* set_geometry : respecify drive geometry
* recalibrate : seek to cyl 0
* set_multmode : set multmode count
- * set_tune : tune interface for drive
- * serviced : service command
* reserved : unused
*/
typedef union {
unsigned set_geometry : 1;
unsigned recalibrate : 1;
unsigned set_multmode : 1;
- unsigned set_tune : 1;
- unsigned serviced : 1;
- unsigned reserved : 3;
+ unsigned reserved : 5;
} b;
} special_t;
-/*
- * ATA-IDE Select Register, aka Device-Head
- *
- * head : always zeros here
- * unit : drive select number: 0/1
- * bit5 : always 1
- * lba : using LBA instead of CHS
- * bit7 : always 1
- */
-typedef union {
- unsigned all : 8;
- struct {
-#if defined(__LITTLE_ENDIAN_BITFIELD)
- unsigned head : 4;
- unsigned unit : 1;
- unsigned bit5 : 1;
- unsigned lba : 1;
- unsigned bit7 : 1;
-#elif defined(__BIG_ENDIAN_BITFIELD)
- unsigned bit7 : 1;
- unsigned lba : 1;
- unsigned bit5 : 1;
- unsigned unit : 1;
- unsigned head : 4;
-#else
-#error "Please fix <asm/byteorder.h>"
-#endif
- } b;
-} select_t, ata_select_t;
-
/*
* Status returned from various ide_ functions
*/
IDE_DFLAG_NOWERR = (1 << 24),
/* retrying in PIO */
IDE_DFLAG_DMA_PIO_RETRY = (1 << 25),
+ IDE_DFLAG_LBA = (1 << 26),
};
struct ide_drive_s {
unsigned long timeout; /* max time to wait for irq */
special_t special; /* special action flags */
- select_t select; /* basic drive/head select reg value */
+ u8 select; /* basic drive/head select reg value */
u8 retry_pio; /* retrying dma capable host in pio */
u8 waiting_for_dma; /* dma currently in progress */
u8 ready_stat; /* min status value for drive ready */
u8 mult_count; /* current multiple sector setting */
u8 mult_req; /* requested multiple sector setting */
- u8 tune_req; /* requested drive tuning setting */
u8 io_32bit; /* 0=16-bit, 1=32-bit, 2/3=32bit+sync */
u8 bad_wstat; /* used for ignoring ATA_DF */
u8 head; /* "real" number of heads */
void *hwif_data; /* extra hwif data */
- unsigned dma;
-
#ifdef CONFIG_BLK_DEV_IDEACPI
struct ide_acpi_hwif_link *acpidata;
#endif
}
/*
- * Power Management step value (rq->pm->pm_step).
- *
- * The step value starts at 0 (ide_pm_state_start_suspend) for a
- * suspend operation or 1000 (ide_pm_state_start_resume) for a
- * resume operation.
+ * Power Management state machine (rq->pm->pm_step).
*
- * For each step, the core calls the subdriver start_power_step() first.
+ * For each step, the core calls ide_start_power_step() first.
* This can return:
* - ide_stopped : In this case, the core calls us back again unless
* step have been set to ide_power_state_completed.
* - ide_started : In this case, the channel is left busy until an
* async event (interrupt) occurs.
- * Typically, start_power_step() will issue a taskfile request with
+ * Typically, ide_start_power_step() will issue a taskfile request with
* do_rw_taskfile().
*
- * Upon reception of the interrupt, the core will call complete_power_step()
+ * Upon reception of the interrupt, the core will call ide_complete_power_step()
* with the error code if any. This routine should update the step value
* and return. It should not start a new request. The core will call
- * start_power_step for the new step value, unless step have been set to
- * ide_power_state_completed.
- *
- * Subdrivers are expected to define their own additional power
- * steps from 1..999 for suspend and from 1001..1999 for resume,
- * other values are reserved for future use.
+ * ide_start_power_step() for the new step value, unless step have been
+ * set to IDE_PM_COMPLETED.
*/
-
enum {
- ide_pm_state_completed = -1,
- ide_pm_state_start_suspend = 0,
- ide_pm_state_start_resume = 1000,
+ IDE_PM_START_SUSPEND,
+ IDE_PM_FLUSH_CACHE = IDE_PM_START_SUSPEND,
+ IDE_PM_STANDBY,
+
+ IDE_PM_START_RESUME,
+ IDE_PM_RESTORE_PIO = IDE_PM_START_RESUME,
+ IDE_PM_IDLE,
+ IDE_PM_RESTORE_DMA,
+
+ IDE_PM_COMPLETED,
};
/*