */
for (i = 0; i < MAPLE_PORTS; i++) {
checked[i] = false;
maple_free_dev(mdev[i]);
goto cleanup_cache;
}
- mdev[i]->mq->command = MAPLE_COMMAND_DEVINFO;
- mdev[i]->mq->length = 0;
- maple_add_packet(mdev[i]->mq);
+ maple_add_packet(mdev[i], 0, MAPLE_COMMAND_DEVINFO, 0, NULL);
subdevice_map[i] = 0;
}
SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI
(McSPI) modules.
+config SPI_ORION
+ tristate "Orion SPI master (EXPERIMENTAL)"
+ depends on PLAT_ORION && EXPERIMENTAL
+ help
+ This enables using the SPI master controller on the Orion chips.
+
config SPI_PXA2XX
tristate "PXA2xx SSP SPI master"
depends on ARCH_PXA && EXPERIMENTAL
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
obj-$(CONFIG_SPI_OMAP24XX) += omap2_mcspi.o
+obj-$(CONFIG_SPI_ORION) += orion_spi.o
obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52xx_psc_spi.o
obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
#include <linux/spi/spi.h>
#include <asm/io.h>
-#include <asm/arch/board.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/cpu.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/cpu.h>
#include "atmel_spi.h"
{
struct atmel_spi *as = spi_master_get_devdata(master);
struct spi_transfer *xfer;
- u32 len, remaining, total;
+ u32 len, remaining;
+ u32 ieval;
dma_addr_t tx_dma, rx_dma;
if (!as->current_transfer)
xfer = NULL;
if (xfer) {
+ spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
+
len = xfer->len;
atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
remaining = xfer->len - len;
as->next_transfer = xfer;
if (xfer) {
+ u32 total;
+
total = len;
atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
as->next_remaining_bytes = total - len;
" next xfer %p: len %u tx %p/%08x rx %p/%08x\n",
xfer, xfer->len, xfer->tx_buf, xfer->tx_dma,
xfer->rx_buf, xfer->rx_dma);
+ ieval = SPI_BIT(ENDRX) | SPI_BIT(OVRES);
} else {
spi_writel(as, RNCR, 0);
spi_writel(as, TNCR, 0);
+ ieval = SPI_BIT(RXBUFF) | SPI_BIT(ENDRX) | SPI_BIT(OVRES);
}
/* REVISIT: We're waiting for ENDRX before we start the next
*
* It should be doable, though. Just not now...
*/
- spi_writel(as, IER, SPI_BIT(ENDRX) | SPI_BIT(OVRES));
+ spi_writel(as, IER, ieval);
spi_writel(as, PTCR, SPI_BIT(TXTEN) | SPI_BIT(RXTEN));
}
ret = IRQ_HANDLED;
- spi_writel(as, IDR, (SPI_BIT(ENDTX) | SPI_BIT(ENDRX)
+ spi_writel(as, IDR, (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX)
| SPI_BIT(OVRES)));
/*
if (xfer->delay_usecs)
udelay(xfer->delay_usecs);
- dev_warn(master->dev.parent, "fifo overrun (%u/%u remaining)\n",
+ dev_warn(master->dev.parent, "overrun (%u/%u remaining)\n",
spi_readl(as, TCR), spi_readl(as, RCR));
/*
spi_readl(as, SR);
atmel_spi_msg_done(master, as, msg, -EIO, 0);
- } else if (pending & SPI_BIT(ENDRX)) {
+ } else if (pending & (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX))) {
ret = IRQ_HANDLED;
spi_writel(as, IDR, pending);
#include <linux/spi/spi.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/clock.h>
+#include <mach/dma.h>
+#include <mach/clock.h>
#define OMAP2_MCSPI_MAX_FREQ 48000000
#include <asm/system.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/omap730.h> /* OMAP730_IO_CONF registers */
+#include <mach/mux.h>
+#include <mach/omap730.h> /* OMAP730_IO_CONF registers */
/* FIXME address is now a platform device resource,
--- /dev/null
+/*
+ * orion_spi.c -- Marvell Orion SPI controller driver
+ *
+ * Author: Shadi Ammouri <shadi@marvell.com>
+ * Copyright (C) 2007-2008 Marvell Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <asm/unaligned.h>
+
+#define DRIVER_NAME "orion_spi"
+
+#define ORION_NUM_CHIPSELECTS 1 /* only one slave is supported*/
+#define ORION_SPI_WAIT_RDY_MAX_LOOP 2000 /* in usec */
+
+#define ORION_SPI_IF_CTRL_REG 0x00
+#define ORION_SPI_IF_CONFIG_REG 0x04
+#define ORION_SPI_DATA_OUT_REG 0x08
+#define ORION_SPI_DATA_IN_REG 0x0c
+#define ORION_SPI_INT_CAUSE_REG 0x10
+
+#define ORION_SPI_IF_8_16_BIT_MODE (1 << 5)
+#define ORION_SPI_CLK_PRESCALE_MASK 0x1F
+
+struct orion_spi {
+ struct work_struct work;
+
+ /* Lock access to transfer list. */
+ spinlock_t lock;
+
+ struct list_head msg_queue;
+ struct spi_master *master;
+ void __iomem *base;
+ unsigned int max_speed;
+ unsigned int min_speed;
+ struct orion_spi_info *spi_info;
+};
+
+static struct workqueue_struct *orion_spi_wq;
+
+static inline void __iomem *spi_reg(struct orion_spi *orion_spi, u32 reg)
+{
+ return orion_spi->base + reg;
+}
+
+static inline void
+orion_spi_setbits(struct orion_spi *orion_spi, u32 reg, u32 mask)
+{
+ void __iomem *reg_addr = spi_reg(orion_spi, reg);
+ u32 val;
+
+ val = readl(reg_addr);
+ val |= mask;
+ writel(val, reg_addr);
+}
+
+static inline void
+orion_spi_clrbits(struct orion_spi *orion_spi, u32 reg, u32 mask)
+{
+ void __iomem *reg_addr = spi_reg(orion_spi, reg);
+ u32 val;
+
+ val = readl(reg_addr);
+ val &= ~mask;
+ writel(val, reg_addr);
+}
+
+static int orion_spi_set_transfer_size(struct orion_spi *orion_spi, int size)
+{
+ if (size == 16) {
+ orion_spi_setbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
+ ORION_SPI_IF_8_16_BIT_MODE);
+ } else if (size == 8) {
+ orion_spi_clrbits(orion_spi, ORION_SPI_IF_CONFIG_REG,
+ ORION_SPI_IF_8_16_BIT_MODE);
+ } else {
+ pr_debug("Bad bits per word value %d (only 8 or 16 are "
+ "allowed).\n", size);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int orion_spi_baudrate_set(struct spi_device *spi, unsigned int speed)
+{
+ u32 tclk_hz;
+ u32 rate;
+ u32 prescale;
+ u32 reg;
+ struct orion_spi *orion_spi;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+
+ tclk_hz = orion_spi->spi_info->tclk;
+
+ /*
+ * the supported rates are: 4,6,8...30
+ * round up as we look for equal or less speed
+ */
+ rate = DIV_ROUND_UP(tclk_hz, speed);
+ rate = roundup(rate, 2);
+
+ /* check if requested speed is too small */
+ if (rate > 30)
+ return -EINVAL;
+
+ if (rate < 4)
+ rate = 4;
+
+ /* Convert the rate to SPI clock divisor value. */
+ prescale = 0x10 + rate/2;
+
+ reg = readl(spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
+ reg = ((reg & ~ORION_SPI_CLK_PRESCALE_MASK) | prescale);
+ writel(reg, spi_reg(orion_spi, ORION_SPI_IF_CONFIG_REG));
+
+ return 0;
+}
+
+/*
+ * called only when no transfer is active on the bus
+ */
+static int
+orion_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
+{
+ struct orion_spi *orion_spi;
+ unsigned int speed = spi->max_speed_hz;
+ unsigned int bits_per_word = spi->bits_per_word;
+ int rc;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+
+ if ((t != NULL) && t->speed_hz)
+ speed = t->speed_hz;
+
+ if ((t != NULL) && t->bits_per_word)
+ bits_per_word = t->bits_per_word;
+
+ rc = orion_spi_baudrate_set(spi, speed);
+ if (rc)
+ return rc;
+
+ return orion_spi_set_transfer_size(orion_spi, bits_per_word);
+}
+
+static void orion_spi_set_cs(struct orion_spi *orion_spi, int enable)
+{
+ if (enable)
+ orion_spi_setbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1);
+ else
+ orion_spi_clrbits(orion_spi, ORION_SPI_IF_CTRL_REG, 0x1);
+}
+
+static inline int orion_spi_wait_till_ready(struct orion_spi *orion_spi)
+{
+ int i;
+
+ for (i = 0; i < ORION_SPI_WAIT_RDY_MAX_LOOP; i++) {
+ if (readl(spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG)))
+ return 1;
+ else
+ udelay(1);
+ }
+
+ return -1;
+}
+
+static inline int
+orion_spi_write_read_8bit(struct spi_device *spi,
+ const u8 **tx_buf, u8 **rx_buf)
+{
+ void __iomem *tx_reg, *rx_reg, *int_reg;
+ struct orion_spi *orion_spi;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+ tx_reg = spi_reg(orion_spi, ORION_SPI_DATA_OUT_REG);
+ rx_reg = spi_reg(orion_spi, ORION_SPI_DATA_IN_REG);
+ int_reg = spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG);
+
+ /* clear the interrupt cause register */
+ writel(0x0, int_reg);
+
+ if (tx_buf && *tx_buf)
+ writel(*(*tx_buf)++, tx_reg);
+ else
+ writel(0, tx_reg);
+
+ if (orion_spi_wait_till_ready(orion_spi) < 0) {
+ dev_err(&spi->dev, "TXS timed out\n");
+ return -1;
+ }
+
+ if (rx_buf && *rx_buf)
+ *(*rx_buf)++ = readl(rx_reg);
+
+ return 1;
+}
+
+static inline int
+orion_spi_write_read_16bit(struct spi_device *spi,
+ const u16 **tx_buf, u16 **rx_buf)
+{
+ void __iomem *tx_reg, *rx_reg, *int_reg;
+ struct orion_spi *orion_spi;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+ tx_reg = spi_reg(orion_spi, ORION_SPI_DATA_OUT_REG);
+ rx_reg = spi_reg(orion_spi, ORION_SPI_DATA_IN_REG);
+ int_reg = spi_reg(orion_spi, ORION_SPI_INT_CAUSE_REG);
+
+ /* clear the interrupt cause register */
+ writel(0x0, int_reg);
+
+ if (tx_buf && *tx_buf)
+ writel(__cpu_to_le16(get_unaligned((*tx_buf)++)), tx_reg);
+ else
+ writel(0, tx_reg);
+
+ if (orion_spi_wait_till_ready(orion_spi) < 0) {
+ dev_err(&spi->dev, "TXS timed out\n");
+ return -1;
+ }
+
+ if (rx_buf && *rx_buf)
+ put_unaligned(__le16_to_cpu(readl(rx_reg)), (*rx_buf)++);
+
+ return 1;
+}
+
+static unsigned int
+orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
+{
+ struct orion_spi *orion_spi;
+ unsigned int count;
+ int word_len;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+ word_len = spi->bits_per_word;
+ count = xfer->len;
+
+ if (word_len == 8) {
+ const u8 *tx = xfer->tx_buf;
+ u8 *rx = xfer->rx_buf;
+
+ do {
+ if (orion_spi_write_read_8bit(spi, &tx, &rx) < 0)
+ goto out;
+ count--;
+ } while (count);
+ } else if (word_len == 16) {
+ const u16 *tx = xfer->tx_buf;
+ u16 *rx = xfer->rx_buf;
+
+ do {
+ if (orion_spi_write_read_16bit(spi, &tx, &rx) < 0)
+ goto out;
+ count -= 2;
+ } while (count);
+ }
+
+out:
+ return xfer->len - count;
+}
+
+
+static void orion_spi_work(struct work_struct *work)
+{
+ struct orion_spi *orion_spi =
+ container_of(work, struct orion_spi, work);
+
+ spin_lock_irq(&orion_spi->lock);
+ while (!list_empty(&orion_spi->msg_queue)) {
+ struct spi_message *m;
+ struct spi_device *spi;
+ struct spi_transfer *t = NULL;
+ int par_override = 0;
+ int status = 0;
+ int cs_active = 0;
+
+ m = container_of(orion_spi->msg_queue.next, struct spi_message,
+ queue);
+
+ list_del_init(&m->queue);
+ spin_unlock_irq(&orion_spi->lock);
+
+ spi = m->spi;
+
+ /* Load defaults */
+ status = orion_spi_setup_transfer(spi, NULL);
+
+ if (status < 0)
+ goto msg_done;
+
+ list_for_each_entry(t, &m->transfers, transfer_list) {
+ if (par_override || t->speed_hz || t->bits_per_word) {
+ par_override = 1;
+ status = orion_spi_setup_transfer(spi, t);
+ if (status < 0)
+ break;
+ if (!t->speed_hz && !t->bits_per_word)
+ par_override = 0;
+ }
+
+ if (!cs_active) {
+ orion_spi_set_cs(orion_spi, 1);
+ cs_active = 1;
+ }
+
+ if (t->len)
+ m->actual_length +=
+ orion_spi_write_read(spi, t);
+
+ if (t->delay_usecs)
+ udelay(t->delay_usecs);
+
+ if (t->cs_change) {
+ orion_spi_set_cs(orion_spi, 0);
+ cs_active = 0;
+ }
+ }
+
+msg_done:
+ if (cs_active)
+ orion_spi_set_cs(orion_spi, 0);
+
+ m->status = status;
+ m->complete(m->context);
+
+ spin_lock_irq(&orion_spi->lock);
+ }
+
+ spin_unlock_irq(&orion_spi->lock);
+}
+
+static int __init orion_spi_reset(struct orion_spi *orion_spi)
+{
+ /* Verify that the CS is deasserted */
+ orion_spi_set_cs(orion_spi, 0);
+
+ return 0;
+}
+
+static int orion_spi_setup(struct spi_device *spi)
+{
+ struct orion_spi *orion_spi;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+
+ if (spi->mode) {
+ dev_err(&spi->dev, "setup: unsupported mode bits %x\n",
+ spi->mode);
+ return -EINVAL;
+ }
+
+ if (spi->bits_per_word == 0)
+ spi->bits_per_word = 8;
+
+ if ((spi->max_speed_hz == 0)
+ || (spi->max_speed_hz > orion_spi->max_speed))
+ spi->max_speed_hz = orion_spi->max_speed;
+
+ if (spi->max_speed_hz < orion_spi->min_speed) {
+ dev_err(&spi->dev, "setup: requested speed too low %d Hz\n",
+ spi->max_speed_hz);
+ return -EINVAL;
+ }
+
+ /*
+ * baudrate & width will be set orion_spi_setup_transfer
+ */
+ return 0;
+}
+
+static int orion_spi_transfer(struct spi_device *spi, struct spi_message *m)
+{
+ struct orion_spi *orion_spi;
+ struct spi_transfer *t = NULL;
+ unsigned long flags;
+
+ m->actual_length = 0;
+ m->status = 0;
+
+ /* reject invalid messages and transfers */
+ if (list_empty(&m->transfers) || !m->complete)
+ return -EINVAL;
+
+ orion_spi = spi_master_get_devdata(spi->master);
+
+ list_for_each_entry(t, &m->transfers, transfer_list) {
+ unsigned int bits_per_word = spi->bits_per_word;
+
+ if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
+ dev_err(&spi->dev,
+ "message rejected : "
+ "invalid transfer data buffers\n");
+ goto msg_rejected;
+ }
+
+ if ((t != NULL) && t->bits_per_word)
+ bits_per_word = t->bits_per_word;
+
+ if ((bits_per_word != 8) && (bits_per_word != 16)) {
+ dev_err(&spi->dev,
+ "message rejected : "
+ "invalid transfer bits_per_word (%d bits)\n",
+ bits_per_word);
+ goto msg_rejected;
+ }
+ /*make sure buffer length is even when working in 16 bit mode*/
+ if ((t != NULL) && (t->bits_per_word == 16) && (t->len & 1)) {
+ dev_err(&spi->dev,
+ "message rejected : "
+ "odd data length (%d) while in 16 bit mode\n",
+ t->len);
+ goto msg_rejected;
+ }
+
+ if (t->speed_hz < orion_spi->min_speed) {
+ dev_err(&spi->dev,
+ "message rejected : "
+ "device min speed (%d Hz) exceeds "
+ "required transfer speed (%d Hz)\n",
+ orion_spi->min_speed, t->speed_hz);
+ goto msg_rejected;
+ }
+ }
+
+
+ spin_lock_irqsave(&orion_spi->lock, flags);
+ list_add_tail(&m->queue, &orion_spi->msg_queue);
+ queue_work(orion_spi_wq, &orion_spi->work);
+ spin_unlock_irqrestore(&orion_spi->lock, flags);
+
+ return 0;
+msg_rejected:
+ /* Message rejected and not queued */
+ m->status = -EINVAL;
+ if (m->complete)
+ m->complete(m->context);
+ return -EINVAL;
+}
+
+static int __init orion_spi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct orion_spi *spi;
+ struct resource *r;
+ struct orion_spi_info *spi_info;
+ int status = 0;
+
+ spi_info = pdev->dev.platform_data;
+
+ master = spi_alloc_master(&pdev->dev, sizeof *spi);
+ if (master == NULL) {
+ dev_dbg(&pdev->dev, "master allocation failed\n");
+ return -ENOMEM;
+ }
+
+ if (pdev->id != -1)
+ master->bus_num = pdev->id;
+
+ master->setup = orion_spi_setup;
+ master->transfer = orion_spi_transfer;
+ master->num_chipselect = ORION_NUM_CHIPSELECTS;
+
+ dev_set_drvdata(&pdev->dev, master);
+
+ spi = spi_master_get_devdata(master);
+ spi->master = master;
+ spi->spi_info = spi_info;
+
+ spi->max_speed = DIV_ROUND_UP(spi_info->tclk, 4);
+ spi->min_speed = DIV_ROUND_UP(spi_info->tclk, 30);
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ status = -ENODEV;
+ goto out;
+ }
+
+ if (!request_mem_region(r->start, (r->end - r->start) + 1,
+ pdev->dev.bus_id)) {
+ status = -EBUSY;
+ goto out;
+ }
+ spi->base = ioremap(r->start, SZ_1K);
+
+ INIT_WORK(&spi->work, orion_spi_work);
+
+ spin_lock_init(&spi->lock);
+ INIT_LIST_HEAD(&spi->msg_queue);
+
+ if (orion_spi_reset(spi) < 0)
+ goto out_rel_mem;
+
+ status = spi_register_master(master);
+ if (status < 0)
+ goto out_rel_mem;
+
+ return status;
+
+out_rel_mem:
+ release_mem_region(r->start, (r->end - r->start) + 1);
+
+out:
+ spi_master_put(master);
+ return status;
+}
+
+
+static int __exit orion_spi_remove(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct orion_spi *spi;
+ struct resource *r;
+
+ master = dev_get_drvdata(&pdev->dev);
+ spi = spi_master_get_devdata(master);
+
+ cancel_work_sync(&spi->work);
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(r->start, (r->end - r->start) + 1);
+
+ spi_unregister_master(master);
+
+ return 0;
+}
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+
+static struct platform_driver orion_spi_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(orion_spi_remove),
+};
+
+static int __init orion_spi_init(void)
+{
+ orion_spi_wq = create_singlethread_workqueue(
+ orion_spi_driver.driver.name);
+ if (orion_spi_wq == NULL)
+ return -ENOMEM;
+
+ return platform_driver_probe(&orion_spi_driver, orion_spi_probe);
+}
+module_init(orion_spi_init);
+
+static void __exit orion_spi_exit(void)
+{
+ flush_workqueue(orion_spi_wq);
+ platform_driver_unregister(&orion_spi_driver);
+
+ destroy_workqueue(orion_spi_wq);
+}
+module_exit(orion_spi_exit);
+
+MODULE_DESCRIPTION("Orion SPI driver");
+MODULE_AUTHOR("Shadi Ammouri <shadi@marvell.com>");
+MODULE_LICENSE("GPL");
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
#include <asm/delay.h>
#include <asm/dma.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/regs-ssp.h>
-#include <asm/arch/ssp.h>
-#include <asm/arch/pxa2xx_spi.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/regs-ssp.h>
+#include <mach/ssp.h>
+#include <mach/pxa2xx_spi.h>
MODULE_AUTHOR("Stephen Street");
MODULE_DESCRIPTION("PXA2xx SSP SPI Controller");
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/hardware.h>
#include <asm/delay.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/imx-dma.h>
-#include <asm/arch/spi_imx.h>
+#include <mach/hardware.h>
+#include <mach/imx-dma.h>
+#include <mach/spi_imx.h>
/*-------------------------------------------------------------------------*/
/* SPI Registers offsets from peripheral base address */
#include <asm/io.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/regs-spi.h>
-#include <asm/arch/spi.h>
+#include <mach/spi.h>
struct s3c24xx_spi {
/* bitbang has to be first */
return IRQ_HANDLED;
}
+static void s3c24xx_spi_initialsetup(struct s3c24xx_spi *hw)
+{
+ /* for the moment, permanently enable the clock */
+
+ clk_enable(hw->clk);
+
+ /* program defaults into the registers */
+
+ writeb(0xff, hw->regs + S3C2410_SPPRE);
+ writeb(SPPIN_DEFAULT, hw->regs + S3C2410_SPPIN);
+ writeb(SPCON_DEFAULT, hw->regs + S3C2410_SPCON);
+}
+
static int __init s3c24xx_spi_probe(struct platform_device *pdev)
{
struct s3c2410_spi_info *pdata;
goto err_no_clk;
}
- /* for the moment, permanently enable the clock */
-
- clk_enable(hw->clk);
-
- /* program defaults into the registers */
-
- writeb(0xff, hw->regs + S3C2410_SPPRE);
- writeb(SPPIN_DEFAULT, hw->regs + S3C2410_SPPIN);
- writeb(SPCON_DEFAULT, hw->regs + S3C2410_SPCON);
+ s3c24xx_spi_initialsetup(hw);
/* setup any gpio we can */
{
struct s3c24xx_spi *hw = platform_get_drvdata(pdev);
- clk_enable(hw->clk);
+ s3c24xx_spi_initialsetup(hw);
return 0;
}
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/spi-gpio.h>
-#include <asm/hardware.h>
+#include <mach/regs-gpio.h>
+#include <mach/spi-gpio.h>
+#include <mach/hardware.h>
struct s3c2410_spigpio {
struct spi_bitbang bitbang;
if (io->entries <= 0)
return io->entries;
- io->count = io->entries;
io->urbs = kmalloc(io->entries * sizeof *io->urbs, mem_flags);
if (!io->urbs)
goto nomem;
io->urbs[--i]->transfer_flags &= ~URB_NO_INTERRUPT;
/* transaction state */
+ io->count = io->entries;
io->status = 0;
io->bytes = 0;
init_completion(&io->complete);
#include <linux/usb/gadget.h>
#include <asm/byteorder.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
-#include <asm/mach-types.h>
#include <asm/gpio.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/at91sam9261_matrix.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
+#include <mach/at91sam9261_matrix.h>
#include "at91_udc.h"
#include <linux/delay.h>
#include <asm/gpio.h>
-#include <asm/arch/board.h>
+#include <mach/board.h>
#include "atmel_usba_udc.h"
#elif defined(CONFIG_ARCH_AT91)
-#include <asm/arch/at91_pmc.h>
+#include <mach/at91_pmc.h>
static void toggle_bias(int is_on)
{
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/unaligned.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
m66592->gadget.ops = &m66592_gadget_ops;
device_initialize(&m66592->gadget.dev);
- dev_set_name(&m66592->gadget, "gadget");
+ dev_set_name(&m66592->gadget.dev, "gadget");
m66592->gadget.is_dualspeed = 1;
m66592->gadget.dev.parent = &pdev->dev;
m66592->gadget.dev.dma_mask = pdev->dev.dma_mask;
#include <asm/unaligned.h>
#include <asm/mach-types.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/usb.h>
+#include <mach/dma.h>
+#include <mach/usb.h>
#include "omap_udc.h"
* This driver is PXA25x only. Grab the right register definitions.
*/
#ifdef CONFIG_ARCH_PXA
-#include <asm/arch/pxa25x-udc.h>
+#include <mach/pxa25x-udc.h>
#endif
#include <asm/mach/udc_pxa2xx.h>
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_ARCH_LUBBOCK
-#include <asm/arch/lubbock.h>
+#include <mach/lubbock.h>
/* lubbock can also report usb connect/disconnect irqs */
#endif
#include <linux/irq.h>
#include <asm/byteorder.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <linux/usb.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
-#include <asm/arch/pxa2xx-regs.h> /* FIXME: for PSSR */
-#include <asm/arch/udc.h>
+#include <mach/pxa2xx-regs.h> /* FIXME: for PSSR */
+#include <mach/udc.h>
#include "pxa27x_udc.h"
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/unaligned.h>
-#include <asm/arch/irqs.h>
+#include <mach/irqs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/regs-gpio.h>
+#include <mach/hardware.h>
+#include <mach/regs-gpio.h>
#include <asm/plat-s3c24xx/regs-udc.h>
#include <asm/plat-s3c24xx/udc.h>
-#include <asm/mach-types.h>
#include "s3c2410_udc.h"
}
}
-#include <asm/arch/regs-irq.h>
+#include <mach/regs-irq.h>
/*
* s3c2410_udc_irq - interrupt handler
list_del (&qtd->qtd_list);
list_add (&dummy->qtd_list, qtd_list);
- __list_splice (qtd_list, qh->qtd_list.prev);
+ list_splice_tail(qtd_list, &qh->qtd_list);
ehci_qtd_init(ehci, qtd, qtd->qtd_dma);
qh->dummy = qtd;
#include <linux/clk.h>
#include <linux/platform_device.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/gpio.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
#ifndef CONFIG_ARCH_AT91
#error "CONFIG_ARCH_AT91 must be defined."
#include <linux/signal.h>
#include <linux/platform_device.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static struct clk *usb_host_clock;
#include <linux/platform_device.h>
#include <linux/signal.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
extern int usb_disabled(void);
#include <linux/platform_device.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/usb.h>
+#include <mach/mux.h>
+#include <mach/irqs.h>
+#include <mach/gpio.h>
+#include <mach/fpga.h>
+#include <mach/usb.h>
/* OMAP-1510 OHCI has its own MMU for DMA */
#include <linux/platform_device.h>
#include <linux/i2c.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/arch/platform.h>
-#include <asm/arch/irqs.h>
-#include <asm/arch/gpio.h>
+#include <mach/platform.h>
+#include <mach/irqs.h>
+#include <mach/gpio.h>
#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
#include <linux/platform_device.h>
#include <linux/clk.h>
-#include <asm/mach-types.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-regs.h> /* FIXME: for PSSR */
-#include <asm/arch/ohci.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h> /* FIXME: for PSSR */
+#include <mach/ohci.h>
#define PXA_UHC_MAX_PORTNUM 3
#include <linux/platform_device.h>
#include <linux/clk.h>
-#include <asm/hardware.h>
-#include <asm/arch/usb-control.h>
+#include <mach/hardware.h>
+#include <mach/usb-control.h>
#define valid_port(idx) ((idx) == 1 || (idx) == 2)
* This file is licenced under the GPL.
*/
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <asm/arch/assabet.h>
-#include <asm/arch/badge4.h>
+#include <mach/assabet.h>
+#include <mach/badge4.h>
#include <asm/hardware/sa1111.h>
#ifndef CONFIG_SA1111
* (http://www.freecom.de/)
*/
-#include <linux/hdreg.h>
-
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
obj-$(CONFIG_FB_SM501) += sm501fb.o
obj-$(CONFIG_FB_XILINX) += xilinxfb.o
obj-$(CONFIG_FB_SH_MOBILE_LCDC) += sh_mobile_lcdcfb.o
-obj-$(CONFIG_FB_SH7343VOU) += sh7343_voufb.o
obj-$(CONFIG_FB_OMAP) += omap/
obj-$(CONFIG_XEN_FBDEV_FRONTEND) += xen-fbfront.o
obj-$(CONFIG_FB_CARMINE) += carminefb.o
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#endif
#ifdef HAS_VIDC20
-#include <asm/arch/acornfb.h>
+#include <mach/acornfb.h>
#define MAX_SIZE 2*1024*1024
#include <video/metronomefb.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
/* register offsets for gpio control */
#define LED_GPIO_PIN 51
/* Prepare PCI device */
rc = pci_enable_device(dev);
if (rc < 0) {
- dev_err(info->dev, "cannot enable PCI device\n");
+ dev_err(info->device, "cannot enable PCI device\n");
goto err_enable_device;
}
rc = pci_request_regions(dev, "arkfb");
if (rc < 0) {
- dev_err(info->dev, "cannot reserve framebuffer region\n");
+ dev_err(info->device, "cannot reserve framebuffer region\n");
goto err_request_regions;
}
par->dac = ics5342_init(ark_dac_read_regs, ark_dac_write_regs, info);
if (! par->dac) {
rc = -ENOMEM;
- dev_err(info->dev, "RAMDAC initialization failed\n");
+ dev_err(info->device, "RAMDAC initialization failed\n");
goto err_dac;
}
info->screen_base = pci_iomap(dev, 0, 0);
if (! info->screen_base) {
rc = -ENOMEM;
- dev_err(info->dev, "iomap for framebuffer failed\n");
+ dev_err(info->device, "iomap for framebuffer failed\n");
goto err_iomap;
}
rc = fb_find_mode(&(info->var), info, mode_option, NULL, 0, NULL, 8);
if (! ((rc == 1) || (rc == 2))) {
rc = -EINVAL;
- dev_err(info->dev, "mode %s not found\n", mode_option);
+ dev_err(info->device, "mode %s not found\n", mode_option);
goto err_find_mode;
}
rc = fb_alloc_cmap(&info->cmap, 256, 0);
if (rc < 0) {
- dev_err(info->dev, "cannot allocate colormap\n");
+ dev_err(info->device, "cannot allocate colormap\n");
goto err_alloc_cmap;
}
rc = register_framebuffer(info);
if (rc < 0) {
- dev_err(info->dev, "cannot register framebugger\n");
+ dev_err(info->device, "cannot register framebugger\n");
goto err_reg_fb;
}
struct fb_info *info = pci_get_drvdata(dev);
struct arkfb_info *par = info->par;
- dev_info(info->dev, "suspend\n");
+ dev_info(info->device, "suspend\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
struct fb_info *info = pci_get_drvdata(dev);
struct arkfb_info *par = info->par;
- dev_info(info->dev, "resume\n");
+ dev_info(info->device, "resume\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
- if (par->ref_count == 0) {
- mutex_unlock(&(par->open_lock));
- release_console_sem();
- return 0;
- }
+ if (par->ref_count == 0)
+ goto fail;
pci_set_power_state(dev, PCI_D0);
pci_restore_state(dev);
arkfb_set_par(info);
fb_set_suspend(info, 0);
- mutex_unlock(&(par->open_lock));
fail:
+ mutex_unlock(&(par->open_lock));
release_console_sem();
return 0;
}
#include <linux/delay.h>
#include <linux/backlight.h>
-#include <asm/arch/board.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/gpio.h>
+#include <mach/board.h>
+#include <mach/cpu.h>
+#include <mach/gpio.h>
#include <video/atmel_lcdc.h>
*/
static int aty_init(struct fb_info *info);
-static void aty_resume_chip(struct fb_info *info);
+
#ifdef CONFIG_ATARI
static int store_video_par(char *videopar, unsigned char m64_num);
#endif
return 0;
}
+static void aty_resume_chip(struct fb_info *info)
+{
+ struct atyfb_par *par = info->par;
+
+ aty_st_le32(MEM_CNTL, par->mem_cntl, par);
+
+ if (par->pll_ops->resume_pll)
+ par->pll_ops->resume_pll(info, &par->pll);
+
+ if (par->aux_start)
+ aty_st_le32(BUS_CNTL,
+ aty_ld_le32(BUS_CNTL, par) | BUS_APER_REG_DIS, par);
+}
+
static int atyfb_pci_resume(struct pci_dev *pdev)
{
struct fb_info *info = pci_get_drvdata(pdev);
return ret;
}
-static void aty_resume_chip(struct fb_info *info)
-{
- struct atyfb_par *par = info->par;
-
- aty_st_le32(MEM_CNTL, par->mem_cntl, par);
-
- if (par->pll_ops->resume_pll)
- par->pll_ops->resume_pll(info, &par->pll);
-
- if (par->aux_start)
- aty_st_le32(BUS_CNTL, aty_ld_le32(BUS_CNTL, par) | BUS_APER_REG_DIS, par);
-}
-
#ifdef CONFIG_ATARI
static int __devinit store_video_par(char *video_str, unsigned char m64_num)
{
INREG(HOST_PATH_CNTL);
OUTREG(HOST_PATH_CNTL, host_path_cntl);
- if (rinfo->family != CHIP_FAMILY_R300 ||
- rinfo->family != CHIP_FAMILY_R350 ||
+ if (rinfo->family != CHIP_FAMILY_R300 &&
+ rinfo->family != CHIP_FAMILY_R350 &&
rinfo->family != CHIP_FAMILY_RV350)
OUTREG(RBBM_SOFT_RESET, rbbm_soft_reset);
{
int rc;
- strcpy(chan->adapter.name, name);
+ snprintf(chan->adapter.name, sizeof(chan->adapter.name),
+ "radeonfb %s", name);
chan->adapter.owner = THIS_MODULE;
chan->adapter.id = I2C_HW_B_RADEON;
chan->adapter.algo_data = &chan->algo;
#include <linux/fb.h>
#include <linux/backlight.h>
-#include <asm/cpu/dac.h>
+#include <cpu/dac.h>
#include <asm/hp6xx.h>
#include <asm/hd64461.h>
#include <linux/fb.h>
#include <linux/backlight.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/board.h>
-#include <asm/arch/mux.h>
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/mux.h>
#define OMAPBL_MAX_INTENSITY 0xff
plcd->us = dev;
plcd->pdata = pdata;
- plcd->lcd = lcd_device_register("platform-lcd", dev,
+ plcd->lcd = lcd_device_register(dev_name(dev), dev,
plcd, &platform_lcd_ops);
if (IS_ERR(plcd->lcd)) {
dev_err(dev, "cannot register lcd device\n");
}
platform_set_drvdata(pdev, plcd);
+ platform_lcd_set_power(plcd->lcd, FB_BLANK_NORMAL);
+
return 0;
err_mem:
struct pwm_bl_data *pb;
int ret;
- if (!data)
+ if (!data) {
+ dev_err(&pdev->dev, "failed to find platform data\n");
return -EINVAL;
+ }
if (data->init) {
ret = data->init(&pdev->dev);
pb = kzalloc(sizeof(*pb), GFP_KERNEL);
if (!pb) {
+ dev_err(&pdev->dev, "no memory for state\n");
ret = -ENOMEM;
goto err_alloc;
}
dev_err(&pdev->dev, "unable to request PWM for backlight\n");
ret = PTR_ERR(pb->pwm);
goto err_pwm;
- }
+ } else
+ dev_dbg(&pdev->dev, "got pwm for backlight\n");
bl = backlight_device_register(pdev->name, &pdev->dev,
pb, &pwm_backlight_ops);
MODULE_DESCRIPTION("PWM based Backlight Driver");
MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pwm-backlight");
+
#include <linux/proc_fs.h>
#include <linux/delay.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <linux/uaccess.h>
#include <asm/hardware/clps7111.h>
-#include <asm/arch/syspld.h>
+#include <mach/syspld.h>
struct fb_info *cfb;
--- /dev/null
+# conmakehash generated file
+promcon_tbl.c
if (!height || !width)
return;
+ if (sy < vc->vc_top && vc->vc_top == logo_lines)
+ vc->vc_top = 0;
+
/* Split blits that cross physical y_wrap boundary */
y_break = p->vrows - p->yscroll;
#include <asm/hardware.h>
#include <asm/parisc-device.h>
#include <asm/cacheflush.h>
+#include <asm/grfioctl.h>
#include "../sticore.h"
{
struct sti_cooked_rom *cooked;
struct sti_rom *raw = NULL;
+ unsigned long revno;
cooked = kmalloc(sizeof *cooked, GFP_KERNEL);
if (!cooked)
sti->graphics_id[1] = raw->graphics_id[1];
sti_dump_rom(raw);
-
+
+ /* check if the ROM routines in this card are compatible */
+ if (wordmode || sti->graphics_id[1] != 0x09A02587)
+ goto ok;
+
+ revno = (raw->revno[0] << 8) | raw->revno[1];
+
+ switch (sti->graphics_id[0]) {
+ case S9000_ID_HCRX:
+ /* HyperA or HyperB ? */
+ if (revno == 0x8408 || revno == 0x840b)
+ goto msg_not_supported;
+ break;
+ case CRT_ID_THUNDER:
+ if (revno == 0x8509)
+ goto msg_not_supported;
+ break;
+ case CRT_ID_THUNDER2:
+ if (revno == 0x850c)
+ goto msg_not_supported;
+ }
+ok:
return 1;
+msg_not_supported:
+ printk(KERN_ERR "Sorry, this GSC/STI card is not yet supported.\n");
+ printk(KERN_ERR "Please see http://parisc-linux.org/faq/"
+ "graphics-howto.html for more info.\n");
+ /* fall through */
out_err:
kfree(raw);
kfree(cooked);
#ifdef CONFIG_ARCH_SHARK
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
static int __devinit cyberpro_vl_probe(void)
{
#if defined(CONFIG_ARM)
# ifdef CONFIG_ARCH_CEIVA
-# include <asm/arch/hardware.h>
+# include <mach/hardware.h>
# define EPSON1355FB_BASE_PHYS (CEIVA_PHYS_SED1355)
# endif
}
prop = of_get_property(np, "d-cache-size", NULL);
- if (prop == NULL)
+ if (prop == NULL) {
+ of_node_put(np);
return -ENODEV;
+ }
/* Freescale PLRU requires 13/8 times the cache size to do a proper
displacement flush
coherence_data_size /= 8;
prop = of_get_property(np, "d-cache-line-size", NULL);
- if (prop == NULL)
+ if (prop == NULL) {
+ of_node_put(np);
return -ENODEV;
+ }
d_cache_line_size = *prop;
of_node_put(np);
static int ypan, ywrap;
static uint32_t pseudo_palette[16];
+static uint32_t gbe_cmap[256];
+static int gbe_turned_on; /* 0 turned off, 1 turned on */
static char *mode_option __initdata = NULL;
int i;
unsigned int val, x, y, vpixen_off;
+ gbe_turned_on = 0;
+
/* check if pixel counter is on */
val = gbe->vt_xy;
if (GET_GBE_FIELD(VT_XY, FREEZE, val) == 1)
}
if (i == 10000)
printk(KERN_ERR "gbefb: turn on DMA timed out\n");
+
+ gbe_turned_on = 1;
+}
+
+static void gbe_loadcmap(void)
+{
+ int i, j;
+
+ for (i = 0; i < 256; i++) {
+ for (j = 0; j < 1000 && gbe->cm_fifo >= 63; j++)
+ udelay(10);
+ if (j == 1000)
+ printk(KERN_ERR "gbefb: cmap FIFO timeout\n");
+
+ gbe->cmap[i] = gbe_cmap[i];
+ }
}
/*
switch (blank) {
case FB_BLANK_UNBLANK: /* unblank */
gbe_turn_on();
+ gbe_loadcmap();
break;
case FB_BLANK_NORMAL: /* blank */
gbe->gmap[i] = (i << 24) | (i << 16) | (i << 8);
/* Initialize the color map */
- for (i = 0; i < 256; i++) {
- int j;
-
- for (j = 0; j < 1000 && gbe->cm_fifo >= 63; j++)
- udelay(10);
- if (j == 1000)
- printk(KERN_ERR "gbefb: cmap FIFO timeout\n");
+ for (i = 0; i < 256; i++)
+ gbe_cmap[i] = (i << 8) | (i << 16) | (i << 24);
- gbe->cmap[i] = (i << 8) | (i << 16) | (i << 24);
- }
+ gbe_loadcmap();
return 0;
}
blue >>= 8;
if (info->var.bits_per_pixel <= 8) {
- /* wait for the color map FIFO to have a free entry */
- for (i = 0; i < 1000 && gbe->cm_fifo >= 63; i++)
- udelay(10);
- if (i == 1000) {
- printk(KERN_ERR "gbefb: cmap FIFO timeout\n");
- return 1;
+ gbe_cmap[regno] = (red << 24) | (green << 16) | (blue << 8);
+ if (gbe_turned_on) {
+ /* wait for the color map FIFO to have a free entry */
+ for (i = 0; i < 1000 && gbe->cm_fifo >= 63; i++)
+ udelay(10);
+ if (i == 1000) {
+ printk(KERN_ERR "gbefb: cmap FIFO timeout\n");
+ return 1;
+ }
+ gbe->cmap[regno] = gbe_cmap[regno];
}
- gbe->cmap[regno] = (red << 24) | (green << 16) | (blue << 8);
} else if (regno < 16) {
switch (info->var.bits_per_pixel) {
case 15:
#include <asm/pgtable.h>
#include <asm/io.h>
#include <asm/hd64461.h>
-#include <asm/cpu/dac.h>
+#include <cpu/dac.h>
#define WIDTH 640
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
-#include <asm/arch/imxfb.h>
+#include <mach/imxfb.h>
/*
* Complain if VAR is out of range.
MODULE_PARM_DESC(fh, "Startup horizontal frequency, 0-999kHz, 1000-INF Hz");
module_param(fv, int, 0);
MODULE_PARM_DESC(fv, "Startup vertical frequency, 0-INF Hz\n"
-"You should specify \"fv:max_monitor_vsync,fh:max_monitor_hsync,maxclk:max_monitor_dotclock\"\n");
+"You should specify \"fv:max_monitor_vsync,fh:max_monitor_hsync,maxclk:max_monitor_dotclock\"");
module_param(grayscale, int, 0);
MODULE_PARM_DESC(grayscale, "Sets display into grayscale. Works perfectly with paletized videomode (4, 8bpp), some limitations apply to 16, 24 and 32bpp videomodes (default=nograyscale)");
module_param(cross4MB, int, 0);
#include <linux/delay.h>
#include <linux/clk.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/omapfb.h>
-#include <asm/arch/blizzard.h>
+#include <mach/dma.h>
+#include <mach/omapfb.h>
+#include <mach/blizzard.h>
#include "dispc.h"
#include <linux/clk.h>
#include <linux/io.h>
-#include <asm/arch/sram.h>
-#include <asm/arch/omapfb.h>
-#include <asm/arch/board.h>
+#include <mach/sram.h>
+#include <mach/omapfb.h>
+#include <mach/board.h>
#include "dispc.h"
#include <linux/delay.h>
#include <linux/clk.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/omapfb.h>
-#include <asm/arch/hwa742.h>
+#include <mach/dma.h>
+#include <mach/omapfb.h>
+#include <mach/hwa742.h>
#define HWA742_REV_CODE_REG 0x0
#define HWA742_CONFIG_REG 0x2
#include <linux/platform_device.h>
#include <linux/i2c/tps65010.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/omapfb.h>
+#include <mach/gpio.h>
+#include <mach/omapfb.h>
#define MODULE_NAME "omapfb-lcd_h3"
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/arch/omapfb.h>
+#include <mach/omapfb.h>
static int h4_panel_init(struct lcd_panel *panel, struct omapfb_device *fbdev)
{
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/omapfb.h>
+#include <mach/fpga.h>
+#include <mach/omapfb.h>
static int innovator1510_panel_init(struct lcd_panel *panel,
struct omapfb_device *fbdev)
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/omapfb.h>
+#include <mach/gpio.h>
+#include <mach/omapfb.h>
#define MODULE_NAME "omapfb-lcd_h3"
#include <linux/module.h>
#include <linux/platform_device.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mux.h>
-#include <asm/arch/omapfb.h>
+#include <mach/gpio.h>
+#include <mach/mux.h>
+#include <mach/omapfb.h>
static int osk_panel_init(struct lcd_panel *panel, struct omapfb_device *fbdev)
{
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/arch/fpga.h>
-#include <asm/arch/omapfb.h>
+#include <mach/fpga.h>
+#include <mach/omapfb.h>
static int palmte_panel_init(struct lcd_panel *panel,
struct omapfb_device *fbdev)
#include <linux/module.h>
#include <linux/io.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/omapfb.h>
+#include <mach/gpio.h>
+#include <mach/omapfb.h>
static int palmtt_panel_init(struct lcd_panel *panel,
struct omapfb_device *fbdev)
#include <linux/platform_device.h>
#include <linux/io.h>
-#include <asm/arch/omapfb.h>
+#include <mach/omapfb.h>
static int palmz71_panel_init(struct lcd_panel *panel,
struct omapfb_device *fbdev)
#include <linux/delay.h>
#include <linux/io.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/omapfb.h>
-#include <asm/arch/mcbsp.h>
-#include <asm/arch/mux.h>
+#include <mach/gpio.h>
+#include <mach/omapfb.h>
+#include <mach/mcbsp.h>
+#include <mach/mux.h>
/*
* OMAP310 GPIO registers
#include <linux/vmalloc.h>
#include <linux/clk.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/omapfb.h>
+#include <mach/dma.h>
+#include <mach/omapfb.h>
#include <asm/mach-types.h>
#include <linux/mm.h>
#include <linux/uaccess.h>
-#include <asm/mach-types.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/omapfb.h>
+#include <mach/dma.h>
+#include <mach/omapfb.h>
#define MODULE_NAME "omapfb"
#include <linux/clk.h>
#include <linux/io.h>
-#include <asm/arch/omapfb.h>
+#include <mach/omapfb.h>
#include "dispc.h"
#include <linux/irq.h>
#include <linux/io.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/omapfb.h>
+#include <mach/dma.h>
+#include <mach/omapfb.h>
#include "lcdc.h"
#ifndef __PNX008_DUM_H__
#define __PNX008_DUM_H__
-#include <asm/arch/platform.h>
+#include <mach/platform.h>
#define PNX4008_DUMCONF_VA_BASE IO_ADDRESS(PNX4008_DUMCONF_BASE)
#define PNX4008_DUM_MAIN_VA_BASE IO_ADDRESS(PNX4008_DUM_MAINCFG_BASE)
#include <linux/dma-mapping.h>
#include <linux/clk.h>
#include <asm/uaccess.h>
-#include <asm/arch/gpio.h>
+#include <mach/gpio.h>
#include "sdum.h"
#include "fbcommon.h"
#ifdef CONFIG_SH_DREAMCAST
#include <asm/machvec.h>
-#include <asm/mach/sysasic.h>
+#include <mach-dreamcast/mach/sysasic.h>
#endif
#ifdef CONFIG_SH_DMA
#include <linux/pagemap.h>
-#include <asm/mach/dma.h>
+#include <mach/dma.h>
#include <asm/dma.h>
#endif
#ifdef CONFIG_SH_STORE_QUEUES
#include <linux/uaccess.h>
-#include <asm/cpu/sq.h>
+#include <cpu/sq.h>
#endif
#ifndef PCI_DEVICE_ID_NEC_NEON250
#include <linux/kthread.h>
#include <linux/freezer.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/div64.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/bitfield.h>
-#include <asm/arch/pxafb.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/bitfield.h>
+#include <mach/pxafb.h>
/*
* Complain if VAR is out of range.
#include <asm/div64.h>
#include <asm/mach/map.h>
-#include <asm/arch/regs-lcd.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/fb.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-gpio.h>
+#include <mach/fb.h>
#ifdef CONFIG_PM
#include <linux/pm.h>
/* Prepare PCI device */
rc = pci_enable_device(dev);
if (rc < 0) {
- dev_err(info->dev, "cannot enable PCI device\n");
+ dev_err(info->device, "cannot enable PCI device\n");
goto err_enable_device;
}
rc = pci_request_regions(dev, "s3fb");
if (rc < 0) {
- dev_err(info->dev, "cannot reserve framebuffer region\n");
+ dev_err(info->device, "cannot reserve framebuffer region\n");
goto err_request_regions;
}
info->screen_base = pci_iomap(dev, 0, 0);
if (! info->screen_base) {
rc = -ENOMEM;
- dev_err(info->dev, "iomap for framebuffer failed\n");
+ dev_err(info->device, "iomap for framebuffer failed\n");
goto err_iomap;
}
rc = fb_find_mode(&(info->var), info, mode_option, NULL, 0, NULL, 8);
if (! ((rc == 1) || (rc == 2))) {
rc = -EINVAL;
- dev_err(info->dev, "mode %s not found\n", mode_option);
+ dev_err(info->device, "mode %s not found\n", mode_option);
goto err_find_mode;
}
rc = fb_alloc_cmap(&info->cmap, 256, 0);
if (rc < 0) {
- dev_err(info->dev, "cannot allocate colormap\n");
+ dev_err(info->device, "cannot allocate colormap\n");
goto err_alloc_cmap;
}
rc = register_framebuffer(info);
if (rc < 0) {
- dev_err(info->dev, "cannot register framebuffer\n");
+ dev_err(info->device, "cannot register framebuffer\n");
goto err_reg_fb;
}
struct fb_info *info = pci_get_drvdata(dev);
struct s3fb_info *par = info->par;
- dev_info(info->dev, "suspend\n");
+ dev_info(info->device, "suspend\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
struct s3fb_info *par = info->par;
int err;
- dev_info(info->dev, "resume\n");
+ dev_info(info->device, "resume\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
if (err) {
mutex_unlock(&(par->open_lock));
release_console_sem();
- dev_err(info->dev, "error %d enabling device for resume\n", err);
+ dev_err(info->device, "error %d enabling device for resume\n", err);
return err;
}
pci_set_master(dev);
#include <linux/dma-mapping.h>
#include <linux/mutex.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
-#include <asm/arch/assabet.h>
-#include <asm/arch/shannon.h>
+#include <mach/assabet.h>
+#include <mach/shannon.h>
/*
* debugging?
rc = pci_enable_device(dev);
if (rc < 0) {
- dev_err(info->dev, "cannot enable PCI device\n");
+ dev_err(info->device, "cannot enable PCI device\n");
goto err_enable_device;
}
rc = pci_request_regions(dev, "vt8623fb");
if (rc < 0) {
- dev_err(info->dev, "cannot reserve framebuffer region\n");
+ dev_err(info->device, "cannot reserve framebuffer region\n");
goto err_request_regions;
}
info->screen_base = pci_iomap(dev, 0, 0);
if (! info->screen_base) {
rc = -ENOMEM;
- dev_err(info->dev, "iomap for framebuffer failed\n");
+ dev_err(info->device, "iomap for framebuffer failed\n");
goto err_iomap_1;
}
par->mmio_base = pci_iomap(dev, 1, 0);
if (! par->mmio_base) {
rc = -ENOMEM;
- dev_err(info->dev, "iomap for MMIO failed\n");
+ dev_err(info->device, "iomap for MMIO failed\n");
goto err_iomap_2;
}
if ((16 <= memsize1) && (memsize1 <= 64) && (memsize1 == memsize2))
info->screen_size = memsize1 << 20;
else {
- dev_err(info->dev, "memory size detection failed (%x %x), suppose 16 MB\n", memsize1, memsize2);
+ dev_err(info->device, "memory size detection failed (%x %x), suppose 16 MB\n", memsize1, memsize2);
info->screen_size = 16 << 20;
}
rc = fb_find_mode(&(info->var), info, mode_option, NULL, 0, NULL, 8);
if (! ((rc == 1) || (rc == 2))) {
rc = -EINVAL;
- dev_err(info->dev, "mode %s not found\n", mode_option);
+ dev_err(info->device, "mode %s not found\n", mode_option);
goto err_find_mode;
}
rc = fb_alloc_cmap(&info->cmap, 256, 0);
if (rc < 0) {
- dev_err(info->dev, "cannot allocate colormap\n");
+ dev_err(info->device, "cannot allocate colormap\n");
goto err_alloc_cmap;
}
rc = register_framebuffer(info);
if (rc < 0) {
- dev_err(info->dev, "cannot register framebugger\n");
+ dev_err(info->device, "cannot register framebugger\n");
goto err_reg_fb;
}
struct fb_info *info = pci_get_drvdata(dev);
struct vt8623fb_info *par = info->par;
- dev_info(info->dev, "suspend\n");
+ dev_info(info->device, "suspend\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
struct fb_info *info = pci_get_drvdata(dev);
struct vt8623fb_info *par = info->par;
- dev_info(info->dev, "resume\n");
+ dev_info(info->device, "resume\n");
acquire_console_sem();
mutex_lock(&(par->open_lock));
- if (par->ref_count == 0) {
- mutex_unlock(&(par->open_lock));
- release_console_sem();
- return 0;
- }
+ if (par->ref_count == 0)
+ goto fail;
pci_set_power_state(dev, PCI_D0);
pci_restore_state(dev);
vt8623fb_set_par(info);
fb_set_suspend(info, 0);
- mutex_unlock(&(par->open_lock));
fail:
+ mutex_unlock(&(par->open_lock));
release_console_sem();
return 0;
module will be called pc87413_wdt.
Most people will say N.
-
+
config 60XX_WDT
tristate "SBC-60XX Watchdog Timer"
depends on X86
tristate "MPC8xx Watchdog Timer"
depends on 8xx
-config 83xx_WDT
- tristate "MPC83xx Watchdog Timer"
- depends on PPC_83xx
+config 8xxx_WDT
+ tristate "MPC8xxx Platform Watchdog Timer"
+ depends on PPC_8xx || PPC_83xx || PPC_86xx
+ help
+ This driver is for a SoC level watchdog that exists on some
+ Freescale PowerPC processors. So far this driver supports:
+ - MPC8xx watchdogs
+ - MPC83xx watchdogs
+ - MPC86xx watchdogs
+
+ For BookE processors (MPC85xx) use the BOOKE_WDT driver instead.
config MV64X60_WDT
tristate "MV64X60 (Marvell Discovery) Watchdog Timer"
# MIPS Architecture
obj-$(CONFIG_INDYDOG) += indydog.o
-obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
+obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
# POWERPC Architecture
obj-$(CONFIG_8xx_WDT) += mpc8xx_wdt.o
obj-$(CONFIG_MPC5200_WDT) += mpc5200_wdt.o
-obj-$(CONFIG_83xx_WDT) += mpc83xx_wdt.o
+obj-$(CONFIG_8xxx_WDT) += mpc8xxx_wdt.o
obj-$(CONFIG_MV64X60_WDT) += mv64x60_wdt.o
obj-$(CONFIG_BOOKE_WDT) += booke_wdt.o
#include <linux/types.h> /* For standard types (like size_t) */
#include <linux/errno.h> /* For the -ENODEV/... values */
#include <linux/kernel.h> /* For printk/panic/... */
-#include <linux/miscdevice.h> /* For MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR) */
+#include <linux/miscdevice.h> /* For MODULE_ALIAS_MISCDEV
+ (WATCHDOG_MINOR) */
#include <linux/watchdog.h> /* For the watchdog specific items */
#include <linux/fs.h> /* For file operations */
#include <linux/ioport.h> /* For io-port access */
#include <linux/platform_device.h> /* For platform_driver framework */
#include <linux/init.h> /* For __init/__exit/... */
-
-#include <asm/uaccess.h> /* For copy_to_user/put_user/... */
-#include <asm/io.h> /* For inb/outb/... */
+#include <linux/uaccess.h> /* For copy_to_user/put_user/... */
+#include <linux/io.h> /* For inb/outb/... */
/* Module information */
#define DRV_NAME "acquirewdt"
#define PFX DRV_NAME ": "
#define WATCHDOG_NAME "Acquire WDT"
-#define WATCHDOG_HEARTBEAT 0 /* There is no way to see what the correct time-out period is */
+/* There is no way to see what the correct time-out period is */
+#define WATCHDOG_HEARTBEAT 0
/* internal variables */
-static struct platform_device *acq_platform_device; /* the watchdog platform device */
+/* the watchdog platform device */
+static struct platform_device *acq_platform_device;
static unsigned long acq_is_open;
static char expect_close;
/* module parameters */
-static int wdt_stop = 0x43; /* You must set this - there is no sane way to probe for this board. */
+/* You must set this - there is no sane way to probe for this board. */
+static int wdt_stop = 0x43;
module_param(wdt_stop, int, 0);
MODULE_PARM_DESC(wdt_stop, "Acquire WDT 'stop' io port (default 0x43)");
-static int wdt_start = 0x443; /* You must set this - there is no sane way to probe for this board. */
+/* You must set this - there is no sane way to probe for this board. */
+static int wdt_start = 0x443;
module_param(wdt_start, int, 0);
MODULE_PARM_DESC(wdt_start, "Acquire WDT 'start' io port (default 0x443)");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Watchdog Operations
* /dev/watchdog handling
*/
-static ssize_t acq_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t acq_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count) {
+ if (count) {
if (!nowayout) {
size_t i;
-
/* note: just in case someone wrote the magic character
- * five months ago... */
+ five months ago... */
expect_close = 0;
-
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got the
+ magic character */
for (i = 0; i != count; i++) {
char c;
if (get_user(c, buf + i))
expect_close = 42;
}
}
-
- /* Well, anyhow someone wrote to us, we should return that favour */
+ /* Well, anyhow someone wrote to us, we should
+ return that favour */
acq_keepalive();
}
return count;
}
-static int acq_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long acq_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int options, retval = -EINVAL;
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident =
- {
+ static struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = WATCHDOG_NAME,
};
- switch(cmd)
- {
+ switch (cmd) {
case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- acq_keepalive();
- return 0;
-
- case WDIOC_GETTIMEOUT:
- return put_user(WATCHDOG_HEARTBEAT, p);
+ return put_user(0, p);
case WDIOC_SETOPTIONS:
{
- if (get_user(options, p))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD)
- {
- acq_stop();
- retval = 0;
- }
-
- if (options & WDIOS_ENABLECARD)
- {
- acq_keepalive();
- retval = 0;
- }
-
- return retval;
+ if (get_user(options, p))
+ return -EFAULT;
+ if (options & WDIOS_DISABLECARD) {
+ acq_stop();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ acq_keepalive();
+ retval = 0;
+ }
+ return retval;
}
+ case WDIOC_KEEPALIVE:
+ acq_keepalive();
+ return 0;
+
+ case WDIOC_GETTIMEOUT:
+ return put_user(WATCHDOG_HEARTBEAT, p);
default:
- return -ENOTTY;
+ return -ENOTTY;
}
}
if (expect_close == 42) {
acq_stop();
} else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
acq_keepalive();
}
clear_bit(0, &acq_is_open);
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = acq_write,
- .ioctl = acq_ioctl,
+ .unlocked_ioctl = acq_ioctl,
.open = acq_open,
.release = acq_close,
};
if (wdt_stop != wdt_start) {
if (!request_region(wdt_stop, 1, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
- wdt_stop);
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n", wdt_stop);
ret = -EIO;
goto out;
}
}
if (!request_region(wdt_start, 1, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
+ printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
wdt_start);
ret = -EIO;
goto unreg_stop;
}
-
ret = misc_register(&acq_miscdev);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_regions;
}
-
- printk (KERN_INFO PFX "initialized. (nowayout=%d)\n",
- nowayout);
+ printk(KERN_INFO PFX "initialized. (nowayout=%d)\n", nowayout);
return 0;
-
unreg_regions:
release_region(wdt_start, 1);
unreg_stop:
static int __devexit acq_remove(struct platform_device *dev)
{
misc_deregister(&acq_miscdev);
- release_region(wdt_start,1);
- if(wdt_stop != wdt_start)
- release_region(wdt_stop,1);
+ release_region(wdt_start, 1);
+ if (wdt_stop != wdt_start)
+ release_region(wdt_stop, 1);
return 0;
}
{
int err;
- printk(KERN_INFO "WDT driver for Acquire single board computer initialising.\n");
+ printk(KERN_INFO
+ "WDT driver for Acquire single board computer initialising.\n");
err = platform_driver_register(&acquirewdt_driver);
if (err)
return err;
- acq_platform_device = platform_device_register_simple(DRV_NAME, -1, NULL, 0);
+ acq_platform_device = platform_device_register_simple(DRV_NAME,
+ -1, NULL, 0);
if (IS_ERR(acq_platform_device)) {
err = PTR_ERR(acq_platform_device);
goto unreg_platform_driver;
}
-
return 0;
unreg_platform_driver:
#include <linux/ioport.h>
#include <linux/platform_device.h>
#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define DRV_NAME "advantechwdt"
#define WATCHDOG_NAME "Advantech WDT"
#define WATCHDOG_TIMEOUT 60 /* 60 sec default timeout */
-static struct platform_device *advwdt_platform_device; /* the watchdog platform device */
+/* the watchdog platform device */
+static struct platform_device *advwdt_platform_device;
static unsigned long advwdt_is_open;
static char adv_expect_close;
static int timeout = WATCHDOG_TIMEOUT; /* in seconds */
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. 1<= timeout <=63, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ".");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. 1<= timeout <=63, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ".");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Watchdog Operations
*/
-static void
-advwdt_ping(void)
+static void advwdt_ping(void)
{
/* Write a watchdog value */
outb_p(timeout, wdt_start);
}
-static void
-advwdt_disable(void)
+static void advwdt_disable(void)
{
inb_p(wdt_stop);
}
-static int
-advwdt_set_heartbeat(int t)
+static int advwdt_set_heartbeat(int t)
{
- if ((t < 1) || (t > 63))
+ if (t < 1 || t > 63)
return -EINVAL;
-
timeout = t;
return 0;
}
* /dev/watchdog handling
*/
-static ssize_t
-advwdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t advwdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
for (i = 0; i != count; i++) {
char c;
- if (get_user(c, buf+i))
+ if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
adv_expect_close = 42;
return count;
}
-static int
-advwdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long advwdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int new_timeout;
void __user *argp = (void __user *)arg;
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof(ident)))
- return -EFAULT;
- break;
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- advwdt_ping();
- break;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, p))
- return -EFAULT;
- if (advwdt_set_heartbeat(new_timeout))
- return -EINVAL;
- advwdt_ping();
- /* Fall */
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
+ return put_user(0, p);
case WDIOC_SETOPTIONS:
{
- int options, retval = -EINVAL;
-
- if (get_user(options, p))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- advwdt_disable();
- retval = 0;
- }
+ int options, retval = -EINVAL;
- if (options & WDIOS_ENABLECARD) {
- advwdt_ping();
- retval = 0;
- }
-
- return retval;
+ if (get_user(options, p))
+ return -EFAULT;
+ if (options & WDIOS_DISABLECARD) {
+ advwdt_disable();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ advwdt_ping();
+ retval = 0;
+ }
+ return retval;
}
+ case WDIOC_KEEPALIVE:
+ advwdt_ping();
+ break;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if (advwdt_set_heartbeat(new_timeout))
+ return -EINVAL;
+ advwdt_ping();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
default:
- return -ENOTTY;
+ return -ENOTTY;
}
return 0;
}
-static int
-advwdt_open(struct inode *inode, struct file *file)
+static int advwdt_open(struct inode *inode, struct file *file)
{
if (test_and_set_bit(0, &advwdt_is_open))
return -EBUSY;
return nonseekable_open(inode, file);
}
-static int
-advwdt_close(struct inode *inode, struct file *file)
+static int advwdt_close(struct inode *inode, struct file *file)
{
if (adv_expect_close == 42) {
advwdt_disable();
} else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
advwdt_ping();
}
clear_bit(0, &advwdt_is_open);
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = advwdt_write,
- .ioctl = advwdt_ioctl,
+ .unlocked_ioctl = advwdt_ioctl,
.open = advwdt_open,
.release = advwdt_close,
};
* Init & exit routines
*/
-static int __devinit
-advwdt_probe(struct platform_device *dev)
+static int __devinit advwdt_probe(struct platform_device *dev)
{
int ret;
if (wdt_stop != wdt_start) {
if (!request_region(wdt_stop, 1, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
- wdt_stop);
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n",
+ wdt_stop);
ret = -EIO;
goto out;
}
}
if (!request_region(wdt_start, 1, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
- wdt_start);
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n",
+ wdt_start);
ret = -EIO;
goto unreg_stop;
}
/* Check that the heartbeat value is within it's range ; if not reset to the default */
if (advwdt_set_heartbeat(timeout)) {
advwdt_set_heartbeat(WATCHDOG_TIMEOUT);
- printk (KERN_INFO PFX "timeout value must be 1<=x<=63, using %d\n",
- timeout);
+ printk(KERN_INFO PFX
+ "timeout value must be 1<=x<=63, using %d\n", timeout);
}
ret = misc_register(&advwdt_miscdev);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_regions;
}
-
- printk (KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
+ printk(KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
-
out:
return ret;
unreg_regions:
goto out;
}
-static int __devexit
-advwdt_remove(struct platform_device *dev)
+static int __devexit advwdt_remove(struct platform_device *dev)
{
misc_deregister(&advwdt_miscdev);
- release_region(wdt_start,1);
- if(wdt_stop != wdt_start)
- release_region(wdt_stop,1);
+ release_region(wdt_start, 1);
+ if (wdt_stop != wdt_start)
+ release_region(wdt_stop, 1);
return 0;
}
-static void
-advwdt_shutdown(struct platform_device *dev)
+static void advwdt_shutdown(struct platform_device *dev)
{
/* Turn the WDT off if we have a soft shutdown */
advwdt_disable();
},
};
-static int __init
-advwdt_init(void)
+static int __init advwdt_init(void)
{
int err;
- printk(KERN_INFO "WDT driver for Advantech single board computer initialising.\n");
+ printk(KERN_INFO
+ "WDT driver for Advantech single board computer initialising.\n");
err = platform_driver_register(&advwdt_driver);
if (err)
return err;
- advwdt_platform_device = platform_device_register_simple(DRV_NAME, -1, NULL, 0);
+ advwdt_platform_device = platform_device_register_simple(DRV_NAME,
+ -1, NULL, 0);
if (IS_ERR(advwdt_platform_device)) {
err = PTR_ERR(advwdt_platform_device);
goto unreg_platform_driver;
return err;
}
-static void __exit
-advwdt_exit(void)
+static void __exit advwdt_exit(void)
{
platform_device_unregister(advwdt_platform_device);
platform_driver_unregister(&advwdt_driver);
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/pci.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#define WATCHDOG_NAME "ALi_M1535"
#define PFX WATCHDOG_NAME ": "
static unsigned long ali_is_open;
static char ali_expect_release;
static struct pci_dev *ali_pci;
-static u32 ali_timeout_bits; /* stores the computed timeout */
+static u32 ali_timeout_bits; /* stores the computed timeout */
static DEFINE_SPINLOCK(ali_lock); /* Guards the hardware */
/* module parameters */
static int timeout = WATCHDOG_TIMEOUT;
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (0<timeout<18000, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (0 < timeout < 18000, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* ali_start - start watchdog countdown
static int ali_settimer(int t)
{
- if(t < 0)
+ if (t < 0)
return -EINVAL;
- else if(t < 60)
+ else if (t < 60)
ali_timeout_bits = t|(1<<6);
- else if(t < 3600)
+ else if (t < 3600)
ali_timeout_bits = (t/60)|(1<<7);
- else if(t < 18000)
+ else if (t < 18000)
ali_timeout_bits = (t/300)|(1<<6)|(1<<7);
- else return -EINVAL;
+ else
+ return -EINVAL;
timeout = t;
return 0;
*/
static ssize_t ali_write(struct file *file, const char __user *data,
- size_t len, loff_t * ppos)
+ size_t len, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
if (len) {
if (!nowayout) {
size_t i;
- /* note: just in case someone wrote the magic character
- * five months ago... */
+ /* note: just in case someone wrote the
+ magic character five months ago... */
ali_expect_release = 0;
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got
+ the magic character */
for (i = 0; i != len; i++) {
char c;
- if(get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
ali_expect_release = 42;
/*
* ali_ioctl - handle watchdog ioctls
- * @inode: VFS inode
* @file: VFS file pointer
* @cmd: ioctl number
* @arg: arguments to the ioctl
* we want an extension to enable irq ack monitoring and the like
*/
-static int ali_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long ali_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
};
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof (ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- ali_keepalive();
- return 0;
-
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if (get_user (new_options, p))
- return -EFAULT;
-
- if (new_options & WDIOS_DISABLECARD) {
- ali_stop();
- retval = 0;
- }
-
- if (new_options & WDIOS_ENABLECARD) {
- ali_start();
- retval = 0;
- }
-
- return retval;
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ {
+ int new_options, retval = -EINVAL;
+
+ if (get_user(new_options, p))
+ return -EFAULT;
+ if (new_options & WDIOS_DISABLECARD) {
+ ali_stop();
+ retval = 0;
}
-
- case WDIOC_SETTIMEOUT:
- {
- int new_timeout;
-
- if (get_user(new_timeout, p))
- return -EFAULT;
-
- if (ali_settimer(new_timeout))
- return -EINVAL;
-
- ali_keepalive();
- /* Fall */
+ if (new_options & WDIOS_ENABLECARD) {
+ ali_start();
+ retval = 0;
}
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
- default:
- return -ENOTTY;
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ ali_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if (ali_settimer(new_timeout))
+ return -EINVAL;
+ ali_keepalive();
+ /* Fall */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
/*
* Shut off the timer.
*/
- if (ali_expect_release == 42) {
+ if (ali_expect_release == 42)
ali_stop();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
ali_keepalive();
}
clear_bit(0, &ali_is_open);
*/
-static int ali_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int ali_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the WDT off */
- ali_stop();
- }
-
+ if (code == SYS_DOWN || code == SYS_HALT)
+ ali_stop(); /* Turn the WDT off */
return NOTIFY_DONE;
}
/* Check for the a 7101 PMU */
pdev = pci_get_device(PCI_VENDOR_ID_AL, 0x7101, NULL);
- if(pdev == NULL)
+ if (pdev == NULL)
return -ENODEV;
- if(pci_enable_device(pdev)) {
+ if (pci_enable_device(pdev)) {
pci_dev_put(pdev);
return -EIO;
}
*/
pci_read_config_dword(pdev, 0xCC, &wdog);
- wdog &= ~0x3F; /* Timer bits */
- wdog &= ~((1<<27)|(1<<26)|(1<<25)|(1<<24)); /* Issued events */
- wdog &= ~((1<<16)|(1<<13)|(1<<12)|(1<<11)|(1<<10)|(1<<9)); /* No monitor bits */
+ /* Timer bits */
+ wdog &= ~0x3F;
+ /* Issued events */
+ wdog &= ~((1<<27)|(1<<26)|(1<<25)|(1<<24));
+ /* No monitor bits */
+ wdog &= ~((1<<16)|(1<<13)|(1<<12)|(1<<11)|(1<<10)|(1<<9));
pci_write_config_dword(pdev, 0xCC, wdog);
*/
static const struct file_operations ali_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = ali_write,
- .ioctl = ali_ioctl,
- .open = ali_open,
- .release = ali_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = ali_write,
+ .unlocked_ioctl = ali_ioctl,
+ .open = ali_open,
+ .release = ali_release,
};
static struct miscdevice ali_miscdev = {
int ret;
/* Check whether or not the hardware watchdog is there */
- if (ali_find_watchdog() != 0) {
+ if (ali_find_watchdog() != 0)
return -ENODEV;
- }
- /* Check that the timeout value is within it's range ; if not reset to the default */
+ /* Check that the timeout value is within it's range;
+ if not reset to the default */
if (timeout < 1 || timeout >= 18000) {
timeout = WATCHDOG_TIMEOUT;
- printk(KERN_INFO PFX "timeout value must be 0<timeout<18000, using %d\n",
- timeout);
+ printk(KERN_INFO PFX
+ "timeout value must be 0 < timeout < 18000, using %d\n",
+ timeout);
}
/* Calculate the watchdog's timeout */
ret = register_reboot_notifier(&ali_notifier);
if (ret != 0) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
goto out;
}
ret = misc_register(&ali_miscdev);
if (ret != 0) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_reboot;
}
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define OUR_NAME "alim7101_wdt"
*/
#define WATCHDOG_TIMEOUT 30 /* 30 sec default timeout */
-static int timeout = WATCHDOG_TIMEOUT; /* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+/* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+static int timeout = WATCHDOG_TIMEOUT;
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=3600, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1<=timeout<=3600, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
-static int use_gpio = 0; /* Use the pic (for a1d revision alim7101) */
+static int use_gpio; /* Use the pic (for a1d revision alim7101) */
module_param(use_gpio, int, 0);
-MODULE_PARM_DESC(use_gpio, "Use the gpio watchdog. (required by old cobalt boards)");
+MODULE_PARM_DESC(use_gpio,
+ "Use the gpio watchdog (required by old cobalt boards).");
static void wdt_timer_ping(unsigned long);
static DEFINE_TIMER(timer, wdt_timer_ping, 0, 1);
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
- __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Whack the dog
/* If we got a heartbeat pulse within the WDT_US_INTERVAL
* we agree to ping the WDT
*/
- char tmp;
+ char tmp;
- if(time_before(jiffies, next_heartbeat))
- {
+ if (time_before(jiffies, next_heartbeat)) {
/* Ping the WDT (this is actually a disarm/arm sequence) */
pci_read_config_byte(alim7101_pmu, 0x92, &tmp);
- pci_write_config_byte(alim7101_pmu, ALI_7101_WDT, (tmp & ~ALI_WDT_ARM));
- pci_write_config_byte(alim7101_pmu, ALI_7101_WDT, (tmp | ALI_WDT_ARM));
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_WDT, (tmp & ~ALI_WDT_ARM));
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_WDT, (tmp | ALI_WDT_ARM));
if (use_gpio) {
- pci_read_config_byte(alim7101_pmu, ALI_7101_GPIO_O, &tmp);
- pci_write_config_byte(alim7101_pmu, ALI_7101_GPIO_O, tmp
- | 0x20);
- pci_write_config_byte(alim7101_pmu, ALI_7101_GPIO_O, tmp
- & ~0x20);
+ pci_read_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, &tmp);
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, tmp | 0x20);
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, tmp & ~0x20);
}
} else {
- printk(KERN_WARNING PFX "Heartbeat lost! Will not ping the watchdog\n");
+ printk(KERN_WARNING PFX
+ "Heartbeat lost! Will not ping the watchdog\n");
}
/* Re-set the timer interval */
mod_timer(&timer, jiffies + WDT_INTERVAL);
static void wdt_change(int writeval)
{
- char tmp;
+ char tmp;
pci_read_config_byte(alim7101_pmu, ALI_7101_WDT, &tmp);
if (writeval == WDT_ENABLE) {
- pci_write_config_byte(alim7101_pmu, ALI_7101_WDT, (tmp | ALI_WDT_ARM));
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_WDT, (tmp | ALI_WDT_ARM));
if (use_gpio) {
- pci_read_config_byte(alim7101_pmu, ALI_7101_GPIO_O, &tmp);
- pci_write_config_byte(alim7101_pmu, ALI_7101_GPIO_O, tmp & ~0x20);
+ pci_read_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, &tmp);
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, tmp & ~0x20);
}
} else {
- pci_write_config_byte(alim7101_pmu, ALI_7101_WDT, (tmp & ~ALI_WDT_ARM));
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_WDT, (tmp & ~ALI_WDT_ARM));
if (use_gpio) {
- pci_read_config_byte(alim7101_pmu, ALI_7101_GPIO_O, &tmp);
- pci_write_config_byte(alim7101_pmu, ALI_7101_GPIO_O, tmp | 0x20);
+ pci_read_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, &tmp);
+ pci_write_config_byte(alim7101_pmu,
+ ALI_7101_GPIO_O, tmp | 0x20);
}
}
}
* /dev/watchdog handling
*/
-static ssize_t fop_write(struct file * file, const char __user * buf, size_t count, loff_t * ppos)
+static ssize_t fop_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count) {
+ if (count) {
if (!nowayout) {
size_t ofs;
/* now scan */
for (ofs = 0; ofs != count; ofs++) {
char c;
- if (get_user(c, buf+ofs))
+ if (get_user(c, buf + ofs))
return -EFAULT;
if (c == 'V')
wdt_expect_close = 42;
return count;
}
-static int fop_open(struct inode * inode, struct file * file)
+static int fop_open(struct inode *inode, struct file *file)
{
/* Just in case we're already talking to someone... */
- if(test_and_set_bit(0, &wdt_is_open))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
/* Good, fire up the show */
wdt_startup();
return nonseekable_open(inode, file);
}
-static int fop_close(struct inode * inode, struct file * file)
+static int fop_close(struct inode *inode, struct file *file)
{
- if(wdt_expect_close == 42)
+ if (wdt_expect_close == 42)
wdt_turnoff();
else {
/* wim: shouldn't there be a: del_timer(&timer); */
- printk(KERN_CRIT PFX "device file closed unexpectedly. Will not stop the WDT!\n");
+ printk(KERN_CRIT PFX
+ "device file closed unexpectedly. Will not stop the WDT!\n");
}
clear_bit(0, &wdt_is_open);
wdt_expect_close = 0;
return 0;
}
-static int fop_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+static long fop_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident =
- {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "ALiM7101",
};
- switch(cmd)
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
{
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if(get_user(new_options, p))
- return -EFAULT;
-
- if(new_options & WDIOS_DISABLECARD) {
- wdt_turnoff();
- retval = 0;
- }
+ int new_options, retval = -EINVAL;
- if(new_options & WDIOS_ENABLECARD) {
- wdt_startup();
- retval = 0;
- }
-
- return retval;
+ if (get_user(new_options, p))
+ return -EFAULT;
+ if (new_options & WDIOS_DISABLECARD) {
+ wdt_turnoff();
+ retval = 0;
}
- case WDIOC_SETTIMEOUT:
- {
- int new_timeout;
-
- if(get_user(new_timeout, p))
- return -EFAULT;
-
- if(new_timeout < 1 || new_timeout > 3600) /* arbitrary upper limit */
- return -EINVAL;
-
- timeout = new_timeout;
- wdt_keepalive();
- /* Fall through */
+ if (new_options & WDIOS_ENABLECARD) {
+ wdt_startup();
+ retval = 0;
}
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
- default:
- return -ENOTTY;
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
+
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ /* arbitrary upper limit */
+ if (new_timeout < 1 || new_timeout > 3600)
+ return -EINVAL;
+ timeout = new_timeout;
+ wdt_keepalive();
+ /* Fall through */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
static const struct file_operations wdt_fops = {
- .owner= THIS_MODULE,
- .llseek= no_llseek,
- .write= fop_write,
- .open= fop_open,
- .release= fop_close,
- .ioctl= fop_ioctl,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = fop_write,
+ .open = fop_open,
+ .release = fop_close,
+ .unlocked_ioctl = fop_ioctl,
};
static struct miscdevice wdt_miscdev = {
- .minor=WATCHDOG_MINOR,
- .name="watchdog",
- .fops=&wdt_fops,
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &wdt_fops,
};
/*
* Notifier for system down
*/
-static int wdt_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int wdt_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_turnoff();
- if (code==SYS_RESTART) {
+ if (code == SYS_RESTART) {
/*
- * Cobalt devices have no way of rebooting themselves other than
- * getting the watchdog to pull reset, so we restart the watchdog on
- * reboot with no heartbeat
+ * Cobalt devices have no way of rebooting themselves other
+ * than getting the watchdog to pull reset, so we restart the
+ * watchdog on reboot with no heartbeat
*/
wdt_change(WDT_ENABLE);
printk(KERN_INFO PFX "Watchdog timer is now enabled with no heartbeat - should reboot in ~1 second.\n");
* turn the timebomb registers off.
*/
-static struct notifier_block wdt_notifier=
-{
+static struct notifier_block wdt_notifier = {
.notifier_call = wdt_notify_sys,
};
ali1543_south = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533,
NULL);
if (!ali1543_south) {
- printk(KERN_INFO PFX "ALi 1543 South-Bridge not present - WDT not set\n");
+ printk(KERN_INFO PFX
+ "ALi 1543 South-Bridge not present - WDT not set\n");
goto err_out;
}
pci_read_config_byte(ali1543_south, 0x5e, &tmp);
if (!use_gpio) {
printk(KERN_INFO PFX "Detected old alim7101 revision 'a1d'. If this is a cobalt board, set the 'use_gpio' module parameter.\n");
goto err_out;
- }
+ }
nowayout = 1;
} else if ((tmp & 0x1e) != 0x12 && (tmp & 0x1e) != 0x00) {
printk(KERN_INFO PFX "ALi 1543 South-Bridge does not have the correct revision number (???1001?) - WDT not set\n");
goto err_out;
}
- if(timeout < 1 || timeout > 3600) /* arbitrary upper limit */
- {
+ if (timeout < 1 || timeout > 3600) {
+ /* arbitrary upper limit */
timeout = WATCHDOG_TIMEOUT;
- printk(KERN_INFO PFX "timeout value must be 1<=x<=3600, using %d\n",
- timeout);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= x <= 3600, using %d\n",
+ timeout);
}
rc = register_reboot_notifier(&wdt_notifier);
if (rc) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out;
}
goto err_out_reboot;
}
- if (nowayout) {
+ if (nowayout)
__module_get(THIS_MODULE);
- }
printk(KERN_INFO PFX "WDT driver for ALi M7101 initialised. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
u32 prescale;
};
-static struct semaphore open_semaphore;
+static unsigned long wdt_is_open;
+static spinlock_t wdt_lock;
static unsigned expect_close;
/* XXX currently fixed, allows max margin ~68.72 secs */
u32 change;
change = new_margin * (ar7_vbus_freq() / prescale_value);
- if (change < 1) change = 1;
- if (change > 0xffff) change = 0xffff;
+ if (change < 1)
+ change = 1;
+ if (change > 0xffff)
+ change = 0xffff;
ar7_wdt_change(change);
margin = change * prescale_value / ar7_vbus_freq();
printk(KERN_INFO DRVNAME
static int ar7_wdt_open(struct inode *inode, struct file *file)
{
/* only allow one at a time */
- if (down_trylock(&open_semaphore))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
ar7_wdt_enable_wdt();
expect_close = 0;
"will not disable the watchdog timer\n");
else if (!nowayout)
ar7_wdt_disable_wdt();
-
- up(&open_semaphore);
-
+ clear_bit(0, &wdt_is_open);
return 0;
}
}
static struct notifier_block ar7_wdt_notifier = {
- .notifier_call = ar7_wdt_notify_sys
+ .notifier_call = ar7_wdt_notify_sys,
};
static ssize_t ar7_wdt_write(struct file *file, const char *data,
if (len) {
size_t i;
+ spin_lock(&wdt_lock);
ar7_wdt_kick(1);
+ spin_unlock(&wdt_lock);
expect_close = 0;
for (i = 0; i < len; ++i) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 1;
return len;
}
-static int ar7_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long ar7_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
static struct watchdog_info ident = {
.identity = LONGNAME,
int new_margin;
switch (cmd) {
- default:
- return -ENOTTY;
case WDIOC_GETSUPPORT:
if (copy_to_user((struct watchdog_info *)arg, &ident,
sizeof(ident)))
if (new_margin < 1)
return -EINVAL;
+ spin_lock(&wdt_lock);
ar7_wdt_update_margin(new_margin);
ar7_wdt_kick(1);
+ spin_unlock(&wdt_lock);
case WDIOC_GETTIMEOUT:
if (put_user(margin, (int *)arg))
return -EFAULT;
return 0;
+ default:
+ return -ENOTTY;
}
}
static const struct file_operations ar7_wdt_fops = {
.owner = THIS_MODULE,
.write = ar7_wdt_write,
- .ioctl = ar7_wdt_ioctl,
+ .unlocked_ioctl = ar7_wdt_ioctl,
.open = ar7_wdt_open,
.release = ar7_wdt_release,
};
{
int rc;
+ spin_lock_init(&wdt_lock);
+
ar7_wdt_get_regs();
if (!request_mem_region(ar7_regs_wdt, sizeof(struct ar7_wdt),
ar7_wdt_prescale(prescale_value);
ar7_wdt_update_margin(margin);
- sema_init(&open_semaphore, 1);
-
rc = register_reboot_notifier(&ar7_wdt_notifier);
if (rc) {
printk(KERN_ERR DRVNAME
/*
* Handle commands from user-space.
*/
-static int at32_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long at32_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int ret = -ENOTTY;
int time;
int __user *p = argp;
switch (cmd) {
- case WDIOC_KEEPALIVE:
- at32_wdt_pat();
- ret = 0;
- break;
case WDIOC_GETSUPPORT:
ret = copy_to_user(argp, &at32_wdt_info,
sizeof(at32_wdt_info)) ? -EFAULT : 0;
break;
- case WDIOC_SETTIMEOUT:
- ret = get_user(time, p);
- if (ret)
- break;
- ret = at32_wdt_settimeout(time);
- if (ret)
- break;
- /* Enable new time value */
- at32_wdt_start();
- /* fall through */
- case WDIOC_GETTIMEOUT:
- ret = put_user(wdt->timeout, p);
- break;
case WDIOC_GETSTATUS:
ret = put_user(0, p);
break;
at32_wdt_start();
ret = 0;
break;
+ case WDIOC_KEEPALIVE:
+ at32_wdt_pat();
+ ret = 0;
+ break;
+ case WDIOC_SETTIMEOUT:
+ ret = get_user(time, p);
+ if (ret)
+ break;
+ ret = at32_wdt_settimeout(time);
+ if (ret)
+ break;
+ /* Enable new time value */
+ at32_wdt_start();
+ /* fall through */
+ case WDIOC_GETTIMEOUT:
+ ret = put_user(wdt->timeout, p);
+ break;
}
return ret;
*/
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_release = 42;
static const struct file_operations at32_wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = at32_wdt_ioctl,
+ .unlocked_ioctl = at32_wdt_ioctl,
.open = at32_wdt_open,
.release = at32_wdt_close,
.write = at32_wdt_write,
wdt = NULL;
platform_set_drvdata(pdev, NULL);
}
-
return 0;
}
#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/watchdog.h>
-#include <asm/uaccess.h>
-#include <asm/arch/at91_st.h>
-
+#include <linux/uaccess.h>
+#include <mach/at91_st.h>
#define WDT_DEFAULT_TIME 5 /* seconds */
#define WDT_MAX_TIME 256 /* seconds */
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(wdt_time, int, 0);
-MODULE_PARM_DESC(wdt_time, "Watchdog time in seconds. (default="__MODULE_STRING(WDT_DEFAULT_TIME) ")");
+MODULE_PARM_DESC(wdt_time, "Watchdog time in seconds. (default="
+ __MODULE_STRING(WDT_DEFAULT_TIME) ")");
#ifdef CONFIG_WATCHDOG_NOWAYOUT
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#endif
/*
* Disable the watchdog.
*/
-static void inline at91_wdt_stop(void)
+static inline void at91_wdt_stop(void)
{
at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN);
}
/*
* Enable and reset the watchdog.
*/
-static void inline at91_wdt_start(void)
+static inline void at91_wdt_start(void)
{
- at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN | (((65536 * wdt_time) >> 8) & AT91_ST_WDV));
+ at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN |
+ (((65536 * wdt_time) >> 8) & AT91_ST_WDV));
at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
}
/*
* Reload the watchdog timer. (ie, pat the watchdog)
*/
-static void inline at91_wdt_reload(void)
+static inline void at91_wdt_reload(void)
{
at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
}
*/
static int at91_wdt_close(struct inode *inode, struct file *file)
{
+ /* Disable the watchdog when file is closed */
if (!nowayout)
- at91_wdt_stop(); /* Disable the watchdog when file is closed */
+ at91_wdt_stop();
clear_bit(0, &at91wdt_busy);
return 0;
if ((new_time <= 0) || (new_time > WDT_MAX_TIME))
return -EINVAL;
- /* Set new watchdog time. It will be used when at91_wdt_start() is called. */
+ /* Set new watchdog time. It will be used when
+ at91_wdt_start() is called. */
wdt_time = new_time;
return 0;
}
/*
* Handle commands from user-space.
*/
-static int at91_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long at91_wdt_ioct(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_value;
- switch(cmd) {
- case WDIOC_KEEPALIVE:
- at91_wdt_reload(); /* pat the watchdog */
- return 0;
-
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &at91_wdt_info, sizeof(at91_wdt_info)) ? -EFAULT : 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_value, p))
- return -EFAULT;
-
- if (at91_wdt_settimeout(new_value))
- return -EINVAL;
-
- /* Enable new time value */
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &at91_wdt_info,
+ sizeof(at91_wdt_info)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ if (get_user(new_value, p))
+ return -EFAULT;
+ if (new_value & WDIOS_DISABLECARD)
+ at91_wdt_stop();
+ if (new_value & WDIOS_ENABLECARD)
at91_wdt_start();
-
- /* Return current value */
- return put_user(wdt_time, p);
-
- case WDIOC_GETTIMEOUT:
- return put_user(wdt_time, p);
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_SETOPTIONS:
- if (get_user(new_value, p))
- return -EFAULT;
-
- if (new_value & WDIOS_DISABLECARD)
- at91_wdt_stop();
- if (new_value & WDIOS_ENABLECARD)
- at91_wdt_start();
- return 0;
-
- default:
- return -ENOTTY;
+ return 0;
+ case WDIOC_KEEPALIVE:
+ at91_wdt_reload(); /* pat the watchdog */
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_value, p))
+ return -EFAULT;
+ if (at91_wdt_settimeout(new_value))
+ return -EINVAL;
+ /* Enable new time value */
+ at91_wdt_start();
+ /* Return current value */
+ return put_user(wdt_time, p);
+ case WDIOC_GETTIMEOUT:
+ return put_user(wdt_time, p);
+ default:
+ return -ENOTTY;
}
}
/*
* Pat the watchdog whenever device is written to.
*/
-static ssize_t at91_wdt_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t at91_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
at91_wdt_reload(); /* pat the watchdog */
return len;
static const struct file_operations at91wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = at91_wdt_ioctl,
+ .unlocked_ioctl = at91_wdt_ioctl,
.open = at91_wdt_open,
.release = at91_wdt_close,
.write = at91_wdt_write,
if (res)
return res;
- printk("AT91 Watchdog Timer enabled (%d seconds%s)\n", wdt_time, nowayout ? ", nowayout" : "");
+ printk(KERN_INFO "AT91 Watchdog Timer enabled (%d seconds%s)\n",
+ wdt_time, nowayout ? ", nowayout" : "");
return 0;
}
static int __init at91_wdt_init(void)
{
- /* Check that the heartbeat value is within range; if not reset to the default */
+ /* Check that the heartbeat value is within range;
+ if not reset to the default */
if (at91_wdt_settimeout(wdt_time)) {
at91_wdt_settimeout(WDT_DEFAULT_TIME);
pr_info("at91_wdt: wdt_time value must be 1 <= wdt_time <= 256, using %d\n", wdt_time);
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/uaccess.h>
#include <asm/blackfin.h>
-#include <asm/uaccess.h>
#define stamp(fmt, args...) pr_debug("%s:%i: " fmt "\n", __func__, __LINE__, ## args)
#define stampit() stamp("here i am")
int run = bfin_wdt_running();
bfin_wdt_stop();
bfin_write_WDOG_CNT(cnt);
- if (run) bfin_wdt_start();
+ if (run)
+ bfin_wdt_start();
}
spin_unlock_irqrestore(&bfin_wdt_spinlock, flags);
{
stampit();
- if (expect_close == 42) {
+ if (expect_close == 42)
bfin_wdt_stop();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
bfin_wdt_keepalive();
}
-
expect_close = 0;
clear_bit(0, &open_check);
-
return 0;
}
* Pings the watchdog on write.
*/
static ssize_t bfin_wdt_write(struct file *file, const char __user *data,
- size_t len, loff_t *ppos)
+ size_t len, loff_t *ppos)
{
stampit();
/**
* bfin_wdt_ioctl - Query Device
- * @inode: inode of device
* @file: file handle of device
* @cmd: watchdog command
* @arg: argument
* Query basic information from the device or ping it, as outlined by the
* watchdog API.
*/
-static int bfin_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long bfin_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
stampit();
switch (cmd) {
- default:
- return -ENOTTY;
-
- case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &bfin_wdt_info, sizeof(bfin_wdt_info)))
- return -EFAULT;
- else
- return 0;
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(!!(_bfin_swrst & SWRST_RESET_WDOG), p);
-
- case WDIOC_KEEPALIVE:
- bfin_wdt_keepalive();
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &bfin_wdt_info, sizeof(bfin_wdt_info)))
+ return -EFAULT;
+ else
return 0;
-
- case WDIOC_SETTIMEOUT: {
- int new_timeout;
-
- if (get_user(new_timeout, p))
- return -EFAULT;
-
- if (bfin_wdt_set_timeout(new_timeout))
- return -EINVAL;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(!!(_bfin_swrst & SWRST_RESET_WDOG), p);
+ case WDIOC_SETOPTIONS: {
+ unsigned long flags;
+ int options, ret = -EINVAL;
+
+ if (get_user(options, p))
+ return -EFAULT;
+
+ spin_lock_irqsave(&bfin_wdt_spinlock, flags);
+ if (options & WDIOS_DISABLECARD) {
+ bfin_wdt_stop();
+ ret = 0;
}
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
- case WDIOC_SETOPTIONS: {
- unsigned long flags;
- int options, ret = -EINVAL;
-
- if (get_user(options, p))
- return -EFAULT;
-
- spin_lock_irqsave(&bfin_wdt_spinlock, flags);
-
- if (options & WDIOS_DISABLECARD) {
- bfin_wdt_stop();
- ret = 0;
- }
-
- if (options & WDIOS_ENABLECARD) {
- bfin_wdt_start();
- ret = 0;
- }
-
- spin_unlock_irqrestore(&bfin_wdt_spinlock, flags);
-
- return ret;
+ if (options & WDIOS_ENABLECARD) {
+ bfin_wdt_start();
+ ret = 0;
}
+ spin_unlock_irqrestore(&bfin_wdt_spinlock, flags);
+ return ret;
+ }
+ case WDIOC_KEEPALIVE:
+ bfin_wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT: {
+ int new_timeout;
+
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if (bfin_wdt_set_timeout(new_timeout))
+ return -EINVAL;
+ }
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
* Handles specific events, such as turning off the watchdog during a
* shutdown event.
*/
-static int bfin_wdt_notify_sys(struct notifier_block *this, unsigned long code,
- void *unused)
+static int bfin_wdt_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
stampit();
#endif
static const struct file_operations bfin_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = bfin_wdt_write,
- .ioctl = bfin_wdt_ioctl,
- .open = bfin_wdt_open,
- .release = bfin_wdt_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = bfin_wdt_write,
+ .unlocked_ioctl = bfin_wdt_ioctl,
+ .open = bfin_wdt_open,
+ .release = bfin_wdt_release,
};
static struct miscdevice bfin_wdt_miscdev = {
static struct watchdog_info bfin_wdt_info = {
.identity = "Blackfin Watchdog",
.options = WDIOF_SETTIMEOUT |
- WDIOF_KEEPALIVEPING |
- WDIOF_MAGICCLOSE,
+ WDIOF_KEEPALIVEPING |
+ WDIOF_MAGICCLOSE,
};
static struct notifier_block bfin_wdt_notifier = {
ret = register_reboot_notifier(&bfin_wdt_notifier);
if (ret) {
- pr_devinit(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n", ret);
+ pr_devinit(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
return ret;
}
ret = misc_register(&bfin_wdt_miscdev);
if (ret) {
- pr_devinit(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ pr_devinit(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
unregister_reboot_notifier(&bfin_wdt_notifier);
return ret;
}
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
module_param(timeout, uint, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=((2^32)/SCLK), default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1<=timeout<=((2^32)/SCLK), default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#include <linux/miscdevice.h>
#include <linux/notifier.h>
#include <linux/watchdog.h>
+#include <linux/uaccess.h>
#include <asm/reg_booke.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
/* If the kernel parameter wdt=1, the watchdog will be enabled at boot.
*/
#ifdef CONFIG_FSL_BOOKE
-#define WDT_PERIOD_DEFAULT 63 /* Ex. wdt_period=28 bus=333Mhz , reset=~40sec */
+#define WDT_PERIOD_DEFAULT 63 /* Ex. wdt_period=28 bus=333Mhz,reset=~40sec */
#else
#define WDT_PERIOD_DEFAULT 3 /* Refer to the PPC40x and PPC4xx manuals */
#endif /* for timing information */
.identity = "PowerPC Book-E Watchdog",
};
-static int booke_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long booke_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
u32 tmp = 0;
u32 __user *p = (u32 __user *)arg;
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user((struct watchdog_info __user *)arg, &ident,
- sizeof(struct watchdog_info)))
+ if (copy_to_user(arg, &ident, sizeof(struct watchdog_info)))
return -EFAULT;
case WDIOC_GETSTATUS:
return put_user(ident.options, p);
tmp = mfspr(SPRN_TSR) & TSR_WRS(3);
/* returns 1 if last reset was caused by the WDT */
return (tmp ? 1 : 0);
- case WDIOC_KEEPALIVE:
- booke_wdt_ping();
- return 0;
- case WDIOC_SETTIMEOUT:
- if (get_user(booke_wdt_period, p))
- return -EFAULT;
- mtspr(SPRN_TCR, (mfspr(SPRN_TCR)&~WDTP(0))|WDTP(booke_wdt_period));
- return 0;
- case WDIOC_GETTIMEOUT:
- return put_user(booke_wdt_period, p);
case WDIOC_SETOPTIONS:
if (get_user(tmp, p))
return -EINVAL;
} else
return -EINVAL;
return 0;
+ case WDIOC_KEEPALIVE:
+ booke_wdt_ping();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(booke_wdt_period, p))
+ return -EFAULT;
+ mtspr(SPRN_TCR, (mfspr(SPRN_TCR) & ~WDTP(0)) |
+ WDTP(booke_wdt_period));
+ return 0;
+ case WDIOC_GETTIMEOUT:
+ return put_user(booke_wdt_period, p);
default:
return -ENOTTY;
}
if (booke_wdt_enabled == 0) {
booke_wdt_enabled = 1;
on_each_cpu(__booke_wdt_enable, NULL, 0);
- printk(KERN_INFO "PowerPC Book-E Watchdog Timer Enabled "
- "(wdt_period=%d)\n", booke_wdt_period);
+ printk(KERN_INFO
+ "PowerPC Book-E Watchdog Timer Enabled (wdt_period=%d)\n",
+ booke_wdt_period);
}
spin_unlock(&booke_wdt_lock);
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = booke_wdt_write,
- .ioctl = booke_wdt_ioctl,
+ .unlocked_ioctl = booke_wdt_ioctl,
.open = booke_wdt_open,
};
spin_lock(&booke_wdt_lock);
if (booke_wdt_enabled == 1) {
- printk(KERN_INFO "PowerPC Book-E Watchdog Timer Enabled "
- "(wdt_period=%d)\n", booke_wdt_period);
+ printk(KERN_INFO
+ "PowerPC Book-E Watchdog Timer Enabled (wdt_period=%d)\n",
+ booke_wdt_period);
on_each_cpu(__booke_wdt_enable, NULL, 0);
}
spin_unlock(&booke_wdt_lock);
#include <linux/timer.h>
#include <linux/completion.h>
#include <linux/jiffies.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-
+#include <linux/io.h>
+#include <linux/uaccess.h>
#include <linux/watchdog.h>
/* adjustable parameters */
-static int verbose = 0;
+static int verbose;
static int port = 0x91;
static int ticks = 10000;
+static spinlock_t cpu5wdt_lock;
#define PFX "cpu5wdt: "
static void cpu5wdt_trigger(unsigned long unused)
{
- if ( verbose > 2 )
+ if (verbose > 2)
printk(KERN_DEBUG PFX "trigger at %i ticks\n", ticks);
- if( cpu5wdt_device.running )
+ if (cpu5wdt_device.running)
ticks--;
+ spin_lock(&cpu5wdt_lock);
/* keep watchdog alive */
outb(1, port + CPU5WDT_TRIGGER_REG);
/* ticks doesn't matter anyway */
complete(&cpu5wdt_device.stop);
}
+ spin_unlock(&cpu5wdt_lock);
}
{
ticks = cpu5wdt_device.default_ticks;
- if ( verbose )
+ if (verbose)
printk(KERN_DEBUG PFX "reset (%i ticks)\n", (int) ticks);
}
static void cpu5wdt_start(void)
{
- if ( !cpu5wdt_device.queue ) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&cpu5wdt_lock, flags);
+ if (!cpu5wdt_device.queue) {
cpu5wdt_device.queue = 1;
outb(0, port + CPU5WDT_TIME_A_REG);
outb(0, port + CPU5WDT_TIME_B_REG);
}
/* if process dies, counter is not decremented */
cpu5wdt_device.running++;
+ spin_unlock_irqrestore(&cpu5wdt_lock, flags);
}
static int cpu5wdt_stop(void)
{
- if ( cpu5wdt_device.running )
- cpu5wdt_device.running = 0;
+ unsigned long flags;
+ spin_lock_irqsave(&cpu5wdt_lock, flags);
+ if (cpu5wdt_device.running)
+ cpu5wdt_device.running = 0;
ticks = cpu5wdt_device.default_ticks;
-
- if ( verbose )
+ spin_unlock_irqrestore(&cpu5wdt_lock, flags);
+ if (verbose)
printk(KERN_CRIT PFX "stop not possible\n");
-
return -EIO;
}
static int cpu5wdt_open(struct inode *inode, struct file *file)
{
- if ( test_and_set_bit(0, &cpu5wdt_device.inuse) )
+ if (test_and_set_bit(0, &cpu5wdt_device.inuse))
return -EBUSY;
-
return nonseekable_open(inode, file);
}
return 0;
}
-static int cpu5wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+static long cpu5wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
+ int __user *p = argp;
unsigned int value;
- static struct watchdog_info ident =
- {
+ static struct watchdog_info ident = {
.options = WDIOF_CARDRESET,
.identity = "CPU5 WDT",
};
- switch(cmd) {
- case WDIOC_KEEPALIVE:
- cpu5wdt_reset();
- break;
- case WDIOC_GETSTATUS:
- value = inb(port + CPU5WDT_STATUS_REG);
- value = (value >> 2) & 1;
- if ( copy_to_user(argp, &value, sizeof(int)) )
- return -EFAULT;
- break;
- case WDIOC_GETBOOTSTATUS:
- if ( copy_to_user(argp, &value, sizeof(int)) )
- return -EFAULT;
- break;
- case WDIOC_GETSUPPORT:
- if ( copy_to_user(argp, &ident, sizeof(ident)) )
- return -EFAULT;
- break;
- case WDIOC_SETOPTIONS:
- if ( copy_from_user(&value, argp, sizeof(int)) )
- return -EFAULT;
- switch(value) {
- case WDIOS_ENABLECARD:
- cpu5wdt_start();
- break;
- case WDIOS_DISABLECARD:
- return cpu5wdt_stop();
- default:
- return -EINVAL;
- }
- break;
- default:
- return -ENOTTY;
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
+ case WDIOC_GETSTATUS:
+ value = inb(port + CPU5WDT_STATUS_REG);
+ value = (value >> 2) & 1;
+ return put_user(value, p);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ if (get_user(value, p))
+ return -EFAULT;
+ if (value & WDIOS_ENABLECARD)
+ cpu5wdt_start();
+ if (value & WDIOS_DISABLECARD)
+ cpu5wdt_stop();
+ break;
+ case WDIOC_KEEPALIVE:
+ cpu5wdt_reset();
+ break;
+ default:
+ return -ENOTTY;
}
return 0;
}
-static ssize_t cpu5wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t cpu5wdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
- if ( !count )
+ if (!count)
return -EIO;
-
cpu5wdt_reset();
-
return count;
}
static const struct file_operations cpu5wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = cpu5wdt_ioctl,
+ .unlocked_ioctl = cpu5wdt_ioctl,
.open = cpu5wdt_open,
.write = cpu5wdt_write,
.release = cpu5wdt_release,
unsigned int val;
int err;
- if ( verbose )
- printk(KERN_DEBUG PFX "port=0x%x, verbose=%i\n", port, verbose);
+ if (verbose)
+ printk(KERN_DEBUG PFX
+ "port=0x%x, verbose=%i\n", port, verbose);
- if ( !request_region(port, CPU5WDT_EXTENT, PFX) ) {
+ init_completion(&cpu5wdt_device.stop);
+ spin_lock_init(&cpu5wdt_lock);
+ cpu5wdt_device.queue = 0;
+ setup_timer(&cpu5wdt_device.timer, cpu5wdt_trigger, 0);
+ cpu5wdt_device.default_ticks = ticks;
+
+ if (!request_region(port, CPU5WDT_EXTENT, PFX)) {
printk(KERN_ERR PFX "request_region failed\n");
err = -EBUSY;
goto no_port;
}
- if ( (err = misc_register(&cpu5wdt_misc)) < 0 ) {
- printk(KERN_ERR PFX "misc_register failed\n");
- goto no_misc;
- }
-
/* watchdog reboot? */
val = inb(port + CPU5WDT_STATUS_REG);
val = (val >> 2) & 1;
- if ( !val )
+ if (!val)
printk(KERN_INFO PFX "sorry, was my fault\n");
- init_completion(&cpu5wdt_device.stop);
- cpu5wdt_device.queue = 0;
-
- clear_bit(0, &cpu5wdt_device.inuse);
-
- setup_timer(&cpu5wdt_device.timer, cpu5wdt_trigger, 0);
+ err = misc_register(&cpu5wdt_misc);
+ if (err < 0) {
+ printk(KERN_ERR PFX "misc_register failed\n");
+ goto no_misc;
+ }
- cpu5wdt_device.default_ticks = ticks;
printk(KERN_INFO PFX "init success\n");
-
return 0;
no_misc:
static void __devexit cpu5wdt_exit(void)
{
- if ( cpu5wdt_device.queue ) {
+ if (cpu5wdt_device.queue) {
cpu5wdt_device.queue = 0;
wait_for_completion(&cpu5wdt_device.stop);
}
#include <linux/bitops.h>
#include <linux/platform_device.h>
#include <linux/spinlock.h>
-
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+#include <mach/hardware.h>
#define MODULE_NAME "DAVINCI-WDT: "
.identity = "DaVinci Watchdog",
};
-static int
-davinci_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long davinci_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int ret = -ENOTTY;
ret = put_user(0, (int *)arg);
break;
- case WDIOC_GETTIMEOUT:
- ret = put_user(heartbeat, (int *)arg);
- break;
-
case WDIOC_KEEPALIVE:
wdt_service();
ret = 0;
break;
+
+ case WDIOC_GETTIMEOUT:
+ ret = put_user(heartbeat, (int *)arg);
+ break;
}
return ret;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = davinci_wdt_write,
- .ioctl = davinci_wdt_ioctl,
+ .unlocked_ioctl = davinci_wdt_ioctl,
.open = davinci_wdt_open,
.release = davinci_wdt_release,
};
#include <linux/miscdevice.h>
#include <linux/watchdog.h>
#include <linux/timer.h>
-
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
+#include <mach/hardware.h>
#define WDT_VERSION "0.3"
#define PFX "ep93xx_wdt: "
.identity = "EP93xx Watchdog",
};
-static int
-ep93xx_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long ep93xx_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int ret = -ENOTTY;
ret = put_user(boot_status, (int __user *)arg);
break;
- case WDIOC_GETTIMEOUT:
- /* actually, it is 0.250 seconds.... */
- ret = put_user(1, (int __user *)arg);
- break;
-
case WDIOC_KEEPALIVE:
wdt_keepalive();
ret = 0;
break;
+
+ case WDIOC_GETTIMEOUT:
+ /* actually, it is 0.250 seconds.... */
+ ret = put_user(1, (int __user *)arg);
+ break;
}
return ret;
}
if (test_bit(WDT_OK_TO_CLOSE, &wdt_status))
wdt_shutdown();
else
- printk(KERN_CRIT PFX "Device closed unexpectedly - "
- "timer will not stop\n");
+ printk(KERN_CRIT PFX
+ "Device closed unexpectedly - timer will not stop\n");
clear_bit(WDT_IN_USE, &wdt_status);
clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
static const struct file_operations ep93xx_wdt_fops = {
.owner = THIS_MODULE,
.write = ep93xx_wdt_write,
- .ioctl = ep93xx_wdt_ioctl,
+ .unlocked_ioctl = ep93xx_wdt_ioctl,
.open = ep93xx_wdt_open,
.release = ep93xx_wdt_release,
};
MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started");
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=3600, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1<=timeout<=3600, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
MODULE_AUTHOR("Ray Lehtiniemi <rayl@mail.com>,"
"Alessandro Zummo <a.zummo@towertech.it>");
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
static unsigned long eurwdt_is_open;
static int eurwdt_timeout;
static char eur_expect_close;
+static spinlock_t eurwdt_lock;
/*
* You must set these - there is no sane way to probe for this board.
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Some symbolic names
{
eurwdt_disable_timer();
eurwdt_write_reg(WDT_CTRL_REG, 0x01); /* activate the WDT */
- eurwdt_write_reg(WDT_OUTPIN_CFG, !strcmp("int", ev) ? WDT_EVENT_INT : WDT_EVENT_REBOOT);
+ eurwdt_write_reg(WDT_OUTPIN_CFG,
+ !strcmp("int", ev) ? WDT_EVENT_INT : WDT_EVENT_REBOOT);
/* Setting interrupt line */
if (irq == 2 || irq > 15 || irq < 0) {
for (i = 0; i != count; i++) {
char c;
- if(get_user(c, buf+i))
+ if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
eur_expect_close = 42;
}
}
+ spin_lock(&eurwdt_lock);
eurwdt_ping(); /* the default timeout */
+ spin_unlock(&eurwdt_lock);
}
-
return count;
}
/**
* eurwdt_ioctl:
- * @inode: inode of the device
* @file: file handle to the device
* @cmd: watchdog command
* @arg: argument pointer
* according to their available features.
*/
-static int eurwdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long eurwdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "WDT Eurotech CPU-1220/1410",
};
int time;
int options, retval = -EINVAL;
- switch(cmd) {
- default:
- return -ENOTTY;
-
+ switch (cmd) {
case WDIOC_GETSUPPORT:
return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETBOOTSTATUS:
return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ if (get_user(options, p))
+ return -EFAULT;
+ spin_lock(&eurwdt_lock);
+ if (options & WDIOS_DISABLECARD) {
+ eurwdt_disable_timer();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ eurwdt_activate_timer();
+ eurwdt_ping();
+ retval = 0;
+ }
+ spin_unlock(&eurwdt_lock);
+ return retval;
+
case WDIOC_KEEPALIVE:
+ spin_lock(&eurwdt_lock);
eurwdt_ping();
+ spin_unlock(&eurwdt_lock);
return 0;
case WDIOC_SETTIMEOUT:
if (time < 0 || time > 255)
return -EINVAL;
+ spin_lock(&eurwdt_lock);
eurwdt_timeout = time;
eurwdt_set_timeout(time);
+ spin_unlock(&eurwdt_lock);
/* Fall */
case WDIOC_GETTIMEOUT:
return put_user(eurwdt_timeout, p);
- case WDIOC_SETOPTIONS:
- if (get_user(options, p))
- return -EFAULT;
- if (options & WDIOS_DISABLECARD) {
- eurwdt_disable_timer();
- retval = 0;
- }
- if (options & WDIOS_ENABLECARD) {
- eurwdt_activate_timer();
- eurwdt_ping();
- retval = 0;
- }
- return retval;
+ default:
+ return -ENOTTY;
}
}
static int eurwdt_release(struct inode *inode, struct file *file)
{
- if (eur_expect_close == 42) {
+ if (eur_expect_close == 42)
eurwdt_disable_timer();
- } else {
- printk(KERN_CRIT "eurwdt: Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT
+ "eurwdt: Unexpected close, not stopping watchdog!\n");
eurwdt_ping();
}
clear_bit(0, &eurwdt_is_open);
static int eurwdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT) {
- /* Turn the card off */
- eurwdt_disable_timer();
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ eurwdt_disable_timer(); /* Turn the card off */
return NOTIFY_DONE;
}
static const struct file_operations eurwdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = eurwdt_write,
- .ioctl = eurwdt_ioctl,
- .open = eurwdt_open,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = eurwdt_write,
+ .unlocked_ioctl = eurwdt_ioctl,
+ .open = eurwdt_open,
.release = eurwdt_release,
};
int ret;
ret = request_irq(irq, eurwdt_interrupt, IRQF_DISABLED, "eurwdt", NULL);
- if(ret) {
+ if (ret) {
printk(KERN_ERR "eurwdt: IRQ %d is not free.\n", irq);
goto out;
}
ret = register_reboot_notifier(&eurwdt_notifier);
if (ret) {
- printk(KERN_ERR "eurwdt: can't register reboot notifier (err=%d)\n", ret);
+ printk(KERN_ERR
+ "eurwdt: can't register reboot notifier (err=%d)\n", ret);
goto outreg;
}
+ spin_lock_init(&eurwdt_lock);
+
ret = misc_register(&eurwdt_miscdev);
if (ret) {
printk(KERN_ERR "eurwdt: can't misc_register on minor=%d\n",
#include <linux/fs.h>
#include <linux/platform_device.h>
#include <linux/reboot.h>
+#include <linux/uaccess.h>
-#include <asm/uaccess.h>
#include <asm/geode.h>
#define GEODEWDT_HZ 500
return 0;
}
-static int
-geodewdt_open(struct inode *inode, struct file *file)
+static int geodewdt_open(struct inode *inode, struct file *file)
{
- if (test_and_set_bit(WDT_FLAGS_OPEN, &wdt_flags))
- return -EBUSY;
+ if (test_and_set_bit(WDT_FLAGS_OPEN, &wdt_flags))
+ return -EBUSY;
- if (!test_and_clear_bit(WDT_FLAGS_ORPHAN, &wdt_flags))
- __module_get(THIS_MODULE);
+ if (!test_and_clear_bit(WDT_FLAGS_ORPHAN, &wdt_flags))
+ __module_get(THIS_MODULE);
geodewdt_ping();
- return nonseekable_open(inode, file);
+ return nonseekable_open(inode, file);
}
-static int
-geodewdt_release(struct inode *inode, struct file *file)
+static int geodewdt_release(struct inode *inode, struct file *file)
{
if (safe_close) {
geodewdt_disable();
module_put(THIS_MODULE);
- }
- else {
+ } else {
printk(KERN_CRIT "Unexpected close - watchdog is not stopping.\n");
geodewdt_ping();
return 0;
}
-static ssize_t
-geodewdt_write(struct file *file, const char __user *data, size_t len,
- loff_t *ppos)
+static ssize_t geodewdt_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
- if(len) {
+ if (len) {
if (!nowayout) {
size_t i;
safe_close = 0;
return len;
}
-static int
-geodewdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static int geodewdt_ioctl(struct inode *inode, struct file *file,
+ unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
| WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = WATCHDOG_NAME,
- };
+ };
- switch(cmd) {
+ switch (cmd) {
case WDIOC_GETSUPPORT:
return copy_to_user(argp, &ident,
sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETBOOTSTATUS:
return put_user(0, p);
- case WDIOC_KEEPALIVE:
- geodewdt_ping();
- return 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(interval, p))
- return -EFAULT;
-
- if (geodewdt_set_heartbeat(interval))
- return -EINVAL;
-
-/* Fall through */
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
case WDIOC_SETOPTIONS:
{
int options, ret = -EINVAL;
return ret;
}
+ case WDIOC_KEEPALIVE:
+ geodewdt_ping();
+ return 0;
+
+ case WDIOC_SETTIMEOUT:
+ if (get_user(interval, p))
+ return -EFAULT;
+
+ if (geodewdt_set_heartbeat(interval))
+ return -EINVAL;
+ /* Fall through */
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+
default:
return -ENOTTY;
}
}
static const struct file_operations geodewdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = geodewdt_write,
- .ioctl = geodewdt_ioctl,
- .open = geodewdt_open,
- .release = geodewdt_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = geodewdt_write,
+ .ioctl = geodewdt_ioctl,
+ .open = geodewdt_open,
+ .release = geodewdt_release,
};
static struct miscdevice geodewdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
- .fops = &geodewdt_fops
+ .fops = &geodewdt_fops,
};
-static int __devinit
-geodewdt_probe(struct platform_device *dev)
+static int __devinit geodewdt_probe(struct platform_device *dev)
{
int ret, timer;
return ret;
}
-static int __devexit
-geodewdt_remove(struct platform_device *dev)
+static int __devexit geodewdt_remove(struct platform_device *dev)
{
misc_deregister(&geodewdt_miscdev);
return 0;
}
-static void
-geodewdt_shutdown(struct platform_device *dev)
+static void geodewdt_shutdown(struct platform_device *dev)
{
geodewdt_disable();
}
},
};
-static int __init
-geodewdt_init(void)
+static int __init geodewdt_init(void)
{
int ret;
return ret;
}
-static void __exit
-geodewdt_exit(void)
+static void __exit geodewdt_exit(void)
{
platform_device_unregister(geodewdt_platform_device);
platform_driver_unregister(&geodewdt_driver);
#include <linux/string.h>
#include <linux/bootmem.h>
#include <linux/slab.h>
-#include <asm/dmi.h>
#include <asm/desc.h>
-#include <asm/kdebug.h>
#define PCI_BIOS32_SD_VALUE 0x5F32335F /* "_32_" */
#define CRU_BIOS_SIGNATURE_VALUE 0x55524324
dmi_walk(dmi_find_cru);
/* if cru_rom_addr has been set then we found a CRU service */
- return ((cru_rom_addr != NULL)? 0: -ENODEV);
+ return ((cru_rom_addr != NULL) ? 0: -ENODEV);
}
/* ------------------------------------------------------------------------- */
static int hpwdt_pretimeout(struct notifier_block *nb, unsigned long ulReason,
void *data)
{
- static unsigned long rom_pl;
+ unsigned long rom_pl;
static int die_nmi_called;
if (ulReason != DIE_NMI && ulReason != DIE_NMI_IPI)
/* scan to see whether or not we got the magic char. */
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_release = 42;
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*
- * based on i810-tco.c which is in turn based on softdog.c
+ * based on i810-tco.c which is in turn based on softdog.c
*
- * The timer is implemented in the following I/O controller hubs:
- * (See the intel documentation on http://developer.intel.com.)
- * 6300ESB chip : document number 300641-003
+ * The timer is implemented in the following I/O controller hubs:
+ * (See the intel documentation on http://developer.intel.com.)
+ * 6300ESB chip : document number 300641-003
*
* 2004YYZZ Ross Biro
* Initial version 0.01
* 2004YYZZ Ross Biro
- * Version 0.02
+ * Version 0.02
* 20050210 David Härdeman <david@2gen.com>
- * Ported driver to kernel 2.6
+ * Ported driver to kernel 2.6
*/
/*
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/ioport.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
/* Module and version information */
#define ESB_VERSION "0.03"
#define ESB_RELOAD_REG BASEADDR + 0x0c /* Reload register */
/* Lock register bits */
-#define ESB_WDT_FUNC ( 0x01 << 2 ) /* Watchdog functionality */
-#define ESB_WDT_ENABLE ( 0x01 << 1 ) /* Enable WDT */
-#define ESB_WDT_LOCK ( 0x01 << 0 ) /* Lock (nowayout) */
+#define ESB_WDT_FUNC (0x01 << 2) /* Watchdog functionality */
+#define ESB_WDT_ENABLE (0x01 << 1) /* Enable WDT */
+#define ESB_WDT_LOCK (0x01 << 0) /* Lock (nowayout) */
/* Config register bits */
-#define ESB_WDT_REBOOT ( 0x01 << 5 ) /* Enable reboot on timeout */
-#define ESB_WDT_FREQ ( 0x01 << 2 ) /* Decrement frequency */
-#define ESB_WDT_INTTYPE ( 0x11 << 0 ) /* Interrupt type on timer1 timeout */
+#define ESB_WDT_REBOOT (0x01 << 5) /* Enable reboot on timeout */
+#define ESB_WDT_FREQ (0x01 << 2) /* Decrement frequency */
+#define ESB_WDT_INTTYPE (0x11 << 0) /* Interrupt type on timer1 timeout */
/* Reload register bits */
-#define ESB_WDT_RELOAD ( 0x01 << 8 ) /* prevent timeout */
+#define ESB_WDT_RELOAD (0x01 << 8) /* prevent timeout */
/* Magic constants */
#define ESB_UNLOCK1 0x80 /* Step 1 to unlock reset registers */
static char esb_expect_close;
/* module parameters */
-#define WATCHDOG_HEARTBEAT 30 /* 30 sec default heartbeat (1<heartbeat<2*1023) */
+/* 30 sec default heartbeat (1 < heartbeat < 2*1023) */
+#define WATCHDOG_HEARTBEAT 30
static int heartbeat = WATCHDOG_HEARTBEAT; /* in seconds */
+
module_param(heartbeat, int, 0);
-MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (1<heartbeat<2046, default=" __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
+MODULE_PARM_DESC(heartbeat,
+ "Watchdog heartbeat in seconds. (1<heartbeat<2046, default="
+ __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Some i6300ESB specific functions
* reload register. After this the appropriate registers can be written
* to once before they need to be unlocked again.
*/
-static inline void esb_unlock_registers(void) {
- writeb(ESB_UNLOCK1, ESB_RELOAD_REG);
- writeb(ESB_UNLOCK2, ESB_RELOAD_REG);
+static inline void esb_unlock_registers(void)
+{
+ writeb(ESB_UNLOCK1, ESB_RELOAD_REG);
+ writeb(ESB_UNLOCK2, ESB_RELOAD_REG);
}
static void esb_timer_start(void)
/* Enable or Enable + Lock? */
val = 0x02 | (nowayout ? 0x01 : 0x00);
-
- pci_write_config_byte(esb_pci, ESB_LOCK_REG, val);
+ pci_write_config_byte(esb_pci, ESB_LOCK_REG, val);
}
static int esb_timer_stop(void)
spin_lock(&esb_lock);
esb_unlock_registers();
writew(ESB_WDT_RELOAD, ESB_RELOAD_REG);
- /* FIXME: Do we need to flush anything here? */
+ /* FIXME: Do we need to flush anything here? */
spin_unlock(&esb_lock);
}
/* Write timer 2 */
esb_unlock_registers();
- writel(val, ESB_TIMER2_REG);
+ writel(val, ESB_TIMER2_REG);
- /* Reload */
+ /* Reload */
esb_unlock_registers();
writew(ESB_WDT_RELOAD, ESB_RELOAD_REG);
return 0;
}
-static int esb_timer_read (void)
+static int esb_timer_read(void)
{
- u32 count;
+ u32 count;
/* This isn't documented, and doesn't take into
- * acount which stage is running, but it looks
- * like a 20 bit count down, so we might as well report it.
- */
- pci_read_config_dword(esb_pci, 0x64, &count);
- return (int)count;
+ * acount which stage is running, but it looks
+ * like a 20 bit count down, so we might as well report it.
+ */
+ pci_read_config_dword(esb_pci, 0x64, &count);
+ return (int)count;
}
/*
- * /dev/watchdog handling
+ * /dev/watchdog handling
*/
-static int esb_open (struct inode *inode, struct file *file)
+static int esb_open(struct inode *inode, struct file *file)
{
- /* /dev/watchdog can only be opened once */
- if (test_and_set_bit(0, &timer_alive))
- return -EBUSY;
+ /* /dev/watchdog can only be opened once */
+ if (test_and_set_bit(0, &timer_alive))
+ return -EBUSY;
- /* Reload and activate timer */
- esb_timer_keepalive ();
- esb_timer_start ();
+ /* Reload and activate timer */
+ esb_timer_keepalive();
+ esb_timer_start();
return nonseekable_open(inode, file);
}
-static int esb_release (struct inode *inode, struct file *file)
+static int esb_release(struct inode *inode, struct file *file)
{
- /* Shut off the timer. */
- if (esb_expect_close == 42) {
- esb_timer_stop ();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
- esb_timer_keepalive ();
- }
- clear_bit(0, &timer_alive);
- esb_expect_close = 0;
- return 0;
+ /* Shut off the timer. */
+ if (esb_expect_close == 42)
+ esb_timer_stop();
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
+ esb_timer_keepalive();
+ }
+ clear_bit(0, &timer_alive);
+ esb_expect_close = 0;
+ return 0;
}
-static ssize_t esb_write (struct file *file, const char __user *data,
- size_t len, loff_t * ppos)
+static ssize_t esb_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if (len) {
+ if (len) {
if (!nowayout) {
size_t i;
/* scan to see whether or not we got the magic character */
for (i = 0; i != len; i++) {
char c;
- if(get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
esb_expect_close = 42;
}
/* someone wrote to us, we should reload the timer */
- esb_timer_keepalive ();
+ esb_timer_keepalive();
}
return len;
}
-static int esb_ioctl (struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long esb_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int new_options, retval = -EINVAL;
int new_heartbeat;
void __user *argp = (void __user *)arg;
int __user *p = argp;
static struct watchdog_info ident = {
- .options = WDIOF_SETTIMEOUT |
+ .options = WDIOF_SETTIMEOUT |
WDIOF_KEEPALIVEPING |
WDIOF_MAGICCLOSE,
- .firmware_version = 0,
- .identity = ESB_MODULE_NAME,
+ .firmware_version = 0,
+ .identity = ESB_MODULE_NAME,
};
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof (ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- return put_user (esb_timer_read(), p);
-
- case WDIOC_GETBOOTSTATUS:
- return put_user (triggered, p);
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident,
+ sizeof(ident)) ? -EFAULT : 0;
- case WDIOC_KEEPALIVE:
- esb_timer_keepalive ();
- return 0;
+ case WDIOC_GETSTATUS:
+ return put_user(esb_timer_read(), p);
- case WDIOC_SETOPTIONS:
- {
- if (get_user (new_options, p))
- return -EFAULT;
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(triggered, p);
- if (new_options & WDIOS_DISABLECARD) {
- esb_timer_stop ();
- retval = 0;
- }
+ case WDIOC_SETOPTIONS:
+ {
+ if (get_user(new_options, p))
+ return -EFAULT;
- if (new_options & WDIOS_ENABLECARD) {
- esb_timer_keepalive ();
- esb_timer_start ();
- retval = 0;
- }
-
- return retval;
- }
-
- case WDIOC_SETTIMEOUT:
- {
- if (get_user(new_heartbeat, p))
- return -EFAULT;
-
- if (esb_timer_set_heartbeat(new_heartbeat))
- return -EINVAL;
-
- esb_timer_keepalive ();
- /* Fall */
- }
-
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
+ if (new_options & WDIOS_DISABLECARD) {
+ esb_timer_stop();
+ retval = 0;
+ }
- default:
- return -ENOTTY;
- }
+ if (new_options & WDIOS_ENABLECARD) {
+ esb_timer_keepalive();
+ esb_timer_start();
+ retval = 0;
+ }
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ esb_timer_keepalive();
+ return 0;
+
+ case WDIOC_SETTIMEOUT:
+ {
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
+ if (esb_timer_set_heartbeat(new_heartbeat))
+ return -EINVAL;
+ esb_timer_keepalive();
+ /* Fall */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
+ default:
+ return -ENOTTY;
+ }
}
/*
* Notify system
*/
-static int esb_notify_sys (struct notifier_block *this, unsigned long code, void *unused)
+static int esb_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the WDT off */
- esb_timer_stop ();
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ esb_timer_stop(); /* Turn the WDT off */
- return NOTIFY_DONE;
+ return NOTIFY_DONE;
}
/*
*/
static const struct file_operations esb_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = esb_write,
- .ioctl = esb_ioctl,
- .open = esb_open,
- .release = esb_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = esb_write,
+ .unlocked_ioctl = esb_ioctl,
+ .open = esb_open,
+ .release = esb_release,
};
static struct miscdevice esb_miscdev = {
- .minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &esb_fops,
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &esb_fops,
};
static struct notifier_block esb_notifier = {
- .notifier_call = esb_notify_sys,
+ .notifier_call = esb_notify_sys,
};
/*
* want to register another driver on the same PCI id.
*/
static struct pci_device_id esb_pci_tbl[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_9), },
- { 0, }, /* End of list */
+ { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_9), },
+ { 0, }, /* End of list */
};
-MODULE_DEVICE_TABLE (pci, esb_pci_tbl);
+MODULE_DEVICE_TABLE(pci, esb_pci_tbl);
/*
* Init & exit routines
*/
-static unsigned char __init esb_getdevice (void)
+static unsigned char __init esb_getdevice(void)
{
u8 val1;
unsigned short val2;
+ /*
+ * Find the PCI device
+ */
- struct pci_dev *dev = NULL;
- /*
- * Find the PCI device
- */
-
- for_each_pci_dev(dev) {
- if (pci_match_id(esb_pci_tbl, dev)) {
- esb_pci = dev;
- break;
- }
- }
+ esb_pci = pci_get_device(PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_ESB_9, NULL);
- if (esb_pci) {
- if (pci_enable_device(esb_pci)) {
- printk (KERN_ERR PFX "failed to enable device\n");
+ if (esb_pci) {
+ if (pci_enable_device(esb_pci)) {
+ printk(KERN_ERR PFX "failed to enable device\n");
goto err_devput;
}
if (pci_request_region(esb_pci, 0, ESB_MODULE_NAME)) {
- printk (KERN_ERR PFX "failed to request region\n");
+ printk(KERN_ERR PFX "failed to request region\n");
goto err_disable;
}
BASEADDR = ioremap(pci_resource_start(esb_pci, 0),
pci_resource_len(esb_pci, 0));
if (BASEADDR == NULL) {
- /* Something's wrong here, BASEADDR has to be set */
- printk (KERN_ERR PFX "failed to get BASEADDR\n");
- goto err_release;
- }
+ /* Something's wrong here, BASEADDR has to be set */
+ printk(KERN_ERR PFX "failed to get BASEADDR\n");
+ goto err_release;
+ }
/*
* The watchdog has two timers, it can be setup so that the
/* Check that the WDT isn't already locked */
pci_read_config_byte(esb_pci, ESB_LOCK_REG, &val1);
if (val1 & ESB_WDT_LOCK)
- printk (KERN_WARNING PFX "nowayout already set\n");
+ printk(KERN_WARNING PFX "nowayout already set\n");
/* Set the timer to watchdog mode and disable it for now */
pci_write_config_byte(esb_pci, ESB_LOCK_REG, 0x00);
return 0;
}
-static int __init watchdog_init (void)
+static int __init watchdog_init(void)
{
- int ret;
-
- /* Check whether or not the hardware watchdog is there */
- if (!esb_getdevice () || esb_pci == NULL)
- return -ENODEV;
-
- /* Check that the heartbeat value is within it's range ; if not reset to the default */
- if (esb_timer_set_heartbeat (heartbeat)) {
- esb_timer_set_heartbeat (WATCHDOG_HEARTBEAT);
- printk(KERN_INFO PFX "heartbeat value must be 1<heartbeat<2046, using %d\n",
- heartbeat);
- }
-
- ret = register_reboot_notifier(&esb_notifier);
- if (ret != 0) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
- goto err_unmap;
- }
-
- ret = misc_register(&esb_miscdev);
- if (ret != 0) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
- goto err_notifier;
- }
-
- esb_timer_stop ();
-
- printk (KERN_INFO PFX "initialized (0x%p). heartbeat=%d sec (nowayout=%d)\n",
- BASEADDR, heartbeat, nowayout);
+ int ret;
+
+ /* Check whether or not the hardware watchdog is there */
+ if (!esb_getdevice() || esb_pci == NULL)
+ return -ENODEV;
+
+ /* Check that the heartbeat value is within it's range;
+ if not reset to the default */
+ if (esb_timer_set_heartbeat(heartbeat)) {
+ esb_timer_set_heartbeat(WATCHDOG_HEARTBEAT);
+ printk(KERN_INFO PFX
+ "heartbeat value must be 1<heartbeat<2046, using %d\n",
+ heartbeat);
+ }
+ ret = register_reboot_notifier(&esb_notifier);
+ if (ret != 0) {
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
+ goto err_unmap;
+ }
- return 0;
+ ret = misc_register(&esb_miscdev);
+ if (ret != 0) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
+ goto err_notifier;
+ }
+ esb_timer_stop();
+ printk(KERN_INFO PFX
+ "initialized (0x%p). heartbeat=%d sec (nowayout=%d)\n",
+ BASEADDR, heartbeat, nowayout);
+ return 0;
err_notifier:
- unregister_reboot_notifier(&esb_notifier);
+ unregister_reboot_notifier(&esb_notifier);
err_unmap:
iounmap(BASEADDR);
/* err_release: */
pci_disable_device(esb_pci);
/* err_devput: */
pci_dev_put(esb_pci);
- return ret;
+ return ret;
}
-static void __exit watchdog_cleanup (void)
+static void __exit watchdog_cleanup(void)
{
/* Stop the timer before we leave */
if (!nowayout)
- esb_timer_stop ();
+ esb_timer_stop();
/* Deregister */
misc_deregister(&esb_miscdev);
- unregister_reboot_notifier(&esb_notifier);
+ unregister_reboot_notifier(&esb_notifier);
iounmap(BASEADDR);
pci_release_region(esb_pci, 0);
pci_disable_device(esb_pci);
--- /dev/null
+/* iTCO Vendor Specific Support hooks */
+#ifdef CONFIG_ITCO_VENDOR_SUPPORT
+extern void iTCO_vendor_pre_start(unsigned long, unsigned int);
+extern void iTCO_vendor_pre_stop(unsigned long);
+extern void iTCO_vendor_pre_keepalive(unsigned long, unsigned int);
+extern void iTCO_vendor_pre_set_heartbeat(unsigned int);
+extern int iTCO_vendor_check_noreboot_on(void);
+#else
+#define iTCO_vendor_pre_start(acpibase, heartbeat) {}
+#define iTCO_vendor_pre_stop(acpibase) {}
+#define iTCO_vendor_pre_keepalive(acpibase, heartbeat) {}
+#define iTCO_vendor_pre_set_heartbeat(heartbeat) {}
+#define iTCO_vendor_check_noreboot_on() 1
+ /* 1=check noreboot; 0=don't check */
+#endif
*/
/* Module and version information */
-#define DRV_NAME "iTCO_vendor_support"
-#define DRV_VERSION "1.01"
-#define DRV_RELDATE "11-Nov-2006"
+#define DRV_NAME "iTCO_vendor_support"
+#define DRV_VERSION "1.01"
+#define DRV_RELDATE "11-Nov-2006"
#define PFX DRV_NAME ": "
/* Includes */
#include <linux/kernel.h> /* For printk/panic/... */
#include <linux/init.h> /* For __init/__exit/... */
#include <linux/ioport.h> /* For io-port access */
+#include <linux/io.h> /* For inb/outb/... */
-#include <asm/io.h> /* For inb/outb/... */
+#include "iTCO_vendor.h"
/* iTCO defines */
#define SMI_EN acpibase + 0x30 /* SMI Control and Enable Register */
-#define TCOBASE acpibase + 0x60 /* TCO base address */
-#define TCO1_STS TCOBASE + 0x04 /* TCO1 Status Register */
+#define TCOBASE acpibase + 0x60 /* TCO base address */
+#define TCO1_STS TCOBASE + 0x04 /* TCO1 Status Register */
/* List of vendor support modes */
-#define SUPERMICRO_OLD_BOARD 1 /* SuperMicro Pentium 3 Era 370SSE+-OEM1/P3TSSE */
-#define SUPERMICRO_NEW_BOARD 2 /* SuperMicro Pentium 4 / Xeon 4 / EMT64T Era Systems */
+/* SuperMicro Pentium 3 Era 370SSE+-OEM1/P3TSSE */
+#define SUPERMICRO_OLD_BOARD 1
+/* SuperMicro Pentium 4 / Xeon 4 / EMT64T Era Systems */
+#define SUPERMICRO_NEW_BOARD 2
-static int vendorsupport = 0;
+static int vendorsupport;
module_param(vendorsupport, int, 0);
MODULE_PARM_DESC(vendorsupport, "iTCO vendor specific support mode, default=0 (none), 1=SuperMicro Pent3, 2=SuperMicro Pent4+");
*/
/* I/O Port's */
-#define SM_REGINDEX 0x2e /* SuperMicro ICH4+ Register Index */
-#define SM_DATAIO 0x2f /* SuperMicro ICH4+ Register Data I/O */
+#define SM_REGINDEX 0x2e /* SuperMicro ICH4+ Register Index */
+#define SM_DATAIO 0x2f /* SuperMicro ICH4+ Register Data I/O */
/* Control Register's */
-#define SM_CTLPAGESW 0x07 /* SuperMicro ICH4+ Control Page Switch */
-#define SM_CTLPAGE 0x08 /* SuperMicro ICH4+ Control Page Num */
+#define SM_CTLPAGESW 0x07 /* SuperMicro ICH4+ Control Page Switch */
+#define SM_CTLPAGE 0x08 /* SuperMicro ICH4+ Control Page Num */
-#define SM_WATCHENABLE 0x30 /* Watchdog enable: Bit 0: 0=off, 1=on */
+#define SM_WATCHENABLE 0x30 /* Watchdog enable: Bit 0: 0=off, 1=on */
-#define SM_WATCHPAGE 0x87 /* Watchdog unlock control page */
+#define SM_WATCHPAGE 0x87 /* Watchdog unlock control page */
-#define SM_ENDWATCH 0xAA /* Watchdog lock control page */
+#define SM_ENDWATCH 0xAA /* Watchdog lock control page */
-#define SM_COUNTMODE 0xf5 /* Watchdog count mode select */
- /* (Bit 3: 0 = seconds, 1 = minutes */
+#define SM_COUNTMODE 0xf5 /* Watchdog count mode select */
+ /* (Bit 3: 0 = seconds, 1 = minutes */
-#define SM_WATCHTIMER 0xf6 /* 8-bits, Watchdog timer counter (RW) */
+#define SM_WATCHTIMER 0xf6 /* 8-bits, Watchdog timer counter (RW) */
-#define SM_RESETCONTROL 0xf7 /* Watchdog reset control */
- /* Bit 6: timer is reset by kbd interrupt */
- /* Bit 7: timer is reset by mouse interrupt */
+#define SM_RESETCONTROL 0xf7 /* Watchdog reset control */
+ /* Bit 6: timer is reset by kbd interrupt */
+ /* Bit 7: timer is reset by mouse interrupt */
static void supermicro_new_unlock_watchdog(void)
{
- outb(SM_WATCHPAGE, SM_REGINDEX); /* Write 0x87 to port 0x2e twice */
+ /* Write 0x87 to port 0x2e twice */
outb(SM_WATCHPAGE, SM_REGINDEX);
-
- outb(SM_CTLPAGESW, SM_REGINDEX); /* Switch to watchdog control page */
+ outb(SM_WATCHPAGE, SM_REGINDEX);
+ /* Switch to watchdog control page */
+ outb(SM_CTLPAGESW, SM_REGINDEX);
outb(SM_CTLPAGE, SM_DATAIO);
}
outb(val, SM_DATAIO);
/* Write heartbeat interval to WDOG */
- outb (SM_WATCHTIMER, SM_REGINDEX);
+ outb(SM_WATCHTIMER, SM_REGINDEX);
outb((heartbeat & 255), SM_DATAIO);
/* Make sure keyboard/mouse interrupts don't interfere */
int iTCO_vendor_check_noreboot_on(void)
{
- switch(vendorsupport) {
+ switch (vendorsupport) {
case SUPERMICRO_OLD_BOARD:
return 0;
default:
static int __init iTCO_vendor_init_module(void)
{
- printk (KERN_INFO PFX "vendor-support=%d\n", vendorsupport);
+ printk(KERN_INFO PFX "vendor-support=%d\n", vendorsupport);
return 0;
}
static void __exit iTCO_vendor_exit_module(void)
{
- printk (KERN_INFO PFX "Module Unloaded\n");
+ printk(KERN_INFO PFX "Module Unloaded\n");
}
module_init(iTCO_vendor_init_module);
*/
/* Module and version information */
-#define DRV_NAME "iTCO_wdt"
-#define DRV_VERSION "1.03"
-#define DRV_RELDATE "30-Apr-2008"
+#define DRV_NAME "iTCO_wdt"
+#define DRV_VERSION "1.03"
+#define DRV_RELDATE "30-Apr-2008"
#define PFX DRV_NAME ": "
/* Includes */
#include <linux/types.h> /* For standard types (like size_t) */
#include <linux/errno.h> /* For the -ENODEV/... values */
#include <linux/kernel.h> /* For printk/panic/... */
-#include <linux/miscdevice.h> /* For MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR) */
+#include <linux/miscdevice.h> /* For MODULE_ALIAS_MISCDEV
+ (WATCHDOG_MINOR) */
#include <linux/watchdog.h> /* For the watchdog specific items */
#include <linux/init.h> /* For __init/__exit/... */
#include <linux/fs.h> /* For file operations */
#include <linux/pci.h> /* For pci functions */
#include <linux/ioport.h> /* For io-port access */
#include <linux/spinlock.h> /* For spin_lock/spin_unlock/... */
+#include <linux/uaccess.h> /* For copy_to_user/put_user/... */
+#include <linux/io.h> /* For inb/outb/... */
-#include <asm/uaccess.h> /* For copy_to_user/put_user/... */
-#include <asm/io.h> /* For inb/outb/... */
+#include "iTCO_vendor.h"
/* TCO related info */
enum iTCO_chipsets {
TCO_ICH9, /* ICH9 */
TCO_ICH9R, /* ICH9R */
TCO_ICH9DH, /* ICH9DH */
- TCO_ICH9DO, /* ICH9DO */
+ TCO_ICH9DO, /* ICH9DO */
TCO_631XESB, /* 631xESB/632xESB */
};
{"ICH9DH", 2},
{"ICH9DO", 2},
{"631xESB/632xESB", 2},
- {NULL,0}
+ {NULL, 0}
};
#define ITCO_PCI_DEVICE(dev, data) \
* functions that probably will be registered by other drivers.
*/
static struct pci_device_id iTCO_wdt_pci_tbl[] = {
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801AA_0, TCO_ICH )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801AB_0, TCO_ICH0 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801BA_0, TCO_ICH2 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801BA_10, TCO_ICH2M )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801CA_0, TCO_ICH3 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801CA_12, TCO_ICH3M )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801DB_0, TCO_ICH4 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801DB_12, TCO_ICH4M )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801E_0, TCO_CICH )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801EB_0, TCO_ICH5 )},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801AA_0, TCO_ICH)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801AB_0, TCO_ICH0)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801BA_0, TCO_ICH2)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801BA_10, TCO_ICH2M)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801CA_0, TCO_ICH3)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801CA_12, TCO_ICH3M)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801DB_0, TCO_ICH4)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801DB_12, TCO_ICH4M)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801E_0, TCO_CICH)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_82801EB_0, TCO_ICH5)},
{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ESB_1, TCO_6300ESB)},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_0, TCO_ICH6 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_1, TCO_ICH6M )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_2, TCO_ICH6W )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0, TCO_ICH7 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1, TCO_ICH7M )},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_0, TCO_ICH6)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_1, TCO_ICH6M)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_2, TCO_ICH6W)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0, TCO_ICH7)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1, TCO_ICH7M)},
{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_31, TCO_ICH7MDH)},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0, TCO_ICH8 )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1, TCO_ICH8ME )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2, TCO_ICH8DH )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3, TCO_ICH8DO )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4, TCO_ICH8M )},
- { ITCO_PCI_DEVICE(0x2918, TCO_ICH9 )},
- { ITCO_PCI_DEVICE(0x2916, TCO_ICH9R )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2, TCO_ICH9DH )},
- { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4, TCO_ICH9DO )},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0, TCO_ICH8)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1, TCO_ICH8ME)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2, TCO_ICH8DH)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3, TCO_ICH8DO)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4, TCO_ICH8M)},
+ { ITCO_PCI_DEVICE(0x2918, TCO_ICH9)},
+ { ITCO_PCI_DEVICE(0x2916, TCO_ICH9R)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2, TCO_ICH9DH)},
+ { ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4, TCO_ICH9DO)},
{ ITCO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ESB2_0, TCO_631XESB)},
{ ITCO_PCI_DEVICE(0x2671, TCO_631XESB)},
{ ITCO_PCI_DEVICE(0x2672, TCO_631XESB)},
{ ITCO_PCI_DEVICE(0x267f, TCO_631XESB)},
{ 0, }, /* End of list */
};
-MODULE_DEVICE_TABLE (pci, iTCO_wdt_pci_tbl);
+MODULE_DEVICE_TABLE(pci, iTCO_wdt_pci_tbl);
/* Address definitions for the TCO */
-#define TCOBASE iTCO_wdt_private.ACPIBASE + 0x60 /* TCO base address */
-#define SMI_EN iTCO_wdt_private.ACPIBASE + 0x30 /* SMI Control and Enable Register */
+/* TCO base address */
+#define TCOBASE iTCO_wdt_private.ACPIBASE + 0x60
+/* SMI Control and Enable Register */
+#define SMI_EN iTCO_wdt_private.ACPIBASE + 0x30
-#define TCO_RLD TCOBASE + 0x00 /* TCO Timer Reload and Current Value */
+#define TCO_RLD TCOBASE + 0x00 /* TCO Timer Reload and Curr. Value */
#define TCOv1_TMR TCOBASE + 0x01 /* TCOv1 Timer Initial Value */
#define TCO_DAT_IN TCOBASE + 0x02 /* TCO Data In Register */
#define TCO_DAT_OUT TCOBASE + 0x03 /* TCO Data Out Register */
/* internal variables */
static unsigned long is_active;
static char expect_release;
-static struct { /* this is private data for the iTCO_wdt device */
- unsigned int iTCO_version; /* TCO version/generation */
- unsigned long ACPIBASE; /* The cards ACPIBASE address (TCOBASE = ACPIBASE+0x60) */
- unsigned long __iomem *gcs; /* NO_REBOOT flag is Memory-Mapped GCS register bit 5 (TCO version 2) */
- spinlock_t io_lock; /* the lock for io operations */
- struct pci_dev *pdev; /* the PCI-device */
+static struct { /* this is private data for the iTCO_wdt device */
+ /* TCO version/generation */
+ unsigned int iTCO_version;
+ /* The cards ACPIBASE address (TCOBASE = ACPIBASE+0x60) */
+ unsigned long ACPIBASE;
+ /* NO_REBOOT flag is Memory-Mapped GCS register bit 5 (TCO version 2)*/
+ unsigned long __iomem *gcs;
+ /* the lock for io operations */
+ spinlock_t io_lock;
+ /* the PCI-device */
+ struct pci_dev *pdev;
} iTCO_wdt_private;
-static struct platform_device *iTCO_wdt_platform_device; /* the watchdog platform device */
+/* the watchdog platform device */
+static struct platform_device *iTCO_wdt_platform_device;
/* module parameters */
#define WATCHDOG_HEARTBEAT 30 /* 30 sec default heartbeat */
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
-
-/* iTCO Vendor Specific Support hooks */
-#ifdef CONFIG_ITCO_VENDOR_SUPPORT
-extern void iTCO_vendor_pre_start(unsigned long, unsigned int);
-extern void iTCO_vendor_pre_stop(unsigned long);
-extern void iTCO_vendor_pre_keepalive(unsigned long, unsigned int);
-extern void iTCO_vendor_pre_set_heartbeat(unsigned int);
-extern int iTCO_vendor_check_noreboot_on(void);
-#else
-#define iTCO_vendor_pre_start(acpibase, heartbeat) {}
-#define iTCO_vendor_pre_stop(acpibase) {}
-#define iTCO_vendor_pre_keepalive(acpibase,heartbeat) {}
-#define iTCO_vendor_pre_set_heartbeat(heartbeat) {}
-#define iTCO_vendor_check_noreboot_on() 1 /* 1=check noreboot; 0=don't check */
-#endif
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Some TCO specific functions
iTCO_vendor_pre_keepalive(iTCO_wdt_private.ACPIBASE, heartbeat);
/* Reload the timer by writing to the TCO Timer Counter register */
- if (iTCO_wdt_private.iTCO_version == 2) {
+ if (iTCO_wdt_private.iTCO_version == 2)
outw(0x01, TCO_RLD);
- } else if (iTCO_wdt_private.iTCO_version == 1) {
+ else if (iTCO_wdt_private.iTCO_version == 1)
outb(0x01, TCO_RLD);
- }
spin_unlock(&iTCO_wdt_private.io_lock);
return 0;
return 0;
}
-static int iTCO_wdt_get_timeleft (int *time_left)
+static int iTCO_wdt_get_timeleft(int *time_left)
{
unsigned int val16;
unsigned char val8;
* /dev/watchdog handling
*/
-static int iTCO_wdt_open (struct inode *inode, struct file *file)
+static int iTCO_wdt_open(struct inode *inode, struct file *file)
{
/* /dev/watchdog can only be opened once */
if (test_and_set_bit(0, &is_active))
return nonseekable_open(inode, file);
}
-static int iTCO_wdt_release (struct inode *inode, struct file *file)
+static int iTCO_wdt_release(struct inode *inode, struct file *file)
{
/*
* Shut off the timer.
if (expect_release == 42) {
iTCO_wdt_stop();
} else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
iTCO_wdt_keepalive();
}
clear_bit(0, &is_active);
return 0;
}
-static ssize_t iTCO_wdt_write (struct file *file, const char __user *data,
- size_t len, loff_t * ppos)
+static ssize_t iTCO_wdt_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
if (len) {
if (!nowayout) {
size_t i;
- /* note: just in case someone wrote the magic character
- * five months ago... */
+ /* note: just in case someone wrote the magic
+ character five months ago... */
expect_release = 0;
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got the
+ magic character */
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_release = 42;
return len;
}
-static int iTCO_wdt_ioctl (struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long iTCO_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_options, retval = -EINVAL;
int new_heartbeat;
};
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof (ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- iTCO_wdt_keepalive();
- return 0;
-
- case WDIOC_SETOPTIONS:
- {
- if (get_user(new_options, p))
- return -EFAULT;
-
- if (new_options & WDIOS_DISABLECARD) {
- iTCO_wdt_stop();
- retval = 0;
- }
-
- if (new_options & WDIOS_ENABLECARD) {
- iTCO_wdt_keepalive();
- iTCO_wdt_start();
- retval = 0;
- }
-
- return retval;
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+
+ case WDIOC_SETOPTIONS:
+ {
+ if (get_user(new_options, p))
+ return -EFAULT;
+
+ if (new_options & WDIOS_DISABLECARD) {
+ iTCO_wdt_stop();
+ retval = 0;
}
-
- case WDIOC_SETTIMEOUT:
- {
- if (get_user(new_heartbeat, p))
- return -EFAULT;
-
- if (iTCO_wdt_set_heartbeat(new_heartbeat))
- return -EINVAL;
-
+ if (new_options & WDIOS_ENABLECARD) {
iTCO_wdt_keepalive();
- /* Fall */
- }
-
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
-
- case WDIOC_GETTIMELEFT:
- {
- int time_left;
-
- if (iTCO_wdt_get_timeleft(&time_left))
- return -EINVAL;
-
- return put_user(time_left, p);
+ iTCO_wdt_start();
+ retval = 0;
}
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ iTCO_wdt_keepalive();
+ return 0;
- default:
- return -ENOTTY;
+ case WDIOC_SETTIMEOUT:
+ {
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
+ if (iTCO_wdt_set_heartbeat(new_heartbeat))
+ return -EINVAL;
+ iTCO_wdt_keepalive();
+ /* Fall */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
+ case WDIOC_GETTIMELEFT:
+ {
+ int time_left;
+ if (iTCO_wdt_get_timeleft(&time_left))
+ return -EINVAL;
+ return put_user(time_left, p);
+ }
+ default:
+ return -ENOTTY;
}
}
*/
static const struct file_operations iTCO_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = iTCO_wdt_write,
- .ioctl = iTCO_wdt_ioctl,
- .open = iTCO_wdt_open,
- .release = iTCO_wdt_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = iTCO_wdt_write,
+ .unlocked_ioctl = iTCO_wdt_ioctl,
+ .open = iTCO_wdt_open,
+ .release = iTCO_wdt_release,
};
static struct miscdevice iTCO_wdt_miscdev = {
* Init & exit routines
*/
-static int __devinit iTCO_wdt_init(struct pci_dev *pdev, const struct pci_device_id *ent, struct platform_device *dev)
+static int __devinit iTCO_wdt_init(struct pci_dev *pdev,
+ const struct pci_device_id *ent, struct platform_device *dev)
{
int ret;
u32 base_address;
pci_dev_put(pdev);
return -ENODEV;
}
- iTCO_wdt_private.iTCO_version = iTCO_chipset_info[ent->driver_data].iTCO_version;
+ iTCO_wdt_private.iTCO_version =
+ iTCO_chipset_info[ent->driver_data].iTCO_version;
iTCO_wdt_private.ACPIBASE = base_address;
iTCO_wdt_private.pdev = pdev;
- /* Get the Memory-Mapped GCS register, we need it for the NO_REBOOT flag (TCO v2) */
- /* To get access to it you have to read RCBA from PCI Config space 0xf0
- and use it as base. GCS = RCBA + ICH6_GCS(0x3410). */
+ /* Get the Memory-Mapped GCS register, we need it for the
+ NO_REBOOT flag (TCO v2). To get access to it you have to
+ read RCBA from PCI Config space 0xf0 and use it as base.
+ GCS = RCBA + ICH6_GCS(0x3410). */
if (iTCO_wdt_private.iTCO_version == 2) {
pci_read_config_dword(pdev, 0xf0, &base_address);
RCBA = base_address & 0xffffc000;
- iTCO_wdt_private.gcs = ioremap((RCBA + 0x3410),4);
+ iTCO_wdt_private.gcs = ioremap((RCBA + 0x3410), 4);
}
/* Check chipset's NO_REBOOT bit */
/* Set the TCO_EN bit in SMI_EN register */
if (!request_region(SMI_EN, 4, "iTCO_wdt")) {
- printk(KERN_ERR PFX "I/O address 0x%04lx already in use\n",
- SMI_EN );
+ printk(KERN_ERR PFX
+ "I/O address 0x%04lx already in use\n", SMI_EN);
ret = -EIO;
goto out;
}
outl(val32, SMI_EN);
release_region(SMI_EN, 4);
- /* The TCO I/O registers reside in a 32-byte range pointed to by the TCOBASE value */
- if (!request_region (TCOBASE, 0x20, "iTCO_wdt")) {
- printk (KERN_ERR PFX "I/O address 0x%04lx already in use\n",
+ /* The TCO I/O registers reside in a 32-byte range pointed to
+ by the TCOBASE value */
+ if (!request_region(TCOBASE, 0x20, "iTCO_wdt")) {
+ printk(KERN_ERR PFX "I/O address 0x%04lx already in use\n",
TCOBASE);
ret = -EIO;
goto out;
}
- printk(KERN_INFO PFX "Found a %s TCO device (Version=%d, TCOBASE=0x%04lx)\n",
- iTCO_chipset_info[ent->driver_data].name,
- iTCO_chipset_info[ent->driver_data].iTCO_version,
- TCOBASE);
+ printk(KERN_INFO PFX
+ "Found a %s TCO device (Version=%d, TCOBASE=0x%04lx)\n",
+ iTCO_chipset_info[ent->driver_data].name,
+ iTCO_chipset_info[ent->driver_data].iTCO_version,
+ TCOBASE);
/* Clear out the (probably old) status */
outb(0, TCO1_STS);
/* Make sure the watchdog is not running */
iTCO_wdt_stop();
- /* Check that the heartbeat value is within it's range ; if not reset to the default */
+ /* Check that the heartbeat value is within it's range;
+ if not reset to the default */
if (iTCO_wdt_set_heartbeat(heartbeat)) {
iTCO_wdt_set_heartbeat(WATCHDOG_HEARTBEAT);
- printk(KERN_INFO PFX "heartbeat value must be 2<heartbeat<39 (TCO v1) or 613 (TCO v2), using %d\n",
- heartbeat);
+ printk(KERN_INFO PFX "heartbeat value must be 2 < heartbeat < 39 (TCO v1) or 613 (TCO v2), using %d\n",
+ heartbeat);
}
ret = misc_register(&iTCO_wdt_miscdev);
if (ret != 0) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_region;
}
- printk (KERN_INFO PFX "initialized. heartbeat=%d sec (nowayout=%d)\n",
- heartbeat, nowayout);
+ printk(KERN_INFO PFX "initialized. heartbeat=%d sec (nowayout=%d)\n",
+ heartbeat, nowayout);
return 0;
unreg_region:
- release_region (TCOBASE, 0x20);
+ release_region(TCOBASE, 0x20);
out:
if (iTCO_wdt_private.iTCO_version == 2)
iounmap(iTCO_wdt_private.gcs);
if (err)
return err;
- iTCO_wdt_platform_device = platform_device_register_simple(DRV_NAME, -1, NULL, 0);
+ iTCO_wdt_platform_device = platform_device_register_simple(DRV_NAME,
+ -1, NULL, 0);
if (IS_ERR(iTCO_wdt_platform_device)) {
err = PTR_ERR(iTCO_wdt_platform_device);
goto unreg_platform_driver;
#include <linux/spinlock.h>
#include <linux/moduleparam.h>
#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
static struct platform_device *ibwdt_platform_device;
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Watchdog Operations
*/
-static void
-ibwdt_ping(void)
+static void ibwdt_ping(void)
{
spin_lock(&ibwdt_lock);
spin_unlock(&ibwdt_lock);
}
-static void
-ibwdt_disable(void)
+static void ibwdt_disable(void)
{
spin_lock(&ibwdt_lock);
outb_p(0, WDT_STOP);
spin_unlock(&ibwdt_lock);
}
-static int
-ibwdt_set_heartbeat(int t)
+static int ibwdt_set_heartbeat(int t)
{
int i;
* /dev/watchdog handling
*/
-static ssize_t
-ibwdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t ibwdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
return count;
}
-static int
-ibwdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long ibwdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int new_margin;
void __user *argp = (void __user *)arg;
int __user *p = argp;
static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "IB700 WDT",
};
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof(ident)))
- return -EFAULT;
- break;
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- ibwdt_ping();
- break;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_margin, p))
- return -EFAULT;
- if (ibwdt_set_heartbeat(new_margin))
- return -EINVAL;
- ibwdt_ping();
- /* Fall */
-
- case WDIOC_GETTIMEOUT:
- return put_user(wd_times[wd_margin], p);
+ return put_user(0, p);
case WDIOC_SETOPTIONS:
{
- int options, retval = -EINVAL;
+ int options, retval = -EINVAL;
- if (get_user(options, p))
- return -EFAULT;
+ if (get_user(options, p))
+ return -EFAULT;
- if (options & WDIOS_DISABLECARD) {
- ibwdt_disable();
- retval = 0;
- }
+ if (options & WDIOS_DISABLECARD) {
+ ibwdt_disable();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ ibwdt_ping();
+ retval = 0;
+ }
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ ibwdt_ping();
+ break;
- if (options & WDIOS_ENABLECARD) {
- ibwdt_ping();
- retval = 0;
- }
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_margin, p))
+ return -EFAULT;
+ if (ibwdt_set_heartbeat(new_margin))
+ return -EINVAL;
+ ibwdt_ping();
+ /* Fall */
- return retval;
- }
+ case WDIOC_GETTIMEOUT:
+ return put_user(wd_times[wd_margin], p);
default:
- return -ENOTTY;
+ return -ENOTTY;
}
return 0;
}
-static int
-ibwdt_open(struct inode *inode, struct file *file)
+static int ibwdt_open(struct inode *inode, struct file *file)
{
- if (test_and_set_bit(0, &ibwdt_is_open)) {
+ if (test_and_set_bit(0, &ibwdt_is_open))
return -EBUSY;
- }
if (nowayout)
__module_get(THIS_MODULE);
return nonseekable_open(inode, file);
}
-static int
-ibwdt_close(struct inode *inode, struct file *file)
+static int ibwdt_close(struct inode *inode, struct file *file)
{
if (expect_close == 42) {
ibwdt_disable();
} else {
- printk(KERN_CRIT PFX "WDT device closed unexpectedly. WDT will not stop!\n");
+ printk(KERN_CRIT PFX
+ "WDT device closed unexpectedly. WDT will not stop!\n");
ibwdt_ping();
}
clear_bit(0, &ibwdt_is_open);
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = ibwdt_write,
- .ioctl = ibwdt_ioctl,
+ .unlocked_ioctl = ibwdt_ioctl,
.open = ibwdt_open,
.release = ibwdt_close,
};
#if WDT_START != WDT_STOP
if (!request_region(WDT_STOP, 1, "IB700 WDT")) {
- printk (KERN_ERR PFX "STOP method I/O %X is not available.\n", WDT_STOP);
+ printk(KERN_ERR PFX "STOP method I/O %X is not available.\n",
+ WDT_STOP);
res = -EIO;
goto out_nostopreg;
}
#endif
if (!request_region(WDT_START, 1, "IB700 WDT")) {
- printk (KERN_ERR PFX "START method I/O %X is not available.\n", WDT_START);
+ printk(KERN_ERR PFX "START method I/O %X is not available.\n",
+ WDT_START);
res = -EIO;
goto out_nostartreg;
}
res = misc_register(&ibwdt_miscdev);
if (res) {
- printk (KERN_ERR PFX "failed to register misc device\n");
+ printk(KERN_ERR PFX "failed to register misc device\n");
goto out_nomisc;
}
return 0;
static int __devexit ibwdt_remove(struct platform_device *dev)
{
misc_deregister(&ibwdt_miscdev);
- release_region(WDT_START,1);
+ release_region(WDT_START, 1);
#if WDT_START != WDT_STOP
- release_region(WDT_STOP,1);
+ release_region(WDT_STOP, 1);
#endif
return 0;
}
{
int err;
- printk(KERN_INFO PFX "WDT driver for IB700 single board computer initialising.\n");
+ printk(KERN_INFO PFX
+ "WDT driver for IB700 single board computer initialising.\n");
err = platform_driver_register(&ibwdt_driver);
if (err)
return err;
- ibwdt_platform_device = platform_device_register_simple(DRV_NAME, -1, NULL, 0);
+ ibwdt_platform_device = platform_device_register_simple(DRV_NAME,
+ -1, NULL, 0);
if (IS_ERR(ibwdt_platform_device)) {
err = PTR_ERR(ibwdt_platform_device);
goto unreg_platform_driver;
#include <linux/miscdevice.h>
#include <linux/watchdog.h>
#include <linux/dmi.h>
-
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
enum {
static unsigned int asr_type, asr_base, asr_length;
static unsigned int asr_read_addr, asr_write_addr;
static unsigned char asr_toggle_mask, asr_disable_mask;
+static spinlock_t asr_lock;
-static void asr_toggle(void)
+static void __asr_toggle(void)
{
- unsigned char reg = inb(asr_read_addr);
+ unsigned char reg;
+
+ reg = inb(asr_read_addr);
outb(reg & ~asr_toggle_mask, asr_write_addr);
reg = inb(asr_read_addr);
outb(reg & ~asr_toggle_mask, asr_write_addr);
reg = inb(asr_read_addr);
+ spin_unlock(&asr_lock);
+}
+
+static void asr_toggle(void)
+{
+ spin_lock(&asr_lock);
+ __asr_toggle();
+ spin_unlock(&asr_lock);
}
static void asr_enable(void)
{
unsigned char reg;
+ spin_lock(&asr_lock);
if (asr_type == ASMTYPE_TOPAZ) {
/* asr_write_addr == asr_read_addr */
reg = inb(asr_read_addr);
* First make sure the hardware timer is reset by toggling
* ASR hardware timer line.
*/
- asr_toggle();
+ __asr_toggle();
reg = inb(asr_read_addr);
outb(reg & ~asr_disable_mask, asr_write_addr);
}
reg = inb(asr_read_addr);
+ spin_unlock(&asr_lock);
}
static void asr_disable(void)
{
- unsigned char reg = inb(asr_read_addr);
+ unsigned char reg;
+
+ spin_lock(&asr_lock);
+ reg = inb(asr_read_addr);
if (asr_type == ASMTYPE_TOPAZ)
/* asr_write_addr == asr_read_addr */
outb(reg | asr_disable_mask, asr_write_addr);
}
reg = inb(asr_read_addr);
+ spin_unlock(&asr_lock);
}
static int __init asr_get_base_address(void)
switch (asr_type) {
case ASMTYPE_TOPAZ:
- /* SELECT SuperIO CHIP FOR QUERYING (WRITE 0x07 TO BOTH 0x2E and 0x2F) */
+ /* SELECT SuperIO CHIP FOR QUERYING
+ (WRITE 0x07 TO BOTH 0x2E and 0x2F) */
outb(0x07, 0x2e);
outb(0x07, 0x2f);
case ASMTYPE_JASPER:
type = "Jaspers ";
-
- /* FIXME: need to use pci_config_lock here, but it's not exported */
+#if 0
+ u32 r;
+ /* Suggested fix */
+ pdev = pci_get_bus_and_slot(0, DEVFN(0x1f, 0));
+ if (pdev == NULL)
+ return -ENODEV;
+ pci_read_config_dword(pdev, 0x58, &r);
+ asr_base = r & 0xFFFE;
+ pci_dev_put(pdev);
+#else
+ /* FIXME: need to use pci_config_lock here,
+ but it's not exported */
/* spin_lock_irqsave(&pci_config_lock, flags);*/
/* Select the SuperIO chip in the PCI I/O port register */
outl(0x8000f858, 0xcf8);
+ /* BUS 0, Slot 1F, fnc 0, offset 58 */
+
/*
* Read the base address for the SuperIO chip.
* Only the lower 16 bits are valid, but the address is word
asr_base = inl(0xcfc) & 0xfffe;
/* spin_unlock_irqrestore(&pci_config_lock, flags);*/
-
+#endif
asr_read_addr = asr_write_addr =
asr_base + JASPER_ASR_REG_OFFSET;
asr_toggle_mask = JASPER_ASR_TOGGLE_MASK;
return count;
}
-static int asr_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long asr_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
static const struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING |
+ .options = WDIOF_KEEPALIVEPING |
WDIOF_MAGICCLOSE,
- .identity = "IBM ASR"
+ .identity = "IBM ASR",
};
void __user *argp = (void __user *)arg;
int __user *p = argp;
int heartbeat;
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident)) ?
- -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ {
+ int new_options, retval = -EINVAL;
+ if (get_user(new_options, p))
+ return -EFAULT;
+ if (new_options & WDIOS_DISABLECARD) {
+ asr_disable();
+ retval = 0;
+ }
+ if (new_options & WDIOS_ENABLECARD) {
+ asr_enable();
asr_toggle();
- return 0;
-
- /*
- * The hardware has a fixed timeout value, so no WDIOC_SETTIMEOUT
- * and WDIOC_GETTIMEOUT always returns 256.
- */
- case WDIOC_GETTIMEOUT:
- heartbeat = 256;
- return put_user(heartbeat, p);
-
- case WDIOC_SETOPTIONS: {
- int new_options, retval = -EINVAL;
-
- if (get_user(new_options, p))
- return -EFAULT;
-
- if (new_options & WDIOS_DISABLECARD) {
- asr_disable();
- retval = 0;
- }
-
- if (new_options & WDIOS_ENABLECARD) {
- asr_enable();
- asr_toggle();
- retval = 0;
- }
-
- return retval;
+ retval = 0;
}
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ asr_toggle();
+ return 0;
+ /*
+ * The hardware has a fixed timeout value, so no WDIOC_SETTIMEOUT
+ * and WDIOC_GETTIMEOUT always returns 256.
+ */
+ case WDIOC_GETTIMEOUT:
+ heartbeat = 256;
+ return put_user(heartbeat, p);
+ default:
+ return -ENOTTY;
}
-
- return -ENOTTY;
}
static int asr_open(struct inode *inode, struct file *file)
{
- if(test_and_set_bit(0, &asr_is_open))
+ if (test_and_set_bit(0, &asr_is_open))
return -EBUSY;
asr_toggle();
if (asr_expect_close == 42)
asr_disable();
else {
- printk(KERN_CRIT PFX "unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "unexpected close, not stopping watchdog!\n");
asr_toggle();
}
clear_bit(0, &asr_is_open);
}
static const struct file_operations asr_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = asr_write,
- .ioctl = asr_ioctl,
- .open = asr_open,
- .release = asr_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = asr_write,
+ .unlocked_ioctl = asr_ioctl,
+ .open = asr_open,
+ .release = asr_release,
};
static struct miscdevice asr_miscdev = {
if (!asr_type)
return -ENODEV;
+ spin_lock_init(&asr_lock);
+
rc = asr_get_base_address();
if (rc)
return rc;
module_exit(ibmasr_exit);
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
MODULE_DESCRIPTION("IBM Automatic Server Restart driver");
MODULE_AUTHOR("Andrey Panin");
/*
* IndyDog 0.3 A Hardware Watchdog Device for SGI IP22
*
- * (c) Copyright 2002 Guido Guenther <agx@sigxcpu.org>, All Rights Reserved.
+ * (c) Copyright 2002 Guido Guenther <agx@sigxcpu.org>,
+ * All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#include <asm/sgi/mc.h>
#define PFX "indydog: "
-static int indydog_alive;
+static unsigned long indydog_alive;
+static spinlock_t indydog_lock;
#define WATCHDOG_TIMEOUT 30 /* 30 sec default timeout */
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static void indydog_start(void)
{
- u32 mc_ctrl0 = sgimc->cpuctrl0;
+ u32 mc_ctrl0;
+ spin_lock(&indydog_lock);
+ mc_ctrl0 = sgimc->cpuctrl0;
mc_ctrl0 = sgimc->cpuctrl0 | SGIMC_CCTRL0_WDOG;
sgimc->cpuctrl0 = mc_ctrl0;
+ spin_unlock(&indydog_lock);
}
static void indydog_stop(void)
{
- u32 mc_ctrl0 = sgimc->cpuctrl0;
+ u32 mc_ctrl0;
+ spin_lock(&indydog_lock);
+
+ mc_ctrl0 = sgimc->cpuctrl0;
mc_ctrl0 &= ~SGIMC_CCTRL0_WDOG;
sgimc->cpuctrl0 = mc_ctrl0;
+ spin_unlock(&indydog_lock);
printk(KERN_INFO PFX "Stopped watchdog timer.\n");
}
*/
static int indydog_open(struct inode *inode, struct file *file)
{
- if (indydog_alive)
+ if (test_and_set_bit(0, &indydog_alive))
return -EBUSY;
if (nowayout)
* Lock it in if it's a module and we defined ...NOWAYOUT */
if (!nowayout)
indydog_stop(); /* Turn the WDT off */
-
- indydog_alive = 0;
-
+ clear_bit(0, &indydog_alive);
return 0;
}
-static ssize_t indydog_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t indydog_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
/* Refresh the timer. */
- if (len) {
+ if (len)
indydog_ping();
- }
return len;
}
-static int indydog_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long indydog_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int options, retval = -EINVAL;
static struct watchdog_info ident = {
};
switch (cmd) {
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- if (copy_to_user((struct watchdog_info *)arg,
- &ident, sizeof(ident)))
- return -EFAULT;
- return 0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0,(int *)arg);
- case WDIOC_KEEPALIVE:
- indydog_ping();
- return 0;
- case WDIOC_GETTIMEOUT:
- return put_user(WATCHDOG_TIMEOUT,(int *)arg);
- case WDIOC_SETOPTIONS:
- {
- if (get_user(options, (int *)arg))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- indydog_stop();
- retval = 0;
- }
-
- if (options & WDIOS_ENABLECARD) {
- indydog_start();
- retval = 0;
- }
-
- return retval;
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user((struct watchdog_info *)arg,
+ &ident, sizeof(ident)))
+ return -EFAULT;
+ return 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, (int *)arg);
+ case WDIOC_SETOPTIONS:
+ {
+ if (get_user(options, (int *)arg))
+ return -EFAULT;
+ if (options & WDIOS_DISABLECARD) {
+ indydog_stop();
+ retval = 0;
}
+ if (options & WDIOS_ENABLECARD) {
+ indydog_start();
+ retval = 0;
+ }
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ indydog_ping();
+ return 0;
+ case WDIOC_GETTIMEOUT:
+ return put_user(WATCHDOG_TIMEOUT, (int *)arg);
+ default:
+ return -ENOTTY;
}
}
-static int indydog_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int indydog_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
if (code == SYS_DOWN || code == SYS_HALT)
indydog_stop(); /* Turn the WDT off */
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = indydog_write,
- .ioctl = indydog_ioctl,
+ .unlocked_ioctl = indydog_ioctl,
.open = indydog_open,
.release = indydog_release,
};
{
int ret;
+ spin_lock_init(&indydog_lock);
+
ret = register_reboot_notifier(&indydog_notifier);
if (ret) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
return ret;
}
ret = misc_register(&indydog_miscdev);
if (ret) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
unregister_reboot_notifier(&indydog_notifier);
return ret;
}
#include <linux/miscdevice.h>
#include <linux/watchdog.h>
#include <linux/uaccess.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
static int nowayout = WATCHDOG_NOWAYOUT;
static unsigned long wdt_status;
static unsigned long boot_status;
+static spinlock_t wdt_lock;
#define WDT_IN_USE 0
#define WDT_OK_TO_CLOSE 1
/* Arm and enable the Timer to starting counting down from 0xFFFF.FFFF
* Takes approx. 10.7s to timeout
*/
+ spin_lock(&wdt_lock);
write_wdtcr(IOP_WDTCR_EN_ARM);
write_wdtcr(IOP_WDTCR_EN);
+ spin_unlock(&wdt_lock);
}
/* returns 0 if the timer was successfully disabled */
{
/* Stop Counting */
if (wdt_supports_disable()) {
+ spin_lock(&wdt_lock);
write_wdtcr(IOP_WDTCR_DIS_ARM);
write_wdtcr(IOP_WDTCR_DIS);
clear_bit(WDT_ENABLED, &wdt_status);
+ spin_unlock(&wdt_lock);
printk(KERN_INFO "WATCHDOG: Disabled\n");
return 0;
} else
return -EBUSY;
clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
-
wdt_enable();
-
set_bit(WDT_ENABLED, &wdt_status);
-
return nonseekable_open(inode, file);
}
-static ssize_t
-iop_wdt_write(struct file *file, const char *data, size_t len,
+static ssize_t iop_wdt_write(struct file *file, const char *data, size_t len,
loff_t *ppos)
{
if (len) {
}
wdt_enable();
}
-
return len;
}
-static struct watchdog_info ident = {
+static const struct watchdog_info ident = {
.options = WDIOF_CARDRESET | WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING,
.identity = "iop watchdog",
};
-static int
-iop_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long iop_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int options;
int ret = -ENOTTY;
+ int __user *argp = (int __user *)arg;
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user
- ((struct watchdog_info *)arg, &ident, sizeof ident))
+ if (copy_to_user(argp, &ident, sizeof ident))
ret = -EFAULT;
else
ret = 0;
break;
case WDIOC_GETSTATUS:
- ret = put_user(0, (int *)arg);
+ ret = put_user(0, argp);
break;
case WDIOC_GETBOOTSTATUS:
- ret = put_user(boot_status, (int *)arg);
- break;
-
- case WDIOC_GETTIMEOUT:
- ret = put_user(iop_watchdog_timeout(), (int *)arg);
- break;
-
- case WDIOC_KEEPALIVE:
- wdt_enable();
- ret = 0;
+ ret = put_user(boot_status, argp);
break;
case WDIOC_SETOPTIONS:
} else
ret = 0;
}
-
if (options & WDIOS_ENABLECARD) {
wdt_enable();
ret = 0;
}
break;
- }
+ case WDIOC_KEEPALIVE:
+ wdt_enable();
+ ret = 0;
+ break;
+
+ case WDIOC_GETTIMEOUT:
+ ret = put_user(iop_watchdog_timeout(), argp);
+ break;
+ }
return ret;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = iop_wdt_write,
- .ioctl = iop_wdt_ioctl,
+ .unlocked_ioctl = iop_wdt_ioctl,
.open = iop_wdt_open,
.release = iop_wdt_release,
};
{
int ret;
- ret = misc_register(&iop_wdt_miscdev);
- if (ret == 0)
- printk("iop watchdog timer: timeout %lu sec\n",
- iop_watchdog_timeout());
+ spin_lock_init(&wdt_lock);
+
/* check if the reset was caused by the watchdog timer */
boot_status = (read_rcsr() & IOP_RCSR_WDT) ? WDIOF_CARDRESET : 0;
*/
write_wdtsr(IOP13XX_WDTCR_IB_RESET);
+ /* Register after we have the device set up so we cannot race
+ with an open */
+ ret = misc_register(&iop_wdt_miscdev);
+ if (ret == 0)
+ printk(KERN_INFO "iop watchdog timer: timeout %lu sec\n",
+ iop_watchdog_timeout());
+
return ret;
}
#include <linux/fs.h>
#include <linux/pci.h>
#include <linux/spinlock.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#define NAME "it8712f_wdt"
module_param(nowayout, int, 0);
MODULE_PARM_DESC(nowayout, "Disable watchdog shutdown on close");
-static struct semaphore it8712f_wdt_sem;
+static unsigned long wdt_open;
static unsigned expect_close;
static spinlock_t io_lock;
static unsigned char revision;
#define WDT_OUT_PWROK 0x10
#define WDT_OUT_KRST 0x40
-static int
-superio_inb(int reg)
+static int superio_inb(int reg)
{
outb(reg, REG);
return inb(VAL);
}
-static void
-superio_outb(int val, int reg)
+static void superio_outb(int val, int reg)
{
outb(reg, REG);
outb(val, VAL);
}
-static int
-superio_inw(int reg)
+static int superio_inw(int reg)
{
int val;
outb(reg++, REG);
return val;
}
-static inline void
-superio_select(int ldn)
+static inline void superio_select(int ldn)
{
outb(LDN, REG);
outb(ldn, VAL);
}
-static inline void
-superio_enter(void)
+static inline void superio_enter(void)
{
spin_lock(&io_lock);
outb(0x87, REG);
outb(0x55, REG);
}
-static inline void
-superio_exit(void)
+static inline void superio_exit(void)
{
outb(0x02, REG);
outb(0x02, VAL);
spin_unlock(&io_lock);
}
-static inline void
-it8712f_wdt_ping(void)
+static inline void it8712f_wdt_ping(void)
{
inb(address);
}
-static void
-it8712f_wdt_update_margin(void)
+static void it8712f_wdt_update_margin(void)
{
int config = WDT_OUT_KRST | WDT_OUT_PWROK;
int units = margin;
superio_outb(units, WDT_TIMEOUT);
}
-static int
-it8712f_wdt_get_status(void)
+static int it8712f_wdt_get_status(void)
{
if (superio_inb(WDT_CONTROL) & 0x01)
return WDIOF_CARDRESET;
return 0;
}
-static void
-it8712f_wdt_enable(void)
+static void it8712f_wdt_enable(void)
{
printk(KERN_DEBUG NAME ": enabling watchdog timer\n");
superio_enter();
it8712f_wdt_ping();
}
-static void
-it8712f_wdt_disable(void)
+static void it8712f_wdt_disable(void)
{
printk(KERN_DEBUG NAME ": disabling watchdog timer\n");
superio_exit();
}
-static int
-it8712f_wdt_notify(struct notifier_block *this,
+static int it8712f_wdt_notify(struct notifier_block *this,
unsigned long code, void *unused)
{
if (code == SYS_HALT || code == SYS_POWER_OFF)
.notifier_call = it8712f_wdt_notify,
};
-static ssize_t
-it8712f_wdt_write(struct file *file, const char __user *data,
- size_t len, loff_t *ppos)
+static ssize_t it8712f_wdt_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
/* check for a magic close character */
if (len) {
expect_close = 0;
for (i = 0; i < len; ++i) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
return len;
}
-static int
-it8712f_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long it8712f_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int value;
switch (cmd) {
- default:
- return -ENOTTY;
case WDIOC_GETSUPPORT:
if (copy_to_user(argp, &ident, sizeof(ident)))
return -EFAULT;
if (put_user(margin, p))
return -EFAULT;
return 0;
+ default:
+ return -ENOTTY;
}
}
-static int
-it8712f_wdt_open(struct inode *inode, struct file *file)
+static int it8712f_wdt_open(struct inode *inode, struct file *file)
{
/* only allow one at a time */
- if (down_trylock(&it8712f_wdt_sem))
+ if (test_and_set_bit(0, &wdt_open))
return -EBUSY;
it8712f_wdt_enable();
-
return nonseekable_open(inode, file);
}
-static int
-it8712f_wdt_release(struct inode *inode, struct file *file)
+static int it8712f_wdt_release(struct inode *inode, struct file *file)
{
if (expect_close != 42) {
printk(KERN_WARNING NAME
it8712f_wdt_disable();
}
expect_close = 0;
- up(&it8712f_wdt_sem);
+ clear_bit(0, &wdt_open);
return 0;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = it8712f_wdt_write,
- .ioctl = it8712f_wdt_ioctl,
+ .unlocked_ioctl = it8712f_wdt_ioctl,
.open = it8712f_wdt_open,
.release = it8712f_wdt_release,
};
.fops = &it8712f_wdt_fops,
};
-static int __init
-it8712f_wdt_find(unsigned short *address)
+static int __init it8712f_wdt_find(unsigned short *address)
{
int err = -ENODEV;
int chip_type;
return err;
}
-static int __init
-it8712f_wdt_init(void)
+static int __init it8712f_wdt_init(void)
{
int err = 0;
it8712f_wdt_disable();
- sema_init(&it8712f_wdt_sem, 1);
-
err = register_reboot_notifier(&it8712f_wdt_notifier);
if (err) {
printk(KERN_ERR NAME ": unable to register reboot notifier\n");
return err;
}
-static void __exit
-it8712f_wdt_exit(void)
+static void __exit it8712f_wdt_exit(void)
{
misc_deregister(&it8712f_wdt_miscdev);
unregister_reboot_notifier(&it8712f_wdt_notifier);
#include <linux/watchdog.h>
#include <linux/init.h>
#include <linux/bitops.h>
-
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
+#include <mach/hardware.h>
static int nowayout = WATCHDOG_NOWAYOUT;
static unsigned int heartbeat = 60; /* (secs) Default is 1 minute */
static unsigned long wdt_status;
+static spinlock_t wdt_lock;
#define WDT_IN_USE 0
#define WDT_OK_TO_CLOSE 1
static unsigned long wdt_tick_rate;
-static void
-wdt_enable(void)
+static void wdt_enable(void)
{
+ spin_lock(&wdt_lock);
ixp2000_reg_write(IXP2000_RESET0, *(IXP2000_RESET0) | WDT_RESET_ENABLE);
ixp2000_reg_write(IXP2000_TWDE, WDT_ENABLE);
ixp2000_reg_write(IXP2000_T4_CLD, heartbeat * wdt_tick_rate);
ixp2000_reg_write(IXP2000_T4_CTL, TIMER_DIVIDER_256 | TIMER_ENABLE);
+ spin_unlock(&wdt_lock);
}
-static void
-wdt_disable(void)
+static void wdt_disable(void)
{
+ spin_lock(&wdt_lock);
ixp2000_reg_write(IXP2000_T4_CTL, 0);
+ spin_unlock(&wdt_lock);
}
-static void
-wdt_keepalive(void)
+static void wdt_keepalive(void)
{
+ spin_lock(&wdt_lock);
ixp2000_reg_write(IXP2000_T4_CLD, heartbeat * wdt_tick_rate);
+ spin_unlock(&wdt_lock);
}
-static int
-ixp2000_wdt_open(struct inode *inode, struct file *file)
+static int ixp2000_wdt_open(struct inode *inode, struct file *file)
{
if (test_and_set_bit(WDT_IN_USE, &wdt_status))
return -EBUSY;
return nonseekable_open(inode, file);
}
-static ssize_t
-ixp2000_wdt_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t ixp2000_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
if (len) {
if (!nowayout) {
.identity = "IXP2000 Watchdog",
};
-static int
-ixp2000_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long ixp2000_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int ret = -ENOTTY;
int time;
ret = put_user(0, (int *)arg);
break;
+ case WDIOC_KEEPALIVE:
+ wdt_enable();
+ ret = 0;
+ break;
+
case WDIOC_SETTIMEOUT:
ret = get_user(time, (int *)arg);
if (ret)
case WDIOC_GETTIMEOUT:
ret = put_user(heartbeat, (int *)arg);
break;
-
- case WDIOC_KEEPALIVE:
- wdt_enable();
- ret = 0;
- break;
}
return ret;
}
-static int
-ixp2000_wdt_release(struct inode *inode, struct file *file)
+static int ixp2000_wdt_release(struct inode *inode, struct file *file)
{
- if (test_bit(WDT_OK_TO_CLOSE, &wdt_status)) {
+ if (test_bit(WDT_OK_TO_CLOSE, &wdt_status))
wdt_disable();
- } else {
+ else
printk(KERN_CRIT "WATCHDOG: Device closed unexpectedly - "
"timer will not stop\n");
- }
-
clear_bit(WDT_IN_USE, &wdt_status);
clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
}
-static const struct file_operations ixp2000_wdt_fops =
-{
+static const struct file_operations ixp2000_wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = ixp2000_wdt_write,
- .ioctl = ixp2000_wdt_ioctl,
+ .unlocked_ioctl = ixp2000_wdt_ioctl,
.open = ixp2000_wdt_open,
.release = ixp2000_wdt_release,
};
-static struct miscdevice ixp2000_wdt_miscdev =
-{
+static struct miscdevice ixp2000_wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &ixp2000_wdt_fops,
printk(KERN_INFO "Unable to use IXP2000 watchdog due to IXP2800 erratum #25.\n");
return -EIO;
}
-
wdt_tick_rate = (*IXP2000_T1_CLD * HZ) / 256;
-
+ spin_lock_init(&wdt_lock);
return misc_register(&ixp2000_wdt_miscdev);
}
#include <linux/watchdog.h>
#include <linux/init.h>
#include <linux/bitops.h>
-
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
+#include <mach/hardware.h>
static int nowayout = WATCHDOG_NOWAYOUT;
static int heartbeat = 60; /* (secs) Default is 1 minute */
static unsigned long wdt_status;
static unsigned long boot_status;
+static spin_lock_t wdt_lock;
#define WDT_TICK_RATE (IXP4XX_PERIPHERAL_BUS_CLOCK * 1000000UL)
#define WDT_IN_USE 0
#define WDT_OK_TO_CLOSE 1
-static void
-wdt_enable(void)
+static void wdt_enable(void)
{
+ spin_lock(&wdt_lock);
*IXP4XX_OSWK = IXP4XX_WDT_KEY;
*IXP4XX_OSWE = 0;
*IXP4XX_OSWT = WDT_TICK_RATE * heartbeat;
*IXP4XX_OSWE = IXP4XX_WDT_COUNT_ENABLE | IXP4XX_WDT_RESET_ENABLE;
*IXP4XX_OSWK = 0;
+ spin_unlock(&wdt_lock);
}
-static void
-wdt_disable(void)
+static void wdt_disable(void)
{
+ spin_lock(&wdt_lock);
*IXP4XX_OSWK = IXP4XX_WDT_KEY;
*IXP4XX_OSWE = 0;
*IXP4XX_OSWK = 0;
+ spin_unlock(&wdt_lock);
}
-static int
-ixp4xx_wdt_open(struct inode *inode, struct file *file)
+static int ixp4xx_wdt_open(struct inode *inode, struct file *file)
{
if (test_and_set_bit(WDT_IN_USE, &wdt_status))
return -EBUSY;
clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
-
wdt_enable();
-
return nonseekable_open(inode, file);
}
}
wdt_enable();
}
-
return len;
}
};
-static int
-ixp4xx_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long ixp4xx_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int ret = -ENOTTY;
int time;
ret = put_user(boot_status, (int *)arg);
break;
+ case WDIOC_KEEPALIVE:
+ wdt_enable();
+ ret = 0;
+ break;
+
case WDIOC_SETTIMEOUT:
ret = get_user(time, (int *)arg);
if (ret)
case WDIOC_GETTIMEOUT:
ret = put_user(heartbeat, (int *)arg);
break;
-
- case WDIOC_KEEPALIVE:
- wdt_enable();
- ret = 0;
- break;
}
return ret;
}
-static int
-ixp4xx_wdt_release(struct inode *inode, struct file *file)
+static int ixp4xx_wdt_release(struct inode *inode, struct file *file)
{
- if (test_bit(WDT_OK_TO_CLOSE, &wdt_status)) {
+ if (test_bit(WDT_OK_TO_CLOSE, &wdt_status))
wdt_disable();
- } else {
+ else
printk(KERN_CRIT "WATCHDOG: Device closed unexpectedly - "
"timer will not stop\n");
- }
-
clear_bit(WDT_IN_USE, &wdt_status);
clear_bit(WDT_OK_TO_CLOSE, &wdt_status);
}
-static const struct file_operations ixp4xx_wdt_fops =
-{
+static const struct file_operations ixp4xx_wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = ixp4xx_wdt_write,
- .ioctl = ixp4xx_wdt_ioctl,
+ .unlocked_ioctl = ixp4xx_wdt_ioctl,
.open = ixp4xx_wdt_open,
.release = ixp4xx_wdt_release,
};
-static struct miscdevice ixp4xx_wdt_miscdev =
-{
+static struct miscdevice ixp4xx_wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &ixp4xx_wdt_fops,
asm("mrc p15, 0, %0, cr0, cr0, 0;" : "=r"(processor_id) :);
if (!(processor_id & 0xf) && !cpu_is_ixp46x()) {
- printk("IXP4XXX Watchdog: Rev. A0 IXP42x CPU detected - "
- "watchdog disabled\n");
+ printk(KERN_ERR "IXP4XXX Watchdog: Rev. A0 IXP42x CPU detected"
+ " - watchdog disabled\n");
return -ENODEV;
}
-
- ret = misc_register(&ixp4xx_wdt_miscdev);
- if (ret == 0)
- printk("IXP4xx Watchdog Timer: heartbeat %d sec\n", heartbeat);
-
+ spin_lock_init(&wdt_lock);
boot_status = (*IXP4XX_OSST & IXP4XX_OSST_TIMER_WARM_RESET) ?
WDIOF_CARDRESET : 0;
-
+ ret = misc_register(&ixp4xx_wdt_miscdev);
+ if (ret == 0)
+ printk(KERN_INFO "IXP4xx Watchdog Timer: heartbeat %d sec\n",
+ heartbeat);
return ret;
}
#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/watchdog.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/arch/regs-timer.h>
-
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <mach/regs-timer.h>
#define WDT_DEFAULT_TIME 5 /* seconds */
#define WDT_MAX_TIME 171 /* seconds */
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(wdt_time, int, 0);
-MODULE_PARM_DESC(wdt_time, "Watchdog time in seconds. (default="__MODULE_STRING(WDT_DEFAULT_TIME) ")");
+MODULE_PARM_DESC(wdt_time, "Watchdog time in seconds. (default="
+ __MODULE_STRING(WDT_DEFAULT_TIME) ")");
#ifdef CONFIG_WATCHDOG_NOWAYOUT
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#endif
static unsigned long ks8695wdt_busy;
+static spinlock_t ks8695_lock;
/* ......................................................................... */
/*
* Disable the watchdog.
*/
-static void inline ks8695_wdt_stop(void)
+static inline void ks8695_wdt_stop(void)
{
unsigned long tmcon;
+ spin_lock(&ks8695_lock);
/* disable timer0 */
tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
__raw_writel(tmcon & ~TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
+ spin_unlock(&ks8695_lock);
}
/*
* Enable and reset the watchdog.
*/
-static void inline ks8695_wdt_start(void)
+static inline void ks8695_wdt_start(void)
{
unsigned long tmcon;
unsigned long tval = wdt_time * CLOCK_TICK_RATE;
+ spin_lock(&ks8695_lock);
/* disable timer0 */
tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
__raw_writel(tmcon & ~TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
/* re-enable timer0 */
tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
__raw_writel(tmcon | TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
+ spin_unlock(&ks8695_lock);
}
/*
* Reload the watchdog timer. (ie, pat the watchdog)
*/
-static void inline ks8695_wdt_reload(void)
+static inline void ks8695_wdt_reload(void)
{
unsigned long tmcon;
+ spin_lock(&ks8695_lock);
/* disable, then re-enable timer0 */
tmcon = __raw_readl(KS8695_TMR_VA + KS8695_TMCON);
__raw_writel(tmcon & ~TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
__raw_writel(tmcon | TMCON_T0EN, KS8695_TMR_VA + KS8695_TMCON);
+ spin_unlock(&ks8695_lock);
}
/*
if ((new_time <= 0) || (new_time > WDT_MAX_TIME))
return -EINVAL;
- /* Set new watchdog time. It will be used when ks8695_wdt_start() is called. */
+ /* Set new watchdog time. It will be used when
+ ks8695_wdt_start() is called. */
wdt_time = new_time;
return 0;
}
*/
static int ks8695_wdt_close(struct inode *inode, struct file *file)
{
+ /* Disable the watchdog when file is closed */
if (!nowayout)
- ks8695_wdt_stop(); /* Disable the watchdog when file is closed */
-
+ ks8695_wdt_stop();
clear_bit(0, &ks8695wdt_busy);
return 0;
}
/*
* Handle commands from user-space.
*/
-static int ks8695_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long ks8695_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_value;
- switch(cmd) {
- case WDIOC_KEEPALIVE:
- ks8695_wdt_reload(); /* pat the watchdog */
- return 0;
-
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ks8695_wdt_info, sizeof(ks8695_wdt_info)) ? -EFAULT : 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_value, p))
- return -EFAULT;
-
- if (ks8695_wdt_settimeout(new_value))
- return -EINVAL;
-
- /* Enable new time value */
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ks8695_wdt_info,
+ sizeof(ks8695_wdt_info)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ if (get_user(new_value, p))
+ return -EFAULT;
+ if (new_value & WDIOS_DISABLECARD)
+ ks8695_wdt_stop();
+ if (new_value & WDIOS_ENABLECARD)
ks8695_wdt_start();
-
- /* Return current value */
- return put_user(wdt_time, p);
-
- case WDIOC_GETTIMEOUT:
- return put_user(wdt_time, p);
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_SETOPTIONS:
- if (get_user(new_value, p))
- return -EFAULT;
-
- if (new_value & WDIOS_DISABLECARD)
- ks8695_wdt_stop();
- if (new_value & WDIOS_ENABLECARD)
- ks8695_wdt_start();
- return 0;
-
- default:
- return -ENOTTY;
+ return 0;
+ case WDIOC_KEEPALIVE:
+ ks8695_wdt_reload(); /* pat the watchdog */
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_value, p))
+ return -EFAULT;
+ if (ks8695_wdt_settimeout(new_value))
+ return -EINVAL;
+ /* Enable new time value */
+ ks8695_wdt_start();
+ /* Return current value */
+ return put_user(wdt_time, p);
+ case WDIOC_GETTIMEOUT:
+ return put_user(wdt_time, p);
+ default:
+ return -ENOTTY;
}
}
/*
* Pat the watchdog whenever device is written to.
*/
-static ssize_t ks8695_wdt_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t ks8695_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
ks8695_wdt_reload(); /* pat the watchdog */
return len;
static const struct file_operations ks8695wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = ks8695_wdt_ioctl,
+ .unlocked_ioctl = ks8695_wdt_ioctl,
.open = ks8695_wdt_open,
.release = ks8695_wdt_close,
.write = ks8695_wdt_write,
if (res)
return res;
- printk("KS8695 Watchdog Timer enabled (%d seconds%s)\n", wdt_time, nowayout ? ", nowayout" : "");
+ printk(KERN_INFO "KS8695 Watchdog Timer enabled (%d seconds%s)\n",
+ wdt_time, nowayout ? ", nowayout" : "");
return 0;
}
static int __init ks8695_wdt_init(void)
{
- /* Check that the heartbeat value is within range; if not reset to the default */
+ spin_lock_init(&ks8695_lock);
+ /* Check that the heartbeat value is within range;
+ if not reset to the default */
if (ks8695_wdt_settimeout(wdt_time)) {
ks8695_wdt_settimeout(WDT_DEFAULT_TIME);
- pr_info("ks8695_wdt: wdt_time value must be 1 <= wdt_time <= %i, using %d\n", wdt_time, WDT_MAX_TIME);
+ pr_info("ks8695_wdt: wdt_time value must be 1 <= wdt_time <= %i, using %d\n",
+ wdt_time, WDT_MAX_TIME);
}
-
return platform_driver_register(&ks8695wdt_driver);
}
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
/* ports */
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#define PFX "machzwd"
* 3 = GEN_SCI
* defaults to GEN_RESET (0)
*/
-static int action = 0;
+static int action;
module_param(action, int, 0);
MODULE_PARM_DESC(action, "after watchdog resets, generate: 0 = RESET(*) 1 = SMI 2 = NMI 3 = SCI");
static int zf_action = GEN_RESET;
static unsigned long zf_is_open;
static char zf_expect_close;
-static DEFINE_SPINLOCK(zf_lock);
static DEFINE_SPINLOCK(zf_port_lock);
static DEFINE_TIMER(zf_timer, zf_ping, 0, 0);
-static unsigned long next_heartbeat = 0;
+static unsigned long next_heartbeat;
/* timeout for user land heart beat (10 seconds) */
static inline void zf_set_timer(unsigned short new, unsigned char n)
{
- switch(n){
- case WD1:
- zf_writew(COUNTER_1, new);
- case WD2:
- zf_writeb(COUNTER_2, new > 0xff ? 0xff : new);
- default:
- return;
+ switch (n) {
+ case WD1:
+ zf_writew(COUNTER_1, new);
+ case WD2:
+ zf_writeb(COUNTER_2, new > 0xff ? 0xff : new);
+ default:
+ return;
}
}
zf_writeb(COUNTER_2, 0xff);
- if(time_before(jiffies, next_heartbeat)){
-
+ if (time_before(jiffies, next_heartbeat)) {
dprintk("time_before: %ld\n", next_heartbeat - jiffies);
-
/*
* reset event is activated by transition from 0 to 1 on
* RESET_WD1 bit and we assume that it is already zero...
spin_unlock_irqrestore(&zf_port_lock, flags);
mod_timer(&zf_timer, jiffies + ZF_HW_TIMEO);
- }else{
+ } else
printk(KERN_CRIT PFX ": I will reset your machine\n");
- }
}
static ssize_t zf_write(struct file *file, const char __user *buf, size_t count,
loff_t *ppos)
{
/* See if we got the magic character */
- if(count){
-
+ if (count) {
/*
* no need to check for close confirmation
* no way to disable watchdog ;)
*/
if (!nowayout) {
size_t ofs;
-
/*
* note: just in case someone wrote the magic character
* five months ago...
zf_expect_close = 0;
/* now scan */
- for (ofs = 0; ofs != count; ofs++){
+ for (ofs = 0; ofs != count; ofs++) {
char c;
if (get_user(c, buf + ofs))
return -EFAULT;
- if (c == 'V'){
+ if (c == 'V') {
zf_expect_close = 42;
dprintk("zf_expect_close = 42\n");
}
*/
next_heartbeat = jiffies + ZF_USER_TIMEO;
dprintk("user ping at %ld\n", jiffies);
-
}
-
return count;
}
-static int zf_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long zf_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
if (copy_to_user(argp, &zf_info, sizeof(zf_info)))
return -EFAULT;
break;
-
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
return put_user(0, p);
-
case WDIOC_KEEPALIVE:
zf_ping(0);
break;
-
default:
return -ENOTTY;
}
-
return 0;
}
static int zf_open(struct inode *inode, struct file *file)
{
- spin_lock(&zf_lock);
- if(test_and_set_bit(0, &zf_is_open)) {
- spin_unlock(&zf_lock);
+ if (test_and_set_bit(0, &zf_is_open))
return -EBUSY;
- }
-
if (nowayout)
__module_get(THIS_MODULE);
-
- spin_unlock(&zf_lock);
-
zf_timer_on();
-
return nonseekable_open(inode, file);
}
static int zf_close(struct inode *inode, struct file *file)
{
- if(zf_expect_close == 42){
+ if (zf_expect_close == 42)
zf_timer_off();
- } else {
+ else {
del_timer(&zf_timer);
printk(KERN_ERR PFX ": device file closed unexpectedly. Will not stop the WDT!\n");
}
-
- spin_lock(&zf_lock);
clear_bit(0, &zf_is_open);
- spin_unlock(&zf_lock);
-
zf_expect_close = 0;
-
return 0;
}
static int zf_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code == SYS_DOWN || code == SYS_HALT){
+ if (code == SYS_DOWN || code == SYS_HALT)
zf_timer_off();
- }
-
return NOTIFY_DONE;
}
-
-
-
static const struct file_operations zf_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = zf_write,
- .ioctl = zf_ioctl,
- .open = zf_open,
- .release = zf_close,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = zf_write,
+ .unlocked_ioctl = zf_ioctl,
+ .open = zf_open,
+ .release = zf_close,
};
static struct miscdevice zf_miscdev = {
.name = "watchdog",
.fops = &zf_fops,
};
-
+
/*
* The device needs to learn about soft shutdowns in order to
{
int ret;
- printk(KERN_INFO PFX ": MachZ ZF-Logic Watchdog driver initializing.\n");
+ printk(KERN_INFO PFX
+ ": MachZ ZF-Logic Watchdog driver initializing.\n");
ret = zf_get_ZFL_version();
- if ((!ret) || (ret == 0xffff)) {
+ if (!ret || ret == 0xffff) {
printk(KERN_WARNING PFX ": no ZF-Logic found\n");
return -ENODEV;
}
- if((action <= 3) && (action >= 0)){
- zf_action = zf_action>>action;
- } else
+ if (action <= 3 && action >= 0)
+ zf_action = zf_action >> action;
+ else
action = 0;
zf_show_action(action);
- if(!request_region(ZF_IOBASE, 3, "MachZ ZFL WDT")){
+ if (!request_region(ZF_IOBASE, 3, "MachZ ZFL WDT")) {
printk(KERN_ERR "cannot reserve I/O ports at %d\n",
ZF_IOBASE);
ret = -EBUSY;
}
ret = register_reboot_notifier(&zf_notifier);
- if(ret){
+ if (ret) {
printk(KERN_ERR "can't register reboot notifier (err=%d)\n",
ret);
goto no_reboot;
}
ret = misc_register(&zf_miscdev);
- if (ret){
+ if (ret) {
printk(KERN_ERR "can't misc_register on minor=%d\n",
WATCHDOG_MINOR);
goto no_misc;
* - support for one more type board
*
* Version 0.5 (2001/12/14) Matt Domsch <Matt_Domsch@dell.com>
- * - added nowayout module option to override CONFIG_WATCHDOG_NOWAYOUT
+ * - added nowayout module option to override
+ * CONFIG_WATCHDOG_NOWAYOUT
*
* Version 0.6 (2002/04/12): Rob Radez <rob@osinvestor.com>
* - make mixcomwd_opened unsigned,
#include <linux/init.h>
#include <linux/jiffies.h>
#include <linux/timer.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
/*
* We have two types of cards that can be probed:
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static void mixcomwd_ping(void)
{
- outb_p(55,watchdog_port);
+ outb_p(55, watchdog_port);
return;
}
static void mixcomwd_timerfun(unsigned long d)
{
mixcomwd_ping();
-
mod_timer(&mixcomwd_timer, jiffies + 5 * HZ);
}
static int mixcomwd_open(struct inode *inode, struct file *file)
{
- if(test_and_set_bit(0,&mixcomwd_opened)) {
+ if (test_and_set_bit(0, &mixcomwd_opened))
return -EBUSY;
- }
+
mixcomwd_ping();
- if (nowayout) {
+ if (nowayout)
/*
* fops_get() code via open() has already done
* a try_module_get() so it is safe to do the
* __module_get().
*/
__module_get(THIS_MODULE);
- } else {
- if(mixcomwd_timer_alive) {
+ else {
+ if (mixcomwd_timer_alive) {
del_timer(&mixcomwd_timer);
- mixcomwd_timer_alive=0;
+ mixcomwd_timer_alive = 0;
}
}
return nonseekable_open(inode, file);
static int mixcomwd_release(struct inode *inode, struct file *file)
{
if (expect_close == 42) {
- if(mixcomwd_timer_alive) {
- printk(KERN_ERR PFX "release called while internal timer alive");
+ if (mixcomwd_timer_alive) {
+ printk(KERN_ERR PFX
+ "release called while internal timer alive");
return -EBUSY;
}
- mixcomwd_timer_alive=1;
+ mixcomwd_timer_alive = 1;
mod_timer(&mixcomwd_timer, jiffies + 5 * HZ);
- } else {
- printk(KERN_CRIT PFX "WDT device closed unexpectedly. WDT will not stop!\n");
- }
+ } else
+ printk(KERN_CRIT PFX
+ "WDT device closed unexpectedly. WDT will not stop!\n");
- clear_bit(0,&mixcomwd_opened);
- expect_close=0;
+ clear_bit(0, &mixcomwd_opened);
+ expect_close = 0;
return 0;
}
-static ssize_t mixcomwd_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
+static ssize_t mixcomwd_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
- if(len)
- {
+ if (len) {
if (!nowayout) {
size_t i;
return len;
}
-static int mixcomwd_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long mixcomwd_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
.identity = "MixCOM watchdog",
};
- switch(cmd)
- {
- case WDIOC_GETSTATUS:
- status=mixcomwd_opened;
- if (!nowayout) {
- status|=mixcomwd_timer_alive;
- }
- if (copy_to_user(p, &status, sizeof(int))) {
- return -EFAULT;
- }
- break;
- case WDIOC_GETBOOTSTATUS:
- if (copy_to_user(p, &status, sizeof(int))) {
- return -EFAULT;
- }
- break;
- case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof(ident))) {
- return -EFAULT;
- }
- break;
- case WDIOC_KEEPALIVE:
- mixcomwd_ping();
- break;
- default:
- return -ENOTTY;
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
+ case WDIOC_GETSTATUS:
+ status = mixcomwd_opened;
+ if (!nowayout)
+ status |= mixcomwd_timer_alive;
+ return put_user(status, p);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ mixcomwd_ping();
+ break;
+ default:
+ return -ENOTTY;
}
return 0;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = mixcomwd_write,
- .ioctl = mixcomwd_ioctl,
+ .unlocked_ioctl = mixcomwd_ioctl,
.open = mixcomwd_open,
.release = mixcomwd_release,
};
{
int id;
- if (!request_region(port, 1, "MixCOM watchdog")) {
+ if (!request_region(port, 1, "MixCOM watchdog"))
return 0;
- }
- id=inb_p(port);
- if (card_id==MIXCOM_ID)
+ id = inb_p(port);
+ if (card_id == MIXCOM_ID)
id &= 0x3f;
- if (id!=card_id) {
+ if (id != card_id) {
release_region(port, 1);
return 0;
}
static int __init mixcomwd_init(void)
{
- int i;
- int ret;
- int found=0;
+ int i, ret, found = 0;
for (i = 0; !found && mixcomwd_io_info[i].ioport != 0; i++) {
if (checkcard(mixcomwd_io_info[i].ioport,
}
if (!found) {
- printk(KERN_ERR PFX "No card detected, or port not available.\n");
+ printk(KERN_ERR PFX
+ "No card detected, or port not available.\n");
return -ENODEV;
}
ret = misc_register(&mixcomwd_miscdev);
- if (ret)
- {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ if (ret) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto error_misc_register_watchdog;
}
- printk(KERN_INFO "MixCOM watchdog driver v%s, watchdog port at 0x%3x\n",
- VERSION, watchdog_port);
+ printk(KERN_INFO
+ "MixCOM watchdog driver v%s, watchdog port at 0x%3x\n",
+ VERSION, watchdog_port);
return 0;
static void __exit mixcomwd_exit(void)
{
if (!nowayout) {
- if(mixcomwd_timer_alive) {
+ if (mixcomwd_timer_alive) {
printk(KERN_WARNING PFX "I quit now, hardware will"
" probably reboot!\n");
del_timer_sync(&mixcomwd_timer);
- mixcomwd_timer_alive=0;
+ mixcomwd_timer_alive = 0;
}
}
misc_deregister(&mixcomwd_miscdev);
- release_region(watchdog_port,1);
+ release_region(watchdog_port, 1);
}
module_init(mixcomwd_init);
#include <linux/io.h>
#include <linux/spinlock.h>
#include <linux/of_platform.h>
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#include <asm/mpc52xx.h>
/* set timeout, with maximum prescaler */
out_be32(&wdt->regs->count, 0x0 | wdt->count);
/* enable watchdog */
- out_be32(&wdt->regs->mode, GPT_MODE_CE | GPT_MODE_WDT | GPT_MODE_MS_TIMER);
+ out_be32(&wdt->regs->mode, GPT_MODE_CE | GPT_MODE_WDT |
+ GPT_MODE_MS_TIMER);
spin_unlock(&wdt->io_lock);
return 0;
{
spin_lock(&wdt->io_lock);
/* writing A5 to OCPW resets the watchdog */
- out_be32(&wdt->regs->mode, 0xA5000000 | (0xffffff & in_be32(&wdt->regs->mode)));
+ out_be32(&wdt->regs->mode, 0xA5000000 |
+ (0xffffff & in_be32(&wdt->regs->mode)));
spin_unlock(&wdt->io_lock);
return 0;
}
.options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
.identity = "mpc5200 watchdog on GPT0",
};
-static int mpc5200_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long mpc5200_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
struct mpc5200_wdt *wdt = file->private_data;
int __user *data = (int __user *)arg;
switch (cmd) {
case WDIOC_GETSUPPORT:
ret = copy_to_user(data, &mpc5200_wdt_info,
- sizeof(mpc5200_wdt_info));
+ sizeof(mpc5200_wdt_info));
if (ret)
ret = -EFAULT;
break;
}
return ret;
}
+
static int mpc5200_wdt_open(struct inode *inode, struct file *file)
{
/* /dev/watchdog can only be opened once */
static const struct file_operations mpc5200_wdt_fops = {
.owner = THIS_MODULE,
.write = mpc5200_wdt_write,
- .ioctl = mpc5200_wdt_ioctl,
+ .unlocked_ioctl = mpc5200_wdt_ioctl,
.open = mpc5200_wdt_open,
.release = mpc5200_wdt_release,
};
/* module operations */
-static int mpc5200_wdt_probe(struct of_device *op, const struct of_device_id *match)
+static int mpc5200_wdt_probe(struct of_device *op,
+ const struct of_device_id *match)
{
struct mpc5200_wdt *wdt;
int err;
return 0;
iounmap(wdt->regs);
- out_release:
+out_release:
release_mem_region(wdt->mem.start, size);
- out_free:
+out_free:
kfree(wdt);
return err;
}
+++ /dev/null
-/*
- * mpc83xx_wdt.c - MPC83xx watchdog userspace interface
- *
- * Authors: Dave Updegraff <dave@cray.org>
- * Kumar Gala <galak@kernel.crashing.org>
- * Attribution: from 83xx_wst: Florian Schirmer <jolt@tuxbox.org>
- * ..and from sc520_wdt
- *
- * Note: it appears that you can only actually ENABLE or DISABLE the thing
- * once after POR. Once enabled, you cannot disable, and vice versa.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/fs.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/miscdevice.h>
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/watchdog.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-
-struct mpc83xx_wdt {
- __be32 res0;
- __be32 swcrr; /* System watchdog control register */
-#define SWCRR_SWTC 0xFFFF0000 /* Software Watchdog Time Count. */
-#define SWCRR_SWEN 0x00000004 /* Watchdog Enable bit. */
-#define SWCRR_SWRI 0x00000002 /* Software Watchdog Reset/Interrupt Select bit.*/
-#define SWCRR_SWPR 0x00000001 /* Software Watchdog Counter Prescale bit. */
- __be32 swcnr; /* System watchdog count register */
- u8 res1[2];
- __be16 swsrr; /* System watchdog service register */
- u8 res2[0xF0];
-};
-
-static struct mpc83xx_wdt __iomem *wd_base;
-
-static u16 timeout = 0xffff;
-module_param(timeout, ushort, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in ticks. (0<timeout<65536, default=65535");
-
-static int reset = 1;
-module_param(reset, bool, 0);
-MODULE_PARM_DESC(reset, "Watchdog Interrupt/Reset Mode. 0 = interrupt, 1 = reset");
-
-/*
- * We always prescale, but if someone really doesn't want to they can set this
- * to 0
- */
-static int prescale = 1;
-static unsigned int timeout_sec;
-
-static unsigned long wdt_is_open;
-static DEFINE_SPINLOCK(wdt_spinlock);
-
-static void mpc83xx_wdt_keepalive(void)
-{
- /* Ping the WDT */
- spin_lock(&wdt_spinlock);
- out_be16(&wd_base->swsrr, 0x556c);
- out_be16(&wd_base->swsrr, 0xaa39);
- spin_unlock(&wdt_spinlock);
-}
-
-static ssize_t mpc83xx_wdt_write(struct file *file, const char __user *buf,
- size_t count, loff_t *ppos)
-{
- if (count)
- mpc83xx_wdt_keepalive();
- return count;
-}
-
-static int mpc83xx_wdt_open(struct inode *inode, struct file *file)
-{
- u32 tmp = SWCRR_SWEN;
- if (test_and_set_bit(0, &wdt_is_open))
- return -EBUSY;
-
- /* Once we start the watchdog we can't stop it */
- __module_get(THIS_MODULE);
-
- /* Good, fire up the show */
- if (prescale)
- tmp |= SWCRR_SWPR;
- if (reset)
- tmp |= SWCRR_SWRI;
-
- tmp |= timeout << 16;
-
- out_be32(&wd_base->swcrr, tmp);
-
- return nonseekable_open(inode, file);
-}
-
-static int mpc83xx_wdt_release(struct inode *inode, struct file *file)
-{
- printk(KERN_CRIT "Unexpected close, not stopping watchdog!\n");
- mpc83xx_wdt_keepalive();
- clear_bit(0, &wdt_is_open);
- return 0;
-}
-
-static int mpc83xx_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- void __user *argp = (void __user *)arg;
- int __user *p = argp;
- static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING,
- .firmware_version = 1,
- .identity = "MPC83xx",
- };
-
- switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- mpc83xx_wdt_keepalive();
- return 0;
- case WDIOC_GETTIMEOUT:
- return put_user(timeout_sec, p);
- default:
- return -ENOTTY;
- }
-}
-
-static const struct file_operations mpc83xx_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = mpc83xx_wdt_write,
- .ioctl = mpc83xx_wdt_ioctl,
- .open = mpc83xx_wdt_open,
- .release = mpc83xx_wdt_release,
-};
-
-static struct miscdevice mpc83xx_wdt_miscdev = {
- .minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &mpc83xx_wdt_fops,
-};
-
-static int __devinit mpc83xx_wdt_probe(struct platform_device *dev)
-{
- struct resource *r;
- int ret;
- unsigned int *freq = dev->dev.platform_data;
-
- /* get a pointer to the register memory */
- r = platform_get_resource(dev, IORESOURCE_MEM, 0);
-
- if (!r) {
- ret = -ENODEV;
- goto err_out;
- }
-
- wd_base = ioremap(r->start, sizeof (struct mpc83xx_wdt));
-
- if (wd_base == NULL) {
- ret = -ENOMEM;
- goto err_out;
- }
-
- ret = misc_register(&mpc83xx_wdt_miscdev);
- if (ret) {
- printk(KERN_ERR "cannot register miscdev on minor=%d "
- "(err=%d)\n",
- WATCHDOG_MINOR, ret);
- goto err_unmap;
- }
-
- /* Calculate the timeout in seconds */
- if (prescale)
- timeout_sec = (timeout * 0x10000) / (*freq);
- else
- timeout_sec = timeout / (*freq);
-
- printk(KERN_INFO "WDT driver for MPC83xx initialized. "
- "mode:%s timeout=%d (%d seconds)\n",
- reset ? "reset":"interrupt", timeout, timeout_sec);
- return 0;
-
-err_unmap:
- iounmap(wd_base);
-err_out:
- return ret;
-}
-
-static int __devexit mpc83xx_wdt_remove(struct platform_device *dev)
-{
- misc_deregister(&mpc83xx_wdt_miscdev);
- iounmap(wd_base);
-
- return 0;
-}
-
-static struct platform_driver mpc83xx_wdt_driver = {
- .probe = mpc83xx_wdt_probe,
- .remove = __devexit_p(mpc83xx_wdt_remove),
- .driver = {
- .name = "mpc83xx_wdt",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init mpc83xx_wdt_init(void)
-{
- return platform_driver_register(&mpc83xx_wdt_driver);
-}
-
-static void __exit mpc83xx_wdt_exit(void)
-{
- platform_driver_unregister(&mpc83xx_wdt_driver);
-}
-
-module_init(mpc83xx_wdt_init);
-module_exit(mpc83xx_wdt_exit);
-
-MODULE_AUTHOR("Dave Updegraff, Kumar Gala");
-MODULE_DESCRIPTION("Driver for watchdog timer in MPC83xx uProcessor");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
-MODULE_ALIAS("platform:mpc83xx_wdt");
#include <linux/module.h>
#include <linux/watchdog.h>
#include <asm/8xx_immap.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#include <syslib/m8xx_wdt.h>
static unsigned long wdt_opened;
static int wdt_status;
+static spinlock_t wdt_lock;
static void mpc8xx_wdt_handler_disable(void)
{
volatile uint __iomem *piscr;
- piscr = (uint *)&((immap_t*)IMAP_ADDR)->im_sit.sit_piscr;
+ piscr = (uint *)&((immap_t *)IMAP_ADDR)->im_sit.sit_piscr;
if (!m8xx_has_internal_rtc)
m8xx_wdt_stop_timer();
else
out_be32(piscr, in_be32(piscr) & ~(PISCR_PIE | PISCR_PTE));
-
printk(KERN_NOTICE "mpc8xx_wdt: keep-alive handler deactivated\n");
}
static void mpc8xx_wdt_handler_enable(void)
{
volatile uint __iomem *piscr;
- piscr = (uint *)&((immap_t*)IMAP_ADDR)->im_sit.sit_piscr;
+ piscr = (uint *)&((immap_t *)IMAP_ADDR)->im_sit.sit_piscr;
if (!m8xx_has_internal_rtc)
m8xx_wdt_install_timer();
else
out_be32(piscr, in_be32(piscr) | PISCR_PIE | PISCR_PTE);
-
printk(KERN_NOTICE "mpc8xx_wdt: keep-alive handler activated\n");
}
{
if (test_and_set_bit(0, &wdt_opened))
return -EBUSY;
-
m8xx_wdt_reset();
mpc8xx_wdt_handler_disable();
-
return nonseekable_open(inode, file);
}
static int mpc8xx_wdt_release(struct inode *inode, struct file *file)
{
m8xx_wdt_reset();
-
#if !defined(CONFIG_WATCHDOG_NOWAYOUT)
mpc8xx_wdt_handler_enable();
#endif
-
clear_bit(0, &wdt_opened);
-
return 0;
}
-static ssize_t mpc8xx_wdt_write(struct file *file, const char *data, size_t len,
- loff_t * ppos)
+static ssize_t mpc8xx_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
- if (len)
+ if (len) {
+ spin_lock(&wdt_lock);
m8xx_wdt_reset();
-
+ spin_unlock(&wdt_lock);
+ }
return len;
}
-static int mpc8xx_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long mpc8xx_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int timeout;
static struct watchdog_info info = {
return -EOPNOTSUPP;
case WDIOC_KEEPALIVE:
+ spin_lock(&wdt_lock);
m8xx_wdt_reset();
wdt_status |= WDIOF_KEEPALIVEPING;
+ spin_unlock(&wdt_lock);
break;
case WDIOC_SETTIMEOUT:
return -EOPNOTSUPP;
case WDIOC_GETTIMEOUT:
+ spin_lock(&wdt_lock);
timeout = m8xx_wdt_get_timeout();
+ spin_unlock(&wdt_lock);
if (put_user(timeout, (int *)arg))
return -EFAULT;
break;
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = mpc8xx_wdt_write,
- .ioctl = mpc8xx_wdt_ioctl,
+ .unlocked_ioctl = mpc8xx_wdt_ioctl,
.open = mpc8xx_wdt_open,
.release = mpc8xx_wdt_release,
};
static int __init mpc8xx_wdt_init(void)
{
+ spin_lock_init(&wdt_lock);
return misc_register(&mpc8xx_wdt_miscdev);
}
--- /dev/null
+/*
+ * mpc8xxx_wdt.c - MPC8xx/MPC83xx/MPC86xx watchdog userspace interface
+ *
+ * Authors: Dave Updegraff <dave@cray.org>
+ * Kumar Gala <galak@kernel.crashing.org>
+ * Attribution: from 83xx_wst: Florian Schirmer <jolt@tuxbox.org>
+ * ..and from sc520_wdt
+ * Copyright (c) 2008 MontaVista Software, Inc.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * Note: it appears that you can only actually ENABLE or DISABLE the thing
+ * once after POR. Once enabled, you cannot disable, and vice versa.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/timer.h>
+#include <linux/miscdevice.h>
+#include <linux/of_platform.h>
+#include <linux/module.h>
+#include <linux/watchdog.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <sysdev/fsl_soc.h>
+
+struct mpc8xxx_wdt {
+ __be32 res0;
+ __be32 swcrr; /* System watchdog control register */
+#define SWCRR_SWTC 0xFFFF0000 /* Software Watchdog Time Count. */
+#define SWCRR_SWEN 0x00000004 /* Watchdog Enable bit. */
+#define SWCRR_SWRI 0x00000002 /* Software Watchdog Reset/Interrupt Select bit.*/
+#define SWCRR_SWPR 0x00000001 /* Software Watchdog Counter Prescale bit. */
+ __be32 swcnr; /* System watchdog count register */
+ u8 res1[2];
+ __be16 swsrr; /* System watchdog service register */
+ u8 res2[0xF0];
+};
+
+struct mpc8xxx_wdt_type {
+ int prescaler;
+ bool hw_enabled;
+};
+
+static struct mpc8xxx_wdt __iomem *wd_base;
+
+static u16 timeout = 0xffff;
+module_param(timeout, ushort, 0);
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in ticks. (0<timeout<65536, default=65535");
+
+static int reset = 1;
+module_param(reset, bool, 0);
+MODULE_PARM_DESC(reset,
+ "Watchdog Interrupt/Reset Mode. 0 = interrupt, 1 = reset");
+
+static int nowayout = WATCHDOG_NOWAYOUT;
+module_param(nowayout, int, 0);
+MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started "
+ "(default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+
+/*
+ * We always prescale, but if someone really doesn't want to they can set this
+ * to 0
+ */
+static int prescale = 1;
+static unsigned int timeout_sec;
+
+static unsigned long wdt_is_open;
+static DEFINE_SPINLOCK(wdt_spinlock);
+
+static void mpc8xxx_wdt_keepalive(void)
+{
+ /* Ping the WDT */
+ spin_lock(&wdt_spinlock);
+ out_be16(&wd_base->swsrr, 0x556c);
+ out_be16(&wd_base->swsrr, 0xaa39);
+ spin_unlock(&wdt_spinlock);
+}
+
+static void mpc8xxx_wdt_timer_ping(unsigned long arg);
+static DEFINE_TIMER(wdt_timer, mpc8xxx_wdt_timer_ping, 0, 0);
+
+static void mpc8xxx_wdt_timer_ping(unsigned long arg)
+{
+ mpc8xxx_wdt_keepalive();
+ /* We're pinging it twice faster than needed, just to be sure. */
+ mod_timer(&wdt_timer, jiffies + HZ * timeout_sec / 2);
+}
+
+static void mpc8xxx_wdt_pr_warn(const char *msg)
+{
+ pr_crit("mpc8xxx_wdt: %s, expect the %s soon!\n", msg,
+ reset ? "reset" : "machine check exception");
+}
+
+static ssize_t mpc8xxx_wdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
+{
+ if (count)
+ mpc8xxx_wdt_keepalive();
+ return count;
+}
+
+static int mpc8xxx_wdt_open(struct inode *inode, struct file *file)
+{
+ u32 tmp = SWCRR_SWEN;
+ if (test_and_set_bit(0, &wdt_is_open))
+ return -EBUSY;
+
+ /* Once we start the watchdog we can't stop it */
+ if (nowayout)
+ __module_get(THIS_MODULE);
+
+ /* Good, fire up the show */
+ if (prescale)
+ tmp |= SWCRR_SWPR;
+ if (reset)
+ tmp |= SWCRR_SWRI;
+
+ tmp |= timeout << 16;
+
+ out_be32(&wd_base->swcrr, tmp);
+
+ del_timer_sync(&wdt_timer);
+
+ return nonseekable_open(inode, file);
+}
+
+static int mpc8xxx_wdt_release(struct inode *inode, struct file *file)
+{
+ if (!nowayout)
+ mpc8xxx_wdt_timer_ping(0);
+ else
+ mpc8xxx_wdt_pr_warn("watchdog closed");
+ clear_bit(0, &wdt_is_open);
+ return 0;
+}
+
+static long mpc8xxx_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
+{
+ void __user *argp = (void __user *)arg;
+ int __user *p = argp;
+ static struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING,
+ .firmware_version = 1,
+ .identity = "MPC8xxx",
+ };
+
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ mpc8xxx_wdt_keepalive();
+ return 0;
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout_sec, p);
+ default:
+ return -ENOTTY;
+ }
+}
+
+static const struct file_operations mpc8xxx_wdt_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = mpc8xxx_wdt_write,
+ .unlocked_ioctl = mpc8xxx_wdt_ioctl,
+ .open = mpc8xxx_wdt_open,
+ .release = mpc8xxx_wdt_release,
+};
+
+static struct miscdevice mpc8xxx_wdt_miscdev = {
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &mpc8xxx_wdt_fops,
+};
+
+static int __devinit mpc8xxx_wdt_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ int ret;
+ struct device_node *np = ofdev->node;
+ struct mpc8xxx_wdt_type *wdt_type = match->data;
+ u32 freq = fsl_get_sys_freq();
+ bool enabled;
+
+ if (!freq || freq == -1)
+ return -EINVAL;
+
+ wd_base = of_iomap(np, 0);
+ if (!wd_base)
+ return -ENOMEM;
+
+ enabled = in_be32(&wd_base->swcrr) & SWCRR_SWEN;
+ if (!enabled && wdt_type->hw_enabled) {
+ pr_info("mpc8xxx_wdt: could not be enabled in software\n");
+ ret = -ENOSYS;
+ goto err_unmap;
+ }
+
+ /* Calculate the timeout in seconds */
+ if (prescale)
+ timeout_sec = (timeout * wdt_type->prescaler) / freq;
+ else
+ timeout_sec = timeout / freq;
+
+ pr_info("WDT driver for MPC8xxx initialized. mode:%s timeout=%d "
+ "(%d seconds)\n", reset ? "reset" : "interrupt", timeout,
+ timeout_sec);
+
+ /*
+ * If the watchdog was previously enabled or we're running on
+ * MPC8xxx, we should ping the wdt from the kernel until the
+ * userspace handles it.
+ */
+ if (enabled)
+ mpc8xxx_wdt_timer_ping(0);
+ return 0;
+err_unmap:
+ iounmap(wd_base);
+ wd_base = NULL;
+ return ret;
+}
+
+static int __devexit mpc8xxx_wdt_remove(struct of_device *ofdev)
+{
+ mpc8xxx_wdt_pr_warn("watchdog removed");
+ del_timer_sync(&wdt_timer);
+ misc_deregister(&mpc8xxx_wdt_miscdev);
+ iounmap(wd_base);
+
+ return 0;
+}
+
+static const struct of_device_id mpc8xxx_wdt_match[] = {
+ {
+ .compatible = "mpc83xx_wdt",
+ .data = &(struct mpc8xxx_wdt_type) {
+ .prescaler = 0x10000,
+ },
+ },
+ {
+ .compatible = "fsl,mpc8610-wdt",
+ .data = &(struct mpc8xxx_wdt_type) {
+ .prescaler = 0x10000,
+ .hw_enabled = true,
+ },
+ },
+ {
+ .compatible = "fsl,mpc823-wdt",
+ .data = &(struct mpc8xxx_wdt_type) {
+ .prescaler = 0x800,
+ },
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mpc8xxx_wdt_match);
+
+static struct of_platform_driver mpc8xxx_wdt_driver = {
+ .match_table = mpc8xxx_wdt_match,
+ .probe = mpc8xxx_wdt_probe,
+ .remove = __devexit_p(mpc8xxx_wdt_remove),
+ .driver = {
+ .name = "mpc8xxx_wdt",
+ .owner = THIS_MODULE,
+ },
+};
+
+/*
+ * We do wdt initialization in two steps: arch_initcall probes the wdt
+ * very early to start pinging the watchdog (misc devices are not yet
+ * available), and later module_init() just registers the misc device.
+ */
+static int __init mpc8xxx_wdt_init_late(void)
+{
+ int ret;
+
+ if (!wd_base)
+ return -ENODEV;
+
+ ret = misc_register(&mpc8xxx_wdt_miscdev);
+ if (ret) {
+ pr_err("cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
+ return ret;
+ }
+ return 0;
+}
+module_init(mpc8xxx_wdt_init_late);
+
+static int __init mpc8xxx_wdt_init(void)
+{
+ return of_register_platform_driver(&mpc8xxx_wdt_driver);
+}
+arch_initcall(mpc8xxx_wdt_init);
+
+static void __exit mpc8xxx_wdt_exit(void)
+{
+ of_unregister_platform_driver(&mpc8xxx_wdt_driver);
+}
+module_exit(mpc8xxx_wdt_exit);
+
+MODULE_AUTHOR("Dave Updegraff, Kumar Gala");
+MODULE_DESCRIPTION("Driver for watchdog timer in MPC8xx/MPC83xx/MPC86xx "
+ "uProcessors");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
+#include <linux/uaccess.h>
#include <asm/hardware/arm_twd.h>
-#include <asm/uaccess.h>
struct mpcore_wdt {
unsigned long timer_alive;
};
static struct platform_device *mpcore_wdt_dev;
-
extern unsigned int mpcore_timer_rate;
#define TIMER_MARGIN 60
static int mpcore_margin = TIMER_MARGIN;
module_param(mpcore_margin, int, 0);
-MODULE_PARM_DESC(mpcore_margin, "MPcore timer margin in seconds. (0<mpcore_margin<65536, default=" __MODULE_STRING(TIMER_MARGIN) ")");
+MODULE_PARM_DESC(mpcore_margin,
+ "MPcore timer margin in seconds. (0 < mpcore_margin < 65536, default="
+ __MODULE_STRING(TIMER_MARGIN) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#define ONLY_TESTING 0
static int mpcore_noboot = ONLY_TESTING;
/* Check it really was our interrupt */
if (readl(wdt->base + TWD_WDOG_INTSTAT)) {
- dev_printk(KERN_CRIT, wdt->dev, "Triggered - Reboot ignored.\n");
-
+ dev_printk(KERN_CRIT, wdt->dev,
+ "Triggered - Reboot ignored.\n");
/* Clear the interrupt on the watchdog */
writel(1, wdt->base + TWD_WDOG_INTSTAT);
-
return IRQ_HANDLED;
}
-
return IRQ_NONE;
}
count = (mpcore_timer_rate / 256) * mpcore_margin;
/* Reload the counter */
+ spin_lock(&wdt_lock);
writel(count + wdt->perturb, wdt->base + TWD_WDOG_LOAD);
-
wdt->perturb = wdt->perturb ? 0 : 1;
+ spin_unlock(&wdt_lock);
}
static void mpcore_wdt_stop(struct mpcore_wdt *wdt)
{
+ spin_lock(&wdt_lock);
writel(0x12345678, wdt->base + TWD_WDOG_DISABLE);
writel(0x87654321, wdt->base + TWD_WDOG_DISABLE);
writel(0x0, wdt->base + TWD_WDOG_CONTROL);
+ spin_unlock(&wdt_lock);
}
static void mpcore_wdt_start(struct mpcore_wdt *wdt)
{
dev_printk(KERN_INFO, wdt->dev, "enabling watchdog.\n");
+ spin_lock(&wdt_lock);
/* This loads the count register but does NOT start the count yet */
mpcore_wdt_keepalive(wdt);
/* Enable watchdog - prescale=256, watchdog mode=1, enable=1 */
writel(0x0000FF09, wdt->base + TWD_WDOG_CONTROL);
}
+ spin_unlock(&wdt_lock);
}
static int mpcore_wdt_set_heartbeat(int t)
* Shut off the timer.
* Lock it in if it's a module and we set nowayout
*/
- if (wdt->expect_close == 42) {
+ if (wdt->expect_close == 42)
mpcore_wdt_stop(wdt);
- } else {
- dev_printk(KERN_CRIT, wdt->dev, "unexpected close, not stopping watchdog!\n");
+ else {
+ dev_printk(KERN_CRIT, wdt->dev,
+ "unexpected close, not stopping watchdog!\n");
mpcore_wdt_keepalive(wdt);
}
clear_bit(0, &wdt->timer_alive);
return 0;
}
-static ssize_t mpcore_wdt_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t mpcore_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
struct mpcore_wdt *wdt = file->private_data;
.identity = "MPcore Watchdog",
};
-static int mpcore_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long mpcore_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
struct mpcore_wdt *wdt = file->private_data;
int ret;
ret = 0;
break;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ uarg.i = 0;
+ ret = 0;
+ break;
+
case WDIOC_SETOPTIONS:
ret = -EINVAL;
if (uarg.i & WDIOS_DISABLECARD) {
}
break;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- uarg.i = 0;
- ret = 0;
- break;
-
case WDIOC_KEEPALIVE:
mpcore_wdt_keepalive(wdt);
ret = 0;
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = mpcore_wdt_write,
- .ioctl = mpcore_wdt_ioctl,
+ .unlocked_ioctl = mpcore_wdt_ioctl,
.open = mpcore_wdt_open,
.release = mpcore_wdt_release,
};
mpcore_wdt_miscdev.parent = &dev->dev;
ret = misc_register(&mpcore_wdt_miscdev);
if (ret) {
- dev_printk(KERN_ERR, _dev, "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ dev_printk(KERN_ERR, _dev,
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto err_misc;
}
- ret = request_irq(wdt->irq, mpcore_wdt_fire, IRQF_DISABLED, "mpcore_wdt", wdt);
+ ret = request_irq(wdt->irq, mpcore_wdt_fire, IRQF_DISABLED,
+ "mpcore_wdt", wdt);
if (ret) {
- dev_printk(KERN_ERR, _dev, "cannot register IRQ%d for watchdog\n", wdt->irq);
+ dev_printk(KERN_ERR, _dev,
+ "cannot register IRQ%d for watchdog\n", wdt->irq);
goto err_irq;
}
return 0;
- err_irq:
+err_irq:
misc_deregister(&mpcore_wdt_miscdev);
- err_misc:
+err_misc:
iounmap(wdt->base);
- err_free:
+err_free:
kfree(wdt);
- err_out:
+err_out:
return ret;
}
*/
if (mpcore_wdt_set_heartbeat(mpcore_margin)) {
mpcore_wdt_set_heartbeat(TIMER_MARGIN);
- printk(KERN_INFO "mpcore_margin value must be 0<mpcore_margin<65536, using %d\n",
+ printk(KERN_INFO "mpcore_margin value must be 0 < mpcore_margin < 65536, using %d\n",
TIMER_MARGIN);
}
/*
* Driver for the MTX-1 Watchdog.
*
- * (C) Copyright 2005 4G Systems <info@4g-systems.biz>, All Rights Reserved.
+ * (C) Copyright 2005 4G Systems <info@4g-systems.biz>,
+ * All Rights Reserved.
* http://www.4g-systems.biz
*
* (C) Copyright 2007 OpenWrt.org, Florian Fainelli <florian@openwrt.org>
#include <linux/jiffies.h>
#include <linux/watchdog.h>
#include <linux/platform_device.h>
-
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <linux/gpio.h>
#include <asm/mach-au1x00/au1000.h>
-#include <asm/gpio.h>
#define MTX1_WDT_INTERVAL (5 * HZ)
static struct {
struct completion stop;
+ spinlock_t lock;
int running;
struct timer_list timer;
int queue;
{
u32 tmp;
+ spin_lock(&mtx1_wdt_device.lock);
if (mtx1_wdt_device.running)
ticks--;
/*
tmp = au_readl(GPIO2_DIR);
tmp = (tmp & ~(1 << mtx1_wdt_device.gpio)) |
((~tmp) & (1 << mtx1_wdt_device.gpio));
- au_writel (tmp, GPIO2_DIR);
+ au_writel(tmp, GPIO2_DIR);
if (mtx1_wdt_device.queue && ticks)
mod_timer(&mtx1_wdt_device.timer, jiffies + MTX1_WDT_INTERVAL);
- else {
+ else
complete(&mtx1_wdt_device.stop);
- }
+ spin_unlock(&mtx1_wdt_device.lock);
}
static void mtx1_wdt_reset(void)
static void mtx1_wdt_start(void)
{
+ spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
if (!mtx1_wdt_device.queue) {
mtx1_wdt_device.queue = 1;
gpio_set_value(mtx1_wdt_device.gpio, 1);
mod_timer(&mtx1_wdt_device.timer, jiffies + MTX1_WDT_INTERVAL);
}
mtx1_wdt_device.running++;
+ spin_unlock_irqrestore(&mtx1_wdt_device.lock, flags);
}
static int mtx1_wdt_stop(void)
{
+ spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
if (mtx1_wdt_device.queue) {
mtx1_wdt_device.queue = 0;
gpio_set_value(mtx1_wdt_device.gpio, 0);
}
-
ticks = mtx1_wdt_device.default_ticks;
-
+ spin_unlock_irqrestore(&mtx1_wdt_device.lock, flags);
return 0;
}
{
if (test_and_set_bit(0, &mtx1_wdt_device.inuse))
return -EBUSY;
-
return nonseekable_open(inode, file);
}
return 0;
}
-static int mtx1_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+static long mtx1_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
+ int __user *p = (int __user *)argp;
unsigned int value;
- static struct watchdog_info ident =
- {
+ static const struct watchdog_info ident = {
.options = WDIOF_CARDRESET,
.identity = "MTX-1 WDT",
};
- switch(cmd) {
- case WDIOC_KEEPALIVE:
- mtx1_wdt_reset();
- break;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- if ( copy_to_user(argp, &value, sizeof(int)) )
- return -EFAULT;
- break;
- case WDIOC_GETSUPPORT:
- if ( copy_to_user(argp, &ident, sizeof(ident)) )
- return -EFAULT;
- break;
- case WDIOC_SETOPTIONS:
- if ( copy_from_user(&value, argp, sizeof(int)) )
- return -EFAULT;
- switch(value) {
- case WDIOS_ENABLECARD:
- mtx1_wdt_start();
- break;
- case WDIOS_DISABLECARD:
- return mtx1_wdt_stop();
- default:
- return -EINVAL;
- }
- break;
- default:
- return -ENOTTY;
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ put_user(0, p);
+ break;
+ case WDIOC_SETOPTIONS:
+ if (get_user(value, p))
+ return -EFAULT;
+ if (value & WDIOS_ENABLECARD)
+ mtx1_wdt_start();
+ else if (value & WDIOS_DISABLECARD)
+ mtx1_wdt_stop();
+ else
+ return -EINVAL;
+ return 0;
+ case WDIOC_KEEPALIVE:
+ mtx1_wdt_reset();
+ break;
+ default:
+ return -ENOTTY;
}
return 0;
}
-static ssize_t mtx1_wdt_write(struct file *file, const char *buf, size_t count, loff_t *ppos)
+static ssize_t mtx1_wdt_write(struct file *file, const char *buf,
+ size_t count, loff_t *ppos)
{
if (!count)
return -EIO;
-
mtx1_wdt_reset();
return count;
}
static const struct file_operations mtx1_wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
- .ioctl = mtx1_wdt_ioctl,
+ .unlocked_ioctl = mtx1_wdt_ioctl,
.open = mtx1_wdt_open,
.write = mtx1_wdt_write,
- .release = mtx1_wdt_release
+ .release = mtx1_wdt_release,
};
static struct miscdevice mtx1_wdt_misc = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
- .fops = &mtx1_wdt_fops
+ .fops = &mtx1_wdt_fops,
};
mtx1_wdt_device.gpio = pdev->resource[0].start;
- if ((ret = misc_register(&mtx1_wdt_misc)) < 0) {
- printk(KERN_ERR " mtx-1_wdt : failed to register\n");
- return ret;
- }
-
+ spin_lock_init(&mtx1_wdt_device.lock);
init_completion(&mtx1_wdt_device.stop);
mtx1_wdt_device.queue = 0;
-
clear_bit(0, &mtx1_wdt_device.inuse);
-
setup_timer(&mtx1_wdt_device.timer, mtx1_wdt_trigger, 0L);
-
mtx1_wdt_device.default_ticks = ticks;
+ ret = misc_register(&mtx1_wdt_misc);
+ if (ret < 0) {
+ printk(KERN_ERR " mtx-1_wdt : failed to register\n");
+ return ret;
+ }
mtx1_wdt_start();
-
printk(KERN_INFO "MTX-1 Watchdog driver\n");
-
return 0;
}
static int mtx1_wdt_remove(struct platform_device *pdev)
{
+ /* FIXME: do we need to lock this test ? */
if (mtx1_wdt_device.queue) {
mtx1_wdt_device.queue = 0;
wait_for_completion(&mtx1_wdt_device.stop);
* and services the watchdog.
*
* Derived from mpc8xx_wdt.c, with the following copyright.
- *
+ *
* 2002 (c) Florian Schirmer <jolt@tuxbox.org> This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
#include <linux/module.h>
#include <linux/watchdog.h>
#include <linux/platform_device.h>
-
#include <linux/mv643xx.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#define MV64x60_WDT_WDC_OFFSET 0
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static int mv64x60_wdt_toggle_wdc(int enabled_predicate, int field_shift)
{
}
static ssize_t mv64x60_wdt_write(struct file *file, const char __user *data,
- size_t len, loff_t * ppos)
+ size_t len, loff_t *ppos)
{
if (len) {
if (!nowayout) {
for (i = 0; i != len; i++) {
char c;
- if(get_user(c, data + i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
return len;
}
-static int mv64x60_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long mv64x60_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int timeout;
int options;
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = mv64x60_wdt_write,
- .ioctl = mv64x60_wdt_ioctl,
+ .unlocked_ioctl = mv64x60_wdt_ioctl,
.open = mv64x60_wdt_open,
.release = mv64x60_wdt_release,
};
#include <linux/moduleparam.h>
#include <linux/clk.h>
#include <linux/bitops.h>
-
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/hardware.h>
-
-#include <asm/arch/prcm.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <mach/hardware.h>
+#include <mach/prcm.h>
#include "omap_wdt.h"
MODULE_PARM_DESC(timer_margin, "initial watchdog timeout (in seconds)");
static int omap_wdt_users;
-static struct clk *armwdt_ck = NULL;
-static struct clk *mpu_wdt_ick = NULL;
-static struct clk *mpu_wdt_fck = NULL;
+static struct clk *armwdt_ck;
+static struct clk *mpu_wdt_ick;
+static struct clk *mpu_wdt_fck;
static unsigned int wdt_trgr_pattern = 0x1234;
+static spinlock_t wdt_lock;
static void omap_wdt_ping(void)
{
return 0;
}
-static ssize_t
-omap_wdt_write(struct file *file, const char __user *data,
+static ssize_t omap_wdt_write(struct file *file, const char __user *data,
size_t len, loff_t *ppos)
{
/* Refresh LOAD_TIME. */
- if (len)
+ if (len) {
+ spin_lock(&wdt_lock);
omap_wdt_ping();
+ spin_unlock(&wdt_lock);
+ }
return len;
}
-static int
-omap_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long omap_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_margin;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.identity = "OMAP Watchdog",
.options = WDIOF_SETTIMEOUT,
.firmware_version = 0,
};
switch (cmd) {
- default:
- return -ENOTTY;
case WDIOC_GETSUPPORT:
return copy_to_user((struct watchdog_info __user *)arg, &ident,
sizeof(ident));
return put_user(omap_prcm_get_reset_sources(),
(int __user *)arg);
case WDIOC_KEEPALIVE:
+ spin_lock(&wdt_lock);
omap_wdt_ping();
+ spin_unlock(&wdt_lock);
return 0;
case WDIOC_SETTIMEOUT:
if (get_user(new_margin, (int __user *)arg))
return -EFAULT;
omap_wdt_adjust_timeout(new_margin);
+ spin_lock(&wdt_lock);
omap_wdt_disable();
omap_wdt_set_timeout();
omap_wdt_enable();
omap_wdt_ping();
+ spin_unlock(&wdt_lock);
/* Fall */
case WDIOC_GETTIMEOUT:
return put_user(timer_margin, (int __user *)arg);
+ default:
+ return -ENOTTY;
}
}
static const struct file_operations omap_wdt_fops = {
.owner = THIS_MODULE,
.write = omap_wdt_write,
- .ioctl = omap_wdt_ioctl,
+ .unlocked_ioctl = omap_wdt_ioctl,
.open = omap_wdt_open,
.release = omap_wdt_release,
};
static struct miscdevice omap_wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
- .fops = &omap_wdt_fops
+ .fops = &omap_wdt_fops,
};
static int __init omap_wdt_probe(struct platform_device *pdev)
static int __init omap_wdt_init(void)
{
+ spin_lock_init(&wdt_lock);
return platform_driver_register(&omap_wdt_driver);
}
#include <linux/spinlock.h>
#include <linux/moduleparam.h>
#include <linux/version.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
/* #define DEBUG 1 */
-#define DEFAULT_TIMEOUT 1 /* 1 minute */
+#define DEFAULT_TIMEOUT 1 /* 1 minute */
#define MAX_TIMEOUT 255
#define VERSION "1.1"
#define PFX MODNAME ": "
#define DPFX MODNAME " - DEBUG: "
-#define WDT_INDEX_IO_PORT (io+0) /* I/O port base (index register) */
+#define WDT_INDEX_IO_PORT (io+0) /* I/O port base (index register) */
#define WDT_DATA_IO_PORT (WDT_INDEX_IO_PORT+1)
#define SWC_LDN 0x04
-#define SIOCFG2 0x22 /* Serial IO register */
-#define WDCTL 0x10 /* Watchdog-Timer-Controll-Register */
-#define WDTO 0x11 /* Watchdog timeout register */
-#define WDCFG 0x12 /* Watchdog config register */
+#define SIOCFG2 0x22 /* Serial IO register */
+#define WDCTL 0x10 /* Watchdog-Timer-Controll-Register */
+#define WDTO 0x11 /* Watchdog timeout register */
+#define WDCFG 0x12 /* Watchdog config register */
-static int io = 0x2E; /* Address used on Portwell Boards */
+static int io = 0x2E; /* Address used on Portwell Boards */
-static int timeout = DEFAULT_TIMEOUT; /* timeout value */
-static unsigned long timer_enabled = 0; /* is the timer enabled? */
+static int timeout = DEFAULT_TIMEOUT; /* timeout value */
+static unsigned long timer_enabled; /* is the timer enabled? */
-static char expect_close; /* is the close expected? */
+static char expect_close; /* is the close expected? */
-static DEFINE_SPINLOCK(io_lock);/* to guard the watchdog from io races */
+static DEFINE_SPINLOCK(io_lock); /* to guard us from io races */
static int nowayout = WATCHDOG_NOWAYOUT;
/* Select pins for Watchdog output */
-static inline void pc87413_select_wdt_out (void)
+static inline void pc87413_select_wdt_out(void)
{
unsigned int cr_data = 0;
outb_p(SIOCFG2, WDT_INDEX_IO_PORT);
- cr_data = inb (WDT_DATA_IO_PORT);
+ cr_data = inb(WDT_DATA_IO_PORT);
cr_data |= 0x80; /* Set Bit7 to 1*/
outb_p(SIOCFG2, WDT_INDEX_IO_PORT);
outb_p(cr_data, WDT_DATA_IO_PORT);
#ifdef DEBUG
- printk(KERN_INFO DPFX "Select multiple pin,pin55,as WDT output:"
- " Bit7 to 1: %d\n", cr_data);
+ printk(KERN_INFO DPFX
+ "Select multiple pin,pin55,as WDT output: Bit7 to 1: %d\n",
+ cr_data);
#endif
}
static inline void pc87413_enable_swc(void)
{
- unsigned int cr_data=0;
+ unsigned int cr_data = 0;
/* Step 2: Enable SWC functions */
- outb_p(0x07, WDT_INDEX_IO_PORT); /* Point SWC_LDN (LDN=4) */
+ outb_p(0x07, WDT_INDEX_IO_PORT); /* Point SWC_LDN (LDN=4) */
outb_p(SWC_LDN, WDT_DATA_IO_PORT);
- outb_p(0x30, WDT_INDEX_IO_PORT); /* Read Index 0x30 First */
+ outb_p(0x30, WDT_INDEX_IO_PORT); /* Read Index 0x30 First */
cr_data = inb(WDT_DATA_IO_PORT);
- cr_data |= 0x01; /* Set Bit0 to 1 */
+ cr_data |= 0x01; /* Set Bit0 to 1 */
outb_p(0x30, WDT_INDEX_IO_PORT);
- outb_p(cr_data, WDT_DATA_IO_PORT); /* Index0x30_bit0P1 */
+ outb_p(cr_data, WDT_DATA_IO_PORT); /* Index0x30_bit0P1 */
#ifdef DEBUG
printk(KERN_INFO DPFX "pc87413 - Enable SWC functions\n");
/* Step 3: Read SWC I/O Base Address */
- outb_p(0x60, WDT_INDEX_IO_PORT); /* Read Index 0x60 */
+ outb_p(0x60, WDT_INDEX_IO_PORT); /* Read Index 0x60 */
addr_h = inb(WDT_DATA_IO_PORT);
- outb_p(0x61, WDT_INDEX_IO_PORT); /* Read Index 0x61 */
+ outb_p(0x61, WDT_INDEX_IO_PORT); /* Read Index 0x61 */
addr_l = inb(WDT_DATA_IO_PORT);
swc_base_addr = (addr_h << 8) + addr_l;
-
#ifdef DEBUG
- printk(KERN_INFO DPFX "Read SWC I/O Base Address: low %d, high %d,"
- " res %d\n", addr_l, addr_h, swc_base_addr);
+ printk(KERN_INFO DPFX
+ "Read SWC I/O Base Address: low %d, high %d, res %d\n",
+ addr_l, addr_h, swc_base_addr);
#endif
-
return swc_base_addr;
}
static inline void pc87413_swc_bank3(unsigned int swc_base_addr)
{
/* Step 4: Select Bank3 of SWC */
-
outb_p(inb(swc_base_addr + 0x0f) | 0x03, swc_base_addr + 0x0f);
-
#ifdef DEBUG
printk(KERN_INFO DPFX "Select Bank3 of SWC\n");
#endif
char pc87413_time)
{
/* Step 5: Programm WDTO, Twd. */
-
outb_p(pc87413_time, swc_base_addr + WDTO);
-
#ifdef DEBUG
printk(KERN_INFO DPFX "Set WDTO to %d minutes\n", pc87413_time);
#endif
static inline void pc87413_enable_wden(unsigned int swc_base_addr)
{
/* Step 6: Enable WDEN */
-
- outb_p(inb (swc_base_addr + WDCTL) | 0x01, swc_base_addr + WDCTL);
-
+ outb_p(inb(swc_base_addr + WDCTL) | 0x01, swc_base_addr + WDCTL);
#ifdef DEBUG
printk(KERN_INFO DPFX "Enable WDEN\n");
#endif
static inline void pc87413_enable_sw_wd_tren(unsigned int swc_base_addr)
{
/* Enable SW_WD_TREN */
-
- outb_p(inb (swc_base_addr + WDCFG) | 0x80, swc_base_addr + WDCFG);
-
+ outb_p(inb(swc_base_addr + WDCFG) | 0x80, swc_base_addr + WDCFG);
#ifdef DEBUG
printk(KERN_INFO DPFX "Enable SW_WD_TREN\n");
#endif
static inline void pc87413_disable_sw_wd_tren(unsigned int swc_base_addr)
{
/* Disable SW_WD_TREN */
-
- outb_p(inb (swc_base_addr + WDCFG) & 0x7f, swc_base_addr + WDCFG);
-
+ outb_p(inb(swc_base_addr + WDCFG) & 0x7f, swc_base_addr + WDCFG);
#ifdef DEBUG
printk(KERN_INFO DPFX "pc87413 - Disable SW_WD_TREN\n");
#endif
static inline void pc87413_enable_sw_wd_trg(unsigned int swc_base_addr)
{
/* Enable SW_WD_TRG */
-
- outb_p(inb (swc_base_addr + WDCTL) | 0x80, swc_base_addr + WDCTL);
-
+ outb_p(inb(swc_base_addr + WDCTL) | 0x80, swc_base_addr + WDCTL);
#ifdef DEBUG
printk(KERN_INFO DPFX "pc87413 - Enable SW_WD_TRG\n");
#endif
static inline void pc87413_disable_sw_wd_trg(unsigned int swc_base_addr)
{
/* Disable SW_WD_TRG */
-
- outb_p(inb (swc_base_addr + WDCTL) & 0x7f, swc_base_addr + WDCTL);
-
+ outb_p(inb(swc_base_addr + WDCTL) & 0x7f, swc_base_addr + WDCTL);
#ifdef DEBUG
printk(KERN_INFO DPFX "Disable SW_WD_TRG\n");
#endif
/* Reload and activate timer */
pc87413_refresh();
- printk(KERN_INFO MODNAME "Watchdog enabled. Timeout set to"
- " %d minute(s).\n", timeout);
+ printk(KERN_INFO MODNAME
+ "Watchdog enabled. Timeout set to %d minute(s).\n", timeout);
return nonseekable_open(inode, file);
}
if (expect_close == 42) {
pc87413_disable();
- printk(KERN_INFO MODNAME "Watchdog disabled,"
- " sleeping again...\n");
+ printk(KERN_INFO MODNAME
+ "Watchdog disabled, sleeping again...\n");
} else {
- printk(KERN_CRIT MODNAME "Unexpected close, not stopping"
- " watchdog!\n");
+ printk(KERN_CRIT MODNAME
+ "Unexpected close, not stopping watchdog!\n");
pc87413_refresh();
}
-
clear_bit(0, &timer_enabled);
expect_close = 0;
-
return 0;
}
/* reset expect flag */
expect_close = 0;
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got the
+ magic character */
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
/**
* pc87413_ioctl:
- * @inode: inode of the device
* @file: file handle to the device
* @cmd: watchdog command
* @arg: argument pointer
* querying capabilities and current status.
*/
-static int pc87413_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long pc87413_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_timeout;
static struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING |
- WDIOF_SETTIMEOUT |
- WDIOF_MAGICCLOSE,
+ WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE,
.firmware_version = 1,
- .identity = "PC87413(HF/F) watchdog"
+ .identity = "PC87413(HF/F) watchdog",
};
uarg.i = (int __user *)arg;
- switch(cmd) {
- default:
- return -ENOTTY;
-
- case WDIOC_GETSUPPORT:
- return copy_to_user(uarg.ident, &ident,
- sizeof(ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- return put_user(pc87413_status(), uarg.i);
-
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, uarg.i);
-
- case WDIOC_KEEPALIVE:
- pc87413_refresh();
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(uarg.ident, &ident,
+ sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ return put_user(pc87413_status(), uarg.i);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, uarg.i);
+ case WDIOC_SETOPTIONS:
+ {
+ int options, retval = -EINVAL;
+ if (get_user(options, uarg.i))
+ return -EFAULT;
+ if (options & WDIOS_DISABLECARD) {
+ pc87413_disable();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ pc87413_enable();
+ retval = 0;
+ }
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ pc87413_refresh();
#ifdef DEBUG
- printk(KERN_INFO DPFX "keepalive\n");
+ printk(KERN_INFO DPFX "keepalive\n");
#endif
- return 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, uarg.i))
- return -EFAULT;
-
- // the API states this is given in secs
- new_timeout /= 60;
-
- if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
- return -EINVAL;
-
- timeout = new_timeout;
- pc87413_refresh();
-
- // fall through and return the new timeout...
-
- case WDIOC_GETTIMEOUT:
-
- new_timeout = timeout * 60;
-
- return put_user(new_timeout, uarg.i);
-
- case WDIOC_SETOPTIONS:
- {
- int options, retval = -EINVAL;
-
- if (get_user(options, uarg.i))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- pc87413_disable();
- retval = 0;
- }
-
- if (options & WDIOS_ENABLECARD) {
- pc87413_enable();
- retval = 0;
- }
-
- return retval;
- }
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, uarg.i))
+ return -EFAULT;
+ /* the API states this is given in secs */
+ new_timeout /= 60;
+ if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
+ return -EINVAL;
+ timeout = new_timeout;
+ pc87413_refresh();
+ /* fall through and return the new timeout... */
+ case WDIOC_GETTIMEOUT:
+ new_timeout = timeout * 60;
+ return put_user(new_timeout, uarg.i);
+ default:
+ return -ENOTTY;
}
}
void *unused)
{
if (code == SYS_DOWN || code == SYS_HALT)
- {
/* Turn the card off */
pc87413_disable();
- }
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = pc87413_write,
- .ioctl = pc87413_ioctl,
+ .unlocked_ioctl = pc87413_ioctl,
.open = pc87413_open,
.release = pc87413_release,
};
-static struct notifier_block pc87413_notifier =
-{
+static struct notifier_block pc87413_notifier = {
.notifier_call = pc87413_notify_sys,
};
-static struct miscdevice pc87413_miscdev=
-{
+static struct miscdevice pc87413_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
- .fops = &pc87413_fops
+ .fops = &pc87413_fops,
};
/* -- Module init functions -------------------------------------*/
{
int ret;
- printk(KERN_INFO PFX "Version " VERSION " at io 0x%X\n", WDT_INDEX_IO_PORT);
+ printk(KERN_INFO PFX "Version " VERSION " at io 0x%X\n",
+ WDT_INDEX_IO_PORT);
/* request_region(io, 2, "pc87413"); */
ret = register_reboot_notifier(&pc87413_notifier);
if (ret != 0) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
}
ret = misc_register(&pc87413_miscdev);
-
if (ret != 0) {
printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
WATCHDOG_MINOR, ret);
unregister_reboot_notifier(&pc87413_notifier);
return ret;
}
-
printk(KERN_INFO PFX "initialized. timeout=%d min \n", timeout);
-
pc87413_enable();
-
return 0;
}
static void __exit pc87413_exit(void)
{
/* Stop the timer before we leave */
- if (!nowayout)
- {
+ if (!nowayout) {
pc87413_disable();
printk(KERN_INFO MODNAME "Watchdog disabled.\n");
}
misc_deregister(&pc87413_miscdev);
unregister_reboot_notifier(&pc87413_notifier);
- /* release_region(io,2); */
+ /* release_region(io, 2); */
- printk(MODNAME " watchdog component driver removed.\n");
+ printk(KERN_INFO MODNAME " watchdog component driver removed.\n");
}
module_init(pc87413_init);
MODULE_PARM_DESC(io, MODNAME " I/O port (default: " __MODULE_STRING(io) ").");
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in minutes (default=" __MODULE_STRING(timeout) ").");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in minutes (default="
+ __MODULE_STRING(timeout) ").");
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
* fairly useless proc entry.
* 990610 removed said useless proc code for the merge <alan>
* 000403 Removed last traces of proc code. <davej>
- * 011214 Added nowayout module option to override CONFIG_WATCHDOG_NOWAYOUT <Matt_Domsch@dell.com>
+ * 011214 Added nowayout module option to override
+ * CONFIG_WATCHDOG_NOWAYOUT <Matt_Domsch@dell.com>
* Added timeout module option to override default
*/
/*
* A bells and whistles driver is available from http://www.pcwd.de/
- * More info available at http://www.berkprod.com/ or http://www.pcwatchdog.com/
+ * More info available at http://www.berkprod.com/ or
+ * http://www.pcwatchdog.com/
*/
#include <linux/module.h> /* For module specific items */
#include <linux/isa.h> /* For isa devices */
#include <linux/ioport.h> /* For io-port access */
#include <linux/spinlock.h> /* For spin_lock/spin_unlock/... */
-
-#include <asm/uaccess.h> /* For copy_to_user/put_user/... */
-#include <asm/io.h> /* For inb/outb/... */
+#include <linux/uaccess.h> /* For copy_to_user/put_user/... */
+#include <linux/io.h> /* For inb/outb/... */
/* Module and version information */
#define WATCHDOG_VERSION "1.20"
#define WD_REVC_WTRP 0x01 /* Watchdog Trip status */
#define WD_REVC_HRBT 0x02 /* Watchdog Heartbeat */
#define WD_REVC_TTRP 0x04 /* Temperature Trip status */
-#define WD_REVC_RL2A 0x08 /* Relay 2 activated by on-board processor */
+#define WD_REVC_RL2A 0x08 /* Relay 2 activated by
+ on-board processor */
#define WD_REVC_RL1A 0x10 /* Relay 1 active */
#define WD_REVC_R2DS 0x40 /* Relay 2 disable */
#define WD_REVC_RLY2 0x80 /* Relay 2 activated? */
/* Port 2 : Control Status #2 */
#define WD_WDIS 0x10 /* Watchdog Disabled */
#define WD_ENTP 0x20 /* Watchdog Enable Temperature Trip */
-#define WD_SSEL 0x40 /* Watchdog Switch Select (1:SW1 <-> 0:SW2) */
+#define WD_SSEL 0x40 /* Watchdog Switch Select
+ (1:SW1 <-> 0:SW2) */
#define WD_WCMD 0x80 /* Watchdog Command Mode */
/* max. time we give an ISA watchdog card to process a command */
#define CMD_ISA_RESET_RELAYS 0x0D
/* Watchdog's Dip Switch heartbeat values */
-static const int heartbeat_tbl [] = {
+static const int heartbeat_tbl[] = {
20, /* OFF-OFF-OFF = 20 Sec */
40, /* OFF-OFF-ON = 40 Sec */
60, /* OFF-ON-OFF = 1 Min */
static atomic_t open_allowed = ATOMIC_INIT(1);
static char expect_close;
static int temp_panic;
-static struct { /* this is private data for each ISA-PC watchdog card */
+
+/* this is private data for each ISA-PC watchdog card */
+static struct {
char fw_ver_str[6]; /* The cards firmware version */
int revision; /* The card's revision */
- int supports_temp; /* Wether or not the card has a temperature device */
- int command_mode; /* Wether or not the card is in command mode */
+ int supports_temp; /* Whether or not the card has
+ a temperature device */
+ int command_mode; /* Whether or not the card is in
+ command mode */
int boot_status; /* The card's boot status */
int io_addr; /* The cards I/O address */
spinlock_t io_lock; /* the lock for io operations */
#define DEBUG 2 /* print fancy stuff too */
static int debug = QUIET;
module_param(debug, int, 0);
-MODULE_PARM_DESC(debug, "Debug level: 0=Quiet, 1=Verbose, 2=Debug (default=0)");
+MODULE_PARM_DESC(debug,
+ "Debug level: 0=Quiet, 1=Verbose, 2=Debug (default=0)");
-#define WATCHDOG_HEARTBEAT 0 /* default heartbeat = delay-time from dip-switches */
+/* default heartbeat = delay-time from dip-switches */
+#define WATCHDOG_HEARTBEAT 0
static int heartbeat = WATCHDOG_HEARTBEAT;
module_param(heartbeat, int, 0);
-MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (2<=heartbeat<=7200 or 0=delay-time from dip-switches, default=" __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
+MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (2 <= heartbeat <= 7200 or 0=delay-time from dip-switches, default=" __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Internal functions
if (port0 == last_port0)
break; /* Data is stable */
- udelay (250);
+ udelay(250);
}
if (debug >= DEBUG)
static int set_command_mode(void)
{
- int i, found=0, count=0;
+ int i, found = 0, count = 0;
/* Set the card into command mode */
spin_lock(&pcwd_private.io_lock);
printk(KERN_DEBUG PFX "command_mode=%d\n",
pcwd_private.command_mode);
- return(found);
+ return found;
}
static void unset_command_mode(void)
ten = send_isa_command(CMD_ISA_VERSION_TENTH);
hund = send_isa_command(CMD_ISA_VERSION_HUNDRETH);
minor = send_isa_command(CMD_ISA_VERSION_MINOR);
- sprintf(pcwd_private.fw_ver_str, "%c.%c%c%c", one, ten, hund, minor);
+ sprintf(pcwd_private.fw_ver_str, "%c.%c%c%c",
+ one, ten, hund, minor);
}
unset_command_mode();
static inline int pcwd_get_option_switches(void)
{
- int option_switches=0;
+ int option_switches = 0;
if (set_command_mode()) {
/* Get switch settings */
}
unset_command_mode();
- return(option_switches);
+ return option_switches;
}
static void pcwd_show_card_info(void)
/* Get some extra info from the hardware (in command/debug/diag mode) */
if (pcwd_private.revision == PCWD_REVISION_A)
- printk(KERN_INFO PFX "ISA-PC Watchdog (REV.A) detected at port 0x%04x\n", pcwd_private.io_addr);
+ printk(KERN_INFO PFX
+ "ISA-PC Watchdog (REV.A) detected at port 0x%04x\n",
+ pcwd_private.io_addr);
else if (pcwd_private.revision == PCWD_REVISION_C) {
pcwd_get_firmware();
printk(KERN_INFO PFX "ISA-PC Watchdog (REV.C) detected at port 0x%04x (Firmware version: %s)\n",
printk(KERN_INFO PFX "Previous reboot was caused by the card\n");
if (pcwd_private.boot_status & WDIOF_OVERHEAT) {
- printk(KERN_EMERG PFX "Card senses a CPU Overheat. Panicking!\n");
- printk(KERN_EMERG PFX "CPU Overheat\n");
+ printk(KERN_EMERG PFX
+ "Card senses a CPU Overheat. Panicking!\n");
+ printk(KERN_EMERG PFX
+ "CPU Overheat\n");
}
if (pcwd_private.boot_status == 0)
- printk(KERN_INFO PFX "No previous trip detected - Cold boot or reset\n");
+ printk(KERN_INFO PFX
+ "No previous trip detected - Cold boot or reset\n");
}
static void pcwd_timer_ping(unsigned long data)
/* If we got a heartbeat pulse within the WDT_INTERVAL
* we agree to ping the WDT */
- if(time_before(jiffies, pcwd_private.next_heartbeat)) {
+ if (time_before(jiffies, pcwd_private.next_heartbeat)) {
/* Ping the watchdog */
spin_lock(&pcwd_private.io_lock);
if (pcwd_private.revision == PCWD_REVISION_A) {
- /* Rev A cards are reset by setting the WD_WDRST bit in register 1 */
+ /* Rev A cards are reset by setting the
+ WD_WDRST bit in register 1 */
wdrst_stat = inb_p(pcwd_private.io_addr);
wdrst_stat &= 0x0F;
wdrst_stat |= WD_WDRST;
spin_unlock(&pcwd_private.io_lock);
} else {
- printk(KERN_WARNING PFX "Heartbeat lost! Will not ping the watchdog\n");
+ printk(KERN_WARNING PFX
+ "Heartbeat lost! Will not ping the watchdog\n");
}
}
static int pcwd_set_heartbeat(int t)
{
- if ((t < 2) || (t > 7200)) /* arbitrary upper limit */
+ if (t < 2 || t > 7200) /* arbitrary upper limit */
return -EINVAL;
heartbeat = t;
{
int control_status;
- *status=0;
+ *status = 0;
spin_lock(&pcwd_private.io_lock);
if (pcwd_private.revision == PCWD_REVISION_A)
/* Rev A cards return status information from
if (control_status & WD_T110) {
*status |= WDIOF_OVERHEAT;
if (temp_panic) {
- printk(KERN_INFO PFX "Temperature overheat trip!\n");
+ printk(KERN_INFO PFX
+ "Temperature overheat trip!\n");
kernel_power_off();
- /* or should we just do a: panic(PFX "Temperature overheat trip!\n"); */
}
}
} else {
if (control_status & WD_REVC_TTRP) {
*status |= WDIOF_OVERHEAT;
if (temp_panic) {
- printk(KERN_INFO PFX "Temperature overheat trip!\n");
+ printk(KERN_INFO PFX
+ "Temperature overheat trip!\n");
kernel_power_off();
- /* or should we just do a: panic(PFX "Temperature overheat trip!\n"); */
}
}
}
spin_lock(&pcwd_private.io_lock);
if (debug >= VERBOSE)
- printk(KERN_INFO PFX "clearing watchdog trip status\n");
+ printk(KERN_INFO PFX
+ "clearing watchdog trip status\n");
control_status = inb_p(pcwd_private.io_addr + 1);
if (debug >= DEBUG) {
- printk(KERN_DEBUG PFX "status was: 0x%02x\n", control_status);
+ printk(KERN_DEBUG PFX "status was: 0x%02x\n",
+ control_status);
printk(KERN_DEBUG PFX "sending: 0x%02x\n",
(control_status & WD_REVC_R2DS));
}
/* clear reset status & Keep Relay 2 disable state as it is */
- outb_p((control_status & WD_REVC_R2DS), pcwd_private.io_addr + 1);
+ outb_p((control_status & WD_REVC_R2DS),
+ pcwd_private.io_addr + 1);
spin_unlock(&pcwd_private.io_lock);
}
* /dev/watchdog handling
*/
-static int pcwd_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long pcwd_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int rv;
int status;
.identity = "PCWD",
};
- switch(cmd) {
- default:
- return -ENOTTY;
-
+ switch (cmd) {
case WDIOC_GETSUPPORT:
- if(copy_to_user(argp, &ident, sizeof(ident)))
+ if (copy_to_user(argp, &ident, sizeof(ident)))
return -EFAULT;
return 0;
return put_user(temperature, argp);
case WDIOC_SETOPTIONS:
- if (pcwd_private.revision == PCWD_REVISION_C)
- {
- if(copy_from_user(&rv, argp, sizeof(int)))
+ if (pcwd_private.revision == PCWD_REVISION_C) {
+ if (get_user(rv, argp))
return -EFAULT;
- if (rv & WDIOS_DISABLECARD)
- {
- return pcwd_stop();
+ if (rv & WDIOS_DISABLECARD) {
+ status = pcwd_stop();
+ if (status < 0)
+ return status;
}
-
- if (rv & WDIOS_ENABLECARD)
- {
- return pcwd_start();
+ if (rv & WDIOS_ENABLECARD) {
+ status = pcwd_start();
+ if (status < 0)
+ return status;
}
-
if (rv & WDIOS_TEMPPANIC)
- {
temp_panic = 1;
- }
}
return -EINVAL;
case WDIOC_GETTIMEOUT:
return put_user(heartbeat, argp);
+
+ default:
+ return -ENOTTY;
}
return 0;
static int pcwd_open(struct inode *inode, struct file *file)
{
- if (!atomic_dec_and_test(&open_allowed) ) {
- if (debug >= VERBOSE)
- printk(KERN_ERR PFX "Attempt to open already opened device.\n");
- atomic_inc( &open_allowed );
+ if (test_and_set_bit(0, &open_allowed))
return -EBUSY;
- }
-
if (nowayout)
__module_get(THIS_MODULE);
-
/* Activate */
pcwd_start();
pcwd_keepalive();
static int pcwd_close(struct inode *inode, struct file *file)
{
- if (expect_close == 42) {
+ if (expect_close == 42)
pcwd_stop();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
pcwd_keepalive();
}
expect_close = 0;
- atomic_inc( &open_allowed );
+ clear_bit(0, &open_allowed);
return 0;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = pcwd_write,
- .ioctl = pcwd_ioctl,
+ .unlocked_ioctl = pcwd_ioctl,
.open = pcwd_open,
.release = pcwd_close,
};
* presumes a floating bus reads as 0xff. */
if ((inb(pcwd_private.io_addr + 2) == 0xFF) ||
(inb(pcwd_private.io_addr + 3) == 0xFF))
- r=PCWD_REVISION_A;
+ r = PCWD_REVISION_A;
spin_unlock(&pcwd_private.io_lock);
return r;
*/
static int __devinit pcwd_isa_match(struct device *dev, unsigned int id)
{
- int base_addr=pcwd_ioports[id];
+ int base_addr = pcwd_ioports[id];
int port0, last_port0; /* Reg 0, in case it's REV A */
int port1, last_port1; /* Register 1 for REV C cards */
int i;
printk(KERN_DEBUG PFX "pcwd_isa_match id=%d\n",
id);
- if (!request_region (base_addr, 4, "PCWD")) {
+ if (!request_region(base_addr, 4, "PCWD")) {
printk(KERN_INFO PFX "Port 0x%04x unavailable\n", base_addr);
return 0;
}
}
}
}
- release_region (base_addr, 4);
+ release_region(base_addr, 4);
return retval;
}
cards_found++;
if (cards_found == 1)
- printk(KERN_INFO PFX "v%s Ken Hollis (kenji@bitgate.com)\n", WD_VER);
+ printk(KERN_INFO PFX "v%s Ken Hollis (kenji@bitgate.com)\n",
+ WD_VER);
if (cards_found > 1) {
printk(KERN_ERR PFX "This driver only supports 1 device\n");
/* Check card's revision */
pcwd_private.revision = get_revision();
- if (!request_region(pcwd_private.io_addr, (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4, "PCWD")) {
+ if (!request_region(pcwd_private.io_addr,
+ (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4, "PCWD")) {
printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
pcwd_private.io_addr);
- ret=-EIO;
+ ret = -EIO;
goto error_request_region;
}
if (heartbeat == 0)
heartbeat = heartbeat_tbl[(pcwd_get_option_switches() & 0x07)];
- /* Check that the heartbeat value is within it's range ; if not reset to the default */
+ /* Check that the heartbeat value is within it's range;
+ if not reset to the default */
if (pcwd_set_heartbeat(heartbeat)) {
pcwd_set_heartbeat(WATCHDOG_HEARTBEAT);
- printk(KERN_INFO PFX "heartbeat value must be 2<=heartbeat<=7200, using %d\n",
- WATCHDOG_HEARTBEAT);
+ printk(KERN_INFO PFX
+ "heartbeat value must be 2 <= heartbeat <= 7200, using %d\n",
+ WATCHDOG_HEARTBEAT);
}
if (pcwd_private.supports_temp) {
ret = misc_register(&temp_miscdev);
if (ret) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- TEMP_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ TEMP_MINOR, ret);
goto error_misc_register_temp;
}
}
ret = misc_register(&pcwd_miscdev);
if (ret) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto error_misc_register_watchdog;
}
if (pcwd_private.supports_temp)
misc_deregister(&temp_miscdev);
error_misc_register_temp:
- release_region(pcwd_private.io_addr, (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4);
+ release_region(pcwd_private.io_addr,
+ (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4);
error_request_region:
pcwd_private.io_addr = 0x0000;
cards_found--;
misc_deregister(&pcwd_miscdev);
if (pcwd_private.supports_temp)
misc_deregister(&temp_miscdev);
- release_region(pcwd_private.io_addr, (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4);
+ release_region(pcwd_private.io_addr,
+ (pcwd_private.revision == PCWD_REVISION_A) ? 2 : 4);
pcwd_private.io_addr = 0x0000;
cards_found--;
#include <linux/pci.h> /* For pci functions */
#include <linux/ioport.h> /* For io-port access */
#include <linux/spinlock.h> /* For spin_lock/spin_unlock/... */
-
-#include <asm/uaccess.h> /* For copy_to_user/put_user/... */
-#include <asm/io.h> /* For inb/outb/... */
+#include <linux/uaccess.h> /* For copy_to_user/put_user/... */
+#include <linux/io.h> /* For inb/outb/... */
/* Module and version information */
#define WATCHDOG_VERSION "1.03"
#define CMD_GET_CLEAR_RESET_COUNT 0x84
/* Watchdog's Dip Switch heartbeat values */
-static const int heartbeat_tbl [] = {
+static const int heartbeat_tbl[] = {
5, /* OFF-OFF-OFF = 5 Sec */
10, /* OFF-OFF-ON = 10 Sec */
30, /* OFF-ON-OFF = 30 Sec */
int option_switches;
got_fw_rev = send_command(CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor);
- if (got_fw_rev) {
+ if (got_fw_rev)
sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor);
- } else {
+ else
sprintf(fw_ver_str, "<card no answer>");
- }
/* Get switch settings */
option_switches = pcipcwd_get_option_switches();
{
int control_status;
- *status=0;
+ *status = 0;
control_status = inb_p(pcipcwd_private.io_addr + 1);
if (control_status & WD_PCI_WTRP)
*status |= WDIOF_CARDRESET;
outb_p((control_status & WD_PCI_R2DS) | WD_PCI_WTRP, pcipcwd_private.io_addr + 1);
/* clear reset counter */
- msb=0;
- reset_counter=0xff;
+ msb = 0;
+ reset_counter = 0xff;
send_command(CMD_GET_CLEAR_RESET_COUNT, &msb, &reset_counter);
if (debug >= DEBUG) {
/* scan to see whether or not we got the magic character */
for (i = 0; i != len; i++) {
char c;
- if(get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_release = 42;
return len;
}
-static int pcipcwd_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long pcipcwd_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
};
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof (ident)) ? -EFAULT : 0;
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+
+ case WDIOC_GETSTATUS:
+ {
+ int status;
+ pcipcwd_get_status(&status);
+ return put_user(status, p);
+ }
- case WDIOC_GETSTATUS:
- {
- int status;
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(pcipcwd_private.boot_status, p);
- pcipcwd_get_status(&status);
+ case WDIOC_GETTEMP:
+ {
+ int temperature;
- return put_user(status, p);
- }
+ if (pcipcwd_get_temperature(&temperature))
+ return -EFAULT;
- case WDIOC_GETBOOTSTATUS:
- return put_user(pcipcwd_private.boot_status, p);
+ return put_user(temperature, p);
+ }
- case WDIOC_GETTEMP:
- {
- int temperature;
+ case WDIOC_SETOPTIONS:
+ {
+ int new_options, retval = -EINVAL;
- if (pcipcwd_get_temperature(&temperature))
- return -EFAULT;
+ if (get_user(new_options, p))
+ return -EFAULT;
- return put_user(temperature, p);
+ if (new_options & WDIOS_DISABLECARD) {
+ if (pcipcwd_stop())
+ return -EIO;
+ retval = 0;
}
- case WDIOC_KEEPALIVE:
- pcipcwd_keepalive();
- return 0;
-
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if (get_user (new_options, p))
- return -EFAULT;
-
- if (new_options & WDIOS_DISABLECARD) {
- if (pcipcwd_stop())
- return -EIO;
- retval = 0;
- }
+ if (new_options & WDIOS_ENABLECARD) {
+ if (pcipcwd_start())
+ return -EIO;
+ retval = 0;
+ }
- if (new_options & WDIOS_ENABLECARD) {
- if (pcipcwd_start())
- return -EIO;
- retval = 0;
- }
+ if (new_options & WDIOS_TEMPPANIC) {
+ temp_panic = 1;
+ retval = 0;
+ }
- if (new_options & WDIOS_TEMPPANIC) {
- temp_panic = 1;
- retval = 0;
- }
+ return retval;
+ }
- return retval;
- }
+ case WDIOC_KEEPALIVE:
+ pcipcwd_keepalive();
+ return 0;
- case WDIOC_SETTIMEOUT:
- {
- int new_heartbeat;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_heartbeat;
- if (get_user(new_heartbeat, p))
- return -EFAULT;
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
- if (pcipcwd_set_heartbeat(new_heartbeat))
- return -EINVAL;
+ if (pcipcwd_set_heartbeat(new_heartbeat))
+ return -EINVAL;
- pcipcwd_keepalive();
- /* Fall */
- }
+ pcipcwd_keepalive();
+ /* Fall */
+ }
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
- case WDIOC_GETTIMELEFT:
- {
- int time_left;
+ case WDIOC_GETTIMELEFT:
+ {
+ int time_left;
- if (pcipcwd_get_timeleft(&time_left))
- return -EFAULT;
+ if (pcipcwd_get_timeleft(&time_left))
+ return -EFAULT;
- return put_user(time_left, p);
- }
+ return put_user(time_left, p);
+ }
- default:
- return -ENOTTY;
+ default:
+ return -ENOTTY;
}
}
if (pcipcwd_get_temperature(&temperature))
return -EFAULT;
- if (copy_to_user (data, &temperature, 1))
+ if (copy_to_user(data, &temperature, 1))
return -EFAULT;
return 1;
static int pcipcwd_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the WDT off */
- pcipcwd_stop();
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ pcipcwd_stop(); /* Turn the WDT off */
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = pcipcwd_write,
- .ioctl = pcipcwd_ioctl,
+ .unlocked_ioctl = pcipcwd_ioctl,
.open = pcipcwd_open,
.release = pcipcwd_release,
};
#include <linux/slab.h> /* For kmalloc, ... */
#include <linux/mutex.h> /* For mutex locking */
#include <linux/hid.h> /* For HID_REQ_SET_REPORT & HID_DT_REPORT */
-
-#include <asm/uaccess.h> /* For copy_to_user/put_user/... */
+#include <linux/uaccess.h> /* For copy_to_user/put_user/... */
#ifdef CONFIG_USB_DEBUG
#define USB_PCWD_PRODUCT_ID 0x1140
/* table of devices that work with this driver */
-static struct usb_device_id usb_pcwd_table [] = {
+static struct usb_device_id usb_pcwd_table[] = {
{ USB_DEVICE(USB_PCWD_VENDOR_ID, USB_PCWD_PRODUCT_ID) },
{ } /* Terminating entry */
};
#define CMD_DISABLE_WATCHDOG CMD_ENABLE_WATCHDOG
/* Watchdog's Dip Switch heartbeat values */
-static const int heartbeat_tbl [] = {
+static const int heartbeat_tbl[] = {
5, /* OFF-OFF-OFF = 5 Sec */
10, /* OFF-OFF-ON = 10 Sec */
30, /* OFF-ON-OFF = 30 Sec */
/* Structure to hold all of our device specific stuff */
struct usb_pcwd_private {
- struct usb_device * udev; /* save off the usb device pointer */
- struct usb_interface * interface; /* the interface for this device */
+ struct usb_device *udev; /* save off the usb device pointer */
+ struct usb_interface *interface; /* the interface for this device */
unsigned int interface_number; /* the interface number used for cmd's */
- unsigned char * intr_buffer; /* the buffer to intr data */
+ unsigned char *intr_buffer; /* the buffer to intr data */
dma_addr_t intr_dma; /* the dma address for the intr buffer */
size_t intr_size; /* the size of the intr buffer */
- struct urb * intr_urb; /* the urb used for the intr pipe */
+ struct urb *intr_urb; /* the urb used for the intr pipe */
unsigned char cmd_command; /* The command that is reported back */
unsigned char cmd_data_msb; /* The data MSB that is reported back */
static DEFINE_MUTEX(disconnect_mutex);
/* local function prototypes */
-static int usb_pcwd_probe (struct usb_interface *interface, const struct usb_device_id *id);
-static void usb_pcwd_disconnect (struct usb_interface *interface);
+static int usb_pcwd_probe(struct usb_interface *interface, const struct usb_device_id *id);
+static void usb_pcwd_disconnect(struct usb_interface *interface);
/* usb specific object needed to register this driver with the usb subsystem */
static struct usb_driver usb_pcwd_driver = {
usb_pcwd->cmd_data_lsb = data[2];
/* notify anyone waiting that the cmd has finished */
- atomic_set (&usb_pcwd->cmd_received, 1);
+ atomic_set(&usb_pcwd->cmd_received, 1);
resubmit:
- retval = usb_submit_urb (urb, GFP_ATOMIC);
+ retval = usb_submit_urb(urb, GFP_ATOMIC);
if (retval)
printk(KERN_ERR PFX "can't resubmit intr, usb_submit_urb failed with result %d\n",
retval);
dbg("sending following data cmd=0x%02x msb=0x%02x lsb=0x%02x",
buf[0], buf[1], buf[2]);
- atomic_set (&usb_pcwd->cmd_received, 0);
+ atomic_set(&usb_pcwd->cmd_received, 0);
if (usb_control_msg(usb_pcwd->udev, usb_sndctrlpipe(usb_pcwd->udev, 0),
HID_REQ_SET_REPORT, HID_DT_REPORT,
got_response = 0;
for (count = 0; (count < USB_COMMAND_TIMEOUT) && (!got_response); count++) {
mdelay(1);
- if (atomic_read (&usb_pcwd->cmd_received))
+ if (atomic_read(&usb_pcwd->cmd_received))
got_response = 1;
}
/* scan to see whether or not we got the magic character */
for (i = 0; i != len; i++) {
char c;
- if(get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_release = 42;
return len;
}
-static int usb_pcwd_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long usb_pcwd_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
};
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof (ident)) ? -EFAULT : 0;
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
- case WDIOC_GETTEMP:
- {
- int temperature;
+ case WDIOC_GETTEMP:
+ {
+ int temperature;
- if (usb_pcwd_get_temperature(usb_pcwd_device, &temperature))
- return -EFAULT;
+ if (usb_pcwd_get_temperature(usb_pcwd_device, &temperature))
+ return -EFAULT;
- return put_user(temperature, p);
- }
+ return put_user(temperature, p);
+ }
- case WDIOC_KEEPALIVE:
- usb_pcwd_keepalive(usb_pcwd_device);
- return 0;
+ case WDIOC_SETOPTIONS:
+ {
+ int new_options, retval = -EINVAL;
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
+ if (get_user(new_options, p))
+ return -EFAULT;
- if (get_user (new_options, p))
- return -EFAULT;
+ if (new_options & WDIOS_DISABLECARD) {
+ usb_pcwd_stop(usb_pcwd_device);
+ retval = 0;
+ }
- if (new_options & WDIOS_DISABLECARD) {
- usb_pcwd_stop(usb_pcwd_device);
- retval = 0;
- }
+ if (new_options & WDIOS_ENABLECARD) {
+ usb_pcwd_start(usb_pcwd_device);
+ retval = 0;
+ }
- if (new_options & WDIOS_ENABLECARD) {
- usb_pcwd_start(usb_pcwd_device);
- retval = 0;
- }
+ return retval;
+ }
- return retval;
- }
+ case WDIOC_KEEPALIVE:
+ usb_pcwd_keepalive(usb_pcwd_device);
+ return 0;
- case WDIOC_SETTIMEOUT:
- {
- int new_heartbeat;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_heartbeat;
- if (get_user(new_heartbeat, p))
- return -EFAULT;
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
- if (usb_pcwd_set_heartbeat(usb_pcwd_device, new_heartbeat))
- return -EINVAL;
+ if (usb_pcwd_set_heartbeat(usb_pcwd_device, new_heartbeat))
+ return -EINVAL;
- usb_pcwd_keepalive(usb_pcwd_device);
- /* Fall */
- }
+ usb_pcwd_keepalive(usb_pcwd_device);
+ /* Fall */
+ }
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
- case WDIOC_GETTIMELEFT:
- {
- int time_left;
+ case WDIOC_GETTIMELEFT:
+ {
+ int time_left;
- if (usb_pcwd_get_timeleft(usb_pcwd_device, &time_left))
- return -EFAULT;
+ if (usb_pcwd_get_timeleft(usb_pcwd_device, &time_left))
+ return -EFAULT;
- return put_user(time_left, p);
- }
+ return put_user(time_left, p);
+ }
- default:
- return -ENOTTY;
+ default:
+ return -ENOTTY;
}
}
static int usb_pcwd_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the WDT off */
- usb_pcwd_stop(usb_pcwd_device);
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ usb_pcwd_stop(usb_pcwd_device); /* Turn the WDT off */
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = usb_pcwd_write,
- .ioctl = usb_pcwd_ioctl,
+ .unlocked_ioctl = usb_pcwd_ioctl,
.open = usb_pcwd_open,
.release = usb_pcwd_release,
};
/**
* usb_pcwd_delete
*/
-static inline void usb_pcwd_delete (struct usb_pcwd_private *usb_pcwd)
+static inline void usb_pcwd_delete(struct usb_pcwd_private *usb_pcwd)
{
usb_free_urb(usb_pcwd->intr_urb);
if (usb_pcwd->intr_buffer != NULL)
usb_buffer_free(usb_pcwd->udev, usb_pcwd->intr_size,
usb_pcwd->intr_buffer, usb_pcwd->intr_dma);
- kfree (usb_pcwd);
+ kfree(usb_pcwd);
}
/**
maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe));
/* allocate memory for our device and initialize it */
- usb_pcwd = kzalloc (sizeof(struct usb_pcwd_private), GFP_KERNEL);
+ usb_pcwd = kzalloc(sizeof(struct usb_pcwd_private), GFP_KERNEL);
if (usb_pcwd == NULL) {
printk(KERN_ERR PFX "Out of memory\n");
goto error;
usb_pcwd->intr_size = (le16_to_cpu(endpoint->wMaxPacketSize) > 8 ? le16_to_cpu(endpoint->wMaxPacketSize) : 8);
/* set up the memory buffer's */
- if (!(usb_pcwd->intr_buffer = usb_buffer_alloc(udev, usb_pcwd->intr_size, GFP_ATOMIC, &usb_pcwd->intr_dma))) {
+ usb_pcwd->intr_buffer = usb_buffer_alloc(udev, usb_pcwd->intr_size, GFP_ATOMIC, &usb_pcwd->intr_dma);
+ if (!usb_pcwd->intr_buffer) {
printk(KERN_ERR PFX "Out of memory\n");
goto error;
}
/* Get the Firmware Version */
got_fw_rev = usb_pcwd_send_command(usb_pcwd, CMD_GET_FIRMWARE_VERSION, &fw_rev_major, &fw_rev_minor);
- if (got_fw_rev) {
+ if (got_fw_rev)
sprintf(fw_ver_str, "%u.%02u", fw_rev_major, fw_rev_minor);
- } else {
+ else
sprintf(fw_ver_str, "<card no answer>");
- }
printk(KERN_INFO PFX "Found card (Firmware: %s) with temp option\n",
fw_ver_str);
}
/* we can register the device now, as it is ready */
- usb_set_intfdata (interface, usb_pcwd);
+ usb_set_intfdata(interface, usb_pcwd);
printk(KERN_INFO PFX "initialized. heartbeat=%d sec (nowayout=%d)\n",
heartbeat, nowayout);
/* prevent races with open() */
mutex_lock(&disconnect_mutex);
- usb_pcwd = usb_get_intfdata (interface);
- usb_set_intfdata (interface, NULL);
+ usb_pcwd = usb_get_intfdata(interface);
+ usb_set_intfdata(interface, NULL);
mutex_lock(&usb_pcwd->mtx);
}
-module_init (usb_pcwd_init);
-module_exit (usb_pcwd_exit);
+module_init(usb_pcwd_init);
+module_exit(usb_pcwd_exit);
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/spinlock.h>
-
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+#include <mach/hardware.h>
#define MODULE_NAME "PNX4008-WDT: "
return nonseekable_open(inode, file);
}
-static ssize_t
-pnx4008_wdt_write(struct file *file, const char *data, size_t len,
- loff_t * ppos)
+static ssize_t pnx4008_wdt_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
if (len) {
if (!nowayout) {
return len;
}
-static struct watchdog_info ident = {
+static const struct watchdog_info ident = {
.options = WDIOF_CARDRESET | WDIOF_MAGICCLOSE |
WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
.identity = "PNX4008 Watchdog",
};
-static int
-pnx4008_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long pnx4008_wdt_ioctl(struct inode *inode, struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int ret = -ENOTTY;
int time;
ret = put_user(boot_status, (int *)arg);
break;
+ case WDIOC_KEEPALIVE:
+ wdt_enable();
+ ret = 0;
+ break;
+
case WDIOC_SETTIMEOUT:
ret = get_user(time, (int *)arg);
if (ret)
case WDIOC_GETTIMEOUT:
ret = put_user(heartbeat, (int *)arg);
break;
-
- case WDIOC_KEEPALIVE:
- wdt_enable();
- ret = 0;
- break;
}
return ret;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = pnx4008_wdt_write,
- .ioctl = pnx4008_wdt_ioctl,
+ .unlocked_ioctl = pnx4008_wdt_ioctl,
.open = pnx4008_wdt_open,
.release = pnx4008_wdt_release,
};
#include <linux/notifier.h>
#include <linux/miscdevice.h>
#include <linux/watchdog.h>
-#include <asm/io.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#include <asm/atomic.h>
#include <asm/processor.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#include <asm/rm9k-ocd.h>
static void wdt_gpi_set_timeout(unsigned int);
static int wdt_gpi_open(struct inode *, struct file *);
static int wdt_gpi_release(struct inode *, struct file *);
-static ssize_t wdt_gpi_write(struct file *, const char __user *, size_t, loff_t *);
+static ssize_t wdt_gpi_write(struct file *, const char __user *, size_t,
+ loff_t *);
static long wdt_gpi_ioctl(struct file *, unsigned int, unsigned long);
static int wdt_gpi_notify(struct notifier_block *, unsigned long, void *);
-static const struct resource *wdt_gpi_get_resource(struct platform_device *, const char *, unsigned int);
+static const struct resource *wdt_gpi_get_resource(struct platform_device *,
+ const char *, unsigned int);
static int __init wdt_gpi_probe(struct device *);
static int __exit wdt_gpi_remove(struct device *);
/* These are set from device resources */
-static void __iomem * wd_regs;
+static void __iomem *wd_regs;
static unsigned int wd_irq, wd_ctr;
if (expect_close) {
wdt_gpi_stop();
free_irq(wd_irq, &miscdev);
- printk(KERN_INFO "%s: watchdog stopped\n", wdt_gpi_name);
+ printk(KERN_INFO "%s: watchdog stopped\n",
+ wdt_gpi_name);
} else {
printk(KERN_CRIT "%s: unexpected close() -"
" watchdog left running\n",
return 0;
}
-static ssize_t
-wdt_gpi_write(struct file *f, const char __user *d, size_t s, loff_t *o)
+static ssize_t wdt_gpi_write(struct file *f, const char __user *d, size_t s,
+ loff_t *o)
{
char val;
return s ? 1 : 0;
}
-static long
-wdt_gpi_ioctl(struct file *f, unsigned int cmd, unsigned long arg)
+static long wdt_gpi_ioctl(struct file *f, unsigned int cmd, unsigned long arg)
{
long res = -ENOTTY;
const long size = _IOC_SIZE(cmd);
case WDIOC_GETSUPPORT:
wdinfo.options = nowayout ?
WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING :
- WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE;
+ WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING |
+ WDIOF_MAGICCLOSE;
res = __copy_to_user(argp, &wdinfo, size) ? -EFAULT : size;
break;
/* Shutdown notifier */
-static int
-wdt_gpi_notify(struct notifier_block *this, unsigned long code, void *unused)
+static int wdt_gpi_notify(struct notifier_block *this, unsigned long code,
+ void *unused)
{
if (code == SYS_DOWN || code == SYS_HALT)
wdt_gpi_stop();
/* Init & exit procedures */
-static const struct resource *
-wdt_gpi_get_resource(struct platform_device *pdv, const char *name,
- unsigned int type)
+static const struct resource *wdt_gpi_get_resource(struct platform_device *pdv,
+ const char *name, unsigned int type)
{
char buf[80];
if (snprintf(buf, sizeof buf, "%s_0", name) >= sizeof buf)
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/clk.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
-
-#include <asm/arch/map.h>
+#include <mach/map.h>
#undef S3C_VA_WATCHDOG
#define S3C_VA_WATCHDOG (0)
static int nowayout = WATCHDOG_NOWAYOUT;
static int tmr_margin = CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME;
static int tmr_atboot = CONFIG_S3C2410_WATCHDOG_ATBOOT;
-static int soft_noboot = 0;
-static int debug = 0;
+static int soft_noboot;
+static int debug;
module_param(tmr_margin, int, 0);
module_param(tmr_atboot, int, 0);
module_param(soft_noboot, int, 0);
module_param(debug, int, 0);
-MODULE_PARM_DESC(tmr_margin, "Watchdog tmr_margin in seconds. default=" __MODULE_STRING(CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME) ")");
-
-MODULE_PARM_DESC(tmr_atboot, "Watchdog is started at boot time if set to 1, default=" __MODULE_STRING(CONFIG_S3C2410_WATCHDOG_ATBOOT));
-
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
-
+MODULE_PARM_DESC(tmr_margin, "Watchdog tmr_margin in seconds. default="
+ __MODULE_STRING(CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME) ")");
+MODULE_PARM_DESC(tmr_atboot,
+ "Watchdog is started at boot time if set to 1, default="
+ __MODULE_STRING(CONFIG_S3C2410_WATCHDOG_ATBOOT));
+MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
MODULE_PARM_DESC(soft_noboot, "Watchdog action, set to 1 to ignore reboots, 0 to reboot (default depends on ONLY_TESTING)");
-
MODULE_PARM_DESC(debug, "Watchdog debug, set to >1 for debug, (default 0)");
typedef enum close_state {
CLOSE_STATE_NOT,
- CLOSE_STATE_ALLOW=0x4021
+ CLOSE_STATE_ALLOW = 0x4021
} close_state_t;
-static DECLARE_MUTEX(open_lock);
-
+static unsigned long open_lock;
static struct device *wdt_dev; /* platform device attached to */
static struct resource *wdt_mem;
static struct resource *wdt_irq;
static void __iomem *wdt_base;
static unsigned int wdt_count;
static close_state_t allow_close;
+static DEFINE_SPINLOCK(wdt_lock);
/* watchdog control routines */
#define DBG(msg...) do { \
if (debug) \
printk(KERN_INFO msg); \
- } while(0)
+ } while (0)
/* functions */
-static int s3c2410wdt_keepalive(void)
+static void s3c2410wdt_keepalive(void)
{
+ spin_lock(&wdt_lock);
writel(wdt_count, wdt_base + S3C2410_WTCNT);
- return 0;
+ spin_unlock(&wdt_lock);
}
-static int s3c2410wdt_stop(void)
+static void __s3c2410wdt_stop(void)
{
unsigned long wtcon;
wtcon = readl(wdt_base + S3C2410_WTCON);
wtcon &= ~(S3C2410_WTCON_ENABLE | S3C2410_WTCON_RSTEN);
writel(wtcon, wdt_base + S3C2410_WTCON);
+}
- return 0;
+static void s3c2410wdt_stop(void)
+{
+ spin_lock(&wdt_lock);
+ __s3c2410wdt_stop();
+ spin_unlock(&wdt_lock);
}
-static int s3c2410wdt_start(void)
+static void s3c2410wdt_start(void)
{
unsigned long wtcon;
- s3c2410wdt_stop();
+ spin_lock(&wdt_lock);
+
+ __s3c2410wdt_stop();
wtcon = readl(wdt_base + S3C2410_WTCON);
wtcon |= S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV128;
writel(wdt_count, wdt_base + S3C2410_WTDAT);
writel(wdt_count, wdt_base + S3C2410_WTCNT);
writel(wtcon, wdt_base + S3C2410_WTCON);
+ spin_unlock(&wdt_lock);
return 0;
}
static int s3c2410wdt_open(struct inode *inode, struct file *file)
{
- if(down_trylock(&open_lock))
+ if (test_and_set_bit(0, &open_lock))
return -EBUSY;
if (nowayout)
* Lock it in if it's a module and we set nowayout
*/
- if (allow_close == CLOSE_STATE_ALLOW) {
+ if (allow_close == CLOSE_STATE_ALLOW)
s3c2410wdt_stop();
- } else {
+ else {
dev_err(wdt_dev, "Unexpected close, not stopping watchdog\n");
s3c2410wdt_keepalive();
}
-
allow_close = CLOSE_STATE_NOT;
- up(&open_lock);
+ clear_bit(0, &open_lock);
return 0;
}
/*
* Refresh the timer.
*/
- if(len) {
+ if (len) {
if (!nowayout) {
size_t i;
allow_close = CLOSE_STATE_ALLOW;
}
}
-
s3c2410wdt_keepalive();
}
return len;
#define OPTIONS WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE
-static struct watchdog_info s3c2410_wdt_ident = {
+static const struct watchdog_info s3c2410_wdt_ident = {
.options = OPTIONS,
.firmware_version = 0,
.identity = "S3C2410 Watchdog",
};
-static int s3c2410wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long s3c2410wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_margin;
switch (cmd) {
- default:
- return -ENOTTY;
-
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &s3c2410_wdt_ident,
- sizeof(s3c2410_wdt_ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- s3c2410wdt_keepalive();
- return 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_margin, p))
- return -EFAULT;
-
- if (s3c2410wdt_set_heartbeat(new_margin))
- return -EINVAL;
-
- s3c2410wdt_keepalive();
- return put_user(tmr_margin, p);
-
- case WDIOC_GETTIMEOUT:
- return put_user(tmr_margin, p);
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &s3c2410_wdt_ident,
+ sizeof(s3c2410_wdt_ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ s3c2410wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_margin, p))
+ return -EFAULT;
+ if (s3c2410wdt_set_heartbeat(new_margin))
+ return -EINVAL;
+ s3c2410wdt_keepalive();
+ return put_user(tmr_margin, p);
+ case WDIOC_GETTIMEOUT:
+ return put_user(tmr_margin, p);
+ default:
+ return -ENOTTY;
}
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = s3c2410wdt_write,
- .ioctl = s3c2410wdt_ioctl,
+ .unlocked_ioctl = s3c2410wdt_ioctl,
.open = s3c2410wdt_open,
.release = s3c2410wdt_release,
};
* not, try the default value */
if (s3c2410wdt_set_heartbeat(tmr_margin)) {
- started = s3c2410wdt_set_heartbeat(CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME);
+ started = s3c2410wdt_set_heartbeat(
+ CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME);
- if (started == 0) {
- dev_info(dev,"tmr_margin value out of range, default %d used\n",
+ if (started == 0)
+ dev_info(dev,
+ "tmr_margin value out of range, default %d used\n",
CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME);
- } else {
+ else
dev_info(dev, "default timer value is out of range, cannot start\n");
- }
}
ret = misc_register(&s3c2410wdt_miscdev);
(wtcon & S3C2410_WTCON_ENABLE) ? "" : "in",
(wtcon & S3C2410_WTCON_RSTEN) ? "" : "dis",
(wtcon & S3C2410_WTCON_INTEN) ? "" : "en");
-
+
return 0;
err_clk:
static void s3c2410wdt_shutdown(struct platform_device *dev)
{
- s3c2410wdt_stop();
+ s3c2410wdt_stop();
}
#ifdef CONFIG_PM
};
-static char banner[] __initdata = KERN_INFO "S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics\n";
+static char banner[] __initdata =
+ KERN_INFO "S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics\n";
static int __init watchdog_init(void)
{
#include <linux/watchdog.h>
#include <linux/init.h>
#include <linux/bitops.h>
+#include <linux/uaccess.h>
#ifdef CONFIG_ARCH_PXA
-#include <asm/arch/pxa-regs.h>
+#include <mach/pxa-regs.h>
#endif
-#include <asm/hardware.h>
-#include <asm/uaccess.h>
+#include <mach/reset.h>
+#include <mach/hardware.h>
#define OSCR_FREQ CLOCK_TICK_RATE
*/
static int sa1100dog_open(struct inode *inode, struct file *file)
{
- if (test_and_set_bit(1,&sa1100wdt_users))
+ if (test_and_set_bit(1, &sa1100wdt_users))
return -EBUSY;
/* Activate SA1100 Watchdog timer */
static int sa1100dog_release(struct inode *inode, struct file *file)
{
printk(KERN_CRIT "WATCHDOG: Device closed - timer will not stop\n");
-
clear_bit(1, &sa1100wdt_users);
-
return 0;
}
-static ssize_t sa1100dog_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
+static ssize_t sa1100dog_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
if (len)
/* Refresh OSMR3 timer. */
OSMR3 = OSCR + pre_margin;
-
return len;
}
-static struct watchdog_info ident = {
- .options = WDIOF_CARDRESET | WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
+static const struct watchdog_info ident = {
+ .options = WDIOF_CARDRESET | WDIOF_SETTIMEOUT
+ | WDIOF_KEEPALIVEPING,
.identity = "SA1100/PXA255 Watchdog",
};
-static int sa1100dog_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long sa1100dog_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int ret = -ENOTTY;
int time;
ret = put_user(boot_status, p);
break;
+ case WDIOC_KEEPALIVE:
+ OSMR3 = OSCR + pre_margin;
+ ret = 0;
+ break;
+
case WDIOC_SETTIMEOUT:
ret = get_user(time, p);
if (ret)
case WDIOC_GETTIMEOUT:
ret = put_user(pre_margin / OSCR_FREQ, p);
break;
-
- case WDIOC_KEEPALIVE:
- OSMR3 = OSCR + pre_margin;
- ret = 0;
- break;
}
return ret;
}
-static const struct file_operations sa1100dog_fops =
-{
+static const struct file_operations sa1100dog_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = sa1100dog_write,
- .ioctl = sa1100dog_ioctl,
+ .unlocked_ioctl = sa1100dog_ioctl,
.open = sa1100dog_open,
.release = sa1100dog_release,
};
-static struct miscdevice sa1100dog_miscdev =
-{
+static struct miscdevice sa1100dog_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &sa1100dog_fops,
* we suspend, RCSR will be cleared, and the watchdog
* reset reason will be lost.
*/
- boot_status = (RCSR & RCSR_WDR) ? WDIOF_CARDRESET : 0;
+ boot_status = (reset_status & RESET_STATUS_WATCHDOG) ?
+ WDIOF_CARDRESET : 0;
pre_margin = OSCR_FREQ * margin;
ret = misc_register(&sa1100dog_miscdev);
if (ret == 0)
- printk("SA1100/PXA2xx Watchdog Timer: timer margin %d sec\n",
- margin);
+ printk(KERN_INFO
+ "SA1100/PXA2xx Watchdog Timer: timer margin %d sec\n",
+ margin);
return ret;
}
#include <asm/sibyte/sb1250_int.h>
#include <asm/sibyte/sb1250_scd.h>
+static DEFINE_SPINLOCK(sbwd_lock);
/*
* set the initial count value of a timer
*/
void sbwdog_set(char __iomem *wdog, unsigned long t)
{
+ spin_lock(&sbwd_lock);
__raw_writeb(0, wdog - 0x10);
__raw_writeq(t & 0x7fffffUL, wdog);
+ spin_unlock(&sbwd_lock);
}
/*
*/
void sbwdog_pet(char __iomem *wdog)
{
+ spin_lock(&sbwd_lock);
__raw_writeb(__raw_readb(wdog) | 1, wdog);
+ spin_unlock(&sbwd_lock);
}
static unsigned long sbwdog_gate; /* keeps it to one thread only */
static unsigned long timeout = 0x7fffffUL; /* useconds: 8.3ish secs. */
static int expect_close;
-static struct watchdog_info ident = {
- .options = WDIOF_CARDRESET | WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
+static const struct watchdog_info ident = {
+ .options = WDIOF_CARDRESET | WDIOF_SETTIMEOUT |
+ WDIOF_KEEPALIVEPING,
.identity = "SiByte Watchdog",
};
static int sbwdog_open(struct inode *inode, struct file *file)
{
nonseekable_open(inode, file);
- if (test_and_set_bit(0, &sbwdog_gate)) {
+ if (test_and_set_bit(0, &sbwdog_gate))
return -EBUSY;
- }
__module_get(THIS_MODULE);
/*
__raw_writeb(0, user_dog);
module_put(THIS_MODULE);
} else {
- printk(KERN_CRIT "%s: Unexpected close, not stopping watchdog!\n",
- ident.identity);
+ printk(KERN_CRIT
+ "%s: Unexpected close, not stopping watchdog!\n",
+ ident.identity);
sbwdog_pet(user_dog);
}
clear_bit(0, &sbwdog_gate);
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data + i)) {
+ if (get_user(c, data + i))
return -EFAULT;
- }
- if (c == 'V') {
+ if (c == 'V')
expect_close = 42;
- }
}
sbwdog_pet(user_dog);
}
return len;
}
-static int sbwdog_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long sbwdog_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int ret = -ENOTTY;
unsigned long time;
ret = put_user(0, p);
break;
+ case WDIOC_KEEPALIVE:
+ sbwdog_pet(user_dog);
+ ret = 0;
+ break;
+
case WDIOC_SETTIMEOUT:
ret = get_user(time, p);
- if (ret) {
+ if (ret)
break;
- }
time *= 1000000;
if (time > 0x7fffffUL) {
*/
ret = put_user(__raw_readq(user_dog - 8) / 1000000, p);
break;
-
- case WDIOC_KEEPALIVE:
- sbwdog_pet(user_dog);
- ret = 0;
- break;
}
return ret;
}
/*
* Notifier for system down
*/
-static int
-sbwdog_notify_sys(struct notifier_block *this, unsigned long code, void *erf)
+static int sbwdog_notify_sys(struct notifier_block *this, unsigned long code,
+ void *erf)
{
if (code == SYS_DOWN || code == SYS_HALT) {
/*
return NOTIFY_DONE;
}
-static const struct file_operations sbwdog_fops =
-{
+static const struct file_operations sbwdog_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = sbwdog_write,
- .ioctl = sbwdog_ioctl,
+ .unlocked_ioctl = sbwdog_ioctl,
.open = sbwdog_open,
.release = sbwdog_release,
};
-static struct miscdevice sbwdog_miscdev =
-{
+static struct miscdevice sbwdog_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &sbwdog_fops,
/*
* if it's the second watchdog timer, it's for those users
*/
- if (wd_cfg_reg == user_dog) {
+ if (wd_cfg_reg == user_dog)
printk(KERN_CRIT
"%s in danger of initiating system reset in %ld.%01ld seconds\n",
ident.identity, wd_init / 1000000, (wd_init / 100000) % 10);
- } else {
+ else
cfg |= 1;
- }
__raw_writeb(cfg, wd_cfg_reg);
*/
ret = register_reboot_notifier(&sbwdog_notifier);
if (ret) {
- printk (KERN_ERR "%s: cannot register reboot notifier (err=%d)\n",
- ident.identity, ret);
+ printk(KERN_ERR
+ "%s: cannot register reboot notifier (err=%d)\n",
+ ident.identity, ret);
return ret;
}
/*
* get the resources
*/
- ret = misc_register(&sbwdog_miscdev);
- if (ret == 0) {
- printk(KERN_INFO "%s: timeout is %ld.%ld secs\n", ident.identity,
- timeout / 1000000, (timeout / 100000) % 10);
- }
ret = request_irq(1, sbwdog_interrupt, IRQF_DISABLED | IRQF_SHARED,
ident.identity, (void *)user_dog);
if (ret) {
- printk(KERN_ERR "%s: failed to request irq 1 - %d\n", ident.identity,
- ret);
- misc_deregister(&sbwdog_miscdev);
+ printk(KERN_ERR "%s: failed to request irq 1 - %d\n",
+ ident.identity, ret);
+ return ret;
}
+ ret = misc_register(&sbwdog_miscdev);
+ if (ret == 0) {
+ printk(KERN_INFO "%s: timeout is %ld.%ld secs\n",
+ ident.identity,
+ timeout / 1000000, (timeout / 100000) % 10);
+ } else
+ free_irq(1, (void *)user_dog);
return ret;
}
module_param(timeout, ulong, 0);
MODULE_PARM_DESC(timeout,
- "Watchdog timeout in microseconds (max/default 8388607 or 8.3ish secs)");
+ "Watchdog timeout in microseconds (max/default 8388607 or 8.3ish secs)");
MODULE_LICENSE("GPL");
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
* example code that can be put in a platform code area to utilize the
* first watchdog timer for the kernels own purpose.
- void
-platform_wd_setup(void)
+void platform_wd_setup(void)
{
int ret;
- ret = request_irq(0, sbwdog_interrupt, IRQF_DISABLED | IRQF_SHARED,
+ ret = request_irq(1, sbwdog_interrupt, IRQF_DISABLED | IRQF_SHARED,
"Kernel Watchdog", IOADDR(A_SCD_WDOG_CFG_0));
if (ret) {
- printk(KERN_CRIT "Watchdog IRQ zero(0) failed to be requested - %d\n",
- ret);
+ printk(KERN_CRIT
+ "Watchdog IRQ zero(0) failed to be requested - %d\n", ret);
}
}
*
* 12/4 - 2000 [Initial revision]
* 25/4 - 2000 Added /dev/watchdog support
- * 09/5 - 2001 [smj@oro.net] fixed fop_write to "return 1" on success
+ * 09/5 - 2001 [smj@oro.net] fixed fop_write to "return 1"
+ * on success
* 12/4 - 2002 [rob@osinvestor.com] eliminate fop_read
* fix possible wdt_is_open race
* add CONFIG_WATCHDOG_NOWAYOUT support
* remove lock_kernel/unlock_kernel pairs
* added KERN_* to printk's
* got rid of extraneous comments
- * changed watchdog_info to correctly reflect what the driver offers
- * added WDIOC_GETSTATUS, WDIOC_GETBOOTSTATUS, WDIOC_SETTIMEOUT,
- * WDIOC_GETTIMEOUT, and WDIOC_SETOPTIONS ioctls
+ * changed watchdog_info to correctly reflect what
+ * the driver offers
+ * added WDIOC_GETSTATUS, WDIOC_GETBOOTSTATUS,
+ * WDIOC_SETTIMEOUT, WDIOC_GETTIMEOUT, and
+ * WDIOC_SETOPTIONS ioctls
* 09/8 - 2003 [wim@iguana.be] cleanup of trailing spaces
* use module_param
- * made timeout (the emulated heartbeat) a module_param
+ * made timeout (the emulated heartbeat) a
+ * module_param
* made the keepalive ping an internal subroutine
* made wdt_stop and wdt_start module params
* added extra printk's for startup problems
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define OUR_NAME "sbc60xxwdt"
*/
#define WATCHDOG_TIMEOUT 30 /* 30 sec default timeout */
-static int timeout = WATCHDOG_TIMEOUT; /* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+static int timeout = WATCHDOG_TIMEOUT; /* in seconds, multiplied by HZ to
+ get seconds to wait for a ping */
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=3600, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1<=timeout<=3600, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static void wdt_timer_ping(unsigned long);
static DEFINE_TIMER(timer, wdt_timer_ping, 0, 0);
/* If we got a heartbeat pulse within the WDT_US_INTERVAL
* we agree to ping the WDT
*/
- if(time_before(jiffies, next_heartbeat))
- {
+ if (time_before(jiffies, next_heartbeat)) {
/* Ping the WDT by reading from wdt_start */
inb_p(wdt_start);
/* Re-set the timer interval */
mod_timer(&timer, jiffies + WDT_INTERVAL);
- } else {
- printk(KERN_WARNING PFX "Heartbeat lost! Will not ping the watchdog\n");
- }
+ } else
+ printk(KERN_WARNING PFX
+ "Heartbeat lost! Will not ping the watchdog\n");
}
/*
* /dev/watchdog handling
*/
-static ssize_t fop_write(struct file * file, const char __user * buf, size_t count, loff_t * ppos)
+static ssize_t fop_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count)
- {
- if (!nowayout)
- {
+ if (count) {
+ if (!nowayout) {
size_t ofs;
- /* note: just in case someone wrote the magic character
- * five months ago... */
+ /* note: just in case someone wrote the
+ magic character five months ago... */
wdt_expect_close = 0;
- /* scan to see whether or not we got the magic character */
- for(ofs = 0; ofs != count; ofs++)
- {
+ /* scan to see whether or not we got the
+ magic character */
+ for (ofs = 0; ofs != count; ofs++) {
char c;
- if(get_user(c, buf+ofs))
+ if (get_user(c, buf + ofs))
return -EFAULT;
- if(c == 'V')
+ if (c == 'V')
wdt_expect_close = 42;
}
}
- /* Well, anyhow someone wrote to us, we should return that favour */
+ /* Well, anyhow someone wrote to us, we should
+ return that favour */
wdt_keepalive();
}
return count;
}
-static int fop_open(struct inode * inode, struct file * file)
+static int fop_open(struct inode *inode, struct file *file)
{
/* Just in case we're already talking to someone... */
- if(test_and_set_bit(0, &wdt_is_open))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
if (nowayout)
return nonseekable_open(inode, file);
}
-static int fop_close(struct inode * inode, struct file * file)
+static int fop_close(struct inode *inode, struct file *file)
{
- if(wdt_expect_close == 42)
+ if (wdt_expect_close == 42)
wdt_turnoff();
else {
del_timer(&timer);
- printk(KERN_CRIT PFX "device file closed unexpectedly. Will not stop the WDT!\n");
+ printk(KERN_CRIT PFX
+ "device file closed unexpectedly. Will not stop the WDT!\n");
}
clear_bit(0, &wdt_is_open);
wdt_expect_close = 0;
return 0;
}
-static int fop_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long fop_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident=
- {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "SBC60xx",
};
- switch(cmd)
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
{
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if(get_user(new_options, p))
- return -EFAULT;
-
- if(new_options & WDIOS_DISABLECARD) {
- wdt_turnoff();
- retval = 0;
- }
-
- if(new_options & WDIOS_ENABLECARD) {
- wdt_startup();
- retval = 0;
- }
-
- return retval;
+ int new_options, retval = -EINVAL;
+ if (get_user(new_options, p))
+ return -EFAULT;
+ if (new_options & WDIOS_DISABLECARD) {
+ wdt_turnoff();
+ retval = 0;
}
- case WDIOC_SETTIMEOUT:
- {
- int new_timeout;
-
- if(get_user(new_timeout, p))
- return -EFAULT;
-
- if(new_timeout < 1 || new_timeout > 3600) /* arbitrary upper limit */
- return -EINVAL;
-
- timeout = new_timeout;
- wdt_keepalive();
- /* Fall through */
+ if (new_options & WDIOS_ENABLECARD) {
+ wdt_startup();
+ retval = 0;
}
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ /* arbitrary upper limit */
+ if (new_timeout < 1 || new_timeout > 3600)
+ return -EINVAL;
+
+ timeout = new_timeout;
+ wdt_keepalive();
+ /* Fall through */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
.write = fop_write,
.open = fop_open,
.release = fop_close,
- .ioctl = fop_ioctl,
+ .unlocked_ioctl = fop_ioctl,
};
static struct miscdevice wdt_miscdev = {
static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_turnoff();
return NOTIFY_DONE;
}
* turn the timebomb registers off.
*/
-static struct notifier_block wdt_notifier=
-{
+static struct notifier_block wdt_notifier = {
.notifier_call = wdt_notify_sys,
};
unregister_reboot_notifier(&wdt_notifier);
if ((wdt_stop != 0x45) && (wdt_stop != wdt_start))
- release_region(wdt_stop,1);
- release_region(wdt_start,1);
+ release_region(wdt_stop, 1);
+ release_region(wdt_start, 1);
}
static int __init sbc60xxwdt_init(void)
{
int rc = -EBUSY;
- if(timeout < 1 || timeout > 3600) /* arbitrary upper limit */
- {
+ if (timeout < 1 || timeout > 3600) { /* arbitrary upper limit */
timeout = WATCHDOG_TIMEOUT;
- printk(KERN_INFO PFX "timeout value must be 1<=x<=3600, using %d\n",
- timeout);
- }
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= x <= 3600, using %d\n",
+ timeout);
+ }
- if (!request_region(wdt_start, 1, "SBC 60XX WDT"))
- {
+ if (!request_region(wdt_start, 1, "SBC 60XX WDT")) {
printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
wdt_start);
rc = -EIO;
}
/* We cannot reserve 0x45 - the kernel already has! */
- if ((wdt_stop != 0x45) && (wdt_stop != wdt_start))
- {
- if (!request_region(wdt_stop, 1, "SBC 60XX WDT"))
- {
- printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
- wdt_stop);
+ if (wdt_stop != 0x45 && wdt_stop != wdt_start) {
+ if (!request_region(wdt_stop, 1, "SBC 60XX WDT")) {
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n",
+ wdt_stop);
rc = -EIO;
goto err_out_region1;
}
}
rc = register_reboot_notifier(&wdt_notifier);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out_region2;
}
rc = misc_register(&wdt_miscdev);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- wdt_miscdev.minor, rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ wdt_miscdev.minor, rc);
goto err_out_reboot;
}
-
printk(KERN_INFO PFX "WDT driver for 60XX single board computer initialised. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
err_out_reboot:
unregister_reboot_notifier(&wdt_notifier);
err_out_region2:
- if ((wdt_stop != 0x45) && (wdt_stop != wdt_start))
- release_region(wdt_stop,1);
+ if (wdt_stop != 0x45 && wdt_stop != wdt_start)
+ release_region(wdt_stop, 1);
err_out_region1:
- release_region(wdt_start,1);
+ release_region(wdt_start, 1);
err_out:
return rc;
}
#include <linux/reboot.h>
#include <linux/types.h>
#include <linux/watchdog.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#include <asm/atomic.h>
-#include <asm/io.h>
#include <asm/system.h>
-#include <asm/uaccess.h>
#define SBC7240_PREFIX "sbc7240_wdt: "
return 0;
}
-static struct watchdog_info ident = {
+static const struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING|
WDIOF_SETTIMEOUT|
WDIOF_MAGICCLOSE,
};
-static int fop_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long fop_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
switch (cmd) {
case WDIOC_GETSUPPORT:
- return copy_to_user
- ((void __user *)arg, &ident, sizeof(ident))
- ? -EFAULT : 0;
+ return copy_to_user((void __user *)arg, &ident, sizeof(ident))
+ ? -EFAULT : 0;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
return put_user(0, (int __user *)arg);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
- case WDIOC_SETOPTIONS:{
- int options;
- int retval = -EINVAL;
+ case WDIOC_SETOPTIONS:
+ {
+ int options;
+ int retval = -EINVAL;
- if (get_user(options, (int __user *)arg))
- return -EFAULT;
+ if (get_user(options, (int __user *)arg))
+ return -EFAULT;
- if (options & WDIOS_DISABLECARD) {
- wdt_disable();
- retval = 0;
- }
-
- if (options & WDIOS_ENABLECARD) {
- wdt_enable();
- retval = 0;
- }
+ if (options & WDIOS_DISABLECARD) {
+ wdt_disable();
+ retval = 0;
+ }
- return retval;
+ if (options & WDIOS_ENABLECARD) {
+ wdt_enable();
+ retval = 0;
}
- case WDIOC_SETTIMEOUT:{
- int new_timeout;
- if (get_user(new_timeout, (int __user *)arg))
- return -EFAULT;
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
- if (wdt_set_timeout(new_timeout))
- return -EINVAL;
+ if (get_user(new_timeout, (int __user *)arg))
+ return -EFAULT;
- /* Fall through */
- }
+ if (wdt_set_timeout(new_timeout))
+ return -EINVAL;
+
+ /* Fall through */
+ }
case WDIOC_GETTIMEOUT:
return put_user(timeout, (int __user *)arg);
default:
.write = fop_write,
.open = fop_open,
.release = fop_close,
- .ioctl = fop_ioctl,
+ .unlocked_ioctl = fop_ioctl,
};
static struct miscdevice wdt_miscdev = {
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/moduleparam.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
static unsigned long sbc8360_is_open;
-static DEFINE_SPINLOCK(sbc8360_lock);
static char expect_close;
#define PFX "sbc8360: "
MODULE_PARM_DESC(timeout, "Index into timeout table (0-63) (default=27 (60s))");
module_param(nowayout, int, 0);
MODULE_PARM_DESC(nowayout,
- "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Kernel methods.
outb(wd_margin, SBC8360_BASETIME);
}
+/* stop watchdog */
+static void sbc8360_stop(void)
+{
+ /* De-activate the watchdog */
+ outb(0, SBC8360_ENABLE);
+}
+
/* Userspace pings kernel driver, or requests clean close */
-static ssize_t sbc8360_write(struct file *file, const char __user * buf,
- size_t count, loff_t * ppos)
+static ssize_t sbc8360_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
static int sbc8360_open(struct inode *inode, struct file *file)
{
- spin_lock(&sbc8360_lock);
- if (test_and_set_bit(0, &sbc8360_is_open)) {
- spin_unlock(&sbc8360_lock);
+ if (test_and_set_bit(0, &sbc8360_is_open))
return -EBUSY;
- }
if (nowayout)
__module_get(THIS_MODULE);
/* Activate and ping once to start the countdown */
- spin_unlock(&sbc8360_lock);
sbc8360_activate();
sbc8360_ping();
return nonseekable_open(inode, file);
static int sbc8360_close(struct inode *inode, struct file *file)
{
- spin_lock(&sbc8360_lock);
if (expect_close == 42)
- outb(0, SBC8360_ENABLE);
+ sbc8360_stop();
else
printk(KERN_CRIT PFX
- "SBC8360 device closed unexpectedly. SBC8360 will not stop!\n");
+ "SBC8360 device closed unexpectedly. SBC8360 will not stop!\n");
clear_bit(0, &sbc8360_is_open);
expect_close = 0;
- spin_unlock(&sbc8360_lock);
return 0;
}
static int sbc8360_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT) {
- /* Disable the SBC8360 Watchdog */
- outb(0, SBC8360_ENABLE);
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ sbc8360_stop(); /* Disable the SBC8360 Watchdog */
+
return NOTIFY_DONE;
}
return 0;
- out_nomisc:
+out_nomisc:
unregister_reboot_notifier(&sbc8360_notifier);
- out_noreboot:
+out_noreboot:
release_region(SBC8360_BASETIME, 1);
- out_nobasetimereg:
+out_nobasetimereg:
release_region(SBC8360_ENABLE, 1);
- out:
+out:
return res;
}
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/ioport.h>
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#define PFX "epx_c3: "
static int epx_c3_alive;
return len;
}
-static int epx_c3_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long epx_c3_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int options, retval = -EINVAL;
int __user *argp = (void __user *)arg;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING |
WDIOF_MAGICCLOSE,
.firmware_version = 0,
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
return put_user(0, argp);
- case WDIOC_KEEPALIVE:
- epx_c3_pet();
- return 0;
- case WDIOC_GETTIMEOUT:
- return put_user(WATCHDOG_TIMEOUT, argp);
case WDIOC_SETOPTIONS:
if (get_user(options, argp))
return -EFAULT;
}
return retval;
+ case WDIOC_KEEPALIVE:
+ epx_c3_pet();
+ return 0;
+ case WDIOC_GETTIMEOUT:
+ return put_user(WATCHDOG_TIMEOUT, argp);
default:
return -ENOTTY;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = epx_c3_write,
- .ioctl = epx_c3_ioctl,
+ .unlocked_ioctl = epx_c3_ioctl,
.open = epx_c3_open,
.release = epx_c3_release,
};
*
* Changelog:
* 20020220 Zwane Mwaikambo Code based on datasheet, no hardware.
- * 20020221 Zwane Mwaikambo Cleanups as suggested by Jeff Garzik and Alan Cox.
+ * 20020221 Zwane Mwaikambo Cleanups as suggested by Jeff Garzik
+ * and Alan Cox.
* 20020222 Zwane Mwaikambo Added probing.
* 20020225 Zwane Mwaikambo Added ISAPNP support.
* 20020412 Rob Radez Broke out start/stop functions
- * <rob@osinvestor.com> Return proper status instead of temperature warning
- * Add WDIOC_GETBOOTSTATUS and WDIOC_SETOPTIONS ioctls
+ * <rob@osinvestor.com> Return proper status instead of
+ * temperature warning
+ * Add WDIOC_GETBOOTSTATUS and
+ * WDIOC_SETOPTIONS ioctls
* Fix CONFIG_WATCHDOG_NOWAYOUT
- * 20020530 Joel Becker Add Matt Domsch's nowayout module option
+ * 20020530 Joel Becker Add Matt Domsch's nowayout module
+ * option
* 20030116 Adam Belay Updated to the latest pnp code
*
*/
#include <linux/pnp.h>
#include <linux/fs.h>
#include <linux/semaphore.h>
-
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#define SC1200_MODULE_VER "build 20020303"
#define SC1200_MODULE_NAME "sc1200wdt"
static int timeout = 1;
static int io = -1;
static int io_len = 2; /* for non plug and play */
-static struct semaphore open_sem;
+static unsigned long open_flag;
static char expect_close;
static DEFINE_SPINLOCK(sc1200wdt_lock); /* io port access serialisation */
static struct pnp_dev *wdt_dev;
module_param(isapnp, int, 0);
-MODULE_PARM_DESC(isapnp, "When set to 0 driver ISA PnP support will be disabled");
+MODULE_PARM_DESC(isapnp,
+ "When set to 0 driver ISA PnP support will be disabled");
#endif
module_param(io, int, 0);
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/* Read from Data Register */
-static inline void sc1200wdt_read_data(unsigned char index, unsigned char *data)
+static inline void __sc1200wdt_read_data(unsigned char index,
+ unsigned char *data)
{
- spin_lock(&sc1200wdt_lock);
outb_p(index, PMIR);
*data = inb(PMDR);
- spin_unlock(&sc1200wdt_lock);
}
+static void sc1200wdt_read_data(unsigned char index, unsigned char *data)
+{
+ spin_lock(&sc1200wdt_lock);
+ __sc1200wdt_read_data(index, data);
+ spin_unlock(&sc1200wdt_lock);
+}
/* Write to Data Register */
-static inline void sc1200wdt_write_data(unsigned char index, unsigned char data)
+static inline void __sc1200wdt_write_data(unsigned char index,
+ unsigned char data)
{
- spin_lock(&sc1200wdt_lock);
outb_p(index, PMIR);
outb(data, PMDR);
+}
+
+static inline void sc1200wdt_write_data(unsigned char index,
+ unsigned char data)
+{
+ spin_lock(&sc1200wdt_lock);
+ __sc1200wdt_write_data(index, data);
spin_unlock(&sc1200wdt_lock);
}
static void sc1200wdt_start(void)
{
unsigned char reg;
+ spin_lock(&sc1200wdt_lock);
- sc1200wdt_read_data(WDCF, ®);
+ __sc1200wdt_read_data(WDCF, ®);
/* assert WDO when any of the following interrupts are triggered too */
reg |= (KBC_IRQ | MSE_IRQ | UART1_IRQ | UART2_IRQ);
- sc1200wdt_write_data(WDCF, reg);
+ __sc1200wdt_write_data(WDCF, reg);
/* set the timeout and get the ball rolling */
- sc1200wdt_write_data(WDTO, timeout);
-}
+ __sc1200wdt_write_data(WDTO, timeout);
+ spin_unlock(&sc1200wdt_lock);
+}
static void sc1200wdt_stop(void)
{
sc1200wdt_write_data(WDTO, 0);
}
-
/* This returns the status of the WDO signal, inactive high. */
static inline int sc1200wdt_status(void)
{
* KEEPALIVEPING which is a bit of a kludge because there's nothing
* else for enabled/disabled status
*/
- return (ret & 0x01) ? 0 : WDIOF_KEEPALIVEPING; /* bits 1 - 7 are undefined */
+ return (ret & 0x01) ? 0 : WDIOF_KEEPALIVEPING;
}
-
static int sc1200wdt_open(struct inode *inode, struct file *file)
{
/* allow one at a time */
- if (down_trylock(&open_sem))
+ if (test_and_set_bit(0, &open_flag))
return -EBUSY;
if (timeout > MAX_TIMEOUT)
}
-static int sc1200wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+static long sc1200wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_timeout;
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE,
.firmware_version = 0,
.identity = "PC87307/PC97307",
};
switch (cmd) {
- default:
- return -ENOTTY;
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &ident, sizeof ident))
+ return -EFAULT;
+ return 0;
- case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof ident))
- return -EFAULT;
- return 0;
+ case WDIOC_GETSTATUS:
+ return put_user(sc1200wdt_status(), p);
- case WDIOC_GETSTATUS:
- return put_user(sc1200wdt_status(), p);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
+ case WDIOC_SETOPTIONS:
+ {
+ int options, retval = -EINVAL;
- case WDIOC_KEEPALIVE:
- sc1200wdt_write_data(WDTO, timeout);
- return 0;
+ if (get_user(options, p))
+ return -EFAULT;
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, p))
- return -EFAULT;
-
- /* the API states this is given in secs */
- new_timeout /= 60;
- if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
- return -EINVAL;
-
- timeout = new_timeout;
- sc1200wdt_write_data(WDTO, timeout);
- /* fall through and return the new timeout */
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout * 60, p);
-
- case WDIOC_SETOPTIONS:
- {
- int options, retval = -EINVAL;
+ if (options & WDIOS_DISABLECARD) {
+ sc1200wdt_stop();
+ retval = 0;
+ }
- if (get_user(options, p))
- return -EFAULT;
+ if (options & WDIOS_ENABLECARD) {
+ sc1200wdt_start();
+ retval = 0;
+ }
- if (options & WDIOS_DISABLECARD) {
- sc1200wdt_stop();
- retval = 0;
- }
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ sc1200wdt_write_data(WDTO, timeout);
+ return 0;
+
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ /* the API states this is given in secs */
+ new_timeout /= 60;
+ if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
+ return -EINVAL;
+ timeout = new_timeout;
+ sc1200wdt_write_data(WDTO, timeout);
+ /* fall through and return the new timeout */
- if (options & WDIOS_ENABLECARD) {
- sc1200wdt_start();
- retval = 0;
- }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout * 60, p);
- return retval;
- }
+ default:
+ return -ENOTTY;
}
}
printk(KERN_INFO PFX "Watchdog disabled\n");
} else {
sc1200wdt_write_data(WDTO, timeout);
- printk(KERN_CRIT PFX "Unexpected close!, timeout = %d min(s)\n", timeout);
+ printk(KERN_CRIT PFX
+ "Unexpected close!, timeout = %d min(s)\n", timeout);
}
- up(&open_sem);
+ clear_bit(0, &open_flag);
expect_close = 0;
return 0;
}
-static ssize_t sc1200wdt_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
+static ssize_t sc1200wdt_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
if (len) {
if (!nowayout) {
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
}
-static int sc1200wdt_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int sc1200wdt_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
if (code == SYS_DOWN || code == SYS_HALT)
sc1200wdt_stop();
}
-static struct notifier_block sc1200wdt_notifier =
-{
+static struct notifier_block sc1200wdt_notifier = {
.notifier_call = sc1200wdt_notify_sys,
};
-static const struct file_operations sc1200wdt_fops =
-{
+static const struct file_operations sc1200wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = sc1200wdt_write,
- .ioctl = sc1200wdt_ioctl,
+ .unlocked_ioctl = sc1200wdt_ioctl,
.open = sc1200wdt_open,
.release = sc1200wdt_release,
};
-static struct miscdevice sc1200wdt_miscdev =
-{
+static struct miscdevice sc1200wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &sc1200wdt_fops,
/* The probe works by reading the PMC3 register's default value of 0x0e
* there is one caveat, if the device disables the parallel port or any
* of the UARTs we won't be able to detect it.
- * Nb. This could be done with accuracy by reading the SID registers, but
- * we don't have access to those io regions.
+ * NB. This could be done with accuracy by reading the SID registers,
+ * but we don't have access to those io regions.
*/
unsigned char reg;
sc1200wdt_read_data(PMC3, ®);
- reg &= 0x0f; /* we don't want the UART busy bits */
+ reg &= 0x0f; /* we don't want the UART busy bits */
return (reg == 0x0e) ? 0 : -ENODEV;
}
{.id = ""},
};
-static int scl200wdt_pnp_probe(struct pnp_dev * dev, const struct pnp_device_id *dev_id)
+static int scl200wdt_pnp_probe(struct pnp_dev *dev,
+ const struct pnp_device_id *dev_id)
{
/* this driver only supports one card at a time */
if (wdt_dev || !isapnp)
return -EBUSY;
}
- printk(KERN_INFO "scl200wdt: PnP device found at io port %#x/%d\n", io, io_len);
+ printk(KERN_INFO "scl200wdt: PnP device found at io port %#x/%d\n",
+ io, io_len);
return 0;
}
-static void scl200wdt_pnp_remove(struct pnp_dev * dev)
+static void scl200wdt_pnp_remove(struct pnp_dev *dev)
{
- if (wdt_dev){
+ if (wdt_dev) {
release_region(io, io_len);
wdt_dev = NULL;
}
printk("%s\n", banner);
- sema_init(&open_sem, 1);
-
#if defined CONFIG_PNP
if (isapnp) {
ret = pnp_register_driver(&scl200wdt_pnp_driver);
ret = register_reboot_notifier(&sc1200wdt_notifier);
if (ret) {
- printk(KERN_ERR PFX "Unable to register reboot notifier err = %d\n", ret);
+ printk(KERN_ERR PFX
+ "Unable to register reboot notifier err = %d\n", ret);
goto out_io;
}
ret = misc_register(&sc1200wdt_miscdev);
if (ret) {
- printk(KERN_ERR PFX "Unable to register miscdev on minor %d\n", WATCHDOG_MINOR);
+ printk(KERN_ERR PFX
+ "Unable to register miscdev on minor %d\n",
+ WATCHDOG_MINOR);
goto out_rbt;
}
unregister_reboot_notifier(&sc1200wdt_notifier);
#if defined CONFIG_PNP
- if(isapnp)
+ if (isapnp)
pnp_unregister_driver(&scl200wdt_pnp_driver);
else
#endif
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/jiffies.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define OUR_NAME "sc520_wdt"
*/
#define WATCHDOG_TIMEOUT 30 /* 30 sec default timeout */
-static int timeout = WATCHDOG_TIMEOUT; /* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+/* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+static int timeout = WATCHDOG_TIMEOUT;
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=3600, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1 <= timeout <= 3600, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* AMD Elan SC520 - Watchdog Timer Registers
/* If we got a heartbeat pulse within the WDT_US_INTERVAL
* we agree to ping the WDT
*/
- if(time_before(jiffies, next_heartbeat))
- {
+ if (time_before(jiffies, next_heartbeat)) {
/* Ping the WDT */
spin_lock(&wdt_spinlock);
writew(0xAAAA, wdtmrctl);
/* Re-set the timer interval */
mod_timer(&timer, jiffies + WDT_INTERVAL);
- } else {
- printk(KERN_WARNING PFX "Heartbeat lost! Will not ping the watchdog\n");
- }
+ } else
+ printk(KERN_WARNING PFX
+ "Heartbeat lost! Will not ping the watchdog\n");
}
/*
/* buy some time (ping) */
spin_lock_irqsave(&wdt_spinlock, flags);
- dummy=readw(wdtmrctl); /* ensure write synchronization */
+ dummy = readw(wdtmrctl); /* ensure write synchronization */
writew(0xAAAA, wdtmrctl);
writew(0x5555, wdtmrctl);
/* unlock WDT = make WDT configuration register writable one time */
* /dev/watchdog handling
*/
-static ssize_t fop_write(struct file * file, const char __user * buf, size_t count, loff_t * ppos)
+static ssize_t fop_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count) {
+ if (count) {
if (!nowayout) {
size_t ofs;
wdt_expect_close = 0;
/* now scan */
- for(ofs = 0; ofs != count; ofs++) {
+ for (ofs = 0; ofs != count; ofs++) {
char c;
if (get_user(c, buf + ofs))
return -EFAULT;
- if(c == 'V')
+ if (c == 'V')
wdt_expect_close = 42;
}
}
- /* Well, anyhow someone wrote to us, we should return that favour */
+ /* Well, anyhow someone wrote to us, we should
+ return that favour */
wdt_keepalive();
}
return count;
}
-static int fop_open(struct inode * inode, struct file * file)
+static int fop_open(struct inode *inode, struct file *file)
{
/* Just in case we're already talking to someone... */
- if(test_and_set_bit(0, &wdt_is_open))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
if (nowayout)
__module_get(THIS_MODULE);
return nonseekable_open(inode, file);
}
-static int fop_close(struct inode * inode, struct file * file)
+static int fop_close(struct inode *inode, struct file *file)
{
- if(wdt_expect_close == 42) {
+ if (wdt_expect_close == 42)
wdt_turnoff();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
wdt_keepalive();
}
clear_bit(0, &wdt_is_open);
return 0;
}
-static int fop_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long fop_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "SC520",
};
- switch(cmd)
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
{
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if(get_user(new_options, p))
- return -EFAULT;
-
- if(new_options & WDIOS_DISABLECARD) {
- wdt_turnoff();
- retval = 0;
- }
+ int new_options, retval = -EINVAL;
- if(new_options & WDIOS_ENABLECARD) {
- wdt_startup();
- retval = 0;
- }
+ if (get_user(new_options, p))
+ return -EFAULT;
- return retval;
+ if (new_options & WDIOS_DISABLECARD) {
+ wdt_turnoff();
+ retval = 0;
}
- case WDIOC_SETTIMEOUT:
- {
- int new_timeout;
- if(get_user(new_timeout, p))
- return -EFAULT;
+ if (new_options & WDIOS_ENABLECARD) {
+ wdt_startup();
+ retval = 0;
+ }
- if(wdt_set_heartbeat(new_timeout))
- return -EINVAL;
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
- wdt_keepalive();
- /* Fall through */
- }
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+
+ if (wdt_set_heartbeat(new_timeout))
+ return -EINVAL;
+
+ wdt_keepalive();
+ /* Fall through */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
.write = fop_write,
.open = fop_open,
.release = fop_close,
- .ioctl = fop_ioctl,
+ .unlocked_ioctl = fop_ioctl,
};
static struct miscdevice wdt_miscdev = {
static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_turnoff();
return NOTIFY_DONE;
}
{
int rc = -EBUSY;
- /* Check that the timeout value is within it's range ; if not reset to the default */
+ /* Check that the timeout value is within it's range ;
+ if not reset to the default */
if (wdt_set_heartbeat(timeout)) {
wdt_set_heartbeat(WATCHDOG_TIMEOUT);
- printk(KERN_INFO PFX "timeout value must be 1<=timeout<=3600, using %d\n",
- WATCHDOG_TIMEOUT);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= timeout <= 3600, using %d\n",
+ WATCHDOG_TIMEOUT);
}
wdtmrctl = ioremap((unsigned long)(MMCR_BASE + OFFS_WDTMRCTL), 2);
rc = register_reboot_notifier(&wdt_notifier);
if (rc) {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out_ioremap;
}
rc = misc_register(&wdt_miscdev);
if (rc) {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, rc);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, rc);
goto err_out_notifier;
}
- printk(KERN_INFO PFX "WDT driver for SC520 initialised. timeout=%d sec (nowayout=%d)\n",
- timeout,nowayout);
+ printk(KERN_INFO PFX
+ "WDT driver for SC520 initialised. timeout=%d sec (nowayout=%d)\n",
+ timeout, nowayout);
return 0;
#include <linux/fs.h>
#include <linux/ioport.h>
#include <linux/scx200.h>
-
-#include <asm/uaccess.h>
-#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
#define NAME "scx200_wdt"
MODULE_PARM_DESC(nowayout, "Disable watchdog shutdown on close");
static u16 wdto_restart;
-static struct semaphore open_semaphore;
static char expect_close;
+static unsigned long open_lock;
+static DEFINE_SPINLOCK(scx_lock);
/* Bits of the WDCNFG register */
#define W_ENABLE 0x00fa /* Enable watchdog */
static void scx200_wdt_ping(void)
{
+ spin_lock(&scx_lock);
outw(wdto_restart, scx200_cb_base + SCx200_WDT_WDTO);
+ spin_unlock(&scx_lock);
}
static void scx200_wdt_update_margin(void)
printk(KERN_DEBUG NAME ": enabling watchdog timer, wdto_restart = %d\n",
wdto_restart);
+ spin_lock(&scx_lock);
outw(0, scx200_cb_base + SCx200_WDT_WDTO);
outb(SCx200_WDT_WDSTS_WDOVF, scx200_cb_base + SCx200_WDT_WDSTS);
outw(W_ENABLE, scx200_cb_base + SCx200_WDT_WDCNFG);
+ spin_unlock(&scx_lock);
scx200_wdt_ping();
}
{
printk(KERN_DEBUG NAME ": disabling watchdog timer\n");
+ spin_lock(&scx_lock);
outw(0, scx200_cb_base + SCx200_WDT_WDTO);
outb(SCx200_WDT_WDSTS_WDOVF, scx200_cb_base + SCx200_WDT_WDSTS);
outw(W_DISABLE, scx200_cb_base + SCx200_WDT_WDCNFG);
+ spin_unlock(&scx_lock);
}
static int scx200_wdt_open(struct inode *inode, struct file *file)
{
/* only allow one at a time */
- if (down_trylock(&open_semaphore))
+ if (test_and_set_bit(0, &open_lock))
return -EBUSY;
scx200_wdt_enable();
static int scx200_wdt_release(struct inode *inode, struct file *file)
{
- if (expect_close != 42) {
+ if (expect_close != 42)
printk(KERN_WARNING NAME ": watchdog device closed unexpectedly, will not disable the watchdog timer\n");
- } else if (!nowayout) {
+ else if (!nowayout)
scx200_wdt_disable();
- }
expect_close = 0;
- up(&open_semaphore);
+ clear_bit(0, &open_lock);
return 0;
}
return NOTIFY_DONE;
}
-static struct notifier_block scx200_wdt_notifier =
-{
+static struct notifier_block scx200_wdt_notifier = {
.notifier_call = scx200_wdt_notify_sys,
};
size_t len, loff_t *ppos)
{
/* check for a magic close character */
- if (len)
- {
+ if (len) {
size_t i;
scx200_wdt_ping();
expect_close = 0;
for (i = 0; i < len; ++i) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
return 0;
}
-static int scx200_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long scx200_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.identity = "NatSemi SCx200 Watchdog",
.firmware_version = 1,
- .options = (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING),
+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
};
int new_margin;
switch (cmd) {
- default:
- return -ENOTTY;
case WDIOC_GETSUPPORT:
- if(copy_to_user(argp, &ident, sizeof(ident)))
+ if (copy_to_user(argp, &ident, sizeof(ident)))
return -EFAULT;
return 0;
case WDIOC_GETSTATUS:
if (put_user(margin, p))
return -EFAULT;
return 0;
+ default:
+ return -ENOTTY;
}
}
static const struct file_operations scx200_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = scx200_wdt_write,
- .ioctl = scx200_wdt_ioctl,
- .open = scx200_wdt_open,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = scx200_wdt_write,
+ .unlocked_ioctl = scx200_wdt_ioctl,
+ .open = scx200_wdt_open,
.release = scx200_wdt_release,
};
static struct miscdevice scx200_wdt_miscdev = {
.minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &scx200_wdt_fops,
+ .name = "watchdog",
+ .fops = &scx200_wdt_fops,
};
static int __init scx200_wdt_init(void)
scx200_wdt_update_margin();
scx200_wdt_disable();
- sema_init(&open_semaphore, 1);
-
r = register_reboot_notifier(&scx200_wdt_notifier);
if (r) {
printk(KERN_ERR NAME ": unable to register reboot notifier");
/*
Local variables:
- compile-command: "make -k -C ../.. SUBDIRS=drivers/char modules"
- c-basic-offset: 8
+ compile-command: "make -k -C ../.. SUBDIRS=drivers/char modules"
+ c-basic-offset: 8
End:
*/
#include <linux/ioport.h>
#include <linux/fs.h>
#include <linux/mm.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/watchdog.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
+#include <linux/watchdog.h>
#define PFX "shwdt: "
static char shwdt_expect_close;
static DEFINE_TIMER(timer, sh_wdt_ping, 0, 0);
static unsigned long next_heartbeat;
+static DEFINE_SPINLOCK(shwdt_lock);
#define WATCHDOG_HEARTBEAT 30 /* 30 sec default heartbeat */
static int heartbeat = WATCHDOG_HEARTBEAT; /* in seconds */
static void sh_wdt_start(void)
{
__u8 csr;
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt_lock, flags);
next_heartbeat = jiffies + (heartbeat * HZ);
mod_timer(&timer, next_ping_period(clock_division_ratio));
csr &= ~RSTCSR_RSTS;
sh_wdt_write_rstcsr(csr);
#endif
+ spin_unlock_irqrestore(&wdt_lock, flags);
}
/**
static void sh_wdt_stop(void)
{
__u8 csr;
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt_lock, flags);
del_timer(&timer);
csr = sh_wdt_read_csr();
csr &= ~WTCSR_TME;
sh_wdt_write_csr(csr);
+ spin_unlock_irqrestore(&wdt_lock, flags);
}
/**
*/
static inline void sh_wdt_keepalive(void)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt_lock, flags);
next_heartbeat = jiffies + (heartbeat * HZ);
+ spin_unlock_irqrestore(&wdt_lock, flags);
}
/**
*/
static int sh_wdt_set_heartbeat(int t)
{
- if (unlikely((t < 1) || (t > 3600))) /* arbitrary upper limit */
+ unsigned long flags;
+
+ if (unlikely(t < 1 || t > 3600)) /* arbitrary upper limit */
return -EINVAL;
+ spin_lock_irqsave(&wdt_lock, flags);
heartbeat = t;
+ spin_unlock_irqrestore(&wdt_lock, flags);
return 0;
}
*/
static void sh_wdt_ping(unsigned long data)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt_lock, flags);
if (time_before(jiffies, next_heartbeat)) {
__u8 csr;
} else
printk(KERN_WARNING PFX "Heartbeat lost! Will not ping "
"the watchdog\n");
+ spin_unlock_irqrestore(&wdt_lock, flags);
}
/**
/**
* sh_wdt_ioctl - Query Device
- * @inode: inode of device
* @file: file handle of device
* @cmd: watchdog command
* @arg: argument
* Query basic information from the device or ping it, as outlined by the
* watchdog API.
*/
-static int sh_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long sh_wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_heartbeat;
int options, retval = -EINVAL;
switch (cmd) {
- case WDIOC_GETSUPPORT:
- return copy_to_user((struct watchdog_info *)arg,
- &sh_wdt_info,
- sizeof(sh_wdt_info)) ? -EFAULT : 0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, (int *)arg);
- case WDIOC_KEEPALIVE:
- sh_wdt_keepalive();
- return 0;
- case WDIOC_SETTIMEOUT:
- if (get_user(new_heartbeat, (int *)arg))
- return -EFAULT;
-
- if (sh_wdt_set_heartbeat(new_heartbeat))
- return -EINVAL;
-
- sh_wdt_keepalive();
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, (int *)arg);
- case WDIOC_SETOPTIONS:
- if (get_user(options, (int *)arg))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- sh_wdt_stop();
- retval = 0;
- }
+ case WDIOC_GETSUPPORT:
+ return copy_to_user((struct watchdog_info *)arg,
+ &sh_wdt_info, sizeof(sh_wdt_info)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, (int *)arg);
+ case WDIOC_SETOPTIONS:
+ if (get_user(options, (int *)arg))
+ return -EFAULT;
+
+ if (options & WDIOS_DISABLECARD) {
+ sh_wdt_stop();
+ retval = 0;
+ }
- if (options & WDIOS_ENABLECARD) {
- sh_wdt_start();
- retval = 0;
- }
+ if (options & WDIOS_ENABLECARD) {
+ sh_wdt_start();
+ retval = 0;
+ }
- return retval;
- default:
- return -ENOTTY;
- }
+ return retval;
+ case WDIOC_KEEPALIVE:
+ sh_wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_heartbeat, (int *)arg))
+ return -EFAULT;
+
+ if (sh_wdt_set_heartbeat(new_heartbeat))
+ return -EINVAL;
+ sh_wdt_keepalive();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, (int *)arg);
+ default:
+ return -ENOTTY;
+ }
return 0;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = sh_wdt_write,
- .ioctl = sh_wdt_ioctl,
+ .unlocked_ioctl = sh_wdt_ioctl,
.open = sh_wdt_open,
.release = sh_wdt_close,
.mmap = sh_wdt_mmap,
};
-static struct watchdog_info sh_wdt_info = {
+static const struct watchdog_info sh_wdt_info = {
.options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
WDIOF_MAGICCLOSE,
.firmware_version = 1,
{
int rc;
- if ((clock_division_ratio < 0x5) || (clock_division_ratio > 0x7)) {
+ if (clock_division_ratio < 0x5 || clock_division_ratio > 0x7) {
clock_division_ratio = WTCSR_CKS_4096;
- printk(KERN_INFO PFX "clock_division_ratio value must "
- "be 0x5<=x<=0x7, using %d\n", clock_division_ratio);
+ printk(KERN_INFO PFX
+ "clock_division_ratio value must be 0x5<=x<=0x7, using %d\n",
+ clock_division_ratio);
}
rc = sh_wdt_set_heartbeat(heartbeat);
if (unlikely(rc)) {
heartbeat = WATCHDOG_HEARTBEAT;
- printk(KERN_INFO PFX "heartbeat value must "
- "be 1<=x<=3600, using %d\n", heartbeat);
+ printk(KERN_INFO PFX
+ "heartbeat value must be 1<=x<=3600, using %d\n",
+ heartbeat);
}
rc = register_reboot_notifier(&sh_wdt_notifier);
if (unlikely(rc)) {
- printk(KERN_ERR PFX "Can't register reboot notifier (err=%d)\n",
- rc);
+ printk(KERN_ERR PFX
+ "Can't register reboot notifier (err=%d)\n", rc);
return rc;
}
rc = misc_register(&sh_wdt_miscdev);
if (unlikely(rc)) {
- printk(KERN_ERR PFX "Can't register miscdev on "
- "minor=%d (err=%d)\n", sh_wdt_miscdev.minor, rc);
+ printk(KERN_ERR PFX
+ "Can't register miscdev on minor=%d (err=%d)\n",
+ sh_wdt_miscdev.minor, rc);
unregister_reboot_notifier(&sh_wdt_notifier);
return rc;
}
MODULE_PARM_DESC(clock_division_ratio, "Clock division ratio. Valid ranges are from 0x5 (1.31ms) to 0x7 (5.25ms). (default=" __MODULE_STRING(clock_division_ratio) ")");
module_param(heartbeat, int, 0);
-MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (1<=heartbeat<=3600, default=" __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
+MODULE_PARM_DESC(heartbeat,
+ "Watchdog heartbeat in seconds. (1 <= heartbeat <= 3600, default="
+ __MODULE_STRING(WATCHDOG_HEARTBEAT) ")");
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
module_init(sh_wdt_init);
module_exit(sh_wdt_exit);
* History:
* 2003 - Created version 1.0 for Linux 2.4.x.
* 2006 - Ported to Linux 2.6, added nowayout and MAGICCLOSE
- * features. Released version 1.1
+ * features. Released version 1.1
*
* Theory of operation:
*
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
/* enable support for minutes as units? */
#define UNIT_MINUTE 1
#define MODNAME "smsc37b787_wdt: "
-#define VERSION "1.1"
+#define VERSION "1.1"
-#define IOPORT 0x3F0
+#define IOPORT 0x3F0
#define IOPORT_SIZE 2
-#define IODEV_NO 8
+#define IODEV_NO 8
-static int unit = UNIT_SECOND; /* timer's unit */
-static int timeout = 60; /* timeout value: default is 60 "units" */
-static unsigned long timer_enabled = 0; /* is the timer enabled? */
+static int unit = UNIT_SECOND; /* timer's unit */
+static int timeout = 60; /* timeout value: default is 60 "units" */
+static unsigned long timer_enabled; /* is the timer enabled? */
static char expect_close; /* is the close expected? */
static inline void open_io_config(void)
{
- outb(0x55, IOPORT);
+ outb(0x55, IOPORT);
mdelay(1);
- outb(0x55, IOPORT);
+ outb(0x55, IOPORT);
}
/* lock the IO chip */
static inline void close_io_config(void)
{
- outb(0xAA, IOPORT);
+ outb(0xAA, IOPORT);
}
/* select the IO device */
static inline void select_io_device(unsigned char devno)
{
- outb(0x07, IOPORT);
- outb(devno, IOPORT+1);
+ outb(0x07, IOPORT);
+ outb(devno, IOPORT+1);
}
/* write to the control register */
static inline void write_io_cr(unsigned char reg, unsigned char data)
{
- outb(reg, IOPORT);
- outb(data, IOPORT+1);
+ outb(reg, IOPORT);
+ outb(data, IOPORT+1);
}
/* read from the control register */
static inline char read_io_cr(unsigned char reg)
{
- outb(reg, IOPORT);
- return inb(IOPORT+1);
+ outb(reg, IOPORT);
+ return inb(IOPORT+1);
}
/* -- Medium level functions ------------------------------------*/
static inline void gpio_bit12(unsigned char reg)
{
- // -- General Purpose I/O Bit 1.2 --
- // Bit 0, In/Out: 0 = Output, 1 = Input
- // Bit 1, Polarity: 0 = No Invert, 1 = Invert
- // Bit 2, Group Enable Intr.: 0 = Disable, 1 = Enable
- // Bit 3/4, Function select: 00 = GPI/O, 01 = WDT, 10 = P17,
- // 11 = Either Edge Triggered Intr. 2
- // Bit 5/6 (Reserved)
- // Bit 7, Output Type: 0 = Push Pull Bit, 1 = Open Drain
- write_io_cr(0xE2, reg);
+ /* -- General Purpose I/O Bit 1.2 --
+ * Bit 0, In/Out: 0 = Output, 1 = Input
+ * Bit 1, Polarity: 0 = No Invert, 1 = Invert
+ * Bit 2, Group Enable Intr.: 0 = Disable, 1 = Enable
+ * Bit 3/4, Function select: 00 = GPI/O, 01 = WDT, 10 = P17,
+ * 11 = Either Edge Triggered Intr. 2
+ * Bit 5/6 (Reserved)
+ * Bit 7, Output Type: 0 = Push Pull Bit, 1 = Open Drain
+ */
+ write_io_cr(0xE2, reg);
}
static inline void gpio_bit13(unsigned char reg)
{
- // -- General Purpose I/O Bit 1.3 --
- // Bit 0, In/Out: 0 = Output, 1 = Input
- // Bit 1, Polarity: 0 = No Invert, 1 = Invert
- // Bit 2, Group Enable Intr.: 0 = Disable, 1 = Enable
- // Bit 3, Function select: 0 = GPI/O, 1 = LED
- // Bit 4-6 (Reserved)
- // Bit 7, Output Type: 0 = Push Pull Bit, 1 = Open Drain
- write_io_cr(0xE3, reg);
+ /* -- General Purpose I/O Bit 1.3 --
+ * Bit 0, In/Out: 0 = Output, 1 = Input
+ * Bit 1, Polarity: 0 = No Invert, 1 = Invert
+ * Bit 2, Group Enable Intr.: 0 = Disable, 1 = Enable
+ * Bit 3, Function select: 0 = GPI/O, 1 = LED
+ * Bit 4-6 (Reserved)
+ * Bit 7, Output Type: 0 = Push Pull Bit, 1 = Open Drain
+ */
+ write_io_cr(0xE3, reg);
}
static inline void wdt_timer_units(unsigned char new_units)
{
- // -- Watchdog timer units --
- // Bit 0-6 (Reserved)
- // Bit 7, WDT Time-out Value Units Select
- // (0 = Minutes, 1 = Seconds)
- write_io_cr(0xF1, new_units);
+ /* -- Watchdog timer units --
+ * Bit 0-6 (Reserved)
+ * Bit 7, WDT Time-out Value Units Select
+ * (0 = Minutes, 1 = Seconds)
+ */
+ write_io_cr(0xF1, new_units);
}
static inline void wdt_timeout_value(unsigned char new_timeout)
{
- // -- Watchdog Timer Time-out Value --
- // Bit 0-7 Binary coded units (0=Disabled, 1..255)
- write_io_cr(0xF2, new_timeout);
+ /* -- Watchdog Timer Time-out Value --
+ * Bit 0-7 Binary coded units (0=Disabled, 1..255)
+ */
+ write_io_cr(0xF2, new_timeout);
}
static inline void wdt_timer_conf(unsigned char conf)
{
- // -- Watchdog timer configuration --
- // Bit 0 Joystick enable: 0* = No Reset, 1 = Reset WDT upon Gameport I/O
- // Bit 1 Keyboard enable: 0* = No Reset, 1 = Reset WDT upon KBD Intr.
- // Bit 2 Mouse enable: 0* = No Reset, 1 = Reset WDT upon Mouse Intr.
- // Bit 3 Reset the timer
- // (Wrong in SMsC documentation? Given as: PowerLED Timout Enabled)
- // Bit 4-7 WDT Interrupt Mapping: (0000* = Disabled,
- // 0001=IRQ1, 0010=(Invalid), 0011=IRQ3 to 1111=IRQ15)
- write_io_cr(0xF3, conf);
+ /* -- Watchdog timer configuration --
+ * Bit 0 Joystick enable: 0* = No Reset, 1 = Reset WDT upon
+ * Gameport I/O
+ * Bit 1 Keyboard enable: 0* = No Reset, 1 = Reset WDT upon KBD Intr.
+ * Bit 2 Mouse enable: 0* = No Reset, 1 = Reset WDT upon Mouse Intr
+ * Bit 3 Reset the timer
+ * (Wrong in SMsC documentation? Given as: PowerLED Timout
+ * Enabled)
+ * Bit 4-7 WDT Interrupt Mapping: (0000* = Disabled,
+ * 0001=IRQ1, 0010=(Invalid), 0011=IRQ3 to 1111=IRQ15)
+ */
+ write_io_cr(0xF3, conf);
}
static inline void wdt_timer_ctrl(unsigned char reg)
{
- // -- Watchdog timer control --
- // Bit 0 Status Bit: 0 = Timer counting, 1 = Timeout occured
- // Bit 1 Power LED Toggle: 0 = Disable Toggle, 1 = Toggle at 1 Hz
- // Bit 2 Force Timeout: 1 = Forces WD timeout event (self-cleaning)
- // Bit 3 P20 Force Timeout enabled:
- // 0 = P20 activity does not generate the WD timeout event
- // 1 = P20 Allows rising edge of P20, from the keyboard
- // controller, to force the WD timeout event.
- // Bit 4 (Reserved)
- // -- Soft power management --
- // Bit 5 Stop Counter: 1 = Stop software power down counter
- // set via register 0xB8, (self-cleaning)
- // (Upon read: 0 = Counter running, 1 = Counter stopped)
- // Bit 6 Restart Counter: 1 = Restart software power down counter
- // set via register 0xB8, (self-cleaning)
- // Bit 7 SPOFF: 1 = Force software power down (self-cleaning)
-
- write_io_cr(0xF4, reg);
+ /* -- Watchdog timer control --
+ * Bit 0 Status Bit: 0 = Timer counting, 1 = Timeout occured
+ * Bit 1 Power LED Toggle: 0 = Disable Toggle, 1 = Toggle at 1 Hz
+ * Bit 2 Force Timeout: 1 = Forces WD timeout event (self-cleaning)
+ * Bit 3 P20 Force Timeout enabled:
+ * 0 = P20 activity does not generate the WD timeout event
+ * 1 = P20 Allows rising edge of P20, from the keyboard
+ * controller, to force the WD timeout event.
+ * Bit 4 (Reserved)
+ * -- Soft power management --
+ * Bit 5 Stop Counter: 1 = Stop software power down counter
+ * set via register 0xB8, (self-cleaning)
+ * (Upon read: 0 = Counter running, 1 = Counter stopped)
+ * Bit 6 Restart Counter: 1 = Restart software power down counter
+ * set via register 0xB8, (self-cleaning)
+ * Bit 7 SPOFF: 1 = Force software power down (self-cleaning)
+ */
+ write_io_cr(0xF4, reg);
}
/* -- Higher level functions ------------------------------------*/
static void wb_smsc_wdt_initialize(void)
{
- unsigned char old;
+ unsigned char old;
spin_lock(&io_lock);
- open_io_config();
- select_io_device(IODEV_NO);
+ open_io_config();
+ select_io_device(IODEV_NO);
- // enable the watchdog
- gpio_bit13(0x08); // Select pin 80 = LED not GPIO
- gpio_bit12(0x0A); // Set pin 79 = WDT not GPIO/Output/Polarity=Invert
+ /* enable the watchdog */
+ gpio_bit13(0x08); /* Select pin 80 = LED not GPIO */
+ gpio_bit12(0x0A); /* Set pin 79 = WDT not
+ GPIO/Output/Polarity=Invert */
+ /* disable the timeout */
+ wdt_timeout_value(0);
- // disable the timeout
- wdt_timeout_value(0);
+ /* reset control register */
+ wdt_timer_ctrl(0x00);
- // reset control register
- wdt_timer_ctrl(0x00);
-
- // reset configuration register
+ /* reset configuration register */
wdt_timer_conf(0x00);
- // read old (timer units) register
- old = read_io_cr(0xF1) & 0x7F;
- if (unit == UNIT_SECOND) old |= 0x80; // set to seconds
+ /* read old (timer units) register */
+ old = read_io_cr(0xF1) & 0x7F;
+ if (unit == UNIT_SECOND)
+ old |= 0x80; /* set to seconds */
- // set the watchdog timer units
- wdt_timer_units(old);
+ /* set the watchdog timer units */
+ wdt_timer_units(old);
- close_io_config();
+ close_io_config();
spin_unlock(&io_lock);
}
static void wb_smsc_wdt_shutdown(void)
{
spin_lock(&io_lock);
- open_io_config();
- select_io_device(IODEV_NO);
+ open_io_config();
+ select_io_device(IODEV_NO);
- // disable the watchdog
- gpio_bit13(0x09);
- gpio_bit12(0x09);
+ /* disable the watchdog */
+ gpio_bit13(0x09);
+ gpio_bit12(0x09);
- // reset watchdog config register
+ /* reset watchdog config register */
wdt_timer_conf(0x00);
- // reset watchdog control register
- wdt_timer_ctrl(0x00);
+ /* reset watchdog control register */
+ wdt_timer_ctrl(0x00);
- // disable timeout
- wdt_timeout_value(0x00);
+ /* disable timeout */
+ wdt_timeout_value(0x00);
- close_io_config();
+ close_io_config();
spin_unlock(&io_lock);
}
static void wb_smsc_wdt_set_timeout(unsigned char new_timeout)
{
spin_lock(&io_lock);
- open_io_config();
- select_io_device(IODEV_NO);
+ open_io_config();
+ select_io_device(IODEV_NO);
- // set Power LED to blink, if we enable the timeout
- wdt_timer_ctrl((new_timeout == 0) ? 0x00 : 0x02);
+ /* set Power LED to blink, if we enable the timeout */
+ wdt_timer_ctrl((new_timeout == 0) ? 0x00 : 0x02);
- // set timeout value
- wdt_timeout_value(new_timeout);
+ /* set timeout value */
+ wdt_timeout_value(new_timeout);
- close_io_config();
+ close_io_config();
spin_unlock(&io_lock);
}
static unsigned char wb_smsc_wdt_get_timeout(void)
{
- unsigned char set_timeout;
+ unsigned char set_timeout;
spin_lock(&io_lock);
- open_io_config();
- select_io_device(IODEV_NO);
- set_timeout = read_io_cr(0xF2);
- close_io_config();
+ open_io_config();
+ select_io_device(IODEV_NO);
+ set_timeout = read_io_cr(0xF2);
+ close_io_config();
spin_unlock(&io_lock);
- return set_timeout;
+ return set_timeout;
}
/* disable watchdog */
static void wb_smsc_wdt_disable(void)
{
- // set the timeout to 0 to disable the watchdog
- wb_smsc_wdt_set_timeout(0);
+ /* set the timeout to 0 to disable the watchdog */
+ wb_smsc_wdt_set_timeout(0);
}
/* enable watchdog by setting the current timeout */
static void wb_smsc_wdt_enable(void)
{
- // set the current timeout...
- wb_smsc_wdt_set_timeout(timeout);
+ /* set the current timeout... */
+ wb_smsc_wdt_set_timeout(timeout);
}
/* reset the timer */
static void wb_smsc_wdt_reset_timer(void)
{
spin_lock(&io_lock);
- open_io_config();
- select_io_device(IODEV_NO);
+ open_io_config();
+ select_io_device(IODEV_NO);
- // reset the timer
+ /* reset the timer */
wdt_timeout_value(timeout);
wdt_timer_conf(0x08);
- close_io_config();
+ close_io_config();
spin_unlock(&io_lock);
}
/* Reload and activate timer */
wb_smsc_wdt_enable();
- printk(KERN_INFO MODNAME "Watchdog enabled. Timeout set to %d %s.\n", timeout, (unit == UNIT_SECOND) ? "second(s)" : "minute(s)");
+ printk(KERN_INFO MODNAME
+ "Watchdog enabled. Timeout set to %d %s.\n",
+ timeout, (unit == UNIT_SECOND) ? "second(s)" : "minute(s)");
return nonseekable_open(inode, file);
}
/* Shut off the timer. */
if (expect_close == 42) {
- wb_smsc_wdt_disable();
- printk(KERN_INFO MODNAME "Watchdog disabled, sleeping again...\n");
+ wb_smsc_wdt_disable();
+ printk(KERN_INFO MODNAME
+ "Watchdog disabled, sleeping again...\n");
} else {
- printk(KERN_CRIT MODNAME "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT MODNAME
+ "Unexpected close, not stopping watchdog!\n");
wb_smsc_wdt_reset_timer();
}
/* reset expect flag */
expect_close = 0;
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got the
+ magic character */
for (i = 0; i != len; i++) {
char c;
- if (get_user(c, data+i))
+ if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
/* ioctl => control interface */
-static int wb_smsc_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long wb_smsc_wdt_ioctl(struct file *file,
+ unsigned int cmd, unsigned long arg)
{
int new_timeout;
int __user *i;
} uarg;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.options = WDIOF_KEEPALIVEPING |
- WDIOF_SETTIMEOUT |
+ WDIOF_SETTIMEOUT |
WDIOF_MAGICCLOSE,
.firmware_version = 0,
- .identity = "SMsC 37B787 Watchdog"
+ .identity = "SMsC 37B787 Watchdog",
};
uarg.i = (int __user *)arg;
switch (cmd) {
- default:
- return -ENOTTY;
-
- case WDIOC_GETSUPPORT:
- return copy_to_user(uarg.ident, &ident,
- sizeof(ident)) ? -EFAULT : 0;
-
- case WDIOC_GETSTATUS:
- return put_user(wb_smsc_wdt_status(), uarg.i);
-
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, uarg.i);
-
- case WDIOC_KEEPALIVE:
- wb_smsc_wdt_reset_timer();
- return 0;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, uarg.i))
- return -EFAULT;
-
- // the API states this is given in secs
- if (unit == UNIT_MINUTE)
- new_timeout /= 60;
-
- if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
- return -EINVAL;
-
- timeout = new_timeout;
- wb_smsc_wdt_set_timeout(timeout);
-
- // fall through and return the new timeout...
-
- case WDIOC_GETTIMEOUT:
-
- new_timeout = timeout;
-
- if (unit == UNIT_MINUTE)
- new_timeout *= 60;
-
- return put_user(new_timeout, uarg.i);
-
- case WDIOC_SETOPTIONS:
- {
- int options, retval = -EINVAL;
-
- if (get_user(options, uarg.i))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- wb_smsc_wdt_disable();
- retval = 0;
- }
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(uarg.ident, &ident, sizeof(ident))
+ ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ return put_user(wb_smsc_wdt_status(), uarg.i);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, uarg.i);
+ case WDIOC_SETOPTIONS:
+ {
+ int options, retval = -EINVAL;
- if (options & WDIOS_ENABLECARD) {
- wb_smsc_wdt_enable();
- retval = 0;
- }
+ if (get_user(options, uarg.i))
+ return -EFAULT;
- return retval;
+ if (options & WDIOS_DISABLECARD) {
+ wb_smsc_wdt_disable();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ wb_smsc_wdt_enable();
+ retval = 0;
}
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wb_smsc_wdt_reset_timer();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, uarg.i))
+ return -EFAULT;
+ /* the API states this is given in secs */
+ if (unit == UNIT_MINUTE)
+ new_timeout /= 60;
+ if (new_timeout < 0 || new_timeout > MAX_TIMEOUT)
+ return -EINVAL;
+ timeout = new_timeout;
+ wb_smsc_wdt_set_timeout(timeout);
+ /* fall through and return the new timeout... */
+ case WDIOC_GETTIMEOUT:
+ new_timeout = timeout;
+ if (unit == UNIT_MINUTE)
+ new_timeout *= 60;
+ return put_user(new_timeout, uarg.i);
+ default:
+ return -ENOTTY;
}
}
/* -- Notifier funtions -----------------------------------------*/
-static int wb_smsc_wdt_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int wb_smsc_wdt_notify_sys(struct notifier_block *this,
+ unsigned long code, void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT)
- {
- // set timeout to 0, to avoid possible race-condition
- timeout = 0;
+ if (code == SYS_DOWN || code == SYS_HALT) {
+ /* set timeout to 0, to avoid possible race-condition */
+ timeout = 0;
wb_smsc_wdt_disable();
}
return NOTIFY_DONE;
/* -- Module's structures ---------------------------------------*/
-static const struct file_operations wb_smsc_wdt_fops =
-{
- .owner = THIS_MODULE,
+static const struct file_operations wb_smsc_wdt_fops = {
+ .owner = THIS_MODULE,
.llseek = no_llseek,
.write = wb_smsc_wdt_write,
- .ioctl = wb_smsc_wdt_ioctl,
+ .unlocked_ioctl = wb_smsc_wdt_ioctl,
.open = wb_smsc_wdt_open,
.release = wb_smsc_wdt_release,
};
-static struct notifier_block wb_smsc_wdt_notifier =
-{
+static struct notifier_block wb_smsc_wdt_notifier = {
.notifier_call = wb_smsc_wdt_notify_sys,
};
-static struct miscdevice wb_smsc_wdt_miscdev =
-{
+static struct miscdevice wb_smsc_wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &wb_smsc_wdt_fops,
{
int ret;
- printk("SMsC 37B787 watchdog component driver " VERSION " initialising...\n");
+ printk(KERN_INFO "SMsC 37B787 watchdog component driver "
+ VERSION " initialising...\n");
if (!request_region(IOPORT, IOPORT_SIZE, "SMsC 37B787 watchdog")) {
- printk(KERN_ERR MODNAME "Unable to register IO port %#x\n", IOPORT);
+ printk(KERN_ERR MODNAME "Unable to register IO port %#x\n",
+ IOPORT);
ret = -EBUSY;
goto out_pnp;
}
- // set new maximum, if it's too big
- if (timeout > MAX_TIMEOUT)
- timeout = MAX_TIMEOUT;
+ /* set new maximum, if it's too big */
+ if (timeout > MAX_TIMEOUT)
+ timeout = MAX_TIMEOUT;
- // init the watchdog timer
- wb_smsc_wdt_initialize();
+ /* init the watchdog timer */
+ wb_smsc_wdt_initialize();
ret = register_reboot_notifier(&wb_smsc_wdt_notifier);
if (ret) {
- printk(KERN_ERR MODNAME "Unable to register reboot notifier err = %d\n", ret);
+ printk(KERN_ERR MODNAME
+ "Unable to register reboot notifier err = %d\n", ret);
goto out_io;
}
ret = misc_register(&wb_smsc_wdt_miscdev);
if (ret) {
- printk(KERN_ERR MODNAME "Unable to register miscdev on minor %d\n", WATCHDOG_MINOR);
+ printk(KERN_ERR MODNAME
+ "Unable to register miscdev on minor %d\n",
+ WATCHDOG_MINOR);
goto out_rbt;
}
- // output info
- printk(KERN_INFO MODNAME "Timeout set to %d %s.\n", timeout, (unit == UNIT_SECOND) ? "second(s)" : "minute(s)");
- printk(KERN_INFO MODNAME "Watchdog initialized and sleeping (nowayout=%d)...\n", nowayout);
-
- // ret = 0
-
+ /* output info */
+ printk(KERN_INFO MODNAME "Timeout set to %d %s.\n",
+ timeout, (unit == UNIT_SECOND) ? "second(s)" : "minute(s)");
+ printk(KERN_INFO MODNAME
+ "Watchdog initialized and sleeping (nowayout=%d)...\n",
+ nowayout);
out_clean:
return ret;
static void __exit wb_smsc_wdt_exit(void)
{
/* Stop the timer before we leave */
- if (!nowayout)
- {
+ if (!nowayout) {
wb_smsc_wdt_shutdown();
printk(KERN_INFO MODNAME "Watchdog disabled.\n");
}
unregister_reboot_notifier(&wb_smsc_wdt_notifier);
release_region(IOPORT, IOPORT_SIZE);
- printk("SMsC 37B787 watchdog component driver removed.\n");
+ printk(KERN_INFO "SMsC 37B787 watchdog component driver removed.\n");
}
module_init(wb_smsc_wdt_init);
module_exit(wb_smsc_wdt_exit);
MODULE_AUTHOR("Sven Anders <anders@anduras.de>");
-MODULE_DESCRIPTION("Driver for SMsC 37B787 watchdog component (Version " VERSION ")");
+MODULE_DESCRIPTION("Driver for SMsC 37B787 watchdog component (Version "
+ VERSION ")");
MODULE_LICENSE("GPL");
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
#ifdef SMSC_SUPPORT_MINUTES
module_param(unit, int, 0);
-MODULE_PARM_DESC(unit, "set unit to use, 0=seconds or 1=minutes, default is 0");
+MODULE_PARM_DESC(unit,
+ "set unit to use, 0=seconds or 1=minutes, default is 0");
#endif
module_param(timeout, int, 0);
MODULE_PARM_DESC(timeout, "range is 1-255 units, default is 60");
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/jiffies.h>
-
-#include <asm/uaccess.h>
+#include <linux/uaccess.h>
#define PFX "SoftDog: "
#define TIMER_MARGIN 60 /* Default is 60 seconds */
static int soft_margin = TIMER_MARGIN; /* in seconds */
module_param(soft_margin, int, 0);
-MODULE_PARM_DESC(soft_margin, "Watchdog soft_margin in seconds. (0<soft_margin<65536, default=" __MODULE_STRING(TIMER_MARGIN) ")");
+MODULE_PARM_DESC(soft_margin,
+ "Watchdog soft_margin in seconds. (0 < soft_margin < 65536, default="
+ __MODULE_STRING(TIMER_MARGIN) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#ifdef ONLY_TESTING
static int soft_noboot = 1;
if (soft_noboot)
printk(KERN_CRIT PFX "Triggered - Reboot ignored.\n");
- else
- {
+ else {
printk(KERN_CRIT PFX "Initiating system reboot.\n");
emergency_restart();
printk(KERN_CRIT PFX "Reboot didn't ?????\n");
softdog_stop();
module_put(THIS_MODULE);
} else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
set_bit(0, &orphan_timer);
softdog_keepalive();
}
return 0;
}
-static ssize_t softdog_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
+static ssize_t softdog_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
{
/*
* Refresh the timer.
*/
- if(len) {
+ if (len) {
if (!nowayout) {
size_t i;
return len;
}
-static int softdog_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long softdog_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_margin;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.options = WDIOF_SETTIMEOUT |
WDIOF_KEEPALIVEPING |
WDIOF_MAGICCLOSE,
.identity = "Software Watchdog",
};
switch (cmd) {
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident,
- sizeof(ident)) ? -EFAULT : 0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- softdog_keepalive();
- return 0;
- case WDIOC_SETTIMEOUT:
- if (get_user(new_margin, p))
- return -EFAULT;
- if (softdog_set_heartbeat(new_margin))
- return -EINVAL;
- softdog_keepalive();
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(soft_margin, p);
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ softdog_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_margin, p))
+ return -EFAULT;
+ if (softdog_set_heartbeat(new_margin))
+ return -EINVAL;
+ softdog_keepalive();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(soft_margin, p);
+ default:
+ return -ENOTTY;
}
}
static int softdog_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT) {
+ if (code == SYS_DOWN || code == SYS_HALT)
/* Turn the WDT off */
softdog_stop();
- }
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = softdog_write,
- .ioctl = softdog_ioctl,
+ .unlocked_ioctl = softdog_ioctl,
.open = softdog_open,
.release = softdog_release,
};
{
int ret;
- /* Check that the soft_margin value is within it's range ; if not reset to the default */
+ /* Check that the soft_margin value is within it's range;
+ if not reset to the default */
if (softdog_set_heartbeat(soft_margin)) {
softdog_set_heartbeat(TIMER_MARGIN);
- printk(KERN_INFO PFX "soft_margin value must be 0<soft_margin<65536, using %d\n",
+ printk(KERN_INFO PFX
+ "soft_margin must be 0 < soft_margin < 65536, using %d\n",
TIMER_MARGIN);
}
ret = register_reboot_notifier(&softdog_notifier);
if (ret) {
- printk (KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
return ret;
}
ret = misc_register(&softdog_miscdev);
if (ret) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
unregister_reboot_notifier(&softdog_notifier);
return ret;
}
static int expect_close;
static struct txx9_tmr_reg __iomem *txx9wdt_reg;
static struct clk *txx9_imclk;
+static DECLARE_LOCK(txx9_lock);
static void txx9wdt_ping(void)
{
+ spin_lock(&txx9_lock);
__raw_writel(TXx9_TMWTMR_TWIE | TXx9_TMWTMR_TWC, &txx9wdt_reg->wtmr);
+ spin_unlock(&txx9_lock);
}
static void txx9wdt_start(void)
{
+ spin_lock(&txx9_lock);
__raw_writel(WD_TIMER_CLK * timeout, &txx9wdt_reg->cpra);
__raw_writel(WD_TIMER_CCD, &txx9wdt_reg->ccdr);
__raw_writel(0, &txx9wdt_reg->tisr); /* clear pending interrupt */
__raw_writel(TXx9_TMTCR_TCE | TXx9_TMTCR_CCDE | TXx9_TMTCR_TMODE_WDOG,
&txx9wdt_reg->tcr);
__raw_writel(TXx9_TMWTMR_TWIE | TXx9_TMWTMR_TWC, &txx9wdt_reg->wtmr);
+ spin_unlock(&txx9_lock);
}
static void txx9wdt_stop(void)
{
+ spin_lock(&txx9_lock);
__raw_writel(TXx9_TMWTMR_WDIS, &txx9wdt_reg->wtmr);
__raw_writel(__raw_readl(&txx9wdt_reg->tcr) & ~TXx9_TMTCR_TCE,
&txx9wdt_reg->tcr);
+ spin_unlock(&txx9_lock);
}
static int txx9wdt_open(struct inode *inode, struct file *file)
return len;
}
-static int txx9wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long txx9wdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_timeout;
- static struct watchdog_info ident = {
+ static const struct watchdog_info ident = {
.options = WDIOF_SETTIMEOUT |
WDIOF_KEEPALIVEPING |
WDIOF_MAGICCLOSE,
};
switch (cmd) {
- default:
- return -ENOTTY;
case WDIOC_GETSUPPORT:
return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETSTATUS:
/* Fall */
case WDIOC_GETTIMEOUT:
return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
}
static const struct file_operations txx9wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = txx9wdt_write,
- .ioctl = txx9wdt_ioctl,
- .open = txx9wdt_open,
- .release = txx9wdt_release,
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .write = txx9wdt_write,
+ .unlocked_ioctl = txx9wdt_ioctl,
+ .open = txx9wdt_open,
+ .release = txx9wdt_release,
};
static struct miscdevice txx9wdt_miscdev = {
- .minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &txx9wdt_fops,
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &txx9wdt_fops,
};
static struct notifier_block txx9wdt_notifier = {
- .notifier_call = txx9wdt_notify_sys
+ .notifier_call = txx9wdt_notify_sys,
};
static int __init txx9wdt_probe(struct platform_device *dev)
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define WATCHDOG_NAME "w83627hf/thf/hg WDT"
static int timeout = WATCHDOG_TIMEOUT; /* in seconds */
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. 1<= timeout <=255, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ".");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. 1 <= timeout <= 255, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ".");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Kernel methods.
*/
#define WDT_EFER (wdt_io+0) /* Extended Function Enable Registers */
-#define WDT_EFIR (wdt_io+0) /* Extended Function Index Register (same as EFER) */
+#define WDT_EFIR (wdt_io+0) /* Extended Function Index Register
+ (same as EFER) */
#define WDT_EFDR (WDT_EFIR+1) /* Extended Function Data Register */
-static void
-w83627hf_select_wd_register(void)
+static void w83627hf_select_wd_register(void)
{
unsigned char c;
outb_p(0x87, WDT_EFER); /* Enter extended function mode */
outb_p(0x01, WDT_EFDR); /* set bit 0 to activate GPIO2 */
}
-static void
-w83627hf_unselect_wd_register(void)
+static void w83627hf_unselect_wd_register(void)
{
outb_p(0xAA, WDT_EFER); /* Leave extended function mode */
}
/* tyan motherboards seem to set F5 to 0x4C ?
* So explicitly init to appropriate value. */
-static void
-w83627hf_init(void)
+
+static void w83627hf_init(void)
{
unsigned char t;
w83627hf_select_wd_register();
outb_p(0xF6, WDT_EFER); /* Select CRF6 */
- t=inb_p(WDT_EFDR); /* read CRF6 */
+ t = inb_p(WDT_EFDR); /* read CRF6 */
if (t != 0) {
- printk (KERN_INFO PFX "Watchdog already running. Resetting timeout to %d sec\n", timeout);
+ printk(KERN_INFO PFX
+ "Watchdog already running. Resetting timeout to %d sec\n",
+ timeout);
outb_p(timeout, WDT_EFDR); /* Write back to CRF6 */
}
outb_p(0xF5, WDT_EFER); /* Select CRF5 */
- t=inb_p(WDT_EFDR); /* read CRF5 */
- t&=~0x0C; /* set second mode & disable keyboard turning off watchdog */
+ t = inb_p(WDT_EFDR); /* read CRF5 */
+ t &= ~0x0C; /* set second mode & disable keyboard
+ turning off watchdog */
outb_p(t, WDT_EFDR); /* Write back to CRF5 */
outb_p(0xF7, WDT_EFER); /* Select CRF7 */
- t=inb_p(WDT_EFDR); /* read CRF7 */
- t&=~0xC0; /* disable keyboard & mouse turning off watchdog */
+ t = inb_p(WDT_EFDR); /* read CRF7 */
+ t &= ~0xC0; /* disable keyboard & mouse turning off
+ watchdog */
outb_p(t, WDT_EFDR); /* Write back to CRF7 */
w83627hf_unselect_wd_register();
}
-static void
-wdt_ctrl(int timeout)
+static void wdt_ctrl(int timeout)
{
spin_lock(&io_lock);
spin_unlock(&io_lock);
}
-static int
-wdt_ping(void)
+static int wdt_ping(void)
{
wdt_ctrl(timeout);
return 0;
}
-static int
-wdt_disable(void)
+static int wdt_disable(void)
{
wdt_ctrl(0);
return 0;
}
-static int
-wdt_set_heartbeat(int t)
+static int wdt_set_heartbeat(int t)
{
- if ((t < 1) || (t > 255))
+ if (t < 1 || t > 255)
return -EINVAL;
-
timeout = t;
return 0;
}
-static ssize_t
-wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t wdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
for (i = 0; i != count; i++) {
char c;
- if (get_user(c, buf+i))
+ if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
return count;
}
-static int
-wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_timeout;
static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "W83627HF WDT",
};
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof(ident)))
- return -EFAULT;
- break;
-
+ if (copy_to_user(argp, &ident, sizeof(ident)))
+ return -EFAULT;
+ break;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
-
- case WDIOC_KEEPALIVE:
- wdt_ping();
- break;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, p))
- return -EFAULT;
- if (wdt_set_heartbeat(new_timeout))
- return -EINVAL;
- wdt_ping();
- /* Fall */
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
+ return put_user(0, p);
case WDIOC_SETOPTIONS:
{
- int options, retval = -EINVAL;
-
- if (get_user(options, p))
- return -EFAULT;
-
- if (options & WDIOS_DISABLECARD) {
- wdt_disable();
- retval = 0;
- }
-
- if (options & WDIOS_ENABLECARD) {
- wdt_ping();
- retval = 0;
- }
+ int options, retval = -EINVAL;
- return retval;
+ if (get_user(options, p))
+ return -EFAULT;
+ if (options & WDIOS_DISABLECARD) {
+ wdt_disable();
+ retval = 0;
+ }
+ if (options & WDIOS_ENABLECARD) {
+ wdt_ping();
+ retval = 0;
+ }
+ return retval;
}
-
+ case WDIOC_KEEPALIVE:
+ wdt_ping();
+ break;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if (wdt_set_heartbeat(new_timeout))
+ return -EINVAL;
+ wdt_ping();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
default:
- return -ENOTTY;
+ return -ENOTTY;
}
return 0;
}
-static int
-wdt_open(struct inode *inode, struct file *file)
+static int wdt_open(struct inode *inode, struct file *file)
{
if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
return nonseekable_open(inode, file);
}
-static int
-wdt_close(struct inode *inode, struct file *file)
+static int wdt_close(struct inode *inode, struct file *file)
{
- if (expect_close == 42) {
+ if (expect_close == 42)
wdt_disable();
- } else {
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
wdt_ping();
}
expect_close = 0;
* Notifier for system down
*/
-static int
-wdt_notify_sys(struct notifier_block *this, unsigned long code,
+static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT) {
- /* Turn the WDT off */
- wdt_disable();
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ wdt_disable(); /* Turn the WDT off */
+
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt_write,
- .ioctl = wdt_ioctl,
+ .unlocked_ioctl = wdt_ioctl,
.open = wdt_open,
.release = wdt_close,
};
.notifier_call = wdt_notify_sys,
};
-static int __init
-wdt_init(void)
+static int __init wdt_init(void)
{
int ret;
if (wdt_set_heartbeat(timeout)) {
wdt_set_heartbeat(WATCHDOG_TIMEOUT);
- printk (KERN_INFO PFX "timeout value must be 1<=timeout<=255, using %d\n",
- WATCHDOG_TIMEOUT);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= timeout <= 255, using %d\n",
+ WATCHDOG_TIMEOUT);
}
if (!request_region(wdt_io, 1, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
+ printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
wdt_io);
ret = -EIO;
goto out;
ret = register_reboot_notifier(&wdt_notifier);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
goto unreg_regions;
}
ret = misc_register(&wdt_miscdev);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_reboot;
}
- printk (KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
- timeout, nowayout);
+ printk(KERN_INFO PFX
+ "initialized. timeout=%d sec (nowayout=%d)\n",
+ timeout, nowayout);
out:
return ret;
goto out;
}
-static void __exit
-wdt_exit(void)
+static void __exit wdt_exit(void)
{
misc_deregister(&wdt_miscdev);
unregister_reboot_notifier(&wdt_notifier);
- release_region(wdt_io,1);
+ release_region(wdt_io, 1);
}
module_init(wdt_init);
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define WATCHDOG_NAME "w83697hf/hg WDT"
/* You must set this - there is no sane way to probe for this board. */
static int wdt_io = 0x2e;
module_param(wdt_io, int, 0);
-MODULE_PARM_DESC(wdt_io, "w83697hf/hg WDT io port (default 0x2e, 0 = autodetect)");
+MODULE_PARM_DESC(wdt_io,
+ "w83697hf/hg WDT io port (default 0x2e, 0 = autodetect)");
static int timeout = WATCHDOG_TIMEOUT; /* in seconds */
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. 1<= timeout <=255 (default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. 1<= timeout <=255 (default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static int early_disable = WATCHDOG_EARLY_DISABLE;
module_param(early_disable, int, 0);
-MODULE_PARM_DESC(early_disable, "Watchdog gets disabled at boot time (default=" __MODULE_STRING(WATCHDOG_EARLY_DISABLE) ")");
+MODULE_PARM_DESC(early_disable,
+ "Watchdog gets disabled at boot time (default="
+ __MODULE_STRING(WATCHDOG_EARLY_DISABLE) ")");
/*
* Kernel methods.
*/
-#define W83697HF_EFER (wdt_io+0) /* Extended Function Enable Register */
-#define W83697HF_EFIR (wdt_io+0) /* Extended Function Index Register (same as EFER) */
-#define W83697HF_EFDR (wdt_io+1) /* Extended Function Data Register */
+#define W83697HF_EFER (wdt_io + 0) /* Extended Function Enable Register */
+#define W83697HF_EFIR (wdt_io + 0) /* Extended Function Index Register
+ (same as EFER) */
+#define W83697HF_EFDR (wdt_io + 1) /* Extended Function Data Register */
-static inline void
-w83697hf_unlock(void)
+static inline void w83697hf_unlock(void)
{
outb_p(0x87, W83697HF_EFER); /* Enter extended function mode */
outb_p(0x87, W83697HF_EFER); /* Again according to manual */
}
-static inline void
-w83697hf_lock(void)
+static inline void w83697hf_lock(void)
{
outb_p(0xAA, W83697HF_EFER); /* Leave extended function mode */
}
* w83697hf_write_timeout() must be called with the device unlocked.
*/
-static unsigned char
-w83697hf_get_reg(unsigned char reg)
+static unsigned char w83697hf_get_reg(unsigned char reg)
{
outb_p(reg, W83697HF_EFIR);
return inb_p(W83697HF_EFDR);
}
-static void
-w83697hf_set_reg(unsigned char reg, unsigned char data)
+static void w83697hf_set_reg(unsigned char reg, unsigned char data)
{
outb_p(reg, W83697HF_EFIR);
outb_p(data, W83697HF_EFDR);
}
-static void
-w83697hf_write_timeout(int timeout)
+static void w83697hf_write_timeout(int timeout)
{
- w83697hf_set_reg(0xF4, timeout); /* Write Timeout counter to CRF4 */
+ /* Write Timeout counter to CRF4 */
+ w83697hf_set_reg(0xF4, timeout);
}
-static void
-w83697hf_select_wdt(void)
+static void w83697hf_select_wdt(void)
{
w83697hf_unlock();
w83697hf_set_reg(0x07, 0x08); /* Switch to logic device 8 (GPIO2) */
}
-static inline void
-w83697hf_deselect_wdt(void)
+static inline void w83697hf_deselect_wdt(void)
{
w83697hf_lock();
}
-static void
-w83697hf_init(void)
+static void w83697hf_init(void)
{
unsigned char bbuf;
bbuf = w83697hf_get_reg(0x29);
bbuf &= ~0x60;
bbuf |= 0x20;
- w83697hf_set_reg(0x29, bbuf); /* Set pin 119 to WDTO# mode (= CR29, WDT0) */
+
+ /* Set pin 119 to WDTO# mode (= CR29, WDT0) */
+ w83697hf_set_reg(0x29, bbuf);
bbuf = w83697hf_get_reg(0xF3);
bbuf &= ~0x04;
w83697hf_deselect_wdt();
}
-static void
-wdt_ping(void)
+static void wdt_ping(void)
{
spin_lock(&io_lock);
w83697hf_select_wdt();
spin_unlock(&io_lock);
}
-static void
-wdt_enable(void)
+static void wdt_enable(void)
{
spin_lock(&io_lock);
w83697hf_select_wdt();
spin_unlock(&io_lock);
}
-static void
-wdt_disable(void)
+static void wdt_disable(void)
{
spin_lock(&io_lock);
w83697hf_select_wdt();
spin_unlock(&io_lock);
}
-static unsigned char
-wdt_running(void)
+static unsigned char wdt_running(void)
{
unsigned char t;
return t;
}
-static int
-wdt_set_heartbeat(int t)
+static int wdt_set_heartbeat(int t)
{
- if ((t < 1) || (t > 255))
+ if (t < 1 || t > 255)
return -EINVAL;
timeout = t;
return 0;
}
-static ssize_t
-wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t wdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
for (i = 0; i != count; i++) {
char c;
- if (get_user(c, buf+i))
+ if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
return count;
}
-static int
-wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
int new_timeout;
- static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "W83697HF WDT",
};
case WDIOC_GETBOOTSTATUS:
return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_ping();
- break;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, p))
- return -EFAULT;
- if (wdt_set_heartbeat(new_timeout))
- return -EINVAL;
- wdt_ping();
- /* Fall */
-
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
case WDIOC_SETOPTIONS:
{
int options, retval = -EINVAL;
return retval;
}
+ case WDIOC_KEEPALIVE:
+ wdt_ping();
+ break;
+
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if (wdt_set_heartbeat(new_timeout))
+ return -EINVAL;
+ wdt_ping();
+ /* Fall */
+
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+
default:
return -ENOTTY;
}
return 0;
}
-static int
-wdt_open(struct inode *inode, struct file *file)
+static int wdt_open(struct inode *inode, struct file *file)
{
if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
return nonseekable_open(inode, file);
}
-static int
-wdt_close(struct inode *inode, struct file *file)
+static int wdt_close(struct inode *inode, struct file *file)
{
- if (expect_close == 42) {
+ if (expect_close == 42)
wdt_disable();
- } else {
- printk (KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
wdt_ping();
}
expect_close = 0;
* Notifier for system down
*/
-static int
-wdt_notify_sys(struct notifier_block *this, unsigned long code,
+static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT) {
- /* Turn the WDT off */
- wdt_disable();
- }
+ if (code == SYS_DOWN || code == SYS_HALT)
+ wdt_disable(); /* Turn the WDT off */
+
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt_write,
- .ioctl = wdt_ioctl,
+ .unlocked_ioctl = wdt_ioctl,
.open = wdt_open,
.release = wdt_close,
};
.notifier_call = wdt_notify_sys,
};
-static int
-w83697hf_check_wdt(void)
+static int w83697hf_check_wdt(void)
{
if (!request_region(wdt_io, 2, WATCHDOG_NAME)) {
- printk (KERN_ERR PFX "I/O address 0x%x already in use\n", wdt_io);
+ printk(KERN_ERR PFX
+ "I/O address 0x%x already in use\n", wdt_io);
return -EIO;
}
- printk (KERN_DEBUG PFX "Looking for watchdog at address 0x%x\n", wdt_io);
+ printk(KERN_DEBUG PFX
+ "Looking for watchdog at address 0x%x\n", wdt_io);
w83697hf_unlock();
if (w83697hf_get_reg(0x20) == 0x60) {
- printk (KERN_INFO PFX "watchdog found at address 0x%x\n", wdt_io);
+ printk(KERN_INFO PFX
+ "watchdog found at address 0x%x\n", wdt_io);
w83697hf_lock();
return 0;
}
- w83697hf_lock(); /* Reprotect in case it was a compatible device */
+ /* Reprotect in case it was a compatible device */
+ w83697hf_lock();
- printk (KERN_INFO PFX "watchdog not found at address 0x%x\n", wdt_io);
+ printk(KERN_INFO PFX "watchdog not found at address 0x%x\n", wdt_io);
release_region(wdt_io, 2);
return -EIO;
}
static int w83697hf_ioports[] = { 0x2e, 0x4e, 0x00 };
-static int __init
-wdt_init(void)
+static int __init wdt_init(void)
{
int ret, i, found = 0;
- printk (KERN_INFO PFX "WDT driver for W83697HF/HG initializing\n");
+ printk(KERN_INFO PFX "WDT driver for W83697HF/HG initializing\n");
if (wdt_io == 0) {
/* we will autodetect the W83697HF/HG watchdog */
}
if (!found) {
- printk (KERN_ERR PFX "No W83697HF/HG could be found\n");
+ printk(KERN_ERR PFX "No W83697HF/HG could be found\n");
ret = -EIO;
goto out;
}
w83697hf_init();
if (early_disable) {
if (wdt_running())
- printk (KERN_WARNING PFX "Stopping previously enabled watchdog until userland kicks in\n");
+ printk(KERN_WARNING PFX "Stopping previously enabled watchdog until userland kicks in\n");
wdt_disable();
}
if (wdt_set_heartbeat(timeout)) {
wdt_set_heartbeat(WATCHDOG_TIMEOUT);
- printk (KERN_INFO PFX "timeout value must be 1<=timeout<=255, using %d\n",
- WATCHDOG_TIMEOUT);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= timeout <= 255, using %d\n",
+ WATCHDOG_TIMEOUT);
}
ret = register_reboot_notifier(&wdt_notifier);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
goto unreg_regions;
}
ret = misc_register(&wdt_miscdev);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto unreg_reboot;
}
- printk (KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
+ printk(KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
out:
goto out;
}
-static void __exit
-wdt_exit(void)
+static void __exit wdt_exit(void)
{
misc_deregister(&wdt_miscdev);
unregister_reboot_notifier(&wdt_notifier);
* Added KERN_* tags to printks
* add CONFIG_WATCHDOG_NOWAYOUT support
* fix possible wdt_is_open race
- * changed watchdog_info to correctly reflect what the driver offers
- * added WDIOC_GETSTATUS, WDIOC_GETBOOTSTATUS, WDIOC_SETTIMEOUT,
+ * changed watchdog_info to correctly reflect what
+ * the driver offers
+ * added WDIOC_GETSTATUS, WDIOC_GETBOOTSTATUS,
+ * WDIOC_SETTIMEOUT,
* WDIOC_GETTIMEOUT, and WDIOC_SETOPTIONS ioctls
* 09/8 - 2003 [wim@iguana.be] cleanup of trailing spaces
* added extra printk's for startup problems
* use module_param
- * made timeout (the emulated heartbeat) a module_param
+ * made timeout (the emulated heartbeat) a
+ * module_param
* made the keepalive ping an internal subroutine
*
* This WDT driver is different from most other Linux WDT
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#include <asm/system.h>
#define OUR_NAME "w83877f_wdt"
*/
#define WATCHDOG_TIMEOUT 30 /* 30 sec default timeout */
-static int timeout = WATCHDOG_TIMEOUT; /* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+/* in seconds, will be multiplied by HZ to get seconds to wait for a ping */
+static int timeout = WATCHDOG_TIMEOUT;
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. (1<=timeout<=3600, default=" __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. (1<=timeout<=3600, default="
+ __MODULE_STRING(WATCHDOG_TIMEOUT) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static void wdt_timer_ping(unsigned long);
static DEFINE_TIMER(timer, wdt_timer_ping, 0, 0);
/* If we got a heartbeat pulse within the WDT_US_INTERVAL
* we agree to ping the WDT
*/
- if(time_before(jiffies, next_heartbeat))
- {
+ if (time_before(jiffies, next_heartbeat)) {
/* Ping the WDT */
spin_lock(&wdt_spinlock);
spin_unlock(&wdt_spinlock);
- } else {
- printk(KERN_WARNING PFX "Heartbeat lost! Will not ping the watchdog\n");
- }
+ } else
+ printk(KERN_WARNING PFX
+ "Heartbeat lost! Will not ping the watchdog\n");
}
/*
* /dev/watchdog handling
*/
-static ssize_t fop_write(struct file * file, const char __user * buf, size_t count, loff_t * ppos)
+static ssize_t fop_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count)
- {
- if (!nowayout)
- {
+ if (count) {
+ if (!nowayout) {
size_t ofs;
- /* note: just in case someone wrote the magic character
- * five months ago... */
+ /* note: just in case someone wrote the magic
+ character five months ago... */
wdt_expect_close = 0;
- /* scan to see whether or not we got the magic character */
- for(ofs = 0; ofs != count; ofs++)
- {
+ /* scan to see whether or not we got the
+ magic character */
+ for (ofs = 0; ofs != count; ofs++) {
char c;
if (get_user(c, buf + ofs))
return -EFAULT;
return count;
}
-static int fop_open(struct inode * inode, struct file * file)
+static int fop_open(struct inode *inode, struct file *file)
{
/* Just in case we're already talking to someone... */
- if(test_and_set_bit(0, &wdt_is_open))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
/* Good, fire up the show */
return nonseekable_open(inode, file);
}
-static int fop_close(struct inode * inode, struct file * file)
+static int fop_close(struct inode *inode, struct file *file)
{
- if(wdt_expect_close == 42)
+ if (wdt_expect_close == 42)
wdt_turnoff();
else {
del_timer(&timer);
- printk(KERN_CRIT PFX "device file closed unexpectedly. Will not stop the WDT!\n");
+ printk(KERN_CRIT PFX
+ "device file closed unexpectedly. Will not stop the WDT!\n");
}
clear_bit(0, &wdt_is_open);
wdt_expect_close = 0;
return 0;
}
-static int fop_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long fop_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident=
- {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT
+ | WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "W83877F",
};
- switch(cmd)
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_SETOPTIONS:
{
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
- case WDIOC_GETSTATUS:
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
- case WDIOC_SETOPTIONS:
- {
- int new_options, retval = -EINVAL;
-
- if(get_user(new_options, p))
- return -EFAULT;
-
- if(new_options & WDIOS_DISABLECARD) {
- wdt_turnoff();
- retval = 0;
- }
+ int new_options, retval = -EINVAL;
- if(new_options & WDIOS_ENABLECARD) {
- wdt_startup();
- retval = 0;
- }
+ if (get_user(new_options, p))
+ return -EFAULT;
- return retval;
+ if (new_options & WDIOS_DISABLECARD) {
+ wdt_turnoff();
+ retval = 0;
}
- case WDIOC_SETTIMEOUT:
- {
- int new_timeout;
- if(get_user(new_timeout, p))
- return -EFAULT;
+ if (new_options & WDIOS_ENABLECARD) {
+ wdt_startup();
+ retval = 0;
+ }
- if(new_timeout < 1 || new_timeout > 3600) /* arbitrary upper limit */
- return -EINVAL;
+ return retval;
+ }
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ {
+ int new_timeout;
- timeout = new_timeout;
- wdt_keepalive();
- /* Fall through */
- }
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+
+ /* arbitrary upper limit */
+ if (new_timeout < 1 || new_timeout > 3600)
+ return -EINVAL;
+
+ timeout = new_timeout;
+ wdt_keepalive();
+ /* Fall through */
+ }
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+ default:
+ return -ENOTTY;
}
}
.write = fop_write,
.open = fop_open,
.release = fop_close,
- .ioctl = fop_ioctl,
+ .unlocked_ioctl = fop_ioctl,
};
static struct miscdevice wdt_miscdev = {
static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_turnoff();
return NOTIFY_DONE;
}
* turn the timebomb registers off.
*/
-static struct notifier_block wdt_notifier=
-{
+static struct notifier_block wdt_notifier = {
.notifier_call = wdt_notify_sys,
};
misc_deregister(&wdt_miscdev);
unregister_reboot_notifier(&wdt_notifier);
- release_region(WDT_PING,1);
- release_region(ENABLE_W83877F_PORT,2);
+ release_region(WDT_PING, 1);
+ release_region(ENABLE_W83877F_PORT, 2);
}
static int __init w83877f_wdt_init(void)
{
int rc = -EBUSY;
- if(timeout < 1 || timeout > 3600) /* arbitrary upper limit */
- {
+ if (timeout < 1 || timeout > 3600) { /* arbitrary upper limit */
timeout = WATCHDOG_TIMEOUT;
- printk(KERN_INFO PFX "timeout value must be 1<=x<=3600, using %d\n",
- timeout);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= x <= 3600, using %d\n",
+ timeout);
}
- if (!request_region(ENABLE_W83877F_PORT, 2, "W83877F WDT"))
- {
+ if (!request_region(ENABLE_W83877F_PORT, 2, "W83877F WDT")) {
printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
ENABLE_W83877F_PORT);
rc = -EIO;
goto err_out;
}
- if (!request_region(WDT_PING, 1, "W8387FF WDT"))
- {
+ if (!request_region(WDT_PING, 1, "W8387FF WDT")) {
printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
WDT_PING);
rc = -EIO;
}
rc = register_reboot_notifier(&wdt_notifier);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out_region2;
}
rc = misc_register(&wdt_miscdev);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- wdt_miscdev.minor, rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ wdt_miscdev.minor, rc);
goto err_out_reboot;
}
- printk(KERN_INFO PFX "WDT driver for W83877F initialised. timeout=%d sec (nowayout=%d)\n",
+ printk(KERN_INFO PFX
+ "WDT driver for W83877F initialised. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
return 0;
err_out_reboot:
unregister_reboot_notifier(&wdt_notifier);
err_out_region2:
- release_region(WDT_PING,1);
+ release_region(WDT_PING, 1);
err_out_region1:
- release_region(ENABLE_W83877F_PORT,2);
+ release_region(ENABLE_W83877F_PORT, 2);
err_out:
return rc;
}
#include <linux/watchdog.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
-#include <asm/io.h>
#include <asm/system.h>
-#include <asm/uaccess.h>
#define WATCHDOG_VERSION "1.00"
#define WATCHDOG_NAME "W83977F WDT"
static DEFINE_SPINLOCK(spinlock);
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout,"Watchdog timeout in seconds (15..7635), default=" __MODULE_STRING(DEFAULT_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds (15..7635), default="
+ __MODULE_STRING(DEFAULT_TIMEOUT) ")");
module_param(testmode, int, 0);
-MODULE_PARM_DESC(testmode,"Watchdog testmode (1 = no reboot), default=0");
+MODULE_PARM_DESC(testmode, "Watchdog testmode (1 = no reboot), default=0");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Start the watchdog
spin_lock_irqsave(&spinlock, flags);
/* Unlock the SuperIO chip */
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
/*
* Select device Aux2 (device=8) to set watchdog regs F2, F3 and F4.
* F3 is set to enable watchdog LED blink at timeout.
* F4 is used to just clear the TIMEOUT'ed state (bit 0).
*/
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
- outb_p(0xF2,IO_INDEX_PORT);
- outb_p(timeoutW,IO_DATA_PORT);
- outb_p(0xF3,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
- outb_p(0xF4,IO_INDEX_PORT);
- outb_p(0x00,IO_DATA_PORT);
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
+ outb_p(0xF2, IO_INDEX_PORT);
+ outb_p(timeoutW, IO_DATA_PORT);
+ outb_p(0xF3, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
+ outb_p(0xF4, IO_INDEX_PORT);
+ outb_p(0x00, IO_DATA_PORT);
/* Set device Aux2 active */
- outb_p(0x30,IO_INDEX_PORT);
- outb_p(0x01,IO_DATA_PORT);
+ outb_p(0x30, IO_INDEX_PORT);
+ outb_p(0x01, IO_DATA_PORT);
- /*
+ /*
* Select device Aux1 (dev=7) to set GP16 as the watchdog output
* (in reg E6) and GP13 as the watchdog LED output (in reg E3).
* Map GP16 at pin 119.
* In test mode watch the bit 0 on F4 to indicate "triggered" or
* check watchdog LED on SBC.
*/
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x07,IO_DATA_PORT);
- if (!testmode)
- {
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x07, IO_DATA_PORT);
+ if (!testmode) {
unsigned pin_map;
- outb_p(0xE6,IO_INDEX_PORT);
- outb_p(0x0A,IO_DATA_PORT);
- outb_p(0x2C,IO_INDEX_PORT);
+ outb_p(0xE6, IO_INDEX_PORT);
+ outb_p(0x0A, IO_DATA_PORT);
+ outb_p(0x2C, IO_INDEX_PORT);
pin_map = inb_p(IO_DATA_PORT);
pin_map |= 0x10;
pin_map &= ~(0x20);
- outb_p(0x2C,IO_INDEX_PORT);
- outb_p(pin_map,IO_DATA_PORT);
+ outb_p(0x2C, IO_INDEX_PORT);
+ outb_p(pin_map, IO_DATA_PORT);
}
- outb_p(0xE3,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
+ outb_p(0xE3, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
/* Set device Aux1 active */
- outb_p(0x30,IO_INDEX_PORT);
- outb_p(0x01,IO_DATA_PORT);
+ outb_p(0x30, IO_INDEX_PORT);
+ outb_p(0x01, IO_DATA_PORT);
/* Lock the SuperIO chip */
- outb_p(LOCK_DATA,IO_INDEX_PORT);
+ outb_p(LOCK_DATA, IO_INDEX_PORT);
spin_unlock_irqrestore(&spinlock, flags);
spin_lock_irqsave(&spinlock, flags);
/* Unlock the SuperIO chip */
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
- /*
+ /*
* Select device Aux2 (device=8) to set watchdog regs F2, F3 and F4.
* F2 is reset to its default value (watchdog timer disabled).
* F3 is reset to its default state.
* F4 clears the TIMEOUT'ed state (bit 0) - back to default.
*/
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
- outb_p(0xF2,IO_INDEX_PORT);
- outb_p(0xFF,IO_DATA_PORT);
- outb_p(0xF3,IO_INDEX_PORT);
- outb_p(0x00,IO_DATA_PORT);
- outb_p(0xF4,IO_INDEX_PORT);
- outb_p(0x00,IO_DATA_PORT);
- outb_p(0xF2,IO_INDEX_PORT);
- outb_p(0x00,IO_DATA_PORT);
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
+ outb_p(0xF2, IO_INDEX_PORT);
+ outb_p(0xFF, IO_DATA_PORT);
+ outb_p(0xF3, IO_INDEX_PORT);
+ outb_p(0x00, IO_DATA_PORT);
+ outb_p(0xF4, IO_INDEX_PORT);
+ outb_p(0x00, IO_DATA_PORT);
+ outb_p(0xF2, IO_INDEX_PORT);
+ outb_p(0x00, IO_DATA_PORT);
/*
- * Select device Aux1 (dev=7) to set GP16 (in reg E6) and
+ * Select device Aux1 (dev=7) to set GP16 (in reg E6) and
* Gp13 (in reg E3) as inputs.
*/
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x07,IO_DATA_PORT);
- if (!testmode)
- {
- outb_p(0xE6,IO_INDEX_PORT);
- outb_p(0x01,IO_DATA_PORT);
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x07, IO_DATA_PORT);
+ if (!testmode) {
+ outb_p(0xE6, IO_INDEX_PORT);
+ outb_p(0x01, IO_DATA_PORT);
}
- outb_p(0xE3,IO_INDEX_PORT);
- outb_p(0x01,IO_DATA_PORT);
+ outb_p(0xE3, IO_INDEX_PORT);
+ outb_p(0x01, IO_DATA_PORT);
/* Lock the SuperIO chip */
- outb_p(LOCK_DATA,IO_INDEX_PORT);
+ outb_p(LOCK_DATA, IO_INDEX_PORT);
spin_unlock_irqrestore(&spinlock, flags);
spin_lock_irqsave(&spinlock, flags);
/* Unlock the SuperIO chip */
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
/* Select device Aux2 (device=8) to kick watchdog reg F2 */
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
- outb_p(0xF2,IO_INDEX_PORT);
- outb_p(timeoutW,IO_DATA_PORT);
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
+ outb_p(0xF2, IO_INDEX_PORT);
+ outb_p(timeoutW, IO_DATA_PORT);
/* Lock the SuperIO chip */
- outb_p(LOCK_DATA,IO_INDEX_PORT);
+ outb_p(LOCK_DATA, IO_INDEX_PORT);
spin_unlock_irqrestore(&spinlock, flags);
/*
* Convert seconds to watchdog counter time units, rounding up.
- * On PCM-5335 watchdog units are 30 seconds/step with 15 sec startup
+ * On PCM-5335 watchdog units are 30 seconds/step with 15 sec startup
* value. This information is supplied in the PCM-5335 manual and was
* checked by me on a real board. This is a bit strange because W83977f
* datasheet says counter unit is in minutes!
return -EINVAL;
/*
- * timeout is the timeout in seconds,
+ * timeout is the timeout in seconds,
* timeoutW is the timeout in watchdog counter units.
*/
timeoutW = tmrval;
spin_lock_irqsave(&spinlock, flags);
/* Unlock the SuperIO chip */
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
- outb_p(UNLOCK_DATA,IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
+ outb_p(UNLOCK_DATA, IO_INDEX_PORT);
/* Select device Aux2 (device=8) to read watchdog reg F4 */
- outb_p(DEVICE_REGISTER,IO_INDEX_PORT);
- outb_p(0x08,IO_DATA_PORT);
- outb_p(0xF4,IO_INDEX_PORT);
+ outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
+ outb_p(0x08, IO_DATA_PORT);
+ outb_p(0xF4, IO_INDEX_PORT);
new_status = inb_p(IO_DATA_PORT);
/* Lock the SuperIO chip */
- outb_p(LOCK_DATA,IO_INDEX_PORT);
+ outb_p(LOCK_DATA, IO_INDEX_PORT);
spin_unlock_irqrestore(&spinlock, flags);
static int wdt_open(struct inode *inode, struct file *file)
{
/* If the watchdog is alive we don't need to start it again */
- if( test_and_set_bit(0, &timer_alive) )
+ if (test_and_set_bit(0, &timer_alive))
return -EBUSY;
if (nowayout)
* Shut off the timer.
* Lock it in if it's a module and we set nowayout
*/
- if (expect_close == 42)
- {
+ if (expect_close == 42) {
wdt_stop();
clear_bit(0, &timer_alive);
} else {
wdt_keepalive();
- printk(KERN_CRIT PFX "unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "unexpected close, not stopping watchdog!\n");
}
expect_close = 0;
return 0;
size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
- if(count)
- {
- if (!nowayout)
- {
+ if (count) {
+ if (!nowayout) {
size_t ofs;
- /* note: just in case someone wrote the magic character long ago */
+ /* note: just in case someone wrote the
+ magic character long ago */
expect_close = 0;
- /* scan to see whether or not we got the magic character */
- for(ofs = 0; ofs != count; ofs++)
- {
+ /* scan to see whether or not we got the
+ magic character */
+ for (ofs = 0; ofs != count; ofs++) {
char c;
if (get_user(c, buf + ofs))
return -EFAULT;
- if (c == 'V') {
+ if (c == 'V')
expect_close = 42;
- }
}
}
.identity = WATCHDOG_NAME,
};
-static int wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
int status;
int new_options, retval = -EINVAL;
uarg.i = (int __user *)arg;
- switch(cmd)
- {
- default:
- return -ENOTTY;
-
+ switch (cmd) {
case WDIOC_GETSUPPORT:
- return copy_to_user(uarg.ident, &ident, sizeof(ident)) ? -EFAULT : 0;
+ return copy_to_user(uarg.ident, &ident,
+ sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETSTATUS:
wdt_get_status(&status);
case WDIOC_GETBOOTSTATUS:
return put_user(0, uarg.i);
- case WDIOC_KEEPALIVE:
- wdt_keepalive();
- return 0;
-
case WDIOC_SETOPTIONS:
- if (get_user (new_options, uarg.i))
+ if (get_user(new_options, uarg.i))
return -EFAULT;
if (new_options & WDIOS_DISABLECARD) {
return retval;
+ case WDIOC_KEEPALIVE:
+ wdt_keepalive();
+ return 0;
+
case WDIOC_SETTIMEOUT:
if (get_user(new_timeout, uarg.i))
return -EFAULT;
case WDIOC_GETTIMEOUT:
return put_user(timeout, uarg.i);
+ default:
+ return -ENOTTY;
+
}
}
static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_stop();
return NOTIFY_DONE;
}
-static const struct file_operations wdt_fops=
-{
+static const struct file_operations wdt_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt_write,
- .ioctl = wdt_ioctl,
+ .unlocked_ioctl = wdt_ioctl,
.open = wdt_open,
.release = wdt_release,
};
-static struct miscdevice wdt_miscdev=
-{
+static struct miscdevice wdt_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &wdt_fops,
{
int rc;
- printk(KERN_INFO PFX DRIVER_VERSION);
+ printk(KERN_INFO PFX DRIVER_VERSION);
/*
- * Check that the timeout value is within it's range ;
+ * Check that the timeout value is within it's range;
* if not reset to the default
*/
if (wdt_set_timeout(timeout)) {
wdt_set_timeout(DEFAULT_TIMEOUT);
- printk(KERN_INFO PFX "timeout value must be 15<=timeout<=7635, using %d\n",
- DEFAULT_TIMEOUT);
+ printk(KERN_INFO PFX
+ "timeout value must be 15 <= timeout <= 7635, using %d\n",
+ DEFAULT_TIMEOUT);
}
- if (!request_region(IO_INDEX_PORT, 2, WATCHDOG_NAME))
- {
+ if (!request_region(IO_INDEX_PORT, 2, WATCHDOG_NAME)) {
printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
IO_INDEX_PORT);
rc = -EIO;
}
rc = register_reboot_notifier(&wdt_notifier);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out_region;
}
rc = misc_register(&wdt_miscdev);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- wdt_miscdev.minor, rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ wdt_miscdev.minor, rc);
goto err_out_reboot;
}
- printk(KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d testmode=%d)\n",
- timeout, nowayout, testmode);
+ printk(KERN_INFO PFX
+ "initialized. timeout=%d sec (nowayout=%d testmode=%d)\n",
+ timeout, nowayout, testmode);
return 0;
err_out_reboot:
unregister_reboot_notifier(&wdt_notifier);
err_out_region:
- release_region(IO_INDEX_PORT,2);
+ release_region(IO_INDEX_PORT, 2);
err_out:
return rc;
}
wdt_stop();
misc_deregister(&wdt_miscdev);
unregister_reboot_notifier(&wdt_notifier);
- release_region(IO_INDEX_PORT,2);
+ release_region(IO_INDEX_PORT, 2);
}
module_init(w83977f_wdt_init);
/*
* ICP Wafer 5823 Single Board Computer WDT driver
- * http://www.icpamerica.com/wafer_5823.php
- * May also work on other similar models
+ * http://www.icpamerica.com/wafer_5823.php
+ * May also work on other similar models
*
* (c) Copyright 2002 Justin Cormack <justin@street-vision.com>
*
- * Release 0.02
+ * Release 0.02
*
* Based on advantechwdt.c which is based on wdt.c.
* Original copyright messages:
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/spinlock.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
#define WATCHDOG_NAME "Wafer 5823 WDT"
#define PFX WATCHDOG_NAME ": "
/*
* You must set these - there is no sane way to probe for this board.
*
- * To enable, write the timeout value in seconds (1 to 255) to I/O
- * port WDT_START, then read the port to start the watchdog. To pat
- * the dog, read port WDT_STOP to stop the timer, then read WDT_START
- * to restart it again.
+ * To enable, write the timeout value in seconds (1 to 255) to I/O
+ * port WDT_START, then read the port to start the watchdog. To pat
+ * the dog, read port WDT_STOP to stop the timer, then read WDT_START
+ * to restart it again.
*/
static int wdt_stop = 0x843;
static int timeout = WD_TIMO; /* in seconds */
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds. 1<= timeout <=255, default=" __MODULE_STRING(WD_TIMO) ".");
+MODULE_PARM_DESC(timeout,
+ "Watchdog timeout in seconds. 1 <= timeout <= 255, default="
+ __MODULE_STRING(WD_TIMO) ".");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
static void wafwdt_ping(void)
{
inb_p(wdt_start);
}
-static void
-wafwdt_stop(void)
+static void wafwdt_stop(void)
{
/* stop watchdog */
inb_p(wdt_stop);
}
-static ssize_t wafwdt_write(struct file *file, const char __user *buf, size_t count, loff_t * ppos)
+static ssize_t wafwdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
/* See if we got the magic character 'V' and reload the timer */
if (count) {
/* In case it was set long ago */
expect_close = 0;
- /* scan to see whether or not we got the magic character */
+ /* scan to see whether or not we got the magic
+ character */
for (i = 0; i != count; i++) {
char c;
if (get_user(c, buf + i))
expect_close = 42;
}
}
- /* Well, anyhow someone wrote to us, we should return that favour */
+ /* Well, anyhow someone wrote to us, we should
+ return that favour */
wafwdt_ping();
}
return count;
}
-static int wafwdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long wafwdt_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_timeout;
void __user *argp = (void __user *)arg;
int __user *p = argp;
- static struct watchdog_info ident = {
- .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT | WDIOF_MAGICCLOSE,
+ static const struct watchdog_info ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE,
.firmware_version = 1,
.identity = "Wafer 5823 WDT",
};
switch (cmd) {
case WDIOC_GETSUPPORT:
- if (copy_to_user(argp, &ident, sizeof (ident)))
+ if (copy_to_user(argp, &ident, sizeof(ident)))
return -EFAULT;
break;
case WDIOC_GETBOOTSTATUS:
return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wafwdt_ping();
- break;
-
- case WDIOC_SETTIMEOUT:
- if (get_user(new_timeout, p))
- return -EFAULT;
- if ((new_timeout < 1) || (new_timeout > 255))
- return -EINVAL;
- timeout = new_timeout;
- wafwdt_stop();
- wafwdt_start();
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(timeout, p);
-
case WDIOC_SETOPTIONS:
{
int options, retval = -EINVAL;
return retval;
}
+ case WDIOC_KEEPALIVE:
+ wafwdt_ping();
+ break;
+
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_timeout, p))
+ return -EFAULT;
+ if ((new_timeout < 1) || (new_timeout > 255))
+ return -EINVAL;
+ timeout = new_timeout;
+ wafwdt_stop();
+ wafwdt_start();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(timeout, p);
+
default:
return -ENOTTY;
}
return nonseekable_open(inode, file);
}
-static int
-wafwdt_close(struct inode *inode, struct file *file)
+static int wafwdt_close(struct inode *inode, struct file *file)
{
- if (expect_close == 42) {
+ if (expect_close == 42)
wafwdt_stop();
- } else {
- printk(KERN_CRIT PFX "WDT device closed unexpectedly. WDT will not stop!\n");
+ else {
+ printk(KERN_CRIT PFX
+ "WDT device closed unexpectedly. WDT will not stop!\n");
wafwdt_ping();
}
clear_bit(0, &wafwdt_is_open);
* Notifier for system down
*/
-static int wafwdt_notify_sys(struct notifier_block *this, unsigned long code, void *unused)
+static int wafwdt_notify_sys(struct notifier_block *this, unsigned long code,
+ void *unused)
{
- if (code == SYS_DOWN || code == SYS_HALT) {
- /* Turn the WDT off */
+ if (code == SYS_DOWN || code == SYS_HALT)
wafwdt_stop();
- }
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wafwdt_write,
- .ioctl = wafwdt_ioctl,
+ .unlocked_ioctl = wafwdt_ioctl,
.open = wafwdt_open,
.release = wafwdt_close,
};
{
int ret;
- printk(KERN_INFO "WDT driver for Wafer 5823 single board computer initialising.\n");
+ printk(KERN_INFO
+ "WDT driver for Wafer 5823 single board computer initialising.\n");
if (timeout < 1 || timeout > 255) {
timeout = WD_TIMO;
- printk (KERN_INFO PFX "timeout value must be 1<=x<=255, using %d\n",
- timeout);
+ printk(KERN_INFO PFX
+ "timeout value must be 1 <= x <= 255, using %d\n",
+ timeout);
}
if (wdt_stop != wdt_start) {
- if(!request_region(wdt_stop, 1, "Wafer 5823 WDT")) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
- wdt_stop);
+ if (!request_region(wdt_stop, 1, "Wafer 5823 WDT")) {
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n",
+ wdt_stop);
ret = -EIO;
goto error;
}
}
- if(!request_region(wdt_start, 1, "Wafer 5823 WDT")) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n",
+ if (!request_region(wdt_start, 1, "Wafer 5823 WDT")) {
+ printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
wdt_start);
ret = -EIO;
goto error2;
ret = register_reboot_notifier(&wafwdt_notifier);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
goto error3;
}
ret = misc_register(&wafwdt_miscdev);
if (ret != 0) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto error4;
}
- printk (KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
+ printk(KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d)\n",
timeout, nowayout);
return ret;
{
misc_deregister(&wafwdt_miscdev);
unregister_reboot_notifier(&wafwdt_notifier);
- if(wdt_stop != wdt_start)
+ if (wdt_stop != wdt_start)
release_region(wdt_stop, 1);
release_region(wdt_start, 1);
}
* http://www.cymru.net
*
* This driver is provided under the GNU General Public License, incorporated
- * herein by reference. The driver is provided without warranty or
+ * herein by reference. The driver is provided without warranty or
* support.
*
* Release 0.04.
#include <linux/reboot.h>
#include <linux/types.h>
#include <linux/watchdog.h>
+#include <linux/uaccess.h>
#include <asm/rtas.h>
-#include <asm/uaccess.h>
#define WDRTAS_MAGIC_CHAR 42
#define WDRTAS_SUPPORTED_MASK (WDIOF_SETTIMEOUT | \
#endif
static atomic_t wdrtas_miscdev_open = ATOMIC_INIT(0);
-static char wdrtas_expect_close = 0;
+static char wdrtas_expect_close;
static int wdrtas_interval;
* RTAS function set-indicator (surveillance). The unit of interval is
* seconds.
*/
-static int
-wdrtas_set_interval(int interval)
+
+static int wdrtas_set_interval(int interval)
{
long result;
static int print_msg = 10;
result = rtas_call(wdrtas_token_set_indicator, 3, 1, NULL,
WDRTAS_SURVEILLANCE_IND, 0, interval);
- if ( (result < 0) && (print_msg) ) {
+ if (result < 0 && print_msg) {
printk(KERN_ERR "wdrtas: setting the watchdog to %i "
"timeout failed: %li\n", interval, result);
print_msg--;
* as reported by the RTAS function ibm,get-system-parameter. The unit
* of the return value is seconds.
*/
-static int
-wdrtas_get_interval(int fallback_value)
+static int wdrtas_get_interval(int fallback_value)
{
long result;
char value[4];
result = rtas_call(wdrtas_token_get_sp, 3, 1, NULL,
WDRTAS_SP_SPI, (void *)__pa(&value), 4);
- if ( (value[0] != 0) || (value[1] != 2) || (value[3] != 0) ||
- (result < 0) ) {
+ if (value[0] != 0 || value[1] != 2 || value[3] != 0 || result < 0) {
printk(KERN_WARNING "wdrtas: could not get sp_spi watchdog "
"timeout (%li). Continuing\n", result);
return fallback_value;
* wdrtas_timer_start starts the watchdog by calling the RTAS function
* set-interval (surveillance)
*/
-static void
-wdrtas_timer_start(void)
+static void wdrtas_timer_start(void)
{
wdrtas_set_interval(wdrtas_interval);
}
* wdrtas_timer_stop stops the watchdog timer by calling the RTAS function
* set-interval (surveillance)
*/
-static void
-wdrtas_timer_stop(void)
+static void wdrtas_timer_stop(void)
{
wdrtas_set_interval(0);
}
* wdrtas_log_scanned_event prints a message to the log buffer dumping
* the results of the last event-scan call
*/
-static void
-wdrtas_log_scanned_event(void)
+static void wdrtas_log_scanned_event(void)
{
int i;
"%02x %02x %02x %02x %02x %02x %02x %02x "
"%02x %02x %02x %02x %02x %02x %02x %02x\n",
(i / 16) + 1, (WDRTAS_LOGBUFFER_LEN / 16),
- wdrtas_logbuffer[i + 0], wdrtas_logbuffer[i + 1],
- wdrtas_logbuffer[i + 2], wdrtas_logbuffer[i + 3],
- wdrtas_logbuffer[i + 4], wdrtas_logbuffer[i + 5],
- wdrtas_logbuffer[i + 6], wdrtas_logbuffer[i + 7],
- wdrtas_logbuffer[i + 8], wdrtas_logbuffer[i + 9],
- wdrtas_logbuffer[i + 10], wdrtas_logbuffer[i + 11],
- wdrtas_logbuffer[i + 12], wdrtas_logbuffer[i + 13],
+ wdrtas_logbuffer[i + 0], wdrtas_logbuffer[i + 1],
+ wdrtas_logbuffer[i + 2], wdrtas_logbuffer[i + 3],
+ wdrtas_logbuffer[i + 4], wdrtas_logbuffer[i + 5],
+ wdrtas_logbuffer[i + 6], wdrtas_logbuffer[i + 7],
+ wdrtas_logbuffer[i + 8], wdrtas_logbuffer[i + 9],
+ wdrtas_logbuffer[i + 10], wdrtas_logbuffer[i + 11],
+ wdrtas_logbuffer[i + 12], wdrtas_logbuffer[i + 13],
wdrtas_logbuffer[i + 14], wdrtas_logbuffer[i + 15]);
}
* RTAS function event-scan and repeats these calls as long as there are
* events available. All events will be dumped.
*/
-static void
-wdrtas_timer_keepalive(void)
+static void wdrtas_timer_keepalive(void)
{
long result;
* wdrtas_get_temperature returns the current temperature in Fahrenheit. It
* uses the RTAS call get-sensor-state, token 3 to do so
*/
-static int
-wdrtas_get_temperature(void)
+static int wdrtas_get_temperature(void)
{
long result;
int temperature = 0;
* returns a bitmask of defines WDIOF_... as defined in
* include/linux/watchdog.h
*/
-static int
-wdrtas_get_status(void)
+static int wdrtas_get_status(void)
{
return 0; /* TODO */
}
* returns a bitmask of defines WDIOF_... as defined in
* include/linux/watchdog.h, indicating why the watchdog rebooted the system
*/
-static int
-wdrtas_get_boot_status(void)
+static int wdrtas_get_boot_status(void)
{
return 0; /* TODO */
}
* character 'V'. This character allows the watchdog device to be closed
* properly.
*/
-static ssize_t
-wdrtas_write(struct file *file, const char __user *buf,
+static ssize_t wdrtas_write(struct file *file, const char __user *buf,
size_t len, loff_t *ppos)
{
int i;
/**
* wdrtas_ioctl - ioctl function for the watchdog device
- * @inode: inode structure
* @file: file structure
* @cmd: command for ioctl
* @arg: argument pointer
*
* wdrtas_ioctl implements the watchdog API ioctls
*/
-static int
-wdrtas_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+
+static long wdrtas_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int __user *argp = (void __user *)arg;
int i;
static struct watchdog_info wdinfo = {
.options = WDRTAS_SUPPORTED_MASK,
.firmware_version = 0,
- .identity = "wdrtas"
+ .identity = "wdrtas",
};
switch (cmd) {
wdrtas_timer_keepalive();
wdrtas_timer_start();
}
+ /* not implemented. Done by H8
if (i & WDIOS_TEMPPANIC) {
- /* not implemented. Done by H8 */
- }
+ } */
return 0;
case WDIOC_KEEPALIVE:
*
* function called when watchdog device is opened
*/
-static int
-wdrtas_open(struct inode *inode, struct file *file)
+static int wdrtas_open(struct inode *inode, struct file *file)
{
/* only open once */
if (atomic_inc_return(&wdrtas_miscdev_open) > 1) {
*
* close function. Always succeeds
*/
-static int
-wdrtas_close(struct inode *inode, struct file *file)
+static int wdrtas_close(struct inode *inode, struct file *file)
{
/* only stop watchdog, if this was announced using 'V' before */
if (wdrtas_expect_close == WDRTAS_MAGIC_CHAR)
* wdrtas_temp_read gives the temperature to the users by copying this
* value as one byte into the user space buffer. The unit is Fahrenheit...
*/
-static ssize_t
-wdrtas_temp_read(struct file *file, char __user *buf,
+static ssize_t wdrtas_temp_read(struct file *file, char __user *buf,
size_t count, loff_t *ppos)
{
int temperature = 0;
*
* function called when temperature device is opened
*/
-static int
-wdrtas_temp_open(struct inode *inode, struct file *file)
+static int wdrtas_temp_open(struct inode *inode, struct file *file)
{
return nonseekable_open(inode, file);
}
*
* close function. Always succeeds
*/
-static int
-wdrtas_temp_close(struct inode *inode, struct file *file)
+static int wdrtas_temp_close(struct inode *inode, struct file *file)
{
return 0;
}
*
* wdrtas_reboot stops the watchdog in case of a reboot
*/
-static int
-wdrtas_reboot(struct notifier_block *this, unsigned long code, void *ptr)
+static int wdrtas_reboot(struct notifier_block *this,
+ unsigned long code, void *ptr)
{
- if ( (code==SYS_DOWN) || (code==SYS_HALT) )
+ if (code == SYS_DOWN || code == SYS_HALT)
wdrtas_timer_stop();
return NOTIFY_DONE;
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdrtas_write,
- .ioctl = wdrtas_ioctl,
+ .unlocked_ioctl = wdrtas_ioctl,
.open = wdrtas_open,
.release = wdrtas_close,
};
* this watchdog driver. It tolerates, if "get-sensor-state" and
* "ibm,get-system-parameter" are not available.
*/
-static int
-wdrtas_get_tokens(void)
+static int wdrtas_get_tokens(void)
{
wdrtas_token_get_sensor_state = rtas_token("get-sensor-state");
if (wdrtas_token_get_sensor_state == RTAS_UNKNOWN_SERVICE) {
* wdrtas_register_devs unregisters the watchdog and temperature watchdog
* misc devs
*/
-static void
-wdrtas_unregister_devs(void)
+static void wdrtas_unregister_devs(void)
{
misc_deregister(&wdrtas_miscdev);
if (wdrtas_token_get_sensor_state != RTAS_UNKNOWN_SERVICE)
* wdrtas_register_devs registers the watchdog and temperature watchdog
* misc devs
*/
-static int
-wdrtas_register_devs(void)
+static int wdrtas_register_devs(void)
{
int result;
*
* registers the file handlers and the reboot notifier
*/
-static int __init
-wdrtas_init(void)
+static int __init wdrtas_init(void)
{
if (wdrtas_get_tokens())
return -ENODEV;
*
* unregisters the file handlers and the reboot notifier
*/
-static void __exit
-wdrtas_exit(void)
+static void __exit wdrtas_exit(void)
{
if (!wdrtas_nowayout)
wdrtas_timer_stop();
* Matt Crocker).
* Alan Cox : Added wdt= boot option
* Alan Cox : Cleaned up copy/user stuff
- * Tim Hockin : Added insmod parameters, comment cleanup
- * Parameterized timeout
- * Tigran Aivazian : Restructured wdt_init() to handle failures
+ * Tim Hockin : Added insmod parameters, comment
+ * cleanup, parameterized timeout
+ * Tigran Aivazian : Restructured wdt_init() to handle
+ * failures
* Joel Becker : Added WDIOC_GET/SETTIMEOUT
* Matt Domsch : Added nowayout module option
*/
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#include "wd501p.h"
static int heartbeat = WD_TIMO;
static int wd_heartbeat;
module_param(heartbeat, int, 0);
-MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (0<heartbeat<65536, default=" __MODULE_STRING(WD_TIMO) ")");
+MODULE_PARM_DESC(heartbeat,
+ "Watchdog heartbeat in seconds. (0 < heartbeat < 65536, default="
+ __MODULE_STRING(WD_TIMO) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/* You must set these - there is no sane way to probe for this board. */
-static int io=0x240;
-static int irq=11;
+static int io = 0x240;
+static int irq = 11;
static DEFINE_SPINLOCK(wdt_lock);
static int tachometer;
module_param(tachometer, int, 0);
-MODULE_PARM_DESC(tachometer, "WDT501-P Fan Tachometer support (0=disable, default=0)");
+MODULE_PARM_DESC(tachometer,
+ "WDT501-P Fan Tachometer support (0=disable, default=0)");
#endif /* CONFIG_WDT_501 */
/*
static void wdt_ctr_mode(int ctr, int mode)
{
- ctr<<=6;
- ctr|=0x30;
- ctr|=(mode<<1);
+ ctr <<= 6;
+ ctr |= 0x30;
+ ctr |= (mode << 1);
outb_p(ctr, WDT_CR);
}
unsigned long flags;
spin_lock_irqsave(&wdt_lock, flags);
inb_p(WDT_DC); /* Disable watchdog */
- wdt_ctr_mode(0,3); /* Program CTR0 for Mode 3: Square Wave Generator */
- wdt_ctr_mode(1,2); /* Program CTR1 for Mode 2: Rate Generator */
- wdt_ctr_mode(2,0); /* Program CTR2 for Mode 0: Pulse on Terminal Count */
+ wdt_ctr_mode(0, 3); /* Program CTR0 for Mode 3:
+ Square Wave Generator */
+ wdt_ctr_mode(1, 2); /* Program CTR1 for Mode 2:
+ Rate Generator */
+ wdt_ctr_mode(2, 0); /* Program CTR2 for Mode 0:
+ Pulse on Terminal Count */
wdt_ctr_load(0, 8948); /* Count at 100Hz */
- wdt_ctr_load(1,wd_heartbeat); /* Heartbeat */
- wdt_ctr_load(2,65535); /* Length of reset pulse */
+ wdt_ctr_load(1, wd_heartbeat); /* Heartbeat */
+ wdt_ctr_load(2, 65535); /* Length of reset pulse */
outb_p(0, WDT_DC); /* Enable watchdog */
spin_unlock_irqrestore(&wdt_lock, flags);
return 0;
* Stop the watchdog driver.
*/
-static int wdt_stop (void)
+static int wdt_stop(void)
{
unsigned long flags;
spin_lock_irqsave(&wdt_lock, flags);
/* Turn the card off */
inb_p(WDT_DC); /* Disable watchdog */
- wdt_ctr_load(2,0); /* 0 length reset pulses now */
+ wdt_ctr_load(2, 0); /* 0 length reset pulses now */
spin_unlock_irqrestore(&wdt_lock, flags);
return 0;
}
/**
* wdt_ping:
*
- * Reload counter one with the watchdog heartbeat. We don't bother reloading
- * the cascade counter.
+ * Reload counter one with the watchdog heartbeat. We don't bother
+ * reloading the cascade counter.
*/
static int wdt_ping(void)
spin_lock_irqsave(&wdt_lock, flags);
/* Write a watchdog value */
inb_p(WDT_DC); /* Disable watchdog */
- wdt_ctr_mode(1,2); /* Re-Program CTR1 for Mode 2: Rate Generator */
- wdt_ctr_load(1,wd_heartbeat); /* Heartbeat */
+ wdt_ctr_mode(1, 2); /* Re-Program CTR1 for Mode 2:
+ Rate Generator */
+ wdt_ctr_load(1, wd_heartbeat); /* Heartbeat */
outb_p(0, WDT_DC); /* Enable watchdog */
spin_unlock_irqrestore(&wdt_lock, flags);
return 0;
* wdt_set_heartbeat:
* @t: the new heartbeat value that needs to be set.
*
- * Set a new heartbeat value for the watchdog device. If the heartbeat value is
- * incorrect we keep the old value and return -EINVAL. If successfull we
- * return 0.
+ * Set a new heartbeat value for the watchdog device. If the heartbeat
+ * value is incorrect we keep the old value and return -EINVAL. If
+ * successful we return 0.
*/
+
static int wdt_set_heartbeat(int t)
{
- if ((t < 1) || (t > 65535))
+ if (t < 1 || t > 65535)
return -EINVAL;
heartbeat = t;
new_status = inb_p(WDT_SR);
spin_unlock_irqrestore(&wdt_lock, flags);
- *status=0;
+ *status = 0;
if (new_status & WDC_SR_ISOI0)
*status |= WDIOF_EXTERN1;
if (new_status & WDC_SR_ISII1)
#ifdef CONFIG_WDT_501
if (!(status & WDC_SR_TGOOD))
- printk(KERN_CRIT "Overheat alarm.(%d)\n",inb_p(WDT_RT));
+ printk(KERN_CRIT "Overheat alarm.(%d)\n", inb_p(WDT_RT));
if (!(status & WDC_SR_PSUOVER))
printk(KERN_CRIT "PSU over voltage.\n");
if (!(status & WDC_SR_PSUUNDR))
* write of data will do, as we we don't define content meaning.
*/
-static ssize_t wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t wdt_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
- if(count) {
+ if (count) {
if (!nowayout) {
size_t i;
/**
* wdt_ioctl:
- * @inode: inode of the device
* @file: file handle to the device
* @cmd: watchdog command
* @arg: argument pointer
* querying capabilities and current status.
*/
-static int wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
{
void __user *argp = (void __user *)arg;
int __user *p = argp;
ident.options |= WDIOF_FANFAULT;
#endif /* CONFIG_WDT_501 */
- switch(cmd)
- {
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
-
- case WDIOC_GETSTATUS:
- wdt_get_status(&status);
- return put_user(status, p);
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdt_ping();
- return 0;
- case WDIOC_SETTIMEOUT:
- if (get_user(new_heartbeat, p))
- return -EFAULT;
-
- if (wdt_set_heartbeat(new_heartbeat))
- return -EINVAL;
-
- wdt_ping();
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ wdt_get_status(&status);
+ return put_user(status, p);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ wdt_ping();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
+ if (wdt_set_heartbeat(new_heartbeat))
+ return -EINVAL;
+ wdt_ping();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
+ default:
+ return -ENOTTY;
}
}
static int wdt_open(struct inode *inode, struct file *file)
{
- if(test_and_set_bit(0, &wdt_is_open))
+ if (test_and_set_bit(0, &wdt_is_open))
return -EBUSY;
/*
* Activate
wdt_stop();
clear_bit(0, &wdt_is_open);
} else {
- printk(KERN_CRIT "wdt: WDT device closed unexpectedly. WDT will not stop!\n");
+ printk(KERN_CRIT
+ "wdt: WDT device closed unexpectedly. WDT will not stop!\n");
wdt_ping();
}
expect_close = 0;
* farenheit. It was designed by an imperial measurement luddite.
*/
-static ssize_t wdt_temp_read(struct file *file, char __user *buf, size_t count, loff_t *ptr)
+static ssize_t wdt_temp_read(struct file *file, char __user *buf,
+ size_t count, loff_t *ptr)
{
int temperature;
if (wdt_get_temperature(&temperature))
return -EFAULT;
- if (copy_to_user (buf, &temperature, 1))
+ if (copy_to_user(buf, &temperature, 1))
return -EFAULT;
return 1;
static int wdt_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the card off */
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt_stop();
- }
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt_write,
- .ioctl = wdt_ioctl,
+ .unlocked_ioctl = wdt_ioctl,
.open = wdt_open,
.release = wdt_release,
};
#endif /* CONFIG_WDT_501 */
unregister_reboot_notifier(&wdt_notifier);
free_irq(irq, NULL);
- release_region(io,8);
+ release_region(io, 8);
}
/**
{
int ret;
- /* Check that the heartbeat value is within it's range ; if not reset to the default */
+ /* Check that the heartbeat value is within it's range;
+ if not reset to the default */
if (wdt_set_heartbeat(heartbeat)) {
wdt_set_heartbeat(WD_TIMO);
- printk(KERN_INFO "wdt: heartbeat value must be 0<heartbeat<65536, using %d\n",
+ printk(KERN_INFO "wdt: heartbeat value must be 0 < heartbeat < 65536, using %d\n",
WD_TIMO);
}
if (!request_region(io, 8, "wdt501p")) {
- printk(KERN_ERR "wdt: I/O address 0x%04x already in use\n", io);
+ printk(KERN_ERR
+ "wdt: I/O address 0x%04x already in use\n", io);
ret = -EBUSY;
goto out;
}
ret = request_irq(irq, wdt_interrupt, IRQF_DISABLED, "wdt501p", NULL);
- if(ret) {
+ if (ret) {
printk(KERN_ERR "wdt: IRQ %d is not free.\n", irq);
goto outreg;
}
ret = register_reboot_notifier(&wdt_notifier);
- if(ret) {
- printk(KERN_ERR "wdt: cannot register reboot notifier (err=%d)\n", ret);
+ if (ret) {
+ printk(KERN_ERR
+ "wdt: cannot register reboot notifier (err=%d)\n", ret);
goto outirq;
}
#ifdef CONFIG_WDT_501
ret = misc_register(&temp_miscdev);
if (ret) {
- printk(KERN_ERR "wdt: cannot register miscdev on minor=%d (err=%d)\n",
- TEMP_MINOR, ret);
+ printk(KERN_ERR
+ "wdt: cannot register miscdev on minor=%d (err=%d)\n",
+ TEMP_MINOR, ret);
goto outrbt;
}
#endif /* CONFIG_WDT_501 */
ret = misc_register(&wdt_miscdev);
if (ret) {
- printk(KERN_ERR "wdt: cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR
+ "wdt: cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto outmisc;
}
printk(KERN_INFO "WDT500/501-P driver 0.10 at 0x%04x (Interrupt %d). heartbeat=%d sec (nowayout=%d)\n",
io, irq, heartbeat, nowayout);
#ifdef CONFIG_WDT_501
- printk(KERN_INFO "wdt: Fan Tachometer is %s\n", (tachometer ? "Enabled" : "Disabled"));
+ printk(KERN_INFO "wdt: Fan Tachometer is %s\n",
+ (tachometer ? "Enabled" : "Disabled"));
#endif /* CONFIG_WDT_501 */
out:
outirq:
free_irq(irq, NULL);
outreg:
- release_region(io,8);
+ release_region(io, 8);
goto out;
}
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/interrupt.h>
+#include <linux/uaccess.h>
+#include <linux/irq.h>
+#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/uaccess.h>
-#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/hardware/dec21285.h>
return 0;
}
-static ssize_t
-watchdog_write(struct file *file, const char *data, size_t len, loff_t *ppos)
+static ssize_t watchdog_write(struct file *file, const char *data,
+ size_t len, loff_t *ppos)
{
/*
* Refresh the timer.
return len;
}
-static struct watchdog_info ident = {
+static const struct watchdog_info ident = {
.options = WDIOF_SETTIMEOUT,
.identity = "Footbridge Watchdog",
};
-static int
-watchdog_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long watchdog_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
unsigned int new_margin;
int ret = -ENOTTY;
- switch(cmd) {
+ switch (cmd) {
case WDIOC_GETSUPPORT:
ret = 0;
if (copy_to_user((void *)arg, &ident, sizeof(ident)))
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- ret = put_user(0,(int *)arg);
+ ret = put_user(0, (int *)arg);
break;
case WDIOC_KEEPALIVE:
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = watchdog_write,
- .ioctl = watchdog_ioctl,
+ .unlocked_ioctl = watchdog_ioctl,
.open = watchdog_open,
.release = watchdog_release,
};
if (retval < 0)
return retval;
- printk("Footbridge Watchdog Timer: 0.01, timer margin: %d sec\n",
- soft_margin);
+ printk(KERN_INFO
+ "Footbridge Watchdog Timer: 0.01, timer margin: %d sec\n",
+ soft_margin);
if (machine_is_cats())
- printk("Warning: Watchdog reset may not work on this machine.\n");
+ printk(KERN_WARN
+ "Warning: Watchdog reset may not work on this machine.\n");
return 0;
}
MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
module_param(soft_margin, int, 0);
-MODULE_PARM_DESC(soft_margin,"Watchdog timeout in seconds");
+MODULE_PARM_DESC(soft_margin, "Watchdog timeout in seconds");
module_init(footbridge_watchdog_init);
module_exit(footbridge_watchdog_exit);
* 07-Jul-2003 Daniele Bellucci: Audit return code of misc_register in
* nwwatchdog_init.
* 25-Oct-2005 Woody Suwalski: Convert addresses to #defs, add spinlocks
- * remove limitiation to be used on Netwinders only
+ * remove limitiation to be used on
+ * Netwinders only
*/
#include <linux/module.h>
#include <linux/watchdog.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
#include <asm/system.h>
#include <asm/mach-types.h>
-#include <asm/uaccess.h>
#define WATCHDOG_VERSION "0.04"
#define WATCHDOG_NAME "Wdt977"
#define DRIVER_VERSION WATCHDOG_NAME " driver, v" WATCHDOG_VERSION "\n"
#define IO_INDEX_PORT 0x370 /* on some systems it can be 0x3F0 */
-#define IO_DATA_PORT (IO_INDEX_PORT+1)
+#define IO_DATA_PORT (IO_INDEX_PORT + 1)
#define UNLOCK_DATA 0x87
#define LOCK_DATA 0xAA
static DEFINE_SPINLOCK(spinlock);
module_param(timeout, int, 0);
-MODULE_PARM_DESC(timeout,"Watchdog timeout in seconds (60..15300), default=" __MODULE_STRING(DEFAULT_TIMEOUT) ")");
+MODULE_PARM_DESC(timeout, "Watchdog timeout in seconds (60..15300), default="
+ __MODULE_STRING(DEFAULT_TIMEOUT) ")");
module_param(testmode, int, 0);
-MODULE_PARM_DESC(testmode,"Watchdog testmode (1 = no reboot), default=0");
+MODULE_PARM_DESC(testmode, "Watchdog testmode (1 = no reboot), default=0");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
/*
* Start the watchdog
outb_p(0xF2, IO_INDEX_PORT);
outb_p(timeoutM, IO_DATA_PORT);
outb_p(0xF3, IO_INDEX_PORT);
- outb_p(0x00, IO_DATA_PORT); /* another setting is 0E for kbd/mouse/LED */
+ outb_p(0x00, IO_DATA_PORT); /* another setting is 0E for
+ kbd/mouse/LED */
outb_p(0xF4, IO_INDEX_PORT);
outb_p(0x00, IO_DATA_PORT);
- /* at last select device Aux1 (dev=7) and set GP16 as a watchdog output */
- /* in test mode watch the bit 1 on F4 to indicate "triggered" */
- if (!testmode)
- {
+ /* At last select device Aux1 (dev=7) and set GP16 as a
+ * watchdog output. In test mode watch the bit 1 on F4 to
+ * indicate "triggered"
+ */
+ if (!testmode) {
outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
outb_p(0x07, IO_DATA_PORT);
outb_p(0xE6, IO_INDEX_PORT);
outb_p(0xF2, IO_INDEX_PORT);
outb_p(0x00, IO_DATA_PORT);
- /* at last select device Aux1 (dev=7) and set GP16 as a watchdog output */
+ /* at last select device Aux1 (dev=7) and set
+ GP16 as a watchdog output */
outb_p(DEVICE_REGISTER, IO_INDEX_PORT);
outb_p(0x07, IO_DATA_PORT);
outb_p(0xE6, IO_INDEX_PORT);
tmrval = (t + 59) / 60;
if (machine_is_netwinder()) {
- /* we have a hw bug somewhere, so each 977 minute is actually only 30sec
- * this limits the max timeout to half of device max of 255 minutes...
+ /* we have a hw bug somewhere, so each 977 minute is actually
+ * only 30sec. This limits the max timeout to half of device
+ * max of 255 minutes...
*/
tmrval += tmrval;
}
- if ((tmrval < 1) || (tmrval > 255))
+ if (tmrval < 1 || tmrval > 255)
return -EINVAL;
- /* timeout is the timeout in seconds, timeoutM is the timeout in minutes) */
+ /* timeout is the timeout in seconds, timeoutM is
+ the timeout in minutes) */
timeout = t;
timeoutM = tmrval;
return 0;
spin_unlock_irqrestore(&spinlock, flags);
- *status=0;
+ *status = 0;
if (new_status & 1)
*status |= WDIOF_CARDRESET;
static int wdt977_open(struct inode *inode, struct file *file)
{
/* If the watchdog is alive we don't need to start it again */
- if( test_and_set_bit(0,&timer_alive) )
+ if (test_and_set_bit(0, &timer_alive))
return -EBUSY;
if (nowayout)
* Shut off the timer.
* Lock it in if it's a module and we set nowayout
*/
- if (expect_close == 42)
- {
+ if (expect_close == 42) {
wdt977_stop();
- clear_bit(0,&timer_alive);
+ clear_bit(0, &timer_alive);
} else {
wdt977_keepalive();
- printk(KERN_CRIT PFX "Unexpected close, not stopping watchdog!\n");
+ printk(KERN_CRIT PFX
+ "Unexpected close, not stopping watchdog!\n");
}
expect_close = 0;
return 0;
static ssize_t wdt977_write(struct file *file, const char __user *buf,
size_t count, loff_t *ppos)
{
- if (count)
- {
- if (!nowayout)
- {
+ if (count) {
+ if (!nowayout) {
size_t i;
/* In case it was set long ago */
expect_close = 0;
- for (i = 0; i != count; i++)
- {
+ for (i = 0; i != count; i++) {
char c;
if (get_user(c, buf + i))
return -EFAULT;
return count;
}
+static const struct watchdog_info ident = {
+ .options = WDIOF_SETTIMEOUT |
+ WDIOF_MAGICCLOSE |
+ WDIOF_KEEPALIVEPING,
+ .firmware_version = 1,
+ .identity = WATCHDOG_NAME,
+};
+
/*
* wdt977_ioctl:
* @inode: inode of the device
* according to their available features.
*/
-static struct watchdog_info ident = {
- .options = WDIOF_SETTIMEOUT |
- WDIOF_MAGICCLOSE |
- WDIOF_KEEPALIVEPING,
- .firmware_version = 1,
- .identity = WATCHDOG_NAME,
-};
-
-static int wdt977_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
+static long wdt977_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int status;
int new_options, retval = -EINVAL;
uarg.i = (int __user *)arg;
- switch(cmd)
- {
- default:
- return -ENOTTY;
-
+ switch (cmd) {
case WDIOC_GETSUPPORT:
return copy_to_user(uarg.ident, &ident,
sizeof(ident)) ? -EFAULT : 0;
case WDIOC_GETBOOTSTATUS:
return put_user(0, uarg.i);
- case WDIOC_KEEPALIVE:
- wdt977_keepalive();
- return 0;
-
case WDIOC_SETOPTIONS:
- if (get_user (new_options, uarg.i))
+ if (get_user(new_options, uarg.i))
return -EFAULT;
if (new_options & WDIOS_DISABLECARD) {
return retval;
+ case WDIOC_KEEPALIVE:
+ wdt977_keepalive();
+ return 0;
+
case WDIOC_SETTIMEOUT:
if (get_user(new_timeout, uarg.i))
return -EFAULT;
case WDIOC_GETTIMEOUT:
return put_user(timeout, uarg.i);
+ default:
+ return -ENOTTY;
+
}
}
static int wdt977_notify_sys(struct notifier_block *this, unsigned long code,
void *unused)
{
- if(code==SYS_DOWN || code==SYS_HALT)
+ if (code == SYS_DOWN || code == SYS_HALT)
wdt977_stop();
return NOTIFY_DONE;
}
-static const struct file_operations wdt977_fops=
-{
+static const struct file_operations wdt977_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdt977_write,
- .ioctl = wdt977_ioctl,
+ .unlocked_ioctl = wdt977_ioctl,
.open = wdt977_open,
.release = wdt977_release,
};
-static struct miscdevice wdt977_miscdev=
-{
+static struct miscdevice wdt977_miscdev = {
.minor = WATCHDOG_MINOR,
.name = "watchdog",
.fops = &wdt977_fops,
{
int rc;
- //if (!machine_is_netwinder())
- // return -ENODEV;
-
printk(KERN_INFO PFX DRIVER_VERSION);
- /* Check that the timeout value is within it's range ; if not reset to the default */
- if (wdt977_set_timeout(timeout))
- {
+ /* Check that the timeout value is within its range;
+ if not reset to the default */
+ if (wdt977_set_timeout(timeout)) {
wdt977_set_timeout(DEFAULT_TIMEOUT);
- printk(KERN_INFO PFX "timeout value must be 60<timeout<15300, using %d\n",
- DEFAULT_TIMEOUT);
+ printk(KERN_INFO PFX
+ "timeout value must be 60 < timeout < 15300, using %d\n",
+ DEFAULT_TIMEOUT);
}
/* on Netwinder the IOports are already reserved by
* arch/arm/mach-footbridge/netwinder-hw.c
*/
- if (!machine_is_netwinder())
- {
- if (!request_region(IO_INDEX_PORT, 2, WATCHDOG_NAME))
- {
- printk(KERN_ERR PFX "I/O address 0x%04x already in use\n",
- IO_INDEX_PORT);
+ if (!machine_is_netwinder()) {
+ if (!request_region(IO_INDEX_PORT, 2, WATCHDOG_NAME)) {
+ printk(KERN_ERR PFX
+ "I/O address 0x%04x already in use\n",
+ IO_INDEX_PORT);
rc = -EIO;
goto err_out;
}
}
rc = register_reboot_notifier(&wdt977_notifier);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register reboot notifier (err=%d)\n",
- rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", rc);
goto err_out_region;
}
rc = misc_register(&wdt977_miscdev);
- if (rc)
- {
- printk(KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- wdt977_miscdev.minor, rc);
+ if (rc) {
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ wdt977_miscdev.minor, rc);
goto err_out_reboot;
}
- printk(KERN_INFO PFX "initialized. timeout=%d sec (nowayout=%d, testmode=%i)\n",
- timeout, nowayout, testmode);
+ printk(KERN_INFO PFX
+ "initialized. timeout=%d sec (nowayout=%d, testmode=%i)\n",
+ timeout, nowayout, testmode);
return 0;
unregister_reboot_notifier(&wdt977_notifier);
err_out_region:
if (!machine_is_netwinder())
- release_region(IO_INDEX_PORT,2);
+ release_region(IO_INDEX_PORT, 2);
err_out:
return rc;
}
wdt977_stop();
misc_deregister(&wdt977_miscdev);
unregister_reboot_notifier(&wdt977_notifier);
- release_region(IO_INDEX_PORT,2);
+ release_region(IO_INDEX_PORT, 2);
}
module_init(wd977_init);
* JP Nollmann : Added support for PCI wdt501p
* Alan Cox : Split ISA and PCI cards into two drivers
* Jeff Garzik : PCI cleanups
- * Tigran Aivazian : Restructured wdtpci_init_one() to handle failures
+ * Tigran Aivazian : Restructured wdtpci_init_one() to handle
+ * failures
* Joel Becker : Added WDIOC_GET/SETTIMEOUT
- * Zwane Mwaikambo : Magic char closing, locking changes, cleanups
+ * Zwane Mwaikambo : Magic char closing, locking changes,
+ * cleanups
* Matt Domsch : nowayout module option
*/
#include <linux/miscdevice.h>
#include <linux/watchdog.h>
#include <linux/ioport.h>
+#include <linux/delay.h>
#include <linux/notifier.h>
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
#include <asm/system.h>
#define WDT_IS_PCI
/* We can only use 1 card due to the /dev/watchdog restriction */
static int dev_count;
-static struct semaphore open_sem;
+static unsigned long open_lock;
static DEFINE_SPINLOCK(wdtpci_lock);
static char expect_close;
static int heartbeat = WD_TIMO;
static int wd_heartbeat;
module_param(heartbeat, int, 0);
-MODULE_PARM_DESC(heartbeat, "Watchdog heartbeat in seconds. (0<heartbeat<65536, default=" __MODULE_STRING(WD_TIMO) ")");
+MODULE_PARM_DESC(heartbeat,
+ "Watchdog heartbeat in seconds. (0<heartbeat<65536, default="
+ __MODULE_STRING(WD_TIMO) ")");
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
-MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+MODULE_PARM_DESC(nowayout,
+ "Watchdog cannot be stopped once started (default="
+ __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
#ifdef CONFIG_WDT_501_PCI
/* Support for the Fan Tachometer on the PCI-WDT501 */
static int tachometer;
module_param(tachometer, int, 0);
-MODULE_PARM_DESC(tachometer, "PCI-WDT501 Fan Tachometer support (0=disable, default=0)");
+MODULE_PARM_DESC(tachometer,
+ "PCI-WDT501 Fan Tachometer support (0=disable, default=0)");
#endif /* CONFIG_WDT_501_PCI */
/*
static void wdtpci_ctr_mode(int ctr, int mode)
{
- ctr<<=6;
- ctr|=0x30;
- ctr|=(mode<<1);
- outb_p(ctr, WDT_CR);
+ ctr <<= 6;
+ ctr |= 0x30;
+ ctr |= (mode << 1);
+ outb(ctr, WDT_CR);
+ udelay(8);
}
static void wdtpci_ctr_load(int ctr, int val)
{
- outb_p(val&0xFF, WDT_COUNT0+ctr);
- outb_p(val>>8, WDT_COUNT0+ctr);
+ outb(val & 0xFF, WDT_COUNT0 + ctr);
+ udelay(8);
+ outb(val >> 8, WDT_COUNT0 + ctr);
+ udelay(8);
}
/**
* "pet" the watchdog, as Access says.
* This resets the clock outputs.
*/
- inb_p(WDT_DC); /* Disable watchdog */
- wdtpci_ctr_mode(2,0); /* Program CTR2 for Mode 0: Pulse on Terminal Count */
- outb_p(0, WDT_DC); /* Enable watchdog */
-
- inb_p(WDT_DC); /* Disable watchdog */
- outb_p(0, WDT_CLOCK); /* 2.0833MHz clock */
- inb_p(WDT_BUZZER); /* disable */
- inb_p(WDT_OPTONOTRST); /* disable */
- inb_p(WDT_OPTORST); /* disable */
- inb_p(WDT_PROGOUT); /* disable */
- wdtpci_ctr_mode(0,3); /* Program CTR0 for Mode 3: Square Wave Generator */
- wdtpci_ctr_mode(1,2); /* Program CTR1 for Mode 2: Rate Generator */
- wdtpci_ctr_mode(2,1); /* Program CTR2 for Mode 1: Retriggerable One-Shot */
- wdtpci_ctr_load(0,20833); /* count at 100Hz */
- wdtpci_ctr_load(1,wd_heartbeat);/* Heartbeat */
+ inb(WDT_DC); /* Disable watchdog */
+ udelay(8);
+ wdtpci_ctr_mode(2, 0); /* Program CTR2 for Mode 0:
+ Pulse on Terminal Count */
+ outb(0, WDT_DC); /* Enable watchdog */
+ udelay(8);
+ inb(WDT_DC); /* Disable watchdog */
+ udelay(8);
+ outb(0, WDT_CLOCK); /* 2.0833MHz clock */
+ udelay(8);
+ inb(WDT_BUZZER); /* disable */
+ udelay(8);
+ inb(WDT_OPTONOTRST); /* disable */
+ udelay(8);
+ inb(WDT_OPTORST); /* disable */
+ udelay(8);
+ inb(WDT_PROGOUT); /* disable */
+ udelay(8);
+ wdtpci_ctr_mode(0, 3); /* Program CTR0 for Mode 3:
+ Square Wave Generator */
+ wdtpci_ctr_mode(1, 2); /* Program CTR1 for Mode 2:
+ Rate Generator */
+ wdtpci_ctr_mode(2, 1); /* Program CTR2 for Mode 1:
+ Retriggerable One-Shot */
+ wdtpci_ctr_load(0, 20833); /* count at 100Hz */
+ wdtpci_ctr_load(1, wd_heartbeat);/* Heartbeat */
/* DO NOT LOAD CTR2 on PCI card! -- JPN */
- outb_p(0, WDT_DC); /* Enable watchdog */
+ outb(0, WDT_DC); /* Enable watchdog */
+ udelay(8);
spin_unlock_irqrestore(&wdtpci_lock, flags);
return 0;
* Stop the watchdog driver.
*/
-static int wdtpci_stop (void)
+static int wdtpci_stop(void)
{
unsigned long flags;
/* Turn the card off */
spin_lock_irqsave(&wdtpci_lock, flags);
- inb_p(WDT_DC); /* Disable watchdog */
- wdtpci_ctr_load(2,0); /* 0 length reset pulses now */
+ inb(WDT_DC); /* Disable watchdog */
+ udelay(8);
+ wdtpci_ctr_load(2, 0); /* 0 length reset pulses now */
spin_unlock_irqrestore(&wdtpci_lock, flags);
return 0;
}
/**
* wdtpci_ping:
*
- * Reload counter one with the watchdog heartbeat. We don't bother reloading
- * the cascade counter.
+ * Reload counter one with the watchdog heartbeat. We don't bother
+ * reloading the cascade counter.
*/
static int wdtpci_ping(void)
{
unsigned long flags;
- /* Write a watchdog value */
spin_lock_irqsave(&wdtpci_lock, flags);
- inb_p(WDT_DC); /* Disable watchdog */
- wdtpci_ctr_mode(1,2); /* Re-Program CTR1 for Mode 2: Rate Generator */
- wdtpci_ctr_load(1,wd_heartbeat);/* Heartbeat */
- outb_p(0, WDT_DC); /* Enable watchdog */
+ /* Write a watchdog value */
+ inb(WDT_DC); /* Disable watchdog */
+ udelay(8);
+ wdtpci_ctr_mode(1, 2); /* Re-Program CTR1 for Mode 2:
+ Rate Generator */
+ wdtpci_ctr_load(1, wd_heartbeat);/* Heartbeat */
+ outb(0, WDT_DC); /* Enable watchdog */
+ udelay(8);
spin_unlock_irqrestore(&wdtpci_lock, flags);
return 0;
}
* wdtpci_set_heartbeat:
* @t: the new heartbeat value that needs to be set.
*
- * Set a new heartbeat value for the watchdog device. If the heartbeat value is
- * incorrect we keep the old value and return -EINVAL. If successfull we
- * return 0.
+ * Set a new heartbeat value for the watchdog device. If the heartbeat
+ * value is incorrect we keep the old value and return -EINVAL.
+ * If successful we return 0.
*/
static int wdtpci_set_heartbeat(int t)
{
/* Arbitrary, can't find the card's limits */
- if ((t < 1) || (t > 65535))
+ if (t < 1 || t > 65535)
return -EINVAL;
heartbeat = t;
static int wdtpci_get_status(int *status)
{
- unsigned char new_status=inb_p(WDT_SR);
+ unsigned char new_status;
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdtpci_lock, flags);
+ new_status = inb(WDT_SR);
+ spin_unlock_irqrestore(&wdtpci_lock, flags);
- *status=0;
+ *status = 0;
if (new_status & WDC_SR_ISOI0)
*status |= WDIOF_EXTERN1;
if (new_status & WDC_SR_ISII1)
static int wdtpci_get_temperature(int *temperature)
{
- unsigned short c=inb_p(WDT_RT);
-
+ unsigned short c;
+ unsigned long flags;
+ spin_lock_irqsave(&wdtpci_lock, flags);
+ c = inb(WDT_RT);
+ udelay(8);
+ spin_unlock_irqrestore(&wdtpci_lock, flags);
*temperature = (c * 11 / 15) + 7;
return 0;
}
* Read the status register see what is up and
* then printk it.
*/
- unsigned char status=inb_p(WDT_SR);
+ unsigned char status;
+
+ spin_lock(&wdtpci_lock);
+
+ status = inb(WDT_SR);
+ udelay(8);
printk(KERN_CRIT PFX "status %d\n", status);
#ifdef CONFIG_WDT_501_PCI
- if (!(status & WDC_SR_TGOOD))
- printk(KERN_CRIT PFX "Overheat alarm.(%d)\n",inb_p(WDT_RT));
+ if (!(status & WDC_SR_TGOOD)) {
+ u8 alarm = inb(WDT_RT);
+ printk(KERN_CRIT PFX "Overheat alarm.(%d)\n", alarm);
+ udelay(8);
+ }
if (!(status & WDC_SR_PSUOVER))
- printk(KERN_CRIT PFX "PSU over voltage.\n");
+ printk(KERN_CRIT PFX "PSU over voltage.\n");
if (!(status & WDC_SR_PSUUNDR))
- printk(KERN_CRIT PFX "PSU under voltage.\n");
+ printk(KERN_CRIT PFX "PSU under voltage.\n");
if (tachometer) {
if (!(status & WDC_SR_FANGOOD))
printk(KERN_CRIT PFX "Possible fan fault.\n");
printk(KERN_CRIT PFX "Reset in 5ms.\n");
#endif
}
+ spin_unlock(&wdtpci_lock);
return IRQ_HANDLED;
}
* write of data will do, as we we don't define content meaning.
*/
-static ssize_t wdtpci_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
+static ssize_t wdtpci_write(struct file *file, const char __user *buf,
+ size_t count, loff_t *ppos)
{
if (count) {
if (!nowayout) {
for (i = 0; i != count; i++) {
char c;
- if(get_user(c, buf+i))
+ if (get_user(c, buf + i))
return -EFAULT;
if (c == 'V')
expect_close = 42;
}
wdtpci_ping();
}
-
return count;
}
/**
* wdtpci_ioctl:
- * @inode: inode of the device
* @file: file handle to the device
* @cmd: watchdog command
* @arg: argument pointer
* querying capabilities and current status.
*/
-static int wdtpci_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
- unsigned long arg)
+static long wdtpci_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
{
int new_heartbeat;
int status;
ident.options |= WDIOF_FANFAULT;
#endif /* CONFIG_WDT_501_PCI */
- switch(cmd)
- {
- default:
- return -ENOTTY;
- case WDIOC_GETSUPPORT:
- return copy_to_user(argp, &ident, sizeof(ident))?-EFAULT:0;
-
- case WDIOC_GETSTATUS:
- wdtpci_get_status(&status);
- return put_user(status, p);
- case WDIOC_GETBOOTSTATUS:
- return put_user(0, p);
- case WDIOC_KEEPALIVE:
- wdtpci_ping();
- return 0;
- case WDIOC_SETTIMEOUT:
- if (get_user(new_heartbeat, p))
- return -EFAULT;
-
- if (wdtpci_set_heartbeat(new_heartbeat))
- return -EINVAL;
-
- wdtpci_ping();
- /* Fall */
- case WDIOC_GETTIMEOUT:
- return put_user(heartbeat, p);
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ return copy_to_user(argp, &ident, sizeof(ident)) ? -EFAULT : 0;
+ case WDIOC_GETSTATUS:
+ wdtpci_get_status(&status);
+ return put_user(status, p);
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+ case WDIOC_KEEPALIVE:
+ wdtpci_ping();
+ return 0;
+ case WDIOC_SETTIMEOUT:
+ if (get_user(new_heartbeat, p))
+ return -EFAULT;
+ if (wdtpci_set_heartbeat(new_heartbeat))
+ return -EINVAL;
+ wdtpci_ping();
+ /* Fall */
+ case WDIOC_GETTIMEOUT:
+ return put_user(heartbeat, p);
+ default:
+ return -ENOTTY;
}
}
static int wdtpci_open(struct inode *inode, struct file *file)
{
- if (down_trylock(&open_sem))
+ if (test_and_set_bit(0, &open_lock))
return -EBUSY;
- if (nowayout) {
+ if (nowayout)
__module_get(THIS_MODULE);
- }
/*
* Activate
*/
wdtpci_ping();
}
expect_close = 0;
- up(&open_sem);
+ clear_bit(0, &open_lock);
return 0;
}
* fahrenheit. It was designed by an imperial measurement luddite.
*/
-static ssize_t wdtpci_temp_read(struct file *file, char __user *buf, size_t count, loff_t *ptr)
+static ssize_t wdtpci_temp_read(struct file *file, char __user *buf,
+ size_t count, loff_t *ptr)
{
int temperature;
if (wdtpci_get_temperature(&temperature))
return -EFAULT;
- if (copy_to_user (buf, &temperature, 1))
+ if (copy_to_user(buf, &temperature, 1))
return -EFAULT;
return 1;
*/
static int wdtpci_notify_sys(struct notifier_block *this, unsigned long code,
- void *unused)
+ void *unused)
{
- if (code==SYS_DOWN || code==SYS_HALT) {
- /* Turn the card off */
+ if (code == SYS_DOWN || code == SYS_HALT)
wdtpci_stop();
- }
return NOTIFY_DONE;
}
.owner = THIS_MODULE,
.llseek = no_llseek,
.write = wdtpci_write,
- .ioctl = wdtpci_ioctl,
+ .unlocked_ioctl = wdtpci_ioctl,
.open = wdtpci_open,
.release = wdtpci_release,
};
};
-static int __devinit wdtpci_init_one (struct pci_dev *dev,
- const struct pci_device_id *ent)
+static int __devinit wdtpci_init_one(struct pci_dev *dev,
+ const struct pci_device_id *ent)
{
int ret = -EIO;
dev_count++;
if (dev_count > 1) {
- printk (KERN_ERR PFX "this driver only supports 1 device\n");
+ printk(KERN_ERR PFX "This driver only supports one device\n");
return -ENODEV;
}
- if (pci_enable_device (dev)) {
- printk (KERN_ERR PFX "Not possible to enable PCI Device\n");
+ if (pci_enable_device(dev)) {
+ printk(KERN_ERR PFX "Not possible to enable PCI Device\n");
return -ENODEV;
}
- if (pci_resource_start (dev, 2) == 0x0000) {
- printk (KERN_ERR PFX "No I/O-Address for card detected\n");
+ if (pci_resource_start(dev, 2) == 0x0000) {
+ printk(KERN_ERR PFX "No I/O-Address for card detected\n");
ret = -ENODEV;
goto out_pci;
}
- sema_init(&open_sem, 1);
-
irq = dev->irq;
- io = pci_resource_start (dev, 2);
+ io = pci_resource_start(dev, 2);
- if (request_region (io, 16, "wdt_pci") == NULL) {
- printk (KERN_ERR PFX "I/O address 0x%04x already in use\n", io);
+ if (request_region(io, 16, "wdt_pci") == NULL) {
+ printk(KERN_ERR PFX "I/O address 0x%04x already in use\n", io);
goto out_pci;
}
- if (request_irq (irq, wdtpci_interrupt, IRQF_DISABLED | IRQF_SHARED,
+ if (request_irq(irq, wdtpci_interrupt, IRQF_DISABLED | IRQF_SHARED,
"wdt_pci", &wdtpci_miscdev)) {
- printk (KERN_ERR PFX "IRQ %d is not free\n", irq);
+ printk(KERN_ERR PFX "IRQ %d is not free\n", irq);
goto out_reg;
}
- printk ("PCI-WDT500/501 (PCI-WDG-CSM) driver 0.10 at 0x%04x (Interrupt %d)\n",
- io, irq);
+ printk(KERN_INFO
+ "PCI-WDT500/501 (PCI-WDG-CSM) driver 0.10 at 0x%04x (Interrupt %d)\n",
+ io, irq);
- /* Check that the heartbeat value is within it's range ; if not reset to the default */
+ /* Check that the heartbeat value is within its range;
+ if not reset to the default */
if (wdtpci_set_heartbeat(heartbeat)) {
wdtpci_set_heartbeat(WD_TIMO);
- printk(KERN_INFO PFX "heartbeat value must be 0<heartbeat<65536, using %d\n",
- WD_TIMO);
+ printk(KERN_INFO PFX
+ "heartbeat value must be 0 < heartbeat < 65536, using %d\n",
+ WD_TIMO);
}
- ret = register_reboot_notifier (&wdtpci_notifier);
+ ret = register_reboot_notifier(&wdtpci_notifier);
if (ret) {
- printk (KERN_ERR PFX "cannot register reboot notifier (err=%d)\n", ret);
+ printk(KERN_ERR PFX
+ "cannot register reboot notifier (err=%d)\n", ret);
goto out_irq;
}
#ifdef CONFIG_WDT_501_PCI
- ret = misc_register (&temp_miscdev);
+ ret = misc_register(&temp_miscdev);
if (ret) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- TEMP_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ TEMP_MINOR, ret);
goto out_rbt;
}
#endif /* CONFIG_WDT_501_PCI */
- ret = misc_register (&wdtpci_miscdev);
+ ret = misc_register(&wdtpci_miscdev);
if (ret) {
- printk (KERN_ERR PFX "cannot register miscdev on minor=%d (err=%d)\n",
- WATCHDOG_MINOR, ret);
+ printk(KERN_ERR PFX
+ "cannot register miscdev on minor=%d (err=%d)\n",
+ WATCHDOG_MINOR, ret);
goto out_misc;
}
printk(KERN_INFO PFX "initialized. heartbeat=%d sec (nowayout=%d)\n",
heartbeat, nowayout);
#ifdef CONFIG_WDT_501_PCI
- printk(KERN_INFO "wdt: Fan Tachometer is %s\n", (tachometer ? "Enabled" : "Disabled"));
+ printk(KERN_INFO "wdt: Fan Tachometer is %s\n",
+ (tachometer ? "Enabled" : "Disabled"));
#endif /* CONFIG_WDT_501_PCI */
ret = 0;
out_irq:
free_irq(irq, &wdtpci_miscdev);
out_reg:
- release_region (io, 16);
+ release_region(io, 16);
out_pci:
pci_disable_device(dev);
goto out;
}
-static void __devexit wdtpci_remove_one (struct pci_dev *pdev)
+static void __devexit wdtpci_remove_one(struct pci_dev *pdev)
{
/* here we assume only one device will ever have
* been picked up and registered by probe function */
static void __exit wdtpci_cleanup(void)
{
- pci_unregister_driver (&wdtpci_driver);
+ pci_unregister_driver(&wdtpci_driver);
}
static int __init wdtpci_init(void)
{
- return pci_register_driver (&wdtpci_driver);
+ return pci_register_driver(&wdtpci_driver);
}
static int output_records(int outfd)
{
- unsigned char zeroes[5] = {0, 0, 0, 0, 0};
+ unsigned char zeroes[6] = {0, 0, 0, 0, 0, 0};
struct ihex_binrec *p = records;
while (p) {
uint16_t writelen = (p->len + 9) & ~3;
p->addr = htonl(p->addr);
- p->len = htonl(p->len);
+ p->len = htons(p->len);
write(outfd, &p->addr, writelen);
p = p->next;
}
/* EOF record is zero length, since we don't bother to represent
the type field in the binary version */
- write(outfd, zeroes, 5);
+ write(outfd, zeroes, 6);
return 0;
}
}
mntget(newmnt);
- err = do_add_mount(newmnt, nd, MNT_SHRINKABLE, &afs_vfsmounts);
+ err = do_add_mount(newmnt, &nd->path, MNT_SHRINKABLE, &afs_vfsmounts);
switch (err) {
case 0:
path_put(&nd->path);
page = pages[loop];
if (page->index > wb->last)
break;
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
break;
if (!PageDirty(page) ||
page_private(page) != (unsigned long) wb) {
*/
bvl = mempool_alloc(bs->bvec_pools[*idx], gfp_mask);
- if (bvl) {
- struct biovec_slab *bp = bvec_slabs + *idx;
-
- memset(bvl, 0, bp->nr_vecs * sizeof(struct bio_vec));
- }
+ if (bvl)
+ memset(bvl, 0, bvec_nr_vecs(*idx) * sizeof(struct bio_vec));
return bvl;
}
goto out;
}
bio->bi_flags |= idx << BIO_POOL_OFFSET;
- bio->bi_max_vecs = bvec_slabs[idx].nr_vecs;
+ bio->bi_max_vecs = bvec_nr_vecs(idx);
}
bio->bi_io_vec = bvl;
}
* hooks: /n/, see "layering violations".
*/
ret = devcgroup_inode_permission(bdev->bd_inode, perm);
- if (ret != 0)
+ if (ret != 0) {
+ bdput(bdev);
return ret;
+ }
ret = -ENXIO;
file->f_mapping = bdev->bd_inode->i_mapping;
bdev = ERR_PTR(error);
goto out;
}
+EXPORT_SYMBOL(lookup_bdev);
/**
* open_bdev_excl - open a block device by name and set it up for use
/*
* The buffer's backing address_space's private_lock must be held
*/
-static inline void __remove_assoc_queue(struct buffer_head *bh)
+static void __remove_assoc_queue(struct buffer_head *bh)
{
list_del_init(&bh->b_assoc_buffers);
WARN_ON(!bh->b_assoc_map);
*/
if (wbc->sync_mode != WB_SYNC_NONE || !wbc->nonblocking) {
lock_buffer(bh);
- } else if (test_set_buffer_locked(bh)) {
+ } else if (!trylock_buffer(bh)) {
redirty_page_for_writepage(wbc, page);
continue;
}
if (rw == SWRITE || rw == SWRITE_SYNC)
lock_buffer(bh);
- else if (test_set_buffer_locked(bh))
+ else if (!trylock_buffer(bh))
continue;
if (rw == WRITE || rw == SWRITE || rw == SWRITE_SYNC) {
int err;
mntget(newmnt);
- err = do_add_mount(newmnt, nd, nd->path.mnt->mnt_flags, mntlist);
+ err = do_add_mount(newmnt, &nd->path, nd->path.mnt->mnt_flags, mntlist);
switch (err) {
case 0:
path_put(&nd->path);
if (first < 0)
lock_page(page);
- else if (TestSetPageLocked(page))
+ else if (!trylock_page(page))
break;
if (unlikely(page->mapping != mapping)) {
#define CONFIGFS_USET_DEFAULT 0x0080
#define CONFIGFS_USET_DROPPING 0x0100
#define CONFIGFS_USET_IN_MKDIR 0x0200
+#define CONFIGFS_USET_CREATING 0x0400
#define CONFIGFS_NOT_PINNED (CONFIGFS_ITEM_ATTR)
+extern struct mutex configfs_symlink_mutex;
extern spinlock_t configfs_dirent_lock;
extern struct vfsmount * configfs_mount;
extern int configfs_create_file(struct config_item *, const struct configfs_attribute *);
extern int configfs_make_dirent(struct configfs_dirent *,
struct dentry *, void *, umode_t, int);
+extern int configfs_dirent_is_ready(struct configfs_dirent *);
extern int configfs_add_file(struct dentry *, const struct configfs_attribute *, int);
extern void configfs_hash_and_remove(struct dentry * dir, const char * name);
error = configfs_dirent_exists(p->d_fsdata, d->d_name.name);
if (!error)
error = configfs_make_dirent(p->d_fsdata, d, k, mode,
- CONFIGFS_DIR);
+ CONFIGFS_DIR | CONFIGFS_USET_CREATING);
if (!error) {
error = configfs_create(d, mode, init_dir);
if (!error) {
* configfs_create_dir - create a directory for an config_item.
* @item: config_itemwe're creating directory for.
* @dentry: config_item's dentry.
+ *
+ * Note: user-created entries won't be allowed under this new directory
+ * until it is validated by configfs_dir_set_ready()
*/
static int configfs_create_dir(struct config_item * item, struct dentry *dentry)
return error;
}
+/*
+ * Allow userspace to create new entries under a new directory created with
+ * configfs_create_dir(), and under all of its chidlren directories recursively.
+ * @sd configfs_dirent of the new directory to validate
+ *
+ * Caller must hold configfs_dirent_lock.
+ */
+static void configfs_dir_set_ready(struct configfs_dirent *sd)
+{
+ struct configfs_dirent *child_sd;
+
+ sd->s_type &= ~CONFIGFS_USET_CREATING;
+ list_for_each_entry(child_sd, &sd->s_children, s_sibling)
+ if (child_sd->s_type & CONFIGFS_USET_CREATING)
+ configfs_dir_set_ready(child_sd);
+}
+
+/*
+ * Check that a directory does not belong to a directory hierarchy being
+ * attached and not validated yet.
+ * @sd configfs_dirent of the directory to check
+ *
+ * @return non-zero iff the directory was validated
+ *
+ * Note: takes configfs_dirent_lock, so the result may change from false to true
+ * in two consecutive calls, but never from true to false.
+ */
+int configfs_dirent_is_ready(struct configfs_dirent *sd)
+{
+ int ret;
+
+ spin_lock(&configfs_dirent_lock);
+ ret = !(sd->s_type & CONFIGFS_USET_CREATING);
+ spin_unlock(&configfs_dirent_lock);
+
+ return ret;
+}
+
int configfs_create_link(struct configfs_symlink *sl,
struct dentry *parent,
struct dentry *dentry)
* The only thing special about this is that we remove any files in
* the directory before we remove the directory, and we've inlined
* what used to be configfs_rmdir() below, instead of calling separately.
+ *
+ * Caller holds the mutex of the item's inode
*/
static void configfs_remove_dir(struct config_item * item)
struct configfs_dirent * parent_sd = dentry->d_parent->d_fsdata;
struct configfs_dirent * sd;
int found = 0;
- int err = 0;
+ int err;
+
+ /*
+ * Fake invisibility if dir belongs to a group/default groups hierarchy
+ * being attached
+ *
+ * This forbids userspace to read/write attributes of items which may
+ * not complete their initialization, since the dentries of the
+ * attributes won't be instantiated.
+ */
+ err = -ENOENT;
+ if (!configfs_dirent_is_ready(parent_sd))
+ goto out;
list_for_each_entry(sd, &parent_sd->s_children, s_sibling) {
if (sd->s_type & CONFIGFS_NOT_PINNED) {
return simple_lookup(dir, dentry, nd);
}
+out:
return ERR_PTR(err);
}
struct configfs_dirent *sd;
int ret;
+ /* Mark that we're trying to drop the group */
+ parent_sd->s_type |= CONFIGFS_USET_DROPPING;
+
ret = -EBUSY;
if (!list_empty(&parent_sd->s_links))
goto out;
ret = 0;
list_for_each_entry(sd, &parent_sd->s_children, s_sibling) {
- if (sd->s_type & CONFIGFS_NOT_PINNED)
+ if (!sd->s_element ||
+ (sd->s_type & CONFIGFS_NOT_PINNED))
continue;
if (sd->s_type & CONFIGFS_USET_DEFAULT) {
/* Abort if racing with mkdir() */
*wait_mutex = &sd->s_dentry->d_inode->i_mutex;
return -EAGAIN;
}
- /* Mark that we're trying to drop the group */
- sd->s_type |= CONFIGFS_USET_DROPPING;
/*
* Yup, recursive. If there's a problem, blame
struct configfs_dirent *parent_sd = dentry->d_fsdata;
struct configfs_dirent *sd;
- list_for_each_entry(sd, &parent_sd->s_children, s_sibling) {
- if (sd->s_type & CONFIGFS_USET_DEFAULT) {
+ parent_sd->s_type &= ~CONFIGFS_USET_DROPPING;
+
+ list_for_each_entry(sd, &parent_sd->s_children, s_sibling)
+ if (sd->s_type & CONFIGFS_USET_DEFAULT)
configfs_detach_rollback(sd->s_dentry);
- sd->s_type &= ~CONFIGFS_USET_DROPPING;
- }
- }
}
static void detach_attrs(struct config_item * item)
static int populate_groups(struct config_group *group)
{
struct config_group *new_group;
- struct dentry *dentry = group->cg_item.ci_dentry;
int ret = 0;
int i;
if (group->default_groups) {
- /*
- * FYI, we're faking mkdir here
- * I'm not sure we need this semaphore, as we're called
- * from our parent's mkdir. That holds our parent's
- * i_mutex, so afaik lookup cannot continue through our
- * parent to find us, let alone mess with our tree.
- * That said, taking our i_mutex is closer to mkdir
- * emulation, and shouldn't hurt.
- */
- mutex_lock_nested(&dentry->d_inode->i_mutex, I_MUTEX_CHILD);
-
for (i = 0; group->default_groups[i]; i++) {
new_group = group->default_groups[i];
ret = create_default_group(group, new_group);
- if (ret)
+ if (ret) {
+ detach_groups(group);
break;
+ }
}
-
- mutex_unlock(&dentry->d_inode->i_mutex);
}
- if (ret)
- detach_groups(group);
-
return ret;
}
if (!ret) {
ret = populate_attrs(item);
if (ret) {
+ /*
+ * We are going to remove an inode and its dentry but
+ * the VFS may already have hit and used them. Thus,
+ * we must lock them as rmdir() would.
+ */
+ mutex_lock(&dentry->d_inode->i_mutex);
configfs_remove_dir(item);
+ dentry->d_inode->i_flags |= S_DEAD;
+ mutex_unlock(&dentry->d_inode->i_mutex);
d_delete(dentry);
}
}
return ret;
}
+/* Caller holds the mutex of the item's inode */
static void configfs_detach_item(struct config_item *item)
{
detach_attrs(item);
sd = dentry->d_fsdata;
sd->s_type |= CONFIGFS_USET_DIR;
+ /*
+ * FYI, we're faking mkdir in populate_groups()
+ * We must lock the group's inode to avoid races with the VFS
+ * which can already hit the inode and try to add/remove entries
+ * under it.
+ *
+ * We must also lock the inode to remove it safely in case of
+ * error, as rmdir() would.
+ */
+ mutex_lock_nested(&dentry->d_inode->i_mutex, I_MUTEX_CHILD);
ret = populate_groups(to_config_group(item));
if (ret) {
configfs_detach_item(item);
- d_delete(dentry);
+ dentry->d_inode->i_flags |= S_DEAD;
}
+ mutex_unlock(&dentry->d_inode->i_mutex);
+ if (ret)
+ d_delete(dentry);
}
return ret;
}
+/* Caller holds the mutex of the group's inode */
static void configfs_detach_group(struct config_item *item)
{
detach_groups(to_config_group(item));
struct configfs_subsystem *subsys;
struct configfs_dirent *sd;
struct config_item_type *type;
- struct module *owner = NULL;
+ struct module *subsys_owner = NULL, *new_item_owner = NULL;
char *name;
if (dentry->d_parent == configfs_sb->s_root) {
}
sd = dentry->d_parent->d_fsdata;
+
+ /*
+ * Fake invisibility if dir belongs to a group/default groups hierarchy
+ * being attached
+ */
+ if (!configfs_dirent_is_ready(sd)) {
+ ret = -ENOENT;
+ goto out;
+ }
+
if (!(sd->s_type & CONFIGFS_USET_DIR)) {
ret = -EPERM;
goto out;
goto out_put;
}
+ /*
+ * The subsystem may belong to a different module than the item
+ * being created. We don't want to safely pin the new item but
+ * fail to pin the subsystem it sits under.
+ */
+ if (!subsys->su_group.cg_item.ci_type) {
+ ret = -EINVAL;
+ goto out_put;
+ }
+ subsys_owner = subsys->su_group.cg_item.ci_type->ct_owner;
+ if (!try_module_get(subsys_owner)) {
+ ret = -EINVAL;
+ goto out_put;
+ }
+
name = kmalloc(dentry->d_name.len + 1, GFP_KERNEL);
if (!name) {
ret = -ENOMEM;
- goto out_put;
+ goto out_subsys_put;
}
snprintf(name, dentry->d_name.len + 1, "%s", dentry->d_name.name);
kfree(name);
if (ret) {
/*
- * If item == NULL, then link_obj() was never called.
+ * If ret != 0, then link_obj() was never called.
* There are no extra references to clean up.
*/
- goto out_put;
+ goto out_subsys_put;
}
/*
goto out_unlink;
}
- owner = type->ct_owner;
- if (!try_module_get(owner)) {
+ new_item_owner = type->ct_owner;
+ if (!try_module_get(new_item_owner)) {
ret = -EINVAL;
goto out_unlink;
}
spin_lock(&configfs_dirent_lock);
sd->s_type &= ~CONFIGFS_USET_IN_MKDIR;
+ if (!ret)
+ configfs_dir_set_ready(dentry->d_fsdata);
spin_unlock(&configfs_dirent_lock);
out_unlink:
mutex_unlock(&subsys->su_mutex);
if (module_got)
- module_put(owner);
+ module_put(new_item_owner);
}
+out_subsys_put:
+ if (ret)
+ module_put(subsys_owner);
+
out_put:
/*
* link_obj()/link_group() took a reference from child->parent,
struct config_item *item;
struct configfs_subsystem *subsys;
struct configfs_dirent *sd;
- struct module *owner = NULL;
+ struct module *subsys_owner = NULL, *dead_item_owner = NULL;
int ret;
if (dentry->d_parent == configfs_sb->s_root)
return -EINVAL;
}
+ /* configfs_mkdir() shouldn't have allowed this */
+ BUG_ON(!subsys->su_group.cg_item.ci_type);
+ subsys_owner = subsys->su_group.cg_item.ci_type->ct_owner;
+
+ /*
+ * Ensure that no racing symlink() will make detach_prep() fail while
+ * the new link is temporarily attached
+ */
+ mutex_lock(&configfs_symlink_mutex);
spin_lock(&configfs_dirent_lock);
do {
struct mutex *wait_mutex;
if (ret) {
configfs_detach_rollback(dentry);
spin_unlock(&configfs_dirent_lock);
+ mutex_unlock(&configfs_symlink_mutex);
if (ret != -EAGAIN) {
config_item_put(parent_item);
return ret;
mutex_lock(wait_mutex);
mutex_unlock(wait_mutex);
+ mutex_lock(&configfs_symlink_mutex);
spin_lock(&configfs_dirent_lock);
}
} while (ret == -EAGAIN);
spin_unlock(&configfs_dirent_lock);
+ mutex_unlock(&configfs_symlink_mutex);
/* Get a working ref for the duration of this function */
item = configfs_get_config_item(dentry);
config_item_put(parent_item);
if (item->ci_type)
- owner = item->ci_type->ct_owner;
+ dead_item_owner = item->ci_type->ct_owner;
if (sd->s_type & CONFIGFS_USET_DIR) {
configfs_detach_group(item);
/* Drop our reference from above */
config_item_put(item);
- module_put(owner);
+ module_put(dead_item_owner);
+ module_put(subsys_owner);
return 0;
}
{
struct dentry * dentry = file->f_path.dentry;
struct configfs_dirent * parent_sd = dentry->d_fsdata;
+ int err;
mutex_lock(&dentry->d_inode->i_mutex);
- file->private_data = configfs_new_dirent(parent_sd, NULL);
+ /*
+ * Fake invisibility if dir belongs to a group/default groups hierarchy
+ * being attached
+ */
+ err = -ENOENT;
+ if (configfs_dirent_is_ready(parent_sd)) {
+ file->private_data = configfs_new_dirent(parent_sd, NULL);
+ if (IS_ERR(file->private_data))
+ err = PTR_ERR(file->private_data);
+ else
+ err = 0;
+ }
mutex_unlock(&dentry->d_inode->i_mutex);
- return IS_ERR(file->private_data) ? PTR_ERR(file->private_data) : 0;
-
+ return err;
}
static int configfs_dir_close(struct inode *inode, struct file *file)
if (err) {
d_delete(dentry);
dput(dentry);
+ } else {
+ spin_lock(&configfs_dirent_lock);
+ configfs_dir_set_ready(dentry->d_fsdata);
+ spin_unlock(&configfs_dirent_lock);
}
}
mutex_lock_nested(&configfs_sb->s_root->d_inode->i_mutex,
I_MUTEX_PARENT);
mutex_lock_nested(&dentry->d_inode->i_mutex, I_MUTEX_CHILD);
+ mutex_lock(&configfs_symlink_mutex);
spin_lock(&configfs_dirent_lock);
if (configfs_detach_prep(dentry, NULL)) {
printk(KERN_ERR "configfs: Tried to unregister non-empty subsystem!\n");
}
spin_unlock(&configfs_dirent_lock);
+ mutex_unlock(&configfs_symlink_mutex);
configfs_detach_group(&group->cg_item);
dentry->d_inode->i_flags |= S_DEAD;
mutex_unlock(&dentry->d_inode->i_mutex);
#include <linux/configfs.h>
#include "configfs_internal.h"
+/* Protects attachments of new symlinks */
+DEFINE_MUTEX(configfs_symlink_mutex);
+
static int item_depth(struct config_item * item)
{
struct config_item * p = item;
struct configfs_symlink *sl;
int ret;
+ ret = -ENOENT;
+ if (!configfs_dirent_is_ready(target_sd))
+ goto out;
ret = -ENOMEM;
sl = kmalloc(sizeof(struct configfs_symlink), GFP_KERNEL);
if (sl) {
sl->sl_target = config_item_get(item);
spin_lock(&configfs_dirent_lock);
+ if (target_sd->s_type & CONFIGFS_USET_DROPPING) {
+ spin_unlock(&configfs_dirent_lock);
+ config_item_put(item);
+ kfree(sl);
+ return -ENOENT;
+ }
list_add(&sl->sl_list, &target_sd->s_links);
spin_unlock(&configfs_dirent_lock);
ret = configfs_create_link(sl, parent_item->ci_dentry,
}
}
+out:
return ret;
}
{
int ret;
struct nameidata nd;
+ struct configfs_dirent *sd;
struct config_item *parent_item;
struct config_item *target_item;
struct config_item_type *type;
if (dentry->d_parent == configfs_sb->s_root)
goto out;
+ sd = dentry->d_parent->d_fsdata;
+ /*
+ * Fake invisibility if dir belongs to a group/default groups hierarchy
+ * being attached
+ */
+ ret = -ENOENT;
+ if (!configfs_dirent_is_ready(sd))
+ goto out;
+
parent_item = configfs_get_config_item(dentry->d_parent);
type = parent_item->ci_type;
+ ret = -EPERM;
if (!type || !type->ct_item_ops ||
!type->ct_item_ops->allow_link)
goto out_put;
ret = type->ct_item_ops->allow_link(parent_item, target_item);
if (!ret) {
+ mutex_lock(&configfs_symlink_mutex);
ret = create_link(parent_item, target_item, dentry);
+ mutex_unlock(&configfs_symlink_mutex);
if (ret && type->ct_item_ops->drop_link)
type->ct_item_ops->drop_link(parent_item,
target_item);
return new;
}
+/**
+ * d_add_ci - lookup or allocate new dentry with case-exact name
+ * @inode: the inode case-insensitive lookup has found
+ * @dentry: the negative dentry that was passed to the parent's lookup func
+ * @name: the case-exact name to be associated with the returned dentry
+ *
+ * This is to avoid filling the dcache with case-insensitive names to the
+ * same inode, only the actual correct case is stored in the dcache for
+ * case-insensitive filesystems.
+ *
+ * For a case-insensitive lookup match and if the the case-exact dentry
+ * already exists in in the dcache, use it and return it.
+ *
+ * If no entry exists with the exact case name, allocate new dentry with
+ * the exact case, and return the spliced entry.
+ */
+struct dentry *d_add_ci(struct inode *inode, struct dentry *dentry,
+ struct qstr *name)
+{
+ int error;
+ struct dentry *found;
+ struct dentry *new;
+
+ /* Does a dentry matching the name exist already? */
+ found = d_hash_and_lookup(dentry->d_parent, name);
+ /* If not, create it now and return */
+ if (!found) {
+ new = d_alloc(dentry->d_parent, name);
+ if (!new) {
+ error = -ENOMEM;
+ goto err_out;
+ }
+ found = d_splice_alias(inode, new);
+ if (found) {
+ dput(new);
+ return found;
+ }
+ return new;
+ }
+ /* Matching dentry exists, check if it is negative. */
+ if (found->d_inode) {
+ if (unlikely(found->d_inode != inode)) {
+ /* This can't happen because bad inodes are unhashed. */
+ BUG_ON(!is_bad_inode(inode));
+ BUG_ON(!is_bad_inode(found->d_inode));
+ }
+ /*
+ * Already have the inode and the dentry attached, decrement
+ * the reference count to balance the iget() done
+ * earlier on. We found the dentry using d_lookup() so it
+ * cannot be disconnected and thus we do not need to worry
+ * about any NFS/disconnectedness issues here.
+ */
+ iput(inode);
+ return found;
+ }
+ /*
+ * Negative dentry: instantiate it unless the inode is a directory and
+ * has a 'disconnected' dentry (i.e. IS_ROOT and DCACHE_DISCONNECTED),
+ * in which case d_move() that in place of the found dentry.
+ */
+ if (!S_ISDIR(inode->i_mode)) {
+ /* Not a directory; everything is easy. */
+ d_instantiate(found, inode);
+ return found;
+ }
+ spin_lock(&dcache_lock);
+ if (list_empty(&inode->i_dentry)) {
+ /*
+ * Directory without a 'disconnected' dentry; we need to do
+ * d_instantiate() by hand because it takes dcache_lock which
+ * we already hold.
+ */
+ list_add(&found->d_alias, &inode->i_dentry);
+ found->d_inode = inode;
+ spin_unlock(&dcache_lock);
+ security_d_instantiate(found, inode);
+ return found;
+ }
+ /*
+ * Directory with a 'disconnected' dentry; get a reference to the
+ * 'disconnected' dentry.
+ */
+ new = list_entry(inode->i_dentry.next, struct dentry, d_alias);
+ dget_locked(new);
+ spin_unlock(&dcache_lock);
+ /* Do security vodoo. */
+ security_d_instantiate(found, inode);
+ /* Move new in place of found. */
+ d_move(new, found);
+ /* Balance the iget() we did above. */
+ iput(inode);
+ /* Throw away found. */
+ dput(found);
+ /* Use new as the actual dentry. */
+ return new;
+
+err_out:
+ iput(inode);
+ return ERR_PTR(error);
+}
/**
* d_lookup - search for a dentry
EXPORT_SYMBOL(d_prune_aliases);
EXPORT_SYMBOL(d_rehash);
EXPORT_SYMBOL(d_splice_alias);
+EXPORT_SYMBOL(d_add_ci);
EXPORT_SYMBOL(d_validate);
EXPORT_SYMBOL(dget_locked);
EXPORT_SYMBOL(dput);
#define DEVPTS_DEFAULT_MODE 0600
extern int pty_limit; /* Config limit on Unix98 ptys */
-static DEFINE_IDR(allocated_ptys);
+static DEFINE_IDA(allocated_ptys);
static DEFINE_MUTEX(allocated_ptys_lock);
static struct vfsmount *devpts_mnt;
int devpts_new_index(void)
{
int index;
- int idr_ret;
+ int ida_ret;
retry:
- if (!idr_pre_get(&allocated_ptys, GFP_KERNEL)) {
+ if (!ida_pre_get(&allocated_ptys, GFP_KERNEL)) {
return -ENOMEM;
}
mutex_lock(&allocated_ptys_lock);
- idr_ret = idr_get_new(&allocated_ptys, NULL, &index);
- if (idr_ret < 0) {
+ ida_ret = ida_get_new(&allocated_ptys, &index);
+ if (ida_ret < 0) {
mutex_unlock(&allocated_ptys_lock);
- if (idr_ret == -EAGAIN)
+ if (ida_ret == -EAGAIN)
goto retry;
return -EIO;
}
if (index >= pty_limit) {
- idr_remove(&allocated_ptys, index);
+ ida_remove(&allocated_ptys, index);
mutex_unlock(&allocated_ptys_lock);
return -EIO;
}
void devpts_kill_index(int idx)
{
mutex_lock(&allocated_ptys_lock);
- idr_remove(&allocated_ptys, idx);
+ ida_remove(&allocated_ptys, idx);
mutex_unlock(&allocated_ptys_lock);
}
return ret;
}
+int vfs_quota_on_path(struct super_block *sb, int type, int format_id,
+ struct path *path)
+{
+ int error = security_quota_on(path->dentry);
+ if (error)
+ return error;
+ /* Quota file not on the same filesystem? */
+ if (path->mnt->mnt_sb != sb)
+ error = -EXDEV;
+ else
+ error = vfs_quota_on_inode(path->dentry->d_inode, type,
+ format_id);
+ return error;
+}
+
/* Actual function called from quotactl() */
int vfs_quota_on(struct super_block *sb, int type, int format_id, char *path,
int remount)
return vfs_quota_on_remount(sb, type);
error = path_lookup(path, LOOKUP_FOLLOW, &nd);
- if (error < 0)
- return error;
- error = security_quota_on(nd.path.dentry);
- if (error)
- goto out_path;
- /* Quota file not on the same filesystem? */
- if (nd.path.mnt->mnt_sb != sb)
- error = -EXDEV;
- else
- error = vfs_quota_on_inode(nd.path.dentry->d_inode, type,
- format_id);
-out_path:
- path_put(&nd.path);
+ if (!error) {
+ error = vfs_quota_on_path(sb, type, format_id, &nd.path);
+ path_put(&nd.path);
+ }
return error;
}
EXPORT_SYMBOL(dqstats);
EXPORT_SYMBOL(dq_data_lock);
EXPORT_SYMBOL(vfs_quota_on);
+EXPORT_SYMBOL(vfs_quota_on_path);
EXPORT_SYMBOL(vfs_quota_on_mount);
EXPORT_SYMBOL(vfs_quota_off);
EXPORT_SYMBOL(vfs_quota_sync);
journal_unlock_updates(EXT3_SB(sb)->s_journal);
}
+ err = vfs_quota_on_path(sb, type, format_id, &nd.path);
path_put(&nd.path);
- return vfs_quota_on(sb, type, format_id, path, remount);
+ return err;
}
/* Read data from quotafile - avoid pagecache and such because we cannot afford
acl = posix_acl_alloc(count, GFP_NOFS);
if (!acl)
return ERR_PTR(-ENOMEM);
- for (n=0; n < count; n++) {
+ for (n = 0; n < count; n++) {
ext4_acl_entry *entry =
(ext4_acl_entry *)value;
if ((char *)value + sizeof(ext4_acl_entry_short) > end)
goto fail;
acl->a_entries[n].e_tag = le16_to_cpu(entry->e_tag);
acl->a_entries[n].e_perm = le16_to_cpu(entry->e_perm);
- switch(acl->a_entries[n].e_tag) {
- case ACL_USER_OBJ:
- case ACL_GROUP_OBJ:
- case ACL_MASK:
- case ACL_OTHER:
- value = (char *)value +
- sizeof(ext4_acl_entry_short);
- acl->a_entries[n].e_id = ACL_UNDEFINED_ID;
- break;
-
- case ACL_USER:
- case ACL_GROUP:
- value = (char *)value + sizeof(ext4_acl_entry);
- if ((char *)value > end)
- goto fail;
- acl->a_entries[n].e_id =
- le32_to_cpu(entry->e_id);
- break;
-
- default:
+
+ switch (acl->a_entries[n].e_tag) {
+ case ACL_USER_OBJ:
+ case ACL_GROUP_OBJ:
+ case ACL_MASK:
+ case ACL_OTHER:
+ value = (char *)value +
+ sizeof(ext4_acl_entry_short);
+ acl->a_entries[n].e_id = ACL_UNDEFINED_ID;
+ break;
+
+ case ACL_USER:
+ case ACL_GROUP:
+ value = (char *)value + sizeof(ext4_acl_entry);
+ if ((char *)value > end)
goto fail;
+ acl->a_entries[n].e_id =
+ le32_to_cpu(entry->e_id);
+ break;
+
+ default:
+ goto fail;
}
}
if (value != end)
return ERR_PTR(-ENOMEM);
ext_acl->a_version = cpu_to_le32(EXT4_ACL_VERSION);
e = (char *)ext_acl + sizeof(ext4_acl_header);
- for (n=0; n < acl->a_count; n++) {
+ for (n = 0; n < acl->a_count; n++) {
ext4_acl_entry *entry = (ext4_acl_entry *)e;
entry->e_tag = cpu_to_le16(acl->a_entries[n].e_tag);
entry->e_perm = cpu_to_le16(acl->a_entries[n].e_perm);
- switch(acl->a_entries[n].e_tag) {
- case ACL_USER:
- case ACL_GROUP:
- entry->e_id =
- cpu_to_le32(acl->a_entries[n].e_id);
- e += sizeof(ext4_acl_entry);
- break;
-
- case ACL_USER_OBJ:
- case ACL_GROUP_OBJ:
- case ACL_MASK:
- case ACL_OTHER:
- e += sizeof(ext4_acl_entry_short);
- break;
-
- default:
- goto fail;
+ switch (acl->a_entries[n].e_tag) {
+ case ACL_USER:
+ case ACL_GROUP:
+ entry->e_id = cpu_to_le32(acl->a_entries[n].e_id);
+ e += sizeof(ext4_acl_entry);
+ break;
+
+ case ACL_USER_OBJ:
+ case ACL_GROUP_OBJ:
+ case ACL_MASK:
+ case ACL_OTHER:
+ e += sizeof(ext4_acl_entry_short);
+ break;
+
+ default:
+ goto fail;
}
}
return (char *)ext_acl;
if (!test_opt(inode->i_sb, POSIX_ACL))
return NULL;
- switch(type) {
- case ACL_TYPE_ACCESS:
- acl = ext4_iget_acl(inode, &ei->i_acl);
- if (acl != EXT4_ACL_NOT_CACHED)
- return acl;
- name_index = EXT4_XATTR_INDEX_POSIX_ACL_ACCESS;
- break;
-
- case ACL_TYPE_DEFAULT:
- acl = ext4_iget_acl(inode, &ei->i_default_acl);
- if (acl != EXT4_ACL_NOT_CACHED)
- return acl;
- name_index = EXT4_XATTR_INDEX_POSIX_ACL_DEFAULT;
- break;
-
- default:
- return ERR_PTR(-EINVAL);
+ switch (type) {
+ case ACL_TYPE_ACCESS:
+ acl = ext4_iget_acl(inode, &ei->i_acl);
+ if (acl != EXT4_ACL_NOT_CACHED)
+ return acl;
+ name_index = EXT4_XATTR_INDEX_POSIX_ACL_ACCESS;
+ break;
+
+ case ACL_TYPE_DEFAULT:
+ acl = ext4_iget_acl(inode, &ei->i_default_acl);
+ if (acl != EXT4_ACL_NOT_CACHED)
+ return acl;
+ name_index = EXT4_XATTR_INDEX_POSIX_ACL_DEFAULT;
+ break;
+
+ default:
+ return ERR_PTR(-EINVAL);
}
retval = ext4_xattr_get(inode, name_index, "", NULL, 0);
if (retval > 0) {
kfree(value);
if (!IS_ERR(acl)) {
- switch(type) {
- case ACL_TYPE_ACCESS:
- ext4_iset_acl(inode, &ei->i_acl, acl);
- break;
-
- case ACL_TYPE_DEFAULT:
- ext4_iset_acl(inode, &ei->i_default_acl, acl);
- break;
+ switch (type) {
+ case ACL_TYPE_ACCESS:
+ ext4_iset_acl(inode, &ei->i_acl, acl);
+ break;
+
+ case ACL_TYPE_DEFAULT:
+ ext4_iset_acl(inode, &ei->i_default_acl, acl);
+ break;
}
}
return acl;
if (S_ISLNK(inode->i_mode))
return -EOPNOTSUPP;
- switch(type) {
- case ACL_TYPE_ACCESS:
- name_index = EXT4_XATTR_INDEX_POSIX_ACL_ACCESS;
- if (acl) {
- mode_t mode = inode->i_mode;
- error = posix_acl_equiv_mode(acl, &mode);
- if (error < 0)
- return error;
- else {
- inode->i_mode = mode;
- ext4_mark_inode_dirty(handle, inode);
- if (error == 0)
- acl = NULL;
- }
+ switch (type) {
+ case ACL_TYPE_ACCESS:
+ name_index = EXT4_XATTR_INDEX_POSIX_ACL_ACCESS;
+ if (acl) {
+ mode_t mode = inode->i_mode;
+ error = posix_acl_equiv_mode(acl, &mode);
+ if (error < 0)
+ return error;
+ else {
+ inode->i_mode = mode;
+ ext4_mark_inode_dirty(handle, inode);
+ if (error == 0)
+ acl = NULL;
}
- break;
+ }
+ break;
- case ACL_TYPE_DEFAULT:
- name_index = EXT4_XATTR_INDEX_POSIX_ACL_DEFAULT;
- if (!S_ISDIR(inode->i_mode))
- return acl ? -EACCES : 0;
- break;
+ case ACL_TYPE_DEFAULT:
+ name_index = EXT4_XATTR_INDEX_POSIX_ACL_DEFAULT;
+ if (!S_ISDIR(inode->i_mode))
+ return acl ? -EACCES : 0;
+ break;
- default:
- return -EINVAL;
+ default:
+ return -EINVAL;
}
if (acl) {
value = ext4_acl_to_disk(acl, &size);
kfree(value);
if (!error) {
- switch(type) {
- case ACL_TYPE_ACCESS:
- ext4_iset_acl(inode, &ei->i_acl, acl);
- break;
-
- case ACL_TYPE_DEFAULT:
- ext4_iset_acl(inode, &ei->i_default_acl, acl);
- break;
+ switch (type) {
+ case ACL_TYPE_ACCESS:
+ ext4_iset_acl(inode, &ei->i_acl, acl);
+ break;
+
+ case ACL_TYPE_DEFAULT:
+ ext4_iset_acl(inode, &ei->i_default_acl, acl);
+ break;
}
}
return error;
if (unlikely(!bh)) {
ext4_error(sb, __func__,
"Cannot read block bitmap - "
- "block_group = %d, block_bitmap = %llu",
- (int)block_group, (unsigned long long)bitmap_blk);
+ "block_group = %lu, block_bitmap = %llu",
+ block_group, bitmap_blk);
return NULL;
}
if (bh_uptodate_or_lock(bh))
return bh;
+ spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_BLOCK_UNINIT)) {
ext4_init_block_bitmap(sb, bh, block_group, desc);
set_buffer_uptodate(bh);
unlock_buffer(bh);
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), block_group));
return bh;
}
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), block_group));
if (bh_submit_read(bh) < 0) {
put_bh(bh);
ext4_error(sb, __func__,
"Cannot read block bitmap - "
- "block_group = %d, block_bitmap = %llu",
- (int)block_group, (unsigned long long)bitmap_blk);
+ "block_group = %lu, block_bitmap = %llu",
+ block_group, bitmap_blk);
return NULL;
}
ext4_valid_block_bitmap(sb, desc, block_group, bh);
/* inode.c */
-void ext4_da_release_space(struct inode *inode, int used, int to_free);
int ext4_forget(handle_t *handle, int is_metadata, struct inode *inode,
struct buffer_head *bh, ext4_fsblk_t blocknr);
struct buffer_head *ext4_getblk(handle_t *, struct inode *,
if (handle->h_buffer_credits > needed)
return 0;
err = ext4_journal_extend(handle, needed);
- if (err)
+ if (err <= 0)
return err;
return ext4_journal_restart(handle, needed);
}
/*
* get the next allocated block if the extent in the path
- * is before the requested block(s)
+ * is before the requested block(s)
*/
if (b2 < b1) {
b2 = ext4_ext_next_allocated_block(path);
BUG_ON(b != ex_ee_block + ex_ee_len - 1);
}
- /* at present, extent can't cross block group: */
- /* leaf + bitmap + group desc + sb + inode */
- credits = 5;
+ /*
+ * 3 for leaf, sb, and inode plus 2 (bmap and group
+ * descriptor) for each block group; assume two block
+ * groups plus ex_ee_len/blocks_per_block_group for
+ * the worst case
+ */
+ credits = 7 + 2*(ex_ee_len/EXT4_BLOCKS_PER_GROUP(inode->i_sb));
if (ex == EXT_FIRST_EXTENT(eh)) {
correct_index = 1;
credits += (ext_depth(inode)) + 1;
unsigned int newdepth;
/* If extent has less than EXT4_EXT_ZERO_LEN zerout directly */
if (allocated <= EXT4_EXT_ZERO_LEN) {
- /* Mark first half uninitialized.
+ /*
+ * iblock == ee_block is handled by the zerouout
+ * at the beginning.
+ * Mark first half uninitialized.
* Mark second half initialized and zero out the
* initialized extent
*/
ex->ee_len = orig_ex.ee_len;
ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
ext4_ext_dirty(handle, inode, path + depth);
- /* zeroed the full extent */
+ /* blocks available from iblock */
return allocated;
} else if (err)
err = PTR_ERR(path);
return err;
}
+ /* get the second half extent details */
ex = path[depth].p_ext;
err = ext4_ext_get_access(handle, inode,
path + depth);
ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
ext4_ext_dirty(handle, inode, path + depth);
/* zeroed the full extent */
+ /* blocks available from iblock */
return allocated;
} else if (err)
*/
orig_ex.ee_len = cpu_to_le16(ee_len -
ext4_ext_get_actual_len(ex3));
- if (newdepth != depth) {
- depth = newdepth;
- ext4_ext_drop_refs(path);
- path = ext4_ext_find_extent(inode, iblock, path);
- if (IS_ERR(path)) {
- err = PTR_ERR(path);
- goto out;
- }
- eh = path[depth].p_hdr;
- ex = path[depth].p_ext;
- if (ex2 != &newex)
- ex2 = ex;
-
- err = ext4_ext_get_access(handle, inode, path + depth);
- if (err)
- goto out;
+ depth = newdepth;
+ ext4_ext_drop_refs(path);
+ path = ext4_ext_find_extent(inode, iblock, path);
+ if (IS_ERR(path)) {
+ err = PTR_ERR(path);
+ goto out;
}
+ eh = path[depth].p_hdr;
+ ex = path[depth].p_ext;
+ if (ex2 != &newex)
+ ex2 = ex;
+
+ err = ext4_ext_get_access(handle, inode, path + depth);
+ if (err)
+ goto out;
+
allocated = max_blocks;
/* If extent has less than EXT4_EXT_ZERO_LEN and we are trying
ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
ext4_ext_dirty(handle, inode, path + depth);
/* zero out the first half */
+ /* blocks available from iblock */
return allocated;
}
}
* Return buffer_head of bitmap on success or NULL.
*/
static struct buffer_head *
-read_inode_bitmap(struct super_block *sb, ext4_group_t block_group)
+ext4_read_inode_bitmap(struct super_block *sb, ext4_group_t block_group)
{
struct ext4_group_desc *desc;
struct buffer_head *bh = NULL;
+ ext4_fsblk_t bitmap_blk;
desc = ext4_get_group_desc(sb, block_group, NULL);
if (!desc)
- goto error_out;
- if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
- bh = sb_getblk(sb, ext4_inode_bitmap(sb, desc));
- if (!buffer_uptodate(bh)) {
- lock_buffer(bh);
- if (!buffer_uptodate(bh)) {
- ext4_init_inode_bitmap(sb, bh, block_group,
- desc);
- set_buffer_uptodate(bh);
- }
- unlock_buffer(bh);
- }
- } else {
- bh = sb_bread(sb, ext4_inode_bitmap(sb, desc));
+ return NULL;
+ bitmap_blk = ext4_inode_bitmap(sb, desc);
+ bh = sb_getblk(sb, bitmap_blk);
+ if (unlikely(!bh)) {
+ ext4_error(sb, __func__,
+ "Cannot read inode bitmap - "
+ "block_group = %lu, inode_bitmap = %llu",
+ block_group, bitmap_blk);
+ return NULL;
}
- if (!bh)
- ext4_error(sb, "read_inode_bitmap",
+ if (bh_uptodate_or_lock(bh))
+ return bh;
+
+ spin_lock(sb_bgl_lock(EXT4_SB(sb), block_group));
+ if (desc->bg_flags & cpu_to_le16(EXT4_BG_INODE_UNINIT)) {
+ ext4_init_inode_bitmap(sb, bh, block_group, desc);
+ set_buffer_uptodate(bh);
+ unlock_buffer(bh);
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), block_group));
+ return bh;
+ }
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), block_group));
+ if (bh_submit_read(bh) < 0) {
+ put_bh(bh);
+ ext4_error(sb, __func__,
"Cannot read inode bitmap - "
"block_group = %lu, inode_bitmap = %llu",
- block_group, ext4_inode_bitmap(sb, desc));
-error_out:
+ block_group, bitmap_blk);
+ return NULL;
+ }
return bh;
}
}
block_group = (ino - 1) / EXT4_INODES_PER_GROUP(sb);
bit = (ino - 1) % EXT4_INODES_PER_GROUP(sb);
- bitmap_bh = read_inode_bitmap(sb, block_group);
+ bitmap_bh = ext4_read_inode_bitmap(sb, block_group);
if (!bitmap_bh)
goto error_return;
goto fail;
brelse(bitmap_bh);
- bitmap_bh = read_inode_bitmap(sb, group);
+ bitmap_bh = ext4_read_inode_bitmap(sb, group);
if (!bitmap_bh)
goto fail;
/* When marking the block group with
* ~EXT4_BG_INODE_UNINIT we don't want to depend
- * on the value of bg_itable_unsed even though
+ * on the value of bg_itable_unused even though
* mke2fs could have initialized the same for us.
* Instead we calculated the value below
*/
block_group = (ino - 1) / EXT4_INODES_PER_GROUP(sb);
bit = (ino - 1) % EXT4_INODES_PER_GROUP(sb);
- bitmap_bh = read_inode_bitmap(sb, block_group);
+ bitmap_bh = ext4_read_inode_bitmap(sb, block_group);
if (!bitmap_bh) {
ext4_warning(sb, __func__,
"inode bitmap error for orphan %lu", ino);
continue;
desc_count += le16_to_cpu(gdp->bg_free_inodes_count);
brelse(bitmap_bh);
- bitmap_bh = read_inode_bitmap(sb, i);
+ bitmap_bh = ext4_read_inode_bitmap(sb, i);
if (!bitmap_bh)
continue;
void ext4_delete_inode (struct inode * inode)
{
handle_t *handle;
+ int err;
if (ext4_should_order_data(inode))
ext4_begin_ordered_truncate(inode, 0);
if (is_bad_inode(inode))
goto no_delete;
- handle = start_transaction(inode);
+ handle = ext4_journal_start(inode, blocks_for_truncate(inode)+3);
if (IS_ERR(handle)) {
+ ext4_std_error(inode->i_sb, PTR_ERR(handle));
/*
* If we're going to skip the normal cleanup, we still need to
* make sure that the in-core orphan linked list is properly
if (IS_SYNC(inode))
handle->h_sync = 1;
inode->i_size = 0;
+ err = ext4_mark_inode_dirty(handle, inode);
+ if (err) {
+ ext4_warning(inode->i_sb, __func__,
+ "couldn't mark inode dirty (err %d)", err);
+ goto stop_handle;
+ }
if (inode->i_blocks)
ext4_truncate(inode);
+
+ /*
+ * ext4_ext_truncate() doesn't reserve any slop when it
+ * restarts journal transactions; therefore there may not be
+ * enough credits left in the handle to remove the inode from
+ * the orphan list and set the dtime field.
+ */
+ if (handle->h_buffer_credits < 3) {
+ err = ext4_journal_extend(handle, 3);
+ if (err > 0)
+ err = ext4_journal_restart(handle, 3);
+ if (err != 0) {
+ ext4_warning(inode->i_sb, __func__,
+ "couldn't extend journal (err %d)", err);
+ stop_handle:
+ ext4_journal_stop(handle);
+ goto no_delete;
+ }
+ }
+
/*
* Kill off the orphan record which ext4_truncate created.
* AKPM: I think this can be inside the above `if'.
return err;
}
+/*
+ * Calculate the number of metadata blocks need to reserve
+ * to allocate @blocks for non extent file based file
+ */
+static int ext4_indirect_calc_metadata_amount(struct inode *inode, int blocks)
+{
+ int icap = EXT4_ADDR_PER_BLOCK(inode->i_sb);
+ int ind_blks, dind_blks, tind_blks;
+
+ /* number of new indirect blocks needed */
+ ind_blks = (blocks + icap - 1) / icap;
+
+ dind_blks = (ind_blks + icap - 1) / icap;
+
+ tind_blks = 1;
+
+ return ind_blks + dind_blks + tind_blks;
+}
+
+/*
+ * Calculate the number of metadata blocks need to reserve
+ * to allocate given number of blocks
+ */
+static int ext4_calc_metadata_amount(struct inode *inode, int blocks)
+{
+ if (EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL)
+ return ext4_ext_calc_metadata_amount(inode, blocks);
+
+ return ext4_indirect_calc_metadata_amount(inode, blocks);
+}
+
+static void ext4_da_update_reserve_space(struct inode *inode, int used)
+{
+ struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
+ int total, mdb, mdb_free;
+
+ spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
+ /* recalculate the number of metablocks still need to be reserved */
+ total = EXT4_I(inode)->i_reserved_data_blocks - used;
+ mdb = ext4_calc_metadata_amount(inode, total);
+
+ /* figure out how many metablocks to release */
+ BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
+ mdb_free = EXT4_I(inode)->i_reserved_meta_blocks - mdb;
+
+ /* Account for allocated meta_blocks */
+ mdb_free -= EXT4_I(inode)->i_allocated_meta_blocks;
+
+ /* update fs free blocks counter for truncate case */
+ percpu_counter_add(&sbi->s_freeblocks_counter, mdb_free);
+
+ /* update per-inode reservations */
+ BUG_ON(used > EXT4_I(inode)->i_reserved_data_blocks);
+ EXT4_I(inode)->i_reserved_data_blocks -= used;
+
+ BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
+ EXT4_I(inode)->i_reserved_meta_blocks = mdb;
+ EXT4_I(inode)->i_allocated_meta_blocks = 0;
+ spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
+}
+
/* Maximum number of blocks we map for direct IO at once. */
#define DIO_MAX_BLOCKS 4096
/*
/*
+ * The ext4_get_blocks_wrap() function try to look up the requested blocks,
+ * and returns if the blocks are already mapped.
*
- *
- * ext4_ext4 get_block() wrapper function
- * It will do a look up first, and returns if the blocks already mapped.
* Otherwise it takes the write lock of the i_data_sem and allocate blocks
* and store the allocated blocks in the result buffer head and mark it
* mapped.
* which were deferred till now
*/
if ((retval > 0) && buffer_delay(bh))
- ext4_da_release_space(inode, retval, 0);
+ ext4_da_update_reserve_space(inode, retval);
}
up_write((&EXT4_I(inode)->i_data_sem));
{
handle_t *handle = ext4_journal_current_handle();
struct inode *inode = mapping->host;
- unsigned from, to;
int ret = 0, ret2;
- from = pos & (PAGE_CACHE_SIZE - 1);
- to = from + len;
-
ret = ext4_jbd2_file_inode(handle, inode);
if (ret == 0) {
return ret ? ret : copied;
}
-/*
- * Calculate the number of metadata blocks need to reserve
- * to allocate @blocks for non extent file based file
- */
-static int ext4_indirect_calc_metadata_amount(struct inode *inode, int blocks)
-{
- int icap = EXT4_ADDR_PER_BLOCK(inode->i_sb);
- int ind_blks, dind_blks, tind_blks;
-
- /* number of new indirect blocks needed */
- ind_blks = (blocks + icap - 1) / icap;
-
- dind_blks = (ind_blks + icap - 1) / icap;
-
- tind_blks = 1;
-
- return ind_blks + dind_blks + tind_blks;
-}
-
-/*
- * Calculate the number of metadata blocks need to reserve
- * to allocate given number of blocks
- */
-static int ext4_calc_metadata_amount(struct inode *inode, int blocks)
-{
- if (EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL)
- return ext4_ext_calc_metadata_amount(inode, blocks);
-
- return ext4_indirect_calc_metadata_amount(inode, blocks);
-}
static int ext4_da_reserve_space(struct inode *inode, int nrblocks)
{
spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
return -ENOSPC;
}
-
/* reduce fs free blocks counter */
percpu_counter_sub(&sbi->s_freeblocks_counter, total);
return 0; /* success */
}
-void ext4_da_release_space(struct inode *inode, int used, int to_free)
+static void ext4_da_release_space(struct inode *inode, int to_free)
{
struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
int total, mdb, mdb_free, release;
spin_lock(&EXT4_I(inode)->i_block_reservation_lock);
/* recalculate the number of metablocks still need to be reserved */
- total = EXT4_I(inode)->i_reserved_data_blocks - used - to_free;
+ total = EXT4_I(inode)->i_reserved_data_blocks - to_free;
mdb = ext4_calc_metadata_amount(inode, total);
/* figure out how many metablocks to release */
BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
mdb_free = EXT4_I(inode)->i_reserved_meta_blocks - mdb;
- /* Account for allocated meta_blocks */
- mdb_free -= EXT4_I(inode)->i_allocated_meta_blocks;
-
release = to_free + mdb_free;
/* update fs free blocks counter for truncate case */
percpu_counter_add(&sbi->s_freeblocks_counter, release);
/* update per-inode reservations */
- BUG_ON(used + to_free > EXT4_I(inode)->i_reserved_data_blocks);
- EXT4_I(inode)->i_reserved_data_blocks -= (used + to_free);
+ BUG_ON(to_free > EXT4_I(inode)->i_reserved_data_blocks);
+ EXT4_I(inode)->i_reserved_data_blocks -= to_free;
BUG_ON(mdb > EXT4_I(inode)->i_reserved_meta_blocks);
EXT4_I(inode)->i_reserved_meta_blocks = mdb;
- EXT4_I(inode)->i_allocated_meta_blocks = 0;
spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
}
}
curr_off = next_off;
} while ((bh = bh->b_this_page) != head);
- ext4_da_release_space(page->mapping->host, 0, to_release);
+ ext4_da_release_space(page->mapping->host, to_release);
}
/*
}
page = __grab_cache_page(mapping, index);
- if (!page)
- return -ENOMEM;
+ if (!page) {
+ ext4_journal_stop(handle);
+ ret = -ENOMEM;
+ goto out;
+ }
*pagep = page;
ret = block_write_begin(file, mapping, pos, len, flags, pagep, fsdata,
}
if (!buffer_uptodate(bh)) {
lock_buffer(bh);
+
+ /*
+ * If the buffer has the write error flag, we have failed
+ * to write out another inode in the same block. In this
+ * case, we don't have to read the block because we may
+ * read the old inode data successfully.
+ */
+ if (buffer_write_io_error(bh) && !buffer_uptodate(bh))
+ set_buffer_uptodate(bh);
+
if (buffer_uptodate(bh)) {
/* someone brought it uptodate while we waited */
unlock_buffer(bh);
if (bh_uptodate_or_lock(bh[i]))
continue;
+ spin_lock(sb_bgl_lock(EXT4_SB(sb), first_group + i));
if (desc->bg_flags & cpu_to_le16(EXT4_BG_BLOCK_UNINIT)) {
ext4_init_block_bitmap(sb, bh[i],
first_group + i, desc);
set_buffer_uptodate(bh[i]);
unlock_buffer(bh[i]);
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), first_group + i));
continue;
}
+ spin_unlock(sb_bgl_lock(EXT4_SB(sb), first_group + i));
get_bh(bh[i]);
bh[i]->b_end_io = end_buffer_read_sync;
submit_bh(READ, bh[i]);
int ext4_mb_init(struct super_block *sb, int needs_recovery)
{
struct ext4_sb_info *sbi = EXT4_SB(sb);
- unsigned i;
+ unsigned i, j;
unsigned offset;
unsigned max;
int ret;
sbi->s_mb_history_filter = EXT4_MB_HISTORY_DEFAULT;
sbi->s_mb_group_prealloc = MB_DEFAULT_GROUP_PREALLOC;
- i = sizeof(struct ext4_locality_group) * NR_CPUS;
+ i = sizeof(struct ext4_locality_group) * nr_cpu_ids;
sbi->s_locality_groups = kmalloc(i, GFP_KERNEL);
if (sbi->s_locality_groups == NULL) {
clear_opt(sbi->s_mount_opt, MBALLOC);
kfree(sbi->s_mb_maxs);
return -ENOMEM;
}
- for (i = 0; i < NR_CPUS; i++) {
+ for (i = 0; i < nr_cpu_ids; i++) {
struct ext4_locality_group *lg;
lg = &sbi->s_locality_groups[i];
mutex_init(&lg->lg_mutex);
- INIT_LIST_HEAD(&lg->lg_prealloc_list);
+ for (j = 0; j < PREALLOC_TB_SIZE; j++)
+ INIT_LIST_HEAD(&lg->lg_prealloc_list[j]);
spin_lock_init(&lg->lg_prealloc_lock);
}
struct ext4_prealloc_space *pa)
{
unsigned int len = ac->ac_o_ex.fe_len;
+
ext4_get_group_no_and_offset(ac->ac_sb, pa->pa_pstart,
&ac->ac_b_ex.fe_group,
&ac->ac_b_ex.fe_start);
static noinline_for_stack int
ext4_mb_use_preallocated(struct ext4_allocation_context *ac)
{
+ int order, i;
struct ext4_inode_info *ei = EXT4_I(ac->ac_inode);
struct ext4_locality_group *lg;
struct ext4_prealloc_space *pa;
lg = ac->ac_lg;
if (lg == NULL)
return 0;
-
- rcu_read_lock();
- list_for_each_entry_rcu(pa, &lg->lg_prealloc_list, pa_inode_list) {
- spin_lock(&pa->pa_lock);
- if (pa->pa_deleted == 0 && pa->pa_free >= ac->ac_o_ex.fe_len) {
- atomic_inc(&pa->pa_count);
- ext4_mb_use_group_pa(ac, pa);
+ order = fls(ac->ac_o_ex.fe_len) - 1;
+ if (order > PREALLOC_TB_SIZE - 1)
+ /* The max size of hash table is PREALLOC_TB_SIZE */
+ order = PREALLOC_TB_SIZE - 1;
+
+ for (i = order; i < PREALLOC_TB_SIZE; i++) {
+ rcu_read_lock();
+ list_for_each_entry_rcu(pa, &lg->lg_prealloc_list[i],
+ pa_inode_list) {
+ spin_lock(&pa->pa_lock);
+ if (pa->pa_deleted == 0 &&
+ pa->pa_free >= ac->ac_o_ex.fe_len) {
+ atomic_inc(&pa->pa_count);
+ ext4_mb_use_group_pa(ac, pa);
+ spin_unlock(&pa->pa_lock);
+ ac->ac_criteria = 20;
+ rcu_read_unlock();
+ return 1;
+ }
spin_unlock(&pa->pa_lock);
- ac->ac_criteria = 20;
- rcu_read_unlock();
- return 1;
}
- spin_unlock(&pa->pa_lock);
+ rcu_read_unlock();
}
- rcu_read_unlock();
-
return 0;
}
pa->pa_free = pa->pa_len;
atomic_set(&pa->pa_count, 1);
spin_lock_init(&pa->pa_lock);
+ INIT_LIST_HEAD(&pa->pa_inode_list);
pa->pa_deleted = 0;
pa->pa_linear = 1;
list_add(&pa->pa_group_list, &grp->bb_prealloc_list);
ext4_unlock_group(sb, ac->ac_b_ex.fe_group);
- spin_lock(pa->pa_obj_lock);
- list_add_tail_rcu(&pa->pa_inode_list, &lg->lg_prealloc_list);
- spin_unlock(pa->pa_obj_lock);
-
+ /*
+ * We will later add the new pa to the right bucket
+ * after updating the pa_free in ext4_mb_release_context
+ */
return 0;
}
bitmap_bh = ext4_read_block_bitmap(sb, group);
if (bitmap_bh == NULL) {
- /* error handling here */
- ext4_mb_release_desc(&e4b);
- BUG_ON(bitmap_bh == NULL);
+ ext4_error(sb, __func__, "Error in reading block "
+ "bitmap for %lu\n", group);
+ return 0;
}
err = ext4_mb_load_buddy(sb, group, &e4b);
- BUG_ON(err != 0); /* error handling here */
+ if (err) {
+ ext4_error(sb, __func__, "Error in loading buddy "
+ "information for %lu\n", group);
+ put_bh(bitmap_bh);
+ return 0;
+ }
if (needed == 0)
needed = EXT4_BLOCKS_PER_GROUP(sb) + 1;
- grp = ext4_get_group_info(sb, group);
INIT_LIST_HEAD(&list);
-
ac = kmem_cache_alloc(ext4_ac_cachep, GFP_NOFS);
repeat:
ext4_lock_group(sb, group);
ext4_get_group_no_and_offset(sb, pa->pa_pstart, &group, NULL);
err = ext4_mb_load_buddy(sb, group, &e4b);
- BUG_ON(err != 0); /* error handling here */
+ if (err) {
+ ext4_error(sb, __func__, "Error in loading buddy "
+ "information for %lu\n", group);
+ continue;
+ }
bitmap_bh = ext4_read_block_bitmap(sb, group);
if (bitmap_bh == NULL) {
- /* error handling here */
+ ext4_error(sb, __func__, "Error in reading block "
+ "bitmap for %lu\n", group);
ext4_mb_release_desc(&e4b);
- BUG_ON(bitmap_bh == NULL);
+ continue;
}
ext4_lock_group(sb, group);
}
+static noinline_for_stack void
+ext4_mb_discard_lg_preallocations(struct super_block *sb,
+ struct ext4_locality_group *lg,
+ int order, int total_entries)
+{
+ ext4_group_t group = 0;
+ struct ext4_buddy e4b;
+ struct list_head discard_list;
+ struct ext4_prealloc_space *pa, *tmp;
+ struct ext4_allocation_context *ac;
+
+ mb_debug("discard locality group preallocation\n");
+
+ INIT_LIST_HEAD(&discard_list);
+ ac = kmem_cache_alloc(ext4_ac_cachep, GFP_NOFS);
+
+ spin_lock(&lg->lg_prealloc_lock);
+ list_for_each_entry_rcu(pa, &lg->lg_prealloc_list[order],
+ pa_inode_list) {
+ spin_lock(&pa->pa_lock);
+ if (atomic_read(&pa->pa_count)) {
+ /*
+ * This is the pa that we just used
+ * for block allocation. So don't
+ * free that
+ */
+ spin_unlock(&pa->pa_lock);
+ continue;
+ }
+ if (pa->pa_deleted) {
+ spin_unlock(&pa->pa_lock);
+ continue;
+ }
+ /* only lg prealloc space */
+ BUG_ON(!pa->pa_linear);
+
+ /* seems this one can be freed ... */
+ pa->pa_deleted = 1;
+ spin_unlock(&pa->pa_lock);
+
+ list_del_rcu(&pa->pa_inode_list);
+ list_add(&pa->u.pa_tmp_list, &discard_list);
+
+ total_entries--;
+ if (total_entries <= 5) {
+ /*
+ * we want to keep only 5 entries
+ * allowing it to grow to 8. This
+ * mak sure we don't call discard
+ * soon for this list.
+ */
+ break;
+ }
+ }
+ spin_unlock(&lg->lg_prealloc_lock);
+
+ list_for_each_entry_safe(pa, tmp, &discard_list, u.pa_tmp_list) {
+
+ ext4_get_group_no_and_offset(sb, pa->pa_pstart, &group, NULL);
+ if (ext4_mb_load_buddy(sb, group, &e4b)) {
+ ext4_error(sb, __func__, "Error in loading buddy "
+ "information for %lu\n", group);
+ continue;
+ }
+ ext4_lock_group(sb, group);
+ list_del(&pa->pa_group_list);
+ ext4_mb_release_group_pa(&e4b, pa, ac);
+ ext4_unlock_group(sb, group);
+
+ ext4_mb_release_desc(&e4b);
+ list_del(&pa->u.pa_tmp_list);
+ call_rcu(&(pa)->u.pa_rcu, ext4_mb_pa_callback);
+ }
+ if (ac)
+ kmem_cache_free(ext4_ac_cachep, ac);
+}
+
+/*
+ * We have incremented pa_count. So it cannot be freed at this
+ * point. Also we hold lg_mutex. So no parallel allocation is
+ * possible from this lg. That means pa_free cannot be updated.
+ *
+ * A parallel ext4_mb_discard_group_preallocations is possible.
+ * which can cause the lg_prealloc_list to be updated.
+ */
+
+static void ext4_mb_add_n_trim(struct ext4_allocation_context *ac)
+{
+ int order, added = 0, lg_prealloc_count = 1;
+ struct super_block *sb = ac->ac_sb;
+ struct ext4_locality_group *lg = ac->ac_lg;
+ struct ext4_prealloc_space *tmp_pa, *pa = ac->ac_pa;
+
+ order = fls(pa->pa_free) - 1;
+ if (order > PREALLOC_TB_SIZE - 1)
+ /* The max size of hash table is PREALLOC_TB_SIZE */
+ order = PREALLOC_TB_SIZE - 1;
+ /* Add the prealloc space to lg */
+ rcu_read_lock();
+ list_for_each_entry_rcu(tmp_pa, &lg->lg_prealloc_list[order],
+ pa_inode_list) {
+ spin_lock(&tmp_pa->pa_lock);
+ if (tmp_pa->pa_deleted) {
+ spin_unlock(&pa->pa_lock);
+ continue;
+ }
+ if (!added && pa->pa_free < tmp_pa->pa_free) {
+ /* Add to the tail of the previous entry */
+ list_add_tail_rcu(&pa->pa_inode_list,
+ &tmp_pa->pa_inode_list);
+ added = 1;
+ /*
+ * we want to count the total
+ * number of entries in the list
+ */
+ }
+ spin_unlock(&tmp_pa->pa_lock);
+ lg_prealloc_count++;
+ }
+ if (!added)
+ list_add_tail_rcu(&pa->pa_inode_list,
+ &lg->lg_prealloc_list[order]);
+ rcu_read_unlock();
+
+ /* Now trim the list to be not more than 8 elements */
+ if (lg_prealloc_count > 8) {
+ ext4_mb_discard_lg_preallocations(sb, lg,
+ order, lg_prealloc_count);
+ return;
+ }
+ return ;
+}
+
/*
* release all resource we used in allocation
*/
static int ext4_mb_release_context(struct ext4_allocation_context *ac)
{
- if (ac->ac_pa) {
- if (ac->ac_pa->pa_linear) {
+ struct ext4_prealloc_space *pa = ac->ac_pa;
+ if (pa) {
+ if (pa->pa_linear) {
/* see comment in ext4_mb_use_group_pa() */
- spin_lock(&ac->ac_pa->pa_lock);
- ac->ac_pa->pa_pstart += ac->ac_b_ex.fe_len;
- ac->ac_pa->pa_lstart += ac->ac_b_ex.fe_len;
- ac->ac_pa->pa_free -= ac->ac_b_ex.fe_len;
- ac->ac_pa->pa_len -= ac->ac_b_ex.fe_len;
- spin_unlock(&ac->ac_pa->pa_lock);
+ spin_lock(&pa->pa_lock);
+ pa->pa_pstart += ac->ac_b_ex.fe_len;
+ pa->pa_lstart += ac->ac_b_ex.fe_len;
+ pa->pa_free -= ac->ac_b_ex.fe_len;
+ pa->pa_len -= ac->ac_b_ex.fe_len;
+ spin_unlock(&pa->pa_lock);
+ /*
+ * We want to add the pa to the right bucket.
+ * Remove it from the list and while adding
+ * make sure the list to which we are adding
+ * doesn't grow big.
+ */
+ if (likely(pa->pa_free)) {
+ spin_lock(pa->pa_obj_lock);
+ list_del_rcu(&pa->pa_inode_list);
+ spin_unlock(pa->pa_obj_lock);
+ ext4_mb_add_n_trim(ac);
+ }
}
- ext4_mb_put_pa(ac, ac->ac_sb, ac->ac_pa);
+ ext4_mb_put_pa(ac, ac->ac_sb, pa);
}
if (ac->ac_bitmap_page)
page_cache_release(ac->ac_bitmap_page);
count -= overflow;
}
bitmap_bh = ext4_read_block_bitmap(sb, block_group);
- if (!bitmap_bh)
+ if (!bitmap_bh) {
+ err = -EIO;
goto error_return;
+ }
gdp = ext4_get_group_desc(sb, block_group, &gd_bh);
- if (!gdp)
+ if (!gdp) {
+ err = -EIO;
goto error_return;
+ }
if (in_range(ext4_block_bitmap(sb, gdp), block, count) ||
in_range(ext4_inode_bitmap(sb, gdp), block, count) ||
* Locality group:
* we try to group all related changes together
* so that writeback can flush/allocate them together as well
+ * Size of lg_prealloc_list hash is determined by MB_DEFAULT_GROUP_PREALLOC
+ * (512). We store prealloc space into the hash based on the pa_free blocks
+ * order value.ie, fls(pa_free)-1;
*/
+#define PREALLOC_TB_SIZE 10
struct ext4_locality_group {
/* for allocator */
- struct mutex lg_mutex; /* to serialize allocates */
- struct list_head lg_prealloc_list;/* list of preallocations */
+ /* to serialize allocates */
+ struct mutex lg_mutex;
+ /* list of preallocations */
+ struct list_head lg_prealloc_list[PREALLOC_TB_SIZE];
spinlock_t lg_prealloc_lock;
};
"Inode bitmap not in group (block %llu)",
(unsigned long long)input->inode_bitmap);
else if (outside(input->inode_table, start, end) ||
- outside(itend - 1, start, end))
+ outside(itend - 1, start, end))
ext4_warning(sb, __func__,
"Inode table not in group (blocks %llu-%llu)",
(unsigned long long)input->inode_table, itend - 1);
(unsigned long long)input->inode_bitmap,
start, metaend - 1);
else if (inside(input->inode_table, start, metaend) ||
- inside(itend - 1, start, metaend))
+ inside(itend - 1, start, metaend))
ext4_warning(sb, __func__,
"Inode table (%llu-%llu) overlaps"
"GDT table (%llu-%llu)",
if (err) {
if ((err = ext4_journal_restart(handle, EXT4_MAX_TRANS_DATA)))
return err;
- if ((err = ext4_journal_get_write_access(handle, bh)))
+ if ((err = ext4_journal_get_write_access(handle, bh)))
return err;
- }
+ }
return 0;
}
"EXT4-fs: ext4_add_new_gdb: adding group block %lu\n",
gdb_num);
- /*
- * If we are not using the primary superblock/GDT copy don't resize,
- * because the user tools have no way of handling this. Probably a
- * bad time to do it anyways.
- */
+ /*
+ * If we are not using the primary superblock/GDT copy don't resize,
+ * because the user tools have no way of handling this. Probably a
+ * bad time to do it anyways.
+ */
if (EXT4_SB(sb)->s_sbh->b_blocknr !=
le32_to_cpu(EXT4_SB(sb)->s_es->s_first_data_block)) {
ext4_warning(sb, __func__,
return 0;
exit_inode:
- //ext4_journal_release_buffer(handle, iloc.bh);
+ /* ext4_journal_release_buffer(handle, iloc.bh); */
brelse(iloc.bh);
exit_dindj:
- //ext4_journal_release_buffer(handle, dind);
+ /* ext4_journal_release_buffer(handle, dind); */
exit_primary:
- //ext4_journal_release_buffer(handle, *primary);
+ /* ext4_journal_release_buffer(handle, *primary); */
exit_sbh:
- //ext4_journal_release_buffer(handle, *primary);
+ /* ext4_journal_release_buffer(handle, *primary); */
exit_dind:
brelse(dind);
exit_bh:
if ((err = ext4_journal_get_write_access(handle, sbi->s_sbh)))
goto exit_journal;
- /*
- * We will only either add reserved group blocks to a backup group
- * or remove reserved blocks for the first group in a new group block.
- * Doing both would be mean more complex code, and sane people don't
- * use non-sparse filesystems anymore. This is already checked above.
- */
+ /*
+ * We will only either add reserved group blocks to a backup group
+ * or remove reserved blocks for the first group in a new group block.
+ * Doing both would be mean more complex code, and sane people don't
+ * use non-sparse filesystems anymore. This is already checked above.
+ */
if (gdb_off) {
primary = sbi->s_group_desc[gdb_num];
if ((err = ext4_journal_get_write_access(handle, primary)))
} else if ((err = add_new_gdb(handle, inode, input, &primary)))
goto exit_journal;
- /*
- * OK, now we've set up the new group. Time to make it active.
- *
- * Current kernels don't lock all allocations via lock_super(),
- * so we have to be safe wrt. concurrent accesses the group
- * data. So we need to be careful to set all of the relevant
- * group descriptor data etc. *before* we enable the group.
- *
- * The key field here is sbi->s_groups_count: as long as
- * that retains its old value, nobody is going to access the new
- * group.
- *
- * So first we update all the descriptor metadata for the new
- * group; then we update the total disk blocks count; then we
- * update the groups count to enable the group; then finally we
- * update the free space counts so that the system can start
- * using the new disk blocks.
- */
+ /*
+ * OK, now we've set up the new group. Time to make it active.
+ *
+ * Current kernels don't lock all allocations via lock_super(),
+ * so we have to be safe wrt. concurrent accesses the group
+ * data. So we need to be careful to set all of the relevant
+ * group descriptor data etc. *before* we enable the group.
+ *
+ * The key field here is sbi->s_groups_count: as long as
+ * that retains its old value, nobody is going to access the new
+ * group.
+ *
+ * So first we update all the descriptor metadata for the new
+ * group; then we update the total disk blocks count; then we
+ * update the groups count to enable the group; then finally we
+ * update the free space counts so that the system can start
+ * using the new disk blocks.
+ */
/* Update group descriptor block for new group */
gdp = (struct ext4_group_desc *)((char *)primary->b_data +
return err;
} /* ext4_group_add */
-/* Extend the filesystem to the new number of blocks specified. This entry
+/*
+ * Extend the filesystem to the new number of blocks specified. This entry
* point is only used to extend the current filesystem to the end of the last
* existing group. It can be accessed via ioctl, or by "remount,resize=<size>"
* for emergencies (because it has no dependencies on reserved blocks).
o_blocks_count + add, add);
/* See if the device is actually as big as what was requested */
- bh = sb_bread(sb, o_blocks_count + add -1);
+ bh = sb_bread(sb, o_blocks_count + add - 1);
if (!bh) {
ext4_warning(sb, __func__,
"can't read last block, resize aborted");
unsigned long journal_devnum);
static int ext4_create_journal(struct super_block *, struct ext4_super_block *,
unsigned int);
-static void ext4_commit_super (struct super_block * sb,
- struct ext4_super_block * es,
- int sync);
-static void ext4_mark_recovery_complete(struct super_block * sb,
- struct ext4_super_block * es);
-static void ext4_clear_journal_err(struct super_block * sb,
- struct ext4_super_block * es);
+static void ext4_commit_super(struct super_block *sb,
+ struct ext4_super_block *es, int sync);
+static void ext4_mark_recovery_complete(struct super_block *sb,
+ struct ext4_super_block *es);
+static void ext4_clear_journal_err(struct super_block *sb,
+ struct ext4_super_block *es);
static int ext4_sync_fs(struct super_block *sb, int wait);
-static const char *ext4_decode_error(struct super_block * sb, int errno,
+static const char *ext4_decode_error(struct super_block *sb, int errno,
char nbuf[16]);
-static int ext4_remount (struct super_block * sb, int * flags, char * data);
-static int ext4_statfs (struct dentry * dentry, struct kstatfs * buf);
+static int ext4_remount(struct super_block *sb, int *flags, char *data);
+static int ext4_statfs(struct dentry *dentry, struct kstatfs *buf);
static void ext4_unlockfs(struct super_block *sb);
-static void ext4_write_super (struct super_block * sb);
+static void ext4_write_super(struct super_block *sb);
static void ext4_write_super_lockfs(struct super_block *sb);
if (sb->s_flags & MS_RDONLY)
return;
- if (!test_opt (sb, ERRORS_CONT)) {
+ if (!test_opt(sb, ERRORS_CONT)) {
journal_t *journal = EXT4_SB(sb)->s_journal;
EXT4_SB(sb)->s_mount_opt |= EXT4_MOUNT_ABORT;
if (journal)
jbd2_journal_abort(journal, -EIO);
}
- if (test_opt (sb, ERRORS_RO)) {
- printk (KERN_CRIT "Remounting filesystem read-only\n");
+ if (test_opt(sb, ERRORS_RO)) {
+ printk(KERN_CRIT "Remounting filesystem read-only\n");
sb->s_flags |= MS_RDONLY;
}
ext4_commit_super(sb, es, 1);
sb->s_id);
}
-void ext4_error (struct super_block * sb, const char * function,
- const char * fmt, ...)
+void ext4_error(struct super_block *sb, const char *function,
+ const char *fmt, ...)
{
va_list args;
va_start(args, fmt);
- printk(KERN_CRIT "EXT4-fs error (device %s): %s: ",sb->s_id, function);
+ printk(KERN_CRIT "EXT4-fs error (device %s): %s: ", sb->s_id, function);
vprintk(fmt, args);
printk("\n");
va_end(args);
ext4_handle_error(sb);
}
-static const char *ext4_decode_error(struct super_block * sb, int errno,
+static const char *ext4_decode_error(struct super_block *sb, int errno,
char nbuf[16])
{
char *errstr = NULL;
/* __ext4_std_error decodes expected errors from journaling functions
* automatically and invokes the appropriate error response. */
-void __ext4_std_error (struct super_block * sb, const char * function,
- int errno)
+void __ext4_std_error(struct super_block *sb, const char *function, int errno)
{
char nbuf[16];
const char *errstr;
return;
errstr = ext4_decode_error(sb, errno, nbuf);
- printk (KERN_CRIT "EXT4-fs error (device %s) in %s: %s\n",
- sb->s_id, function, errstr);
+ printk(KERN_CRIT "EXT4-fs error (device %s) in %s: %s\n",
+ sb->s_id, function, errstr);
ext4_handle_error(sb);
}
* case we take the easy way out and panic immediately.
*/
-void ext4_abort (struct super_block * sb, const char * function,
- const char * fmt, ...)
+void ext4_abort(struct super_block *sb, const char *function,
+ const char *fmt, ...)
{
va_list args;
- printk (KERN_CRIT "ext4_abort called.\n");
+ printk(KERN_CRIT "ext4_abort called.\n");
va_start(args, fmt);
- printk(KERN_CRIT "EXT4-fs error (device %s): %s: ",sb->s_id, function);
+ printk(KERN_CRIT "EXT4-fs error (device %s): %s: ", sb->s_id, function);
vprintk(fmt, args);
printk("\n");
va_end(args);
jbd2_journal_abort(EXT4_SB(sb)->s_journal, -EIO);
}
-void ext4_warning (struct super_block * sb, const char * function,
- const char * fmt, ...)
+void ext4_warning(struct super_block *sb, const char *function,
+ const char *fmt, ...)
{
va_list args;
}
}
-static void ext4_put_super (struct super_block * sb)
+static void ext4_put_super(struct super_block *sb)
{
struct ext4_sb_info *sbi = EXT4_SB(sb);
struct ext4_super_block *es = sbi->s_es;
&EXT4_I(inode)->jinode);
}
-static inline void ext4_show_quota_options(struct seq_file *seq, struct super_block *sb)
+static inline void ext4_show_quota_options(struct seq_file *seq,
+ struct super_block *sb)
{
#if defined(CONFIG_QUOTA)
struct ext4_sb_info *sbi = EXT4_SB(sb);
}
#ifdef CONFIG_QUOTA
-#define QTYPE2NAME(t) ((t)==USRQUOTA?"user":"group")
-#define QTYPE2MOPT(on, t) ((t)==USRQUOTA?((on)##USRJQUOTA):((on)##GRPJQUOTA))
+#define QTYPE2NAME(t) ((t) == USRQUOTA?"user":"group")
+#define QTYPE2MOPT(on, t) ((t) == USRQUOTA?((on)##USRJQUOTA):((on)##GRPJQUOTA))
static int ext4_dquot_initialize(struct inode *inode, int type);
static int ext4_dquot_drop(struct inode *inode);
return sb_block;
}
-static int parse_options (char *options, struct super_block *sb,
- unsigned int *inum, unsigned long *journal_devnum,
- ext4_fsblk_t *n_blocks_count, int is_remount)
+static int parse_options(char *options, struct super_block *sb,
+ unsigned int *inum, unsigned long *journal_devnum,
+ ext4_fsblk_t *n_blocks_count, int is_remount)
{
struct ext4_sb_info *sbi = EXT4_SB(sb);
- char * p;
+ char *p;
substring_t args[MAX_OPT_ARGS];
int data_opt = 0;
int option;
if (!options)
return 1;
- while ((p = strsep (&options, ",")) != NULL) {
+ while ((p = strsep(&options, ",")) != NULL) {
int token;
if (!*p)
continue;
token = match_token(p, tokens, args);
switch (token) {
case Opt_bsd_df:
- clear_opt (sbi->s_mount_opt, MINIX_DF);
+ clear_opt(sbi->s_mount_opt, MINIX_DF);
break;
case Opt_minix_df:
- set_opt (sbi->s_mount_opt, MINIX_DF);
+ set_opt(sbi->s_mount_opt, MINIX_DF);
break;
case Opt_grpid:
- set_opt (sbi->s_mount_opt, GRPID);
+ set_opt(sbi->s_mount_opt, GRPID);
break;
case Opt_nogrpid:
- clear_opt (sbi->s_mount_opt, GRPID);
+ clear_opt(sbi->s_mount_opt, GRPID);
break;
case Opt_resuid:
if (match_int(&args[0], &option))
/* *sb_block = match_int(&args[0]); */
break;
case Opt_err_panic:
- clear_opt (sbi->s_mount_opt, ERRORS_CONT);
- clear_opt (sbi->s_mount_opt, ERRORS_RO);
- set_opt (sbi->s_mount_opt, ERRORS_PANIC);
+ clear_opt(sbi->s_mount_opt, ERRORS_CONT);
+ clear_opt(sbi->s_mount_opt, ERRORS_RO);
+ set_opt(sbi->s_mount_opt, ERRORS_PANIC);
break;
case Opt_err_ro:
- clear_opt (sbi->s_mount_opt, ERRORS_CONT);
- clear_opt (sbi->s_mount_opt, ERRORS_PANIC);
- set_opt (sbi->s_mount_opt, ERRORS_RO);
+ clear_opt(sbi->s_mount_opt, ERRORS_CONT);
+ clear_opt(sbi->s_mount_opt, ERRORS_PANIC);
+ set_opt(sbi->s_mount_opt, ERRORS_RO);
break;
case Opt_err_cont:
- clear_opt (sbi->s_mount_opt, ERRORS_RO);
- clear_opt (sbi->s_mount_opt, ERRORS_PANIC);
- set_opt (sbi->s_mount_opt, ERRORS_CONT);
+ clear_opt(sbi->s_mount_opt, ERRORS_RO);
+ clear_opt(sbi->s_mount_opt, ERRORS_PANIC);
+ set_opt(sbi->s_mount_opt, ERRORS_CONT);
break;
case Opt_nouid32:
- set_opt (sbi->s_mount_opt, NO_UID32);
+ set_opt(sbi->s_mount_opt, NO_UID32);
break;
case Opt_nocheck:
- clear_opt (sbi->s_mount_opt, CHECK);
+ clear_opt(sbi->s_mount_opt, CHECK);
break;
case Opt_debug:
- set_opt (sbi->s_mount_opt, DEBUG);
+ set_opt(sbi->s_mount_opt, DEBUG);
break;
case Opt_oldalloc:
- set_opt (sbi->s_mount_opt, OLDALLOC);
+ set_opt(sbi->s_mount_opt, OLDALLOC);
break;
case Opt_orlov:
- clear_opt (sbi->s_mount_opt, OLDALLOC);
+ clear_opt(sbi->s_mount_opt, OLDALLOC);
break;
#ifdef CONFIG_EXT4DEV_FS_XATTR
case Opt_user_xattr:
- set_opt (sbi->s_mount_opt, XATTR_USER);
+ set_opt(sbi->s_mount_opt, XATTR_USER);
break;
case Opt_nouser_xattr:
- clear_opt (sbi->s_mount_opt, XATTR_USER);
+ clear_opt(sbi->s_mount_opt, XATTR_USER);
break;
#else
case Opt_user_xattr:
"journal on remount\n");
return 0;
}
- set_opt (sbi->s_mount_opt, UPDATE_JOURNAL);
+ set_opt(sbi->s_mount_opt, UPDATE_JOURNAL);
break;
case Opt_journal_inum:
if (is_remount) {
set_opt(sbi->s_mount_opt, JOURNAL_CHECKSUM);
break;
case Opt_noload:
- set_opt (sbi->s_mount_opt, NOLOAD);
+ set_opt(sbi->s_mount_opt, NOLOAD);
break;
case Opt_commit:
if (match_int(&args[0], &option))
"on this filesystem, use tune2fs\n");
return 0;
}
- set_opt (sbi->s_mount_opt, EXTENTS);
+ set_opt(sbi->s_mount_opt, EXTENTS);
break;
case Opt_noextents:
/*
"-o noextents options\n");
return 0;
}
- clear_opt (sbi->s_mount_opt, EXTENTS);
+ clear_opt(sbi->s_mount_opt, EXTENTS);
break;
case Opt_i_version:
set_opt(sbi->s_mount_opt, I_VERSION);
set_opt(sbi->s_mount_opt, DELALLOC);
break;
default:
- printk (KERN_ERR
- "EXT4-fs: Unrecognized mount option \"%s\" "
- "or missing value\n", p);
+ printk(KERN_ERR
+ "EXT4-fs: Unrecognized mount option \"%s\" "
+ "or missing value\n", p);
return 0;
}
}
int res = 0;
if (le32_to_cpu(es->s_rev_level) > EXT4_MAX_SUPP_REV) {
- printk (KERN_ERR "EXT4-fs warning: revision level too high, "
- "forcing read-only mode\n");
+ printk(KERN_ERR "EXT4-fs warning: revision level too high, "
+ "forcing read-only mode\n");
res = MS_RDONLY;
}
if (read_only)
return res;
if (!(sbi->s_mount_state & EXT4_VALID_FS))
- printk (KERN_WARNING "EXT4-fs warning: mounting unchecked fs, "
- "running e2fsck is recommended\n");
+ printk(KERN_WARNING "EXT4-fs warning: mounting unchecked fs, "
+ "running e2fsck is recommended\n");
else if ((sbi->s_mount_state & EXT4_ERROR_FS))
- printk (KERN_WARNING
- "EXT4-fs warning: mounting fs with errors, "
- "running e2fsck is recommended\n");
+ printk(KERN_WARNING
+ "EXT4-fs warning: mounting fs with errors, "
+ "running e2fsck is recommended\n");
else if ((__s16) le16_to_cpu(es->s_max_mnt_count) >= 0 &&
le16_to_cpu(es->s_mnt_count) >=
(unsigned short) (__s16) le16_to_cpu(es->s_max_mnt_count))
- printk (KERN_WARNING
- "EXT4-fs warning: maximal mount count reached, "
- "running e2fsck is recommended\n");
+ printk(KERN_WARNING
+ "EXT4-fs warning: maximal mount count reached, "
+ "running e2fsck is recommended\n");
else if (le32_to_cpu(es->s_checkinterval) &&
(le32_to_cpu(es->s_lastcheck) +
le32_to_cpu(es->s_checkinterval) <= get_seconds()))
- printk (KERN_WARNING
- "EXT4-fs warning: checktime reached, "
- "running e2fsck is recommended\n");
+ printk(KERN_WARNING
+ "EXT4-fs warning: checktime reached, "
+ "running e2fsck is recommended\n");
#if 0
/* @@@ We _will_ want to clear the valid bit if we find
* inconsistencies, to force a fsck at reboot. But for
flex_group_count = (sbi->s_groups_count + groups_per_flex - 1) /
groups_per_flex;
- sbi->s_flex_groups = kmalloc(flex_group_count *
+ sbi->s_flex_groups = kzalloc(flex_group_count *
sizeof(struct flex_groups), GFP_KERNEL);
if (sbi->s_flex_groups == NULL) {
- printk(KERN_ERR "EXT4-fs: not enough memory\n");
+ printk(KERN_ERR "EXT4-fs: not enough memory for "
+ "%lu flex groups\n", flex_group_count);
goto failed;
}
- memset(sbi->s_flex_groups, 0, flex_group_count *
- sizeof(struct flex_groups));
gdp = ext4_get_group_desc(sb, 1, &bh);
block_bitmap = ext4_block_bitmap(sb, gdp) - 1;
(EXT4_BLOCKS_PER_GROUP(sb) - 1);
block_bitmap = ext4_block_bitmap(sb, gdp);
- if (block_bitmap < first_block || block_bitmap > last_block)
- {
+ if (block_bitmap < first_block || block_bitmap > last_block) {
printk(KERN_ERR "EXT4-fs: ext4_check_descriptors: "
"Block bitmap for group %lu not in group "
"(block %llu)!", i, block_bitmap);
return 0;
}
inode_bitmap = ext4_inode_bitmap(sb, gdp);
- if (inode_bitmap < first_block || inode_bitmap > last_block)
- {
+ if (inode_bitmap < first_block || inode_bitmap > last_block) {
printk(KERN_ERR "EXT4-fs: ext4_check_descriptors: "
"Inode bitmap for group %lu not in group "
"(block %llu)!", i, inode_bitmap);
}
inode_table = ext4_inode_table(sb, gdp);
if (inode_table < first_block ||
- inode_table + sbi->s_itb_per_group - 1 > last_block)
- {
+ inode_table + sbi->s_itb_per_group - 1 > last_block) {
printk(KERN_ERR "EXT4-fs: ext4_check_descriptors: "
"Inode table for group %lu not in group "
"(block %llu)!", i, inode_table);
return 0;
}
+ spin_lock(sb_bgl_lock(sbi, i));
if (!ext4_group_desc_csum_verify(sbi, i, gdp)) {
printk(KERN_ERR "EXT4-fs: ext4_check_descriptors: "
"Checksum for group %lu failed (%u!=%u)\n",
i, le16_to_cpu(ext4_group_desc_csum(sbi, i,
gdp)), le16_to_cpu(gdp->bg_checksum));
- return 0;
+ if (!(sb->s_flags & MS_RDONLY))
+ return 0;
}
+ spin_unlock(sb_bgl_lock(sbi, i));
if (!flexbg_flag)
first_block += EXT4_BLOCKS_PER_GROUP(sb);
}
ext4_free_blocks_count_set(sbi->s_es, ext4_count_free_blocks(sb));
- sbi->s_es->s_free_inodes_count=cpu_to_le32(ext4_count_free_inodes(sb));
+ sbi->s_es->s_free_inodes_count = cpu_to_le32(ext4_count_free_inodes(sb));
return 1;
}
* e2fsck was run on this filesystem, and it must have already done the orphan
* inode cleanup for us, so we can safely abort without any further action.
*/
-static void ext4_orphan_cleanup (struct super_block * sb,
- struct ext4_super_block * es)
+static void ext4_orphan_cleanup(struct super_block *sb,
+ struct ext4_super_block *es)
{
unsigned int s_flags = sb->s_flags;
int nr_orphans = 0, nr_truncates = 0;
iput(inode); /* The delete magic happens here! */
}
-#define PLURAL(x) (x), ((x)==1) ? "" : "s"
+#define PLURAL(x) (x), ((x) == 1) ? "" : "s"
if (nr_orphans)
printk(KERN_INFO "EXT4-fs: %s: %d orphan inode%s deleted\n",
return 0;
}
-static int ext4_fill_super (struct super_block *sb, void *data, int silent)
+static int ext4_fill_super(struct super_block *sb, void *data, int silent)
__releases(kernel_lock)
__acquires(kernel_lock)
{
- struct buffer_head * bh;
+ struct buffer_head *bh;
struct ext4_super_block *es = NULL;
struct ext4_sb_info *sbi;
ext4_fsblk_t block;
}
if (!(bh = sb_bread(sb, logical_sb_block))) {
- printk (KERN_ERR "EXT4-fs: unable to read superblock\n");
+ printk(KERN_ERR "EXT4-fs: unable to read superblock\n");
goto out_fail;
}
/*
set_opt(sbi->s_mount_opt, DELALLOC);
- if (!parse_options ((char *) data, sb, &journal_inum, &journal_devnum,
- NULL, 0))
+ if (!parse_options((char *) data, sb, &journal_inum, &journal_devnum,
+ NULL, 0))
goto failed_mount;
sb->s_flags = (sb->s_flags & ~MS_POSIXACL) |
goto failed_mount;
}
- brelse (bh);
+ brelse(bh);
logical_sb_block = sb_block * EXT4_MIN_BLOCK_SIZE;
offset = do_div(logical_sb_block, blocksize);
bh = sb_bread(sb, logical_sb_block);
es = (struct ext4_super_block *)(((char *)bh->b_data) + offset);
sbi->s_es = es;
if (es->s_magic != cpu_to_le16(EXT4_SUPER_MAGIC)) {
- printk (KERN_ERR
- "EXT4-fs: Magic mismatch, very weird !\n");
+ printk(KERN_ERR
+ "EXT4-fs: Magic mismatch, very weird !\n");
goto failed_mount;
}
}
if ((sbi->s_inode_size < EXT4_GOOD_OLD_INODE_SIZE) ||
(!is_power_of_2(sbi->s_inode_size)) ||
(sbi->s_inode_size > blocksize)) {
- printk (KERN_ERR
- "EXT4-fs: unsupported inode size: %d\n",
- sbi->s_inode_size);
+ printk(KERN_ERR
+ "EXT4-fs: unsupported inode size: %d\n",
+ sbi->s_inode_size);
goto failed_mount;
}
if (sbi->s_inode_size > EXT4_GOOD_OLD_INODE_SIZE)
sbi->s_mount_state = le16_to_cpu(es->s_state);
sbi->s_addr_per_block_bits = ilog2(EXT4_ADDR_PER_BLOCK(sb));
sbi->s_desc_per_block_bits = ilog2(EXT4_DESC_PER_BLOCK(sb));
- for (i=0; i < 4; i++)
+ for (i = 0; i < 4; i++)
sbi->s_hash_seed[i] = le32_to_cpu(es->s_hash_seed[i]);
sbi->s_def_hash_version = es->s_def_hash_version;
if (sbi->s_blocks_per_group > blocksize * 8) {
- printk (KERN_ERR
- "EXT4-fs: #blocks per group too big: %lu\n",
- sbi->s_blocks_per_group);
+ printk(KERN_ERR
+ "EXT4-fs: #blocks per group too big: %lu\n",
+ sbi->s_blocks_per_group);
goto failed_mount;
}
if (sbi->s_inodes_per_group > blocksize * 8) {
- printk (KERN_ERR
- "EXT4-fs: #inodes per group too big: %lu\n",
- sbi->s_inodes_per_group);
+ printk(KERN_ERR
+ "EXT4-fs: #inodes per group too big: %lu\n",
+ sbi->s_inodes_per_group);
goto failed_mount;
}
sbi->s_groups_count = blocks_count;
db_count = (sbi->s_groups_count + EXT4_DESC_PER_BLOCK(sb) - 1) /
EXT4_DESC_PER_BLOCK(sb);
- sbi->s_group_desc = kmalloc(db_count * sizeof (struct buffer_head *),
+ sbi->s_group_desc = kmalloc(db_count * sizeof(struct buffer_head *),
GFP_KERNEL);
if (sbi->s_group_desc == NULL) {
- printk (KERN_ERR "EXT4-fs: not enough memory\n");
+ printk(KERN_ERR "EXT4-fs: not enough memory\n");
goto failed_mount;
}
block = descriptor_loc(sb, logical_sb_block, i);
sbi->s_group_desc[i] = sb_bread(sb, block);
if (!sbi->s_group_desc[i]) {
- printk (KERN_ERR "EXT4-fs: "
- "can't read group descriptor %d\n", i);
+ printk(KERN_ERR "EXT4-fs: "
+ "can't read group descriptor %d\n", i);
db_count = i;
goto failed_mount2;
}
}
- if (!ext4_check_descriptors (sb)) {
+ if (!ext4_check_descriptors(sb)) {
printk(KERN_ERR "EXT4-fs: group descriptors corrupted!\n");
goto failed_mount2;
}
EXT4_SB(sb)->s_journal->j_failed_commit) {
printk(KERN_CRIT "EXT4-fs error (device %s): "
"ext4_fill_super: Journal transaction "
- "%u is corrupt\n", sb->s_id,
+ "%u is corrupt\n", sb->s_id,
EXT4_SB(sb)->s_journal->j_failed_commit);
- if (test_opt (sb, ERRORS_RO)) {
- printk (KERN_CRIT
- "Mounting filesystem read-only\n");
+ if (test_opt(sb, ERRORS_RO)) {
+ printk(KERN_CRIT
+ "Mounting filesystem read-only\n");
sb->s_flags |= MS_RDONLY;
EXT4_SB(sb)->s_mount_state |= EXT4_ERROR_FS;
es->s_state |= cpu_to_le16(EXT4_ERROR_FS);
goto failed_mount3;
} else {
if (!silent)
- printk (KERN_ERR
- "ext4: No journal on filesystem on %s\n",
- sb->s_id);
+ printk(KERN_ERR
+ "ext4: No journal on filesystem on %s\n",
+ sb->s_id);
goto failed_mount3;
}
goto failed_mount4;
}
- ext4_setup_super (sb, es, sb->s_flags & MS_RDONLY);
+ ext4_setup_super(sb, es, sb->s_flags & MS_RDONLY);
/* determine the minimum size of new large inodes, if present */
if (sbi->s_inode_size > EXT4_GOOD_OLD_INODE_SIZE) {
ext4_orphan_cleanup(sb, es);
EXT4_SB(sb)->s_mount_state &= ~EXT4_ORPHAN_FS;
if (needs_recovery)
- printk (KERN_INFO "EXT4-fs: recovery complete.\n");
+ printk(KERN_INFO "EXT4-fs: recovery complete.\n");
ext4_mark_recovery_complete(sb, es);
- printk (KERN_INFO "EXT4-fs: mounted filesystem with %s data mode.\n",
- test_opt(sb,DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA ? "journal":
- test_opt(sb,DATA_FLAGS) == EXT4_MOUNT_ORDERED_DATA ? "ordered":
- "writeback");
+ printk(KERN_INFO "EXT4-fs: mounted filesystem with %s data mode.\n",
+ test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA ? "journal":
+ test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_ORDERED_DATA ? "ordered":
+ "writeback");
if (test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA) {
printk(KERN_WARNING "EXT4-fs: Ignoring delalloc option - "
static journal_t *ext4_get_dev_journal(struct super_block *sb,
dev_t j_dev)
{
- struct buffer_head * bh;
+ struct buffer_head *bh;
journal_t *journal;
ext4_fsblk_t start;
ext4_fsblk_t len;
int hblock, blocksize;
ext4_fsblk_t sb_block;
unsigned long offset;
- struct ext4_super_block * es;
+ struct ext4_super_block *es;
struct block_device *bdev;
bdev = ext4_blkdev_get(j_dev);
"unavailable, cannot proceed.\n");
return -EROFS;
}
- printk (KERN_INFO "EXT4-fs: write access will "
- "be enabled during recovery.\n");
+ printk(KERN_INFO "EXT4-fs: write access will "
+ "be enabled during recovery.\n");
}
}
return 0;
}
-static int ext4_create_journal(struct super_block * sb,
- struct ext4_super_block * es,
+static int ext4_create_journal(struct super_block *sb,
+ struct ext4_super_block *es,
unsigned int journal_inum)
{
journal_t *journal;
return 0;
}
-static void ext4_commit_super (struct super_block * sb,
- struct ext4_super_block * es,
- int sync)
+static void ext4_commit_super(struct super_block *sb,
+ struct ext4_super_block *es, int sync)
{
struct buffer_head *sbh = EXT4_SB(sb)->s_sbh;
* remounting) the filesystem readonly, then we will end up with a
* consistent fs on disk. Record that fact.
*/
-static void ext4_mark_recovery_complete(struct super_block * sb,
- struct ext4_super_block * es)
+static void ext4_mark_recovery_complete(struct super_block *sb,
+ struct ext4_super_block *es)
{
journal_t *journal = EXT4_SB(sb)->s_journal;
* has recorded an error from a previous lifetime, move that error to the
* main filesystem now.
*/
-static void ext4_clear_journal_err(struct super_block * sb,
- struct ext4_super_block * es)
+static void ext4_clear_journal_err(struct super_block *sb,
+ struct ext4_super_block *es)
{
journal_t *journal;
int j_errno;
EXT4_SB(sb)->s_mount_state |= EXT4_ERROR_FS;
es->s_state |= cpu_to_le16(EXT4_ERROR_FS);
- ext4_commit_super (sb, es, 1);
+ ext4_commit_super(sb, es, 1);
jbd2_journal_clear_err(journal);
}
* This implicitly triggers the writebehind on sync().
*/
-static void ext4_write_super (struct super_block * sb)
+static void ext4_write_super(struct super_block *sb)
{
if (mutex_trylock(&sb->s_lock) != 0)
BUG();
}
}
-static int ext4_remount (struct super_block * sb, int * flags, char * data)
+static int ext4_remount(struct super_block *sb, int *flags, char *data)
{
- struct ext4_super_block * es;
+ struct ext4_super_block *es;
struct ext4_sb_info *sbi = EXT4_SB(sb);
ext4_fsblk_t n_blocks_count = 0;
unsigned long old_sb_flags;
struct ext4_mount_options old_opts;
+ ext4_group_t g;
int err;
#ifdef CONFIG_QUOTA
int i;
goto restore_opts;
}
+ /*
+ * Make sure the group descriptor checksums
+ * are sane. If they aren't, refuse to
+ * remount r/w.
+ */
+ for (g = 0; g < sbi->s_groups_count; g++) {
+ struct ext4_group_desc *gdp =
+ ext4_get_group_desc(sb, g, NULL);
+
+ if (!ext4_group_desc_csum_verify(sbi, g, gdp)) {
+ printk(KERN_ERR
+ "EXT4-fs: ext4_remount: "
+ "Checksum for group %lu failed (%u!=%u)\n",
+ g, le16_to_cpu(ext4_group_desc_csum(sbi, g, gdp)),
+ le16_to_cpu(gdp->bg_checksum));
+ err = -EINVAL;
+ goto restore_opts;
+ }
+ }
+
/*
* If we have an unprocessed orphan list hanging
* around from a previously readonly bdev mount,
sbi->s_mount_state = le16_to_cpu(es->s_state);
if ((err = ext4_group_extend(sb, es, n_blocks_count)))
goto restore_opts;
- if (!ext4_setup_super (sb, es, 0))
+ if (!ext4_setup_super(sb, es, 0))
sb->s_flags &= ~MS_RDONLY;
}
}
return err;
}
-static int ext4_statfs (struct dentry * dentry, struct kstatfs * buf)
+static int ext4_statfs(struct dentry *dentry, struct kstatfs *buf)
{
struct super_block *sb = dentry->d_sb;
struct ext4_sb_info *sbi = EXT4_SB(sb);
}
/* Journaling quota? */
if (EXT4_SB(sb)->s_qf_names[type]) {
- /* Quotafile not of fs root? */
+ /* Quotafile not in fs root? */
if (nd.path.dentry->d_parent->d_inode != sb->s_root->d_inode)
printk(KERN_WARNING
"EXT4-fs: Quota file not on filesystem root. "
"Journaled quota will not work.\n");
- }
+ }
/*
* When we journal data on quota file, we have to flush journal to see
jbd2_journal_unlock_updates(EXT4_SB(sb)->s_journal);
}
+ err = vfs_quota_on_path(sb, type, format_id, &nd.path);
path_put(&nd.path);
- return vfs_quota_on(sb, type, format_id, path, remount);
+ return err;
}
/* Read data from quotafile - avoid pagecache and such because we cannot afford
char *name = entry->e_name;
int n;
- for (n=0; n < entry->e_name_len; n++) {
+ for (n = 0; n < entry->e_name_len; n++) {
hash = (hash << NAME_HASH_SHIFT) ^
(hash >> (8*sizeof(hash) - NAME_HASH_SHIFT)) ^
*name++;
return 0;
}
+#define TIMES_SET_FLAGS (ATTR_MTIME_SET | ATTR_ATIME_SET | ATTR_TIMES_SET)
+
int fat_setattr(struct dentry *dentry, struct iattr *attr)
{
struct msdos_sb_info *sbi = MSDOS_SB(dentry->d_sb);
/* Check for setting the inode time. */
ia_valid = attr->ia_valid;
- if (ia_valid & (ATTR_MTIME_SET | ATTR_ATIME_SET)) {
+ if (ia_valid & TIMES_SET_FLAGS) {
if (fat_allow_set_time(sbi, inode))
- attr->ia_valid &= ~(ATTR_MTIME_SET | ATTR_ATIME_SET);
+ attr->ia_valid &= ~TIMES_SET_FLAGS;
}
error = inode_change_ok(inode, attr);
return res;
}
-/*
- * locate_fd finds a free file descriptor in the open_fds fdset,
- * expanding the fd arrays if necessary. Must be called with the
- * file_lock held for write.
- */
-
-static int locate_fd(unsigned int orig_start, int cloexec)
-{
- struct files_struct *files = current->files;
- unsigned int newfd;
- unsigned int start;
- int error;
- struct fdtable *fdt;
-
- spin_lock(&files->file_lock);
-repeat:
- fdt = files_fdtable(files);
- /*
- * Someone might have closed fd's in the range
- * orig_start..fdt->next_fd
- */
- start = orig_start;
- if (start < files->next_fd)
- start = files->next_fd;
-
- newfd = start;
- if (start < fdt->max_fds)
- newfd = find_next_zero_bit(fdt->open_fds->fds_bits,
- fdt->max_fds, start);
-
- error = expand_files(files, newfd);
- if (error < 0)
- goto out;
-
- /*
- * If we needed to expand the fs array we
- * might have blocked - try again.
- */
- if (error)
- goto repeat;
-
- if (start <= files->next_fd)
- files->next_fd = newfd + 1;
-
- FD_SET(newfd, fdt->open_fds);
- if (cloexec)
- FD_SET(newfd, fdt->close_on_exec);
- else
- FD_CLR(newfd, fdt->close_on_exec);
- error = newfd;
-
-out:
- spin_unlock(&files->file_lock);
- return error;
-}
-
-static int dupfd(struct file *file, unsigned int start, int cloexec)
-{
- int fd = locate_fd(start, cloexec);
- if (fd >= 0)
- fd_install(fd, file);
- else
- fput(file);
-
- return fd;
-}
-
asmlinkage long sys_dup3(unsigned int oldfd, unsigned int newfd, int flags)
{
int err = -EBADF;
return -EINVAL;
spin_lock(&files->file_lock);
- if (!(file = fcheck(oldfd)))
- goto out_unlock;
- get_file(file); /* We are now finished with oldfd */
-
err = expand_files(files, newfd);
+ file = fcheck(oldfd);
+ if (unlikely(!file))
+ goto Ebadf;
if (unlikely(err < 0)) {
if (err == -EMFILE)
- err = -EBADF;
- goto out_fput;
+ goto Ebadf;
+ goto out_unlock;
}
-
- /* To avoid races with open() and dup(), we will mark the fd as
- * in-use in the open-file bitmap throughout the entire dup2()
- * process. This is quite safe: do_close() uses the fd array
- * entry, not the bitmap, to decide what work needs to be
- * done. --sct */
- /* Doesn't work. open() might be there first. --AV */
-
- /* Yes. It's a race. In user space. Nothing sane to do */
+ /*
+ * We need to detect attempts to do dup2() over allocated but still
+ * not finished descriptor. NB: OpenBSD avoids that at the price of
+ * extra work in their equivalent of fget() - they insert struct
+ * file immediately after grabbing descriptor, mark it larval if
+ * more work (e.g. actual opening) is needed and make sure that
+ * fget() treats larval files as absent. Potentially interesting,
+ * but while extra work in fget() is trivial, locking implications
+ * and amount of surgery on open()-related paths in VFS are not.
+ * FreeBSD fails with -EBADF in the same situation, NetBSD "solution"
+ * deadlocks in rather amusing ways, AFAICS. All of that is out of
+ * scope of POSIX or SUS, since neither considers shared descriptor
+ * tables and this condition does not arise without those.
+ */
err = -EBUSY;
fdt = files_fdtable(files);
tofree = fdt->fd[newfd];
if (!tofree && FD_ISSET(newfd, fdt->open_fds))
- goto out_fput;
-
+ goto out_unlock;
+ get_file(file);
rcu_assign_pointer(fdt->fd[newfd], file);
FD_SET(newfd, fdt->open_fds);
if (flags & O_CLOEXEC)
if (tofree)
filp_close(tofree, files);
- err = newfd;
-out:
- return err;
-out_unlock:
- spin_unlock(&files->file_lock);
- goto out;
-out_fput:
+ return newfd;
+
+Ebadf:
+ err = -EBADF;
+out_unlock:
spin_unlock(&files->file_lock);
- fput(file);
- goto out;
+ return err;
}
asmlinkage long sys_dup2(unsigned int oldfd, unsigned int newfd)
asmlinkage long sys_dup(unsigned int fildes)
{
int ret = -EBADF;
- struct file * file = fget(fildes);
-
- if (file)
- ret = dupfd(file, 0, 0);
+ struct file *file = fget(fildes);
+
+ if (file) {
+ ret = get_unused_fd();
+ if (ret >= 0)
+ fd_install(ret, file);
+ else
+ fput(file);
+ }
return ret;
}
case F_DUPFD_CLOEXEC:
if (arg >= current->signal->rlim[RLIMIT_NOFILE].rlim_cur)
break;
- get_file(filp);
- err = dupfd(filp, arg, cmd == F_DUPFD_CLOEXEC);
+ err = alloc_fd(arg, cmd == F_DUPFD_CLOEXEC ? O_CLOEXEC : 0);
+ if (err >= 0) {
+ get_file(filp);
+ fd_install(err, filp);
+ }
break;
case F_GETFD:
err = get_close_on_exec(fd) ? FD_CLOEXEC : 0;
* Manage the dynamic fd arrays in the process files_struct.
*/
+#include <linux/module.h>
#include <linux/fs.h>
#include <linux/mm.h>
#include <linux/time.h>
},
.file_lock = __SPIN_LOCK_UNLOCKED(init_task.file_lock),
};
+
+/*
+ * allocate a file descriptor, mark it busy.
+ */
+int alloc_fd(unsigned start, unsigned flags)
+{
+ struct files_struct *files = current->files;
+ unsigned int fd;
+ int error;
+ struct fdtable *fdt;
+
+ spin_lock(&files->file_lock);
+repeat:
+ fdt = files_fdtable(files);
+ fd = start;
+ if (fd < files->next_fd)
+ fd = files->next_fd;
+
+ if (fd < fdt->max_fds)
+ fd = find_next_zero_bit(fdt->open_fds->fds_bits,
+ fdt->max_fds, fd);
+
+ error = expand_files(files, fd);
+ if (error < 0)
+ goto out;
+
+ /*
+ * If we needed to expand the fs array we
+ * might have blocked - try again.
+ */
+ if (error)
+ goto repeat;
+
+ if (start <= files->next_fd)
+ files->next_fd = fd + 1;
+
+ FD_SET(fd, fdt->open_fds);
+ if (flags & O_CLOEXEC)
+ FD_SET(fd, fdt->close_on_exec);
+ else
+ FD_CLR(fd, fdt->close_on_exec);
+ error = fd;
+#if 1
+ /* Sanity check */
+ if (rcu_dereference(fdt->fd[fd]) != NULL) {
+ printk(KERN_WARNING "alloc_fd: slot %d not NULL!\n", fd);
+ rcu_assign_pointer(fdt->fd[fd], NULL);
+ }
+#endif
+
+out:
+ spin_unlock(&files->file_lock);
+ return error;
+}
+
+int get_unused_fd(void)
+{
+ return alloc_fd(0, 0);
+}
+EXPORT_SYMBOL(get_unused_fd);
goto nope;
/* OK, it's a truncated page */
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto nope;
page_cache_get(page);
* blocking lock_buffer().
*/
if (buffer_dirty(bh)) {
- if (test_set_buffer_locked(bh)) {
+ if (!trylock_buffer(bh)) {
BUFFER_TRACE(bh, "needs blocking lock");
spin_unlock(&journal->j_list_lock);
/* Write out all data to prevent deadlocks */
spin_lock(&journal->j_list_lock);
}
if (unlikely(!buffer_uptodate(bh))) {
- if (TestSetPageLocked(bh->b_page)) {
+ if (!trylock_page(bh->b_page)) {
spin_unlock(&journal->j_list_lock);
lock_page(bh->b_page);
spin_lock(&journal->j_list_lock);
goto nope;
/* OK, it's a truncated page */
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto nope;
page_cache_get(page);
jinode->i_flags |= JI_COMMIT_RUNNING;
spin_unlock(&journal->j_list_lock);
err = filemap_fdatawait(jinode->i_vfs_inode->i_mapping);
- if (!ret)
- ret = err;
+ if (err) {
+ /*
+ * Because AS_EIO is cleared by
+ * wait_on_page_writeback_range(), set it again so
+ * that user process can get -EIO from fsync().
+ */
+ set_bit(AS_EIO,
+ &jinode->i_vfs_inode->i_mapping->flags);
+
+ if (!ret)
+ ret = err;
+ }
spin_lock(&journal->j_list_lock);
jinode->i_flags &= ~JI_COMMIT_RUNNING;
wake_up_bit(&jinode->i_flags, __JI_COMMIT_RUNNING);
* commit block, which happens below in such setting.
*/
err = journal_finish_inode_data_buffers(journal, commit_transaction);
- if (err)
- jbd2_journal_abort(journal, err);
+ if (err) {
+ char b[BDEVNAME_SIZE];
+
+ printk(KERN_WARNING
+ "JBD2: Detected IO errors while flushing file data "
+ "on %s\n", bdevname(journal->j_fs_dev, b));
+ err = 0;
+ }
/* Lo and behold: we have just managed to send a transaction to
the log. Before we can commit it, wait for the IO so far to
EXPORT_SYMBOL(jbd2_journal_create);
EXPORT_SYMBOL(jbd2_journal_load);
EXPORT_SYMBOL(jbd2_journal_destroy);
-EXPORT_SYMBOL(jbd2_journal_update_superblock);
EXPORT_SYMBOL(jbd2_journal_abort);
EXPORT_SYMBOL(jbd2_journal_errno);
EXPORT_SYMBOL(jbd2_journal_ack_err);
int jffs2_sum_init(struct jffs2_sb_info *c)
{
+ uint32_t sum_size = max_t(uint32_t, c->sector_size, MAX_SUMMARY_SIZE);
+
c->summary = kzalloc(sizeof(struct jffs2_summary), GFP_KERNEL);
if (!c->summary) {
return -ENOMEM;
}
- c->summary->sum_buf = vmalloc(c->sector_size);
+ c->summary->sum_buf = kmalloc(sum_size, GFP_KERNEL);
if (!c->summary->sum_buf) {
JFFS2_WARNING("Can't allocate buffer for writing out summary information!\n");
jffs2_sum_disable_collecting(c->summary);
- vfree(c->summary->sum_buf);
+ kfree(c->summary->sum_buf);
c->summary->sum_buf = NULL;
kfree(c->summary);
/* Write summary data to flash - helper function for jffs2_sum_write_sumnode() */
static int jffs2_sum_write_data(struct jffs2_sb_info *c, struct jffs2_eraseblock *jeb,
- uint32_t infosize, uint32_t datasize, int padsize)
+ uint32_t infosize, uint32_t datasize, int padsize)
{
struct jffs2_raw_summary isum;
union jffs2_sum_mem *temp;
int ret;
size_t retlen;
+ if (padsize + datasize > MAX_SUMMARY_SIZE) {
+ /* It won't fit in the buffer. Abort summary for this jeb */
+ jffs2_sum_disable_collecting(c->summary);
+
+ JFFS2_WARNING("Summary too big (%d data, %d pad) in eraseblock at %08x\n",
+ datasize, padsize, jeb->offset);
+ /* Non-fatal */
+ return 0;
+ }
+ /* Is there enough space for summary? */
+ if (padsize < 0) {
+ /* don't try to write out summary for this jeb */
+ jffs2_sum_disable_collecting(c->summary);
+
+ JFFS2_WARNING("Not enough space for summary, padsize = %d\n",
+ padsize);
+ /* Non-fatal */
+ return 0;
+ }
+
memset(c->summary->sum_buf, 0xff, datasize);
memset(&isum, 0, sizeof(isum));
{
int datasize, infosize, padsize;
struct jffs2_eraseblock *jeb;
- int ret;
+ int ret = 0;
dbg_summary("called\n");
infosize += padsize;
datasize += padsize;
- /* Is there enough space for summary? */
- if (padsize < 0) {
- /* don't try to write out summary for this jeb */
- jffs2_sum_disable_collecting(c->summary);
-
- JFFS2_WARNING("Not enough space for summary, padsize = %d\n", padsize);
- spin_lock(&c->erase_completion_lock);
- return 0;
- }
-
ret = jffs2_sum_write_data(c, jeb, infosize, datasize, padsize);
spin_lock(&c->erase_completion_lock);
return ret;
#ifndef JFFS2_SUMMARY_H
#define JFFS2_SUMMARY_H
+/* Limit summary size to 64KiB so that we can kmalloc it. If the summary
+ is larger than that, we have to just ditch it and avoid using summary
+ for the eraseblock in question... and it probably doesn't hurt us much
+ anyway. */
+#define MAX_SUMMARY_SIZE 65536
+
#include <linux/uio.h>
#include <linux/jffs2.h>
s->s_flags = MS_NOUSER;
s->s_maxbytes = ~0ULL;
- s->s_blocksize = 1024;
- s->s_blocksize_bits = 10;
+ s->s_blocksize = PAGE_SIZE;
+ s->s_blocksize_bits = PAGE_SHIFT;
s->s_magic = magic;
s->s_op = ops ? ops : &simple_super_operations;
s->s_time_gran = 1;
return retval;
return security_inode_permission(inode,
- mask & (MAY_READ|MAY_WRITE|MAY_EXEC));
+ mask & (MAY_READ|MAY_WRITE|MAY_EXEC|MAY_APPEND));
}
/**
* 3. We should have write and exec permissions on dir
* 4. We can't do it if dir is immutable (done in permission())
*/
-static inline int may_create(struct inode *dir, struct dentry *child,
- struct nameidata *nd)
+static inline int may_create(struct inode *dir, struct dentry *child)
{
if (child->d_inode)
return -EEXIST;
int vfs_create(struct inode *dir, struct dentry *dentry, int mode,
struct nameidata *nd)
{
- int error = may_create(dir, dentry, nd);
+ int error = may_create(dir, dentry);
if (error)
return error;
int vfs_mknod(struct inode *dir, struct dentry *dentry, int mode, dev_t dev)
{
- int error = may_create(dir, dentry, NULL);
+ int error = may_create(dir, dentry);
if (error)
return error;
int vfs_mkdir(struct inode *dir, struct dentry *dentry, int mode)
{
- int error = may_create(dir, dentry, NULL);
+ int error = may_create(dir, dentry);
if (error)
return error;
int vfs_symlink(struct inode *dir, struct dentry *dentry, const char *oldname)
{
- int error = may_create(dir, dentry, NULL);
+ int error = may_create(dir, dentry);
if (error)
return error;
if (!inode)
return -ENOENT;
- error = may_create(dir, new_dentry, NULL);
+ error = may_create(dir, new_dentry);
if (error)
return error;
return error;
if (!new_dentry->d_inode)
- error = may_create(new_dir, new_dentry, NULL);
+ error = may_create(new_dir, new_dentry);
else
error = may_delete(new_dir, new_dentry, is_dir);
if (error)
if (IS_ERR(mnt))
return PTR_ERR(mnt);
- return do_add_mount(mnt, nd, mnt_flags, NULL);
+ return do_add_mount(mnt, &nd->path, mnt_flags, NULL);
}
/*
* add a mount into a namespace's mount tree
* - provide the option of adding the new mount to an expiration list
*/
-int do_add_mount(struct vfsmount *newmnt, struct nameidata *nd,
+int do_add_mount(struct vfsmount *newmnt, struct path *path,
int mnt_flags, struct list_head *fslist)
{
int err;
down_write(&namespace_sem);
/* Something was mounted here while we slept */
- while (d_mountpoint(nd->path.dentry) &&
- follow_down(&nd->path.mnt, &nd->path.dentry))
+ while (d_mountpoint(path->dentry) &&
+ follow_down(&path->mnt, &path->dentry))
;
err = -EINVAL;
- if (!check_mnt(nd->path.mnt))
+ if (!check_mnt(path->mnt))
goto unlock;
/* Refuse the same filesystem on the same mount point */
err = -EBUSY;
- if (nd->path.mnt->mnt_sb == newmnt->mnt_sb &&
- nd->path.mnt->mnt_root == nd->path.dentry)
+ if (path->mnt->mnt_sb == newmnt->mnt_sb &&
+ path->mnt->mnt_root == path->dentry)
goto unlock;
err = -EINVAL;
goto unlock;
newmnt->mnt_flags = mnt_flags;
- if ((err = graft_tree(newmnt, &nd->path)))
+ if ((err = graft_tree(newmnt, path)))
goto unlock;
if (fslist) /* add to the specified expiration list */
goto out_err;
mntget(mnt);
- err = do_add_mount(mnt, nd, nd->path.mnt->mnt_flags|MNT_SHRINKABLE,
+ err = do_add_mount(mnt, &nd->path, nd->path.mnt->mnt_flags|MNT_SHRINKABLE,
&nfs_automount_list);
if (err < 0) {
mntput(mnt);
Opt_err
};
-static match_table_t __initconst tokens = {
+static match_table_t __initdata tokens = {
{Opt_port, "port=%u"},
{Opt_rsize, "rsize=%u"},
{Opt_wsize, "wsize=%u"},
static struct nfsd4_operation nfsd4_ops[];
-static inline char *nfsd4_op_name(unsigned opnum);
+static const char *nfsd4_op_name(unsigned opnum);
/*
* COMPOUND call.
},
};
-static inline char *
-nfsd4_op_name(unsigned opnum)
+static const char *nfsd4_op_name(unsigned opnum)
{
if (opnum < ARRAY_SIZE(nfsd4_ops))
return nfsd4_ops[opnum].op_name;
tbh = bhs[i];
if (!tbh)
continue;
- if (unlikely(test_set_buffer_locked(tbh)))
+ if (!trylock_buffer(tbh))
BUG();
/* The buffer dirty state is now irrelevant, just clean it. */
clear_buffer_dirty(tbh);
for (i = 0; i < nr_bhs; i++) {
struct buffer_head *tbh = bhs[i];
- if (unlikely(test_set_buffer_locked(tbh)))
+ if (!trylock_buffer(tbh))
continue;
if (unlikely(buffer_uptodate(tbh))) {
unlock_buffer(tbh);
for (i_bhs = 0; i_bhs < nr_bhs; i_bhs++) {
struct buffer_head *tbh = bhs[i_bhs];
- if (unlikely(test_set_buffer_locked(tbh)))
+ if (!trylock_buffer(tbh))
BUG();
BUG_ON(!buffer_uptodate(tbh));
clear_buffer_dirty(tbh);
for (i_bhs = 0; i_bhs < nr_bhs; i_bhs++) {
struct buffer_head *tbh = bhs[i_bhs];
- if (unlikely(test_set_buffer_locked(tbh)))
+ if (!trylock_buffer(tbh))
BUG();
BUG_ON(!buffer_uptodate(tbh));
clear_buffer_dirty(tbh);
for(i = 0; i < wc->w_num_pages; i++) {
tmppage = wc->w_pages[i];
- if (ocfs2_should_order_data(inode))
- walk_page_buffers(wc->w_handle, page_buffers(tmppage),
- from, to, NULL,
- ocfs2_journal_dirty_data);
-
- block_commit_write(tmppage, from, to);
+ if (page_has_buffers(tmppage)) {
+ if (ocfs2_should_order_data(inode))
+ walk_page_buffers(wc->w_handle,
+ page_buffers(tmppage),
+ from, to, NULL,
+ ocfs2_journal_dirty_data);
+
+ block_commit_write(tmppage, from, to);
+ }
}
}
to = PAGE_CACHE_SIZE;
}
- if (ocfs2_should_order_data(inode))
- walk_page_buffers(wc->w_handle, page_buffers(tmppage),
- from, to, NULL,
- ocfs2_journal_dirty_data);
-
- block_commit_write(tmppage, from, to);
+ if (page_has_buffers(tmppage)) {
+ if (ocfs2_should_order_data(inode))
+ walk_page_buffers(wc->w_handle,
+ page_buffers(tmppage),
+ from, to, NULL,
+ ocfs2_journal_dirty_data);
+ block_commit_write(tmppage, from, to);
+ }
}
out_write_size:
out_rw_unlock:
ocfs2_rw_unlock(inode, 1);
- mutex_unlock(&inode->i_mutex);
out:
+ mutex_unlock(&inode->i_mutex);
return ret;
}
static int ocfs2_commit_cache(struct ocfs2_super *osb);
static int ocfs2_wait_on_mount(struct ocfs2_super *osb);
static int ocfs2_journal_toggle_dirty(struct ocfs2_super *osb,
- int dirty);
+ int dirty, int replayed);
static int ocfs2_trylock_journal(struct ocfs2_super *osb,
int slot_num);
static int ocfs2_recover_orphans(struct ocfs2_super *osb,
return status;
}
+static void ocfs2_bump_recovery_generation(struct ocfs2_dinode *di)
+{
+ le32_add_cpu(&(di->id1.journal1.ij_recovery_generation), 1);
+}
+
+static u32 ocfs2_get_recovery_generation(struct ocfs2_dinode *di)
+{
+ return le32_to_cpu(di->id1.journal1.ij_recovery_generation);
+}
+
static int ocfs2_journal_toggle_dirty(struct ocfs2_super *osb,
- int dirty)
+ int dirty, int replayed)
{
int status;
unsigned int flags;
flags &= ~OCFS2_JOURNAL_DIRTY_FL;
fe->id1.journal1.ij_flags = cpu_to_le32(flags);
+ if (replayed)
+ ocfs2_bump_recovery_generation(fe);
+
status = ocfs2_write_block(osb, bh, journal->j_inode);
if (status < 0)
mlog_errno(status);
* Do not toggle if flush was unsuccessful otherwise
* will leave dirty metadata in a "clean" journal
*/
- status = ocfs2_journal_toggle_dirty(osb, 0);
+ status = ocfs2_journal_toggle_dirty(osb, 0, 0);
if (status < 0)
mlog_errno(status);
}
}
}
-int ocfs2_journal_load(struct ocfs2_journal *journal, int local)
+int ocfs2_journal_load(struct ocfs2_journal *journal, int local, int replayed)
{
int status = 0;
struct ocfs2_super *osb;
ocfs2_clear_journal_error(osb->sb, journal->j_journal, osb->slot_num);
- status = ocfs2_journal_toggle_dirty(osb, 1);
+ status = ocfs2_journal_toggle_dirty(osb, 1, replayed);
if (status < 0) {
mlog_errno(status);
goto done;
goto bail;
}
- status = ocfs2_journal_toggle_dirty(journal->j_osb, 0);
+ status = ocfs2_journal_toggle_dirty(journal->j_osb, 0, 0);
if (status < 0)
mlog_errno(status);
spin_unlock(&osb->osb_lock);
mlog(0, "All nodes recovered\n");
+ /* Refresh all journal recovery generations from disk */
+ status = ocfs2_check_journals_nolocks(osb);
+ status = (status == -EROFS) ? 0 : status;
+ if (status < 0)
+ mlog_errno(status);
+
ocfs2_super_unlock(osb, 1);
/* We always run recovery on our own orphan dir - the dead
mlog_exit_void();
}
+static int ocfs2_read_journal_inode(struct ocfs2_super *osb,
+ int slot_num,
+ struct buffer_head **bh,
+ struct inode **ret_inode)
+{
+ int status = -EACCES;
+ struct inode *inode = NULL;
+
+ BUG_ON(slot_num >= osb->max_slots);
+
+ inode = ocfs2_get_system_file_inode(osb, JOURNAL_SYSTEM_INODE,
+ slot_num);
+ if (!inode || is_bad_inode(inode)) {
+ mlog_errno(status);
+ goto bail;
+ }
+ SET_INODE_JOURNAL(inode);
+
+ status = ocfs2_read_block(osb, OCFS2_I(inode)->ip_blkno, bh, 0, inode);
+ if (status < 0) {
+ mlog_errno(status);
+ goto bail;
+ }
+
+ status = 0;
+
+bail:
+ if (inode) {
+ if (status || !ret_inode)
+ iput(inode);
+ else
+ *ret_inode = inode;
+ }
+ return status;
+}
+
/* Does the actual journal replay and marks the journal inode as
* clean. Will only replay if the journal inode is marked dirty. */
static int ocfs2_replay_journal(struct ocfs2_super *osb,
struct ocfs2_dinode *fe;
journal_t *journal = NULL;
struct buffer_head *bh = NULL;
+ u32 slot_reco_gen;
- inode = ocfs2_get_system_file_inode(osb, JOURNAL_SYSTEM_INODE,
- slot_num);
- if (inode == NULL) {
- status = -EACCES;
+ status = ocfs2_read_journal_inode(osb, slot_num, &bh, &inode);
+ if (status) {
mlog_errno(status);
goto done;
}
- if (is_bad_inode(inode)) {
- status = -EACCES;
- iput(inode);
- inode = NULL;
- mlog_errno(status);
+
+ fe = (struct ocfs2_dinode *)bh->b_data;
+ slot_reco_gen = ocfs2_get_recovery_generation(fe);
+ brelse(bh);
+ bh = NULL;
+
+ /*
+ * As the fs recovery is asynchronous, there is a small chance that
+ * another node mounted (and recovered) the slot before the recovery
+ * thread could get the lock. To handle that, we dirty read the journal
+ * inode for that slot to get the recovery generation. If it is
+ * different than what we expected, the slot has been recovered.
+ * If not, it needs recovery.
+ */
+ if (osb->slot_recovery_generations[slot_num] != slot_reco_gen) {
+ mlog(0, "Slot %u already recovered (old/new=%u/%u)\n", slot_num,
+ osb->slot_recovery_generations[slot_num], slot_reco_gen);
+ osb->slot_recovery_generations[slot_num] = slot_reco_gen;
+ status = -EBUSY;
goto done;
}
- SET_INODE_JOURNAL(inode);
+
+ /* Continue with recovery as the journal has not yet been recovered */
status = ocfs2_inode_lock_full(inode, &bh, 1, OCFS2_META_LOCK_RECOVERY);
if (status < 0) {
fe = (struct ocfs2_dinode *) bh->b_data;
flags = le32_to_cpu(fe->id1.journal1.ij_flags);
+ slot_reco_gen = ocfs2_get_recovery_generation(fe);
if (!(flags & OCFS2_JOURNAL_DIRTY_FL)) {
mlog(0, "No recovery required for node %d\n", node_num);
+ /* Refresh recovery generation for the slot */
+ osb->slot_recovery_generations[slot_num] = slot_reco_gen;
goto done;
}
flags &= ~OCFS2_JOURNAL_DIRTY_FL;
fe->id1.journal1.ij_flags = cpu_to_le32(flags);
+ /* Increment recovery generation to indicate successful recovery */
+ ocfs2_bump_recovery_generation(fe);
+ osb->slot_recovery_generations[slot_num] =
+ ocfs2_get_recovery_generation(fe);
+
status = ocfs2_write_block(osb, bh, inode);
if (status < 0)
mlog_errno(status);
status = ocfs2_replay_journal(osb, node_num, slot_num);
if (status < 0) {
+ if (status == -EBUSY) {
+ mlog(0, "Skipping recovery for slot %u (node %u) "
+ "as another node has recovered it\n", slot_num,
+ node_num);
+ status = 0;
+ goto done;
+ }
mlog_errno(status);
goto done;
}
{
unsigned int node_num;
int status, i;
+ struct buffer_head *bh = NULL;
+ struct ocfs2_dinode *di;
/* This is called with the super block cluster lock, so we
* know that the slot map can't change underneath us. */
spin_lock(&osb->osb_lock);
for (i = 0; i < osb->max_slots; i++) {
+ /* Read journal inode to get the recovery generation */
+ status = ocfs2_read_journal_inode(osb, i, &bh, NULL);
+ if (status) {
+ mlog_errno(status);
+ goto bail;
+ }
+ di = (struct ocfs2_dinode *)bh->b_data;
+ osb->slot_recovery_generations[i] =
+ ocfs2_get_recovery_generation(di);
+ brelse(bh);
+ bh = NULL;
+
+ mlog(0, "Slot %u recovery generation is %u\n", i,
+ osb->slot_recovery_generations[i]);
+
if (i == osb->slot_num)
continue;
return 0;
}
-/* Look for a dirty journal without taking any cluster locks. Used for
- * hard readonly access to determine whether the file system journals
- * require recovery. */
+/* Reads all the journal inodes without taking any cluster locks. Used
+ * for hard readonly access to determine whether any journal requires
+ * recovery. Also used to refresh the recovery generation numbers after
+ * a journal has been recovered by another node.
+ */
int ocfs2_check_journals_nolocks(struct ocfs2_super *osb)
{
int ret = 0;
unsigned int slot;
- struct buffer_head *di_bh;
+ struct buffer_head *di_bh = NULL;
struct ocfs2_dinode *di;
- struct inode *journal = NULL;
+ int journal_dirty = 0;
for(slot = 0; slot < osb->max_slots; slot++) {
- journal = ocfs2_get_system_file_inode(osb,
- JOURNAL_SYSTEM_INODE,
- slot);
- if (!journal || is_bad_inode(journal)) {
- ret = -EACCES;
- mlog_errno(ret);
- goto out;
- }
-
- di_bh = NULL;
- ret = ocfs2_read_block(osb, OCFS2_I(journal)->ip_blkno, &di_bh,
- 0, journal);
- if (ret < 0) {
+ ret = ocfs2_read_journal_inode(osb, slot, &di_bh, NULL);
+ if (ret) {
mlog_errno(ret);
goto out;
}
di = (struct ocfs2_dinode *) di_bh->b_data;
+ osb->slot_recovery_generations[slot] =
+ ocfs2_get_recovery_generation(di);
+
if (le32_to_cpu(di->id1.journal1.ij_flags) &
OCFS2_JOURNAL_DIRTY_FL)
- ret = -EROFS;
+ journal_dirty = 1;
brelse(di_bh);
- if (ret)
- break;
+ di_bh = NULL;
}
out:
- if (journal)
- iput(journal);
-
+ if (journal_dirty)
+ ret = -EROFS;
return ret;
}
void ocfs2_journal_shutdown(struct ocfs2_super *osb);
int ocfs2_journal_wipe(struct ocfs2_journal *journal,
int full);
-int ocfs2_journal_load(struct ocfs2_journal *journal, int local);
+int ocfs2_journal_load(struct ocfs2_journal *journal, int local,
+ int replayed);
int ocfs2_check_journals_nolocks(struct ocfs2_super *osb);
void ocfs2_recovery_thread(struct ocfs2_super *osb,
int node_num);
struct ocfs2_slot_info *slot_info;
+ u32 *slot_recovery_generations;
+
spinlock_t node_map_lock;
u64 root_blkno;
struct { /* Info for journal system
inodes */
__le32 ij_flags; /* Mounted, version, etc. */
- __le32 ij_pad;
+ __le32 ij_recovery_generation; /* Incremented when the
+ journal is recovered
+ after an unclean
+ shutdown */
} journal1;
} id1; /* Inode type dependant 1 */
/*C0*/ union {
}
mlog(0, "max_slots for this device: %u\n", osb->max_slots);
+ osb->slot_recovery_generations =
+ kcalloc(osb->max_slots, sizeof(*osb->slot_recovery_generations),
+ GFP_KERNEL);
+ if (!osb->slot_recovery_generations) {
+ status = -ENOMEM;
+ mlog_errno(status);
+ goto bail;
+ }
+
init_waitqueue_head(&osb->osb_wipe_event);
osb->osb_orphan_wipes = kcalloc(osb->max_slots,
sizeof(*osb->osb_orphan_wipes),
local = ocfs2_mount_local(osb);
/* will play back anything left in the journal. */
- status = ocfs2_journal_load(osb->journal, local);
+ status = ocfs2_journal_load(osb->journal, local, dirty);
if (status < 0) {
mlog(ML_ERROR, "ocfs2 journal load failed! %d\n", status);
goto finally;
ocfs2_free_slot_info(osb);
kfree(osb->osb_orphan_wipes);
+ kfree(osb->slot_recovery_generations);
/* FIXME
* This belongs in journal shutdown, but because we have to
* allocate osb->journal at the start of ocfs2_initalize_osb(),
}
if (set) {
set_bit(bit, sbi->s_imap[map]);
- set_bit(bit, (long *) bh->b_data);
+ set_bit(bit, (unsigned long *)bh->b_data);
} else {
clear_bit(bit, sbi->s_imap[map]);
- clear_bit(bit, (long *) bh->b_data);
+ clear_bit(bit, (unsigned long *)bh->b_data);
}
}
mark_buffer_dirty(bh);
if (!bh)
goto out;
- set_bit(bit, (long *) bh->b_data);
+ set_bit(bit, (unsigned long *)bh->b_data);
mark_buffer_dirty(bh);
brelse(bh);
}
oi = (struct omfs_inode *) bh->b_data;
oi->i_head.h_self = cpu_to_be64(inode->i_ino);
- oi->i_sibling = ~0ULL;
+ oi->i_sibling = ~cpu_to_be64(0ULL);
mark_buffer_dirty(bh);
brelse(bh);
{
struct omfs_extent *oe = (struct omfs_extent *) &bh->b_data[offset];
- oe->e_next = ~0ULL;
+ oe->e_next = ~cpu_to_be64(0ULL);
oe->e_extent_count = cpu_to_be32(1),
oe->e_fill = cpu_to_be32(0x22),
- oe->e_entry.e_cluster = ~0ULL;
- oe->e_entry.e_blocks = ~0ULL;
+ oe->e_entry.e_cluster = ~cpu_to_be64(0ULL);
+ oe->e_entry.e_blocks = ~cpu_to_be64(0ULL);
}
int omfs_shrink_inode(struct inode *inode)
if (sbi->s_num_blocks != be64_to_cpu(omfs_rb->r_num_blocks)) {
printk(KERN_ERR "omfs: block count discrepancy between "
"super and root blocks (%llx, %llx)\n",
- sbi->s_num_blocks, be64_to_cpu(omfs_rb->r_num_blocks));
+ (unsigned long long)sbi->s_num_blocks,
+ (unsigned long long)be64_to_cpu(omfs_rb->r_num_blocks));
goto out_brelse_bh2;
}
}
EXPORT_SYMBOL(dentry_open);
-/*
- * Find an empty file descriptor entry, and mark it busy.
- */
-int get_unused_fd_flags(int flags)
-{
- struct files_struct * files = current->files;
- int fd, error;
- struct fdtable *fdt;
-
- spin_lock(&files->file_lock);
-
-repeat:
- fdt = files_fdtable(files);
- fd = find_next_zero_bit(fdt->open_fds->fds_bits, fdt->max_fds,
- files->next_fd);
-
- /* Do we need to expand the fd array or fd set? */
- error = expand_files(files, fd);
- if (error < 0)
- goto out;
-
- if (error) {
- /*
- * If we needed to expand the fs array we
- * might have blocked - try again.
- */
- goto repeat;
- }
-
- FD_SET(fd, fdt->open_fds);
- if (flags & O_CLOEXEC)
- FD_SET(fd, fdt->close_on_exec);
- else
- FD_CLR(fd, fdt->close_on_exec);
- files->next_fd = fd + 1;
-#if 1
- /* Sanity check */
- if (fdt->fd[fd] != NULL) {
- printk(KERN_WARNING "get_unused_fd: slot %d not NULL!\n", fd);
- fdt->fd[fd] = NULL;
- }
-#endif
- error = fd;
-
-out:
- spin_unlock(&files->file_lock);
- return error;
-}
-
-int get_unused_fd(void)
-{
- return get_unused_fd_flags(0);
-}
-
-EXPORT_SYMBOL(get_unused_fd);
-
static void __put_unused_fd(struct files_struct *files, unsigned int fd)
{
struct fdtable *fdt = files_fdtable(files);
"read_bytes: %llu\n"
"write_bytes: %llu\n"
"cancelled_write_bytes: %llu\n",
- acct.rchar, acct.wchar,
- acct.syscr, acct.syscw,
- acct.read_bytes, acct.write_bytes,
- acct.cancelled_write_bytes);
+ (unsigned long long)acct.rchar,
+ (unsigned long long)acct.wchar,
+ (unsigned long long)acct.syscr,
+ (unsigned long long)acct.syscw,
+ (unsigned long long)acct.read_bytes,
+ (unsigned long long)acct.write_bytes,
+ (unsigned long long)acct.cancelled_write_bytes);
}
static int proc_tid_io_accounting(struct task_struct *task, char *buffer)
return rtn;
}
-static DEFINE_IDR(proc_inum_idr);
+static DEFINE_IDA(proc_inum_ida);
static DEFINE_SPINLOCK(proc_inum_lock); /* protects the above */
-#define PROC_DYNAMIC_FIRST 0xF0000000UL
+#define PROC_DYNAMIC_FIRST 0xF0000000U
/*
* Return an inode number between PROC_DYNAMIC_FIRST and
*/
static unsigned int get_inode_number(void)
{
- int i, inum = 0;
+ unsigned int i;
int error;
retry:
- if (idr_pre_get(&proc_inum_idr, GFP_KERNEL) == 0)
+ if (ida_pre_get(&proc_inum_ida, GFP_KERNEL) == 0)
return 0;
spin_lock(&proc_inum_lock);
- error = idr_get_new(&proc_inum_idr, NULL, &i);
+ error = ida_get_new(&proc_inum_ida, &i);
spin_unlock(&proc_inum_lock);
if (error == -EAGAIN)
goto retry;
else if (error)
return 0;
- inum = (i & MAX_ID_MASK) + PROC_DYNAMIC_FIRST;
-
- /* inum will never be more than 0xf0ffffff, so no check
- * for overflow.
- */
-
- return inum;
+ if (i > UINT_MAX - PROC_DYNAMIC_FIRST) {
+ spin_lock(&proc_inum_lock);
+ ida_remove(&proc_inum_ida, i);
+ spin_unlock(&proc_inum_lock);
+ }
+ return PROC_DYNAMIC_FIRST + i;
}
static void release_inode_number(unsigned int inum)
{
- int id = (inum - PROC_DYNAMIC_FIRST) | ~MAX_ID_MASK;
-
spin_lock(&proc_inum_lock);
- idr_remove(&proc_inum_idr, id);
+ ida_remove(&proc_inum_ida, inum - PROC_DYNAMIC_FIRST);
spin_unlock(&proc_inum_lock);
}
if (wbc->sync_mode != WB_SYNC_NONE || !wbc->nonblocking) {
lock_buffer(bh);
} else {
- if (test_set_buffer_locked(bh)) {
+ if (!trylock_buffer(bh)) {
redirty_page_for_writepage(wbc, page);
continue;
}
static void release_buffer_page(struct buffer_head *bh)
{
struct page *page = bh->b_page;
- if (!page->mapping && !TestSetPageLocked(page)) {
+ if (!page->mapping && trylock_page(page)) {
page_cache_get(page);
put_bh(bh);
if (!page->mapping)
jh = JH_ENTRY(list->next);
bh = jh->bh;
get_bh(bh);
- if (test_set_buffer_locked(bh)) {
+ if (!trylock_buffer(bh)) {
if (!buffer_dirty(bh)) {
list_move(&jh->list, &tmp);
goto loop_next;
{
PROC_INFO_INC(p_s_sb, journal.prepare);
- if (test_set_buffer_locked(bh)) {
+ if (!trylock_buffer(bh)) {
if (!wait)
return 0;
lock_buffer(bh);
return err;
/* Quotafile not on the same filesystem? */
if (nd.path.mnt->mnt_sb != sb) {
- path_put(&nd.path);
- return -EXDEV;
+ err = -EXDEV;
+ goto out;
}
inode = nd.path.dentry->d_inode;
/* We must not pack tails for quota files on reiserfs for quota IO to work */
reiserfs_warning(sb,
"reiserfs: Unpacking tail of quota file failed"
" (%d). Cannot turn on quotas.", err);
- path_put(&nd.path);
- return -EINVAL;
+ err = -EINVAL;
+ goto out;
}
mark_inode_dirty(inode);
}
/* Just start temporary transaction and finish it */
err = journal_begin(&th, sb, 1);
if (err)
- return err;
+ goto out;
err = journal_end_sync(&th, sb, 1);
if (err)
- return err;
+ goto out;
}
+ err = vfs_quota_on_path(sb, type, format_id, &nd.path);
+out:
path_put(&nd.path);
- return vfs_quota_on(sb, type, format_id, path, 0);
+ return err;
}
/* Read data from quotafile - avoid pagecache and such because we cannot afford
romfs_readpage(struct file *file, struct page * page)
{
struct inode *inode = page->mapping->host;
- loff_t offset, avail, readlen;
+ loff_t offset, size;
+ unsigned long filled;
void *buf;
int result = -EIO;
/* 32 bit warning -- but not for us :) */
offset = page_offset(page);
- if (offset < i_size_read(inode)) {
- avail = inode->i_size-offset;
- readlen = min_t(unsigned long, avail, PAGE_SIZE);
- if (romfs_copyfrom(inode, buf, ROMFS_I(inode)->i_dataoffset+offset, readlen) == readlen) {
- if (readlen < PAGE_SIZE) {
- memset(buf + readlen,0,PAGE_SIZE-readlen);
- }
- SetPageUptodate(page);
- result = 0;
+ size = i_size_read(inode);
+ filled = 0;
+ result = 0;
+ if (offset < size) {
+ unsigned long readlen;
+
+ size -= offset;
+ readlen = size > PAGE_SIZE ? PAGE_SIZE : size;
+
+ filled = romfs_copyfrom(inode, buf, ROMFS_I(inode)->i_dataoffset+offset, readlen);
+
+ if (filled != readlen) {
+ SetPageError(page);
+ filled = 0;
+ result = -EIO;
}
}
- if (result) {
- memset(buf, 0, PAGE_SIZE);
- SetPageError(page);
- }
+
+ if (filled < PAGE_SIZE)
+ memset(buf + filled, 0, PAGE_SIZE-filled);
+
+ if (!result)
+ SetPageUptodate(page);
flush_dcache_page(page);
unlock_page(page);
* for an in-flight io page
*/
if (flags & SPLICE_F_NONBLOCK) {
- if (TestSetPageLocked(page)) {
+ if (!trylock_page(page)) {
error = -EAGAIN;
break;
}
{
struct ufs_sb_info *sbi = UFS_SB(vfs->mnt_sb);
unsigned mval = sbi->s_mount_opt & UFS_MOUNT_UFSTYPE;
- const struct match_token *tp = tokens;
+ struct match_token *tp = tokens;
while (tp->token != Opt_onerror_panic && tp->token != mval)
++tp;
xfs_iops.o \
xfs_lrw.o \
xfs_super.o \
- xfs_vnode.o)
+ xfs_vnode.o \
+ xfs_xattr.o)
# Objects in support/
xfs-y += $(addprefix support/, \
}
void
-kmem_free(void *ptr, size_t size)
+kmem_free(const void *ptr)
{
if (!is_vmalloc_addr(ptr)) {
kfree(ptr);
}
void *
-kmem_realloc(void *ptr, size_t newsize, size_t oldsize,
+kmem_realloc(const void *ptr, size_t newsize, size_t oldsize,
unsigned int __nocast flags)
{
void *new;
if (new)
memcpy(new, ptr,
((oldsize < newsize) ? oldsize : newsize));
- kmem_free(ptr, oldsize);
+ kmem_free(ptr);
}
return new;
}
extern void *kmem_alloc(size_t, unsigned int __nocast);
extern void *kmem_zalloc(size_t, unsigned int __nocast);
extern void *kmem_zalloc_greedy(size_t *, size_t, size_t, unsigned int __nocast);
-extern void *kmem_realloc(void *, size_t, size_t, unsigned int __nocast);
-extern void kmem_free(void *, size_t);
+extern void *kmem_realloc(const void *, size_t, size_t, unsigned int __nocast);
+extern void kmem_free(const void *);
/*
* Zone interfaces
STATIC void
xfs_start_page_writeback(
struct page *page,
- struct writeback_control *wbc,
int clear_dirty,
int buffers)
{
} else
pg_offset = PAGE_CACHE_SIZE;
- if (page->index == tindex && !TestSetPageLocked(page)) {
+ if (page->index == tindex && trylock_page(page)) {
pg_len = xfs_probe_page(page, pg_offset, mapped);
unlock_page(page);
}
if (page->index != tindex)
goto fail;
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto fail;
if (PageWriteback(page))
goto fail_unlock_page;
done = 1;
}
}
- xfs_start_page_writeback(page, wbc, !page_dirty, count);
+ xfs_start_page_writeback(page, !page_dirty, count);
}
return done;
* that we are writing into for the first time.
*/
type = IOMAP_NEW;
- if (!test_and_set_bit(BH_Lock, &bh->b_state)) {
+ if (trylock_buffer(bh)) {
ASSERT(buffer_mapped(bh));
if (iomap_valid)
all_bh = 1;
SetPageUptodate(page);
if (startio)
- xfs_start_page_writeback(page, wbc, 1, count);
+ xfs_start_page_writeback(page, 1, count);
if (ioend && iomap_valid) {
offset = (iomap.iomap_offset + iomap.iomap_bsize - 1) >>
xfs_buf_t *bp)
{
if (bp->b_pages != bp->b_page_array) {
- kmem_free(bp->b_pages,
- bp->b_page_count * sizeof(struct page *));
+ kmem_free(bp->b_pages);
}
}
xfs_free_bufhash(
xfs_buftarg_t *btp)
{
- kmem_free(btp->bt_hash, (1<<btp->bt_hashshift) * sizeof(xfs_bufhash_t));
+ kmem_free(btp->bt_hash);
btp->bt_hash = NULL;
}
void
xfs_free_buftarg(
- xfs_buftarg_t *btp,
- int external)
+ xfs_buftarg_t *btp)
{
xfs_flush_buftarg(btp, 1);
xfs_blkdev_issue_flush(btp);
- if (external)
- xfs_blkdev_put(btp->bt_bdev);
xfs_free_bufhash(btp);
iput(btp->bt_mapping->host);
xfs_unregister_buftarg(btp);
kthread_stop(btp->bt_task);
- kmem_free(btp, sizeof(*btp));
+ kmem_free(btp);
}
STATIC int
return btp;
error:
- kmem_free(btp, sizeof(*btp));
+ kmem_free(btp);
return NULL;
}
* Handling of buftargs.
*/
extern xfs_buftarg_t *xfs_alloc_buftarg(struct block_device *, int);
-extern void xfs_free_buftarg(xfs_buftarg_t *, int);
+extern void xfs_free_buftarg(xfs_buftarg_t *);
extern void xfs_wait_buftarg(xfs_buftarg_t *);
extern int xfs_setsize_buftarg(xfs_buftarg_t *, unsigned int, unsigned int);
extern int xfs_flush_buftarg(xfs_buftarg_t *, int);
struct xfs_inode *cip;
struct dentry *parent;
- error = xfs_lookup(XFS_I(child->d_inode), &xfs_name_dotdot, &cip);
+ error = xfs_lookup(XFS_I(child->d_inode), &xfs_name_dotdot, &cip, NULL);
if (unlikely(error))
return ERR_PTR(-error);
#include "xfs_dfrag.h"
#include "xfs_fsops.h"
#include "xfs_vnodeops.h"
+#include "xfs_quota.h"
+#include "xfs_inode_item.h"
#include <linux/capability.h>
#include <linux/dcache.h>
if (al_hreq.buflen > XATTR_LIST_MAX)
return -XFS_ERROR(EINVAL);
+ /*
+ * Reject flags, only allow namespaces.
+ */
+ if (al_hreq.flags & ~(ATTR_ROOT | ATTR_SECURE))
+ return -XFS_ERROR(EINVAL);
+
error = xfs_vget_fsop_handlereq(mp, parinode, &al_hreq.hreq, &inode);
if (error)
goto out;
goto out;
error = E2BIG;
- size = am_hreq.opcount * sizeof(attr_multiop_t);
+ size = am_hreq.opcount * sizeof(xfs_attr_multiop_t);
if (!size || size > 16 * PAGE_SIZE)
goto out_vn_rele;
return -XFS_ERROR(EFAULT);
if (filp->f_flags & (O_NDELAY|O_NONBLOCK))
- attr_flags |= ATTR_NONBLOCK;
+ attr_flags |= XFS_ATTR_NONBLOCK;
if (ioflags & IO_INVIS)
- attr_flags |= ATTR_DMI;
+ attr_flags |= XFS_ATTR_DMI;
error = xfs_change_file_space(ip, cmd, &bf, filp->f_pos,
NULL, attr_flags);
return 0;
}
+STATIC void
+xfs_set_diflags(
+ struct xfs_inode *ip,
+ unsigned int xflags)
+{
+ unsigned int di_flags;
+
+ /* can't set PREALLOC this way, just preserve it */
+ di_flags = (ip->i_d.di_flags & XFS_DIFLAG_PREALLOC);
+ if (xflags & XFS_XFLAG_IMMUTABLE)
+ di_flags |= XFS_DIFLAG_IMMUTABLE;
+ if (xflags & XFS_XFLAG_APPEND)
+ di_flags |= XFS_DIFLAG_APPEND;
+ if (xflags & XFS_XFLAG_SYNC)
+ di_flags |= XFS_DIFLAG_SYNC;
+ if (xflags & XFS_XFLAG_NOATIME)
+ di_flags |= XFS_DIFLAG_NOATIME;
+ if (xflags & XFS_XFLAG_NODUMP)
+ di_flags |= XFS_DIFLAG_NODUMP;
+ if (xflags & XFS_XFLAG_PROJINHERIT)
+ di_flags |= XFS_DIFLAG_PROJINHERIT;
+ if (xflags & XFS_XFLAG_NODEFRAG)
+ di_flags |= XFS_DIFLAG_NODEFRAG;
+ if (xflags & XFS_XFLAG_FILESTREAM)
+ di_flags |= XFS_DIFLAG_FILESTREAM;
+ if ((ip->i_d.di_mode & S_IFMT) == S_IFDIR) {
+ if (xflags & XFS_XFLAG_RTINHERIT)
+ di_flags |= XFS_DIFLAG_RTINHERIT;
+ if (xflags & XFS_XFLAG_NOSYMLINKS)
+ di_flags |= XFS_DIFLAG_NOSYMLINKS;
+ if (xflags & XFS_XFLAG_EXTSZINHERIT)
+ di_flags |= XFS_DIFLAG_EXTSZINHERIT;
+ } else if ((ip->i_d.di_mode & S_IFMT) == S_IFREG) {
+ if (xflags & XFS_XFLAG_REALTIME)
+ di_flags |= XFS_DIFLAG_REALTIME;
+ if (xflags & XFS_XFLAG_EXTSIZE)
+ di_flags |= XFS_DIFLAG_EXTSIZE;
+ }
+
+ ip->i_d.di_flags = di_flags;
+}
+
+STATIC void
+xfs_diflags_to_linux(
+ struct xfs_inode *ip)
+{
+ struct inode *inode = XFS_ITOV(ip);
+ unsigned int xflags = xfs_ip2xflags(ip);
+
+ if (xflags & XFS_XFLAG_IMMUTABLE)
+ inode->i_flags |= S_IMMUTABLE;
+ else
+ inode->i_flags &= ~S_IMMUTABLE;
+ if (xflags & XFS_XFLAG_APPEND)
+ inode->i_flags |= S_APPEND;
+ else
+ inode->i_flags &= ~S_APPEND;
+ if (xflags & XFS_XFLAG_SYNC)
+ inode->i_flags |= S_SYNC;
+ else
+ inode->i_flags &= ~S_SYNC;
+ if (xflags & XFS_XFLAG_NOATIME)
+ inode->i_flags |= S_NOATIME;
+ else
+ inode->i_flags &= ~S_NOATIME;
+}
+
+#define FSX_PROJID 1
+#define FSX_EXTSIZE 2
+#define FSX_XFLAGS 4
+#define FSX_NONBLOCK 8
+
+STATIC int
+xfs_ioctl_setattr(
+ xfs_inode_t *ip,
+ struct fsxattr *fa,
+ int mask)
+{
+ struct xfs_mount *mp = ip->i_mount;
+ struct xfs_trans *tp;
+ unsigned int lock_flags = 0;
+ struct xfs_dquot *udqp = NULL, *gdqp = NULL;
+ struct xfs_dquot *olddquot = NULL;
+ int code;
+
+ xfs_itrace_entry(ip);
+
+ if (mp->m_flags & XFS_MOUNT_RDONLY)
+ return XFS_ERROR(EROFS);
+ if (XFS_FORCED_SHUTDOWN(mp))
+ return XFS_ERROR(EIO);
+
+ /*
+ * If disk quotas is on, we make sure that the dquots do exist on disk,
+ * before we start any other transactions. Trying to do this later
+ * is messy. We don't care to take a readlock to look at the ids
+ * in inode here, because we can't hold it across the trans_reserve.
+ * If the IDs do change before we take the ilock, we're covered
+ * because the i_*dquot fields will get updated anyway.
+ */
+ if (XFS_IS_QUOTA_ON(mp) && (mask & FSX_PROJID)) {
+ code = XFS_QM_DQVOPALLOC(mp, ip, ip->i_d.di_uid,
+ ip->i_d.di_gid, fa->fsx_projid,
+ XFS_QMOPT_PQUOTA, &udqp, &gdqp);
+ if (code)
+ return code;
+ }
+
+ /*
+ * For the other attributes, we acquire the inode lock and
+ * first do an error checking pass.
+ */
+ tp = xfs_trans_alloc(mp, XFS_TRANS_SETATTR_NOT_SIZE);
+ code = xfs_trans_reserve(tp, 0, XFS_ICHANGE_LOG_RES(mp), 0, 0, 0);
+ if (code)
+ goto error_return;
+
+ lock_flags = XFS_ILOCK_EXCL;
+ xfs_ilock(ip, lock_flags);
+
+ /*
+ * CAP_FOWNER overrides the following restrictions:
+ *
+ * The user ID of the calling process must be equal
+ * to the file owner ID, except in cases where the
+ * CAP_FSETID capability is applicable.
+ */
+ if (current->fsuid != ip->i_d.di_uid && !capable(CAP_FOWNER)) {
+ code = XFS_ERROR(EPERM);
+ goto error_return;
+ }
+
+ /*
+ * Do a quota reservation only if projid is actually going to change.
+ */
+ if (mask & FSX_PROJID) {
+ if (XFS_IS_PQUOTA_ON(mp) &&
+ ip->i_d.di_projid != fa->fsx_projid) {
+ ASSERT(tp);
+ code = XFS_QM_DQVOPCHOWNRESV(mp, tp, ip, udqp, gdqp,
+ capable(CAP_FOWNER) ?
+ XFS_QMOPT_FORCE_RES : 0);
+ if (code) /* out of quota */
+ goto error_return;
+ }
+ }
+
+ if (mask & FSX_EXTSIZE) {
+ /*
+ * Can't change extent size if any extents are allocated.
+ */
+ if (ip->i_d.di_nextents &&
+ ((ip->i_d.di_extsize << mp->m_sb.sb_blocklog) !=
+ fa->fsx_extsize)) {
+ code = XFS_ERROR(EINVAL); /* EFBIG? */
+ goto error_return;
+ }
+
+ /*
+ * Extent size must be a multiple of the appropriate block
+ * size, if set at all.
+ */
+ if (fa->fsx_extsize != 0) {
+ xfs_extlen_t size;
+
+ if (XFS_IS_REALTIME_INODE(ip) ||
+ ((mask & FSX_XFLAGS) &&
+ (fa->fsx_xflags & XFS_XFLAG_REALTIME))) {
+ size = mp->m_sb.sb_rextsize <<
+ mp->m_sb.sb_blocklog;
+ } else {
+ size = mp->m_sb.sb_blocksize;
+ }
+
+ if (fa->fsx_extsize % size) {
+ code = XFS_ERROR(EINVAL);
+ goto error_return;
+ }
+ }
+ }
+
+
+ if (mask & FSX_XFLAGS) {
+ /*
+ * Can't change realtime flag if any extents are allocated.
+ */
+ if ((ip->i_d.di_nextents || ip->i_delayed_blks) &&
+ (XFS_IS_REALTIME_INODE(ip)) !=
+ (fa->fsx_xflags & XFS_XFLAG_REALTIME)) {
+ code = XFS_ERROR(EINVAL); /* EFBIG? */
+ goto error_return;
+ }
+
+ /*
+ * If realtime flag is set then must have realtime data.
+ */
+ if ((fa->fsx_xflags & XFS_XFLAG_REALTIME)) {
+ if ((mp->m_sb.sb_rblocks == 0) ||
+ (mp->m_sb.sb_rextsize == 0) ||
+ (ip->i_d.di_extsize % mp->m_sb.sb_rextsize)) {
+ code = XFS_ERROR(EINVAL);
+ goto error_return;
+ }
+ }
+
+ /*
+ * Can't modify an immutable/append-only file unless
+ * we have appropriate permission.
+ */
+ if ((ip->i_d.di_flags &
+ (XFS_DIFLAG_IMMUTABLE|XFS_DIFLAG_APPEND) ||
+ (fa->fsx_xflags &
+ (XFS_XFLAG_IMMUTABLE | XFS_XFLAG_APPEND))) &&
+ !capable(CAP_LINUX_IMMUTABLE)) {
+ code = XFS_ERROR(EPERM);
+ goto error_return;
+ }
+ }
+
+ xfs_trans_ijoin(tp, ip, lock_flags);
+ xfs_trans_ihold(tp, ip);
+
+ /*
+ * Change file ownership. Must be the owner or privileged.
+ * If the system was configured with the "restricted_chown"
+ * option, the owner is not permitted to give away the file,
+ * and can change the group id only to a group of which he
+ * or she is a member.
+ */
+ if (mask & FSX_PROJID) {
+ /*
+ * CAP_FSETID overrides the following restrictions:
+ *
+ * The set-user-ID and set-group-ID bits of a file will be
+ * cleared upon successful return from chown()
+ */
+ if ((ip->i_d.di_mode & (S_ISUID|S_ISGID)) &&
+ !capable(CAP_FSETID))
+ ip->i_d.di_mode &= ~(S_ISUID|S_ISGID);
+
+ /*
+ * Change the ownerships and register quota modifications
+ * in the transaction.
+ */
+ if (ip->i_d.di_projid != fa->fsx_projid) {
+ if (XFS_IS_PQUOTA_ON(mp)) {
+ olddquot = XFS_QM_DQVOPCHOWN(mp, tp, ip,
+ &ip->i_gdquot, gdqp);
+ }
+ ip->i_d.di_projid = fa->fsx_projid;
+
+ /*
+ * We may have to rev the inode as well as
+ * the superblock version number since projids didn't
+ * exist before DINODE_VERSION_2 and SB_VERSION_NLINK.
+ */
+ if (ip->i_d.di_version == XFS_DINODE_VERSION_1)
+ xfs_bump_ino_vers2(tp, ip);
+ }
+
+ }
+
+ if (mask & FSX_EXTSIZE)
+ ip->i_d.di_extsize = fa->fsx_extsize >> mp->m_sb.sb_blocklog;
+ if (mask & FSX_XFLAGS) {
+ xfs_set_diflags(ip, fa->fsx_xflags);
+ xfs_diflags_to_linux(ip);
+ }
+
+ xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
+ xfs_ichgtime(ip, XFS_ICHGTIME_CHG);
+
+ XFS_STATS_INC(xs_ig_attrchg);
+
+ /*
+ * If this is a synchronous mount, make sure that the
+ * transaction goes to disk before returning to the user.
+ * This is slightly sub-optimal in that truncates require
+ * two sync transactions instead of one for wsync filesystems.
+ * One for the truncate and one for the timestamps since we
+ * don't want to change the timestamps unless we're sure the
+ * truncate worked. Truncates are less than 1% of the laddis
+ * mix so this probably isn't worth the trouble to optimize.
+ */
+ if (mp->m_flags & XFS_MOUNT_WSYNC)
+ xfs_trans_set_sync(tp);
+ code = xfs_trans_commit(tp, 0);
+ xfs_iunlock(ip, lock_flags);
+
+ /*
+ * Release any dquot(s) the inode had kept before chown.
+ */
+ XFS_QM_DQRELE(mp, olddquot);
+ XFS_QM_DQRELE(mp, udqp);
+ XFS_QM_DQRELE(mp, gdqp);
+
+ if (code)
+ return code;
+
+ if (DM_EVENT_ENABLED(ip, DM_EVENT_ATTRIBUTE)) {
+ XFS_SEND_NAMESP(mp, DM_EVENT_ATTRIBUTE, ip, DM_RIGHT_NULL,
+ NULL, DM_RIGHT_NULL, NULL, NULL, 0, 0,
+ (mask & FSX_NONBLOCK) ? DM_FLAGS_NDELAY : 0);
+ }
+
+ return 0;
+
+ error_return:
+ XFS_QM_DQRELE(mp, udqp);
+ XFS_QM_DQRELE(mp, gdqp);
+ xfs_trans_cancel(tp, 0);
+ if (lock_flags)
+ xfs_iunlock(ip, lock_flags);
+ return code;
+}
+
STATIC int
xfs_ioc_fssetxattr(
xfs_inode_t *ip,
void __user *arg)
{
struct fsxattr fa;
- struct bhv_vattr *vattr;
- int error;
- int attr_flags;
+ unsigned int mask;
if (copy_from_user(&fa, arg, sizeof(fa)))
return -EFAULT;
- vattr = kmalloc(sizeof(*vattr), GFP_KERNEL);
- if (unlikely(!vattr))
- return -ENOMEM;
-
- attr_flags = 0;
+ mask = FSX_XFLAGS | FSX_EXTSIZE | FSX_PROJID;
if (filp->f_flags & (O_NDELAY|O_NONBLOCK))
- attr_flags |= ATTR_NONBLOCK;
-
- vattr->va_mask = XFS_AT_XFLAGS | XFS_AT_EXTSIZE | XFS_AT_PROJID;
- vattr->va_xflags = fa.fsx_xflags;
- vattr->va_extsize = fa.fsx_extsize;
- vattr->va_projid = fa.fsx_projid;
+ mask |= FSX_NONBLOCK;
- error = -xfs_setattr(ip, vattr, attr_flags, NULL);
- if (!error)
- vn_revalidate(XFS_ITOV(ip)); /* update flags */
- kfree(vattr);
- return 0;
+ return -xfs_ioctl_setattr(ip, &fa, mask);
}
STATIC int
struct file *filp,
void __user *arg)
{
- struct bhv_vattr *vattr;
+ struct fsxattr fa;
unsigned int flags;
- int attr_flags;
- int error;
+ unsigned int mask;
if (copy_from_user(&flags, arg, sizeof(flags)))
return -EFAULT;
FS_SYNC_FL))
return -EOPNOTSUPP;
- vattr = kmalloc(sizeof(*vattr), GFP_KERNEL);
- if (unlikely(!vattr))
- return -ENOMEM;
-
- attr_flags = 0;
+ mask = FSX_XFLAGS;
if (filp->f_flags & (O_NDELAY|O_NONBLOCK))
- attr_flags |= ATTR_NONBLOCK;
-
- vattr->va_mask = XFS_AT_XFLAGS;
- vattr->va_xflags = xfs_merge_ioc_xflags(flags, xfs_ip2xflags(ip));
+ mask |= FSX_NONBLOCK;
+ fa.fsx_xflags = xfs_merge_ioc_xflags(flags, xfs_ip2xflags(ip));
- error = -xfs_setattr(ip, vattr, attr_flags, NULL);
- if (likely(!error))
- vn_revalidate(XFS_ITOV(ip)); /* update flags */
- kfree(vattr);
- return error;
+ return -xfs_ioctl_setattr(ip, &fa, mask);
}
STATIC int
mark_inode_dirty_sync(inode);
}
-
-/*
- * Pull the link count and size up from the xfs inode to the linux inode
- */
-STATIC void
-xfs_validate_fields(
- struct inode *inode)
-{
- struct xfs_inode *ip = XFS_I(inode);
- loff_t size;
-
- /* we're under i_sem so i_size can't change under us */
- size = XFS_ISIZE(ip);
- if (i_size_read(inode) != size)
- i_size_write(inode, size);
-}
-
/*
* Hook in SELinux. This is not quite correct yet, what we really need
* here (as we do for default ACLs) is a mechanism by which creation of
xfs_cleanup_inode(
struct inode *dir,
struct inode *inode,
- struct dentry *dentry,
- int mode)
+ struct dentry *dentry)
{
struct xfs_name teardown;
*/
xfs_dentry_to_name(&teardown, dentry);
- if (S_ISDIR(mode))
- xfs_rmdir(XFS_I(dir), &teardown, XFS_I(inode));
- else
- xfs_remove(XFS_I(dir), &teardown, XFS_I(inode));
+ xfs_remove(XFS_I(dir), &teardown, XFS_I(inode));
iput(inode);
}
struct xfs_inode *ip = NULL;
xfs_acl_t *default_acl = NULL;
struct xfs_name name;
- attrexists_t test_default_acl = _ACL_DEFAULT_EXISTS;
+ int (*test_default_acl)(struct inode *) = _ACL_DEFAULT_EXISTS;
int error;
/*
}
- if (S_ISDIR(mode))
- xfs_validate_fields(inode);
d_instantiate(dentry, inode);
- xfs_validate_fields(dir);
return -error;
out_cleanup_inode:
- xfs_cleanup_inode(dir, inode, dentry, mode);
+ xfs_cleanup_inode(dir, inode, dentry);
out_free_acl:
if (default_acl)
_ACL_FREE(default_acl);
return ERR_PTR(-ENAMETOOLONG);
xfs_dentry_to_name(&name, dentry);
- error = xfs_lookup(XFS_I(dir), &name, &cip);
+ error = xfs_lookup(XFS_I(dir), &name, &cip, NULL);
if (unlikely(error)) {
if (unlikely(error != ENOENT))
return ERR_PTR(-error);
return d_splice_alias(cip->i_vnode, dentry);
}
+STATIC struct dentry *
+xfs_vn_ci_lookup(
+ struct inode *dir,
+ struct dentry *dentry,
+ struct nameidata *nd)
+{
+ struct xfs_inode *ip;
+ struct xfs_name xname;
+ struct xfs_name ci_name;
+ struct qstr dname;
+ int error;
+
+ if (dentry->d_name.len >= MAXNAMELEN)
+ return ERR_PTR(-ENAMETOOLONG);
+
+ xfs_dentry_to_name(&xname, dentry);
+ error = xfs_lookup(XFS_I(dir), &xname, &ip, &ci_name);
+ if (unlikely(error)) {
+ if (unlikely(error != ENOENT))
+ return ERR_PTR(-error);
+ /*
+ * call d_add(dentry, NULL) here when d_drop_negative_children
+ * is called in xfs_vn_mknod (ie. allow negative dentries
+ * with CI filesystems).
+ */
+ return NULL;
+ }
+
+ /* if exact match, just splice and exit */
+ if (!ci_name.name)
+ return d_splice_alias(ip->i_vnode, dentry);
+
+ /* else case-insensitive match... */
+ dname.name = ci_name.name;
+ dname.len = ci_name.len;
+ dentry = d_add_ci(ip->i_vnode, dentry, &dname);
+ kmem_free(ci_name.name);
+ return dentry;
+}
+
STATIC int
xfs_vn_link(
struct dentry *old_dentry,
}
xfs_iflags_set(XFS_I(dir), XFS_IMODIFIED);
- xfs_validate_fields(inode);
d_instantiate(dentry, inode);
return 0;
}
struct inode *dir,
struct dentry *dentry)
{
- struct inode *inode;
struct xfs_name name;
int error;
- inode = dentry->d_inode;
xfs_dentry_to_name(&name, dentry);
- error = xfs_remove(XFS_I(dir), &name, XFS_I(inode));
- if (likely(!error)) {
- xfs_validate_fields(dir); /* size needs update */
- xfs_validate_fields(inode);
- }
- return -error;
+ error = -xfs_remove(XFS_I(dir), &name, XFS_I(dentry->d_inode));
+ if (error)
+ return error;
+
+ /*
+ * With unlink, the VFS makes the dentry "negative": no inode,
+ * but still hashed. This is incompatible with case-insensitive
+ * mode, so invalidate (unhash) the dentry in CI-mode.
+ */
+ if (xfs_sb_version_hasasciici(&XFS_M(dir->i_sb)->m_sb))
+ d_invalidate(dentry);
+ return 0;
}
STATIC int
goto out_cleanup_inode;
d_instantiate(dentry, inode);
- xfs_validate_fields(dir);
- xfs_validate_fields(inode);
return 0;
out_cleanup_inode:
- xfs_cleanup_inode(dir, inode, dentry, 0);
+ xfs_cleanup_inode(dir, inode, dentry);
out:
return -error;
}
-STATIC int
-xfs_vn_rmdir(
- struct inode *dir,
- struct dentry *dentry)
-{
- struct inode *inode = dentry->d_inode;
- struct xfs_name name;
- int error;
-
- xfs_dentry_to_name(&name, dentry);
-
- error = xfs_rmdir(XFS_I(dir), &name, XFS_I(inode));
- if (likely(!error)) {
- xfs_validate_fields(inode);
- xfs_validate_fields(dir);
- }
- return -error;
-}
-
STATIC int
xfs_vn_rename(
struct inode *odir,
struct inode *new_inode = ndentry->d_inode;
struct xfs_name oname;
struct xfs_name nname;
- int error;
xfs_dentry_to_name(&oname, odentry);
xfs_dentry_to_name(&nname, ndentry);
- error = xfs_rename(XFS_I(odir), &oname, XFS_I(odentry->d_inode),
+ return -xfs_rename(XFS_I(odir), &oname, XFS_I(odentry->d_inode),
XFS_I(ndir), &nname, new_inode ?
XFS_I(new_inode) : NULL);
- if (likely(!error)) {
- if (new_inode)
- xfs_validate_fields(new_inode);
- xfs_validate_fields(odir);
- if (ndir != odir)
- xfs_validate_fields(ndir);
- }
- return -error;
}
/*
STATIC int
xfs_vn_setattr(
struct dentry *dentry,
- struct iattr *attr)
+ struct iattr *iattr)
{
- struct inode *inode = dentry->d_inode;
- unsigned int ia_valid = attr->ia_valid;
- bhv_vattr_t vattr = { 0 };
- int flags = 0;
- int error;
-
- if (ia_valid & ATTR_UID) {
- vattr.va_mask |= XFS_AT_UID;
- vattr.va_uid = attr->ia_uid;
- }
- if (ia_valid & ATTR_GID) {
- vattr.va_mask |= XFS_AT_GID;
- vattr.va_gid = attr->ia_gid;
- }
- if (ia_valid & ATTR_SIZE) {
- vattr.va_mask |= XFS_AT_SIZE;
- vattr.va_size = attr->ia_size;
- }
- if (ia_valid & ATTR_ATIME) {
- vattr.va_mask |= XFS_AT_ATIME;
- vattr.va_atime = attr->ia_atime;
- inode->i_atime = attr->ia_atime;
- }
- if (ia_valid & ATTR_MTIME) {
- vattr.va_mask |= XFS_AT_MTIME;
- vattr.va_mtime = attr->ia_mtime;
- }
- if (ia_valid & ATTR_CTIME) {
- vattr.va_mask |= XFS_AT_CTIME;
- vattr.va_ctime = attr->ia_ctime;
- }
- if (ia_valid & ATTR_MODE) {
- vattr.va_mask |= XFS_AT_MODE;
- vattr.va_mode = attr->ia_mode;
- if (!in_group_p(inode->i_gid) && !capable(CAP_FSETID))
- inode->i_mode &= ~S_ISGID;
- }
-
- if (ia_valid & (ATTR_MTIME_SET | ATTR_ATIME_SET))
- flags |= ATTR_UTIME;
-#ifdef ATTR_NO_BLOCK
- if ((ia_valid & ATTR_NO_BLOCK))
- flags |= ATTR_NONBLOCK;
-#endif
-
- error = xfs_setattr(XFS_I(inode), &vattr, flags, NULL);
- if (likely(!error))
- vn_revalidate(vn_from_inode(inode));
- return -error;
+ return -xfs_setattr(XFS_I(dentry->d_inode), iattr, 0, NULL);
}
/*
WARN_ON(error);
}
-STATIC int
-xfs_vn_setxattr(
- struct dentry *dentry,
- const char *name,
- const void *data,
- size_t size,
- int flags)
-{
- bhv_vnode_t *vp = vn_from_inode(dentry->d_inode);
- char *attr = (char *)name;
- attrnames_t *namesp;
- int xflags = 0;
- int error;
-
- namesp = attr_lookup_namespace(attr, attr_namespaces, ATTR_NAMECOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- attr += namesp->attr_namelen;
- error = namesp->attr_capable(vp, NULL);
- if (error)
- return error;
-
- /* Convert Linux syscall to XFS internal ATTR flags */
- if (flags & XATTR_CREATE)
- xflags |= ATTR_CREATE;
- if (flags & XATTR_REPLACE)
- xflags |= ATTR_REPLACE;
- xflags |= namesp->attr_flag;
- return namesp->attr_set(vp, attr, (void *)data, size, xflags);
-}
-
-STATIC ssize_t
-xfs_vn_getxattr(
- struct dentry *dentry,
- const char *name,
- void *data,
- size_t size)
-{
- bhv_vnode_t *vp = vn_from_inode(dentry->d_inode);
- char *attr = (char *)name;
- attrnames_t *namesp;
- int xflags = 0;
- ssize_t error;
-
- namesp = attr_lookup_namespace(attr, attr_namespaces, ATTR_NAMECOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- attr += namesp->attr_namelen;
- error = namesp->attr_capable(vp, NULL);
- if (error)
- return error;
-
- /* Convert Linux syscall to XFS internal ATTR flags */
- if (!size) {
- xflags |= ATTR_KERNOVAL;
- data = NULL;
- }
- xflags |= namesp->attr_flag;
- return namesp->attr_get(vp, attr, (void *)data, size, xflags);
-}
-
-STATIC ssize_t
-xfs_vn_listxattr(
- struct dentry *dentry,
- char *data,
- size_t size)
-{
- bhv_vnode_t *vp = vn_from_inode(dentry->d_inode);
- int error, xflags = ATTR_KERNAMELS;
- ssize_t result;
-
- if (!size)
- xflags |= ATTR_KERNOVAL;
- xflags |= capable(CAP_SYS_ADMIN) ? ATTR_KERNFULLS : ATTR_KERNORMALS;
-
- error = attr_generic_list(vp, data, size, xflags, &result);
- if (error < 0)
- return error;
- return result;
-}
-
-STATIC int
-xfs_vn_removexattr(
- struct dentry *dentry,
- const char *name)
-{
- bhv_vnode_t *vp = vn_from_inode(dentry->d_inode);
- char *attr = (char *)name;
- attrnames_t *namesp;
- int xflags = 0;
- int error;
-
- namesp = attr_lookup_namespace(attr, attr_namespaces, ATTR_NAMECOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- attr += namesp->attr_namelen;
- error = namesp->attr_capable(vp, NULL);
- if (error)
- return error;
- xflags |= namesp->attr_flag;
- return namesp->attr_remove(vp, attr, xflags);
-}
-
STATIC long
xfs_vn_fallocate(
struct inode *inode,
xfs_ilock(ip, XFS_IOLOCK_EXCL);
error = xfs_change_file_space(ip, XFS_IOC_RESVSP, &bf,
- 0, NULL, ATTR_NOLOCK);
+ 0, NULL, XFS_ATTR_NOLOCK);
if (!error && !(mode & FALLOC_FL_KEEP_SIZE) &&
offset + len > i_size_read(inode))
new_size = offset + len;
/* Change file size if needed */
if (new_size) {
- bhv_vattr_t va;
+ struct iattr iattr;
- va.va_mask = XFS_AT_SIZE;
- va.va_size = new_size;
- error = xfs_setattr(ip, &va, ATTR_NOLOCK, NULL);
+ iattr.ia_valid = ATTR_SIZE;
+ iattr.ia_size = new_size;
+ error = xfs_setattr(ip, &iattr, XFS_ATTR_NOLOCK, NULL);
}
xfs_iunlock(ip, XFS_IOLOCK_EXCL);
.truncate = xfs_vn_truncate,
.getattr = xfs_vn_getattr,
.setattr = xfs_vn_setattr,
- .setxattr = xfs_vn_setxattr,
- .getxattr = xfs_vn_getxattr,
+ .setxattr = generic_setxattr,
+ .getxattr = generic_getxattr,
+ .removexattr = generic_removexattr,
.listxattr = xfs_vn_listxattr,
- .removexattr = xfs_vn_removexattr,
.fallocate = xfs_vn_fallocate,
};
.unlink = xfs_vn_unlink,
.symlink = xfs_vn_symlink,
.mkdir = xfs_vn_mkdir,
- .rmdir = xfs_vn_rmdir,
+ /*
+ * Yes, XFS uses the same method for rmdir and unlink.
+ *
+ * There are some subtile differences deeper in the code,
+ * but we use S_ISDIR to check for those.
+ */
+ .rmdir = xfs_vn_unlink,
+ .mknod = xfs_vn_mknod,
+ .rename = xfs_vn_rename,
+ .permission = xfs_vn_permission,
+ .getattr = xfs_vn_getattr,
+ .setattr = xfs_vn_setattr,
+ .setxattr = generic_setxattr,
+ .getxattr = generic_getxattr,
+ .removexattr = generic_removexattr,
+ .listxattr = xfs_vn_listxattr,
+};
+
+const struct inode_operations xfs_dir_ci_inode_operations = {
+ .create = xfs_vn_create,
+ .lookup = xfs_vn_ci_lookup,
+ .link = xfs_vn_link,
+ .unlink = xfs_vn_unlink,
+ .symlink = xfs_vn_symlink,
+ .mkdir = xfs_vn_mkdir,
+ /*
+ * Yes, XFS uses the same method for rmdir and unlink.
+ *
+ * There are some subtile differences deeper in the code,
+ * but we use S_ISDIR to check for those.
+ */
+ .rmdir = xfs_vn_unlink,
.mknod = xfs_vn_mknod,
.rename = xfs_vn_rename,
.permission = xfs_vn_permission,
.getattr = xfs_vn_getattr,
.setattr = xfs_vn_setattr,
- .setxattr = xfs_vn_setxattr,
- .getxattr = xfs_vn_getxattr,
+ .setxattr = generic_setxattr,
+ .getxattr = generic_getxattr,
+ .removexattr = generic_removexattr,
.listxattr = xfs_vn_listxattr,
- .removexattr = xfs_vn_removexattr,
};
const struct inode_operations xfs_symlink_inode_operations = {
.permission = xfs_vn_permission,
.getattr = xfs_vn_getattr,
.setattr = xfs_vn_setattr,
- .setxattr = xfs_vn_setxattr,
- .getxattr = xfs_vn_getxattr,
+ .setxattr = generic_setxattr,
+ .getxattr = generic_getxattr,
+ .removexattr = generic_removexattr,
.listxattr = xfs_vn_listxattr,
- .removexattr = xfs_vn_removexattr,
};
extern const struct inode_operations xfs_inode_operations;
extern const struct inode_operations xfs_dir_inode_operations;
+extern const struct inode_operations xfs_dir_ci_inode_operations;
extern const struct inode_operations xfs_symlink_inode_operations;
extern const struct file_operations xfs_file_operations;
extern const struct file_operations xfs_dir_file_operations;
extern const struct file_operations xfs_invis_file_operations;
+extern ssize_t xfs_vn_listxattr(struct dentry *, char *data, size_t size);
struct xfs_inode;
extern void xfs_ichgtime(struct xfs_inode *, int);
#include <linux/log2.h>
#include <linux/spinlock.h>
#include <linux/random.h>
+#include <linux/ctype.h>
#include <asm/page.h>
#include <asm/div64.h>
return x;
}
+/* ARM old ABI has some weird alignment/padding */
+#if defined(__arm__) && !defined(__ARM_EABI__)
+#define __arch_pack __attribute__((packed))
+#else
+#define __arch_pack
+#endif
+
#endif /* __XFS_LINUX__ */
return len;
}
-void
+int
xfs_init_procfs(void)
{
if (!proc_mkdir("fs/xfs", NULL))
- return;
- create_proc_read_entry("fs/xfs/stat", 0, NULL, xfs_read_xfsstats, NULL);
+ goto out;
+
+ if (!create_proc_read_entry("fs/xfs/stat", 0, NULL,
+ xfs_read_xfsstats, NULL))
+ goto out_remove_entry;
+ return 0;
+
+ out_remove_entry:
+ remove_proc_entry("fs/xfs", NULL);
+ out:
+ return -ENOMEM;
}
void
#define XFS_STATS_DEC(v) (per_cpu(xfsstats, current_cpu()).v--)
#define XFS_STATS_ADD(v, inc) (per_cpu(xfsstats, current_cpu()).v += (inc))
-extern void xfs_init_procfs(void);
+extern int xfs_init_procfs(void);
extern void xfs_cleanup_procfs(void);
# define XFS_STATS_DEC(count)
# define XFS_STATS_ADD(count, inc)
-static inline void xfs_init_procfs(void) { };
-static inline void xfs_cleanup_procfs(void) { };
+static inline int xfs_init_procfs(void)
+{
+ return 0;
+}
+
+static inline void xfs_cleanup_procfs(void)
+{
+}
#endif /* !CONFIG_PROC_FS */
#include "xfs_version.h"
#include "xfs_log_priv.h"
#include "xfs_trans_priv.h"
+#include "xfs_filestream.h"
+#include "xfs_da_btree.h"
+#include "xfs_dir2_trace.h"
+#include "xfs_extfree_item.h"
+#include "xfs_mru_cache.h"
+#include "xfs_inode_item.h"
#include <linux/namei.h>
#include <linux/init.h>
#include <linux/writeback.h>
#include <linux/kthread.h>
#include <linux/freezer.h>
+#include <linux/parser.h>
static struct quotactl_ops xfs_quotactl_operations;
static struct super_operations xfs_super_operations;
{
struct xfs_mount_args *args;
- args = kmem_zalloc(sizeof(struct xfs_mount_args), KM_SLEEP);
+ args = kzalloc(sizeof(struct xfs_mount_args), GFP_KERNEL);
+ if (!args)
+ return NULL;
+
args->logbufs = args->logbufsize = -1;
strncpy(args->fsname, sb->s_id, MAXNAMELEN);
#define MNTOPT_XDSM "xdsm" /* DMI enabled (DMAPI / XDSM) */
#define MNTOPT_DMI "dmi" /* DMI enabled (DMAPI / XDSM) */
+/*
+ * Table driven mount option parser.
+ *
+ * Currently only used for remount, but it will be used for mount
+ * in the future, too.
+ */
+enum {
+ Opt_barrier, Opt_nobarrier, Opt_err
+};
+
+static match_table_t tokens = {
+ {Opt_barrier, "barrier"},
+ {Opt_nobarrier, "nobarrier"},
+ {Opt_err, NULL}
+};
+
+
STATIC unsigned long
suffix_strtoul(char *s, char **endp, unsigned int base)
{
args->flags |= XFSMNT_ATTR2;
} else if (!strcmp(this_char, MNTOPT_NOATTR2)) {
args->flags &= ~XFSMNT_ATTR2;
+ args->flags |= XFSMNT_NOATTR2;
} else if (!strcmp(this_char, MNTOPT_FILESTREAM)) {
args->flags2 |= XFSMNT2_FILESTREAMS;
} else if (!strcmp(this_char, MNTOPT_NOQUOTA)) {
inode->i_mapping->a_ops = &xfs_address_space_operations;
break;
case S_IFDIR:
- inode->i_op = &xfs_dir_inode_operations;
+ if (xfs_sb_version_hasasciici(&XFS_M(inode->i_sb)->m_sb))
+ inode->i_op = &xfs_dir_ci_inode_operations;
+ else
+ inode->i_op = &xfs_dir_inode_operations;
inode->i_fop = &xfs_dir_file_operations;
break;
case S_IFLNK:
return;
}
- if (mp->m_ddev_targp->bt_bdev->bd_disk->queue->ordered ==
- QUEUE_ORDERED_NONE) {
- xfs_fs_cmn_err(CE_NOTE, mp,
- "Disabling barriers, not supported by the underlying device");
- mp->m_flags &= ~XFS_MOUNT_BARRIER;
- return;
- }
-
if (xfs_readonly_buftarg(mp->m_ddev_targp)) {
xfs_fs_cmn_err(CE_NOTE, mp,
"Disabling barriers, underlying device is readonly");
blkdev_issue_flush(buftarg->bt_bdev, NULL);
}
+STATIC void
+xfs_close_devices(
+ struct xfs_mount *mp)
+{
+ if (mp->m_logdev_targp && mp->m_logdev_targp != mp->m_ddev_targp) {
+ struct block_device *logdev = mp->m_logdev_targp->bt_bdev;
+ xfs_free_buftarg(mp->m_logdev_targp);
+ xfs_blkdev_put(logdev);
+ }
+ if (mp->m_rtdev_targp) {
+ struct block_device *rtdev = mp->m_rtdev_targp->bt_bdev;
+ xfs_free_buftarg(mp->m_rtdev_targp);
+ xfs_blkdev_put(rtdev);
+ }
+ xfs_free_buftarg(mp->m_ddev_targp);
+}
+
+/*
+ * The file system configurations are:
+ * (1) device (partition) with data and internal log
+ * (2) logical volume with data and log subvolumes.
+ * (3) logical volume with data, log, and realtime subvolumes.
+ *
+ * We only have to handle opening the log and realtime volumes here if
+ * they are present. The data subvolume has already been opened by
+ * get_sb_bdev() and is stored in sb->s_bdev.
+ */
+STATIC int
+xfs_open_devices(
+ struct xfs_mount *mp,
+ struct xfs_mount_args *args)
+{
+ struct block_device *ddev = mp->m_super->s_bdev;
+ struct block_device *logdev = NULL, *rtdev = NULL;
+ int error;
+
+ /*
+ * Open real time and log devices - order is important.
+ */
+ if (args->logname[0]) {
+ error = xfs_blkdev_get(mp, args->logname, &logdev);
+ if (error)
+ goto out;
+ }
+
+ if (args->rtname[0]) {
+ error = xfs_blkdev_get(mp, args->rtname, &rtdev);
+ if (error)
+ goto out_close_logdev;
+
+ if (rtdev == ddev || rtdev == logdev) {
+ cmn_err(CE_WARN,
+ "XFS: Cannot mount filesystem with identical rtdev and ddev/logdev.");
+ error = EINVAL;
+ goto out_close_rtdev;
+ }
+ }
+
+ /*
+ * Setup xfs_mount buffer target pointers
+ */
+ error = ENOMEM;
+ mp->m_ddev_targp = xfs_alloc_buftarg(ddev, 0);
+ if (!mp->m_ddev_targp)
+ goto out_close_rtdev;
+
+ if (rtdev) {
+ mp->m_rtdev_targp = xfs_alloc_buftarg(rtdev, 1);
+ if (!mp->m_rtdev_targp)
+ goto out_free_ddev_targ;
+ }
+
+ if (logdev && logdev != ddev) {
+ mp->m_logdev_targp = xfs_alloc_buftarg(logdev, 1);
+ if (!mp->m_logdev_targp)
+ goto out_free_rtdev_targ;
+ } else {
+ mp->m_logdev_targp = mp->m_ddev_targp;
+ }
+
+ return 0;
+
+ out_free_rtdev_targ:
+ if (mp->m_rtdev_targp)
+ xfs_free_buftarg(mp->m_rtdev_targp);
+ out_free_ddev_targ:
+ xfs_free_buftarg(mp->m_ddev_targp);
+ out_close_rtdev:
+ if (rtdev)
+ xfs_blkdev_put(rtdev);
+ out_close_logdev:
+ if (logdev && logdev != ddev)
+ xfs_blkdev_put(logdev);
+ out:
+ return error;
+}
+
+/*
+ * Setup xfs_mount buffer target pointers based on superblock
+ */
+STATIC int
+xfs_setup_devices(
+ struct xfs_mount *mp)
+{
+ int error;
+
+ error = xfs_setsize_buftarg(mp->m_ddev_targp, mp->m_sb.sb_blocksize,
+ mp->m_sb.sb_sectsize);
+ if (error)
+ return error;
+
+ if (mp->m_logdev_targp && mp->m_logdev_targp != mp->m_ddev_targp) {
+ unsigned int log_sector_size = BBSIZE;
+
+ if (xfs_sb_version_hassector(&mp->m_sb))
+ log_sector_size = mp->m_sb.sb_logsectsize;
+ error = xfs_setsize_buftarg(mp->m_logdev_targp,
+ mp->m_sb.sb_blocksize,
+ log_sector_size);
+ if (error)
+ return error;
+ }
+ if (mp->m_rtdev_targp) {
+ error = xfs_setsize_buftarg(mp->m_rtdev_targp,
+ mp->m_sb.sb_blocksize,
+ mp->m_sb.sb_sectsize);
+ if (error)
+ return error;
+ }
+
+ return 0;
+}
+
/*
* XFS AIL push thread support
*/
inode_init_once(vn_to_inode((bhv_vnode_t *)vnode));
}
-STATIC int __init
-xfs_init_zones(void)
-{
- xfs_vnode_zone = kmem_zone_init_flags(sizeof(bhv_vnode_t), "xfs_vnode",
- KM_ZONE_HWALIGN | KM_ZONE_RECLAIM |
- KM_ZONE_SPREAD,
- xfs_fs_inode_init_once);
- if (!xfs_vnode_zone)
- goto out;
-
- xfs_ioend_zone = kmem_zone_init(sizeof(xfs_ioend_t), "xfs_ioend");
- if (!xfs_ioend_zone)
- goto out_destroy_vnode_zone;
-
- xfs_ioend_pool = mempool_create_slab_pool(4 * MAX_BUF_PER_PAGE,
- xfs_ioend_zone);
- if (!xfs_ioend_pool)
- goto out_free_ioend_zone;
- return 0;
-
- out_free_ioend_zone:
- kmem_zone_destroy(xfs_ioend_zone);
- out_destroy_vnode_zone:
- kmem_zone_destroy(xfs_vnode_zone);
- out:
- return -ENOMEM;
-}
-
-STATIC void
-xfs_destroy_zones(void)
-{
- mempool_destroy(xfs_ioend_pool);
- kmem_zone_destroy(xfs_vnode_zone);
- kmem_zone_destroy(xfs_ioend_zone);
-}
-
/*
* Attempt to flush the inode, this will actually fail
* if the inode is pinned, but we dirty the inode again
list_del(&work->w_list);
if (work == &mp->m_sync_work)
continue;
- kmem_free(work, sizeof(struct bhv_vfs_sync_work));
+ kmem_free(work);
}
}
struct super_block *sb)
{
struct xfs_mount *mp = XFS_M(sb);
+ struct xfs_inode *rip = mp->m_rootip;
+ int unmount_event_flags = 0;
int error;
kthread_stop(mp->m_sync_task);
xfs_sync(mp, SYNC_ATTR | SYNC_DELWRI);
- error = xfs_unmount(mp, 0, NULL);
- if (error)
- printk("XFS: unmount got error=%d\n", error);
+
+#ifdef HAVE_DMAPI
+ if (mp->m_flags & XFS_MOUNT_DMAPI) {
+ unmount_event_flags =
+ (mp->m_dmevmask & (1 << DM_EVENT_UNMOUNT)) ?
+ 0 : DM_FLAGS_UNWANTED;
+ /*
+ * Ignore error from dmapi here, first unmount is not allowed
+ * to fail anyway, and second we wouldn't want to fail a
+ * unmount because of dmapi.
+ */
+ XFS_SEND_PREUNMOUNT(mp, rip, DM_RIGHT_NULL, rip, DM_RIGHT_NULL,
+ NULL, NULL, 0, 0, unmount_event_flags);
+ }
+#endif
+
+ /*
+ * Blow away any referenced inode in the filestreams cache.
+ * This can and will cause log traffic as inodes go inactive
+ * here.
+ */
+ xfs_filestream_unmount(mp);
+
+ XFS_bflush(mp->m_ddev_targp);
+ error = xfs_unmount_flush(mp, 0);
+ WARN_ON(error);
+
+ IRELE(rip);
+
+ /*
+ * If we're forcing a shutdown, typically because of a media error,
+ * we want to make sure we invalidate dirty pages that belong to
+ * referenced vnodes as well.
+ */
+ if (XFS_FORCED_SHUTDOWN(mp)) {
+ error = xfs_sync(mp, SYNC_WAIT | SYNC_CLOSE);
+ ASSERT(error != EFSCORRUPTED);
+ }
+
+ if (mp->m_flags & XFS_MOUNT_DMAPI) {
+ XFS_SEND_UNMOUNT(mp, rip, DM_RIGHT_NULL, 0, 0,
+ unmount_event_flags);
+ }
+
+ xfs_unmountfs(mp);
+ xfs_icsb_destroy_counters(mp);
+ xfs_close_devices(mp);
+ xfs_qmops_put(mp);
+ xfs_dmops_put(mp);
+ kfree(mp);
}
STATIC void
char *options)
{
struct xfs_mount *mp = XFS_M(sb);
- struct xfs_mount_args *args = xfs_args_allocate(sb, 0);
- int error;
+ substring_t args[MAX_OPT_ARGS];
+ char *p;
- error = xfs_parseargs(mp, options, args, 1);
- if (!error)
- error = xfs_mntupdate(mp, flags, args);
- kmem_free(args, sizeof(*args));
- return -error;
+ while ((p = strsep(&options, ",")) != NULL) {
+ int token;
+
+ if (!*p)
+ continue;
+
+ token = match_token(p, tokens, args);
+ switch (token) {
+ case Opt_barrier:
+ mp->m_flags |= XFS_MOUNT_BARRIER;
+
+ /*
+ * Test if barriers are actually working if we can,
+ * else delay this check until the filesystem is
+ * marked writeable.
+ */
+ if (!(mp->m_flags & XFS_MOUNT_RDONLY))
+ xfs_mountfs_check_barriers(mp);
+ break;
+ case Opt_nobarrier:
+ mp->m_flags &= ~XFS_MOUNT_BARRIER;
+ break;
+ default:
+ printk(KERN_INFO
+ "XFS: mount option \"%s\" not supported for remount\n", p);
+ return -EINVAL;
+ }
+ }
+
+ /* rw/ro -> rw */
+ if ((mp->m_flags & XFS_MOUNT_RDONLY) && !(*flags & MS_RDONLY)) {
+ mp->m_flags &= ~XFS_MOUNT_RDONLY;
+ if (mp->m_flags & XFS_MOUNT_BARRIER)
+ xfs_mountfs_check_barriers(mp);
+ }
+
+ /* rw -> ro */
+ if (!(mp->m_flags & XFS_MOUNT_RDONLY) && (*flags & MS_RDONLY)) {
+ xfs_filestream_flush(mp);
+ xfs_sync(mp, SYNC_DATA_QUIESCE);
+ xfs_attr_quiesce(mp);
+ mp->m_flags |= XFS_MOUNT_RDONLY;
+ }
+
+ return 0;
}
/*
Q_XSETPQLIM), id, (caddr_t)fdq);
}
+/*
+ * This function fills in xfs_mount_t fields based on mount args.
+ * Note: the superblock has _not_ yet been read in.
+ */
+STATIC int
+xfs_start_flags(
+ struct xfs_mount_args *ap,
+ struct xfs_mount *mp)
+{
+ /* Values are in BBs */
+ if ((ap->flags & XFSMNT_NOALIGN) != XFSMNT_NOALIGN) {
+ /*
+ * At this point the superblock has not been read
+ * in, therefore we do not know the block size.
+ * Before the mount call ends we will convert
+ * these to FSBs.
+ */
+ mp->m_dalign = ap->sunit;
+ mp->m_swidth = ap->swidth;
+ }
+
+ if (ap->logbufs != -1 &&
+ ap->logbufs != 0 &&
+ (ap->logbufs < XLOG_MIN_ICLOGS ||
+ ap->logbufs > XLOG_MAX_ICLOGS)) {
+ cmn_err(CE_WARN,
+ "XFS: invalid logbufs value: %d [not %d-%d]",
+ ap->logbufs, XLOG_MIN_ICLOGS, XLOG_MAX_ICLOGS);
+ return XFS_ERROR(EINVAL);
+ }
+ mp->m_logbufs = ap->logbufs;
+ if (ap->logbufsize != -1 &&
+ ap->logbufsize != 0 &&
+ (ap->logbufsize < XLOG_MIN_RECORD_BSIZE ||
+ ap->logbufsize > XLOG_MAX_RECORD_BSIZE ||
+ !is_power_of_2(ap->logbufsize))) {
+ cmn_err(CE_WARN,
+ "XFS: invalid logbufsize: %d [not 16k,32k,64k,128k or 256k]",
+ ap->logbufsize);
+ return XFS_ERROR(EINVAL);
+ }
+ mp->m_logbsize = ap->logbufsize;
+ mp->m_fsname_len = strlen(ap->fsname) + 1;
+ mp->m_fsname = kmem_alloc(mp->m_fsname_len, KM_SLEEP);
+ strcpy(mp->m_fsname, ap->fsname);
+ if (ap->rtname[0]) {
+ mp->m_rtname = kmem_alloc(strlen(ap->rtname) + 1, KM_SLEEP);
+ strcpy(mp->m_rtname, ap->rtname);
+ }
+ if (ap->logname[0]) {
+ mp->m_logname = kmem_alloc(strlen(ap->logname) + 1, KM_SLEEP);
+ strcpy(mp->m_logname, ap->logname);
+ }
+
+ if (ap->flags & XFSMNT_WSYNC)
+ mp->m_flags |= XFS_MOUNT_WSYNC;
+#if XFS_BIG_INUMS
+ if (ap->flags & XFSMNT_INO64) {
+ mp->m_flags |= XFS_MOUNT_INO64;
+ mp->m_inoadd = XFS_INO64_OFFSET;
+ }
+#endif
+ if (ap->flags & XFSMNT_RETERR)
+ mp->m_flags |= XFS_MOUNT_RETERR;
+ if (ap->flags & XFSMNT_NOALIGN)
+ mp->m_flags |= XFS_MOUNT_NOALIGN;
+ if (ap->flags & XFSMNT_SWALLOC)
+ mp->m_flags |= XFS_MOUNT_SWALLOC;
+ if (ap->flags & XFSMNT_OSYNCISOSYNC)
+ mp->m_flags |= XFS_MOUNT_OSYNCISOSYNC;
+ if (ap->flags & XFSMNT_32BITINODES)
+ mp->m_flags |= XFS_MOUNT_32BITINODES;
+
+ if (ap->flags & XFSMNT_IOSIZE) {
+ if (ap->iosizelog > XFS_MAX_IO_LOG ||
+ ap->iosizelog < XFS_MIN_IO_LOG) {
+ cmn_err(CE_WARN,
+ "XFS: invalid log iosize: %d [not %d-%d]",
+ ap->iosizelog, XFS_MIN_IO_LOG,
+ XFS_MAX_IO_LOG);
+ return XFS_ERROR(EINVAL);
+ }
+
+ mp->m_flags |= XFS_MOUNT_DFLT_IOSIZE;
+ mp->m_readio_log = mp->m_writeio_log = ap->iosizelog;
+ }
+
+ if (ap->flags & XFSMNT_IKEEP)
+ mp->m_flags |= XFS_MOUNT_IKEEP;
+ if (ap->flags & XFSMNT_DIRSYNC)
+ mp->m_flags |= XFS_MOUNT_DIRSYNC;
+ if (ap->flags & XFSMNT_ATTR2)
+ mp->m_flags |= XFS_MOUNT_ATTR2;
+ if (ap->flags & XFSMNT_NOATTR2)
+ mp->m_flags |= XFS_MOUNT_NOATTR2;
+
+ if (ap->flags2 & XFSMNT2_COMPAT_IOSIZE)
+ mp->m_flags |= XFS_MOUNT_COMPAT_IOSIZE;
+
+ /*
+ * no recovery flag requires a read-only mount
+ */
+ if (ap->flags & XFSMNT_NORECOVERY) {
+ if (!(mp->m_flags & XFS_MOUNT_RDONLY)) {
+ cmn_err(CE_WARN,
+ "XFS: tried to mount a FS read-write without recovery!");
+ return XFS_ERROR(EINVAL);
+ }
+ mp->m_flags |= XFS_MOUNT_NORECOVERY;
+ }
+
+ if (ap->flags & XFSMNT_NOUUID)
+ mp->m_flags |= XFS_MOUNT_NOUUID;
+ if (ap->flags & XFSMNT_BARRIER)
+ mp->m_flags |= XFS_MOUNT_BARRIER;
+ else
+ mp->m_flags &= ~XFS_MOUNT_BARRIER;
+
+ if (ap->flags2 & XFSMNT2_FILESTREAMS)
+ mp->m_flags |= XFS_MOUNT_FILESTREAMS;
+
+ if (ap->flags & XFSMNT_DMAPI)
+ mp->m_flags |= XFS_MOUNT_DMAPI;
+ return 0;
+}
+
+/*
+ * This function fills in xfs_mount_t fields based on mount args.
+ * Note: the superblock _has_ now been read in.
+ */
+STATIC int
+xfs_finish_flags(
+ struct xfs_mount_args *ap,
+ struct xfs_mount *mp)
+{
+ int ronly = (mp->m_flags & XFS_MOUNT_RDONLY);
+
+ /* Fail a mount where the logbuf is smaller then the log stripe */
+ if (xfs_sb_version_haslogv2(&mp->m_sb)) {
+ if ((ap->logbufsize <= 0) &&
+ (mp->m_sb.sb_logsunit > XLOG_BIG_RECORD_BSIZE)) {
+ mp->m_logbsize = mp->m_sb.sb_logsunit;
+ } else if (ap->logbufsize > 0 &&
+ ap->logbufsize < mp->m_sb.sb_logsunit) {
+ cmn_err(CE_WARN,
+ "XFS: logbuf size must be greater than or equal to log stripe size");
+ return XFS_ERROR(EINVAL);
+ }
+ } else {
+ /* Fail a mount if the logbuf is larger than 32K */
+ if (ap->logbufsize > XLOG_BIG_RECORD_BSIZE) {
+ cmn_err(CE_WARN,
+ "XFS: logbuf size for version 1 logs must be 16K or 32K");
+ return XFS_ERROR(EINVAL);
+ }
+ }
+
+ /*
+ * mkfs'ed attr2 will turn on attr2 mount unless explicitly
+ * told by noattr2 to turn it off
+ */
+ if (xfs_sb_version_hasattr2(&mp->m_sb) &&
+ !(ap->flags & XFSMNT_NOATTR2))
+ mp->m_flags |= XFS_MOUNT_ATTR2;
+
+ /*
+ * prohibit r/w mounts of read-only filesystems
+ */
+ if ((mp->m_sb.sb_flags & XFS_SBF_READONLY) && !ronly) {
+ cmn_err(CE_WARN,
+ "XFS: cannot mount a read-only filesystem as read-write");
+ return XFS_ERROR(EROFS);
+ }
+
+ /*
+ * check for shared mount.
+ */
+ if (ap->flags & XFSMNT_SHARED) {
+ if (!xfs_sb_version_hasshared(&mp->m_sb))
+ return XFS_ERROR(EINVAL);
+
+ /*
+ * For IRIX 6.5, shared mounts must have the shared
+ * version bit set, have the persistent readonly
+ * field set, must be version 0 and can only be mounted
+ * read-only.
+ */
+ if (!ronly || !(mp->m_sb.sb_flags & XFS_SBF_READONLY) ||
+ (mp->m_sb.sb_shared_vn != 0))
+ return XFS_ERROR(EINVAL);
+
+ mp->m_flags |= XFS_MOUNT_SHARED;
+
+ /*
+ * Shared XFS V0 can't deal with DMI. Return EINVAL.
+ */
+ if (mp->m_sb.sb_shared_vn == 0 && (ap->flags & XFSMNT_DMAPI))
+ return XFS_ERROR(EINVAL);
+ }
+
+ if (ap->flags & XFSMNT_UQUOTA) {
+ mp->m_qflags |= (XFS_UQUOTA_ACCT | XFS_UQUOTA_ACTIVE);
+ if (ap->flags & XFSMNT_UQUOTAENF)
+ mp->m_qflags |= XFS_UQUOTA_ENFD;
+ }
+
+ if (ap->flags & XFSMNT_GQUOTA) {
+ mp->m_qflags |= (XFS_GQUOTA_ACCT | XFS_GQUOTA_ACTIVE);
+ if (ap->flags & XFSMNT_GQUOTAENF)
+ mp->m_qflags |= XFS_OQUOTA_ENFD;
+ } else if (ap->flags & XFSMNT_PQUOTA) {
+ mp->m_qflags |= (XFS_PQUOTA_ACCT | XFS_PQUOTA_ACTIVE);
+ if (ap->flags & XFSMNT_PQUOTAENF)
+ mp->m_qflags |= XFS_OQUOTA_ENFD;
+ }
+
+ return 0;
+}
+
STATIC int
xfs_fs_fill_super(
struct super_block *sb,
{
struct inode *root;
struct xfs_mount *mp = NULL;
- struct xfs_mount_args *args = xfs_args_allocate(sb, silent);
- int error;
+ struct xfs_mount_args *args;
+ int flags = 0, error = ENOMEM;
+
+ args = xfs_args_allocate(sb, silent);
+ if (!args)
+ return -ENOMEM;
- mp = xfs_mount_init();
+ mp = kzalloc(sizeof(struct xfs_mount), GFP_KERNEL);
+ if (!mp)
+ goto out_free_args;
+ spin_lock_init(&mp->m_sb_lock);
+ mutex_init(&mp->m_ilock);
+ mutex_init(&mp->m_growlock);
+ atomic_set(&mp->m_active_trans, 0);
INIT_LIST_HEAD(&mp->m_sync_list);
spin_lock_init(&mp->m_sync_lock);
init_waitqueue_head(&mp->m_wait_single_sync_task);
error = xfs_parseargs(mp, (char *)data, args, 0);
if (error)
- goto fail_vfsop;
+ goto out_free_mp;
sb_min_blocksize(sb, BBSIZE);
+ sb->s_xattr = xfs_xattr_handlers;
sb->s_export_op = &xfs_export_operations;
sb->s_qcop = &xfs_quotactl_operations;
sb->s_op = &xfs_super_operations;
- error = xfs_mount(mp, args, NULL);
+ error = xfs_dmops_get(mp, args);
if (error)
- goto fail_vfsop;
+ goto out_free_mp;
+ error = xfs_qmops_get(mp, args);
+ if (error)
+ goto out_put_dmops;
+
+ if (args->flags & XFSMNT_QUIET)
+ flags |= XFS_MFSI_QUIET;
+
+ error = xfs_open_devices(mp, args);
+ if (error)
+ goto out_put_qmops;
+
+ if (xfs_icsb_init_counters(mp))
+ mp->m_flags |= XFS_MOUNT_NO_PERCPU_SB;
+
+ /*
+ * Setup flags based on mount(2) options and then the superblock
+ */
+ error = xfs_start_flags(args, mp);
+ if (error)
+ goto out_destroy_counters;
+ error = xfs_readsb(mp, flags);
+ if (error)
+ goto out_destroy_counters;
+ error = xfs_finish_flags(args, mp);
+ if (error)
+ goto out_free_sb;
+
+ error = xfs_setup_devices(mp);
+ if (error)
+ goto out_free_sb;
+
+ if (mp->m_flags & XFS_MOUNT_BARRIER)
+ xfs_mountfs_check_barriers(mp);
+
+ error = xfs_filestream_mount(mp);
+ if (error)
+ goto out_free_sb;
+
+ error = xfs_mountfs(mp, flags);
+ if (error)
+ goto out_filestream_unmount;
+
+ XFS_SEND_MOUNT(mp, DM_RIGHT_NULL, args->mtpt, args->fsname);
sb->s_dirt = 1;
sb->s_magic = XFS_SB_MAGIC;
xfs_itrace_exit(XFS_I(sb->s_root->d_inode));
- kmem_free(args, sizeof(*args));
+ kfree(args);
return 0;
-fail_vnrele:
+ out_filestream_unmount:
+ xfs_filestream_unmount(mp);
+ out_free_sb:
+ xfs_freesb(mp);
+ out_destroy_counters:
+ xfs_icsb_destroy_counters(mp);
+ xfs_close_devices(mp);
+ out_put_qmops:
+ xfs_qmops_put(mp);
+ out_put_dmops:
+ xfs_dmops_put(mp);
+ out_free_mp:
+ kfree(mp);
+ out_free_args:
+ kfree(args);
+ return -error;
+
+ fail_vnrele:
if (sb->s_root) {
dput(sb->s_root);
sb->s_root = NULL;
iput(root);
}
-fail_unmount:
- xfs_unmount(mp, 0, NULL);
+ fail_unmount:
+ /*
+ * Blow away any referenced inode in the filestreams cache.
+ * This can and will cause log traffic as inodes go inactive
+ * here.
+ */
+ xfs_filestream_unmount(mp);
-fail_vfsop:
- kmem_free(args, sizeof(*args));
- return -error;
+ XFS_bflush(mp->m_ddev_targp);
+ error = xfs_unmount_flush(mp, 0);
+ WARN_ON(error);
+
+ IRELE(mp->m_rootip);
+
+ xfs_unmountfs(mp);
+ goto out_destroy_counters;
}
STATIC int
.fs_flags = FS_REQUIRES_DEV,
};
+STATIC int __init
+xfs_alloc_trace_bufs(void)
+{
+#ifdef XFS_ALLOC_TRACE
+ xfs_alloc_trace_buf = ktrace_alloc(XFS_ALLOC_TRACE_SIZE, KM_MAYFAIL);
+ if (!xfs_alloc_trace_buf)
+ goto out;
+#endif
+#ifdef XFS_BMAP_TRACE
+ xfs_bmap_trace_buf = ktrace_alloc(XFS_BMAP_TRACE_SIZE, KM_MAYFAIL);
+ if (!xfs_bmap_trace_buf)
+ goto out_free_alloc_trace;
+#endif
+#ifdef XFS_BMBT_TRACE
+ xfs_bmbt_trace_buf = ktrace_alloc(XFS_BMBT_TRACE_SIZE, KM_MAYFAIL);
+ if (!xfs_bmbt_trace_buf)
+ goto out_free_bmap_trace;
+#endif
+#ifdef XFS_ATTR_TRACE
+ xfs_attr_trace_buf = ktrace_alloc(XFS_ATTR_TRACE_SIZE, KM_MAYFAIL);
+ if (!xfs_attr_trace_buf)
+ goto out_free_bmbt_trace;
+#endif
+#ifdef XFS_DIR2_TRACE
+ xfs_dir2_trace_buf = ktrace_alloc(XFS_DIR2_GTRACE_SIZE, KM_MAYFAIL);
+ if (!xfs_dir2_trace_buf)
+ goto out_free_attr_trace;
+#endif
+
+ return 0;
+
+#ifdef XFS_DIR2_TRACE
+ out_free_attr_trace:
+#endif
+#ifdef XFS_ATTR_TRACE
+ ktrace_free(xfs_attr_trace_buf);
+ out_free_bmbt_trace:
+#endif
+#ifdef XFS_BMBT_TRACE
+ ktrace_free(xfs_bmbt_trace_buf);
+ out_free_bmap_trace:
+#endif
+#ifdef XFS_BMAP_TRACE
+ ktrace_free(xfs_bmap_trace_buf);
+ out_free_alloc_trace:
+#endif
+#ifdef XFS_ALLOC_TRACE
+ ktrace_free(xfs_alloc_trace_buf);
+ out:
+#endif
+ return -ENOMEM;
+}
+
+STATIC void
+xfs_free_trace_bufs(void)
+{
+#ifdef XFS_DIR2_TRACE
+ ktrace_free(xfs_dir2_trace_buf);
+#endif
+#ifdef XFS_ATTR_TRACE
+ ktrace_free(xfs_attr_trace_buf);
+#endif
+#ifdef XFS_BMBT_TRACE
+ ktrace_free(xfs_bmbt_trace_buf);
+#endif
+#ifdef XFS_BMAP_TRACE
+ ktrace_free(xfs_bmap_trace_buf);
+#endif
+#ifdef XFS_ALLOC_TRACE
+ ktrace_free(xfs_alloc_trace_buf);
+#endif
+}
STATIC int __init
-init_xfs_fs( void )
+xfs_init_zones(void)
+{
+ xfs_vnode_zone = kmem_zone_init_flags(sizeof(bhv_vnode_t), "xfs_vnode",
+ KM_ZONE_HWALIGN | KM_ZONE_RECLAIM |
+ KM_ZONE_SPREAD,
+ xfs_fs_inode_init_once);
+ if (!xfs_vnode_zone)
+ goto out;
+
+ xfs_ioend_zone = kmem_zone_init(sizeof(xfs_ioend_t), "xfs_ioend");
+ if (!xfs_ioend_zone)
+ goto out_destroy_vnode_zone;
+
+ xfs_ioend_pool = mempool_create_slab_pool(4 * MAX_BUF_PER_PAGE,
+ xfs_ioend_zone);
+ if (!xfs_ioend_pool)
+ goto out_destroy_ioend_zone;
+
+ xfs_log_ticket_zone = kmem_zone_init(sizeof(xlog_ticket_t),
+ "xfs_log_ticket");
+ if (!xfs_log_ticket_zone)
+ goto out_destroy_ioend_pool;
+
+ xfs_bmap_free_item_zone = kmem_zone_init(sizeof(xfs_bmap_free_item_t),
+ "xfs_bmap_free_item");
+ if (!xfs_bmap_free_item_zone)
+ goto out_destroy_log_ticket_zone;
+ xfs_btree_cur_zone = kmem_zone_init(sizeof(xfs_btree_cur_t),
+ "xfs_btree_cur");
+ if (!xfs_btree_cur_zone)
+ goto out_destroy_bmap_free_item_zone;
+
+ xfs_da_state_zone = kmem_zone_init(sizeof(xfs_da_state_t),
+ "xfs_da_state");
+ if (!xfs_da_state_zone)
+ goto out_destroy_btree_cur_zone;
+
+ xfs_dabuf_zone = kmem_zone_init(sizeof(xfs_dabuf_t), "xfs_dabuf");
+ if (!xfs_dabuf_zone)
+ goto out_destroy_da_state_zone;
+
+ xfs_ifork_zone = kmem_zone_init(sizeof(xfs_ifork_t), "xfs_ifork");
+ if (!xfs_ifork_zone)
+ goto out_destroy_dabuf_zone;
+
+ xfs_trans_zone = kmem_zone_init(sizeof(xfs_trans_t), "xfs_trans");
+ if (!xfs_trans_zone)
+ goto out_destroy_ifork_zone;
+
+ /*
+ * The size of the zone allocated buf log item is the maximum
+ * size possible under XFS. This wastes a little bit of memory,
+ * but it is much faster.
+ */
+ xfs_buf_item_zone = kmem_zone_init((sizeof(xfs_buf_log_item_t) +
+ (((XFS_MAX_BLOCKSIZE / XFS_BLI_CHUNK) /
+ NBWORD) * sizeof(int))), "xfs_buf_item");
+ if (!xfs_buf_item_zone)
+ goto out_destroy_trans_zone;
+
+ xfs_efd_zone = kmem_zone_init((sizeof(xfs_efd_log_item_t) +
+ ((XFS_EFD_MAX_FAST_EXTENTS - 1) *
+ sizeof(xfs_extent_t))), "xfs_efd_item");
+ if (!xfs_efd_zone)
+ goto out_destroy_buf_item_zone;
+
+ xfs_efi_zone = kmem_zone_init((sizeof(xfs_efi_log_item_t) +
+ ((XFS_EFI_MAX_FAST_EXTENTS - 1) *
+ sizeof(xfs_extent_t))), "xfs_efi_item");
+ if (!xfs_efi_zone)
+ goto out_destroy_efd_zone;
+
+ xfs_inode_zone =
+ kmem_zone_init_flags(sizeof(xfs_inode_t), "xfs_inode",
+ KM_ZONE_HWALIGN | KM_ZONE_RECLAIM |
+ KM_ZONE_SPREAD, NULL);
+ if (!xfs_inode_zone)
+ goto out_destroy_efi_zone;
+
+ xfs_ili_zone =
+ kmem_zone_init_flags(sizeof(xfs_inode_log_item_t), "xfs_ili",
+ KM_ZONE_SPREAD, NULL);
+ if (!xfs_ili_zone)
+ goto out_destroy_inode_zone;
+
+#ifdef CONFIG_XFS_POSIX_ACL
+ xfs_acl_zone = kmem_zone_init(sizeof(xfs_acl_t), "xfs_acl");
+ if (!xfs_acl_zone)
+ goto out_destroy_ili_zone;
+#endif
+
+ return 0;
+
+#ifdef CONFIG_XFS_POSIX_ACL
+ out_destroy_ili_zone:
+#endif
+ kmem_zone_destroy(xfs_ili_zone);
+ out_destroy_inode_zone:
+ kmem_zone_destroy(xfs_inode_zone);
+ out_destroy_efi_zone:
+ kmem_zone_destroy(xfs_efi_zone);
+ out_destroy_efd_zone:
+ kmem_zone_destroy(xfs_efd_zone);
+ out_destroy_buf_item_zone:
+ kmem_zone_destroy(xfs_buf_item_zone);
+ out_destroy_trans_zone:
+ kmem_zone_destroy(xfs_trans_zone);
+ out_destroy_ifork_zone:
+ kmem_zone_destroy(xfs_ifork_zone);
+ out_destroy_dabuf_zone:
+ kmem_zone_destroy(xfs_dabuf_zone);
+ out_destroy_da_state_zone:
+ kmem_zone_destroy(xfs_da_state_zone);
+ out_destroy_btree_cur_zone:
+ kmem_zone_destroy(xfs_btree_cur_zone);
+ out_destroy_bmap_free_item_zone:
+ kmem_zone_destroy(xfs_bmap_free_item_zone);
+ out_destroy_log_ticket_zone:
+ kmem_zone_destroy(xfs_log_ticket_zone);
+ out_destroy_ioend_pool:
+ mempool_destroy(xfs_ioend_pool);
+ out_destroy_ioend_zone:
+ kmem_zone_destroy(xfs_ioend_zone);
+ out_destroy_vnode_zone:
+ kmem_zone_destroy(xfs_vnode_zone);
+ out:
+ return -ENOMEM;
+}
+
+STATIC void
+xfs_destroy_zones(void)
+{
+#ifdef CONFIG_XFS_POSIX_ACL
+ kmem_zone_destroy(xfs_acl_zone);
+#endif
+ kmem_zone_destroy(xfs_ili_zone);
+ kmem_zone_destroy(xfs_inode_zone);
+ kmem_zone_destroy(xfs_efi_zone);
+ kmem_zone_destroy(xfs_efd_zone);
+ kmem_zone_destroy(xfs_buf_item_zone);
+ kmem_zone_destroy(xfs_trans_zone);
+ kmem_zone_destroy(xfs_ifork_zone);
+ kmem_zone_destroy(xfs_dabuf_zone);
+ kmem_zone_destroy(xfs_da_state_zone);
+ kmem_zone_destroy(xfs_btree_cur_zone);
+ kmem_zone_destroy(xfs_bmap_free_item_zone);
+ kmem_zone_destroy(xfs_log_ticket_zone);
+ mempool_destroy(xfs_ioend_pool);
+ kmem_zone_destroy(xfs_ioend_zone);
+ kmem_zone_destroy(xfs_vnode_zone);
+
+}
+
+STATIC int __init
+init_xfs_fs(void)
{
int error;
static char message[] __initdata = KERN_INFO \
printk(message);
ktrace_init(64);
+ vn_init();
+ xfs_dir_startup();
error = xfs_init_zones();
- if (error < 0)
- goto undo_zones;
+ if (error)
+ goto out;
+
+ error = xfs_alloc_trace_bufs();
+ if (error)
+ goto out_destroy_zones;
+
+ error = xfs_mru_cache_init();
+ if (error)
+ goto out_free_trace_buffers;
+
+ error = xfs_filestream_init();
+ if (error)
+ goto out_mru_cache_uninit;
error = xfs_buf_init();
- if (error < 0)
- goto undo_buffers;
+ if (error)
+ goto out_filestream_uninit;
+
+ error = xfs_init_procfs();
+ if (error)
+ goto out_buf_terminate;
+
+ error = xfs_sysctl_register();
+ if (error)
+ goto out_cleanup_procfs;
- vn_init();
- xfs_init();
- uuid_init();
vfs_initquota();
error = register_filesystem(&xfs_fs_type);
if (error)
- goto undo_register;
+ goto out_sysctl_unregister;
return 0;
-undo_register:
+ out_sysctl_unregister:
+ xfs_sysctl_unregister();
+ out_cleanup_procfs:
+ xfs_cleanup_procfs();
+ out_buf_terminate:
xfs_buf_terminate();
-
-undo_buffers:
+ out_filestream_uninit:
+ xfs_filestream_uninit();
+ out_mru_cache_uninit:
+ xfs_mru_cache_uninit();
+ out_free_trace_buffers:
+ xfs_free_trace_bufs();
+ out_destroy_zones:
xfs_destroy_zones();
-
-undo_zones:
+ out:
return error;
}
STATIC void __exit
-exit_xfs_fs( void )
+exit_xfs_fs(void)
{
vfs_exitquota();
unregister_filesystem(&xfs_fs_type);
- xfs_cleanup();
+ xfs_sysctl_unregister();
+ xfs_cleanup_procfs();
xfs_buf_terminate();
+ xfs_filestream_uninit();
+ xfs_mru_cache_uninit();
+ xfs_free_trace_bufs();
xfs_destroy_zones();
ktrace_uninit();
}
extern void xfs_flush_inode(struct xfs_inode *);
extern void xfs_flush_device(struct xfs_inode *);
-extern int xfs_blkdev_get(struct xfs_mount *, const char *,
- struct block_device **);
-extern void xfs_blkdev_put(struct block_device *);
extern void xfs_blkdev_issue_flush(struct xfs_buftarg *);
extern const struct export_operations xfs_export_operations;
+extern struct xattr_handler *xfs_xattr_handlers[];
#define XFS_M(sb) ((struct xfs_mount *)((sb)->s_fs_info))
{}
};
-void
+int
xfs_sysctl_register(void)
{
xfs_table_header = register_sysctl_table(xfs_root_table);
+ if (!xfs_table_header)
+ return -ENOMEM;
+ return 0;
}
void
xfs_sysctl_unregister(void)
{
- if (xfs_table_header)
- unregister_sysctl_table(xfs_table_header);
+ unregister_sysctl_table(xfs_table_header);
}
extern xfs_param_t xfs_params;
#ifdef CONFIG_SYSCTL
-extern void xfs_sysctl_register(void);
+extern int xfs_sysctl_register(void);
extern void xfs_sysctl_unregister(void);
#else
-# define xfs_sysctl_register() do { } while (0)
+# define xfs_sysctl_register() (0)
# define xfs_sysctl_unregister() do { } while (0)
#endif /* CONFIG_SYSCTL */
xfs_do_force_shutdown(ip->i_mount, SHUTDOWN_DEVICE_REQ, f, l);
}
-/*
- * Revalidate the Linux inode from the XFS inode.
- * Note: i_size _not_ updated; we must hold the inode
- * semaphore when doing that - callers responsibility.
- */
-int
-vn_revalidate(
- bhv_vnode_t *vp)
-{
- struct inode *inode = vn_to_inode(vp);
- struct xfs_inode *ip = XFS_I(inode);
- struct xfs_mount *mp = ip->i_mount;
- unsigned long xflags;
-
- xfs_itrace_entry(ip);
-
- if (XFS_FORCED_SHUTDOWN(mp))
- return -EIO;
-
- xfs_ilock(ip, XFS_ILOCK_SHARED);
- inode->i_mode = ip->i_d.di_mode;
- inode->i_uid = ip->i_d.di_uid;
- inode->i_gid = ip->i_d.di_gid;
- inode->i_mtime.tv_sec = ip->i_d.di_mtime.t_sec;
- inode->i_mtime.tv_nsec = ip->i_d.di_mtime.t_nsec;
- inode->i_ctime.tv_sec = ip->i_d.di_ctime.t_sec;
- inode->i_ctime.tv_nsec = ip->i_d.di_ctime.t_nsec;
-
- xflags = xfs_ip2xflags(ip);
- if (xflags & XFS_XFLAG_IMMUTABLE)
- inode->i_flags |= S_IMMUTABLE;
- else
- inode->i_flags &= ~S_IMMUTABLE;
- if (xflags & XFS_XFLAG_APPEND)
- inode->i_flags |= S_APPEND;
- else
- inode->i_flags &= ~S_APPEND;
- if (xflags & XFS_XFLAG_SYNC)
- inode->i_flags |= S_SYNC;
- else
- inode->i_flags &= ~S_SYNC;
- if (xflags & XFS_XFLAG_NOATIME)
- inode->i_flags |= S_NOATIME;
- else
- inode->i_flags &= ~S_NOATIME;
- xfs_iunlock(ip, XFS_ILOCK_SHARED);
-
- xfs_iflags_clear(ip, XFS_IMODIFIED);
- return 0;
-}
/*
* Add a reference to a referenced vnode.
#define __XFS_VNODE_H__
struct file;
-struct bhv_vattr;
struct xfs_iomap;
struct attrlist_cursor_kern;
Prevent VM access to the pages until
the operation completes. */
-/*
- * Vnode attributes. va_mask indicates those attributes the caller
- * wants to set or extract.
- */
-typedef struct bhv_vattr {
- int va_mask; /* bit-mask of attributes present */
- mode_t va_mode; /* file access mode and type */
- xfs_nlink_t va_nlink; /* number of references to file */
- uid_t va_uid; /* owner user id */
- gid_t va_gid; /* owner group id */
- xfs_ino_t va_nodeid; /* file id */
- xfs_off_t va_size; /* file size in bytes */
- u_long va_blocksize; /* blocksize preferred for i/o */
- struct timespec va_atime; /* time of last access */
- struct timespec va_mtime; /* time of last modification */
- struct timespec va_ctime; /* time file changed */
- u_int va_gen; /* generation number of file */
- xfs_dev_t va_rdev; /* device the special file represents */
- __int64_t va_nblocks; /* number of blocks allocated */
- u_long va_xflags; /* random extended file flags */
- u_long va_extsize; /* file extent size */
- u_long va_nextents; /* number of extents in file */
- u_long va_anextents; /* number of attr extents in file */
- prid_t va_projid; /* project id */
-} bhv_vattr_t;
-
-/*
- * setattr or getattr attributes
- */
-#define XFS_AT_TYPE 0x00000001
-#define XFS_AT_MODE 0x00000002
-#define XFS_AT_UID 0x00000004
-#define XFS_AT_GID 0x00000008
-#define XFS_AT_FSID 0x00000010
-#define XFS_AT_NODEID 0x00000020
-#define XFS_AT_NLINK 0x00000040
-#define XFS_AT_SIZE 0x00000080
-#define XFS_AT_ATIME 0x00000100
-#define XFS_AT_MTIME 0x00000200
-#define XFS_AT_CTIME 0x00000400
-#define XFS_AT_RDEV 0x00000800
-#define XFS_AT_BLKSIZE 0x00001000
-#define XFS_AT_NBLOCKS 0x00002000
-#define XFS_AT_VCODE 0x00004000
-#define XFS_AT_MAC 0x00008000
-#define XFS_AT_UPDATIME 0x00010000
-#define XFS_AT_UPDMTIME 0x00020000
-#define XFS_AT_UPDCTIME 0x00040000
-#define XFS_AT_ACL 0x00080000
-#define XFS_AT_CAP 0x00100000
-#define XFS_AT_INF 0x00200000
-#define XFS_AT_XFLAGS 0x00400000
-#define XFS_AT_EXTSIZE 0x00800000
-#define XFS_AT_NEXTENTS 0x01000000
-#define XFS_AT_ANEXTENTS 0x02000000
-#define XFS_AT_PROJID 0x04000000
-#define XFS_AT_SIZE_NOPERM 0x08000000
-#define XFS_AT_GENCOUNT 0x10000000
-
-#define XFS_AT_ALL (XFS_AT_TYPE|XFS_AT_MODE|XFS_AT_UID|XFS_AT_GID|\
- XFS_AT_FSID|XFS_AT_NODEID|XFS_AT_NLINK|XFS_AT_SIZE|\
- XFS_AT_ATIME|XFS_AT_MTIME|XFS_AT_CTIME|XFS_AT_RDEV|\
- XFS_AT_BLKSIZE|XFS_AT_NBLOCKS|XFS_AT_VCODE|XFS_AT_MAC|\
- XFS_AT_ACL|XFS_AT_CAP|XFS_AT_INF|XFS_AT_XFLAGS|XFS_AT_EXTSIZE|\
- XFS_AT_NEXTENTS|XFS_AT_ANEXTENTS|XFS_AT_PROJID|XFS_AT_GENCOUNT)
-
-#define XFS_AT_STAT (XFS_AT_TYPE|XFS_AT_MODE|XFS_AT_UID|XFS_AT_GID|\
- XFS_AT_FSID|XFS_AT_NODEID|XFS_AT_NLINK|XFS_AT_SIZE|\
- XFS_AT_ATIME|XFS_AT_MTIME|XFS_AT_CTIME|XFS_AT_RDEV|\
- XFS_AT_BLKSIZE|XFS_AT_NBLOCKS|XFS_AT_PROJID)
-
-#define XFS_AT_TIMES (XFS_AT_ATIME|XFS_AT_MTIME|XFS_AT_CTIME)
-
-#define XFS_AT_UPDTIMES (XFS_AT_UPDATIME|XFS_AT_UPDMTIME|XFS_AT_UPDCTIME)
-
-#define XFS_AT_NOSET (XFS_AT_NLINK|XFS_AT_RDEV|XFS_AT_FSID|XFS_AT_NODEID|\
- XFS_AT_TYPE|XFS_AT_BLKSIZE|XFS_AT_NBLOCKS|XFS_AT_VCODE|\
- XFS_AT_NEXTENTS|XFS_AT_ANEXTENTS|XFS_AT_GENCOUNT)
extern void vn_init(void);
-extern int vn_revalidate(bhv_vnode_t *);
/*
* Yeah, these don't take vnode anymore at all, all this should be
#define VN_DIRTY(vp) mapping_tagged(vn_to_inode(vp)->i_mapping, \
PAGECACHE_TAG_DIRTY)
-/*
- * Flags to vop_setattr/getattr.
- */
-#define ATTR_UTIME 0x01 /* non-default utime(2) request */
-#define ATTR_DMI 0x08 /* invocation from a DMI function */
-#define ATTR_LAZY 0x80 /* set/get attributes lazily */
-#define ATTR_NONBLOCK 0x100 /* return EAGAIN if operation would block */
-#define ATTR_NOLOCK 0x200 /* Don't grab any conflicting locks */
-#define ATTR_NOSIZETOK 0x400 /* Don't get the SIZE token */
/*
* Tracking vnode activity.
--- /dev/null
+/*
+ * Copyright (C) 2008 Christoph Hellwig.
+ * Portions Copyright (C) 2000-2008 Silicon Graphics, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it would be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write the Free Software Foundation,
+ * Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include "xfs.h"
+#include "xfs_da_btree.h"
+#include "xfs_bmap_btree.h"
+#include "xfs_inode.h"
+#include "xfs_attr.h"
+#include "xfs_attr_leaf.h"
+#include "xfs_acl.h"
+#include "xfs_vnodeops.h"
+
+#include <linux/posix_acl_xattr.h>
+#include <linux/xattr.h>
+
+
+/*
+ * ACL handling. Should eventually be moved into xfs_acl.c
+ */
+
+static int
+xfs_decode_acl(const char *name)
+{
+ if (strcmp(name, "posix_acl_access") == 0)
+ return _ACL_TYPE_ACCESS;
+ else if (strcmp(name, "posix_acl_default") == 0)
+ return _ACL_TYPE_DEFAULT;
+ return -EINVAL;
+}
+
+/*
+ * Get system extended attributes which at the moment only
+ * includes Posix ACLs.
+ */
+static int
+xfs_xattr_system_get(struct inode *inode, const char *name,
+ void *buffer, size_t size)
+{
+ int acl;
+
+ acl = xfs_decode_acl(name);
+ if (acl < 0)
+ return acl;
+
+ return xfs_acl_vget(inode, buffer, size, acl);
+}
+
+static int
+xfs_xattr_system_set(struct inode *inode, const char *name,
+ const void *value, size_t size, int flags)
+{
+ int acl;
+
+ acl = xfs_decode_acl(name);
+ if (acl < 0)
+ return acl;
+ if (flags & XATTR_CREATE)
+ return -EINVAL;
+
+ if (!value)
+ return xfs_acl_vremove(inode, acl);
+
+ return xfs_acl_vset(inode, (void *)value, size, acl);
+}
+
+static struct xattr_handler xfs_xattr_system_handler = {
+ .prefix = XATTR_SYSTEM_PREFIX,
+ .get = xfs_xattr_system_get,
+ .set = xfs_xattr_system_set,
+};
+
+
+/*
+ * Real xattr handling. The only difference between the namespaces is
+ * a flag passed to the low-level attr code.
+ */
+
+static int
+__xfs_xattr_get(struct inode *inode, const char *name,
+ void *value, size_t size, int xflags)
+{
+ struct xfs_inode *ip = XFS_I(inode);
+ int error, asize = size;
+
+ if (strcmp(name, "") == 0)
+ return -EINVAL;
+
+ /* Convert Linux syscall to XFS internal ATTR flags */
+ if (!size) {
+ xflags |= ATTR_KERNOVAL;
+ value = NULL;
+ }
+
+ error = -xfs_attr_get(ip, name, value, &asize, xflags);
+ if (error)
+ return error;
+ return asize;
+}
+
+static int
+__xfs_xattr_set(struct inode *inode, const char *name, const void *value,
+ size_t size, int flags, int xflags)
+{
+ struct xfs_inode *ip = XFS_I(inode);
+
+ if (strcmp(name, "") == 0)
+ return -EINVAL;
+
+ /* Convert Linux syscall to XFS internal ATTR flags */
+ if (flags & XATTR_CREATE)
+ xflags |= ATTR_CREATE;
+ if (flags & XATTR_REPLACE)
+ xflags |= ATTR_REPLACE;
+
+ if (!value)
+ return -xfs_attr_remove(ip, name, xflags);
+ return -xfs_attr_set(ip, name, (void *)value, size, xflags);
+}
+
+static int
+xfs_xattr_user_get(struct inode *inode, const char *name,
+ void *value, size_t size)
+{
+ return __xfs_xattr_get(inode, name, value, size, 0);
+}
+
+static int
+xfs_xattr_user_set(struct inode *inode, const char *name,
+ const void *value, size_t size, int flags)
+{
+ return __xfs_xattr_set(inode, name, value, size, flags, 0);
+}
+
+static struct xattr_handler xfs_xattr_user_handler = {
+ .prefix = XATTR_USER_PREFIX,
+ .get = xfs_xattr_user_get,
+ .set = xfs_xattr_user_set,
+};
+
+
+static int
+xfs_xattr_trusted_get(struct inode *inode, const char *name,
+ void *value, size_t size)
+{
+ return __xfs_xattr_get(inode, name, value, size, ATTR_ROOT);
+}
+
+static int
+xfs_xattr_trusted_set(struct inode *inode, const char *name,
+ const void *value, size_t size, int flags)
+{
+ return __xfs_xattr_set(inode, name, value, size, flags, ATTR_ROOT);
+}
+
+static struct xattr_handler xfs_xattr_trusted_handler = {
+ .prefix = XATTR_TRUSTED_PREFIX,
+ .get = xfs_xattr_trusted_get,
+ .set = xfs_xattr_trusted_set,
+};
+
+
+static int
+xfs_xattr_secure_get(struct inode *inode, const char *name,
+ void *value, size_t size)
+{
+ return __xfs_xattr_get(inode, name, value, size, ATTR_SECURE);
+}
+
+static int
+xfs_xattr_secure_set(struct inode *inode, const char *name,
+ const void *value, size_t size, int flags)
+{
+ return __xfs_xattr_set(inode, name, value, size, flags, ATTR_SECURE);
+}
+
+static struct xattr_handler xfs_xattr_security_handler = {
+ .prefix = XATTR_SECURITY_PREFIX,
+ .get = xfs_xattr_secure_get,
+ .set = xfs_xattr_secure_set,
+};
+
+
+struct xattr_handler *xfs_xattr_handlers[] = {
+ &xfs_xattr_user_handler,
+ &xfs_xattr_trusted_handler,
+ &xfs_xattr_security_handler,
+ &xfs_xattr_system_handler,
+ NULL
+};
+
+static unsigned int xfs_xattr_prefix_len(int flags)
+{
+ if (flags & XFS_ATTR_SECURE)
+ return sizeof("security");
+ else if (flags & XFS_ATTR_ROOT)
+ return sizeof("trusted");
+ else
+ return sizeof("user");
+}
+
+static const char *xfs_xattr_prefix(int flags)
+{
+ if (flags & XFS_ATTR_SECURE)
+ return xfs_xattr_security_handler.prefix;
+ else if (flags & XFS_ATTR_ROOT)
+ return xfs_xattr_trusted_handler.prefix;
+ else
+ return xfs_xattr_user_handler.prefix;
+}
+
+static int
+xfs_xattr_put_listent(struct xfs_attr_list_context *context, int flags,
+ char *name, int namelen, int valuelen, char *value)
+{
+ unsigned int prefix_len = xfs_xattr_prefix_len(flags);
+ char *offset;
+ int arraytop;
+
+ ASSERT(context->count >= 0);
+
+ /*
+ * Only show root namespace entries if we are actually allowed to
+ * see them.
+ */
+ if ((flags & XFS_ATTR_ROOT) && !capable(CAP_SYS_ADMIN))
+ return 0;
+
+ arraytop = context->count + prefix_len + namelen + 1;
+ if (arraytop > context->firstu) {
+ context->count = -1; /* insufficient space */
+ return 1;
+ }
+ offset = (char *)context->alist + context->count;
+ strncpy(offset, xfs_xattr_prefix(flags), prefix_len);
+ offset += prefix_len;
+ strncpy(offset, name, namelen); /* real name */
+ offset += namelen;
+ *offset = '\0';
+ context->count += prefix_len + namelen + 1;
+ return 0;
+}
+
+static int
+xfs_xattr_put_listent_sizes(struct xfs_attr_list_context *context, int flags,
+ char *name, int namelen, int valuelen, char *value)
+{
+ context->count += xfs_xattr_prefix_len(flags) + namelen + 1;
+ return 0;
+}
+
+static int
+list_one_attr(const char *name, const size_t len, void *data,
+ size_t size, ssize_t *result)
+{
+ char *p = data + *result;
+
+ *result += len;
+ if (!size)
+ return 0;
+ if (*result > size)
+ return -ERANGE;
+
+ strcpy(p, name);
+ return 0;
+}
+
+ssize_t
+xfs_vn_listxattr(struct dentry *dentry, char *data, size_t size)
+{
+ struct xfs_attr_list_context context;
+ struct attrlist_cursor_kern cursor = { 0 };
+ struct inode *inode = dentry->d_inode;
+ int error;
+
+ /*
+ * First read the regular on-disk attributes.
+ */
+ memset(&context, 0, sizeof(context));
+ context.dp = XFS_I(inode);
+ context.cursor = &cursor;
+ context.resynch = 1;
+ context.alist = data;
+ context.bufsize = size;
+ context.firstu = context.bufsize;
+
+ if (size)
+ context.put_listent = xfs_xattr_put_listent;
+ else
+ context.put_listent = xfs_xattr_put_listent_sizes;
+
+ xfs_attr_list_int(&context);
+ if (context.count < 0)
+ return -ERANGE;
+
+ /*
+ * Then add the two synthetic ACL attributes.
+ */
+ if (xfs_acl_vhasacl_access(inode)) {
+ error = list_one_attr(POSIX_ACL_XATTR_ACCESS,
+ strlen(POSIX_ACL_XATTR_ACCESS) + 1,
+ data, size, &context.count);
+ if (error)
+ return error;
+ }
+
+ if (xfs_acl_vhasacl_default(inode)) {
+ error = list_one_attr(POSIX_ACL_XATTR_DEFAULT,
+ strlen(POSIX_ACL_XATTR_DEFAULT) + 1,
+ data, size, &context.count);
+ if (error)
+ return error;
+ }
+
+ return context.count;
+}
/* ARGSUSED */
int
xfs_qm_dqpurge(
- xfs_dquot_t *dqp,
- uint flags)
+ xfs_dquot_t *dqp)
{
xfs_dqhash_t *thishash;
xfs_mount_t *mp = dqp->q_mount;
extern void xfs_qm_dqdestroy(xfs_dquot_t *);
extern int xfs_qm_dqflush(xfs_dquot_t *, uint);
-extern int xfs_qm_dqpurge(xfs_dquot_t *, uint);
+extern int xfs_qm_dqpurge(xfs_dquot_t *);
extern void xfs_qm_dqunpin_wait(xfs_dquot_t *);
extern int xfs_qm_dqlock_nowait(xfs_dquot_t *);
extern int xfs_qm_dqflock_nowait(xfs_dquot_t *);
* xfs_trans_delete_ail() drops the AIL lock.
*/
xfs_trans_delete_ail(qfs->qql_item.li_mountp, (xfs_log_item_t *)qfs);
- kmem_free(qfs, sizeof(xfs_qoff_logitem_t));
- kmem_free(qfe, sizeof(xfs_qoff_logitem_t));
+ kmem_free(qfs);
+ kmem_free(qfe);
return (xfs_lsn_t)-1;
}
xfs_qm_list_destroy(&(xqm->qm_usr_dqhtable[i]));
xfs_qm_list_destroy(&(xqm->qm_grp_dqhtable[i]));
}
- kmem_free(xqm->qm_usr_dqhtable, hsize * sizeof(xfs_dqhash_t));
- kmem_free(xqm->qm_grp_dqhtable, hsize * sizeof(xfs_dqhash_t));
+ kmem_free(xqm->qm_usr_dqhtable);
+ kmem_free(xqm->qm_grp_dqhtable);
xqm->qm_usr_dqhtable = NULL;
xqm->qm_grp_dqhtable = NULL;
xqm->qm_dqhashmask = 0;
#ifdef DEBUG
mutex_destroy(&qcheck_lock);
#endif
- kmem_free(xqm, sizeof(xfs_qm_t));
+ kmem_free(xqm);
}
/*
}
}
if (uqp) {
- XFS_PURGE_INODE(uqp);
+ IRELE(uqp);
mp->m_quotainfo->qi_uquotaip = NULL;
}
if (gqp) {
- XFS_PURGE_INODE(gqp);
+ IRELE(gqp);
mp->m_quotainfo->qi_gquotaip = NULL;
}
out:
* freelist in INACTIVE state.
*/
nextdqp = dqp->MPL_NEXT;
- nmisses += xfs_qm_dqpurge(dqp, flags);
+ nmisses += xfs_qm_dqpurge(dqp);
dqp = nextdqp;
}
xfs_qm_mplist_unlock(mp);
* and change the superblock accordingly.
*/
if ((error = xfs_qm_init_quotainos(mp))) {
- kmem_free(qinf, sizeof(xfs_quotainfo_t));
+ kmem_free(qinf);
mp->m_quotainfo = NULL;
return error;
}
xfs_qm_list_destroy(&qi->qi_dqlist);
if (qi->qi_uquotaip) {
- XFS_PURGE_INODE(qi->qi_uquotaip);
+ IRELE(qi->qi_uquotaip);
qi->qi_uquotaip = NULL; /* paranoia */
}
if (qi->qi_gquotaip) {
- XFS_PURGE_INODE(qi->qi_gquotaip);
+ IRELE(qi->qi_gquotaip);
qi->qi_gquotaip = NULL;
}
mutex_destroy(&qi->qi_quotaofflock);
- kmem_free(qi, sizeof(xfs_quotainfo_t));
+ kmem_free(qi);
mp->m_quotainfo = NULL;
}
* locked exclusively and joined to the transaction already.
*/
ASSERT(xfs_isilocked(*ip, XFS_ILOCK_EXCL));
- VN_HOLD(XFS_ITOV((*ip)));
+ IHOLD(*ip);
/*
* Make the changes in the superblock, and log those too.
break;
} while (nmaps > 0);
- kmem_free(map, XFS_DQITER_MAP_SIZE * sizeof(*map));
+ kmem_free(map);
return error;
}
* if we don't need them anymore.
*/
if ((dqtype & XFS_QMOPT_UQUOTA) && XFS_QI_UQIP(mp)) {
- XFS_PURGE_INODE(XFS_QI_UQIP(mp));
+ IRELE(XFS_QI_UQIP(mp));
XFS_QI_UQIP(mp) = NULL;
}
if ((dqtype & (XFS_QMOPT_GQUOTA|XFS_QMOPT_PQUOTA)) && XFS_QI_GQIP(mp)) {
- XFS_PURGE_INODE(XFS_QI_GQIP(mp));
+ IRELE(XFS_QI_GQIP(mp));
XFS_QI_GQIP(mp) = NULL;
}
out_error:
for (d = (xfs_dqtest_t *) h1->qh_next; d != NULL; ) {
xfs_dqtest_cmp(d);
e = (xfs_dqtest_t *) d->HL_NEXT;
- kmem_free(d, sizeof(xfs_dqtest_t));
+ kmem_free(d);
d = e;
}
h1 = &qmtest_gdqtab[i];
for (d = (xfs_dqtest_t *) h1->qh_next; d != NULL; ) {
xfs_dqtest_cmp(d);
e = (xfs_dqtest_t *) d->HL_NEXT;
- kmem_free(d, sizeof(xfs_dqtest_t));
+ kmem_free(d);
d = e;
}
}
} else {
cmn_err(CE_DEBUG, "******** quotacheck successful! ********");
}
- kmem_free(qmtest_udqtab, qmtest_hashmask * sizeof(xfs_dqhash_t));
- kmem_free(qmtest_gdqtab, qmtest_hashmask * sizeof(xfs_dqhash_t));
+ kmem_free(qmtest_udqtab);
+ kmem_free(qmtest_gdqtab);
mutex_unlock(&qcheck_lock);
return (qmtest_nfails);
}
#define XFS_IS_SUSER_DQUOT(dqp) \
(!((dqp)->q_core.d_id))
-#define XFS_PURGE_INODE(ip) \
- IRELE(ip);
-
#define DQFLAGTO_TYPESTR(d) (((d)->dq_flags & XFS_DQ_USER) ? "USR" : \
(((d)->dq_flags & XFS_DQ_GROUP) ? "GRP" : \
(((d)->dq_flags & XFS_DQ_PROJ) ? "PRJ":"???")))
if (sleep & KM_SLEEP)
panic("ktrace_alloc: NULL memory on KM_SLEEP request!");
- kmem_free(ktp, sizeof(*ktp));
+ kmem_free(ktp);
return NULL;
}
} else {
entries_size = (int)(ktp->kt_nentries * sizeof(ktrace_entry_t));
- kmem_free(ktp->kt_entries, entries_size);
+ kmem_free(ktp->kt_entries);
}
kmem_zone_free(ktrace_hdr_zone, ktp);
*/
#include <xfs.h>
-static mutex_t uuid_monitor;
+static DEFINE_MUTEX(uuid_monitor);
static int uuid_table_size;
static uuid_t *uuid_table;
ASSERT(i < uuid_table_size);
mutex_unlock(&uuid_monitor);
}
-
-void __init
-uuid_init(void)
-{
- mutex_init(&uuid_monitor);
-}
unsigned char __u_bits[16];
} uuid_t;
-extern void uuid_init(void);
extern void uuid_create_nil(uuid_t *uuid);
extern int uuid_is_nil(uuid_t *uuid);
extern int uuid_equal(uuid_t *uuid1, uuid_t *uuid2);
/* If the file has no ACL return -1. */
rval = sizeof(xfs_acl_t);
- if (xfs_attr_fetch(ip, &acl_name, (char *)acl, &rval,
- ATTR_ROOT | ATTR_KERNACCESS)) {
+ if (xfs_attr_fetch(ip, &acl_name, (char *)acl, &rval, ATTR_ROOT)) {
_ACL_FREE(acl);
return -1;
}
xfs_acl_t *acl,
int *basicperms)
{
- bhv_vattr_t va;
+ struct iattr iattr;
xfs_acl_entry_t *ap;
xfs_acl_entry_t *gap = NULL;
int i, nomask = 1;
* Copy the u::, g::, o::, and m:: bits from the ACL into the
* mode. The m:: bits take precedence over the g:: bits.
*/
- va.va_mask = XFS_AT_MODE;
- va.va_mode = xfs_vtoi(vp)->i_d.di_mode;
- va.va_mode &= ~(S_IRWXU|S_IRWXG|S_IRWXO);
+ iattr.ia_valid = ATTR_MODE;
+ iattr.ia_mode = xfs_vtoi(vp)->i_d.di_mode;
+ iattr.ia_mode &= ~(S_IRWXU|S_IRWXG|S_IRWXO);
ap = acl->acl_entry;
for (i = 0; i < acl->acl_cnt; ++i) {
switch (ap->ae_tag) {
case ACL_USER_OBJ:
- va.va_mode |= ap->ae_perm << 6;
+ iattr.ia_mode |= ap->ae_perm << 6;
break;
case ACL_GROUP_OBJ:
gap = ap;
break;
case ACL_MASK: /* more than just standard modes */
nomask = 0;
- va.va_mode |= ap->ae_perm << 3;
+ iattr.ia_mode |= ap->ae_perm << 3;
*basicperms = 0;
break;
case ACL_OTHER:
- va.va_mode |= ap->ae_perm;
+ iattr.ia_mode |= ap->ae_perm;
break;
default: /* more than just standard modes */
*basicperms = 0;
/* Set the group bits from ACL_GROUP_OBJ if there's no ACL_MASK */
if (gap && nomask)
- va.va_mode |= gap->ae_perm << 3;
+ iattr.ia_mode |= gap->ae_perm << 3;
- return xfs_setattr(xfs_vtoi(vp), &va, 0, sys_cred);
+ return xfs_setattr(xfs_vtoi(vp), &iattr, 0, sys_cred);
}
/*
#define SGI_ACL_FILE_SIZE (sizeof(SGI_ACL_FILE)-1)
#define SGI_ACL_DEFAULT_SIZE (sizeof(SGI_ACL_DEFAULT)-1)
+#define _ACL_TYPE_ACCESS 1
+#define _ACL_TYPE_DEFAULT 2
#ifdef CONFIG_XFS_POSIX_ACL
extern int xfs_acl_vget(bhv_vnode_t *, void *, size_t, int);
extern int xfs_acl_vremove(bhv_vnode_t *, int);
-#define _ACL_TYPE_ACCESS 1
-#define _ACL_TYPE_DEFAULT 2
#define _ACL_PERM_INVALID(perm) ((perm) & ~(ACL_READ|ACL_WRITE|ACL_EXECUTE))
#define _ACL_INHERIT(c,m,d) (xfs_acl_inherit(c,m,d))
* Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
-#include <linux/capability.h>
-
#include "xfs.h"
#include "xfs_fs.h"
#include "xfs_types.h"
* Provide the external interfaces to manage attribute lists.
*/
-#define ATTR_SYSCOUNT 2
-static struct attrnames posix_acl_access;
-static struct attrnames posix_acl_default;
-static struct attrnames *attr_system_names[ATTR_SYSCOUNT];
-
/*========================================================================
* Function prototypes for the kernel.
*========================================================================*/
return 0;
}
+STATIC int
+xfs_inode_hasattr(
+ struct xfs_inode *ip)
+{
+ if (!XFS_IFORK_Q(ip) ||
+ (ip->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
+ ip->i_d.di_anextents == 0))
+ return 0;
+ return 1;
+}
+
/*========================================================================
* Overall external interface routines.
*========================================================================*/
xfs_da_args_t args;
int error;
- if ((XFS_IFORK_Q(ip) == 0) ||
- (ip->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- ip->i_d.di_anextents == 0))
- return(ENOATTR);
+ if (!xfs_inode_hasattr(ip))
+ return ENOATTR;
/*
* Fill in the arg structure for this request.
/*
* Decide on what work routines to call based on the inode size.
*/
- if (XFS_IFORK_Q(ip) == 0 ||
- (ip->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- ip->i_d.di_anextents == 0)) {
- error = XFS_ERROR(ENOATTR);
- } else if (ip->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) {
+ if (ip->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) {
error = xfs_attr_shortform_getvalue(&args);
} else if (xfs_bmap_one_block(ip, XFS_ATTR_FORK)) {
error = xfs_attr_leaf_get(&args);
args.firstblock = &firstblock;
args.flist = &flist;
args.whichfork = XFS_ATTR_FORK;
- args.addname = 1;
- args.oknoent = 1;
+ args.op_flags = XFS_DA_OP_ADDNAME | XFS_DA_OP_OKNOENT;
/*
* Determine space new attribute will use, and if it would be
/*
* Decide on what work routines to call based on the inode size.
*/
- if (XFS_IFORK_Q(dp) == 0 ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- dp->i_d.di_anextents == 0)) {
+ if (!xfs_inode_hasattr(dp)) {
error = XFS_ERROR(ENOATTR);
goto out;
}
return error;
xfs_ilock(dp, XFS_ILOCK_SHARED);
- if (XFS_IFORK_Q(dp) == 0 ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- dp->i_d.di_anextents == 0)) {
+ if (!xfs_inode_hasattr(dp)) {
xfs_iunlock(dp, XFS_ILOCK_SHARED);
- return(XFS_ERROR(ENOATTR));
+ return XFS_ERROR(ENOATTR);
}
xfs_iunlock(dp, XFS_ILOCK_SHARED);
return xfs_attr_remove_int(dp, &xname, flags);
}
-STATIC int
+int
xfs_attr_list_int(xfs_attr_list_context_t *context)
{
int error;
xfs_inode_t *dp = context->dp;
+ XFS_STATS_INC(xs_attr_list);
+
+ if (XFS_FORCED_SHUTDOWN(dp->i_mount))
+ return EIO;
+
+ xfs_ilock(dp, XFS_ILOCK_SHARED);
+ xfs_attr_trace_l_c("syscall start", context);
+
/*
* Decide on what work routines to call based on the inode size.
*/
- if (XFS_IFORK_Q(dp) == 0 ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- dp->i_d.di_anextents == 0)) {
+ if (!xfs_inode_hasattr(dp)) {
error = 0;
} else if (dp->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) {
error = xfs_attr_shortform_list(context);
} else {
error = xfs_attr_node_list(context);
}
+
+ xfs_iunlock(dp, XFS_ILOCK_SHARED);
+ xfs_attr_trace_l_c("syscall end", context);
+
return error;
}
*/
/*ARGSUSED*/
STATIC int
-xfs_attr_put_listent(xfs_attr_list_context_t *context, attrnames_t *namesp,
+xfs_attr_put_listent(xfs_attr_list_context_t *context, int flags,
char *name, int namelen,
int valuelen, char *value)
{
+ struct attrlist *alist = (struct attrlist *)context->alist;
attrlist_ent_t *aep;
int arraytop;
ASSERT(!(context->flags & ATTR_KERNOVAL));
ASSERT(context->count >= 0);
ASSERT(context->count < (ATTR_MAX_VALUELEN/8));
- ASSERT(context->firstu >= sizeof(*context->alist));
+ ASSERT(context->firstu >= sizeof(*alist));
ASSERT(context->firstu <= context->bufsize);
- arraytop = sizeof(*context->alist) +
- context->count * sizeof(context->alist->al_offset[0]);
+ /*
+ * Only list entries in the right namespace.
+ */
+ if (((context->flags & ATTR_SECURE) == 0) !=
+ ((flags & XFS_ATTR_SECURE) == 0))
+ return 0;
+ if (((context->flags & ATTR_ROOT) == 0) !=
+ ((flags & XFS_ATTR_ROOT) == 0))
+ return 0;
+
+ arraytop = sizeof(*alist) +
+ context->count * sizeof(alist->al_offset[0]);
context->firstu -= ATTR_ENTSIZE(namelen);
if (context->firstu < arraytop) {
xfs_attr_trace_l_c("buffer full", context);
- context->alist->al_more = 1;
+ alist->al_more = 1;
context->seen_enough = 1;
return 1;
}
- aep = (attrlist_ent_t *)&(((char *)context->alist)[ context->firstu ]);
+ aep = (attrlist_ent_t *)&context->alist[context->firstu];
aep->a_valuelen = valuelen;
memcpy(aep->a_name, name, namelen);
- aep->a_name[ namelen ] = 0;
- context->alist->al_offset[ context->count++ ] = context->firstu;
- context->alist->al_count = context->count;
+ aep->a_name[namelen] = 0;
+ alist->al_offset[context->count++] = context->firstu;
+ alist->al_count = context->count;
xfs_attr_trace_l_c("add", context);
return 0;
}
-STATIC int
-xfs_attr_kern_list(xfs_attr_list_context_t *context, attrnames_t *namesp,
- char *name, int namelen,
- int valuelen, char *value)
-{
- char *offset;
- int arraytop;
-
- ASSERT(context->count >= 0);
-
- arraytop = context->count + namesp->attr_namelen + namelen + 1;
- if (arraytop > context->firstu) {
- context->count = -1; /* insufficient space */
- return 1;
- }
- offset = (char *)context->alist + context->count;
- strncpy(offset, namesp->attr_name, namesp->attr_namelen);
- offset += namesp->attr_namelen;
- strncpy(offset, name, namelen); /* real name */
- offset += namelen;
- *offset = '\0';
- context->count += namesp->attr_namelen + namelen + 1;
- return 0;
-}
-
-/*ARGSUSED*/
-STATIC int
-xfs_attr_kern_list_sizes(xfs_attr_list_context_t *context, attrnames_t *namesp,
- char *name, int namelen,
- int valuelen, char *value)
-{
- context->count += namesp->attr_namelen + namelen + 1;
- return 0;
-}
-
/*
* Generate a list of extended attribute names and optionally
* also value lengths. Positive return value follows the XFS
attrlist_cursor_kern_t *cursor)
{
xfs_attr_list_context_t context;
+ struct attrlist *alist;
int error;
- XFS_STATS_INC(xs_attr_list);
-
/*
* Validate the cursor.
*/
/*
* Initialize the output buffer.
*/
+ memset(&context, 0, sizeof(context));
context.dp = dp;
context.cursor = cursor;
- context.count = 0;
- context.dupcnt = 0;
context.resynch = 1;
context.flags = flags;
- context.seen_enough = 0;
- context.alist = (attrlist_t *)buffer;
- context.put_value = 0;
-
- if (flags & ATTR_KERNAMELS) {
- context.bufsize = bufsize;
- context.firstu = context.bufsize;
- if (flags & ATTR_KERNOVAL)
- context.put_listent = xfs_attr_kern_list_sizes;
- else
- context.put_listent = xfs_attr_kern_list;
- } else {
- context.bufsize = (bufsize & ~(sizeof(int)-1)); /* align */
- context.firstu = context.bufsize;
- context.alist->al_count = 0;
- context.alist->al_more = 0;
- context.alist->al_offset[0] = context.bufsize;
- context.put_listent = xfs_attr_put_listent;
- }
+ context.alist = buffer;
+ context.bufsize = (bufsize & ~(sizeof(int)-1)); /* align */
+ context.firstu = context.bufsize;
+ context.put_listent = xfs_attr_put_listent;
- if (XFS_FORCED_SHUTDOWN(dp->i_mount))
- return EIO;
-
- xfs_ilock(dp, XFS_ILOCK_SHARED);
- xfs_attr_trace_l_c("syscall start", &context);
+ alist = (struct attrlist *)context.alist;
+ alist->al_count = 0;
+ alist->al_more = 0;
+ alist->al_offset[0] = context.bufsize;
error = xfs_attr_list_int(&context);
-
- xfs_iunlock(dp, XFS_ILOCK_SHARED);
- xfs_attr_trace_l_c("syscall end", &context);
-
- if (context.flags & (ATTR_KERNOVAL|ATTR_KERNAMELS)) {
- /* must return negated buffer size or the error */
- if (context.count < 0)
- error = XFS_ERROR(ERANGE);
- else
- error = -context.count;
- } else
- ASSERT(error >= 0);
-
+ ASSERT(error >= 0);
return error;
}
ASSERT(! XFS_NOT_DQATTACHED(mp, dp));
xfs_ilock(dp, XFS_ILOCK_SHARED);
- if ((XFS_IFORK_Q(dp) == 0) ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- dp->i_d.di_anextents == 0)) {
+ if (!xfs_inode_hasattr(dp) ||
+ dp->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) {
xfs_iunlock(dp, XFS_ILOCK_SHARED);
- return(0);
+ return 0;
}
xfs_iunlock(dp, XFS_ILOCK_SHARED);
/*
* Decide on what work routines to call based on the inode size.
*/
- if ((XFS_IFORK_Q(dp) == 0) ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) ||
- (dp->i_d.di_aformat == XFS_DINODE_FMT_EXTENTS &&
- dp->i_d.di_anextents == 0)) {
+ if (!xfs_inode_hasattr(dp) ||
+ dp->i_d.di_aformat == XFS_DINODE_FMT_LOCAL) {
error = 0;
goto out;
}
xfs_da_brelse(args->trans, bp);
return(retval);
}
- args->rename = 1; /* an atomic rename */
+ args->op_flags |= XFS_DA_OP_RENAME; /* an atomic rename */
args->blkno2 = args->blkno; /* set 2nd entry info*/
args->index2 = args->index;
args->rmtblkno2 = args->rmtblkno;
* so that one disappears and one appears atomically. Then we
* must remove the "old" attribute/value pair.
*/
- if (args->rename) {
+ if (args->op_flags & XFS_DA_OP_RENAME) {
/*
* In a separate transaction, set the incomplete flag on the
* "old" attr and clear the incomplete flag on the "new" attr.
} else if (retval == EEXIST) {
if (args->flags & ATTR_CREATE)
goto out;
- args->rename = 1; /* atomic rename op */
+ args->op_flags |= XFS_DA_OP_RENAME; /* atomic rename op */
args->blkno2 = args->blkno; /* set 2nd entry info*/
args->index2 = args->index;
args->rmtblkno2 = args->rmtblkno;
* so that one disappears and one appears atomically. Then we
* must remove the "old" attribute/value pair.
*/
- if (args->rename) {
+ if (args->op_flags & XFS_DA_OP_RENAME) {
/*
* In a separate transaction, set the incomplete flag on the
* "old" attr and clear the incomplete flag on the "new" attr.
void
xfs_attr_trace_l_c(char *where, struct xfs_attr_list_context *context)
{
- xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_C, where,
- (__psunsigned_t)context->dp,
- (__psunsigned_t)context->cursor->hashval,
- (__psunsigned_t)context->cursor->blkno,
- (__psunsigned_t)context->cursor->offset,
- (__psunsigned_t)context->alist,
- (__psunsigned_t)context->bufsize,
- (__psunsigned_t)context->count,
- (__psunsigned_t)context->firstu,
- (__psunsigned_t)
- ((context->count > 0) &&
- !(context->flags & (ATTR_KERNAMELS|ATTR_KERNOVAL)))
- ? (ATTR_ENTRY(context->alist,
- context->count-1)->a_valuelen)
- : 0,
- (__psunsigned_t)context->dupcnt,
- (__psunsigned_t)context->flags,
+ xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_C, where, context,
(__psunsigned_t)NULL,
(__psunsigned_t)NULL,
(__psunsigned_t)NULL);
xfs_attr_trace_l_cn(char *where, struct xfs_attr_list_context *context,
struct xfs_da_intnode *node)
{
- xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CN, where,
- (__psunsigned_t)context->dp,
- (__psunsigned_t)context->cursor->hashval,
- (__psunsigned_t)context->cursor->blkno,
- (__psunsigned_t)context->cursor->offset,
- (__psunsigned_t)context->alist,
- (__psunsigned_t)context->bufsize,
- (__psunsigned_t)context->count,
- (__psunsigned_t)context->firstu,
- (__psunsigned_t)
- ((context->count > 0) &&
- !(context->flags & (ATTR_KERNAMELS|ATTR_KERNOVAL)))
- ? (ATTR_ENTRY(context->alist,
- context->count-1)->a_valuelen)
- : 0,
- (__psunsigned_t)context->dupcnt,
- (__psunsigned_t)context->flags,
+ xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CN, where, context,
(__psunsigned_t)be16_to_cpu(node->hdr.count),
(__psunsigned_t)be32_to_cpu(node->btree[0].hashval),
(__psunsigned_t)be32_to_cpu(node->btree[
xfs_attr_trace_l_cb(char *where, struct xfs_attr_list_context *context,
struct xfs_da_node_entry *btree)
{
- xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CB, where,
- (__psunsigned_t)context->dp,
- (__psunsigned_t)context->cursor->hashval,
- (__psunsigned_t)context->cursor->blkno,
- (__psunsigned_t)context->cursor->offset,
- (__psunsigned_t)context->alist,
- (__psunsigned_t)context->bufsize,
- (__psunsigned_t)context->count,
- (__psunsigned_t)context->firstu,
- (__psunsigned_t)
- ((context->count > 0) &&
- !(context->flags & (ATTR_KERNAMELS|ATTR_KERNOVAL)))
- ? (ATTR_ENTRY(context->alist,
- context->count-1)->a_valuelen)
- : 0,
- (__psunsigned_t)context->dupcnt,
- (__psunsigned_t)context->flags,
+ xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CB, where, context,
(__psunsigned_t)be32_to_cpu(btree->hashval),
(__psunsigned_t)be32_to_cpu(btree->before),
(__psunsigned_t)NULL);
xfs_attr_trace_l_cl(char *where, struct xfs_attr_list_context *context,
struct xfs_attr_leafblock *leaf)
{
- xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CL, where,
- (__psunsigned_t)context->dp,
- (__psunsigned_t)context->cursor->hashval,
- (__psunsigned_t)context->cursor->blkno,
- (__psunsigned_t)context->cursor->offset,
- (__psunsigned_t)context->alist,
- (__psunsigned_t)context->bufsize,
- (__psunsigned_t)context->count,
- (__psunsigned_t)context->firstu,
- (__psunsigned_t)
- ((context->count > 0) &&
- !(context->flags & (ATTR_KERNAMELS|ATTR_KERNOVAL)))
- ? (ATTR_ENTRY(context->alist,
- context->count-1)->a_valuelen)
- : 0,
- (__psunsigned_t)context->dupcnt,
- (__psunsigned_t)context->flags,
+ xfs_attr_trace_enter(XFS_ATTR_KTRACE_L_CL, where, context,
(__psunsigned_t)be16_to_cpu(leaf->hdr.count),
(__psunsigned_t)be32_to_cpu(leaf->entries[0].hashval),
(__psunsigned_t)be32_to_cpu(leaf->entries[
*/
void
xfs_attr_trace_enter(int type, char *where,
- __psunsigned_t a2, __psunsigned_t a3,
- __psunsigned_t a4, __psunsigned_t a5,
- __psunsigned_t a6, __psunsigned_t a7,
- __psunsigned_t a8, __psunsigned_t a9,
- __psunsigned_t a10, __psunsigned_t a11,
- __psunsigned_t a12, __psunsigned_t a13,
- __psunsigned_t a14, __psunsigned_t a15)
+ struct xfs_attr_list_context *context,
+ __psunsigned_t a13, __psunsigned_t a14,
+ __psunsigned_t a15)
{
ASSERT(xfs_attr_trace_buf);
ktrace_enter(xfs_attr_trace_buf, (void *)((__psunsigned_t)type),
- (void *)where,
- (void *)a2, (void *)a3, (void *)a4,
- (void *)a5, (void *)a6, (void *)a7,
- (void *)a8, (void *)a9, (void *)a10,
- (void *)a11, (void *)a12, (void *)a13,
- (void *)a14, (void *)a15);
+ (void *)((__psunsigned_t)where),
+ (void *)((__psunsigned_t)context->dp),
+ (void *)((__psunsigned_t)context->cursor->hashval),
+ (void *)((__psunsigned_t)context->cursor->blkno),
+ (void *)((__psunsigned_t)context->cursor->offset),
+ (void *)((__psunsigned_t)context->alist),
+ (void *)((__psunsigned_t)context->bufsize),
+ (void *)((__psunsigned_t)context->count),
+ (void *)((__psunsigned_t)context->firstu),
+ NULL,
+ (void *)((__psunsigned_t)context->dupcnt),
+ (void *)((__psunsigned_t)context->flags),
+ (void *)a13, (void *)a14, (void *)a15);
}
#endif /* XFS_ATTR_TRACE */
-
-
-/*========================================================================
- * System (pseudo) namespace attribute interface routines.
- *========================================================================*/
-
-STATIC int
-posix_acl_access_set(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- return xfs_acl_vset(vp, data, size, _ACL_TYPE_ACCESS);
-}
-
-STATIC int
-posix_acl_access_remove(
- bhv_vnode_t *vp, char *name, int xflags)
-{
- return xfs_acl_vremove(vp, _ACL_TYPE_ACCESS);
-}
-
-STATIC int
-posix_acl_access_get(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- return xfs_acl_vget(vp, data, size, _ACL_TYPE_ACCESS);
-}
-
-STATIC int
-posix_acl_access_exists(
- bhv_vnode_t *vp)
-{
- return xfs_acl_vhasacl_access(vp);
-}
-
-STATIC int
-posix_acl_default_set(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- return xfs_acl_vset(vp, data, size, _ACL_TYPE_DEFAULT);
-}
-
-STATIC int
-posix_acl_default_get(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- return xfs_acl_vget(vp, data, size, _ACL_TYPE_DEFAULT);
-}
-
-STATIC int
-posix_acl_default_remove(
- bhv_vnode_t *vp, char *name, int xflags)
-{
- return xfs_acl_vremove(vp, _ACL_TYPE_DEFAULT);
-}
-
-STATIC int
-posix_acl_default_exists(
- bhv_vnode_t *vp)
-{
- return xfs_acl_vhasacl_default(vp);
-}
-
-static struct attrnames posix_acl_access = {
- .attr_name = "posix_acl_access",
- .attr_namelen = sizeof("posix_acl_access") - 1,
- .attr_get = posix_acl_access_get,
- .attr_set = posix_acl_access_set,
- .attr_remove = posix_acl_access_remove,
- .attr_exists = posix_acl_access_exists,
-};
-
-static struct attrnames posix_acl_default = {
- .attr_name = "posix_acl_default",
- .attr_namelen = sizeof("posix_acl_default") - 1,
- .attr_get = posix_acl_default_get,
- .attr_set = posix_acl_default_set,
- .attr_remove = posix_acl_default_remove,
- .attr_exists = posix_acl_default_exists,
-};
-
-static struct attrnames *attr_system_names[] =
- { &posix_acl_access, &posix_acl_default };
-
-
-/*========================================================================
- * Namespace-prefix-style attribute name interface routines.
- *========================================================================*/
-
-STATIC int
-attr_generic_set(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- return -xfs_attr_set(xfs_vtoi(vp), name, data, size, xflags);
-}
-
-STATIC int
-attr_generic_get(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- int error, asize = size;
-
- error = xfs_attr_get(xfs_vtoi(vp), name, data, &asize, xflags);
- if (!error)
- return asize;
- return -error;
-}
-
-STATIC int
-attr_generic_remove(
- bhv_vnode_t *vp, char *name, int xflags)
-{
- return -xfs_attr_remove(xfs_vtoi(vp), name, xflags);
-}
-
-STATIC int
-attr_generic_listadd(
- attrnames_t *prefix,
- attrnames_t *namesp,
- void *data,
- size_t size,
- ssize_t *result)
-{
- char *p = data + *result;
-
- *result += prefix->attr_namelen;
- *result += namesp->attr_namelen + 1;
- if (!size)
- return 0;
- if (*result > size)
- return -ERANGE;
- strcpy(p, prefix->attr_name);
- p += prefix->attr_namelen;
- strcpy(p, namesp->attr_name);
- p += namesp->attr_namelen + 1;
- return 0;
-}
-
-STATIC int
-attr_system_list(
- bhv_vnode_t *vp,
- void *data,
- size_t size,
- ssize_t *result)
-{
- attrnames_t *namesp;
- int i, error = 0;
-
- for (i = 0; i < ATTR_SYSCOUNT; i++) {
- namesp = attr_system_names[i];
- if (!namesp->attr_exists || !namesp->attr_exists(vp))
- continue;
- error = attr_generic_listadd(&attr_system, namesp,
- data, size, result);
- if (error)
- break;
- }
- return error;
-}
-
-int
-attr_generic_list(
- bhv_vnode_t *vp, void *data, size_t size, int xflags, ssize_t *result)
-{
- attrlist_cursor_kern_t cursor = { 0 };
- int error;
-
- error = xfs_attr_list(xfs_vtoi(vp), data, size, xflags, &cursor);
- if (error > 0)
- return -error;
- *result = -error;
- return attr_system_list(vp, data, size, result);
-}
-
-attrnames_t *
-attr_lookup_namespace(
- char *name,
- struct attrnames **names,
- int nnames)
-{
- int i;
-
- for (i = 0; i < nnames; i++)
- if (!strncmp(name, names[i]->attr_name, names[i]->attr_namelen))
- return names[i];
- return NULL;
-}
-
-/*
- * Some checks to prevent people abusing EAs to get over quota:
- * - Don't allow modifying user EAs on devices/symlinks;
- * - Don't allow modifying user EAs if sticky bit set;
- */
-STATIC int
-attr_user_capable(
- bhv_vnode_t *vp,
- cred_t *cred)
-{
- struct inode *inode = vn_to_inode(vp);
-
- if (IS_IMMUTABLE(inode) || IS_APPEND(inode))
- return -EPERM;
- if (!S_ISREG(inode->i_mode) && !S_ISDIR(inode->i_mode) &&
- !capable(CAP_SYS_ADMIN))
- return -EPERM;
- if (S_ISDIR(inode->i_mode) && (inode->i_mode & S_ISVTX) &&
- (current_fsuid(cred) != inode->i_uid) && !capable(CAP_FOWNER))
- return -EPERM;
- return 0;
-}
-
-STATIC int
-attr_trusted_capable(
- bhv_vnode_t *vp,
- cred_t *cred)
-{
- struct inode *inode = vn_to_inode(vp);
-
- if (IS_IMMUTABLE(inode) || IS_APPEND(inode))
- return -EPERM;
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
- return 0;
-}
-
-STATIC int
-attr_system_set(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- attrnames_t *namesp;
- int error;
-
- if (xflags & ATTR_CREATE)
- return -EINVAL;
-
- namesp = attr_lookup_namespace(name, attr_system_names, ATTR_SYSCOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- error = namesp->attr_set(vp, name, data, size, xflags);
- if (!error)
- error = vn_revalidate(vp);
- return error;
-}
-
-STATIC int
-attr_system_get(
- bhv_vnode_t *vp, char *name, void *data, size_t size, int xflags)
-{
- attrnames_t *namesp;
-
- namesp = attr_lookup_namespace(name, attr_system_names, ATTR_SYSCOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- return namesp->attr_get(vp, name, data, size, xflags);
-}
-
-STATIC int
-attr_system_remove(
- bhv_vnode_t *vp, char *name, int xflags)
-{
- attrnames_t *namesp;
-
- namesp = attr_lookup_namespace(name, attr_system_names, ATTR_SYSCOUNT);
- if (!namesp)
- return -EOPNOTSUPP;
- return namesp->attr_remove(vp, name, xflags);
-}
-
-struct attrnames attr_system = {
- .attr_name = "system.",
- .attr_namelen = sizeof("system.") - 1,
- .attr_flag = ATTR_SYSTEM,
- .attr_get = attr_system_get,
- .attr_set = attr_system_set,
- .attr_remove = attr_system_remove,
- .attr_capable = (attrcapable_t)fs_noerr,
-};
-
-struct attrnames attr_trusted = {
- .attr_name = "trusted.",
- .attr_namelen = sizeof("trusted.") - 1,
- .attr_flag = ATTR_ROOT,
- .attr_get = attr_generic_get,
- .attr_set = attr_generic_set,
- .attr_remove = attr_generic_remove,
- .attr_capable = attr_trusted_capable,
-};
-
-struct attrnames attr_secure = {
- .attr_name = "security.",
- .attr_namelen = sizeof("security.") - 1,
- .attr_flag = ATTR_SECURE,
- .attr_get = attr_generic_get,
- .attr_set = attr_generic_set,
- .attr_remove = attr_generic_remove,
- .attr_capable = (attrcapable_t)fs_noerr,
-};
-
-struct attrnames attr_user = {
- .attr_name = "user.",
- .attr_namelen = sizeof("user.") - 1,
- .attr_get = attr_generic_get,
- .attr_set = attr_generic_set,
- .attr_remove = attr_generic_remove,
- .attr_capable = attr_user_capable,
-};
-
-struct attrnames *attr_namespaces[] =
- { &attr_system, &attr_trusted, &attr_secure, &attr_user };
#ifndef __XFS_ATTR_H__
#define __XFS_ATTR_H__
+struct xfs_inode;
+struct xfs_da_args;
+struct xfs_attr_list_context;
+
/*
- * xfs_attr.h
- *
* Large attribute lists are structured around Btrees where all the data
* elements are in the leaf nodes. Attribute names are hashed into an int,
* then that int is used as the index into the Btree. Since the hashval
* External interfaces
*========================================================================*/
-struct cred;
-struct xfs_attr_list_context;
-
-typedef int (*attrset_t)(bhv_vnode_t *, char *, void *, size_t, int);
-typedef int (*attrget_t)(bhv_vnode_t *, char *, void *, size_t, int);
-typedef int (*attrremove_t)(bhv_vnode_t *, char *, int);
-typedef int (*attrexists_t)(bhv_vnode_t *);
-typedef int (*attrcapable_t)(bhv_vnode_t *, struct cred *);
-
-typedef struct attrnames {
- char * attr_name;
- unsigned int attr_namelen;
- unsigned int attr_flag;
- attrget_t attr_get;
- attrset_t attr_set;
- attrremove_t attr_remove;
- attrexists_t attr_exists;
- attrcapable_t attr_capable;
-} attrnames_t;
-
-#define ATTR_NAMECOUNT 4
-extern struct attrnames attr_user;
-extern struct attrnames attr_secure;
-extern struct attrnames attr_system;
-extern struct attrnames attr_trusted;
-extern struct attrnames *attr_namespaces[ATTR_NAMECOUNT];
-
-extern attrnames_t *attr_lookup_namespace(char *, attrnames_t **, int);
-extern int attr_generic_list(bhv_vnode_t *, void *, size_t, int, ssize_t *);
#define ATTR_DONTFOLLOW 0x0001 /* -- unused, from IRIX -- */
#define ATTR_ROOT 0x0002 /* use attrs in root (trusted) namespace */
#define ATTR_SECURE 0x0008 /* use attrs in security namespace */
#define ATTR_CREATE 0x0010 /* pure create: fail if attr already exists */
#define ATTR_REPLACE 0x0020 /* pure set: fail if attr does not exist */
-#define ATTR_SYSTEM 0x0100 /* use attrs in system (pseudo) namespace */
-#define ATTR_KERNACCESS 0x0400 /* [kernel] iaccess, inode held io-locked */
#define ATTR_KERNOTIME 0x1000 /* [kernel] don't update inode timestamps */
#define ATTR_KERNOVAL 0x2000 /* [kernel] get attr size only, not value */
-#define ATTR_KERNAMELS 0x4000 /* [kernel] list attr names (simple list) */
-
-#define ATTR_KERNORMALS 0x0800 /* [kernel] normal attr list: user+secure */
-#define ATTR_KERNROOTLS 0x8000 /* [kernel] include root in the attr list */
-#define ATTR_KERNFULLS (ATTR_KERNORMALS|ATTR_KERNROOTLS)
/*
* The maximum size (into the kernel or returned from the kernel) of an
((attrlist_ent_t *) \
&((char *)buffer)[ ((attrlist_t *)(buffer))->al_offset[index] ])
-/*
- * Multi-attribute operation vector.
- */
-typedef struct attr_multiop {
- int am_opcode; /* operation to perform (ATTR_OP_GET, etc.) */
- int am_error; /* [out arg] result of this sub-op (an errno) */
- char *am_attrname; /* attribute name to work with */
- char *am_attrvalue; /* [in/out arg] attribute value (raw bytes) */
- int am_length; /* [in/out arg] length of value */
- int am_flags; /* bitwise OR of attr API flags defined above */
-} attr_multiop_t;
-
-#define ATTR_OP_GET 1 /* return the indicated attr's value */
-#define ATTR_OP_SET 2 /* set/create the indicated attr/value pair */
-#define ATTR_OP_REMOVE 3 /* remove the indicated attr */
-
/*
* Kernel-internal version of the attrlist cursor.
*/
/*========================================================================
- * Function prototypes for the kernel.
+ * Structure used to pass context around among the routines.
*========================================================================*/
-struct xfs_inode;
-struct attrlist_cursor_kern;
-struct xfs_da_args;
+
+typedef int (*put_listent_func_t)(struct xfs_attr_list_context *, int,
+ char *, int, int, char *);
+
+typedef struct xfs_attr_list_context {
+ struct xfs_inode *dp; /* inode */
+ struct attrlist_cursor_kern *cursor; /* position in list */
+ char *alist; /* output buffer */
+ int seen_enough; /* T/F: seen enough of list? */
+ ssize_t count; /* num used entries */
+ int dupcnt; /* count dup hashvals seen */
+ int bufsize; /* total buffer size */
+ int firstu; /* first used byte in buffer */
+ int flags; /* from VOP call */
+ int resynch; /* T/F: resynch with cursor */
+ int put_value; /* T/F: need value for listent */
+ put_listent_func_t put_listent; /* list output fmt function */
+ int index; /* index into output buffer */
+} xfs_attr_list_context_t;
+
+
+/*========================================================================
+ * Function prototypes for the kernel.
+ *========================================================================*/
/*
* Overall external interface routines.
*/
int xfs_attr_inactive(struct xfs_inode *dp);
-
-int xfs_attr_shortform_getvalue(struct xfs_da_args *);
int xfs_attr_fetch(struct xfs_inode *, struct xfs_name *, char *, int *, int);
int xfs_attr_rmtval_get(struct xfs_da_args *args);
+int xfs_attr_list_int(struct xfs_attr_list_context *);
#endif /* __XFS_ATTR_H__ */
* Namespace helper routines
*========================================================================*/
-STATIC_INLINE attrnames_t *
-xfs_attr_flags_namesp(int flags)
-{
- return ((flags & XFS_ATTR_SECURE) ? &attr_secure:
- ((flags & XFS_ATTR_ROOT) ? &attr_trusted : &attr_user));
-}
-
/*
* If namespace bits don't match return 0.
* If all match then return 1.
return XFS_ATTR_NSP_ONDISK(ondisk_flags) == XFS_ATTR_NSP_ARGS_TO_ONDISK(arg_flags);
}
-/*
- * If namespace bits don't match and we don't have an override for it
- * then return 0.
- * If all match or are overridable then return 1.
- */
-STATIC_INLINE int
-xfs_attr_namesp_match_overrides(int arg_flags, int ondisk_flags)
-{
- if (((arg_flags & ATTR_SECURE) == 0) !=
- ((ondisk_flags & XFS_ATTR_SECURE) == 0) &&
- !(arg_flags & ATTR_KERNORMALS))
- return 0;
- if (((arg_flags & ATTR_ROOT) == 0) !=
- ((ondisk_flags & XFS_ATTR_ROOT) == 0) &&
- !(arg_flags & ATTR_KERNROOTLS))
- return 0;
- return 1;
-}
-
/*========================================================================
* External routines when attribute fork size < XFS_LITINO(mp).
* Fix up the start offset of the attribute fork
*/
totsize -= size;
- if (totsize == sizeof(xfs_attr_sf_hdr_t) && !args->addname &&
- (mp->m_flags & XFS_MOUNT_ATTR2) &&
- (dp->i_d.di_format != XFS_DINODE_FMT_BTREE)) {
+ if (totsize == sizeof(xfs_attr_sf_hdr_t) &&
+ !(args->op_flags & XFS_DA_OP_ADDNAME) &&
+ (mp->m_flags & XFS_MOUNT_ATTR2) &&
+ (dp->i_d.di_format != XFS_DINODE_FMT_BTREE)) {
/*
* Last attribute now removed, revert to original
* inode format making all literal area available
xfs_idata_realloc(dp, -size, XFS_ATTR_FORK);
dp->i_d.di_forkoff = xfs_attr_shortform_bytesfit(dp, totsize);
ASSERT(dp->i_d.di_forkoff);
- ASSERT(totsize > sizeof(xfs_attr_sf_hdr_t) || args->addname ||
- !(mp->m_flags & XFS_MOUNT_ATTR2) ||
- dp->i_d.di_format == XFS_DINODE_FMT_BTREE);
+ ASSERT(totsize > sizeof(xfs_attr_sf_hdr_t) ||
+ (args->op_flags & XFS_DA_OP_ADDNAME) ||
+ !(mp->m_flags & XFS_MOUNT_ATTR2) ||
+ dp->i_d.di_format == XFS_DINODE_FMT_BTREE);
dp->i_afp->if_ext_max =
XFS_IFORK_ASIZE(dp) / (uint)sizeof(xfs_bmbt_rec_t);
dp->i_df.if_ext_max =
nargs.total = args->total;
nargs.whichfork = XFS_ATTR_FORK;
nargs.trans = args->trans;
- nargs.oknoent = 1;
+ nargs.op_flags = XFS_DA_OP_OKNOENT;
sfe = &sf->list[0];
for (i = 0; i < sf->hdr.count; i++) {
out:
if(bp)
xfs_da_buf_done(bp);
- kmem_free(tmpbuffer, size);
+ kmem_free(tmpbuffer);
return(error);
}
(XFS_ISRESET_CURSOR(cursor) &&
(dp->i_afp->if_bytes + sf->hdr.count * 16) < context->bufsize)) {
for (i = 0, sfe = &sf->list[0]; i < sf->hdr.count; i++) {
- attrnames_t *namesp;
-
- if (!xfs_attr_namesp_match_overrides(context->flags, sfe->flags)) {
- sfe = XFS_ATTR_SF_NEXTENTRY(sfe);
- continue;
- }
- namesp = xfs_attr_flags_namesp(sfe->flags);
error = context->put_listent(context,
- namesp,
+ sfe->flags,
(char *)sfe->nameval,
(int)sfe->namelen,
(int)sfe->valuelen,
XFS_ERRLEVEL_LOW,
context->dp->i_mount, sfe);
xfs_attr_trace_l_c("sf corrupted", context);
- kmem_free(sbuf, sbsize);
+ kmem_free(sbuf);
return XFS_ERROR(EFSCORRUPTED);
}
- if (!xfs_attr_namesp_match_overrides(context->flags, sfe->flags)) {
- sfe = XFS_ATTR_SF_NEXTENTRY(sfe);
- continue;
- }
+
sbp->entno = i;
sbp->hash = xfs_da_hashname((char *)sfe->nameval, sfe->namelen);
sbp->name = (char *)sfe->nameval;
}
}
if (i == nsbuf) {
- kmem_free(sbuf, sbsize);
+ kmem_free(sbuf);
xfs_attr_trace_l_c("blk end", context);
return(0);
}
* Loop putting entries into the user buffer.
*/
for ( ; i < nsbuf; i++, sbp++) {
- attrnames_t *namesp;
-
- namesp = xfs_attr_flags_namesp(sbp->flags);
-
if (cursor->hashval != sbp->hash) {
cursor->hashval = sbp->hash;
cursor->offset = 0;
}
error = context->put_listent(context,
- namesp,
+ sbp->flags,
sbp->name,
sbp->namelen,
sbp->valuelen,
cursor->offset++;
}
- kmem_free(sbuf, sbsize);
+ kmem_free(sbuf);
xfs_attr_trace_l_c("sf E-O-F", context);
return(0);
}
nargs.total = args->total;
nargs.whichfork = XFS_ATTR_FORK;
nargs.trans = args->trans;
- nargs.oknoent = 1;
+ nargs.op_flags = XFS_DA_OP_OKNOENT;
entry = &leaf->entries[0];
for (i = 0; i < be16_to_cpu(leaf->hdr.count); entry++, i++) {
if (entry->flags & XFS_ATTR_INCOMPLETE)
error = 0;
out:
- kmem_free(tmpbuffer, XFS_LBSIZE(dp->i_mount));
+ kmem_free(tmpbuffer);
return(error);
}
entry->hashval = cpu_to_be32(args->hashval);
entry->flags = tmp ? XFS_ATTR_LOCAL : 0;
entry->flags |= XFS_ATTR_NSP_ARGS_TO_ONDISK(args->flags);
- if (args->rename) {
+ if (args->op_flags & XFS_DA_OP_RENAME) {
entry->flags |= XFS_ATTR_INCOMPLETE;
if ((args->blkno2 == args->blkno) &&
(args->index2 <= args->index)) {
be16_to_cpu(hdr_s->count), mp);
xfs_da_log_buf(trans, bp, 0, XFS_LBSIZE(mp) - 1);
- kmem_free(tmpbuffer, XFS_LBSIZE(mp));
+ kmem_free(tmpbuffer);
}
/*
be16_to_cpu(drop_hdr->count), mp);
}
memcpy((char *)save_leaf, (char *)tmp_leaf, state->blocksize);
- kmem_free(tmpbuffer, state->blocksize);
+ kmem_free(tmpbuffer);
}
xfs_da_log_buf(state->args->trans, save_blk->bp, 0,
*/
retval = 0;
for ( ; (i < be16_to_cpu(leaf->hdr.count)); entry++, i++) {
- attrnames_t *namesp;
-
if (be32_to_cpu(entry->hashval) != cursor->hashval) {
cursor->hashval = be32_to_cpu(entry->hashval);
cursor->offset = 0;
if (entry->flags & XFS_ATTR_INCOMPLETE)
continue; /* skip incomplete entries */
- if (!xfs_attr_namesp_match_overrides(context->flags, entry->flags))
- continue;
-
- namesp = xfs_attr_flags_namesp(entry->flags);
if (entry->flags & XFS_ATTR_LOCAL) {
xfs_attr_leaf_name_local_t *name_loc =
XFS_ATTR_LEAF_NAME_LOCAL(leaf, i);
retval = context->put_listent(context,
- namesp,
+ entry->flags,
(char *)name_loc->nameval,
(int)name_loc->namelen,
be16_to_cpu(name_loc->valuelen),
if (retval)
return retval;
retval = context->put_listent(context,
- namesp,
+ entry->flags,
(char *)name_rmt->name,
(int)name_rmt->namelen,
valuelen,
(char*)args.value);
- kmem_free(args.value, valuelen);
- }
- else {
+ kmem_free(args.value);
+ } else {
retval = context->put_listent(context,
- namesp,
+ entry->flags,
(char *)name_rmt->name,
(int)name_rmt->namelen,
valuelen,
error = tmp; /* save only the 1st errno */
}
- kmem_free((xfs_caddr_t)list, size);
+ kmem_free((xfs_caddr_t)list);
return(error);
}
struct attrlist;
struct attrlist_cursor_kern;
-struct attrnames;
+struct xfs_attr_list_context;
struct xfs_dabuf;
struct xfs_da_args;
struct xfs_da_state;
return (((bsize) >> 1) + ((bsize) >> 2));
}
-
-/*========================================================================
- * Structure used to pass context around among the routines.
- *========================================================================*/
-
-
-struct xfs_attr_list_context;
-
-typedef int (*put_listent_func_t)(struct xfs_attr_list_context *, struct attrnames *,
- char *, int, int, char *);
-
-typedef struct xfs_attr_list_context {
- struct xfs_inode *dp; /* inode */
- struct attrlist_cursor_kern *cursor; /* position in list */
- struct attrlist *alist; /* output buffer */
- int seen_enough; /* T/F: seen enough of list? */
- int count; /* num used entries */
- int dupcnt; /* count dup hashvals seen */
- int bufsize; /* total buffer size */
- int firstu; /* first used byte in buffer */
- int flags; /* from VOP call */
- int resynch; /* T/F: resynch with cursor */
- int put_value; /* T/F: need value for listent */
- put_listent_func_t put_listent; /* list output fmt function */
- int index; /* index into output buffer */
-} xfs_attr_list_context_t;
-
/*
* Used to keep a list of "remote value" extents when unlinking an inode.
*/
void xfs_attr_trace_l_cl(char *where, struct xfs_attr_list_context *context,
struct xfs_attr_leafblock *leaf);
void xfs_attr_trace_enter(int type, char *where,
- __psunsigned_t a2, __psunsigned_t a3,
- __psunsigned_t a4, __psunsigned_t a5,
- __psunsigned_t a6, __psunsigned_t a7,
- __psunsigned_t a8, __psunsigned_t a9,
- __psunsigned_t a10, __psunsigned_t a11,
- __psunsigned_t a12, __psunsigned_t a13,
- __psunsigned_t a14, __psunsigned_t a15);
+ struct xfs_attr_list_context *context,
+ __psunsigned_t a13, __psunsigned_t a14,
+ __psunsigned_t a15);
#else
#define xfs_attr_trace_l_c(w,c)
#define xfs_attr_trace_l_cn(w,c,n)
cur->bc_private.b.firstblock = *firstblock;
if ((error = xfs_bmbt_lookup_ge(cur, 0, 0, 0, &stat)))
goto error0;
- ASSERT(stat == 1); /* must be at least one entry */
+ /* must be at least one entry */
+ XFS_WANT_CORRUPTED_GOTO(stat == 1, error0);
if ((error = xfs_bmbt_newroot(cur, flags, &stat)))
goto error0;
if (stat == 0) {
RIGHT.br_startblock,
RIGHT.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, LEFT.br_startoff,
LEFT.br_startblock,
LEFT.br_blockcount +
LEFT.br_startblock, LEFT.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, LEFT.br_startoff,
LEFT.br_startblock,
LEFT.br_blockcount +
RIGHT.br_startblock,
RIGHT.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, PREV.br_startoff,
new->br_startblock,
PREV.br_blockcount +
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = XFS_EXT_NORM;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
*dnew = 0;
/* DELTA: The in-core extent described by new changed type. */
LEFT.br_startblock, LEFT.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, LEFT.br_startoff,
LEFT.br_startblock,
LEFT.br_blockcount +
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = XFS_EXT_NORM;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
if (ip->i_d.di_format == XFS_DINODE_FMT_EXTENTS &&
ip->i_d.di_nextents > ip->i_df.if_ext_max) {
RIGHT.br_startblock,
RIGHT.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, new->br_startoff,
new->br_startblock,
new->br_blockcount +
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = XFS_EXT_NORM;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
if (ip->i_d.di_format == XFS_DINODE_FMT_EXTENTS &&
ip->i_d.di_nextents > ip->i_df.if_ext_max) {
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = XFS_EXT_NORM;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
if (ip->i_d.di_format == XFS_DINODE_FMT_EXTENTS &&
ip->i_d.di_nextents > ip->i_df.if_ext_max) {
RIGHT.br_startblock,
RIGHT.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, LEFT.br_startoff,
LEFT.br_startblock,
LEFT.br_blockcount + PREV.br_blockcount +
PREV.br_startblock, PREV.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, LEFT.br_startoff,
LEFT.br_startblock,
LEFT.br_blockcount + PREV.br_blockcount,
RIGHT.br_startblock,
RIGHT.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, new->br_startoff,
new->br_startblock,
new->br_blockcount + RIGHT.br_blockcount,
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, new->br_startoff,
new->br_startblock, new->br_blockcount,
newext)))
PREV.br_startblock, PREV.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur,
PREV.br_startoff + new->br_blockcount,
PREV.br_startblock + new->br_blockcount,
PREV.br_startblock, PREV.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur,
PREV.br_startoff + new->br_blockcount,
PREV.br_startblock + new->br_blockcount,
cur->bc_rec.b = *new;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
/* DELTA: One in-core extent is split in two. */
temp = PREV.br_startoff;
PREV.br_startblock,
PREV.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, PREV.br_startoff,
PREV.br_startblock,
PREV.br_blockcount - new->br_blockcount,
PREV.br_startblock, PREV.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, PREV.br_startoff,
PREV.br_startblock,
PREV.br_blockcount - new->br_blockcount,
new->br_startblock, new->br_blockcount,
&i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = XFS_EXT_NORM;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
/* DELTA: One in-core extent is split in two. */
temp = PREV.br_startoff;
PREV.br_startblock, PREV.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
/* new right extent - oldext */
if ((error = xfs_bmbt_update(cur, r[1].br_startoff,
r[1].br_startblock, r[1].br_blockcount,
r[1].br_state)))
goto done;
/* new left extent - oldext */
- PREV.br_blockcount =
- new->br_startoff - PREV.br_startoff;
cur->bc_rec.b = PREV;
+ cur->bc_rec.b.br_blockcount =
+ new->br_startoff - PREV.br_startoff;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
- if ((error = xfs_bmbt_increment(cur, 0, &i)))
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
+ /*
+ * Reset the cursor to the position of the new extent
+ * we are about to insert as we can't trust it after
+ * the previous insert.
+ */
+ if ((error = xfs_bmbt_lookup_eq(cur, new->br_startoff,
+ new->br_startblock, new->br_blockcount,
+ &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
/* new middle extent - newext */
- cur->bc_rec.b = *new;
+ cur->bc_rec.b.br_state = new->br_state;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
/* DELTA: One in-core extent is split in three. */
temp = PREV.br_startoff;
right.br_startblock,
right.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_decrement(cur, 0, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, left.br_startoff,
left.br_startblock,
left.br_blockcount +
left.br_startblock,
left.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, left.br_startoff,
left.br_startblock,
left.br_blockcount +
right.br_startblock,
right.br_blockcount, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
if ((error = xfs_bmbt_update(cur, new->br_startoff,
new->br_startblock,
new->br_blockcount +
new->br_startblock,
new->br_blockcount, &i)))
goto done;
- ASSERT(i == 0);
+ XFS_WANT_CORRUPTED_GOTO(i == 0, done);
cur->bc_rec.b.br_state = new->br_state;
if ((error = xfs_bmbt_insert(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
/* DELTA: A new extent was added in a hole. */
temp = new->br_startoff;
got.br_startblock, got.br_blockcount,
&i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
}
da_old = da_new = 0;
} else {
}
if ((error = xfs_bmbt_delete(cur, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
break;
case 2:
got.br_startblock,
temp, &i)))
goto done;
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
/*
* Update the btree record back
* to the original value.
error = XFS_ERROR(ENOSPC);
goto done;
}
- ASSERT(i == 1);
+ XFS_WANT_CORRUPTED_GOTO(i == 1, done);
} else
flags |= XFS_ILOG_FEXT(whichfork);
XFS_IFORK_NEXT_SET(ip, whichfork,
xfs_iunlock_map_shared(ip, lock);
xfs_iunlock(ip, XFS_IOLOCK_SHARED);
- kmem_free(map, subnex * sizeof(*map));
+ kmem_free(map);
return error;
}
/*
* Header for free extent list.
+ *
+ * xbf_low is used by the allocator to activate the lowspace algorithm -
+ * when free space is running low the extent allocator may choose to
+ * allocate an extent from an AG without leaving sufficient space for
+ * a btree split when inserting the new extent. In this case the allocator
+ * will enable the lowspace algorithm which is supposed to allow further
+ * allocations (such as btree splits and newroots) to allocate from
+ * sequential AGs. In order to avoid locking AGs out of order the lowspace
+ * algorithm will start searching for free space from AG 0. If the correct
+ * transaction reservations have been made then this algorithm will eventually
+ * find all the space it needs.
*/
typedef struct xfs_bmap_free
{
xfs_bmap_free_item_t *xbf_first; /* list of to-be-free extents */
int xbf_count; /* count of items on list */
- int xbf_low; /* kludge: alloc in low mode */
+ int xbf_low; /* alloc in low mode */
} xfs_bmap_free_t;
#define XFS_BMAP_MAX_NMAP 4
left = XFS_BUF_TO_BMBT_BLOCK(lbp);
args.fsbno = cur->bc_private.b.firstblock;
args.firstblock = args.fsbno;
+ args.minleft = 0;
if (args.fsbno == NULLFSBLOCK) {
args.fsbno = lbno;
args.type = XFS_ALLOCTYPE_START_BNO;
- } else
+ /*
+ * Make sure there is sufficient room left in the AG to
+ * complete a full tree split for an extent insert. If
+ * we are converting the middle part of an extent then
+ * we may need space for two tree splits.
+ *
+ * We are relying on the caller to make the correct block
+ * reservation for this operation to succeed. If the
+ * reservation amount is insufficient then we may fail a
+ * block allocation here and corrupt the filesystem.
+ */
+ args.minleft = xfs_trans_get_block_res(args.tp);
+ } else if (cur->bc_private.b.flist->xbf_low)
+ args.type = XFS_ALLOCTYPE_START_BNO;
+ else
args.type = XFS_ALLOCTYPE_NEAR_BNO;
- args.mod = args.minleft = args.alignment = args.total = args.isfl =
+ args.mod = args.alignment = args.total = args.isfl =
args.userdata = args.minalignslop = 0;
args.minlen = args.maxlen = args.prod = 1;
args.wasdel = cur->bc_private.b.flags & XFS_BTCUR_BPRV_WASDEL;
XFS_BMBT_TRACE_CURSOR(cur, ERROR);
return error;
}
+ if (args.fsbno == NULLFSBLOCK && args.minleft) {
+ /*
+ * Could not find an AG with enough free space to satisfy
+ * a full btree split. Try again without minleft and if
+ * successful activate the lowspace algorithm.
+ */
+ args.fsbno = 0;
+ args.type = XFS_ALLOCTYPE_FIRST_AG;
+ args.minleft = 0;
+ if ((error = xfs_alloc_vextent(&args))) {
+ XFS_BMBT_TRACE_CURSOR(cur, ERROR);
+ return error;
+ }
+ cur->bc_private.b.flist->xbf_low = 1;
+ }
if (args.fsbno == NULLFSBLOCK) {
XFS_BMBT_TRACE_CURSOR(cur, EXIT);
*stat = 0;
* Insert the current record at the point referenced by cur.
*
* A multi-level split of the tree on insert will invalidate the original
- * cursor. It appears, however, that some callers assume that the cursor is
- * always valid. Hence if we do a multi-level split we need to revalidate the
- * cursor.
- *
- * When a split occurs, we will see a new cursor returned. Use that as a
- * trigger to determine if we need to revalidate the original cursor. If we get
- * a split, then use the original irec to lookup up the path of the record we
- * just inserted.
- *
- * Note that the fact that the btree root is in the inode means that we can
- * have the level of the tree change without a "split" occurring at the root
- * level. What happens is that the root is migrated to an allocated block and
- * the inode root is pointed to it. This means a single split can change the
- * level of the tree (level 2 -> level 3) and invalidate the old cursor. Hence
- * the level change should be accounted as a split so as to correctly trigger a
- * revalidation of the old cursor.
+ * cursor. All callers of this function should assume that the cursor is
+ * no longer valid and revalidate it.
*/
int /* error */
xfs_bmbt_insert(
xfs_fsblock_t nbno;
xfs_btree_cur_t *ncur;
xfs_bmbt_rec_t nrec;
- xfs_bmbt_irec_t oirec; /* original irec */
xfs_btree_cur_t *pcur;
- int splits = 0;
XFS_BMBT_TRACE_CURSOR(cur, ENTRY);
level = 0;
nbno = NULLFSBLOCK;
- oirec = cur->bc_rec.b;
xfs_bmbt_disk_set_all(&nrec, &cur->bc_rec.b);
ncur = NULL;
pcur = cur;
&i))) {
if (pcur != cur)
xfs_btree_del_cursor(pcur, XFS_BTREE_ERROR);
- goto error0;
+ XFS_BMBT_TRACE_CURSOR(cur, ERROR);
+ return error;
}
XFS_WANT_CORRUPTED_GOTO(i == 1, error0);
if (pcur != cur && (ncur || nbno == NULLFSBLOCK)) {
- /* allocating a new root is effectively a split */
- if (cur->bc_nlevels != pcur->bc_nlevels)
- splits++;
cur->bc_nlevels = pcur->bc_nlevels;
cur->bc_private.b.allocated +=
pcur->bc_private.b.allocated;
xfs_btree_del_cursor(pcur, XFS_BTREE_NOERROR);
}
if (ncur) {
- splits++;
pcur = ncur;
ncur = NULL;
}
} while (nbno != NULLFSBLOCK);
-
- if (splits > 1) {
- /* revalidate the old cursor as we had a multi-level split */
- error = xfs_bmbt_lookup_eq(cur, oirec.br_startoff,
- oirec.br_startblock, oirec.br_blockcount, &i);
- if (error)
- goto error0;
- ASSERT(i == 1);
- }
-
XFS_BMBT_TRACE_CURSOR(cur, EXIT);
*stat = i;
return 0;
#endif
args.fsbno = be64_to_cpu(*pp);
args.type = XFS_ALLOCTYPE_START_BNO;
- } else
+ } else if (cur->bc_private.b.flist->xbf_low)
+ args.type = XFS_ALLOCTYPE_START_BNO;
+ else
args.type = XFS_ALLOCTYPE_NEAR_BNO;
if ((error = xfs_alloc_vextent(&args))) {
XFS_BMBT_TRACE_CURSOR(cur, ERROR);
}
#ifdef XFS_TRANS_DEBUG
- kmem_free(bip->bli_orig, XFS_BUF_COUNT(bp));
+ kmem_free(bip->bli_orig);
bip->bli_orig = NULL;
- kmem_free(bip->bli_logged, XFS_BUF_COUNT(bp) / NBBY);
+ kmem_free(bip->bli_logged);
bip->bli_logged = NULL;
#endif /* XFS_TRANS_DEBUG */
xfs_trans_delete_ail(mp, (xfs_log_item_t *)bip);
#ifdef XFS_TRANS_DEBUG
- kmem_free(bip->bli_orig, XFS_BUF_COUNT(bp));
+ kmem_free(bip->bli_orig);
bip->bli_orig = NULL;
- kmem_free(bip->bli_logged, XFS_BUF_COUNT(bp) / NBBY);
+ kmem_free(bip->bli_logged);
bip->bli_logged = NULL;
#endif /* XFS_TRANS_DEBUG */
#define XFSMNT_IOSIZE 0x00002000 /* optimize for I/O size */
#define XFSMNT_OSYNCISOSYNC 0x00004000 /* o_sync is REALLY o_sync */
/* (osyncisdsync is default) */
+#define XFSMNT_NOATTR2 0x00008000 /* turn off ATTR2 EA format */
#define XFSMNT_32BITINODES 0x00200000 /* restrict inodes to 32
* bits of address space */
#define XFSMNT_GQUOTA 0x00400000 /* group quota accounting */
}
if (level < 0) {
*result = XFS_ERROR(ENOENT); /* we're out of our tree */
- ASSERT(args->oknoent);
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
return(0);
}
}
}
+enum xfs_dacmp
+xfs_da_compname(
+ struct xfs_da_args *args,
+ const char *name,
+ int len)
+{
+ return (args->namelen == len && memcmp(args->name, name, len) == 0) ?
+ XFS_CMP_EXACT : XFS_CMP_DIFFERENT;
+}
+
+static xfs_dahash_t
+xfs_default_hashname(
+ struct xfs_name *name)
+{
+ return xfs_da_hashname(name->name, name->len);
+}
+
+const struct xfs_nameops xfs_default_nameops = {
+ .hashname = xfs_default_hashname,
+ .compname = xfs_da_compname
+};
+
/*
* Add a block to the btree ahead of the file.
* Return the new block number to the caller.
args->firstblock, args->total,
&mapp[mapi], &nmap, args->flist,
NULL))) {
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
return error;
}
if (nmap < 1)
mapp[mapi - 1].br_startoff + mapp[mapi - 1].br_blockcount !=
bno + count) {
if (mapp != &map)
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
return XFS_ERROR(ENOSPC);
}
if (mapp != &map)
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
*new_blkno = (xfs_dablk_t)bno;
return 0;
}
}
}
if (bplist) {
- kmem_free(bplist, sizeof(*bplist) * nmap);
+ kmem_free(bplist);
}
if (mapp != &map) {
- kmem_free(mapp, sizeof(*mapp) * nfsb);
+ kmem_free(mapp);
}
if (bpp)
*bpp = rbp;
if (bplist) {
for (i = 0; i < nbplist; i++)
xfs_trans_brelse(trans, bplist[i]);
- kmem_free(bplist, sizeof(*bplist) * nmap);
+ kmem_free(bplist);
}
exit0:
if (mapp != &map)
- kmem_free(mapp, sizeof(*mapp) * nfsb);
+ kmem_free(mapp);
if (bpp)
*bpp = NULL;
return error;
#ifdef XFS_DABUF_DEBUG
xfs_dabuf_t *xfs_dabuf_global_list;
-spinlock_t xfs_dabuf_global_lock;
+static DEFINE_SPINLOCK(xfs_dabuf_global_lock);
#endif
/*
if (dabuf->dirty)
xfs_da_buf_clean(dabuf);
if (dabuf->nbuf > 1)
- kmem_free(dabuf->data, BBTOB(dabuf->bbcount));
+ kmem_free(dabuf->data);
#ifdef XFS_DABUF_DEBUG
{
spin_lock(&xfs_dabuf_global_lock);
if (dabuf->nbuf == 1)
kmem_zone_free(xfs_dabuf_zone, dabuf);
else
- kmem_free(dabuf, XFS_DA_BUF_SIZE(dabuf->nbuf));
+ kmem_free(dabuf);
}
/*
for (i = 0; i < nbuf; i++)
xfs_trans_brelse(tp, bplist[i]);
if (bplist != &bp)
- kmem_free(bplist, nbuf * sizeof(*bplist));
+ kmem_free(bplist);
}
/*
for (i = 0; i < nbuf; i++)
xfs_trans_binval(tp, bplist[i]);
if (bplist != &bp)
- kmem_free(bplist, nbuf * sizeof(*bplist));
+ kmem_free(bplist);
}
/*
* Btree searching and modification structure definitions.
*========================================================================*/
+/*
+ * Search comparison results
+ */
+enum xfs_dacmp {
+ XFS_CMP_DIFFERENT, /* names are completely different */
+ XFS_CMP_EXACT, /* names are exactly the same */
+ XFS_CMP_CASE /* names are same but differ in case */
+};
+
/*
* Structure to ease passing around component names.
*/
int index2; /* index of 2nd attr in blk */
xfs_dablk_t rmtblkno2; /* remote attr value starting blkno */
int rmtblkcnt2; /* remote attr value block count */
- unsigned char justcheck; /* T/F: check for ok with no space */
- unsigned char rename; /* T/F: this is an atomic rename op */
- unsigned char addname; /* T/F: this is an add operation */
- unsigned char oknoent; /* T/F: ok to return ENOENT, else die */
+ int op_flags; /* operation flags */
+ enum xfs_dacmp cmpresult; /* name compare result for lookups */
} xfs_da_args_t;
+/*
+ * Operation flags:
+ */
+#define XFS_DA_OP_JUSTCHECK 0x0001 /* check for ok with no space */
+#define XFS_DA_OP_RENAME 0x0002 /* this is an atomic rename op */
+#define XFS_DA_OP_ADDNAME 0x0004 /* this is an add operation */
+#define XFS_DA_OP_OKNOENT 0x0008 /* lookup/add op, ENOENT ok, else die */
+#define XFS_DA_OP_CILOOKUP 0x0010 /* lookup to return CI name if found */
+
/*
* Structure to describe buffer(s) for a block.
* This is needed in the directory version 2 format case, when
(uint)(XFS_DA_LOGOFF(BASE, ADDR)), \
(uint)(XFS_DA_LOGOFF(BASE, ADDR)+(SIZE)-1)
+/*
+ * Name ops for directory and/or attr name operations
+ */
+struct xfs_nameops {
+ xfs_dahash_t (*hashname)(struct xfs_name *);
+ enum xfs_dacmp (*compname)(struct xfs_da_args *, const char *, int);
+};
+
#ifdef __KERNEL__
/*========================================================================
xfs_dabuf_t *dead_buf);
uint xfs_da_hashname(const uchar_t *name_string, int name_length);
+enum xfs_dacmp xfs_da_compname(struct xfs_da_args *args,
+ const char *name, int len);
+
+
xfs_da_state_t *xfs_da_state_alloc(void);
void xfs_da_state_free(xfs_da_state_t *state);
out_put_file:
fput(file);
out_free_sxp:
- kmem_free(sxp, sizeof(xfs_swapext_t));
+ kmem_free(sxp);
out:
return error;
}
xfs_iunlock(tip, lock_flags);
}
if (tempifp != NULL)
- kmem_free(tempifp, sizeof(xfs_ifork_t));
+ kmem_free(tempifp);
return error;
}
struct xfs_name xfs_name_dotdot = {"..", 2};
+extern const struct xfs_nameops xfs_default_nameops;
+
+/*
+ * ASCII case-insensitive (ie. A-Z) support for directories that was
+ * used in IRIX.
+ */
+STATIC xfs_dahash_t
+xfs_ascii_ci_hashname(
+ struct xfs_name *name)
+{
+ xfs_dahash_t hash;
+ int i;
+
+ for (i = 0, hash = 0; i < name->len; i++)
+ hash = tolower(name->name[i]) ^ rol32(hash, 7);
+
+ return hash;
+}
+
+STATIC enum xfs_dacmp
+xfs_ascii_ci_compname(
+ struct xfs_da_args *args,
+ const char *name,
+ int len)
+{
+ enum xfs_dacmp result;
+ int i;
+
+ if (args->namelen != len)
+ return XFS_CMP_DIFFERENT;
+
+ result = XFS_CMP_EXACT;
+ for (i = 0; i < len; i++) {
+ if (args->name[i] == name[i])
+ continue;
+ if (tolower(args->name[i]) != tolower(name[i]))
+ return XFS_CMP_DIFFERENT;
+ result = XFS_CMP_CASE;
+ }
+
+ return result;
+}
+
+static struct xfs_nameops xfs_ascii_ci_nameops = {
+ .hashname = xfs_ascii_ci_hashname,
+ .compname = xfs_ascii_ci_compname,
+};
+
void
xfs_dir_mount(
xfs_mount_t *mp)
(mp->m_dirblksize - (uint)sizeof(xfs_da_node_hdr_t)) /
(uint)sizeof(xfs_da_node_entry_t);
mp->m_dir_magicpct = (mp->m_dirblksize * 37) / 100;
+ if (xfs_sb_version_hasasciici(&mp->m_sb))
+ mp->m_dirnameops = &xfs_ascii_ci_nameops;
+ else
+ mp->m_dirnameops = &xfs_default_nameops;
}
/*
return rval;
XFS_STATS_INC(xs_dir_create);
+ memset(&args, 0, sizeof(xfs_da_args_t));
args.name = name->name;
args.namelen = name->len;
- args.hashval = xfs_da_hashname(name->name, name->len);
+ args.hashval = dp->i_mount->m_dirnameops->hashname(name);
args.inumber = inum;
args.dp = dp;
args.firstblock = first;
args.total = total;
args.whichfork = XFS_DATA_FORK;
args.trans = tp;
- args.justcheck = 0;
- args.addname = args.oknoent = 1;
+ args.op_flags = XFS_DA_OP_ADDNAME | XFS_DA_OP_OKNOENT;
if (dp->i_d.di_format == XFS_DINODE_FMT_LOCAL)
rval = xfs_dir2_sf_addname(&args);
return rval;
}
+/*
+ * If doing a CI lookup and case-insensitive match, dup actual name into
+ * args.value. Return EEXIST for success (ie. name found) or an error.
+ */
+int
+xfs_dir_cilookup_result(
+ struct xfs_da_args *args,
+ const char *name,
+ int len)
+{
+ if (args->cmpresult == XFS_CMP_DIFFERENT)
+ return ENOENT;
+ if (args->cmpresult != XFS_CMP_CASE ||
+ !(args->op_flags & XFS_DA_OP_CILOOKUP))
+ return EEXIST;
+
+ args->value = kmem_alloc(len, KM_MAYFAIL);
+ if (!args->value)
+ return ENOMEM;
+
+ memcpy(args->value, name, len);
+ args->valuelen = len;
+ return EEXIST;
+}
+
/*
* Lookup a name in a directory, give back the inode number.
+ * If ci_name is not NULL, returns the actual name in ci_name if it differs
+ * to name, or ci_name->name is set to NULL for an exact match.
*/
+
int
xfs_dir_lookup(
xfs_trans_t *tp,
xfs_inode_t *dp,
struct xfs_name *name,
- xfs_ino_t *inum) /* out: inode number */
+ xfs_ino_t *inum, /* out: inode number */
+ struct xfs_name *ci_name) /* out: actual name if CI match */
{
xfs_da_args_t args;
int rval;
ASSERT((dp->i_d.di_mode & S_IFMT) == S_IFDIR);
XFS_STATS_INC(xs_dir_lookup);
- memset(&args, 0, sizeof(xfs_da_args_t));
+ memset(&args, 0, sizeof(xfs_da_args_t));
args.name = name->name;
args.namelen = name->len;
- args.hashval = xfs_da_hashname(name->name, name->len);
+ args.hashval = dp->i_mount->m_dirnameops->hashname(name);
args.dp = dp;
args.whichfork = XFS_DATA_FORK;
args.trans = tp;
- args.oknoent = 1;
+ args.op_flags = XFS_DA_OP_OKNOENT;
+ if (ci_name)
+ args.op_flags |= XFS_DA_OP_CILOOKUP;
if (dp->i_d.di_format == XFS_DINODE_FMT_LOCAL)
rval = xfs_dir2_sf_lookup(&args);
rval = xfs_dir2_node_lookup(&args);
if (rval == EEXIST)
rval = 0;
- if (rval == 0)
+ if (!rval) {
*inum = args.inumber;
+ if (ci_name) {
+ ci_name->name = args.value;
+ ci_name->len = args.valuelen;
+ }
+ }
return rval;
}
ASSERT((dp->i_d.di_mode & S_IFMT) == S_IFDIR);
XFS_STATS_INC(xs_dir_remove);
+ memset(&args, 0, sizeof(xfs_da_args_t));
args.name = name->name;
args.namelen = name->len;
- args.hashval = xfs_da_hashname(name->name, name->len);
+ args.hashval = dp->i_mount->m_dirnameops->hashname(name);
args.inumber = ino;
args.dp = dp;
args.firstblock = first;
args.total = total;
args.whichfork = XFS_DATA_FORK;
args.trans = tp;
- args.justcheck = args.addname = args.oknoent = 0;
if (dp->i_d.di_format == XFS_DINODE_FMT_LOCAL)
rval = xfs_dir2_sf_removename(&args);
if ((rval = xfs_dir_ino_validate(tp->t_mountp, inum)))
return rval;
+ memset(&args, 0, sizeof(xfs_da_args_t));
args.name = name->name;
args.namelen = name->len;
- args.hashval = xfs_da_hashname(name->name, name->len);
+ args.hashval = dp->i_mount->m_dirnameops->hashname(name);
args.inumber = inum;
args.dp = dp;
args.firstblock = first;
args.total = total;
args.whichfork = XFS_DATA_FORK;
args.trans = tp;
- args.justcheck = args.addname = args.oknoent = 0;
if (dp->i_d.di_format == XFS_DINODE_FMT_LOCAL)
rval = xfs_dir2_sf_replace(&args);
return 0;
ASSERT((dp->i_d.di_mode & S_IFMT) == S_IFDIR);
- memset(&args, 0, sizeof(xfs_da_args_t));
+ memset(&args, 0, sizeof(xfs_da_args_t));
args.name = name->name;
args.namelen = name->len;
- args.hashval = xfs_da_hashname(name->name, name->len);
+ args.hashval = dp->i_mount->m_dirnameops->hashname(name);
args.dp = dp;
args.whichfork = XFS_DATA_FORK;
args.trans = tp;
- args.justcheck = args.addname = args.oknoent = 1;
+ args.op_flags = XFS_DA_OP_JUSTCHECK | XFS_DA_OP_ADDNAME |
+ XFS_DA_OP_OKNOENT;
if (dp->i_d.di_format == XFS_DINODE_FMT_LOCAL)
rval = xfs_dir2_sf_addname(&args);
args->firstblock, args->total,
&mapp[mapi], &nmap, args->flist,
NULL))) {
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
return error;
}
if (nmap < 1)
mapp[mapi - 1].br_startoff + mapp[mapi - 1].br_blockcount !=
bno + count) {
if (mapp != &map)
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
return XFS_ERROR(ENOSPC);
}
/*
* Done with the temporary mapping table.
*/
if (mapp != &map)
- kmem_free(mapp, sizeof(*mapp) * count);
+ kmem_free(mapp);
*dbp = xfs_dir2_da_to_db(mp, (xfs_dablk_t)bno);
/*
* Update file's size if this is the data space and it grew.
xfs_fsblock_t *first,
struct xfs_bmap_free *flist, xfs_extlen_t tot);
extern int xfs_dir_lookup(struct xfs_trans *tp, struct xfs_inode *dp,
- struct xfs_name *name, xfs_ino_t *inum);
+ struct xfs_name *name, xfs_ino_t *inum,
+ struct xfs_name *ci_name);
extern int xfs_dir_removename(struct xfs_trans *tp, struct xfs_inode *dp,
struct xfs_name *name, xfs_ino_t ino,
xfs_fsblock_t *first,
extern int xfs_dir2_shrink_inode(struct xfs_da_args *args, xfs_dir2_db_t db,
struct xfs_dabuf *bp);
+extern int xfs_dir_cilookup_result(struct xfs_da_args *args, const char *name,
+ int len);
+
#endif /* __XFS_DIR2_H__ */
/*
* If this isn't a real add, we're done with the buffer.
*/
- if (args->justcheck)
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK)
xfs_da_brelse(tp, bp);
/*
* If we don't have space for the new entry & leaf ...
* Not trying to actually do anything, or don't have
* a space reservation: return no-space.
*/
- if (args->justcheck || args->total == 0)
+ if ((args->op_flags & XFS_DA_OP_JUSTCHECK) || args->total == 0)
return XFS_ERROR(ENOSPC);
/*
* Convert to the next larger format.
/*
* Just checking, and it would work, so say so.
*/
- if (args->justcheck)
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK)
return 0;
needlog = needscan = 0;
/*
/*
* Get the offset from the leaf entry, to point to the data.
*/
- dep = (xfs_dir2_data_entry_t *)
- ((char *)block + xfs_dir2_dataptr_to_off(mp, be32_to_cpu(blp[ent].address)));
+ dep = (xfs_dir2_data_entry_t *)((char *)block +
+ xfs_dir2_dataptr_to_off(mp, be32_to_cpu(blp[ent].address)));
/*
- * Fill in inode number, release the block.
+ * Fill in inode number, CI name if appropriate, release the block.
*/
args->inumber = be64_to_cpu(dep->inumber);
+ error = xfs_dir_cilookup_result(args, dep->name, dep->namelen);
xfs_da_brelse(args->trans, bp);
- return XFS_ERROR(EEXIST);
+ return XFS_ERROR(error);
}
/*
int mid; /* binary search current idx */
xfs_mount_t *mp; /* filesystem mount point */
xfs_trans_t *tp; /* transaction pointer */
+ enum xfs_dacmp cmp; /* comparison result */
dp = args->dp;
tp = args->trans;
else
high = mid - 1;
if (low > high) {
- ASSERT(args->oknoent);
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
xfs_da_brelse(tp, bp);
return XFS_ERROR(ENOENT);
}
dep = (xfs_dir2_data_entry_t *)
((char *)block + xfs_dir2_dataptr_to_off(mp, addr));
/*
- * Compare, if it's right give back buffer & entry number.
+ * Compare name and if it's an exact match, return the index
+ * and buffer. If it's the first case-insensitive match, store
+ * the index and buffer and continue looking for an exact match.
*/
- if (dep->namelen == args->namelen &&
- dep->name[0] == args->name[0] &&
- memcmp(dep->name, args->name, args->namelen) == 0) {
+ cmp = mp->m_dirnameops->compname(args, dep->name, dep->namelen);
+ if (cmp != XFS_CMP_DIFFERENT && cmp != args->cmpresult) {
+ args->cmpresult = cmp;
*bpp = bp;
*entno = mid;
- return 0;
+ if (cmp == XFS_CMP_EXACT)
+ return 0;
}
- } while (++mid < be32_to_cpu(btp->count) && be32_to_cpu(blp[mid].hashval) == hash);
+ } while (++mid < be32_to_cpu(btp->count) &&
+ be32_to_cpu(blp[mid].hashval) == hash);
+
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
+ /*
+ * Here, we can only be doing a lookup (not a rename or replace).
+ * If a case-insensitive match was found earlier, return success.
+ */
+ if (args->cmpresult == XFS_CMP_CASE)
+ return 0;
/*
* No match, release the buffer and return ENOENT.
*/
- ASSERT(args->oknoent);
xfs_da_brelse(tp, bp);
return XFS_ERROR(ENOENT);
}
xfs_dir2_sf_t *sfp; /* shortform structure */
__be16 *tagp; /* end of data entry */
xfs_trans_t *tp; /* transaction pointer */
+ struct xfs_name name;
xfs_dir2_trace_args("sf_to_block", args);
dp = args->dp;
*/
error = xfs_dir2_grow_inode(args, XFS_DIR2_DATA_SPACE, &blkno);
if (error) {
- kmem_free(buf, buf_len);
+ kmem_free(buf);
return error;
}
/*
*/
error = xfs_dir2_data_init(args, blkno, &bp);
if (error) {
- kmem_free(buf, buf_len);
+ kmem_free(buf);
return error;
}
block = bp->data;
tagp = xfs_dir2_data_entry_tag_p(dep);
*tagp = cpu_to_be16((char *)dep - (char *)block);
xfs_dir2_data_log_entry(tp, bp, dep);
- blp[2 + i].hashval = cpu_to_be32(xfs_da_hashname(
- (char *)sfep->name, sfep->namelen));
+ name.name = sfep->name;
+ name.len = sfep->namelen;
+ blp[2 + i].hashval = cpu_to_be32(mp->m_dirnameops->
+ hashname(&name));
blp[2 + i].address = cpu_to_be32(xfs_dir2_byte_to_dataptr(mp,
(char *)dep - (char *)block));
offset = (int)((char *)(tagp + 1) - (char *)block);
sfep = xfs_dir2_sf_nextentry(sfp, sfep);
}
/* Done with the temporary buffer */
- kmem_free(buf, buf_len);
+ kmem_free(buf);
/*
* Sort the leaf entries by hash value.
*/
xfs_mount_t *mp; /* filesystem mount point */
char *p; /* current data position */
int stale; /* count of stale leaves */
+ struct xfs_name name;
mp = dp->i_mount;
d = bp->data;
addr = xfs_dir2_db_off_to_dataptr(mp, mp->m_dirdatablk,
(xfs_dir2_data_aoff_t)
((char *)dep - (char *)d));
- hash = xfs_da_hashname((char *)dep->name, dep->namelen);
+ name.name = dep->name;
+ name.len = dep->namelen;
+ hash = mp->m_dirnameops->hashname(&name);
for (i = 0; i < be32_to_cpu(btp->count); i++) {
if (be32_to_cpu(lep[i].address) == addr &&
be32_to_cpu(lep[i].hashval) == hash)
* If we don't have enough free bytes but we can make enough
* by compacting out stale entries, we'll do that.
*/
- if ((char *)bestsp - (char *)&leaf->ents[be16_to_cpu(leaf->hdr.count)] < needbytes &&
- be16_to_cpu(leaf->hdr.stale) > 1) {
+ if ((char *)bestsp - (char *)&leaf->ents[be16_to_cpu(leaf->hdr.count)] <
+ needbytes && be16_to_cpu(leaf->hdr.stale) > 1) {
compact = 1;
}
/*
* Otherwise if we don't have enough free bytes we need to
* convert to node form.
*/
- else if ((char *)bestsp - (char *)&leaf->ents[be16_to_cpu(leaf->hdr.count)] <
- needbytes) {
+ else if ((char *)bestsp - (char *)&leaf->ents[be16_to_cpu(
+ leaf->hdr.count)] < needbytes) {
/*
* Just checking or no space reservation, give up.
*/
- if (args->justcheck || args->total == 0) {
+ if ((args->op_flags & XFS_DA_OP_JUSTCHECK) ||
+ args->total == 0) {
xfs_da_brelse(tp, lbp);
return XFS_ERROR(ENOSPC);
}
* If just checking, then it will fit unless we needed to allocate
* a new data block.
*/
- if (args->justcheck) {
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK) {
xfs_da_brelse(tp, lbp);
return use_block == -1 ? XFS_ERROR(ENOSPC) : 0;
}
*offset = XFS_DIR2_MAX_DATAPTR;
else
*offset = xfs_dir2_byte_to_dataptr(mp, curoff);
- kmem_free(map, map_size * sizeof(*map));
+ kmem_free(map);
if (bp)
xfs_da_brelse(NULL, bp);
return error;
((char *)dbp->data +
xfs_dir2_dataptr_to_off(dp->i_mount, be32_to_cpu(lep->address)));
/*
- * Return the found inode number.
+ * Return the found inode number & CI name if appropriate
*/
args->inumber = be64_to_cpu(dep->inumber);
+ error = xfs_dir_cilookup_result(args, dep->name, dep->namelen);
xfs_da_brelse(tp, dbp);
xfs_da_brelse(tp, lbp);
- return XFS_ERROR(EEXIST);
+ return XFS_ERROR(error);
}
/*
int *indexp, /* out: index in leaf block */
xfs_dabuf_t **dbpp) /* out: data buffer */
{
- xfs_dir2_db_t curdb; /* current data block number */
- xfs_dabuf_t *dbp; /* data buffer */
+ xfs_dir2_db_t curdb = -1; /* current data block number */
+ xfs_dabuf_t *dbp = NULL; /* data buffer */
xfs_dir2_data_entry_t *dep; /* data entry */
xfs_inode_t *dp; /* incore directory inode */
int error; /* error return code */
xfs_mount_t *mp; /* filesystem mount point */
xfs_dir2_db_t newdb; /* new data block number */
xfs_trans_t *tp; /* transaction pointer */
+ xfs_dir2_db_t cidb = -1; /* case match data block no. */
+ enum xfs_dacmp cmp; /* name compare result */
dp = args->dp;
tp = args->trans;
/*
* Read the leaf block into the buffer.
*/
- if ((error =
- xfs_da_read_buf(tp, dp, mp->m_dirleafblk, -1, &lbp,
- XFS_DATA_FORK))) {
+ error = xfs_da_read_buf(tp, dp, mp->m_dirleafblk, -1, &lbp,
+ XFS_DATA_FORK);
+ if (error)
return error;
- }
*lbpp = lbp;
leaf = lbp->data;
xfs_dir2_leaf_check(dp, lbp);
* Loop over all the entries with the right hash value
* looking to match the name.
*/
- for (lep = &leaf->ents[index], dbp = NULL, curdb = -1;
- index < be16_to_cpu(leaf->hdr.count) && be32_to_cpu(lep->hashval) == args->hashval;
- lep++, index++) {
+ for (lep = &leaf->ents[index]; index < be16_to_cpu(leaf->hdr.count) &&
+ be32_to_cpu(lep->hashval) == args->hashval;
+ lep++, index++) {
/*
* Skip over stale leaf entries.
*/
if (newdb != curdb) {
if (dbp)
xfs_da_brelse(tp, dbp);
- if ((error =
- xfs_da_read_buf(tp, dp,
- xfs_dir2_db_to_da(mp, newdb), -1, &dbp,
- XFS_DATA_FORK))) {
+ error = xfs_da_read_buf(tp, dp,
+ xfs_dir2_db_to_da(mp, newdb),
+ -1, &dbp, XFS_DATA_FORK);
+ if (error) {
xfs_da_brelse(tp, lbp);
return error;
}
/*
* Point to the data entry.
*/
- dep = (xfs_dir2_data_entry_t *)
- ((char *)dbp->data +
- xfs_dir2_dataptr_to_off(mp, be32_to_cpu(lep->address)));
+ dep = (xfs_dir2_data_entry_t *)((char *)dbp->data +
+ xfs_dir2_dataptr_to_off(mp, be32_to_cpu(lep->address)));
/*
- * If it matches then return it.
+ * Compare name and if it's an exact match, return the index
+ * and buffer. If it's the first case-insensitive match, store
+ * the index and buffer and continue looking for an exact match.
*/
- if (dep->namelen == args->namelen &&
- dep->name[0] == args->name[0] &&
- memcmp(dep->name, args->name, args->namelen) == 0) {
- *dbpp = dbp;
+ cmp = mp->m_dirnameops->compname(args, dep->name, dep->namelen);
+ if (cmp != XFS_CMP_DIFFERENT && cmp != args->cmpresult) {
+ args->cmpresult = cmp;
*indexp = index;
- return 0;
+ /* case exact match: return the current buffer. */
+ if (cmp == XFS_CMP_EXACT) {
+ *dbpp = dbp;
+ return 0;
+ }
+ cidb = curdb;
}
}
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
+ /*
+ * Here, we can only be doing a lookup (not a rename or remove).
+ * If a case-insensitive match was found earlier, re-read the
+ * appropriate data block if required and return it.
+ */
+ if (args->cmpresult == XFS_CMP_CASE) {
+ ASSERT(cidb != -1);
+ if (cidb != curdb) {
+ xfs_da_brelse(tp, dbp);
+ error = xfs_da_read_buf(tp, dp,
+ xfs_dir2_db_to_da(mp, cidb),
+ -1, &dbp, XFS_DATA_FORK);
+ if (error) {
+ xfs_da_brelse(tp, lbp);
+ return error;
+ }
+ }
+ *dbpp = dbp;
+ return 0;
+ }
/*
* No match found, return ENOENT.
*/
- ASSERT(args->oknoent);
+ ASSERT(cidb == -1);
if (dbp)
xfs_da_brelse(tp, dbp);
xfs_da_brelse(tp, lbp);
ASSERT(index == be16_to_cpu(leaf->hdr.count) ||
be32_to_cpu(leaf->ents[index].hashval) >= args->hashval);
- if (args->justcheck)
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK)
return 0;
/*
}
/*
- * Look up a leaf entry in a node-format leaf block.
- * If this is an addname then the extrablk in state is a freespace block,
- * otherwise it's a data block.
+ * Look up a leaf entry for space to add a name in a node-format leaf block.
+ * The extrablk in state is a freespace block.
*/
-int
-xfs_dir2_leafn_lookup_int(
+STATIC int
+xfs_dir2_leafn_lookup_for_addname(
xfs_dabuf_t *bp, /* leaf buffer */
xfs_da_args_t *args, /* operation arguments */
int *indexp, /* out: leaf entry index */
xfs_da_state_t *state) /* state to fill in */
{
- xfs_dabuf_t *curbp; /* current data/free buffer */
- xfs_dir2_db_t curdb; /* current data block number */
- xfs_dir2_db_t curfdb; /* current free block number */
- xfs_dir2_data_entry_t *dep; /* data block entry */
+ xfs_dabuf_t *curbp = NULL; /* current data/free buffer */
+ xfs_dir2_db_t curdb = -1; /* current data block number */
+ xfs_dir2_db_t curfdb = -1; /* current free block number */
xfs_inode_t *dp; /* incore directory inode */
int error; /* error return value */
int fi; /* free entry index */
- xfs_dir2_free_t *free=NULL; /* free block structure */
+ xfs_dir2_free_t *free = NULL; /* free block structure */
int index; /* leaf entry index */
xfs_dir2_leaf_t *leaf; /* leaf structure */
- int length=0; /* length of new data entry */
+ int length; /* length of new data entry */
xfs_dir2_leaf_entry_t *lep; /* leaf entry */
xfs_mount_t *mp; /* filesystem mount point */
xfs_dir2_db_t newdb; /* new data block number */
/*
* Do we have a buffer coming in?
*/
- if (state->extravalid)
+ if (state->extravalid) {
+ /* If so, it's a free block buffer, get the block number. */
curbp = state->extrablk.bp;
- else
- curbp = NULL;
- /*
- * For addname, it's a free block buffer, get the block number.
- */
- if (args->addname) {
- curfdb = curbp ? state->extrablk.blkno : -1;
- curdb = -1;
- length = xfs_dir2_data_entsize(args->namelen);
- if ((free = (curbp ? curbp->data : NULL)))
- ASSERT(be32_to_cpu(free->hdr.magic) == XFS_DIR2_FREE_MAGIC);
- }
- /*
- * For others, it's a data block buffer, get the block number.
- */
- else {
- curfdb = -1;
- curdb = curbp ? state->extrablk.blkno : -1;
+ curfdb = state->extrablk.blkno;
+ free = curbp->data;
+ ASSERT(be32_to_cpu(free->hdr.magic) == XFS_DIR2_FREE_MAGIC);
}
+ length = xfs_dir2_data_entsize(args->namelen);
/*
* Loop over leaf entries with the right hash value.
*/
- for (lep = &leaf->ents[index];
- index < be16_to_cpu(leaf->hdr.count) && be32_to_cpu(lep->hashval) == args->hashval;
- lep++, index++) {
+ for (lep = &leaf->ents[index]; index < be16_to_cpu(leaf->hdr.count) &&
+ be32_to_cpu(lep->hashval) == args->hashval;
+ lep++, index++) {
/*
* Skip stale leaf entries.
*/
* For addname, we're looking for a place to put the new entry.
* We want to use a data block with an entry of equal
* hash value to ours if there is one with room.
+ *
+ * If this block isn't the data block we already have
+ * in hand, take a look at it.
*/
- if (args->addname) {
+ if (newdb != curdb) {
+ curdb = newdb;
/*
- * If this block isn't the data block we already have
- * in hand, take a look at it.
+ * Convert the data block to the free block
+ * holding its freespace information.
*/
- if (newdb != curdb) {
- curdb = newdb;
- /*
- * Convert the data block to the free block
- * holding its freespace information.
- */
- newfdb = xfs_dir2_db_to_fdb(mp, newdb);
- /*
- * If it's not the one we have in hand,
- * read it in.
- */
- if (newfdb != curfdb) {
- /*
- * If we had one before, drop it.
- */
- if (curbp)
- xfs_da_brelse(tp, curbp);
- /*
- * Read the free block.
- */
- if ((error = xfs_da_read_buf(tp, dp,
- xfs_dir2_db_to_da(mp,
- newfdb),
- -1, &curbp,
- XFS_DATA_FORK))) {
- return error;
- }
- free = curbp->data;
- ASSERT(be32_to_cpu(free->hdr.magic) ==
- XFS_DIR2_FREE_MAGIC);
- ASSERT((be32_to_cpu(free->hdr.firstdb) %
- XFS_DIR2_MAX_FREE_BESTS(mp)) ==
- 0);
- ASSERT(be32_to_cpu(free->hdr.firstdb) <= curdb);
- ASSERT(curdb <
- be32_to_cpu(free->hdr.firstdb) +
- be32_to_cpu(free->hdr.nvalid));
- }
- /*
- * Get the index for our entry.
- */
- fi = xfs_dir2_db_to_fdindex(mp, curdb);
- /*
- * If it has room, return it.
- */
- if (unlikely(be16_to_cpu(free->bests[fi]) == NULLDATAOFF)) {
- XFS_ERROR_REPORT("xfs_dir2_leafn_lookup_int",
- XFS_ERRLEVEL_LOW, mp);
- if (curfdb != newfdb)
- xfs_da_brelse(tp, curbp);
- return XFS_ERROR(EFSCORRUPTED);
- }
- curfdb = newfdb;
- if (be16_to_cpu(free->bests[fi]) >= length) {
- *indexp = index;
- state->extravalid = 1;
- state->extrablk.bp = curbp;
- state->extrablk.blkno = curfdb;
- state->extrablk.index = fi;
- state->extrablk.magic =
- XFS_DIR2_FREE_MAGIC;
- ASSERT(args->oknoent);
- return XFS_ERROR(ENOENT);
- }
- }
- }
- /*
- * Not adding a new entry, so we really want to find
- * the name given to us.
- */
- else {
+ newfdb = xfs_dir2_db_to_fdb(mp, newdb);
/*
- * If it's a different data block, go get it.
+ * If it's not the one we have in hand, read it in.
*/
- if (newdb != curdb) {
+ if (newfdb != curfdb) {
/*
- * If we had a block before, drop it.
+ * If we had one before, drop it.
*/
if (curbp)
xfs_da_brelse(tp, curbp);
/*
- * Read the data block.
+ * Read the free block.
*/
- if ((error =
- xfs_da_read_buf(tp, dp,
- xfs_dir2_db_to_da(mp, newdb), -1,
- &curbp, XFS_DATA_FORK))) {
+ error = xfs_da_read_buf(tp, dp,
+ xfs_dir2_db_to_da(mp, newfdb),
+ -1, &curbp, XFS_DATA_FORK);
+ if (error)
return error;
- }
- xfs_dir2_data_check(dp, curbp);
- curdb = newdb;
+ free = curbp->data;
+ ASSERT(be32_to_cpu(free->hdr.magic) ==
+ XFS_DIR2_FREE_MAGIC);
+ ASSERT((be32_to_cpu(free->hdr.firstdb) %
+ XFS_DIR2_MAX_FREE_BESTS(mp)) == 0);
+ ASSERT(be32_to_cpu(free->hdr.firstdb) <= curdb);
+ ASSERT(curdb < be32_to_cpu(free->hdr.firstdb) +
+ be32_to_cpu(free->hdr.nvalid));
}
/*
- * Point to the data entry.
+ * Get the index for our entry.
*/
- dep = (xfs_dir2_data_entry_t *)
- ((char *)curbp->data +
- xfs_dir2_dataptr_to_off(mp, be32_to_cpu(lep->address)));
+ fi = xfs_dir2_db_to_fdindex(mp, curdb);
/*
- * Compare the entry, return it if it matches.
+ * If it has room, return it.
*/
- if (dep->namelen == args->namelen &&
- dep->name[0] == args->name[0] &&
- memcmp(dep->name, args->name, args->namelen) == 0) {
- args->inumber = be64_to_cpu(dep->inumber);
- *indexp = index;
- state->extravalid = 1;
- state->extrablk.bp = curbp;
- state->extrablk.blkno = curdb;
- state->extrablk.index =
- (int)((char *)dep -
- (char *)curbp->data);
- state->extrablk.magic = XFS_DIR2_DATA_MAGIC;
- return XFS_ERROR(EEXIST);
+ if (unlikely(be16_to_cpu(free->bests[fi]) == NULLDATAOFF)) {
+ XFS_ERROR_REPORT("xfs_dir2_leafn_lookup_int",
+ XFS_ERRLEVEL_LOW, mp);
+ if (curfdb != newfdb)
+ xfs_da_brelse(tp, curbp);
+ return XFS_ERROR(EFSCORRUPTED);
}
+ curfdb = newfdb;
+ if (be16_to_cpu(free->bests[fi]) >= length)
+ goto out;
}
}
+ /* Didn't find any space */
+ fi = -1;
+out:
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
+ if (curbp) {
+ /* Giving back a free block. */
+ state->extravalid = 1;
+ state->extrablk.bp = curbp;
+ state->extrablk.index = fi;
+ state->extrablk.blkno = curfdb;
+ state->extrablk.magic = XFS_DIR2_FREE_MAGIC;
+ } else {
+ state->extravalid = 0;
+ }
/*
- * Didn't find a match.
- * If we are holding a buffer, give it back in case our caller
- * finds it useful.
+ * Return the index, that will be the insertion point.
*/
- if ((state->extravalid = (curbp != NULL))) {
- state->extrablk.bp = curbp;
- state->extrablk.index = -1;
+ *indexp = index;
+ return XFS_ERROR(ENOENT);
+}
+
+/*
+ * Look up a leaf entry in a node-format leaf block.
+ * The extrablk in state a data block.
+ */
+STATIC int
+xfs_dir2_leafn_lookup_for_entry(
+ xfs_dabuf_t *bp, /* leaf buffer */
+ xfs_da_args_t *args, /* operation arguments */
+ int *indexp, /* out: leaf entry index */
+ xfs_da_state_t *state) /* state to fill in */
+{
+ xfs_dabuf_t *curbp = NULL; /* current data/free buffer */
+ xfs_dir2_db_t curdb = -1; /* current data block number */
+ xfs_dir2_data_entry_t *dep; /* data block entry */
+ xfs_inode_t *dp; /* incore directory inode */
+ int error; /* error return value */
+ int index; /* leaf entry index */
+ xfs_dir2_leaf_t *leaf; /* leaf structure */
+ xfs_dir2_leaf_entry_t *lep; /* leaf entry */
+ xfs_mount_t *mp; /* filesystem mount point */
+ xfs_dir2_db_t newdb; /* new data block number */
+ xfs_trans_t *tp; /* transaction pointer */
+ enum xfs_dacmp cmp; /* comparison result */
+
+ dp = args->dp;
+ tp = args->trans;
+ mp = dp->i_mount;
+ leaf = bp->data;
+ ASSERT(be16_to_cpu(leaf->hdr.info.magic) == XFS_DIR2_LEAFN_MAGIC);
+#ifdef __KERNEL__
+ ASSERT(be16_to_cpu(leaf->hdr.count) > 0);
+#endif
+ xfs_dir2_leafn_check(dp, bp);
+ /*
+ * Look up the hash value in the leaf entries.
+ */
+ index = xfs_dir2_leaf_search_hash(args, bp);
+ /*
+ * Do we have a buffer coming in?
+ */
+ if (state->extravalid) {
+ curbp = state->extrablk.bp;
+ curdb = state->extrablk.blkno;
+ }
+ /*
+ * Loop over leaf entries with the right hash value.
+ */
+ for (lep = &leaf->ents[index]; index < be16_to_cpu(leaf->hdr.count) &&
+ be32_to_cpu(lep->hashval) == args->hashval;
+ lep++, index++) {
/*
- * For addname, giving back a free block.
+ * Skip stale leaf entries.
*/
- if (args->addname) {
- state->extrablk.blkno = curfdb;
- state->extrablk.magic = XFS_DIR2_FREE_MAGIC;
+ if (be32_to_cpu(lep->address) == XFS_DIR2_NULL_DATAPTR)
+ continue;
+ /*
+ * Pull the data block number from the entry.
+ */
+ newdb = xfs_dir2_dataptr_to_db(mp, be32_to_cpu(lep->address));
+ /*
+ * Not adding a new entry, so we really want to find
+ * the name given to us.
+ *
+ * If it's a different data block, go get it.
+ */
+ if (newdb != curdb) {
+ /*
+ * If we had a block before that we aren't saving
+ * for a CI name, drop it
+ */
+ if (curbp && (args->cmpresult == XFS_CMP_DIFFERENT ||
+ curdb != state->extrablk.blkno))
+ xfs_da_brelse(tp, curbp);
+ /*
+ * If needing the block that is saved with a CI match,
+ * use it otherwise read in the new data block.
+ */
+ if (args->cmpresult != XFS_CMP_DIFFERENT &&
+ newdb == state->extrablk.blkno) {
+ ASSERT(state->extravalid);
+ curbp = state->extrablk.bp;
+ } else {
+ error = xfs_da_read_buf(tp, dp,
+ xfs_dir2_db_to_da(mp, newdb),
+ -1, &curbp, XFS_DATA_FORK);
+ if (error)
+ return error;
+ }
+ xfs_dir2_data_check(dp, curbp);
+ curdb = newdb;
}
/*
- * For other callers, giving back a data block.
+ * Point to the data entry.
*/
- else {
+ dep = (xfs_dir2_data_entry_t *)((char *)curbp->data +
+ xfs_dir2_dataptr_to_off(mp, be32_to_cpu(lep->address)));
+ /*
+ * Compare the entry and if it's an exact match, return
+ * EEXIST immediately. If it's the first case-insensitive
+ * match, store the block & inode number and continue looking.
+ */
+ cmp = mp->m_dirnameops->compname(args, dep->name, dep->namelen);
+ if (cmp != XFS_CMP_DIFFERENT && cmp != args->cmpresult) {
+ /* If there is a CI match block, drop it */
+ if (args->cmpresult != XFS_CMP_DIFFERENT &&
+ curdb != state->extrablk.blkno)
+ xfs_da_brelse(tp, state->extrablk.bp);
+ args->cmpresult = cmp;
+ args->inumber = be64_to_cpu(dep->inumber);
+ *indexp = index;
+ state->extravalid = 1;
+ state->extrablk.bp = curbp;
state->extrablk.blkno = curdb;
+ state->extrablk.index = (int)((char *)dep -
+ (char *)curbp->data);
state->extrablk.magic = XFS_DIR2_DATA_MAGIC;
+ if (cmp == XFS_CMP_EXACT)
+ return XFS_ERROR(EEXIST);
}
}
- /*
- * Return the final index, that will be the insertion point.
- */
+ ASSERT(index == be16_to_cpu(leaf->hdr.count) ||
+ (args->op_flags & XFS_DA_OP_OKNOENT));
+ if (curbp) {
+ if (args->cmpresult == XFS_CMP_DIFFERENT) {
+ /* Giving back last used data block. */
+ state->extravalid = 1;
+ state->extrablk.bp = curbp;
+ state->extrablk.index = -1;
+ state->extrablk.blkno = curdb;
+ state->extrablk.magic = XFS_DIR2_DATA_MAGIC;
+ } else {
+ /* If the curbp is not the CI match block, drop it */
+ if (state->extrablk.bp != curbp)
+ xfs_da_brelse(tp, curbp);
+ }
+ } else {
+ state->extravalid = 0;
+ }
*indexp = index;
- ASSERT(index == be16_to_cpu(leaf->hdr.count) || args->oknoent);
return XFS_ERROR(ENOENT);
}
+/*
+ * Look up a leaf entry in a node-format leaf block.
+ * If this is an addname then the extrablk in state is a freespace block,
+ * otherwise it's a data block.
+ */
+int
+xfs_dir2_leafn_lookup_int(
+ xfs_dabuf_t *bp, /* leaf buffer */
+ xfs_da_args_t *args, /* operation arguments */
+ int *indexp, /* out: leaf entry index */
+ xfs_da_state_t *state) /* state to fill in */
+{
+ if (args->op_flags & XFS_DA_OP_ADDNAME)
+ return xfs_dir2_leafn_lookup_for_addname(bp, args, indexp,
+ state);
+ return xfs_dir2_leafn_lookup_for_entry(bp, args, indexp, state);
+}
+
/*
* Move count leaf entries from source to destination leaf.
* Log entries and headers. Stale entries are preserved.
*/
if (!state->inleaf)
blk2->index = blk1->index - be16_to_cpu(leaf1->hdr.count);
-
- /*
- * Finally sanity check just to make sure we are not returning a negative index
+
+ /*
+ * Finally sanity check just to make sure we are not returning a
+ * negative index
*/
if(blk2->index < 0) {
state->inleaf = 1;
/*
* It worked, fix the hash values up the btree.
*/
- if (!args->justcheck)
+ if (!(args->op_flags & XFS_DA_OP_JUSTCHECK))
xfs_da_fixhashpath(state, &state->path);
} else {
/*
/*
* Not allowed to allocate, return failure.
*/
- if (args->justcheck || args->total == 0) {
+ if ((args->op_flags & XFS_DA_OP_JUSTCHECK) ||
+ args->total == 0) {
/*
* Drop the freespace buffer unless it came from our
* caller.
/*
* If just checking, we succeeded.
*/
- if (args->justcheck) {
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK) {
if ((fblk == NULL || fblk->bp == NULL) && fbp != NULL)
xfs_da_buf_done(fbp);
return 0;
error = xfs_da_node_lookup_int(state, &rval);
if (error)
rval = error;
+ else if (rval == ENOENT && args->cmpresult == XFS_CMP_CASE) {
+ /* If a CI match, dup the actual name and return EEXIST */
+ xfs_dir2_data_entry_t *dep;
+
+ dep = (xfs_dir2_data_entry_t *)((char *)state->extrablk.bp->
+ data + state->extrablk.index);
+ rval = xfs_dir_cilookup_result(args, dep->name, dep->namelen);
+ }
/*
* Release the btree blocks and leaf block.
*/
* Look up the entry we're deleting, set up the cursor.
*/
error = xfs_da_node_lookup_int(state, &rval);
- if (error) {
+ if (error)
rval = error;
- }
/*
* Didn't find it, upper layer screwed up.
*/
*/
error = xfs_dir2_leafn_remove(args, blk->bp, blk->index,
&state->extrablk, &rval);
- if (error) {
+ if (error)
return error;
- }
/*
* Fix the hash values up the btree.
*/
xfs_dir2_sf_check(args);
out:
xfs_trans_log_inode(args->trans, dp, logflags);
- kmem_free(block, mp->m_dirblksize);
+ kmem_free(block);
return error;
}
/*
* Just checking or no space reservation, it doesn't fit.
*/
- if (args->justcheck || args->total == 0)
+ if ((args->op_flags & XFS_DA_OP_JUSTCHECK) || args->total == 0)
return XFS_ERROR(ENOSPC);
/*
* Convert to block form then add the name.
/*
* Just checking, it fits.
*/
- if (args->justcheck)
+ if (args->op_flags & XFS_DA_OP_JUSTCHECK)
return 0;
/*
* Do it the easy way - just add it at the end.
sfep = xfs_dir2_sf_nextentry(sfp, sfep);
memcpy(sfep, oldsfep, old_isize - nbytes);
}
- kmem_free(buf, old_isize);
+ kmem_free(buf);
dp->i_d.di_size = new_isize;
xfs_dir2_sf_check(args);
}
{
xfs_inode_t *dp; /* incore directory inode */
int i; /* entry index */
+ int error;
xfs_dir2_sf_entry_t *sfep; /* shortform directory entry */
xfs_dir2_sf_t *sfp; /* shortform structure */
+ enum xfs_dacmp cmp; /* comparison result */
+ xfs_dir2_sf_entry_t *ci_sfep; /* case-insens. entry */
xfs_dir2_trace_args("sf_lookup", args);
xfs_dir2_sf_check(args);
*/
if (args->namelen == 1 && args->name[0] == '.') {
args->inumber = dp->i_ino;
+ args->cmpresult = XFS_CMP_EXACT;
return XFS_ERROR(EEXIST);
}
/*
if (args->namelen == 2 &&
args->name[0] == '.' && args->name[1] == '.') {
args->inumber = xfs_dir2_sf_get_inumber(sfp, &sfp->hdr.parent);
+ args->cmpresult = XFS_CMP_EXACT;
return XFS_ERROR(EEXIST);
}
/*
* Loop over all the entries trying to match ours.
*/
- for (i = 0, sfep = xfs_dir2_sf_firstentry(sfp);
- i < sfp->hdr.count;
- i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
- if (sfep->namelen == args->namelen &&
- sfep->name[0] == args->name[0] &&
- memcmp(args->name, sfep->name, args->namelen) == 0) {
- args->inumber =
- xfs_dir2_sf_get_inumber(sfp,
- xfs_dir2_sf_inumberp(sfep));
- return XFS_ERROR(EEXIST);
+ ci_sfep = NULL;
+ for (i = 0, sfep = xfs_dir2_sf_firstentry(sfp); i < sfp->hdr.count;
+ i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
+ /*
+ * Compare name and if it's an exact match, return the inode
+ * number. If it's the first case-insensitive match, store the
+ * inode number and continue looking for an exact match.
+ */
+ cmp = dp->i_mount->m_dirnameops->compname(args, sfep->name,
+ sfep->namelen);
+ if (cmp != XFS_CMP_DIFFERENT && cmp != args->cmpresult) {
+ args->cmpresult = cmp;
+ args->inumber = xfs_dir2_sf_get_inumber(sfp,
+ xfs_dir2_sf_inumberp(sfep));
+ if (cmp == XFS_CMP_EXACT)
+ return XFS_ERROR(EEXIST);
+ ci_sfep = sfep;
}
}
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
/*
- * Didn't find it.
+ * Here, we can only be doing a lookup (not a rename or replace).
+ * If a case-insensitive match was not found, return ENOENT.
*/
- ASSERT(args->oknoent);
- return XFS_ERROR(ENOENT);
+ if (!ci_sfep)
+ return XFS_ERROR(ENOENT);
+ /* otherwise process the CI match as required by the caller */
+ error = xfs_dir_cilookup_result(args, ci_sfep->name, ci_sfep->namelen);
+ return XFS_ERROR(error);
}
/*
* Loop over the old directory entries.
* Find the one we're deleting.
*/
- for (i = 0, sfep = xfs_dir2_sf_firstentry(sfp);
- i < sfp->hdr.count;
- i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
- if (sfep->namelen == args->namelen &&
- sfep->name[0] == args->name[0] &&
- memcmp(sfep->name, args->name, args->namelen) == 0) {
+ for (i = 0, sfep = xfs_dir2_sf_firstentry(sfp); i < sfp->hdr.count;
+ i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
+ if (xfs_da_compname(args, sfep->name, sfep->namelen) ==
+ XFS_CMP_EXACT) {
ASSERT(xfs_dir2_sf_get_inumber(sfp,
- xfs_dir2_sf_inumberp(sfep)) ==
- args->inumber);
+ xfs_dir2_sf_inumberp(sfep)) ==
+ args->inumber);
break;
}
}
/*
* Didn't find it.
*/
- if (i == sfp->hdr.count) {
+ if (i == sfp->hdr.count)
return XFS_ERROR(ENOENT);
- }
/*
* Calculate sizes.
*/
*/
else {
for (i = 0, sfep = xfs_dir2_sf_firstentry(sfp);
- i < sfp->hdr.count;
- i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
- if (sfep->namelen == args->namelen &&
- sfep->name[0] == args->name[0] &&
- memcmp(args->name, sfep->name, args->namelen) == 0) {
+ i < sfp->hdr.count;
+ i++, sfep = xfs_dir2_sf_nextentry(sfp, sfep)) {
+ if (xfs_da_compname(args, sfep->name, sfep->namelen) ==
+ XFS_CMP_EXACT) {
#if XFS_BIG_INUMS || defined(DEBUG)
ino = xfs_dir2_sf_get_inumber(sfp,
xfs_dir2_sf_inumberp(sfep));
* Didn't find it.
*/
if (i == sfp->hdr.count) {
- ASSERT(args->oknoent);
+ ASSERT(args->op_flags & XFS_DA_OP_OKNOENT);
#if XFS_BIG_INUMS
if (i8elevated)
xfs_dir2_sf_toino4(args);
/*
* Clean up the inode.
*/
- kmem_free(buf, oldsize);
+ kmem_free(buf);
dp->i_d.di_size = newsize;
xfs_trans_log_inode(args->trans, dp, XFS_ILOG_CORE | XFS_ILOG_DDATA);
}
/*
* Clean up the inode.
*/
- kmem_free(buf, oldsize);
+ kmem_free(buf);
dp->i_d.di_size = newsize;
xfs_trans_log_inode(args->trans, dp, XFS_ILOG_CORE | XFS_ILOG_DDATA);
}
* Normalized offset (in a data block) of the entry, really xfs_dir2_data_off_t.
* Only need 16 bits, this is the byte offset into the single block form.
*/
-typedef struct { __uint8_t i[2]; } xfs_dir2_sf_off_t;
+typedef struct { __uint8_t i[2]; } __arch_pack xfs_dir2_sf_off_t;
/*
* The parent directory has a dedicated field, and the self-pointer must
__uint8_t count; /* count of entries */
__uint8_t i8count; /* count of 8-byte inode #s */
xfs_dir2_inou_t parent; /* parent dir inode number */
-} xfs_dir2_sf_hdr_t;
+} __arch_pack xfs_dir2_sf_hdr_t;
typedef struct xfs_dir2_sf_entry {
__uint8_t namelen; /* actual name length */
xfs_dir2_sf_off_t offset; /* saved offset */
__uint8_t name[1]; /* name, variable size */
xfs_dir2_inou_t inumber; /* inode number, var. offset */
-} xfs_dir2_sf_entry_t;
+} __arch_pack xfs_dir2_sf_entry_t;
typedef struct xfs_dir2_sf {
xfs_dir2_sf_hdr_t hdr; /* shortform header */
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck, NULL, NULL);
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
+ NULL, NULL);
}
void
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck,
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
(void *)(bp ? bp->bps[0] : NULL), NULL);
}
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck,
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
(void *)(lbp ? lbp->bps[0] : NULL),
(void *)(dbp ? dbp->bps[0] : NULL));
}
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck, (void *)(long)db,
- (void *)dbp);
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
+ (void *)(long)db, (void *)dbp);
}
void
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck,
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
(void *)((unsigned long)(i >> 32)),
(void *)((unsigned long)(i & 0xFFFFFFFF)));
}
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck, (void *)(long)s, NULL);
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
+ (void *)(long)s, NULL);
}
void
(void *)((unsigned long)(args->inumber >> 32)),
(void *)((unsigned long)(args->inumber & 0xFFFFFFFF)),
(void *)args->dp, (void *)args->trans,
- (void *)(unsigned long)args->justcheck, (void *)(long)s,
- (void *)dbp);
+ (void *)(unsigned long)(args->op_flags & XFS_DA_OP_JUSTCHECK),
+ (void *)(long)s, (void *)dbp);
}
#endif /* XFS_DIR2_TRACE */
#define FILP_DELAY_FLAG(filp) ((filp->f_flags&(O_NDELAY|O_NONBLOCK)) ? \
DM_FLAGS_NDELAY : 0)
-#define AT_DELAY_FLAG(f) ((f&ATTR_NONBLOCK) ? DM_FLAGS_NDELAY : 0)
+#define AT_DELAY_FLAG(f) ((f & XFS_ATTR_NONBLOCK) ? DM_FLAGS_NDELAY : 0)
#endif /* __XFS_DMAPI_H__ */
int64_t xfs_etest_fsid[XFS_NUM_INJECT_ERROR];
char * xfs_etest_fsname[XFS_NUM_INJECT_ERROR];
-void
-xfs_error_test_init(void)
-{
- memset(xfs_etest, 0, sizeof(xfs_etest));
- memset(xfs_etest_fsid, 0, sizeof(xfs_etest_fsid));
- memset(xfs_etest_fsname, 0, sizeof(xfs_etest_fsname));
-}
-
int
xfs_error_test(int error_tag, int *fsidp, char *expression,
int line, char *file, unsigned long randfactor)
xfs_etest[i]);
xfs_etest[i] = 0;
xfs_etest_fsid[i] = 0LL;
- kmem_free(xfs_etest_fsname[i],
- strlen(xfs_etest_fsname[i]) + 1);
+ kmem_free(xfs_etest_fsname[i]);
xfs_etest_fsname[i] = NULL;
}
}
newfmt = kmem_alloc(len, KM_SLEEP);
sprintf(newfmt, "Filesystem \"%s\": %s", mp->m_fsname, fmt);
icmn_err(level, newfmt, ap);
- kmem_free(newfmt, len);
+ kmem_free(newfmt);
} else {
icmn_err(level, fmt, ap);
}
#if (defined(DEBUG) || defined(INDUCE_IO_ERROR))
extern int xfs_error_test(int, int *, char *, int, char *, unsigned long);
-extern void xfs_error_test_init(void);
#define XFS_NUM_INJECT_ERROR 10
int nexts = efip->efi_format.efi_nextents;
if (nexts > XFS_EFI_MAX_FAST_EXTENTS) {
- kmem_free(efip, sizeof(xfs_efi_log_item_t) +
- (nexts - 1) * sizeof(xfs_extent_t));
+ kmem_free(efip);
} else {
kmem_zone_free(xfs_efi_zone, efip);
}
int nexts = efdp->efd_format.efd_nextents;
if (nexts > XFS_EFD_MAX_FAST_EXTENTS) {
- kmem_free(efdp, sizeof(xfs_efd_log_item_t) +
- (nexts - 1) * sizeof(xfs_extent_t));
+ kmem_free(efdp);
} else {
kmem_zone_free(xfs_efd_zone, efdp);
}
xfs_filestream_init(void)
{
item_zone = kmem_zone_init(sizeof(fstrm_item_t), "fstrm_item");
+ if (!item_zone)
+ return -ENOMEM;
#ifdef XFS_FILESTREAMS_TRACE
xfs_filestreams_trace_buf = ktrace_alloc(XFS_FSTRM_KTRACE_SIZE, KM_SLEEP);
#endif
- return item_zone ? 0 : -ENOMEM;
+ return 0;
}
/*
#define XFS_FSOP_GEOM_FLAGS_LOGV2 0x0100 /* log format version 2 */
#define XFS_FSOP_GEOM_FLAGS_SECTOR 0x0200 /* sector sizes >1BB */
#define XFS_FSOP_GEOM_FLAGS_ATTR2 0x0400 /* inline attributes rework */
+#define XFS_FSOP_GEOM_FLAGS_DIRV2CI 0x1000 /* ASCII only CI names */
#define XFS_FSOP_GEOM_FLAGS_LAZYSB 0x4000 /* lazy superblock counters */
typedef struct xfs_attr_multiop {
__u32 am_opcode;
+#define ATTR_OP_GET 1 /* return the indicated attr's value */
+#define ATTR_OP_SET 2 /* set/create the indicated attr/value pair */
+#define ATTR_OP_REMOVE 3 /* remove the indicated attr */
__s32 am_error;
void __user *am_attrname;
void __user *am_attrvalue;
XFS_FSOP_GEOM_FLAGS_DIRV2 : 0) |
(xfs_sb_version_hassector(&mp->m_sb) ?
XFS_FSOP_GEOM_FLAGS_SECTOR : 0) |
+ (xfs_sb_version_hasasciici(&mp->m_sb) ?
+ XFS_FSOP_GEOM_FLAGS_DIRV2CI : 0) |
(xfs_sb_version_haslazysbcount(&mp->m_sb) ?
XFS_FSOP_GEOM_FLAGS_LAZYSB : 0) |
(xfs_sb_version_hasattr2(&mp->m_sb) ?
xfs_force_shutdown(mp, SHUTDOWN_FORCE_UMOUNT);
thaw_bdev(sb->s_bdev, sb);
}
-
+
break;
}
case XFS_FSOP_GOING_FLAGS_LOGFLUSH:
return 0;
}
-
-/*
- * xfs_igrow_start
- *
- * Do the first part of growing a file: zero any data in the last
- * block that is beyond the old EOF. We need to do this before
- * the inode is joined to the transaction to modify the i_size.
- * That way we can drop the inode lock and call into the buffer
- * cache to get the buffer mapping the EOF.
- */
-int
-xfs_igrow_start(
- xfs_inode_t *ip,
- xfs_fsize_t new_size,
- cred_t *credp)
-{
- ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL|XFS_IOLOCK_EXCL));
- ASSERT(new_size > ip->i_size);
-
- /*
- * Zero any pages that may have been created by
- * xfs_write_file() beyond the end of the file
- * and any blocks between the old and new file sizes.
- */
- return xfs_zero_eof(ip, new_size, ip->i_size);
-}
-
-/*
- * xfs_igrow_finish
- *
- * This routine is called to extend the size of a file.
- * The inode must have both the iolock and the ilock locked
- * for update and it must be a part of the current transaction.
- * The xfs_igrow_start() function must have been called previously.
- * If the change_flag is not zero, the inode change timestamp will
- * be updated.
- */
-void
-xfs_igrow_finish(
- xfs_trans_t *tp,
- xfs_inode_t *ip,
- xfs_fsize_t new_size,
- int change_flag)
-{
- ASSERT(xfs_isilocked(ip, XFS_ILOCK_EXCL|XFS_IOLOCK_EXCL));
- ASSERT(ip->i_transp == tp);
- ASSERT(new_size > ip->i_size);
-
- /*
- * Update the file size. Update the inode change timestamp
- * if change_flag set.
- */
- ip->i_d.di_size = new_size;
- ip->i_size = new_size;
- if (change_flag)
- xfs_ichgtime(ip, XFS_ICHGTIME_CHG);
- xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
-
-}
-
-
/*
* This is called when the inode's link count goes to 0.
* We place the on-disk inode on a list in the AGI. It
xfs_trans_binval(tp, bp);
}
- kmem_free(ip_found, ninodes * sizeof(xfs_inode_t *));
+ kmem_free(ip_found);
xfs_put_perag(mp, pag);
}
(int)new_size);
memcpy(np, op, new_max * (uint)sizeof(xfs_dfsbno_t));
}
- kmem_free(ifp->if_broot, ifp->if_broot_bytes);
+ kmem_free(ifp->if_broot);
ifp->if_broot = new_broot;
ifp->if_broot_bytes = (int)new_size;
ASSERT(ifp->if_broot_bytes <=
if (new_size == 0) {
if (ifp->if_u1.if_data != ifp->if_u2.if_inline_data) {
- kmem_free(ifp->if_u1.if_data, ifp->if_real_bytes);
+ kmem_free(ifp->if_u1.if_data);
}
ifp->if_u1.if_data = NULL;
real_size = 0;
ASSERT(ifp->if_real_bytes != 0);
memcpy(ifp->if_u2.if_inline_data, ifp->if_u1.if_data,
new_size);
- kmem_free(ifp->if_u1.if_data, ifp->if_real_bytes);
+ kmem_free(ifp->if_u1.if_data);
ifp->if_u1.if_data = ifp->if_u2.if_inline_data;
}
real_size = 0;
ifp = XFS_IFORK_PTR(ip, whichfork);
if (ifp->if_broot != NULL) {
- kmem_free(ifp->if_broot, ifp->if_broot_bytes);
+ kmem_free(ifp->if_broot);
ifp->if_broot = NULL;
}
if ((ifp->if_u1.if_data != ifp->if_u2.if_inline_data) &&
(ifp->if_u1.if_data != NULL)) {
ASSERT(ifp->if_real_bytes != 0);
- kmem_free(ifp->if_u1.if_data, ifp->if_real_bytes);
+ kmem_free(ifp->if_u1.if_data);
ifp->if_u1.if_data = NULL;
ifp->if_real_bytes = 0;
}
out_free:
read_unlock(&pag->pag_ici_lock);
- kmem_free(ilist, ilist_size);
+ kmem_free(ilist);
return 0;
* Unlocks the flush lock
*/
xfs_iflush_abort(iq);
- kmem_free(ilist, ilist_size);
+ kmem_free(ilist);
return XFS_ERROR(EFSCORRUPTED);
}
* flush lock and do nothing.
*/
if (xfs_inode_clean(ip)) {
- ASSERT((iip != NULL) ?
- !(iip->ili_item.li_flags & XFS_LI_IN_AIL) : 1);
xfs_ifunlock(ip);
return 0;
}
erp = xfs_iext_irec_new(ifp, erp_idx);
}
memmove(&erp->er_extbuf[i], nex2_ep, byte_diff);
- kmem_free(nex2_ep, byte_diff);
+ kmem_free(nex2_ep);
erp->er_extcount += nex2;
xfs_iext_irec_update_extoffs(ifp, erp_idx + 1, nex2);
}
*/
memcpy(ifp->if_u2.if_inline_ext, ifp->if_u1.if_extents,
nextents * sizeof(xfs_bmbt_rec_t));
- kmem_free(ifp->if_u1.if_extents, ifp->if_real_bytes);
+ kmem_free(ifp->if_u1.if_extents);
ifp->if_u1.if_extents = ifp->if_u2.if_inline_ext;
ifp->if_real_bytes = 0;
}
ASSERT(ifp->if_real_bytes == XFS_IEXT_BUFSZ);
ep = ifp->if_u1.if_ext_irec->er_extbuf;
- kmem_free(ifp->if_u1.if_ext_irec, sizeof(xfs_ext_irec_t));
+ kmem_free(ifp->if_u1.if_ext_irec);
ifp->if_flags &= ~XFS_IFEXTIREC;
ifp->if_u1.if_extents = ep;
ifp->if_bytes = size;
}
ifp->if_flags &= ~XFS_IFEXTIREC;
} else if (ifp->if_real_bytes) {
- kmem_free(ifp->if_u1.if_extents, ifp->if_real_bytes);
+ kmem_free(ifp->if_u1.if_extents);
} else if (ifp->if_bytes) {
memset(ifp->if_u2.if_inline_ext, 0, XFS_INLINE_EXTS *
sizeof(xfs_bmbt_rec_t));
if (erp->er_extbuf) {
xfs_iext_irec_update_extoffs(ifp, erp_idx + 1,
-erp->er_extcount);
- kmem_free(erp->er_extbuf, XFS_IEXT_BUFSZ);
+ kmem_free(erp->er_extbuf);
}
/* Compact extent records */
erp = ifp->if_u1.if_ext_irec;
xfs_iext_realloc_indirect(ifp,
nlists * sizeof(xfs_ext_irec_t));
} else {
- kmem_free(ifp->if_u1.if_ext_irec,
- sizeof(xfs_ext_irec_t));
+ kmem_free(ifp->if_u1.if_ext_irec);
}
ifp->if_real_bytes = nlists * XFS_IEXT_BUFSZ;
}
* so er_extoffs don't get modified in
* xfs_iext_irec_remove.
*/
- kmem_free(erp_next->er_extbuf, XFS_IEXT_BUFSZ);
+ kmem_free(erp_next->er_extbuf);
erp_next->er_extbuf = NULL;
xfs_iext_irec_remove(ifp, erp_idx + 1);
nlists = ifp->if_real_bytes / XFS_IEXT_BUFSZ;
int nlists; /* number of irec's (ex lists) */
ASSERT(ifp->if_flags & XFS_IFEXTIREC);
+
nlists = ifp->if_real_bytes / XFS_IEXT_BUFSZ;
erp = ifp->if_u1.if_ext_irec;
ep = &erp->er_extbuf[erp->er_extcount];
erp_next = erp + 1;
ep_next = erp_next->er_extbuf;
+
while (erp_idx < nlists - 1) {
+ /*
+ * Check how many extent records are available in this irec.
+ * If there is none skip the whole exercise.
+ */
ext_avail = XFS_LINEAR_EXTS - erp->er_extcount;
- ext_diff = MIN(ext_avail, erp_next->er_extcount);
- memcpy(ep, ep_next, ext_diff * sizeof(xfs_bmbt_rec_t));
- erp->er_extcount += ext_diff;
- erp_next->er_extcount -= ext_diff;
- /* Remove next page */
- if (erp_next->er_extcount == 0) {
+ if (ext_avail) {
+
/*
- * Free page before removing extent record
- * so er_extoffs don't get modified in
- * xfs_iext_irec_remove.
+ * Copy over as many as possible extent records into
+ * the previous page.
*/
- kmem_free(erp_next->er_extbuf,
- erp_next->er_extcount * sizeof(xfs_bmbt_rec_t));
- erp_next->er_extbuf = NULL;
- xfs_iext_irec_remove(ifp, erp_idx + 1);
- erp = &ifp->if_u1.if_ext_irec[erp_idx];
- nlists = ifp->if_real_bytes / XFS_IEXT_BUFSZ;
- /* Update next page */
- } else {
- /* Move rest of page up to become next new page */
- memmove(erp_next->er_extbuf, ep_next,
- erp_next->er_extcount * sizeof(xfs_bmbt_rec_t));
- ep_next = erp_next->er_extbuf;
- memset(&ep_next[erp_next->er_extcount], 0,
- (XFS_LINEAR_EXTS - erp_next->er_extcount) *
- sizeof(xfs_bmbt_rec_t));
+ ext_diff = MIN(ext_avail, erp_next->er_extcount);
+ memcpy(ep, ep_next, ext_diff * sizeof(xfs_bmbt_rec_t));
+ erp->er_extcount += ext_diff;
+ erp_next->er_extcount -= ext_diff;
+
+ /*
+ * If the next irec is empty now we can simply
+ * remove it.
+ */
+ if (erp_next->er_extcount == 0) {
+ /*
+ * Free page before removing extent record
+ * so er_extoffs don't get modified in
+ * xfs_iext_irec_remove.
+ */
+ kmem_free(erp_next->er_extbuf);
+ erp_next->er_extbuf = NULL;
+ xfs_iext_irec_remove(ifp, erp_idx + 1);
+ erp = &ifp->if_u1.if_ext_irec[erp_idx];
+ nlists = ifp->if_real_bytes / XFS_IEXT_BUFSZ;
+
+ /*
+ * If the next irec is not empty move up the content
+ * that has not been copied to the previous page to
+ * the beggining of this one.
+ */
+ } else {
+ memmove(erp_next->er_extbuf, &ep_next[ext_diff],
+ erp_next->er_extcount *
+ sizeof(xfs_bmbt_rec_t));
+ ep_next = erp_next->er_extbuf;
+ memset(&ep_next[erp_next->er_extcount], 0,
+ (XFS_LINEAR_EXTS -
+ erp_next->er_extcount) *
+ sizeof(xfs_bmbt_rec_t));
+ }
}
+
if (erp->er_extcount == XFS_LINEAR_EXTS) {
erp_idx++;
if (erp_idx < nlists)
int xfs_itruncate_finish(struct xfs_trans **, xfs_inode_t *,
xfs_fsize_t, int, int);
int xfs_iunlink(struct xfs_trans *, xfs_inode_t *);
-int xfs_igrow_start(xfs_inode_t *, xfs_fsize_t, struct cred *);
-void xfs_igrow_finish(struct xfs_trans *, xfs_inode_t *,
- xfs_fsize_t, int);
void xfs_idestroy_fork(xfs_inode_t *, int);
void xfs_idestroy(xfs_inode_t *);
ASSERT(ip->i_d.di_nextents > 0);
ASSERT(iip->ili_format.ilf_fields & XFS_ILOG_DEXT);
ASSERT(ip->i_df.if_bytes > 0);
- kmem_free(iip->ili_extents_buf, ip->i_df.if_bytes);
+ kmem_free(iip->ili_extents_buf);
iip->ili_extents_buf = NULL;
}
if (iip->ili_aextents_buf != NULL) {
ASSERT(ip->i_d.di_anextents > 0);
ASSERT(iip->ili_format.ilf_fields & XFS_ILOG_AEXT);
ASSERT(ip->i_afp->if_bytes > 0);
- kmem_free(iip->ili_aextents_buf, ip->i_afp->if_bytes);
+ kmem_free(iip->ili_aextents_buf);
iip->ili_aextents_buf = NULL;
}
{
#ifdef XFS_TRANS_DEBUG
if (ip->i_itemp->ili_root_size != 0) {
- kmem_free(ip->i_itemp->ili_orig_root,
- ip->i_itemp->ili_root_size);
+ kmem_free(ip->i_itemp->ili_orig_root);
}
#endif
kmem_zone_free(xfs_ili_zone, ip->i_itemp);
count_fsb = XFS_B_TO_FSB(mp, (xfs_ufsize_t)offset + count);
count_fsb = (xfs_filblks_t)(count_fsb - offset_fsb);
+ /*
+ * Reserve enough blocks in this transaction for two complete extent
+ * btree splits. We may be converting the middle part of an unwritten
+ * extent and in this case we will insert two new extents in the btree
+ * each of which could cause a full split.
+ *
+ * This reservation amount will be used in the first call to
+ * xfs_bmbt_split() to select an AG with enough space to satisfy the
+ * rest of the operation.
+ */
resblks = XFS_DIOSTRAT_SPACE_RES(mp, 0) << 1;
do {
*ubused = error;
out_free:
- kmem_free(buf, sizeof(*buf));
+ kmem_free(buf);
return error;
}
/*
* Done, we're either out of filesystem or space to put the data.
*/
- kmem_free(irbuf, irbsize);
+ kmem_free(irbuf);
*ubcountp = ubelem;
/*
* Found some inodes, return them now and return the error next time.
}
*lastino = XFS_AGINO_TO_INO(mp, agno, agino);
}
- kmem_free(buffer, bcount * sizeof(*buffer));
+ kmem_free(buffer);
if (cur)
xfs_btree_del_cursor(cur, (error ? XFS_BTREE_ERROR :
XFS_BTREE_NOERROR));
static void
xlog_grant_add_space_write(struct log *log, int bytes)
{
- log->l_grant_write_bytes += bytes;
- if (log->l_grant_write_bytes > log->l_logsize) {
- log->l_grant_write_bytes -= log->l_logsize;
+ int tmp = log->l_logsize - log->l_grant_write_bytes;
+ if (tmp > bytes)
+ log->l_grant_write_bytes += bytes;
+ else {
log->l_grant_write_cycle++;
+ log->l_grant_write_bytes = bytes - tmp;
}
}
static void
xlog_grant_add_space_reserve(struct log *log, int bytes)
{
- log->l_grant_reserve_bytes += bytes;
- if (log->l_grant_reserve_bytes > log->l_logsize) {
- log->l_grant_reserve_bytes -= log->l_logsize;
+ int tmp = log->l_logsize - log->l_grant_reserve_bytes;
+ if (tmp > bytes)
+ log->l_grant_reserve_bytes += bytes;
+ else {
log->l_grant_reserve_cycle++;
+ log->l_grant_reserve_bytes = bytes - tmp;
}
}
spin_lock_init(&log->l_icloglock);
spin_lock_init(&log->l_grant_lock);
- initnsema(&log->l_flushsema, 0, "ic-flush");
+ sv_init(&log->l_flush_wait, 0, "flush_wait");
/* log record size must be multiple of BBSIZE; see xlog_rec_header_t */
ASSERT((XFS_BUF_SIZE(bp) & BBMASK) == 0);
}
#endif
next_iclog = iclog->ic_next;
- kmem_free(iclog, sizeof(xlog_in_core_t));
+ kmem_free(iclog);
iclog = next_iclog;
}
- freesema(&log->l_flushsema);
spinlock_destroy(&log->l_icloglock);
spinlock_destroy(&log->l_grant_lock);
}
#endif
log->l_mp->m_log = NULL;
- kmem_free(log, sizeof(xlog_t));
+ kmem_free(log);
} /* xlog_dealloc_log */
/*
int funcdidcallbacks; /* flag: function did callbacks */
int repeats; /* for issuing console warnings if
* looping too many times */
+ int wake = 0;
spin_lock(&log->l_icloglock);
first_iclog = iclog = log->l_iclog;
}
#endif
- flushcnt = 0;
- if (log->l_iclog->ic_state & (XLOG_STATE_ACTIVE|XLOG_STATE_IOERROR)) {
- flushcnt = log->l_flushcnt;
- log->l_flushcnt = 0;
- }
+ if (log->l_iclog->ic_state & (XLOG_STATE_ACTIVE|XLOG_STATE_IOERROR))
+ wake = 1;
spin_unlock(&log->l_icloglock);
- while (flushcnt--)
- vsema(&log->l_flushsema);
-} /* xlog_state_do_callback */
+
+ if (wake)
+ sv_broadcast(&log->l_flush_wait);
+}
/*
}
iclog = log->l_iclog;
- if (! (iclog->ic_state == XLOG_STATE_ACTIVE)) {
- log->l_flushcnt++;
- spin_unlock(&log->l_icloglock);
+ if (iclog->ic_state != XLOG_STATE_ACTIVE) {
xlog_trace_iclog(iclog, XLOG_TRACE_SLEEP_FLUSH);
XFS_STATS_INC(xs_log_noiclogs);
- /* Ensure that log writes happen */
- psema(&log->l_flushsema, PINOD);
+
+ /* Wait for log writes to have flushed */
+ sv_wait(&log->l_flush_wait, 0, &log->l_icloglock, 0);
goto restart;
}
- ASSERT(iclog->ic_state == XLOG_STATE_ACTIVE);
+
head = &iclog->ic_header;
atomic_inc(&iclog->ic_refcnt); /* prevents sync */
int l_logBBsize; /* size of log in BB chunks */
/* The following block of fields are changed while holding icloglock */
- sema_t l_flushsema ____cacheline_aligned_in_smp;
- /* iclog flushing semaphore */
- int l_flushcnt; /* # of procs waiting on this
- * sema */
+ sv_t l_flush_wait ____cacheline_aligned_in_smp;
+ /* waiting for iclog flush */
int l_covered_state;/* state of "covering disk
* log entries" */
xlog_in_core_t *l_iclog; /* head log queue */
} else {
prevp->bc_next = bcp->bc_next;
}
- kmem_free(bcp,
- sizeof(xfs_buf_cancel_t));
+ kmem_free(bcp);
}
}
return 1;
error:
if (need_free)
- kmem_free(in_f, sizeof(*in_f));
+ kmem_free(in_f);
return XFS_ERROR(error);
}
item = item->ri_next;
/* Free the regions in the item. */
for (i = 0; i < free_item->ri_cnt; i++) {
- kmem_free(free_item->ri_buf[i].i_addr,
- free_item->ri_buf[i].i_len);
+ kmem_free(free_item->ri_buf[i].i_addr);
}
/* Free the item itself */
- kmem_free(free_item->ri_buf,
- (free_item->ri_total * sizeof(xfs_log_iovec_t)));
- kmem_free(free_item, sizeof(xlog_recover_item_t));
+ kmem_free(free_item->ri_buf);
+ kmem_free(free_item);
} while (first_item != item);
/* Free the transaction recover structure */
- kmem_free(trans, sizeof(xlog_recover_t));
+ kmem_free(trans);
}
STATIC int
error = xlog_do_recovery_pass(log, head_blk, tail_blk,
XLOG_RECOVER_PASS1);
if (error != 0) {
- kmem_free(log->l_buf_cancel_table,
- XLOG_BC_TABLE_SIZE * sizeof(xfs_buf_cancel_t*));
+ kmem_free(log->l_buf_cancel_table);
log->l_buf_cancel_table = NULL;
return error;
}
}
#endif /* DEBUG */
- kmem_free(log->l_buf_cancel_table,
- XLOG_BC_TABLE_SIZE * sizeof(xfs_buf_cancel_t*));
+ kmem_free(log->l_buf_cancel_table);
log->l_buf_cancel_table = NULL;
return error;
STATIC int xfs_mount_log_sb(xfs_mount_t *, __int64_t);
STATIC int xfs_uuid_mount(xfs_mount_t *);
-STATIC void xfs_uuid_unmount(xfs_mount_t *mp);
STATIC void xfs_unmountfs_wait(xfs_mount_t *);
#ifdef HAVE_PERCPU_SB
-STATIC void xfs_icsb_destroy_counters(xfs_mount_t *);
STATIC void xfs_icsb_balance_counter(xfs_mount_t *, xfs_sb_field_t,
int);
STATIC void xfs_icsb_balance_counter_locked(xfs_mount_t *, xfs_sb_field_t,
#else
-#define xfs_icsb_destroy_counters(mp) do { } while (0)
#define xfs_icsb_balance_counter(mp, a, b) do { } while (0)
#define xfs_icsb_balance_counter_locked(mp, a, b) do { } while (0)
#define xfs_icsb_modify_counters(mp, a, b, c) do { } while (0)
{ sizeof(xfs_sb_t), 0 }
};
-/*
- * Return a pointer to an initialized xfs_mount structure.
- */
-xfs_mount_t *
-xfs_mount_init(void)
-{
- xfs_mount_t *mp;
-
- mp = kmem_zalloc(sizeof(xfs_mount_t), KM_SLEEP);
-
- if (xfs_icsb_init_counters(mp)) {
- mp->m_flags |= XFS_MOUNT_NO_PERCPU_SB;
- }
-
- spin_lock_init(&mp->m_sb_lock);
- mutex_init(&mp->m_ilock);
- mutex_init(&mp->m_growlock);
- atomic_set(&mp->m_active_trans, 0);
-
- return mp;
-}
-
/*
* Free up the resources associated with a mount structure. Assume that
* the structure was initially zeroed, so we can tell which fields got
* initialized.
*/
-void
+STATIC void
xfs_mount_free(
xfs_mount_t *mp)
{
for (agno = 0; agno < mp->m_maxagi; agno++)
if (mp->m_perag[agno].pagb_list)
- kmem_free(mp->m_perag[agno].pagb_list,
- sizeof(xfs_perag_busy_t) *
- XFS_PAGB_NUM_SLOTS);
- kmem_free(mp->m_perag,
- sizeof(xfs_perag_t) * mp->m_sb.sb_agcount);
+ kmem_free(mp->m_perag[agno].pagb_list);
+ kmem_free(mp->m_perag);
}
spinlock_destroy(&mp->m_ail_lock);
XFS_QM_DONE(mp);
if (mp->m_fsname != NULL)
- kmem_free(mp->m_fsname, mp->m_fsname_len);
+ kmem_free(mp->m_fsname);
if (mp->m_rtname != NULL)
- kmem_free(mp->m_rtname, strlen(mp->m_rtname) + 1);
+ kmem_free(mp->m_rtname);
if (mp->m_logname != NULL)
- kmem_free(mp->m_logname, strlen(mp->m_logname) + 1);
-
- xfs_icsb_destroy_counters(mp);
+ kmem_free(mp->m_logname);
}
/*
return XFS_ERROR(EFSCORRUPTED);
}
+ /*
+ * Until this is fixed only page-sized or smaller data blocks work.
+ */
+ if (unlikely(sbp->sb_blocksize > PAGE_SIZE)) {
+ xfs_fs_mount_cmn_err(flags,
+ "file system with blocksize %d bytes",
+ sbp->sb_blocksize);
+ xfs_fs_mount_cmn_err(flags,
+ "only pagesize (%ld) or less will currently work.",
+ PAGE_SIZE);
+ return XFS_ERROR(ENOSYS);
+ }
+
if (xfs_sb_validate_fsb_count(sbp, sbp->sb_dblocks) ||
xfs_sb_validate_fsb_count(sbp, sbp->sb_rblocks)) {
xfs_fs_mount_cmn_err(flags,
return XFS_ERROR(ENOSYS);
}
- /*
- * Until this is fixed only page-sized or smaller data blocks work.
- */
- if (unlikely(sbp->sb_blocksize > PAGE_SIZE)) {
- xfs_fs_mount_cmn_err(flags,
- "file system with blocksize %d bytes",
- sbp->sb_blocksize);
- xfs_fs_mount_cmn_err(flags,
- "only pagesize (%ld) or less will currently work.",
- PAGE_SIZE);
- return XFS_ERROR(ENOSYS);
- }
-
return 0;
}
* Re-check for ATTR2 in case it was found in bad_features2
* slot.
*/
- if (xfs_sb_version_hasattr2(&mp->m_sb))
+ if (xfs_sb_version_hasattr2(&mp->m_sb) &&
+ !(mp->m_flags & XFS_MOUNT_NOATTR2))
mp->m_flags |= XFS_MOUNT_ATTR2;
+ }
+
+ if (xfs_sb_version_hasattr2(&mp->m_sb) &&
+ (mp->m_flags & XFS_MOUNT_NOATTR2)) {
+ xfs_sb_version_removeattr2(&mp->m_sb);
+ update_flags |= XFS_SB_FEATURES2;
+ /* update sb_versionnum for the clearing of the morebits */
+ if (!sbp->sb_features2)
+ update_flags |= XFS_SB_VERSIONNUM;
}
/*
error2:
for (agno = 0; agno < sbp->sb_agcount; agno++)
if (mp->m_perag[agno].pagb_list)
- kmem_free(mp->m_perag[agno].pagb_list,
- sizeof(xfs_perag_busy_t) * XFS_PAGB_NUM_SLOTS);
- kmem_free(mp->m_perag, sbp->sb_agcount * sizeof(xfs_perag_t));
+ kmem_free(mp->m_perag[agno].pagb_list);
+ kmem_free(mp->m_perag);
mp->m_perag = NULL;
/* FALLTHROUGH */
error1:
if (uuid_mounted)
- xfs_uuid_unmount(mp);
- xfs_freesb(mp);
+ uuid_table_remove(&mp->m_sb.sb_uuid);
return error;
}
* log and makes sure that incore structures are freed.
*/
int
-xfs_unmountfs(xfs_mount_t *mp, struct cred *cr)
+xfs_unmountfs(xfs_mount_t *mp)
{
__uint64_t resblks;
int error = 0;
*/
ASSERT(mp->m_inodes == NULL);
- xfs_unmountfs_close(mp, cr);
if ((mp->m_flags & XFS_MOUNT_NOUUID) == 0)
- xfs_uuid_unmount(mp);
+ uuid_table_remove(&mp->m_sb.sb_uuid);
#if defined(DEBUG) || defined(INDUCE_IO_ERROR)
xfs_errortag_clearall(mp, 0);
return 0;
}
-void
-xfs_unmountfs_close(xfs_mount_t *mp, struct cred *cr)
-{
- if (mp->m_logdev_targp && mp->m_logdev_targp != mp->m_ddev_targp)
- xfs_free_buftarg(mp->m_logdev_targp, 1);
- if (mp->m_rtdev_targp)
- xfs_free_buftarg(mp->m_rtdev_targp, 1);
- xfs_free_buftarg(mp->m_ddev_targp, 0);
-}
-
STATIC void
xfs_unmountfs_wait(xfs_mount_t *mp)
{
return 0;
}
-/*
- * Remove filesystem from the UUID table.
- */
-STATIC void
-xfs_uuid_unmount(
- xfs_mount_t *mp)
-{
- uuid_table_remove(&mp->m_sb.sb_uuid);
-}
-
/*
* Used to log changes to the superblock unit and width fields which could
* be altered by the mount options, as well as any potential sb_features2
int error;
ASSERT(fields & (XFS_SB_UNIT | XFS_SB_WIDTH | XFS_SB_UUID |
- XFS_SB_FEATURES2 | XFS_SB_BAD_FEATURES2));
+ XFS_SB_FEATURES2 | XFS_SB_BAD_FEATURES2 |
+ XFS_SB_VERSIONNUM));
tp = xfs_trans_alloc(mp, XFS_TRANS_SB_UNIT);
error = xfs_trans_reserve(tp, 0, mp->m_sb.sb_sectsize + 128, 0, 0,
xfs_icsb_unlock(mp);
}
-STATIC void
+void
xfs_icsb_destroy_counters(
xfs_mount_t *mp)
{
struct xfs_extdelta;
struct xfs_swapext;
struct xfs_mru_cache;
+struct xfs_nameops;
/*
* Prototypes and functions for the Data Migration subsystem.
extern int xfs_icsb_init_counters(struct xfs_mount *);
extern void xfs_icsb_reinit_counters(struct xfs_mount *);
+extern void xfs_icsb_destroy_counters(struct xfs_mount *);
extern void xfs_icsb_sync_counters(struct xfs_mount *, int);
extern void xfs_icsb_sync_counters_locked(struct xfs_mount *, int);
#else
-#define xfs_icsb_init_counters(mp) (0)
-#define xfs_icsb_reinit_counters(mp) do { } while (0)
+#define xfs_icsb_init_counters(mp) (0)
+#define xfs_icsb_destroy_counters(mp) do { } while (0)
+#define xfs_icsb_reinit_counters(mp) do { } while (0)
#define xfs_icsb_sync_counters(mp, flags) do { } while (0)
#define xfs_icsb_sync_counters_locked(mp, flags) do { } while (0)
#endif
__uint8_t m_inode_quiesce;/* call quiesce on new inodes.
field governed by m_ilock */
__uint8_t m_sectbb_log; /* sectlog - BBSHIFT */
+ const struct xfs_nameops *m_dirnameops; /* vector of dir name ops */
int m_dirblksize; /* directory block sz--bytes */
int m_dirblkfsbs; /* directory block sz--fsbs */
xfs_dablk_t m_dirdatablk; /* blockno of dir data v2 */
counters */
#define XFS_MOUNT_FILESTREAMS (1ULL << 24) /* enable the filestreams
allocator */
+#define XFS_MOUNT_NOATTR2 (1ULL << 25) /* disable use of attr2 format */
/*
#define XFS_MOUNT_ILOCK(mp) mutex_lock(&((mp)->m_ilock))
#define XFS_MOUNT_IUNLOCK(mp) mutex_unlock(&((mp)->m_ilock))
-extern xfs_mount_t *xfs_mount_init(void);
extern void xfs_mod_sb(xfs_trans_t *, __int64_t);
extern int xfs_log_sbcount(xfs_mount_t *, uint);
-extern void xfs_mount_free(xfs_mount_t *mp);
extern int xfs_mountfs(xfs_mount_t *mp, int);
extern void xfs_mountfs_check_barriers(xfs_mount_t *mp);
-extern int xfs_unmountfs(xfs_mount_t *, struct cred *);
-extern void xfs_unmountfs_close(xfs_mount_t *, struct cred *);
+extern int xfs_unmountfs(xfs_mount_t *);
extern int xfs_unmountfs_writesb(xfs_mount_t *);
extern int xfs_unmount_flush(xfs_mount_t *, int);
extern int xfs_mod_incore_sb(xfs_mount_t *, xfs_sb_field_t, int64_t, int);
extern struct xfs_dmops xfs_dmcore_xfs;
-extern int xfs_init(void);
-extern void xfs_cleanup(void);
-
#endif /* __KERNEL__ */
#endif /* __XFS_MOUNT_H__ */
xfs_mru_elem_zone = kmem_zone_init(sizeof(xfs_mru_cache_elem_t),
"xfs_mru_cache_elem");
if (!xfs_mru_elem_zone)
- return ENOMEM;
+ goto out;
xfs_mru_reap_wq = create_singlethread_workqueue("xfs_mru_cache");
- if (!xfs_mru_reap_wq) {
- kmem_zone_destroy(xfs_mru_elem_zone);
- return ENOMEM;
- }
+ if (!xfs_mru_reap_wq)
+ goto out_destroy_mru_elem_zone;
return 0;
+
+ out_destroy_mru_elem_zone:
+ kmem_zone_destroy(xfs_mru_elem_zone);
+ out:
+ return -ENOMEM;
}
void
exit:
if (err && mru && mru->lists)
- kmem_free(mru->lists, mru->grp_count * sizeof(*mru->lists));
+ kmem_free(mru->lists);
if (err && mru)
- kmem_free(mru, sizeof(*mru));
+ kmem_free(mru);
return err;
}
xfs_mru_cache_flush(mru);
- kmem_free(mru->lists, mru->grp_count * sizeof(*mru->lists));
- kmem_free(mru, sizeof(*mru));
+ kmem_free(mru->lists);
+ kmem_free(mru);
}
/*
ASSERT(error != EEXIST);
if (error)
goto abort_return;
- xfs_ichgtime(src_ip, XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG);
-
- } else {
- /*
- * We always want to hit the ctime on the source inode.
- * We do it in the if clause above for the 'new_parent &&
- * src_is_directory' case, and here we get all the other
- * cases. This isn't strictly required by the standards
- * since the source inode isn't really being changed,
- * but old unix file systems did it and some incremental
- * backup programs won't work without it.
- */
- xfs_ichgtime(src_ip, XFS_ICHGTIME_CHG);
}
+ /*
+ * We always want to hit the ctime on the source inode.
+ *
+ * This isn't strictly required by the standards since the source
+ * inode isn't really being changed, but old unix file systems did
+ * it and some incremental backup programs won't work without it.
+ */
+ xfs_ichgtime(src_ip, XFS_ICHGTIME_CHG);
+
/*
* Adjust the link count on src_dp. This is necessary when
* renaming a directory, either within one parent when
/*
* Free the fake mp structure.
*/
- kmem_free(nmp, sizeof(*nmp));
+ kmem_free(nmp);
return error;
}
#define XFS_SB_VERSION_SECTORBIT 0x0800
#define XFS_SB_VERSION_EXTFLGBIT 0x1000
#define XFS_SB_VERSION_DIRV2BIT 0x2000
+#define XFS_SB_VERSION_BORGBIT 0x4000 /* ASCII only case-insens. */
#define XFS_SB_VERSION_MOREBITSBIT 0x8000
#define XFS_SB_VERSION_OKSASHFBITS \
(XFS_SB_VERSION_EXTFLGBIT | \
- XFS_SB_VERSION_DIRV2BIT)
+ XFS_SB_VERSION_DIRV2BIT | \
+ XFS_SB_VERSION_BORGBIT)
#define XFS_SB_VERSION_OKREALFBITS \
(XFS_SB_VERSION_ATTRBIT | \
XFS_SB_VERSION_NLINKBIT | \
((sbp)->sb_versionnum & XFS_SB_VERSION_SECTORBIT);
}
+static inline int xfs_sb_version_hasasciici(xfs_sb_t *sbp)
+{
+ return (XFS_SB_VERSION_NUM(sbp) == XFS_SB_VERSION_4) && \
+ (sbp->sb_versionnum & XFS_SB_VERSION_BORGBIT);
+}
+
static inline int xfs_sb_version_hasmorebits(xfs_sb_t *sbp)
{
return (XFS_SB_VERSION_NUM(sbp) == XFS_SB_VERSION_4) && \
((sbp)->sb_features2 | XFS_SB_VERSION2_ATTR2BIT)));
}
+static inline void xfs_sb_version_removeattr2(xfs_sb_t *sbp)
+{
+ sbp->sb_features2 &= ~XFS_SB_VERSION2_ATTR2BIT;
+ if (!sbp->sb_features2)
+ sbp->sb_versionnum &= ~XFS_SB_VERSION_MOREBITSBIT;
+}
+
/*
* end of superblock version macros
*/
tp->t_commit_lsn = commit_lsn;
if (nvec > XFS_TRANS_LOGVEC_COUNT) {
- kmem_free(log_vector, nvec * sizeof(xfs_log_iovec_t));
+ kmem_free(log_vector);
}
/*
ASSERT(!XFS_LIC_ARE_ALL_FREE(licp));
xfs_trans_chunk_committed(licp, tp->t_lsn, abortflag);
next_licp = licp->lic_next;
- kmem_free(licp, sizeof(xfs_log_item_chunk_t));
+ kmem_free(licp);
licp = next_licp;
}
iip = ip->i_itemp;
if (iip->ili_root_size != 0) {
ASSERT(iip->ili_orig_root != NULL);
- kmem_free(iip->ili_orig_root, iip->ili_root_size);
+ kmem_free(iip->ili_orig_root);
iip->ili_root_size = 0;
iip->ili_orig_root = NULL;
}
licpp = &((*licpp)->lic_next);
}
*licpp = licp->lic_next;
- kmem_free(licp, sizeof(xfs_log_item_chunk_t));
+ kmem_free(licp);
tp->t_items_free -= XFS_LIC_NUM_SLOTS;
}
}
ASSERT(!XFS_LIC_ARE_ALL_FREE(licp));
(void) xfs_trans_unlock_chunk(licp, 1, abort, NULLCOMMITLSN);
next_licp = licp->lic_next;
- kmem_free(licp, sizeof(xfs_log_item_chunk_t));
+ kmem_free(licp);
licp = next_licp;
}
next_licp = licp->lic_next;
if (XFS_LIC_ARE_ALL_FREE(licp)) {
*licpp = next_licp;
- kmem_free(licp, sizeof(xfs_log_item_chunk_t));
+ kmem_free(licp);
freed -= XFS_LIC_NUM_SLOTS;
} else {
licpp = &(licp->lic_next);
lbcp = tp->t_busy.lbc_next;
while (lbcp != NULL) {
lbcq = lbcp->lbc_next;
- kmem_free(lbcp, sizeof(xfs_log_busy_chunk_t));
+ kmem_free(lbcp);
lbcp = lbcq;
}
#include "xfs_utils.h"
-int __init
-xfs_init(void)
-{
-#ifdef XFS_DABUF_DEBUG
- extern spinlock_t xfs_dabuf_global_lock;
- spin_lock_init(&xfs_dabuf_global_lock);
-#endif
-
- /*
- * Initialize all of the zone allocators we use.
- */
- xfs_log_ticket_zone = kmem_zone_init(sizeof(xlog_ticket_t),
- "xfs_log_ticket");
- xfs_bmap_free_item_zone = kmem_zone_init(sizeof(xfs_bmap_free_item_t),
- "xfs_bmap_free_item");
- xfs_btree_cur_zone = kmem_zone_init(sizeof(xfs_btree_cur_t),
- "xfs_btree_cur");
- xfs_da_state_zone = kmem_zone_init(sizeof(xfs_da_state_t),
- "xfs_da_state");
- xfs_dabuf_zone = kmem_zone_init(sizeof(xfs_dabuf_t), "xfs_dabuf");
- xfs_ifork_zone = kmem_zone_init(sizeof(xfs_ifork_t), "xfs_ifork");
- xfs_trans_zone = kmem_zone_init(sizeof(xfs_trans_t), "xfs_trans");
- xfs_acl_zone_init(xfs_acl_zone, "xfs_acl");
- xfs_mru_cache_init();
- xfs_filestream_init();
-
- /*
- * The size of the zone allocated buf log item is the maximum
- * size possible under XFS. This wastes a little bit of memory,
- * but it is much faster.
- */
- xfs_buf_item_zone =
- kmem_zone_init((sizeof(xfs_buf_log_item_t) +
- (((XFS_MAX_BLOCKSIZE / XFS_BLI_CHUNK) /
- NBWORD) * sizeof(int))),
- "xfs_buf_item");
- xfs_efd_zone =
- kmem_zone_init((sizeof(xfs_efd_log_item_t) +
- ((XFS_EFD_MAX_FAST_EXTENTS - 1) *
- sizeof(xfs_extent_t))),
- "xfs_efd_item");
- xfs_efi_zone =
- kmem_zone_init((sizeof(xfs_efi_log_item_t) +
- ((XFS_EFI_MAX_FAST_EXTENTS - 1) *
- sizeof(xfs_extent_t))),
- "xfs_efi_item");
-
- /*
- * These zones warrant special memory allocator hints
- */
- xfs_inode_zone =
- kmem_zone_init_flags(sizeof(xfs_inode_t), "xfs_inode",
- KM_ZONE_HWALIGN | KM_ZONE_RECLAIM |
- KM_ZONE_SPREAD, NULL);
- xfs_ili_zone =
- kmem_zone_init_flags(sizeof(xfs_inode_log_item_t), "xfs_ili",
- KM_ZONE_SPREAD, NULL);
-
- /*
- * Allocate global trace buffers.
- */
-#ifdef XFS_ALLOC_TRACE
- xfs_alloc_trace_buf = ktrace_alloc(XFS_ALLOC_TRACE_SIZE, KM_SLEEP);
-#endif
-#ifdef XFS_BMAP_TRACE
- xfs_bmap_trace_buf = ktrace_alloc(XFS_BMAP_TRACE_SIZE, KM_SLEEP);
-#endif
-#ifdef XFS_BMBT_TRACE
- xfs_bmbt_trace_buf = ktrace_alloc(XFS_BMBT_TRACE_SIZE, KM_SLEEP);
-#endif
-#ifdef XFS_ATTR_TRACE
- xfs_attr_trace_buf = ktrace_alloc(XFS_ATTR_TRACE_SIZE, KM_SLEEP);
-#endif
-#ifdef XFS_DIR2_TRACE
- xfs_dir2_trace_buf = ktrace_alloc(XFS_DIR2_GTRACE_SIZE, KM_SLEEP);
-#endif
-
- xfs_dir_startup();
-
-#if (defined(DEBUG) || defined(INDUCE_IO_ERROR))
- xfs_error_test_init();
-#endif /* DEBUG || INDUCE_IO_ERROR */
-
- xfs_init_procfs();
- xfs_sysctl_register();
- return 0;
-}
-
-void __exit
-xfs_cleanup(void)
-{
- extern kmem_zone_t *xfs_inode_zone;
- extern kmem_zone_t *xfs_efd_zone;
- extern kmem_zone_t *xfs_efi_zone;
-
- xfs_cleanup_procfs();
- xfs_sysctl_unregister();
- xfs_filestream_uninit();
- xfs_mru_cache_uninit();
- xfs_acl_zone_destroy(xfs_acl_zone);
-
-#ifdef XFS_DIR2_TRACE
- ktrace_free(xfs_dir2_trace_buf);
-#endif
-#ifdef XFS_ATTR_TRACE
- ktrace_free(xfs_attr_trace_buf);
-#endif
-#ifdef XFS_BMBT_TRACE
- ktrace_free(xfs_bmbt_trace_buf);
-#endif
-#ifdef XFS_BMAP_TRACE
- ktrace_free(xfs_bmap_trace_buf);
-#endif
-#ifdef XFS_ALLOC_TRACE
- ktrace_free(xfs_alloc_trace_buf);
-#endif
-
- kmem_zone_destroy(xfs_bmap_free_item_zone);
- kmem_zone_destroy(xfs_btree_cur_zone);
- kmem_zone_destroy(xfs_inode_zone);
- kmem_zone_destroy(xfs_trans_zone);
- kmem_zone_destroy(xfs_da_state_zone);
- kmem_zone_destroy(xfs_dabuf_zone);
- kmem_zone_destroy(xfs_buf_item_zone);
- kmem_zone_destroy(xfs_efd_zone);
- kmem_zone_destroy(xfs_efi_zone);
- kmem_zone_destroy(xfs_ifork_zone);
- kmem_zone_destroy(xfs_ili_zone);
- kmem_zone_destroy(xfs_log_ticket_zone);
-}
-
-/*
- * xfs_start_flags
- *
- * This function fills in xfs_mount_t fields based on mount args.
- * Note: the superblock has _not_ yet been read in.
- */
-STATIC int
-xfs_start_flags(
- struct xfs_mount_args *ap,
- struct xfs_mount *mp)
-{
- /* Values are in BBs */
- if ((ap->flags & XFSMNT_NOALIGN) != XFSMNT_NOALIGN) {
- /*
- * At this point the superblock has not been read
- * in, therefore we do not know the block size.
- * Before the mount call ends we will convert
- * these to FSBs.
- */
- mp->m_dalign = ap->sunit;
- mp->m_swidth = ap->swidth;
- }
-
- if (ap->logbufs != -1 &&
- ap->logbufs != 0 &&
- (ap->logbufs < XLOG_MIN_ICLOGS ||
- ap->logbufs > XLOG_MAX_ICLOGS)) {
- cmn_err(CE_WARN,
- "XFS: invalid logbufs value: %d [not %d-%d]",
- ap->logbufs, XLOG_MIN_ICLOGS, XLOG_MAX_ICLOGS);
- return XFS_ERROR(EINVAL);
- }
- mp->m_logbufs = ap->logbufs;
- if (ap->logbufsize != -1 &&
- ap->logbufsize != 0 &&
- (ap->logbufsize < XLOG_MIN_RECORD_BSIZE ||
- ap->logbufsize > XLOG_MAX_RECORD_BSIZE ||
- !is_power_of_2(ap->logbufsize))) {
- cmn_err(CE_WARN,
- "XFS: invalid logbufsize: %d [not 16k,32k,64k,128k or 256k]",
- ap->logbufsize);
- return XFS_ERROR(EINVAL);
- }
- mp->m_logbsize = ap->logbufsize;
- mp->m_fsname_len = strlen(ap->fsname) + 1;
- mp->m_fsname = kmem_alloc(mp->m_fsname_len, KM_SLEEP);
- strcpy(mp->m_fsname, ap->fsname);
- if (ap->rtname[0]) {
- mp->m_rtname = kmem_alloc(strlen(ap->rtname) + 1, KM_SLEEP);
- strcpy(mp->m_rtname, ap->rtname);
- }
- if (ap->logname[0]) {
- mp->m_logname = kmem_alloc(strlen(ap->logname) + 1, KM_SLEEP);
- strcpy(mp->m_logname, ap->logname);
- }
-
- if (ap->flags & XFSMNT_WSYNC)
- mp->m_flags |= XFS_MOUNT_WSYNC;
-#if XFS_BIG_INUMS
- if (ap->flags & XFSMNT_INO64) {
- mp->m_flags |= XFS_MOUNT_INO64;
- mp->m_inoadd = XFS_INO64_OFFSET;
- }
-#endif
- if (ap->flags & XFSMNT_RETERR)
- mp->m_flags |= XFS_MOUNT_RETERR;
- if (ap->flags & XFSMNT_NOALIGN)
- mp->m_flags |= XFS_MOUNT_NOALIGN;
- if (ap->flags & XFSMNT_SWALLOC)
- mp->m_flags |= XFS_MOUNT_SWALLOC;
- if (ap->flags & XFSMNT_OSYNCISOSYNC)
- mp->m_flags |= XFS_MOUNT_OSYNCISOSYNC;
- if (ap->flags & XFSMNT_32BITINODES)
- mp->m_flags |= XFS_MOUNT_32BITINODES;
-
- if (ap->flags & XFSMNT_IOSIZE) {
- if (ap->iosizelog > XFS_MAX_IO_LOG ||
- ap->iosizelog < XFS_MIN_IO_LOG) {
- cmn_err(CE_WARN,
- "XFS: invalid log iosize: %d [not %d-%d]",
- ap->iosizelog, XFS_MIN_IO_LOG,
- XFS_MAX_IO_LOG);
- return XFS_ERROR(EINVAL);
- }
-
- mp->m_flags |= XFS_MOUNT_DFLT_IOSIZE;
- mp->m_readio_log = mp->m_writeio_log = ap->iosizelog;
- }
-
- if (ap->flags & XFSMNT_IKEEP)
- mp->m_flags |= XFS_MOUNT_IKEEP;
- if (ap->flags & XFSMNT_DIRSYNC)
- mp->m_flags |= XFS_MOUNT_DIRSYNC;
- if (ap->flags & XFSMNT_ATTR2)
- mp->m_flags |= XFS_MOUNT_ATTR2;
-
- if (ap->flags2 & XFSMNT2_COMPAT_IOSIZE)
- mp->m_flags |= XFS_MOUNT_COMPAT_IOSIZE;
-
- /*
- * no recovery flag requires a read-only mount
- */
- if (ap->flags & XFSMNT_NORECOVERY) {
- if (!(mp->m_flags & XFS_MOUNT_RDONLY)) {
- cmn_err(CE_WARN,
- "XFS: tried to mount a FS read-write without recovery!");
- return XFS_ERROR(EINVAL);
- }
- mp->m_flags |= XFS_MOUNT_NORECOVERY;
- }
-
- if (ap->flags & XFSMNT_NOUUID)
- mp->m_flags |= XFS_MOUNT_NOUUID;
- if (ap->flags & XFSMNT_BARRIER)
- mp->m_flags |= XFS_MOUNT_BARRIER;
- else
- mp->m_flags &= ~XFS_MOUNT_BARRIER;
-
- if (ap->flags2 & XFSMNT2_FILESTREAMS)
- mp->m_flags |= XFS_MOUNT_FILESTREAMS;
-
- if (ap->flags & XFSMNT_DMAPI)
- mp->m_flags |= XFS_MOUNT_DMAPI;
- return 0;
-}
-
-/*
- * This function fills in xfs_mount_t fields based on mount args.
- * Note: the superblock _has_ now been read in.
- */
-STATIC int
-xfs_finish_flags(
- struct xfs_mount_args *ap,
- struct xfs_mount *mp)
-{
- int ronly = (mp->m_flags & XFS_MOUNT_RDONLY);
-
- /* Fail a mount where the logbuf is smaller then the log stripe */
- if (xfs_sb_version_haslogv2(&mp->m_sb)) {
- if ((ap->logbufsize <= 0) &&
- (mp->m_sb.sb_logsunit > XLOG_BIG_RECORD_BSIZE)) {
- mp->m_logbsize = mp->m_sb.sb_logsunit;
- } else if (ap->logbufsize > 0 &&
- ap->logbufsize < mp->m_sb.sb_logsunit) {
- cmn_err(CE_WARN,
- "XFS: logbuf size must be greater than or equal to log stripe size");
- return XFS_ERROR(EINVAL);
- }
- } else {
- /* Fail a mount if the logbuf is larger than 32K */
- if (ap->logbufsize > XLOG_BIG_RECORD_BSIZE) {
- cmn_err(CE_WARN,
- "XFS: logbuf size for version 1 logs must be 16K or 32K");
- return XFS_ERROR(EINVAL);
- }
- }
-
- if (xfs_sb_version_hasattr2(&mp->m_sb))
- mp->m_flags |= XFS_MOUNT_ATTR2;
-
- /*
- * prohibit r/w mounts of read-only filesystems
- */
- if ((mp->m_sb.sb_flags & XFS_SBF_READONLY) && !ronly) {
- cmn_err(CE_WARN,
- "XFS: cannot mount a read-only filesystem as read-write");
- return XFS_ERROR(EROFS);
- }
-
- /*
- * check for shared mount.
- */
- if (ap->flags & XFSMNT_SHARED) {
- if (!xfs_sb_version_hasshared(&mp->m_sb))
- return XFS_ERROR(EINVAL);
-
- /*
- * For IRIX 6.5, shared mounts must have the shared
- * version bit set, have the persistent readonly
- * field set, must be version 0 and can only be mounted
- * read-only.
- */
- if (!ronly || !(mp->m_sb.sb_flags & XFS_SBF_READONLY) ||
- (mp->m_sb.sb_shared_vn != 0))
- return XFS_ERROR(EINVAL);
-
- mp->m_flags |= XFS_MOUNT_SHARED;
-
- /*
- * Shared XFS V0 can't deal with DMI. Return EINVAL.
- */
- if (mp->m_sb.sb_shared_vn == 0 && (ap->flags & XFSMNT_DMAPI))
- return XFS_ERROR(EINVAL);
- }
-
- if (ap->flags & XFSMNT_UQUOTA) {
- mp->m_qflags |= (XFS_UQUOTA_ACCT | XFS_UQUOTA_ACTIVE);
- if (ap->flags & XFSMNT_UQUOTAENF)
- mp->m_qflags |= XFS_UQUOTA_ENFD;
- }
-
- if (ap->flags & XFSMNT_GQUOTA) {
- mp->m_qflags |= (XFS_GQUOTA_ACCT | XFS_GQUOTA_ACTIVE);
- if (ap->flags & XFSMNT_GQUOTAENF)
- mp->m_qflags |= XFS_OQUOTA_ENFD;
- } else if (ap->flags & XFSMNT_PQUOTA) {
- mp->m_qflags |= (XFS_PQUOTA_ACCT | XFS_PQUOTA_ACTIVE);
- if (ap->flags & XFSMNT_PQUOTAENF)
- mp->m_qflags |= XFS_OQUOTA_ENFD;
- }
-
- return 0;
-}
-
-/*
- * xfs_mount
- *
- * The file system configurations are:
- * (1) device (partition) with data and internal log
- * (2) logical volume with data and log subvolumes.
- * (3) logical volume with data, log, and realtime subvolumes.
- *
- * We only have to handle opening the log and realtime volumes here if
- * they are present. The data subvolume has already been opened by
- * get_sb_bdev() and is stored in vfsp->vfs_super->s_bdev.
- */
-int
-xfs_mount(
- struct xfs_mount *mp,
- struct xfs_mount_args *args,
- cred_t *credp)
-{
- struct block_device *ddev, *logdev, *rtdev;
- int flags = 0, error;
-
- ddev = mp->m_super->s_bdev;
- logdev = rtdev = NULL;
-
- error = xfs_dmops_get(mp, args);
- if (error)
- return error;
- error = xfs_qmops_get(mp, args);
- if (error)
- return error;
-
- if (args->flags & XFSMNT_QUIET)
- flags |= XFS_MFSI_QUIET;
-
- /*
- * Open real time and log devices - order is important.
- */
- if (args->logname[0]) {
- error = xfs_blkdev_get(mp, args->logname, &logdev);
- if (error)
- return error;
- }
- if (args->rtname[0]) {
- error = xfs_blkdev_get(mp, args->rtname, &rtdev);
- if (error) {
- xfs_blkdev_put(logdev);
- return error;
- }
-
- if (rtdev == ddev || rtdev == logdev) {
- cmn_err(CE_WARN,
- "XFS: Cannot mount filesystem with identical rtdev and ddev/logdev.");
- xfs_blkdev_put(logdev);
- xfs_blkdev_put(rtdev);
- return EINVAL;
- }
- }
-
- /*
- * Setup xfs_mount buffer target pointers
- */
- error = ENOMEM;
- mp->m_ddev_targp = xfs_alloc_buftarg(ddev, 0);
- if (!mp->m_ddev_targp) {
- xfs_blkdev_put(logdev);
- xfs_blkdev_put(rtdev);
- return error;
- }
- if (rtdev) {
- mp->m_rtdev_targp = xfs_alloc_buftarg(rtdev, 1);
- if (!mp->m_rtdev_targp) {
- xfs_blkdev_put(logdev);
- xfs_blkdev_put(rtdev);
- goto error0;
- }
- }
- mp->m_logdev_targp = (logdev && logdev != ddev) ?
- xfs_alloc_buftarg(logdev, 1) : mp->m_ddev_targp;
- if (!mp->m_logdev_targp) {
- xfs_blkdev_put(logdev);
- xfs_blkdev_put(rtdev);
- goto error0;
- }
-
- /*
- * Setup flags based on mount(2) options and then the superblock
- */
- error = xfs_start_flags(args, mp);
- if (error)
- goto error1;
- error = xfs_readsb(mp, flags);
- if (error)
- goto error1;
- error = xfs_finish_flags(args, mp);
- if (error)
- goto error2;
-
- /*
- * Setup xfs_mount buffer target pointers based on superblock
- */
- error = xfs_setsize_buftarg(mp->m_ddev_targp, mp->m_sb.sb_blocksize,
- mp->m_sb.sb_sectsize);
- if (!error && logdev && logdev != ddev) {
- unsigned int log_sector_size = BBSIZE;
-
- if (xfs_sb_version_hassector(&mp->m_sb))
- log_sector_size = mp->m_sb.sb_logsectsize;
- error = xfs_setsize_buftarg(mp->m_logdev_targp,
- mp->m_sb.sb_blocksize,
- log_sector_size);
- }
- if (!error && rtdev)
- error = xfs_setsize_buftarg(mp->m_rtdev_targp,
- mp->m_sb.sb_blocksize,
- mp->m_sb.sb_sectsize);
- if (error)
- goto error2;
-
- if (mp->m_flags & XFS_MOUNT_BARRIER)
- xfs_mountfs_check_barriers(mp);
-
- if ((error = xfs_filestream_mount(mp)))
- goto error2;
-
- error = xfs_mountfs(mp, flags);
- if (error)
- goto error2;
-
- XFS_SEND_MOUNT(mp, DM_RIGHT_NULL, args->mtpt, args->fsname);
-
- return 0;
-
-error2:
- if (mp->m_sb_bp)
- xfs_freesb(mp);
-error1:
- xfs_binval(mp->m_ddev_targp);
- if (logdev && logdev != ddev)
- xfs_binval(mp->m_logdev_targp);
- if (rtdev)
- xfs_binval(mp->m_rtdev_targp);
-error0:
- xfs_unmountfs_close(mp, credp);
- xfs_qmops_put(mp);
- xfs_dmops_put(mp);
- return error;
-}
-
-int
-xfs_unmount(
- xfs_mount_t *mp,
- int flags,
- cred_t *credp)
-{
- xfs_inode_t *rip;
- bhv_vnode_t *rvp;
- int unmount_event_wanted = 0;
- int unmount_event_flags = 0;
- int xfs_unmountfs_needed = 0;
- int error;
-
- rip = mp->m_rootip;
- rvp = XFS_ITOV(rip);
-
-#ifdef HAVE_DMAPI
- if (mp->m_flags & XFS_MOUNT_DMAPI) {
- error = XFS_SEND_PREUNMOUNT(mp,
- rip, DM_RIGHT_NULL, rip, DM_RIGHT_NULL,
- NULL, NULL, 0, 0,
- (mp->m_dmevmask & (1<<DM_EVENT_PREUNMOUNT))?
- 0:DM_FLAGS_UNWANTED);
- if (error)
- return XFS_ERROR(error);
- unmount_event_wanted = 1;
- unmount_event_flags = (mp->m_dmevmask & (1<<DM_EVENT_UNMOUNT))?
- 0 : DM_FLAGS_UNWANTED;
- }
-#endif
-
- /*
- * Blow away any referenced inode in the filestreams cache.
- * This can and will cause log traffic as inodes go inactive
- * here.
- */
- xfs_filestream_unmount(mp);
-
- XFS_bflush(mp->m_ddev_targp);
- error = xfs_unmount_flush(mp, 0);
- if (error)
- goto out;
-
- ASSERT(vn_count(rvp) == 1);
-
- /*
- * Drop the reference count
- */
- IRELE(rip);
-
- /*
- * If we're forcing a shutdown, typically because of a media error,
- * we want to make sure we invalidate dirty pages that belong to
- * referenced vnodes as well.
- */
- if (XFS_FORCED_SHUTDOWN(mp)) {
- error = xfs_sync(mp, SYNC_WAIT | SYNC_CLOSE);
- ASSERT(error != EFSCORRUPTED);
- }
- xfs_unmountfs_needed = 1;
-
-out:
- /* Send DMAPI event, if required.
- * Then do xfs_unmountfs() if needed.
- * Then return error (or zero).
- */
- if (unmount_event_wanted) {
- /* Note: mp structure must still exist for
- * XFS_SEND_UNMOUNT() call.
- */
- XFS_SEND_UNMOUNT(mp, error == 0 ? rip : NULL,
- DM_RIGHT_NULL, 0, error, unmount_event_flags);
- }
- if (xfs_unmountfs_needed) {
- /*
- * Call common unmount function to flush to disk
- * and free the super block buffer & mount structures.
- */
- xfs_unmountfs(mp, credp);
- xfs_qmops_put(mp);
- xfs_dmops_put(mp);
- kmem_free(mp, sizeof(xfs_mount_t));
- }
-
- return XFS_ERROR(error);
-}
-
STATIC void
xfs_quiesce_fs(
xfs_mount_t *mp)
xfs_unmountfs_writesb(mp);
}
-int
-xfs_mntupdate(
- struct xfs_mount *mp,
- int *flags,
- struct xfs_mount_args *args)
-{
- if (!(*flags & MS_RDONLY)) { /* rw/ro -> rw */
- if (mp->m_flags & XFS_MOUNT_RDONLY)
- mp->m_flags &= ~XFS_MOUNT_RDONLY;
- if (args->flags & XFSMNT_BARRIER) {
- mp->m_flags |= XFS_MOUNT_BARRIER;
- xfs_mountfs_check_barriers(mp);
- } else {
- mp->m_flags &= ~XFS_MOUNT_BARRIER;
- }
- } else if (!(mp->m_flags & XFS_MOUNT_RDONLY)) { /* rw -> ro */
- xfs_filestream_flush(mp);
- xfs_sync(mp, SYNC_DATA_QUIESCE);
- xfs_attr_quiesce(mp);
- mp->m_flags |= XFS_MOUNT_RDONLY;
- }
- return 0;
-}
-
/*
* xfs_unmount_flush implements a set of flush operation on special
* inodes, which are needed as a separate set of operations so that
if (XFS_FORCED_SHUTDOWN(mp) && !(flags & SYNC_CLOSE)) {
XFS_MOUNT_IUNLOCK(mp);
- kmem_free(ipointer, sizeof(xfs_iptr_t));
+ kmem_free(ipointer);
return 0;
}
}
XFS_MOUNT_IUNLOCK(mp);
ASSERT(ipointer_in == B_FALSE);
- kmem_free(ipointer, sizeof(xfs_iptr_t));
+ kmem_free(ipointer);
return XFS_ERROR(error);
}
ASSERT(ipointer_in == B_FALSE);
- kmem_free(ipointer, sizeof(xfs_iptr_t));
+ kmem_free(ipointer);
return XFS_ERROR(last_error);
}
struct xfs_mount;
struct xfs_mount_args;
-int xfs_mount(struct xfs_mount *mp, struct xfs_mount_args *args,
- struct cred *credp);
-int xfs_unmount(struct xfs_mount *mp, int flags, struct cred *credp);
-int xfs_mntupdate(struct xfs_mount *mp, int *flags,
- struct xfs_mount_args *args);
int xfs_sync(struct xfs_mount *mp, int flags);
void xfs_do_force_shutdown(struct xfs_mount *mp, int flags, char *fname,
int lnnum);
return 0;
}
-/*
- * xfs_setattr
- */
int
xfs_setattr(
- xfs_inode_t *ip,
- bhv_vattr_t *vap,
+ struct xfs_inode *ip,
+ struct iattr *iattr,
int flags,
cred_t *credp)
{
xfs_mount_t *mp = ip->i_mount;
+ struct inode *inode = XFS_ITOV(ip);
+ int mask = iattr->ia_valid;
xfs_trans_t *tp;
- int mask;
int code;
uint lock_flags;
uint commit_flags=0;
uid_t uid=0, iuid=0;
gid_t gid=0, igid=0;
int timeflags = 0;
- xfs_prid_t projid=0, iprojid=0;
struct xfs_dquot *udqp, *gdqp, *olddquot1, *olddquot2;
int file_owner;
int need_iolock = 1;
if (mp->m_flags & XFS_MOUNT_RDONLY)
return XFS_ERROR(EROFS);
- /*
- * Cannot set certain attributes.
- */
- mask = vap->va_mask;
- if (mask & XFS_AT_NOSET) {
- return XFS_ERROR(EINVAL);
- }
-
if (XFS_FORCED_SHUTDOWN(mp))
return XFS_ERROR(EIO);
- /*
- * Timestamps do not need to be logged and hence do not
- * need to be done within a transaction.
- */
- if (mask & XFS_AT_UPDTIMES) {
- ASSERT((mask & ~XFS_AT_UPDTIMES) == 0);
- timeflags = ((mask & XFS_AT_UPDATIME) ? XFS_ICHGTIME_ACC : 0) |
- ((mask & XFS_AT_UPDCTIME) ? XFS_ICHGTIME_CHG : 0) |
- ((mask & XFS_AT_UPDMTIME) ? XFS_ICHGTIME_MOD : 0);
- xfs_ichgtime(ip, timeflags);
- return 0;
- }
-
olddquot1 = olddquot2 = NULL;
udqp = gdqp = NULL;
* If the IDs do change before we take the ilock, we're covered
* because the i_*dquot fields will get updated anyway.
*/
- if (XFS_IS_QUOTA_ON(mp) &&
- (mask & (XFS_AT_UID|XFS_AT_GID|XFS_AT_PROJID))) {
+ if (XFS_IS_QUOTA_ON(mp) && (mask & (ATTR_UID|ATTR_GID))) {
uint qflags = 0;
- if ((mask & XFS_AT_UID) && XFS_IS_UQUOTA_ON(mp)) {
- uid = vap->va_uid;
+ if ((mask & ATTR_UID) && XFS_IS_UQUOTA_ON(mp)) {
+ uid = iattr->ia_uid;
qflags |= XFS_QMOPT_UQUOTA;
} else {
uid = ip->i_d.di_uid;
}
- if ((mask & XFS_AT_GID) && XFS_IS_GQUOTA_ON(mp)) {
- gid = vap->va_gid;
+ if ((mask & ATTR_GID) && XFS_IS_GQUOTA_ON(mp)) {
+ gid = iattr->ia_gid;
qflags |= XFS_QMOPT_GQUOTA;
} else {
gid = ip->i_d.di_gid;
}
- if ((mask & XFS_AT_PROJID) && XFS_IS_PQUOTA_ON(mp)) {
- projid = vap->va_projid;
- qflags |= XFS_QMOPT_PQUOTA;
- } else {
- projid = ip->i_d.di_projid;
- }
+
/*
* We take a reference when we initialize udqp and gdqp,
* so it is important that we never blindly double trip on
*/
ASSERT(udqp == NULL);
ASSERT(gdqp == NULL);
- code = XFS_QM_DQVOPALLOC(mp, ip, uid, gid, projid, qflags,
- &udqp, &gdqp);
+ code = XFS_QM_DQVOPALLOC(mp, ip, uid, gid, ip->i_d.di_projid,
+ qflags, &udqp, &gdqp);
if (code)
return code;
}
*/
tp = NULL;
lock_flags = XFS_ILOCK_EXCL;
- if (flags & ATTR_NOLOCK)
+ if (flags & XFS_ATTR_NOLOCK)
need_iolock = 0;
- if (!(mask & XFS_AT_SIZE)) {
- if ((mask != (XFS_AT_CTIME|XFS_AT_ATIME|XFS_AT_MTIME)) ||
+ if (!(mask & ATTR_SIZE)) {
+ if ((mask != (ATTR_CTIME|ATTR_ATIME|ATTR_MTIME)) ||
(mp->m_flags & XFS_MOUNT_WSYNC)) {
tp = xfs_trans_alloc(mp, XFS_TRANS_SETATTR_NOT_SIZE);
commit_flags = 0;
}
} else {
if (DM_EVENT_ENABLED(ip, DM_EVENT_TRUNCATE) &&
- !(flags & ATTR_DMI)) {
+ !(flags & XFS_ATTR_DMI)) {
int dmflags = AT_DELAY_FLAG(flags) | DM_SEM_FLAG_WR;
code = XFS_SEND_DATA(mp, DM_EVENT_TRUNCATE, ip,
- vap->va_size, 0, dmflags, NULL);
+ iattr->ia_size, 0, dmflags, NULL);
if (code) {
lock_flags = 0;
goto error_return;
* Only the owner or users with CAP_FOWNER
* capability may do these things.
*/
- if (mask &
- (XFS_AT_MODE|XFS_AT_XFLAGS|XFS_AT_EXTSIZE|XFS_AT_UID|
- XFS_AT_GID|XFS_AT_PROJID)) {
+ if (mask & (ATTR_MODE|ATTR_UID|ATTR_GID)) {
/*
* CAP_FOWNER overrides the following restrictions:
*
* IDs of the calling process shall match the group owner of
* the file when setting the set-group-ID bit on that file
*/
- if (mask & XFS_AT_MODE) {
+ if (mask & ATTR_MODE) {
mode_t m = 0;
- if ((vap->va_mode & S_ISUID) && !file_owner)
+ if ((iattr->ia_mode & S_ISUID) && !file_owner)
m |= S_ISUID;
- if ((vap->va_mode & S_ISGID) &&
+ if ((iattr->ia_mode & S_ISGID) &&
!in_group_p((gid_t)ip->i_d.di_gid))
m |= S_ISGID;
#if 0
/* Linux allows this, Irix doesn't. */
- if ((vap->va_mode & S_ISVTX) && !S_ISDIR(ip->i_d.di_mode))
+ if ((iattr->ia_mode & S_ISVTX) && !S_ISDIR(ip->i_d.di_mode))
m |= S_ISVTX;
#endif
if (m && !capable(CAP_FSETID))
- vap->va_mode &= ~m;
+ iattr->ia_mode &= ~m;
}
}
* and can change the group id only to a group of which he
* or she is a member.
*/
- if (mask & (XFS_AT_UID|XFS_AT_GID|XFS_AT_PROJID)) {
+ if (mask & (ATTR_UID|ATTR_GID)) {
/*
* These IDs could have changed since we last looked at them.
* But, we're assured that if the ownership did change
* would have changed also.
*/
iuid = ip->i_d.di_uid;
- iprojid = ip->i_d.di_projid;
igid = ip->i_d.di_gid;
- gid = (mask & XFS_AT_GID) ? vap->va_gid : igid;
- uid = (mask & XFS_AT_UID) ? vap->va_uid : iuid;
- projid = (mask & XFS_AT_PROJID) ? (xfs_prid_t)vap->va_projid :
- iprojid;
+ gid = (mask & ATTR_GID) ? iattr->ia_gid : igid;
+ uid = (mask & ATTR_UID) ? iattr->ia_uid : iuid;
/*
* CAP_CHOWN overrides the following restrictions:
goto error_return;
}
/*
- * Do a quota reservation only if uid/projid/gid is actually
+ * Do a quota reservation only if uid/gid is actually
* going to change.
*/
if ((XFS_IS_UQUOTA_ON(mp) && iuid != uid) ||
- (XFS_IS_PQUOTA_ON(mp) && iprojid != projid) ||
(XFS_IS_GQUOTA_ON(mp) && igid != gid)) {
ASSERT(tp);
code = XFS_QM_DQVOPCHOWNRESV(mp, tp, ip, udqp, gdqp,
/*
* Truncate file. Must have write permission and not be a directory.
*/
- if (mask & XFS_AT_SIZE) {
+ if (mask & ATTR_SIZE) {
/* Short circuit the truncate case for zero length files */
- if ((vap->va_size == 0) &&
- (ip->i_size == 0) && (ip->i_d.di_nextents == 0)) {
+ if (iattr->ia_size == 0 &&
+ ip->i_size == 0 && ip->i_d.di_nextents == 0) {
xfs_iunlock(ip, XFS_ILOCK_EXCL);
lock_flags &= ~XFS_ILOCK_EXCL;
- if (mask & XFS_AT_CTIME)
+ if (mask & ATTR_CTIME)
xfs_ichgtime(ip, XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG);
code = 0;
goto error_return;
/*
* Change file access or modified times.
*/
- if (mask & (XFS_AT_ATIME|XFS_AT_MTIME)) {
+ if (mask & (ATTR_ATIME|ATTR_MTIME)) {
if (!file_owner) {
- if ((flags & ATTR_UTIME) &&
+ if ((mask & (ATTR_MTIME_SET|ATTR_ATIME_SET)) &&
!capable(CAP_FOWNER)) {
code = XFS_ERROR(EPERM);
goto error_return;
}
}
- /*
- * Change extent size or realtime flag.
- */
- if (mask & (XFS_AT_EXTSIZE|XFS_AT_XFLAGS)) {
- /*
- * Can't change extent size if any extents are allocated.
- */
- if (ip->i_d.di_nextents && (mask & XFS_AT_EXTSIZE) &&
- ((ip->i_d.di_extsize << mp->m_sb.sb_blocklog) !=
- vap->va_extsize) ) {
- code = XFS_ERROR(EINVAL); /* EFBIG? */
- goto error_return;
- }
-
- /*
- * Can't change realtime flag if any extents are allocated.
- */
- if ((ip->i_d.di_nextents || ip->i_delayed_blks) &&
- (mask & XFS_AT_XFLAGS) &&
- (XFS_IS_REALTIME_INODE(ip)) !=
- (vap->va_xflags & XFS_XFLAG_REALTIME)) {
- code = XFS_ERROR(EINVAL); /* EFBIG? */
- goto error_return;
- }
- /*
- * Extent size must be a multiple of the appropriate block
- * size, if set at all.
- */
- if ((mask & XFS_AT_EXTSIZE) && vap->va_extsize != 0) {
- xfs_extlen_t size;
-
- if (XFS_IS_REALTIME_INODE(ip) ||
- ((mask & XFS_AT_XFLAGS) &&
- (vap->va_xflags & XFS_XFLAG_REALTIME))) {
- size = mp->m_sb.sb_rextsize <<
- mp->m_sb.sb_blocklog;
- } else {
- size = mp->m_sb.sb_blocksize;
- }
- if (vap->va_extsize % size) {
- code = XFS_ERROR(EINVAL);
- goto error_return;
- }
- }
- /*
- * If realtime flag is set then must have realtime data.
- */
- if ((mask & XFS_AT_XFLAGS) &&
- (vap->va_xflags & XFS_XFLAG_REALTIME)) {
- if ((mp->m_sb.sb_rblocks == 0) ||
- (mp->m_sb.sb_rextsize == 0) ||
- (ip->i_d.di_extsize % mp->m_sb.sb_rextsize)) {
- code = XFS_ERROR(EINVAL);
- goto error_return;
- }
- }
-
- /*
- * Can't modify an immutable/append-only file unless
- * we have appropriate permission.
- */
- if ((mask & XFS_AT_XFLAGS) &&
- (ip->i_d.di_flags &
- (XFS_DIFLAG_IMMUTABLE|XFS_DIFLAG_APPEND) ||
- (vap->va_xflags &
- (XFS_XFLAG_IMMUTABLE | XFS_XFLAG_APPEND))) &&
- !capable(CAP_LINUX_IMMUTABLE)) {
- code = XFS_ERROR(EPERM);
- goto error_return;
- }
- }
-
/*
* Now we can make the changes. Before we join the inode
- * to the transaction, if XFS_AT_SIZE is set then take care of
+ * to the transaction, if ATTR_SIZE is set then take care of
* the part of the truncation that must be done without the
* inode lock. This needs to be done before joining the inode
* to the transaction, because the inode cannot be unlocked
* once it is a part of the transaction.
*/
- if (mask & XFS_AT_SIZE) {
+ if (mask & ATTR_SIZE) {
code = 0;
- if ((vap->va_size > ip->i_size) &&
- (flags & ATTR_NOSIZETOK) == 0) {
- code = xfs_igrow_start(ip, vap->va_size, credp);
+ if (iattr->ia_size > ip->i_size) {
+ /*
+ * Do the first part of growing a file: zero any data
+ * in the last block that is beyond the old EOF. We
+ * need to do this before the inode is joined to the
+ * transaction to modify the i_size.
+ */
+ code = xfs_zero_eof(ip, iattr->ia_size, ip->i_size);
}
xfs_iunlock(ip, XFS_ILOCK_EXCL);
* not within the range we care about here.
*/
if (!code &&
- (ip->i_size != ip->i_d.di_size) &&
- (vap->va_size > ip->i_d.di_size)) {
+ ip->i_size != ip->i_d.di_size &&
+ iattr->ia_size > ip->i_d.di_size) {
code = xfs_flush_pages(ip,
- ip->i_d.di_size, vap->va_size,
+ ip->i_d.di_size, iattr->ia_size,
XFS_B_ASYNC, FI_NONE);
}
vn_iowait(ip);
if (!code)
- code = xfs_itruncate_data(ip, vap->va_size);
+ code = xfs_itruncate_data(ip, iattr->ia_size);
if (code) {
ASSERT(tp == NULL);
lock_flags &= ~XFS_ILOCK_EXCL;
/*
* Truncate file. Must have write permission and not be a directory.
*/
- if (mask & XFS_AT_SIZE) {
+ if (mask & ATTR_SIZE) {
/*
* Only change the c/mtime if we are changing the size
* or we are explicitly asked to change it. This handles
* the semantic difference between truncate() and ftruncate()
* as implemented in the VFS.
*/
- if (vap->va_size != ip->i_size || (mask & XFS_AT_CTIME))
+ if (iattr->ia_size != ip->i_size || (mask & ATTR_CTIME))
timeflags |= XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG;
- if (vap->va_size > ip->i_size) {
- xfs_igrow_finish(tp, ip, vap->va_size,
- !(flags & ATTR_DMI));
- } else if ((vap->va_size <= ip->i_size) ||
- ((vap->va_size == 0) && ip->i_d.di_nextents)) {
+ if (iattr->ia_size > ip->i_size) {
+ ip->i_d.di_size = iattr->ia_size;
+ ip->i_size = iattr->ia_size;
+ if (!(flags & XFS_ATTR_DMI))
+ xfs_ichgtime(ip, XFS_ICHGTIME_CHG);
+ xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
+ } else if (iattr->ia_size <= ip->i_size ||
+ (iattr->ia_size == 0 && ip->i_d.di_nextents)) {
/*
* signal a sync transaction unless
* we're truncating an already unlinked
* file on a wsync filesystem
*/
- code = xfs_itruncate_finish(&tp, ip,
- (xfs_fsize_t)vap->va_size,
+ code = xfs_itruncate_finish(&tp, ip, iattr->ia_size,
XFS_DATA_FORK,
((ip->i_d.di_nlink != 0 ||
!(mp->m_flags & XFS_MOUNT_WSYNC))
/*
* Change file access modes.
*/
- if (mask & XFS_AT_MODE) {
+ if (mask & ATTR_MODE) {
ip->i_d.di_mode &= S_IFMT;
- ip->i_d.di_mode |= vap->va_mode & ~S_IFMT;
+ ip->i_d.di_mode |= iattr->ia_mode & ~S_IFMT;
+
+ inode->i_mode &= S_IFMT;
+ inode->i_mode |= iattr->ia_mode & ~S_IFMT;
xfs_trans_log_inode (tp, ip, XFS_ILOG_CORE);
timeflags |= XFS_ICHGTIME_CHG;
* and can change the group id only to a group of which he
* or she is a member.
*/
- if (mask & (XFS_AT_UID|XFS_AT_GID|XFS_AT_PROJID)) {
+ if (mask & (ATTR_UID|ATTR_GID)) {
/*
* CAP_FSETID overrides the following restrictions:
*
*/
if (iuid != uid) {
if (XFS_IS_UQUOTA_ON(mp)) {
- ASSERT(mask & XFS_AT_UID);
+ ASSERT(mask & ATTR_UID);
ASSERT(udqp);
olddquot1 = XFS_QM_DQVOPCHOWN(mp, tp, ip,
&ip->i_udquot, udqp);
}
ip->i_d.di_uid = uid;
+ inode->i_uid = uid;
}
if (igid != gid) {
if (XFS_IS_GQUOTA_ON(mp)) {
ASSERT(!XFS_IS_PQUOTA_ON(mp));
- ASSERT(mask & XFS_AT_GID);
+ ASSERT(mask & ATTR_GID);
ASSERT(gdqp);
olddquot2 = XFS_QM_DQVOPCHOWN(mp, tp, ip,
&ip->i_gdquot, gdqp);
}
ip->i_d.di_gid = gid;
- }
- if (iprojid != projid) {
- if (XFS_IS_PQUOTA_ON(mp)) {
- ASSERT(!XFS_IS_GQUOTA_ON(mp));
- ASSERT(mask & XFS_AT_PROJID);
- ASSERT(gdqp);
- olddquot2 = XFS_QM_DQVOPCHOWN(mp, tp, ip,
- &ip->i_gdquot, gdqp);
- }
- ip->i_d.di_projid = projid;
- /*
- * We may have to rev the inode as well as
- * the superblock version number since projids didn't
- * exist before DINODE_VERSION_2 and SB_VERSION_NLINK.
- */
- if (ip->i_d.di_version == XFS_DINODE_VERSION_1)
- xfs_bump_ino_vers2(tp, ip);
+ inode->i_gid = gid;
}
xfs_trans_log_inode (tp, ip, XFS_ILOG_CORE);
/*
* Change file access or modified times.
*/
- if (mask & (XFS_AT_ATIME|XFS_AT_MTIME)) {
- if (mask & XFS_AT_ATIME) {
- ip->i_d.di_atime.t_sec = vap->va_atime.tv_sec;
- ip->i_d.di_atime.t_nsec = vap->va_atime.tv_nsec;
+ if (mask & (ATTR_ATIME|ATTR_MTIME)) {
+ if (mask & ATTR_ATIME) {
+ inode->i_atime = iattr->ia_atime;
+ ip->i_d.di_atime.t_sec = iattr->ia_atime.tv_sec;
+ ip->i_d.di_atime.t_nsec = iattr->ia_atime.tv_nsec;
ip->i_update_core = 1;
timeflags &= ~XFS_ICHGTIME_ACC;
}
- if (mask & XFS_AT_MTIME) {
- ip->i_d.di_mtime.t_sec = vap->va_mtime.tv_sec;
- ip->i_d.di_mtime.t_nsec = vap->va_mtime.tv_nsec;
+ if (mask & ATTR_MTIME) {
+ inode->i_mtime = iattr->ia_mtime;
+ ip->i_d.di_mtime.t_sec = iattr->ia_mtime.tv_sec;
+ ip->i_d.di_mtime.t_nsec = iattr->ia_mtime.tv_nsec;
timeflags &= ~XFS_ICHGTIME_MOD;
timeflags |= XFS_ICHGTIME_CHG;
}
- if (tp && (flags & ATTR_UTIME))
+ if (tp && (mask & (ATTR_MTIME_SET|ATTR_ATIME_SET)))
xfs_trans_log_inode (tp, ip, XFS_ILOG_CORE);
}
/*
- * Change XFS-added attributes.
- */
- if (mask & (XFS_AT_EXTSIZE|XFS_AT_XFLAGS)) {
- if (mask & XFS_AT_EXTSIZE) {
- /*
- * Converting bytes to fs blocks.
- */
- ip->i_d.di_extsize = vap->va_extsize >>
- mp->m_sb.sb_blocklog;
- }
- if (mask & XFS_AT_XFLAGS) {
- uint di_flags;
-
- /* can't set PREALLOC this way, just preserve it */
- di_flags = (ip->i_d.di_flags & XFS_DIFLAG_PREALLOC);
- if (vap->va_xflags & XFS_XFLAG_IMMUTABLE)
- di_flags |= XFS_DIFLAG_IMMUTABLE;
- if (vap->va_xflags & XFS_XFLAG_APPEND)
- di_flags |= XFS_DIFLAG_APPEND;
- if (vap->va_xflags & XFS_XFLAG_SYNC)
- di_flags |= XFS_DIFLAG_SYNC;
- if (vap->va_xflags & XFS_XFLAG_NOATIME)
- di_flags |= XFS_DIFLAG_NOATIME;
- if (vap->va_xflags & XFS_XFLAG_NODUMP)
- di_flags |= XFS_DIFLAG_NODUMP;
- if (vap->va_xflags & XFS_XFLAG_PROJINHERIT)
- di_flags |= XFS_DIFLAG_PROJINHERIT;
- if (vap->va_xflags & XFS_XFLAG_NODEFRAG)
- di_flags |= XFS_DIFLAG_NODEFRAG;
- if (vap->va_xflags & XFS_XFLAG_FILESTREAM)
- di_flags |= XFS_DIFLAG_FILESTREAM;
- if ((ip->i_d.di_mode & S_IFMT) == S_IFDIR) {
- if (vap->va_xflags & XFS_XFLAG_RTINHERIT)
- di_flags |= XFS_DIFLAG_RTINHERIT;
- if (vap->va_xflags & XFS_XFLAG_NOSYMLINKS)
- di_flags |= XFS_DIFLAG_NOSYMLINKS;
- if (vap->va_xflags & XFS_XFLAG_EXTSZINHERIT)
- di_flags |= XFS_DIFLAG_EXTSZINHERIT;
- } else if ((ip->i_d.di_mode & S_IFMT) == S_IFREG) {
- if (vap->va_xflags & XFS_XFLAG_REALTIME)
- di_flags |= XFS_DIFLAG_REALTIME;
- if (vap->va_xflags & XFS_XFLAG_EXTSIZE)
- di_flags |= XFS_DIFLAG_EXTSIZE;
- }
- ip->i_d.di_flags = di_flags;
- }
- xfs_trans_log_inode(tp, ip, XFS_ILOG_CORE);
- timeflags |= XFS_ICHGTIME_CHG;
- }
-
- /*
- * Change file inode change time only if XFS_AT_CTIME set
+ * Change file inode change time only if ATTR_CTIME set
* AND we have been called by a DMI function.
*/
- if ( (flags & ATTR_DMI) && (mask & XFS_AT_CTIME) ) {
- ip->i_d.di_ctime.t_sec = vap->va_ctime.tv_sec;
- ip->i_d.di_ctime.t_nsec = vap->va_ctime.tv_nsec;
+ if ((flags & XFS_ATTR_DMI) && (mask & ATTR_CTIME)) {
+ inode->i_ctime = iattr->ia_ctime;
+ ip->i_d.di_ctime.t_sec = iattr->ia_ctime.tv_sec;
+ ip->i_d.di_ctime.t_nsec = iattr->ia_ctime.tv_nsec;
ip->i_update_core = 1;
timeflags &= ~XFS_ICHGTIME_CHG;
}
* Send out timestamp changes that need to be set to the
* current time. Not done when called by a DMI function.
*/
- if (timeflags && !(flags & ATTR_DMI))
+ if (timeflags && !(flags & XFS_ATTR_DMI))
xfs_ichgtime(ip, timeflags);
XFS_STATS_INC(xs_ig_attrchg);
}
if (DM_EVENT_ENABLED(ip, DM_EVENT_ATTRIBUTE) &&
- !(flags & ATTR_DMI)) {
+ !(flags & XFS_ATTR_DMI)) {
(void) XFS_SEND_NAMESP(mp, DM_EVENT_ATTRIBUTE, ip, DM_RIGHT_NULL,
NULL, DM_RIGHT_NULL, NULL, NULL,
0, 0, AT_DELAY_FLAG(flags));
return VN_INACTIVE_CACHE;
}
-
+/*
+ * Lookups up an inode from "name". If ci_name is not NULL, then a CI match
+ * is allowed, otherwise it has to be an exact match. If a CI match is found,
+ * ci_name->name will point to a the actual name (caller must free) or
+ * will be set to NULL if an exact match is found.
+ */
int
xfs_lookup(
xfs_inode_t *dp,
struct xfs_name *name,
- xfs_inode_t **ipp)
+ xfs_inode_t **ipp,
+ struct xfs_name *ci_name)
{
xfs_ino_t inum;
int error;
return XFS_ERROR(EIO);
lock_mode = xfs_ilock_map_shared(dp);
- error = xfs_dir_lookup(NULL, dp, name, &inum);
+ error = xfs_dir_lookup(NULL, dp, name, &inum, ci_name);
xfs_iunlock_map_shared(dp, lock_mode);
if (error)
error = xfs_iget(dp->i_mount, NULL, inum, 0, 0, ipp, 0);
if (error)
- goto out;
+ goto out_free_name;
xfs_itrace_ref(*ipp);
return 0;
- out:
+out_free_name:
+ if (ci_name)
+ kmem_free(ci_name->name);
+out:
*ipp = NULL;
return error;
}
#endif
}
-#ifdef DEBUG
-#define REMOVE_DEBUG_TRACE(x) {remove_which_error_return = (x);}
-int remove_which_error_return = 0;
-#else /* ! DEBUG */
-#define REMOVE_DEBUG_TRACE(x)
-#endif /* ! DEBUG */
-
int
xfs_remove(
xfs_inode_t *dp,
{
xfs_mount_t *mp = dp->i_mount;
xfs_trans_t *tp = NULL;
+ int is_dir = S_ISDIR(ip->i_d.di_mode);
int error = 0;
xfs_bmap_free_t free_list;
xfs_fsblock_t first_block;
int committed;
int link_zero;
uint resblks;
+ uint log_count;
xfs_itrace_entry(dp);
+ xfs_itrace_entry(ip);
if (XFS_FORCED_SHUTDOWN(mp))
return XFS_ERROR(EIO);
return error;
}
- xfs_itrace_entry(ip);
- xfs_itrace_ref(ip);
-
error = XFS_QM_DQATTACH(mp, dp, 0);
- if (!error)
- error = XFS_QM_DQATTACH(mp, ip, 0);
- if (error) {
- REMOVE_DEBUG_TRACE(__LINE__);
+ if (error)
+ goto std_return;
+
+ error = XFS_QM_DQATTACH(mp, ip, 0);
+ if (error)
goto std_return;
- }
- tp = xfs_trans_alloc(mp, XFS_TRANS_REMOVE);
+ if (is_dir) {
+ tp = xfs_trans_alloc(mp, XFS_TRANS_RMDIR);
+ log_count = XFS_DEFAULT_LOG_COUNT;
+ } else {
+ tp = xfs_trans_alloc(mp, XFS_TRANS_REMOVE);
+ log_count = XFS_REMOVE_LOG_COUNT;
+ }
cancel_flags = XFS_TRANS_RELEASE_LOG_RES;
+
/*
* We try to get the real space reservation first,
* allowing for directory btree deletion(s) implying
*/
resblks = XFS_REMOVE_SPACE_RES(mp);
error = xfs_trans_reserve(tp, resblks, XFS_REMOVE_LOG_RES(mp), 0,
- XFS_TRANS_PERM_LOG_RES, XFS_REMOVE_LOG_COUNT);
+ XFS_TRANS_PERM_LOG_RES, log_count);
if (error == ENOSPC) {
resblks = 0;
error = xfs_trans_reserve(tp, 0, XFS_REMOVE_LOG_RES(mp), 0,
- XFS_TRANS_PERM_LOG_RES, XFS_REMOVE_LOG_COUNT);
+ XFS_TRANS_PERM_LOG_RES, log_count);
}
if (error) {
ASSERT(error != ENOSPC);
- REMOVE_DEBUG_TRACE(__LINE__);
- xfs_trans_cancel(tp, 0);
- return error;
+ cancel_flags = 0;
+ goto out_trans_cancel;
}
error = xfs_lock_dir_and_entry(dp, ip);
- if (error) {
- REMOVE_DEBUG_TRACE(__LINE__);
- xfs_trans_cancel(tp, cancel_flags);
- goto std_return;
- }
+ if (error)
+ goto out_trans_cancel;
/*
* At this point, we've gotten both the directory and the entry
IHOLD(dp);
xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL);
+ /*
+ * If we're removing a directory perform some additional validation.
+ */
+ if (is_dir) {
+ ASSERT(ip->i_d.di_nlink >= 2);
+ if (ip->i_d.di_nlink != 2) {
+ error = XFS_ERROR(ENOTEMPTY);
+ goto out_trans_cancel;
+ }
+ if (!xfs_dir_isempty(ip)) {
+ error = XFS_ERROR(ENOTEMPTY);
+ goto out_trans_cancel;
+ }
+ }
+
/*
* Entry must exist since we did a lookup in xfs_lock_dir_and_entry.
*/
&first_block, &free_list, resblks);
if (error) {
ASSERT(error != ENOENT);
- REMOVE_DEBUG_TRACE(__LINE__);
- goto error1;
+ goto out_bmap_cancel;
}
xfs_ichgtime(dp, XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG);
+ /*
+ * Bump the in memory generation count on the parent
+ * directory so that other can know that it has changed.
+ */
dp->i_gen++;
xfs_trans_log_inode(tp, dp, XFS_ILOG_CORE);
- error = xfs_droplink(tp, ip);
- if (error) {
- REMOVE_DEBUG_TRACE(__LINE__);
- goto error1;
+ if (is_dir) {
+ /*
+ * Drop the link from ip's "..".
+ */
+ error = xfs_droplink(tp, dp);
+ if (error)
+ goto out_bmap_cancel;
+
+ /*
+ * Drop the link from dp to ip.
+ */
+ error = xfs_droplink(tp, ip);
+ if (error)
+ goto out_bmap_cancel;
+ } else {
+ /*
+ * When removing a non-directory we need to log the parent
+ * inode here for the i_gen update. For a directory this is
+ * done implicitly by the xfs_droplink call for the ".." entry.
+ */
+ xfs_trans_log_inode(tp, dp, XFS_ILOG_CORE);
}
- /* Determine if this is the last link while
+ /*
+ * Drop the "." link from ip to self.
+ */
+ error = xfs_droplink(tp, ip);
+ if (error)
+ goto out_bmap_cancel;
+
+ /*
+ * Determine if this is the last link while
* we are in the transaction.
*/
- link_zero = (ip)->i_d.di_nlink==0;
+ link_zero = (ip->i_d.di_nlink == 0);
/*
* If this is a synchronous mount, make sure that the
* remove transaction goes to disk before returning to
* the user.
*/
- if (mp->m_flags & (XFS_MOUNT_WSYNC|XFS_MOUNT_DIRSYNC)) {
+ if (mp->m_flags & (XFS_MOUNT_WSYNC|XFS_MOUNT_DIRSYNC))
xfs_trans_set_sync(tp);
- }
error = xfs_bmap_finish(&tp, &free_list, &committed);
- if (error) {
- REMOVE_DEBUG_TRACE(__LINE__);
- goto error_rele;
- }
+ if (error)
+ goto out_bmap_cancel;
error = xfs_trans_commit(tp, XFS_TRANS_RELEASE_LOG_RES);
if (error)
* will get killed on last close in xfs_close() so we don't
* have to worry about that.
*/
- if (link_zero && xfs_inode_is_filestream(ip))
+ if (!is_dir && link_zero && xfs_inode_is_filestream(ip))
xfs_filestream_deassociate(ip);
xfs_itrace_exit(ip);
+ xfs_itrace_exit(dp);
-/* Fall through to std_return with error = 0 */
std_return:
if (DM_EVENT_ENABLED(dp, DM_EVENT_POSTREMOVE)) {
- (void) XFS_SEND_NAMESP(mp, DM_EVENT_POSTREMOVE,
- dp, DM_RIGHT_NULL,
- NULL, DM_RIGHT_NULL,
- name->name, NULL, ip->i_d.di_mode, error, 0);
+ XFS_SEND_NAMESP(mp, DM_EVENT_POSTREMOVE, dp, DM_RIGHT_NULL,
+ NULL, DM_RIGHT_NULL, name->name, NULL,
+ ip->i_d.di_mode, error, 0);
}
- return error;
- error1:
- xfs_bmap_cancel(&free_list);
- cancel_flags |= XFS_TRANS_ABORT;
- xfs_trans_cancel(tp, cancel_flags);
- goto std_return;
+ return error;
- error_rele:
- /*
- * In this case make sure to not release the inode until after
- * the current transaction is aborted. Releasing it beforehand
- * can cause us to go to xfs_inactive and start a recursive
- * transaction which can easily deadlock with the current one.
- */
+ out_bmap_cancel:
xfs_bmap_cancel(&free_list);
cancel_flags |= XFS_TRANS_ABORT;
+ out_trans_cancel:
xfs_trans_cancel(tp, cancel_flags);
-
goto std_return;
}
goto std_return;
}
-int
-xfs_rmdir(
- xfs_inode_t *dp,
- struct xfs_name *name,
- xfs_inode_t *cdp)
-{
- xfs_mount_t *mp = dp->i_mount;
- xfs_trans_t *tp;
- int error;
- xfs_bmap_free_t free_list;
- xfs_fsblock_t first_block;
- int cancel_flags;
- int committed;
- int last_cdp_link;
- uint resblks;
-
- xfs_itrace_entry(dp);
-
- if (XFS_FORCED_SHUTDOWN(mp))
- return XFS_ERROR(EIO);
-
- if (DM_EVENT_ENABLED(dp, DM_EVENT_REMOVE)) {
- error = XFS_SEND_NAMESP(mp, DM_EVENT_REMOVE,
- dp, DM_RIGHT_NULL,
- NULL, DM_RIGHT_NULL, name->name,
- NULL, cdp->i_d.di_mode, 0, 0);
- if (error)
- return XFS_ERROR(error);
- }
-
- /*
- * Get the dquots for the inodes.
- */
- error = XFS_QM_DQATTACH(mp, dp, 0);
- if (!error)
- error = XFS_QM_DQATTACH(mp, cdp, 0);
- if (error) {
- REMOVE_DEBUG_TRACE(__LINE__);
- goto std_return;
- }
-
- tp = xfs_trans_alloc(mp, XFS_TRANS_RMDIR);
- cancel_flags = XFS_TRANS_RELEASE_LOG_RES;
- /*
- * We try to get the real space reservation first,
- * allowing for directory btree deletion(s) implying
- * possible bmap insert(s). If we can't get the space
- * reservation then we use 0 instead, and avoid the bmap
- * btree insert(s) in the directory code by, if the bmap
- * insert tries to happen, instead trimming the LAST
- * block from the directory.
- */
- resblks = XFS_REMOVE_SPACE_RES(mp);
- error = xfs_trans_reserve(tp, resblks, XFS_REMOVE_LOG_RES(mp), 0,
- XFS_TRANS_PERM_LOG_RES, XFS_DEFAULT_LOG_COUNT);
- if (error == ENOSPC) {
- resblks = 0;
- error = xfs_trans_reserve(tp, 0, XFS_REMOVE_LOG_RES(mp), 0,
- XFS_TRANS_PERM_LOG_RES, XFS_DEFAULT_LOG_COUNT);
- }
- if (error) {
- ASSERT(error != ENOSPC);
- cancel_flags = 0;
- goto error_return;
- }
- XFS_BMAP_INIT(&free_list, &first_block);
-
- /*
- * Now lock the child directory inode and the parent directory
- * inode in the proper order. This will take care of validating
- * that the directory entry for the child directory inode has
- * not changed while we were obtaining a log reservation.
- */
- error = xfs_lock_dir_and_entry(dp, cdp);
- if (error) {
- xfs_trans_cancel(tp, cancel_flags);
- goto std_return;
- }
-
- IHOLD(dp);
- xfs_trans_ijoin(tp, dp, XFS_ILOCK_EXCL);
-
- IHOLD(cdp);
- xfs_trans_ijoin(tp, cdp, XFS_ILOCK_EXCL);
-
- ASSERT(cdp->i_d.di_nlink >= 2);
- if (cdp->i_d.di_nlink != 2) {
- error = XFS_ERROR(ENOTEMPTY);
- goto error_return;
- }
- if (!xfs_dir_isempty(cdp)) {
- error = XFS_ERROR(ENOTEMPTY);
- goto error_return;
- }
-
- error = xfs_dir_removename(tp, dp, name, cdp->i_ino,
- &first_block, &free_list, resblks);
- if (error)
- goto error1;
-
- xfs_ichgtime(dp, XFS_ICHGTIME_MOD | XFS_ICHGTIME_CHG);
-
- /*
- * Bump the in memory generation count on the parent
- * directory so that other can know that it has changed.
- */
- dp->i_gen++;
-
- /*
- * Drop the link from cdp's "..".
- */
- error = xfs_droplink(tp, dp);
- if (error) {
- goto error1;
- }
-
- /*
- * Drop the link from dp to cdp.
- */
- error = xfs_droplink(tp, cdp);
- if (error) {
- goto error1;
- }
-
- /*
- * Drop the "." link from cdp to self.
- */
- error = xfs_droplink(tp, cdp);
- if (error) {
- goto error1;
- }
-
- /* Determine these before committing transaction */
- last_cdp_link = (cdp)->i_d.di_nlink==0;
-
- /*
- * If this is a synchronous mount, make sure that the
- * rmdir transaction goes to disk before returning to
- * the user.
- */
- if (mp->m_flags & (XFS_MOUNT_WSYNC|XFS_MOUNT_DIRSYNC)) {
- xfs_trans_set_sync(tp);
- }
-
- error = xfs_bmap_finish (&tp, &free_list, &committed);
- if (error) {
- xfs_bmap_cancel(&free_list);
- xfs_trans_cancel(tp, (XFS_TRANS_RELEASE_LOG_RES |
- XFS_TRANS_ABORT));
- goto std_return;
- }
-
- error = xfs_trans_commit(tp, XFS_TRANS_RELEASE_LOG_RES);
- if (error) {
- goto std_return;
- }
-
-
- /* Fall through to std_return with error = 0 or the errno
- * from xfs_trans_commit. */
- std_return:
- if (DM_EVENT_ENABLED(dp, DM_EVENT_POSTREMOVE)) {
- (void) XFS_SEND_NAMESP(mp, DM_EVENT_POSTREMOVE,
- dp, DM_RIGHT_NULL,
- NULL, DM_RIGHT_NULL,
- name->name, NULL, cdp->i_d.di_mode,
- error, 0);
- }
- return error;
-
- error1:
- xfs_bmap_cancel(&free_list);
- cancel_flags |= XFS_TRANS_ABORT;
- /* FALLTHROUGH */
-
- error_return:
- xfs_trans_cancel(tp, cancel_flags);
- goto std_return;
-}
-
int
xfs_symlink(
xfs_inode_t *dp,
{
xfs_perag_t *pag = xfs_get_perag(ip->i_mount, ip->i_ino);
bhv_vnode_t *vp = XFS_ITOV_NULL(ip);
- int error;
if (vp && VN_BAD(vp))
goto reclaim;
xfs_iflock(ip);
}
- if (!XFS_FORCED_SHUTDOWN(ip->i_mount)) {
- if (ip->i_update_core ||
- ((ip->i_itemp != NULL) &&
- (ip->i_itemp->ili_format.ilf_fields != 0))) {
- error = xfs_iflush(ip, sync_mode);
- /*
- * If we hit an error, typically because of filesystem
- * shutdown, we don't need to let vn_reclaim to know
- * because we're gonna reclaim the inode anyway.
- */
- if (error) {
- xfs_iunlock(ip, XFS_ILOCK_EXCL);
- goto reclaim;
- }
- xfs_iflock(ip); /* synchronize with xfs_iflush_done */
- }
-
- ASSERT(ip->i_update_core == 0);
- ASSERT(ip->i_itemp == NULL ||
- ip->i_itemp->ili_format.ilf_fields == 0);
+ /*
+ * In the case of a forced shutdown we rely on xfs_iflush() to
+ * wait for the inode to be unpinned before returning an error.
+ */
+ if (xfs_iflush(ip, sync_mode) == 0) {
+ /* synchronize with xfs_iflush_done */
+ xfs_iflock(ip);
+ xfs_ifunlock(ip);
}
- xfs_ifunlock(ip);
xfs_iunlock(ip, XFS_ILOCK_EXCL);
reclaim:
/* Generate a DMAPI event if needed. */
if (alloc_type != 0 && offset < ip->i_size &&
- (attr_flags&ATTR_DMI) == 0 &&
+ (attr_flags & XFS_ATTR_DMI) == 0 &&
DM_EVENT_ENABLED(ip, DM_EVENT_WRITE)) {
xfs_off_t end_dmi_offset;
allocatesize_fsb -= allocated_fsb;
}
dmapi_enospc_check:
- if (error == ENOSPC && (attr_flags & ATTR_DMI) == 0 &&
+ if (error == ENOSPC && (attr_flags & XFS_ATTR_DMI) == 0 &&
DM_EVENT_ENABLED(ip, DM_EVENT_NOSPACE)) {
error = XFS_SEND_NAMESP(mp, DM_EVENT_NOSPACE,
ip, DM_RIGHT_NULL,
end_dmi_offset = offset + len;
endoffset_fsb = XFS_B_TO_FSBT(mp, end_dmi_offset);
- if (offset < ip->i_size && (attr_flags & ATTR_DMI) == 0 &&
+ if (offset < ip->i_size && (attr_flags & XFS_ATTR_DMI) == 0 &&
DM_EVENT_ENABLED(ip, DM_EVENT_WRITE)) {
if (end_dmi_offset > ip->i_size)
end_dmi_offset = ip->i_size;
return error;
}
- if (attr_flags & ATTR_NOLOCK)
+ if (attr_flags & XFS_ATTR_NOLOCK)
need_iolock = 0;
if (need_iolock) {
xfs_ilock(ip, XFS_IOLOCK_EXCL);
xfs_off_t startoffset;
xfs_off_t llen;
xfs_trans_t *tp;
- bhv_vattr_t va;
+ struct iattr iattr;
xfs_itrace_entry(ip);
break;
}
- va.va_mask = XFS_AT_SIZE;
- va.va_size = startoffset;
+ iattr.ia_valid = ATTR_SIZE;
+ iattr.ia_size = startoffset;
- error = xfs_setattr(ip, &va, attr_flags, credp);
+ error = xfs_setattr(ip, &iattr, attr_flags, credp);
if (error)
return error;
xfs_trans_ijoin(tp, ip, XFS_ILOCK_EXCL);
xfs_trans_ihold(tp, ip);
- if ((attr_flags & ATTR_DMI) == 0) {
+ if ((attr_flags & XFS_ATTR_DMI) == 0) {
ip->i_d.di_mode &= ~S_ISUID;
/*
#define _XFS_VNODEOPS_H 1
struct attrlist_cursor_kern;
-struct bhv_vattr;
struct cred;
struct file;
+struct iattr;
struct inode;
struct iovec;
struct kiocb;
int xfs_open(struct xfs_inode *ip);
-int xfs_setattr(struct xfs_inode *ip, struct bhv_vattr *vap, int flags,
+int xfs_setattr(struct xfs_inode *ip, struct iattr *vap, int flags,
struct cred *credp);
+#define XFS_ATTR_DMI 0x01 /* invocation from a DMI function */
+#define XFS_ATTR_NONBLOCK 0x02 /* return EAGAIN if operation would block */
+#define XFS_ATTR_NOLOCK 0x04 /* Don't grab any conflicting locks */
+
int xfs_readlink(struct xfs_inode *ip, char *link);
int xfs_fsync(struct xfs_inode *ip);
int xfs_release(struct xfs_inode *ip);
int xfs_inactive(struct xfs_inode *ip);
int xfs_lookup(struct xfs_inode *dp, struct xfs_name *name,
- struct xfs_inode **ipp);
+ struct xfs_inode **ipp, struct xfs_name *ci_name);
int xfs_create(struct xfs_inode *dp, struct xfs_name *name, mode_t mode,
xfs_dev_t rdev, struct xfs_inode **ipp, struct cred *credp);
int xfs_remove(struct xfs_inode *dp, struct xfs_name *name,
struct xfs_name *target_name);
int xfs_mkdir(struct xfs_inode *dp, struct xfs_name *dir_name,
mode_t mode, struct xfs_inode **ipp, struct cred *credp);
-int xfs_rmdir(struct xfs_inode *dp, struct xfs_name *name,
- struct xfs_inode *cdp);
int xfs_readdir(struct xfs_inode *dp, void *dirent, size_t bufsize,
xfs_off_t *offset, filldir_t filldir);
int xfs_symlink(struct xfs_inode *dp, struct xfs_name *link_name,
+++ /dev/null
-/*
- * linux/include/asm-arm/arch-ep93xx/dma.h
- */
+++ /dev/null
-/*
- * linux/include/asm-arm/arch-ep93xx/gesbc9312.h
- */
+++ /dev/null
-/*
- * linux/include/asm-arm/arch-ep93xx/timex.h
- */
-
-#define CLOCK_TICK_RATE 983040
+++ /dev/null
-/*
- * linux/include/asm-arm/arch-ep93xx/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe800000
+++ /dev/null
-/*
- * include/asm-arm/arch-iop32x/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe000000
+++ /dev/null
-/*
- * include/asm-arm/arch-iop33x/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe000000
+++ /dev/null
-/*
- * include/asm-arm/arch-ixp23xx/dma.h
- */
+++ /dev/null
-/*
- * include/asm-arm/arch-ixp23xx/time.h
- */
+++ /dev/null
-/*
- * include/asm-arm/arch-kirkwood/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe800000
+++ /dev/null
-/*
- * include/asm-arm/arch-loki/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe800000
+++ /dev/null
-/*
- * include/asm-arm/arch-mv78xx0/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe000000
+++ /dev/null
-/*
- * include/asm-arm/arch-orion5x/vmalloc.h
- */
-
-#define VMALLOC_END 0xfd800000
+++ /dev/null
-/*
- * linux/include/asm-arm/arch-sa1100/vmalloc.h
- */
-#define VMALLOC_END (0xe8000000)
+++ /dev/null
-/*
- * linux/include/asm-arm/hardware.h
- *
- * Copyright (C) 1996 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Common hardware definitions
- */
-
-#ifndef __ASM_HARDWARE_H
-#define __ASM_HARDWARE_H
-
-#include <asm/arch/hardware.h>
-
-#endif
+++ /dev/null
-/*
- * Nothing to see here yet
- */
-#ifndef _ARCH_ARM_HW_IRQ_H
-#define _ARCH_ARM_HW_IRQ_H
-
-#include <asm/mach/irq.h>
-
-#endif
-/* linux/include/asm-arm/arch-s3c2410/iic.h
+/* arch/arm/mach-s3c2410/include/mach/iic.h
*
* Copyright (c) 2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/nand.h
+/* arch/arm/mach-s3c2410/include/mach/nand.h
*
* Copyright (c) 2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
-/* linux/include/asm-arm/arch-s3c2410/regs-ac97.h
+/* arch/arm/mach-s3c2410/include/mach/regs-ac97.h
*
* Copyright (c) 2006 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-adc.h
+/* arch/arm/mach-s3c2410/include/mach/regs-adc.h
*
* Copyright (c) 2004 Shannon Holland <holland@loser.net>
*
-/* linux/include/asm-arm/arch-s3c2410/regs-iic.h
+/* arch/arm/mach-s3c2410/include/mach/regs-iic.h
*
* Copyright (c) 2004 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-nand.h
+/* arch/arm/mach-s3c2410/include/mach/regs-nand.h
*
* Copyright (c) 2004,2005 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-rtc.h
+/* arch/arm/mach-s3c2410/include/mach/regs-rtc.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-serial.h
+/* arch/arm/mach-s3c2410/include/mach/regs-serial.h
*
* From linux/include/asm-arm/hardware/serial_s3c2410.h
*
-/* linux/include/asm-arm/arch-s3c2410/regs-timer.h
+/* arch/arm/mach-s3c2410/include/mach/regs-timer.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-watchdog.h
+/* arch/arm/mach-s3c2410/include/mach/regs-watchdog.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-iis.h
+/* arch/arm/mach-s3c2410/include/mach/regs-iis.h
*
* Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
* http://www.simtec.co.uk/products/SWLINUX/
-/* linux/include/asm-arm/arch-s3c2410/regs-spi.h
+/* arch/arm/mach-s3c2410/include/mach/regs-spi.h
*
* Copyright (c) 2004 Fetron GmbH
*
-/* linux/include/asm-arm/arch-s3c2410/regs-udc.h
+/* arch/arm/mach-s3c2410/include/mach/regs-udc.h
*
* Copyright (C) 2004 Herbert Poetzl <herbert@13thfloor.at>
*
-/* linux/include/asm-arm/arch-s3c2410/udc.h
+/* arch/arm/mach-s3c2410/include/mach/udc.h
*
* Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org>
*
#define __NR_fallocate 324
#define __NR_timerfd_settime 325
#define __NR_timerfd_gettime 326
+#define __NR_signalfd4 327
+#define __NR_eventfd2 328
+#define __NR_epoll_create1 329
+#define __NR_dup3 330
+#define __NR_pipe2 331
+#define __NR_inotify_init1 332
#ifdef __KERNEL__
-#define NR_syscalls 325
+#define NR_syscalls 333
#define __ARCH_WANT_IPC_PARSE_VERSION
/* #define __ARCH_WANT_OLD_READDIR */
#define BUG_TABLE \
. = ALIGN(8); \
__bug_table : AT(ADDR(__bug_table) - LOAD_OFFSET) { \
- __start___bug_table = .; \
+ VMLINUX_SYMBOL(__start___bug_table) = .; \
*(__bug_table) \
- __stop___bug_table = .; \
+ VMLINUX_SYMBOL(__stop___bug_table) = .; \
}
#else
#define BUG_TABLE
#define TRACEDATA \
. = ALIGN(4); \
.tracedata : AT(ADDR(.tracedata) - LOAD_OFFSET) { \
- __tracedata_start = .; \
+ VMLINUX_SYMBOL(__tracedata_start) = .; \
*(.tracedata) \
- __tracedata_end = .; \
+ VMLINUX_SYMBOL(__tracedata_end) = .; \
}
#else
#define TRACEDATA
#define INITCALLS \
*(.initcallearly.init) \
- __early_initcall_end = .; \
+ VMLINUX_SYMBOL(__early_initcall_end) = .; \
*(.initcall0.init) \
*(.initcall0s.init) \
*(.initcall1.init) \
#define PERCPU(align) \
. = ALIGN(align); \
- __per_cpu_start = .; \
+ VMLINUX_SYMBOL(__per_cpu_start) = .; \
.data.percpu : AT(ADDR(.data.percpu) - LOAD_OFFSET) { \
*(.data.percpu) \
*(.data.percpu.shared_aligned) \
} \
- __per_cpu_end = .;
+ VMLINUX_SYMBOL(__per_cpu_end) = .;
#ifndef _M68K_CONTREGS_H
#define _M68K_CONTREGS_H
-#include <asm-sparc/contregs.h>
+
+/* contregs.h: Addresses of registers in the ASI_CONTROL alternate address
+ * space. These are for the mmu's context register, etc.
+ *
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+
+/* 3=sun3
+ 4=sun4 (as in sun4 sysmaint student book)
+ c=sun4c (according to davem) */
+
+#define AC_IDPROM 0x00000000 /* 34 ID PROM, R/O, byte, 32 bytes */
+#define AC_PAGEMAP 0x10000000 /* 3 Pagemap R/W, long */
+#define AC_SEGMAP 0x20000000 /* 3 Segment map, byte */
+#define AC_CONTEXT 0x30000000 /* 34c current mmu-context */
+#define AC_SENABLE 0x40000000 /* 34c system dvma/cache/reset enable reg*/
+#define AC_UDVMA_ENB 0x50000000 /* 34 Not used on Sun boards, byte */
+#define AC_BUS_ERROR 0x60000000 /* 34 Not cleared on read, byte. */
+#define AC_SYNC_ERR 0x60000000 /* c fault type */
+#define AC_SYNC_VA 0x60000004 /* c fault virtual address */
+#define AC_ASYNC_ERR 0x60000008 /* c asynchronous fault type */
+#define AC_ASYNC_VA 0x6000000c /* c async fault virtual address */
+#define AC_LEDS 0x70000000 /* 34 Zero turns on LEDs, byte */
+#define AC_CACHETAGS 0x80000000 /* 34c direct access to the VAC tags */
+#define AC_CACHEDDATA 0x90000000 /* 3 c direct access to the VAC data */
+#define AC_UDVMA_MAP 0xD0000000 /* 4 Not used on Sun boards, byte */
+#define AC_VME_VECTOR 0xE0000000 /* 4 For non-Autovector VME, byte */
+#define AC_BOOT_SCC 0xF0000000 /* 34 bypass to access Zilog 8530. byte.*/
+
+/* s=Swift, h=Ross_HyperSPARC, v=TI_Viking, t=Tsunami, r=Ross_Cypress */
+#define AC_M_PCR 0x0000 /* shv Processor Control Reg */
+#define AC_M_CTPR 0x0100 /* shv Context Table Pointer Reg */
+#define AC_M_CXR 0x0200 /* shv Context Register */
+#define AC_M_SFSR 0x0300 /* shv Synchronous Fault Status Reg */
+#define AC_M_SFAR 0x0400 /* shv Synchronous Fault Address Reg */
+#define AC_M_AFSR 0x0500 /* hv Asynchronous Fault Status Reg */
+#define AC_M_AFAR 0x0600 /* hv Asynchronous Fault Address Reg */
+#define AC_M_RESET 0x0700 /* hv Reset Reg */
+#define AC_M_RPR 0x1000 /* hv Root Pointer Reg */
+#define AC_M_TSUTRCR 0x1000 /* s TLB Replacement Ctrl Reg */
+#define AC_M_IAPTP 0x1100 /* hv Instruction Access PTP */
+#define AC_M_DAPTP 0x1200 /* hv Data Access PTP */
+#define AC_M_ITR 0x1300 /* hv Index Tag Register */
+#define AC_M_TRCR 0x1400 /* hv TLB Replacement Control Reg */
+#define AC_M_SFSRX 0x1300 /* s Synch Fault Status Reg prim */
+#define AC_M_SFARX 0x1400 /* s Synch Fault Address Reg prim */
+#define AC_M_RPR1 0x1500 /* h Root Pointer Reg (entry 2) */
+#define AC_M_IAPTP1 0x1600 /* h Instruction Access PTP (entry 2) */
+#define AC_M_DAPTP1 0x1700 /* h Data Access PTP (entry 2) */
+
#endif /* _M68K_CONTREGS_H */
-#include <asm-sparc/fbio.h>
+#ifndef __LINUX_FBIO_H
+#define __LINUX_FBIO_H
+
+#include <linux/compiler.h>
+#include <linux/types.h>
+
+/* Constants used for fbio SunOS compatibility */
+/* (C) 1996 Miguel de Icaza */
+
+/* Frame buffer types */
+#define FBTYPE_NOTYPE -1
+#define FBTYPE_SUN1BW 0 /* mono */
+#define FBTYPE_SUN1COLOR 1
+#define FBTYPE_SUN2BW 2
+#define FBTYPE_SUN2COLOR 3
+#define FBTYPE_SUN2GP 4
+#define FBTYPE_SUN5COLOR 5
+#define FBTYPE_SUN3COLOR 6
+#define FBTYPE_MEMCOLOR 7
+#define FBTYPE_SUN4COLOR 8
+
+#define FBTYPE_NOTSUN1 9
+#define FBTYPE_NOTSUN2 10
+#define FBTYPE_NOTSUN3 11
+
+#define FBTYPE_SUNFAST_COLOR 12 /* cg6 */
+#define FBTYPE_SUNROP_COLOR 13
+#define FBTYPE_SUNFB_VIDEO 14
+#define FBTYPE_SUNGIFB 15
+#define FBTYPE_SUNGPLAS 16
+#define FBTYPE_SUNGP3 17
+#define FBTYPE_SUNGT 18
+#define FBTYPE_SUNLEO 19 /* zx Leo card */
+#define FBTYPE_MDICOLOR 20 /* cg14 */
+#define FBTYPE_TCXCOLOR 21 /* SUNW,tcx card */
+
+#define FBTYPE_LASTPLUSONE 21 /* This is not last + 1 in fact... */
+
+/* Does not seem to be listed in the Sun file either */
+#define FBTYPE_CREATOR 22
+#define FBTYPE_PCI_IGA1682 23
+#define FBTYPE_P9100COLOR 24
+
+#define FBTYPE_PCI_GENERIC 1000
+#define FBTYPE_PCI_MACH64 1001
+
+/* fbio ioctls */
+/* Returned by FBIOGTYPE */
+struct fbtype {
+ int fb_type; /* fb type, see above */
+ int fb_height; /* pixels */
+ int fb_width; /* pixels */
+ int fb_depth;
+ int fb_cmsize; /* color map entries */
+ int fb_size; /* fb size in bytes */
+};
+#define FBIOGTYPE _IOR('F', 0, struct fbtype)
+
+struct fbcmap {
+ int index; /* first element (0 origin) */
+ int count;
+ unsigned char __user *red;
+ unsigned char __user *green;
+ unsigned char __user *blue;
+};
+
+#ifdef __KERNEL__
+#define FBIOPUTCMAP_SPARC _IOW('F', 3, struct fbcmap)
+#define FBIOGETCMAP_SPARC _IOW('F', 4, struct fbcmap)
+#else
+#define FBIOPUTCMAP _IOW('F', 3, struct fbcmap)
+#define FBIOGETCMAP _IOW('F', 4, struct fbcmap)
+#endif
+
+/* # of device specific values */
+#define FB_ATTR_NDEVSPECIFIC 8
+/* # of possible emulations */
+#define FB_ATTR_NEMUTYPES 4
+
+struct fbsattr {
+ int flags;
+ int emu_type; /* -1 if none */
+ int dev_specific[FB_ATTR_NDEVSPECIFIC];
+};
+
+struct fbgattr {
+ int real_type; /* real frame buffer type */
+ int owner; /* unknown */
+ struct fbtype fbtype; /* real frame buffer fbtype */
+ struct fbsattr sattr;
+ int emu_types[FB_ATTR_NEMUTYPES]; /* supported emulations */
+};
+#define FBIOSATTR _IOW('F', 5, struct fbgattr) /* Unsupported: */
+#define FBIOGATTR _IOR('F', 6, struct fbgattr) /* supported */
+
+#define FBIOSVIDEO _IOW('F', 7, int)
+#define FBIOGVIDEO _IOR('F', 8, int)
+
+struct fbcursor {
+ short set; /* what to set, choose from the list above */
+ short enable; /* cursor on/off */
+ struct fbcurpos pos; /* cursor position */
+ struct fbcurpos hot; /* cursor hot spot */
+ struct fbcmap cmap; /* color map info */
+ struct fbcurpos size; /* cursor bit map size */
+ char __user *image; /* cursor image bits */
+ char __user *mask; /* cursor mask bits */
+};
+
+/* set/get cursor attributes/shape */
+#define FBIOSCURSOR _IOW('F', 24, struct fbcursor)
+#define FBIOGCURSOR _IOWR('F', 25, struct fbcursor)
+
+/* set/get cursor position */
+#define FBIOSCURPOS _IOW('F', 26, struct fbcurpos)
+#define FBIOGCURPOS _IOW('F', 27, struct fbcurpos)
+
+/* get max cursor size */
+#define FBIOGCURMAX _IOR('F', 28, struct fbcurpos)
+
+/* wid manipulation */
+struct fb_wid_alloc {
+#define FB_WID_SHARED_8 0
+#define FB_WID_SHARED_24 1
+#define FB_WID_DBL_8 2
+#define FB_WID_DBL_24 3
+ __u32 wa_type;
+ __s32 wa_index; /* Set on return */
+ __u32 wa_count;
+};
+struct fb_wid_item {
+ __u32 wi_type;
+ __s32 wi_index;
+ __u32 wi_attrs;
+ __u32 wi_values[32];
+};
+struct fb_wid_list {
+ __u32 wl_flags;
+ __u32 wl_count;
+ struct fb_wid_item *wl_list;
+};
+
+#define FBIO_WID_ALLOC _IOWR('F', 30, struct fb_wid_alloc)
+#define FBIO_WID_FREE _IOW('F', 31, struct fb_wid_alloc)
+#define FBIO_WID_PUT _IOW('F', 32, struct fb_wid_list)
+#define FBIO_WID_GET _IOWR('F', 33, struct fb_wid_list)
+
+/* Creator ioctls */
+#define FFB_IOCTL ('F'<<8)
+#define FFB_SYS_INFO (FFB_IOCTL|80)
+#define FFB_CLUTREAD (FFB_IOCTL|81)
+#define FFB_CLUTPOST (FFB_IOCTL|82)
+#define FFB_SETDIAGMODE (FFB_IOCTL|83)
+#define FFB_GETMONITORID (FFB_IOCTL|84)
+#define FFB_GETVIDEOMODE (FFB_IOCTL|85)
+#define FFB_SETVIDEOMODE (FFB_IOCTL|86)
+#define FFB_SETSERVER (FFB_IOCTL|87)
+#define FFB_SETOVCTL (FFB_IOCTL|88)
+#define FFB_GETOVCTL (FFB_IOCTL|89)
+#define FFB_GETSAXNUM (FFB_IOCTL|90)
+#define FFB_FBDEBUG (FFB_IOCTL|91)
+
+/* Cg14 ioctls */
+#define MDI_IOCTL ('M'<<8)
+#define MDI_RESET (MDI_IOCTL|1)
+#define MDI_GET_CFGINFO (MDI_IOCTL|2)
+#define MDI_SET_PIXELMODE (MDI_IOCTL|3)
+# define MDI_32_PIX 32
+# define MDI_16_PIX 16
+# define MDI_8_PIX 8
+
+struct mdi_cfginfo {
+ int mdi_ncluts; /* Number of implemented CLUTs in this MDI */
+ int mdi_type; /* FBTYPE name */
+ int mdi_height; /* height */
+ int mdi_width; /* widht */
+ int mdi_size; /* available ram */
+ int mdi_mode; /* 8bpp, 16bpp or 32bpp */
+ int mdi_pixfreq; /* pixel clock (from PROM) */
+};
+
+/* SparcLinux specific ioctl for the MDI, should be replaced for
+ * the SET_XLUT/SET_CLUTn ioctls instead
+ */
+#define MDI_CLEAR_XLUT (MDI_IOCTL|9)
+
+/* leo & ffb ioctls */
+struct fb_clut_alloc {
+ __u32 clutid; /* Set on return */
+ __u32 flag;
+ __u32 index;
+};
+
+struct fb_clut {
+#define FB_CLUT_WAIT 0x00000001 /* Not yet implemented */
+ __u32 flag;
+ __u32 clutid;
+ __u32 offset;
+ __u32 count;
+ char * red;
+ char * green;
+ char * blue;
+};
+
+struct fb_clut32 {
+ __u32 flag;
+ __u32 clutid;
+ __u32 offset;
+ __u32 count;
+ __u32 red;
+ __u32 green;
+ __u32 blue;
+};
+
+#define LEO_CLUTALLOC _IOWR('L', 53, struct fb_clut_alloc)
+#define LEO_CLUTFREE _IOW('L', 54, struct fb_clut_alloc)
+#define LEO_CLUTREAD _IOW('L', 55, struct fb_clut)
+#define LEO_CLUTPOST _IOW('L', 56, struct fb_clut)
+#define LEO_SETGAMMA _IOW('L', 68, int) /* Not yet implemented */
+#define LEO_GETGAMMA _IOR('L', 69, int) /* Not yet implemented */
+
+#ifdef __KERNEL__
+/* Addresses on the fd of a cgsix that are mappable */
+#define CG6_FBC 0x70000000
+#define CG6_TEC 0x70001000
+#define CG6_BTREGS 0x70002000
+#define CG6_FHC 0x70004000
+#define CG6_THC 0x70005000
+#define CG6_ROM 0x70006000
+#define CG6_RAM 0x70016000
+#define CG6_DHC 0x80000000
+
+#define CG3_MMAP_OFFSET 0x4000000
+
+/* Addresses on the fd of a tcx that are mappable */
+#define TCX_RAM8BIT 0x00000000
+#define TCX_RAM24BIT 0x01000000
+#define TCX_UNK3 0x10000000
+#define TCX_UNK4 0x20000000
+#define TCX_CONTROLPLANE 0x28000000
+#define TCX_UNK6 0x30000000
+#define TCX_UNK7 0x38000000
+#define TCX_TEC 0x70000000
+#define TCX_BTREGS 0x70002000
+#define TCX_THC 0x70004000
+#define TCX_DHC 0x70008000
+#define TCX_ALT 0x7000a000
+#define TCX_SYNC 0x7000e000
+#define TCX_UNK2 0x70010000
+
+/* CG14 definitions */
+
+/* Offsets into the OBIO space: */
+#define CG14_REGS 0 /* registers */
+#define CG14_CURSORREGS 0x1000 /* cursor registers */
+#define CG14_DACREGS 0x2000 /* DAC registers */
+#define CG14_XLUT 0x3000 /* X Look Up Table -- ??? */
+#define CG14_CLUT1 0x4000 /* Color Look Up Table */
+#define CG14_CLUT2 0x5000 /* Color Look Up Table */
+#define CG14_CLUT3 0x6000 /* Color Look Up Table */
+#define CG14_AUTO 0xf000
+
+#endif /* KERNEL */
+
+/* These are exported to userland for applications to use */
+/* Mappable offsets for the cg14: control registers */
+#define MDI_DIRECT_MAP 0x10000000
+#define MDI_CTLREG_MAP 0x20000000
+#define MDI_CURSOR_MAP 0x30000000
+#define MDI_SHDW_VRT_MAP 0x40000000
+
+/* Mappable offsets for the cg14: frame buffer resolutions */
+/* 32 bits */
+#define MDI_CHUNKY_XBGR_MAP 0x50000000
+#define MDI_CHUNKY_BGR_MAP 0x60000000
+
+/* 16 bits */
+#define MDI_PLANAR_X16_MAP 0x70000000
+#define MDI_PLANAR_C16_MAP 0x80000000
+
+/* 8 bit is done as CG3 MMAP offset */
+/* 32 bits, planar */
+#define MDI_PLANAR_X32_MAP 0x90000000
+#define MDI_PLANAR_B32_MAP 0xa0000000
+#define MDI_PLANAR_G32_MAP 0xb0000000
+#define MDI_PLANAR_R32_MAP 0xc0000000
+
+/* Mappable offsets on leo */
+#define LEO_SS0_MAP 0x00000000
+#define LEO_LC_SS0_USR_MAP 0x00800000
+#define LEO_LD_SS0_MAP 0x00801000
+#define LEO_LX_CURSOR_MAP 0x00802000
+#define LEO_SS1_MAP 0x00803000
+#define LEO_LC_SS1_USR_MAP 0x01003000
+#define LEO_LD_SS1_MAP 0x01004000
+#define LEO_UNK_MAP 0x01005000
+#define LEO_LX_KRN_MAP 0x01006000
+#define LEO_LC_SS0_KRN_MAP 0x01007000
+#define LEO_LC_SS1_KRN_MAP 0x01008000
+#define LEO_LD_GBL_MAP 0x01009000
+#define LEO_UNK2_MAP 0x0100a000
+
+#ifdef __KERNEL__
+struct fbcmap32 {
+ int index; /* first element (0 origin) */
+ int count;
+ u32 red;
+ u32 green;
+ u32 blue;
+};
+
+#define FBIOPUTCMAP32 _IOW('F', 3, struct fbcmap32)
+#define FBIOGETCMAP32 _IOW('F', 4, struct fbcmap32)
+
+struct fbcursor32 {
+ short set; /* what to set, choose from the list above */
+ short enable; /* cursor on/off */
+ struct fbcurpos pos; /* cursor position */
+ struct fbcurpos hot; /* cursor hot spot */
+ struct fbcmap32 cmap; /* color map info */
+ struct fbcurpos size; /* cursor bit map size */
+ u32 image; /* cursor image bits */
+ u32 mask; /* cursor mask bits */
+};
+
+#define FBIOSCURSOR32 _IOW('F', 24, struct fbcursor32)
+#define FBIOGCURSOR32 _IOW('F', 25, struct fbcursor32)
+#endif
+
+#endif /* __LINUX_FBIO_H */
#ifndef _M68K_IDPROM_H
#define _M68K_IDPROM_H
-#include <asm-sparc/idprom.h>
+/*
+ * idprom.h: Macros and defines for idprom routines
+ *
+ * Copyright (C) 1995,1996 David S. Miller (davem@caip.rutgers.edu)
+ */
+
+#include <linux/types.h>
+
+struct idprom {
+ u8 id_format; /* Format identifier (always 0x01) */
+ u8 id_machtype; /* Machine type */
+ u8 id_ethaddr[6]; /* Hardware ethernet address */
+ s32 id_date; /* Date of manufacture */
+ u32 id_sernum:24; /* Unique serial number */
+ u8 id_cksum; /* Checksum - xor of the data bytes */
+ u8 reserved[16];
+};
+
+extern struct idprom *idprom;
+extern void idprom_init(void);
/* Sun3: in control space */
#define SUN3_IDPROM_BASE 0x00000000
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1995 Andreas Busse
- * Copyright (C) 2003 Ralf Baechle
- */
-#ifndef _ASM_GDB_STUB_H
-#define _ASM_GDB_STUB_H
-
-
-/*
- * important register numbers
- */
-
-#define REG_EPC 37
-#define REG_FP 72
-#define REG_SP 29
-
-/*
- * Stack layout for the GDB exception handler
- * Derived from the stack layout described in asm-mips/stackframe.h
- *
- * The first PTRSIZE*6 bytes are argument save space for C subroutines.
- */
-#define NUMREGS 90
-
-#define GDB_FR_REG0 (PTRSIZE*6) /* 0 */
-#define GDB_FR_REG1 ((GDB_FR_REG0) + LONGSIZE) /* 1 */
-#define GDB_FR_REG2 ((GDB_FR_REG1) + LONGSIZE) /* 2 */
-#define GDB_FR_REG3 ((GDB_FR_REG2) + LONGSIZE) /* 3 */
-#define GDB_FR_REG4 ((GDB_FR_REG3) + LONGSIZE) /* 4 */
-#define GDB_FR_REG5 ((GDB_FR_REG4) + LONGSIZE) /* 5 */
-#define GDB_FR_REG6 ((GDB_FR_REG5) + LONGSIZE) /* 6 */
-#define GDB_FR_REG7 ((GDB_FR_REG6) + LONGSIZE) /* 7 */
-#define GDB_FR_REG8 ((GDB_FR_REG7) + LONGSIZE) /* 8 */
-#define GDB_FR_REG9 ((GDB_FR_REG8) + LONGSIZE) /* 9 */
-#define GDB_FR_REG10 ((GDB_FR_REG9) + LONGSIZE) /* 10 */
-#define GDB_FR_REG11 ((GDB_FR_REG10) + LONGSIZE) /* 11 */
-#define GDB_FR_REG12 ((GDB_FR_REG11) + LONGSIZE) /* 12 */
-#define GDB_FR_REG13 ((GDB_FR_REG12) + LONGSIZE) /* 13 */
-#define GDB_FR_REG14 ((GDB_FR_REG13) + LONGSIZE) /* 14 */
-#define GDB_FR_REG15 ((GDB_FR_REG14) + LONGSIZE) /* 15 */
-#define GDB_FR_REG16 ((GDB_FR_REG15) + LONGSIZE) /* 16 */
-#define GDB_FR_REG17 ((GDB_FR_REG16) + LONGSIZE) /* 17 */
-#define GDB_FR_REG18 ((GDB_FR_REG17) + LONGSIZE) /* 18 */
-#define GDB_FR_REG19 ((GDB_FR_REG18) + LONGSIZE) /* 19 */
-#define GDB_FR_REG20 ((GDB_FR_REG19) + LONGSIZE) /* 20 */
-#define GDB_FR_REG21 ((GDB_FR_REG20) + LONGSIZE) /* 21 */
-#define GDB_FR_REG22 ((GDB_FR_REG21) + LONGSIZE) /* 22 */
-#define GDB_FR_REG23 ((GDB_FR_REG22) + LONGSIZE) /* 23 */
-#define GDB_FR_REG24 ((GDB_FR_REG23) + LONGSIZE) /* 24 */
-#define GDB_FR_REG25 ((GDB_FR_REG24) + LONGSIZE) /* 25 */
-#define GDB_FR_REG26 ((GDB_FR_REG25) + LONGSIZE) /* 26 */
-#define GDB_FR_REG27 ((GDB_FR_REG26) + LONGSIZE) /* 27 */
-#define GDB_FR_REG28 ((GDB_FR_REG27) + LONGSIZE) /* 28 */
-#define GDB_FR_REG29 ((GDB_FR_REG28) + LONGSIZE) /* 29 */
-#define GDB_FR_REG30 ((GDB_FR_REG29) + LONGSIZE) /* 30 */
-#define GDB_FR_REG31 ((GDB_FR_REG30) + LONGSIZE) /* 31 */
-
-/*
- * Saved special registers
- */
-#define GDB_FR_STATUS ((GDB_FR_REG31) + LONGSIZE) /* 32 */
-#define GDB_FR_LO ((GDB_FR_STATUS) + LONGSIZE) /* 33 */
-#define GDB_FR_HI ((GDB_FR_LO) + LONGSIZE) /* 34 */
-#define GDB_FR_BADVADDR ((GDB_FR_HI) + LONGSIZE) /* 35 */
-#define GDB_FR_CAUSE ((GDB_FR_BADVADDR) + LONGSIZE) /* 36 */
-#define GDB_FR_EPC ((GDB_FR_CAUSE) + LONGSIZE) /* 37 */
-
-/*
- * Saved floating point registers
- */
-#define GDB_FR_FPR0 ((GDB_FR_EPC) + LONGSIZE) /* 38 */
-#define GDB_FR_FPR1 ((GDB_FR_FPR0) + LONGSIZE) /* 39 */
-#define GDB_FR_FPR2 ((GDB_FR_FPR1) + LONGSIZE) /* 40 */
-#define GDB_FR_FPR3 ((GDB_FR_FPR2) + LONGSIZE) /* 41 */
-#define GDB_FR_FPR4 ((GDB_FR_FPR3) + LONGSIZE) /* 42 */
-#define GDB_FR_FPR5 ((GDB_FR_FPR4) + LONGSIZE) /* 43 */
-#define GDB_FR_FPR6 ((GDB_FR_FPR5) + LONGSIZE) /* 44 */
-#define GDB_FR_FPR7 ((GDB_FR_FPR6) + LONGSIZE) /* 45 */
-#define GDB_FR_FPR8 ((GDB_FR_FPR7) + LONGSIZE) /* 46 */
-#define GDB_FR_FPR9 ((GDB_FR_FPR8) + LONGSIZE) /* 47 */
-#define GDB_FR_FPR10 ((GDB_FR_FPR9) + LONGSIZE) /* 48 */
-#define GDB_FR_FPR11 ((GDB_FR_FPR10) + LONGSIZE) /* 49 */
-#define GDB_FR_FPR12 ((GDB_FR_FPR11) + LONGSIZE) /* 50 */
-#define GDB_FR_FPR13 ((GDB_FR_FPR12) + LONGSIZE) /* 51 */
-#define GDB_FR_FPR14 ((GDB_FR_FPR13) + LONGSIZE) /* 52 */
-#define GDB_FR_FPR15 ((GDB_FR_FPR14) + LONGSIZE) /* 53 */
-#define GDB_FR_FPR16 ((GDB_FR_FPR15) + LONGSIZE) /* 54 */
-#define GDB_FR_FPR17 ((GDB_FR_FPR16) + LONGSIZE) /* 55 */
-#define GDB_FR_FPR18 ((GDB_FR_FPR17) + LONGSIZE) /* 56 */
-#define GDB_FR_FPR19 ((GDB_FR_FPR18) + LONGSIZE) /* 57 */
-#define GDB_FR_FPR20 ((GDB_FR_FPR19) + LONGSIZE) /* 58 */
-#define GDB_FR_FPR21 ((GDB_FR_FPR20) + LONGSIZE) /* 59 */
-#define GDB_FR_FPR22 ((GDB_FR_FPR21) + LONGSIZE) /* 60 */
-#define GDB_FR_FPR23 ((GDB_FR_FPR22) + LONGSIZE) /* 61 */
-#define GDB_FR_FPR24 ((GDB_FR_FPR23) + LONGSIZE) /* 62 */
-#define GDB_FR_FPR25 ((GDB_FR_FPR24) + LONGSIZE) /* 63 */
-#define GDB_FR_FPR26 ((GDB_FR_FPR25) + LONGSIZE) /* 64 */
-#define GDB_FR_FPR27 ((GDB_FR_FPR26) + LONGSIZE) /* 65 */
-#define GDB_FR_FPR28 ((GDB_FR_FPR27) + LONGSIZE) /* 66 */
-#define GDB_FR_FPR29 ((GDB_FR_FPR28) + LONGSIZE) /* 67 */
-#define GDB_FR_FPR30 ((GDB_FR_FPR29) + LONGSIZE) /* 68 */
-#define GDB_FR_FPR31 ((GDB_FR_FPR30) + LONGSIZE) /* 69 */
-
-#define GDB_FR_FSR ((GDB_FR_FPR31) + LONGSIZE) /* 70 */
-#define GDB_FR_FIR ((GDB_FR_FSR) + LONGSIZE) /* 71 */
-#define GDB_FR_FRP ((GDB_FR_FIR) + LONGSIZE) /* 72 */
-
-#define GDB_FR_DUMMY ((GDB_FR_FRP) + LONGSIZE) /* 73, unused ??? */
-
-/*
- * Again, CP0 registers
- */
-#define GDB_FR_CP0_INDEX ((GDB_FR_DUMMY) + LONGSIZE) /* 74 */
-#define GDB_FR_CP0_RANDOM ((GDB_FR_CP0_INDEX) + LONGSIZE) /* 75 */
-#define GDB_FR_CP0_ENTRYLO0 ((GDB_FR_CP0_RANDOM) + LONGSIZE)/* 76 */
-#define GDB_FR_CP0_ENTRYLO1 ((GDB_FR_CP0_ENTRYLO0) + LONGSIZE)/* 77 */
-#define GDB_FR_CP0_CONTEXT ((GDB_FR_CP0_ENTRYLO1) + LONGSIZE)/* 78 */
-#define GDB_FR_CP0_PAGEMASK ((GDB_FR_CP0_CONTEXT) + LONGSIZE)/* 79 */
-#define GDB_FR_CP0_WIRED ((GDB_FR_CP0_PAGEMASK) + LONGSIZE)/* 80 */
-#define GDB_FR_CP0_REG7 ((GDB_FR_CP0_WIRED) + LONGSIZE) /* 81 */
-#define GDB_FR_CP0_REG8 ((GDB_FR_CP0_REG7) + LONGSIZE) /* 82 */
-#define GDB_FR_CP0_REG9 ((GDB_FR_CP0_REG8) + LONGSIZE) /* 83 */
-#define GDB_FR_CP0_ENTRYHI ((GDB_FR_CP0_REG9) + LONGSIZE) /* 84 */
-#define GDB_FR_CP0_REG11 ((GDB_FR_CP0_ENTRYHI) + LONGSIZE)/* 85 */
-#define GDB_FR_CP0_REG12 ((GDB_FR_CP0_REG11) + LONGSIZE) /* 86 */
-#define GDB_FR_CP0_REG13 ((GDB_FR_CP0_REG12) + LONGSIZE) /* 87 */
-#define GDB_FR_CP0_REG14 ((GDB_FR_CP0_REG13) + LONGSIZE) /* 88 */
-#define GDB_FR_CP0_PRID ((GDB_FR_CP0_REG14) + LONGSIZE) /* 89 */
-
-#define GDB_FR_SIZE ((((GDB_FR_CP0_PRID) + LONGSIZE) + (PTRSIZE-1)) & ~(PTRSIZE-1))
-
-#ifndef __ASSEMBLY__
-
-/*
- * This is the same as above, but for the high-level
- * part of the GDB stub.
- */
-
-struct gdb_regs {
- /*
- * Pad bytes for argument save space on the stack
- * 24/48 Bytes for 32/64 bit code
- */
- unsigned long pad0[6];
-
- /*
- * saved main processor registers
- */
- long reg0, reg1, reg2, reg3, reg4, reg5, reg6, reg7;
- long reg8, reg9, reg10, reg11, reg12, reg13, reg14, reg15;
- long reg16, reg17, reg18, reg19, reg20, reg21, reg22, reg23;
- long reg24, reg25, reg26, reg27, reg28, reg29, reg30, reg31;
-
- /*
- * Saved special registers
- */
- long cp0_status;
- long lo;
- long hi;
- long cp0_badvaddr;
- long cp0_cause;
- long cp0_epc;
-
- /*
- * Saved floating point registers
- */
- long fpr0, fpr1, fpr2, fpr3, fpr4, fpr5, fpr6, fpr7;
- long fpr8, fpr9, fpr10, fpr11, fpr12, fpr13, fpr14, fpr15;
- long fpr16, fpr17, fpr18, fpr19, fpr20, fpr21, fpr22, fpr23;
- long fpr24, fpr25, fpr26, fpr27, fpr28, fpr29, fpr30, fpr31;
-
- long cp1_fsr;
- long cp1_fir;
-
- /*
- * Frame pointer
- */
- long frame_ptr;
- long dummy; /* unused */
-
- /*
- * saved cp0 registers
- */
- long cp0_index;
- long cp0_random;
- long cp0_entrylo0;
- long cp0_entrylo1;
- long cp0_context;
- long cp0_pagemask;
- long cp0_wired;
- long cp0_reg7;
- long cp0_reg8;
- long cp0_reg9;
- long cp0_entryhi;
- long cp0_reg11;
- long cp0_reg12;
- long cp0_reg13;
- long cp0_reg14;
- long cp0_prid;
-};
-
-/*
- * Prototypes
- */
-
-extern int kgdb_enabled;
-void set_debug_traps(void);
-void set_async_breakpoint(unsigned long *epc);
-
-#endif /* !__ASSEMBLY__ */
-#endif /* _ASM_GDB_STUB_H */
-#include <asm-generic/kdebug.h>
+#ifndef _ASM_MIPS_KDEBUG_H
+#define _ASM_MIPS_KDEBUG_H
+
+#include <linux/notifier.h>
+
+enum die_val {
+ DIE_OOPS = 1,
+ DIE_FP,
+ DIE_TRAP,
+ DIE_RI,
+};
+
+#endif /* _ASM_MIPS_KDEBUG_H */
--- /dev/null
+#ifndef __ASM_KGDB_H_
+#define __ASM_KGDB_H_
+
+#ifdef __KERNEL__
+
+#include <asm/sgidefs.h>
+
+#if (_MIPS_ISA == _MIPS_ISA_MIPS1) || (_MIPS_ISA == _MIPS_ISA_MIPS2) || \
+ (_MIPS_ISA == _MIPS_ISA_MIPS32)
+
+#define KGDB_GDB_REG_SIZE 32
+
+#elif (_MIPS_ISA == _MIPS_ISA_MIPS3) || (_MIPS_ISA == _MIPS_ISA_MIPS4) || \
+ (_MIPS_ISA == _MIPS_ISA_MIPS64)
+
+#ifdef CONFIG_32BIT
+#define KGDB_GDB_REG_SIZE 32
+#else /* CONFIG_CPU_32BIT */
+#define KGDB_GDB_REG_SIZE 64
+#endif
+#else
+#error "Need to set KGDB_GDB_REG_SIZE for MIPS ISA"
+#endif /* _MIPS_ISA */
+
+#define BUFMAX 2048
+#if (KGDB_GDB_REG_SIZE == 32)
+#define NUMREGBYTES (90*sizeof(u32))
+#define NUMCRITREGBYTES (12*sizeof(u32))
+#else
+#define NUMREGBYTES (90*sizeof(u64))
+#define NUMCRITREGBYTES (12*sizeof(u64))
+#endif
+#define BREAK_INSTR_SIZE 4
+#define CACHE_FLUSH_IS_SAFE 0
+
+extern void arch_kgdb_breakpoint(void);
+extern int kgdb_early_setup;
+extern void *saved_vectors[32];
+extern void handle_exception(struct pt_regs *regs);
+extern void breakinst(void);
+
+#endif /* __KERNEL__ */
+
+#endif /* __ASM_KGDB_H_ */
extern int pci_probe_only;
+extern char * (*pcibios_plat_setup)(char *str);
+
#endif /* _ASM_PCI_H */
extern int (*txx9_irq_dispatch)(int pending);
void prom_init_cmdline(void);
char *prom_getcmdline(void);
+void txx9_wdt_init(unsigned long base);
+void txx9_spi_init(int busid, unsigned long base, int irq);
+void txx9_ethaddr_init(unsigned int id, unsigned char *ethaddr);
+void txx9_sio_init(unsigned long baseaddr, int irq,
+ unsigned int line, unsigned int sclk, int nocts);
+void prom_putchar(char c);
+#ifdef CONFIG_EARLY_PRINTK
+extern void (*txx9_prom_putchar)(char c);
+void txx9_sio_putchar_init(unsigned long baseaddr);
+#else
+static inline void txx9_sio_putchar_init(unsigned long baseaddr)
+{
+}
+#endif
#endif /* __ASM_TXX9_GENERIC_H */
/* Clocks */
#define JMR3927_CORECLK 132710400 /* 132.7MHz */
-#define JMR3927_GBUSCLK (JMR3927_CORECLK / 2) /* 66.35MHz */
-#define JMR3927_IMCLK (JMR3927_CORECLK / 4) /* 33.17MHz */
/*
* TX3927 Pin Configuration:
};
extern enum txx9_pci_err_action txx9_pci_err_action;
+extern char * (*txx9_board_pcibios_setup)(char *str);
+char *txx9_pcibios_setup(char *str);
+
#endif /* __ASM_TXX9_PCI_H */
#define SMSC_FDC37M81X_CONFIG_EXIT 0xaa
#define SMSC_FDC37M81X_CHIP_ID 0x4d
-unsigned long __init smsc_fdc37m81x_init(unsigned long port);
+unsigned long smsc_fdc37m81x_init(unsigned long port);
void smsc_fdc37m81x_config_beg(void);
#ifndef __ASM_TXX9_TX3927_H
#define __ASM_TXX9_TX3927_H
-#include <asm/txx9/txx927.h>
-
#define TX3927_REG_BASE 0xfffe0000UL
+#define TX3927_REG_SIZE 0x00010000
#define TX3927_SDRAMC_REG (TX3927_REG_BASE + 0x8000)
#define TX3927_ROMC_REG (TX3927_REG_BASE + 0x9000)
#define TX3927_DMA_REG (TX3927_REG_BASE + 0xb000)
/* see PCI_STATUS_XXX in linux/pci.h */
#define PCI_STATUS_NEW_CAP 0x0010
+/* bits for ISTAT/IIM */
+#define TX3927_PCIC_IIM_ALL 0x00001600
+
/* bits for TC */
#define TX3927_PCIC_TC_OF16E 0x00000020
#define TX3927_PCIC_TC_IF8E 0x00000010
#define TX3927_PCIC_TC_OF8E 0x00000008
+/* bits for TSTAT/TIM */
+#define TX3927_PCIC_TIM_ALL 0x0003ffff
+
/* bits for IOBA/MBA */
/* see PCI_BASE_ADDRESS_XXX in linux/pci.h */
#define tx3927_dmaptr ((struct tx3927_dma_reg *)TX3927_DMA_REG)
#define tx3927_pcicptr ((struct tx3927_pcic_reg *)TX3927_PCIC_REG)
#define tx3927_ccfgptr ((struct tx3927_ccfg_reg *)TX3927_CCFG_REG)
-#define tx3927_tmrptr(ch) ((struct txx927_tmr_reg *)TX3927_TMR_REG(ch))
#define tx3927_sioptr(ch) ((struct txx927_sio_reg *)TX3927_SIO_REG(ch))
#define tx3927_pioptr ((struct txx9_pio_reg __iomem *)TX3927_PIO_REG)
+#define TX3927_REV_PCODE() (tx3927_ccfgptr->crir >> 16)
+#define TX3927_ROMC_BA(ch) (tx3927_romcptr->cr[(ch)] & 0xfff00000)
+#define TX3927_ROMC_SIZE(ch) \
+ (0x00100000 << ((tx3927_romcptr->cr[(ch)] >> 8) & 0xf))
+
+void tx3927_wdt_init(void);
+void tx3927_setup(void);
+void tx3927_time_init(unsigned int evt_tmrnr, unsigned int src_tmrnr);
+void tx3927_sio_init(unsigned int sclk, unsigned int cts_mask);
struct pci_controller;
-void __init tx3927_pcic_setup(struct pci_controller *channel,
- unsigned long sdram_size, int extarb);
+void tx3927_pcic_setup(struct pci_controller *channel,
+ unsigned long sdram_size, int extarb);
+void tx3927_setup_pcierr_irq(void);
+void tx3927_irq_init(void);
#endif /* __ASM_TXX9_TX3927_H */
}
unsigned int tx4927_get_mem_size(void);
-void tx4927_wdr_init(void);
+void tx4927_wdt_init(void);
void tx4927_setup(void);
void tx4927_time_init(unsigned int tmrnr);
-void tx4927_setup_serial(void);
+void tx4927_sio_init(unsigned int sclk, unsigned int cts_mask);
int tx4927_report_pciclk(void);
int tx4927_pciclk66_setup(void);
+void tx4927_setup_pcierr_irq(void);
void tx4927_irq_init(void);
#endif /* __ASM_TXX9_TX4927_H */
#define __ASM_TXX9_TX4927PCIC_H
#include <linux/pci.h>
+#include <linux/irqreturn.h>
struct tx4927_pcic_reg {
u32 pciid;
struct tx4927_pcic_reg __iomem *get_tx4927_pcicptr(
struct pci_controller *channel);
-void __init tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
- struct pci_controller *channel, int extarb);
+void tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
+ struct pci_controller *channel, int extarb);
void tx4927_report_pcic_status(void);
+char *tx4927_pcibios_setup(char *str);
+void tx4927_dump_pcic_settings(void);
+irqreturn_t tx4927_pcierr_interrupt(int irq, void *dev_id);
#endif /* __ASM_TXX9_TX4927PCIC_H */
#define TX4938_EBUSC_SIZE(ch) TX4927_EBUSC_SIZE(ch)
#define tx4938_get_mem_size() tx4927_get_mem_size()
-void tx4938_wdr_init(void);
+void tx4938_wdt_init(void);
void tx4938_setup(void);
void tx4938_time_init(unsigned int tmrnr);
-void tx4938_setup_serial(void);
+void tx4938_sio_init(unsigned int sclk, unsigned int cts_mask);
+void tx4938_spi_init(int busid);
+void tx4938_ethaddr_init(unsigned char *addr0, unsigned char *addr1);
int tx4938_report_pciclk(void);
void tx4938_report_pci1clk(void);
int tx4938_pciclk66_setup(void);
struct pci_dev;
int tx4938_pcic1_map_irq(const struct pci_dev *dev, u8 slot);
+void tx4938_setup_pcierr_irq(void);
void tx4938_irq_init(void);
#endif
+++ /dev/null
-/*
- * Common definitions for TX3927/TX4927
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2000 Toshiba Corporation
- */
-#ifndef __ASM_TXX9_TXX927_H
-#define __ASM_TXX9_TXX927_H
-
-struct txx927_sio_reg {
- volatile unsigned long lcr;
- volatile unsigned long dicr;
- volatile unsigned long disr;
- volatile unsigned long cisr;
- volatile unsigned long fcr;
- volatile unsigned long flcr;
- volatile unsigned long bgr;
- volatile unsigned long tfifo;
- volatile unsigned long rfifo;
-};
-
-/*
- * SIO
- */
-/* SILCR : Line Control */
-#define TXx927_SILCR_SCS_MASK 0x00000060
-#define TXx927_SILCR_SCS_IMCLK 0x00000000
-#define TXx927_SILCR_SCS_IMCLK_BG 0x00000020
-#define TXx927_SILCR_SCS_SCLK 0x00000040
-#define TXx927_SILCR_SCS_SCLK_BG 0x00000060
-#define TXx927_SILCR_UEPS 0x00000010
-#define TXx927_SILCR_UPEN 0x00000008
-#define TXx927_SILCR_USBL_MASK 0x00000004
-#define TXx927_SILCR_USBL_1BIT 0x00000004
-#define TXx927_SILCR_USBL_2BIT 0x00000000
-#define TXx927_SILCR_UMODE_MASK 0x00000003
-#define TXx927_SILCR_UMODE_8BIT 0x00000000
-#define TXx927_SILCR_UMODE_7BIT 0x00000001
-
-/* SIDICR : DMA/Int. Control */
-#define TXx927_SIDICR_TDE 0x00008000
-#define TXx927_SIDICR_RDE 0x00004000
-#define TXx927_SIDICR_TIE 0x00002000
-#define TXx927_SIDICR_RIE 0x00001000
-#define TXx927_SIDICR_SPIE 0x00000800
-#define TXx927_SIDICR_CTSAC 0x00000600
-#define TXx927_SIDICR_STIE_MASK 0x0000003f
-#define TXx927_SIDICR_STIE_OERS 0x00000020
-#define TXx927_SIDICR_STIE_CTSS 0x00000010
-#define TXx927_SIDICR_STIE_RBRKD 0x00000008
-#define TXx927_SIDICR_STIE_TRDY 0x00000004
-#define TXx927_SIDICR_STIE_TXALS 0x00000002
-#define TXx927_SIDICR_STIE_UBRKD 0x00000001
-
-/* SIDISR : DMA/Int. Status */
-#define TXx927_SIDISR_UBRK 0x00008000
-#define TXx927_SIDISR_UVALID 0x00004000
-#define TXx927_SIDISR_UFER 0x00002000
-#define TXx927_SIDISR_UPER 0x00001000
-#define TXx927_SIDISR_UOER 0x00000800
-#define TXx927_SIDISR_ERI 0x00000400
-#define TXx927_SIDISR_TOUT 0x00000200
-#define TXx927_SIDISR_TDIS 0x00000100
-#define TXx927_SIDISR_RDIS 0x00000080
-#define TXx927_SIDISR_STIS 0x00000040
-#define TXx927_SIDISR_RFDN_MASK 0x0000001f
-
-/* SICISR : Change Int. Status */
-#define TXx927_SICISR_OERS 0x00000020
-#define TXx927_SICISR_CTSS 0x00000010
-#define TXx927_SICISR_RBRKD 0x00000008
-#define TXx927_SICISR_TRDY 0x00000004
-#define TXx927_SICISR_TXALS 0x00000002
-#define TXx927_SICISR_UBRKD 0x00000001
-
-/* SIFCR : FIFO Control */
-#define TXx927_SIFCR_SWRST 0x00008000
-#define TXx927_SIFCR_RDIL_MASK 0x00000180
-#define TXx927_SIFCR_RDIL_1 0x00000000
-#define TXx927_SIFCR_RDIL_4 0x00000080
-#define TXx927_SIFCR_RDIL_8 0x00000100
-#define TXx927_SIFCR_RDIL_12 0x00000180
-#define TXx927_SIFCR_RDIL_MAX 0x00000180
-#define TXx927_SIFCR_TDIL_MASK 0x00000018
-#define TXx927_SIFCR_TDIL_MASK 0x00000018
-#define TXx927_SIFCR_TDIL_1 0x00000000
-#define TXx927_SIFCR_TDIL_4 0x00000001
-#define TXx927_SIFCR_TDIL_8 0x00000010
-#define TXx927_SIFCR_TDIL_MAX 0x00000010
-#define TXx927_SIFCR_TFRST 0x00000004
-#define TXx927_SIFCR_RFRST 0x00000002
-#define TXx927_SIFCR_FRSTE 0x00000001
-#define TXx927_SIO_TX_FIFO 8
-#define TXx927_SIO_RX_FIFO 16
-
-/* SIFLCR : Flow Control */
-#define TXx927_SIFLCR_RCS 0x00001000
-#define TXx927_SIFLCR_TES 0x00000800
-#define TXx927_SIFLCR_RTSSC 0x00000200
-#define TXx927_SIFLCR_RSDE 0x00000100
-#define TXx927_SIFLCR_TSDE 0x00000080
-#define TXx927_SIFLCR_RTSTL_MASK 0x0000001e
-#define TXx927_SIFLCR_RTSTL_MAX 0x0000001e
-#define TXx927_SIFLCR_TBRK 0x00000001
-
-/* SIBGR : Baudrate Control */
-#define TXx927_SIBGR_BCLK_MASK 0x00000300
-#define TXx927_SIBGR_BCLK_T0 0x00000000
-#define TXx927_SIBGR_BCLK_T2 0x00000100
-#define TXx927_SIBGR_BCLK_T4 0x00000200
-#define TXx927_SIBGR_BCLK_T6 0x00000300
-#define TXx927_SIBGR_BRD_MASK 0x000000ff
-
-/*
- * PIO
- */
-
-#endif /* __ASM_TXX9_TXX927_H */
#ifdef CONFIG_IRQ_CPU
#define TXX9_IRQ_BASE (MIPS_CPU_IRQ_BASE + 8)
#else
+#ifdef CONFIG_I8259
+#define TXX9_IRQ_BASE (I8259A_IRQ_BASE + 16)
+#else
#define TXX9_IRQ_BASE 0
#endif
+#endif
#ifdef CONFIG_CPU_TX39XX
#define TXx9_MAX_IR 16
#define __NR_fallocate 325
#define __NR_timerfd_settime 326
#define __NR_timerfd_gettime 327
+#define __NR_signalfd4 328
+#define __NR_eventfd2 329
+#define __NR_epoll_create1 330
+#define __NR_dup3 331
+#define __NR_pipe2 332
+#define __NR_inotify_init1 333
#ifdef __KERNEL__
+++ /dev/null
-#ifndef __ASM_SH_A_OUT_H
-#define __ASM_SH_A_OUT_H
-
-struct exec
-{
- unsigned long a_info; /* Use macros N_MAGIC, etc for access */
- unsigned a_text; /* length of text, in bytes */
- unsigned a_data; /* length of data, in bytes */
- unsigned a_bss; /* length of uninitialized data area for file, in bytes */
- unsigned a_syms; /* length of symbol table data in file, in bytes */
- unsigned a_entry; /* start address */
- unsigned a_trsize; /* length of relocation info for text, in bytes */
- unsigned a_drsize; /* length of relocation info for data, in bytes */
-};
-
-#define N_TRSIZE(a) ((a).a_trsize)
-#define N_DRSIZE(a) ((a).a_drsize)
-#define N_SYMSIZE(a) ((a).a_syms)
-
-#endif /* __ASM_SH_A_OUT_H */
+++ /dev/null
-#include <asm/cpu-sh2/cacheflush.h>
+++ /dev/null
-#include <asm/cpu-sh2/dma.h>
+++ /dev/null
-#include <asm/cpu-sh2/mmu_context.h>
+++ /dev/null
-#include <asm/cpu-sh2/timer.h>
+++ /dev/null
-#include <asm/cpu-sh2/ubc.h>
+++ /dev/null
-#include <asm/cpu-sh2/watchdog.h>
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1999 by Kaz Kojima
- *
- * Defitions for the address spaces of the SH-3 CPUs.
- */
-#ifndef __ASM_CPU_SH3_ADDRSPACE_H
-#define __ASM_CPU_SH3_ADDRSPACE_H
-
-#define P0SEG 0x00000000
-#define P1SEG 0x80000000
-#define P2SEG 0xa0000000
-#define P3SEG 0xc0000000
-#define P4SEG 0xe0000000
-
-#endif /* __ASM_CPU_SH3_ADDRSPACE_H */
+++ /dev/null
-/*
- * include/asm-sh/cpu-sh3/cacheflush.h
- *
- * Copyright (C) 1999 Niibe Yutaka
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#ifndef __ASM_CPU_SH3_CACHEFLUSH_H
-#define __ASM_CPU_SH3_CACHEFLUSH_H
-
-/*
- * Cache flushing:
- *
- * - flush_cache_all() flushes entire cache
- * - flush_cache_mm(mm) flushes the specified mm context's cache lines
- * - flush_cache_dup mm(mm) handles cache flushing when forking
- * - flush_cache_page(mm, vmaddr, pfn) flushes a single page
- * - flush_cache_range(vma, start, end) flushes a range of pages
- *
- * - flush_dcache_page(pg) flushes(wback&invalidates) a page for dcache
- * - flush_icache_range(start, end) flushes(invalidates) a range for icache
- * - flush_icache_page(vma, pg) flushes(invalidates) a page for icache
- *
- * Caches are indexed (effectively) by physical address on SH-3, so
- * we don't need them.
- */
-
-#if defined(CONFIG_SH7705_CACHE_32KB)
-
-/* SH7705 is an SH3 processor with 32KB cache. This has alias issues like the
- * SH4. Unlike the SH4 this is a unified cache so we need to do some work
- * in mmap when 'exec'ing a new binary
- */
- /* 32KB cache, 4kb PAGE sizes need to check bit 12 */
-#define CACHE_ALIAS 0x00001000
-
-#define PG_mapped PG_arch_1
-
-void flush_cache_all(void);
-void flush_cache_mm(struct mm_struct *mm);
-#define flush_cache_dup_mm(mm) flush_cache_mm(mm)
-void flush_cache_range(struct vm_area_struct *vma, unsigned long start,
- unsigned long end);
-void flush_cache_page(struct vm_area_struct *vma, unsigned long addr, unsigned long pfn);
-void flush_dcache_page(struct page *pg);
-void flush_icache_range(unsigned long start, unsigned long end);
-void flush_icache_page(struct vm_area_struct *vma, struct page *page);
-#else
-#define flush_cache_all() do { } while (0)
-#define flush_cache_mm(mm) do { } while (0)
-#define flush_cache_dup_mm(mm) do { } while (0)
-#define flush_cache_range(vma, start, end) do { } while (0)
-#define flush_cache_page(vma, vmaddr, pfn) do { } while (0)
-#define flush_dcache_page(page) do { } while (0)
-#define flush_icache_range(start, end) do { } while (0)
-#define flush_icache_page(vma,pg) do { } while (0)
-#endif
-
-#define flush_dcache_mmap_lock(mapping) do { } while (0)
-#define flush_dcache_mmap_unlock(mapping) do { } while (0)
-
-/* SH3 has unified cache so no special action needed here */
-#define flush_cache_sigtramp(vaddr) do { } while (0)
-#define flush_icache_user_range(vma,pg,adr,len) do { } while (0)
-
-#define p3_cache_init() do { } while (0)
-
-#endif /* __ASM_CPU_SH3_CACHEFLUSH_H */
+++ /dev/null
-#ifndef __ASM_SH_CPU_SH3_RTC_H
-#define __ASM_SH_CPU_SH3_RTC_H
-
-#define rtc_reg_size sizeof(u16)
-#define RTC_BIT_INVERTED 0 /* No bug on SH7708, SH7709A */
-#define RTC_DEF_CAPABILITIES 0UL
-
-#endif /* __ASM_SH_CPU_SH3_RTC_H */
+++ /dev/null
-#ifndef __ASM_CPU_SH3_SIGCONTEXT_H
-#define __ASM_CPU_SH3_SIGCONTEXT_H
-
-struct sigcontext {
- unsigned long oldmask;
-
- /* CPU registers */
- unsigned long sc_regs[16];
- unsigned long sc_pc;
- unsigned long sc_pr;
- unsigned long sc_sr;
- unsigned long sc_gbr;
- unsigned long sc_mach;
- unsigned long sc_macl;
-};
-
-#endif /* __ASM_CPU_SH3_SIGCONTEXT_H */
+++ /dev/null
-#ifndef __ASM_SH_CPU_SH5_TIMER_H
-#define __ASM_SH_CPU_SH5_TIMER_H
-
-#endif /* __ASM_SH_CPU_SH5_TIMER_H */
extern int force_iommu, no_iommu;
extern int iommu_detected;
+extern unsigned long iommu_num_pages(unsigned long addr, unsigned long len);
+
#ifdef CONFIG_GART_IOMMU
extern int gart_iommu_aperture;
extern int gart_iommu_aperture_allowed;
#include <linux/types.h>
#include <linux/mm.h>
+#include <linux/mmu_notifier.h>
#include <linux/kvm.h>
#include <linux/kvm_para.h>
gfn_t gfn; /* presumed gfn during guest pte update */
pfn_t pfn; /* pfn corresponding to that gfn */
int largepage;
+ unsigned long mmu_seq;
} update_pte;
struct i387_fxsave_struct host_fx_image;
KVM_EX_ENTRY " 666b, 667b \n\t" \
".popsection"
+#define KVM_ARCH_WANT_MMU_NOTIFIER
+int kvm_unmap_hva(struct kvm *kvm, unsigned long hva);
+int kvm_age_hva(struct kvm *kvm, unsigned long hva);
+
#endif
header-y += ip6_tunnel.h
header-y += ipmi_msgdefs.h
header-y += ipsec.h
+header-y += ip_vs.h
header-y += ipx.h
header-y += irda.h
header-y += iso_fs.h
extern void blk_insert_request(struct request_queue *, struct request *, int, void *);
extern void blk_requeue_request(struct request_queue *, struct request *);
extern void blk_plug_device(struct request_queue *);
+extern void blk_plug_device_unlocked(struct request_queue *);
extern int blk_remove_plug(struct request_queue *);
extern void blk_recount_segments(struct request_queue *, struct bio *);
extern int scsi_cmd_ioctl(struct file *, struct request_queue *,
BUFFER_FNS(Dirty, dirty)
TAS_BUFFER_FNS(Dirty, dirty)
BUFFER_FNS(Lock, locked)
-TAS_BUFFER_FNS(Lock, locked)
BUFFER_FNS(Req, req)
TAS_BUFFER_FNS(Req, req)
BUFFER_FNS(Mapped, mapped)
__wait_on_buffer(bh);
}
+static inline int trylock_buffer(struct buffer_head *bh)
+{
+ return likely(!test_and_set_bit(BH_Lock, &bh->b_state));
+}
+
static inline void lock_buffer(struct buffer_head *bh)
{
might_sleep();
- if (test_set_buffer_locked(bh))
+ if (!trylock_buffer(bh))
__lock_buffer(bh);
}
#include <linux/list.h>
#include <linux/kref.h>
#include <linux/mutex.h>
+#include <linux/err.h>
#include <asm/atomic.h>
/*
* Users often need to create attribute structures for their configurable
* attributes, containing a configfs_attribute member and function pointers
- * for the show() and store() operations on that attribute. They can use
- * this macro (similar to sysfs' __ATTR) to make defining attributes easier.
+ * for the show() and store() operations on that attribute. If they don't
+ * need anything else on the extended attribute structure, they can use
+ * this macro to define it The argument _item is the name of the
+ * config_item structure.
+ */
+#define CONFIGFS_ATTR_STRUCT(_item) \
+struct _item##_attribute { \
+ struct configfs_attribute attr; \
+ ssize_t (*show)(struct _item *, char *); \
+ ssize_t (*store)(struct _item *, const char *, size_t); \
+}
+
+/*
+ * With the extended attribute structure, users can use this macro
+ * (similar to sysfs' __ATTR) to make defining attributes easier.
+ * An example:
+ * #define MYITEM_ATTR(_name, _mode, _show, _store) \
+ * struct myitem_attribute childless_attr_##_name = \
+ * __CONFIGFS_ATTR(_name, _mode, _show, _store)
*/
#define __CONFIGFS_ATTR(_name, _mode, _show, _store) \
{ \
.show = _show, \
.store = _store, \
}
+/* Here is a readonly version, only requiring a show() operation */
+#define __CONFIGFS_ATTR_RO(_name, _show) \
+{ \
+ .attr = { \
+ .ca_name = __stringify(_name), \
+ .ca_mode = 0444, \
+ .ca_owner = THIS_MODULE, \
+ }, \
+ .show = _show, \
+}
+
+/*
+ * With these extended attributes, the simple show_attribute() and
+ * store_attribute() operations need to call the show() and store() of the
+ * attributes. This is a common pattern, so we provide a macro to define
+ * them. The argument _item is the name of the config_item structure.
+ * This macro expects the attributes to be named "struct <name>_attribute"
+ * and the function to_<name>() to exist;
+ */
+#define CONFIGFS_ATTR_OPS(_item) \
+static ssize_t _item##_attr_show(struct config_item *item, \
+ struct configfs_attribute *attr, \
+ char *page) \
+{ \
+ struct _item *_item = to_##_item(item); \
+ struct _item##_attribute *_item##_attr = \
+ container_of(attr, struct _item##_attribute, attr); \
+ ssize_t ret = 0; \
+ \
+ if (_item##_attr->show) \
+ ret = _item##_attr->show(_item, page); \
+ return ret; \
+} \
+static ssize_t _item##_attr_store(struct config_item *item, \
+ struct configfs_attribute *attr, \
+ const char *page, size_t count) \
+{ \
+ struct _item *_item = to_##_item(item); \
+ struct _item##_attribute *_item##_attr = \
+ container_of(attr, struct _item##_attribute, attr); \
+ ssize_t ret = -EINVAL; \
+ \
+ if (_item##_attr->store) \
+ ret = _item##_attr->store(_item, page, count); \
+ return ret; \
+}
/*
* If allow_link() exists, the item can symlink(2) out to other
#define CN_W1_VAL 0x1
#define CN_IDX_V86D 0x4
#define CN_VAL_V86D_UVESAFB 0x1
+#define CN_IDX_BB 0x5 /* BlackBoard, from the TSP GPL sampling framework */
-#define CN_NETLINK_USERS 5
+#define CN_NETLINK_USERS 6
/*
* Maximum connector's message size.
#define CPUFREQ_ADJUST (0)
#define CPUFREQ_INCOMPATIBLE (1)
#define CPUFREQ_NOTIFY (2)
+#define CPUFREQ_START (3)
#define CPUFREQ_SHARED_TYPE_NONE (0) /* None */
#define CPUFREQ_SHARED_TYPE_HW (1) /* HW does needed coordination */
* gcc optimizes it out (it's a constant) and there's no huge stack
* variable created:
*/
-#define cpumask_of_cpu(cpu) ({ *get_cpu_mask(cpu); })
+#define cpumask_of_cpu(cpu) (*get_cpu_mask(cpu))
#define CPU_MASK_LAST_WORD BITMAP_LAST_WORD_MASK(NR_CPUS)
extern struct dentry * d_alloc(struct dentry *, const struct qstr *);
extern struct dentry * d_alloc_anon(struct inode *);
extern struct dentry * d_splice_alias(struct inode *, struct dentry *);
+extern struct dentry * d_add_ci(struct inode *, struct dentry *, struct qstr *);
extern void shrink_dcache_sb(struct super_block *);
extern void shrink_dcache_parent(struct dentry *);
extern void shrink_dcache_for_umount(struct super_block *);
struct dm9000_plat_data {
unsigned int flags;
+ unsigned char dev_addr[6];
/* allow replacement IO routines */
__u8 autoneg; /* Enable or disable autonegotiation */
__u32 maxtxpkt; /* Tx pkts before generating tx int */
__u32 maxrxpkt; /* Rx pkts before generating rx int */
- __u32 reserved[4];
+ __u16 speed_hi;
+ __u16 reserved2;
+ __u32 reserved[3];
};
+static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep,
+ __u32 speed)
+{
+
+ ep->speed = (__u16)speed;
+ ep->speed_hi = (__u16)(speed >> 16);
+}
+
+static inline __u32 ethtool_cmd_speed(struct ethtool_cmd *ep)
+{
+ return (ep->speed_hi << 16) | ep->speed;
+}
+
#define ETHTOOL_BUSINFO_LEN 32
/* these strings are set to whatever the driver author decides... */
struct ethtool_drvinfo {
extern struct file *fget_light(unsigned int fd, int *fput_needed);
extern void set_close_on_exec(unsigned int fd, int flag);
extern void put_filp(struct file *);
+extern int alloc_fd(unsigned start, unsigned flags);
extern int get_unused_fd(void);
-extern int get_unused_fd_flags(int flags);
+#define get_unused_fd_flags(flags) alloc_fd(0, (flags))
extern void put_unused_fd(unsigned int fd);
extern void fd_install(unsigned int fd, struct file *file);
#ifndef __I2C_PNX_H__
#define __I2C_PNX_H__
-#include <asm/arch/i2c.h>
+#include <linux/pm.h>
+
+struct platform_device;
struct i2c_pnx_mif {
int ret; /* Return value */
#include <asm-generic/ide_iops.h>
#endif
-#ifndef MAX_HWIFS
-#if defined(CONFIG_BLACKFIN) || defined(CONFIG_H8300) || defined(CONFIG_XTENSA)
-# define MAX_HWIFS 1
-#else
-# define MAX_HWIFS 10
-#endif
-#endif
-
-#if !defined(MAX_HWIFS) || defined(CONFIG_EMBEDDED)
-#undef MAX_HWIFS
-#define MAX_HWIFS CONFIG_IDE_MAX_HWIFS
-#endif
+#define MAX_HWIFS 10
/* Currently only m68k, apus and m8xx need it */
#ifndef IDE_ARCH_ACK_INTR
extern const struct ide_tp_ops default_tp_ops;
+/**
+ * struct ide_port_ops - IDE port operations
+ *
+ * @init_dev: host specific initialization of a device
+ * @set_pio_mode: routine to program host for PIO mode
+ * @set_dma_mode: routine to program host for DMA mode
+ * @selectproc: tweaks hardware to select drive
+ * @reset_poll: chipset polling based on hba specifics
+ * @pre_reset: chipset specific changes to default for device-hba resets
+ * @resetproc: routine to reset controller after a disk reset
+ * @maskproc: special host masking for drive selection
+ * @quirkproc: check host's drive quirk list
+ *
+ * @mdma_filter: filter MDMA modes
+ * @udma_filter: filter UDMA modes
+ *
+ * @cable_detect: detect cable type
+ */
struct ide_port_ops {
- /* host specific initialization of a device */
void (*init_dev)(ide_drive_t *);
- /* routine to program host for PIO mode */
void (*set_pio_mode)(ide_drive_t *, const u8);
- /* routine to program host for DMA mode */
void (*set_dma_mode)(ide_drive_t *, const u8);
- /* tweaks hardware to select drive */
void (*selectproc)(ide_drive_t *);
- /* chipset polling based on hba specifics */
int (*reset_poll)(ide_drive_t *);
- /* chipset specific changes to default for device-hba resets */
void (*pre_reset)(ide_drive_t *);
- /* routine to reset controller after a disk reset */
void (*resetproc)(ide_drive_t *);
- /* special host masking for drive selection */
void (*maskproc)(ide_drive_t *, int);
- /* check host's drive quirk list */
void (*quirkproc)(ide_drive_t *);
u8 (*mdma_filter)(ide_drive_t *);
u8 count;
} __attribute__ ((packed));
+/**
+ * struct ieee80211_tim
+ *
+ * This structure refers to "Traffic Indication Map information element"
+ */
+struct ieee80211_tim_ie {
+ u8 dtim_count;
+ u8 dtim_period;
+ u8 bitmap_ctrl;
+ /* variable size: 1 - 251 bytes */
+ u8 virtual_map[0];
+} __attribute__ ((packed));
+
struct ieee80211_mgmt {
__le16 frame_control;
__le16 duration;
__be32 addr;
__be16 len;
uint8_t data[0];
-} __attribute__((aligned(4)));
+} __attribute__((packed));
/* Find the next record, taking into account the 4-byte alignment */
static inline const struct ihex_binrec *
#define or_softirq_pending(x) (local_softirq_pending() |= (x))
#endif
-/*
- * Temporary defines for UP kernels, until all code gets fixed.
- */
-#ifndef CONFIG_SMP
-static inline void __deprecated cli(void)
-{
- local_irq_disable();
-}
-static inline void __deprecated sti(void)
-{
- local_irq_enable();
-}
-static inline void __deprecated save_flags(unsigned long *x)
-{
- local_save_flags(*x);
-}
-#define save_flags(x) save_flags(&x)
-static inline void __deprecated restore_flags(unsigned long x)
-{
- local_irq_restore(x);
-}
-
-static inline void __deprecated save_and_cli(unsigned long *x)
-{
- local_irq_save(*x);
-}
-#define save_and_cli(x) save_and_cli(&x)
-#endif /* CONFIG_SMP */
-
/* Some architectures might implement lazy enabling/disabling of
* interrupts. In some cases, such as stop_machine, we might want
* to ensure that after a local_irq_disable(), interrupts have
unsigned long align_mask);
extern void iommu_area_free(unsigned long *map, unsigned long start,
unsigned int nr);
-extern unsigned long iommu_num_pages(unsigned long addr, unsigned long len);
int adjust_resource(struct resource *res, resource_size_t start,
resource_size_t size);
resource_size_t resource_alignment(struct resource *res);
+static inline resource_size_t resource_size(struct resource *res)
+{
+ return res->end - res->start + 1;
+}
/* Convenience shorthand with allocation */
#define request_region(start,n,name) __request_region(&ioport_resource, (start), (n), (name))
--- /dev/null
+/*
+ * IP Virtual Server
+ * data structure and functionality definitions
+ */
+
+#ifndef _IP_VS_H
+#define _IP_VS_H
+
+#include <linux/types.h> /* For __beXX types in userland */
+
+#define IP_VS_VERSION_CODE 0x010201
+#define NVERSION(version) \
+ (version >> 16) & 0xFF, \
+ (version >> 8) & 0xFF, \
+ version & 0xFF
+
+/*
+ * Virtual Service Flags
+ */
+#define IP_VS_SVC_F_PERSISTENT 0x0001 /* persistent port */
+#define IP_VS_SVC_F_HASHED 0x0002 /* hashed entry */
+
+/*
+ * Destination Server Flags
+ */
+#define IP_VS_DEST_F_AVAILABLE 0x0001 /* server is available */
+#define IP_VS_DEST_F_OVERLOAD 0x0002 /* server is overloaded */
+
+/*
+ * IPVS sync daemon states
+ */
+#define IP_VS_STATE_NONE 0x0000 /* daemon is stopped */
+#define IP_VS_STATE_MASTER 0x0001 /* started as master */
+#define IP_VS_STATE_BACKUP 0x0002 /* started as backup */
+
+/*
+ * IPVS socket options
+ */
+#define IP_VS_BASE_CTL (64+1024+64) /* base */
+
+#define IP_VS_SO_SET_NONE IP_VS_BASE_CTL /* just peek */
+#define IP_VS_SO_SET_INSERT (IP_VS_BASE_CTL+1)
+#define IP_VS_SO_SET_ADD (IP_VS_BASE_CTL+2)
+#define IP_VS_SO_SET_EDIT (IP_VS_BASE_CTL+3)
+#define IP_VS_SO_SET_DEL (IP_VS_BASE_CTL+4)
+#define IP_VS_SO_SET_FLUSH (IP_VS_BASE_CTL+5)
+#define IP_VS_SO_SET_LIST (IP_VS_BASE_CTL+6)
+#define IP_VS_SO_SET_ADDDEST (IP_VS_BASE_CTL+7)
+#define IP_VS_SO_SET_DELDEST (IP_VS_BASE_CTL+8)
+#define IP_VS_SO_SET_EDITDEST (IP_VS_BASE_CTL+9)
+#define IP_VS_SO_SET_TIMEOUT (IP_VS_BASE_CTL+10)
+#define IP_VS_SO_SET_STARTDAEMON (IP_VS_BASE_CTL+11)
+#define IP_VS_SO_SET_STOPDAEMON (IP_VS_BASE_CTL+12)
+#define IP_VS_SO_SET_RESTORE (IP_VS_BASE_CTL+13)
+#define IP_VS_SO_SET_SAVE (IP_VS_BASE_CTL+14)
+#define IP_VS_SO_SET_ZERO (IP_VS_BASE_CTL+15)
+#define IP_VS_SO_SET_MAX IP_VS_SO_SET_ZERO
+
+#define IP_VS_SO_GET_VERSION IP_VS_BASE_CTL
+#define IP_VS_SO_GET_INFO (IP_VS_BASE_CTL+1)
+#define IP_VS_SO_GET_SERVICES (IP_VS_BASE_CTL+2)
+#define IP_VS_SO_GET_SERVICE (IP_VS_BASE_CTL+3)
+#define IP_VS_SO_GET_DESTS (IP_VS_BASE_CTL+4)
+#define IP_VS_SO_GET_DEST (IP_VS_BASE_CTL+5) /* not used now */
+#define IP_VS_SO_GET_TIMEOUT (IP_VS_BASE_CTL+6)
+#define IP_VS_SO_GET_DAEMON (IP_VS_BASE_CTL+7)
+#define IP_VS_SO_GET_MAX IP_VS_SO_GET_DAEMON
+
+
+/*
+ * IPVS Connection Flags
+ */
+#define IP_VS_CONN_F_FWD_MASK 0x0007 /* mask for the fwd methods */
+#define IP_VS_CONN_F_MASQ 0x0000 /* masquerading/NAT */
+#define IP_VS_CONN_F_LOCALNODE 0x0001 /* local node */
+#define IP_VS_CONN_F_TUNNEL 0x0002 /* tunneling */
+#define IP_VS_CONN_F_DROUTE 0x0003 /* direct routing */
+#define IP_VS_CONN_F_BYPASS 0x0004 /* cache bypass */
+#define IP_VS_CONN_F_SYNC 0x0020 /* entry created by sync */
+#define IP_VS_CONN_F_HASHED 0x0040 /* hashed entry */
+#define IP_VS_CONN_F_NOOUTPUT 0x0080 /* no output packets */
+#define IP_VS_CONN_F_INACTIVE 0x0100 /* not established */
+#define IP_VS_CONN_F_OUT_SEQ 0x0200 /* must do output seq adjust */
+#define IP_VS_CONN_F_IN_SEQ 0x0400 /* must do input seq adjust */
+#define IP_VS_CONN_F_SEQ_MASK 0x0600 /* in/out sequence mask */
+#define IP_VS_CONN_F_NO_CPORT 0x0800 /* no client port set yet */
+#define IP_VS_CONN_F_TEMPLATE 0x1000 /* template, not connection */
+
+#define IP_VS_SCHEDNAME_MAXLEN 16
+#define IP_VS_IFNAME_MAXLEN 16
+
+
+/*
+ * The struct ip_vs_service_user and struct ip_vs_dest_user are
+ * used to set IPVS rules through setsockopt.
+ */
+struct ip_vs_service_user {
+ /* virtual service addresses */
+ u_int16_t protocol;
+ __be32 addr; /* virtual ip address */
+ __be16 port;
+ u_int32_t fwmark; /* firwall mark of service */
+
+ /* virtual service options */
+ char sched_name[IP_VS_SCHEDNAME_MAXLEN];
+ unsigned flags; /* virtual service flags */
+ unsigned timeout; /* persistent timeout in sec */
+ __be32 netmask; /* persistent netmask */
+};
+
+
+struct ip_vs_dest_user {
+ /* destination server address */
+ __be32 addr;
+ __be16 port;
+
+ /* real server options */
+ unsigned conn_flags; /* connection flags */
+ int weight; /* destination weight */
+
+ /* thresholds for active connections */
+ u_int32_t u_threshold; /* upper threshold */
+ u_int32_t l_threshold; /* lower threshold */
+};
+
+
+/*
+ * IPVS statistics object (for user space)
+ */
+struct ip_vs_stats_user
+{
+ __u32 conns; /* connections scheduled */
+ __u32 inpkts; /* incoming packets */
+ __u32 outpkts; /* outgoing packets */
+ __u64 inbytes; /* incoming bytes */
+ __u64 outbytes; /* outgoing bytes */
+
+ __u32 cps; /* current connection rate */
+ __u32 inpps; /* current in packet rate */
+ __u32 outpps; /* current out packet rate */
+ __u32 inbps; /* current in byte rate */
+ __u32 outbps; /* current out byte rate */
+};
+
+
+/* The argument to IP_VS_SO_GET_INFO */
+struct ip_vs_getinfo {
+ /* version number */
+ unsigned int version;
+
+ /* size of connection hash table */
+ unsigned int size;
+
+ /* number of virtual services */
+ unsigned int num_services;
+};
+
+
+/* The argument to IP_VS_SO_GET_SERVICE */
+struct ip_vs_service_entry {
+ /* which service: user fills in these */
+ u_int16_t protocol;
+ __be32 addr; /* virtual address */
+ __be16 port;
+ u_int32_t fwmark; /* firwall mark of service */
+
+ /* service options */
+ char sched_name[IP_VS_SCHEDNAME_MAXLEN];
+ unsigned flags; /* virtual service flags */
+ unsigned timeout; /* persistent timeout */
+ __be32 netmask; /* persistent netmask */
+
+ /* number of real servers */
+ unsigned int num_dests;
+
+ /* statistics */
+ struct ip_vs_stats_user stats;
+};
+
+
+struct ip_vs_dest_entry {
+ __be32 addr; /* destination address */
+ __be16 port;
+ unsigned conn_flags; /* connection flags */
+ int weight; /* destination weight */
+
+ u_int32_t u_threshold; /* upper threshold */
+ u_int32_t l_threshold; /* lower threshold */
+
+ u_int32_t activeconns; /* active connections */
+ u_int32_t inactconns; /* inactive connections */
+ u_int32_t persistconns; /* persistent connections */
+
+ /* statistics */
+ struct ip_vs_stats_user stats;
+};
+
+
+/* The argument to IP_VS_SO_GET_DESTS */
+struct ip_vs_get_dests {
+ /* which service: user fills in these */
+ u_int16_t protocol;
+ __be32 addr; /* virtual address */
+ __be16 port;
+ u_int32_t fwmark; /* firwall mark of service */
+
+ /* number of real servers */
+ unsigned int num_dests;
+
+ /* the real servers */
+ struct ip_vs_dest_entry entrytable[0];
+};
+
+
+/* The argument to IP_VS_SO_GET_SERVICES */
+struct ip_vs_get_services {
+ /* number of virtual services */
+ unsigned int num_services;
+
+ /* service table */
+ struct ip_vs_service_entry entrytable[0];
+};
+
+
+/* The argument to IP_VS_SO_GET_TIMEOUT */
+struct ip_vs_timeout_user {
+ int tcp_timeout;
+ int tcp_fin_timeout;
+ int udp_timeout;
+};
+
+
+/* The argument to IP_VS_SO_GET_DAEMON */
+struct ip_vs_daemon_user {
+ /* sync daemon state (master/backup) */
+ int state;
+
+ /* multicast interface name */
+ char mcast_ifn[IP_VS_IFNAME_MAXLEN];
+
+ /* SyncID we belong to */
+ int syncid;
+};
+
+#endif /* _IP_VS_H */
static inline void print_ip_sym(unsigned long ip)
{
- printk("[<%p>]", (void *) ip);
- print_symbol(" %s\n", ip);
+ printk("[<%p>] %pS\n", (void *) ip, (void *) ip);
}
#endif /*_LINUX_KALLSYMS_H*/
*/
#define upper_32_bits(n) ((u32)(((n) >> 16) >> 16))
+/**
+ * lower_32_bits - return bits 0-31 of a number
+ * @n: the number we're accessing
+ */
+#define lower_32_bits(n) ((u32)(n))
+
#define KERN_EMERG "<0>" /* system is unusable */
#define KERN_ALERT "<1>" /* action must be taken immediately */
#define KERN_CRIT "<2>" /* critical conditions */
__attribute__ ((format (printf, 1, 2)));
unsigned long paddr_vmcoreinfo_note(void);
-#define VMCOREINFO_OSRELEASE(name) \
- vmcoreinfo_append_str("OSRELEASE=%s\n", #name)
+#define VMCOREINFO_OSRELEASE(value) \
+ vmcoreinfo_append_str("OSRELEASE=%s\n", value)
#define VMCOREINFO_PAGESIZE(value) \
vmcoreinfo_append_str("PAGESIZE=%ld\n", value)
#define VMCOREINFO_SYMBOL(name) \
#define KVM_CAP_PV_MMU 13
#define KVM_CAP_MP_STATE 14
#define KVM_CAP_COALESCED_MMIO 15
+#define KVM_CAP_SYNC_MMU 16 /* Changes to host mmap are reflected in guest */
/*
* ioctls for VM fds
struct kvm_coalesced_mmio_dev *coalesced_mmio_dev;
struct kvm_coalesced_mmio_ring *coalesced_mmio_ring;
#endif
+
+#ifdef KVM_ARCH_WANT_MMU_NOTIFIER
+ struct mmu_notifier mmu_notifier;
+ unsigned long mmu_notifier_seq;
+ long mmu_notifier_count;
+#endif
};
/* The guest did something we don't support. */
#define kvm_trace_cleanup() ((void)0)
#endif
+#ifdef KVM_ARCH_WANT_MMU_NOTIFIER
+static inline int mmu_notifier_retry(struct kvm_vcpu *vcpu, unsigned long mmu_seq)
+{
+ if (unlikely(vcpu->kvm->mmu_notifier_count))
+ return 1;
+ /*
+ * Both reads happen under the mmu_lock and both values are
+ * modified under mmu_lock, so there's no need of smb_rmb()
+ * here in between, otherwise mmu_notifier_count should be
+ * read before mmu_notifier_seq, see
+ * mmu_notifier_invalidate_range_end write side.
+ */
+ if (vcpu->kvm->mmu_notifier_seq != mmu_seq)
+ return 1;
+ return 0;
+}
+#endif
+
#endif
/* note: prints function name for you */
#ifdef ATA_DEBUG
-#define DPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define DPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#ifdef ATA_VERBOSE_DEBUG
-#define VPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define VPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#else
#define VPRINTK(fmt, args...)
#endif /* ATA_VERBOSE_DEBUG */
#define VPRINTK(fmt, args...)
#endif /* ATA_DEBUG */
-#define BPRINTK(fmt, args...) if (ap->flags & ATA_FLAG_DEBUGMSG) printk(KERN_ERR "%s: " fmt, __FUNCTION__, ## args)
+#define BPRINTK(fmt, args...) if (ap->flags & ATA_FLAG_DEBUGMSG) printk(KERN_ERR "%s: " fmt, __func__, ## args)
/* NEW: debug levels */
#define HAVE_LIBATA_MSG 1
void (*set_piomode)(struct ata_port *ap, struct ata_device *dev);
void (*set_dmamode)(struct ata_port *ap, struct ata_device *dev);
int (*set_mode)(struct ata_link *link, struct ata_device **r_failed_dev);
+ unsigned int (*read_id)(struct ata_device *dev, struct ata_taskfile *tf, u16 *id);
void (*dev_config)(struct ata_device *dev);
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
+extern unsigned int ata_do_dev_read_id(struct ata_device *dev,
+ struct ata_taskfile *tf, u16 *id);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active);
extern void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd,
return !list_empty(head) && (head->next == head->prev);
}
+static inline void __list_cut_position(struct list_head *list,
+ struct list_head *head, struct list_head *entry)
+{
+ struct list_head *new_first = entry->next;
+ list->next = head->next;
+ list->next->prev = list;
+ list->prev = entry;
+ entry->next = list;
+ head->next = new_first;
+ new_first->prev = head;
+}
+
+/**
+ * list_cut_position - cut a list into two
+ * @list: a new list to add all removed entries
+ * @head: a list with entries
+ * @entry: an entry within head, could be the head itself
+ * and if so we won't cut the list
+ *
+ * This helper moves the initial part of @head, up to and
+ * including @entry, from @head to @list. You should
+ * pass on @entry an element you know is on @head. @list
+ * should be an empty list or a list you do not care about
+ * losing its data.
+ *
+ */
+static inline void list_cut_position(struct list_head *list,
+ struct list_head *head, struct list_head *entry)
+{
+ if (list_empty(head))
+ return;
+ if (list_is_singular(head) &&
+ (head->next != entry && head != entry))
+ return;
+ if (entry == head)
+ INIT_LIST_HEAD(list);
+ else
+ __list_cut_position(list, head, entry);
+}
+
static inline void __list_splice(const struct list_head *list,
- struct list_head *head)
+ struct list_head *prev,
+ struct list_head *next)
{
struct list_head *first = list->next;
struct list_head *last = list->prev;
- struct list_head *at = head->next;
- first->prev = head;
- head->next = first;
+ first->prev = prev;
+ prev->next = first;
- last->next = at;
- at->prev = last;
+ last->next = next;
+ next->prev = last;
}
/**
- * list_splice - join two lists
+ * list_splice - join two lists, this is designed for stacks
* @list: the new list to add.
* @head: the place to add it in the first list.
*/
struct list_head *head)
{
if (!list_empty(list))
- __list_splice(list, head);
+ __list_splice(list, head, head->next);
+}
+
+/**
+ * list_splice_tail - join two lists, each list being a queue
+ * @list: the new list to add.
+ * @head: the place to add it in the first list.
+ */
+static inline void list_splice_tail(struct list_head *list,
+ struct list_head *head)
+{
+ if (!list_empty(list))
+ __list_splice(list, head->prev, head);
}
/**
struct list_head *head)
{
if (!list_empty(list)) {
- __list_splice(list, head);
+ __list_splice(list, head, head->next);
+ INIT_LIST_HEAD(list);
+ }
+}
+
+/**
+ * list_splice_tail_init - join two lists and reinitialise the emptied list
+ * @list: the new list to add.
+ * @head: the place to add it in the first list.
+ *
+ * Each of the lists is a queue.
+ * The list at @list is reinitialised
+ */
+static inline void list_splice_tail_init(struct list_head *list,
+ struct list_head *head)
+{
+ if (!list_empty(list)) {
+ __list_splice(list, head->prev, head);
INIT_LIST_HEAD(list);
}
}
*/
#define MISDN_MAJOR_VERSION 1
#define MISDN_MINOR_VERSION 0
-#define MISDN_RELEASE 18
+#define MISDN_RELEASE 19
/* primitives for information exchange
* generell format
#define TEI_SAPI 63
#define CTRL_SAPI 0
-#define MISDN_CHMAP_SIZE 4
+#define MISDN_MAX_CHANNEL 127
+#define MISDN_CHMAP_SIZE ((MISDN_MAX_CHANNEL + 1) >> 3)
#define SOL_MISDN 0
u_int Dprotocols;
u_int Bprotocols;
u_int protocol;
- u_long channelmap[MISDN_CHMAP_SIZE];
+ u_char channelmap[MISDN_CHMAP_SIZE];
u_int nrbchan;
char name[MISDN_MAX_IDLEN];
};
+static inline int
+test_channelmap(u_int nr, u_char *map)
+{
+ if (nr <= MISDN_MAX_CHANNEL)
+ return map[nr >> 3] & (1 << (nr & 7));
+ else
+ return 0;
+}
+
+static inline void
+set_channelmap(u_int nr, u_char *map)
+{
+ map[nr >> 3] |= (1 << (nr & 7));
+}
+
+static inline void
+clear_channelmap(u_int nr, u_char *map)
+{
+ map[nr >> 3] &= ~(1 << (nr & 7));
+}
+
/* CONTROL_CHANNEL parameters */
#define MISDN_CTRL_GETOP 0x0000
#define MISDN_CTRL_LOOP 0x0001
u_int Dprotocols;
u_int Bprotocols;
u_int nrbchan;
- u_long channelmap[MISDN_CHMAP_SIZE];
+ u_char channelmap[MISDN_CHMAP_SIZE];
struct list_head bchannels;
struct mISDNchannel *teimgr;
struct device dev;
#endif
};
-/* global alloc/queue dunctions */
+/* global alloc/queue functions */
static inline struct sk_buff *
mI_alloc_skb(unsigned int len, gfp_t gfp_mask)
#define __LINUX_MAPLE_H
#include <linux/device.h>
+#include <mach/maple.h>
extern struct bus_type maple_bus_type;
void *sendbuf, *recvbuf, *recvbufdcsp;
unsigned char length;
enum maple_code command;
+ struct mutex mutex;
};
struct maple_devinfo {
struct maple_device {
struct maple_driver *driver;
struct mapleq *mq;
- void *private_data;
void (*callback) (struct mapleq * mq);
unsigned long when, interval, function;
struct maple_devinfo devinfo;
void (*callback) (struct mapleq * mq),
unsigned long interval,
unsigned long function);
-int maple_driver_register(struct device_driver *drv);
-void maple_add_packet(struct mapleq *mq);
+int maple_driver_register(struct maple_driver *);
+void maple_driver_unregister(struct maple_driver *);
+
+int maple_add_packet_sleeps(struct maple_device *mdev, u32 function,
+ u32 command, u32 length, void *data);
+void maple_clear_dev(struct maple_device *mdev);
#define to_maple_dev(n) container_of(n, struct maple_device, dev)
#define to_maple_driver(n) container_of(n, struct maple_driver, drv)
+#define maple_get_drvdata(d) dev_get_drvdata(&(d)->dev)
+#define maple_set_drvdata(d,p) dev_set_drvdata(&(d)->dev, (p))
+
#endif /* __LINUX_MAPLE_H */
#include <linux/mlx4/doorbell.h>
struct mlx4_cqe {
- __be32 my_qpn;
+ __be32 vlan_my_qpn;
__be32 immed_rss_invalid;
__be32 g_mlpath_rqpn;
- u8 sl;
- u8 reserved1;
+ __be16 sl_vid;
__be16 rlid;
- __be32 ipoib_status;
+ __be16 status;
+ u8 ipv6_ext_mask;
+ u8 badfcs_enc;
__be32 byte_cnt;
__be16 wqe_index;
__be16 checksum;
- u8 reserved2[3];
+ u8 reserved[3];
u8 owner_sr_opcode;
};
u8 owner_sr_opcode;
};
+enum {
+ MLX4_CQE_VLAN_PRESENT_MASK = 1 << 29,
+ MLX4_CQE_QPN_MASK = 0xffffff,
+};
+
enum {
MLX4_CQE_OWNER_MASK = 0x80,
MLX4_CQE_IS_SEND_MASK = 0x40,
};
enum {
- MLX4_CQE_IPOIB_STATUS_IPV4 = 1 << 22,
- MLX4_CQE_IPOIB_STATUS_IPV4F = 1 << 23,
- MLX4_CQE_IPOIB_STATUS_IPV6 = 1 << 24,
- MLX4_CQE_IPOIB_STATUS_IPV4OPT = 1 << 25,
- MLX4_CQE_IPOIB_STATUS_TCP = 1 << 26,
- MLX4_CQE_IPOIB_STATUS_UDP = 1 << 27,
- MLX4_CQE_IPOIB_STATUS_IPOK = 1 << 28,
+ MLX4_CQE_STATUS_IPV4 = 1 << 6,
+ MLX4_CQE_STATUS_IPV4F = 1 << 7,
+ MLX4_CQE_STATUS_IPV6 = 1 << 8,
+ MLX4_CQE_STATUS_IPV4OPT = 1 << 9,
+ MLX4_CQE_STATUS_TCP = 1 << 10,
+ MLX4_CQE_STATUS_UDP = 1 << 11,
+ MLX4_CQE_STATUS_IPOK = 1 << 12,
+};
+
+enum {
+ MLX4_CQE_LLC = 1,
+ MLX4_CQE_SNAP = 1 << 1,
+ MLX4_CQE_BAD_FCS = 1 << 4,
};
static inline void mlx4_cq_arm(struct mlx4_cq *cq, u32 cmd,
struct page *vm_normal_page(struct vm_area_struct *vma, unsigned long addr,
pte_t pte);
+int zap_vma_ptes(struct vm_area_struct *vma, unsigned long address,
+ unsigned long size);
unsigned long zap_page_range(struct vm_area_struct *vma, unsigned long address,
unsigned long size, struct zap_details *);
unsigned long unmap_vmas(struct mmu_gather **tlb,
extern void get_pfn_range_for_nid(unsigned int nid,
unsigned long *start_pfn, unsigned long *end_pfn);
extern unsigned long find_min_pfn_with_active_regions(void);
-extern unsigned long find_max_pfn_with_active_regions(void);
extern void free_bootmem_with_active_regions(int nid,
unsigned long max_low_pfn);
typedef int (*work_fn_t)(unsigned long, unsigned long, void *);
struct nameidata;
-extern int do_add_mount(struct vfsmount *newmnt, struct nameidata *nd,
+struct path;
+extern int do_add_mount(struct vfsmount *newmnt, struct path *path,
int mnt_flags, struct list_head *fslist);
extern void mark_mounts_for_expiry(struct list_head *mounts);
printk(KERN_INFO args); \
} while(0)
#else /* CONFIG_MTD_DEBUG */
-#define DEBUG(n, args...) do { } while(0)
+#define DEBUG(n, args...) \
+ do { \
+ if (0) \
+ printk(KERN_INFO args); \
+ } while(0)
#endif /* CONFIG_MTD_DEBUG */
#define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING))
#define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
#define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK))
-#define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT))
+/* Large page NAND with SOFT_ECC should support subpage reads */
+#define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \
+ && (chip->page_shift > 9))
/* Mask to zero out the chip options, which come from the id table */
#define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR)
#define NET_XMIT_DROP 1 /* skb dropped */
#define NET_XMIT_CN 2 /* congestion notification */
#define NET_XMIT_POLICED 3 /* skb is shot by police */
-#define NET_XMIT_BYPASS 4 /* packet does not leave via dequeue;
- (TC use only - dev_queue_xmit
- returns this as NET_XMIT_SUCCESS) */
+#define NET_XMIT_MASK 0xFFFF /* qdisc flags in net/sch_generic.h */
/* Backlog congestion levels */
#define NET_RX_SUCCESS 0 /* keep 'em coming, baby */
enum netdev_queue_state_t
{
__QUEUE_STATE_XOFF,
+ __QUEUE_STATE_FROZEN,
};
struct netdev_queue {
unsigned int real_num_tx_queues;
unsigned long tx_queue_len; /* Max frames per queue allowed */
-
+ spinlock_t tx_global_lock;
/*
* One part is mostly used on xmit path (device)
*/
return netif_tx_queue_stopped(netdev_get_tx_queue(dev, 0));
}
+static inline int netif_tx_queue_frozen(const struct netdev_queue *dev_queue)
+{
+ return test_bit(__QUEUE_STATE_FROZEN, &dev_queue->state);
+}
+
/**
* netif_running - test if up
* @dev: network device
txq->xmit_lock_owner = smp_processor_id();
}
+static inline int __netif_tx_trylock(struct netdev_queue *txq)
+{
+ int ok = spin_trylock(&txq->_xmit_lock);
+ if (likely(ok))
+ txq->xmit_lock_owner = smp_processor_id();
+ return ok;
+}
+
+static inline void __netif_tx_unlock(struct netdev_queue *txq)
+{
+ txq->xmit_lock_owner = -1;
+ spin_unlock(&txq->_xmit_lock);
+}
+
+static inline void __netif_tx_unlock_bh(struct netdev_queue *txq)
+{
+ txq->xmit_lock_owner = -1;
+ spin_unlock_bh(&txq->_xmit_lock);
+}
+
/**
* netif_tx_lock - grab network device transmit lock
* @dev: network device
*/
static inline void netif_tx_lock(struct net_device *dev)
{
- int cpu = smp_processor_id();
unsigned int i;
+ int cpu;
+ spin_lock(&dev->tx_global_lock);
+ cpu = smp_processor_id();
for (i = 0; i < dev->num_tx_queues; i++) {
struct netdev_queue *txq = netdev_get_tx_queue(dev, i);
+
+ /* We are the only thread of execution doing a
+ * freeze, but we have to grab the _xmit_lock in
+ * order to synchronize with threads which are in
+ * the ->hard_start_xmit() handler and already
+ * checked the frozen bit.
+ */
__netif_tx_lock(txq, cpu);
+ set_bit(__QUEUE_STATE_FROZEN, &txq->state);
+ __netif_tx_unlock(txq);
}
}
netif_tx_lock(dev);
}
-static inline int __netif_tx_trylock(struct netdev_queue *txq)
-{
- int ok = spin_trylock(&txq->_xmit_lock);
- if (likely(ok))
- txq->xmit_lock_owner = smp_processor_id();
- return ok;
-}
-
-static inline int netif_tx_trylock(struct net_device *dev)
-{
- return __netif_tx_trylock(netdev_get_tx_queue(dev, 0));
-}
-
-static inline void __netif_tx_unlock(struct netdev_queue *txq)
-{
- txq->xmit_lock_owner = -1;
- spin_unlock(&txq->_xmit_lock);
-}
-
-static inline void __netif_tx_unlock_bh(struct netdev_queue *txq)
-{
- txq->xmit_lock_owner = -1;
- spin_unlock_bh(&txq->_xmit_lock);
-}
-
static inline void netif_tx_unlock(struct net_device *dev)
{
unsigned int i;
for (i = 0; i < dev->num_tx_queues; i++) {
struct netdev_queue *txq = netdev_get_tx_queue(dev, i);
- __netif_tx_unlock(txq);
- }
+ /* No need to grab the _xmit_lock here. If the
+ * queue is not stopped for another reason, we
+ * force a schedule.
+ */
+ clear_bit(__QUEUE_STATE_FROZEN, &txq->state);
+ if (!test_bit(__QUEUE_STATE_XOFF, &txq->state))
+ __netif_schedule(txq->qdisc);
+ }
+ spin_unlock(&dev->tx_global_lock);
}
static inline void netif_tx_unlock_bh(struct net_device *dev)
static inline void netif_tx_disable(struct net_device *dev)
{
unsigned int i;
+ int cpu;
- netif_tx_lock_bh(dev);
+ local_bh_disable();
+ cpu = smp_processor_id();
for (i = 0; i < dev->num_tx_queues; i++) {
struct netdev_queue *txq = netdev_get_tx_queue(dev, i);
+
+ __netif_tx_lock(txq, cpu);
netif_tx_stop_queue(txq);
+ __netif_tx_unlock(txq);
}
- netif_tx_unlock_bh(dev);
+ local_bh_enable();
}
static inline void netif_addr_lock(struct net_device *dev)
/* Be liberal in window checking */
#define IP_CT_TCP_FLAG_BE_LIBERAL 0x08
+/* Has unacknowledged data */
+#define IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED 0x10
+
struct nf_ct_tcp_flags {
u_int8_t flags;
u_int8_t mask;
struct page; /* forward declaration */
-PAGEFLAG(Locked, locked) TESTSCFLAG(Locked, locked)
+TESTPAGEFLAG(Locked, locked)
PAGEFLAG(Error, error)
PAGEFLAG(Referenced, referenced) TESTCLEARFLAG(Referenced, referenced)
PAGEFLAG(Dirty, dirty) TESTSCFLAG(Dirty, dirty) __CLEARPAGEFLAG(Dirty, dirty)
{
smp_wmb();
__set_bit(PG_uptodate, &(page)->flags);
-#ifdef CONFIG_S390
- page_clear_dirty(page);
-#endif
}
static inline void SetPageUptodate(struct page *page)
return 1;
}
+/*
+ * Same as above, but add instead of inc (could just be merged)
+ */
+static inline int page_cache_add_speculative(struct page *page, int count)
+{
+ VM_BUG_ON(in_interrupt());
+
+#if !defined(CONFIG_SMP) && defined(CONFIG_CLASSIC_RCU)
+# ifdef CONFIG_PREEMPT
+ VM_BUG_ON(!in_atomic());
+# endif
+ VM_BUG_ON(page_count(page) == 0);
+ atomic_add(count, &page->_count);
+
+#else
+ if (unlikely(!atomic_add_unless(&page->_count, count, 0)))
+ return 0;
+#endif
+ VM_BUG_ON(PageCompound(page) && page != compound_head(page));
+
+ return 1;
+}
+
static inline int page_freeze_refs(struct page *page, int count)
{
return likely(atomic_cmpxchg(&page->_count, count, 0) == count);
return read_cache_page(mapping, index, filler, data);
}
-int add_to_page_cache_locked(struct page *page, struct address_space *mapping,
- pgoff_t index, gfp_t gfp_mask);
-int add_to_page_cache_lru(struct page *page, struct address_space *mapping,
- pgoff_t index, gfp_t gfp_mask);
-extern void remove_from_page_cache(struct page *page);
-extern void __remove_from_page_cache(struct page *page);
-
-/*
- * Like add_to_page_cache_locked, but used to add newly allocated pages:
- * the page is new, so we can just run SetPageLocked() against it.
- */
-static inline int add_to_page_cache(struct page *page,
- struct address_space *mapping, pgoff_t offset, gfp_t gfp_mask)
-{
- int error;
-
- SetPageLocked(page);
- error = add_to_page_cache_locked(page, mapping, offset, gfp_mask);
- if (unlikely(error))
- ClearPageLocked(page);
- return error;
-}
-
/*
* Return byte-offset into filesystem object for page.
*/
extern void __lock_page_nosync(struct page *page);
extern void unlock_page(struct page *page);
+static inline void set_page_locked(struct page *page)
+{
+ set_bit(PG_locked, &page->flags);
+}
+
+static inline void clear_page_locked(struct page *page)
+{
+ clear_bit(PG_locked, &page->flags);
+}
+
+static inline int trylock_page(struct page *page)
+{
+ return !test_and_set_bit(PG_locked, &page->flags);
+}
+
/*
* lock_page may only be called if we have the page's inode pinned.
*/
static inline void lock_page(struct page *page)
{
might_sleep();
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
__lock_page(page);
}
static inline int lock_page_killable(struct page *page)
{
might_sleep();
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
return __lock_page_killable(page);
return 0;
}
static inline void lock_page_nosync(struct page *page)
{
might_sleep();
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
__lock_page_nosync(page);
}
return ret;
}
+int add_to_page_cache_locked(struct page *page, struct address_space *mapping,
+ pgoff_t index, gfp_t gfp_mask);
+int add_to_page_cache_lru(struct page *page, struct address_space *mapping,
+ pgoff_t index, gfp_t gfp_mask);
+extern void remove_from_page_cache(struct page *page);
+extern void __remove_from_page_cache(struct page *page);
+
+/*
+ * Like add_to_page_cache_locked, but used to add newly allocated pages:
+ * the page is new, so we can just run set_page_locked() against it.
+ */
+static inline int add_to_page_cache(struct page *page,
+ struct address_space *mapping, pgoff_t offset, gfp_t gfp_mask)
+{
+ int error;
+
+ set_page_locked(page);
+ error = add_to_page_cache_locked(page, mapping, offset, gfp_mask);
+ if (unlikely(error))
+ clear_page_locked(page);
+ return error;
+}
+
#endif /* _LINUX_PAGEMAP_H */
const char *pattern;
};
-typedef const struct match_token match_table_t[];
+typedef struct match_token match_table_t[];
/* Maximum number of arguments that match_token will find in a pattern */
enum {MAX_OPT_ARGS = 3};
/* interface for the pm_qos_power infrastructure of the linux kernel.
*
- * Mark Gross
+ * Mark Gross <mgross@linux.intel.com>
*/
#include <linux/list.h>
#include <linux/notifier.h>
POWER_SUPPLY_PROP_CHARGE_EMPTY,
POWER_SUPPLY_PROP_CHARGE_NOW,
POWER_SUPPLY_PROP_CHARGE_AVG,
+ POWER_SUPPLY_PROP_CHARGE_COUNTER,
POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN,
POWER_SUPPLY_PROP_ENERGY_EMPTY_DESIGN,
POWER_SUPPLY_PROP_ENERGY_FULL,
child->ptrace = 0;
if (unlikely(ptrace)) {
child->ptrace = current->ptrace;
- __ptrace_link(child, current->parent);
+ ptrace_link(child, current->parent);
}
}
int vfs_quota_on(struct super_block *sb, int type, int format_id,
char *path, int remount);
+int vfs_quota_on_path(struct super_block *sb, int type, int format_id,
+ struct path *path);
int vfs_quota_on_mount(struct super_block *sb, char *qf_name,
int format_id, int type);
int vfs_quota_off(struct super_block *sb, int type, int remount);
#define MD_CHANGE_DEVS 0 /* Some device status has changed */
#define MD_CHANGE_CLEAN 1 /* transition to or from 'clean' */
#define MD_CHANGE_PENDING 2 /* superblock update in progress */
+#define MD_NOTIFY_ARRAY_STATE 3 /* atomic context wants to notify userspace */
int ro;
--- /dev/null
+/*
+ * Support for TI bq24022 (bqTINY-II) Dual Input (USB/AC Adpater)
+ * 1-Cell Li-Ion Charger connected via GPIOs.
+ *
+ * Copyright (c) 2008 Philipp Zabel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/**
+ * bq24022_mach_info - platform data for bq24022
+ * @gpio_nce: GPIO line connected to the nCE pin, used to enable / disable charging
+ * @gpio_iset2: GPIO line connected to the ISET2 pin, used to limit charging current to 100 mA / 500 mA
+ */
+struct bq24022_mach_info {
+ int gpio_nce;
+ int gpio_iset2;
+};
--- /dev/null
+/*
+ * consumer.h -- SoC Regulator consumer support.
+ *
+ * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Regulator Consumer Interface.
+ *
+ * A Power Management Regulator framework for SoC based devices.
+ * Features:-
+ * o Voltage and current level control.
+ * o Operating mode control.
+ * o Regulator status.
+ * o sysfs entries for showing client devices and status
+ *
+ * EXPERIMENTAL FEATURES:
+ * Dynamic Regulator operating Mode Switching (DRMS) - allows regulators
+ * to use most efficient operating mode depending upon voltage and load and
+ * is transparent to client drivers.
+ *
+ * e.g. Devices x,y,z share regulator r. Device x and y draw 20mA each during
+ * IO and 1mA at idle. Device z draws 100mA when under load and 5mA when
+ * idling. Regulator r has > 90% efficiency in NORMAL mode at loads > 100mA
+ * but this drops rapidly to 60% when below 100mA. Regulator r has > 90%
+ * efficiency in IDLE mode at loads < 10mA. Thus regulator r will operate
+ * in normal mode for loads > 10mA and in IDLE mode for load <= 10mA.
+ *
+ */
+
+#ifndef __LINUX_REGULATOR_CONSUMER_H_
+#define __LINUX_REGULATOR_CONSUMER_H_
+
+/*
+ * Regulator operating modes.
+ *
+ * Regulators can run in a variety of different operating modes depending on
+ * output load. This allows further system power savings by selecting the
+ * best (and most efficient) regulator mode for a desired load.
+ *
+ * Most drivers will only care about NORMAL. The modes below are generic and
+ * will probably not match the naming convention of your regulator data sheet
+ * but should match the use cases in the datasheet.
+ *
+ * In order of power efficiency (least efficient at top).
+ *
+ * Mode Description
+ * FAST Regulator can handle fast changes in it's load.
+ * e.g. useful in CPU voltage & frequency scaling where
+ * load can quickly increase with CPU frequency increases.
+ *
+ * NORMAL Normal regulator power supply mode. Most drivers will
+ * use this mode.
+ *
+ * IDLE Regulator runs in a more efficient mode for light
+ * loads. Can be used for devices that have a low power
+ * requirement during periods of inactivity. This mode
+ * may be more noisy than NORMAL and may not be able
+ * to handle fast load switching.
+ *
+ * STANDBY Regulator runs in the most efficient mode for very
+ * light loads. Can be used by devices when they are
+ * in a sleep/standby state. This mode is likely to be
+ * the most noisy and may not be able to handle fast load
+ * switching.
+ *
+ * NOTE: Most regulators will only support a subset of these modes. Some
+ * will only just support NORMAL.
+ *
+ * These modes can be OR'ed together to make up a mask of valid register modes.
+ */
+
+#define REGULATOR_MODE_FAST 0x1
+#define REGULATOR_MODE_NORMAL 0x2
+#define REGULATOR_MODE_IDLE 0x4
+#define REGULATOR_MODE_STANDBY 0x8
+
+/*
+ * Regulator notifier events.
+ *
+ * UNDER_VOLTAGE Regulator output is under voltage.
+ * OVER_CURRENT Regulator output current is too high.
+ * REGULATION_OUT Regulator output is out of regulation.
+ * FAIL Regulator output has failed.
+ * OVER_TEMP Regulator over temp.
+ * FORCE_DISABLE Regulator shut down by software.
+ *
+ * NOTE: These events can be OR'ed together when passed into handler.
+ */
+
+#define REGULATOR_EVENT_UNDER_VOLTAGE 0x01
+#define REGULATOR_EVENT_OVER_CURRENT 0x02
+#define REGULATOR_EVENT_REGULATION_OUT 0x04
+#define REGULATOR_EVENT_FAIL 0x08
+#define REGULATOR_EVENT_OVER_TEMP 0x10
+#define REGULATOR_EVENT_FORCE_DISABLE 0x20
+
+struct regulator;
+
+/**
+ * struct regulator_bulk_data - Data used for bulk regulator operations.
+ *
+ * @supply The name of the supply. Initialised by the user before
+ * using the bulk regulator APIs.
+ * @consumer The regulator consumer for the supply. This will be managed
+ * by the bulk API.
+ *
+ * The regulator APIs provide a series of regulator_bulk_() API calls as
+ * a convenience to consumers which require multiple supplies. This
+ * structure is used to manage data for these calls.
+ */
+struct regulator_bulk_data {
+ const char *supply;
+ struct regulator *consumer;
+};
+
+#if defined(CONFIG_REGULATOR)
+
+/* regulator get and put */
+struct regulator *__must_check regulator_get(struct device *dev,
+ const char *id);
+void regulator_put(struct regulator *regulator);
+
+/* regulator output control and status */
+int regulator_enable(struct regulator *regulator);
+int regulator_disable(struct regulator *regulator);
+int regulator_force_disable(struct regulator *regulator);
+int regulator_is_enabled(struct regulator *regulator);
+
+int regulator_bulk_get(struct device *dev, int num_consumers,
+ struct regulator_bulk_data *consumers);
+int regulator_bulk_enable(int num_consumers,
+ struct regulator_bulk_data *consumers);
+int regulator_bulk_disable(int num_consumers,
+ struct regulator_bulk_data *consumers);
+void regulator_bulk_free(int num_consumers,
+ struct regulator_bulk_data *consumers);
+
+int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV);
+int regulator_get_voltage(struct regulator *regulator);
+int regulator_set_current_limit(struct regulator *regulator,
+ int min_uA, int max_uA);
+int regulator_get_current_limit(struct regulator *regulator);
+
+int regulator_set_mode(struct regulator *regulator, unsigned int mode);
+unsigned int regulator_get_mode(struct regulator *regulator);
+int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);
+
+/* regulator notifier block */
+int regulator_register_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+int regulator_unregister_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+
+/* driver data - core doesn't touch */
+void *regulator_get_drvdata(struct regulator *regulator);
+void regulator_set_drvdata(struct regulator *regulator, void *data);
+
+#else
+
+/*
+ * Make sure client drivers will still build on systems with no software
+ * controllable voltage or current regulators.
+ */
+static inline struct regulator *__must_check regulator_get(struct device *dev,
+ const char *id)
+{
+ /* Nothing except the stubbed out regulator API should be
+ * looking at the value except to check if it is an error
+ * value so the actual return value doesn't matter.
+ */
+ return (struct regulator *)id;
+}
+static inline void regulator_put(struct regulator *regulator)
+{
+}
+
+static inline int regulator_enable(struct regulator *regulator)
+{
+ return 0;
+}
+
+static inline int regulator_disable(struct regulator *regulator)
+{
+ return 0;
+}
+
+static inline int regulator_is_enabled(struct regulator *regulator)
+{
+ return 1;
+}
+
+static inline int regulator_bulk_get(struct device *dev,
+ int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ return 0;
+}
+
+static inline int regulator_bulk_enable(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ return 0;
+}
+
+static inline int regulator_bulk_disable(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+ return 0;
+}
+
+static inline void regulator_bulk_free(int num_consumers,
+ struct regulator_bulk_data *consumers)
+{
+}
+
+static inline int regulator_set_voltage(struct regulator *regulator,
+ int min_uV, int max_uV)
+{
+ return 0;
+}
+
+static inline int regulator_get_voltage(struct regulator *regulator)
+{
+ return 0;
+}
+
+static inline int regulator_set_current_limit(struct regulator *regulator,
+ int min_uA, int max_uA)
+{
+ return 0;
+}
+
+static inline int regulator_get_current_limit(struct regulator *regulator)
+{
+ return 0;
+}
+
+static inline int regulator_set_mode(struct regulator *regulator,
+ unsigned int mode)
+{
+ return 0;
+}
+
+static inline unsigned int regulator_get_mode(struct regulator *regulator)
+{
+ return REGULATOR_MODE_NORMAL;
+}
+
+static inline int regulator_set_optimum_mode(struct regulator *regulator,
+ int load_uA)
+{
+ return REGULATOR_MODE_NORMAL;
+}
+
+static inline int regulator_register_notifier(struct regulator *regulator,
+ struct notifier_block *nb)
+{
+ return 0;
+}
+
+static inline int regulator_unregister_notifier(struct regulator *regulator,
+ struct notifier_block *nb)
+{
+ return 0;
+}
+
+static inline void *regulator_get_drvdata(struct regulator *regulator)
+{
+ return NULL;
+}
+
+static inline void regulator_set_drvdata(struct regulator *regulator,
+ void *data)
+{
+}
+
+#endif
+
+#endif
--- /dev/null
+/*
+ * driver.h -- SoC Regulator driver support.
+ *
+ * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Regulator Driver Interface.
+ */
+
+#ifndef __LINUX_REGULATOR_DRIVER_H_
+#define __LINUX_REGULATOR_DRIVER_H_
+
+#include <linux/device.h>
+#include <linux/regulator/consumer.h>
+
+struct regulator_constraints;
+struct regulator_dev;
+
+/**
+ * struct regulator_ops - regulator operations.
+ *
+ * This struct describes regulator operations.
+ */
+struct regulator_ops {
+
+ /* get/set regulator voltage */
+ int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV);
+ int (*get_voltage) (struct regulator_dev *);
+
+ /* get/set regulator current */
+ int (*set_current_limit) (struct regulator_dev *,
+ int min_uA, int max_uA);
+ int (*get_current_limit) (struct regulator_dev *);
+
+ /* enable/disable regulator */
+ int (*enable) (struct regulator_dev *);
+ int (*disable) (struct regulator_dev *);
+ int (*is_enabled) (struct regulator_dev *);
+
+ /* get/set regulator operating mode (defined in regulator.h) */
+ int (*set_mode) (struct regulator_dev *, unsigned int mode);
+ unsigned int (*get_mode) (struct regulator_dev *);
+
+ /* get most efficient regulator operating mode for load */
+ unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV,
+ int output_uV, int load_uA);
+
+ /* the operations below are for configuration of regulator state when
+ * it's parent PMIC enters a global STANBY/HIBERNATE state */
+
+ /* set regulator suspend voltage */
+ int (*set_suspend_voltage) (struct regulator_dev *, int uV);
+
+ /* enable/disable regulator in suspend state */
+ int (*set_suspend_enable) (struct regulator_dev *);
+ int (*set_suspend_disable) (struct regulator_dev *);
+
+ /* set regulator suspend operating mode (defined in regulator.h) */
+ int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
+};
+
+/*
+ * Regulators can either control voltage or current.
+ */
+enum regulator_type {
+ REGULATOR_VOLTAGE,
+ REGULATOR_CURRENT,
+};
+
+/**
+ * struct regulator_desc - Regulator descriptor
+ *
+ */
+struct regulator_desc {
+ const char *name;
+ int id;
+ struct regulator_ops *ops;
+ int irq;
+ enum regulator_type type;
+ struct module *owner;
+};
+
+
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+ void *reg_data);
+void regulator_unregister(struct regulator_dev *rdev);
+
+int regulator_notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data);
+
+void *rdev_get_drvdata(struct regulator_dev *rdev);
+int rdev_get_id(struct regulator_dev *rdev);
+
+#endif
--- /dev/null
+/*
+ * fixed.h
+ *
+ * Copyright 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ */
+
+#ifndef __REGULATOR_FIXED_H
+#define __REGULATOR_FIXED_H
+
+struct fixed_voltage_config {
+ const char *supply_name;
+ int microvolts;
+};
+
+#endif
--- /dev/null
+/*
+ * machine.h -- SoC Regulator support, machine/board driver API.
+ *
+ * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
+ *
+ * Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Regulator Machine/Board Interface.
+ */
+
+#ifndef __LINUX_REGULATOR_MACHINE_H_
+#define __LINUX_REGULATOR_MACHINE_H_
+
+#include <linux/regulator/consumer.h>
+#include <linux/suspend.h>
+
+struct regulator;
+
+/*
+ * Regulator operation constraint flags. These flags are used to enable
+ * certain regulator operations and can be OR'ed together.
+ *
+ * VOLTAGE: Regulator output voltage can be changed by software on this
+ * board/machine.
+ * CURRENT: Regulator output current can be changed by software on this
+ * board/machine.
+ * MODE: Regulator operating mode can be changed by software on this
+ * board/machine.
+ * STATUS: Regulator can be enabled and disabled.
+ * DRMS: Dynamic Regulator Mode Switching is enabled for this regulator.
+ */
+
+#define REGULATOR_CHANGE_VOLTAGE 0x1
+#define REGULATOR_CHANGE_CURRENT 0x2
+#define REGULATOR_CHANGE_MODE 0x4
+#define REGULATOR_CHANGE_STATUS 0x8
+#define REGULATOR_CHANGE_DRMS 0x10
+
+/**
+ * struct regulator_state - regulator state during low power syatem states
+ *
+ * This describes a regulators state during a system wide low power state.
+ */
+struct regulator_state {
+ int uV; /* suspend voltage */
+ unsigned int mode; /* suspend regulator operating mode */
+ int enabled; /* is regulator enabled in this suspend state */
+};
+
+/**
+ * struct regulation_constraints - regulator operating constraints.
+ *
+ * This struct describes regulator and board/machine specific constraints.
+ */
+struct regulation_constraints {
+
+ char *name;
+
+ /* voltage output range (inclusive) - for voltage control */
+ int min_uV;
+ int max_uV;
+
+ /* current output range (inclusive) - for current control */
+ int min_uA;
+ int max_uA;
+
+ /* valid regulator operating modes for this machine */
+ unsigned int valid_modes_mask;
+
+ /* valid operations for regulator on this machine */
+ unsigned int valid_ops_mask;
+
+ /* regulator input voltage - only if supply is another regulator */
+ int input_uV;
+
+ /* regulator suspend states for global PMIC STANDBY/HIBERNATE */
+ struct regulator_state state_disk;
+ struct regulator_state state_mem;
+ struct regulator_state state_standby;
+ suspend_state_t initial_state; /* suspend state to set at init */
+
+ /* constriant flags */
+ unsigned always_on:1; /* regulator never off when system is on */
+ unsigned boot_on:1; /* bootloader/firmware enabled regulator */
+ unsigned apply_uV:1; /* apply uV constraint iff min == max */
+};
+
+int regulator_set_supply(const char *regulator, const char *regulator_supply);
+
+const char *regulator_get_supply(const char *regulator);
+
+int regulator_set_machine_constraints(const char *regulator,
+ struct regulation_constraints *constraints);
+
+int regulator_set_device_supply(const char *regulator, struct device *dev,
+ const char *supply);
+
+int regulator_suspend_prepare(suspend_state_t state);
+
+#endif
* @user_claim_unsupported: Whether the hardware supports exclusive
* RF-kill control by userspace. Set this before registering.
* @user_claim: Set when the switch is controlled exlusively by userspace.
- * @mutex: Guards switch state transitions
+ * @mutex: Guards switch state transitions. It serializes callbacks
+ * and also protects the state.
* @data: Pointer to the RF button drivers private data which will be
* passed along when toggling radio state.
* @toggle_radio(): Mandatory handler to control state of the radio.
const char *name;
enum rfkill_type type;
- enum rfkill_state state;
bool user_claim_unsupported;
bool user_claim;
+ /* the mutex serializes callbacks and also protects
+ * the state */
struct mutex mutex;
-
+ enum rfkill_state state;
void *data;
int (*toggle_radio)(void *data, enum rfkill_state state);
int (*get_state)(void *data, enum rfkill_state *state);
* @tc_index: Traffic control index
* @tc_verd: traffic control verdict
* @ndisc_nodetype: router type (from link layer)
+ * @do_not_encrypt: set to prevent encryption of this frame
* @dma_cookie: a cookie to one of several possible DMA operations
* done by skb DMA functions
* @secmark: security marking
#ifdef CONFIG_IPV6_NDISC_NODETYPE
__u8 ndisc_nodetype:2;
#endif
- /* 14 bit hole */
+#if defined(CONFIG_MAC80211) || defined(CONFIG_MAC80211_MODULE)
+ __u8 do_not_encrypt:1;
+#endif
+ /* 0/13/14 bit hole */
#ifdef CONFIG_NET_DMA
dma_cookie_t dma_cookie;
LINUX_MIB_TCPDSACKIGNOREDOLD, /* TCPSACKIgnoredOld */
LINUX_MIB_TCPDSACKIGNOREDNOUNDO, /* TCPSACKIgnoredNoUndo */
LINUX_MIB_TCPSPURIOUSRTOS, /* TCPSpuriousRTOs */
+ LINUX_MIB_TCPMD5NOTFOUND, /* TCPMD5NotFound */
+ LINUX_MIB_TCPMD5UNEXPECTED, /* TCPMD5Unexpected */
__LINUX_MIB_MAX
};
--- /dev/null
+/*
+ * orion_spi.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __LINUX_SPI_ORION_SPI_H
+#define __LINUX_SPI_ORION_SPI_H
+
+struct orion_spi_info {
+ u32 tclk; /* no <linux/clk.h> support yet */
+};
+
+
+#endif
unsigned long clone_flags,
pid_t pid, struct task_struct *child)
{
- if (unlikely(trace)) {
+ if (unlikely(trace) || unlikely(clone_flags & CLONE_PTRACE)) {
/*
* The child starts up with an immediate SIGSTOP.
*/
return notify || (current->ptrace & PT_PTRACED);
}
+#define DEATH_REAP -1
+#define DEATH_DELAYED_GROUP_LEADER -2
+
/**
* tracehook_notify_death - task is dead, ready to notify parent
* @task: @current task now exiting
* @death_cookie: value to pass to tracehook_report_death()
* @group_dead: nonzero if this was the last thread in the group to die
*
- * Return the signal number to send our parent with do_notify_parent(), or
- * zero to send no signal and leave a zombie, or -1 to self-reap right now.
+ * A return value >= 0 means call do_notify_parent() with that signal
+ * number. Negative return value can be %DEATH_REAP to self-reap right
+ * now, or %DEATH_DELAYED_GROUP_LEADER to a zombie without notifying our
+ * parent. Note that a return value of 0 means a do_notify_parent() call
+ * that sends no signal, but still wakes up a parent blocked in wait*().
*
* Called with write_lock_irq(&tasklist_lock) held.
*/
void **death_cookie, int group_dead)
{
if (task->exit_signal == -1)
- return task->ptrace ? SIGCHLD : -1;
+ return task->ptrace ? SIGCHLD : DEATH_REAP;
/*
* If something other than our normal parent is ptracing us, then
if (thread_group_empty(task) && !ptrace_reparented(task))
return task->exit_signal;
- return task->ptrace ? SIGCHLD : 0;
+ return task->ptrace ? SIGCHLD : DEATH_DELAYED_GROUP_LEADER;
}
/**
* tracehook_report_death - task is dead and ready to be reaped
* @task: @current task now exiting
- * @signal: signal number sent to parent, or 0 or -1
+ * @signal: return value from tracheook_notify_death()
* @death_cookie: value passed back from tracehook_notify_death()
* @group_dead: nonzero if this was the last thread in the group to die
*
* Thread has just become a zombie or is about to self-reap. If positive,
* @signal is the signal number just sent to the parent (usually %SIGCHLD).
- * If @signal is -1, this thread will self-reap. If @signal is 0, this is
- * a delayed_group_leader() zombie. The @death_cookie was passed back by
- * tracehook_notify_death().
+ * If @signal is %DEATH_REAP, this thread will self-reap. If @signal is
+ * %DEATH_DELAYED_GROUP_LEADER, this is a delayed_group_leader() zombie.
+ * The @death_cookie was passed back by tracehook_notify_death().
*
* If normal reaping is not inhibited, @task->exit_state might be changing
* in parallel.
int con_copy_unimap(struct vc_data *dst_vc, struct vc_data *src_vc);
#define vc_translate(vc, c) ((vc)->vc_translate[(c) | \
- (vc)->vc_toggle_meta ? 0x80 : 0])
+ ((vc)->vc_toggle_meta ? 0x80 : 0)])
#else
#define con_set_trans_old(arg) (0)
#define con_get_trans_old(arg) (-EINVAL)
#define con_copy_unimap(d, s) (0)
#define con_get_unimap(vc, ct, uct, list) (-EINVAL)
#define con_free_unimap(vc) do { ; } while (0)
+#define con_protect_unimap(vc, rdonly) do { ; } while (0)
#define vc_translate(vc, c) (c)
#endif
#include <linux/videodev2.h>
#include <media/videobuf-core.h>
+#include <linux/pm.h>
struct soc_camera_device {
struct list_head list;
struct module *owner;
int (*add)(struct soc_camera_device *);
void (*remove)(struct soc_camera_device *);
+ int (*suspend)(struct soc_camera_device *, pm_message_t state);
+ int (*resume)(struct soc_camera_device *);
int (*set_fmt_cap)(struct soc_camera_device *, __u32,
struct v4l2_rect *);
int (*try_fmt_cap)(struct soc_camera_device *, struct v4l2_format *);
struct module *owner;
int (*probe)(struct soc_camera_device *);
void (*remove)(struct soc_camera_device *);
+ int (*suspend)(struct soc_camera_device *, pm_message_t state);
+ int (*resume)(struct soc_camera_device *);
int (*init)(struct soc_camera_device *);
int (*release)(struct soc_camera_device *);
int (*start_capture)(struct soc_camera_device *);
/* Input packet from network to transport. */
static inline int dst_input(struct sk_buff *skb)
{
- int err;
-
- for (;;) {
- err = skb->dst->input(skb);
-
- if (likely(err == 0))
- return err;
- /* Oh, Jamal... Seems, I will not forgive you this mess. :-) */
- if (unlikely(err != NET_XMIT_BYPASS))
- return err;
- }
+ return skb->dst->input(skb);
}
static inline struct dst_entry *dst_check(struct dst_entry *dst, u32 cookie)
#define fl4_scope nl_u.ip4_u.scope
__u8 proto;
- __u8 flags;
union {
struct {
__be16 sport;
* data structure and functionality definitions
*/
-#ifndef _IP_VS_H
-#define _IP_VS_H
-
-#include <asm/types.h> /* For __uXX types */
-#include <linux/types.h> /* For __beXX types in userland */
-
-#include <linux/sysctl.h> /* For ctl_path */
-
-#define IP_VS_VERSION_CODE 0x010201
-#define NVERSION(version) \
- (version >> 16) & 0xFF, \
- (version >> 8) & 0xFF, \
- version & 0xFF
-
-/*
- * Virtual Service Flags
- */
-#define IP_VS_SVC_F_PERSISTENT 0x0001 /* persistent port */
-#define IP_VS_SVC_F_HASHED 0x0002 /* hashed entry */
-
-/*
- * Destination Server Flags
- */
-#define IP_VS_DEST_F_AVAILABLE 0x0001 /* server is available */
-#define IP_VS_DEST_F_OVERLOAD 0x0002 /* server is overloaded */
-
-/*
- * IPVS sync daemon states
- */
-#define IP_VS_STATE_NONE 0x0000 /* daemon is stopped */
-#define IP_VS_STATE_MASTER 0x0001 /* started as master */
-#define IP_VS_STATE_BACKUP 0x0002 /* started as backup */
-
-/*
- * IPVS socket options
- */
-#define IP_VS_BASE_CTL (64+1024+64) /* base */
-
-#define IP_VS_SO_SET_NONE IP_VS_BASE_CTL /* just peek */
-#define IP_VS_SO_SET_INSERT (IP_VS_BASE_CTL+1)
-#define IP_VS_SO_SET_ADD (IP_VS_BASE_CTL+2)
-#define IP_VS_SO_SET_EDIT (IP_VS_BASE_CTL+3)
-#define IP_VS_SO_SET_DEL (IP_VS_BASE_CTL+4)
-#define IP_VS_SO_SET_FLUSH (IP_VS_BASE_CTL+5)
-#define IP_VS_SO_SET_LIST (IP_VS_BASE_CTL+6)
-#define IP_VS_SO_SET_ADDDEST (IP_VS_BASE_CTL+7)
-#define IP_VS_SO_SET_DELDEST (IP_VS_BASE_CTL+8)
-#define IP_VS_SO_SET_EDITDEST (IP_VS_BASE_CTL+9)
-#define IP_VS_SO_SET_TIMEOUT (IP_VS_BASE_CTL+10)
-#define IP_VS_SO_SET_STARTDAEMON (IP_VS_BASE_CTL+11)
-#define IP_VS_SO_SET_STOPDAEMON (IP_VS_BASE_CTL+12)
-#define IP_VS_SO_SET_RESTORE (IP_VS_BASE_CTL+13)
-#define IP_VS_SO_SET_SAVE (IP_VS_BASE_CTL+14)
-#define IP_VS_SO_SET_ZERO (IP_VS_BASE_CTL+15)
-#define IP_VS_SO_SET_MAX IP_VS_SO_SET_ZERO
-
-#define IP_VS_SO_GET_VERSION IP_VS_BASE_CTL
-#define IP_VS_SO_GET_INFO (IP_VS_BASE_CTL+1)
-#define IP_VS_SO_GET_SERVICES (IP_VS_BASE_CTL+2)
-#define IP_VS_SO_GET_SERVICE (IP_VS_BASE_CTL+3)
-#define IP_VS_SO_GET_DESTS (IP_VS_BASE_CTL+4)
-#define IP_VS_SO_GET_DEST (IP_VS_BASE_CTL+5) /* not used now */
-#define IP_VS_SO_GET_TIMEOUT (IP_VS_BASE_CTL+6)
-#define IP_VS_SO_GET_DAEMON (IP_VS_BASE_CTL+7)
-#define IP_VS_SO_GET_MAX IP_VS_SO_GET_DAEMON
-
-
-/*
- * IPVS Connection Flags
- */
-#define IP_VS_CONN_F_FWD_MASK 0x0007 /* mask for the fwd methods */
-#define IP_VS_CONN_F_MASQ 0x0000 /* masquerading/NAT */
-#define IP_VS_CONN_F_LOCALNODE 0x0001 /* local node */
-#define IP_VS_CONN_F_TUNNEL 0x0002 /* tunneling */
-#define IP_VS_CONN_F_DROUTE 0x0003 /* direct routing */
-#define IP_VS_CONN_F_BYPASS 0x0004 /* cache bypass */
-#define IP_VS_CONN_F_SYNC 0x0020 /* entry created by sync */
-#define IP_VS_CONN_F_HASHED 0x0040 /* hashed entry */
-#define IP_VS_CONN_F_NOOUTPUT 0x0080 /* no output packets */
-#define IP_VS_CONN_F_INACTIVE 0x0100 /* not established */
-#define IP_VS_CONN_F_OUT_SEQ 0x0200 /* must do output seq adjust */
-#define IP_VS_CONN_F_IN_SEQ 0x0400 /* must do input seq adjust */
-#define IP_VS_CONN_F_SEQ_MASK 0x0600 /* in/out sequence mask */
-#define IP_VS_CONN_F_NO_CPORT 0x0800 /* no client port set yet */
-#define IP_VS_CONN_F_TEMPLATE 0x1000 /* template, not connection */
-
-/* Move it to better place one day, for now keep it unique */
-#define NFC_IPVS_PROPERTY 0x10000
-
-#define IP_VS_SCHEDNAME_MAXLEN 16
-#define IP_VS_IFNAME_MAXLEN 16
-
-
-/*
- * The struct ip_vs_service_user and struct ip_vs_dest_user are
- * used to set IPVS rules through setsockopt.
- */
-struct ip_vs_service_user {
- /* virtual service addresses */
- u_int16_t protocol;
- __be32 addr; /* virtual ip address */
- __be16 port;
- u_int32_t fwmark; /* firwall mark of service */
-
- /* virtual service options */
- char sched_name[IP_VS_SCHEDNAME_MAXLEN];
- unsigned flags; /* virtual service flags */
- unsigned timeout; /* persistent timeout in sec */
- __be32 netmask; /* persistent netmask */
-};
-
-
-struct ip_vs_dest_user {
- /* destination server address */
- __be32 addr;
- __be16 port;
-
- /* real server options */
- unsigned conn_flags; /* connection flags */
- int weight; /* destination weight */
-
- /* thresholds for active connections */
- u_int32_t u_threshold; /* upper threshold */
- u_int32_t l_threshold; /* lower threshold */
-};
-
-
-/*
- * IPVS statistics object (for user space)
- */
-struct ip_vs_stats_user
-{
- __u32 conns; /* connections scheduled */
- __u32 inpkts; /* incoming packets */
- __u32 outpkts; /* outgoing packets */
- __u64 inbytes; /* incoming bytes */
- __u64 outbytes; /* outgoing bytes */
-
- __u32 cps; /* current connection rate */
- __u32 inpps; /* current in packet rate */
- __u32 outpps; /* current out packet rate */
- __u32 inbps; /* current in byte rate */
- __u32 outbps; /* current out byte rate */
-};
-
-
-/* The argument to IP_VS_SO_GET_INFO */
-struct ip_vs_getinfo {
- /* version number */
- unsigned int version;
-
- /* size of connection hash table */
- unsigned int size;
-
- /* number of virtual services */
- unsigned int num_services;
-};
-
-
-/* The argument to IP_VS_SO_GET_SERVICE */
-struct ip_vs_service_entry {
- /* which service: user fills in these */
- u_int16_t protocol;
- __be32 addr; /* virtual address */
- __be16 port;
- u_int32_t fwmark; /* firwall mark of service */
-
- /* service options */
- char sched_name[IP_VS_SCHEDNAME_MAXLEN];
- unsigned flags; /* virtual service flags */
- unsigned timeout; /* persistent timeout */
- __be32 netmask; /* persistent netmask */
-
- /* number of real servers */
- unsigned int num_dests;
-
- /* statistics */
- struct ip_vs_stats_user stats;
-};
-
-
-struct ip_vs_dest_entry {
- __be32 addr; /* destination address */
- __be16 port;
- unsigned conn_flags; /* connection flags */
- int weight; /* destination weight */
-
- u_int32_t u_threshold; /* upper threshold */
- u_int32_t l_threshold; /* lower threshold */
-
- u_int32_t activeconns; /* active connections */
- u_int32_t inactconns; /* inactive connections */
- u_int32_t persistconns; /* persistent connections */
-
- /* statistics */
- struct ip_vs_stats_user stats;
-};
-
-
-/* The argument to IP_VS_SO_GET_DESTS */
-struct ip_vs_get_dests {
- /* which service: user fills in these */
- u_int16_t protocol;
- __be32 addr; /* virtual address */
- __be16 port;
- u_int32_t fwmark; /* firwall mark of service */
-
- /* number of real servers */
- unsigned int num_dests;
-
- /* the real servers */
- struct ip_vs_dest_entry entrytable[0];
-};
-
-
-/* The argument to IP_VS_SO_GET_SERVICES */
-struct ip_vs_get_services {
- /* number of virtual services */
- unsigned int num_services;
-
- /* service table */
- struct ip_vs_service_entry entrytable[0];
-};
-
-
-/* The argument to IP_VS_SO_GET_TIMEOUT */
-struct ip_vs_timeout_user {
- int tcp_timeout;
- int tcp_fin_timeout;
- int udp_timeout;
-};
-
-
-/* The argument to IP_VS_SO_GET_DAEMON */
-struct ip_vs_daemon_user {
- /* sync daemon state (master/backup) */
- int state;
-
- /* multicast interface name */
- char mcast_ifn[IP_VS_IFNAME_MAXLEN];
-
- /* SyncID we belong to */
- int syncid;
-};
+#ifndef _NET_IP_VS_H
+#define _NET_IP_VS_H
+#include <linux/ip_vs.h> /* definitions shared with userland */
+/* old ipvsadm versions still include this file directly */
#ifdef __KERNEL__
+#include <asm/types.h> /* for __uXX types */
+
+#include <linux/sysctl.h> /* for ctl_path */
#include <linux/list.h> /* for struct list_head */
#include <linux/spinlock.h> /* for struct rwlock_t */
#include <asm/atomic.h> /* for struct atomic_t */
#endif /* __KERNEL__ */
-#endif /* _IP_VS_H */
+#endif /* _NET_IP_VS_H */
* @aid: association ID number, valid only when @assoc is true
* @use_cts_prot: use CTS protection
* @use_short_preamble: use 802.11b short preamble
+ * @dtim_period: num of beacons before the next DTIM, for PSM
* @timestamp: beacon timestamp
* @beacon_int: beacon interval
- * @assoc_capability: capabbilities taken from assoc resp
+ * @assoc_capability: capabilities taken from assoc resp
* @assoc_ht: association in HT mode
* @ht_conf: ht capabilities
* @ht_bss_conf: ht extended capabilities
/* erp related data */
bool use_cts_prot;
bool use_short_preamble;
+ u8 dtim_period;
u16 beacon_int;
u16 assoc_capability;
u64 timestamp;
* These flags are used with the @flags member of &ieee80211_tx_info.
*
* @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
- * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption;
- * e.g., for EAPOL frame
* @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame
* @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
* for combined 802.11g / 802.11b networks)
* @IEEE80211_TX_CTL_SHORT_PREAMBLE: TBD
* @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
* through set_retry_limit configured long retry value
- * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211
* @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
* @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
* @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
*/
enum mac80211_tx_control_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
- IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1),
IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2),
IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3),
IEEE80211_TX_CTL_NO_ACK = BIT(4),
IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8),
IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9),
IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10),
- IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11),
IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12),
IEEE80211_TX_CTL_AMPDU = BIT(13),
IEEE80211_TX_CTL_OFDM_HT = BIT(14),
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
unsigned long jiffies;
- int ifindex;
u16 aid;
s8 rts_cts_rate_idx, alt_retry_rate_idx;
u8 retry_limit;
* @radio_enabled: when zero, driver is required to switch off the radio.
* TODO make a flag
* @beacon_int: beacon interval (TODO make interface config)
+ * @listen_interval: listen interval in units of beacon interval
* @flags: configuration flags defined above
* @power_level: requested transmit power (in dBm)
* @max_antenna_gain: maximum antenna gain (in dBi)
int radio_enabled;
int beacon_int;
+ u16 listen_interval;
u32 flags;
int power_level;
int max_antenna_gain;
* Measurement, Channel Switch, Quieting, TPC
*/
enum ieee80211_hw_flags {
- IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
* @max_signal: Maximum value for signal (rssi) in RX information, used
* only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
+ * @max_listen_interval: max listen interval in units of beacon interval
+ * that HW supports
+ *
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
* queues need to have configurable access parameters.
unsigned int extra_tx_headroom;
int channel_change_time;
int vif_data_size;
- u16 queues, ampdu_queues;
+ u16 queues;
+ u16 ampdu_queues;
+ u16 max_listen_interval;
s8 max_signal;
};
struct kmem_cache *slab;
int (*rtx_syn_ack)(struct sock *sk,
struct request_sock *req);
- void (*send_ack)(struct sk_buff *skb,
+ void (*send_ack)(struct sock *sk, struct sk_buff *skb,
struct request_sock *req);
void (*send_reset)(struct sock *sk,
struct sk_buff *skb);
return qdisc->dev_queue->qdisc;
}
+/* The qdisc root lock is a mechanism by which to top level
+ * of a qdisc tree can be locked from any qdisc node in the
+ * forest. This allows changing the configuration of some
+ * aspect of the qdisc tree while blocking out asynchronous
+ * qdisc access in the packet processing paths.
+ *
+ * It is only legal to do this when the root will not change
+ * on us. Otherwise we'll potentially lock the wrong qdisc
+ * root. This is enforced by holding the RTNL semaphore, which
+ * all users of this lock accessor must do.
+ */
static inline spinlock_t *qdisc_root_lock(struct Qdisc *qdisc)
{
struct Qdisc *root = qdisc_root(qdisc);
+ ASSERT_RTNL();
return qdisc_lock(root);
}
return qdisc_skb_cb(skb)->pkt_len;
}
+/* additional qdisc xmit flags (NET_XMIT_MASK in linux/netdevice.h) */
+enum net_xmit_qdisc_t {
+ __NET_XMIT_STOLEN = 0x00010000,
+ __NET_XMIT_BYPASS = 0x00020000,
+};
+
+#ifdef CONFIG_NET_CLS_ACT
+#define net_xmit_drop_count(e) ((e) & __NET_XMIT_STOLEN ? 0 : 1)
+#else
+#define net_xmit_drop_count(e) (1)
+#endif
+
static inline int qdisc_enqueue(struct sk_buff *skb, struct Qdisc *sch)
{
#ifdef CONFIG_NET_SCHED
static inline int qdisc_enqueue_root(struct sk_buff *skb, struct Qdisc *sch)
{
qdisc_skb_cb(skb)->pkt_len = skb->len;
- return qdisc_enqueue(skb, sch);
+ return qdisc_enqueue(skb, sch) & NET_XMIT_MASK;
}
static inline int __qdisc_enqueue_tail(struct sk_buff *skb, struct Qdisc *sch,
*/
struct sctp_af {
int (*sctp_xmit) (struct sk_buff *skb,
- struct sctp_transport *,
- int ipfragok);
+ struct sctp_transport *);
int (*setsockopt) (struct sock *sk,
int level,
int optname,
u32 pp_rseq; /* remote sequence number */
struct slcp lcp; /* LCP params */
struct sipcp ipcp; /* IPCP params */
- u32 ibytes,obytes; /* Bytes in/out */
- u32 ipkts,opkts; /* Packets in/out */
struct timer_list pp_timer;
struct net_device *pp_if;
char pp_link_state; /* Link status */
};
struct rdma_addr {
- struct sockaddr src_addr;
- u8 src_pad[sizeof(struct sockaddr_in6) -
- sizeof(struct sockaddr)];
- struct sockaddr dst_addr;
- u8 dst_pad[sizeof(struct sockaddr_in6) -
- sizeof(struct sockaddr)];
+ struct sockaddr_storage src_addr;
+ struct sockaddr_storage dst_addr;
struct rdma_dev_addr dev_addr;
};
struct snd_soc_dapm_pin;
struct snd_soc_dapm_route;
+int dapm_reg_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event);
+
/* dapm controls */
int snd_soc_dapm_put_volsw(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol);
/* DSTCACHE_CTLSTAT bit constants */
-#define RB2D_DC_FLUSH (3 << 0)
-#define RB2D_DC_FLUSH_ALL 0xf
+#define RB2D_DC_FLUSH_2D (1 << 0)
+#define RB2D_DC_FREE_2D (1 << 2)
+#define RB2D_DC_FLUSH_ALL (RB2D_DC_FLUSH_2D | RB2D_DC_FREE_2D)
#define RB2D_DC_BUSY (1 << 31)
Enabling this option will pass "-Os" instead of "-O2" to gcc
resulting in a smaller kernel.
- If unsure, say N.
+ If unsure, say Y.
config SYSCTL
bool
If unsure, say Y.
+if MODULES
+
config MODULE_FORCE_LOAD
bool "Forced module loading"
- depends on MODULES
default n
help
Allow loading of modules without version information (ie. modprobe
config MODULE_UNLOAD
bool "Module unloading"
- depends on MODULES
help
Without this option you will not be able to unload any
modules (note that some modules may not be unloadable
config MODVERSIONS
bool "Module versioning support"
- depends on MODULES
help
Usually, you have to use modules compiled with your kernel.
Saying Y here makes it sometimes possible to use modules
config MODULE_SRCVERSION_ALL
bool "Source checksum for all modules"
- depends on MODULES
help
Modules which contain a MODULE_VERSION get an extra "srcversion"
field inserted into their modinfo section, which contains a
config KMOD
def_bool y
- depends on MODULES
help
This is being removed soon. These days, CONFIG_MODULES
implies CONFIG_KMOD, so use that instead.
+endif # MODULES
+
config STOP_MACHINE
bool
default y
loops_per_jiffy &= ~loopbit;
}
}
- printk(KERN_INFO "%lu.%02lu BogoMIPS (lpj=%lu)\n",
+ printk(KERN_CONT "%lu.%02lu BogoMIPS (lpj=%lu)\n",
loops_per_jiffy/(500000/HZ),
(loops_per_jiffy/(5000/HZ)) % 100, loops_per_jiffy);
}
#include <linux/init.h>
#include <linux/smp_lock.h>
#include <linux/initrd.h>
-#include <linux/hdreg.h>
#include <linux/bootmem.h>
#include <linux/tty.h>
#include <linux/gfp.h>
#ifdef CONFIG_BLK_DEV_INITRD
if (initrd_start && !initrd_below_start_ok &&
- page_to_pfn(virt_to_page(initrd_start)) < min_low_pfn) {
+ page_to_pfn(virt_to_page((void *)initrd_start)) < min_low_pfn) {
printk(KERN_CRIT "initrd overwritten (0x%08lx < 0x%08lx) - "
"disabling it.\n",
- page_to_pfn(virt_to_page(initrd_start)), min_low_pfn);
+ page_to_pfn(virt_to_page((void *)initrd_start)),
+ min_low_pfn);
initrd_start = 0;
}
#endif
if (status_get->mask & AUDIT_STATUS_ENABLED) {
err = audit_set_enabled(status_get->enabled,
loginuid, sessionid, sid);
- if (err < 0) return err;
+ if (err < 0)
+ return err;
}
if (status_get->mask & AUDIT_STATUS_FAILURE) {
err = audit_set_failure(status_get->failure,
loginuid, sessionid, sid);
- if (err < 0) return err;
+ if (err < 0)
+ return err;
}
if (status_get->mask & AUDIT_STATUS_PID) {
int new_pid = status_get->pid;
audit_pid = new_pid;
audit_nlk_pid = NETLINK_CB(skb).pid;
}
- if (status_get->mask & AUDIT_STATUS_RATE_LIMIT)
+ if (status_get->mask & AUDIT_STATUS_RATE_LIMIT) {
err = audit_set_rate_limit(status_get->rate_limit,
loginuid, sessionid, sid);
+ if (err < 0)
+ return err;
+ }
if (status_get->mask & AUDIT_STATUS_BACKLOG_LIMIT)
err = audit_set_backlog_limit(status_get->backlog_limit,
loginuid, sessionid, sid);
{
const unsigned char *p;
for (p = string; p < (const unsigned char *)string + len && *p; p++) {
- if (*p == '"' || *p < 0x21 || *p > 0x7f)
+ if (*p == '"' || *p < 0x21 || *p > 0x7e)
return 1;
}
return 0;
struct audit_buffer *ab;
ab = audit_log_start(NULL, GFP_KERNEL,
AUDIT_CONFIG_CHANGE);
+ audit_log_format(ab, "auid=%u ses=%u",
+ audit_get_loginuid(current),
+ audit_get_sessionid(current));
audit_log_format(ab,
- "op=updated rules specifying path=");
+ " op=updated rules specifying path=");
audit_log_untrustedstring(ab, owatch->path);
audit_log_format(ab, " with dev=%u ino=%lu\n",
dev, ino);
struct audit_buffer *ab;
ab = audit_log_start(NULL, GFP_KERNEL,
AUDIT_CONFIG_CHANGE);
- audit_log_format(ab, "op=remove rule path=");
+ audit_log_format(ab, "auid=%u ses=%u",
+ audit_get_loginuid(current),
+ audit_get_sessionid(current));
+ audit_log_format(ab, " op=remove rule path=");
audit_log_untrustedstring(ab, w->path);
if (r->filterkey) {
audit_log_format(ab, " key=");
static int audit_match_perm(struct audit_context *ctx, int mask)
{
+ if (unlikely(!ctx))
+ return 0;
+
unsigned n = ctx->major;
switch (audit_classify_syscall(ctx->arch, n)) {
case 0: /* native */
{
unsigned index = which & ~S_IFMT;
mode_t mode = which & S_IFMT;
+
+ if (unlikely(!ctx))
+ return 0;
+
if (index >= ctx->name_count)
return 0;
if (ctx->names[index].ino == -1)
if (!result)
return 0;
}
- if (rule->filterkey)
+ if (rule->filterkey && ctx)
ctx->filterkey = kstrdup(rule->filterkey, GFP_ATOMIC);
switch (rule->action) {
case AUDIT_NEVER: *state = AUDIT_DISABLED; break;
struct audit_context *ctx = tsk->audit_context;
if (audit_pid && t->tgid == audit_pid) {
- if (sig == SIGTERM || sig == SIGHUP || sig == SIGUSR1) {
+ if (sig == SIGTERM || sig == SIGHUP || sig == SIGUSR1 || sig == SIGUSR2) {
audit_sig_pid = tsk->pid;
if (tsk->loginuid != -1)
audit_sig_uid = tsk->loginuid;
return NULL;
}
+static void free_cg_links(struct list_head *tmp)
+{
+ struct cg_cgroup_link *link;
+ struct cg_cgroup_link *saved_link;
+
+ list_for_each_entry_safe(link, saved_link, tmp, cgrp_link_list) {
+ list_del(&link->cgrp_link_list);
+ kfree(link);
+ }
+}
+
/*
* allocate_cg_links() allocates "count" cg_cgroup_link structures
* and chains them on tmp through their cgrp_link_list fields. Returns 0 on
static int allocate_cg_links(int count, struct list_head *tmp)
{
struct cg_cgroup_link *link;
- struct cg_cgroup_link *saved_link;
int i;
INIT_LIST_HEAD(tmp);
for (i = 0; i < count; i++) {
link = kmalloc(sizeof(*link), GFP_KERNEL);
if (!link) {
- list_for_each_entry_safe(link, saved_link, tmp,
- cgrp_link_list) {
- list_del(&link->cgrp_link_list);
- kfree(link);
- }
+ free_cg_links(tmp);
return -ENOMEM;
}
list_add(&link->cgrp_link_list, tmp);
return 0;
}
-static void free_cg_links(struct list_head *tmp)
-{
- struct cg_cgroup_link *link;
- struct cg_cgroup_link *saved_link;
-
- list_for_each_entry_safe(link, saved_link, tmp, cgrp_link_list) {
- list_del(&link->cgrp_link_list);
- kfree(link);
- }
-}
-
/*
* find_css_set() takes an existing cgroup group and a
* cgroup object, and returns a css_set object that's
struct super_block *sb;
struct cgroupfs_root *root;
struct list_head tmp_cg_links;
- INIT_LIST_HEAD(&tmp_cg_links);
/* First find the desired set of subsystems */
ret = parse_cgroupfs_options(data, &opts);
if (buffer == NULL)
return -ENOMEM;
}
- if (nbytes && copy_from_user(buffer, userbuf, nbytes))
- return -EFAULT;
+ if (nbytes && copy_from_user(buffer, userbuf, nbytes)) {
+ retval = -EFAULT;
+ goto out;
+ }
buffer[nbytes] = 0; /* nul-terminate */
strstrip(buffer);
retval = cft->write_string(cgrp, cft, buffer);
if (!retval)
retval = nbytes;
+out:
if (buffer != local_buffer)
kfree(buffer);
return retval;
return cgroup_create(c_parent, dentry, mode | S_IFDIR);
}
-static inline int cgroup_has_css_refs(struct cgroup *cgrp)
+static int cgroup_has_css_refs(struct cgroup *cgrp)
{
/* Check the reference count on each subsystem. Since we
* already established that there are no tasks in the
#include <asm/uaccess.h>
#include <asm/atomic.h>
#include <linux/mutex.h>
-#include <linux/kfifo.h>
#include <linux/workqueue.h>
#include <linux/cgroup.h>
static void
update_domain_attr(struct sched_domain_attr *dattr, struct cpuset *c)
{
- if (!dattr)
- return;
if (dattr->relax_domain_level < c->relax_domain_level)
dattr->relax_domain_level = c->relax_domain_level;
return;
}
+static void
+update_domain_attr_tree(struct sched_domain_attr *dattr, struct cpuset *c)
+{
+ LIST_HEAD(q);
+
+ list_add(&c->stack_list, &q);
+ while (!list_empty(&q)) {
+ struct cpuset *cp;
+ struct cgroup *cont;
+ struct cpuset *child;
+
+ cp = list_first_entry(&q, struct cpuset, stack_list);
+ list_del(q.next);
+
+ if (cpus_empty(cp->cpus_allowed))
+ continue;
+
+ if (is_sched_load_balance(cp))
+ update_domain_attr(dattr, cp);
+
+ list_for_each_entry(cont, &cp->css.cgroup->children, sibling) {
+ child = cgroup_cs(cont);
+ list_add_tail(&child->stack_list, &q);
+ }
+ }
+}
+
/*
* rebuild_sched_domains()
*
* So the reverse nesting would risk an ABBA deadlock.
*
* The three key local variables below are:
- * q - a kfifo queue of cpuset pointers, used to implement a
+ * q - a linked-list queue of cpuset pointers, used to implement a
* top-down scan of all cpusets. This scan loads a pointer
* to each cpuset marked is_sched_load_balance into the
* array 'csa'. For our purposes, rebuilding the schedulers
void rebuild_sched_domains(void)
{
- struct kfifo *q; /* queue of cpusets to be scanned */
+ LIST_HEAD(q); /* queue of cpusets to be scanned*/
struct cpuset *cp; /* scans q */
struct cpuset **csa; /* array of all cpuset ptrs */
int csn; /* how many cpuset ptrs in csa so far */
int ndoms; /* number of sched domains in result */
int nslot; /* next empty doms[] cpumask_t slot */
- q = NULL;
csa = NULL;
doms = NULL;
dattr = NULL;
dattr = kmalloc(sizeof(struct sched_domain_attr), GFP_KERNEL);
if (dattr) {
*dattr = SD_ATTR_INIT;
- update_domain_attr(dattr, &top_cpuset);
+ update_domain_attr_tree(dattr, &top_cpuset);
}
*doms = top_cpuset.cpus_allowed;
goto rebuild;
}
- q = kfifo_alloc(number_of_cpusets * sizeof(cp), GFP_KERNEL, NULL);
- if (IS_ERR(q))
- goto done;
csa = kmalloc(number_of_cpusets * sizeof(cp), GFP_KERNEL);
if (!csa)
goto done;
csn = 0;
- cp = &top_cpuset;
- __kfifo_put(q, (void *)&cp, sizeof(cp));
- while (__kfifo_get(q, (void *)&cp, sizeof(cp))) {
+ list_add(&top_cpuset.stack_list, &q);
+ while (!list_empty(&q)) {
struct cgroup *cont;
struct cpuset *child; /* scans child cpusets of cp */
+ cp = list_first_entry(&q, struct cpuset, stack_list);
+ list_del(q.next);
+
if (cpus_empty(cp->cpus_allowed))
continue;
- if (is_sched_load_balance(cp))
+ /*
+ * All child cpusets contain a subset of the parent's cpus, so
+ * just skip them, and then we call update_domain_attr_tree()
+ * to calc relax_domain_level of the corresponding sched
+ * domain.
+ */
+ if (is_sched_load_balance(cp)) {
csa[csn++] = cp;
+ continue;
+ }
list_for_each_entry(cont, &cp->css.cgroup->children, sibling) {
child = cgroup_cs(cont);
- __kfifo_put(q, (void *)&child, sizeof(cp));
+ list_add_tail(&child->stack_list, &q);
}
}
cpus_or(*dp, *dp, b->cpus_allowed);
b->pn = -1;
if (dattr)
- update_domain_attr(dattr
+ update_domain_attr_tree(dattr
+ nslot, b);
}
}
put_online_cpus();
done:
- if (q && !IS_ERR(q))
- kfifo_free(q);
kfree(csa);
/* Don't kfree(doms) -- partition_sched_domains() does that. */
/* Don't kfree(dattr) -- partition_sched_domains() does that. */
*/
static void scan_for_empty_cpusets(const struct cpuset *root)
{
+ LIST_HEAD(queue);
struct cpuset *cp; /* scans cpusets being updated */
struct cpuset *child; /* scans child cpusets of cp */
- struct list_head queue;
struct cgroup *cont;
nodemask_t oldmems;
- INIT_LIST_HEAD(&queue);
-
list_add_tail((struct list_head *)&root->stack_list, &queue);
while (!list_empty(&queue)) {
- cp = container_of(queue.next, struct cpuset, stack_list);
+ cp = list_first_entry(&queue, struct cpuset, stack_list);
list_del(queue.next);
list_for_each_entry(cont, &cp->css.cgroup->children, sibling) {
child = cgroup_cs(cont);
list_add_tail(&child->stack_list, &queue);
}
- cont = cp->css.cgroup;
/* Continue past cpusets with all cpus, mems online */
if (cpus_subset(cp->cpus_allowed, cpu_online_map) &&
{
struct dma_coherent_mem *mem = dev->dma_mem;
int pos, err;
- int pages = (size + (device_addr & ~PAGE_MASK) + PAGE_SIZE - 1);
- pages >>= PAGE_SHIFT;
+ size += device_addr & ~PAGE_MASK;
if (!mem)
return ERR_PTR(-EINVAL);
pos = (device_addr - mem->device_base) >> PAGE_SHIFT;
- err = bitmap_allocate_region(mem->bitmap, pos, get_order(pages));
+ err = bitmap_allocate_region(mem->bitmap, pos, get_order(size));
if (err != 0)
return ERR_PTR(err);
return mem->virt_base + (pos << PAGE_SHIFT);
tsk->exit_signal = SIGCHLD;
signal = tracehook_notify_death(tsk, &cookie, group_dead);
- if (signal > 0)
+ if (signal >= 0)
signal = do_notify_parent(tsk, signal);
- tsk->exit_state = signal < 0 ? EXIT_DEAD : EXIT_ZOMBIE;
+ tsk->exit_state = signal == DEATH_REAP ? EXIT_DEAD : EXIT_ZOMBIE;
/* mt-exec, de_thread() is waiting for us */
if (thread_group_leader(tsk) &&
tracehook_report_death(tsk, signal, cookie, group_dead);
/* If the process is dead, release it - nobody will wait for it */
- if (signal < 0)
+ if (signal == DEATH_REAP)
release_task(tsk);
}
ret = chip->set_type(irq, flags & IRQF_TRIGGER_MASK);
if (ret)
- pr_err("setting flow type for irq %u failed (%pF)\n",
+ pr_err("setting trigger mode %d for irq %u failed (%pF)\n",
+ (int)(flags & IRQF_TRIGGER_MASK),
irq, chip->set_type);
return ret;
static int kgdb_break_asap;
+#define KGDB_MAX_THREAD_QUERY 17
struct kgdb_state {
int ex_vector;
int signo;
int err_code;
int cpu;
int pass_exception;
+ unsigned long thr_query;
unsigned long threadid;
long kgdb_usethreadid;
struct pt_regs *linux_regs;
* Weak aliases for breakpoint management,
* can be overriden by architectures when needed:
*/
-int __weak kgdb_validate_break_address(unsigned long addr)
-{
- char tmp_variable[BREAK_INSTR_SIZE];
-
- return probe_kernel_read(tmp_variable, (char *)addr, BREAK_INSTR_SIZE);
-}
-
int __weak kgdb_arch_set_breakpoint(unsigned long addr, char *saved_instr)
{
int err;
(char *)bundle, BREAK_INSTR_SIZE);
}
+int __weak kgdb_validate_break_address(unsigned long addr)
+{
+ char tmp_variable[BREAK_INSTR_SIZE];
+ int err;
+ /* Validate setting the breakpoint and then removing it. In the
+ * remove fails, the kernel needs to emit a bad message because we
+ * are deep trouble not being able to put things back the way we
+ * found them.
+ */
+ err = kgdb_arch_set_breakpoint(addr, tmp_variable);
+ if (err)
+ return err;
+ err = kgdb_arch_remove_breakpoint(addr, tmp_variable);
+ if (err)
+ printk(KERN_ERR "KGDB: Critical breakpoint error, kernel "
+ "memory destroyed at: %lx", addr);
+ return err;
+}
+
unsigned long __weak kgdb_arch_pc(int exception, struct pt_regs *regs)
{
return instruction_pointer(regs);
{
int hex_val;
int num = 0;
+ int negate = 0;
*long_val = 0;
+ if (**ptr == '-') {
+ negate = 1;
+ (*ptr)++;
+ }
while (**ptr) {
hex_val = hex(**ptr);
if (hex_val < 0)
(*ptr)++;
}
+ if (negate)
+ *long_val = -*long_val;
+
return num;
}
static struct task_struct *getthread(struct pt_regs *regs, int tid)
{
/*
- * Non-positive TIDs are remapped idle tasks:
+ * Non-positive TIDs are remapped to the cpu shadow information
*/
- if (tid <= 0)
- return idle_task(-tid);
+ if (tid == 0 || tid == -1)
+ tid = -atomic_read(&kgdb_active) - 2;
+ if (tid < 0) {
+ if (kgdb_info[-tid - 2].task)
+ return kgdb_info[-tid - 2].task;
+ else
+ return idle_task(-tid - 2);
+ }
/*
* find_task_by_pid_ns() does not take the tasklist lock anymore
}
/*
- * Remap normal tasks to their real PID, idle tasks to -1 ... -NR_CPUs:
+ * Remap normal tasks to their real PID,
+ * CPU shadow threads are mapped to -CPU - 2
*/
static inline int shadow_pid(int realpid)
{
if (realpid)
return realpid;
- return -1-raw_smp_processor_id();
+ return -raw_smp_processor_id() - 2;
}
static char gdbmsgbuf[BUFMAX + 1];
local_debuggerinfo = kgdb_info[ks->cpu].debuggerinfo;
} else {
local_debuggerinfo = NULL;
- for (i = 0; i < NR_CPUS; i++) {
+ for_each_online_cpu(i) {
/*
* Try to find the task on some other
* or possibly this node if we do not
/* Handle the 'q' query packets */
static void gdb_cmd_query(struct kgdb_state *ks)
{
- struct task_struct *thread;
+ struct task_struct *g;
+ struct task_struct *p;
unsigned char thref[8];
char *ptr;
int i;
+ int cpu;
+ int finished = 0;
switch (remcom_in_buffer[1]) {
case 's':
break;
}
- if (remcom_in_buffer[1] == 'f')
- ks->threadid = 1;
-
+ i = 0;
remcom_out_buffer[0] = 'm';
ptr = remcom_out_buffer + 1;
-
- for (i = 0; i < 17; ks->threadid++) {
- thread = getthread(ks->linux_regs, ks->threadid);
- if (thread) {
- int_to_threadref(thref, ks->threadid);
+ if (remcom_in_buffer[1] == 'f') {
+ /* Each cpu is a shadow thread */
+ for_each_online_cpu(cpu) {
+ ks->thr_query = 0;
+ int_to_threadref(thref, -cpu - 2);
pack_threadid(ptr, thref);
ptr += BUF_THREAD_ID_SIZE;
*(ptr++) = ',';
i++;
}
}
+
+ do_each_thread(g, p) {
+ if (i >= ks->thr_query && !finished) {
+ int_to_threadref(thref, p->pid);
+ pack_threadid(ptr, thref);
+ ptr += BUF_THREAD_ID_SIZE;
+ *(ptr++) = ',';
+ ks->thr_query++;
+ if (ks->thr_query % KGDB_MAX_THREAD_QUERY == 0)
+ finished = 1;
+ }
+ i++;
+ } while_each_thread(g, p);
+
*(--ptr) = '\0';
break;
error_packet(remcom_out_buffer, -EINVAL);
break;
}
- if (ks->threadid > 0) {
+ if ((int)ks->threadid > 0) {
kgdb_mem2hex(getthread(ks->linux_regs,
ks->threadid)->comm,
remcom_out_buffer, 16);
} else {
static char tmpstr[23 + BUF_THREAD_ID_SIZE];
- sprintf(tmpstr, "Shadow task %d for pid 0",
- (int)(-ks->threadid-1));
+ sprintf(tmpstr, "shadowCPU%d",
+ (int)(-ks->threadid - 2));
kgdb_mem2hex(tmpstr, remcom_out_buffer, strlen(tmpstr));
}
break;
} else {
struct marker_probe_closure *multi;
int i;
+ /*
+ * Read mdata->ptype before mdata->multi.
+ */
+ smp_rmb();
+ multi = mdata->multi;
/*
* multi points to an array, therefore accessing the array
* depends on reading multi. However, even in this case,
* in the fast path, so put the explicit barrier here.
*/
smp_read_barrier_depends();
- multi = mdata->multi;
for (i = 0; multi[i].func; i++) {
va_start(args, call_private);
multi[i].func(multi[i].probe_private, call_private,
} else {
struct marker_probe_closure *multi;
int i;
+ /*
+ * Read mdata->ptype before mdata->multi.
+ */
+ smp_rmb();
+ multi = mdata->multi;
/*
* multi points to an array, therefore accessing the array
* depends on reading multi. However, even in this case,
* in the fast path, so put the explicit barrier here.
*/
smp_read_barrier_depends();
- multi = mdata->multi;
for (i = 0; multi[i].func; i++)
multi[i].func(multi[i].probe_private, call_private,
mdata->format, &args);
/***
* mutex_init - initialize the mutex
* @lock: the mutex to be initialized
+ * @key: the lock_class_key for the class; used by mutex lock debugging
*
* Initialize the mutex to unlocked state.
*
* requirement that the application has is cleaned up when closes the file
* pointer or exits the pm_qos_object will get an opportunity to clean up.
*
- * mark gross mgross@linux.intel.com
+ * Mark Gross <mgross@linux.intel.com>
*/
#include <linux/pm_qos_params.h>
* @value: defines the qos request
*
* This function inserts a new entry in the pm_qos_class list of requested qos
- * performance charactoistics. It recomputes the agregate QoS expectations for
- * the pm_qos_class of parrameters.
+ * performance characteristics. It recomputes the aggregate QoS expectations
+ * for the pm_qos_class of parameters.
*/
int pm_qos_add_requirement(int pm_qos_class, char *name, s32 value)
{
* @name: identifies the request
* @value: defines the qos request
*
- * Updates an existing qos requierement for the pm_qos_class of parameters along
+ * Updates an existing qos requirement for the pm_qos_class of parameters along
* with updating the target pm_qos_class value.
*
- * If the named request isn't in the lest then no change is made.
+ * If the named request isn't in the list then no change is made.
*/
int pm_qos_update_requirement(int pm_qos_class, char *name, s32 new_value)
{
* @pm_qos_class: identifies which list of qos request to us
* @name: identifies the request
*
- * Will remove named qos request from pm_qos_class list of parrameters and
+ * Will remove named qos request from pm_qos_class list of parameters and
* recompute the current target value for the pm_qos_class.
*/
void pm_qos_remove_requirement(int pm_qos_class, char *name)
* @notifier: notifier block managed by caller.
*
* will register the notifier into a notification chain that gets called
- * uppon changes to the pm_qos_class target value.
+ * upon changes to the pm_qos_class target value.
*/
int pm_qos_add_notifier(int pm_qos_class, struct notifier_block *notifier)
{
* @notifier: notifier block to be removed.
*
* will remove the notifier from the notification chain that gets called
- * uppon changes to the pm_qos_class target value.
+ * upon changes to the pm_qos_class target value.
*/
int pm_qos_remove_notifier(int pm_qos_class, struct notifier_block *notifier)
{
#if defined CONFIG_PRINTK
-DEFINE_RATELIMIT_STATE(printk_ratelimit_state, 5 * HZ, 10);
/*
* printk rate limiting, lifted from the networking subsystem.
*
- * This enforces a rate limit: not more than one kernel message
- * every printk_ratelimit_jiffies to make a denial-of-service
- * attack impossible.
+ * This enforces a rate limit: not more than 10 kernel messages
+ * every 5s to make a denial-of-service attack impossible.
*/
+DEFINE_RATELIMIT_STATE(printk_ratelimit_state, 5 * HZ, 10);
+
int printk_ratelimit(void)
{
return __ratelimit(&printk_ratelimit_state);
size_t n_subbufs = buf->chan->n_subbufs;
size_t read_subbuf;
+ if (buf->subbufs_produced == buf->subbufs_consumed &&
+ buf->offset == buf->bytes_consumed)
+ return;
+
if (buf->bytes_consumed + bytes_consumed > subbuf_size) {
relay_subbufs_consumed(buf->chan, buf->cpu, 1);
buf->bytes_consumed = 0;
relay_file_read_consume(buf, read_pos, 0);
+ consumed = buf->subbufs_consumed;
+
if (unlikely(buf->offset > subbuf_size)) {
if (produced == consumed)
return 0;
if (consumed > produced)
produced += n_subbufs * subbuf_size;
- if (consumed == produced)
+ if (consumed == produced) {
+ if (buf->offset == subbuf_size &&
+ buf->subbufs_produced > buf->subbufs_consumed)
+ return 1;
return 0;
+ }
return 1;
}
{
switch (res->flags & (IORESOURCE_SIZEALIGN | IORESOURCE_STARTALIGN)) {
case IORESOURCE_SIZEALIGN:
- return res->end - res->start + 1;
+ return resource_size(res);
case IORESOURCE_STARTALIGN:
return res->start;
default:
return -EPERM;
}
+ if (user) {
#ifdef CONFIG_RT_GROUP_SCHED
- /*
- * Do not allow realtime tasks into groups that have no runtime
- * assigned.
- */
- if (user
- && rt_policy(policy) && task_group(p)->rt_bandwidth.rt_runtime == 0)
- return -EPERM;
+ /*
+ * Do not allow realtime tasks into groups that have no runtime
+ * assigned.
+ */
+ if (rt_policy(policy) && task_group(p)->rt_bandwidth.rt_runtime == 0)
+ return -EPERM;
#endif
- retval = security_task_setscheduler(p, policy, param);
- if (retval)
- return retval;
+ retval = security_task_setscheduler(p, policy, param);
+ if (retval)
+ return retval;
+ }
+
/*
* make sure no PI-waiters arrive (or leave) while we are
* changing the priority of the task:
}
#ifdef CONFIG_SCHED_MC
-static ssize_t sched_mc_power_savings_show(struct sys_device *dev,
- struct sysdev_attribute *attr, char *page)
+static ssize_t sched_mc_power_savings_show(struct sysdev_class *class,
+ char *page)
{
return sprintf(page, "%u\n", sched_mc_power_savings);
}
-static ssize_t sched_mc_power_savings_store(struct sys_device *dev,
- struct sysdev_attribute *attr,
+static ssize_t sched_mc_power_savings_store(struct sysdev_class *class,
const char *buf, size_t count)
{
return sched_power_savings_store(buf, count, 0);
}
-static SYSDEV_ATTR(sched_mc_power_savings, 0644, sched_mc_power_savings_show,
- sched_mc_power_savings_store);
+static SYSDEV_CLASS_ATTR(sched_mc_power_savings, 0644,
+ sched_mc_power_savings_show,
+ sched_mc_power_savings_store);
#endif
#ifdef CONFIG_SCHED_SMT
-static ssize_t sched_smt_power_savings_show(struct sys_device *dev,
- struct sysdev_attribute *attr, char *page)
+static ssize_t sched_smt_power_savings_show(struct sysdev_class *dev,
+ char *page)
{
return sprintf(page, "%u\n", sched_smt_power_savings);
}
-static ssize_t sched_smt_power_savings_store(struct sys_device *dev,
- struct sysdev_attribute *attr,
+static ssize_t sched_smt_power_savings_store(struct sysdev_class *dev,
const char *buf, size_t count)
{
return sched_power_savings_store(buf, count, 1);
}
-static SYSDEV_ATTR(sched_smt_power_savings, 0644, sched_smt_power_savings_show,
+static SYSDEV_CLASS_ATTR(sched_smt_power_savings, 0644,
+ sched_smt_power_savings_show,
sched_smt_power_savings_store);
#endif
waiter.up = 0;
for (;;) {
- if (state == TASK_INTERRUPTIBLE && signal_pending(task))
- goto interrupted;
- if (state == TASK_KILLABLE && fatal_signal_pending(task))
+ if (signal_pending_state(state, task))
goto interrupted;
if (timeout <= 0)
goto timed_out;
start_workqueue_thread(cwq, -1);
} else {
cpu_maps_update_begin();
+ /*
+ * We must place this wq on list even if the code below fails.
+ * cpu_down(cpu) can remove cpu from cpu_populated_map before
+ * destroy_workqueue() takes the lock, in that case we leak
+ * cwq[cpu]->thread.
+ */
spin_lock(&workqueue_lock);
list_add(&wq->list, &workqueues);
spin_unlock(&workqueue_lock);
-
+ /*
+ * We must initialize cwqs for each possible cpu even if we
+ * are going to call destroy_workqueue() finally. Otherwise
+ * cpu_up() can hit the uninitialized cwq once we drop the
+ * lock.
+ */
for_each_possible_cpu(cpu) {
cwq = init_cpu_workqueue(wq, cpu);
if (err || !cpu_online(cpu))
menuconfig KGDB
bool "KGDB: kernel debugging with remote gdb"
- select FRAME_POINTER
depends on HAVE_ARCH_KGDB
depends on DEBUG_KERNEL && EXPERIMENTAL
help
If you say Y here, it will be possible to remotely debug the
- kernel using gdb. Documentation of kernel debugger is available
- at http://kgdb.sourceforge.net as well as in DocBook form
- in Documentation/DocBook/. If unsure, say N.
+ kernel using gdb. It is recommended but not required, that
+ you also turn on the kernel config option
+ CONFIG_FRAME_POINTER to aid in producing more reliable stack
+ backtraces in the external debugger. Documentation of
+ kernel debugger is available at http://kgdb.sourceforge.net
+ as well as in DocBook form in Documentation/DocBook/. If
+ unsure, say N.
if KGDB
}
}
EXPORT_SYMBOL(iommu_area_free);
-
-unsigned long iommu_num_pages(unsigned long addr, unsigned long len)
-{
- unsigned long size = roundup((addr & ~PAGE_MASK) + len, PAGE_SIZE);
-
- return size >> PAGE_SHIFT;
-}
-EXPORT_SYMBOL(iommu_num_pages);
return (state->s1 ^ state->s2 ^ state->s3);
}
-static void __set_random32(struct rnd_state *state, unsigned long s)
+/*
+ * Handle minimum values for seeds
+ */
+static inline u32 __seed(u32 x, u32 m)
{
- if (s == 0)
- s = 1; /* default seed is 1 */
-
-#define LCG(n) (69069 * n)
- state->s1 = LCG(s);
- state->s2 = LCG(state->s1);
- state->s3 = LCG(state->s2);
-
- /* "warm it up" */
- __random32(state);
- __random32(state);
- __random32(state);
- __random32(state);
- __random32(state);
- __random32(state);
+ return (x < m) ? x + m : x;
}
/**
*/
for_each_possible_cpu (i) {
struct rnd_state *state = &per_cpu(net_rand_state, i);
- __set_random32(state, state->s1 ^ entropy);
+ state->s1 = __seed(state->s1 ^ entropy, 1);
}
}
EXPORT_SYMBOL(srandom32);
for_each_possible_cpu(i) {
struct rnd_state *state = &per_cpu(net_rand_state,i);
- __set_random32(state, i + jiffies);
+
+#define LCG(x) ((x) * 69069) /* super-duper LCG */
+ state->s1 = __seed(LCG(i + jiffies), 1);
+ state->s2 = __seed(LCG(state->s1), 7);
+ state->s3 = __seed(LCG(state->s2), 15);
+
+ /* "warm it up" */
+ __random32(state);
+ __random32(state);
+ __random32(state);
+ __random32(state);
+ __random32(state);
+ __random32(state);
}
return 0;
}
static int __init random32_reseed(void)
{
int i;
- unsigned long seed;
for_each_possible_cpu(i) {
struct rnd_state *state = &per_cpu(net_rand_state,i);
+ u32 seeds[3];
+
+ get_random_bytes(&seeds, sizeof(seeds));
+ state->s1 = __seed(seeds[0], 1);
+ state->s2 = __seed(seeds[1], 7);
+ state->s3 = __seed(seeds[2], 15);
- get_random_bytes(&seed, sizeof(seed));
- __set_random32(state, seed);
+ /* mix it in */
+ __random32(state);
}
return 0;
}
* But that's OK - sleepers in wait_on_page_writeback() just go back to sleep.
*
* The first mb is necessary to safely close the critical section opened by the
- * TestSetPageLocked(), the second mb is necessary to enforce ordering between
- * the clear_bit and the read of the waitqueue (to avoid SMP races with a
- * parallel wait_on_page_locked()).
+ * test_and_set_bit() to lock the page; the second mb is necessary to enforce
+ * ordering between the clear_bit and the read of the waitqueue (to avoid SMP
+ * races with a parallel wait_on_page_locked()).
*/
void unlock_page(struct page *page)
{
smp_mb__before_clear_bit();
- if (!TestClearPageLocked(page))
+ if (!test_and_clear_bit(PG_locked, &page->flags))
BUG();
smp_mb__after_clear_bit();
wake_up_page(page, PG_locked);
struct page *page = find_get_page(mapping, index);
if (page) {
- if (!TestSetPageLocked(page))
+ if (trylock_page(page))
return page;
page_cache_release(page);
return NULL;
if (inode->i_blkbits == PAGE_CACHE_SHIFT ||
!mapping->a_ops->is_partially_uptodate)
goto page_not_up_to_date;
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto page_not_up_to_date;
if (!mapping->a_ops->is_partially_uptodate(page,
desc, offset))
* The !iov->iov_len check ensures we skip over unlikely
* zero-length segments (without overruning the iovec).
*/
- while (bytes || unlikely(!iov->iov_len && i->count)) {
+ while (bytes || unlikely(i->count && !iov->iov_len)) {
int copy;
copy = min(bytes, iov->iov_len - base);
static int __init hugetlb_init(void)
{
- BUILD_BUG_ON(HPAGE_SHIFT == 0);
+ /* Some platform decide whether they support huge pages at boot
+ * time. On these, such as powerpc, HPAGE_SHIFT is set to 0 when
+ * there is no such support
+ */
+ if (HPAGE_SHIFT == 0)
+ return 0;
if (!size_to_hstate(default_hstate_size)) {
default_hstate_size = HPAGE_SIZE;
* Application no longer needs these pages. If the pages are dirty,
* it's OK to just throw them away. The app will be more careful about
* data it wants to keep. Be sure to free swap resources too. The
- * zap_page_range call sets things up for refill_inactive to actually free
+ * zap_page_range call sets things up for shrink_active_list to actually free
* these pages later if no one else has touched them in the meantime,
* although we could add these pages to a global reuse list for
- * refill_inactive to pick up before reclaiming other pages.
+ * shrink_active_list to pick up before reclaiming other pages.
*
* NB: This interface discards data rather than pushes it out to swap,
* as some implementations do. This has performance implications for
mem = mem_cgroup_from_cont(cont);
old_mem = mem_cgroup_from_cont(old_cont);
- if (mem == old_mem)
- goto out;
-
/*
* Only thread group leaders are allowed to migrate, the mm_struct is
* in effect owned by the leader
return end;
}
+/**
+ * zap_vma_ptes - remove ptes mapping the vma
+ * @vma: vm_area_struct holding ptes to be zapped
+ * @address: starting address of pages to zap
+ * @size: number of bytes to zap
+ *
+ * This function only unmaps ptes assigned to VM_PFNMAP vmas.
+ *
+ * The entire address range must be fully contained within the vma.
+ *
+ * Returns 0 if successful.
+ */
+int zap_vma_ptes(struct vm_area_struct *vma, unsigned long address,
+ unsigned long size)
+{
+ if (address < vma->vm_start || address + size > vma->vm_end ||
+ !(vma->vm_flags & VM_PFNMAP))
+ return -1;
+ zap_page_range(vma, address, size, NULL);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(zap_vma_ptes);
+
/*
* Do a quick page-table lookup for a single page.
*/
* not dirty accountable.
*/
if (PageAnon(old_page)) {
- if (!TestSetPageLocked(old_page)) {
+ if (trylock_page(old_page)) {
reuse = can_share_swap_page(old_page);
unlock_page(old_page);
}
vma = find_vma(current->mm, addr);
if (!vma)
- return -1;
+ return -ENOMEM;
write = (vma->vm_flags & VM_WRITE) != 0;
BUG_ON(addr >= end);
BUG_ON(end > vma->vm_end);
len = DIV_ROUND_UP(end, PAGE_SIZE) - addr/PAGE_SIZE;
ret = get_user_pages(current, current->mm, addr,
len, write, 0, NULL, NULL);
- if (ret < 0)
+ if (ret < 0) {
+ /*
+ SUS require strange return value to mlock
+ - invalid addr generate to ENOMEM.
+ - out of memory should generate EAGAIN.
+ */
+ if (ret == -EFAULT)
+ ret = -ENOMEM;
+ else if (ret == -ENOMEM)
+ ret = -EAGAIN;
return ret;
- return ret == len ? 0 : -1;
+ }
+ return ret == len ? 0 : -ENOMEM;
}
#if !defined(__HAVE_ARCH_GATE_AREA)
* establishing additional references. We are the only one
* holding a reference to the new page at this point.
*/
- if (TestSetPageLocked(newpage))
+ if (!trylock_page(newpage))
BUG();
/* Prepare mapping for the new page.*/
BUG_ON(charge);
rc = -EAGAIN;
- if (TestSetPageLocked(page)) {
+ if (!trylock_page(page)) {
if (!force)
goto move_newpage;
lock_page(page);
mm->locked_vm -= pages;
out:
- if (ret == -ENOMEM)
- ret = -EAGAIN;
return ret;
}
#ifdef CONFIG_DEBUG_MEMORY_INIT
int __meminitdata mminit_loglevel;
+#ifndef SECTIONS_SHIFT
+#define SECTIONS_SHIFT 0
+#endif
+
/* The zonelists are simply reported, validation is manual. */
void mminit_verify_zonelist(void)
{
NR_PAGEFLAGS);
mminit_dprintk(MMINIT_TRACE, "pageflags_layout_shifts",
"Section %d Node %d Zone %d\n",
-#ifdef SECTIONS_SHIFT
SECTIONS_SHIFT,
-#else
- 0,
-#endif
NODES_SHIFT,
ZONES_SHIFT);
mminit_dprintk(MMINIT_TRACE, "pageflags_layout_offsets",
if (vma_tmp->vm_end > addr) {
vma = vma_tmp;
if (vma_tmp->vm_start <= addr)
- return vma;
+ break;
__rb_link = &__rb_parent->rb_left;
} else {
rb_prev = __rb_parent;
}
EXPORT_SYMBOL(vmalloc_node);
+#ifndef PAGE_KERNEL_EXEC
+# define PAGE_KERNEL_EXEC PAGE_KERNEL
+#endif
+
+/**
+ * vmalloc_exec - allocate virtually contiguous, executable memory
+ * @size: allocation size
+ *
+ * Kernel-internal function to allocate enough pages to cover @size
+ * the page level allocator and map them into contiguous and
+ * executable kernel virtual space.
+ *
+ * For tight control over page level allocator and protection flags
+ * use __vmalloc() instead.
+ */
+
+void *vmalloc_exec(unsigned long size)
+{
+ return __vmalloc(size, GFP_KERNEL | __GFP_HIGHMEM, PAGE_KERNEL_EXEC);
+}
+
/**
* vmalloc_32 - allocate virtually contiguous memory (32bit addressable)
* @size: allocation size
return find_min_pfn_for_node(MAX_NUMNODES);
}
-/**
- * find_max_pfn_with_active_regions - Find the maximum PFN registered
- *
- * It returns the maximum PFN based on information provided via
- * add_active_range().
- */
-unsigned long __init find_max_pfn_with_active_regions(void)
-{
- int i;
- unsigned long max_pfn = 0;
-
- for (i = 0; i < nr_nodemap_entries; i++)
- max_pfn = max(max_pfn, early_node_map[i].end_pfn);
-
- return max_pfn;
-}
-
/*
* early_calculate_totalpages()
* Sum pages in active regions for movable zone.
referenced += page_referenced_anon(page, mem_cont);
else if (is_locked)
referenced += page_referenced_file(page, mem_cont);
- else if (TestSetPageLocked(page))
+ else if (!trylock_page(page))
referenced++;
else {
if (page->mapping)
* Leaving it set also helps swapoff to reinstate ptes
* faster for those pages still in swapcache.
*/
- if (page_test_dirty(page)) {
+ if ((!PageAnon(page) || PageSwapCache(page)) &&
+ page_test_dirty(page)) {
page_clear_dirty(page);
set_page_dirty(page);
}
}
/* We have to do this with page locked to prevent races */
- if (TestSetPageLocked(swappage)) {
+ if (!trylock_page(swappage)) {
shmem_swp_unmap(entry);
spin_unlock(&info->lock);
wait_on_page_locked(swappage);
shmem_swp_unmap(entry);
filepage = find_get_page(mapping, idx);
if (filepage &&
- (!PageUptodate(filepage) || TestSetPageLocked(filepage))) {
+ (!PageUptodate(filepage) || !trylock_page(filepage))) {
spin_unlock(&info->lock);
wait_on_page_locked(filepage);
page_cache_release(filepage);
* Avoid taking zone->lru_lock if possible, but if it is taken, retain it
* for the remainder of the operation.
*
- * The locking in this function is against shrink_cache(): we recheck the
- * page count inside the lock to see whether shrink_cache grabbed the page
- * via the LRU. If it did, give up: shrink_cache will free it.
+ * The locking in this function is against shrink_inactive_list(): we recheck
+ * the page count inside the lock to see whether shrink_inactive_list()
+ * grabbed the page via the LRU. If it did, give up: shrink_inactive_list()
+ * will free it.
*/
void release_pages(struct page **pages, int nr, int cold)
{
for (i = 0; i < pagevec_count(pvec); i++) {
struct page *page = pvec->pages[i];
- if (PagePrivate(page) && !TestSetPageLocked(page)) {
+ if (PagePrivate(page) && trylock_page(page)) {
if (PagePrivate(page))
try_to_release_page(page, 0);
unlock_page(page);
*/
static inline void free_swap_cache(struct page *page)
{
- if (PageSwapCache(page) && !TestSetPageLocked(page)) {
+ if (PageSwapCache(page) && trylock_page(page)) {
remove_exclusive_swap_page(page);
unlock_page(page);
}
* re-using the just freed swap entry for an existing page.
* May fail (-ENOMEM) if radix-tree node allocation failed.
*/
- SetPageLocked(new_page);
+ set_page_locked(new_page);
err = add_to_swap_cache(new_page, entry, gfp_mask & GFP_KERNEL);
- if (!err) {
+ if (likely(!err)) {
/*
* Initiate read into locked page and return.
*/
swap_readpage(NULL, new_page);
return new_page;
}
- ClearPageLocked(new_page);
+ clear_page_locked(new_page);
swap_free(entry);
} while (err != -ENOMEM);
if (p) {
if (swap_entry_free(p, swp_offset(entry)) == 1) {
page = find_get_page(&swapper_space, entry.val);
- if (page && unlikely(TestSetPageLocked(page))) {
+ if (page && unlikely(!trylock_page(page))) {
page_cache_release(page);
page = NULL;
}
if (!down_read_trylock(&mm->mmap_sem)) {
/*
- * Activate page so shrink_cache is unlikely to unmap its
- * ptes while lock is dropped, so swapoff can make progress.
+ * Activate page so shrink_inactive_list is unlikely to unmap
+ * its ptes while lock is dropped, so swapoff can make progress.
*/
activate_page(page);
unlock_page(page);
cancel_dirty_page(page, PAGE_CACHE_SIZE);
remove_from_page_cache(page);
- ClearPageUptodate(page);
ClearPageMappedToDisk(page);
page_cache_release(page); /* pagecache ref */
}
if (page_index > next)
next = page_index;
next++;
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
continue;
if (PageWriteback(page)) {
unlock_page(page);
pgoff_t index;
int lock_failed;
- lock_failed = TestSetPageLocked(page);
+ lock_failed = !trylock_page(page);
/*
* We really shouldn't be looking at the ->index of an
BUG_ON(PagePrivate(page));
__remove_from_page_cache(page);
spin_unlock_irq(&mapping->tree_lock);
- ClearPageUptodate(page);
page_cache_release(page); /* pagecache ref */
return 1;
failed:
page = lru_to_page(page_list);
list_del(&page->lru);
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto keep;
VM_BUG_ON(PageActive(page));
* A synchronous write - probably a ramdisk. Go
* ahead and try to reclaim the page.
*/
- if (TestSetPageLocked(page))
+ if (!trylock_page(page))
goto keep;
if (PageDirty(page) || PageWriteback(page))
goto keep_locked;
if (sc->nr_scanned && priority < DEF_PRIORITY - 2)
congestion_wait(WRITE, HZ/10);
}
- /* top priority shrink_caches still had more to do? don't OOM, then */
+ /* top priority shrink_zones still had more to do? don't OOM, then */
if (!sc->all_unreclaimable && scan_global_lru(sc))
ret = nr_reclaimed;
out:
int zone_reclaim_mode __read_mostly;
#define RECLAIM_OFF 0
-#define RECLAIM_ZONE (1<<0) /* Run shrink_cache on the zone */
+#define RECLAIM_ZONE (1<<0) /* Run shrink_inactive_list on the zone */
#define RECLAIM_WRITE (1<<1) /* Writeout pages during reclaim */
#define RECLAIM_SWAP (1<<2) /* Swap pages out during reclaim */
# Network configuration
#
-menu "Networking"
-
-config NET
+menuconfig NET
bool "Networking support"
---help---
Unless you really know what you are doing, you should say Y here.
recommended to read the NET-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-# Make sure that all config symbols are dependent on NET
if NET
menu "Networking options"
source "net/9p/Kconfig"
endif # if NET
-endmenu # Networking
-
static void set_mpc_ctrl_addr_rcvd(struct k_message *mesg, struct mpoa_client *mpc);
static void set_mps_mac_addr_rcvd(struct k_message *mesg, struct mpoa_client *mpc);
-static uint8_t *copy_macs(struct mpoa_client *mpc, uint8_t *router_mac,
- uint8_t *tlvs, uint8_t mps_macs, uint8_t device_type);
+static const uint8_t *copy_macs(struct mpoa_client *mpc,
+ const uint8_t *router_mac,
+ const uint8_t *tlvs, uint8_t mps_macs,
+ uint8_t device_type);
static void purge_egress_shortcut(struct atm_vcc *vcc, eg_cache_entry *entry);
-static void send_set_mps_ctrl_addr(char *addr, struct mpoa_client *mpc);
+static void send_set_mps_ctrl_addr(const char *addr, struct mpoa_client *mpc);
static void mpoad_close(struct atm_vcc *vcc);
static int msg_from_mpoad(struct atm_vcc *vcc, struct sk_buff *skb);
* lec sees a TLV it uses the pointer to call this function.
*
*/
-static void lane2_assoc_ind(struct net_device *dev, uint8_t *mac_addr,
- uint8_t *tlvs, uint32_t sizeoftlvs)
+static void lane2_assoc_ind(struct net_device *dev, const u8 *mac_addr,
+ const u8 *tlvs, u32 sizeoftlvs)
{
uint32_t type;
uint8_t length, mpoa_device_type, number_of_mps_macs;
- uint8_t *end_of_tlvs;
+ const uint8_t *end_of_tlvs;
struct mpoa_client *mpc;
mpoa_device_type = number_of_mps_macs = 0; /* silence gcc */
* plus the possible MAC address(es) to mpc->mps_macs.
* For a freshly allocated MPOA client mpc->mps_macs == 0.
*/
-static uint8_t *copy_macs(struct mpoa_client *mpc, uint8_t *router_mac,
- uint8_t *tlvs, uint8_t mps_macs, uint8_t device_type)
+static const uint8_t *copy_macs(struct mpoa_client *mpc,
+ const uint8_t *router_mac,
+ const uint8_t *tlvs, uint8_t mps_macs,
+ uint8_t device_type)
{
int num_macs;
num_macs = (mps_macs > 1) ? mps_macs : 1;
return arg;
}
-static void send_set_mps_ctrl_addr(char *addr, struct mpoa_client *mpc)
+static void send_set_mps_ctrl_addr(const char *addr, struct mpoa_client *mpc)
{
struct k_message mesg;
{ .procname = "ax25", .ctl_name = NET_AX25, },
{ }
};
+
static const ctl_table ax25_param_table[] = {
{
.ctl_name = NET_AX25_IP_DEFAULT_MODE,
.extra1 = &min_proto,
.extra2 = &max_proto
},
+#ifdef CONFIG_AX25_DAMA_SLAVE
{
.ctl_name = NET_AX25_DAMA_SLAVE_TIMEOUT,
.procname = "dama_slave_timeout",
.extra1 = &min_ds_timeout,
.extra2 = &max_ds_timeout
},
+#endif
+
{ .ctl_name = 0 } /* that's all, folks! */
};
ax25_table[n].procname = ax25_dev->dev->name;
ax25_table[n].mode = 0555;
-#ifndef CONFIG_AX25_DAMA_SLAVE
- /*
- * We do not wish to have a representation of this parameter
- * in /proc/sys/ when configured *not* to include the
- * AX.25 DAMA slave code, do we?
- */
-
- child[AX25_VALUES_DS_TIMEOUT].procname = NULL;
-#endif
-
child[AX25_MAX_VALUES].ctl_name = 0; /* just in case... */
for (k = 0; k < AX25_MAX_VALUES; k++)
#define BT_DBG(D...)
#endif
-#define VERSION "1.2"
+#define VERSION "1.3"
+
+static int compress_src = 1;
+static int compress_dst = 1;
static LIST_HEAD(bnep_session_list);
static DECLARE_RWSEM(bnep_session_sem);
iv[il++] = (struct kvec) { &type, 1 };
len++;
- if (!compare_ether_addr(eh->h_dest, s->eh.h_source))
+ if (compress_src && !compare_ether_addr(eh->h_dest, s->eh.h_source))
type |= 0x01;
- if (!compare_ether_addr(eh->h_source, s->eh.h_dest))
+ if (compress_dst && !compare_ether_addr(eh->h_source, s->eh.h_dest))
type |= 0x02;
if (type)
module_init(bnep_init);
module_exit(bnep_exit);
+module_param(compress_src, bool, 0644);
+MODULE_PARM_DESC(compress_src, "Compress sources headers");
+
+module_param(compress_dst, bool, 0644);
+MODULE_PARM_DESC(compress_dst, "Compress destination headers");
+
MODULE_AUTHOR("David Libault <david.libault@inventel.fr>, Maxim Krasnyansky <maxk@qualcomm.com>");
MODULE_DESCRIPTION("Bluetooth BNEP ver " VERSION);
MODULE_VERSION(VERSION);
static int br_change_mtu(struct net_device *dev, int new_mtu)
{
- if (new_mtu < 68 || new_mtu > br_min_mtu(netdev_priv(dev)))
+ struct net_bridge *br = netdev_priv(dev);
+ if (new_mtu < 68 || new_mtu > br_min_mtu(br))
return -EINVAL;
dev->mtu = new_mtu;
+
+#ifdef CONFIG_BRIDGE_NETFILTER
+ /* remember the MTU in the rtable for PMTU */
+ br->fake_rtable.u.dst.metrics[RTAX_MTU - 1] = new_mtu;
+#endif
+
return 0;
}
br->topology_change = 0;
br->topology_change_detected = 0;
br->ageing_time = 300 * HZ;
+
+ br_netfilter_rtable_init(br);
+
INIT_LIST_HEAD(&br->age_list);
br_stp_timer_init(br);
pppoe_proto(skb) == htons(PPP_IPV6) && \
brnf_filter_pppoe_tagged)
-/* We need these fake structures to make netfilter happy --
- * lots of places assume that skb->dst != NULL, which isn't
- * all that unreasonable.
- *
+/*
+ * Initialize bogus route table used to keep netfilter happy.
* Currently, we fill in the PMTU entry because netfilter
* refragmentation needs it, and the rt_flags entry because
* ipt_REJECT needs it. Future netfilter modules might
- * require us to fill additional fields. */
-static struct net_device __fake_net_device = {
- .hard_header_len = ETH_HLEN,
-#ifdef CONFIG_NET_NS
- .nd_net = &init_net,
-#endif
-};
+ * require us to fill additional fields.
+ */
+void br_netfilter_rtable_init(struct net_bridge *br)
+{
+ struct rtable *rt = &br->fake_rtable;
-static struct rtable __fake_rtable = {
- .u = {
- .dst = {
- .__refcnt = ATOMIC_INIT(1),
- .dev = &__fake_net_device,
- .path = &__fake_rtable.u.dst,
- .metrics = {[RTAX_MTU - 1] = 1500},
- .flags = DST_NOXFRM,
- }
- },
- .rt_flags = 0,
-};
+ atomic_set(&rt->u.dst.__refcnt, 1);
+ rt->u.dst.dev = br->dev;
+ rt->u.dst.path = &rt->u.dst;
+ rt->u.dst.metrics[RTAX_MTU - 1] = 1500;
+ rt->u.dst.flags = DST_NOXFRM;
+}
+
+static inline struct rtable *bridge_parent_rtable(const struct net_device *dev)
+{
+ struct net_bridge_port *port = rcu_dereference(dev->br_port);
+
+ return port ? &port->br->fake_rtable : NULL;
+}
static inline struct net_device *bridge_parent(const struct net_device *dev)
{
}
nf_bridge->mask ^= BRNF_NF_BRIDGE_PREROUTING;
- skb->rtable = &__fake_rtable;
- dst_hold(&__fake_rtable.u.dst);
+ skb->rtable = bridge_parent_rtable(nf_bridge->physindev);
+ if (!skb->rtable) {
+ kfree_skb(skb);
+ return 0;
+ }
+ dst_hold(&skb->rtable->u.dst);
skb->dev = nf_bridge->physindev;
nf_bridge_push_encap_header(skb);
skb->pkt_type = PACKET_HOST;
}
} else {
- skb->rtable = &__fake_rtable;
- dst_hold(&__fake_rtable.u.dst);
+ skb->rtable = bridge_parent_rtable(nf_bridge->physindev);
+ if (!skb->rtable) {
+ kfree_skb(skb);
+ return 0;
+ }
+ dst_hold(&skb->rtable->u.dst);
}
skb->dev = nf_bridge->physindev;
const struct net_device *out,
int (*okfn)(struct sk_buff *))
{
- if (skb->rtable == &__fake_rtable) {
- dst_release(&__fake_rtable.u.dst);
+ if (skb->rtable && skb->rtable == bridge_parent_rtable(in)) {
+ dst_release(&skb->rtable->u.dst);
skb->rtable = NULL;
}
#include <linux/netdevice.h>
#include <linux/if_bridge.h>
+#include <net/route.h>
#define BR_HASH_BITS 8
#define BR_HASH_SIZE (1 << BR_HASH_BITS)
struct hlist_head hash[BR_HASH_SIZE];
struct list_head age_list;
unsigned long feature_mask;
+#ifdef CONFIG_BRIDGE_NETFILTER
+ struct rtable fake_rtable;
+#endif
unsigned long flags;
#define BR_SET_MAC_ADDR 0x00000001
#ifdef CONFIG_BRIDGE_NETFILTER
extern int br_netfilter_init(void);
extern void br_netfilter_fini(void);
+extern void br_netfilter_rtable_init(struct net_bridge *);
#else
#define br_netfilter_init() (0)
#define br_netfilter_fini() do { } while(0)
+#define br_netfilter_rtable_init(x)
#endif
/* br_stp.c */
/* called under bridge lock */
static void br_make_forwarding(struct net_bridge_port *p)
{
- if (p->state == BR_STATE_BLOCKING) {
- if (p->br->stp_enabled == BR_KERNEL_STP)
- p->state = BR_STATE_LISTENING;
- else
- p->state = BR_STATE_LEARNING;
+ struct net_bridge *br = p->br;
- br_log_state(p);
- mod_timer(&p->forward_delay_timer, jiffies + p->br->forward_delay); }
+ if (p->state != BR_STATE_BLOCKING)
+ return;
+
+ if (br->forward_delay == 0) {
+ p->state = BR_STATE_FORWARDING;
+ br_topology_change_detection(br);
+ del_timer(&p->forward_delay_timer);
+ }
+ else if (p->br->stp_enabled == BR_KERNEL_STP)
+ p->state = BR_STATE_LISTENING;
+ else
+ p->state = BR_STATE_LEARNING;
+
+ br_log_state(p);
+
+ if (br->forward_delay != 0)
+ mod_timer(&p->forward_delay_timer, jiffies + br->forward_delay);
}
/* called under bridge lock */
skb->tc_verd = SET_TC_AT(skb->tc_verd,AT_EGRESS);
#endif
if (q->enqueue) {
- spinlock_t *root_lock = qdisc_root_lock(q);
+ spinlock_t *root_lock = qdisc_lock(q);
spin_lock(root_lock);
spin_unlock(root_lock);
- rc = rc == NET_XMIT_BYPASS ? NET_XMIT_SUCCESS : rc;
goto out;
}
if (queue->input_pkt_queue.qlen <= netdev_max_backlog) {
if (queue->input_pkt_queue.qlen) {
enqueue:
- dev_hold(skb->dev);
__skb_queue_tail(&queue->input_pkt_queue, skb);
local_irq_restore(flags);
return NET_RX_SUCCESS;
EXPORT_SYMBOL(netif_rx_ni);
-static inline struct net_device *skb_bond(struct sk_buff *skb)
-{
- struct net_device *dev = skb->dev;
-
- if (dev->master) {
- if (skb_bond_should_drop(skb)) {
- kfree_skb(skb);
- return NULL;
- }
- skb->dev = dev->master;
- }
-
- return dev;
-}
-
-
static void net_tx_action(struct softirq_action *h)
{
struct softnet_data *sd = &__get_cpu_var(softnet_data);
smp_mb__before_clear_bit();
clear_bit(__QDISC_STATE_SCHED, &q->state);
- root_lock = qdisc_root_lock(q);
+ root_lock = qdisc_lock(q);
if (spin_trylock(root_lock)) {
qdisc_run(q);
spin_unlock(root_lock);
rxq = &dev->rx_queue;
q = rxq->qdisc;
- if (q) {
+ if (q != &noop_qdisc) {
spin_lock(qdisc_lock(q));
result = qdisc_enqueue_root(skb, q);
spin_unlock(qdisc_lock(q));
struct packet_type **pt_prev,
int *ret, struct net_device *orig_dev)
{
- if (!skb->dev->rx_queue.qdisc)
+ if (skb->dev->rx_queue.qdisc == &noop_qdisc)
goto out;
if (*pt_prev) {
{
struct packet_type *ptype, *pt_prev;
struct net_device *orig_dev;
+ struct net_device *null_or_orig;
int ret = NET_RX_DROP;
__be16 type;
if (!skb->iif)
skb->iif = skb->dev->ifindex;
- orig_dev = skb_bond(skb);
-
- if (!orig_dev)
- return NET_RX_DROP;
+ null_or_orig = NULL;
+ orig_dev = skb->dev;
+ if (orig_dev->master) {
+ if (skb_bond_should_drop(skb))
+ null_or_orig = orig_dev; /* deliver only exact match */
+ else
+ skb->dev = orig_dev->master;
+ }
__get_cpu_var(netdev_rx_stat).total++;
#endif
list_for_each_entry_rcu(ptype, &ptype_all, list) {
- if (!ptype->dev || ptype->dev == skb->dev) {
+ if (ptype->dev == null_or_orig || ptype->dev == skb->dev ||
+ ptype->dev == orig_dev) {
if (pt_prev)
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = ptype;
list_for_each_entry_rcu(ptype,
&ptype_base[ntohs(type) & PTYPE_HASH_MASK], list) {
if (ptype->type == type &&
- (!ptype->dev || ptype->dev == skb->dev)) {
+ (ptype->dev == null_or_orig || ptype->dev == skb->dev ||
+ ptype->dev == orig_dev)) {
if (pt_prev)
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = ptype;
return ret;
}
+/* Network device is going away, flush any packets still pending */
+static void flush_backlog(void *arg)
+{
+ struct net_device *dev = arg;
+ struct softnet_data *queue = &__get_cpu_var(softnet_data);
+ struct sk_buff *skb, *tmp;
+
+ skb_queue_walk_safe(&queue->input_pkt_queue, skb, tmp)
+ if (skb->dev == dev) {
+ __skb_unlink(skb, &queue->input_pkt_queue);
+ kfree_skb(skb);
+ }
+}
+
static int process_backlog(struct napi_struct *napi, int quota)
{
int work = 0;
napi->weight = weight_p;
do {
struct sk_buff *skb;
- struct net_device *dev;
local_irq_disable();
skb = __skb_dequeue(&queue->input_pkt_queue);
local_irq_enable();
break;
}
-
local_irq_enable();
- dev = skb->dev;
-
netif_receive_skb(skb);
-
- dev_put(dev);
} while (++work < quota && jiffies == start_time);
return work;
}
}
+ /* Enable software GSO if SG is supported. */
+ if (dev->features & NETIF_F_SG)
+ dev->features |= NETIF_F_GSO;
+
netdev_initialize_kobject(dev);
ret = netdev_register_kobject(dev);
if (ret)
dev->reg_state = NETREG_UNREGISTERED;
+ on_each_cpu(flush_backlog, dev, 1);
+
netdev_wait_allrefs(dev);
/* paranoia */
{
netdev_init_one_queue(dev, &dev->rx_queue, NULL);
netdev_for_each_tx_queue(dev, netdev_init_one_queue, NULL);
+ spin_lock_init(&dev->tx_global_lock);
}
/**
struct neighbour *n = neigh_get_first(seq);
if (n) {
+ --(*pos);
while (*pos) {
n = neigh_get_next(seq, n, pos);
if (!n)
struct pneigh_entry *pn = pneigh_get_first(seq);
if (pn) {
+ --(*pos);
while (*pos) {
pn = pneigh_get_next(seq, pn, pos);
if (!pn)
{
struct neigh_seq_state *state = seq->private;
void *rc;
+ loff_t idxpos = *pos;
- rc = neigh_get_idx(seq, pos);
+ rc = neigh_get_idx(seq, &idxpos);
if (!rc && !(state->flags & NEIGH_SEQ_NEIGH_ONLY))
- rc = pneigh_get_idx(seq, pos);
+ rc = pneigh_get_idx(seq, &idxpos);
return rc;
}
__acquires(tbl->lock)
{
struct neigh_seq_state *state = seq->private;
- loff_t pos_minus_one;
state->tbl = tbl;
state->bucket = 0;
read_lock_bh(&tbl->lock);
- pos_minus_one = *pos - 1;
- return *pos ? neigh_get_idx_any(seq, &pos_minus_one) : SEQ_START_TOKEN;
+ return *pos ? neigh_get_idx_any(seq, pos) : SEQ_START_TOKEN;
}
EXPORT_SYMBOL(neigh_seq_start);
void *rc;
if (v == SEQ_START_TOKEN) {
- rc = neigh_get_idx(seq, pos);
+ rc = neigh_get_first(seq);
goto out;
}
local_irq_save(flags);
__netif_tx_lock(txq, smp_processor_id());
if (netif_tx_queue_stopped(txq) ||
+ netif_tx_queue_frozen(txq) ||
dev->hard_start_xmit(skb, dev) != NETDEV_TX_OK) {
skb_queue_head(&npinfo->txq, skb);
__netif_tx_unlock(txq);
#include <asm/div64.h> /* do_div */
#include <asm/timex.h>
-#define VERSION "pktgen v2.69: Packet Generator for packet performance testing.\n"
+#define VERSION "pktgen v2.70: Packet Generator for packet performance testing.\n"
#define IP_NAME_SZ 32
#define MAX_MPLS_LABELS 16 /* This is the max label stack depth */
#define F_FLOW_SEQ (1<<11) /* Sequential flows */
#define F_IPSEC_ON (1<<12) /* ipsec on for flows */
#define F_QUEUE_MAP_RND (1<<13) /* queue map Random */
+#define F_QUEUE_MAP_CPU (1<<14) /* queue map mirrors smp_processor_id() */
/* Thread control flag bits */
#define T_TERMINATE (1<<0)
if (pkt_dev->flags & F_QUEUE_MAP_RND)
seq_printf(seq, "QUEUE_MAP_RND ");
+ if (pkt_dev->flags & F_QUEUE_MAP_CPU)
+ seq_printf(seq, "QUEUE_MAP_CPU ");
+
if (pkt_dev->cflows) {
if (pkt_dev->flags & F_FLOW_SEQ)
seq_printf(seq, "FLOW_SEQ "); /*in sequence flows*/
else if (strcmp(f, "!QUEUE_MAP_RND") == 0)
pkt_dev->flags &= ~F_QUEUE_MAP_RND;
+
+ else if (strcmp(f, "QUEUE_MAP_CPU") == 0)
+ pkt_dev->flags |= F_QUEUE_MAP_CPU;
+
+ else if (strcmp(f, "!QUEUE_MAP_CPU") == 0)
+ pkt_dev->flags &= ~F_QUEUE_MAP_CPU;
#ifdef CONFIG_XFRM
else if (strcmp(f, "IPSEC") == 0)
pkt_dev->flags |= F_IPSEC_ON;
return NOTIFY_DONE;
}
+static struct net_device *pktgen_dev_get_by_name(struct pktgen_dev *pkt_dev, const char *ifname)
+{
+ char b[IFNAMSIZ+5];
+ int i = 0;
+
+ for(i=0; ifname[i] != '@'; i++) {
+ if(i == IFNAMSIZ)
+ break;
+
+ b[i] = ifname[i];
+ }
+ b[i] = 0;
+
+ return dev_get_by_name(&init_net, b);
+}
+
+
/* Associate pktgen_dev with a device. */
static int pktgen_setup_dev(struct pktgen_dev *pkt_dev, const char *ifname)
pkt_dev->odev = NULL;
}
- odev = dev_get_by_name(&init_net, ifname);
+ odev = pktgen_dev_get_by_name(pkt_dev, ifname);
if (!odev) {
printk(KERN_ERR "pktgen: no such netdevice: \"%s\"\n", ifname);
return -ENODEV;
if (pkt_dev->flows[flow].count >= pkt_dev->lflow) {
/* reset time */
pkt_dev->flows[flow].count = 0;
+ pkt_dev->flows[flow].flags = 0;
pkt_dev->curfl += 1;
if (pkt_dev->curfl >= pkt_dev->cflows)
pkt_dev->curfl = 0; /*reset */
}
} else {
flow = random32() % pkt_dev->cflows;
+ pkt_dev->curfl = flow;
- if (pkt_dev->flows[flow].count > pkt_dev->lflow)
+ if (pkt_dev->flows[flow].count > pkt_dev->lflow) {
pkt_dev->flows[flow].count = 0;
+ pkt_dev->flows[flow].flags = 0;
+ }
}
return pkt_dev->curfl;
#endif
static void set_cur_queue_map(struct pktgen_dev *pkt_dev)
{
- if (pkt_dev->queue_map_min < pkt_dev->queue_map_max) {
+
+ if (pkt_dev->flags & F_QUEUE_MAP_CPU)
+ pkt_dev->cur_queue_map = smp_processor_id();
+
+ else if (pkt_dev->queue_map_min < pkt_dev->queue_map_max) {
__u16 t;
if (pkt_dev->flags & F_QUEUE_MAP_RND) {
t = random32() %
mc = random32() % pkt_dev->src_mac_count;
else {
mc = pkt_dev->cur_src_mac_offset++;
- if (pkt_dev->cur_src_mac_offset >
+ if (pkt_dev->cur_src_mac_offset >=
pkt_dev->src_mac_count)
pkt_dev->cur_src_mac_offset = 0;
}
else {
mc = pkt_dev->cur_dst_mac_offset++;
- if (pkt_dev->cur_dst_mac_offset >
+ if (pkt_dev->cur_dst_mac_offset >=
pkt_dev->dst_mac_count) {
pkt_dev->cur_dst_mac_offset = 0;
}
txq = netdev_get_tx_queue(odev, queue_map);
if (netif_tx_queue_stopped(txq) ||
+ netif_tx_queue_frozen(txq) ||
need_resched()) {
idle_start = getCurUs();
pkt_dev->idle_acc += getCurUs() - idle_start;
- if (netif_tx_queue_stopped(txq)) {
+ if (netif_tx_queue_stopped(txq) ||
+ netif_tx_queue_frozen(txq)) {
pkt_dev->next_tx_us = getCurUs(); /* TODO */
pkt_dev->next_tx_ns = 0;
goto out; /* Try the next interface */
txq = netdev_get_tx_queue(odev, queue_map);
__netif_tx_lock_bh(txq);
- if (!netif_tx_queue_stopped(txq)) {
+ if (!netif_tx_queue_stopped(txq) &&
+ !netif_tx_queue_frozen(txq)) {
atomic_inc(&(pkt_dev->skb->users));
retry_now:
C(head);
C(data);
C(truesize);
+#if defined(CONFIG_MAC80211) || defined(CONFIG_MAC80211_MODULE)
+ C(do_not_encrypt);
+#endif
atomic_set(&n->users, 1);
atomic_inc(&(skb_shinfo(skb)->dataref));
extern int dccp_retransmit_skb(struct sock *sk);
extern void dccp_send_ack(struct sock *sk);
-extern void dccp_reqsk_send_ack(struct sk_buff *sk, struct request_sock *rsk);
+extern void dccp_reqsk_send_ack(struct sock *sk, struct sk_buff *skb,
+ struct request_sock *rsk);
extern void dccp_send_sync(struct sock *sk, const u64 seq,
const enum dccp_pkt_type pkt_type);
EXPORT_SYMBOL_GPL(dccp_child_process);
-void dccp_reqsk_send_ack(struct sk_buff *skb, struct request_sock *rsk)
+void dccp_reqsk_send_ack(struct sock *sk, struct sk_buff *skb,
+ struct request_sock *rsk)
{
DCCP_BUG("DCCP-ACK packets are never sent in LISTEN/RESPOND state");
}
crypto_aead_ivsize(aead);
if (x->props.mode == XFRM_MODE_TUNNEL)
x->props.header_len += sizeof(struct iphdr);
- else if (x->props.mode == XFRM_MODE_BEET)
+ else if (x->props.mode == XFRM_MODE_BEET && x->sel.family != AF_INET6)
x->props.header_len += IPV4_BEET_PHMAXLEN;
if (x->encap) {
struct xfrm_encap_tmpl *encap = x->encap;
#define HBUFFERLEN 30
char hbuffer[HBUFFERLEN];
int j,k;
- const char hexbuf[]= "0123456789abcdef";
for (k=0, j=0; k < HBUFFERLEN-3 && j < ETH_ALEN; j++) {
- hbuffer[k++]=hexbuf[(payload->src_hw[j]>>4)&15];
- hbuffer[k++]=hexbuf[payload->src_hw[j]&15];
+ hbuffer[k++] = hex_asc_hi(payload->src_hw[j]);
+ hbuffer[k++] = hex_asc_lo(payload->src_hw[j]);
hbuffer[k++]=':';
}
hbuffer[--k]='\0';
spin_lock_bh(&recent_lock);
list_del(&t->list);
spin_unlock_bh(&recent_lock);
- recent_table_flush(t);
#ifdef CONFIG_PROC_FS
remove_proc_entry(t->name, proc_dir);
#endif
+ recent_table_flush(t);
kfree(t);
}
mutex_unlock(&recent_mutex);
SNMP_MIB_ITEM("TCPDSACKIgnoredOld", LINUX_MIB_TCPDSACKIGNOREDOLD),
SNMP_MIB_ITEM("TCPDSACKIgnoredNoUndo", LINUX_MIB_TCPDSACKIGNOREDNOUNDO),
SNMP_MIB_ITEM("TCPSpuriousRTOs", LINUX_MIB_TCPSPURIOUSRTOS),
+ SNMP_MIB_ITEM("TCPMD5NotFound", LINUX_MIB_TCPMD5NOTFOUND),
+ SNMP_MIB_ITEM("TCPMD5Unexpected", LINUX_MIB_TCPMD5UNEXPECTED),
SNMP_MIB_SENTINEL
};
/* BSD 4.2 compatibility hack :-( */
if (mtu == 0 &&
- old_mtu >= dst_metric(&rth->u.dst, RTAX_MTU) &&
+ old_mtu >= dst_mtu(&rth->u.dst) &&
old_mtu >= 68 + (iph->ihl << 2))
old_mtu -= iph->ihl << 2;
mtu = guess_mtu(old_mtu);
}
- if (mtu <= dst_metric(&rth->u.dst, RTAX_MTU)) {
- if (mtu < dst_metric(&rth->u.dst, RTAX_MTU)) {
+ if (mtu <= dst_mtu(&rth->u.dst)) {
+ if (mtu < dst_mtu(&rth->u.dst)) {
dst_confirm(&rth->u.dst);
if (mtu < ip_rt_min_pmtu) {
mtu = ip_rt_min_pmtu;
static void ip_rt_update_pmtu(struct dst_entry *dst, u32 mtu)
{
- if (dst_metric(dst, RTAX_MTU) > mtu && mtu >= 68 &&
+ if (dst_mtu(dst) > mtu && mtu >= 68 &&
!(dst_metric_locked(dst, RTAX_MTU))) {
if (mtu < ip_rt_min_pmtu) {
mtu = ip_rt_min_pmtu;
if (dst_metric(&rt->u.dst, RTAX_HOPLIMIT) == 0)
rt->u.dst.metrics[RTAX_HOPLIMIT-1] = sysctl_ip_default_ttl;
- if (dst_metric(&rt->u.dst, RTAX_MTU) > IP_MAX_MTU)
+ if (dst_mtu(&rt->u.dst) > IP_MAX_MTU)
rt->u.dst.metrics[RTAX_MTU-1] = IP_MAX_MTU;
if (dst_metric(&rt->u.dst, RTAX_ADVMSS) == 0)
rt->u.dst.metrics[RTAX_ADVMSS-1] = max_t(unsigned int, rt->u.dst.dev->mtu - 40,
return rc;
}
+#ifdef CONFIG_SYSCTL
/*
* We really need to sanitize the damn ipv4 init order, then all
* this nonsense will go away.
{
register_sysctl_paths(ipv4_route_path, ipv4_route_table);
}
+#endif
EXPORT_SYMBOL(__ip_select_ident);
EXPORT_SYMBOL(ip_route_input);
.mode = 0644,
.proc_handler = &ipv4_doint_and_flush,
.strategy = &ipv4_doint_and_flush_strategy,
+ .extra2 = &init_net,
},
{
.ctl_name = NET_IPV4_NO_PMTU_DISC,
rep.th.doff = arg.iov[0].iov_len/4;
tcp_v4_md5_hash_hdr((__u8 *) &rep.opt[offset],
- key, ip_hdr(skb)->daddr,
- ip_hdr(skb)->saddr, &rep.th);
+ key, ip_hdr(skb)->saddr,
+ ip_hdr(skb)->daddr, &rep.th);
}
#endif
arg.csum = csum_tcpudp_nofold(ip_hdr(skb)->daddr,
inet_twsk_put(tw);
}
-static void tcp_v4_reqsk_send_ack(struct sk_buff *skb,
+static void tcp_v4_reqsk_send_ack(struct sock *sk, struct sk_buff *skb,
struct request_sock *req)
{
tcp_v4_send_ack(skb, tcp_rsk(req)->snt_isn + 1,
tcp_rsk(req)->rcv_isn + 1, req->rcv_wnd,
req->ts_recent,
0,
- tcp_v4_md5_do_lookup(skb->sk, ip_hdr(skb)->daddr));
+ tcp_v4_md5_do_lookup(sk, ip_hdr(skb)->daddr));
}
/*
return 0;
if (hash_expected && !hash_location) {
- LIMIT_NETDEBUG(KERN_INFO "MD5 Hash expected but NOT found "
- "(" NIPQUAD_FMT ", %d)->(" NIPQUAD_FMT ", %d)\n",
- NIPQUAD(iph->saddr), ntohs(th->source),
- NIPQUAD(iph->daddr), ntohs(th->dest));
+ NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_TCPMD5NOTFOUND);
return 1;
}
if (!hash_expected && hash_location) {
- LIMIT_NETDEBUG(KERN_INFO "MD5 Hash NOT expected but found "
- "(" NIPQUAD_FMT ", %d)->(" NIPQUAD_FMT ", %d)\n",
- NIPQUAD(iph->saddr), ntohs(th->source),
- NIPQUAD(iph->daddr), ntohs(th->dest));
+ NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_TCPMD5UNEXPECTED);
return 1;
}
tcp_rsk(req)->rcv_isn + 1, tcp_rsk(req)->rcv_isn + 1 + req->rcv_wnd)) {
/* Out of window: send ACK and drop. */
if (!(flg & TCP_FLAG_RST))
- req->rsk_ops->send_ack(skb, req);
+ req->rsk_ops->send_ack(sk, skb, req);
if (paws_reject)
NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_PAWSESTABREJECTED);
return NULL;
/* In sequence, PAWS is OK. */
if (tmp_opt.saw_tstamp && !after(TCP_SKB_CB(skb)->seq, tcp_rsk(req)->rcv_isn + 1))
- req->ts_recent = tmp_opt.rcv_tsval;
+ req->ts_recent = tmp_opt.rcv_tsval;
- if (TCP_SKB_CB(skb)->seq == tcp_rsk(req)->rcv_isn) {
- /* Truncate SYN, it is out of window starting
- at tcp_rsk(req)->rcv_isn + 1. */
- flg &= ~TCP_FLAG_SYN;
- }
+ if (TCP_SKB_CB(skb)->seq == tcp_rsk(req)->rcv_isn) {
+ /* Truncate SYN, it is out of window starting
+ at tcp_rsk(req)->rcv_isn + 1. */
+ flg &= ~TCP_FLAG_SYN;
+ }
- /* RFC793: "second check the RST bit" and
- * "fourth, check the SYN bit"
- */
- if (flg & (TCP_FLAG_RST|TCP_FLAG_SYN)) {
- TCP_INC_STATS_BH(sock_net(sk), TCP_MIB_ATTEMPTFAILS);
- goto embryonic_reset;
- }
+ /* RFC793: "second check the RST bit" and
+ * "fourth, check the SYN bit"
+ */
+ if (flg & (TCP_FLAG_RST|TCP_FLAG_SYN)) {
+ TCP_INC_STATS_BH(sock_net(sk), TCP_MIB_ATTEMPTFAILS);
+ goto embryonic_reset;
+ }
- /* ACK sequence verified above, just make sure ACK is
- * set. If ACK not set, just silently drop the packet.
- */
- if (!(flg & TCP_FLAG_ACK))
- return NULL;
-
- /* If TCP_DEFER_ACCEPT is set, drop bare ACK. */
- if (inet_csk(sk)->icsk_accept_queue.rskq_defer_accept &&
- TCP_SKB_CB(skb)->end_seq == tcp_rsk(req)->rcv_isn + 1) {
- inet_rsk(req)->acked = 1;
- return NULL;
- }
+ /* ACK sequence verified above, just make sure ACK is
+ * set. If ACK not set, just silently drop the packet.
+ */
+ if (!(flg & TCP_FLAG_ACK))
+ return NULL;
- /* OK, ACK is valid, create big socket and
- * feed this segment to it. It will repeat all
- * the tests. THIS SEGMENT MUST MOVE SOCKET TO
- * ESTABLISHED STATE. If it will be dropped after
- * socket is created, wait for troubles.
- */
- child = inet_csk(sk)->icsk_af_ops->syn_recv_sock(sk, skb,
- req, NULL);
- if (child == NULL)
- goto listen_overflow;
+ /* If TCP_DEFER_ACCEPT is set, drop bare ACK. */
+ if (inet_csk(sk)->icsk_accept_queue.rskq_defer_accept &&
+ TCP_SKB_CB(skb)->end_seq == tcp_rsk(req)->rcv_isn + 1) {
+ inet_rsk(req)->acked = 1;
+ return NULL;
+ }
+
+ /* OK, ACK is valid, create big socket and
+ * feed this segment to it. It will repeat all
+ * the tests. THIS SEGMENT MUST MOVE SOCKET TO
+ * ESTABLISHED STATE. If it will be dropped after
+ * socket is created, wait for troubles.
+ */
+ child = inet_csk(sk)->icsk_af_ops->syn_recv_sock(sk, skb, req, NULL);
+ if (child == NULL)
+ goto listen_overflow;
#ifdef CONFIG_TCP_MD5SIG
- else {
- /* Copy over the MD5 key from the original socket */
- struct tcp_md5sig_key *key;
- struct tcp_sock *tp = tcp_sk(sk);
- key = tp->af_specific->md5_lookup(sk, child);
- if (key != NULL) {
- /*
- * We're using one, so create a matching key on the
- * newsk structure. If we fail to get memory then we
- * end up not copying the key across. Shucks.
- */
- char *newkey = kmemdup(key->key, key->keylen,
- GFP_ATOMIC);
- if (newkey) {
- if (!tcp_alloc_md5sig_pool())
- BUG();
- tp->af_specific->md5_add(child, child,
- newkey,
- key->keylen);
- }
+ else {
+ /* Copy over the MD5 key from the original socket */
+ struct tcp_md5sig_key *key;
+ struct tcp_sock *tp = tcp_sk(sk);
+ key = tp->af_specific->md5_lookup(sk, child);
+ if (key != NULL) {
+ /*
+ * We're using one, so create a matching key on the
+ * newsk structure. If we fail to get memory then we
+ * end up not copying the key across. Shucks.
+ */
+ char *newkey = kmemdup(key->key, key->keylen,
+ GFP_ATOMIC);
+ if (newkey) {
+ if (!tcp_alloc_md5sig_pool())
+ BUG();
+ tp->af_specific->md5_add(child, child, newkey,
+ key->keylen);
}
}
+ }
#endif
- inet_csk_reqsk_queue_unlink(sk, req, prev);
- inet_csk_reqsk_queue_removed(sk, req);
+ inet_csk_reqsk_queue_unlink(sk, req, prev);
+ inet_csk_reqsk_queue_removed(sk, req);
- inet_csk_reqsk_queue_add(sk, req, child);
- return child;
+ inet_csk_reqsk_queue_add(sk, req, child);
+ return child;
- listen_overflow:
- if (!sysctl_tcp_abort_on_overflow) {
- inet_rsk(req)->acked = 1;
- return NULL;
- }
+listen_overflow:
+ if (!sysctl_tcp_abort_on_overflow) {
+ inet_rsk(req)->acked = 1;
+ return NULL;
+ }
- embryonic_reset:
- NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_EMBRYONICRSTS);
- if (!(flg & TCP_FLAG_RST))
- req->rsk_ops->send_reset(sk, skb);
+embryonic_reset:
+ NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_EMBRYONICRSTS);
+ if (!(flg & TCP_FLAG_RST))
+ req->rsk_ops->send_reset(sk, skb);
- inet_csk_reqsk_queue_drop(sk, req, prev);
- return NULL;
+ inet_csk_reqsk_queue_drop(sk, req, prev);
+ return NULL;
}
/*
if (unlikely(optlen))
hdrlen += IPV4_BEET_PHMAXLEN - (optlen & 4);
- skb_set_network_header(skb, IPV4_BEET_PHMAXLEN - x->props.header_len -
- hdrlen);
+ skb_set_network_header(skb, -x->props.header_len -
+ hdrlen + (XFRM_MODE_SKB_CB(skb)->ihl - sizeof(*top_iph)));
+ if (x->sel.family != AF_INET6)
+ skb->network_header += IPV4_BEET_PHMAXLEN;
skb->mac_header = skb->network_header +
offsetof(struct iphdr, protocol);
skb->transport_header = skb->network_header + sizeof(*top_iph);
LIMIT_NETDEBUG(KERN_DEBUG "invalid cmsg type: %d\n",
cmsg->cmsg_type);
err = -EINVAL;
- break;
+ goto exit_f;
}
}
crypto_aead_ivsize(aead);
switch (x->props.mode) {
case XFRM_MODE_BEET:
+ if (x->sel.family != AF_INET6)
+ x->props.header_len += IPV4_BEET_PHMAXLEN +
+ (sizeof(struct ipv6hdr) - sizeof(struct iphdr));
+ break;
case XFRM_MODE_TRANSPORT:
break;
case XFRM_MODE_TUNNEL:
skb_reset_network_header(skb);
hdr = ipv6_hdr(skb);
+ /* Allow local fragmentation. */
+ if (ipfragok)
+ skb->local_df = 1;
+
/*
* Fill in the IPv6 header
*/
skb->mark = sk->sk_mark;
mtu = dst_mtu(dst);
- if ((skb->len <= mtu) || ipfragok || skb_is_gso(skb)) {
+ if ((skb->len <= mtu) || skb->local_df || skb_is_gso(skb)) {
IP6_INC_STATS(ip6_dst_idev(skb->dst),
IPSTATS_MIB_OUTREQUESTS);
return NF_HOOK(PF_INET6, NF_INET_LOCAL_OUT, skb, NULL, dst->dev,
*/
if (optlen == 0)
optval = NULL;
+ else if (optval == NULL)
+ goto e_inval;
else if (optlen < sizeof(struct ipv6_opt_hdr) ||
optlen & 0x7 || optlen > 8 * 255)
goto e_inval;
void ipv6_misc_proc_exit(void)
{
- proc_net_remove(&init_net, "sockstat6");
proc_net_remove(&init_net, "dev_snmp6");
proc_net_remove(&init_net, "snmp6");
unregister_pernet_subsys(&ipv6_proc_ops);
if (dst_metric(&rt->u.dst, RTAX_HOPLIMIT) == 0)
rt->u.dst.metrics[RTAX_HOPLIMIT-1] = -1;
- if (!dst_metric(&rt->u.dst, RTAX_MTU))
+ if (!dst_mtu(&rt->u.dst))
rt->u.dst.metrics[RTAX_MTU-1] = ipv6_get_mtu(dev);
if (!dst_metric(&rt->u.dst, RTAX_ADVMSS))
rt->u.dst.metrics[RTAX_ADVMSS-1] = ipv6_advmss(net, dst_mtu(&rt->u.dst));
ireq6 = inet6_rsk(req);
treq = tcp_rsk(req);
- if (security_inet_conn_request(sk, skb, req)) {
- reqsk_free(req);
- goto out;
- }
+ if (security_inet_conn_request(sk, skb, req))
+ goto out_free;
req->mss = mss;
ireq->rmt_port = th->source;
fl.fl_ip_dport = inet_rsk(req)->rmt_port;
fl.fl_ip_sport = inet_sk(sk)->sport;
security_req_classify_flow(req, &fl);
- if (ip6_dst_lookup(sk, &dst, &fl)) {
- reqsk_free(req);
- goto out;
- }
+ if (ip6_dst_lookup(sk, &dst, &fl))
+ goto out_free;
+
if (final_p)
ipv6_addr_copy(&fl.fl6_dst, final_p);
if ((xfrm_lookup(&dst, &fl, sk, 0)) < 0)
- goto out;
+ goto out_free;
}
req->window_clamp = tp->window_clamp ? :dst_metric(dst, RTAX_WINDOW);
ireq->rcv_wscale = rcv_wscale;
ret = get_cookie_sock(sk, skb, req, dst);
-
-out: return ret;
+out:
+ return ret;
+out_free:
+ reqsk_free(req);
+ return NULL;
}
#include <linux/scatterlist.h>
static void tcp_v6_send_reset(struct sock *sk, struct sk_buff *skb);
-static void tcp_v6_reqsk_send_ack(struct sk_buff *skb, struct request_sock *req);
+static void tcp_v6_reqsk_send_ack(struct sock *sk, struct sk_buff *skb,
+ struct request_sock *req);
static int tcp_v6_do_rcv(struct sock *sk, struct sk_buff *skb);
ipv6_addr_copy(&bp->saddr, saddr);
ipv6_addr_copy(&bp->daddr, daddr);
bp->protocol = cpu_to_be32(IPPROTO_TCP);
- bp->len = cpu_to_be16(nbytes);
+ bp->len = cpu_to_be32(nbytes);
sg_init_one(&sg, bp, sizeof(*bp));
return crypto_hash_update(&hp->md5_desc, &sg, sizeof(*bp));
hash_expected = tcp_v6_md5_do_lookup(sk, &ip6h->saddr);
hash_location = tcp_parse_md5sig_option(th);
- /* do we have a hash as expected? */
- if (!hash_expected) {
- if (!hash_location)
- return 0;
- if (net_ratelimit()) {
- printk(KERN_INFO "MD5 Hash NOT expected but found "
- "(" NIP6_FMT ", %u)->"
- "(" NIP6_FMT ", %u)\n",
- NIP6(ip6h->saddr), ntohs(th->source),
- NIP6(ip6h->daddr), ntohs(th->dest));
- }
+ /* We've parsed the options - do we have a hash? */
+ if (!hash_expected && !hash_location)
+ return 0;
+
+ if (hash_expected && !hash_location) {
+ NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_TCPMD5NOTFOUND);
return 1;
}
- if (!hash_location) {
- if (net_ratelimit()) {
- printk(KERN_INFO "MD5 Hash expected but NOT found "
- "(" NIP6_FMT ", %u)->"
- "(" NIP6_FMT ", %u)\n",
- NIP6(ip6h->saddr), ntohs(th->source),
- NIP6(ip6h->daddr), ntohs(th->dest));
- }
+ if (!hash_expected && hash_location) {
+ NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_TCPMD5UNEXPECTED);
return 1;
}
*topt++ = htonl((TCPOPT_NOP << 24) | (TCPOPT_NOP << 16) |
(TCPOPT_MD5SIG << 8) | TCPOLEN_MD5SIG);
tcp_v6_md5_hash_hdr((__u8 *)topt, key,
- &ipv6_hdr(skb)->daddr,
- &ipv6_hdr(skb)->saddr, t1);
+ &ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr, t1);
}
#endif
inet_twsk_put(tw);
}
-static void tcp_v6_reqsk_send_ack(struct sk_buff *skb, struct request_sock *req)
+static void tcp_v6_reqsk_send_ack(struct sock *sk, struct sk_buff *skb,
+ struct request_sock *req)
{
tcp_v6_send_ack(skb, tcp_rsk(req)->snt_isn + 1, tcp_rsk(req)->rcv_isn + 1, req->rcv_wnd, req->ts_recent,
- tcp_v6_md5_do_lookup(skb->sk, &ipv6_hdr(skb)->daddr));
+ tcp_v6_md5_do_lookup(sk, &ipv6_hdr(skb)->daddr));
}
static int xfrm6_beet_output(struct xfrm_state *x, struct sk_buff *skb)
{
struct ipv6hdr *top_iph;
-
- skb_set_network_header(skb, -x->props.header_len);
+ struct ip_beet_phdr *ph;
+ struct iphdr *iphv4;
+ int optlen, hdr_len;
+
+ iphv4 = ip_hdr(skb);
+ hdr_len = 0;
+ optlen = XFRM_MODE_SKB_CB(skb)->optlen;
+ if (unlikely(optlen))
+ hdr_len += IPV4_BEET_PHMAXLEN - (optlen & 4);
+
+ skb_set_network_header(skb, -x->props.header_len - hdr_len);
+ if (x->sel.family != AF_INET6)
+ skb->network_header += IPV4_BEET_PHMAXLEN;
skb->mac_header = skb->network_header +
offsetof(struct ipv6hdr, nexthdr);
skb->transport_header = skb->network_header + sizeof(*top_iph);
- __skb_pull(skb, XFRM_MODE_SKB_CB(skb)->ihl);
+ ph = (struct ip_beet_phdr *)__skb_pull(skb, XFRM_MODE_SKB_CB(skb)->ihl-hdr_len);
xfrm6_beet_make_header(skb);
top_iph = ipv6_hdr(skb);
+ if (unlikely(optlen)) {
+
+ BUG_ON(optlen < 0);
+
+ ph->padlen = 4 - (optlen & 4);
+ ph->hdrlen = optlen / 8;
+ ph->nexthdr = top_iph->nexthdr;
+ if (ph->padlen)
+ memset(ph + 1, IPOPT_NOP, ph->padlen);
+
+ top_iph->nexthdr = IPPROTO_BEETPH;
+ }
ipv6_addr_copy(&top_iph->saddr, (struct in6_addr *)&x->props.saddr);
ipv6_addr_copy(&top_iph->daddr, (struct in6_addr *)&x->id.daddr);
enum nl80211_iftype type, u32 *flags,
struct vif_params *params)
{
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct net_device *dev;
enum ieee80211_if_types itype;
struct ieee80211_sub_if_data *sdata;
if (itype == IEEE80211_IF_TYPE_INVALID)
return -EINVAL;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
sdata = IEEE80211_DEV_TO_SUB_IF(dev);
ret = ieee80211_if_change_type(sdata, itype);
u8 key_idx, u8 *mac_addr,
struct key_params *params)
{
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta = NULL;
enum ieee80211_key_alg alg;
struct ieee80211_key *key;
int err;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
sdata = IEEE80211_DEV_TO_SUB_IF(dev);
switch (params->cipher) {
static int ieee80211_del_key(struct wiphy *wiphy, struct net_device *dev,
u8 key_idx, u8 *mac_addr)
{
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
int ret;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
sdata = IEEE80211_DEV_TO_SUB_IF(dev);
rcu_read_lock();
void (*callback)(void *cookie,
struct key_params *params))
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct sta_info *sta = NULL;
u8 seq[6] = {0};
struct key_params params;
u16 iv16;
int err = -ENOENT;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
rcu_read_lock();
if (mac_addr) {
struct net_device *dev,
u8 key_idx)
{
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct ieee80211_sub_if_data *sdata;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
rcu_read_lock();
sdata = IEEE80211_DEV_TO_SUB_IF(dev);
static int ieee80211_add_beacon(struct wiphy *wiphy, struct net_device *dev,
struct beacon_parameters *params)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct beacon_data *old;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_AP)
return -EINVAL;
static int ieee80211_set_beacon(struct wiphy *wiphy, struct net_device *dev,
struct beacon_parameters *params)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct beacon_data *old;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_AP)
return -EINVAL;
static int ieee80211_del_beacon(struct wiphy *wiphy, struct net_device *dev)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct beacon_data *old;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_AP)
return -EINVAL;
static int ieee80211_add_station(struct wiphy *wiphy, struct net_device *dev,
u8 *mac, struct station_parameters *params)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct sta_info *sta;
struct ieee80211_sub_if_data *sdata;
int err;
+ if (dev == local->mdev || params->vlan == local->mdev)
+ return -EOPNOTSUPP;
+
/* Prevent a race with changing the rate control algorithm */
if (!netif_running(dev))
return -ENETDOWN;
static int ieee80211_del_station(struct wiphy *wiphy, struct net_device *dev,
u8 *mac)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
- struct ieee80211_local *local = sdata->local;
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (mac) {
rcu_read_lock();
u8 *mac,
struct station_parameters *params)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
struct sta_info *sta;
struct ieee80211_sub_if_data *vlansdata;
+ if (dev == local->mdev || params->vlan == local->mdev)
+ return -EOPNOTSUPP;
+
rcu_read_lock();
/* XXX: get sta belonging to dev */
return -EINVAL;
}
- sta->sdata = IEEE80211_DEV_TO_SUB_IF(params->vlan);
+ sta->sdata = vlansdata;
ieee80211_send_layer2_update(sta);
}
static int ieee80211_add_mpath(struct wiphy *wiphy, struct net_device *dev,
u8 *dst, u8 *next_hop)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct mesh_path *mpath;
struct sta_info *sta;
int err;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
if (!netif_running(dev))
return -ENETDOWN;
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_MESH_POINT)
return -ENOTSUPP;
struct net_device *dev,
u8 *dst, u8 *next_hop)
{
- struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct mesh_path *mpath;
struct sta_info *sta;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
if (!netif_running(dev))
return -ENETDOWN;
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_MESH_POINT)
return -ENOTSUPP;
u8 *dst, u8 *next_hop, struct mpath_info *pinfo)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct mesh_path *mpath;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_MESH_POINT)
return -ENOTSUPP;
int idx, u8 *dst, u8 *next_hop,
struct mpath_info *pinfo)
{
- struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_local *local = wiphy_priv(wiphy);
+ struct ieee80211_sub_if_data *sdata;
struct mesh_path *mpath;
+ if (dev == local->mdev)
+ return -EOPNOTSUPP;
+
+ sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+
if (sdata->vif.type != IEEE80211_IF_TYPE_MESH_POINT)
return -ENOTSUPP;
u8 bssid[ETH_ALEN];
u8 ssid[IEEE80211_MAX_SSID_LEN];
+ u8 dtim_period;
u16 capability; /* host byte order */
enum ieee80211_band band;
int freq;
struct timer_list sta_cleanup;
unsigned long queues_pending[BITS_TO_LONGS(IEEE80211_MAX_QUEUES)];
+ unsigned long queues_pending_run[BITS_TO_LONGS(IEEE80211_MAX_QUEUES)];
struct ieee80211_tx_stored_packet pending_packet[IEEE80211_MAX_QUEUES];
struct tasklet_struct tx_pending_tasklet;
case IEEE80211_IF_TYPE_AP:
sdata->bss = &sdata->u.ap;
break;
+ case IEEE80211_IF_TYPE_MESH_POINT:
+ /* mesh ifaces must set allmulti to forward mcast traffic */
+ atomic_inc(&local->iff_allmultis);
+ break;
case IEEE80211_IF_TYPE_STA:
case IEEE80211_IF_TYPE_MNTR:
case IEEE80211_IF_TYPE_IBSS:
- case IEEE80211_IF_TYPE_MESH_POINT:
/* no special treatment */
break;
case IEEE80211_IF_TYPE_INVALID:
netif_addr_unlock_bh(local->mdev);
break;
case IEEE80211_IF_TYPE_MESH_POINT:
+ /* allmulti is always set on mesh ifaces */
+ atomic_dec(&local->iff_allmultis);
+ /* fall through */
case IEEE80211_IF_TYPE_STA:
case IEEE80211_IF_TYPE_IBSS:
sdata->u.sta.state = IEEE80211_DISABLED;
/* Remove added headers (e.g., QoS control), encryption header/MIC, etc. to
* make a prepared TX frame (one that has been given to hw) to look like brand
* new IEEE 802.11 frame that is ready to go through TX processing again.
- * Also, tx_packet_data in cb is restored from tx_control. */
+ */
static void ieee80211_remove_tx_extra(struct ieee80211_local *local,
struct ieee80211_key *key,
struct sk_buff *skb)
{
int hdrlen, iv_len, mic_len;
- struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
-
- info->flags &= IEEE80211_TX_CTL_REQ_TX_STATUS |
- IEEE80211_TX_CTL_DO_NOT_ENCRYPT |
- IEEE80211_TX_CTL_REQUEUE |
- IEEE80211_TX_CTL_EAPOL_FRAME;
hdrlen = ieee80211_get_hdrlen_from_skb(skb);
if (local->hw.conf.beacon_int < 10)
local->hw.conf.beacon_int = 100;
+ if (local->hw.max_listen_interval == 0)
+ local->hw.max_listen_interval = 1;
+
+ local->hw.conf.listen_interval = local->hw.max_listen_interval;
+
local->wstats_flags |= local->hw.flags & (IEEE80211_HW_SIGNAL_UNSPEC |
IEEE80211_HW_SIGNAL_DB |
IEEE80211_HW_SIGNAL_DBM) ?
result = ieee80211_wep_init(local);
if (result < 0) {
- printk(KERN_DEBUG "%s: Failed to initialize wep\n",
- wiphy_name(local->hw.wiphy));
+ printk(KERN_DEBUG "%s: Failed to initialize wep: %d\n",
+ wiphy_name(local->hw.wiphy), result);
goto fail_wep;
}
void ieee80211_mesh_init_sdata(struct ieee80211_sub_if_data *sdata);
/* Mesh paths */
-int mesh_nexthop_lookup(u8 *next_hop, struct sk_buff *skb,
- struct net_device *dev);
+int mesh_nexthop_lookup(struct sk_buff *skb, struct net_device *dev);
void mesh_path_start_discovery(struct net_device *dev);
struct mesh_path *mesh_path_lookup(u8 *dst, struct net_device *dev);
struct mesh_path *mesh_path_lookup_by_idx(int idx, struct net_device *dev);
#define mesh_allocated 0
#endif
-#define MESH_PREQ(skb) (skb->cb + 30)
-
#endif /* IEEE80211S_H */
/**
* ieee80211s_lookup_nexthop - put the appropriate next hop on a mesh frame
*
- * @next_hop: output argument for next hop address
- * @skb: frame to be sent
+ * @skb: 802.11 frame to be sent
* @dev: network device the frame will be sent through
+ * @fwd_frame: true if this frame was originally from a different host
*
* Returns: 0 if the next hop was found. Nonzero otherwise. If no next hop is
* found, the function will start a path discovery and queue the frame so it is
* sent when the path is resolved. This means the caller must not free the skb
* in this case.
*/
-int mesh_nexthop_lookup(u8 *next_hop, struct sk_buff *skb,
- struct net_device *dev)
+int mesh_nexthop_lookup(struct sk_buff *skb, struct net_device *dev)
{
struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
struct sk_buff *skb_to_free = NULL;
struct mesh_path *mpath;
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
+ u8 *dst_addr = hdr->addr3;
int err = 0;
rcu_read_lock();
- mpath = mesh_path_lookup(skb->data, dev);
+ mpath = mesh_path_lookup(dst_addr, dev);
if (!mpath) {
- mesh_path_add(skb->data, dev);
- mpath = mesh_path_lookup(skb->data, dev);
+ mesh_path_add(dst_addr, dev);
+ mpath = mesh_path_lookup(dst_addr, dev);
if (!mpath) {
dev_kfree_skb(skb);
sdata->u.sta.mshstats.dropped_frames_no_route++;
if (mpath->flags & MESH_PATH_ACTIVE) {
if (time_after(jiffies, mpath->exp_time -
msecs_to_jiffies(sdata->u.sta.mshcfg.path_refresh_time))
- && skb->pkt_type != PACKET_OTHERHOST
+ && !memcmp(dev->dev_addr, hdr->addr4, ETH_ALEN)
&& !(mpath->flags & MESH_PATH_RESOLVING)
&& !(mpath->flags & MESH_PATH_FIXED)) {
mesh_queue_preq(mpath,
PREQ_Q_F_START | PREQ_Q_F_REFRESH);
}
- memcpy(next_hop, mpath->next_hop->addr,
+ memcpy(hdr->addr1, mpath->next_hop->addr,
ETH_ALEN);
} else {
if (!(mpath->flags & MESH_PATH_RESOLVING)) {
void mesh_path_discard_frame(struct sk_buff *skb, struct net_device *dev)
{
struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev);
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
struct mesh_path *mpath;
u32 dsn = 0;
- if (skb->pkt_type == PACKET_OTHERHOST) {
- struct ieee80211s_hdr *prev_meshhdr;
- int mshhdrlen;
+ if (memcmp(hdr->addr4, dev->dev_addr, ETH_ALEN) != 0) {
u8 *ra, *da;
- prev_meshhdr = ((struct ieee80211s_hdr *)skb->cb);
- mshhdrlen = ieee80211_get_mesh_hdrlen(prev_meshhdr);
- da = skb->data;
- ra = MESH_PREQ(skb);
+ da = hdr->addr3;
+ ra = hdr->addr2;
mpath = mesh_path_lookup(da, dev);
if (mpath)
dsn = ++mpath->dsn;
/* set timing information */
sdata->bss_conf.beacon_int = bss->beacon_int;
sdata->bss_conf.timestamp = bss->timestamp;
+ sdata->bss_conf.dtim_period = bss->dtim_period;
changed |= ieee80211_handle_bss_capability(sdata, bss);
int encrypt)
{
struct ieee80211_sub_if_data *sdata;
- struct ieee80211_tx_info *info;
sdata = IEEE80211_DEV_TO_SUB_IF(dev);
skb->dev = sdata->local->mdev;
skb_set_network_header(skb, 0);
skb_set_transport_header(skb, 0);
- info = IEEE80211_SKB_CB(skb);
- memset(info, 0, sizeof(struct ieee80211_tx_info));
- info->control.ifindex = sdata->dev->ifindex;
- if (!encrypt)
- info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ skb->iif = sdata->dev->ifindex;
+ skb->do_not_encrypt = !encrypt;
dev_queue_xmit(skb);
}
mgmt->frame_control = IEEE80211_FC(IEEE80211_FTYPE_MGMT,
IEEE80211_STYPE_REASSOC_REQ);
mgmt->u.reassoc_req.capab_info = cpu_to_le16(capab);
- mgmt->u.reassoc_req.listen_interval = cpu_to_le16(1);
+ mgmt->u.reassoc_req.listen_interval =
+ cpu_to_le16(local->hw.conf.listen_interval);
memcpy(mgmt->u.reassoc_req.current_ap, ifsta->prev_bssid,
ETH_ALEN);
} else {
mgmt->frame_control = IEEE80211_FC(IEEE80211_FTYPE_MGMT,
IEEE80211_STYPE_ASSOC_REQ);
mgmt->u.assoc_req.capab_info = cpu_to_le16(capab);
- mgmt->u.assoc_req.listen_interval = cpu_to_le16(1);
+ mgmt->u.reassoc_req.listen_interval =
+ cpu_to_le16(local->hw.conf.listen_interval);
}
/* SSID */
bss->beacon_int = le16_to_cpu(mgmt->u.beacon.beacon_int);
bss->capability = le16_to_cpu(mgmt->u.beacon.capab_info);
+ if (elems->tim) {
+ struct ieee80211_tim_ie *tim_ie =
+ (struct ieee80211_tim_ie *)elems->tim;
+ bss->dtim_period = tim_ie->dtim_period;
+ }
+
+ /* set default value for buggy APs */
+ if (!elems->tim || bss->dtim_period == 0)
+ bss->dtim_period = 1;
+
bss->supp_rates_len = 0;
if (elems->supp_rates) {
clen = IEEE80211_MAX_SUPP_RATES - bss->supp_rates_len;
ifsta = &sdata->u.sta;
ifsta->state = IEEE80211_MESH_UP;
ieee80211_sta_timer((unsigned long)sdata);
+ ieee80211_if_config(sdata, IEEE80211_IFCC_BEACON);
}
#endif
"%s\n", print_mac(mac, bssid),
print_mac(mac2, ifsta->bssid));
#endif /* CONFIG_MAC80211_IBSS_DEBUG */
- if (found && memcmp(ifsta->bssid, bssid, ETH_ALEN) != 0 &&
- (bss = ieee80211_rx_bss_get(dev, bssid,
- local->hw.conf.channel->center_freq,
- ifsta->ssid, ifsta->ssid_len))) {
+
+ if (found && memcmp(ifsta->bssid, bssid, ETH_ALEN) != 0) {
int ret;
+ int search_freq;
+
+ if (ifsta->flags & IEEE80211_STA_AUTO_CHANNEL_SEL)
+ search_freq = bss->freq;
+ else
+ search_freq = local->hw.conf.channel->center_freq;
+
+ bss = ieee80211_rx_bss_get(dev, bssid, search_freq,
+ ifsta->ssid, ifsta->ssid_len);
+ if (!bss)
+ goto dont_join;
+
printk(KERN_DEBUG "%s: Selected IBSS BSSID %s"
" based on configured SSID\n",
dev->name, print_mac(mac, bssid));
ieee80211_rx_bss_put(local, bss);
return ret;
}
+
+dont_join:
#ifdef CONFIG_MAC80211_IBSS_DEBUG
printk(KERN_DEBUG " did not try to join ibss\n");
#endif /* CONFIG_MAC80211_IBSS_DEBUG */
if (sdata->vif.type == IEEE80211_IF_TYPE_IBSS) {
struct ieee80211_if_sta *ifsta = &sdata->u.sta;
if (!(ifsta->flags & IEEE80211_STA_BSSID_SET) ||
- (!ifsta->state == IEEE80211_IBSS_JOINED &&
+ (!(ifsta->state == IEEE80211_IBSS_JOINED) &&
!ieee80211_sta_active_ibss(dev)))
ieee80211_sta_find_ibss(dev, ifsta);
}
hdrlen = ieee80211_get_hdrlen(fc);
- if (ieee80211_vif_is_mesh(&sdata->vif)) {
- int meshhdrlen = ieee80211_get_mesh_hdrlen(
+ if (ieee80211_vif_is_mesh(&sdata->vif))
+ hdrlen += ieee80211_get_mesh_hdrlen(
(struct ieee80211s_hdr *) (skb->data + hdrlen));
- /* Copy on cb:
- * - mesh header: to be used for mesh forwarding
- * decision. It will also be used as mesh header template at
- * tx.c:ieee80211_subif_start_xmit() if interface
- * type is mesh and skb->pkt_type == PACKET_OTHERHOST
- * - ta: to be used if a RERR needs to be sent.
- */
- memcpy(skb->cb, skb->data + hdrlen, meshhdrlen);
- memcpy(MESH_PREQ(skb), hdr->addr2, ETH_ALEN);
- hdrlen += meshhdrlen;
- }
/* convert IEEE 802.11 header + possible LLC headers into Ethernet
* header
}
}
- /* Mesh forwarding */
- if (ieee80211_vif_is_mesh(&sdata->vif)) {
- u8 *mesh_ttl = &((struct ieee80211s_hdr *)skb->cb)->ttl;
- (*mesh_ttl)--;
-
- if (is_multicast_ether_addr(skb->data)) {
- if (*mesh_ttl > 0) {
- xmit_skb = skb_copy(skb, GFP_ATOMIC);
- if (xmit_skb)
- xmit_skb->pkt_type = PACKET_OTHERHOST;
- else if (net_ratelimit())
- printk(KERN_DEBUG "%s: failed to clone "
- "multicast frame\n", dev->name);
- } else
- IEEE80211_IFSTA_MESH_CTR_INC(&sdata->u.sta,
- dropped_frames_ttl);
- } else if (skb->pkt_type != PACKET_OTHERHOST &&
- compare_ether_addr(dev->dev_addr, skb->data) != 0) {
- if (*mesh_ttl == 0) {
- IEEE80211_IFSTA_MESH_CTR_INC(&sdata->u.sta,
- dropped_frames_ttl);
- dev_kfree_skb(skb);
- skb = NULL;
- } else {
- xmit_skb = skb;
- xmit_skb->pkt_type = PACKET_OTHERHOST;
- if (!(dev->flags & IFF_PROMISC))
- skb = NULL;
- }
- }
- }
-
if (skb) {
/* deliver to local stack */
skb->protocol = eth_type_trans(skb, dev);
return RX_QUEUED;
}
+static ieee80211_rx_result debug_noinline
+ieee80211_rx_h_mesh_fwding(struct ieee80211_rx_data *rx)
+{
+ struct ieee80211_hdr *hdr;
+ struct ieee80211s_hdr *mesh_hdr;
+ unsigned int hdrlen;
+ struct sk_buff *skb = rx->skb, *fwd_skb;
+
+ hdr = (struct ieee80211_hdr *) skb->data;
+ hdrlen = ieee80211_hdrlen(hdr->frame_control);
+ mesh_hdr = (struct ieee80211s_hdr *) (skb->data + hdrlen);
+
+ if (!ieee80211_is_data(hdr->frame_control))
+ return RX_CONTINUE;
+
+ if (!mesh_hdr->ttl)
+ /* illegal frame */
+ return RX_DROP_MONITOR;
+
+ if (compare_ether_addr(rx->dev->dev_addr, hdr->addr3) == 0)
+ return RX_CONTINUE;
+
+ mesh_hdr->ttl--;
+
+ if (rx->flags & IEEE80211_RX_RA_MATCH) {
+ if (!mesh_hdr->ttl)
+ IEEE80211_IFSTA_MESH_CTR_INC(&rx->sdata->u.sta,
+ dropped_frames_ttl);
+ else {
+ struct ieee80211_hdr *fwd_hdr;
+ fwd_skb = skb_copy(skb, GFP_ATOMIC);
+
+ if (!fwd_skb && net_ratelimit())
+ printk(KERN_DEBUG "%s: failed to clone mesh frame\n",
+ rx->dev->name);
+
+ fwd_hdr = (struct ieee80211_hdr *) fwd_skb->data;
+ /*
+ * Save TA to addr1 to send TA a path error if a
+ * suitable next hop is not found
+ */
+ memcpy(fwd_hdr->addr1, fwd_hdr->addr2, ETH_ALEN);
+ memcpy(fwd_hdr->addr2, rx->dev->dev_addr, ETH_ALEN);
+ fwd_skb->dev = rx->local->mdev;
+ fwd_skb->iif = rx->dev->ifindex;
+ dev_queue_xmit(fwd_skb);
+ }
+ }
+
+ if (is_multicast_ether_addr(hdr->addr3) ||
+ rx->dev->flags & IFF_PROMISC)
+ return RX_CONTINUE;
+ else
+ return RX_DROP_MONITOR;
+}
+
+
static ieee80211_rx_result debug_noinline
ieee80211_rx_h_data(struct ieee80211_rx_data *rx)
{
rx->sdata = sdata;
rx->dev = sdata->dev;
-#define CALL_RXH(rxh) \
- res = rxh(rx); \
- if (res != RX_CONTINUE) \
- goto rxh_done;
+#define CALL_RXH(rxh) \
+ do { \
+ res = rxh(rx); \
+ if (res != RX_CONTINUE) \
+ goto rxh_done; \
+ } while (0);
CALL_RXH(ieee80211_rx_h_passive_scan)
CALL_RXH(ieee80211_rx_h_check)
/* must be after MMIC verify so header is counted in MPDU mic */
CALL_RXH(ieee80211_rx_h_remove_qos_control)
CALL_RXH(ieee80211_rx_h_amsdu)
+ if (ieee80211_vif_is_mesh(&sdata->vif))
+ CALL_RXH(ieee80211_rx_h_mesh_fwding);
CALL_RXH(ieee80211_rx_h_data)
CALL_RXH(ieee80211_rx_h_ctrl)
CALL_RXH(ieee80211_rx_h_mgmt)
rcu_read_unlock();
local->total_ps_buffered = total;
-#ifdef MAC80211_VERBOSE_PS_DEBUG
+#ifdef CONFIG_MAC80211_VERBOSE_PS_DEBUG
printk(KERN_DEBUG "%s: PS buffers full - purged %d frames\n",
wiphy_name(local->hw.wiphy), purged);
#endif
purge_old_ps_buffers(tx->local);
if (skb_queue_len(&tx->sdata->bss->ps_bc_buf) >=
AP_MAX_BC_BUFFER) {
-#ifdef MAC80211_VERBOSE_PS_DEBUG
+#ifdef CONFIG_MAC80211_VERBOSE_PS_DEBUG
if (net_ratelimit()) {
printk(KERN_DEBUG "%s: BC TX buffer full - "
"dropping the oldest frame\n",
purge_old_ps_buffers(tx->local);
if (skb_queue_len(&sta->ps_tx_buf) >= STA_MAX_TX_BUFFER) {
struct sk_buff *old = skb_dequeue(&sta->ps_tx_buf);
-#ifdef MAC80211_VERBOSE_PS_DEBUG
+#ifdef CONFIG_MAC80211_VERBOSE_PS_DEBUG
if (net_ratelimit()) {
printk(KERN_DEBUG "%s: STA %s TX "
"buffer full - dropping oldest frame\n",
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(tx->skb);
u16 fc = tx->fc;
- if (unlikely(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT))
+ if (unlikely(tx->skb->do_not_encrypt))
tx->key = NULL;
else if (tx->sta && (key = rcu_dereference(tx->sta->key)))
tx->key = key;
else if ((key = rcu_dereference(tx->sdata->default_key)))
tx->key = key;
else if (tx->sdata->drop_unencrypted &&
- !(info->flags & IEEE80211_TX_CTL_EAPOL_FRAME) &&
+ (tx->skb->protocol != cpu_to_be16(ETH_P_PAE)) &&
!(info->flags & IEEE80211_TX_CTL_INJECTED)) {
I802_DEBUG_INC(tx->local->tx_handlers_drop_unencrypted);
return TX_DROP;
}
if (!tx->key || !(tx->key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE))
- info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ tx->skb->do_not_encrypt = 1;
return TX_CONTINUE;
}
memcpy(skb_put(frag, copylen), pos, copylen);
memcpy(frag->cb, first->cb, sizeof(frag->cb));
skb_copy_queue_mapping(frag, first);
+ frag->do_not_encrypt = first->do_not_encrypt;
pos += copylen;
left -= copylen;
sband = tx->local->hw.wiphy->bands[tx->channel->band];
- info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ skb->do_not_encrypt = 1;
info->flags |= IEEE80211_TX_CTL_INJECTED;
tx->flags &= ~IEEE80211_TX_FRAGMENTED;
skb_trim(skb, skb->len - FCS_LEN);
}
if (*iterator.this_arg & IEEE80211_RADIOTAP_F_WEP)
- info->flags &=
- ~IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
+ tx->skb->do_not_encrypt = 0;
if (*iterator.this_arg & IEEE80211_RADIOTAP_F_FRAG)
tx->flags |= IEEE80211_TX_FRAGMENTED;
break;
struct sk_buff *skb,
struct net_device *mdev)
{
- struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct net_device *dev;
- dev = dev_get_by_index(&init_net, info->control.ifindex);
+ dev = dev_get_by_index(&init_net, skb->iif);
if (unlikely(dev && !is_ieee80211_device(dev, mdev))) {
dev_put(dev);
dev = NULL;
static int __ieee80211_tx(struct ieee80211_local *local, struct sk_buff *skb,
struct ieee80211_tx_data *tx)
{
- struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_tx_info *info;
int ret, i;
- if (netif_subqueue_stopped(local->mdev, skb))
- return IEEE80211_TX_AGAIN;
-
if (skb) {
+ if (netif_subqueue_stopped(local->mdev, skb))
+ return IEEE80211_TX_AGAIN;
+ info = IEEE80211_SKB_CB(skb);
+
ieee80211_dump_frame(wiphy_name(local->hw.wiphy),
"TX to low-level driver", skb);
ret = local->ops->tx(local_to_hw(local), skb);
if (ret == IEEE80211_TX_FRAG_AGAIN)
skb = NULL;
+
set_bit(queue, local->queues_pending);
smp_mb();
/*
struct net_device *dev)
{
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
struct net_device *odev = NULL;
struct ieee80211_sub_if_data *osdata;
int headroom;
bool may_encrypt;
int ret;
- if (info->control.ifindex)
- odev = dev_get_by_index(&init_net, info->control.ifindex);
+ if (skb->iif)
+ odev = dev_get_by_index(&init_net, skb->iif);
if (unlikely(odev && !is_ieee80211_device(odev, dev))) {
dev_put(odev);
odev = NULL;
return 0;
}
+ memset(info, 0, sizeof(*info));
+
+ info->flags |= IEEE80211_TX_CTL_REQ_TX_STATUS;
+
osdata = IEEE80211_DEV_TO_SUB_IF(odev);
- may_encrypt = !(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT);
+ if (ieee80211_vif_is_mesh(&osdata->vif) &&
+ ieee80211_is_data(hdr->frame_control)) {
+ if (ieee80211_is_data(hdr->frame_control)) {
+ if (is_multicast_ether_addr(hdr->addr3))
+ memcpy(hdr->addr1, hdr->addr3, ETH_ALEN);
+ else
+ if (mesh_nexthop_lookup(skb, odev))
+ return 0;
+ if (memcmp(odev->dev_addr, hdr->addr4, ETH_ALEN) != 0)
+ IEEE80211_IFSTA_MESH_CTR_INC(&osdata->u.sta,
+ fwded_frames);
+ }
+ }
+
+ may_encrypt = !skb->do_not_encrypt;
headroom = osdata->local->tx_headroom;
if (may_encrypt)
struct net_device *dev)
{
struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct ieee80211_radiotap_header *prthdr =
(struct ieee80211_radiotap_header *)skb->data;
u16 len_rthdr;
skb->dev = local->mdev;
/* needed because we set skb device to master */
- info->control.ifindex = dev->ifindex;
+ skb->iif = dev->ifindex;
- info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
- /* Interfaces should always request a status report */
- info->flags |= IEEE80211_TX_CTL_REQ_TX_STATUS;
+ /* sometimes we do encrypt injected frames, will be fixed
+ * up in radiotap parser if not wanted */
+ skb->do_not_encrypt = 0;
/*
* fix up the pointers accounting for the radiotap
struct net_device *dev)
{
struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr);
- struct ieee80211_tx_info *info;
struct ieee80211_sub_if_data *sdata;
int ret = 1, head_need;
u16 ethertype, hdrlen, meshhdrlen = 0;
case IEEE80211_IF_TYPE_MESH_POINT:
fc |= cpu_to_le16(IEEE80211_FCTL_FROMDS | IEEE80211_FCTL_TODS);
/* RA TA DA SA */
- if (is_multicast_ether_addr(skb->data))
- memcpy(hdr.addr1, skb->data, ETH_ALEN);
- else if (mesh_nexthop_lookup(hdr.addr1, skb, dev))
- return 0;
+ memset(hdr.addr1, 0, ETH_ALEN);
memcpy(hdr.addr2, dev->dev_addr, ETH_ALEN);
memcpy(hdr.addr3, skb->data, ETH_ALEN);
memcpy(hdr.addr4, skb->data + ETH_ALEN, ETH_ALEN);
- if (skb->pkt_type == PACKET_OTHERHOST) {
- /* Forwarded frame, keep mesh ttl and seqnum */
- struct ieee80211s_hdr *prev_meshhdr;
- prev_meshhdr = ((struct ieee80211s_hdr *)skb->cb);
- meshhdrlen = ieee80211_get_mesh_hdrlen(prev_meshhdr);
- memcpy(&mesh_hdr, prev_meshhdr, meshhdrlen);
- sdata->u.sta.mshstats.fwded_frames++;
- } else {
- if (!sdata->u.sta.mshcfg.dot11MeshTTL) {
- /* Do not send frames with mesh_ttl == 0 */
- sdata->u.sta.mshstats.dropped_frames_ttl++;
- ret = 0;
- goto fail;
- }
- meshhdrlen = ieee80211_new_mesh_header(&mesh_hdr,
- sdata);
+ if (!sdata->u.sta.mshcfg.dot11MeshTTL) {
+ /* Do not send frames with mesh_ttl == 0 */
+ sdata->u.sta.mshstats.dropped_frames_ttl++;
+ ret = 0;
+ goto fail;
}
+ meshhdrlen = ieee80211_new_mesh_header(&mesh_hdr, sdata);
hdrlen = 30;
break;
#endif
* Drop unicast frames to unauthorised stations unless they are
* EAPOL frames from the local station.
*/
- if (unlikely(!is_multicast_ether_addr(hdr.addr1) &&
+ if (!ieee80211_vif_is_mesh(&sdata->vif) &&
+ unlikely(!is_multicast_ether_addr(hdr.addr1) &&
!(sta_flags & WLAN_STA_AUTHORIZED) &&
!(ethertype == ETH_P_PAE &&
compare_ether_addr(dev->dev_addr,
nh_pos += hdrlen;
h_pos += hdrlen;
- info = IEEE80211_SKB_CB(skb);
- memset(info, 0, sizeof(*info));
- info->control.ifindex = dev->ifindex;
- if (ethertype == ETH_P_PAE)
- info->flags |= IEEE80211_TX_CTL_EAPOL_FRAME;
-
- /* Interfaces should always request a status report */
- info->flags |= IEEE80211_TX_CTL_REQ_TX_STATUS;
+ skb->iif = dev->ifindex;
skb->dev = local->mdev;
dev->stats.tx_packets++;
netif_tx_lock_bh(dev);
for (i = 0; i < ieee80211_num_regular_queues(&local->hw); i++) {
/* Check that this queue is ok */
- if (__netif_subqueue_stopped(local->mdev, i))
+ if (__netif_subqueue_stopped(local->mdev, i) &&
+ !test_bit(i, local->queues_pending_run))
continue;
if (!test_bit(i, local->queues_pending)) {
+ clear_bit(i, local->queues_pending_run);
ieee80211_wake_queue(&local->hw, i);
continue;
}
+ clear_bit(i, local->queues_pending_run);
+ netif_start_subqueue(local->mdev, i);
+
store = &local->pending_packet[i];
tx.extra_frag = store->extra_frag;
tx.num_extra_frag = store->num_extra_frag;
info = IEEE80211_SKB_CB(skb);
+ skb->do_not_encrypt = 1;
+
info->band = band;
rate_control_get_rate(local->mdev, sband, skb, &rsel);
"no rate found\n",
wiphy_name(local->hw.wiphy));
}
- dev_kfree_skb(skb);
+ dev_kfree_skb_any(skb);
skb = NULL;
goto out;
}
info->tx_rate_idx = rsel.rate_idx;
info->flags |= IEEE80211_TX_CTL_NO_ACK;
- info->flags |= IEEE80211_TX_CTL_DO_NOT_ENCRYPT;
info->flags |= IEEE80211_TX_CTL_CLEAR_PS_FILT;
info->flags |= IEEE80211_TX_CTL_ASSIGN_SEQ;
if (sdata->bss_conf.use_short_preamble &&
struct ieee80211_local *local = hw_to_local(hw);
if (test_bit(queue, local->queues_pending)) {
+ set_bit(queue, local->queues_pending_run);
tasklet_schedule(&local->tx_pending_tasklet);
} else {
netif_wake_subqueue(local->mdev, queue);
local->wep_tx_tfm = crypto_alloc_blkcipher("ecb(arc4)", 0,
CRYPTO_ALG_ASYNC);
if (IS_ERR(local->wep_tx_tfm))
- return -ENOMEM;
+ return PTR_ERR(local->wep_tx_tfm);
local->wep_rx_tfm = crypto_alloc_blkcipher("ecb(arc4)", 0,
CRYPTO_ALG_ASYNC);
if (IS_ERR(local->wep_rx_tfm)) {
crypto_free_blkcipher(local->wep_tx_tfm);
- return -ENOMEM;
+ return PTR_ERR(local->wep_rx_tfm);
}
return 0;
{
int i;
+ /* XXX: currently broken due to cb/requeue use */
+ return -EPERM;
+
/* prepare the filter and save it for the SW queue
* matching the received HW queue */
} else {
struct netdev_queue *txq;
spinlock_t *root_lock;
+ struct Qdisc *q;
txq = netdev_get_tx_queue(local->mdev, agg_queue);
- root_lock = qdisc_root_lock(txq->qdisc);
+ q = rcu_dereference(txq->qdisc);
+ root_lock = qdisc_lock(q);
spin_lock_bh(root_lock);
- qdisc_reset(txq->qdisc);
+ qdisc_reset(q);
spin_unlock_bh(root_lock);
}
}
nf_ct_free_hashtable(nf_conntrack_hash, nf_conntrack_vmalloc,
nf_conntrack_htable_size);
- nf_conntrack_proto_fini();
- nf_conntrack_helper_fini();
- nf_conntrack_expect_fini();
nf_conntrack_acct_fini();
+ nf_conntrack_expect_fini();
+ nf_conntrack_helper_fini();
+ nf_conntrack_proto_fini();
}
struct hlist_head *nf_ct_alloc_hashtable(unsigned int *sizep, int *vmalloced)
/* RFC1122 says the R2 limit should be at least 100 seconds.
Linux uses 15 packets as limit, which corresponds
to ~13-30min depending on RTO. */
-static unsigned int nf_ct_tcp_timeout_max_retrans __read_mostly = 5 MINS;
+static unsigned int nf_ct_tcp_timeout_max_retrans __read_mostly = 5 MINS;
+static unsigned int nf_ct_tcp_timeout_unacknowledged __read_mostly = 5 MINS;
static unsigned int tcp_timeouts[TCP_CONNTRACK_MAX] __read_mostly = {
[TCP_CONNTRACK_SYN_SENT] = 2 MINS,
swin = win + (sack - ack);
if (sender->td_maxwin < swin)
sender->td_maxwin = swin;
- if (after(end, sender->td_end))
+ if (after(end, sender->td_end)) {
sender->td_end = end;
+ sender->flags |= IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED;
+ }
/*
* Update receiver data.
*/
if (win == 0)
receiver->td_maxend++;
}
+ if (ack == receiver->td_end)
+ receiver->flags &= ~IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED;
/*
* Check retransmissions.
if (old_state != new_state
&& new_state == TCP_CONNTRACK_FIN_WAIT)
ct->proto.tcp.seen[dir].flags |= IP_CT_TCP_FLAG_CLOSE_INIT;
- timeout = ct->proto.tcp.retrans >= nf_ct_tcp_max_retrans
- && tcp_timeouts[new_state] > nf_ct_tcp_timeout_max_retrans
- ? nf_ct_tcp_timeout_max_retrans : tcp_timeouts[new_state];
+
+ if (ct->proto.tcp.retrans >= nf_ct_tcp_max_retrans &&
+ tcp_timeouts[new_state] > nf_ct_tcp_timeout_max_retrans)
+ timeout = nf_ct_tcp_timeout_max_retrans;
+ else if ((ct->proto.tcp.seen[0].flags | ct->proto.tcp.seen[1].flags) &
+ IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED &&
+ tcp_timeouts[new_state] > nf_ct_tcp_timeout_unacknowledged)
+ timeout = nf_ct_tcp_timeout_unacknowledged;
+ else
+ timeout = tcp_timeouts[new_state];
write_unlock_bh(&tcp_lock);
nf_conntrack_event_cache(IPCT_PROTOINFO_VOLATILE, skb);
.mode = 0644,
.proc_handler = &proc_dointvec_jiffies,
},
+ {
+ .procname = "nf_conntrack_tcp_timeout_unacknowledged",
+ .data = &nf_ct_tcp_timeout_unacknowledged,
+ .maxlen = sizeof(unsigned int),
+ .mode = 0644,
+ .proc_handler = &proc_dointvec_jiffies,
+ },
{
.ctl_name = NET_NF_CONNTRACK_TCP_LOOSE,
.procname = "nf_conntrack_tcp_loose",
static int log_invalid_proto_max = 255;
static struct ctl_table_header *nf_ct_sysctl_header;
+static struct ctl_table_header *nf_ct_netfilter_header;
static ctl_table nf_ct_sysctl_table[] = {
{
#define NET_NF_CONNTRACK_MAX 2089
static ctl_table nf_ct_netfilter_table[] = {
- {
- .ctl_name = NET_NETFILTER,
- .procname = "netfilter",
- .mode = 0555,
- .child = nf_ct_sysctl_table,
- },
{
.ctl_name = NET_NF_CONNTRACK_MAX,
.procname = "nf_conntrack_max",
static int nf_conntrack_standalone_init_sysctl(void)
{
- nf_ct_sysctl_header =
+ nf_ct_netfilter_header =
register_sysctl_paths(nf_ct_path, nf_ct_netfilter_table);
- if (nf_ct_sysctl_header == NULL) {
- printk("nf_conntrack: can't register to sysctl.\n");
- return -ENOMEM;
- }
+ if (!nf_ct_netfilter_header)
+ goto out;
+
+ nf_ct_sysctl_header =
+ register_sysctl_paths(nf_net_netfilter_sysctl_path,
+ nf_ct_sysctl_table);
+ if (!nf_ct_sysctl_header)
+ goto out_unregister_netfilter;
+
return 0;
+out_unregister_netfilter:
+ unregister_sysctl_table(nf_ct_netfilter_header);
+out:
+ printk("nf_conntrack: can't register to sysctl.\n");
+ return -ENOMEM;
}
static void nf_conntrack_standalone_fini_sysctl(void)
{
+ unregister_sysctl_table(nf_ct_netfilter_header);
unregister_sysctl_table(nf_ct_sysctl_header);
}
#else
static void htable_destroy(struct xt_hashlimit_htable *hinfo)
{
- /* remove timer, if it is pending */
- if (timer_pending(&hinfo->timer))
- del_timer(&hinfo->timer);
+ del_timer_sync(&hinfo->timer);
/* remove proc entry */
remove_proc_entry(hinfo->pde->name,
static DEFINE_RFKILL_TASK(rfkill_wimax, RFKILL_TYPE_WIMAX);
static DEFINE_RFKILL_TASK(rfkill_wwan, RFKILL_TYPE_WWAN);
+static void rfkill_schedule_evsw_rfkillall(int state)
+{
+ /* EVERY radio type. state != 0 means radios ON */
+ /* handle EPO (emergency power off) through shortcut */
+ if (state) {
+ rfkill_schedule_set(&rfkill_wwan,
+ RFKILL_STATE_UNBLOCKED);
+ rfkill_schedule_set(&rfkill_wimax,
+ RFKILL_STATE_UNBLOCKED);
+ rfkill_schedule_set(&rfkill_uwb,
+ RFKILL_STATE_UNBLOCKED);
+ rfkill_schedule_set(&rfkill_bt,
+ RFKILL_STATE_UNBLOCKED);
+ rfkill_schedule_set(&rfkill_wlan,
+ RFKILL_STATE_UNBLOCKED);
+ } else
+ rfkill_schedule_epo();
+}
+
static void rfkill_event(struct input_handle *handle, unsigned int type,
unsigned int code, int data)
{
} else if (type == EV_SW) {
switch (code) {
case SW_RFKILL_ALL:
- /* EVERY radio type. data != 0 means radios ON */
- /* handle EPO (emergency power off) through shortcut */
- if (data) {
- rfkill_schedule_set(&rfkill_wwan,
- RFKILL_STATE_UNBLOCKED);
- rfkill_schedule_set(&rfkill_wimax,
- RFKILL_STATE_UNBLOCKED);
- rfkill_schedule_set(&rfkill_uwb,
- RFKILL_STATE_UNBLOCKED);
- rfkill_schedule_set(&rfkill_bt,
- RFKILL_STATE_UNBLOCKED);
- rfkill_schedule_set(&rfkill_wlan,
- RFKILL_STATE_UNBLOCKED);
- } else
- rfkill_schedule_epo();
+ rfkill_schedule_evsw_rfkillall(data);
break;
default:
break;
handle->handler = handler;
handle->name = "rfkill";
+ /* causes rfkill_start() to be called */
error = input_register_handle(handle);
if (error)
goto err_free_handle;
return error;
}
+static void rfkill_start(struct input_handle *handle)
+{
+ /* Take event_lock to guard against configuration changes, we
+ * should be able to deal with concurrency with rfkill_event()
+ * just fine (which event_lock will also avoid). */
+ spin_lock_irq(&handle->dev->event_lock);
+
+ if (test_bit(EV_SW, handle->dev->evbit)) {
+ if (test_bit(SW_RFKILL_ALL, handle->dev->swbit))
+ rfkill_schedule_evsw_rfkillall(test_bit(SW_RFKILL_ALL,
+ handle->dev->sw));
+ /* add resync for further EV_SW events here */
+ }
+
+ spin_unlock_irq(&handle->dev->event_lock);
+}
+
static void rfkill_disconnect(struct input_handle *handle)
{
input_close_device(handle);
.event = rfkill_event,
.connect = rfkill_connect,
.disconnect = rfkill_disconnect,
+ .start = rfkill_start,
.name = "rfkill",
.id_table = rfkill_ids,
};
#endif /* CONFIG_RFKILL_LEDS */
}
+#ifdef CONFIG_RFKILL_LEDS
+static void rfkill_led_trigger_activate(struct led_classdev *led)
+{
+ struct rfkill *rfkill = container_of(led->trigger,
+ struct rfkill, led_trigger);
+
+ rfkill_led_trigger(rfkill, rfkill->state);
+}
+#endif /* CONFIG_RFKILL_LEDS */
+
static void notify_rfkill_state_change(struct rfkill *rfkill)
{
blocking_notifier_call_chain(&rfkill_notifier_list,
/**
* rfkill_toggle_radio - wrapper for toggle_radio hook
- *
* @rfkill: the rfkill struct to use
* @force: calls toggle_radio even if cache says it is not needed,
* and also makes sure notifications of the state will be
* calls and handling all the red tape such as issuing notifications
* if the call is successful.
*
- * Note that @force cannot override a (possibly cached) state of
- * RFKILL_STATE_HARD_BLOCKED. Any device making use of
+ * Note that the @force parameter cannot override a (possibly cached)
+ * state of RFKILL_STATE_HARD_BLOCKED. Any device making use of
* RFKILL_STATE_HARD_BLOCKED implements either get_state() or
* rfkill_force_state(), so the cache either is bypassed or valid.
*
* even if the radio is in RFKILL_STATE_HARD_BLOCKED state, so as to
* give the driver a hint that it should double-BLOCK the transmitter.
*
- * Caller must have aquired rfkill_mutex.
+ * Caller must have acquired rfkill->mutex.
*/
static int rfkill_toggle_radio(struct rfkill *rfkill,
enum rfkill_state state,
/**
* rfkill_switch_all - Toggle state of all switches of given type
- * @type: type of interfaces to be affeceted
+ * @type: type of interfaces to be affected
* @state: the new state
*
- * This function toggles state of all switches of given type unless
- * a specific switch is claimed by userspace in which case it is
- * left alone.
+ * This function toggles the state of all switches of given type,
+ * unless a specific switch is claimed by userspace (in which case,
+ * that switch is left alone).
*/
void rfkill_switch_all(enum rfkill_type type, enum rfkill_state state)
{
rfkill_states[type] = state;
list_for_each_entry(rfkill, &rfkill_list, node) {
- if ((!rfkill->user_claim) && (rfkill->type == type))
+ if ((!rfkill->user_claim) && (rfkill->type == type)) {
+ mutex_lock(&rfkill->mutex);
rfkill_toggle_radio(rfkill, state, 0);
+ mutex_unlock(&rfkill->mutex);
+ }
}
mutex_unlock(&rfkill_mutex);
* rfkill_epo - emergency power off all transmitters
*
* This kicks all rfkill devices to RFKILL_STATE_SOFT_BLOCKED, ignoring
- * everything in its path but rfkill_mutex.
+ * everything in its path but rfkill_mutex and rfkill->mutex.
*/
void rfkill_epo(void)
{
mutex_lock(&rfkill_mutex);
list_for_each_entry(rfkill, &rfkill_list, node) {
+ mutex_lock(&rfkill->mutex);
rfkill_toggle_radio(rfkill, RFKILL_STATE_SOFT_BLOCKED, 1);
+ mutex_unlock(&rfkill->mutex);
}
mutex_unlock(&rfkill_mutex);
}
* a notification by the firmware/hardware of the current *real*
* state of the radio rfkill switch.
*
- * It may not be called from an atomic context.
+ * Devices which are subject to external changes on their rfkill
+ * state (such as those caused by a hardware rfkill line) MUST
+ * have their driver arrange to call rfkill_force_state() as soon
+ * as possible after such a change.
+ *
+ * This function may not be called from an atomic context.
*/
int rfkill_force_state(struct rfkill *rfkill, enum rfkill_state state)
{
if (!capable(CAP_NET_ADMIN))
return -EPERM;
+ if (rfkill->user_claim_unsupported)
+ return -EOPNOTSUPP;
+
/*
* Take the global lock to make sure the kernel is not in
* the middle of rfkill_switch_all
if (error)
return error;
- if (rfkill->user_claim_unsupported) {
- error = -EOPNOTSUPP;
- goto out_unlock;
- }
if (rfkill->user_claim != claim) {
- if (!claim)
+ if (!claim) {
+ mutex_lock(&rfkill->mutex);
rfkill_toggle_radio(rfkill,
rfkill_states[rfkill->type],
0);
+ mutex_unlock(&rfkill->mutex);
+ }
rfkill->user_claim = claim;
}
-out_unlock:
mutex_unlock(&rfkill_mutex);
return error ? error : count;
{
mutex_lock(&rfkill_mutex);
list_del_init(&rfkill->node);
- rfkill_toggle_radio(rfkill, RFKILL_STATE_SOFT_BLOCKED, 1);
mutex_unlock(&rfkill_mutex);
+
+ mutex_lock(&rfkill->mutex);
+ rfkill_toggle_radio(rfkill, RFKILL_STATE_SOFT_BLOCKED, 1);
+ mutex_unlock(&rfkill->mutex);
}
/**
* @type: type of the switch (RFKILL_TYPE_*)
*
* This function should be called by the network driver when it needs
- * rfkill structure. Once the structure is allocated the driver shoud
- * finish its initialization by setting name, private data, enable_radio
+ * rfkill structure. Once the structure is allocated the driver should
+ * finish its initialization by setting the name, private data, enable_radio
* and disable_radio methods and then register it with rfkill_register().
+ *
* NOTE: If registration fails the structure shoudl be freed by calling
* rfkill_free() otherwise rfkill_unregister() should be used.
*/
* rfkill_free - Mark rfkill structure for deletion
* @rfkill: rfkill structure to be destroyed
*
- * Decrements reference count of rfkill structure so it is destroyed.
+ * Decrements reference count of the rfkill structure so it is destroyed.
* Note that rfkill_free() should _not_ be called after rfkill_unregister().
*/
void rfkill_free(struct rfkill *rfkill)
#ifdef CONFIG_RFKILL_LEDS
int error;
- rfkill->led_trigger.name = rfkill->dev.bus_id;
+ if (!rfkill->led_trigger.name)
+ rfkill->led_trigger.name = rfkill->dev.bus_id;
+ if (!rfkill->led_trigger.activate)
+ rfkill->led_trigger.activate = rfkill_led_trigger_activate;
error = led_trigger_register(&rfkill->led_trigger);
if (error)
rfkill->led_trigger.name = NULL;
static void rfkill_led_trigger_unregister(struct rfkill *rfkill)
{
#ifdef CONFIG_RFKILL_LEDS
- if (rfkill->led_trigger.name)
+ if (rfkill->led_trigger.name) {
led_trigger_unregister(&rfkill->led_trigger);
+ rfkill->led_trigger.name = NULL;
+ }
#endif
}
error = device_add(dev);
if (error) {
- rfkill_led_trigger_unregister(rfkill);
rfkill_remove_switch(rfkill);
+ rfkill_led_trigger_unregister(rfkill);
return error;
}
{
struct tcf_common *p = NULL;
if (index && (p = tcf_hash_lookup(index, hinfo)) != NULL) {
- if (bind) {
+ if (bind)
p->tcfc_bindcnt++;
- p->tcfc_refcnt++;
- }
+ p->tcfc_refcnt++;
a->priv = p;
}
return p;
for (i = 0; i < dev->num_tx_queues; i++) {
struct netdev_queue *txq = netdev_get_tx_queue(dev, i);
- struct Qdisc *q, *txq_root = txq->qdisc;
+ struct Qdisc *q, *txq_root = txq->qdisc_sleeping;
if (!(txq_root->flags & TCQ_F_BUILTIN) &&
txq_root->handle == handle)
static struct Qdisc *dev_graft_qdisc(struct netdev_queue *dev_queue,
struct Qdisc *qdisc)
{
+ struct Qdisc *oqdisc = dev_queue->qdisc_sleeping;
spinlock_t *root_lock;
- struct Qdisc *oqdisc;
- int ingress;
-
- ingress = 0;
- if (qdisc && qdisc->flags&TCQ_F_INGRESS)
- ingress = 1;
-
- if (ingress) {
- oqdisc = dev_queue->qdisc;
- } else {
- oqdisc = dev_queue->qdisc_sleeping;
- }
root_lock = qdisc_root_lock(oqdisc);
spin_lock_bh(root_lock);
- if (ingress) {
- /* Prune old scheduler */
- if (oqdisc && atomic_read(&oqdisc->refcnt) <= 1) {
- /* delete */
- qdisc_reset(oqdisc);
- dev_queue->qdisc = NULL;
- } else { /* new */
- dev_queue->qdisc = qdisc;
- }
+ /* Prune old scheduler */
+ if (oqdisc && atomic_read(&oqdisc->refcnt) <= 1)
+ qdisc_reset(oqdisc);
- } else {
- /* Prune old scheduler */
- if (oqdisc && atomic_read(&oqdisc->refcnt) <= 1)
- qdisc_reset(oqdisc);
-
- /* ... and graft new one */
- if (qdisc == NULL)
- qdisc = &noop_qdisc;
- dev_queue->qdisc_sleeping = qdisc;
- dev_queue->qdisc = &noop_qdisc;
- }
+ /* ... and graft new one */
+ if (qdisc == NULL)
+ qdisc = &noop_qdisc;
+ dev_queue->qdisc_sleeping = qdisc;
+ dev_queue->qdisc = &noop_qdisc;
spin_unlock_bh(root_lock);
ingress = 0;
num_q = dev->num_tx_queues;
- if (q && q->flags & TCQ_F_INGRESS) {
+ if ((q && q->flags & TCQ_F_INGRESS) ||
+ (new && new->flags & TCQ_F_INGRESS)) {
num_q = 1;
ingress = 1;
}
if (!ingress)
dev_queue = netdev_get_tx_queue(dev, i);
- if (ingress) {
- old = dev_graft_qdisc(dev_queue, q);
- } else {
- old = dev_graft_qdisc(dev_queue, new);
- if (new && i > 0)
- atomic_inc(&new->refcnt);
- }
+ old = dev_graft_qdisc(dev_queue, new);
+ if (new && i > 0)
+ atomic_inc(&new->refcnt);
+
notify_and_destroy(skb, n, classid, old, new);
}
goto err_out3;
}
}
- if (parent)
- list_add_tail(&sch->list, &dev_queue->qdisc->list);
+ if ((parent != TC_H_ROOT) && !(sch->flags & TCQ_F_INGRESS))
+ list_add_tail(&sch->list, &dev_queue->qdisc_sleeping->list);
return sch;
}
q_idx = 0;
dev_queue = netdev_get_tx_queue(dev, 0);
- if (tc_dump_qdisc_root(dev_queue->qdisc, skb, cb, &q_idx, s_q_idx) < 0)
+ if (tc_dump_qdisc_root(dev_queue->qdisc_sleeping, skb, cb, &q_idx, s_q_idx) < 0)
goto done;
dev_queue = &dev->rx_queue;
- if (tc_dump_qdisc_root(dev_queue->qdisc, skb, cb, &q_idx, s_q_idx) < 0)
+ if (tc_dump_qdisc_root(dev_queue->qdisc_sleeping, skb, cb, &q_idx, s_q_idx) < 0)
goto done;
cont:
case TC_ACT_QUEUED:
case TC_ACT_STOLEN:
kfree_skb(skb);
- return NET_XMIT_SUCCESS;
+ return NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
kfree_skb(skb);
goto drop;
ret = qdisc_enqueue(skb, flow->q);
if (ret != 0) {
drop: __maybe_unused
- sch->qstats.drops++;
- if (flow)
- flow->qstats.drops++;
+ if (net_xmit_drop_count(ret)) {
+ sch->qstats.drops++;
+ if (flow)
+ flow->qstats.drops++;
+ }
return ret;
}
sch->bstats.bytes += qdisc_pkt_len(skb);
return 0;
}
tasklet_schedule(&p->task);
- return NET_XMIT_BYPASS;
+ return NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
}
/*
if (!ret) {
sch->q.qlen++;
sch->qstats.requeues++;
- } else {
+ } else if (net_xmit_drop_count(ret)) {
sch->qstats.drops++;
p->link.qstats.drops++;
}
(cl = cbq_class_lookup(q, prio)) != NULL)
return cl;
- *qerr = NET_XMIT_BYPASS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
for (;;) {
int result = 0;
defmap = head->defaults;
switch (result) {
case TC_ACT_QUEUED:
case TC_ACT_STOLEN:
- *qerr = NET_XMIT_SUCCESS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
return NULL;
case TC_ACT_RECLASSIFY:
q->rx_class = cl;
#endif
if (cl == NULL) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
return ret;
}
- sch->qstats.drops++;
- cbq_mark_toplevel(q, cl);
- cl->qstats.drops++;
+ if (net_xmit_drop_count(ret)) {
+ sch->qstats.drops++;
+ cbq_mark_toplevel(q, cl);
+ cl->qstats.drops++;
+ }
return ret;
}
cbq_activate_class(cl);
return 0;
}
- sch->qstats.drops++;
- cl->qstats.drops++;
+ if (net_xmit_drop_count(ret)) {
+ sch->qstats.drops++;
+ cl->qstats.drops++;
+ }
return ret;
}
q->rx_class = NULL;
if (cl && (cl = cbq_reclassify(skb, cl)) != NULL) {
+ int ret;
cbq_mark_toplevel(q, cl);
q->rx_class = cl;
cl->q->__parent = sch;
- if (qdisc_enqueue(skb, cl->q) == 0) {
+ ret = qdisc_enqueue(skb, cl->q);
+ if (ret == NET_XMIT_SUCCESS) {
sch->q.qlen++;
sch->bstats.packets++;
sch->bstats.bytes += qdisc_pkt_len(skb);
cbq_activate_class(cl);
return 0;
}
- sch->qstats.drops++;
+ if (net_xmit_drop_count(ret))
+ sch->qstats.drops++;
return 0;
}
case TC_ACT_QUEUED:
case TC_ACT_STOLEN:
kfree_skb(skb);
- return NET_XMIT_SUCCESS;
+ return NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
goto drop;
err = qdisc_enqueue(skb, p->q);
if (err != NET_XMIT_SUCCESS) {
- sch->qstats.drops++;
+ if (net_xmit_drop_count(err))
+ sch->qstats.drops++;
return err;
}
drop:
kfree_skb(skb);
sch->qstats.drops++;
- return NET_XMIT_BYPASS;
+ return NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
}
static struct sk_buff *dsmark_dequeue(struct Qdisc *sch)
err = p->q->ops->requeue(skb, p->q);
if (err != NET_XMIT_SUCCESS) {
- sch->qstats.drops++;
+ if (net_xmit_drop_count(err))
+ sch->qstats.drops++;
return err;
}
/* Main transmission queue. */
/* Modifications to data participating in scheduling must be protected with
- * qdisc_root_lock(qdisc) spinlock.
+ * qdisc_lock(qdisc) spinlock.
*
* The idea is the following:
* - enqueue, dequeue are serialized via qdisc root lock
if (unlikely((skb = dequeue_skb(q)) == NULL))
return 0;
- root_lock = qdisc_root_lock(q);
+ root_lock = qdisc_lock(q);
/* And release qdisc */
spin_unlock(root_lock);
txq = netdev_get_tx_queue(dev, skb_get_queue_mapping(skb));
HARD_TX_LOCK(dev, txq, smp_processor_id());
- if (!netif_subqueue_stopped(dev, skb))
+ if (!netif_tx_queue_stopped(txq) &&
+ !netif_tx_queue_frozen(txq))
ret = dev_hard_start_xmit(skb, dev, txq);
HARD_TX_UNLOCK(dev, txq);
break;
}
- if (ret && netif_tx_queue_stopped(txq))
+ if (ret && (netif_tx_queue_stopped(txq) ||
+ netif_tx_queue_frozen(txq)))
ret = 0;
return ret;
}
EXPORT_SYMBOL(qdisc_create_dflt);
-/* Under qdisc_root_lock(qdisc) and BH! */
+/* Under qdisc_lock(qdisc) and BH! */
void qdisc_reset(struct Qdisc *qdisc)
{
kfree((char *) qdisc - qdisc->padded);
}
-/* Under qdisc_root_lock(qdisc) and BH! */
+/* Under qdisc_lock(qdisc) and BH! */
void qdisc_destroy(struct Qdisc *qdisc)
{
int *need_watchdog_p = _need_watchdog;
rcu_assign_pointer(dev_queue->qdisc, new_qdisc);
- if (new_qdisc != &noqueue_qdisc)
+ if (need_watchdog_p && new_qdisc != &noqueue_qdisc)
*need_watchdog_p = 1;
}
need_watchdog = 0;
netdev_for_each_tx_queue(dev, transition_one_qdisc, &need_watchdog);
+ transition_one_qdisc(dev, &dev->rx_queue, NULL);
if (need_watchdog) {
dev->trans_start = jiffies;
dev_queue = netdev_get_tx_queue(dev, i);
q = dev_queue->qdisc;
- root_lock = qdisc_root_lock(q);
+ root_lock = qdisc_lock(q);
if (lock)
spin_lock_bh(root_lock);
bool running;
netdev_for_each_tx_queue(dev, dev_deactivate_queue, &noop_qdisc);
+ dev_deactivate_queue(dev, &dev->rx_queue, &noop_qdisc);
dev_watchdog_down(dev);
void dev_init_scheduler(struct net_device *dev)
{
netdev_for_each_tx_queue(dev, dev_init_scheduler_queue, &noop_qdisc);
- dev_init_scheduler_queue(dev, &dev->rx_queue, NULL);
+ dev_init_scheduler_queue(dev, &dev->rx_queue, &noop_qdisc);
setup_timer(&dev->watchdog_timer, dev_watchdog, (unsigned long)dev);
}
struct Qdisc *qdisc_default = _qdisc_default;
if (qdisc) {
- spinlock_t *root_lock = qdisc_root_lock(qdisc);
+ spinlock_t *root_lock = qdisc_lock(qdisc);
dev_queue->qdisc = qdisc_default;
dev_queue->qdisc_sleeping = qdisc_default;
void dev_shutdown(struct net_device *dev)
{
netdev_for_each_tx_queue(dev, shutdown_scheduler_queue, &noop_qdisc);
- shutdown_scheduler_queue(dev, &dev->rx_queue, NULL);
+ shutdown_scheduler_queue(dev, &dev->rx_queue, &noop_qdisc);
WARN_ON(timer_pending(&dev->watchdog_timer));
}
if (cl->level == 0)
return cl;
- *qerr = NET_XMIT_BYPASS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
tcf = q->root.filter_list;
while (tcf && (result = tc_classify(skb, tcf, &res)) >= 0) {
#ifdef CONFIG_NET_CLS_ACT
switch (result) {
case TC_ACT_QUEUED:
case TC_ACT_STOLEN:
- *qerr = NET_XMIT_SUCCESS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
return NULL;
}
cl = hfsc_classify(skb, sch, &err);
if (cl == NULL) {
- if (err == NET_XMIT_BYPASS)
+ if (err & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return err;
err = qdisc_enqueue(skb, cl->qdisc);
if (unlikely(err != NET_XMIT_SUCCESS)) {
- cl->qstats.drops++;
- sch->qstats.drops++;
+ if (net_xmit_drop_count(err)) {
+ cl->qstats.drops++;
+ sch->qstats.drops++;
+ }
return err;
}
if ((cl = htb_find(skb->priority, sch)) != NULL && cl->level == 0)
return cl;
- *qerr = NET_XMIT_BYPASS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
tcf = q->filter_list;
while (tcf && (result = tc_classify(skb, tcf, &res)) >= 0) {
#ifdef CONFIG_NET_CLS_ACT
switch (result) {
case TC_ACT_QUEUED:
case TC_ACT_STOLEN:
- *qerr = NET_XMIT_SUCCESS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
return NULL;
}
}
#ifdef CONFIG_NET_CLS_ACT
} else if (!cl) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
#endif
- } else if (qdisc_enqueue(skb, cl->un.leaf.q) != NET_XMIT_SUCCESS) {
- sch->qstats.drops++;
- cl->qstats.drops++;
+ } else if ((ret = qdisc_enqueue(skb, cl->un.leaf.q)) != NET_XMIT_SUCCESS) {
+ if (net_xmit_drop_count(ret)) {
+ sch->qstats.drops++;
+ cl->qstats.drops++;
+ }
return NET_XMIT_DROP;
} else {
cl->bstats.packets +=
}
#ifdef CONFIG_NET_CLS_ACT
} else if (!cl) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
#endif
- } else if (cl->un.leaf.q->ops->requeue(skb, cl->un.leaf.q) !=
+ } else if ((ret = cl->un.leaf.q->ops->requeue(skb, cl->un.leaf.q)) !=
NET_XMIT_SUCCESS) {
- sch->qstats.drops++;
- cl->qstats.drops++;
+ if (net_xmit_drop_count(ret)) {
+ sch->qstats.drops++;
+ cl->qstats.drops++;
+ }
return NET_XMIT_DROP;
} else
htb_activate(q, cl);
if (count == 0) {
sch->qstats.drops++;
kfree_skb(skb);
- return NET_XMIT_BYPASS;
+ return NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
}
skb_orphan(skb);
sch->q.qlen++;
sch->bstats.bytes += qdisc_pkt_len(skb);
sch->bstats.packets++;
- } else
+ } else if (net_xmit_drop_count(ret)) {
sch->qstats.drops++;
+ }
pr_debug("netem: enqueue ret %d\n", ret);
return ret;
struct tcf_result res;
int err;
- *qerr = NET_XMIT_BYPASS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
if (TC_H_MAJ(skb->priority) != sch->handle) {
err = tc_classify(skb, q->filter_list, &res);
#ifdef CONFIG_NET_CLS_ACT
switch (err) {
case TC_ACT_STOLEN:
case TC_ACT_QUEUED:
- *qerr = NET_XMIT_SUCCESS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
return NULL;
}
#ifdef CONFIG_NET_CLS_ACT
if (qdisc == NULL) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
sch->q.qlen++;
return NET_XMIT_SUCCESS;
}
- sch->qstats.drops++;
+ if (net_xmit_drop_count(ret))
+ sch->qstats.drops++;
return ret;
}
qdisc = prio_classify(skb, sch, &ret);
#ifdef CONFIG_NET_CLS_ACT
if (qdisc == NULL) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
sch->qstats.requeues++;
return 0;
}
- sch->qstats.drops++;
+ if (net_xmit_drop_count(ret))
+ sch->qstats.drops++;
return NET_XMIT_DROP;
}
sch->bstats.bytes += qdisc_pkt_len(skb);
sch->bstats.packets++;
sch->q.qlen++;
- } else {
+ } else if (net_xmit_drop_count(ret)) {
q->stats.pdrop++;
sch->qstats.drops++;
}
if (!q->filter_list)
return sfq_hash(q, skb) + 1;
- *qerr = NET_XMIT_BYPASS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_BYPASS;
result = tc_classify(skb, q->filter_list, &res);
if (result >= 0) {
#ifdef CONFIG_NET_CLS_ACT
switch (result) {
case TC_ACT_STOLEN:
case TC_ACT_QUEUED:
- *qerr = NET_XMIT_SUCCESS;
+ *qerr = NET_XMIT_SUCCESS | __NET_XMIT_STOLEN;
case TC_ACT_SHOT:
return 0;
}
hash = sfq_classify(skb, sch, &ret);
if (hash == 0) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
hash = sfq_classify(skb, sch, &ret);
if (hash == 0) {
- if (ret == NET_XMIT_BYPASS)
+ if (ret & __NET_XMIT_BYPASS)
sch->qstats.drops++;
kfree_skb(skb);
return ret;
ret = qdisc_enqueue(skb, q->qdisc);
if (ret != 0) {
- sch->qstats.drops++;
+ if (net_xmit_drop_count(ret))
+ sch->qstats.drops++;
return ret;
}
switch (teql_resolve(skb, skb_res, slave)) {
case 0:
- if (netif_tx_trylock(slave)) {
- if (!__netif_subqueue_stopped(slave, subq) &&
+ if (__netif_tx_trylock(slave_txq)) {
+ if (!netif_tx_queue_stopped(slave_txq) &&
+ !netif_tx_queue_frozen(slave_txq) &&
slave->hard_start_xmit(skb, slave) == 0) {
- netif_tx_unlock(slave);
+ __netif_tx_unlock(slave_txq);
master->slaves = NEXT_SLAVE(q);
netif_wake_queue(dev);
master->stats.tx_packets++;
qdisc_pkt_len(skb);
return 0;
}
- netif_tx_unlock(slave);
+ __netif_tx_unlock(slave_txq);
}
if (netif_queue_stopped(dev))
busy = 1;
}
/* Based on tcp_v6_xmit() in tcp_ipv6.c. */
-static int sctp_v6_xmit(struct sk_buff *skb, struct sctp_transport *transport,
- int ipfragok)
+static int sctp_v6_xmit(struct sk_buff *skb, struct sctp_transport *transport)
{
struct sock *sk = skb->sk;
struct ipv6_pinfo *np = inet6_sk(sk);
SCTP_INC_STATS(SCTP_MIB_OUTSCTPPACKS);
- return ip6_xmit(sk, skb, &fl, np->opt, ipfragok);
+ if (!(transport->param_flags & SPP_PMTUD_ENABLE))
+ skb->local_df = 1;
+
+ return ip6_xmit(sk, skb, &fl, np->opt, 0);
}
/* Returns the dst cache entry for the given source and destination ip
SCTP_DEBUG_PRINTK("***sctp_transmit_packet*** skb len %d\n",
nskb->len);
- if (tp->param_flags & SPP_PMTUD_ENABLE)
- (*tp->af_specific->sctp_xmit)(nskb, tp, packet->ipfragok);
- else
- (*tp->af_specific->sctp_xmit)(nskb, tp, 1);
+ nskb->local_df = packet->ipfragok;
+ (*tp->af_specific->sctp_xmit)(nskb, tp);
out:
packet->size = packet->overhead;
/* Wrapper routine that calls the ip transmit routine. */
static inline int sctp_v4_xmit(struct sk_buff *skb,
- struct sctp_transport *transport, int ipfragok)
+ struct sctp_transport *transport)
{
+ struct inet_sock *inet = inet_sk(skb->sk);
+
SCTP_DEBUG_PRINTK("%s: skb:%p, len:%d, "
"src:%u.%u.%u.%u, dst:%u.%u.%u.%u\n",
__func__, skb, skb->len,
NIPQUAD(skb->rtable->rt_src),
NIPQUAD(skb->rtable->rt_dst));
+ inet->pmtudisc = transport->param_flags & SPP_PMTUD_ENABLE ?
+ IP_PMTUDISC_DO : IP_PMTUDISC_DONT;
+
SCTP_INC_STATS(SCTP_MIB_OUTSCTPPACKS);
- return ip_queue_xmit(skb, ipfragok);
+ return ip_queue_xmit(skb, 0);
}
static struct sctp_af sctp_af_inet;
#include <linux/vmalloc.h> /* vmalloc, vfree */
#include <asm/uaccess.h> /* copy_to/from_user */
#include <linux/init.h> /* __initfunc et al. */
-#include <net/syncppp.h>
#define KMEM_SAFETYZONE 8
{
wanif_conf_t *cnf;
struct net_device *dev = NULL;
-#ifdef CONFIG_WANPIPE_MULTPPP
- struct ppp_device *pppdev=NULL;
-#endif
int err;
if ((wandev->state == WAN_UNCONFIGURED) || (wandev->new_if == NULL))
goto out;
if (cnf->config_id == WANCONFIG_MPPP) {
-#ifdef CONFIG_WANPIPE_MULTPPP
- pppdev = kzalloc(sizeof(struct ppp_device), GFP_KERNEL);
- err = -ENOBUFS;
- if (pppdev == NULL)
- goto out;
- pppdev->dev = kzalloc(sizeof(struct net_device), GFP_KERNEL);
- if (pppdev->dev == NULL) {
- kfree(pppdev);
- err = -ENOBUFS;
- goto out;
- }
- err = wandev->new_if(wandev, (struct net_device *)pppdev, cnf);
- dev = pppdev->dev;
-#else
printk(KERN_INFO "%s: Wanpipe Mulit-Port PPP support has not been compiled in!\n",
wandev->name);
err = -EPROTONOSUPPORT;
goto out;
-#endif
} else {
dev = kzalloc(sizeof(struct net_device), GFP_KERNEL);
err = -ENOBUFS;
kfree(dev->priv);
dev->priv = NULL;
-#ifdef CONFIG_WANPIPE_MULTPPP
- if (cnf->config_id == WANCONFIG_MPPP)
- kfree(pppdev);
- else
- kfree(dev);
-#else
/* Sync PPP is disabled */
if (cnf->config_id != WANCONFIG_MPPP)
kfree(dev);
-#endif
-
out:
kfree(cnf);
return err;
};
/* internal helper: get drv and dev */
-static int get_drv_dev_by_info_ifindex(struct genl_info *info,
+static int get_drv_dev_by_info_ifindex(struct nlattr **attrs,
struct cfg80211_registered_device **drv,
struct net_device **dev)
{
int ifindex;
- if (!info->attrs[NL80211_ATTR_IFINDEX])
+ if (!attrs[NL80211_ATTR_IFINDEX])
return -EINVAL;
- ifindex = nla_get_u32(info->attrs[NL80211_ATTR_IFINDEX]);
+ ifindex = nla_get_u32(attrs[NL80211_ATTR_IFINDEX]);
*dev = dev_get_by_index(&init_net, ifindex);
if (!*dev)
return -ENODEV;
mutex_lock(&cfg80211_drv_mutex);
list_for_each_entry(dev, &cfg80211_drv_list, list) {
- if (++wp_idx < wp_start)
+ if (wp_idx < wp_start) {
+ wp_idx++;
continue;
+ }
if_idx = 0;
mutex_lock(&dev->devlist_mtx);
list_for_each_entry(wdev, &dev->netdev_list, list) {
- if (++if_idx < if_start)
+ if (if_idx < if_start) {
+ if_idx++;
continue;
+ }
if (nl80211_send_iface(skb, NETLINK_CB(cb->skb).pid,
cb->nlh->nlmsg_seq, NLM_F_MULTI,
- wdev->netdev) < 0)
- break;
+ wdev->netdev) < 0) {
+ mutex_unlock(&dev->devlist_mtx);
+ goto out;
+ }
+ if_idx++;
}
mutex_unlock(&dev->devlist_mtx);
+
+ wp_idx++;
}
+ out:
mutex_unlock(&cfg80211_drv_mutex);
cb->args[0] = wp_idx;
struct net_device *netdev;
int err;
- err = get_drv_dev_by_info_ifindex(info, &dev, &netdev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &dev, &netdev);
if (err)
return err;
} else
return -EINVAL;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
ifindex = dev->ifindex;
int ifindex, err;
struct net_device *dev;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
ifindex = dev->ifindex;
if (info->attrs[NL80211_ATTR_MAC])
mac_addr = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
if (!info->attrs[NL80211_ATTR_KEY_DEFAULT])
return -EINVAL;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
return -EINVAL;
}
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
if (info->attrs[NL80211_ATTR_MAC])
mac_addr = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
struct beacon_parameters params;
int haveinfo = 0;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
int err;
struct net_device *dev;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
}
static int nl80211_dump_station(struct sk_buff *skb,
- struct netlink_callback *cb)
+ struct netlink_callback *cb)
{
- int wp_idx = 0;
- int if_idx = 0;
- int sta_idx = cb->args[2];
- int wp_start = cb->args[0];
- int if_start = cb->args[1];
struct station_info sinfo;
struct cfg80211_registered_device *dev;
- struct wireless_dev *wdev;
+ struct net_device *netdev;
u8 mac_addr[ETH_ALEN];
+ int ifidx = cb->args[0];
+ int sta_idx = cb->args[1];
int err;
- int exit = 0;
- /* TODO: filter by device */
- mutex_lock(&cfg80211_drv_mutex);
- list_for_each_entry(dev, &cfg80211_drv_list, list) {
- if (exit)
+ if (!ifidx) {
+ err = nlmsg_parse(cb->nlh, GENL_HDRLEN + nl80211_fam.hdrsize,
+ nl80211_fam.attrbuf, nl80211_fam.maxattr,
+ nl80211_policy);
+ if (err)
+ return err;
+
+ if (!nl80211_fam.attrbuf[NL80211_ATTR_IFINDEX])
+ return -EINVAL;
+
+ ifidx = nla_get_u32(nl80211_fam.attrbuf[NL80211_ATTR_IFINDEX]);
+ if (!ifidx)
+ return -EINVAL;
+ }
+
+ netdev = dev_get_by_index(&init_net, ifidx);
+ if (!netdev)
+ return -ENODEV;
+
+ dev = cfg80211_get_dev_from_ifindex(ifidx);
+ if (IS_ERR(dev)) {
+ err = PTR_ERR(dev);
+ goto out_put_netdev;
+ }
+
+ if (!dev->ops->dump_station) {
+ err = -ENOSYS;
+ goto out_err;
+ }
+
+ rtnl_lock();
+
+ while (1) {
+ err = dev->ops->dump_station(&dev->wiphy, netdev, sta_idx,
+ mac_addr, &sinfo);
+ if (err == -ENOENT)
break;
- if (++wp_idx < wp_start)
- continue;
- if_idx = 0;
+ if (err)
+ goto out_err_rtnl;
- mutex_lock(&dev->devlist_mtx);
- list_for_each_entry(wdev, &dev->netdev_list, list) {
- if (exit)
- break;
- if (++if_idx < if_start)
- continue;
- if (!dev->ops->dump_station)
- continue;
+ if (nl80211_send_station(skb,
+ NETLINK_CB(cb->skb).pid,
+ cb->nlh->nlmsg_seq, NLM_F_MULTI,
+ netdev, mac_addr,
+ &sinfo) < 0)
+ goto out;
- for (;; ++sta_idx) {
- rtnl_lock();
- err = dev->ops->dump_station(&dev->wiphy,
- wdev->netdev, sta_idx, mac_addr,
- &sinfo);
- rtnl_unlock();
- if (err) {
- sta_idx = 0;
- break;
- }
- if (nl80211_send_station(skb,
- NETLINK_CB(cb->skb).pid,
- cb->nlh->nlmsg_seq, NLM_F_MULTI,
- wdev->netdev, mac_addr,
- &sinfo) < 0) {
- exit = 1;
- break;
- }
- }
- }
- mutex_unlock(&dev->devlist_mtx);
+ sta_idx++;
}
- mutex_unlock(&cfg80211_drv_mutex);
- cb->args[0] = wp_idx;
- cb->args[1] = if_idx;
- cb->args[2] = sta_idx;
- return skb->len;
+ out:
+ cb->args[1] = sta_idx;
+ err = skb->len;
+ out_err_rtnl:
+ rtnl_unlock();
+ out_err:
+ cfg80211_put_dev(dev);
+ out_put_netdev:
+ dev_put(netdev);
+
+ return err;
}
static int nl80211_get_station(struct sk_buff *skb, struct genl_info *info)
mac_addr = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
params.plink_action =
nla_get_u8(info->attrs[NL80211_ATTR_STA_PLINK_ACTION]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
¶ms.station_flags))
return -EINVAL;
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
if (info->attrs[NL80211_ATTR_MAC])
mac_addr = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
}
static int nl80211_dump_mpath(struct sk_buff *skb,
- struct netlink_callback *cb)
+ struct netlink_callback *cb)
{
- int wp_idx = 0;
- int if_idx = 0;
- int sta_idx = cb->args[2];
- int wp_start = cb->args[0];
- int if_start = cb->args[1];
struct mpath_info pinfo;
struct cfg80211_registered_device *dev;
- struct wireless_dev *wdev;
+ struct net_device *netdev;
u8 dst[ETH_ALEN];
u8 next_hop[ETH_ALEN];
+ int ifidx = cb->args[0];
+ int path_idx = cb->args[1];
int err;
- int exit = 0;
- /* TODO: filter by device */
- mutex_lock(&cfg80211_drv_mutex);
- list_for_each_entry(dev, &cfg80211_drv_list, list) {
- if (exit)
+ if (!ifidx) {
+ err = nlmsg_parse(cb->nlh, GENL_HDRLEN + nl80211_fam.hdrsize,
+ nl80211_fam.attrbuf, nl80211_fam.maxattr,
+ nl80211_policy);
+ if (err)
+ return err;
+
+ if (!nl80211_fam.attrbuf[NL80211_ATTR_IFINDEX])
+ return -EINVAL;
+
+ ifidx = nla_get_u32(nl80211_fam.attrbuf[NL80211_ATTR_IFINDEX]);
+ if (!ifidx)
+ return -EINVAL;
+ }
+
+ netdev = dev_get_by_index(&init_net, ifidx);
+ if (!netdev)
+ return -ENODEV;
+
+ dev = cfg80211_get_dev_from_ifindex(ifidx);
+ if (IS_ERR(dev)) {
+ err = PTR_ERR(dev);
+ goto out_put_netdev;
+ }
+
+ if (!dev->ops->dump_mpath) {
+ err = -ENOSYS;
+ goto out_err;
+ }
+
+ rtnl_lock();
+
+ while (1) {
+ err = dev->ops->dump_mpath(&dev->wiphy, netdev, path_idx,
+ dst, next_hop, &pinfo);
+ if (err == -ENOENT)
break;
- if (++wp_idx < wp_start)
- continue;
- if_idx = 0;
+ if (err)
+ goto out_err_rtnl;
- mutex_lock(&dev->devlist_mtx);
- list_for_each_entry(wdev, &dev->netdev_list, list) {
- if (exit)
- break;
- if (++if_idx < if_start)
- continue;
- if (!dev->ops->dump_mpath)
- continue;
+ if (nl80211_send_mpath(skb, NETLINK_CB(cb->skb).pid,
+ cb->nlh->nlmsg_seq, NLM_F_MULTI,
+ netdev, dst, next_hop,
+ &pinfo) < 0)
+ goto out;
- for (;; ++sta_idx) {
- rtnl_lock();
- err = dev->ops->dump_mpath(&dev->wiphy,
- wdev->netdev, sta_idx, dst,
- next_hop, &pinfo);
- rtnl_unlock();
- if (err) {
- sta_idx = 0;
- break;
- }
- if (nl80211_send_mpath(skb,
- NETLINK_CB(cb->skb).pid,
- cb->nlh->nlmsg_seq, NLM_F_MULTI,
- wdev->netdev, dst, next_hop,
- &pinfo) < 0) {
- exit = 1;
- break;
- }
- }
- }
- mutex_unlock(&dev->devlist_mtx);
+ path_idx++;
}
- mutex_unlock(&cfg80211_drv_mutex);
- cb->args[0] = wp_idx;
- cb->args[1] = if_idx;
- cb->args[2] = sta_idx;
- return skb->len;
+ out:
+ cb->args[1] = path_idx;
+ err = skb->len;
+ out_err_rtnl:
+ rtnl_unlock();
+ out_err:
+ cfg80211_put_dev(dev);
+ out_put_netdev:
+ dev_put(netdev);
+
+ return err;
}
static int nl80211_get_mpath(struct sk_buff *skb, struct genl_info *info)
dst = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
dst = nla_data(info->attrs[NL80211_ATTR_MAC]);
next_hop = nla_data(info->attrs[NL80211_ATTR_MPATH_NEXT_HOP]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
dst = nla_data(info->attrs[NL80211_ATTR_MAC]);
next_hop = nla_data(info->attrs[NL80211_ATTR_MPATH_NEXT_HOP]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
if (info->attrs[NL80211_ATTR_MAC])
dst = nla_data(info->attrs[NL80211_ATTR_MAC]);
- err = get_drv_dev_by_info_ifindex(info, &drv, &dev);
+ err = get_drv_dev_by_info_ifindex(info->attrs, &drv, &dev);
if (err)
return err;
.PHONY: $(PHONY)
__fw_install: $(installed-fw)
+
__fw_modinst: $(installed-mod-fw)
+ @:
+
__fw_modbuild: $(addprefix $(obj)/,$(mod-fw))
+ @:
FORCE:
}
fputs(sym->name, dumpfile);
putc(' ', dumpfile);
+ if (sym->is_extern)
+ fputs("extern ", dumpfile);
print_list(dumpfile, sym->defn);
putc('\n', dumpfile);
/* A lexical scanner generated by flex */
+/* %not-for-header */
+
+/* %if-c-only */
+/* %if-not-reentrant */
+
+/* %endif */
+/* %endif */
+/* %ok-for-header */
+
#define FLEX_SCANNER
#define YY_FLEX_MAJOR_VERSION 2
#define YY_FLEX_MINOR_VERSION 5
-#define YY_FLEX_SUBMINOR_VERSION 33
+#define YY_FLEX_SUBMINOR_VERSION 35
#if YY_FLEX_SUBMINOR_VERSION > 0
#define FLEX_BETA
#endif
/* C99 systems have <inttypes.h>. Non-C99 systems may or may not. */
-#if __STDC_VERSION__ >= 199901L
+#if defined (__STDC_VERSION__) && __STDC_VERSION__ >= 199901L
/* C99 says to define __STDC_LIMIT_MACROS before including stdint.h,
* if you want the limit (max/min) macros for int types.
typedef unsigned char flex_uint8_t;
typedef unsigned short int flex_uint16_t;
typedef unsigned int flex_uint32_t;
-#endif /* ! C99 */
/* Limits of integral types. */
#ifndef INT8_MIN
#define UINT32_MAX (4294967295U)
#endif
+#endif /* ! C99 */
+
#endif /* ! FLEXINT_H */
/* %endif */
#else /* ! __cplusplus */
-#if __STDC__
+/* C99 requires __STDC__ to be defined as 1. */
+#if defined (__STDC__)
#define YY_USE_CONST
-#endif /* __STDC__ */
+#endif /* defined (__STDC__) */
#endif /* ! __cplusplus */
#ifdef YY_USE_CONST
#define unput(c) yyunput( c, (yytext_ptr) )
-/* The following is because we cannot portably get our hands on size_t
- * (without autoconf's help, which isn't available because we want
- * flex-generated scanners to compile on their own).
- */
-
#ifndef YY_TYPEDEF_YY_SIZE_T
#define YY_TYPEDEF_YY_SIZE_T
-typedef unsigned int yy_size_t;
+typedef size_t yy_size_t;
#endif
#ifndef YY_STRUCT_YY_BUFFER_STATE
/* %% [1.0] yytext/yyin/yyout/yy_state_type/yylineno etc. def's & init go here */
/* Begin user sect3 */
-#define yywrap() 1
+#define yywrap(n) 1
#define YY_SKIP_YYWRAP
#define FLEX_DEBUG
static yyconst flex_int16_t yy_rule_linenum[13] =
{ 0,
- 69, 70, 71, 74, 77, 78, 79, 85, 86, 87,
- 89, 92
+ 71, 72, 73, 76, 79, 80, 81, 87, 88, 89,
+ 91, 94
} ;
/* The intent behind this definition is that it'll catch
quite so pedantic. */
/* We don't do multiple input files. */
-#line 669 "scripts/genksyms/lex.c"
+#define YY_NO_INPUT 1
+#line 676 "scripts/genksyms/lex.c"
#define INITIAL 0
#define V2_TOKENS 1
/* %endif */
/* %if-reentrant */
/* %endif */
+/* %endif End reentrant structures and macros. */
+
+/* Accessor methods to globals.
+ These are made visible to non-reentrant scanners for convenience. */
+
+int yylex_destroy (void );
+
+int yyget_debug (void );
+
+void yyset_debug (int debug_flag );
+
+YY_EXTRA_TYPE yyget_extra (void );
+
+void yyset_extra (YY_EXTRA_TYPE user_defined );
+
+FILE *yyget_in (void );
+
+void yyset_in (FILE * in_str );
+
+FILE *yyget_out (void );
+
+void yyset_out (FILE * out_str );
+
+int yyget_leng (void );
+
+char *yyget_text (void );
+
+int yyget_lineno (void );
+
+void yyset_lineno (int line_number );
+
/* %if-bison-bridge */
/* %endif */
-/* %endif End reentrant structures and macros. */
/* Macros after this point can all be overridden by user definitions in
* section 1.
/* This used to be an fputs(), but since the string might contain NUL's,
* we now use fwrite().
*/
-#define ECHO (void) fwrite( yytext, yyleng, 1, yyout )
+#define ECHO fwrite( yytext, yyleng, 1, yyout )
/* %endif */
/* %if-c++-only C++ definition */
/* %endif */
register int yy_act;
/* %% [7.0] user's declarations go here */
-#line 65 "scripts/genksyms/lex.l"
+#line 67 "scripts/genksyms/lex.l"
/* Keep track of our location in the original source files. */
-#line 890 "scripts/genksyms/lex.c"
+#line 927 "scripts/genksyms/lex.c"
if ( !(yy_init) )
{
case 1:
/* rule 1 can match eol */
YY_RULE_SETUP
-#line 69 "scripts/genksyms/lex.l"
+#line 71 "scripts/genksyms/lex.l"
return FILENAME;
YY_BREAK
case 2:
/* rule 2 can match eol */
YY_RULE_SETUP
-#line 70 "scripts/genksyms/lex.l"
+#line 72 "scripts/genksyms/lex.l"
cur_line++;
YY_BREAK
case 3:
/* rule 3 can match eol */
YY_RULE_SETUP
-#line 71 "scripts/genksyms/lex.l"
+#line 73 "scripts/genksyms/lex.l"
cur_line++;
YY_BREAK
/* Ignore all other whitespace. */
case 4:
YY_RULE_SETUP
-#line 74 "scripts/genksyms/lex.l"
+#line 76 "scripts/genksyms/lex.l"
;
YY_BREAK
case 5:
/* rule 5 can match eol */
YY_RULE_SETUP
-#line 77 "scripts/genksyms/lex.l"
+#line 79 "scripts/genksyms/lex.l"
return STRING;
YY_BREAK
case 6:
/* rule 6 can match eol */
YY_RULE_SETUP
-#line 78 "scripts/genksyms/lex.l"
+#line 80 "scripts/genksyms/lex.l"
return CHAR;
YY_BREAK
case 7:
YY_RULE_SETUP
-#line 79 "scripts/genksyms/lex.l"
+#line 81 "scripts/genksyms/lex.l"
return IDENT;
YY_BREAK
/* The Pedant requires that the other C multi-character tokens be
around them properly. */
case 8:
YY_RULE_SETUP
-#line 85 "scripts/genksyms/lex.l"
+#line 87 "scripts/genksyms/lex.l"
return OTHER;
YY_BREAK
case 9:
YY_RULE_SETUP
-#line 86 "scripts/genksyms/lex.l"
+#line 88 "scripts/genksyms/lex.l"
return INT;
YY_BREAK
case 10:
YY_RULE_SETUP
-#line 87 "scripts/genksyms/lex.l"
+#line 89 "scripts/genksyms/lex.l"
return REAL;
YY_BREAK
case 11:
YY_RULE_SETUP
-#line 89 "scripts/genksyms/lex.l"
+#line 91 "scripts/genksyms/lex.l"
return DOTS;
YY_BREAK
/* All other tokens are single characters. */
case 12:
YY_RULE_SETUP
-#line 92 "scripts/genksyms/lex.l"
+#line 94 "scripts/genksyms/lex.l"
return yytext[0];
YY_BREAK
case 13:
YY_RULE_SETUP
-#line 95 "scripts/genksyms/lex.l"
+#line 97 "scripts/genksyms/lex.l"
ECHO;
YY_BREAK
-#line 1081 "scripts/genksyms/lex.c"
+#line 1118 "scripts/genksyms/lex.c"
case YY_STATE_EOF(INITIAL):
case YY_STATE_EOF(V2_TOKENS):
yyterminate();
else
ret_val = EOB_ACT_CONTINUE_SCAN;
+ if ((yy_size_t) ((yy_n_chars) + number_to_move) > YY_CURRENT_BUFFER_LVALUE->yy_buf_size) {
+ /* Extend the array by 50%, plus the number we really need. */
+ yy_size_t new_size = (yy_n_chars) + number_to_move + ((yy_n_chars) >> 1);
+ YY_CURRENT_BUFFER_LVALUE->yy_ch_buf = (char *) yyrealloc((void *) YY_CURRENT_BUFFER_LVALUE->yy_ch_buf,new_size );
+ if ( ! YY_CURRENT_BUFFER_LVALUE->yy_ch_buf )
+ YY_FATAL_ERROR( "out of dynamic memory in yy_get_next_buffer()" );
+ }
+
(yy_n_chars) += number_to_move;
YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars)] = YY_END_OF_BUFFER_CHAR;
YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars) + 1] = YY_END_OF_BUFFER_CHAR;
(yy_buffer_stack) = (struct yy_buffer_state**)yyalloc
(num_to_alloc * sizeof(struct yy_buffer_state*)
);
-
+ if ( ! (yy_buffer_stack) )
+ YY_FATAL_ERROR( "out of dynamic memory in yyensure_buffer_stack()" );
+
memset((yy_buffer_stack), 0, num_to_alloc * sizeof(struct yy_buffer_state*));
(yy_buffer_stack_max) = num_to_alloc;
((yy_buffer_stack),
num_to_alloc * sizeof(struct yy_buffer_state*)
);
+ if ( ! (yy_buffer_stack) )
+ YY_FATAL_ERROR( "out of dynamic memory in yyensure_buffer_stack()" );
/* zero only the new slots.*/
memset((yy_buffer_stack) + (yy_buffer_stack_max), 0, grow_size * sizeof(struct yy_buffer_state*));
/* %if-reentrant */
/* %if-bison-bridge */
/* %endif */
-/* %endif */
+/* %endif if-c-only */
/* %if-c-only */
static int yy_init_globals (void)
}
/* %endif */
-/* %if-c-or-c++ */
-/* %if-c-only */
+/* %if-c-only SNIP! this currently causes conflicts with the c++ scanner */
/* yylex_destroy is for both reentrant and non-reentrant scanners. */
int yylex_destroy (void)
-/* %endif */
-/* %if-c++-only */
-/* %endif */
{
/* Pop the buffer stack, destroying each element. */
yyfree((yy_buffer_stack) );
(yy_buffer_stack) = NULL;
-/* %if-c++-only */
-/* %endif */
-
-/* %if-c-only */
-
/* Reset the globals. This is important in a non-reentrant scanner so the next time
* yylex() is called, initialization will occur. */
yy_init_globals( );
/* %if-reentrant */
/* %endif */
return 0;
-/* %endif */
}
/* %endif */
/* %ok-for-header */
-#line 95 "scripts/genksyms/lex.l"
+#line 97 "scripts/genksyms/lex.l"
/* We don't do multiple input files. */
%option noyywrap
+%option noinput
+
%%
239, 242, 245, 247, 248, 250, 252, 257, 262, 265,
269, 273, 277, 278, 280, 283, 287, 291, 292, 294,
296, 299, 303, 306, 307, 309, 311, 315, 318, 321,
- 323, 326, 327, 329, 332, 333, 335
+ 323, 326, 327, 330, 333, 334, 336
};
/* YYRHS -- A `-1'-separated list of the rules' RHS. */
-1, -1, 89, -1, 90, -1, 89, 90, -1, 64,
91, 44, -1, 1, 44, -1, -1, 92, -1, 93,
-1, 92, 46, 93, -1, 76, 95, -1, 37, 94,
- -1, 94, -1, 52, 34, -1, -1, 31, -1, 30,
- 44, -1, -1, 30, -1, 29, 47, 37, 49, 44,
- -1
+ -1, 94, -1, 52, 34, -1, -1, 95, 31, -1,
+ 30, 44, -1, -1, 30, -1, 29, 47, 37, 49,
+ 44, -1
};
/* YYRLINE[YYN] -- source line where rule number YYN was defined. */
2, 2, 1, 0, 1, 1, 4, 4, 2, 3,
3, 3, 0, 1, 2, 3, 3, 0, 1, 1,
2, 3, 2, 0, 1, 1, 3, 2, 2, 1,
- 2, 0, 1, 2, 0, 1, 5
+ 2, 0, 2, 2, 0, 1, 5
};
/* YYDEFACT[STATE-NAME] -- Default rule to reduce with in state
0, 66, 125, 101, 121, 71, 0, 7, 112, 106,
76, 77, 0, 0, 0, 121, 75, 0, 114, 115,
119, 105, 0, 110, 124, 0, 36, 0, 73, 72,
- 61, 20, 122, 102, 0, 93, 0, 84, 87, 88,
- 118, 0, 76, 0, 120, 74, 117, 80, 0, 111,
- 0, 35, 126, 0, 21, 103, 70, 94, 56, 0,
+ 61, 20, 102, 0, 93, 0, 84, 87, 88, 118,
+ 0, 76, 0, 120, 74, 117, 80, 0, 111, 0,
+ 35, 126, 122, 0, 21, 103, 70, 94, 56, 0,
93, 90, 92, 69, 83, 0, 82, 81, 0, 0,
116, 104, 0, 95, 0, 91, 98, 0, 85, 89,
79, 78, 100, 99, 0, 0, 97, 96
{
-1, 1, 2, 3, 35, 72, 55, 36, 64, 65,
66, 75, 38, 39, 40, 41, 42, 67, 86, 87,
- 43, 114, 69, 105, 106, 126, 127, 128, 129, 151,
+ 43, 114, 69, 105, 106, 125, 126, 127, 128, 151,
152, 44, 144, 145, 54, 76, 77, 78, 107, 108,
- 109, 110, 123, 45, 94, 46
+ 109, 110, 122, 45, 94, 46
};
/* YYPACT[STATE-NUM] -- Index in YYTABLE of the portion describing
STATE-NUM. */
-#define YYPACT_NINF -135
+#define YYPACT_NINF -134
static const yytype_int16 yypact[] =
{
- -135, 11, -135, 312, -135, -135, 24, -135, -135, -135,
- -135, -135, -23, -135, -2, -135, -135, -135, -135, -135,
- -135, -135, -135, -135, -17, -135, -11, -135, -135, -135,
- -3, 16, 26, -135, -135, -135, -135, 34, 482, -135,
- -135, -135, -135, -135, -135, -135, -135, -135, -135, -135,
- -8, -135, 22, 97, -135, 482, 22, -135, 482, 56,
- -135, -135, 12, 10, 50, 49, -135, 34, -13, 15,
- -135, -135, 482, -135, 47, -25, 51, 145, -135, -135,
- 34, -135, 356, 52, 71, 77, -135, 10, -135, -135,
- 34, -135, -135, -135, 68, -135, 193, -135, -135, -135,
- 48, -135, 6, 93, 37, 68, 18, 85, 84, -135,
- -135, -135, 87, -135, 102, 86, -135, 89, -135, -135,
- -135, -135, -135, 90, 88, 401, 94, 100, 101, -135,
- -135, 99, -135, 108, -135, -135, -135, -135, 230, -135,
- -25, -135, -135, 105, -135, -135, -135, -135, -135, 9,
- 42, -135, 28, -135, -135, 445, -135, -135, 119, 125,
- -135, -135, 126, -135, 128, -135, -135, 267, -135, -135,
- -135, -135, -135, -135, 129, 130, -135, -135
+ -134, 16, -134, 312, -134, -134, 20, -134, -134, -134,
+ -134, -134, -18, -134, -3, -134, -134, -134, -134, -134,
+ -134, -134, -134, -134, -26, -134, -25, -134, -134, -134,
+ -7, 5, 27, -134, -134, -134, -134, 46, 482, -134,
+ -134, -134, -134, -134, -134, -134, -134, -134, -134, -134,
+ -8, -134, 30, 97, -134, 482, 30, -134, 482, 7,
+ -134, -134, 12, 10, 42, 55, -134, 46, -15, 15,
+ -134, -134, 482, -134, 25, 26, 47, 145, -134, -134,
+ 46, -134, 356, 39, 71, 77, -134, 10, -134, -134,
+ 46, -134, -134, -134, -134, -134, 193, -134, -134, -134,
+ 75, -134, 6, 95, 43, -134, 28, 86, 85, -134,
+ -134, -134, 88, -134, 103, 87, -134, 91, -134, -134,
+ -134, -134, -23, 90, 401, 94, 101, 102, -134, -134,
+ 98, -134, 108, -134, -134, 109, -134, 230, -134, 26,
+ -134, -134, -134, 134, -134, -134, -134, -134, -134, 9,
+ 48, -134, 35, -134, -134, 445, -134, -134, 125, 126,
+ -134, -134, 128, -134, 129, -134, -134, 267, -134, -134,
+ -134, -134, -134, -134, 130, 131, -134, -134
};
/* YYPGOTO[NTERM-NUM]. */
static const yytype_int16 yypgoto[] =
{
- -135, -135, 179, -135, -135, -135, -135, -47, -135, -135,
- 91, 0, -58, -37, -135, -135, -135, -73, -135, -135,
- -48, -32, -135, -38, -135, -134, -135, -135, 29, -63,
- -135, -135, -135, -135, -20, -135, -135, 106, -135, -135,
- 45, 95, 82, -135, -135, -135
+ -134, -134, 180, -134, -134, -134, -134, -33, -134, -134,
+ 93, 0, -58, -37, -134, -134, -134, -73, -134, -134,
+ -54, -32, -134, -81, -134, -133, -134, -134, 29, -50,
+ -134, -134, -134, -134, -20, -134, -134, 110, -134, -134,
+ 49, 96, 80, -134, -134, -134
};
/* YYTABLE[YYPACT[STATE-NUM]]. What to do in state STATE-NUM. If
#define YYTABLE_NINF -109
static const yytype_int16 yytable[] =
{
- 82, 70, 104, 37, 159, 68, 57, 131, 79, 49,
- 162, 4, 100, 84, 50, 88, 101, 92, 10, 93,
- 52, 51, 102, 63, 71, 97, 56, 103, 20, 104,
- 85, 104, 73, 175, 53, 91, 81, 29, 125, 120,
- 53, 33, -93, 132, 58, 70, 147, 101, 95, 61,
- 163, 137, 150, 102, 63, 80, 149, 63, -93, 62,
- 63, 166, 96, 59, 133, 138, 135, 104, 47, 48,
- 60, 61, 80, 53, 132, 167, 150, 150, 101, 147,
- 125, 62, 63, 163, 102, 63, 164, 165, 70, 149,
- 63, 98, 99, 83, 89, 90, 111, 125, 74, 122,
- 103, 117, 7, 8, 9, 10, 11, 12, 13, 125,
+ 82, 70, 104, 37, 159, 68, 57, 130, 142, 88,
+ 162, 52, 56, 84, 49, 92, 4, 93, 10, 50,
+ 51, 132, 79, 134, 71, 53, 53, 143, 20, 104,
+ 85, 104, 73, 120, 175, 91, 81, 29, 124, 97,
+ 58, 33, -93, 131, 83, 70, 147, 101, 95, 61,
+ 163, 150, 59, 102, 63, 80, 149, 63, -93, 62,
+ 63, 136, 96, 100, 47, 48, 104, 101, 166, 98,
+ 99, 60, 80, 102, 63, 137, 150, 150, 103, 124,
+ 131, 53, 167, 61, 101, 147, 89, 70, 117, 163,
+ 102, 63, 111, 62, 63, 149, 63, 124, 74, 164,
+ 165, 90, 7, 8, 9, 10, 11, 12, 13, 124,
15, 16, 17, 18, 19, 20, 21, 22, 23, 24,
- 118, 26, 27, 28, 29, 30, 119, 134, 33, 139,
- 140, 98, 92, 142, -22, 141, 154, 146, 34, 161,
- 143, -22, -107, 153, -22, -22, 112, 155, 156, -22,
+ 118, 26, 27, 28, 29, 30, 119, 103, 33, 133,
+ 138, 139, 98, 92, -22, 141, 140, 154, 34, 146,
+ 142, -22, -107, 153, -22, -22, 112, 156, 155, -22,
7, 8, 9, 10, 11, 12, 13, 157, 15, 16,
- 17, 18, 19, 20, 21, 22, 23, 24, 170, 26,
- 27, 28, 29, 30, 171, 172, 33, 173, 176, 177,
- 5, 121, -22, 113, 169, 160, 34, 136, 0, -22,
- -108, 0, -22, -22, 124, 130, 0, -22, 7, 8,
+ 17, 18, 19, 20, 21, 22, 23, 24, 161, 26,
+ 27, 28, 29, 30, 170, 171, 33, 172, 173, 176,
+ 177, 5, -22, 121, 169, 135, 34, 113, 160, -22,
+ -108, 0, -22, -22, 123, 0, 129, -22, 7, 8,
9, 10, 11, 12, 13, 0, 15, 16, 17, 18,
19, 20, 21, 22, 23, 24, 0, 26, 27, 28,
29, 30, 0, 0, 33, 0, 0, 0, 0, -86,
static const yytype_int16 yycheck[] =
{
- 58, 38, 75, 3, 138, 37, 26, 1, 55, 32,
- 1, 0, 37, 1, 37, 63, 41, 30, 8, 32,
- 37, 23, 47, 48, 32, 72, 37, 52, 18, 102,
- 62, 104, 52, 167, 51, 67, 56, 27, 96, 87,
- 51, 31, 33, 37, 47, 82, 37, 41, 33, 37,
- 41, 33, 125, 47, 48, 55, 47, 48, 49, 47,
- 48, 33, 47, 47, 102, 47, 104, 140, 44, 45,
- 44, 37, 72, 51, 37, 47, 149, 150, 41, 37,
- 138, 47, 48, 41, 47, 48, 149, 150, 125, 47,
- 48, 44, 45, 37, 44, 46, 45, 155, 1, 31,
- 52, 49, 5, 6, 7, 8, 9, 10, 11, 167,
+ 58, 38, 75, 3, 137, 37, 26, 1, 31, 63,
+ 1, 37, 37, 1, 32, 30, 0, 32, 8, 37,
+ 23, 102, 55, 104, 32, 51, 51, 50, 18, 102,
+ 62, 104, 52, 87, 167, 67, 56, 27, 96, 72,
+ 47, 31, 33, 37, 37, 82, 37, 41, 33, 37,
+ 41, 124, 47, 47, 48, 55, 47, 48, 49, 47,
+ 48, 33, 47, 37, 44, 45, 139, 41, 33, 44,
+ 45, 44, 72, 47, 48, 47, 149, 150, 52, 137,
+ 37, 51, 47, 37, 41, 37, 44, 124, 49, 41,
+ 47, 48, 45, 47, 48, 47, 48, 155, 1, 149,
+ 150, 46, 5, 6, 7, 8, 9, 10, 11, 167,
13, 14, 15, 16, 17, 18, 19, 20, 21, 22,
- 49, 24, 25, 26, 27, 28, 49, 34, 31, 44,
- 46, 44, 30, 44, 37, 49, 36, 49, 41, 34,
- 50, 44, 45, 49, 47, 48, 1, 46, 49, 52,
+ 49, 24, 25, 26, 27, 28, 49, 52, 31, 34,
+ 44, 46, 44, 30, 37, 44, 49, 36, 41, 49,
+ 31, 44, 45, 49, 47, 48, 1, 49, 46, 52,
5, 6, 7, 8, 9, 10, 11, 49, 13, 14,
- 15, 16, 17, 18, 19, 20, 21, 22, 49, 24,
+ 15, 16, 17, 18, 19, 20, 21, 22, 34, 24,
25, 26, 27, 28, 49, 49, 31, 49, 49, 49,
- 1, 90, 37, 77, 155, 140, 41, 105, -1, 44,
- 45, -1, 47, 48, 1, 100, -1, 52, 5, 6,
+ 49, 1, 37, 90, 155, 105, 41, 77, 139, 44,
+ 45, -1, 47, 48, 1, -1, 100, 52, 5, 6,
7, 8, 9, 10, 11, -1, 13, 14, 15, 16,
17, 18, 19, 20, 21, 22, -1, 24, 25, 26,
27, 28, -1, -1, 31, -1, -1, -1, -1, 36,
46, 74, 30, 32, 97, 33, 47, 60, 44, 45,
37, 41, 47, 52, 70, 76, 77, 91, 92, 93,
94, 45, 1, 90, 74, 48, 49, 49, 49, 49,
- 73, 63, 31, 95, 1, 65, 78, 79, 80, 81,
- 94, 1, 37, 76, 34, 76, 95, 33, 47, 44,
- 46, 49, 44, 50, 85, 86, 49, 37, 41, 47,
+ 73, 63, 95, 1, 65, 78, 79, 80, 81, 94,
+ 1, 37, 76, 34, 76, 95, 33, 47, 44, 46,
+ 49, 44, 31, 50, 85, 86, 49, 37, 41, 47,
70, 82, 83, 49, 36, 46, 49, 49, 1, 78,
93, 34, 1, 41, 82, 82, 33, 47, 36, 81,
49, 49, 49, 49, 1, 78, 49, 49
attribute_opt:
/* empty */ { $$ = NULL; }
- | ATTRIBUTE_PHRASE
+ | attribute_opt ATTRIBUTE_PHRASE
;
asm_definition:
break;
}
- if (conf_get_changed() && conf_write(NULL)) {
+ if (conf_write(NULL)) {
fprintf(stderr, _("\n*** Error during writing of the kernel configuration.\n\n"));
exit(1);
}
continue;
if (def == S_DEF_USER) {
sym = sym_find(line + 9);
- if (!sym) {
- conf_warning("trying to assign nonexistent symbol %s", line + 9);
+ if (!sym)
break;
- }
} else {
sym = sym_lookup(line + 9, 0);
if (sym->type == S_UNKNOWN)
}
if (def == S_DEF_USER) {
sym = sym_find(line + 7);
- if (!sym) {
- conf_warning("trying to assign nonexistent symbol %s", line + 7);
+ if (!sym)
break;
- }
} else {
sym = sym_lookup(line + 7, 0);
if (sym->type == S_UNKNOWN)
/* A lexical scanner generated by flex */
+#define yy_create_buffer zconf_create_buffer
+#define yy_delete_buffer zconf_delete_buffer
+#define yy_flex_debug zconf_flex_debug
+#define yy_init_buffer zconf_init_buffer
+#define yy_flush_buffer zconf_flush_buffer
+#define yy_load_buffer_state zconf_load_buffer_state
+#define yy_switch_to_buffer zconf_switch_to_buffer
+#define yyin zconfin
+#define yyleng zconfleng
+#define yylex zconflex
+#define yylineno zconflineno
+#define yyout zconfout
+#define yyrestart zconfrestart
+#define yytext zconftext
+#define yywrap zconfwrap
+#define yyalloc zconfalloc
+#define yyrealloc zconfrealloc
+#define yyfree zconffree
+
#define FLEX_SCANNER
#define YY_FLEX_MAJOR_VERSION 2
#define YY_FLEX_MINOR_VERSION 5
-#define YY_FLEX_SUBMINOR_VERSION 33
+#define YY_FLEX_SUBMINOR_VERSION 35
#if YY_FLEX_SUBMINOR_VERSION > 0
#define FLEX_BETA
#endif
/* C99 systems have <inttypes.h>. Non-C99 systems may or may not. */
-#if __STDC_VERSION__ >= 199901L
+#if defined (__STDC_VERSION__) && __STDC_VERSION__ >= 199901L
/* C99 says to define __STDC_LIMIT_MACROS before including stdint.h,
* if you want the limit (max/min) macros for int types.
typedef unsigned char flex_uint8_t;
typedef unsigned short int flex_uint16_t;
typedef unsigned int flex_uint32_t;
-#endif /* ! C99 */
/* Limits of integral types. */
#ifndef INT8_MIN
#define UINT32_MAX (4294967295U)
#endif
+#endif /* ! C99 */
+
#endif /* ! FLEXINT_H */
#ifdef __cplusplus
#else /* ! __cplusplus */
-#if __STDC__
+/* C99 requires __STDC__ to be defined as 1. */
+#if defined (__STDC__)
#define YY_USE_CONST
-#endif /* __STDC__ */
+#endif /* defined (__STDC__) */
#endif /* ! __cplusplus */
#ifdef YY_USE_CONST
#define unput(c) yyunput( c, (yytext_ptr) )
-/* The following is because we cannot portably get our hands on size_t
- * (without autoconf's help, which isn't available because we want
- * flex-generated scanners to compile on their own).
- */
-
#ifndef YY_TYPEDEF_YY_SIZE_T
#define YY_TYPEDEF_YY_SIZE_T
-typedef unsigned int yy_size_t;
+typedef size_t yy_size_t;
#endif
#ifndef YY_STRUCT_YY_BUFFER_STATE
/* Begin user sect3 */
-#define zconfwrap() 1
+#define zconfwrap(n) 1
#define YY_SKIP_YYWRAP
typedef unsigned char YY_CHAR;
#define YY_MORE_ADJ 0
#define YY_RESTORE_YY_MORE_OFFSET
char *zconftext;
+#define YY_NO_INPUT 1
/*
* Copyright (C) 2002 Roman Zippel <zippel@linux-m68k.org>
static int yy_init_globals (void );
+/* Accessor methods to globals.
+ These are made visible to non-reentrant scanners for convenience. */
+
+int zconflex_destroy (void );
+
+int zconfget_debug (void );
+
+void zconfset_debug (int debug_flag );
+
+YY_EXTRA_TYPE zconfget_extra (void );
+
+void zconfset_extra (YY_EXTRA_TYPE user_defined );
+
+FILE *zconfget_in (void );
+
+void zconfset_in (FILE * in_str );
+
+FILE *zconfget_out (void );
+
+void zconfset_out (FILE * out_str );
+
+int zconfget_leng (void );
+
+char *zconfget_text (void );
+
+int zconfget_lineno (void );
+
+void zconfset_lineno (int line_number );
+
/* Macros after this point can all be overridden by user definitions in
* section 1.
*/
/* This used to be an fputs(), but since the string might contain NUL's,
* we now use fwrite().
*/
-#define ECHO (void) fwrite( zconftext, zconfleng, 1, zconfout )
+#define ECHO fwrite( zconftext, zconfleng, 1, zconfout )
#endif
/* Gets input and stuffs it into "buf". number of characters read, or YY_NULL,
else
ret_val = EOB_ACT_CONTINUE_SCAN;
+ if ((yy_size_t) ((yy_n_chars) + number_to_move) > YY_CURRENT_BUFFER_LVALUE->yy_buf_size) {
+ /* Extend the array by 50%, plus the number we really need. */
+ yy_size_t new_size = (yy_n_chars) + number_to_move + ((yy_n_chars) >> 1);
+ YY_CURRENT_BUFFER_LVALUE->yy_ch_buf = (char *) zconfrealloc((void *) YY_CURRENT_BUFFER_LVALUE->yy_ch_buf,new_size );
+ if ( ! YY_CURRENT_BUFFER_LVALUE->yy_ch_buf )
+ YY_FATAL_ERROR( "out of dynamic memory in yy_get_next_buffer()" );
+ }
+
(yy_n_chars) += number_to_move;
YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars)] = YY_END_OF_BUFFER_CHAR;
YY_CURRENT_BUFFER_LVALUE->yy_ch_buf[(yy_n_chars) + 1] = YY_END_OF_BUFFER_CHAR;
(yy_buffer_stack) = (struct yy_buffer_state**)zconfalloc
(num_to_alloc * sizeof(struct yy_buffer_state*)
);
-
+ if ( ! (yy_buffer_stack) )
+ YY_FATAL_ERROR( "out of dynamic memory in zconfensure_buffer_stack()" );
+
memset((yy_buffer_stack), 0, num_to_alloc * sizeof(struct yy_buffer_state*));
(yy_buffer_stack_max) = num_to_alloc;
((yy_buffer_stack),
num_to_alloc * sizeof(struct yy_buffer_state*)
);
+ if ( ! (yy_buffer_stack) )
+ YY_FATAL_ERROR( "out of dynamic memory in zconfensure_buffer_stack()" );
/* zero only the new slots.*/
memset((yy_buffer_stack) + (yy_buffer_stack_max), 0, grow_size * sizeof(struct yy_buffer_state*));
%option backup nostdinit noyywrap never-interactive full ecs
%option 8bit backup nodefault perf-report perf-report
+%option noinput
%x COMMAND HELP STRING PARAM
%{
/*
my $members = $3;
# ignore embedded structs or unions
- $members =~ s/{.*?}//g;
+ $members =~ s/{.*}//g;
# ignore members marked private:
$members =~ s/\/\*.*?private:.*?public:.*?\*\///gos;
* marked __initdata will be discarded when the module has been intialized.
* Likewise for modules used built-in the sections marked __exit
* are discarded because __exit marked function are supposed to be called
- * only when a moduel is unloaded which never happes for built-in modules.
+ * only when a module is unloaded which never happens for built-in modules.
* The check_sec_ref() function traverses all relocation records
* to find all references to a section that reference a section that will
* be discarded and warns about it.
if [ $stopvers != "default" ]; then
STOPSUBLEVEL=`echo $stopvers | cut -d. -f3`
STOPEXTRA=`echo $stopvers | cut -d. -f4`
+ STOPFULLVERSION=${stopvers%%.$STOPEXTRA}
#echo "#___STOPSUBLEVEL=/$STOPSUBLEVEL/, STOPEXTRA=/$STOPEXTRA/"
else
STOPSUBLEVEL=9999
do
CURRENTFULLVERSION="$VERSION.$PATCHLEVEL.$SUBLEVEL"
EXTRAVER=
- if [ $stopvers = $CURRENTFULLVERSION ]; then
+ if [ $STOPFULLVERSION = $CURRENTFULLVERSION ]; then
echo "Stopping at $CURRENTFULLVERSION base as requested."
break
fi
# /bin /sbin /usr/bin /usr/sbin /usr/local/bin, but it may
# differ on your system.
#
-PATH=/sbin:/usr/sbin:/bin:/usr/bin:/usr/local/sbin:$PATH
echo 'If some fields are empty or look unusual you may have an old version.'
echo 'Compare to the current minimal requirements in Documentation/Changes.'
echo ' '
int rc;
rc = selinux_get_mnt_opts(sb, &opts);
- if (rc)
+ if (rc) {
+ /* before policy load we may get EINVAL, don't show anything */
+ if (rc == -EINVAL)
+ rc = 0;
return rc;
+ }
selinux_write_opts(m, &opts);
#include <asm/irq.h>
#include <linux/mutex.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/audio.h>
#include "pxa2xx-pcm.h"
#include <sound/pcm_params.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
#include "pxa2xx-pcm.h"
#include <linux/pm.h>
#endif
-#include <asm/hardware.h>
-#include <asm/arch/h3600.h>
+#include <mach/hardware.h>
+#include <mach/h3600.h>
#include <asm/mach-types.h>
#include <asm/dma.h>
{
struct seq_oss_synth *rec;
+ if (dev < 0 || dev >= dp->max_synthdev)
+ return -ENXIO;
+
if (dp->synths[dev].is_midi) {
struct midi_info minf;
snd_seq_oss_midi_make_info(dp, dp->synths[dev].midi_mapped, &minf);
#include <linux/kernel.h>
#include <linux/interrupt.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/dma.h>
#include <asm/io.h>
#include <asm/hardware/iomd.h>
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/hardware/iomd.h>
.text
#include "waveartist.h"
#ifdef CONFIG_ARM
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/mach-types.h>
#endif
#include <sound/info.h>
#include <asm/io.h>
#include <asm/dma.h>
-#include <asm/dreamcast/sysasic.h>
+#include <mach/sysasic.h>
#include "aica.h"
MODULE_AUTHOR("Adrian McMenamin <adrian@mcmen.demon.co.uk>");
#include <sound/soc.h>
#include <sound/soc-dapm.h>
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/portmux.h>
#include "../codecs/wm8510.h"
#include "at32-pcm.h"
#include <sound/pcm_params.h>
#include <sound/soc.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/at91_ssc.h>
+#include <mach/hardware.h>
+#include <mach/at91_ssc.h>
#include "at91-pcm.h"
#ifndef _AT91_PCM_H
#define _AT91_PCM_H
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
struct at91_ssc_periph {
void __iomem *base;
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_ssc.h>
+#include <mach/hardware.h>
+#include <mach/at91_pmc.h>
+#include <mach/at91_ssc.h>
#include "at91-pcm.h"
#include "at91-ssc.h"
#include <sound/soc.h>
#include <sound/soc-dapm.h>
-#include <asm/hardware.h>
-#include <asm/arch/gpio.h>
+#include <mach/hardware.h>
+#include <mach/gpio.h>
#include "../codecs/wm8731.h"
#include "at91-pcm.h"
#include <sound/soc.h>
#include <sound/soc-dapm.h>
-#include <asm/mach-types.h>
#include <asm/dma.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include "../codecs/tlv320aic3x.h"
#include "davinci-pcm.h"
* Since each link descriptor has a 32-bit byte count field, we set
* period_bytes_max to the largest 32-bit number. We also have no maximum
* number of periods.
+ *
+ * Note that we specify SNDRV_PCM_INFO_JOINT_DUPLEX here, but only because a
+ * limitation in the SSI driver requires the sample rates for playback and
+ * capture to be the same.
*/
static const struct snd_pcm_hardware fsl_dma_hardware = {
.info = SNDRV_PCM_INFO_INTERLEAVED |
SNDRV_PCM_INFO_MMAP |
- SNDRV_PCM_INFO_MMAP_VALID,
+ SNDRV_PCM_INFO_MMAP_VALID |
+ SNDRV_PCM_INFO_JOINT_DUPLEX,
.formats = FSLDMA_PCM_FORMATS,
.rates = FSLDMA_PCM_RATES,
.rate_min = 5512,
* fsl_dma_open: open a new substream.
*
* Each substream has its own DMA buffer.
+ *
+ * ALSA divides the DMA buffer into N periods. We create NUM_DMA_LINKS link
+ * descriptors that ping-pong from one period to the next. For example, if
+ * there are six periods and two link descriptors, this is how they look
+ * before playback starts:
+ *
+ * The last link descriptor
+ * ____________ points back to the first
+ * | |
+ * V |
+ * ___ ___ |
+ * | |->| |->|
+ * |___| |___|
+ * | |
+ * | |
+ * V V
+ * _________________________________________
+ * | | | | | | | The DMA buffer is
+ * | | | | | | | divided into 6 parts
+ * |______|______|______|______|______|______|
+ *
+ * and here's how they look after the first period is finished playing:
+ *
+ * ____________
+ * | |
+ * V |
+ * ___ ___ |
+ * | |->| |->|
+ * |___| |___|
+ * | |
+ * |______________
+ * | |
+ * V V
+ * _________________________________________
+ * | | | | | | |
+ * | | | | | | |
+ * |______|______|______|______|______|______|
+ *
+ * The first link descriptor now points to the third period. The DMA
+ * controller is currently playing the second period. When it finishes, it
+ * will jump back to the first descriptor and play the third period.
+ *
+ * There are four reasons we do this:
+ *
+ * 1. The only way to get the DMA controller to automatically restart the
+ * transfer when it gets to the end of the buffer is to use chaining
+ * mode. Basic direct mode doesn't offer that feature.
+ * 2. We need to receive an interrupt at the end of every period. The DMA
+ * controller can generate an interrupt at the end of every link transfer
+ * (aka segment). Making each period into a DMA segment will give us the
+ * interrupts we need.
+ * 3. By creating only two link descriptors, regardless of the number of
+ * periods, we do not need to reallocate the link descriptors if the
+ * number of periods changes.
+ * 4. All of the audio data is still stored in a single, contiguous DMA
+ * buffer, which is what ALSA expects. We're just dividing it into
+ * contiguous parts, and creating a link descriptor for each one.
*/
static int fsl_dma_open(struct snd_pcm_substream *substream)
{
struct snd_pcm_runtime *runtime = substream->runtime;
struct fsl_dma_private *dma_private;
+ struct ccsr_dma_channel __iomem *dma_channel;
dma_addr_t ld_buf_phys;
+ u64 temp_link; /* Pointer to next link descriptor */
+ u32 mr;
unsigned int channel;
int ret = 0;
+ unsigned int i;
/*
* Reject any DMA buffer whose size is not a multiple of the period
snd_soc_set_runtime_hwparams(substream, &fsl_dma_hardware);
runtime->private_data = dma_private;
+ /* Program the fixed DMA controller parameters */
+
+ dma_channel = dma_private->dma_channel;
+
+ temp_link = dma_private->ld_buf_phys +
+ sizeof(struct fsl_dma_link_descriptor);
+
+ for (i = 0; i < NUM_DMA_LINKS; i++) {
+ struct fsl_dma_link_descriptor *link = &dma_private->link[i];
+
+ link->source_attr = cpu_to_be32(CCSR_DMA_ATR_SNOOP);
+ link->dest_attr = cpu_to_be32(CCSR_DMA_ATR_SNOOP);
+ link->next = cpu_to_be64(temp_link);
+
+ temp_link += sizeof(struct fsl_dma_link_descriptor);
+ }
+ /* The last link descriptor points to the first */
+ dma_private->link[i - 1].next = cpu_to_be64(dma_private->ld_buf_phys);
+
+ /* Tell the DMA controller where the first link descriptor is */
+ out_be32(&dma_channel->clndar,
+ CCSR_DMA_CLNDAR_ADDR(dma_private->ld_buf_phys));
+ out_be32(&dma_channel->eclndar,
+ CCSR_DMA_ECLNDAR_ADDR(dma_private->ld_buf_phys));
+
+ /* The manual says the BCR must be clear before enabling EMP */
+ out_be32(&dma_channel->bcr, 0);
+
+ /*
+ * Program the mode register for interrupts, external master control,
+ * and source/destination hold. Also clear the Channel Abort bit.
+ */
+ mr = in_be32(&dma_channel->mr) &
+ ~(CCSR_DMA_MR_CA | CCSR_DMA_MR_DAHE | CCSR_DMA_MR_SAHE);
+
+ /*
+ * We want External Master Start and External Master Pause enabled,
+ * because the SSI is controlling the DMA controller. We want the DMA
+ * controller to be set up in advance, and then we signal only the SSI
+ * to start transferring.
+ *
+ * We want End-Of-Segment Interrupts enabled, because this will generate
+ * an interrupt at the end of each segment (each link descriptor
+ * represents one segment). Each DMA segment is the same thing as an
+ * ALSA period, so this is how we get an interrupt at the end of every
+ * period.
+ *
+ * We want Error Interrupt enabled, so that we can get an error if
+ * the DMA controller is mis-programmed somehow.
+ */
+ mr |= CCSR_DMA_MR_EOSIE | CCSR_DMA_MR_EIE | CCSR_DMA_MR_EMP_EN |
+ CCSR_DMA_MR_EMS_EN;
+
+ /* For playback, we want the destination address to be held. For
+ capture, set the source address to be held. */
+ mr |= (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ?
+ CCSR_DMA_MR_DAHE : CCSR_DMA_MR_SAHE;
+
+ out_be32(&dma_channel->mr, mr);
+
return 0;
}
/**
- * fsl_dma_hw_params: allocate the DMA buffer and the DMA link descriptors.
+ * fsl_dma_hw_params: continue initializing the DMA links
*
- * ALSA divides the DMA buffer into N periods. We create NUM_DMA_LINKS link
- * descriptors that ping-pong from one period to the next. For example, if
- * there are six periods and two link descriptors, this is how they look
- * before playback starts:
- *
- * The last link descriptor
- * ____________ points back to the first
- * | |
- * V |
- * ___ ___ |
- * | |->| |->|
- * |___| |___|
- * | |
- * | |
- * V V
- * _________________________________________
- * | | | | | | | The DMA buffer is
- * | | | | | | | divided into 6 parts
- * |______|______|______|______|______|______|
- *
- * and here's how they look after the first period is finished playing:
- *
- * ____________
- * | |
- * V |
- * ___ ___ |
- * | |->| |->|
- * |___| |___|
- * | |
- * |______________
- * | |
- * V V
- * _________________________________________
- * | | | | | | |
- * | | | | | | |
- * |______|______|______|______|______|______|
- *
- * The first link descriptor now points to the third period. The DMA
- * controller is currently playing the second period. When it finishes, it
- * will jump back to the first descriptor and play the third period.
- *
- * There are four reasons we do this:
- *
- * 1. The only way to get the DMA controller to automatically restart the
- * transfer when it gets to the end of the buffer is to use chaining
- * mode. Basic direct mode doesn't offer that feature.
- * 2. We need to receive an interrupt at the end of every period. The DMA
- * controller can generate an interrupt at the end of every link transfer
- * (aka segment). Making each period into a DMA segment will give us the
- * interrupts we need.
- * 3. By creating only two link descriptors, regardless of the number of
- * periods, we do not need to reallocate the link descriptors if the
- * number of periods changes.
- * 4. All of the audio data is still stored in a single, contiguous DMA
- * buffer, which is what ALSA expects. We're just dividing it into
- * contiguous parts, and creating a link descriptor for each one.
+ * This function obtains hardware parameters about the opened stream and
+ * programs the DMA controller accordingly.
*
* Note that due to a quirk of the SSI's STX register, the target address
* for the DMA operations depends on the sample size. So we don't program
{
struct snd_pcm_runtime *runtime = substream->runtime;
struct fsl_dma_private *dma_private = runtime->private_data;
- struct ccsr_dma_channel __iomem *dma_channel = dma_private->dma_channel;
dma_addr_t temp_addr; /* Pointer to next period */
- u64 temp_link; /* Pointer to next link descriptor */
- u32 mr; /* Temporary variable for MR register */
unsigned int i;
dma_private->dma_buf_next = dma_private->dma_buf_phys;
/*
- * Initialize each link descriptor.
- *
* The actual address in STX0 (destination for playback, source for
* capture) is based on the sample size, but we don't know the sample
* size in this function, so we'll have to adjust that later. See
* buffer itself.
*/
temp_addr = substream->dma_buffer.addr;
- temp_link = dma_private->ld_buf_phys +
- sizeof(struct fsl_dma_link_descriptor);
for (i = 0; i < NUM_DMA_LINKS; i++) {
struct fsl_dma_link_descriptor *link = &dma_private->link[i];
link->count = cpu_to_be32(period_size);
- link->source_attr = cpu_to_be32(CCSR_DMA_ATR_SNOOP);
- link->dest_attr = cpu_to_be32(CCSR_DMA_ATR_SNOOP);
- link->next = cpu_to_be64(temp_link);
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
link->source_addr = cpu_to_be32(temp_addr);
link->dest_addr = cpu_to_be32(temp_addr);
temp_addr += period_size;
- temp_link += sizeof(struct fsl_dma_link_descriptor);
}
- /* The last link descriptor points to the first */
- dma_private->link[i - 1].next = cpu_to_be64(dma_private->ld_buf_phys);
-
- /* Tell the DMA controller where the first link descriptor is */
- out_be32(&dma_channel->clndar,
- CCSR_DMA_CLNDAR_ADDR(dma_private->ld_buf_phys));
- out_be32(&dma_channel->eclndar,
- CCSR_DMA_ECLNDAR_ADDR(dma_private->ld_buf_phys));
-
- /* The manual says the BCR must be clear before enabling EMP */
- out_be32(&dma_channel->bcr, 0);
-
- /*
- * Program the mode register for interrupts, external master control,
- * and source/destination hold. Also clear the Channel Abort bit.
- */
- mr = in_be32(&dma_channel->mr) &
- ~(CCSR_DMA_MR_CA | CCSR_DMA_MR_DAHE | CCSR_DMA_MR_SAHE);
-
- /*
- * We want External Master Start and External Master Pause enabled,
- * because the SSI is controlling the DMA controller. We want the DMA
- * controller to be set up in advance, and then we signal only the SSI
- * to start transfering.
- *
- * We want End-Of-Segment Interrupts enabled, because this will generate
- * an interrupt at the end of each segment (each link descriptor
- * represents one segment). Each DMA segment is the same thing as an
- * ALSA period, so this is how we get an interrupt at the end of every
- * period.
- *
- * We want Error Interrupt enabled, so that we can get an error if
- * the DMA controller is mis-programmed somehow.
- */
- mr |= CCSR_DMA_MR_EOSIE | CCSR_DMA_MR_EIE | CCSR_DMA_MR_EMP_EN |
- CCSR_DMA_MR_EMS_EN;
-
- /* For playback, we want the destination address to be held. For
- capture, set the source address to be held. */
- mr |= (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ?
- CCSR_DMA_MR_DAHE : CCSR_DMA_MR_SAHE;
-
- out_be32(&dma_channel->mr, mr);
return 0;
}
* @ssi: pointer to the SSI's registers
* @ssi_phys: physical address of the SSI registers
* @irq: IRQ of this SSI
+ * @first_stream: pointer to the stream that was opened first
+ * @second_stream: pointer to second stream
* @dev: struct device pointer
* @playback: the number of playback streams opened
* @capture: the number of capture streams opened
struct ccsr_ssi __iomem *ssi;
dma_addr_t ssi_phys;
unsigned int irq;
+ struct snd_pcm_substream *first_stream;
+ struct snd_pcm_substream *second_stream;
struct device *dev;
unsigned int playback;
unsigned int capture;
*/
}
+ if (!ssi_private->first_stream)
+ ssi_private->first_stream = substream;
+ else {
+ /* This is the second stream open, so we need to impose sample
+ * rate and maybe sample size constraints. Note that this can
+ * cause a race condition if the second stream is opened before
+ * the first stream is fully initialized.
+ *
+ * We provide some protection by checking to make sure the first
+ * stream is initialized, but it's not perfect. ALSA sometimes
+ * re-initializes the driver with a different sample rate or
+ * size. If the second stream is opened before the first stream
+ * has received its final parameters, then the second stream may
+ * be constrained to the wrong sample rate or size.
+ *
+ * FIXME: This code does not handle opening and closing streams
+ * repeatedly. If you open two streams and then close the first
+ * one, you may not be able to open another stream until you
+ * close the second one as well.
+ */
+ struct snd_pcm_runtime *first_runtime =
+ ssi_private->first_stream->runtime;
+
+ if (!first_runtime->rate || !first_runtime->sample_bits) {
+ dev_err(substream->pcm->card->dev,
+ "set sample rate and size in %s stream first\n",
+ substream->stream == SNDRV_PCM_STREAM_PLAYBACK
+ ? "capture" : "playback");
+ return -EAGAIN;
+ }
+
+ snd_pcm_hw_constraint_minmax(substream->runtime,
+ SNDRV_PCM_HW_PARAM_RATE,
+ first_runtime->rate, first_runtime->rate);
+
+ snd_pcm_hw_constraint_minmax(substream->runtime,
+ SNDRV_PCM_HW_PARAM_SAMPLE_BITS,
+ first_runtime->sample_bits,
+ first_runtime->sample_bits);
+
+ ssi_private->second_stream = substream;
+ }
+
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
ssi_private->playback++;
struct fsl_ssi_private *ssi_private = rtd->dai->cpu_dai->private_data;
struct ccsr_ssi __iomem *ssi = ssi_private->ssi;
- u32 wl;
- wl = CCSR_SSI_SxCCR_WL(snd_pcm_format_width(runtime->format));
+ if (substream == ssi_private->first_stream) {
+ u32 wl;
- clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ /* The SSI should always be disabled at this points (SSIEN=0) */
+ wl = CCSR_SSI_SxCCR_WL(snd_pcm_format_width(runtime->format));
- if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ /* In synchronous mode, the SSI uses STCCR for capture */
clrsetbits_be32(&ssi->stccr, CCSR_SSI_SxCCR_WL_MASK, wl);
- else
- clrsetbits_be32(&ssi->srccr, CCSR_SSI_SxCCR_WL_MASK, wl);
-
- setbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ }
return 0;
}
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
- setbits32(&ssi->scr, CCSR_SSI_SCR_TE);
+ clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ setbits32(&ssi->scr,
+ CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE);
} else {
- setbits32(&ssi->scr, CCSR_SSI_SCR_RE);
+ clrbits32(&ssi->scr, CCSR_SSI_SCR_SSIEN);
+ setbits32(&ssi->scr,
+ CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE);
/*
* I think we need this delay to allow time for the SSI
if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
ssi_private->capture--;
+ if (ssi_private->first_stream == substream)
+ ssi_private->first_stream = ssi_private->second_stream;
+
+ ssi_private->second_stream = NULL;
+
/*
* If this is the last active substream, disable the SSI and release
* the IRQ.
#include <sound/soc-dapm.h>
#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
+#include <mach/hardware.h>
#include <linux/gpio.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/mcbsp.h>
#include "omap-mcbsp.h"
#include "omap-pcm.h"
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/arch/control.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/mcbsp.h>
+#include <mach/control.h>
+#include <mach/dma.h>
+#include <mach/mcbsp.h>
#include "omap-mcbsp.h"
#include "omap-pcm.h"
#include <sound/pcm_params.h>
#include <sound/soc.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include "omap-pcm.h"
static const struct snd_pcm_hardware omap_pcm_hardware = {
#include <asm/mach-types.h>
#include <asm/hardware/scoop.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/corgi.h>
-#include <asm/arch/audio.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/corgi.h>
+#include <mach/audio.h>
#include "../codecs/wm8731.h"
#include "pxa2xx-pcm.h"
#include <sound/soc-dapm.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/audio.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/audio.h>
#include "../codecs/wm9712.h"
#include "pxa2xx-pcm.h"
#include <sound/soc-dapm.h>
#include <asm/mach-types.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/audio.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/audio.h>
#include "../codecs/wm9712.h"
#include "pxa2xx-pcm.h"
#include <asm/mach-types.h>
#include <asm/hardware/locomo.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/poodle.h>
-#include <asm/arch/audio.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/poodle.h>
+#include <mach/audio.h>
#include "../codecs/wm8731.h"
#include "pxa2xx-pcm.h"
}
/* we need to unmute the HP at shutdown as the mute burns power on poodle */
-static int poodle_shutdown(struct snd_pcm_substream *substream)
+static void poodle_shutdown(struct snd_pcm_substream *substream)
{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct snd_soc_codec *codec = rtd->socdev->codec;
-
/* set = unmute headphone */
locomo_gpio_write(&poodle_locomo_device.dev,
POODLE_LOCOMO_GPIO_MUTE_L, 1);
locomo_gpio_write(&poodle_locomo_device.dev,
POODLE_LOCOMO_GPIO_MUTE_R, 1);
- return 0;
}
static int poodle_hw_params(struct snd_pcm_substream *substream,
SOC_ENUM_SINGLE_EXT(2, spk_function),
};
-static const snd_kcontrol_new_t wm8731_poodle_controls[] = {
+static const struct snd_kcontrol_new wm8731_poodle_controls[] = {
SOC_ENUM_EXT("Jack Function", poodle_enum[0], poodle_get_jack,
poodle_set_jack),
SOC_ENUM_EXT("Speaker Function", poodle_enum[1], poodle_get_spk,
#include <asm/irq.h>
#include <linux/mutex.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/audio.h>
#include "pxa2xx-pcm.h"
#include "pxa2xx-ac97.h"
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-gpio.h>
+#include <mach/audio.h>
#include "pxa2xx-pcm.h"
#include "pxa2xx-i2s.h"
#include <sound/soc.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/pxa-regs.h>
+#include <mach/audio.h>
#include "pxa2xx-pcm.h"
#include <asm/mach-types.h>
#include <asm/hardware/scoop.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/akita.h>
-#include <asm/arch/spitz.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/akita.h>
+#include <mach/spitz.h>
#include "../codecs/wm8750.h"
#include "pxa2xx-pcm.h"
#include "pxa2xx-i2s.h"
#include <sound/soc-dapm.h>
#include <asm/mach-types.h>
-#include <asm/arch/tosa.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/tosa.h>
+#include <mach/tosa.h>
+#include <mach/pxa-regs.h>
+#include <mach/hardware.h>
+#include <mach/audio.h>
#include "../codecs/wm9712.h"
#include "pxa2xx-pcm.h"
#include <sound/soc-dapm.h>
#include <sound/tlv.h>
-#include <asm/mach-types.h>
#include <asm/hardware/scoop.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/hardware.h>
-#include <asm/arch/audio.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
+#include <mach/hardware.h>
+#include <mach/audio.h>
#include <linux/io.h>
-#include <asm/arch/spi-gpio.h>
+#include <mach/spi-gpio.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <sound/pcm_params.h>
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <linux/io.h>
#include <asm/dma.h>
#include <asm/plat-s3c24xx/regs-s3c2412-iis.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/audio.h>
-#include <asm/arch/dma.h>
+#include <mach/regs-gpio.h>
+#include <mach/audio.h>
+#include <mach/dma.h>
#include "s3c24xx-pcm.h"
#include "s3c2412-i2s.h"
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/hardware.h>
+#include <mach/hardware.h>
#include <asm/plat-s3c/regs-ac97.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/audio.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/audio.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include "s3c24xx-pcm.h"
#include "s3c24xx-ac97.h"
#include <sound/initval.h>
#include <sound/soc.h>
-#include <asm/hardware.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-clock.h>
+#include <mach/audio.h>
#include <asm/dma.h>
-#include <asm/arch/dma.h>
+#include <mach/dma.h>
#include <asm/plat-s3c24xx/regs-iis.h>
#include <sound/soc.h>
#include <asm/dma.h>
-#include <asm/hardware.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/audio.h>
+#include <mach/hardware.h>
+#include <mach/dma.h>
+#include <mach/audio.h>
#include "s3c24xx-pcm.h"
return 0;
}
+EXPORT_SYMBOL_GPL(dapm_reg_event);
/*
* Scan each dapm widget for complete audio path.
}
EXPORT_SYMBOL_GPL(kvm_vcpu_uninit);
+#if defined(CONFIG_MMU_NOTIFIER) && defined(KVM_ARCH_WANT_MMU_NOTIFIER)
+static inline struct kvm *mmu_notifier_to_kvm(struct mmu_notifier *mn)
+{
+ return container_of(mn, struct kvm, mmu_notifier);
+}
+
+static void kvm_mmu_notifier_invalidate_page(struct mmu_notifier *mn,
+ struct mm_struct *mm,
+ unsigned long address)
+{
+ struct kvm *kvm = mmu_notifier_to_kvm(mn);
+ int need_tlb_flush;
+
+ /*
+ * When ->invalidate_page runs, the linux pte has been zapped
+ * already but the page is still allocated until
+ * ->invalidate_page returns. So if we increase the sequence
+ * here the kvm page fault will notice if the spte can't be
+ * established because the page is going to be freed. If
+ * instead the kvm page fault establishes the spte before
+ * ->invalidate_page runs, kvm_unmap_hva will release it
+ * before returning.
+ *
+ * The sequence increase only need to be seen at spin_unlock
+ * time, and not at spin_lock time.
+ *
+ * Increasing the sequence after the spin_unlock would be
+ * unsafe because the kvm page fault could then establish the
+ * pte after kvm_unmap_hva returned, without noticing the page
+ * is going to be freed.
+ */
+ spin_lock(&kvm->mmu_lock);
+ kvm->mmu_notifier_seq++;
+ need_tlb_flush = kvm_unmap_hva(kvm, address);
+ spin_unlock(&kvm->mmu_lock);
+
+ /* we've to flush the tlb before the pages can be freed */
+ if (need_tlb_flush)
+ kvm_flush_remote_tlbs(kvm);
+
+}
+
+static void kvm_mmu_notifier_invalidate_range_start(struct mmu_notifier *mn,
+ struct mm_struct *mm,
+ unsigned long start,
+ unsigned long end)
+{
+ struct kvm *kvm = mmu_notifier_to_kvm(mn);
+ int need_tlb_flush = 0;
+
+ spin_lock(&kvm->mmu_lock);
+ /*
+ * The count increase must become visible at unlock time as no
+ * spte can be established without taking the mmu_lock and
+ * count is also read inside the mmu_lock critical section.
+ */
+ kvm->mmu_notifier_count++;
+ for (; start < end; start += PAGE_SIZE)
+ need_tlb_flush |= kvm_unmap_hva(kvm, start);
+ spin_unlock(&kvm->mmu_lock);
+
+ /* we've to flush the tlb before the pages can be freed */
+ if (need_tlb_flush)
+ kvm_flush_remote_tlbs(kvm);
+}
+
+static void kvm_mmu_notifier_invalidate_range_end(struct mmu_notifier *mn,
+ struct mm_struct *mm,
+ unsigned long start,
+ unsigned long end)
+{
+ struct kvm *kvm = mmu_notifier_to_kvm(mn);
+
+ spin_lock(&kvm->mmu_lock);
+ /*
+ * This sequence increase will notify the kvm page fault that
+ * the page that is going to be mapped in the spte could have
+ * been freed.
+ */
+ kvm->mmu_notifier_seq++;
+ /*
+ * The above sequence increase must be visible before the
+ * below count decrease but both values are read by the kvm
+ * page fault under mmu_lock spinlock so we don't need to add
+ * a smb_wmb() here in between the two.
+ */
+ kvm->mmu_notifier_count--;
+ spin_unlock(&kvm->mmu_lock);
+
+ BUG_ON(kvm->mmu_notifier_count < 0);
+}
+
+static int kvm_mmu_notifier_clear_flush_young(struct mmu_notifier *mn,
+ struct mm_struct *mm,
+ unsigned long address)
+{
+ struct kvm *kvm = mmu_notifier_to_kvm(mn);
+ int young;
+
+ spin_lock(&kvm->mmu_lock);
+ young = kvm_age_hva(kvm, address);
+ spin_unlock(&kvm->mmu_lock);
+
+ if (young)
+ kvm_flush_remote_tlbs(kvm);
+
+ return young;
+}
+
+static const struct mmu_notifier_ops kvm_mmu_notifier_ops = {
+ .invalidate_page = kvm_mmu_notifier_invalidate_page,
+ .invalidate_range_start = kvm_mmu_notifier_invalidate_range_start,
+ .invalidate_range_end = kvm_mmu_notifier_invalidate_range_end,
+ .clear_flush_young = kvm_mmu_notifier_clear_flush_young,
+};
+#endif /* CONFIG_MMU_NOTIFIER && KVM_ARCH_WANT_MMU_NOTIFIER */
+
static struct kvm *kvm_create_vm(void)
{
struct kvm *kvm = kvm_arch_create_vm();
(struct kvm_coalesced_mmio_ring *)page_address(page);
#endif
+#if defined(CONFIG_MMU_NOTIFIER) && defined(KVM_ARCH_WANT_MMU_NOTIFIER)
+ {
+ int err;
+ kvm->mmu_notifier.ops = &kvm_mmu_notifier_ops;
+ err = mmu_notifier_register(&kvm->mmu_notifier, current->mm);
+ if (err) {
+#ifdef KVM_COALESCED_MMIO_PAGE_OFFSET
+ put_page(page);
+#endif
+ kfree(kvm);
+ return ERR_PTR(err);
+ }
+ }
+#endif
+
kvm->mm = current->mm;
atomic_inc(&kvm->mm->mm_count);
spin_lock_init(&kvm->mmu_lock);
#ifdef KVM_COALESCED_MMIO_PAGE_OFFSET
if (kvm->coalesced_mmio_ring != NULL)
free_page((unsigned long)kvm->coalesced_mmio_ring);
+#endif
+#if defined(CONFIG_MMU_NOTIFIER) && defined(KVM_ARCH_WANT_MMU_NOTIFIER)
+ mmu_notifier_unregister(&kvm->mmu_notifier, kvm->mm);
#endif
kvm_arch_destroy_vm(kvm);
mmdrop(mm);
memset(new.rmap, 0, npages * sizeof(*new.rmap));
new.user_alloc = user_alloc;
- new.userspace_addr = mem->userspace_addr;
+ /*
+ * hva_to_rmmap() serialzies with the mmu_lock and to be
+ * safe it has to ignore memslots with !user_alloc &&
+ * !userspace_addr.
+ */
+ if (user_alloc)
+ new.userspace_addr = mem->userspace_addr;
+ else
+ new.userspace_addr = 0;
}
if (npages && !new.lpage_info) {
int largepages = npages / KVM_PAGES_PER_HPAGE;
}
#endif /* not defined CONFIG_S390 */
- if (mem->slot >= kvm->nmemslots)
- kvm->nmemslots = mem->slot + 1;
-
if (!npages)
kvm_arch_flush_shadow(kvm);
+ spin_lock(&kvm->mmu_lock);
+ if (mem->slot >= kvm->nmemslots)
+ kvm->nmemslots = mem->slot + 1;
+
*memslot = new;
+ spin_unlock(&kvm->mmu_lock);
r = kvm_arch_set_memory_region(kvm, mem, old, user_alloc);
if (r) {
+ spin_lock(&kvm->mmu_lock);
*memslot = old;
+ spin_unlock(&kvm->mmu_lock);
goto out_free;
}
projects / linux-2.6-omap-h63xx.git / commitdiff