/*
- * File: drivers/video/omap/omap2/rfbi.c
- *
* OMAP2 Remote Frame Buffer Interface support
*
* Copyright (C) 2005 Nokia Corporation
#include "dispc.h"
+/* To work around an RFBI transfer rate limitation */
+#define OMAP_RFBI_RATE_LIMIT 1
+
#define RFBI_BASE 0x48050800
#define RFBI_REVISION 0x0000
#define RFBI_SYSCONFIG 0x0010
struct omapfb_device *fbdev;
struct clk *dss_ick;
struct clk *dss1_fck;
+ unsigned tearsync_pin_cnt;
+ unsigned tearsync_mode;
} rfbi;
static inline void rfbi_write_reg(int idx, u32 val)
return ret;
}
+#ifdef OMAP_RFBI_RATE_LIMIT
+static unsigned long rfbi_get_max_tx_rate(void)
+{
+ unsigned long l4_rate, dss1_rate;
+ int min_l4_ticks = 0;
+ int i;
+
+ /* According to TI this can't be calculated so make the
+ * adjustments for a couple of known frequencies and warn for
+ * others.
+ */
+ static const struct {
+ unsigned long l4_clk; /* HZ */
+ unsigned long dss1_clk; /* HZ */
+ unsigned long min_l4_ticks;
+ } ftab[] = {
+ { 55, 132, 7, }, /* 7.86 MPix/s */
+ { 110, 110, 12, }, /* 9.16 MPix/s */
+ { 110, 132, 10, }, /* 11 Mpix/s */
+ { 120, 120, 10, }, /* 12 Mpix/s */
+ { 133, 133, 10, }, /* 13.3 Mpix/s */
+ };
+
+ l4_rate = rfbi.l4_khz / 1000;
+ dss1_rate = clk_get_rate(rfbi.dss1_fck) / 1000000;
+
+ for (i = 0; i < ARRAY_SIZE(ftab); i++) {
+ /* Use a window instead of an exact match, to account
+ * for different DPLL multiplier / divider pairs.
+ */
+ if (abs(ftab[i].l4_clk - l4_rate) < 3 &&
+ abs(ftab[i].dss1_clk - dss1_rate) < 3) {
+ min_l4_ticks = ftab[i].min_l4_ticks;
+ break;
+ }
+ }
+ if (i == ARRAY_SIZE(ftab)) {
+ /* Can't be sure, return anyway the maximum not
+ * rate-limited. This might cause a problem only for the
+ * tearing synchronisation.
+ */
+ dev_err(rfbi.fbdev->dev,
+ "can't determine maximum RFBI transfer rate\n");
+ return rfbi.l4_khz * 1000;
+ }
+ return rfbi.l4_khz * 1000 / min_l4_ticks;
+}
+#else
+static int rfbi_get_max_tx_rate(void)
+{
+ return rfbi.l4_khz * 1000;
+}
+#endif
+
+
static int rfbi_convert_timings(struct extif_timings *t)
{
u32 l;
return 0;
}
+static int rfbi_setup_tearsync(unsigned pin_cnt,
+ unsigned hs_pulse_time, unsigned vs_pulse_time,
+ int hs_pol_inv, int vs_pol_inv, int extif_div)
+{
+ int hs, vs;
+ int min;
+ u32 l;
+
+ if (pin_cnt != 1 && pin_cnt != 2)
+ return -EINVAL;
+
+ hs = ps_to_rfbi_ticks(hs_pulse_time, 1);
+ vs = ps_to_rfbi_ticks(vs_pulse_time, 1);
+ if (hs < 2)
+ return -EDOM;
+ if (pin_cnt == 2)
+ min = 2;
+ else
+ min = 4;
+ if (vs < min)
+ return -EDOM;
+ if (vs == hs)
+ return -EINVAL;
+ rfbi.tearsync_pin_cnt = pin_cnt;
+ dev_dbg(rfbi.fbdev->dev,
+ "setup_tearsync: pins %d hs %d vs %d hs_inv %d vs_inv %d\n",
+ pin_cnt, hs, vs, hs_pol_inv, vs_pol_inv);
+
+ rfbi_enable_clocks(1);
+ rfbi_write_reg(RFBI_HSYNC_WIDTH, hs);
+ rfbi_write_reg(RFBI_VSYNC_WIDTH, vs);
+
+ l = rfbi_read_reg(RFBI_CONFIG0);
+ if (hs_pol_inv)
+ l &= ~(1 << 21);
+ else
+ l |= 1 << 21;
+ if (vs_pol_inv)
+ l &= ~(1 << 20);
+ else
+ l |= 1 << 20;
+ rfbi_enable_clocks(0);
+
+ return 0;
+}
+
+static int rfbi_enable_tearsync(int enable, unsigned line)
+{
+ u32 l;
+
+ dev_dbg(rfbi.fbdev->dev, "tearsync %d line %d mode %d\n",
+ enable, line, rfbi.tearsync_mode);
+ if (line > (1 << 11) - 1)
+ return -EINVAL;
+
+ rfbi_enable_clocks(1);
+ l = rfbi_read_reg(RFBI_CONFIG0);
+ l &= ~(0x3 << 2);
+ if (enable) {
+ rfbi.tearsync_mode = rfbi.tearsync_pin_cnt;
+ l |= rfbi.tearsync_mode << 2;
+ } else
+ rfbi.tearsync_mode = 0;
+ rfbi_write_reg(RFBI_CONFIG0, l);
+ rfbi_write_reg(RFBI_LINE_NUMBER, line);
+ rfbi_enable_clocks(0);
+
+ return 0;
+}
+
static void rfbi_write_command(const void *buf, unsigned int len)
{
rfbi_enable_clocks(1);
rfbi_write_reg(RFBI_PIXEL_CNT, width * height);
w = rfbi_read_reg(RFBI_CONTROL);
- /* Enable, Internal trigger */
- rfbi_write_reg(RFBI_CONTROL, w | (1 << 0) | (1 << 4));
+ w |= 1; /* enable */
+ if (!rfbi.tearsync_mode)
+ w |= 1 << 4; /* internal trigger, reset by HW */
+ rfbi_write_reg(RFBI_CONTROL, w);
omap_dispc_enable_lcd_out(1);
}
.init = rfbi_init,
.cleanup = rfbi_cleanup,
.get_clk_info = rfbi_get_clk_info,
+ .get_max_tx_rate = rfbi_get_max_tx_rate,
.set_bits_per_cycle = rfbi_set_bits_per_cycle,
.convert_timings = rfbi_convert_timings,
.set_timings = rfbi_set_timings,
.read_data = rfbi_read_data,
.write_data = rfbi_write_data,
.transfer_area = rfbi_transfer_area,
+ .setup_tearsync = rfbi_setup_tearsync,
+ .enable_tearsync = rfbi_enable_tearsync,
.max_transmit_size = (u32)~0,
};