summary |
shortlog |
log |
commit | commitdiff |
tree
raw |
patch |
inline | side by side (from parent 1:
8263e5b)
Clock rate change code executes inside a spinlock with hardirqs
disabled. The only code that should be messing around with the
hardirq state should be the plat-omap/clock.c code. In the
omap2_reprogram_dpllcore() case, this probably just wastes cycles, but
in the omap3_core_dpll_m2_set_rate() case, this is a nasty bug.
linux-omap source commit is
b9b6208dadb5e0d8b290900a3ffa911673ca97ed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
u32 bypass = 0;
struct prcm_config tmpset;
const struct dpll_data *dd;
u32 bypass = 0;
struct prcm_config tmpset;
const struct dpll_data *dd;
- unsigned long flags;
- int ret = -EINVAL;
cur_rate = omap2_get_dpll_rate_24xx(&dpll_ck);
mult = cm_read_mod_reg(PLL_MOD, CM_CLKSEL2);
mult &= OMAP24XX_CORE_CLK_SRC_MASK;
cur_rate = omap2_get_dpll_rate_24xx(&dpll_ck);
mult = cm_read_mod_reg(PLL_MOD, CM_CLKSEL2);
mult &= OMAP24XX_CORE_CLK_SRC_MASK;
} else if (rate != cur_rate) {
valid_rate = omap2_dpllcore_round_rate(rate);
if (valid_rate != rate)
} else if (rate != cur_rate) {
valid_rate = omap2_dpllcore_round_rate(rate);
if (valid_rate != rate)
if (mult == 1)
low = curr_prcm_set->dpll_speed;
if (mult == 1)
low = curr_prcm_set->dpll_speed;
dd = clk->dpll_data;
if (!dd)
dd = clk->dpll_data;
if (!dd)
tmpset.cm_clksel1_pll = __raw_readl(dd->mult_div1_reg);
tmpset.cm_clksel1_pll &= ~(dd->mult_mask |
tmpset.cm_clksel1_pll = __raw_readl(dd->mult_div1_reg);
tmpset.cm_clksel1_pll &= ~(dd->mult_mask |
omap2xxx_sdrc_init_params(omap2xxx_sdrc_dll_is_unlocked());
omap2xxx_sdrc_reprogram(done_rate, 0);
}
omap2xxx_sdrc_init_params(omap2xxx_sdrc_dll_is_unlocked());
omap2xxx_sdrc_reprogram(done_rate, 0);
}
-dpll_exit:
- local_irq_restore(flags);
- return(ret);
WARN_ON(new_div != 1 && new_div != 2);
/* REVISIT: Add SDRC_MR changing to this code also */
WARN_ON(new_div != 1 && new_div != 2);
/* REVISIT: Add SDRC_MR changing to this code also */
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
sp->actim_ctrlb, new_div);
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
sp->actim_ctrlb, new_div);