X-Git-Url: http://www.pilppa.org/gitweb/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=6dda1cc3fbafe6b43f4adb914537bc597d72b390;hb=ed40d0c472b136682b2fcba05f89762859c7374f;hp=ef9827f7c84efffbf5f2c8ef1ef4f01720287b48;hpb=9e495834e59ca9b29f1a1f63b9f5533bb022ac49;p=linux-2.6-omap-h63xx.git

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index ef9827f7c84..6dda1cc3fba 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -44,6 +44,7 @@ parameter is applicable:
 	FB	The frame buffer device is enabled.
 	HW	Appropriate hardware is enabled.
 	IA-64	IA-64 architecture is enabled.
+	IMA     Integrity measurement architecture is enabled.
 	IOSCHED	More than one I/O scheduler is enabled.
 	IP_PNP	IP DHCP, BOOTP, or RARP is enabled.
 	ISAPNP	ISA PnP code is enabled.
@@ -492,10 +493,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			Default: 64
 
 	hpet=		[X86-32,HPET] option to control HPET usage
-			Format: { enable (default) | disable | force }
+			Format: { enable (default) | disable | force |
+				verbose }
 			disable: disable HPET and use PIT instead
 			force: allow force enabled of undocumented chips (ICH4,
 			VIA, nVidia)
+			verbose: show contents of HPET registers during setup
 
 	com20020=	[HW,NET] ARCnet - COM20020 chipset
 			Format:
@@ -829,6 +832,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	hvc_iucv=	[S390] Number of z/VM IUCV hypervisor console (HVC)
 			       terminal devices. Valid values: 0..8
+	hvc_iucv_allow=	[S390] Comma-separated list of z/VM user IDs.
+			       If specified, z/VM IUCV HVC accepts connections
+			       from listed z/VM user IDs only.
 
 	i2c_bus=	[HW] Override the default board specific I2C bus speed
 			     or register an additional I2C bus that is not
@@ -908,6 +914,15 @@ and is between 256 and 4096 characters. It is defined in the file
 	ihash_entries=	[KNL]
 			Set number of hash buckets for inode cache.
 
+	ima_audit=	[IMA]
+			Format: { "0" | "1" }
+			0 -- integrity auditing messages. (Default)
+			1 -- enable informational integrity auditing messages.
+
+	ima_hash=	[IMA]
+			Formt: { "sha1" | "md5" }
+			default: "sha1"
+
 	in2000=		[HW,SCSI]
 			See header of drivers/scsi/in2000.c.
 
@@ -1822,11 +1837,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			autoconfiguration.
 			Ranges are in pairs (memory base and size).
 
-	dynamic_printk	Enables pr_debug()/dev_dbg() calls if
-			CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
-			These can also be switched on/off via
-			<debugfs>/dynamic_printk/modules
-
 	print-fatal-signals=
 			[KNL] debug: print fatal signals
 			print-fatal-signals=1: print segfault info to