int gpio_base;
unsigned irq_base, irq_end;
+ /* package the two LED signals as output-only GPIOs? */
+ bool use_leds;
+
+ /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
+ u8 mmc_cd;
+
/* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
* should be enabled. Else, if that bit is set in "pulldowns",
* that pulldown is enabled. Don't waste power by letting any
/*----------------------------------------------------------------------*/
+int twl4030_sih_setup(int module);
+
/*
* FIXME completely stop using TWL4030_IRQ_BASE ... instead, pass the
* IRQ data to subsidiary devices using platform device resources.
#define TWL4030_MODIRQ_BCI (TWL4030_IRQ_BASE + 2)
#define TWL4030_MODIRQ_MADC (TWL4030_IRQ_BASE + 3)
/* #define TWL4030_MODIRQ_USB (TWL4030_IRQ_BASE + 4) */
-#define TWL4030_MODIRQ_PWR (TWL4030_IRQ_BASE + 5)
+/* #define TWL4030_MODIRQ_PWR (TWL4030_IRQ_BASE + 5) */
#define TWL4030_PWRIRQ_PWRBTN (TWL4030_PWR_IRQ_BASE + 0)
-#define TWL4030_PWRIRQ_CHG_PRES (TWL4030_PWR_IRQ_BASE + 1)
-#define TWL4030_PWRIRQ_USB_PRES (TWL4030_PWR_IRQ_BASE + 2)
-#define TWL4030_PWRIRQ_RTC (TWL4030_PWR_IRQ_BASE + 3)
-#define TWL4030_PWRIRQ_HOT_DIE (TWL4030_PWR_IRQ_BASE + 4)
-#define TWL4030_PWRIRQ_PWROK_TIMEOUT (TWL4030_PWR_IRQ_BASE + 5)
-#define TWL4030_PWRIRQ_MBCHG (TWL4030_PWR_IRQ_BASE + 6)
-#define TWL4030_PWRIRQ_SC_DETECT (TWL4030_PWR_IRQ_BASE + 7)
+/* #define TWL4030_PWRIRQ_CHG_PRES (TWL4030_PWR_IRQ_BASE + 1) */
+/* #define TWL4030_PWRIRQ_USB_PRES (TWL4030_PWR_IRQ_BASE + 2) */
+/* #define TWL4030_PWRIRQ_RTC (TWL4030_PWR_IRQ_BASE + 3) */
+/* #define TWL4030_PWRIRQ_HOT_DIE (TWL4030_PWR_IRQ_BASE + 4) */
+/* #define TWL4030_PWRIRQ_PWROK_TIMEOUT (TWL4030_PWR_IRQ_BASE + 5) */
+/* #define TWL4030_PWRIRQ_MBCHG (TWL4030_PWR_IRQ_BASE + 6) */
+/* #define TWL4030_PWRIRQ_SC_DETECT (TWL4030_PWR_IRQ_BASE + 7) */
/* Rest are unsued currently*/
/* TWL4030 GPIO interrupt definitions */
#define TWL4030_GPIO_IRQ_NO(n) (TWL4030_GPIO_IRQ_BASE + (n))
-#define TWL4030_GPIO_IS_ENABLE 1
/*
* Exported TWL4030 GPIO APIs
*
* WARNING -- use standard GPIO and IRQ calls instead; these will vanish.
*/
-int twl4030_get_gpio_datain(int gpio);
-int twl4030_request_gpio(int gpio);
int twl4030_set_gpio_debounce(int gpio, int enable);
-int twl4030_free_gpio(int gpio);
#if defined(CONFIG_TWL4030_BCI_BATTERY) || \
defined(CONFIG_TWL4030_BCI_BATTERY_MODULE)