+/*
+ * Read and write single 8-bit registers
+ */
+int twl4030_i2c_write_u8(u8 mod_no, u8 val, u8 reg);
+int twl4030_i2c_read_u8(u8 mod_no, u8 *val, u8 reg);
+
+/*
+ * Read and write several 8-bit registers at once.
+ *
+ * IMPORTANT: For twl4030_i2c_write(), allocate num_bytes + 1
+ * for the value, and populate your data starting at offset 1.
+ */
+int twl4030_i2c_write(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
+int twl4030_i2c_read(u8 mod_no, u8 *value, u8 reg, u8 num_bytes);
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE: at up to 1024 registers, this is a big chip.
+ *
+ * Avoid putting register declarations in this file, instead of into
+ * a driver-private file, unless some of the registers in a block
+ * need to be shared with other drivers. One example is blocks that
+ * have Secondary IRQ Handler (SIH) registers.
+ */
+
+#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
+#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
+#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
+ */
+
+#define REG_GPIODATAIN1 0x0
+#define REG_GPIODATAIN2 0x1
+#define REG_GPIODATAIN3 0x2
+#define REG_GPIODATADIR1 0x3
+#define REG_GPIODATADIR2 0x4
+#define REG_GPIODATADIR3 0x5
+#define REG_GPIODATAOUT1 0x6
+#define REG_GPIODATAOUT2 0x7
+#define REG_GPIODATAOUT3 0x8
+#define REG_CLEARGPIODATAOUT1 0x9
+#define REG_CLEARGPIODATAOUT2 0xA
+#define REG_CLEARGPIODATAOUT3 0xB
+#define REG_SETGPIODATAOUT1 0xC
+#define REG_SETGPIODATAOUT2 0xD
+#define REG_SETGPIODATAOUT3 0xE
+#define REG_GPIO_DEBEN1 0xF
+#define REG_GPIO_DEBEN2 0x10
+#define REG_GPIO_DEBEN3 0x11
+#define REG_GPIO_CTRL 0x12
+#define REG_GPIOPUPDCTR1 0x13
+#define REG_GPIOPUPDCTR2 0x14
+#define REG_GPIOPUPDCTR3 0x15
+#define REG_GPIOPUPDCTR4 0x16
+#define REG_GPIOPUPDCTR5 0x17
+#define REG_GPIO_ISR1A 0x19
+#define REG_GPIO_ISR2A 0x1A
+#define REG_GPIO_ISR3A 0x1B
+#define REG_GPIO_IMR1A 0x1C
+#define REG_GPIO_IMR2A 0x1D
+#define REG_GPIO_IMR3A 0x1E
+#define REG_GPIO_ISR1B 0x1F
+#define REG_GPIO_ISR2B 0x20
+#define REG_GPIO_ISR3B 0x21
+#define REG_GPIO_IMR1B 0x22
+#define REG_GPIO_IMR2B 0x23
+#define REG_GPIO_IMR3B 0x24
+#define REG_GPIO_EDR1 0x28
+#define REG_GPIO_EDR2 0x29
+#define REG_GPIO_EDR3 0x2A
+#define REG_GPIO_EDR4 0x2B
+#define REG_GPIO_EDR5 0x2C
+#define REG_GPIO_SIH_CTRL 0x2D
+
+/* Up to 18 signals are available as GPIOs, when their
+ * pins are not assigned to another use (such as ULPI/USB).
+ */
+#define TWL4030_GPIO_MAX 18
+
+/*----------------------------------------------------------------------*/
+