in drivers/net/eexpress.c:558, function unstick_cu()
while (!SCB_complete(rsst=scb_status(dev))) {
...
if (...)
printk(KERN_WARNING "%s: Reset timed out status %04x, retrying...\n",
dev->name,rsst);
}
but this will become
while (!((rsst = scb_status(dev) & 0x8000) != 0) ...
because of the macro:
#define SCB_complete(s) ((s&0x8000)!=0)
so rsst can only become either 0x8000 or 0, but in the latter case the
loop ends, I think the wrong timed out status is printed. This also
cleans up similar macros.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*/
/* these functions take the SCB status word and test the relevant status bit */
*/
/* these functions take the SCB status word and test the relevant status bit */
-#define SCB_complete(s) ((s&0x8000)!=0)
-#define SCB_rxdframe(s) ((s&0x4000)!=0)
-#define SCB_CUdead(s) ((s&0x2000)!=0)
-#define SCB_RUdead(s) ((s&0x1000)!=0)
-#define SCB_ack(s) (s & 0xf000)
+#define SCB_complete(s) (((s) & 0x8000) != 0)
+#define SCB_rxdframe(s) (((s) & 0x4000) != 0)
+#define SCB_CUdead(s) (((s) & 0x2000) != 0)
+#define SCB_RUdead(s) (((s) & 0x1000) != 0)
+#define SCB_ack(s) ((s) & 0xf000)
/* Command unit status: 0=idle, 1=suspended, 2=active */
/* Command unit status: 0=idle, 1=suspended, 2=active */
-#define SCB_CUstat(s) ((s&0x0300)>>8)
+#define SCB_CUstat(s) (((s)&0x0300)>>8)
/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
-#define SCB_RUstat(s) ((s&0x0070)>>4)
+#define SCB_RUstat(s) (((s)&0x0070)>>4)
/* SCB commands */
#define SCB_CUnop 0x0000
/* SCB commands */
#define SCB_CUnop 0x0000
* Command block defines
*/
* Command block defines
*/
-#define Stat_Done(s) ((s&0x8000)!=0)
-#define Stat_Busy(s) ((s&0x4000)!=0)
-#define Stat_OK(s) ((s&0x2000)!=0)
-#define Stat_Abort(s) ((s&0x1000)!=0)
-#define Stat_STFail ((s&0x0800)!=0)
-#define Stat_TNoCar(s) ((s&0x0400)!=0)
-#define Stat_TNoCTS(s) ((s&0x0200)!=0)
-#define Stat_TNoDMA(s) ((s&0x0100)!=0)
-#define Stat_TDefer(s) ((s&0x0080)!=0)
-#define Stat_TColl(s) ((s&0x0040)!=0)
-#define Stat_TXColl(s) ((s&0x0020)!=0)
-#define Stat_NoColl(s) (s&0x000f)
+#define Stat_Done(s) (((s) & 0x8000) != 0)
+#define Stat_Busy(s) (((s) & 0x4000) != 0)
+#define Stat_OK(s) (((s) & 0x2000) != 0)
+#define Stat_Abort(s) (((s) & 0x1000) != 0)
+#define Stat_STFail (((s) & 0x0800) != 0)
+#define Stat_TNoCar(s) (((s) & 0x0400) != 0)
+#define Stat_TNoCTS(s) (((s) & 0x0200) != 0)
+#define Stat_TNoDMA(s) (((s) & 0x0100) != 0)
+#define Stat_TDefer(s) (((s) & 0x0080) != 0)
+#define Stat_TColl(s) (((s) & 0x0040) != 0)
+#define Stat_TXColl(s) (((s) & 0x0020) != 0)
+#define Stat_NoColl(s) ((s) & 0x000f)
/* Cmd_END will end AFTER the command if this is the first
* command block after an SCB_CUstart, but BEFORE the command
/* Cmd_END will end AFTER the command if this is the first
* command block after an SCB_CUstart, but BEFORE the command
* Frame Descriptor (Receive block) defines
*/
* Frame Descriptor (Receive block) defines
*/
-#define FD_Done(s) ((s&0x8000)!=0)
-#define FD_Busy(s) ((s&0x4000)!=0)
-#define FD_OK(s) ((s&0x2000)!=0)
+#define FD_Done(s) (((s) & 0x8000) != 0)
+#define FD_Busy(s) (((s) & 0x4000) != 0)
+#define FD_OK(s) (((s) & 0x2000) != 0)
-#define FD_CRC(s) ((s&0x0800)!=0)
-#define FD_Align(s) ((s&0x0400)!=0)
-#define FD_Resrc(s) ((s&0x0200)!=0)
-#define FD_DMA(s) ((s&0x0100)!=0)
-#define FD_Short(s) ((s&0x0080)!=0)
-#define FD_NoEOF(s) ((s&0x0040)!=0)
+#define FD_CRC(s) (((s) & 0x0800) != 0)
+#define FD_Align(s) (((s) & 0x0400) != 0)
+#define FD_Resrc(s) (((s) & 0x0200) != 0)
+#define FD_DMA(s) (((s) & 0x0100) != 0)
+#define FD_Short(s) (((s) & 0x0080) != 0)
+#define FD_NoEOF(s) (((s) & 0x0040) != 0)
struct rfd_header {
volatile unsigned long flags;
struct rfd_header {
volatile unsigned long flags;