X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=d1b87d26942ff3373507c4c483fa476b5d36dc16;hb=478c6a43fcbc6c11609f8cee7c7b57223907754f;hp=7068d0bc47c5cd80c4ccc6b963ac81fa59e8be5e;hpb=8a3f257c704e02aee9869decd069a806b45be3f1;p=linux-2.6-omap-h63xx.git diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 7068d0bc47c..d1b87d26942 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -44,6 +44,7 @@ parameter is applicable: FB The frame buffer device is enabled. HW Appropriate hardware is enabled. IA-64 IA-64 architecture is enabled. + IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. ISAPNP ISA PnP code is enabled. @@ -507,11 +508,23 @@ and is between 256 and 4096 characters. It is defined in the file Range: 0 - 8192 Default: 64 + dma_debug=off If the kernel is compiled with DMA_API_DEBUG support + this option disables the debugging code at boot. + + dma_debug_entries= + This option allows to tune the number of preallocated + entries for DMA-API debugging code. One entry is + required per DMA-API allocation. Use this if the + DMA-API debugging code disables itself because the + architectural default is too low. + hpet= [X86-32,HPET] option to control HPET usage - Format: { enable (default) | disable | force } + Format: { enable (default) | disable | force | + verbose } disable: disable HPET and use PIT instead force: allow force enabled of undocumented chips (ICH4, VIA, nVidia) + verbose: show contents of HPET registers during setup com20020= [HW,NET] ARCnet - COM20020 chipset Format: @@ -845,6 +858,15 @@ and is between 256 and 4096 characters. It is defined in the file hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC) terminal devices. Valid values: 0..8 + hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs. + If specified, z/VM IUCV HVC accepts connections + from listed z/VM user IDs only. + + i2c_bus= [HW] Override the default board specific I2C bus speed + or register an additional I2C bus that is not + registered from board initialization code. + Format: + , i8042.debug [HW] Toggle i8042 debug mode i8042.direct [HW] Put keyboard port into non-translated mode @@ -918,6 +940,15 @@ and is between 256 and 4096 characters. It is defined in the file ihash_entries= [KNL] Set number of hash buckets for inode cache. + ima_audit= [IMA] + Format: { "0" | "1" } + 0 -- integrity auditing messages. (Default) + 1 -- enable informational integrity auditing messages. + + ima_hash= [IMA] + Formt: { "sha1" | "md5" } + default: "sha1" + in2000= [HW,SCSI] See header of drivers/scsi/in2000.c. @@ -1326,8 +1357,13 @@ and is between 256 and 4096 characters. It is defined in the file memtest= [KNL,X86] Enable memtest Format: - range: 0,4 : pattern number default : 0 + Specifies the number of memtest passes to be + performed. Each pass selects another test + pattern from a given set of patterns. Memtest + fills the memory with this pattern, validates + memory contents and reserves bad memory + regions that are detected. meye.*= [HW] Set MotionEye Camera parameters See Documentation/video4linux/meye.txt. @@ -1503,7 +1539,9 @@ and is between 256 and 4096 characters. It is defined in the file noclflush [BUGS=X86] Don't use the CLFLUSH instruction - nohlt [BUGS=ARM,SH] + nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or + wfi(ARM) instruction doesn't work correctly and not to + use it. This is also useful when using JTAG debugger. no-hlt [BUGS=X86-32] Tells the kernel that the hlt instruction doesn't work correctly and not to @@ -1583,7 +1621,7 @@ and is between 256 and 4096 characters. It is defined in the file nosoftlockup [KNL] Disable the soft-lockup detector. noswapaccount [KNL] Disable accounting of swap in memory resource - controller. (See Documentation/controllers/memory.txt) + controller. (See Documentation/cgroups/memory.txt) nosync [HW,M68K] Disables sync negotiation for all devices. @@ -1675,6 +1713,8 @@ and is between 256 and 4096 characters. It is defined in the file See also Documentation/blockdev/paride.txt. pci=option[,option...] [PCI] various PCI subsystem options: + earlydump [X86] dump PCI config space before the kernel + changes anything off [X86] don't probe for the PCI bus bios [X86-32] force use of PCI BIOS, don't access the hardware directly. Use this if your machine @@ -1774,6 +1814,15 @@ and is between 256 and 4096 characters. It is defined in the file cbmemsize=nn[KMG] The fixed amount of bus space which is reserved for the CardBus bridge's memory window. The default value is 64 megabytes. + resource_alignment= + Format: + [@][:]:.[; ...] + Specifies alignment and device to reassign + aligned memory resources. + If is not specified, + PAGE_SIZE is used as alignment. + PCI-PCI bridge can be specified, if resource + windows need to be expanded. pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power Management. @@ -1832,11 +1881,6 @@ and is between 256 and 4096 characters. It is defined in the file autoconfiguration. Ranges are in pairs (memory base and size). - dynamic_printk Enables pr_debug()/dev_dbg() calls if - CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. - These can also be switched on/off via - /dynamic_printk/modules - print-fatal-signals= [KNL] debug: print fatal signals print-fatal-signals=1: print segfault info to @@ -1927,7 +1971,7 @@ and is between 256 and 4096 characters. It is defined in the file relax_domain_level= [KNL, SMP] Set scheduler's default relax_domain_level. - See Documentation/cpusets.txt. + See Documentation/cgroups/cpusets.txt. reserve= [KNL,BUGS] Force the kernel to ignore some iomem area @@ -2025,15 +2069,6 @@ and is between 256 and 4096 characters. It is defined in the file If enabled at boot time, /selinux/disable can be used later to disable prior to initial policy load. - selinux_compat_net = - [SELINUX] Set initial selinux_compat_net flag value. - Format: { "0" | "1" } - 0 -- use new secmark-based packet controls - 1 -- use legacy packet controls - Default value is 0 (preferred). - Value can be changed at runtime via - /selinux/compat_net. - serialnumber [BUGS=X86-32] shapers= [NET]