X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=drivers%2Fide%2FKconfig;h=6d7401772a8f6d7530a89331a16cace5528b4623;hb=28502848f52f12fcebbdec663103db2dd0740122;hp=74a369a6116fc7fbeb7bea0c68c629ec4cfb1102;hpb=c472273f863c80b87e53356256c5466df24328f0;p=linux-2.6-omap-h63xx.git diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index 74a369a6116..6d7401772a8 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -84,21 +84,40 @@ config BLK_DEV_IDE_SATA If unsure, say N. -config BLK_DEV_IDEDISK - tristate "Include IDE/ATA-2 DISK support" - ---help--- - This will include enhanced support for MFM/RLL/IDE hard disks. If - you have a MFM/RLL/IDE disk, and there is no special reason to use - the old hard disk driver instead, say Y. If you have an SCSI-only - system, you can say N here. +config IDE_GD + tristate "generic ATA/ATAPI disk support" + default y + help + Support for ATA/ATAPI disks (including ATAPI floppy drives). - To compile this driver as a module, choose M here: the - module will be called ide-disk. - Do not compile this driver as a module if your root file system - (the one containing the directory /) is located on the IDE disk. + To compile this driver as a module, choose M here. + The module will be called ide-gd_mod. + + If unsure, say Y. + +config IDE_GD_ATA + bool "ATA disk support" + depends on IDE_GD + default y + help + This will include support for ATA hard disks. If unsure, say Y. +config IDE_GD_ATAPI + bool "ATAPI floppy support" + depends on IDE_GD + select IDE_ATAPI + help + This will include support for ATAPI floppy drives + (i.e. Iomega ZIP or MKE LS-120). + + For information about jumper settings and the question + of when a ZIP drive uses a partition table, see + . + + If unsure, say N. + config BLK_DEV_IDECS tristate "PCMCIA IDE support" depends on PCMCIA @@ -163,29 +182,6 @@ config BLK_DEV_IDETAPE To compile this driver as a module, choose M here: the module will be called ide-tape. -config BLK_DEV_IDEFLOPPY - tristate "Include IDE/ATAPI FLOPPY support" - select IDE_ATAPI - ---help--- - If you have an IDE floppy drive which uses the ATAPI protocol, - answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy - drives, similar to the SCSI protocol. - - The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by - this driver. For information about jumper settings and the question - of when a ZIP drive uses a partition table, see - . - (ATAPI PD-CD/CDR drives are not supported by this driver; support - for PD-CD/CDR drives is available if you answer Y to - "SCSI emulation support", below). - - If you say Y here, the FLOPPY drive will be identified along with - other IDE devices, as "hdb" or "hdc", or something similar (check - the boot messages with dmesg). - - To compile this driver as a module, choose M here: the - module will be called ide-floppy. - config BLK_DEV_IDESCSI tristate "SCSI emulation support (DEPRECATED)" depends on SCSI @@ -332,7 +328,7 @@ config IDEPCI_PCIBUS_ORDER # TODO: split it on per host driver config options (or module parameters) config BLK_DEV_OFFBOARD bool "Boot off-board chipsets first support (DEPRECATED)" - depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001) + depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001) help Normally, IDE controllers built into the motherboard (on-board controllers) are assigned to ide0 and ide1 while those on add-in PCI @@ -482,28 +478,6 @@ config BLK_DEV_CS5535 It is safe to say Y to this question. -config BLK_DEV_HPT34X - tristate "HPT34X chipset support" - depends on BROKEN - select BLK_DEV_IDEDMA_PCI - help - This driver adds up to 4 more EIDE devices sharing a single - interrupt. The HPT343 chipset in its current form is a non-bootable - controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX) - PCI UDMA controllers. This driver requires dynamic tuning of the - chipset during the ide-probe at boot time. It is reported to support - DVD II drives, by the manufacturer. - -config HPT34X_AUTODMA - bool "HPT34X AUTODMA support (EXPERIMENTAL)" - depends on BLK_DEV_HPT34X && EXPERIMENTAL - help - This is a dangerous thing to attempt currently! Please read the - comments at the top of . If you say Y - here, then say Y to "Use DMA by default when available" as well. - - If unsure, say N. - config BLK_DEV_HPT366 tristate "HPT36X/37X chipset support" select BLK_DEV_IDEDMA_PCI @@ -746,6 +720,16 @@ config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ default "128" depends on BLK_DEV_IDE_AU1XXX +config BLK_DEV_IDE_TX4938 + tristate "TX4938 internal IDE support" + depends on SOC_TX4938 + select IDE_TIMINGS + +config BLK_DEV_IDE_TX4939 + tristate "TX4939 internal IDE support" + depends on SOC_TX4939 + select BLK_DEV_IDEDMA_SFF + config IDE_ARM tristate "ARM IDE support" depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)