+++ /dev/null
-/*
- * Driver for 8250/16550-type serial ports
- *
- * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
- *
- * Copyright (C) 2001 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * A note about mapbase / membase
- *
- * mapbase is the physical address of the IO port. Currently, we don't
- * support this very well, and it may well be dropped from this driver
- * in future. As such, mapbase should be NULL.
- *
- * membase is an 'ioremapped' cookie. This is compatible with the old
- * serial.c driver, and is currently the preferred form.
- */
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/tty.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/console.h>
-#include <linux/sysrq.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <linux/delay.h>
-
-#include <asm/serial.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#if defined(CONFIG_SERIAL_AU1X00_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
-#include <linux/serial_core.h>
-#include "8250.h"
-
-/*
- * Debugging.
- */
-#if 0
-#define DEBUG_AUTOCONF(fmt...) printk(fmt)
-#else
-#define DEBUG_AUTOCONF(fmt...) do { } while (0)
-#endif
-
-#if 0
-#define DEBUG_INTR(fmt...) printk(fmt)
-#else
-#define DEBUG_INTR(fmt...) do { } while (0)
-#endif
-
-#define PASS_LIMIT 256
-
-/*
- * We default to IRQ0 for the "no irq" hack. Some
- * machine types want others as well - they're free
- * to redefine this in their header file.
- */
-#define is_real_interrupt(irq) ((irq) != 0)
-
-static struct old_serial_port old_serial_port[] = {
- { .baud_base = 0,
- .iomem_base = (u8 *)UART0_ADDR,
- .irq = AU1000_UART0_INT,
- .flags = STD_COM_FLAGS,
- .iomem_reg_shift = 2,
- }, {
- .baud_base = 0,
- .iomem_base = (u8 *)UART1_ADDR,
- .irq = AU1000_UART1_INT,
- .flags = STD_COM_FLAGS,
- .iomem_reg_shift = 2
- }, {
- .baud_base = 0,
- .iomem_base = (u8 *)UART2_ADDR,
- .irq = AU1000_UART2_INT,
- .flags = STD_COM_FLAGS,
- .iomem_reg_shift = 2
- }, {
- .baud_base = 0,
- .iomem_base = (u8 *)UART3_ADDR,
- .irq = AU1000_UART3_INT,
- .flags = STD_COM_FLAGS,
- .iomem_reg_shift = 2
- }
-};
-
-#define UART_NR ARRAY_SIZE(old_serial_port)
-
-struct uart_8250_port {
- struct uart_port port;
- struct timer_list timer; /* "no irq" timer */
- struct list_head list; /* ports on this IRQ */
- unsigned short rev;
- unsigned char acr;
- unsigned char ier;
- unsigned char lcr;
- unsigned char mcr_mask; /* mask of user bits */
- unsigned char mcr_force; /* mask of forced bits */
- unsigned char lsr_break_flag;
-
- /*
- * We provide a per-port pm hook.
- */
- void (*pm)(struct uart_port *port,
- unsigned int state, unsigned int old);
-};
-
-struct irq_info {
- spinlock_t lock;
- struct list_head *head;
-};
-
-static struct irq_info irq_lists[NR_IRQS];
-
-/*
- * Here we define the default xmit fifo size used for each type of UART.
- */
-static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
- { "unknown", 1, 0 },
- { "8250", 1, 0 },
- { "16450", 1, 0 },
- { "16550", 1, 0 },
- /* PORT_16550A */
- { "AU1X00_UART",16, UART_CLEAR_FIFO | UART_USE_FIFO },
-};
-
-static unsigned int serial_in(struct uart_8250_port *up, int offset)
-{
- return au_readl((unsigned long)up->port.membase + offset);
-}
-
-static void serial_out(struct uart_8250_port *up, int offset, int value)
-{
- au_writel(value, (unsigned long)up->port.membase + offset);
-}
-
-#define serial_inp(up, offset) serial_in(up, offset)
-#define serial_outp(up, offset, value) serial_out(up, offset, value)
-
-/*
- * This routine is called by rs_init() to initialize a specific serial
- * port. It determines what type of UART chip this serial port is
- * using: 8250, 16450, 16550, 16550A. The important question is
- * whether or not this UART is a 16550A or not, since this will
- * determine whether or not we can use its FIFO features or not.
- */
-static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
-{
- unsigned char save_lcr, save_mcr;
- unsigned long flags;
-
- if (!up->port.iobase && !up->port.mapbase && !up->port.membase)
- return;
-
- DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04x, 0x%08lx): ",
- up->port.line, up->port.iobase, up->port.membase);
-
- /*
- * We really do need global IRQs disabled here - we're going to
- * be frobbing the chips IRQ enable register to see if it exists.
- */
- spin_lock_irqsave(&up->port.lock, flags);
-// save_flags(flags); cli();
-
- save_mcr = serial_in(up, UART_MCR);
- save_lcr = serial_in(up, UART_LCR);
-
- up->port.type = PORT_16550A;
- serial_outp(up, UART_LCR, save_lcr);
-
- up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
-
- if (up->port.type == PORT_UNKNOWN)
- goto out;
-
- /*
- * Reset the UART.
- */
- serial_outp(up, UART_MCR, save_mcr);
- serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
- UART_FCR_CLEAR_RCVR |
- UART_FCR_CLEAR_XMIT));
- serial_outp(up, UART_FCR, 0);
- (void)serial_in(up, UART_RX);
- serial_outp(up, UART_IER, 0);
-
- out:
- spin_unlock_irqrestore(&up->port.lock, flags);
-// restore_flags(flags);
- DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
-}
-
-static void serial8250_stop_tx(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
- if (up->ier & UART_IER_THRI) {
- up->ier &= ~UART_IER_THRI;
- serial_out(up, UART_IER, up->ier);
- }
-}
-
-static void serial8250_start_tx(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
- if (!(up->ier & UART_IER_THRI)) {
- up->ier |= UART_IER_THRI;
- serial_out(up, UART_IER, up->ier);
- }
-}
-
-static void serial8250_stop_rx(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
- up->ier &= ~UART_IER_RLSI;
- up->port.read_status_mask &= ~UART_LSR_DR;
- serial_out(up, UART_IER, up->ier);
-}
-
-static void serial8250_enable_ms(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
- up->ier |= UART_IER_MSI;
- serial_out(up, UART_IER, up->ier);
-}
-
-static void
-receive_chars(struct uart_8250_port *up, int *status, struct pt_regs *regs)
-{
- struct tty_struct *tty = up->port.info->tty;
- unsigned char ch, flag;
- int max_count = 256;
-
- do {
- ch = serial_inp(up, UART_RX);
- flag = TTY_NORMAL;
- up->port.icount.rx++;
-
- if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
- UART_LSR_FE | UART_LSR_OE))) {
- /*
- * For statistics only
- */
- if (*status & UART_LSR_BI) {
- *status &= ~(UART_LSR_FE | UART_LSR_PE);
- up->port.icount.brk++;
- /*
- * We do the SysRQ and SAK checking
- * here because otherwise the break
- * may get masked by ignore_status_mask
- * or read_status_mask.
- */
- if (uart_handle_break(&up->port))
- goto ignore_char;
- } else if (*status & UART_LSR_PE)
- up->port.icount.parity++;
- else if (*status & UART_LSR_FE)
- up->port.icount.frame++;
- if (*status & UART_LSR_OE)
- up->port.icount.overrun++;
-
- /*
- * Mask off conditions which should be ingored.
- */
- *status &= up->port.read_status_mask;
-
-#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
- if (up->port.line == up->port.cons->index) {
- /* Recover the break flag from console xmit */
- *status |= up->lsr_break_flag;
- up->lsr_break_flag = 0;
- }
-#endif
- if (*status & UART_LSR_BI) {
- DEBUG_INTR("handling break....");
- flag = TTY_BREAK;
- } else if (*status & UART_LSR_PE)
- flag = TTY_PARITY;
- else if (*status & UART_LSR_FE)
- flag = TTY_FRAME;
- }
- if (uart_handle_sysrq_char(&up->port, ch, regs))
- goto ignore_char;
- if ((*status & up->port.ignore_status_mask) == 0)
- tty_insert_flip_char(tty, ch, flag);
- if (*status & UART_LSR_OE)
- /*
- * Overrun is special, since it's reported
- * immediately, and doesn't affect the current
- * character.
- */
- tty_insert_flip_char(tty, 0, TTY_OVERRUN);
- }
- ignore_char:
- *status = serial_inp(up, UART_LSR);
- } while ((*status & UART_LSR_DR) && (max_count-- > 0));
- spin_unlock(&up->port.lock);
- tty_flip_buffer_push(tty);
- spin_lock(&up->port.lock);
-}
-
-static void transmit_chars(struct uart_8250_port *up)
-{
- struct circ_buf *xmit = &up->port.info->xmit;
- int count;
-
- if (up->port.x_char) {
- serial_outp(up, UART_TX, up->port.x_char);
- up->port.icount.tx++;
- up->port.x_char = 0;
- return;
- }
- if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
- serial8250_stop_tx(&up->port);
- return;
- }
-
- count = up->port.fifosize;
- do {
- serial_out(up, UART_TX, xmit->buf[xmit->tail]);
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- up->port.icount.tx++;
- if (uart_circ_empty(xmit))
- break;
- } while (--count > 0);
-
- if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
- uart_write_wakeup(&up->port);
-
- DEBUG_INTR("THRE...");
-
- if (uart_circ_empty(xmit))
- serial8250_stop_tx(&up->port);
-}
-
-static void check_modem_status(struct uart_8250_port *up)
-{
- int status;
-
- status = serial_in(up, UART_MSR);
-
- if ((status & UART_MSR_ANY_DELTA) == 0)
- return;
-
- if (status & UART_MSR_TERI)
- up->port.icount.rng++;
- if (status & UART_MSR_DDSR)
- up->port.icount.dsr++;
- if (status & UART_MSR_DDCD)
- uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
- if (status & UART_MSR_DCTS)
- uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
-
- wake_up_interruptible(&up->port.info->delta_msr_wait);
-}
-
-/*
- * This handles the interrupt from one port.
- */
-static inline void
-serial8250_handle_port(struct uart_8250_port *up, struct pt_regs *regs)
-{
- unsigned int status = serial_inp(up, UART_LSR);
-
- DEBUG_INTR("status = %x...", status);
-
- if (status & UART_LSR_DR)
- receive_chars(up, &status, regs);
- check_modem_status(up);
- if (status & UART_LSR_THRE)
- transmit_chars(up);
-}
-
-/*
- * This is the serial driver's interrupt routine.
- *
- * Arjan thinks the old way was overly complex, so it got simplified.
- * Alan disagrees, saying that need the complexity to handle the weird
- * nature of ISA shared interrupts. (This is a special exception.)
- *
- * In order to handle ISA shared interrupts properly, we need to check
- * that all ports have been serviced, and therefore the ISA interrupt
- * line has been de-asserted.
- *
- * This means we need to loop through all ports. checking that they
- * don't have an interrupt pending.
- */
-static irqreturn_t serial8250_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- struct irq_info *i = dev_id;
- struct list_head *l, *end = NULL;
- int pass_counter = 0;
-
- DEBUG_INTR("serial8250_interrupt(%d)...", irq);
-
- spin_lock(&i->lock);
-
- l = i->head;
- do {
- struct uart_8250_port *up;
- unsigned int iir;
-
- up = list_entry(l, struct uart_8250_port, list);
-
- iir = serial_in(up, UART_IIR);
- if (!(iir & UART_IIR_NO_INT)) {
- spin_lock(&up->port.lock);
- serial8250_handle_port(up, regs);
- spin_unlock(&up->port.lock);
-
- end = NULL;
- } else if (end == NULL)
- end = l;
-
- l = l->next;
-
- if (l == i->head && pass_counter++ > PASS_LIMIT) {
- /* If we hit this, we're dead. */
- printk(KERN_ERR "serial8250: too much work for "
- "irq%d\n", irq);
- break;
- }
- } while (l != end);
-
- spin_unlock(&i->lock);
-
- DEBUG_INTR("end.\n");
- /* FIXME! Was it really ours? */
- return IRQ_HANDLED;
-}
-
-/*
- * To support ISA shared interrupts, we need to have one interrupt
- * handler that ensures that the IRQ line has been deasserted
- * before returning. Failing to do this will result in the IRQ
- * line being stuck active, and, since ISA irqs are edge triggered,
- * no more IRQs will be seen.
- */
-static void serial_do_unlink(struct irq_info *i, struct uart_8250_port *up)
-{
- spin_lock_irq(&i->lock);
-
- if (!list_empty(i->head)) {
- if (i->head == &up->list)
- i->head = i->head->next;
- list_del(&up->list);
- } else {
- BUG_ON(i->head != &up->list);
- i->head = NULL;
- }
-
- spin_unlock_irq(&i->lock);
-}
-
-static int serial_link_irq_chain(struct uart_8250_port *up)
-{
- struct irq_info *i = irq_lists + up->port.irq;
- int ret, irq_flags = up->port.flags & UPF_SHARE_IRQ ? SA_SHIRQ : 0;
-
- spin_lock_irq(&i->lock);
-
- if (i->head) {
- list_add(&up->list, i->head);
- spin_unlock_irq(&i->lock);
-
- ret = 0;
- } else {
- INIT_LIST_HEAD(&up->list);
- i->head = &up->list;
- spin_unlock_irq(&i->lock);
-
- ret = request_irq(up->port.irq, serial8250_interrupt,
- irq_flags, "serial", i);
- if (ret < 0)
- serial_do_unlink(i, up);
- }
-
- return ret;
-}
-
-static void serial_unlink_irq_chain(struct uart_8250_port *up)
-{
- struct irq_info *i = irq_lists + up->port.irq;
-
- BUG_ON(i->head == NULL);
-
- if (list_empty(i->head))
- free_irq(up->port.irq, i);
-
- serial_do_unlink(i, up);
-}
-
-/*
- * This function is used to handle ports that do not have an
- * interrupt. This doesn't work very well for 16450's, but gives
- * barely passable results for a 16550A. (Although at the expense
- * of much CPU overhead).
- */
-static void serial8250_timeout(unsigned long data)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)data;
- unsigned int timeout;
- unsigned int iir;
-
- iir = serial_in(up, UART_IIR);
- if (!(iir & UART_IIR_NO_INT)) {
- spin_lock(&up->port.lock);
- serial8250_handle_port(up, NULL);
- spin_unlock(&up->port.lock);
- }
-
- timeout = up->port.timeout;
- timeout = timeout > 6 ? (timeout / 2 - 2) : 1;
- mod_timer(&up->timer, jiffies + timeout);
-}
-
-static unsigned int serial8250_tx_empty(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long flags;
- unsigned int ret;
-
- spin_lock_irqsave(&up->port.lock, flags);
- ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
- spin_unlock_irqrestore(&up->port.lock, flags);
-
- return ret;
-}
-
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned char status;
- unsigned int ret;
-
- status = serial_in(up, UART_MSR);
-
- ret = 0;
- if (status & UART_MSR_DCD)
- ret |= TIOCM_CAR;
- if (status & UART_MSR_RI)
- ret |= TIOCM_RNG;
- if (status & UART_MSR_DSR)
- ret |= TIOCM_DSR;
- if (status & UART_MSR_CTS)
- ret |= TIOCM_CTS;
- return ret;
-}
-
-static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned char mcr = 0;
-
- if (mctrl & TIOCM_RTS)
- mcr |= UART_MCR_RTS;
- if (mctrl & TIOCM_DTR)
- mcr |= UART_MCR_DTR;
- if (mctrl & TIOCM_OUT1)
- mcr |= UART_MCR_OUT1;
- if (mctrl & TIOCM_OUT2)
- mcr |= UART_MCR_OUT2;
- if (mctrl & TIOCM_LOOP)
- mcr |= UART_MCR_LOOP;
-
- mcr = (mcr & up->mcr_mask) | up->mcr_force;
-
- serial_out(up, UART_MCR, mcr);
-}
-
-static void serial8250_break_ctl(struct uart_port *port, int break_state)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long flags;
-
- spin_lock_irqsave(&up->port.lock, flags);
- if (break_state == -1)
- up->lcr |= UART_LCR_SBC;
- else
- up->lcr &= ~UART_LCR_SBC;
- serial_out(up, UART_LCR, up->lcr);
- spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static int serial8250_startup(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long flags;
- int retval;
-
- /*
- * Clear the FIFO buffers and disable them.
- * (they will be reeanbled in set_termios())
- */
- if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
- UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_outp(up, UART_FCR, 0);
- }
-
- /*
- * Clear the interrupt registers.
- */
- (void) serial_inp(up, UART_LSR);
- (void) serial_inp(up, UART_RX);
- (void) serial_inp(up, UART_IIR);
- (void) serial_inp(up, UART_MSR);
-
- /*
- * At this point, there's no way the LSR could still be 0xff;
- * if it is, then bail out, because there's likely no UART
- * here.
- */
- if (!(up->port.flags & UPF_BUGGY_UART) &&
- (serial_inp(up, UART_LSR) == 0xff)) {
- printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
- return -ENODEV;
- }
-
- retval = serial_link_irq_chain(up);
- if (retval)
- return retval;
-
- /*
- * Now, initialize the UART
- */
- serial_outp(up, UART_LCR, UART_LCR_WLEN8);
-
- spin_lock_irqsave(&up->port.lock, flags);
- if (up->port.flags & UPF_FOURPORT) {
- if (!is_real_interrupt(up->port.irq))
- up->port.mctrl |= TIOCM_OUT1;
- } else
- /*
- * Most PC uarts need OUT2 raised to enable interrupts.
- */
- if (is_real_interrupt(up->port.irq))
- up->port.mctrl |= TIOCM_OUT2;
-
- serial8250_set_mctrl(&up->port, up->port.mctrl);
- spin_unlock_irqrestore(&up->port.lock, flags);
-
- /*
- * Finally, enable interrupts. Note: Modem status interrupts
- * are set via set_termios(), which will be occurring imminently
- * anyway, so we don't enable them here.
- */
- up->ier = UART_IER_RLSI | UART_IER_RDI;
- serial_outp(up, UART_IER, up->ier);
-
- if (up->port.flags & UPF_FOURPORT) {
- unsigned int icp;
- /*
- * Enable interrupts on the AST Fourport board
- */
- icp = (up->port.iobase & 0xfe0) | 0x01f;
- outb_p(0x80, icp);
- (void) inb_p(icp);
- }
-
- /*
- * And clear the interrupt registers again for luck.
- */
- (void) serial_inp(up, UART_LSR);
- (void) serial_inp(up, UART_RX);
- (void) serial_inp(up, UART_IIR);
- (void) serial_inp(up, UART_MSR);
-
- return 0;
-}
-
-static void serial8250_shutdown(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long flags;
-
- /*
- * Disable interrupts from this port
- */
- up->ier = 0;
- serial_outp(up, UART_IER, 0);
-
- spin_lock_irqsave(&up->port.lock, flags);
- if (up->port.flags & UPF_FOURPORT) {
- /* reset interrupts on the AST Fourport board */
- inb((up->port.iobase & 0xfe0) | 0x1f);
- up->port.mctrl |= TIOCM_OUT1;
- } else
- up->port.mctrl &= ~TIOCM_OUT2;
-
- serial8250_set_mctrl(&up->port, up->port.mctrl);
- spin_unlock_irqrestore(&up->port.lock, flags);
-
- /*
- * Disable break condition and FIFOs
- */
- serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
- UART_FCR_CLEAR_RCVR |
- UART_FCR_CLEAR_XMIT);
- serial_outp(up, UART_FCR, 0);
-
- /*
- * Read data port to reset things, and then unlink from
- * the IRQ chain.
- */
- (void) serial_in(up, UART_RX);
-
- if (!is_real_interrupt(up->port.irq))
- del_timer_sync(&up->timer);
- else
- serial_unlink_irq_chain(up);
-}
-
-static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int baud)
-{
- unsigned int quot;
-
- /*
- * Handle magic divisors for baud rates above baud_base on
- * SMSC SuperIO chips.
- */
- if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
- baud == (port->uartclk/4))
- quot = 0x8001;
- else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
- baud == (port->uartclk/8))
- quot = 0x8002;
- else
- quot = uart_get_divisor(port, baud);
-
- return quot;
-}
-
-static void
-serial8250_set_termios(struct uart_port *port, struct termios *termios,
- struct termios *old)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned char cval, fcr = 0;
- unsigned long flags;
- unsigned int baud, quot;
-
- switch (termios->c_cflag & CSIZE) {
- case CS5:
- cval = UART_LCR_WLEN5;
- break;
- case CS6:
- cval = UART_LCR_WLEN6;
- break;
- case CS7:
- cval = UART_LCR_WLEN7;
- break;
- default:
- case CS8:
- cval = UART_LCR_WLEN8;
- break;
- }
-
- if (termios->c_cflag & CSTOPB)
- cval |= UART_LCR_STOP;
- if (termios->c_cflag & PARENB)
- cval |= UART_LCR_PARITY;
- if (!(termios->c_cflag & PARODD))
- cval |= UART_LCR_EPAR;
-#ifdef CMSPAR
- if (termios->c_cflag & CMSPAR)
- cval |= UART_LCR_SPAR;
-#endif
-
- /*
- * Ask the core to calculate the divisor for us.
- */
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = serial8250_get_divisor(port, baud);
- quot = 0x35; /* FIXME */
-
- /*
- * Work around a bug in the Oxford Semiconductor 952 rev B
- * chip which causes it to seriously miscalculate baud rates
- * when DLL is 0.
- */
- if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
- up->rev == 0x5201)
- quot ++;
-
- if (uart_config[up->port.type].flags & UART_USE_FIFO) {
- if (baud < 2400)
- fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_1;
- else
- fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIGGER_8;
- }
-
- /*
- * Ok, we're now changing the port state. Do it with
- * interrupts disabled.
- */
- spin_lock_irqsave(&up->port.lock, flags);
-
- /*
- * Update the per-port timeout.
- */
- uart_update_timeout(port, termios->c_cflag, baud);
-
- up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
- if (termios->c_iflag & INPCK)
- up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
- if (termios->c_iflag & (BRKINT | PARMRK))
- up->port.read_status_mask |= UART_LSR_BI;
-
- /*
- * Characteres to ignore
- */
- up->port.ignore_status_mask = 0;
- if (termios->c_iflag & IGNPAR)
- up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
- if (termios->c_iflag & IGNBRK) {
- up->port.ignore_status_mask |= UART_LSR_BI;
- /*
- * If we're ignoring parity and break indicators,
- * ignore overruns too (for real raw support).
- */
- if (termios->c_iflag & IGNPAR)
- up->port.ignore_status_mask |= UART_LSR_OE;
- }
-
- /*
- * ignore all characters if CREAD is not set
- */
- if ((termios->c_cflag & CREAD) == 0)
- up->port.ignore_status_mask |= UART_LSR_DR;
-
- /*
- * CTS flow control flag and modem status interrupts
- */
- up->ier &= ~UART_IER_MSI;
- if (UART_ENABLE_MS(&up->port, termios->c_cflag))
- up->ier |= UART_IER_MSI;
-
- serial_out(up, UART_IER, up->ier);
- serial_outp(up, 0x28, quot & 0xffff);
- up->lcr = cval; /* Save LCR */
- if (up->port.type != PORT_16750) {
- if (fcr & UART_FCR_ENABLE_FIFO) {
- /* emulated UARTs (Lucent Venus 167x) need two steps */
- serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- }
- serial_outp(up, UART_FCR, fcr); /* set fcr */
- }
- spin_unlock_irqrestore(&up->port.lock, flags);
-}
-
-static void
-serial8250_pm(struct uart_port *port, unsigned int state,
- unsigned int oldstate)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- if (state) {
- /* sleep */
- if (up->pm)
- up->pm(port, state, oldstate);
- } else {
- /* wake */
- if (up->pm)
- up->pm(port, state, oldstate);
- }
-}
-
-/*
- * Resource handling. This is complicated by the fact that resources
- * depend on the port type. Maybe we should be claiming the standard
- * 8250 ports, and then trying to get other resources as necessary?
- */
-static int
-serial8250_request_std_resource(struct uart_8250_port *up, struct resource **res)
-{
- unsigned int size = 8 << up->port.regshift;
- int ret = 0;
-
- switch (up->port.iotype) {
- case UPIO_MEM:
- if (up->port.mapbase) {
- *res = request_mem_region(up->port.mapbase, size, "serial");
- if (!*res)
- ret = -EBUSY;
- }
- break;
-
- case UPIO_HUB6:
- case UPIO_PORT:
- *res = request_region(up->port.iobase, size, "serial");
- if (!*res)
- ret = -EBUSY;
- break;
- }
- return ret;
-}
-
-
-static void serial8250_release_port(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- unsigned long start, offset = 0, size = 0;
-
- size <<= up->port.regshift;
-
- switch (up->port.iotype) {
- case UPIO_MEM:
- if (up->port.mapbase) {
- /*
- * Unmap the area.
- */
- iounmap(up->port.membase);
- up->port.membase = NULL;
-
- start = up->port.mapbase;
-
- if (size)
- release_mem_region(start + offset, size);
- release_mem_region(start, 8 << up->port.regshift);
- }
- break;
-
- case UPIO_HUB6:
- case UPIO_PORT:
- start = up->port.iobase;
-
- if (size)
- release_region(start + offset, size);
- release_region(start + offset, 8 << up->port.regshift);
- break;
-
- default:
- break;
- }
-}
-
-static int serial8250_request_port(struct uart_port *port)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- struct resource *res = NULL, *res_rsa = NULL;
- int ret = 0;
-
- ret = serial8250_request_std_resource(up, &res);
-
- /*
- * If we have a mapbase, then request that as well.
- */
- if (ret == 0 && up->port.flags & UPF_IOREMAP) {
- int size = res->end - res->start + 1;
-
- up->port.membase = ioremap(up->port.mapbase, size);
- if (!up->port.membase)
- ret = -ENOMEM;
- }
-
- if (ret < 0) {
- if (res_rsa)
- release_resource(res_rsa);
- if (res)
- release_resource(res);
- }
- return ret;
-}
-
-static void serial8250_config_port(struct uart_port *port, int flags)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
- struct resource *res_std = NULL, *res_rsa = NULL;
- int probeflags = PROBE_ANY;
-
- probeflags &= ~PROBE_RSA;
-
- if (flags & UART_CONFIG_TYPE)
- autoconfig(up, probeflags);
-
- /*
- * If the port wasn't an RSA port, release the resource.
- */
- if (up->port.type != PORT_RSA && res_rsa)
- release_resource(res_rsa);
-
- if (up->port.type == PORT_UNKNOWN && res_std)
- release_resource(res_std);
-}
-
-static int
-serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
- if (ser->irq >= NR_IRQS || ser->irq < 0 ||
- ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
- ser->type > PORT_MAX_8250 || ser->type == PORT_CIRRUS ||
- ser->type == PORT_STARTECH)
- return -EINVAL;
- return 0;
-}
-
-static const char *
-serial8250_type(struct uart_port *port)
-{
- int type = port->type;
-
- if (type >= ARRAY_SIZE(uart_config))
- type = 0;
- return uart_config[type].name;
-}
-
-static struct uart_ops serial8250_pops = {
- .tx_empty = serial8250_tx_empty,
- .set_mctrl = serial8250_set_mctrl,
- .get_mctrl = serial8250_get_mctrl,
- .stop_tx = serial8250_stop_tx,
- .start_tx = serial8250_start_tx,
- .stop_rx = serial8250_stop_rx,
- .enable_ms = serial8250_enable_ms,
- .break_ctl = serial8250_break_ctl,
- .startup = serial8250_startup,
- .shutdown = serial8250_shutdown,
- .set_termios = serial8250_set_termios,
- .pm = serial8250_pm,
- .type = serial8250_type,
- .release_port = serial8250_release_port,
- .request_port = serial8250_request_port,
- .config_port = serial8250_config_port,
- .verify_port = serial8250_verify_port,
-};
-
-static struct uart_8250_port serial8250_ports[UART_NR];
-
-static void __init serial8250_isa_init_ports(void)
-{
- struct uart_8250_port *up;
- static int first = 1;
- int i;
-
- if (!first)
- return;
- first = 0;
-
- for (i = 0, up = serial8250_ports; i < ARRAY_SIZE(old_serial_port);
- i++, up++) {
- up->port.iobase = old_serial_port[i].port;
- up->port.irq = old_serial_port[i].irq;
- up->port.uartclk = get_au1x00_uart_baud_base();
- up->port.flags = old_serial_port[i].flags;
- up->port.hub6 = old_serial_port[i].hub6;
- up->port.membase = old_serial_port[i].iomem_base;
- up->port.iotype = old_serial_port[i].io_type;
- up->port.regshift = old_serial_port[i].iomem_reg_shift;
- up->port.ops = &serial8250_pops;
- }
-}
-
-static void __init serial8250_register_ports(struct uart_driver *drv)
-{
- int i;
-
- serial8250_isa_init_ports();
-
- for (i = 0; i < UART_NR; i++) {
- struct uart_8250_port *up = &serial8250_ports[i];
-
- up->port.line = i;
- up->port.ops = &serial8250_pops;
- init_timer(&up->timer);
- up->timer.function = serial8250_timeout;
-
- /*
- * ALPHA_KLUDGE_MCR needs to be killed.
- */
- up->mcr_mask = ~ALPHA_KLUDGE_MCR;
- up->mcr_force = ALPHA_KLUDGE_MCR;
-
- uart_add_one_port(drv, &up->port);
- }
-}
-
-#ifdef CONFIG_SERIAL_AU1X00_CONSOLE
-
-#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
-
-/*
- * Wait for transmitter & holding register to empty
- */
-static inline void wait_for_xmitr(struct uart_8250_port *up)
-{
- unsigned int status, tmout = 10000;
-
- /* Wait up to 10ms for the character(s) to be sent. */
- do {
- status = serial_in(up, UART_LSR);
-
- if (status & UART_LSR_BI)
- up->lsr_break_flag = UART_LSR_BI;
-
- if (--tmout == 0)
- break;
- udelay(1);
- } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
-
- /* Wait up to 1s for flow control if necessary */
- if (up->port.flags & UPF_CONS_FLOW) {
- tmout = 1000000;
- while (--tmout &&
- ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
- udelay(1);
- }
-}
-
-static void au1x00_console_putchar(struct uart_port *port, int ch)
-{
- struct uart_8250_port *up = (struct uart_8250_port *)port;
-
- wait_for_xmitr(up);
- serial_out(up, UART_TX, ch);
-}
-
-/*
- * Print a string to the serial port trying not to disturb
- * any possible real use of the port...
- *
- * The console_lock must be held when we get here.
- */
-static void
-serial8250_console_write(struct console *co, const char *s, unsigned int count)
-{
- struct uart_8250_port *up = &serial8250_ports[co->index];
- unsigned int ier;
-
- /*
- * First save the UER then disable the interrupts
- */
- ier = serial_in(up, UART_IER);
- serial_out(up, UART_IER, 0);
-
- uart_console_write(&up->port, s, count, au1x00_console_putchar);
-
- /*
- * Finally, wait for transmitter to become empty
- * and restore the IER
- */
- wait_for_xmitr(up);
- serial_out(up, UART_IER, ier);
-}
-
-static int __init serial8250_console_setup(struct console *co, char *options)
-{
- struct uart_port *port;
- int baud = 9600;
- int bits = 8;
- int parity = 'n';
- int flow = 'n';
-
- /*
- * Check whether an invalid uart number has been specified, and
- * if so, search for the first available port that does have
- * console support.
- */
- if (co->index >= UART_NR)
- co->index = 0;
- port = &serial8250_ports[co->index].port;
-
- /*
- * Temporary fix.
- */
- spin_lock_init(&port->lock);
-
- if (options)
- uart_parse_options(options, &baud, &parity, &bits, &flow);
-
- return uart_set_options(port, co, baud, parity, bits, flow);
-}
-
-extern struct uart_driver serial8250_reg;
-static struct console serial8250_console = {
- .name = "ttyS",
- .write = serial8250_console_write,
- .device = uart_console_device,
- .setup = serial8250_console_setup,
- .flags = CON_PRINTBUFFER,
- .index = -1,
- .data = &serial8250_reg,
-};
-
-static int __init serial8250_console_init(void)
-{
- serial8250_isa_init_ports();
- register_console(&serial8250_console);
- return 0;
-}
-console_initcall(serial8250_console_init);
-
-#define SERIAL8250_CONSOLE &serial8250_console
-#else
-#define SERIAL8250_CONSOLE NULL
-#endif
-
-static struct uart_driver serial8250_reg = {
- .owner = THIS_MODULE,
- .driver_name = "serial",
- .devfs_name = "tts/",
- .dev_name = "ttyS",
- .major = TTY_MAJOR,
- .minor = 64,
- .nr = UART_NR,
- .cons = SERIAL8250_CONSOLE,
-};
-
-int __init early_serial_setup(struct uart_port *port)
-{
- serial8250_isa_init_ports();
- serial8250_ports[port->line].port = *port;
- serial8250_ports[port->line].port.ops = &serial8250_pops;
- return 0;
-}
-
-/**
- * serial8250_suspend_port - suspend one serial port
- * @line: serial line number
- * @level: the level of port suspension, as per uart_suspend_port
- *
- * Suspend one serial port.
- */
-void serial8250_suspend_port(int line)
-{
- uart_suspend_port(&serial8250_reg, &serial8250_ports[line].port);
-}
-
-/**
- * serial8250_resume_port - resume one serial port
- * @line: serial line number
- * @level: the level of port resumption, as per uart_resume_port
- *
- * Resume one serial port.
- */
-void serial8250_resume_port(int line)
-{
- uart_resume_port(&serial8250_reg, &serial8250_ports[line].port);
-}
-
-static int __init serial8250_init(void)
-{
- int ret, i;
-
- printk(KERN_INFO "Serial: Au1x00 driver\n");
-
- for (i = 0; i < NR_IRQS; i++)
- spin_lock_init(&irq_lists[i].lock);
-
- ret = uart_register_driver(&serial8250_reg);
- if (ret >= 0)
- serial8250_register_ports(&serial8250_reg);
-
- return ret;
-}
-
-static void __exit serial8250_exit(void)
-{
- int i;
-
- for (i = 0; i < UART_NR; i++)
- uart_remove_one_port(&serial8250_reg, &serial8250_ports[i].port);
-
- uart_unregister_driver(&serial8250_reg);
-}
-
-module_init(serial8250_init);
-module_exit(serial8250_exit);
-
-EXPORT_SYMBOL(serial8250_suspend_port);
-EXPORT_SYMBOL(serial8250_resume_port);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Au1x00 serial driver\n");
projects / linux-2.6-omap-h63xx.git / commitdiff