u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
};
+/**
+ * enum ieee80211_max_queues - maximum number of queues
+ *
+ * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
+ * @IEEE80211_MAX_AMPDU_QUEUES: Maximum number of queues usable
+ * for A-MPDU operation.
+ */
+enum ieee80211_max_queues {
+ IEEE80211_MAX_QUEUES = 16,
+ IEEE80211_MAX_AMPDU_QUEUES = 16,
+};
+
/**
* struct ieee80211_tx_queue_params - transmit queue configuration
*
};
/**
- * struct ieee80211_tx_queue_stats_data - transmit queue statistics
+ * struct ieee80211_tx_queue_stats - transmit queue statistics
*
* @len: number of packets in queue
* @limit: queue length limit
* @count: number of frames sent
*/
-struct ieee80211_tx_queue_stats_data {
+struct ieee80211_tx_queue_stats {
unsigned int len;
unsigned int limit;
unsigned int count;
};
-/**
- * enum ieee80211_tx_queue - transmit queue number
- *
- * These constants are used with some callbacks that take a
- * queue number to set parameters for a queue.
- *
- * @IEEE80211_TX_QUEUE_DATA0: data queue 0
- * @IEEE80211_TX_QUEUE_DATA1: data queue 1
- * @IEEE80211_TX_QUEUE_DATA2: data queue 2
- * @IEEE80211_TX_QUEUE_DATA3: data queue 3
- * @IEEE80211_TX_QUEUE_DATA4: data queue 4
- * @IEEE80211_TX_QUEUE_SVP: ??
- * @NUM_TX_DATA_QUEUES: number of data queues
- * @IEEE80211_TX_QUEUE_AFTER_BEACON: transmit queue for frames to be
- * sent after a beacon
- * @IEEE80211_TX_QUEUE_BEACON: transmit queue for beacon frames
- * @NUM_TX_DATA_QUEUES_AMPDU: adding more queues for A-MPDU
- */
-enum ieee80211_tx_queue {
- IEEE80211_TX_QUEUE_DATA0,
- IEEE80211_TX_QUEUE_DATA1,
- IEEE80211_TX_QUEUE_DATA2,
- IEEE80211_TX_QUEUE_DATA3,
- IEEE80211_TX_QUEUE_DATA4,
- IEEE80211_TX_QUEUE_SVP,
-
- NUM_TX_DATA_QUEUES,
-
-/* due to stupidity in the sub-ioctl userspace interface, the items in
- * this struct need to have fixed values. As soon as it is removed, we can
- * fix these entries. */
- IEEE80211_TX_QUEUE_AFTER_BEACON = 6,
- IEEE80211_TX_QUEUE_BEACON = 7,
- NUM_TX_DATA_QUEUES_AMPDU = 16
-};
-
-struct ieee80211_tx_queue_stats {
- struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES_AMPDU];
-};
-
struct ieee80211_low_level_stats {
unsigned int dot11ACKFailureCount;
unsigned int dot11RTSFailureCount;
};
/**
- * enum mac80211_tx_control_flags - flags to describe Tx configuration for
- * the Tx frame
- *
- * These flags are used with the @flags member of &ieee80211_tx_control
- *
- * @IEEE80211_TXCTL_REQ_TX_STATUS: request TX status callback for this frame.
- * @IEEE80211_TXCTL_DO_NOT_ENCRYPT: send this frame without encryption;
- * e.g., for EAPOL frame
- * @IEEE80211_TXCTL_USE_RTS_CTS: use RTS-CTS before sending frame
- * @IEEE80211_TXCTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
- * for combined 802.11g / 802.11b networks)
- * @IEEE80211_TXCTL_NO_ACK: tell the low level not to wait for an ack
- * @IEEE80211_TXCTL_RATE_CTRL_PROBE
- * @EEE80211_TXCTL_CLEAR_PS_FILT: clear powersave filter
- * for destination station
- * @IEEE80211_TXCTL_REQUEUE:
- * @IEEE80211_TXCTL_FIRST_FRAGMENT: this is a first fragment of the frame
- * @IEEE80211_TXCTL_LONG_RETRY_LIMIT: this frame should be send using the
- * through set_retry_limit configured long
- * retry value
- * @IEEE80211_TXCTL_EAPOL_FRAME: internal to mac80211
- * @IEEE80211_TXCTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
- * @IEEE80211_TXCTL_AMPDU: this frame should be sent as part of an A-MPDU
- * @IEEE80211_TXCTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
- * of streams when this flag is on can be extracted
- * from antenna_sel_tx, so if 1 antenna is marked
- * use SISO, 2 antennas marked use MIMO, n antennas
- * marked use MIMO_n.
- * @IEEE80211_TXCTL_GREEN_FIELD: use green field protection for this frame
- * @IEEE80211_TXCTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width
- * @IEEE80211_TXCTL_DUP_DATA: duplicate data frame on both 20 Mhz channels
- * @IEEE80211_TXCTL_SHORT_GI: send this frame using short guard interval
+ * enum mac80211_tx_flags - flags to transmission information/status
+ *
+ * These flags are used with the @flags member of &ieee80211_tx_info
+ *
+ * @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
+ * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption;
+ * e.g., for EAPOL frame
+ * @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame
+ * @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
+ * for combined 802.11g / 802.11b networks)
+ * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
+ * @IEEE80211_TX_CTL_RATE_CTRL_PROBE
+ * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
+ * station
+ * @IEEE80211_TX_CTL_REQUEUE:
+ * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
+ * @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
+ * through set_retry_limit configured long retry value
+ * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211
+ * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
+ * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
+ * @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number
+ * of streams when this flag is on can be extracted from antenna_sel_tx,
+ * so if 1 antenna is marked use SISO, 2 antennas marked use MIMO, n
+ * antennas marked use MIMO_n.
+ * @IEEE80211_TX_CTL_GREEN_FIELD: use green field protection for this frame
+ * @IEEE80211_TX_CTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width
+ * @IEEE80211_TX_CTL_DUP_DATA: duplicate data frame on both 20 Mhz channels
+ * @IEEE80211_TX_CTL_SHORT_GI: send this frame using short guard interval
+ * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
+ * because the destination STA was in powersave mode.
+ * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
+ * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
+ * is for the whole aggregation.
*/
enum mac80211_tx_control_flags {
- IEEE80211_TXCTL_REQ_TX_STATUS = (1<<0),
- IEEE80211_TXCTL_DO_NOT_ENCRYPT = (1<<1),
- IEEE80211_TXCTL_USE_RTS_CTS = (1<<2),
- IEEE80211_TXCTL_USE_CTS_PROTECT = (1<<3),
- IEEE80211_TXCTL_NO_ACK = (1<<4),
- IEEE80211_TXCTL_RATE_CTRL_PROBE = (1<<5),
- IEEE80211_TXCTL_CLEAR_PS_FILT = (1<<6),
- IEEE80211_TXCTL_REQUEUE = (1<<7),
- IEEE80211_TXCTL_FIRST_FRAGMENT = (1<<8),
- IEEE80211_TXCTL_SHORT_PREAMBLE = (1<<9),
- IEEE80211_TXCTL_LONG_RETRY_LIMIT = (1<<10),
- IEEE80211_TXCTL_EAPOL_FRAME = (1<<11),
- IEEE80211_TXCTL_SEND_AFTER_DTIM = (1<<12),
- IEEE80211_TXCTL_AMPDU = (1<<13),
- IEEE80211_TXCTL_OFDM_HT = (1<<14),
- IEEE80211_TXCTL_GREEN_FIELD = (1<<15),
- IEEE80211_TXCTL_40_MHZ_WIDTH = (1<<16),
- IEEE80211_TXCTL_DUP_DATA = (1<<17),
- IEEE80211_TXCTL_SHORT_GI = (1<<18),
+ IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
+ IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1),
+ IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2),
+ IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3),
+ IEEE80211_TX_CTL_NO_ACK = BIT(4),
+ IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(5),
+ IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(6),
+ IEEE80211_TX_CTL_REQUEUE = BIT(7),
+ IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8),
+ IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9),
+ IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10),
+ IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11),
+ IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12),
+ IEEE80211_TX_CTL_AMPDU = BIT(13),
+ IEEE80211_TX_CTL_OFDM_HT = BIT(14),
+ IEEE80211_TX_CTL_GREEN_FIELD = BIT(15),
+ IEEE80211_TX_CTL_40_MHZ_WIDTH = BIT(16),
+ IEEE80211_TX_CTL_DUP_DATA = BIT(17),
+ IEEE80211_TX_CTL_SHORT_GI = BIT(18),
+ IEEE80211_TX_CTL_INJECTED = BIT(19),
+ IEEE80211_TX_STAT_TX_FILTERED = BIT(20),
+ IEEE80211_TX_STAT_ACK = BIT(21),
+ IEEE80211_TX_STAT_AMPDU = BIT(22),
};
-/* Transmit control fields. This data structure is passed to low-level driver
- * with each TX frame. The low-level driver is responsible for configuring
- * the hardware to use given values (depending on what is supported). */
-struct ieee80211_tx_control {
- struct ieee80211_vif *vif;
- struct ieee80211_rate *tx_rate;
-
- /* Transmit rate for RTS/CTS frame */
- struct ieee80211_rate *rts_cts_rate;
-
- /* retry rate for the last retries */
- struct ieee80211_rate *alt_retry_rate;
-
- u32 flags; /* tx control flags defined above */
- u8 key_idx; /* keyidx from hw->set_key(), undefined if
- * IEEE80211_TXCTL_DO_NOT_ENCRYPT is set */
- u8 retry_limit; /* 1 = only first attempt, 2 = one retry, ..
- * This could be used when set_retry_limit
- * is not implemented by the driver */
- u8 antenna_sel_tx; /* 0 = default/diversity, otherwise bit
- * position represents antenna number used */
- u8 icv_len; /* length of the ICV/MIC field in octets */
- u8 iv_len; /* length of the IV field in octets */
- u8 queue; /* hardware queue to use for this frame;
- * 0 = highest, hw->queues-1 = lowest */
- u16 aid; /* Station AID */
- int type; /* internal */
+#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE \
+ (sizeof(((struct sk_buff *)0)->cb) - 8)
+#define IEEE80211_TX_INFO_DRIVER_DATA_PTRS \
+ (IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *))
+
+/**
+ * struct ieee80211_tx_info - skb transmit information
+ *
+ * This structure is placed in skb->cb for three uses:
+ * (1) mac80211 TX control - mac80211 tells the driver what to do
+ * (2) driver internal use (if applicable)
+ * (3) TX status information - driver tells mac80211 what happened
+ *
+ * @flags: transmit info flags, defined above
+ * @retry_count: number of retries
+ * @excessive_retries: set to 1 if the frame was retried many times
+ * but not acknowledged
+ * @ampdu_ack_len: number of aggregated frames.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ampdu_ack_map: block ack bit map for the aggregation.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ack_signal: signal strength of the ACK frame
+ */
+struct ieee80211_tx_info {
+ /* common information */
+ u32 flags;
+ u8 band;
+ s8 tx_rate_idx;
+ u8 antenna_sel_tx;
+
+ /* 1 byte hole */
+
+ union {
+ struct {
+ struct ieee80211_vif *vif;
+ struct ieee80211_key_conf *hw_key;
+ unsigned long jiffies;
+ int ifindex;
+ u16 aid;
+ s8 rts_cts_rate_idx, alt_retry_rate_idx;
+ u8 retry_limit;
+ u8 icv_len;
+ u8 iv_len;
+ } control;
+ struct {
+ u64 ampdu_ack_map;
+ int ack_signal;
+ u8 retry_count;
+ bool excessive_retries;
+ u8 ampdu_ack_len;
+ } status;
+ void *driver_data[IEEE80211_TX_INFO_DRIVER_DATA_PTRS];
+ };
};
+static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
+{
+ return (struct ieee80211_tx_info *)skb->cb;
+}
+
/**
* enum mac80211_rx_flags - receive flags
* The low-level driver should provide this information (the subset
* supported by hardware) to the 802.11 code with each received
* frame.
+ *
* @mactime: value in microseconds of the 64-bit Time Synchronization Function
* (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
* @band: the active band when this frame was received
* @freq: frequency the radio was tuned to when receiving this frame, in MHz
- * @ssi: signal strength when receiving this frame
- * @signal: used as 'qual' in statistics reporting
- * @noise: PHY noise when receiving this frame
+ * @signal: signal strength when receiving this frame, either in dBm, in dB or
+ * unspecified depending on the hardware capabilities flags
+ * @IEEE80211_HW_SIGNAL_*
+ * @noise: noise when receiving this frame, in dBm.
+ * @qual: overall signal quality indication, in percent (0-100).
* @antenna: antenna used
* @rate_idx: index of data rate into band's supported rates
* @flag: %RX_FLAG_*
u64 mactime;
enum ieee80211_band band;
int freq;
- int ssi;
int signal;
int noise;
+ int qual;
int antenna;
int rate_idx;
int flag;
};
-/**
- * enum ieee80211_tx_status_flags - transmit status flags
- *
- * Status flags to indicate various transmit conditions.
- *
- * @IEEE80211_TX_STATUS_TX_FILTERED: The frame was not transmitted
- * because the destination STA was in powersave mode.
- * @IEEE80211_TX_STATUS_ACK: Frame was acknowledged
- * @IEEE80211_TX_STATUS_AMPDU: The frame was aggregated, so status
- * is for the whole aggregation.
- */
-enum ieee80211_tx_status_flags {
- IEEE80211_TX_STATUS_TX_FILTERED = 1<<0,
- IEEE80211_TX_STATUS_ACK = 1<<1,
- IEEE80211_TX_STATUS_AMPDU = 1<<2,
-};
-
-/**
- * struct ieee80211_tx_status - transmit status
- *
- * As much information as possible should be provided for each transmitted
- * frame with ieee80211_tx_status().
- *
- * @control: a copy of the &struct ieee80211_tx_control passed to the driver
- * in the tx() callback.
- * @flags: transmit status flags, defined above
- * @retry_count: number of retries
- * @excessive_retries: set to 1 if the frame was retried many times
- * but not acknowledged
- * @ampdu_ack_len: number of aggregated frames.
- * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
- * @ampdu_ack_map: block ack bit map for the aggregation.
- * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
- * @ack_signal: signal strength of the ACK frame
- * @queue_length: ?? REMOVE
- * @queue_number: ?? REMOVE
- */
-struct ieee80211_tx_status {
- struct ieee80211_tx_control control;
- u8 flags;
- u8 retry_count;
- bool excessive_retries;
- u8 ampdu_ack_len;
- u64 ampdu_ack_map;
- int ack_signal;
- int queue_length;
- int queue_number;
-};
-
/**
* enum ieee80211_conf_flags - configuration flags
*
u8 *ssid;
size_t ssid_len;
struct sk_buff *beacon;
- struct ieee80211_tx_control *beacon_control;
};
/**
* @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
* the driver for a TKIP key if it requires Michael MIC
* generation in software.
+ * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
+ * that the key is pairwise rather then a shared key.
*/
enum ieee80211_key_flags {
IEEE80211_KEY_FLAG_WMM_STA = 1<<0,
IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
+ IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
};
/**
* @flags: key flags, see &enum ieee80211_key_flags.
* @keyidx: the key index (0-3)
* @keylen: key material length
- * @key: key material
+ * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
+ * data block:
+ * - Temporal Encryption Key (128 bits)
+ * - Temporal Authenticator Tx MIC Key (64 bits)
+ * - Temporal Authenticator Rx MIC Key (64 bits)
+ *
*/
struct ieee80211_key_conf {
enum ieee80211_key_alg alg;
* @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
* Hardware is not capable of receiving frames with short preamble on
* the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_SIGNAL_UNSPEC:
+ * Hardware can provide signal values but we don't know its units. We
+ * expect values between 0 and @max_signal.
+ * If possible please provide dB or dBm instead.
+ *
+ * @IEEE80211_HW_SIGNAL_DB:
+ * Hardware gives signal values in dB, decibel difference from an
+ * arbitrary, fixed reference. We expect values between 0 and @max_signal.
+ * If possible please provide dBm instead.
+ *
+ * @IEEE80211_HW_SIGNAL_DBM:
+ * Hardware gives signal values in dBm, decibel difference from
+ * one milliwatt. This is the preferred method since it is standardized
+ * between different devices. @max_signal does not need to be set.
+ *
+ * @IEEE80211_HW_NOISE_DBM:
+ * Hardware can provide noise (radio interference) values in units dBm,
+ * decibel difference from one milliwatt.
+ *
+ * @IEEE80211_HW_SPECTRUM_MGMT:
+ * Hardware supports spectrum management defined in 802.11h
+ * Measurement, Channel Switch, Quieting, TPC
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
+ IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
+ IEEE80211_HW_SIGNAL_DB = 1<<6,
+ IEEE80211_HW_SIGNAL_DBM = 1<<7,
+ IEEE80211_HW_NOISE_DBM = 1<<8,
+ IEEE80211_HW_SPECTRUM_MGMT = 1<<9,
};
/**
* @conf: &struct ieee80211_conf, device configuration, don't use.
*
* @workqueue: single threaded workqueue available for driver use,
- * allocated by mac80211 on registration and flushed on
- * unregistration.
+ * allocated by mac80211 on registration and flushed when an
+ * interface is removed.
+ * NOTICE: All work performed on this workqueue should NEVER
+ * acquire the RTNL lock (i.e. Don't use the function
+ * ieee80211_iterate_active_interfaces())
*
* @priv: pointer to private area that was allocated for driver use
* along with this structure.
*
* @channel_change_time: time (in microseconds) it takes to change channels.
*
- * @max_rssi: Maximum value for ssi in RX information, use
- * negative numbers for dBm and 0 to indicate no support.
- *
- * @max_signal: like @max_rssi, but for the signal value.
- *
- * @max_noise: like @max_rssi, but for the noise value.
+ * @max_signal: Maximum value for signal (rssi) in RX information, used
+ * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @queues: number of available hardware transmit queues for
- * data packets. WMM/QoS requires at least four.
+ * data packets. WMM/QoS requires at least four, these
+ * queues need to have configurable access parameters.
+ *
+ * @ampdu_queues: number of available hardware transmit queues
+ * for A-MPDU packets, these have no access parameters
+ * because they're used only for A-MPDU frames. Note that
+ * mac80211 will not currently use any of the regular queues
+ * for aggregation.
*
* @rate_control_algorithm: rate control algorithm for this hardware.
* If unset (NULL), the default algorithm will be used. Must be
unsigned int extra_tx_headroom;
int channel_change_time;
int vif_data_size;
- u8 queues;
- s8 max_rssi;
+ u16 queues, ampdu_queues;
s8 max_signal;
- s8 max_noise;
};
/**
memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
}
+static inline int ieee80211_num_regular_queues(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_QOS
+ return hw->queues;
+#else
+ return 1;
+#endif
+}
+
+static inline int ieee80211_num_queues(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_QOS
+ return hw->queues + hw->ampdu_queues;
+#else
+ return 1;
+#endif
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (WARN_ON(c->tx_rate_idx < 0))
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->tx_rate_idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (c->control.rts_cts_rate_idx < 0)
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
+}
+
+static inline struct ieee80211_rate *
+ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
+ const struct ieee80211_tx_info *c)
+{
+ if (c->control.alt_retry_rate_idx < 0)
+ return NULL;
+ return &hw->wiphy->bands[c->band]->bitrates[c->control.alt_retry_rate_idx];
+}
+
/**
* DOC: Hardware crypto acceleration
*
* @tx: Handler that 802.11 module calls for each transmitted frame.
* skb contains the buffer starting from the IEEE 802.11 header.
* The low-level driver should send the frame out based on
- * configuration in the TX control data. Must be implemented and
- * atomic.
+ * configuration in the TX control data. This handler should,
+ * preferably, never fail and stop queues appropriately, more
+ * importantly, however, it must never fail for A-MPDU-queues.
+ * Must be implemented and atomic.
*
* @start: Called before the first netdevice attached to the hardware
* is enabled. This should turn on the hardware and must turn on
* of assocaited station or AP.
*
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
- * bursting) for a hardware TX queue. The @queue parameter uses the
- * %IEEE80211_TX_QUEUE_* constants. Must be atomic.
+ * bursting) for a hardware TX queue. Must be atomic.
*
* @get_tx_stats: Get statistics of the current TX queue status. This is used
* to get number of currently queued packets (queue length), maximum queue
* size (limit), and total number of packets sent using each TX queue
- * (count). This information is used for WMM to find out which TX
- * queues have room for more packets and by hostapd to provide
- * statistics about the current queueing state to external programs.
+ * (count). The 'stats' pointer points to an array that has hw->queues +
+ * hw->ampdu_queues items.
*
* @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
* this is only used for IBSS mode debugging and, as such, is not a
* that TX/RX_STOP can pass NULL for this parameter.
*/
struct ieee80211_ops {
- int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
- struct ieee80211_tx_control *control);
+ int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
int (*start)(struct ieee80211_hw *hw);
void (*stop)(struct ieee80211_hw *hw);
int (*add_interface)(struct ieee80211_hw *hw,
u32 short_retry, u32 long_retr);
void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
enum sta_notify_cmd, const u8 *addr);
- int (*conf_tx)(struct ieee80211_hw *hw, int queue,
+ int (*conf_tx)(struct ieee80211_hw *hw, u16 queue,
const struct ieee80211_tx_queue_params *params);
int (*get_tx_stats)(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats);
u64 (*get_tsf)(struct ieee80211_hw *hw);
void (*reset_tsf)(struct ieee80211_hw *hw);
int (*beacon_update)(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_control *control);
+ struct sk_buff *skb);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
int (*ampdu_action)(struct ieee80211_hw *hw,
enum ieee80211_ampdu_mlme_action action,
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
- * @status: status information for this frame; the status pointer need not
- * be valid after this function returns and is not freed by mac80211,
- * it is recommended that it points to a stack area
*/
void ieee80211_tx_status(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status);
+ struct sk_buff *skb);
/**
* ieee80211_tx_status_irqsafe - irq-safe transmit status callback
*
* @hw: the hardware the frame was transmitted by
* @skb: the frame that was transmitted, owned by mac80211 after this call
- * @status: status information for this frame; the status pointer need not
- * be valid after this function returns and is not freed by mac80211,
- * it is recommended that it points to a stack area
*/
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
- struct sk_buff *skb,
- struct ieee80211_tx_status *status);
+ struct sk_buff *skb);
/**
* ieee80211_beacon_get - beacon generation function
* is responsible of freeing it.
*/
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
- struct ieee80211_vif *vif,
- struct ieee80211_tx_control *control);
+ struct ieee80211_vif *vif);
/**
* ieee80211_rts_get - RTS frame generation function
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the RTS.
* @frame_len: the frame length (in octets).
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
* @rts: The buffer where to store the RTS frame.
*
* If the RTS frames are generated by the host system (i.e., not in
*/
void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl,
+ const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_rts *rts);
/**
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the RTS.
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the RTS is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
*/
__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif, size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl);
+ const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_ctstoself_get - CTS-to-self frame generation function
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the CTS-to-self.
* @frame_len: the frame length (in octets).
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
* @cts: The buffer where to store the CTS-to-self frame.
*
* If the CTS-to-self frames are generated by the host system (i.e., not in
void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl,
+ const struct ieee80211_tx_info *frame_txctl,
struct ieee80211_cts *cts);
/**
* @hw: pointer obtained from ieee80211_alloc_hw().
* @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
- * @frame_txctl: &struct ieee80211_tx_control of the frame.
+ * @frame_txctl: &struct ieee80211_tx_info of the frame.
*
* If the CTS-to-self is generated in firmware, but the host system must provide
* the duration field, the low-level driver uses this function to receive
__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
size_t frame_len,
- const struct ieee80211_tx_control *frame_txctl);
+ const struct ieee80211_tx_info *frame_txctl);
/**
* ieee80211_generic_frame_duration - Calculate the duration field for a frame
* use common code for all beacons.
*/
struct sk_buff *
-ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
- struct ieee80211_tx_control *control);
+ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
/**
* ieee80211_get_hdrlen_from_skb - get header length from data
*
* @skb: the frame
*/
-int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
+unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
/**
* ieee80211_get_hdrlen - get header length from frame control
*/
int ieee80211_get_hdrlen(u16 fc);
+/**
+ * ieee80211_hdrlen - get header length in bytes from frame control
+ * @fc: frame control field in little-endian format
+ */
+unsigned int ieee80211_hdrlen(__le16 fc);
+
/**
* ieee80211_get_tkip_key - get a TKIP rc4 for skb
*
*/
void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
-/**
- * ieee80211_start_queues - start all queues
- * @hw: pointer to as obtained from ieee80211_alloc_hw().
- *
- * Drivers should use this function instead of netif_start_queue.
- */
-void ieee80211_start_queues(struct ieee80211_hw *hw);
-
/**
* ieee80211_stop_queues - stop all queues
* @hw: pointer as obtained from ieee80211_alloc_hw().
projects / linux-2.6-omap-h63xx.git / blobdiff