endif
config ARCH_GUMSTIX
- bool "Gumstix XScale boards"
+ bool "Gumstix XScale 255 boards"
+ select PXA25x
help
- Say Y here if you intend to run this kernel on a
- Gumstix Full Function Minature Computer.
+ Say Y here if you intend to run this kernel on
+ Basix, Connex, ws-200ax, ws-400ax systems
-config MACH_GUMSTIX_F
- bool "Basix, Connex, ws-200ax, ws-400ax systems"
+choice
+ prompt "Gumstix Carrier/Expansion Board"
depends on ARCH_GUMSTIX
- select PXA25x
+
+config GUMSTIX_AM200EPD
+ bool "Enable AM200EPD board support"
+
+endchoice
+
+config MACH_INTELMOTE2
+ bool "Intel Mote 2 Platform"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
config ARCH_LUBBOCK
bool "Intel DBPXA250 Development Platform"
endchoice
-config MACH_AM200EPD
- depends on MACH_GUMSTIX_F
- bool "Enable AM200EPD board support"
-
config PXA_EZX
bool "Motorola EZX Platform"
select PXA27x
# Specific board support
obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o
-obj-$(CONFIG_MACH_AM200EPD) += am200epd.o
+obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
obj-$(CONFIG_PXA_EZX) += ezx.o
+obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
+
# Support for blinky lights
led-y := leds.o
led-$(CONFIG_ARCH_LUBBOCK) += leds-lubbock.o
GPIO16_GPIO,
};
-static int __init am200_init(void)
+int __init am200_init(void)
{
int ret;
module_param(panel_type, uint, 0);
MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97");
-module_init(am200_init);
-
MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
MODULE_AUTHOR("Jaya Kumar");
MODULE_LICENSE("GPL");
static struct pxafb_mach_info generic_stn_320x240 = {
.modes = &generic_stn_320x240_mode,
.num_modes = 1,
- .lccr0 = 0,
- .lccr3 = (LCCR3_PixClkDiv(0x03) |
- LCCR3_Acb(0xff) |
- LCCR3_PCP),
+ .lcd_conn = LCD_COLOR_STN_8BPP | LCD_PCLK_EDGE_FALL |\
+ LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info generic_tft_640x480 = {
.modes = &generic_tft_640x480_mode,
.num_modes = 1,
- .lccr0 = (LCCR0_PAS),
- .lccr3 = (LCCR3_PixClkDiv(0x01) |
- LCCR3_Acb(0xff) |
- LCCR3_PCP),
+ .lcd_conn = LCD_COLOR_TFT_8BPP | LCD_PCLK_EDGE_FALL |\
+ LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info generic_crt_640x480 = {
.modes = &generic_crt_640x480_mode,
.num_modes = 1,
- .lccr0 = (LCCR0_PAS),
- .lccr3 = (LCCR3_PixClkDiv(0x01) |
- LCCR3_Acb(0xff)),
+ .lcd_conn = LCD_COLOR_TFT_8BPP | LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info generic_crt_800x600 = {
.modes = &generic_crt_800x600_mode,
.num_modes = 1,
- .lccr0 = (LCCR0_PAS),
- .lccr3 = (LCCR3_PixClkDiv(0x02) |
- LCCR3_Acb(0xff)),
+ .lcd_conn = LCD_COLOR_TFT_8BPP | LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info generic_tft_320x240 = {
.modes = &generic_tft_320x240_mode,
.num_modes = 1,
- .lccr0 = (LCCR0_PAS),
- .lccr3 = (LCCR3_PixClkDiv(0x06) |
- LCCR3_Acb(0xff) |
- LCCR3_PCP),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info generic_stn_640x480 = {
.modes = &generic_stn_640x480_mode,
.num_modes = 1,
- .lccr0 = 0,
- .lccr3 = (LCCR3_PixClkDiv(0x02) |
- LCCR3_Acb(0xff)),
+ .lcd_conn = LCD_COLOR_STN_8BPP | LCD_AC_BIAS_FREQ(0xff),
.cmap_inverse = 0,
.cmap_static = 0,
};
static struct pxafb_mach_info e400_pxafb_mach_info = {
.modes = &e400_pxafb_mode_info,
.num_modes = 1,
- .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+ .lcd_conn = LCD_COLOR_TFT_16BPP,
.lccr3 = 0,
.pxafb_backlight_power = NULL,
};
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/pwm_backlight.h>
+#include <linux/input.h>
#include <asm/setup.h>
#include <mach/pxafb.h>
#include <mach/ohci.h>
#include <mach/i2c.h>
#include <mach/hardware.h>
+#include <mach/pxa27x_keypad.h>
#include <mach/mfp-pxa27x.h>
#include <mach/pxa-regs.h>
GPIO44_BTUART_CTS,
GPIO45_BTUART_RTS,
- /* STUART */
- GPIO46_STUART_RXD,
- GPIO47_STUART_TXD,
-
- /* For A780 support (connected with Neptune GSM chip) */
- GPIO30_USB_P3_2, /* ICL_TXENB */
- GPIO31_USB_P3_6, /* ICL_VPOUT */
- GPIO90_USB_P3_5, /* ICL_VPIN */
- GPIO91_USB_P3_1, /* ICL_XRXD */
- GPIO56_USB_P3_4, /* ICL_VMOUT */
- GPIO113_USB_P3_3, /* /ICL_VMIN */
-
/* I2C */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
+
+ /* PCAP SSP */
+ GPIO29_SSP1_SCLK,
+ GPIO25_SSP1_TXD,
+ GPIO26_SSP1_RXD,
+ GPIO24_GPIO, /* pcap chip select */
+ GPIO1_GPIO, /* pcap interrupt */
+ GPIO4_GPIO, /* WDI_AP */
+ GPIO55_GPIO, /* SYS_RESTART */
+
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO11_GPIO, /* mmc detect */
+
+ /* usb to external transceiver */
+ GPIO34_USB_P2_2,
+ GPIO35_USB_P2_1,
+ GPIO36_USB_P2_4,
+ GPIO39_USB_P2_6,
+ GPIO40_USB_P2_5,
+ GPIO53_USB_P2_3,
+
+ /* usb to Neptune GSM chip */
+ GPIO30_USB_P3_2,
+ GPIO31_USB_P3_6,
+ GPIO90_USB_P3_5,
+ GPIO91_USB_P3_1,
+ GPIO56_USB_P3_4,
+ GPIO113_USB_P3_3,
+};
+
+#if defined(CONFIG_MACH_EZX_A780) || defined(CONFIG_MACH_EZX_E680)
+static unsigned long gen1_pin_config[] __initdata = {
+ /* flip / lockswitch */
+ GPIO12_GPIO,
+
+ /* bluetooth (bcm2035) */
+ GPIO14_GPIO | WAKEUP_ON_LEVEL_HIGH, /* HOSTWAKE */
+ GPIO48_GPIO, /* RESET */
+ GPIO28_GPIO, /* WAKEUP */
+
+ /* Neptune handshake */
+ GPIO0_GPIO | WAKEUP_ON_LEVEL_HIGH, /* BP_RDY */
+ GPIO57_GPIO, /* AP_RDY */
+ GPIO13_GPIO | WAKEUP_ON_LEVEL_HIGH, /* WDI */
+ GPIO3_GPIO | WAKEUP_ON_LEVEL_HIGH, /* WDI2 */
+ GPIO82_GPIO, /* RESET */
+ GPIO99_GPIO, /* TC_MM_EN */
+
+ /* sound */
+ GPIO52_SSP3_SCLK,
+ GPIO83_SSP3_SFRM,
+ GPIO81_SSP3_TXD,
+ GPIO89_SSP3_RXD,
+
+ /* ssp2 pins to in */
+ GPIO22_GPIO, /* SSP2_SCLK */
+ GPIO37_GPIO, /* SSP2_SFRM */
+ GPIO38_GPIO, /* SSP2_TXD */
+ GPIO88_GPIO, /* SSP2_RXD */
+
+ /* camera */
+ GPIO23_CIF_MCLK,
+ GPIO54_CIF_PCLK,
+ GPIO85_CIF_LV,
+ GPIO84_CIF_FV,
+ GPIO27_CIF_DD_0,
+ GPIO114_CIF_DD_1,
+ GPIO51_CIF_DD_2,
+ GPIO115_CIF_DD_3,
+ GPIO95_CIF_DD_4,
+ GPIO94_CIF_DD_5,
+ GPIO17_CIF_DD_6,
+ GPIO108_CIF_DD_7,
+ GPIO50_GPIO, /* CAM_EN */
+ GPIO19_GPIO, /* CAM_RST */
+
+ /* EMU */
+ GPIO120_GPIO, /* EMU_MUX1 */
+ GPIO119_GPIO, /* EMU_MUX2 */
+ GPIO86_GPIO, /* SNP_INT_CTL */
+ GPIO87_GPIO, /* SNP_INT_IN */
+};
+#endif
+
+#if defined(CONFIG_MACH_EZX_A1200) || defined(CONFIG_MACH_EZX_A910) || \
+ defined(CONFIG_MACH_EZX_E2) || defined(CONFIG_MACH_EZX_E6)
+static unsigned long gen2_pin_config[] __initdata = {
+ /* flip / lockswitch */
+ GPIO15_GPIO,
+
+ /* EOC */
+ GPIO10_GPIO,
+
+ /* bluetooth (bcm2045) */
+ GPIO13_GPIO | WAKEUP_ON_LEVEL_HIGH, /* HOSTWAKE */
+ GPIO37_GPIO, /* RESET */
+ GPIO57_GPIO, /* WAKEUP */
+
+ /* Neptune handshake */
+ GPIO0_GPIO | WAKEUP_ON_LEVEL_HIGH, /* BP_RDY */
+ GPIO96_GPIO, /* AP_RDY */
+ GPIO3_GPIO | WAKEUP_ON_LEVEL_HIGH, /* WDI */
+ GPIO116_GPIO, /* RESET */
+ GPIO41_GPIO, /* BP_FLASH */
+
+ /* sound */
+ GPIO52_SSP3_SCLK,
+ GPIO83_SSP3_SFRM,
+ GPIO81_SSP3_TXD,
+ GPIO82_SSP3_RXD,
+
+ /* ssp2 pins to in */
+ GPIO22_GPIO, /* SSP2_SCLK */
+ GPIO14_GPIO, /* SSP2_SFRM */
+ GPIO38_GPIO, /* SSP2_TXD */
+ GPIO88_GPIO, /* SSP2_RXD */
+
+ /* camera */
+ GPIO23_CIF_MCLK,
+ GPIO54_CIF_PCLK,
+ GPIO85_CIF_LV,
+ GPIO84_CIF_FV,
+ GPIO27_CIF_DD_0,
+ GPIO114_CIF_DD_1,
+ GPIO51_CIF_DD_2,
+ GPIO115_CIF_DD_3,
+ GPIO95_CIF_DD_4,
+ GPIO48_CIF_DD_5,
+ GPIO93_CIF_DD_6,
+ GPIO12_CIF_DD_7,
+ GPIO50_GPIO, /* CAM_EN */
+ GPIO28_GPIO, /* CAM_RST */
+ GPIO17_GPIO, /* CAM_FLASH */
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_A780
+static unsigned long a780_pin_config[] __initdata = {
+ /* keypad */
+ GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+
+ /* attenuate sound */
+ GPIO96_GPIO,
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_E680
+static unsigned long e680_pin_config[] __initdata = {
+ /* keypad */
+ GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO96_KP_DKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_DKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_DKIN_5 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+
+ /* MIDI */
+ GPIO79_GPIO, /* VA_SEL_BUL */
+ GPIO80_GPIO, /* FLT_SEL_BUL */
+ GPIO78_GPIO, /* MIDI_RESET */
+ GPIO33_GPIO, /* MIDI_CS */
+ GPIO15_GPIO, /* MIDI_IRQ */
+ GPIO49_GPIO, /* MIDI_NPWE */
+ GPIO18_GPIO, /* MIDI_RDY */
+
+ /* leds */
+ GPIO46_GPIO,
+ GPIO47_GPIO,
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_A1200
+static unsigned long a1200_pin_config[] __initdata = {
+ /* keypad */
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+ GPIO108_KP_MKOUT_5,
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_A910
+static unsigned long a910_pin_config[] __initdata = {
+ /* keypad */
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+ GPIO108_KP_MKOUT_5,
+
+ /* WLAN */
+ GPIO89_GPIO, /* RESET */
+ GPIO33_GPIO, /* WAKEUP */
+ GPIO94_GPIO | WAKEUP_ON_LEVEL_HIGH, /* HOSTWAKE */
+
+ /* MMC CS */
+ GPIO20_GPIO,
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_E2
+static unsigned long e2_pin_config[] __initdata = {
+ /* keypad */
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+ GPIO108_KP_MKOUT_5,
+};
+#endif
+
+#ifdef CONFIG_MACH_EZX_E6
+static unsigned long e6_pin_config[] __initdata = {
+ /* keypad */
+ GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO101_KP_MKIN_1 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO102_KP_MKIN_2 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO97_KP_MKIN_3 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO98_KP_MKIN_4 | WAKEUP_ON_LEVEL_HIGH,
+ GPIO103_KP_MKOUT_0,
+ GPIO104_KP_MKOUT_1,
+ GPIO105_KP_MKOUT_2,
+ GPIO106_KP_MKOUT_3,
+ GPIO107_KP_MKOUT_4,
+ GPIO108_KP_MKOUT_5,
+};
+#endif
+
+/* KEYPAD */
+#ifdef CONFIG_MACH_EZX_A780
+static unsigned int a780_key_map[] = {
+ KEY(0, 0, KEY_SEND),
+ KEY(0, 1, KEY_BACK),
+ KEY(0, 2, KEY_END),
+ KEY(0, 3, KEY_PAGEUP),
+ KEY(0, 4, KEY_UP),
+
+ KEY(1, 0, KEY_NUMERIC_1),
+ KEY(1, 1, KEY_NUMERIC_2),
+ KEY(1, 2, KEY_NUMERIC_3),
+ KEY(1, 3, KEY_SELECT),
+ KEY(1, 4, KEY_KPENTER),
+
+ KEY(2, 0, KEY_NUMERIC_4),
+ KEY(2, 1, KEY_NUMERIC_5),
+ KEY(2, 2, KEY_NUMERIC_6),
+ KEY(2, 3, KEY_RECORD),
+ KEY(2, 4, KEY_LEFT),
+
+ KEY(3, 0, KEY_NUMERIC_7),
+ KEY(3, 1, KEY_NUMERIC_8),
+ KEY(3, 2, KEY_NUMERIC_9),
+ KEY(3, 3, KEY_HOME),
+ KEY(3, 4, KEY_RIGHT),
+
+ KEY(4, 0, KEY_NUMERIC_STAR),
+ KEY(4, 1, KEY_NUMERIC_0),
+ KEY(4, 2, KEY_NUMERIC_POUND),
+ KEY(4, 3, KEY_PAGEDOWN),
+ KEY(4, 4, KEY_DOWN),
+};
+
+static struct pxa27x_keypad_platform_data a780_keypad_platform_data = {
+ .matrix_key_rows = 5,
+ .matrix_key_cols = 5,
+ .matrix_key_map = a780_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(a780_key_map),
+
+ .direct_key_map = { KEY_CAMERA },
+ .direct_key_num = 1,
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_A780 */
+
+#ifdef CONFIG_MACH_EZX_E680
+static unsigned int e680_key_map[] = {
+ KEY(0, 0, KEY_UP),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_RESERVED),
+ KEY(0, 3, KEY_SEND),
+
+ KEY(1, 0, KEY_DOWN),
+ KEY(1, 1, KEY_LEFT),
+ KEY(1, 2, KEY_PAGEUP),
+ KEY(1, 3, KEY_PAGEDOWN),
+
+ KEY(2, 0, KEY_RESERVED),
+ KEY(2, 1, KEY_RESERVED),
+ KEY(2, 2, KEY_RESERVED),
+ KEY(2, 3, KEY_KPENTER),
+};
+
+static struct pxa27x_keypad_platform_data e680_keypad_platform_data = {
+ .matrix_key_rows = 3,
+ .matrix_key_cols = 4,
+ .matrix_key_map = e680_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(e680_key_map),
+
+ .direct_key_map = {
+ KEY_CAMERA,
+ KEY_RESERVED,
+ KEY_RESERVED,
+ KEY_F1,
+ KEY_CANCEL,
+ KEY_F2,
+ },
+ .direct_key_num = 6,
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_E680 */
+
+#ifdef CONFIG_MACH_EZX_A1200
+static unsigned int a1200_key_map[] = {
+ KEY(0, 0, KEY_RESERVED),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_PAGEDOWN),
+ KEY(0, 3, KEY_RESERVED),
+ KEY(0, 4, KEY_RESERVED),
+ KEY(0, 5, KEY_RESERVED),
+
+ KEY(1, 0, KEY_RESERVED),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 2, KEY_CAMERA),
+ KEY(1, 3, KEY_RESERVED),
+ KEY(1, 4, KEY_RESERVED),
+ KEY(1, 5, KEY_RESERVED),
+
+ KEY(2, 0, KEY_RESERVED),
+ KEY(2, 1, KEY_KPENTER),
+ KEY(2, 2, KEY_RECORD),
+ KEY(2, 3, KEY_RESERVED),
+ KEY(2, 4, KEY_RESERVED),
+ KEY(2, 5, KEY_SELECT),
+
+ KEY(3, 0, KEY_RESERVED),
+ KEY(3, 1, KEY_UP),
+ KEY(3, 2, KEY_SEND),
+ KEY(3, 3, KEY_RESERVED),
+ KEY(3, 4, KEY_RESERVED),
+ KEY(3, 5, KEY_RESERVED),
+
+ KEY(4, 0, KEY_RESERVED),
+ KEY(4, 1, KEY_LEFT),
+ KEY(4, 2, KEY_PAGEUP),
+ KEY(4, 3, KEY_RESERVED),
+ KEY(4, 4, KEY_RESERVED),
+ KEY(4, 5, KEY_RESERVED),
+};
+
+static struct pxa27x_keypad_platform_data a1200_keypad_platform_data = {
+ .matrix_key_rows = 5,
+ .matrix_key_cols = 6,
+ .matrix_key_map = a1200_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(a1200_key_map),
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_A1200 */
+
+#ifdef CONFIG_MACH_EZX_E6
+static unsigned int e6_key_map[] = {
+ KEY(0, 0, KEY_RESERVED),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_PAGEDOWN),
+ KEY(0, 3, KEY_RESERVED),
+ KEY(0, 4, KEY_RESERVED),
+ KEY(0, 5, KEY_NEXTSONG),
+
+ KEY(1, 0, KEY_RESERVED),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 2, KEY_PROG1),
+ KEY(1, 3, KEY_RESERVED),
+ KEY(1, 4, KEY_RESERVED),
+ KEY(1, 5, KEY_RESERVED),
+
+ KEY(2, 0, KEY_RESERVED),
+ KEY(2, 1, KEY_ENTER),
+ KEY(2, 2, KEY_CAMERA),
+ KEY(2, 3, KEY_RESERVED),
+ KEY(2, 4, KEY_RESERVED),
+ KEY(2, 5, KEY_WWW),
+
+ KEY(3, 0, KEY_RESERVED),
+ KEY(3, 1, KEY_UP),
+ KEY(3, 2, KEY_SEND),
+ KEY(3, 3, KEY_RESERVED),
+ KEY(3, 4, KEY_RESERVED),
+ KEY(3, 5, KEY_PLAYPAUSE),
+
+ KEY(4, 0, KEY_RESERVED),
+ KEY(4, 1, KEY_LEFT),
+ KEY(4, 2, KEY_PAGEUP),
+ KEY(4, 3, KEY_RESERVED),
+ KEY(4, 4, KEY_RESERVED),
+ KEY(4, 5, KEY_PREVIOUSSONG),
+};
+
+static struct pxa27x_keypad_platform_data e6_keypad_platform_data = {
+ .matrix_key_rows = 5,
+ .matrix_key_cols = 6,
+ .matrix_key_map = e6_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(e6_key_map),
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_E6 */
+
+#ifdef CONFIG_MACH_EZX_A910
+static unsigned int a910_key_map[] = {
+ KEY(0, 0, KEY_NUMERIC_6),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_PAGEDOWN),
+ KEY(0, 3, KEY_KPENTER),
+ KEY(0, 4, KEY_NUMERIC_5),
+ KEY(0, 5, KEY_CAMERA),
+
+ KEY(1, 0, KEY_NUMERIC_8),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 2, KEY_RESERVED),
+ KEY(1, 3, KEY_F1), /* Left SoftKey */
+ KEY(1, 4, KEY_NUMERIC_STAR),
+ KEY(1, 5, KEY_RESERVED),
+
+ KEY(2, 0, KEY_NUMERIC_7),
+ KEY(2, 1, KEY_NUMERIC_9),
+ KEY(2, 2, KEY_RECORD),
+ KEY(2, 3, KEY_F2), /* Right SoftKey */
+ KEY(2, 4, KEY_BACK),
+ KEY(2, 5, KEY_SELECT),
+
+ KEY(3, 0, KEY_NUMERIC_2),
+ KEY(3, 1, KEY_UP),
+ KEY(3, 2, KEY_SEND),
+ KEY(3, 3, KEY_NUMERIC_0),
+ KEY(3, 4, KEY_NUMERIC_1),
+ KEY(3, 5, KEY_RECORD),
+
+ KEY(4, 0, KEY_NUMERIC_4),
+ KEY(4, 1, KEY_LEFT),
+ KEY(4, 2, KEY_PAGEUP),
+ KEY(4, 3, KEY_NUMERIC_POUND),
+ KEY(4, 4, KEY_NUMERIC_3),
+ KEY(4, 5, KEY_RESERVED),
};
-static void __init ezx_init(void)
+static struct pxa27x_keypad_platform_data a910_keypad_platform_data = {
+ .matrix_key_rows = 5,
+ .matrix_key_cols = 6,
+ .matrix_key_map = a910_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(a910_key_map),
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_A910 */
+
+#ifdef CONFIG_MACH_EZX_E2
+static unsigned int e2_key_map[] = {
+ KEY(0, 0, KEY_NUMERIC_6),
+ KEY(0, 1, KEY_RIGHT),
+ KEY(0, 2, KEY_NUMERIC_9),
+ KEY(0, 3, KEY_NEXTSONG),
+ KEY(0, 4, KEY_NUMERIC_5),
+ KEY(0, 5, KEY_F1), /* Left SoftKey */
+
+ KEY(1, 0, KEY_NUMERIC_8),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 2, KEY_RESERVED),
+ KEY(1, 3, KEY_PAGEUP),
+ KEY(1, 4, KEY_NUMERIC_STAR),
+ KEY(1, 5, KEY_F2), /* Right SoftKey */
+
+ KEY(2, 0, KEY_NUMERIC_7),
+ KEY(2, 1, KEY_KPENTER),
+ KEY(2, 2, KEY_RECORD),
+ KEY(2, 3, KEY_PAGEDOWN),
+ KEY(2, 4, KEY_BACK),
+ KEY(2, 5, KEY_NUMERIC_0),
+
+ KEY(3, 0, KEY_NUMERIC_2),
+ KEY(3, 1, KEY_UP),
+ KEY(3, 2, KEY_SEND),
+ KEY(3, 3, KEY_PLAYPAUSE),
+ KEY(3, 4, KEY_NUMERIC_1),
+ KEY(3, 5, KEY_SOUND), /* Music SoftKey */
+
+ KEY(4, 0, KEY_NUMERIC_4),
+ KEY(4, 1, KEY_LEFT),
+ KEY(4, 2, KEY_NUMERIC_POUND),
+ KEY(4, 3, KEY_PREVIOUSSONG),
+ KEY(4, 4, KEY_NUMERIC_3),
+ KEY(4, 5, KEY_RESERVED),
+};
+
+static struct pxa27x_keypad_platform_data e2_keypad_platform_data = {
+ .matrix_key_rows = 5,
+ .matrix_key_cols = 6,
+ .matrix_key_map = e2_key_map,
+ .matrix_key_map_size = ARRAY_SIZE(e2_key_map),
+
+ .debounce_interval = 30,
+};
+#endif /* CONFIG_MACH_EZX_E2 */
+
+#ifdef CONFIG_MACH_EZX_A780
+static void __init a780_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen1_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(a780_pin_config));
+
pxa_set_i2c_info(NULL);
- if (machine_is_ezx_a780() || machine_is_ezx_e680())
- set_pxa_fb_info(&ezx_fb_info_1);
- else
- set_pxa_fb_info(&ezx_fb_info_2);
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
+ set_pxa_fb_info(&ezx_fb_info_1);
-static void __init ezx_fixup(struct machine_desc *desc, struct tag *tags,
- char **cmdline, struct meminfo *mi)
-{
- /* We have two ram chips. First one with 32MB at 0xA0000000 and a second
- * 16MB one at 0xAC000000
- */
- mi->nr_banks = 2;
- mi->bank[0].start = 0xa0000000;
- mi->bank[0].node = 0;
- mi->bank[0].size = (32*1024*1024);
- mi->bank[1].start = 0xac000000;
- mi->bank[1].node = 1;
- mi->bank[1].size = (16*1024*1024);
+ pxa_set_keypad_info(&a780_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
}
-#ifdef CONFIG_MACH_EZX_A780
MACHINE_START(EZX_A780, "Motorola EZX A780")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = a780_init,
MACHINE_END
#endif
#ifdef CONFIG_MACH_EZX_E680
+static struct i2c_board_info __initdata e680_i2c_board_info[] = {
+ { I2C_BOARD_INFO("tea5767", 0x81) },
+};
+
+static void __init e680_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen1_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(e680_pin_config));
+
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(e680_i2c_board_info));
+
+ set_pxa_fb_info(&ezx_fb_info_1);
+
+ pxa_set_keypad_info(&e680_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
MACHINE_START(EZX_E680, "Motorola EZX E680")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = e680_init,
MACHINE_END
#endif
#ifdef CONFIG_MACH_EZX_A1200
+static struct i2c_board_info __initdata a1200_i2c_board_info[] = {
+ { I2C_BOARD_INFO("tea5767", 0x81) },
+};
+
+static void __init a1200_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen2_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(a1200_pin_config));
+
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(a1200_i2c_board_info));
+
+ set_pxa_fb_info(&ezx_fb_info_2);
+
+ pxa_set_keypad_info(&a1200_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
MACHINE_START(EZX_A1200, "Motorola EZX A1200")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = a1200_init,
MACHINE_END
#endif
#ifdef CONFIG_MACH_EZX_A910
+static void __init a910_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen2_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(a910_pin_config));
+
+ pxa_set_i2c_info(NULL);
+
+ set_pxa_fb_info(&ezx_fb_info_2);
+
+ pxa_set_keypad_info(&a910_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
MACHINE_START(EZX_A910, "Motorola EZX A910")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = a910_init,
MACHINE_END
#endif
#ifdef CONFIG_MACH_EZX_E6
+static struct i2c_board_info __initdata e6_i2c_board_info[] = {
+ { I2C_BOARD_INFO("tea5767", 0x81) },
+};
+
+static void __init e6_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen2_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(e6_pin_config));
+
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(e6_i2c_board_info));
+
+ set_pxa_fb_info(&ezx_fb_info_2);
+
+ pxa_set_keypad_info(&e6_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
MACHINE_START(EZX_E6, "Motorola EZX E6")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = e6_init,
MACHINE_END
#endif
#ifdef CONFIG_MACH_EZX_E2
+static struct i2c_board_info __initdata e2_i2c_board_info[] = {
+ { I2C_BOARD_INFO("tea5767", 0x81) },
+};
+
+static void __init e2_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(ezx_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(gen2_pin_config));
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(e2_pin_config));
+
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(e2_i2c_board_info));
+
+ set_pxa_fb_info(&ezx_fb_info_2);
+
+ pxa_set_keypad_info(&e2_keypad_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
MACHINE_START(EZX_E2, "Motorola EZX E2")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = ezx_fixup,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
.timer = &pxa_timer,
- .init_machine = &ezx_init,
+ .init_machine = e2_init,
MACHINE_END
#endif
GPIO8_MMC_CS0,
};
+int __attribute__((weak)) am200_init(void)
+{
+ return 0;
+}
+
+static void __init carrier_board_init(void)
+{
+ /*
+ * put carrier/expansion board init here if
+ * they cannot be detected programatically
+ */
+ am200_init();
+}
+
static void __init gumstix_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(gumstix_pin_config));
gumstix_udc_init();
gumstix_mmc_init();
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+ carrier_board_init();
}
MACHINE_START(GUMSTIX, "Gumstix")
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/imote2.c
+ *
+ * Author: Ed C. Epp
+ * Created: Nov 05, 2002
+ * Copyright: Intel Corp.
+ *
+ * Modified 2008: Jonathan Cameron
+ *
+ * The Imote2 is a wireless sensor node platform sold
+ * by Crossbow (www.xbow.com).
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/machine.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/i2c.h>
+#include <linux/mfd/da903x.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <mach/i2c.h>
+#include <mach/pxa-regs.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa27x.h>
+#include <mach/regs-ssp.h>
+#include <mach/udc.h>
+#include <mach/mmc.h>
+#include <mach/pxa2xx_spi.h>
+#include <mach/pxa27x-udc.h>
+
+#include "devices.h"
+#include "generic.h"
+
+static unsigned long imote2_pin_config[] __initdata = {
+
+ /* Device Identification for wakeup*/
+ GPIO102_GPIO,
+
+ /* Button */
+ GPIO91_GPIO,
+
+ /* DA9030 */
+ GPIO1_GPIO,
+
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO112_MMC_CMD,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+
+ /* 802.15.4 radio - driver out of mainline */
+ GPIO22_GPIO, /* CC_RSTN */
+ GPIO114_GPIO, /* CC_FIFO */
+ GPIO116_GPIO, /* CC_CCA */
+ GPIO0_GPIO, /* CC_FIFOP */
+ GPIO16_GPIO, /* CCSFD */
+ GPIO39_GPIO, /* CSn */
+ GPIO115_GPIO, /* Power enable */
+
+ /* I2C */
+ GPIO117_I2C_SCL,
+ GPIO118_I2C_SDA,
+
+ /* SSP 3 - 802.15.4 radio */
+ GPIO39_GPIO, /* Chip Select */
+ GPIO34_SSP3_SCLK,
+ GPIO35_SSP3_TXD,
+ GPIO41_SSP3_RXD,
+
+ /* SSP 2 - to daughter boards */
+ GPIO37_GPIO, /* Chip Select */
+ GPIO36_SSP2_SCLK,
+ GPIO38_SSP2_TXD,
+ GPIO11_SSP2_RXD,
+
+ /* SSP 1 - to daughter boards */
+ GPIO24_GPIO, /* Chip Select */
+ GPIO23_SSP1_SCLK,
+ GPIO25_SSP1_TXD,
+ GPIO26_SSP1_RXD,
+
+ /* BTUART Basic Connector*/
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO44_BTUART_CTS,
+ GPIO45_BTUART_RTS,
+
+ /* STUART Serial console via debug board*/
+ GPIO46_STUART_RXD,
+ GPIO47_STUART_TXD,
+
+ /* Basic sensor board */
+ GPIO96_GPIO, /* accelerometer interrupt */
+ GPIO99_GPIO, /* ADC interrupt */
+
+ /* Connector pins specified as gpios */
+ GPIO94_GPIO, /* large basic connector pin 14 */
+ GPIO10_GPIO, /* large basic connector pin 23 */
+
+ /* LEDS */
+ GPIO103_GPIO, /* red led */
+ GPIO104_GPIO, /* green led */
+ GPIO105_GPIO, /* blue led */
+};
+
+static struct gpio_led imote2_led_pins[] = {
+ {
+ .name = "imote2:red",
+ .gpio = 103,
+ .active_low = 1,
+ }, {
+ .name = "imote2:green",
+ .gpio = 104,
+ .active_low = 1,
+ }, {
+ .name = "imote2:blue",
+ .gpio = 105,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data imote2_led_data = {
+ .num_leds = ARRAY_SIZE(imote2_led_pins),
+ .leds = imote2_led_pins,
+};
+
+static struct platform_device imote2_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &imote2_led_data,
+ },
+};
+
+/* Reverse engineered partly from Platformx drivers */
+enum imote2_ldos{
+ vcc_vref,
+ vcc_cc2420,
+ vcc_mica,
+ vcc_bt,
+ /* The two voltages available to sensor boards */
+ vcc_sensor_1_8,
+ vcc_sensor_3,
+
+ vcc_sram_ext, /* directly connected to the pxa271 */
+ vcc_pxa_pll,
+ vcc_pxa_usim, /* Reference voltage for certain gpios */
+ vcc_pxa_mem,
+ vcc_pxa_flash,
+ vcc_pxa_core, /*Dc-Dc buck not yet supported */
+ vcc_lcd,
+ vcc_bb,
+ vcc_bbio,
+ vcc_io, /* cc2420 802.15.4 radio and pxa vcc_io ?*/
+};
+
+/* The values of the various regulator constraints are obviously dependent
+ * on exactly what is wired to each ldo. Unfortunately this information is
+ * not generally available. More information has been requested from Xbow
+ * but as of yet they haven't been forthcoming.
+ *
+ * Some of these are clearly Stargate 2 related (no way of plugging
+ * in an lcd on the IM2 for example!).
+ */
+static struct regulator_init_data imote2_ldo_init_data[] = {
+ [vcc_bbio] = {
+ .constraints = { /* board default 1.8V */
+ .name = "vcc_bbio",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ },
+ },
+ [vcc_bb] = {
+ .constraints = { /* board default 2.8V */
+ .name = "vcc_bb",
+ .min_uV = 2700000,
+ .max_uV = 3000000,
+ },
+ },
+ [vcc_pxa_flash] = {
+ .constraints = {/* default is 1.8V */
+ .name = "vcc_pxa_flash",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ },
+ },
+ [vcc_cc2420] = { /* also vcc_io */
+ .constraints = {
+ /* board default is 2.8V */
+ .name = "vcc_cc2420",
+ .min_uV = 2700000,
+ .max_uV = 3300000,
+ },
+ },
+ [vcc_vref] = { /* Reference for what? */
+ .constraints = { /* default 1.8V */
+ .name = "vcc_vref",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ },
+ },
+ [vcc_sram_ext] = {
+ .constraints = { /* default 2.8V */
+ .name = "vcc_sram_ext",
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ },
+ },
+ [vcc_mica] = {
+ .constraints = { /* default 2.8V */
+ .name = "vcc_mica",
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ },
+ },
+ [vcc_bt] = {
+ .constraints = { /* default 2.8V */
+ .name = "vcc_bt",
+ .min_uV = 2800000,
+ .max_uV = 2800000,
+ },
+ },
+ [vcc_lcd] = {
+ .constraints = { /* default 2.8V */
+ .name = "vcc_lcd",
+ .min_uV = 2700000,
+ .max_uV = 3300000,
+ },
+ },
+ [vcc_io] = { /* Same or higher than everything
+ * bar vccbat and vccusb */
+ .constraints = { /* default 2.8V */
+ .name = "vcc_io",
+ .min_uV = 2692000,
+ .max_uV = 3300000,
+ },
+ },
+ [vcc_sensor_1_8] = {
+ .constraints = { /* default 1.8V */
+ .name = "vcc_sensor_1_8",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ },
+ },
+ [vcc_sensor_3] = { /* curiously default 2.8V */
+ .constraints = {
+ .name = "vcc_sensor_3",
+ .min_uV = 2800000,
+ .max_uV = 3000000,
+ },
+ },
+ [vcc_pxa_pll] = { /* 1.17V - 1.43V, default 1.3V*/
+ .constraints = {
+ .name = "vcc_pxa_pll",
+ .min_uV = 1170000,
+ .max_uV = 1430000,
+ },
+ },
+ [vcc_pxa_usim] = {
+ .constraints = { /* default 1.8V */
+ .name = "vcc_pxa_usim",
+ .min_uV = 1710000,
+ .max_uV = 2160000,
+ },
+ },
+ [vcc_pxa_mem] = {
+ .constraints = { /* default 1.8V */
+ .name = "vcc_pxa_mem",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ },
+ },
+};
+
+static struct da903x_subdev_info imote2_da9030_subdevs[] = {
+ {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO2,
+ .platform_data = &imote2_ldo_init_data[vcc_bbio],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO3,
+ .platform_data = &imote2_ldo_init_data[vcc_bb],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO4,
+ .platform_data = &imote2_ldo_init_data[vcc_pxa_flash],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO5,
+ .platform_data = &imote2_ldo_init_data[vcc_cc2420],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO6,
+ .platform_data = &imote2_ldo_init_data[vcc_vref],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO7,
+ .platform_data = &imote2_ldo_init_data[vcc_sram_ext],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO8,
+ .platform_data = &imote2_ldo_init_data[vcc_mica],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO9,
+ .platform_data = &imote2_ldo_init_data[vcc_bt],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO10,
+ .platform_data = &imote2_ldo_init_data[vcc_sensor_1_8],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO11,
+ .platform_data = &imote2_ldo_init_data[vcc_sensor_3],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO12,
+ .platform_data = &imote2_ldo_init_data[vcc_lcd],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO15,
+ .platform_data = &imote2_ldo_init_data[vcc_pxa_pll],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO17,
+ .platform_data = &imote2_ldo_init_data[vcc_pxa_usim],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO18,
+ .platform_data = &imote2_ldo_init_data[vcc_io],
+ }, {
+ .name = "da903x-regulator",
+ .id = DA9030_ID_LDO19,
+ .platform_data = &imote2_ldo_init_data[vcc_pxa_mem],
+ },
+};
+
+static struct da903x_platform_data imote2_da9030_pdata = {
+ .num_subdevs = ARRAY_SIZE(imote2_da9030_subdevs),
+ .subdevs = imote2_da9030_subdevs,
+};
+
+/* As the the imote2 doesn't currently have a conventional SD slot
+ * there is no option to hotplug cards, making all this rather simple
+ */
+static int imote2_mci_get_ro(struct device *dev)
+{
+ return 0;
+}
+
+/* Rather simple case as hotplugging not possible */
+static struct pxamci_platform_data imote2_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
+ .get_ro = imote2_mci_get_ro,
+};
+
+static struct mtd_partition imote2flash_partitions[] = {
+ {
+ .name = "Bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "Kernel",
+ .size = 0x00200000,
+ .offset = 0x00040000,
+ .mask_flags = 0,
+ }, {
+ .name = "Filesystem",
+ .size = 0x01DC0000,
+ .offset = 0x00240000,
+ .mask_flags = 0,
+ },
+};
+
+static struct resource flash_resources = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct flash_platform_data imote2_flash_data = {
+ .map_name = "cfi_probe",
+ .parts = imote2flash_partitions,
+ .nr_parts = ARRAY_SIZE(imote2flash_partitions),
+ .name = "PXA27xOnChipROM",
+ .width = 2,
+};
+
+static struct platform_device imote2_flash_device = {
+ .name = "pxa2xx-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &imote2_flash_data,
+ },
+ .resource = &flash_resources,
+ .num_resources = 1,
+};
+
+/* Some of the drivers here are out of kernel at the moment (parts of IIO)
+ * and it may be a while before they are in the mainline.
+ */
+static struct i2c_board_info __initdata imote2_i2c_board_info[] = {
+ { /* UCAM sensor board */
+ .type = "max1238",
+ .addr = 0x35,
+ }, { /* ITS400 Sensor board only */
+ .type = "max1363",
+ .addr = 0x34,
+ /* Through a nand gate - Also beware, on V2 sensor board the
+ * pull up resistors are missing.
+ */
+ .irq = IRQ_GPIO(99),
+ }, { /* ITS400 Sensor board only */
+ .type = "tsl2561",
+ .addr = 0x49,
+ /* Through a nand gate - Also beware, on V2 sensor board the
+ * pull up resistors are missing.
+ */
+ .irq = IRQ_GPIO(99),
+ }, { /* ITS400 Sensor board only */
+ .type = "tmp175",
+ .addr = 0x4A,
+ .irq = IRQ_GPIO(96),
+ },
+};
+
+static struct i2c_board_info __initdata imote2_pwr_i2c_board_info[] = {
+ {
+ .type = "da9030",
+ .addr = 0x49,
+ .platform_data = &imote2_da9030_pdata,
+ .irq = gpio_to_irq(1),
+ },
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_0_info = {
+ .num_chipselect = 1,
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_1_info = {
+ .num_chipselect = 1,
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_2_info = {
+ .num_chipselect = 1,
+};
+
+/* Patch posted by Eric Miao <eric.miao@marvell.com> will remove
+ * the need for these functions.
+ */
+static void spi1control(u32 command)
+{
+ gpio_set_value(24, command & PXA2XX_CS_ASSERT ? 0 : 1);
+};
+
+static void spi3control(u32 command)
+{
+ gpio_set_value(39, command & PXA2XX_CS_ASSERT ? 0 : 1);
+};
+
+static struct pxa2xx_spi_chip staccel_chip_info = {
+ .tx_threshold = 8,
+ .rx_threshold = 8,
+ .dma_burst_size = 8,
+ .timeout = 235,
+ .cs_control = spi1control,
+};
+
+static struct pxa2xx_spi_chip cc2420_info = {
+ .tx_threshold = 8,
+ .rx_threshold = 8,
+ .dma_burst_size = 8,
+ .timeout = 235,
+ .cs_control = spi3control,
+};
+
+static struct spi_board_info spi_board_info[] __initdata = {
+ { /* Driver in IIO */
+ .modalias = "lis3l02dq",
+ .max_speed_hz = 8000000,/* 8MHz max spi frequency at 3V */
+ .bus_num = 1,
+ .chip_select = 0,
+ .controller_data = &staccel_chip_info,
+ .irq = IRQ_GPIO(96),
+ }, { /* Driver out of kernel as it needs considerable rewriting */
+ .modalias = "cc2420",
+ .max_speed_hz = 6500000,
+ .bus_num = 3,
+ .chip_select = 0,
+ .controller_data = &cc2420_info,
+ },
+};
+
+static void im2_udc_command(int cmd)
+{
+ switch (cmd) {
+ case PXA2XX_UDC_CMD_CONNECT:
+ UP2OCR |= UP2OCR_HXOE | UP2OCR_DPPUE | UP2OCR_DPPUBE;
+ break;
+ case PXA2XX_UDC_CMD_DISCONNECT:
+ UP2OCR &= ~(UP2OCR_HXOE | UP2OCR_DPPUE | UP2OCR_DPPUBE);
+ break;
+ }
+}
+
+static struct pxa2xx_udc_mach_info imote2_udc_info __initdata = {
+ .udc_command = im2_udc_command,
+};
+
+static struct platform_device *imote2_devices[] = {
+ &imote2_flash_device,
+ &imote2_leds,
+};
+
+static struct i2c_pxa_platform_data i2c_pwr_pdata = {
+ .fast_mode = 1,
+};
+
+static struct i2c_pxa_platform_data i2c_pdata = {
+ .fast_mode = 1,
+};
+
+static void __init imote2_init(void)
+{
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(imote2_pin_config));
+ /* SPI chip select directions - all other directions should
+ * be handled by drivers.*/
+ gpio_direction_output(37, 0);
+ gpio_direction_output(24, 0);
+ gpio_direction_output(39, 0);
+
+ platform_add_devices(imote2_devices, ARRAY_SIZE(imote2_devices));
+
+ pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
+ pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
+ pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
+
+ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
+
+ i2c_register_board_info(0, imote2_i2c_board_info,
+ ARRAY_SIZE(imote2_i2c_board_info));
+ i2c_register_board_info(1, imote2_pwr_i2c_board_info,
+ ARRAY_SIZE(imote2_pwr_i2c_board_info));
+
+ pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
+ pxa_set_i2c_info(&i2c_pdata);
+
+ pxa_set_mci_info(&imote2_mci_platform_data);
+ pxa_set_udc_info(&imote2_udc_info);
+}
+
+MACHINE_START(INTELMOTE2, "IMOTE 2")
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = pxa_map_io,
+ .init_irq = pxa27x_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = imote2_init,
+ .boot_params = 0xA0000100,
+MACHINE_END
#define GPIO26_PRDY_nBSY_MD (GPIO26_PRDY_nBSY | GPIO_IN)
#define GPIO27_PRDY_nBSY_MD (GPIO27_PRDY_nBSY | GPIO_IN)
#define GPIO36_nCD_MD (GPIO36_nCD | GPIO_IN)
+
+/* for expansion boards that can't be programatically detected */
+extern int am200_init(void);
+
-#ifndef __ASM_ARCH_ZYLONITE_H
-#define __ASM_ARCH_ZYLONITE_H
+#ifndef __ASM_ARCH_LITTLETON_H
+#define __ASM_ARCH_LITTLETON_H
+
+#include <mach/gpio.h>
#define LITTLETON_ETH_PHYS 0x30000000
#define LITTLETON_GPIO_LCD_CS (17)
-#endif /* __ASM_ARCH_ZYLONITE_H */
+#define EXT0_GPIO_BASE (NR_BUILTIN_GPIO)
+#define EXT0_GPIO(x) (EXT0_GPIO_BASE + (x))
+
+#endif /* __ASM_ARCH_LITTLETON_H */
#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN)
#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN)
#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN)
+#define LCD_COLOR_TFT_8BPP ((8 << 4) | LCD_TYPE_COLOR_TFT)
#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT)
#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT)
#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL)
* in pxa27x and pxa3xx, initialize them to the same value or
* the larger one will be used
* 3. same to {rd,wr}_pulse_width
+ *
+ * 4. LCD_PCLK_EDGE_{RISE,FALL} controls the L_PCLK_WR polarity
+ * 5. sync & FB_SYNC_HOR_HIGH_ACT controls the L_LCLK_A0
+ * 6. sync & FB_SYNC_VERT_HIGH_ACT controls the L_LCLK_RD
*/
unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */
unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */
#define SMART_CMD(x) (SMART_CMD_WRITE_COMMAND | ((x) & 0xff))
#define SMART_DAT(x) (SMART_CMD_WRITE_DATA | ((x) & 0xff))
+
+/* SMART_DELAY() is introduced for software controlled delay primitive which
+ * can be inserted between command sequences, unused command 0x6 is used here
+ * and delay ranges from 0ms ~ 255ms
+ */
+#define SMART_CMD_DELAY (0x6 << 9)
+#define SMART_DELAY(ms) (SMART_CMD_DELAY | ((ms) & 0xff))
#endif /* __ASM_ARCH_REGS_LCD_H */
static inline void arch_decomp_setup(void)
{
- if (machine_is_littleton())
+ if (machine_is_littleton() || machine_is_intelmote2())
UART = STUART;
}
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/smc91x.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/mfd/da903x.h>
+#include <linux/i2c/max732x.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <mach/pxafb.h>
#include <mach/ssp.h>
#include <mach/pxa2xx_spi.h>
+#include <mach/i2c.h>
#include <mach/pxa27x_keypad.h>
#include <mach/pxa3xx_nand.h>
#include <mach/littleton.h>
static inline void littleton_init_nand(void) {}
#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */
+#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
+static struct led_info littleton_da9034_leds[] = {
+ [0] = {
+ .name = "littleton:keypad1",
+ .flags = DA9034_LED_RAMP,
+ },
+ [1] = {
+ .name = "littleton:keypad2",
+ .flags = DA9034_LED_RAMP,
+ },
+ [2] = {
+ .name = "littleton:vibra",
+ .flags = 0,
+ },
+};
+
+static struct da903x_subdev_info littleton_da9034_subdevs[] = {
+ {
+ .name = "da903x-led",
+ .id = DA9034_ID_LED_1,
+ .platform_data = &littleton_da9034_leds[0],
+ }, {
+ .name = "da903x-led",
+ .id = DA9034_ID_LED_2,
+ .platform_data = &littleton_da9034_leds[1],
+ }, {
+ .name = "da903x-led",
+ .id = DA9034_ID_VIBRA,
+ .platform_data = &littleton_da9034_leds[2],
+ }, {
+ .name = "da903x-backlight",
+ .id = DA9034_ID_WLED,
+ },
+};
+
+static struct da903x_platform_data littleton_da9034_info = {
+ .num_subdevs = ARRAY_SIZE(littleton_da9034_subdevs),
+ .subdevs = littleton_da9034_subdevs,
+};
+
+static struct max732x_platform_data littleton_max7320_info = {
+ .gpio_base = EXT0_GPIO_BASE,
+};
+
+static struct i2c_board_info littleton_i2c_info[] = {
+ [0] = {
+ .type = "da9034",
+ .addr = 0x34,
+ .platform_data = &littleton_da9034_info,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO18)),
+ },
+ [1] = {
+ .type = "max7320",
+ .addr = 0x50,
+ .platform_data = &littleton_max7320_info,
+ },
+};
+
+static void __init littleton_init_i2c(void)
+{
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(littleton_i2c_info));
+}
+#else
+static inline void littleton_init_i2c(void) {}
+#endif /* CONFIG_I2C_PXA || CONFIG_I2C_PXA_MODULE */
+
static void __init littleton_init(void)
{
/* initialize MFP configurations */
platform_device_register(&smc91x_device);
littleton_init_spi();
+ littleton_init_i2c();
littleton_init_lcd();
littleton_init_keypad();
littleton_init_nand();
.modes = toppoly_modes,
.num_modes = 1,
.fixed_modes = 1,
- .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
- .lccr3 = LCCR3_PixRsEdg,
+ .lcd_conn = LCD_COLOR_TFT_16BPP,
.pxafb_lcd_power = toppoly_lcd_power,
};
.modes = samsung_modes,
.num_modes = 1,
.fixed_modes = 1,
- .lccr0 = LCCR0_LDDALT | LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
- .lccr3 = LCCR3_PixFlEdg,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL |\
+ LCD_ALTERNATE_MAPPING,
.pxafb_lcd_power = samsung_lcd_power,
};
static struct pxafb_mach_info pcm990_fbinfo __initdata = {
.modes = &fb_info_sharp_lq084v1dg21,
.num_modes = 1,
- .lccr0 = LCCR0_PAS,
- .lccr3 = LCCR3_PCP,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
.pxafb_lcd_power = pcm990_lcd_power,
};
#elif defined(CONFIG_PCM990_DISPLAY_NEC)
static struct pxafb_mach_info pcm990_fbinfo __initdata = {
.modes = &fb_info_nec_nl6448bc20_18d,
.num_modes = 1,
- .lccr0 = LCCR0_Act,
- .lccr3 = LCCR3_PixFlEdg,
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
.pxafb_lcd_power = pcm990_lcd_power,
};
#endif
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/i2c.h>
#include <linux/smc91x.h>
+#include <linux/mfd/da903x.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/hardware.h>
#include <mach/pxa3xx-regs.h>
#include <mach/mfp-pxa930.h>
+#include <mach/i2c.h>
+#include <mach/regs-lcd.h>
+#include <mach/pxafb.h>
#include "devices.h"
#include "generic.h"
+#define GPIO_LCD_RESET (16)
+
/* SAAR MFP configurations */
static mfp_cfg_t saar_mfp_cfg[] __initdata = {
+ /* LCD */
+ GPIO23_LCD_DD0,
+ GPIO24_LCD_DD1,
+ GPIO25_LCD_DD2,
+ GPIO26_LCD_DD3,
+ GPIO27_LCD_DD4,
+ GPIO28_LCD_DD5,
+ GPIO29_LCD_DD6,
+ GPIO44_LCD_DD7,
+ GPIO21_LCD_CS,
+ GPIO22_LCD_VSYNC,
+ GPIO17_LCD_FCLK_RD,
+ GPIO18_LCD_LCLK_A0,
+ GPIO19_LCD_PCLK_WR,
+ GPIO16_GPIO, /* LCD reset */
+
/* Ethernet */
DF_nCS1_nCS3,
GPIO97_GPIO,
},
};
+#if defined(CONFIG_FB_PXA) || (CONFIG_FB_PXA_MODULE)
+static uint16_t lcd_power_on[] = {
+ /* single frame */
+ SMART_CMD_NOOP,
+ SMART_CMD(0x00),
+ SMART_DELAY(0),
+
+ SMART_CMD_NOOP,
+ SMART_CMD(0x00),
+ SMART_DELAY(0),
+
+ SMART_CMD_NOOP,
+ SMART_CMD(0x00),
+ SMART_DELAY(0),
+
+ SMART_CMD_NOOP,
+ SMART_CMD(0x00),
+ SMART_DELAY(10),
+
+ /* calibration control */
+ SMART_CMD(0x00),
+ SMART_CMD(0xA4),
+ SMART_DAT(0x80),
+ SMART_DAT(0x01),
+ SMART_DELAY(150),
+
+ /*Power-On Init sequence*/
+ SMART_CMD(0x00), /* output ctrl */
+ SMART_CMD(0x01),
+ SMART_DAT(0x01),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* wave ctrl */
+ SMART_CMD(0x02),
+ SMART_DAT(0x07),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x03), /* entry mode */
+ SMART_DAT(0xD0),
+ SMART_DAT(0x30),
+ SMART_CMD(0x00),
+ SMART_CMD(0x08), /* display ctrl 2 */
+ SMART_DAT(0x08),
+ SMART_DAT(0x08),
+ SMART_CMD(0x00),
+ SMART_CMD(0x09), /* display ctrl 3 */
+ SMART_DAT(0x04),
+ SMART_DAT(0x2F),
+ SMART_CMD(0x00),
+ SMART_CMD(0x0A), /* display ctrl 4 */
+ SMART_DAT(0x00),
+ SMART_DAT(0x08),
+ SMART_CMD(0x00),
+ SMART_CMD(0x0D), /* Frame Marker position */
+ SMART_DAT(0x00),
+ SMART_DAT(0x08),
+ SMART_CMD(0x00),
+ SMART_CMD(0x60), /* Driver output control */
+ SMART_DAT(0x27),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x61), /* Base image display control */
+ SMART_DAT(0x00),
+ SMART_DAT(0x01),
+ SMART_CMD(0x00),
+ SMART_CMD(0x30), /* Y settings 30h-3Dh */
+ SMART_DAT(0x07),
+ SMART_DAT(0x07),
+ SMART_CMD(0x00),
+ SMART_CMD(0x31),
+ SMART_DAT(0x00),
+ SMART_DAT(0x07),
+ SMART_CMD(0x00),
+ SMART_CMD(0x32), /* Timing(3), ASW HOLD=0.5CLK */
+ SMART_DAT(0x04),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x33), /* Timing(4), CKV ST=0CLK, CKV ED=1CLK */
+ SMART_DAT(0x03),
+ SMART_DAT(0x03),
+ SMART_CMD(0x00),
+ SMART_CMD(0x34),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x35),
+ SMART_DAT(0x02),
+ SMART_DAT(0x05),
+ SMART_CMD(0x00),
+ SMART_CMD(0x36),
+ SMART_DAT(0x1F),
+ SMART_DAT(0x1F),
+ SMART_CMD(0x00),
+ SMART_CMD(0x37),
+ SMART_DAT(0x07),
+ SMART_DAT(0x07),
+ SMART_CMD(0x00),
+ SMART_CMD(0x38),
+ SMART_DAT(0x00),
+ SMART_DAT(0x07),
+ SMART_CMD(0x00),
+ SMART_CMD(0x39),
+ SMART_DAT(0x04),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x3A),
+ SMART_DAT(0x03),
+ SMART_DAT(0x03),
+ SMART_CMD(0x00),
+ SMART_CMD(0x3B),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00),
+ SMART_CMD(0x3C),
+ SMART_DAT(0x02),
+ SMART_DAT(0x05),
+ SMART_CMD(0x00),
+ SMART_CMD(0x3D),
+ SMART_DAT(0x1F),
+ SMART_DAT(0x1F),
+ SMART_CMD(0x00), /* Display control 1 */
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x01),
+ SMART_CMD(0x00), /* Power control 5 */
+ SMART_CMD(0x17),
+ SMART_DAT(0x00),
+ SMART_DAT(0x01),
+ SMART_CMD(0x00), /* Power control 1 */
+ SMART_CMD(0x10),
+ SMART_DAT(0x10),
+ SMART_DAT(0xB0),
+ SMART_CMD(0x00), /* Power control 2 */
+ SMART_CMD(0x11),
+ SMART_DAT(0x01),
+ SMART_DAT(0x30),
+ SMART_CMD(0x00), /* Power control 3 */
+ SMART_CMD(0x12),
+ SMART_DAT(0x01),
+ SMART_DAT(0x9E),
+ SMART_CMD(0x00), /* Power control 4 */
+ SMART_CMD(0x13),
+ SMART_DAT(0x17),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* Power control 3 */
+ SMART_CMD(0x12),
+ SMART_DAT(0x01),
+ SMART_DAT(0xBE),
+ SMART_DELAY(100),
+
+ /* display mode : 240*320 */
+ SMART_CMD(0x00), /* RAM address set(H) 0*/
+ SMART_CMD(0x20),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* RAM address set(V) 4*/
+ SMART_CMD(0x21),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* Start of Window RAM address set(H) 8*/
+ SMART_CMD(0x50),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* End of Window RAM address set(H) 12*/
+ SMART_CMD(0x51),
+ SMART_DAT(0x00),
+ SMART_DAT(0xEF),
+ SMART_CMD(0x00), /* Start of Window RAM address set(V) 16*/
+ SMART_CMD(0x52),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* End of Window RAM address set(V) 20*/
+ SMART_CMD(0x53),
+ SMART_DAT(0x01),
+ SMART_DAT(0x3F),
+ SMART_CMD(0x00), /* Panel interface control 1 */
+ SMART_CMD(0x90),
+ SMART_DAT(0x00),
+ SMART_DAT(0x1A),
+ SMART_CMD(0x00), /* Panel interface control 2 */
+ SMART_CMD(0x92),
+ SMART_DAT(0x04),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* Panel interface control 3 */
+ SMART_CMD(0x93),
+ SMART_DAT(0x00),
+ SMART_DAT(0x05),
+ SMART_DELAY(20),
+};
+
+static uint16_t lcd_panel_on[] = {
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x21),
+ SMART_DELAY(1),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x61),
+ SMART_DELAY(100),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x01),
+ SMART_DAT(0x73),
+ SMART_DELAY(1),
+};
+
+static uint16_t lcd_panel_off[] = {
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x72),
+ SMART_DELAY(40),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x01),
+ SMART_DELAY(1),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x07),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_DELAY(1),
+};
+
+static uint16_t lcd_power_off[] = {
+ SMART_CMD(0x00),
+ SMART_CMD(0x10),
+ SMART_DAT(0x00),
+ SMART_DAT(0x80),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x11),
+ SMART_DAT(0x01),
+ SMART_DAT(0x60),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x12),
+ SMART_DAT(0x01),
+ SMART_DAT(0xAE),
+ SMART_DELAY(40),
+
+ SMART_CMD(0x00),
+ SMART_CMD(0x10),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+};
+
+static uint16_t update_framedata[] = {
+ /* set display ram: 240*320 */
+ SMART_CMD(0x00), /* RAM address set(H) 0*/
+ SMART_CMD(0x20),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* RAM address set(V) 4*/
+ SMART_CMD(0x21),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* Start of Window RAM address set(H) 8 */
+ SMART_CMD(0x50),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* End of Window RAM address set(H) 12 */
+ SMART_CMD(0x51),
+ SMART_DAT(0x00),
+ SMART_DAT(0xEF),
+ SMART_CMD(0x00), /* Start of Window RAM address set(V) 16 */
+ SMART_CMD(0x52),
+ SMART_DAT(0x00),
+ SMART_DAT(0x00),
+ SMART_CMD(0x00), /* End of Window RAM address set(V) 20 */
+ SMART_CMD(0x53),
+ SMART_DAT(0x01),
+ SMART_DAT(0x3F),
+
+ /* wait for vsync cmd before transferring frame data */
+ SMART_CMD_WAIT_FOR_VSYNC,
+
+ /* write ram */
+ SMART_CMD(0x00),
+ SMART_CMD(0x22),
+
+ /* write frame data */
+ SMART_CMD_WRITE_FRAME,
+};
+
+static void ltm022a97a_lcd_power(int on, struct fb_var_screeninfo *var)
+{
+ static int pin_requested = 0;
+ struct fb_info *info = container_of(var, struct fb_info, var);
+ int err;
+
+ if (!pin_requested) {
+ err = gpio_request(GPIO_LCD_RESET, "lcd reset");
+ if (err) {
+ pr_err("failed to request gpio for LCD reset\n");
+ return;
+ }
+
+ gpio_direction_output(GPIO_LCD_RESET, 0);
+ pin_requested = 1;
+ }
+
+ if (on) {
+ gpio_set_value(GPIO_LCD_RESET, 0); msleep(100);
+ gpio_set_value(GPIO_LCD_RESET, 1); msleep(10);
+
+ pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_on));
+ pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_on));
+ } else {
+ pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_off));
+ pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_off));
+ }
+
+ err = pxafb_smart_flush(info);
+ if (err)
+ pr_err("%s: timed out\n", __func__);
+}
+
+static void ltm022a97a_update(struct fb_info *info)
+{
+ pxafb_smart_queue(info, ARRAY_AND_SIZE(update_framedata));
+ pxafb_smart_flush(info);
+}
+
+static struct pxafb_mode_info toshiba_ltm022a97a_modes[] = {
+ [0] = {
+ .xres = 240,
+ .yres = 320,
+ .bpp = 16,
+ .a0csrd_set_hld = 30,
+ .a0cswr_set_hld = 30,
+ .wr_pulse_width = 30,
+ .rd_pulse_width = 30,
+ .op_hold_time = 30,
+ .cmd_inh_time = 60,
+
+ /* L_LCLK_A0 and L_LCLK_RD active low */
+ .sync = FB_SYNC_HOR_HIGH_ACT |
+ FB_SYNC_VERT_HIGH_ACT,
+ },
+};
+
+static struct pxafb_mach_info saar_lcd_info = {
+ .modes = toshiba_ltm022a97a_modes,
+ .num_modes = 1,
+ .lcd_conn = LCD_SMART_PANEL_8BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_lcd_power = ltm022a97a_lcd_power,
+ .smart_update = ltm022a97a_update,
+};
+
+static void __init saar_init_lcd(void)
+{
+ set_pxa_fb_info(&saar_lcd_info);
+}
+#else
+static inline void saar_init_lcd(void) {}
+#endif
+
+#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
+static struct da903x_subdev_info saar_da9034_subdevs[] = {
+ [0] = {
+ .name = "da903x-backlight",
+ .id = DA9034_ID_WLED,
+ },
+};
+
+static struct da903x_platform_data saar_da9034_info = {
+ .num_subdevs = ARRAY_SIZE(saar_da9034_subdevs),
+ .subdevs = saar_da9034_subdevs,
+};
+
+static struct i2c_board_info saar_i2c_info[] = {
+ [0] = {
+ .type = "da9034",
+ .addr = 0x34,
+ .platform_data = &saar_da9034_info,
+ .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO83)),
+ },
+};
+
+static void __init saar_init_i2c(void)
+{
+ pxa_set_i2c_info(NULL);
+ i2c_register_board_info(0, ARRAY_AND_SIZE(saar_i2c_info));
+}
+#else
+static inline void saar_init_i2c(void) {}
+#endif
static void __init saar_init(void)
{
/* initialize MFP configurations */
pxa3xx_mfp_config(ARRAY_AND_SIZE(saar_mfp_cfg));
platform_device_register(&smc91x_device);
+
+ saar_init_i2c();
+ saar_init_lcd();
}
MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)")
#include <asm/irq.h>
#include <asm/div64.h>
#include <mach/pxa-regs.h>
-#include <mach/pxa2xx-gpio.h>
#include <mach/bitfield.h>
#include <mach/pxafb.h>
int i;
struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
- /* leave 2 commands for INTERRUPT and WAIT_FOR_SYNC */
- for (i = 0; i < n_cmds; i++) {
+ for (i = 0; i < n_cmds; i++, cmds++) {
+ /* if it is a software delay, flush and delay */
+ if ((*cmds & 0xff00) == SMART_CMD_DELAY) {
+ pxafb_smart_flush(info);
+ mdelay(*cmds & 0xff);
+ continue;
+ }
+
+ /* leave 2 commands for INTERRUPT and WAIT_FOR_SYNC */
if (fbi->n_smart_cmds == CMD_BUFF_SIZE - 8)
pxafb_smart_flush(info);
- fbi->smart_cmds[fbi->n_smart_cmds++] = *cmds++;
+ fbi->smart_cmds[fbi->n_smart_cmds++] = *cmds;
}
return 0;
LCCR1_HorSnchWdth(__smart_timing(t3, lclk));
fbi->reg_lccr2 = LCCR2_DisHght(var->yres);
- fbi->reg_lccr3 = LCCR3_PixClkDiv(__smart_timing(t4, lclk));
+ fbi->reg_lccr3 = fbi->lccr3 | LCCR3_PixClkDiv(__smart_timing(t4, lclk));
+ fbi->reg_lccr3 |= (var->sync & FB_SYNC_HOR_HIGH_ACT) ? LCCR3_HSP : 0;
+ fbi->reg_lccr3 |= (var->sync & FB_SYNC_VERT_HIGH_ACT) ? LCCR3_VSP : 0;
/* FIXME: make this configurable */
fbi->reg_cmdcr = 1;
if (try_to_freeze())
continue;
+ mutex_lock(&fbi->ctrlr_lock);
+
if (fbi->state == C_ENABLE) {
inf->smart_update(&fbi->fb);
complete(&fbi->refresh_done);
}
+ mutex_unlock(&fbi->ctrlr_lock);
+
set_current_state(TASK_INTERRUPTIBLE);
schedule_timeout(30 * HZ / 1000);
}
static int pxafb_smart_init(struct pxafb_info *fbi)
{
- if (!(fbi->lccr0 | LCCR0_LCDT))
+ if (!(fbi->lccr0 & LCCR0_LCDT))
return 0;
+ fbi->smart_cmds = (uint16_t *) fbi->dma_buff->cmd_buff;
+ fbi->n_smart_cmds = 0;
+
+ init_completion(&fbi->command_done);
+ init_completion(&fbi->refresh_done);
+
fbi->smart_thread = kthread_run(pxafb_smart_thread, fbi,
"lcd_refresh");
if (IS_ERR(fbi->smart_thread)) {
- printk(KERN_ERR "%s: unable to create kernel thread\n",
- __func__);
+ pr_err("%s: unable to create kernel thread\n", __func__);
return PTR_ERR(fbi->smart_thread);
}
{
return 0;
}
-#endif /* CONFIG_FB_SMART_PANEL */
+
+static inline int pxafb_smart_init(struct pxafb_info *fbi) { return 0; }
+#endif /* CONFIG_FB_PXA_SMARTPANEL */
static void setup_parallel_timing(struct pxafb_info *fbi,
struct fb_var_screeninfo *var)
fbi->lcd_power(on, &fbi->fb.var);
}
-static void pxafb_setup_gpio(struct pxafb_info *fbi)
-{
- int gpio, ldd_bits;
- unsigned int lccr0 = fbi->lccr0;
-
- /*
- * setup is based on type of panel supported
- */
-
- /* 4 bit interface */
- if ((lccr0 & LCCR0_CMS) == LCCR0_Mono &&
- (lccr0 & LCCR0_SDS) == LCCR0_Sngl &&
- (lccr0 & LCCR0_DPD) == LCCR0_4PixMono)
- ldd_bits = 4;
-
- /* 8 bit interface */
- else if (((lccr0 & LCCR0_CMS) == LCCR0_Mono &&
- ((lccr0 & LCCR0_SDS) == LCCR0_Dual ||
- (lccr0 & LCCR0_DPD) == LCCR0_8PixMono)) ||
- ((lccr0 & LCCR0_CMS) == LCCR0_Color &&
- (lccr0 & LCCR0_PAS) == LCCR0_Pas &&
- (lccr0 & LCCR0_SDS) == LCCR0_Sngl))
- ldd_bits = 8;
-
- /* 16 bit interface */
- else if ((lccr0 & LCCR0_CMS) == LCCR0_Color &&
- ((lccr0 & LCCR0_SDS) == LCCR0_Dual ||
- (lccr0 & LCCR0_PAS) == LCCR0_Act))
- ldd_bits = 16;
-
- else {
- printk(KERN_ERR "pxafb_setup_gpio: unable to determine "
- "bits per pixel\n");
- return;
- }
-
- for (gpio = 58; ldd_bits; gpio++, ldd_bits--)
- pxa_gpio_mode(gpio | GPIO_ALT_FN_2_OUT);
- /* 18 bit interface */
- if (fbi->fb.var.bits_per_pixel > 16) {
- pxa_gpio_mode(86 | GPIO_ALT_FN_2_OUT);
- pxa_gpio_mode(87 | GPIO_ALT_FN_2_OUT);
- }
- pxa_gpio_mode(GPIO74_LCD_FCLK_MD);
- pxa_gpio_mode(GPIO75_LCD_LCLK_MD);
- pxa_gpio_mode(GPIO76_LCD_PCLK_MD);
-
- if ((lccr0 & LCCR0_PAS) == 0)
- pxa_gpio_mode(GPIO77_LCD_ACBIAS_MD);
-}
-
static void pxafb_enable_controller(struct pxafb_info *fbi)
{
pr_debug("pxafb: Enabling LCD controller\n");
if (old_state == C_ENABLE) {
__pxafb_lcd_power(fbi, 0);
pxafb_disable_controller(fbi);
- pxafb_setup_gpio(fbi);
pxafb_enable_controller(fbi);
__pxafb_lcd_power(fbi, 1);
}
*/
if (old_state != C_ENABLE) {
fbi->state = C_ENABLE;
- pxafb_setup_gpio(fbi);
pxafb_enable_controller(fbi);
__pxafb_lcd_power(fbi, 1);
__pxafb_backlight_power(fbi, 1);
fbi->palette_cpu = (u16 *) fbi->dma_buff->palette;
pr_debug("pxafb: palette_mem_size = 0x%08x\n", fbi->palette_size*sizeof(u16));
-
-#ifdef CONFIG_FB_PXA_SMARTPANEL
- fbi->smart_cmds = (uint16_t *) fbi->dma_buff->cmd_buff;
- fbi->n_smart_cmds = 0;
-#endif
}
return fbi->map_cpu ? 0 : -ENOMEM;
INIT_WORK(&fbi->task, pxafb_task);
mutex_init(&fbi->ctrlr_lock);
init_completion(&fbi->disable_done);
-#ifdef CONFIG_FB_PXA_SMARTPANEL
- init_completion(&fbi->command_done);
- init_completion(&fbi->refresh_done);
-#endif
return fbi;
}
goto failed_free_mem;
}
-#ifdef CONFIG_FB_PXA_SMARTPANEL
ret = pxafb_smart_init(fbi);
if (ret) {
dev_err(&dev->dev, "failed to initialize smartpanel\n");
goto failed_free_irq;
}
-#endif
+
/*
* This makes sure that our colour bitfield
* descriptors are correctly initialised.
projects / linux-2.6-omap-h63xx.git / commitdiff