sbirq - IRQ # for CMI8330 chip (SB16)
sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
+ fmport - (optional) OPL3 I/O port
+ mpuport - (optional) MPU401 I/O port
+ mpuirq - (optional) MPU401 irq #
This module supports multiple cards and autoprobe.
The power-management is supported.
- Module snd-cs4232
- -----------------
-
- Module for sound cards based on CS4232/CS4232A ISA chips.
-
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
-
- with isapnp=0, the following options are available:
-
- port - port # for CS4232 chip (PnP setup - 0x534)
- cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
- mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
- fm_port - FM port # for CS4232 chip (PnP setup - 0x388), -1 = disable
- irq - IRQ # for CS4232 chip (5,7,9,11,12,15)
- mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
- dma1 - first DMA # for CS4232 chip (0,1,3)
- dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
-
- This module supports multiple cards. This module does not support autoprobe
- (if ISA PnP is not used) thus main port must be specified!!! Other ports are
- optional.
-
- The power-management is supported.
-
Module snd-cs4236
-----------------
- Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
+ Module for sound cards based on CS4232/CS4232A,
+ CS4235/CS4236/CS4236B/CS4237B/
CS4238B/CS4239 ISA chips.
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
The power-management is supported.
+ This module is aliased as snd-cs4232 since it provides the old
+ snd-cs4232 functionality, too.
+
Module snd-cs4281
-----------------
Module for ESS AudioDrive ES-1688 and ES-688 sound cards.
port - port # for ES-1688 chip (0x220,0x240,0x260)
+ fm_port - port # for OPL3 (option; share the same port as default)
mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
irq - IRQ # for ES-1688 chip (5,7,9,10)
mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = use LPIB, 2 = POSBUF)
probe_mask - Bitmask to probe codecs (default = -1, meaning all slots)
+ When the bit 8 (0x100) is set, the lower 8 bits are used
+ as the "fixed" codec slots; i.e. the driver probes the
+ slots regardless what hardware reports back
probe_only - Only probing and no codec initialization (default=off);
Useful to check the initial codec status for debugging
bdl_pos_adj - Specifies the DMA IRQ timing delay in samples.
This module supports multiple devices and PnP.
+ Module snd-msnd-classic
+ -----------------------
+
+ Module for Turtle Beach MultiSound Classic, Tahiti or Monterey
+ soundcards.
+
+ io - Port # for msnd-classic card
+ irq - IRQ # for msnd-classic card
+ mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000,
+ 0xe0000 or 0xe8000)
+ write_ndelay - enable write ndelay (default = 1)
+ calibrate_signal - calibrate signal (default = 0)
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+ digital - Digital daughterboard present (default = 0)
+ cfg - Config port (0x250, 0x260 or 0x270) default = PnP
+ reset - Reset all devices
+ mpu_io - MPU401 I/O port
+ mpu_irq - MPU401 irq#
+ ide_io0 - IDE port #0
+ ide_io1 - IDE port #1
+ ide_irq - IDE irq#
+ joystick_io - Joystick I/O port
+
+ The driver requires firmware files "turtlebeach/msndinit.bin" and
+ "turtlebeach/msndperm.bin" in the proper firmware directory.
+
+ See Documentation/sound/oss/MultiSound for important information
+ about this driver. Note that it has been discontinued, but the
+ Voyetra Turtle Beach knowledge base entry for it is still available
+ at
+ http://www.turtlebeach.com/site/kb_ftp/790.asp
+
+ Module snd-msnd-pinnacle
+ ------------------------
+
+ Module for Turtle Beach MultiSound Pinnacle/Fiji soundcards.
+
+ io - Port # for pinnacle/fiji card
+ irq - IRQ # for pinnalce/fiji card
+ mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000,
+ 0xe0000 or 0xe8000)
+ write_ndelay - enable write ndelay (default = 1)
+ calibrate_signal - calibrate signal (default = 0)
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ The driver requires firmware files "turtlebeach/pndspini.bin" and
+ "turtlebeach/pndsperm.bin" in the proper firmware directory.
+
Module snd-mtpav
----------------
Say Y here to include support for AD1848 (Analog Devices) or
CS4248 (Cirrus Logic - Crystal Semiconductors) chips.
- For newer chips from Cirrus Logic, use the CS4231, CS4232 or
- CS4236+ drivers.
+ For newer chips from Cirrus Logic, use the CS4231 or CS4232+
+ drivers.
To compile this driver as a module, choose M here: the module
will be called snd-ad1848.
tristate "C-Media CMI8330"
select SND_WSS_LIB
select SND_SB16_DSP
+ select SND_OPL3_LIB
+ select SND_MPU401_UART
help
Say Y here to include support for soundcards based on the
C-Media CMI8330 chip.
To compile this driver as a module, choose M here: the module
will be called snd-cs4231.
-config SND_CS4232
- tristate "Generic Cirrus Logic CS4232 driver"
- select SND_OPL3_LIB
- select SND_MPU401_UART
- select SND_WSS_LIB
- help
- Say Y here to include support for CS4232 chips from Cirrus
- Logic - Crystal Semiconductors.
-
- To compile this driver as a module, choose M here: the module
- will be called snd-cs4232.
-
config SND_CS4236
- tristate "Generic Cirrus Logic CS4236+ driver"
+ tristate "Generic Cirrus Logic CS4232/CS4236+ driver"
select SND_OPL3_LIB
select SND_MPU401_UART
select SND_WSS_LIB
help
- Say Y to include support for CS4235,CS4236,CS4237B,CS4238B,
- CS4239 chips from Cirrus Logic - Crystal Semiconductors.
+ Say Y to include support for CS4232,CS4235,CS4236,CS4237B,
+ CS4238B,CS4239 chips from Cirrus Logic - Crystal
+ Semiconductors.
To compile this driver as a module, choose M here: the module
will be called snd-cs4236.
you need to install the firmware files from the
alsa-firmware package.
+ config SND_MSND_PINNACLE
+ tristate "Turtle Beach MultiSound Pinnacle/Fiji driver"
+ depends on X86 && EXPERIMENTAL
+ select FW_LOADER
+ select SND_MPU401_UART
+ select SND_PCM
+ help
+ Say Y to include support for Turtle Beach MultiSound Pinnacle/
+ Fiji soundcards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called snd-msnd-pinnacle.
+
+ config SND_MSND_CLASSIC
+ tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
+ depends on X86 && EXPERIMENTAL
+ select FW_LOADER
+ select SND_MPU401_UART
+ select SND_PCM
+ help
+ Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
+ Monterey (not for the Pinnacle or Fiji).
+
+ See <file:Documentation/sound/oss/MultiSound> for important information
+ about this driver. Note that it has been discontinued, but the
+ Voyetra Turtle Beach knowledge base entry for it is still available
+ at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called snd-msnd-classic.
+
endif # SND_ISA
projects / linux-2.6-omap-h63xx.git / commitdiff