+obj-$(CONFIG_ATMEL_TCB_CLKSRC) += tcb_clksrc.o
obj-$(CONFIG_X86_CYCLONE_TIMER) += cyclone.o
obj-$(CONFIG_X86_PM_TIMER) += acpi_pm.o
obj-$(CONFIG_SCx200HR_TIMER) += scx200_hrt.o
--- /dev/null
+#include <linux/init.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/atmel_tc.h>
+
+
+/*
+ * We're configured to use a specific TC block, one that's not hooked
+ * up to external hardware, to provide a time solution:
+ *
+ * - Two channels combine to create a free-running 32 bit counter
+ * with a base rate of 5+ MHz, packaged as a clocksource (with
+ * resolution better than 200 nsec).
+ *
+ * - The third channel may be used to provide a 16-bit clockevent
+ * source, used in either periodic or oneshot mode. This runs
+ * at 32 KiHZ, and can handle delays of up to two seconds.
+ *
+ * A boot clocksource and clockevent source are also currently needed,
+ * unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so
+ * this code can be used when init_timers() is called, well before most
+ * devices are set up. (Some low end AT91 parts, which can run uClinux,
+ * have only the timers in one TC block... they currently don't support
+ * the tclib code, because of that initialization issue.)
+ *
+ * REVISIT behavior during system suspend states... we should disable
+ * all clocks and save the power. Easily done for clockevent devices,
+ * but clocksources won't necessarily get the needed notifications.
+ * For deeper system sleep states, this will be mandatory...
+ */
+
+static void __iomem *tcaddr;
+
+static cycle_t tc_get_cycles(void)
+{
+ unsigned long flags;
+ u32 lower, upper;
+
+ raw_local_irq_save(flags);
+ do {
+ upper = __raw_readl(tcaddr + ATMEL_TC_REG(1, CV));
+ lower = __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
+ } while (upper != __raw_readl(tcaddr + ATMEL_TC_REG(1, CV)));
+
+ raw_local_irq_restore(flags);
+ return (upper << 16) | lower;
+}
+
+static struct clocksource clksrc = {
+ .name = "tcb_clksrc",
+ .rating = 200,
+ .read = tc_get_cycles,
+ .mask = CLOCKSOURCE_MASK(32),
+ .shift = 18,
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+
+struct tc_clkevt_device {
+ struct clock_event_device clkevt;
+ struct clk *clk;
+ void __iomem *regs;
+};
+
+static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt)
+{
+ return container_of(clkevt, struct tc_clkevt_device, clkevt);
+}
+
+/* For now, we always use the 32K clock ... this optimizes for NO_HZ,
+ * because using one of the divided clocks would usually mean the
+ * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
+ *
+ * A divided clock could be good for high resolution timers, since
+ * 30.5 usec resolution can seem "low".
+ */
+static u32 timer_clock;
+
+static void tc_mode(enum clock_event_mode m, struct clock_event_device *d)
+{
+ struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+ void __iomem *regs = tcd->regs;
+
+ if (tcd->clkevt.mode == CLOCK_EVT_MODE_PERIODIC
+ || tcd->clkevt.mode == CLOCK_EVT_MODE_ONESHOT) {
+ __raw_writel(0xff, regs + ATMEL_TC_REG(2, IDR));
+ __raw_writel(ATMEL_TC_CLKDIS, regs + ATMEL_TC_REG(2, CCR));
+ clk_disable(tcd->clk);
+ }
+
+ switch (m) {
+
+ /* By not making the gentime core emulate periodic mode on top
+ * of oneshot, we get lower overhead and improved accuracy.
+ */
+ case CLOCK_EVT_MODE_PERIODIC:
+ clk_enable(tcd->clk);
+
+ /* slow clock, count up to RC, then irq and restart */
+ __raw_writel(timer_clock
+ | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+ regs + ATMEL_TC_REG(2, CMR));
+ __raw_writel((32768 + HZ/2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
+
+ /* Enable clock and interrupts on RC compare */
+ __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+ /* go go gadget! */
+ __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+ regs + ATMEL_TC_REG(2, CCR));
+ break;
+
+ case CLOCK_EVT_MODE_ONESHOT:
+ clk_enable(tcd->clk);
+
+ /* slow clock, count up to RC, then irq and stop */
+ __raw_writel(timer_clock | ATMEL_TC_CPCSTOP
+ | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+ regs + ATMEL_TC_REG(2, CMR));
+ __raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+ /* set_next_event() configures and starts the timer */
+ break;
+
+ default:
+ break;
+ }
+}
+
+static int tc_next_event(unsigned long delta, struct clock_event_device *d)
+{
+ __raw_writel(delta, tcaddr + ATMEL_TC_REG(2, RC));
+
+ /* go go gadget! */
+ __raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+ tcaddr + ATMEL_TC_REG(2, CCR));
+ return 0;
+}
+
+static struct tc_clkevt_device clkevt = {
+ .clkevt = {
+ .name = "tc_clkevt",
+ .features = CLOCK_EVT_FEAT_PERIODIC
+ | CLOCK_EVT_FEAT_ONESHOT,
+ .shift = 32,
+ /* Should be lower than at91rm9200's system timer */
+ .rating = 125,
+ .cpumask = CPU_MASK_CPU0,
+ .set_next_event = tc_next_event,
+ .set_mode = tc_mode,
+ },
+};
+
+static irqreturn_t ch2_irq(int irq, void *handle)
+{
+ struct tc_clkevt_device *dev = handle;
+ unsigned int sr;
+
+ sr = __raw_readl(dev->regs + ATMEL_TC_REG(2, SR));
+ if (sr & ATMEL_TC_CPCS) {
+ dev->clkevt.event_handler(&dev->clkevt);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+static struct irqaction tc_irqaction = {
+ .name = "tc_clkevt",
+ .flags = IRQF_TIMER | IRQF_DISABLED,
+ .handler = ch2_irq,
+};
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+ struct clk *t2_clk = tc->clk[2];
+ int irq = tc->irq[2];
+
+ clkevt.regs = tc->regs;
+ clkevt.clk = t2_clk;
+ tc_irqaction.dev_id = &clkevt;
+
+ timer_clock = clk32k_divisor_idx;
+
+ clkevt.clkevt.mult = div_sc(32768, NSEC_PER_SEC, clkevt.clkevt.shift);
+ clkevt.clkevt.max_delta_ns
+ = clockevent_delta2ns(0xffff, &clkevt.clkevt);
+ clkevt.clkevt.min_delta_ns = clockevent_delta2ns(1, &clkevt.clkevt) + 1;
+
+ setup_irq(irq, &tc_irqaction);
+
+ clockevents_register_device(&clkevt.clkevt);
+}
+
+#else /* !CONFIG_GENERIC_CLOCKEVENTS */
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+ /* NOTHING */
+}
+
+#endif
+
+static int __init tcb_clksrc_init(void)
+{
+ static char bootinfo[] __initdata
+ = KERN_DEBUG "%s: tc%d at %d.%03d MHz\n";
+
+ struct platform_device *pdev;
+ struct atmel_tc *tc;
+ struct clk *t0_clk;
+ u32 rate, divided_rate = 0;
+ int best_divisor_idx = -1;
+ int clk32k_divisor_idx = -1;
+ int i;
+
+ tc = atmel_tc_alloc(CONFIG_ATMEL_TCB_CLKSRC_BLOCK, clksrc.name);
+ if (!tc) {
+ pr_debug("can't alloc TC for clocksource\n");
+ return -ENODEV;
+ }
+ tcaddr = tc->regs;
+ pdev = tc->pdev;
+
+ t0_clk = tc->clk[0];
+ clk_enable(t0_clk);
+
+ /* How fast will we be counting? Pick something over 5 MHz. */
+ rate = (u32) clk_get_rate(t0_clk);
+ for (i = 0; i < 5; i++) {
+ unsigned divisor = atmel_tc_divisors[i];
+ unsigned tmp;
+
+ /* remember 32 KiHz clock for later */
+ if (!divisor) {
+ clk32k_divisor_idx = i;
+ continue;
+ }
+
+ tmp = rate / divisor;
+ pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
+ if (best_divisor_idx > 0) {
+ if (tmp < 5 * 1000 * 1000)
+ continue;
+ }
+ divided_rate = tmp;
+ best_divisor_idx = i;
+ }
+
+ clksrc.mult = clocksource_hz2mult(divided_rate, clksrc.shift);
+
+ printk(bootinfo, clksrc.name, CONFIG_ATMEL_TCB_CLKSRC_BLOCK,
+ divided_rate / 1000000,
+ ((divided_rate + 500000) % 1000000) / 1000);
+
+ /* tclib will give us three clocks no matter what the
+ * underlying platform supports.
+ */
+ clk_enable(tc->clk[1]);
+
+ /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
+ __raw_writel(best_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP /* free-run */
+ | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
+ | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
+ __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* channel 1: waveform mode, input TIOA0 */
+ __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(1, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
+
+ /* chain channel 0 to channel 1, then reset all the timers */
+ __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+
+ /* and away we go! */
+ clocksource_register(&clksrc);
+
+ /* channel 2: periodic and oneshot timer support */
+ setup_clkevents(tc, clk32k_divisor_idx);
+
+ return 0;
+}
+arch_initcall(tcb_clksrc_init);
purposes including software controlled power-efficent backlights
on LCD displays, motor control, and waveform generation.
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+
config IBM_ASM
tristate "Device driver for IBM RSA service processor"
depends on X86 && PCI && INPUT && EXPERIMENTAL
obj-$(CONFIG_ASUS_LAPTOP) += asus-laptop.o
obj-$(CONFIG_ATMEL_PWM) += atmel_pwm.o
obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o
+obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o
obj-$(CONFIG_TC1100_WMI) += tc1100-wmi.o
obj-$(CONFIG_LKDTM) += lkdtm.o
obj-$(CONFIG_TIFM_CORE) += tifm_core.o
--- /dev/null
+#include <linux/atmel_tc.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+/* Number of bytes to reserve for the iomem resource */
+#define ATMEL_TC_IOMEM_SIZE 256
+
+
+/*
+ * This is a thin library to solve the problem of how to portably allocate
+ * one of the TC blocks. For simplicity, it doesn't currently expect to
+ * share individual timers between different drivers.
+ */
+
+#if defined(CONFIG_AVR32)
+/* AVR32 has these divide PBB */
+const u8 atmel_tc_divisors[5] = { 0, 4, 8, 16, 32, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#elif defined(CONFIG_ARCH_AT91)
+/* AT91 has these divide MCK */
+const u8 atmel_tc_divisors[5] = { 2, 8, 32, 128, 0, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#endif
+
+static DEFINE_SPINLOCK(tc_list_lock);
+static LIST_HEAD(tc_list);
+
+/**
+ * atmel_tc_alloc - allocate a specified TC block
+ * @block: which block to allocate
+ * @name: name to be associated with the iomem resource
+ *
+ * Caller allocates a block. If it is available, a pointer to a
+ * pre-initialized struct atmel_tc is returned. The caller can access
+ * the registers directly through the "regs" field.
+ */
+struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name)
+{
+ struct atmel_tc *tc;
+ struct platform_device *pdev = NULL;
+ struct resource *r;
+
+ spin_lock(&tc_list_lock);
+ list_for_each_entry(tc, &tc_list, node) {
+ if (tc->pdev->id == block) {
+ pdev = tc->pdev;
+ break;
+ }
+ }
+
+ if (!pdev || tc->iomem)
+ goto fail;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ r = request_mem_region(r->start, ATMEL_TC_IOMEM_SIZE, name);
+ if (!r)
+ goto fail;
+
+ tc->regs = ioremap(r->start, ATMEL_TC_IOMEM_SIZE);
+ if (!tc->regs)
+ goto fail_ioremap;
+
+ tc->iomem = r;
+
+out:
+ spin_unlock(&tc_list_lock);
+ return tc;
+
+fail_ioremap:
+ release_resource(r);
+fail:
+ tc = NULL;
+ goto out;
+}
+EXPORT_SYMBOL_GPL(atmel_tc_alloc);
+
+/**
+ * atmel_tc_free - release a specified TC block
+ * @tc: Timer/counter block that was returned by atmel_tc_alloc()
+ *
+ * This reverses the effect of atmel_tc_alloc(), unmapping the I/O
+ * registers, invalidating the resource returned by that routine and
+ * making the TC available to other drivers.
+ */
+void atmel_tc_free(struct atmel_tc *tc)
+{
+ spin_lock(&tc_list_lock);
+ if (tc->regs) {
+ iounmap(tc->regs);
+ release_resource(tc->iomem);
+ tc->regs = NULL;
+ tc->iomem = NULL;
+ }
+ spin_unlock(&tc_list_lock);
+}
+EXPORT_SYMBOL_GPL(atmel_tc_free);
+
+static int __init tc_probe(struct platform_device *pdev)
+{
+ struct atmel_tc *tc;
+ struct clk *clk;
+ int irq;
+
+ if (!platform_get_resource(pdev, IORESOURCE_MEM, 0))
+ return -EINVAL;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -EINVAL;
+
+ tc = kzalloc(sizeof(struct atmel_tc), GFP_KERNEL);
+ if (!tc)
+ return -ENOMEM;
+
+ tc->pdev = pdev;
+
+ clk = clk_get(&pdev->dev, "t0_clk");
+ if (IS_ERR(clk)) {
+ kfree(tc);
+ return -EINVAL;
+ }
+
+ tc->clk[0] = clk;
+ tc->clk[1] = clk_get(&pdev->dev, "t1_clk");
+ if (IS_ERR(tc->clk[1]))
+ tc->clk[1] = clk;
+ tc->clk[2] = clk_get(&pdev->dev, "t2_clk");
+ if (IS_ERR(tc->clk[2]))
+ tc->clk[2] = clk;
+
+ tc->irq[0] = irq;
+ tc->irq[1] = platform_get_irq(pdev, 1);
+ if (tc->irq[1] < 0)
+ tc->irq[1] = irq;
+ tc->irq[2] = platform_get_irq(pdev, 2);
+ if (tc->irq[2] < 0)
+ tc->irq[2] = irq;
+
+ spin_lock(&tc_list_lock);
+ list_add_tail(&tc->node, &tc_list);
+ spin_unlock(&tc_list_lock);
+
+ return 0;
+}
+
+static struct platform_driver tc_driver = {
+ .driver.name = "atmel_tcb",
+};
+
+static int __init tc_init(void)
+{
+ return platform_driver_probe(&tc_driver, tc_probe);
+}
+arch_initcall(tc_init);
--- /dev/null
+/*
+ * Timer/Counter Unit (TC) registers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef ATMEL_TC_H
+#define ATMEL_TC_H
+
+#include <linux/compiler.h>
+#include <linux/list.h>
+
+/*
+ * Many 32-bit Atmel SOCs include one or more TC blocks, each of which holds
+ * three general-purpose 16-bit timers. These timers share one register bank.
+ * Depending on the SOC, each timer may have its own clock and IRQ, or those
+ * may be shared by the whole TC block.
+ *
+ * These TC blocks may have up to nine external pins: TCLK0..2 signals for
+ * clocks or clock gates, and per-timer TIOA and TIOB signals used for PWM
+ * or triggering. Those pins need to be set up for use with the TC block,
+ * else they will be used as GPIOs or for a different controller.
+ *
+ * Although we expect each TC block to have a platform_device node, those
+ * nodes are not what drivers bind to. Instead, they ask for a specific
+ * TC block, by number ... which is a common approach on systems with many
+ * timers. Then they use clk_get() and platform_get_irq() to get clock and
+ * IRQ resources.
+ */
+
+struct clk;
+
+/**
+ * struct atmel_tc - information about a Timer/Counter Block
+ * @pdev: physical device
+ * @iomem: resource associated with the I/O register
+ * @regs: mapping through which the I/O registers can be accessed
+ * @irq: irq for each of the three channels
+ * @clk: internal clock source for each of the three channels
+ * @node: list node, for tclib internal use
+ *
+ * On some platforms, each TC channel has its own clocks and IRQs,
+ * while on others, all TC channels share the same clock and IRQ.
+ * Drivers should clk_enable() all the clocks they need even though
+ * all the entries in @clk may point to the same physical clock.
+ * Likewise, drivers should request irqs independently for each
+ * channel, but they must use IRQF_SHARED in case some of the entries
+ * in @irq are actually the same IRQ.
+ */
+struct atmel_tc {
+ struct platform_device *pdev;
+ struct resource *iomem;
+ void __iomem *regs;
+ int irq[3];
+ struct clk *clk[3];
+ struct list_head node;
+};
+
+extern struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name);
+extern void atmel_tc_free(struct atmel_tc *tc);
+
+/* platform-specific ATMEL_TC_TIMER_CLOCKx divisors (0 means 32KiHz) */
+extern const u8 atmel_tc_divisors[5];
+
+
+/*
+ * Two registers have block-wide controls. These are: configuring the three
+ * "external" clocks (or event sources) used by the timer channels; and
+ * synchronizing the timers by resetting them all at once.
+ *
+ * "External" can mean "external to chip" using the TCLK0, TCLK1, or TCLK2
+ * signals. Or, it can mean "external to timer", using the TIOA output from
+ * one of the other two timers that's being run in waveform mode.
+ */
+
+#define ATMEL_TC_BCR 0xc0 /* TC Block Control Register */
+#define ATMEL_TC_SYNC (1 << 0) /* synchronize timers */
+
+#define ATMEL_TC_BMR 0xc4 /* TC Block Mode Register */
+#define ATMEL_TC_TC0XC0S (3 << 0) /* external clock 0 source */
+#define ATMEL_TC_TC0XC0S_TCLK0 (0 << 0)
+#define ATMEL_TC_TC0XC0S_NONE (1 << 0)
+#define ATMEL_TC_TC0XC0S_TIOA1 (2 << 0)
+#define ATMEL_TC_TC0XC0S_TIOA2 (3 << 0)
+#define ATMEL_TC_TC1XC1S (3 << 2) /* external clock 1 source */
+#define ATMEL_TC_TC1XC1S_TCLK1 (0 << 2)
+#define ATMEL_TC_TC1XC1S_NONE (1 << 2)
+#define ATMEL_TC_TC1XC1S_TIOA0 (2 << 2)
+#define ATMEL_TC_TC1XC1S_TIOA2 (3 << 2)
+#define ATMEL_TC_TC2XC2S (3 << 4) /* external clock 2 source */
+#define ATMEL_TC_TC2XC2S_TCLK2 (0 << 4)
+#define ATMEL_TC_TC2XC2S_NONE (1 << 4)
+#define ATMEL_TC_TC2XC2S_TIOA0 (2 << 4)
+#define ATMEL_TC_TC2XC2S_TIOA1 (3 << 4)
+
+
+/*
+ * Each TC block has three "channels", each with one counter and controls.
+ *
+ * Note that the semantics of ATMEL_TC_TIMER_CLOCKx (input clock selection
+ * when it's not "external") is silicon-specific. AT91 platforms use one
+ * set of definitions; AVR32 platforms use a different set. Don't hard-wire
+ * such knowledge into your code, use the global "atmel_tc_divisors" ...
+ * where index N is the divisor for clock N+1, else zero to indicate it uses
+ * the 32 KiHz clock.
+ *
+ * The timers can be chained in various ways, and operated in "waveform"
+ * generation mode (including PWM) or "capture" mode (to time events). In
+ * both modes, behavior can be configured in many ways.
+ *
+ * Each timer has two I/O pins, TIOA and TIOB. Waveform mode uses TIOA as a
+ * PWM output, and TIOB as either another PWM or as a trigger. Capture mode
+ * uses them only as inputs.
+ */
+#define ATMEL_TC_CHAN(idx) ((idx)*0x40)
+#define ATMEL_TC_REG(idx, reg) (ATMEL_TC_CHAN(idx) + ATMEL_TC_ ## reg)
+
+#define ATMEL_TC_CCR 0x00 /* Channel Control Register */
+#define ATMEL_TC_CLKEN (1 << 0) /* clock enable */
+#define ATMEL_TC_CLKDIS (1 << 1) /* clock disable */
+#define ATMEL_TC_SWTRG (1 << 2) /* software trigger */
+
+#define ATMEL_TC_CMR 0x04 /* Channel Mode Register */
+
+/* Both modes share some CMR bits */
+#define ATMEL_TC_TCCLKS (7 << 0) /* clock source */
+#define ATMEL_TC_TIMER_CLOCK1 (0 << 0)
+#define ATMEL_TC_TIMER_CLOCK2 (1 << 0)
+#define ATMEL_TC_TIMER_CLOCK3 (2 << 0)
+#define ATMEL_TC_TIMER_CLOCK4 (3 << 0)
+#define ATMEL_TC_TIMER_CLOCK5 (4 << 0)
+#define ATMEL_TC_XC0 (5 << 0)
+#define ATMEL_TC_XC1 (6 << 0)
+#define ATMEL_TC_XC2 (7 << 0)
+#define ATMEL_TC_CLKI (1 << 3) /* clock invert */
+#define ATMEL_TC_BURST (3 << 4) /* clock gating */
+#define ATMEL_TC_GATE_NONE (0 << 4)
+#define ATMEL_TC_GATE_XC0 (1 << 4)
+#define ATMEL_TC_GATE_XC1 (2 << 4)
+#define ATMEL_TC_GATE_XC2 (3 << 4)
+#define ATMEL_TC_WAVE (1 << 15) /* true = Waveform mode */
+
+/* CAPTURE mode CMR bits */
+#define ATMEL_TC_LDBSTOP (1 << 6) /* counter stops on RB load */
+#define ATMEL_TC_LDBDIS (1 << 7) /* counter disable on RB load */
+#define ATMEL_TC_ETRGEDG (3 << 8) /* external trigger edge */
+#define ATMEL_TC_ETRGEDG_NONE (0 << 8)
+#define ATMEL_TC_ETRGEDG_RISING (1 << 8)
+#define ATMEL_TC_ETRGEDG_FALLING (2 << 8)
+#define ATMEL_TC_ETRGEDG_BOTH (3 << 8)
+#define ATMEL_TC_ABETRG (1 << 10) /* external trigger is TIOA? */
+#define ATMEL_TC_CPCTRG (1 << 14) /* RC compare trigger enable */
+#define ATMEL_TC_LDRA (3 << 16) /* RA loading edge (of TIOA) */
+#define ATMEL_TC_LDRA_NONE (0 << 16)
+#define ATMEL_TC_LDRA_RISING (1 << 16)
+#define ATMEL_TC_LDRA_FALLING (2 << 16)
+#define ATMEL_TC_LDRA_BOTH (3 << 16)
+#define ATMEL_TC_LDRB (3 << 18) /* RB loading edge (of TIOA) */
+#define ATMEL_TC_LDRB_NONE (0 << 18)
+#define ATMEL_TC_LDRB_RISING (1 << 18)
+#define ATMEL_TC_LDRB_FALLING (2 << 18)
+#define ATMEL_TC_LDRB_BOTH (3 << 18)
+
+/* WAVEFORM mode CMR bits */
+#define ATMEL_TC_CPCSTOP (1 << 6) /* RC compare stops counter */
+#define ATMEL_TC_CPCDIS (1 << 7) /* RC compare disables counter */
+#define ATMEL_TC_EEVTEDG (3 << 8) /* external event edge */
+#define ATMEL_TC_EEVTEDG_NONE (0 << 8)
+#define ATMEL_TC_EEVTEDG_RISING (1 << 8)
+#define ATMEL_TC_EEVTEDG_FALLING (2 << 8)
+#define ATMEL_TC_EEVTEDG_BOTH (3 << 8)
+#define ATMEL_TC_EEVT (3 << 10) /* external event source */
+#define ATMEL_TC_EEVT_TIOB (0 << 10)
+#define ATMEL_TC_EEVT_XC0 (1 << 10)
+#define ATMEL_TC_EEVT_XC1 (2 << 10)
+#define ATMEL_TC_EEVT_XC2 (3 << 10)
+#define ATMEL_TC_ENETRG (1 << 12) /* external event is trigger */
+#define ATMEL_TC_WAVESEL (3 << 13) /* waveform type */
+#define ATMEL_TC_WAVESEL_UP (0 << 13)
+#define ATMEL_TC_WAVESEL_UPDOWN (1 << 13)
+#define ATMEL_TC_WAVESEL_UP_AUTO (2 << 13)
+#define ATMEL_TC_WAVESEL_UPDOWN_AUTO (3 << 13)
+#define ATMEL_TC_ACPA (3 << 16) /* RA compare changes TIOA */
+#define ATMEL_TC_ACPA_NONE (0 << 16)
+#define ATMEL_TC_ACPA_SET (1 << 16)
+#define ATMEL_TC_ACPA_CLEAR (2 << 16)
+#define ATMEL_TC_ACPA_TOGGLE (3 << 16)
+#define ATMEL_TC_ACPC (3 << 18) /* RC compare changes TIOA */
+#define ATMEL_TC_ACPC_NONE (0 << 18)
+#define ATMEL_TC_ACPC_SET (1 << 18)
+#define ATMEL_TC_ACPC_CLEAR (2 << 18)
+#define ATMEL_TC_ACPC_TOGGLE (3 << 18)
+#define ATMEL_TC_AEEVT (3 << 20) /* external event changes TIOA */
+#define ATMEL_TC_AEEVT_NONE (0 << 20)
+#define ATMEL_TC_AEEVT_SET (1 << 20)
+#define ATMEL_TC_AEEVT_CLEAR (2 << 20)
+#define ATMEL_TC_AEEVT_TOGGLE (3 << 20)
+#define ATMEL_TC_ASWTRG (3 << 22) /* software trigger changes TIOA */
+#define ATMEL_TC_ASWTRG_NONE (0 << 22)
+#define ATMEL_TC_ASWTRG_SET (1 << 22)
+#define ATMEL_TC_ASWTRG_CLEAR (2 << 22)
+#define ATMEL_TC_ASWTRG_TOGGLE (3 << 22)
+#define ATMEL_TC_BCPB (3 << 24) /* RB compare changes TIOB */
+#define ATMEL_TC_BCPB_NONE (0 << 24)
+#define ATMEL_TC_BCPB_SET (1 << 24)
+#define ATMEL_TC_BCPB_CLEAR (2 << 24)
+#define ATMEL_TC_BCPB_TOGGLE (3 << 24)
+#define ATMEL_TC_BCPC (3 << 26) /* RC compare changes TIOB */
+#define ATMEL_TC_BCPC_NONE (0 << 26)
+#define ATMEL_TC_BCPC_SET (1 << 26)
+#define ATMEL_TC_BCPC_CLEAR (2 << 26)
+#define ATMEL_TC_BCPC_TOGGLE (3 << 26)
+#define ATMEL_TC_BEEVT (3 << 28) /* external event changes TIOB */
+#define ATMEL_TC_BEEVT_NONE (0 << 28)
+#define ATMEL_TC_BEEVT_SET (1 << 28)
+#define ATMEL_TC_BEEVT_CLEAR (2 << 28)
+#define ATMEL_TC_BEEVT_TOGGLE (3 << 28)
+#define ATMEL_TC_BSWTRG (3 << 30) /* software trigger changes TIOB */
+#define ATMEL_TC_BSWTRG_NONE (0 << 30)
+#define ATMEL_TC_BSWTRG_SET (1 << 30)
+#define ATMEL_TC_BSWTRG_CLEAR (2 << 30)
+#define ATMEL_TC_BSWTRG_TOGGLE (3 << 30)
+
+#define ATMEL_TC_CV 0x10 /* counter Value */
+#define ATMEL_TC_RA 0x14 /* register A */
+#define ATMEL_TC_RB 0x18 /* register B */
+#define ATMEL_TC_RC 0x1c /* register C */
+
+#define ATMEL_TC_SR 0x20 /* status (read-only) */
+/* Status-only flags */
+#define ATMEL_TC_CLKSTA (1 << 16) /* clock enabled */
+#define ATMEL_TC_MTIOA (1 << 17) /* TIOA mirror */
+#define ATMEL_TC_MTIOB (1 << 18) /* TIOB mirror */
+
+#define ATMEL_TC_IER 0x24 /* interrupt enable (write-only) */
+#define ATMEL_TC_IDR 0x28 /* interrupt disable (write-only) */
+#define ATMEL_TC_IMR 0x2c /* interrupt mask (read-only) */
+
+/* Status and IRQ flags */
+#define ATMEL_TC_COVFS (1 << 0) /* counter overflow */
+#define ATMEL_TC_LOVRS (1 << 1) /* load overrun */
+#define ATMEL_TC_CPAS (1 << 2) /* RA compare */
+#define ATMEL_TC_CPBS (1 << 3) /* RB compare */
+#define ATMEL_TC_CPCS (1 << 4) /* RC compare */
+#define ATMEL_TC_LDRAS (1 << 5) /* RA loading */
+#define ATMEL_TC_LDRBS (1 << 6) /* RB loading */
+#define ATMEL_TC_ETRGS (1 << 7) /* external trigger */
+
+#endif
projects / linux-2.6-omap-h63xx.git / commitdiff