#include <linux/device.h>
#include <linux/pci.h>
#include <linux/completion.h>
+#include <linux/pm.h>
#ifdef CONFIG_BLK_DEV_IDEACPI
#include <acpi/acpi.h>
#endif
#define PARTN_BITS 6 /* number of minor dev bits for partitions */
#define MAX_DRIVES 2 /* per interface; 2 assumed by lots of code */
#define SECTOR_SIZE 512
-#define SECTOR_WORDS (SECTOR_SIZE / 4) /* number of 32bit words per sector */
+
#define IDE_LARGE_SEEK(b1,b2,t) (((b1) > (b2) + (t)) || ((b2) > (b1) + (t)))
/*
* Timeouts for various operations:
*/
-#define WAIT_DRQ (HZ/10) /* 100msec - spec allows up to 20ms */
-#define WAIT_READY (5*HZ) /* 5sec - some laptops are very slow */
-#define WAIT_PIDENTIFY (10*HZ) /* 10sec - should be less than 3ms (?), if all ATAPI CD is closed at boot */
-#define WAIT_WORSTCASE (30*HZ) /* 30sec - worst case when spinning up */
-#define WAIT_CMD (10*HZ) /* 10sec - maximum wait for an IRQ to happen */
-#define WAIT_MIN_SLEEP (2*HZ/100) /* 20msec - minimum sleep time */
+enum {
+ /* spec allows up to 20ms */
+ WAIT_DRQ = HZ / 10, /* 100ms */
+ /* some laptops are very slow */
+ WAIT_READY = 5 * HZ, /* 5s */
+ /* should be less than 3ms (?), if all ATAPI CD is closed at boot */
+ WAIT_PIDENTIFY = 10 * HZ, /* 10s */
+ /* worst case when spinning up */
+ WAIT_WORSTCASE = 30 * HZ, /* 30s */
+ /* maximum wait for an IRQ to happen */
+ WAIT_CMD = 10 * HZ, /* 10s */
+ /* Some drives require a longer IRQ timeout. */
+ WAIT_FLOPPY_CMD = 50 * HZ, /* 50s */
+ /*
+ * Some drives (for example, Seagate STT3401A Travan) require a very
+ * long timeout, because they don't return an interrupt or clear their
+ * BSY bit until after the command completes (even retension commands).
+ */
+ WAIT_TAPE_CMD = 900 * HZ, /* 900s */
+ /* minimum sleep time */
+ WAIT_MIN_SLEEP = HZ / 50, /* 20ms */
+};
/*
* Op codes for special requests to be handled by ide_special_rq().
enum {
IDE_AFLAG_DRQ_INTERRUPT = (1 << 0),
IDE_AFLAG_MEDIA_CHANGED = (1 << 1),
-
- /* ide-cd */
/* Drive cannot lock the door. */
IDE_AFLAG_NO_DOORLOCK = (1 << 2),
+
+ /* ide-cd */
/* Drive cannot eject the disc. */
IDE_AFLAG_NO_EJECT = (1 << 3),
/* Drive is a pre ATAPI 1.2 drive. */
IDE_AFLAG_CLIK_DRIVE = (1 << 19),
/* Requires BH algorithm for packets */
IDE_AFLAG_ZIP_DRIVE = (1 << 20),
+ /* Write protect */
+ IDE_AFLAG_WP = (1 << 21),
+ /* Supports format progress report */
+ IDE_AFLAG_SRFP = (1 << 22),
/* ide-tape */
- IDE_AFLAG_IGNORE_DSC = (1 << 21),
+ IDE_AFLAG_IGNORE_DSC = (1 << 23),
/* 0 When the tape position is unknown */
- IDE_AFLAG_ADDRESS_VALID = (1 << 22),
+ IDE_AFLAG_ADDRESS_VALID = (1 << 24),
/* Device already opened */
- IDE_AFLAG_BUSY = (1 << 23),
+ IDE_AFLAG_BUSY = (1 << 25),
/* Attempt to auto-detect the current user block size */
- IDE_AFLAG_DETECT_BS = (1 << 24),
+ IDE_AFLAG_DETECT_BS = (1 << 26),
/* Currently on a filemark */
- IDE_AFLAG_FILEMARK = (1 << 25),
+ IDE_AFLAG_FILEMARK = (1 << 27),
/* 0 = no tape is loaded, so we don't rewind after ejecting */
- IDE_AFLAG_MEDIUM_PRESENT = (1 << 26),
+ IDE_AFLAG_MEDIUM_PRESENT = (1 << 28),
- IDE_AFLAG_NO_AUTOCLOSE = (1 << 27),
+ IDE_AFLAG_NO_AUTOCLOSE = (1 << 29),
};
struct ide_drive_s {
unsigned forced_geom : 1; /* 1 if hdx=c,h,s was given at boot */
unsigned no_unmask : 1; /* disallow setting unmask bit */
unsigned no_io_32bit : 1; /* disallow enabling 32bit I/O */
- unsigned atapi_overlap : 1; /* ATAPI overlap (not supported) */
unsigned doorlocking : 1; /* for removable only: door lock/unlock works */
unsigned nodma : 1; /* disallow DMA */
unsigned blocked : 1; /* 1=powermanagment told us not to do anything, so sleep nicely */
u8 major; /* our major number */
u8 index; /* 0 for ide0; 1 for ide1; ... */
u8 channel; /* for dual-port chips: 0=primary, 1=secondary */
- u8 bus_state; /* power state of the IDE bus */
u32 host_flags;
ide_hwif_t *ports[MAX_HWIFS];
unsigned int n_ports;
struct device *dev[2];
+ unsigned int (*init_chipset)(struct pci_dev *);
unsigned long host_flags;
void *host_priv;
};
PC_FLAG_TIMEDOUT = (1 << 7),
};
+/*
+ * With each packet command, we allocate a buffer of IDE_PC_BUFFER_SIZE bytes.
+ * This is used for several packet commands (not for READ/WRITE commands).
+ */
+#define IDE_PC_BUFFER_SIZE 256
+
struct ide_atapi_pc {
/* actual packet bytes */
u8 c[12];
* those are more or less driver-specific and some of them are subject
* to change/removal later.
*/
- u8 pc_buf[256];
+ u8 pc_buf[IDE_PC_BUFFER_SIZE];
/* idetape only */
struct idetape_bh *bh;
struct ide_driver_s {
const char *version;
u8 media;
- unsigned supports_dsc_overlap : 1;
ide_startstop_t (*do_request)(ide_drive_t *, struct request *, sector_t);
int (*end_request)(ide_drive_t *, int, int);
ide_startstop_t (*error)(ide_drive_t *, struct request *rq, u8, u8);
int ide_device_get(ide_drive_t *);
void ide_device_put(ide_drive_t *);
-int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *, unsigned, unsigned long);
+struct ide_ioctl_devset {
+ unsigned int get_ioctl;
+ unsigned int set_ioctl;
+
+ int (*get)(ide_drive_t *);
+ int (*set)(ide_drive_t *, int);
+};
+
+int ide_setting_ioctl(ide_drive_t *, struct block_device *, unsigned int,
+ unsigned long, const struct ide_ioctl_devset *);
+
+int generic_ide_ioctl(ide_drive_t *, struct file *, struct block_device *,
+ unsigned, unsigned long);
extern int ide_vlb_clk;
extern int ide_pci_clk;
void ide_input_data(ide_drive_t *, struct request *, void *, unsigned int);
void ide_output_data(ide_drive_t *, struct request *, void *, unsigned int);
+int ide_io_buffers(ide_drive_t *, struct ide_atapi_pc *, unsigned int, int);
+
extern void SELECT_DRIVE(ide_drive_t *);
void SELECT_MASK(ide_drive_t *, int);
void ide_pktcmd_tf_load(ide_drive_t *, u32, u16, u8);
+int ide_check_atapi_device(ide_drive_t *, const char *);
+
+void ide_init_pc(struct ide_atapi_pc *);
+
+/*
+ * Special requests for ide-tape block device strategy routine.
+ *
+ * In order to service a character device command, we add special requests to
+ * the tail of our block device request queue and wait for their completion.
+ */
+enum {
+ REQ_IDETAPE_PC1 = (1 << 0), /* packet command (first stage) */
+ REQ_IDETAPE_PC2 = (1 << 1), /* packet command (second stage) */
+ REQ_IDETAPE_READ = (1 << 2),
+ REQ_IDETAPE_WRITE = (1 << 3),
+};
+
+void ide_queue_pc_head(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *,
+ struct request *);
+int ide_queue_pc_tail(ide_drive_t *, struct gendisk *, struct ide_atapi_pc *);
+
+int ide_do_test_unit_ready(ide_drive_t *, struct gendisk *);
+int ide_do_start_stop(ide_drive_t *, struct gendisk *, int);
+int ide_set_media_lock(ide_drive_t *, struct gendisk *, int);
+
ide_startstop_t ide_pc_intr(ide_drive_t *drive, struct ide_atapi_pc *pc,
ide_handler_t *handler, unsigned int timeout, ide_expiry_t *expiry,
void (*update_buffers)(ide_drive_t *, struct ide_atapi_pc *),
void (*retry_pc)(ide_drive_t *), void (*dsc_handle)(ide_drive_t *),
- void (*io_buffers)(ide_drive_t *, struct ide_atapi_pc *, unsigned int,
+ int (*io_buffers)(ide_drive_t *, struct ide_atapi_pc *, unsigned int,
int));
ide_startstop_t ide_transfer_pc(ide_drive_t *, struct ide_atapi_pc *,
ide_handler_t *, unsigned int, ide_expiry_t *);
int ide_no_data_taskfile(ide_drive_t *, ide_task_t *);
int ide_taskfile_ioctl(ide_drive_t *, unsigned int, unsigned long);
-int ide_cmd_ioctl(ide_drive_t *, unsigned int, unsigned long);
-int ide_task_ioctl(ide_drive_t *, unsigned int, unsigned long);
extern int ide_driveid_update(ide_drive_t *);
extern int ide_config_drive_speed(ide_drive_t *, u8);
const struct ide_port_info *, void *);
void ide_pci_remove(struct pci_dev *);
+#ifdef CONFIG_PM
+int ide_pci_suspend(struct pci_dev *, pm_message_t);
+int ide_pci_resume(struct pci_dev *);
+#else
+#define ide_pci_suspend NULL
+#define ide_pci_resume NULL
+#endif
+
void ide_map_sg(ide_drive_t *, struct request *);
void ide_init_sg_cmd(ide_drive_t *, struct request *);
extern void ide_toggle_bounce(ide_drive_t *drive, int on);
extern int ide_set_xfer_rate(ide_drive_t *drive, u8 rate);
-static inline int ide_dev_has_iordy(u16 *id)
-{
- return ((id[ATA_ID_FIELD_VALID] & 2) && ata_id_has_iordy(id)) ? 1 : 0;
-}
-
-static inline int ide_dev_is_sata(u16 *id)
-{
- /*
- * See if word 93 is 0 AND drive is at least ATA-5 compatible
- * verifying that word 80 by casting it to a signed type --
- * this trick allows us to filter out the reserved values of
- * 0x0000 and 0xffff along with the earlier ATA revisions...
- */
- if (id[ATA_ID_HW_CONFIG] == 0 && (short)id[ATA_ID_MAJOR_VER] >= 0x0020)
- return 1;
- return 0;
-}
-
u64 ide_get_lba_addr(struct ide_taskfile *, int);
u8 ide_dump_status(ide_drive_t *, const char *, u8);
extern struct bus_type ide_bus_type;
extern struct class *ide_port_class;
-/* check if CACHE FLUSH (EXT) command is supported (bits defined in ATA-6) */
-#define ide_id_has_flush_cache(id) ((id)[ATA_ID_CFS_ENABLE_2] & 0x3000)
-
-/* some Maxtor disks have bit 13 defined incorrectly so check bit 10 too */
-#define ide_id_has_flush_cache_ext(id) \
- (((id)[ATA_ID_CFS_ENABLE_2] & 0x2400) == 0x2400)
-
static inline void ide_dump_identify(u8 *id)
{
print_hex_dump(KERN_INFO, "", DUMP_PREFIX_NONE, 16, 2, id, 512, 0);