--- /dev/null
+#
+# Makefile for Xtensa-specific library files.
+#
+
+lib-y += memcopy.o memset.o checksum.o strcasecmp.o \
+ usercopy.o strncpy_user.o strnlen_user.o
+lib-$(CONFIG_PCI) += pci-auto.o
--- /dev/null
+/*
+ * INET An implementation of the TCP/IP protocol suite for the LINUX
+ * operating system. INET is implemented using the BSD Socket
+ * interface as the means of communication with the user level.
+ *
+ * IP/TCP/UDP checksumming routines
+ *
+ * Xtensa version: Copyright (C) 2001 Tensilica, Inc. by Kevin Chea
+ * Optimized by Joe Taylor
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <asm/errno.h>
+#include <linux/linkage.h>
+#define _ASMLANGUAGE
+#include <xtensa/config/core.h>
+
+/*
+ * computes a partial checksum, e.g. for TCP/UDP fragments
+ */
+
+/*
+ * unsigned int csum_partial(const unsigned char *buf, int len,
+ * unsigned int sum);
+ * a2 = buf
+ * a3 = len
+ * a4 = sum
+ *
+ * This function assumes 2- or 4-byte alignment. Other alignments will fail!
+ */
+
+/* ONES_ADD converts twos-complement math to ones-complement. */
+#define ONES_ADD(sum, val) \
+ add sum, sum, val ; \
+ bgeu sum, val, 99f ; \
+ addi sum, sum, 1 ; \
+99: ;
+
+.text
+ENTRY(csum_partial)
+ /*
+ * Experiments with Ethernet and SLIP connections show that buf
+ * is aligned on either a 2-byte or 4-byte boundary.
+ */
+ entry sp, 32
+ extui a5, a2, 0, 2
+ bnez a5, 8f /* branch if 2-byte aligned */
+ /* Fall-through on common case, 4-byte alignment */
+1:
+ srli a5, a3, 5 /* 32-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a5, 2f
+#else
+ beqz a5, 2f
+ slli a5, a5, 5
+ add a5, a5, a2 /* a5 = end of last 32-byte chunk */
+.Loop1:
+#endif
+ l32i a6, a2, 0
+ l32i a7, a2, 4
+ ONES_ADD(a4, a6)
+ ONES_ADD(a4, a7)
+ l32i a6, a2, 8
+ l32i a7, a2, 12
+ ONES_ADD(a4, a6)
+ ONES_ADD(a4, a7)
+ l32i a6, a2, 16
+ l32i a7, a2, 20
+ ONES_ADD(a4, a6)
+ ONES_ADD(a4, a7)
+ l32i a6, a2, 24
+ l32i a7, a2, 28
+ ONES_ADD(a4, a6)
+ ONES_ADD(a4, a7)
+ addi a2, a2, 4*8
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a5, .Loop1
+#endif
+2:
+ extui a5, a3, 2, 3 /* remaining 4-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a5, 3f
+#else
+ beqz a5, 3f
+ slli a5, a5, 2
+ add a5, a5, a2 /* a5 = end of last 4-byte chunk */
+.Loop2:
+#endif
+ l32i a6, a2, 0
+ ONES_ADD(a4, a6)
+ addi a2, a2, 4
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a5, .Loop2
+#endif
+3:
+ _bbci.l a3, 1, 5f /* remaining 2-byte chunk */
+ l16ui a6, a2, 0
+ ONES_ADD(a4, a6)
+ addi a2, a2, 2
+5:
+ _bbci.l a3, 0, 7f /* remaining 1-byte chunk */
+6: l8ui a6, a2, 0
+#ifdef __XTENSA_EB__
+ slli a6, a6, 8 /* load byte into bits 8..15 */
+#endif
+ ONES_ADD(a4, a6)
+7:
+ mov a2, a4
+ retw
+
+ /* uncommon case, buf is 2-byte aligned */
+8:
+ beqz a3, 7b /* branch if len == 0 */
+ beqi a3, 1, 6b /* branch if len == 1 */
+
+ extui a5, a2, 0, 1
+ bnez a5, 8f /* branch if 1-byte aligned */
+
+ l16ui a6, a2, 0 /* common case, len >= 2 */
+ ONES_ADD(a4, a6)
+ addi a2, a2, 2 /* adjust buf */
+ addi a3, a3, -2 /* adjust len */
+ j 1b /* now buf is 4-byte aligned */
+
+ /* case: odd-byte aligned, len > 1
+ * This case is dog slow, so don't give us an odd address.
+ * (I don't think this ever happens, but just in case.)
+ */
+8:
+ srli a5, a3, 2 /* 4-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a5, 2f
+#else
+ beqz a5, 2f
+ slli a5, a5, 2
+ add a5, a5, a2 /* a5 = end of last 4-byte chunk */
+.Loop3:
+#endif
+ l8ui a6, a2, 0 /* bits 24..31 */
+ l16ui a7, a2, 1 /* bits 8..23 */
+ l8ui a8, a2, 3 /* bits 0.. 8 */
+#ifdef __XTENSA_EB__
+ slli a6, a6, 24
+#else
+ slli a8, a8, 24
+#endif
+ slli a7, a7, 8
+ or a7, a7, a6
+ or a7, a7, a8
+ ONES_ADD(a4, a7)
+ addi a2, a2, 4
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a5, .Loop3
+#endif
+2:
+ _bbci.l a3, 1, 3f /* remaining 2-byte chunk, still odd addr */
+ l8ui a6, a2, 0
+ l8ui a7, a2, 1
+#ifdef __XTENSA_EB__
+ slli a6, a6, 8
+#else
+ slli a7, a7, 8
+#endif
+ or a7, a7, a6
+ ONES_ADD(a4, a7)
+ addi a2, a2, 2
+3:
+ j 5b /* branch to handle the remaining byte */
+
+
+
+/*
+ * Copy from ds while checksumming, otherwise like csum_partial
+ *
+ * The macros SRC and DST specify the type of access for the instruction.
+ * thus we can call a custom exception handler for each access type.
+ */
+
+#define SRC(y...) \
+ 9999: y; \
+ .section __ex_table, "a"; \
+ .long 9999b, 6001f ; \
+ .previous
+
+#define DST(y...) \
+ 9999: y; \
+ .section __ex_table, "a"; \
+ .long 9999b, 6002f ; \
+ .previous
+
+/*
+unsigned int csum_partial_copy_generic (const char *src, char *dst, int len,
+ int sum, int *src_err_ptr, int *dst_err_ptr)
+ a2 = src
+ a3 = dst
+ a4 = len
+ a5 = sum
+ a6 = src_err_ptr
+ a7 = dst_err_ptr
+ a8 = temp
+ a9 = temp
+ a10 = temp
+ a11 = original len for exception handling
+ a12 = original dst for exception handling
+
+ This function is optimized for 4-byte aligned addresses. Other
+ alignments work, but not nearly as efficiently.
+ */
+
+ENTRY(csum_partial_copy_generic)
+ entry sp, 32
+ mov a12, a3
+ mov a11, a4
+ or a10, a2, a3
+
+ /* We optimize the following alignment tests for the 4-byte
+ aligned case. Two bbsi.l instructions might seem more optimal
+ (commented out below). However, both labels 5: and 3: are out
+ of the imm8 range, so the assembler relaxes them into
+ equivalent bbci.l, j combinations, which is actually
+ slower. */
+
+ extui a9, a10, 0, 2
+ beqz a9, 1f /* branch if both are 4-byte aligned */
+ bbsi.l a10, 0, 5f /* branch if one address is odd */
+ j 3f /* one address is 2-byte aligned */
+
+/* _bbsi.l a10, 0, 5f */ /* branch if odd address */
+/* _bbsi.l a10, 1, 3f */ /* branch if 2-byte-aligned address */
+
+1:
+ /* src and dst are both 4-byte aligned */
+ srli a10, a4, 5 /* 32-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a10, 2f
+#else
+ beqz a10, 2f
+ slli a10, a10, 5
+ add a10, a10, a2 /* a10 = end of last 32-byte src chunk */
+.Loop5:
+#endif
+SRC( l32i a9, a2, 0 )
+SRC( l32i a8, a2, 4 )
+DST( s32i a9, a3, 0 )
+DST( s32i a8, a3, 4 )
+ ONES_ADD(a5, a9)
+ ONES_ADD(a5, a8)
+SRC( l32i a9, a2, 8 )
+SRC( l32i a8, a2, 12 )
+DST( s32i a9, a3, 8 )
+DST( s32i a8, a3, 12 )
+ ONES_ADD(a5, a9)
+ ONES_ADD(a5, a8)
+SRC( l32i a9, a2, 16 )
+SRC( l32i a8, a2, 20 )
+DST( s32i a9, a3, 16 )
+DST( s32i a8, a3, 20 )
+ ONES_ADD(a5, a9)
+ ONES_ADD(a5, a8)
+SRC( l32i a9, a2, 24 )
+SRC( l32i a8, a2, 28 )
+DST( s32i a9, a3, 24 )
+DST( s32i a8, a3, 28 )
+ ONES_ADD(a5, a9)
+ ONES_ADD(a5, a8)
+ addi a2, a2, 32
+ addi a3, a3, 32
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a10, .Loop5
+#endif
+2:
+ extui a10, a4, 2, 3 /* remaining 4-byte chunks */
+ extui a4, a4, 0, 2 /* reset len for general-case, 2-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a10, 3f
+#else
+ beqz a10, 3f
+ slli a10, a10, 2
+ add a10, a10, a2 /* a10 = end of last 4-byte src chunk */
+.Loop6:
+#endif
+SRC( l32i a9, a2, 0 )
+DST( s32i a9, a3, 0 )
+ ONES_ADD(a5, a9)
+ addi a2, a2, 4
+ addi a3, a3, 4
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a10, .Loop6
+#endif
+3:
+ /*
+ Control comes to here in two cases: (1) It may fall through
+ to here from the 4-byte alignment case to process, at most,
+ one 2-byte chunk. (2) It branches to here from above if
+ either src or dst is 2-byte aligned, and we process all bytes
+ here, except for perhaps a trailing odd byte. It's
+ inefficient, so align your addresses to 4-byte boundaries.
+
+ a2 = src
+ a3 = dst
+ a4 = len
+ a5 = sum
+ */
+ srli a10, a4, 1 /* 2-byte chunks */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a10, 4f
+#else
+ beqz a10, 4f
+ slli a10, a10, 1
+ add a10, a10, a2 /* a10 = end of last 2-byte src chunk */
+.Loop7:
+#endif
+SRC( l16ui a9, a2, 0 )
+DST( s16i a9, a3, 0 )
+ ONES_ADD(a5, a9)
+ addi a2, a2, 2
+ addi a3, a3, 2
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a10, .Loop7
+#endif
+4:
+ /* This section processes a possible trailing odd byte. */
+ _bbci.l a4, 0, 8f /* 1-byte chunk */
+SRC( l8ui a9, a2, 0 )
+DST( s8i a9, a3, 0 )
+#ifdef __XTENSA_EB__
+ slli a9, a9, 8 /* shift byte to bits 8..15 */
+#endif
+ ONES_ADD(a5, a9)
+8:
+ mov a2, a5
+ retw
+
+5:
+ /* Control branch to here when either src or dst is odd. We
+ process all bytes using 8-bit accesses. Grossly inefficient,
+ so don't feed us an odd address. */
+
+ srli a10, a4, 1 /* handle in pairs for 16-bit csum */
+#if XCHAL_HAVE_LOOPS
+ loopgtz a10, 6f
+#else
+ beqz a10, 6f
+ slli a10, a10, 1
+ add a10, a10, a2 /* a10 = end of last odd-aligned, 2-byte src chunk */
+.Loop8:
+#endif
+SRC( l8ui a9, a2, 0 )
+SRC( l8ui a8, a2, 1 )
+DST( s8i a9, a3, 0 )
+DST( s8i a8, a3, 1 )
+#ifdef __XTENSA_EB__
+ slli a9, a9, 8 /* combine into a single 16-bit value */
+#else /* for checksum computation */
+ slli a8, a8, 8
+#endif
+ or a9, a9, a8
+ ONES_ADD(a5, a9)
+ addi a2, a2, 2
+ addi a3, a3, 2
+#if !XCHAL_HAVE_LOOPS
+ blt a2, a10, .Loop8
+#endif
+6:
+ j 4b /* process the possible trailing odd byte */
+
+
+# Exception handler:
+.section .fixup, "ax"
+/*
+ a6 = src_err_ptr
+ a7 = dst_err_ptr
+ a11 = original len for exception handling
+ a12 = original dst for exception handling
+*/
+
+6001:
+ _movi a2, -EFAULT
+ s32i a2, a6, 0 /* src_err_ptr */
+
+ # clear the complete destination - computing the rest
+ # is too much work
+ movi a2, 0
+#if XCHAL_HAVE_LOOPS
+ loopgtz a11, 2f
+#else
+ beqz a11, 2f
+ add a11, a11, a12 /* a11 = ending address */
+.Leloop:
+#endif
+ s8i a2, a12, 0
+ addi a12, a12, 1
+#if !XCHAL_HAVE_LOOPS
+ blt a12, a11, .Leloop
+#endif
+2:
+ retw
+
+6002:
+ movi a2, -EFAULT
+ s32i a2, a7, 0 /* dst_err_ptr */
+ movi a2, 0
+ retw
+
+.previous
+
--- /dev/null
+/*
+ * arch/xtensa/lib/hal/memcopy.S -- Core HAL library functions
+ * xthal_memcpy and xthal_bcopy
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002 - 2005 Tensilica Inc.
+ */
+
+#include <xtensa/coreasm.h>
+
+ .macro src_b r, w0, w1
+#ifdef __XTENSA_EB__
+ src \r, \w0, \w1
+#else
+ src \r, \w1, \w0
+#endif
+ .endm
+
+ .macro ssa8 r
+#ifdef __XTENSA_EB__
+ ssa8b \r
+#else
+ ssa8l \r
+#endif
+ .endm
+
+
+/*
+ * void *memcpy(void *dst, const void *src, size_t len);
+ * void *memmove(void *dst, const void *src, size_t len);
+ * void *bcopy(const void *src, void *dst, size_t len);
+ *
+ * This function is intended to do the same thing as the standard
+ * library function memcpy() (or bcopy()) for most cases.
+ * However, where the source and/or destination references
+ * an instruction RAM or ROM or a data RAM or ROM, that
+ * source and/or destination will always be accessed with
+ * 32-bit load and store instructions (as required for these
+ * types of devices).
+ *
+ * !!!!!!! XTFIXME:
+ * !!!!!!! Handling of IRAM/IROM has not yet
+ * !!!!!!! been implemented.
+ *
+ * The bcopy version is provided here to avoid the overhead
+ * of an extra call, for callers that require this convention.
+ *
+ * The (general case) algorithm is as follows:
+ * If destination is unaligned, align it by conditionally
+ * copying 1 and 2 bytes.
+ * If source is aligned,
+ * do 16 bytes with a loop, and then finish up with
+ * 8, 4, 2, and 1 byte copies conditional on the length;
+ * else (if source is unaligned),
+ * do the same, but use SRC to align the source data.
+ * This code tries to use fall-through branches for the common
+ * case of aligned source and destination and multiple
+ * of 4 (or 8) length.
+ *
+ * Register use:
+ * a0/ return address
+ * a1/ stack pointer
+ * a2/ return value
+ * a3/ src
+ * a4/ length
+ * a5/ dst
+ * a6/ tmp
+ * a7/ tmp
+ * a8/ tmp
+ * a9/ tmp
+ * a10/ tmp
+ * a11/ tmp
+ */
+
+ .text
+ .align 4
+ .global bcopy
+ .type bcopy,@function
+bcopy:
+ entry sp, 16 # minimal stack frame
+ # a2=src, a3=dst, a4=len
+ mov a5, a3 # copy dst so that a2 is return value
+ mov a3, a2
+ mov a2, a5
+ j .Lcommon # go to common code for memcpy+bcopy
+
+
+/*
+ * Byte by byte copy
+ */
+ .align 4
+ .byte 0 # 1 mod 4 alignment for LOOPNEZ
+ # (0 mod 4 alignment for LBEG)
+.Lbytecopy:
+#if XCHAL_HAVE_LOOPS
+ loopnez a4, .Lbytecopydone
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a4, .Lbytecopydone
+ add a7, a3, a4 # a7 = end address for source
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lnextbyte:
+ l8ui a6, a3, 0
+ addi a3, a3, 1
+ s8i a6, a5, 0
+ addi a5, a5, 1
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a7, .Lnextbyte
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lbytecopydone:
+ retw
+
+/*
+ * Destination is unaligned
+ */
+
+ .align 4
+.Ldst1mod2: # dst is only byte aligned
+ _bltui a4, 7, .Lbytecopy # do short copies byte by byte
+
+ # copy 1 byte
+ l8ui a6, a3, 0
+ addi a3, a3, 1
+ addi a4, a4, -1
+ s8i a6, a5, 0
+ addi a5, a5, 1
+ _bbci.l a5, 1, .Ldstaligned # if dst is now aligned, then
+ # return to main algorithm
+.Ldst2mod4: # dst 16-bit aligned
+ # copy 2 bytes
+ _bltui a4, 6, .Lbytecopy # do short copies byte by byte
+ l8ui a6, a3, 0
+ l8ui a7, a3, 1
+ addi a3, a3, 2
+ addi a4, a4, -2
+ s8i a6, a5, 0
+ s8i a7, a5, 1
+ addi a5, a5, 2
+ j .Ldstaligned # dst is now aligned, return to main algorithm
+
+ .align 4
+ .global memcpy
+ .type memcpy,@function
+memcpy:
+ .global memmove
+ .type memmove,@function
+memmove:
+
+ entry sp, 16 # minimal stack frame
+ # a2/ dst, a3/ src, a4/ len
+ mov a5, a2 # copy dst so that a2 is return value
+.Lcommon:
+ _bbsi.l a2, 0, .Ldst1mod2 # if dst is 1 mod 2
+ _bbsi.l a2, 1, .Ldst2mod4 # if dst is 2 mod 4
+.Ldstaligned: # return here from .Ldst?mod? once dst is aligned
+ srli a7, a4, 4 # number of loop iterations with 16B
+ # per iteration
+ movi a8, 3 # if source is not aligned,
+ _bany a3, a8, .Lsrcunaligned # then use shifting copy
+ /*
+ * Destination and source are word-aligned, use word copy.
+ */
+ # copy 16 bytes per iteration for word-aligned dst and word-aligned src
+#if XCHAL_HAVE_LOOPS
+ loopnez a7, .Loop1done
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a7, .Loop1done
+ slli a8, a7, 4
+ add a8, a8, a3 # a8 = end of last 16B source chunk
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1:
+ l32i a6, a3, 0
+ l32i a7, a3, 4
+ s32i a6, a5, 0
+ l32i a6, a3, 8
+ s32i a7, a5, 4
+ l32i a7, a3, 12
+ s32i a6, a5, 8
+ addi a3, a3, 16
+ s32i a7, a5, 12
+ addi a5, a5, 16
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a8, .Loop1
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1done:
+ bbci.l a4, 3, .L2
+ # copy 8 bytes
+ l32i a6, a3, 0
+ l32i a7, a3, 4
+ addi a3, a3, 8
+ s32i a6, a5, 0
+ s32i a7, a5, 4
+ addi a5, a5, 8
+.L2:
+ bbsi.l a4, 2, .L3
+ bbsi.l a4, 1, .L4
+ bbsi.l a4, 0, .L5
+ retw
+.L3:
+ # copy 4 bytes
+ l32i a6, a3, 0
+ addi a3, a3, 4
+ s32i a6, a5, 0
+ addi a5, a5, 4
+ bbsi.l a4, 1, .L4
+ bbsi.l a4, 0, .L5
+ retw
+.L4:
+ # copy 2 bytes
+ l16ui a6, a3, 0
+ addi a3, a3, 2
+ s16i a6, a5, 0
+ addi a5, a5, 2
+ bbsi.l a4, 0, .L5
+ retw
+.L5:
+ # copy 1 byte
+ l8ui a6, a3, 0
+ s8i a6, a5, 0
+ retw
+
+/*
+ * Destination is aligned, Source is unaligned
+ */
+
+ .align 4
+.Lsrcunaligned:
+ _beqz a4, .Ldone # avoid loading anything for zero-length copies
+ # copy 16 bytes per iteration for word-aligned dst and unaligned src
+ ssa8 a3 # set shift amount from byte offset
+#define SIM_CHECKS_ALIGNMENT 1 /* set to 1 when running on ISS (simulator) with the
+ lint or ferret client, or 0 to save a few cycles */
+#if XCHAL_UNALIGNED_LOAD_EXCEPTION || SIM_CHECKS_ALIGNMENT
+ and a11, a3, a8 # save unalignment offset for below
+ sub a3, a3, a11 # align a3
+#endif
+ l32i a6, a3, 0 # load first word
+#if XCHAL_HAVE_LOOPS
+ loopnez a7, .Loop2done
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a7, .Loop2done
+ slli a10, a7, 4
+ add a10, a10, a3 # a10 = end of last 16B source chunk
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop2:
+ l32i a7, a3, 4
+ l32i a8, a3, 8
+ src_b a6, a6, a7
+ s32i a6, a5, 0
+ l32i a9, a3, 12
+ src_b a7, a7, a8
+ s32i a7, a5, 4
+ l32i a6, a3, 16
+ src_b a8, a8, a9
+ s32i a8, a5, 8
+ addi a3, a3, 16
+ src_b a9, a9, a6
+ s32i a9, a5, 12
+ addi a5, a5, 16
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a10, .Loop2
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop2done:
+ bbci.l a4, 3, .L12
+ # copy 8 bytes
+ l32i a7, a3, 4
+ l32i a8, a3, 8
+ src_b a6, a6, a7
+ s32i a6, a5, 0
+ addi a3, a3, 8
+ src_b a7, a7, a8
+ s32i a7, a5, 4
+ addi a5, a5, 8
+ mov a6, a8
+.L12:
+ bbci.l a4, 2, .L13
+ # copy 4 bytes
+ l32i a7, a3, 4
+ addi a3, a3, 4
+ src_b a6, a6, a7
+ s32i a6, a5, 0
+ addi a5, a5, 4
+ mov a6, a7
+.L13:
+#if XCHAL_UNALIGNED_LOAD_EXCEPTION || SIM_CHECKS_ALIGNMENT
+ add a3, a3, a11 # readjust a3 with correct misalignment
+#endif
+ bbsi.l a4, 1, .L14
+ bbsi.l a4, 0, .L15
+.Ldone: retw
+.L14:
+ # copy 2 bytes
+ l8ui a6, a3, 0
+ l8ui a7, a3, 1
+ addi a3, a3, 2
+ s8i a6, a5, 0
+ s8i a7, a5, 1
+ addi a5, a5, 2
+ bbsi.l a4, 0, .L15
+ retw
+.L15:
+ # copy 1 byte
+ l8ui a6, a3, 0
+ s8i a6, a5, 0
+ retw
+\f
+/*
+ * Local Variables:
+ * mode:fundamental
+ * comment-start: "# "
+ * comment-start-skip: "# *"
+ * End:
+ */
--- /dev/null
+/*
+ * arch/xtensa/lib/memset.S
+ *
+ * ANSI C standard library function memset
+ * (Well, almost. .fixup code might return zero.)
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of
+ * this archive for more details.
+ *
+ * Copyright (C) 2002 Tensilica Inc.
+ */
+
+#include <xtensa/coreasm.h>
+
+/*
+ * void *memset(void *dst, int c, size_t length)
+ *
+ * The algorithm is as follows:
+ * Create a word with c in all byte positions
+ * If the destination is aligned,
+ * do 16B chucks with a loop, and then finish up with
+ * 8B, 4B, 2B, and 1B stores conditional on the length.
+ * If destination is unaligned, align it by conditionally
+ * setting 1B and 2B and then go to aligned case.
+ * This code tries to use fall-through branches for the common
+ * case of an aligned destination (except for the branches to
+ * the alignment labels).
+ */
+
+/* Load or store instructions that may cause exceptions use the EX macro. */
+
+#define EX(insn,reg1,reg2,offset,handler) \
+9: insn reg1, reg2, offset; \
+ .section __ex_table, "a"; \
+ .word 9b, handler; \
+ .previous
+
+
+.text
+.align 4
+.global memset
+.type memset,@function
+memset:
+ entry sp, 16 # minimal stack frame
+ # a2/ dst, a3/ c, a4/ length
+ extui a3, a3, 0, 8 # mask to just 8 bits
+ slli a7, a3, 8 # duplicate character in all bytes of word
+ or a3, a3, a7 # ...
+ slli a7, a3, 16 # ...
+ or a3, a3, a7 # ...
+ mov a5, a2 # copy dst so that a2 is return value
+ movi a6, 3 # for alignment tests
+ bany a2, a6, .Ldstunaligned # if dst is unaligned
+.L0: # return here from .Ldstunaligned when dst is aligned
+ srli a7, a4, 4 # number of loop iterations with 16B
+ # per iteration
+ bnez a4, .Laligned
+ retw
+
+/*
+ * Destination is word-aligned.
+ */
+ # set 16 bytes per iteration for word-aligned dst
+ .align 4 # 1 mod 4 alignment for LOOPNEZ
+ .byte 0 # (0 mod 4 alignment for LBEG)
+.Laligned:
+#if XCHAL_HAVE_LOOPS
+ loopnez a7, .Loop1done
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a7, .Loop1done
+ slli a6, a7, 4
+ add a6, a6, a5 # a6 = end of last 16B chunk
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1:
+ EX(s32i, a3, a5, 0, memset_fixup)
+ EX(s32i, a3, a5, 4, memset_fixup)
+ EX(s32i, a3, a5, 8, memset_fixup)
+ EX(s32i, a3, a5, 12, memset_fixup)
+ addi a5, a5, 16
+#if !XCHAL_HAVE_LOOPS
+ blt a5, a6, .Loop1
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1done:
+ bbci.l a4, 3, .L2
+ # set 8 bytes
+ EX(s32i, a3, a5, 0, memset_fixup)
+ EX(s32i, a3, a5, 4, memset_fixup)
+ addi a5, a5, 8
+.L2:
+ bbci.l a4, 2, .L3
+ # set 4 bytes
+ EX(s32i, a3, a5, 0, memset_fixup)
+ addi a5, a5, 4
+.L3:
+ bbci.l a4, 1, .L4
+ # set 2 bytes
+ EX(s16i, a3, a5, 0, memset_fixup)
+ addi a5, a5, 2
+.L4:
+ bbci.l a4, 0, .L5
+ # set 1 byte
+ EX(s8i, a3, a5, 0, memset_fixup)
+.L5:
+.Lret1:
+ retw
+
+/*
+ * Destination is unaligned
+ */
+
+.Ldstunaligned:
+ bltui a4, 8, .Lbyteset # do short copies byte by byte
+ bbci.l a5, 0, .L20 # branch if dst alignment half-aligned
+ # dst is only byte aligned
+ # set 1 byte
+ EX(s8i, a3, a5, 0, memset_fixup)
+ addi a5, a5, 1
+ addi a4, a4, -1
+ # now retest if dst aligned
+ bbci.l a5, 1, .L0 # if now aligned, return to main algorithm
+.L20:
+ # dst half-aligned
+ # set 2 bytes
+ EX(s16i, a3, a5, 0, memset_fixup)
+ addi a5, a5, 2
+ addi a4, a4, -2
+ j .L0 # dst is now aligned, return to main algorithm
+
+/*
+ * Byte by byte set
+ */
+ .align 4
+ .byte 0 # 1 mod 4 alignment for LOOPNEZ
+ # (0 mod 4 alignment for LBEG)
+.Lbyteset:
+#if XCHAL_HAVE_LOOPS
+ loopnez a4, .Lbytesetdone
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a4, .Lbytesetdone
+ add a6, a5, a4 # a6 = ending address
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lbyteloop:
+ EX(s8i, a3, a5, 0, memset_fixup)
+ addi a5, a5, 1
+#if !XCHAL_HAVE_LOOPS
+ blt a5, a6, .Lbyteloop
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lbytesetdone:
+ retw
+
+
+ .section .fixup, "ax"
+ .align 4
+
+/* We return zero if a failure occurred. */
+
+memset_fixup:
+ movi a2, 0
+ retw
--- /dev/null
+/*
+ * arch/xtensa/kernel/pci-auto.c
+ *
+ * PCI autoconfiguration library
+ *
+ * Copyright (C) 2001 - 2005 Tensilica Inc.
+ *
+ * Chris Zankel <zankel@tensilica.com, cez@zankel.net>
+ *
+ * Based on work from Matt Porter <mporter@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <asm/pci-bridge.h>
+
+
+/*
+ *
+ * Setting up a PCI
+ *
+ * pci_ctrl->first_busno = <first bus number (0)>
+ * pci_ctrl->last_busno = <last bus number (0xff)>
+ * pci_ctrl->ops = <PCI config operations>
+ * pci_ctrl->map_irq = <function to return the interrupt number for a device>
+ *
+ * pci_ctrl->io_space.start = <IO space start address (PCI view)>
+ * pci_ctrl->io_space.end = <IO space end address (PCI view)>
+ * pci_ctrl->io_space.base = <IO space offset: address 0 from CPU space>
+ * pci_ctrl->mem_space.start = <MEM space start address (PCI view)>
+ * pci_ctrl->mem_space.end = <MEM space end address (PCI view)>
+ * pci_ctrl->mem_space.base = <MEM space offset: address 0 from CPU space>
+ *
+ * pcibios_init_resource(&pci_ctrl->io_resource, <IO space start>,
+ * <IO space end>, IORESOURCE_IO, "PCI host bridge");
+ * pcibios_init_resource(&pci_ctrl->mem_resources[0], <MEM space start>,
+ * <MEM space end>, IORESOURCE_MEM, "PCI host bridge");
+ *
+ * pci_ctrl->last_busno = pciauto_bus_scan(pci_ctrl,pci_ctrl->first_busno);
+ *
+ * int __init pciauto_bus_scan(struct pci_controller *pci_ctrl, int current_bus)
+ *
+ */
+
+
+/* define DEBUG to print some debugging messages. */
+
+#undef DEBUG
+
+#ifdef DEBUG
+# define DBG(x...) printk(x)
+#else
+# define DBG(x...)
+#endif
+
+static int pciauto_upper_iospc;
+static int pciauto_upper_memspc;
+
+static struct pci_dev pciauto_dev;
+static struct pci_bus pciauto_bus;
+
+/*
+ * Helper functions
+ */
+
+/* Initialize the bars of a PCI device. */
+
+static void __init
+pciauto_setup_bars(struct pci_dev *dev, int bar_limit)
+{
+ int bar_size;
+ int bar, bar_nr;
+ int *upper_limit;
+ int found_mem64 = 0;
+
+ for (bar = PCI_BASE_ADDRESS_0, bar_nr = 0;
+ bar <= bar_limit;
+ bar+=4, bar_nr++)
+ {
+ /* Tickle the BAR and get the size */
+ pci_write_config_dword(dev, bar, 0xffffffff);
+ pci_read_config_dword(dev, bar, &bar_size);
+
+ /* If BAR is not implemented go to the next BAR */
+ if (!bar_size)
+ continue;
+
+ /* Check the BAR type and set our address mask */
+ if (bar_size & PCI_BASE_ADDRESS_SPACE_IO)
+ {
+ bar_size &= PCI_BASE_ADDRESS_IO_MASK;
+ upper_limit = &pciauto_upper_iospc;
+ DBG("PCI Autoconfig: BAR %d, I/O, ", bar_nr);
+ }
+ else
+ {
+ if ((bar_size & PCI_BASE_ADDRESS_MEM_TYPE_MASK) ==
+ PCI_BASE_ADDRESS_MEM_TYPE_64)
+ found_mem64 = 1;
+
+ bar_size &= PCI_BASE_ADDRESS_MEM_MASK;
+ upper_limit = &pciauto_upper_memspc;
+ DBG("PCI Autoconfig: BAR %d, Mem, ", bar_nr);
+ }
+
+ /* Allocate a base address (bar_size is negative!) */
+ *upper_limit = (*upper_limit + bar_size) & bar_size;
+
+ /* Write it out and update our limit */
+ pci_write_config_dword(dev, bar, *upper_limit);
+
+ /*
+ * If we are a 64-bit decoder then increment to the
+ * upper 32 bits of the bar and force it to locate
+ * in the lower 4GB of memory.
+ */
+
+ if (found_mem64)
+ pci_write_config_dword(dev, (bar+=4), 0x00000000);
+
+ DBG("size=0x%x, address=0x%x\n", ~bar_size + 1, *upper_limit);
+ }
+}
+
+/* Initialize the interrupt number. */
+
+static void __init
+pciauto_setup_irq(struct pci_controller* pci_ctrl,struct pci_dev *dev,int devfn)
+{
+ u8 pin;
+ int irq = 0;
+
+ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+
+ /* Fix illegal pin numbers. */
+
+ if (pin == 0 || pin > 4)
+ pin = 1;
+
+ if (pci_ctrl->map_irq)
+ irq = pci_ctrl->map_irq(dev, PCI_SLOT(devfn), pin);
+
+ if (irq == -1)
+ irq = 0;
+
+ DBG("PCI Autoconfig: Interrupt %d, pin %d\n", irq, pin);
+
+ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
+}
+
+
+static void __init
+pciauto_prescan_setup_bridge(struct pci_dev *dev, int current_bus,
+ int sub_bus, int *iosave, int *memsave)
+{
+ /* Configure bus number registers */
+ pci_write_config_byte(dev, PCI_PRIMARY_BUS, current_bus);
+ pci_write_config_byte(dev, PCI_SECONDARY_BUS, sub_bus + 1);
+ pci_write_config_byte(dev, PCI_SUBORDINATE_BUS, 0xff);
+
+ /* Round memory allocator to 1MB boundary */
+ pciauto_upper_memspc &= ~(0x100000 - 1);
+ *memsave = pciauto_upper_memspc;
+
+ /* Round I/O allocator to 4KB boundary */
+ pciauto_upper_iospc &= ~(0x1000 - 1);
+ *iosave = pciauto_upper_iospc;
+
+ /* Set up memory and I/O filter limits, assume 32-bit I/O space */
+ pci_write_config_word(dev, PCI_MEMORY_LIMIT,
+ ((pciauto_upper_memspc - 1) & 0xfff00000) >> 16);
+ pci_write_config_byte(dev, PCI_IO_LIMIT,
+ ((pciauto_upper_iospc - 1) & 0x0000f000) >> 8);
+ pci_write_config_word(dev, PCI_IO_LIMIT_UPPER16,
+ ((pciauto_upper_iospc - 1) & 0xffff0000) >> 16);
+}
+
+static void __init
+pciauto_postscan_setup_bridge(struct pci_dev *dev, int current_bus, int sub_bus,
+ int *iosave, int *memsave)
+{
+ int cmdstat;
+
+ /* Configure bus number registers */
+ pci_write_config_byte(dev, PCI_SUBORDINATE_BUS, sub_bus);
+
+ /*
+ * Round memory allocator to 1MB boundary.
+ * If no space used, allocate minimum.
+ */
+ pciauto_upper_memspc &= ~(0x100000 - 1);
+ if (*memsave == pciauto_upper_memspc)
+ pciauto_upper_memspc -= 0x00100000;
+
+ pci_write_config_word(dev, PCI_MEMORY_BASE, pciauto_upper_memspc >> 16);
+
+ /* Allocate 1MB for pre-fretch */
+ pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT,
+ ((pciauto_upper_memspc - 1) & 0xfff00000) >> 16);
+
+ pciauto_upper_memspc -= 0x100000;
+
+ pci_write_config_word(dev, PCI_PREF_MEMORY_BASE,
+ pciauto_upper_memspc >> 16);
+
+ /* Round I/O allocator to 4KB boundary */
+ pciauto_upper_iospc &= ~(0x1000 - 1);
+ if (*iosave == pciauto_upper_iospc)
+ pciauto_upper_iospc -= 0x1000;
+
+ pci_write_config_byte(dev, PCI_IO_BASE,
+ (pciauto_upper_iospc & 0x0000f000) >> 8);
+ pci_write_config_word(dev, PCI_IO_BASE_UPPER16,
+ pciauto_upper_iospc >> 16);
+
+ /* Enable memory and I/O accesses, enable bus master */
+ pci_read_config_dword(dev, PCI_COMMAND, &cmdstat);
+ pci_write_config_dword(dev, PCI_COMMAND,
+ cmdstat |
+ PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY |
+ PCI_COMMAND_MASTER);
+}
+
+/*
+ * Scan the current PCI bus.
+ */
+
+
+int __init pciauto_bus_scan(struct pci_controller *pci_ctrl, int current_bus)
+{
+ int sub_bus, pci_devfn, pci_class, cmdstat, found_multi=0;
+ unsigned short vid;
+ unsigned char header_type;
+ struct pci_dev *dev = &pciauto_dev;
+
+ pciauto_dev.bus = &pciauto_bus;
+ pciauto_dev.sysdata = pci_ctrl;
+ pciauto_bus.ops = pci_ctrl->ops;
+
+ /*
+ * Fetch our I/O and memory space upper boundaries used
+ * to allocated base addresses on this pci_controller.
+ */
+
+ if (current_bus == pci_ctrl->first_busno)
+ {
+ pciauto_upper_iospc = pci_ctrl->io_resource.end + 1;
+ pciauto_upper_memspc = pci_ctrl->mem_resources[0].end + 1;
+ }
+
+ sub_bus = current_bus;
+
+ for (pci_devfn = 0; pci_devfn < 0xff; pci_devfn++)
+ {
+ /* Skip our host bridge */
+ if ((current_bus == pci_ctrl->first_busno) && (pci_devfn == 0))
+ continue;
+
+ if (PCI_FUNC(pci_devfn) && !found_multi)
+ continue;
+
+ pciauto_bus.number = current_bus;
+ pciauto_dev.devfn = pci_devfn;
+
+ /* If config space read fails from this device, move on */
+ if (pci_read_config_byte(dev, PCI_HEADER_TYPE, &header_type))
+ continue;
+
+ if (!PCI_FUNC(pci_devfn))
+ found_multi = header_type & 0x80;
+ pci_read_config_word(dev, PCI_VENDOR_ID, &vid);
+
+ if (vid == 0xffff || vid == 0x0000) {
+ found_multi = 0;
+ continue;
+ }
+
+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &pci_class);
+
+ if ((pci_class >> 16) == PCI_CLASS_BRIDGE_PCI) {
+
+ int iosave, memsave;
+
+ DBG("PCI Autoconfig: Found P2P bridge, device %d\n",
+ PCI_SLOT(pci_devfn));
+
+ /* Allocate PCI I/O and/or memory space */
+ pciauto_setup_bars(dev, PCI_BASE_ADDRESS_1);
+
+ pciauto_prescan_setup_bridge(dev, current_bus, sub_bus,
+ &iosave, &memsave);
+ sub_bus = pciauto_bus_scan(pci_ctrl, sub_bus+1);
+ pciauto_postscan_setup_bridge(dev, current_bus, sub_bus,
+ &iosave, &memsave);
+ pciauto_bus.number = current_bus;
+
+ continue;
+
+ }
+
+
+#if 0
+ /* Skip legacy mode IDE controller */
+
+ if ((pci_class >> 16) == PCI_CLASS_STORAGE_IDE) {
+
+ unsigned char prg_iface;
+ pci_read_config_byte(dev, PCI_CLASS_PROG, &prg_iface);
+
+ if (!(prg_iface & PCIAUTO_IDE_MODE_MASK)) {
+ DBG("PCI Autoconfig: Skipping legacy mode "
+ "IDE controller\n");
+ continue;
+ }
+ }
+#endif
+
+ /*
+ * Found a peripheral, enable some standard
+ * settings
+ */
+
+ pci_read_config_dword(dev, PCI_COMMAND, &cmdstat);
+ pci_write_config_dword(dev, PCI_COMMAND,
+ cmdstat |
+ PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY |
+ PCI_COMMAND_MASTER);
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x80);
+
+ /* Allocate PCI I/O and/or memory space */
+ DBG("PCI Autoconfig: Found Bus %d, Device %d, Function %d\n",
+ current_bus, PCI_SLOT(pci_devfn), PCI_FUNC(pci_devfn) );
+
+ pciauto_setup_bars(dev, PCI_BASE_ADDRESS_5);
+ pciauto_setup_irq(pci_ctrl, dev, pci_devfn);
+ }
+ return sub_bus;
+}
+
+
+
+
+
--- /dev/null
+/*
+ * linux/arch/xtensa/lib/strcasecmp.c
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of
+ * this archive for more details.
+ *
+ * Copyright (C) 2002 Tensilica Inc.
+ */
+
+#include <linux/string.h>
+
+
+/* We handle nothing here except the C locale. Since this is used in
+ only one place, on strings known to contain only 7 bit ASCII, this
+ is ok. */
+
+int strcasecmp(const char *a, const char *b)
+{
+ int ca, cb;
+
+ do {
+ ca = *a++ & 0xff;
+ cb = *b++ & 0xff;
+ if (ca >= 'A' && ca <= 'Z')
+ ca += 'a' - 'A';
+ if (cb >= 'A' && cb <= 'Z')
+ cb += 'a' - 'A';
+ } while (ca == cb && ca != '\0');
+
+ return ca - cb;
+}
--- /dev/null
+/*
+ * arch/xtensa/lib/strncpy_user.S
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of
+ * this archive for more details.
+ *
+ * Returns: -EFAULT if exception before terminator, N if the entire
+ * buffer filled, else strlen.
+ *
+ * Copyright (C) 2002 Tensilica Inc.
+ */
+
+#include <xtensa/coreasm.h>
+#include <linux/errno.h>
+
+/* Load or store instructions that may cause exceptions use the EX macro. */
+
+#define EX(insn,reg1,reg2,offset,handler) \
+9: insn reg1, reg2, offset; \
+ .section __ex_table, "a"; \
+ .word 9b, handler; \
+ .previous
+
+/*
+ * char *__strncpy_user(char *dst, const char *src, size_t len)
+ */
+.text
+.begin literal
+.align 4
+.Lmask0:
+ .byte 0xff, 0x00, 0x00, 0x00
+.Lmask1:
+ .byte 0x00, 0xff, 0x00, 0x00
+.Lmask2:
+ .byte 0x00, 0x00, 0xff, 0x00
+.Lmask3:
+ .byte 0x00, 0x00, 0x00, 0xff
+.end literal
+
+# Register use
+# a0/ return address
+# a1/ stack pointer
+# a2/ return value
+# a3/ src
+# a4/ len
+# a5/ mask0
+# a6/ mask1
+# a7/ mask2
+# a8/ mask3
+# a9/ tmp
+# a10/ tmp
+# a11/ dst
+# a12/ tmp
+
+.align 4
+.global __strncpy_user
+.type __strncpy_user,@function
+__strncpy_user:
+ entry sp, 16 # minimal stack frame
+ # a2/ dst, a3/ src, a4/ len
+ mov a11, a2 # leave dst in return value register
+ beqz a4, .Lret # if len is zero
+ l32r a5, .Lmask0 # mask for byte 0
+ l32r a6, .Lmask1 # mask for byte 1
+ l32r a7, .Lmask2 # mask for byte 2
+ l32r a8, .Lmask3 # mask for byte 3
+ bbsi.l a3, 0, .Lsrc1mod2 # if only 8-bit aligned
+ bbsi.l a3, 1, .Lsrc2mod4 # if only 16-bit aligned
+.Lsrcaligned: # return here when src is word-aligned
+ srli a12, a4, 2 # number of loop iterations with 4B per loop
+ movi a9, 3
+ bnone a11, a9, .Laligned
+ j .Ldstunaligned
+
+.Lsrc1mod2: # src address is odd
+ EX(l8ui, a9, a3, 0, fixup_l) # get byte 0
+ addi a3, a3, 1 # advance src pointer
+ EX(s8i, a9, a11, 0, fixup_s) # store byte 0
+ beqz a9, .Lret # if byte 0 is zero
+ addi a11, a11, 1 # advance dst pointer
+ addi a4, a4, -1 # decrement len
+ beqz a4, .Lret # if len is zero
+ bbci.l a3, 1, .Lsrcaligned # if src is now word-aligned
+
+.Lsrc2mod4: # src address is 2 mod 4
+ EX(l8ui, a9, a3, 0, fixup_l) # get byte 0
+ /* 1-cycle interlock */
+ EX(s8i, a9, a11, 0, fixup_s) # store byte 0
+ beqz a9, .Lret # if byte 0 is zero
+ addi a11, a11, 1 # advance dst pointer
+ addi a4, a4, -1 # decrement len
+ beqz a4, .Lret # if len is zero
+ EX(l8ui, a9, a3, 1, fixup_l) # get byte 0
+ addi a3, a3, 2 # advance src pointer
+ EX(s8i, a9, a11, 0, fixup_s) # store byte 0
+ beqz a9, .Lret # if byte 0 is zero
+ addi a11, a11, 1 # advance dst pointer
+ addi a4, a4, -1 # decrement len
+ bnez a4, .Lsrcaligned # if len is nonzero
+.Lret:
+ sub a2, a11, a2 # compute strlen
+ retw
+
+/*
+ * dst is word-aligned, src is word-aligned
+ */
+ .align 4 # 1 mod 4 alignment for LOOPNEZ
+ .byte 0 # (0 mod 4 alignment for LBEG)
+.Laligned:
+#if XCHAL_HAVE_LOOPS
+ loopnez a12, .Loop1done
+#else
+ beqz a12, .Loop1done
+ slli a12, a12, 2
+ add a12, a12, a11 # a12 = end of last 4B chunck
+#endif
+.Loop1:
+ EX(l32i, a9, a3, 0, fixup_l) # get word from src
+ addi a3, a3, 4 # advance src pointer
+ bnone a9, a5, .Lz0 # if byte 0 is zero
+ bnone a9, a6, .Lz1 # if byte 1 is zero
+ bnone a9, a7, .Lz2 # if byte 2 is zero
+ EX(s32i, a9, a11, 0, fixup_s) # store word to dst
+ bnone a9, a8, .Lz3 # if byte 3 is zero
+ addi a11, a11, 4 # advance dst pointer
+#if !XCHAL_HAVE_LOOPS
+ blt a11, a12, .Loop1
+#endif
+
+.Loop1done:
+ bbci.l a4, 1, .L100
+ # copy 2 bytes
+ EX(l16ui, a9, a3, 0, fixup_l)
+ addi a3, a3, 2 # advance src pointer
+#ifdef __XTENSA_EB__
+ bnone a9, a7, .Lz0 # if byte 2 is zero
+ bnone a9, a8, .Lz1 # if byte 3 is zero
+#else
+ bnone a9, a5, .Lz0 # if byte 0 is zero
+ bnone a9, a6, .Lz1 # if byte 1 is zero
+#endif
+ EX(s16i, a9, a11, 0, fixup_s)
+ addi a11, a11, 2 # advance dst pointer
+.L100:
+ bbci.l a4, 0, .Lret
+ EX(l8ui, a9, a3, 0, fixup_l)
+ /* slot */
+ EX(s8i, a9, a11, 0, fixup_s)
+ beqz a9, .Lret # if byte is zero
+ addi a11, a11, 1-3 # advance dst ptr 1, but also cancel
+ # the effect of adding 3 in .Lz3 code
+ /* fall thru to .Lz3 and "retw" */
+
+.Lz3: # byte 3 is zero
+ addi a11, a11, 3 # advance dst pointer
+ sub a2, a11, a2 # compute strlen
+ retw
+.Lz0: # byte 0 is zero
+#ifdef __XTENSA_EB__
+ movi a9, 0
+#endif /* __XTENSA_EB__ */
+ EX(s8i, a9, a11, 0, fixup_s)
+ sub a2, a11, a2 # compute strlen
+ retw
+.Lz1: # byte 1 is zero
+#ifdef __XTENSA_EB__
+ extui a9, a9, 16, 16
+#endif /* __XTENSA_EB__ */
+ EX(s16i, a9, a11, 0, fixup_s)
+ addi a11, a11, 1 # advance dst pointer
+ sub a2, a11, a2 # compute strlen
+ retw
+.Lz2: # byte 2 is zero
+#ifdef __XTENSA_EB__
+ extui a9, a9, 16, 16
+#endif /* __XTENSA_EB__ */
+ EX(s16i, a9, a11, 0, fixup_s)
+ movi a9, 0
+ EX(s8i, a9, a11, 2, fixup_s)
+ addi a11, a11, 2 # advance dst pointer
+ sub a2, a11, a2 # compute strlen
+ retw
+
+ .align 4 # 1 mod 4 alignment for LOOPNEZ
+ .byte 0 # (0 mod 4 alignment for LBEG)
+.Ldstunaligned:
+/*
+ * for now just use byte copy loop
+ */
+#if XCHAL_HAVE_LOOPS
+ loopnez a4, .Lunalignedend
+#else
+ beqz a4, .Lunalignedend
+ add a12, a11, a4 # a12 = ending address
+#endif /* XCHAL_HAVE_LOOPS */
+.Lnextbyte:
+ EX(l8ui, a9, a3, 0, fixup_l)
+ addi a3, a3, 1
+ EX(s8i, a9, a11, 0, fixup_s)
+ beqz a9, .Lunalignedend
+ addi a11, a11, 1
+#if !XCHAL_HAVE_LOOPS
+ blt a11, a12, .Lnextbyte
+#endif
+
+.Lunalignedend:
+ sub a2, a11, a2 # compute strlen
+ retw
+
+
+ .section .fixup, "ax"
+ .align 4
+
+ /* For now, just return -EFAULT. Future implementations might
+ * like to clear remaining kernel space, like the fixup
+ * implementation in memset(). Thus, we differentiate between
+ * load/store fixups. */
+
+fixup_s:
+fixup_l:
+ movi a2, -EFAULT
+ retw
+
--- /dev/null
+/*
+ * arch/xtensa/lib/strnlen_user.S
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of
+ * this archive for more details.
+ *
+ * Returns strnlen, including trailing zero terminator.
+ * Zero indicates error.
+ *
+ * Copyright (C) 2002 Tensilica Inc.
+ */
+
+#include <xtensa/coreasm.h>
+
+/* Load or store instructions that may cause exceptions use the EX macro. */
+
+#define EX(insn,reg1,reg2,offset,handler) \
+9: insn reg1, reg2, offset; \
+ .section __ex_table, "a"; \
+ .word 9b, handler; \
+ .previous
+
+/*
+ * size_t __strnlen_user(const char *s, size_t len)
+ */
+.text
+.begin literal
+.align 4
+.Lmask0:
+ .byte 0xff, 0x00, 0x00, 0x00
+.Lmask1:
+ .byte 0x00, 0xff, 0x00, 0x00
+.Lmask2:
+ .byte 0x00, 0x00, 0xff, 0x00
+.Lmask3:
+ .byte 0x00, 0x00, 0x00, 0xff
+.end literal
+
+# Register use:
+# a2/ src
+# a3/ len
+# a4/ tmp
+# a5/ mask0
+# a6/ mask1
+# a7/ mask2
+# a8/ mask3
+# a9/ tmp
+# a10/ tmp
+
+.align 4
+.global __strnlen_user
+.type __strnlen_user,@function
+__strnlen_user:
+ entry sp, 16 # minimal stack frame
+ # a2/ s, a3/ len
+ addi a4, a2, -4 # because we overincrement at the end;
+ # we compensate with load offsets of 4
+ l32r a5, .Lmask0 # mask for byte 0
+ l32r a6, .Lmask1 # mask for byte 1
+ l32r a7, .Lmask2 # mask for byte 2
+ l32r a8, .Lmask3 # mask for byte 3
+ bbsi.l a2, 0, .L1mod2 # if only 8-bit aligned
+ bbsi.l a2, 1, .L2mod4 # if only 16-bit aligned
+
+/*
+ * String is word-aligned.
+ */
+.Laligned:
+ srli a10, a3, 2 # number of loop iterations with 4B per loop
+#if XCHAL_HAVE_LOOPS
+ loopnez a10, .Ldone
+#else
+ beqz a10, .Ldone
+ slli a10, a10, 2
+ add a10, a10, a4 # a10 = end of last 4B chunk
+#endif /* XCHAL_HAVE_LOOPS */
+.Loop:
+ EX(l32i, a9, a4, 4, lenfixup) # get next word of string
+ addi a4, a4, 4 # advance string pointer
+ bnone a9, a5, .Lz0 # if byte 0 is zero
+ bnone a9, a6, .Lz1 # if byte 1 is zero
+ bnone a9, a7, .Lz2 # if byte 2 is zero
+ bnone a9, a8, .Lz3 # if byte 3 is zero
+#if !XCHAL_HAVE_LOOPS
+ blt a4, a10, .Loop
+#endif
+
+.Ldone:
+ EX(l32i, a9, a4, 4, lenfixup) # load 4 bytes for remaining checks
+
+ bbci.l a3, 1, .L100
+ # check two more bytes (bytes 0, 1 of word)
+ addi a4, a4, 2 # advance string pointer
+ bnone a9, a5, .Lz0 # if byte 0 is zero
+ bnone a9, a6, .Lz1 # if byte 1 is zero
+.L100:
+ bbci.l a3, 0, .L101
+ # check one more byte (byte 2 of word)
+ # Actually, we don't need to check. Zero or nonzero, we'll add one.
+ # Do not add an extra one for the NULL terminator since we have
+ # exhausted the original len parameter.
+ addi a4, a4, 1 # advance string pointer
+.L101:
+ sub a2, a4, a2 # compute length
+ retw
+
+# NOTE that in several places below, we point to the byte just after
+# the zero byte in order to include the NULL terminator in the count.
+
+.Lz3: # byte 3 is zero
+ addi a4, a4, 3 # point to zero byte
+.Lz0: # byte 0 is zero
+ addi a4, a4, 1 # point just beyond zero byte
+ sub a2, a4, a2 # subtract to get length
+ retw
+.Lz1: # byte 1 is zero
+ addi a4, a4, 1+1 # point just beyond zero byte
+ sub a2, a4, a2 # subtract to get length
+ retw
+.Lz2: # byte 2 is zero
+ addi a4, a4, 2+1 # point just beyond zero byte
+ sub a2, a4, a2 # subtract to get length
+ retw
+
+.L1mod2: # address is odd
+ EX(l8ui, a9, a4, 4, lenfixup) # get byte 0
+ addi a4, a4, 1 # advance string pointer
+ beqz a9, .Lz3 # if byte 0 is zero
+ bbci.l a4, 1, .Laligned # if string pointer is now word-aligned
+
+.L2mod4: # address is 2 mod 4
+ addi a4, a4, 2 # advance ptr for aligned access
+ EX(l32i, a9, a4, 0, lenfixup) # get word with first two bytes of string
+ bnone a9, a7, .Lz2 # if byte 2 (of word, not string) is zero
+ bany a9, a8, .Laligned # if byte 3 (of word, not string) is nonzero
+ # byte 3 is zero
+ addi a4, a4, 3+1 # point just beyond zero byte
+ sub a2, a4, a2 # subtract to get length
+ retw
+
+ .section .fixup, "ax"
+ .align 4
+lenfixup:
+ movi a2, 0
+ retw
+
--- /dev/null
+/*
+ * arch/xtensa/lib/usercopy.S
+ *
+ * Copy to/from user space (derived from arch/xtensa/lib/hal/memcopy.S)
+ *
+ * DO NOT COMBINE this function with <arch/xtensa/lib/hal/memcopy.S>.
+ * It needs to remain separate and distinct. The hal files are part
+ * of the the Xtensa link-time HAL, and those files may differ per
+ * processor configuration. Patching the kernel for another
+ * processor configuration includes replacing the hal files, and we
+ * could loose the special functionality for accessing user-space
+ * memory during such a patch. We sacrifice a little code space here
+ * in favor to simplify code maintenance.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of
+ * this archive for more details.
+ *
+ * Copyright (C) 2002 Tensilica Inc.
+ */
+
+
+/*
+ * size_t __xtensa_copy_user (void *dst, const void *src, size_t len);
+ *
+ * The returned value is the number of bytes not copied. Implies zero
+ * is success.
+ *
+ * The general case algorithm is as follows:
+ * If the destination and source are both aligned,
+ * do 16B chunks with a loop, and then finish up with
+ * 8B, 4B, 2B, and 1B copies conditional on the length.
+ * If destination is aligned and source unaligned,
+ * do the same, but use SRC to align the source data.
+ * If destination is unaligned, align it by conditionally
+ * copying 1B and 2B and then retest.
+ * This code tries to use fall-through braches for the common
+ * case of aligned destinations (except for the branches to
+ * the alignment label).
+ *
+ * Register use:
+ * a0/ return address
+ * a1/ stack pointer
+ * a2/ return value
+ * a3/ src
+ * a4/ length
+ * a5/ dst
+ * a6/ tmp
+ * a7/ tmp
+ * a8/ tmp
+ * a9/ tmp
+ * a10/ tmp
+ * a11/ original length
+ */
+
+#include <xtensa/coreasm.h>
+
+#ifdef __XTENSA_EB__
+#define ALIGN(R, W0, W1) src R, W0, W1
+#define SSA8(R) ssa8b R
+#else
+#define ALIGN(R, W0, W1) src R, W1, W0
+#define SSA8(R) ssa8l R
+#endif
+
+/* Load or store instructions that may cause exceptions use the EX macro. */
+
+#define EX(insn,reg1,reg2,offset,handler) \
+9: insn reg1, reg2, offset; \
+ .section __ex_table, "a"; \
+ .word 9b, handler; \
+ .previous
+
+
+ .text
+ .align 4
+ .global __xtensa_copy_user
+ .type __xtensa_copy_user,@function
+__xtensa_copy_user:
+ entry sp, 16 # minimal stack frame
+ # a2/ dst, a3/ src, a4/ len
+ mov a5, a2 # copy dst so that a2 is return value
+ mov a11, a4 # preserve original len for error case
+.Lcommon:
+ bbsi.l a2, 0, .Ldst1mod2 # if dst is 1 mod 2
+ bbsi.l a2, 1, .Ldst2mod4 # if dst is 2 mod 4
+.Ldstaligned: # return here from .Ldstunaligned when dst is aligned
+ srli a7, a4, 4 # number of loop iterations with 16B
+ # per iteration
+ movi a8, 3 # if source is also aligned,
+ bnone a3, a8, .Laligned # then use word copy
+ SSA8( a3) # set shift amount from byte offset
+ bnez a4, .Lsrcunaligned
+ movi a2, 0 # return success for len==0
+ retw
+
+/*
+ * Destination is unaligned
+ */
+
+.Ldst1mod2: # dst is only byte aligned
+ bltui a4, 7, .Lbytecopy # do short copies byte by byte
+
+ # copy 1 byte
+ EX(l8ui, a6, a3, 0, l_fixup)
+ addi a3, a3, 1
+ EX(s8i, a6, a5, 0, s_fixup)
+ addi a5, a5, 1
+ addi a4, a4, -1
+ bbci.l a5, 1, .Ldstaligned # if dst is now aligned, then
+ # return to main algorithm
+.Ldst2mod4: # dst 16-bit aligned
+ # copy 2 bytes
+ bltui a4, 6, .Lbytecopy # do short copies byte by byte
+ EX(l8ui, a6, a3, 0, l_fixup)
+ EX(l8ui, a7, a3, 1, l_fixup)
+ addi a3, a3, 2
+ EX(s8i, a6, a5, 0, s_fixup)
+ EX(s8i, a7, a5, 1, s_fixup)
+ addi a5, a5, 2
+ addi a4, a4, -2
+ j .Ldstaligned # dst is now aligned, return to main algorithm
+
+/*
+ * Byte by byte copy
+ */
+ .align 4
+ .byte 0 # 1 mod 4 alignment for LOOPNEZ
+ # (0 mod 4 alignment for LBEG)
+.Lbytecopy:
+#if XCHAL_HAVE_LOOPS
+ loopnez a4, .Lbytecopydone
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a4, .Lbytecopydone
+ add a7, a3, a4 # a7 = end address for source
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lnextbyte:
+ EX(l8ui, a6, a3, 0, l_fixup)
+ addi a3, a3, 1
+ EX(s8i, a6, a5, 0, s_fixup)
+ addi a5, a5, 1
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a7, .Lnextbyte
+#endif /* !XCHAL_HAVE_LOOPS */
+.Lbytecopydone:
+ movi a2, 0 # return success for len bytes copied
+ retw
+
+/*
+ * Destination and source are word-aligned.
+ */
+ # copy 16 bytes per iteration for word-aligned dst and word-aligned src
+ .align 4 # 1 mod 4 alignment for LOOPNEZ
+ .byte 0 # (0 mod 4 alignment for LBEG)
+.Laligned:
+#if XCHAL_HAVE_LOOPS
+ loopnez a7, .Loop1done
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a7, .Loop1done
+ slli a8, a7, 4
+ add a8, a8, a3 # a8 = end of last 16B source chunk
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1:
+ EX(l32i, a6, a3, 0, l_fixup)
+ EX(l32i, a7, a3, 4, l_fixup)
+ EX(s32i, a6, a5, 0, s_fixup)
+ EX(l32i, a6, a3, 8, l_fixup)
+ EX(s32i, a7, a5, 4, s_fixup)
+ EX(l32i, a7, a3, 12, l_fixup)
+ EX(s32i, a6, a5, 8, s_fixup)
+ addi a3, a3, 16
+ EX(s32i, a7, a5, 12, s_fixup)
+ addi a5, a5, 16
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a8, .Loop1
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop1done:
+ bbci.l a4, 3, .L2
+ # copy 8 bytes
+ EX(l32i, a6, a3, 0, l_fixup)
+ EX(l32i, a7, a3, 4, l_fixup)
+ addi a3, a3, 8
+ EX(s32i, a6, a5, 0, s_fixup)
+ EX(s32i, a7, a5, 4, s_fixup)
+ addi a5, a5, 8
+.L2:
+ bbci.l a4, 2, .L3
+ # copy 4 bytes
+ EX(l32i, a6, a3, 0, l_fixup)
+ addi a3, a3, 4
+ EX(s32i, a6, a5, 0, s_fixup)
+ addi a5, a5, 4
+.L3:
+ bbci.l a4, 1, .L4
+ # copy 2 bytes
+ EX(l16ui, a6, a3, 0, l_fixup)
+ addi a3, a3, 2
+ EX(s16i, a6, a5, 0, s_fixup)
+ addi a5, a5, 2
+.L4:
+ bbci.l a4, 0, .L5
+ # copy 1 byte
+ EX(l8ui, a6, a3, 0, l_fixup)
+ EX(s8i, a6, a5, 0, s_fixup)
+.L5:
+ movi a2, 0 # return success for len bytes copied
+ retw
+
+/*
+ * Destination is aligned, Source is unaligned
+ */
+
+ .align 4
+ .byte 0 # 1 mod 4 alignement for LOOPNEZ
+ # (0 mod 4 alignment for LBEG)
+.Lsrcunaligned:
+ # copy 16 bytes per iteration for word-aligned dst and unaligned src
+ and a10, a3, a8 # save unalignment offset for below
+ sub a3, a3, a10 # align a3 (to avoid sim warnings only; not needed for hardware)
+ EX(l32i, a6, a3, 0, l_fixup) # load first word
+#if XCHAL_HAVE_LOOPS
+ loopnez a7, .Loop2done
+#else /* !XCHAL_HAVE_LOOPS */
+ beqz a7, .Loop2done
+ slli a10, a7, 4
+ add a10, a10, a3 # a10 = end of last 16B source chunk
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop2:
+ EX(l32i, a7, a3, 4, l_fixup)
+ EX(l32i, a8, a3, 8, l_fixup)
+ ALIGN( a6, a6, a7)
+ EX(s32i, a6, a5, 0, s_fixup)
+ EX(l32i, a9, a3, 12, l_fixup)
+ ALIGN( a7, a7, a8)
+ EX(s32i, a7, a5, 4, s_fixup)
+ EX(l32i, a6, a3, 16, l_fixup)
+ ALIGN( a8, a8, a9)
+ EX(s32i, a8, a5, 8, s_fixup)
+ addi a3, a3, 16
+ ALIGN( a9, a9, a6)
+ EX(s32i, a9, a5, 12, s_fixup)
+ addi a5, a5, 16
+#if !XCHAL_HAVE_LOOPS
+ blt a3, a10, .Loop2
+#endif /* !XCHAL_HAVE_LOOPS */
+.Loop2done:
+ bbci.l a4, 3, .L12
+ # copy 8 bytes
+ EX(l32i, a7, a3, 4, l_fixup)
+ EX(l32i, a8, a3, 8, l_fixup)
+ ALIGN( a6, a6, a7)
+ EX(s32i, a6, a5, 0, s_fixup)
+ addi a3, a3, 8
+ ALIGN( a7, a7, a8)
+ EX(s32i, a7, a5, 4, s_fixup)
+ addi a5, a5, 8
+ mov a6, a8
+.L12:
+ bbci.l a4, 2, .L13
+ # copy 4 bytes
+ EX(l32i, a7, a3, 4, l_fixup)
+ addi a3, a3, 4
+ ALIGN( a6, a6, a7)
+ EX(s32i, a6, a5, 0, s_fixup)
+ addi a5, a5, 4
+ mov a6, a7
+.L13:
+ add a3, a3, a10 # readjust a3 with correct misalignment
+ bbci.l a4, 1, .L14
+ # copy 2 bytes
+ EX(l8ui, a6, a3, 0, l_fixup)
+ EX(l8ui, a7, a3, 1, l_fixup)
+ addi a3, a3, 2
+ EX(s8i, a6, a5, 0, s_fixup)
+ EX(s8i, a7, a5, 1, s_fixup)
+ addi a5, a5, 2
+.L14:
+ bbci.l a4, 0, .L15
+ # copy 1 byte
+ EX(l8ui, a6, a3, 0, l_fixup)
+ EX(s8i, a6, a5, 0, s_fixup)
+.L15:
+ movi a2, 0 # return success for len bytes copied
+ retw
+
+
+ .section .fixup, "ax"
+ .align 4
+
+/* a2 = original dst; a5 = current dst; a11= original len
+ * bytes_copied = a5 - a2
+ * retval = bytes_not_copied = original len - bytes_copied
+ * retval = a11 - (a5 - a2)
+ *
+ * Clearing the remaining pieces of kernel memory plugs security
+ * holes. This functionality is the equivalent of the *_zeroing
+ * functions that some architectures provide.
+ */
+
+.Lmemset:
+ .word memset
+
+s_fixup:
+ sub a2, a5, a2 /* a2 <-- bytes copied */
+ sub a2, a11, a2 /* a2 <-- bytes not copied */
+ retw
+
+l_fixup:
+ sub a2, a5, a2 /* a2 <-- bytes copied */
+ sub a2, a11, a2 /* a2 <-- bytes not copied == return value */
+
+ /* void *memset(void *s, int c, size_t n); */
+ mov a6, a5 /* s */
+ movi a7, 0 /* c */
+ mov a8, a2 /* n */
+ l32r a4, .Lmemset
+ callx4 a4
+ /* Ignore memset return value in a6. */
+ /* a2 still contains bytes not copied. */
+ retw
+
projects / linux-2.6-omap-h63xx.git / commitdiff