- ia64 (Does not support probes on instruction slot1.)
- sparc64 (Return probes not yet implemented.)
- arm
+- ppc
3. Configuring Kprobes
r) Freescale Display Interface Unit
s) Freescale on board FPGA
t) Freescael MSI interrupt controller
+ u) Freescale General-purpose Timers Module
VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node
......
};
+ Note that "par_io" nodes are obsolete, and should not be used for
+ the new device trees. Instead, each Par I/O bank should be represented
+ via its own gpio-controller node:
+
+ Required properties:
+ - #gpio-cells : should be "2".
+ - compatible : should be "fsl,<chip>-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank".
+ - reg : offset to the register set and its length.
+ - gpio-controller : node to identify gpio controllers.
+
+ Example:
+ qe_pio_a: gpio-controller@1400 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1400 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
vi) Pin configuration nodes
interrupt-parent = <&mpic>;
};
+ u) Freescale General-purpose Timers Module
+
+ Required properties:
+ - compatible : should be
+ "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+ "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+ "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+ - reg : should contain gtm registers location and length (0x40).
+ - interrupts : should contain four interrupts.
+ - interrupt-parent : interrupt source phandle.
+ - clock-frequency : specifies the frequency driving the timer.
+
+ Example:
+
+ timer@500 {
+ compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+ reg = <0x500 0x40>;
+ interrupts = <90 8 78 8 84 8 72 8>;
+ interrupt-parent = <&ipic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ };
+
+ timer@440 {
+ compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ };
VII - Marvell Discovery mv64[345]6x System Controller chips
===========================================================
help
Freescale Localbus support
+config FSL_GTM
+ bool
+ depends on PPC_83xx || QUICC_ENGINE || CPM2
+ help
+ Freescale General-purpose Timers support
+
# Yes MCA RS/6000s exist but Linux-PPC does not currently support any
config MCA
bool
cuImage.mpc8572ds
image-$(CONFIG_TQM8540) += cuImage.tqm8540
image-$(CONFIG_TQM8541) += cuImage.tqm8541
+image-$(CONFIG_TQM8548) += cuImage.tqm8548
image-$(CONFIG_TQM8555) += cuImage.tqm8555
image-$(CONFIG_TQM8560) += cuImage.tqm8560
image-$(CONFIG_SBC8548) += cuImage.sbc8548
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8347-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
/* phy type (ULPI or SERIAL) are only types supported for MPH */
/* port = 0 or 1 */
usb@22000 {
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 { /* For TSECs */
#address-cells = <1>;
#size-cells = <0>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8313-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8313-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
usb@23000 {
compatible = "fsl-usb2-dr";
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8315-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8315-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
interrupt-parent = <&ipic>;
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
crypto@30000 {
device_type = "crypto";
model = "SEC2";
compatible = "fsl-i2c";
reg = <0x3000 0x100>;
interrupts = <14 0x8>;
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
dfsrr;
};
reg = <0x4500 0x100>;
clock-frequency = <0>;
interrupts = <9 0x8>;
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
};
serial1: serial@4600 {
reg = <0x4600 0x100>;
clock-frequency = <0>;
interrupts = <10 0x8>;
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
+ };
+
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
};
crypto@30000 {
compatible = "talitos";
reg = <0x30000 0x7000>;
interrupts = <11 0x8>;
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
/* Rev. 2.2 */
num-channels = <1>;
channel-fifo-len = <24>;
descriptor-types-mask = <0x0122003f>;
};
- pic:pic@700 {
+ ipic:pic@700 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
compatible = "fsl,ucc-mdio";
phy00:ethernet-phy@00 {
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
interrupts = <0>;
reg = <0x0>;
device_type = "ethernet-phy";
};
phy04:ethernet-phy@04 {
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
interrupts = <0>;
reg = <0x4>;
device_type = "ethernet-phy";
reg = <0x80 0x80>;
big-endian;
interrupts = <32 0x8 33 0x8>; //high:32 low:33
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
};
};
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x10 AD16 (USB) */
- 0x8000 0x0 0x0 0x1 &pic 17 0x8
+ 0x8000 0x0 0x0 0x1 &ipic 17 0x8
/* IDSEL 0x11 AD17 (Mini1)*/
- 0x8800 0x0 0x0 0x1 &pic 18 0x8
- 0x8800 0x0 0x0 0x2 &pic 19 0x8
- 0x8800 0x0 0x0 0x3 &pic 20 0x8
- 0x8800 0x0 0x0 0x4 &pic 48 0x8
+ 0x8800 0x0 0x0 0x1 &ipic 18 0x8
+ 0x8800 0x0 0x0 0x2 &ipic 19 0x8
+ 0x8800 0x0 0x0 0x3 &ipic 20 0x8
+ 0x8800 0x0 0x0 0x4 &ipic 48 0x8
/* IDSEL 0x12 AD18 (PCI/Mini2) */
- 0x9000 0x0 0x0 0x1 &pic 19 0x8
- 0x9000 0x0 0x0 0x2 &pic 20 0x8
- 0x9000 0x0 0x0 0x3 &pic 48 0x8
- 0x9000 0x0 0x0 0x4 &pic 17 0x8>;
+ 0x9000 0x0 0x0 0x1 &ipic 19 0x8
+ 0x9000 0x0 0x0 0x2 &ipic 20 0x8
+ 0x9000 0x0 0x0 0x3 &ipic 48 0x8
+ 0x9000 0x0 0x0 0x4 &ipic 17 0x8>;
- interrupt-parent = <&pic>;
+ interrupt-parent = <&ipic>;
interrupts = <66 0x8>;
bus-range = <0x0 0x0>;
ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@22000 {
compatible = "fsl-usb2-mph";
reg = <0x22000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
/* phy type (ULPI or SERIAL) are only types supported for MPH */
/* port = 0 or 1 */
usb@22000 {
interrupt-parent = <&ipic>;
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8360-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
crypto@30000 {
device_type = "crypto";
model = "SEC2";
--- /dev/null
+/*
+ * MPC8360E RDK Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2007-2008 MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8360rdk";
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+ pci0 = &pci0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8360@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <32768>;
+ i-cache-size = <32768>;
+ /* filled by u-boot */
+ timebase-frequency = <0>;
+ bus-frequency = <0>;
+ clock-frequency = <0>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ /* filled by u-boot */
+ reg = <0 0>;
+ };
+
+ soc@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "fsl,mpc8360-immr", "fsl,immr", "fsl,soc",
+ "simple-bus";
+ ranges = <0 0xe0000000 0x200000>;
+ reg = <0xe0000000 0x200>;
+ /* filled by u-boot */
+ bus-frequency = <0>;
+
+ wdt@200 {
+ compatible = "mpc83xx_wdt";
+ reg = <0x200 0x100>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <16 8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+ };
+
+ serial0: serial@4500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ interrupts = <9 8>;
+ interrupt-parent = <&ipic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ };
+
+ serial1: serial@4600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ interrupts = <10 8>;
+ interrupt-parent = <&ipic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ };
+
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8360-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8360-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
+ crypto@30000 {
+ compatible = "fsl,sec2-crypto";
+ reg = <0x30000 0x10000>;
+ interrupts = <11 8>;
+ interrupt-parent = <&ipic>;
+ num-channels = <4>;
+ channel-fifo-len = <24>;
+ exec-units-mask = <0x7e>;
+ /*
+ * desc mask is for rev1.x, we need runtime fixup
+ * for >=2.x
+ */
+ descriptor-types-mask = <0x1010ebf>;
+ };
+
+ ipic: interrupt-controller@700 {
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ compatible = "fsl,pq2pro-pic", "fsl,ipic";
+ interrupt-controller;
+ reg = <0x700 0x100>;
+ };
+
+ qe_pio_b: gpio-controller@1418 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1418 0x18>;
+ gpio-controller;
+ };
+
+ qe_pio_e: gpio-controller@1460 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x1460 0x18>;
+ gpio-controller;
+ };
+
+ qe@100000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe", "simple-bus";
+ ranges = <0 0x100000 0x100000>;
+ reg = <0x100000 0x480>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ bus-frequency = <0>;
+ brg-frequency = <0>;
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0 0x10000 0xc000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0 0xc000>;
+ };
+ };
+
+ timer@440 {
+ compatible = "fsl,mpc8360-qe-gtm",
+ "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ /* filled by u-boot */
+ clock-frequency = <0>;
+ };
+
+ spi@4c0 {
+ cell-index = <0>;
+ compatible = "fsl,spi";
+ reg = <0x4c0 0x40>;
+ interrupts = <2>;
+ interrupt-parent = <&qeic>;
+ mode = "cpu-qe";
+ };
+
+ spi@500 {
+ cell-index = <1>;
+ compatible = "fsl,spi";
+ reg = <0x500 0x40>;
+ interrupts = <1>;
+ interrupt-parent = <&qeic>;
+ mode = "cpu-qe";
+ };
+
+ enet0: ucc@2000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ rx-clock-name = "none";
+ tx-clock-name = "clk9";
+ phy-handle = <&phy2>;
+ phy-connection-type = "rgmii-rxid";
+ /* filled by u-boot */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ enet1: ucc@3000 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <2>;
+ reg = <0x3000 0x200>;
+ interrupts = <33>;
+ interrupt-parent = <&qeic>;
+ rx-clock-name = "none";
+ tx-clock-name = "clk4";
+ phy-handle = <&phy4>;
+ phy-connection-type = "rgmii-rxid";
+ /* filled by u-boot */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ enet2: ucc@2600 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <7>;
+ reg = <0x2600 0x200>;
+ interrupts = <42>;
+ interrupt-parent = <&qeic>;
+ rx-clock-name = "clk20";
+ tx-clock-name = "clk19";
+ phy-handle = <&phy1>;
+ phy-connection-type = "mii";
+ /* filled by u-boot */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ enet3: ucc@3200 {
+ device_type = "network";
+ compatible = "ucc_geth";
+ cell-index = <4>;
+ reg = <0x3200 0x200>;
+ interrupts = <35>;
+ interrupt-parent = <&qeic>;
+ rx-clock-name = "clk8";
+ tx-clock-name = "clk7";
+ phy-handle = <&phy3>;
+ phy-connection-type = "mii";
+ /* filled by u-boot */
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ mdio@2120 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,ucc-mdio";
+ reg = <0x2120 0x18>;
+
+ phy1: ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ compatible = "national,DP83848VV";
+ reg = <1>;
+ };
+
+ phy2: ethernet-phy@2 {
+ device_type = "ethernet-phy";
+ compatible = "broadcom,BCM5481UA2KMLG";
+ reg = <2>;
+ };
+
+ phy3: ethernet-phy@3 {
+ device_type = "ethernet-phy";
+ compatible = "national,DP83848VV";
+ reg = <3>;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ compatible = "broadcom,BCM5481UA2KMLG";
+ reg = <4>;
+ };
+ };
+
+ serial2: ucc@2400 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ reg = <0x2400 0x200>;
+ cell-index = <5>;
+ port-number = <0>;
+ rx-clock-name = "brg7";
+ tx-clock-name = "brg8";
+ interrupts = <40>;
+ interrupt-parent = <&qeic>;
+ soft-uart;
+ };
+
+ serial3: ucc@3400 {
+ device_type = "serial";
+ compatible = "ucc_uart";
+ reg = <0x3400 0x200>;
+ cell-index = <6>;
+ port-number = <1>;
+ rx-clock-name = "brg13";
+ tx-clock-name = "brg14";
+ interrupts = <41>;
+ interrupt-parent = <&qeic>;
+ soft-uart;
+ };
+
+ qeic: interrupt-controller@80 {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ compatible = "fsl,qe-ic";
+ interrupt-controller;
+ reg = <0x80 0x80>;
+ big-endian;
+ interrupts = <32 8 33 8>;
+ interrupt-parent = <&ipic>;
+ };
+ };
+ };
+
+ localbus@e0005000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8360-localbus", "fsl,pq2pro-localbus",
+ "simple-bus";
+ reg = <0xe0005000 0xd8>;
+ ranges = <0 0 0xff800000 0x0800000
+ 1 0 0x60000000 0x0001000
+ 2 0 0x70000000 0x4000000>;
+
+ flash@0,0 {
+ compatible = "intel,PC28F640P30T85", "cfi-flash";
+ reg = <0 0 0x800000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ display@2,0 {
+ device_type = "display";
+ compatible = "fujitsu,MB86277", "fujitsu,mint";
+ reg = <2 0 0x4000000>;
+ fujitsu,sh3;
+ little-endian;
+ /* filled by u-boot */
+ address = <0>;
+ depth = <0>;
+ width = <0>;
+ height = <0>;
+ linebytes = <0>;
+ /* linux,opened; - added by uboot */
+ };
+ };
+
+ pci0: pci@e0008500 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ compatible = "fsl,mpc8360-pci", "fsl,mpc8349-pci";
+ reg = <0xe0008500 0x100>;
+ ranges = <0x02000000 0 0x90000000 0x90000000 0 0x10000000
+ 0x42000000 0 0x80000000 0x80000000 0 0x10000000
+ 0x01000000 0 0xe0300000 0xe0300000 0 0x00100000>;
+ interrupts = <66 8>;
+ interrupt-parent = <&ipic>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = </* miniPCI0 IDSEL 0x14 AD20 */
+ 0xa000 0 0 1 &ipic 18 8
+ 0xa000 0 0 2 &ipic 19 8
+
+ /* PCI1 IDSEL 0x15 AD21 */
+ 0xa800 0 0 1 &ipic 19 8
+ 0xa800 0 0 2 &ipic 20 8
+ 0xa800 0 0 3 &ipic 21 8
+ 0xa800 0 0 4 &ipic 18 8>;
+ /* filled by u-boot */
+ bus-range = <0 0>;
+ clock-frequency = <0>;
+ };
+};
interrupt-parent = <&ipic>;
};
- crypto@30000 {
- model = "SEC3";
- compatible = "talitos";
- reg = <0x30000 0x10000>;
- interrupts = <11 0x8>;
- interrupt-parent = <&ipic>;
- /* Rev. 3.0 geometry */
- num-channels = <4>;
- channel-fifo-len = <24>;
- exec-units-mask = <0x000001fe>;
- descriptor-types-mask = <0x03ab0ebf>;
- };
-
- sdhc@2e000 {
- model = "eSDHC";
- compatible = "fsl,esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- };
-
- sata@18000 {
- compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
- reg = <0x18000 0x1000>;
- interrupts = <44 0x8>;
- interrupt-parent = <&ipic>;
- };
-
- sata@19000 {
- compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
- reg = <0x19000 0x1000>;
- interrupts = <45 0x8>;
- interrupt-parent = <&ipic>;
- };
-
dma@82a8 {
#address-cells = <1>;
#size-cells = <1>;
};
};
+ crypto@30000 {
+ model = "SEC3";
+ compatible = "talitos";
+ reg = <0x30000 0x10000>;
+ interrupts = <11 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Rev. 3.0 geometry */
+ num-channels = <4>;
+ channel-fifo-len = <24>;
+ exec-units-mask = <0x000001fe>;
+ descriptor-types-mask = <0x03ab0ebf>;
+ };
+
+ sdhc@2e000 {
+ model = "eSDHC";
+ compatible = "fsl,esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
+ sata@18000 {
+ compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+ reg = <0x18000 0x1000>;
+ interrupts = <44 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
+ sata@19000 {
+ compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+ reg = <0x19000 0x1000>;
+ interrupts = <45 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+
/* IPIC
* interrupts cell = <intr #, sense>
* sense values match linux IORESOURCE_IRQ_* defines:
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8377-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8377-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8378-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8378-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8378-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8379-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8379-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8379-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <0x23000 0x1000>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8541-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8548-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8555-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
interrupts = <16 2>;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8568-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8568-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8568-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8568-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8568-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@c300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
+ reg = <0xc300 0x4>;
+ ranges = <0x0 0xc100 0x200>;
+ cell-index = <1>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <76 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <77 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <78 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <79 2>;
+ };
+ };
+
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8572-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8572-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8641-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
mode = "cpu";
};
+ dma@82a8 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+ reg = <0x82a8 4>;
+ ranges = <0 0x8100 0x1a8>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x80 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x100 0x80>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+ reg = <0x180 0x28>;
+ interrupt-parent = <&ipic>;
+ interrupts = <71 8>;
+ };
+ };
+
/* phy type (ULPI or SERIAL) are only types supported for MPH */
/* port = 0 or 1 */
usb@22000 {
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8548-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8641-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8641-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
dfsrr;
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
/dts-v1/;
/ {
- model = "tqm,8540";
- compatible = "tqm,8540", "tqm,85xx";
+ model = "tqc,tqm8540";
+ compatible = "tqc,tqm8540";
#address-cells = <1>;
#size-cells = <1>;
};
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8540-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
/dts-v1/;
/ {
- model = "tqm,8541";
- compatible = "tqm,8541", "tqm,85xx";
+ model = "tqc,tqm8541";
+ compatible = "tqc,tqm8541";
#address-cells = <1>;
#size-cells = <1>;
};
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8541-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8541-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
--- /dev/null
+/*
+ * TQM8548 Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2008 Wolfgang Grandegger <wg@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "tqc,tqm8548";
+ compatible = "tqc,tqm8548";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8548@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000>; // Filled in by U-Boot
+ };
+
+ soc8548@a0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x0 0xa0000000 0x100000>;
+ reg = <0xa0000000 0x1000>; // CCSRBAR
+ bus-frequency = <0>;
+
+ memory-controller@2000 {
+ compatible = "fsl,mpc8548-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupt-parent = <&mpic>;
+ interrupts = <18 2>;
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,mpc8548-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8548-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <4>;
+ device_type = "ethernet-phy";
+ };
+ phy5: ethernet-phy@5 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <5>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy2>;
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <35 2 36 2 40 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy1>;
+ };
+
+ enet2: ethernet@26000 {
+ cell-index = <2>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x26000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <31 2 32 2 33 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy3>;
+ };
+
+ enet3: ethernet@27000 {
+ cell-index = <3>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x27000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <37 2 38 2 39 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy4>;
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>; // reg base, size
+ clock-frequency = <0>; // should we fill in in uboot?
+ current-speed = <115200>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>; // reg base, size
+ clock-frequency = <0>; // should we fill in in uboot?
+ current-speed = <115200>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ global-utilities@e0000 { // global utilities reg
+ compatible = "fsl,mpc8548-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+
+ mpic: pic@40000 {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x40000 0x40000>;
+ compatible = "chrp,open-pic";
+ device_type = "open-pic";
+ };
+ };
+
+ localbus@a0005000 {
+ compatible = "fsl,mpc8548-localbus", "fsl,pq3-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xa0005000 0x100>; // BRx, ORx, etc.
+
+ ranges = <
+ 0 0x0 0xfc000000 0x04000000 // NOR FLASH bank 1
+ 1 0x0 0xf8000000 0x08000000 // NOR FLASH bank 0
+ 2 0x0 0xa3000000 0x00008000 // CAN (2 x i82527)
+ 3 0x0 0xa3010000 0x00008000 // NAND FLASH
+
+ >;
+
+ flash@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <1 0x0 0x8000000>;
+ bank-width = <4>;
+ device-width = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x00000000 0x00200000>;
+ };
+ partition@200000 {
+ label = "root";
+ reg = <0x00200000 0x00300000>;
+ };
+ partition@500000 {
+ label = "user";
+ reg = <0x00500000 0x07a00000>;
+ };
+ partition@7f00000 {
+ label = "env1";
+ reg = <0x07f00000 0x00040000>;
+ };
+ partition@7f40000 {
+ label = "env2";
+ reg = <0x07f40000 0x00040000>;
+ };
+ partition@7f80000 {
+ label = "u-boot";
+ reg = <0x07f80000 0x00080000>;
+ read-only;
+ };
+ };
+
+ /* Note: CAN support needs be enabled in U-Boot */
+ can0@2,0 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x0 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ can1@2,100 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x100 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ /* Note: NAND support needs to be enabled in U-Boot */
+ upm@3,0 {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ compatible = "fsl,upm-nand";
+ reg = <3 0x0 0x800>;
+ fsl,upm-addr-offset = <0x10>;
+ fsl,upm-cmd-offset = <0x08>;
+ chip-delay = <25>; // in micro-seconds
+
+ nand@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "fs";
+ reg = <0x00000000 0x01000000>;
+ };
+ };
+ };
+ };
+
+ pci0: pci@a0008000 {
+ cell-index = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+ device_type = "pci";
+ reg = <0xa0008000 0x1000>;
+ clock-frequency = <33333333>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 28 */
+ 0xe000 0 0 1 &mpic 2 1
+ 0xe000 0 0 2 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <24 2>;
+ bus-range = <0 0>;
+ ranges = <0x02000000 0 0x80000000 0x80000000 0 0x20000000
+ 0x01000000 0 0x00000000 0xa2000000 0 0x01000000>;
+ };
+
+ pci1: pcie@a000a000 {
+ cell-index = <2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x0 (PEX) */
+ 0x00000 0 0 1 &mpic 0 1
+ 0x00000 0 0 2 &mpic 1 1
+ 0x00000 0 0 3 &mpic 2 1
+ 0x00000 0 0 4 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <26 2>;
+ bus-range = <0 0xff>;
+ ranges = <0x02000000 0 0xb0000000 0xb0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xaf000000 0 0x08000000>;
+ clock-frequency = <33333333>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xa000a000 0x1000>;
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x02000000 0 0xb0000000 0x02000000 0
+ 0xb0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0x01000000 0
+ 0x00000000 0 0x08000000>;
+ };
+ };
+};
--- /dev/null
+/*
+ * TQM8548 Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2008 Wolfgang Grandegger <wg@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "tqc,tqm8548";
+ compatible = "tqc,tqm8548";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ ethernet3 = &enet3;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,8548@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>; // 32 bytes
+ i-cache-line-size = <32>; // 32 bytes
+ d-cache-size = <0x8000>; // L1, 32K
+ i-cache-size = <0x8000>; // L1, 32K
+ next-level-cache = <&L2>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000>; // Filled in by U-Boot
+ };
+
+ soc8548@e0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ ranges = <0x0 0xe0000000 0x100000>;
+ reg = <0xe0000000 0x1000>; // CCSRBAR
+ bus-frequency = <0>;
+
+ memory-controller@2000 {
+ compatible = "fsl,mpc8548-memory-controller";
+ reg = <0x2000 0x1000>;
+ interrupt-parent = <&mpic>;
+ interrupts = <18 2>;
+ };
+
+ L2: l2-cache-controller@20000 {
+ compatible = "fsl,mpc8548-l2-cache-controller";
+ reg = <0x20000 0x1000>;
+ cache-line-size = <32>; // 32 bytes
+ cache-size = <0x80000>; // L2, 512K
+ interrupt-parent = <&mpic>;
+ interrupts = <16 2>;
+ };
+
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ compatible = "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ dfsrr;
+ };
+
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8548-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8548-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
+ mdio@24520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x24520 0x20>;
+
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <4>;
+ device_type = "ethernet-phy";
+ };
+ phy5: ethernet-phy@5 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <5>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ enet0: ethernet@24000 {
+ cell-index = <0>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy2>;
+ };
+
+ enet1: ethernet@25000 {
+ cell-index = <1>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <35 2 36 2 40 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy1>;
+ };
+
+ enet2: ethernet@26000 {
+ cell-index = <2>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x26000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <31 2 32 2 33 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy3>;
+ };
+
+ enet3: ethernet@27000 {
+ cell-index = <3>;
+ device_type = "network";
+ model = "eTSEC";
+ compatible = "gianfar";
+ reg = <0x27000 0x1000>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <37 2 38 2 39 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy4>;
+ };
+
+ serial0: serial@4500 {
+ cell-index = <0>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>; // reg base, size
+ clock-frequency = <0>; // should we fill in in uboot?
+ current-speed = <115200>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ serial1: serial@4600 {
+ cell-index = <1>;
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>; // reg base, size
+ clock-frequency = <0>; // should we fill in in uboot?
+ current-speed = <115200>;
+ interrupts = <42 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ global-utilities@e0000 { // global utilities reg
+ compatible = "fsl,mpc8548-guts";
+ reg = <0xe0000 0x1000>;
+ fsl,has-rstcr;
+ };
+
+ mpic: pic@40000 {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <2>;
+ reg = <0x40000 0x40000>;
+ compatible = "chrp,open-pic";
+ device_type = "open-pic";
+ };
+ };
+
+ localbus@e0005000 {
+ compatible = "fsl,mpc8548-localbus", "fsl,pq3-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xe0005000 0x100>; // BRx, ORx, etc.
+
+ ranges = <
+ 0 0x0 0xfc000000 0x04000000 // NOR FLASH bank 1
+ 1 0x0 0xf8000000 0x08000000 // NOR FLASH bank 0
+ 2 0x0 0xe3000000 0x00008000 // CAN (2 x i82527)
+ 3 0x0 0xe3010000 0x00008000 // NAND FLASH
+
+ >;
+
+ flash@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <1 0x0 0x8000000>;
+ bank-width = <4>;
+ device-width = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x00000000 0x00200000>;
+ };
+ partition@200000 {
+ label = "root";
+ reg = <0x00200000 0x00300000>;
+ };
+ partition@500000 {
+ label = "user";
+ reg = <0x00500000 0x07a00000>;
+ };
+ partition@7f00000 {
+ label = "env1";
+ reg = <0x07f00000 0x00040000>;
+ };
+ partition@7f40000 {
+ label = "env2";
+ reg = <0x07f40000 0x00040000>;
+ };
+ partition@7f80000 {
+ label = "u-boot";
+ reg = <0x07f80000 0x00080000>;
+ read-only;
+ };
+ };
+
+ /* Note: CAN support needs be enabled in U-Boot */
+ can0@2,0 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x0 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ can1@2,100 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x100 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ /* Note: NAND support needs to be enabled in U-Boot */
+ upm@3,0 {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ compatible = "fsl,upm-nand";
+ reg = <3 0x0 0x800>;
+ fsl,upm-addr-offset = <0x10>;
+ fsl,upm-cmd-offset = <0x08>;
+ chip-delay = <25>; // in micro-seconds
+
+ nand@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "fs";
+ reg = <0x00000000 0x01000000>;
+ };
+ };
+ };
+ };
+
+ pci0: pci@e0008000 {
+ cell-index = <0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+ device_type = "pci";
+ reg = <0xe0008000 0x1000>;
+ clock-frequency = <33333333>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 28 */
+ 0xe000 0 0 1 &mpic 2 1
+ 0xe000 0 0 2 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <24 2>;
+ bus-range = <0 0>;
+ ranges = <0x02000000 0 0x80000000 0x80000000 0 0x20000000
+ 0x01000000 0 0x00000000 0xe2000000 0 0x01000000>;
+ };
+
+ pci1: pcie@e000a000 {
+ cell-index = <2>;
+ interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+ interrupt-map = <
+ /* IDSEL 0x0 (PEX) */
+ 0x00000 0 0 1 &mpic 0 1
+ 0x00000 0 0 2 &mpic 1 1
+ 0x00000 0 0 3 &mpic 2 1
+ 0x00000 0 0 4 &mpic 3 1>;
+
+ interrupt-parent = <&mpic>;
+ interrupts = <26 2>;
+ bus-range = <0 0xff>;
+ ranges = <0x02000000 0 0xc0000000 0xc0000000 0 0x20000000
+ 0x01000000 0 0x00000000 0xef000000 0 0x08000000>;
+ clock-frequency = <33333333>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ reg = <0xe000a000 0x1000>;
+ compatible = "fsl,mpc8548-pcie";
+ device_type = "pci";
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ ranges = <0x02000000 0 0xc0000000 0x02000000 0
+ 0xc0000000 0 0x20000000
+ 0x01000000 0 0x00000000 0x01000000 0
+ 0x00000000 0 0x08000000>;
+ };
+ };
+};
/dts-v1/;
/ {
- model = "tqm,8555";
- compatible = "tqm,8555", "tqm,85xx";
+ model = "tqc,tqm8555";
+ compatible = "tqc,tqm8555";
#address-cells = <1>;
#size-cells = <1>;
};
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8555-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8555-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
* TQM 8560 Device Tree Source
*
* Copyright 2008 Freescale Semiconductor Inc.
+ * Copyright 2008 Wolfgang Grandegger <wg@grandegger.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
/dts-v1/;
/ {
- model = "tqm,8560";
- compatible = "tqm,8560", "tqm,85xx";
+ model = "tqc,tqm8560";
+ compatible = "tqc,tqm8560";
#address-cells = <1>;
#size-cells = <1>;
};
};
+ dma@21300 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+ reg = <0x21300 0x4>;
+ ranges = <0x0 0x21100 0x200>;
+ cell-index = <0>;
+ dma-channel@0 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x0 0x80>;
+ cell-index = <0>;
+ interrupt-parent = <&mpic>;
+ interrupts = <20 2>;
+ };
+ dma-channel@80 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x80 0x80>;
+ cell-index = <1>;
+ interrupt-parent = <&mpic>;
+ interrupts = <21 2>;
+ };
+ dma-channel@100 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x100 0x80>;
+ cell-index = <2>;
+ interrupt-parent = <&mpic>;
+ interrupts = <22 2>;
+ };
+ dma-channel@180 {
+ compatible = "fsl,mpc8560-dma-channel",
+ "fsl,eloplus-dma-channel";
+ reg = <0x180 0x80>;
+ cell-index = <3>;
+ interrupt-parent = <&mpic>;
+ interrupts = <23 2>;
+ };
+ };
+
mdio@24520 {
#address-cells = <1>;
#size-cells = <0>;
};
};
+ localbus@e0005000 {
+ compatible = "fsl,mpc8560-localbus", "fsl,pq3-localbus",
+ "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ reg = <0xe0005000 0x100>; // BRx, ORx, etc.
+
+ ranges = <
+ 0 0x0 0xfc000000 0x04000000 // NOR FLASH bank 1
+ 1 0x0 0xf8000000 0x08000000 // NOR FLASH bank 0
+ 2 0x0 0xe3000000 0x00008000 // CAN (2 x i82527)
+ >;
+
+ flash@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <1 0x0 0x8000000>;
+ bank-width = <4>;
+ device-width = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x00000000 0x00200000>;
+ };
+ partition@200000 {
+ label = "root";
+ reg = <0x00200000 0x00300000>;
+ };
+ partition@500000 {
+ label = "user";
+ reg = <0x00500000 0x07a00000>;
+ };
+ partition@7f00000 {
+ label = "env1";
+ reg = <0x07f00000 0x00040000>;
+ };
+ partition@7f40000 {
+ label = "env2";
+ reg = <0x07f40000 0x00040000>;
+ };
+ partition@7f80000 {
+ label = "u-boot";
+ reg = <0x07f80000 0x00080000>;
+ read-only;
+ };
+ };
+
+ /* Note: CAN support needs be enabled in U-Boot */
+ can0@2,0 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x0 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+
+ can1@2,100 {
+ compatible = "intel,82527"; // Bosch CC770
+ reg = <2 0x100 0x100>;
+ interrupts = <4 0>;
+ interrupt-parent = <&mpic>;
+ };
+ };
+
pci0: pci@e0008000 {
cell-index = <0>;
#interrupt-cells = <1>;
*-tqm8541|*-mpc8560*|*-tqm8560|*-tqm8555|*-ksi8560*)
platformo=$object/cuboot-85xx-cpm2.o
;;
- *-mpc85*|*-tqm8540|*-sbc85*)
+ *-mpc85*|*-tqm85*|*-sbc85*)
platformo=$object/cuboot-85xx.o
;;
esac
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.26-rc2
+# Mon May 19 21:12:32 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+CONFIG_6xx=y
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_PPC_FPU=y
+# CONFIG_FSL_EMB_PERFMON is not set
+CONFIG_PPC_STD_MMU=y
+CONFIG_PPC_STD_MMU_32=y
+# CONFIG_PPC_MM_SLICES is not set
+# CONFIG_SMP is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_IRQ_PER_CPU=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_KALLSYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+# CONFIG_EPOLL is not set
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+# CONFIG_HAVE_DMA_ATTRS is not set
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
+
+#
+# Platform support
+#
+# CONFIG_PPC_MULTIPLATFORM is not set
+# CONFIG_PPC_82xx is not set
+CONFIG_PPC_83xx=y
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_MPC512x is not set
+# CONFIG_PPC_MPC5121 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_MPC83xx=y
+# CONFIG_MPC831x_RDB is not set
+# CONFIG_MPC832x_MDS is not set
+# CONFIG_MPC832x_RDB is not set
+# CONFIG_MPC834x_MDS is not set
+# CONFIG_MPC834x_ITX is not set
+# CONFIG_MPC836x_MDS is not set
+CONFIG_MPC836x_RDK=y
+# CONFIG_MPC837x_MDS is not set
+# CONFIG_MPC837x_RDB is not set
+# CONFIG_SBC834x is not set
+CONFIG_IPIC=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+CONFIG_QUICC_ENGINE=y
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+# CONFIG_IOMMU_HELPER is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_HAS_WALK_MEMORY=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_FORCE_MAX_ZONEORDER=11
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_FSL_LBC=y
+CONFIG_FSL_GTM=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+# CONFIG_PCIEPORTBUS is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+# CONFIG_HAS_RAPIDIO is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_PAGE_OFFSET=0xc0000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_PHYSICAL_START=0x00000000
+CONFIG_TASK_SIZE=0xc0000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_OF_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_NOSWAP=y
+# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set
+# CONFIG_MTD_CFI_GEOMETRY is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_OTP is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_INTEL_VR_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_I2C=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+CONFIG_BROADCOM_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+# CONFIG_NET_ETHERNET is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
+# CONFIG_E1000E_ENABLED is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_GIANFAR is not set
+CONFIG_UCC_GETH=y
+CONFIG_UGETH_NAPI=y
+# CONFIG_UGETH_MAGIC_PACKET is not set
+# CONFIG_UGETH_FILTERING is not set
+# CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_SERIAL_QE=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+
+#
+# I2C Hardware Bus support
+#
+# CONFIG_I2C_ALI1535 is not set
+# CONFIG_I2C_ALI1563 is not set
+# CONFIG_I2C_ALI15X3 is not set
+# CONFIG_I2C_AMD756 is not set
+# CONFIG_I2C_AMD8111 is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_I801 is not set
+# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
+CONFIG_I2C_MPC=y
+# CONFIG_I2C_NFORCE2 is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_PROSAVAGE is not set
+# CONFIG_I2C_SAVAGE4 is not set
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_SIS5595 is not set
+# CONFIG_I2C_SIS630 is not set
+# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_STUB is not set
+# CONFIG_I2C_VIA is not set
+# CONFIG_I2C_VIAPRO is not set
+# CONFIG_I2C_VOODOO3 is not set
+# CONFIG_I2C_PCA_PLATFORM is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_EEPROM is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_MPC83xx=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_HAVE_GPIO_LIB=y
+
+#
+# GPIO Support
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_83xx_WDT=y
+
+#
+# PCI-based Watchdog Cards
+#
+# CONFIG_PCIPCWATCHDOG is not set
+# CONFIG_WDTPCI is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+CONFIG_FB_MACMODES=y
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+CONFIG_FB_OF=y
+# CONFIG_FB_CT65550 is not set
+# CONFIG_FB_ASILIANT is not set
+# CONFIG_FB_IMSTT is not set
+# CONFIG_FB_VGA16 is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_NVIDIA is not set
+# CONFIG_FB_RIVA is not set
+# CONFIG_FB_MATROX is not set
+# CONFIG_FB_RADEON is not set
+# CONFIG_FB_ATY128 is not set
+# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
+# CONFIG_FB_SAVAGE is not set
+# CONFIG_FB_SIS is not set
+# CONFIG_FB_NEOMAGIC is not set
+# CONFIG_FB_KYRO is not set
+# CONFIG_FB_3DFX is not set
+# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
+# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
+# CONFIG_FB_FSL_DIU is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_BIND34 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+CONFIG_UCC_SLOW=y
+CONFIG_UCC_FAST=y
+CONFIG_UCC=y
+CONFIG_QE_GPIO=y
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_IRQSTACKS is not set
+CONFIG_PPC_EARLY_DEBUG=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
+# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set
+# CONFIG_PPC_EARLY_DEBUG_BEAT is not set
+# CONFIG_PPC_EARLY_DEBUG_44x is not set
+# CONFIG_PPC_EARLY_DEBUG_40x is not set
+# CONFIG_PPC_EARLY_DEBUG_CPM is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+# CONFIG_PPC_CLOCK is not set
+CONFIG_PPC_LIB_RHEAP=y
+# CONFIG_VIRTUALIZATION is not set
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.26-rc4
+# Tue Jun 3 14:39:30 2008
+#
+# CONFIG_PPC64 is not set
+
+#
+# Processor support
+#
+# CONFIG_6xx is not set
+CONFIG_PPC_85xx=y
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+# CONFIG_44x is not set
+# CONFIG_E200 is not set
+CONFIG_E500=y
+CONFIG_BOOKE=y
+CONFIG_FSL_BOOKE=y
+CONFIG_FSL_EMB_PERFMON=y
+# CONFIG_PHYS_64BIT is not set
+CONFIG_SPE=y
+# CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC32=y
+CONFIG_WORD_SIZE=32
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+CONFIG_IRQ_PER_CPU=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFAULT_UIMAGE=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_CGROUPS is not set
+CONFIG_GROUP_SCHED=y
+# CONFIG_FAIR_GROUP_SCHED is not set
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_COMPAT_BRK=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+# CONFIG_HAVE_DMA_ATTRS is not set
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+# CONFIG_KMOD is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+# CONFIG_BLK_DEV_BSG is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC512x is not set
+# CONFIG_PPC_MPC5121 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_MPC85xx=y
+# CONFIG_MPC8540_ADS is not set
+# CONFIG_MPC8560_ADS is not set
+# CONFIG_MPC85xx_CDS is not set
+# CONFIG_MPC85xx_MDS is not set
+# CONFIG_MPC85xx_DS is not set
+# CONFIG_KSI8560 is not set
+# CONFIG_STX_GP3 is not set
+# CONFIG_TQM8540 is not set
+# CONFIG_TQM8541 is not set
+CONFIG_TQM8548=y
+# CONFIG_TQM8555 is not set
+# CONFIG_TQM8560 is not set
+# CONFIG_SBC8548 is not set
+# CONFIG_SBC8560 is not set
+CONFIG_TQM85xx=y
+# CONFIG_IPIC is not set
+CONFIG_MPIC=y
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+CONFIG_PPC_CPM_NEW_BINDING=y
+# CONFIG_FSL_ULI1575 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+# CONFIG_SCHED_HRTICK is not set
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+CONFIG_BINFMT_MISC=y
+CONFIG_MATH_EMULATION=y
+# CONFIG_IOMMU_HELPER is not set
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_HAS_WALK_MEMORY=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_BOUNCE=y
+CONFIG_VIRT_TO_BUS=y
+CONFIG_FORCE_MAX_ZONEORDER=11
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+# CONFIG_SECCOMP is not set
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+CONFIG_FSL_SOC=y
+CONFIG_FSL_PCI=y
+CONFIG_FSL_LBC=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_SYSCALL=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIEAER=y
+# CONFIG_PCIEASPM is not set
+CONFIG_ARCH_SUPPORTS_MSI=y
+# CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
+# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCCARD is not set
+# CONFIG_HOTPLUG_PCI is not set
+# CONFIG_HAS_RAPIDIO is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_PAGE_OFFSET=0xc0000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_PHYSICAL_START=0x00000000
+CONFIG_PHYSICAL_ALIGN=0x10000000
+CONFIG_TASK_SIZE=0xc0000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=y
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_OF_PARTS=y
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+# CONFIG_MTD_BLOCK is not set
+# CONFIG_MTD_BLOCK_RO is not set
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP_OF=y
+# CONFIG_MTD_INTEL_VR_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+CONFIG_MTD_NAND_ECC_SMC=y
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_CAFE is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_NAND_FSL_ELBC is not set
+CONFIG_MTD_NAND_FSL_UPM=y
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=m
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+CONFIG_OF_DEVICE=y
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=32768
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_PHANTOM is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+CONFIG_HAVE_IDE=y
+CONFIG_IDE=y
+CONFIG_IDE_MAX_HWIFS=4
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+# CONFIG_BLK_DEV_IDEDISK is not set
+# CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+CONFIG_IDE_GENERIC=y
+# CONFIG_BLK_DEV_PLATFORM is not set
+CONFIG_BLK_DEV_IDEDMA_SFF=y
+
+#
+# PCI IDE chipsets support
+#
+CONFIG_BLK_DEV_IDEPCI=y
+CONFIG_IDEPCI_PCIBUS_ORDER=y
+# CONFIG_BLK_DEV_OFFBOARD is not set
+CONFIG_BLK_DEV_GENERIC=y
+# CONFIG_BLK_DEV_OPTI621 is not set
+CONFIG_BLK_DEV_IDEDMA_PCI=y
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+CONFIG_BLK_DEV_VIA82CXXX=y
+# CONFIG_BLK_DEV_TC86C001 is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_BLK_DEV_HD_ONLY is not set
+# CONFIG_BLK_DEV_HD is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+CONFIG_E1000=y
+CONFIG_E1000_NAPI=y
+# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_E1000E is not set
+# CONFIG_E1000E_ENABLED is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+CONFIG_GIANFAR=y
+CONFIG_GFAR_NAPI=y
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+CONFIG_NETDEV_10000=y
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
+# CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_SFC is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_PCI=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+# CONFIG_SERIAL_OF_PLATFORM is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+CONFIG_GEN_RTC=y
+# CONFIG_GEN_RTC_X is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+# CONFIG_SPI is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_I5K_AMB is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SIS5595 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_VT8231 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
+# CONFIG_EDAC is not set
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_UIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+# CONFIG_NFS_V3 is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_BIND34 is not set
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+# CONFIG_MSDOS_PARTITION is not set
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_SYSV68_PARTITION is not set
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_IRQSTACKS is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+# CONFIG_PPC_CLOCK is not set
+# CONFIG_VIRTUALIZATION is not set
obj-$(CONFIG_IBMEBUS) += ibmebus.o
obj-$(CONFIG_GENERIC_TBSYNC) += smp-tbsync.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
+obj-$(CONFIG_E500) += idle_e500.o
obj-$(CONFIG_6xx) += idle_6xx.o l2cr_6xx.o cpu_setup_6xx.o
obj-$(CONFIG_TAU) += tau_6xx.o
obj-$(CONFIG_HIBERNATION) += swsusp.o suspend.o \
.pvr_mask = 0xffff0000,
.pvr_value = 0x80200000,
.cpu_name = "e500",
- /* xxx - galak: add CPU_FTR_MAYBE_CAN_DOZE */
.cpu_features = CPU_FTRS_E500,
.cpu_user_features = COMMON_USER_BOOKE |
PPC_FEATURE_HAS_SPE_COMP |
.pvr_mask = 0xffff0000,
.pvr_value = 0x80210000,
.cpu_name = "e500v2",
- /* xxx - galak: add CPU_FTR_MAYBE_CAN_DOZE */
.cpu_features = CPU_FTRS_E500_2,
.cpu_user_features = COMMON_USER_BOOKE |
PPC_FEATURE_HAS_SPE_COMP |
.machine_check = machine_check_e500,
.platform = "ppc8548",
},
+ { /* e500mc */
+ .pvr_mask = 0xffff0000,
+ .pvr_value = 0x80230000,
+ .cpu_name = "e500mc",
+ .cpu_features = CPU_FTRS_E500MC,
+ .cpu_user_features = COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+ .icache_bsize = 64,
+ .dcache_bsize = 64,
+ .num_pmcs = 4,
+ .oprofile_cpu_type = "ppc/e500", /* xxx - galak, e500mc? */
+ .oprofile_type = PPC_OPROFILE_FSL_EMB,
+ .machine_check = machine_check_e500,
+ .platform = "ppce500mc",
+ },
{ /* default match */
.pvr_mask = 0x00000000,
.pvr_value = 0x00000000,
cmplw r1,r9 /* if r1 <= ksp_limit */
ble- stack_ovf /* then the kernel stack overflowed */
5:
-#ifdef CONFIG_6xx
+#if defined(CONFIG_6xx) || defined(CONFIG_E500)
rlwinm r9,r1,0,0,31-THREAD_SHIFT
tophys(r9,r9) /* check local flags */
lwz r12,TI_LOCAL_FLAGS(r9)
mtcrf 0x01,r12
bt- 31-TLF_NAPPING,4f
bt- 31-TLF_SLEEPING,7f
-#endif /* CONFIG_6xx */
+#endif /* CONFIG_6xx || CONFIG_E500 */
.globl transfer_to_handler_cont
transfer_to_handler_cont:
3:
SYNC
RFI /* jump to handler, enable MMU */
-#ifdef CONFIG_6xx
+#if defined (CONFIG_6xx) || defined(CONFIG_E500)
4: rlwinm r12,r12,0,~_TLF_NAPPING
stw r12,TI_LOCAL_FLAGS(r9)
- b power_save_6xx_restore
+ b power_save_ppc32_restore
7: rlwinm r12,r12,0,~_TLF_SLEEPING
stw r12,TI_LOCAL_FLAGS(r9)
#define MCHECK_STACK_BASE mcheckirq_ctx
#define CRIT_STACK_BASE critirq_ctx
-/* only on e200 for now */
+/* only on e500mc/e200 */
#define DEBUG_STACK_BASE dbgirq_ctx
+#ifdef CONFIG_PPC_E500MC
+#define DEBUG_SPRG SPRN_SPRG9
+#else
#define DEBUG_SPRG SPRN_SPRG6W
+#endif
#define EXC_LVL_FRAME_OVERHEAD (THREAD_SIZE - INT_FRAME_SIZE - EXC_LVL_SIZE)
* the code where the exception occurred (since exception entry \
* doesn't turn off DE automatically). We simulate the effect \
* of turning off DE on entry to an exception handler by turning \
- * off DE in the CSRR1 value and clearing the debug status. \
+ * off DE in the DSRR1 value and clearing the debug status. \
*/ \
mfspr r10,SPRN_DBSR; /* check single-step/branch taken */ \
andis. r10,r10,DBSR_IC@h; \
RFDI; \
b .; \
\
- /* continue normal handling for a critical exception... */ \
+ /* continue normal handling for a debug exception... */ \
2: mfspr r4,SPRN_DBSR; \
addi r3,r1,STACK_FRAME_OVERHEAD; \
EXC_XFER_TEMPLATE(DebugException, 0x2008, (MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)), NOCOPY, debug_transfer_to_handler, ret_from_debug_exc)
#include <asm/thread_info.h>
#include <asm/ppc_asm.h>
#include <asm/asm-offsets.h>
+#include <asm/cache.h>
#include "head_booke.h"
/* As with the other PowerPC ports, it is expected that when code
SET_IVOR(13, DataTLBError);
SET_IVOR(14, InstructionTLBError);
SET_IVOR(15, DebugDebug);
-#if defined(CONFIG_E500)
+#if defined(CONFIG_E500) && !defined(CONFIG_PPC_E500MC)
SET_IVOR(15, DebugCrit);
#endif
SET_IVOR(32, SPEUnavailable);
#ifndef CONFIG_E200
SET_IVOR(35, PerformanceMonitor);
#endif
+#ifdef CONFIG_PPC_E500MC
+ SET_IVOR(36, Doorbell);
+#endif
/* Establish the interrupt vector base */
lis r4,interrupt_base@h /* IVPR only uses the high 16-bits */
/* Performance Monitor */
EXCEPTION(0x2060, PerformanceMonitor, performance_monitor_exception, EXC_XFER_STD)
+#ifdef CONFIG_PPC_E500MC
+ EXCEPTION(0x2070, Doorbell, unknown_exception, EXC_XFER_EE)
+#endif
/* Debug Interrupt */
DEBUG_DEBUG_EXCEPTION
-#if defined(CONFIG_E500)
+#if defined(CONFIG_E500) && !defined(CONFIG_PPC_E500MC)
DEBUG_CRIT_EXCEPTION
#endif
isync /* Force context change */
blr
+_GLOBAL(flush_dcache_L1)
+ mfspr r3,SPRN_L1CFG0
+
+ rlwinm r5,r3,9,3 /* Extract cache block size */
+ twlgti r5,1 /* Only 32 and 64 byte cache blocks
+ * are currently defined.
+ */
+ li r4,32
+ subfic r6,r5,2 /* r6 = log2(1KiB / cache block size) -
+ * log2(number of ways)
+ */
+ slw r5,r4,r5 /* r5 = cache block size */
+
+ rlwinm r7,r3,0,0xff /* Extract number of KiB in the cache */
+ mulli r7,r7,13 /* An 8-way cache will require 13
+ * loads per set.
+ */
+ slw r7,r7,r6
+
+ /* save off HID0 and set DCFA */
+ mfspr r8,SPRN_HID0
+ ori r9,r8,HID0_DCFA@l
+ mtspr SPRN_HID0,r9
+ isync
+
+ lis r4,KERNELBASE@h
+ mtctr r7
+
+1: lwz r3,0(r4) /* Load... */
+ add r4,r4,r5
+ bdnz 1b
+
+ msync
+ lis r4,KERNELBASE@h
+ mtctr r7
+
+1: dcbf 0,r4 /* ...and flush. */
+ add r4,r4,r5
+ bdnz 1b
+
+ /* restore HID0 */
+ mtspr SPRN_HID0,r8
+ isync
+
+ blr
+
/*
* We put a few things here that have to be page-aligned. This stuff
* goes at the beginning of the data segment, which is page-aligned.
* address of current. R11 points to the exception frame (physical
* address). We have to preserve r10.
*/
-_GLOBAL(power_save_6xx_restore)
+_GLOBAL(power_save_ppc32_restore)
lwz r9,_LINK(r11) /* interrupted in ppc6xx_idle: */
stw r9,_NIP(r11) /* make it do a blr */
--- /dev/null
+/*
+ * Copyright (C) 2008 Freescale Semiconductor, Inc. All rights reserved.
+ * Dave Liu <daveliu@freescale.com>
+ * copy from idle_6xx.S and modify for e500 based processor,
+ * implement the power_save function in idle.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/threads.h>
+#include <asm/reg.h>
+#include <asm/page.h>
+#include <asm/cputable.h>
+#include <asm/thread_info.h>
+#include <asm/ppc_asm.h>
+#include <asm/asm-offsets.h>
+
+ .text
+
+_GLOBAL(e500_idle)
+ rlwinm r3,r1,0,0,31-THREAD_SHIFT /* current thread_info */
+ lwz r4,TI_LOCAL_FLAGS(r3) /* set napping bit */
+ ori r4,r4,_TLF_NAPPING /* so when we take an exception */
+ stw r4,TI_LOCAL_FLAGS(r3) /* it will return to our caller */
+
+ /* Check if we can nap or doze, put HID0 mask in r3 */
+ lis r3,0
+BEGIN_FTR_SECTION
+ lis r3,HID0_DOZE@h
+END_FTR_SECTION_IFSET(CPU_FTR_CAN_DOZE)
+
+BEGIN_FTR_SECTION
+ /* Now check if user enabled NAP mode */
+ lis r4,powersave_nap@ha
+ lwz r4,powersave_nap@l(r4)
+ cmpwi 0,r4,0
+ beq 1f
+ stwu r1,-16(r1)
+ mflr r0
+ stw r0,20(r1)
+ bl flush_dcache_L1
+ lwz r0,20(r1)
+ addi r1,r1,16
+ mtlr r0
+ lis r3,HID0_NAP@h
+END_FTR_SECTION_IFSET(CPU_FTR_CAN_NAP)
+BEGIN_FTR_SECTION
+ msync
+ li r7,L2CSR0_L2FL@l
+ mtspr SPRN_L2CSR0,r7
+2:
+ mfspr r7,SPRN_L2CSR0
+ andi. r4,r7,L2CSR0_L2FL@l
+ bne 2b
+END_FTR_SECTION_IFSET(CPU_FTR_L2CSR|CPU_FTR_CAN_NAP)
+1:
+ /* Go to NAP or DOZE now */
+ mfspr r4,SPRN_HID0
+ rlwinm r4,r4,0,~(HID0_DOZE|HID0_NAP|HID0_SLEEP)
+ or r4,r4,r3
+ isync
+ mtspr SPRN_HID0,r4
+ isync
+
+ mfmsr r7
+ oris r7,r7,MSR_WE@h
+ ori r7,r7,MSR_EE
+ msync
+ mtmsr r7
+ isync
+2: b 2b
+
+/*
+ * Return from NAP/DOZE mode, restore some CPU specific registers,
+ * r2 containing physical address of current.
+ * r11 points to the exception frame (physical address).
+ * We have to preserve r10.
+ */
+_GLOBAL(power_save_ppc32_restore)
+ lwz r9,_LINK(r11) /* interrupted in e500_idle */
+ stw r9,_NIP(r11) /* make it do a blr */
+
+#ifdef CONFIG_SMP
+ mfspr r12,SPRN_SPRG3
+ lwz r11,TI_CPU(r12) /* get cpu number * 4 */
+ slwi r11,r11,2
+#else
+ li r11,0
+#endif
+ b transfer_to_handler_cont
#include <asm/cacheflush.h>
#include <asm/sstep.h>
#include <asm/uaccess.h>
+#include <asm/system.h>
+
+#ifdef CONFIG_BOOKE
+#define MSR_SINGLESTEP (MSR_DE)
+#else
+#define MSR_SINGLESTEP (MSR_SE)
+#endif
DEFINE_PER_CPU(struct kprobe *, current_kprobe) = NULL;
DEFINE_PER_CPU(struct kprobe_ctlblk, kprobe_ctlblk);
ret = -EINVAL;
}
- /* insn must be on a special executable page on ppc64 */
+ /* insn must be on a special executable page on ppc64. This is
+ * not explicitly required on ppc32 (right now), but it doesn't hurt */
if (!ret) {
p->ainsn.insn = get_insn_slot();
if (!p->ainsn.insn)
static void __kprobes prepare_singlestep(struct kprobe *p, struct pt_regs *regs)
{
- regs->msr |= MSR_SE;
+ /* We turn off async exceptions to ensure that the single step will
+ * be for the instruction we have the kprobe on, if we dont its
+ * possible we'd get the single step reported for an exception handler
+ * like Decrementer or External Interrupt */
+ regs->msr &= ~MSR_EE;
+ regs->msr |= MSR_SINGLESTEP;
+#ifdef CONFIG_BOOKE
+ regs->msr &= ~MSR_CE;
+ mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) | DBCR0_IC | DBCR0_IDM);
+#endif
/*
* On powerpc we should single step on the original
kprobe_opcode_t insn = *p->ainsn.insn;
if (kcb->kprobe_status == KPROBE_HIT_SS &&
is_trap(insn)) {
- regs->msr &= ~MSR_SE;
+ /* Turn off 'trace' bits */
+ regs->msr &= ~MSR_SINGLESTEP;
regs->msr |= kcb->kprobe_saved_msr;
goto no_kprobe;
}
if (!cur)
return 0;
+ /* make sure we got here for instruction we have a kprobe on */
+ if (((unsigned long)cur->ainsn.insn + 4) != regs->nip)
+ return 0;
+
if ((kcb->kprobe_status != KPROBE_REENTER) && cur->post_handler) {
kcb->kprobe_status = KPROBE_HIT_SSDONE;
cur->post_handler(cur, regs, 0);
/*
* if somebody else is singlestepping across a probe point, msr
- * will have SE set, in which case, continue the remaining processing
+ * will have DE/SE set, in which case, continue the remaining processing
* of do_debug, as if this is not a probe hit.
*/
- if (regs->msr & MSR_SE)
+ if (regs->msr & MSR_SINGLESTEP)
return 0;
return 1;
* normal page fault.
*/
regs->nip = (unsigned long)cur->addr;
- regs->msr &= ~MSR_SE;
+ regs->msr &= ~MSR_SINGLESTEP; /* Turn off 'trace' bits */
regs->msr |= kcb->kprobe_saved_msr;
if (kcb->kprobe_status == KPROBE_REENTER)
restore_previous_kprobe(kcb);
*
* flush_icache_range(unsigned long start, unsigned long stop)
*/
-_GLOBAL(__flush_icache_range)
+_KPROBE(__flush_icache_range)
BEGIN_FTR_SECTION
blr /* for 601, do nothing */
END_FTR_SECTION_IFSET(CPU_FTR_COHERENT_ICACHE)
ppc_md.power_save = ppc6xx_idle;
#endif
+#ifdef CONFIG_E500
+ if (cpu_has_feature(CPU_FTR_CAN_DOZE) ||
+ cpu_has_feature(CPU_FTR_CAN_NAP))
+ ppc_md.power_save = e500_idle;
+#endif
if (ppc_md.progress)
ppc_md.progress("id mach(): done", 0x200);
}
#if defined(CONFIG_40x) || defined(CONFIG_BOOKE)
-void DebugException(struct pt_regs *regs, unsigned long debug_status)
+void __kprobes DebugException(struct pt_regs *regs, unsigned long debug_status)
{
if (debug_status & DBSR_IC) { /* instruction completion */
regs->msr &= ~MSR_DE;
+
+ /* Disable instruction completion */
+ mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~DBCR0_IC);
+ /* Clear the instruction completion event */
+ mtspr(SPRN_DBSR, DBSR_IC);
+
+ if (notify_die(DIE_SSTEP, "single_step", regs, 5,
+ 5, SIGTRAP) == NOTIFY_STOP) {
+ return;
+ }
+
+ if (debugger_sstep(regs))
+ return;
+
if (user_mode(regs)) {
current->thread.dbcr0 &= ~DBCR0_IC;
- } else {
- /* Disable instruction completion */
- mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~DBCR0_IC);
- /* Clear the instruction completion event */
- mtspr(SPRN_DBSR, DBSR_IC);
- if (debugger_sstep(regs))
- return;
}
- _exception(SIGTRAP, regs, TRAP_TRACE, 0);
+
+ _exception(SIGTRAP, regs, TRAP_TRACE, regs->nip);
}
}
#endif /* CONFIG_4xx || CONFIG_BOOKE */
help
This option enables support for the MPC836x MDS Processor Board.
+config MPC836x_RDK
+ bool "Freescale/Logic MPC836x RDK"
+ select DEFAULT_UIMAGE
+ select QUICC_ENGINE
+ select QE_GPIO
+ select FSL_GTM
+ select FSL_LBC
+ help
+ This option enables support for the MPC836x RDK Processor Board,
+ also known as ZOOM PowerQUICC Kit.
+
config MPC837x_MDS
bool "Freescale MPC837x MDS"
select DEFAULT_UIMAGE
obj-$(CONFIG_MPC834x_MDS) += mpc834x_mds.o
obj-$(CONFIG_MPC834x_ITX) += mpc834x_itx.o
obj-$(CONFIG_MPC836x_MDS) += mpc836x_mds.o
+obj-$(CONFIG_MPC836x_RDK) += mpc836x_rdk.o
obj-$(CONFIG_MPC832x_MDS) += mpc832x_mds.o
obj-$(CONFIG_MPC837x_MDS) += mpc837x_mds.o
obj-$(CONFIG_SBC834x) += sbc834x.o
--- /dev/null
+/*
+ * MPC8360E-RDK board file.
+ *
+ * Copyright (c) 2006 Freescale Semicondutor, Inc.
+ * Copyright (c) 2007-2008 MontaVista Software, Inc.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/of_platform.h>
+#include <linux/io.h>
+#include <asm/prom.h>
+#include <asm/time.h>
+#include <asm/ipic.h>
+#include <asm/udbg.h>
+#include <asm/qe.h>
+#include <asm/qe_ic.h>
+#include <sysdev/fsl_soc.h>
+
+#include "mpc83xx.h"
+
+static struct of_device_id __initdata mpc836x_rdk_ids[] = {
+ { .compatible = "simple-bus", },
+ {},
+};
+
+static int __init mpc836x_rdk_declare_of_platform_devices(void)
+{
+ return of_platform_bus_probe(NULL, mpc836x_rdk_ids, NULL);
+}
+machine_device_initcall(mpc836x_rdk, mpc836x_rdk_declare_of_platform_devices);
+
+static void __init mpc836x_rdk_setup_arch(void)
+{
+#ifdef CONFIG_PCI
+ struct device_node *np;
+#endif
+
+ if (ppc_md.progress)
+ ppc_md.progress("mpc836x_rdk_setup_arch()", 0);
+
+#ifdef CONFIG_PCI
+ for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
+ mpc83xx_add_bridge(np);
+#endif
+
+ qe_reset();
+}
+
+static void __init mpc836x_rdk_init_IRQ(void)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,ipic");
+ if (!np)
+ return;
+
+ ipic_init(np, 0);
+
+ /*
+ * Initialize the default interrupt mapping priorities,
+ * in case the boot rom changed something on us.
+ */
+ ipic_set_default_priority();
+ of_node_put(np);
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
+ if (!np)
+ return;
+
+ qe_ic_init(np, 0, qe_ic_cascade_low_ipic, qe_ic_cascade_high_ipic);
+ of_node_put(np);
+}
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened.
+ */
+static int __init mpc836x_rdk_probe(void)
+{
+ unsigned long root = of_get_flat_dt_root();
+
+ return of_flat_dt_is_compatible(root, "fsl,mpc8360rdk");
+}
+
+define_machine(mpc836x_rdk) {
+ .name = "MPC836x RDK",
+ .probe = mpc836x_rdk_probe,
+ .setup_arch = mpc836x_rdk_setup_arch,
+ .init_IRQ = mpc836x_rdk_init_IRQ,
+ .get_irq = ipic_get_irq,
+ .restart = mpc83xx_restart,
+ .time_init = mpc83xx_time_init,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
select TQM85xx
select CPM2
+config TQM8548
+ bool "TQ Components TQM8548"
+ help
+ This option enables support for the TQ Components TQM8548 board.
+ select DEFAULT_UIMAGE
+ select PPC_CPM_NEW_BINDING
+ select TQM85xx
+
config TQM8555
bool "TQ Components TQM8555"
help
{3, 31, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
/* SCC2 */
+ {2, 12, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
+ {2, 13, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{3, 26, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{3, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{3, 28, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{1, 4, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{1, 5, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{1, 6, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
- {1, 7, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{1, 8, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{1, 9, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{1, 10, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{1, 15, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
{1, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
{1, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY},
- {2, 16, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* CLK16 */
- {2, 17, CPM_PIN_INPUT | CPM_PIN_SECONDARY}, /* CLK15 */
+ {2, 16, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK16 */
+ {2, 17, CPM_PIN_INPUT | CPM_PIN_PRIMARY}, /* CLK15 */
+ {2, 27, CPM_PIN_OUTPUT | CPM_PIN_PRIMARY},
};
static void __init init_ioports(void)
#endif
#ifdef CONFIG_PCI
- for_each_compatible_node(np, "pci", "fsl,mpc8540-pci")
- fsl_add_bridge(np, 1);
+ for_each_node_by_type(np, "pci") {
+ if (of_device_is_compatible(np, "fsl,mpc8540-pci") ||
+ of_device_is_compatible(np, "fsl,mpc8548-pcie")) {
+ struct resource rsrc;
+ if (!of_address_to_resource(np, 0, &rsrc)) {
+ if ((rsrc.start & 0xfffff) == 0x8000)
+ fsl_add_bridge(np, 1);
+ else
+ fsl_add_bridge(np, 0);
+ }
+ }
+ }
#endif
}
{
unsigned long root = of_get_flat_dt_root();
- if ((of_flat_dt_is_compatible(root, "tqm,8540")) ||
- (of_flat_dt_is_compatible(root, "tqm,8541")) ||
- (of_flat_dt_is_compatible(root, "tqm,8555")) ||
- (of_flat_dt_is_compatible(root, "tqm,8560")))
+ if ((of_flat_dt_is_compatible(root, "tqc,tqm8540")) ||
+ (of_flat_dt_is_compatible(root, "tqc,tqm8541")) ||
+ (of_flat_dt_is_compatible(root, "tqc,tqm8548")) ||
+ (of_flat_dt_is_compatible(root, "tqc,tqm8555")) ||
+ (of_flat_dt_is_compatible(root, "tqc,tqm8560")))
return 1;
return 0;
select FSL_EMB_PERFMON
bool
+config PPC_E500MC
+ bool "e500mc Support"
+ select PPC_FPU
+ depends on E500
+
config PPC_FPU
bool
default y if PPC64
config SPE
bool "SPE Support"
- depends on E200 || E500
+ depends on E200 || (E500 && !PPC_E500MC)
default y
---help---
This option enables kernel support for the Signal Processing
obj-$(CONFIG_FSL_SOC) += fsl_soc.o
obj-$(CONFIG_FSL_PCI) += fsl_pci.o $(fsl-msi-obj-y)
obj-$(CONFIG_FSL_LBC) += fsl_lbc.o
+obj-$(CONFIG_FSL_GTM) += fsl_gtm.o
obj-$(CONFIG_RAPIDIO) += fsl_rio.o
obj-$(CONFIG_TSI108_BRIDGE) += tsi108_pci.o tsi108_dev.o
obj-$(CONFIG_QUICC_ENGINE) += qe_lib/
ifeq ($(ARCH),powerpc)
obj-$(CONFIG_CPM) += cpm_common.o
obj-$(CONFIG_CPM2) += cpm2.o cpm2_pic.o
+obj-$(CONFIG_QUICC_ENGINE) += cpm_common.o
obj-$(CONFIG_PPC_DCR) += dcr.o
obj-$(CONFIG_8xx) += mpc8xx_pic.o cpm1.o
obj-$(CONFIG_UCODE_PATCH) += micropatch.o
np = of_find_compatible_node(NULL, NULL, "fsl,cpm-muram-data");
if (!np) {
- printk(KERN_ERR "Cannot find CPM muram data node");
- ret = -ENODEV;
- goto out;
+ /* try legacy bindings */
+ np = of_find_node_by_name(NULL, "data-only");
+ if (!np) {
+ printk(KERN_ERR "Cannot find CPM muram data node");
+ ret = -ENODEV;
+ goto out;
+ }
}
muram_pbase = of_translate_address(np, zero);
}
EXPORT_SYMBOL(cpm_muram_addr);
+unsigned long cpm_muram_offset(void __iomem *addr)
+{
+ return addr - (void __iomem *)muram_vbase;
+}
+EXPORT_SYMBOL(cpm_muram_offset);
+
/**
* cpm_muram_dma - turn a muram virtual address into a DMA address
* @offset: virtual address from cpm_muram_addr() to convert
--- /dev/null
+/*
+ * Freescale General-purpose Timers Module
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ * Shlomi Gridish <gridish@freescale.com>
+ * Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/spinlock.h>
+#include <linux/bitops.h>
+#include <asm/fsl_gtm.h>
+
+#define GTCFR_STP(x) ((x) & 1 ? 1 << 5 : 1 << 1)
+#define GTCFR_RST(x) ((x) & 1 ? 1 << 4 : 1 << 0)
+
+#define GTMDR_ICLK_MASK (3 << 1)
+#define GTMDR_ICLK_ICAS (0 << 1)
+#define GTMDR_ICLK_ICLK (1 << 1)
+#define GTMDR_ICLK_SLGO (2 << 1)
+#define GTMDR_FRR (1 << 3)
+#define GTMDR_ORI (1 << 4)
+#define GTMDR_SPS(x) ((x) << 8)
+
+struct gtm_timers_regs {
+ u8 gtcfr1; /* Timer 1, Timer 2 global config register */
+ u8 res0[0x3];
+ u8 gtcfr2; /* Timer 3, timer 4 global config register */
+ u8 res1[0xB];
+ __be16 gtmdr1; /* Timer 1 mode register */
+ __be16 gtmdr2; /* Timer 2 mode register */
+ __be16 gtrfr1; /* Timer 1 reference register */
+ __be16 gtrfr2; /* Timer 2 reference register */
+ __be16 gtcpr1; /* Timer 1 capture register */
+ __be16 gtcpr2; /* Timer 2 capture register */
+ __be16 gtcnr1; /* Timer 1 counter */
+ __be16 gtcnr2; /* Timer 2 counter */
+ __be16 gtmdr3; /* Timer 3 mode register */
+ __be16 gtmdr4; /* Timer 4 mode register */
+ __be16 gtrfr3; /* Timer 3 reference register */
+ __be16 gtrfr4; /* Timer 4 reference register */
+ __be16 gtcpr3; /* Timer 3 capture register */
+ __be16 gtcpr4; /* Timer 4 capture register */
+ __be16 gtcnr3; /* Timer 3 counter */
+ __be16 gtcnr4; /* Timer 4 counter */
+ __be16 gtevr1; /* Timer 1 event register */
+ __be16 gtevr2; /* Timer 2 event register */
+ __be16 gtevr3; /* Timer 3 event register */
+ __be16 gtevr4; /* Timer 4 event register */
+ __be16 gtpsr1; /* Timer 1 prescale register */
+ __be16 gtpsr2; /* Timer 2 prescale register */
+ __be16 gtpsr3; /* Timer 3 prescale register */
+ __be16 gtpsr4; /* Timer 4 prescale register */
+ u8 res2[0x40];
+} __attribute__ ((packed));
+
+struct gtm {
+ unsigned int clock;
+ struct gtm_timers_regs __iomem *regs;
+ struct gtm_timer timers[4];
+ spinlock_t lock;
+ struct list_head list_node;
+};
+
+static LIST_HEAD(gtms);
+
+/**
+ * gtm_get_timer - request GTM timer to use it with the rest of GTM API
+ * Context: non-IRQ
+ *
+ * This function reserves GTM timer for later use. It returns gtm_timer
+ * structure to use with the rest of GTM API, you should use timer->irq
+ * to manage timer interrupt.
+ */
+struct gtm_timer *gtm_get_timer16(void)
+{
+ struct gtm *gtm = NULL;
+ int i;
+
+ list_for_each_entry(gtm, >ms, list_node) {
+ spin_lock_irq(>m->lock);
+
+ for (i = 0; i < ARRAY_SIZE(gtm->timers); i++) {
+ if (!gtm->timers[i].requested) {
+ gtm->timers[i].requested = true;
+ spin_unlock_irq(>m->lock);
+ return >m->timers[i];
+ }
+ }
+
+ spin_unlock_irq(>m->lock);
+ }
+
+ if (gtm)
+ return ERR_PTR(-EBUSY);
+ return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL(gtm_get_timer16);
+
+/**
+ * gtm_get_specific_timer - request specific GTM timer
+ * @gtm: specific GTM, pass here GTM's device_node->data
+ * @timer: specific timer number, Timer1 is 0.
+ * Context: non-IRQ
+ *
+ * This function reserves GTM timer for later use. It returns gtm_timer
+ * structure to use with the rest of GTM API, you should use timer->irq
+ * to manage timer interrupt.
+ */
+struct gtm_timer *gtm_get_specific_timer16(struct gtm *gtm,
+ unsigned int timer)
+{
+ struct gtm_timer *ret = ERR_PTR(-EBUSY);
+
+ if (timer > 3)
+ return ERR_PTR(-EINVAL);
+
+ spin_lock_irq(>m->lock);
+
+ if (gtm->timers[timer].requested)
+ goto out;
+
+ ret = >m->timers[timer];
+ ret->requested = true;
+
+out:
+ spin_unlock_irq(>m->lock);
+ return ret;
+}
+EXPORT_SYMBOL(gtm_get_specific_timer16);
+
+/**
+ * gtm_put_timer16 - release 16 bits GTM timer
+ * @tmr: pointer to the gtm_timer structure obtained from gtm_get_timer
+ * Context: any
+ *
+ * This function releases GTM timer so others may request it.
+ */
+void gtm_put_timer16(struct gtm_timer *tmr)
+{
+ gtm_stop_timer16(tmr);
+
+ spin_lock_irq(&tmr->gtm->lock);
+ tmr->requested = false;
+ spin_unlock_irq(&tmr->gtm->lock);
+}
+EXPORT_SYMBOL(gtm_put_timer16);
+
+/*
+ * This is back-end for the exported functions, it's used to reset single
+ * timer in reference mode.
+ */
+static int gtm_set_ref_timer16(struct gtm_timer *tmr, int frequency,
+ int reference_value, bool free_run)
+{
+ struct gtm *gtm = tmr->gtm;
+ int num = tmr - >m->timers[0];
+ unsigned int prescaler;
+ u8 iclk = GTMDR_ICLK_ICLK;
+ u8 psr;
+ u8 sps;
+ unsigned long flags;
+ int max_prescaler = 256 * 256 * 16;
+
+ /* CPM2 doesn't have primary prescaler */
+ if (!tmr->gtpsr)
+ max_prescaler /= 256;
+
+ prescaler = gtm->clock / frequency;
+ /*
+ * We have two 8 bit prescalers -- primary and secondary (psr, sps),
+ * plus "slow go" mode (clk / 16). So, total prescale value is
+ * 16 * (psr + 1) * (sps + 1). Though, for CPM2 GTMs we losing psr.
+ */
+ if (prescaler > max_prescaler)
+ return -EINVAL;
+
+ if (prescaler > max_prescaler / 16) {
+ iclk = GTMDR_ICLK_SLGO;
+ prescaler /= 16;
+ }
+
+ if (prescaler <= 256) {
+ psr = 0;
+ sps = prescaler - 1;
+ } else {
+ psr = 256 - 1;
+ sps = prescaler / 256 - 1;
+ }
+
+ spin_lock_irqsave(>m->lock, flags);
+
+ /*
+ * Properly reset timers: stop, reset, set up prescalers, reference
+ * value and clear event register.
+ */
+ clrsetbits_8(tmr->gtcfr, ~(GTCFR_STP(num) | GTCFR_RST(num)),
+ GTCFR_STP(num) | GTCFR_RST(num));
+
+ setbits8(tmr->gtcfr, GTCFR_STP(num));
+
+ if (tmr->gtpsr)
+ out_be16(tmr->gtpsr, psr);
+ clrsetbits_be16(tmr->gtmdr, 0xFFFF, iclk | GTMDR_SPS(sps) |
+ GTMDR_ORI | (free_run ? GTMDR_FRR : 0));
+ out_be16(tmr->gtcnr, 0);
+ out_be16(tmr->gtrfr, reference_value);
+ out_be16(tmr->gtevr, 0xFFFF);
+
+ /* Let it be. */
+ clrbits8(tmr->gtcfr, GTCFR_STP(num));
+
+ spin_unlock_irqrestore(>m->lock, flags);
+
+ return 0;
+}
+
+/**
+ * gtm_set_timer16 - (re)set 16 bit timer with arbitrary precision
+ * @tmr: pointer to the gtm_timer structure obtained from gtm_get_timer
+ * @usec: timer interval in microseconds
+ * @reload: if set, the timer will reset upon expiry rather than
+ * continue running free.
+ * Context: any
+ *
+ * This function (re)sets the GTM timer so that it counts up to the requested
+ * interval value, and fires the interrupt when the value is reached. This
+ * function will reduce the precision of the timer as needed in order for the
+ * requested timeout to fit in a 16-bit register.
+ */
+int gtm_set_timer16(struct gtm_timer *tmr, unsigned long usec, bool reload)
+{
+ /* quite obvious, frequency which is enough for µSec precision */
+ int freq = 1000000;
+ unsigned int bit;
+
+ bit = fls_long(usec);
+ if (bit > 15) {
+ freq >>= bit - 15;
+ usec >>= bit - 15;
+ }
+
+ if (!freq)
+ return -EINVAL;
+
+ return gtm_set_ref_timer16(tmr, freq, usec, reload);
+}
+EXPORT_SYMBOL(gtm_set_timer16);
+
+/**
+ * gtm_set_exact_utimer16 - (re)set 16 bits timer
+ * @tmr: pointer to the gtm_timer structure obtained from gtm_get_timer
+ * @usec: timer interval in microseconds
+ * @reload: if set, the timer will reset upon expiry rather than
+ * continue running free.
+ * Context: any
+ *
+ * This function (re)sets GTM timer so that it counts up to the requested
+ * interval value, and fires the interrupt when the value is reached. If reload
+ * flag was set, timer will also reset itself upon reference value, otherwise
+ * it continues to increment.
+ *
+ * The _exact_ bit in the function name states that this function will not
+ * crop precision of the "usec" argument, thus usec is limited to 16 bits
+ * (single timer width).
+ */
+int gtm_set_exact_timer16(struct gtm_timer *tmr, u16 usec, bool reload)
+{
+ /* quite obvious, frequency which is enough for µSec precision */
+ const int freq = 1000000;
+
+ /*
+ * We can lower the frequency (and probably power consumption) by
+ * dividing both frequency and usec by 2 until there is no remainder.
+ * But we won't bother with this unless savings are measured, so just
+ * run the timer as is.
+ */
+
+ return gtm_set_ref_timer16(tmr, freq, usec, reload);
+}
+EXPORT_SYMBOL(gtm_set_exact_timer16);
+
+/**
+ * gtm_stop_timer16 - stop single timer
+ * @tmr: pointer to the gtm_timer structure obtained from gtm_get_timer
+ * Context: any
+ *
+ * This function simply stops the GTM timer.
+ */
+void gtm_stop_timer16(struct gtm_timer *tmr)
+{
+ struct gtm *gtm = tmr->gtm;
+ int num = tmr - >m->timers[0];
+ unsigned long flags;
+
+ spin_lock_irqsave(>m->lock, flags);
+
+ setbits8(tmr->gtcfr, GTCFR_STP(num));
+ out_be16(tmr->gtevr, 0xFFFF);
+
+ spin_unlock_irqrestore(>m->lock, flags);
+}
+EXPORT_SYMBOL(gtm_stop_timer16);
+
+/**
+ * gtm_ack_timer16 - acknowledge timer event (free-run timers only)
+ * @tmr: pointer to the gtm_timer structure obtained from gtm_get_timer
+ * @events: events mask to ack
+ * Context: any
+ *
+ * Thus function used to acknowledge timer interrupt event, use it inside the
+ * interrupt handler.
+ */
+void gtm_ack_timer16(struct gtm_timer *tmr, u16 events)
+{
+ out_be16(tmr->gtevr, events);
+}
+EXPORT_SYMBOL(gtm_ack_timer16);
+
+static void __init gtm_set_shortcuts(struct device_node *np,
+ struct gtm_timer *timers,
+ struct gtm_timers_regs __iomem *regs)
+{
+ /*
+ * Yeah, I don't like this either, but timers' registers a bit messed,
+ * so we have to provide shortcuts to write timer independent code.
+ * Alternative option is to create gt*() accessors, but that will be
+ * even uglier and cryptic.
+ */
+ timers[0].gtcfr = ®s->gtcfr1;
+ timers[0].gtmdr = ®s->gtmdr1;
+ timers[0].gtcnr = ®s->gtcnr1;
+ timers[0].gtrfr = ®s->gtrfr1;
+ timers[0].gtevr = ®s->gtevr1;
+
+ timers[1].gtcfr = ®s->gtcfr1;
+ timers[1].gtmdr = ®s->gtmdr2;
+ timers[1].gtcnr = ®s->gtcnr2;
+ timers[1].gtrfr = ®s->gtrfr2;
+ timers[1].gtevr = ®s->gtevr2;
+
+ timers[2].gtcfr = ®s->gtcfr2;
+ timers[2].gtmdr = ®s->gtmdr3;
+ timers[2].gtcnr = ®s->gtcnr3;
+ timers[2].gtrfr = ®s->gtrfr3;
+ timers[2].gtevr = ®s->gtevr3;
+
+ timers[3].gtcfr = ®s->gtcfr2;
+ timers[3].gtmdr = ®s->gtmdr4;
+ timers[3].gtcnr = ®s->gtcnr4;
+ timers[3].gtrfr = ®s->gtrfr4;
+ timers[3].gtevr = ®s->gtevr4;
+
+ /* CPM2 doesn't have primary prescaler */
+ if (!of_device_is_compatible(np, "fsl,cpm2-gtm")) {
+ timers[0].gtpsr = ®s->gtpsr1;
+ timers[1].gtpsr = ®s->gtpsr2;
+ timers[2].gtpsr = ®s->gtpsr3;
+ timers[3].gtpsr = ®s->gtpsr4;
+ }
+}
+
+static int __init fsl_gtm_init(void)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, "fsl,gtm") {
+ int i;
+ struct gtm *gtm;
+ const u32 *clock;
+ int size;
+
+ gtm = kzalloc(sizeof(*gtm), GFP_KERNEL);
+ if (!gtm) {
+ pr_err("%s: unable to allocate memory\n",
+ np->full_name);
+ continue;
+ }
+
+ spin_lock_init(>m->lock);
+
+ clock = of_get_property(np, "clock-frequency", &size);
+ if (!clock || size != sizeof(*clock)) {
+ pr_err("%s: no clock-frequency\n", np->full_name);
+ goto err;
+ }
+ gtm->clock = *clock;
+
+ for (i = 0; i < ARRAY_SIZE(gtm->timers); i++) {
+ int ret;
+ struct resource irq;
+
+ ret = of_irq_to_resource(np, i, &irq);
+ if (ret == NO_IRQ) {
+ pr_err("%s: not enough interrupts specified\n",
+ np->full_name);
+ goto err;
+ }
+ gtm->timers[i].irq = irq.start;
+ gtm->timers[i].gtm = gtm;
+ }
+
+ gtm->regs = of_iomap(np, 0);
+ if (!gtm->regs) {
+ pr_err("%s: unable to iomap registers\n",
+ np->full_name);
+ goto err;
+ }
+
+ gtm_set_shortcuts(np, gtm->timers, gtm->regs);
+ list_add(>m->list_node, >ms);
+
+ /* We don't want to lose the node and its ->data */
+ np->data = gtm;
+ of_node_get(np);
+
+ continue;
+err:
+ kfree(gtm);
+ }
+ return 0;
+}
+arch_initcall(fsl_gtm_init);
bool
default y if UCC_FAST || UCC_SLOW
+config QE_USB
+ bool
+ help
+ QE USB Host Controller support
+
+config QE_GPIO
+ bool "QE GPIO support"
+ depends on QUICC_ENGINE
+ select GENERIC_GPIO
+ select HAVE_GPIO_LIB
+ help
+ Say Y here if you're going to use hardware that connects to the
+ QE GPIOs.
obj-$(CONFIG_UCC) += ucc.o
obj-$(CONFIG_UCC_SLOW) += ucc_slow.o
obj-$(CONFIG_UCC_FAST) += ucc_fast.o
+obj-$(CONFIG_QE_USB) += usb.o
+obj-$(CONFIG_QE_GPIO) += gpio.o
--- /dev/null
+/*
+ * QUICC Engine GPIOs
+ *
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <asm/qe.h>
+
+struct qe_gpio_chip {
+ struct of_mm_gpio_chip mm_gc;
+ spinlock_t lock;
+
+ /* shadowed data register to clear/set bits safely */
+ u32 cpdata;
+};
+
+static inline struct qe_gpio_chip *
+to_qe_gpio_chip(struct of_mm_gpio_chip *mm_gc)
+{
+ return container_of(mm_gc, struct qe_gpio_chip, mm_gc);
+}
+
+static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+ struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+ struct qe_pio_regs __iomem *regs = mm_gc->regs;
+
+ qe_gc->cpdata = in_be32(®s->cpdata);
+}
+
+static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct qe_pio_regs __iomem *regs = mm_gc->regs;
+ u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
+
+ return in_be32(®s->cpdata) & pin_mask;
+}
+
+static void qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+ struct qe_pio_regs __iomem *regs = mm_gc->regs;
+ unsigned long flags;
+ u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
+
+ spin_lock_irqsave(&qe_gc->lock, flags);
+
+ if (val)
+ qe_gc->cpdata |= pin_mask;
+ else
+ qe_gc->cpdata &= ~pin_mask;
+
+ out_be32(®s->cpdata, qe_gc->cpdata);
+
+ spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+
+static int qe_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&qe_gc->lock, flags);
+
+ __par_io_config_pin(mm_gc->regs, gpio, QE_PIO_DIR_IN, 0, 0, 0);
+
+ spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+ return 0;
+}
+
+static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+ struct qe_gpio_chip *qe_gc = to_qe_gpio_chip(mm_gc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&qe_gc->lock, flags);
+
+ __par_io_config_pin(mm_gc->regs, gpio, QE_PIO_DIR_OUT, 0, 0, 0);
+
+ spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+ qe_gpio_set(gc, gpio, val);
+
+ return 0;
+}
+
+static int __init qe_add_gpiochips(void)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, "fsl,mpc8323-qe-pario-bank") {
+ int ret;
+ struct qe_gpio_chip *qe_gc;
+ struct of_mm_gpio_chip *mm_gc;
+ struct of_gpio_chip *of_gc;
+ struct gpio_chip *gc;
+
+ qe_gc = kzalloc(sizeof(*qe_gc), GFP_KERNEL);
+ if (!qe_gc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ spin_lock_init(&qe_gc->lock);
+
+ mm_gc = &qe_gc->mm_gc;
+ of_gc = &mm_gc->of_gc;
+ gc = &of_gc->gc;
+
+ mm_gc->save_regs = qe_gpio_save_regs;
+ of_gc->gpio_cells = 2;
+ gc->ngpio = QE_PIO_PINS;
+ gc->direction_input = qe_gpio_dir_in;
+ gc->direction_output = qe_gpio_dir_out;
+ gc->get = qe_gpio_get;
+ gc->set = qe_gpio_set;
+
+ ret = of_mm_gpiochip_add(np, mm_gc);
+ if (ret)
+ goto err;
+ continue;
+err:
+ pr_err("%s: registration failed with status %d\n",
+ np->full_name, ret);
+ kfree(qe_gc);
+ /* try others anyway */
+ }
+ return 0;
+}
+arch_initcall(qe_add_gpiochips);
#include <asm/rheap.h>
static void qe_snums_init(void);
-static void qe_muram_init(void);
static int qe_sdma_init(void);
static DEFINE_SPINLOCK(qe_lock);
EXPORT_SYMBOL(get_qe_base);
-void qe_reset(void)
+void __init qe_reset(void)
{
if (qe_immr == NULL)
qe_immr = ioremap(get_qe_base(), QE_IMMAP_SIZE);
return 0;
}
-/*
- * muram_alloc / muram_free bits.
- */
-static DEFINE_SPINLOCK(qe_muram_lock);
-
-/* 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up... */
-static rh_block_t qe_boot_muram_rh_block[16];
-static rh_info_t qe_muram_info;
-
-static void qe_muram_init(void)
-{
- struct device_node *np;
- const u32 *address;
- u64 size;
- unsigned int flags;
-
- /* initialize the info header */
- rh_init(&qe_muram_info, 1,
- sizeof(qe_boot_muram_rh_block) /
- sizeof(qe_boot_muram_rh_block[0]), qe_boot_muram_rh_block);
-
- /* Attach the usable muram area */
- /* XXX: This is a subset of the available muram. It
- * varies with the processor and the microcode patches activated.
- */
- np = of_find_compatible_node(NULL, NULL, "fsl,qe-muram-data");
- if (!np) {
- np = of_find_node_by_name(NULL, "data-only");
- if (!np) {
- WARN_ON(1);
- return;
- }
- }
-
- address = of_get_address(np, 0, &size, &flags);
- WARN_ON(!address);
-
- of_node_put(np);
- if (address)
- rh_attach_region(&qe_muram_info, *address, (int)size);
-}
-
-/* This function returns an index into the MURAM area.
- */
-unsigned long qe_muram_alloc(int size, int align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&qe_muram_lock, flags);
- start = rh_alloc_align(&qe_muram_info, size, align, "QE");
- spin_unlock_irqrestore(&qe_muram_lock, flags);
-
- return start;
-}
-EXPORT_SYMBOL(qe_muram_alloc);
-
-int qe_muram_free(unsigned long offset)
-{
- int ret;
- unsigned long flags;
-
- spin_lock_irqsave(&qe_muram_lock, flags);
- ret = rh_free(&qe_muram_info, offset);
- spin_unlock_irqrestore(&qe_muram_lock, flags);
-
- return ret;
-}
-EXPORT_SYMBOL(qe_muram_free);
-
-/* not sure if this is ever needed */
-unsigned long qe_muram_alloc_fixed(unsigned long offset, int size)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&qe_muram_lock, flags);
- start = rh_alloc_fixed(&qe_muram_info, offset, size, "commproc");
- spin_unlock_irqrestore(&qe_muram_lock, flags);
-
- return start;
-}
-EXPORT_SYMBOL(qe_muram_alloc_fixed);
-
-void qe_muram_dump(void)
-{
- rh_dump(&qe_muram_info);
-}
-EXPORT_SYMBOL(qe_muram_dump);
-
/* The maximum number of RISCs we support */
#define MAX_QE_RISC 2
#undef DEBUG
-#define NUM_OF_PINS 32
-
-struct port_regs {
- __be32 cpodr; /* Open drain register */
- __be32 cpdata; /* Data register */
- __be32 cpdir1; /* Direction register */
- __be32 cpdir2; /* Direction register */
- __be32 cppar1; /* Pin assignment register */
- __be32 cppar2; /* Pin assignment register */
-#ifdef CONFIG_PPC_85xx
- u8 pad[8];
-#endif
-};
-
-static struct port_regs __iomem *par_io;
+static struct qe_pio_regs __iomem *par_io;
static int num_par_io_ports = 0;
int par_io_init(struct device_node *np)
return 0;
}
-int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
- int assignment, int has_irq)
+void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin, int dir,
+ int open_drain, int assignment, int has_irq)
{
- u32 pin_mask1bit, pin_mask2bits, new_mask2bits, tmp_val;
-
- if (!par_io)
- return -1;
+ u32 pin_mask1bit;
+ u32 pin_mask2bits;
+ u32 new_mask2bits;
+ u32 tmp_val;
/* calculate pin location for single and 2 bits information */
- pin_mask1bit = (u32) (1 << (NUM_OF_PINS - (pin + 1)));
+ pin_mask1bit = (u32) (1 << (QE_PIO_PINS - (pin + 1)));
/* Set open drain, if required */
- tmp_val = in_be32(&par_io[port].cpodr);
+ tmp_val = in_be32(&par_io->cpodr);
if (open_drain)
- out_be32(&par_io[port].cpodr, pin_mask1bit | tmp_val);
+ out_be32(&par_io->cpodr, pin_mask1bit | tmp_val);
else
- out_be32(&par_io[port].cpodr, ~pin_mask1bit & tmp_val);
+ out_be32(&par_io->cpodr, ~pin_mask1bit & tmp_val);
/* define direction */
- tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
- in_be32(&par_io[port].cpdir2) :
- in_be32(&par_io[port].cpdir1);
+ tmp_val = (pin > (QE_PIO_PINS / 2) - 1) ?
+ in_be32(&par_io->cpdir2) :
+ in_be32(&par_io->cpdir1);
/* get all bits mask for 2 bit per port */
- pin_mask2bits = (u32) (0x3 << (NUM_OF_PINS -
- (pin % (NUM_OF_PINS / 2) + 1) * 2));
+ pin_mask2bits = (u32) (0x3 << (QE_PIO_PINS -
+ (pin % (QE_PIO_PINS / 2) + 1) * 2));
/* Get the final mask we need for the right definition */
- new_mask2bits = (u32) (dir << (NUM_OF_PINS -
- (pin % (NUM_OF_PINS / 2) + 1) * 2));
+ new_mask2bits = (u32) (dir << (QE_PIO_PINS -
+ (pin % (QE_PIO_PINS / 2) + 1) * 2));
/* clear and set 2 bits mask */
- if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io[port].cpdir2,
+ if (pin > (QE_PIO_PINS / 2) - 1) {
+ out_be32(&par_io->cpdir2,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cpdir2, new_mask2bits | tmp_val);
+ out_be32(&par_io->cpdir2, new_mask2bits | tmp_val);
} else {
- out_be32(&par_io[port].cpdir1,
+ out_be32(&par_io->cpdir1,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cpdir1, new_mask2bits | tmp_val);
+ out_be32(&par_io->cpdir1, new_mask2bits | tmp_val);
}
/* define pin assignment */
- tmp_val = (pin > (NUM_OF_PINS / 2) - 1) ?
- in_be32(&par_io[port].cppar2) :
- in_be32(&par_io[port].cppar1);
+ tmp_val = (pin > (QE_PIO_PINS / 2) - 1) ?
+ in_be32(&par_io->cppar2) :
+ in_be32(&par_io->cppar1);
- new_mask2bits = (u32) (assignment << (NUM_OF_PINS -
- (pin % (NUM_OF_PINS / 2) + 1) * 2));
+ new_mask2bits = (u32) (assignment << (QE_PIO_PINS -
+ (pin % (QE_PIO_PINS / 2) + 1) * 2));
/* clear and set 2 bits mask */
- if (pin > (NUM_OF_PINS / 2) - 1) {
- out_be32(&par_io[port].cppar2,
+ if (pin > (QE_PIO_PINS / 2) - 1) {
+ out_be32(&par_io->cppar2,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cppar2, new_mask2bits | tmp_val);
+ out_be32(&par_io->cppar2, new_mask2bits | tmp_val);
} else {
- out_be32(&par_io[port].cppar1,
+ out_be32(&par_io->cppar1,
~pin_mask2bits & tmp_val);
tmp_val &= ~pin_mask2bits;
- out_be32(&par_io[port].cppar1, new_mask2bits | tmp_val);
+ out_be32(&par_io->cppar1, new_mask2bits | tmp_val);
}
+}
+EXPORT_SYMBOL(__par_io_config_pin);
+
+int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
+ int assignment, int has_irq)
+{
+ if (!par_io || port >= num_par_io_ports)
+ return -EINVAL;
+ __par_io_config_pin(&par_io[port], pin, dir, open_drain, assignment,
+ has_irq);
return 0;
}
EXPORT_SYMBOL(par_io_config_pin);
if (port >= num_par_io_ports)
return -EINVAL;
- if (pin >= NUM_OF_PINS)
+ if (pin >= QE_PIO_PINS)
return -EINVAL;
/* calculate pin location */
- pin_mask = (u32) (1 << (NUM_OF_PINS - 1 - pin));
+ pin_mask = (u32) (1 << (QE_PIO_PINS - 1 - pin));
tmp_val = in_be32(&par_io[port].cpdata);
#include <asm/qe.h>
#include <asm/ucc.h>
-static DEFINE_SPINLOCK(ucc_lock);
+DEFINE_SPINLOCK(cmxgcr_lock);
+EXPORT_SYMBOL(cmxgcr_lock);
int ucc_set_qe_mux_mii_mng(unsigned int ucc_num)
{
if (ucc_num > UCC_MAX_NUM - 1)
return -EINVAL;
- spin_lock_irqsave(&ucc_lock, flags);
+ spin_lock_irqsave(&cmxgcr_lock, flags);
clrsetbits_be32(&qe_immr->qmx.cmxgcr, QE_CMXGCR_MII_ENET_MNG,
ucc_num << QE_CMXGCR_MII_ENET_MNG_SHIFT);
- spin_unlock_irqrestore(&ucc_lock, flags);
+ spin_unlock_irqrestore(&cmxgcr_lock, flags);
return 0;
}
--- /dev/null
+/*
+ * QE USB routines
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ * Shlomi Gridish <gridish@freescale.com>
+ * Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <asm/immap_qe.h>
+#include <asm/qe.h>
+
+int qe_usb_clock_set(enum qe_clock clk, int rate)
+{
+ struct qe_mux __iomem *mux = &qe_immr->qmx;
+ unsigned long flags;
+ u32 val;
+
+ switch (clk) {
+ case QE_CLK3: val = QE_CMXGCR_USBCS_CLK3; break;
+ case QE_CLK5: val = QE_CMXGCR_USBCS_CLK5; break;
+ case QE_CLK7: val = QE_CMXGCR_USBCS_CLK7; break;
+ case QE_CLK9: val = QE_CMXGCR_USBCS_CLK9; break;
+ case QE_CLK13: val = QE_CMXGCR_USBCS_CLK13; break;
+ case QE_CLK17: val = QE_CMXGCR_USBCS_CLK17; break;
+ case QE_CLK19: val = QE_CMXGCR_USBCS_CLK19; break;
+ case QE_CLK21: val = QE_CMXGCR_USBCS_CLK21; break;
+ case QE_BRG9: val = QE_CMXGCR_USBCS_BRG9; break;
+ case QE_BRG10: val = QE_CMXGCR_USBCS_BRG10; break;
+ default:
+ pr_err("%s: requested unknown clock %d\n", __func__, clk);
+ return -EINVAL;
+ }
+
+ if (qe_clock_is_brg(clk))
+ qe_setbrg(clk, rate, 1);
+
+ spin_lock_irqsave(&cmxgcr_lock, flags);
+
+ clrsetbits_be32(&mux->cmxgcr, QE_CMXGCR_USBCS, val);
+
+ spin_unlock_irqrestore(&cmxgcr_lock, flags);
+
+ return 0;
+}
+EXPORT_SYMBOL(qe_usb_clock_set);
* Copyright (C) 2004 Freescale Semiconductor, Inc.
*
* 2006 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
+ * Vitaly Bordug <vbordug@ru.mvista.com>
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
#define SERIAL_CPM_MAJOR 204
#define SERIAL_CPM_MINOR 46
-#define IS_SMC(pinfo) (pinfo->flags & FLAG_SMC)
+#define IS_SMC(pinfo) (pinfo->flags & FLAG_SMC)
#define IS_DISCARDING(pinfo) (pinfo->flags & FLAG_DISCARDING)
#define FLAG_DISCARDING 0x00000004 /* when set, don't discard */
#define FLAG_SMC 0x00000002
void (*set_lineif)(struct uart_cpm_port *);
u8 brg;
uint dp_addr;
- void *mem_addr;
+ void *mem_addr;
dma_addr_t dma_addr;
u32 mem_size;
/* helpers */
/* Keep track of 'odd' SMC2 wirings */
int is_portb;
/* wait on close if needed */
- int wait_closing;
+ int wait_closing;
/* value to combine with opcode to form cpm command */
u32 command;
};
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-extern int cpm_uart_port_map[UART_NR];
-#endif
extern int cpm_uart_nr;
extern struct uart_cpm_port cpm_uart_ports[UART_NR];
* Copyright (C) 2004, 2007 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
* (C) 2005-2006 MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
+ * Vitaly Bordug <vbordug@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <linux/bootmem.h>
#include <linux/dma-mapping.h>
#include <linux/fs_uart_pd.h>
+#include <linux/of_platform.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/fs_pd.h>
#include <asm/udbg.h>
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
-#include <linux/of_platform.h>
-#endif
-
#if defined(CONFIG_SERIAL_CPM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
/**************************************************************/
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Track which ports are configured as uarts */
-int cpm_uart_port_map[UART_NR];
-/* How many ports did we config as uarts */
-int cpm_uart_nr;
-
-/* Place-holder for board-specific stuff */
-struct platform_device* __attribute__ ((weak)) __init
-early_uart_get_pdev(int index)
-{
- return NULL;
-}
-
-
-static void cpm_uart_count(void)
-{
- cpm_uart_nr = 0;
-#ifdef CONFIG_SERIAL_CPM_SMC1
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SMC2
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC1
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC2
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC3
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
-#endif
-#ifdef CONFIG_SERIAL_CPM_SCC4
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
-#endif
-}
-
-/* Get UART number by its id */
-static int cpm_uart_id2nr(int id)
-{
- int i;
- if (id < UART_NR) {
- for (i=0; i<UART_NR; i++) {
- if (cpm_uart_port_map[i] == id)
- return i;
- }
- }
-
- /* not found or invalid argument */
- return -1;
-}
-#endif
-
/*
* Check, if transmit buffers are processed
*/
.verify_port = cpm_uart_verify_port,
};
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
struct uart_cpm_port cpm_uart_ports[UART_NR];
static int cpm_uart_init_port(struct device_node *np,
return ret;
}
-#else
-
-struct uart_cpm_port cpm_uart_ports[UART_NR] = {
- [UART_SMC1] = {
- .port = {
- .irq = SMC1_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC1].port.lock),
- },
- .flags = FLAG_SMC,
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = smc1_lineif,
- },
- [UART_SMC2] = {
- .port = {
- .irq = SMC2_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC2].port.lock),
- },
- .flags = FLAG_SMC,
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = smc2_lineif,
-#ifdef CONFIG_SERIAL_CPM_ALT_SMC2
- .is_portb = 1,
-#endif
- },
- [UART_SCC1] = {
- .port = {
- .irq = SCC1_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC1].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc1_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC2] = {
- .port = {
- .irq = SCC2_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC2].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc2_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC3] = {
- .port = {
- .irq = SCC3_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC3].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc3_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
- [UART_SCC4] = {
- .port = {
- .irq = SCC4_IRQ,
- .ops = &cpm_uart_pops,
- .iotype = UPIO_MEM,
- .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC4].port.lock),
- },
- .tx_nrfifos = TX_NUM_FIFO,
- .tx_fifosize = TX_BUF_SIZE,
- .rx_nrfifos = RX_NUM_FIFO,
- .rx_fifosize = RX_BUF_SIZE,
- .set_lineif = scc4_lineif,
- .wait_closing = SCC_WAIT_CLOSING,
- },
-};
-
-int cpm_uart_drv_get_platform_data(struct platform_device *pdev, int is_con)
-{
- struct resource *r;
- struct fs_uart_platform_info *pdata = pdev->dev.platform_data;
- int idx; /* It is UART_SMCx or UART_SCCx index */
- struct uart_cpm_port *pinfo;
- int line;
- u32 mem, pram;
-
- idx = pdata->fs_no = fs_uart_get_id(pdata);
-
- line = cpm_uart_id2nr(idx);
- if(line < 0) {
- printk(KERN_ERR"%s(): port %d is not registered", __func__, idx);
- return -EINVAL;
- }
-
- pinfo = (struct uart_cpm_port *) &cpm_uart_ports[idx];
-
- pinfo->brg = pdata->brg;
-
- if (!is_con) {
- pinfo->port.line = line;
- pinfo->port.flags = UPF_BOOT_AUTOCONF;
- }
-
- if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs")))
- return -EINVAL;
- mem = (u32)ioremap(r->start, r->end - r->start + 1);
-
- if (!(r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram")))
- return -EINVAL;
- pram = (u32)ioremap(r->start, r->end - r->start + 1);
-
- if(idx > fsid_smc2_uart) {
- pinfo->sccp = (scc_t *)mem;
- pinfo->sccup = (scc_uart_t *)pram;
- } else {
- pinfo->smcp = (smc_t *)mem;
- pinfo->smcup = (smc_uart_t *)pram;
- }
- pinfo->tx_nrfifos = pdata->tx_num_fifo;
- pinfo->tx_fifosize = pdata->tx_buf_size;
-
- pinfo->rx_nrfifos = pdata->rx_num_fifo;
- pinfo->rx_fifosize = pdata->rx_buf_size;
-
- pinfo->port.uartclk = pdata->uart_clk;
- pinfo->port.mapbase = (unsigned long)mem;
- pinfo->port.irq = platform_get_irq(pdev, 0);
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_SERIAL_CPM_CONSOLE
/*
* Print a string to the serial port trying not to disturb
static void cpm_uart_console_write(struct console *co, const char *s,
u_int count)
{
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
struct uart_cpm_port *pinfo = &cpm_uart_ports[co->index];
-#else
- struct uart_cpm_port *pinfo =
- &cpm_uart_ports[cpm_uart_port_map[co->index]];
-#endif
unsigned int i;
cbd_t __iomem *bdp, *bdbase;
unsigned char *cp;
struct uart_cpm_port *pinfo;
struct uart_port *port;
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
struct device_node *np = NULL;
int i = 0;
if (ret)
return ret;
-#else
-
- struct fs_uart_platform_info *pdata;
- struct platform_device* pdev = early_uart_get_pdev(co->index);
-
- if (!pdev) {
- pr_info("cpm_uart: console: compat mode\n");
- /* compatibility - will be cleaned up */
- cpm_uart_init_portdesc();
- }
-
- port =
- (struct uart_port *)&cpm_uart_ports[cpm_uart_port_map[co->index]];
- pinfo = (struct uart_cpm_port *)port;
- if (!pdev) {
- if (pinfo->set_lineif)
- pinfo->set_lineif(pinfo);
- } else {
- pdata = pdev->dev.platform_data;
- if (pdata)
- if (pdata->init_ioports)
- pdata->init_ioports(pdata);
-
- cpm_uart_drv_get_platform_data(pdev, 1);
- }
-
- pinfo->flags |= FLAG_CONSOLE;
-#endif
-
if (options) {
uart_parse_options(options, &baud, &parity, &bits, &flow);
} else {
.nr = UART_NR,
};
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
static int probe_index;
static int __devinit cpm_uart_probe(struct of_device *ofdev,
of_unregister_platform_driver(&cpm_uart_driver);
uart_unregister_driver(&cpm_reg);
}
-#else
-static int cpm_uart_drv_probe(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct fs_uart_platform_info *pdata;
- int ret = -ENODEV;
-
- if(!pdev) {
- printk(KERN_ERR"CPM UART: platform data missing!\n");
- return ret;
- }
-
- pdata = pdev->dev.platform_data;
-
- if ((ret = cpm_uart_drv_get_platform_data(pdev, 0)))
- return ret;
-
- pr_debug("cpm_uart_drv_probe: Adding CPM UART %d\n", cpm_uart_id2nr(pdata->fs_no));
-
- if (pdata->init_ioports)
- pdata->init_ioports(pdata);
-
- ret = uart_add_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port);
-
- return ret;
-}
-
-static int cpm_uart_drv_remove(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct fs_uart_platform_info *pdata = pdev->dev.platform_data;
-
- pr_debug("cpm_uart_drv_remove: Removing CPM UART %d\n",
- cpm_uart_id2nr(pdata->fs_no));
-
- uart_remove_one_port(&cpm_reg, &cpm_uart_ports[pdata->fs_no].port);
- return 0;
-}
-
-static struct device_driver cpm_smc_uart_driver = {
- .name = "fsl-cpm-smc:uart",
- .bus = &platform_bus_type,
- .probe = cpm_uart_drv_probe,
- .remove = cpm_uart_drv_remove,
-};
-
-static struct device_driver cpm_scc_uart_driver = {
- .name = "fsl-cpm-scc:uart",
- .bus = &platform_bus_type,
- .probe = cpm_uart_drv_probe,
- .remove = cpm_uart_drv_remove,
-};
-
-/*
- This is supposed to match uart devices on platform bus,
- */
-static int match_is_uart (struct device* dev, void* data)
-{
- struct platform_device* pdev = container_of(dev, struct platform_device, dev);
- int ret = 0;
- /* this was setfunc as uart */
- if(strstr(pdev->name,":uart")) {
- ret = 1;
- }
- return ret;
-}
-
-
-static int cpm_uart_init(void) {
-
- int ret;
- int i;
- struct device *dev;
- printk(KERN_INFO "Serial: CPM driver $Revision: 0.02 $\n");
-
- /* lookup the bus for uart devices */
- dev = bus_find_device(&platform_bus_type, NULL, 0, match_is_uart);
-
- /* There are devices on the bus - all should be OK */
- if (dev) {
- cpm_uart_count();
- cpm_reg.nr = cpm_uart_nr;
-
- if (!(ret = uart_register_driver(&cpm_reg))) {
- if ((ret = driver_register(&cpm_smc_uart_driver))) {
- uart_unregister_driver(&cpm_reg);
- return ret;
- }
- if ((ret = driver_register(&cpm_scc_uart_driver))) {
- driver_unregister(&cpm_scc_uart_driver);
- uart_unregister_driver(&cpm_reg);
- }
- }
- } else {
- /* No capable platform devices found - falling back to legacy mode */
- pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n");
- pr_info(
- "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n");
-
- /* Don't run this again, if the console driver did it already */
- if (cpm_uart_nr == 0)
- cpm_uart_init_portdesc();
-
- cpm_reg.nr = cpm_uart_nr;
- ret = uart_register_driver(&cpm_reg);
-
- if (ret)
- return ret;
-
- for (i = 0; i < cpm_uart_nr; i++) {
- int con = cpm_uart_port_map[i];
- cpm_uart_ports[con].port.line = i;
- cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF;
- if (cpm_uart_ports[con].set_lineif)
- cpm_uart_ports[con].set_lineif(&cpm_uart_ports[con]);
- uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port);
- }
-
- }
- return ret;
-}
-
-static void __exit cpm_uart_exit(void)
-{
- driver_unregister(&cpm_scc_uart_driver);
- driver_unregister(&cpm_smc_uart_driver);
- uart_unregister_driver(&cpm_reg);
-}
-#endif
module_init(cpm_uart_init);
module_exit(cpm_uart_exit);
* Copyright (C) 2004 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
* (C) 2006 MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
+ * Vitaly Bordug <vbordug@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
/**************************************************************/
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
{
cpm_command(port->command, cmd);
iounmap(pram);
}
-#else
-void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
-{
- ushort val;
- int line = port - cpm_uart_ports;
- volatile cpm8xx_t *cp = cpmp;
-
- switch (line) {
- case UART_SMC1:
- val = mk_cr_cmd(CPM_CR_CH_SMC1, cmd) | CPM_CR_FLG;
- break;
- case UART_SMC2:
- val = mk_cr_cmd(CPM_CR_CH_SMC2, cmd) | CPM_CR_FLG;
- break;
- case UART_SCC1:
- val = mk_cr_cmd(CPM_CR_CH_SCC1, cmd) | CPM_CR_FLG;
- break;
- case UART_SCC2:
- val = mk_cr_cmd(CPM_CR_CH_SCC2, cmd) | CPM_CR_FLG;
- break;
- case UART_SCC3:
- val = mk_cr_cmd(CPM_CR_CH_SCC3, cmd) | CPM_CR_FLG;
- break;
- case UART_SCC4:
- val = mk_cr_cmd(CPM_CR_CH_SCC4, cmd) | CPM_CR_FLG;
- break;
- default:
- return;
-
- }
- cp->cp_cpcr = val;
- while (cp->cp_cpcr & CPM_CR_FLG) ;
-}
-
-void smc1_lineif(struct uart_cpm_port *pinfo)
-{
- pinfo->brg = 1;
-}
-
-void smc2_lineif(struct uart_cpm_port *pinfo)
-{
- pinfo->brg = 2;
-}
-
-void scc1_lineif(struct uart_cpm_port *pinfo)
-{
- /* XXX SCC1: insert port configuration here */
- pinfo->brg = 1;
-}
-
-void scc2_lineif(struct uart_cpm_port *pinfo)
-{
- /* XXX SCC2: insert port configuration here */
- pinfo->brg = 2;
-}
-
-void scc3_lineif(struct uart_cpm_port *pinfo)
-{
- /* XXX SCC3: insert port configuration here */
- pinfo->brg = 3;
-}
-
-void scc4_lineif(struct uart_cpm_port *pinfo)
-{
- /* XXX SCC4: insert port configuration here */
- pinfo->brg = 4;
-}
-#endif
-
/*
* Allocate DP-Ram and memory buffers. We need to allocate a transmit and
* receive buffer descriptors from dual port ram, and a character
cpm_dpfree(pinfo->dp_addr);
}
-
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Setup any dynamic params in the uart desc */
-int cpm_uart_init_portdesc(void)
-{
- pr_debug("CPM uart[-]:init portdesc\n");
-
- cpm_uart_nr = 0;
-#ifdef CONFIG_SERIAL_CPM_SMC1
- cpm_uart_ports[UART_SMC1].smcp = &cpmp->cp_smc[0];
-/*
- * Is SMC1 being relocated?
- */
-# ifdef CONFIG_I2C_SPI_SMC1_UCODE_PATCH
- cpm_uart_ports[UART_SMC1].smcup =
- (smc_uart_t *) & cpmp->cp_dparam[0x3C0];
-# else
- cpm_uart_ports[UART_SMC1].smcup =
- (smc_uart_t *) & cpmp->cp_dparam[PROFF_SMC1];
-# endif
- cpm_uart_ports[UART_SMC1].port.mapbase =
- (unsigned long)&cpmp->cp_smc[0];
- cpm_uart_ports[UART_SMC1].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
- cpm_uart_ports[UART_SMC1].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC1].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SMC2
- cpm_uart_ports[UART_SMC2].smcp = &cpmp->cp_smc[1];
- cpm_uart_ports[UART_SMC2].smcup =
- (smc_uart_t *) & cpmp->cp_dparam[PROFF_SMC2];
- cpm_uart_ports[UART_SMC2].port.mapbase =
- (unsigned long)&cpmp->cp_smc[1];
- cpm_uart_ports[UART_SMC2].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
- cpm_uart_ports[UART_SMC2].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC2].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC1
- cpm_uart_ports[UART_SCC1].sccp = &cpmp->cp_scc[0];
- cpm_uart_ports[UART_SCC1].sccup =
- (scc_uart_t *) & cpmp->cp_dparam[PROFF_SCC1];
- cpm_uart_ports[UART_SCC1].port.mapbase =
- (unsigned long)&cpmp->cp_scc[0];
- cpm_uart_ports[UART_SCC1].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC1].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC1].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC2
- cpm_uart_ports[UART_SCC2].sccp = &cpmp->cp_scc[1];
- cpm_uart_ports[UART_SCC2].sccup =
- (scc_uart_t *) & cpmp->cp_dparam[PROFF_SCC2];
- cpm_uart_ports[UART_SCC2].port.mapbase =
- (unsigned long)&cpmp->cp_scc[1];
- cpm_uart_ports[UART_SCC2].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC2].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC2].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC3
- cpm_uart_ports[UART_SCC3].sccp = &cpmp->cp_scc[2];
- cpm_uart_ports[UART_SCC3].sccup =
- (scc_uart_t *) & cpmp->cp_dparam[PROFF_SCC3];
- cpm_uart_ports[UART_SCC3].port.mapbase =
- (unsigned long)&cpmp->cp_scc[2];
- cpm_uart_ports[UART_SCC3].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC3].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC3].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC4
- cpm_uart_ports[UART_SCC4].sccp = &cpmp->cp_scc[3];
- cpm_uart_ports[UART_SCC4].sccup =
- (scc_uart_t *) & cpmp->cp_dparam[PROFF_SCC4];
- cpm_uart_ports[UART_SCC4].port.mapbase =
- (unsigned long)&cpmp->cp_scc[3];
- cpm_uart_ports[UART_SCC4].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC4].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC4].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
-#endif
- return 0;
-}
-#endif
* linux/drivers/serial/cpm_uart/cpm_uart_cpm1.h
*
* Driver for CPM (SCC/SMC) serial ports
- *
+ *
* definitions for cpm1
*
*/
#include <asm/cpm1.h>
-/* defines for IRQs */
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-#define SMC1_IRQ (CPM_IRQ_OFFSET + CPMVEC_SMC1)
-#define SMC2_IRQ (CPM_IRQ_OFFSET + CPMVEC_SMC2)
-#define SCC1_IRQ (CPM_IRQ_OFFSET + CPMVEC_SCC1)
-#define SCC2_IRQ (CPM_IRQ_OFFSET + CPMVEC_SCC2)
-#define SCC3_IRQ (CPM_IRQ_OFFSET + CPMVEC_SCC3)
-#define SCC4_IRQ (CPM_IRQ_OFFSET + CPMVEC_SCC4)
-#endif
-
static inline void cpm_set_brg(int brg, int baud)
{
cpm_setbrg(brg, baud);
*
* Maintainer: Kumar Gala (galak@kernel.crashing.org) (CPM2)
* Pantelis Antoniou (panto@intracom.gr) (CPM1)
- *
+ *
* Copyright (C) 2004 Freescale Semiconductor, Inc.
* (C) 2004 Intracom, S.A.
* (C) 2006 MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
+ * Vitaly Bordug <vbordug@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/fs_pd.h>
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#include <asm/prom.h>
-#endif
#include <linux/serial_core.h>
#include <linux/kernel.h>
/**************************************************************/
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
{
cpm_command(port->command, cmd);
iounmap(pram);
}
-#else
-void cpm_line_cr_cmd(struct uart_cpm_port *port, int cmd)
-{
- ulong val;
- int line = port - cpm_uart_ports;
- volatile cpm_cpm2_t *cp = cpm2_map(im_cpm);
-
-
- switch (line) {
- case UART_SMC1:
- val = mk_cr_cmd(CPM_CR_SMC1_PAGE, CPM_CR_SMC1_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- case UART_SMC2:
- val = mk_cr_cmd(CPM_CR_SMC2_PAGE, CPM_CR_SMC2_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- case UART_SCC1:
- val = mk_cr_cmd(CPM_CR_SCC1_PAGE, CPM_CR_SCC1_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- case UART_SCC2:
- val = mk_cr_cmd(CPM_CR_SCC2_PAGE, CPM_CR_SCC2_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- case UART_SCC3:
- val = mk_cr_cmd(CPM_CR_SCC3_PAGE, CPM_CR_SCC3_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- case UART_SCC4:
- val = mk_cr_cmd(CPM_CR_SCC4_PAGE, CPM_CR_SCC4_SBLOCK, 0,
- cmd) | CPM_CR_FLG;
- break;
- default:
- return;
-
- }
- cp->cp_cpcr = val;
- while (cp->cp_cpcr & CPM_CR_FLG) ;
-
- cpm2_unmap(cp);
-}
-
-void smc1_lineif(struct uart_cpm_port *pinfo)
-{
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-
- /* SMC1 is only on port D */
- io->iop_ppard |= 0x00c00000;
- io->iop_pdird |= 0x00400000;
- io->iop_pdird &= ~0x00800000;
- io->iop_psord &= ~0x00c00000;
-
- /* Wire BRG1 to SMC1 */
- cpmux->cmx_smr &= 0x0f;
- pinfo->brg = 1;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-
-void smc2_lineif(struct uart_cpm_port *pinfo)
-{
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-
- /* SMC2 is only on port A */
- io->iop_ppara |= 0x00c00000;
- io->iop_pdira |= 0x00400000;
- io->iop_pdira &= ~0x00800000;
- io->iop_psora &= ~0x00c00000;
-
- /* Wire BRG2 to SMC2 */
- cpmux->cmx_smr &= 0xf0;
- pinfo->brg = 2;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-
-void scc1_lineif(struct uart_cpm_port *pinfo)
-{
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-
- /* Use Port D for SCC1 instead of other functions. */
- io->iop_ppard |= 0x00000003;
- io->iop_psord &= ~0x00000001; /* Rx */
- io->iop_psord |= 0x00000002; /* Tx */
- io->iop_pdird &= ~0x00000001; /* Rx */
- io->iop_pdird |= 0x00000002; /* Tx */
-
- /* Wire BRG1 to SCC1 */
- cpmux->cmx_scr &= 0x00ffffff;
- cpmux->cmx_scr |= 0x00000000;
- pinfo->brg = 1;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-
-void scc2_lineif(struct uart_cpm_port *pinfo)
-{
- /*
- * STx GP3 uses the SCC2 secondary option pin assignment
- * which this driver doesn't account for in the static
- * pin assignments. This kind of board specific info
- * really has to get out of the driver so boards can
- * be supported in a sane fashion.
- */
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-#ifndef CONFIG_STX_GP3
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
-
- io->iop_pparb |= 0x008b0000;
- io->iop_pdirb |= 0x00880000;
- io->iop_psorb |= 0x00880000;
- io->iop_pdirb &= ~0x00030000;
- io->iop_psorb &= ~0x00030000;
-#endif
- cpmux->cmx_scr &= 0xff00ffff;
- cpmux->cmx_scr |= 0x00090000;
- pinfo->brg = 2;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-
-void scc3_lineif(struct uart_cpm_port *pinfo)
-{
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-
- io->iop_pparb |= 0x008b0000;
- io->iop_pdirb |= 0x00880000;
- io->iop_psorb |= 0x00880000;
- io->iop_pdirb &= ~0x00030000;
- io->iop_psorb &= ~0x00030000;
- cpmux->cmx_scr &= 0xffff00ff;
- cpmux->cmx_scr |= 0x00001200;
- pinfo->brg = 3;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-
-void scc4_lineif(struct uart_cpm_port *pinfo)
-{
- volatile iop_cpm2_t *io = cpm2_map(im_ioport);
- volatile cpmux_t *cpmux = cpm2_map(im_cpmux);
-
- io->iop_ppard |= 0x00000600;
- io->iop_psord &= ~0x00000600; /* Tx/Rx */
- io->iop_pdird &= ~0x00000200; /* Rx */
- io->iop_pdird |= 0x00000400; /* Tx */
-
- cpmux->cmx_scr &= 0xffffff00;
- cpmux->cmx_scr |= 0x0000001b;
- pinfo->brg = 4;
-
- cpm2_unmap(cpmux);
- cpm2_unmap(io);
-}
-#endif
-
/*
- * Allocate DP-Ram and memory buffers. We need to allocate a transmit and
+ * Allocate DP-Ram and memory buffers. We need to allocate a transmit and
* receive buffer descriptors from dual port ram, and a character
* buffer area from host mem. If we are allocating for the console we need
* to do it from bootmem
cpm_dpfree(pinfo->dp_addr);
}
-
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Setup any dynamic params in the uart desc */
-int cpm_uart_init_portdesc(void)
-{
-#if defined(CONFIG_SERIAL_CPM_SMC1) || defined(CONFIG_SERIAL_CPM_SMC2)
- u16 *addr;
-#endif
- pr_debug("CPM uart[-]:init portdesc\n");
-
- cpm_uart_nr = 0;
-#ifdef CONFIG_SERIAL_CPM_SMC1
- cpm_uart_ports[UART_SMC1].smcp = (smc_t *) cpm2_map(im_smc[0]);
- cpm_uart_ports[UART_SMC1].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SMC1].smcp;
-
- cpm_uart_ports[UART_SMC1].smcup =
- (smc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SMC1], PROFF_SMC_SIZE);
- addr = (u16 *)cpm2_map_size(im_dprambase[PROFF_SMC1_BASE], 2);
- *addr = PROFF_SMC1;
- cpm2_unmap(addr);
-
- cpm_uart_ports[UART_SMC1].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
- cpm_uart_ports[UART_SMC1].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC1].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC1;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SMC2
- cpm_uart_ports[UART_SMC2].smcp = (smc_t *) cpm2_map(im_smc[1]);
- cpm_uart_ports[UART_SMC2].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SMC2].smcp;
-
- cpm_uart_ports[UART_SMC2].smcup =
- (smc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SMC2], PROFF_SMC_SIZE);
- addr = (u16 *)cpm2_map_size(im_dprambase[PROFF_SMC2_BASE], 2);
- *addr = PROFF_SMC2;
- cpm2_unmap(addr);
-
- cpm_uart_ports[UART_SMC2].smcp->smc_smcm |= (SMCM_RX | SMCM_TX);
- cpm_uart_ports[UART_SMC2].smcp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- cpm_uart_ports[UART_SMC2].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SMC2;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC1
- cpm_uart_ports[UART_SCC1].sccp = (scc_t *) cpm2_map(im_scc[0]);
- cpm_uart_ports[UART_SCC1].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SCC1].sccp;
- cpm_uart_ports[UART_SCC1].sccup =
- (scc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SCC1], PROFF_SCC_SIZE);
-
- cpm_uart_ports[UART_SCC1].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC1].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC1].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC1;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC2
- cpm_uart_ports[UART_SCC2].sccp = (scc_t *) cpm2_map(im_scc[1]);
- cpm_uart_ports[UART_SCC2].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SCC2].sccp;
- cpm_uart_ports[UART_SCC2].sccup =
- (scc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SCC2], PROFF_SCC_SIZE);
-
- cpm_uart_ports[UART_SCC2].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC2].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC2].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC2;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC3
- cpm_uart_ports[UART_SCC3].sccp = (scc_t *) cpm2_map(im_scc[2]);
- cpm_uart_ports[UART_SCC3].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SCC3].sccp;
- cpm_uart_ports[UART_SCC3].sccup =
- (scc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SCC3], PROFF_SCC_SIZE);
-
- cpm_uart_ports[UART_SCC3].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC3].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC3].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC3;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC4
- cpm_uart_ports[UART_SCC4].sccp = (scc_t *) cpm2_map(im_scc[3]);
- cpm_uart_ports[UART_SCC4].port.mapbase =
- (unsigned long)cpm_uart_ports[UART_SCC4].sccp;
- cpm_uart_ports[UART_SCC4].sccup =
- (scc_uart_t *) cpm2_map_size(im_dprambase[PROFF_SCC4], PROFF_SCC_SIZE);
-
- cpm_uart_ports[UART_SCC4].sccp->scc_sccm &=
- ~(UART_SCCM_TX | UART_SCCM_RX);
- cpm_uart_ports[UART_SCC4].sccp->scc_gsmrl &=
- ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
- cpm_uart_ports[UART_SCC4].port.uartclk = uart_clock();
- cpm_uart_port_map[cpm_uart_nr++] = UART_SCC4;
-#endif
-
- return 0;
-}
-#endif
* linux/drivers/serial/cpm_uart/cpm_uart_cpm2.h
*
* Driver for CPM (SCC/SMC) serial ports
- *
+ *
* definitions for cpm2
*
*/
#include <asm/cpm2.h>
-/* defines for IRQs */
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-#define SMC1_IRQ SIU_INT_SMC1
-#define SMC2_IRQ SIU_INT_SMC2
-#define SCC1_IRQ SIU_INT_SCC1
-#define SCC2_IRQ SIU_INT_SCC2
-#define SCC3_IRQ SIU_INT_SCC3
-#define SCC4_IRQ SIU_INT_SCC4
-#endif
-
static inline void cpm_set_brg(int brg, int baud)
{
cpm_setbrg(brg, baud);
#if defined(CONFIG_8xx) || defined(CONFIG_403GCX)
#define L1_CACHE_SHIFT 4
#define MAX_COPY_PREFETCH 1
+#elif defined(CONFIG_PPC_E500MC)
+#define L1_CACHE_SHIFT 6
+#define MAX_COPY_PREFETCH 4
#elif defined(CONFIG_PPC32)
#define L1_CACHE_SHIFT 5
#define MAX_COPY_PREFETCH 4
int cpm_muram_free(unsigned long offset);
unsigned long cpm_muram_alloc_fixed(unsigned long offset, unsigned long size);
void __iomem *cpm_muram_addr(unsigned long offset);
+unsigned long cpm_muram_offset(void __iomem *addr);
dma_addr_t cpm_muram_dma(void __iomem *addr);
int cpm_command(u32 command, u8 opcode);
#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#endif
-
/* Export the base address of the communication processor registers
* and dual port ram.
*/
extern cpm8xx_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
#define cpm_dpram_phys cpm_muram_dma
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-extern uint cpm_dpram_phys(u8 *addr);
-#endif
extern void cpm_setbrg(uint brg, uint rate);
#define mk_cr_cmd(PG, SBC, MCN, OP) \
((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/* Dual Port RAM addresses. The first 16K is available for almost
- * any CPM use, so we put the BDs there. The first 128 bytes are
- * used for SMC1 and SMC2 parameter RAM, so we start allocating
- * BDs above that. All of this must change when we start
- * downloading RAM microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)128)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
-#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x00009000)
-#else
-#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE)
-#define CPM_FCC_SPECIAL_BASE ((uint)0x0000b000)
-#endif
-#endif
-
/* The number of pages of host memory we allocate for CPM. This is
* done early in kernel initialization to get physically contiguous
* pages.
*/
extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
#define cpm_dpalloc cpm_muram_alloc
#define cpm_dpfree cpm_muram_free
#define cpm_dpram_addr cpm_muram_addr
-#else
-extern unsigned long cpm_dpalloc(uint size, uint align);
-extern int cpm_dpfree(unsigned long offset);
-extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
-extern void cpm_dpdump(void);
-extern void *cpm_dpram_addr(unsigned long offset);
-#endif
extern void cpm_setbrg(uint brg, uint rate);
extern void cpm2_fastbrg(uint brg, uint rate, int div16);
#define CPU_FTR_TAU ASM_CONST(0x0000000000000010)
#define CPU_FTR_CAN_DOZE ASM_CONST(0x0000000000000020)
#define CPU_FTR_USE_TB ASM_CONST(0x0000000000000040)
-#define CPU_FTR_604_PERF_MON ASM_CONST(0x0000000000000080)
+#define CPU_FTR_L2CSR ASM_CONST(0x0000000000000080)
#define CPU_FTR_601 ASM_CONST(0x0000000000000100)
#define CPU_FTR_HPTE_TABLE ASM_CONST(0x0000000000000200)
#define CPU_FTR_CAN_NAP ASM_CONST(0x0000000000000400)
CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB | \
CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_PPC_LE)
#define CPU_FTRS_604 (CPU_FTR_COMMON | \
- CPU_FTR_USE_TB | CPU_FTR_604_PERF_MON | CPU_FTR_HPTE_TABLE | \
- CPU_FTR_PPC_LE)
+ CPU_FTR_USE_TB | CPU_FTR_HPTE_TABLE | CPU_FTR_PPC_LE)
#define CPU_FTRS_740_NOTAU (CPU_FTR_COMMON | \
CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB | CPU_FTR_L2CR | \
CPU_FTR_HPTE_TABLE | CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_PPC_LE)
#define CPU_FTRS_E200 (CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
CPU_FTR_NODSISRALIGN | CPU_FTR_COHERENT_ICACHE | \
CPU_FTR_UNIFIED_ID_CACHE)
-#define CPU_FTRS_E500 (CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
+#define CPU_FTRS_E500 (CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB | \
+ CPU_FTR_SPE_COMP | CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_NODSISRALIGN)
+#define CPU_FTRS_E500_2 (CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB | \
+ CPU_FTR_SPE_COMP | CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_BIG_PHYS | \
CPU_FTR_NODSISRALIGN)
-#define CPU_FTRS_E500_2 (CPU_FTR_USE_TB | CPU_FTR_SPE_COMP | \
- CPU_FTR_BIG_PHYS | CPU_FTR_NODSISRALIGN)
+#define CPU_FTRS_E500MC (CPU_FTR_MAYBE_CAN_DOZE | CPU_FTR_USE_TB | \
+ CPU_FTR_MAYBE_CAN_NAP | CPU_FTR_BIG_PHYS | CPU_FTR_NODSISRALIGN | \
+ CPU_FTR_L2CSR)
#define CPU_FTRS_GENERIC_32 (CPU_FTR_COMMON | CPU_FTR_NODSISRALIGN)
/* 64-bit CPUs */
CPU_FTRS_E200 |
#endif
#ifdef CONFIG_E500
- CPU_FTRS_E500 | CPU_FTRS_E500_2 |
+ CPU_FTRS_E500 | CPU_FTRS_E500_2 | CPU_FTRS_E500MC |
#endif
0,
};
CPU_FTRS_E200 &
#endif
#ifdef CONFIG_E500
- CPU_FTRS_E500 & CPU_FTRS_E500_2 &
+ CPU_FTRS_E500 & CPU_FTRS_E500_2 & CPU_FTRS_E500MC &
#endif
CPU_FTRS_POSSIBLE,
};
--- /dev/null
+/*
+ * Freescale General-purpose Timers Module
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ * Shlomi Gridish <gridish@freescale.com>
+ * Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_FSL_GTM_H
+#define __ASM_FSL_GTM_H
+
+#include <linux/types.h>
+
+struct gtm;
+
+struct gtm_timer {
+ unsigned int irq;
+
+ struct gtm *gtm;
+ bool requested;
+ u8 __iomem *gtcfr;
+ __be16 __iomem *gtmdr;
+ __be16 __iomem *gtpsr;
+ __be16 __iomem *gtcnr;
+ __be16 __iomem *gtrfr;
+ __be16 __iomem *gtevr;
+};
+
+extern struct gtm_timer *gtm_get_timer16(void);
+extern struct gtm_timer *gtm_get_specific_timer16(struct gtm *gtm,
+ unsigned int timer);
+extern void gtm_put_timer16(struct gtm_timer *tmr);
+extern int gtm_set_timer16(struct gtm_timer *tmr, unsigned long usec,
+ bool reload);
+extern int gtm_set_exact_timer16(struct gtm_timer *tmr, u16 usec,
+ bool reload);
+extern void gtm_stop_timer16(struct gtm_timer *tmr);
+extern void gtm_ack_timer16(struct gtm_timer *tmr, u16 events);
+
+#endif /* __ASM_FSL_GTM_H */
#endif
};
+extern void e500_idle(void);
extern void power4_idle(void);
extern void power4_cpu_offline_powersave(void);
extern void ppc6xx_idle(void);
#define _ASM_POWERPC_QE_H
#ifdef __KERNEL__
+#include <linux/spinlock.h>
+#include <asm/cpm.h>
#include <asm/immap_qe.h>
#define QE_NUM_OF_SNUM 28
QE_CLK_DUMMY
};
+static inline bool qe_clock_is_brg(enum qe_clock clk)
+{
+ return clk >= QE_BRG1 && clk <= QE_BRG16;
+}
+
+extern spinlock_t cmxgcr_lock;
+
/* Export QE common operations */
-extern void qe_reset(void);
+extern void __init qe_reset(void);
+
+/* QE PIO */
+#define QE_PIO_PINS 32
+
+struct qe_pio_regs {
+ __be32 cpodr; /* Open drain register */
+ __be32 cpdata; /* Data register */
+ __be32 cpdir1; /* Direction register */
+ __be32 cpdir2; /* Direction register */
+ __be32 cppar1; /* Pin assignment register */
+ __be32 cppar2; /* Pin assignment register */
+#ifdef CONFIG_PPC_85xx
+ u8 pad[8];
+#endif
+};
+
extern int par_io_init(struct device_node *np);
extern int par_io_of_config(struct device_node *np);
+#define QE_PIO_DIR_IN 2
+#define QE_PIO_DIR_OUT 1
+extern void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin,
+ int dir, int open_drain, int assignment,
+ int has_irq);
extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
int assignment, int has_irq);
extern int par_io_data_set(u8 port, u8 pin, u8 val);
int qe_setbrg(enum qe_clock brg, unsigned int rate, unsigned int multiplier);
int qe_get_snum(void);
void qe_put_snum(u8 snum);
-unsigned long qe_muram_alloc(int size, int align);
-int qe_muram_free(unsigned long offset);
-unsigned long qe_muram_alloc_fixed(unsigned long offset, int size);
-void qe_muram_dump(void);
-
-static inline void __iomem *qe_muram_addr(unsigned long offset)
-{
- return (void __iomem *)&qe_immr->muram[offset];
-}
-
-static inline unsigned long qe_muram_offset(void __iomem *addr)
-{
- return addr - (void __iomem *)qe_immr->muram;
-}
+/* we actually use cpm_muram implementation, define this for convenience */
+#define qe_muram_init cpm_muram_init
+#define qe_muram_alloc cpm_muram_alloc
+#define qe_muram_alloc_fixed cpm_muram_alloc_fixed
+#define qe_muram_free cpm_muram_free
+#define qe_muram_addr cpm_muram_addr
+#define qe_muram_offset cpm_muram_offset
/* Structure that defines QE firmware binary files.
*
/* Obtain information on the uploaded firmware */
struct qe_firmware_info *qe_get_firmware_info(void);
+/* QE USB */
+int qe_usb_clock_set(enum qe_clock clk, int rate);
+
/* Buffer descriptors */
struct qe_bd {
__be16 status;
#define BD_STATUS_MASK 0xffff0000
#define BD_LENGTH_MASK 0x0000ffff
-#define BD_SC_EMPTY 0x8000 /* Receive is empty */
-#define BD_SC_READY 0x8000 /* Transmit is ready */
-#define BD_SC_WRAP 0x2000 /* Last buffer descriptor */
-#define BD_SC_INTRPT 0x1000 /* Interrupt on change */
-#define BD_SC_LAST 0x0800 /* Last buffer in frame */
-#define BD_SC_CM 0x0200 /* Continous mode */
-#define BD_SC_ID 0x0100 /* Rec'd too many idles */
-#define BD_SC_P 0x0100 /* xmt preamble */
-#define BD_SC_BR 0x0020 /* Break received */
-#define BD_SC_FR 0x0010 /* Framing error */
-#define BD_SC_PR 0x0008 /* Parity error */
-#define BD_SC_OV 0x0002 /* Overrun */
-#define BD_SC_CD 0x0001 /* ?? */
-
/* Alignment */
#define QE_INTR_TABLE_ALIGN 16 /* ??? */
#define QE_ALIGNMENT_OF_BD 8
#define QE_CMXGCR_MII_ENET_MNG 0x00007000
#define QE_CMXGCR_MII_ENET_MNG_SHIFT 12
#define QE_CMXGCR_USBCS 0x0000000f
+#define QE_CMXGCR_USBCS_CLK3 0x1
+#define QE_CMXGCR_USBCS_CLK5 0x2
+#define QE_CMXGCR_USBCS_CLK7 0x3
+#define QE_CMXGCR_USBCS_CLK9 0x4
+#define QE_CMXGCR_USBCS_CLK13 0x5
+#define QE_CMXGCR_USBCS_CLK17 0x6
+#define QE_CMXGCR_USBCS_CLK19 0x7
+#define QE_CMXGCR_USBCS_CLK21 0x8
+#define QE_CMXGCR_USBCS_BRG9 0x9
+#define QE_CMXGCR_USBCS_BRG10 0xa
/* QE CECR Commands.
*/
#define QE_HPAC_START_TX 0x0000060b
#define QE_HPAC_START_RX 0x0000070b
#define QE_USB_STOP_TX 0x0000000a
-#define QE_USB_RESTART_TX 0x0000000b
+#define QE_USB_RESTART_TX 0x0000000c
#define QE_QMC_STOP_TX 0x0000000c
#define QE_QMC_STOP_RX 0x0000000d
#define QE_SS7_SU_FIL_RESET 0x0000000e
#define HID0_DAPUEN (1<<8) /* Debug APU enable */
#define HID0_SGE (1<<7) /* Store Gathering Enable */
#define HID0_SIED (1<<7) /* Serial Instr. Execution [Disable] */
-#define HID0_DFCA (1<<6) /* Data Cache Flush Assist */
+#define HID0_DCFA (1<<6) /* Data Cache Flush Assist */
#define HID0_LRSTK (1<<4) /* Link register stack - 745x */
#define HID0_BTIC (1<<5) /* Branch Target Instr Cache Enable */
#define HID0_ABE (1<<3) /* Address Broadcast Enable */
#define SPRN_SPEFSCR 0x200 /* SPE & Embedded FP Status & Control */
#define SPRN_BBEAR 0x201 /* Branch Buffer Entry Address Register */
#define SPRN_BBTAR 0x202 /* Branch Buffer Target Address Register */
+#define SPRN_L1CFG0 0x203 /* L1 Cache Configure Register 0 */
+#define SPRN_L1CFG1 0x204 /* L1 Cache Configure Register 1 */
#define SPRN_ATB 0x20E /* Alternate Time Base */
#define SPRN_ATBL 0x20E /* Alternate Time Base Lower */
#define SPRN_ATBU 0x20F /* Alternate Time Base Upper */
#define SPRN_DSRR1 0x23F /* Debug Save and Restore Register 1 */
#define SPRN_SPRG8 0x25C /* Special Purpose Register General 8 */
#define SPRN_SPRG9 0x25D /* Special Purpose Register General 9 */
+#define SPRN_L1CSR2 0x25E /* L1 Cache Control and Status Register 2 */
#define SPRN_MAS0 0x270 /* MMU Assist Register 0 */
#define SPRN_MAS1 0x271 /* MMU Assist Register 1 */
#define SPRN_MAS2 0x272 /* MMU Assist Register 2 */
#define SPRN_L1CSR1 0x3F3 /* L1 Cache Control and Status Register 1 */
#define SPRN_PIT 0x3DB /* Programmable Interval Timer */
#define SPRN_BUCSR 0x3F5 /* Branch Unit Control and Status */
+#define SPRN_L2CSR0 0x3F9 /* L2 Data Cache Control and Status Register 0 */
+#define SPRN_L2CSR1 0x3FA /* L2 Data Cache Control and Status Register 1 */
#define SPRN_DCCR 0x3FA /* Data Cache Cacheability Register */
#define SPRN_ICCR 0x3FB /* Instruction Cache Cacheability Register */
#define SPRN_SVR 0x3FF /* System Version Register */
#ifdef CONFIG_BOOKE
#define DBSR_IC 0x08000000 /* Instruction Completion */
#define DBSR_BT 0x04000000 /* Branch Taken */
+#define DBSR_IRPT 0x02000000 /* Exception Debug Event */
#define DBSR_TIE 0x01000000 /* Trap Instruction Event */
#define DBSR_IAC1 0x00800000 /* Instr Address Compare 1 Event */
#define DBSR_IAC2 0x00400000 /* Instr Address Compare 2 Event */
#define DBSR_DAC1W 0x00040000 /* Data Addr Compare 1 Write Event */
#define DBSR_DAC2R 0x00020000 /* Data Addr Compare 2 Read Event */
#define DBSR_DAC2W 0x00010000 /* Data Addr Compare 2 Write Event */
+#define DBSR_RET 0x00008000 /* Return Debug Event */
+#define DBSR_CIRPT 0x00000040 /* Critical Interrupt Taken Event */
+#define DBSR_CRET 0x00000020 /* Critical Return Debug Event */
#endif
#ifdef CONFIG_40x
#define DBSR_IC 0x80000000 /* Instruction Completion */
#define DBSR_BT 0x40000000 /* Branch taken */
+#define DBSR_IRPT 0x20000000 /* Exception Debug Event */
#define DBSR_TIE 0x10000000 /* Trap Instruction debug Event */
#define DBSR_IAC1 0x04000000 /* Instruction Address Compare 1 Event */
#define DBSR_IAC2 0x02000000 /* Instruction Address Compare 2 Event */
#define ESR_BO 0x00020000 /* Byte Ordering */
/* Bit definitions related to the DBCR0. */
+#if defined(CONFIG_40x)
#define DBCR0_EDM 0x80000000 /* External Debug Mode */
#define DBCR0_IDM 0x40000000 /* Internal Debug Mode */
#define DBCR0_RST 0x30000000 /* all the bits in the RST field */
#define DBCR0_RST_CORE 0x10000000 /* Core Reset */
#define DBCR0_RST_NONE 0x00000000 /* No Reset */
#define DBCR0_IC 0x08000000 /* Instruction Completion */
+#define DBCR0_ICMP DBCR0_IC
#define DBCR0_BT 0x04000000 /* Branch Taken */
+#define DBCR0_BRT DBCR0_BT
#define DBCR0_EDE 0x02000000 /* Exception Debug Event */
+#define DBCR0_IRPT DBCR0_EDE
#define DBCR0_TDE 0x01000000 /* TRAP Debug Event */
#define DBCR0_IA1 0x00800000 /* Instr Addr compare 1 enable */
+#define DBCR0_IAC1 DBCR0_IA1
#define DBCR0_IA2 0x00400000 /* Instr Addr compare 2 enable */
+#define DBCR0_IAC2 DBCR0_IA2
#define DBCR0_IA12 0x00200000 /* Instr Addr 1-2 range enable */
#define DBCR0_IA12X 0x00100000 /* Instr Addr 1-2 range eXclusive */
#define DBCR0_IA3 0x00080000 /* Instr Addr compare 3 enable */
+#define DBCR0_IAC3 DBCR0_IA3
#define DBCR0_IA4 0x00040000 /* Instr Addr compare 4 enable */
+#define DBCR0_IAC4 DBCR0_IA4
#define DBCR0_IA34 0x00020000 /* Instr Addr 3-4 range Enable */
#define DBCR0_IA34X 0x00010000 /* Instr Addr 3-4 range eXclusive */
#define DBCR0_IA12T 0x00008000 /* Instr Addr 1-2 range Toggle */
#define DBCR0_IA34T 0x00004000 /* Instr Addr 3-4 range Toggle */
#define DBCR0_FT 0x00000001 /* Freeze Timers on debug event */
+#elif defined(CONFIG_BOOKE)
+#define DBCR0_EDM 0x80000000 /* External Debug Mode */
+#define DBCR0_IDM 0x40000000 /* Internal Debug Mode */
+#define DBCR0_RST 0x30000000 /* all the bits in the RST field */
+/* DBCR0_RST_* is 44x specific and not followed in fsl booke */
+#define DBCR0_RST_SYSTEM 0x30000000 /* System Reset */
+#define DBCR0_RST_CHIP 0x20000000 /* Chip Reset */
+#define DBCR0_RST_CORE 0x10000000 /* Core Reset */
+#define DBCR0_RST_NONE 0x00000000 /* No Reset */
+#define DBCR0_ICMP 0x08000000 /* Instruction Completion */
+#define DBCR0_IC DBCR0_ICMP
+#define DBCR0_BRT 0x04000000 /* Branch Taken */
+#define DBCR0_BT DBCR0_BRT
+#define DBCR0_IRPT 0x02000000 /* Exception Debug Event */
+#define DBCR0_TDE 0x01000000 /* TRAP Debug Event */
+#define DBCR0_TIE DBCR0_TDE
+#define DBCR0_IAC1 0x00800000 /* Instr Addr compare 1 enable */
+#define DBCR0_IAC2 0x00400000 /* Instr Addr compare 2 enable */
+#define DBCR0_IAC3 0x00200000 /* Instr Addr compare 3 enable */
+#define DBCR0_IAC4 0x00100000 /* Instr Addr compare 4 enable */
+#define DBCR0_DAC1R 0x00080000 /* DAC 1 Read enable */
+#define DBCR0_DAC1W 0x00040000 /* DAC 1 Write enable */
+#define DBCR0_DAC2R 0x00020000 /* DAC 2 Read enable */
+#define DBCR0_DAC2W 0x00010000 /* DAC 2 Write enable */
+#define DBCR0_RET 0x00008000 /* Return Debug Event */
+#define DBCR0_CIRPT 0x00000040 /* Critical Interrupt Taken Event */
+#define DBCR0_CRET 0x00000020 /* Critical Return Debug Event */
+#define DBCR0_FT 0x00000001 /* Freeze Timers on debug event */
+
+/* Bit definitions related to the DBCR1. */
+#define DBCR1_IAC12M 0x00800000 /* Instr Addr 1-2 range enable */
+#define DBCR1_IAC12MX 0x00C00000 /* Instr Addr 1-2 range eXclusive */
+#define DBCR1_IAC12AT 0x00010000 /* Instr Addr 1-2 range Toggle */
+#define DBCR1_IAC34M 0x00000080 /* Instr Addr 3-4 range enable */
+#define DBCR1_IAC34MX 0x000000C0 /* Instr Addr 3-4 range eXclusive */
+#define DBCR1_IAC34AT 0x00000001 /* Instr Addr 3-4 range Toggle */
+
+/* Bit definitions related to the DBCR2. */
+#define DBCR2_DAC12M 0x00800000 /* DAC 1-2 range enable */
+#define DBCR2_DAC12MX 0x00C00000 /* DAC 1-2 range eXclusive */
+#define DBCR2_DAC12A 0x00200000 /* DAC 1-2 Asynchronous */
+#endif
/* Bit definitions related to the TCR. */
#define TCR_WP(x) (((x)&0x3)<<30) /* WDT Period */
#define L1CSR1_ICFI 0x00000002 /* Instr Cache Flash Invalidate */
#define L1CSR1_ICE 0x00000001 /* Instr Cache Enable */
+/* Bit definitions for L2CSR0. */
+#define L2CSR0_L2E 0x80000000 /* L2 Cache Enable */
+#define L2CSR0_L2PE 0x40000000 /* L2 Cache Parity/ECC Enable */
+#define L2CSR0_L2WP 0x1c000000 /* L2 I/D Way Partioning */
+#define L2CSR0_L2CM 0x03000000 /* L2 Cache Coherency Mode */
+#define L2CSR0_L2FI 0x00200000 /* L2 Cache Flash Invalidate */
+#define L2CSR0_L2IO 0x00100000 /* L2 Cache Instruction Only */
+#define L2CSR0_L2DO 0x00010000 /* L2 Cache Data Only */
+#define L2CSR0_L2REP 0x00003000 /* L2 Line Replacement Algo */
+#define L2CSR0_L2FL 0x00000800 /* L2 Cache Flush */
+#define L2CSR0_L2LFC 0x00000400 /* L2 Cache Lock Flash Clear */
+#define L2CSR0_L2LOA 0x00000080 /* L2 Cache Lock Overflow Allocate */
+#define L2CSR0_L2LO 0x00000020 /* L2 Cache Lock Overflow */
+
/* Bit definitions for SGR. */
#define SGR_NORMAL 0 /* Speculative fetching allowed. */
#define SGR_GUARDED 1 /* Speculative fetching disallowed. */
#include <linux/stringify.h>
-#ifdef __powerpc64__
+#if defined(__powerpc64__) || defined(CONFIG_PPC_E500MC)
#define __SUBARCH_HAS_LWSYNC
#endif
projects / linux-2.6-omap-h63xx.git / commitdiff