*
* SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
*
- * Copyright (C) 2002 - 2006 Paul Mundt
+ * Copyright (C) 2002 - 2008 Paul Mundt
* Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
*
* based off of the old drivers/char/sh-sci.c by:
#include <linux/cpufreq.h>
#include <linux/clk.h>
#include <linux/ctype.h>
+#include <linux/err.h>
#ifdef CONFIG_SUPERH
#include <asm/clock.h>
struct timer_list break_timer;
int break_flag;
-#ifdef CONFIG_SUPERH
+#ifdef CONFIG_HAVE_CLK
/* Port clock */
struct clk *clk;
#endif
}
#endif
-#if defined(SCI_ONLY) || defined(SCI_AND_SCIF) && \
- defined(__H8300H__) || defined(__H8300S__)
+#if defined(__H8300H__) || defined(__H8300S__)
static void sci_init_pins_sci(struct uart_port* port, unsigned int cflag)
{
int ch = (port->mapbase - SMR0) >> 3;
#define sci_init_pins_irda NULL
#endif
-#ifdef SCI_ONLY
-#define sci_init_pins_scif NULL
-#endif
-
-#if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
#if defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag)
{
return sci_in(port, SCFDR) & SCIF_RFDC_MASK;
}
#endif
-#endif /* SCIF_ONLY || SCI_AND_SCIF */
static inline int sci_txroom(struct uart_port *port)
{
return;
}
-#ifndef SCI_ONLY
if (port->type == PORT_SCIF)
count = scif_txroom(port);
else
-#endif
count = sci_txroom(port);
do {
} else {
ctrl = sci_in(port, SCSCR);
-#if !defined(SCI_ONLY)
if (port->type == PORT_SCIF) {
sci_in(port, SCxSR); /* Dummy read */
sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port));
}
-#endif
ctrl |= SCI_CTRL_FLAGS_TIE;
sci_out(port, SCSCR, ctrl);
return;
while (1) {
-#if !defined(SCI_ONLY)
if (port->type == PORT_SCIF)
count = scif_rxroom(port);
else
-#endif
count = sci_rxroom(port);
/* Don't copy more bytes than there is room for in the buffer */
static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
{
- unsigned short ssr_status, scr_status;
- struct uart_port *port = ptr;
+ unsigned short ssr_status, scr_status;
+ struct uart_port *port = ptr;
+ irqreturn_t ret = IRQ_NONE;
ssr_status = sci_in(port,SCxSR);
scr_status = sci_in(port,SCSCR);
/* Tx Interrupt */
- if ((ssr_status & 0x0020) && (scr_status & 0x0080))
- sci_tx_interrupt(irq, ptr);
+ if ((ssr_status & 0x0020) && (scr_status & SCI_CTRL_FLAGS_TIE))
+ ret = sci_tx_interrupt(irq, ptr);
/* Rx Interrupt */
- if ((ssr_status & 0x0002) && (scr_status & 0x0040))
- sci_rx_interrupt(irq, ptr);
+ if ((ssr_status & 0x0002) && (scr_status & SCI_CTRL_FLAGS_RIE))
+ ret = sci_rx_interrupt(irq, ptr);
/* Error Interrupt */
- if ((ssr_status & 0x0080) && (scr_status & 0x0400))
- sci_er_interrupt(irq, ptr);
+ if ((ssr_status & 0x0080) && (scr_status & SCI_CTRL_FLAGS_REIE))
+ ret = sci_er_interrupt(irq, ptr);
/* Break Interrupt */
- if ((ssr_status & 0x0010) && (scr_status & 0x0200))
- sci_br_interrupt(irq, ptr);
+ if ((ssr_status & 0x0010) && (scr_status & SCI_CTRL_FLAGS_REIE))
+ ret = sci_br_interrupt(irq, ptr);
- return IRQ_HANDLED;
+ return ret;
}
-#ifdef CONFIG_CPU_FREQ
+#if defined(CONFIG_CPU_FREQ) && defined(CONFIG_HAVE_CLK)
/*
* Here we define a transistion notifier so that we can update all of our
* ports' baud rate when the peripheral clock changes.
* Clean this up later..
*/
clk = clk_get(NULL, "module_clk");
- port->uartclk = clk_get_rate(clk) * 16;
+ port->uartclk = clk_get_rate(clk);
clk_put(clk);
}
}
static struct notifier_block sci_nb = { &sci_notifier, NULL, 0 };
-#endif /* CONFIG_CPU_FREQ */
+#endif /* CONFIG_CPU_FREQ && CONFIG_HAVE_CLK */
static int sci_request_irq(struct sci_port *port)
{
if (s->enable)
s->enable(port);
-#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#ifdef CONFIG_HAVE_CLK
s->clk = clk_get(NULL, "module_clk");
#endif
if (s->disable)
s->disable(port);
-#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#ifdef CONFIG_HAVE_CLK
clk_put(s->clk);
s->clk = NULL;
#endif
{
struct sci_port *s = &sci_ports[port->line];
unsigned int status, baud, smr_val;
- int t;
+ int t = -1;
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
-
- switch (baud) {
- case 0:
- t = -1;
- break;
- default:
- {
-#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
- t = SCBRR_VALUE(baud, clk_get_rate(s->clk));
-#else
- t = SCBRR_VALUE(baud);
-#endif
- break;
- }
- }
+ if (likely(baud))
+ t = SCBRR_VALUE(baud, port->uartclk);
do {
status = sci_in(port, SCxSR);
sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
-#if !defined(SCI_ONLY)
if (port->type == PORT_SCIF)
sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
-#endif
smr_val = sci_in(port, SCSMR) & 3;
if ((termios->c_cflag & CSIZE) == CS7)
case PORT_IRDA: return "irda";
}
- return 0;
+ return NULL;
}
static void sci_release_port(struct uart_port *port)
break;
}
-#if defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
- if (port->mapbase == 0)
+ if (port->flags & UPF_IOREMAP && !port->membase) {
+#if defined(CONFIG_SUPERH64)
port->mapbase = onchip_remap(SCIF_ADDR_SH5, 1024, "SCIF");
-
- port->membase = (void __iomem *)port->mapbase;
+ port->membase = (void __iomem *)port->mapbase;
+#else
+ port->membase = ioremap_nocache(port->mapbase, 0x40);
#endif
+
+ printk(KERN_ERR "sci: can't remap port#%d\n", port->line);
+ }
}
static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
{
struct sci_port *s = &sci_ports[port->line];
- if (ser->irq != s->irqs[SCIx_TXI_IRQ] || ser->irq > NR_IRQS)
+ if (ser->irq != s->irqs[SCIx_TXI_IRQ] || ser->irq > nr_irqs)
return -EINVAL;
if (ser->baud_base < 2400)
/* No paper tape reader for Mitch.. */
sci_ports[i].disable = h8300_sci_disable;
#endif
sci_ports[i].port.uartclk = CONFIG_CPU_CLOCK;
-#elif defined(CONFIG_SUPERH64)
- sci_ports[i].port.uartclk = current_cpu_data.module_clock * 16;
-#else
+#elif defined(CONFIG_HAVE_CLK)
/*
* XXX: We should use a proper SCI/SCIF clock
*/
{
struct clk *clk = clk_get(NULL, "module_clk");
- sci_ports[i].port.uartclk = clk_get_rate(clk) * 16;
+ sci_ports[i].port.uartclk = clk_get_rate(clk);
clk_put(clk);
}
+#else
+#error "Need a valid uartclk"
#endif
sci_ports[i].break_timer.data = (unsigned long)&sci_ports[i];
port->type = serial_console_port->type;
-#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#ifdef CONFIG_HAVE_CLK
if (!serial_console_port->clk)
serial_console_port->clk = clk_get(NULL, "module_clk");
#endif
static int __devinit sci_probe(struct platform_device *dev)
{
struct plat_sci_port *p = dev->dev.platform_data;
- int i;
+ int i, ret = -EINVAL;
for (i = 0; p && p->flags != 0; p++, i++) {
struct sci_port *sciport = &sci_ports[i];
sciport->port.mapbase = p->mapbase;
- /*
- * For the simple (and majority of) cases where we don't need
- * to do any remapping, just cast the cookie directly.
- */
- if (p->mapbase && !p->membase && !(p->flags & UPF_IOREMAP))
- p->membase = (void __iomem *)p->mapbase;
+ if (p->mapbase && !p->membase) {
+ if (p->flags & UPF_IOREMAP) {
+ p->membase = ioremap_nocache(p->mapbase, 0x40);
+ if (IS_ERR(p->membase)) {
+ ret = PTR_ERR(p->membase);
+ goto err_unreg;
+ }
+ } else {
+ /*
+ * For the simple (and majority of) cases
+ * where we don't need to do any remapping,
+ * just cast the cookie directly.
+ */
+ p->membase = (void __iomem *)p->mapbase;
+ }
+ }
sciport->port.membase = p->membase;
kgdb_putchar = kgdb_sci_putchar;
#endif
-#ifdef CONFIG_CPU_FREQ
+#if defined(CONFIG_CPU_FREQ) && defined(CONFIG_HAVE_CLK)
cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
dev_info(&dev->dev, "CPU frequency notifier registered\n");
#endif
#endif
return 0;
+
+err_unreg:
+ for (i = i - 1; i >= 0; i--)
+ uart_remove_one_port(&sci_uart_driver, &sci_ports[i].port);
+
+ return ret;
}
static int __devexit sci_remove(struct platform_device *dev)
projects / linux-2.6-omap-h63xx.git / blobdiff